Linking flood peak, flood volume and inundation extent: a DEM-based approach

Science.gov (United States)

Rebolho, Cédric; Furusho-Percot, Carina; Blaquière, Simon; Brettschneider, Marco; Andréassian, Vazken

2017-04-01

Traditionally, flood inundation maps are computed based on the Shallow Water Equations (SWE) in one or two dimensions, with various simplifications that have proved to give good results. However, the complexity of the SWEs often requires a numerical resolution which can need long computing time, as well as detailed cross section data: this often results in restricting these models to rather small areas abundant with high quality data. This, along with the necessity for fast inundation mapping, are the reason why rapid inundation models are being designed, working for (almost) any river with a minimum amount of data and, above all, easily available data. Our model tries to follow this path by using a 100m DEM over France from which are extracted a drainage network and the associated drainage areas. It is based on two pre-existing methods: (1) SHYREG (Arnaud et al.,2013), a regionalized approach used to calculate the 2-year and 10-year flood quantiles (used as approximated bankfull flow and maximum discharge, respectively) for each river pixel of the DEM (below a 10 000 km2 drainage area) and (2) SOCOSE (Mailhol,1980), which gives, amongst other things, an empirical formula of a characteristic flood duration (for each pixel) based on catchment area, average precipitation and temperature. An overflow volume for each river pixel is extracted from a triangular shaped synthetic hydrograph designed with SHYREG quantiles and SOCOSE flood duration. The volume is then spread from downstream to upstream one river pixel at a time. When the entire hydrographic network is processed, the model stops and generates a map of potential inundation area associated with the 10-year flood quantile. Our model can also be calibrated using past-events inundation maps by adjusting two parameters, one which modifies the overflow duration, and the other, equivalent to a minimum drainage area for river pixels to be flooded. Thus, in calibration on a sample of 42 basins, the first draft of the

Tohoku-Oki Earthquake Tsunami Runup and Inundation Data for Sites Around the Island of Hawaiʻi

Science.gov (United States)

Trusdell, Frank A.; Chadderton, Amy; Hinchliffe, Graham; Hara, Andrew; Patenge, Brent; Weber, Tom

2012-01-01

At 0546 U.t.c. March 11, 2011, a Mw 9.0 ("great") earthquake occurred near the northeast coast of Honshu Island, Japan, generating a large tsunami that devastated the east coast of Japan and impacted many far-flung coastal sites around the Pacific Basin. After the earthquake, the Pacific Tsunami Warning Center issued a tsunami alert for the State of Hawaii, followed by a tsunami-warning notice from the local State Civil Defense on March 10, 2011 (Japan is 19 hours ahead of Hawaii). After the waves passed the islands, U.S. Geological Survey (USGS) scientists from the Hawaiian Volcano Observatory (HVO) measured inundation (maximum inland distance of flooding), runup (elevation at maximum extent of inundation) and took photographs in coastal areas around the Island of Hawaiʻi. Although the damage in West Hawaiʻi is well documented, HVO's mapping revealed that East Hawaiʻi coastlines were also impacted by the tsunami. The intent of this report is to provide runup and inundation data for sites around the Island of Hawaiʻi.

Automated inundation monitoring using TerraSAR-X multitemporal imagery

Science.gov (United States)

Gebhardt, S.; Huth, J.; Wehrmann, T.; Schettler, I.; Künzer, C.; Schmidt, M.; Dech, S.

2009-04-01

The Mekong Delta in Vietnam offers natural resources for several million inhabitants. However, a strong population increase, changing climatic conditions and regulatory measures at the upper reaches of the Mekong lead to severe changes in the Delta. Extreme flood events occur more frequently, drinking water availability is increasingly limited, soils show signs of salinization or acidification, species and complete habitats diminish. During the Monsoon season the river regularly overflows its banks in the lower Mekong area, usually with beneficial effects. However, extreme flood events occur more frequently causing extensive damage, on the average once every 6 to 10 years river flood levels exceed the critical beneficial level X-band SAR data are well suited for deriving inundated surface areas. The TerraSAR-X sensor with its different scanning modi allows for the derivation of spatial and temporal high resolved inundation masks. The paper presents an automated procedure for deriving inundated areas from TerraSAR-X Scansar and Stripmap image data. Within the framework of the German-Vietnamese WISDOM project, focussing the Mekong Delta region in Vietnam, images have been acquired covering the flood season from June 2008 to November 2008. Based on these images a time series of the so called watermask showing inundated areas have been derived. The product is required as intermediate to (i) calibrate 2d inundation model scenarios, (ii) estimate the extent of affected areas, and (iii) analyze the scope of prior crisis. The image processing approach is based on the assumption that water surfaces are forward scattering the radar signal resulting in low backscatter signals to the sensor. It uses multiple grey level thresholds and image morphological operations. The approach is robust in terms of automation, accuracy, robustness, and processing time. The resulting watermasks show the seasonal flooding pattern with inundations starting in July, having their peak at the end

Mapping Regional Inundation with Spaceborne L-Band SAR

Directory of Open Access Journals (Sweden)

Bruce Chapman

2015-04-01

Full Text Available Shortly after the launch of ALOS PALSAR L-band SAR by the Japan Space Exploration Agency (JAXA, a program to develop an Earth Science Data Record (ESDR for inundated wetlands was funded by NASA. Using established methodologies, extensive multi-temporal L-band ALOS ScanSAR data acquired bi-monthly by the PALSAR instrument onboard ALOS were used to classify the inundation state for South America for delivery as a component of this Inundated Wetlands ESDR (IW-ESDR and in collaboration with JAXA’s ALOS Kyoto and Carbon Initiative science programme. We describe these methodologies and the final classification of the inundation state, then compared this with results derived from dual-season data acquired by the JERS-1 L-band SAR mission in 1995 and 1996, as well as with estimates of surface water extent measured globally every 10 days by coarser resolution sensors. Good correspondence was found when comparing open water extent classified from multi-temporal ALOS ScanSAR data with surface water fraction identified from coarse resolution sensors, except in those regions where there may be differences in sensitivity to widespread and shallow seasonal flooding event, or in areas that could be excluded through use of a continental-scale inundatable mask. It was found that the ALOS ScanSAR classification of inundated vegetation was relatively insensitive to inundated herbaceous vegetation. Inundation dynamics were examined using the multi-temporal ALOS ScanSAR acquisitions over the Pacaya-Samiria and surrounding areas in the Peruvian Amazon.

Flood-inundation maps for the West Branch Delaware River, Delhi, New York, 2012

Science.gov (United States)

Coon, William F.; Breaker, Brian K.

2012-01-01

Digital flood-inundation maps for a 5-mile reach of the West Branch Delaware River through the Village and part of the Town of Delhi, New York, were created by the U.S. Geological Survey (USGS) in cooperation with the Village of Delhi, the Delaware County Soil and Water Conservation District, and the Delaware County Planning Department. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ and the Federal Flood Inundation Mapper Web site at http://wim.usgs.gov/FIMI/FloodInundationMapper.html, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) referenced to the USGS streamgage at West Branch Delaware River upstream from Delhi, N.Y. (station number 01421900). In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model that had been used to produce the flood insurance rate maps for the most recent flood insurance study for the Town and Village of Delhi. This hydraulic model was used to compute 10 water-surface profiles for flood stages at 1-foot (ft) intervals referenced to the streamgage datum and ranging from 7 ft or near bankfull to 16 ft, which exceeds the stages that correspond to both the estimated 0.2-percent annual-exceedance-probability flood (500-year recurrence interval flood) and the maximum recorded peak flow. The simulated water-surface profiles were then combined with a geographic information system (GIS) digital elevation model, which was derived from Light Detection and Ranging (LiDAR) data with a 1.2-ft (0.61-ft root mean squared error) vertical accuracy and 3.3-ft (1-meter) horizontal resolution, to delineate the area flooded at each water level. A map that was produced using this method to delineate the inundated area for the flood that occurred on August 28, 2011, agreed well with highwater marks that had been located in the field using a

Hurricane Matthew (2016) and its Storm Surge Inundation under Global Warming Scenarios: Application of an Interactively Coupled Atmosphere-Ocean Model

Science.gov (United States)

Jisan, M. A.; Bao, S.; Pietrafesa, L.; Pullen, J.

2017-12-01

An interactively coupled atmosphere-ocean model was used to investigate the impacts of future ocean warming, both at the surface and the layers below, on the track and intensity of a hurricane and its associated storm surge and inundation. The category-5 hurricane Matthew (2016), which made landfall on the South Carolina coast of the United States, was used for the case study. Future ocean temperature changes and sea level rise (SLR) were estimated based on the projection of Inter-Governmental Panel on Climate Change (IPCC)'s Representative Concentration Pathway scenarios RCP 2.6 and RCP 8.5. After being validated with the present-day observational data, the model was applied to simulate the changes in track, intensity, storm surge and inundation that Hurricane Matthew would cause under future climate change scenarios. It was found that a significant increase in hurricane intensity, storm surge water level, and inundation area for Hurricane Matthew under future ocean warming and SLR scenarios. For example, under the RCP 8.5 scenario, the maximum wind speed would increase by 17 knots (14.2%), the minimum sea level pressure would decrease by 26 hPa (2.85%), and the inundated area would increase by 401 km2 (123%). By including the effect of SLR for the middle-21st-century scenario, the inundated area will further increase by up to 49.6%. The increase in the hurricane intensity and the inundated area was also found for the RCP 2.6 scenario. The response of sea surface temperature was analyzed to investigate the change in intensity. A comparison was made between the impacts when only the sea surface warming is considered versus when both the sea surface and the underneath layers are considered. These results showed that even without the effect of SLR, the storm surge level and the inundated area would be higher due to the increased hurricane intensity under the influence of the future warmer ocean temperature. The coupled effect of ocean warming and SLR would cause the

Inundation and Fire Shape the Structure of Riparian Forests in the Pantanal, Brazil.

Science.gov (United States)

Arruda, Wellinton de Sá; Oldeland, Jens; Paranhos Filho, Antonio Conceição; Pott, Arnildo; Cunha, Nicolay L; Ishii, Iria Hiromi; Damasceno-Junior, Geraldo Alves

2016-01-01

Inundation and fire can affect the structure of riparian vegetation in wetlands. Our aim was to verify if there are differences in richness, abundance, basal area, composition and topographic preference of woody species in riparian forests related to the fire history, flooding duration, or the interaction between both. The study was conducted in the riparian forests of the Paraguay River some of which were burned three times between 2001 and 2011. We sampled trees with a girth of at least 5 cm at breast height in 150 5 × 10 m plots (79 burned and 71 unburned). We also measured height of the flood mark and estimated the flooding duration of each plot. We performed Generalized Linear Mixed Models to verify differences in richness, basal area, and abundance of individuals associated to interaction of fire and inundation. We used an analysis of similarity (ANOSIM) and indicator species analysis to identify differences in composition of species and the association with burned and unburned area according to different levels of inundation. Finally, we used a hierarchical set of Generalized Linear Models (GLM), the so-called HOF models, to analyse each species' specific response to inundation based on topography and to determine their preferred optimal topographic position for both burned as well as unburned areas. Richness was positively associated with elevation only in burned areas while abundance was negatively influenced by inundation only in burned areas. Basal area was negatively associated with time of inundation independent of fire history. There were 15 species which were significant indicators for at least one combination of the studied factors. We found nine species in burned areas and 15 in unburned areas, with response curves in HOF models along the inundation gradient. From these, five species shifted their optimal position along the inundation gradient in burned areas. The interaction of fire and inundation did not appear to affect the basal area, but it

Ohio River backwater flood-inundation maps for the Saline and Wabash Rivers in southern Illinois

Science.gov (United States)

Murphy, Elizabeth A.; Sharpe, Jennifer B.; Soong, David T.

2012-01-01

Digital flood-inundation maps for the Saline and Wabash Rivers referenced to elevations on the Ohio River in southern Illinois were created by the U.S. Geological Survey (USGS). The inundation maps, accessible through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent of flooding corresponding to selected water levels (gage heights) at the USGS streamgage at Ohio River at Old Shawneetown, Illinois-Kentucky (station number 03381700). Current gage height and flow conditions at this USGS streamgage may be obtained on the Internet at http://waterdata.usgs.gov/usa/nwis/uv?03381700. In addition, this streamgage is incorporated into the Advanced Hydrologic Prediction Service (AHPS) flood warning system (http://water.weather.gov/ahps/) by the National Weather Service (NWS). The NWS forecasts flood hydrographs at many places that are often co-located at USGS streamgages. That NWS forecasted peak-stage information, also shown on the Ohio River at Old Shawneetown inundation Web site, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, eight water-surface elevations were mapped at 5-foot (ft) intervals referenced to the streamgage datum ranging from just above the NWS Action Stage (31 ft) to above the maximum historical gage height (66 ft). The elevations of the water surfaces were compared to a Digital Elevation Model (DEM) by using a Geographic Information System (GIS) in order to delineate the area flooded at each water level. These maps, along with information on the Internet regarding current gage heights from USGS streamgages and forecasted stream stages from the NWS, provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

Elevation uncertainty in coastal inundation hazard assessments

Science.gov (United States)

Gesch, Dean B.; Cheval, Sorin

2012-01-01

Coastal inundation has been identified as an important natural hazard that affects densely populated and built-up areas (Subcommittee on Disaster Reduction, 2008). Inundation, or coastal flooding, can result from various physical processes, including storm surges, tsunamis, intense precipitation events, and extreme high tides. Such events cause quickly rising water levels. When rapidly rising water levels overwhelm flood defenses, especially in heavily populated areas, the potential of the hazard is realized and a natural disaster results. Two noteworthy recent examples of such natural disasters resulting from coastal inundation are the Hurricane Katrina storm surge in 2005 along the Gulf of Mexico coast in the United States, and the tsunami in northern Japan in 2011. Longer term, slowly varying processes such as land subsidence (Committee on Floodplain Mapping Technologies, 2007) and sea-level rise also can result in coastal inundation, although such conditions do not have the rapid water level rise associated with other flooding events. Geospatial data are a critical resource for conducting assessments of the potential impacts of coastal inundation, and geospatial representations of the topography in the form of elevation measurements are a primary source of information for identifying the natural and human components of the landscape that are at risk. Recently, the quantity and quality of elevation data available for the coastal zone have increased markedly, and this availability facilitates more detailed and comprehensive hazard impact assessments.

Flood-inundation maps for the St. Marys River at Decatur, Indiana

Science.gov (United States)

Strauch, Kellan R.

2015-08-24

Digital flood-inundation maps for an 8.9-mile reach of the St. Marys River at Decatur, Indiana, were developed by the U.S. Geological Survey (USGS), in cooperation with the Indiana Office of Community and Rural Affairs. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site (http://water.usgs.gov/osw/flood_inundation/), depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) of the St. Marys River at Decatur (USGS station number 04181500). The maps are useful for estimating near-real-time areas of inundation by referencing concurrent USGS streamgage information at http://waterdata.usgs.gov/. In addition, the streamgage information was provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service flood warning system (http:/water.weather.gov/ahps/). NWS-forecasted peak-stage information may be used in conjunction with the maps developed during this study to show predicted areas of flood inundation.

Evaluation of Airborne Lidar Elevation Surfaces for Propagation of Coastal Inundation: The Importance of Hydrologic Connectivity

Directory of Open Access Journals (Sweden)

Sandra Poppenga

2015-09-01

Full Text Available Detailed information about coastal inundation is vital to understanding dynamic and populated areas that are impacted by storm surge and flooding. To understand these natural hazard risks, lidar elevation surfaces are frequently used to model inundation in coastal areas. A single-value surface method is sometimes used to inundate areas in lidar elevation surfaces that are below a specified elevation value. However, such an approach does not take into consideration hydrologic connectivity between elevation grids cells resulting in inland areas that should be hydrologically connected to the ocean, but are not. Because inland areas that should drain to the ocean are hydrologically disconnected by raised features in a lidar elevation surface, simply raising the water level to propagate coastal inundation will lead to inundation uncertainties. We took advantage of this problem to identify hydrologically disconnected inland areas to point out that they should be considered for coastal inundation, and that a lidar-based hydrologic surface should be developed with hydrologic connectivity prior to inundation analysis. The process of achieving hydrologic connectivity with hydrologic-enforcement is not new, however, the application of hydrologically-enforced lidar elevation surfaces for improved coastal inundation mapping as approached in this research is innovative. In this article, we propagated a high-resolution lidar elevation surface in coastal Staten Island, New York to demonstrate that inland areas lacking hydrologic connectivity to the ocean could potentially be included in inundation delineations. For inland areas that were hydrologically disconnected, we evaluated if drainage to the ocean was evident, and calculated an area exceeding 11 ha (~0.11 km2 that could be considered in inundation delineations. We also assessed land cover for each inland area to determine the type of physical surfaces that would be potentially impacted if the inland areas

Evaluation of airborne lidar elevation surfaces for propagation of coastal inundation: the importance of hydrologic connectivity

Science.gov (United States)

Poppenga, Sandra K.; Worstell, Bruce B.

2015-01-01

Detailed information about coastal inundation is vital to understanding dynamic and populated areas that are impacted by storm surge and flooding. To understand these natural hazard risks, lidar elevation surfaces are frequently used to model inundation in coastal areas. A single-value surface method is sometimes used to inundate areas in lidar elevation surfaces that are below a specified elevation value. However, such an approach does not take into consideration hydrologic connectivity between elevation grids cells resulting in inland areas that should be hydrologically connected to the ocean, but are not. Because inland areas that should drain to the ocean are hydrologically disconnected by raised features in a lidar elevation surface, simply raising the water level to propagate coastal inundation will lead to inundation uncertainties. We took advantage of this problem to identify hydrologically disconnected inland areas to point out that they should be considered for coastal inundation, and that a lidar-based hydrologic surface should be developed with hydrologic connectivity prior to inundation analysis. The process of achieving hydrologic connectivity with hydrologic-enforcement is not new, however, the application of hydrologically-enforced lidar elevation surfaces for improved coastal inundation mapping as approached in this research is innovative. In this article, we propagated a high-resolution lidar elevation surface in coastal Staten Island, New York to demonstrate that inland areas lacking hydrologic connectivity to the ocean could potentially be included in inundation delineations. For inland areas that were hydrologically disconnected, we evaluated if drainage to the ocean was evident, and calculated an area exceeding 11 ha (~0.11 km2) that could be considered in inundation delineations. We also assessed land cover for each inland area to determine the type of physical surfaces that would be potentially impacted if the inland areas were considered as

Utilising social media contents for flood inundation mapping

Science.gov (United States)

Schröter, Kai; Dransch, Doris; Fohringer, Joachim; Kreibich, Heidi

2016-04-01

Data about the hazard and its consequences are scarce and not readily available during and shortly after a disaster. An information source which should be explored in a more efficient way is eyewitness accounts via social media. This research presents a methodology that leverages social media content to support rapid inundation mapping, including inundation extent and water depth in the case of floods. It uses quantitative data that are estimated from photos extracted from social media posts and their integration with established data. Due to the rapid availability of these posts compared to traditional data sources such as remote sensing data, areas affected by a flood, for example, can be determined quickly. Key challenges are to filter the large number of posts to a manageable amount of potentially useful inundation-related information, and to interpret and integrate the posts into mapping procedures in a timely manner. We present a methodology and a tool ("PostDistiller") to filter geo-located posts from social media services which include links to photos and to further explore this spatial distributed contextualized in situ information for inundation mapping. The June 2013 flood in Dresden is used as an application case study in which we evaluate the utilization of this approach and compare the resulting spatial flood patterns and inundation depths to 'traditional' data sources and mapping approaches like water level observations and remote sensing flood masks. The outcomes of the application case are encouraging. Strengths of the proposed procedure are that information for the estimation of inundation depth is rapidly available, particularly in urban areas where it is of high interest and of great value because alternative information sources like remote sensing data analysis do not perform very well. The uncertainty of derived inundation depth data and the uncontrollable availability of the information sources are major threats to the utility of the approach.

Lake Izabal (Guatemala) shoreline detection and inundated area estimation from ENVISAT ASAR images

Science.gov (United States)

Medina, C.; Gomez-Enri, J.; Alonso, J. J.; Villares, P.

2008-10-01

The surface extent of a lake reflects its water storage variations. This information has important hydrological and operational applications. However, there is a lack of information regarding this subject because the traditional methodologies for this purposes (ground surveys, aerial photos) requires high resources investments. Remote sensing techniques (optical/radar sensors) permit a low cost, constant and accurate monitoring of this parameter. The objective of this study was to determine the surface variations of Lake Izabal, the largest one in Guatemala. The lake is located close to the Caribbean Sea coastline. The climate in the region is predominantly cloudy and rainy, being the Synthetic Aperture Radar (SAR) the best suited sensor for this purpose. Although several studies have successfully used SAR products in detecting land-water boundaries, all of them highlighted some sensor limitations. These limitations are mainly caused by roughened water surfaces caused by strong winds which are frequent in Lake Izabal. The ESA's ASAR data products were used. From the set of 9 ASAR images used, all of them have wind-roughened ashore waters in several levels. Here, a chain of image processing steps were applied in order to extract a reliable shoreline. The shoreline detection is the key task for the surface estimation. After the shoreline extraction, the inundated area of the lake was estimated. In-situ lake level measurements were used for validation. The results showed good agreement between the inundated areas estimations and the lake level gauges.

Inundation Mapping for Heterogeneous Land Covers with Synthetic Aperture Radar and Auxiliary Data

Science.gov (United States)

Aristizabal, F.; Judge, J.

2017-12-01

Synthetic Aperture Radar (SAR) has been widely used to detect surface water inundation and provides an advantage over multi-spectral instruments due to cloud penetration and higher spatial resolutions. However, detecting inundation for densely vegetated and urban areas with SAR remains a challenge due to corner reflection and diffuse scattering. Additionally, flat urban surfaces such as roads exhibit similar backscatter coefficients as urban surface water. Differences between inundated and non-inundated backscatter over vegetated land covers of static spatial domains have been demonstrated in previous studies. However, these backscatter differences are sensitive to changes in water depth, soil moisture, SAR sensor parameters, terrain, and vegetation properties. These factors tend to make accurate inundation mapping of heterogeneous regions across varying spatial and temporal extents difficult with exclusive use of SAR. This study investigates the utility of auxiliary data specifically high-resolution (10m) terrain information in conjunction with SAR (10m) for detecting inundated areas. Digital elevation models provide an absolute elevation which could enhance inundation mapping given a limited study extent with similar topography. To counter this limitation, a hydrologically relevant terrain index is proposed known as the Height Above Nearest Drainage (HAND) which normalizes topography to the local relative elevation of the nearest point along the relevant drainage line. HAND has been used for assisting remote sensing inundation mapping in the pre-processing stage as a terrain correction tool and as a post-processing mask that eliminates areas of low inundation risk. While the latter technique is useful for reduction of commission errors, it does not employ HAND for reducing omission errors that can occur from dense vegetation, spectral noise, and urban features. Sentinel-1 dual-pol SAR as well as auxiliary HAND will be used as predictors by various supervised and

Characterization of peak streamflows and flood inundation at selected areas in North Carolina following Hurricane Matthew, October 2016

Science.gov (United States)

Musser, Jonathan W.; Watson, Kara M.; Gotvald, Anthony J.

2017-05-05

The passage of Hurricane Matthew through central and eastern North Carolina during October 7–9, 2016, brought heavy rainfall, which resulted in major flooding. More than 15 inches of rain was recorded in some areas. More than 600 roads were closed, including Interstates 95 and 40, and nearly 99,000 structures were affected by floodwaters. Immediately following the flooding, the U.S. Geological Survey documented 267 high-water marks, of which 254 were surveyed. North Carolina Emergency Management documented and surveyed 353 high-water marks. Using a subset of these highwater marks, six flood-inundation maps were created for hard-hit communities. Digital datasets of the inundation areas, study reach boundary, and water-depth rasters are available for download. In addition, peak gage-height data, peak streamflow data, and annual exceedance probabilities (in percent) were determined for 24 U.S. Geological Survey streamgages located near the heavily flooded communities.

[Characteristics of dissolved organic carbon release under inundation from typical grass plants in the water-level fluctuation zone of the Three Gorges Reservoir area].

Science.gov (United States)

Tan, Qiu-Xia; Zhu, Boi; Hua, Ke-Ke

2013-08-01

The water-level fluctuation zone of the Three Gorges Reservoir (TGR) exposes in spring and summer, then, green plants especially herbaceous plants grow vigorously. In the late of September, water-level fluctuation zone of TGR goes to inundation. Meanwhile, annually accumulated biomass of plant will be submerged for decaying, resulting in organism decomposition and release a large amount of dissolved organic carbon (DOC). This may lead to negative impacts on water environment of TGR. The typical herbaceous plants from water-level fluctuation zone were collected and inundated in the laboratory for dynamic measurements of DOC concentration of overlying water. According to the determination, the DOC release rates and fluxes have been calculated. Results showed that the release process of DOC variation fitted in a parabolic curve. The peak DOC concentrations emerge averagely in the 15th day of inundation, indicating that DOC released quickly with organism decay of herbaceous plant. The release process of DOC could be described by the logarithm equation. There are significant differences between the concentration of DOC (the maximum DOC concentration is 486.88 mg x L(-1) +/- 35.97 mg x L(-1) for Centaurea picris, the minimum is 4.18 mg x L(-1) +/- 1.07 mg x L(-1) for Echinochloacrus galli) and the release amount of DOC (the maximum is 50.54 mg x g(-1) for Centaurea picris, the minimum is 6.51 mg x g(-1) for Polygonum hydropiper) due to different characteristics of plants, especially, the values of C/N of herbaceous plants. The cumulative DOC release quantities during the whole inundation period were significantly correlated with plants' C/N values in linear equations.

MODEL SPASIAL DINAMIK GENANGAN AKIBAT KENAIKAN MUKA AIR LAUT DI PESISIR SEMARANG (Spatial Dynamic Model of Inundated area due to Sea Level rise at Semarang coastal Area

Directory of Open Access Journals (Sweden)

Ifan R Suhelmi

2014-05-01

Full Text Available ABSTRAK Kota Semarang merupakan kota pesisir di Provinsi Jawa Tengah yang memiliki topografi datar pada wilayah laut yang biasa disebut dengan kota bawah dan bergunung pada bagian atasnya yang biasa disebut dengan kota atas. Kota bawah memiliki kerentanan yang tinggi terhadap genangan akibat kenaikan muka air laut, hal ini disebabkan olehkondisi topografi yang datar. Penelitian ini dilakukan untuk memberikan gambaran secara dinamik distribusi genangan akibat berbagai skenario kenaikan muka air laut. Model spasial dinamik menggunakan Flash yang berfungsi memberikan gambaran secara interaktif dan real time pada berbagai skenario kenaikan muka air laut. Skenario kenaikan muka air laut menggunakan skenario IPCC hingga tahun 2100. Hasil studi menunjukkan bahwa terjadi kenaikan jumlah genangan dari 599,4 ha pada tahun 2020 menjadi 4.235,4 ha pada tahun 2100.   ABSTRACT Semarang is one of coastal city located at Central Java Province. It has flatten topography at coastal area called “downside town” and hilly topography at upper area called “topside town”.  Ownside town was highly vulnerable to sea level rise caused by it’s topographic condition and the land subsidence phenomena. This research conducted to mapeed the inundated area due to sea level rise at many scenarios of sea level rise. The dynamic spatialmodel of sea level rise represented using flash techmology to showed distributed area inundated by sea level rise. The scenario of sea level rise by IPCC prediction was used at this study. The stuty showed that the inundated area increased from 599.4 ha at year 2020 to 4,235.4 ha at 2100.

Online multistep-ahead inundation depth forecasts by recurrent NARX networks

Directory of Open Access Journals (Sweden)

H.-Y. Shen

2013-03-01

Full Text Available Various types of artificial neural networks (ANNs have been successfully applied in hydrological fields, but relatively scant on multistep-ahead flood inundation forecasting, which is very difficult to achieve, especially when dealing with forecasts without regular observed data. This study proposes a recurrent configuration of nonlinear autoregressive with exogenous inputs (NARX network, called R-NARX, to forecast multistep-ahead inundation depths in an inundation area. The proposed R-NARX is constructed based on the recurrent neural network (RNN, which is commonly used for modeling nonlinear dynamical systems. The models were trained and tested based on a large number of inundation data generated by a well validated two-dimensional simulation model at thirteen inundation-prone sites in Yilan County, Taiwan. We demonstrate that the R-NARX model can effectively inhibit error growth and accumulation when being applied to online multistep-ahead inundation forecasts over a long lasting forecast period. For comparison, a feedforward time-delay and an online feedback configuration of NARX networks (T-NARX and O-NARX were performed. The results show that (1 T-NARX networks cannot make online forecasts due to unavailable inputs in the constructed networks even though they provide the best performances for reference only; and (2 R-NARX networks consistently outperform O-NARX networks and can be adequately applied to online multistep-ahead forecasts of inundation depths in the study area during typhoon events.

Flood-inundation maps for the Flatrock River at Columbus, Indiana, 2012

Science.gov (United States)

Coon, William F.

2013-01-01

Digital flood-inundation maps for a 5-mile reach of the Flatrock River on the western side of Columbus, Indiana, from County Road 400N to the river mouth at the confluence with Driftwood River, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ and the Federal Flood Inundation Mapper Web site at http://wim.usgs.gov/FIMI/FloodInundationMapper.html, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage on the Flatrock River at Columbus (station number 03363900). Near-real-time stages at this streamgage may be obtained on the Internet from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service (NWS) Advanced Hydrologic Prediction Service, which also presents the USGS data, at http:/water.weather.gov/ahps/. Flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated by using the most current stage-discharge relation at the Flatrock River streamgage, high-water marks that were surveyed following the flood of June 7, 2008, and water-surface profiles from the current flood-insurance study for the City of Columbus. The hydraulic model was then used to compute 12 water-surface profiles for flood stages at 1-foot (ft) intervals referenced to the streamgage datum and ranging from 9 ft or near bankfull to 20 ft, which exceeds the stages that correspond to both the estimated 0.2-percent annual exceedance probability flood (500-year recurrence interval flood) and the maximum recorded peak flow. The simulated water-surface profiles were then combined with a Geographic Information System digital elevation model (derived from Light Detection and Ranging (LiDAR) data having a 0.37 ft

Estimated flood-inundation maps for Cowskin Creek in western Wichita, Kansas

Science.gov (United States)

Studley, Seth E.

2003-01-01

The October 31, 1998, flood on Cowskin Creek in western Wichita, Kansas, caused millions of dollars in damages. Emergency management personnel and flood mitigation teams had difficulty in efficiently identifying areas affected by the flooding, and no warning was given to residents because flood-inundation information was not available. To provide detailed information about future flooding on Cowskin Creek, high-resolution estimated flood-inundation maps were developed using geographic information system technology and advanced hydraulic analysis. Two-foot-interval land-surface elevation data from a 1996 flood insurance study were used to create a three-dimensional topographic representation of the study area for hydraulic analysis. The data computed from the hydraulic analyses were converted into geographic information system format with software from the U.S. Army Corps of Engineers' Hydrologic Engineering Center. The results were overlaid on the three-dimensional topographic representation of the study area to produce maps of estimated flood-inundation areas and estimated depths of water in the inundated areas for 1-foot increments on the basis of stream stage at an index streamflow-gaging station. A Web site (http://ks.water.usgs.gov/Kansas/cowskin.floodwatch) was developed to provide the public with information pertaining to flooding in the study area. The Web site shows graphs of the real-time streamflow data for U.S. Geological Survey gaging stations in the area and monitors the National Weather Service Arkansas-Red Basin River Forecast Center for Cowskin Creek flood-forecast information. When a flood is forecast for the Cowskin Creek Basin, an estimated flood-inundation map is displayed for the stream stage closest to the National Weather Service's forecasted peak stage. Users of the Web site are able to view the estimated flood-inundation maps for selected stages at any time and to access information about this report and about flooding in general. Flood

Thermal remote sensing of water under flooded vegetation: New observations of inundation patterns for the ‘Small’ Lake Chad

Science.gov (United States)

Leblanc, M.; Lemoalle, J.; Bader, J.-C.; Tweed, S.; Mofor, L.

2011-06-01

SummaryLake Chad at the border of the Sahara desert in central Africa, is well known for its high sensitivity to hydroclimatic events. Gaps in in situ data have so far prevented a full assessment of the response of Lake Chad to the ongoing prolonged drought that started in the second half of the 20th century. Like many other wetlands and shallow lakes, the 'Small' Lake Chad includes large areas of water under aquatic vegetation which needs to be accounted for to obtain the total inundated area. In this paper, a methodology is proposed that uses Meteosat thermal maximum composite data (Tmax) to account for water covered by aquatic vegetation and provide a consistent monthly time series of total inundated area estimates for Lake Chad. Total inundation patterns in Lake Chad were reconstructed for a 15-yr period (1986-2001) which includes the peak of the drought (86-91) and therefore provides new observations on the hydrological functioning of the 'Small' Lake Chad. During the study period, Lake Chad remained below 16,400 km 2 (third quartile ˜8800 km 2). The variability of the inundated area observed in the northern pool (standard deviation σnorthern pool = 1980 km 2) is about 60% greater than that of the southern pool ( σsouthern pool = 1250 km 2). The same methodology could be applied to other large wetlands and shallow lakes in semi-arid or arid regions elsewehere using Meteosat (e.g. Niger Inland Delta, Sudd in Sudan, Okavango Delta) and other weather satellites (e.g., floodplains of the Lake Eyre Basin in Australia and Andean Altiplano Lakes in South America).

Stochastic evaluation of tsunami inundation and quantitative estimating tsunami risk

International Nuclear Information System (INIS)

Fukutani, Yo; Anawat, Suppasri; Abe, Yoshi; Imamura, Fumihiko

2014-01-01

We performed a stochastic evaluation of tsunami inundation by using results of stochastic tsunami hazard assessment at the Soma port in the Tohoku coastal area. Eleven fault zones along the Japan trench were selected as earthquake faults generating tsunamis. The results show that estimated inundation area of return period about 1200 years had good agreement with that in the 2011 Tohoku earthquake. In addition, we evaluated quantitatively tsunami risk for four types of building; a reinforced concrete, a steel, a brick and a wood at the Soma port by combining the results of inundation assessment and tsunami fragility assessment. The results of quantitative estimating risk would reflect properly vulnerability of the buildings, that the wood building has high risk and the reinforced concrete building has low risk. (author)

Evaluation of Dynamic Coastal Response to Sea-level Rise Modifies Inundation Likelihood

Science.gov (United States)

Lentz, Erika E.; Thieler, E. Robert; Plant, Nathaniel G.; Stippa, Sawyer R.; Horton, Radley M.; Gesch, Dean B.

2016-01-01

Sea-level rise (SLR) poses a range of threats to natural and built environments, making assessments of SLR-induced hazards essential for informed decision making. We develop a probabilistic model that evaluates the likelihood that an area will inundate (flood) or dynamically respond (adapt) to SLR. The broad-area applicability of the approach is demonstrated by producing 30x30m resolution predictions for more than 38,000 sq km of diverse coastal landscape in the northeastern United States. Probabilistic SLR projections, coastal elevation and vertical land movement are used to estimate likely future inundation levels. Then, conditioned on future inundation levels and the current land-cover type, we evaluate the likelihood of dynamic response versus inundation. We find that nearly 70% of this coastal landscape has some capacity to respond dynamically to SLR, and we show that inundation models over-predict land likely to submerge. This approach is well suited to guiding coastal resource management decisions that weigh future SLR impacts and uncertainty against ecological targets and economic constraints.

The impact of onsite wastewater disposal systems on groundwater in areas inundated by Hurricane Sandy in New York and New Jersey

Science.gov (United States)

Fisher, Irene; Phillips, Patrick J.; Colella, Kaitlyn; Fisher, Shawn C.; Tagliaferri, Tristen N.; Foreman, William T.; Furlong, Edward T.

2016-01-01

Coastal onsite wastewater disposal systems (OWDS) were inundated by Hurricane Sandy's storm tide. This study compares the shallow groundwater quality (nutrients, pharmaceuticals, and hormones) downgradient of OWDS before and after Hurricane Sandy, where available, and establishes a baseline for wastewater influence on groundwater in coastal communities inundated by Hurricane Sandy. Nutrients and contaminants of emerging concern (CECs) were detected in shallow groundwater downgradient of OWDS in two settings along the New Jersey and New York coastlines: 1) a single, centralized OWDS in a park; and 2) multiple OWDS (cesspools) in low-density residential and mixed-use/medium density residential areas. The most frequently detected pharmaceuticals were lidocaine (40%), carbamazepine (36%), and fexofenadine, bupropion, desvenlafaxine, meprobamate, and tramadol (24–32%). Increases in the number and total concentration of pharmaceuticals after Hurricane Sandy may reflect other factors (seasonality, usage) besides inundation, and demonstrate the importance of analyzing for a wide variety of CECs in regional studies.

Probabilistic Mapping of Storm-induced Coastal Inundation for Climate Change Adaptation

Science.gov (United States)

Li, N.; Yamazaki, Y.; Roeber, V.; Cheung, K. F.; Chock, G.

2016-02-01

Global warming is posing an imminent threat to coastal communities worldwide. Under the IPCC RCP8.5 scenario, we utilize hurricane events downscaled from a CMIP5 global climate model using the stochastic-deterministic method of Emanuel (2013, Proc. Nat. Acad. Sci.) in a pilot study to develop an inundation map with projected sea-level rise for the urban Honolulu coast. The downscaling is performed for a 20-year period from 2081 to 2100 to capture the ENSO, which strongly influences the hurricane activity in the Pacific. A total of 50 simulations provide a quasi-stationary dataset of 1000 years for probabilistic analysis of the flood hazards toward the end of the century. We utilize the meta-model Hakou, which is based on precomputed hurricane scenarios using ADCIRC, SWAN, and a 1D Boussinesq model (Kennedy et al., 2012, Ocean Modelling), to estimate the annual maximum inundation along the project coastline at the present sea level. Screening of the preliminary results identifies the most severe three events for detailed inundation modeling using the package of Li et al. (2014, Ocean Modelling) at the projected sea level. For each event, the third generation spectral model WAVEWATCH III of Tolman (2008, Ocean Modelling) provides the hurricane waves and the circulation model NEOWAVE of Yamazaki et al. (2009, 2011, Int. J. Num. Meth. Fluids) computes the surge using a system of telescopic nested grids from the open ocean to the project coastline. The output defines the boundary conditions and initial still-water elevation for computation of phase-resolving surf-zone and inundation processes using the 2D Boussinesq model of Roeber and Cheung (2012, Coastal Engineering). Each computed inundation event corresponds to an annual maximum, and with 1000 years of data, has an occurrence probability of 0.1% in a given year. Barring the tail of the distribution, aggregation of the three computed events allow delineation of the inundation zone with annual exceedance probability

DEVELOPING A SPATIAL PROCESSING SERVICE FOR AUTOMATIC CALCULATION OF STORM INUNDATION

Directory of Open Access Journals (Sweden)

H. Jafari

2017-09-01

Full Text Available With the increase in urbanization, the surface of earth and its climate are changing. These changes resulted in more frequent floodingand storm inundation in urban areas. The challenges of flooding can be addressed through several computational procedures. Due to its numerous advantages, accessible web services can be chosen as a proper format for determining the storm inundation. Web services have facilitated the integration and interactivity of the web applications. Such services made the interaction between machines more feasible. Web services enable the heterogeneous software systems to communicate with each other. A Web Processing Service (WPS makes it possible to process spatial data with different formats. In this study, we developed a WPS to automatically calculate the amount of storm inundation caused by rainfall in urban areas. The method we used for calculating the storm inundation is based on a simplified hydrologic model which estimates the final status of inundation. The simulation process and water transfer between subcatchments are carried out respectively, without user’s interference. The implementation of processing functions in a form of processing web services gives the capability to reuse the services and apply them in other services. As a result, it would avoid creating the duplicate resources.

Downscaling Surface Water Inundation from Coarse Data to Fine-Scale Resolution: Methodology and Accuracy Assessment

Directory of Open Access Journals (Sweden)

Guiping Wu

2015-11-01

Full Text Available The availability of water surface inundation with high spatial resolution is of fundamental importance in several applications such as hydrology, meteorology and ecology. Medium spatial resolution sensors, like MODerate-resolution Imaging Spectroradiometer (MODIS, exhibit a significant potential to study inundation dynamics over large areas because of their high temporal resolution. However, the low spatial resolution provided by MODIS is not appropriate to accurately delineate inundation over small scale. Successful downscaling of water inundation from coarse to fine resolution would be crucial for improving our understanding of complex inundation characteristics over the regional scale. Therefore, in this study, we propose an innovative downscaling method based on the normalized difference water index (NDWI statistical regression algorithm towards generating small-scale resolution inundation maps from MODIS data. The method was then applied to the Poyang Lake of China. To evaluate the performance of the proposed downscaling method, qualitative and quantitative comparisons were conducted between the inundation extent of MODIS (250 m, Landsat (30 m and downscaled MODIS (30 m. The results indicated that the downscaled MODIS (30 m inundation showed significant improvement over the original MODIS observations when compared with simultaneous Landsat (30 m inundation. The edges of the lakes become smoother than the results from original MODIS image and some undetected water bodies were delineated with clearer shapes in the downscaled MODIS (30 m inundation map. With respect to high-resolution Landsat TM/ETM+ derived inundation, the downscaling procedure has significantly increased the R2 and reduced RMSE and MAE both for the inundation area and for the value of landscape metrics. The main conclusion of this study is that the downscaling algorithm is promising and quite feasible for the inundation mapping over small-scale lakes.

Identification of erosional and inundation hazard zones in Ken-Betwa river linking area, India, using remote sensing and GIS.

Science.gov (United States)

Avtar, Ram; Singh, Chander Kumar; Shashtri, Satayanarayan; Mukherjee, Saumitra

2011-11-01

Ken-Betwa river link is one of the pilot projects of the Inter Linking of Rivers program of Government of India in Bundelkhand Region. It will connect the Ken and Betwa rivers through a system of dams, reservoirs, and canals to provide storage for excess rainfall during the monsoon season and avoid floods. The main objective of this study is to identify erosional and inundation prone zones of Ken-Betwa river linking site in India using remote sensing and geographic information system tools. In this study, Landsat Thematic Mapper data of year 2005, digital elevation model from the Shuttle Radar Topographic Mission, and other ancillary data were analyzed to create various thematic maps viz. geomorphology, land use/land cover, NDVI, geology, soil, drainage density, elevation, slope, and rainfall. The integrated thematic maps were used for hazard zonation. This is based on categorizing the different hydrological and geomorphological processes influencing the inundation and erosion intensity. Result shows that the southern part of the study area which lies in Panna district of Madhya Pradesh, India, is more vulnerable than the other areas.

The simulation of Typhoon-induced coastal inundation in Busan, South Korea applying the downscaling technique

Science.gov (United States)

Jang, Dongmin; Park, Junghyun; Yuk, Jin-Hee; Joh, MinSu

2017-04-01

Due to typhoons, the south coastal cities including Busan in South Korea coastal are very vulnerable to a surge, wave and corresponding coastal inundation, and are affected every year. In 2016, South Korea suffered tremendous damage by typhoon 'Chaba', which was developed near east-north of Guam on Sep. 28 and had maximum 10-minute sustained wind speed of about 50 m/s, 1-minute sustained wind speed of 75 m/s and a minimum central pressure of 905 hpa. As 'Chaba', which is the strongest since typhoon 'Maemi' in 2003, hit South Korea on Oct. 5, it caused a massive economic and casualty damage to Ulsan, Gyeongju and Busan in South Korea. In particular, the damage of typhoon-induced coastal inundation in Busan, where many high-rise buildings and residential areas are concentrated near coast, was serious. The coastal inundation could be more affected by strong wind-induced wave than surge. In fact, it was observed that the surge height was about 1 m averagely and a significant wave height was about 8 m at coastal sea nearby Busan on Oct. 5 due to 'Chaba'. Even though the typhoon-induced surge elevated the sea level, the typhoon-induced long period wave with wave period of more than 15s could play more important role in the inundation. The present work simulated the coastal inundation induced by 'Chaba' in Busan, South Korea considering the effects of typhoon-induced surge and wave. For 'Chaba' hindcast, high resolution Weather Research and Forecasting model (WRF) was applied using a reanalysis data produced by NCEP (FNL 0.25 degree) on the boundary and initial conditions, and was validated by the observation of wind speed, direction and pressure. The typhoon-induced coastal inundation was simulated by an unstructured gird model, Finite Volume Community Ocean Model (FVCOM), which is fully current-wave coupled model. To simulate the wave-induced inundation, 1-way downscaling technique of multi domain was applied. Firstly, a mother's domain including Korean peninsula was

Effective inundation of continental United States communities with 21st century sea level rise

Directory of Open Access Journals (Sweden)

Kristina A. Dahl

2017-07-01

Full Text Available Recurrent, tidally driven coastal flooding is one of the most visible signs of sea level rise. Recent studies have shown that such flooding will become more frequent and extensive as sea level continues to rise, potentially altering the landscape and livability of coastal communities decades before sea level rise causes coastal land to be permanently inundated. In this study, we identify US communities that will face effective inundation—defined as having 10% or more of livable land area flooded at least 26 times per year—with three localized sea level rise scenarios based on projections for the 3rd US National Climate Assessment. We present these results in a new, online interactive tool that allows users to explore when and how effective inundation will impact their communities. In addition, we identify communities facing effective inundation within the next 30 years that contain areas of high socioeconomic vulnerability today using a previously published vulnerability index. With the Intermediate-High and Highest sea level rise scenarios, 489 and 668 communities, respectively, would face effective inundation by the year 2100. With these two scenarios, more than half of communities facing effective inundation by 2045 contain areas of current high socioeconomic vulnerability. These results highlight the timeframes that US coastal communities have to respond to disruptive future inundation. The results also underscore the importance of limiting future warming and sea level rise: under the Intermediate-Low scenario, used as a proxy for sea level rise under the Paris Climate Agreement, 199 fewer communities would be effectively inundated by 2100.

THE USE OF LIDAR AND VOLUNTEERED GEOGRAPHIC INFORMATION TO MAP FLOOD EXTENTS AND INUNDATION

Directory of Open Access Journals (Sweden)

K. McDougall

2012-07-01

Full Text Available Floods are one of the most destructive natural disasters that threaten communities and properties. In recent decades, flooding has claimed more lives, destroyed more houses and ruined more agricultural land than any other natural hazard. The accurate prediction of the areas of inundation from flooding is critical to saving lives and property, but relies heavily on accurate digital elevation and hydrologic models. The 2011 Brisbane floods provided a unique opportunity to capture high resolution digital aerial imagery as the floods neared their peak, allowing the capture of areas of inundation over the various city suburbs. This high quality imagery, together with accurate LiDAR data over the area and publically available volunteered geographic imagery through repositories such as Flickr, enabled the reconstruction of flood extents and the assessment of both area and depth of inundation for the assessment of damage. In this study, approximately 20 images of flood damaged properties were utilised to identify the peak of the flood. Accurate position and height values were determined through the use of RTK GPS and conventional survey methods. This information was then utilised in conjunction with river gauge information to generate a digital flood surface. The LiDAR generated DEM was then intersected with the flood surface to reconstruct the area of inundation. The model determined areas of inundation were then compared to the mapped flood extent from the high resolution digital imagery to assess the accuracy of the process. The paper concludes that accurate flood extent prediction or mapping is possible through this method, although its accuracy is dependent on the number and location of sampled points. The utilisation of LiDAR generated DEMs and DSMs can also provide an excellent mechanism to estimate depths of inundation and hence flood damage

The Use of LIDAR and Volunteered Geographic Information to Map Flood Extents and Inundation

Science.gov (United States)

McDougall, K.; Temple-Watts, P.

2012-07-01

Floods are one of the most destructive natural disasters that threaten communities and properties. In recent decades, flooding has claimed more lives, destroyed more houses and ruined more agricultural land than any other natural hazard. The accurate prediction of the areas of inundation from flooding is critical to saving lives and property, but relies heavily on accurate digital elevation and hydrologic models. The 2011 Brisbane floods provided a unique opportunity to capture high resolution digital aerial imagery as the floods neared their peak, allowing the capture of areas of inundation over the various city suburbs. This high quality imagery, together with accurate LiDAR data over the area and publically available volunteered geographic imagery through repositories such as Flickr, enabled the reconstruction of flood extents and the assessment of both area and depth of inundation for the assessment of damage. In this study, approximately 20 images of flood damaged properties were utilised to identify the peak of the flood. Accurate position and height values were determined through the use of RTK GPS and conventional survey methods. This information was then utilised in conjunction with river gauge information to generate a digital flood surface. The LiDAR generated DEM was then intersected with the flood surface to reconstruct the area of inundation. The model determined areas of inundation were then compared to the mapped flood extent from the high resolution digital imagery to assess the accuracy of the process. The paper concludes that accurate flood extent prediction or mapping is possible through this method, although its accuracy is dependent on the number and location of sampled points. The utilisation of LiDAR generated DEMs and DSMs can also provide an excellent mechanism to estimate depths of inundation and hence flood damage

Effect of Nearshore Islands on Tsunami Inundation in Shadow Zones

Science.gov (United States)

Goertz, J.; Kaihatu, J. M.; Kalligeris, N.; Lynett, P. J.; Synolakis, C.

2017-12-01

Field surveys performed in the wake of the 2010 Mentawai tsunami event have described the belief of local residents that offshore islands serve as possible tsunami sheltering mechanisms, reducing the corresponding inundation on beaches behind the islands, despite the fact that deduced inundation from debris lines show this to be in fact untrue (Hill et al. 2012). Recent numerical model studies (Stefanakis et al. 2014) have shown that inundation levels on beaches behind conical islands are indeed higher than they are on open coastlines. While work has been done on tsunami amplification on the lee side of islands (Briggs et al. 1995), no work has been done concerning tsunami inundation on beach areas behind the islands. A series of experiments to address this were conducted in the Directional Wave Basin (DWB) at the O.H. Hinsdale Wave Research Laboratory at Oregon State University in summer 2016. A series of four sheet metal islands (two with a full conical section, two truncated at the water line) were placed at varying distances from the toe of a 1/10 sloping beach. Incident wave conditions consisting of solitary waves and full-stroke "dam break" waves were run over the islands. Free surface elevations, velocities, and beach runup were measured, with the intent of determining relationships between the wave condition, the island geometry and distance from the beach, and the tsunami characteristics. A series of runup measurements from a particular set of experiments can be seen in Figure 1. Based on these preliminary analyses, it was determined that: A) inundation was always amplified behind the island relative to areas outside this shadow zone; and B) inundation was generally highest with the island closest to the beach, except in the case where the tsunami wave broke prior to reaching the island. In this latter scenario, the inundation behind the island increased with island distance from the beach. The development of relationships between the inundation levels

Development of Probabilistic Flood Inundation Mapping For Flooding Induced by Dam Failure

Science.gov (United States)

Tsai, C.; Yeh, J. J. J.

2017-12-01

A primary function of flood inundation mapping is to forecast flood hazards and assess potential losses. However, uncertainties limit the reliability of inundation hazard assessments. Major sources of uncertainty should be taken into consideration by an optimal flood management strategy. This study focuses on the 20km reach downstream of the Shihmen Reservoir in Taiwan. A dam failure induced flood herein provides the upstream boundary conditions of flood routing. The two major sources of uncertainty that are considered in the hydraulic model and the flood inundation mapping herein are uncertainties in the dam break model and uncertainty of the roughness coefficient. The perturbance moment method is applied to a dam break model and the hydro system model to develop probabilistic flood inundation mapping. Various numbers of uncertain variables can be considered in these models and the variability of outputs can be quantified. The probabilistic flood inundation mapping for dam break induced floods can be developed with consideration of the variability of output using a commonly used HEC-RAS model. Different probabilistic flood inundation mappings are discussed and compared. Probabilistic flood inundation mappings are hoped to provide new physical insights in support of the evaluation of concerning reservoir flooded areas.

The Storm Surge and Sub-Grid Inundation Modeling in New York City during Hurricane Sandy

Directory of Open Access Journals (Sweden)

Harry V. Wang

2014-03-01

Full Text Available Hurricane Sandy inflicted heavy damage in New York City and the New Jersey coast as the second costliest storm in history. A large-scale, unstructured grid storm tide model, Semi-implicit Eulerian Lagrangian Finite Element (SELFE, was used to hindcast water level variation during Hurricane Sandy in the mid-Atlantic portion of the U.S. East Coast. The model was forced by eight tidal constituents at the model’s open boundary, 1500 km away from the coast, and the wind and pressure fields from atmospheric model Regional Atmospheric Modeling System (RAMS provided by Weatherflow Inc. The comparisons of the modeled storm tide with the NOAA gauge stations from Montauk, NY, Long Island Sound, encompassing New York Harbor, Atlantic City, NJ, to Duck, NC, were in good agreement, with an overall root mean square error and relative error in the order of 15–20 cm and 5%–7%, respectively. Furthermore, using large-scale model outputs as the boundary conditions, a separate sub-grid model that incorporates LIDAR data for the major portion of the New York City was also set up to investigate the detailed inundation process. The model results compared favorably with USGS’ Hurricane Sandy Mapper database in terms of its timing, local inundation area, and the depth of the flooding water. The street-level inundation with water bypassing the city building was created and the maximum extent of horizontal inundation was calculated, which was within 30 m of the data-derived estimate by USGS.

The morphological development of newly inundated intertidal areas: the mechanisms driving the early evolution of an estuarine environment designed and constructed by humans

Science.gov (United States)

Dale, Jonathan; Burgess, Heidi; Cundy, Andrew

2017-04-01

Intertidal saltmarsh and mudflat habitats are of global importance due to the ecosystem, economic and cultural services they provide. These services include wildlife habitat provision and species diversity, immobilisation of pollutants and protection from coastal flooding. Saltmarsh and mudflat environments are, however, being lost and degraded due to erosion caused by rising sea levels and increased storminess. These losses are exacerbated by anthropogenic influences including land reclamation, increased coastal development and the construction of coastal flood defences which prevent the landwards migration of saltmarsh and mudflat environments, resulting in coastal squeeze. To compensate for saltmarsh and mudflat losses areas of the coastal hinterland are being inundated by breaching defences and constructing new defences inland, thus extending or constructing new estuarine environments; a processes known as de-embankment or managed realignment. Morphological engineering and landscaping within managed realignment sites prior to site inundation varies depending on the aims of the scheme. However, there is a shortage of data on the morphological evolution within these sites post site inundation impeding the ability of coastal engineers to effectively design and construct future sites. To date there has been a focus on the colonisation of marine macro fauna and flora within newly inundated managed realignment sites, which can be relatively rapid and easily quantified. Little is known of the morphological evolution in response to altered sedimentary processes, its driving mechanisms and therefore the success and ecological sustainability of these sites. This study evaluates the post-inundation morphological development of the largest open coast managed realignment site in Europe, at Medmerry on the south coast of the United Kingdom. Inundated in September 2013, the Medmerry Managed Realignment Site consists of a mosaic of former agricultural land and areas of lower

Flood-inundation maps for the Tippecanoe River near Delphi, Indiana

Science.gov (United States)

Menke, Chad D.; Bunch, Aubrey R.; Kim, Moon H.

2013-01-01

Digital flood-inundation maps for an 11-mile reach of the Tippecanoe River that extends from County Road W725N to State Road 18 below Oakdale Dam, Indiana (Ind.), were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent of flooding corresponding to selected water levels (stages) at USGS streamgage 03333050, Tippecanoe River near Delphi, Ind. Current conditions at the USGS streamgages in Indiana may be obtained online at http://waterdata.usgs.gov/in/nwis/current/?type=flow. In addition, the information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system (http://water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that are often co-located at USGS streamgages. That forecasted peak-stage information, also available on the Internet, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, water-surface profiles were simulated for the stream reach by means of a hydraulic one-dimensional step-backwater model. The model was calibrated by using the most current stage-discharge relation at USGS streamgage 03333050, Tippecanoe River near Delphi, Ind., and USGS streamgage 03332605, Tippecanoe River below Oakdale Dam, Ind. The hydraulic model was then used to simulate 13 water-surface profiles for flood stages at 1-foot intervals reference to the streamgage datum and ranging from bankfull to approximately the highest recorded water level at the streamgage. The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from Light Detection and Ranging (LiDAR) data) in order to delineate the

Hydrodynamic and Inundation Modeling of China’s Largest Freshwater Lake Aided by Remote Sensing Data

Directory of Open Access Journals (Sweden)

Peng Zhang

2015-04-01

Full Text Available China’s largest freshwater lake, Poyang Lake, is characterized by rapid changes in its inundation area and hydrodynamics, so in this study, a hydrodynamic model of Poyang Lake was established to simulate these long-term changes. Inundation information was extracted from Moderate Resolution Imaging Spectroradiometer (MODIS remote sensing data and used to calibrate the wetting and drying parameter by assessing the accuracy of the simulated inundation area and its boundary. The bottom friction parameter was calibrated using current velocity measurements from Acoustic Doppler Current Profilers (ADCP. The results show the model is capable of predicting the inundation area dynamic through cross-validation with remotely sensed inundation data, and can reproduce the seasonal dynamics of the water level, and water discharge through a comparison with hydrological data. Based on the model results, the characteristics of the current velocities of the lake in the wet season and the dry season of the lake were explored, and the potential effect of the current dynamic on water quality patterns was discussed. The model is a promising basic tool for prediction and management of the water resource and water quality of Poyang Lake.

Trends in Playa Inundation and Water Storage in the Ogallala Aquifer on the Texas High Plains

Directory of Open Access Journals (Sweden)

Dennis Gitz

2016-08-01

Full Text Available The Ogallala Aquifer is an important source of irrigation water on the Texas High plains; however, significant decreases in saturated thickness threaten its future use for irrigation. A better understanding of the roles of playas, ephemeral surface ponds, in aquifer recharge is needed to establish levels of withdrawals that will meet either established desired future conditions or sustainability. In this study, data regarding playa inundation, depth to groundwater, precipitation and land cover from 2001 to 2011 were collected and analyzed to ascertain associations between these characteristics for four study areas on the Texas High plains. Each area covered 40,000–70,000 ha. Three of the study areas in Hockley, Floyd and Swisher counties were chosen because their center contained a playa instrumented to measure weather and depth of inundation. There were 20 distinct inundation events at the three instrumented playas between 2006 and 2010. For each of these inundations, water loss exceeded rates of potential evapotranspiration (ET by a factor of 1.6–15.7 times, implying that infiltration was occurring. Playa inundation in all four study areas was also assessed by analyzing images from the National Agricultural Imaginary program. Data on depth to groundwater were analyzed from 2000 to 2010 to determine annual changes of stored water. Annual changes in groundwater were weakly associated with surface area of inundated playas in late summer, but was strongly associated with annual rainfall. Rates of infiltration based on playa water loss versus potential ET, and volume of water in playas was more than sufficient to account for annual changes in groundwater. Land use adjoining the playas had less of influence on playa inundation than annual rainfall. These results strengthen the argument that water storage in playas on the Texas High Plains is an important source of water for aquifer recharge.

Flood-inundation maps for the Schoharie Creek at Prattsville, New York, 2014

Science.gov (United States)

Nystrom, Elizabeth A.

2016-02-18

Digital flood-inundation maps for a 2.6-mile reach of the Schoharie Creek at Prattsville, New York, were created by the U.S. Geological Survey (USGS) in cooperation with the New York State Department of Environmental Conservation. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at Schoharie Creek at Prattsville (station number 01350000). Near-real-time stages at this streamgage may be obtained online from the USGS National Water Information System (http://waterdata.usgs.gov/) or the National Weather Service Advanced Hydrologic Prediction Service (http://water.weather.gov/ahps/), which also forecasts flood hydrographs at this site. National Weather Service-forecasted peak-stage information may be used in conjunction with the maps developed in this study to show predicted areas and depths of flood inundation.

Tsunami risk assessment for facility group over a wide area using inundation assessment method considering energy conservation law

International Nuclear Information System (INIS)

Fukutani, Yo; Imamura, Fumihiko; Tokunaga, Takeshi; Sato, Ichiro

2015-01-01

We propose a quantitative evaluation method of overall tsunami risk that the entire facility group over a wide area holds. We considerably reduced the calculation cost for tsunami inundation depth by adopting the evaluation method using energy conservation law as compared with the evaluation method using non-linear long wave equation. For financial institutions such as banks and insurance companies with contractors over a wide area and business companies with multiple their assets and facilities in various places, the proposed evaluation method in this study could be a useful approach to implement their risk-based management decisions for tsunami risk. (author)

An evaluation of onshore digital elevation models for tsunami inundation modelling

Science.gov (United States)

Griffin, J.; Latief, H.; Kongko, W.; Harig, S.; Horspool, N.; Hanung, R.; Rojali, A.; Maher, N.; Fountain, L.; Fuchs, A.; Hossen, J.; Upi, S.; Dewanto, S. E.; Cummins, P. R.

2012-12-01

Tsunami inundation models provide fundamental information about coastal areas that may be inundated in the event of a tsunami along with additional parameters such as flow depth and velocity. This can inform disaster management activities including evacuation planning, impact and risk assessment and coastal engineering. A fundamental input to tsunami inundation models is adigital elevation model (DEM). Onshore DEMs vary widely in resolution, accuracy, availability and cost. A proper assessment of how the accuracy and resolution of DEMs translates into uncertainties in modelled inundation is needed to ensure results are appropriately interpreted and used. This assessment can in turn informdata acquisition strategies depending on the purpose of the inundation model. For example, lower accuracy elevation data may give inundation results that are sufficiently accurate to plan a community's evacuation route but not sufficient to inform engineering of a vertical evacuation shelters. A sensitivity study is undertaken to assess the utility of different available onshore digital elevation models for tsunami inundation modelling. We compare airborne interferometric synthetic aperture radar (IFSAR), ASTER and SRTM against high resolution (historical tsunami run-up data. Large vertical errors (> 10 m) and poor resolution of the coastline in the ASTER and SRTM elevation models cause modelled inundation to be much less compared with models using better data and with observations. Therefore we recommend that ASTER and SRTM should not be used for modelling tsunami inundation in order to determine tsunami extent or any other measure of onshore tsunami hazard. We suggest that for certain disaster management applications where the important factor is the extent of inundation, such as evacuation planning, airborne IFSAR provides a good compromise between cost and accuracy; however the representation of flow parameters such as depth and velocity is not sufficient to inform detailed

Evaluation of low impact development approach for mitigating flood inundation at a watershed scale in China.

Science.gov (United States)

Hu, Maochuan; Sayama, Takahiro; Zhang, Xingqi; Tanaka, Kenji; Takara, Kaoru; Yang, Hong

2017-05-15

Low impact development (LID) has attracted growing attention as an important approach for urban flood mitigation. Most studies evaluating LID performance for mitigating floods focus on the changes of peak flow and runoff volume. This paper assessed the performance of LID practices for mitigating flood inundation hazards as retrofitting technologies in an urbanized watershed in Nanjing, China. The findings indicate that LID practices are effective for flood inundation mitigation at the watershed scale, and especially for reducing inundated areas with a high flood hazard risk. Various scenarios of LID implementation levels can reduce total inundated areas by 2%-17% and areas with a high flood hazard level by 6%-80%. Permeable pavement shows better performance than rainwater harvesting against mitigating urban waterlogging. The most efficient scenario is combined rainwater harvesting on rooftops with a cistern capacity of 78.5 mm and permeable pavement installed on 75% of non-busy roads and other impervious surfaces. Inundation modeling is an effective approach to obtaining the information necessary to guide decision-making for designing LID practices at watershed scales. Copyright © 2017 Elsevier Ltd. All rights reserved.

Chronic Inundation along the US Coastline: Where, When and How to Respond

Science.gov (United States)

Caldas, A.; Dahl, K. A.; Spanger-Siegfried, E.; Udvardy, S.

2017-12-01

The Union of Concerned Scientists conducted an analysis of exposure to chronic inundation along the US coastline, using three localized sea level rise projections—Highest, Intermediate-High and Intermediate-Low—drawn from the 2014 National Climate Assessment. Chronic inundation is defined as flooding of 10 percent or more of usable land area at least 26 times per year. The goal of the analysis was to identify not only which communities would face this type of disruptive inundation, but also when, and over how much of their area. By having a timeframe and different scenarios, communities can prepare according to the time they have, and their tolerance for risk. We also used the Social Vulnerability Index (SoVI) at the Census tract level to identify which of these communities might be differentially impacted because of socioeconomic factors. We found that, by 2035, 170 communities will be facing chronic inundation. That number jumps to between 490 and 670 by the end of the century, depending on the scenario. Under the two higher scenarios, more than half of communities facing chronic inundation by 2035 contain tracts with high socioeconomic vulnerability today. Using the Intermediate-Low scenario as a proxy for sea level rise were the long-term temperature goals outlined in the Paris Climate Agreement were met, we found that up to 380 communities could avoid chronic inundation this century. The results are accessible within an interactive online tool, which zooms in to street level, therefore providing specific information that communities, city planners, and elected officials need to plan and prepare. Preparatory measures could include defending against the sea, accommodating and learning to live with water, or retreating from areas that are too hard to live in anymore. Each of these measures has challenges, and communities will need to adopt a portfolio of actions to prepare and protect themselves. Depending on their inundation response time, communities might

Hydrological and hydraulic models for determination of flood-prone and flood inundation areas

Science.gov (United States)

Aksoy, Hafzullah; Sadan Ozgur Kirca, Veysel; Burgan, Halil Ibrahim; Kellecioglu, Dorukhan

2016-05-01

Geographic Information Systems (GIS) are widely used in most studies on water resources. Especially, when the topography and geomorphology of study area are considered, GIS can ease the work load. Detailed data should be used in this kind of studies. Because of, either the complication of the models or the requirement of highly detailed data, model outputs can be obtained fast only with a good optimization. The aim in this study, firstly, is to determine flood-prone areas in a watershed by using a hydrological model considering two wetness indexes; the topographical wetness index, and the SAGA (System for Automated Geoscientific Analyses) wetness index. The wetness indexes were obtained in the Quantum GIS (QGIS) software by using the Digital Elevation Model of the study area. Flood-prone areas are determined by considering the wetness index maps of the watershed. As the second stage of this study, a hydraulic model, HEC-RAS, was executed to determine flood inundation areas under different return period-flood events. River network cross-sections required for this study were derived from highly detailed digital elevation models by QGIS. Also river hydraulic parameters were used in the hydraulic model. Modelling technology used in this study is made of freely available open source softwares. Based on case studies performed on watersheds in Turkey, it is concluded that results of such studies can be used for taking precaution measures against life and monetary losses due to floods in urban areas particularly.

Hydrological and hydraulic models for determination of flood-prone and flood inundation areas

Directory of Open Access Journals (Sweden)

H. Aksoy

2016-05-01

Full Text Available Geographic Information Systems (GIS are widely used in most studies on water resources. Especially, when the topography and geomorphology of study area are considered, GIS can ease the work load. Detailed data should be used in this kind of studies. Because of, either the complication of the models or the requirement of highly detailed data, model outputs can be obtained fast only with a good optimization. The aim in this study, firstly, is to determine flood-prone areas in a watershed by using a hydrological model considering two wetness indexes; the topographical wetness index, and the SAGA (System for Automated Geoscientific Analyses wetness index. The wetness indexes were obtained in the Quantum GIS (QGIS software by using the Digital Elevation Model of the study area. Flood-prone areas are determined by considering the wetness index maps of the watershed. As the second stage of this study, a hydraulic model, HEC-RAS, was executed to determine flood inundation areas under different return period-flood events. River network cross-sections required for this study were derived from highly detailed digital elevation models by QGIS. Also river hydraulic parameters were used in the hydraulic model. Modelling technology used in this study is made of freely available open source softwares. Based on case studies performed on watersheds in Turkey, it is concluded that results of such studies can be used for taking precaution measures against life and monetary losses due to floods in urban areas particularly.

Characteristics of peak streamflows and extent of inundation in areas of West Virginia and southwestern Virginia affected by flooding, June 2016

Science.gov (United States)

Austin, Samuel H.; Watson, Kara M.; Lotspeich, R. Russell; Cauller, Stephen J.; White , Jeremy S.; Wicklein, Shaun M.

2017-11-17

Heavy rainfall occurred across central and southern West Virginia in June 2016 as a result of repeated rounds of torrential thunderstorms. The storms caused major flooding and flash flooding in central and southern West Virginia with Kanawha, Fayette, Nicholas, and Greenbrier Counties among the hardest hit. Over the duration of the storms, from 8 to 9.37 inches of rain was reported in areas in Greenbrier County. Peak streamflows were the highest on record at 7 locations, and streamflows at 18 locations ranked in the top five for the period of record at U.S. Geological Survey streamflow-gaging stations used in this study. Following the storms, U.S. Geological Survey hydrographers identified and documented 422 high-water marks in West Virginia, noting location and height of the water above land surface. Many of these high-water marks were used to create flood-inundation maps for selected communities of West Virginia that experienced flooding in June 2016. Digital datasets of the inundation areas, mapping boundaries, and water depth rasters are available online.

Ensemble projection of the sea level rise impact on storm surge and inundation at the coast of Bangladesh

Science.gov (United States)

Jisan, Mansur Ali; Bao, Shaowu; Pietrafesa, Leonard J.

2018-01-01

The hydrodynamic model Delft3D is used to study the impact of sea level rise (SLR) on storm surge and inundation in the coastal region of Bangladesh. To study the present-day inundation scenario, the tracks of two known tropical cyclones (TC) were used: Aila (Category 1; 2009) and Sidr (Category 5; 2007). Model results were validated with the available observations. Future inundation scenarios were generated by using the strength of TC Sidr, TC Aila and an ensemble of historical TC tracks but incorporating the effect of SLR. Since future change in storm surge inundation under SLR impact is a probabilistic incident, a probable range of future change in the inundated area was calculated by taking into consideration the uncertainties associated with TC tracks, intensities and landfall timing. The model outputs showed that the inundated area for TC Sidr, which was calculated as 1860 km2, would become 31 % larger than the present-day scenario if a SLR of 0.26 m occurred during the mid-21st-century climate scenario. Similarly to that, an increasing trend was found for the end-21st-century climate scenario. It was found that with a SLR of 0.54 m, the inundated area would become 53 % larger than the present-day case. Along with the inundation area, the impact of SLR was examined for changes in future storm surge level. A significant increase of 14 % was found in storm surge level for the case of TC Sidr at Barisal station if a SLR of 0.26 m occurred in the mid-21st century. Similarly to that, an increase of 29 % was found at storm surge level with a SLR of 0.54 m in this location for the end-21st-century climate scenario. Ensemble projections based on uncertainties of future TC events also showed that, for a change of 0.54 m in SLR, the inundated area would range between 3500 and 3750 km2, whereas for present-day SLR simulations it was found within the range of 1000-1250 km2. These results revealed that even if the future TCs remain at the same strength as at present, the

Flood-inundation maps for the Wabash River at Lafayette, Indiana

Science.gov (United States)

Kim, Moon H.

2018-05-10

Digital flood-inundation maps for an approximately 4.8-mile reach of the Wabash River at Lafayette, Indiana (Ind.) were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Office of Community and Rural Affairs. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science web site at https://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at USGS streamgage 03335500, Wabash River at Lafayette, Ind. Current streamflow conditions for estimating near-real-time areas of inundation using USGS streamgage information may be obtained on the internet at https://waterdata.usgs.gov/in/nwis/uv?site_no=03335500. In addition, information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood-warning system (https://water.weather.gov/ahps/). The NWS AHPS forecasts flood hydrographs at many places that are often colocated with USGS streamgages, including the Wabash River at Lafayette, Ind. NWS AHPS-forecast peak-stage information may be used with the maps developed in this study to show predicted areas of flood inundation.For this study, flood profiles were computed for the Wabash River reach by means of a one-dimensional step-backwater model. The hydraulic model was calibrated by using the most current stage-discharge relations at USGS streamgage 03335500, Wabash River at Lafayette, Ind., and high-water marks from the flood of July 2003 (U.S. Army Corps of Engineers [USACE], 2007). The calibrated hydraulic model was then used to determine 23 water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datum and ranging from bankfull to the highest stage of the current stage-discharge rating curve. The simulated water-surface profiles were then combined with a geographic information system digital elevation model derived

Temporal changes of radioactive contamination of Ploučnice river Inundation area, Czech Republic

International Nuclear Information System (INIS)

Neznal, M.; Gnojek, I.; Thinová, L.; Neubauer, L.

2010-01-01

The inundation area of Ploučnice river has been contaminated by natural radionuclides during the early mining of the uranium ore deposit in the region of Stráž pod Ralskem, Northern Bohemia, i.e. in the seventies and in the eighties of the last century. The evaluation of the level of contamination has faced many problems. During several floods that occurred after the primary contamination, the contaminants were spread to a relatively large territory, but the level of contamination became fairly variable. Large regions have not been affected at all, and measured values of gamma dose rate are comparable with the values of natural background. On the other hand, a higher contamination can be found at small areas, often situated far from the river - for example in catchwater drains. Moreover, many contaminated areas are located in places that are difficult to reach. The topographical orientation is also intricate in such places. A study of temporal changes of contamination was based on a comparison of data obtained using two different methods: airborne gamma-ray spectrometry and detailed ground gamma dose rate and in situ gamma spectrometry measurements

Dynamic inundation mapping of Hurricane Harvey flooding in the Houston metro area using hyper-resolution modeling and quantitative image reanalysis

Science.gov (United States)

Noh, S. J.; Lee, J. H.; Lee, S.; Zhang, Y.; Seo, D. J.

2017-12-01

Hurricane Harvey was one of the most extreme weather events in Texas history and left significant damages in the Houston and adjoining coastal areas. To understand better the relative impact to urban flooding of extreme amount and spatial extent of rainfall, unique geography, land use and storm surge, high-resolution water modeling is necessary such that natural and man-made components are fully resolved. In this presentation, we reconstruct spatiotemporal evolution of inundation during Hurricane Harvey using hyper-resolution modeling and quantitative image reanalysis. The two-dimensional urban flood model used is based on dynamic wave approximation and 10 m-resolution terrain data, and is forced by the radar-based multisensor quantitative precipitation estimates. The model domain includes Buffalo, Brays, Greens and White Oak Bayous in Houston. The model is simulated using hybrid parallel computing. To evaluate dynamic inundation mapping, we combine various qualitative crowdsourced images and video footages with LiDAR-based terrain data.

Automated quantification of surface water inundation in wetlands using optical satellite imagery

Science.gov (United States)

DeVries, Ben; Huang, Chengquan; Lang, Megan W.; Jones, John W.; Huang, Wenli; Creed, Irena F.; Carroll, Mark L.

2017-01-01

We present a fully automated and scalable algorithm for quantifying surface water inundation in wetlands. Requiring no external training data, our algorithm estimates sub-pixel water fraction (SWF) over large areas and long time periods using Landsat data. We tested our SWF algorithm over three wetland sites across North America, including the Prairie Pothole Region, the Delmarva Peninsula and the Everglades, representing a gradient of inundation and vegetation conditions. We estimated SWF at 30-m resolution with accuracies ranging from a normalized root-mean-square-error of 0.11 to 0.19 when compared with various high-resolution ground and airborne datasets. SWF estimates were more sensitive to subtle inundated features compared to previously published surface water datasets, accurately depicting water bodies, large heterogeneously inundated surfaces, narrow water courses and canopy-covered water features. Despite this enhanced sensitivity, several sources of errors affected SWF estimates, including emergent or floating vegetation and forest canopies, shadows from topographic features, urban structures and unmasked clouds. The automated algorithm described in this article allows for the production of high temporal resolution wetland inundation data products to support a broad range of applications.

Effects on the upstream flood inundation caused from the operation of Chao Phraya Dam

Directory of Open Access Journals (Sweden)

Sutham Visutimeteegorn

2007-11-01

Full Text Available During the flooding events, the operation of Chao Phraya Dam to control downstream water discharge is one of the causes of the inundation occuring over the upstream area. The purposes of this research are to study the effects of the operation of Chao Phraya Dam upon the upstream flood inundation and to find out the new measures of the flood mitigation in the upstream areas of Chao Phraya Dam by using a hydrodynamic model. The results show that Manning's n in the Chao Phraya River and its tributaries is 0.030-0.035 in the main channels and 0.050-0.070 in the flood plain areas. The backwater due to the operation of the Chao Praya dam affects as far as 110 kilometers upstream. New methods of water diversion can mitigate the flood inundation without the effect on the floating rice fields. The construction of reservoirs in the Upper Sakaekang River Basin and the Upper Yom River Basin will mitigate the flood not only in their own basins but also in the Lower Chao Phraya River Basin. The coordinated operation of the Chao Phraya Dam, the regulators and the upper basin reservoirs will efficiently mitigate the flood inundation.

a Novel Methodology for Developing Inundation Maps Under Climate Change Scenarios Using One-Dimensional Model

Science.gov (United States)

Vu, M. T.; Liong, S. Y.; Raghavan, V. S.; Liew, S. C.

2011-07-01

Climate change is expected to cause increases in extreme climatic events such as heavy rainstorms and rising tidal level. Heavy rainstorms are known to be serious causes of flooding problems in big cities. Thus, high density residential and commercial areas along the rivers are facing risks of being flooded. For that reason, inundated area determination is now being considered as one of the most important areas of research focus in flood forecasting. In such a context, this paper presents the development of a floodmap in determining flood-prone areas and its volumes. The areas and volumes of flood are computed by the inundated level using the existing digital elevation model (DEM) of a hypothetical catchment chosen for study. The study focuses on the application of Flood Early Warning System (Delft — FEWS, Deltares), which is designated to work with the SOBEK (Delft) to simulate the extent of stormwater on the ground surface. The results from FEWS consist of time-series of inundation maps in Image file format (PNG) and ASCII format, which are subsequently imported to ArcGIS for further calculations. In addition, FEWS results provide options to export the video clip of water spreading out over the catchment. Consequently, inundated area and volume will be determined by the water level on the ground. Final floodmap is displayed in colors created by ArcGIS. Various flood map results corresponding to climate change scenarios will be displayed in the main part of the paper.

A New Rapid Simplified Model for Urban Rainstorm Inundation with Low Data Requirements

Directory of Open Access Journals (Sweden)

Ji Shen

2016-11-01

Full Text Available This paper proposes a new rapid simplified inundation model (NRSIM for flood inundation caused by rainstorms in an urban setting that can simulate the urban rainstorm inundation extent and depth in a data-scarce area. Drainage basins delineated from a floodplain map according to the distribution of the inundation sources serve as the calculation cells of NRSIM. To reduce data requirements and computational costs of the model, the internal topography of each calculation cell is simplified to a circular cone, and a mass conservation equation based on a volume spreading algorithm is established to simulate the interior water filling process. Moreover, an improved D8 algorithm is outlined for the simulation of water spilling between different cells. The performance of NRSIM is evaluated by comparing the simulated results with those from a traditional rapid flood spreading model (TRFSM for various resolutions of digital elevation model (DEM data. The results are as follows: (1 given high-resolution DEM data input, the TRFSM model has better performance in terms of precision than NRSIM; (2 the results from TRFSM are seriously affected by the decrease in DEM data resolution, whereas those from NRSIM are not; and (3 NRSIM always requires less computational time than TRFSM. Apparently, compared with the complex hydrodynamic or traditional rapid flood spreading model, NRSIM has much better applicability and cost-efficiency in real-time urban inundation forecasting for data-sparse areas.

Flood-inundation maps for the Susquehanna River near Harrisburg, Pennsylvania, 2013

Science.gov (United States)

Roland, Mark A.; Underwood, Stacey M.; Thomas, Craig M.; Miller, Jason F.; Pratt, Benjamin A.; Hogan, Laurie G.; Wnek, Patricia A.

2014-01-01

A series of 28 digital flood-inundation maps was developed for an approximate 25-mile reach of the Susquehanna River in the vicinity of Harrisburg, Pennsylvania. The study was selected by the U.S. Army Corps of Engineers (USACE) national Silver Jackets program, which supports interagency teams at the state level to coordinate and collaborate on flood-risk management. This study to produce flood-inundation maps was the result of a collaborative effort between the USACE, National Weather Service (NWS), Susquehanna River Basin Commission (SRBC), The Harrisburg Authority, and the U.S. Geological Survey (USGS). These maps are accessible through Web-mapping applications associated with the NWS, SRBC, and USGS. The maps can be used in conjunction with the real-time stage data from the USGS streamgage 01570500, Susquehanna River at Harrisburg, Pa., and NWS flood-stage forecasts to help guide the general public in taking individual safety precautions and will provide local municipal officials with a tool to efficiently manage emergency flood operations and flood mitigation efforts. The maps were developed using the USACE HEC–RAS and HEC–GeoRAS programs to compute water-surface profiles and to delineate estimated flood-inundation areas for selected stream stages. The maps show estimated flood-inundation areas overlaid on high-resolution, georeferenced, aerial photographs of the study area for stream stages at 1-foot intervals between 11 feet and 37 feet (which include NWS flood categories Action, Flood, Moderate, and Major) and the June 24, 1972, peak-of-record flood event at a stage of 33.27 feet at the Susquehanna River at Harrisburg, Pa., streamgage.

Flood-inundation maps for the St. Marys River at Fort Wayne, Indiana

Science.gov (United States)

Menke, Chad D.; Kim, Moon H.; Fowler, Kathleen K.

2012-01-01

Digital flood-inundation maps for a 9-mile reach of the St. Marys River that extends from South Anthony Boulevard to Main Street at Fort Wayne, Indiana, were created by the U.S. Geological Survey (USGS) in cooperation with the City of Fort Wayne. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site, depict estimates of the areal extent of flooding corresponding to selected water levels (stages) at the USGS streamgage 04182000 St. Marys River near Fort Wayne, Ind. Current conditions at the USGS streamgages in Indiana may be obtained from the National Water Information System: Web Interface. In addition, the information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system. The NWS forecasts flood hydrographs at many places that are often collocated at USGS streamgages. That forecasted peak-stage information, also available on the Internet, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, water-surface profiles were simulated for the stream reach by means of a hydraulic one-dimensional step-backwater model. The model was calibrated using the most current stage-discharge relation at the USGS streamgage 04182000 St. Marys River near Fort Wayne, Ind. The hydraulic model was then used to simulate 11 water-surface profiles for flood stages at 1-ft intervals referenced to the streamgage datum and ranging from bankfull to approximately the highest recorded water level at the streamgage. The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from Light Detection and Ranging (LiDAR) data) in order to delineate the area flooded at each water level. A flood inundation map was generated for each water-surface profile stage (11 maps in all) so that for any given flood stage users will be

Inundation Analysis of Reservoir Flood Based on Computer Aided Design (CAD and Digital Elevation Model (DEM

Directory of Open Access Journals (Sweden)

Jiqing Li

2018-04-01

Full Text Available GIS (Geographic Information System can be used to combine multiple hydrologic data and geographic data for FIA (Flood Impact Assessment. For a developing country like China, a lot of geographic data is in the CAD (Computer Aided Design format. The commonly used method for converting CAD into DEM may result in data loss. This paper introduces a solution for the conversion between CAD data and DEM data. The method has been applied to the FIA based on the topographic map of CAD in Hanjiang River. When compared with the other method, the new method solves the data loss problem. Besides, the paper use GIS to simulate the inundation range, area, and the depth distribution of flood backwater. Based on the analysis, the author concludes: (1 the differences of the inundation areas between the flood of HQ100 and the flood of HQ50 are small. (2 The inundation depth shows a decreasing trend along the upstream of the river. (3 The inundation area less than 4 m in flood of HQ50 is larger than that in flood of HQ100, the result is opposite when the inundation depth is greater than 4 m. (4 The flood loss is 392.32 million RMB for flood of HQ50 and 610.02 million RMB for flood of HQ100. The method can be applied to FIA.

Probabilistic storm surge inundation maps for Metro Manila based on Philippine public storm warning signals

Science.gov (United States)

Tablazon, J.; Caro, C. V.; Lagmay, A. M. F.; Briones, J. B. L.; Dasallas, L.; Lapidez, J. P.; Santiago, J.; Suarez, J. K.; Ladiero, C.; Gonzalo, L. A.; Mungcal, M. T. F.; Malano, V.

2015-03-01

A storm surge is the sudden rise of sea water over the astronomical tides, generated by an approaching storm. This event poses a major threat to the Philippine coastal areas, as manifested by Typhoon Haiyan on 8 November 2013. This hydro-meteorological hazard is one of the main reasons for the high number of casualties due to the typhoon, with 6300 deaths. It became evident that the need to develop a storm surge inundation map is of utmost importance. To develop these maps, the Nationwide Operational Assessment of Hazards under the Department of Science and Technology (DOST-Project NOAH) simulated historical tropical cyclones that entered the Philippine Area of Responsibility. The Japan Meteorological Agency storm surge model was used to simulate storm surge heights. The frequency distribution of the maximum storm surge heights was calculated using simulation results of tropical cyclones under a specific public storm warning signal (PSWS) that passed through a particular coastal area. This determines the storm surge height corresponding to a given probability of occurrence. The storm surge heights from the model were added to the maximum astronomical tide data from WXTide software. The team then created maps of inundation for a specific PSWS using the probability of exceedance derived from the frequency distribution. Buildings and other structures were assigned a probability of exceedance depending on their occupancy category, i.e., 1% probability of exceedance for critical facilities, 10% probability of exceedance for special occupancy structures, and 25% for standard occupancy and miscellaneous structures. The maps produced show the storm-surge-vulnerable areas in Metro Manila, illustrated by the flood depth of up to 4 m and extent of up to 6.5 km from the coastline. This information can help local government units in developing early warning systems, disaster preparedness and mitigation plans, vulnerability assessments, risk-sensitive land use plans, shoreline

Determination of minimum flood flow for regeneration of floodplain forest from inundated forest width-stage curve

Directory of Open Access Journals (Sweden)

Song-hao Shang

2010-09-01

Full Text Available Floods are essential for the regeneration and growth of floodplain forests in arid and semiarid regions. However, river flows, and especially flood flows, have decreased greatly with the increase of water diversion from rivers and/or reservoir regulation, resulting in severe deterioration of floodplain ecosystems. Estimation of the flood stage that will inundate the floodplain forest is necessary for the forest's restoration or protection. To balance water use for economic purposes and floodplain forest protection, the inundated forest width method is proposed for estimating the minimum flood stage for floodplain forests from the inundated forest width-stage curve. The minimum flood stage is defined as the breakpoint of the inundated forest width-stage curve, and is determined directly or analytically from the curve. For the analytical approach, the problem under consideration is described by a multi-objective optimization model, which can be solved by the ideal point method. Then, the flood flow at the minimum flood stage (minimum flood flow, which is useful for flow regulation, can be calculated from the stage-discharge curve. In order to protect the forest in a river floodplain in a semiarid area in Xinjiang subject to reservoir regulation upstream, the proposed method was used to determine the minimum flood stage and flow for the forest. Field survey of hydrology, topography, and forest distribution was carried out at typical cross sections in the floodplain. Based on the survey results, minimum flood flows for six typical cross sections were estimated to be between 306 m3/s and 393 m3/s. Their maximum, 393 m3/s, was considered the minimum flood flow for the study river reach. This provides an appropriate flood flow for the protection of floodplain forest and can be used in the regulation of the upstream reservoir.

A satellite and model based flood inundation climatology of Australia

Science.gov (United States)

Schumann, G.; Andreadis, K.; Castillo, C. J.

2013-12-01

To date there is no coherent and consistent database on observed or simulated flood event inundation and magnitude at large scales (continental to global). The only compiled data set showing a consistent history of flood inundation area and extent at a near global scale is provided by the MODIS-based Dartmouth Flood Observatory. However, MODIS satellite imagery is only available from 2000 and is hampered by a number of issues associated with flood mapping using optical images (e.g. classification algorithms, cloud cover, vegetation). Here, we present for the first time a proof-of-concept study in which we employ a computationally efficient 2-D hydrodynamic model (LISFLOOD-FP) complemented with a sub-grid channel formulation to generate a complete flood inundation climatology of the past 40 years (1973-2012) for the entire Australian continent. The model was built completely from freely available SRTM-derived data, including channel widths, bank heights and floodplain topography, which was corrected for vegetation canopy height using a global ICESat canopy dataset. Channel hydraulics were resolved using actual channel data and bathymetry was estimated within the model using hydraulic geometry. On the floodplain, the model simulated the flow paths and inundation variables at a 1 km resolution. The developed model was run over a period of 40 years and a floodplain inundation climatology was generated and compared to satellite flood event observations. Our proof-of-concept study demonstrates that this type of model can reliably simulate past flood events with reasonable accuracies both in time and space. The Australian model was forced with both observed flow climatology and VIC-simulated flows in order to assess the feasibility of a model-based flood inundation climatology at the global scale.

Developing an early warning system for storm surge inundation in the Philippines

Science.gov (United States)

Tablazon, J.; Caro, C. V.; Lagmay, A. M. F.; Briones, J. B. L.; Dasallas, L.; Lapidez, J. P.; Santiago, J.; Suarez, J. K.; Ladiero, C.; Gonzalo, L. A.; Mungcal, M. T. F.; Malano, V.

2014-10-01

A storm surge is the sudden rise of sea water generated by an approaching storm, over and above the astronomical tides. This event imposes a major threat in the Philippine coastal areas, as manifested by Typhoon Haiyan on 8 November 2013 where more than 6000 people lost their lives. It has become evident that the need to develop an early warning system for storm surges is of utmost importance. To provide forecasts of the possible storm surge heights of an approaching typhoon, the Nationwide Operational Assessment of Hazards under the Department of Science and Technology (DOST-Project NOAH) simulated historical tropical cyclones that entered the Philippine Area of Responsibility. Bathymetric data, storm track, central atmospheric pressure, and maximum wind speed were used as parameters for the Japan Meteorological Agency Storm Surge Model. The researchers calculated the frequency distribution of maximum storm surge heights of all typhoons under a specific Public Storm Warning Signal (PSWS) that passed through a particular coastal area. This determines the storm surge height corresponding to a given probability of occurrence. The storm surge heights from the model were added to the maximum astronomical tide data from WXTide software. The team then created maps of probable area inundation and flood levels of storm surges along coastal areas for a specific PSWS using the results of the frequency distribution. These maps were developed from the time series data of the storm tide at 10 min intervals of all observation points in the Philippines. This information will be beneficial in developing early warnings systems, static maps, disaster mitigation and preparedness plans, vulnerability assessments, risk-sensitive land use plans, shoreline defense efforts, and coastal protection measures. Moreover, these will support the local government units' mandate to raise public awareness, disseminate information about storm surge hazards, and implement appropriate counter

Modeling Flood Inundation Induced by River Flow and Storm Surges over a River Basin

Directory of Open Access Journals (Sweden)

Wei-Bo Chen

2014-10-01

Full Text Available Low-lying coastal regions and their populations are at risk during storm surge events and high freshwater discharges from upriver. An integrated storm surge and flood inundation modeling system was used to simulate storm surge and inundation in the Tsengwen River basin and the adjacent coastal area in southern Taiwan. A three-dimensional hydrodynamic model with an unstructured grid was used, which was driven by the tidal elevation at the open boundaries and freshwater discharge at the upriver boundary. The model was validated against the observed water levels for three typhoon events. The simulation results for the model were in reasonable agreement with the observational data. The model was then applied to investigate the effects of a storm surge, freshwater discharge, and a storm surge combined with freshwater discharge during an extreme typhoon event. The super Typhoon Haiyan (2013 was artificially shifted to hit Taiwan: the modeling results showed that the inundation area and depth would cause severe overbank flow and coastal flooding for a 200 year return period flow. A high-resolution grid model is essential for the accurate simulation of storm surges and inundation.

Flood Inundation Mapping and Management using RISAT-1 derived Flood Inundation Areas, Cartosat-1 DEM and a River Flow Model

Science.gov (United States)

Kuldeep, K.; Garg, P. K.; Garg, R. D.

2017-12-01

The frequent occurrence of repeated flood events in many regions of the world causing damage to human life and property has augmented the need for effective flood risk management. Microwave satellite data is becoming an indispensable asset for monitoring of many environmental and climatic applications as numerous space-borne synthetic aperture radar (SAR) sensors are offering the data with high spatial resolutions and multi-polarization capabilities. The implementation and execution of Flood mapping, monitoring and management applications has become easier with the availability of SAR data which has obvious advantages over optical data due to its all weather, day and night capabilities. In this study, the exploitation of the SAR dataset for hydraulic modelling and disaster management has been highlighted using feature extraction techniques for water area identification and water level extraction within the floodplain. The availability of high precision digital elevation model generated from the Cartosat-1 stereo pairs has enhanced the capability of retrieving the water depth maps by incorporating the SAR derived flood extent maps. This paper illustrates the flood event on June 2013 in Yamuna River, Haryana, India. The water surface profile computed by combining the topographic data with the RISAT-1 data accurately reflects the true water line. Water levels that were computed by carrying out the modelling using hydraulic model in HECRAS also suggest that the water surface profiles provided by the combined use of topographic data and SAR accurately reflect the true water line. The proposed approach has also been found better in extraction of inundation within vegetated areas.

Flood Inundation Mapping and Emergency Operations during Hurricane Harvey

Science.gov (United States)

Fang, N. Z.; Cotter, J.; Gao, S.; Bedient, P. B.; Yung, A.; Penland, C.

2017-12-01

Hurricane Harvey struck the Gulf Coast as Category 4 on August 25, 2017 with devastating and life-threatening floods in Texas. Harris County received up to 49 inches of rainfall over a 5-day period and experienced flooding level and impacts beyond any previous storm in Houston's history. The depth-duration-frequency analysis reveals that the areal average rainfall for Brays Bayou surpasses the 500-year rainfall in both 24 and 48 hours. To cope with this unprecedented event, the researchers at the University of Texas at Arlington and Rice University worked closely with the U.S. Army Corps of Engineers (USACE), the National Weather Service (NWS), the Texas Division of Emergency Management (TDEM), Walter P. Moore and Associates, Inc. and Halff Associates, to conduct a series of meteorological, hydrologic and hydraulic analyses to delineate flood inundation maps. Up to eight major watersheds in Harris County were delineated based the available QPE data from WGRFC. The inundation map over Brays Bayou with their impacts from Hurricane Harvey was delineated in comparison with those of 100-, 500-year, and Probable Maximum Precipitation (PMP) design storms. This presentation will provide insights for both engineers and planners to re-evaluate the existing flood infrastructure and policy, which will help build Houston stronger for future extreme storms. The collaborative effort among the federal, academic, and private entities clearly demonstrates an effective approach for flood inundation mapping initiatives for the nation.

Hydrodynamic forces on inundated bridge decks

Science.gov (United States)

2009-05-01

The hydrodynamic forces experienced by an inundated bridge deck have great importance in the design of bridges. Specifically, the drag force, lift force, and the moment acting on the bridge deck under various levels of inundation and a range of flow ...

Spatial and temporal controls of atoll island inundation: implications for urbanized atolls in the Marshall Islands.

Science.gov (United States)

Ford, M.; Becker, J. M.; Merrifield, M. A.

2012-12-01

Atoll islands are highly vulnerable to a range of inundation hazards. The impacts of such hazards are expected to be magnified as a result of continued sea-level rise. Both recent and historic inundation events provide unique insights into the requisite conditions necessary to initiate island inundation. A number of recent and historic inundation events are presented in order to examine the oceanographic and meteorological conditions driving inundation of a densely populated, urbanized atoll in the central Pacific. Analysis of inundation events suggests that a number of key drivers contribute to the spatial and temporal extent of island inundation, with unique degrees of predictability and resultant impact signatures apparent on island geomorphology and local anthropogenic activities. Results indicate three distinct drivers of inundation hazards exist. Firstly, tropical storms and typhoons elevate sea level through inverse barometric setup, wind setup and a range of wave driven processes and have caused considerable impact on atolls within the Marshall Islands. Secondly, super-elevated sea level conditions resulting from the combination of seasonal high tides and quasi-cyclical La Nina conditions drive inundation of low-lying lagoon facing coastal areas. Thirdly, long period swell conditions, typically generated by distant storms, can elevate reef-flat water levels through wave setup and infragravity wave oscillations. Such wave conditions can over wash the ocean-facing island ridge, often inundating large sections of the island. Reef-flat wave conditions are tidally modulated, with inundation events typically occurring around high tide. However, the two most recent destructive swell-driven inundation events have occurred while tide levels were significantly lower than spring tide levels, suggesting high water levels are not a necessary prerequisite for wave-driven inundation. The different modes of inundation are discussed and grounded within recent and historic

Predicting Near Real-Time Inundation Occurrence from Complimentary Satellite Microwave Brightness Temperature Observations

Science.gov (United States)

Fisher, C. K.; Pan, M.; Wood, E. F.

2017-12-01

Throughout the world, there is an increasing need for new methods and data that can aid decision makers, emergency responders and scientists in the monitoring of flood events as they happen. In many regions, it is possible to examine the extent of historical and real-time inundation occurrence from visible and infrared imagery provided by sensors such as MODIS or the Landsat TM; however, this is not possible in regions that are densely vegetated or are under persistent cloud cover. In addition, there is often a temporal mismatch between the sampling of a particular sensor and a given flood event, leading to limited observations in near real-time. As a result, there is a need for alternative methods that take full advantage of complimentary remotely sensed data sources, such as available microwave brightness temperature observations (e.g., SMAP, SMOS, AMSR2, AMSR-E, and GMI), to aid in the estimation of global flooding. The objective of this work was to develop a high-resolution mapping of inundated areas derived from multiple satellite microwave sensor observations with a daily temporal resolution. This system consists of first retrieving water fractions from complimentary microwave sensors (AMSR-2 and SMAP) which may spatially and temporally overlap in the region of interest. Using additional information in a Random Forest classifier, including high resolution topography and multiple datasets of inundated area (both historical and empirical), the resulting retrievals are spatially downscaled to derive estimates of the extent of inundation at a scale relevant to management and flood response activities ( 90m or better) instead of the relatively coarse resolution water fractions, which are limited by the microwave sensor footprints ( 5-50km). Here we present the training and validation of this method for the 2015 floods that occurred in Houston, Texas. Comparing the predicted inundation against historical occurrence maps derived from the Landsat TM record and MODIS

Flood-inundation maps for a 9.1-mile reach of the Coast Fork Willamette River near Creswell and Goshen, Lane County, Oregon

Science.gov (United States)

Hess, Glen W.; Haluska, Tana L.

2016-04-13

Digital flood-inundation maps for a 9.1-mile reach of the Coast Fork Willamette River near Creswell and Goshen, Oregon, were developed by the U.S. Geological Survey (USGS) in cooperation with the U.S. Army Corps of Engineers (USACE). The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected stages at the USGS streamgage at Coast Fork Willamette River near Goshen, Oregon (14157500), at State Highway 58. Current stage at the streamgage for estimating near-real-time areas of inundation may be obtained at http://waterdata.usgs.gov/or/nwis/uv/?site_no=14157500&PARAmeter_cd=00065,00060. In addition, the National Weather Service (NWS) forecasted peak-stage information may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation.In this study, areas of inundation were provided by USACE. The inundated areas were developed from flood profiles simulated by a one-dimensional unsteady step‑backwater hydraulic model. The profiles were checked by the USACE using documented high-water marks from a January 2006 flood. The model was compared and quality assured using several other methods. The hydraulic model was then used to determine eight water-surface profiles at various flood stages referenced to the streamgage datum and ranging from 11.8 to 19.8 ft, approximately 2.6 ft above the highest recorded stage at the streamgage (17.17 ft) since 1950. The intervals between stages are variable and based on annual exceedance probability discharges, some of which approximate NWS action stages.The areas of inundation and water depth grids provided to USGS by USACE were used to create interactive flood‑inundation maps. The availability of these maps with current stage from USGS streamgage and forecasted stream stages from the NWS provide emergency management

Flood-inundation maps for the North Branch Elkhart River at Cosperville, Indiana

Science.gov (United States)

Kim, Moon H.; Johnson, Esther M.

2014-01-01

Digital flood-inundation maps for a reach of the North Branch Elkhart River at Cosperville, Indiana (Ind.), were created by the U.S. Geological Survey (USGS) in cooperation with the U.S. Army Corps of Engineers, Detroit District. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at USGS streamgage 04100222, North Branch Elkhart River at Cosperville, Ind. Current conditions for estimating near-real-time areas of inundation using USGS streamgage information may be obtained on the Internet at http://waterdata.usgs.gov/in/nwis/uv?site_no=04100222. In addition, information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system (http:/water.weather.gov/ahps/). The NWS AHPS forecasts flood hydrographs at many places that are often colocated with USGS streamgages, including the North Branch Elkhart River at Cosperville, Ind. NWS AHPS-forecast peak-stage information may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. For this study, flood profiles were computed for the North Branch Elkhart River reach by means of a one-dimensional step-backwater model. The hydraulic model was calibrated by using the most current stage-discharge relations at USGS streamgage 04100222, North Branch Elkhart River at Cosperville, Ind., and preliminary high-water marks from the flood of March 1982. The calibrated hydraulic model was then used to determine four water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datum and ranging from bankfull to the highest stage of the current stage-discharge rating curve. The simulated water-surface profiles were then combined with a geographic information system (GIS

Flood-inundation maps for the East Fork White River near Bedford, Indiana

Science.gov (United States)

Fowler, Kathleen K.

2014-01-01

Digital flood-inundation maps for an 1.8-mile reach of the East Fork White River near Bedford, Indiana (Ind.) were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ depict estimates of the areal extent and depth of flooding corresponding to selectedwater levels (stages) at USGS streamgage 03371500, East Fork White River near Bedford, Ind. Current conditions for estimating near-real-time areas of inundation using USGS streamgage information may be obtained on the Internet at http://waterdata.usgs.gov/in/nwis/uv?site_no=03371500. In addition, information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system (http://water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that are often colocated with USGS streamgages, including the East Fork White River near Bedford, Ind. NWS-forecasted peak-stage information may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. For this study, flood profiles were computed for the East Fork White River reach by means of a one-dimensional step-backwater model. The hydraulic model was calibrated by using the most current stage-discharge relations at USGS streamgage 03371500, East Fork White River near Bedford, Ind., and documented high-water marks from the flood of June 2008. The calibrated hydraulic model was then used to determine 20 water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datum and ranging from bankfull to the highest stage of the current stage-discharge rating curve. The simulated water-surface profiles were then combined with a geographic information system (GIS) digital elevation model (DEM, derived from

An expanded model: flood-inundation maps for the Leaf River at Hattiesburg, Mississippi, 2013

Science.gov (United States)

Storm, John B.

2014-01-01

Digital flood-inundation maps for a 6.8-mile reach of the Leaf River at Hattiesburg, Mississippi (Miss.), were created by the U.S. Geological Survey (USGS) in cooperation with the City of Hattiesburg, City of Petal, Forrest County, Mississippi Emergency Management Agency, Mississippi Department of Homeland Security, and the Emergency Management District. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at Leaf River at Hattiesburg, Miss. (station no. 02473000). Current conditions for estimating near-real-time areas of inundation by use of USGS streamgage information may be obtained on the Internet at http://waterdata.usgs.gov/. In addition, the information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system (http://water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that are often colocated with USGS streamgages. NWS-forecasted peak-stage information may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated by using the most current stage-discharge relations at the Leaf River at Hattiesburg, Miss. streamgage (02473000) and documented high-water marks from recent and historical floods. The hydraulic model was then used to determine 13 water-surface profiles for flood stages at 1.0-foot intervals referenced to the streamgage datum and ranging from bankfull to approximately the highest recorded water level at the streamgage. The simulated water-surface profiles were then combined with a geographic information system (GIS

Estimates of future inundation of salt marshes in response to sea-level rise in and around Acadia National Park, Maine

Science.gov (United States)

Nielsen, Martha G.; Dudley, Robert W.

2013-01-01

Salt marshes are ecosystems that provide many important ecological functions in the Gulf of Maine. The U.S. Geological Survey investigated salt marshes in and around Acadia National Park from Penobscot Bay to the Schoodic Peninsula to map the potential for landward migration of marshes using a static inundation model of a sea-level rise scenario of 60 centimeters (cm; 2 feet). The resulting inundation contours can be used by resource managers to proactively adapt to sea-level rise by identifying and targeting low-lying coastal areas adjacent to salt marshes for conservation or further investigation, and to identify risks to infrastructure in the coastal zone. For this study, the mapping of static inundation was based on digital elevation models derived from light detection and ranging (LiDAR) topographic data collected in October 2010. Land-surveyed control points were used to evaluate the accuracy of the LiDAR data in the study area, yielding a root mean square error of 11.3 cm. An independent accuracy assessment of the LiDAR data specific to salt-marsh land surfaces indicated a root mean square error of 13.3 cm and 95-percent confidence interval of ± 26.0 cm. LiDAR-derived digital elevation models and digital color aerial photography, taken during low tide conditions in 2008, with a pixel resolution of 0.5 meters, were used to identify the highest elevation of the land surface at each salt marsh in the study area. Inundation contours for 60-cm of sea-level rise were delineated above the highest marsh elevation for each marsh. Confidence interval contours (95-percent,± 26.0 cm) were delineated above and below the 60-cm inundation contours, and artificial structures, such as roads and bridges, that may present barriers to salt-marsh migration were mapped. This study delineated 114 salt marshes totaling 340 hectares (ha), ranging in size from 0.11 ha (marshes less than 0.2 ha were mapped only if they were on Acadia National Park property) to 52 ha, with a median

Wetland Loss Patterns and Inundation-Productivity ...

Science.gov (United States)

Tidal salt marsh is a key defense against, yet is especially vulnerable to, the effects of accelerated sea level rise. To determine whether salt marshes in southern New England will be stable given increasing inundation over the coming decades, we examined current loss patterns, inundation-productivity feedbacks, and sustaining processes. A multi-decadal analysis of salt marsh aerial extent using historic imagery and maps revealed that salt marsh vegetation loss is both widespread and accelerating, with vegetation loss rates over the past four decades summing to 17.3 %. Landward retreat of the marsh edge, widening and headward expansion of tidal channel networks, loss of marsh islands, and the development and enlargement of interior depressions found on the marsh platform contributed to vegetation loss. Inundation due to sea level rise is strongly suggested as a primary driver: vegetation loss rates were significantly negatively correlated with marsh elevation (r2 = 0.96; p = 0.0038), with marshes situated below mean high water (MHW) experiencing greater declines than marshes sitting well above MHW. Growth experiments with Spartina alterniflora, the Atlantic salt marsh ecosystem dominant, across a range of elevations and inundation regimes further established that greater inundation decreases belowground biomass production of S. alterniflora and, thus, negatively impacts organic matter accumulation. These results suggest that southern New England salt ma

Integrating Physical and Topographic Information Into a Fuzzy Scheme to Map Flooded Area by SAR.

Science.gov (United States)

Pierdicca, Nazzareno; Chini, Marco; Pulvirenti, Luca; Macina, Flavia

2008-07-10

A flood mapping procedure based on a fuzzy sets theory has been developed. The method is based on the integration of Synthetic Aperture Radar (SAR) measurements with additional data on the inundated area, such as a land cover map and a digital elevation model (DEM). The information on land cover has allowed us to account for both specular reflection, typical of open water, and double bounce backscattering, typical of forested and urban areas. DEM has been exploited to include simple hydraulic considerations on the dependence of inundation probability on surface characteristics. Contextual information has been taken into account too. The proposed algorithm has been tested on a flood occurred in Italy on November 1994. A pair of ERS-1 images, collected before and after (three days later) the flood, has been used. The results have been compared with the data provided by a ground survey carried out when the flood reached its maximum extension. Despite the temporal mismatch between the survey and the post-inundation SAR image, the comparison has yielded encouraging results, with the 87% of the pixels correctly classified as inundated.

Flood Inundation Modelling in the Kuantan River Basin using 1D-2D Flood Modeller coupled with ASTER-GDEM

Science.gov (United States)

Ng, Z. F.; Gisen, J. I.; Akbari, A.

2018-03-01

Topography dataset is an important input in performing flood inundation modelling. However, it is always difficult to obtain high resolution topography that provide accurate elevation information. Fortunately, there are some open source topography datasets available with reasonable resolution such as SRTM and ASTER-GDEM. In Malaysia particularly in Kuantan, the modelling research on the floodplain area is still lacking. This research aims to: a) to investigate the suitability of ASTER-GDEM to be applied in the 1D-2D flood inundation modelling for the Kuantan River Basin; b) to generate flood inundation map for Kuantan river basin. The topography dataset used in this study is ASTER-GDEM to generate physical characteristics of watershed in the basin. It is used to perform rainfall runoff modelling for hydrological studies and to delineate flood inundation area in the Flood Modeller. The results obtained have shown that a 30m resolution ASTER-GDEM is applicable as an input for the 1D-2D flood modelling. The simulated water level in 2013 has NSE of 0.644 and RSME of 1.259. As a conclusion, ASTER-GDEM can be used as one alternative topography datasets for flood inundation modelling. However, the flood level obtained from the hydraulic modelling shows low accuracy at flat urban areas.

Development of flood-inundation maps for the Mississippi River in Saint Paul, Minnesota

Science.gov (United States)

Czuba, Christiana R.; Fallon, James D.; Lewis, Corby R.; Cooper, Diane F.

2014-01-01

Digital flood-inundation maps for a 6.3-mile reach of the Mississippi River in Saint Paul, Minnesota, were developed through a multi-agency effort by the U.S. Geological Survey in cooperation with the U.S. Army Corps of Engineers and in collaboration with the National Weather Service. The inundation maps, which can be accessed through the U.S. Geological Survey Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ and the National Weather Service Advanced Hydrologic Prediction Service site at http://water.weather.gov/ahps/inundation.php, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the U.S. Geological Survey streamgage at the Mississippi River at Saint Paul (05331000). The National Weather Service forecasted peak-stage information at the streamgage may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the Mississippi River by means of a one-dimensional step-backwater model. The hydraulic model was calibrated using the most recent stage-discharge relation at the Robert Street location (rating curve number 38.0) of the Mississippi River at Saint Paul (streamgage 05331000), as well as an approximate water-surface elevation-discharge relation at the Mississippi River at South Saint Paul (U.S. Army Corps of Engineers streamgage SSPM5). The model also was verified against observed high-water marks from the recent 2011 flood event and the water-surface profile from existing flood insurance studies. The hydraulic model was then used to determine 25 water-surface profiles for flood stages at 1-foot intervals ranging from approximately bankfull stage to greater than the highest recorded stage at streamgage 05331000. The simulated water-surface profiles were then combined with a geographic information system digital elevation model, derived from high-resolution topography

Flood-inundation maps for the Elkhart River at Goshen, Indiana

Science.gov (United States)

Strauch, Kellan R.

2013-01-01

The U.S. Geological Survey (USGS), in cooperation with the Indiana Office of Community and Rural Affairs, created digital flood-inundation maps for an 8.3-mile reach of the Elkhart River at Goshen, Indiana, extending from downstream of the Goshen Dam to downstream from County Road 17. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to nine selected water levels (stages) at the USGS streamgage at Elkhart River at Goshen (station number 04100500). Current conditions for the USGS streamgages in Indiana may be obtained on the Internet at http://waterdata.usgs.gov/. In addition, stream stage data have been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system (http://water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that are often colocated with USGS streamgages. NWS-forecasted peak-stage information may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated using the most current stage-discharge relation at the Elkhart River at Goshen streamgage. The hydraulic model was then used to compute nine water-surface profiles for flood stages at 1-foot (ft) intervals referenced to the streamgage datum and ranging from approximately bankfull (5 ft) to greater than the highest recorded water level (13 ft). The simulated water-surface profiles were then combined with a geographic information system (GIS) digital-elevation model (DEM), derived from Light Detection and Ranging (LiDAR) data having a 0.37-ft vertical accuracy and 3.9-ft horizontal resolution in order to delineate the area flooded at each

The effect of wave current interactions on the storm surge and inundation in Charleston Harbor during Hurricane Hugo 1989

Science.gov (United States)

Xie, Lian; Liu, Huiqing; Peng, Machuan

The effects of wave-current interactions on the storm surge and inundation induced by Hurricane Hugo in and around the Charleston Harbor and its adjacent coastal regions are examined by using a three-dimensional (3-D) wave-current coupled modeling system. The 3-D storm surge and inundation modeling component of the coupled system is based on the Princeton ocean model (POM), whereas the wave modeling component is based on the third-generation wave model, simulating waves nearshore (SWAN). The results indicate that the effects of wave-induced surface, bottom, and radiation stresses can separately or in combination produce significant changes in storm surge and inundation. The effects of waves vary spatially. In some areas, the contribution of waves to peak storm surge during Hurricane Hugo reached as high as 0.76 m which led to substantial changes in the inundation and drying areas simulated by the storm surge model.

LiDAR and IFSAR-Based Flood Inundation Model Estimates for Flood-Prone Areas of Afghanistan

Science.gov (United States)

Johnson, W. C.; Goldade, M. M.; Kastens, J.; Dobbs, K. E.; Macpherson, G. L.

2014-12-01

Extreme flood events are not unusual in semi-arid to hyper-arid regions of the world, and Afghanistan is no exception. Recent flashfloods and flashflood-induced landslides took nearly 100 lives and destroyed or damaged nearly 2000 homes in 12 villages within Guzargah-e-Nur district of Baghlan province in northeastern Afghanistan. With available satellite imagery, flood-water inundation estimation can be accomplished remotely, thereby providing a means to reduce the impact of such flood events by improving shared situational awareness during major flood events. Satellite orbital considerations, weather, cost, data licensing restrictions, and other issues can often complicate the acquisition of appropriately timed imagery. Given the need for tools to supplement imagery where not available, complement imagery when it is available, and bridge the gap between imagery based flood mapping and traditional hydrodynamic modeling approaches, we have developed a topographic floodplain model (FLDPLN), which has been used to identify and map river valley floodplains with elevation data ranging from 90-m SRTM to 1-m LiDAR. Floodplain "depth to flood" (DTF) databases generated by FLDPLN are completely seamless and modular. FLDPLN has been applied in Afghanistan to flood-prone areas along the northern and southern flanks of the Hindu Kush mountain range to generate a continuum of 1-m increment flood-event models up to 10 m in depth. Elevation data used in this application of FLDPLN included high-resolution, drone-acquired LiDAR (~1 m) and IFSAR (5 m; INTERMAP). Validation of the model has been accomplished using the best available satellite-derived flood inundation maps, such as those issued by Unitar's Operational Satellite Applications Programme (UNOSAT). Results provide a quantitative approach to evaluating the potential risk to urban/village infrastructure as well as to irrigation systems, agricultural fields and archaeological sites.

Inundation mapping – a study based on December 2004 Tsunami Hazard along Chennai coast, Southeast India

Directory of Open Access Journals (Sweden)

C. Satheesh Kumar

2008-07-01

Full Text Available Tsunami impact study has been undertaken along Chennai coast starting from Pulicat to Kovalam. The study area Chennai coast is mainly devoted to prepare large scale action plan maps on tsunami inundation incorporating land use details derived from satellite data along with cadastral data using a GIS tool. Under tsunami inundation mapping along Chennai coast an integrated approach was adopted to prepare thematic maps on land use/land cover and coastal geomorphology using multispectral remote sensing data. The RTK dGPS instruments are used to collect elevation contour data at 0.5 m intervals for the Chennai coast. The GIS tool has been used to incorporate the elevation data, tsunami inundation markings obtained immediately after tsunami and thematic maps derived from remote sensing data. The outcome of this study provides an important clue on variations in tsunami inundation along Chennai coast, which is mainly controlled by local geomorphologic set-up, coastal zone elevation including coastal erosion protection measures and near shore bathymetry. This study highlights the information regarding most vulnerable areas of tsunami and also provides indication to demarcate suitable sites for rehabilitation.

Scenario based tsunami wave height estimation towards hazard evaluation for the Hellenic coastline and examples of extreme inundation zones in South Aegean

Science.gov (United States)

Melis, Nikolaos S.; Barberopoulou, Aggeliki; Frentzos, Elias; Krassanakis, Vassilios

2016-04-01

A scenario based methodology for tsunami hazard assessment is used, by incorporating earthquake sources with the potential to produce extreme tsunamis (measured through their capacity to cause maximum wave height and inundation extent). In the present study we follow a two phase approach. In the first phase, existing earthquake hazard zoning in the greater Aegean region is used to derive representative maximum expected earthquake magnitude events, with realistic seismotectonic source characteristics, and of greatest tsunamigenic potential within each zone. By stacking the scenario produced maximum wave heights a global maximum map is constructed for the entire Hellenic coastline, corresponding to all expected extreme offshore earthquake sources. Further evaluation of the produced coastline categories based on the maximum expected wave heights emphasizes the tsunami hazard in selected coastal zones with important functions (i.e. touristic crowded zones, industrial zones, airports, power plants etc). Owing to its proximity to the Hellenic Arc, many urban centres and being a popular tourist destination, Crete Island and the South Aegean region are given a top priority to define extreme inundation zoning. In the second phase, a set of four large coastal cities (Kalamata, Chania, Heraklion and Rethymno), important for tsunami hazard, due i.e. to the crowded beaches during the summer season or industrial facilities, are explored towards preparedness and resilience for tsunami hazard in Greece. To simulate tsunamis in the Aegean region (generation, propagation and runup) the MOST - ComMIT NOAA code was used. High resolution DEMs for bathymetry and topography were joined via an interface, specifically developed for the inundation maps in this study and with similar products in mind. For the examples explored in the present study, we used 5m resolution for the topography and 30m resolution for the bathymetry, respectively. Although this study can be considered as

Runoff inundation hazard cartography

Science.gov (United States)

Pineux, N.; Degré, A.

2012-04-01

overflowing hazard map), with a rain duration set at 1h. The arable lands are considered as bare, except for the permanent meadows. The worst situation is envisaged, the hydrologic effect of the soil cover in the farming area being variable from a year to another according to the vegetative development and to the cultural operations. The peak discharge is chosen as the more critic parameter because it synthesizes the watershed propensity to stream, its size, and its flow network. The cartographic representation is done in a linear way along the concentrated runoff axes. Whereas this first approach at regional scale includes uncertainties, the aim of this map is currently to prompt consideration of the runoff inundation hazard during the design of urban development projects.

Real-time flood inundation forecasting and mapping for key railway infrastructure: a UK case study

Directory of Open Access Journals (Sweden)

Murphy Alexandra T.

2016-01-01

Full Text Available Flooding events that impede railway infrastructure can cause severe travel delays for the general public and large fines in delayed minutes for the rail industry. Early warnings of flood inundation can give more time to implement mitigation measures which help reduce cancellations, delays and fines. Initial work is reported on the development of a real-time flood inundation forecasting and mapping system for the Cowley Bridge track area near Exeter, UK. This location is on one of the main access routes to South West England and has suffered major floods in the past resulting in significant transport impacts. Flood forecasting systems in the UK mainly forecast river level/flow rather than extent and depth of flood inundation. Here, the development of a chain of coupled models is discussed that link rainfall to river flow, river level and flood extent for the rail track area relating to Cowley Bridge. Historical events are identified to test model performance in predicting inundation of railway infrastructure. The modelling system will operate alongside a series of in-situ sensors chosen to enhance the flood mapping forecasting system. Sensor data will support offline model calibration/verification and real-time data assimilation as well as monitoring flood conditions to inform track closure decisions.

Real-time tsunami inundation forecasting and damage mapping towards enhancing tsunami disaster resiliency

Science.gov (United States)

Koshimura, S.; Hino, R.; Ohta, Y.; Kobayashi, H.; Musa, A.; Murashima, Y.

2014-12-01

With use of modern computing power and advanced sensor networks, a project is underway to establish a new system of real-time tsunami inundation forecasting, damage estimation and mapping to enhance society's resilience in the aftermath of major tsunami disaster. The system consists of fusion of real-time crustal deformation monitoring/fault model estimation by Ohta et al. (2012), high-performance real-time tsunami propagation/inundation modeling with NEC's vector supercomputer SX-ACE, damage/loss estimation models (Koshimura et al., 2013), and geo-informatics. After a major (near field) earthquake is triggered, the first response of the system is to identify the tsunami source model by applying RAPiD Algorithm (Ohta et al., 2012) to observed RTK-GPS time series at GEONET sites in Japan. As performed in the data obtained during the 2011 Tohoku event, we assume less than 10 minutes as the acquisition time of the source model. Given the tsunami source, the system moves on to running tsunami propagation and inundation model which was optimized on the vector supercomputer SX-ACE to acquire the estimation of time series of tsunami at offshore/coastal tide gauges to determine tsunami travel and arrival time, extent of inundation zone, maximum flow depth distribution. The implemented tsunami numerical model is based on the non-linear shallow-water equations discretized by finite difference method. The merged bathymetry and topography grids are prepared with 10 m resolution to better estimate the tsunami inland penetration. Given the maximum flow depth distribution, the system performs GIS analysis to determine the numbers of exposed population and structures using census data, then estimates the numbers of potential death and damaged structures by applying tsunami fragility curve (Koshimura et al., 2013). Since the tsunami source model is determined, the model is supposed to complete the estimation within 10 minutes. The results are disseminated as mapping products to

DFLOWZ: A free program to evaluate the area potentially inundated by a debris flow

Science.gov (United States)

Berti, M.; Simoni, A.

2014-06-01

The transport and deposition mechanisms of debris flows are still poorly understood due to the complexity of the interactions governing the behavior of water-sediment mixtures. Empirical-statistical methods can therefore be used, instead of more sophisticated numerical methods, to predict the depositional behavior of these highly dangerous gravitational movements. We use widely accepted semi-empirical scaling relations and propose an automated procedure (DFLOWZ) to estimate the area potentially inundated by a debris flow event. Beside a digital elevation model (DEM), the procedure has only two input requirements: the debris flow volume and the possible flow-path. The procedure is implemented in Matlab and a Graphical User Interface helps to visualize initial conditions, flow propagation and final results. Different hypothesis about the depositional behavior of an event can be tested together with the possible effect of simple remedial measures. Uncertainties associated to scaling relations can be treated and their impact on results evaluated. Our freeware application aims to facilitate and speed up the process of susceptibility mapping. We discuss limits and advantages of the method in order to inform inexperienced users.

Integrating Physical and Topographic Information Into a Fuzzy Scheme to Map Flooded Area by SAR

Directory of Open Access Journals (Sweden)

Flavia Macina

2008-07-01

Full Text Available A flood mapping procedure based on a fuzzy sets theory has been developed. The method is based on the integration of Synthetic Aperture Radar (SAR measurements with additional data on the inundated area, such as a land cover map and a digital elevation model (DEM. The information on land cover has allowed us to account for both specular reflection, typical of open water, and double bounce backscattering, typical of forested and urban areas. DEM has been exploited to include simple hydraulic considerations on the dependence of inundation probability on surface characteristics. Contextual information has been taken into account too. The proposed algorithm has been tested on a flood occurred in Italy on November 1994. A pair of ERS-1 images, collected before and after (three days later the flood, has been used. The results have been compared with the data provided by a ground survey carried out when the flood reached its maximum extension. Despite the temporal mismatch between the survey and the post-inundation SAR image, the comparison has yielded encouraging results, with the 87% of the pixels correctly classified as inundated.

Development of Real-time Tsunami Inundation Forecast Using Ocean Bottom Tsunami Networks along the Japan Trench

Science.gov (United States)

Aoi, S.; Yamamoto, N.; Suzuki, W.; Hirata, K.; Nakamura, H.; Kunugi, T.; Kubo, T.; Maeda, T.

2015-12-01

In the 2011 Tohoku earthquake, in which huge tsunami claimed a great deal of lives, the initial tsunami forecast based on hypocenter information estimated using seismic data on land were greatly underestimated. From this lesson, NIED is now constructing S-net (Seafloor Observation Network for Earthquakes and Tsunamis along the Japan Trench) which consists of 150 ocean bottom observatories with seismometers and pressure gauges (tsunamimeters) linked by fiber optic cables. To take full advantage of S-net, we develop a new methodology of real-time tsunami inundation forecast using ocean bottom observation data and construct a prototype system that implements the developed forecasting method for the Pacific coast of Chiba prefecture (Sotobo area). We employ a database-based approach because inundation is a strongly non-linear phenomenon and its calculation costs are rather heavy. We prepare tsunami scenario bank in advance, by constructing the possible tsunami sources, and calculating the tsunami waveforms at S-net stations, coastal tsunami heights and tsunami inundation on land. To calculate the inundation for target Sotobo area, we construct the 10-m-mesh precise elevation model with coastal structures. Based on the sensitivities analyses, we construct the tsunami scenario bank that efficiently covers possible tsunami scenarios affecting the Sotobo area. A real-time forecast is carried out by selecting several possible scenarios which can well explain real-time tsunami data observed at S-net from tsunami scenario bank. An advantage of our method is that tsunami inundations are estimated directly from the actual tsunami data without any source information, which may have large estimation errors. In addition to the forecast system, we develop Web services, APIs, and smartphone applications and brush them up through social experiments to provide the real-time tsunami observation and forecast information in easy way to understand toward urging people to evacuate.

Boreal Inundation Mapping with SMAP Radiometer Data for Methane Studies

Science.gov (United States)

Kim, Seungbum; Brisco, Brian; Poncos, Valentin

2017-04-01

Inundation and consequent anoxic condition induce methane release, which is one of the most potent greenhouse gases. Boreal regions contain large amounts of organic carbon, which is a potentially major methane emission source under climatic warming conditions. Boreal wetlands in particular are one of the largest sources of uncertainties in global methane budget. Wetland spatial extent together with the gas release rate remains highly unknown. Characterization of the existing inundation database is poor, because of the inundation under clouds and dense vegetation. In this work, the inundation extent is derived using brightness temperature data acquired by the L-band Soil Moisture Active Passive (SMAP) satellite, which offers the L-band capabilities to penetrate clouds and vegetation at 3-day revisit. The fidelity of the SMAP watermask is assessed as a first step in this investigation by comparing with the following data sets: 3-m resolution maps derived using Radarsat synthetic aperture radar (SAR) data in northern Canada and multi-sensor climatology over Siberia. Because Radarsat coverages are limited despite its high spatial resolution, at the time and location where Radarsats are not available, we also compare with 3-km resolution SMAP SAR data that are concurrent with the SMAP radiometer data globally until July 2015. Inundation extents were derived with Radarsat, SMAP SAR, and SMAP radiometer over the 60 km x 60km area at Peace Athabasca Delta (PAD), Canada on 6 days in spring and summer 2015. The SMAP SAR results match the locations of Radarsat waterbodies. However, the SMAP SAR underestimates the water extent, mainly over mixed pixels that have subpixel land presence. The threshold value (-3 dB) applied to the SMAP SAR was determined previously over the global domain. The threshold is dependent on the type of local landcover within a mixed pixel. Further analysis is needed to locally optimize the threshold. The SMAP radiometer water fraction over Peace

Characterization of Inundated Wetlands with Microwave Remote Sensing: Cross-Product Comparison for Uncertainty Assessment in Tropical Wetlands

Science.gov (United States)

McDonald, K. C.; Jensen, K.; Alvarez, J.; Azarderakhsh, M.; Schroeder, R.; Podest, E.; Chapman, B. D.; Zimmermann, R.

2015-12-01

We have been assembling a global-scale Earth System Data Record (ESDR) of natural Inundated Wetlands to facilitate investigations on their role in climate, biogeochemistry, hydrology, and biodiversity. The ESDR comprises (1) Fine-resolution (100 meter) maps, delineating wetland extent, vegetation type, and seasonal inundation dynamics for regional to continental-scale areas, and (2) global coarse-resolution (~25 km), multi-temporal mappings of inundated area fraction (Fw) across multiple years. During March 2013, the NASA/JPL L-band polarimetric airborne imaging radar, UAVSAR, conducted airborne studies over regions of South America including portions of the western Amazon basin. We collected UAVSAR datasets over regions of the Amazon basin during that time to support systematic analyses of error sources related to the Inundated Wetlands ESDR. UAVSAR datasets were collected over Pacaya Samiria, Peru, Madre de Dios, Peru, and the Napo River in Ecuador. We derive landcover classifications from the UAVSAR datasets emphasizing wetlands regions, identifying regions of open water and inundated vegetation. We compare the UAVSAR-based datasets with those comprising the ESDR to assess uncertainty associated with the high resolution and the coarse resolution ESDR components. Our goal is to create an enhanced ESDR of inundated wetlands with statistically robust uncertainty estimates. The ESDR documentation will include a detailed breakdown of error sources and associated uncertainties within the data record. This work was carried out in part within the framework of the ALOS Kyoto & Carbon Initiative. PALSAR data were provided by JAXA/EORC and the Alaska Satellite Facility. Portions of this work were conducted at the Jet Propulsion Laboratory, California Institute of Technology under contract to the National Aeronautics and Space Administration.

Flood inundation maps for the Wabash and Eel Rivers at Logansport, Indiana

Science.gov (United States)

Fowler, Kathleen K.

2014-01-01

Digital flood-inundation maps for an 8.3-mile reach of the Wabash River and a 7.6-mile reach of the Eel River at Logansport, Indiana (Ind.), were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Office of Community and Rural Affairs. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at USGS streamgage Wabash River at Logansport, Ind. (sta. no. 03329000) and USGS streamgage Eel River near Logansport, Ind. (sta. no. 03328500). Current conditions for estimating near-real-time areas of inundation using USGS streamgage information may be obtained on the Internet at http://waterdata.usgs.gov/. In addition, information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system http:/water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that are often colocated with USGS streamgages. NWS-forecasted peak-stage information may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. For this study, flood profiles were computed for the stream reaches by means of a one-dimensional step-backwater model developed by the U.S. Army Corps of Engineers. The hydraulic model was calibrated by using the most current stage-discharge relations at USGS streamgages 03329000, Wabash River at Logansport, Ind., and 03328500, Eel River near Logansport, Ind. The calibrated hydraulic model was then used to determine five water-surface profiles for flood stage at 1-foot intervals referenced to the Wabash River streamgage datum, and four water-surface profiles for flood stages at 1-foot intervals referenced to the Eel River streamgage datum. The stages range from bankfull to approximately the highest

Potential inundated coastal area estimation in Shanghai with multi-platform SAR and altimetry data

Science.gov (United States)

Ma, Guanyu; Yang, Tianliang; Zhao, Qing; Kubanek, Julia; Pepe, Antonio; Dong, Hongbin; Sun, Zhibin

2017-09-01

As global warming problem is becoming serious in recent decades, the global sea level is continuously rising. This will cause damages to the coastal deltas with the characteristics of low-lying land, dense population, and developed economy. Continuously reclamation costal intertidal and wetland areas are making Shanghai, the mega city of Yangtze River Delta, more vulnerable to sea level rise. In this paper, we investigate the land subsidence temporal evolution of patterns and processes on a stretch of muddy coast located between the Yangtze River Estuary and Hangzou Bay with differential synthetic aperture radar interferometry (DInSAR) analyses. By exploiting a set of 31 SAR images acquired by the ENVISAT/ASAR from February 2007 to May 2010 and a set of 48 SAR images acquired by the COSMO-SkyMed (CSK) sensors from December 2013 to March 2016, coherent point targets as long as land subsidence velocity maps and time series are identified by using the Small Baseline Subset (SBAS) algorithm. With the DInSAR constrained land subsidence model, we predict the land subsidence trend and the expected cumulative subsidence in 2020, 2025 and 2030. Meanwhile, we used altimetrydata and densely distributed in the coastal region are identified (EEMD) algorithm to obtain the average sea level rise rate in the East China Sea. With the land subsidence predictions, sea level rise predictions, and high-precision digital elevation model (DEM), we analyze the combined risk of land subsidence and sea level rise on the coastal areas of Shanghai. The potential inundated areas are mapped under different scenarios.

Impact of hydrogeological factors on groundwater salinization due to ocean-surge inundation

Science.gov (United States)

Yang, Jie; Zhang, Huichen; Yu, Xuan; Graf, Thomas; Michael, Holly A.

2018-01-01

Ocean surges cause seawater inundation of coastal inland areas. Subsequently, seawater infiltrates into coastal aquifers and threatens the fresh groundwater resource. The severity of resulting salinization can be affected by hydrogeological factors including aquifer properties and hydrologic conditions, however, little research has been done to assess these effects. To understand the impacts of hydrogeological factors on groundwater salinization, we numerically simulated an ocean-surge inundation event on a two-dimensional conceptual coastal aquifer using a coupled surface-subsurface approach. We varied model permeability (including anisotropy), inland hydraulic gradient, and recharge rate. Three salinization-assessment indicators were developed, based on flushing time, depth of salt penetration, and a combination of the two, weighted flushing time, with which the impact of hydrogeological factors on groundwater vulnerability to salinization were quantitatively assessed. The vulnerability of coastal aquifers increases with increasing isotropic permeability. Low horizontal permeability (kx) and high vertical permeability (kz) lead to high aquifer vulnerability, and high kx and low kz lead to low aquifer vulnerability. Vulnerability decreases with increasing groundwater hydraulic gradient and increasing recharge rate. Additionally, coastal aquifers with a low recharge rate (R ≤ 300 mm yr-1) may be highly vulnerable to ocean-surge inundation. This study shows how the newly introduced indicators can be used to quantitatively assess coastal aquifer vulnerability. The results are important for global vulnerability assessment of coastal aquifers to ocean-surge inundation.

Coupled 1D-2D hydrodynamic inundation model for sewer overflow: Influence of modeling parameters

Directory of Open Access Journals (Sweden)

Adeniyi Ganiyu Adeogun

2015-10-01

Full Text Available This paper presents outcome of our investigation on the influence of modeling parameters on 1D-2D hydrodynamic inundation model for sewer overflow, developed through coupling of an existing 1D sewer network model (SWMM and 2D inundation model (BREZO. The 1D-2D hydrodynamic model was developed for the purpose of examining flood incidence due to surcharged water on overland surface. The investigation was carried out by performing sensitivity analysis on the developed model. For the sensitivity analysis, modeling parameters, such as mesh resolution Digital Elevation Model (DEM resolution and roughness were considered. The outcome of the study shows the model is sensitive to changes in these parameters. The performance of the model is significantly influenced, by the Manning's friction value, the DEM resolution and the area of the triangular mesh. Also, changes in the aforementioned modeling parameters influence the Flood characteristics, such as the inundation extent, the flow depth and the velocity across the model domain. Keywords: Inundation, DEM, Sensitivity analysis, Model coupling, Flooding

Tsunami run-up and inundation along the coast of Sabah and Sarawak, Malaysia due to a potential Brunei submarine mass failure.

Science.gov (United States)

Tan, Wai Kiat; Teh, Su Yean; Koh, Hock Lye

2017-07-01

Submarine landslides, also known as submarine mass failures (SMFs), are major natural marine disasters that could critically damage coastal facilities such as nuclear power plants and oil and gas platforms. It is therefore essential to investigate submarine landslides for potential tsunami hazard assessment. Three-dimensional seismic data from offshore Brunei have revealed a giant seabed mass deposited by a previous SMF. The submarine mass extends over 120 km from the continental slope of the Baram Canyon at 200 m water depth to the deep basin floor of the Northwest Borneo Trough. A suite of in-house two-dimensional depth-averaged tsunami simulation model TUNA (Tsunami-tracking Utilities and Application) is developed to assess the vulnerability of coastal communities in Sabah and Sarawak subject to potential SMF tsunami. The submarine slide is modeled as a rigid body moving along a planar slope with the center of mass motion parallel to the planar slope and subject to external forces due to added mass, gravity, and dissipation. The nonlinear shallow water equations are utilized to simulate tsunami propagation from deepwater up to the shallow offshore areas. A wetting-drying algorithm is used when a tsunami wave reaches the shoreline to compute run up of tsunami along the shoreline. Run-up wave height and inundation maps are provided for seven densely populated locations in Sabah and Sarawak to highlight potential risks at each location, subject to two scenarios of slide slopes: 2° and 4°. The first wave may arrive at Kudat as early as 0.4 h after the SMF, giving local communities little time to evacuate. Over a small area, maximum inundated depths reaching 20.3 m at Kudat, 26.1 m at Kota Kinabalu, and 15.5 m at Miri are projected, while the maximum inundation distance of 4.86 km is expected at Miri due to its low-lying coast. In view of the vulnerability of some locations to the SMF tsunami, it is important to develop and implement community resilience

Flood-inundation maps for the DuPage River from Plainfield to Shorewood, Illinois, 2013

Science.gov (United States)

Murphy, Elizabeth A.; Sharpe, Jennifer B.

2013-01-01

Digital flood-inundation maps for a 15.5-mi reach of the DuPage River from Plainfield to Shorewood, Illinois, were created by the U.S. Geological Survey (USGS) in cooperation with the Will County Stormwater Management Planning Committee. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ depict estimates of the areal extent of flooding corresponding to selected water levels (gage heights or stages) at the USGS streamgage at DuPage River at Shorewood, Illinois (sta. no. 05540500). Current conditions at the USGS streamgage may be obtained on the Internet at http://waterdata.usgs.gov/usa/nwis/uv?05540500. In addition, the information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system (http://water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that are often colocated with USGS streamgages. The NWS-forecasted peak-stage information, also shown on the DuPage River at Shorewood inundation Web site, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The hydraulic model was then used to determine nine water-surface profiles for flood stages at 1-ft intervals referenced to the streamgage datum and ranging from NWS Action stage of 6 ft to the historic crest of 14.0 ft. The simulated water-surface profiles were then combined with a Digital Elevation Model (DEM) (derived from Light Detection And Ranging (LiDAR) data) by using a Geographic Information System (GIS) in order to delineate the area flooded at each water level. These maps, along with information on the Internet regarding current gage height from USGS streamgages and forecasted stream stages from the NWS, provide emergency

NOAA's Inundation Analysis Tool

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Coastal storms and other meteorological phenomenon can have a significant impact on how high water levels rise and how often. The inundation analysis program is...

Developing an event-tree probabilistic tsunami inundation model for NE Atlantic coasts: Application to case studies

Science.gov (United States)

Omira, Rachid; Baptista, Maria Ana; Matias, Luis

2015-04-01

This study constitutes the first assessment of probabilistic tsunami inundation in the NE Atlantic region, using an event-tree approach. It aims to develop a probabilistic tsunami inundation approach for the NE Atlantic coast with an application to two test sites of ASTARTE project, Tangier-Morocco and Sines-Portugal. Only tsunamis of tectonic origin are considered here, taking into account near-, regional- and far-filed sources. The multidisciplinary approach, proposed here, consists of an event-tree method that gathers seismic hazard assessment, tsunami numerical modelling, and statistical methods. It presents also a treatment of uncertainties related to source location and tidal stage in order to derive the likelihood of tsunami flood occurrence and exceedance of a specific near-shore wave height during a given return period. We derive high-resolution probabilistic maximum wave heights and flood distributions for both test-sites Tangier and Sines considering 100-, 500-, and 1000-year return periods. We find that the probability that a maximum wave height exceeds 1 m somewhere along the Sines coasts reaches about 55% for 100-year return period, and is up to 100% for 1000-year return period. Along Tangier coast, the probability of inundation occurrence (flow depth > 0m) is up to 45% for 100-year return period and reaches 96% in some near-shore costal location for 500-year return period. Acknowledgements: This work is funded by project ASTARTE - Assessment, STrategy And Risk Reduction for Tsunamis in Europe. Grant 603839, 7th FP (ENV.2013.6.4-3 ENV.2013.6.4-3).

Real-time Tsunami Inundation Prediction Using High Performance Computers

Science.gov (United States)

Oishi, Y.; Imamura, F.; Sugawara, D.

2014-12-01

Recently off-shore tsunami observation stations based on cabled ocean bottom pressure gauges are actively being deployed especially in Japan. These cabled systems are designed to provide real-time tsunami data before tsunamis reach coastlines for disaster mitigation purposes. To receive real benefits of these observations, real-time analysis techniques to make an effective use of these data are necessary. A representative study was made by Tsushima et al. (2009) that proposed a method to provide instant tsunami source prediction based on achieving tsunami waveform data. As time passes, the prediction is improved by using updated waveform data. After a tsunami source is predicted, tsunami waveforms are synthesized from pre-computed tsunami Green functions of linear long wave equations. Tsushima et al. (2014) updated the method by combining the tsunami waveform inversion with an instant inversion of coseismic crustal deformation and improved the prediction accuracy and speed in the early stages. For disaster mitigation purposes, real-time predictions of tsunami inundation are also important. In this study, we discuss the possibility of real-time tsunami inundation predictions, which require faster-than-real-time tsunami inundation simulation in addition to instant tsunami source analysis. Although the computational amount is large to solve non-linear shallow water equations for inundation predictions, it has become executable through the recent developments of high performance computing technologies. We conducted parallel computations of tsunami inundation and achieved 6.0 TFLOPS by using 19,000 CPU cores. We employed a leap-frog finite difference method with nested staggered grids of which resolution range from 405 m to 5 m. The resolution ratio of each nested domain was 1/3. Total number of grid points were 13 million, and the time step was 0.1 seconds. Tsunami sources of 2011 Tohoku-oki earthquake were tested. The inundation prediction up to 2 hours after the

Flood-inundation maps for the Wabash River at Terre Haute, Indiana

Science.gov (United States)

Lombard, Pamela J.

2013-01-01

Digital flood-inundation maps for a 6.3-mi reach of the Wabash River from 0.1 mi downstream of the Interstate 70 bridge to 1.1 miles upstream of the Route 63 bridge, Terre Haute, Indiana, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent of flooding corresponding to select water levels (stages) at the USGS streamgage Wabash River at Terre Haute (station number 03341500). Current conditions at the USGS streamgage may be obtained on the Internet from the USGS National Water Information System (http://waterdata.usgs.gov/in/nwis/uv/?site_no=03341500&agency_cd=USGS&p"). In addition, the same data are provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system (http://water.weather.gov/ahps//). Within this system, the NWS forecasts flood hydrographs for the Wabash River at Terre Haute that may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated using the most current stage-discharge relation at the Wabash River at the Terre Haute streamgage. The hydraulic model was then used to compute 22 water-surface profiles for flood stages at 1-ft interval referenced to the streamgage datum and ranging from bank-full to approximately the highest recorded water level at the streamgage. The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from Light Detection and Ranging (LiDAR) data having a 0.37-ft vertical accuracy and a 1.02-ft horizontal accuracy) to delineate the area flooded at each water

A Tank Bromeliad Favors Spider Presence in a Neotropical Inundated Forest.

Directory of Open Access Journals (Sweden)

Yann Hénaut

Full Text Available Tank bromeliads are good models for understanding how climate change may affect biotic associations. We studied the relationships between spiders, the epiphytic tank bromeliad, Aechmea bracteata, and its associated ants in an inundated forest in Quintana Roo, Mexico, during a drought period while, exceptionally, this forest was dry and then during the flooding that followed. We compared spider abundance and diversity between 'Aechmea-areas' and 'control-areas' of the same surface area. We recorded six spider families: the Dipluridae, Ctenidae, Salticidae, Araneidae, Tetragnathidae and Linyphiidae among which the funnel-web tarantula, Ischnothele caudata, the only Dipluridae noted, was the most abundant. During the drought period, the spiders were more numerous in the Aechmea-areas than in the control-areas, but they were not obligatorily associated with the Aechmea. During the subsequent flooding, the spiders were concentrated in the A. bracteata patches, particularly those sheltering an ant colony. Also, a kind of specificity existed between certain spider taxa and ant species, but varied between the drought period and subsequent flooding. We conclude that climatic events modulate the relationship between A. bracteata patches and their associated fauna. Tank bromeliads, previously considered only for their ecological importance in supplying food and water during drought, may also be considered refuges for spiders during flooding. More generally, tank bromeliads have an important role in preserving non-specialized fauna in inundated forests.

A Tank Bromeliad Favors Spider Presence in a Neotropical Inundated Forest.

Science.gov (United States)

Hénaut, Yann; Corbara, Bruno; Pélozuelo, Laurent; Azémar, Frédéric; Céréghino, Régis; Herault, Bruno; Dejean, Alain

2014-01-01

Tank bromeliads are good models for understanding how climate change may affect biotic associations. We studied the relationships between spiders, the epiphytic tank bromeliad, Aechmea bracteata, and its associated ants in an inundated forest in Quintana Roo, Mexico, during a drought period while, exceptionally, this forest was dry and then during the flooding that followed. We compared spider abundance and diversity between 'Aechmea-areas' and 'control-areas' of the same surface area. We recorded six spider families: the Dipluridae, Ctenidae, Salticidae, Araneidae, Tetragnathidae and Linyphiidae among which the funnel-web tarantula, Ischnothele caudata, the only Dipluridae noted, was the most abundant. During the drought period, the spiders were more numerous in the Aechmea-areas than in the control-areas, but they were not obligatorily associated with the Aechmea. During the subsequent flooding, the spiders were concentrated in the A. bracteata patches, particularly those sheltering an ant colony. Also, a kind of specificity existed between certain spider taxa and ant species, but varied between the drought period and subsequent flooding. We conclude that climatic events modulate the relationship between A. bracteata patches and their associated fauna. Tank bromeliads, previously considered only for their ecological importance in supplying food and water during drought, may also be considered refuges for spiders during flooding. More generally, tank bromeliads have an important role in preserving non-specialized fauna in inundated forests.

Flood-inundation maps for the Saddle River in Ho-Ho-Kus Borough, the Village of Ridgewood, and Paramus Borough, New Jersey, 2013

Science.gov (United States)

Watson, Kara M.; Niemoczynski, Michal J.

2014-01-01

Digital flood-inundation maps for a 5.4-mile reach of the Saddle River in New Jersey from Hollywood Avenue in Ho-Ho-Kus Borough downstream through the Village of Ridgewood and Paramus Borough to the confluence with Hohokus Brook in the Village of Ridgewood were created by the U.S. Geological Survey (USGS) in cooperation with the New Jersey Department of Environmental Protection (NJDEP). The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage on the Saddle River at Ridgewood, New Jersey (station 01390500). Current conditions for estimating near real-time areas of inundation using USGS streamgage information may be obtained on the Internet at http://waterdata.usgs.gov/nwis/uv?site_no=01390500 or at the National Weather Services (NWS) Advanced Hydrologic Prediction Service (AHPS) at http://water.weather.gov/ahps2/hydrograph.php?wfo=okx&gage=rwdn4. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated by using the most current stage-discharge relation (March 11, 2011) at the USGS streamgage 01390500, Saddle River at Ridgewood, New Jersey. The hydraulic model was then used to compute 10 water-surface profiles for flood stages at 1-foot (ft) intervals referenced to the streamgage datum, North American Vertical Datum of 1988 (NAVD 88), and ranging from 5 ft, the NWS “action and minor flood stage”, to 14 ft, which is the maximum extent of the stage-discharge rating and 0.6 ft higher than the highest recorded water level at the streamgage. The simulated water-surface profiles were then combined with a geographic information system 3-meter (9.84-ft) digital elevation model derived from Light Detection and Ranging (lidar) data in order to delineate the area flooded

Modelling the ability of source control measures to reduce inundation risk in a community-scale urban drainage system

Science.gov (United States)

Mei, Chao; Liu, Jiahong; Wang, Hao; Shao, Weiwei; Xia, Lin; Xiang, Chenyao; Zhou, Jinjun

2018-06-01

Urban inundation is a serious challenge that increasingly confronts the residents of many cities, as well as policymakers, in the context of rapid urbanization and climate change worldwide. In recent years, source control measures (SCMs) such as green roofs, permeable pavements, rain gardens, and vegetative swales have been implemented to address flood inundation in urban settings, and proven to be cost-effective and sustainable. In order to investigate the ability of SCMs on reducing inundation in a community-scale urban drainage system, a dynamic rainfall-runoff model of a community-scale urban drainage system was developed based on SWMM. SCMs implementing scenarios were modelled under six design rainstorm events with return period ranging from 2 to 100 years, and inundation risks of the drainage system were evaluated before and after the proposed implementation of SCMs, with a risk-evaluation method based on SWMM and analytic hierarchy process (AHP). Results show that, SCMs implementation resulting in significantly reduction of hydrological indexes that related to inundation risks, range of reduction rates of average flow, peak flow, and total flooded volume of the drainage system were 28.1-72.1, 19.0-69.2, and 33.9-56.0 %, respectively, under six rainfall events with return periods ranging from 2 to 100 years. Corresponding, the inundation risks of the drainage system were significantly reduced after SCMs implementation, the risk values falling below 0.2 when the rainfall return period was less than 10 years. Simulation results confirm the effectiveness of SCMs on mitigating inundation, and quantified the potential of SCMs on reducing inundation risks in the urban drainage system, which provided scientific references for implementing SCMs for inundation control of the study area.

Forecasting inundation from debris flows that grow during travel, with application to the Oregon Coast Range, USA

Science.gov (United States)

Reid, Mark E.; Coe, Jeffrey A.; Brien, Dianne

2016-01-01

Many debris flows increase in volume as they travel downstream, enhancing their mobility and hazard. Volumetric growth can result from diverse physical processes, such as channel sediment entrainment, stream bank collapse, adjacent landsliding, hillslope erosion and rilling, and coalescence of multiple debris flows; incorporating these varied phenomena into physics-based debris-flow models is challenging. As an alternative, we embedded effects of debris-flow growth into an empirical/statistical approach to forecast potential inundation areas within digital landscapes in a GIS framework. Our approach used an empirical debris-growth function to account for the effects of growth phenomena. We applied this methodology to a debris-flow-prone area in the Oregon Coast Range, USA, where detailed mapping revealed areas of erosion and deposition along paths of debris flows that occurred during a large storm in 1996. Erosion was predominant in stream channels with slopes > 5°. Using pre- and post-event aerial photography, we derived upslope contributing area and channel-length growth factors. Our method reproduced the observed inundation patterns produced by individual debris flows; it also generated reproducible, objective potential inundation maps for entire drainage networks. These maps better matched observations than those using previous methods that focus on proximal or distal regions of a drainage network.

Automatic domain updating technique for improving computational efficiency of 2-D flood-inundation simulation

Science.gov (United States)

Tanaka, T.; Tachikawa, Y.; Ichikawa, Y.; Yorozu, K.

2017-12-01

Flood is one of the most hazardous disasters and causes serious damage to people and property around the world. To prevent/mitigate flood damage through early warning system and/or river management planning, numerical modelling of flood-inundation processes is essential. In a literature, flood-inundation models have been extensively developed and improved to achieve flood flow simulation with complex topography at high resolution. With increasing demands on flood-inundation modelling, its computational burden is now one of the key issues. Improvements of computational efficiency of full shallow water equations are made from various perspectives such as approximations of the momentum equations, parallelization technique, and coarsening approaches. To support these techniques and more improve the computational efficiency of flood-inundation simulations, this study proposes an Automatic Domain Updating (ADU) method of 2-D flood-inundation simulation. The ADU method traces the wet and dry interface and automatically updates the simulation domain in response to the progress and recession of flood propagation. The updating algorithm is as follow: first, to register the simulation cells potentially flooded at initial stage (such as floodplains nearby river channels), and then if a registered cell is flooded, to register its surrounding cells. The time for this additional process is saved by checking only cells at wet and dry interface. The computation time is reduced by skipping the processing time of non-flooded area. This algorithm is easily applied to any types of 2-D flood inundation models. The proposed ADU method is implemented to 2-D local inertial equations for the Yodo River basin, Japan. Case studies for two flood events show that the simulation is finished within two to 10 times smaller time showing the same result as that without the ADU method.

Assessment of sea water inundation along Daboo creek area in Indus Delta Region, Pakistan

Science.gov (United States)

Zia, Ibrahim; Zafar, Hina; Shahzad, Muhammad I.; Meraj, Mohsin; Kazmi, Jamil H.

2017-12-01

Indus Deltaic Region (IDR) in Pakistan is an erosion vulnerable coast due to the high deep water wave energy. Livelihood of millions of people depends on the fisheries and mangrove forests in IDR. IDR consists of many creeks where Daboo is a major creek located at southeast of the largest city of Pakistan, Karachi. Unfortunately, there has been no detailed study to analyze the damages of sea water intrusion at a large temporal and spatial scale. Therefore, this study is designed to estimate the effects of sea water inundation based on changing sea water surface salinity and sea surface temperature (SST). Sea surface salinity and SST data from two different surveys in Daboo creek during 1986 and 2010 are analyzed to estimate the damages and extent of sea water intrusion. Mean salinity has increased 33.33% whereas mean SST decreased 13.79% from 1987 to 2010. Spatio-temporal analysis of creek area using LANDSAT 5 Thematic mapper (TM) data for the years 1987 and 2010 shows significant amount of erosion at macro scale. Creek area has increased approximately 9.93% (260.86 m2 per year) which is roughly equal to 60 extensive sized shrimp farms. Further Land Use Land Cover (LULC) analyses for years 2001 and 2014 using LANDSAT 7 Enhanced Thematic Mapper Plus (ETM+) has indicated 42.3% decrease in cultivated land. Wet mud flats have spread out at the inner mouth of creek with enormous increase of 123.3%. Significant sea water intrusion has increased the area of barren land by 37.9%. This also resulted in overall decrease of 6.7% in area covered by mangroves. Therefore, this study recorded a significant evidence of sea water intrusion in IDR that has caused serious damages to community living in the area, economical losses. Additionally, it has also changed the environment by reducing creek biological productivity as reported by earlier studies over other regions of the world.

Sensitivity and uncertainty in flood inundation modelling – concept of an analysis framework

Directory of Open Access Journals (Sweden)

T. Weichel

2007-01-01

Full Text Available After the extreme flood event of the Elbe in 2002 the definition of flood risk areas by law and their simulation became more important in Germany. This paper describes a concept of an analysis framework to improve the localisation and duration of validity of flood inundation maps. The two-dimensional finite difference model TrimR2D is used and linked to a Monte-Carlo routine for parameter sampling as well as to selected performance measures. The purpose is the investigation of the impact of different spatial resolutions and the influence of changing land uses in the simulation of flood inundation areas. The technical assembling of the framework is realised and beside the model calibration, first tests with different parameter ranges were done. Preliminary results show good correlations with observed data, but the investigation of shifting land uses reflects only poor changes in the flood extension.

Flood-inundation maps for White River at Petersburg, Indiana

Science.gov (United States)

Fowler, Kathleen K.

2015-08-20

Digital flood-inundation maps for a 7.7-mile reach of the White River at Petersburg, Indiana, were created by the U.S. Geological Survey (USGS), in cooperation with the Indiana Office of Community and Rural Affairs. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at White River at Petersburg, Ind. (03374000). Near-real-time stages at this streamgage may be obtained from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at http:/water.weather.gov/ahps/, which also forecasts flood hydrographs at this site (PTRI3).

A multi-sensor data-driven methodology for all-sky passive microwave inundation retrieval

Science.gov (United States)

Takbiri, Zeinab; Ebtehaj, Ardeshir M.; Foufoula-Georgiou, Efi

2017-06-01

We present a multi-sensor Bayesian passive microwave retrieval algorithm for flood inundation mapping at high spatial and temporal resolutions. The algorithm takes advantage of observations from multiple sensors in optical, short-infrared, and microwave bands, thereby allowing for detection and mapping of the sub-pixel fraction of inundated areas under almost all-sky conditions. The method relies on a nearest-neighbor search and a modern sparsity-promoting inversion method that make use of an a priori dataset in the form of two joint dictionaries. These dictionaries contain almost overlapping observations by the Special Sensor Microwave Imager and Sounder (SSMIS) on board the Defense Meteorological Satellite Program (DMSP) F17 satellite and the Moderate Resolution Imaging Spectroradiometer (MODIS) on board the Aqua and Terra satellites. Evaluation of the retrieval algorithm over the Mekong Delta shows that it is capable of capturing to a good degree the inundation diurnal variability due to localized convective precipitation. At longer timescales, the results demonstrate consistency with the ground-based water level observations, denoting that the method is properly capturing inundation seasonal patterns in response to regional monsoonal rain. The calculated Euclidean distance, rank-correlation, and also copula quantile analysis demonstrate a good agreement between the outputs of the algorithm and the observed water levels at monthly and daily timescales. The current inundation products are at a resolution of 12.5 km and taken twice per day, but a higher resolution (order of 5 km and every 3 h) can be achieved using the same algorithm with the dictionary populated by the Global Precipitation Mission (GPM) Microwave Imager (GMI) products.

A multi-sensor data-driven methodology for all-sky passive microwave inundation retrieval

Directory of Open Access Journals (Sweden)

Z. Takbiri

2017-06-01

Full Text Available We present a multi-sensor Bayesian passive microwave retrieval algorithm for flood inundation mapping at high spatial and temporal resolutions. The algorithm takes advantage of observations from multiple sensors in optical, short-infrared, and microwave bands, thereby allowing for detection and mapping of the sub-pixel fraction of inundated areas under almost all-sky conditions. The method relies on a nearest-neighbor search and a modern sparsity-promoting inversion method that make use of an a priori dataset in the form of two joint dictionaries. These dictionaries contain almost overlapping observations by the Special Sensor Microwave Imager and Sounder (SSMIS on board the Defense Meteorological Satellite Program (DMSP F17 satellite and the Moderate Resolution Imaging Spectroradiometer (MODIS on board the Aqua and Terra satellites. Evaluation of the retrieval algorithm over the Mekong Delta shows that it is capable of capturing to a good degree the inundation diurnal variability due to localized convective precipitation. At longer timescales, the results demonstrate consistency with the ground-based water level observations, denoting that the method is properly capturing inundation seasonal patterns in response to regional monsoonal rain. The calculated Euclidean distance, rank-correlation, and also copula quantile analysis demonstrate a good agreement between the outputs of the algorithm and the observed water levels at monthly and daily timescales. The current inundation products are at a resolution of 12.5 km and taken twice per day, but a higher resolution (order of 5 km and every 3 h can be achieved using the same algorithm with the dictionary populated by the Global Precipitation Mission (GPM Microwave Imager (GMI products.

Hydraulic experiment on evaluation method of tsunami wave pressure using inundation depth and velocity in front of land structure

International Nuclear Information System (INIS)

Arimitsu, Tsuyoshi; Ooe, Kazuya; Kawasaki, Koji

2012-01-01

Hydraulic experiments were conducted to estimate tsunami wave pressure acting on several different types of land structures and examine the influence of a seawall in front of the structure on tsunami wave pressure. Wave pressures were measured at some points on the structure. The existing hydrostatic formula tended to underestimate tsunami wave pressure under the condition of inundation flow with large Froude number. Estimation method of tsunami wave pressure using inundation depth and horizontal velocity at the front of the structure was proposed based on the experimental results. It was confirmed from comparison with the experiments that the vertical distribution of the maximum tsunami wave pressure can be reproduced by employing the proposed method in this study. (author)

Variability of tsunami inundation footprints considering stochastic scenarios based on a single rupture model: Application to the 2011 Tohoku earthquake

KAUST Repository

Goda, Katsuichiro

2015-06-30

The sensitivity and variability of spatial tsunami inundation footprints in coastal cities and towns due to a megathrust subduction earthquake in the Tohoku region of Japan are investigated by considering different fault geometry and slip distributions. Stochastic tsunami scenarios are generated based on the spectral analysis and synthesis method with regards to an inverted source model. To assess spatial inundation processes accurately, tsunami modeling is conducted using bathymetry and elevation data with 50 m grid resolutions. Using the developed methodology for assessing variability of tsunami hazard estimates, stochastic inundation depth maps can be generated for local coastal communities. These maps are important for improving disaster preparedness by understanding the consequences of different situations/conditions, and by communicating uncertainty associated with hazard predictions. The analysis indicates that the sensitivity of inundation areas to the geometrical parameters (i.e., top-edge depth, strike, and dip) depends on the tsunami source characteristics and the site location, and is therefore complex and highly nonlinear. The variability assessment of inundation footprints indicates significant influence of slip distributions. In particular, topographical features of the region, such as ria coast and near-shore plain, have major influence on the tsunami inundation footprints.

Tidal inundation (“Rob”) investigation using time series of high resolution satellite image data and from institu measurements along northern coast of Java (Pantura)

Science.gov (United States)

Andreas, Heri; Usriyah; Zainal Abidin, Hasanuddin; Anggreni Sarsito, Dina

2017-06-01

Tidal inundation (in Javanese they call it “Rob”) is now becoming a well known phenomenon along northern coast of Java Indonesia (Pantura). The occurrence of tidal inundation was recognized at least in the early 2000 and even earlier. In the recent years the tidal inundation comes not only at a high tide but even at the regular tide in some area across Pantura. In fact in location such as Pondok Bali, north of Blanakan, north of Pekalongan, north of Semarang and north west of Demak, seems those areas are sinking to the sea through times. Sea level rise and land subsidence are considered as main factors deriving the occurrence of this tidal inundation. We were using time series of high resolution satellite image data and insitu data measurements to mapping the tidal inundation along northern coast of Java. All available data from google data satellite archives (year 2000- recent years) and any available sources being analyze together with field surveys tagging and also from media information. As a result we can see the tidal inundation are taking place in Tanggerang, Jakarta, Bekasi, Cilamaya, Pondok Bali, Blanakan, Indramayu, Cirebon, Brebes, Tegal, Pemalang, Pekalongan, Kendal, Semarang, Demak, Gresik, Surabaya, Sidoarjo and Pasuruan.

Adapting to sea-level rise in the US Southeast: The influence of built infrastructure and biophysical factors on the inundation of coastal areas

Energy Technology Data Exchange (ETDEWEB)

Daniels, R.C. [Tennessee Univ., Knoxville, TN (United States). Energy, Environment and Resources Center]|[Oak Ridge National Lab., TN (United States); Gornitz, V.M. [National Aeronautics and Space Administration, New York, NY (United States). Goddard Inst. for Space Studies; Mehta, A.J.; Lee, Saychong [Florida Univ., Gainesville, FL (United States). Dept. of Coastal and Oceanographic Engineering; Cushman, R.M. [Oak Ridge National Lab., TN (United States)

1992-11-01

The earth` s global mean surface air temperature has increased by 0.5{degrees}C over the past 100 years. This warming trend has occurred concurrently with increases in the concentration and number of greenhouse gases in the atmosphere. These gases may cause this trend to accelerate in the future and result in a net increase in the earth`s global mean surface air temperature of 1.5 to 4.5{degrees}C by the year 2100. An increase of this magnitude could cause sea surface temperatures to increase would cause sea levels to rise -from thermal expansion of the sea, and the addition of melt waters from alpine glaciers and continental ice sheets. To allow for the cost-effective analysis of the impacts that sea-level rise may have on the US Southeast, a method is needed that will allow sites that are potentially at risk to be identified for study. Previously, no objective method was available to identify such sites. This project addresses this problem by using a geographic data base with information on both physical and climatological factors to identify coastal areas of the US Southeast that are at risk to inundation or accelerated erosion due to sea-level rise. The following six areas were selected for further study from the many identified as being at high risk: Galveston, Texas; Caminada Pass, Louisiana; Bradenton Beach, Florida; Daytona Beach, Florida; McClellanville, South Carolina; and Nags Head, North Carolina. For each study area the amount of land, by land use type, in danger from inundation from three sea-level-rise scenarios was calculated. The calculated values were based on elevation alone.

Adapting to sea-level rise in the US Southeast: The influence of built infrastructure and biophysical factors on the inundation of coastal areas

Energy Technology Data Exchange (ETDEWEB)

Daniels, R. C. [Tennessee Univ., Knoxville, TN (United States). Energy, Environment and Resources Center Oak Ridge National Lab., TN (United States); Gornitz, V. M. [National Aeronautics and Space Administration, New York, NY (United States). Goddard Inst. for Space Studies; Mehta, A. J.; Lee, Saychong [Florida Univ., Gainesville, FL (United States). Dept. of Coastal and Oceanographic Engineering

1992-11-01

The earth' s global mean surface air temperature has increased by 0.5°C over the past 100 years. This warming trend has occurred concurrently with increases in the concentration and number of greenhouse gases in the atmosphere. These gases may cause this trend to accelerate in the future and result in a net increase in the earth's global mean surface air temperature of 1.5 to 4.5°C by the year 2100. An increase of this magnitude could cause sea surface temperatures to increase would cause sea levels to rise -from thermal expansion of the sea, and the addition of melt waters from alpine glaciers and continental ice sheets. To allow for the cost-effective analysis of the impacts that sea-level rise may have on the US Southeast, a method is needed that will allow sites that are potentially at risk to be identified for study. Previously, no objective method was available to identify such sites. This project addresses this problem by using a geographic data base with information on both physical and climatological factors to identify coastal areas of the US Southeast that are at risk to inundation or accelerated erosion due to sea-level rise. The following six areas were selected for further study from the many identified as being at high risk: Galveston, Texas; Caminada Pass, Louisiana; Bradenton Beach, Florida; Daytona Beach, Florida; McClellanville, South Carolina; and Nags Head, North Carolina. For each study area the amount of land, by land use type, in danger from inundation from three sea-level-rise scenarios was calculated. The calculated values were based on elevation alone.

Flood-inundation maps for the Driftwood River and Sugar Creek near Edinburgh, Indiana

Science.gov (United States)

Fowler, Kathleen K.; Kim, Moon H.; Menke, Chad D.

2012-01-01

Digital flood-inundation maps for an 11.2 mile reach of the Driftwood River and a 5.2 mile reach of Sugar Creek, both near Edinburgh, Indiana, were created by the U.S. Geological Survey (USGS) in cooperation with the Camp Atterbury Joint Maneuver Training Center, Edinburgh, Indiana. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent of flooding corresponding to selected water levels (stages) at the USGS streamgage 03363000 Driftwood River near Edinburgh, Ind. Current conditions at the USGS streamgage in Indiana may be obtained on the Internet at http://waterdata.usgs.gov/in/nwis/current/?type=flow. In addition, the information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system at http://water.weather.gov/ahps/. The NWS forecasts flood hydrographs at many places that are often collocated at USGS streamgages. That forecasted peak-stage information, also available on the Internet, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. For this study, flood profiles were computed for the stream reaches by means of a one-dimensional step-backwater model. The model was calibrated using the most current stage-discharge relations at the USGS streamgage 03363000 Driftwood River near Edinburgh, Ind. The hydraulic model was then used to determine elevations throughout the study reaches for nine water-surface profiles for flood stages at 1-ft intervals referenced to the streamgage datum and ranging from bankfull to nearly the highest recorded water level at the USGS streamgage 03363000 Driftwood River near Edinburgh, Ind. The simulated water-surface profiles were then combined with a geospatial digital elevation model (derived from Light Detection and Ranging (LiDAR) data) in order to

Tsunami hazard assessment in the coastal area of Rabat and Salé, Morocco

Directory of Open Access Journals (Sweden)

C. Renou

2011-08-01

Full Text Available In the framework of the three-year SCHEMA European project (www.schemaproject.org, we present a generic methodology developed to produce tsunami building vulnerability and impact maps. We apply this methodology to the Moroccan coast. This study focuses on the Bouregreg Valley which is at the junction between Rabat (administrative capital, and Salé. Both present large populations and new infrastructure development. Using a combination of numerical modelling, field surveys, Earth Observation and GIS data, the risk has been evaluated for this vulnerable area.

Two tsunami scenarios were studied to estimate a realistic range of hazards on this coast: a worst-case scenario based on the historical Lisbon earthquake of 1755 and a moderate scenario based on the Horseshoe earthquake of 28 February 1969. For each scenario, numerical models allowed the production of tsunami hazard maps (maximum inundation extent and maximum inundation depths. Moreover, the modelling results of these two scenarios were compared with the historical data available.

A companion paper to this article (Atillah et al., 2011 presents the following steps of the methodology, namely the elaboration of building damage maps by crossing layers of building vulnerability and the so-inferred inundation depths.

Flood-inundation maps for the Saddle River from Rochelle Park to Lodi, New Jersey, 2012

Science.gov (United States)

Hoppe, Heidi L.; Watson, Kara M.

2012-01-01

Digital flood-inundation maps for a 2.75-mile reach of the Saddle River from 0.2 mile upstream from the Interstate 80 bridge in Rochelle Park to 1.5 miles downstream from the U.S. Route 46 bridge in Lodi, New Jersey, were created by the U.S. Geological Survey (USGS) in cooperation with the New Jersey Department of Environmental Protection (NJDEP). The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at Saddle River at Lodi, New Jersey (station 01391500). Current conditions for estimating near real-time areas of inundation using USGS streamgage information may be obtained on the Internet at http://waterdata.usgs.gov/nwis/uv?site_no=01391500. The National Weather Service (NWS) forecasts flood hydrographs at many places that are often collocated with USGS streamgages. NWS-forecasted peak-stage information may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated using the most current stage-discharge relations at the Saddle River at Lodi, New Jersey streamgage and documented high-water marks from recent floods. The hydraulic model was then used to determine 11 water-surface profiles for flood stages at the Saddle River streamgage at 1-ft intervals referenced to the streamgage datum, North American Vertical Datum of 1988 (NAVD 88), and ranging from bankfull, 0.5 ft below NWS Action Stage, to the extent of the stage-discharge rating, which is approximately 1 ft higher than the highest recorded water level at the streamgage. Action Stage is the stage which when reached by a rising stream the NWS or a partner needs to take some type of mitigation action in

Flood-inundation maps for the East Fork White River at Columbus, Indiana

Science.gov (United States)

Lombard, Pamela J.

2013-01-01

Digital flood-inundation maps for a 5.4-mile reach of the East Fork White River at Columbus, Indiana, from where the Flatrock and Driftwood Rivers combine to make up East Fork White River to just upstream of the confluence of Clifty Creek with the East Fork White River, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation, depict estimates of the areal extent of flooding corresponding to selected water levels (stages) at USGS streamgage 03364000, East Fork White River at Columbus, Indiana. Current conditions at the USGS streamgage may be obtained on the Internet from the USGS National Water Information System (http://waterdata.usgs.gov/in/nwis/uv/?site_no=03364000&agency_cd=USGS&). The National Weather Service (NWS) forecasts flood hydrographs for the East Fork White River at Columbus, Indiana at their Advanced Hydrologic Prediction Service (AHPS) flood warning system Website (http://water.weather.gov/ahps/), that may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The hydraulic model was calibrated by using the most current stage-discharge relation at USGS streamgage 03364000, East Fork White River at Columbus, Indiana. The calibrated hydraulic model was then used to determine 15 water-surface profiles for flood stages at 1-foot (ft) intervals referenced to the streamgage datum and ranging from bankfull to approximately the highest recorded water level at the streamgage. The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from Light Detection and Ranging (LiDAR) data), having a 0.37-ft vertical accuracy and a 1.02 ft

Analyzing the inundation pattern of the Poyang Lake floodplain by passive microwave data

NARCIS (Netherlands)

Shang, H.; Li, J.; Menenti, M.

2015-01-01

The soil wetness condition is a useful indicator of inundation hazard in floodplains, such as the Poyang Lake floodplain. Special Sensor Microwave Imager (SSM/I) passive microwave data were used to monitor water-saturated soil and open water areas of the Poyang Lake floodplain from 2001 to 2008,

Flood-inundation maps for the White River near Edwardsport, Indiana

Science.gov (United States)

Fowler, Kathleen K.

2014-01-01

Digital flood-inundation maps for a 3.3-mile reach of the White River near Edwardsport, (Ind.), were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at USGS streamgage 03360730, White River near Edwardsport, Ind. Near-real-time stages at this streamgage may be obtained from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service Advanced Hydrologic Prediction Service at http://water.weather.gov/ahps/, which also forecasts flood hydrographs at this site (site EDWI3.)

What is missing? An operational inundation mapping framework by SAR data

Science.gov (United States)

Shen, X.; Anagnostou, E. N.; Zeng, Z.; Kettner, A.; Hong, Y.

2017-12-01

Compared to optical sensors, synthetic aperture radar (SAR) works all-day all-weather. In addition, its spatial resolution does not decrease with the height of the platform and is thus applicable to a range of important studies. However, existing studies did not address the operational demands of real-time inundation mapping. The direct proof is that no water body product exists for any SAR-based satellites. Then what is missing between science and products? Automation and quality. What makes it so difficult to develop an operational inundation mapping technique based on SAR data? Spectrum-wise, unlike optical water indices such as MNDWI, AWEI etc., where a relative constant threshold may apply across acquisition of images, regions and sensors, the threshold to separate water from non-water pixels in each SAR images has to be individually chosen. The optimization of the threshold is the first obstacle to the automation of the SAR data algorithm. Morphologically, the quality and reliability of the results have been compromised by over-detection caused by smooth surface and shadowing area, the noise-like speckle and under-detection caused by strong-scatter disturbance. In this study, we propose a three-step framework that addresses all aforementioned issues of operational inundation mapping by SAR data. The framework consists of 1) optimization of Wishart distribution parameters of single/dual/fully-polarized SAR data, 2) morphological removal of over-detection, and 3) machine-learning based removal of under-detection. The framework utilizes not only the SAR data, but also the synergy of digital elevation model (DEM), and optical sensor-based products of fine resolution, including the water probability map, land cover classification map (optional), and river width. The framework has been validated throughout multiple areas in different parts of the world using different satellite SAR data and globally available ancillary data products. Therefore, it has the potential

Flood-inundation maps for Big Creek from the McGinnis Ferry Road bridge to the confluence of Hog Wallow Creek, Alpharetta and Roswell, Georgia

Science.gov (United States)

Musser, Jonathan W.

2015-08-20

Digital flood-inundation maps for a 12.4-mile reach of Big Creek that extends from 260 feet above the McGinnis Ferry Road bridge to the U.S. Geological Survey (USGS) streamgage at Big Creek below Hog Wallow Creek at Roswell, Georgia (02335757), were developed by the USGS in cooperation with the cities of Alpharetta and Roswell, Georgia. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at Big Creek near Alpharetta, Georgia (02335700). Real-time stage information from this USGS streamgage may be obtained at http://waterdata.usgs.gov/ and can be used in conjunction with these maps to estimate near real-time areas of inundation. The National Weather Service (NWS) is incorporating results from this study into the Advanced Hydrologic Prediction Service (AHPS) flood-warning system http://water.weather.gov/ahps/). The NWS forecasts flood hydrographs for many streams where the USGS operates streamgages and provides flow data. The forecasted peak-stage information for the USGS streamgage at Big Creek near Alpharetta (02335700), available through the AHPS Web site, may be used in conjunction with the maps developed for this study to show predicted areas of flood inundation.

Flood-inundation maps for South Fork Peachtree Creek from the Brockett Road bridge to the Willivee Drive bridge, DeKalb County, Georgia

Science.gov (United States)

Musser, Jonathan W.

2015-10-14

Digital flood-inundation maps for a 5.3-mile reach of South Fork Peachtree Creek that extends from about 500 feet above the Brockett Road bridge to the Willivee Drive bridge were developed by the U.S. Geological Survey (USGS) in cooperation with DeKalb County, Georgia. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at South Fork Peachtree at Casa Drive, near Clarkston, Georgia (02336152). Real-time stage information from this USGS streamgage may be obtained at http://waterdata.usgs.gov/ and can be used in conjunction with these maps to estimate near real-time areas of inundation. The National Weather Service (NWS) is incorporating results from this study into the Advanced Hydrologic Prediction Service (AHPS) flood-warning system (http://water.weather.gov/ahps/).

Estimating floodwater depths from flood inundation maps and topography

Science.gov (United States)

Cohen, Sagy; Brakenridge, G. Robert; Kettner, Albert; Bates, Bradford; Nelson, Jonathan M.; McDonald, Richard R.; Huang, Yu-Fen; Munasinghe, Dinuke; Zhang, Jiaqi

2018-01-01

Information on flood inundation extent is important for understanding societal exposure, water storage volumes, flood wave attenuation, future flood hazard, and other variables. A number of organizations now provide flood inundation maps based on satellite remote sensing. These data products can efficiently and accurately provide the areal extent of a flood event, but do not provide floodwater depth, an important attribute for first responders and damage assessment. Here we present a new methodology and a GIS-based tool, the Floodwater Depth Estimation Tool (FwDET), for estimating floodwater depth based solely on an inundation map and a digital elevation model (DEM). We compare the FwDET results against water depth maps derived from hydraulic simulation of two flood events, a large-scale event for which we use medium resolution input layer (10 m) and a small-scale event for which we use a high-resolution (LiDAR; 1 m) input. Further testing is performed for two inundation maps with a number of challenging features that include a narrow valley, a large reservoir, and an urban setting. The results show FwDET can accurately calculate floodwater depth for diverse flooding scenarios but also leads to considerable bias in locations where the inundation extent does not align well with the DEM. In these locations, manual adjustment or higher spatial resolution input is required.

Application of STORMTOOLS's simplified flood inundation model with sea level rise to assess impacts to RI coastal areas

Science.gov (United States)

Spaulding, M. L.

2015-12-01

The vision for STORMTOOLS is to provide access to a suite of coastal planning tools (numerical models et al), available as a web service, that allows wide spread accessibly and applicability at high resolution for user selected coastal areas of interest. The first product developed under this framework were flood inundation maps, with and without sea level rise, for varying return periods for RI coastal waters. The flood mapping methodology is based on using the water level vs return periods at a primary NOAA water level gauging station and then spatially scaling the values, based on the predictions of high resolution, storm and wave simulations performed by Army Corp of Engineers, North Atlantic Comprehensive Coastal Study (NACCS) for tropical and extratropical storms on an unstructured grid, to estimate inundation levels for varying return periods. The scaling for the RI application used Newport, RI water levels as the reference point. Predictions are provided for once in 25, 50, and 100 yr return periods (at the upper 95% confidence level), with sea level rises of 1, 2, 3, and 5 ft. Simulations have also been performed for historical hurricane events including 1938, Carol (1954), Bob (1991), and Sandy (2012) and nuisance flooding events with return periods of 1, 3, 5, and 10 yr. Access to the flooding maps is via a web based, map viewer that seamlessly covers all coastal waters of the state at one meter resolution. The GIS structure of the map viewer allows overlays of additional relevant data sets (roads and highways, wastewater treatment facilities, schools, hospitals, emergency evacuation routes, etc.) as desired by the user. The simplified flooding maps are publically available and are now being implemented for state and community resilience planning and vulnerability assessment activities in response to climate change impacts.

Hurricanes Harvey and Irma - High-Resolution Flood Mapping and Monitoring from Sentinel SAR with the Depolarization Reduction Algorithm for Global Observations of InundatioN (DRAGON)

Science.gov (United States)

Nghiem, S. V.; Brakenridge, G. R.; Nguyen, D. T.

2017-12-01

Hurricane Harvey inflicted historical catastrophic flooding across extensive regions around Houston and southeast Texas after making landfall on 25 August 2017. The Federal Emergency Management Agency (FEMA) requested urgent supports for flood mapping and monitoring in an emergency response to the extreme flood situation. An innovative satellite remote sensing method, called the Depolarization Reduction Algorithm for Global Observations of inundatioN (DRAGON), has been developed and implemented for use with Sentinel synthetic aperture radar (SAR) satellite data at a resolution of 10 meters to identify, map, and monitor inundation including pre-existing water bodies and newly flooded areas. Results from this new method are hydrologically consistent and have been verified with known surface waters (e.g., coastal ocean, rivers, lakes, reservoirs, etc.), with clear-sky high-resolution WorldView images (where waves can be seen on surface water in inundated areas within a small spatial coverage), and with other flood maps from the consortium of Global Flood Partnership derived from multiple satellite datasets (including clear-sky Landsat and MODIS at lower resolutions). Figure 1 is a high-resolution (4K UHD) image of a composite inundation map for the region around Rosharon (in Brazoria County, south of Houston, Texas). This composite inundation map reveals extensive flooding on 29 August 2017 (four days after Hurricane Harvey made landfall), and the inundation was still persistent in most of the west and south of Rosharon one week later (5 September 2017) while flooding was reduced in the east of Rosharon. Hurricane Irma brought flooding to a number of areas in Florida. As of 10 September 2017, Sentinel SAR flood maps reveal inundation in the Florida Panhandle and over lowland surfaces on several islands in the Florida Keys. However, Sentinel SAR results indicate that flooding along the Florida coast was not extreme despite Irma was a Category-5 hurricane that might

A Tank Bromeliad Favors Spider Presence in a Neotropical Inundated Forest

Science.gov (United States)

Hénaut, Yann; Corbara, Bruno; Pélozuelo, Laurent; Azémar, Frédéric; Céréghino, Régis; Herault, Bruno; Dejean, Alain

2014-01-01

Tank bromeliads are good models for understanding how climate change may affect biotic associations. We studied the relationships between spiders, the epiphytic tank bromeliad, Aechmea bracteata, and its associated ants in an inundated forest in Quintana Roo, Mexico, during a drought period while, exceptionally, this forest was dry and then during the flooding that followed. We compared spider abundance and diversity between ‘Aechmea-areas’ and ‘control-areas’ of the same surface area. We recorded six spider families: the Dipluridae, Ctenidae, Salticidae, Araneidae, Tetragnathidae and Linyphiidae among which the funnel-web tarantula, Ischnothele caudata, the only Dipluridae noted, was the most abundant. During the drought period, the spiders were more numerous in the Aechmea-areas than in the control-areas, but they were not obligatorily associated with the Aechmea. During the subsequent flooding, the spiders were concentrated in the A. bracteata patches, particularly those sheltering an ant colony. Also, a kind of specificity existed between certain spider taxa and ant species, but varied between the drought period and subsequent flooding. We conclude that climatic events modulate the relationship between A. bracteata patches and their associated fauna. Tank bromeliads, previously considered only for their ecological importance in supplying food and water during drought, may also be considered refuges for spiders during flooding. More generally, tank bromeliads have an important role in preserving non-specialized fauna in inundated forests. PMID:25494055

A well-balanced meshless tsunami propagation and inundation model

Science.gov (United States)

Brecht, Rüdiger; Bihlo, Alexander; MacLachlan, Scott; Behrens, Jörn

2018-05-01

We present a novel meshless tsunami propagation and inundation model. We discretize the nonlinear shallow-water equations using a well-balanced scheme relying on radial basis function based finite differences. For the inundation model, radial basis functions are used to extrapolate the dry region from nearby wet points. Numerical results against standard one- and two-dimensional benchmarks are presented.

Flood-inundation maps for an 8.9-mile reach of the South Fork Little River at Hopkinsville, Kentucky

Science.gov (United States)

Lant, Jeremiah G.

2013-01-01

Digital flood-inundation maps for an 8.9-mile reach of South Fork Little River at Hopkinsville, Kentucky, were created by the U.S. Geological Survey (USGS) in cooperation with the City of Hopkinsville Community Development Services. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at South Fork Little River at Highway 68 By-Pass at Hopkinsville, Kentucky (station no. 03437495). Current conditions for the USGS streamgage may be obtained online at the USGS National Water Information System site (http://waterdata.usgs.gov/nwis/inventory?agency_code=USGS&site_no=03437495). In addition, the information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service flood warning system (http://water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that are often co-located at USGS streamgages. The forecasted peak-stage information, also available on the Internet, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the South Fork Little River reach by using HEC-RAS, a one-dimensional step-backwater model developed by the U.S. Army Corps of Engineers. The hydraulic model was calibrated by using the most current (2012) stage-discharge relation at the South Fork Little River at Highway 68 By-Pass at Hopkinsville, Kentucky, streamgage and measurements collected during recent flood events. The calibrated model was then used to calculate 13 water-surface profiles for a sequence of flood stages, most at 1-foot intervals, referenced to the streamgage datum and ranging from a stage near bank full to the estimated elevation of the 1.0-percent annual exceedance

Numerical Computation of Underground Inundation in Multiple Layers Using the Adaptive Transfer Method

Directory of Open Access Journals (Sweden)

Hyung-Jun Kim

2018-01-01

Full Text Available Extreme rainfall causes surface runoff to flow towards lowlands and subterranean facilities, such as subway stations and buildings with underground spaces in densely packed urban areas. These facilities and areas are therefore vulnerable to catastrophic submergence. However, flood modeling of underground space has not yet been adequately studied because there are difficulties in reproducing the associated multiple horizontal layers connected with staircases or elevators. This study proposes a convenient approach to simulate underground inundation when two layers are connected. The main facet of this approach is to compute the flow flux passing through staircases in an upper layer and to transfer the equivalent quantity to a lower layer. This is defined as the ‘adaptive transfer method’. This method overcomes the limitations of 2D modeling by introducing layers connecting concepts to prevent large variations in mesh sizes caused by complicated underlying obstacles or local details. Consequently, this study aims to contribute to the numerical analysis of flow in inundated underground spaces with multiple floors.

Evacuation planning for plausible worst case inundation scenarios in Honolulu, Hawaii.

Science.gov (United States)

Kim, Karl; Pant, Pradip; Yamashita, Eric

2015-01-01

Honolulu is susceptible to coastal flooding hazards. Like other coastal cities, Honolulu&s long-term economic viability and sustainability depends on how well it can adapt to changes in the natural and built environment. While there is a disagreement over the magnitude and extent of localized impacts associated with climate change, it is widely accepted that by 2100 there will be at least a meter in sea level rise (SLR) and an increase in extreme weather events. Increased exposure and vulnerabilities associated with urbanization and location of human activities in coastal areas warrants serious consideration by planners and policy makers. This article has three objectives. First, flooding due to the combined effects of SLR and episodic hydro-meteorological and geophysical events in Honolulu are investigated and the risks to the community are quantified. Second, the risks and vulnerabilities of critical infrastructure and the surface transportation system are described. Third, using the travel demand software, travel distances and travel times for evacuation from inundated areas are modeled. Data from three inundation models were used. The first model simulated storm surge from a category 4 hurricane similar to Hurricane Iniki which devastated the island of Kauai in 1992. The second model estimates inundation based on five tsunamis that struck Hawaii. A 1-m increase in sea level was included in both the hurricane storm surge and tsunami flooding models. The third model used in this article generated a 500-year flood event due to riverine flooding. Using a uniform grid cell structure, the three inundation maps were used to assess the worst case flooding scenario. Based on the flood depths, the ruling hazard (hurricane, tsunami, or riverine flooding) for each grid cell was determined. The hazard layer was analyzed with socioeconomic data layers to determine the impact on vulnerable populations, economic activity, and critical infrastructure. The analysis focused both

Inundation risk for embanked rivers

Directory of Open Access Journals (Sweden)

W. G. Strupczewski

2013-08-01

Full Text Available The Flood Frequency Analysis (FFA concentrates on probability distribution of peak flows of flood hydrographs. However, examination of floods that haunted and devastated the large parts of Poland lead us to revision of the views on the assessment of flood risk of Polish rivers. It turned out that flooding is caused not only by the overflow of the levee crest but also due to the prolonged exposure to high water on levees structure causing dangerous leaks and breaches that threaten their total destruction. This is because the levees are weakened by long-lasting water pressure and as a matter of fact their damage usually occurs after the culmination has passed the affected location. The probability of inundation is the total of probabilities of exceeding embankment crest by flood peak and the probability of washout of levees. Therefore, in addition to the maximum flow one should also consider the duration of high waters in a river channel. In the paper the new two-component model of flood dynamics: "Duration of high waters–Discharge Threshold–Probability of non-exceedance" (DqF, with the methodology of its parameter estimation was proposed as a completion to the classical FFA methods. Such a model can estimate the duration of stages (flows of an assumed magnitude with a given probability of exceedance. The model combined with the technical evaluation of the probability of levee breaches due to the duration (d of flow above alarm stage gives the annual probability of inundation caused by the embankment breaking. The results of theoretical investigation were illustrated by a practical example of the model implementation to the series of daily flow of the Vistula River at Szczucin. Regardless of promising results, the method of risk assessment due to prolonged exposure of levees to high water is still in its infancy despite its great cognitive potential and practical importance. Therefore, we would like to point out the need for and usefulness of

Influence of changes in wetland inundation extent on net fluxes of carbon dioxide and methane in northern high latitudes from 1993 to 2004

International Nuclear Information System (INIS)

Zhuang, Qianlai; Zhu, Xudong; He, Yujie; Prigent, Catherine; Melillo, Jerry M; Kicklighter, David W; David McGuire, A; Prinn, Ronald G

2015-01-01

Estimates of the seasonal and interannual exchanges of carbon dioxide (CO 2 ) and methane (CH 4 ) between land ecosystems north of 45°N and the atmosphere are poorly constrained, in part, because of uncertainty in the temporal variability of water-inundated land area. Here we apply a process-based biogeochemistry model to evaluate how interannual changes in wetland inundation extent might have influenced the overall carbon dynamics of the region during the time period 1993–2004. We find that consideration by our model of these interannual variations between 1993 and 2004, on average, results in regional estimates of net methane sources of 67.8 ± 6.2 Tg CH 4 yr −1 , which is intermediate to model estimates that use two static inundation extent datasets (51.3 ± 2.6 and 73.0 ± 3.6 Tg CH 4 yr −1 ). In contrast, consideration of interannual changes of wetland inundation extent result in regional estimates of the net CO 2 sink of −1.28 ± 0.03 Pg C yr −1 with a persistent wetland carbon sink from −0.38 to −0.41 Pg C yr −1 and a upland sink from −0.82 to −0.98 Pg C yr −1 . Taken together, despite the large methane emissions from wetlands, the region is a consistent greenhouse gas sink per global warming potential (GWP) calculations irrespective of the type of wetland datasets being used. However, the use of satellite-detected wetland inundation extent estimates a smaller regional GWP sink than that estimated using static wetland datasets. Our sensitivity analysis indicates that if wetland inundation extent increases or decreases by 10% in each wetland grid cell, the regional source of methane increases 13% or decreases 12%, respectively. In contrast, the regional CO 2 sink responds with only 7–9% changes to the changes in wetland inundation extent. Seasonally, the inundated area changes result in higher summer CH 4 emissions, but lower summer CO 2 sinks, leading to lower summer negative greenhouse gas forcing. Our analysis further

Flood-inundation maps for a 6.5-mile reach of the Kentucky River at Frankfort, Kentucky

Science.gov (United States)

Lant, Jeremiah G.

2013-01-01

Digital flood-inundation maps for a 6.5-mile reach of Kentucky River at Frankfort, Kentucky, were created by the U.S. Geological Survey (USGS) in cooperation with the City of Frankfort Office of Emergency Management. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage Kentucky River at Lock 4 at Frankfort, Kentucky (station no. 03287500). Current conditions for the USGS streamgage may be obtained online at the USGS National Water Information System site (http://waterdata.usgs.gov/nwis/inventory?agency_code=USGS&site_no=03287500). In addition, the information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system (http:/water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that are often colocated at USGS streamgages. The forecasted peak-stage information, also available on the Internet, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the Kentucky River reach by using HEC–RAS, a one-dimensional step-backwater model developed by the U.S. Army Corps of Engineers. The hydraulic model was calibrated by using the most current (2013) stage-discharge relation for the Kentucky River at Lock 4 at Frankfort, Kentucky, in combination with streamgage and high-water-mark measurements collected for a flood event in May 2010. The calibrated model was then used to calculate 26 water-surface profiles for a sequence of flood stages, at 1-foot intervals, referenced to the streamgage datum and ranging from a stage near bankfull to the elevation that breached the levees protecting the City of Frankfort. To delineate the flooded area at

Comparison of physical and semi-empirical hydraulic models for flood inundation mapping

Science.gov (United States)

Tavakoly, A. A.; Afshari, S.; Omranian, E.; Feng, D.; Rajib, A.; Snow, A.; Cohen, S.; Merwade, V.; Fekete, B. M.; Sharif, H. O.; Beighley, E.

2016-12-01

Various hydraulic/GIS-based tools can be used for illustrating spatial extent of flooding for first-responders, policy makers and the general public. The objective of this study is to compare four flood inundation modeling tools: HEC-RAS-2D, Gridded Surface Subsurface Hydrologic Analysis (GSSHA), AutoRoute and Height Above the Nearest Drainage (HAND). There is a trade-off among accuracy, workability and computational demand in detailed, physics-based flood inundation models (e.g. HEC-RAS-2D and GSSHA) in contrast with semi-empirical, topography-based, computationally less expensive approaches (e.g. AutoRoute and HAND). The motivation for this study is to evaluate this trade-off and offer guidance to potential large-scale application in an operational prediction system. The models were assessed and contrasted via comparability analysis (e.g. overlapping statistics) by using three case studies in the states of Alabama, Texas, and West Virginia. The sensitivity and accuracy of physical and semi-eimpirical models in producing inundation extent were evaluated for the following attributes: geophysical characteristics (e.g. high topographic variability vs. flat natural terrain, urbanized vs. rural zones, effect of surface roughness paratermer value), influence of hydraulic structures such as dams and levees compared to unobstructed flow condition, accuracy in large vs. small study domain, effect of spatial resolution in topographic data (e.g. 10m National Elevation Dataset vs. 0.3m LiDAR). Preliminary results suggest that semi-empericial models tend to underestimate in a flat, urbanized area with controlled/managed river channel around 40% of the inundation extent compared to the physical models, regardless of topographic resolution. However, in places where there are topographic undulations, semi-empericial models attain relatively higher level of accuracy than they do in flat non-urbanized terrain.

Simulating storm surge inundation and damage potential within complex port facilities

Science.gov (United States)

Mawdsley, Robert; French, Jon; Fujiyama, Taku; Achutan, Kamalasudhan

2017-04-01

Storm surge inundation of port facilities can cause damage to critical elements of infrastructure, significantly disrupt port operations and cause downstream impacts on vital supply chains. A tidal surge in December 2013 in the North Sea partly flooded the Port of Immingham, which handles the largest volume of bulk cargo in the UK including major flows of coal and biomass for power generation. This flooding caused damage to port and rail transport infrastructure and disrupted operations for several weeks. This research aims to improve resilience to storm surges using hydrodynamic modelling coupled to an agent-based model of port operations. Using the December 2013 event to validate flood extent, depth and duration, we ran a high resolution hydrodynamic simulation using the open source Telemac 2D finite element code. The underlying Digital Elevation Model (DEM) was derived from Environment Agency LiDAR data, with ground truthing of the flood defences along the port frontage. Major infrastructure and buildings are explicitly resolved with varying degrees of permeability. Telemac2D simulations are run in parallel and take only minutes on a single 16 cpu compute node. Inundation characteristics predicted using Telemac 2D differ from a simple Geographical Information System 'bath-tub' analysis of the DEM based upon horizontal application of the maximum water level across the port topography. The hydrodynamic simulation predicts less extensive flooding and more closely matches observed flood extent. It also provides more precise depth and duration curves. Detailed spatial flood depth and duration maps were generated for a range of tide and surge scenarios coupled to mean sea-level rise projections. These inundation scenarios can then be integrated with critical asset databases and an agent-based model of port operation (MARS) that is capable of simulating storm surge disruption along wider supply chains. Port operators are able to act on information from a particular

EXPERIMENTAL STUDIES ON DIFFICULTY OF EVACUATION FROM UNDERGROUND SPACES UNDER INUNDATED SITUATIONS USING REAL SCALE MODELS

Science.gov (United States)

Baba, Yasuyuki; Ishigaki, Taisuke; Toda, Keiichi; Nakagawa, Hajime

Many urbanized cities in Japan are located in alluvial plains, and the vulnerability of urbanized areas to flood disaster is highlighted by flood attacks due to heavy rain fall or typhoons. Underground spaces located in the urbanized area are flood-prone areas, and the intrusion of flood watar into underground space inflicted severe damages on urban functions and infrastructures. In a similar way, low-lying areas like "bowl-shaped" depression and underpasses under highway and railroad bridges are also prone to floods. The underpasses are common sites of accidents of submerged vehicles, and severe damage including human damage occasionally occurs under flooding conditions. To reduce the damage due to inundation in underground space, needless to say, early evacuation is one of the most important countermeasures. This paper shows some experimental results of evacuation tests from underground spaces under inundated situations. The difficulities of the evacuation from underground space has been investigated by using real scale models (door, staircase and vehicle), and the limit for safety evacuation is discussed. From the results, it is found that water depth of 0.3 - 0.4m would be a critical situation for the evacuation from underground space through staircases and door and that 0.7 - 0.8m deep on the ground would be also a critical situation for safety evacuation though the doors of the vehicle. These criteria have some possibility to vary according to different inundated situations, and they are also influenced by the individual variation like the difference of physical strength. This means that these criteria requires cautious stance to use although they show a sort of an index of the limitation for saftty evacuation from underground space.

Vulnerability of National Park Service beaches to inundation during a direct hurricane landfall: Fire Island National Seashore

Science.gov (United States)

Stockdon, Hilary F.; Thompson, David M.

2007-01-01

Waves and storm surge associated with strong tropical storms are part of the natural process of barrier-island evolution and can cause extensive morphologic changes in coastal parks, leading to reduced visitor accessibility and enjoyment. Even at Fire Island National Seashore, a barrier-island coastal park in New York where extratropical storms (northeasters) dominate storm activity, the beaches are vulnerable to the powerful, sand-moving forces of hurricanes. The vulnerability of park beaches to inundation, and associated extreme coastal change, during a direct hurricane landfall can be assessed by comparing the elevations of storm-induced mean-water levels (storm surge) to the elevations of the crest of the sand dune that defines the beach system. Maps detailing the inundation potential for Category 1-4 hurricanes can be used by park managers to determine the relative vulnerability of various barrier-island parks and to assess which areas of a particular park are more susceptible to inundation and extreme coastal changes.

Flood-inundation maps for a nine-mile reach of the Des Plaines River from Riverwoods to Mettawa, Illinois

Science.gov (United States)

Murphy, Elizabeth A.; Soong, David T.; Sharpe, Jennifer B.

2012-01-01

Digital flood-inundation maps for a 9-mile reach of the Des Plaines River from Riverwoods to Mettawa, Illinois, were created by the U.S. Geological Survey (USGS) in cooperation with the Lake County Stormwater Management Commission and the Villages of Lincolnshire and Riverwoods. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent of flooding corresponding to selected water levels (gage heights) at the USGS streamgage at Des Plaines River at Lincolnshire, Illinois (station no. 05528100). Current conditions at the USGS streamgage may be obtained on the Internet at http://waterdata.usgs.gov/usa/nwis/uv?05528100. In addition, this streamgage is incorporated into the Advanced Hydrologic Prediction Service (AHPS) flood warning system (http://water.weather.gov/ahps/) by the National Weather Service (NWS). The NWS forecasts flood hydrographs at many places that are often co-located at USGS streamgages. The NWS forecasted peak-stage information, also shown on the Des Plaines River at Lincolnshire inundation Web site, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The hydraulic model was then used to determine seven water-surface profiles for flood stages at roughly 1-ft intervals referenced to the streamgage datum and ranging from the 50- to 0.2-percent annual exceedance probability flows. The simulated water-surface profiles were then combined with a Geographic Information System (GIS) Digital Elevation Model (DEM) (derived from Light Detection And Ranging (LiDAR) data) in order to delineate the area flooded at each water level. These maps, along with information on the Internet regarding current gage height from USGS streamgages and forecasted stream stages from

The Limit of Inundation of the September 29, 2009, Tsunami on Tutuila, American Samoa

Science.gov (United States)

Jaffe, Bruce E.; Gelfenbaum, Guy; Buckley, Mark L.; Watt, Steve; Apotsos, Alex; Stevens, Andrew W.; Richmond, Bruce M.

2010-01-01

U.S. Geological Survey scientists investigated the coastal impacts of the September 29, 2009, South Pacific tsunami in Tutuila, American Samoa in October and November 2009, including mapping the alongshore variation in the limit of inundation. Knowing the inundation limit is useful for planning safer coastal development and evacuation routes for future tsunamis and for improving models of tsunami hazards. This report presents field data documenting the limit of inundation at 18 sites around Tutuila collected in the weeks following the tsunami using Differential GPS (DGPS). In total, 15,703 points along inundation lines were mapped. Estimates of DGPS error and uncertainty in interpretation of the inundation line are provided as electronic files that accompany this report.

A Parallel, Multi-Scale Watershed-Hydrologic-Inundation Model with Adaptively Switching Mesh for Capturing Flooding and Lake Dynamics

Science.gov (United States)

Ji, X.; Shen, C.

2017-12-01

Flood inundation presents substantial societal hazards and also changes biogeochemistry for systems like the Amazon. It is often expensive to simulate high-resolution flood inundation and propagation in a long-term watershed-scale model. Due to the Courant-Friedrichs-Lewy (CFL) restriction, high resolution and large local flow velocity both demand prohibitively small time steps even for parallel codes. Here we develop a parallel surface-subsurface process-based model enhanced by multi-resolution meshes that are adaptively switched on or off. The high-resolution overland flow meshes are enabled only when the flood wave invades to floodplains. This model applies semi-implicit, semi-Lagrangian (SISL) scheme in solving dynamic wave equations, and with the assistant of the multi-mesh method, it also adaptively chooses the dynamic wave equation only in the area of deep inundation. Therefore, the model achieves a balance between accuracy and computational cost.

Increased cesium uptake by water tupelo under inundated conditions

International Nuclear Information System (INIS)

McLeod, K.W.

1980-01-01

Low level releases of 137 Cs to streams has resulted in concentrations greater than background levels in soils, sediments and plants of the Savannah River swamp. The object of this study was to determine the effect of inundation on the absorption of 137 Cs by water tupelo (Nyssa aquatica) which is dominant in the swamp and is able to survive and grow well under flooded conditions. Results show that actively growing young water tupelo absorb about twice as much 137 Cs when grown in the laboratory under inundated conditions suggesting that in the spring, when inundated conditions usually exist and rapid growth occurs, uptake of 137 Cs is high. Some Cs is transported from soil depths and returned to soil surface via incorporation into leaves and subsequent leaf fall, thus continually mixing Cs which was buried below the soil surface. (U.K.)

Flood-inundation maps for the White River at Noblesville, Indiana

Science.gov (United States)

Martin, Zachary W.

2017-11-02

Digital flood-inundation maps for a 7.5-mile reach of the White River at Noblesville, Indiana, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science website at https://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the White River at Noblesville, Ind., streamgage (USGS station number 03349000). Real-time stages at this streamgage may be obtained from the USGS National Water Information System at https://waterdata.usgs.gov/nwis or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at http:/water.weather.gov/ahps/, which also forecasts flood hydrographs at the same site as the USGS streamgage (NWS site NBLI3).Flood profiles were computed for the stream reach by means of a one-dimensional, step-backwater hydraulic modeling software developed by the U.S. Army Corps of Engineers. The hydraulic model was calibrated using the current (2016) stage-discharge rating at the USGS streamgage 03349000, White River at Noblesville, Ind., and documented high-water marks from the floods of September 4, 2003, and May 6, 2017. The hydraulic model was then used to compute 15 water-surface profiles for flood stages at 1-foot (ft) intervals referenced to the streamgage datum ranging from 10.0 ft (the NWS “action stage”) to 24.0 ft, which is the highest stage interval of the current (2016) USGS stage-discharge rating curve and 2 ft higher than the NWS “major flood stage.” The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from light detection and ranging data having a 0.98-ft vertical accuracy and 4.9-ft horizontal resolution) to delineate the area flooded at each stage.The availability of these maps, along with internet

Inundation downscaling for the development of a long-term and global inundation database compatible to SWOT mission

Science.gov (United States)

Aires, Filipe; Prigent, Catherine; Papa, Fabrice

2014-05-01

The Global Inundation Extent from Multi-Satellite (GIEMS) provides multi-year monthly variations of the global surface water extent at about 25 kmx25 km resolution, from 1993 to 2007. It is derived from multiple satellite observations. Its spatial resolution is usually compatible with climate model outputs and with global land surface model grids but is clearly not adequate for local applications that require the characterization of small individual water bodies. There is today a strong demand for high-resolution inundation extent datasets, for a large variety of applications such as water management, regional hydrological modeling, or for the analysis of mosquitos-related diseases. Even for climate applications, the GIEMS resolution might be limited given recent results on the key importance of the smallest ponds in the emission of CH4, as compared to the largest ones. If the inundation extent is combined to altimetry measurements to obtain water volume changes, and finally river discharge to the ocean (Frappart et al. 2011), then a better resolved inundation extent will also improve the accuracy of these estimates. In the context of the SWOT mission, the downscaling of GIEMS has multiple applications uses but a major one will be to use the SWOT retrievals to develop a downscaling of GIEMS. This SWOT-compatible downscaling could then be used to built a SWOT-compatible high-resolution database back in time from 1993 to the SWOT launch date. This extension of SWOT record is necessary to perform climate studies related to climate change. This paper present three approaches to do downscale GIEMS. Two basins will be considered for illustrative purpose, Amazon, Niger and Mekhong. - Aires, F., F. Papa, C. Prigent, J.-F. Cretaux and M. Berge-Nguyen, Characterization and downscaling of the inundation extent over the Inner Niger delta using a multi-wavelength retrievals and Modis data, J. of Hydrometeorology, in press, 2014. - Aires, F., F. Papa and C. Prigent, A long

Mapping flood hazards under uncertainty through probabilistic flood inundation maps

Science.gov (United States)

Stephens, T.; Bledsoe, B. P.; Miller, A. J.; Lee, G.

2017-12-01

Changing precipitation, rapid urbanization, and population growth interact to create unprecedented challenges for flood mitigation and management. Standard methods for estimating risk from flood inundation maps generally involve simulations of floodplain hydraulics for an established regulatory discharge of specified frequency. Hydraulic model results are then geospatially mapped and depicted as a discrete boundary of flood extents and a binary representation of the probability of inundation (in or out) that is assumed constant over a project's lifetime. Consequently, existing methods utilized to define flood hazards and assess risk management are hindered by deterministic approaches that assume stationarity in a nonstationary world, failing to account for spatio-temporal variability of climate and land use as they translate to hydraulic models. This presentation outlines novel techniques for portraying flood hazards and the results of multiple flood inundation maps spanning hydroclimatic regions. Flood inundation maps generated through modeling of floodplain hydraulics are probabilistic reflecting uncertainty quantified through Monte-Carlo analyses of model inputs and parameters under current and future scenarios. The likelihood of inundation and range of variability in flood extents resulting from Monte-Carlo simulations are then compared with deterministic evaluations of flood hazards from current regulatory flood hazard maps. By facilitating alternative approaches of portraying flood hazards, the novel techniques described in this presentation can contribute to a shifting paradigm in flood management that acknowledges the inherent uncertainty in model estimates and the nonstationary behavior of land use and climate.

Flood-Inundation Maps for Sugar Creek at Crawfordsville, Indiana

Science.gov (United States)

Martin, Zachary W.

2016-06-06

Digital flood-inundation maps for a 6.5-mile reach of Sugar Creek at Crawfordsville, Indiana, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Office of Community and Rural Affairs. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage 03339500, Sugar Creek at Crawfordsville, Ind. Near-real-time stages at this streamgage may be obtained on the Internet from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at http://water.weather.gov/ahps/, which also forecasts flood hydrographs at this site (NWS site CRWI3).Flood profiles were computed for the USGS streamgage 03339500, Sugar Creek at Crawfordsville, Ind., reach by means of a one-dimensional step-backwater hydraulic modeling software developed by the U.S. Army Corps of Engineers. The hydraulic model was calibrated using the current stage-discharge rating at the USGS streamgage 03339500, Sugar Creek at Crawfordsville, Ind., and high-water marks from the flood of April 19, 2013, which reached a stage of 15.3 feet. The hydraulic model was then used to compute 13 water-surface profiles for flood stages at 1-foot (ft) intervals referenced to the streamgage datum ranging from 4.0 ft (the NWS “action stage”) to 16.0 ft, which is the highest stage interval of the current USGS stage-discharge rating curve and 2 ft higher than the NWS “major flood stage.” The simulated water-surface profiles were then combined with a Geographic Information System digital elevation model (derived from light detection and ranging [lidar]) data having a 0.49-ft root mean squared error and 4.9-ft horizontal resolution) to delineate the area flooded at each stage.The availability

Flood-inundation maps for the West Branch Susquehanna River near the Boroughs of Lewisburg and Milton, Pennsylvania

Science.gov (United States)

Roland, Mark A.; Hoffman, Scott A.

2014-01-01

Digital flood-inundation maps for an approximate 8-mile reach of the West Branch Susquehanna River from approximately 2 miles downstream from the Borough of Lewisburg, extending upstream to approximately 1 mile upstream from the Borough of Milton, Pennsylvania, were created by the U.S. Geological Survey (USGS) in cooperation with the Susquehanna River Basin Commission (SRBC). The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict the estimated areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage 01553500, West Branch Susquehanna River at Lewisburg, Pa. In addition, the information has been provided to the Susquehanna River Basin Commission (SRBC) for incorporation into their Susquehanna Inundation Map Viewer (SIMV) flood warning system (http://maps.srbc.net/simv/). The National Weather Service (NWS) forecasted peak-stage information (http://water.weather.gov/ahps) for USGS streamgage 01553500, West Branch Susquehanna River at Lewisburg, Pa., may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. Calibration of the model was achieved using the most current stage-discharge relations (rating number 11.1) at USGS streamgage 01553500, West Branch Susquehanna River at Lewisburg, Pa., a documented water-surface profile from the December 2, 2010, flood, and recorded peak stage data. The hydraulic model was then used to determine 26 water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datum ranging from 14 feet (ft) to 39 ft. Modeled flood stages, as defined by NWS, include Action Stage, 14 ft; Flood Stage, 18 ft; Moderate Flood Stage, 23 ft; and Major Flood Stage, 28 ft. Geographic information system (GIS) technology

Flood Inundation Mapping in the Logone Floodplain from Multi Temporal Landsat ETM+Imagery

Science.gov (United States)

Jung, Hahn Chul; Alsdorf, Douglas E.; Moritz, Mark; Lee, Hyongki; Vassolo, Sara

2011-01-01

Yearly flooding in the Logone floodplain makes an impact on agricultural, pastoral, and fishery systems in the Lake Chad Basin. Since the flooding extent and depth are highly variable, flood inundation mapping helps us make better use of water resources and prevent flood hazards in the Logone floodplain. The flood maps are generated from 33 multi temporal Landsat Enhanced Thematic Mapper Plus (ETM+) during three years 2006 to 2008. Flooded area is classified using a short-wave infrared band whereas open water is classified by Iterative Self-organizing Data Analysis (ISODATA) clustering. The maximum flooding extent in the study area increases up to approximately 5.8K km2 in late October 2008. The study also provides strong correlation of the flooding extents with water height variations in both the floodplain and the river based on a second polynomial regression model. The water heights are from ENIVSAT altimetry in the floodplain and gauge measurements in the river. Coefficients of determination between flooding extents and water height variations are greater than 0.91 with 4 to 36 days in phase lag. Floodwater drains back to the river and to the northeast during the recession period in December and January. The study supports understanding of the Logone floodplain dynamics in detail of spatial pattern and size of the flooding extent and assists the flood monitoring and prediction systems in the catchment.

Flood-inundation maps for the White River at Indianapolis, Indiana, 2014

Science.gov (United States)

Nystrom, Elizabeth A.

2015-01-01

Digital flood-inundation maps for a 6.4-mile reach of the White River in Indianapolis, Indiana, from 0.3 miles upstream of Michigan Street to the Harding Street Generating Station dam (at the confluence with Lick Creek), were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Office of Community and Rural Affairs. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage on the White River at Indianapolis, Ind. (station number 03353000). Near-real-time stages at this streamgage may be obtained on the Internet from the USGS National Water Information System at http://waterdata.usgs.gov/or the National Weather Service (NWS) Advanced Hydrologic Prediction Service athttp://water.weather.gov/ahps/, which also forecasts flood hydrographs at this site.

High Resolution Hurricane Storm Surge and Inundation Modeling (Invited)

Science.gov (United States)

Luettich, R.; Westerink, J. J.

2010-12-01

Coastal counties are home to nearly 60% of the U.S. population and industry that accounts for over 16 million jobs and 10% of the U.S. annual gross domestic product. However, these areas are susceptible to some of the most destructive forces in nature, including tsunamis, floods, and severe storm-related hazards. Since 1900, tropical cyclones making landfall on the US Gulf of Mexico Coast have caused more than 9,000 deaths; nearly 2,000 deaths have occurred during the past half century. Tropical cyclone-related adjusted, annualized losses in the US have risen from 1.3 billion from 1949-1989, to 10.1 billion from 1990-1995, and $35.8 billion per year for the period 2001-2005. The risk associated with living and doing business in the coastal areas that are most susceptible to tropical cyclones is exacerbated by rising sea level and changes in the characteristics of severe storms associated with global climate change. In the five years since hurricane Katrina devastated the northern Gulf of Mexico Coast, considerable progress has been made in the development and utilization of high resolution coupled storm surge and wave models. Recent progress will be presented with the ADCIRC + SWAN storm surge and wave models. These tightly coupled models use a common unstructured grid in the horizontal that is capable of covering large areas while also providing high resolution (i.e., base resolution down to 20m plus smaller subgrid scale features such as sea walls and levees) in areas that are subject to surge and inundation. Hydrodynamic friction and overland winds are adjusted to account for local land cover. The models scale extremely well on modern high performance computers allowing rapid turnaround on large numbers of compute cores. The models have been adopted for FEMA National Flood Insurance Program studies, hurricane protection system design and risk analysis, and quasi-operational forecast systems for several regions of the country. They are also being evaluated as

Quantifying Uncertainty in Flood Inundation Mapping Using Streamflow Ensembles and Multiple Hydraulic Modeling Techniques

Science.gov (United States)

Hosseiny, S. M. H.; Zarzar, C.; Gomez, M.; Siddique, R.; Smith, V.; Mejia, A.; Demir, I.

2016-12-01

The National Water Model (NWM) provides a platform for operationalize nationwide flood inundation forecasting and mapping. The ability to model flood inundation on a national scale will provide invaluable information to decision makers and local emergency officials. Often, forecast products use deterministic model output to provide a visual representation of a single inundation scenario, which is subject to uncertainty from various sources. While this provides a straightforward representation of the potential inundation, the inherent uncertainty associated with the model output should be considered to optimize this tool for decision making support. The goal of this study is to produce ensembles of future flood inundation conditions (i.e. extent, depth, and velocity) to spatially quantify and visually assess uncertainties associated with the predicted flood inundation maps. The setting for this study is located in a highly urbanized watershed along the Darby Creek in Pennsylvania. A forecasting framework coupling the NWM with multiple hydraulic models was developed to produce a suite ensembles of future flood inundation predictions. Time lagged ensembles from the NWM short range forecasts were used to account for uncertainty associated with the hydrologic forecasts. The forecasts from the NWM were input to iRIC and HEC-RAS two-dimensional software packages, from which water extent, depth, and flow velocity were output. Quantifying the agreement between output ensembles for each forecast grid provided the uncertainty metrics for predicted flood water inundation extent, depth, and flow velocity. For visualization, a series of flood maps that display flood extent, water depth, and flow velocity along with the underlying uncertainty associated with each of the forecasted variables were produced. The results from this study demonstrate the potential to incorporate and visualize model uncertainties in flood inundation maps in order to identify the high flood risk zones.

GIS inundation mapping and dam breach analysis of Woolwich Dam using HEC-geoRAS

Energy Technology Data Exchange (ETDEWEB)

Mocan, N. [Crozier and Associates Inc., Collingwood, ON (Canada); Joy, D.M. [Guelph Univ., ON (Canada); Rungis, G. [Grand River Conservation Authority, Cambridge, ON (Canada)

2006-07-01

A study was conducted to determine the extent of flood inundation given a hypothetical dam breach scenario of the Woolwich Dam located in the Grand River Watershed, 2.5 km north of the Town of Elmira, Ontario. The dam is operated by the Grand River Conservation Authority and was constructed to provide low-flow augmentation to Canagagigue Creek. Advances in the computational capabilities of numerical models along with the availability of fine resolution geospatial data has lead to significant advances in the evaluation of catastrophic consequences due to the ensuing flood waters when dams fail. The hydraulic models HEC-RAS and HEC-GeoRAS were used in this study along with GIS to produce high resolution spatial and temporal flood inundation mapping. Given the proximity to the Town of Elmira, the dam is classified as having a high hazard potential. The large size and high hazard potential of the dam suggests that the Inflow Design Flood (IDF) is the Probable Maximum Flood (PMF) event. The outlet structure of the spillway consists of 4 ogee-type concrete spillways equipped with radial gates. A low-level concrete pipe located within the spillway structure provides spillage for maintenance purposes. The full flow capacity of the spillway structure is 297 cubic metres per second at the full supply level of 364.8 metres. In addition to GIS flood inundation maps, this paper included the results of flood hydrographs, water surface profiles and peak flow data. It was concluded that techniques used in this analysis should be considered for use in the development of emergency management planning and dam safety assessments across Canada. 6 refs., 3 tabs., 4 figs.

Flood-inundation maps for the Patoka River in and near Jasper, southwestern Indiana

Science.gov (United States)

Fowler, Kathleen K.

2018-01-23

Digital flood-inundation maps for a 9.5-mile reach of the Patoka River in and near the city of Jasper, southwestern Indiana (Ind.), from the streamgage near County Road North 175 East, downstream to State Road 162, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science web site at https://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage Patoka River at Jasper, Ind. (station number 03375500). The Patoka streamgage is located at the upstream end of the 9.5-mile river reach. Near-real-time stages at this streamgage may be obtained from the USGS National Water Information System at https://waterdata.usgs.gov/ or the National Weather Service Advanced Hydrologic Prediction Service at http://water.weather.gov/ahps/, although flood forecasts and stages for action and minor, moderate, and major flood stages are not currently (2017) available at this site (JPRI3).Flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The hydraulic model was calibrated by using the most current stage-discharge relation at the Patoka River at Jasper, Ind., streamgage and the documented high-water marks from the flood of April 30, 2017. The calibrated hydraulic model was then used to compute five water-surface profiles for flood stages referenced to the streamgage datum ranging from 15 feet (ft), or near bankfull, to 19 ft. The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from light detection and ranging [lidar] data having a 0.98 ft vertical accuracy and 4.9 ft horizontal resolution) to delineate the area flooded at each water level.The availability of these flood-inundation maps, along with real

Estimated probabilities, volumes, and inundation areas depths of potential postwildfire debris flows from Carbonate, Slate, Raspberry, and Milton Creeks, near Marble, Gunnison County, Colorado

Science.gov (United States)

Stevens, Michael R.; Flynn, Jennifer L.; Stephens, Verlin C.; Verdin, Kristine L.

2011-01-01

the 25-year-recurrence, 1-hour-duration rainfall. The largest postwildfire debris-flow volumes were estimated for Carbonate Creek and Milton Creek drainage basins, for both the 5- and 25-year-recurrence, 1-hour-duration rainfalls. Results from FLO-2D modeling of the 5-year and 25-year recurrence, 1-hour rainfalls indicate that the debris flows from the four drainage basins would reach or nearly reach the Crystal River. The model estimates maximum instantaneous depths of debris-flow material during postwildfire debris flows that exceeded 5 meters in some areas, but the differences in model results between the 5-year and 25-year recurrence, 1-hour rainfalls are small. Existing stream channels or topographic flow paths likely control the distribution of debris-flow material, and the difference in estimated debris-flow volume (about 25 percent more volume for the 25-year-recurrence, 1-hour-duration rainfall compared to the 5-year-recurrence, 1-hour-duration rainfall) does not seem to substantially affect the estimated spatial distribution of debris-flow material. Historically, the Marble area has experienced periodic debris flows in the absence of wildfire. This report estimates the probability and volume of debris flow and maximum instantaneous inundation area depths after hypothetical wildfire and rainfall. This postwildfire debris-flow report does not address the current (2010) prewildfire debris-flow hazards that exist near Marble.

Typhoon Doksuri Flooding in 2017 - High-Resolution Inundation Mapping and Monitoring from Sentinel Satellite SAR Data

Science.gov (United States)

Nghiem, S. V.; Nguyen, D. T.

2017-12-01

In 2017, typhoons and hurricanes have inflicted catastrophic flooding across extensive regions in many countries on several continents, including Asia and North America. The U.S. Federal Emergency Management Agency (FEMA) requested urgent support for flood mapping and monitoring in an emergency response to the devastating flood situation. An innovative satellite remote sensing method, called the Depolarization Reduction Algorithm for Global Observations of inundatioN (DRAGON), has been developed and implemented for use with Sentinel synthetic aperture radar (SAR) satellite data at a resolution of 10 meters to identify, map, and monitor inundation including pre-existing water bodies and newly flooded areas. Because Sentinel SAR operates at C-band microwave frequency, it can be used for flood mapping regardless of could cover conditions typically associated with storms, and thus can provide immediate results without the need to wait for the clouds to clear out. In Southeast Asia, Typhoon Doksuri caused significant flooding across extensive regions in Vietnam and other countries in September 2017. Figure 1 presents the flood mapping result over a region around Hà Tĩnh (north central coast of Vietnam) showing flood inundated areas (in yellow) on 16 September 2017 together with pre-existing surface water (in blue) on 4 September 2017. This is just one example selected from a larger flood map covering an extensive region of about 250 km x 680 km all along the central coast of Vietnam.

Responses to river inundation pressures control prey selection of riparian beetles.

Directory of Open Access Journals (Sweden)

Matt J O'Callaghan

Full Text Available Riparian habitats are subjected to frequent inundation (flooding and are characterised by food webs that exhibit variability in aquatic/terrestrial subsidies across the ecotone. The strength of this subsidy in active riparian floodplains is thought to underpin local biodiversity. Terrestrial invertebrates dominate the fauna, exhibiting traits that allow exploitation of variable aquatic subsidies while reducing inundation pressures, leading to inter-species micro-spatial positioning. The effect these strategies have on prey selection is not known. This study hypothesised that plasticity in prey choice from either aquatic or terrestrial sources is an important trait linked to inundation tolerance and avoidance.We used hydrological, isotopic and habitat analyses to investigate the diet of riparian Coleoptera in relation to inundation risk and relative spatial positioning in the floodplain. The study examined patch scale and longitudinal changes in utilisation of the aquatic subsidy according to species traits. Prey sourced from terrestrial or emerging/stranded aquatic invertebrates varied in relation to traits for inundation avoidance or tolerance strategies. Traits that favoured rapid dispersal corresponded with highest proportions of aquatic prey, with behavioural traits further predicting uptake. Less able dispersers showed minimal use of aquatic subsidy and switched to a terrestrial diet under moderate inundation pressures. All trait groups showed a seasonal shift in diet towards terrestrial prey in the early spring. Prey selection became exaggerated towards aquatic prey in downstream samples.Our results suggest that partitioning of resources and habitat creates overlapping niches that increase the processing of external subsidies in riparian habitats. By demonstrating functional complexity, this work advances understanding of floodplain ecosystem processes and highlights the importance of hydrological variability. With an increasing interest

Integrating Radarsat-2, Lidar, and Worldview-3 Imagery to maximize detection of forested inundation extent in the Delmarva Peninsula, USA

Science.gov (United States)

Vanderhoof, Melanie; Distler, Hayley; Mendiola, Di Ana; Lang, Megan

2017-01-01

Natural variability in surface-water extent and associated characteristics presents a challenge to gathering timely, accurate information, particularly in environments that are dominated by small and/or forested wetlands. This study mapped inundation extent across the Upper Choptank River Watershed on the Delmarva Peninsula, occurring within both Maryland and Delaware. We integrated six quad-polarized Radarsat-2 images, Worldview-3 imagery, and an enhanced topographic wetness index in a random forest model. Output maps were filtered using light detection and ranging (lidar)-derived depressions to maximize the accuracy of forested inundation extent. Overall accuracy within the integrated and filtered model was 94.3%, with 5.5% and 6.0% errors of omission and commission for inundation, respectively. Accuracy of inundation maps obtained using Radarsat-2 alone were likely detrimentally affected by less than ideal angles of incidence and recent precipitation, but were likely improved by targeting the period between snowmelt and leaf-out for imagery collection. Across the six Radarsat-2 dates, filtering inundation outputs by lidar-derived depressions slightly elevated errors of omission for water (+1.0%), but decreased errors of commission (−7.8%), resulting in an average increase of 5.4% in overall accuracy. Depressions were derived from lidar datasets collected under both dry and average wetness conditions. Although antecedent wetness conditions influenced the abundance and total area mapped as depression, the two versions of the depression datasets showed a similar ability to reduce error in the inundation maps. Accurate mapping of surface water is critical to predicting and monitoring the effect of human-induced change and interannual variability on water quantity and quality.

Leveraging North Carolina's QL2 Lidar to Quantify Sensitivity of National Water Model Derived Flood Inundation Extent to DEM Resolution

Science.gov (United States)

Lovette, J. P.; Lenhardt, W. C.; Blanton, B.; Duncan, J. M.; Stillwell, L.

2017-12-01

The National Water Model (NWM) has provided a novel framework for near real time flood inundation mapping across CONUS at a 10m resolution. In many regions, this spatial scale is quickly being surpassed through the collection of high resolution lidar (1 - 3m). As one of the leading states in data collection for flood inundation mapping, North Carolina is currently improving their previously available 20 ft statewide elevation product to a Quality Level 2 (QL2) product with a nominal point spacing of 0.7 meters. This QL2 elevation product increases the ground points by roughly ten times over the previous statewide lidar product, and by over 250 times when compared to the 10m NED elevation grid. When combining these new lidar data with the discharge estimates from the NWM, we can further improve statewide flood inundation maps and predictions of at-risk areas. In the context of flood risk management, these improved predictions with higher resolution elevation models consistently represent an improvement on coarser products. Additionally, the QL2 lidar also includes coarse land cover classification data for each point return, opening the possibility for expanding analysis beyond the use of only digital elevation models (e.g. improving estimates of surface roughness, identifying anthropogenic features in floodplains, characterizing riparian zones, etc.). Using the NWM Height Above Nearest Drainage approach, we compare flood inundation extents derived from multiple lidar-derived grid resolutions to assess the tradeoff between precision and computational load in North Carolina's coastal river basins. The elevation data distributed through the state's new lidar collection program provide spatial resolutions ranging from 5-50 feet, with most inland areas also including a 3 ft product. Data storage increases by almost two orders of magnitude across this range, as does processing load. In order to further assess the validity of the higher resolution elevation products on

Modelling tsunami inundation for risk analysis at the Andaman Sea Coast of Thailand

Science.gov (United States)

Kaiser, G.; Kortenhaus, A.

2009-04-01

The mega-tsunami of Dec. 26, 2004 strongly impacted the Andaman Sea coast of Thailand and devastated coastal ecosystems as well as towns, settlements and tourism resorts. In addition to the tragic loss of many lives, the destruction or damage of life-supporting infrastructure, such as buildings, roads, water & power supply etc. caused high economic losses in the region. To mitigate future tsunami impacts there is a need to assess the tsunami hazard and vulnerability in flood prone areas at the Andaman Sea coast in order to determine the spatial distribution of risk and to develop risk management strategies. In the bilateral German-Thai project TRAIT research is performed on integrated risk assessment for the Provinces Phang Nga and Phuket in southern Thailand, including a hazard analysis, i.e. modelling tsunami propagation to the coast, tsunami wave breaking and inundation characteristics, as well as vulnerability analysis of the socio-economic and the ecological system in order to determine the scenario-based, specific risk for the region. In this presentation results of the hazard analysis and the inundation simulation are presented and discussed. Numerical modelling of tsunami propagation and inundation simulation is an inevitable tool for risk analysis, risk management and evacuation planning. While numerous investigations have been made to model tsunami wave generation and propagation in the Indian Ocean, there is still a lack in determining detailed inundation patterns, i.e. water depth and flow dynamics. However, for risk management and evacuation planning this knowledge is essential. As the accuracy of the inundation simulation is strongly depending on the available bathymetric and the topographic data, a multi-scale approach is chosen in this work. The ETOPO Global Relief Model as a bathymetric basis and the Shuttle Radar Topography Mission (SRTM90) have been widely applied in tsunami modelling approaches as these data are free and almost world

Flood-inundation maps for North Fork Salt Creek at Nashville, Indiana

Science.gov (United States)

Martin, Zachary W.

2017-11-13

Digital flood-inundation maps for a 3.2-mile reach of North Fork Salt Creek at Nashville, Indiana, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science website at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding that correspond to selected water levels (stages) at the North Fork Salt Creek at Nashville, Ind., streamgage (USGS station number 03371650). Real-time stages at this streamgage may be obtained from the USGS National Water Information System at http://waterdata.usgs.gov/nwis or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at http:/water.weather.gov/ahps/, which also shows observed USGS stages at the same site as the USGS streamgage (NWS site NFSI3).Flood profiles were computed for the stream reach by means of a one-dimensional, step-backwater hydraulic modeling software developed by the U.S. Army Corps of Engineers. The hydraulic model was calibrated using the current (2015) stage-discharge rating at the USGS streamgage 03371650, North Fork Salt Creek at Nashville, Ind. The hydraulic model was then used to compute 12 water-surface profiles for flood stages at 1-foot (ft) intervals, except for the highest profile of 22.9 ft, referenced to the streamgage datum ranging from 12.0 ft (the NWS “action stage”) to 22.9 ft, which is the highest stage of the current (2015) USGS stage-discharge rating curve and 1.9 ft higher than the NWS “major flood stage.” The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from light detection and ranging data having a 0.98-ft vertical accuracy and 4.9-ft horizontal resolution) to delineate the area flooded at each stage.The availability of these maps, along with information regarding current stage from the USGS

Towards an integrated strategy for monitoring wetland inundation with virtual constellations of optical and radar satellites

Science.gov (United States)

DeVries, B.; Huang, W.; Huang, C.; Jones, J. W.; Lang, M. W.; Creed, I. F.; Carroll, M.

2017-12-01

The function of wetlandscapes in hydrological and biogeochemical cycles is largely governed by surface inundation, with small wetlands that experience periodic inundation playing a disproportionately large role in these processes. However, the spatial distribution and temporal dynamics of inundation in these wetland systems are still poorly understood, resulting in large uncertainties in global water, carbon and greenhouse gas budgets. Satellite imagery provides synoptic and repeat views of the Earth's surface and presents opportunities to fill this knowledge gap. Despite the proliferation of Earth Observation satellite missions in the past decade, no single satellite sensor can simultaneously provide the spatial and temporal detail needed to adequately characterize inundation in small, dynamic wetland systems. Surface water data products must therefore integrate observations from multiple satellite sensors in order to address this objective, requiring the development of improved and coordinated algorithms to generate consistent estimates of surface inundation. We present a suite of algorithms designed to detect surface inundation in wetlands using data from a virtual constellation of optical and radar sensors comprising the Landsat and Sentinel missions (DeVries et al., 2017). Both optical and radar algorithms were able to detect inundation in wetlands without the need for external training data, allowing for high-efficiency monitoring of wetland inundation at large spatial and temporal scales. Applying these algorithms across a gradient of wetlands in North America, preliminary findings suggest that while these fully automated algorithms can detect wetland inundation at higher spatial and temporal resolutions than currently available surface water data products, limitations specific to the satellite sensors and their acquisition strategies are responsible for uncertainties in inundation estimates. Further research is needed to investigate strategies for

THE SAMOA TSUNAMI OF 29 SEPTEMBER 2009 Early Warning and Inundation Assessment

Directory of Open Access Journals (Sweden)

Giovanni Franchello

2012-01-01

Full Text Available On 29 September 2009 at 17:48:11 UTC, a large earthquake of magnitude 8 struck off-shore of the Samoa Islands and generated a large tsunami that destroyed several villages and caused more than 160 fatalities. This report first presents the characteristics of the earthquake and discusses the best estimations for the fault parameters, which are the necessary input data for the hydrodynamic tsunami calculations. Then, the assessment of the near-real time systems invoked by the Global Disasters Alert and Coordination System (GDACS1 and the post-event calculations are performed, making comparisons with the observed tidal measurements and post-event survey. It was found that the most severely damaged locations are the Southern section of the Western Samoa Islands, Tutuila Isl in American Samoa and Niuatoputapu Isle in Tonga. This is in agreement with the locations indicated by the Red Cross as the most affected and with the results of the post-tsunami surveys. Furthermore, an attempt was made to map the inundation events using more detailed digital elevation models (DEM and hydrodynamic modelling with good results. The flooded areas for which we had satellite images and post-tsunami surveys confirm the inundated areas identified correctly by the hydrodynamic model. Indications are given on the DEM grid size needed for the different simulations.

Developing an Event-Tree Probabilistic Tsunami Inundation Model for NE Atlantic Coasts: Application to a Case Study

Science.gov (United States)

Omira, R.; Matias, L.; Baptista, M. A.

2016-12-01

This study constitutes a preliminary assessment of probabilistic tsunami inundation in the NE Atlantic region. We developed an event-tree approach to calculate the likelihood of tsunami flood occurrence and exceedance of a specific near-shore wave height for a given exposure time. Only tsunamis of tectonic origin are considered here, taking into account local, regional, and far-field sources. The approach used here consists of an event-tree method that gathers probability models for seismic sources, tsunami numerical modeling, and statistical methods. It also includes a treatment of aleatoric uncertainties related to source location and tidal stage. Epistemic uncertainties are not addressed in this study. The methodology is applied to the coastal test-site of Sines located in the NE Atlantic coast of Portugal. We derive probabilistic high-resolution maximum wave amplitudes and flood distributions for the study test-site considering 100- and 500-year exposure times. We find that the probability that maximum wave amplitude exceeds 1 m somewhere along the Sines coasts reaches about 60 % for an exposure time of 100 years and is up to 97 % for an exposure time of 500 years. The probability of inundation occurrence (flow depth >0 m) varies between 10 % and 57 %, and from 20 % up to 95 % for 100- and 500-year exposure times, respectively. No validation has been performed here with historical tsunamis. This paper illustrates a methodology through a case study, which is not an operational assessment.

Modeling Surface Water Dynamics in the Amazon Basin Using Mosart-Inundation-v1.0: Impacts of Geomorphological Parameters and River Flow Representation

Science.gov (United States)

Luo, Xiangyu; Li, Hong-Yi; Leung, Ruby; Tesfa, Teklu K.; Getirana, Augusto; Papa, Fabrice; Hess, Laura L.

2017-01-01

Surface water dynamics play an important role in water, energy and carbon cycles of the Amazon Basin. A macro-scale inundation scheme was integrated with a surface-water transport model and the extended model was applied in this vast basin. We addressed the challenges of improving basin-wide geomorphological parameters and river flow representation for 15 large-scale applications. Vegetation-caused biases embedded in the HydroSHEDS DEM data were alleviated by using a vegetation height map of about 1-km resolution and a land cover dataset of about 90-m resolution. The average elevation deduction from the DEM correction was about 13.2 m for the entire basin. Basin-wide empirical formulae for channel cross-sectional geometry were adjusted based on local information for the major portion of the basin, which could significantly reduce the cross-sectional area for the channels of some subregions. The Manning roughness coefficient of the channel 20 varied with the channel depth to reflect the general rule that the relative importance of riverbed resistance in river flow declined with the increase of river size. The entire basin was discretized into 5395 subbasins (with an average area of 1091.7 km2), which were used as computation units. The model was driven by runoff estimates of 14 years (1994 2007) generated by the ISBA land surface model. The simulated results were evaluated against in situ streamflow records, and remotely sensed Envisat altimetry data and GIEMS inundation data. The hydrographs were reproduced fairly well for the majority of 25 13 major stream gauges. For the 11 subbasins containing or close to 11 of the 13 gauges, the timing of river stage fluctuations was captured; for most of the 11 subbasins, the magnitude of river stage fluctuations was represented well. The inundation estimates were comparable to the GIEMS observations. Sensitivity analyses demonstrated that refining floodplain topography, channel morphology and Manning roughness coefficients

Monitoring coastal inundation with Synthetic Aperture Radar satellite data

Science.gov (United States)

Suzuoki, Yukihiro; Rangoonwala, Amina; Ramsey, Elijah W.

2011-01-01

Maps representing the presence and absence of surface inundation in the Louisiana coastal zone were created from available satellite scenes acquired by the Japanese Aerospace Exploration Agency's Advanced Land Observing Satellite and by the European Space Agency's Envisat from late 2006 through summer 2009. Detection of aboveground surface flooding relied on the well-documented and distinct signature of decreased backscatter in Synthetic Aperture Radar (SAR), which is indicative of inundated marsh in the Gulf of Mexico. Even though decreases in backscatter were distinctive, the multiplicity of possible interactions between changing flood depths and canopy height yielded complex SAR-based representations of the marshes.

Development of Urban Inundation Warning Model at Cyclic Artificial Water Way in Song-do International City, Republic of Korea

Science.gov (United States)

Lee, T.; Lee, C.; Kim, H.

2016-12-01

Abstract Song-do international city was constructed by reclaiming land from the coastal waters of Yeonsu-gu, Incheon Metropolitan City, Republic of Korea. The □-shaped cyclic artificial water way has been considered for improving water quality, waterfront and internal drainage in Song-do international city. By improving water quality, various marine facilities, such as marina, artificial beach, marine terminal, and so on, will be set up around the artificial water way for the waterfront. Since the water stage of the artificial water way changes depending on water gates operations, it is necessary to develop an urban inundation warning model to evaluate safeties of the waterfront facilities and its passengers. By considering characteristics of urban watershed, we calculate discharge flowing into the water way using XP-SWMM model. As a result of estimating 100-year flood frequency, although there are slight differences in drainage sections, the maximum flood discharge occurs in 90-min rainfall duration. In order to consider impacts of tide and hydraulic structure, we establish Inland drainage plans through the analysis of unsteady flow using HEC-RAS. The urban inundation warning model is configured to issue a warning when the water plain elevation exceeds EL. 1.5m which is usually managed at EL. 1.0m. In this study, the design flood stage of artificial water way and urban inundation warning model are developed for Song-do international city, and therefore it is expected that a reliability of management and operation of the waterfront facilities is improved. Keywords : Artificial Water Way; Waterfront; Urban Inundation Warning Model. Acknowlegement This research was supported by a grant [MPSS-NH-2015-79] through the Disaster and Safety Management Institute funded by Ministry of Public Safety and Security of Korean government.

Statistics of the first passage time of Brownian motion conditioned by maximum value or area

International Nuclear Information System (INIS)

Kearney, Michael J; Majumdar, Satya N

2014-01-01

We derive the moments of the first passage time for Brownian motion conditioned by either the maximum value or the area swept out by the motion. These quantities are the natural counterparts to the moments of the maximum value and area of Brownian excursions of fixed duration, which we also derive for completeness within the same mathematical framework. Various applications are indicated. (paper)

High Resolution Modeling of Coastal Inundation: User Requirements and Current Practice, A Navy Perspective

National Research Council Canada - National Science Library

Blain, Cheryl Ann; Preller, Ruth H

2007-01-01

The impact of coastal flooding and inundation on Navy operational missions and the existing Navy requirements for resolution and accuracy relevant to coastal inundation are presented. High resolution (less than 500 m...

Interactive Mapping of Inundation Metrics Using Cloud Computing for Improved Floodplain Conservation and Management

Science.gov (United States)

Bulliner, E. A., IV; Lindner, G. A.; Bouska, K.; Paukert, C.; Jacobson, R. B.

2017-12-01

Within large-river ecosystems, floodplains serve a variety of important ecological functions. A recent survey of 80 managers of floodplain conservation lands along the Upper and Middle Mississippi and Lower Missouri Rivers in the central United States found that the most critical information needed to improve floodplain management centered on metrics for characterizing depth, extent, frequency, duration, and timing of inundation. These metrics can be delivered to managers efficiently through cloud-based interactive maps. To calculate these metrics, we interpolated an existing one-dimensional hydraulic model for the Lower Missouri River, which simulated water surface elevations at cross sections spaced (step. To translate these water surface elevations to inundation depths, we subtracted a merged terrain model consisting of floodplain LIDAR and bathymetric surveys of the river channel. This approach resulted in a 29000+ day time series of inundation depths across the floodplain using grid cells with 30 m spatial resolution. Initially, we used these data on a local workstation to calculate a suite of nine spatially distributed inundation metrics for the entire model domain. These metrics are calculated on a per pixel basis and encompass a variety of temporal criteria generally relevant to flora and fauna of interest to floodplain managers, including, for example, the average number of days inundated per year within a growing season. Using a local workstation, calculating these metrics for the entire model domain requires several hours. However, for the needs of individual floodplain managers working at site scales, these metrics may be too general and inflexible. Instead of creating a priori a suite of inundation metrics able to satisfy all user needs, we present the usage of Google's cloud-based Earth Engine API to allow users to define and query their own inundation metrics from our dataset and produce maps nearly instantaneously. This approach allows users to

Flood-inundation maps for Suwanee Creek from the confluence of Ivy Creek to the Noblin Ridge Drive bridge, Gwinnett County, Georgia

Science.gov (United States)

Musser, Jonathan W.

2012-01-01

Digital flood-inundation maps for a 6.9-mile reach of Suwanee Creek, from the confluence of Ivy Creek to the Noblin Ridge Drive bridge, were developed by the U.S. Geological Survey (USGS) in cooperation with Gwinnett County, Georgia. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at Suwanee Creek at Suwanee, Georgia (02334885). Current stage at this USGS streamgage may be obtained at http://waterdata.usgs.gov/ and can be used in conjunction with these maps to estimate near real-time areas of inundation. The National Weather Service (NWS) is incorporating results from this study into the Advanced Hydrologic Prediction Service (AHPS) flood-warning system (http://water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that commonly are collocated at USGS streamgages. The forecasted peak-stage information for the USGS streamgage at Suwanee Creek at Suwanee (02334885), available through the AHPS Web site, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. A one-dimensional step-backwater model was developed using the U.S. Army Corps of Engineers HEC-RAS software for Suwanee Creek and was used to compute flood profiles for a 6.9-mile reach of the creek. The model was calibrated using the most current stage-discharge relations at the Suwanee Creek at Suwanee streamgage (02334885). The hydraulic model was then used to determine 19 water-surface profiles for flood stages at the Suwanee Creek streamgage at 0.5-foot intervals referenced to the streamgage. The profiles ranged from just above bankfull stage (7.0 feet) to approximately 1.7 feet above the highest recorded water level at the streamgage (16.0 feet). The simulated water-surface profiles were then combined

Selection of Trichogramma for inundative biological control

NARCIS (Netherlands)

Pak, G.A.

1988-01-01

This thesis presents a study of the potential for biological control of lepidopterous pests on cabbage crops in the Netherlands, by means of inundative releases of the egg parasite Trichogramma (Hymenoptera, Trichogrammatidae). The objective of this study is to investigate the

Flood-inundation maps for the Mississinewa River at Marion, Indiana, 2013

Science.gov (United States)

Coon, William F.

2014-01-01

Digital flood-inundation maps for a 9-mile (mi) reach of the Mississinewa River from 0.75 mi upstream from the Pennsylvania Street bridge in Marion, Indiana, to 0.2 mi downstream from State Route 15 were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Office of Community and Rural Affairs. The flood inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage on the Mississinewa River at Marion (station number 03326500). Near-real-time stages at this streamgage may be obtained on the Internet from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at http://water.weather.gov/ahps/, which also forecasts flood hydrographs at this site. Flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated by using the current stage-discharge relation at the Mississinewa River streamgage, in combination with water-surface profiles from historic floods and from the current (2002) flood-insurance study for Grant County, Indiana. The hydraulic model was then used to compute seven water-surface profiles for flood stages at 1-fo (ft) intervals referenced to the streamgage datum and ranging from 10 ft, which is near bankfull, to 16 ft, which is between the water levels associated with the estimated 10- and 2-percent annual exceedance probability floods (floods with recurrence interval between 10 and 50 years) and equals the “major flood stage” as defined by the NWS. The simulated water-surface profiles were then combined with a Geographic Information System digital elevation model (derived from light detection and ranging (lidar) data having a 0.98 ft vertical accuracy and 4.9 ft

Inundation, sedimentation, and subsidence creates goose habitat along the Arctic coast of Alaska

Science.gov (United States)

Tape, Ken D.; Flint, Paul L.; Meixell, Brandt W.; Gaglioti, Benjamin V.

2013-01-01

The Arctic Coastal Plain of Alaska is characterized by thermokarst lakes and drained lake basins, and the rate of coastal erosion has increased during the last half-century. Portions of the coast are sea level for kilometers inland, and are underlain by ice-rich permafrost. Increased storm surges or terrestrial subsidence would therefore expand the area subject to marine inundation. Since 1976, the distribution of molting Black Brant (Branta bernicla nigricans) on the Arctic Coastal Plain has shifted from inland freshwater lakes to coastal marshes, such as those occupying the Smith River and Garry Creek estuaries. We hypothesized that the movement of geese from inland lakes was caused by an expansion of high quality goose forage in coastal areas. We examined the recent history of vegetation and geomorphological changes in coastal goose habitat by combining analysis of time series imagery between 1948 and 2010 with soil stratigraphy dated using bomb-curve radiocarbon. Time series of vertical imagery and in situ verification showed permafrost thaw and subsidence of polygonal tundra. Soil stratigraphy and dating within coastal estuaries showed that non-saline vegetation communities were buried by multiple sedimentation episodes between 1948 and 1995, accompanying a shift toward salt-tolerant vegetation. This sedimentation allowed high quality goose forage plants to expand, thus facilitating the shift in goose distribution. Declining sea ice and the increasing rate of terrestrial inundation, sedimentation, and subsidence in coastal estuaries of Alaska may portend a 'tipping point' whereby inland areas would be transformed into salt marshes.

Experience of inundation or drought alters the responses of plants to subsequent water conditions

DEFF Research Database (Denmark)

Wang, Shu; Callaway, Ragan M.; Zhou, Dao-Wei

2017-01-01

had the strongest drought tolerance after early drought; (iii) mesic species were more likely to suffer reduced later growth after either inundation or drought experience. Invasive species benefitted more from early inundation than did native species, but native species grew better after experiencing...

Inundation, run-up heights, cross-section profiles and littoral environment along the Tamil Nadu coast after 26 th December 2004 Tsunami

Digital Repository Service at National Institute of Oceanography (India)

Ilangovan, D.; Jayakumar, S.; Gowthaman, R.; Tirodkar, G.; Ganesan, P.; Naik, G.N.; ManiMurali, R.; Michael, G.S.; Ramana, M.V.; Naik, K.A.

of Oceanography (NIO) and under the leadership of Dr. G. C. Battacharya, Scientist F, NIO,) surveys were carried out along several coastal areas of India for eliciting information about the inundation and several related aspects of the Tsunami. Different locations...

Development of a model to simulate groundwater inundation induced by sea-level rise and high tides in Honolulu, Hawaii.

Science.gov (United States)

Habel, Shellie; Fletcher, Charles H; Rotzoll, Kolja; El-Kadi, Aly I

2017-05-01

Many of the world's largest cities face risk of sea-level rise (SLR) induced flooding owing to their limited elevations and proximities to the coastline. Within this century, global mean sea level is expected to reach magnitudes that will exceed the ground elevation of some built infrastructure. The concurrent rise of coastal groundwater will produce additional sources of inundation resulting from narrowing and loss of the vertical unsaturated subsurface space. This has implications for the dense network of buried and low-lying infrastructure that exists across urban coastal zones. Here, we describe a modeling approach that simulates narrowing of the unsaturated space and groundwater inundation (GWI) generated by SLR-induced lifting of coastal groundwater. The methodology combines terrain modeling, groundwater monitoring, estimation of tidal influence, and numerical groundwater-flow modeling to simulate future flood scenarios considering user-specified tide stages and magnitudes of SLR. We illustrate the value of the methodology by applying it to the heavily urbanized and low-lying Waikiki area of Honolulu, Hawaii. Results indicate that SLR of nearly 1 m generates GWI across 23% of the 13 km 2 study area, threatening $5 billion of taxable real estate and 48 km of roadway. Analysis of current conditions reveals that 86% of 259 active cesspool sites in the study area are likely inundated. This suggests that cesspool effluent is currently entering coastal groundwater, which not only leads to degradation of coastal environments, but also presents a future threat to public health as GWI would introduce effluent at the ground surface. Copyright © 2017 Elsevier Ltd. All rights reserved.

Palm Swamp Wetland Ecosystems of the Upper Amazon: Characterizing their Distribution and Inundation State Using Multiple Resolution Microwave Remote Sensing

Science.gov (United States)

Podest, E.; McDonald, K. C.; Schröder, R.; Pinto, N.; Zimmermann, R.; Horna, V.

2011-12-01

Palm swamp wetlands are prevalent in the Amazon basin, including extensive regions in northern Peru. These ecosystems are characterized by constant surface inundation and moderate seasonal water level variation. The combination of constantly saturated soils, giving rise to low oxygen conditions, and warm temperatures year-round can lead to considerable methane release to the atmosphere. Because of the widespread occurrence and expected sensitivity of these ecosystems to climate change, knowledge of their spatial extent and inundation state is crucial for assessing the associated land-atmosphere carbon exchange. Precise spatio-temporal information on palm swamps is difficult to gather because of their remoteness and difficult accessibility. Spaceborne microwave remote sensing is an effective tool for characterizing these ecosystems since it is sensitive to surface water and vegetation structure and allows monitoring large inaccessible areas on a temporal basis regardless of atmospheric conditions or solar illumination. We are developing a remote sensing methodology using multiple resolution microwave remote sensing data to determine palm swamp distribution and inundation state over focus regions in the Amazon basin in northern Peru. For this purpose, two types of multi-temporal microwave data are used: 1) high-resolution (100 m) data from the Advanced Land Observing Satellite (ALOS) Phased Array L-Band Synthetic Aperture Radar (PALSAR) to derive maps of palm swamp extent and inundation from dual-polarization fine-beam and multi-temporal HH-polarized ScanSAR, and 2) coarse resolution (25 km) combined active and passive microwave data from QuikSCAT and AMSR-E to derive inundated area fraction on a weekly basis. We compare information content and accuracy of the coarse resolution products to the PALSAR-based datasets to ensure information harmonization. The synergistic combination of high and low resolution datasets will allow for characterization of palm swamps and

Dam-breach analysis and flood-inundation mapping for selected dams in Oklahoma City, Oklahoma, and near Atoka, Oklahoma

Science.gov (United States)

Shivers, Molly J.; Smith, S. Jerrod; Grout, Trevor S.; Lewis, Jason M.

2015-01-01

Dams provide beneficial functions such as flood control, recreation, and storage of water supplies, but they also entail risk; dam breaches and resultant floods can cause substantial property damage and loss of life. The State of Oklahoma requires each owner of a high-hazard dam, which the Federal Emergency Management Agency defines as dams for which failure or improper operation probably will cause loss of human life, to develop an emergency action plan specific to that dam. Components of an emergency action plan are to simulate a flood resulting from a possible dam breach and map the resulting downstream flood-inundation areas. The resulting flood-inundation maps can provide valuable information to city officials, emergency managers, and local residents for planning an emergency response if a dam breach occurs.

Flood-inundation maps for the Wabash River at Memorial Bridge at Vincennes, Indiana

Science.gov (United States)

Fowler, Kathleen K.; Menke, Chad D.

2017-08-23

Digital flood-inundation maps for a 10.2-mile reach of the Wabash River from Sevenmile Island to 3.7 mile downstream of Memorial Bridge (officially known as Lincoln Memorial Bridge) at Vincennes, Indiana, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Office of Community and Rural Affairs. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at USGS streamgage 03343010, Wabash River at Memorial Bridge at Vincennes, Ind. Near-real-time stages at this streamgage may be obtained on the Internet from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at http:/water.weather.gov/ahps/, which also forecasts flood hydrographs at this site.For this study, flood profiles were computed for the Wabash River reach by means of a one-dimensional stepbackwater model. The hydraulic model was calibrated by using the most current stage-discharge relations at USGS streamgage 03343010, Wabash River at Memorial Bridge at Vincennes, Ind., and preliminary high-water marks from a high-water event on April 27, 2013. The calibrated hydraulic model was then used to determine 19 water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datum and ranging from 10 feet (ft) or near bankfull to 28 ft, the highest stage of the current stage-discharge rating curve. The simulated water-surface profiles were then combined with a Geographic Information System (GIS) digital elevation model (DEM, derived from Light Detection and Ranging [lidar] data having a 0.98-ft vertical accuracy and 4.9-ft horizontal resolution) in order to delineate the area flooded at each water level.The availability of these maps—along with Internet information

Flood-inundation maps for Cedar Creek at 18th Street at Auburn, Indiana

Science.gov (United States)

Fowler, Kathleen K.

2018-02-27

Digital flood-inundation maps for a 1.9-mile reach of Cedar Creek at Auburn, Indiana (Ind.), from the First Street bridge, downstream to the streamgage at 18th Street, then ending approximately 1,100 feet (ft) downstream of the Baltimore and Ohio railroad, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science web site at https://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage on Cedar Creek at 18th Street at Auburn, Ind. (station number 04179520). Near-real-time stages at this streamgage may be obtained from the USGS National Water Information System at https://waterdata.usgs.gov/ or the National Weather Service Advanced Hydrologic Prediction Service at http://water.weather.gov/ahps/, although forecasts of flood hydrographs are not available at this site (ABBI3).Flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The hydraulic model was calibrated by using the most current stage-discharge relation at the Cedar Creek at 18th Street at Auburn, Ind. streamgage and the documented high-water marks from the flood of March 11, 2009. The calibrated hydraulic model was then used to compute seven water-surface profiles for flood stages referenced to the streamgage datum and ranging from 7 ft, or near bankfull, to 13 ft, in 1-foot increments. The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from light detection and ranging [lidar] data having a 0.98-ft vertical accuracy and 4.9-ft horizontal resolution) to delineate the area flooded at each water level.The availability of these maps, along with internet information regarding current stage from the USGS streamgage at Cedar Creek

Impacts of Coastal Inundation Due to Climate Change in a CLUSTER of Urban Coastal Communities in Ghana, West Africa

Directory of Open Access Journals (Sweden)

Patrick Kwabena Ofori-Danson

2011-09-01

Full Text Available The increasing rates of sea level rise caused by global warming within the 21st century are expected to exacerbate inundation and episodic flooding tide in low-lying coastal environments. This development threatens both human development and natural habitats within such coastal communities. The impact of sea level rise will be more pronounced in developing countries where there is limited adaptation capacity. This paper presents a comprehensive assessment of the expected impacts of sea level rise in three communities in the Dansoman coastal area of Accra, Ghana. Future sea level rises were projected based on global scenarios and the Commonwealth Scientific and Industrial Research Organization General Circulation Models—CSIRO_MK2_GS GCM. These were used in the SimCLIM model based on the modified Bruun rule and the simulated results overlaid on near vertical aerial photographs taken in 2005. It emerged that the Dansoman coastline could recede by about 202 m by the year 2100 with baseline from 1970 to 1990. The potential impacts on the socioeconomic and natural systems of the Dansoman coastal area were characterized at the Panbros, Grefi and Gbegbeyise communities. The study revealed that about 84% of the local dwellers is aware of the rising sea level in the coastal area but have poor measures of adapting to the effects of flood disasters. Analysis of the likely impacts of coastal inundation revealed that about 650,000 people, 926 buildings and a total area of about 0.80 km2 of land are vulnerable to permanent inundation by the year 2100. The study has shown that there will be significant losses to both life and property by the year 2100 in the Dansoman coastal community in the event of sea level rise.

Measuring Sea Level Rise-Induced Shoreline Changes and Inundation in Real Time

Science.gov (United States)

Shilling, F.; Waetjen, D.; Grijalva, E.

2016-12-01

We describe a method to monitor shoreline inundation and changes in response to sea level rise (SLR) using a network of time-lapse cameras. We found for coastal tidal marshes that this method was sensitive to vertical changes in sea level of 20 cm has occurred in the San Francisco Bay and other US coastal areas and is likely to rise by another 30-45 cm by mid-century, which will flood and erode many coastal ecosystems, highways, and urban areas. This rapid degree of rise means that it is imperative to co-plan for natural and built systems. Many public facilities are adjacent to shoreline ecosystems, which both protect infrastructure from wave and tide energy and are home to regulated species and habitats. Accurate and timely information about the actual extent of SLR impacts to shorelines will be critical during built-system adaptation. Currently, satellite-sourced imagery cannot provide the spatial or temporal resolution necessary to investigate fine-scale shoreline changes, leaving a gap between predictive models and knowing how, where and when these changes are occurring. The method described is feasible for near-term (1 to 10 years) to long-term application and can be used for measuring fine-resolution shoreline changes (organize photographs that could be combined with related external data (e.g., gauged water levels) to create an information mashup. This information could be used to validate models predicting shoreline inundation and loss, inform SLR-adaptation planning, and to visualize SLR impacts to the public.

Method for estimating potential wetland extent by utilizing streamflow statistics and flood-inundation mapping techniques: Pilot study for land along the Wabash River near Terre Haute, Indiana

Science.gov (United States)

Kim, Moon H.; Ritz, Christian T.; Arvin, Donald V.

2012-01-01

Potential wetland extents were estimated for a 14-mile reach of the Wabash River near Terre Haute, Indiana. This pilot study was completed by the U.S. Geological Survey in cooperation with the U.S. Department of Agriculture, Natural Resources Conservation Service (NRCS). The study showed that potential wetland extents can be estimated by analyzing streamflow statistics with the available streamgage data, calculating the approximate water-surface elevation along the river, and generating maps by use of flood-inundation mapping techniques. Planning successful restorations for Wetland Reserve Program (WRP) easements requires a determination of areas that show evidence of being in a zone prone to sustained or frequent flooding. Zone determinations of this type are used by WRP planners to define the actively inundated area and make decisions on restoration-practice installation. According to WRP planning guidelines, a site needs to show evidence of being in an "inundation zone" that is prone to sustained or frequent flooding for a period of 7 consecutive days at least once every 2 years on average in order to meet the planning criteria for determining a wetland for a restoration in agricultural land. By calculating the annual highest 7-consecutive-day mean discharge with a 2-year recurrence interval (7MQ2) at a streamgage on the basis of available streamflow data, one can determine the water-surface elevation corresponding to the calculated flow that defines the estimated inundation zone along the river. By using the estimated water-surface elevation ("inundation elevation") along the river, an approximate extent of potential wetland for a restoration in agricultural land can be mapped. As part of the pilot study, a set of maps representing the estimated potential wetland extents was generated in a geographic information system (GIS) application by combining (1) a digital water-surface plane representing the surface of inundation elevation that sloped in the downstream

Remote Sensing of River Delta Inundation: Exploiting the Potential of Coarse Spatial Resolution, Temporally-Dense MODIS Time Series

Directory of Open Access Journals (Sweden)

Claudia Kuenzer

2015-07-01

Full Text Available River deltas belong to the most densely settled places on earth. Although they only account for 5% of the global land surface, over 550 million people live in deltas. These preferred livelihood locations, which feature flat terrain, fertile alluvial soils, access to fluvial and marine resources, a rich wetland biodiversity and other advantages are, however, threatened by numerous internal and external processes. Socio-economic development, urbanization, climate change induced sea level rise, as well as flood pulse changes due to upstream water diversion all lead to changes in these highly dynamic systems. A thorough understanding of a river delta’s general setting and intra-annual as well as long-term dynamic is therefore crucial for an informed management of natural resources. Here, remote sensing can play a key role in analyzing and monitoring these vast areas at a global scale. The goal of this study is to demonstrate the potential of intra-annual time series analyses at dense temporal, but coarse spatial resolution for inundation characterization in five river deltas located in four different countries. Based on 250 m MODIS reflectance data we analyze inundation dynamics in four densely populated Asian river deltas—namely the Yellow River Delta (China, the Mekong Delta (Vietnam, the Irrawaddy Delta (Myanmar, and the Ganges-Brahmaputra (Bangladesh, India—as well as one very contrasting delta: the nearly uninhabited polar Mackenzie Delta Region in northwestern Canada for the complete time span of one year (2013. A complex processing chain of water surface derivation on a daily basis allows the generation of intra-annual time series, which indicate inundation duration in each of the deltas. Our analyses depict distinct inundation patterns within each of the deltas, which can be attributed to processes such as overland flooding, irrigation agriculture, aquaculture, or snowmelt and thermokarst processes. Clear differences between mid

Advanced Regional and Decadal Predictions of Coastal Inundation for the U.S. Atlantic and Gulf Coasts (Invited)

Science.gov (United States)

Horton, B.; Corbett, D. R.; Donnelly, J. P.; Kemp, A.; Lin, N.; Lindeman, K.; Mann, M. E.; Peltier, W. R.; Rahmstorf, S.

2013-12-01

Future inundation of the U.S. Atlantic and Gulf coasts will depend upon sea-level rise and the intensity and frequency of tropical cyclones, each of which will be affected by climate change. Through ongoing, collaborative research we are employing new interdisciplinary approaches to bring about a step change in the reliability of predictions of such inundation. The rate of sea level rise along the U.S. Atlantic and Gulf coasts increased throughout the 20th century. Whilst there is widespread agreement that it continue to accelerate during the 21st century, great uncertainty surrounds its magnitude and geographic variability. Key uncertainties include the role of continental ice sheets, mountain glaciers, and ocean density changes. Insufficient understanding of these complex physical processes precludes accurate prediction of sea-level rise. New approaches using semi-empirical models that relate instrumental records of climate and sea-level rise have projected up to 2 m of sea-level rise by AD 2100. But the time span of instrumental sea-level records is insufficient to adequately constrain the climate:sea-level relationship. We produced new, high-resolution proxy sea-level reconstructions to provide crucial additional constraints to such semi-empirical models. Our dataset spans the alternation between the 'Medieval Climate Anomaly' and 'Little Ice Age'. Before the models can provide appropriate data for coastal management and planning, they must be complemented with regional estimates of sea-level rise. Therefore, the proxy sea-level data has been collected from four study areas (Connecticut, New Jersey, North Carolina and Florida) to accommodate the required extent of regional variability. In the case of inundation arising from tropical cyclones, the historical and observational records are insufficient for predicting their nature and recurrence, because they are such extreme and rare events. Moreover, future storm surges will be superimposed on background sea

Geological record of tsunami inundations in Pantano Morghella (south-eastern Sicily both from near and far-field sources

Directory of Open Access Journals (Sweden)

F. Gerardi

2012-04-01

Full Text Available Analysis of tsunami deposits from the Pantano Morghella area provided geological evidence for two inundations occurred along the south-eastern Ionian coast of Sicily. Pantano Morghella is a large pond characterised by a fine-grained sedimentation indicating a low-energy depositional environment. Two anomalous yellow sandy layers found at different depths indicate the occurrence of high-energy marine inundations. We studied sedimentological and paleontological features of the anomalous deposits as well as their spatial distribution observing the following properties: different facies with respect to the local stratigraphic sequence; erosive bases, rip-up clasts and broken elements testifying violent deposition mechanisms; macro and micro fauna of marine environment; relatively constant thickness throughout most of the depositional zone with thinning at the distal end; large sand sheets that extend inland. These observations, jointly with their infrequency in the sedimentary record and the age indicating a fast deposition, provided strong evidence for tsunami inundations. Correlations between anomalous layers and historical tsunamis are supported by radiocarbon and OSL dating results. The younger deposit is likely due to the 1908 near-source tsunami, whereas the flooding of the oldest event is most likely associated with a far and large source, the Crete 365 AD earthquake.

Development of a hydraulic model and flood-inundation maps for the Wabash River near the Interstate 64 Bridge near Grayville, Illinois

Science.gov (United States)

Boldt, Justin A.

2018-01-16

A two-dimensional hydraulic model and digital flood‑inundation maps were developed for a 30-mile reach of the Wabash River near the Interstate 64 Bridge near Grayville, Illinois. The flood-inundation maps, which can be accessed through the U.S. Geological Survey (USGS) Flood Inundation Mapping Science web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage on the Wabash River at Mount Carmel, Ill (USGS station number 03377500). Near-real-time stages at this streamgage may be obtained on the internet from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service (NWS) Advanced Hydrologic Prediction Service (AHPS) at http://water.weather.gov/ahps/, which also forecasts flood hydrographs at this site (NWS AHPS site MCRI2). The NWS AHPS forecasts peak stage information that may be used with the maps developed in this study to show predicted areas of flood inundation.Flood elevations were computed for the Wabash River reach by means of a two-dimensional, finite-volume numerical modeling application for river hydraulics. The hydraulic model was calibrated by using global positioning system measurements of water-surface elevation and the current stage-discharge relation at both USGS streamgage 03377500, Wabash River at Mount Carmel, Ill., and USGS streamgage 03378500, Wabash River at New Harmony, Indiana. The calibrated hydraulic model was then used to compute 27 water-surface elevations for flood stages at 1-foot (ft) intervals referenced to the streamgage datum and ranging from less than the action stage (9 ft) to the highest stage (35 ft) of the current stage-discharge rating curve. The simulated water‑surface elevations were then combined with a geographic information system digital elevation model, derived from light detection and ranging data, to delineate the area flooded at each water

The effect of inundation frequency on ground beetle communities in a channelized mountain stream

Science.gov (United States)

Skalski, T.; Kedzior, R.; Radecki-Pawlik, A.

2012-04-01

size distribution of ground beetles is significantly right skewed on more frequently flooded areas whereas on more stable localities it becomes left skewed. Our results also demonstrated that the presence of ERS does not changes the structure of ground beetle communities if the frequency of inundation of river banks is reduced. This study indicated that not only habitat parameters but also biotic interactions between competing species from a regional pool are important for the conservation of riverine communities. Vulnerable beetles characteristic of riverine habitats are small and usually weak competitors. A reduced frequency of bank inundation creates possibilities for the colonization of ERS by species from surrounding habitats and elimination of the species well adapted to the dynamic flow conditions typifying unmodified stream sections.

The Hengill geothermal area, Iceland: Variation of temperature gradients deduced from the maximum depth of seismogenesis

Science.gov (United States)

Foulger, G. R.

1995-04-01

Given a uniform lithology and strain rate and a full seismic data set, the maximum depth of earthquakes may be viewed to a first order as an isotherm. These conditions are approached at the Hengill geothermal area S. Iceland, a dominantly basaltic area. The likely strain rate calculated from thermal and tectonic considerations is 10 -15 s -1, and temperature measurements from four drill sites within the area indicate average, near-surface geothermal gradients of up to 150 °C km -1 throughout the upper 2 km. The temperature at which seismic failure ceases for the strain rates likely at the Hengill geothermal area is determined by analogy with oceanic crust, and is about 650 ± 50 °C. The topographies of the top and bottom of the seismogenic layer were mapped using 617 earthquakes located highly accurately by performing a simultaneous inversion for three-dimensional structure and hypocentral parameters. The thickness of the seismogenic layer is roughly constant and about 3 km. A shallow, aseismic, low-velocity volume within the spreading plate boundary that crosses the area occurs above the top of the seismogenic layer and is interpreted as an isolated body of partial melt. The base of the seismogenic layer has a maximum depth of about 6.5 km beneath the spreading axis and deepens to about 7 km beneath a transform zone in the south of the area. Beneath the high-temperature part of the geothermal area, the maximum depth of earthquakes may be as shallow as 4 km. The geothermal gradient below drilling depths in various parts of the area ranges from 84 ± 9 °Ckm -1 within the low-temperature geothermal area of the transform zone to 138 ± 15 °Ckm -1 below the centre of the high-temperature geothermal area. Shallow maximum depths of earthquakes and therefore high average geothermal gradients tend to correlate with the intensity of the geothermal area and not with the location of the currently active spreading axis.

Propagation of hydro-meteorological uncertainty in a model cascade framework to inundation prediction

Science.gov (United States)

Rodríguez-Rincón, J. P.; Pedrozo-Acuña, A.; Breña-Naranjo, J. A.

2015-07-01

This investigation aims to study the propagation of meteorological uncertainty within a cascade modelling approach to flood prediction. The methodology was comprised of a numerical weather prediction (NWP) model, a distributed rainfall-runoff model and a 2-D hydrodynamic model. The uncertainty evaluation was carried out at the meteorological and hydrological levels of the model chain, which enabled the investigation of how errors that originated in the rainfall prediction interact at a catchment level and propagate to an estimated inundation area and depth. For this, a hindcast scenario is utilised removing non-behavioural ensemble members at each stage, based on the fit with observed data. At the hydrodynamic level, an uncertainty assessment was not incorporated; instead, the model was setup following guidelines for the best possible representation of the case study. The selected extreme event corresponds to a flood that took place in the southeast of Mexico during November 2009, for which field data (e.g. rain gauges; discharge) and satellite imagery were available. Uncertainty in the meteorological model was estimated by means of a multi-physics ensemble technique, which is designed to represent errors from our limited knowledge of the processes generating precipitation. In the hydrological model, a multi-response validation was implemented through the definition of six sets of plausible parameters from past flood events. Precipitation fields from the meteorological model were employed as input in a distributed hydrological model, and resulting flood hydrographs were used as forcing conditions in the 2-D hydrodynamic model. The evolution of skill within the model cascade shows a complex aggregation of errors between models, suggesting that in valley-filling events hydro-meteorological uncertainty has a larger effect on inundation depths than that observed in estimated flood inundation extents.

Tsunami-hazard assessment based on subaquatic slope-failure susceptibility and tsunami-inundation modeling

Science.gov (United States)

Anselmetti, Flavio; Hilbe, Michael; Strupler, Michael; Baumgartner, Christoph; Bolz, Markus; Braschler, Urs; Eberli, Josef; Liniger, Markus; Scheiwiller, Peter; Strasser, Michael

2015-04-01

Due to their smaller dimensions and confined bathymetry, lakes act as model oceans that may be used as analogues for the much larger oceans and their margins. Numerous studies in the perialpine lakes of Central Europe have shown that their shores were repeatedly struck by several-meters-high tsunami waves, which were caused by subaquatic slides usually triggered by earthquake shaking. A profound knowledge of these hazards, their intensities and recurrence rates is needed in order to perform thorough tsunami-hazard assessment for the usually densely populated lake shores. In this context, we present results of a study combining i) basinwide slope-stability analysis of subaquatic sediment-charged slopes with ii) identification of scenarios for subaquatic slides triggered by seismic shaking, iii) forward modeling of resulting tsunami waves and iv) mapping of intensity of onshore inundation in populated areas. Sedimentological, stratigraphical and geotechnical knowledge of the potentially unstable sediment drape on the slopes is required for slope-stability assessment. Together with critical ground accelerations calculated from already failed slopes and paleoseismic recurrence rates, scenarios for subaquatic sediment slides are established. Following a previously used approach, the slides are modeled as a Bingham plastic on a 2D grid. The effect on the water column and wave propagation are simulated using the shallow-water equations (GeoClaw code), which also provide data for tsunami inundation, including flow depth, flow velocity and momentum as key variables. Combining these parameters leads to so called «intensity maps» for flooding that provide a link to the established hazard mapping framework, which so far does not include these phenomena. The current versions of these maps consider a 'worst case' deterministic earthquake scenario, however, similar maps can be calculated using probabilistic earthquake recurrence rates, which are expressed in variable amounts of

Flood-inundation maps for Grand River, Red Cedar River, and Sycamore Creek near Lansing, Michigan

Science.gov (United States)

Whitehead, Matthew; Ostheimer, Chad J.

2015-08-26

Digital flood-inundation maps for a total of 19.7 miles of the Grand River, the Red Cedar River, and Sycamore Creek were created by the U.S. Geological Survey (USGS) in cooperation with the City of Lansing, Michigan, and the U.S. Army Corps of Engineers. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, show estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at three USGS streamgages: Grand River at Lansing, MI (04113000), Red Cedar River at East Lansing, MI (04112500), and Sycamore Creek at Holt Road near Holt, MI (04112850). Near-real-time stages at these streamgages can be obtained on the Internet from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at http:/water.weather.gov/ahps/, which also forecasts flood hydrographs at all of these sites.

Flood-inundation maps for Peachtree Creek from the Norfolk Southern Railway bridge to the Moores Mill Road NW bridge, Atlanta, Georgia

Science.gov (United States)

Musser, Jonathan W.

2012-01-01

Digital flood-inundation maps for a 5.5-mile reach of the Peachtree Creek from the Norfolk Southern Railway bridge to the Moores Mill Road NW bridge, were developed by the U.S. Geological Survey (USGS) in cooperation with the City of Atlanta, Georgia. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at Peachtree Creek at Atlanta, Georgia (02336300) and the USGS streamgage at Chattahoochee River at Georgia 280, near Atlanta, Georgia (02336490). Current water level (stage) at these USGS streamgages may be obtained at http://waterdata.usgs.gov/ and can be used in conjunction with these maps to estimate near real-time areas of inundation. The National Weather Service (NWS) is incorporating results from this study into the Advanced Hydrologic Prediction Service (AHPS) flood warning system (http:/water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that commonly are collocated at USGS streamgages. The forecasted peak-stage information for the USGS streamgage at Peachtree Creek, which is available through the AHPS Web site, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. A one-dimensional step-backwater model was developed using the U.S. Army Corps of Engineers HEC–RAS software for a 6.5-mile reach of Peachtree Creek and was used to compute flood profiles for a 5.5-mile reach of the creek. The model was calibrated using the most current stage-discharge relations at the Peachtree Creek at Atlanta, Georgia, streamgage (02336300), and the Chattahoochee River at Georgia 280, near Atlanta, Georgia, streamgage (02336490) as well as high water marks collected during the 2010 annual peak flow event. The hydraulic model was then used to determine 50 water

Flood-inundation maps for the Saluda River from Old Easley Bridge Road to Saluda Lake Dam near Greenville, South Carolina

Science.gov (United States)

Benedict, Stephen T.; Caldwell, Andral W.; Clark, Jimmy M.

2013-01-01

Digital flood-inundation maps for a 3.95-mile reach of the Saluda River from approximately 815 feet downstream from Old Easley Bridge Road to approximately 150 feet downstream from Saluda Lake Dam near Greenville, South Carolina, were developed by the U.S. Geological Survey (USGS). The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at Saluda River near Greenville, South Carolina (station 02162500). Current conditions at the USGS streamgage may be obtained through the National Water Information System Web site at http://waterdata.usgs.gov/sc/nwis/uv/?site_no=02162500&PARAmeter_cd=00065,00060,00062. The National Weather Service (NWS) forecasts flood hydrographs at many places that are often collocated with USGS streamgages. Forecasted peak-stage information is available on the Internet at the NWS Advanced Hydrologic Prediction Service (AHPS) flood-warning system Web site (http://water.weather.gov/ahps/) and may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation.In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated using the most current stage-streamflow relations at USGS streamgage station 02162500, Saluda River near Greenville, South Carolina. The hydraulic model was then used to determine water-surface profiles for flood stages at 1.0-foot intervals referenced to the streamgage datum and ranging from approximately bankfull to 2 feet higher than the highest recorded water level at the streamgage. The simulated water-surface profiles were then exported to a geographic information system, ArcGIS, and combined with a digital elevation model (derived from Light Detection and Ranging [LiDAR] data with a 0

Modeling and simulation of storm surge on Staten Island to understand inundation mitigation strategies

Science.gov (United States)

Kress, Michael E.; Benimoff, Alan I.; Fritz, William J.; Thatcher, Cindy A.; Blanton, Brian O.; Dzedzits, Eugene

2016-01-01

Hurricane Sandy made landfall on October 29, 2012, near Brigantine, New Jersey, and had a transformative impact on Staten Island and the New York Metropolitan area. Of the 43 New York City fatalities, 23 occurred on Staten Island. The borough, with a population of approximately 500,000, experienced some of the most devastating impacts of the storm. Since Hurricane Sandy, protective dunes have been constructed on the southeast shore of Staten Island. ADCIRC+SWAN model simulations run on The City University of New York's Cray XE6M, housed at the College of Staten Island, using updated topographic data show that the coast of Staten Island is still susceptible to tidal surge similar to those generated by Hurricane Sandy. Sandy hindcast simulations of storm surges focusing on Staten Island are in good agreement with observed storm tide measurements. Model results calculated from fine-scaled and coarse-scaled computational grids demonstrate that finer grids better resolve small differences in the topography of critical hydraulic control structures, which affect storm surge inundation levels. The storm surge simulations, based on post-storm topography obtained from high-resolution lidar, provide much-needed information to understand Staten Island's changing vulnerability to storm surge inundation. The results of fine-scale storm surge simulations can be used to inform efforts to improve resiliency to future storms. For example, protective barriers contain planned gaps in the dunes to provide for beach access that may inadvertently increase the vulnerability of the area.

Inundation, sedimentation, and subsidence creates goose habitat along the Arctic coast of Alaska

International Nuclear Information System (INIS)

Tape, Ken D; Flint, Paul L; Meixell, Brandt W; Gaglioti, Benjamin V

2013-01-01

The Arctic Coastal Plain of Alaska is characterized by thermokarst lakes and drained lake basins, and the rate of coastal erosion has increased during the last half-century. Portions of the coast are <1 m above sea level for kilometers inland, and are underlain by ice-rich permafrost. Increased storm surges or terrestrial subsidence would therefore expand the area subject to marine inundation. Since 1976, the distribution of molting Black Brant (Branta bernicla nigricans) on the Arctic Coastal Plain has shifted from inland freshwater lakes to coastal marshes, such as those occupying the Smith River and Garry Creek estuaries. We hypothesized that the movement of geese from inland lakes was caused by an expansion of high quality goose forage in coastal areas. We examined the recent history of vegetation and geomorphological changes in coastal goose habitat by combining analysis of time series imagery between 1948 and 2010 with soil stratigraphy dated using bomb-curve radiocarbon. Time series of vertical imagery and in situ verification showed permafrost thaw and subsidence of polygonal tundra. Soil stratigraphy and dating within coastal estuaries showed that non-saline vegetation communities were buried by multiple sedimentation episodes between 1948 and 1995, accompanying a shift toward salt-tolerant vegetation. This sedimentation allowed high quality goose forage plants to expand, thus facilitating the shift in goose distribution. Declining sea ice and the increasing rate of terrestrial inundation, sedimentation, and subsidence in coastal estuaries of Alaska may portend a ‘tipping point’ whereby inland areas would be transformed into salt marshes. (letter)

Prediction of phosphorus mobilisation in inundated floodplain soils

Energy Technology Data Exchange (ETDEWEB)

Loeb, Roos [Department of Aquatic Ecology and Environmental Biology, Institute for Water and Wetland Research, Radboud University Nijmegen, Toernooiveld 1, 6525 ED Nijmegen (Netherlands)], E-mail: r.loeb@science.ru.nl; Lamers, Leon P.M.; Roelofs, Jan G.M. [Department of Aquatic Ecology and Environmental Biology, Institute for Water and Wetland Research, Radboud University Nijmegen, Toernooiveld 1, 6525 ED Nijmegen (Netherlands)

2008-11-15

After flooding, iron reduction in riverine wetlands may cause the release of large quantities of phosphorus. As phosphorus is an important nutrient causing eutrophication in aquatic systems, it is important to have a tool to predict this potential release. In this study we examined the P release to the soil pore water in soil cores from floodplains in the Netherlands and from less anthropogenically influenced floodplains from Poland. During the inundation experiment, concentrations of P in the pore water rose to 2-90 times the initial concentrations. P release was not directly related to the geographic origin of the soils. An important predictor variable of P release was found in the ratio between the concentration of iron-bound P and amorphous iron. This ratio may provide a practical tool for the selection of new areas for wetland creation, and for impact assessment of plans for riverine wetland restoration and floodwater storage. - Mobilisation of phosphorus in floodplain wetland soils can be predicted with easily measurable soil characteristics.

Prediction of phosphorus mobilisation in inundated floodplain soils

International Nuclear Information System (INIS)

Loeb, Roos; Lamers, Leon P.M.; Roelofs, Jan G.M.

2008-01-01

After flooding, iron reduction in riverine wetlands may cause the release of large quantities of phosphorus. As phosphorus is an important nutrient causing eutrophication in aquatic systems, it is important to have a tool to predict this potential release. In this study we examined the P release to the soil pore water in soil cores from floodplains in the Netherlands and from less anthropogenically influenced floodplains from Poland. During the inundation experiment, concentrations of P in the pore water rose to 2-90 times the initial concentrations. P release was not directly related to the geographic origin of the soils. An important predictor variable of P release was found in the ratio between the concentration of iron-bound P and amorphous iron. This ratio may provide a practical tool for the selection of new areas for wetland creation, and for impact assessment of plans for riverine wetland restoration and floodwater storage. - Mobilisation of phosphorus in floodplain wetland soils can be predicted with easily measurable soil characteristics

GIS-BASED PREDICTION OF HURRICANE FLOOD INUNDATION

Energy Technology Data Exchange (ETDEWEB)

JUDI, DAVID [Los Alamos National Laboratory; KALYANAPU, ALFRED [Los Alamos National Laboratory; MCPHERSON, TIMOTHY [Los Alamos National Laboratory; BERSCHEID, ALAN [Los Alamos National Laboratory

2007-01-17

A simulation environment is being developed for the prediction and analysis of the inundation consequences for infrastructure systems from extreme flood events. This decision support architecture includes a GIS-based environment for model input development, simulation integration tools for meteorological, hydrologic, and infrastructure system models and damage assessment tools for infrastructure systems. The GIS-based environment processes digital elevation models (30-m from the USGS), land use/cover (30-m NLCD), stream networks from the National Hydrography Dataset (NHD) and soils data from the NRCS (STATSGO) to create stream network, subbasins, and cross-section shapefiles for drainage basins selected for analysis. Rainfall predictions are made by a numerical weather model and ingested in gridded format into the simulation environment. Runoff hydrographs are estimated using Green-Ampt infiltration excess runoff prediction and a 1D diffusive wave overland flow routing approach. The hydrographs are fed into the stream network and integrated in a dynamic wave routing module using the EPA's Storm Water Management Model (SWMM) to predict flood depth. The flood depths are then transformed into inundation maps and exported for damage assessment. Hydrologic/hydraulic results are presented for Tropical Storm Allison.

Tsunami inundation variability from stochastic rupture scenarios: Application to multiple inversions of the 2011 Tohoku, Japan earthquake

KAUST Repository

Mori, Nobuhito; Mai, Paul Martin; Goda, Katsuichiro; Yasuda, Tomohiro

2017-01-01

earthquake in the Tohoku region to conduct thorough sensitivity analyses and to quantify the inundation variability. The numerical results indicate a strong influence of the reference source models on inundation variability, and demonstrate significant

Flood-inundation maps for Sweetwater Creek from above the confluence of Powder Springs Creek to the Interstate 20 bridge, Cobb and Douglas Counties, Georgia

Science.gov (United States)

Musser, Jonathan W.

2012-01-01

Digital flood-inundation maps for a 10.5-mile reach of Sweetwater Creek, from about 1,800 feet above the confluence of Powder Springs Creek to about 160 feet below the Interstate 20 bridge, were developed by the U.S. Geological Survey (USGS) in cooperation with Cobb County, Georgia. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at Sweetwater Creek near Austell, Georgia (02337000). Current stage at this USGS streamgage may be obtained at http://waterdata.usgs.gov/ and can be used in conjunction with these maps to estimate near real-time areas of inundation. The National Weather Service (NWS) is incorporating results from this study into the Advanced Hydrologic Prediction Service (AHPS) flood-warning system (http://water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that commonly are collocated at USGS streamgages. The forecasted peak-stage information for the USGS streamgage at Sweetwater Creek near Austell (02337000), which is available through the AHPS Web site, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. A one-dimensional step-backwater model was developed using the U.S. Army Corps of Engineers Hydrologic Engineering Centers River Analysis System (HEC–RAS) software for Sweetwater Creek and was used to compute flood profiles for a 10.5-mile reach of the creek. The model was calibrated using the most current stage-discharge relations at the Sweetwater Creek near Austell streamgage (02337000), as well as high-water marks collected during annual peak-flow events in 1982 and 2009. The hydraulic model was then used to determine 21 water-surface profiles for flood stages at the Sweetwater Creek streamgage at 1-foot intervals referenced to the

Influence of urban pattern on inundation flow in floodplains of lowland rivers.

Science.gov (United States)

Bruwier, M; Mustafa, A; Aliaga, D G; Archambeau, P; Erpicum, S; Nishida, G; Zhang, X; Pirotton, M; Teller, J; Dewals, B

2018-05-01

The objective of this paper is to investigate the respective influence of various urban pattern characteristics on inundation flow. A set of 2000 synthetic urban patterns were generated using an urban procedural model providing locations and shapes of streets and buildings over a square domain of 1×1km 2 . Steady two-dimensional hydraulic computations were performed over the 2000 urban patterns with identical hydraulic boundary conditions. To run such a large amount of simulations, the computational efficiency of the hydraulic model was improved by using an anisotropic porosity model. This model computes on relatively coarse computational cells, but preserves information from the detailed topographic data through porosity parameters. Relationships between urban characteristics and the computed inundation water depths have been based on multiple linear regressions. Finally, a simple mechanistic model based on two district-scale porosity parameters, combining several urban characteristics, is shown to capture satisfactorily the influence of urban characteristics on inundation water depths. The findings of this study give guidelines for more flood-resilient urban planning. Copyright © 2017 Elsevier B.V. All rights reserved.

Flood-inundation maps for a 12.5-mile reach of Big Papillion Creek at Omaha, Nebraska

Science.gov (United States)

Strauch, Kellan R.; Dietsch, Benjamin J.; Anderson, Kayla J.

2016-03-22

Digital flood-inundation maps for a 12.5-mile reach of the Big Papillion Creek from 0.6 mile upstream from the State Street Bridge to the 72nd Street Bridge in Omaha, Nebraska, were created by the U.S. Geological Survey (USGS) in cooperation with the Papio-Missouri River Natural Resources District. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage on the Big Papillion Creek at Fort Street at Omaha, Nebraska (station 06610732). Near-real-time stages at this streamgage may be obtained on the Internet from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service Advanced Hydrologic Prediction Service at http:/water.weather.gov/ahps/, which also forecasts flood hydrographs at this site.

Flood occurrence mapping of the middle Mahakam lowland area using satellite radar

Directory of Open Access Journals (Sweden)

H. Hidayat

2012-07-01

Full Text Available Floodplain lakes and peatlands in the middle Mahakam lowland area are considered as ecologically important wetland in East Kalimantan, Indonesia. However, due to a lack of data, the hydrological functioning of the region is still poorly understood. Among remote sensing techniques that can increase data availability, radar is well-suitable for the identification, mapping, and measurement of tropical wetlands, for its cloud unimpeded sensing and night and day operation. Here we aim to extract flood extent and flood occurrence information from a series of radar images of the middle Mahakam lowland area. We explore the use of Phased Array L-band Synthetic Aperture Radar (PALSAR imagery for observing flood inundation dynamics by incorporating field water level measurements. Water level measurements were carried out along the river, in lakes and in peatlands, using pressure transducers. For validation of the open water flood occurrence map, bathymetry measurements were carried out in the main lakes. A series of PALSAR images covering the middle and lower Mahakam area in the years 2007 through 2010 were collected. A fully inundated region can be easily recognized on radar images from a dark signature. Open water flood occurrence was mapped using a threshold value taken from radar backscatter of the permanently inundated river and lakes areas. Radar backscatter intensity analysis of the vegetated floodplain area revealed consistently high backscatter values, indicating flood inundation under forest canopy. We used those values as the threshold for flood occurrence mapping in the vegetated area.

Implications of Inundation by the 2011 Tohoku-oki Tsunami for Coastal Agriculture on the Sendai Plain

Science.gov (United States)

Chague-Goff, C.; Goff, J. R.; Wong, H. K.; Sugawara, D.; SzczuciEski, W.

2013-05-01

The 11 March 2011 Tohoku-oki tsunami inundated large areas of farmland on the Sendai Plain, leaving behind a discontinuous, but extensive, sandy to muddy deposit coating paddy rice fields. Two months after the tsunami, many areas were still inundated on the low-lying plain. Salt crusts were also observed in many places where saltwater had evaporated. Field surveys were carried out in May, August, October 2011 and February 2012 along a ~ 5 km transect north of Sendai airport, to assess the environmental impact and temporal extent of the tsunami on farmland, with particular emphasis on contamination by salts. Evaporation led to elevated conductivity in ponded water, canals and channels in May 2011 (from brackish to saline), and while rainfall resulted in dilution, brackish water was still recorded in August and October 2011, and even in a few areas in February 2012. Our study revealed that not only the sediment deposited by the tsunami (sand-dominated up to 2.9 km inland, and mud-dominated up to 4.65 km inland) but also the underlying soil was contaminated by saltwater. Concentrations of up to 10.5% Cl, 6.6% Na, 2.8% SO4 and 440 mg kg-1 Br were recorded in May 2011 in surface sediment where seawater had ponded for a long time, as shown by extensive salt crust residues. The underlying rice paddy soil was also contaminated by saltwater, down to 15 cm depth, as revealed by high levels of water-leachable ions and cations. Data gathered over four sampling seasons 2, 5, 9 and 11 months after the tsunami show that the salt content generally decreased with time. Ion concentrations were however higher in February 2012 than in October 2011, probably due to evaporation following long periods with low precipitation. In February 2012, the area with chloride concentrations likely to result in brine damage in rice seedlings still extended from ~2.3 to ~3.3 km inland, with soil contamination by salt measured down to 15 cm depth in some places. Rice production was halted in 2011, and

Qu'Appelle River Dam, dam break analysis using advanced GIS tools for rapid modelling and inundation mapping

Energy Technology Data Exchange (ETDEWEB)

Bonin, D. [Hatch Energy, Winnipeg, MB (Canada); Campbell, C. [Saskatchewan Watershed Authority, Moose Jaw, SK (Canada); Groeneveld, J. [Hatch Energy, Calgary, AB (Canada)

2008-07-01

The South Saskatchewan River Project (SSRP) comprises a multi-purpose reservoir that provides water for conservation and irrigation, flood control, power generation, recreation, and municipal and industrial water supply. In addition to the 64 m high Gardiner Dam, the 27 m high Qu'Appelle River Dam and the 22 km long Lake Diefenbaker Reservoir, the SSRP also includes ancillary works. The Qu'Appelle River valley extends for 458 km before connecting to the Assiniboine River. The valley is incised up to 90 m in depth and is a popular cottaging and recreational area with several major communities located in the flood plain. In the event of a breach of the Qu'Appelle Dam, the discharge will increase from a normal maximum discharge of under 60 m{sup 3} per second to over 50,000 m{sup 3} per second. The Saskatchewan Watershed Authority (SWA) is responsible for ensuring safe development of the Province's water resources, without affecting reservoir or lake operations, and preventing damage from flooding, erosion or land slides. It is in the process of developing Hazard Assessments and emergency preparedness plans for each of their dams in accordance with the Canadian Dam Safety Guidelines. Studies using GIS technology and the hydrodynamic routing model HEC-RAS have been completed to evaluate the potential inundation that may result in the event of failure of the Qu'Appelle River Dam. These studies involved the development of a breach parameter model using a breach data set revised to better reflect the Qu'Appelle River Dam; the development of a dam break model for the Qu'Appelle River Dam and downstream river and flood plain; and, the use of this model to simulate two potential dam failure scenarios for the Qu'Appelle River Dam, notably failure during passage of the PMF and failure during fair weather conditions. Inundation maps have been prepared for the downstream Qu'Appelle River valley for each of the above events. 3 refs., 4

Projected inundations on the South African coast by tsunami waves

African Journals Online (AJOL)

Hayley.Cawthra

wind waves and swells, and because of its relatively short period, .... Inundation modelling attempts to recreate the tsunami generation in deep or ... The preservation of tsunami deposits in the coastal geological record is a function of the.

Tsunami inundation variability from stochastic rupture scenarios: Application to multiple inversions of the 2011 Tohoku, Japan earthquake

KAUST Repository

Mori, Nobuhito

2017-06-28

We develop a framework for assessing the sensitivity and variability of tsunami inundation characteristics for stochastic physics-based scenarios of mega-thrust subduction earthquakes. The method is applied to the 2011 Tohoku, Japan earthquake, and tested against observed inundation maps at several locations along the Tohoku coast, using 11 different, previously published, rupture models for this devastating tsunamgenic earthquake. The earthquake rupture models differ in fault dimension (length and width), geometry (dip, strike and top-edge depth), as well as asperity characteristics (slip heterogeneity on the fault plane). The resulting source variability allows exploring a wide range of tsunami scenarios for an Mw9 mega-thrust subduction earthquake in the Tohoku region to conduct thorough sensitivity analyses and to quantify the inundation variability. The numerical results indicate a strong influence of the reference source models on inundation variability, and demonstrate significant sensitivity of inundation to the details of the rupture realization. Therefore, relying on a single particular earthquake rupture model as a representative case when varying earthquake source characteristics may lead to under-representation of the variability of potential scenarios. Moreover, the proposed framework facilitates the rigorous development of critical scenarios for tsunami hazard and risk assessments, which are particularly useful for tsunami hazard mapping and disaster preparedness planning.

Flood-inundation maps for Indian Creek and Tomahawk Creek, Johnson County, Kansas, 2014

Science.gov (United States)

Peters, Arin J.; Studley, Seth E.

2016-01-25

Digital flood-inundation maps for a 6.4-mile upper reach of Indian Creek from College Boulevard to the confluence with Tomahawk Creek, a 3.9-mile reach of Tomahawk Creek from 127th Street to the confluence with Indian Creek, and a 1.9-mile lower reach of Indian Creek from the confluence with Tomahawk Creek to just beyond the Kansas/Missouri border at State Line Road in Johnson County, Kansas, were created by the U.S. Geological Survey in cooperation with the city of Overland Park, Kansas. The flood-inundation maps, which can be accessed through the U.S. Geological Survey Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the U.S. Geological Survey streamgages on Indian Creek at Overland Park, Kansas; Indian Creek at State Line Road, Leawood, Kansas; and Tomahawk Creek near Overland Park, Kansas. Near real time stages at these streamgages may be obtained on the Web from the U.S. Geological Survey National Water Information System at http://waterdata.usgs.gov/nwis or the National Weather Service Advanced Hydrologic Prediction Service at http://water.weather.gov/ahps/, which also forecasts flood hydrographs at these sites.Flood profiles were computed for the stream reaches by means of a one-dimensional step-backwater model. The model was calibrated for each reach by using the most current stage-discharge relations at the streamgages. The hydraulic models were then used to determine 15 water-surface profiles for Indian Creek at Overland Park, Kansas; 17 water-surface profiles for Indian Creek at State Line Road, Leawood, Kansas; and 14 water-surface profiles for Tomahawk Creek near Overland Park, Kansas, for flood stages at 1-foot intervals referenced to the streamgage datum and ranging from bankfull to the next interval above the 0.2-percent annual exceedance probability flood level (500-year recurrence interval). The

Nevada Test Site flood inundation study: Part of US Geological Survey flood potential and debris hazard study, Yucca Mountain Site for USDOE, Office of Civilian Radioactive Waste Management

International Nuclear Information System (INIS)

Blanton, J.O. III.

1992-01-01

The Geological Survey (GS), as part of the Yucca Mountain Project (YMP), is conducting studies at Yucca Mountain, Nevada. The purposes of these studies are to provide hydrologic and geologic information to evaluate the suitability of Yucca Mountain for development as a high-level nuclear waste repository, and to evaluate the ability of the mined geologic disposal system (MGDS) to isolate the waste in compliance with regulatory requirements. The Bureau of Reclamation was selected by the GS as a contractor to provide probable maximum flood (PMF) magnitudes and associated inundation maps for preliminary engineering design of the surface facilities at Yucca Mountain. These PMF peak flow estimates and associated inundation maps are necessary for successful waste repository design and construction. The standard step method for backwater computations, incorporating the Bernouli energy equation and the results of the PMF study were chosen as the basis for defining the areal extent of flooding

Flood Inundation Modelling Under Uncertainty Using Globally and Freely Available Remote Sensing Data

Science.gov (United States)

Yan, K.; Di Baldassarre, G.; Giustarini, L.; Solomatine, D. P.

2012-04-01

The extreme consequences of recent catastrophic events have highlighted that flood risk prevention still needs to be improved to reduce human losses and economic damages, which have considerably increased worldwide in recent years. Flood risk management and long term floodplain planning are vital for living with floods, which is the currently proposed approach to cope with floods. To support the decision making processes, a significant issue is the availability of data to build appropriate and reliable models, from which the needed information could be obtained. The desirable data for model building, calibration and validation are often not sufficient or available. A unique opportunity is offered nowadays by globally available data which can be freely downloaded from internet. This might open new opportunities for filling the gap between available and needed data, in order to build reliable models and potentially lead to the development of global inundation models to produce floodplain maps for the entire globe. However, there remains the question of what is the real potential of those global remote sensing data, characterized by different accuracy, for global inundation monitoring and how to integrate them with inundation models. This research aims at contributing to understand whether the current globally and freely available remote sensing data (e.g. SRTM, SAR) can be actually used to appropriately support inundation modelling. In this study, the SRTM DEM is used for hydraulic model building, while ENVISAT-ASAR satellite imagery is used for model validation. To test the usefulness of these globally and freely available data, a model based on the high resolution LiDAR DEM and ground data (high water marks) is used as benchmark. The work is carried out on a data-rich test site: the River Alzette in the north of Luxembourg City. Uncertainties are estimated for both SRTM and LiDAR based models. Probabilistic flood inundation maps are produced under the framework of

Flood-inundation maps for Lake Champlain in Vermont and in northern Clinton County, New York

Science.gov (United States)

Flynn, Robert H.; Hayes, Laura

2016-06-30

extents against the inundation area extents determined for the May 2011 flood (which incorporated documented high-water marksfrom the flood of May 201) (Bjerklie and others, 2014).A digital elevation model (DEM) was created by USGS, within a geographic information system (GIS), from the recently flown and processed light detection and ranging(lidar) data (2013–2014) in Vermont and the lake shore area of northern Clinton County in New York. The lidar data have a vertical accuracy of 0.3 to 0.6-ft (9.6 to 18.0-centimeters [cm]) and a horizontal resolution of 2.3 to 4.6 ft (0.7 to 1.4 meters). This DEM was used in determining the floodboundary for 11 flood stages at 0.5-ft intervals from 100.0 to104.0 ft (NGVD 29) and 1-ft intervals from 104.0 to 106.0 ft (NGVD 29) as referenced to the USGS lake gage 04295000, Richelieu River (Lake Champlain) at Rouses Point, N.Y. In addition, the May 2011 flood-inundation area for elevation103.20 ft (NGVD 29) (102.77 ft, North American Vertical Datum [NAVD] 88) was determined from this DEM. The May 2011 flood is the highest recorded lake water level (stage)at the Rouses Point, N.Y., lake gage. Flood stages greater than 101.5 ft (NGVD 29) exceed the “major flood stage”as defined by the NationalWeather Service for USGS lake gage 04295000.The availability of these maps, along with Internet information regarding current stage from the USGS lake gage and forecasted high-flow stages from the NationalWeather Service, will provide emergency management personnel and residents with information that is critical for flood responseactivities such as evacuations and road closures, as well as for post-flood recovery eforts.

Pressure transmission area and maximum pressure transmission of different thermoplastic resin denture base materials under impact load.

Science.gov (United States)

Nasution, Hubban; Kamonkhantikul, Krid; Arksornnukit, Mansuang; Takahashi, Hidekazu

2018-01-01

The purposes of the present study were to examine the pressure transmission area and maximum pressure transmission of thermoplastic resin denture base materials under an impact load, and to evaluate the modulus of elasticity and nanohardness of thermoplastic resin denture base. Three injection-molded thermoplastic resin denture base materials [polycarbonate (Basis PC), ethylene propylene (Duraflex), and polyamide (Valplast)] and one conventional heat-polymerized acrylic resin (PMMA, SR Triplex Hot) denture base, all with a mandibular first molar acrylic resin denture tooth set in were evaluated (n=6). Pressure transmission area and maximum pressure transmission of the specimens under an impact load were observed by using pressure-sensitive sheets. The modulus of elasticity and nanohardness of each denture base (n=10) were measured on 15×15×15×3mm 3 specimen by using an ultramicroindentation system. The pressure transmission area, modulus of elasticity, and nanohardness data were statistically analyzed with 1-way ANOVA, followed by Tamhane or Tukey HSD post hoc test (α=.05). The maximum pressure transmission data were statistically analyzed with Kruskal-Wallis H test, followed by Mann-Whitney U test (α=.05). Polymethyl methacrylate showed significantly larger pressure transmission area and higher maximum pressure transmission than the other groups (Pelasticity and nanohardness among the four types of denture bases (Pelasticity and nanohardness of each type of denture base were demonstrated. Copyright © 2017 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Analysis of flood inundation in ungauged basins based on multi-source remote sensing data.

Science.gov (United States)

Gao, Wei; Shen, Qiu; Zhou, Yuehua; Li, Xin

2018-02-09

Floods are among the most expensive natural hazards experienced in many places of the world and can result in heavy losses of life and economic damages. The objective of this study is to analyze flood inundation in ungauged basins by performing near-real-time detection with flood extent and depth based on multi-source remote sensing data. Via spatial distribution analysis of flood extent and depth in a time series, the inundation condition and the characteristics of flood disaster can be reflected. The results show that the multi-source remote sensing data can make up the lack of hydrological data in ungauged basins, which is helpful to reconstruct hydrological sequence; the combination of MODIS (moderate-resolution imaging spectroradiometer) surface reflectance productions and the DFO (Dartmouth Flood Observatory) flood database can achieve the macro-dynamic monitoring of the flood inundation in ungauged basins, and then the differential technique of high-resolution optical and microwave images before and after floods can be used to calculate flood extent to reflect spatial changes of inundation; the monitoring algorithm for the flood depth combining RS and GIS is simple and easy and can quickly calculate the depth with a known flood extent that is obtained from remote sensing images in ungauged basins. Relevant results can provide effective help for the disaster relief work performed by government departments.

The Hengill geothermal area, Iceland: variation of temperature gradients deduced from the maximum depth of seismogenesis

Science.gov (United States)

Foulger, G.R.

1995-01-01

Given a uniform lithology and strain rate and a full seismic data set, the maximum depth of earthquakes may be viewed to a first order as an isotherm. These conditions are approached at the Hengill geothermal area, S. Iceland, a dominantly basaltic area. The temperature at which seismic failure ceases for the strain rates likely at the Hengill geothermal area is determined by analogy with oceanic crust, and is about 650 ?? 50??C. The topographies of the top and bottom of the seismogenic layer were mapped using 617 earthquakes. The thickness of the seismogenic layer is roughly constant and about 3 km. A shallow, aseismic, low-velocity volume within the spreading plate boundary that crosses the area occurs above the top of the seismogenic layer and is interpreted as an isolated body of partial melt. The base of the seismogenic layer has a maximum depth of about 6.5 km beneath the spreading axis and deepens to about 7 km beneath a transform zone in the south of the area. -from Author

Parallel simulation of tsunami inundation on a large-scale supercomputer

Science.gov (United States)

Oishi, Y.; Imamura, F.; Sugawara, D.

2013-12-01

An accurate prediction of tsunami inundation is important for disaster mitigation purposes. One approach is to approximate the tsunami wave source through an instant inversion analysis using real-time observation data (e.g., Tsushima et al., 2009) and then use the resulting wave source data in an instant tsunami inundation simulation. However, a bottleneck of this approach is the large computational cost of the non-linear inundation simulation and the computational power of recent massively parallel supercomputers is helpful to enable faster than real-time execution of a tsunami inundation simulation. Parallel computers have become approximately 1000 times faster in 10 years (www.top500.org), and so it is expected that very fast parallel computers will be more and more prevalent in the near future. Therefore, it is important to investigate how to efficiently conduct a tsunami simulation on parallel computers. In this study, we are targeting very fast tsunami inundation simulations on the K computer, currently the fastest Japanese supercomputer, which has a theoretical peak performance of 11.2 PFLOPS. One computing node of the K computer consists of 1 CPU with 8 cores that share memory, and the nodes are connected through a high-performance torus-mesh network. The K computer is designed for distributed-memory parallel computation, so we have developed a parallel tsunami model. Our model is based on TUNAMI-N2 model of Tohoku University, which is based on a leap-frog finite difference method. A grid nesting scheme is employed to apply high-resolution grids only at the coastal regions. To balance the computation load of each CPU in the parallelization, CPUs are first allocated to each nested layer in proportion to the number of grid points of the nested layer. Using CPUs allocated to each layer, 1-D domain decomposition is performed on each layer. In the parallel computation, three types of communication are necessary: (1) communication to adjacent neighbours for the

Pengaruh Land Subsidence terhadap Genangan Banjir dan Rob di Semarang Timur

Directory of Open Access Journals (Sweden)

ratih Pujiastuti

2016-06-01

Full Text Available Inundation of flood and rob (flood due to high tides in Semarang City is increase wtithin area and depth. It be more seroius condition because of land subsisdence that happened in coastal area of Semarang City. This research is foccused on prediction and mapping of inundation flood and rob due to land subsidence effect in East Semarang, especially Tenggang Watershed and Sringin Watershed. On this research, data analysis including analysis of land subsidence, analysis of hydrological data, analysis of flood discharge with HEC-HMS, hydraulics analysis with HEC-RAS and then mapping the results of the flood inundation with Arc GIS. The inundation will be create with overlay the DEM of flood water level and DEM of topographic. According to the results of analysis is known that minimum land subsidence is 0 cm/year that happened in south area of Semarang and more higher ini north area with maximum land subsidence is 5.58 cm/year. On periode   2014-2031, the contribute of land subsidence to increase the inundation of flood and rob is 1.39%/year.

Assessment of trends in inundation extent in the Barotse Floodplain, upper Zambezi River Basin: A remote sensing-based approach

Directory of Open Access Journals (Sweden)

Henry Zimba

2018-02-01

New hydrological insights for the region: The results revealed that there is observable inter-annual variability in inundation extent in the Barotse Floodplain with prominent differences demonstrated in both the flood ascending/peak and receding period. For the period 2003–2013 the results indicated a rising trend in inundation extent with a Mann–Kendall Z statistic of 1.71 and increase in magnitude of 33.1 km2 at significance level alpha of 0.05. Strong correlations between inundation extent and water level and between inundation extent and discharge with correlation coefficients of determination of 0.86 and 0.89 respectively were observed. For the period 2000–2011 water level time series showed a rising trend with the Mann–Kendall Z statistic of 2.97 and increase in magnitude of 0.1 m at significance level alpha of 0.05. Overall, during the period 1952–2004 discharge in the floodplain showed a declining trend with Mann–Kendall Z statistics of −2.88 and −3.38 at the inlet and outlet of the floodplain respectively. By correlation inference, the overall inundation extent trend in the floodplain was in a downward movement. Rainfall and discharge variability, high evapotranspiration and the changes in the land cover-use in the catchment of the floodplain are largely the factors affecting the observed variability and trends in inundation extent in the floodplain. The presented remote sensing based approach significantly reduces the need for the expensive and time limiting traditional physical field based wetland inundation mapping methods that form a limitation for achieving progress in wetland monitoring especially in open and sparsely gauged floodplains such as the Barotse.

Run-up and inundation limits along southeast coast of India during the 26 December 2004 Indian Ocean tsunami

Digital Repository Service at National Institute of Oceanography (India)

Jayakumar, S.; Ilangovan, D.; Naik, K.A .; Gowthaman, R.; Tirodkar, G.; Naik, G.N.; Ganesan, P.; ManiMurali, R.; Michael, G.S.; Raman, M.V.; Bhattacharya, G.C.

protected by coastal dunes, had higher inundation values compared to places where the coast is protected by dunes. Also, wherever there are openings in the du nes (either due to anthropogenic acti v ity or due to other reasons), inund a tion...

Varying Inundation Regimes Differentially Affect Natural and Sand-Amended Marsh Sediments.

Directory of Open Access Journals (Sweden)

C Wigand

Full Text Available Climate change is altering sea level rise rates and precipitation patterns worldwide. Coastal wetlands are vulnerable to these changes. System responses to stressors are important for resource managers and environmental stewards to understand in order to best manage them. Thin layer sand or sediment application to drowning and eroding marshes is one approach to build elevation and resilience. The above- and below-ground structure, soil carbon dioxide emissions, and pore water constituents in vegetated natural marsh sediments and sand-amended sediments were examined at varying inundation regimes between mean sea level and mean high water (0.82 m NAVD88 to 1.49 m NAVD88 in a field experiment at Laws Point, part of the Plum Island Sound Estuary (MA. Significantly lower salinities, pH, sulfides, phosphates, and ammonium were measured in the sand-amended sediments than in the natural sediments. In natural sediments there was a pattern of increasing salinity with increasing elevation while in the sand-amended sediments the trend was reversed, showing decreasing salinity with increasing elevation. Sulfide concentrations generally increased from low to high inundation with highest concentrations at the highest inundation (i.e., at the lowest elevations. High pore water phosphate concentrations were measured at low elevations in the natural sediments, but the sand-amended treatments had mostly low concentrations of phosphate and no consistent pattern with elevation. At the end of the experiment the lowest elevations generally had the highest measures of pore water ammonium. Soil carbon dioxide emissions were greatest in the sand-amended mesocosms and at higher elevations. Differences in coarse root and rhizome abundances and volumes among the sediment treatments were detected with CT imaging, but by 20 weeks the natural and sand-amended treatments showed similar total belowground biomass at the intermediate and high elevations. Although differences in

Maximum skin dose assessment in interventional cardiology: large area detectors and calculation methods

International Nuclear Information System (INIS)

Quail, E.; Petersol, A.

2002-01-01

Advances in imaging technology have facilitated the development of increasingly complex radiological procedures for interventional radiology. Such interventional procedures can involve significant patient exposure, although often represent alternatives to more hazardous surgery or are the sole method for treatment. Interventional radiology is already an established part of mainstream medicine and is likely to expand further with the continuing development and adoption of new procedures. Between all medical exposures, interventional radiology is first of the list of the more expansive radiological practice in terms of effective dose per examination with a mean value of 20 mSv. Currently interventional radiology contribute 4% to the annual collective dose, in spite of contributing to total annual frequency only 0.3% but considering the perspectives of this method can be expected a large expansion of this value. In IR procedures the potential for deterministic effects on the skin is a risk to be taken into account together with stochastic long term risk. Indeed, the International Commission on Radiological Protection (ICRP) in its publication No 85, affirms that the patient dose of priority concern is the absorbed dose in the area of skin that receives the maximum dose during an interventional procedure. For the mentioned reasons, in IR it is important to give to practitioners information on the dose received by the skin of the patient during the procedure. In this paper maximum local skin dose (MSD) is called the absorbed dose in the area of skin receiving the maximum dose during an interventional procedure

Assessing the Influences of a Flood Diversion Project on Mitigating River Stage, Inundation Extent and Economic Loss

Directory of Open Access Journals (Sweden)

Wei-Bo Chen

2015-04-01

Full Text Available Taiwan usually suffers severe inundation disasters during typhoons and strong rainstorms, and therefore flood mitigation is considered an important issue. To assess the effect of the Yuansantze flood diversion tunnel (YFDT on flood mitigation at the upstream reaches of the Keelung River, a three-dimensional, unstructured grid, Finite-Volume, primitive equation Community Ocean Model (FVCOM was used. The model was validated with observed data for water levels and inundation extent during different typhoon events. The simulated results show a good agreement with field measurements of water level with three historical typhoon events but underestimated the measured inundation extent with Typhoon Nari. The validated model was then applied to assess the flood mitigation and economic loss with the YFDT. The results demonstrated that the river level decreases approximately 3 m with the YFDT and that the inundation extent decreases by more than 50% in the Ruifang District with YFDT. The YDFT aims to not only mitigate hazards but also reduce economic losses. The average annual expected benefit after construction of the YFDT is approximately 184 million NTD in the Ruifang District.

Identification of Storm Surge Vulnerable Areas in the Philippines Through Simulations of Typhoon Haiyan-Induced Storm Surge Using Tracks of Historical Tropical Cyclones

Science.gov (United States)

Lapidez, John Phillip; Suarez, John Kenneth; Tablazon, Judd; Dasallas, Lea; Gonzalo, Lia Anne; Santiago, Joy; Cabacaba, Krichi May; Ramos, Michael Marie Angelo; Mahar Francisco Lagmay, Alfredo; Malano, Vicente

2014-05-01

Super Typhoon Haiyan entered the Philippine Area of Responsibility (PAR) 07 November 2013, causing tremendous damage to infrastructure and loss of lives mainly due to the typhoon's storm surge and strong winds. Storm surges up to a height of 7 meters were reported in the hardest hit areas. The threat imposed by this kind of natural calamity compelled researchers of the Nationwide Operational Assessment of Hazards, the flagship disaster mitigation program of the Department of Science and Technology, Government of the Philippines, to undertake a study to determine the vulnerability of all Philippine coastal communities to storm surges of the same magnitude as those generated by Haiyan. This study calculates the maximum probable storm surge height for every coastal locality by running simulations of Haiyan-type conditions but with tracks of tropical cyclones that entered PAR from 1948-2013. DOST-Project NOAH used the Japan Meteorological Agency (JMA) Storm Surge Model, a numerical code that simulates and predicts storm surges spawned by tropical cyclones. Input parameters for the storm surge model include bathymetric data, storm track, central atmospheric pressure, and maximum wind speed. The simulations were made using Haiyan's pressure and wind speed as the forcing parameters. The simulated storm surge height values were added to the maximum tide level obtained from WXTide, software that contains a catalogue of worldwide astronomical tides, to come up with storm tide levels. The resulting water level was used as input to FLO-2D to generate the storm tide inundation maps. One product of this study is a list of the most vulnerable coastal areas that can be used as basis for choosing priority sites for further studies to implement appropriate site-specific solutions. Another product is the storm tide inundation maps that the local government units can use to develop a Risk-Sensitive Land Use Plan for identifying appropriate areas to build residential buildings

Niagara pumping generation station inundation mapping and consequence analysis with ArcGIS and Mike 21

Energy Technology Data Exchange (ETDEWEB)

Grover, Patrick; Khayer, Yasmin; Naumov, Aleksey [4DM Inc., Toronto, (Canada); Zhang, Yibing [Ontario Power Generation, Toronto, (Canada)

2010-07-01

Inundation mapping is a key factor of Ontario Power Generation's dam safety program. It is the basis for determining the hazard potential classification of the dam by modelling the consequences of a hypothetical dam failure. This paper presented the project for updating the inundation mapping and consequence analysis study at the Niagara Pump generating station (PGS) reservoir. A complete hydrotechnical assessment of the Niagara PGS reservoir was conducted. The modelling of various breach scenarios was carried out using the 2-D hydrodynamic software MIKE 21 in order to provide the hydraulic data necessary for producing the inundation maps. Updated EPRP maps were produced and a consequence analysis was performed which confirmed the existing hazard classification. The ArcGIS system was used as the underlying framework for all major components of the project. It was found that the use of GIS technologies improve the efficiency of both modelling and analysis.

Integration of coastal inundation modeling from storm tides to individual waves

Science.gov (United States)

Li, Ning; Roeber, Volker; Yamazaki, Yoshiki; Heitmann, Troy W.; Bai, Yefei; Cheung, Kwok Fai

2014-11-01

Modeling of storm-induced coastal inundation has primarily focused on the surge generated by atmospheric pressure and surface winds with phase-averaged effects of the waves as setup. Through an interoperable model package, we investigate the role of phase-resolving wave processes in simulation of coastal flood hazards. A spectral ocean wave model describes generation and propagation of storm waves from deep to intermediate water, while a non-hydrostatic storm-tide model has the option to couple with a spectral coastal wave model for computation of phase-averaged processes in a near-shore region. The ocean wave and storm-tide models can alternatively provide the wave spectrum and the surface elevation as the boundary and initial conditions for a nested Boussinesq model. Additional surface-gradient terms in the Boussinesq equations maintain the quasi-steady, non-uniform storm tide for modeling of phase-resolving surf and swash-zone processes as well as combined tide, surge, and wave inundation. The two nesting schemes are demonstrated through a case study of Hurricane Iniki, which made landfall on the Hawaiian Island of Kauai in 1992. With input from a parametric hurricane model and global reanalysis and tidal datasets, the two approaches produce comparable significant wave heights and phase-averaged surface elevations in the surf zone. The nesting of the Boussinesq model provides a seamless approach to augment the inundation due to the individual waves in matching the recorded debris line along the coast.

ESTIMATION OF DAMAGED AREAS DUE TO THE 2010 CHILE EARTHQUAKE AND TSUNAMI USING SAR IMAGERY OF ALOS/PALSAR

Directory of Open Access Journals (Sweden)

P. J. Ni Made

2016-06-01

Full Text Available A large-scale earthquake and tsunami affect thousands of people and cause serious damages worldwide every year. Quick observation of the disaster damage is extremely important for planning effective rescue operations. In the past, acquiring damage information was limited to only field surveys or using aerial photographs. In the last decade, space-borne images were used in many disaster researches, such as tsunami damage detection. In this study, SAR data of ALOS/PALSAR satellite images were used to estimate tsunami damage in the form of inundation areas in Talcahuano, the area near the epicentre of the 2010 Chile earthquake. The image processing consisted of three stages, i.e. pre-processing, analysis processing, and post-processing. It was conducted using multi-temporal images before and after the disaster. In the analysis processing, inundation areas were extracted through the masking processing. It consisted of water masking using a high-resolution optical image of ALOS/AVNIR-2 and elevation masking which built upon the inundation height using DEM image of ASTER-GDEM. The area result was 8.77 Km2. It showed a good result and corresponded to the inundation map of Talcahuano. Future study in another area is needed in order to strengthen the estimation processing method.

Dam break analysis and flood inundation map of Krisak dam for emergency action plan

Science.gov (United States)

Juliastuti, Setyandito, Oki

2017-11-01

The Indonesian Regulation which refers to the ICOLD Regulation (International Committee on Large Dam required have the Emergency Action Plan (EAP) guidelines because of the dams have potential failure. In EAP guidelines there is a management of evacuation where the determination of the inundation map based on flood modeling. The purpose of the EAP is to minimize the risk of loss of life and property in downstream which caused by dam failure. This paper will describe about develop flood modeling and inundation map in Krisak dam using numerical methods through dam break analysis (DBA) using hydraulic model Zhong Xing HY-21. The approaches of dam failure simulation are overtopping and piping. Overtopping simulation based on quadrangular, triangular and trapezium fracture. Piping simulation based on cracks of orifice. Using results of DBA, hazard classification of Krisak dam is very high. The nearest village affected dam failure is Singodutan village (distance is 1.45 kilometer from dam) with inundation depth is 1.85 meter. This result can be used by stakeholders such as emergency responders and the community at risk in formulating evacuation procedure.

Impact of a 1755-like tsunami in Huelva, Spain

Directory of Open Access Journals (Sweden)

V. V. Lima

2010-01-01

Full Text Available Coastal areas are highly exposed to natural hazards associated with the sea. In all cases where there is historical evidence for devastating tsunamis, as is the case of the southern coasts of the Iberian Peninsula, there is a need for quantitative hazard tsunami assessment to support spatial planning. Also, local authorities must be able to act towards the population protection in a preemptive way, to inform "what to do" and "where to go" and in an alarm, to make people aware of the incoming danger. With this in mind, we investigated the inundation extent, run-up and water depths, of a 1755-like event on the region of Huelva, located on the Spanish southwestern coast, one of the regions that was affected in the past by several high energy events, as proved by historical documents and sedimentological data. Modelling was made with a slightly modified version of the COMCOT (Cornell Multi-grid Coupled Tsunami Model code. Sensitivity tests were performed for a single source in order to understand the relevance and influence of the source parameters in the inundation extent and the fundamental impact parameters. We show that a 1755-like event will have a dramatic impact in a large area close to Huelva inundating an area between 82 and 92 km² and reaching maximum run-up around 5 m. In this sense our results show that small variations on the characteristics of the tsunami source are not too significant for the impact assessment. We show that the maximum flow depth and the maximum run-up increase with the average slip on the source, while the strike of the fault is not a critical factor as Huelva is significantly far away from the potential sources identified up to now. We also show that the maximum flow depth within the inundated area is very dependent on the tidal level, while maximum run-up is less affected, as a consequence of the complex morphology of the area.

Community disruptions and business costs for distant tsunami evacuations using maximum versus scenario-based zones

Science.gov (United States)

Wood, Nathan J.; Wilson, Rick I.; Ratliff, Jamie L.; Peters, Jeff; MacMullan, Ed; Krebs, Tessa; Shoaf, Kimberley; Miller, Kevin

2017-01-01

Well-executed evacuations are key to minimizing loss of life from tsunamis, yet they also disrupt communities and business productivity in the process. Most coastal communities implement evacuations based on a previously delineated maximum-inundation zone that integrates zones from multiple tsunami sources. To support consistent evacuation planning that protects lives but attempts to minimize community disruptions, we explore the implications of scenario-based evacuation procedures and use the California (USA) coastline as our case study. We focus on the land in coastal communities that is in maximum-evacuation zones, but is not expected to be flooded by a tsunami generated by a Chilean earthquake scenario. Results suggest that a scenario-based evacuation could greatly reduce the number of residents and employees that would be advised to evacuate for 24–36 h (178,646 and 159,271 fewer individuals, respectively) and these reductions are concentrated primarily in three counties for this scenario. Private evacuation spending is estimated to be greater than public expenditures for operating shelters in the area of potential over-evacuations ($13 million compared to $1 million for a 1.5-day evacuation). Short-term disruption costs for businesses in the area of potential over-evacuation are approximately $122 million for a 1.5-day evacuation, with one-third of this cost associated with manufacturing, suggesting that some disruption costs may be recouped over time with increased short-term production. There are many businesses and organizations in this area that contain individuals with limited mobility or access and functional needs that may have substantial evacuation challenges. This study demonstrates and discusses the difficulties of tsunami-evacuation decision-making for relatively small to moderate events faced by emergency managers, not only in California but in coastal communities throughout the world.

A framework for probabilistic pluvial flood nowcasting for urban areas

Science.gov (United States)

Ntegeka, Victor; Murla, Damian; Wang, Lipen; Foresti, Loris; Reyniers, Maarten; Delobbe, Laurent; Van Herk, Kristine; Van Ootegem, Luc; Willems, Patrick

2016-04-01

Pluvial flood nowcasting is gaining ground not least because of the advancements in rainfall forecasting schemes. Short-term forecasts and applications have benefited from the availability of such forecasts with high resolution in space (~1km) and time (~5min). In this regard, it is vital to evaluate the potential of nowcasting products for urban inundation applications. One of the most advanced Quantitative Precipitation Forecasting (QPF) techniques is the Short-Term Ensemble Prediction System, which was originally co-developed by the UK Met Office and Australian Bureau of Meteorology. The scheme was further tuned to better estimate extreme and moderate events for the Belgian area (STEPS-BE). Against this backdrop, a probabilistic framework has been developed that consists of: (1) rainfall nowcasts; (2) sewer hydraulic model; (3) flood damage estimation; and (4) urban inundation risk mapping. STEPS-BE forecasts are provided at high resolution (1km/5min) with 20 ensemble members with a lead time of up to 2 hours using a 4 C-band radar composite as input. Forecasts' verification was performed over the cities of Leuven and Ghent and biases were found to be small. The hydraulic model consists of the 1D sewer network and an innovative 'nested' 2D surface model to model 2D urban surface inundations at high resolution. The surface components are categorized into three groups and each group is modelled using triangular meshes at different resolutions; these include streets (3.75 - 15 m2), high flood hazard areas (12.5 - 50 m2) and low flood hazard areas (75 - 300 m2). Functions describing urban flood damage and social consequences were empirically derived based on questionnaires to people in the region that were recently affected by sewer floods. Probabilistic urban flood risk maps were prepared based on spatial interpolation techniques of flood inundation. The method has been implemented and tested for the villages Oostakker and Sint-Amandsberg, which are part of the

Enhanced Effects of Flood Disasters Due to Hillside Development in Urban Areas

Directory of Open Access Journals (Sweden)

Wei-Hsien Teng

2013-02-01

Full Text Available In recent years, the Taiwan government has established a number of flood control facilities such as dikes, pumping stations and drainage systems to effectively reduce downstream flooding. However, with continued development and urbanization of catchment areas, the original designs of most flood control facilities have become outdated. Hillside lands in the upper and middle reaches of river basins have undergone urban development through unsound engineering practices, paving the way for heavy downstream flooding. Therefore, proper river basin management should include both upstream and downstream sides. The main purpose of the paper is to simulate non-urban inundation areas with various degrees of development (0%, 10%, 20%, 40% and 60%, over two different return periods of 25 years and 200 years, for intensive rainfall events in the Shi-Chi District, Taiwan. Through hydrological analysis and numerical simulations of inundation, quantitative data on inundation potential have been established based on the land development conditions along the hillsides on the upper and middle reaches of the Keelung River Basin. The simulated results show that the increase in the extent of land development in the upper reaches causes an increase in the area and depth of inundation, resulting in an increased risk of flooding in downstream areas. If the land-use policy makers in the upper reaches of the river basin’s hillsides do not properly manage the land development, the risk of flooding in downstream areas will increase. In such an event, the policy makers should first review the situation to understand the problem with the consideration of this study. Thus, proper development and flood mitigation in hillsides can be established.

Coastal flood inundation monitoring with Satellite C-band and L-band Synthetic Aperture Radar data

Science.gov (United States)

Ramsey, Elijah W.; Rangoonwala, Amina; Bannister, Terri

2013-01-01

Satellite Synthetic Aperture Radar (SAR) was evaluated as a method to operationally monitor the occurrence and distribution of storm- and tidal-related flooding of spatially extensive coastal marshes within the north-central Gulf of Mexico. Maps representing the occurrence of marsh surface inundation were created from available Advanced Land Observation Satellite (ALOS) Phased Array type L-Band SAR (PALSAR) (L-band) (21 scenes with HH polarizations in Wide Beam [100 m]) data and Environmental Satellite (ENVISAT) Advanced SAR (ASAR) (C-band) data (24 scenes with VV and HH polarizations in Wide Swath [150 m]) during 2006-2009 covering 500 km of the Louisiana coastal zone. Mapping was primarily based on a decrease in backscatter between reference and target scenes, and as an extension of previous studies, the flood inundation mapping performance was assessed by the degree of correspondence between inundation mapping and inland water levels. Both PALSAR- and ASAR-based mapping at times were based on suboptimal reference scenes; however, ASAR performance seemed more sensitive to reference-scene quality and other types of scene variability. Related to water depth, PALSAR and ASAR mapping accuracies tended to be lower when water depths were shallow and increased as water levels decreased below or increased above the ground surface, but this pattern was more pronounced with ASAR. Overall, PALSAR-based inundation accuracies averaged 84% (n = 160), while ASAR-based mapping accuracies averaged 62% (n = 245).

Estrategias de intervención en áreas urbanas inundables: el caso Bella Unión, Uruguay

Directory of Open Access Journals (Sweden)

Adriana Piperno

2013-01-01

Full Text Available El objetivo de este trabajo es caracterizar y dar elementos para la acción en las áreas inundables de la ciudad de Bella Unión. Si bien las inundaciones no generan una situación de desastre, afectan fuertemente la economía local, impactando sobre sectores muy vulnerables de la población. El área inundable se ha visto incrementada a partir de 1979 por la puesta en funcionamiento de la represa de Salto Grande. Las acciones de indemnización se presentan como una oportunidad para realizar estudios pormenorizados de la zona y definir acciones convergentes e integrales para gestionar estas áreas. Se desarrolla una metodología basada en el análisis de la interacción del sistema hídrico con el sistema territorial, que permite reconocer los distintos niveles de riesgo de la zona afectada y los impactos asociados, considerando tanto el nivel de la amenaza como la vulnerabilidad de sus pobladores. El análisis incorpora igualmente las potencialidades de la zona, de forma de incorporar el río al imaginario colectivo de la ciudad.This study aims to characterize and provide items to operate in flooded areas of Bella Union city. Although floodings cannot be defined as disasters, they strongly affect the local economy, as they have an impact on vulnerable sectors of the population. Its floodplain has increased since 1979 by the installation of Salto Grande dam. Compensation actions arepresented as an opportunity for developing detailed studies of the area and definingfurther con vergent and integrated actions to manage these areas. The methodology is based on the analysis of the interaction of water and territorial systems, recognizing different levels of risk in the affected area and the associated impacts. It considers both the level of hazard and vulnerability of its inhabitants. It also recognizes the potential of the area to incorporate the river to the city's collective imaginary.

Assimilation of flood extent data with 2D flood inundation models for localised intense rainfall events

Science.gov (United States)

Neal, J. C.; Wood, M.; Bermúdez, M.; Hostache, R.; Freer, J. E.; Bates, P. D.; Coxon, G.

2017-12-01

Remote sensing of flood inundation extent has long been a potential source of data for constraining and correcting simulations of floodplain inundation. Hydrodynamic models and the computing resources to run them have developed to the extent that simulation of flood inundation in two-dimensional space is now feasible over large river basins in near real-time. However, despite substantial evidence that there is useful information content within inundation extent data, even from low resolution SAR such as that gathered by Envisat ASAR in wide swath mode, making use of the information in a data assimilation system has proved difficult. He we review recent applications of the Ensemble Kalman Filter (EnKF) and Particle Filter for assimilating SAR data, with a focus on the River Severn UK and compare these with complementary research that has looked at the internal error sources and boundary condition errors using detailed terrestrial data that is not available in most locations. Previous applications of the EnKF to this reach have focused on upstream boundary conditions as the source of flow error, however this description of errors was too simplistic for the simulation of summer flood events where localised intense rainfall can be substantial. Therefore, we evaluate the introduction of uncertain lateral inflows to the ensemble. A further limitation of the existing EnKF based methods is the need to convert flood extent to water surface elevations by intersecting the shoreline location with a high quality digital elevation model (e.g. LiDAR). To simplify this data processing step, we evaluate a method to directly assimilate inundation extent as a EnKF model state rather than assimilating water heights, potentially allowing the scheme to be used where high-quality terrain data are sparse.

Flood-inundation maps for the Withlacoochee River From Skipper Bridge Road to St. Augustine Road, within the City of Valdosta, Georgia, and Lowndes County, Georgia

Science.gov (United States)

Musser, Jonathan W.

2018-01-31

Digital flood-inundation maps for a 12.6-mile reach of the Withlacoochee River from Skipper Bridge Road to St. Augustine Road (Georgia State Route 133) were developed to depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the U.S. Geological Survey (USGS) streamgage at Withlacoochee River at Skipper Bridge Road, near Bemiss, Ga. (023177483). Real-time stage information from this streamgage can be used with these maps to estimate near real-time areas of inundation. The forecasted peak-stage information for the USGS streamgage at Withlacoochee River at Skipper Bridge Road, near Bemiss, Ga. (023177483), can be used in conjunction with the maps developed for this study to show predicted areas of flood inundation.A one-dimensional step-backwater model was developed using the U.S. Army Corps of Engineers Hydrologic Engineer-ing Center’s River Analysis System (HEC–RAS) software for the Withlacoochee River and was used to compute flood profiles for a 12.6-mile reach of the Withlacoochee River. The hydraulic model was then used to simulate 23 water-surface profiles at 1.0-foot (ft) intervals at the Withlacoochee River near the Bemiss streamgage. The profiles ranged from the National Weather Service action stage of 10.7 ft, which is 131.0 ft above the North American Vertical Datum of 1988 (NAVD 88), to a stage of 32.7 ft, which is 153.0 ft above NAVD 88. The simulated water-surface profiles were then combined with a geographic information system digital elevation model—derived from light detection and ranging (lidar) data having a 4.0-ft horizontal resolution—to delineate the area flooded at each 1.0-ft interval of stream stage.

A Tsunami Ball Approach to Storm Surge and Inundation: Application to Hurricane Katrina, 2005

Directory of Open Access Journals (Sweden)

Steven N. Ward

2009-01-01

Full Text Available Most analyses of storm surge and inundation solve equations of continuity and momentum on fixed finite-difference/finite-element meshes. I develop a completely new approach that uses a momentum equation to accelerate bits or balls of water over variable depth topography. The thickness of the water column at any point equals the volume density of balls there. In addition to being more intuitive than traditional methods, the tsunami ball approach has several advantages. (a By tracking water balls of fixed volume, the continuity equation is satisfied automatically and the advection term in the momentum equation becomes unnecessary. (b The procedure is meshless in the finite-difference/finite-element sense. (c Tsunami balls care little if they find themselves in the ocean or inundating land. (d Tsunami ball calculations of storm surge can be done on a laptop computer. I demonstrate and calibrate the method by simulating storm surge and inundation around New Orleans, Louisiana caused by Hurricane Katrina in 2005 and by comparing model predictions with field observations. To illustrate the flexibility of the tsunami ball technique, I run two “What If” hurricane scenarios—Katrina over Savannah, Georgia and Katrina over Cape Cod, Massachusetts.

Numerical Modeling of Coastal Inundation and Sedimentation by Storm Surge, Tides, and Waves at Norfolk, Virginia, USA

Science.gov (United States)

2012-07-01

hurricanes (tropical) with a 50-year and a 100-year return period, and one winter storm ( extratropical ) occurred in October 1982. There are a total of 15...under the 0-m and 2-m SLR scenarios, respectively. • Tropical and extratropical storms induce extensive coastal inundation around the military...1 NUMERICAL MODELING OF COASTAL INUNDATION AND SEDIMENTATION BY STORM SURGE, TIDES, AND WAVES AT NORFOLK, VIRGINIA, USA Honghai Li 1 , Lihwa Lin 1

Predicting the Extent of Inundation due to Sea-Level Rise: Al Hamra Development, Ras Al Khaimah, UAE. A Pilot Project

Directory of Open Access Journals (Sweden)

Arthur Robert M.

2016-06-01

Full Text Available As new information is received, predictions of sea-level rise resulting from global warming continue to be revised upwards. Measurements indicate that the rise in sea-level is continuing at, or close to, the worst case forecasts (Kellet et al. 2014. Coastal areas are coming under increasing risk of inundation and flooding as storms are predicted to increase in frequency and severity, adding to the risk of inundation due to higher sea levels. Stakeholders, government agencies, developers and land owners require accurate, up to date information to be able to protect coastal areas. Geographic Information Systems (GIS along with accurate remote sensing technologies such as LiDAR provides the best means for delivering this information. Using these technologies, this paper predicts the risk posed to a large multi-use development in the emirate of Ras Al Khaimah, UAE. This development, Al Hamra Village, is situated on the coast of the Arabian Gulf. Al Hamra’s physical relationship to the Gulf is in common with other developments in Ras Al Khaimah in its and for this reason has been used as a pilot project. The resulting GIS model shows that Al Hamra is indeed at risk from predicted flood events. How this information can be used as a planning tool for numerous strategies is discussed in this paper.

Automating Flood Hazard Mapping Methods for Near Real-time Storm Surge Inundation and Vulnerability Assessment

Science.gov (United States)

Weigel, A. M.; Griffin, R.; Gallagher, D.

2015-12-01

Storm surge has enough destructive power to damage buildings and infrastructure, erode beaches, and threaten human life across large geographic areas, hence posing the greatest threat of all the hurricane hazards. The United States Gulf of Mexico has proven vulnerable to hurricanes as it has been hit by some of the most destructive hurricanes on record. With projected rises in sea level and increases in hurricane activity, there is a need to better understand the associated risks for disaster mitigation, preparedness, and response. GIS has become a critical tool in enhancing disaster planning, risk assessment, and emergency response by communicating spatial information through a multi-layer approach. However, there is a need for a near real-time method of identifying areas with a high risk of being impacted by storm surge. Research was conducted alongside Baron, a private industry weather enterprise, to facilitate automated modeling and visualization of storm surge inundation and vulnerability on a near real-time basis. This research successfully automated current flood hazard mapping techniques using a GIS framework written in a Python programming environment, and displayed resulting data through an Application Program Interface (API). Data used for this methodology included high resolution topography, NOAA Probabilistic Surge model outputs parsed from Rich Site Summary (RSS) feeds, and the NOAA Census tract level Social Vulnerability Index (SoVI). The development process required extensive data processing and management to provide high resolution visualizations of potential flooding and population vulnerability in a timely manner. The accuracy of the developed methodology was assessed using Hurricane Isaac as a case study, which through a USGS and NOAA partnership, contained ample data for statistical analysis. This research successfully created a fully automated, near real-time method for mapping high resolution storm surge inundation and vulnerability for the

Modeled inundation limits of potential lahars from Mount Adams in the White Salmon River Valley, Washington

Science.gov (United States)

Griswold, Julia P.; Pierson, Thomas C.; Bard, Joseph A.

2018-05-09

inundation zones accompanying this report, shown in two different map perspectives, is intended to augment (not replace) the existing hazard maps for Mount Adams (W.E. Scott and others, 1995; Vallance, 1999). The maps in this report show potential areas of inundation by lahars of different initial volumes, which are determined by a computer model, LAHARZ (Iverson and others, 1998; Schilling, 1998). One map sheet presents LAHARZ-determined inundation areas on a normal plan-view shaded-relief map of the study area; the other gives an oblique perspective of the landscape with raised topography, as if one were viewing the landscape at an angle from an aircraft (Jenny and Patterson, 2007). LAHARZ was developed after the original hazard maps (based only on mapping of geologic deposits) were made. Predicted inundation zones on these maps provide an alternative approach to estimation of areas that could be inundated as lahars of different volumes pass through the valley. However, there is considerable uncertainty in the exact location of the hazard-zone boundaries shown on these maps, as well as on earlier maps.

Flood-inundation maps and wetland restoration suitability index for the Blue River and selected tributaries, Kansas City, Missouri, and vicinity, 2012

Science.gov (United States)

Heimann, David C.; Kelly, Brian P.; Studley, Seth E.

2015-01-01

Digital flood-inundation maps for a 39.7-mile reach of the Blue River and selected tributaries (Brush Creek, Indian Creek, and Dyke Branch) at Kansas City, Missouri, and vicinity, were created by the U.S. Geological Survey (USGS) in cooperation with the City of Kansas City, Missouri. The flood-inundation maps, accessed through the USGS Flood-Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the spatial extent and depth of flooding corresponding to selected water levels (stages) at 15 reference streamgages and associated stream reaches in the Blue River Basin. Near-real-time stage data from the streamgages may be obtained from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service (NWS) Advanced Hydrologic Prediction Service (AHPS) at http://water.weather.gov/ahps/, which also forecasts flood hydrographs at selected sites.

Analisis Genangan Banjir di Kawasan Sekitar Kolam Retensi dan Rencana Pengendaliannya, Studi Kasus: Kolam Retensi Siti Khadijah Palembang

Directory of Open Access Journals (Sweden)

M. Baitullah Al Amin

2016-08-01

Full Text Available The area near the Siti Khadijah Palembang retention pond, especially Demang Lebar Daun street, is frequently inundated because of the overflowing of the retention pond, causing long traffic jams. This study aims to analyze the characteristics of flood inundation within the area for the existing situation and for a scenario of flood control using a pump system and an increase in open space. The flood routing within the retention pond was done using HEC-HMS software, while visualization of flood inundation was carried out using Global Mapper software. The results show that the capacity of the retention pond at this time is insufficient to accommodate run-off volume, whereas the flood peak discharge of 22.2 m3/s for a 5-year return period has the potential to inundate 11.09 Ha of the surrounding area. Flood control using pumps with a total capacity of 4 m3/s is able to reduce the inundation extent by 58.79%, while a 30% increase in  open space is only able to reduce the inundation extent by 15.33%. Furthermore, a combination of flood pumps and an increase in open space can reduce the inundation extent by 75.92%. Using this method results in a maximum inundation depth of less than 0.5 m with a potential inundation time of only 20 minutes, where Demang Lebar Daun street is no longer inundated. For short-term flood mitigation, there is a need to build a flood pump station at the Siti Khadijah retention pond , while for long-term mitigation there is a need to gradually and sustainably provide open space.

Validation of a Global Hydrodynamic Flood Inundation Model

Science.gov (United States)

Bates, P. D.; Smith, A.; Sampson, C. C.; Alfieri, L.; Neal, J. C.

2014-12-01

In this work we present first validation results for a hyper-resolution global flood inundation model. We use a true hydrodynamic model (LISFLOOD-FP) to simulate flood inundation at 1km resolution globally and then use downscaling algorithms to determine flood extent and depth at 90m spatial resolution. Terrain data are taken from a custom version of the SRTM data set that has been processed specifically for hydrodynamic modelling. Return periods of flood flows along the entire global river network are determined using: (1) empirical relationships between catchment characteristics and index flood magnitude in different hydroclimatic zones derived from global runoff data; and (2) an index flood growth curve, also empirically derived. Bankful return period flow is then used to set channel width and depth, and flood defence impacts are modelled using empirical relationships between GDP, urbanization and defence standard of protection. The results of these simulations are global flood hazard maps for a number of different return period events from 1 in 5 to 1 in 1000 years. We compare these predictions to flood hazard maps developed by national government agencies in the UK and Germany using similar methods but employing detailed local data, and to observed flood extent at a number of sites including St. Louis, USA and Bangkok in Thailand. Results show that global flood hazard models can have considerable skill given careful treatment to overcome errors in the publicly available data that are used as their input.

Analysis of Compound Water Hazard in Coastal Urbanized Areas under the Future Climate

Science.gov (United States)

Shibuo, Y.; Taniguchi, K.; Sanuki, H.; Yoshimura, K.; Lee, S.; Tajima, Y.; Koike, T.; Furumai, H.; Sato, S.

2017-12-01

Several studies indicate the increased frequency and magnitude of heavy rainfalls as well as the sea level rise under the future climate, which implies that coastal low-lying urbanized areas may experience increased risk against flooding. In such areas, where river discharge, tidal fluctuation, and city drainage networks altogether influence urban inundation, it is necessary to consider their potential interference to understand the effect of compound water hazard. For instance, pump stations cannot pump out storm water when the river water level is high, and in the meantime the river water level shall increase when it receives pumped water from cities. At the further downstream, as the tidal fluctuation regulates the water levels in the river, it will also affect the functionality of pump stations and possible inundation from rivers. In this study, we estimate compound water hazard in the coastal low-lying urbanized areas of the Tsurumi river basin under the future climate. We developed the seamlessly integrated river, sewerage, and coastal hydraulic model that can simulate river water levels, water flow in sewerage network, and inundation from the rivers and/or the coast to address the potential interference issue. As a forcing, the pseudo global warming method, which applies the changes in GCM anomaly to re-analysis data, is employed to produce ensemble typhoons to drive the seamlessly integrated model. The results show that heavy rainfalls caused by the observed typhoon generally become stronger under the pseudo global climate condition. It also suggests that the coastal low-lying areas become extensively inundated if the onset of river flooding and storm surge coincides.

Flood pulsing in the Sudd wetland: analysis of seasonal variations in 2 inundation and evapotranspiration in Southern Sudan

Science.gov (United States)

Senay, Gabriel B.; Rebelo, L-M.; McCartney, M.P.

2012-01-01

Located on the Bahr el Jebel in South Sudan, the Sudd is one of the largest floodplain wetlands in the world. Seasonal inundation drives the hydrologic, geomorphological, and ecological processes, and the annual flood pulse is essential to the functioning of the Sudd. Despite the importance of the flood pulse, various hydrological interventions are planned upstream of the Sudd to increase economic benefits and food security. These will not be without consequences, in particular for wetlands where the biological productivity, biodiversity, and human livelihoods are dependent on the flood pulse and both the costs and benefits need to be carefully evaluated. Many African countries still lack regional baseline information on the temporal extent, distribution, and characteristics of wetlands, making it hard to assess the consequences of development interventions. Because of political instability in Sudan and the inaccessible nature of the Sudd, recent measurements of flooding and seasonal dynamics are inadequate. Analyses of multitemporal and multisensor remote sensing datasets are presented in this paper, in order to investigate and characterize flood pulsing within the Sudd wetland over a 12-month period. Wetland area has been mapped along with dominant components of open water and flooded vegetation at five time periods over a single year. The total area of flooding (both rain and river fed) over the 12 months was 41 334 km2, with 9176 km2 of this constituting the permanent wetland. Mean annual total evaporation is shown to be higher and with narrower distribution of values from areas of open water (1718 mm) than from flooded vegetation (1641 mm). Although the exact figures require validation against ground-based measurements, the results highlight the relative differences in inundation patterns and evaporation across the Sudd.

Syncrude`s highway berm: part 3 of 5 - Soil parameters (pore pressure parameters and settlement from inundation)

Energy Technology Data Exchange (ETDEWEB)

Cameron, R.; Fong, V.; Ashton, C.; Strueby, B. [Syncrude Canada Ltd., Edmonton, AB (Canada)

1995-12-31

Difficulties in predicting pore fluid pressures in the fills composing the highway berm were discussed. The pore water pressures in the in-situ clay foundation units were expected to be very sensitive to water content. Over 200 piezometer tips were installed into fill and in situ soil units, and results of the measurements were reported. The in situ basal foundation clays and sands were found to have a similar pore pressure ratio of typically less than 0.25. Fill pore fluid pressure ratios determined in the field varied according to density when loose fills were compared to very dense fills. To illustrate, when the fill was 86% to 91% of maximum Standard Proctor Density, the pore pressure ratio value was not dependent on fluid content. When the fill was densely compacted to 98% Standard Proctor Density, the pore pressure ratio was largely dependent on the fluid content as it related to the optimum fluid content determined from Standard Proctor testing. Significant first-time wetting settlement was observed to occur with fills at initial densities of around 90% of maximum Standard Proctor dry density. Settlements for fills placed initially above 97% Standard Proctor Density generally had inundation settlements of less than 0.3% of fill thickness predicted from laboratory testing. 4 refs., 10 figs., 1 tab.

Flood-inundation maps for the Meramec River at Valley Park and at Fenton, Missouri, 2017

Science.gov (United States)

Dietsch, Benjamin J.; Sappington, Jacob N.

2017-09-29

Two sets of digital flood-inundation map libraries that spanned a combined 16.7-mile reach of the Meramec River that extends upstream from Valley Park, Missouri, to downstream from Fenton, Mo., were created by the U.S. Geological Survey (USGS) in cooperation with the U.S. Army Corps of Engineers, St. Louis Metropolitan Sewer District, Missouri Department of Transportation, Missouri American Water, and Federal Emergency Management Agency Region 7. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science website at https://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the cooperative USGS streamgages on the Meramec River at Valley Park, Mo., (USGS station number 07019130) and the Meramec River at Fenton, Mo. (USGS station number 07019210). Near-real-time stage data at these streamgages may be obtained from the USGS National Water Information System at https://waterdata.usgs.gov/nwis or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at http:/water.weather.gov/ahps/, which also forecasts flood hydrographs at these sites (listed as NWS sites vllm7 and fnnm7, respectively).Flood profiles were computed for the stream reaches by means of a calibrated one-dimensional step-backwater hydraulic model. The model was calibrated using a stage-discharge relation at the Meramec River near Eureka streamgage (USGS station number 07019000) and documented high-water marks from the flood of December 2015 through January 2016.The calibrated hydraulic model was used to compute two sets of water-surface profiles: one set for the streamgage at Valley Park, Mo. (USGS station number 07019130), and one set for the USGS streamgage on the Meramec River at Fenton, Mo. (USGS station number 07019210). The water-surface profiles were produced for stages at 1-foot (ft) intervals referenced to the datum from each streamgage and

WRF-Chem simulations in the Amazon region during wet and dry season transitions: evaluation of methane models and wetland inundation maps

Science.gov (United States)

Beck, V.; Gerbig, C.; Koch, T.; Bela, M. M.; Longo, K. M.; Freitas, S. R.; Kaplan, J. O.; Prigent, C.; Bergamaschi, P.; Heimann, M.

2013-08-01

The Amazon region, being a large source of methane (CH4), contributes significantly to the global annual CH4 budget. For the first time, a forward and inverse modelling framework on regional scale for the purpose of assessing the CH4 budget of the Amazon region is implemented. Here, we present forward simulations of CH4 as part of the forward and inverse modelling framework based on a modified version of the Weather Research and Forecasting model with chemistry that allows for passive tracer transport of CH4, carbon monoxide, and carbon dioxide (WRF-GHG), in combination with two different process-based bottom-up models of CH4 emissions from anaerobic microbial production in wetlands and additional datasets prescribing CH4 emissions from other sources such as biomass burning, termites, or other anthropogenic emissions. We compare WRF-GHG simulations on 10 km horizontal resolution to flask and continuous CH4 observations obtained during two airborne measurement campaigns within the Balanço Atmosférico Regional de Carbono na Amazônia (BARCA) project in November 2008 and May 2009. In addition, three different wetland inundation maps, prescribing the fraction of inundated area per grid cell, are evaluated. Our results indicate that the wetland inundation maps based on remote-sensing data represent the observations best except for the northern part of the Amazon basin and the Manaus area. WRF-GHG was able to represent the observed CH4 mixing ratios best at days with less convective activity. After adjusting wetland emissions to match the averaged observed mixing ratios of flights with little convective activity, the monthly CH4 budget for the Amazon basin obtained from four different simulations ranges from 1.5 to 4.8 Tg for November 2008 and from 1.3 to 5.5 Tg for May 2009. This corresponds to an average CH4 flux of 9-31 mg m-2 d-1 for November 2008 and 8-36 mg m-2 d-1 for May 2009.

A simple procedure to model water level fluctuations in partially inundated wetlands

NARCIS (Netherlands)

Spieksma, JFM; Schouwenaars, JM

When modelling groundwater behaviour in wetlands, there are specific problems related to the presence of open water in small-sized mosaic patterns. A simple quasi two-dimensional model to predict water level fluctuations in partially inundated wetlands is presented. In this model, the ratio between

Subpixel Inundation Mapping Using Landsat-8 OLI and UAV Data for a Wetland Region on the Zoige Plateau, China

Directory of Open Access Journals (Sweden)

Haoming Xia

2017-01-01

Full Text Available Wetland inundation is crucial to the survival and prosperity of fauna and flora communities in wetland ecosystems. Even small changes in surface inundation may result in a substantial impact on the wetland ecosystem characteristics and function. This study presented a novel method for wetland inundation mapping at a subpixel scale in a typical wetland region on the Zoige Plateau, northeast Tibetan Plateau, China, by combining use of an unmanned aerial vehicle (UAV and Landsat-8 Operational Land Imager (OLI data. A reference subpixel inundation percentage (SIP map at a Landsat-8 OLI 30 m pixel scale was first generated using high resolution UAV data (0.16 m. The reference SIP map and Landsat-8 OLI imagery were then used to develop SIP estimation models using three different retrieval methods (Linear spectral unmixing (LSU, Artificial neural networks (ANN, and Regression tree (RT. Based on observations from 2014, the estimation results indicated that the estimation model developed with RT method could provide the best fitting results for the mapping wetland SIP (R2 = 0.933, RMSE = 8.73% compared to the other two methods. The proposed model with RT method was validated with observations from 2013, and the estimated SIP was highly correlated with the reference SIP, with an R2 of 0.986 and an RMSE of 9.84%. This study highlighted the value of high resolution UAV data and globally and freely available Landsat data in combination with the developed approach for monitoring finely gradual inundation change patterns in wetland ecosystems.

Lava inundation zone maps for Mauna Loa, Island of Hawaiʻi, Hawaii

Science.gov (United States)

Trusdell, Frank A.; Zoeller, Michael H.

2017-10-12

Lava flows from Mauna Loa volcano, on the Island of Hawaiʻi, constitute a significant hazard to people and property. This report addresses those lava flow hazards, mapping 18 potential lava inundation zones on the island.

Modeling surface water dynamics in the Amazon Basin using MOSART-Inundation v1.0: impacts of geomorphological parameters and river flow representation

Science.gov (United States)

Luo, Xiangyu; Li, Hong-Yi; Leung, L. Ruby; Tesfa, Teklu K.; Getirana, Augusto; Papa, Fabrice; Hess, Laura L.

2017-03-01

In the Amazon Basin, floodplain inundation is a key component of surface water dynamics and plays an important role in water, energy and carbon cycles. The Model for Scale Adaptive River Transport (MOSART) was extended with a macroscale inundation scheme for representing floodplain inundation. The extended model, named MOSART-Inundation, was used to simulate surface hydrology of the entire Amazon Basin. Previous hydrologic modeling studies in the Amazon Basin identified and addressed a few challenges in simulating surface hydrology of this basin, including uncertainties of floodplain topography and channel geometry, and the representation of river flow in reaches with mild slopes. This study further addressed four aspects of these challenges. First, the spatial variability of vegetation-caused biases embedded in the HydroSHEDS digital elevation model (DEM) data was explicitly addressed. A vegetation height map of about 1 km resolution and a land cover dataset of about 90 m resolution were used in a DEM correction procedure that resulted in an average elevation reduction of 13.2 m for the entire basin and led to evident changes in the floodplain topography. Second, basin-wide empirical formulae for channel cross-sectional dimensions were refined for various subregions to improve the representation of spatial variability in channel geometry. Third, the channel Manning roughness coefficient was allowed to vary with the channel depth, as the effect of riverbed resistance on river flow generally declines with increasing river size. Lastly, backwater effects were accounted for to better represent river flow in mild-slope reaches. The model was evaluated against in situ streamflow records and remotely sensed Envisat altimetry data and Global Inundation Extent from Multi-Satellites (GIEMS) inundation data. In a sensitivity study, seven simulations were compared to evaluate the impacts of the five modeling aspects addressed in this study. The comparisons showed that

Flood-Inundation maps for the Hohokus Brook in Waldwick Borough, Ho-Ho-Kus Borough, and the Village of Ridgewood, New Jersey, 2014

Science.gov (United States)

Watson, Kara M.; Niemoczynski, Michal J.

2015-07-20

Digital flood-inundation maps for a 6-mile reach of the Hohokus Brook in New Jersey from White's Lake Dam in Waldwick Borough, through Ho-Ho-Kus Borough to Grove Street in the Village of Ridgewood were created by the U.S. Geological Survey (USGS) in cooperation with the New Jersey Department of Environmental Protection. The flood inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage on the Hohokus Brook at Ho-Ho-Kus, New Jersey (station number 01391000). Stage data at this streamgage may be obtained on the Internet from the USGS National Water Information System at http://waterdata.usgs.gov/nwis/uv?site_no=01391000 or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at http://water.weather.gov/ahps2/hydrograph.php?gage=hohn4&wfo=okx.

Risk Analysis of Coastal hazard Considering Sea-level Rise and Local Environment in Coastal Area

Science.gov (United States)

Sangjin, P.; Lee, D. K.; KIM, H.; Ryu, J. E.; Yoo, S.; Ryoo, H.

2014-12-01

Recently, natural hazards has been more unpredictable with increasing frequency and strength due to climate change. Especially, coastal areas would be more vulnerable in the future because of sea-level rise (SLR). In case of Korea, it is surrounded by oceans and has many big cities at coastal area, thus a hazard prevention plan in coastal area is absolutely necessary. However, prior to making the plan, finding areas at risk would be the first step. In order to find the vulnerable area, local characteristics of coastal areas should also be considered along with SLR. Therefore, the objective of the research is to find vulnerable areas, which could be damaged by coastal hazards considering local environment and SLR of coastal areas. Spatial scope of the research was set up as 1km from the coastline according to the 'coastal management law' in Korea. The assessment was done up to the year of 2050, and the highest sea level rise scenario was used. For risk analysis, biophysical and socioeconomic characteristics were considered as to represent local characteristics of coastal area. Risk analysis was carried out through the combination of 'possibility of hazard' and the 'level of damages', and both of them reflect the above-mentioned regional characteristics. Since the range of inundation was narrowed down to the inundation from typhoon in this research, the possibility of inundation caused by typhoon was estimated by using numerical model, which calculated the height of storm surge considering wave, tide, sea-level pressure and SLR. Also the level of damage was estimated by categorizing the socioeconomic character into four factors; human, infrastructure, ecology and socioeconomic. Variables that represent each factor were selected and used in damage estimation with their classification and weighting value. The result shows that the urban coastal areas are more vulnerable and hazardous than other areas because of socioeconomic factors. The east and the south coast are

Comparison of new generation low-complexity flood inundation mapping tools with a hydrodynamic model

Science.gov (United States)

Afshari, Shahab; Tavakoly, Ahmad A.; Rajib, Mohammad Adnan; Zheng, Xing; Follum, Michael L.; Omranian, Ehsan; Fekete, Balázs M.

2018-01-01

The objective of this study is to compare two new generation low-complexity tools, AutoRoute and Height Above the Nearest Drainage (HAND), with a two-dimensional hydrodynamic model (Hydrologic Engineering Center-River Analysis System, HEC-RAS 2D). The assessment was conducted on two hydrologically different and geographically distant test-cases in the United States, including the 16,900 km2 Cedar River (CR) watershed in Iowa and a 62 km2 domain along the Black Warrior River (BWR) in Alabama. For BWR, twelve different configurations were set up for each of the models, including four different terrain setups (e.g. with and without channel bathymetry and a levee), and three flooding conditions representing moderate to extreme hazards at 10-, 100-, and 500-year return periods. For the CR watershed, models were compared with a simplistic terrain setup (without bathymetry and any form of hydraulic controls) and one flooding condition (100-year return period). Input streamflow forcing data representing these hypothetical events were constructed by applying a new fusion approach on National Water Model outputs. Simulated inundation extent and depth from AutoRoute, HAND, and HEC-RAS 2D were compared with one another and with the corresponding FEMA reference estimates. Irrespective of the configurations, the low-complexity models were able to produce inundation extents similar to HEC-RAS 2D, with AutoRoute showing slightly higher accuracy than the HAND model. Among four terrain setups, the one including both levee and channel bathymetry showed lowest fitness score on the spatial agreement of inundation extent, due to the weak physical representation of low-complexity models compared to a hydrodynamic model. For inundation depth, the low-complexity models showed an overestimating tendency, especially in the deeper segments of the channel. Based on such reasonably good prediction skills, low-complexity flood models can be considered as a suitable alternative for fast

Relationship between the Prediction Accuracy of Tsunami Inundation and Relative Distribution of Tsunami Source and Observation Arrays: A Case Study in Tokyo Bay

Science.gov (United States)

Takagawa, T.

2017-12-01

A rapid and precise tsunami forecast based on offshore monitoring is getting attention to reduce human losses due to devastating tsunami inundation. We developed a forecast method based on the combination of hierarchical Bayesian inversion with pre-computed database and rapid post-computing of tsunami inundation. The method was applied to Tokyo bay to evaluate the efficiency of observation arrays against three tsunamigenic earthquakes. One is a scenario earthquake at Nankai trough and the other two are historic ones of Genroku in 1703 and Enpo in 1677. In general, rich observation array near the tsunami source has an advantage in both accuracy and rapidness of tsunami forecast. To examine the effect of observation time length we used four types of data with the lengths of 5, 10, 20 and 45 minutes after the earthquake occurrences. Prediction accuracy of tsunami inundation was evaluated by the simulated tsunami inundation areas around Tokyo bay due to target earthquakes. The shortest time length of accurate prediction varied with target earthquakes. Here, accurate prediction means the simulated values fall within the 95% credible intervals of prediction. In Enpo earthquake case, 5-minutes observation is enough for accurate prediction for Tokyo bay, but 10-minutes and 45-minutes are needed in the case of Nankai trough and Genroku, respectively. The difference of the shortest time length for accurate prediction shows the strong relationship with the relative distance from the tsunami source and observation arrays. In the Enpo case, offshore tsunami observation points are densely distributed even in the source region. So, accurate prediction can be rapidly achieved within 5 minutes. This precise prediction is useful for early warnings. Even in the worst case of Genroku, where less observation points are available near the source, accurate prediction can be obtained within 45 minutes. This information can be useful to figure out the outline of the hazard in an early

Observed and forecast flood-inundation mapping application-A pilot study of an eleven-mile reach of the White River, Indianapolis, Indiana

Science.gov (United States)

Kim, Moon H.; Morlock, Scott E.; Arihood, Leslie D.; Kiesler, James L.

2011-01-01

Near-real-time and forecast flood-inundation mapping products resulted from a pilot study for an 11-mile reach of the White River in Indianapolis. The study was done by the U.S. Geological Survey (USGS), Indiana Silver Jackets hazard mitigation taskforce members, the National Weather Service (NWS), the Polis Center, and Indiana University, in cooperation with the City of Indianapolis, the Indianapolis Museum of Art, the Indiana Department of Homeland Security, and the Indiana Department of Natural Resources, Division of Water. The pilot project showed that it is technically feasible to create a flood-inundation map library by means of a two-dimensional hydraulic model, use a map from the library to quickly complete a moderately detailed local flood-loss estimate, and automatically run the hydraulic model during a flood event to provide the maps and flood-damage information through a Web graphical user interface. A library of static digital flood-inundation maps was created by means of a calibrated two-dimensional hydraulic model. Estimated water-surface elevations were developed for a range of river stages referenced to a USGS streamgage and NWS flood forecast point colocated within the study reach. These maps were made available through the Internet in several formats, including geographic information system, Keyhole Markup Language, and Portable Document Format. A flood-loss estimate was completed for part of the study reach by using one of the flood-inundation maps from the static library. The Federal Emergency Management Agency natural disaster-loss estimation program HAZUS-MH, in conjunction with local building information, was used to complete a level 2 analysis of flood-loss estimation. A Service-Oriented Architecture-based dynamic flood-inundation application was developed and was designed to start automatically during a flood, obtain near real-time and forecast data (from the colocated USGS streamgage and NWS flood forecast point within the study reach

The October 2015 flash-floods in south eastern France: hydrological analyses, inundation mapping and impact estimations

Science.gov (United States)

Payrastre, Olivier; Bourgin, François; Lebouc, Laurent; Le Bihan, Guillaume; Gaume, Eric

2017-04-01

The October 2015 flash-floods in south eastern France caused more than twenty fatalities, high damages and large economic losses in high density urban areas of the Mediterranean coast, including the cities of Mandelieu-La Napoule, Cannes and Antibes. Following a post event survey and preliminary analyses conducted within the framework of the Hymex project, we set up an entire simulation chain at the regional scale to better understand this outstanding event. Rainfall-runoff simulations, inundation mapping and a first estimation of the impacts are conducted following the approach developed and successfully applied for two large flash-flood events in two different French regions (Gard in 2002 and Var in 2010) by Le Bihan (2016). A distributed rainfall-runoff model applied at high resolution for the whole area - including numerous small ungauged basins - is used to feed a semi-automatic hydraulic approach (Cartino method) applied along the river network - including small tributaries. Estimation of the impacts is then performed based on the delineation of the flooded areas and geographic databases identifying buildings and population at risk.

Towards a better understanding of flood generation and surface water inundation mechanisms using NASA remote sensing data products

Science.gov (United States)

Lucey, J.; Reager, J. T., II; Lopez, S. R.

2017-12-01

Floods annually cause several weather-related fatalities and financial losses. According to NOAA and FEMA, there were 43 deaths and 18 billion dollars paid out in flood insurance policies during 2005. The goal of this work is to improve flood prediction and flood risk assessment by creating a general model of predictability of extreme runoff generation using various NASA products. Using satellite-based flood inundation observations, we can relate surface water formation processes to changes in other hydrological variables, such as precipitation, storage and soil moisture, and understand how runoff generation response to these forcings is modulated by local topography and land cover. Since it is known that a flood event would cause an abnormal increase in surface water, we examine these underlying physical relationships in comparison with the Dartmouth Flood Observatory archive of historic flood events globally. Using ground water storage observations (GRACE), precipitation (TRMM or GPCP), land use (MODIS), elevation (SRTM) and surface inundation levels (SWAMPS), an assessment of geological and climate conditions can be performed for any location around the world. This project utilizes multiple linear regression analysis evaluating the relationship between surface water inundation, total water storage anomalies and precipitation values, grouped by average slope or land use, to determine their statistical relationships and influences on inundation data. This research demonstrates the potential benefits of using global data products for early flood prediction and will improve our understanding of runoff generation processes.

Probabilistic flood inundation mapping at ungauged streams due to roughness coefficient uncertainty in hydraulic modelling

Science.gov (United States)

Papaioannou, George; Vasiliades, Lampros; Loukas, Athanasios; Aronica, Giuseppe T.

2017-04-01

Probabilistic flood inundation mapping is performed and analysed at the ungauged Xerias stream reach, Volos, Greece. The study evaluates the uncertainty introduced by the roughness coefficient values on hydraulic models in flood inundation modelling and mapping. The well-established one-dimensional (1-D) hydraulic model, HEC-RAS is selected and linked to Monte-Carlo simulations of hydraulic roughness. Terrestrial Laser Scanner data have been used to produce a high quality DEM for input data uncertainty minimisation and to improve determination accuracy on stream channel topography required by the hydraulic model. Initial Manning's n roughness coefficient values are based on pebble count field surveys and empirical formulas. Various theoretical probability distributions are fitted and evaluated on their accuracy to represent the estimated roughness values. Finally, Latin Hypercube Sampling has been used for generation of different sets of Manning roughness values and flood inundation probability maps have been created with the use of Monte Carlo simulations. Historical flood extent data, from an extreme historical flash flood event, are used for validation of the method. The calibration process is based on a binary wet-dry reasoning with the use of Median Absolute Percentage Error evaluation metric. The results show that the proposed procedure supports probabilistic flood hazard mapping at ungauged rivers and provides water resources managers with valuable information for planning and implementing flood risk mitigation strategies.

Wakarusa Watershed Inundation Areas

Data.gov (United States)

Kansas Data Access and Support Center — Dam breach analysis provides a prediction of the extent and timing of flooding from a catastrophic breach of the dams. These results are sufficient for developing...

A coupled hydrological-hydraulic flood inundation model calibrated using post-event measurements and integrated uncertainty analysis in a poorly gauged Mediterranean basin

Science.gov (United States)

Hdeib, Rouya; Abdallah, Chadi; Moussa, Roger; Colin, Francois

2017-04-01

Developing flood inundation maps of defined exceedance probabilities is required to provide information on the flood hazard and the associated risk. A methodology has been developed to model flood inundation in poorly gauged basins, where reliable information on the hydrological characteristics of floods are uncertain and partially captured by the traditional rain-gauge networks. Flood inundation is performed through coupling a hydrological rainfall-runoff (RR) model (HEC-HMS) with a hydraulic model (HEC-RAS). The RR model is calibrated against the January 2013 flood event in the Awali River basin, Lebanon (300 km2), whose flood peak discharge was estimated by post-event measurements. The resulting flows of the RR model are defined as boundary conditions of the hydraulic model, which is run to generate the corresponding water surface profiles and calibrated against 20 post-event surveyed cross sections after the January-2013 flood event. An uncertainty analysis is performed to assess the results of the models. Consequently, the coupled flood inundation model is simulated with design storms and flood inundation maps are generated of defined exceedance probabilities. The peak discharges estimated by the simulated RR model were in close agreement with the results from different empirical and statistical methods. This methodology can be extended to other poorly gauged basins facing common stage-gauge failure or characterized by floods with a stage exceeding the gauge measurement level, or higher than that defined by the rating curve.

A Storm Surge and Inundation Model of the Back River Watershed at NASA Langley Research Center

Science.gov (United States)

Loftis, Jon Derek; Wang, Harry V.; DeYoung, Russell J.

2013-01-01

This report on a Virginia Institute for Marine Science project demonstrates that the sub-grid modeling technology (now as part of Chesapeake Bay Inundation Prediction System, CIPS) can incorporate high-resolution Lidar measurements provided by NASA Langley Research Center into the sub-grid model framework to resolve detailed topographic features for use as a hydrological transport model for run-off simulations within NASA Langley and Langley Air Force Base. The rainfall over land accumulates in the ditches/channels resolved via the model sub-grid was tested to simulate the run-off induced by heavy precipitation. Possessing both the capabilities for storm surge and run-off simulations, the CIPS model was then applied to simulate real storm events starting with Hurricane Isabel in 2003. It will be shown that the model can generate highly accurate on-land inundation maps as demonstrated by excellent comparison of the Langley tidal gauge time series data (CAPABLE.larc.nasa.gov) and spatial patterns of real storm wrack line measurements with the model results simulated during Hurricanes Isabel (2003), Irene (2011), and a 2009 Nor'easter. With confidence built upon the model's performance, sea level rise scenarios from the ICCP (International Climate Change Partnership) were also included in the model scenario runs to simulate future inundation cases.

Assessment of tsunami hazard for coastal areas of Shandong Province, China

Science.gov (United States)

Feng, Xingru; Yin, Baoshu

2017-04-01

Shandong province is located on the east coast of China and has a coastline of about 3100 km. There are only a few tsunami events recorded in the history of Shandong Province, but the tsunami hazard assessment is still necessary as the rapid economic development and increasing population of this area. The objective of this study was to evaluate the potential danger posed by tsunamis for Shandong Province. The numerical simulation method was adopted to assess the tsunami hazard for coastal areas of Shandong Province. The Cornell multi-grid coupled tsunami numerical model (COMCOT) was used and its efficacy was verified by comparison with three historical tsunami events. The simulated maximum tsunami wave height agreed well with the observational data. Based on previous studies and statistical analyses, multiple earthquake scenarios in eight seismic zones were designed, the magnitudes of which were set as the potential maximum values. Then, the tsunamis they induced were simulated using the COMCOT model to investigate their impact on the coastal areas of Shandong Province. The numerical results showed that the maximum tsunami wave height, which was caused by the earthquake scenario located in the sea area of the Mariana Islands, could reach up to 1.39 m off the eastern coast of Weihai city. The tsunamis from the seismic zones of the Bohai Sea, Okinawa Trough, and Manila Trench could also reach heights of >1 m in some areas, meaning that earthquakes in these zones should not be ignored. The inundation hazard was distributed primarily in some northern coastal areas near Yantai and southeastern coastal areas of Shandong Peninsula. When considering both the magnitude and arrival time of tsunamis, it is suggested that greater attention be paid to earthquakes that occur in the Bohai Sea. In conclusion, the tsunami hazard facing the coastal area of Shandong Province is not very serious; however, disasters could occur if such events coincided with spring tides or other

Variation in Assemblages of Small Fishes and Microcrustaceans After Inundation of Rarely Flooded Wetlands of the Lower Okavango Delta, Botswana

Science.gov (United States)

Siziba, Nqobizitha; Chimbari, Moses J.; Masundire, Hillary; Mosepele, Ketlhatlogile; Ramberg, Lars

2013-12-01

Water extraction from floodplain river systems may alter patterns of inundation of adjacent wetlands and lead to loss of aquatic biodiversity. Water reaching the Okavango Delta (Delta), Botswana, may decrease due to excessive water extraction and climate change. However, due to poor understanding of the link between inundation of wetlands and biological responses, it is difficult to assess the impacts of these future water developments on aquatic biota. Large floods from 2009 to 2011 inundated both rarely and frequently flooded wetlands in the Delta, creating an opportunity to examine the ecological significance of flooding of wetlands with widely differing hydrological characteristics. We studied the assemblages of small fishes and microcrustaceans, together with their trophic relationships, in temporary wetlands of the lower Delta. Densities of microcrustaceans in temporary wetlands were generally lower than previously recorded in these habitats. Microcrustacean density varied with wetland types and hydrological phase of inundation. High densities of microcrustaceans were recorded in the 2009 to 2010 flooding season after inundation of rarely flooded sites. Large numbers of small fishes were observed during this study. Community structure of small fishes differed significantly across the studied wetlands, with poeciliids predominant in frequently flooded wetlands and juvenile cichlids most abundant in rarely flooded wetlands (analysis of similarity, P < 0.05). Small fishes of <20 mm fed largely on microcrustaceans and may have led to low microcrustacean densities within the wetlands. This result matched our prediction that rarely flooded wetlands would be more productive; hence, they supported greater populations of microcrustaceans and cichlids, which are aggressive feeders. However, the predominance of microcrustaceans in the guts of small fishes (<20 mm) suggests that predation by fishes may also be an important regulatory mechanism of microcrustacean

Tidal-Fluvial and Estuarine Processes in the Lower Columbia River: II. Water Level Models, Floodplain Wetland Inundation, and System Zones

Energy Technology Data Exchange (ETDEWEB)

Jay, David A.; Borde, Amy B.; Diefenderfer, Heida L.

2016-04-26

Spatially varying water-level regimes are a factor controlling estuarine and tidal-fluvial wetland vegetation patterns. As described in Part I, water levels in the Lower Columbia River and estuary (LCRE) are influenced by tides, river flow, hydropower operations, and coastal processes. In Part II, regression models based on tidal theory are used to quantify the role of these processes in determining water levels in the mainstem river and floodplain wetlands, and to provide 21-year inundation hindcasts. Analyses are conducted at 19 LCRE mainstem channel stations and 23 tidally exposed floodplain wetland stations. Sum exceedance values (SEVs) are used to compare wetland hydrologic regimes at different locations on the river floodplain. A new predictive tool is introduced and validated, the potential SEV (pSEV), which can reduce the need for extensive new data collection in wetland restoration planning. Models of water levels and inundation frequency distinguish four zones encompassing eight reaches. The system zones are the wave- and current-dominated Entrance to river kilometer (rkm) 5; the Estuary (rkm-5 to 87), comprised of a lower reach with salinity, the energy minimum (where the turbidity maximum normally occurs), and an upper estuary reach without salinity; the Tidal River (rkm-87 to 229), with lower, middle, and upper reaches in which river flow becomes increasingly dominant over tides in determining water levels; and the steep and weakly tidal Cascade (rkm-229 to 234) immediately downstream from Bonneville Dam. The same zonation is seen in the water levels of floodplain stations, with considerable modification of tidal properties. The system zones and reaches defined here reflect geological features and their boundaries are congruent with five wetland vegetation zones

The Upper Mississippi River floodscape: spatial patterns of flood inundation and associated plant community distributions

Science.gov (United States)

DeJager, Nathan R.; Rohweder, Jason J.; Yin, Yao; Hoy, Erin E.

2016-01-01

Questions How is the distribution of different plant communities associated with patterns of flood inundation across a large floodplain landscape? Location Thirty-eight thousand nine hundred and seventy hectare of floodplain, spanning 320 km of the Upper Mississippi River (UMR). Methods High-resolution elevation data (Lidar) and 30 yr of daily river stage data were integrated to produce a ‘floodscape’ map of growing season flood inundation duration. The distributions of 16 different remotely sensed plant communities were quantified along the gradient of flood duration. Results Models fitted to the cumulative frequency of occurrence of different vegetation types as a function of flood duration showed that most types exist along a continuum of flood-related occurrence. The diversity of community types was greatest at high elevations (0–10 d of flooding), where both upland and lowland community types were found, as well as at very low elevations (70–180 d of flooding), where a variety of lowland herbaceous communities were found. Intermediate elevations (20–60 d of flooding) tended to be dominated by floodplain forest and had the lowest diversity of community types. Conclusions Although variation in flood inundation is often considered to be the main driver of spatial patterns in floodplain plant communities, few studies have quantified flood–vegetation relationships at broad scales. Our results can be used to identify targets for restoration of historical hydrological regimes or better anticipate hydro-ecological effects of climate change at broad scales.

Regional early flood warning system: design and implementation

Science.gov (United States)

Chang, L. C.; Yang, S. N.; Kuo, C. L.; Wang, Y. F.

2017-12-01

This study proposes a prototype of the regional early flood inundation warning system in Tainan City, Taiwan. The AI technology is used to forecast multi-step-ahead regional flood inundation maps during storm events. The computing time is only few seconds that leads to real-time regional flood inundation forecasting. A database is built to organize data and information for building real-time forecasting models, maintaining the relations of forecasted points, and displaying forecasted results, while real-time data acquisition is another key task where the model requires immediately accessing rain gauge information to provide forecast services. All programs related database are constructed in Microsoft SQL Server by using Visual C# to extracting real-time hydrological data, managing data, storing the forecasted data and providing the information to the visual map-based display. The regional early flood inundation warning system use the up-to-date Web technologies driven by the database and real-time data acquisition to display the on-line forecasting flood inundation depths in the study area. The friendly interface includes on-line sequentially showing inundation area by Google Map, maximum inundation depth and its location, and providing KMZ file download of the results which can be watched on Google Earth. The developed system can provide all the relevant information and on-line forecast results that helps city authorities to make decisions during typhoon events and make actions to mitigate the losses.

MAXIMUM LIKELIHOOD CLASSIFICATION OF HIGH-RESOLUTION SAR IMAGES IN URBAN AREA

Directory of Open Access Journals (Sweden)

M. Soheili Majd

2012-09-01

Full Text Available In this work, we propose a state-of-the-art on statistical analysis of polarimetric synthetic aperture radar (SAR data, through the modeling of several indices. We concentrate on eight ground classes which have been carried out from amplitudes, co-polarisation ratio, depolarization ratios, and other polarimetric descriptors. To study their different statistical behaviours, we consider Gauss, log- normal, Beta I, Weibull, Gamma, and Fisher statistical models and estimate their parameters using three methods: method of moments (MoM, maximum-likelihood (ML methodology, and log-cumulants method (MoML. Then, we study the opportunity of introducing this information in an adapted supervised classification scheme based on Maximum–Likelihood and Fisher pdf. Our work relies on an image of a suburban area, acquired by the airborne RAMSES SAR sensor of ONERA. The results prove the potential of such data to discriminate urban surfaces and show the usefulness of adapting any classical classification algorithm however classification maps present a persistant class confusion between flat gravelled or concrete roofs and trees.

A Risk Assessment Approach to Manage Inundation of Elseya albagula Nests in Impounded Waters: A Win-Win Situation?

Science.gov (United States)

McDougall, A. J.; Espinoza, T.; Hollier, C.; Limpus, D. J.; Limpus, C. J.

2015-03-01

A risk assessment process was used to trial the impact of potential new operating rules on the frequency of nest inundation for the White-throated snapping turtle, Elseya albagula, in the impounded waters of the Burnett River, Queensland, Australia. The proposed operating rules would increase the barrage storage level during the turtle nesting season (May-July) and then would be allowed to reduce to a lower level for incubation for the rest of the year. These proposed operating rules reduce rates of nest inundation by altering water levels in the Ben Anderson Barrage impoundment of the Burnett River. The rules operate throughout the turtle reproductive period and concomitantly improve stability of littoral habitat and fishway operation. Additionally, the proposed rules are expected to have positive socio-economic benefits within the region. While regulated water resources will inherently have a number of negative environmental implications, these potential new operating rules have the capacity to benefit the environment while managing resources in a more sustainable manner. The operating rules have now been enacted in subordinate legislation and require the operator to maintain water levels to minimize turtle nest inundation.

Assessing inundation hazards to nuclear powerplant sites using geologically extended histories of riverine floods, tsunamis, and storm surges

Science.gov (United States)

O'Connor, Jim; Atwater, Brian F.; Cohn, Timothy A.; Cronin, Thomas M.; Keith, Mackenzie K.; Smith, Christopher G.; Mason, Jr., Robert R.

2014-01-01

Most nuclear powerplants in the United States are near rivers, large lakes, or oceans. As evident from the Fukushima Daiichi, Japan, disaster of 2011, these water bodies pose inundation threats. Geologic records can extend knowledge of rare hazards from flooding, storm surges, and tsunamis. This knowledge can aid in assessing the safety of critical structures such as dams and energy plants, for which even remotely possible hazards are pertinent. Quantitative analysis of inundation from geologic records perhaps is most developed for and applied to riverine flood hazards, but because of recent natural disasters, geologic investigations also are now used widely for understanding tsunami hazards and coastal storm surges.

Extraction of lidar-based dune-crest elevations for use in examining the vulnerability of beaches to inundation during hurricanes

Science.gov (United States)

Stockdon, H.F.; Doran, K.S.; Sallenger, A.H.

2009-01-01

The morphology of coastal sand dunes plays an important role in determining how a beach will respond to a hurricane. Accurate measurements of dune height and position are essential for assessing the vulnerability of beaches to extreme coastal change during future landfalls. Lidar topographic surveys provide rapid, accurate, high-resolution datasets for identifying the location, position, and morphology of coastal sand dunes over large stretches of coast. An algorithm has been developed for identification of the crest of the most seaward sand dune that defines the landward limit of the beach system. Based on changes in beach slope along cross-shore transects of lidar data, dune elevation and location can automatically be extracted every few meters along the coastline. Dune elevations in conjunction with storm-induced water levels can be used to predict the type of coastal response (e.g., beach erosion, dune erosion, overwash, or inundation) that may be expected during hurricane landfall. The vulnerability of the beach system at Fire Island National Seashore in New York to the most extreme of these changes, inundation, is assessed by comparing lidar-derived dune elevations to modeled wave setup and storm surge height. The vulnerability of the beach system to inundation during landfall of a Category 3 hurricane is shown to be spatially variable because of longshore variations in dune height (mean elevation 5.44 m, standard deviation 1.32 m). Hurricane-induced mean water levels exceed dune elevations along 70 of the coastal park, making these locations more vulnerable to inundation during a Category 3 storm. ?? 2009 Coastal Education and Research Foundation.

Mapping Hurricane Rita inland storm tide

Science.gov (United States)

Berenbrock, Charles; Mason, Jr., Robert R.; Blanchard, Stephen F.; Simonovic, Slobodan P.

2009-01-01

Flood-inundation data are most useful for decision makers when presented in the context of maps of effected communities and (or) areas. But because the data are scarce and rarely cover the full extent of the flooding, interpolation and extrapolation of the information are needed. Many geographic information systems (GIS) provide various interpolation tools, but these tools often ignore the effects of the topographic and hydraulic features that influence flooding. A barrier mapping method was developed to improve maps of storm tide produced by Hurricane Rita. Maps were developed for the maximum storm tide and at 3-hour intervals from midnight (0000 hour) through noon (1200 hour) on September 24, 2005. The improved maps depict storm-tide elevations and the extent of flooding. The extent of storm-tide inundation from the improved maximum storm-tide map was compared to the extent of flood-inundation from a map prepared by the Federal Emergency Management Agency (FEMA). The boundaries from these two maps generally compared quite well especially along the Calcasieu River. Also a cross-section profile that parallels the Louisiana coast was developed from the maximum storm-tide map and included FEMA high-water marks.

Integrating heterogeneous earth observation data for assessment of high-resolution inundation boundaries generated during flood emergencies.

Science.gov (United States)

Sava, E.; Cervone, G.; Kalyanapu, A. J.; Sampson, K. M.

2017-12-01

The increasing trend in flooding events, paired with rapid urbanization and an aging infrastructure is projected to enhance the risk of catastrophic losses and increase the frequency of both flash and large area floods. During such events, it is critical for decision makers and emergency responders to have access to timely actionable knowledge regarding preparedness, emergency response, and recovery before, during and after a disaster. Large volumes of data sets derived from sophisticated sensors, mobile phones, and social media feeds are increasingly being used to improve citizen services and provide clues to the best way to respond to emergencies through the use of visualization and GIS mapping. Such data, coupled with recent advancements in data fusion techniques of remote sensing with near real time heterogeneous datasets have allowed decision makers to more efficiently extract precise and relevant knowledge and better understand how damage caused by disasters have real time effects on urban population. This research assesses the feasibility of integrating multiple sources of contributed data into hydrodynamic models for flood inundation simulation and estimating damage assessment. It integrates multiple sources of high-resolution physiographic data such as satellite remote sensing imagery coupled with non-authoritative data such as Civil Air Patrol (CAP) and `during-event' social media observations of flood inundation in order to improve the identification of flood mapping. The goal is to augment remote sensing imagery with new open-source datasets to generate flood extend maps at higher temporal and spatial resolution. The proposed methodology is applied on two test cases, relative to the 2013 Boulder Colorado flood and the 2015 floods in Texas.

Effects of the length of inundation periods on investment in tuber biomass and sexual reproduction by Vallisneria spinulosa S.Z. Yan Ramets

Directory of Open Access Journals (Sweden)

Fox A.D.

2014-05-01

Full Text Available Modification and reductions in flows are reducing inundation times in some Yangtze River wetlands, potentially affecting the growth of submerged macrophytes. The effects of shortening the inundation period from April to October (control to April to September (treatment were tested on the production of surface and below-ground tubers and fruits in individual Vallisneria spinulosa ramets in microcosm experiments. Mean numbers of below-ground tubers produced did not differ significantly between treatments, but individual tuber dry mass was significantly greater when harvested in October compared with plants harvested in September. Significantly more surface tubers were initiated by the ramets in the later harvest, but these did not differ in dry mass. Fewer ramets had initiated sexual reproduction by the September harvest compared with the October harvest. Almost all October fruits were mature, while the ratio of mature to unripe fruits was significantly greater than in September. There was no support for the hypothesis that more tubers were initiated deeper in the substrate with a longer inundation period to avoid predation by fish or birds. Based on these results, shortening of the inundation periods experienced by Vallisneria spinulosa plants in Yangtze River ephemeral wetlands may reduce the dry biomass of below-ground tubers and the production of surface tubers in this keystone macrophyte.

Does an ant-dispersed plant, Viola reichenbachiana, suffer from reduced seed dispersal under inundation disturbances?

NARCIS (Netherlands)

Prinzing, A.; Dauber, J.; Hammer, E.; Hammouti, N.; Bohning-Gaese, K.

2008-01-01

Many plant species use ants as seed dispersers. This dispersal mode is considered to be susceptible to disturbances, but the effect of natural, small-scale disturbances is still unknown. We investigated how small-scale disturbances due to inundation affect seed dispersal in Viola reichenbachiana, a

Objective rapid delineation of areas at risk from block-and-ash pyroclastic flows and surges

Science.gov (United States)

Widiwijayanti, C.; Voight, B.; Hidayat, D.; Schilling, S.P.

2009-01-01

Assessments of pyroclastic flow (PF) hazards are commonly based on mapping of PF and surge deposits and estimations of inundation limits, and/or computer models of varying degrees of sophistication. In volcanic crises a PF hazard map may be sorely needed, but limited time, exposures, or safety aspects may preclude fieldwork, and insufficient time or baseline data may be available for reliable dynamic simulations. We have developed a statistically constrained simulation model for block-and-ash type PFs to estimate potential areas of inundation by adapting methodology from Iverson et al. (Geol Soc America Bull 110:972-984, (1998) for lahars. The predictive equations for block-and-ash PFs are calibrated with data from several volcanoes and given by A = (0.05 to 0.1) V2/3, B = (35 to 40) V2/3, where A is cross-sectional area of inundation, B is planimetric area and V is deposit volume. The proportionality coefficients were obtained from regression analyses and comparison of simulations to mapped deposits. The method embeds the predictive equations in a GIS program coupled with DEM topography, using the LAHARZ program of Schilling (1998). Although the method is objective and reproducible, any PF hazard zone so computed should be considered as an approximate guide only, due to uncertainties on the coefficients applicable to individual PFs, the authenticity of DEM details, and the volume of future collapses. The statistical uncertainty of the predictive equations, which imply a factor of two or more in predicting A or B for a specified V, is superposed on the uncertainty of forecasting V for the next PF to descend a particular valley. Multiple inundation zones, produced by simulations using a selected range of volumes, partly accommodate these uncertainties. The resulting maps show graphically that PF inundation potentials are highest nearest volcano sources and along valley thalwegs, and diminish with distance from source and lateral distance from thalweg. The model does

Integration of contributed data with HEC-RAS hydrodynamic model for flood inundation and damage assessment: 2015 Dallas Texas Case Study

Science.gov (United States)

Sava, E.; Thornton, J. C.; Kalyanapu, A. J.; Cervone, G.

2016-12-01

Transportation infrastructure networks in urban areas are highly sensitive to natural disasters, yet are a very critical source for the success of rescue, recovery, and renovation operations. Therefore, prompt restoration of such networks is of high importance for disaster relief services. Satellite and aerial images provide data with high spatial and temporal resolution and are a powerful tool for monitoring the environment and mapping the spatio-temporal variability of the Earth's surface. They provide a synoptic overview and give useful environmental information for a wide range of scales, from entire continents to urban areas, with spatial pixel resolutions ranging from kilometers to centimeters. However, sensor limitations are often a serious drawback since no single sensor offers the optimal spectral, spatial, and temporal resolution at the same time. Specific data may not be collected in the time and space most urgently required and/or may it contain gaps as a result of the satellite revisit time, atmospheric opacity, or other obstructions. In this study, the feasibility of integrating multiple sources of contributed data including remotely sensed datasets and open-source geospatial datasets, into hydrodynamic models for flood inundation simulations is assessed. The 2015 Dallas floods that caused up to $61 million dollars in damage was selected for this study. A Hydraulic Engineering Center - River Analysis System (HEC-RAS) model was developed for the study area, using reservoir surcharge releases and geometry provided by the U.S. Army Corps of Engineers Fort Worth District. The simulated flood inundation is compared with the "contributed data" for the location (such as Civil Air Patrol data and WorldView 3 dataset) which indicated the model's lack of representing lateral inflows near the upstream section. An Artificial Neural Network (ANN) model is developed that used local precipitation and discharge values in the vicinity to estimate the lateral flows

Nowcasting, forecasting and hindcasting Harvey and Irma inundation in near-real time using a continental 2D hydrodynamic model

Science.gov (United States)

Sampson, C. C.; Wing, O.; Quinn, N.; Smith, A.; Neal, J. C.; Schumann, G.; Bates, P.

2017-12-01

During an ongoing natural disaster data are required on: (1) the current situation (nowcast); (2) its likely immediate evolution (forecast); and (3) a consistent view post-event of what actually happened (hindcast or reanalysis). We describe methods used to achieve all three tasks for flood inundation during the Harvey and Irma events using a continental scale 2D hydrodynamic model (Wing et al., 2017). The model solves the local inertial form of the Shallow Water equations over a regular grid of 1 arcsecond ( 30m). Terrain data are taken from the USGS National Elevation Dataset with known flood defences represented using the U.S. Army Corps of Engineers National Levee Dataset. Channels are treated as sub-grid scale features using the HydroSHEDS global hydrography data set. The model is driven using river flows, rainfall and coastal water levels. It simulates river flooding in basins > 50 km2, and fluvial and coastal flooding everywhere. Previous wide area validation tests show this model to be capable of matching FEMA maps and USGS local models built with bespoke data with hit rates of 86% and 92% respectively (Wing et al., 2017). Boundary conditions were taken from NOAA QPS data to produce nowcast and forecast simulations in near real time, before updating with NOAA observations to produce the hindcast. During the event simulation results were supplied to major insurers and multi-nationals who used them to estimate their likely capital exposure and to mitigate flood damage to their infrastructure whilst the event was underway. Simulations were validated against modelled flood footprints computed by FEMA and USACE, and composite satellite imagery produced by the Dartmouth Flood Observatory. For the Harvey event, hit rates ranged from 60-84% against these data sources, but a lack of metadata meant it was difficult to perform like-for-like comparisons. The satellite data also appeared to miss known flooding in urban areas that was picked up in the models. Despite

Mapping Pyroclastic Flow Inundation Using Radar and Optical Satellite Images and Lahar Modeling

Directory of Open Access Journals (Sweden)

Chang-Wook Lee

2018-01-01

Full Text Available Sinabung volcano, located above the Sumatra subduction of the Indo-Australian plate under the Eurasian plate, became active in 2010 after about 400 years of quiescence. We use ALOS/PALSAR interferometric synthetic aperture radar (InSAR images to measure surface deformation from February 2007 to January 2011. We model the observed preeruption inflation and coeruption deflation using Mogi and prolate spheroid sources to infer volume changes of the magma chamber. We interpret that the inflation was due to magma accumulation in a shallow reservoir beneath Mount Sinabung and attribute the deflation due to magma withdrawal from the shallow reservoir during the eruption as well as thermoelastic compaction of erupted material. The pyroclastic flow extent during the eruption is then derived from the LAHARZ model based on the coeruption volume from InSAR modeling and compared to that derived from the Landsat 7 Enhanced Thematic Mapper Plus (ETM+ image. The pyroclastic flow inundation extents between the two different methods agree at about 86%, suggesting the capability of mapping pyroclastic flow inundation by combing radar and optical imagery as well as flow modeling.

Predicting the Effects of Man-Made Fishing Canals on Floodplain Inundation - A Modelling Study

Science.gov (United States)

Shastry, A. R.; Durand, M. T.; Neal, J. C.; Fernandez, A.; Hamilton, I.; Kari, S.; Laborde, S.; Mark, B. G.; Arabi, M.; Moritz, M.; Phang, S. C.

2016-12-01

The Logone floodplain in northern Cameroon is an excellent example of coupled human-natural systems because of strong couplings between the social, ecological and hydrologic systems. Overbank flow from the Logone River in September and October is essential for agriculture and fishing livelihoods. Fishers dig canals to catch fish during the flood's recession to the river in November and December by installing nets at the intersection of canals and the river. Fishing canals connect the river to natural depressions in the terrain and may serve as a man-made extension of the river drainage network. In the last four decades, there has been an exponential increase in the number of canals which may affect flood hydraulics and the fishery. The goal of this study is to characterize the relationship between the fishing canals and flood dynamics in the Logone floodplain, specifically, parameters of flooding and recession timings and the duration of inundation. To do so, we model the Bara region ( 30 km2) of the floodplain using LISFLOOD-FP, a two-dimensional hydrodynamic model with sub-grid parameterizations of canals. We use a simplified version of the hydraulic system at a grid-cell size of 30-m, using synthetic topography, parameterized fishing canals, and representing fishnets as a combination of weir and mesh screens. The inflow at Bara is obtained from a separate, lower resolution (1-km grid-cell) model forced by daily discharge records obtained from Katoa, located 25-km upstream of Bara. Preliminary results show more canals lead to early recession of flood and a shorter duration of flood inundation. A shorter duration of flood inundation reduces the period of fish growth and will affect fisher catch returns. Understanding the couplings within the system is important for predicting long-term dynamics and the impact of building more fishing canals.

Estimated Flood-Inundation Mapping for the Upper Blue River, Indian Creek, and Dyke Branch in Kansas City, Missouri, 2006-08

Science.gov (United States)

Kelly, Brian P.; Huizinga, Richard J.

2008-01-01

In the interest of improved public safety during flooding, the U.S. Geological Survey, in cooperation with the city of Kansas City, Missouri, completed a flood-inundation study of the Blue River in Kansas City, Missouri, from the U.S. Geological Survey streamflow gage at Kenneth Road to 63rd Street, of Indian Creek from the Kansas-Missouri border to its mouth, and of Dyke Branch from the Kansas-Missouri border to its mouth, to determine the estimated extent of flood inundation at selected flood stages on the Blue River, Indian Creek, and Dyke Branch. The results of this study spatially interpolate information provided by U.S. Geological Survey gages, Kansas City Automated Local Evaluation in Real Time gages, and the National Weather Service flood-peak prediction service that comprise the Blue River flood-alert system and are a valuable tool for public officials and residents to minimize flood deaths and damage in Kansas City. To provide public access to the information presented in this report, a World Wide Web site (http://mo.water.usgs.gov/indep/kelly/blueriver) was created that displays the results of two-dimensional modeling between Hickman Mills Drive and 63rd Street, estimated flood-inundation maps for 13 flood stages, the latest gage heights, and National Weather Service stage forecasts for each forecast location within the study area. The results of a previous study of flood inundation on the Blue River from 63rd Street to the mouth also are available. In addition the full text of this report, all tables and maps are available for download (http://pubs.usgs.gov/sir/2008/5068). Thirteen flood-inundation maps were produced at 2-foot intervals for water-surface elevations from 763.8 to 787.8 feet referenced to the Blue River at the 63rd Street Automated Local Evaluation in Real Time stream gage operated by the city of Kansas City, Missouri. Each map is associated with gages at Kenneth Road, Blue Ridge Boulevard, Kansas City (at Bannister Road), U.S. Highway 71

Modeling for the SAFRR Tsunami Scenario-generation, propagation, inundation, and currents in ports and harbors: Chapter D in The SAFRR (Science Application for Risk Reduction) Tsunami Scenario

Science.gov (United States)

,

2013-01-01

This U.S. Geological Survey (USGS) Open-File report presents a compilation of tsunami modeling studies for the Science Application for Risk Reduction (SAFRR) tsunami scenario. These modeling studies are based on an earthquake source specified by the SAFRR tsunami source working group (Kirby and others, 2013). The modeling studies in this report are organized into three groups. The first group relates to tsunami generation. The effects that source discretization and horizontal displacement have on tsunami initial conditions are examined in section 1 (Whitmore and others). In section 2 (Ryan and others), dynamic earthquake rupture models are explored in modeling tsunami generation. These models calculate slip distribution and vertical displacement of the seafloor as a result of realistic fault friction, physical properties of rocks surrounding the fault, and dynamic stresses resolved on the fault. The second group of papers relates to tsunami propagation and inundation modeling. Section 3 (Thio) presents a modeling study for the entire California coast that includes runup and inundation modeling where there is significant exposure and estimates of maximum velocity and momentum flux at the shoreline. In section 4 (Borrero and others), modeling of tsunami propagation and high-resolution inundation of critical locations in southern California is performed using the National Oceanic and Atmospheric Administration’s (NOAA) Method of Splitting Tsunami (MOST) model and NOAA’s Community Model Interface for Tsunamis (ComMIT) modeling tool. Adjustments to the inundation line owing to fine-scale structures such as levees are described in section 5 (Wilson). The third group of papers relates to modeling of hydrodynamics in ports and harbors. Section 6 (Nicolsky and Suleimani) presents results of the model used at the Alaska Earthquake Information Center for the Ports of Los Angeles and Long Beach, as well as synthetic time series of the modeled tsunami for other selected

Áreas inundáveis - Um desafio para Limnologia

OpenAIRE

Junk, Woifgang Johannes

1980-01-01

Resumo No decorrer de estudos limnológicos nas áreas inundáveis (várzea) do Médio Amazonas, encontraram-se dificuldades na aplicação da terminologia, dos conceitos e da metodologia desenvolvidas para os sistemas clássicos de água parada e água corrente. As pronunciadas oscilações periódicas do nível de água, em combinação com mudanças entre a fase aquática e a fase terrestre em grande escala, provocam condições, que não correspondem nem a lagos e rios nem a pântanos e águas temporárias. Uma r...

The Blackwater NWR inundation model. Rising sea level on a low-lying coast: land use planning for wetlands

Science.gov (United States)

Larsen, Curt; Clark, Inga; Guntenspergen, Glenn; Cahoon, Don; Caruso, Vincent; Hupp, Cliff; Yanosky, Tom

2004-01-01

The Blackwater National Wildlife Refuge (BNWR), on the Eastern Shore of Chesapeake Bay (figure 1), occupies an area less than 1 meter above sea level. The Refuge has been featured prominently in studies of the impact of sea level rise on coastal wetlands. Most notably, the refuge has been sited by the Intergovernmental Panel on Climate Change (IPCC) as a key example of 'wetland loss' attributable to rising sea level due to global temperature increase. Comparative studies of aerial photos taken since 1938 show an expanding area of open water in the central area of the refuge. The expanding area of open water can be shown to parallel the record of sea level rise over the past 60 years. The U.S. Fish and Wildlife Service (FWS) manages the refuge to support migratory waterfowl and to preserve endangered upland species. High marsh vegetation is critical to FWS waterfowl management strategies. A broad area once occupied by high marsh has decreased with rising sea level. The FWS needs a planning tool to help predict current and future areas of high marsh available for waterfowl. 'Wetland loss' is a relative term. It is dependant on the boundaries chosen for measurement. Wetland vegetation, zoned by elevation and salinity (figure 3), respond to rising sea level. Wetlands migrate inland and upslope and may vary in areas depending on the adjacent land slopes. Refuge managers need a geospatial tool that allows them to predict future areas that will be converted to high and intertidal marsh. Shifts in location and area of coverage must be anticipated. Viability of a current marsh area is also important. When will sea level rise make short-term management strategies to maintain an area impractical? The USGS has developed an inundation model for the BNWR centered on the refuge and surrounding areas. Such models are simple in concept, but they require a detailed topographic map upon which to superimpose future sea level positions. The new system of LIDAR mapping of land and

Potential Impact of Climate Changes on the Inundation Risk Levels in a Dam Break Scenario

Directory of Open Access Journals (Sweden)

Sudha Yerramilli

2013-03-01

Full Text Available The overall objective of the study is to generate information for an enhanced land use planning with respect to flood hazards. The study assesses the potential impact of climate change by simulating a dam break scenario in a high intensity rainfall event and evaluates the vulnerability risk in the downstream region by integrating ArcGIS and Hydrologic Engineering Centers River Analysis System (HEC-RAS technologies. In the past century, the evidence of climate changes are observed in terms of increase in high intensity rainfall events. These events are of high concern, as increased inflow rates may increase the probability of a dam failure, leading to higher magnitude flooding events involving multiple consequences. The 100 year historical rainfall data for the central Mississippi region reveals an increased trend in the intensity of rainfall rates after the 1970s. With more than 10% of high hazard dams in the central region, the damage can be far accumulative. The study determines occurrence of the high intensity rainfall event in the past 100 years for central Mississippi and simulates a Ross Barnett Reservoir dam break scenario and evaluates the vulnerability risks due to inundation in the immediate downstream region, which happens to be the State Capital. The results indicate that the inundation due to a Ross Barnett Reservoir failure under high intensity rainfall event is comparable to a catastrophic flood event experienced by the region in 1979, which almost equals a 200-year flood magnitude. The results indicate that the extent and depth of flood waters poses a significant destructive threat to the state capital, inundating various infrastructural and transportation networks.

Maximum power point tracking

International Nuclear Information System (INIS)

Enslin, J.H.R.

1990-01-01

A well engineered renewable remote energy system, utilizing the principal of Maximum Power Point Tracking can be m ore cost effective, has a higher reliability and can improve the quality of life in remote areas. This paper reports that a high-efficient power electronic converter, for converting the output voltage of a solar panel, or wind generator, to the required DC battery bus voltage has been realized. The converter is controlled to track the maximum power point of the input source under varying input and output parameters. Maximum power point tracking for relative small systems is achieved by maximization of the output current in a battery charging regulator, using an optimized hill-climbing, inexpensive microprocessor based algorithm. Through practical field measurements it is shown that a minimum input source saving of 15% on 3-5 kWh/day systems can easily be achieved. A total cost saving of at least 10-15% on the capital cost of these systems are achievable for relative small rating Remote Area Power Supply systems. The advantages at larger temperature variations and larger power rated systems are much higher. Other advantages include optimal sizing and system monitor and control

Wetland Loss Patterns and Inundation-Productivity Relationships Prognosticate Widespread Salt Marsh Loss for Southern New England

Science.gov (United States)

Tidal salt marsh is a key defense against, yet is especially vulnerable to, the effects of accelerated sea level rise. To determine whether salt marshes in southern New England will be stable given increasing inundation over the coming decades, we examined current loss patterns, ...

Inundation and Gas Fluxes from Amazon Lakes and Wetlands

Science.gov (United States)

Melack, J. M.; MacIntyre, S.; Forsberg, B. R.; Amaral, J. H.; Barbosa, P.

2015-12-01

Inundation areas and wetland habitats for the lowland Amazon basin derived remote sensing with synthetic aperture radar are combined with measurements of greenhouse gas evasion derived from field measurements and new formulations of atmosphere-water. On-going field studies in representative aquatic habitats on the central Amazon floodplain are combining monthly measurements of carbon dioxide and methane concentrations and fluxes to the atmosphere with deployment of meteorological sensors and high-resolution thermistors and optical dissolved oxygen sensors. A real-time cavity ringdown spectrometer is being used to determine the gas concentrations; vertical profiles were obtained by using an equilibrator to extract gases from water, and floating chambers are used to assess fluxes. Gas fluxes varied as a function of season, habitat and water depth. Greatest carbon dioxide fluxes occurred during high and falling water levels. During low water, periods with high chlorophyll, indicative of phytoplankton, the flux of carbon dioxide switched from being emitted from the lake to being taken-up by the lake some of the time. The highest pCO2 concentration (5500 μatm) was about three times higher than the median (1700 μatm). Higher CO2 fluxes were observed in open water than in areas with flooded or floating vegetation. In contrast, methane fluxes were higher in vegetated regions. We measured turbulence as rate of dissipation of turbulent kinetic energy based on microstructure profiling. Comparison of these measurements with those calculated from meteorological and time series measurements validated new equations for turbulent kinetic energy dissipation (TKE) rates during moderate winds and cooling and illustrated that the highest dissipation rates occurred under heating. Measured gas exchange coefficients (k600) were similar to those based on the TKE dissipation rates and are well described using the surface renewal model. These k values are several times higher than

Utilizing GNSS Reflectometry to Assess Surface Inundation Dynamics in Tropical Wetlands

Science.gov (United States)

Jensen, K.; McDonald, K. C.; Podest, E.; Chew, C. C.

2017-12-01

Tropical wetlands play a significant role in global atmospheric methane and terrestrial water storage. Despite the growing number of remote sensing products from satellite sensors, both spatial distribution and temporal variability of wetlands remain highly uncertain. An emerging innovative approach to mapping wetlands is offered by GNSS reflectometry (GNSS-R), a bistatic radar concept that takes advantage of GNSS transmitting satellites to yield observations with global coverage and rapid revisit time. This technology offers the potential to capture dynamic inundation changes in wetlands at higher temporal fidelity and sensitivity under the canopy than presently possible. We present an integrative analysis of radiometric modeling, ground measurements, and several microwave remote sensing datasets traditionally used for wetland observations. From a theoretical standpoint, GNSS-R sensitivities for vegetation and wetlands are investigated with a bistatic radar model in order to understand the interactions of the signal with various land surface components. GNSS reflections from the TechDemoSat-1 (TDS-1), Soil Moisture Active Passive (SMAP), and Cyclone GNSS (CYGNSS) missions are tested experimentally with contemporaneous (1) field measurements collected from the Pacaya Samiria National Reserve in the Peruvian Amazon, (2) imaging radar from Sentinel-1 and PALSAR-2 observed over a variety of tropical wetland systems, and (3) pan-tropical coarse-resolution (25km) microwave datasets (Surface Water Microwave Product Series). We find that GNSS-R data provide the potential to extend capabilities of current remote sensing techniques to characterize surface inundation extent, and we explore how to maximize synergism between different satellite sensors to produce an enhanced wetland monitoring product.

Community exposure to tsunami hazards in California

Science.gov (United States)

Wood, Nathan J.; Ratliff, Jamie; Peters, Jeff

2013-01-01

Evidence of past events and modeling of potential events suggest that tsunamis are significant threats to low-lying communities on the California coast. To reduce potential impacts of future tsunamis, officials need to understand how communities are vulnerable to tsunamis and where targeted outreach, preparedness, and mitigation efforts may be warranted. Although a maximum tsunami-inundation zone based on multiple sources has been developed for the California coast, the populations and businesses in this zone have not been documented in a comprehensive way. To support tsunami preparedness and risk-reduction planning in California, this study documents the variations among coastal communities in the amounts, types, and percentages of developed land, human populations, and businesses in the maximum tsunami-inundation zone. The tsunami-inundation zone includes land in 94 incorporated cities, 83 unincorporated communities, and 20 counties on the California coast. According to 2010 U.S. Census Bureau data, this tsunami-inundation zone contains 267,347 residents (1 percent of the 20-county resident population), of which 13 percent identify themselves as Hispanic or Latino, 14 percent identify themselves as Asian, 16 percent are more than 65 years in age, 12 percent live in unincorporated areas, and 51 percent of the households are renter occupied. Demographic attributes related to age, race, ethnicity, and household status of residents in tsunami-prone areas demonstrate substantial range among communities that exceed these regional averages. The tsunami-inundation zone in several communities also has high numbers of residents in institutionalized and noninstitutionalized group quarters (for example, correctional facilities and military housing, respectively). Communities with relatively high values in the various demographic categories are identified throughout the report. The tsunami-inundation zone contains significant nonresidential populations based on 2011 economic

A comparison between two inundation models for the 25 Ooctober 2010 Mentawai Islands Tsunami

Science.gov (United States)

Huang, Z.; Borrero, J. C.; Qiu, Q.; Hill, E. M.; Li, L.; Sieh, K. E.

2011-12-01

On 25 October 2010, an Mw~7.8 earthquake occurred on the Sumatra megathrust seaward of the Mentawai Islands, Indonesia, generating a tsunami which killed approximately 500 people. Following the event, the Earth Observatory of Singapore (EOS) initiated a post-tsunami field survey, collecting tsunami run-up data from more than 30 sites on Pagai Selatan, Pagai Utara and Sipora. The strongest tsunami effects were observed on several small islands offshore of Pagai Selatan, where runup exceeded 16 m. This presentation will focus on a detailed comparison between two tsunami propagation and inundation models: COMCOT (Cornell Multi-grid Coupled Tsunami model) and MOST (Method of Splitting Tsunami). Simulations are initialized using fault models based on data from a 1-hz GPS system that measured co-seismic deformation throughout the region. Preliminary simulations suggest that 2-m vertical seafloor deformation over a reasonably large area is required to recreate most of the observed tsunami effects. Since the GPS data suggest that subsidence of the islands is small, this implies that the tsunami source region is somewhat narrower and located further offshore than described in recently published earthquake source models based on teleseismic inversions alone. We will also discuss issues such as bathymetric and topographic data preparation and the uncertainty in the modeling results due to the lack of high resolution bathymetry and topography in the study area.

Capturing variations in inundation with satellite remote sensing in a morphologically complex, large lake

Science.gov (United States)

Wu, Guiping; Liu, Yuanbo

2015-04-01

Poyang Lake is the largest freshwater lake in China, with high morphological complexity from south to north. In recent years, the lake has experienced expansion and shrinkage processes over both short- and long-term scales, resulting in significant hydrological, ecological and economic problems. Exactly how and how rapidly the processes of spatial change have occurred in the lake during the expansion and shrinkage periods is unknown. Such knowledge is of great importance for policymakers as it may help with flood/drought prevention, land use planning and lake ecological conservation. In this study, we investigated the spatial-temporal distribution and changing processes of inundation in Poyang Lake based on Moderate Resolution Imaging Spectroradiometer (MODIS) Level-1B data from 2000 to 2011. A defined water variation rate (WVR) and inundation frequency (IF) indicator revealed the water surface submersion and exposure processes of lake expansion and shrinkage in different zones which were divided according to the lake's hydrological and topographic features. Regional differences and significant seasonality variability were found in the annual and monthly mean IF. The monthly mean IF increased slowly from north to south during January-August but decreased quickly from south to north during September-December. During the lake expansion period, the lake-type water body zone (Zone II) had the fastest expansion rate, with a mean monthly WVR value of 34.47% in February-March, and was followed by the channel-type water body zone (Zone I) in March-May (22.47%). However, during the lake shrinkage period, rapid shrinkage first appeared around the alluvial delta zones in August-October. The sequence of lake surface shrinkage from August to December is exactly opposite to that of lake expansion from February to July. These complex inundation characteristics and changing process were driven by the high temporal variability of the river flows, the morphological diversity of the

Analysis and inundation mapping of the April-May 2011 flood at selected locations in northern and eastern Arkansas and southern Missouri

Science.gov (United States)

Westerman, Drew A.; Merriman, Katherine R.; De Lanois, Jeanne L.; Berenbrock, Charles

2013-01-01

Precipitation that fell from April 19 through May 3, 2011, resulted in widespread flooding across northern and eastern Arkansas and southern Missouri. The first storm produced a total of approximately 16 inches of precipitation over an 8-day period, and the following storms produced as much as 12 inches of precipitation over a 2-day period. Moderate to major flooding occurred quickly along many streams within Arkansas and Missouri (including the Black, Cache, Illinois, St. Francis, and White Rivers) at levels that had not been seen since the historic 1927 floods. The 2011 flood claimed an estimated 21 lives in Arkansas and Missouri, and damage caused by the flooding resulted in a Federal Disaster Declaration for 59 Arkansas counties that received Federal or State assistance. To further the goal of documenting and understanding floods, the U.S. Geological Survey, in cooperation with the Federal Emergency Management Agency, the U.S. Army Corps of Engineers–Little Rock and Memphis Districts, and Arkansas Natural Resources Commission, conducted a study to summarize meteorological and hydrological conditions before the flood; computed flood-peak magnitudes for 39 streamgages; estimated annual exceedance probabilities for 37 of those streamgages; determined the joint probabilities for 11 streamgages paired to the Mississippi River at Helena, Arkansas, which refers to the probability that locations on two paired streams simultaneously experience floods of a magnitude greater than or equal to a given annual exceedance probability; collected high-water marks; constructed flood-peak inundation maps showing maximum flood extent and water depths; and summarized flood damages and effects. For the period of record used in this report, peak-of-record stage occurred at 24 of the 39 streamgages, and peak-of-record streamflow occurred at 13 of the 30 streamgages where streamflow was determined. Annual exceedance probabilities were estimated to be less than 0.5 percent at three

Floodplain inundation response to climate, valley form, and flow regulation on a gravel-bed river in a Mediterranean-climate region

Science.gov (United States)

Cienciala, P.; Pasternack, G. B.

2017-04-01

Floodplain inundation regime defines hydrological connectivity between river channel and floodplain and thus strongly controls structure and function of these highly diverse and productive ecosystems. We combined an extensive LiDAR data set on topography and vegetation, long-term hydrological records, as well as the outputs of hydrological and two-dimensional hydraulic models to examine how floodplain inundation regimes in a dynamic, regulated, gravel-cobble river in a Mediterranean-climate region are controlled by reach-scale valley morphology, hydroclimatic conditions, and flow regulation. Estimated relative differences in the extent, duration, and cumulative duration of inundation events were often as large as an order of magnitude and generally greatest for large and long duration events. The relative impact of flow regulation was greatest under dry hydroclimatic conditions. Although the effects of hydroclimate and flow impairment are larger than that of valley floor topography, the latter controls sensitivity of floodplain hydroperiod to flow regime changes and should not be ignored. These quantitative estimates of the relative importance of factors that control floodplain processes in Mediterranean, semiarid rivers contributes to better understanding of hydrology and geomorphology of this important class of channels. We also discuss implications of our findings for processes that shape floodplain habitat for riparian vegetation and salmonid fish, especially in the context of ecological restoration.

Effect of inundation, oxygen and temperature on carbon mineralization in boreal ecosystems.

Science.gov (United States)

Kim, Youngil; Ullah, Sami; Roulet, Nigel T; Moore, Tim R

2015-04-01

The inundation of boreal forests and peatlands through the construction of hydroelectric reservoirs can increase carbon dioxide (CO2) and methane (CH4) emission. To establish controls on emission rates, we incubated samples of forest and peat soils, spruce litter, forest litter and peatland litter collected from boreal ecosystems in northern Quebec for 16 weeks and measured CO2 and CH4 production rates under flooded or non-flooded conditions and varying oxygen concentration and temperature. CO2 production under flooded conditions was less than under non-flooded conditions (5-71 vs. 5-85 mg Cg(-1) C), but CH4 production under flooded conditions was larger than under non-flooded conditions (1-8158 vs. 0-86 μg Cg(-1) C). The average CO2 and CH4 production rate factor for flooded:non-flooded conditions was 0.76 and 1.32, respectively. Under flooded conditions, high oxygen concentrations increased CO2 production in peat soils but decreased CH4 production in forest and peat soils and spruce litter. Warmer temperatures (from 4 to 22°C) raised both CO2 production in peat soils and peatland litter, and CH4 production in peat soils and spruce litter. This study shows that the direction and/or strength of CO2 and CH4 fluxes change once boreal forests and peatlands are inundated. Copyright © 2014 Elsevier B.V. All rights reserved.

Preliminary assessment of coastal erosion and local community adaptation in Sayung coastal area, central Java – Indonesia

OpenAIRE

Marfai, Muh Aris

2012-01-01

Dynamic environment in coastal area, especially due to coastal erosion process, has negative impact on human environment. Sayung coastal area, located in Central Java-Indonesia, has experienced severe impact of coastal erosion. As the result of the coastal erosion, hundreds of settlement located in coastal area has been destructed. Moreover, fishponds as the land use dominated in the coastal area also has been severely destroyed. Besides the coastal erosion, increasing of inundated area due t...

Coastal Flooding in Florida's Big Bend Region with Application to Sea Level Rise Based on Synthetic Storms Analysis

Directory of Open Access Journals (Sweden)

Scott C. Hagen Peter Bacopoulos

2012-01-01

Full Text Available Flooding is examined by comparing maximum envelopes of water against the 0.2% (= 1-in-500-year return-period flooding surface generated as part of revising the Federal Emergency Management Agency¡¦s flood insurance rate maps for Franklin, Wakulla, and Jefferson counties in Florida¡¦s Big Bend Region. The analysis condenses the number of storms to a small fraction of the original 159 used in production. The analysis is performed by assessing which synthetic storms contributed to inundation extent (the extent of inundation into the floodplain, coverage (the overall surface area of the inundated floodplain and the spatially variable 0.2% flooding surface. The results are interpreted in terms of storm attributes (pressure deficit, radius to maximum winds, translation speed, storm heading, and landfall location and the physical processes occurring within the natural system (storms surge and waves; both are contextualized against existing and new hurricane scales. The approach identifies what types of storms and storm attributes lead to what types of inundation, as measured in terms of extent and coverage, in Florida¡¦s Big Bend Region and provides a basis in the identification of a select subset of synthetic storms for studying the impact of sea level rise. The sea level rise application provides a clear contrast between a dynamic approach versus that of a static approach.

Coarse Resolution SAR Imagery to Support Flood Inundation Models in Near Real Time

Science.gov (United States)

Di Baldassarre, Giuliano; Schumann, Guy; Brandimarte, Luigia; Bates, Paul

2009-11-01

In recent years, the availability of new emerging data (e.g. remote sensing, intelligent wireless sensors, etc) has led to a sudden shift from a data-sparse to a data-rich environment for hydrological and hydraulic modelling. Furthermore, the increased socioeconomic relevance of river flood studies has motivated the development of complex methodologies for the simulation of the hydraulic behaviour of river systems. In this context, this study aims at assessing the capability of coarse resolution SAR (Synthetic Aperture Radar) imagery to support and quickly validate flood inundation models in near real time. A hydraulic model of a 98km reach of the River Po (Italy), previously calibrated on a high-magnitude flood event with extensive and high quality field data, is tested using a SAR flood image, acquired and processed in near real time, during the June 2008 low-magnitude event. Specifically, the image is an acquisition by the ENVISAT-ASAR sensor in wide swath mode and has been provided through ESA (European Space Agency) Fast Registration system at no cost 24 hours after the acquisition. The study shows that the SAR image enables validation and improvement of the model in a time shorter than the flood travel time. This increases the reliability of model predictions (e.g. water elevation and inundation width along the river reach) and, consequently, assists flood management authorities in undertaking the necessary prevention activities.

Maximum Entropy in Drug Discovery

Directory of Open Access Journals (Sweden)

Chih-Yuan Tseng

2014-07-01

Full Text Available Drug discovery applies multidisciplinary approaches either experimentally, computationally or both ways to identify lead compounds to treat various diseases. While conventional approaches have yielded many US Food and Drug Administration (FDA-approved drugs, researchers continue investigating and designing better approaches to increase the success rate in the discovery process. In this article, we provide an overview of the current strategies and point out where and how the method of maximum entropy has been introduced in this area. The maximum entropy principle has its root in thermodynamics, yet since Jaynes’ pioneering work in the 1950s, the maximum entropy principle has not only been used as a physics law, but also as a reasoning tool that allows us to process information in hand with the least bias. Its applicability in various disciplines has been abundantly demonstrated. We give several examples of applications of maximum entropy in different stages of drug discovery. Finally, we discuss a promising new direction in drug discovery that is likely to hinge on the ways of utilizing maximum entropy.

Development of Real-Time System for Urban Flooding by Surcharge of Storm Drainge and River Inundation

Science.gov (United States)

Shim, J. B.; Won, C. Y.; Park, J.; Lee, K.

2017-12-01

Korea experiences frequent flood disasters, which cause considerable economic losses and damages to towns and farms. Especially, a regional torrential storm is about 98.5mm/hr on September 21, 2010 in Seoul. The storm exceeds the capacity of urban drainage system of 75mm/hr, and 9,419 houses. How to monitor and control the urban flood disasters is an important issue in Korea. To mitigate the flood damage, a customizing system was developed to estimate urban floods and inundation using by integrating drainage system data and river information database which are managed by local governments and national agencies. In the case of Korean urban city, there are a lot of detention ponds and drainage pumping stations on end of drainage system and flow is going into river. The drainage pumping station, it is very important hydraulic facility for flood control between river and drainage system. So, it is possible to occur different patterns of flood inundation according to operation rule of drainage pumping station. A flood disaster is different damage as how to operate drainage pumping station and plan operation rule.

Mapping global surface water inundation dynamics using synergistic information from SMAP, AMSR2 and Landsat

Science.gov (United States)

Du, J.; Kimball, J. S.; Galantowicz, J. F.; Kim, S.; Chan, S.; Reichle, R. H.; Jones, L. A.; Watts, J. D.

2017-12-01

A method to monitor global land surface water (fw) inundation dynamics was developed by exploiting the enhanced fw sensitivity of L-band (1.4 GHz) passive microwave observations from the Soil Moisture Active Passive (SMAP) mission. The L-band fw (fwLBand) retrievals were derived using SMAP H-polarization brightness temperature (Tb) observations and predefined L-band reference microwave emissivities for water and land endmembers. Potential soil moisture and vegetation contributions to the microwave signal were represented from overlapping higher frequency Tb observations from AMSR2. The resulting fwLBand global record has high temporal sampling (1-3 days) and 36-km spatial resolution. The fwLBand annual averages corresponded favourably (R=0.84, pretrievals showed favourable classification accuracy for water (commission error 31.84%; omission error 28.08%) and land (commission error 0.82%; omission error 0.99%) and seasonal wet and dry periods when compared to independent water maps derived from Landsat-8 imagery. The new fwLBand algorithms and continuing SMAP and AMSR2 operations provide for near real-time, multi-scale monitoring of global surface water inundation dynamics, potentially benefiting hydrological monitoring, flood assessments, and global climate and carbon modeling.

Use RUSLE2 model to assess the impact of soil erosion on playa inundation and hydrophyte conditions in the Rainwater Basin, Nebraska.

Science.gov (United States)

Tang, Zhenghong; Gu, Yue; Jiang, Weiguo; Xue, Yuan; Bishop, Andy; LaGrange, Ted; Nugent, Eleanor

2016-06-01

Playas in the Rainwater Basin region in Nebraska are globally important wetlands that are continuously threatened by culturally accelerated sedimentation. Using annual habitat survey data and wetland vegetation inventories, inundation and hydrophyte community distributions were evaluated for properties under different types of conservation status. Annual soil erosion rates from surrounding watersheds were calculated to estimate sediment accumulated rates using the Revised Universal Soil Loss Equation 2 (RUSLE2). The slope-length component of the RUSLE2 was derived from 2009 light detection and ranging (LiDAR) data after the methods described by Van Remortel (Computers & Geosciences 30:1043-1053, 2004). Wetlands enrolled in conservation programs were inundated more and were dominated to a greater degree by hydrophytes than wetlands not enrolled in these programs. The mean estimated soil erosion rate at the Rainwater Basin landscape level was 4.67 tons/ha/year, and the mean estimated sediment accumulation depth for public watersheds was estimated as 0.19 cm/year. Without appropriate conservation actions, the current inundated acres and wetland acres growing hydrophytes would be further reduced by sediment accumulation. The results illustrated the importance of conservation programs to protect wetlands.

Tsunami hazard assessment along Diba-Oman and Diba-Al-Emirates coasts

Directory of Open Access Journals (Sweden)

El-Hussain Issa

2017-01-01

Full Text Available Tsunami is among the most devastating natural hazards phenomenon responsible for significant loss of life and property throughout history. The Sultanate of Oman and United Arab Emirates are among the Indian Ocean countries that were subjected to one confirmed tsunami in November 27, 1945 due to an Mw 8.1 earthquake in Makran Subduction Zone. In this study, we present preliminary deterministic tsunami hazard assessment for the coasts of Diba Oman and Diba Al-Emirates, which are located on the western coast of the Oman Sea. The tsunami vulnerability of these cities increases due to the construction of many critical infrastructures and urban concentration along their coasts. Therefore, tsunami hazard assessment is necessary to mitigate the risk on the socio-economic system and sustainable developments. The major known source of tsunamis able to impact both coasts of Oman and United Arab Emirates is the Makran Subduction Zone (MSZ which extends for approximately 900 km. The deterministic approach uses specific scenarios considering the maximum credible earthquakes occurring in the MSZ and computes the ensuing tsunami impact in the coasts of the study area. The maximum wave height graphs and inundation maps are obtained for tsunami scenarios caused by 8.8 earthquake magnitude in eastern MSZ and 8.2 magnitude from western MSZ. The Mw8.8 eastern MSZ causes a maximum inundation distance of 447 meters and a maximum flow depth of 1.37 meter. Maximum inundation distance larger than 420 meters occurs due to the Mw8.2 western MSZ scenario. For this scenario, numerical simulations show a maximum flow depth of about 2.34 meters.

Alteration, slope-classified alteration, and potential lahar inundation maps of volcanoes for the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) Volcano Archive

Science.gov (United States)

Mars, John C.; Hubbard, Bernard E.; Pieri, David; Linick, Justin

2015-01-01

This study identifies areas prone to lahars from hydrothermally altered volcanic edifices on a global scale, using visible and near infrared (VNIR) and short wavelength infrared (SWIR) reflectance data from the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) and digital elevation data from the ASTER Global Digital Elevation Model (GDEM) dataset. This is the first study to create a global database of hydrothermally altered volcanoes showing quantitatively compiled alteration maps and potentially affected drainages, as well as drainage-specific maps illustrating modeled lahars and their potential inundation zones. We (1) identified and prioritized 720 volcanoes based on population density surrounding the volcanoes using the Smithsonian Institution Global Volcanism Program database (GVP) and LandScan™ digital population dataset; (2) validated ASTER hydrothermal alteration mapping techniques using Airborne Visible and Infrared Imaging Spectrometer (AVIRIS) and ASTER data for Mount Shasta, California, and Pico de Orizaba (Citlaltépetl), Mexico; (3) mapped and slope-classified hydrothermal alteration using ASTER VNIR-SWIR reflectance data on 100 of the most densely populated volcanoes; (4) delineated drainages using ASTER GDEM data that show potential flow paths of possible lahars for the 100 mapped volcanoes; (5) produced potential alteration-related lahar inundation maps using the LAHARZ GIS code for Iztaccíhuatl, Mexico, and Mount Hood and Mount Shasta in the United States that illustrate areas likely to be affected based on DEM-derived volume estimates of hydrothermally altered rocks and the ~2x uncertainty factor inherent within a statistically-based lahar model; and (6) saved all image and vector data for 3D and 2D display in Google Earth™, ArcGIS® and other graphics display programs. In addition, these data are available from the ASTER Volcano Archive (AVA) for distribution (available at http://ava.jpl.nasa.gov/recent_alteration_zones.php).

Variability of tsunami inundation footprints considering stochastic scenarios based on a single rupture model: Application to the 2011 Tohoku earthquake

KAUST Repository

Goda, Katsuichiro; Yasuda, Tomohiro; Mori, Nobuhito; Mai, Paul Martin

2015-01-01

distributions. Stochastic tsunami scenarios are generated based on the spectral analysis and synthesis method with regards to an inverted source model. To assess spatial inundation processes accurately, tsunami modeling is conducted using bathymetry

Study of flood defense structural measures priorities using Compromise Programming technique

Science.gov (United States)

Lim, D.; Jeong, S.

2017-12-01

Recent climate change of global warming has led to the frequent occurrence of heavy regional rainfalls. As such, inundation vulnerability increases in urban areas with high population density due to the low runoff carrying capacity. This study selects a sample area (Janghang-eup, the Republic of Korea), which is one of the most vulnerable areas to flooding, analyzing the urban flood runoff model (XP-SWMM) and using the MCDM (Multi-Criteria Decision Making) technique to establish flood protection structural measures. To this end, we compare the alternatives and choose the optimal flood defense measure: our model is utilized with three flood prevention structural measures; (i) drainage pipe construction; (ii) water detention; and (iii) flood pumping station. Dividing the target area into three small basins, we propose flood evaluations for an inundation decrease by studying the flooded area, the maximum inundation depth, the damaged residential area, and the construction cost. In addition, Compromise Programming determines the priority of the alternatives. As a consequent, this study suggests flood pumping station for Zone 1 and drainage pipe construction for Zone 2 and Zone 3, respectively, as the optimal flood defense alternative. Keywords : MCDM; Compromise Programming; Urban Flood Prevention; This research was supported by a grant [MPSS-DP-2013-62] through the Disaster and Safety Management Institute funded by Ministry of Public Safety and Security of Korean government.

The maximum economic depth of groundwater abstraction for irrigation

Science.gov (United States)

Bierkens, M. F.; Van Beek, L. P.; de Graaf, I. E. M.; Gleeson, T. P.

2017-12-01

Over recent decades, groundwater has become increasingly important for agriculture. Irrigation accounts for 40% of the global food production and its importance is expected to grow further in the near future. Already, about 70% of the globally abstracted water is used for irrigation, and nearly half of that is pumped groundwater. In many irrigated areas where groundwater is the primary source of irrigation water, groundwater abstraction is larger than recharge and we see massive groundwater head decline in these areas. An important question then is: to what maximum depth can groundwater be pumped for it to be still economically recoverable? The objective of this study is therefore to create a global map of the maximum depth of economically recoverable groundwater when used for irrigation. The maximum economic depth is the maximum depth at which revenues are still larger than pumping costs or the maximum depth at which initial investments become too large compared to yearly revenues. To this end we set up a simple economic model where costs of well drilling and the energy costs of pumping, which are a function of well depth and static head depth respectively, are compared with the revenues obtained for the irrigated crops. Parameters for the cost sub-model are obtained from several US-based studies and applied to other countries based on GDP/capita as an index of labour costs. The revenue sub-model is based on gross irrigation water demand calculated with a global hydrological and water resources model, areal coverage of crop types from MIRCA2000 and FAO-based statistics on crop yield and market price. We applied our method to irrigated areas in the world overlying productive aquifers. Estimated maximum economic depths range between 50 and 500 m. Most important factors explaining the maximum economic depth are the dominant crop type in the area and whether or not initial investments in well infrastructure are limiting. In subsequent research, our estimates of

Application of the Diminishing Returns Concept in the Hydroecologic Restoration of Riverscapes

International Nuclear Information System (INIS)

Diefenderfer, Heida L.; Johnson, Gary E.; Skalski, John R.; Breithaupt, Stephen A.; Coleman, Andre M.

2012-01-01

Principles for optimizing the number and placement of ecological restoration actions on rivers and coasts would be useful in project engineering design and program planning. This study demonstrated that the yield of inundated floodplain habitat area from dike breaching conforms to a diminishing returns model. The aggregate effects of establishing hydrologic connections between a tidally influenced main stem river and the floodplain were experimentally examined using a hydrodynamic model. Restoration clusters of size 1, 4, 8, and more, replicated and randomized within the landscape, yielded average wetted floodplain area conforming with an exponential rise to maximum curve2(0.99)r=. Analysis of the average incremental change in floodplain inundation produced per breach showed that opening 25 % of the channels crossing the dike provided the maximum return on investment as measured by wetted area. Midstream breaches yielded 60 % and upstream breaches 2 % of the wetted area produced by downstream breaches. Dike-breach restoration programs therefore can be optimized by strategic determination of the spatial configuration and number of demolitions, though biological factors such as the accessibility of floodplain habitat and total length of channels connected also need to be considered. These findings have implications for cost-benefit analyses in restoration program planning.

Minimal length, Friedmann equations and maximum density

Energy Technology Data Exchange (ETDEWEB)

Awad, Adel [Center for Theoretical Physics, British University of Egypt,Sherouk City 11837, P.O. Box 43 (Egypt); Department of Physics, Faculty of Science, Ain Shams University,Cairo, 11566 (Egypt); Ali, Ahmed Farag [Centre for Fundamental Physics, Zewail City of Science and Technology,Sheikh Zayed, 12588, Giza (Egypt); Department of Physics, Faculty of Science, Benha University,Benha, 13518 (Egypt)

2014-06-16

Inspired by Jacobson’s thermodynamic approach, Cai et al. have shown the emergence of Friedmann equations from the first law of thermodynamics. We extend Akbar-Cai derivation http://dx.doi.org/10.1103/PhysRevD.75.084003 of Friedmann equations to accommodate a general entropy-area law. Studying the resulted Friedmann equations using a specific entropy-area law, which is motivated by the generalized uncertainty principle (GUP), reveals the existence of a maximum energy density closed to Planck density. Allowing for a general continuous pressure p(ρ,a) leads to bounded curvature invariants and a general nonsingular evolution. In this case, the maximum energy density is reached in a finite time and there is no cosmological evolution beyond this point which leaves the big bang singularity inaccessible from a spacetime prospective. The existence of maximum energy density and a general nonsingular evolution is independent of the equation of state and the spacial curvature k. As an example we study the evolution of the equation of state p=ωρ through its phase-space diagram to show the existence of a maximum energy which is reachable in a finite time.

Development of Dimensionless Index Assessing Low Impact Development in Urban Areas

Science.gov (United States)

Jun, S. H.; Lee, E. H.; Kim, J. H.

2017-12-01

Because the rapid urbanization and industrialization have increased the impervious area of watersheds, inundation in urban area and water pollution of river by non-point pollutants have caused serious problems for a long time. Low Impact Development (LID) techniques have been implemented for the solution of these problems due to its cost effectiveness for mitigating the water quality and quantity impact on urban areas. There have been many studies about the effectiveness of LID, but there is a lack of research on developing an index for the assessment of LID performance. In this study, the dimensionless reliability index of LID is proposed. The index is developed using Distance Measure Method (DMM). DMM is used to consider the parameters that have different units. The parameters for reliability of LID are the amount of pollutant at the outfall and the flooding volume. Both parameters become dimensionless index by DMM. Weighted factors in dimensionless index are considered to realize the behavior of reliability for the variation of importance to the parameters. LID is applied to an actual area called Gasan city in Seoul, South Korea where inundation is frequently occurred. The reliability is estimated for 16 different rainfall events. For each rainfall event, the parameters with LID installation are compared with those of no LID installation. Depending on which parameter is considered more important, the results showed difference. In conclusion, the optimal locations of LID are suggested as the weighted factors change.

Evaluation of multiple hydraulic models in generating design/near-real time flood inundation extents under various geophysical settings

Science.gov (United States)

Liu, Z.; Rajib, M. A.; Jafarzadegan, K.; Merwade, V.

2015-12-01

Application of land surface/hydrologic models within an operational flood forecasting system can provide probable time of occurrence and magnitude of streamflow at specific locations along a stream. Creating time-varying spatial extent of flood inundation and depth requires the use of a hydraulic or hydrodynamic model. Models differ in representing river geometry and surface roughness which can lead to different output depending on the particular model being used. The result from a single hydraulic model provides just one possible realization of the flood extent without capturing the uncertainty associated with the input or the model parameters. The objective of this study is to compare multiple hydraulic models toward generating ensemble flood inundation extents. Specifically, relative performances of four hydraulic models, including AutoRoute, HEC-RAS, HEC-RAS 2D, and LISFLOOD are evaluated under different geophysical conditions in several locations across the United States. By using streamflow output from the same hydrologic model (SWAT in this case), hydraulic simulations are conducted for three configurations: (i) hindcasting mode by using past observed weather data at daily time scale in which models are being calibrated against USGS streamflow observations, (ii) validation mode using near real-time weather data at sub-daily time scale, and (iii) design mode with extreme streamflow data having specific return periods. Model generated inundation maps for observed flood events both from hindcasting and validation modes are compared with remotely sensed images, whereas the design mode outcomes are compared with corresponding FEMA generated flood hazard maps. The comparisons presented here will give insights on probable model-specific nature of biases and their relative advantages/disadvantages as components of an operational flood forecasting system.

Inundações na Cidade de Lisboa durante o Século XX e os seus factores agraventes

Directory of Open Access Journals (Sweden)

Pedro Elias Oliveira

2002-12-01

Full Text Available INUNDATIONS IN LISBON DURING THE 20TH CENTURY AND THEIR URBANAND PHYSICAL CAUSES. Lisbon often suffers inundations, which must be classified as urban inundations, because the flooded areas involved are impermeable due to urban development. These inundations are not related to the overflow of watercourses, but can be classified as flash inundations because of the speed with which they form and spread. The present study covers a time period from 1918/19 to 1997/98, during which 420 occurrences were recorded in two leading daily newspapers, «O Século» and «Diário de Notícias». The research based on these newspapers takes into account daily rainfalls above 10 l/m2 recorded by the Instituto Geofísico Infante D. Luís, as well as daily rainfall below this level but that have also caused inundations. The analysis of the frequency and evolution of these inundations has showed that they occur more often during the autumn (specially in November and that from the seventies onwards, they have decreased considerably, while at the same time the total rainfall volume has increased, as well as the maximum hourly rainfall that bring them about. Fieldwork was very important in the definition of flooded sites. Research was carried out to specify the physical factors (relief and drainage basins and urban network (squares and streets. The relationship between these urban factors and the old drainage network was also taken into account in order to distinguish increasing inundation factors. Apart from the description of the physical characteristics of these sites, they were also typified through factor analysis. A hazard factor was attributed to each site based on inundation frequency. The most endangered areas and sites are located mainly in the «Frente Ribeirinha» (along the river bank built upon the terminal sectors of the natural watercourses, which consists of the receptor streets and receptor squares of the flow. These streets and squares lie

RISKS INDUCED BY MAXIMUM FLOW WITH 1% PROBABILITY AND THEIR EFFECT ON SEVERAL SPECIES AND HABITATS IN PRICOP-HUTA-CERTEZE AND UPPER TISA NATURA 2000 PROTECTED AREAS

Directory of Open Access Journals (Sweden)

GH. ŞERBAN

2016-03-01

Full Text Available The purpose of the paper is to identify and locate some species related to habitats from Pricop-Huta-Certeze and Upper Tisa Natura 2000 Protected Areas (PHCTS and to determine if they are vulnerable to risks induced by maximum flow phases. In the first chapter are mentioned few references about the morphometric parameters of the hydrographic networks within the study area, as well as some references related to the maximum flow phases frequency. After the second chapter, where methods and databases used in the study are described, we proceed to the identification of the areas that are covered by water during flood, as well as determining the risk level related to these areas. The GIS modeling reveals small extent of the flood high risk for natural environment related to protected areas and greater extent for the anthropic environment. The last chapter refers to several species of fish and batrachia, as well as to those amphibious mammals identified in the study area that are vulnerable to floods (high turbidity effect, reduction of dissolved oxygen quantity, habitats destruction etc..

Influence of the Target Vessel on the Location and Area of Maximum Skin Dose during Percutaneous Coronary Intervention

International Nuclear Information System (INIS)

Chida, K.; Fuda, K.; Kagaya, Y.; Saito, H.; Takai, Y.; Kohzuki, M.; Takahash i, S.; Yamada, S.; Zuguchi, M.

2007-01-01

Background: A number of cases involving radiation-associated patient skin injury attributable to percutaneous coronary intervention (PCI) have been reported. Knowledge of the location and area of the patient's maximum skin dose (MSD) in PCI is necessary to reduce the risk of skin injury. Purpose: To determine the location and area of the MSD in PCI, and separately analyze the effects of different target vessels. Material and Methods: 197 consecutive PCI procedures were studied, and the location and area of the MSD were calculated by a skin-dose mapping software program: Caregraph. The target vessels of the PCI procedures were divided into four groups based on the American Heart Association (AHA) classification. Results: The sites of the MSD for AHA no.1-3, AHA no.4, and AHA no.11-15 were located mainly on the right back skin, the lower right or center back skin, and the upper back skin areas, respectively, whereas the MSD sites for the AHA no. 5-10 PCI were widely spread. The MSD area for the AHA no. 4 PCI was larger than that for the AHA no. 11-15 PCI (P<0.0001). Conclusion: Although the radiation associated with PCI can be widely spread and variable, we observed a tendency regarding the location and area of the MSD when we separately analyzed the data for different target vessels. We recommend the use of a smaller radiation field size and the elimination of overlapping fields during PCI

Mapping Dynamics of Inundation Patterns of Two Largest River-Connected Lakes in China: A Comparative Study

OpenAIRE

Guiping Wu; Yuanbo Liu

2016-01-01

Poyang Lake and Dongting Lake are the two largest freshwater lakes in China. The lakes are located approximately 300 km apart on the middle reaches of the Yangtze River and are differently connected through their respective tributary systems, which will lead to different river–lake water exchanges and discharges. Thus, differences in their morphological and hydrological conditions should induce individual lake spatio-temporal inundation patterns. Quantitative comparative analyses of the dynam...

Monitoring flooding and vegetation on seasonally inundated floodplains with multifrequency polarimetric synthetic aperture radar

Science.gov (United States)

Hess, Laura Lorraine

The ability of synthetic aperture radar to detect flooding and vegetation structure was evaluated for three seasonally inundated floodplain sites supporting a broad variety of wetland and upland vegetation types: two reaches of the Solimoes floodplain in the central Amazon, and the Magela Creek floodplain in Northern Territory, Australia. For each site, C- and L-band polarimetric Shuttle Imaging Radar-C (SIR-C) data was obtained at both high- and low-water stages. Inundation status and vegetation structure were documented simultaneous with the SIR-C acquisitions using low-altitude videography and ground measurements. SIR-C images were classified into cover states defined by vegetation physiognomy and presence of standing water, using a decision-tree model with backscattering coefficients at HH, VV, and HV polarizations as input variables. Classification accuracy was assessed using user's accuracy, producer's accuracy, and kappa coefficient for a test population of pixels. At all sites, both C- and L-band were necessary to accurately classify cover types with two dates. HH polarization was most. useful for distinguishing flooded from non-flooded vegetation (C-HH for macrophyte versus pasture, L-HH for flooded versus non-flooded forest), and cross-polarized L-band data provided the best separation between woody and non-woody vegetation. Increases in L-HH backscattering due to flooding were on the order of 3--4 dB for closed-canopy varzea and igapo forest, and 4--7 dB, for open Melaleuca woodland. The broad range of physiognomies and stand structures found in both herbaceous and woody wetland communities, combined with the variation in the amount of emergent canopy caused by water level fluctuations and phenologic changes, resulted in a large range in backscattering characteristics of wetland communities both within and between sites. High accuracies cannot be achieved for these communities using single-date, single-band, single-polarization data, particularly in the

Near Field Modeling for the Maule Tsunami from DART, GPS and Finite Fault Solutions (Invited)

Science.gov (United States)

Arcas, D.; Chamberlin, C.; Lagos, M.; Ramirez-Herrera, M.; Tang, L.; Wei, Y.

2010-12-01

The earthquake and tsunami of February, 27, 2010 in central Chile has rekindled an interest in developing techniques to predict the impact of near field tsunamis along the Chilean coastline. Following the earthquake, several initiatives were proposed to increase the density of seismic, pressure and motion sensors along the South American trench, in order to provide field data that could be used to estimate tsunami impact on the coast. However, the precise use of those data in the elaboration of a quantitative assessment of coastal tsunami damage has not been clarified. The present work makes use of seismic, Deep-ocean Assessment and Reporting of Tsunamis (DART®) systems, and GPS measurements obtained during the Maule earthquake to initiate a number of tsunami inundation models along the rupture area by expressing different versions of the seismic crustal deformation in terms of NOAA’s tsunami unit source functions. Translation of all available real-time data into a feasible tsunami source is essential in near-field tsunami impact prediction in which an impact assessment must be generated under very stringent time constraints. Inundation results from each different source are then contrasted with field and tide gauge data by comparing arrival time, maximum wave height, maximum inundation and tsunami decay rate, using field data collected by the authors.

Assessing the impacts of climate change and dams on floodplain inundation and wetland connectivity in the wet-dry tropics of northern Australia

Science.gov (United States)

Karim, Fazlul; Dutta, Dushmanta; Marvanek, Steve; Petheram, Cuan; Ticehurst, Catherine; Lerat, Julien; Kim, Shaun; Yang, Ang

2015-03-01

Floodplain wetlands and their hydrological connectivity with main river channels in the Australian wet-dry tropics are under increasing pressure from global climate change and water resource development, and there is a need for modelling tools to estimate the time dynamics of connectivity. This paper describes an integrated modelling framework combining conceptual rainfall-runoff modelling, river system modelling and hydrodynamic (HD) modelling to estimate hydrological connectivity between wetlands and rivers in the Flinders and Gilbert river catchments in northern Australia. Three historical flood events ranging from a mean annual flood to a 35-year return period flood were investigated using a two dimensional HD model (MIKE 21). Inflows from upstream catchments were estimated using a river network model. Local runoff within the HD modelling domain was simulated using the Sacramento rainfall-runoff model. The Shuttle Radar Topography Mission (SRTM) derived 30 m DEM was used to reproduce floodplain topography, stream networks and wetlands in the HD model. The HD model was calibrated using stream gauge data and inundation maps derived from satellite (MODIS: MODerate resolution Imaging Spectroradiometer) imagery. An algorithm was developed to combine the simulated water heights with the DEM to quantify inundation and flow connection between wetlands and rivers. The connectivity of 18 ecologically important wetlands on the Flinders floodplain and 7 on the Gilbert floodplain were quantified. The impacts of climate change and water resource development on connectivity to individual wetlands were assessed under a projected dry climate (2nd driest of 15 GCMs), wet climate (2nd wettest of 15 GCMs) and dam conditions. The results indicate that changes in rainfall under a wetter and drier future climate could have large impacts on area, duration and frequency of inundation and connectivity. Topographic relief, river bank elevation and flood magnitude were found to be the key

Development of Inundation Map for Hypothetical Asa Dam Break using HEC-RAS and ARC GIS

Directory of Open Access Journals (Sweden)

O. S. Balogun

2017-12-01

Full Text Available Asa Dam in Ilorin, Nigeria was constructed in the1980s. The dam made of earth material has a length of 507 meters and height of 27 meters. The maximum capacity of the impoundment during the raining season is approximately 43 x 106 m3. Years after construction, tremendous physical development is taking place along the river channel starting from the dam axis towards downstream for a distance of approximately 12 km. It is estimated that several thousands of people are currently living and performing various activities within the vicinity of the river channel. It is therefore necessary to evaluate the risk involved in case of a possible dam break disaster. In view of this, a hypothetical dam break scenario was studied and analyzed using Hydrologic Engineering Center’s River Analysis System computer model. Unsteady flow simulation was performed using geometric data obtained from Digital Terrain Model with 100-year, 24 hr flow event. The HEC-RAS was used in concert with HEC-GeoRAS to assess the flood hazard along the approximately 12 km river channel. The simulated water surface elevations were exported to Arc GIS to produce an inundation map that graphically indicates the extent of the flood hazard. The results show that some important locations such as industrial, residential, motor parks, recreational and places of worship along the river length are prone to significant flood impact. This map serves as an input for emergency preparation programme in the event of the dam break.

Douglas County Dam Breach Inundation Areas

Data.gov (United States)

Kansas Data Access and Support Center — Dam breach analysis provides a prediction of the extent and timing of flooding from a catastrophic breach of the dams. These results are sufficient for developing...

Coastal flooding hazard related to storms and coastal evolution in Valdelagrana spit (Cadiz Bay Natural Park, SW Spain)

Science.gov (United States)

Benavente, J.; Del Río, L.; Gracia, F. J.; Martínez-del-Pozo, J. A.

2006-06-01

Mapping of coastal inundation hazard related to storms requires the combination of multiple sources of information regarding meteorological, morphological and dynamic characteristics of both the area at risk and the studied phenomena. Variables such as beach slope, storm wave height or wind speed have traditionally been used, but detailed geomorphological features of the area as well as long-term shoreline evolution trends must also be taken into account in order to achieve more realistic results. This work presents an evaluation of storm flooding hazard in Valdelagrana spit and marshes (SW Spain), considering two types of storm that are characteristic of the area: a modal storm with 1 year of recurrence interval (maximum wave height of 3.3 m), and an extreme storm with 6-10 years of recurrence interval (maximum wave height of 10.6 m), both approaching the coast perpendicularly. After calculating theoretical storm surge elevation, a digital terrain model was made by adjusting topographic data to field work and detailed geomorphological analysis. A model of flooding extent was subsequently developed for each storm type, and then corrected according to the rates of shoreline change in the last decades, which were assessed by means of aerial photographs taking the dune toe as shoreline indicator. Results show that long-term coastline trend represents an important factor in the prediction of flooding extent, since shoreline retreat causes the deterioration of natural coastal defences as dune ridges, thus increasing coastal exposure to high-energy waves. This way, it has been stated that the lack of sedimentary supply plays an important role in spatial variability of inundation extent in Valdelagrana spit. Finally, a hazard map is presented, where calculated coastal retreat rates are employed in order to predict the areas that could be affected by future inundation events.

Flow paths of water and sediment in a tidal marsh: relations with marsh developmental stage and tidal inundation height

NARCIS (Netherlands)

Temmerman, S.; Bouma, T.J.; Govers, G.; Lauwaet, D.

2005-01-01

This study provides new insights in the relative role of tidal creeks and the marsh edge in supplying water and sediments to and from tidal marshes for a wide range of tidal inundation cycles with different high water levels and for marsh zones of different developmental stage. Net import or export

Kaitan antara karakteristik pantai Provinsi Sumatera Barat dengan potensi kerawanan tsunami

Directory of Open Access Journals (Sweden)

Yudhicara Yudhicara

2014-06-01

Full Text Available http://dx.doi.org/10.17014/ijog.vol3no2.20084The coast of West Sumatera Province has two types of beaches: low lying sandy beach and steep rocky beach. Straight shoreline beaches at Padang beach until Air Bangis at the north and between Pasir Ganting and Salido beach at the south will have a potential tsunami height lower than bay shape beaches like at Kasai Bay, Kabung Bay, Batung Bay and Nibung Bay. A tsunami inundation will be further at a low lying area (low lying sandy beaches compared with a coastal area which has steep slope and high relief (steep rocky beaches. Gosong beach at Pariaman which has a steep angle of beach slope will have lower tsunami height compared with a low angle beach slope like at Sungai Beramas, Kasai, Kabung, Batung and Nibung bays which have a beach slope about 3° to 5°. The maximum tsunami inundation is assumed to be located at Pasaman and Pasir Pariaman Sub-regencies, while the maximum tsunami height is assumed to be located at the middle of mapped area which has a bay shape. Tsunami is assumed to be arrived early at the southern most of mapped area or close to Muko-muko (Bengkulu. The maximum height difference from sea level was found at Tabai - Pariaman about 5.394 m, while the minimum height difference was found at Carocok Anau about 1.821 m. The horizontal distance measured from the nearest building from the shoreline is about 119 to 173 m. The worst case of tsunami modeling assumed that the maximum tsunami height will be about 32 m and used for reference to make tsunami prone zonation, such as high, moderate and low prone area.    

Sea, Lake, and Overland Surge from Hurricanes (SLOSH) Inundation for Categories 2 and 4

Science.gov (United States)

The file geodatabase (fgdb) contains the Sea, Lake, and Overland Surge from Hurricanes (SLOSH) Maximum of Maximums (MOM) model for hurricane categories 2 and 4. The EPA Office of Research & Development (ORD) modified the original model from NOAA to fit the model parameters for the Buzzards Bay region. The models show storm surge extent for the Mattapoisett area and therefore the flooding area was reduced to the study area. Areas of flooding that were not connected to the main water body were removed. The files in the geodatabase are:Cat2_SLR0_Int_Feet_dissolve_Mattapoisett: Current Category 2 hurricane with 0 ft sea level riseCat4_SLR0_Int_Feet_dissolve_Mattapoisett: Current Category 4 hurricane with 0 ft sea level riseCat4_SLR4_Int_Feet_dissolve_Mattapoisett: Future Category 4 hurricane with 4 feet sea level riseThe features support the Weather Ready Mattapoisett story map, which can be accessed via the following link:https://epa.maps.arcgis.com/apps/MapJournal/index.html?appid=1ff4f1d28a254cb689334799d94b74e2

Probable maximum flood control

International Nuclear Information System (INIS)

DeGabriele, C.E.; Wu, C.L.

1991-11-01

This study proposes preliminary design concepts to protect the waste-handling facilities and all shaft and ramp entries to the underground from the probable maximum flood (PMF) in the current design configuration for the proposed Nevada Nuclear Waste Storage Investigation (NNWSI) repository protection provisions were furnished by the United States Bureau of Reclamation (USSR) or developed from USSR data. Proposed flood protection provisions include site grading, drainage channels, and diversion dikes. Figures are provided to show these proposed flood protection provisions at each area investigated. These areas are the central surface facilities (including the waste-handling building and waste treatment building), tuff ramp portal, waste ramp portal, men-and-materials shaft, emplacement exhaust shaft, and exploratory shafts facility

High resolution tsunami modelling for the evaluation of potential risk areas in Setúbal (Portugal

Directory of Open Access Journals (Sweden)

J. Ribeiro

2011-08-01

Full Text Available The use of high resolution hydrodynamic modelling to simulate the potential effects of tsunami events can provide relevant information about the most probable inundation areas. Moreover, the consideration of complementary data such as the type of buildings, location of priority equipment, type of roads, enables mapping of the most vulnerable zones, computing of the expected damage on man-made structures, constrain of the definition of rescue areas and escape routes, adaptation of emergency plans and proper evaluation of the vulnerability associated with different areas and/or equipment.

Such an approach was used to evaluate the specific risks associated with a potential occurrence of a tsunami event in the region of Setúbal (Portugal, which was one of the areas most seriously affected by the 1755 tsunami.

In order to perform an evaluation of the hazard associated with the occurrence of a similar event, high resolution wave propagation simulations were performed considering different potential earthquake sources with different magnitudes. Based on these simulations, detailed inundation maps associated with the different events were produced. These results were combined with the available information on the vulnerability of the local infrastructures (building types, roads and streets characteristics, priority buildings in order to impose restrictions in the production of high-scale potential damage maps, escape routes and emergency routes maps.

Tsunami vulnerability and damage assessment in the coastal area of Rabat and Salé, Morocco

Directory of Open Access Journals (Sweden)

A. Atillah

2011-12-01

Full Text Available This study, a companion paper to Renou et al. (2011, focuses on the application of a GIS-based method to assess building vulnerability and damage in the event of a tsunami affecting the coastal area of Rabat and Salé, Morocco. This approach, designed within the framework of the European SCHEMA project (www.schemaproject.org is based on the combination of hazard results from numerical modelling of the worst case tsunami scenario (inundation depth based on the historical Lisbon earthquake of 1755 and the Portugal earthquake of 1969, together with vulnerability building types derived from Earth Observation data, field surveys and GIS data. The risk is then evaluated for this highly concentrated population area characterized by the implementation of a vast project of residential and touristic buildings within the flat area of the Bouregreg Valley separating the cities of Rabat and Salé. A GIS tool is used to derive building damage maps by crossing layers of inundation levels and building vulnerability. The inferred damage maps serve as a base for elaborating evacuation plans with appropriate rescue and relief processes and to prepare and consider appropriate measures to prevent the induced tsunami risk.

History of natural resource use and environmental impacts in an interfluvial upland forest area in western Amazonia

OpenAIRE

Anders Siren

2014-01-01

Much of the research done on environmental impacts by Amazonian indigenous peoples in the past focus on certain areas where archaeological remains are particularly abundant, such as the Amazon River estuary, the seasonally inundated floodplain of the lower Amazon, and various sites in the forest-savannah mosaic of the southern Amazon The environmental history of interfluvial upland areas has received less attention. This study reconstructed the history of human use of natural resources in an ...

Estimating Error in SRTM Derived Planform of a River in Data-poor Region and Subsequent Impact on Inundation Modeling

Science.gov (United States)

Bhuyian, M. N. M.; Kalyanapu, A. J.

2017-12-01

Accurate representation of river planform is critical for hydrodynamic modeling. Digital elevation models (DEM) often falls short in accurately representing river planform because they show the ground as it was during data acquisition. But, water bodies (i.e. rivers) change their size and shape over time. River planforms are more dynamic in undisturbed riverine systems (mostly located in data-poor regions) where remote sensing is the most convenient source of data. For many of such regions, Shuttle Radar Topographic Mission (SRTM) is the best available source of DEM. Therefore, the objective of this study is to estimate the error in SRTM derived planform of a river in a data-poor region and estimate the subsequent impact on inundation modeling. Analysis of Landsat image, SRTM DEM and remotely sensed soil data was used to classify the planform activity in an 185 km stretch of the Kushiyara River in Bangladesh. In last 15 years, the river eroded about 4.65 square km and deposited 7.55 square km area. Therefore, current (the year 2017) river planform is significantly different than the SRTM water body data which represents the time of SRTM data acquisition (the year 2000). The rate of planform shifting significantly increased as the river traveled to downstream. Therefore, the study area was divided into three reaches (R1, R2, and R3) from upstream to downstream. Channel slope and meandering ratio changed from 2x10-7 and 1.64 in R1 to 1x10-4 and 1.45 in R3. However, more than 60% erosion-deposition occurred in R3 where a high percentage of Fluvisols (98%) and coarse particles (21%) were present in the vicinity of the river. It indicates errors in SRTM water body data (due to planform shifting) could be correlated with the physical properties (i.e. slope, soil type, meandering ratio etc.) of the riverine system. The correlations would help in zoning activity of a riverine system and determine a timeline to update DEM for a given region. Additionally, to estimate the

Tsunami hazard assessment in the Hudson River Estuary based on dynamic tsunami-tide simulations

Science.gov (United States)

Shelby, Michael; Grilli, Stéphan T.; Grilli, Annette R.

2016-12-01

This work is part of a tsunami inundation mapping activity carried out along the US East Coast since 2010, under the auspice of the National Tsunami Hazard Mitigation program (NTHMP). The US East Coast features two main estuaries with significant tidal forcing, which are bordered by numerous critical facilities (power plants, major harbors,...) as well as densely built low-level areas: Chesapeake Bay and the Hudson River Estuary (HRE). HRE is the object of this work, with specific focus on assessing tsunami hazard in Manhattan, the Hudson and East River areas. In the NTHMP work, inundation maps are computed as envelopes of maximum surface elevation along the coast and inland, by simulating the impact of selected probable maximum tsunamis (PMT) in the Atlantic ocean margin and basin. At present, such simulations assume a static reference level near shore equal to the local mean high water (MHW) level. Here, instead we simulate maximum inundation in the HRE resulting from dynamic interactions between the incident PMTs and a tide, which is calibrated to achieve MHW at its maximum level. To identify conditions leading to maximum tsunami inundation, each PMT is simulated for four different phases of the tide and results are compared to those obtained for a static reference level. We first separately simulate the tide and the three PMTs that were found to be most significant for the HRE. These are caused by: (1) a flank collapse of the Cumbre Vieja Volcano (CVV) in the Canary Islands (with a 80 km3 volume representing the most likely extreme scenario); (2) an M9 coseismic source in the Puerto Rico Trench (PRT); and (3) a large submarine mass failure (SMF) in the Hudson River canyon of parameters similar to the 165 km3 historical Currituck slide, which is used as a local proxy for the maximum possible SMF. Simulations are performed with the nonlinear and dispersive long wave model FUNWAVE-TVD, in a series of nested grids of increasing resolution towards the coast, by one

Spatio-Temporal Analysis of Vegetation Dynamics in Relation to Shifting Inundation and Fire Regimes: Disentangling Environmental Variability from Land Management Decisions in a Southern African Transboundary Watershed

Directory of Open Access Journals (Sweden)

Narcisa G. Pricope

2015-07-01

Full Text Available Increasing temperatures and wildfire incidence and decreasing precipitation and river runoff in southern Africa are predicted to have a variety of impacts on the ecology, structure, and function of semi-arid savannas, which provide innumerable livelihood resources for millions of people. This paper builds on previous research that documents change in inundation and fire regimes in the Chobe River Basin (CRB in Namibia and Botswana and proposes to demonstrate a methodology that can be applied to disentangle the effect of environmental variability from land management decisions on changing and ecologically sensitive savanna ecosystems in transboundary contexts. We characterized the temporal dynamics (1985–2010 of vegetation productivity for the CRB using proxies of vegetation productivity and examine the relative importance of shifts in flooding and fire patterns to vegetation dynamics and effects of the association of phases of the El Niño—Southern Oscillation (ENSO on vegetation greenness. Our results indicate that vegetation in these semi-arid environments is highly responsive to climatic fluctuations and the long-term trend is one of increased but heterogeneous vegetation cover. The increased cover and heterogeneity during the growing season is especially noted in communally-managed areas of Botswana where long-term fire suppression has been instituted, in contrast to communal areas in Namibia where heterogeneity in vegetation cover is mostly increasing primarily outside of the growing season and may correspond to mosaic early dry season burns. Observed patterns of increased vegetation productivity and heterogeneity may relate to more frequent and intense burning and higher spatial variability in surface water availability from both precipitation and regional inundation patterns, with implications for global environmental change and adaptation in subsistence-based communities.

Tropical Cyclone Storm Surge Inundation and Velocity Hazard Mapping of the State of Andhra Pradesh (India) using ADCIRC

Science.gov (United States)

Brackins, J. T.; Kalyanapu, A. J.

2017-12-01

The Northern Indian Ocean Bay of Bengal region, including parts of India, Bangladesh, Myanmar, and Sri Lanka, is the largest bay in the world and is structured in such a manner as to produce the world's largest tropical cyclone (TC) storm surges (SS), with approximately five surge events greater than 5 meters in magnitude each decade. (Needham et al. 2015). Although some studies have been performed to attempt to capture the magnitude and location of historical surges (Shaji et al. 2014) and to model surges in the immediate sense, there is a notable lack of application to the effects on coastal infrastructure in these areas. Given that these areas are some of the most densely populated and least economically able to prepare and recover, it is important to consider the potential effects of storm surge to discover areas where improvements can be made with the limited resources available to these areas. To this end, an ADvanced-CIRCulation (ADCIRC) model (Luettich and Westerink 2004) was created for the Bay of Bengal, using the General Bathymetric Chart of the Oceans (GEBCO 2014) as bathymetric and topographic data, and a combination of the Joint Typhoon Warning Center (JTWC) and India Meteorological Department (IMD) records for storm tracks. For the state of Andhra Pradesh, several major TC events ranging from 1977 to 2014 were selected to be modeled with the goal of creating hazard maps of storm surge inundation and velocity for the state. These hazard maps would be used to identify high-vulnerability areas with the goal of implementing land-use planning and coastal development practices that will aid in ameliorating both the loss of life and economic damages sustained as a result of these TCs.

Potential impact of predicted sea level rise on carbon sink function of mangrove ecosystems with special reference to Negombo estuary, Sri Lanka

Science.gov (United States)

Perera, K. A. R. S.; De Silva, K. H. W. L.; Amarasinghe, M. D.

2018-02-01

Unique location in the land-sea interface makes mangrove ecosystems most vulnerable to the impacts of predicted sea level rise due to increasing anthropogenic CO2 emissions. Among others, carbon sink function of these tropical ecosystems that contribute to reduce rising atmospheric CO2 and temperature, could potentially be affected most. Present study was undertaken to explore the extent of impact of the predicted sea level rise for the region on total organic carbon (TOC) pools of the mangrove ecosystems in Negombo estuary located on the west coast of Sri Lanka. Extents of the coastal inundations under minimum (0.09 m) and maximum (0.88 m) sea level rise scenarios of IPCC for 2100 and an intermediate level of 0.48 m were determined with GIS tools. Estimated total capacity of organic carbon retention by these mangrove areas was 499.45 Mg C ha- 1 of which 84% (418.98 Mg C ha- 1) sequestered in the mangrove soil and 16% (80.56 Mg C ha- 1) in the vegetation. Total extent of land area potentially affected by inundation under lowest sea level rise scenario was 218.9 ha, while it was 476.2 ha under intermediate rise and 696.0 ha with the predicted maximum sea level rise. Estimated rate of loss of carbon sink function due to inundation by the sea level rise of 0.09 m is 6.30 Mg C ha- 1 y- 1 while the intermediate sea level rise indicated a loss of 9.92 Mg C ha- 1 y- 1 and under maximum sea level rise scenario, this loss further increases up to 11.32 Mg C ha- 1 y- 1. Adaptation of mangrove plants to withstand inundation and landward migration along with escalated photosynthetic rates, augmented by changing rainfall patterns and availability of nutrients may contribute to reduce the rate of loss of carbon sink function of these mangrove ecosystems. Predictions over change in carbon sequestration function of mangroves in Negombo estuary reveals that it is not only affected by oceanographic and hydrological alterations associated with sea level rise but also by anthropogenic

CLUJ-NAPOCA PRECIPITATION FORECAST USING WSR-98D DOPPLER RADAR

Directory of Open Access Journals (Sweden)

Narcis MAIER

2011-11-01

Full Text Available CLUJ-NAPOCA precipitation forecast using WSR-98D Doppler radar. Forecasting inundations requires accurate spatial and temporal estimation of rainfalls in an area. Depending on the Z-R relationship (reflectivity-precipitation rate, the thresholds, maximum reflectivity data processing, VIL, cloud height or speed, provided by the WSR-98D affects the estimated precipitation used in the prediction of inundations. How much precipitation receives a watershed during an extreme event and what response will result depends on the basin hydrographic characteristics. A study of summer weather events between the years 2004-2008 and a new method in establishing relations between the radar estimated and recorded precipitations led to the determination of new relations between them which will balance the connections between them.

2004 INDIAN OCEAN TSUNAMI ON THE MALDIVES ISLANDS: INITIAL OBSERVATIONS

Directory of Open Access Journals (Sweden)

Barbara H. Keating

2005-01-01

Full Text Available Post-tsunami field surveys of the Maldives Islands where carried out to document the effects of the tsunami inundation. The study area was situated in the islands of South Male Atoll that were some of the most heavily damaged islands of the Maldive Islands. The tsunami damaged the natural environment, vegetation, man-made structures, and residents. The maximum tsunami wave height was 3-4 m. This level of inundation exceeded the height of most residents. The wave height was greatest on the eastern rim of the South Male Atoll (closest to the tsunami source and these islands were completely flooded. The islands within the interior of the atoll saw the lowest wave heights, and these were only marginally flooded.Surveys of flood lines left on the exterior and interior of structures were measured but proved to be substantially less than that reported by survivors. It appears that the highest inundation was not preserved as flood lines. We suggest that the turbulence associated with the tsunami inundation erased the highest lines or that they did not form due to an absence of debris and organic compounds that acted as adhesion during the initial flooding.Significant erosion was documented. Deposition took place in the form of sand sheets while only desultory deposition of coral clasts in marginal areas was found. Seasonal erosion, and storms are likely to remove most or all of the traces of the tsunami within these islands.

MAXIMUM PRINCIPLE FOR SUBSONIC FLOW WITH VARIABLE ENTROPY

Directory of Open Access Journals (Sweden)

B. Sizykh Grigory

2017-01-01

Full Text Available Maximum principle for subsonic flow is fair for stationary irrotational subsonic gas flows. According to this prin- ciple, if the value of the velocity is not constant everywhere, then its maximum is achieved on the boundary and only on the boundary of the considered domain. This property is used when designing form of an aircraft with a maximum critical val- ue of the Mach number: it is believed that if the local Mach number is less than unit in the incoming flow and on the body surface, then the Mach number is less then unit in all points of flow. The known proof of maximum principle for subsonic flow is based on the assumption that in the whole considered area of the flow the pressure is a function of density. For the ideal and perfect gas (the role of diffusion is negligible, and the Mendeleev-Clapeyron law is fulfilled, the pressure is a function of density if entropy is constant in the entire considered area of the flow. Shows an example of a stationary sub- sonic irrotational flow, in which the entropy has different values on different stream lines, and the pressure is not a function of density. The application of the maximum principle for subsonic flow with respect to such a flow would be unreasonable. This example shows the relevance of the question about the place of the points of maximum value of the velocity, if the entropy is not a constant. To clarify the regularities of the location of these points, was performed the analysis of the com- plete Euler equations (without any simplifying assumptions in 3-D case. The new proof of the maximum principle for sub- sonic flow was proposed. This proof does not rely on the assumption that the pressure is a function of density. Thus, it is shown that the maximum principle for subsonic flow is true for stationary subsonic irrotational flows of ideal perfect gas with variable entropy.

Evaluation of the Benefit of Flood Reduction by Artificial Groundwater Recharge Lake Operation in a Coastal Area

Science.gov (United States)

Chen, Ching-Nuo; Tsai, Chih-Heng

2017-04-01

Inundation disasters often occur in the southwestern coastal plains of Taiwan. The coastal plains suffers mostly from land-subsidence, surface water is difficult to be drained during the typhoon period, leading to more severe flood disasters. Global climate warming has become more significant, which in turn has resulted in the increase in amplitude and frequency of climate change related disasters. In addition, climate change also induces a rise in sea water level year by year. The rise in sea water level does not only weakens the function of existing drainage system but also increases tidal levels and storm tide levels, which increases the probability and amount of inundation disasters. The serious land subsidence area at Linbian river basin was selected as the study area. An artificial groundwater recharge lake has been set up in Linbian river basin by Pingtung government. The development area of this lake is 58 hectare and the storage volume is 2.1 million cubic meters (210 × 104m3). The surface water from Linbian basin during a wet season is led into the artificial groundwater recharge lake by water diversion project, and then employ special hydro-geological conditions of the area for groundwater recharge, increase groundwater supply and decrease land subsidence rate, and incidentally some of the flood diversion, detention, reduce flooding. In this study, a Real-time Interactive Inundation Model is applied to simulate different flooding storage volume and gate operations to estimate the benefits of flood mitigation. According to the simulation results, the hydrograph shape, peak-flow reduction and time lag to peak of the flood reduction hydrograph into the lake are apparently different for each case of different gate operation at the same storage volume. Therefore, the effect of flood control and disaster mitigation is different. The flood control and disaster mitigation benefits are evaluated by different operation modes, which provide decision makers to

Potential for timing high-energy marine inundation events in the recent geological past through age-dating of reef boulders in Fiji

Science.gov (United States)

Terry, James P.; Etienne, Samuel

2014-12-01

Transported coastal boulders have increasingly come to represent a valuable element of investigations within the broader framework of multi-proxy approaches applied to coastal hazard studies. Through a case study on Taveuni Island in Fiji, this paper outlines some approaches and hindrances to effective timing of prehistorical high-energy marine inundation events (storms and tsunamis) on tropical coastlines from the evidence of reef-platform carbonate boulders. Various sources of errors are outlined that investigators must consider when attempting to use carbonate boulder ages as a surrogate for timing past events. On Taveuni, uranium : thorium dates with a high level of precision (1-7 years) suggest that major inundation events have a return period of approximately 40-45 years since 1650 AD. Of particular importance, considerably different age dates are provided by coral samples sourced from the top and bottom (i.e. opposite faces) of individual boulders, so highlighting interpretation biases that must be avoided.

Dengue fever Potential Area at Pademangan Barat Sub District, North Jakarta

Directory of Open Access Journals (Sweden)

Tri E. B. Soesilo

2011-06-01

Full Text Available Dengue hemorrhagic fever is an infectious disease that contagious by Aedes aegypti mosquito’s bites. Anybody could infectious by this illness, without differentiate their sex, age, social status, and economic status as well. Nevertheless, at slum area, where mosquito’s larva is easy to find, the number of infectious people is presuming high. By using primary data and analyze with geography information system (GIS, the study found that the number of infectious people of dengue fever do not have any positive correlation with larva amount, that was monitored through clean water in the surrounding neighborhood area. The number of infectious people have correlation with the dirty areas that caused by the piling of used articles and inundate area. Gender and age do not have any influence with the number of infectious people.

Identification of Watershed-scale Critical Source Areas Using Bayesian Maximum Entropy Spatiotemporal Analysis

Science.gov (United States)

Roostaee, M.; Deng, Z.

2017-12-01

The states' environmental agencies are required by The Clean Water Act to assess all waterbodies and evaluate potential sources of impairments. Spatial and temporal distributions of water quality parameters are critical in identifying Critical Source Areas (CSAs). However, due to limitations in monetary resources and a large number of waterbodies, available monitoring stations are typically sparse with intermittent periods of data collection. Hence, scarcity of water quality data is a major obstacle in addressing sources of pollution through management strategies. In this study spatiotemporal Bayesian Maximum Entropy method (BME) is employed to model the inherent temporal and spatial variability of measured water quality indicators such as Dissolved Oxygen (DO) concentration for Turkey Creek Watershed. Turkey Creek is located in northern Louisiana and has been listed in 303(d) list for DO impairment since 2014 in Louisiana Water Quality Inventory Reports due to agricultural practices. BME method is proved to provide more accurate estimates than the methods of purely spatial analysis by incorporating space/time distribution and uncertainty in available measured soft and hard data. This model would be used to estimate DO concentration at unmonitored locations and times and subsequently identifying CSAs. The USDA's crop-specific land cover data layers of the watershed were then used to determine those practices/changes that led to low DO concentration in identified CSAs. Primary results revealed that cultivation of corn and soybean as well as urban runoff are main contributing sources in low dissolved oxygen in Turkey Creek Watershed.

Calibration of HEC-Ras hydrodynamic model using gauged discharge data and flood inundation maps

Science.gov (United States)

Tong, Rui; Komma, Jürgen

2017-04-01

The estimation of flood is essential for disaster alleviation. Hydrodynamic models are implemented to predict the occurrence and variance of flood in different scales. In practice, the calibration of hydrodynamic models aims to search the best possible parameters for the representation the natural flow resistance. Recent years have seen the calibration of hydrodynamic models being more actual and faster following the advance of earth observation products and computer based optimization techniques. In this study, the Hydrologic Engineering River Analysis System (HEC-Ras) model was set up with high-resolution digital elevation model from Laser scanner for the river Inn in Tyrol, Austria. 10 largest flood events from 19 hourly discharge gauges and flood inundation maps were selected to calibrate the HEC-Ras model. Manning roughness values and lateral inflow factors as parameters were automatically optimized with the Shuffled complex with Principal component analysis (SP-UCI) algorithm developed from the Shuffled Complex Evolution (SCE-UA). Different objective functions (Nash-Sutcliffe model efficiency coefficient, the timing of peak, peak value and Root-mean-square deviation) were used in single or multiple way. It was found that the lateral inflow factor was the most sensitive parameter. SP-UCI algorithm could avoid the local optimal and achieve efficient and effective parameters in the calibration of HEC-Ras model using flood extension images. As results showed, calibration by means of gauged discharge data and flood inundation maps, together with objective function of Nash-Sutcliffe model efficiency coefficient, was very robust to obtain more reliable flood simulation, and also to catch up with the peak value and the timing of peak.

Two-dimensional simulation of the June 11, 2010, flood of the Little Missouri River at Albert Pike Recreational Area, Ouachita National Forest, Arkansas

Science.gov (United States)

Wagner, Daniel M.

2013-01-01

In the early morning hours of June 11, 2010, substantial flooding occurred at Albert Pike Recreation Area in the Ouachita National Forest of west-central Arkansas, killing 20 campers. The U.S. Forest Service needed information concerning the extent and depth of flood inundation, the water velocity, and flow paths throughout Albert Pike Recreation Area for the flood and for streamflows corresponding to annual exceedence probabilities of 1 and 2 percent. The two-dimensional flow model Fst2DH, part of the Federal Highway Administration’s Finite Element Surface-water Modeling System, and the graphical user interface Surface-water Modeling System (SMS) were used to perform a steady-state simulation of the flood in a 1.5-mile reach of the Little Missouri River at Albert Pike Recreation Area. Peak streamflows of the Little Missouri River and tributary Brier Creek served as inputs to the simulation, which was calibrated to the surveyed elevations of high-water marks left by the flood and then used to predict flooding that would result from streamflows corresponding to annual exceedence probabilities of 1 and 2 percent. The simulated extent of the June 11, 2010, flood matched the observed extent of flooding at Albert Pike Recreation Area. The mean depth of inundation in the camp areas was 8.5 feet in Area D, 7.4 feet in Area C, 3.8 feet in Areas A, B, and the Day Use Area, and 12.5 feet in Lowry’s Camp Albert Pike. The mean water velocity was 7.2 feet per second in Area D, 7.6 feet per second in Area C, 7.2 feet per second in Areas A, B, and the Day Use Area, and 7.6 feet per second in Lowry’s Camp Albert Pike. A sensitivity analysis indicated that varying the streamflow of the Little Missouri River had the greatest effect on simulated water-surface elevation, while varying the streamflow of tributary Brier Creek had the least effect. Simulated water-surface elevations were lower than those modeled by the U.S. Forest Service using the standard-step method, but the

Geoarchaeological response to landscape changes of the Greek continental shelf since the Last Glacial Maximum

Science.gov (United States)

Kapsimalis, Vasilios; Pavlopoulos, Kosmas; Panagiotopoulos, Ioannis

2010-05-01

An overview of geological, sedimentological, palaeoclimatic, archaeological and mythological data is presented in order to detect the geomorphological changes of the Aegean and Ionian shelves during the last sea-level transgression, and comprehend the consequent prehistoric human adaptations. The irregular rise of sea level since the Last Glacial Maximum forced the Palaeolithic human to abandon its settlements located near the old (lower) coastlines and to move landward in new positions. Commonly, the coastline movement was very slow causing no significant impact on human activities; however in some cases, the transgression was very prompt causing human migration towards highlands. In some very gentle-dipped and wide regions, e.g. the North Aegean plateau, the sea-level rise caused a rapid coastline retreat (in some extreme case as fast as 10 m/yr) and inundation of an extended surface area. However, at the same time, in the steep parts of the Greek shelf, e.g. the Kyparissiakos Gulf and Crete, the coastline advanced landwards with a slow motion (commonly, a few cm/yr) covering small areas. In addition, coastal regions with particular geomorphologic characteristics, e.g. coastal paleo-lakes protected by a sill (gulfs of Corinth, Amvrakikos, Pagasitikos Evvoikos, Saronikos), were deluged by the sea during different periods and under different intensity, depending on the elevation of the sill and the manner of its overflow. Although the presence of Palaeolithic human in the Greek mainland has been confirmed by several archaeological excavations, there is no certain evidence for human settlement in the deep parts of Greek shelf. However, many archaeologists have suggested that some of Palaeolithic people lived on the shelf, when the sea level was lower than its present position. Nevertheless, some potential Palaeolithic migration routes can be indicated taking into account (a) the palaeogeographic reconstruction of Greek shelf over the Last Quaternary; (b

Test operation of a real-time tsunami inundation forecast system using actual data observed by S-net

Science.gov (United States)

Suzuki, W.; Yamamoto, N.; Miyoshi, T.; Aoi, S.

2017-12-01

If the tsunami inundation information can be rapidly and stably forecast before the large tsunami attacks, the information would have effectively people realize the impeding danger and necessity of evacuation. Toward that goal, we have developed a prototype system to perform the real-time tsunami inundation forecast for Chiba prefecture, eastern Japan, using off-shore ocean bottom pressure data observed by the seafloor observation network for earthquakes and tsunamis along the Japan Trench (S-net) (Aoi et al., 2015, AGU). Because tsunami inundation simulation requires a large computation cost, we employ a database approach searching the pre-calculated tsunami scenarios that reasonably explain the observed S-net pressure data based on the multi-index method (Yamamoto et al., 2016, EPS). The scenario search is regularly repeated, not triggered by the occurrence of the tsunami event, and the forecast information is generated from the selected scenarios that meet the criterion. Test operation of the prototype system using the actual observation data started in April, 2017 and the performance and behavior of the system during non-tsunami event periods have been examined. It is found that the treatment of the noises affecting the observed data is the main issue to be solved toward the improvement of the system. Even if the observed pressure data are filtered to extract the tsunami signals, the noises in ordinary times or unusually large noises like high ocean waves due to storm affect the comparison between the observed and scenario data. Due to the noises, the tsunami scenarios are selected and the tsunami is forecast although any tsunami event does not actually occur. In most cases, the selected scenarios due to the noises have the fault models in the region along the Kurile or Izu-Bonin Trenches, far from the S-net region, or the fault models below the land. Based on the parallel operation of the forecast system with a different scenario search condition and

Effects of bruxism on the maximum bite force

Directory of Open Access Journals (Sweden)

Todić Jelena T.

2017-01-01

Full Text Available Background/Aim. Bruxism is a parafunctional activity of the masticatory system, which is characterized by clenching or grinding of teeth. The purpose of this study was to determine whether the presence of bruxism has impact on maximum bite force, with particular reference to the potential impact of gender on bite force values. Methods. This study included two groups of subjects: without and with bruxism. The presence of bruxism in the subjects was registered using a specific clinical questionnaire on bruxism and physical examination. The subjects from both groups were submitted to the procedure of measuring the maximum bite pressure and occlusal contact area using a single-sheet pressure-sensitive films (Fuji Prescale MS and HS Film. Maximal bite force was obtained by multiplying maximal bite pressure and occlusal contact area values. Results. The average values of maximal bite force were significantly higher in the subjects with bruxism compared to those without bruxism (p 0.01. Maximal bite force was significantly higher in the males compared to the females in all segments of the research. Conclusion. The presence of bruxism influences the increase in the maximum bite force as shown in this study. Gender is a significant determinant of bite force. Registration of maximum bite force can be used in diagnosing and analysing pathophysiological events during bruxism.

Geochemical and sedimentological signature of catastrophic saltwater inundations (tsunami), New Zealand

International Nuclear Information System (INIS)

Chague-Goff, C.; Goff, J.R.

1999-01-01

Three tidal marshes in Able Tasman National Par, New Zealand, were studied using geochemical, sedimentological and radiometric dating techniques. Charcoal and plant material samples were taken from one core in each inlet for 14 C analysis. radiocarbon ages were converted to dendrocalibrated years . All samples produced a terrestrial 13 C signal. Near surface samples were date d by measuring 137 Cs. A 1700 year record of catastrophic saltwater inundations (CSI) events (Tsunami) was produced. Up to four such events were identified, with ruptures of one or more of the Wellington, Wairarapa and Alpine Faults being the most likely tsunamigenic source. CSI signatures include: peaks in Fe and/or S, a peak in fines and contemporaneous or delayed peaks in organic content and/or loss on ignition (LOI). Geochemical data in association with grain size analyses proved to be a valuable tool in the interpretation of these events

The exposure of Sydney (Australia) to earthquake-generated tsunamis, storms and sea level rise: a probabilistic multi-hazard approach.

Science.gov (United States)

Dall'Osso, F; Dominey-Howes, D; Moore, C; Summerhayes, S; Withycombe, G

2014-12-10

Approximately 85% of Australia's population live along the coastal fringe, an area with high exposure to extreme inundations such as tsunamis. However, to date, no Probabilistic Tsunami Hazard Assessments (PTHA) that include inundation have been published for Australia. This limits the development of appropriate risk reduction measures by decision and policy makers. We describe our PTHA undertaken for the Sydney metropolitan area. Using the NOAA NCTR model MOST (Method for Splitting Tsunamis), we simulate 36 earthquake-generated tsunamis with annual probabilities of 1:100, 1:1,000 and 1:10,000, occurring under present and future predicted sea level conditions. For each tsunami scenario we generate a high-resolution inundation map of the maximum water level and flow velocity, and we calculate the exposure of buildings and critical infrastructure. Results indicate that exposure to earthquake-generated tsunamis is relatively low for present events, but increases significantly with higher sea level conditions. The probabilistic approach allowed us to undertake a comparison with an existing storm surge hazard assessment. Interestingly, the exposure to all the simulated tsunamis is significantly lower than that for the 1:100 storm surge scenarios, under the same initial sea level conditions. The results have significant implications for multi-risk and emergency management in Sydney.

Hydrodynamic Modeling Analysis to Support Nearshore Restoration Projects in a Changing Climate

Directory of Open Access Journals (Sweden)

Zhaoqing Yang

2014-01-01

Full Text Available To re-establish the intertidal wetlands with full tidal exchange and improve salmonid rearing habitat in the Skagit River estuary, State of Washington, USA, a diked agriculture farm land along the Skagit Bay front is proposed to be restored to a fully functional tidal wetland. The complex and dynamic Skagit River estuarine system calls for the need of a multi-facet and multi-dimensional analysis using observed data, numerical and analytical methods. To assist the feasibility study of the restoration project, a hydrodynamic modeling analysis was conducted using a high-resolution unstructured-grid coastal ocean model to evaluate the hydrodynamic response to restoration alternatives and to provide guidance to the engineering design of a new levee in the restoration site. A set of parameters were defined to quantify the hydrodynamic response of the nearshore restoration project, such as inundation area, duration of inundation, water depth and salinity of the inundated area. To assist the design of the new levee in the restoration site, the maximum water level near the project site was estimated with consideration of extreme high tide, wind-induced storm surge, significant wave height and future sea-level rise based on numerical model results and coastal engineering calculation.

Assessing suitable area for Acacia dealbata Mill. in the Ceira River Basin (Central Portugal based on maximum entropy modelling approach

Directory of Open Access Journals (Sweden)

Jorge Pereira

2015-12-01

Full Text Available Biological invasion by exotic organisms became a key issue, a concern associated to the deep impacts on several domains described as resultant from such processes. A better understanding of the processes, the identification of more susceptible areas, and the definition of preventive or mitigation measures are identified as critical for the purpose of reducing associated impacts. The use of species distribution modeling might help on the purpose of identifying areas that are more susceptible to invasion. This paper aims to present preliminary results on assessing the susceptibility to invasion by the exotic species Acacia dealbata Mill. in the Ceira river basin. The results are based on the maximum entropy modeling approach, considered one of the correlative modelling techniques with better predictive performance. Models which validation is based on independent data sets present better performance, an evaluation based on the AUC of ROC accuracy measure.

Partitioning of metals in a degraded acid sulfate soil landscape: influence of tidal re-inundation.

Science.gov (United States)

Claff, Salirian R; Sullivan, Leigh A; Burton, Edward D; Bush, Richard T; Johnston, Scott G

2011-11-01

The oxidation and acidification of sulfidic soil materials results in the re-partitioning of metals, generally to more mobile forms. In this study, we examine the partitioning of Fe, Cr, Cu, Mn, Ni and Zn in the acidified surface soil (0-0.1 m) and the unoxidised sub-soil materials (1.3-1.5 m) of an acid sulfate soil landscape. Metal partitioning at this acidic site was then compared to an adjacent site that was previously acidified, but has since been remediated by tidal re-inundation. Differences in metal partitioning were determined using an optimised six-step sequential extraction procedure which targets the "labile", "acid-soluble", "organic", "crystalline oxide", "pyritic" and "residual" fractions. The surficial soil materials of the acidic site had experienced considerable losses of Cr, Cu, Mn and Ni compared to the underlying parent material due to oxidation and acidification, yet only minor losses of Fe and Zn. In general, the metals most depleted from the acidified surface soil materials exhibited the greatest sequestration in the surface soil materials of the tidally remediated site. An exception to this was iron, which accumulated to highly elevated concentrations in the surficial soil materials of the tidally remediated site. The "acid-soluble", "organic" and "pyritic" fractions displayed the greatest increase in metals following tidal remediation. This study demonstrates that prolonged tidal re-inundation of severely acidified acid sulfate soil landscapes leads to the immobilisation of trace metals through the surficial accumulation of iron oxides, organic material and pyrite. Copyright © 2011 Elsevier Ltd. All rights reserved.

Assessment of extreme value distributions for maximum temperature in the Mediterranean area

Science.gov (United States)

Beck, Alexander; Hertig, Elke; Jacobeit, Jucundus

2015-04-01

Extreme maximum temperatures highly affect the natural as well as the societal environment Heat stress has great effects on flora, fauna and humans and culminates in heat related morbidity and mortality. Agriculture and different industries are severely affected by extreme air temperatures. Even more under climate change conditions, it is necessary to detect potential hazards which arise from changes in the distributional parameters of extreme values, and this is especially relevant for the Mediterranean region which is characterized as a climate change hot spot. Therefore statistical approaches are developed to estimate these parameters with a focus on non-stationarities emerging in the relationship between regional climate variables and their large-scale predictors like sea level pressure, geopotential heights, atmospheric temperatures and relative humidity. Gridded maximum temperature data from the daily E-OBS dataset (Haylock et al., 2008) with a spatial resolution of 0.25° x 0.25° from January 1950 until December 2012 are the predictands for the present analyses. A s-mode principal component analysis (PCA) has been performed in order to reduce data dimension and to retain different regions of similar maximum temperature variability. The grid box with the highest PC-loading represents the corresponding principal component. A central part of the analyses is the model development for temperature extremes under the use of extreme value statistics. A combined model is derived consisting of a Generalized Pareto Distribution (GPD) model and a quantile regression (QR) model which determines the GPD location parameters. The QR model as well as the scale parameters of the GPD model are conditioned by various large-scale predictor variables. In order to account for potential non-stationarities in the predictors-temperature relationships, a special calibration and validation scheme is applied, respectively. Haylock, M. R., N. Hofstra, A. M. G. Klein Tank, E. J. Klok, P

The SAFRR Tsunami Scenario: Improving Resilience for California from a Plausible M9 Earthquake near the Alaska Peninsula

Science.gov (United States)

Ross, S.; Jones, L.; Wilson, R. I.; Bahng, B.; Barberopoulou, A.; Borrero, J. C.; Brosnan, D.; Bwarie, J.; Geist, E. L.; Johnson, L.; Kirby, S. H.; Knight, W.; Long, K.; Lynett, P. J.; Miller, K.; Mortensen, C. E.; Nicolsky, D.; Oglesby, D. D.; Perry, S. C.; Plumlee, G. S.; Porter, K. A.; Real, C. R.; Ryan, K. J.; Suleimani, E.; Thio, H. K.; Titov, V.; Wein, A. M.; Whitmore, P.; Wood, N. J.

2013-12-01

The SAFRR Tsunami Scenario models a hypothetical but plausible tsunami, created by an Mw9.1 earthquake occurring offshore from the Alaskan peninsula, and its impacts on the California coast. We present the likely inundation areas, current velocities in key ports and harbors, physical damage and repair costs, economic consequences, environmental impacts, social vulnerability, emergency management, and policy implications for California associated with the tsunami scenario. The intended users are those who must make mitigation decisions before and rapid decisions during future tsunamis. Around a half million people would be present in the scenario's inundation area in residences, businesses, public venues, parks and beaches. Evacuation would likely be ordered for the State of California's maximum mapped tsunami inundation zone, evacuating an additional quarter million people from residences and businesses. Some island and peninsula communities would face particular evacuation challenges because of limited access options and short warning time, caused by the distance between Alaska and California. Evacuations may also be a challenge for certain dependent-care populations. One third of the boats in California's marinas could be damaged or sunk, costing at least 700 million in repairs to boats and docks, and potentially much more to address serious issues due to sediment transport and environmental contamination. Fires would likely start at many sites where fuel and petrochemicals are stored in ports and marinas. Tsunami surges and bores may travel several miles inland up coastal rivers. Debris clean-up and recovery of inundated and damaged areas will take days, months, or years depending on the severity of impacts and the available resources for recovery. The Ports of Los Angeles and Long Beach (POLA/LB) would be shut down for a miniμm of two days due to strong currents. Inundation of dry land in the ports would result in 100 million damages to cargo and additional

Implications of different digital elevation models and preprocessing techniques to delineate debris flow inundation hazard zones in El Salvador

Science.gov (United States)

Anderson, E. R.; Griffin, R.; Irwin, D.

2013-12-01

Heavy rains and steep, volcanic slopes in El Salvador cause numerous landslides every year, posing a persistent threat to the population, economy and environment. Although potential debris inundation hazard zones have been delineated using digital elevation models (DEMs), some disparities exist between the simulated zones and actual affected areas. Moreover, these hazard zones have only been identified for volcanic lahars and not the shallow landslides that occur nearly every year. This is despite the availability of tools to delineate a variety of landslide types (e.g., the USGS-developed LAHARZ software). Limitations in DEM spatial resolution, age of the data, and hydrological preprocessing techniques can contribute to inaccurate hazard zone definitions. This study investigates the impacts of using different elevation models and pit filling techniques in the final debris hazard zone delineations, in an effort to determine which combination of methods most closely agrees with observed landslide events. In particular, a national DEM digitized from topographic sheets from the 1970s and 1980s provide an elevation product at a 10 meter resolution. Both natural and anthropogenic modifications of the terrain limit the accuracy of current landslide hazard assessments derived from this source. Global products from the Shuttle Radar Topography Mission (SRTM) and the Advanced Spaceborne Thermal Emission and Reflection Radiometer Global DEM (ASTER GDEM) offer more recent data but at the cost of spatial resolution. New data derived from the NASA Uninhabited Aerial Vehicle Synthetic Aperture Radar (UAVSAR) in 2013 provides the opportunity to update hazard zones at a higher spatial resolution (approximately 6 meters). Hydrological filling of sinks or pits for current hazard zone simulation has previously been achieved through ArcInfo spatial analyst. Such hydrological processing typically only fills pits and can lead to drastic modifications of original elevation values

Short-term Inundation Forecasting for Tsunamis Version 4.0 Brings Forecasting Speed, Accuracy, and Capability Improvements to NOAA's Tsunami Warning Centers

Science.gov (United States)

Sterling, K.; Denbo, D. W.; Eble, M. C.

2016-12-01

Short-term Inundation Forecasting for Tsunamis (SIFT) software was developed by NOAA's Pacific Marine Environmental Laboratory (PMEL) for use in tsunami forecasting and has been used by both U.S. Tsunami Warning Centers (TWCs) since 2012, when SIFTv3.1 was operationally accepted. Since then, advancements in research and modeling have resulted in several new features being incorporated into SIFT forecasting. Following the priorities and needs of the TWCs, upgrades to SIFT forecasting were implemented into SIFTv4.0, scheduled to become operational in October 2016. Because every minute counts in the early warning process, two major time saving features were implemented in SIFT 4.0. To increase processing speeds and generate high-resolution flooding forecasts more quickly, the tsunami propagation and inundation codes were modified to run on Graphics Processing Units (GPUs). To reduce time demand on duty scientists during an event, an automated DART inversion (or fitting) process was implemented. To increase forecasting accuracy, the forecasted amplitudes and inundations were adjusted to include dynamic tidal oscillations, thereby reducing the over-estimates of flooding common in SIFTv3.1 due to the static tide stage conservatively set at Mean High Water. Further improvements to forecasts were gained through the assimilation of additional real-time observations. Cabled array measurements from Bottom Pressure Recorders (BPRs) in the Oceans Canada NEPTUNE network are now available to SIFT for use in the inversion process. To better meet the needs of harbor masters and emergency managers, SIFTv4.0 adds a tsunami currents graphical product to the suite of disseminated forecast results. When delivered, these new features in SIFTv4.0 will improve the operational tsunami forecasting speed, accuracy, and capabilities at NOAA's Tsunami Warning Centers.

What controls the maximum magnitude of injection-induced earthquakes?

Science.gov (United States)

Eaton, D. W. S.

2017-12-01

Three different approaches for estimation of maximum magnitude are considered here, along with their implications for managing risk. The first approach is based on a deterministic limit for seismic moment proposed by McGarr (1976), which was originally designed for application to mining-induced seismicity. This approach has since been reformulated for earthquakes induced by fluid injection (McGarr, 2014). In essence, this method assumes that the upper limit for seismic moment release is constrained by the pressure-induced stress change. A deterministic limit is given by the product of shear modulus and the net injected fluid volume. This method is based on the assumptions that the medium is fully saturated and in a state of incipient failure. An alternative geometrical approach was proposed by Shapiro et al. (2011), who postulated that the rupture area for an induced earthquake falls entirely within the stimulated volume. This assumption reduces the maximum-magnitude problem to one of estimating the largest potential slip surface area within a given stimulated volume. Finally, van der Elst et al. (2016) proposed that the maximum observed magnitude, statistically speaking, is the expected maximum value for a finite sample drawn from an unbounded Gutenberg-Richter distribution. These three models imply different approaches for risk management. The deterministic method proposed by McGarr (2014) implies that a ceiling on the maximum magnitude can be imposed by limiting the net injected volume, whereas the approach developed by Shapiro et al. (2011) implies that the time-dependent maximum magnitude is governed by the spatial size of the microseismic event cloud. Finally, the sample-size hypothesis of Van der Elst et al. (2016) implies that the best available estimate of the maximum magnitude is based upon observed seismicity rate. The latter two approaches suggest that real-time monitoring is essential for effective management of risk. A reliable estimate of maximum

Forecasting the impact of storm waves and sea-level rise on Midway Atoll and Laysan Island within the Papahānaumokuākea Marine National Monument—a comparison of passive versus dynamic inundation models

Science.gov (United States)

Storlazzi, Curt D.; Berkowitz, Paul; Reynolds, Michelle H.; Logan, Joshua B.

2013-01-01

Two inundation events in 2011 underscored the potential for elevated water levels to damage infrastructure and affect terrestrial ecosystems on the low-lying Northwestern Hawaiian Islands in the Papahānaumokuākea Marine National Monument. The goal of this study was to compare passive "bathtub" inundation models based on geographic information systems (GIS) to those that include dynamic water levels caused by wave-induced set-up and run-up for two end-member island morphologies: Midway, a classic atoll with islands on the shallow (2-8 m) atoll rim and a deep, central lagoon; and Laysan, which is characterized by a deep (20-30 m) atoll rim and an island at the center of the atoll. Vulnerability to elevated water levels was assessed using hindcast wind and wave data to drive coupled physics-based numerical wave, current, and water-level models for the atolls. The resulting model data were then used to compute run-up elevations using a parametric run-up equation under both present conditions and future sea-level-rise scenarios. In both geomorphologies, wave heights and wavelengths adjacent to the island shorelines increased more than three times and four times, respectively, with increasing values of sea-level rise, as more deep-water wave energy could propagate over the atoll rim and larger wind-driven waves could develop on the atoll. Although these increases in water depth resulted in decreased set-up along the islands’ shorelines, the larger wave heights and longer wavelengths due to sea-level rise increased the resulting wave-induced run-up. Run-up values were spatially heterogeneous and dependent on the direction of incident wave direction, bathymetry, and island configuration. Island inundation was modeled to increase substantially when wave-driven effects were included, suggesting that inundation and impacts to infrastructure and terrestrial habitats will occur at lower values of predicted sea-level rise, and thus sooner in the 21st century, than suggested

Deterministic approach for multiple-source tsunami hazard assessment for Sines, Portugal

Science.gov (United States)

Wronna, M.; Omira, R.; Baptista, M. A.

2015-11-01

In this paper, we present a deterministic approach to tsunami hazard assessment for the city and harbour of Sines, Portugal, one of the test sites of project ASTARTE (Assessment, STrategy And Risk Reduction for Tsunamis in Europe). Sines has one of the most important deep-water ports, which has oil-bearing, petrochemical, liquid-bulk, coal, and container terminals. The port and its industrial infrastructures face the ocean southwest towards the main seismogenic sources. This work considers two different seismic zones: the Southwest Iberian Margin and the Gloria Fault. Within these two regions, we selected a total of six scenarios to assess the tsunami impact at the test site. The tsunami simulations are computed using NSWING, a Non-linear Shallow Water model wIth Nested Grids. In this study, the static effect of tides is analysed for three different tidal stages: MLLW (mean lower low water), MSL (mean sea level), and MHHW (mean higher high water). For each scenario, the tsunami hazard is described by maximum values of wave height, flow depth, drawback, maximum inundation area and run-up. Synthetic waveforms are computed at virtual tide gauges at specific locations outside and inside the harbour. The final results describe the impact at the Sines test site considering the single scenarios at mean sea level, the aggregate scenario, and the influence of the tide on the aggregate scenario. The results confirm the composite source of Horseshoe and Marques de Pombal faults as the worst-case scenario, with wave heights of over 10 m, which reach the coast approximately 22 min after the rupture. It dominates the aggregate scenario by about 60 % of the impact area at the test site, considering maximum wave height and maximum flow depth. The HSMPF scenario inundates a total area of 3.5 km2.

Hypoxic conditions and oxygen supply in nests of the mangrove ant, Camponotus anderseni, during and after inundation

DEFF Research Database (Denmark)

Nielsen, Mogens Gissel; Christian, K.; Malte, H.

2009-01-01

The small ant Camponotus anderseni lives exclusively in twigs of the mangrove tree Sonneratia alba, and during inundation, the entrance hole is blocked with a soldier's head which effectively prevents flooding. The nests can be very crowded, with the ants and coccids filling up to 50% of the volume...... is to avoid drowning without suffering anoxia or hypercapnia, and they show a remarkable ability to adapt to the extreme conditions in the mangrove and exploit a niche where the density of other ants is insignificant....

Damage estimation of subterranean building constructions due to groundwater inundation – the GIS-based model approach GRUWAD

Directory of Open Access Journals (Sweden)

R. Schinke

2012-09-01

Full Text Available The analysis and management of flood risk commonly focuses on surface water floods, because these types are often associated with high economic losses due to damage to buildings and settlements. The rising groundwater as a secondary effect of these floods induces additional damage, particularly in the basements of buildings. Mostly, these losses remain underestimated, because they are difficult to assess, especially for the entire building stock of flood-prone urban areas. For this purpose an appropriate methodology has been developed and lead to a groundwater damage simulation model named GRUWAD. The overall methodology combines various engineering and geoinformatic methods to calculate major damage processes by high groundwater levels. It considers a classification of buildings by building types, synthetic depth-damage functions for groundwater inundation as well as the results of a groundwater-flow model. The modular structure of this procedure can be adapted in the level of detail. Hence, the model allows damage calculations from the local to the regional scale. Among others it can be used to prepare risk maps, for ex-ante analysis of future risks, and to simulate the effects of mitigation measures. Therefore, the model is a multifarious tool for determining urban resilience with respect to high groundwater levels.

Identification of storm surge vulnerable areas in the Philippines through the simulation of Typhoon Haiyan-induced storm surge levels over historical storm tracks

Science.gov (United States)

Lapidez, J. P.; Tablazon, J.; Dasallas, L.; Gonzalo, L. A.; Cabacaba, K. M.; Ramos, M. M. A.; Suarez, J. K.; Santiago, J.; Lagmay, A. M. F.; Malano, V.

2015-07-01

Super Typhoon Haiyan entered the Philippine Area of Responsibility (PAR) on 7 November 2013, causing tremendous damage to infrastructure and loss of lives mainly due to the storm surge and strong winds. Storm surges up to a height of 7 m were reported in the hardest hit areas. The threat imposed by this kind of natural calamity compelled researchers of the Nationwide Operational Assessment of Hazards (Project NOAH) which is the flagship disaster mitigation program of the Department of Science and Technology (DOST) of the Philippine government to undertake a study to determine the vulnerability of all Philippine coastal communities to storm surges of the same magnitude as those generated by Haiyan. This study calculates the maximum probable storm surge height for every coastal locality by running simulations of Haiyan-type conditions but with tracks of tropical cyclones that entered PAR from 1948-2013. One product of this study is a list of the 30 most vulnerable coastal areas that can be used as a basis for choosing priority sites for further studies to implement appropriate site-specific solutions for flood risk management. Another product is the storm tide inundation maps that the local government units can use to develop a risk-sensitive land use plan for identifying appropriate areas to build residential buildings, evacuation sites, and other critical facilities and lifelines. The maps can also be used to develop a disaster response plan and evacuation scheme.

Identification of storm surge vulnerable areas in the Philippines through the simulation of Typhoon Haiyan-induced storm surge levels over historical storm tracks

Directory of Open Access Journals (Sweden)

J. P. Lapidez

2015-07-01

Full Text Available Super Typhoon Haiyan entered the Philippine Area of Responsibility (PAR on 7 November 2013, causing tremendous damage to infrastructure and loss of lives mainly due to the storm surge and strong winds. Storm surges up to a height of 7 m were reported in the hardest hit areas. The threat imposed by this kind of natural calamity compelled researchers of the Nationwide Operational Assessment of Hazards (Project NOAH which is the flagship disaster mitigation program of the Department of Science and Technology (DOST of the Philippine government to undertake a study to determine the vulnerability of all Philippine coastal communities to storm surges of the same magnitude as those generated by Haiyan. This study calculates the maximum probable storm surge height for every coastal locality by running simulations of Haiyan-type conditions but with tracks of tropical cyclones that entered PAR from 1948–2013. One product of this study is a list of the 30 most vulnerable coastal areas that can be used as a basis for choosing priority sites for further studies to implement appropriate site-specific solutions for flood risk management. Another product is the storm tide inundation maps that the local government units can use to develop a risk-sensitive land use plan for identifying appropriate areas to build residential buildings, evacuation sites, and other critical facilities and lifelines. The maps can also be used to develop a disaster response plan and evacuation scheme.

Class 1 Areas

Data.gov (United States)

U.S. Environmental Protection Agency — A "Class 1" area is a geographic area recognized by the EPA as being of the highest environmental quality and requiring maximum protection. Class I areas are areas...

THE MAXIMUM AMOUNTS OF RAINFALL FALLEN IN SHORT PERIODS OF TIME IN THE HILLY AREA OF CLUJ COUNTY - GENESIS, DISTRIBUTION AND PROBABILITY OF OCCURRENCE

Directory of Open Access Journals (Sweden)

BLAGA IRINA

2014-03-01

Full Text Available The maximum amounts of rainfall are usually characterized by high intensity, and their effects on the substrate are revealed, at slope level, by the deepening of the existing forms of torrential erosion and also by the formation of new ones, and by landslide processes. For the 1971-2000 period, for the weather stations in the hilly area of Cluj County: Cluj- Napoca, Dej, Huedin and Turda the highest values of rainfall amounts fallen in 24, 48 and 72 hours were analyzed and extracted, based on which the variation and the spatial and temporal distribution of the precipitation were analyzed. The annual probability of exceedance of maximum rainfall amounts fallen in short time intervals (24, 48 and 72 hours, based on thresholds and class values was determined, using climatological practices and the Hyfran program facilities.

Identification of tsunami deposits and liquefaction features in the Gargano area (Italy: paleoseismological implication

Directory of Open Access Journals (Sweden)

L. Graziani

2003-06-01

Full Text Available The Gargano region (Southeastern Italy was hit by a M = 6.8 earthquake and inundated by a subsequent tsunami in 1627. To better define the hazard in the region, we searched for evidence of this and prior earthquakes in the geologic record. We identified potential earthquake-related liquefaction features and tsunami deposits in the stratigraphic sequences of the marsh areas both north and south of the Gargano promontory. We recognized clear liquefaction features and possible tsunamigenic sands that can be related to the 1627 seismic event in irrigation ditch exposures and gouge cores along the Northern Gargano coast. In total, six potential tsunami sand deposits have been recognized in two areas located close to the northern and southern coasts of the Gargano promontory. However, ambiguous evidence comes from the paleontological analysis of these sands. Although fragments of marine shells have been found in the coarser portion of the sand samples, foraminifera and ostracods assemblages are typical of brackish water condition. Radiocarbon dating of three of these deposits from the Northern Gargano coast, near the town of Lesina, suggests an average recurrence interval of 1700 years for tsunami events in this area. Assuming that all the paleotsunamis are related to the same seismogenic source responsible for the 1627 earthquake, this average recurrence interval may be typical for that source. Radiocarbon dating of three sand layers observed on the southern coast, close to the city of Manfredonia, suggests that the average recurrence time for violent sea inundation there is about 1200 years.

Impact of marine reserve on maximum sustainable yield in a traditional prey-predator system

Science.gov (United States)

Paul, Prosenjit; Kar, T. K.; Ghorai, Abhijit

2018-01-01

Multispecies fisheries management requires managers to consider the impact of fishing activities on several species as fishing impacts both targeted and non-targeted species directly or indirectly in several ways. The intended goal of traditional fisheries management is to achieve maximum sustainable yield (MSY) from the targeted species, which on many occasions affect the targeted species as well as the entire ecosystem. Marine reserves are often acclaimed as the marine ecosystem management tool. Few attempts have been made to generalize the ecological effects of marine reserve on MSY policy. We examine here how MSY and population level in a prey-predator system are affected by the low, medium and high reserve size under different possible scenarios. Our simulation works shows that low reserve area, the value of MSY for prey exploitation is maximum when both prey and predator species have fast movement rate. For medium reserve size, our analysis revealed that the maximum value of MSY for prey exploitation is obtained when prey population has fast movement rate and predator population has slow movement rate. For high reserve area, the maximum value of MSY for prey's exploitation is very low compared to the maximum value of MSY for prey's exploitation in case of low and medium reserve. On the other hand, for low and medium reserve area, MSY for predator exploitation is maximum when both the species have fast movement rate.

Seed flotation and germination of salt marsh plants: The effects of stratification, salinity, and/or inundation regime

Science.gov (United States)

Elsey-Quirk, T.; Middleton, B.A.; Proffitt, C.E.

2009-01-01

We examined the effects of cold stratification and salinity on seed flotation of eight salt marsh species. Four of the eight species were tested for germination success under different stratification, salinity, and flooding conditions. Species were separated into two groups, four species received wet stratification and four dry stratification and fresh seeds of all species were tested for flotation and germination. Fresh seeds of seven out of eight species had flotation times independent of salinity, six of which had average flotation times of at least 50 d. Seeds of Spartina alterniflora and Spartina patens had the shortest flotation times, averaging 24 and 26 d, respectively. Following wet stratification, the flotation time of S. alterniflora seeds in higher salinity water (15 and 36 ppt) was reduced by over 75% and germination declined by more than 90%. Wet stratification reduced the flotation time of Distichlis spicata seeds in fresh water but increased seed germination from 2 to 16% in a fluctuating inundation regime. Fresh seeds of Iva frutescens and S. alternflora were capable of germination and therefore are non-dormant during dispersal. Fresh seeds of I. frutescens had similar germination to dry stratified seeds ranging 25-30%. Salinity reduced seed germination for all species except for S. alterniflora. A fluctuating inundation regime was important for seed germination of the low marsh species and for germination following cold stratification. The conditions that resulted in seeds sinking faster were similar to the conditions that resulted in higher germination for two of four species. ?? 2009 Elsevier B.V.

Scenario-based numerical modelling and the palaeo-historic record of tsunamis in Wallis and Futuna, Southwest Pacific

Science.gov (United States)

Lamarche, G.; Popinet, S.; Pelletier, B.; Mountjoy, J.; Goff, J.; Delaux, S.; Bind, J.

2015-08-01

We investigated the tsunami hazard in the remote French territory of Wallis and Futuna, Southwest Pacific, using the Gerris flow solver to produce numerical models of tsunami generation, propagation and inundation. Wallis consists of the inhabited volcanic island of Uvéa that is surrounded by a lagoon delimited by a barrier reef. Futuna and the island of Alofi form the Horn Archipelago located ca. 240 km east of Wallis. They are surrounded by a narrow fringing reef. Futuna and Alofi emerge from the North Fiji Transform Fault that marks the seismically active Pacific-Australia plate boundary. We generated 15 tsunami scenarios. For each, we calculated maximum wave elevation (MWE), inundation distance and expected time of arrival (ETA). The tsunami sources were local, regional and distant earthquake faults located along the Pacific Rim. In Wallis, the outer reef may experience 6.8 m-high MWE. Uvéa is protected by the barrier reef and the lagoon, but inundation depths of 2-3 m occur in several coastal areas. In Futuna, flow depths exceeding 2 m are modelled in several populated areas, and have been confirmed by a post-September 2009 South Pacific tsunami survey. The channel between the islands of Futuna and Alofi amplified the 2009 tsunami, which resulted in inundation distance of almost 100 m and MWE of 4.4 m. This first ever tsunami hazard modelling study of Wallis and Futuna compares well with palaeotsunamis recognised on both islands and observation of the impact of the 2009 South Pacific tsunami. The study provides evidence for the mitigating effect of barrier and fringing reefs from tsunamis.

Approximate maximum parsimony and ancestral maximum likelihood.

Science.gov (United States)

Alon, Noga; Chor, Benny; Pardi, Fabio; Rapoport, Anat

2010-01-01

We explore the maximum parsimony (MP) and ancestral maximum likelihood (AML) criteria in phylogenetic tree reconstruction. Both problems are NP-hard, so we seek approximate solutions. We formulate the two problems as Steiner tree problems under appropriate distances. The gist of our approach is the succinct characterization of Steiner trees for a small number of leaves for the two distances. This enables the use of known Steiner tree approximation algorithms. The approach leads to a 16/9 approximation ratio for AML and asymptotically to a 1.55 approximation ratio for MP.

Effect of Tide Elevation on Extratropical Storm Surge in Northwest Europe

Science.gov (United States)

Keshtpoor, M.; Carnacina, I.; Yablonsky, R. M.

2016-12-01

Extratropical cyclones (ETCs) are the major storm surge-generating meteorological events in northwest Europe. The total water level increase induced by these ETCs is significantly influenced by the local tidal range, which exceeds 8 meters along the southwestern UK coastline. In particular, a surge-generating ETC during high tide may put coastal assets and infrastructure in risk. Also, during low tide, the risk of surge induced by extreme ETC events is diminished. Here, the effect of tidal elevation on storm surge is investigated at 196 tide gauges in northwest Europe. A numerical, hydrodynamic model was developed using Delft3D-FM framework to simulate the coastal hydrodynamics during ETCs. Then, 1750 historical events were simulated to investigate the pattern of coastal inundation. Results suggest that in areas with a large tidal range ( 8 meters) and during the time period surrounding high or low tide, the pattern of coastal hydrodynamics is governed by tide and not storm surge. This result is most evident near the English Channel and Bristol Channel, where low frequency maximum water levels are observed when storm surge is combined with high tide. In contrast, near the tidal phase reversal, coastal hydrodynamics responds primarily to the storm surge, and low frequency maximum water elevation largely depends on the surge. In the areas with a small tidal range, ETC strength determines the pattern of coastal inundation.

Modeling the October 2005 lahars at Panabaj (Guatemala)

Science.gov (United States)

Charbonnier, S. J.; Connor, C. B.; Connor, L. J.; Sheridan, M. F.; Oliva Hernández, J. P.; Richardson, J. A.

2018-01-01

An extreme rainfall event in October of 2005 triggered two deadly lahars on the flanks of Tolimán volcano (Guatemala) that caused many fatalities in the village of Panabaj. We mapped the deposits of these lahars, then developed computer simulations of the lahars using the geologic data and compared simulated area inundated by the flows to mapped area inundated. Computer simulation of the two lahars was dramatically improved after calibration with geological data. Specifically, detailed field measurements of flow inundation area, flow thickness, flow direction, and velocity estimates, collected after lahar emplacement, were used to calibrate the rheological input parameters for the models, including deposit volume, yield strength, sediment and water concentrations, and Manning roughness coefficients. Simulations of the two lahars, with volumes of 240,200 ± 55,400 and 126,000 ± 29,000 m3, using the FLO-2D computer program produced models of lahar runout within 3% of measured runouts and produced reasonable estimates of flow thickness and velocity along the lengths of the simulated flows. We compare areas inundated using the Jaccard fit, model sensitivity, and model precision metrics, all related to Bayes' theorem. These metrics show that false negatives (areas inundated by the observed lahar where not simulated) and false positives (areas not inundated by the observed lahar where inundation was simulated) are reduced using a model calibrated by rheology. The metrics offer a procedure for tuning model performance that will enhance model accuracy and make numerical models a more robust tool for natural hazard reduction.

SEA LEVEL RISE AND ITS POTENTIAL IMPACTS ON COASTAL URBAN AREA: A CASE OF ETI-OSA, NIGERIA

Directory of Open Access Journals (Sweden)

Ayodele Michael AGBOOLA

2016-10-01

Full Text Available This study examines the spatial extent of coastal urban development and its potential sensitivity to sea-level rise. The main aim of the study is to critically examine the extent of growth in Eti-Osa over time, and the potential impacts of sea leve rise. Landsat Enhanced Thematic Mapper Plus (ETM+ imageries of years 2000 and 2015 were used to evaluate the different land use type identified. Post-classification change detection method was used to evaluate the output of the maximum likelihood supervised classification analysis done. This was also used to estimate the changes induces through urban development on the environment which accounts for the biodiversity loss. ASTER GDEM 2 imagery of 2011 was used to generate the elevation data used for the inundation analysis. Thus, both Land use map of Eti-Osa in 2015 and the down scaled Sea-level rise scenarios (at 0.5 to 15 meters were used for the inundation mapping. Results obtained from this research affirms that indeed EtiOsa has been subjected to gross urban expansion giving room for diverse forms of environmental degradation among which are huge replacement of natural land cover with built-up, reclamation of wetlands and sand filling of water bodies. This basically illustrates growth but also the risk that accompanies the advent of excessive alteration of natural ecosystem as Sea-level rise projections imply in this research.

Changes in Land Surface Water Dynamics since the 1990s and Relation to Population Pressure

Science.gov (United States)

Prigent, C.; Papa, F.; Aires, F.; Jimenez, C.; Rossow, W. B.; Matthews, E.

2012-01-01

We developed a remote sensing approach based on multi-satellite observations, which provides an unprecedented estimate of monthly distribution and area of land-surface open water over the whole globe. Results for 1993 to 2007 exhibit a large seasonal and inter-annual variability of the inundation extent with an overall decline in global average maximum inundated area of 6% during the fifteen-year period, primarily in tropical and subtropical South America and South Asia. The largest declines of open water are found where large increases in population have occurred over the last two decades, suggesting a global scale effect of human activities on continental surface freshwater: denser population can impact local hydrology by reducing freshwater extent, by draining marshes and wetlands, and by increasing water withdrawals. Citation: Prigent, C., F. Papa, F. Aires, C. Jimenez, W. B. Rossow, and E. Matthews (2012), Changes in land surface water dynamics since the 1990s and relation to population pressure, in section 4, insisting on the potential applications of the wetland dataset.

Prediction by numerical modeling of the risk zone along a riverside exposed to a dam failure; Prevision par modelisation numerique de la zone de risque bordant un troncon de riviere subissant une rupture de barrage

Energy Technology Data Exchange (ETDEWEB)

Mahdi, T.F.

2004-07-01

The risk zone associated with the surge wave following dam failure is defined in this study using a newly developed methodology that incorporates the conventionally used maximum water levels, the sediment movement in the river bed and the possibility of bank failure. Although the risk zone is typically defined as the inundated area, extensive lateral erosion that causes landslides could also accompany the inundation. This study demonstrates that the stability of the riverbank (in terms of geotechnical considerations) can influence the delineation of the risk area. The combined disciplines of geotechnics and hydraulics can be used to follow the evolution of the riverbed and riverbanks during a flood event. This study also presents a structured methodology for the St. Venant shallow water wave equations which were used to determine the area likely to be flooded without taking into account sediment transport. It also discusses aspects of the sediment transport theory. Fluvial erosion and lateral bank failure are the basic physical processes responsible for bank retreat. The minimum energy dissipation rate theory is applied for fluvial erosion, while Bishop's modified method is used to analyze slope stability when evaluating lateral bank failures. A numerical modeling of flows over movable beds is presented along with a review of some of the available numerical models. A diagnostic phase that provides information needed to qualify the extent of the damage after a flood is also presented. Some of the numerical models to evaluate risk area were validated on a portion of the HaHa River which was affected in the 1996 Saguenay flood. The new methodology, applied to the Outaouais River at Notre Dame du Nord in Quebec, produces a risk area much greater than that obtained when only the inundated area is considered.

Effect of Variable Manning Coefficients on Tsunami Inundation

Science.gov (United States)

Barberopoulou, A.; Rees, D.

2017-12-01

Numerical simulations are commonly used to help estimate tsunami hazard, improve evacuation plans, issue or cancel tsunami warnings, inform forecasting and hazard assessments and have therefore become an integral part of hazard mitigation among the tsunami community. Many numerical codes exist for simulating tsunamis, most of which have undergone extensive benchmarking and testing. Tsunami hazard or risk assessments employ these codes following a deterministic or probabilistic approach. Depending on the scope these studies may or may not consider uncertainty in the numerical simulations, the effects of tides, variable friction or estimate financial losses, none of which are necessarily trivial. Distributed manning coefficients, the roughness coefficients used in hydraulic modeling, are commonly used in simulating both riverine and pluvial flood events however, their use in tsunami hazard assessments is primarily part of limited scope studies and for the most part, not a standard practice. For this work, we investigate variations in manning coefficients and their effects on tsunami inundation extent, pattern and financial loss. To assign manning coefficients we use land use maps that come from the New Zealand Land Cover Database (LCDB) and more recent data from the Ministry of the Environment. More than 40 classes covering different types of land use are combined into major classes such as cropland, grassland and wetland representing common types of land use in New Zealand, each of which is assigned a unique manning coefficient. By utilizing different data sources for variable manning coefficients, we examine the impact of data sources and classification methodology on the accuracy of model outputs.

TSUNAMI DEPOSITS AT QUEEN’S BEACH, OAHU, HAWAII – INITIALRESULTS AND WAVE MODELING

Directory of Open Access Journals (Sweden)

Dr. Barbara Keating

2004-01-01

Full Text Available Photographs taken immediately after the 1946 Aleutian Tsunami inundated Queen’s Beach, southeastern Oahu, show the major highway around the island was inundated and the road bed was destroyed. That road bed remains visible today, in an undeveloped coastline that shows like change in sedimentary deposits between 1946 and today (based on photographic evidence. Tsunami catalog records however indicate that the beach was repeatedly inundated by tsunami in 1946, 1952, 1957, and 1960. Tsunami runup was reported to have reached between 3 and 11 m elevation. Eyewitness accounts however indicate inundations of up to 20 m in Kealakipapa Valley (Makapu’u Lookout during 1946 and photographic evidence indicated inundation reached 9 m in 1957. The inundation of Kealakipapa Valley has been successfully modeled using a 10-m tsunami wave model.A comparison of the modern beach deposits to those near the remains of the destroyed highway demonstrate that the sedimentary deposits within the two areas have very different rock characteristics. We conclude the modern beach is dominated by the rounding of rocks (mostly coral by wave activity. However, in the area that has experienced prior tsunami inundations, the rocks are characterized by fracturing and a high component of basaltic material. We conclude the area near the destroyed highway reflects past tsunami inundations combined with inevitable anthropogenic alteration.

Community exposure to tsunami hazards in Hawai‘i

Science.gov (United States)

Jones, Jamie L.; Jamieson, Matthew R.; Wood, Nathan J.

2016-06-17

Hawai‘i has experienced numerous destructive tsunamis and the potential for future inundation has been described over the years using various historical events and scenarios. To support tsunami preparedness and risk-reduction planning in Hawai‘i, this study documents the variations among 91 coastal communities and 4 counties in the amounts, types, and percentages of developed land, residents, employees, community-support businesses, dependent-care facilities, public venues, and critical facilities in a composite extreme tsunami-inundation zone associated with two great Aleutian moment magnitude (Mw) 9.3 and 9.6 earthquake scenarios. These earthquake scenarios are considered to provide the maximum tsunami scenario for the Hawaiian Islands. According to 2010 U.S. Census Bureau data, the Hawai‘i extreme tsunami-inundation zone contains approximately 248,749 residents and 91,528 households (18 and 20 percent, respectively, of State totals). The residential population in tsunami-prone areas is racially diverse, with most residents identifying themselves as White (47 percent of the total exposed population), Asian (48 percent), or Native Hawaiian and Other Pacific Islander (29 percent), either alone or in combination with one or more other races (note that race categories do not sum to 100 percent because individuals were able to report multiple races in the 2010 U.S. Census). A total of 50,016 households are renter-occupied, making up 55 percent of total households in the extreme inundation zone. The extreme tsunami-inundation zone contains 18,693 businesses (37 percent of State totals) and 245,827 employees (42 percent of the State labor force). The employee population in the extreme tsunami-inundation zone is largely in the accommodation and food services and retail-trade sectors. Although occupancy values are not known for each facility, the extreme tsunami-inundation zone also contains numerous community-support businesses (for example, religious organizations

Producción de riesgos de desastre en áreas inundables. Las transformaciones recientes en la urbanización del Municipio de Tigre (Argentina

Directory of Open Access Journals (Sweden)

Diego Ríos

2011-12-01

Full Text Available En el trabajo se analizan las relaciones entre urbanización de áreas inundables, técnicas constructivas de mitigación y producción de espacio de riesgos de desastre. Ello se efectúa a través de un caso de estudio: las transformaciones recientes en la urbanización de los bañados del municipio de Tigre protagonizadas por la expansión de urbanizaciones cerradas en un contexto de profundo desarrollo desigual. Los grandes rellenos fueron las técnicas constructivas implementadas para la incorporación urbana de esas tierras inundables produciendo una transformación inaudita del paisaje de los bañados. En este caso, las necesidades de reproducción del capital inmobiliario-financiero (viabilizadas por el accionar del Estado han producido no sólo nuevas formas de espacio urbano y de urbanización en los bañados de Tigre, sino también un espacio de riesgo de desastre desigual, cuyas consecuencias han sido escasamente consideradas.

Influence of Dynamic Neuromuscular Stabilization Approach on Maximum Kayak Paddling Force

Directory of Open Access Journals (Sweden)

Davidek Pavel

2018-03-01

Full Text Available The purpose of this study was to examine the effect of Dynamic Neuromuscular Stabilization (DNS exercise on maximum paddling force (PF and self-reported pain perception in the shoulder girdle area in flatwater kayakers. Twenty male flatwater kayakers from a local club (age = 21.9 ± 2.4 years, body height = 185.1 ± 7.9 cm, body mass = 83.9 ± 9.1 kg were randomly assigned to the intervention or control groups. During the 6-week study, subjects from both groups performed standard off-season training. Additionally, the intervention group engaged in a DNS-based core stabilization exercise program (quadruped exercise, side sitting exercise, sitting exercise and squat exercise after each standard training session. Using a kayak ergometer, the maximum PF stroke was measured four times during the six weeks. All subjects completed the Disabilities of the Arm, Shoulder and Hand (DASH questionnaire before and after the 6-week interval to evaluate subjective pain perception in the shoulder girdle area. Initially, no significant differences in maximum PF and the DASH questionnaire were identified between the two groups. Repeated measures analysis of variance indicated that the experimental group improved significantly compared to the control group on maximum PF (p = .004; Cohen’s d = .85, but not on the DASH questionnaire score (p = .731 during the study. Integration of DNS with traditional flatwater kayak training may significantly increase maximum PF, but may not affect pain perception to the same extent.

NATURAL HAZARD ASSESSMENT OF SW MYANMAR - A CONTRIBUTION OF REMOTE SENSING AND GIS METHODS TO THE DETECTION OF AREAS VULNERABLE TO EARTHQUAKES AND TSUNAMI / CYCLONE FLOODING

Directory of Open Access Journals (Sweden)

George Pararas-Carayannis

2009-01-01

Full Text Available Myanmar, formerly Burma, is vulnerable to several natural hazards, such as earthquakes, cyclones, floods, tsunamis and landslides. The present study focuses on geomorphologic and geologic investigations of the south-western region of the country, based on satellite data (Shuttle Radar Topography Mission-SRTM, MODIS and LANDSAT. The main objective is to detect areas vulnerable to inundation by tsunami waves and cyclone surges. Since the region is also vulnerable to earthquake hazards, it is also important to identify seismotectonic patterns, the location of major active faults, and local site conditions that may enhance ground motions and earthquake intensities. As illustrated by this study, linear, topographic features related to subsurface tectonic features become clearly visible on SRTM-derived morphometric maps and on LANDSAT imagery. The GIS integrated evaluation of LANDSAT and SRTM data helps identify areas most susceptible to flooding and inundation by tsunamis and storm surges. Additionally, land elevation maps help identify sites greater than 10 m in elevation height, that would be suitable for the building of protective tsunami/cyclone shelters.

Hurricane Harvey Riverine Flooding: Part 2: Integration of Heterogeneous Earth Observation Data for Comparative Analysis with High-Resolution Inundation Boundaries Reconstructed from Flood2D-GPU Model

Science.gov (United States)

Jackson, C.; Sava, E.; Cervone, G.

2017-12-01

Hurricane Harvey has been noted as the wettest cyclone on record for the US as well as the most destructive (so far) for the 2017 hurricane season. An entire year worth of rainfall occurred over the course of a few days. The city of Houston was greatly impacted as the storm lingered over the city for five days, causing a record-breaking 50+ inches of rain as well as severe damage from flooding. Flood model simulations were performed to reconstruct the event in order to better understand, assess, and predict flooding dynamics for the future. Additionally, number of remote sensing platforms, and on ground instruments that provide near real-time data have also been used for flood identification, monitoring, and damage assessment. Although both flood models and remote sensing techniques are able to identify inundated areas, rapid and accurate flood prediction at a high spatio-temporal resolution remains a challenge. Thus a methodological approach which fuses the two techniques can help to better validate what is being modeled and observed. Recent advancements in data fusion techniques of remote sensing with near real time heterogeneous datasets have allowed emergency responders to more efficiently extract increasingly precise and relevant knowledge from the available information. In this work the use of multiple sources of contributed data, coupled with remotely sensed and open source geospatial datasets is demonstrated to generate an understanding of potential damage assessment for the floods after Hurricane Harvey in Harris County, Texas. The feasibility of integrating multiple sources at different temporal and spatial resolutions into hydrodynamic models for flood inundation simulations is assessed. Furthermore the contributed datasets are compared against a reconstructed flood extent generated from the Flood2D-GPU model.

Floodplain simulation for Musi River using integrated 1D/2D hydrodynamic model

Directory of Open Access Journals (Sweden)

Al Amin Muhammad B.

2017-01-01

Full Text Available This paper presents the simulation of floodplain at Musi River using integrated 1D and 2D hydrodynamic model. The 1D flow simulation was applied for the river channel with flow hydrograph as upstream boundary condition. The result of 1D flow simulation was integrated into 2D flow simulation in order to know the area and characteristics of flood inundation. The input data of digital terrain model which was used in this research had grid resolution of 10m×10m, but for 2D simulation the resolution was with grid resolution 50 m × 50 m so as to limit simulation time since the model size was big enough. The result of the simulation showed that the inundated area surrounding Musi River is about 107.44 km2 with maximum flood depth is 3.24 m, water surface velocity ranges from 0.00 to 0.83 m/s. Most of floodplain areas varied from middle to high flood hazard level, and only few areas had very high level of flood hazard especially on river side. The structural flood control measurement to be recommended to Palembang is to construct flood dike and flood gate. The non structural measurement one is to improve watershed management and socialization of flood awareness.

Flood hydrology and dam-breach hydraulic analyses of four reservoirs in the Black Hills, South Dakota

Science.gov (United States)

Hoogestraat, Galen K.

2011-01-01

Extensive information about the construction of dams or potential downstream hazards in the event of a dam breach is not available for many small reservoirs within the Black Hills National Forest. In 2009, the U.S. Forest Service identified the need for reconnaissance-level dam-breach assessments for four of these reservoirs within the Black Hills National Forest (Iron Creek, Horsethief, Lakota, and Mitchell Lakes) with the potential to flood downstream structures. Flood hydrology and dam-breach hydraulic analyses for the four selected reservoirs were conducted by the U.S. Geological Survey in cooperation with the U.S. Forest service to estimate the areal extent of downstream inundation. Three high-flow breach scenarios were considered for cases when the dam is in place (overtopped) and when a dam break (failure) occurs: the 100-year recurrence 24-hour precipitation, 500-year recurrence peak flow, and the probable maximum precipitation. Inundation maps were developed that show the estimated extent of downstream floodwaters from simulated scenarios. Simulation results were used to determine the hazard classification of a dam break (high, significant, or low), based primarily on the potential for loss of life or property damage resulting from downstream inundation because of the flood surge.The inflow design floods resulting from the two simulated storm events (100-year 24-hour and probable maximum precipitation) were determined using the U.S. Army Corps of Engineers Hydrologic Engineering Center Hydrologic Modeling System (HEC-HMS). The inflow design flood for the 500-year recurrence peak flow was determined by using regional regression equations developed for streamflow-gaging stations with similar watershed characteristics. The step-backwater hydraulic analysis model, Hydrologic Engineering Center's River Analysis System (HEC-RAS), was used to determine water-surface profiles of in-place and dam-break scenarios for the three inflow design floods that were

THE INFLUENCE OF COASTAL CONDITIONS TO TSUNAMI INUNDATION OF BIMA BAY, WEST NUSA TENGGARA

Directory of Open Access Journals (Sweden)

Yudhicara Yudhicara

2017-07-01

Full Text Available Area along the coast that includes the territorial waters of the Bima Bay, West Nusa Tenggara, is prone to tsunamis, evidenced by the historical tsunamis record in 1815 due to the volcanic eruption of Tambora, 1818, 1836 and 1992 caused by earthquakes associated with tectonic system in the north of the island of Sumbawa, and 1892 were sourced from a distant source. Based on the coastal characteristics, the research area was divided into four types of beaches, namely: Steep rocky beach; Coastal walled plain; Flat coastal mangroves; and Flat sandy beaches. According to the lateral measurement, houses were built in the plains with a minimum height difference of 0.04 m at Rababuntu beach and a maximum of 22.63 m in New Asakota area. The settlement closest distance to the coastline is 10.3 m in Rababuntu, while the farthest extent is at Kawananta 194.58 m from the shoreline. The local bathymetry range between 1 and 42.5 m, where the inside of the very shallow waters of the Bay of Bima, gradually steeper at the mouth of the bay to the open sea. This conditions will influence the wave when entering the bay. It will come with large enough speed at the mouth of the bay, spread along the coastal waters of the eastern and continue spreading to all parts with the diminishing velocity, but the height increasing when it reaches shallow water, especially in the waters of the western Gulf of Bima. Several factors can affect the amount of risk that would be caused by the tsunami, in the research area include are: (1 The research area is located in an enclosed bay; (2 The local sea floor depths around the bay is relatively shallow waters; (3 Coastal characteristics of the research area is dominated by a gently sloping beach morphology with low relief, especially in the area of ??Bajo, Rababuntu and Bontokape and other beaches in the city of Bima; (4 Residential location very close to the shoreline; (5 Minimal vegetation cover; and (6 The presence of the

Determination of the wind power systems load to achieve operation in the maximum energy area

Science.gov (United States)

Chioncel, C. P.; Tirian, G. O.; Spunei, E.; Gillich, N.

2018-01-01

This paper analyses the operation of the wind turbine, WT, in the maximum power point, MPP, by linking the load of the Permanent Magnet Synchronous Generator, PMSG, with the wind speed value. The load control methods at wind power systems aiming an optimum performance in terms of energy are based on the fact that the energy captured by the wind turbine significantly depends on the mechanical angular speed of the wind turbine. The presented control method consists in determining the optimal mechanical angular speed, ωOPTIM, using an auxiliary low power wind turbine, WTAUX, operating without load, at maximum angular velocity, ωMAX. The method relies on the fact that the ratio ωOPTIM/ωMAX has a constant value for a given wind turbine and does not depend on the time variation of the wind speed values.

Territorial Vulnerability Assessment Supporting Risk Managing Coastal Areas Due to Tsunami Impact

Directory of Open Access Journals (Sweden)

José Leandro Barros

2015-09-01

Full Text Available Portugal’s coastline extends 1187 km. It is characterized by social, economic and physical conditions that differentiate it from the rest of the territory, including population density, location of infrastructure and support of tourism activities. Therefore, it has a significant exposure if a tsunami occurs. Six coastal study sites with varying characteristics were selected for evaluation in this paper, including two core beach-use areas, two residential areas and two industrial areas. These sites are located in the municipalities of Figueira da Foz, Setúbal and Vila do Bispo. The analysis began with the calculation of the potential tsunami inundation area for each site using the 1755 Lisbon tsunami. Next, a methodology distinguished by its multidimensional character was applied to assess local vulnerability to tsunamis. This methodology assesses vulnerabilities associated with morphological, structural, social and tax factors. These four vulnerability components were combined to obtain a Composite Vulnerability Index (CVI, which enabled us to identify the most vulnerable areas and to determine the distinguishing characteristics of each area.

Characterization of phosphorus in the sedimentary environments of inundated agricultural soils around the Huainan Coal Mines, Anhui, China.

Science.gov (United States)

Yi, Qitao; Xie, Kai; Sun, Pengfei; Kim, Youngchul

2014-02-15

Extensive coal mining in the Huainan Coal Mines, Anhui China, in light of the local hydrology and geology, has resulted in extensive land subsidence and submergence around the mines. This has led to the formation of large (>100 km(2)) lakes. Three representative lakes were selected to study the mechanisms of phosphorus (P) unavailability for primary production from the perspective of sedimentary environments, which in turn owe their formation to permanently inundated agricultural soils. Two important issues were considered: (1) potential of P transport from the cultivated soil column toward surface sediments and (2) characterization of P behavior in view of regional ecological rehabilitation and conservation. Accordingly, we conducted field sediment analyses, combined with simulation experiments of soil column inundation/submergence lasting for four months. Enrichment of Fe-(hydr)oxides in surface sediments was verified to be the main reason for limitations in regional P availability in water bodies. Iron (Fe), but not its bound P, moved upward from the submerged soil column to the surface. However, an increasing upward gradient in the contents of organic matter (OM), total nitrogen (N), total phosphorus (TP), and different P fractions was caused by spatial heterogeneity in soil properties. Phosphorus was unable to migrate upward toward the surface sediments as envisioned, because of complex secondary reactions within soil minerals. Phosphorus bound to Fe and/or Al comprised over 50% of TP, which has important implications for local ecological rehabilitation and water conservation. Copyright © 2013 Elsevier B.V. All rights reserved.

Maximum permissible dose

International Nuclear Information System (INIS)

Anon.

1979-01-01

This chapter presents a historic overview of the establishment of radiation guidelines by various national and international agencies. The use of maximum permissible dose and maximum permissible body burden limits to derive working standards is discussed

DEM-based Approaches for the Identification of Flood Prone Areas

Science.gov (United States)

Samela, Caterina; Manfreda, Salvatore; Nardi, Fernando; Grimaldi, Salvatore; Roth, Giorgio; Sole, Aurelia

2013-04-01

The remarkable number of inundations that caused, in the last decades, thousands of deaths and huge economic losses, testifies the extreme vulnerability of many Countries to the flood hazard. As a matter of fact, human activities are often developed in the floodplains, creating conditions of extremely high risk. Terrain morphology plays an important role in understanding, modelling and analyzing the hydraulic behaviour of flood waves. Research during the last 10 years has shown that the delineation of flood prone areas can be carried out using fast methods that relay on basin geomorphologic features. In fact, the availability of new technologies to measure surface elevation (e.g., GPS, SAR, SAR interferometry, RADAR and LASER altimetry) has given a strong impulse to the development of Digital Elevation Models (DEMs) based approaches. The identification of the dominant topographic controls on the flood inundation process is a critical research question that we try to tackle with a comparative analysis of several techniques. We reviewed four different approaches for the morphological characterization of a river basin with the aim to provide a description of their performances and to identify their range of applicability. In particular, we explored the potential of the following tools. 1) The hydrogeomorphic method proposed by Nardi et al. (2006) which defines the flood prone areas according to the water level in the river network through the hydrogeomorphic theory. 2) The linear binary classifier proposed by Degiorgis et al. (2012) which allows distinguishing flood-prone areas using two features related to the location of the site under exam with respect to the nearest hazard source. The two features, proposed in the study, are the length of the path that hydrologically connects the location under exam to the nearest element of the drainage network and the difference in elevation between the cell under exam and the final point of the same path. 3) The method by

Stocking and structure for maximum growth in sugar maple selection stands.

Science.gov (United States)

Thomas R. Crow; Carl H. Tubbs; Rodney D. Jacobs; Robert R. Oberg

1981-01-01

The impacts of stocking, structure, and cutting cycle on basal area, cubic foot volume, board foot volume, and diameter growth are considered. Recommendations are provided for maximum growth in uneven-aged sugar maple stands.

Dinâmica da mobilização de elementos em solos da Amazônia submetidos à inundação Dinamics of elements in soils from Amazonia after controlled inundation

Directory of Open Access Journals (Sweden)

Hedinaldo Narciso Lima

2005-09-01

Full Text Available Parte significativa de solos da Amazônia permanece saturada ou inundada por períodos que podem variar de alguns dias a vários meses, em decorrência de enchentes ou deficiência de drenagem em algumas áreas, resultando em alterações químicas, físicas e biológicas nos solos. Este trabalho foi conduzido com o objetivo de avaliar a dinâmica da mobilização de Al, Ca, Fe, K, Mg, Mn, Na, Si e P em solos da Amazônia submetidos a inundação. Amostras de vários solos foram submetidas à inundação durante seis meses. Alíquotas da solução foram coletadas periodicamente durante o tempo de inundação e determinaram-se os teores dos diversos elementos em solução. A inundação influenciou a cinética dos elementos, com aumento da mobilização dos mesmos, principalmente, nas primeiras semanas. Os teores de Fe em solução foram mais elevados para os solos mais ricos em Fe amorfo. Em amostras com baixos teores de Fe amorfo e baixo conteúdo de matéria orgânica, os teores de Fe em solução foram muito reduzidos. O teor de P em solução foi influenciado por todas as formas de P. O P ligado ao Fe foi a forma que maior influência exerceu sobre o teor de P solúvel. Os teores dos cátions Ca, Mg, K e Na, em solução, foram diretamente influenciados por seus respectivos teores trocáveis, bem como pela cinética do Fe e do Mn.Significant part of Amazonia soils stays partially or completely waterlogged for varying periods of days to months, as result of widespread inundation or drainage deficiency in some areas, causing changes in chemical, physical and biological properties. In this work, we aimed to evaluate the dynamics of mobilization of Al, Ca, Fe, K, Mg, Mn, Na, Si, P in soils subjected to controlled six months inundation. Soil solution aliquots were collected periodically during the inundation period, determining all elements in solution. The inundation influenced the kinetics of elements, increasing their mobilization, notably in

Potential effects of sea-level rise on plant productivity: Species-specific responses in northeast Pacific tidal marshes

Science.gov (United States)

Janousek, Christopher; Buffington, Kevin J.; Thorne, Karen M.; Guntenspergen, Glenn R.; Takekawa, John Y.; Dugger, Bruce D.

2016-01-01

Coastal wetland plants are adapted to varying degrees of inundation. However, functional relationships between inundation and productivity are poorly characterized for most species. Determining species-specific tolerances to inundation is necessary to evaluate sea-level rise (SLR) effects on future marsh plant community composition, quantify organic matter inputs to marsh accretion, and inform predictive modeling of tidal wetland persistence. In 2 macrotidal estuaries in the northeast Pacific we grew 5 common species in experimental mesocosms across a gradient of tidal elevations to assess effects on growth. We also tested whether species abundance distributions along elevation gradients in adjacent marshes matched productivity profiles in the mesocosms. We found parabolic relationships between inundation and total plant biomass and shoot counts in Spartina foliosa and Bolboschoenus maritimus in California, USA, and in Carex lyngbyei in Oregon, USA, with maximum total plant biomass occurring at 38, 28, and 15% time submerged, respectively. However, biomass of Salicornia pacifica and Juncus balticus declined monotonically with increasing inundation. Inundation effects on the ratio of belowground to aboveground biomass varied inconsistently among species. In comparisons of field distributions with mesocosm results, B. maritimus, C. lyngbyei and J. balticus were abundant in marshes at or above elevations corresponding with their maximum productivity; however, S. foliosa and S. pacifica were frequently abundant at lower elevations corresponding with sub-optimal productivity. Our findings show species-level differences in how marsh plant growth may respond to future SLR and highlight the sensitivity of high marsh species such as S. pacifica and J. balticus to increases in flooding.

Coupling Hydrologic and Hydrodynamic Models to Estimate PMF

Science.gov (United States)

Felder, G.; Weingartner, R.

2015-12-01

Most sophisticated probable maximum flood (PMF) estimations derive the PMF from the probable maximum precipitation (PMP) by applying deterministic hydrologic models calibrated with observed data. This method is based on the assumption that the hydrological system is stationary, meaning that the system behaviour during the calibration period or the calibration event is presumed to be the same as it is during the PMF. However, as soon as a catchment-specific threshold is reached, the system is no longer stationary. At or beyond this threshold, retention areas, new flow paths, and changing runoff processes can strongly affect downstream peak discharge. These effects can be accounted for by coupling hydrologic and hydrodynamic models, a technique that is particularly promising when the expected peak discharge may considerably exceed the observed maximum discharge. In such cases, the coupling of hydrologic and hydraulic models has the potential to significantly increase the physical plausibility of PMF estimations. This procedure ensures both that the estimated extreme peak discharge does not exceed the physical limit based on riverbed capacity and that the dampening effect of inundation processes on peak discharge is considered. Our study discusses the prospect of considering retention effects on PMF estimations by coupling hydrologic and hydrodynamic models. This method is tested by forcing PREVAH, a semi-distributed deterministic hydrological model, with randomly generated, physically plausible extreme precipitation patterns. The resulting hydrographs are then used to externally force the hydraulic model BASEMENT-ETH (riverbed in 1D, potential inundation areas in 2D). Finally, the PMF estimation results obtained using the coupled modelling approach are compared to the results obtained using ordinary hydrologic modelling.

The igapó of the Negro River in central Amazonia: Linking late-successional inundation forest with fluvial geomorphology

Science.gov (United States)

Montero, Juan Carlos; Latrubesse, Edgardo M.

2013-10-01

Despite important progress on Amazonian floodplain research, the flooded forest of the Negro River "igapó" has been little investigated. In particular, no study has previously focused the linkage between fluvial geomorphology and the floristic variation across the course of the river. In this paper we describe and interpret relations between igapó forest, fluvial geomorphology and the spatial evolution of the igapó forest through the Holocene. Therefore, we investigate the effect of geomorphological units of the floodplain and channel patterns on tree diversity, composition and structural parameters of the late-successional igapó forest. Our results show that sites sharing almost identical flooding regime, exhibit variable tree assemblages, species richness and structural parameters such as basal area, tree density and tree heights, indicating a trend in which the geomorphologic styles seem to partially control the organization of igapó's tree communities. This can be also explained by the high variability of well-developed geomorphologic units in short distances and concentrated in small areas. In this dynamic the inputs from the species pool of tributary rivers play a crucial role, but also the depositional and erosional processes associated with the evolution of the floodplain during the Holocene may control floristic and structural components of the igapó forests. These results suggest that a comprehensive approach integrating floristic and geomorphologic methods is needed to understand the distribution of the complex vegetation patterns in complex floodplains such as the igapó of the Negro River. This combination of approaches may introduce a better comprehension of the temporal and spatial evolutionary analysis and a logic rationale to understand the vegetation distribution and variability in function of major landforms, soil distributions and hydrology. Thus, by integrating the past into macroecological analyses will sharpen our understanding of the

Scintillation counter, maximum gamma aspect

International Nuclear Information System (INIS)

Thumim, A.D.

1975-01-01

A scintillation counter, particularly for counting gamma ray photons, includes a massive lead radiation shield surrounding a sample-receiving zone. The shield is disassembleable into a plurality of segments to allow facile installation and removal of a photomultiplier tube assembly, the segments being so constructed as to prevent straight-line access of external radiation through the shield into radiation-responsive areas. Provisions are made for accurately aligning the photomultiplier tube with respect to one or more sample-transmitting bores extending through the shield to the sample receiving zone. A sample elevator, used in transporting samples into the zone, is designed to provide a maximum gamma-receiving aspect to maximize the gamma detecting efficiency. (U.S.)

Maximum entropy and Bayesian methods

International Nuclear Information System (INIS)

Smith, C.R.; Erickson, G.J.; Neudorfer, P.O.

1992-01-01

Bayesian probability theory and Maximum Entropy methods are at the core of a new view of scientific inference. These 'new' ideas, along with the revolution in computational methods afforded by modern computers allow astronomers, electrical engineers, image processors of any type, NMR chemists and physicists, and anyone at all who has to deal with incomplete and noisy data, to take advantage of methods that, in the past, have been applied only in some areas of theoretical physics. The title workshops have been the focus of a group of researchers from many different fields, and this diversity is evident in this book. There are tutorial and theoretical papers, and applications in a very wide variety of fields. Almost any instance of dealing with incomplete and noisy data can be usefully treated by these methods, and many areas of theoretical research are being enhanced by the thoughtful application of Bayes' theorem. Contributions contained in this volume present a state-of-the-art overview that will be influential and useful for many years to come

Microbiological Quality of Panicum maximum Grass Silage with Addition of Lactobacillus sp. as Starter

Science.gov (United States)

Sumarsih, S.; Sulistiyanto, B.; Utama, C. S.

2018-02-01

The aim of the research was to evaluate microbiological quality of Panicum maximum grass silage with addition Lactobacillus sp as starter. The completely randomized design was been used on this research with 4 treaments and 3 replications. The treatments were P0 ( Panicum maximum grass silage without addition Lactobacillus sp ), P1 ( Panicum maximum grass silage with 2% addition Lactobacillus sp), P2 (Panicum maximum grass silage with 4% addition Lactobacillus sp) and P3 (Panicum maximum grass silage with 6% addition Lactobacillus sp).The parameters were microbial populations of Panicum maximum grass silage (total lactic acid bacteria, total bacteria, total fungi, and Coliform bacteria. The data obtained were analyzed variance (ANOVA) and further tests performed Duncan’s Multiple Areas. The population of lactic acid bacteria was higher (PMicrobiological quality of Panicum maximum grass silage with addition Lactobacillus sp was better than no addition Lactobacillus sp.

Satellite microwave remote sensing of North Eurasian inundation dynamics: development of coarse-resolution products and comparison with high-resolution synthetic aperture radar data

International Nuclear Information System (INIS)

Schroeder, R; Rawlins, M A; McDonald, K C; Podest, E; Zimmermann, R; Kueppers, M

2010-01-01

Wetlands are not only primary producers of atmospheric greenhouse gases but also possess unique features that are favourable for application of satellite microwave remote sensing to monitoring their status and trend. In this study we apply combined passive and active microwave remote sensing data sets from the NASA sensors AMSR-E and QuikSCAT to map surface water dynamics over Northern Eurasia. We demonstrate our method on the evolution of large wetland complexes for two consecutive years from January 2006 to December 2007. We apply river discharge measurements from the Ob River along with land surface runoff simulations derived from the Pan-Arctic Water Balance Model during and after snowmelt in 2006 and 2007 to interpret the abundance of widespread flooding along the River Ob in early summer of 2007 observed in the remote sensing products. The coarse-resolution, 25 km, surface water product is compared to a high-resolution, 30 m, inundation map derived from ALOS PALSAR (Advanced Land Observation Satellite phased array L-band synthetic aperture radar) imagery acquired for 11 July 2006, and extending along a transect in the central Western Siberian Plain. We found that the surface water fraction derived from the combined AMSR-E/QuikSCAT data sets closely tracks the inundation mapped using higher-resolution ALOS PALSAR data.

Erosion and its rate on an accumulative Polish dune coast: the effects of the January 2012 storm surge

OpenAIRE

Łabuz, Tomasz A.

2014-01-01

The Polish coast is a non-tidal area; its shores are affected mainly by autumn-winter storm surges. Those of 6 and 14 January 2012 are representative of the forces driving the erosion of normally accumulative sections of coastal dunes, monitored by the author since 1997. The sea level maximum during these two storm surges reached 1.2 to 1.5 m amsl along the Polish coast. Land forms up to 3 m amsl were inundated. Beaches and low parts of the coast up to this height were rebuilt by sea waves at...

Estimation of Maximum Allowable PV Connection to LV Residential Power Networks

DEFF Research Database (Denmark)

Demirok, Erhan; Sera, Dezso; Teodorescu, Remus

2011-01-01

Maximum photovoltaic (PV) hosting capacity of low voltage (LV) power networks is mainly restricted by either thermal limits of network components or grid voltage quality resulted from high penetration of distributed PV systems. This maximum hosting capacity may be lower than the available solar...... potential of geographic area due to power network limitations even though all rooftops are fully occupied with PV modules. Therefore, it becomes more of an issue to know what exactly limits higher PV penetration level and which solutions should be engaged efficiently such as over sizing distribution...

Multi-Temporal Independent Component Analysis and Landsat 8 for Delineating Maximum Extent of the 2013 Colorado Front Range Flood

Directory of Open Access Journals (Sweden)

Stephen M. Chignell

2015-07-01

Full Text Available Maximum flood extent—a key data need for disaster response and mitigation—is rarely quantified due to storm-related cloud cover and the low temporal resolution of optical sensors. While change detection approaches can circumvent these issues through the identification of inundated land and soil from post-flood imagery, their accuracy can suffer in the narrow and complex channels of increasingly developed and heterogeneous floodplains. This study explored the utility of the Operational Land Imager (OLI and Independent Component Analysis (ICA for addressing these challenges in the unprecedented 2013 Flood along the Colorado Front Range, USA. Pre- and post-flood images were composited and transformed with an ICA to identify change classes. Flooded pixels were extracted using image segmentation, and the resulting flood layer was refined with cloud and irrigated agricultural masks derived from the ICA. Visual assessment against aerial orthophotography showed close agreement with high water marks and scoured riverbanks, and a pixel-to-pixel validation with WorldView-2 imagery captured near peak flow yielded an overall accuracy of 87% and Kappa of 0.73. Additional tests showed a twofold increase in flood class accuracy over the commonly used modified normalized water index. The approach was able to simultaneously distinguish flood-related water and soil moisture from pre-existing water bodies and other spectrally similar classes within the narrow and braided channels of the study site. This was accomplished without the use of post-processing smoothing operations, enabling the important preservation of nuanced inundation patterns. Although flooding beneath moderate and sparse riparian vegetation canopy was captured, dense vegetation cover and paved regions of the floodplain were main sources of omission error, and commission errors occurred primarily in pixels of mixed land use and along the flood edge. Nevertheless, the unsupervised nature of ICA

Impact of contaminants on aquatic systems and inundated sites with respect to flood events - In vitro biotests, chemical target analysis and fractionation methods

OpenAIRE

Wölz, Jan

2009-01-01

Scope of the present study is the development and application of aquatic in vitro bioassays and methods of effect-directed analysis (EDA). It aims at investigating contamination of suspended particulate matter (SPM) and pollution of inundated sites and riparian aquifer, respectively. In the first part of this study, SPM was sampled during flood events and toxicological activities were determined. The second part of the study dealt with possible conflict of interests between flood management (...

Urban floods: a case study in the Savigliano area (North-Western Italy

Directory of Open Access Journals (Sweden)

C. Audisio

2011-11-01

Full Text Available Flood processes and effects are examined, concerning two rivers in an urbanized area in North-Western Italy (Piedmont – Cuneo Plain. In May 2008, some areas in Northern Italy were struck by intense and persistent rainfall. In the Cuneo province (Southern Piedmont, floodplain with some urban areas was inundated over ca. ten square kilometres, and the city of Savigliano (about 21 000 inhabitants was particularly hit by flood. A purposely-made historical research has evidenced approximately fifty flood events as having occurred since 1350 in the Savigliano area. Based upon historical data, both documents and maps, GIS (Geographical Information System technique and field surveys were used to quantitatively assess the growing urbanization of the city and to describe flood processes and effects over years. This work aims to describe the dynamic behaviour of the 2008 flood, also comparing it to past events, in particular those that occurred in 1896. It is emphasized how the knowledge of past events can be helpful in reducing urban flooding.

Flood risk assessment through 1D/2D couple HEC-RAS hydrodynamic modeling- A case study of Surat City, Lower Tapi Basin, India

Science.gov (United States)

Patel, Dhruvesh; Ramirez, Jorge; Srivastava, Prashant; Bray, Michaela; Han, Dawei

2017-04-01

Surat, known as the diamond city of Gujart is situated 100 km downstream of Ukai dam and near the mouth of river Tapi and affected by the flood at every alternate year. The city experienced catastrophic floods in 1933, 1959, 1968, 1970, 1994, 1998 and 2006. It is estimated that a single flood event during August 6-12, 2006 in Surat and Hazira twin-city, caused heavy damages, resulted in the death of 300 people and property damage worth € 289 million. The peak discharge of 25768 m3 s-1 release from Ukai dam was responsible for the disastrous flood in Surat city. To identifylow lying areas prone to inundation and reduce the uncertainty in flood mitigation measures, HEC-RAS based 1D/2D Couple hydrodynamic modeling is carried out for Surat city. Release from the Ukai dam and tidal level of the sea are considered for upstream and downstream boundary condition. 299 surveyed cross-sections have been considered for 1D modeling, whereas a topographic map at 0.5 m contour interval was used to produce a 5 m grid and SRTM (30 & 90 m) grid has been considered for Suart and Lower Tapi Basin (LTB). Flow is simulated under unsteady conditions, calibrated for the year 1998 and validated for the year 2006. The simulated result shows that the 9th August 18.00 hr was the worst day for Surat city and maximum 75-77 % area was under inundation. Most of the flooded area experienced 0.25 m/s water velocity with the duration of 90 hr. Due to low velocity and high duration of the flood, a low lying area within the west zone and south-west zone of the city was badly affected by the flood, whereas the south zone and south-east zone was least. Simulated results show good correlation when compared with an observed flood level map. The simulated results will be helpful to improve the flood resilience strategy at Surat city and reduce the uncertainty for flood inundation mapping for future dam releases. The present case study shows the applicability of 1D/2D coupled hydrodynamic modeling for

Flood Modeling Using a Synthesis of Multi-Platform LiDAR Data

Directory of Open Access Journals (Sweden)

Ryan M. Csontos

2013-09-01

Full Text Available This study examined the utility of a high resolution ground-based (mobile and terrestrial Light Detection and Ranging (LiDAR dataset (0.2 m point-spacing supplemented with a coarser resolution airborne LiDAR dataset (5 m point-spacing for use in a flood inundation analysis. The techniques for combining multi-platform LiDAR data into a composite dataset in the form of a triangulated irregular network (TIN are described, and quantitative comparisons were made to a TIN generated solely from the airborne LiDAR dataset. For example, a maximum land surface elevation difference of 1.677 m and a mean difference of 0.178 m were calculated between the datasets based on sample points. Utilizing the composite and airborne LiDAR-derived TINs, a flood inundation comparison was completed using a one-dimensional steady flow hydraulic modeling analysis. Quantitative comparisons of the water surface profiles and depth grids indicated an underestimation of flooding extent, volume, and maximum flood height using the airborne LiDAR data alone. A 35% increase in maximum flood height was observed using the composite LiDAR dataset. In addition, the extents of the water surface profiles generated from the two datasets were found to be statistically significantly different. The urban and mountainous characteristics of the study area as well as the density (file size of the high resolution ground based LiDAR data presented both opportunities and challenges for flood modeling analyses.

Urban Flood Mapping Based on Unmanned Aerial Vehicle Remote Sensing and Random Forest Classifier—A Case of Yuyao, China

Directory of Open Access Journals (Sweden)

Quanlong Feng

2015-03-01

Full Text Available Flooding is a severe natural hazard, which poses a great threat to human life and property, especially in densely-populated urban areas. As one of the fastest developing fields in remote sensing applications, an unmanned aerial vehicle (UAV can provide high-resolution data with a great potential for fast and accurate detection of inundated areas under complex urban landscapes. In this research, optical imagery was acquired by a mini-UAV to monitor the serious urban waterlogging in Yuyao, China. Texture features derived from gray-level co-occurrence matrix were included to increase the separability of different ground objects. A Random Forest classifier, consisting of 200 decision trees, was used to extract flooded areas in the spectral-textural feature space. Confusion matrix was used to assess the accuracy of the proposed method. Results indicated the following: (1 Random Forest showed good performance in urban flood mapping with an overall accuracy of 87.3% and a Kappa coefficient of 0.746; (2 the inclusion of texture features improved classification accuracy significantly; (3 Random Forest outperformed maximum likelihood and artificial neural network, and showed a similar performance to support vector machine. The results demonstrate that UAV can provide an ideal platform for urban flood monitoring and the proposed method shows great capability for the accurate extraction of inundated areas.

Flow area optimization in point to area or area to point flows

International Nuclear Information System (INIS)

Ghodoossi, Lotfollah; Egrican, Niluefer

2003-01-01

This paper deals with the constructal theory of generation of shape and structure in flow systems connecting one point to a finite size area. The flow direction may be either from the point to the area or the area to the point. The formulation of the problem remains the same if the flow direction is reversed. Two models are used in optimization of the point to area or area to point flow problem: cost minimization and revenue maximization. The cost minimization model enables one to predict the shape of the optimized flow areas, but the geometric sizes of the flow areas are not predictable. That is, as an example, if the area of flow is a rectangle with a fixed area size, optimization of the point to area or area to point flow problem by using the cost minimization model will only predict the height/length ratio of the rectangle not the height and length itself. By using the revenue maximization model in optimization of the flow problems, all optimized geometric aspects of the interested flow areas will be derived as well. The aim of this paper is to optimize the point to area or area to point flow problems in various elemental flow area shapes and various structures of the flow system (various combinations of elemental flow areas) by using the revenue maximization model. The elemental flow area shapes used in this paper are either rectangular or triangular. The forms of the flow area structure, made up of an assembly of optimized elemental flow areas to obtain bigger flow areas, are rectangle-in-rectangle, rectangle-in-triangle, triangle-in-triangle and triangle-in-rectangle. The global maximum revenue, revenue collected per unit flow area and the shape and sizes of each flow area structure have been derived in optimized conditions. The results for each flow area structure have been compared with the results of the other structures to determine the structure that provides better performance. The conclusion is that the rectangle-in-triangle flow area structure

SLR-induced changes on storm flooding in coastal areas: the role of accommodation space

Science.gov (United States)

Jiménez, Jose A.; Dockx, Stijn; Monbaliu, Jaak

2015-04-01

Most of existing predictions of climate-induce changes in coastal storminess in the Mediterranean indicate the absence of any significant increasing trend in neither wave height nor surge. However, this does not mean that magnitude and/or frequency of storm-induced coastal hazards will not be affected by climate change. Thus, sea level rise will induce a series of long-term changes in coastal areas that although not directly affecting storminess will interact with storm-induced processes and, thus, changing coastal storm risks. A typical approach to account SLR-induced effects on coastal inundation by storms is to modify present water level extreme climate by adding expected MWL increase. This implies to consider the coast as a static and passive system to SLR maintaining its configuration from actual to projected (rised) sea level and, as a result of this, the frequency of flood events should increase and, the magnitude of flooding associated to a probability of occurrence will also increase. This will only be realistic for really passive or rigid coasts. However, sandy coastlines will response to SLR and, thus, this approach should undervalue coastal resilience. Within this context, the main aim of this work is to propose a method to assess the effects of SLR on the magnitude of storm-induced coastal flooding on sandy coastlines taking into account their capacity of response. It combines the use of a inundation model (LISFLOOD-FP) for delineating the flood-prone area for given storm conditions and, a coastal module to account for SLR-induced changes in the coastal fringe. The method assumes an equilibrium-type coastal response to SLR which, ideally, implies that the beach profile will be reconstructed under the new higher water level, in such a way that the relative beach configuration will be the same. However, this should only be possible provided there is enough accommodation space in the hinterland. In most of developed coasts, the existence of human built

Exercise-induced maximum metabolic rate scaled to body mass by ...

African Journals Online (AJOL)

user

2016-10-27

Oct 27, 2016 ... maximum aerobic metabolic rate (MMR) is proportional to the fractal extent ... metabolic rate with body mass can be obtained by taking body .... blood takes place. ..... MMR and BMR is that MMR is owing mainly to respiration in skeletal .... the spectra of surface area scaling strategies of cells and organisms:.

Uni- and multi-variable modelling of flood losses: experiences gained from the Secchia river inundation event.

Science.gov (United States)

Carisi, Francesca; Domeneghetti, Alessio; Kreibich, Heidi; Schröter, Kai; Castellarin, Attilio

2017-04-01

Flood risk is function of flood hazard and vulnerability, therefore its accurate assessment depends on a reliable quantification of both factors. The scientific literature proposes a number of objective and reliable methods for assessing flood hazard, yet it highlights a limited understanding of the fundamental damage processes. Loss modelling is associated with large uncertainty which is, among other factors, due to a lack of standard procedures; for instance, flood losses are often estimated based on damage models derived in completely different contexts (i.e. different countries or geographical regions) without checking its applicability, or by considering only one explanatory variable (i.e. typically water depth). We consider the Secchia river flood event of January 2014, when a sudden levee-breach caused the inundation of nearly 200 km2 in Northern Italy. In the aftermath of this event, local authorities collected flood loss data, together with additional information on affected private households and industrial activities (e.g. buildings surface and economic value, number of company's employees and others). Based on these data we implemented and compared a quadratic-regression damage function, with water depth as the only explanatory variable, and a multi-variable model that combines multiple regression trees and considers several explanatory variables (i.e. bagging decision trees). Our results show the importance of data collection revealing that (1) a simple quadratic regression damage function based on empirical data from the study area can be significantly more accurate than literature damage-models derived for a different context and (2) multi-variable modelling may outperform the uni-variable approach, yet it is more difficult to develop and apply due to a much higher demand of detailed data.

STUDY ON IMPACT OF SALINE WATER INUNDATION ON FRESHWATER AQUACULTURE IN SUNDARBAN USING RISK ANALYSIS TOOLS

Directory of Open Access Journals (Sweden)

B.K Chand

2012-11-01

Full Text Available The impact of saline water inundation on freshwater aquaculture was evaluated through risk assessment tools. Fishponds in low-lying areas of Sagar and Basanti block are prone to saline water flooding. Respondents of Sagar block considered events like cyclone and coastal flooding as extreme risk; erratic monsoon, storm surge and land erosion as high risk; temperature rise, sea level rise, hot & extended summer and precipitation as medium risk. Likewise, in Basanti block the respondents rated cyclone as extreme risk; erratic monsoon, storm surge as high risk; temperature rise, hot & extended summer, land erosion, and precipitation as medium risk; coastal flooding and sea level rise as low risk. Fish farmers of Sagar block classified the consequences of saline water flooding like breach of pond embankment and mass mortality of fishes as extreme risk; escape of existing fish stock and diseases as high risk; entry of unwanted species, retardation of growth and deterioration of water quality as medium risk; and damage of pond environment as low risk. Farmers of Basanti block categorised breach of pond dyke, mass mortality of fishes and entry of unwanted species as extreme risk; escape of fish and diseases as high risk; retardation of growth as medium risk; deterioration of water quality and damage of pond environment as low risk. To reduce the threats against saline water ingression, farmers are taking some coping measures like increase in pond dyke height; repair and strengthening of dyke; plantation on dyke; dewatering and addition of fresh water; application of chemicals/ lime/ dung; addition of tree branches in pond for hide outs etc.

Maximum power point tracking: a cost saving necessity in solar energy systems

Energy Technology Data Exchange (ETDEWEB)

Enslin, J H.R. [Stellenbosch Univ. (South Africa). Dept. of Electrical and Electronic Engineering

1992-12-01

A well engineered renewable remote energy system, utilizing the principal of Maximum Power Point Tracking (MPPT) can improve cost effectiveness, has a higher reliability and can improve the quality of life in remote areas. A high-efficient power electronic converter, for converting the output voltage of a solar panel, or wind generator, to the required DC battery bus voltage has been realized. The converter is controlled to track the maximum power point of the input source under varying input and output parameters. Maximum power point tracking for relative small systems is achieved by maximization of the output current in a battery charging regulator, using an optimized hill-climbing, inexpensive microprocessor based algorithm. Through practical field measurements it is shown that a minimum input source saving of between 15 and 25% on 3-5 kWh/day systems can easily be achieved. A total cost saving of at least 10-15% on the capital cost of these systems are achievable for relative small rating Remote Area Power Supply (RAPS) systems. The advantages at large temperature variations and high power rated systems are much higher. Other advantages include optimal sizing and system monitor and control. (author).

GIS-based maps and area estimates of Northern Hemisphere permafrost extent during the Last Glacial Maximum

NARCIS (Netherlands)

Lindgren, A.; Hugelius, G.; Kuhry, P.; Christensen, T.R.; Vandenberghe, J.F.

2016-01-01

This study presents GIS-based estimates of permafrost extent in the northern circumpolar region during the Last Glacial Maximum (LGM), based on a review of previously published maps and compilations of field evidence in the form of ice-wedge pseudomorphs and relict sand wedges. We focus on field

Cosmic shear measurement with maximum likelihood and maximum a posteriori inference

Science.gov (United States)

Hall, Alex; Taylor, Andy

2017-06-01

We investigate the problem of noise bias in maximum likelihood and maximum a posteriori estimators for cosmic shear. We derive the leading and next-to-leading order biases and compute them in the context of galaxy ellipticity measurements, extending previous work on maximum likelihood inference for weak lensing. We show that a large part of the bias on these point estimators can be removed using information already contained in the likelihood when a galaxy model is specified, without the need for external calibration. We test these bias-corrected estimators on simulated galaxy images similar to those expected from planned space-based weak lensing surveys, with promising results. We find that the introduction of an intrinsic shape prior can help with mitigation of noise bias, such that the maximum a posteriori estimate can be made less biased than the maximum likelihood estimate. Second-order terms offer a check on the convergence of the estimators, but are largely subdominant. We show how biases propagate to shear estimates, demonstrating in our simple set-up that shear biases can be reduced by orders of magnitude and potentially to within the requirements of planned space-based surveys at mild signal-to-noise ratio. We find that second-order terms can exhibit significant cancellations at low signal-to-noise ratio when Gaussian noise is assumed, which has implications for inferring the performance of shear-measurement algorithms from simplified simulations. We discuss the viability of our point estimators as tools for lensing inference, arguing that they allow for the robust measurement of ellipticity and shear.

Fate of 90Sr and U(VI) in Dounreay sediments following saline inundation and erosion.

Science.gov (United States)

Eagling, Jane; Worsfold, Paul J; Blake, William H; Keith-Roach, Miranda J

2013-08-01

There is concern that sea level rise associated with projected climate change will lead to the inundation, flooding and erosion of soils and sediments contaminated with radionuclides at coastal nuclear sites, such as Dounreay (UK), with seawater. Here batch and column experiments were designed to simulate these scenarios and sequential extractions were used to identify the key radionuclide solid phase associations. Strontium was exchangeable and was mobilised rapidly by ion exchange with seawater Mg(2+) in both batch and column experiments. In contrast, U was more strongly bound to the sediments and mobilisation was initially limited by the influence of the sediment on the pH of the water. Release was only observed when the pH increased above 6.9, suggesting that the formation of soluble U(VI)-carbonate species was important. Under dynamic flow conditions, long term release was significant (47%), but controlled by slow desorption kinetics from a range of binding sites. Copyright © 2013 Elsevier Ltd. All rights reserved.

Lahar inundated, modified, and preserved 1.88 Ma early hominin (OH24 and OH56) Olduvai DK site.

Science.gov (United States)

Stanistreet, I G; Stollhofen, H; Njau, J K; Farrugia, P; Pante, M C; Masao, F T; Albert, R M; Bamford, M K

2018-03-01

Archaeological excavations at the DK site in the eastern Olduvai Basin, Tanzania, age-bracketed between ∼1.88 Ma (Bed I Basalt) and ∼1.85 Ma (Tuff IB), record the oldest lahar inundation, modification, and preservation of a hominin "occupation" site yet identified. Our landscape approach reconstructs environments and processes at high resolution to explain the distribution and final preservation of archaeological materials at the DK site, where an early hominin (likely Homo habilis) assemblage of stone tools and bones, found close to hominin specimens OH24 and OH56, developed on an uneven heterogeneous surface that was rapidly inundated by a lahar and buried to a depth of 0.4-1.2 m (originally ∼1.0-2.4 m pre-compaction). The incoming intermediate to high viscosity mudflow selectively modified the original accumulation of "occupation debris," so that it is no longer confined to the original surface. A dispersive debris "halo" was identified within the lahar deposit: debris is densest immediately above the site, but tails off until not present >150 m laterally. Voorhies indices and metrics derived from limb bones are used to define this dispersive halo spatially and might indicate a possible second assemblage to the east that is now eroded away. Based upon our new data and prior descriptions, two possibilities for the OH24 skull are suggested: it was either entrained by the mudflow from the DK surface and floated due to lower density toward its top, or it was deposited upon the solid top surface after its consolidation. Matrix adhering to material found in association with the parietals indicates that OH56 at least was relocated by the mudflow. Copyright © 2017 Elsevier Ltd. All rights reserved.

The Role of Near-Shore Bathymetry During Tsunami Inundation in a Reef Island Setting: A Case Study of Tutuila Island

Science.gov (United States)

Dilmen, Derya I.; Roe, Gerard H.; Wei, Yong; Titov, Vasily V.

2018-04-01

On September 29, 2009 at 17:48 UTC, an M w = 8.1 earthquake in the Tonga Trench generated a tsunami that caused heavy damage across Samoa, American Samoa, and Tonga. One of the worst hits was the volcanic island of Tutuila in American Samoa. Tutuila has a typical tropical island bathymetry setting influenced by coral reefs, and so the event provided an opportunity to evaluate the relationship between tsunami dynamics and the bathymetry in that typical island environment. Previous work has come to differing conclusions regarding how coral reefs affect tsunami dynamics through their influence on bathymetry and dissipation. This study presents numerical simulations of this event with a focus on two main issues: first, how roughness variations affect tsunami run-up and whether different values of Manning's roughness parameter, n, improve the simulated run-up compared to observations; and second, how depth variations in the shelf bathymetry with coral reefs control run-up and inundation on the island coastlines they shield. We find that no single value of n provides a uniformly good match to all observations; and we find substantial bay-to-bay variations in the impact of varying n. The results suggest that there are aspects of tsunami wave dissipation which are not captured by a simplified drag formulation used in shallow-water waves model. The study also suggests that the primary impact of removing the near-shore bathymetry in coral reef environment is to reduce run-up, from which we conclude that, at least in this setting, the impact of the near-shore bathymetry is to increase run-up and inundation.

The Role of Near-Shore Bathymetry During Tsunami Inundation in a Reef Island Setting: A Case Study of Tutuila Island

Science.gov (United States)

Dilmen, Derya I.; Roe, Gerard H.; Wei, Yong; Titov, Vasily V.

2018-02-01

On September 29, 2009 at 17:48 UTC, an M w = 8.1 earthquake in the Tonga Trench generated a tsunami that caused heavy damage across Samoa, American Samoa, and Tonga. One of the worst hits was the volcanic island of Tutuila in American Samoa. Tutuila has a typical tropical island bathymetry setting influenced by coral reefs, and so the event provided an opportunity to evaluate the relationship between tsunami dynamics and the bathymetry in that typical island environment. Previous work has come to differing conclusions regarding how coral reefs affect tsunami dynamics through their influence on bathymetry and dissipation. This study presents numerical simulations of this event with a focus on two main issues: first, how roughness variations affect tsunami run-up and whether different values of Manning's roughness parameter, n, improve the simulated run-up compared to observations; and second, how depth variations in the shelf bathymetry with coral reefs control run-up and inundation on the island coastlines they shield. We find that no single value of n provides a uniformly good match to all observations; and we find substantial bay-to-bay variations in the impact of varying n. The results suggest that there are aspects of tsunami wave dissipation which are not captured by a simplified drag formulation used in shallow-water waves model. The study also suggests that the primary impact of removing the near-shore bathymetry in coral reef environment is to reduce run-up, from which we conclude that, at least in this setting, the impact of the near-shore bathymetry is to increase run-up and inundation.

Contamination of community water sources by potentially pathogenic vibrios following sea water inundation.

Science.gov (United States)

Kanungo, Reba; Shashikala; Karunasagar, I; Srinivasan, S; Sheela, Devi; Venkatesh, K; Anitha, P

2007-12-01

Potentially pathogenic members of the Vibrionaceae family including Vibrio cholerae and Vibrio parahemolyticus were isolated from domestic sources of drinking water in coastal villages following sea water inundation during the tsunami in Southern India. Phenotypic and genotypic studies were done to confirm the identity and detection of toxins. Vibrio-gyr (gyrase B gene) was detected in all sixteen vibrio isolates. Toxin regulating genes i.e.: ctx gene, tdh gene, and trh gene, however were not detected in any of the strains, thereby ruling out presence of toxins which could endanger human life. Other potentially pathogenic bacteria Aeromonas and Plesiomonas were also isolated from hand pumps and wells, in a few localities. There was no immediate danger in the form of an outbreak or sporadic gastroenteritis at the time of the study. Timely chlorination and restoration of potable water supply to the flood affected population by governmental and nongovernmental agencies averted waterborne gastroenteritis. Assessment of quality of water and detection of potential virulent organisms is an important public health activity following natural disasters. This work highlights the importance of screening water sources for potentially pathogenic microorganisms after natural disasters to avert outbreaks of gastroenteritis and other infectious diseases.

Flood of September 22, 1998, in Arecibo and Utuado, Puerto Rico

Science.gov (United States)

Torres-Sierra, Heriberto

2002-01-01

Hurricane Georges made landfall on the southeastern part of Puerto Rico during September 21, 1998. Georges, with maximum sustained winds of 185 kilometers per hour and gusts to 240 kilometers per hour, produced 24-hour total rainfall amounts of 770 millimeters on the island's mountainous interior. Severe flooding affected almost half of the island's 78 municipios during September 21-22, 1998. The most affected municipios were Adjuntas, Aguada, Aguadilla, A?asco, Arecibo, Cayey, Ciales, Comerio, Barceloneta, Dorado, Jayuya, Manati, Mayaguez, Morovis, Orocovis, Patillas, Toa Alta, Toa Baja, and Utuado. The combination of strong winds, intense rainfall and severe flooding caused widespread property damages. More than 20,000 houses were destroyed and more than 100,000 houses sustained damage. Floodwaters and landslides destroyed or damaged many bridges and roads throughout the island. Records indicate that Hurricane Georges induced flood discharges in the Rio Grande de Arecibo Basin that were the largest on record. Floodwaters inundated urban and rural areas, affecting urban subdivisions, businesses, vehicles, bridges, roads, and high-tension electric power lines. To define the extent and depth of inundation, more than 280 high-water marks were identified and surveyed in Arecibo and Utuado. In addition estimates of flood magnitude and frequency were made at selected gaging stations, and flood profiles were developed for certain stream reaches. Flooding was most severe in the towns of Arecibo and Utuado. In Arecibo, the most affected communities were the rural area of San Francisco, the urban subdivisions of Martell, Nolla, and Arecibo Gardens, and the low-lying areas of downtown Arecibo. In these areas, the water depths ranged from 0.6 to 1.8 meters. In Utuado, floodwaters from the Rio Vivi and the Rio Grande de Arecibo inundated the downtown area affecting homes, public facilities, and businesses. In the urban subdivision of Jesus Maria Lago, the depth of flooding

Maximum Acceleration Recording Circuit

Science.gov (United States)

Bozeman, Richard J., Jr.

1995-01-01

Coarsely digitized maximum levels recorded in blown fuses. Circuit feeds power to accelerometer and makes nonvolatile record of maximum level to which output of accelerometer rises during measurement interval. In comparison with inertia-type single-preset-trip-point mechanical maximum-acceleration-recording devices, circuit weighs less, occupies less space, and records accelerations within narrower bands of uncertainty. In comparison with prior electronic data-acquisition systems designed for same purpose, circuit simpler, less bulky, consumes less power, costs and analysis of data recorded in magnetic or electronic memory devices. Circuit used, for example, to record accelerations to which commodities subjected during transportation on trucks.

Neutron spectra unfolding with maximum entropy and maximum likelihood

International Nuclear Information System (INIS)

Itoh, Shikoh; Tsunoda, Toshiharu

1989-01-01

A new unfolding theory has been established on the basis of the maximum entropy principle and the maximum likelihood method. This theory correctly embodies the Poisson statistics of neutron detection, and always brings a positive solution over the whole energy range. Moreover, the theory unifies both problems of overdetermined and of underdetermined. For the latter, the ambiguity in assigning a prior probability, i.e. the initial guess in the Bayesian sense, has become extinct by virtue of the principle. An approximate expression of the covariance matrix for the resultant spectra is also presented. An efficient algorithm to solve the nonlinear system, which appears in the present study, has been established. Results of computer simulation showed the effectiveness of the present theory. (author)

Maximum Power from a Solar Panel

Directory of Open Access Journals (Sweden)

Michael Miller

2010-01-01

Full Text Available Solar energy has become a promising alternative to conventional fossil fuel sources. Solar panels are used to collect solar radiation and convert it into electricity. One of the techniques used to maximize the effectiveness of this energy alternative is to maximize the power output of the solar collector. In this project the maximum power is calculated by determining the voltage and the current of maximum power. These quantities are determined by finding the maximum value for the equation for power using differentiation. After the maximum values are found for each time of day, each individual quantity, voltage of maximum power, current of maximum power, and maximum power is plotted as a function of the time of day.