Crustal seismicity and the earthquake catalog maximum moment magnitude (Mcmax) in stable continental regions (SCRs): Correlation with the seismic velocity of the lithosphere

Science.gov (United States)

Mooney, Walter D.; Ritsema, Jeroen; Hwang, Yong Keun

2012-12-01

A joint analysis of global seismicity and seismic tomography indicates that the seismic potential of continental intraplate regions is correlated with the seismic properties of the lithosphere. Archean and Early Proterozoic cratons with cold, stable continental lithospheric roots have fewer crustal earthquakes and a lower maximum earthquake catalog moment magnitude (Mcmax). The geographic distribution of thick lithospheric roots is inferred from the global seismic model S40RTS that displays shear-velocity perturbations (δVS) relative to the Preliminary Reference Earth Model (PREM). We compare δVS at a depth of 175 km with the locations and moment magnitudes (Mw) of intraplate earthquakes in the crust (Schulte and Mooney, 2005). Many intraplate earthquakes concentrate around the pronounced lateral gradients in lithospheric thickness that surround the cratons and few earthquakes occur within cratonic interiors. Globally, 27% of stable continental lithosphere is underlain by δVS≥3.0%, yet only 6.5% of crustal earthquakes with Mw>4.5 occur above these regions with thick lithosphere. No earthquakes in our catalog with Mw>6 have occurred above mantle lithosphere with δVS>3.5%, although such lithosphere comprises 19% of stable continental regions. Thus, for cratonic interiors with seismically determined thick lithosphere (1) there is a significant decrease in the number of crustal earthquakes, and (2) the maximum moment magnitude found in the earthquake catalog is Mcmax=6.0. We attribute these observations to higher lithospheric strength beneath cratonic interiors due to lower temperatures and dehydration in both the lower crust and the highly depleted lithospheric root.

Quantitative monitoring of CO2 injection at Sleipner using seismic full waveform inversion in the time lapse mode and rock physics modeling

International Nuclear Information System (INIS)

Queisser, M.P.

2012-01-01

saturations as well as to generate pseudo well logs to estimate confidence intervals of the inverted parameters. The rock physics modeling has been used to relate inverted parameters to CO 2 saturations. The injected CO 2 is buoyant. The highest CO 2 saturations are in the upper half of the storage reservoir, but not necessarily at the top. Non-uniqueness of the saturation maps associated with the density scenario has been assessed. As a result, the distribution of the maximum saturation values remains the same. The quantity of dissolved CO 2 in the reservoir water is a key parameter from both a security and optimization point of view. A quantitative estimation of dissolved CO 2 by seismic means has not been undertaken yet to our knowledge. Based on the seismic inversion result of a seismic line, I found that along the line at least 20% of the injected CO 2 mass was dissolved in 2006, after 10 years of injection. Such a high value indicates enhanced solubility trapping, which is very advantageous for storage safety at Sleipner. The results of this work represent a further step towards ultimate goals of quantitative monitoring, such as the estimation of the injected CO 2 in-situ volume. (author)

Predicting the Maximum Earthquake Magnitude from Seismic Data in Israel and Its Neighboring Countries.

Science.gov (United States)

Last, Mark; Rabinowitz, Nitzan; Leonard, Gideon

2016-01-01

This paper explores several data mining and time series analysis methods for predicting the magnitude of the largest seismic event in the next year based on the previously recorded seismic events in the same region. The methods are evaluated on a catalog of 9,042 earthquake events, which took place between 01/01/1983 and 31/12/2010 in the area of Israel and its neighboring countries. The data was obtained from the Geophysical Institute of Israel. Each earthquake record in the catalog is associated with one of 33 seismic regions. The data was cleaned by removing foreshocks and aftershocks. In our study, we have focused on ten most active regions, which account for more than 80% of the total number of earthquakes in the area. The goal is to predict whether the maximum earthquake magnitude in the following year will exceed the median of maximum yearly magnitudes in the same region. Since the analyzed catalog includes only 28 years of complete data, the last five annual records of each region (referring to the years 2006-2010) are kept for testing while using the previous annual records for training. The predictive features are based on the Gutenberg-Richter Ratio as well as on some new seismic indicators based on the moving averages of the number of earthquakes in each area. The new predictive features prove to be much more useful than the indicators traditionally used in the earthquake prediction literature. The most accurate result (AUC = 0.698) is reached by the Multi-Objective Info-Fuzzy Network (M-IFN) algorithm, which takes into account the association between two target variables: the number of earthquakes and the maximum earthquake magnitude during the same year.

Seismicity and Tectonics of the West Kaibab Fault Zone, AZ

Science.gov (United States)

Wilgus, J. T.; Brumbaugh, D. S.

2014-12-01

The West Kaibab Fault Zone (WKFZ) is the westernmost bounding structure of the Kaibab Plateau of northern Arizona. The WKFZ is a branching complex of high angle, normal faults downthrown to the west. There are three main faults within the WKFZ, the Big Springs fault with a maximum of 165 m offset, the Muav fault with 350 m of displacement, and the North Road fault having a maximum throw of approximately 90 m. Mapping of geologically recent surface deposits at or crossing the fault contacts indicates that the faults are likely Quaternary with the most recent offsets occurring one of the most seismically active areas in Arizona and lies within the Northern Arizona Seismic Belt (NASB), which stretches across northern Arizona trending NW-SE. The data set for this study includes 156 well documented events with the largest being a M5.75 in 1959 and including a swarm of seven earthquakes in 2012. The seismic data set (1934-2014) reveals that seismic activity clusters in two regions within the study area, the Fredonia cluster located in the NW corner of the study area and the Kaibab cluster located in the south central portion of the study area. The fault plane solutions to date indicate NE-SW to EW extension is occurring in the study area. Source relationships between earthquakes and faults within the WKFZ have not previously been studied in detail. The goal of this study is to use the seismic data set, the available data on faults, and the regional physiography to search for source relationships for the seismicity. Analysis includes source parameters of the earthquake data (location, depth, and fault plane solutions), and comparison of this output to the known faults and areal physiographic framework to indicate any active faults of the WKFZ, or suggested active unmapped faults. This research contributes to a better understanding of the present nature of the WKFZ and the NASB as well.

Asymptotic Co- and Post-seismic displacements in a homogeneous Maxwell sphere

Science.gov (United States)

Tang, He; Sun, Wenke

2018-05-01

The deformations of the Earth caused by internal and external forces are usually expressed through Green's functions or the superposition of normal modes, i.e. via numerical methods, which are applicable for computing both co- and post-seismic deformations. It is difficult to express these deformations in an analytical form, even for a uniform viscoelastic sphere. In this study, we present a set of asymptotic solutions for computing co- and post-seismic displacements; these solutions can be further applied to solving co- and post-seismic geoid, gravity, and strain changes. Expressions are derived for a uniform Maxwell Earth by combining the reciprocity theorem, which links earthquake, tidal, shear and loading deformations, with the asymptotic solutions of these three external forces (tidal, shear and loading) and analytical inverse Laplace transformation formulae. Since the asymptotic solutions are given in a purely analytical form without series summations or extra convergence skills, they can be practically applied in an efficient way, especially when computing post-seismic deformations and glacial isotactic adjustments of the Earth over long timescales.

Amplitude versus offset analysis to marine seismic data acquired in Nankai Trough, offshore Japan where methane hydrate exists

Science.gov (United States)

Hato, M.; Inamori, T.; Matsuoka, T.; Shimizu, S.

2003-04-01

Occurrence of methane hydrates in the Nankai Trough, located off the south-eastern coast of Japan, was confirmed by the exploratory test well drilling conducted by Japan’s Ministry of International Trade and Industry in 1999. Confirmation of methane hydrate has given so big impact to the Japan's future energy strategy and scientific and technological interest was derived from the information of the coring and logging results at the well. Following the above results, Japan National Oil Corporation (JNOC) launched the national project, named as MH21, for establishing the technology of methane hydrate exploration and related technologies such as production and development. As one of the research project for evaluating the total amount of the methane hydrate, Amplitude versus Offset (AVO) was applied to the seismic data acquired in the Nankai Trough area. The main purpose of the AVO application is to evaluate the validity of delineation of methane hydrate-bearing zones. Since methane hydrate is thought to accompany with free-gas in general just below the methane hydrate-bearing zones, the AVO has a possibility of describing the presence of free-gas. The free-gas is thought to be located just below the base of methane hydrate stability zone which is characterized by the Bottom Simulating Reflectors (BSRs) on the seismic section. In this sense, AVO technology, which was developed as gas delineation tools, can be utilized for methane hydrate exploration. The result of AVO analysis clearly shows gas-related anomaly below the BSRs. Appearance of the AVO anomaly has so wide variety. Some of the anomalies might not correspond to the free-gas existence, however, some of them may show free-gas. We are now going to develop methodology to clearly discriminate free-gas from non-gas zone by integrating various types of seismic methods such as seismic inversion and seismic attribute analysis.

Geomechanical Modeling of Fault Responses and the Potential for Notable Seismic Events during Underground CO2 Injection

Science.gov (United States)

Rutqvist, J.; Cappa, F.; Mazzoldi, A.; Rinaldi, A.

2012-12-01

The importance of geomechanics associated with large-scale geologic carbon storage (GCS) operations is now widely recognized. There are concerns related to the potential for triggering notable (felt) seismic events and how such events could impact the long-term integrity of a CO2 repository (as well as how it could impact the public perception of GCS). In this context, we review a number of modeling studies and field observations related to the potential for injection-induced fault reactivations and seismic events. We present recent model simulations of CO2 injection and fault reactivation, including both aseismic and seismic fault responses. The model simulations were conducted using a slip weakening fault model enabling sudden (seismic) fault rupture, and some of the numerical analyses were extended to fully dynamic modeling of seismic source, wave propagation, and ground motion. The model simulations illustrated what it will take to create a magnitude 3 or 4 earthquake that would not result in any significant damage at the groundsurface, but could raise concerns in the local community and could also affect the deep containment of the stored CO2. The analyses show that the local in situ stress field, fault orientation, fault strength, and injection induced overpressure are critical factors in determining the likelihood and magnitude of such an event. We like to clarify though that in our modeling we had to apply very high injection pressure to be able to intentionally induce any fault reactivation. Consequently, our model simulations represent extreme cases, which in a real GCS operation could be avoided by estimating maximum sustainable injection pressure and carefully controlling the injection pressure. In fact, no notable seismic event has been reported from any of the current CO2 storage projects, although some unfelt microseismic activities have been detected by geophones. On the other hand, potential future commercial GCS operations from large power plants

A sensitivity analysis on seismic tomography data with respect to CO2 saturation of a CO2 geological sequestration field

Science.gov (United States)

Park, Chanho; Nguyen, Phung K. T.; Nam, Myung Jin; Kim, Jongwook

2013-04-01

Monitoring CO2 migration and storage in geological formations is important not only for the stability of geological sequestration of CO2 but also for efficient management of CO2 injection. Especially, geophysical methods can make in situ observation of CO2 to assess the potential leakage of CO2 and to improve reservoir description as well to monitor development of geologic discontinuity (i.e., fault, crack, joint, etc.). Geophysical monitoring can be based on wireline logging or surface surveys for well-scale monitoring (high resolution and nallow area of investigation) or basin-scale monitoring (low resolution and wide area of investigation). In the meantime, crosswell tomography can make reservoir-scale monitoring to bridge the resolution gap between well logs and surface measurements. This study focuses on reservoir-scale monitoring based on crosswell seismic tomography aiming describe details of reservoir structure and monitoring migration of reservoir fluid (water and CO2). For the monitoring, we first make a sensitivity analysis on crosswell seismic tomography data with respect to CO2 saturation. For the sensitivity analysis, Rock Physics Models (RPMs) are constructed by calculating the values of density and P and S-wave velocities of a virtual CO2 injection reservoir. Since the seismic velocity of the reservoir accordingly changes as CO2 saturation changes when the CO2 saturation is less than about 20%, while when the CO2 saturation is larger than 20%, the seismic velocity is insensitive to the change, sensitivity analysis is mainly made when CO2 saturation is less than 20%. For precise simulation of seismic tomography responses for constructed RPMs, we developed a time-domain 2D elastic modeling based on finite difference method with a staggered grid employing a boundary condition of a convolutional perfectly matched layer. We further make comparison between sensitivities of seismic tomography and surface measurements for RPMs to analysis resolution

Integrated Reflection Seismic Monitoring and Reservoir Modeling for Geologic CO2 Sequestration

Energy Technology Data Exchange (ETDEWEB)

John Rogers

2011-12-31

The US DOE/NETL CCS MVA program funded a project with Fusion Petroleum Technologies Inc. (now SIGMA) to model the proof of concept of using sparse seismic data in the monitoring of CO{sub 2} injected into saline aquifers. The goal of the project was to develop and demonstrate an active source reflection seismic imaging strategy based on deployment of spatially sparse surface seismic arrays. The primary objective was to test the feasibility of sparse seismic array systems to monitor the CO{sub 2} plume migration injected into deep saline aquifers. The USDOE/RMOTC Teapot Dome (Wyoming) 3D seismic and reservoir data targeting the Crow Mountain formation was used as a realistic proxy to evaluate the feasibility of the proposed methodology. Though the RMOTC field has been well studied, the Crow Mountain as a saline aquifer has not been studied previously as a CO{sub 2} sequestration (storage) candidate reservoir. A full reprocessing of the seismic data from field tapes that included prestack time migration (PSTM) followed by prestack depth migration (PSDM) was performed. A baseline reservoir model was generated from the new imaging results that characterized the faults and horizon surfaces of the Crow Mountain reservoir. The 3D interpretation was integrated with the petrophysical data from available wells and incorporated into a geocellular model. The reservoir structure used in the geocellular model was developed using advanced inversion technologies including Fusion's ThinMAN{trademark} broadband spectral inversion. Seal failure risk was assessed using Fusion's proprietary GEOPRESS{trademark} pore pressure and fracture pressure prediction technology. CO{sub 2} injection was simulated into the Crow Mountain with a commercial reservoir simulator. Approximately 1.2MM tons of CO{sub 2} was simulated to be injected into the Crow Mountain reservoir over 30 years and subsequently let 'soak' in the reservoir for 970 years. The relatively small plume

Co-seismic deformation and gravity changes of the 2011 India-Nepal and Myanmar earthquakes

Directory of Open Access Journals (Sweden)

Liu Chengli

2012-02-01

Full Text Available Co-seismic deformation and gravity field changes caused by the 2011 Mw6. 8 Myanmar and Mw6. 9 India-Nepal earthquakes are calculated with a finite-element model and an average-slip model, respectively, based on the multi-layered elastic half-space dislocation theory. The calculated maximum horizontal displacement of the Myanmar earthquake is 36 cm, which is larger than the value of 9. 5 cm for the India-Nepal earthquake. This difference is attributed to their different focal depths and our use of different models. Except certain differences in the near field, both models give similar deformation and gravity results for the Myanmar event.

Tree-ring 14C links seismic swarm to CO2 spike at Yellowstone, USA

Science.gov (United States)

Evans, William C.; Bergfeld, D.; McGeehin, J.P.; King, J.C.; Heasler, H.

2010-01-01

Mechanisms to explain swarms of shallow seismicity and inflation-deflation cycles at Yellowstone caldera (western United States) commonly invoke episodic escape of magma-derived brines or gases from the ductile zone, but no correlative changes in the surface efflux of magmatic constituents have ever been documented. Our analysis of individual growth rings in a tree core from the Mud Volcano thermal area within the caldera links a sharp ~25% drop in 14C to a local seismic swarm in 1978. The implied fivefold increase in CO2 emissions clearly associates swarm seismicity with upflow of magma-derived fluid and shows that pulses of magmatic CO2 can rapidly traverse the 5-kmthick brittle zone, even through Yellowstone's enormous hydrothermal reservoir. The 1978 event predates annual deformation surveys, but recognized connections between subsequent seismic swarms and changes in deformation suggest that CO2 might drive both processes. ?? 2010 Geological Society of America.

Synthetic seismic monitoring using reverse-time migration and Kirchhoff migration for CO2 sequestration in Korea

Science.gov (United States)

Kim, W.; Kim, Y.; Min, D.; Oh, J.; Huh, C.; Kang, S.

2012-12-01

During last two decades, CO2 sequestration in the subsurface has been extensively studied and progressed as a direct tool to reduce CO2 emission. Commercial projects such as Sleipner, In Salah and Weyburn that inject more than one million tons of CO2 per year are operated actively as well as test projects such as Ketzin to study the behavior of CO2 and the monitoring techniques. Korea also began the CCS (CO2 capture and storage) project. One of the prospects for CO2 sequestration in Korea is the southwestern continental margin of Ulleung basin. To monitor the behavior of CO2 underground for the evaluation of stability and safety, several geophysical monitoring techniques should be applied. Among various geophysical monitoring techniques, seismic survey is considered as the most effective tool. To verify CO2 migration in the subsurface more effectively, seismic numerical simulation is an essential process. Furthermore, the efficiency of the seismic migration techniques should be investigated for various cases because numerical seismic simulation and migration test help us accurately interpret CO2 migration. In this study, we apply the reverse-time migration and Kirchhoff migration to synthetic seismic monitoring data generated for the simplified model based on the geological structures of Ulleung basin in Korea. Synthetic seismic monitoring data are generated for various cases of CO2 migration in the subsurface. From the seismic migration images, we can investigate CO2 diffusion patterns indirectly. From seismic monitoring simulation, it is noted that while the reverse-time migration generates clear subsurface images when subsurface structures are steeply dipping, Kirchhoff migration has an advantage in imaging horizontal-layered structures such as depositional sediments appearing in the continental shelf. The reverse-time migration and Kirchhoff migration present reliable subsurface images for the potential site characterized by stratigraphical traps. In case of

Detection of cracks with low vertical offset in clayey formations from galleries by using seismic methods. Tournemire experimental station. First part: problem analysis and measurement sizing

International Nuclear Information System (INIS)

Bretaudeau, Francois; Gelis, Celine; Cabrera, Justo; Leparoux, Donatienne; Cote, Philippe

2012-01-01

Within the frame of the expertise of the ANDRA file on the project of storage of radioactive wastes in clayey formations, the detection of natural cracks which could locally alter the argillite containment properties is a crucial issue. As some previous studies showed that some cracks exhibiting a low vertical offset could not be detected in clayey formations from the surface, this document reports a study which aimed at assessing the possibility of detection of such a crack by means of seismic methods directly implemented from underground works. It reports a detailed analysis of the seismic imagery problem, the characterization of different areas of the investigated environment, the assessment and validation of various hypotheses by using experimental data obtained in an experimental station and numerical simulations. The potential of each envisaged method (migration, tomography, wave form inversion) is assessed, notably with respect to synthetic seismic data obtained by numerical modelling. Preliminary results are used to size a complete seismic measurement campaign aimed at the characterization of the crack area, and at the assessment of detection limitations of the different methods

Training toward Advanced 3D Seismic Methods for CO2 Monitoring, Verification, and Accounting

Energy Technology Data Exchange (ETDEWEB)

Christopher Liner

2012-05-31

The objective of our work is graduate and undergraduate student training related to improved 3D seismic technology that addresses key challenges related to monitoring movement and containment of CO{sub 2}, specifically better quantification and sensitivity for mapping of caprock integrity, fractures, and other potential leakage pathways. We utilize data and results developed through previous DOE-funded CO{sub 2} characterization project (DE-FG26-06NT42734) at the Dickman Field of Ness County, KS. Dickman is a type locality for the geology that will be encountered for CO{sub 2} sequestration projects from northern Oklahoma across the U.S. midcontinent to Indiana and Illinois. Since its discovery in 1962, the Dickman Field has produced about 1.7 million barrels of oil from porous Mississippian carbonates with a small structural closure at about 4400 ft drilling depth. Project data includes 3.3 square miles of 3D seismic data, 142 wells, with log, some core, and oil/water production data available. Only two wells penetrate the deep saline aquifer. In a previous DOE-funded project, geological and seismic data were integrated to create a geological property model and a flow simulation grid. We believe that sequestration of CO{sub 2} will largely occur in areas of relatively flat geology and simple near surface, similar to Dickman. The challenge is not complex geology, but development of improved, lower-cost methods for detecting natural fractures and subtle faults. Our project used numerical simulation to test methods of gathering multicomponent, full azimuth data ideal for this purpose. Our specific objectives were to apply advanced seismic methods to aide in quantifying reservoir properties and lateral continuity of CO{sub 2} sequestration targets. The purpose of the current project is graduate and undergraduate student training related to improved 3D seismic technology that addresses key challenges related to monitoring movement and containment of CO{sub 2

Vp-Vs relationship and amplitude variation with offset modelling of glauconitic greensand

DEFF Research Database (Denmark)

Hossain, Zakir; Mukerji, Tapan; Fabricius, Ida Lykke

2012-01-01

The relationship between Vp and Vs may be used to predict Vs where only Vp is known. Vp/Vs is also used to identify pore fluids from seismic data and amplitude variation with offset analysis. Theoretical, physical, as well as statistical empirical Vp-Vs relationships have been proposed...... modelling works well for greensand shear-wave velocity prediction. We model the seismic response of glauconitic greensand by using laboratory data from the Nini field. Our studies here reveal that brine-saturated glauconitic greensand can have a similar seismic response to that from oil-saturated quartzitic...

The MCE (Maximum Credible Earthquake) - an approach to reduction of seismic risk

International Nuclear Information System (INIS)

Asmis, G.J.K.; Atchison, R.J.

1979-01-01

It is the responsibility of the Regulatory Body (in Canada, the AECB) to ensure that radiological risks resulting from the effects of earthquakes on nuclear facilities, do not exceed acceptable levels. In simplified numerical terms this means that the frequency of an unacceptable radiation dose must be kept below 10 -6 per annum. Unfortunately, seismic events fall into the class of external events which are not well defined at these low frequency levels. Thus, design earthquakes have been chosen, at the 10 -3 - 10 -4 frequency level, a level commensurate with the limits of statistical data. There exists, therefore, a need to define an additional level of earthquake. A seismic design explicitly and implicitly recognizes three levels of earthquake loading; one comfortably below yield, one at or about yield, and one at ultimate. The ultimate level earthquake, contrary to the first two, has been implicitly addressed by conscientious designers by choosing systems, materials and details compatible with postulated dynamic forces. It is the purpose of this paper to discuss the regulatory specifications required to quantify this third level, or Maximum Credible Earthquake (MCE). (orig.)

Velocity Model for CO2 Sequestration in the Southeastern United States Atlantic Continental Margin

Science.gov (United States)

Ollmann, J.; Knapp, C. C.; Almutairi, K.; Almayahi, D.; Knapp, J. H.

2017-12-01

The sequestration of carbon dioxide (CO2) is emerging as a major player in offsetting anthropogenic greenhouse gas emissions. With 40% of the United States' anthropogenic CO2 emissions originating in the southeast, characterizing potential CO2 sequestration sites is vital to reducing the United States' emissions. The goal of this research project, funded by the Department of Energy (DOE), is to estimate the CO2 storage potential for the Southeastern United States Atlantic Continental Margin. Previous studies find storage potential in the Atlantic continental margin. Up to 16 Gt and 175 Gt of storage potential are estimated for the Upper Cretaceous and Lower Cretaceous formations, respectively. Considering 2.12 Mt of CO2 are emitted per year by the United States, substantial storage potential is present in the Southeastern United States Atlantic Continental Margin. In order to produce a time-depth relationship, a velocity model must be constructed. This velocity model is created using previously collected seismic reflection, refraction, and well data in the study area. Seismic reflection horizons were extrapolated using well log data from the COST GE-1 well. An interpolated seismic section was created using these seismic horizons. A velocity model will be made using P-wave velocities from seismic reflection data. Once the time-depth conversion is complete, the depths of stratigraphic units in the seismic refraction data will be compared to the newly assigned depths of the seismic horizons. With a lack of well control in the study area, the addition of stratigraphic unit depths from 171 seismic refraction recording stations provides adequate data to tie to the depths of picked seismic horizons. Using this velocity model, the seismic reflection data can be presented in depth in order to estimate the thickness and storage potential of CO2 reservoirs in the Southeastern United States Atlantic Continental Margin.

"3D_Fault_Offsets," a Matlab Code to Automatically Measure Lateral and Vertical Fault Offsets in Topographic Data: Application to San Andreas, Owens Valley, and Hope Faults

Science.gov (United States)

Stewart, N.; Gaudemer, Y.; Manighetti, I.; Serreau, L.; Vincendeau, A.; Dominguez, S.; Mattéo, L.; Malavieille, J.

2018-01-01

Measuring fault offsets preserved at the ground surface is of primary importance to recover earthquake and long-term slip distributions and understand fault mechanics. The recent explosion of high-resolution topographic data, such as Lidar and photogrammetric digital elevation models, offers an unprecedented opportunity to measure dense collections of fault offsets. We have developed a new Matlab code, 3D_Fault_Offsets, to automate these measurements. In topographic data, 3D_Fault_Offsets mathematically identifies and represents nine of the most prominent geometric characteristics of common sublinear markers along faults (especially strike slip) in 3-D, such as the streambed (minimum elevation), top, free face and base of channel banks or scarps (minimum Laplacian, maximum gradient, and maximum Laplacian), and ridges (maximum elevation). By calculating best fit lines through the nine point clouds on either side of the fault, the code computes the lateral and vertical offsets between the piercing points of these lines onto the fault plane, providing nine lateral and nine vertical offset measures per marker. Through a Monte Carlo approach, the code calculates the total uncertainty on each offset. It then provides tools to statistically analyze the dense collection of measures and to reconstruct the prefaulted marker geometry in the horizontal and vertical planes. We applied 3D_Fault_Offsets to remeasure previously published offsets across 88 markers on the San Andreas, Owens Valley, and Hope faults. We obtained 5,454 lateral and vertical offset measures. These automatic measures compare well to prior ones, field and remote, while their rich record provides new insights on the preservation of fault displacements in the morphology.

Two types of SDR recognised in pre-stack velocity analysis of ultra-long-offset seismic reflection data in the South Atlantic

Science.gov (United States)

Collier, J.; McDermott, C.; Lonergan, L.; McDermott, K.; Bellingham, P.

2017-12-01

Our understanding of continental breakup at volcanic margins has lagged behind that of non-volcanic margins in recent years. This is largely due to seismic imaging problems caused by the presence of thick packages of Seaward-Dipping Reflectors (SDRs) in the continent-ocean transition zone. These packages consist of interbedded tholeiitic lava flows, volcanic tuffs and terrestrial sediment that results in scattering, peg-leg multiples and defocusing of seismic energy. Here we analyse three ultra-long-offset (10.2 km), wide-bandwidth (5-100 Hz) seismic reflection profiles acquired by ION-GXT offshore South America during 2009-12 to gain new insights into the velocity structure of the SDRs and hence pattern of magmatism during continental breakup. We observe two seismic velocity patterns within the SDRs. The most landward packages show high velocity anomaly "bulls-eyes" of up to 1 km s-1. These highs occur where the stacked section shows them to thicken at the down-dip end of individual packages that are bounded by faults. All lines show 5-6 velocity highs spaced approximately 10 km apart. We interpret the velocity bulls-eyes as depleted mafic or ultramafic bodies that fed the sub-aerial tholeiitic lava flows during continental stretching. Similar relationships have been observed in outcrop onshore but have not been previously demonstrated in seismic data. The bulls-eye packages pass laterally into SDR packages that show no velocity highs. These packages are not associated with faulting and become more extensive going north towards the impact point of the Tristan da Cunha hotspot. This second type of SDR coincides with linear magnetic anomalies. We interpret these SDRs as the products of sub-aerial oceanic spreading similar to those seen on Iceland and described in the classic "Hinz model" and marine geophysical literature. Our work demonstrates that these SDRs are preceded by ones generated during an earlier phase of mechanical thinning of the continental crust. The

Seismic monitoring at the Decatur, Ill., CO2 sequestration demonstration site

Science.gov (United States)

Kaven, Joern; Hickman, Stephen H.; McGarr, Arthur F.; Walter, Steve R.; Ellsworth, William L.

2014-01-01

The viability of carbon capture and storage (CCS) to reduce emissions of greenhouse gases depends on the ability to safely sequester large quantities of CO2 over geologic time scales. One concern with CCS is the potential of induced seismicity. We report on ongoing seismic monitoring by the U.S. Geological Survey (USGS) at a CCS demonstration site in Decatur, IL, in an effort to understand the potential hazards posed by injection-induced seismicity associated with geologic CO2 sequestration. At Decatur, super-critical CO2 is injected at 2.1 km depth into the 550-m-thick Mt. Simon Sandstone, which directly overlies granitic basement. The primary sealing cap rock is the Eau Claire Shale, a 100- to 150-m-thick unit at a depth of roughly 1.5 km. The USGS seismic network consists of 12 stations, three of which have surface accelerometers and three-component borehole geophones. We derived a one-dimensional velocity models from a vertical seismic profile acquired by Archer-Daniels-Midland (ADM) and the Illinois State Geological Survey (ISGS) to a depth of 2.2 km, tied into shallow acoustic logs from our borehole stations and assuming a 6 km/sec P-wave velocity for granite below 2.2 km. We further assume a constant ratio of P- to S-wave velocities of 1.83, as derived from velocity model inversions. We use this velocity model to locate seismic events, all of which are within the footprint of our network. So far magnitudes of locatable events range from Mw = -1.52 to 1.07. We further improved the hypocentral precision of microseismic events when travel times and waveforms are sufficiently similar by employing double-difference relocation techniques, with relative location errors less than 80 m horizontally and 100 m vertically. We observe tend to group in three distinct clusters: ∼0.4 to 1.0 km NE, 1.6 to 2.4 km N, and ∼1.8 to 2.6 km WNW from the injection well. The first cluster of microseismicity forms a roughly linear trend, which may represent a pre-existing geologic

Geophysical Monitoring at the CO2SINK Site: Combining Seismic and Geoelectric Data

Science.gov (United States)

Giese, R.; Lüth, S.; Cosma, C.; Juhlin, C.; Kiessling, D.; Schütt, H.; Schöbel, B.; Schmidt-Hattenberger, C.; Schilling, F.; Co2SINK Group

2009-04-01

The CO2SINK project at the German town of Ketzin (near Berlin), is aimed at a pilot storage of CO2, and at developing and testing efficient integrated monitoring procedures (physical, chemical, and biological observations) for assessing the processes triggered within the reservoir by a long term injection operation. In particular, geophysical methods as seismic and geoelectric measurements have delivered the structural framework, and they enable to observe the reaction of the reservoir and the caprock to CO2 propagation at locations which are not accessible for direct observations. We report on the seismic monitoring program of the CO2SINK project which comprises baseline and repeat observations at different scales in time and space, combined with comprehensive geoelectrical monitoring performed in the Ketzin wells and on the surface. The main objectives of the 3D seismic survey (carried out in spring 2005) were to provide the structural model around the location of the Ketzin wells, to verify earlier geologic interpretations of structure based on vintage 2D seismic and borehole data, as well as providing a baseline for future seismic surveys. The uppermost 1000 m are well imaged and show an anticlinal structure with an east-west striking central graben on its top. The 3D baseline survey was extended by VSP (vertical seismic profiling), MSP (moving source profiling) on 7 profiles, and crosshole tomographic measurements. 2D "star" measurements were carried out on the 7 MSP profiles in order to tie-in the down-hole surveys with the 3D baseline survey. These measurements provide enhanced resolution in time (faster and more cost effective than a full 3D survey) and space (higher source and receiver frequencies). Three crosshole measurements were performed, one baseline survey in May 2008, and two repeats in July and August 2008, respectively. A third crosshole repeat is planned for a later stage in the project when a steady state situation has been reached in the

Application of Time-Lapse Seismic Monitoring for the Control and Optimization of CO2 Enhanced Oil Recovery Operations

Energy Technology Data Exchange (ETDEWEB)

Brian Toelle

2008-11-30

This project, 'Application of Time-Lapse Seismic Monitoring for the Control and Optimization of CO{sub 2} Enhanced Oil Recovery Operations', investigated the potential for monitoring CO{sub 2} floods in carbonate reservoirs through the use of standard p-wave seismic data. This primarily involved the use of 4D seismic (time lapse seismic) in an attempt to observe and map the movement of the injected CO{sub 2} through a carbonate reservoir. The differences between certain seismic attributes, such as amplitude, were used for this purpose. This technique has recently been shown to be effective in CO{sub 2} monitoring in Enhanced Oil Recovery (EOR) projects, such as Weyborne. This study was conducted in the Charlton 30/31 field in the northern Michigan Basin, which is a Silurian pinnacle reef that completed its primary production in 1997 and was scheduled for enhanced oil recovery using injected CO{sub 2}. Prior to injection an initial 'Base' 3D survey was obtained over the field and was then processed and interpreted. CO{sub 2} injection within the main portion of the reef was conducted intermittently during 13 months starting in August 2005. During this time, 29,000 tons of CO{sub 2} was injected into the Guelph formation, historically known as the Niagaran Brown formation. By September 2006, the reservoir pressure within the reef had risen to approximately 2000 lbs and oil and water production from the one producing well within the field had increased significantly. The determination of the reservoir's porosity distribution, a critical aspect of reservoir characterization and simulation, proved to be a significant portion of this project. In order to relate the differences observed between the seismic attributes seen on the multiple 3D seismic surveys and the actual location of the CO{sub 2}, a predictive reservoir simulation model was developed based on seismic attributes obtained from the base 3D seismic survey and available well data. This

Carbon offset potentials and design: Anticipating future public policy

International Nuclear Information System (INIS)

Trexler, M.C.; Kosloff, L.H.; Gowen, M.

1994-01-01

Carbon offsets offer CO 2 emitters the opportunity to compensate for some proportion of their CO 2 emissions through the pursuit of emissions reduction or carbon sequestration projects beyond their own operational boundaries. The flexibility to pursue carbon offsets ''off-site'' can dramatically reduce the costs of achieving a given net emissions reduction. The future role of carbon offsets, however, continues to be a topic of considerable debate. Several processes are currently under way nationally and internationally that will help shape this role. This paper discusses how alternative policy outcomes could encourage or restrict the viability of carbon offsets as a component of corporate climate change mitigation portfolios and proposes criteria by which projects should be evaluated prior to the finalization of national or international policy frameworks. Based on these outcomes, the potential for offsets could be very large or very modest. It is vital that policy development in the offset arena account for the still voluntary nature of mitigation efforts and that the objective of climate change mitigation not be forgotten in the push for offset rules and regulations. At the same time, carbon offsets are far from a panacea for climate change mitigation and should be evaluated in the context of a larger global mitigation portfolio

Time-lapse seismic waveform modelling and attribute analysis using hydromechanical models for a deep reservoir undergoing depletion

Science.gov (United States)

He, Y.-X.; Angus, D. A.; Blanchard, T. D.; Wang, G.-L.; Yuan, S.-Y.; Garcia, A.

2016-04-01

Extraction of fluids from subsurface reservoirs induces changes in pore pressure, leading not only to geomechanical changes, but also perturbations in seismic velocities and hence observable seismic attributes. Time-lapse seismic analysis can be used to estimate changes in subsurface hydromechanical properties and thus act as a monitoring tool for geological reservoirs. The ability to observe and quantify changes in fluid, stress and strain using seismic techniques has important implications for monitoring risk not only for petroleum applications but also for geological storage of CO2 and nuclear waste scenarios. In this paper, we integrate hydromechanical simulation results with rock physics models and full-waveform seismic modelling to assess time-lapse seismic attribute resolution for dynamic reservoir characterization and hydromechanical model calibration. The time-lapse seismic simulations use a dynamic elastic reservoir model based on a North Sea deep reservoir undergoing large pressure changes. The time-lapse seismic traveltime shifts and time strains calculated from the modelled and processed synthetic data sets (i.e. pre-stack and post-stack data) are in a reasonable agreement with the true earth models, indicating the feasibility of using 1-D strain rock physics transform and time-lapse seismic processing methodology. Estimated vertical traveltime shifts for the overburden and the majority of the reservoir are within ±1 ms of the true earth model values, indicating that the time-lapse technique is sufficiently accurate for predicting overburden velocity changes and hence geomechanical effects. Characterization of deeper structure below the overburden becomes less accurate, where more advanced time-lapse seismic processing and migration is needed to handle the complex geometry and strong lateral induced velocity changes. Nevertheless, both migrated full-offset pre-stack and near-offset post-stack data image the general features of both the overburden and

Detection of a westward hotspot offset in the atmosphere of hot gas giant CoRoT-2b

Science.gov (United States)

Dang, Lisa; Cowan, Nicolas B.; Schwartz, Joel C.; Rauscher, Emily; Zhang, Michael; Knutson, Heather A.; Line, Michael; Dobbs-Dixon, Ian; Deming, Drake; Sundararajan, Sudarsan; Fortney, Jonathan J.; Zhao, Ming

2018-03-01

Short-period planets exhibit day-night temperature contrasts of hundreds to thousands of kelvin. They also exhibit eastward hotspot offsets whereby the hottest region on the planet is east of the substellar point1; this has been widely interpreted as advection of heat due to eastward winds2. We present thermal phase observations of the hot Jupiter CoRoT-2b obtained with the Infrared Array Camera (IRAC) on the Spitzer Space Telescope. These measurements show the most robust detection to date of a westward hotspot offset of 23 ± 4°, in contrast with the nine other planets with equivalent measurements3-10. The peculiar infrared flux map of CoRoT-2b may result from westward winds due to non-synchronous rotation11 or magnetic effects12,13, or partial cloud coverage, that obscure the emergent flux from the planet's eastern hemisphere14-17. Non-synchronous rotation and magnetic effects may also explain the planet's anomalously large radius12,18. On the other hand, partial cloud coverage could explain the featureless dayside emission spectrum of the planet19,20. If CoRoT-2b is not tidally locked, then it means that our understanding of star-planet tidal interaction is incomplete. If the westward offset is due to magnetic effects, our result represents an opportunity to study an exoplanet's magnetic field. If it has eastern clouds, then it means that a greater understanding of large-scale circulation on tidally locked planets is required.

Anomalous changes of diffuse CO_{2} emission and seismic activity at Teide volcano, Tenerife, Canary Islands

Science.gov (United States)

García-Hernández, Rubén; Melián, Gladys; D'Auria, Luca; Asensio-Ramos, María; Alonso, Mar; Padilla, Germán D.; Rodríguez, Fátima; Padrón, Eleazar; Barrancos, José; García-Merino, Marta; Amonte, Cecilia; Pérez, Aarón; Calvo, David; Hernández, Pedro A.; Pérez, Nemesio M.

2017-04-01

Tenerife (2034 km2) is the largest of the Canary Islands and hosts four main active volcanic edifices: three volcanic rifts and a central volcanic complex, Las Cañadas, which is characterized by the eruption of differentiated magmas. Laying inside Las Cañadas a twin stratovolcanoes system, Pico Viejo and Teide, has been developed. Although there are no visible gas emanations along the volcanic rifts of Tenerife, the existence of a volcanic-hydrothermal system beneath Teide volcano is suggested by the occurrence of a weak fumarolic system, steamy ground and high rates of diffuse CO2 degassing all around the summit cone of Teide. Soil CO2 efflux surveys have been performed at the summit crater of Teide volcano since 1999, to determine the diffuse CO2 emission from the summit crater and to evaluate the temporal variations of CO2 efflux and their relationships with seismic-volcanic activity. Soil CO2 efflux and soil temperature have been always measured at the same 38 observation sites homogeneously distributed within an area of about 6,972 m2 inside the summit crater. Soil CO2 diffuse effluxes were estimated according to the accumulation chamber method by means of a non-dispersive infrared (NDIR) LICOR-820 CO2 analyzer. Historical seismic activity in Tenerife has been characterized by low- to moderate-magnitude events (M de Canarias (INVOLCAN) registered an earthquake of M 2.5 located in the vertical of Teide volcano with a depth of 6.6 km. It was the strongest earthquake located inside Cañadas caldera since 2004. Between October 11 and December 13, 2016, a continuous increase on the diffuse CO2 emission was registered, from 21.3 ± 2.0 to 101.7 ± 20.7 t d-1, suggesting the occurrence of future increase in the seismic-volcanic activity. In fact, this precursory signal preceded the occurrence of the 2.5 seismic event and no significant horizontal and vertical displacements were registered by the Canary GPS network belonged to INVOLCAN. This seismic event was

Delineation of seismic source zones based on seismicity parameters ...

Indian Academy of Sciences (India)

In the present study, an attempt has been made to delineate seismic source zones in the study area (south India) based on the seismicity parameters. Seismicity parameters and the maximum probable earthquake for these source zones were evaluated and were used in the hazard evaluation. The probabilistic evaluation of ...

4-D High-Resolution Seismic Reflection Monitoring of Miscible CO2 Injected into a Carbonate Reservoir

Energy Technology Data Exchange (ETDEWEB)

Richard D. Miller; Abdelmoneam E. Raef; Alan P. Byrnes; William E. Harrison

2007-06-30

The objective of this research project was to acquire, process, and interpret multiple high-resolution 3-D compressional wave and 2-D, 2-C shear wave seismic data in the hopes of observing changes in fluid characteristics in an oil field before, during, and after the miscible carbon dioxide (CO{sub 2}) flood that began around December 1, 2003, as part of the DOE-sponsored Class Revisit Project (DOE No.DE-AC26-00BC15124). Unique and key to this imaging activity is the high-resolution nature of the seismic data, minimal deployment design, and the temporal sampling throughout the flood. The 900-m-deep test reservoir is located in central Kansas oomoldic limestones of the Lansing-Kansas City Group, deposited on a shallow marine shelf in Pennsylvanian time. After 30 months of seismic monitoring, one baseline and eight monitor surveys clearly detected changes that appear consistent with movement of CO{sub 2} as modeled with fluid simulators and observed in production data. Attribute analysis was a very useful tool in enhancing changes in seismic character present, but difficult to interpret on time amplitude slices. Lessons learned from and tools/techniques developed during this project will allow high-resolution seismic imaging to be routinely applied to many CO{sub 2} injection programs in a large percentage of shallow carbonate oil fields in the midcontinent.

VSP Monitoring of CO2 Injection at the Aneth Oil Field in Utah

Science.gov (United States)

Huang, L.; Rutledge, J.; Zhou, R.; Denli, H.; Cheng, A.; Zhao, M.; Peron, J.

2008-12-01

Remotely tracking the movement of injected CO2 within a geological formation is critically important for ensuring safe and long-term geologic carbon sequestration. To study the capability of vertical seismic profiling (VSP) for remote monitoring of CO2 injection, a geophone string with 60 levels and 96 channels was cemented into a monitoring well at the Aneth oil field in Utah operated by Resolute Natural Resources and Navajo National Oil and Gas Company. The oil field is located in the Paradox Basin of southeastern Utah, and was selected by the Southwest Regional Partnership on Carbon Sequestration, supported by the U.S. Department of Energy, to demonstrate combined enhanced oil recovery (EOR) and CO2 sequestration. The geophones are placed at depths from 805 m to 1704 m, and the oil reservoir is located approximately from 1731 m to 1786 m in depth. A baseline VSP dataset with one zero-offset and seven offset source locations was acquired in October, 2007 before CO2 injection. The offsets/source locations are approximately 1 km away from the monitoring well with buried geophone string. A time-lapse VSP dataset with the same source locations was collected in July, 2008 after five months of CO2/water injection into a horizontal well adjacent to the monitoring well. The total amount of CO2 injected during the time interval between the two VSP surveys was 181,000 MCF (million cubic feet), or 10,500 tons. The time-lapse VSP data are pre-processed to balance the phase and amplitude of seismic events above the oil reservoir. We conduct wave-equation migration imaging and interferometry analysis using the pre-processed time-lapse VSP data. The results demonstrate that time-lapse VSP surveys with high-resolution migration imaging and scattering analysis can provide reliable information about CO2 migration. Both the repeatability of VSP surveys and sophisticated time-lapse data pre-processing are essential to make VSP as an effective tool for monitoring CO2 injection.

Correction of elevation offsets in multiple co-located lidar datasets

Science.gov (United States)

Thompson, David M.; Dalyander, P. Soupy; Long, Joseph W.; Plant, Nathaniel G.

2017-04-07

IntroductionTopographic elevation data collected with airborne light detection and ranging (lidar) can be used to analyze short- and long-term changes to beach and dune systems. Analysis of multiple lidar datasets at Dauphin Island, Alabama, revealed systematic, island-wide elevation differences on the order of 10s of centimeters (cm) that were not attributable to real-world change and, therefore, were likely to represent systematic sampling offsets. These offsets vary between the datasets, but appear spatially consistent within a given survey. This report describes a method that was developed to identify and correct offsets between lidar datasets collected over the same site at different times so that true elevation changes over time, associated with sediment accumulation or erosion, can be analyzed.

Vertical seismic profiling and integration with reflection seismic studies at Laxemar, 2000

International Nuclear Information System (INIS)

Juhlin, C.; Bergman, B.; Cosma, C.; Keskinen, J.; Enescu, N.

2002-02-01

Vertical seismic profile (VSP) data were acquired in October 2000 in the 1700 m deep KLX02 borehole, near Laxemar in southeastern Sweden. The objectives of the VSP were to image reflectors in the borehole for correlation with surface seismic and borehole data, study the signal penetration of explosive versus mechanical sources and determine the seismic velocity as a function of depth. Five principal source points were used, one located close to the KLX02 wellhead and 4 others that were offset by about 200 m to 400 m. An explosive source was only used at the wellhead and consisted of 15 grams of dynamite in 90 cm deep shot holes in bedrock. A swept impact seismic source (SIST) was also used at the wellhead, as well as at the other four offset source points. The primary SIST source consisted of a computer controlled mechanical hammer mounted on a tractor. By activating the hammer over a 15 second sweep length, the total energy transferred to the ground is on the same order as that produced by the dynamite. The recorded data are then processed to generate seismic records that are equivalent to a single impact source. A smaller hand held SIST source was also tested at the wellhead. Tests of both the tractor mounted source and dynamite were made at a location offset somewhat from the wellhead at a site containing loose sediments at the surface. Full waveform sonic, resistivity and gamma logs were also acquired in conjunction the VSP survey. A comparison between the explosive and large SIST source shows that comparable energy levels are produced by the two methods. The SIST source appears to be more stable in terms of the energy level, although the frequency content of data are somewhat lower. However, its most significant advantage is the low cost of preparation of the source points and the speed of the acquisition. Numerous reflections are observed on the VSP, as is the case on the surface seismic, implying a complex structure in the vicinity of the KLX02 borehole

Vertical seismic profiling and integration with reflection seismic studies at Laxemar, 2000

Energy Technology Data Exchange (ETDEWEB)

Juhlin, C.; Bergman, B. [Uppsala Univ. (Sweden); Cosma, C.; Keskinen, J.; Enescu, N. [Vibrometric Oy, Helsinki (Finland)

2002-02-01

Vertical seismic profile (VSP) data were acquired in October 2000 in the 1700 m deep KLX02 borehole, near Laxemar in southeastern Sweden. The objectives of the VSP were to image reflectors in the borehole for correlation with surface seismic and borehole data, study the signal penetration of explosive versus mechanical sources and determine the seismic velocity as a function of depth. Five principal source points were used, one located close to the KLX02 wellhead and 4 others that were offset by about 200 m to 400 m. An explosive source was only used at the wellhead and consisted of 15 grams of dynamite in 90 cm deep shot holes in bedrock. A swept impact seismic source (SIST) was also used at the wellhead, as well as at the other four offset source points. The primary SIST source consisted of a computer controlled mechanical hammer mounted on a tractor. By activating the hammer over a 15 second sweep length, the total energy transferred to the ground is on the same order as that produced by the dynamite. The recorded data are then processed to generate seismic records that are equivalent to a single impact source. A smaller hand held SIST source was also tested at the wellhead. Tests of both the tractor mounted source and dynamite were made at a location offset somewhat from the wellhead at a site containing loose sediments at the surface. Full waveform sonic, resistivity and gamma logs were also acquired in conjunction the VSP survey. A comparison between the explosive and large SIST source shows that comparable energy levels are produced by the two methods. The SIST source appears to be more stable in terms of the energy level, although the frequency content of data are somewhat lower. However, its most significant advantage is the low cost of preparation of the source points and the speed of the acquisition. Numerous reflections are observed on the VSP, as is the case on the surface seismic, implying a complex structure in the vicinity of the KLX02 borehole

Simulation on Vehicle Vibration Offset of NX70 Flatcar

Directory of Open Access Journals (Sweden)

Han Yanhui

2014-11-01

Full Text Available The current rolling stock gauge for standard gauge railway is a static gauge to check the vehicle frame. The contradiction of large construction gauge and small rolling stock gauge has always existed. It is important to set down the clearance requirements in respect of physical size for the safe passage of rail vehicles. Reasonably determining the maximum vibration offset can improve the efficiency of clearance. As an example, analyze the complex vibration of NX70 flat car by simulation test on the running track. Comprehensive considering the track model, loading plan, line conditions and running speed, then SIMPACK is used to present the vehicle system dynamics simulation model. After researching simulation result, respectively determine the maximum vehicle vibration offset for railroads of Class I, Class II and Class III on the height of the center of gravity 2000 mm and 2400 mm. According to the clearance between the structure gauge and the position of maximum vibration offset, analyze the safety of vehicle operation since the center of gravity is higher than before.

Characteristics and structure of turbulent 3D offset jets

International Nuclear Information System (INIS)

Agelin-Chaab, M.; Tachie, M.F.

2011-01-01

Highlights: → We investigated three-dimensional turbulent offset jets using particle image velocimetry. → We examined the effects of offset height and Reynolds number on the structure of 3D offset jets. → Effects of Reynolds number and offset height on the decay and growth rates exist close to the exit. → This study provides additional insight and comprehensive data for validating numerical models. - Abstract: Three-dimensional turbulent offset jets were investigated using a particle image velocimetry technique. The measurements were performed at three different exit Reynolds numbers and for four offset heights. The results in the early region of flow development clearly show significant effects of Reynolds number and offset height on the decay of maximum mean velocity and growth of the shear layer. On the contrary, the decay and spread rates were found to be nearly independent of offset height at larger downstream distances. The decay rates of 1.18 ± 0.03 as well as the spread rates of 0.055 ± 0.001 and 0.250 ± 0.005 obtained, respectively, in the wall-normal and lateral directions fall in the range of values reported in previous studies. The locations of the maximum mean velocities increased nearly linearly with streamwise distance in the self-similar region. Analysis from two-point velocity correlations revealed substantially larger structures in the outer layer and self-similar region than in the inner layer and developing region. It was also observed that the hairpin vortices in the inner regions of the wall jets are inclined at angles of 11.2 o ± 0.6 o , which are in good agreement with reported values in boundary layer studies.

Seismic reflection data imaging and interpretation from Braniewo2014 experiment using additional wide-angle refraction and reflection and well-logs data

Science.gov (United States)

Trzeciak, Maciej; Majdański, Mariusz; Białas, Sebastian; Gaczyński, Edward; Maksym, Andrzej

2015-04-01

Braniewo2014 reflection and refraction experiment was realized in cooperation between Polish Oil and Gas Company (PGNiG) and the Institute of Geophysics (IGF), Polish Academy of Sciences, near the locality of Braniewo in northern Poland. PGNiG realized a 20-km-long reflection profile, using vibroseis and dynamite shooting; the aim of the reflection survey was to characterise Silurian shale gas reservoir. IGF deployed 59 seismic stations along this profile and registered additional full-spread wide-angle refraction and reflection data, with offsets up to 12 km; maximum offsets from the seismic reflection survey was 3 km. To improve the velocity information two velocity logs from near deep boreholes were used. The main goal of the joint reflection-refraction interpretation was to find relations between velocity field from reflection velocity analysis and refraction tomography, and to build a velocity model which would be consistent for both, reflection and refraction, datasets. In this paper we present imaging results and velocity models from Braniewo2014 experiment and the methodology we used.

Band offsets of novel CoTiO{sub 3}/Ag{sub 3}VO{sub 4} heterojunction measured by X-ray photoelectron spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Wangkawong, Kanlayawat [Department of Chemistry, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Tantraviwat, Doldet [Thai Microelectronics Center (TMEC), National Electronics and Computer Technology Center (NECTEC), Chachoengsao 24000 (Thailand); Phanichphant, Sukon [Materials Science Research Centre, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Inceesungvorn, Burapat, E-mail: binceesungvorn@gmail.com [Department of Chemistry, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand)

2015-01-01

Highlights: • Band lineup of novel CoTiO{sub 3}/Ag{sub 3}VO{sub 4} composite is determined by semidirect XPS method. • The composite forms a type-II staggered heterojunction. • Valence and conduction-band offsets are 0.2 ± 0.3 and −0.6 ± 0.3 eV, respectively. • Band lineup determination is needed for understanding charge transfer at interfaces. - Abstract: The energy band diagram and band offsets of the novel CoTiO{sub 3}/Ag{sub 3}VO{sub 4} heterojunction photocatalyst are investigated by X-ray photoelectron spectroscopy for the first time. Excluding the strain effect, the valence-band and conduction-band offsets are determined to be 0.2 ± 0.3 eV and −0.6 ± 0.3 eV, respectively. The CoTiO{sub 3}/Ag{sub 3}VO{sub 4} composite forms a type-II heterojunction, for which the photogenerated charge carriers could be effectively separated. The results suggest that determination of the energy band structure is crucial for understanding the photogenerated charge transfer mechanism at the interfaces, hence the corresponding photocatalytic activity and would also be beneficial to the design of new and efficient heterostructure-based photocatalysts.

Influence of crustal layering and thickness on co-seismic effects of Wenchuan earthquake

Directory of Open Access Journals (Sweden)

Tan Hongbo

2011-02-01

Full Text Available Using the PSGRN/PSCMP software and the fault model offered by USGS and on the basis of finite rectangular dislocation theory and the local layered wave velocity structures of the crust-upper-mantle, the influences of crustal layering and thickness on co-seismic gravity changes and deformation of Wenchuan earthquake have been simulated. The results indicate that; the influences have a relationship with the attitude of faults and the relative position between calculated points and fault. The difference distribution form of simulated results between the two models is similar to that of co-seismic effect. For the per centum distribution, it’s restricted by the zero line of the co-seismic effects obviously. Its positive is far away from the zero line. For the crustal thickness, the effect is about 10% – 20%. The negative and the effect over 30% focus around the zero line. The average influences of crustal layering and thickness for the E-W displacement, N-S displacement, vertical displacement and gravity changes are 18.4%,18.0%, 15.8% and 16.2% respectively, When the crustal thickness is 40 km, they are 4.6%, 5.3%, 3.8% and 3.8%. Then the crustal thickness is 70 km, the average influences are 3.5%, 4.6%, 3.0% and 2.5% respectively.

Reflection imaging of the Moon's interior using deep-moonquake seismic interferometry

NARCIS (Netherlands)

Nishitsuji, Y.; Rowe, CA; Wapenaar, C.P.A.; Draganov, D.S.

2016-01-01

The internal structure of the Moon has been investigated over many years using a variety of seismic methods, such as travel time analysis, receiver functions, and tomography. Here we propose to apply body-wave seismic interferometry to deep moonquakes in order to retrieve zero-offset reflection

A multi-offset vertical profiling (VSP) experiment for anisotropy analysis and imaging

Energy Technology Data Exchange (ETDEWEB)

Grech, G. K.; Lawton, D. [Calgary Univ., AB (Canada)

2000-09-01

Vertical seismic profiling (VSP) and surface seismic data are used to image and locate hydrocarbon targets in the subsurface, hence the importance of assessing which formations exhibit seismic velocity anisotropy and quantify their parameters for use during seismic imaging. The purpose of the experiments described in this paper was to determine whether the multiple dipping thin shale beds overlying the target area in the Rocky Mountain Foothills in southern Alberta exhibit seismic velocity anisotropy and if so, how this phenomenon affects the image of the underlying target. Traveltime inversion of the first arrival data from the multi-offset VSP in the study area has revealed that the Cretaceous shales exhibit velocity anisotropy of about 10 degrees. For a target depth of 3000 m and moderate dips of 30 to 50 degrees in the anisotropic overburden, it would be reasonable to expect a lateral shift in the imaged location of the target of up to 300 m in the up-direction of overlying bedding. 8 refs., 9 figs.

Optimum energy levels and offsets for organic donor/acceptor binary photovoltaic materials and solar cells

International Nuclear Information System (INIS)

Sun, S.-S.

2005-01-01

Optimum frontier orbital energy levels and offsets of an organic donor/acceptor binary type photovoltaic material have been analyzed using classic Marcus electron transfer theory in order to achieve the most efficient photo induced charge separation. This study reveals that, an exciton quenching parameter (EQP) yields one optimum donor/acceptor frontier orbital energy offset that equals the sum of the exciton binding energy and the charge separation reorganization energy, where the photo generated excitons are converted into charges most efficiently. A recombination quenching parameter (RQP) yields a second optimum donor/acceptor energy offset where the ratio of charge separation rate constant over charge recombination rate constant becomes largest. It is desirable that the maximum RQP is coincidence or close to the maximum EQP. A third energy offset is also identified where charge recombination becomes most severe. It is desirable that the most severe charge recombination offset is far away from maximum EQP offset. These findings are very critical for evaluating and fine tuning frontier orbital energy levels of a donor/acceptor pair in order to realize high efficiency organic photovoltaic materials

Application of Cutting-Edge 3D Seismic Attribute Technology to the Assessment of Geological Reservoirs for CO2 Sequestration

Energy Technology Data Exchange (ETDEWEB)

Christopher Liner; Jianjun Zeng; Po Geng Heather King Jintan Li; Jennifer Califf; John Seales

2010-03-31

The goals of this project were to develop innovative 3D seismic attribute technologies and workflows to assess the structural integrity and heterogeneity of subsurface reservoirs with potential for CO{sub 2} sequestration. Our specific objectives were to apply advanced seismic attributes to aide in quantifying reservoir properies and lateral continuity of CO{sub 2} sequestration targets. Our study area is the Dickman field in Ness County, Kansas, a type locality for the geology that will be encountered for CO{sub 2} sequestration projects from northern Oklahoma across the U.S. midcontent to Indiana and beyond. Since its discovery in 1962, the Dickman Field has produced about 1.7 million barrels of oil from porous Mississippian carbonates with a small structural closure at about 4400 ft drilling depth. Project data includes 3.3 square miles of 3D seismic data, 142 wells, with log, some core, and oil/water production data available. Only two wells penetrate the deep saline aquifer. Geological and seismic data were integrated to create a geological property model and a flow simulation grid. We systematically tested over a dozen seismic attributes, finding that curvature, SPICE, and ANT were particularly useful for mapping discontinuities in the data that likely indicated fracture trends. Our simulation results in the deep saline aquifer indicate two effective ways of reducing free CO{sub 2}: (a) injecting CO{sub 2} with brine water, and (b) horizontal well injection. A tuned combination of these methods can reduce the amount of free CO{sub 2} in the aquifer from over 50% to less than 10%.

High-resolution mapping based on an Unmanned Aerial Vehicle (UAV) to capture paleoseismic offsets along the Altyn-Tagh fault, China.

Science.gov (United States)

Gao, Mingxing; Xu, Xiwei; Klinger, Yann; van der Woerd, Jerome; Tapponnier, Paul

2017-08-15

The recent dramatic increase in millimeter- to centimeter- resolution topographic datasets obtained via multi-view photogrammetry raises the possibility of mapping detailed offset geomorphology and constraining the spatial characteristics of active faults. Here, for the first time, we applied this new method to acquire high-resolution imagery and generate topographic data along the Altyn Tagh fault, which is located in a remote high elevation area and shows preserved ancient earthquake surface ruptures. A digital elevation model (DEM) with a resolution of 0.065 m and an orthophoto with a resolution of 0.016 m were generated from these images. We identified piercing markers and reconstructed offsets based on both the orthoimage and the topography. The high-resolution UAV data were used to accurately measure the recent seismic offset. We obtained the recent offset of 7 ± 1 m. Combined with the high resolution satellite image, we measured cumulative offsets of 15 ± 2 m, 20 ± 2 m, 30 ± 2 m, which may be due to multiple paleo-earthquakes. Therefore, UAV mapping can provide fine-scale data for the assessment of the seismic hazards.

Latest time-lapse seismic data from Sleipner yield new insights into CO2 plume development

NARCIS (Netherlands)

Chadwick, R.A.; Noy, D.; Arts, R.; Eiken, O.

2009-01-01

Since its inception in 1996, the CO2 injection operation at Sleipner has been monitored by 3D time-lapse seismic surveys. Striking images of the CO2 plume have been obtained, showing a multi-tier feature of high reflectivity, interpreted as arising from a number of thin layers of CO2 trapped beneath

Interseismic Coupling, Co- and Post-seismic Slip: a Stochastic View on the Northern Chilean Subduction Zone

Science.gov (United States)

Jolivet, R.; Duputel, Z.; Simons, M.; Jiang, J.; Riel, B. V.; Moore, A. W.; Owen, S. E.

2017-12-01

Mapping subsurface fault slip during the different phases of the seismic cycle provides a probe of the mechanical properties and the state of stress along these faults. We focus on the northern Chile megathrust where first order estimates of interseismic fault locking suggests little to no overlap between regions slipping seismically versus those that are dominantly aseismic. However, published distributions of slip, be they during seismic or aseismic phases, rely on unphysical regularization of the inverse problem, thereby cluttering attempts to quantify the degree of overlap between seismic and aseismic slip. Considering all the implications of aseismic slip on our understanding of the nucleation, propagation and arrest of seismic ruptures, it is of utmost importance to quantify our confidence in the current description of fault coupling. Here, we take advantage of 20 years of InSAR observations and more than a decade of GPS measurements to derive probabilistic maps of inter-seismic coupling, as well as co-seismic and post-seismic slip along the northern Chile subduction megathrust. A wide InSAR velocity map is derived using a novel multi-pixel time series analysis method accounting for orbital errors, atmospheric noise and ground deformation. We use AlTar, a massively parallel Monte Carlo Markov Chain algorithm exploiting the acceleration capabilities of Graphic Processing Units, to derive the probability density functions (PDF) of slip. In northern Chile, we find high probabilities for a complete release of the elastic strain accumulated since the 1877 earthquake by the 2014, Iquique earthquake and for the presence of a large, independent, locked asperity left untapped by recent events, north of the Mejillones peninsula. We evaluate the probability of overlap between the co-, inter- and post-seismic slip and consider the potential occurrence of slow, aseismic slip events along this portion of the subduction zone.

Co-seismic Earth’s rotation change caused by the 2012 Sumatra earthquake

Directory of Open Access Journals (Sweden)

Xu Changyi

2012-11-01

Full Text Available Earthquakes heavily deform the crust in the vicinity of the fault, which leads to mass redistribution in the earth interior. Then it will produce the change of the Earth’s rotation (polar motion and length of day due to the change of Earth inertial moment. This paper adopts the elastic dislocation to compute the co-seismic polar motion and variation in length of day (LOD caused by the 2011 Sumatra earthquake. The Earth’s rotational axis shifted about 1 mas and this earthquake decreased the length of day of 1 μs, indicating the tendency of earthquakes make the Earth rounder and to pull the mass toward the centre of the Earth. The result of variation in length of day is one order of magnitude smaller than the observed results that are available. We also compared the results of three fault models and find the co-seismic change is depended on the fault model.

Final report of a scalable, automated, semipermanent seismic array (SASSA) method for detecting CO₂ extent during geologic CO₂ injection

Energy Technology Data Exchange (ETDEWEB)

Burnison, Shaughn [University of North Dakota Energy & Environmental Research Center, Grand Forks, ND (United States); Livers-Douglas, Amanda [University of North Dakota Energy & Environmental Research Center, Grand Forks, ND (United States); Barajas-Olalde, Cesar [University of North Dakota Energy & Environmental Research Center, Grand Forks, ND (United States); Jin, Lu [University of North Dakota Energy & Environmental Research Center, Grand Forks, ND (United States); Vettleson, Heidi [University of North Dakota Energy & Environmental Research Center, Grand Forks, ND (United States); Hamiling, John [University of North Dakota Energy & Environmental Research Center, Grand Forks, ND (United States); Gorecki, Charles [University of North Dakota Energy & Environmental Research Center, Grand Forks, ND (United States)

2017-12-15

The scalable, automated, semipermanent seismic array (SASSA) project led and managed by the Energy & Environmental Research Center (EERC) was designed as a 3-year proof-of-concept study to evaluate and demonstrate an innovative application of the seismic method. The concept was to use a sparse surface array of 96 nodal seismic sensors paired with a single, remotely operated active seismic source at a fixed location to monitor for CO₂ saturation changes in a subsurface reservoir by processing the data for time-lapse changes at individual, strategically chosen reservoir reflection points. The combination of autonomous equipment and modern processing algorithms was used to apply the seismic method in a manner different from the normal paradigm of collecting a spatially dense data set to produce an image. It was used instead to monitor individual, strategically chosen reservoir reflection points for detectable signal character changes that could be attributed to the passing of a CO₂ saturation front or, possibly, changes in reservoir pressure. Data collection occurred over the course of 1 year at an oil field undergoing CO₂ injection for enhanced oil recovery (EOR) and focused on four overlapping “five-spot” EOR injector–producer patterns. Selection, procurement, configuration, installation, and testing of project equipment and collection of five baseline data sets were completed in advance of CO₂ injection within the study area. Weekly remote data collection produced 41 incremental time-lapse records for each of the 96 nodes. Validation was provided by two methods: 1) a conventional 2-D seismic line acquired through the center of the study area before injection started and again after the project ended and processed in a time-lapse manner and 2) by CO₂ saturation maps created from reservoir simulations based on injection and production history matching. Interpreted results were encouraging but mixed, with

Radiative forcing and temperature response to changes in urban albedos and associated CO2 offsets

International Nuclear Information System (INIS)

Menon, Surabi; Akbari, Hashem; Sednev, Igor; Levinson, Ronnen; Mahanama, Sarith

2010-01-01

The two main forcings that can counteract to some extent the positive forcings from greenhouse gases from pre-industrial times to present day are the aerosol and related aerosol-cloud forcings, and the radiative response to changes in surface albedo. Here, we quantify the change in radiative forcing and land surface temperature that may be obtained by increasing the albedos of roofs and pavements in urban areas in temperate and tropical regions of the globe by 0.1. Using the catchment land surface model (the land model coupled to the GEOS-5 Atmospheric General Circulation Model), we quantify the change in the total outgoing (outgoing shortwave+longwave) radiation and land surface temperature to a 0.1 increase in urban albedos for all global land areas. The global average increase in the total outgoing radiation was 0.5 W m -2 , and temperature decreased by ∼0.008 K for an average 0.003 increase in surface albedo. These averages represent all global land areas where data were available from the land surface model used and are for the boreal summer (June-July-August). For the continental US the total outgoing radiation increased by 2.3 W m -2 , and land surface temperature decreased by ∼0.03 K for an average 0.01 increase in surface albedo. Based on these forcings, the expected emitted CO 2 offset for a plausible 0.25 and 0.15 increase in albedos of roofs and pavements, respectively, for all global urban areas, was found to be ∼57 Gt CO 2 . A more meaningful evaluation of the impacts of urban albedo increases on global climate and the expected CO 2 offsets would require simulations which better characterize urban surfaces and represent the full annual cycle.

Co-Seismic Gravity Gradient Changes of the 2006-2007 Great Earthquakes in the Central Kuril Islands from GRACE Observations

Science.gov (United States)

Rahimi, A.; Shahrisvand, M.

2017-09-01

GRACE satellites (the Gravity Recovery And climate Experiment) are very useful sensors to extract gravity anomalies after earthquakes. In this study, we reveal co-seismic signals of the two combined earthquakes, the 2006 Mw8.3 thrust and 2007 Mw8.1 normal fault earthquakes of the central Kuril Islands from GRACE observations. We compute monthly full gravitational gradient tensor in the local north-east-down frame for Kuril Islands earthquakes without spatial averaging and de-striping filters. Some of gravitational gradient components (e.g. ΔVxx, ΔVxz) enhance high frequency components of the earth gravity field and reveal more details in spatial and temporal domain. Therefore, co-seismic activity can be better illustrated. For the first time, we show that the positive-negative-positive co-seismic ΔVxx due to the Kuril Islands earthquakes ranges from - 0.13 to + 0.11 milli Eötvös, and ΔVxz shows a positive-negative-positive pattern ranges from - 0.16 to + 0.13 milli Eötvös, agree well with seismic model predictions.

Modeling of time-lapse multi-scale seismic monitoring of CO2 injected into a fault zone to enhance the characterization of permeability in enhanced geothermal systems

Science.gov (United States)

Zhang, R.; Borgia, A.; Daley, T. M.; Oldenburg, C. M.; Jung, Y.; Lee, K. J.; Doughty, C.; Altundas, B.; Chugunov, N.; Ramakrishnan, T. S.

2017-12-01

Subsurface permeable faults and fracture networks play a critical role for enhanced geothermal systems (EGS) by providing conduits for fluid flow. Characterization of the permeable flow paths before and after stimulation is necessary to evaluate and optimize energy extraction. To provide insight into the feasibility of using CO2 as a contrast agent to enhance fault characterization by seismic methods, we model seismic monitoring of supercritical CO2 (scCO2) injected into a fault. During the CO2 injection, the original brine is replaced by scCO2, which leads to variations in geophysical properties of the formation. To explore the technical feasibility of the approach, we present modeling results for different time-lapse seismic methods including surface seismic, vertical seismic profiling (VSP), and a cross-well survey. We simulate the injection and production of CO2 into a normal fault in a system based on the Brady's geothermal field and model pressure and saturation variations in the fault zone using TOUGH2-ECO2N. The simulation results provide changing fluid properties during the injection, such as saturation and salinity changes, which allow us to estimate corresponding changes in seismic properties of the fault and the formation. We model the response of the system to active seismic monitoring in time-lapse mode using an anisotropic finite difference method with modifications for fracture compliance. Results to date show that even narrow fault and fracture zones filled with CO2 can be better detected using the VSP and cross-well survey geometry, while it would be difficult to image the CO2 plume by using surface seismic methods.

Policy development for biodiversity offsets: a review of offset frameworks.

Science.gov (United States)

McKenney, Bruce A; Kiesecker, Joseph M

2010-01-01

Biodiversity offsets seek to compensate for residual environmental impacts of planned developments after appropriate steps have been taken to avoid, minimize or restore impacts on site. Offsets are emerging as an increasingly employed mechanism for achieving net environmental benefits, with offset policies being advanced in a wide range of countries (i.e., United States, Australia, Brazil, Colombia, and South Africa). To support policy development for biodiversity offsets, we review a set of major offset policy frameworks-US wetlands mitigation, US conservation banking, EU Natura 2000, Australian offset policies in New South Wales, Victoria, and Western Australia, and Brazilian industrial and forest offsets. We compare how the frameworks define offset policy goals, approach the mitigation process, and address six key issues for implementing offsets: (1) equivalence of project impacts with offset gains; (2) location of the offset relative to the impact site; (3) "additionality" (a new contribution to conservation) and acceptable types of offsets; (4) timing of project impacts versus offset benefits; (5) offset duration and compliance; and (6) "currency" and mitigation replacement ratios. We find substantial policy commonalities that may serve as a sound basis for future development of biodiversity offsets policy. We also identify issues requiring further policy guidance, including how best to: (1) ensure conformance with the mitigation hierarchy; (2) identify the most environmentally preferable offsets within a landscape context; and (3) determine appropriate mitigation replacement ratios.

Rock formation characterization for CO2-EOR and carbon geosequestration; 3D seismic amplitude and coherency anomalies, Wellington Field, Kansas, USA

Science.gov (United States)

Ohl, D.; Raef, A.; Watnef, L.; Bhattacharya, S.

2011-01-01

In this paper, we present a workflow for a Mississipian carbonates characterization case-study integrating post-stack seismic attributes, well-logs porosities, and seismic modeling to explore relating changes in small-scale "lithofacies" properties and/or sub-seismic resolution faulting to key amplitude and coherency 3D seismic attributes. The main objective of this study is to put emphasis on reservoir characterization that is both optimized for and subsequently benefiting from pilot tertiary CO2-EOR in preparation for future carbon geosequestration in a depleting reservoir and a deep saline aquifer. The extracted 3D seismic coherency attribute indicated anomalous features that can be interpreted as a lithofacies change or a sub-seismic resolution faulting. A 2D finite difference modeling has been undertaken to understand and potentially build discriminant attributes to map structural and/or lithofacies anomalies of interest especially when embarking upon CO2-EOR and/or carbon sequestration monitoring and management projects. ?? 2011 Society of Exploration Geophysicists.

Prediction of calcite Cement Distribution in Shallow Marine Sandstone Reservoirs using Seismic Data

Energy Technology Data Exchange (ETDEWEB)

Bakke, N.E.

1996-12-31

This doctoral thesis investigates how calcite cemented layers can be detected by reflection seismic data and how seismic data combined with other methods can be used to predict lateral variation in calcite cementation in shallow marine sandstone reservoirs. Focus is on the geophysical aspects. Sequence stratigraphy and stochastic modelling aspects are only covered superficially. Possible sources of calcite in shallow marine sandstone are grouped into internal and external sources depending on their location relative to the presently cemented rock. Well data and seismic data from the Troll Field in the Norwegian North Sea have been analysed. Tuning amplitudes from stacks of thin calcite cemented layers are analysed. Tuning effects are constructive or destructive interference of pulses resulting from two or more closely spaced reflectors. The zero-offset tuning amplitude is shown to depend on calcite content in the stack and vertical stack size. The relationship is found by regression analysis based on extensive seismic modelling. The results are used to predict calcite distribution in a synthetic and a real data example. It is found that describing calcite cemented beds in shallow marine sandstone reservoirs is not a deterministic problem. Hence seismic inversion and sequence stratigraphy interpretation of well data have been combined in a probabilistic approach to produce models of calcite cemented barriers constrained by a maximum amount of information. It is concluded that seismic data can provide valuable information on distribution of calcite cemented beds in reservoirs where the background sandstones are relatively homogeneous. 63 refs., 78 figs., 10 tabs.

Atlas of Wenchuan-Earthquake Geohazards : Analysis of co-seismic and post-seismic Geohazards in the area affected by the 2008 Wenchuan Earthquake

NARCIS (Netherlands)

Tang, Chuan; van Westen, C.J.

2018-01-01

This atlas provides basic information and overviews of the occurrence of co-seismic landslides, the subsequent rainstorm-induced debris flows, and the methods used for hazard and risk assessment in the Wenchuan-earthquake affected area. The atlas pages are illustrated with maps, photos and graphs,

Influence of data irregularities on 3-D common offset migration; Influence d'irregularites dans l'echantillonnage des donnees sur la migration 3D par deport

Energy Technology Data Exchange (ETDEWEB)

Assouline, F.; Lailly, P. [Institut Francais du Petrole (IFP), 92 - Rueil-Malmaison (France); Assouline, F [Pau Univ., 64 (France)

2001-07-01

In 3-D seismic survey, offset is a vector characterized by the source-receiver distance and azimuth. Due to irregularities in the acquisition (for instance streamer feathering in marine acquisition) common offset data are not available and, in turn, 3-D common offset migration does not make sense any longer. We then introduce the concept of migration by offset class: it is a straightforward extension of common offset migration in which we migrate all traces that belong to a given offset class, namely all traces with offset close to a given one. The result of such a migration depends of course on how the offset class is constructed or, in other words, on what is meant with 'close '. The aim of this paper is to investigate by means of a 3-D numerical study how to design offset classes so as to obtain migrated images that can be interpreted without trouble (such an interpretation is a key element for a successful migration velocity analysis). We have to find a trade-off between two extremes: - a too loose offset class that would mix heterogeneous offsets (in particular mixing substantially different azimuths can be dangerous); - a too narrow offset class that would result in sparse seismic traces with, in turn, an inadequate coverage of the reflector. The regularity, within an offset class, of the offset variation as well as the one of the distribution of midpoints are parameters that can have a drastic influence on the quality of the migrated image. It is shown that migration by offset class appears as a robust procedure all the more than the offset varies slowly with the midpoint coordinate within an offset class. Besides, the smaller the mean offset norm, the lower is the contamination of the image due to the mixing of azimuths within an offset class. (authors)

Last Glacial Maximum CO2 and d13C successfully reconciled

NARCIS (Netherlands)

Bouttes, N.; Paillard, D.; Roche, D.M.V.A.P.; Brovkin, V.; Bopp, L.

2011-01-01

During the Last Glacial Maximum (LGM, ∼21,000 years ago) the cold climate was strongly tied to low atmospheric CO2 concentration (∼190 ppm). Although it is generally assumed that this low CO2 was due to an expansion of the oceanic carbon reservoir, simulating the glacial level

Seismic soil-structure interaction with consideration of spatial incoherence of seismic ground motions: A case study

Energy Technology Data Exchange (ETDEWEB)

Tseng, Wen S., E-mail: wen.tseng@rizzoassoc.com [Paul C. Rizzo Associates, Inc., Western Region, 2201 Broadway, Suite 400, Oakland, CA 94612 (United States); Lilhanand, Kiat; Hamasaki, Don; Garcia, Julio A. [Paul C. Rizzo Associates, Inc., Western Region, 2201 Broadway, Suite 400, Oakland, CA 94612 (United States); Srinivasan, Ram [AREVA, NP, Inc., 6399 San Ignacio Avenue, San Jose, CA 95119 (United States)

2014-04-01

This paper presents a case study of seismic soil-structure interaction (SSI) analysis with consideration of spatial incoherence of seismic input ground motions. The SSI analyses were performed using the SASSI computer program for the Auxiliary Control Building (ACB) structure of an existing nuclear power plant on a hard rock site located in the Center and Eastern United States (CEUS) region. The incoherent seismic input motions for the hard rock site used for the analyses were generated using the computer program INCOH that works together with SASSI. The objective of the analyses was to generate maximum seismic response parameters for assessment of potential impact of newly developed site-specific (ground motion) response spectra (SSRS) on the seismic design of the ACB and potential benefits that could be gained by considering spatial incoherence of seismic input motions. Maximum seismic response values for selected response parameters of interest were generated with both SSRS-compatible coherent and incoherent seismic input motions. Comparisons were made of the corresponding maximum response parameter values and in-structure (acceleration) response spectra (ISRS) generated for both the coherent and incoherent motion inputs. These comparisons indicate that, by incorporating incoherence of ground motions in the seismic input, the maximum response values reduces and the ISRS peak amplitudes in the high frequency range (>10 Hz) also reduce from the corresponding response values resulting from the coherent motion input. The amount of ISRS-amplitude reduction increases as the spectral frequency increases, as expected. Such reductions can be as much as 20–50%. This case study demonstrates that, for a CEUS hard rock site where relatively high high-frequency in the seismic input response spectra exist, consideration of spatial incoherence of input motions would result in substantial benefits in reducing the high-frequency seismic responses. Such benefits are especially

Fluid injection and induced seismicity

Science.gov (United States)

Kendall, Michael; Verdon, James

2016-04-01

The link between fluid injection, or extraction, and induced seismicity has been observed in reservoirs for many decades. In fact spatial mapping of low magnitude events is routinely used to estimate a stimulated reservoir volume. However, the link between subsurface fluid injection and larger felt seismicity is less clear and has attracted recent interest with a dramatic increase in earthquakes associated with the disposal of oilfield waste fluids. In a few cases, hydraulic fracturing has also been linked to induced seismicity. Much can be learned from past case-studies of induced seismicity so that we can better understand the risks posed. Here we examine 12 case examples and consider in particular controls on maximum event size, lateral event distributions, and event depths. Our results suggest that injection volume is a better control on maximum magnitude than past, natural seismicity in a region. This might, however, simply reflect the lack of baseline monitoring and/or long-term seismic records in certain regions. To address this in the UK, the British Geological Survey is leading the deployment of monitoring arrays in prospective shale gas areas in Lancashire and Yorkshire. In most cases, seismicity is generally located in close vicinity to the injection site. However, in some cases, the nearest events are up to 5km from the injection point. This gives an indication of the minimum radius of influence of such fluid injection projects. The most distant events are never more than 20km from the injection point, perhaps implying a maximum radius of influence. Some events are located in the target reservoir, but most occur below the injection depth. In fact, most events lie in the crystalline basement underlying the sedimentary rocks. This suggests that induced seismicity may not pose a leakage risk for fluid migration back to the surface, as it does not impact caprock integrity. A useful application for microseismic data is to try and forecast induced seismicity

Maximum torque per ampere control of sensorless induction motor drives with dc offset and parameter compensation

International Nuclear Information System (INIS)

Markadeh, Gholamreza Arab; Hajian, Masood; Soltani, Jafar; Hosseinia, Saeed

2010-01-01

Field orientation control of induction machine (IM) drives is a well-known strategy which has a fast dynamic response. In this paper, the direct rotor flux field orientation control of speed sensorless IM drive is presented. A two level space vector modulation inverter is employed to generate the command stator voltage. In proposed control scheme, a maximum torque per ampere strategy is achieved using a so-called fast flux search method. Based on this method, for a given load torque and rotor speed, the magnitude of rotor reference flux is adjusted step by step until the effective value of stator current becomes minimized finally. In addition, using the IM fifth order model in the stationary reference frame, a nonlinear rotor flux observer is developed which is also capable of motor resistances and rotor speed simultaneously estimation. Moreover, a useful method is introduced for dc offset compensation which is a major problem of ac drives especially at low speeds. The proposed control idea is experimentally implemented in real time using a CPLD board synchronized with a personal computer. Simulation and experimental results are finally presented to confirm the validity and effectiveness of the proposed method.

Estimates of Future Supply of International Greenhouse Gas Offsets: A Critical Review

Energy Technology Data Exchange (ETDEWEB)

Erickson, Peter; Lazarus, Michael (Stockholm Environment Inst. (United States)), e-mail: mlaz@sei-us.org; Kelly, Alexia (World Resources Inst., (United States))

2010-07-01

This report reviews estimates of the projected availability (i.e., supply) of international offsets, evaluates the various methods used and outlines factors that should be incorporated into future analyses of international offset supply and quality. U.S. policymakers have relied on offsets from developing countries as a primary form of cost containment in proposed cap-and-trade legislation. These legislative proposals allow for emitters to use up to 1.5 billion tons CO{sub 2}e of offsets from developing countries to meet their annual compliance obligations. In this paper, we review estimates of the projected availability (i.e., supply) of international offsets, and evaluate the various methods used. We find that: (1) Estimates of supply of international offsets to global markets vary widely, with estimates differing by billions of tons CO{sub 2}e annually in 2020; (2) Despite the variation, existing studies suggest that by 2020 gross international offset supply will likely exceed U.S. demand for international offsets under current Congressional cap-and-trade designs; (3) Competition with governments and entities with emission reduction obligations (e.g. the EU), as well as with policies and measures undertaken by developing countries as part of their own mitigation contributions, could reduce the net offset supply available to U.S. entities; and (4) Several important offset program design and market factors that are central to future offset markets and credit issuance (e.g., sources of offset supply, program stringency and crediting methods, establishment of international governance and market structures) have yet to be systematically considered in offset supply assessments. This paper outlines factors that should be incorporated into future analyses of international offset supply and quality. 7 Such analyses could prove particularly germane as policy makers continue to deliberate on the role of international offsets, including whether and how to recognize credits

Implications of seismic reflection and potential field geophysical data on the structural framework of the Yucca Mountain--Crater Flat region, Nevada

International Nuclear Information System (INIS)

Brocher, T.M.; Langenheim, V.E.; Hunter, W.C.

1998-01-01

Seismic reflection and gravity profiles collected across Yucca Mountain, Nevada, together with geologic data, provide evidence against proposed active detachment faults at shallow depth along the pre-Tertiary-Tertiary contact beneath this potential repository for high-level nuclear waste. The new geophysical data show that the inferred pre-Tertiary-Tertiary contact is offset by moderate-to-high-angle faults beneath Crater Flat and Yucca Mountain, and thus this shallow surface cannot represent an active detachment surface. The reflection lines reveal that the Amargosa Desert rift zone is an asymmetric half-graben having a maximum depth of about 4 km and a width of about 25 km. The east-dipping Bare Mountain fault that bounds this graben to the west can be traced by seismic reflection data to a depth of at least 3.5 km and possibly as deep as 6 km, with a constant dip of 64 degree ± 5 degree. Along the profile the transition from east- to west-dipping faults occurs at or just west of the Solitario Canyon fault, which bounds the western side of Yucca Mountain. The interaction at depth of these east- and west-dipping faults, having up to hundreds of meters offset, is not imaged by the seismic reflection profile. Understanding potential seismic hazards at Yucca Mountain requires knowledge of the subsurface geometry of the faults near Yucca Mountain, since earthquakes generally nucleate and release the greatest amount of their seismic energy at depth. The geophysical data indicate that many fault planes near the potential nuclear waste facility dip toward Yucca Mountain, including the Bare Mountain range-front fault and several west-dipping faults east of Yucca Mountain. Thus, earthquake ruptures along these faults would lie closer to Yucca Mountain than is often estimated from their surface locations and could therefore be more damaging

Temperature Induced Voltage Offset Drifts in Silicon Carbide Pressure Sensors

Science.gov (United States)

Okojie, Robert S.; Lukco, Dorothy; Nguyen, Vu; Savrun, Ender

2012-01-01

We report the reduction of transient drifts in the zero pressure offset voltage in silicon carbide (SiC) pressure sensors when operating at 600 C. The previously observed maximum drift of +/- 10 mV of the reference offset voltage at 600 C was reduced to within +/- 5 mV. The offset voltage drifts and bridge resistance changes over time at test temperature are explained in terms of the microstructure and phase changes occurring within the contact metallization, as analyzed by Auger electron spectroscopy and field emission scanning electron microscopy. The results have helped to identify the upper temperature reliable operational limit of this particular metallization scheme to be 605 C.

A world-class target for ICDP drilling at Lake Nam Co, Tibetan Plateau, China: progresses and perspectives

Science.gov (United States)

Zhu, L.; Wang, J.; Daut, G.; Spiess, V.; Haberzettl, T.; Schulze, N.; Ju, J.; Lü, X.; Bergmann, F.; Haberkern, J.; Schwalb, A.; Mäusbacher, R.

2017-12-01

Lake Nam Co (ca. 2000 km2, 4718 m a.s.l., maximum depth: 100 m) is located at the interaction zone of the Westerlies and the Indian monsoon on the central Tibetan Plateau. It was part of a mega-lake during Marine Isotope Stage (MIS) 3 before the Last Glacial Maximum. A long term sedimentary record from Nam Co could therefore provide an excellent paleo-environmental sequence for regional and global comparative studies. This will to deepen our understanding of large scale atmospheric circulation shifts and the environmental links between the Tibetan Plateau at low latitudes and the North Atlantic region at high latitudes. A Nam Co deep drilling will fill the gap in two large scale ICDP/IODP drilling transects (N-S: Lake Baikal, Lake Qinghai, Bay of Bengal; W-E: Lake Van, Lake Issyk-Kul, South China Sea, Lake Towuti), which will show the great significance of monsoon dynamics on a long-term scale. Multidisciplinary researches have been conducted since 2005 by a Sino-German cooperative team. The progresses during the last decade are: 1) Detailed bathymetric surveying, including a shallow sediment profiler investigation (Innomar SES 2000 light, ca. 30 m sediment penetration); 2) Paleo-environmental reconstructions covering the past 24 ka; 3) Modern sediment distribution covering the entire lake; 4) Monitoring including water temperature profiles, sediment traps, seasonal airborne pollen collection; 5) Deep seismic survey penetrating up to 800 meters of lake sediments. Based on sediment rates from reference core NC08/01, seismic results show that an age of 500 ka may be reached at 500 m, and >1 Ma at the observed base. Faulting can be clearly detected in the seismic profiles, especially from MIS 5 to early Holocene, and shows the characteristics of normal faults or strike-slip faults. Both rotation of the layers and the close spacing, along with negative and positive offsets of the faults make a transtensional origin of the basin likely. An ICDP workshop proposal was

co-seismic grace gravity based 11-layered 3-d thrust fault model for ...

Indian Academy of Sciences (India)

30

It honours co-seismic deformation of ocean surface, ocean ... has caused great damage (Sumatra earthquake 2004 Wikipedia) when the Indian Plate ..... Gokula, A P, Sastry R G (2015a) Gravitational attraction of a vertical pyramid model of flat ... Journal. 14, 1-21. Lay T, Kanamori H, Ammon CJ, Nettles M, Ward SN, Aster ...

Seismic facies analysis from pre-stack data using self-organizing maps

International Nuclear Information System (INIS)

Kourki, Meysam; Ali Riahi, Mohammad

2014-01-01

In facies analysis, seismic data are clustered in different groups. Each group represents subsurface points with similar physical properties. Different groups can be related to differences in lithology, physical properties of rocks and fluid changes in the rocks. The supervised and unsupervised data clustering are known as two types of clustering architecture. In supervised clustering, the number of clusters is predefined, while in unsupervised clustering, a collection of patterns partitions into groups without predefined clusters. In this study, the pre-stack data clustering is used for seismic facies analysis. In this way, a horizon was selected from pre-stack data, followed by sorting of data using offset. A trace associated with each CDP is constructed, for which the first and second samples are related to the first and second offsets, respectively. The created trace is called consolidated trace which is characteristic of subsurface points. These consolidated traces are clustered by using self-organizing maps (SOM). In proposed pre-stack seismic data clustering, points with similar physical properties are placed in one cluster. Seismic data associated with hydrocarbon reservoirs have very different characteristics that are easily recognized. The efficiency of the proposed method was tested on both synthetic and real seismic data. The results showed that the algorithm improves the data classification and the points of different properties are noticeable in final maps. (paper)

Seismic Linear Noise Attenuation with Use of Radial Transform

Science.gov (United States)

Szymańska-Małysa, Żaneta

2018-03-01

One of the goals of seismic data processing is to attenuate the recorded noise in order to enable correct interpretation of the image. Radial transform has been used as a very effective tool in the attenuation of various types of linear noise, both numerical and real (such as ground roll, direct waves, head waves, guided waves etc). The result of transformation from offset - time (X - T) domain into apparent velocity - time (R - T) domain is frequency separation between reflections and linear events. In this article synthetic and real seismic shot gathers were examined. One example was targeted at far offset area of dataset where reflections and noise had similar apparent velocities and frequency bands. Another example was a result of elastic modelling where linear artefacts were produced. Bandpass filtering and scaling operation executed in radial domain attenuated all discussed types of linear noise very effectively. After noise reduction all further processing steps reveal better results, especially velocity analysis, migration and stacking. In all presented cases signal-to-noise ratio was significantly increased and reflections covered previously by noise were revealed. Power spectra of filtered seismic records preserved real dynamics of reflections.

Maximum spectral demands in the near-fault region

Science.gov (United States)

Huang, Yin-Nan; Whittaker, Andrew S.; Luco, Nicolas

2008-01-01

The Next Generation Attenuation (NGA) relationships for shallow crustal earthquakes in the western United States predict a rotated geometric mean of horizontal spectral demand, termed GMRotI50, and not maximum spectral demand. Differences between strike-normal, strike-parallel, geometric-mean, and maximum spectral demands in the near-fault region are investigated using 147 pairs of records selected from the NGA strong motion database. The selected records are for earthquakes with moment magnitude greater than 6.5 and for closest site-to-fault distance less than 15 km. Ratios of maximum spectral demand to NGA-predicted GMRotI50 for each pair of ground motions are presented. The ratio shows a clear dependence on period and the Somerville directivity parameters. Maximum demands can substantially exceed NGA-predicted GMRotI50 demands in the near-fault region, which has significant implications for seismic design, seismic performance assessment, and the next-generation seismic design maps. Strike-normal spectral demands are a significantly unconservative surrogate for maximum spectral demands for closest distance greater than 3 to 5 km. Scale factors that transform NGA-predicted GMRotI50 to a maximum spectral demand in the near-fault region are proposed.

Kinematics of reflections in subsurface offset and angle-domain image gathers

Science.gov (United States)

Dafni, Raanan; Symes, William W.

2018-05-01

Seismic migration in the angle-domain generates multiple images of the earth's interior in which reflection takes place at different scattering-angles. Mechanically, the angle-dependent reflection is restricted to happen instantaneously and at a fixed point in space: Incident wave hits a discontinuity in the subsurface media and instantly generates a scattered wave at the same common point of interaction. Alternatively, the angle-domain image may be associated with space-shift (regarded as subsurface offset) extended migration that artificially splits the reflection geometry. Meaning that, incident and scattered waves interact at some offset distance. The geometric differences between the two approaches amount to a contradictory angle-domain behaviour, and unlike kinematic description. We present a phase space depiction of migration methods extended by the peculiar subsurface offset split and stress its profound dissimilarity. In spite of being in radical contradiction with the general physics, the subsurface offset reveals a link to some valuable angle-domain quantities, via post-migration transformations. The angle quantities are indicated by the direction normal to the subsurface offset extended image. They specifically define the local dip and scattering angles if the velocity at the split reflection coordinates is the same for incident and scattered wave pairs. Otherwise, the reflector normal is not a bisector of the opening angle, but of the corresponding slowness vectors. This evidence, together with the distinguished geometry configuration, fundamentally differentiates the angle-domain decomposition based on the subsurface offset split from the conventional decomposition at a common reflection point. An asymptotic simulation of angle-domain moveout curves in layered media exposes the notion of split versus common reflection point geometry. Traveltime inversion methods that involve the subsurface offset extended migration must accommodate the split geometry

Preliminary review and summary of the potential for tectonic, seismic, and volcanic activity at the Nevada Test Site defense waste disposal site

International Nuclear Information System (INIS)

Metcalf, L.A.

1983-03-01

A change from compressional to extensional tectonics, which occurred about 17 m.y. ago, marks the emergence of the present tectonic regime in the southern Great Basin. Crustal extension is continuing at the present time, oriented in a NW-SE direction in the NTS region. Concurrently with the onset of crustal extension a system of NW- and NE-trending shear zones developed, along which mutual offset has occurred. Present seismic and tectonic activity in the NTS region is concentrated along the intersections of the shear zones and in areas of deep basin formation. Natural historic seismicity of the NTS region has been low to moderate. Seismic hazard assessments suggest a maximum magnitude 6-7 earthquake, associated with a maximum peak acceleration of 0.7 to 0.9 g, is probable for the NTS. A return period of 12,700 to 15,000 y for the maximum peak acceleration indicates a relatively low seismic hazard. Silicic volcanism in the NTS region was active from 16 to 6 m.y. ago, followed by a transition to basaltic volcanism. The tectonic settings most favorable for Quaternary basaltic activity are areas of young basin-range extension, caldera ring fracture zones, and intersections of conjugate shear zones. Probability calculations for the Yucca Mountain waste repository result in a volcanic disruption hazard of 10 - 8 to 10 - 9 /y. This value is extremely low and is probably representative of the hazard at Frenchman Flat. However, due to its tectonic setting, Frenchman Flat may be an area conducive to future basaltic volcanism; further investigation is needed to properly assess volcanic hazard

Motion of the Bird's Head Block and co-seismic deformation from GPS data

Science.gov (United States)

Tikku, A. A.; Subarya, C.; N/A, M.; McCaffrey, R.; Genrich, J.

2006-05-01

The Bird's Head region of Eastern Indonesia, comprising the western end of New Guinea, behaves as an independent block at a juncture of subduction zones. It is bound on the north by the Manokwari and New Guinea Trenches, on the west by the Sorong fault, on the southwest by the Seram Trough, and on the east and southeast by the Lowland fault. Previous analysis of regional campaign global positioning system [GPS] data collected between 1991 and 1997 revealed rotation of the Bird's Head Block and high shear rates between the Pacific and Australian plates accommodated within the block. We have collected and analyzed additional regional campaign GPS data collected between 1998 and 2005, which includes data from newly established stations in the vicinity of the Cenderwasih Bay and Lowlands fault. During this span of time there were four large (Mw greater than 7.0) earthquakes in the region: a magnitude Mw=7.5 on a historically inactive NW-SE trending strike-slip fault bounding the western end of the Cenderwasih Bay on October 10th, 2002, two events, with magnitudes Mw=7.0 and 7.3, separated by a time span of two days (February 5th and 7th 2004) and a distance of ~100 km on the NE-SW trending Lowlands fault, and a third event (Mw=7.1) on November 26th 2004, coincident with the location of the February 5th 2004 event on the Lowlands fault. Destruction and fatalities were associated with all these large earthquakes. The Lowlands fault is a known seismically active fault. The historically inactive fault active that ruptured in 2002 is in the middle of the Bird's Head Block and disrupted the collection of a long seismically quiescent time-series of deformation within the block, but we have been able to constrain the co-seismic slip on this fault with the GPS data and modeling, and here present these results. We have also estimated the corruption of the co-seismic deformation from the 2002 and 2004 earthquakes and removed these from the campaign data to here present estimates

Co-seismic response of water level in the Jingle well (China) associated with the Gorkha Nepal (Mw 7.8) earthquake

Science.gov (United States)

He, Anhua; Fan, Xuefang; Zhao, Gang; Liu, Yang; Singh, Ramesh P.; Hu, Yuliang

2017-09-01

Changes in co-seismic water levels associated with the Gorkha Nepal earthquake (25 April 2015, Mw 7.8) were recorded in the Jingle well in Shanxi Province China (longitude E112.03°, latitude N38.35°, about 2769 km from epicenter). Based on the observed water levels, we clearly identified signals relating to P, S and surface waves. However, the water temperature recorded at a depth of 350 m shows no co-seismic changes. A spectrum analysis of co-seismic variations of water level shows that the oscillation frequency and amplitude of water level in the borehole are determined by the natural frequency of the borehole, which is not associated with the propagation of seismic waves. The borehole-aquifer system shows a large amplification associated with ground vibrations generated by earthquakes. Considering the local hydro-geological map and the temperature gradient of the Jingle well, a large volume ;groundwater reservoir; model can be used to explain these processes. Due to seismic wave propagation, the volume of a well-confined aquifer expands and contracts forming fractures that change the water flow. In the well-confined aquifer, water levels oscillate simultaneously with high amplitude ground shaking during earthquakes. However, the water in the center of the ;underground reservoir; remains relatively stationary, without any changes in the water temperature. In addition, a possible precursor wave is recorded in the water level at the Jingle well prior to the Gorkha earthquake.

Lithofacies and associated reservoir properties co-simulations constraint by seismic data; Cosimulations de lithofacies et de proprietes reservoirs associees contraintes par les donnees sismiques

Energy Technology Data Exchange (ETDEWEB)

Fichtl, P.

1998-01-19

Integration of data different sources and nature leads to more accurate reservoir models, useful for controlling fluid and assessing final uncertainties. In this frame, this thesis presents a new technique for co-simulating in 3D two high resolution properties - one categorical, one continuous - conditionally to well information and under the constraint of seismic data. This technique could be applied to simulate lithofacies and related reservoir properties like acoustic impedances or porosities. The proposed algorithm combines a non-parametric approach for the categorical variable and a parametric approach for the continuous variable through a sequential co-simulation. The co-simulation process is divided in two steps: in the first step, the lithofacies is co-simulated with the seismic information by a sequential indicator co-simulation with co-kriging and, in the second step, the reservoir property of interest is simulated from the previously co-simulated lithofacies using sequential Gaussian (co- )simulation or P-field simulation. A validation study on a synthetic but realistic model shows that this technique provides alternative models of lithofacies and associated high resolution acoustic impedances consistent with the seismic data. The seismic information constraining the co-simulations contributes to reduce the uncertainties for the lithofacies distribution at the reservoir level. In some case, a Markov co-regionalization model can be used for simplifying the inference and modelling of the cross-covariances; finally, the co-simulation algorithm was applied to a 3D real case study with objective the joint numerical modelling of lithofacies and porosity in a fluvial channel reservoir. (author) 88 refs.

Feasibility of 4D multicomponent seismic methods for monitoring CO2 storage in the Redwater Leduc Reef, Alberta

Energy Technology Data Exchange (ETDEWEB)

Sodagar, Taher M.; Lawton, Don C. [University of Calgary, Calgary, Alberta (Canada)], email: tmysodag@ucalgary.ca

2011-07-01

The study area lies northeast of Edmonton, Alberta, in the Redwater region. The Redwater reef complex is roughly triangular and has an area of about 527 km2. It is found at a depth of about 1000 m and its thickness varies from 160 to 300 m. The main task of the study was a mapping, based on seismic character, of the facies variations that are found in the Redwater Leduc reef and a characterization of the reef members and formations below the reef with the help of a 3D geological model of the southern margin of the Redwater reef. A major goal targeted the Upper Leduc member interval, where time-lapse 3D multicomponent seismic modeling with 40% CO2 saturation was performed. Results showed fairly good amplitude differences at the top and base of this interval; this confirmed that the CO2 saturation within the Redwater reef can be monitored by repeated 3D multicomponent seismic surveys.

Induced Seismicity Monitoring System

Science.gov (United States)

Taylor, S. R.; Jarpe, S.; Harben, P.

2014-12-01

There are many seismological aspects associated with monitoring of permanent storage of carbon dioxide (CO2) in geologic formations. Many of these include monitoring underground gas migration through detailed tomographic studies of rock properties, integrity of the cap rock and micro seismicity with time. These types of studies require expensive deployments of surface and borehole sensors in the vicinity of the CO2 injection wells. Another problem that may exist in CO2 sequestration fields is the potential for damaging induced seismicity associated with fluid injection into the geologic reservoir. Seismic hazard monitoring in CO2 sequestration fields requires a seismic network over a spatially larger region possibly having stations in remote settings. Expensive observatory-grade seismic systems are not necessary for seismic hazard deployments or small-scale tomographic studies. Hazard monitoring requires accurate location of induced seismicity to magnitude levels only slightly less than that which can be felt at the surface (e.g. magnitude 1), and the frequencies of interest for tomographic analysis are ~1 Hz and greater. We have developed a seismo/acoustic smart sensor system that can achieve the goals necessary for induced seismicity monitoring in CO2 sequestration fields. The unit is inexpensive, lightweight, easy to deploy, can operate remotely under harsh conditions and features 9 channels of recording (currently 3C 4.5 Hz geophone, MEMS accelerometer and microphone). An on-board processor allows for satellite transmission of parameter data to a processing center. Continuous or event-detected data is kept on two removable flash SD cards of up to 64+ Gbytes each. If available, data can be transmitted via cell phone modem or picked up via site visits. Low-power consumption allows for autonomous operation using only a 10 watt solar panel and a gel-cell battery. The system has been successfully tested for long-term (> 6 months) remote operations over a wide range

Input for seismic hazard assessment using Vrancea seismic source region

International Nuclear Information System (INIS)

Ivan, Iren-Adelina; Enescu, B.D.; Pantea, A.

1998-01-01

We use an extended and combined data base including historical and modern, qualitative and quantitative data, i.e., more than 25 events during the period 1790 - 1990 with epicentral/maximum intensities ranging from X to V degree (MSK scale), the variation interval of isoseismal curves ranging from IX th to III rd degree. The data set was analysed using both the sum phasor techniques of Ridelek and Sacks (1984) for different magnitudes and depth intervals and the Stepp's method. For the assessment of seismic hazard we need a pattern of seismic source regions including an estimation for the maximum expected magnitude and the return period for the studied regions. Another necessary step in seismic hazard assessment is to develop attenuation relationships specific to a seismogenic zone, particularly to sub-crustal earthquakes of Vrancea region. The conceptual frame involves the use of appropriate decay models and consideration of the randomness in the attenuation, taking into account the azimuthal variation of the isoseist shapes. (authors)

Seismic refraction survey of the ANS preferred site

Energy Technology Data Exchange (ETDEWEB)

Davis, R.K. (Automated Sciences Group, Inc., Oak Ridge, TN (United States)); Hopkins, R.A. (Marrich, Inc., Knoxville, TN (United States)); Doll, W.E. (Oak Ridge National Lab., TN (United States))

1992-02-01

Between September 19, 1991 and October 8, 1991 personnel from Martin Marietta Energy Systems, Inc. (Energy Systems), Automated Sciences Group, Inc., and Marrich, Inc. performed a seismic refraction survey at the Advanced Neutron Source (ANS) preferred site. The purpose of this survey was to provide estimates of top-of-rock topography, based on seismic velocities, and to delineate variations in rock and soil velocities. Forty-four seismic refraction spreads were shot to determine top-of-rock depths at 42 locations. Nine of the seismic spreads were shot with long offsets to provide 216 top-of-rock depths for 4 seismic refraction profiles. The refraction spread locations were based on the grid for the ANS Phase I drilling program. Interpretation of the seismic refraction data supports the assumption that the top-of-rock surface generally follows the local topography. The shallow top-of-rock interface interpreted from the seismic refraction data is also supported by limited drill information at the site. Some zones of anomalous data are present that could be the result of locally variable weathering, a localized variation in shale content, or depth to top-of-rock greater than the site norm.

Seismic Structure of the Oceanic Plate Entering the Central Part of the Japan Trench Obtained from Ocean-Bottom Seismic Data

Science.gov (United States)

Ohira, A.; Kodaira, S.; Fujie, G.; No, T.; Nakamura, Y.; Miura, S.

2017-12-01

In trench-outer rise regions, the normal faults develop due to the bending of the incoming plate, which cause numerous normal-faulting earthquakes and systematic structural variations toward trenches. In addition to the effects on the bend-related normal fault, structural variations which are interpreted to be attributed to pseudofaults, a fracture zone, and petit-spot volcanic activities are observed in the oceanic plate entering the central part of the Japan Trench, off Miyagi. In May-June 2017, to understand detail structural variations and systematic structural changes of the oceanic plate toward the trench, we conducted an active-source seismic survey off Miyagi using R/V Kaimei, a new research vessel of JAMSTEC. Along a 100 km-long seismic profile which is approximately perpendicular to the trench axis, we deployed 40 ocean-bottom seismometers at intervals of 2 km and fired a large airgun array (total volume 10,600 cubic inches) with 100 m shooting intervals. Multi-channel seismic reflection data were also collected along the profile. On OBS records we observed refractions from the sedimentary layer and the oceanic crust (Pg), wide-angle reflections from the crust-mantle boundary (PmP), and refractions from the uppermost mantle (Pn). Pg is typically observed clearly at near offsets (approximately 20 km) but it highly attenuates at far offsets (> 20 km). A triplication of Pg-PmP-Pn with strong amplitudes is observed at ranges from 30 km to 60 km offsets. Pn is typically weak and its apparent velocity is approximately 8 km/sec. High attenuation of Pg and weak Pn may indicate the complex crustal structure related to petit-spot volcanic activities and/or a fracture zone, which are recognized in bathymetry data around the profile.

What controls the maximum magnitude of injection-induced earthquakes?

Science.gov (United States)

Eaton, D. W. S.

2017-12-01

Three different approaches for estimation of maximum magnitude are considered here, along with their implications for managing risk. The first approach is based on a deterministic limit for seismic moment proposed by McGarr (1976), which was originally designed for application to mining-induced seismicity. This approach has since been reformulated for earthquakes induced by fluid injection (McGarr, 2014). In essence, this method assumes that the upper limit for seismic moment release is constrained by the pressure-induced stress change. A deterministic limit is given by the product of shear modulus and the net injected fluid volume. This method is based on the assumptions that the medium is fully saturated and in a state of incipient failure. An alternative geometrical approach was proposed by Shapiro et al. (2011), who postulated that the rupture area for an induced earthquake falls entirely within the stimulated volume. This assumption reduces the maximum-magnitude problem to one of estimating the largest potential slip surface area within a given stimulated volume. Finally, van der Elst et al. (2016) proposed that the maximum observed magnitude, statistically speaking, is the expected maximum value for a finite sample drawn from an unbounded Gutenberg-Richter distribution. These three models imply different approaches for risk management. The deterministic method proposed by McGarr (2014) implies that a ceiling on the maximum magnitude can be imposed by limiting the net injected volume, whereas the approach developed by Shapiro et al. (2011) implies that the time-dependent maximum magnitude is governed by the spatial size of the microseismic event cloud. Finally, the sample-size hypothesis of Van der Elst et al. (2016) implies that the best available estimate of the maximum magnitude is based upon observed seismicity rate. The latter two approaches suggest that real-time monitoring is essential for effective management of risk. A reliable estimate of maximum

The role of the 2008 Mw 7.9 Wenchuan earthquake in topographic evolution: seismically induced landslides and the associated isostatic response

Science.gov (United States)

Ren, Z.; Zhang, Z.; Zhang, H.; Zheng, W.; Zhang, P. Z.

2017-12-01

The widely held understanding that reverse-faulting earthquakes play an important role in building mountains has been challenged by recent studies suggesting that co-seismic landslides of the 2008 Mw 7.9 Wenchuan earthquake led to a net co-seismic lowering of surface height. We use precise estimates of co-seismic landslide volumes to calculate the long-term isostatic response to landsliding during the 2008 Wenchuan earthquake. The total isostatic respond volume is 2.0 km3 which did not change much associated with thickness of Te, however, the distribution of the rebound changes associated with thickness of Te. The total co-seismic mass change could be 1.8 km3. The maximum isostatic response due to Wenchuan earthquake may have been as high as 0.9 meters in the highest Pengguan massif of the central Longmen Shan. We also find that the average net uplift is 0.16 meters within the total landslide region due to the Wenchuan earthquake. Our findings suggest that the local topographic evolution of the middle Longmen Shan region is closely related to repeated tectonic events such as the 2008 Wenchuan Earthquake.

Seismic data two-step recovery approach combining sparsity-promoting and hyperbolic Radon transform methods

International Nuclear Information System (INIS)

Wang, Hanchuang; Chen, Shengchang; Ren, Haoran; Liang, Donghui; Zhou, Huamin; She, Deping

2015-01-01

In current research of seismic data recovery problems, the sparsity-promoting method usually produces an insufficient recovery result at the locations of null traces. The HRT (hyperbolic Radon transform) method can be applied to problems of seismic data recovery with approximately hyperbolic events. Influenced by deviations of hyperbolic characteristics between real and ideal travel-time curves, some spurious events are usually introduced and the recovery effect of intermediate and far-offset traces is worse than that of near-offset traces. Sparsity-promoting recovery is primarily dependent on the sparsity of seismic data in the sparse transform domain (i.e. on the local waveform characteristics), whereas HRT recovery is severely affected by the global characteristics of the seismic events. Inspired by the above conclusion, a two-step recovery approach combining sparsity-promoting and time-invariant HRT methods is proposed, which is based on both local and global characteristics of the seismic data. Two implementation strategies are presented in detail, and the selection criteria of the relevant strategies is also discussed. Numerical examples of synthetic and real data verify that the new approach can achieve a better recovery effect by simultaneously overcoming the shortcomings of sparsity-promoting recovery and HRT recovery. (paper)

Improving the Monitoring, Verification, and Accounting of CO{sub 2} Sequestered in Geologic Systems with Multicomponent Seismic Technology and Rock Physics Modeling

Energy Technology Data Exchange (ETDEWEB)

Alkan, Engin; DeAngelo, Michael; Hardage, Bob; Sava, Diana; Sullivan, Charlotte; Wagner, Donald

2012-12-31

Research done in this study showed that P-SV seismic data provide better spatial resolution of geologic targets at our Appalachian Basin study area than do P-P data. This finding is important because the latter data (P-P) are the principal seismic data used to evaluate rock systems considered for CO{sub 2} sequestration. The increase in P-SV{sub 1} resolution over P-P resolution was particularly significant, with P-SV{sub 1} wavelengths being approximately 40-percent shorter than P-P wavelengths. CO{sub 2} sequestration projects across the Appalachian Basin should take advantage of the increased resolution provided by converted-shear seismic modes relative to P-wave seismic data. In addition to S-wave data providing better resolution of geologic targets, we found S-wave images described reservoir heterogeneities that P-P data could not see. Specifically, a channel-like anomaly was imaged in a key porous sandstone interval by P-SV{sub 1} data, and no indication of the feature existed in P-P data. If any stratigraphic unit is considered for CO{sub 2} storage purposes, it is important to know all heterogeneities internal to the unit to understand reservoir compartmentalization. We conclude it is essential that multicomponent seismic data be used to evaluate all potential reservoir targets whenever a CO{sub 2} storage effort is considered, particularly when sequestration efforts are initiated in the Appalachian Basin. Significant differences were observed between P-wave sequences and S- wave sequences in data windows corresponding to the Oriskany Sandstone, a popular unit considered for CO{sub 2} sequestration. This example demonstrates that S-wave sequences and facies often differ from P-wave sequences and facies and is a principle we have observed in every multicomponent seismic interpretation our research laboratory has done. As a result, we now emphasis elastic wavefield seismic stratigraphy in our reservoir characterization studies, which is a science based on the

A Dynamic Programming Model for Optimizing Frequency of Time-Lapse Seismic Monitoring in Geological CO2 Storage

Science.gov (United States)

Bhattacharjya, D.; Mukerji, T.; Mascarenhas, O.; Weyant, J.

2005-12-01

Designing a cost-effective and reliable monitoring program is crucial to the success of any geological CO2 storage project. Effective design entails determining both, the optimal measurement modality, as well as the frequency of monitoring the site. Time-lapse seismic provides the best spatial coverage and resolution for reservoir monitoring. Initial results from Sleipner (Norway) have demonstrated effective monitoring of CO2 plume movement. However, time-lapse seismic is an expensive monitoring technique especially over the long term life of a storage project and should be used judiciously. We present a mathematical model based on dynamic programming that can be used to estimate site-specific optimal frequency of time-lapse surveys. The dynamics of the CO2 sequestration process are simplified and modeled as a four state Markov process with transition probabilities. The states are M: injected CO2 safely migrating within the target zone; L: leakage from the target zone to the adjacent geosphere; R: safe migration after recovery from leakage state; and S: seepage from geosphere to the biosphere. The states are observed only when a monitoring survey is performed. We assume that the system may go to state S only from state L. We also assume that once observed to be in state L, remedial measures are always taken to bring it back to state R. Remediation benefits are captured by calculating the expected penalty if CO2 seeped into the biosphere. There is a trade-off between the conflicting objectives of minimum discounted costs of performing the next time-lapse survey and minimum risk of seepage and its associated costly consequences. A survey performed earlier would spot the leakage earlier. Remediation methods would have been utilized earlier, resulting in savings in costs attributed to excessive seepage. On the other hand, there are also costs for the survey and remedial measures. The problem is solved numerically using Bellman's optimality principal of dynamic

On determining fluxgate magnetometer spin axis offsets from mirror mode observations

Science.gov (United States)

Plaschke, Ferdinand; Narita, Yasuhito

2016-09-01

In-flight calibration of fluxgate magnetometers that are mounted on spacecraft involves finding their outputs in vanishing ambient fields, the so-called magnetometer offsets. If the spacecraft is spin-stabilized, then the spin plane components of these offsets can be relatively easily determined, as they modify the spin tone content in the de-spun magnetic field data. The spin axis offset, however, is more difficult to determine. Therefore, usually Alfvénic fluctuations in the solar wind are used. We propose a novel method to determine the spin axis offset: the mirror mode method. The method is based on the assumption that mirror mode fluctuations are nearly compressible such that the maximum variance direction is aligned to the mean magnetic field. Mirror mode fluctuations are typically found in the Earth's magnetosheath region. We introduce the method and provide a first estimate of its accuracy based on magnetosheath observations by the THEMIS-C spacecraft. We find that 20 h of magnetosheath measurements may already be sufficient to obtain high-accuracy spin axis offsets with uncertainties on the order of a few tenths of a nanotesla, if offset stability can be assumed.

On determining fluxgate magnetometer spin axis offsets from mirror mode observations

Directory of Open Access Journals (Sweden)

F. Plaschke

2016-09-01

Full Text Available In-flight calibration of fluxgate magnetometers that are mounted on spacecraft involves finding their outputs in vanishing ambient fields, the so-called magnetometer offsets. If the spacecraft is spin-stabilized, then the spin plane components of these offsets can be relatively easily determined, as they modify the spin tone content in the de-spun magnetic field data. The spin axis offset, however, is more difficult to determine. Therefore, usually Alfvénic fluctuations in the solar wind are used. We propose a novel method to determine the spin axis offset: the mirror mode method. The method is based on the assumption that mirror mode fluctuations are nearly compressible such that the maximum variance direction is aligned to the mean magnetic field. Mirror mode fluctuations are typically found in the Earth's magnetosheath region. We introduce the method and provide a first estimate of its accuracy based on magnetosheath observations by the THEMIS-C spacecraft. We find that 20 h of magnetosheath measurements may already be sufficient to obtain high-accuracy spin axis offsets with uncertainties on the order of a few tenths of a nanotesla, if offset stability can be assumed.

Relays undergo seismic tests

International Nuclear Information System (INIS)

Burton, J.C.

1977-01-01

Utilities are required by the Nuclear Regulatory Commission to document that seismic vibration will not adversely affect critical electrical equipment. Seismic testing should be designed to determine the malfunction level (fragility testing). Input possibilities include a continuous sine, a decaying sine, a sine beat, random vibrations, and combinations of random vibrations and sine beat. The sine beat most accurately simulates a seismic event. Test frequencies have a broad range in order to accommodate a variety of relay types and cabinet mounting. Simulation of motion along three axes offers several options, but is best achieved by three in-phase single-axis vibration machines that are less likely to induce testing fatigue failure. Consensus on what constitutes relay failure favors a maximum two microsecond discontinuity. Performance tests should be conducted for at least two of the following: (1) nonoperating modes, (2) operating modes, or (3) the transition above the two modes, with the monitoring mode documented for all three. Results should specify a capability curve of maximum safe seismic acceleration and a graph plotting acceleration with sine-beat frequency

Reservoir characterization using production data and time-lapse seismic data

Energy Technology Data Exchange (ETDEWEB)

Dadashpour, Mohsen

2009-12-15

horizontal direction, and give a significant image of fluid and pressure changes from the entire reservoir. However, the results are associated with errors and uncertainties that are related to the repeatability of data acquisition, data processing sequences, low resolution in vertical direction, lack of rock physics understanding, and an error in up-scaling and cross-scaling seismic and simulation data. This project uses exact amplitudes related to the seismic images after processing them in two different forms: Zero offset amplitudes and Amplitude versus offset (AVO) gradients. The effect of adding AVO gradients in the objective function (the misfit between responses of model and real reservoir) is discussed. One of the key issues in parameter estimation is to develop an efficient and reliable non-linear regression procedure. This procedure is based on three concepts: mathematical model, objective function and optimization algorithm. The mathematical model (Forward model) in this project consists of two parts: a Reservoir simulator and a Forward seismic model. A three phase black oil commercial simulator (ECLIPSE 100) is used to simulate fluid and pressure changes within the reservoir due to depletion and water injection. Forward seismic modeling software, based on rock physic formulations (Gassmann equation and Hertz-Mindlin model) and matrix propagating techniques developed at NTNU, is used to provide 4D seismic amplitudes from saturation and pressure changes. A new objective function which is defined as the difference between observation data and simulated data contains 4D seismic and production parts. Because these data are from different natures, integrating them still present a challenge. A key issue is the type of 4D seismic data and the weighting factor between these terms. Different scenarios and weighting factors are tested and discussed. Different optimization techniques are tested to choose the easiest, fastest and most efficient and robust optimization

Evidence of Apulian crustal structures related to low energy seismicity (Murge, Southern Italy)

Energy Technology Data Exchange (ETDEWEB)

Del Gaudio, V.; Ripa, R. R.; Iurilli, V.; Moretti, M.; Pieri, P. [Bari Univ., Bari (Italy). Dipt. di Geologia e Geofisica; Festa, V. [Bari Univ., Bari (Italy). Dipt. Geomineralogico; Pierri, P. [Bari Univ., Bari (Italy). Osservatorio Sismologico; Calcagnile, G. [Bari Univ., Bari (Italy). Dipt. di Geologia e Geofisica; Bari Univ., Bari (Italy). Osservatorio Sismologico; Tropeano, M [Potenza Universita' della Basilicata, Potenza (Italy). Dipt. di Scienze Geologiche

2001-12-01

The discovery of recent co-seismic sedimentary structures and the detection of low energy seismic activity in the Murgian plateau (Apulia, Southern Italy) motivated a more detailed examination of the tectonics in this part of the Apulian plate commonly believed to be aseismic. In particular, it was examined the north-western zone where a seismic sequence with maximum magnitude 3.2 and tensional focal mechanism occurred in 1991. The analysis of the existing gravimetric data, integrated by three new profiles carried out across the epicentral area, disclosed an anomaly possibly due to an old tensional tectonic structure located within the upper crust. Even though the depth and the age hypothesised for the anomaly source would exclude a direct causal connection with the observed seismicity, this structure could be a shallower expression of a tectonic structure extending down to the crystalline basement: it could represent a zone of relative weakness where the regional stress, due to the interactions between Apennines and Apulian plate, encounters conditions facilitating the release of seismic energy.

Handbook of Carbon Offset Programs. Trading Systems, Funds, Protocols and Standards

Energy Technology Data Exchange (ETDEWEB)

Kollmuss, Anja; Lazarus, Michael; Lee, Carrie; Polycarp, Clifford (SEI-US (United States)); LeFranc, Maurice (US EPA (United States))

2010-03-15

Greenhouse gas (GHG) offsets have long been promoted as an important element of a comprehensive climate policy approach. Offset programs can reduce the overall cost of achieving a given emission goal by enabling emission reductions to occur where costs are lower. Offsets have the potential to deliver sustainability co-benefits, through technology development and transfer. They can also develop human and institutional capacity for reducing emissions in sectors and locations not included in a cap and trade or a mandatory government policy. However, offsets can pose a risk to the environmental integrity of climate actions, especially if issues surrounding additionality, permanence, leakage, quantification and verification are not adequately addressed. The challenge is to design offset programs and policies that can maximize their potential benefits while minimizing their potential risks. This handbook provides a systematic and comprehensive review of existing offset programs. It looks are what offsets are, how offset mechanisms function, and the successes and pitfalls they have encountered. Coverage includes offset programs across the full swath of applications including mandatory and voluntary systems, government regulated and private markets, carbon offset funds, and accounting and reporting protocols such as the WBCSD/WRI GHG Protocol and ISO 14064. Learning from the successes and failures of these programs will be essential to crafting effective climate policy. A reference for regulators, policy makers, business leaders and NGOs concerned with the design and operation of GHG offset programs world-wide

Remaining gaps for "safe" CO2 storage: the INGV CO2GAPS vision of "learning by doing" monitoring geogas leakage, reservoirs contamination/mixing and induced/triggered seismicity

Science.gov (United States)

Quattrocchi, F.; Vinciguerra, S.; Chiarabba, C.; Boschi, E.; Anselmi, M.; Burrato, P.; Buttinelli, M.; Cantucci, B.; Cinti, D.; Galli, G.; Improta, L.; Nazzari, M.; Pischiutta, M.; Pizzino, L.; Procesi, M.; Rovelli, A.; Sciarra, A.; Voltattorni, N.

2012-12-01

The CO2GAPS project proposed by INGV is intended to build up an European Proposal for a new kind of research strategy in the field of the geogas storage. Aim of the project would be to fill such key GAPS concerning the main risks associated to CO2 storage and their implications on the entire Carbon Capture and Storage (CCS) process, which are: i) the geogas leakage both in soils and shallow aquifers, up to indoor seepage; ii) the reservoirs contamination/mixing by hydrocarbons and heavy metals; iii) induced or triggered seismicity and microseismicity, especially for seismogenic blind faults. In order to consider such risks and make the CCS public acceptance easier, a new kind of research approach should be performed by: i) a better multi-disciplinary and "site specific" risk assessment; ii) the development of more reliable multi-disciplinary monitoring protocols. In this view robust pre-injection base-lines (seismicity and degassing) as well as identification and discrimination criteria for potential anomalies are mandatory. CO2 injection dynamic modelling presently not consider reservoirs geomechanical properties during reactive mass-transport large scale simulations. Complex simulations of the contemporaneous physic-chemical processes involving CO2-rich plumes which move, react and help to crack the reservoir rocks are not totally performed. These activities should not be accomplished only by the oil-gas/electric companies, since the experienced know-how should be shared among the CCS industrial operators and research institutions, with the governments support and overview, also flanked by a transparent and "peer reviewed" scientific popularization process. In this context, a preliminary and reliable 3D modelling of the entire "storage complex" as defined by the European Directive 31/2009 is strictly necessary, taking into account the above mentioned geological, geochemical and geophysical risks. New scientific results could also highlighting such opportunities

Four years of experience with a permanent seismic monitoring array at the Ketzin CO2 storage pilot site

NARCIS (Netherlands)

Paap, B.F.; Verdel, A.R.; Meekes, J.A.C.; Steeghs, T.P.H.; Vandeweijer, V.P.; Neele, F.P.

2014-01-01

CO2 was injected into a saline aquifer near the town of Ketzin in Germany from July 2008 to August 2013. To monitor CO2- migration close to the injection well, TNO installed a fixed 2D seismic array of 120 meters length in 2009, with 3- component (3- C) geophones at the surface, 4-component

A multimethod Global Sensitivity Analysis to aid the calibration of geomechanical models via time-lapse seismic data

Science.gov (United States)

Price, D. C.; Angus, D. A.; Garcia, A.; Fisher, Q. J.; Parsons, S.; Kato, J.

2018-03-01

Time-lapse seismic attributes are used extensively in the history matching of production simulator models. However, although proven to contain information regarding production induced stress change, it is typically only loosely (i.e. qualitatively) used to calibrate geomechanical models. In this study we conduct a multimethod Global Sensitivity Analysis (GSA) to assess the feasibility and aid the quantitative calibration of geomechanical models via near-offset time-lapse seismic data. Specifically, the calibration of mechanical properties of the overburden. Via the GSA, we analyse the near-offset overburden seismic traveltimes from over 4000 perturbations of a Finite Element (FE) geomechanical model of a typical High Pressure High Temperature (HPHT) reservoir in the North Sea. We find that, out of an initially large set of material properties, the near-offset overburden traveltimes are primarily affected by Young's modulus and the effective stress (i.e. Biot) coefficient. The unexpected significance of the Biot coefficient highlights the importance of modelling fluid flow and pore pressure outside of the reservoir. The FE model is complex and highly nonlinear. Multiple combinations of model parameters can yield equally possible model realizations. Consequently, numerical calibration via a large number of random model perturbations is unfeasible. However, the significant differences in traveltime results suggest that more sophisticated calibration methods could potentially be feasible for finding numerous suitable solutions. The results of the time-varying GSA demonstrate how acquiring multiple vintages of time-lapse seismic data can be advantageous. However, they also suggest that significant overburden near-offset seismic time-shifts, useful for model calibration, may take up to 3 yrs after the start of production to manifest. Due to the nonlinearity of the model behaviour, similar uncertainty in the reservoir mechanical properties appears to influence overburden

Structure of pseudotachylyte vein systems as a key to co-seismic rupture dynamics: the case of Gavilgarh-Tan Shear Zone, central India

Science.gov (United States)

Chattopadhyay, A.; Bhattacharjee, D.; Mukherjee, S.

2014-04-01

The secondary fractures associated with a major pseudotachylyte-bearing fault vein in the sheared aplitic granitoid of the Proterozoic Gavilgarh-Tan Shear Zone in central India are mapped at the outcrop scale. The fracture maps help to identify at least three different types of co-seismic ruptures, e.g., X-X', T1 and T2, which characterize sinistral-sense shearing of rocks, confined between two sinistral strike-slip faults slipping at seismic rate. From the asymmetric distribution of tensile fractures around the sinistral-sense fault vein, the direction of seismic rupture propagation is predicted to have occurred from west-southwest to east-northeast, during an ancient (Ordovician?) earthquake. Calculations of approximate co-seismic displacement on the faults and seismic moment ( M 0) of the earthquake are attempted, following the methods proposed by earlier workers. These estimates broadly agree to the findings from other studied fault zones (e.g., Gole Larghe Fault zone, Italian Alps). This study supports the proposition by some researchers that important seismological information can be extracted from tectonic pseudotachylytes of all ages, provided they are not reworked by subsequent tectonic activity.

Understanding Seismic Anisotropy in Hunt Well of Fort McMurray, Canada

Science.gov (United States)

Malehmir, R.; Schmitt, D. R.; Chan, J.

2014-12-01

Seismic imaging plays vital role in geothermal systems as a sustainable energy resource. In this paper, we acquired and processed zero-offset and walk-away VSP and logging as well as surface seismic in Athabasca oil sand area, Alberta. Seismic data were highly processed to make better image geothermal system. Through data processing, properties of natural fractures such as orientation and width were studied and high probable permeable zones were mapped along the deep drilled to the depth of 2363m deep into crystalline basement rocks. In addition to logging data, seismic data were processed to build a reliable image of underground. Velocity analysis in high resolution multi-component walk-away VSP informed us about the elastic anisotropy in place. Study of the natural and induced fracture as well as elastic anisotropy in the seismic data, led us to better map stress regime around the well bore. The seismic image and map of fractures optimizes enhanced geothermal stages through hydraulic stimulation. Keywords: geothermal, anisotropy, VSP, logging, Hunt well, seismic

Evidence of shallow gas in the Queen Charlotte Basin from waveform tomography of seismic reflection data

Energy Technology Data Exchange (ETDEWEB)

Takam Takougang, Eric M.; Calvert, Andrew J. [Simon Fraser University (Canada)], email: eta9@sfu.ca

2011-07-01

The Geological Survey of Canada (GSC) collected eight seismic reflection lines in 1988 across the Queen Charlotte sedimentary basin of western Canada, which is the largest tertiary basin on the west coast. This work furthers the study of the upper part of the basin by using quantitative imaging of its structure through application of 2-D waveform tomography to the limited offset seismic reflection data. With the help of waveform tomography, seismic reflection data has allowed the identification of pockmark structures and pipe-like gas chimney in the recovered velocity and attenuation models. Overall, there is an excellent match between field data and predicted data. and a good match between the sonic log and a 1-D velocity function derived from the 2-D velocity model. This shows that specific preconditioning of the data and a good inversion strategy make it possible to use waveform tomography of relatively short offset reflection data for the imaging of shallow geological features.

Willingness to Pay of Air Passengers for Carbon-Offset

Directory of Open Access Journals (Sweden)

Rong-Chang Jou

2015-03-01

Full Text Available An important source of anthropogenic greenhouse gas (GHG emissions is the air transport sector, which accounts for approximately 2% of global GHG emissions. Therefore, reducing GHG emissions from aircrafts has become a major challenge for transportation authorities worldwide. In recent years, much research has focused on tax ideas related to the CO2 emissions produced by air transport, such as the voluntary carbon offset (VCO. This study investigates the willingness of economy class air passengers to pay to compensate for the CO2 emissions produced during their journeys from Taiwan to Hong Kong. Together with the Spike model, a framework known as the contingent valuation (CV method offers a way to investigate how much the air passenger would be willing to pay to offset a journey’s airplane-generated CO2 emissions. The Spike model was applied to address the problem of zero willingness to pay (WTP. The results obtained in this study are consistent with the results found in previous studies and therefore can provide valuable insights into pricing strategies for airlines.

Offset drilling obligations

International Nuclear Information System (INIS)

Boyd, K.D.; Kalmakoff, J.J.

1998-01-01

A review of the 'offset well' clause found in freehold and Crown natural gas and petroleum leases was presented. The objective was to provide lessors and lessees with a clear understanding of the rights and obligations associated with offset wells. It was noted that offset well obligations vary according to the form of lease used, the type of offsetting well, the regulatory regime and the geophysical characteristics of the producing formation. Some suggestions were made as to how current versions of the offset well clause can be amended to overcome some of the problems encountered in applying the clause to an offset horizontal well that has been drilled on adjoining lands. Failure to resolve the new issues presented by horizontal drilling technology in terms of documentation, which records respective rights and obligations on the basis of generally accepted principles, will result in large numbers of conflicts and unnecessary litigation. 144 refs., 1 fig

Environmental impact of CO2, Rn, Hg degassing from the rupture zones produced by Wenchuan M s 8.0 earthquake in western Sichuan, China.

Science.gov (United States)

Zhou, Xiaocheng; Chen, Zhi; Cui, Yueju

2016-10-01

The concentrations and flux of CO2, (222)Radon (Rn), and gaseous elemental mercury (Hg) in soil gas were investigated based on the field measurements in June 2010 at ten sites along the seismic rupture zones produced by the May 12, 2008, Wenchuan M s 8.0 earthquake in order to assess the environmental impact of degassing of CO2, Rn and Hg. Soil gas concentrations of 344 sampling points were obtained. Seventy measurements of CO2, Rn and Hg flux by the static accumulation chamber method were performed. The results of risk assessment of CO2, Rn and Hg concentration in soil gas showed that (1) the concentration of CO2 in the epicenter of Wenchuan M s 8.0 earthquake and north end of seismic ruptures had low risk of asphyxia; (2) the concentrations of Rn in the north segment of seismic ruptures had high levels of radon, Maximum was up to level 4, according to Chinese code (GB 50325-2001); (3) the average geoaccumulation index I geo of soil Hg denoted the lack of soil contamination, and maximum values classified the soil gas as moderately to strongly polluted in the epicenter. The investigation of soil gas CO2, Rn and Hg degassing rate indicated that (1) the CO2 in soil gas was characterized by a mean [Formula: see text] of -20.4 ‰ and by a mean CO2 flux of 88.1 g m(-2) day(-1), which were in the range of the typical values for biologic CO2 degassing. The maximum of soil CO2 flux reached values of 399 g m(-2) day(-1) in the epicenter; (2) the soil Rn had higher exhalation in the north segment of seismic ruptures, the maximum reached value of 1976 m Bq m(-2) s(-1); (3) the soil Hg flux was lower, ranging from -2.5 to 18.7 n g m(-2) h(-1) and increased from south to north. The mean flux over the all profiles was 4.2 n g m(-2) h(-1). The total output of CO2 and Hg degassing estimated along seismic ruptures for a survey area of 18.17 km(2) were approximately 0.57 Mt year(-1) and 688.19 g year(-1). It is recommended that land-use planners should

Seismic reflections associated with submarine gas hydrates

Energy Technology Data Exchange (ETDEWEB)

Andreassen, K

1996-12-31

Gas hydrates are often suggested as a future energy resource. This doctoral thesis improves the understanding of the concentration and distribution of natural submarine gas hydrates. The presence of these hydrates are commonly inferred from strong bottom simulating reflection (BSR). To investigate the nature of BSR, this work uses seismic studies of hydrate-related BSRs at two different locations, one where gas hydrates are accepted to exist and interpreted to be very extensive (in the Beaufort Sea), the other with good velocity data and downhole logs available (offshore Oregon). To ascertain the presence of free gas under the BSR, prestack offset data must supplement near-vertical incidence seismic data. A tentative model for physical properties of sediments partially saturated with gas hydrate and free gas is presented. This model, together with drilling information and seismic data containing the BSR beneath the Oregon margin and the Beaufort Sea, made it possible to better understand when to apply the amplitude-versus-offset (AVO) method to constrain BSR gas hydrate and gas models. Distribution of natural gas hydrates offshore Norway and Svalbard is discussed and interpreted as reflections from the base of gas hydrate-bearing sediments, overlying sediments containing free gas. Gas hydrates inferred to exist at the Norwegian-Svalbard continental margin correlate well with Cenozoic depocenters, and the associated gas is assumed to be mainly biogenic. Parts of that margin have a high potential for natural gas hydrates of both biogenic and thermogenic origin. 235 refs., 86 figs., 4 tabs.

Seismic reflections associated with submarine gas hydrates

Energy Technology Data Exchange (ETDEWEB)

Andreassen, K.

1995-12-31

Gas hydrates are often suggested as a future energy resource. This doctoral thesis improves the understanding of the concentration and distribution of natural submarine gas hydrates. The presence of these hydrates are commonly inferred from strong bottom simulating reflection (BSR). To investigate the nature of BSR, this work uses seismic studies of hydrate-related BSRs at two different locations, one where gas hydrates are accepted to exist and interpreted to be very extensive (in the Beaufort Sea), the other with good velocity data and downhole logs available (offshore Oregon). To ascertain the presence of free gas under the BSR, prestack offset data must supplement near-vertical incidence seismic data. A tentative model for physical properties of sediments partially saturated with gas hydrate and free gas is presented. This model, together with drilling information and seismic data containing the BSR beneath the Oregon margin and the Beaufort Sea, made it possible to better understand when to apply the amplitude-versus-offset (AVO) method to constrain BSR gas hydrate and gas models. Distribution of natural gas hydrates offshore Norway and Svalbard is discussed and interpreted as reflections from the base of gas hydrate-bearing sediments, overlying sediments containing free gas. Gas hydrates inferred to exist at the Norwegian-Svalbard continental margin correlate well with Cenozoic depocenters, and the associated gas is assumed to be mainly biogenic. Parts of that margin have a high potential for natural gas hydrates of both biogenic and thermogenic origin. 235 refs., 86 figs., 4 tabs.

Estimation of pore pressure from seismic velocities

International Nuclear Information System (INIS)

Perez, Zayra; Ojeda, German Y; Mateus, Darwin

2009-01-01

On pore pressure calculations it is common to obtain a profile in a well bore, which is then extrapolated toward offset wells. This practice might generate mistakes on pore pressure measurements, since geological conditions may change from a well bore to another, even into the same basin. Therefore, it is important to use other tools which allow engineers not only to detect and estimate in an indirect way overpressure zones, but also to keep a lateral tracking of possible changes that may affect those values in the different formations. Taking into account this situation, we applied a methodology that estimates formation pressure from 3D seismic velocities by using the Eaton method. First, we estimated formation pore pressure; then, we identified possible overpressure zones. Finally, those results obtained from seismic information were analyzed involving well logs and pore pressure tests, in order to compare real data with prediction based on seismic information from the Colombian foothill.

Seismic source characterisation of a Tunnel Boring Machine (TBM)

Science.gov (United States)

Kreutzer, Ingrid; Brückl, Ewald; Radinger, Alexander

2015-04-01

The Tunnel Seismic While Drilling (TSWD) method aims at predicting continuously the geological situation ahead of the tunnel without disturbing the construction work. Thereby the Tunnel Boring Machine (TBM) itself is used as seismic source. The cutting process generates seismic waves radiating into the rock mass and vibrations propagating to the main bearing of the cutter head. These vibrations are monitored and used as pilot signal. For the processing and interpretation it was hypothesized so far that the TBM acts like a single force. To prove this assumption the radiation pattern of several TBM's under construction were investigated. Therefore 3-components geophones were installed at the surface, which were situated directly above the tunnel axes and also with lateral offset. Additional, borehole geophones were placed in the wall of one tube of a two-tube tunnel. The geophones collected the forward and backward radiated wave field, as the TBM, operating in the other tube, passed their positions. The obtained seismic data contains continuous records over a range of 600 m of the TBM position. The offsets vary from 25 m to 400 m and the frequency ranges from 20-250 Hertz. The polarisation of the p-wave and the s-wave and their amplitude ratio were determined and compared with modelled seismograms with different source mechanism. The results show that the description of the source mechanism by a single force can be used as a first order approximation. More complex radiation pattern including tensile forces and several source locations like the transmission of reaction forces over the gripper to the tunnel wall are further tested and addressed.

Variability of medial and posterior offset in patients with fourth-generation stemmed shoulder arthroplasty.

Science.gov (United States)

Irlenbusch, Ulrich; Berth, Alexander; Blatter, Georges; Zenz, Peter

2012-03-01

Most anthropometric data on the proximal humerus has been obtained from deceased healthy individuals with no deformities. Endoprostheses are implanted for primary and secondary osteoarthritis, rheumatoid arthritis,humeral-head necrosis, fracture sequelae and other humeral-head deformities. This indicates that pathologicoanatomical variability may be greater than previously assumed. We therefore investigated a group of patients with typical shoulder replacement diagnoses, including posttraumatic and rheumatic deformities. One hundred and twenty-two patients with a double eccentrically adjustable shaft endoprosthesis served as a specific dimension gauge to determine in vivo the individual humeral-head rotation centres from the position of the adjustable prosthesis taper and the eccentric head. All prosthesis heads were positioned eccentrically.The entire adjustment range of the prosthesis of 12 mm medial/lateral and 6 mm dorsal/ventral was required. Mean values for effective offset were 5.84 mm mediolaterally[standard deviation (SD) 1.95, minimum +2, maximum +11]and 1.71 mm anteroposteriorly (SD 1.71, minimum −3,maximum 3 mm), averaging 5.16 mm (SD 1.76, minimum +2,maximum + 10). The posterior offset averaged 1.85 mm(SD 1.85, minimum −1, maximum + 6 mm). In summary, variability of the combined medial and dorsal offset of the humeral-head rotational centre determined in patients with typical underlying diagnoses in shoulder replacement was not greater than that recorded in the literature for healthy deceased patients.The range of deviation is substantial and shows the need for an adjustable prosthetic system.

Methodology to evaluate the site standard seismic motion to a nuclear facility

International Nuclear Information System (INIS)

Soares, W.A.

1983-01-01

For the seismic design of nuclear facilities, the input motion is normally defined by the predicted maximum ground horizontal acceleration and the free field ground response spectrum. This spectrum is computed on the basis of records of strong motion earthquakes. The pair maximum acceleration-response spectrum is called the site standard seismic motion. An overall view of the subjects involved in the determination of the site standard seismic motion to a nuclear facility is presented. The main topics discussed are: basic principles of seismic instrumentation; dynamic and spectral concepts; design earthquakes definitions; fundamentals of seismology; empirical curves developed from prior seismic data; available methodologies and recommended procedures to evaluate the site standard seismic motion. (Author) [pt

Slip-accumulation patterns and earthquake recurrences along the Talas-Fergana Fault - Contributions of high-resolution geomorphic offsets.

Science.gov (United States)

Rizza, M.; Dubois, C.; Fleury, J.; Abdrakhmatov, K.; Pousse, L.; Baikulov, S.; Vezinet, A.

2017-12-01

In the western Tien-Shan Range, the largest intracontinental strike-slip fault is the Karatau-Talas Fergana Fault system. This dextral fault system is subdivided into two main segments: the Karatau fault to the north and the Talas-Fergana fault (TFF) to the south. Kinematics and rates of deformation for the TFF during the Quaternary period are still debated and are poorly constrained. Only a few paleoseismological investigations are availabe along the TFF (Burtman et al., 1996; Korjenkov et al., 2010) and no systematic quantifications of the dextral displacements along the TFF has been undertaken. As such, the appraisal of the TFF behavior demands new tectonic information. In this study, we present the first detailed analysis of the morphology and the segmentation of the TFF and an offset inventory of morphological markers along the TFF. To discuss temporal and spatial recurrence patterns of slip accumulated over multiple seismic events, our study focused on a 60 km-long section of the TFF (Chatkal segment). Using tri-stereo Pleiades satellite images, high-resolution DEMs (1*1 m pixel size) have been generated in order to (i) analyze the fine-scale fault geometry and (ii) thoroughly measure geomorphic offsets. Photogrammetry data obtained from our drone survey on high interest sites, provide higher-resolution DEMs of 0.5 * 0.5 m pixel size.Our remote sensing mapping allows an unprecedented subdivision - into five distinct segments - of the study area. About 215 geomorphic markers have been measured and offsets range from 4.5m to 180 m. More than 80% of these offsets are smaller than 60 m, suggesting landscape reset during glacial maximum. Calculations of Cumulative Offset Probability Density (COPD) for the whole 60 km-long section as well as for each segments support distinct behavior from a segment to another and thus variability in slip-accumulation patterns. Our data argue for uniform slip model behavior along this section of the TFF. Moreover, we excavated a

Geomechanical Modeling for Improved CO2 Storage Security

Science.gov (United States)

Rutqvist, J.; Rinaldi, A. P.; Cappa, F.; Jeanne, P.; Mazzoldi, A.; Urpi, L.; Vilarrasa, V.; Guglielmi, Y.

2017-12-01

This presentation summarizes recent modeling studies on geomechanical aspects related to Geologic Carbon Sequestration (GCS,) including modeling potential fault reactivation, seismicity and CO2 leakage. The model simulations demonstrates that the potential for fault reactivation and the resulting seismic magnitude as well as the potential for creating a leakage path through overburden sealing layers (caprock) depends on a number of parameters such as fault orientation, stress field, and rock properties. The model simulations further demonstrate that seismic events large enough to be felt by humans requires brittle fault properties as well as continuous fault permeability allowing for the pressure to be distributed over a large fault patch to be ruptured at once. Heterogeneous fault properties, which are commonly encountered in faults intersecting multilayered shale/sandstone sequences, effectively reduce the likelihood of inducing felt seismicity and also effectively impede upward CO2 leakage. Site specific model simulations of the In Salah CO2 storage site showed that deep fractured zone responses and associated seismicity occurred in the brittle fractured sandstone reservoir, but at a very substantial reservoir overpressure close to the magnitude of the least principal stress. It is suggested that coupled geomechanical modeling be used to guide the site selection and assisting in identification of locations most prone to unwanted and damaging geomechanical changes, and to evaluate potential consequence of such unwanted geomechanical changes. The geomechanical modeling can be used to better estimate the maximum sustainable injection rate or reservoir pressure and thereby provide for improved CO2 storage security. Whether damaging geomechanical changes could actually occur very much depends on the local stress field and local reservoir properties such the presence of ductile rock and faults (which can aseismically accommodate for the stress and strain induced by

Determination of a natural valence-band offset - The case of HgTe and CdTe

Science.gov (United States)

Shih, C. K.; Spicer, W. E.

1987-01-01

A method to determine a natural valence-band offset (NVBO), i.e., the change in the valence-band maximum energy which is intrinsic to the bulk band structures of semiconductors is proposed. The HgTe-CdTe system is used as an example in which it is found that the valence-band maximum of HgTe lies 0.35 + or - 0.06 eV above that of CdTe. The NVBO of 0.35 eV is in good agreement with the X-ray photoemission spectroscopy measurement of the heterojunction offset. The procedure to determine the NVBO between semiconductors, and its implication on the heterojunction band lineup and the electronic structures of semiconductor alloys, are discussed.

Active intra-basin faulting in the Northern Basin of Lake Malawi from seismic reflection data

Science.gov (United States)

Shillington, D. J.; Chindandali, P. R. N.; Scholz, C. A.; Ebinger, C. J.; Onyango, E. A.; Peterson, K.; Gaherty, J. B.; Nyblade, A.; Accardo, N. J.; McCartney, T.; Oliva, S. J.; Kamihanda, G.; Ferdinand, R.; Salima, J.; Mruma, A. H.

2016-12-01

Many questions remain about the development and evolution of fault systems in weakly extended rifts, including the relative roles of border faults and intra-basin faults, and segmentation at various scales. The northern Lake Malawi (Nyasa) rift in the East African Rift System is an early stage rift exhibiting pronounced tectonic segmentation, which is defined by 100-km-long border faults. The basins also contain a series of intrabasinal faults and associated synrift sediments. The occurrence of the 2009 Karonga Earthquake Sequence on one of these intrabasinal faults indicates that some of them are active. Here we present new multichannel seismic reflection data from the Northern Basin of the Malawi Rift collected in 2015 as a part of the SEGMeNT (Study of Extension and maGmatism in Malawi aNd Tanzania) project. This rift basin is bound on its east side by the west-dipping Livingstone border fault. Over 650 km of seismic reflection profiles were acquired in the Northern Basin using a 500 to 1540 cu in air gun array and a 1200- to 1500-m seismic streamer. Dip lines image a series of north-south oriented west-dipping intra-basin faults and basement reflections up to 5 s twtt near the border fault. Cumulative offsets on intra-basin faults decrease to the west. The largest intra-basin fault has a vertical displacement of >2 s two-way travel time, indicating that it has accommodated significant total extension. Some of these intra-basin faults offset the lake bottom and the youngest sediments by up to 50 s twtt ( 37 m), demonstrating they are still active. The two largest intra-basin faults exhibit the largest offsets of young sediments and also correspond to the area of highest seismicity based on analysis of seismic data from the 89-station SEGMeNT onshore/offshore network (see Peterson et al, this session). Fault patterns in MCS profiles vary along the basin, suggesting a smaller scale of segmentation of faults within the basin; these variations in fault patterns

Experimental seismic test of fluid coupled co-axial cylinders

International Nuclear Information System (INIS)

Chu, M.L.; Brown, S.J.; Lestingi, J.F.

1979-01-01

The dynamic response of fluid coupled coaxial cylindrical shells is of interest to the nuclear industry with respect to the seismic design of the reactor vessel and thermal liner. The experiments described present a series of tests which investigate the effect of the annular clearance between the cylinders (gap) on natural frequency, damping, and seismic response of both the inner and outer cylinders. The seismic input is a time history base load to the flexible fluid filled coaxial cylinders. The outer cylinder is elastically supported at both ends while the inner cylinder is supported only at the base (lower) end

New seismic source `BLASTER` for seismic survey; Hasaiyaku wo shingen to shite mochiita danseiha tansa

Energy Technology Data Exchange (ETDEWEB)

Koike, G; Yoshikuni, Y [OYO Corp., Tokyo (Japan)

1996-10-01

Built-up weight and vacuole have been conceived as seismic sources without using explosive. There have been problems that they have smaller energy to generate elastic wave than explosive, and that they have inferior working performance. Concrete crushing explosive is tried to use as a new seismic source. It is considered to possess rather large seismic generating energy, and it is easy to handle from the viewpoint of safety. Performance as seismic source and applicability to exploration works of this crushing explosive were compared with four kinds of seismic sources using dynamite, dropping weight, shot-pipe utilizing shot vacuole, and impact by wooden maul. When considered by the velocity amplitude, the seismic generating energy of the crushing explosive of 120 g is about one-fifth of dynamite of 100 g. Elastic wave generated includes less high frequency component than that by dynamite, and similar to that using seismic source without explosive, such as the weight dropping. The maximum seismic receiving distance obtained by the seismic generation was about 100 m. This was effective for the slope survey with the exploration depth between 20 m and 30 m. 1 ref., 9 figs., 2 tabs.

Carbon offsetting: sustaining consumption?

OpenAIRE

Heather Lovell; Harriet Bulkeley; Diana Liverman

2009-01-01

In this paper we examine how theories of sustainable and ethical consumption help us to understand a new, rapidly expanding type of consumer product designed to mitigate climate change: carbon offsets. The voluntary carbon offset market grew by 200% between 2005 and 2006, and there are now over 150 retailers of voluntary carbon offsets worldwide. Our analysis concentrates on the production and consumption of carbon offsets, drawing on ideas from governmentality and political ecology about how...

Comparison of the Structurally Controlled Landslides Numerical Model Results to the M 7.2 2013 Bohol Earthquake Co-seismic Landslides

Science.gov (United States)

Macario Galang, Jan Albert; Narod Eco, Rodrigo; Mahar Francisco Lagmay, Alfredo

2015-04-01

The M 7.2 October 15, 2013 Bohol earthquake is the most destructive earthquake to hit the Philippines since 2012. The epicenter was located in Sagbayan municipality, central Bohol and was generated by a previously unmapped reverse fault called the "Inabanga Fault". Its name, taken after the barangay (village) where the fault is best exposed and was first seen. The earthquake resulted in 209 fatalities and over 57 billion USD worth of damages. The earthquake generated co-seismic landslides most of which were related to fault structures. Unlike rainfall induced landslides, the trigger for co-seismic landslides happen without warning. Preparedness against this type of landslide therefore, relies heavily on the identification of fracture-related unstable slopes. To mitigate the impacts of co-seismic landslide hazards, morpho-structural orientations or discontinuity sets were mapped in the field with the aid of a 2012 IFSAR Digital Terrain Model (DTM) with 5-meter pixel resolution and software was then used to identify similar structures including measurement of their dip and dip directions. The chosen discontinuity sets were then keyed into Matterocking software to identify potential rock slide zones due to planar or wedged discontinuities. After identifying the structurally-controlled unstable slopes, the rock mass propagation extent of the possible rock slides was simulated using Conefall. The results were compared to a post-earthquake landslide inventory of 456 landslides. Out the total number of landslides identified from post-earthquake high-resolution imagery, 366 or 80% intersect the structural-controlled hazard areas of Bohol. The results show the potential of this method to identify co-seismic landslide hazard areas for disaster mitigation. Along with computer methods to simulate shallow landslides, and debris flow paths, located structurally-controlled unstable zones can be used to mark unsafe areas for settlement. The method can be further improved with the

Lateral Offset Quality Rating along Low Slip Rate Faults: Application to the Alhama de Murcia Fault (SE Iberian Peninsula

Directory of Open Access Journals (Sweden)

Marta Ferrater

2015-11-01

Full Text Available Seismic hazard assessment of strike-slip faults is based partly on the identification and mapping of landforms laterally offset due to fault activity. The characterization of these features affected by slow-moving faults is challenging relative to studies emphasizing rapidly slipping faults. We propose a methodology for scoring fault offsets based on subjective and objective qualities. We apply this methodology to the Alhama de Murcia fault (SE Iberian Peninsula where we identify 138 offset features that we mapped on a high-resolution (0.5 × 0.5 m pixel size Digital Elevation Model (DEM. The amount of offset, the uncertainty of the measurement, the subjective and objective qualities, and the parameters that affect objective quality are independent variables, suggesting that our methodological scoring approach is good. Based on the offset measurements and qualifications we calculate the Cumulative Offset Probability Density (COPD for the entire fault and for each fault segment. The COPD for the segments differ from each other. Tentative interpretation of the COPDs implies that the slip rate varies from one segment to the other (we assume that channels with the same amount of offset were incised synchronously. We compare the COPD with climate proxy curves (aligning using the very limited age control to test if entrenchment events are coincident with climatic changes. Channel incision along one of the traces in Lorca-Totana segment may be related to transitions from glacial to interglacial periods.

An Ensemble Model for Co-Seismic Landslide Susceptibility Using GIS and Random Forest Method

Directory of Open Access Journals (Sweden)

Suchita Shrestha

2017-11-01

Full Text Available The Mw 7.8 Gorkha earthquake of 25 April 2015 triggered thousands of landslides in the central part of the Nepal Himalayas. The main goal of this study was to generate an ensemble-based map of co-seismic landslide susceptibility in Sindhupalchowk District using model comparison and combination strands. A total of 2194 co-seismic landslides were identified and were randomly split into 1536 (~70%, to train data for establishing the model, and the remaining 658 (~30% for the validation of the model. Frequency ratio, evidential belief function, and weight of evidence methods were applied and compared using 11 different causative factors (peak ground acceleration, epicenter proximity, fault proximity, geology, elevation, slope, plan curvature, internal relief, drainage proximity, stream power index, and topographic wetness index to prepare the landslide susceptibility map. An ensemble of random forest was then used to overcome the various prediction limitations of the individual models. The success rates and prediction capabilities were critically compared using the area under the curve (AUC of the receiver operating characteristic curve (ROC. By synthesizing the results of the various models into a single score, the ensemble model improved accuracy and provided considerably more realistic prediction capacities (91% than the frequency ratio (81.2%, evidential belief function (83.5% methods, and weight of evidence (80.1%.

Reflection imaging of the Moon's interior using deep-moonquake seismic interferometry

Science.gov (United States)

Nishitsuji, Yohei; Rowe, C. A.; Wapenaar, Kees; Draganov, Deyan

2016-04-01

The internal structure of the Moon has been investigated over many years using a variety of seismic methods, such as travel time analysis, receiver functions, and tomography. Here we propose to apply body-wave seismic interferometry to deep moonquakes in order to retrieve zero-offset reflection responses (and thus images) beneath the Apollo stations on the nearside of the Moon from virtual sources colocated with the stations. This method is called deep-moonquake seismic interferometry (DMSI). Our results show a laterally coherent acoustic boundary around 50 km depth beneath all four Apollo stations. We interpret this boundary as the lunar seismic Moho. This depth agrees with Japan Aerospace Exploration Agency's (JAXA) SELenological and Engineering Explorer (SELENE) result and previous travel time analysis at the Apollo 12/14 sites. The deeper part of the image we obtain from DMSI shows laterally incoherent structures. Such lateral inhomogeneity we interpret as representing a zone characterized by strong scattering and constant apparent seismic velocity at our resolution scale (0.2-2.0 Hz).

Vertical seismic profile data from well Mallik 2L-38 for gas hydrate studies

Energy Technology Data Exchange (ETDEWEB)

Mi, Y [Calgary Univ., AB (Canada); Walia, R [Victoria Univ., BC (Canada); Hyndman, R D; Sakai, A

1999-01-01

A gas hydrate research well was drilled in the Canadian Arctic to determine gas hydrates in a permafrost setting in a collaborative research project between the Japan National Oil Corp., and the Geological Survey of Canada with the participation of other agencies. The multidisciplinary study included an electromagnetic survey, permafrost and gas hydrate coring, and comprehensive downhole geophysical logging and measurement. Laboratory studies on recovered cores and cuttings included sedimentology, physical properties, geochemistry, and reservoir characteristics of the Mallik gas accumulation. As part of the field program, a vertical seismic profiling survey was conducted at zero and offset source positions with 3 component receiver tools and horizontal and vertical vibration sources. A special effort was made to record shear wave data, and results from this work were combined with down hole logs and regional surface seismic data. The data will be used also to determine the effect of gas hydrates on formation velocities and to measure gas hydrate concentrations as a function of depth in the formation penetrated by the well. Certain conclusions followed from the initial VSP analysis. 1) Zero offset vertical vibration Z component and horizontal X component data give reliable velocity estimation within the gas hydrate formation zone, and P wave velocities from offset data indicate excellent consistency with that from zero offset data and with the sonic log. 2) The VSP data permitted reliable identification of gas hydrate bearing zones. 4 refs.

Approximate inverse for the common offset acquisition geometry in 2D seismic imaging

Science.gov (United States)

Grathwohl, Christine; Kunstmann, Peer; Quinto, Eric Todd; Rieder, Andreas

2018-01-01

We explore how the concept of approximate inverse can be used and implemented to recover singularities in the sound speed from common offset measurements in two space dimensions. Numerical experiments demonstrate the performance of the method. We gratefully acknowledge financial support by the Deutsche Forschungsgemeinschaft (DFG) through CRC 1173. Quinto additionally thanks the Otto Mønsteds Fond and U.S. National Science Foundation (under grants DMS 1311558 and DMS 1712207) for their support. He thanks colleagues at DTU and KIT for their warm hospitality while this research was being done.

Analysis of large concrete storage tank under seismic response

Energy Technology Data Exchange (ETDEWEB)

Le, Jingyuan; Cui, Hongcheng; He, Qiang; Ju, Jinsan [China Agricultural University, Beijing (China); You, Xiaochuan [Tsinghua University, Beijing (China)

2015-01-15

This study adopted the finite element software ABAQUS to trace the dynamic response history of large reinforced concrete storage tank during different seismic excitations. The dynamic characteristics and failure modes of the tank's structure were investigated by considering the rebar's effect. Calculation results show that the large concrete storage tank remains in safe working conditions under a seismic acceleration of 55 cm/s{sup 2}. The joint of the concrete wall and dome begins to crack when seismic acceleration reaches 250 cm/s{sup 2}. As the earthquake continues, cracks spread until the top of the wall completely fails and stops working. The maximum displacement of the concrete tank and seismic acceleration are in proportion. Peak displacement and stress of the tank always appear behind the maximum acceleration.

Inverse Problem for 3D coupled Flow-Geomechanics Models and Induced Seismicity: Application to Subsurface Characterization and Seismicity Forecasting in Geologic CO2 Storage

Science.gov (United States)

Castineira, D.; Jha, B.; Juanes, R.

2016-12-01

Carbon Capture and Sequestration (CCS) is regarded as a promising technology to mitigate rising CO2 concentrations in the atmosphere from industrial emissions. However, as a result of the inherent uncertainty that is present in geological structures, assessing the stability of geological faults and quantifying the potential for induced seismicity is a fundamental challenge for practical implementation of CCS. Here we present a formal framework for the solution of the inverse problem associated with coupled flow and geomechanics models of CO2 injection and subsurface storage. Our approach builds from the application of Gaussian Processes, MCMC and posterior predictive analysis to evaluate relevant earthquake attributes (earthquake time, location and magnitude) in 3D synthetic models of CO2 storage under geologic, observational and operational uncertainty. In our approach, we first conduct hundreds of simulations of a high-fidelity 3D computational model for CO2 injection into a deep saline aquifer, dominated by an anticline structure and a fault. This ensemble of realizations accounts for uncertainty in the model parameters (including fault geomechanical and rock properties) and observations (earthquake time, location and magnitude). We apply Gaussian processes (GP) to generate a valid surrogate that closely approximates the behavior of the high fidelity (and computationally intensive) model, and apply hyperparameter optimization and cross-validation techniques in the solution of this multidimensional data-fit problem. The net result of this process is the generation of a fast model that can be effectively used for Bayesian analysis. We then implement Markov chain Monte Carlo (MCMC) to determine the posterior distribution of the model uncertain parameters (given some prior distributions for those parameters and given the likelihood defined in this case by the GP model). Our results show that the resulting posterior distributions correctly converge towards the "true

SH-wave reflection seismic and VSP as tools for the investigation of sinkhole areas in Germany

Science.gov (United States)

Wadas, Sonja; Tschache, Saskia; Polom, Ulrich; Buness, Hermann; Krawczyk, Charlotte M.

2017-04-01

Sinkholes can lead to damage of buildings and infrastructure and they can cause life-threatening situations, if they occur in urban areas. The process behind this phenomenon is called subrosion. Subrosion is the underground leaching of soluble rocks, e.g. anhydrite and gypsum, due to the contact with ground- and meteoric water. Depending on the leached material, and especially the dissolution rate, different kinds of subrosion structures evolve in the subsurface. The two end members are collapse and depression structures. For a better understanding of the subrosion processes a detailed characterization of the resulting structures is necessary. In Germany sinkholes are a problem in many areas. In northern Germany salt and in central and southern Germany sulfate and carbonate deposits are affected by subrosion. The study areas described here are located in Thuringia in central Germany and the underground is characterized by soluble Permian deposits. The occurrence of 20 to 50 sinkholes is reported per year. Two regions, Bad Frankenhausen and Schmalkalden, are investigated, showing a leaning church tower and a sinkhole of 30 m diameter and 20 m depth, respectively. In Bad Frankenhausen four P-wave and 16 SH-wave reflection seismic profiles were carried out, supplemented by three zero-offset VSPs. In Schmalkalden five SH-wave reflection seismic profiles and one zero-offset VSP were acquired. The 2-D seismic sections, in particular the SH-wave profiles, showed known and unknown near-surface faults in the vicinity of sinkholes and depressions. For imaging the near-surface ( 2,5, probably indicating unstable areas due to subrosion. We conclude, that SH-wave reflection seismic offer an important tool for the imaging and characterization of near-surface subrosion structures and the identification of unstable zones, especially in combination with P-wave reflection seismic and zero-offset VSP with P- and S-waves. Presumably there is a connection between the presence of large

Evaluation of seismic characteristics and structural integrity for the cabinet of HANARO seismic monitoring analysis system

Energy Technology Data Exchange (ETDEWEB)

Ryu, Jeong Soo; Yoon, Doo Byung

2003-06-01

The HANARO SMAS(Seismic Monitoring Analysis System) is classified as Non-Nuclear Safety(NNS), seismic category I, and quality class T. It is required that this system can perform required functions, which are to preserve its structural integrity during and after an OBE or SSE. In this work, the structural integrity and seismic characteristics of the cabinet of the newly developed SMAS have been estimated. The most parts of the cabinet are identically designed with those of Yonggwhang and Gori Nuclear Power Plants(NPPs), unit 1 that successfully completed the required seismic qualification tests. The structure of the cabinet of the SMAS is manufactured by the manufacturer of the cabinet of Yonggwhang and Gori NPPs. To evaluate the seismic characteristics of the SMAS, the RRS(Required Response Spectra) of the newly developed cabinet are compared with those of Yonggwhang and Gori NPPs, unit 1. In addition, natural frequencies of the cabinet of HANARO, Yonggwhang, and Gori NPPs were measured for the comparison of the seismic characteristics of the installed cabinets. In case of HANARO, the bottom of the cabinet is welded to the base plate. The base plate is fixed to the concrete foundation by using anchor bolts. For the evaluation of the structural integrity of the welding parts and the anchor bolts, the maximum stresses and forces of the welding parts and the anchor bolts due to seismic loading are estimated. The analysis results show that maximum stresses and forces are less than the allowable limits. This new SMAS is operating at HANARO instrument room to acquire and analyze the signal of earthquake.

Seismic Design of a Single Bored Tunnel: Longitudinal Deformations and Seismic Joints

Science.gov (United States)

Oh, J.; Moon, T.

2018-03-01

The large diameter bored tunnel passing through rock and alluvial deposits subjected to seismic loading is analyzed for estimating longitudinal deformations and member forces on the segmental tunnel liners. The project site has challenges including high hydrostatic pressure, variable ground profile and high seismic loading. To ensure the safety of segmental tunnel liner from the seismic demands, the performance-based two-level design earthquake approach, Functional Evaluation Earthquake and Safety Evaluation Earthquake, has been adopted. The longitudinal tunnel and ground response seismic analyses are performed using a three-dimensional quasi-static linear elastic and nonlinear elastic discrete beam-spring elements to represent segmental liner and ground spring, respectively. Three components (longitudinal, transverse and vertical) of free-field ground displacement-time histories evaluated from site response analyses considering wave passage effects have been applied at the end support of the strain-compatible ground springs. The result of the longitudinal seismic analyses suggests that seismic joint for the mitigation measure requiring the design deflection capacity of 5-7.5 cm is to be furnished at the transition zone between hard and soft ground condition where the maximum member forces on the segmental liner (i.e., axial, shear forces and bending moments) are induced. The paper illustrates how detailed numerical analyses can be practically applied to evaluate the axial and curvature deformations along the tunnel alignment under difficult ground conditions and to provide the seismic joints at proper locations to effectively reduce the seismic demands below the allowable levels.

Great Apes and Biodiversity Offset Projects in Africa: The Case for National Offset Strategies

Science.gov (United States)

Kormos, Rebecca; Kormos, Cyril F.; Humle, Tatyana; Lanjouw, Annette; Rainer, Helga; Victurine, Ray; Mittermeier, Russell A.; Diallo, Mamadou S.; Rylands, Anthony B.; Williamson, Elizabeth A.

2014-01-01

The development and private sectors are increasingly considering “biodiversity offsets” as a strategy to compensate for their negative impacts on biodiversity, including impacts on great apes and their habitats in Africa. In the absence of national offset policies in sub-Saharan Africa, offset design and implementation are guided by company internal standards, lending bank standards or international best practice principles. We examine four projects in Africa that are seeking to compensate for their negative impacts on great ape populations. Our assessment of these projects reveals that not all apply or implement best practices, and that there is little standardization in the methods used to measure losses and gains in species numbers. Even if they were to follow currently accepted best-practice principles, we find that these actions may still fail to contribute to conservation objectives over the long term. We advocate for an alternative approach in which biodiversity offset and compensation projects are designed and implemented as part of a National Offset Strategy that (1) takes into account the cumulative impacts of development in individual countries, (2) identifies priority offset sites, (3) promotes aggregated offsets, and (4) integrates biodiversity offset and compensation projects with national biodiversity conservation objectives. We also propose supplementary principles necessary for biodiversity offsets to contribute to great ape conservation in Africa. Caution should still be exercised, however, with regard to offsets until further field-based evidence of their effectiveness is available. PMID:25372894

Multi-parameter Full-waveform Inversion for Acoustic VTI Medium with Surface Seismic Data

Science.gov (United States)

Cheng, X.; Jiao, K.; Sun, D.; Huang, W.; Vigh, D.

2013-12-01

Full-waveform Inversion (FWI) attracts wide attention recently in oil and gas industry as a new promising tool for high resolution subsurface velocity model building. While the traditional common image point gather based tomography method aims to focus post-migrated data in depth domain, FWI aims to directly fit the observed seismic waveform in either time or frequency domain. The inversion is performed iteratively by updating the velocity fields to reduce the difference between the observed and the simulated data. It has been shown the inversion is very sensitive to the starting velocity fields, and data with long offsets and low frequencies is crucial for the success of FWI to overcome this sensitivity. Considering the importance of data with long offsets and low frequencies, in most geologic environment, anisotropy is an unavoidable topic for FWI especially at long offsets, since anisotropy tends to have more pronounced effects on waves traveled for a great distance. In VTI medium, this means more horizontal velocity will be registered in middle-to-long offset data, while more vertical velocity will be registered in near-to-middle offset data. Up to date, most of real world applications of FWI still remain in isotropic medium, and only a few studies have been shown to account for anisotropy. And most of those studies only account for anisotropy in waveform simulation, but not invert for those anisotropy fields. Multi-parameter inversion for anisotropy fields, even in VTI medium, remains as a hot topic in the field. In this study, we develop a strategy for multi-parameter FWI for acoustic VTI medium with surface seismic data. Because surface seismic data is insensitivity to the delta fields, we decide to hold the delta fields unchanged during our inversion, and invert only for vertical velocity and epsilon fields. Through parameterization analysis and synthetic tests, we find that it is more feasible to invert for the parameterization as vertical and horizontal

Seismic activity parameters of the Finnish potential repository sites

International Nuclear Information System (INIS)

Saari, J.

2000-10-01

Posiva Oy has started a project for estimating the possible earthquake induced rock movements on the deposition holes containing canisters of spent nuclear fuel. These estimates will be made for the four investigation sites, Romuvaara, Kivetty, Olkiluoto and Haestholmen. This study deals with the current and future seismicity associated with the above mentioned sites. Seismic belts that participate the seismic behaviour of the studied sites have been identified and the magnitude-frequency distributions of these belts have been estimated. The seismic activity parameters of the sites have been deduced from the characteristics of the seismic belts in order to forecast the seismicity during the next 100,000 years. The report discusses the possible earthquakes induced by future glaciation. The seismic interpretation seems to indicate that the previous postglacial faults in Finnish Lapland have been generated in compressional environment. The orientation of the rather uniform compression has been NW-SE, which coincide with the current stress field. It seems that, although the impact of postglacial crustal rebound must have been significant, the impact of plate tectonics has been dominant. A major assumption of this study has been that future seismicity will generally resemble the current seismicity. However, when the postglacial seismicity is concerned, the magnitude-frequency distribution is likely different and the expected maximum magnitude will be higher. Maximum magnitudes of future postglacial earthquakes have been approximated by strain release examinations. Seismicity has been examined within the framework of the lineament maps, in order to associate the future significant earthquakes with active fault zones in the vicinity of the potential repository sites. (orig.)

Development of seismic hazard analysis in Japan

International Nuclear Information System (INIS)

Itoh, T.; Ishii, K.; Ishikawa, Y.; Okumura, T.

1987-01-01

In recent years, seismic risk assessment of the nuclear power plant have been conducted increasingly in various countries, particularly in the United States to evaluate probabilistically the safety of existing plants under earthquake loading. The first step of the seismic risk assessment is the seismic hazard analysis, in which the relationship between the maximum earthquake ground motions at the plant site and their annual probability of exceedance, i.e. the seismic hazard curve, is estimated. In this paper, seismic hazard curves are evaluated and examined based on historical earthquake records model, in which seismic sources are modeled with area-sources, for several different sites in Japan. A new evaluation method is also proposed to compute the response spectra of the earthquake ground motions in connection with estimating the probabilistic structural response. Finally the numerical result of probabilistic risk assessment for a base-isolated three story RC structure, in which the frequency of seismic induced structural failure is evaluated combining the seismic hazard analysis, is described briefly

Investigation of sinkhole areas in Germany using 2D shear wave reflection seismics and zero-offset VSP

Science.gov (United States)

Tschache, Saskia; Wadas, Sonja; Polom, Ulrich; Krawczyk, Charlotte M.

2017-04-01

Sinkholes pose a serious geohazard for humans and infrastructure in populated areas. The Junior Research Group Subrosion within the Leibniz Institute for Applied Geophysics and the joint project SIMULTAN work on the multi-scale investigation of subrosion processes in the subsurface, which cause natural sinkholes. In two case studies in sinkhole areas of Thuringia in Germany, we applied 2D shear wave reflection seismics using SH-waves with the aim to detect suitable parameters for the characterisation of critical zones. This method has the potential to image near-surface collapse and faulting structures in improved resolution compared to P-wave surveys resulting from the shorter wavelength of shear waves. Additionally, the shear wave velocity field derived by NMO velocity analysis is a basis to calculate further physical parameters, as e.g. the dynamic shear modulus. In both investigation areas, vertical seismic profiles (VSP) were acquired by generating P- and SH-waves (6 component VSP) directly next to a borehole equipped with a 3C downhole sensor. They provide shear and compressional wave velocity profiles, which are used to improve the 2D shear wave velocity field from surface seismics, to perform a depth calibration of the seismic image and to calculate the Vp/Vs ratio. The signals in the VSP data are analysed with respect to changes in polarisation and attenuation with depth and/or azimuth. The VSP data reveal low shear wave velocities of 200-300 m/s in rock layers known to be heavily affected by subrosion and confirm the low velocities calculated from the surface seismic data. A discrepancy of the shear wave velocities is observed in other intervals probably due to unsymmetrical travel paths in the surface seismics. In some VSP data dominant conversion of the direct SH-wave to P-wave is observed that is assumed to be caused by an increased presence of cavities. A potential fault distorting the vertical travel paths was detected by abnormal P-wave first

Maximum Historical Seismic Intensity Map of S. Miguel Island (azores)

Science.gov (United States)

Silveira, D.; Gaspar, J. L.; Ferreira, T.; Queiroz, G.

The Azores archipelago is situated in the Atlantic Ocean where the American, African and Eurasian lithospheric plates meet. The so-called Azores Triple Junction located in the area where the Terceira Rift, a NW-SE to WNW-ESE fault system with a dextral component, intersects the Mid-Atlantic Ridge, with an approximate N-S direction, dominates its geological setting. S. Miguel Island is located in the eastern segment of the Terceira Rift, showing a high diversity of volcanic and tectonic structures. It is the largest Azorean island and includes three active trachytic central volcanoes with caldera (Sete Cidades, Fogo and Furnas) placed in the intersection of the NW-SE Ter- ceira Rift regional faults with an E-W deep fault system thought to be a relic of a Mid-Atlantic Ridge transform fault. N-S and NE-SW faults also occur in this con- text. Basaltic cinder cones emplaced along NW-SE fractures link that major volcanic structures. The easternmost part of the island comprises an inactive trachytic central volcano (Povoação) and an old basaltic volcanic complex (Nordeste). Since the settle- ment of the island, early in the XV century, several destructive earthquakes occurred in the Azores region. At least 11 events hit S. Miguel Island with high intensity, some of which caused several deaths and significant damages. The analysis of historical documents allowed reconstructing the history and the impact of all those earthquakes and new intensity maps using the 1998 European Macrosseismic Scale were produced for each event. The data was then integrated in order to obtain the maximum historical seismic intensity map of S. Miguel. This tool is regarded as an important document for hazard assessment and risk mitigation taking in account that indicates the location of dangerous seismogenic zones and provides a comprehensive set of data to be applied in land-use planning, emergency planning and building construction.

Seismic analysis for conceptual design of HCCR TBM-set

Energy Technology Data Exchange (ETDEWEB)

Lee, Dong Won, E-mail: dwlee@kaeri.re.kr [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Park, Seong Dae; Jin, Hyung Gon; Lee, Eo Hwak; Kim, Suk-Kwon; Yoon, Jae Sung [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Shin, Kyu In [Gentec Co., Daejeon, Republic of Korea (Korea, Republic of); Cho, Seungyon [National Fusion Research Institute, Daejeon (Korea, Republic of)

2016-11-01

Highlights: • The seismic analysis of KO HCCR TBM-set are performed. • The seismic envents like SL-1, SL-2, and SMHV are selected and evaluated with FEM code (ANSYS). • The results of the stresses and deformations are confirmed to meet the design criteria. - Abstract: Using the conceptual design of the Korean helium cooled ceramic reflector (HCCR) test blanket module (TBM) including the TBM-shield for testing in ITER, a seismic analysis is performed. According to the ITER TBM port plug (TBM PP) system load specifications, seismic events are selected as SL-1 (seismic level-1), SL-2 (seismic level-2), and SMHV (seismes maximaux historiquement vraisemblables, Maximum Histroically Probable Earthquakes). In a modal analysis a total of 50 modes are obtained. Then, a spectra response analysis for each seismic event is carried out using ANSYS based on the modal analysis results. For each event, the obtained Tresca stress is evaluated to confirm the design integrity, by comparing the resulting stress to the design criteria. The Tresca strain and displacement are also estimated for the HCCR TBM-set. From the analysis, it was concluded that the maximum stresses by the seismic events meet the design criteria, and the displacements are lower than the designed gap from the TBM PP frame. The results are provided to a load combination analysis.

Seismic sources in El Salvador. A geological and geodetic contribution

Science.gov (United States)

Alonso-Henar, J.; Martínez-Díaz, J. J.; Benito, B.; Alvarez-Gomez, J. A.; Canora, C.; Capote, R.; Staller, A.; Tectónica Activa, Paleosismicidad y. Riesgos Asociados UCM-910368

2013-05-01

El Salvador Fault Zone is a deformation band of 150 km long and 20 km wide within the Salvadorian volcanic arc. This shear band distributes the deformation between main strike-slip faults trending N90°-100°E and around 30 km long, and secondary normal faults trending between N120°E and N170°E. The ESFZ continues westward and is relieved by the Jalpatagua Fault. Eastward ESFZ becomes less clear disappearing at Golfo de Fonseca. The ESFZ deforms and offsets quaternary deposits with a right lateral movement in its main segments. Five segments have been proposed for the whole fault zone, from the Jalpatagua Fault to the Golfo de Fonseca. Paleoseismic studies in the Berlin and San Vicente Segments reveal an important amount of quaternary deformation. In fact, the San Vicente Segment was the source of the February 13, 2001 destructive earthquake. In this work we propose 18 capable seismic sources within El Salvador. The slip rate of each source has been obtained through out the combination of GPS data and paleoseismic data when it has been possible. We also have calculated maximum theoretical intensities produced by the maximum earthquakes related with each fault. We have taken into account several scenarios considering different possible surface rupture lengths up to 50 km and Mw 7.6 in some of the strike slip faults within ESFZ.

A Review of Offset Programs: Trading Systems, Funds, Protocols, Standards and Retailers

Energy Technology Data Exchange (ETDEWEB)

Kollmuss, Anja; Lazarus, Michael; Lee, Carrie; Polycarp, Clifford

2008-11-15

Carbon or greenhouse gas (GHG) offsets have long been promoted as an important element of a comprehensive climate policy approach. Offset programs can reduce the overall cost of achieving a given emission goal by enabling emission reductions to occur where costs are lower. Furthermore, offsets have the potential to deliver sustainability co-benefits, spurred through technology development and transfer, and to develop human and institutional capacity for reducing emissions in sectors and locations not included in a cap and trade or a mandatory government policy. However, offsets can pose a risk to the environmental integrity of climate actions, especially if issues surrounding additionality, permanence, leakage, quantification and verification are not adequately addressed. The challenge for policymakers is clear: to design offset programs and policies that can maximize their potential benefits while minimizing their potential risks. The goal of this review is to provide an up-to-date analysis and synthesis of the most influential offset programs and activities, to reflect on lessons learned, and thus to inform participants and designers of current and future offset programs. Our intention is to periodically update this review to stay abreast of ongoing developments, and to develop a website portal to make this information more accessible. This version targets programs that meet one or more of the following criteria: - a significant volume of credit transactions occurring or anticipated; - an established set of rules or protocols - path-breaking, novel or otherwise notable initiatives or important lessons learned

DIAGNOSTICS OF META-INSTABLE STATE OF SEISMICALLY ACTIVE FAULT

Directory of Open Access Journals (Sweden)

S. A. Bornyakov

2017-01-01

Full Text Available Based on the results of a laboratory simulation of the seismic fault reactivation by “stick-slip” process, it was shown that the system of two blocks just before an impulse offset goes through the meta-instable dynamic state, with early and late stages of meta-instability [Ma et al., 2012]. In the first stage the offset begins in slow stationary mode with slow stresses relaxation on contact between blocks. In the second stage of the “accelerated synergies” strain rate increases and, subsequently, the deformation process through a process of self-organization came to dynamic impulse offset. The experimental results were used for interpretation of the results of spectral analysis of the deformation monitoring data. The data were held within the southern part ofLakeBaikal, where Kultuk earthquake (27.08.2008, Ms=6.1. took place. Its epicenter was located in the South end zone of the main Sayan fault. Monitoring of deformations of rocks was carried out from April to November2008 in tunnel, located at30 km from the epicenter of the earthquake. The time series data was divided into month periods and then the periods were processed by the method of spectral analysis. The results showed that before the earthquake has ordered view spectrogram, whereas in other time intervals, both before and after the earthquake such orderliness in spectrograms is missing. An ordered view spectrograms for deformation monitoring data can be interpreted as a consequence of the self-organiza­tion of deformation process in the transition of seismically active fault into meta-unstable before the Kultuk earthquake.

Decadal-scale variability of diffuse CO2 emissions and seismicity revealed from long-term monitoring (1995–2013) at Mammoth Mountain, California, USA

Science.gov (United States)

Werner, Cynthia A.; Bergfeld, Deborah; Farrar, Chris; Doukas, Michael P.; Kelly, Peter; Kern, Christoph

2014-01-01

Mammoth Mountain, California, is a dacitic volcano that has experienced several periods of unrest since 1989. The onset of diffuse soil CO2 emissions at numerous locations on the flanks of the volcano began in 1989–1990 following an 11-month period of heightened seismicity. CO2 emission rates were measured yearly from 1995 to 2013 at Horseshoe Lake (HSL), the largest tree kill area on Mammoth Mountain, and measured intermittently at four smaller degassing areas around Mammoth from 2006 to 2013. The long-term record at HSL shows decadal-scale variations in CO2 emissions with two peaks in 2000–2001 and 2011–2012, both of which follow peaks in seismicity by 2–3 years. Between 2000 and 2004 emissions gradually declined during a seismically quiet period, and from 2004 to 2009 were steady at ~ 100 metric tonnes per day (t d− 1). CO2emissions at the four smaller tree-kill areas also increased by factors of 2–3 between 2006 and 2011–2012, demonstrating a mountain-wide increase in degassing. Delays between the peaks in seismicity and degassing have been observed at other volcanic and hydrothermal areas worldwide, and are thought to result from an injection of deep CO2-rich fluid into shallow subsurface reservoirs causing a pressurization event with a delayed transport to the surface. Such processes are consistent with previous studies at Mammoth, and here we highlight (1) the mountain-wide response, (2) the characteristic delay of 2–3 years, and (3) the roughly decadal reoccurrence interval for such behavior. Our best estimate of total CO2 degassing from Mammoth Mountain was 416 t d− 1 in 2011 during the peak of emissions, over half of which was emitted from HSL. The cumulative release of CO2 between 1995 and 2013 from diffuse emissions is estimated to be ~ 2–3 Mt, and extrapolation back to 1989 gives ~ 4.8 Mt. This amount of CO2 release is similar to that produced by the mid-sized (VEI 3) 2009 eruption of Redoubt Volcano in Alaska (~ 2.3�

Estimation of co-seismic stress change of the 2008 Wenchuan Ms8.0 earthquake

Energy Technology Data Exchange (ETDEWEB)

Sun Dongsheng; Wang Hongcai; Ma Yinsheng; Zhou Chunjing [Key laboratory of Neotectonic movement and Geohazard, Ministry of Land and Resources, Beijing 100081 (China) and Institute of Geomechanics, Chinese academy of Geological Sciences, Beijing 100081 (China)

2012-09-26

In-situ stress change near the fault before and after a great earthquake is a key issue in the geosciences field. In this work, based on the 2008 Great Wenchuan earthquake fault slip dislocation model, the co-seismic stress tensor change due to the Wenchuan earthquake and the distribution functions around the Longmen Shan fault are given. Our calculated results are almost consistent with the before and after great Wenchuan earthquake in-situ measuring results. The quantitative assessment results provide a reference for the study of the mechanism of earthquakes.

Analyzing the efficacy of subtropical urban forests in offsetting carbon emissions from cities

Science.gov (United States)

Francisco Escobedo; Sebastian Varela; Min Zhao; John E. Wagner; Wayne Zipperer

2010-01-01

Urban forest management and policies have been promoted as a tool to mitigate carbon dioxide (CO2) emissions. This study used existing CO2 reduction measures from subtropical Miami-Dade and Gainesville, USA and modeled carbon storage and sequestration by trees to analyze policies that use urban forests to offset carbon emissions. Field data were analyzed, modeled, and...

Are forestation, bio-char and landfilled biomass adequate offsets for the climate effects of burning fossil fuels?

International Nuclear Information System (INIS)

Reijnders, L.

2009-01-01

Forestation and landfilling purpose-grown biomass are not adequate offsets for the CO 2 emission from burning fossil fuels. Their permanence is insufficiently guaranteed and landfilling purpose-grown biomass may even be counterproductive. As to permanence, bio-char may do better than forests or landfilled biomass, but there are major uncertainties about net greenhouse gas emissions linked to the bio-char life cycle, which necessitate suspension of judgement about the adequacy of bio-char addition to soils as an offset for CO 2 emissions from burning fossil fuels.

Volcano dome dynamics at Mount St. Helens: Deformation and intermittent subsidence monitored by seismicity and camera imagery pixel offsets

Science.gov (United States)

Salzer, Jacqueline T.; Thelen, Weston A.; James, Mike R.; Walter, Thomas R.; Moran, Seth C.; Denlinger, Roger P.

2016-01-01

The surface deformation field measured at volcanic domes provides insights into the effects of magmatic processes, gravity- and gas-driven processes, and the development and distribution of internal dome structures. Here we study short-term dome deformation associated with earthquakes at Mount St. Helens, recorded by a permanent optical camera and seismic monitoring network. We use Digital Image Correlation (DIC) to compute the displacement field between successive images and compare the results to the occurrence and characteristics of seismic events during a 6 week period of dome growth in 2006. The results reveal that dome growth at Mount St. Helens was repeatedly interrupted by short-term meter-scale downward displacements at the dome surface, which were associated in time with low-frequency, large-magnitude seismic events followed by a tremor-like signal. The tremor was only recorded by the seismic stations closest to the dome. We find a correlation between the magnitudes of the camera-derived displacements and the spectral amplitudes of the associated tremor. We use the DIC results from two cameras and a high-resolution topographic model to derive full 3-D displacement maps, which reveals internal dome structures and the effect of the seismic activity on daily surface velocities. We postulate that the tremor is recording the gravity-driven response of the upper dome due to mechanical collapse or depressurization and fault-controlled slumping. Our results highlight the different scales and structural expressions during growth and disintegration of lava domes and the relationships between seismic and deformation signals.

Instantaneous response spectrum in seismic testing of nuclear power plant equipment

International Nuclear Information System (INIS)

Morrone, A.

1977-01-01

Seismic response spectra, as used in seismic analyses, give the maximum responses of single degree of freedom oscillators without consideration of the different time in the seismic time history at which each of the maximum responses occur. For response spectrum seismic analysis, the use of time-independent maximum responses is appropriate. The time dependece is considered in a statistical manner, for multi-degree of freedom systems, usually by combining the modal effects by the square root of the sum of the squares. For seismic testing of electrical equipment. IEEE Std. 344-1975 makes use of the response spectrum to define the input motion of the shake table. One of the basic requirements is that the test response spectrum (TRS) that is, the response spectrum produced by the shake table motion, should envelop the required response spectrum (RRS) calculated from the building analysis at the support point of the equipment being tested. This paper presents the concept of instantaneous response spectrum (IRS) as the response of single degree of freedom oscillators at a particular time. It demonstrates that a shake table random motion whose standard TRS envelops the RRS does not necessarily satisfy the enveloping requirement instantaneously. (Auth.)

High Performance Simulation of Large-Scale Red Sea Ocean Bottom Seismic Data on the Supercomputer Shaheen II

KAUST Repository

Tonellot, Thierry

2017-02-27

A combination of both shallow and deepwater, plus islands and coral reefs, are some of the main features contributing to the complexity of subsalt seismic exploration in the Red Sea transition zone. These features often result in degrading effects on seismic images. State-of-the-art ocean bottom acquisition technologies are therefore required to record seismic data with optimal fold and offset, as well as advanced processing and imaging techniques. Numerical simulations of such complex seismic data can help improve acquisition design and also help in customizing, validating and benchmarking the processing and imaging workflows that will be applied on the field data. Subsequently, realistic simulation of wave propagation is a computationally intensive process requiring a realistic model and an efficient 3D wave equation solver. Large-scale computing resources are also required to meet turnaround time compatible with a production time frame. In this work, we present the numerical simulation of an ocean bottom seismic survey to be acquired in the Red Sea transition zone starting in summer 2016. The survey\\'s acquisition geometry comprises nearly 300,000 unique shot locations and 21,000 unique receiver locations, covering about 760 km2. Using well log measurements and legacy 2D seismic lines in this area, a 3D P-wave velocity model was built, with a maximum depth of 7 km. The model was sampled at 10 m in each direction, resulting in more than 5 billion cells. Wave propagation in this model was performed using a 3D finite difference solver in the time domain based on a staggered grid velocity-pressure formulation of acoustodynamics. To ensure that the resulting data could be generated sufficiently fast, the King Abdullah University of Science and Technology (KAUST) supercomputer Shaheen II Cray XC40 was used. A total of 21,000 three-component (pressure and vertical and horizontal velocity) common receiver gathers with a 50 Hz maximum frequency were computed in less

High Performance Simulation of Large-Scale Red Sea Ocean Bottom Seismic Data on the Supercomputer Shaheen II

KAUST Repository

Tonellot, Thierry; Etienne, Vincent; Gashawbeza, Ewenet; Curiel, Emesto Sandoval; Khan, Azizur; Feki, Saber; Kortas, Samuel

2017-01-01

A combination of both shallow and deepwater, plus islands and coral reefs, are some of the main features contributing to the complexity of subsalt seismic exploration in the Red Sea transition zone. These features often result in degrading effects on seismic images. State-of-the-art ocean bottom acquisition technologies are therefore required to record seismic data with optimal fold and offset, as well as advanced processing and imaging techniques. Numerical simulations of such complex seismic data can help improve acquisition design and also help in customizing, validating and benchmarking the processing and imaging workflows that will be applied on the field data. Subsequently, realistic simulation of wave propagation is a computationally intensive process requiring a realistic model and an efficient 3D wave equation solver. Large-scale computing resources are also required to meet turnaround time compatible with a production time frame. In this work, we present the numerical simulation of an ocean bottom seismic survey to be acquired in the Red Sea transition zone starting in summer 2016. The survey's acquisition geometry comprises nearly 300,000 unique shot locations and 21,000 unique receiver locations, covering about 760 km2. Using well log measurements and legacy 2D seismic lines in this area, a 3D P-wave velocity model was built, with a maximum depth of 7 km. The model was sampled at 10 m in each direction, resulting in more than 5 billion cells. Wave propagation in this model was performed using a 3D finite difference solver in the time domain based on a staggered grid velocity-pressure formulation of acoustodynamics. To ensure that the resulting data could be generated sufficiently fast, the King Abdullah University of Science and Technology (KAUST) supercomputer Shaheen II Cray XC40 was used. A total of 21,000 three-component (pressure and vertical and horizontal velocity) common receiver gathers with a 50 Hz maximum frequency were computed in less than

A novel high-pressure vessel for simultaneous observations of seismic velocity and in situ CO2 distribution in a porous rock using a medical X-ray CT scanner

Science.gov (United States)

Jiang, Lanlan; Nishizawa, Osamu; Zhang, Yi; Park, Hyuck; Xue, Ziqiu

2016-12-01

Understanding the relationship between seismic wave velocity or attenuation and CO2 saturation is essential for CO2 storage in deep saline formations. In the present study, we describe a novel upright high-pressure vessel that is designed to keep a rock sample under reservoir conditions and simultaneously image the entire sample using a medical X-ray CT scanner. The pressure vessel is composed of low X-ray absorption materials: a carbon-fibre-enhanced polyetheretherketone (PEEK) cylinder and PEEK vessel closures supported by carbon-fibre-reinforced plastic (CFRP) joists. The temperature was controlled by a carbon-coated film heater and an aramid fibre thermal insulator. The assembled sample cell allows us to obtain high-resolution images of rock samples during CO2 drainage and brine imbibition under reservoir conditions. The rock sample was oriented vertical to the rotation axis of the CT scanner, and seismic wave paths were aligned parallel to the rotation axis to avoid shadows from the acoustic transducers. The reconstructed CO2 distribution images allow us to calculate the CO2 saturation in the first Fresnel zone along the ray path between transducers. A robust relationship between the seismic wave velocity or attenuation and the CO2 saturation in porous rock was obtained from experiments using this pressure vessel.

Leaf Dynamics of Panicum maximum under Future Climatic Changes.

Science.gov (United States)

Britto de Assis Prado, Carlos Henrique; Haik Guedes de Camargo-Bortolin, Lívia; Castro, Érique; Martinez, Carlos Alberto

2016-01-01

Panicum maximum Jacq. 'Mombaça' (C4) was grown in field conditions with sufficient water and nutrients to examine the effects of warming and elevated CO2 concentrations during the winter. Plants were exposed to either the ambient temperature and regular atmospheric CO2 (Control); elevated CO2 (600 ppm, eC); canopy warming (+2°C above regular canopy temperature, eT); or elevated CO2 and canopy warming (eC+eT). The temperatures and CO2 in the field were controlled by temperature free-air controlled enhancement (T-FACE) and mini free-air CO2 enrichment (miniFACE) facilities. The most green, expanding, and expanded leaves and the highest leaf appearance rate (LAR, leaves day(-1)) and leaf elongation rate (LER, cm day(-1)) were observed under eT. Leaf area and leaf biomass were higher in the eT and eC+eT treatments. The higher LER and LAR without significant differences in the number of senescent leaves could explain why tillers had higher foliage area and leaf biomass in the eT treatment. The eC treatment had the lowest LER and the fewest expanded and green leaves, similar to Control. The inhibitory effect of eC on foliage development in winter was indicated by the fewer green, expanded, and expanding leaves under eC+eT than eT. The stimulatory and inhibitory effects of the eT and eC treatments, respectively, on foliage raised and lowered, respectively, the foliar nitrogen concentration. The inhibition of foliage by eC was confirmed by the eC treatment having the lowest leaf/stem biomass ratio and by the change in leaf biomass-area relationships from linear or exponential growth to rectangular hyperbolic growth under eC. Besides, eC+eT had a synergist effect, speeding up leaf maturation. Therefore, with sufficient water and nutrients in winter, the inhibitory effect of elevated CO2 on foliage could be partially offset by elevated temperatures and relatively high P. maximum foliage production could be achieved under future climatic change.

Seismicity, state of stress and induced seismicity in the molasse basin and Jura (N-Switzerland)

Energy Technology Data Exchange (ETDEWEB)

Deichmann, N. [Schweizerischer Erdbebendienst, ETH Zuerich, Zuerich (Switzerland); Burlini, L. [Institut of Geology, ETH Zuerich, Zuerich (Switzerland)

2010-07-01

This illustrated report for the Swiss Federal Office of Energy (SFOE) is one of a series of appendices dealing with the potential for geological sequestration of CO{sub 2} in Switzerland. This report takes a look at the seismicity, state of stress and induced seismicity in the molasse basin and Jura Mountains in northern Switzerland. Data collected since 1983 by the Swiss Earthquake Service and the National Cooperative for the Disposal of Radioactive Wastes NAGRA on the tectonics and seismic properties of North-western Switzerland is noted. The results are illustrated with a number of maps and graphical representations and are discussed in detail. Cases of induced seismicity as resulting from both natural and man-made causes are examined.

Fault Mechanics and Post-seismic Deformation at Bam, SE Iran

Science.gov (United States)

Wimpenny, S. E.; Copley, A.

2017-12-01

The extent to which aseismic deformation relaxes co-seismic stress changes on a fault zone is fundamental to assessing the future seismic hazard following any earthquake, and in understanding the mechanical behaviour of faults. We used models of stress-driven afterslip and visco-elastic relaxation, in conjunction with a dense time series of post-seismic InSAR measurements, to show that there has been minimal release of co-seismic stress changes through post-seismic deformation following the 2003 Mw 6.6 Bam earthquake. Our modelling indicates that the faults at Bam may remain predominantly locked, and that the co- plus inter-seismically accumulated elastic strain stored down-dip of the 2003 rupture patch may be released in a future Mw 6 earthquake. Modelling also suggests parts of the fault that experienced post-seismic creep between 2003-2009 overlapped with areas that also slipped co-seismically. Our observations and models also provide an opportunity to probe how aseismic fault slip leads to the growth of topography at Bam. We find that, for our modelled afterslip distribution to be consistent with forming the sharp step in the local topography at Bam over repeated earthquake cycles, and also to be consistent with the geodetic observations, requires either (1) far-field tectonic loading equivalent to a 2-10 MPa deviatoric stress acting across the fault system, which suggests it supports stresses 60-100 times less than classical views of static fault strength, or (2) that the fault surface has some form of mechanical anisotropy, potentially related to corrugations on the fault plane, that controls the sense of slip.

Seismic safety of the LLL plutonium facility (Building 332)

International Nuclear Information System (INIS)

Torkarz, F.J.; Shaw, G.

1980-01-01

This report states the basis for the Lawrence Livermore Laboratory's assurance to the public that the plutonium operations at the Laboratory pose essentially no risk to anyone's health or safety, either under normal circumstances or in the event of an earthquake or a fire. The report is intended for a general audience, and so for the most part it is not highly technical. It summarizes the steps taken to ensure the seismic safety of the plutonium facility (Bldg. 332). It describes plutonium and its potential hazard and how the facility copes with that hazard. It recounts the geologic investigations and interpretations that led to the design-basis earthquake (DBE) for the Livermore site, and presents a summary analysis of the facility structure in relation to the DBE. An appendix presents a quantitative calculation of the health risk to the public associated with the worst-case hypothetical fire. The document supports the conclusions that the facility will continue to function safely after the maximum earthquake ground motion to which it may be subjected and that there is no evidence of a potential for surface offset under it

Seismic data are rich in information about subsurface formations and fluids

Energy Technology Data Exchange (ETDEWEB)

Farfour, Mohammed; Yoon, Wang Jung; Kim, Dongshin [Geophysical Prospecting Lab, Energy & Resources Eng., Dept., Chonnam National University, Gwangju (Korea, Republic of); Lee, Jeong-Hwan [Petroleum Engineering Lab, Energy & Resources Eng., Dept., Chonnam National University, Gwangju (Korea, Republic of)

2016-06-08

Seismic attributes are defined as any measured or computed information derived from seismic data. Throughout the last decades extensive work has been done in developing variety of mathematical approaches to extract maximum information from seismic data. Nevertheless, geoscientists found that seismic is still mature and rich in information. In this paper a new seismic attribute is introduced. Instantaneous energy seismic attribute is an amplitude based attribute that has the potential to emphasize anomalous amplitude associated with hydrocarbons. Promising results have been obtained from applying the attribute on seismic section traversing hydrocarbon filled sand from Alberta, Canada.

Some preliminary results of a worldwide seismicity estimation: a case study of seismic hazard evaluation in South America

Directory of Open Access Journals (Sweden)

C. V. Christova

2000-06-01

Full Text Available Global data have been widely used for seismicity and seismic hazard assessment by seismologists. In the present study we evaluate worldwide seismicity in terms of maps of maximum observed magnitude (Mmax, seismic moment (M 0 and seismic moment rate (M 0S. The data set used consists of a complete and homogeneous global catalogue of shallow (h £ 60 km earthquakes of magnitude MS ³ 5.5 for the time period 1894-1992. In order to construct maps of seismicity and seismic hazard the parameters a and b derived from the magnitude-frequency relationship were estimated by both: a the least squares, and b the maximum likelihood, methods. The values of a and b were determined considering circles centered at each grid point 1° (of a mesh 1° ´1° and of varying radius, which starts from 30 km and moves with a step of 10 km. Only a and b values which fulfill some predefined conditions were considered in the further procedure for evaluating the seismic hazard maps. The obtained worldwide M max distribution in general delineates the contours of the plate boundaries. The highest values of M max observed are along the circum-Pacific belt and in the Himalayan area. The subduction plate boundaries are characterized by the largest amount of M 0 , while areas of continental collision are next. The highest values of seismic moment rate (per 1 year and per equal area of 10 000 km 2 are found in the Southern Himalayas. The western coasts of U.S.A., Northwestern Canada and Alaska, the Indian Ocean and the eastern rift of Africa are characterized by high values of M 0 , while most of the Pacific subduction zones have lower values of seismic moment rate. Finally we analyzed the seismic hazard in South America comparing the predicted by the NUVEL1 model convergence slip rate between Nazca and South America plates with the average slip rate due to earthquakes. This consideration allows for distinguishing between zones of high and low coupling along the studied convergence

A combined method to calculate co-seismic displacements through strong motion acceleration baseline correction

Science.gov (United States)

Zhan, W.; Sun, Y.

2015-12-01

High frequency strong motion data, especially near field acceleration data, have been recorded widely through different observation station systems among the world. Due to tilting and a lot other reasons, recordings from these seismometers usually have baseline drift problems when big earthquake happens. It is hard to obtain a reasonable and precision co-seismic displacement through simply double integration. Here presents a combined method using wavelet transform and several simple liner procedures. Owning to the lack of dense high rate GNSS data in most of region of the world, we did not contain GNSS data in this method first but consider it as an evaluating mark of our results. This semi-automatic method unpacks a raw signal into two portions, a summation of high ranks and a low ranks summation using a cubic B-spline wavelet decomposition procedure. Independent liner treatments are processed against these two summations, which are then composed together to recover useable and reasonable result. We use data of 2008 Wenchuan earthquake and choose stations with a near GPS recording to validate this method. Nearly all of them have compatible co-seismic displacements when compared with GPS stations or field survey. Since seismometer stations and GNSS stations from observation systems in China are sometimes quite far from each other, we also test this method with some other earthquakes (1999 Chi-Chi earthquake and 2011 Tohoku earthquake). And for 2011 Tohoku earthquake, we will introduce GPS recordings to this combined method since the existence of a dense GNSS systems in Japan.

The voluntary offset - approaches and limitations

International Nuclear Information System (INIS)

2012-06-01

After having briefly presented the voluntary offset mechanism which aims at funding a project of reduction or capture of greenhouse gas emissions, this document describes the approach to be followed to adopt this voluntary offset, for individuals as well as for companies, communities or event organisations. It describes other important context issues (projects developed under the voluntary offset, actors of the voluntary offsetting market, market status, offset labels), and how to proceed in practice (definition of objectives and expectations, search for needed requirements, to ensure the meeting of requirements with respect to expectations). It addresses the case of voluntary offset in France (difficult implantation, possible solutions)

Seismic Investigations of an Accommodation zone in the Northern Rio Grande Rift, New Mexico, USA

Science.gov (United States)

Baldridge, W. S.; Valdes, J.; Nedorub, O.; Phrampus, B.; Braile, L. W.; Ferguson, J. F.; Benage, M. C.; Litherland, M.

2010-12-01

Seismic reflection and refraction data acquired in the Rio Grande rift near Santa Fe, New Mexico, in 2009 and 2010 by the SAGE (Summer of Applied Geophysical Experience) program imaged the La Bajada fault (LBF) and strata offset across the associated, perpendicular Budagher fault (BF). The LBF is a major basin-bounding normal fault, offset down to the west; the smaller BF is an extensional fault that breaks the hanging wall ramp of the LBF. We chose this area because it is in a structurally complex region of the rift, comprising a small sub-basin and plunging relay ramps, where north-trending, en echelon basin-bounding faults (including the LBF) transfer crustal extension laterally between the larger Española (to north) and Albuquerque rift basins. Our data help determine the precise location and geometry of the poorly exposed LBF, which, near the survey location, offsets the rift margin vertically about 3,000 m. When integrated with industry reflection data and other SAGE seismic, gravity, and magnetotelluric surveys, we are able to map differences in offset and extension laterally (especially southward) along the fault. We interpret only about 200 m of normal offset across the BF. Our continuing work helps define multiple structural elements, partly buried by syn-rift basin-filling sedimentary rocks, of a complex intra-rift accommodation zone. We are also able to discriminate pre-Eocene (Laramide) from post-Miocene (rift) structures. Our data help determine the amount of vertical offset of pre-rift strata across structural elements of the accommodation zone, and depth and geometry of basin fill. A goal is to infer the kinematic development of this margin of the rift, linkages among faults, growth history, and possible pre-rift structural controls. This information will be potentially useful for evaluation of resources, including oil and/or gas in pre-rift strata and ground water in Late Miocene to Holocene rift-filling units.

Verification of analysis methods for predicting the behaviour of seismically isolated nuclear structures. Final report of a co-ordinated research project 1996-1999

International Nuclear Information System (INIS)

2002-06-01

This report is a summary of the work performed under a co-ordinated research project (CRP) entitled Verification of Analysis Methods for Predicting the Behaviour of Seismically isolated Nuclear Structures. The project was organized by the IAEA on the recommendation of the IAEA's Technical Working Group on Fast Reactors (TWGFR) and carried out from 1996 to 1999. One of the primary requirements for nuclear power plants and facilities is to ensure safety and the absence of damage under strong external dynamic loading from, for example, earthquakes. The designs of liquid metal cooled fast reactors (LMFRs) include systems which operate at low pressure and include components which are thin-walled and flexible. These systems and components could be considerably affected by earthquakes in seismic zones. Therefore, the IAEA through its advanced reactor technology development programme supports the activities of Member States to apply seismic isolation technology to LMFRs. The application of this technology to LMFRs and other nuclear plants and related facilities would offer the advantage that standard designs may be safely used in areas with a seismic risk. The technology may also provide a means of seismically upgrading nuclear facilities. Design analyses applied to such critical structures need to be firmly established, and the CRP provided a valuable tool in assessing their reliability. Ten organizations from India, Italy, Japan, the Republic of Korea, the Russian Federation, the United Kingdom, the United States of America and the European Commission co-operated in this CRP. This report documents the CRP activities, provides the main results and recommendations and includes the work carried out by the research groups at the participating institutes within the CRP on verification of their analysis methods for predicting the behaviour of seismically isolated nuclear structures

Physics and seismic modeling for monitoring CO{sub 2} storage

Energy Technology Data Exchange (ETDEWEB)

Jose M. Carcione; Stefano Picotti; Davide Gei; Giuliana Rossi [Istituto Nazionale di Oceanografia e di Geofisica Sperimentale (OGS), Trieste (Italy)

2006-01-15

The authors present a new petro-elastical and numerical-simulation methodology to compute synthetic seismograms for reservoirs subject to CO{sub 2} sequestration. The petro-elastical equations model the seismic properties of reservoir rocks saturated with CO{sub 2}, methane, oil and brine. The gas properties are obtained from the van der Waals equation taking into account the absorption of gas by oil and brine, as a function of the in situ pore pressure and temperature. The dry-rock bulk and shear moduli can be obtained either by calibration from real data or by using rock-physics models based on the Hertz-Mindlin and Hashin-Shtrikman theories. Mesoscopic attenuation due to fluids effects is quantified by using White's model of patchy saturation, and the wet-rock velocities are calculated with Gassmann equations by using an effective fluid modulus to describe the velocities predicted by White's model. The simulations are performed with a poro-viscoelastic modeling code based on Biot's theory, where viscoelasticity is described by generalizing the solid/fluid coupling modulus to a relaxation function. Using the pseudo-spectral method, which allows general material variability, a complete and accurate characterization of the reservoir can be obtained. A simulation, that considers the Utsira sand of the North Sea, illustrates the methodology.

Measuring co-seismic deformation of the Sichuan earthquake by satellite differential INSAR

Science.gov (United States)

Zhang, Yonghong; Gong, Wenyu; Zhang, Jixian

2008-12-01

The Sichuan Earthquake, occurred on May 12, 2008, is the strongest earthquake to hit China since the 1976 Tangshan earthquake. The earthquake had a magnitude of M 8.0, and caused surface deformation greater than 3 meters. This paper presents the research work of measuring the co-seismic deformations of the earthquake with satellite differential interferometric SAR technique. Four L-band SAR images were used to form the interferogram with 2 pre- scenes imaged on Feb 17, 2008 and 2 post- scenes on May 19, 2008. The Digital Elevation Models extracted from 1:50,000-scale national geo-spatial database were used to remove the topographic contribution and form a differential interferogram. The interferogram presents very high coherence in most areas, although the pre- and post- images were acquired with time interval of 92 days. This indicates that the L-band PALSAR sensor is very powerful for interferometry applications. The baseline error is regarded as the main phase error source in the differential interferogram. Due to the difficulties of doing field works immediately after the earthquake, only one deformation measurement recorded by a permanent GPS station is obtained for this research. An approximation method is proposed to eliminate the orbital phase error with one control point. The derived deformation map shows similar spatial pattern and deformation magnitude compared with deformation field generated by seismic inversion method.

Comparison of Structurally Controlled Landslide Hazard Simulation to the Co-seismic Landslides Caused by the M 7.2 2013 Bohol Earthquake.

Science.gov (United States)

Galang, J. A. M. B.; Eco, R. C.; Lagmay, A. M. A.

2014-12-01

The M_w 7.2 October 15, 2013 Bohol earthquake is one of the more destructive earthquake to hit the Philippines in the 21st century. The epicenter was located in Sagbayan municipality, central Bohol and was generated by a previously unmapped reverse fault called the "Inabanga Fault". The earthquake resulted in 209 fatalities and over 57 million USD worth of damages. The earthquake generated co-seismic landslides most of which were related to fault structures. Unlike rainfall induced landslides, the trigger for co-seismic landslides happen without warning. Preparations for this type of landslides rely heavily on the identification of fracture-related slope instability. To mitigate the impacts of co-seismic landslide hazards, morpho-structural orientations of discontinuity sets were mapped using remote sensing techniques with the aid of a Digital Terrain Model (DTM) obtained in 2012. The DTM used is an IFSAR derived image with a 5-meter pixel resolution and approximately 0.5 meter vertical accuracy. Coltop 3D software was then used to identify similar structures including measurement of their dip and dip directions. The chosen discontinuity sets were then keyed into Matterocking software to identify potential rock slide zones due to planar or wedged discontinuities. After identifying the structurally-controlled unstable slopes, the rock mass propagation extent of the possible rock slides was simulated using Conefall. Separately, a manually derived landslide inventory has been performed using post-earthquake satellite images and LIDAR. The results were compared to the landslide inventory which identified at least 873 landslides. Out of the 873 landslides identified through the inventory, 786 or 90% intersect the simulated structural-controlled landslide hazard areas of Bohol. The results show the potential of this method to identify co-seismic landslide hazard areas for disaster mitigation. Along with computer methods to simulate shallow landslides, and debris flow

Ground magnetic studies along a regional seismic-reflection profile across Bare Mountain, Crater Flat and Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Langenheim, V.E.; Ponce, D.A.

1995-01-01

Ground magnetic data were collected along a 26-km-long regional seismic-reflection profile in southwest Nevada that starts in the Amargosa Desert, crosses Bare Mountain, Crater Flat and Yucca Mountain, and ends in Midway Valley. Parallel ground magnetic profiles were also collected about 100 m to either side of the western half of the seismic-reflection line. The magnetic data indicate that the eastern half of Crater Flat is characterized by closely-spaced faulting (1--2 km) in contrast to the western half of Crater Flat. Modeling of the data indicates that the Topopah Spring Tuff is offset about 250 m on the Solitario Canyon fault and about 50 m on the Ghost Dance fault. These estimates of fault offset are consistent with seismic-reflection data and geologic mapping. A broad magnetic high of about 500--600 nT is centered over Crater Flat. Modeling of the magnetic data indicates that the source of this high is not thickening and doming of the Bullfrog Tuff, but more likely lies below the Bullfrog Tuff. Possible source lithologies for this magnetic high include altered argillite of the Eleana Formation, Cretaceous or Tertiary intrusions, and mafic sills

A GPS Satellite Clock Offset Prediction Method Based on Fitting Clock Offset Rates Data

Directory of Open Access Journals (Sweden)

WANG Fuhong

2016-12-01

Full Text Available It is proposed that a satellite atomic clock offset prediction method based on fitting and modeling clock offset rates data. This method builds quadratic model or linear model combined with periodic terms to fit the time series of clock offset rates, and computes the model coefficients of trend with the best estimation. The clock offset precisely estimated at the initial prediction epoch is directly adopted to calculate the model coefficient of constant. The clock offsets in the rapid ephemeris (IGR provided by IGS are used as modeling data sets to perform certain experiments for different types of GPS satellite clocks. The results show that the clock prediction accuracies of the proposed method for 3, 6, 12 and 24 h achieve 0.43, 0.58, 0.90 and 1.47 ns respectively, which outperform the traditional prediction method based on fitting original clock offsets by 69.3%, 61.8%, 50.5% and 37.2%. Compared with the IGU real-time clock products provided by IGS, the prediction accuracies of the new method have improved about 15.7%, 23.7%, 27.4% and 34.4% respectively.

Domestic offset projects in the built environment

Energy Technology Data Exchange (ETDEWEB)

Oikonomou, V.; Spijker, E.; Van der Gaast, W. [Joint Implementation Network, Laan Corpus den Hoorn 300, 9728JT Groningen (Netherlands); Flamos, A.; Spyridaki, N.A. [Department of Industrial Management, University of Piraeus, Karaoli and Dimitriou 80 Str, 185 34 Piraeus (Greece)

2012-08-15

Emission reduction activities in the European Union (EU) in- and outside the European Trading System (ETS) thus far have largely taken place separately. One possibility to combine the two is through linking Non-ETS offset project-based crediting schemes in the form of Joint Implementation or domestic offset (DO) projects with the EU ETS. Linking would allow non-ETS offset project-based CO2 credits to be traded within the ETS market. This paper discusses the merits and drawbacks of the implementation of a DO scheme in the built environment in the Netherlands. The built environment can be characterised as a sector with a great diversity and significant energy savings potential. Emphasis is paid on the modalities for estimating energy savings under DO projects. The authors discuss if next to existing EU, national or regional policies in the Netherlands, DO could spur initiatives in sub-sectors or market areas that are difficult to reach with conventional policy instruments. Thus, despite the existing policy framework in this sector, there could be still space for DO to reach the untapped energy savings potential. DO can support activities and technologies that are not covered by other policy instruments, either because they are not part of the instruments focus or are above the minimum requirements of the incumbent policy targets. It is expected that some lessons from this study in the Netherlands can be taken into account also by other countries facing similar market circumstances, which have implemented several policy instruments and are considering DO schemes as an alternative for capturing part of the untapped energy saving potential in their end use sectors. Another possible advantage of DO is that it has the potential to reduce public spending on existing policy goals, when it is considered in conjunction with existing public financing instruments. In order to tap into this potential, there are a series of hurdles in place, like additionality and the current CO2

7 CFR 400.129 - Salary offset.

Science.gov (United States)

2010-01-01

... 7 Agriculture 6 2010-01-01 2010-01-01 false Salary offset. 400.129 Section 400.129 Agriculture... Years § 400.129 Salary offset. (a) Debt collection by salary offset is feasible if: the cost to the Government of collection by salary offset does not exceed the amount of the debt; there are no legal...

CO2 maximum in the oxygen minimum zone (OMZ

Directory of Open Access Journals (Sweden)

V. Garçon

2011-02-01

Full Text Available Oxygen minimum zones (OMZs, known as suboxic layers which are mainly localized in the Eastern Boundary Upwelling Systems, have been expanding since the 20th "high CO2" century, probably due to global warming. OMZs are also known to significantly contribute to the oceanic production of N2O, a greenhouse gas (GHG more efficient than CO2. However, the contribution of the OMZs on the oceanic sources and sinks budget of CO2, the main GHG, still remains to be established. We present here the dissolved inorganic carbon (DIC structure, associated locally with the Chilean OMZ and globally with the main most intense OMZs (O2−1 in the open ocean. To achieve this, we examine simultaneous DIC and O2 data collected off Chile during 4 cruises (2000–2002 and a monthly monitoring (2000–2001 in one of the shallowest OMZs, along with international DIC and O2 databases and climatology for other OMZs. High DIC concentrations (>2225 μmol kg−1, up to 2350 μmol kg−1 have been reported over the whole OMZ thickness, allowing the definition for all studied OMZs a Carbon Maximum Zone (CMZ. Locally off Chile, the shallow cores of the OMZ and CMZ are spatially and temporally collocated at 21° S, 30° S and 36° S despite different cross-shore, long-shore and seasonal configurations. Globally, the mean state of the main OMZs also corresponds to the largest carbon reserves of the ocean in subsurface waters. The CMZs-OMZs could then induce a positive feedback for the atmosphere during upwelling activity, as potential direct local sources of CO2. The CMZ paradoxically presents a slight "carbon deficit" in its core (~10%, meaning a DIC increase from the oxygenated ocean to the OMZ lower than the corresponding O2 decrease (assuming classical C/O molar ratios. This "carbon deficit" would be related to regional thermal mechanisms affecting faster O2 than DIC (due to the carbonate buffer effect and occurring upstream in warm waters (e.g., in the Equatorial Divergence

CO2 maximum in the oxygen minimum zone (OMZ)

Science.gov (United States)

Paulmier, A.; Ruiz-Pino, D.; Garçon, V.

2011-02-01

Oxygen minimum zones (OMZs), known as suboxic layers which are mainly localized in the Eastern Boundary Upwelling Systems, have been expanding since the 20th "high CO2" century, probably due to global warming. OMZs are also known to significantly contribute to the oceanic production of N2O, a greenhouse gas (GHG) more efficient than CO2. However, the contribution of the OMZs on the oceanic sources and sinks budget of CO2, the main GHG, still remains to be established. We present here the dissolved inorganic carbon (DIC) structure, associated locally with the Chilean OMZ and globally with the main most intense OMZs (O2Chile during 4 cruises (2000-2002) and a monthly monitoring (2000-2001) in one of the shallowest OMZs, along with international DIC and O2 databases and climatology for other OMZs. High DIC concentrations (>2225 μmol kg-1, up to 2350 μmol kg-1) have been reported over the whole OMZ thickness, allowing the definition for all studied OMZs a Carbon Maximum Zone (CMZ). Locally off Chile, the shallow cores of the OMZ and CMZ are spatially and temporally collocated at 21° S, 30° S and 36° S despite different cross-shore, long-shore and seasonal configurations. Globally, the mean state of the main OMZs also corresponds to the largest carbon reserves of the ocean in subsurface waters. The CMZs-OMZs could then induce a positive feedback for the atmosphere during upwelling activity, as potential direct local sources of CO2. The CMZ paradoxically presents a slight "carbon deficit" in its core (~10%), meaning a DIC increase from the oxygenated ocean to the OMZ lower than the corresponding O2 decrease (assuming classical C/O molar ratios). This "carbon deficit" would be related to regional thermal mechanisms affecting faster O2 than DIC (due to the carbonate buffer effect) and occurring upstream in warm waters (e.g., in the Equatorial Divergence), where the CMZ-OMZ core originates. The "carbon deficit" in the CMZ core would be mainly compensated locally at the

Seismic safety in conducting large-scale blasts

Science.gov (United States)

Mashukov, I. V.; Chaplygin, V. V.; Domanov, V. P.; Semin, A. A.; Klimkin, M. A.

2017-09-01

In mining enterprises to prepare hard rocks for excavation a drilling and blasting method is used. With the approach of mining operations to settlements the negative effect of large-scale blasts increases. To assess the level of seismic impact of large-scale blasts the scientific staff of Siberian State Industrial University carried out expertise for coal mines and iron ore enterprises. Determination of the magnitude of surface seismic vibrations caused by mass explosions was performed using seismic receivers, an analog-digital converter with recording on a laptop. The registration results of surface seismic vibrations during production of more than 280 large-scale blasts at 17 mining enterprises in 22 settlements are presented. The maximum velocity values of the Earth’s surface vibrations are determined. The safety evaluation of seismic effect was carried out according to the permissible value of vibration velocity. For cases with exceedance of permissible values recommendations were developed to reduce the level of seismic impact.

Structural Analysis and Seismic Design for Cold Neutron Laboratory Building

International Nuclear Information System (INIS)

Wu, Sangik; Kim, Y. K.; Kim, H. R.

2007-05-01

This report describes all the major results of the dynamic structural analysis and seismic design for the Cold Neutron Laboratory Building which is classified in seismic class II. The results are summarized of the ground response spectrum as seismic input loads, mechanical properties of subsoil, the buoyancy stability due to ground water, the maximum displacement of the main frame under the seismic load and the member design. This report will be used as a basic design report to maintenance its structural integrity in future

SU-E-J-259: Quantification of Rotational Localization Offset in Radiation Therapy

International Nuclear Information System (INIS)

Huang, Y; Nguyen, N; Lee, S; Liu, F

2014-01-01

Purpose: To verify the necessity of 6D localization detection and correction in radiation therapy. Methods: An anthropomorphic head and neck phantom was used to test the BrainLab ExacTrac x-ray imaging system. After initial positioning, both ExacTrac and the on-board kV CBCT were used to detect the offset at the same position, using both manual and automatic registration algorithms. Then 6D offset including rotational errors up to 5 degree were introduced. Both ExacTrac and CBCT were used to correct the offsets and the residual errors were evaluated. Finally, 6D offset detected by ExacTrac for a C-Spine patient was reported. Results: The differences in 3D offset detected by ExacTrac and CBCT were 1.5 ± 1.2(Lateral), 2.7 ± 2.7(Vertical), and 4.0 ± 6.3(longitudinal) mm with manual registration while the corresponding differences decreased to 0.6 ± 0.3, 1.0 ± 0.3, and 0.3 ± 0.3 when automatic registration were used. CBCT corrected the translational offset to within 0.5 mm but the rotational errors remained and detected by the ExacTrac system (Yaw=2.1, Roll=1.1, Pitch=1.4 degree). When similar offset was introduced and corrected using ExacTrac, the residual error detected by both CBCT and ExacTrac were within 0.5 mm / 0.5 degree. The average offset from the 112 ExacTrac x-ray corrections for the C-Spine patient was 0.6 ± 1.6 (lateral), 5.4 ± 8(vertical), 1.6±1.1(longitudinal) mm, and 0.7 ± 0.6 (pitch), 0.7 ± 0.4(roll), 1.2 ± 0.7 (yaw) degree. Larger rotational errors, with a maximum of 2.7 degree (corresponds to about 1.5 to 4.5 mm offset for a POI 10 to 30 cm away from the isocenter), were observed when couch rotational were involved. Conclusion: Rotational errors are common in patient localization, especially when couch rotation is involved. Both appropriate imaging system and 6D robotic couch are necessary to detect and correct the rotational localization errors

GPS and seismic constraints on the M = 7.3 2009 Swan Islands earthquake: implications for stress changes along the Motagua fault and other nearby faults

Science.gov (United States)

Graham, Shannon E.; DeMets, Charles; DeShon, Heather R.; Rogers, Robert; Maradiaga, Manuel Rodriguez; Strauch, Wilfried; Wiese, Klaus; Hernandez, Douglas

2012-09-01

We use measurements at 35 GPS stations in northern Central America and 25 seismometers at teleseismic distances to estimate the distribution of slip, source time function and Coulomb stress changes of the Mw = 7.3 2009 May 28, Swan Islands fault earthquake. This event, the largest in the region for several decades, ruptured the offshore continuation of the seismically hazardous Motagua fault of Guatemala, the site of the destructive Ms = 7.5 earthquake in 1976. Measured GPS offsets range from 308 millimetres at a campaign site in northern Honduras to 6 millimetres at five continuous sites in El Salvador. Separate inversions of geodetic and seismic data both indicate that up to ˜1 m of coseismic slip occurred along a ˜250-km-long rupture zone between the island of Roatan and the eastern limit of the 1976 M = 7.5 Motagua fault earthquake in Guatemala. Evidence for slip ˜250 km west of the epicentre is corroborated independently by aftershocks recorded by a local seismic network and by the high concentration of damage to structures in areas of northern Honduras adjacent to the western limit of the rupture zone. Coulomb stresses determined from the coseismic slip distribution resolve a maximum of 1 bar of stress transferred to the seismically hazardous Motagua fault and further indicate unclamping of normal faults along the northern shore of Honduras, where two M > 5 normal-faulting earthquakes and numerous small earthquakes were triggered by the main shock.

Three-dimensional seismic survey planning based on the newest data acquisition design technique; Saishin no data shutoku design ni motozuku sanjigen jishin tansa keikaku

Energy Technology Data Exchange (ETDEWEB)

Minehara, M; Nakagami, K; Tanaka, H [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

1996-10-01

Theory of parameter setting for data acquisition is arranged, mainly as to the seismic generating and receiving geometry. This paper also introduces an example of survey planning for three-dimensional land seismic exploration in progress. For the design of data acquisition, fundamental parameters are firstly determined on the basis of the characteristics of reflection records at a given district, and then, the layout of survey is determined. In this study, information through modeling based on the existing interpretation of geologic structures is also utilized, to reflect them for survey specifications. Land three-dimensional seismic survey was designed. Ground surface of the surveyed area consists of rice fields and hilly regions. The target was a nose-shaped structure in the depth about 2,500 m underground. A survey area of 4km{times}5km was set. Records in the shallow layers could not obtained when near offset was not ensured. Quality control of this distribution was important for grasping the shallow structure required. In this survey, the seismic generating point could be ensured more certainly than initially expected, which resulted in the sufficient security of near offset. 2 refs., 2 figs.

First-arrival Tomography Using the Double-square-root Equation Solver Stepping in Subsurface Offset

KAUST Repository

Serdyukov, A.S.

2013-01-01

Double-square-root (DSR) equation can be viewed as a Hamilton-Jacobi equation describing kinematics of downward data continuation in depth. It describes simultaneous propagation of source and receiver rays assuming that they are nowhere horizontal. Thus it is not suitable for describing diving waves. This equation can be rewritten in a new form when stepping is made in subsurface offset instead of depth. In this form it can be used for describing traveltimes of diving waves in prestack seismic data. This equation can be solved using WENO-RK numerical scheme. Prestack traveltimes (for multiple sources) can be computed in one run thus speeding up solution of the forward problem. We derive linearized version of this new DSR equation that can be used for tomographic inversion of first-arrival traveltimes. Here we used a ray-based tomographic inversion consisting of the following steps: get numerical solution of the offset DSR equation in the background velocity model, back trace DSR rays connecting receivers to sources, update velocity model using truncated SVD pseudoinverse. This approach was tested on a synthetic model generating diving waves.

Seismic test for safety evaluation of low level radioactive wastes containers

International Nuclear Information System (INIS)

Ohoka, Makoto; Horikiri, Morito

1998-08-01

Seismic safety of three-piled container system used in Tokai reprocessing center was confirmed by seismic test and computational analysis. Two types of container were evaluated, for low level noninflammable radioactive solid wastes, and for used filters wrapped by large plastic bags. Seismic integrity of three-piled containers was confirmed by evaluating response characteristics such as acceleration and displacement under the design earthquake condition S1, which is the maximum earthquake expected at the stored site during the storage time. Computational dynamic analysis was also performed, and several conclusions described below were made. (1) Response characteristics of the bottom board and the side board were different. The number of pile did not affect the response characteristics of the bottom board of each container. They behaved as a rigid body. (2) The response of the side board was larger than that of the bottom board. (3) The response depended on the direction in each board, either side or bottom. The response acceleration became larger to the seismic wave perpendicular to the plane which has the entrance for fork lift and the radioactive warning mark. (4) The maximum horizontal response displacement under the S1 seismic wave was approximately 10 mm. It is so small that it does not affect the seismic safety. (5) The stoppers to prevent fall down had no influence to the response acceleration. (6) There was no fall down to the S1 seismic wave and 2 times of S1 seismic wave, which was the maximum input condition of the test. (7) The response of the bottom board of the containers, which are main elements of fall down, had good agreements both in the test and in the computational analysis. (author)

Ensuring seismic safety of Blahutovice nuclear power plant

International Nuclear Information System (INIS)

Bartak, V.; David, M.; Hrabe, T.; Simunek, P.

1989-01-01

The results are presented of the seismic and geological survey of the Blahutovice nuclear power plant site. The variants are discussed of laying foundations and securing earthquake protection of the reactor building. The calculations made show that all variants are suitable with respect to seismic effects because the acceleration of seismic vibrations at the foundation slab level reaches the maximum intensity of 8deg MSK 64. The variant envisaging that the reactor building should be supported on spring insulators with viscous dampers is considered most advanced. (J.B.). 8 figs., 1 tab

Probabilistic seismic hazards: Guidelines and constraints in evaluating results

International Nuclear Information System (INIS)

Sadigh, R.K.; Power, M.S.

1989-01-01

In conducting probabilistic seismic hazard analyses, consideration of the dispersion as well as the upper bounds on ground motion is of great significance. In particular, the truncation of ground motion levels at some upper limit would have a major influence on the computed hazard at the low-to-very-low probability levels. Additionally, other deterministic guidelines and constraints should be considered in evaluating the probabilistic seismic hazard results. In contrast to probabilistic seismic hazard evaluations, mean plus one standard deviation ground motions are typically used for deterministic estimates of ground motions from maximum events that may affect a structure. To be consistent with standard deterministic maximum estimates of ground motions values should be the highest level considered for the site. These maximum values should be associated with the largest possible event occurring at the site. Furthermore, the relationships between the ground motion level and probability of exceedance should reflect a transition from purely probabilistic assessments of ground motion at high probability levels where there are multiple chances for events to a deterministic upper bound ground motion at very low probability levels where there is very limited opportunity for maximum events to occur. In Interplate Regions, where the seismic sources may be characterized by a high-to-very-high rate of activity, the deterministic bounds will be approached or exceeded by the computer probabilistic hazard values at annual probability of exceedance levels typically as high as 10 -2 to 10 -3 . Thus, at these or lower values probability levels, probabilistically computed hazard values could be readily interpreted in the light of the deterministic constraints

Waveform modeling of the seismic response of a mid-ocean ridge axial melt sill

Science.gov (United States)

Xu, Min; Stephen, R. A.; Canales, J. Pablo

2017-12-01

Seismic reflections from axial magma lens (AML) are commonly observed along many mid-ocean ridges, and are thought to arise from the negative impedance contrast between a solid, high-speed lid and the underlying low-speed, molten or partially molten (mush) sill. The polarity of the AML reflection ( P AML P) at vertical incidence and the amplitude vs offset (AVO) behavior of the AML reflections (e.g., P AML P and S-converted P AML S waves) are often used as a diagnostic tool for the nature of the low-speed sill. Time-domain finite difference calculations for two-dimensional laterally homogeneous models show some scenarios make the interpretation of melt content from partial-offset stacks of P- and S-waves difficult. Laterally heterogeneous model calculations indicate diffractions from the edges of the finite-width AML reducing the amplitude of the AML reflections. Rough seafloor and/or a rough AML surface can also greatly reduce the amplitude of peg-leg multiples because of scattering and destructive interference. Mid-crustal seismic reflection events are observed in the three-dimensional multi-channel seismic dataset acquired over the RIDGE-2000 Integrated Study Site at East Pacific Rise (EPR, cruise MGL0812). Modeling indicates that the mid-crustal seismic reflection reflections are unlikely to arise from peg-leg multiples of the AML reflections, P-to- S converted phases, or scattering due to rough topography, but could probably arise from deeper multiple magma sills. Our results support the identification of Marjanović et al. (Nat Geosci 7(11):825-829, 2014) that a multi-level complex of melt lenses is present beneath the axis of the EPR.

Fracturing and Transformation Into Veins Beneath the Crustal Scale Brittle Ductile Transition - a Record of Co-seismic Loading and Post-seismic Relaxation

Science.gov (United States)

Nüchter, J. A.; Stöckhert, B.

2005-12-01

Metamorphic rocks approaching the crustal scale brittle-ductile transition (BDT) during exhumation are expected to become increasingly affected by short term stress fluctuations related to seismic activity in the overlying seismogenic layer (schizosphere), while still residing in a long-term viscous environment (plastosphere). The structural and microstructural record of quartz veins in low grade - high pressure metamorphic rocks from southern Evia, Greece, yields insight into the processes and conditions just beneath the long-term BDT at temperatures of about 300 to 350°C, which switches between brittle failure and viscous flow as a function of imposed stress or strain rate. The following features are characteristic: (1) The veins have formed from tensile fractures, with a typical length on the order of 10-1 to 101 m; (2) The veins are discordant with respect to foliation and all pre-existing structures, with a uniform orientation over more than 500 km2; (3) The veins show a low aspect ratio of about 10 to 100 and an irregular or characteristic flame shape, which requires distributed ductile deformation of the host rock; (4) Fabrics of the sealing vein quartz indicate that - at a time - the veins were wide open cavities; (5) The sealing quartz crystals reveal a broad spectrum of microstructural features indicative of crystal plastic deformation at high stress and temperatures of about 300 to 350°C. These features indicate that opening and sealing of the fractures commenced immediately after brittle failure, controlled by ductile deformation of the host rock. Vein-parallel shortening was generally less than about 2%. Crystals formed early during sealing were plastically deformed upon progressive deformation and opening of the vein. The structural and microstructural record is interpreted as follows: Brittle failure is proposed to be a consequence of short term co-seismic loading. Subsequent opening of the fracture and sealing to become a vein is interpreted to

Implication of seismic attenuation for gas hydrate resource characterization, Mallik, Mackenzie Delta, Canada

Science.gov (United States)

Bellefleur, G.; Riedel, M.; Brent, T.; Wright, F.; Dallimore, S. R.

2007-10-01

Wave attenuation is an important physical property of hydrate-bearing sediments that is rarely taken into account in site characterization with seismic data. We present a field example showing improved images of hydrate-bearing sediments on seismic data after compensation of attenuation effects. Compressional quality factors estimated from zero-offset Vertical Seismic Profiling data acquired at Mallik, Northwest Territories, Canada, demonstrate significant wave attenuation for hydrate-bearing sediments. These results are in agreement with previous attenuation estimates obtained from sonic logs and crosshole data at different frequency intervals. The application of an inverse Q-filter to compensate attenuation effects of permafrost and hydrate-bearing sediments improved the resolution of surface 3D seismic data and its correlation with log data, particularly for the shallowest gas hydrate interval. Compensation of the attenuation effects of the permafrost likely explains most of the improvements for the shallow gas hydrate zone. Our results show that characterization of the Mallik gas hydrates with seismic data not corrected for attenuation would tend to overestimate thicknesses and lateral extent of hydrate-bearing strata and hence, the volume of hydrates in place.

How costly are carbon offsets? A meta-analysis of carbon forest sinks

NARCIS (Netherlands)

Kooten, van G.C.; Eagle, A.J.; Manley, J.; Smolak, T.

2004-01-01

Carbon terrestrial sinks are seen as a low-cost alternative to fuel switching and reduced fossil fuel use for lowering atmospheric CO2. As a result of agreements reached at Bonn and Marrakech, carbon offsets have taken on much greater importance in meeting Kyoto targets for the first commitment

NON-INVASIVE DETERMINATION OF THE LOCATION AND DISTRIBUTION OF FREE-PHASE DENSE NONAQUEOUS PHASE LIQUIDS (DNAPL) BY SEISMIC REFLECTION TECHNIQUES

Energy Technology Data Exchange (ETDEWEB)

Michael G. Waddell; William J. Domoracki; Tom J. Temples

2001-12-01

geometry. The AVO analysis located a major amplitude anomaly, which was tested using a Geoprobe{trademark} direct push system. The Geoprobe{trademark} was equipped with a membrane interface probe (MIP) that was interfaced with a sorbent trap/gas chromatograph (GC) system. Both the Photo Ionization Detector (PID) and Electron Capture Detector (ECD) on the GC exceeded the maximum measurement values through the anomaly. A well was installed to collect a water sample. The concentration of chlorinated solvents in the water sample was in excess of 500 ppm. Other amplitude anomalies located directly under an asphalt road were also tested. Both the PID and ECD were zero. It appears that editing of poor quality near-offset traces during data processing caused these anomalies. Not having the full range of source to receiver offset traces in those areas resulted in a false anomaly during AVO analysis. This phenomenon was also observed at the beginning and end of each seismic profile also for the same reason. Based upon the water samples and MIP probes, it appears that surface seismic and AVO analysis were able to detect the area of highest concentration of DNAPL.

Combined Gravimetric-Seismic Crustal Model for Antarctica

Science.gov (United States)

Baranov, Alexey; Tenzer, Robert; Bagherbandi, Mohammad

2018-01-01

The latest seismic data and improved information about the subglacial bedrock relief are used in this study to estimate the sediment and crustal thickness under the Antarctic continent. Since large parts of Antarctica are not yet covered by seismic surveys, the gravity and crustal structure models are used to interpolate the Moho information where seismic data are missing. The gravity information is also extended offshore to detect the Moho under continental margins and neighboring oceanic crust. The processing strategy involves the solution to the Vening Meinesz-Moritz's inverse problem of isostasy constrained on seismic data. A comparison of our new results with existing studies indicates a substantial improvement in the sediment and crustal models. The seismic data analysis shows significant sediment accumulations in Antarctica, with broad sedimentary basins. According to our result, the maximum sediment thickness in Antarctica is about 15 km under Filchner-Ronne Ice Shelf. The Moho relief closely resembles major geological and tectonic features. A rather thick continental crust of East Antarctic Craton is separated from a complex geological/tectonic structure of West Antarctica by the Transantarctic Mountains. The average Moho depth of 34.1 km under the Antarctic continent slightly differs from previous estimates. A maximum Moho deepening of 58.2 km under the Gamburtsev Subglacial Mountains in East Antarctica confirmed the presence of deep and compact orogenic roots. Another large Moho depth in East Antarctica is detected under Dronning Maud Land with two orogenic roots under Wohlthat Massif (48-50 km) and the Kottas Mountains (48-50 km) that are separated by a relatively thin crust along Jutulstraumen Rift. The Moho depth under central parts of the Transantarctic Mountains reaches 46 km. The maximum Moho deepening (34-38 km) in West Antarctica is under the Antarctic Peninsula. The Moho depth minima in East Antarctica are found under the Lambert Trench (24

Seismic risk map of Korea

International Nuclear Information System (INIS)

Lee, S.H.; Lee, Y.K.; Eum, S.H.; Yang, S.J.; Chun, M.S.

1983-01-01

A study on seismic hazard level in Korea has been performed and the main results of the study are summarized as follows: 1. Historians suggest that the quality of historical earthquake data may be accurate in some degree and the data should be used in seismic risk analysis. 2. The historical damage events are conformed in historical literatures and their intensities are re-evaluated by joint researchers. The maximum MM intensity of them is VIII evaluated for 17 events. 3. The relation of earthquakes to surface fault is not clear. It seems resonable to related them to tectonic provinces. 4. Statistical seismic risk analysis shows that the acceleration expected within 50O year return period is less than 0.25G when only instrumental earthquakes are used and less than 0.10G if all of instrumental and historical earthquakes are used. The acceleration in Western Coast and Kyungsang area is higher than the other regions in Korea. 5. The maximum horizontal acceleration determined by conservative method is 0.26G when historical earthquake data are used and less than 0.20G if only instrumental earthquakes are used. The return period of 0.26G is 240 years in Kyungsang province and longer in other provinces. (Author)

Probabilistic seismic hazard assessment. Gentilly 2

International Nuclear Information System (INIS)

1996-03-01

Results of this probabilistic seismic hazard assessment were determined using a suite of conservative assumptions. The intent of this study was to perform a limited hazard assessment that incorporated a range of technically defensible input parameters. To best achieve this goal, input selected for the hazard assessment tended to be conservative with respect to selection of attenuation modes, and seismicity parameters. Seismic hazard estimates at Gentilly 2 were most affected by selection of the attenuation model. Alternative definitions of seismic source zones had a relatively small impact on seismic hazard. A St. Lawrence Rift model including a maximum magnitude of 7.2 m b in the zone containing the site had little effect on the hazard estimate relative to other seismic source zonation models. Mean annual probabilities of exceeding the design peak ground acceleration, and the design response spectrum for the Gentilly 2 site were computed to lie in the range of 0.001 to 0.0001. This hazard result falls well within the range determined to be acceptable for nuclear reactor sites located throughout the eastern United States. (author) 34 refs., 6 tabs., 28 figs

Low Offset AC Correlator.

Science.gov (United States)

This patent describes a low offset AC correlator avoids DC offset and low frequency noise by frequency operating the correlation signal so that low...noise, low level AC amplification can be substituted for DC amplification. Subsequently, the high level AC signal is demodulated to a DC level. (Author)

Post-seismic velocity changes following the 2010 Mw 7.1 Darfield earthquake, New Zealand, revealed by ambient seismic field analysis

Science.gov (United States)

Heckels, R. EG; Savage, M. K.; Townend, J.

2018-05-01

Quantifying seismic velocity changes following large earthquakes can provide insights into fault healing and reloading processes. This study presents temporal velocity changes detected following the 2010 September Mw 7.1 Darfield event in Canterbury, New Zealand. We use continuous waveform data from several temporary seismic networks lying on and surrounding the Greendale Fault, with a maximum interstation distance of 156 km. Nine-component, day-long Green's functions were computed for frequencies between 0.1 and 1.0 Hz for continuous seismic records from immediately after the 2010 September 04 earthquake until 2011 January 10. Using the moving-window cross-spectral method, seismic velocity changes were calculated. Over the study period, an increase in seismic velocity of 0.14 ± 0.04 per cent was determined near the Greendale Fault, providing a new constraint on post-seismic relaxation rates in the region. A depth analysis further showed that velocity changes were confined to the uppermost 5 km of the subsurface. We attribute the observed changes to post-seismic relaxation via crack healing of the Greendale Fault and throughout the surrounding region.

Preliminary Seismic Response and Fragility Analysis for DACS Cabinet

Energy Technology Data Exchange (ETDEWEB)

Oh, Jinho; Kwag, Shinyoung; Lee, Jongmin; Kim, Youngki [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-05-15

A DACS cabinet is installed in the main control room. The objective of this paper is to perform seismic analyses and evaluate the preliminary structural integrity and seismic capacity of the DACS cabinet. For this purpose, a 3-D finite element model of the DACS cabinet was developed and its modal analyses are carried out to analyze the dynamic characteristics. The response spectrum analyses and the related safety evaluation are then performed for the DACS cabinet subject to seismic loads. Finally, the seismic margin and seismic fragility of the DACS cabinet are investigated. A seismic analysis and preliminary structural integrity of the DACS cabinet under self weight and SSE load have been evaluated. For this purpose, 3-D finite element models of the DACS cabinet were developed. A modal analysis, response spectrum analysis, and seismic fragility analysis were then performed. From the structural analysis results, the DACS cabinet is below the structural design limit of under SSE 0.3g, and can structurally withstand until less than SSE 3g based on an evaluation of the maximum effective stresses. The HCLPF capacity for the DGRS of the SSE 0.3g is 0.55g. A modal analysis, response spectrum analysis, and seismic fragility analysis were then performed. From the structural analysis results, the DACS cabinet is below the structural design limit of under SSE 0.3g, and can structurally withstand until less than SSE 3g based on an evaluation of the maximum effective stresses. The HCLPF capacity for the DGRS of the SSE 0.3g is 0.55g. Therefore, it is concluded that the DACS cabinet was safely designed in that no damage to the preliminary structural integrity and sufficient seismic margin is expected.

Preliminary Seismic Response and Fragility Analysis for DACS Cabinet

International Nuclear Information System (INIS)

Oh, Jinho; Kwag, Shinyoung; Lee, Jongmin; Kim, Youngki

2013-01-01

A DACS cabinet is installed in the main control room. The objective of this paper is to perform seismic analyses and evaluate the preliminary structural integrity and seismic capacity of the DACS cabinet. For this purpose, a 3-D finite element model of the DACS cabinet was developed and its modal analyses are carried out to analyze the dynamic characteristics. The response spectrum analyses and the related safety evaluation are then performed for the DACS cabinet subject to seismic loads. Finally, the seismic margin and seismic fragility of the DACS cabinet are investigated. A seismic analysis and preliminary structural integrity of the DACS cabinet under self weight and SSE load have been evaluated. For this purpose, 3-D finite element models of the DACS cabinet were developed. A modal analysis, response spectrum analysis, and seismic fragility analysis were then performed. From the structural analysis results, the DACS cabinet is below the structural design limit of under SSE 0.3g, and can structurally withstand until less than SSE 3g based on an evaluation of the maximum effective stresses. The HCLPF capacity for the DGRS of the SSE 0.3g is 0.55g. A modal analysis, response spectrum analysis, and seismic fragility analysis were then performed. From the structural analysis results, the DACS cabinet is below the structural design limit of under SSE 0.3g, and can structurally withstand until less than SSE 3g based on an evaluation of the maximum effective stresses. The HCLPF capacity for the DGRS of the SSE 0.3g is 0.55g. Therefore, it is concluded that the DACS cabinet was safely designed in that no damage to the preliminary structural integrity and sufficient seismic margin is expected

Ultra-thin clay layers facilitate seismic slip in carbonate faults.

Science.gov (United States)

Smeraglia, Luca; Billi, Andrea; Carminati, Eugenio; Cavallo, Andrea; Di Toro, Giulio; Spagnuolo, Elena; Zorzi, Federico

2017-04-06

Many earthquakes propagate up to the Earth's surface producing surface ruptures. Seismic slip propagation is facilitated by along-fault low dynamic frictional resistance, which is controlled by a number of physico-chemical lubrication mechanisms. In particular, rotary shear experiments conducted at seismic slip rates (1 ms -1 ) show that phyllosilicates can facilitate co-seismic slip along faults during earthquakes. This evidence is crucial for hazard assessment along oceanic subduction zones, where pelagic clays participate in seismic slip propagation. Conversely, the reason why, in continental domains, co-seismic slip along faults can propagate up to the Earth's surface is still poorly understood. We document the occurrence of micrometer-thick phyllosilicate-bearing layers along a carbonate-hosted seismogenic extensional fault in the central Apennines, Italy. Using friction experiments, we demonstrate that, at seismic slip rates (1 ms -1 ), similar calcite gouges with pre-existing phyllosilicate-bearing (clay content ≤3 wt.%) micro-layers weaken faster than calcite gouges or mixed calcite-phyllosilicate gouges. We thus propose that, within calcite gouge, ultra-low clay content (≤3 wt.%) localized along micrometer-thick layers can facilitate seismic slip propagation during earthquakes in continental domains, possibly enhancing surface displacement.

5 CFR 179.307 - Administrative offset.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Administrative offset. 179.307 Section 179.307 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS CLAIMS COLLECTION STANDARDS Administrative Offset § 179.307 Administrative offset. (a) If the debtor does not...

Astor Pass Seismic Surveys Preliminary Report

Energy Technology Data Exchange (ETDEWEB)

Louie, John [UNR; Pullammanappallil, Satish [Optim; Faulds, James; Eisses, Amy; Kell, Annie; Frary, Roxanna; Kent, Graham

2011-08-05

activity do not have enough offset to produce seismic terminations. We are conducting further high-resolution seismic studies (to 200 ft depths) at the tufa spire to test this hypothesis. Additional work in progress includes a collaborative, iterative joint interpretation of geologic mapping and the seismic sections for fault locations, building the geologic model; and 3d velocity modeling and imaging to locate additional faultplane images appearing between the 2d lines. Overall, the seismic exploration program cost less than $0.5M from all funders. It defines in detail the geologic structure of much of the north margin of Pyramid Lake.

Development of seismic tomography software for hybrid supercomputers

Science.gov (United States)

Nikitin, Alexandr; Serdyukov, Alexandr; Duchkov, Anton

2015-04-01

Seismic tomography is a technique used for computing velocity model of geologic structure from first arrival travel times of seismic waves. The technique is used in processing of regional and global seismic data, in seismic exploration for prospecting and exploration of mineral and hydrocarbon deposits, and in seismic engineering for monitoring the condition of engineering structures and the surrounding host medium. As a consequence of development of seismic monitoring systems and increasing volume of seismic data, there is a growing need for new, more effective computational algorithms for use in seismic tomography applications with improved performance, accuracy and resolution. To achieve this goal, it is necessary to use modern high performance computing systems, such as supercomputers with hybrid architecture that use not only CPUs, but also accelerators and co-processors for computation. The goal of this research is the development of parallel seismic tomography algorithms and software package for such systems, to be used in processing of large volumes of seismic data (hundreds of gigabytes and more). These algorithms and software package will be optimized for the most common computing devices used in modern hybrid supercomputers, such as Intel Xeon CPUs, NVIDIA Tesla accelerators and Intel Xeon Phi co-processors. In this work, the following general scheme of seismic tomography is utilized. Using the eikonal equation solver, arrival times of seismic waves are computed based on assumed velocity model of geologic structure being analyzed. In order to solve the linearized inverse problem, tomographic matrix is computed that connects model adjustments with travel time residuals, and the resulting system of linear equations is regularized and solved to adjust the model. The effectiveness of parallel implementations of existing algorithms on target architectures is considered. During the first stage of this work, algorithms were developed for execution on

New seismic sources parameterization in El Salvador. Implications to seismic hazard.

Science.gov (United States)

Alonso-Henar, Jorge; Staller, Alejandra; Jesús Martínez-Díaz, José; Benito, Belén; Álvarez-Gómez, José Antonio; Canora, Carolina

2014-05-01

El Salvador is located at the pacific active margin of Central America, here, the subduction of the Cocos Plate under the Caribbean Plate at a rate of ~80 mm/yr is the main seismic source. Although the seismic sources located in the Central American Volcanic Arc have been responsible for some of the most damaging earthquakes in El Salvador. The El Salvador Fault Zone is the main geological structure in El Salvador and accommodates 14 mm/yr of horizontal displacement between the Caribbean Plate and the forearc sliver. The ESFZ is a right lateral strike-slip fault zone c. 150 km long and 20 km wide .This shear band distributes the deformation among strike-slip faults trending N90º-100ºE and secondary normal faults trending N120º- N170º. The ESFZ is relieved westward by the Jalpatagua Fault and becomes less clear eastward disappearing at Golfo de Fonseca. Five sections have been proposed for the whole fault zone. These fault sections are (from west to east): ESFZ Western Section, San Vicente Section, Lempa Section, Berlin Section and San Miguel Section. Paleoseismic studies carried out in the Berlin and San Vicente Segments reveal an important amount of quaternary deformation and paleoearthquakes up to Mw 7.6. In this study we present 45 capable seismic sources in El Salvador and their preliminary slip-rate from geological and GPS data. The GPS data detailled results are presented by Staller et al., 2014 in a complimentary communication. The calculated preliminary slip-rates range from 0.5 to 8 mm/yr for individualized faults within the ESFZ. We calculated maximum magnitudes from the mapped lengths and paleoseismic observations.We propose different earthquakes scenario including the potential combined rupture of different fault sections of the ESFZ, resulting in maximum earthquake magnitudes of Mw 7.6. We used deterministic models to calculate acceleration distribution related with maximum earthquakes of the different proposed scenario. The spatial distribution of

41 CFR 105-56.018 - Salary offset.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Salary offset. 105-56... Administration 56-SALARY OFFSET FOR INDEBTEDNESS OF FEDERAL EMPLOYEES TO THE UNITED STATES Centralized Salary Offset (CSO) Procedures-GSA as Creditor Agency § 105-56.018 Salary offset. When a match occurs and all...

41 CFR 105-56.028 - Salary offset.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Salary offset. 105-56... Administration 56-SALARY OFFSET FOR INDEBTEDNESS OF FEDERAL EMPLOYEES TO THE UNITED STATES Centralized Salary Offset (CSO) Procedures-GSA as Paying Agency § 105-56.028 Salary offset. When a match occurs and all...

Seismic fragility capacity of equipment--horizontal shaft pump test

International Nuclear Information System (INIS)

Iijima, T.; Abe, H.; Suzuki, K.

2005-01-01

The current seismic fragility capacity of horizontal shaft pump is 1.6 x 9.8 m/s 2 (1.6 g), which was decided from previous vibration tests and we believe that it must have sufficient margin. The purpose of fragility capacity test is to obtain realistic seismic fragility capacity of horizontal shaft pump by vibration tests. Reactor Building Closed Cooling Water (RCW) Pump was tested as a typical horizontal shaft pump, and then bearings and liner rings were tested as important parts to evaluate critical acceleration and dispersion. Regarding RCW pump test, no damage was found, though maximum input acceleration level was 6 x 9.8 m/s 2 (6 g). Some kinds of bearings and liner rings were tested on the element test. Input load was based on seismic motion which was same with the RCW pump test, and maximum load was equivalent to over 20 times of design seismic acceleration. There was not significant damage that caused emergency stop of pump but degradation of surface roughness was found on some kinds of bearings. It would cause reduction of pump life, but such damage on bearings occurred under large seismic load condition that was equivalent to over 10 to 20 g force. Test results show that realistic fragility capacity of horizontal shaft pump would be at least four times as higher as current value which has been used for our seismic PSA. (authors)

Method to measure the position offset of multiple light spots in a distributed aperture laser angle measurement system.

Science.gov (United States)

Jing, Xiaoli; Cheng, Haobo; Xu, Chunyun; Feng, Yunpeng

2017-02-20

In this paper, an accurate measurement method of multiple spots' position offsets on a four-quadrant detector is proposed for a distributed aperture laser angle measurement system (DALAMS). The theoretical model is put forward, as well as the corresponding calculation method. This method includes two steps. First, as the initial estimation, integral approximation is applied to fit the distributed spots' offset function; second, the Boltzmann function is employed to compensate for the estimation error to improve detection accuracy. The simulation results attest to the correctness and effectiveness of the proposed method, and tolerance synthesis analysis of DALAMS is conducted to determine the maximum uncertainties of manufacturing and installation. The maximum angle error is less than 0.08° in the prototype distributed measurement system, which shows the stability and robustness for prospective applications.

Baseline studies to select the most sound and sensitive sites to install continuous monitoring per sismo-geochemical networks. The case history of the Norcia-Amatrice-Spoleto seismic sequences (2016-2017)

Science.gov (United States)

Quattrocchi, F.; Gallo, F.

2017-12-01

The paper review methodologically and historically - in the frame of seismo-geochemical studies in Italy and abroad to select the most "sensitive" sites along active faults, mostly where structural geology is not able to discover "blind" faults or complex fault crossing systems, with maximum fluids-faults interaction. The paper is highlighting the "site specific" case histories and processes helping in networks design, gathered in occasion of strong-moderate earthquakes, gas-burst or groundwater evolution in geothermal-hydrocarbons field during EU projects (i.e., Geochemical Seismic Zonation, 3F-Faults-Fractures-Fluids Corinth). Some concepts are highlighted based on gather experimental data in 25 years: - if the network is in soil gas is necessary a preliminary study on groundwater too, to understand the sectors of shallow aquifers, as "buffer" bodies, more prone to be oversaturated by geogas from depth; a preliminary grid should consider both the CO2-CH4-Rn fluxes, all gas concentrations and isotopes analyses (TDIC, CH4 CO2 , rare gas) case by case described here, mostly where the regional faults are crossing each other and where a carrier gas is acting i.e., CO2. It is very un-correct to install mono-parametric stations, i.e. only Radon to understand the real WRI processes. - if the network is in groundwater is very important a preliminary study before, during and after seismic sequences, to realize where the maximum anomalies (i.e., anomalous animal behavior, temperature increasing, geochemical anomalies, new gas relase) are and will be envisaged, as found for the Umbria-Marche border (the Colfiorito 1997-1998 and the 2016-2017 Norcia-Amatrice seismic sequences), where a deep pore-pressure dominated situation could be constrained by seismo-geochemistry, along "still silent" close fault segments too. if the network is in groundwater is very important a geochemical multidisciplinary approach to constrain the segment length and relative maximum magnitude.

34 CFR 31.11 - Offset process.

Science.gov (United States)

2010-07-01

... 34 Education 1 2010-07-01 2010-07-01 false Offset process. 31.11 Section 31.11 Education Office of the Secretary, Department of Education SALARY OFFSET FOR FEDERAL EMPLOYEES WHO ARE INDEBTED TO THE UNITED STATES UNDER PROGRAMS ADMINISTERED BY THE SECRETARY OF EDUCATION § 31.11 Offset process. (a) The...

Seismic Load Rating Procedure for Welded Steel Frames Oligo-cyclic Fatigue

International Nuclear Information System (INIS)

Ratiu, Mircea D.; Moisidis, Nicolae T.

2004-01-01

A dynamic load rating approach for seismic qualification of cold-formed steel welded frames is presented. Allowable seismic loads are developed from cyclic and monotonic tests of standard cold-formed steel components commonly used for piping and electrical raceway supports. The method permits simplified qualification of all connections of frame components through a single load comparison. Test input consists of rotation/cycles-to-failure data and monotonic moment/rotation data. Cyclic data are statistically evaluated to determine an acceptable maximum seismic rotation for the connection. The allowable seismic load is determined from the corresponding static rotation. Application to seismic qualification procedures is discussed. (authors)

Attention-dependent sound offset-related brain potentials.

Science.gov (United States)

Horváth, János

2016-05-01

When performing sensory tasks, knowing the potentially occurring goal-relevant and irrelevant stimulus events allows the establishment of selective attention sets, which result in enhanced sensory processing of goal-relevant events. In the auditory modality, such enhancements are reflected in the increased amplitude of the N1 ERP elicited by the onsets of task-relevant sounds. It has been recently suggested that ERPs to task-relevant sound offsets are similarly enhanced in a tone-focused state in comparison to a distracted one. The goal of the present study was to explore the influence of attention on ERPs elicited by sound offsets. ERPs elicited by tones in a duration-discrimination task were compared to ERPs elicited by the same tones in not-tone-focused attentional setting. Tone offsets elicited a consistent, attention-dependent biphasic (positive-negative--P1-N1) ERP waveform for tone durations ranging from 150 to 450 ms. The evidence, however, did not support the notion that the offset-related ERPs reflected an offset-specific attention set: The offset-related ERPs elicited in a duration-discrimination condition (in which offsets were task relevant) did not significantly differ from those elicited in a pitch-discrimination condition (in which the offsets were task irrelevant). Although an N2 reflecting the processing of offsets in task-related terms contributed to the observed waveform, this contribution was separable from the offset-related P1 and N1. The results demonstrate that when tones are attended, offset-related ERPs may substantially overlap endogenous ERP activity in the postoffset interval irrespective of tone duration, and attention differences may cause ERP differences in such postoffset intervals. © 2016 Society for Psychophysiological Research.

Co-Seismic Mass Dislocation and its Effect on Earth's Rotation and Gravity

Science.gov (United States)

Chao, B. F.; Gross, R. S.

2002-01-01

Mantle processes often involve large-scale mass transport, ranging from mantle convection, tectonic motions, glacial isostatic adjustment, to tides, atmospheric and oceanic loadings, volcanism and seismicity. On very short time scale of less than an hour, co-seismic event, apart from the shaking that is the earthquake, leaves behind permanent (step-function-like) dislocations in the crust and mantle. This redistribution of mass changes the Earth's inertia tensor (and hence Earth's rotation in both length-of-day and polar motion), and the gravity field (in terms of spherical harmonic Stokes coefficients). The question is whether these effects are large enough to be of any significance. In this paper we report updated calculation results based on Chao & Gross (1987). The calculation uses the normal mode summation scheme, applied to nearly twenty thousand major earthquakes that occurred during 1976-2002, according to source mechanism solutions given by the Harvard Central Moment Tensor catalog. Compared to the truly large ones earlier in the century, the earthquakes we study are individually all too small to have left any discernible signature in geodetic records of Earth rotation or global gravity field. However, their collective effects continue to exhibit an extremely strong statistical tendencies. For example, earthquakes conspire to decrease J2 and J22 while shortening LOD, resulting in a rounder and more compact Earth. Strong tendency is also seen in the earthquakes trying to nudge the Earth rotation pole towards approximately 140 degrees E, roughly opposite to the observed polar drift direction. The geophysical significance and implications will be further studied.

Propagation of Exploration Seismic Sources in Shallow Water

Science.gov (United States)

Diebold, J. B.; Tolstoy, M.; Barton, P. J.; Gulick, S. P.

2006-05-01

The choice of safety radii to mitigation the impact of exploration seismic sources upon marine mammals is typically based on measurement or modeling in deep water. In shallow water environments, rule-of-thumb spreading laws are often used to predict the falloff of amplitude with offset from the source, but actual measurements (or ideally, near-perfect modeling) are still needed to account for the effects of bathymetric changes and subseafloor characteristics. In addition, the question: "how shallow is 'shallow?'" needs an answer. In a cooperative effort by NSF, MMS, NRL, IAGC and L-DEO, a series of seismic source calibration studies was carried out in the Northern Gulf of Mexico during 2003. The sources used were the two-, six-, ten-, twelve-, and twenty-airgun arrays of R/V Ewing, and a 31-element, 3-string "G" gun array, deployed by M/V Kondor, an exploration industry source ship. The results of the Ewing calibrations have been published, documenting results in deep (3200m) and shallow (60m) water. Lengthy analysis of the Kondor results, presented here, suggests an approach to answering the "how shallow is shallow" question. After initially falling off steadily with source-receiver offset, the Kondor levels suddenly increased at a 4km offset. Ray-based modeling with a complex, realistic source, but with a simple homogeneous water column-over-elastic halfspace ocean shows that the observed pattern is chiefly due to geophysical effects, and not focusing within the water column. The same kind of modeling can be used to predict how the amplitudes will change with decreasing water depth, and when deep-water safety radii may need to be increased. Another set of data (see Barton, et al., this session) recorded in 20 meters of water during early 2005, however, shows that simple modeling may be insufficient when the geophysics becomes more complex. In this particular case, the fact that the seafloor was within the near field of the R/V Ewing source array seems to have

Offsets - An opportunity of Financing

International Nuclear Information System (INIS)

PRIN, Coralie

2008-01-01

Nuclear Research Reactors sometimes need to implement projects to upgrade, revamp or convert their reactor, acquire new fuel elements, etc. However, as their activities are mainly of noncommercial nature, they sometimes lack of financial resources to implement these projects by themselves. Several solutions exist: loans, governmental budget, subsidies from international organizations (IAEA). Offsets are another source of financing. They also are free of charge for the reactor. The objective of offsets is to Identify, implement and finance projects that: directly create or sustain a local economic activity of high-added value, would not have happened without the Obligor's intervention, and are of crucial importance given the country's political background (favor employment, technology transfers, training and education, research and development, etc.). Companies worldwide are willing to finance local projects to fulfill their Offset Obligation. Local organizations or institutions are willing to invest to increase their activities but lack of financial resources. Offset regulations are an opportunity on both sides and are free for the local organization. The monetary value of an Offset obligation is calculated as a percentage of the main contract price (or as a percentage of the imported part value). That percentage depends on the Country's legislation and on the nature of the main contract (defense or civilian). This value has to be compensated by an equivalent economic value (a Project's cost is different from its value). There is two ways of assessing a value: - Political aspects: The Project is of political importance for the country (development of an export capability, technology and/or know-how transfers) and the project in line with the country's political priorities (employment, research, international presence, etc.). - Economic benefits: the project directly sustains or creates additional activities, turnover, R and D, employment, etc. It benefits directly

Joint channel/frequency offset estimation and correction for coherent optical FBMC/OQAM system

Science.gov (United States)

Wang, Daobin; Yuan, Lihua; Lei, Jingli; wu, Gang; Li, Suoping; Ding, Runqi; Wang, Dongye

2017-12-01

In this paper, we focus on analysis of the preamble-based joint estimation for channel and laser-frequency offset (LFO) in coherent optical filter bank multicarrier systems with offset quadrature amplitude modulation (CO-FBMC/OQAM). In order to reduce the noise impact on the estimation accuracy, we proposed an estimation method based on inter-frame averaging. This method averages the cross-correlation function of real-valued pilots within multiple FBMC frames. The laser-frequency offset is estimated according to the phase of this average. After correcting LFO, the final channel response is also acquired by averaging channel estimation results within multiple frames. The principle of the proposed method is analyzed theoretically, and the preamble structure is thoroughly designed and optimized to suppress the impact of inherent imaginary interference (IMI). The effectiveness of our method is demonstrated numerically using different fiber and LFO values. The obtained results show that the proposed method can improve transmission performance significantly.

Use of walk through procedures to minimize seismic upgrade for nuclear facilities

International Nuclear Information System (INIS)

Djordjevic, W.

1985-01-01

The seismic evaluation Walk Through Procedure briefly described in this paper can be used to dramatically reduce seismic evaluation efforts. The procedure makes maximum use of existing extensive generic data bases which define seismic fragility or ruggedness while at the same time utilize component and site specific field inspections of each component and its environs. It is recommended that the Walk Through procedure outlined herein be considered as a primary method of evaluating the seismic capabilities of nuclear facilities in the future. 7 references, 4 figures

Seismic activity in northeastern Brazill-new perspectives

Science.gov (United States)

Ferreira, J. M.; Do Nascimento, A. F.; Vilar, C. S.; Bezerra, F. H.; Assumpcao, M.; Berrocal, J.; Fuck, R. A.

2007-05-01

Northeastern Brazil is the most seismic active region in the country. Some earthquakes with magnitude above 5.0 and intensity VII MM associated with swam-like seismic activity lasting for many years are a serious social concern. Since the 1980's macroseismic and instrumental surveys have been carried out in this region and they are an important data archive which allows the composition of a reliable catalogue of seismic activity for this region. Among the many scientific results it was possible to identify the main seismogenic areas, obtain reliable hypocentres and focal mechanisms. As a consequence, it was possible also to analyse the relationship between seismicity and geological features. It was also possible to determined maximum horizontal stress direction for the region. An important induced seismic activity case has also been reported in the area as being a classical example of pore pressure diffusion triggering mechanism. The majority of the results were obtained using analogic data. Recently, a new research project is being conducted and will allow us to provide a regional scale monitoring with 6 broad-band stations and a new portable six station digital seismic network equipped with short- period sensors. Thus, with the continuous seismic activity in the area we trust that the results of this project will increase the present knowledge of seismic activity in northeastern Brazil.

The effect of intra-trappean heterogeneities on seismic data: A case study from the Deccan Traps

Science.gov (United States)

Pandey, Dhananjai; Singh, Satish; Sinha, Martin; MacGregor, Lucy

2007-09-01

Hydrocarbon exploration interests have renewed the need for developing new sub basalt imaging techniques. One of the most important problems encountered today is seismic imaging below basalt. In recent years, this problem appears to have been overcome partly by using long offset seismic data. However near offset data are yet to be fully utilised due to the complex waveform caused by the surface as well as internal heterogeneity of the basalts. The near normal incidence data, which influence the sub-basalt imaging, are highly useful to understand the internal structure within a basalt layer. The use of converted waves for such targets has been proposed as an alternative in a rather homogeneous basalt layer. With a few synthetic modelling exercises here we highlight the practical difficulties in dealing with more realistic and heterogeneous basalt flow. Full waveform seismograms are computed to understand the effects of intra-trappean sediments on the seismic data. A case study from the Deccan Traps of India is presented in this paper. First, we discuss the effects of intercalated sediments on the overall seismic image. Later, the sonic log data from the field are used to compute the full wave-field response using the reflectivity method and compared with the field data. The feasibility of using mode converted waves (P to S and vice-versa at the top and bottom basalt interfaces) for sub-basalt imaging in Kutch region is discussed through a series of velocity-depth profiles. By comparing with the field data we demonstrate that the effects of multiple thin layering within the basalt can strongly deteriorate the image we seek to interpret and exploit.

Co-seismic luminescence in Lima, 150 km from the epicenter of the Pisco, Peru earthquake of 15 August 2007

Directory of Open Access Journals (Sweden)

J. A. Heraud

2011-04-01

Full Text Available The first photographs of Co-seismic Luminescence, commonly known as Earthquake lights (EQLs, were reported in 1968 in Japan. However, there have been documented reports of luminescence associated with earthquakes since ancient times in different parts of the world. Besides this, there is modern scientific work dealing with evidence of and models for the production of such lights. During the Peru 15 August 2007 M_w=8.0 earthquake which occurred at 06:40 p.m. LT, hence dark in the southern wintertime, several EQLs were observed along the Peruvian coast and extensively reported in the capital city of Lima, about 150 km northwest of the epicenter. These lights were video-recorded by a security camera installed at the Pontificia Universidad Catolica del Peru (PUCP campus and time-correlated with seismic ground accelerations registered at the seismological station on campus, analyzed and related to highly qualified eyewitness observations of the phenomena from other parts of the city and to other video recordings. We believe the evidence presented here contributes significantly to sustain the hypothesis that electromagnetic phenomena related to seismic activity can occur, at least during an earthquake. It is highly probable that continued research in luminescence and the use of magnetometers in studying electromagnetic activity and radon gas emanation detectors will contribute even more towards determining their occurrence during and probably prior to seismic activity.

Seismic Device UVS 1504, possibilities of its Utilization

Directory of Open Access Journals (Sweden)

Leššo Igor

1996-09-01

Full Text Available Department of Mining and Geotechnics for many years deals with questions of the technical seismicity. In the paper are given possibilities of utilizing the UVS 1504 device and results obtained from the measurement of seismic effects of blasting as well as others sources of bursts. The measurements showed that this device enables to measure parameters and to evaluate measured data quickly, reliably, and with a very high precision. The device enables evaluating individual time degrees of blasts, determining the law of attenuation of the seismic waves, and precise determination of the maximum charge permissible for futher advance of the blasting in given conditions.

MULTI-ATTRIBUTE SEISMIC/ROCK PHYSICS APPROACH TO CHARACTERIZING FRACTURED RESERVOIRS

Energy Technology Data Exchange (ETDEWEB)

Gary Mavko

2000-10-01

This project consists of three key interrelated Phases, each focusing on the central issue of imaging and quantifying fractured reservoirs, through improved integration of the principles of rock physics, geology, and seismic wave propagation. This report summarizes the results of Phase I of the project. The key to successful development of low permeability reservoirs lies in reliably characterizing fractures. Fractures play a crucial role in controlling almost all of the fluid transport in tight reservoirs. Current seismic methods to characterize fractures depend on various anisotropic wave propagation signatures that can arise from aligned fractures. We are pursuing an integrated study that relates to high-resolution seismic images of natural fractures to the rock parameters that control the storage and mobility of fluids. Our goal is to go beyond the current state-of-the art to develop and demonstrate next generation methodologies for detecting and quantitatively characterizing fracture zones using seismic measurements. Our study incorporates 3 key elements: (1) Theoretical rock physics studies of the anisotropic viscoelastic signatures of fractured rocks, including up scaling analysis and rock-fluid interactions to define the factors relating fractures in the lab and in the field. (2) Modeling of optimal seismic attributes, including offset and azimuth dependence of travel time, amplitude, impedance and spectral signatures of anisotropic fractured rocks. We will quantify the information content of combinations of seismic attributes, and the impact of multi-attribute analyses in reducing uncertainty in fracture interpretations. (3) Integration and interpretation of seismic, well log, and laboratory data, incorporating field geologic fracture characterization and the theoretical results of items 1 and 2 above. The focal point for this project is the demonstration of these methodologies in the Marathon Oil Company Yates Field in West Texas.

MIGRATIONS OF RELEASED SEISMIC ENERGY IN VARIOUS GEODYNAMIC CONDITIONS

Directory of Open Access Journals (Sweden)

A. V. Novopashina

2018-01-01

Full Text Available The properties of slow seismic activity migration have been revealed by the space-time analysis of the total earthquake energy (LgEsum. Our study of seismic activity covers the fragments of  the Central Asian, Pacific and Alpine seismic belts: the Baikal rift system (BRS, Russia, the San Andreas fault zone (California, USA, the Christchurch fault (New Zealand, the North and East Anatolian faults (Turkey, the Philippine subduction zone, and the central fragment of the Mid-Atlantic oceanic ridge. The chains of LgEsum clusters mark the propagation of the maximum stresses front in the weaker crust areas, the zones of fault dynamic influence, and the regions of conjugated tectonic structures. The migration process is characterized by a periodicity, changes in direction, and similar modular values of the migration rates within a single fault segment (or a fault zone, which is probably related to the mechanical and rheological crust and upper mantle properties. The data analysis shows that a strong earthquake source may occur at a location wherein the front of seismic activity propagates with periodical changes in direction, and such a source can develop within a period that is multiple of the migration fluctuations, probably associated with the influence of external periodic factors. The main periods of migration fluctuations (2–4 years, and 9–13 years, in different ratios are present in the seismic regimes of different seismic belts. The migration rate, as well as the propagation velocity of the maximum stresses front, directly depends on the velocity of movements between the plates in the region.

41 CFR 105-56.019 - Offset amount.

Science.gov (United States)

2010-07-01

... Administration 56-SALARY OFFSET FOR INDEBTEDNESS OF FEDERAL EMPLOYEES TO THE UNITED STATES Centralized Salary... referred for offset under this subpart is $100. (b) The amount offset from a salary payment under this... resolved to the satisfaction of GSA. ...

Investing carbon offsets in woody forests - the best solution for California?

Science.gov (United States)

Dass, P.; Houlton, B. Z.; Warlind, D.

2016-12-01

Increasing atmospheric carbon dioxide (CO2) concentrations from fossil fuel combustion, land conversion and biomass burning are principal to climate change and its manifolds risks on human health, the environment and the global economy. Effective mitigation of climate change thereby involves cutting fossil-fuel emissions at the source or capturing CO2 in engineered or natural ecosystem stocks, or both. The lifetime of CO2 in the atmosphere exceeds 100 years; thus, in the case of CO2 sequestration by natural ecosystems, the residence time of soil and vegetation carbon(C) is a critical component of the efficacy of C offsets in the marketplace, particularly in local to global Cap and Trade frameworks. Here we use a land-surface model to analyze trade-offs in C investment into natural forest vs. grassland sinks and the role of fire in driving the most sustained pathways of CO2 sequestration under Cap and Trade policies. We focus on the California Climate Exchange and AB32 as the model system for examining risks of CO2 offset investments by considering model-based scenarios of (a.) natural woody forests (mixture of trees, shrubs and grasslands) or (b.) pure grasslands (no woody vegetation allowed) under conditions of drought and changes in fire frequency. While forests capture more carbon than grasslands, the latter stores a greater fraction of C in below ground stocks, making it less vulnerable to climate-driven disturbances. Preliminary results for simulations carried out for the last century for the state of California corroborate this hypothesis: while trees capture 100 GgCyr-1 more than grasses, CO2 emissions due to fire is less by 20 GgCyr-1 from grasslands when compared to forest environments. Since policies need to regard potential future scenarios, we present results that investigate how the alternate systems of trees and grasses respond to (i.) the environmental conditions of the no-mitigation scenario (RCP 8.5) through the year 2100, (ii.) periods of extended

Early arrival waveform inversion of shallow seismic land data

KAUST Repository

Hanafy, Sherif M.

2013-09-22

We estimate the near-surface velocity distribution over Wadi Qudaid in Saudi Arabia by applying early arrival waveform inversion (EWI) to shallow seismic land data collected with source-receiver offsets no longer than 232 m. The main purpose is to characterize the shallow subsurface for its water storage and reuse potential. To enhance the accuracy of EWI, we extracted a natural source wavelet from the data, and also corrected for the attenuation effects with an estimated factor Q. Results suggest that, compared to traveltime tomography, EWI can generate a highly resolved velocity tomogram from shallow seismic data. The more accurate EWI tomogram can make an economically important difference in assessing the storage potential of this wadi; in this case we find an increase of 18% of storage potential in the EWI tomogram relative to the traveltime tomogram. This approach suggests that FWI might be a more accurate means for economically characterizing the water storage potential for wadis’ throughout the world.

Investigating the temporal variations of the time-clustering behavior of the Koyna-Warna (India) reservoir-triggered seismicity

International Nuclear Information System (INIS)

Telesca, Luciano

2011-01-01

Research highlights: → Time-clustering behaviour in seismicity can be detected by applying the Allan Factor. → The reservoir-induced seismicity at Koyna-Warna (India) is time-clusterized. → Pre- and co-seismic increases of the time-clustering degree are revealed. - Abstract: The time-clustering behavior of the 1996-2005 seismicity of Koyna-Warna region (India), a unique site where reservoir-triggered earthquakes have been continuously occurring over the last about 50 year, has been analyzed. The scaling exponent α, estimated by using the Allan Factor method, a powerful tool to investigate clusterization in point processes, shows co-seismic and pre-seismic enhancements associated with the occurrence of the major events.

Measuring snow water equivalent from common-offset GPR records through migration velocity analysis

Science.gov (United States)

St. Clair, James; Holbrook, W. Steven

2017-12-01

Many mountainous regions depend on seasonal snowfall for their water resources. Current methods of predicting the availability of water resources rely on long-term relationships between stream discharge and snowpack monitoring at isolated locations, which are less reliable during abnormal snow years. Ground-penetrating radar (GPR) has been shown to be an effective tool for measuring snow water equivalent (SWE) because of the close relationship between snow density and radar velocity. However, the standard methods of measuring radar velocity can be time-consuming. Here we apply a migration focusing method originally developed for extracting velocity information from diffracted energy observed in zero-offset seismic sections to the problem of estimating radar velocities in seasonal snow from common-offset GPR data. Diffractions are isolated by plane-wave-destruction (PWD) filtering and the optimal migration velocity is chosen based on the varimax norm of the migrated image. We then use the radar velocity to estimate snow density, depth, and SWE. The GPR-derived SWE estimates are within 6 % of manual SWE measurements when the GPR antenna is coupled to the snow surface and 3-21 % of the manual measurements when the antenna is mounted on the front of a snowmobile ˜ 0.5 m above the snow surface.

41 CFR 105-56.029 - Offset amount.

Science.gov (United States)

2010-07-01

... Administration 56-SALARY OFFSET FOR INDEBTEDNESS OF FEDERAL EMPLOYEES TO THE UNITED STATES Centralized Salary... salary offset under this subpart is $100. (b) The amount offset from a salary payment under this subpart... otherwise resolved to the satisfaction of the creditor agency. ...

A Robust Approach for Clock Offset Estimation in Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Kim Jang-Sub

2010-01-01

Full Text Available The maximum likelihood estimators (MLEs for the clock phase offset assuming a two-way message exchange mechanism between the nodes of a wireless sensor network were recently derived assuming Gaussian and exponential network delays. However, the MLE performs poorly in the presence of non-Gaussian or nonexponential network delay distributions. Currently, there is a need to develop clock synchronization algorithms that are robust to the distribution of network delays. This paper proposes a clock offset estimator based on the composite particle filter (CPF to cope with the possible asymmetries and non-Gaussianity of the network delay distributions. Also, a variant of the CPF approach based on the bootstrap sampling (BS is shown to exhibit good performance in the presence of reduced number of observations. Computer simulations illustrate that the basic CPF and its BS-based variant present superior performance than MLE under general random network delay distributions such as asymmetric Gaussian, exponential, Gamma, Weibull as well as various mixtures.

Site response assessment using borehole seismic records

Energy Technology Data Exchange (ETDEWEB)

Park, Donghee; Chang, Chunjoong; Choi, Weonhack [KHNP Central Research Institute, Daejeon (Korea, Republic of)

2014-05-15

In regions with high seismic activity, such as Japan, the Western United States and Taiwan, borehole seismometers installed deep underground are used to monitor seismic activity during the course of seismic wave propagation at various depths and to study the stress changes due to earthquakes and analyze the connection to fault movements. The Korea Meteorological Administration (KMA) and the Korea Institute of Geology and Mining (KIGAM) have installed and are operating borehole seismometers at a depth of 70∼100 meters for the precise determination of epicenters. Also, Korea Hydro and Nuclear Power Co., Ltd. (KHNP) has installed and is operating 2 borehole seismic stations near Weolseong area to observe at a depth of 140 meters seismic activities connected to fault activity. KHNP plans to operate in the second half of 2014 a borehole seismic station for depths less than 300 and 600 meters in order to study the seismic response characteristics in deep strata. As a basic study for analyzing ground motion response characteristics at depths of about 300 to 600 meters in connection with the deep geological disposal of spent nuclear fuel, the present study examined the background noise response characteristics of the borehole seismic station operated by KHNP. In order to analyze the depth-dependent impact of seismic waves at deeper depths than in Korea, seismic data collected by Japan's KIK-net seismic stations were used and the seismic wave characteristics analyzed by size and depth. In order to analyze the borehole seismic observation data from the seismic station operated by KHNP, this study analyzed the background noise characteristics by using a probability density function.

Site response assessment using borehole seismic records

International Nuclear Information System (INIS)

Park, Donghee; Chang, Chunjoong; Choi, Weonhack

2014-01-01

In regions with high seismic activity, such as Japan, the Western United States and Taiwan, borehole seismometers installed deep underground are used to monitor seismic activity during the course of seismic wave propagation at various depths and to study the stress changes due to earthquakes and analyze the connection to fault movements. The Korea Meteorological Administration (KMA) and the Korea Institute of Geology and Mining (KIGAM) have installed and are operating borehole seismometers at a depth of 70∼100 meters for the precise determination of epicenters. Also, Korea Hydro and Nuclear Power Co., Ltd. (KHNP) has installed and is operating 2 borehole seismic stations near Weolseong area to observe at a depth of 140 meters seismic activities connected to fault activity. KHNP plans to operate in the second half of 2014 a borehole seismic station for depths less than 300 and 600 meters in order to study the seismic response characteristics in deep strata. As a basic study for analyzing ground motion response characteristics at depths of about 300 to 600 meters in connection with the deep geological disposal of spent nuclear fuel, the present study examined the background noise response characteristics of the borehole seismic station operated by KHNP. In order to analyze the depth-dependent impact of seismic waves at deeper depths than in Korea, seismic data collected by Japan's KIK-net seismic stations were used and the seismic wave characteristics analyzed by size and depth. In order to analyze the borehole seismic observation data from the seismic station operated by KHNP, this study analyzed the background noise characteristics by using a probability density function

From Geodetic Imaging of Seismic and Aseismic Fault Slip to Dynamic Modeling of the Seismic Cycle

Science.gov (United States)

Avouac, Jean-Philippe

2015-05-01

Understanding the partitioning of seismic and aseismic fault slip is central to seismotectonics as it ultimately determines the seismic potential of faults. Thanks to advances in tectonic geodesy, it is now possible to develop kinematic models of the spatiotemporal evolution of slip over the seismic cycle and to determine the budget of seismic and aseismic slip. Studies of subduction zones and continental faults have shown that aseismic creep is common and sometimes prevalent within the seismogenic depth range. Interseismic coupling is generally observed to be spatially heterogeneous, defining locked patches of stress accumulation, to be released in future earthquakes or aseismic transients, surrounded by creeping areas. Clay-rich tectonites, high temperature, and elevated pore-fluid pressure seem to be key factors promoting aseismic creep. The generally logarithmic time evolution of afterslip is a distinctive feature of creeping faults that suggests a logarithmic dependency of fault friction on slip rate, as observed in laboratory friction experiments. Most faults can be considered to be paved with interlaced patches where the friction law is either rate-strengthening, inhibiting seismic rupture propagation, or rate-weakening, allowing for earthquake nucleation. The rate-weakening patches act as asperities on which stress builds up in the interseismic period; they might rupture collectively in a variety of ways. The pattern of interseismic coupling can help constrain the return period of the maximum- magnitude earthquake based on the requirement that seismic and aseismic slip sum to match long-term slip. Dynamic models of the seismic cycle based on this conceptual model can be tuned to reproduce geodetic and seismological observations. The promise and pitfalls of using such models to assess seismic hazard are discussed.

5 CFR 1639.27 - Procedures for salary offset.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Procedures for salary offset. 1639.27... Salary Offset § 1639.27 Procedures for salary offset. (a) The Board will coordinate salary deductions... pay and will implement the salary offset. (c) Deductions will begin within three official pay periods...

Development of a Fiber-Optics Microspatially Offset Raman Spectroscopy Sensor for Probing Layered Materials.

Science.gov (United States)

Vandenabeele, Peter; Conti, Claudia; Rousaki, Anastasia; Moens, Luc; Realini, Marco; Matousek, Pavel

2017-09-05

Microspatially offset Raman spectroscopy (micro-SORS) has been proposed as a valuable approach to sample molecular information from layers that are covered by a turbid (nontransparent) layer. However, when large magnifications are involved, the approach is not straightforward, as spatial constraints exist to position the laser beam and the objective lens with the external beam delivery or, with internal beam delivery, the maximum spatial offset achievable is restricted. To overcome these limitations, we propose here a prototype of a new micro-SORS sensor, which uses bare glass fibers to transfer the laser radiation to the sample and to collect the Raman signal from a spatially offset zone to the Raman spectrometer. The concept also renders itself amenable to remote delivery and to the miniaturization of the probe head which could be beneficial for special applications, e.g., where access to sample areas is restricted. The basic applicability of this approach was demonstrated by studying several layered structure systems. Apart from proving the feasibility of the technique, also, practical aspects of the use of the prototype sensor are discussed.

Seismic interferometry of railroad induced ground motions: body and surface wave imaging

Science.gov (United States)

Quiros, Diego A.; Brown, Larry D.; Kim, Doyeon

2016-04-01

Seismic interferometry applied to 120 hr of railroad traffic recorded by an array of vertical component seismographs along a railway within the Rio Grande rift has recovered surface and body waves characteristic of the geology beneath the railway. Linear and hyperbolic arrivals are retrieved that agree with surface (Rayleigh), direct and reflected P waves observed by nearby conventional seismic surveys. Train-generated Rayleigh waves span a range of frequencies significantly higher than those recovered from typical ambient noise interferometry studies. Direct P-wave arrivals have apparent velocities appropriate for the shallow geology of the survey area. Significant reflected P-wave energy is also present at relatively large offsets. A common midpoint stack produces a reflection image consistent with nearby conventional reflection data. We suggest that for sources at the free surface (e.g. trains) increasing the aperture of the array to record wide angle reflections, in addition to longer recording intervals, might allow the recovery of deeper geological structure from railroad traffic. Frequency-wavenumber analyses of these recordings indicate that the train source is symmetrical (i.e. approaching and receding) and that deeper refracted energy is present although not evident in the time-offset domain. These results confirm that train-generated vibrations represent a practical source of high-resolution subsurface information, with particular relevance to geotechnical and environmental applications.

22 CFR 309.17 - Procedures for salary offset.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 2 2010-04-01 2010-04-01 true Procedures for salary offset. 309.17 Section 309.17 Foreign Relations PEACE CORPS DEBT COLLECTION Salary Offset § 309.17 Procedures for salary offset. Unless otherwise provided by statute or contract, the following procedures apply to salary offset: (a...

7 CFR 3.46 - Offset against tax refunds.

Science.gov (United States)

2010-01-01

... 7 Agriculture 1 2010-01-01 2010-01-01 false Offset against tax refunds. 3.46 Section 3.46 Agriculture Office of the Secretary of Agriculture DEBT MANAGEMENT Administrative Offset § 3.46 Offset against tax refunds. USDA will take action to effect administrative offset against tax refunds due to debtors...

Planning for shallow high resolution seismic surveys

CSIR Research Space (South Africa)

Fourie, CJS

2008-11-01

Full Text Available of the input wave. This information can be used in conjunction with this spreadsheet to aid the geophysicist in designing shallow high resolution seismic surveys to achieve maximum resolution and penetration. This Excel spreadsheet is available free from...

5 CFR 179.211 - Notice of salary offset.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Notice of salary offset. 179.211 Section... COLLECTION STANDARDS Salary Offset § 179.211 Notice of salary offset. (a) Upon receipt of proper... certification as the debtor, a written notice of salary offset. Such notice shall, at a minimum: (1) State that...

The RING and Seismic Network: Data Acquisition of Co-located Stations

Science.gov (United States)

Falco, L.; Avallone, A.; Cattaneo, M.; Cecere, G.; Cogliano, R.; D'Agostino, N.; D'Ambrosio, C.; D'Anastasio, E.; Selvaggi, G.

2007-12-01

The plate boundary between Africa and Eurasia represents an interesting geodynamical region characterized by a complex pattern of deformation. First-order scientific problems regarding the existence of rigid blocks within the plate boundary, the present-day activity of the Calabrian subduction zone and the modes of release of seismic deformation are still awaiting for a better understanding. To address these issues, the INGV (Istituto Nazionale Geofisica e Vulcanlogia) deployed a permanent, integrated and real-time monitoring GPS network (RING) all over Italy. RING is now constituted by about 120 stations. The CGPS sites, acquiring at 1Hz and 30s sampling rate, are integrated either with broad band or very broad band seismometers and accelerometers for an improved definition of the seismically active regions. Most of the sites are connected to the acquisition centre (located in Rome and duplicated in Grottaminarda) through a satellite system (VSAT), while the remaining sites transmit data by Internet and classical phone connections. The satellite data transmission and the integration with seismic instruments makes this network one of the most innovative CGPS networks in Europe. The heterogeneity of the installed instrumentation, the transmission types and the increasing number of stations needed a central monitoring and acquisition system. A central acquisition system has been developed in Grottaminarda in southern Italy. Regarding the seismic monitoring we chose to use the open source system Earthworm, developed by USGS, with which we store waveforms and implement automatic localization of the seismic events occurring in the area. As most of the GPS sites are acquired by means of Nanometrics satellite technology, we developed a specific software (GpsView), written in Java, to monitor the state of health of those CGPS. This software receives GPS data from NaqsServer (Nanometrics acquisition system) and outputs information about the sites (i.e. approx position

An analysis of the first-arrival times picked on the DSS and wide-angle seismic section recorded in Italy since 1968

Directory of Open Access Journals (Sweden)

R. Tondi

2004-06-01

Full Text Available We performed an analysis of refraction data recorded in Italy since 1968 in the frame of the numerous deep seismic sounding and wide-angle reflection/refraction projects. The aims of this study are to construct a parametric database including the recording geometric information relative to each profile, the phase pickings and the results of some kinematic analyses performed on the data, and to define a reference 1D velocity model for the Italian territory from all the available refraction data. As concerns the first goal, for each seismic section we picked the P-wave first-arrival-times, evaluated the uncertainties of the arrival-times pickings and determined from each travel time-offset curve the 1D velocity model. The study was performed on 419 seismic sections. Picking was carried out manually by an algorithm which includes the computation of three picking functions and the picking- error estimation. For each of the travel time-offset curves a 1D velocity model has been calculated. Actually, the 1D velocity-depth functions were estimated in three different ways which assume: a constant velocitygradient model, a varying velocity-gradient model and a layered model. As regards the second objective of this work, a mean 1D velocity model for the Italian crust was defined and compared with those used for earthquake hypocentre locations and seismic tomographic studies by different institutions operating in the Italian area, to assess the significance of the model obtained. This model can be used in future works as input for a next joint tomographic inversion of active and passive seismic data.

Induced seismicity and carbon storage: Risk assessment and mitigation strategies

Energy Technology Data Exchange (ETDEWEB)

White, Joshua A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Foxall, William [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Bachmann, Corinne [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Chiaramonte, Laura [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Daley, Thomas M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2016-01-28

Geologic carbon storage (GCS) is widely recognized as an important strategy to reduce atmospheric carbon dioxide (CO₂) emissions. Like all technologies, however, sequestration projects create a number of potential environmental and safety hazards that must be addressed. These include earthquakes—from microseismicity to large, damaging events—that can be triggered by altering pore-pressure conditions in the subsurface. To date, measured seismicity due to CO₂ injection has been limited to a few modest events, but the hazard exists and must be considered. There are important similarities between CO₂ injection and fluid injection from other applications that have induced significant events—e.g. geothermal systems, waste-fluid injection, hydrocarbon extraction, and others. There are also important distinctions among these technologies that should be considered in a discussion of seismic hazard. This report focuses on strategies for assessing and mitigating risk during each phase of a CO₂ storage project. Four key risks related to fault reactivation and induced seismicity were considered. Induced slip on faults could potentially lead to: (1) infrastructure damage, (2) a public nuisance, (3) brine-contaminated drinking water, and (4) CO₂-contaminated drinking water. These scenarios lead to different types of damage—to property, to drinking water quality, or to the public welfare. Given these four risks, this report focuses on strategies for assessing (and altering) their likelihoods of occurrence and the damage that may result. This report begins with an overview of the basic physical mechanisms behind induced seismicity. This science basis—and its gaps—is crucial because it forms the foundation for risk assessment and mitigation. Available techniques for characterizing and monitoring seismic behavior are also described. Again, this technical basis—and its limitations—must be factored into the risk

Thermo-Hydro-Micro-Mechanical 3D Modeling of a Fault Gouge During Co-seismic Slip

Science.gov (United States)

Papachristos, E.; Stefanou, I.; Sulem, J.; Donze, F. V.

2017-12-01

A coupled Thermo-Hydro-Micro-Mechanical (THMM) model based on the Discrete Elements method (DEM) is presented for studying the evolving fault gouge properties during pre- and co-seismic slip. Modeling the behavior of the fault gouge at the microscale is expected to improve our understanding on the various mechanisms that lead to slip weakening and finally control the transition from aseismic to seismic slip.The gouge is considered as a granular material of spherical particles [1]. Upon loading, the interactions between particles follow a frictional behavior and explicit dynamics. Using regular triangulation, a pore network is defined by the physical pore space between the particles. The network is saturated by a compressible fluid, and flow takes place following Stoke's equations. Particles' movement leads to pore deformation and thus to local pore pressure increase. Forces exerted from the fluid onto the particles are calculated using mid-step velocities. The fluid forces are then added to the contact forces resulting from the mechanical interactions before the next step.The same semi-implicit, two way iterative coupling is used for the heat-exchange through conduction.Simple tests have been performed to verify the model against analytical solutions and experimental results. Furthermore, the model was used to study the effect of temperature on the evolution of effective stress in the system and to highlight the role of thermal pressurization during seismic slip [2, 3].The analyses are expected to give grounds for enhancing the current state-of-the-art constitutive models regarding fault friction and shed light on the evolution of fault zone propertiesduring seismic slip.[1] Omid Dorostkar, Robert A Guyer, Paul A Johnson, Chris Marone, and Jan Carmeliet. On the role of fluids in stick-slip dynamics of saturated granular fault gouge using a coupled computational fluid dynamics-discrete element approach. Journal of Geophysical Research: Solid Earth, 122

12 CFR 1408.39 - Procedures for salary offset.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 7 2010-01-01 2010-01-01 false Procedures for salary offset. 1408.39 Section... STATES Offset Against Salary § 1408.39 Procedures for salary offset. (a) The Chairman, or designee of the... periods following the date of mailing or delivery of the Notice of Intent to Collect by Salary Offset. (c...

12 CFR 608.839 - Procedures for salary offset.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Procedures for salary offset. 608.839 Section... OWED THE UNITED STATES Offset Against Salary § 608.839 Procedures for salary offset. (a) The Chairman... Intent to Collect by Salary Offset. (c)(1) If the amount of the debt is equal to or is less than 15...

4D Joint Stratigraphic Inversion of Prestack Seismic Data: Application to the CO2 Storage Reservoir (Utsira Sand Formation at Sleipner Site Inversion stratigraphique jointe 4D de données sismiques avant sommation : application au réservoir de stockage de CO2 (Formation Utsira du site de Sleipner

Directory of Open Access Journals (Sweden)

Labat K.

2012-04-01

Full Text Available Seismic monitoring is commonly used in the oil industry to follow the evolution of reservoir properties during production. We present a methodology of time-lapse (or 4D stratigraphic inversion, which is able to provide an estimation of P- and S-wave impedance variations in the reservoir by inverting prestack time-lapse seismic data. The 4D inversion is implemented in the time domain and requires a time scaling law for each repeated seismic dataset in order to adjust the arrival times of homologous events observed in the so-called reference and monitor datasets. This operation is often referred to as the warping problem. The 4D inversion is a 3-step methodology. The first step consists in inverting each seismic vintage independently, thus providing as many P- and S-wave impedance distributions as datasets considered. The second step uses the available P-wave impedance information to solve the warping problem which is crucial to the third and final step: the joint inversion of all available seismic vintages. This 4D inversion sequence was applied to seismic datasets recorded on the Norwegian CO2 storage reservoir of Sleipner field located in the North Sea. The latter is becoming a reference industrial site for the long-term storage of carbon dioxide (CO2 in a saline aquifer, the Utsira sand formation. We focused our 4D inversion study on the 1994 and 2006 vintages acquired two years before and ten years after the beginning of CO2 injection, respectively. The warping correction resulted in a time-scaling law with a maximum pushdown effect of about 45 ms at the base of the Utsira aquifer. The joint 4D inversion results show more consistency than the single 3D inversion results: the 4D inversion notably provides P-wave impedances for the CO2 -saturated sandstones which are close to the values derived from rock physics studies. Le monitoring sismique est couramment utilisé dans l'industrie pétrolière pour suivre l'évolution des propriétés des r

Analysis of the German market for voluntary carbon offsetting; Analyse des deutschen Marktes zur freiwilligen Kompensation von Treibhausgasemissionen

Energy Technology Data Exchange (ETDEWEB)

Kind, Christian; Duwe, Sebastian; Taenzler, Dennis; Reuster, Lena [adelphi research gGmbH, Berlin (Germany); Kleemann, Max; Krebs, Jan-Marten [sustainable AG, Muenchen (Germany)

2010-12-15

In the past years the market for voluntary carbon offsetting has developed rapidly. Certificates sold on this market originate partly from the compliance market, i.e. from projects of the Clean Development Mechanism and the Joint Implementation. Mostly, however, certificates stem from projects of the voluntary carbon market. Voluntary carbon offsetting can serve as another mechanism to efficiently prevent emissions, while at the same time achieving co-benefits. Very little is known however of the exact state of the voluntary carbon market, e.g. factors like business volume, market actors, origin of certificates or the efficacy of the voluntary market. Analyses of the market on the global market for voluntary offsetting do exist (ENDS, Hamilton et al. 2007, 2008, 2009); however they do not allow any conclusions for the market situation in Germany. This study aims at closing this gap. From the end of 2009 until the beginning of 2010 adelphi and sustainable interviewed providers of offset services, intermediaries, certifiers and consumers like businesses and public institutions on their activities in the voluntary carbon offset market in Germany. (orig.)

13 CFR 120.1722 - SBA's offset rights.

Science.gov (United States)

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false SBA's offset rights. 120.1722... of SBA Secondary Market Guarantee Program for First Lien Position 504 Loan Pools § 120.1722 SBA's offset rights. SBA shall have the right to offset any amount owed by Lender to SBA, including, without...

Maximum leaf conductance driven by CO2 effects on stomatal size and density over geologic time.

Science.gov (United States)

Franks, Peter J; Beerling, David J

2009-06-23

Stomatal pores are microscopic structures on the epidermis of leaves formed by 2 specialized guard cells that control the exchange of water vapor and CO(2) between plants and the atmosphere. Stomatal size (S) and density (D) determine maximum leaf diffusive (stomatal) conductance of CO(2) (g(c(max))) to sites of assimilation. Although large variations in D observed in the fossil record have been correlated with atmospheric CO(2), the crucial significance of similarly large variations in S has been overlooked. Here, we use physical diffusion theory to explain why large changes in S necessarily accompanied the changes in D and atmospheric CO(2) over the last 400 million years. In particular, we show that high densities of small stomata are the only way to attain the highest g(cmax) values required to counter CO(2)"starvation" at low atmospheric CO(2) concentrations. This explains cycles of increasing D and decreasing S evident in the fossil history of stomata under the CO(2) impoverished atmospheres of the Permo-Carboniferous and Cenozoic glaciations. The pattern was reversed under rising atmospheric CO(2) regimes. Selection for small S was crucial for attaining high g(cmax) under falling atmospheric CO(2) and, therefore, may represent a mechanism linking CO(2) and the increasing gas-exchange capacity of land plants over geologic time.

Utilization of curve offsets in additive manufacturing

Science.gov (United States)

Haseltalab, Vahid; Yaman, Ulas; Dolen, Melik

2018-05-01

Curve offsets are utilized in different fields of engineering and science. Additive manufacturing, which lately becomes an explicit requirement in manufacturing industry, utilizes curve offsets widely. One of the necessities of offsetting is for scaling which is required if there is shrinkage after the fabrication or if the surface quality of the resulting part is unacceptable. Therefore, some post-processing is indispensable. But the major application of curve offsets in additive manufacturing processes is for generating head trajectories. In a point-wise AM process, a correct tool-path in each layer can reduce lots of costs and increase the surface quality of the fabricated parts. In this study, different curve offset generation algorithms are analyzed to show their capabilities and disadvantages through some test cases and improvements on their drawbacks are suggested.

10 CFR 1015.215 - Federal salary offset.

Science.gov (United States)

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Federal salary offset. 1015.215 Section 1015.215 Energy... Administrative Collection of Claims § 1015.215 Federal salary offset. (a) DOE may authorize Treasury to offset a Federal salary to satisfy delinquent debt in accordance with 5 U.S.C. 5514, Installment Deduction for...

Seismic re-evaluation of piping systems of heavy water plant, Kota

International Nuclear Information System (INIS)

Mishra, Rajesh; Soni, R.S.; Kushwaha, H.S.; Venkat Raj, V.

2002-05-01

Heavy Water Plant, Kota is the first indigenous heavy water plant built in India. The plant started operation in the year 1985 and it is approaching the completion of its originally stipulated design life. In view of the excellent record of plant operation for the past so many years, it has been planned to carry out various exercises for the life extension of the plant. In the first stage, evaluation of operation stresses was carried out for the process critical piping layouts and equipment, which are connected with 25 process critical nozzle locations, identified based on past history of the plant performance. Fatigue life evaluation has been carried out to fmd out the Cumulative Usage Factor, which helps in arriving at a decision regarding the life extension of the plant. The results of these exercises have been already reported separately vide BARC/200I /E/O04. In the second stage, seismic reevaluation of the plant has been carried out to assess its ability to maintain its integ:rity in case of a seismic event. The aim of this exercise is to assess the effects of the maximum probable earthquake at the plant site on the various systems and components of the plant. This exercise is further aimed at ensuring the adequacy of seismic supports to maintain the integrity of the system in case of a seismic event and to suggest some retrofitting measures, if required. Seismic re-evaluation of the piping of Heavy Water Plant, Kota has been performed taking into account the interaction effects from the connected equipment. Each layout has been qualified using the latest provisions of ASME Code Section III, Subsection ND wherein the earthquake loading has been considered as a reversing dynamic load. The maximum combined stresses for all the layouts due to pressure, weight and seismic loadings have been found to be well within the code allowable limit. Therefore, it has been concluded that during a maximum probable seismic event, the possibility of pipe rupture can be safely

Comparison of Greenhouse Gas Offset Quantification Protocols for Nitrogen Management in Dryland Wheat Cropping Systems of the Pacific Northwest

Directory of Open Access Journals (Sweden)

Tabitha T. Brown

2017-11-01

Full Text Available In the carbon market, greenhouse gas (GHG offset protocols need to ensure that emission reductions are of high quality, quantifiable, and real. Lack of consistency across protocols for quantifying emission reductions compromise the credibility of offsets generated. Thus, protocol quantification methodologies need to be periodically reviewed to ensure emission offsets are credited accurately and updated to support practical climate policy solutions. Current GHG emission offset credits generated by agricultural nitrogen (N management activities are based on reducing the annual N fertilizer application rate for a given crop without reducing yield. We performed a “road test” of agricultural N management protocols to evaluate differences among protocol components and quantify nitrous oxide (N2O emission reductions under sample projects relevant to N management in dryland, wheat-based cropping systems of the inland Pacific Northwest (iPNW. We evaluated five agricultural N management offset protocols applicable to North America: two methodologies of American Carbon Registry (ACR1 and ACR2, Verified Carbon Standard (VCS, Climate Action Reserve (CAR, and Alberta Offset Credit System (Alberta. We found that only two protocols, ACR2 and VCS, were suitable for this study, in which four sample projects were developed representing feasible N fertilizer rate reduction activities. The ACR2 and VCS protocols had identical baseline and project emission quantification methodologies resulting in identical emission reduction values. Reducing N fertilizer application rate by switching to variable rate N (sample projects 1–3 or split N application (sample project 4 management resulted in a N2O emission reduction ranging from 0.07 to 0.16, and 0.26 Mg CO2e ha−1, respectively. Across the range of C prices considered ($5, $10, and $50 per metric ton of CO2 equivalent, we concluded that the N2O emission offset payment alone ($0.35–$13.0 ha−1 was unlikely to

Quantitative estimation of lithofacies from seismic data in a tertiary turbidite system in the North Sea

Energy Technology Data Exchange (ETDEWEB)

Joerstad, A.K.; Avseth, P.Aa; Mukerji, T.; Mavko, G.; Granli, J.R.

1998-12-31

Deep water clastic systems and associated turbidite reservoirs are often characterized by very complex sand distributions and reservoir description based on conventional seismic and well-log stratigraphic analysis may be very uncertain in these depositional environments. There is shown that reservoirs in turbidite systems have been produced very inefficiently in conventional development. More than 70% of the mobile oil is commonly left behind, because of the heterogeneous nature of these reservoirs. In this study there is examined a turbidite system in the North Sea with five available wells and a 3-D seismic near and far offset stack to establish most likely estimates of facies and pore fluid within the cube. 5 figs.

Traveltime and waveform tomography analysis of synthetic borehole seismic data based on the CO2SINK project site, Germany

Science.gov (United States)

Yang, Can; Fan, Wenfang; Juhlin, Christopher

2010-05-01

Time lapse analysis of seismic data is very important for CO2 storage projects. Therefore, we have tested traveltime and waveform tomography methods to detect velocity changes in a CO2 injection reservoir using synthetic time lapse data. The structural model tested is based on the CO2SINK injection site at Ketzin, Germany where CO2 is being injected at about 630-650 m into a saline aquifer. First, we created synthetic time lapse moving source profiling (MSP) data, also known as walkaway profiling. The velocity model used for modeling was based on well logging and lithological information in the injection borehole. Gassmann fluid substitution was used to calculate the reservoir velocity after injection. In this substitution, we assumed a saturation of CO2 of 30%. The model velocity of the reservoir changed from 2750 m/s (before injection) to 2150 m/s (after injection). A 2D finite difference code available in Seismic Unix (www.cwp.mines.edu) was used. 60 source points were distributed along a surface line. The distance from the injection well was between 150m and 858m, with an interval of 12m. We recorded 21 channels at receiver depths from 470m to 670m, with an interval of 10m. The injection layer was assumed to be between 629m and 650m depth. The wavelet used for the synthetic data was a Gaussian derivative with an average frequency of 60Hz. Then first arrivals were picked on both data sets and used as input data for traveltime tomography. For traveltime tomography, the PS_tomo program was used. Since no data were recorded above 470m, the initial velocity model used above this depth was the true velocity model. Below 470m, the initial velocity model increases linearly from 3000m/s to 3250m/s. After inversion, the reservoir velocity and an anhydrite layer (high velocity layer) can be seen clearly in the final inverted velocity models. Using these velocity models as starting models, we performed waveform tomography in the frequency domain using a program supplied by

Broadband Seismic Studies at the Mallik Gas Hydrate Research Well

Science.gov (United States)

Sun, L. F.; Huang, J.; Lyons-Thomas, P.; Qian, W.; Milkereit, B.; Schmitt, D. R.

2005-12-01

The JAPEX/JNOC/GSC et al. Mallik 3L-38, 4L-38 and 5L-38 scientific wells were drilled in the MacKenzie Delta, NWT, Canada in early 2002 primarily for carrying out initial tests of the feasibility of producing methane gas from the large gas hydrate deposits there [1]. As part of this study, high resolution seismic profiles, a pseudo-3D single fold seismic volume and broadband (8~180Hz) multi-offset vertical seismic profiles (VSP) were acquired at the Mallik site. Here, we provide details on the acquisition program, present the results of the 2D field profile, and discuss the potential implications of these observations for the structure of the permafrost and gas hydrate zones. These zones have long been problematic in seismic imaging due to the lateral heterogeneities. Conventional seismic data processing usually assume a stratified, weak-contrast elastic earth model. However, in permafrost and gas hydrate zones this approximation often becomes invalid. This leads to seismic wave scattering caused by multi-scale perturbation of elastic properties. A 3D viscoelastic finite difference modeling algorithm was employed to simulate wave propagation in a medium with strong contrast. Parameters in this modeling analysis are based on the borehole geophysical log data. In addition, an uncorrelated Vibroseis VSP data set was studied to investigate frequency-dependent absorption and velocity dispersion. Our results indicate that scattering and velocity dispersion are important for a better understanding of attenuation mechanisms in heterogeneous permafrost and gas hydrate zones. [1] Dallimore, S.R., Collett, T.S., Uchida, T., and Weber, M., 2005, Overview of the science program for the Mallik 2002 Gas Hydrate Production Research Well Program; in Scientific Results from Mallik 2002 Gas Hydrate production Research Well Program, MacKenzie Delta, Northwest Territories, Canada, (ed.) S.R. Dallimore and T.S. Collett; Geological Survey of Canada, Bulletin 585, in press.

Seismic hazard in the Nation's breadbasket

Science.gov (United States)

Boyd, Oliver; Haller, Kathleen; Luco, Nicolas; Moschetti, Morgan P.; Mueller, Charles; Petersen, Mark D.; Rezaeian, Sanaz; Rubinstein, Justin L.

2015-01-01

The USGS National Seismic Hazard Maps were updated in 2014 and included several important changes for the central United States (CUS). Background seismicity sources were improved using a new moment-magnitude-based catalog; a new adaptive, nearest-neighbor smoothing kernel was implemented; and maximum magnitudes for background sources were updated. Areal source zones developed by the Central and Eastern United States Seismic Source Characterization for Nuclear Facilities project were simplified and adopted. The weighting scheme for ground motion models was updated, giving more weight to models with a faster attenuation with distance compared to the previous maps. Overall, hazard changes (2% probability of exceedance in 50 years, across a range of ground-motion frequencies) were smaller than 10% in most of the CUS relative to the 2008 USGS maps despite new ground motion models and their assigned logic tree weights that reduced the probabilistic ground motions by 5–20%.

Variable post-Paleozoic deformation detected by seismic reflection profiling across the northwestern "prong" of New Madrid seismic zone

Science.gov (United States)

McBride, J.H.; Pugin, Andre J.M.; Nelson, W.J.; Larson, T.H.; Sargent, S.L.; Devera, J.A.; Denny, F.B.; Woolery, E.W.

2003-01-01

High-resolution shallow seismic reflection profiles across the northwesternmost part of the New Madrid seismic zone (NMSZ) and northwestern margin of the Reelfoot rift, near the confluence of the Ohio and Mississippi Rivers in the northern Mississippi embayment, reveal intense structural deformation that apparently took place during the late Paleozoic and/or Mesozoic up to near the end of the Cretaceous Period. The seismic profiles were sited on both sides of the northeast-trending Olmsted fault, defined by varying elevations of the top of Mississippian (locally base of Cretaceous) bedrock. The trend of this fault is close to and parallel with an unusually straight segment of the Ohio River and is approximately on trend with the westernmost of two groups of northeast-aligned epicenters ("prongs") in the NMSZ. Initially suspected on the basis of pre-existing borehole data, the deformation along the fault has been confirmed by four seismic reflection profiles, combined with some new information from drilling. The new data reveal (1) many high-angle normal and reverse faults expressed as narrow grabens and anticlines (suggesting both extensional and compressional regimes) that involved the largest displacements during the late Cretaceous (McNairy); (2) a different style of deformation involving probably more horizontal displacements (i.e., thrusting) that occurred at the end of this phase near the end of McNairy deposition, with some fault offsets of Paleocene and younger units; (3) zones of steeply dipping faults that bound chaotic blocks similar to that observed previously from the nearby Commerce geophysical lineament (CGL); and (4) complex internal deformation stratigraphically restricted to the McNairy, suggestive of major sediment liquefaction or landsliding. Our results thus confirm the prevalence of complex Cretaceous deformations continuing up into Tertiary strata near the northern terminus of the NMSZ. ?? 2003 Elsevier Science B.V. All rights reserved.

Multi-Attribute Seismic/Rock Physics Approach to Characterizing Fractured Reservoirs

Energy Technology Data Exchange (ETDEWEB)

Gary Mavko

2004-11-30

fracturing is likely to be more intense near faults--sometimes referred to as the damaged zone. Yet another constraint, based on world-wide observations, is that the maximum likely fracture density increases with depth in a well-defined way. Defining these prior constrains has several benefits: they lead to a priori probability distributions of fractures, that are important for objective statistical integration; they limit the number of geologic hypotheses that need to be theoretically modeled; they provide plausible models for fracture distributions below the seismic resolution. The second element was theoretical rock physics modeling of optimal seismic attributes, including offset and azimuth dependence of traveltime, amplitude, and impedance signatures of anisotropic fractured rocks. The suggested workflow is to begin with an elastic earth model, based on well logs, theoretically add fractures to the likely facies as defined by the geologic prior information, and then compute synthetic seismic traces and attributes, including variations in P and S-wave velocities, Poisson's ratio, reflectivity, travel time, attenuation, and anisotropies of these parameters. This workflow is done in a Monte-Carlo fashion, yielding ranges of expected fracture signatures, and allowing realistic assessments of uncertainty to be honored. The third element was statistical integration of the geophysical data and prior constraints to map fracture intensity and orientations, along with uncertainties. A Bayesian framework was developed that allowed systematic integration of the prior constraints, the theoretical relations between fractures and their seismic signatures, and the various observed seismic observations. The integration scheme was successfully applied on an East Texas field site. The primary benefit from the study was the optimization and refinement of practical workflows for improved geophysical characterization of natural fractures and for quantifying the uncertainty of these

Complex Channel Avulsion in the Meghna River Foodplain During the Mid to Late Holocene: The Potential Effect of Tectonic and Co-Seismic Uplift

Science.gov (United States)

Dunham, A.; Grall, C.; Mondal, D. R.; Steckler, M. S.; Rajapara, H.; Kumar, B.; Philibosian, B.; Akhter, S. H.; Singhvi, A. K.

2016-12-01

Channel migrations and river avulsions in deltaic river systems are mainly driven by differential changes of surface topography, such as the superelevation of channels due to sedimentation. In addition to such autocyclic processes, tectonic events, such as earthquakes, may also lead to avulsions from sudden uplift. The eastern part of the Ganges-Brahmaputra-Meghna Delta (GBMD) is underlain by the blind megathrust of the IndoBurma subduction zone. In this region we investigate a 100 km long sinuous abandoned channel of the Meghna River. Immediately south of the channel, it has been previously shown that the topography is slightly higher than on the rest of the Delta and there is an oxidized Holocene exposure surface. Part of the Titas River flows northward from this area into the abandoned channel belt, opposite of the southward flowing rivers of the delta. We provide results from a detailed investigation of this abandoned channel of the Meghna River using stratigraphic logs of hand-drilled wells, resistivity profiles, sediment analyses and OSL and C14 dating, The OSL ages to be presented constrain the possible date of the event. We employ numerical modeling to evaluate the hypothesis that the co-seismic uplift associated to an earthquake can trigger the channel migration. Our modeling approach aims to estimate the co-seismic uplift associated with potential seismic events using an elastic Coulomb's dislocation model. The geometry fault in our model is estimated using geologic and GPS constraints with standard elastic parameters (Young's modulus = 80 GPa; Poisson's ratio = 0.3). We explored different potential earthquakes geometries that involve the megathrust, a splay fault, or the megathrust terminating in the splay. The magnitude and distribution of co-seismic slip are also varied between a rupture length of 112.5km and 180km along a 225km long fault. We show that any class of models can produce the amount of uplift (1-2 m) necessary for triggering the river

Co-seismic strain changes of Wenchuan Mw7. 9 earthquake recorded by borehole strainmeters on Tibetan plateau

Directory of Open Access Journals (Sweden)

Fu Guangyu

2011-08-01

Full Text Available Co-seismic strain changes of the Wenchuan Mw7. 9 earthquake recorded with three four-component borehole strainmeters showed NW-SE and roughly EW extensions, respectively, at two locations in the interior and northern part of Tibetan plateau, and NS shortening at a location south of the epicenter, in agreement with the tectonic stress field of this region. The observed values of as much as 10−7 are, however, larger than theoretical values obtained with half-space and spherical-earth dislocation theories, implying the existence of other effects, such as local crustal structure and initial stress.

Lower bound earthquake magnitude for probabilistic seismic hazard evaluation

International Nuclear Information System (INIS)

McCann, M.W. Jr.; Reed, J.W.

1990-01-01

This paper presents the results of a study that develops an engineering and seismological basis for selecting a lower-bound magnitude (LBM) for use in seismic hazard assessment. As part of a seismic hazard analysis the range of earthquake magnitudes that are included in the assessment of the probability of exceedance of ground motion must be defined. The upper-bound magnitude is established by earth science experts based on their interpretation of the maximum size of earthquakes that can be generated by a seismic source. The lower-bound or smallest earthquake that is considered in the analysis must also be specified. The LBM limits the earthquakes that are considered in assessing the probability that specified ground motion levels are exceeded. In the past there has not been a direct consideration of the appropriate LBM value that should be used in a seismic hazard assessment. This study specifically looks at the selection of a LBM for use in seismic hazard analyses that are input to the evaluation/design of nuclear power plants (NPPs). Topics addressed in the evaluation of a LBM are earthquake experience data at heavy industrial facilities, engineering characteristics of ground motions associated with small-magnitude earthquakes, probabilistic seismic risk assessments (seismic PRAs), and seismic margin evaluations. The results of this study and the recommendations concerning a LBM for use in seismic hazard assessments are discussed. (orig.)

Fault specific GIS based seismic hazard maps for the Attica region, Greece

Science.gov (United States)

Deligiannakis, G.; Papanikolaou, I. D.; Roberts, G.

2018-04-01

Traditional seismic hazard assessment methods are based on the historical seismic records for the calculation of an annual probability of exceedance for a particular ground motion level. A new fault-specific seismic hazard assessment method is presented, in order to address problems related to the incompleteness and the inhomogeneity of the historical records and to obtain higher spatial resolution of hazard. This method is applied to the region of Attica, which is the most densely populated area in Greece, as nearly half of the country's population lives in Athens and its surrounding suburbs, in the Greater Athens area. The methodology is based on a database of 24 active faults that could cause damage to Attica in case of seismic rupture. This database provides information about the faults slip rates, lengths and expected magnitudes. The final output of the method is four fault-specific seismic hazard maps, showing the recurrence of expected intensities for each locality. These maps offer a high spatial resolution, as they consider the surface geology. Despite the fact that almost half of the Attica region lies on the lowest seismic risk zone according to the official seismic hazard zonation of Greece, different localities have repeatedly experienced strong ground motions during the last 15 kyrs. Moreover, the maximum recurrence for each intensity occurs in different localities across Attica. Highest recurrence for intensity VII (151-156 times over 15 kyrs, or up to a 96 year return period) is observed in the central part of the Athens basin. The maximum intensity VIII recurrence (115 times over 15 kyrs, or up to a 130 year return period) is observed in the western part of Attica, while the maximum intensity IX (73-77/15 kyrs, or a 195 year return period) and X (25-29/15 kyrs, or a 517 year return period) recurrences are observed near the South Alkyonides fault system, which dominates the strong ground motions hazard in the western part of the Attica mainland.

A proposal for seismic evaluation index of mid-rise existing RC buildings in Afghanistan

Science.gov (United States)

Naqi, Ahmad; Saito, Taiki

2017-10-01

Mid-rise RC buildings gradually rise in Kabul and entire Afghanistan since 2001 due to rapid increase of population. To protect the safety of resident, Afghan Structure Code was issued in 2012. But the building constructed before 2012 failed to conform the code requirements. In Japan, new sets of rules and law for seismic design of buildings had been issued in 1981 and severe earthquake damage was disclosed for the buildings designed before 1981. Hence, the Standard for Seismic Evaluation of RC Building published in 1977 has been widely used in Japan to evaluate the seismic capacity of existing buildings designed before 1981. Currently similar problem existed in Afghanistan, therefore, this research examined the seismic capacity of six RC buildings which were built before 2012 in Kabul by applying the seismic screening procedure presented by Japanese standard. Among three screening procedures with different capability, the less detailed screening procedure, the first level of screening, is applied. The study founds an average seismic index (IS-average=0.21) of target buildings. Then, the results were compared with those of more accurate seismic evaluation procedures of Capacity Spectrum Method (CSM) and Time History Analysis (THA). The results for CSM and THA show poor seismic performance of target buildings not able to satisfy the safety design limit (1/100) of the maximum story drift. The target buildings are then improved by installing RC shear walls. The seismic indices of these retrofitted buildings were recalculated and the maximum story drifts were analyzed by CSM and THA. The seismic indices and CSM and THA results are compared and found that building with seismic index larger than (IS-average =0.4) are able to satisfy the safety design limit. Finally, to screen and minimize the earthquake damage over the existing buildings, the judgement seismic index (IS-Judgment=0.5) for the first level of screening is proposed.

Co-Seismic Mass Displacement and its Effect on Earth's Rotation and Gravity

Science.gov (United States)

Chao, B. F.; Gross, R. S.

2004-01-01

Mantle processes often involve large-scale mass transport, ranging from mantle convection, tectonic motions, glacial isostatic adjustment, to tides, atmospheric and oceanic loadings, volcanism and seismicity. On very short time scale of less than an hour, co-seismic event, apart from the "shaking" that is the earthquake, leaves behind permanent (step-function-like) displacements in the crust and mantle. This redistribution of mass changes the Earth's inertia tensor (and hence Earth's rotation in both length-of-day and polar motion), and the gravity field. The question is whether these effects are large enough to be of any significance. In this paper we report updated calculation results based on Chao & Gross. The calculation uses the normal mode summation scheme, applied to over twenty thousand major earthquakes that occurred during 1976-2002, according to source mechanism solutions given by the Harvard Centroid Moment Tensor catalog. Compared to the truly large ones earlier in the century, the earthquakes we study are individually all too small to have left any discernible signature in geodetic records of Earth rotation or global gravity field. However, their collective effects continue to exhibit an extremely strong statistical tendencies, conspiring to decrease J2 and J22 while shortening LOD, resulting in a rounder and more compact Earth. Strong tendency is also seen in the earthquakes trying to "nudge" the Earth rotation pole towards approx. 140 deg.E, roughly opposite to the observed polar drift direction. Currently, the Gravity Recovery And Climate Experiment (GRACE) is measuring the time-variable gravity to high degree and order with unprecedented accuracy. Our results show that great earthquakes such as the 1960 Chilean or 1964 Alaskan events cause gravitational field changes that are large enough to be detected by GRACE.

Microseismic monitoring of CO₂-injection-induced seismicity

Energy Technology Data Exchange (ETDEWEB)

Chen, Yu [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Huang, Lianjie [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-10-03

This presentation's Objectives: Studying moment tensors of microseismic sources; Imaging fracture zones and subsurface structure; Obtaining three-dimension seismic velocity model and improved moment tensors.

Two-dimensional horizontal model seismic test and analysis for HTGR core

International Nuclear Information System (INIS)

Ikushima, Takeshi; Honma, Toshiaki.

1988-05-01

The resistance against earthquakes of high-temperature gas-cooled reactor (HTGR) core with block-type fuels is not fully ascertained yet. Seismic studies must be made if such a reactor plant is to be installed in areas with frequent earthquakes. The paper presented the test results of seismic behavior of a half scale two-dimensional horizontal slice core model and analysis. The following is a summary of the more important results. (1) When the core is subjected to the single axis excitation and simultaneous two-axis excitations to the core across-corners, it has elliptical motion. The core stays lumped motion at the low excitation frequencies. (2) When the load is placed on side fixed reflector blocks from outside to the core center, the core displacement and reflector impact reaction force decrease. (3) The maximum displacement occurs at simultaneous two-axis excitations. The maximum displacement occurs at the single axis excitation to the core across-flats. (4) The results of two-dimensional horizontal slice core model was compared with the results of two-dimensional vertical one. It is clarified that the seismic response of actual core can be predicted from the results of two-dimensional vertical slice core model. (5) The maximum reflector impact reaction force for seismic waves was below 60 percent of that for sinusoidal waves. (6) Vibration behavior and impact response are in good agreement between test and analysis. (author)

The planning of a passive seismic experiment: the Ketzin case

Science.gov (United States)

Rossi, G.; Petronio, L.

2009-04-01

In the last years, it has been recognized the importance of using microseismic activity data to gain information on the state and dynamics of a reservoir, notwithstanding the difficulties of recording, localizing the events, interpret them correctly, in terms of developing fractures, or thermal effects. The increasing number of CO2 storage experiments, with the necessity of providing efficient, economic, and long-term monitoring methods, both in the injection and post-injection phases, further encourage the development and improvement of recording and processing techniques. Microseismic signals are typically recorded with downhole sensors. Monitoring with surface sensors is problematic due to increased noise levels and signal attenuation particularly in the near surface. The actual detection distance depends on background noise conditions, seismic attenuation and the microseismic source strength. In the frame of the European project Co2ReMoVe and of the European Network of Excellence Co2GeoNet, a passive seismic experiment was planned in the Ketzin site for geological storage of CO2, a former gas store near Potsdam, object of the CO2SINK European project and inserted also in the European project Co2ReMoVe. Aim of the survey is to complement the CO2-SINK active seismic downhole experiments, adding precious information on the microseismicity induced by stress field changes at the reservoir level and in the overburden, due to the CO2 injection. The baseline survey was done in May 2008 by the Istituto Nazionale di Oceanografia e di Geofisica Sperimentale-OGS (Italy), with the support of the Deutsches GeoForschungsZentrum-GFZ (Germany) and the collaboration of the Institut für Geowissenschaftliche Gemeinschaftsaufgaben-GGA (Germany), shortly before the starting of the CO2 injection (June 30th 2008). A continuous monitoring (about 5 days) was performed by 2 downhole 3C geophones, and 3 surface 3C geophones located around the wells. This paper, based on the analysis of

Seismic-design questions typify nuclear obstacles

International Nuclear Information System (INIS)

Strauss, S.D.

1979-01-01

The trade-off between safe design of nuclear power plants and cost is considered. As an example, seismic protection problems at the Beaver Valley station of Duquesne Light Co. and their resolution by Stone and Webster Engineering are discussed

Observations and models of Co- and Post-Seismic Deformation Due to the 2015 Mw 7.8 Gorkha (Nepal) Earthquake

Science.gov (United States)

Wang, K.; Fialko, Y. A.

2016-12-01

The 2015 Mw 7.8 Gorkha (Nepal) earthquake occurred along the central Himalayan arc, a convergent boundary between India and Eurasian plates. We use space geodetic data to investigate co- and post-seismic deformation due to the Gorkha earthquake. Because the epicentral area of the earthquake is characterized by strong variations in surface relief and material properties, we developed finite element models that explicitly account for topography and 3-D elastic structure. Compared with slip models obtained using homogenous elastic half-space models, the model including elastic heterogeneity and topography exhibits greater (up to 10%) slip amplitude. GPS observations spanning more than 1 year following the earthquake show overall southward movement and uplift after the Gorkha earthquake, qualitatively similar to the coseismic deformation pattern. Kinematic inversions of GPS data, and forward modeling of stress-driven creep indicate that the observed post-seismic transient is consistent with afterslip on a down-dip extention of the seismic rupture. The Main Himalayan Thrust (MHT) has negligible creep updip of the 2015 rupture, reiterating a future seismic hazard. A poro-elastic rebound may contribute to the observed uplift southward motion, but the predicted surface displacements are small (on the order of 1 cm or less). We also tested a wide range of visco-elastic relaxation models, including 1-D and 3-D variations in the viscosity structure. All tested visco-elastic models predict the opposite signs of horizontal and vertical displacements compared to those observed. Available surface deformation data allow one to rule out a model of a low viscosity channel beneath Tibetan Plateau invoked to explain variations in surface relief at the plateau margins.

Erosion Associated with Seismically-Induced Landslides in the Middle Longmen Shan Region, Eastern Tibetan Plateau, China

Directory of Open Access Journals (Sweden)

Zhikun Ren

2017-08-01

Full Text Available The 2008 Wenchuan earthquake and associated co-seismic landslide was the most recent expression of the rapid deformation and erosion occurring in the eastern Tibetan Plateau. The erosion associated with co-seismic landslides balances the long-term tectonic uplift in the topographic evolution of the region; however, the quantitative relationship between earthquakes, uplift, and erosion is still unknown. In order to quantitatively distinguish the seismically-induced erosion in the total erosion, here, we quantify the Wenchuan earthquake-induced erosion using the digital elevation model (DEM differential method and previously-reported landslide volumes. Our results show that the seismically-induced erosion is comparable with the pre-earthquake short-term erosion. The seismically-induced erosion rate contributes ~50% of the total erosion rate, which suggests that the local topographic evolution of the middle Longmen Shan region may be closely related to tectonic events, such as the 2008 Wenchuan earthquake. We propose that seismically-induced erosion is a very important component of the total erosion, particularly in active orogenic regions. Our results demonstrate that the remote sensing technique of differential DEM provides a powerful tool for evaluating the volume of co-seismic landslides produced in intermountain regions by strong earthquakes.

Measuring snow water equivalent from common-offset GPR records through migration velocity analysis

Directory of Open Access Journals (Sweden)

J. St. Clair

2017-12-01

Full Text Available Many mountainous regions depend on seasonal snowfall for their water resources. Current methods of predicting the availability of water resources rely on long-term relationships between stream discharge and snowpack monitoring at isolated locations, which are less reliable during abnormal snow years. Ground-penetrating radar (GPR has been shown to be an effective tool for measuring snow water equivalent (SWE because of the close relationship between snow density and radar velocity. However, the standard methods of measuring radar velocity can be time-consuming. Here we apply a migration focusing method originally developed for extracting velocity information from diffracted energy observed in zero-offset seismic sections to the problem of estimating radar velocities in seasonal snow from common-offset GPR data. Diffractions are isolated by plane-wave-destruction (PWD filtering and the optimal migration velocity is chosen based on the varimax norm of the migrated image. We then use the radar velocity to estimate snow density, depth, and SWE. The GPR-derived SWE estimates are within 6 % of manual SWE measurements when the GPR antenna is coupled to the snow surface and 3–21 % of the manual measurements when the antenna is mounted on the front of a snowmobile  ∼  0.5 m above the snow surface.

Emissions trading with offset markets and free quota allocations

Energy Technology Data Exchange (ETDEWEB)

Rosendahl, Knut Einar; Strand, Jon

2012-07-01

We study interactions between a 'policy bloc's' emissions quota market and an offset market where emissions offsets can be purchased from a non-policy 'fringe' of countries (such as for the CDM under the Kyoto Protocol). Policy-bloc firms are assumed to benefit from free quota allocations that are updated according to either past emissions or past outputs. We show that both overall abatement, and the allocation of given abatement between the policy bloc and the fringe, tend to be inefficient. When the policy-bloc quota market and offset markets are fully integrated (and firms buy offsets directly from the fringe), and all quotas and offsets must be traded at a single price, it is optimal for the policy bloc to either not constrain the offset market whatsoever, or to ban offsets completely. The former (latter) case occurs when free allocation of quotas is not too generous (very generous), and the offset market can profitably deliver large (only a small) quota amounts. Governments of policy countries would however instead prefer to buy offsets directly from the fringe at a price below the policy-bloc quota price. The offset price will then be below the marginal damage cost of emissions, and the quota price in the policy bloc above marginal damage cost. This solution is also inefficient as the policy bloc (acting as a monopsonist) purchases too few offsets from the fringe.(Author)

Long Period Seismic Waves

Science.gov (United States)

1976-08-01

Geoffsica, TPHM. No. 5 , p. 161. Vargas, Freddy (To he published in 1976) 1 .-DTSCRP1TNACTON DE EVENTO«; NATHDALE«; Y ARTTFTCT ALES. 2.- CALCULO DEL...seismic risk, bv de - fininn relative weiqht of maximum MM intensity at a pivon distance ponulation density, area feolupy and attenuation of intensity wit...Population densitv, area peolopv and attenuation of intensitv with distance, is presented topether with a map anplvinp theorv to Bo- livia. ^«^a

Seismic-safe conditions of blasting near pressure pipe-lines during power installation construction

International Nuclear Information System (INIS)

Smolij, N.I.; Nikitin, A.S.

1980-01-01

Seismic-safe conditions for performing drill-blasting operations in the vicinity of underground gas pipelines when constructing thermal- or nuclear power plants are discussed. It is shown that, for the determination of seismic-safe parameters, of drill-blasting operations, the maximum permissible level of seismic loads should be specified taking into account the mechanical properties of the pipeline.metal, structural parameters of the gas pipeline and the pressure of the medium transported. Besides, the seismic effect of the blast should be considered with regard to particular conditions of blasting and rock properties. The equations and diagrams used in the calculation are given

Sloshing of coolant in a seismically isolated reactor

International Nuclear Information System (INIS)

Wu, T.S.; Guildys, J.; Seidensticker, R.W.

1988-01-01

During a seismic event, the liquid coolant inside the reactor vessel has sloshing motion which is a low-frequency phenomenon. In a reactor system incorporated with seismic isolation, the isolation frequency usually is also very low. There is concern on the potential amplification of sloshing motion of the liquid coolant. This study investigates the effects of seismic isolation on the sloshing of liquid coolant inside the reactor vessel of a liquid metal cooled reactor. Based on a synthetic ground motion whose response spectra envelop those specified by the NRC Regulator Guide 1.60, it is found that the maximum sloshing wave height increases from 18 in. to almost 30 in. when the system is seismically isolated. Since higher sloshing wave may introduce severe impact forces and thermal shocks to the reactor closure and other components within the reactor vessel, adequate design considerations should be made either to suppress the wave height or to reduce the effects caused by high waves

Late Pleistocene and Holocene paleoseismology of an intraplate seismic zone in a large alluvial valley, the New Madrid seismic zone, Central USA

Science.gov (United States)

Guccione, Margaret J.

2005-10-01

. Seven fault segments are recognized by microseismicity and geomorphology. Surface faulting has been recognized at three of these segments, Reelfoot fault, New Madrid North fault, and Bootheel fault. The Reelfoot fault is a compressive stepover along the strike-slip fault and has up to 11 m of surface relief ([Carlson, S.D., 2000. Formation and geomorphic history of Reelfoot Lake: insight into the New Madrid seismic zone. M.S. Thesis, University of Arkansas, Fayetteville, Arkansas, U.S.A]) deforming abandoned and active Mississippi River channels ([Guccione, M.J., Mueller, K., Champion, J., Shepherd, S., Odhiambo, B., 2002b. Stream response to repeated co-seismic folding, Tiptonville dome, western Tennessee. Geomorphology 43 (2002), 313 349]). The New Madrid North fault apparently has only strike-slip motion and is recognized by modern microseismicity, geomorphic anomalies, and sand cataclasis ([Baldwin, J.N., Barron A.D., Kelson, K.I., Harris, J.B., Cashman, S., 2002. Preliminary paleoseismic and geophysical investigation of the North Farrenburg lineament: primary tectonic deformation associated with the New Madrid North Fault?. Seismological Research Letters 73, 393 413]). The Bootheel fault, which is not identified by the modern microseismicity, is associated with extensive liquefaction and offset channels ([Guccione, M.J., Marple, R., Autin, W.J., 2005, Evidence for Holocene displacements on the Bootheel fault (lineament) in southeastern Missouri: Seismotectonic implications for the New Madrid region. Geological Society of America Bulletin 117, 319 333]). The fault has dominantly strike-slip motion but also has a vertical component of slip. Other recognized surface deformation includes relatively low-relief folding at Big Lake/Manila high ([Guccione, M.J., VanArdale, R.B., Hehr, L.H., 2000. Origin and age of the Manila high and associated Big Lake “Sunklands”, New Madrid seismic zone, northeastern Arkansas. Geological Society of America Bulletin 112, 579 590

Seagrass habitat metabolism increases short-term extremes and long-term offset of CO2 under future ocean acidification.

Science.gov (United States)

Pacella, Stephen R; Brown, Cheryl A; Waldbusser, George G; Labiosa, Rochelle G; Hales, Burke

2018-04-10

The role of rising atmospheric CO 2 in modulating estuarine carbonate system dynamics remains poorly characterized, likely due to myriad processes driving the complex chemistry in these habitats. We reconstructed the full carbonate system of an estuarine seagrass habitat for a summer period of 2.5 months utilizing a combination of time-series observations and mechanistic modeling, and quantified the roles of aerobic metabolism, mixing, and gas exchange in the observed dynamics. The anthropogenic CO 2 burden in the habitat was estimated for the years 1765-2100 to quantify changes in observed high-frequency carbonate chemistry dynamics. The addition of anthropogenic CO 2 alters the thermodynamic buffer factors (e.g., the Revelle factor) of the carbonate system, decreasing the seagrass habitat's ability to buffer natural carbonate system fluctuations. As a result, the most harmful carbonate system indices for many estuarine organisms [minimum pH T , minimum Ω arag , and maximum pCO 2(s.w.) ] change up to 1.8×, 2.3×, and 1.5× more rapidly than the medians for each parameter, respectively. In this system, the relative benefits of the seagrass habitat in locally mitigating ocean acidification increase with the higher atmospheric CO 2 levels predicted toward 2100. Presently, however, these mitigating effects are mixed due to intense diel cycling of CO 2 driven by aerobic metabolism. This study provides estimates of how high-frequency pH T , Ω arag , and pCO 2(s.w.) dynamics are altered by rising atmospheric CO 2 in an estuarine habitat, and highlights nonlinear responses of coastal carbonate parameters to ocean acidification relevant for water quality management.

Seagrass habitat metabolism increases short-term extremes and long-term offset of CO2 under future ocean acidification

Science.gov (United States)

Pacella, Stephen R.; Brown, Cheryl A.; Waldbusser, George G.; Labiosa, Rochelle G.; Hales, Burke

2018-04-01

The role of rising atmospheric CO2 in modulating estuarine carbonate system dynamics remains poorly characterized, likely due to myriad processes driving the complex chemistry in these habitats. We reconstructed the full carbonate system of an estuarine seagrass habitat for a summer period of 2.5 months utilizing a combination of time-series observations and mechanistic modeling, and quantified the roles of aerobic metabolism, mixing, and gas exchange in the observed dynamics. The anthropogenic CO2 burden in the habitat was estimated for the years 1765–2100 to quantify changes in observed high-frequency carbonate chemistry dynamics. The addition of anthropogenic CO2 alters the thermodynamic buffer factors (e.g., the Revelle factor) of the carbonate system, decreasing the seagrass habitat’s ability to buffer natural carbonate system fluctuations. As a result, the most harmful carbonate system indices for many estuarine organisms [minimum pHT, minimum Ωarag, and maximum pCO2(s.w.)] change up to 1.8×, 2.3×, and 1.5× more rapidly than the medians for each parameter, respectively. In this system, the relative benefits of the seagrass habitat in locally mitigating ocean acidification increase with the higher atmospheric CO2 levels predicted toward 2100. Presently, however, these mitigating effects are mixed due to intense diel cycling of CO2 driven by aerobic metabolism. This study provides estimates of how high-frequency pHT, Ωarag, and pCO2(s.w.) dynamics are altered by rising atmospheric CO2 in an estuarine habitat, and highlights nonlinear responses of coastal carbonate parameters to ocean acidification relevant for water quality management.

Seismic Response of Deep Hydrocarbon Bearing Reservoirs: examples from Oso Field and implications for Future Opportunities

International Nuclear Information System (INIS)

Oluwasusi, A. B.; Hussey, V.; Goulding, F. J.

2002-01-01

The Oso Field (OML 70) produces approximately 100 TBD of condensate from Miocene age shelfal sand reservoirs at approximately 10,000 feet below sea level. The field was discovered in 1967 while testing a deeply buried fault closure. Reservoirs are normally pressured, exceed 1 Darcy in permeability and range from 50 to 600 feet in thickness.There are seismic amplitudes associated with the shallower reservoirs on the existing conventional 3D dataset; however there are no anomalies associated with the deeper, condensate accumulations.The paper explores the physical rock and fluid properties associated with the Oso reservoirs and the resulting seismic responses. Modelled results have been calibrated with the actual seismic signatures for the water and hydrocarbon bearing zones. Results indicate that the deeper reservoirs exhibit a classic Class II AVG seismic response and that the use of longer offset and angle stack data can help predict the occurrence of these types of reservoirs. Examples of similar accumulations will be shared.Mobil Producing Nigeria is conducting a full reprocessing effort of the existing 3D dataset over the Joint Venture acreage with a goal of identifying and exploiting additional accumulations with Class II AVG seismic response. Preliminary results of the reprocessing over known accumulations will be presented

22 CFR 1007.8 - Procedures for salary offset.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 2 2010-04-01 2010-04-01 true Procedures for salary offset. 1007.8 Section 1007.8 Foreign Relations INTER-AMERICAN FOUNDATION SALARY OFFSET § 1007.8 Procedures for salary offset... final salary or leave payments in accordance with 31 U.S.C. 3716. ...

USE OF BOUNDING ANALYSES TO ESTIMATE THE PREFORMANCE OF A SEISMICALLY ISOLATED STRUCTURE

Directory of Open Access Journals (Sweden)

Gökhan ÖZDEMİR

2017-03-01

Full Text Available Current design approach for seismic isolated structures is to perform bounding analyses. These analyses provide an envelope for the response of the seismic isolated structure rather than focusing on the actual performance. In this study, the success of bounding analyses to estimate performance of a seismic isolated structure, in which the isolation is provided by means of lead rubber bearings (LRBs, is evaluated in a comparative manner. For this purpose, nonlinear response history analyses were performed under the effect of bidirectional ground motion excitations. In bounding analyses, non-deteriorating hysteretic representations were used to model the hysteretic behavior of LRBs. On the other hand, to estimate the actual performance of both the superstructure and isolator units, deteriorating hysteretic idealizations were employed. The deterioration in strength of LRBs was defined as a function of temperature rise in the lead core. The analyzed structure is an existing seismically isolated hospital building and analytically modeled in accordance with its reported design properties for both isolation units and superstructure. Results obtained from analyses where LRBs are idealized by both deteriorating and non-deteriorating hysteretic representations are used in the comparisons. The response quantities used in the comparisons are maximum isolator displacement, maximum isolator force, maximum absolute floor acceleration, and maximum relative story displacements. In an average sense, bounding analyses is found to provide conservative estimates for the selected response quantities and fulfills its intended purpose. However, it is revealed that there may be individual cases where bounding analyses fails to provide a safe envelope.

Sequence stratigraphy, seismic stratigraphy, and seismic structures of the lower intermediate confining unit and most of the Floridan aquifer system, Broward County, Florida

Science.gov (United States)

Cunningham, Kevin J.; Kluesner, Jared W.; Westcott, Richard L.; Robinson, Edward; Walker, Cameron; Khan, Shakira A.

2017-12-08

��an approach never before applied to this area. Notably, the 3D geomodeling provided 3D visualizations and geocellular models of the depositional sequences, hydrostratigraphy, and structural features. The geocellular data could be used to update the hydrogeologic structure inherent to groundwater flow simulations that are designed to address the sustainability of the water resources of the Floridan aquifer system.Two kinds of pathways that could enable upward cross-formational flow of injected treated wastewater from the Boulder Zone have been identified in the 80 miles of high-resolution seismic data collected for this study: a near-vertical reverse fault and karst collapse structures. The single reverse fault, inferred to be of tectonic origin, is in extreme northeastern Broward County and has an offset of about 19 feet at the level of the Arcadia Formation. Most of the 17 karst collapse structures identified manifest as columniform, vertically stacked sagging seismic reflections that span early Eocene to Miocene age rocks equivalent to much of the Floridan aquifer system and the lower part of the overlying intermediate confining unit. In some cases, the seismic-sag structures extend upward into strata of Pliocene age. The seismic-sag structures are interpreted to have a semicircular shape in plan view on the basis of comparison to (1) other seismic-sag structures in southeastern Florida mapped with two 2D seismic cross lines or 3D data, (2) comparison to these structures located in other carbonate provinces, and (3) plausible extensional ring faults detected with multi-attribute analysis. The seismic-sag structures in the study area have heights as great as 2,500 vertical feet, though importantly, one spans about 7,800 feet. Both multi-attribute analysis and visual detection of offset of seismic reflections within the seismic-sag structures indicate faults and fractures are associated with many of the structures. Multi-attribute analysis highlighting chimney fluid pathways

Effects of Irregular Bridge Columns and Feasibility of Seismic Regularity

Science.gov (United States)

Thomas, Abey E.

2018-05-01

Bridges with unequal column height is one of the main irregularities in bridge design particularly while negotiating steep valleys, making the bridges vulnerable to seismic action. The desirable behaviour of bridge columns towards seismic loading is that, they should perform in a regular fashion, i.e. the capacity of each column should be utilized evenly. But, this type of behaviour is often missing when the column heights are unequal along the length of the bridge, allowing short columns to bear the maximum lateral load. In the present study, the effects of unequal column height on the global seismic performance of bridges are studied using pushover analysis. Codes such as CalTrans (Engineering service center, earthquake engineering branch, 2013) and EC-8 (EN 1998-2: design of structures for earthquake resistance. Part 2: bridges, European Committee for Standardization, Brussels, 2005) suggests seismic regularity criterion for achieving regular seismic performance level at all the bridge columns. The feasibility of adopting these seismic regularity criterions along with those mentioned in literatures will be assessed for bridges designed as per the Indian Standards in the present study.

A deterministic seismic hazard map of India and adjacent areas

International Nuclear Information System (INIS)

Parvez, Imtiyaz A.; Vaccari, Franco; Panza, Giuliano

2001-09-01

A seismic hazard map of the territory of India and adjacent areas has been prepared using a deterministic approach based on the computation of synthetic seismograms complete of all main phases. The input data set consists of structural models, seismogenic zones, focal mechanisms and earthquake catalogue. The synthetic seismograms have been generated by the modal summation technique. The seismic hazard, expressed in terms of maximum displacement (DMAX), maximum velocity (VMAX), and design ground acceleration (DGA), has been extracted from the synthetic signals and mapped on a regular grid of 0.2 deg. x 0.2 deg. over the studied territory. The estimated values of the peak ground acceleration are compared with the observed data available for the Himalayan region and found in good agreement. Many parts of the Himalayan region have the DGA values exceeding 0.6 g. The epicentral areas of the great Assam earthquakes of 1897 and 1950 represent the maximum hazard with DGA values reaching 1.2-1.3 g. (author)

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 4B. Paks NPP: Analysis/testing. Working material

International Nuclear Information System (INIS)

1995-01-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports on dynamic study of the main building of the Paks NPP; shake table investigation at Paks NPP and the Final report of the Co-ordinated Research Programme

Accuracy and sensitivity analysis on seismic anisotropy parameter estimation

Science.gov (United States)

Yan, Fuyong; Han, De-Hua

2018-04-01

There is significant uncertainty in measuring the Thomsen’s parameter δ in laboratory even though the dimensions and orientations of the rock samples are known. It is expected that more challenges will be encountered in the estimating of the seismic anisotropy parameters from field seismic data. Based on Monte Carlo simulation of vertical transversely isotropic layer cake model using the database of laboratory anisotropy measurement from the literature, we apply the commonly used quartic non-hyperbolic reflection moveout equation to estimate the seismic anisotropy parameters and test its accuracy and sensitivities to the source-receive offset, vertical interval velocity error and time picking error. The testing results show that the methodology works perfectly for noise-free synthetic data with short spread length. However, this method is extremely sensitive to the time picking error caused by mild random noises, and it requires the spread length to be greater than the depth of the reflection event. The uncertainties increase rapidly for the deeper layers and the estimated anisotropy parameters can be very unreliable for a layer with more than five overlain layers. It is possible that an isotropic formation can be misinterpreted as a strong anisotropic formation. The sensitivity analysis should provide useful guidance on how to group the reflection events and build a suitable geological model for anisotropy parameter inversion.

Geochemical variations during the 2012 Emilia seismic sequence

Science.gov (United States)

Sciarra, Alessandra; Cantucci, Barbara; Galli, Gianfranco; Cinti, Daniele; Pizzino, Luca

2015-04-01

Several geochemical surveys (soil gas and shallow water) were performed in the Modena province (Massa Finalese, Finale Emilia, Medolla and S. Felice sul Panaro), during 2006-2014 period. In May-June 2012, a seismic sequence (main shocks of ML 5.9 and 5.8) was occurred closely to the investigated area. In this area 300 CO2 and CH4 fluxes measurements, 150 soil gas concentrations (He, H2, CO2, CH4 and C2H6), 30 shallow waters and their isotopic analyses (δ13C- CH4, δD- CH4 and δ13C- CO2) were performed in April-May 2006, October and December 2008, repeated in May and September 2012, June 2013 and July 2014 afterwards the 2012 Emilia seismic sequences. Chemical composition of soil gas are dominated by CH4 in the southern part by CO2 in the northern part. Very anomalous fluxes and concentrations are recorded in spot areas; elsewhere CO2 and CH4 values are very low, within the typical range of vegetative and of organic exhalation of the cultivated soil. After the seismic sequence the CH4 and CO2 fluxes are increased of one order of magnitude in the spotty areas, whereas in the surrounding area the values are within the background. On the contrary, CH4 concentration decrease (40%v/v in the 2012 surveys) and CO2 concentration increase until to 12.7%v/v (2013 survey). Isotopic gas analysis were carried out only on samples with anomalous values. Pre-seismic data hint a thermogenic origin of CH4 probably linked to leakage from a deep source in the Medolla area. Conversely, 2012/2013 isotopic data indicate a typical biogenic origin (i.e. microbial hydrocarbon production) of the CH4, as recognized elsewhere in the Po Plain and surroundings. The δ13C-CO2 value suggests a prevalent shallow origin of CO2 (i.e. organic and/or soil-derived) probably related to anaerobic oxidation of heavy hydrocarbons. Water samples, collected from domestic, industrial and hydrocarbons exploration wells, allowed us to recognize different families of waters. Waters are meteoric in origin and

17 CFR 141.8 - Procedures for salary offset.

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 1 2010-04-01 2010-04-01 false Procedures for salary offset. 141.8 Section 141.8 Commodity and Securities Exchanges COMMODITY FUTURES TRADING COMMISSION SALARY OFFSET § 141.8 Procedures for salary offset. (a) Deductions to liquidate an employee's debt will be by...

38 CFR 1.992 - Procedures for salary offset.

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Procedures for salary offset. 1.992 Section 1.992 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS GENERAL PROVISIONS Salary Offset Provisions § 1.992 Procedures for salary offset. (a) Types of collection...

22 CFR 34.16 - Procedures for salary offset.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Procedures for salary offset. 34.16 Section 34.16 Foreign Relations DEPARTMENT OF STATE CLAIMS AND STOLEN PROPERTY DEBT COLLECTION Salary Offset § 34.16 Procedures for salary offset. Unless otherwise provided by statute or contract, the following...

Integrated seismic analysis of the Chalk Group in eastern Denmark—Implications for estimates of maximum palaeo-burial in southwest Scandinavia

DEFF Research Database (Denmark)

Nielsen, Lars; Boldreel, Lars Ole; Hansen, Thomas Mejer

2011-01-01

Group. The sonic velocities are consistent with the overall seismic layering, although they show additional fine-scale layering. Integration of gamma and sonic log with porosity data shows that seismic velocity is sensitive to clay content. In intervals near boundaries of the refraction model, moderate......The origin of the topography of southwest Scandinavia is subject to discussion. Analysis of borehole seismic velocity has formed the basis for interpretation of several hundred metres of Neogene uplift in parts of Denmark.Here, refraction seismic data constrain a 7.5km long P-wave velocity model...... of the Chalk Group below the Stevns peninsula, eastern part of the Danish Basin. The model contains four layers in the ~860m thick Chalk Group with mean velocities of 2.2km/s, 2.4km/s, 3.1km/s, and 3.9–4.3km/s. Sonic and gamma wireline log data from two cored boreholes represent the upper ~450m of the Chalk...

Rock formation characterization for carbon dioxide geosequestration: 3D seismic amplitude and coherency anomalies, and seismic petrophysical facies classification, Wellington and Anson-Bates Fields, Kansas, USA

Science.gov (United States)

Ohl, Derek; Raef, Abdelmoneam

2014-04-01

Higher resolution rock formation characterization is of paramount priority, amid growing interest in injecting carbon dioxide, CO2, into subsurface rock formations of depeleting/depleted hydrocarbon reservoirs or saline aquifers in order to reduce emissions of greenhouse gases. In this paper, we present a case study for a Mississippian carbonate characterization integrating post-stack seismic attributes, well log porosities, and seismic petrophysical facies classification. We evaluated changes in petrophysical lithofacies and reveal structural facies-controls in the study area. Three cross-plot clusters in a plot of well log porosity and acoustic impedance corroborated a Neural Network petrophysical facies classification, which was based on training and validation utilizing three petrophysically-different wells and three volume seismic attributes, extracted from a time window including the wavelet of the reservoir-top reflection. Reworked lithofacies along small-throw faults has been revealed based on comparing coherency and seismic petrophysical facies. The main objective of this study is to put an emphasis on reservoir characterization that is both optimized for and subsequently benefiting from pilot tertiary CO2 carbon geosequestration in a depleting reservoir and also in the deeper saline aquifer of the Arbuckle Group, south central Kansas. The 3D seismic coherency attribute, we calculated from a window embracing the Mississippian top reflection event, indicated anomalous features that can be interpreted as a change in lithofacies or faulting effect. An Artificial Neural Network (ANN) lithofacies modeling has been used to better understand these subtle features, and also provide petrophysical classes, which will benefit flow-simulation modeling and/or time-lapse seismic monitoring feasibility analysis. This paper emphasizes the need of paying greater attention to small-scale features when embarking upon characterization of a reservoir or saline-aquifer for CO2

16 CFR 1027.8 - Procedures for salary offset.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Procedures for salary offset. 1027.8 Section 1027.8 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION GENERAL SALARY OFFSET § 1027.8 Procedures for salary offset. (a) Deductions to liquidate an employee's debt will be by the method and in the...

5 CFR 1215.8 - Procedures for salary offset.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Procedures for salary offset. 1215.8... MANAGEMENT Salary Offset § 1215.8 Procedures for salary offset. (a) Deductions to liquidate an employee's... payment due to a separated employee including but not limited to final salary payment or leave in...

45 CFR 607.8 - Procedures for salary offset.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 3 2010-10-01 2010-10-01 false Procedures for salary offset. 607.8 Section 607.8 Public Welfare Regulations Relating to Public Welfare (Continued) NATIONAL SCIENCE FOUNDATION SALARY OFFSET § 607.8 Procedures for salary offset. (a) Deductions to liquidate an employee's debt will be by...

32 CFR 1697.8 - Procedures for salary offset.

Science.gov (United States)

2010-07-01

... 32 National Defense 6 2010-07-01 2010-07-01 false Procedures for salary offset. 1697.8 Section 1697.8 National Defense Other Regulations Relating to National Defense SELECTIVE SERVICE SYSTEM SALARY OFFSET § 1697.8 Procedures for salary offset. (a) Deductions to liquidate an employee's debt will be by...

14 CFR 1261.603 - Procedures for salary offset.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Procedures for salary offset. 1261.603... salary offset. If NASA is both the paying and creditor agency, the following requirements must be met... of the debt through salary offset by deductions from the employee's current disposable pay, stating...

5 CFR 179.212 - Procedures for salary offset.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Procedures for salary offset. 179.212... COLLECTION STANDARDS Salary Offset § 179.212 Procedures for salary offset. (a) The Director or his or her designee shall coordinate salary deductions under this subpart. (b) OPM payroll office shall determine the...

47 CFR 1.1951 - Offset against tax refunds.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Offset against tax refunds. 1.1951 Section 1... Claims Owed the United States Cooperation with the Internal Revenue Service § 1.1951 Offset against tax refunds. The Commission will take action to effect administrative offset against tax refunds due to...

Crustal Deformation around Zhangjiakou-Bohai Seismically Active Belt

Science.gov (United States)

Jin, H.; Fu, G.; Kato, T.

2011-12-01

Zhangjiakou-Bohai belt is a seismically active belt located in Northern China around Beijing, the capital of China. Near such a belt many great earthquakes occurred in the past centuries (e.g. the 1976 Tanshan Ms7.8 earthquake, the 1998 Zhangbei Ms6.2 earthquake, etc). Chinese Government established dense permanent and regional Global Positioning System (GPS) stations in and near the area. We collected and analyzed all the GPS observation data between 1999 and 2009 around Zhangjiakou-Bohai seismic belt, and obtained velocities at 143 stations. At the same time we investigated Zhangjiakou-Bohai belt slip rate for three profiles from northwest to southeast, and constructed a regional strain field on the Zhangjiakou-Bohai seismic belt region by least-square collocation. Based on the study we found that: 1) Nowadays the Zhangjiakou-Bohai seismic belt is creeping with left-lateral slip rate of 2.0mm~2.4mm/a, with coupling depth of 35~50km; 2) In total, the slip and coupling depth of the northwestern seismic belt is less than the one of southeast side; 3) The maximum shear strain is about 3×10-8 at Beijing-Tianjin-Tangshan area.

Offsetting China's CO2 Emissions by Soil Carbon Sequestration

International Nuclear Information System (INIS)

Lal, R.

2004-01-01

Fossil fuel emissions of carbon (C) in China in 2000 was about 1 Pg/yr, which may surpass that of the U.S. (1.84 Pg C) by 2020. Terrestrial C pool of China comprises about 35 to 60 Pg in the forest and 120 to 186 Pg in soils. Soil degradation is a major issue affecting 145 Mha by different degradative processes, of which 126 Mha are prone to accelerated soil erosion. Similar to world soils, agricultural soils of China have also lost 30 to 50% or more of the antecedent soil organic carbon (SOC) pool. Some of the depleted SOC pool can be re-sequestered through restoration of degraded soils, and adoption of recommended management practices. The latter include conversion of upland crops to multiple cropping and rice paddies, adoption of integrated nutrient management (INM) strategies, incorporation of cover crops in the rotations cycle and adoption of conservation-effective systems including conservation tillage. A crude estimated potential of soil C sequestration in China is 119 to 226 Tg C/y of SOC and 7 to 138 Tg C/y for soil inorganic carbon (SIC) up to 50 years. The total potential of soil C sequestration is about 12 Pg, and this potential can offset about 25% of the annual fossil fuel emissions in China

Feasibility of Seismic Monitoring at a Potential CO2 Injection Test Site in the Paris Basin Évaluation des apports de la sismique à la surveillance d’un test d’injection de CO2 sur un site pilote potentiel du Bassin de Paris

OpenAIRE

Becquey M.; Lucet N.; Huguet F.

2009-01-01

Seismic effects of the injection of CO2 into a partially depleted oil field have been evaluated. Seismic modelling yields small time-lapse effects, including 0.4 ms time-shifts and 4 to 6% amplitude variations at the top and bottom of the reservoir. Amplitude variations at the reservoir level should be slightly larger at large incidence angles, but wave equation modelling shows that picking these reflections will not be easy, because of the presence of shear waves generated at upper inte...

Governing the carbon offset market

OpenAIRE

Lovell, Heather C.

2010-01-01

Carbon offsets are produced and sold under the international climate change regime (the United Nations Kyoto Protocol) and also within an expanding voluntary offset market in which companies and individuals can voluntarily opt to compensate for their greenhouse gas emissions. The volume of carbon produced and consumed within compliance and voluntary markets has grown dramatically in the last 5 years, raising a number of governance challenges. This Focus Article gives an overview of the govern...

Vertical seismic profile data from well Mallik 2L-38 for gas hydrate studies

Energy Technology Data Exchange (ETDEWEB)

Mi, Y [Calgary Univ., AB (Canada). Dept. of Geology and Geophysics; Walia, R [Victoria Univ., BC (Canada) School of Earth and Ocean Sciences; Hyndman, R [Geological Survey of Canada, Sidney, BC (Canada) Pacific Geoscience Centre

1999-07-01

A gas hydrate research well was drilled in the Canadian Arctic to study gas hydrates in a permafrost setting in a collaborative research project between the Japan National Oil Corp., the Geological Survey of Canada and other agencies. The multidisciplinary study included an electromagnetic survey, permafrost and gas hydrate coring, comprehensive downhole geophysical logging and measurement. Laboratory studies concerned studies on recovered cuttings and core including sedimentology, physical properties, geochemistry, and reservoir characteristics of the Mallik gas accumulation. As part of the Mallik 2L-38 field program, a vertical seismic profiling survey was conducted at zero and other offset source positions with three component receiver tools and horizontal and vertical vibration sources. A special effort was made to record shear wave data, which will be used to estimate the effect of gas hydrate on formation velocities and to determine gas hydrate concentration as a function of the Mallik gas accumulation. From the initial VSP analysis, certain conclusions follow: 1) zero offset vertical vibration component Z and horizontal X component data give reliable velocity determination within the gas hydrate formation zone. P wave velocities from offset VSP data show an excellent consistency with that from offset data and with the sonic log. And 2) the VSP data permit reliable identification of gas hydrate bearing zones. Abstract only included.

The Seismicity of Two Hyperextended Margins

Science.gov (United States)

Redfield, Tim; Terje Osmundsen, Per

2013-04-01

, loads generated by escarpment erosion, offshore sedimentary deposition, and post-glacial rebound have been periodically superimposed throughout the Neogene. Their vertical stress patterns are mutually-reinforcing during deglaciation. However, compared to the post-glacial dome the pattern of maximum uplift/unloading generated by escarpment erosion will be longer, more linear, and located atop the emergent proximal margin. The pattern of offshore maximum deposition/loading will be similar. This may help explain the asymmetric expenditure of Fennoscandia's annual seismic energy budget. It may also help explain the obvious Conundrum: if stress generated by erosion and deposition is sufficiently great, fault reactivation and consequent seismicity can occur at any hyperextended passive margin sector regardless of its glacial history. Onshore Scandinavia, episodic footwall uplift and escarpment rejuvenation may have been driven by just such a mechanism throughout much of the later Cretaceous and Cenozoic. SE Brasil offers a glimpse of how Norway's hyperextended margin might manifest itself seismically in the absence of post-glacial rebound. Compilations suggest two seismic belts may exist. One, offshore, follows the thinned crust of the ultra-deep, hyperextended Campos and Santos basins. Onshore, earthquakes occur more commonly in the elevated highlands of the escarpments, and track especially the long, linear ranges such as the Serra de Mantiquiera and Serra do Espinhaço. Seismicity is more rare in the coastal lowlands, and largely absent in the Brasilian hinterland. Although never glaciated since the time of hyperextension and characterized by significantly fewer earthquakes in toto, SE Brasil's pattern of seismicity closely mimics Scandinavia. Commencing after perhaps just a few tens of millions of years of 'sag' basin infill, accommodation phase fault reactivation and footwall uplift at passive margins is the inexorable product of hyperextension. CITATIONS Redfield, T

29 CFR 1650.110 - Implementation of salary offset.

Science.gov (United States)

2010-07-01

... 29 Labor 4 2010-07-01 2010-07-01 false Implementation of salary offset. 1650.110 Section 1650.110... Procedures for the Collection of Debts by Salary Offset § 1650.110 Implementation of salary offset. (a... proposed voluntary repayment agreement, deductions will begin in the next bi-weekly salary payment after a...

45 CFR 33.10 - Procedures for salary offset.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 1 2010-10-01 2010-10-01 false Procedures for salary offset. 33.10 Section 33.10 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION SALARY OFFSET § 33.10 Procedures for salary offset. (a) Method and source of deductions. Unless the employee and the Secretary have...

3D seismic data de-noising and reconstruction using Multichannel Time Slice Singular Spectrum Analysis

Science.gov (United States)

Rekapalli, Rajesh; Tiwari, R. K.; Sen, Mrinal K.; Vedanti, Nimisha

2017-05-01

Noises and data gaps complicate the seismic data processing and subsequently cause difficulties in the geological interpretation. We discuss a recent development and application of the Multi-channel Time Slice Singular Spectrum Analysis (MTSSSA) for 3D seismic data de-noising in time domain. In addition, L1 norm based simultaneous data gap filling of 3D seismic data using MTSSSA also discussed. We discriminated the noises from single individual time slices of 3D volumes by analyzing Eigen triplets of the trajectory matrix. We first tested the efficacy of the method on 3D synthetic seismic data contaminated with noise and then applied to the post stack seismic reflection data acquired from the Sleipner CO2 storage site (pre and post CO2 injection) from Norway. Our analysis suggests that the MTSSSA algorithm is efficient to enhance the S/N for better identification of amplitude anomalies along with simultaneous data gap filling. The bright spots identified in the de-noised data indicate upward migration of CO2 towards the top of the Utsira formation. The reflections identified applying MTSSSA to pre and post injection data correlate well with the geology of the Southern Viking Graben (SVG).

Seismic alarm system for Ignalina nuclear power plant

International Nuclear Information System (INIS)

Wieland, M.; Griesser, L.; Austin, G.E.; Tiurin, S.; Kuendig, C.

2001-01-01

A seismic alarm system will be installed at the Ignalina Nuclear Power Plant (INPP) in Lithuania. There are two reactors, both RMBK 1500 MW units. Each reactor is a water cooled, graphite moderated, channel type reactor. INPP has the most advanced version of the RMBK reactor design series. The first and second units of INPP went into service at the end of 1983 and in August 1987 respectively. Their design lifetime is approx. 30 years. The various buildings and plant have been designed for two earthquake levels, that is the design earthquake and the maximum possible earthquake with peak ground accelerations ranging from 1.2% to 10% of the acceleration due to gravity. Certain parts of the buildings and some of the equipment of the first and second units do not comply with Western seismic standards. As seismic strengthening of the existing buildings and equipment is not feasible economically, a reactor protection system based on an earthquake early warning system was recommended. This system essentially consists of six seismic stations encircling INPP at a radial distance of approx. 30 km and a seventh station at INPP. Each station includes three seismic substations each 500 m apart. The ground motion at each station is measured continuously by three accelerometers and one seismometer. Data is transmitted via telemetry to the control centre at INPP. Early warning alarms are generated if a seismic threshold is exceeded. This paper discusses the characteristics of INPP, the seismic alarm system presently under construction and the experience with other early warning and seismic alarm systems. (author)

40 CFR 13.21 - Employee salary offset-general.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Employee salary offset-general. 13.21... STANDARDS Administrative Offset § 13.21 Employee salary offset—general. (a) Purpose. This section... collection by salary offset under 5 U.S.C. 5514 of debts owed EPA and debts owed to other Federal agencies by...

45 CFR 708.10 - Procedures for salary offset.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 3 2010-10-01 2010-10-01 false Procedures for salary offset. 708.10 Section 708... COLLECTION BY SALARY OFFSET FROM INDEBTED CURRENT AND FORMER EMPLOYEES § 708.10 Procedures for salary offset... to final salary payment, retired pay, or lump sum leave, etc. as of the date of separation to the...

Groundwater penetrating radar and high resolution seismic for locating shallow faults in unconsolidated sediments

International Nuclear Information System (INIS)

Wyatt, D.E.

1993-01-01

Faults in shallow, unconsolidated sediments, particularly in coastal plain settings, are very difficult to discern during subsurface exploration yet have critical impact to groundwater flow, contaminant transport and geotechnical evaluations. This paper presents a case study using cross-over geophysical technologies in an area where shallow faulting is probable and known contamination exists. A comparison is made between Wenner and dipole-dipole resistivity data, ground penetrating radar, and high resolution seismic data. Data from these methods were verified with a cone penetrometer investigation for subsurface lithology and compared to existing monitoring well data. Interpretations from these techniques are compared with actual and theoretical shallow faulting found in the literature. The results of this study suggests that (1) the CPT study, combined with the monitoring well data may suggest that discontinuities in correlatable zones may indicate that faulting is present (2) the addition of the Wenner and dipole-dipole data may further suggest that offset zones exist in the shallow subsurface but not allow specific fault planes or fault stranding to be mapped (3) the high resolution seismic data will image faults to within a few feet of the surface but does not have the resolution to identify the faulting on the scale of our models, however it will suggest locations for upward continuation of faulted zones (4) offset 100 MHz and 200 MHz CMP GPR will image zones and features that may be fault planes and strands similar to our models (5) 300 MHz GPR will image higher resolution features that may suggest the presence of deeper faults and strands, and (6) the combination of all of the tools in this study, particularly the GPR and seismic may allow for the mapping of small scale, shallow faulting in unconsolidated sediments

3. General principles of assessing seismic resistance of technological equipment of nuclear power plants

International Nuclear Information System (INIS)

1983-01-01

The evaluation of the seismic resistance of technological equipment is performed by computation, experimental trial, possibly by combining both methods. Existing and prepared standards in the field of seismic resistance of nuclear power plants are mentioned. Accelerograms and response spectra of design-basis earhtquake and maximum credible earthquake serve as the basic data for evaluating seismic resistance. The nuclear power plant in Mochovce will be the first Czechoslovak nuclear power plant with so-called partially seismic design. The problem of dynamic interaction of technological equipment and nuclear power plant systems with a bearing structure is discussed. (E.F.)

Are forestation, bio-char and landfilled biomass adequate offsets for the climate effects of burning fossil fuels?

NARCIS (Netherlands)

Reijnders, L.

2009-01-01

Forestation and landfilling purpose-grown biomass are not adequate offsets for the CO2 emission from burning fossil fuels. Their permanence is insufficiently guaranteed and landfilling purpose-grown biomass may even be counterproductive. As to permanence, bio-char may do better than forests or

Economic and ecological outcomes of flexible biodiversity offset systems.

Science.gov (United States)

Habib, Thomas J; Farr, Daniel R; Schneider, Richard R; Boutin, Stan

2013-12-01

The commonly expressed goal of biodiversity offsets is to achieve no net loss of specific biological features affected by development. However, strict equivalency requirements may complicate trading of offset credits, increase costs due to restricted offset placement options, and force offset activities to focus on features that may not represent regional conservation priorities. Using the oil sands industry of Alberta, Canada, as a case study, we evaluated the economic and ecological performance of alternative offset systems targeting either ecologically equivalent areas (vegetation types) or regional conservation priorities (caribou and the Dry Mixedwood natural subregion). Exchanging dissimilar biodiversity elements requires assessment via a generalized metric; we used an empirically derived index of biodiversity intactness to link offsets with losses incurred by development. We considered 2 offset activities: land protection, with costs estimated as the net present value of profits of petroleum and timber resources to be paid as compensation to resource tenure holders, and restoration of anthropogenic footprint, with costs estimated from existing restoration projects. We used the spatial optimization tool MARXAN to develop hypothetical offset networks that met either the equivalent-vegetation or conservation-priority targets. Networks that required offsetting equivalent vegetation cost 2-17 times more than priority-focused networks. This finding calls into question the prudence of equivalency-based systems, particularly in relatively undeveloped jurisdictions, where conservation focuses on limiting and directing future losses. Priority-focused offsets may offer benefits to industry and environmental stakeholders by allowing for lower-cost conservation of valued ecological features and may invite discussion on what land-use trade-offs are acceptable when trading biodiversity via offsets. Resultados Económicos y Ecológicos de Sistemas de Compensación de

Seismicity of the Paradox Basin and the Colorado Plateau interior

International Nuclear Information System (INIS)

Wong, I.G.

1984-04-01

National Waste Terminal Storage Program site qualification criteria require that a nuclear waste repository be located so that ground motion associated with the maximum credible and maximum probable earthquakes or other earthquake-associated effects will not have an unacceptable adverse impact on system performance. To determine whether a potential repository site located in the Paradox salt formation in the Paradox Basin of southeastern Utah satisfies these criteria, seismological studies were undertaken by Woodward-Clyde Consultants (WCC) in March 1978. These studies included: (1) analysis of historical seismicity; (2) analysis of contemporary seismicity and tectonics of both the Paradox Basin and surrounding Colorado Plateau, including an extensive program of microearthquake monitoring; (3) evaluation of the Paradox Basin crustal structure; (4) evaluation of mining-induced seismicity; and (5) characterization of design-related earthquake-induced ground motions pertinent to a potential repository site through studies of attentation and subsurface ground motions. A detailed discussion of the results of the seismological studies performed through December 1980 is contained in WCC (1982). The purpose of this topical report is to update and summarize the studies on the local, regional, and mining-induced seismicity conducted through December 1982. The limitations of any interpretations are also discussed and additional information that remains to be acquired is identified. 56 references, 45 figures, 4 tables

Common-image gathers in the offset domain from reverse-time migration

KAUST Repository

Zhan, Ge

2014-04-01

Kirchhoff migration is flexible to output common-image gathers (CIGs) in the offset domain by imaging data with different offsets separately. These CIGs supply important information for velocity model updates and amplitude-variation-with-offset (AVO) analysis. Reverse-time migration (RTM) offers more insights into complex geology than Kirchhoff migration by accurately describing wave propagation using the two-way wave equation. But, it has difficulty to produce offset domain CIGs like Kirchhoff migration. In this paper, we develop a method for obtaining offset domain CIGs from RTM. The method first computes the RTM operator of an offset gather, followed by a dot product of the operator and the offset data to form a common-offset RTM image. The offset domain CIGs are then achieved after separately migrating data with different offsets. We generate offset domain CIGs on both the Marmousi synthetic data and 2D Gulf of Mexico real data using this approach. © 2014.

Modeling of CO2 storage in aquifers

International Nuclear Information System (INIS)

Savioli, Gabriela B; Santos, Juan E

2011-01-01

Storage of CO 2 in geological formations is a means of mitigating the greenhouse effect. Saline aquifers are a good alternative as storage sites due to their large volume and their common occurrence in nature. The first commercial CO 2 injection project is that of the Sleipner field in the Utsira Sand aquifer (North Sea). Nevertheless, very little was known about the effectiveness of CO 2 sequestration over very long periods of time. In this way, numerical modeling of CO 2 injection and seismic monitoring is an important tool to understand the behavior of CO 2 after injection and to make long term predictions in order to prevent CO 2 leaks from the storage into the atmosphere. The description of CO 2 injection into subsurface formations requires an accurate fluid-flow model. To simulate the simultaneous flow of brine and CO 2 we apply the Black-Oil formulation for two phase flow in porous media, which uses the PVT data as a simplified thermodynamic model. Seismic monitoring is modeled using Biot's equations of motion describing wave propagation in fluid-saturated poroviscoelastic solids. Numerical examples of CO 2 injection and time-lapse seismics using data of the Utsira formation show the capability of this methodology to monitor the migration and dispersal of CO 2 after injection.

A microseismic workflow for managing induced seismicity risk as CO₂ storage projects

Energy Technology Data Exchange (ETDEWEB)

Matzel, E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Morency, C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Pyle, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Templeton, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); White, J. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2015-10-27

It is well established that fluid injection has the potential to induce earthquakes—from microseismicity to large, damaging events—by altering state-of-stress conditions in the subsurface. While induced seismicity has not been a major operational issue for carbon storage projects to date, a seismicity hazard exists and must be carefully addressed. Two essential components of effective seismic risk management are (1) sensitive microseismic monitoring and (2) robust data interpretation tools. This report describes a novel workflow, based on advanced processing algorithms applied to microseismic data, to help improve management of seismic risk. This workflow has three main goals: (1) to improve the resolution and reliability of passive seismic monitoring, (2) to extract additional, valuable information from continuous waveform data that is often ignored in standard processing, and (3) to minimize the turn-around time between data collection, interpretation, and decision-making. These three objectives can allow for a better-informed and rapid response to changing subsurface conditions.

Air-coupled seismic waves at long range from Apollo launchings.

Science.gov (United States)

Donn, W. L.; Dalins, I.; Mccarty, V.; Ewing, M.; Kaschak , G.

1971-01-01

Microphones and seismographs were co-located in arrays on Skidaway Island, Georgia, for the launchings of Apollo 13 and 14, 374 km to the south. Simultaneous acoustic and seismic waves were recorded for both events at times appropriate to the arrival of the acoustic waves from the source. The acoustic signal is relatively broadband compared to the nearly monochromatic seismic signal; the seismic signal is much more continuous than the more pulse-like acoustic signal; ground loading from the pressure variations of the acoustic waves is shown to be too small to account for the seismic waves; and the measured phase velocities of both acoustic and seismic waves across the local instrument arrays differ by less than 6 per cent and possibly 3 per cent if experimental error is included. It is concluded that the seismic waves are generated by resonant coupling to the acoustic waves along some 10 km of path on Skidaway Island.

Seismic performance assessment of base-isolated safety-related nuclear structures

Science.gov (United States)

Huang, Y.-N.; Whittaker, A.S.; Luco, N.

2010-01-01

Seismic or base isolation is a proven technology for reducing the effects of earthquake shaking on buildings, bridges and infrastructure. The benefit of base isolation has been presented in terms of reduced accelerations and drifts on superstructure components but never quantified in terms of either a percentage reduction in seismic loss (or percentage increase in safety) or the probability of an unacceptable performance. Herein, we quantify the benefits of base isolation in terms of increased safety (or smaller loss) by comparing the safety of a sample conventional and base-isolated nuclear power plant (NPP) located in the Eastern U.S. Scenario- and time-based assessments are performed using a new methodology. Three base isolation systems are considered, namely, (1) Friction Pendulum??? bearings, (2) lead-rubber bearings and (3) low-damping rubber bearings together with linear viscous dampers. Unacceptable performance is defined by the failure of key secondary systems because these systems represent much of the investment in a new build power plant and ensure the safe operation of the plant. For the scenario-based assessments, the probability of unacceptable performance is computed for an earthquake with a magnitude of 5.3 at a distance 7.5 km from the plant. For the time-based assessments, the annual frequency of unacceptable performance is computed considering all potential earthquakes that may occur. For both assessments, the implementation of base isolation reduces the probability of unacceptable performance by approximately four orders of magnitude for the same NPP superstructure and secondary systems. The increase in NPP construction cost associated with the installation of seismic isolators can be offset by substantially reducing the required seismic strength of secondary components and systems and potentially eliminating the need to seismically qualify many secondary components and systems. ?? 2010 John Wiley & Sons, Ltd.

A Community Seismic Experiment in the ENAM Primary Site

Science.gov (United States)

Van Avendonk, H. J.

2012-12-01

Eastern North America (ENAM) was chosen as a GeoPRISMS Rift Initiation and Evolution primary site because it represents a mature continental margin with onshore and offshore rift basins in which the record of extension and continental break-up is preserved. The degree to which syn-rift magmatism and preexisting lithospheric weaknesses controlled the evolution of the margin can be further investigated if we image its 3-D structure at small and large length scales with active-source and earthquake seismic imaging. In the Summer of 2012 we submitted a proposal to the US National Science Foundation for an ambitious plan for data acquisition on a 400 km wide section of the mid-Atlantic East Coast margin around Cape Hatteras, from unextended continental lithosphere onshore to mature oceanic lithosphere offshore. This area includes an important along-strike transition in the morphology of the margin from the Carolina Trough to the Baltimore Canyon Trough, and two major fracture zones that are associated with significant offsets at the modern Mid-Atlantic Ridge. The study area also covers several features representing the post-rift modification of the margin by slope instability and fluid flow. As the Earthscope Transportable Array reaches the East Coast of the US in 2013 and 2014, we will have an unprecedented opportunity to image the detailed structure of the rifted margin. To make effective use of the research infrastructure, including the seismic vessel R/V Marcus Langseth, the Earthscope seismic instrumentation, and US OBS Instrument Pool, we propose to collect a suite of seismic data at the mid-Atlantic margin in the context of a community-driven experiment with completely open data access. This multi-faceted seismic experiment offers an immense opportunity for education of young scientists. We propose an integrated education effort during and after acquisition. The science and field parties for data acquisition will largely consist of young scientists, who will be

Innovative assesment of the seismic hazard from Vrancea sources

International Nuclear Information System (INIS)

Panza, Giuliano Francesco

2002-01-01

In the framework of a very fruitful, stimulating and still ongoing collaboration between the National Institute for Earth Physics - Bucharest, the Department of Earth Sciences - University of Trieste and The Abdus Salam International Center for Theoretical Physics - SAND Group, several innovative steps forwards have been made in the assessment of the seismic hazard generated by Vrancea seismicity. The limits of currently applied probabilistic approaches are partly overcome by the introduction of hazard scenarios based on the deterministic, realistic modeling of ground motion. The ongoing co-operation represents a fundamental contribution to the reliable assessment of seismic hazard, and has been recently enriched by the participation of Bulgarian scientists, who are facing, in the urban settlements close to the Romanian border, a seismic hazard similar to the one in Bucharest. (author)

Experimental study on radiation resistant properties of seismic isolation elements

International Nuclear Information System (INIS)

Yoneda, G.; Nojima, O.; Aizawa, S.; Uchiyama, Y.; Ikenaga, M.; Yoshizawa, T.

1991-01-01

Recently, studies on the application of a seismic isolation system to a reactor building and or the equipment of a nuclear power plant has been carried out. This study aims at investigating the influence which is exerted upon the mechanical properties of the seismic isolation elements by radiation. The authors conducted irradiation tests, using γ rays, on natural rubber bearings (NRB), lead rubber bearings (LRB), high damping rubber bearings (HRB), and the viscous fluid used in viscous dampers. The maximum radiation intensity was 5 x 10 7 R (Roentgen). The comparison between the mechanical properties of each seismic isolation element before and after the irradiation test are reported in the following. (author)

DFT-based offset-QAM OFDM for optical communications.

Science.gov (United States)

Zhao, Jian

2014-01-13

We experimentally demonstrate and numerically investigate a discrete-Fourier-transform (DFT) based offset quadrature-amplitude-modulation (offset-QAM) orthogonal frequency division multiplexing (OFDM) system. We investigate the scheme using a set of square-root-raised-cosine functions and a set of super-Gaussian functions as signal spectra. It is shown that offset-QAM OFDM exhibits negligible penalty for all investigated spectra, in contrast to rectangular-function based Nyquist FDM (N-FDM) and sinc-function based conventional OFDM (C-OFDM). The required guard interval (GI) length for dispersion compensation in offset-QAM OFDM is analyzed and shown to scale with twice the subcarrier spacing rather than the full OFDM bandwidth. Experimental results show that 38-Gb/s offset-16QAM OFDM supports 600-km fiber transmission with negligible penalty in the absence of GI while a GI length of eight is required in C-OFDM. Further numerical simulations show that by avoiding the GI, 112-Gb/s polarization multiplexed offset-4QAM OFDM can achieve 23% increase in net data rate over C-OFDM under the same transmission reach. We also discuss the design of the pulse-shaping filter in the DFT-based implementation and show that when compared to N-FDM, the required memory length of the filter for pulse shaping can be reduced from 60 to 2 in offset-QAM OFDM regardless of the fiber length.

Reference frame access under the effects of great earthquakes: a least squares collocation approach for non-secular post-seismic evolution

Science.gov (United States)

Gómez, D. D.; Piñón, D. A.; Smalley, R.; Bevis, M.; Cimbaro, S. R.; Lenzano, L. E.; Barón, J.

2016-03-01

The 2010, (Mw 8.8) Maule, Chile, earthquake produced large co-seismic displacements and non-secular, post-seismic deformation, within latitudes 28°S-40°S extending from the Pacific to the Atlantic oceans. Although these effects are easily resolvable by fitting geodetic extended trajectory models (ETM) to continuous GPS (CGPS) time series, the co- and post-seismic deformation cannot be determined at locations without CGPS (e.g., on passive geodetic benchmarks). To estimate the trajectories of passive geodetic benchmarks, we used CGPS time series to fit an ETM that includes the secular South American plate motion and plate boundary deformation, the co-seismic discontinuity, and the non-secular, logarithmic post-seismic transient produced by the earthquake in the Posiciones Geodésicas Argentinas 2007 (POSGAR07) reference frame (RF). We then used least squares collocation (LSC) to model both the background secular inter-seismic and the non-secular post-seismic components of the ETM at the locations without CGPS. We tested the LSC modeled trajectories using campaign and CGPS data that was not used to generate the model and found standard deviations (95 % confidence level) for position estimates for the north and east components of 3.8 and 5.5 mm, respectively, indicating that the model predicts the post-seismic deformation field very well. Finally, we added the co-seismic displacement field, estimated using an elastic finite element model. The final, trajectory model allows accessing the POSGAR07 RF using post-Maule earthquake coordinates within 5 cm for ˜ 91 % of the passive test benchmarks.

Biodiversity offsets and the challenge of achieving no net loss.

Science.gov (United States)

Gardner, Toby A; VON Hase, Amrei; Brownlie, Susie; Ekstrom, Jonathan M M; Pilgrim, John D; Savy, Conrad E; Stephens, R T Theo; Treweek, Jo; Ussher, Graham T; Ward, Gerri; Ten Kate, Kerry

2013-12-01

Businesses, governments, and financial institutions are increasingly adopting a policy of no net loss of biodiversity for development activities. The goal of no net loss is intended to help relieve tension between conservation and development by enabling economic gains to be achieved without concomitant biodiversity losses. biodiversity offsets represent a necessary component of a much broader mitigation strategy for achieving no net loss following prior application of avoidance, minimization, and remediation measures. However, doubts have been raised about the appropriate use of biodiversity offsets. We examined what no net loss means as a desirable conservation outcome and reviewed the conditions that determine whether, and under what circumstances, biodiversity offsets can help achieve such a goal. We propose a conceptual framework to substitute the often ad hoc approaches evident in many biodiversity offset initiatives. The relevance of biodiversity offsets to no net loss rests on 2 fundamental premises. First, offsets are rarely adequate for achieving no net loss of biodiversity alone. Second, some development effects may be too difficult or risky, or even impossible, to offset. To help to deliver no net loss through biodiversity offsets, biodiversity gains must be comparable to losses, be in addition to conservation gains that may have occurred in absence of the offset, and be lasting and protected from risk of failure. Adherence to these conditions requires consideration of the wider landscape context of development and offset activities, timing of offset delivery, measurement of biodiversity, accounting procedures and rule sets used to calculate biodiversity losses and gains and guide offset design, and approaches to managing risk. Adoption of this framework will strengthen the potential for offsets to provide an ecologically defensible mechanism that can help reconcile conservation and development. Balances de Biodiversidad y el Reto de No Obtener P�

How economic contexts shape calculations of yield in biodiversity offsetting.

Science.gov (United States)

Carver, L; Sullivan, S

2017-10-01

We examined and analyzed methods used to create numerical equivalence between sites affected by development and proposed conservation offset sites. Application of biodiversity offsetting metrics in development impact and mitigation assessments is thought to standardize biodiversity conservation outcomes, sometimes termed yield by those conducting these calculations. The youth of biodiversity offsetting in application, however, means little is known about how biodiversity valuations and offset contracts between development and offset sites are agreed on in practice or about long-term conservation outcomes. We examined how sites were made commensurable and how biodiversity gains or yields were calculated and negotiated for a specific offset contract in a government-led pilot study of biodiversity offsets in England. Over 24 months, we conducted participant observations of various stages in the negotiation of offset contracts through repeated visits to 3 (anonymized) biodiversity offset contract sites. We conducted 50 semistructured interviews of stakeholders in regional and local government, the private sector, and civil society. We used a qualitative data analysis software program (DEDOOSE) to textually analyze interview transcriptions. We also compared successive iterations of biodiversity-offsetting calculation spreadsheets and planning documents. A particular focus was the different iterations of a specific biodiversity impact assessment in which the biodiversity offsetting metric developed by the U.K.'s Department for Environment, Food and Rural Affairs was used. We highlight 3 main findings. First, biodiversity offsetting metrics were amended in creative ways as users adapted inputs to metric calculations to balance and negotiate conflicting requirements. Second, the practice of making different habitats equivalent to each other through the application of biodiversity offsetting metrics resulted in commensuration outcomes that may not provide projected

Development of 3-axis precise positioning seismic physical modeling system in the simulation of marine seismic exploration

Science.gov (United States)

Kim, D.; Shin, S.; Ha, J.; Lee, D.; Lim, Y.; Chung, W.

2017-12-01

Seismic physical modeling is a laboratory-scale experiment that deals with the actual and physical phenomena that may occur in the field. In seismic physical modeling, field conditions are downscaled and used. For this reason, even a small error may lead to a big error in an actual field. Accordingly, the positions of the source and the receiver must be precisely controlled in scale modeling. In this study, we have developed a seismic physical modeling system capable of precisely controlling the 3-axis position. For automatic and precise position control of an ultrasonic transducer(source and receiver) in the directions of the three axes(x, y, and z), a motor was mounted on each of the three axes. The motor can automatically and precisely control the positions with positional precision of 2''; for the x and y axes and 0.05 mm for the z axis. As it can automatically and precisely control the positions in the directions of the three axes, it has an advantage in that simulations can be carried out using the latest exploration techniques, such as OBS and Broadband Seismic. For the signal generation section, a waveform generator that can produce a maximum of two sources was used, and for the data acquisition section, which receives and stores reflected signals, an A/D converter that can receive a maximum of four signals was used. As multiple sources and receivers could be used at the same time, the system was set up in such a way that diverse exploration methods, such as single channel, multichannel, and 3-D exploration, could be realized. A computer control program based on LabVIEW was created, so that it could control the position of the transducer, determine the data acquisition parameters, and check the exploration data and progress in real time. A marine environment was simulated using a water tank 1 m wide, 1 m long, and 0.9 m high. To evaluate the performance and applicability of the seismic physical modeling system developed in this study, single channel and

5 CFR 179.213 - Coordinating salary offset with other agencies.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Coordinating salary offset with other... REGULATIONS CLAIMS COLLECTION STANDARDS Salary Offset § 179.213 Coordinating salary offset with other agencies... intent of this regulation. (2) The designated salary offset coordinator will be responsible for: (i...

The Effect of Allowing Pollution Offsets with Imperfect Enforcement

OpenAIRE

Hilary Sigman; Howard F. Chang

2011-01-01

Public policies for pollution control, including climate change policies, sometimes allow polluters in one sector subject to an emissions cap to offset excessive emissions in that sector with pollution abatement in another sector. The government may often find it more costly to verify offset claims than to verify compliance with emissions caps. Concerns about such difficulties in enforcement may lead regulators to restrict the use of offsets. In this paper, we demonstrate that allowing offset...

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 5B. Experience data. Working material

International Nuclear Information System (INIS)

1996-01-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports on the effects of Armenia earthquakes on selected power, industry and commercial facilities and seismic functional qualification of active mechanical and electrical components tested on shaking table

Multiple attenuation to reflection seismic data using Radon filter and Wave Equation Multiple Rejection (WEMR) method

Energy Technology Data Exchange (ETDEWEB)

Erlangga, Mokhammad Puput [Geophysical Engineering, Institut Teknologi Bandung, Ganesha Street no.10 Basic Science B Buliding fl.2-3 Bandung, 40132, West Java Indonesia puput.erlangga@gmail.com (Indonesia)

2015-04-16

Separation between signal and noise, incoherent or coherent, is important in seismic data processing. Although we have processed the seismic data, the coherent noise is still mixing with the primary signal. Multiple reflections are a kind of coherent noise. In this research, we processed seismic data to attenuate multiple reflections in the both synthetic and real seismic data of Mentawai. There are several methods to attenuate multiple reflection, one of them is Radon filter method that discriminates between primary reflection and multiple reflection in the τ-p domain based on move out difference between primary reflection and multiple reflection. However, in case where the move out difference is too small, the Radon filter method is not enough to attenuate the multiple reflections. The Radon filter also produces the artifacts on the gathers data. Except the Radon filter method, we also use the Wave Equation Multiple Elimination (WEMR) method to attenuate the long period multiple reflection. The WEMR method can attenuate the long period multiple reflection based on wave equation inversion. Refer to the inversion of wave equation and the magnitude of the seismic wave amplitude that observed on the free surface, we get the water bottom reflectivity which is used to eliminate the multiple reflections. The WEMR method does not depend on the move out difference to attenuate the long period multiple reflection. Therefore, the WEMR method can be applied to the seismic data which has small move out difference as the Mentawai seismic data. The small move out difference on the Mentawai seismic data is caused by the restrictiveness of far offset, which is only 705 meter. We compared the real free multiple stacking data after processing with Radon filter and WEMR process. The conclusion is the WEMR method can more attenuate the long period multiple reflection than the Radon filter method on the real (Mentawai) seismic data.

Seismic Fracture Characterization Methodologies for Enhanced Geothermal Systems

Energy Technology Data Exchange (ETDEWEB)

Queen, John H. [Hi-Geophysical, Inc., Ponca, OK (United States)

2016-05-09

effective seismic tools for getting information on the internal structure of faults and fractures in support of fluid flow pathway management and EGS treatment. Scattered events similar to those expected from faults and fractures are seen in the VSP reported here. Unfortunately, the source offset and well depth coverage do not allow for detailed analysis of these events. This limited coverage also precluded the use of advanced migration and imaging algorithms. More extensive acquisition is needed to support fault and fracture characterization in the geothermal reservoir at Brady's Hot Springs. The VSP was effective in generating interval velocity estimates over the depths covered by the array. Upgoing reflection events are also visible in the VSP results at locations corresponding to reflection events in the surface seismic. Overall, the high temperature rated fiber optic sensors used in the VSP produced useful results. Modeling has been found useful in the interpretation of both surface reflection seismic and VSP data. It has helped identify possible near surface scattering in the surface seismic data. It has highlighted potential scattering events from deeper faults in the VSP data. Inclusion of more detailed fault and fracture specific stiffness parameters are needed to fully interpret fault and fracture scattered events for flow properties (Pyrak-Nolte and Morris, 2000, Zhu and Snieder, 2002). Shear wave methods were applied in both the surface seismic reflection and VSP work. They were not found to be effective in the Brady's Hot Springs area. This was due to the extreme attenuation of shear waves in the near surface at Brady's. This does not imply that they will be ineffective in general. In geothermal areas where good shear waves can be recorded, modeling suggests they should be very useful for characterizing faults and fractures.

Intensity Based Seismic Hazard Map of Republic of Macedonia

Science.gov (United States)

Dojcinovski, Dragi; Dimiskovska, Biserka; Stojmanovska, Marta

2016-04-01

The territory of the Republic of Macedonia and the border terrains are among the most seismically active parts of the Balkan Peninsula belonging to the Mediterranean-Trans-Asian seismic belt. The seismological data on the R. Macedonia from the past 16 centuries point to occurrence of very strong catastrophic earthquakes. The hypocenters of the occurred earthquakes are located above the Mohorovicic discontinuity, most frequently, at a depth of 10-20 km. Accurate short -term prognosis of earthquake occurrence, i.e., simultaneous prognosis of time, place and intensity of their occurrence is still not possible. The present methods of seismic zoning have advanced to such an extent that it is with a great probability that they enable efficient protection against earthquake effects. The seismic hazard maps of the Republic of Macedonia are the result of analysis and synthesis of data from seismological, seismotectonic and other corresponding investigations necessary for definition of the expected level of seismic hazard for certain time periods. These should be amended, from time to time, with new data and scientific knowledge. The elaboration of this map does not completely solve all issues related to earthquakes, but it provides basic empirical data necessary for updating the existing regulations for construction of engineering structures in seismically active areas regulated by legal regulations and technical norms whose constituent part is the seismic hazard map. The map has been elaborated based on complex seismological and geophysical investigations of the considered area and synthesis of the results from these investigations. There were two phases of elaboration of the map. In the first phase, the map of focal zones characterized by maximum magnitudes of possible earthquakes has been elaborated. In the second phase, the intensities of expected earthquakes have been computed according to the MCS scale. The map is prognostic, i.e., it provides assessment of the

Offset Compound Gear Drive

Science.gov (United States)

Stevens, Mark A.; Handschuh, Robert F.; Lewicki, David G.

2010-01-01

The Offset Compound Gear Drive is an in-line, discrete, two-speed device utilizing a special offset compound gear that has both an internal tooth configuration on the input end and external tooth configuration on the output end, thus allowing it to mesh in series, simultaneously, with both a smaller external tooth input gear and a larger internal tooth output gear. This unique geometry and offset axis permits the compound gear to mesh with the smaller diameter input gear and the larger diameter output gear, both of which are on the same central, or primary, centerline. This configuration results in a compact in-line reduction gear set consisting of fewer gears and bearings than a conventional planetary gear train. Switching between the two output ratios is accomplished through a main control clutch and sprag. Power flow to the above is transmitted through concentric power paths. Low-speed operation is accomplished in two meshes. For the purpose of illustrating the low-speed output operation, the following example pitch diameters are given. A 5.0 pitch diameter (PD) input gear to 7.50 PD (internal tooth) intermediate gear (0.667 reduction mesh), and a 7.50 PD (external tooth) intermediate gear to a 10.00 PD output gear (0.750 reduction mesh). Note that it is not required that the intermediate gears on the offset axis be of the same diameter. For this example, the resultant low-speed ratio is 2:1 (output speed = 0.500; product of stage one 0.667 reduction and stage two 0.750 stage reduction). The design is not restricted to the example pitch diameters, or output ratio. From the output gear, power is transmitted through a hollow drive shaft, which, in turn, drives a sprag during which time the main clutch is disengaged.

Seismic assessment of a site using the time series method

International Nuclear Information System (INIS)

Krutzik, N.J.; Rotaru, I.; Bobei, M.; Mingiuc, C.; Serban, V.; Androne, M.

1997-01-01

To increase the safety of a NPP located on a seismic site, the seismic acceleration level to which the NPP should be qualified must be as representative as possible for that site, with a conservative degree of safety but not too exaggerated. The consideration of the seismic events affecting the site as independent events and the use of statistic methods to define some safety levels with very low annual occurrence probability (10 -4 ) may lead to some exaggerations of the seismic safety level. The use of some very high value for the seismic acceleration imposed by the seismic safety levels required by the hazard analysis may lead to very costly technical solutions that can make the plant operation more difficult and increase maintenance costs. The considerations of seismic events as a time series with dependence among the events produced, may lead to a more representative assessment of a NPP site seismic activity and consequently to a prognosis on the seismic level values to which the NPP would be ensured throughout its life-span. That prognosis should consider the actual seismic activity (including small earthquakes in real time) of the focuses that affect the plant site. The paper proposes the applications of Autoregressive Time Series to issue a prognosis on the seismic activity of a focus and presents the analysis on Vrancea focus that affects NPP Cernavoda site, by this method. The paper also presents the manner to analyse the focus activity as per the new approach and it assesses the maximum seismic acceleration that may affect NPP Cernavoda throughout its life-span (∼ 30 years). Development and applications of new mathematical analysis method, both for long - and short - time intervals, may lead to important contributions in the process of foretelling the seismic events in the future. (authors)

12 CFR 313.49 - Coordinating salary offset with other agencies.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Coordinating salary offset with other agencies... PRACTICE PROCEDURES FOR CORPORATE DEBT COLLECTION Salary Offset § 313.49 Coordinating salary offset with... employee has consented to the salary offset in writing or has signed a statement acknowledging receipt of...

Seismic analysis of axisymmetric shells

International Nuclear Information System (INIS)

Jospin, R.J.; Toledo, E.M.; Feijoo, R.A.

1984-01-01

Axisymmetric shells subjected to multiple support excitation are studied. The shells are spatialy discretized by the finite element method and in order to obtain estimates for the maximum values of displacements and stresses the response spectrum tecnique is used. Finally, some numerical results are presented and discussed in the case of a shell of revolution with vertical symmetry axis, subjected to seismic ground motions in the horizontal, vertical and rocking directions. (Author) [pt

Seismic Analysis of Concrete Dam by Using Finite Element Method

Directory of Open Access Journals (Sweden)

Rozaina Ismail

2017-01-01

Full Text Available This paper reports a brief study on linear seismic analysis of Sg. Kinta Concrete Dam. The analysis was conducted in order to determine the performance and behaviour of the dam under seismic excitation. The dam was modelled as two-dimensional and developed based on the design drawing that is obtained from Angkasa Consulting Services Sdn. Bhd. The seismic analysis of the dam is conducted using finite element analysis software package LUSAS 14.3 and the dam has been analyse as a plain stress problem with a linear consideration. A set of historic data, with E1 Centro earthquake acceleration of about 0.50g is used as an earthquake excitation. The natural frequency and mode shape up to fifth mode of the dam has been obtained from the analysis to show the differences of the stress and deformation between each mode. The maximum horizontal and vertical stress of Sg. Kinta dam was found and the distribution of them was discussed in form of contours. The deformation of the dam were also been discussed by comparing the maximum displacement for each mode shaped.

Factors affecting seismic response of submarine slopes

Directory of Open Access Journals (Sweden)

G. Biscontin

2006-01-01

Full Text Available The response of submerged slopes on the continental shelf to seismic or storm loading has become an important element in the risk assessment for offshore structures and 'local' tsunami hazards worldwide. The geological profile of these slopes typically includes normally consolidated to lightly overconsolidated soft cohesive soils with layer thickness ranging from a few meters to hundreds of meters. The factor of safety obtained from pseudo-static analyses is not always a useful measure for evaluating the slope response, since values less than one do not necessarily imply slope failure with large movements of the soil mass. This paper addresses the relative importance of different factors affecting the response of submerged slopes during seismic loading. The analyses use a dynamic finite element code which includes a constitutive law describing the anisotropic stress-strain-strength behavior of normally consolidated to lightly overconsolidated clays. The model also incorporates anisotropic hardening to describe the effect of different shear strain and stress histories as well as bounding surface principles to provide realistic descriptions of the accumulation of the plastic strains and excess pore pressure during successive loading cycles. The paper presents results from parametric site response analyses on slope geometry and layering, soil material parameters, and input ground motion characteristics. The predicted maximum shear strains, permanent deformations, displacement time histories and maximum excess pore pressure development provide insight of slope performance during a seismic event.

Maximum magnitude of injection-induced earthquakes: A criterion to assess the influence of pressure migration along faults

Science.gov (United States)

Norbeck, Jack H.; Horne, Roland N.

2018-05-01

The maximum expected earthquake magnitude is an important parameter in seismic hazard and risk analysis because of its strong influence on ground motion. In the context of injection-induced seismicity, the processes that control how large an earthquake will grow may be influenced by operational factors under engineering control as well as natural tectonic factors. Determining the relative influence of these effects on maximum magnitude will impact the design and implementation of induced seismicity management strategies. In this work, we apply a numerical model that considers the coupled interactions of fluid flow in faulted porous media and quasidynamic elasticity to investigate the earthquake nucleation, rupture, and arrest processes for cases of induced seismicity. We find that under certain conditions, earthquake ruptures are confined to a pressurized region along the fault with a length-scale that is set by injection operations. However, earthquakes are sometimes able to propagate as sustained ruptures outside of the zone that experienced a pressure perturbation. We propose a faulting criterion that depends primarily on the state of stress and the earthquake stress drop to characterize the transition between pressure-constrained and runaway rupture behavior.

Quadrupole to BPM offset determination in Indus-2

International Nuclear Information System (INIS)

Jena, Saroj; Ghodke, A.D.; Singh, G.

2009-01-01

A feasibility of finding the quadrupole to BPM offset using beam based alignment (BBA) technique in Indus-2 has been studied. The measurements of the offsets between BPM and quadrupoles could be performed by using quadratic fitting for the minima of the orbit response w. r. t. changes in the quadrupole strengths. These offsets will be integrated to the orbit data during closed orbit correction. There are 72 quadrupoles and 56 BPMs in Indus-2. However the assessment of Quad-BPM offsets is not feasible in some cases due to non-availability of BPM adjacent to quadrupole and also in some cases because of a large phase advance between quadrupole and nearby BPM. Here single corrector method is used to obtain these offsets and assumed the current of each quadrupole can be varied independently. A graphical user interface (GUI) is developed in MATLAB for the use of BBA in Indus-2. (author)

Detailed seismicity analysis in the SE of Romania (Dobrogea region)

Science.gov (United States)

Rogozea, Maria; Radulian, Mircea; Ghica, Daniela; Popa, Mihaela

2014-05-01

The purpose of this paper is to analyze the seismicity in the south-eastern part of Romania, in the Dobrogea region (namely the Predobrogean Depression and Black Sea area). Predobrogean Depression is the name attributed to the structures belonging to the Scythian Platform. The seismic activity is moderate with most significant earthquakes at the boundary between the North Dobrogea Orogen and Scythian Platform (Sf. Gheorghe fault). The largest magnitude event was recorded in 02.11.1871 (Mw = 5.3). Other events with magnitude above 4 were observed close to Tulcea city (13.11.1981, Mw = 5.1, 03.09.204, Mw =5.1) and Galati city (11.09.1980, Mw = 4.2). Recently, an earthquake swarm of 406 events extended over two months and a half (23 September - 5 December 2013) was produced in the Galati area (maximum magnitude 3.9). The deformation field has an extensional regime, as resulted from fault plane solutions and geotectonic investigations. The maximum expected magnitude in this area is estimated at Mw = 5.5. The seismic activity in the Black Sea area, close to Romania seashore and north-east Bulgarian seashore, concentrates along Shabla fault system. Large shocks (magnitude above 7) are reported here at intervals of a few centuries. The most recent major shock was recorded on 31 January 1901 (Mw = 7.2) in Shabla region, Bulgaria. To characterize seismicity parameters, the Romanian catalogue of the National Institute of Earth Physics was used as a basic input. The catalogue was revised as concerns historical information by reanalyzing macroseismic data and for the recent events, by applying up-to-date tools to relocate and re-parametrize the seismic sources.

15 CFR 19.10 - How will Commerce entities use administrative offset (offset of non-tax Federal payments) to...

Science.gov (United States)

2010-01-01

... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false How will Commerce entities use administrative offset (offset of non-tax Federal payments) to collect a Commerce debt? 19.10 Section 19.10 Commerce and Foreign Trade Office of the Secretary of Commerce COMMERCE DEBT COLLECTION Procedures To...

An Expedient but Fascinating Geophysical Chimera: The Pinyon Flat Seismic Strain Point Array

Science.gov (United States)

Langston, C. A.

2016-12-01

The combination of a borehole Gladwin Tensor Strain Meter (GTSM) and a co-located three component broadband seismometer (BB) can theoretically be used to determine the propagation attributes of P-SV waves in vertically inhomogeneous media such as horizontal phase velocity and azimuth of propagation through application of wave gradiometry. A major requirement for this to be successful is to have well-calibrated strain and seismic sensors to be able to rely on using absolute wave amplitude from both systems. A "point" seismic array is constructed using the PBO GTSM station B084 and co-located BB seismic stations from an open array experiment deployed by UCSD as well as PFO station at the Pinyon Flat facility. Site amplitude statics for all three ground motion components are found for the 14-element (13 PY stations + PFO), small aperture seismic array using data from 47 teleseisms recorded from 2014 until present. Precision of amplitude measurement at each site is better than 0.2% for vertical components, 0.5% for EW components, and 1% for NS components. Relative amplitudes among sites of the array are often better than 1% attesting to the high quality of the instrumentation and installation. The wavefield and related horizontal strains are computed for the location of B084 using a second order Taylor's expansion of observed waveforms from moderate ( M4) regional events. The computed seismic array areal, differential, and shear strains show excellent correlation in both phase and amplitude with those recorded by B084 when using the calibration matrix previously determined using teleseismic strains from the entire ANZA seismic network. Use of the GTSM-BB "point" array significantly extends the bandwidth of gradiometry calculations over the small-aperture seismic array by nearly two orders of magnitude from 0.5 Hz to 0.01 Hz. In principle, a seismic strain point array could be constructed from every PBO GTSM with a co-located seismometer to help serve earthquake early

Precursory diffuse CO2 emission signature of the 2011 El Hierro submarine eruption, Canary Islands

Science.gov (United States)

Pérez, N. M.; Padilla, G. D.; Padrón, E.; Hernández, P. A.; Melián, G. V.; Barrancos, J.; Dionis, S.; Rodríguez, F.; Nolasco, D.; Calvo, D.; Hernández, I.; Peraza, M. D.

2012-04-01

are measured 40-cm deep, and recorded contemporaneously with CO2 efflux. Although time series of CO2 efflux showed background (4-5 g m-2 d-1) values before the July 16, when the seismic unrest started, and still August 30, some significant increases up to 10 g m-2 d-1 was measured prior the occurrence of peaks on the seismic energy release. Since the end of August, coinciding with a migration of the hypocenters of the seismic activity toward the south part of the island, the CO2 efflux time series started a relatively constant increase during 1 month, reaching a maximum of 19 g m-2 d-1 one week before the occurrence of the submarine volcanic eruption. Since October 5 till present, including the whole eruptive period, the CO2 efflux time series have shown a general decrease trend but with some significant emission peaks prior the occurrence of important seismic energy release episodes. This station has revealed as an important observation point to evaluate the volcanic activity of El Hierro Island since diffuse degassing of carbon dioxide seems to be associated with fluid pressure fluctuations in the volcanic system. These results demonstrated the potential of applying continuous monitoring of soil CO2 efflux to improve and optimize the detection of early warning signals of future volcanic unrest episodes at El Hierro.

Offset Trace-Based Video Quality Evaluation Network Transport

DEFF Research Database (Denmark)

Seeling, P.; Reisslein, M.; Fitzek, Frank

2006-01-01

Video traces contain information about encoded video frames, such as frame sizes and qualities, and provide a convenient method to conduct multimedia networking research. Although wiedely used in networking research, these traces do not allow to determine the video qaulityin an accurate manner...... after networking transport that includes losses and delays. In this work, we provide (i) an overview of frame dependencies that have to be taken into consideration when working with video traces, (ii) an algorithmic approach to combine traditional video traces and offset distortion traces to determine...... the video quality or distortion after lossy network transport, (iii) offset distortion and quality characteristics and (iv) the offset distortion trace format and tools to create offset distortion traces....

Prospects for international trade in environmental services: An analysis of international carbon emission off-sets

International Nuclear Information System (INIS)

Swisher, J.N.

1991-01-01

This dissertation presents a case study analysis in which the costs to a US electric utility of reducing its carbon dioxide (CO 2 ) emissions are compared with the costs of carbon-saving forestry projects in Costa Rica and Guatemala. The results show that a large electric utility in the south-central US would find it relatively inexpensive, even profitable given a conducive regulatory treatment, to reduce its CO 2 emissions by a few percent over the next ten years, through direct investment in energy end-use efficiency improvements. In comparison, the costs of the forestry projects studied in Central America range from $1/TC to a worst-case value of about $55/TC, with most project costs between $5 and $13/TC, depending on the type of project, the climate, and the opportunity cost of land. The total amount of CO 2 storage potential is significant, about 100 million tons per country, but not enough to suggest that forestry can offset more than a few percent of global CO 2 emissions from fossil fuel use. These case studies suggest that international trade in the environmental service of reducing global CO 2 accumulation could have significant economic and ecological benefits. A transaction in which a utility pays for forestry projects in exchange for credit against an emission reduction policy is an example of an international carbon emission offset (ICEO). ICEO's could provide a currency for funding carbon-saving services as a way to comply with national policies to reduce CO 2 emissions, as long as compliance is allowed through investments in other countries. This type of North-South transfer is necessary to reconcile economic efficiency and international equity, because of the disparity between the national allocations of responsibility for greenhouse gas emissions and opportunities for emission reductions

Seismic reflection surveys in central Palo Duro basin

International Nuclear Information System (INIS)

Acharya, H.; Buller, M.L.; Lewkowicz, J.; Murphy, P.

1983-01-01

Seismic reflection surveys have been conducted in the central Palo Duro basin to provide a basis for identifying localities suitable for the emplacement of an underground high level nuclear waste repository. The objectives of this effort were to determine the structure and stratigraphy in the central Palo Duro basin and evaluate the potential for hydrocarbon resources. Of primary interest is the Upper Permian salt section to a depth of about 3000 ft (914 m). Various tests were carried out along a 3 mi (5 km) segment to determine the most appropriate combination of vibrating source and recording parameters. Approximately 130 mi (209 km) of 24-fold CDP stacked data were acquired. The survey lines were tied to test wells in which velocity surveys were conducted. These data were supplemented by about 400 mi (644 km) of available proprietary CDP stacked data. Analysis of these data strongly suggests that central Palo Duro basin has been tectonically stable since Early Permian time. The maximum offset of the basement is about 600 ft (183 m). These basement faults do not appear to affect any strata above. The San Andres Formation and underlying formations can be traced continuously throughout the area surveyed. Available velocity data from various wells in the central Palo Duro basin show few anomalies, confirming the continuity of the reflecting horizons and the tectonic stability of the area. Hydrocarbon potential of the area is presently being evaluated. The preliminary results of this study are in agreement with the stratigraphic correlations among well logs in the Palo Duro basin

Influence of joint dip angle on seismic behaviors of rock foundation

International Nuclear Information System (INIS)

Yang, Lei; Gao, Yang; Jiang, Yujing; Li, Bo; Li Shucai

2012-01-01

The seismic response of rock foundation to seismic loads is an important issue to the stability and safety of nuclear power plants. Due to the fact that the discontinuities like joints existing in the rock mass govern principally the deformation and failure behaviors of the rock mass, the influence of discontinuities on the seismic behaviors of rock mass remains as one of the fundamental problems in the safety assessment of nuclear power plants. In this study, the distinct element method (DEM) and finite element method (FEM) were adopted to investigate the seismic responses of rock foundation to a real seismic wave, taking into account the effect of joint dip angle on the deformation and dynamic behaviors of rock foundation. In the DEM simulations, the intact rock has an amplification effect on the amplitudes of seismic waves, while the joints exhibit an attenuation effect on the seismic waves. In the FEM simulations, however, the attenuation effect of joints is not obvious. The dip angle of joints has strong effects on the deformation and dynamic behaviors of rock foundation, in terms that different dip angles lead to obviously different deformation and horizontal stress in the rock foundation when subjected to seismic load. When the dip angle of joints is around 60deg, the seismic velocity, displacement and stress reach the maximums. Therefore, attentions need to be paid on this factor during the seismic design of nuclear power plants. (author)

Estimating seismic moment magnitude (Mw) of tremor bursts in northern Cascadia: Implications for the “seismic efficiency” of episodic tremor and slip

Science.gov (United States)

Kao, Honn; Wang, Kelin; Dragert, Herb; Kao, Jason Y.; Rogers, Garry

2010-10-01

We develop a method to estimate the seismic moments of deep non-volcanic tremor bursts observed in northern Cascadia. For each tremor burst, the maximum amplitudes at individual stations within a time window ±5 s around the predicted arrivals of the S phase are measured and compared to the maximum S amplitudes measured from synthetic seismograms. The proposed method is thoroughly calibrated using 464 local earthquakes and the results show excellent consistency between the reported ML and the estimated Mw. We apply the method to northern Cascadia tremors and infer that most bursts have Mw˜1.0-1.7. The corresponding b value appears to be 1, consistent with that of ordinary earthquakes but over a narrower Mw range. Comparison of cumulative tremor Mw and the Mw estimated from the accompanying slow slip suggests that the “seismic efficiency” of the Episodic Tremor and Slip (ETS) is of the order of 0.1% or less.

10 CFR 16.15 - Procedures for internal salary offset.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Procedures for internal salary offset. 16.15 Section 16.15 Energy NUCLEAR REGULATORY COMMISSION SALARY OFFSET PROCEDURES FOR COLLECTING DEBTS OWED BY FEDERAL EMPLOYEES TO THE FEDERAL GOVERNMENT § 16.15 Procedures for internal salary offset. (a) Deductions to...

Maximum temperature accounts for annual soil CO2 efflux in temperate forests of Northern China

Science.gov (United States)

Zhou, Zhiyong; Xu, Meili; Kang, Fengfeng; Jianxin Sun, Osbert

2015-01-01

It will help understand the representation legality of soil temperature to explore the correlations of soil respiration with variant properties of soil temperature. Soil temperature at 10 cm depth was hourly logged through twelve months. Basing on the measured soil temperature, soil respiration at different temporal scales were calculated using empirical functions for temperate forests. On monthly scale, soil respiration significantly correlated with maximum, minimum, mean and accumulated effective soil temperatures. Annual soil respiration varied from 409 g C m−2 in coniferous forest to 570 g C m−2 in mixed forest and to 692 g C m−2 in broadleaved forest, and was markedly explained by mean soil temperatures of the warmest day, July and summer, separately. These three soil temperatures reflected the maximum values on diurnal, monthly and annual scales. In accordance with their higher temperatures, summer soil respiration accounted for 51% of annual soil respiration across forest types, and broadleaved forest also had higher soil organic carbon content (SOC) and soil microbial biomass carbon content (SMBC), but a lower contribution of SMBC to SOC. This added proof to the findings that maximum soil temperature may accelerate the transformation of SOC to CO2-C via stimulating activities of soil microorganisms. PMID:26179467

Poisson's ratio model derived from P- and S-wave reflection seismic data at the CO2CRC Otway Project pilot site, Australia

Science.gov (United States)

Beilecke, Thies; Krawczyk, Charlotte M.; Tanner, David C.; Ziesch, Jennifer; Research Group Protect

2014-05-01

Compressional wave (P-wave) reflection seismic field measurements are a standard tool for subsurface exploration. 2-D seismic measurements are often used for overview measurements, but also as near-surface supplement to fill gaps that often exist in 3-D seismic data sets. Such supplementing 2-D measurements are typically simple with respect to field layout. This is an opportunity for the use of shear waves (S-waves). Within the last years, S-waves have become more and more important. One reason is that P- and S-waves are differently sensitive to fluids and pore fill so that the additional S-wave information can be used to enhance lithological studies. Another reason is that S-waves have the advantage of higher spatial resolution. Within the same signal bandwidth they typically have about half the wavelength of P-waves. In near-surface unconsolidated sediments they can even enhance the structural resolution by one order of magnitude. We make use of these capabilities within the PROTECT project. In addition to already existing 2-D P-wave data, we carried out a near surface 2-D S-wave field survey at the CO2CRC Otway Project pilot site, close to Warrnambool, Australia in November 2013. The combined analysis of P-wave and S-wave data is used to construct a Poisson's Ratio 2-D model down to roughly 600 m depth. The Poisson's ratio values along a 1 km long profile at the site are surprisingly high, ranging from 0.47 in the carbonate-dominated near surface to 0.4 at depth. In the literature, average lab measurements of 0.22 for unfissured carbonates and 0.37 for fissured examples have been reported. The high values that we found may indicate areas of rather unconsolidated or fractured material, or enhanced fluid contents, and will be subject of further studies. This work is integrated in a larger workflow towards prediction of CO2 leakage and monitoring strategies for subsurface storage in general. Acknowledgement: This work was sponsored in part by the Australian

Optimizing the design of vertical seismic profiling (VSP) for imaging fracture zones over hardrock basement geothermal environments

Science.gov (United States)

Reiser, Fabienne; Schmelzbach, Cedric; Maurer, Hansruedi; Greenhalgh, Stewart; Hellwig, Olaf

2017-04-01

A primary focus of geothermal seismic imaging is to map dipping faults and fracture zones that control rock permeability and fluid flow. Vertical seismic profiling (VSP) is therefore a most valuable means to image the immediate surroundings of an existing borehole to guide, for example, the placing of new boreholes to optimize production from known faults and fractures. We simulated 2D and 3D acoustic synthetic seismic data and processed it through to pre-stack depth migration to optimize VSP survey layouts for mapping moderately to steeply dipping fracture zones within possible basement geothermal reservoirs. Our VSP survey optimization procedure for sequentially selecting source locations to define the area where source points are best located for optimal imaging makes use of a cross-correlation statistic, by which a subset of migrated shot gathers is compared with a target or reference image from a comprehensive set of source gathers. In geothermal exploration at established sites, it is reasonable to assume that sufficient à priori information is available to construct such a target image. We generally obtained good results with a relatively small number of optimally chosen source positions distributed over an ideal source location area for different fracture zone scenarios (different dips, azimuths, and distances from the surveying borehole). Adding further sources outside the optimal source area did not necessarily improve the results, but rather resulted in image distortions. It was found that fracture zones located at borehole-receiver depths and laterally offset from the borehole by 300 m can be imaged reliably for a range of the different dips, but more source positions and large offsets between sources and the borehole are required for imaging steeply dipping interfaces. When such features cross-cut the borehole, they are particularly difficult to image. For fracture zones with different azimuths, 3D effects are observed. Far offset source positions

Syntectonic Mississippi River Channel Response: Integrating River Morphology and Seismic Imaging to Detect Active Faults

Science.gov (United States)

Magnani, M. B.

2017-12-01

Alluvial rivers, even great rivers such as the Mississippi, respond to hydrologic and geologic controls. Temporal variations of valley gradient can significantly alter channel morphology, as the river responds syntectonically to attain equilibrium. The river will alter its sinuosity, in an attempt to maintain a constant gradient on a surface that changes slope through time. Therefore, changes of river pattern can be the first clue that active tectonics is affecting an area of pattern change. Here I present geomorphological and seismic imaging evidence of a previously unknown fault crossing the Mississippi river south of the New Madrid seismic zone, between Caruthersville, Missouri and Osceola, Arkansas, and show that both datasets support Holocene fault movement, with the latest slip occurring in the last 200 years. High resolution marine seismic reflection data acquired along the Mississippi river imaged a NW-SE striking north-dipping fault displacing the base of the Quaternary alluvium by 15 m with reverse sense of movement. The fault consistently deforms the Tertiary, Cretaceous and Paleozoic formations. Historical river channel planforms dating back to 1765 reveal that the section of the river channel across the fault has been characterized by high sinuosity and steep projected-channel slope compared to adjacent river reaches. In particular, the reach across the fault experienced a cutoff in 1821, resulting in a temporary lowering of sinuosity followed by an increase between the survey of 1880 and 1915. Under the assumption that the change in sinuosity reflects river response to a valley slope change to maintain constant gradient, I use sinuosity through time to calculate the change in valley slope since 1880 and therefore to estimate the vertical displacement of the imaged fault in the past 200 years. Based on calculations so performed, the vertical offset of the fault is estimated to be 0.4 m, accrued since at least 1880. If the base of the river alluvium

Reflection seismic studies over the end-glacial Burträsk fault, Skellefteå, Sweden

Directory of Open Access Journals (Sweden)

C. Juhlin

2011-01-01

Full Text Available Reflection seismic data were acquired along a ca. 22 km long profile over the end-glacial Burträsk fault with a nominal receiver and source spacing of 20 m. A steeply dipping reflection can be correlated to the Burträsk fault, indicating that the fault dips at about 55° to the southeast near the surface. The reflection from the fault is rather poorly imaged, probably due to a lateral offset in the fault of about 1 km at this location and the crookedness of the seismic profile in the vicinity of the fault. A more pronounced steeply dipping reflection is observed about 4 km southeast of the Burträsk fault. Based on its correlation with a topographic low at the surface this reflection is interpreted to originate from a fracture zone. There are no signs of large displacements along this zone as the glacial ice receded, but earthquakes could be associated with it today. Other reflections on the processed seismic section may originate from changes in lithological variations in the supra-crustal rocks or from intrusions of more mafic rock. Constraints on the fault geometry provided by the reflection seismic data will help determine what stresses were required to activate the fault when the major rupture along it occurred ca. 9500 years ago.

Seismic isolation - efficient procedure for seismic response assessement

International Nuclear Information System (INIS)

Zamfir, M. A.; Androne, M.

2016-01-01

The aim of this analysis is to reduce the dynamic response of a structure. The seismic isolation solution must take into consideration the specific site ground motion. In this paper will be presented results obtained by applying the seismic isolation method. Based on the obtained results, important conclusions can be outlined: the seismic isolation device has the ability to reduce seismic acceleration of the seismic isolated structure to values that no longer present a danger to people and environment; the seismic isolation solution is limiting devices deformations to safety values for ensuring structural integrity and stability of the entire system; the effective seismic energy dissipation and with no side effects both for the seismic isolated building and for the devices used, and the return to the initial position before earthquake occurence are obtained with acceptable permanent displacement. (authors)

Achieving biodiversity benefits with offsets: Research gaps, challenges, and needs.

Science.gov (United States)

Gelcich, Stefan; Vargas, Camila; Carreras, Maria Jose; Castilla, Juan Carlos; Donlan, C Josh

2017-03-01

Biodiversity offsets are becoming increasingly common across a portfolio of settings: national policy, voluntary programs, international lending, and corporate business structures. Given the diversity of ecological, political, and socio-economic systems where offsets may be applied, place-based information is likely to be most useful in designing and implementing offset programs, along with guiding principles that assure best practice. We reviewed the research on biodiversity offsets to explore gaps and needs. While the peer-reviewed literature on offsets is growing rapidly, it is heavily dominated by ecological theory, wetland ecosystems, and U.S.-based research. Given that majority of offset policies and programs are occurring in middle- and low-income countries, the research gaps we identified present a number of risks. They also present an opportunity to create regionally based learning platforms focused on pilot projects and institutional capacity building. Scientific research should diversify, both topically and geographically, in order to support the successful design, implementation, and monitoring of biodiversity offset programs.

A preliminary census of engineering activities located in Sicily (Southern Italy) which may "potentially" induce seismicity

Science.gov (United States)

Aloisi, Marco; Briffa, Emanuela; Cannata, Andrea; Cannavò, Flavio; Gambino, Salvatore; Maiolino, Vincenza; Maugeri, Roberto; Palano, Mimmo; Privitera, Eugenio; Scaltrito, Antonio; Spampinato, Salvatore; Ursino, Andrea; Velardita, Rosanna

2015-04-01

The seismic events caused by human engineering activities are commonly termed as "triggered" and "induced". This class of earthquakes, though characterized by low-to-moderate magnitude, have significant social and economical implications since they occur close to the engineering activity responsible for triggering/inducing them and can be felt by the inhabitants living nearby, and may even produce damage. One of the first well-documented examples of induced seismicity was observed in 1932 in Algeria, when a shallow magnitude 3.0 earthquake occurred close to the Oued Fodda Dam. By the continuous global improvement of seismic monitoring networks, numerous other examples of human-induced earthquakes have been identified. Induced earthquakes occur at shallow depths and are related to a number of human activities, such as fluid injection under high pressure (e.g. waste-water disposal in deep wells, hydrofracturing activities in enhanced geothermal systems and oil recovery, shale-gas fracking, natural and CO2 gas storage), hydrocarbon exploitation, groundwater extraction, deep underground mining, large water impoundments and underground nuclear tests. In Italy, induced/triggered seismicity is suspected to have contributed to the disaster of the Vajont dam in 1963. Despite this suspected case and the presence in the Italian territory of a large amount of engineering activities "capable" of inducing seismicity, no extensive researches on this topic have been conducted to date. Hence, in order to improve knowledge and correctly assess the potential hazard at a specific location in the future, here we started a preliminary study on the entire range of engineering activities currently located in Sicily (Southern Italy) which may "potentially" induce seismicity. To this end, we performed: • a preliminary census of all engineering activities located in the study area by collecting all the useful information coming from available on-line catalogues; • a detailed compilation

Multi-analysis and modeling of asymmetry offset for Hall effect structures

Energy Technology Data Exchange (ETDEWEB)

Paun, Maria-Alexandra, E-mail: maria_paun2003@yahoo.com

2017-03-15

The topological (asymmetry) offset voltage of CMOS cross-like Hall cells is analyzed in this paper. In order to attain the stated objective, different approaches have been considered. Both circuit and three-dimensional models have been developed. Variation of the misalignment offset with the biasing current has been studied through physical and circuit models. The latter is a non-homogenous finite elements model, which relies on using parameterized resistances and current-controlled current sources, of CMOS Hall cells. The displacement offset for various asymmetries and the offset variation with the temperature were investigated through the circuit model developed. Various experimental results for the single and magnetic equivalent offset have also been provided. - Highlights: • In this paper both physical and circuit models have been proposed for the evaluation of Hall cells offset. • Variation of the misalignment offset with the biasing current has been studied. • The displacement offset for various asymmetries and the offset variation with the temperature were investigated. • Various experimental results for single and magnetic equivalent offset were provided. • The obtained simulation results are in accordance with the experimental data.

An intercomparison of the thermal offset for different pyranometers

Science.gov (United States)

Sanchez, G.; Cancillo, M. L.; Serrano, A.

2016-07-01

An unprecedented intensive intercomparison campaign focused on the experimental measurement of the thermal offset of pyranometers has been conducted at Badajoz (Spain) with the participation of three main manufacturers. The purpose of this study is to compare the thermal offset of six commercially available pyranometers, being some of them widely used and others recently commercialized. In this campaign, the capping methodology has been used to experimentally measure the daytime thermal offset of the pyranometers. Thus, a short but intense campaign has been conducted in two selected summer days under clear-sky conditions, covering a large range of solar zenith angle, irradiance, and temperature. Along the campaign, a total of 305 capping events have been performed, 61 for each pyranometer. The daytime thermal offset obtained for different pyranometers ranges between 0 and -16.8 W/m2 depending on the environmental conditions, being sometimes notably higher than values estimated indoors by manufacturers. The thermal offset absolute value of all instruments shows a diurnal cycle, increasing from sunrise to central hours of the day and decreasing from midafternoon to sunset. The analysis demonstrates that thermal offset is notably higher and more variable during daytime than during nighttime, requiring specific daytime measurements. Main results emphasize the key role played by wind speed in modulating the thermal offset.

Simultaneous inversion of seismic velocity and moment tensor using elastic-waveform inversion of microseismic data: Application to the Aneth CO2-EOR field

Science.gov (United States)

Chen, Y.; Huang, L.

2017-12-01

Moment tensors are key parameters for characterizing CO2-injection-induced microseismic events. Elastic-waveform inversion has the potential to providing accurate results of moment tensors. Microseismic waveforms contains information of source moment tensors and the wave propagation velocity along the wavepaths. We develop an elastic-waveform inversion method to jointly invert the seismic velocity model and moment tensor. We first use our adaptive moment-tensor joint inversion method to estimate moment tensors of microseismic events. Our adaptive moment-tensor inversion method jointly inverts multiple microseismic events with similar waveforms within a cluster to reduce inversion uncertainty for microseismic data recorded using a single borehole geophone array. We use this inversion result as the initial model for our elastic-waveform inversion to minimize the cross-correlated-based data misfit between observed data and synthetic data. We verify our method using synthetic microseismic data and obtain improved results of both moment tensors and seismic velocity model. We apply our new inversion method to microseismic data acquired at a CO2-enhanced oil recovery field in Aneth, Utah, using a single borehole geophone array. The results demonstrate that our new inversion method significantly reduces the data misfit compared to the conventional ray-theory-based moment-tensor inversion.

Effect of fault roughness on aftershock distribution and post co-seismic strain accumulation.

Science.gov (United States)

Aslam, K.; Daub, E. G.

2017-12-01

We perform physics-based simulations of earthquake rupture propagation on geometrically complex strike-slip faults. We consider many different realization of the fault roughness and obtain heterogeneous stress fields by performing dynamic rupture simulation of large earthquakes. We calculate the Coulomb failure function (CFF) for all these realizations so that we can quantify zones of stress increase/shadows surrounding the main fault and compare our results to seismic catalogs. To do this comparison, we use relocated earthquake catalogs from Northern and Southern California. We specify the range of fault roughness parameters based on past observational studies. The Hurst exponent (H) varies in range from 0.5 to 1 and RMS height to wavelength ratio ( RMS deviation of a fault profile from planarity) has values between 10-2 to 10-3. For any realization of fault roughness, the Probability density function (PDF) values relative to the mean CFF change show a wider spread near the fault and this spread squeezes into a narrow band as we move away from fault. For lower value of RMS ratio ( 10-3), we see bigger zones of stress change near the hypocenter and for higher value of RMS ratio ( 10-2), we see alternate zones of stress increase/decrease surrounding the fault to have comparable lengths. We also couple short-term dynamic rupture simulation with long-term tectonic modelling. We do this by giving the stress output from one of the dynamic rupture simulation (of a single realization of fault roughness) to long term tectonic model (LTM) as initial condition and then run LTM over duration of seismic cycle. This short term and long term coupling enables us to understand how heterogeneous stresses due to fault geometry influence the dynamics of strain accumulation in the post-seismic and inter-seismic phase of seismic cycle.

Application of super-virtual seismic refraction interferometry to enhance first arrivals: A case study from Saudi Arabia

KAUST Repository

Alshuhail, Abdulrahman Abdullatif Abdulrahman

2012-01-01

Complex near-surface anomalies are one of the main onshore challenges facing seismic data processors. Refraction tomography is becoming a common technology to estimate an accurate near-surface velocity model. This process involves picking the first arrivals of refracted waves. One of the main challenges with refraction tomography is the low signal-to-noise ratio characterizing the first-break waveform arrivals, especially for the far-offset receivers. This is especially evident in data recorded using reflection acquisition geometry. This low signal-to-noise ratio is caused by signal attenuation due to geometrical spreading of the seismic wavefield, near-surface-generated noise, and amplitude absorption. Super-virtual refraction interferometry improves the quality of the first-break picks by enhancing the amplitude of the refracted waves and attenuating the amplitude of the random noise.

Seismic risk assessment in the Mexican Nuclear Center applying the Gumbel-I distribution

International Nuclear Information System (INIS)

Flores R, J.H.; Arguelles F, R.; Camacho L, M.E.; Urrutia F, J.

1997-01-01

A licensing requirement for the operation of nuclear facilities is the performance of different kinds of studies, one of which is seismic risk assessment. This study is useful for the validation of the seismic coefficient applied in the structural design of the facilities. Thus, for the construction of a pilot nuclear fuel plant at Mexico Nuclear Centre of the Instituto Nacional de Investigaciones Nucleares (ININ), was necessary to make such study. The seismicity data for the period between 1912 and 1990 were used and the extreme values Gumbel-I distribution was applied to them. With this, ground acceleration seismic risk maps for recurrence periods of 1, 25 and 50 years were drawn up, showing maximum values of 1.2, 4.25, and 5.0 gales, respectively. (Author)

Channel estimation in DFT-based offset-QAM OFDM systems.

Science.gov (United States)

Zhao, Jian

2014-10-20

Offset quadrature amplitude modulation (offset-QAM) orthogonal frequency division multiplexing (OFDM) exhibits enhanced net data rates compared to conventional OFDM, and reduced complexity compared to Nyquist FDM (N-FDM). However, channel estimation in discrete-Fourier-transform (DFT) based offset-QAM OFDM is different from that in conventional OFDM and requires particular study. In this paper, we derive a closed-form expression for the demultiplexed signal in DFT-based offset-QAM systems and show that although the residual crosstalk is orthogonal to the decoded signal, its existence degrades the channel estimation performance when the conventional least-square method is applied. We propose and investigate four channel estimation algorithms for offset-QAM OFDM that vary in terms of performance, complexity, and tolerance to system parameters. It is theoretically and experimentally shown that simple channel estimation can be realized in offset-QAM OFDM with the achieved performance close to the theoretical limit. This, together with the existing advantages over conventional OFDM and N-FDM, makes this technology very promising for optical communication systems.

Sample Adaptive Offset Optimization in HEVC

Directory of Open Access Journals (Sweden)

Yang Zhang

2014-11-01

Full Text Available As the next generation of video coding standard, High Efficiency Video Coding (HEVC adopted many useful tools to improve coding efficiency. Sample Adaptive Offset (SAO, is a technique to reduce sample distortion by providing offsets to pixels in in-loop filter. In SAO, pixels in LCU are classified into several categories, then categories and offsets are given based on Rate-Distortion Optimization (RDO of reconstructed pixels in a Largest Coding Unit (LCU. Pixels in a LCU are operated by the same SAO process, however, transform and inverse transform makes the distortion of pixels in Transform Unit (TU edge larger than the distortion inside TU even after deblocking filtering (DF and SAO. And the categories of SAO can also be refined, since it is not proper for many cases. This paper proposed a TU edge offset mode and a category refinement for SAO in HEVC. Experimental results shows that those two kinds of optimization gets -0.13 and -0.2 gain respectively compared with the SAO in HEVC. The proposed algorithm which using the two kinds of optimization gets -0.23 gain on BD-rate compared with the SAO in HEVC which is a 47 % increase with nearly no increase on coding time.

Spots of Seismic Danger Extracted by Properties of Low-Frequency Seismic Noise

Science.gov (United States)

Lyubushin, Alexey

2013-04-01

A new method of seismic danger estimate is presented which is based on using properties of low-frequency seismic noise from broadband networks. Two statistics of noise waveforms are considered: multi-fractal singularity spectrum support width D and minimum normalized entropy En of squared orthogonal wavelet coefficients. The maps of D and En are plotted in the moving time window. Let us call the regions extracted by low values of D and high values of En as "spots of seismic danger" - SSD. Mean values of D and En are strongly anti-correlated - that is why statistics D and En extract the same SSD. Nevertheless their mutual considering is expedient because these parameters are based on different approaches. The physical mechanism which underlies the method is consolidation of small blocks of the Earth's crust into the large one before the strong earthquake. This effect has a consequence that seismic noise does not include spikes which are connected with mutual movements of small blocks. The absence of irregular spikes in the noise follows the decreasing of D and increasing of entropy En. The stability in space and size of the SSD provides estimates of the place and energy of the probable future earthquake. The increasing or decreasing of SSD size and minimum or maximum values of D and En within SSD allows estimate the trend of seismic danger. The method is illustrating by the analysis of seismic noise from broadband seismic network F-net in Japan [1-5]. Statistically significant decreasing of D allowed a hypothesis about approaching Japan to a future seismic catastrophe to be formulated at the middle of 2008. The peculiarities of correlation coefficient estimate within 1 year time window between median values of D and generalized Hurst exponent allowed to make a decision that starting from July of 2010 Japan come to the state of waiting strong earthquake [3]. The method extracted a huge SSD near Japan which includes the region of future Tohoku mega-earthquake and the

Seismic testing

International Nuclear Information System (INIS)

Sollogoub, Pierre

2001-01-01

This lecture deals with: qualification methods for seismic testing; objectives of seismic testing; seismic testing standards including examples; main content of standard; testing means; and some important elements of seismic testing

Seismic hazards: New trends in analysis using geologic data

International Nuclear Information System (INIS)

Schwartz, D.P.; Coppersmith, K.J.

1986-01-01

In the late 1960s and early 1970s, largely in response to expansion of nuclear power plant siting and issuance of a code of federal regullations by the Nuclear Regulatory Commission referred to as Appendix A-10CFR100, the need to characterize the earthquake potential of individual faults for seismic design took on greater importance. Appendix A established deterministic procedures for assessing the seismic hazard at nuclear power plant sites. Bonilla and Buchanan, using data from historical suface-faulting earthquakes, developed a set of statistical correlations relating earthquake magnitude to surface rupture length and to surface displacement. These relationships have been refined and updated along with the relationship between fault area and magnitude and seismic moment and moment magnitude have served as the basis for selecting maximum earthquakes in a wide variety of design situations. In the paper presented, the authors discuss new trends in seismic hazard analysis using geologic data, with special emphasis on fault-zone segmentation and recurrence models and the way in which they provide a basis for evaluating long-term earthquake potential

Could the IMS Infrasound Stations Support a Global Network of Small Aperture Seismic Arrays?

OpenAIRE

Kværna, Tormod; Gibbons, Steven; Mykkeltveit, Svein

2017-01-01

The IMS infrasound arrays have up to 15 sites with apertures up to 3 km. They are distributed remarkably uniformly over the globe, providing excellent coverage of South America, Africa, and Antarctica. Therefore, many infrasound arrays are in regions thousands of kilometers from the closest seismic array. Existing 3-component seismic stations, co-located with infrasound arrays, show how typical seismic signals look at these locations. We estimate a theoretical array response assuming a seismo...

Design and analysis of fractional order seismic transducer for displacement and acceleration measurements

Science.gov (United States)

Veeraian, Parthasarathi; Gandhi, Uma; Mangalanathan, Umapathy

2018-04-01

Seismic transducers are widely used for measurement of displacement, velocity, and acceleration. This paper presents the design of seismic transducer in the fractional domain for the measurement of displacement and acceleration. The fractional order transfer function for seismic displacement and acceleration transducer are derived using Grünwald-Letnikov derivative. Frequency response analysis of fractional order seismic displacement transducer (FOSDT) and fractional order seismic acceleration transducer (FOSAT) are carried out for different damping ratio with the different fractional order, and the maximum dynamic measurement range is identified. The results demonstrate that fractional order seismic transducer has increased dynamic measurement range and less phase distortion as compared to the conventional seismic transducer even with a lower damping ratio. Time response of FOSDT and FOSAT are derived analytically in terms of Mittag-Leffler function, the effect of fractional behavior in the time domain is evaluated from the impulse and step response. The fractional order system is found to have significantly reduced overshoot as compared to the conventional transducer. The fractional order seismic transducer design proposed in this paper is illustrated with a design example for FOSDT and FOSAT. Finally, an electrical equivalent of FOSDT and FOSAT is considered, and its frequency response is found to be in close agreement with the proposed fractional order seismic transducer.

Seismic simulation and functional performance evaluation of a safety related, seismic category I control room emergency air cleaning system

International Nuclear Information System (INIS)

Manley, D.K.; Porco, R.D.; Choi, S.H.

1985-01-01

Under a nuclear contract MSA was required to design, manufacture, seismically test and functionally test a complete Safety Related, Seismic Category I, Control Room Emergency Air Cleaning System before shipment to the Yankee Atomic Electric Company, Yankee Nuclear Station in Rowe, Massachusetts. The installation of this system was required to satisfy the NRC requirements of NUREG-0737, Section III, D.3.4, ''Control Room Habitability''. The filter system tested was approximately 3 ft. wide by 8 ft. high by 18 ft. long and weighed an estimated 8300 pounds. It had a design flow rate of 3000 SCFM and contained four stages of filtration - prefilters, upstream and downstream HEPA filters and Type II sideload charcoal adsorber cells. The filter train design followed the guidelines set forth by ANSI/ASME N509-1980. Seismic Category I Qualification Testing consisted of resonance search testing and triaxial random multifrequency testing. In addition to ANSI/ASME N510-1980 testing, triaxial response accelerometers were placed at specific locations on designated prefilters, HEPA filters, charcoal adsorbers and test canisters along with accelerometers at the corresponding filter seal face locations. The purpose of this test was to demonstrate the integrity of the filters, filter seals, and monitor seismic response levels which is directly related to the system's ability to function during a seismic occurrence. The Control Room Emergency Air Cleaning System demonstrated the ability to withstand the maximum postulated earthquake for the plant site by remaining structurally sound and functional

Relationship between acoustic voice onset and offset and selected instances of oscillatory onset and offset in young healthy males and females

Science.gov (United States)

Patel, Rita; Forrest, Karen; Hedges, Drew

2016-01-01

Objective To investigate the relationship between (1) onset of the acoustic signal and pre-phonatory phases associated with oscillatory onset and (2) offset of the acoustic signal with the post-phonatory events associated with oscillatory offset across vocally healthy adults. Subjects and Methods High-speed videoendoscopy was captured simultaneously with the acoustic signal during repeated production of /hi.hi.hi/ at typical pitch and loudness from 56 vocally healthy adults (age 20–42 years; 21 male, 35 female). The relationship between the acoustic sound pressure signal and oscillatory onset /offset events from the glottal area waveforms (GAW), were statistically investigated using a multivariate linear regression analysis. Results The onset of the acoustic signal (X1a) is a significant predictor of the onset of first oscillations (X1g) and onset of sustained oscillations (X2g). X1a as well as gender are significant predictors of the first instance of medial contact (X1.5g). The offset of the acoustic signal (X2a) is a significant predictor of the first instance of oscillatory offset (X3g), first instance of incomplete glottal closure (X3.5g), and cessation of vocal fold motion (X4g). Conclusions The acoustic signal onset is closely related to the first medial contact of the vocal folds but the latency between these events is longer for females compared to males. The offset of the acoustic signal occurs immediately after incomplete glottal adduction. The emerging normative group latencies between the onset/offset of the acoustic and the GAW from this study appear promising for future investigations. PMID:27769696

Research on Stress Neutral Layer Offset in the Straightening Process

Directory of Open Access Journals (Sweden)

Hailian Gui

2015-01-01

Full Text Available The stress neutral layer offset is analyzed by theoretical and numerical calculation methods. In traditional straightening theory, the stress neutral layer was consistent with the geometric central layer. However, there is a phenomenon that the stress neutral layer has some offset with the geometric neutral layer. This offset is a very important factor for improving the precision of the straightening force. The formula of the stress neutral layer offset is obtained by a theoretical method and the change law is given by numerical calculation method. The neutral layer offset theory provides the theoretical basis for establishing the model of straightening force precisely.

Effects of fault heterogeneity on seismic energy and spectrum

Science.gov (United States)

Dragoni, Michele; Santini, Stefano

2017-12-01

We study the effects of friction heterogeneity on the dynamics of a seismogenic fault. To this aim, we consider a fault model containing two asperities with different static frictions and a rate-dependent dynamic friction. We consider the seismic events produced by the consecutive failure of the two asperities and study their properties as functions of the ratio between static frictions. In particular, we calculate the moment rate, the stress evolution during fault slip, the average stress drop, the partitioning of energy release, the seismic energy, the far-field waveforms and the spectrum of seismic waves. These quantities depend to various extent on the friction distribution on the fault. In particular, the stress distribution on the fault is always strongly heterogeneous at the beginning of the seismic event. Seismic energy and frictional heat decrease with increasing friction heterogeneity, while seismic efficiency is constant. We obtain an equation relating seismic efficiency to the parameters of the friction law, showing that the efficiency is maximum for smaller values of dynamic friction. The seismic spectrum depends on the friction distribution as to the positions and the values of the minima. However, under the model assumption that the slip durations are the same for both asperities, the corner frequency is independent of the friction distribution, but it depends on the friction law and on the coupling between asperities. The model provides a relation between the total radiated energy and the seismic moment that is consistent with the empirical relation between the two quantities. The fault model with one asperity is also considered as a particular case. The model is applied to the 1965 Rat Islands (Alaska) earthquake and shows the role of fault heterogeneity in controlling the spatial distribution of stress drop as well as the time dependence and the final amount of radiated energy.

Seismic considerations in sealing a potential high-level radioactive waste repository

International Nuclear Information System (INIS)

Fernandez, J.A.; Richardson, A.M.; Lin, Ming

1992-01-01

The potential repository system is intended to isolate high-level radioactive waste at Yucca Mountain. One subsystem that may contribute to achieving this objective is the sealing subsystem. This subsystem is comprised of sealing components in the shafts, ramps, underground network of drifts, and the exploratory boreholes. Sealing components can be rigid, as in the case of a shaft seal, or can be more compressible, as in the case of drift fill comprised of mined rockfill. This paper presents the preliminary seismic response of discrete sealing components in welded and nonwelded tuff. Special consideration is given to evaluating the stress in the seal, and the behavior of the interface between the seal and the rock. The seismic responses are computed using both static and dynamic analyses. Also presented is an evaluation of the maximum seismic response encountered by a drift seal with respect to the angle of incidence of the seismic wave. Mitigation strategies and seismic design considerations are proposed which can potentially enhance the overall response of the sealing component and subsequently, the performance of the overall repository system

seismic-py: Reading seismic data with Python

Directory of Open Access Journals (Sweden)

2008-08-01

Full Text Available The field of seismic exploration of the Earth has changed
dramatically over the last half a century. The Society of Exploration
Geophysicists (SEG has worked to create standards to store the vast
amounts of seismic data in a way that will be portable across computer
architectures. However, it has been impossible to predict the needs of the
immense range of seismic data acquisition systems. As a result, vendors have
had to bend the rules to accommodate the needs of new instruments and
experiment types. For low level access to seismic data, there is need for a
standard open source library to allow access to a wide range of vendor data
files that can handle all of the variations. A new seismic software package,
seismic-py, provides an infrastructure for creating and managing drivers for
each particular format. Drivers can be derived from one of the known formats
and altered to handle any slight variations. Alternatively drivers can be
developed from scratch for formats that are very different from any previously
defined format. Python has been the key to making driver development easy
and efficient to implement. The goal of seismic-py is to be the base system
that will power a wide range of experimentation with seismic data and at the
same time provide clear documentation for the historical record of seismic
data formats.

Seismic tests on models of reinforced-concrete Category I buildings

International Nuclear Information System (INIS)

Dove, R.C.; Endebrock, E.G.; Dunwoody, W.E.; Bennett, J.G.

1985-01-01

The behavior of reinforced concrete (R/C), Category I noncontainment nuclear power plant structures subjected to seismic events of magnitude greater than used in their original design has been investigated using two sizes of scale models. Test results were analyzed to determine (1) maximum input for the response to remain linear/elastic; (2) changes in stiffness, damping, and modal frequency that are produced by seismic input greater than that causing linear elastic response; (3) changes in floor response spectra when the structure's response is nonlinear/inelastic; and (4) the magnitude of the seismic event necessary to fail (excessively crack) these structures. By constructing models of two sizes, it was possible to make two independent predictions of prototype behavior and to compare the results from the two models. 1 ref., 4 figs., 1 tab

Influence of the crustal and subcrustal Vrancea seismic sources on Cernavoda nuclear power plant site

International Nuclear Information System (INIS)

Marmureanu, Gheorghe; Popescu, Emilia; Mircea Radulian

2002-01-01

The basis of the seismic hazard assessment in different geographical regions with dense-populated areas and strategic objectives (dams, nuclear power plants, etc.) is the study of seismicity of the seismogenic sources which affect these sites. The purpose of this paper is to provide a complete set of information relative to the Vrancea seismic source (in the crust and the intermediate depth domains) that is fundamental for the seismic hazard evaluation at Cernavoda nuclear power plant site. The analysis that we propose has to deal with the following items: (1) geometrical definition of the seismic sources; (2) setting the earthquake catalog associated to each seismic source; (3) estimation of the maximum possible magnitude; (4) estimation of the frequency - magnitude relationship; (5) computation of the distribution function for focal distance; (6) correlation between focal depth and magnitude; (7) attenuation law. We discuss also the implications of the model parameters on the seismic hazard level. (authors)

The utility of petroleum seismic exploration data in delineating structural features within salt anticlines

Science.gov (United States)

Stockton, S.L.; Balch, Alfred H.

1978-01-01

mapping the thin beds because of the lack of sufficient resolution to provide direct evidence of the presence of the thin beds. However, indirect evidence, present in these data as discontinuous seismic events, suggests that two geophysical techniques designed for this specific problem would allow direct detection of the interbeds in salt. These techniques are vertical seismic profiling and shallow, short-offset, high-frequency, seismic-reflection recording.

Seismic texture and amplitude analysis of large scale fluid escape pipes using time lapses seismic surveys: examples from the Loyal Field (Scotland, UK)

Science.gov (United States)

Maestrelli, Daniele; Jihad, Ali; Iacopini, David; Bond, Clare

2016-04-01

Fluid escape pipes are key features of primary interest for the analysis of vertical fluid flow and secondary hydrocarbon migration in sedimentary basin. Identified worldwide (Løset et al., 2009), they acquired more and more importance as they represent critical pathways for supply of methane and potential structure for leakage into the storage reservoir (Cartwright & Santamarina, 2015). Therefore, understanding their genesis, internal characteristics and seismic expression, is of great significance for the exploration industry. Here we propose a detailed characterization of the internal seismic texture of some seal bypass system (e.g fluid escape pipes) from a 4D seismic survey (released by the BP) recently acquired in the Loyal Field. The seal by pass structure are characterized by big-scale fluid escape pipes affecting the Upper Paleogene/Neogene stratigraphic succession in the Loyal Field, Scotland (UK). The Loyal field, is located on the edge of the Faroe-Shetland Channel slope, about 130 km west of Shetland (Quadrants 204/205 of the UKCS) and has been recently re-appraised and re developed by a consortium led by BP. The 3D detailed mapping analysis of the full and partial stack survey (processed using amplitude preservation workflows) shows a complex system of fluid pipe structure rooted in the pre Lista formation and developed across the paleogene and Neogene Units. Geometrical analysis show that pipes got diameter varying between 100-300 m and a length of 500 m to 2 km. Most pipes seem to terminate abruptly at discrete subsurface horizons or in diffuse termination suggesting multiple overpressured events and lateral fluid migration (through Darcy flows) across the overburden units. The internal texture analysis of the large pipes, (across both the root and main conduit zones), using near, medium and far offset stack dataset (processed through an amplitude preserved PSTM workflow) shows a tendency of up-bending of reflection (rather than pulls up artefacts

Seismotectonic significance of the 2008–2010 Walloon Brabant seismic swarm in the Brabant Massif, Belgium

Science.gov (United States)

Van Noten, Koen; Lecocq, Thomas; Shah, Anjana K.; Camelbeeck, Thierry

2015-01-01

Between 12 July 2008 and 18 January 2010 a seismic swarm occurred close to the town of Court-Saint-Etienne, 20 km SE of Brussels (Belgium). The Belgian network and a temporary seismic network covering the epicentral area established a seismic catalogue in which magnitude varies between ML -0.7 and ML 3.2. Based on waveform cross-correlation of co-located earthquakes, the spatial distribution of the hypocentre locations was improved considerably and shows a dense cluster displaying a 200 m-wide, 1.5-km long, NW-SE oriented fault structure at a depth range between 5 and 7 km, located in the Cambrian basement rocks of the Lower Palaeozoic Anglo-Brabant Massif. Waveform comparison of the largest events of the 2008–2010 swarm with an ML 4.0 event that occurred during swarm activity between 1953 and 1957 in the same region shows similar P- and S-wave arrivals at the Belgian Uccle seismic station. The geometry depicted by the hypocentral distribution is consistent with a nearly vertical, left-lateral strike-slip fault taking place in a current local WNW–ESE oriented local maximum horizontal stress field. To determine a relevant tectonic structure, a systematic matched filtering approach of aeromagnetic data, which can approximately locate isolated anomalies associated with hypocentral depths, has been applied. Matched filtering shows that the 2008–2010 seismic swarm occurred along a limited-sized fault which is situated in slaty, low-magnetic rocks of the Mousty Formation. The fault is bordered at both ends with obliquely oriented magnetic gradients. Whereas the NW end of the fault is structurally controlled, its SE end is controlled by a magnetic gradient representing an early-orogenic detachment fault separating the low-magnetic slaty Mousty Formation from the high-magnetic Tubize Formation. The seismic swarm is therefore interpreted as a sinistral reactivation of an inherited NW–SE oriented isolated fault in a weakened crust within the Cambrian core of

Localization of short-range acoustic and seismic wideband sources: Algorithms and experiments

Science.gov (United States)

Stafsudd, J. Z.; Asgari, S.; Hudson, R.; Yao, K.; Taciroglu, E.

2008-04-01

We consider the determination of the location (source localization) of a disturbance source which emits acoustic and/or seismic signals. We devise an enhanced approximate maximum-likelihood (AML) algorithm to process data collected at acoustic sensors (microphones) belonging to an array of, non-collocated but otherwise identical, sensors. The approximate maximum-likelihood algorithm exploits the time-delay-of-arrival of acoustic signals at different sensors, and yields the source location. For processing the seismic signals, we investigate two distinct algorithms, both of which process data collected at a single measurement station comprising a triaxial accelerometer, to determine direction-of-arrival. The direction-of-arrivals determined at each sensor station are then combined using a weighted least-squares approach for source localization. The first of the direction-of-arrival estimation algorithms is based on the spectral decomposition of the covariance matrix, while the second is based on surface wave analysis. Both of the seismic source localization algorithms have their roots in seismology; and covariance matrix analysis had been successfully employed in applications where the source and the sensors (array) are typically separated by planetary distances (i.e., hundreds to thousands of kilometers). Here, we focus on very-short distances (e.g., less than one hundred meters) instead, with an outlook to applications in multi-modal surveillance, including target detection, tracking, and zone intrusion. We demonstrate the utility of the aforementioned algorithms through a series of open-field tests wherein we successfully localize wideband acoustic and/or seismic sources. We also investigate a basic strategy for fusion of results yielded by acoustic and seismic arrays.

Probable Maximum Earthquake Magnitudes for the Cascadia Subduction

Science.gov (United States)

Rong, Y.; Jackson, D. D.; Magistrale, H.; Goldfinger, C.

2013-12-01

The concept of maximum earthquake magnitude (mx) is widely used in seismic hazard and risk analysis. However, absolute mx lacks a precise definition and cannot be determined from a finite earthquake history. The surprising magnitudes of the 2004 Sumatra and the 2011 Tohoku earthquakes showed that most methods for estimating mx underestimate the true maximum if it exists. Thus, we introduced the alternate concept of mp(T), probable maximum magnitude within a time interval T. The mp(T) can be solved using theoretical magnitude-frequency distributions such as Tapered Gutenberg-Richter (TGR) distribution. The two TGR parameters, β-value (which equals 2/3 b-value in the GR distribution) and corner magnitude (mc), can be obtained by applying maximum likelihood method to earthquake catalogs with additional constraint from tectonic moment rate. Here, we integrate the paleoseismic data in the Cascadia subduction zone to estimate mp. The Cascadia subduction zone has been seismically quiescent since at least 1900. Fortunately, turbidite studies have unearthed a 10,000 year record of great earthquakes along the subduction zone. We thoroughly investigate the earthquake magnitude-frequency distribution of the region by combining instrumental and paleoseismic data, and using the tectonic moment rate information. To use the paleoseismic data, we first estimate event magnitudes, which we achieve by using the time interval between events, rupture extent of the events, and turbidite thickness. We estimate three sets of TGR parameters: for the first two sets, we consider a geographically large Cascadia region that includes the subduction zone, and the Explorer, Juan de Fuca, and Gorda plates; for the third set, we consider a narrow geographic region straddling the subduction zone. In the first set, the β-value is derived using the GCMT catalog. In the second and third sets, the β-value is derived using both the GCMT and paleoseismic data. Next, we calculate the corresponding mc

Formation of Offset and Dual Active Galactic Nuclei

Science.gov (United States)

Barrows, Scott; Comerford, Julia M.; Greene, Jenny E.

2018-06-01

Galaxy mergers are effective mechanisms for triggering accretion onto supermassive black holes (SMBHs) and thereby powering active galactic nuclei (AGN). In the merger scenario, when the SMBH from only one galaxy is accreting we observe a spatially offset AGN, and when the SMBHs from both galaxies are accreting we observe a dual AGN. Understanding the merger conditions that lead to the formation of offset AGN versus dual AGN is fundamental to informing models of hierarchical SMBH growth and the physics leading to the accretion of matter onto SMBHs. However, while the role of galaxy mergers for AGN triggering has been well-studied, the efficiency with which these events trigger offset AGN versus dual AGN is currently unclear. One reason for this gap in knowledge can be attributed to the observational difficulties in distinguishing between offset and dual AGN since doing so requires high spatial resolution, especially in the small separation regime where merger-driven AGN triggering is most likely to occur. To overcome this hurdle, we have utilized the spatial resolution of the Chandra X-ray Observatory to develop a unique sample of AGN hosted by late-stage galaxy mergers. Moreover, we have recently acquired Hubble Space Telescope imaging for a subset of these systems to examine the role that their merger morphologies play in SMBH growth and the formation of offset and dual AGN. We find that offset AGN are predominately found in minor mergers, whereas dual AGN are usually hosted by major mergers and galaxies with large morphological asymmetries. Furthermore, in both offset and dual AGN, the rate of SMBH growth increases toward more major mergers and larger morphological asymmetries. These results are in agreement with numerical simulations predicting that merger morphology is a relevant parameter governing SMBH merger-driven growth, and these results are the first to observationally confirm these trends at small pair separations.

Carbon offsets, reversal risk and US climate policy

Directory of Open Access Journals (Sweden)

Chen Yihsu

2009-06-01

Full Text Available Abstract Background One controversial issue in the larger cap-and-trade debate is the proper use and certification of carbon offsets related to changes in land management. Advocates of an expanded offset supply claim that inclusion of such activities would expand the scope of the program and lower overall compliance costs, while opponents claim that it would weaken the environmental integrity of the program by crediting activities that yield either nonexistent or merely temporary carbon sequestration benefits. Our study starts from the premise that offsets are neither perfect mitigation instruments nor useless "hot air." Results We show that offsets provide a useful cost containment function, even when there is some threat of reversal, by injecting additional "when-flexibility" into the system. This allows market participants to shift their reduction requirements to periods of lower cost, thereby facilitating attainment of the least-cost time path without jeopardizing the cumulative environmental integrity of the system. By accounting for market conditions in conjunction with reversal risk, we develop a simple offset valuation methodology, taking into account the two most important factors that typically lead offsets to be overvalued or undervalued. Conclusion The result of this paper is a quantitative "model rule" that could be included in future legislation or used as a basis for active management by a future "carbon fed" or other regulatory authority with jurisdiction over the US carbon market to actively manage allowance prices.

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 4A. Paks NPP: Analysis/testing. Working material

International Nuclear Information System (INIS)

1995-01-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports on data related to seismic analyses of structures of Paks and Kozloduy reactor buildings and WWER-440/213 primary coolant loops with different antiseismic devices

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 4A. Paks NPP: Analysis/testing. Working material

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports on data related to seismic analyses of structures of Paks and Kozloduy reactor buildings and WWER-440/213 primary coolant loops with different antiseismic devices.

Data analysis for seismic motion characteristics

International Nuclear Information System (INIS)

Ishimaru, Tsuneari; Kohriya, Yorihide

2002-10-01

This data analysis is aimed at studying the characteristics of amplification of acceleration amplitude from deep underground to the surface, and is one of several continuous studies on the effects of earthquake motion. Seismic wave records were observed via a center array located in Shibata-cho, Miyagi Prefecture, which is part of the Kumagai-Gumi Array System for Strong Earthquake Motion (KASSEM) located on the Pacific coast in Miyagi and Fukushima Prefectures. Using acceleration waves obtained from earthquake observations, the amplification ratios of maximum acceleration amplitude and of root mean square acceleration amplitude which were based on the deepest observation point were estimated. Comparison between the seismic motion amplification characteristics of this study were made with the analyzed data at the Kamaishi-Mine (Kamaishi Miyagi Prefecture). The obtained results are as follows. The amplification ratios estimated from maximum acceleration amplitude and root mean square acceleration amplitude are almost constant in soft rock formations. However, amplification ratios at the surface in diluvium and alluvium are about three to four times larger than the ratios in soft rock formations. The amplification ratios estimated from root mean square acceleration amplitude are less dispersed than the ratios estimated from maximum acceleration amplitude. Comparing the results of this analysis with the results obtained at the Kamaishi-Mine, despite the difference in the rock types and the geologic formations at the observation points, there is a tendency for the amplification ratios at both points to be relatively small in the rock foundation and gradually increase toward the ground surface. (author)

Offset Implementations for Turkey’s International Defense Acquisitions

Science.gov (United States)

2008-12-01

has been a source of confusion in the field of offsets and countertrade (Schmidt, 1989, p. 4) Compensatory trade agreements — or reciprocal trade...complementary policy instruments. Countertrade and offset terms have usually been overall terms to define and classify reciprocal trade agreements...motives and characteristics in nature. Author Grant T. Hammond classifies reciprocal trade as countertrade , offsets and barter — which involve all

The influence of the mining operation on the mine seismicity of Vorkuta coal deposit

Science.gov (United States)

Zmushko, T.; Turuntaev, S. B.; Kulikov, V. I.

2012-04-01

The mine seismicity of Vorkuta coal deposit was analyzed. Seismic network consisting of 24 seismic sensors (accelerometers) cover the area of "Komsomolskaya" and "North" mines of Vorkuta deposit. Also there is seismic station of IDG RAS with three-component seismometer near this mines for better defining energy of the seismic events. The catalogs of seismic events contain 9000 and 7000 events with maximum magnitude M=2.3 for "Komsomolskaya" and "North" mines respectively and include the period from 01.09.2008 to 01.09.2011. The b-value of the magnitude-frequency relation was -1.0 and -1.15 respectively for the mines, meanwhile b-value for the nature seismicity was -0,9. It was found, that the number of seismic events per hour during mine combine operation is higher in 2.5 times than the number of seismic events during the break in the operation. Also, the total energy of the events per hour during the operation is higher in 3-5 times than during the break. The study showed, that the number and the energy of the seismic events relate with the hours of mine combine operation. The spatial distribution of the seismic events showed, that 80% of all events and 85% of strong events (M>1.6) were located in and near the longwall under development during the mine combine operations as well asduring the breaks. The isoclines of seismic event numbers proved that the direction of motion of the boundary of seismic events extension coincides with the direction of development, the maximum number of events for any period lies within the wall under operation. The rockburst with M=2.3 occurring at the North mine at July 16, 2011 was considered. The dependences of the energy and of the number of events with different magnitudes on the time showed that the number of events with M=1 and especially M=0.5 before the rockburst decreased, which corresponds to the prognostic seismic quietness, described in the research works. The spatial distribution of the events for the 6 month before the

PARAMETERS OF KAMCHATKA SEISMICITY IN 2008

Directory of Open Access Journals (Sweden)

Vadim A. Saltykov

2010-01-01

estimations give evidence that the year of 2008 was not anomalous in terms of seismicity. Based on 2D distribution of recurrence graph slope γ, it is possible to locate an area of lower values of γ in the southern part of the Kamchatka seismic zone (Fig. 4. Data on maps of normalized variation of γ for 2007–2008 and 2006–2008 (Fig. 5 confirm statistical importance of γ reduction through the last three years in the given area. Maps of 2D distribution of seismic activity A10 are constructed for 2008 and the perdiod from 1962 to 2008; values of seismic activity A10 that are normalized to the average annual seismic activity are also mapped (Fig. 6. In 2008, increased values of A10 were observed at the southern part of the Avachinsky gulf and at the northern part of the Kamchatka gulf, as well as in the northern water area of Bering Island. The anomalous behavior of parameters RTL, ΔS and clustering of earthquakes may have predictive character [Sobolev, 2000]. Negative values of RTL-parameter correspond to seismic quiescence; increasing areas of seismic ruptures ΔS correspond to foreshock activation; clustering of earthquakes can evidence that activation tends to accumulate at a future main rupture location. For 2008, three zones of seismic quiescence were defined by data (Fig. 7. For estimation points with maximum modular values of RTL (marked by the Roman numerals in Fig. 7, RTL time curves are constructed for each of the above mentioned zones (Fig. 8; they provide for defining durations of anomalies and degrees of manifestation. A map of variations of seismic rupture areas ΔS (Fig. 9 shows that seismic activity of 2008 was mainly manifested at the southern part of the Kamchatka seismic zone. In 2008, most of the earthquake clusters varying in energy also occurred in the southern part of Kamchatka (Fig. 10. The northern chain of clusters is located at the border of the developing seismic anomaly, as defined by RTL parameter. Similar to RTL technique, an objective of

Combined effects of traveling seismic waves and soil nonlinearity on nuclear power plant response

International Nuclear Information System (INIS)

Lee, T.H.; Charman, C.M.

1981-01-01

The effects of ground motion nonuniformity on the seismic input have been actively studied in recent years by considering the passage of traveling seismic waves. These studies gave rise to a new class of soil-structure interaction problems in which the seismic input is modified as a result of the spatial variations of ground motion. The phenomena were usually studied by using the elastic half-space simulation or discrete spring-models for modeling the soil medium. Finite element methods were also used recently on a limited scope. Results obtained from these investigations are often manifested by an attenuation of translational excitation along with an addition of rotational ground motion input. The decrease in structural response resulting from the input loss in the translational component was often insignificant since the response reduction tends to be offset by the effects from rotational input. The traveling wave effects have, so far, been investigated within the framework of linear theory with soil nonlinearity ignored. Conversely, the incorporation of soil nonlinearity in soil-structure interaction analyses has been done without including wave effect. Seismic analyses considering the hysteretic behavior of soil have been performed using highly idealized models for steady-state solution. More elaborate nonlinear seismic models deal with only the strain-dependent soil modulus rather than the transient unloading-reloading type of hysteretic characteristics of soil under a time-function input of earthquake trace. Apparently, the traveling wave effect and soil nonlinearity have been separately treated in the past. The purpose of this paper is to demonstrate that these two major effects can be combined in one model such that the influence of wave passage is reflected through the hysteretic behavior of soil particles, and thereby achieving significant reduction in seismic loads. (orig./RW)

Etude Climat no. 31 'Carbon offset projects in the agricultural sector'

International Nuclear Information System (INIS)

Foucherot, Claudine; Bellassen, Valentin

2012-01-01

Among the publications of CDC Climat Research, 'Climate Reports' offer in-depth analyses on a given subject. This issue addresses the following points: The agricultural sector accounts for 14% of global anthropogenic greenhouse gas emissions. If we also take into account carbon emissions and sequestration from upstream - production of fertilisers, deforestation, etc. - and downstream - bio-energies, etc. - the share rises to 30%. Many practices and technologies enable agriculture's impact on climate change to be reduced. According to a number of estimates that are summarised in this research, the agricultural sector's mitigation potential is of the same order of magnitude as its emissions over a period of 30 years. However, changing agricultural practices comes at a cost, and in most cases such changes are not made without economic incentives. Carbon offsetting projects are one of the economic tools available to reduce agricultural emissions by paying for metric tons of avoided CO 2 e emissions. A summary of the emission reductions enabled by agricultural projects to date is provided in this report. It covers most projects certified by quality assurance standards, including those set up by the Kyoto Protocol (Clean Development Mechanism and Joint Implementation) and those in the voluntary market (Verified Carbon Standard, Climate Action Reserve, Gold Standard, Chicago Climate Exchange, and American Carbon Registry). The assessment drawn up on this basis shows that emission reductions enabled through carbon offsetting are thousand times lower than actual emissions and their potential mitigation. Agricultural projects have reduced emissions by 14 MtCO 2 e in 2010, i.e. 7% of the reductions generated by all carbon offset projects across all sectors for this year. Initiatives focus on three technologies: - bio-energies (crop residues), - methanation of livestock waste, - and soil carbon sequestration using no-till practices. This is very little compared with the large

Seismic hazard of the Enriquillog-Plantain Garden fault in Haiti inferred from palaeoseismology

Science.gov (United States)

Prentice, C.S.; Mann, P.; Crone, A.J.; Gold, R.D.; Hudnut, K.W.; Briggs, R.W.; Koehler, R.D.; Jean, P.

2010-01-01

The Enriquillog-Plantain Garden fault zone is recognized as one of the primary plate-bounding fault systems in Haiti. The strike-slip fault runs adjacent to the city of Port-au-Prince and was initially thought to be the source of the 12 January 2010, M w 7.0 earthquake. Haiti experienced significant earthquakes in 1751 and 1770 (refsA, 3, 4, 5), but the role of the Enriquillog-Plantain Garden fault zone in these earthquakes is poorly known. We use satellite imagery, aerial photography, light detection and ranging (LIDAR) and field investigations to document Quaternary activity on the Enriquillog-Plantain Garden fault. We report late Quaternary, left-lateral offsets of up to 160m, and a set of small offsets ranging from 1.3 to 3.3m that we associate with one of the eighteenth century earthquakes. The size of the small offsets implies that the historical earthquake was larger than M w 7.0, but probably smaller than M w 7.6. We found no significant surface rupture associated with the 2010 earthquake. The lack of surface rupture, coupled with other seismologic, geologic and geodetic observations, suggests that little, if any, accumulated strain was released on the Enriquillog-Plantain Garden fault in the 2010 earthquake. These results confirm that the Enriquillog-Plantain Garden fault remains a significant seismic hazard. ?? 2010 Macmillan Publishers Limited. All rights reserved.

36 CFR 1011.10 - How will the Presidio Trust use administrative offset (offset of non-tax federal payments) to...

Science.gov (United States)

2010-07-01

... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false How will the Presidio Trust... Trust Debts § 1011.10 How will the Presidio Trust use administrative offset (offset of non-tax federal...) If not already transferred to the FMS under § 1011.9 of this part, the Presidio Trust will refer any...

Status for seismic design requirements of nuclear power plants in Japan

International Nuclear Information System (INIS)

Takahashi, H.

1977-01-01

The fundamental purpose for the aseismic design of the nuclear power plants is to protect the inhabitants near the plant from radiation accidents during and after earthquake vibrations. In order to achieve the above purpose, the following considerations have been made. All buidlings, structures, system and components are classified into three Classes A, B and C according to their degree of importance for plant safety, and are designed to meet the requirements specified for each class, respectively. Magnitude and epicenter of the design basis earthquake are determined based upon seismological and geological investigations and observation of ground motion in the site, and the maximum ground acceleration which could be expected can be calculated empirically. With respect to time history waves, more than three are selected referring to dynamic characteristic of base rock in the site, observed ground motion records in the site or other strong motion seismographs.The figures of horizontal seismic coefficients to be used in determining design forces on Class A buildings and structures are 3 Co (where Co. is as defined in the Japan Building Standard Law). On the other hand the horizontal design force should not be less than those determined as the results of the dynamic analyses based on DEGM (Design Earthquake Ground Motion). The figures of horizontal seismic coefficient and forces for Class A system and components are usually determined based on the dynamic analyses for DEGM. The buildings and structures treated as an elastic column system with masses, and the bottom mass is supported by elastic springs representing the soil-foundation interaction characteristics. DEGM is used as the input disturbance in the dynamic response analysis, and the model analysis or time history method is worked out. System and components are modeled as elastic bars with lumped masses of 3 dimensional degree of freedom, and the response analysis is carried out using floor respone spectra

Innovations in seismic tomography, their applications and induced seismic events in carbon sequestration

Science.gov (United States)

Li, Peng

This dissertation presents two innovations in seismic tomography and a new discovery of induced seismic events associated with CO2 injection at an Enhanced Oil Recovery (EOR) site. The following are brief introductions of these three works. The first innovated work is adaptive ambient seismic noise tomography (AANT). Traditional ambient noise tomography methods using regular grid nodes are often ill posed because the inversion grids do not always represent the distribution of ray paths. Large grid spacing is usually used to reduce the number of inversion parameters, which may not be able to solve for small-scale velocity structure. We present a new adaptive tomography method with irregular grids that provides a few advantages over the traditional methods. First, irregular grids with different sizes and shapes can fit the ray distribution better and the traditionally ill-posed problem can become more stable owing to the different parameterizations. Second, the data in the area with dense ray sampling will be sufficiently utilized so that the model resolution can be greatly improved. Both synthetic and real data are used to test the newly developed tomography algorithm. In synthetic data tests, we compare the resolution and stability of the traditional and adaptive methods. The results show that adaptive tomography is more stable and performs better in improving the resolution in the area with dense ray sampling. For real data, we extract the ambient noise signals of the seismic data near the Garlock Fault region, obtained from the Southern California Earthquake Data Center. The resulting group velocity of Rayleigh waves is well correlated with the geological structures. High velocity anomalies are shown in the cold southern Sierra Nevada, the Tehachapi Mountains and the Western San Gabriel Mountains. The second innovated work is local earthquake tomography with full topography (LETFT). In this work, we develop a new three-dimensional local earthquake tomography

41 CFR 105-56.027 - Centralized salary offset computer match.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Centralized salary... Services Administration 56-SALARY OFFSET FOR INDEBTEDNESS OF FEDERAL EMPLOYEES TO THE UNITED STATES Centralized Salary Offset (CSO) Procedures-GSA as Paying Agency § 105-56.027 Centralized salary offset...

41 CFR 105-56.017 - Centralized salary offset computer match.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Centralized salary... Services Administration 56-SALARY OFFSET FOR INDEBTEDNESS OF FEDERAL EMPLOYEES TO THE UNITED STATES Centralized Salary Offset (CSO) Procedures-GSA as Creditor Agency § 105-56.017 Centralized salary offset...

Groundwater geochemistry of the Mt. Vesuvius area: implications for volcano surveillance and relationship with hydrological and seismic signals

Directory of Open Access Journals (Sweden)

Cinzia Federico

2013-11-01

Full Text Available Geochemical data obtained between 1998 and 2011 at the Mt. Vesuvius aquifer are discussed, focusing on the effects of both the hydrological regime and the temporal pattern of local seismicity. Water samples were collected in a permanent network of wells and springs located in the areas that are mostly affected by the ascent of magmatic volatiles, and their chemical composition and dissolved gas content were analyzed. As well as the geochemical parameters that describe the behavior of groundwater at Mt. Vesuvius, we discuss the temporal distribution of volcano-tectonic earthquakes. The seismological data set was collected by the stations forming the permanent and mobile network of the Istituto Nazionale di Geofisica e Vulcanologia - Osservatorio Vesuviano (INGV-OV. Our analysis of seismic data collected during 1998-2011 identified statistically significant variations in the seismicity rate, marked by phases of decreasing activity from October 1999 to May 2001 and increasing activity from August 2004 to mid-2006. The water chemistry shows peculiar patterns, characterized by a changeable input of CO2-rich and saline water, which must be related to either a changing stress field or an increased input of CO2-rich vapor. The water chemistry data from 1999 to 2003 account for both higher fluid pressure (which induced the seismic crisis of 1999 that peaked with a 3.6-magnitude earthquake in October 1999 and the increased input of CO2-rich fluids. The highest emission of CO2 from the crater fumaroles and the corresponding increase in dissolved carbon in groundwater characterize the phase of low seismicity. The termination of the phase of intense deep degassing is associated with a change in water chemistry and a peculiar seismic event that was recorded in July 2003. All these seismic and geochemical patterns are interpreted according to temporal variations in the regional and local stress field.

Net present biodiversity value and the design of biodiversity offsets.

Science.gov (United States)

Overton, Jacob McC; Stephens, R T Theo; Ferrier, Simon

2013-02-01

There is an urgent need to develop sound theory and practice for biodiversity offsets to provide a better basis for offset multipliers, to improve accounting for time delays in offset repayments, and to develop a common framework for evaluating in-kind and out-of-kind offsets. Here, we apply concepts and measures from systematic conservation planning and financial accounting to provide a basis for determining equity across type (of biodiversity), space, and time. We introduce net present biodiversity value (NPBV) as a theoretical and practical measure for defining the offset required to achieve no-net-loss. For evaluating equity in type and space we use measures of biodiversity value from systematic conservation planning. Time discount rates are used to address risk of non-repayment, and loss of utility. We illustrate these concepts and measures with two examples of biodiversity impact-offset transactions. Considerable further work is required to understand the characteristics of these approaches.

Measuring coseismic displacements with point-like targets offset tracking

KAUST Repository

Hu, Xie; Wang, Teng; Liao, Mingsheng

2014-01-01

Offset tracking is an important complement to measure large ground displacements in both azimuth and range dimensions where synthetic aperture radar (SAR) interferometry is unfeasible. Subpixel offsets can be obtained by searching for the cross-correlation peak calculated from the match patches uniformly distributed on two SAR images. However, it has its limitations, including redundant computation and incorrect estimations on decorrelated patches. In this letter, we propose a simple strategy that performs offset tracking on detected point-like targets (PT). We first detect image patches within bright PT by using a sinc-like template from a single SAR image and then perform offset tracking on them to obtain the pixel shifts. Compared with the standard method, the application on the 2010 M 7.2 El Mayor-Cucapah earthquake shows that the proposed PT offset tracking can significantly increase the cross-correlation and thus result in both efficiency and reliability improvements. © 2013 IEEE.

Analysis of induced seismicity in geothermal reservoirs – An overview

Science.gov (United States)

Zang, Arno; Oye, Volker; Jousset, Philippe; Deichmann, Nicholas; Gritto, Roland; McGarr, Arthur F.; Majer, Ernest; Bruhn, David

2014-01-01

In this overview we report results of analysing induced seismicity in geothermal reservoirs in various tectonic settings within the framework of the European Geothermal Engineering Integrating Mitigation of Induced Seismicity in Reservoirs (GEISER) project. In the reconnaissance phase of a field, the subsurface fault mapping, in situ stress and the seismic network are of primary interest in order to help assess the geothermal resource. The hypocentres of the observed seismic events (seismic cloud) are dependent on the design of the installed network, the used velocity model and the applied location technique. During the stimulation phase, the attention is turned to reservoir hydraulics (e.g., fluid pressure, injection volume) and its relation to larger magnitude seismic events, their source characteristics and occurrence in space and time. A change in isotropic components of the full waveform moment tensor is observed for events close to the injection well (tensile character) as compared to events further away from the injection well (shear character). Tensile events coincide with high Gutenberg-Richter b-values and low Brune stress drop values. The stress regime in the reservoir controls the direction of the fracture growth at depth, as indicated by the extent of the seismic cloud detected. Stress magnitudes are important in multiple stimulation of wells, where little or no seismicity is observed until the previous maximum stress level is exceeded (Kaiser Effect). Prior to drilling, obtaining a 3D P-wave (Vp) and S-wave velocity (Vs) model down to reservoir depth is recommended. In the stimulation phase, we recommend to monitor and to locate seismicity with high precision (decametre) in real-time and to perform local 4D tomography for velocity ratio (Vp/Vs). During exploitation, one should use observed and model induced seismicity to forward estimate seismic hazard so that field operators are in a position to adjust well hydraulics (rate and volume of the

Advancing New 3D Seismic Interpretation Methods for Exploration and Development of Fractured Tight Gas Reservoirs

Energy Technology Data Exchange (ETDEWEB)

James Reeves

2005-01-31

In a study funded by the U.S. Department of Energy and GeoSpectrum, Inc., new P-wave 3D seismic interpretation methods to characterize fractured gas reservoirs are developed. A data driven exploratory approach is used to determine empirical relationships for reservoir properties. Fractures are predicted using seismic lineament mapping through a series of horizon and time slices in the reservoir zone. A seismic lineament is a linear feature seen in a slice through the seismic volume that has negligible vertical offset. We interpret that in regions of high seismic lineament density there is a greater likelihood of fractured reservoir. Seismic AVO attributes are developed to map brittle reservoir rock (low clay) and gas content. Brittle rocks are interpreted to be more fractured when seismic lineaments are present. The most important attribute developed in this study is the gas sensitive phase gradient (a new AVO attribute), as reservoir fractures may provide a plumbing system for both water and gas. Success is obtained when economic gas and oil discoveries are found. In a gas field previously plagued with poor drilling results, four new wells were spotted using the new methodology and recently drilled. The wells have estimated best of 12-months production indicators of 2106, 1652, 941, and 227 MCFGPD. The latter well was drilled in a region of swarming seismic lineaments but has poor gas sensitive phase gradient (AVO) and clay volume attributes. GeoSpectrum advised the unit operators that this location did not appear to have significant Lower Dakota gas before the well was drilled. The other three wells are considered good wells in this part of the basin and among the best wells in the area. These new drilling results have nearly doubled the gas production and the value of the field. The interpretation method is ready for commercialization and gas exploration and development. The new technology is adaptable to conventional lower cost 3D seismic surveys.

Reservoir Changes Derived from Seismic Observations at The Geysers Geothermal Field, CA, USA

Science.gov (United States)

Gritto, R.; Jarpre, S.

2012-04-01

. Vertical depth-sections indicate that these low values are co-located with production zones and production related seismicity. In contrast, the highest Vp/Vs estimates are co-located with injection zones and their associated seismicity.

Field investigation of mining-induced seismicity on local geohydrology

International Nuclear Information System (INIS)

Hsiung, S.M.; Chowdhury, A.H.; Philip, J.; Blake, W.

1993-01-01

Hydraulic response of the rock mass due to earthquakes is one of the concerns in the assessment of the long-term performance of a repository. Studies performed by other researchers indicated no systematic difference between natural earthquakes and mining-induced seismic events. The purpose of this field study at the Lucky Friday Mine is intended to obtain a better understanding regarding the local geohydrologic changes due to mining-induced seismicity and to evaluate analytical methods for simulation of these changes. Three saturated zones with faults and vein features were packed-off along a borehole drilled at approximately 20 degrees downward in a southerly direction from a depth about 1,737 m (5,700 ft) below surface for water pressure monitoring. The response of water pressure change to mine seismicity is found to be more pronounced in Zone 3, which contains the Lucky Friday Main Vein, than Zone 2, with the South Control Fault, and Zone 1, with the associated fractures parallel to the South Control Fault. The maximum observed pressure increase in Zone 3 was about 1.53 x 10 -2 MPa (2.22 psi) due to a seismic event of Richter drops in Zone 1 resulting from a number of seismic events are suspected to be related to slips along the associated fractures of the South Control Fault, or the South Control Fault itself, which initiated the seismic events. Water pressure increase in Zone 3 was found to be a function of event magnitude and distance

12 CFR 1704.29 - Coordinating salary offset with other agencies.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 7 2010-01-01 2010-01-01 false Coordinating salary offset with other agencies... HOUSING AND URBAN DEVELOPMENT OFHEO ORGANIZATION AND FUNCTIONS DEBT COLLECTION Salary Offset § 1704.29 Coordinating salary offset with other agencies. (a) Responsibility of OFHEO as the creditor agency. (1) OFHEO...

Coulomb Failure Stress Accumulation in Nepal After the 2015 Mw 7.8 Gorkha Earthquake: Testing Earthquake Triggering Hypothesis and Evaluating Seismic Hazards

Science.gov (United States)

Xiong, N.; Niu, F.

2017-12-01

A Mw 7.8 earthquake struck Gorkha, Nepal, on April 5, 2015, resulting in more than 8000 deaths and 3.5 million homeless. The earthquake initiated 70km west of Kathmandu and propagated eastward, rupturing an area of approximately 150km by 60km in size. However, the earthquake failed to fully rupture the locked fault beneath the Himalaya, suggesting that the region south of Kathmandu and west of the current rupture are still locked and a much more powerful earthquake might occur in future. Therefore, the seismic hazard of the unruptured region is of great concern. In this study, we investigated the Coulomb failure stress (CFS) accumulation on the unruptured fault transferred by the Gorkha earthquake and some nearby historical great earthquakes. First, we calculated the co-seismic CFS changes of the Gorkha earthquake on the nodal planes of 16 large aftershocks to quantitatively examine whether they were brought closer to failure by the mainshock. It is shown that at least 12 of the 16 aftershocks were encouraged by an increase of CFS of 0.1-3 MPa. The correspondence between the distribution of off-fault aftershocks and the increased CFS pattern also validates the applicability of the earthquake triggering hypothesis in the thrust regime of Nepal. With the validation as confidence, we calculated the co-seismic CFS change on the locked region imparted by the Gorkha earthquake and historical great earthquakes. A newly proposed ramp-flat-ramp-flat fault geometry model was employed, and the source parameters of historical earthquakes were computed with the empirical scaling relationship. A broad region south of the Kathmandu and west of the current rupture were shown to be positively stressed with CFS change roughly ranging between 0.01 and 0.5 MPa. The maximum of CFS increase (>1MPa) was found in the updip segment south of the current rupture, implying a high seismic hazard. Since the locked region may be additionally stressed by the post-seismic relaxation of the lower

Slope Stability Analysis In Seismic Areas Of The Northern Apennines (Italy)

International Nuclear Information System (INIS)

Lo Presti, D.; Fontana, T.; Marchetti, D.

2008-01-01

Several research works have been published on the slope stability in the northern Tuscany (central Italy) and particularly in the seismic areas of Garfagnana and Lunigiana (Lucca and Massa-Carrara districts), aimed at analysing the slope stability under static and dynamic conditions and mapping the landslide hazard. In addition, in situ and laboratory investigations are available for the study area, thanks to the activities undertaken by the Tuscany Seismic Survey. Based on such a huge information the co-seismic stability of few ideal slope profiles have been analysed by means of Limit equilibrium method LEM - (pseudo-static) and Newmark sliding block analysis (pseudo-dynamic). The analysis--results gave indications about the most appropriate seismic coefficient to be used in pseudo-static analysis after establishing allowable permanent displacement. Such indications are commented in the light of the Italian and European prescriptions for seismic stability analysis with pseudo-static approach. The stability conditions, obtained from the previous analyses, could be used to define microzonation criteria for the study area

5 CFR 1639.28 - Coordinating salary offset with other agencies.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Coordinating salary offset with other... CLAIMS COLLECTION Salary Offset § 1639.28 Coordinating salary offset with other agencies. (a... employee is in the process of separating and has not received a final salary check or other final payment(s...

Statistical determination of significant curved I-girder bridge seismic response parameters

Science.gov (United States)

Seo, Junwon

2013-06-01

Curved steel bridges are commonly used at interchanges in transportation networks and more of these structures continue to be designed and built in the United States. Though the use of these bridges continues to increase in locations that experience high seismicity, the effects of curvature and other parameters on their seismic behaviors have been neglected in current risk assessment tools. These tools can evaluate the seismic vulnerability of a transportation network using fragility curves. One critical component of fragility curve development for curved steel bridges is the completion of sensitivity analyses that help identify influential parameters related to their seismic response. In this study, an accessible inventory of existing curved steel girder bridges located primarily in the Mid-Atlantic United States (MAUS) was used to establish statistical characteristics used as inputs for a seismic sensitivity study. Critical seismic response quantities were captured using 3D nonlinear finite element models. Influential parameters from these quantities were identified using statistical tools that incorporate experimental Plackett-Burman Design (PBD), which included Pareto optimal plots and prediction profiler techniques. The findings revealed that the potential variation in the influential parameters included number of spans, radius of curvature, maximum span length, girder spacing, and cross-frame spacing. These parameters showed varying levels of influence on the critical bridge response.

Seismic isolation of plants at risk of a severe accident

International Nuclear Information System (INIS)

Forni, Massimo

2015-01-01

More and more devastating earthquakes struck every year our planet. Many of these, though occurring in areas considered at high risk of earthquakes, far exceed the levels required by law. The industrial plants subjected to risk of severe accident, in particular petrochemical and nuclear power plants, are particularly exposed to this risk because of the number and the complexity of the structures and critical components of which they are composed. For this type of structures, anti-seismic techniques able to provide complete protection, even in case of unforeseen events, are needed. Seismic isolation is certainly the most promising technology of modern antiseismic as it allows not only to significantly reduce the dynamic load acting on the structures in case of seismic attack, but to provide safety margins against violent earthquakes, exceeding the assumed maximum design limit. [it

Attention capture by contour onsets and offsets: no special role for onsets.

Science.gov (United States)

Watson, D G; Humphreys, G W

1995-07-01

In five experiments, we investigated the power of targets defined by the onset or offset of one of an object's parts (contour onsets and offsets) either to guide or to capture visual attention. In Experiment 1, search for a single contour onset target was compared with search for a single contour offset target against a static background of distractors; no difference was found between the efficiency with which each could be detected. In Experiment 2, onsets and offsets were compared for automatic attention capture, when both occurred simultaneously. Unlike in previous studies, the effects of overall luminance change, new-object creation, and number of onset and offset items were controlled. It was found that contour onset and offset items captured attention equally well. However, display size effects on both target types were also apparent. Such effects may have been due to competition for selection between multiple onset and offset stimuli. In Experiments 3 and 4, single onset and offset stimuli were presented simultaneously and pitted directly against one another among a background of static distractors. In Experiment 3, we examined "guided search," for a target that was formed either from an onset or from an offset among static items. In Experiment 4, the onsets and offsets were uncorrelated with the target location. Similar results occurred in both experiments: target onsets and offsets were detected more efficiently than static stimuli which needed serial search; there remained effects of display size on performance; but there was still no advantage for onsets. In Experiment 5, we examined automatic attention capture by single onset and offset stimuli presented individually among static distractors. Again, there was no advantage for onset over offset targets and a display size effect was also present. These results suggest that, both in isolation and in competition, onsets that do not form new objects neither guide nor gain automatic attention more efficiently

Study on structural seismic margin and probabilistic seismic risk. Development of a structural capacity-seismic risk diagram

International Nuclear Information System (INIS)

Nakajima, Masato; Ohtori, Yasuki; Hirata, Kazuta

2010-01-01

Seismic margin is extremely important index and information when we evaluate and account seismic safety of critical structures, systems and components quantitatively. Therefore, it is required that electric power companies evaluate the seismic margin of each plant in back-check of nuclear power plants in Japan. The seismic margin of structures is usually defined as a structural capacity margin corresponding to design earthquake ground motion. However, there is little agreement as to the definition of the seismic margin and we have no knowledge about a relationship between the seismic margin and seismic risk (annual failure probability) which is obtained in PSA (Probabilistic Safety Assessment). The purpose of this report is to discuss a definition of structural seismic margin and to develop a diagram which can identify a relation between seismic margin and seismic risk. The main results of this paper are described as follows: (1) We develop seismic margin which is defined based on the fact that intensity of earthquake ground motion is more appropriate than the conventional definition (i.e., the response-based seismic margin) for the following reasons: -seismic margin based on earthquake ground motion is invariant where different typed structures are considered, -stakeholders can understand the seismic margin based on the earthquake ground motion better than the response-based one. (2) The developed seismic margin-risk diagram facilitates us to judge easily whether we need to perform detailed probabilistic risk analysis or only deterministic analysis, given that the reference risk level although information on the uncertainty parameter beta is not obtained. (3) We have performed numerical simulations based on the developed method for four sites in Japan. The structural capacity-risk diagram differs depending on each location because the diagram is greatly influenced by seismic hazard information for a target site. Furthermore, the required structural capacity