Evaluation of maximum allowable temperature inside basket of dry storage module for CANDU spent fuel
Lee, Kyung Ho; Yoon, Jeong Hyoun; Chae, Kyoung Myoung; Choi, Byung Il; Lee, Heung Young; Song, Myung Jae [Nuclear Environment Technology Institute, Taejon (Korea, Republic of); Cho, Gyu Seong [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of)
2002-10-01
This study provides a maximum allowable fuel temperature through a preliminary evaluation of the UO{sub 2} weight gain that may occur on a failed (breached sheathing) element of a fuel bundle. Intact bundles would not be affected as the UO{sub 2} would not be in contact with the air for the fuel storage basket. The analysis is made for the MACSTOR/KN-400 to be operated in Wolsong ambient air temperature conditions. The design basis fuel is a 6-year cooled fuel bundle that, on average has reached a burnup of 7,800 MWd/MTU. The fuel bundle considered for analysis is assumed to have a high burnup of 12,000 MWd/MTU and be located in a hot basket. The MACSTOR/KN-400 has the same air circuit as the MACSTOR and the air circuit will require a slightly higher temperature difference to exit the increased heat load. The maximum temperature of a high burnup bundle stored in the new MACSTOR/KN-400 is expected to be about 9 .deg. C higher than the fuel temperature of the MACSTOR at an equivalent constant ambient temperature. This temperature increase will in turn increase the UO{sub 2} weight gain from 0.06% (MACSTOR for Wolsong conditions) to an estimated 0.13% weight gain for the MACSTOR/KN-400. Compared to an acceptable UO{sub 2} weight gain of 0.6%, we are thus expecting to maintain a very acceptable safety factor of 4 to 5 for the new module against unacceptable stresses in the fuel sheathing. For the UO{sub 2} weight gain, the maximum allowable fuel temperature was shown by 164 .deg. C.
Dobranich, D.
1987-08-01
Calculations were performed to determine the mass of a space-based platform as a function of the maximum-allowed operating temperature of the electrical equipment within the platform payload. Two computer programs were used in conjunction to perform these calculations. The first program was used to determine the mass of the platform reactor, shield, and power conversion system. The second program was used to determine the mass of the main and secondary radiators of the platform. The main radiator removes the waste heat associated with the power conversion system and the secondary radiator removes the waste heat associated with the platform payload. These calculations were performed for both Brayton and Rankine cycle platforms with two different types of payload cooling systems: a pumped-loop system (a heat exchanger with a liquid coolant) and a refrigerator system. The results indicate that increases in the maximum-allowed payload temperature offer significant platform mass savings for both the Brayton and Rankine cycle platforms with either the pumped-loop or refrigerator payload cooling systems. Therefore, with respect to platform mass, the development of high temperature electrical equipment would be advantageous. 3 refs., 24 figs., 7 tabs.
49 CFR 230.24 - Maximum allowable stress.
2010-10-01
... 49 Transportation 4 2010-10-01 2010-10-01 false Maximum allowable stress. 230.24 Section 230.24... Allowable Stress § 230.24 Maximum allowable stress. (a) Maximum allowable stress value. The maximum allowable stress value on any component of a steam locomotive boiler shall not exceed 1/4 of the ultimate...
2011-01-10
...: Establishing Maximum Allowable Operating Pressure or Maximum Operating Pressure Using Record Evidence, and... facilities of their responsibilities, under Federal integrity management (IM) regulations, to perform... system, especially when calculating Maximum Allowable Operating Pressure (MAOP) or Maximum Operating...
32 CFR 842.35 - Depreciation and maximum allowances.
2010-07-01
... 32 National Defense 6 2010-07-01 2010-07-01 false Depreciation and maximum allowances. 842.35... LITIGATION ADMINISTRATIVE CLAIMS Personnel Claims (31 U.S.C. 3701, 3721) § 842.35 Depreciation and maximum allowances. The military services have jointly established the “Allowance List-Depreciation Guide”...
49 CFR 174.86 - Maximum allowable operating speed.
2010-10-01
... 49 Transportation 2 2010-10-01 2010-10-01 false Maximum allowable operating speed. 174.86 Section... operating speed. (a) For molten metals and molten glass shipped in packagings other than those prescribed in § 173.247 of this subchapter, the maximum allowable operating speed may not exceed 24 km/hour (15...
Scientific substantination of maximum allowable concentration of fluopicolide in water
Pelo I.М.
2014-03-01
Full Text Available In order to substantiate fluopicolide maximum allowable concentration in the water of water reservoirs the research was carried out. Methods of study: laboratory hygienic experiment using organoleptic and sanitary-chemical, sanitary-toxicological, sanitary-microbiological and mathematical methods. The results of fluopicolide influence on organoleptic properties of water, sanitary regimen of reservoirs for household purposes were given and its subthreshold concentration in water by sanitary and toxicological hazard index was calculated. The threshold concentration of the substance by the main hazard criteria was established, the maximum allowable concentration in water was substantiated. The studies led to the following conclusions: fluopicolide threshold concentration in water by organoleptic hazard index (limiting criterion – the smell – 0.15 mg/dm3, general sanitary hazard index (limiting criteria – impact on the number of saprophytic microflora, biochemical oxygen demand and nitrification – 0.015 mg/dm3, the maximum noneffective concentration – 0.14 mg/dm3, the maximum allowable concentration - 0.015 mg/dm3.
Maximum Allowable Dynamic Load of Mobile Manipulators with Stability Consideration
Heidary H. R.
2015-09-01
Full Text Available High payload to mass ratio is one of the advantages of mobile robot manipulators. In this paper, a general formula for finding the maximum allowable dynamic load (MADL of wheeled mobile robot is presented. Mobile manipulators operating in field environments will be required to manipulate large loads, and to perform such tasks on uneven terrain, which may cause the system to reach dangerous tip-over instability. Therefore, the method is expanded for finding the MADL of mobile manipulators with stability consideration. Moment-Height Stability (MHS criterion is used as an index for the system stability. Full dynamic model of wheeled mobile base and mounted manipulator is considered with respect to the dynamic of non-holonomic constraint. Then, a method for determination of the maximum allowable loads is described, subject to actuator constraints and by imposing the stability limitation as a new constraint. The actuator torque constraint is applied by using a speed-torque characteristics curve of a typical DC motor. In order to verify the effectiveness of the presented algorithm, several simulation studies considering a two-link planar manipulator, mounted on a mobile base are presented and the results are discussed.
Method to Determine Maximum Allowable Sinterable Silver Interconnect Size
Wereszczak, A. A.; Modugno, M. C.; Waters, S. B.; DeVoto, D. J.; Paret, P. P.
2016-05-01
The use of sintered-silver for large-area interconnection is attractive for some large-area bonding applications in power electronics such as the bonding of metal-clad, electrically-insulating substrates to heat sinks. Arrays of different pad sizes and pad shapes have been considered for such large area bonding; however, rather than arbitrarily choosing their size, it is desirable to use the largest size possible where the onset of interconnect delamination does not occur. If that is achieved, then sintered-silver's high thermal and electrical conductivities can be fully taken advantage of. Toward achieving this, a simple and inexpensive proof test is described to identify the largest achievable interconnect size with sinterable silver. The method's objective is to purposely initiate failure or delamination. Copper and invar (a ferrous-nickel alloy whose coefficient of thermal expansion (CTE) is similar to that of silicon or silicon carbide) disks were used in this study and sinterable silver was used to bond them. As a consequence of the method's execution, delamination occurred in some samples during cooling from the 250 degrees C sintering temperature to room temperature and bonding temperature and from thermal cycling in others. These occurrences and their interpretations highlight the method's utility, and the herein described results are used to speculate how sintered-silver bonding will work with other material combinations.
47 CFR 65.700 - Determining the maximum allowable rate of return.
2010-10-01
... CARRIER SERVICES (CONTINUED) INTERSTATE RATE OF RETURN PRESCRIPTION PROCEDURES AND METHODOLOGIES Maximum Allowable Rates of Return § 65.700 Determining the maximum allowable rate of return. (a) The maximum allowable rate of return for any exchange carrier's earnings on any access service category shall...
46 CFR 52.01-55 - Increase in maximum allowable working pressure.
2010-10-01
... 46 Shipping 2 2010-10-01 2010-10-01 false Increase in maximum allowable working pressure. 52.01-55... POWER BOILERS General Requirements § 52.01-55 Increase in maximum allowable working pressure. (a) When the maximum allowable working pressure of a boiler has been established, an increase in the pressure...
Maximum Temperature Detection System for Integrated Circuits
Frankiewicz, Maciej; Kos, Andrzej
2015-03-01
The paper describes structure and measurement results of the system detecting present maximum temperature on the surface of an integrated circuit. The system consists of the set of proportional to absolute temperature sensors, temperature processing path and a digital part designed in VHDL. Analogue parts of the circuit where designed with full-custom technique. The system is a part of temperature-controlled oscillator circuit - a power management system based on dynamic frequency scaling method. The oscillator cooperates with microprocessor dedicated for thermal experiments. The whole system is implemented in UMC CMOS 0.18 μm (1.8 V) technology.
Recommended Maximum Temperature For Mars Returned Samples
Beaty, D. W.; McSween, H. Y.; Czaja, A. D.; Goreva, Y. S.; Hausrath, E.; Herd, C. D. K.; Humayun, M.; McCubbin, F. M.; McLennan, S. M.; Hays, L. E.
2016-01-01
The Returned Sample Science Board (RSSB) was established in 2015 by NASA to provide expertise from the planetary sample community to the Mars 2020 Project. The RSSB's first task was to address the effect of heating during acquisition and storage of samples on scientific investigations that could be expected to be conducted if the samples are returned to Earth. Sample heating may cause changes that could ad-versely affect scientific investigations. Previous studies of temperature requirements for returned mar-tian samples fall within a wide range (-73 to 50 degrees Centigrade) and, for mission concepts that have a life detection component, the recommended threshold was less than or equal to -20 degrees Centigrade. The RSSB was asked by the Mars 2020 project to determine whether or not a temperature requirement was needed within the range of 30 to 70 degrees Centigrade. There are eight expected temperature regimes to which the samples could be exposed, from the moment that they are drilled until they are placed into a temperature-controlled environment on Earth. Two of those - heating during sample acquisition (drilling) and heating while cached on the Martian surface - potentially subject samples to the highest temperatures. The RSSB focused on the upper temperature limit that Mars samples should be allowed to reach. We considered 11 scientific investigations where thermal excursions may have an adverse effect on the science outcome. Those are: (T-1) organic geochemistry, (T-2) stable isotope geochemistry, (T-3) prevention of mineral hydration/dehydration and phase transformation, (T-4) retention of water, (T-5) characterization of amorphous materials, (T-6) putative Martian organisms, (T-7) oxidation/reduction reactions, (T-8) (sup 4) He thermochronometry, (T-9) radiometric dating using fission, cosmic-ray or solar-flare tracks, (T-10) analyses of trapped gasses, and (T-11) magnetic studies.
COMPASS' new magnet is placed inside the experiment, which will allow for maximum acceptance
Maximilien Brice
2005-01-01
A new magnet at CERN is going to allow COMPASS (Common Muon Proton Apparatus for Structure and Spectroscopy) maximum acceptance. Thanks to the 5 tonne, 2.5 m long magnet, which arrived last December, many more events are expected compared to the previous data-taking
2012-09-13
... Paperwork Reduction Act (44 U.S.C. 3501 et seq.); Is certified as not having a significant economic impact... into the new Missouri rule include: --10 CSR 10-2.040, Maximum Allowable Emission of Particulate Matter from Fuel Burning Equipment Used for Indirect Heating, for the Kansas City Metropolitan Area; --10 CSR...
49 CFR 192.619 - Maximum allowable operating pressure: Steel or plastic pipelines.
2010-10-01
... operate a segment of steel or plastic pipeline at a pressure that exceeds a maximum allowable operating... design pressure of the weakest element in the segment, determined in accordance with subparts C and D of... K of this part, if any variable necessary to determine the design pressure under the design...
2010-10-01
... distribution systems. (a) No person may operate a low-pressure distribution system at a pressure high enough to...) No person may operate a low pressure distribution system at a pressure lower than the minimum... 49 Transportation 3 2010-10-01 2010-10-01 false Maximum and minimum allowable operating...
49 CFR 192.621 - Maximum allowable operating pressure: High-pressure distribution systems.
2010-10-01
... STANDARDS Operations § 192.621 Maximum allowable operating pressure: High-pressure distribution systems. (a) No person may operate a segment of a high pressure distribution system at a pressure that exceeds the... segment of a distribution system otherwise designed to operate at over 60 p.s.i. (414 kPa) gage,...
Iammarino, Marco; Di Taranto, Aurelia; Muscarella, Marilena
2012-02-01
Sulphiting agents are commonly used food additives. They are not allowed in fresh meat preparations. In this work, 2250 fresh meat samples were analysed to establish the maximum concentration of sulphites that can be considered as "natural" and therefore be admitted in fresh meat preparations. The analyses were carried out by an optimised Monier-Williams Method and the positive samples confirmed by ion chromatography. Sulphite concentrations higher than the screening method LOQ (10.0 mg · kg(-1)) were found in 100 samples. Concentrations higher than 76.6 mg · kg(-1), attributable to sulphiting agent addition, were registered in 40 samples. Concentrations lower than 41.3 mg · kg(-1) were registered in 60 samples. Taking into account the distribution of sulphite concentrations obtained, it is plausible to estimate a maximum allowable limit of 40.0 mg · kg(-1) (expressed as SO(2)). Below this value the samples can be considered as "compliant".
Lihui Guo
2015-01-01
Full Text Available With the increasing penetration of wind power, the randomness and volatility of wind power output would have a greater impact on safety and steady operation of power system. In allusion to the uncertainty of wind speed and load demand, this paper applied box set robust optimization theory in determining the maximum allowable installed capacity of wind farm, while constraints of node voltage and line capacity are considered. Optimized duality theory is used to simplify the model and convert uncertainty quantities in constraints into certainty quantities. Under the condition of multi wind farms, a bilevel optimization model to calculate penetration capacity is proposed. The result of IEEE 30-bus system shows that the robust optimization model proposed in the paper is correct and effective and indicates that the fluctuation range of wind speed and load and the importance degree of grid connection point of wind farm and load point have impact on the allowable capacity of wind farm.
16 CFR 1505.8 - Maximum acceptable material temperatures.
2010-01-01
... Association, 155 East 44th Street, New York, NY 10017. Material Degrees C. Degrees F. Capacitors (1) (1) Class... capacitor has no marked temperature limit, the maximum acceptable temperature will be assumed to be 65...
The Maximum Free Magnetic Energy Allowed in a Solar Active Region
Moore, Ronald L.; Falconer, David A.
2009-01-01
Two whole-active-region magnetic quantities that can be measured from a line-of-sight magnetogram are (sup L) WL(sub SG), a gauge of the total free energy in an active region's magnetic field, and sup L(sub theta), a measure of the active region's total magnetic flux. From these two quantities measured from 1865 SOHO/MDI magnetograms that tracked 44 sunspot active regions across the 0.5 R(sub Sun) central disk, together with each active region's observed production of CMEs, X flares, and M flares, Falconer et al (2009, ApJ, submitted) found that (1) active regions have a maximum attainable free magnetic energy that increases with the magnetic size (sup L) (sub theta) of the active region, (2) in (Log (sup L)WL(sub SG), Log(sup L) theta) space, CME/flare-productive active regions are concentrated in a straight-line main sequence along which the free magnetic energy is near its upper limit, and (3) X and M flares are restricted to large active regions. Here, from (a) these results, (b) the observation that even the greatest X flares produce at most only subtle changes in active region magnetograms, and (c) measurements from MSFC vector magnetograms and from MDI line-of-sight magnetograms showing that practically all sunspot active regions have nearly the same area-averaged magnetic field strength: =- theta/A approximately equal to 300 G, where theta is the active region's total photospheric flux of field stronger than 100 G and A is the area of that flux, we infer that (1) the maximum allowed ratio of an active region's free magnetic energy to its potential-field energy is 1, and (2) any one CME/flare eruption releases no more than a small fraction (less than 10%) of the active region's free magnetic energy. This work was funded by NASA's Heliophysics Division and NSF's Division of Atmospheric Sciences.
Impact of Maximum Allowable Cost on CO2 Storage Capacity in Saline Formations.
Mathias, Simon A; Gluyas, Jon G; Goldthorpe, Ward H; Mackay, Eric J
2015-11-17
Injecting CO2 into deep saline formations represents an important component of many greenhouse-gas-reduction strategies for the future. A number of authors have posed concern over the thousands of injection wells likely to be needed. However, a more important criterion than the number of wells is whether the total cost of storing the CO2 is market-bearable. Previous studies have sought to determine the number of injection wells required to achieve a specified storage target. Here an alternative methodology is presented whereby we specify a maximum allowable cost (MAC) per ton of CO2 stored, a priori, and determine the corresponding potential operational storage capacity. The methodology takes advantage of an analytical solution for pressure build-up during CO2 injection into a cylindrical saline formation, accounting for two-phase flow, brine evaporation, and salt precipitation around the injection well. The methodology is applied to 375 saline formations from the U.K. Continental Shelf. Parameter uncertainty is propagated using Monte Carlo simulation with 10 000 realizations for each formation. The results show that MAC affects both the magnitude and spatial distribution of potential operational storage capacity on a national scale. Different storage prospects can appear more or less attractive depending on the MAC scenario considered. It is also shown that, under high well-injection rate scenarios with relatively low cost, there is adequate operational storage capacity for the equivalent of 40 years of U.K. CO2 emissions.
Estimation of Maximum Allowable PV Connection to LV Residential Power Networks
Demirok, Erhan; Sera, Dezso; Teodorescu, Remus
2011-01-01
transformer or using solar inverters with new grid support features. This study presents a methodology for the estimation of maximum PV hosting capacity including IEC 60076-7 based thermal model of distribution transformer. Certain part of a real distribution network of Braedstrup suburban area in Denmark...... is used in simulation as a case study model. Furthermore, varying solutions (utilizing thermally upgraded insulation paper in transformers, reactive power services from solar inverters, etc.) are implemented on the network under investigation to examine PV penetration level and finally key results learnt......Maximum photovoltaic (PV) hosting capacity of low voltage (LV) power networks is mainly restricted by either thermal limits of network components or grid voltage quality resulted from high penetration of distributed PV systems. This maximum hosting capacity may be lower than the available solar...
Maximum entropy production allows a simple representation of heterogeneity in semiarid ecosystems.
Schymanski, Stanislaus J; Kleidon, Axel; Stieglitz, Marc; Narula, Jatin
2010-05-12
Feedbacks between water use, biomass and infiltration capacity in semiarid ecosystems have been shown to lead to the spontaneous formation of vegetation patterns in a simple model. The formation of patterns permits the maintenance of larger overall biomass at low rainfall rates compared with homogeneous vegetation. This results in a bias of models run at larger scales neglecting subgrid-scale variability. In the present study, we investigate the question whether subgrid-scale heterogeneity can be parameterized as the outcome of optimal partitioning between bare soil and vegetated area. We find that a two-box model reproduces the time-averaged biomass of the patterns emerging in a 100 x 100 grid model if the vegetated fraction is optimized for maximum entropy production (MEP). This suggests that the proposed optimality-based representation of subgrid-scale heterogeneity may be generally applicable to different systems and at different scales. The implications for our understanding of self-organized behaviour and its modelling are discussed.
Eun-Chan Kim
2016-06-01
Full Text Available The International Convention for the Control and Management of Ships’ Ballast Water and Sediments was adopted by IMO (International Maritime Organization on 13 February 2004. Fifty-seven ballast water management systems were granted basic approval of active substance by IMO, among which thirty-seven systems were granted final approval. This paper studies the maximum allowable dosage of active substances produced by ballast water management system using electrolysis which is an approved management system by IMO. The allowable dosage of active substances by electrolysis system is proposed by TRO (Total Residual Oxidant. Maximum allowable dosage of TRO is a very important factor in the ballast water management system when using the electrolysis methods, because ballast water management system is controlled with the TRO value, and the IMO approvals are given on the basis of the maximum allowable dosage of TRO for the treatment and discharge of ballast water. However, between various management systems approved TRO concentration of maximum allowable dosage showed large differences, ranging from 1 to 15 ppm, depending on the management systems. The discrepancies of maximum allowable dosage among the management systems may depend on whether a filter is used or not, the difference in the specifications of the electrolysis module, the kind of the tested organisms, the number of individual organisms, and the difference in the water quality, etc. Ship owners are responsible for satisfying the performance standard of the IMO convention in the ports of each country therefore need to carefully review whether the ballast water management system can satisfy the performance standard of the IMO convention or not.
Mroczka Janusz
2014-12-01
Full Text Available Photovoltaic panels have a non-linear current-voltage characteristics to produce the maximum power at only one point called the maximum power point. In the case of the uniform illumination a single solar panel shows only one maximum power, which is also the global maximum power point. In the case an irregularly illuminated photovoltaic panel many local maxima on the power-voltage curve can be observed and only one of them is the global maximum. The proposed algorithm detects whether a solar panel is in the uniform insolation conditions. Then an appropriate strategy of tracking the maximum power point is taken using a decision algorithm. The proposed method is simulated in the environment created by the authors, which allows to stimulate photovoltaic panels in real conditions of lighting, temperature and shading.
CMB Maximum Temperature Asymmetry Axis: Alignment with Other Cosmic Asymmetries
Mariano, Antonio
2012-01-01
We use a global pixel based estimator to identify the axis of the residual Maximum Temperature Asymmetry (MTA) (after the dipole subtraction) of the WMAP 7 year Internal Linear Combination (ILC) CMB temperature sky map. The estimator is based on considering the temperature differences between opposite pixels in the sky at various angular resolutions (4 degrees-15 degrees and selecting the axis that maximizes this difference. We consider three large scale Healpix resolutions (N_{side}=16 (3.7 degrees), N_{side}=8 (7.3 degrees) and N_{side}=4 (14.7 degrees)). We compare the direction and magnitude of this asymmetry with three other cosmic asymmetry axes (\\alpha dipole, Dark Energy Dipole and Dark Flow) and find that the four asymmetry axes are abnormally close to each other. We compare the observed MTA axis with the corresponding MTA axes of 10^4 Gaussian isotropic simulated ILC maps (based on LCDM). The fraction of simulated ILC maps that reproduces the observed magnitude of the MTA asymmetry and alignment wit...
Impact of soil moisture on extreme maximum temperatures in Europe
Kirien Whan
2015-09-01
Full Text Available Land-atmosphere interactions play an important role for hot temperature extremes in Europe. Dry soils may amplify such extremes through feedbacks with evapotranspiration. While previous observational studies generally focused on the relationship between precipitation deficits and the number of hot days, we investigate here the influence of soil moisture (SM on summer monthly maximum temperatures (TXx using water balance model-based SM estimates (driven with observations and temperature observations. Generalized extreme value distributions are fitted to TXx using SM as a covariate. We identify a negative relationship between SM and TXx, whereby a 100 mm decrease in model-based SM is associated with a 1.6 °C increase in TXx in Southern-Central and Southeastern Europe. Dry SM conditions result in a 2–4 °C increase in the 20-year return value of TXx compared to wet conditions in these two regions. In contrast with SM impacts on the number of hot days (NHD, where low and high surface-moisture conditions lead to different variability, we find a mostly linear dependency of the 20-year return value on surface-moisture conditions. We attribute this difference to the non-linear relationship between TXx and NHD that stems from the threshold-based calculation of NHD. Furthermore the employed SM data and the Standardized Precipitation Index (SPI are only weakly correlated in the investigated regions, highlighting the importance of evapotranspiration and runoff for resulting SM. Finally, in a case study for the hot 2003 summer we illustrate that if 2003 spring conditions in Southern-Central Europe had been as dry as in the more recent 2011 event, temperature extremes in summer would have been higher by about 1 °C, further enhancing the already extreme conditions which prevailed in that year.
Gómez, I.; Estrela, M.
2009-09-01
Extreme temperature events have a great impact on human society. Knowledge of summer maximum temperatures is very useful for both the general public and organisations whose workers have to operate in the open, e.g. railways, roadways, tourism, etc. Moreover, summer maximum daily temperatures are considered a parameter of interest and concern since persistent heat-waves can affect areas as diverse as public health, energy consumption, etc. Thus, an accurate forecasting of these temperatures could help to predict heat-wave conditions and permit the implementation of strategies aimed at minimizing the negative effects that high temperatures have on human health. The aim of this work is to evaluate the skill of the RAMS model in determining daily maximum temperatures during summer over the Valencia Region. For this, we have used the real-time configuration of this model currently running at the CEAM Foundation. To carry out the model verification process, we have analysed not only the global behaviour of the model for the whole Valencia Region, but also its behaviour for the individual stations distributed within this area. The study has been performed for the summer forecast period of 1 June - 30 September, 2007. The results obtained are encouraging and indicate a good agreement between the observed and simulated maximum temperatures. Moreover, the model captures quite well the temperatures in the extreme heat episodes. Acknowledgement. This work was supported by "GRACCIE" (CSD2007-00067, Programa Consolider-Ingenio 2010), by the Spanish Ministerio de Educación y Ciencia, contract number CGL2005-03386/CLI, and by the Regional Government of Valencia Conselleria de Sanitat, contract "Simulación de las olas de calor e invasiones de frío y su regionalización en la Comunidad Valenciana" ("Heat wave and cold invasion simulation and their regionalization at Valencia Region"). The CEAM Foundation is supported by the Generalitat Valenciana and BANCAIXA (Valencia, Spain).
无
2011-01-01
[Objective] The research aimed to analyze temporal and spatial variation characteristics of temperature in Shangqiu City during 1961-2010.[Method] Based on temperature data in eight meteorological stations of Shangqiu during 1961-2010,by using trend analysis method,the temporal and spatial evolution characteristics of annual average temperature,annual average maximum and minimum temperatures,annual extreme maximum and minimum temperatures,daily range of annual average temperature in Shangqiu City were analy...
Decadal trends in Red Sea maximum surface temperature
Chaidez, Veronica
2017-08-09
Ocean warming is a major consequence of climate change, with the surface of the ocean having warmed by 0.11 °C decade-1 over the last 50 years and is estimated to continue to warm by an additional 0.6 - 2.0 °C before the end of the century1. However, there is considerable variability in the rates experienced by different ocean regions, so understanding regional trends is important to inform on possible stresses for marine organisms, particularly in warm seas where organisms may be already operating in the high end of their thermal tolerance. Although the Red Sea is one of the warmest ecosystems on earth, its historical warming trends and thermal evolution remain largely understudied. We characterized the Red Sea\\'s thermal regimes at the basin scale, with a focus on the spatial distribution and changes over time of sea surface temperature maxima, using remotely sensed sea surface temperature data from 1982 - 2015. The overall rate of warming for the Red Sea is 0.17 ± 0.07 °C decade-1, while the northern Red Sea is warming between 0.40 and 0.45 °C decade-1, all exceeding the global rate. Our findings show that the Red Sea is fast warming, which may in the future challenge its organisms and communities.
无
2008-01-01
Ecological systems in the headwaters of the Yellow River, characterized by hash natural environmental conditions, are very vulnerable to climatic change. In the most recent decades, this area greatly attracted the public's attention for its more and more deteriorating environmental conditions. Based on tree-ring samples from the Xiqing Mountain and A'nyêmagên Mountains at the headwaters of the Yellow River in the Northeastern Tibetan Plateau, we reconstructed the minimum temperatures in the winter half year over the last 425 years and the maximum temperatures in the summer half year over the past 700 years in this region. The variation of minimum temperature in the winter half year during the time span of 1578-1940 was a relatively stable trend, which was followed by an abrupt warming trend since 1941. However, there is no significant warming trend for the maximum temperature in the summer half year over the 20th century. The asymmetric variation patterns between the minimum and maximum temperatures were observed in this study over the past 425 years. During the past 425 years, there are similar variation patterns between the minimum and maximum temperatures; however, the minimum temperatures vary about 25 years earlier compared to the maximum temperatures. If such a trend of variation patterns between the minimum and maximum temperatures over the past 425 years continues in the future 30 years, the maximum temperature in this region will increase significantly.
Jacoby; GORDON
2008-01-01
Ecological systems in the headwaters of the Yellow River, characterized by hash natural environmental conditions, are very vulnerable to climatic change. In the most recent decades, this area greatly attracted the public’s attention for its more and more deteriorating environmental conditions. Based on tree-ring samples from the Xiqing Mountain and A’nyêmagên Mountains at the headwaters of the Yellow River in the Northeastern Tibetan Plateau, we reconstructed the minimum temperatures in the winter half year over the last 425 years and the maximum temperatures in the summer half year over the past 700 years in this region. The variation of minimum temperature in the winter half year during the time span of 1578―1940 was a relatively stable trend, which was followed by an abrupt warming trend since 1941. However, there is no significant warming trend for the maximum temperature in the summer half year over the 20th century. The asymmetric variation patterns between the minimum and maximum temperatures were observed in this study over the past 425 years. During the past 425 years, there are similar variation patterns between the minimum and maximum temperatures; however, the minimum temperatures vary about 25 years earlier compared to the maximum temperatures. If such a trend of variation patterns between the minimum and maximum temperatures over the past 425 years continues in the future 30 years, the maximum temperature in this region will increase significantly.
Esfandiar, Habib; KoraYem, Moharam Habibnejad [Islamic Azad University, Tehran (Iran, Islamic Republic of)
2015-09-15
In this study, the researchers try to examine nonlinear dynamic analysis and determine Dynamic load carrying capacity (DLCC) in flexible manipulators. Manipulator modeling is based on Timoshenko beam theory (TBT) considering the effects of shear and rotational inertia. To get rid of the risk of shear locking, a new procedure is presented based on mixed finite element formulation. In the method proposed, shear deformation is free from the risk of shear locking and independent of the number of integration points along the element axis. Dynamic modeling of manipulators will be done by taking into account small and large deformation models and using extended Hamilton method. System motion equations are obtained by using nonlinear relationship between displacements-strain and 2nd PiolaKirchoff stress tensor. In addition, a comprehensive formulation will be developed to calculate DLCC of the flexible manipulators during the path determined considering the constraints end effector accuracy, maximum torque in motors and maximum stress in manipulators. Simulation studies are conducted to evaluate the efficiency of the method proposed taking two-link flexible and fixed base manipulators for linear and circular paths into consideration. Experimental results are also provided to validate the theoretical model. The findings represent the efficiency and appropriate performance of the method proposed.
On the magnitude of temperature decrease in the equatorial regions during the Last Glacial Maximum
王宁练; 姚檀栋; 施雅风; L.G.Thompson; J.Cole-Dai; P.-N.Lin; and; M.E.Davis
1999-01-01
Based on the data of temperature changes revealed by means of various palaeothermometric proxy indices,it is found that the magnitude of temperature decrease became large with altitude in the equatorial regions during the Last Glacial Maximum. The direct cause of this phenomenon was the change in temperature lapse rate, which was about(0.1±0.05)℃/100 m larger in the equator during the Last Glacial Maximum than at present. Moreover, the analyses show that CLIMAP possibly underestimated the sea surface temperature decrease in the equatorial regions during the Last Glacial Maximum.
Daniel, G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Rudisill, T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)
2017-07-17
As part of the Spent Nuclear Fuel (SNF) processing campaign, H-Canyon is planning to begin dissolving High Flux Isotope Reactor (HFIR) fuel in late FY17 or early FY18. Each HFIR fuel core contains inner and outer fuel elements which were fabricated from uranium oxide (U_{3}O_{8}) dispersed in a continuous Al phase using traditional powder metallurgy techniques. Fuels fabricated in this manner, like other SNF’s processed in H-Canyon, dissolve by the same general mechanisms with similar gas generation rates and the production of H_{2}. The HFIR fuel cores will be dissolved using a flowsheet developed by the Savannah River National Laboratory (SRNL) in either the 6.4D or 6.1D dissolver using a unique insert. Multiple cores will be charged to the same dissolver solution maximizing the concentration of dissolved Al. The recovered U will be down-blended into low-enriched U for subsequent use as commercial reactor fuel. During the development of the HFIR fuel dissolution flowsheet, the cycle time for the initial core was estimated at 28 to 40 h. Once the cycle is complete, H-Canyon personnel will open the dissolver and probe the HFIR insert wells to determine the height of any fuel fragments which did not dissolve. Before the next core can be charged to the dissolver, an analysis of the potential for H_{2} gas generation must show that the combined surface area of the fuel fragments and the subsequent core will not generate H_{2} concentrations in the dissolver offgas which exceeds 60% of the lower flammability limit (LFL) of H_{2} at 200 °C. The objective of this study is to identify the maximum fuel fragment height as a function of the Al concentration in the dissolving solution which will provide criteria for charging successive HFIR cores to an H-Canyon dissolver.
Observed Abrupt Changes in Minimum and Maximum Temperatures in Jordan in the 20th Century
Mohammad M. samdi
2006-01-01
Full Text Available This study examines changes in annual and seasonal mean (minimum and maximum temperatures variations in Jordan during the 20th century. The analyses focus on the time series records at the Amman Airport Meteorological (AAM station. The occurrence of abrupt changes and trends were examined using cumulative sum charts (CUSUM and bootstrapping and the Mann-Kendall rank test. Statistically significant abrupt changes and trends have been detected. Major change points in the mean minimum (night-time and mean maximum (day-time temperatures occurred in 1957 and 1967, respectively. A minor change point in the annual mean maximum temperature also occurred in 1954, which is essential agreement with the detected change in minimum temperature. The analysis showed a significant warming trend after the years 1957 and 1967 for the minimum and maximum temperatures, respectively. The analysis of maximum temperatures shows a significant warming trend after the year 1967 for the summer season with a rate of temperature increase of 0.038°C/year. The analysis of minimum temperatures shows a significant warming trend after the year 1957 for all seasons. Temperature and rainfall data from other stations in the country have been considered and showed similar changes.
Eldridge, Jeffrey I. (Inventor); Chambers, Matthew D. (Inventor)
2014-01-01
Systems and methods that are capable of measuring pressure or temperature based on luminescence are discussed herein. These systems and methods are based on spin-allowed broadband luminescence of sensors with orthorhombic perovskite structures of rare earth aluminates doped with chromium or similar transition metals, such as chromium-doped gadolinium aluminate. Luminescence from these sensors can be measured to determine at least one of temperature or pressure, based on either the intense luminescence of these sensors, even at high temperatures, or low temperature techniques discussed herein.
Temple R. Lee
2014-01-01
Full Text Available Downscaling future temperature projections to mountainous regions is vital for many applications, including ecological and water resource management. In this study, we demonstrate a method to downscale maximum temperatures to subkilometer resolutions using the Parameter-elevation Regression on Independent Slopes Model (PRISM. We evaluate the downscaling method with observations from a network of temperature sensors deployed along western and eastern slopes of Virginia’s Shenandoah National Park in the southern Appalachian Mountains. We find that the method overestimates mean July maximum temperatures by about 2°C (4°C along the western (eastern slopes. Based on this knowledge, we introduce corrections to generate maps of current and future maximum temperatures in the Shenandoah National Park.
Variability of maximum and mean average temperature across Libya (1945-2009)
Ageena, I.; Macdonald, N.; Morse, A. P.
2014-08-01
Spatial and temporal variability in daily maximum and mean average daily temperature, monthly maximum and mean average monthly temperature for nine coastal stations during the period 1956-2009 (54 years), and annual maximum and mean average temperature for coastal and inland stations for the period 1945-2009 (65 years) across Libya are analysed. During the period 1945-2009, significant increases in maximum temperature (0.017 °C/year) and mean average temperature (0.021 °C/year) are identified at most stations. Significantly, warming in annual maximum temperature (0.038 °C/year) and mean average annual temperatures (0.049 °C/year) are observed at almost all study stations during the last 32 years (1978-2009). The results show that Libya has witnessed a significant warming since the middle of the twentieth century, which will have a considerable impact on societies and the ecology of the North Africa region, if increases continue at current rates.
Shifts in the temperature of maximum density (TMD) of ionic liquid aqueous solutions.
Tariq, M; Esperança, J M S S; Soromenho, M R C; Rebelo, L P N; Lopes, J N Canongia
2013-07-14
This work investigates for the first time shifts in the temperature of maximum density (TMD) of water caused by ionic liquid solutes. A vast amount of high-precision volumetric data--more than 6000 equilibrated (static) high-precision density determination corresponding to ∼90 distinct ionic liquid aqueous solutions of 28 different types of ionic liquid--allowed us to analyze the TMD shifts for different homologous series or similar sets of ionic solutes and explain the overall effects in terms of hydrophobic, electrostatic and hydrogen-bonding contributions. The differences between the observed TMD shifts in the -2 temperatures are discussed taking into account the different types of possible solute-water interactions that can modify the structure of the aqueous phase. The results also reveal different insights concerning the nature of the ions that constitute typical ionic liquids and are consistent with previous results that established hydrophobic and hydrophilic scales for ionic liquid ions based on their specific interactions with water and other probe molecules.
A hybrid solar panel maximum power point search method that uses light and temperature sensors
Ostrowski, Mariusz
2016-04-01
Solar cells have low efficiency and non-linear characteristics. To increase the output power solar cells are connected in more complex structures. Solar panels consist of series of connected solar cells with a few bypass diodes, to avoid negative effects of partial shading conditions. Solar panels are connected to special device named the maximum power point tracker. This device adapt output power from solar panels to load requirements and have also build in a special algorithm to track the maximum power point of solar panels. Bypass diodes may cause appearance of local maxima on power-voltage curve when the panel surface is illuminated irregularly. In this case traditional maximum power point tracking algorithms can find only a local maximum power point. In this article the hybrid maximum power point search algorithm is presented. The main goal of the proposed method is a combination of two algorithms: a method that use temperature sensors to track maximum power point in partial shading conditions and a method that use illumination sensor to track maximum power point in equal illumination conditions. In comparison to another methods, the proposed algorithm uses correlation functions to determinate the relationship between values of illumination and temperature sensors and the corresponding values of current and voltage in maximum power point. In partial shading condition the algorithm calculates local maximum power points bases on the value of temperature and the correlation function and after that measures the value of power on each of calculated point choose those with have biggest value, and on its base run the perturb and observe search algorithm. In case of equal illumination algorithm calculate the maximum power point bases on the illumination value and the correlation function and on its base run the perturb and observe algorithm. In addition, the proposed method uses a special coefficient modification of correlation functions algorithm. This sub
How do GCMs represent daily maximum and minimum temperatures in La Plata Basin?
Bettolli, M. L.; Penalba, O. C.; Krieger, P. A.
2013-05-01
This work focuses on southern La Plata Basin region which is one of the most important agriculture and hydropower producing regions worldwide. Extreme climate events such as cold and heat waves and frost events have a significant socio-economic impact. It is a big challenge for global climate models (GCMs) to simulate regional patterns, temporal variations and distribution of temperature in a daily basis. Taking into account the present and future relevance of the region for the economy of the countries involved, it is very important to analyze maximum and minimum temperatures for model evaluation and development. This kind of study is aslo the basis for a great deal of the statistical downscaling methods in a climate change context. The aim of this study is to analyze the ability of the GCMs to reproduce the observed daily maximum and minimum temperatures in the southern La Plata Basin region. To this end, daily fields of maximum and minimum temperatures from a set of 15 GCMs were used. The outputs corresponding to the historical experiment for the reference period 1979-1999 were obtained from the WCRP CMIP5 (World Climate Research Programme Coupled Model Intercomparison Project Phase 5). In order to compare daily temperature values in the southern La Plata Basin region as generated by GCMs to those derived from observations, daily maximum and minimum temperatures were used from the gridded dataset generated by the Claris LPB Project ("A Europe-South America Network for Climate Change Assessment and Impact Studies in La Plata Basin"). Additionally, reference station data was included in the study. The analysis was focused on austral winter (June, July, August) and summer (December, January, February). The study was carried out by analyzing the performance of the 15 GCMs , as well as their ensemble mean, in simulating the probability distribution function (pdf) of maximum and minimum temperatures which include mean values, variability, skewness, et c, and regional
Vladimir Kendrovski
2011-01-01
Full Text Available Background: Higher temperatures have been associated with higher salmonellosis notifications worldwide. Aims : The objective of this paper is to assess the seasonal pattern of Salmonella cases among humans. Material and Methods: The relationship between ambient maximum temperature and reports of confirmed cases of Salmonella in the Republic of Macedonia and Skopje during the summer months (i.e. June, July, August and September beginning in 1998 through 2008 was investigated. The monthly number of reported Salmonella cases and ambient maximum temperatures for Skopje were related to the national number of cases and temperatures recorded during the same timeframe using regression statistical analyses. The Poisson regression model was adapted for the analysis of the data. Results: While a decreasing tendency was registered at the national level, the analysis for Skopje showed an increasing tendency for registration of new salmonella cases. Reported incidents of salmonellosis, were positively associated (P<0.05 with temperature during the summer months. By increasing of the maximum monthly mean temperature of 1° C in Skopje, the salmonellosis incidence increased by 5.2% per month. Conclusions: The incidence of Salmonella cases in the Macedonian population varies seasonally: the highest values of the Seasonal Index for Salmonella cases were registered in the summer months, i.e. June, July, August and September.
谢松光; 杨红生; 周毅; 张福绥
2004-01-01
Maximum rate of food consumption (Cmax) was determined for juvenile Sebastodes fuscescens (Houttuyn) at water temperature of 10, 15, 20 and 25℃. The relationships of Cmax to the body weight (W) at each temperature were described by a power equation: lnCmax = a + b lnW. Covariance analysis revealed significant interaction of the temperature and body weight. The relationship of adjusted Cmax to water temperature (T) was described by a quadratic equation: Cmax =-0.369 + 0.456T - 0.0117T2. The optimal feeding temperature calculated from this equation was 19.5℃. The coefficients of the multiple regression estimation relating Cmax to body weight (W) and water temperature (T) were given in the Table 2.
Trends in Mean Annual Minimum and Maximum Near Surface Temperature in Nairobi City, Kenya
George Lukoye Makokha
2010-01-01
Full Text Available This paper examines the long-term urban modification of mean annual conditions of near surface temperature in Nairobi City. Data from four weather stations situated in Nairobi were collected from the Kenya Meteorological Department for the period from 1966 to 1999 inclusive. The data included mean annual maximum and minimum temperatures, and was first subjected to homogeneity test before analysis. Both linear regression and Mann-Kendall rank test were used to discern the mean annual trends. Results show that the change of temperature over the thirty-four years study period is higher for minimum temperature than maximum temperature. The warming trends began earlier and are more significant at the urban stations than is the case at the sub-urban stations, an indication of the spread of urbanisation from the built-up Central Business District (CBD to the suburbs. The established significant warming trends in minimum temperature, which are likely to reach higher proportions in future, pose serious challenges on climate and urban planning of the city. In particular the effect of increased minimum temperature on human physiological comfort, building and urban design, wind circulation and air pollution needs to be incorporated in future urban planning programmes of the city.
Man, E. A.; Sera, D.; Mathe, L.; Schaltz, E.; Rosendahl, L.
2016-03-01
Characterization of thermoelectric generators (TEG) is widely discussed and equipment has been built that can perform such analysis. One method is often used to perform such characterization: constant temperature with variable thermal power input. Maximum power point tracking (MPPT) methods for TEG systems are mostly tested under steady-state conditions for different constant input temperatures. However, for most TEG applications, the input temperature gradient changes, exposing the MPPT to variable tracking conditions. An example is the exhaust pipe on hybrid vehicles, for which, because of the intermittent operation of the internal combustion engine, the TEG and its MPPT controller are exposed to a cyclic temperature profile. Furthermore, there are no guidelines on how fast the MPPT must be under such dynamic conditions. In the work discussed in this paper, temperature gradients for TEG integrated in several applications were evaluated; the results showed temperature variation up to 5°C/s for TEG systems. Electrical characterization of a calcium-manganese oxide TEG was performed at steady-state for different input temperatures and a maximum temperature of 401°C. By using electrical data from characterization of the oxide module, a solar array simulator was emulated to perform as a TEG. A trapezoidal temperature profile with different gradients was used on the TEG simulator to evaluate the dynamic MPPT efficiency. It is known that the perturb and observe (P&O) algorithm may have difficulty accurately tracking under rapidly changing conditions. To solve this problem, a compromise must be found between the magnitude of the increment and the sampling frequency of the control algorithm. The standard P&O performance was evaluated experimentally by using different temperature gradients for different MPPT sampling frequencies, and efficiency values are provided for all cases. The results showed that a tracking speed of 2.5 Hz can be successfully implemented on a TEG
Estimating minimum and maximum air temperature using MODIS data over Indo-Gangetic Plain
D B Shah; M R Pandya; H J Trivedi; A R Jani
2013-12-01
Spatially distributed air temperature data are required for climatological, hydrological and environmental studies. However, high spatial distribution patterns of air temperature are not available from meteorological stations due to its sparse network. The objective of this study was to estimate high spatial resolution minimum air temperature (min) and maximum air temperature (max) over the Indo-Gangetic Plain using Moderate Resolution Imaging Spectroradiometer (MODIS) data and India Meteorological Department (IMD) ground station data. min was estimated by establishing an empirical relationship between IMD min and night-time MODIS Land Surface Temperature (s). While, max was estimated using the Temperature-Vegetation Index (TVX) approach. The TVX approach is based on the linear relationship between s and Normalized Difference Vegetation Index (NDVI) data where max is estimated by extrapolating the NDVI-s regression line to maximum value of NDVImax for effective full vegetation cover. The present study also proposed a methodology to estimate NDVImax using IMD measured max for the Indo-Gangetic Plain. Comparison of MODIS estimated min with IMD measured min showed mean absolute error (MAE) of 1.73°C and a root mean square error (RMSE) of 2.2°C. Analysis in the study for max estimation showed that calibrated NDVImax performed well, with the MAE of 1.79°C and RMSE of 2.16°C.
MARSpline model for lead seven-day maximum and minimum air temperature prediction in Chennai, India
K Ramesh; R Anitha
2014-06-01
In this study, a Multivariate Adaptive Regression Spline (MARS) based lead seven days minimum and maximum surface air temperature prediction system is modelled for station Chennai, India. To emphasize the effectiveness of the proposed system, comparison is made with the models created using statistical learning technique Support Vector Machine Regression (SVMr). The analysis highlights that prediction accuracy of MARS models for minimum temperature forecast are promising for short-term forecast (lead days 1 to 3) with mean absolute error (MAE) less than 1°C and the prediction efficiency and skill degrades in medium term forecast (lead days 4 to 7) with slightly above 1°C. The MAE of maximum temperature is little higher than minimum temperature forecast varying from 0.87°C for day-one to 1.27°C for lag day-seven with MARS approach. The statistical error analysis emphasizes that MARS models perform well with an average 0.2°C of reduction in MAE over SVMr models for all ahead seven days and provide significant guidance for the prediction of temperature event. The study also suggests that the correlation between the atmospheric parameters used as predictors and the temperature event decreases as the lag increases with both approaches.
The maximum efficiency of nano heat engines depends on more than temperature
Woods, Mischa; Ng, Nelly; Wehner, Stephanie
Sadi Carnot's theorem regarding the maximum efficiency of heat engines is considered to be of fundamental importance in the theory of heat engines and thermodynamics. Here, we show that at the nano and quantum scale, this law needs to be revised in the sense that more information about the bath other than its temperature is required to decide whether maximum efficiency can be achieved. In particular, we derive new fundamental limitations of the efficiency of heat engines at the nano and quantum scale that show that the Carnot efficiency can only be achieved under special circumstances, and we derive a new maximum efficiency for others. A preprint can be found here arXiv:1506.02322 [quant-ph] Singapore's MOE Tier 3A Grant & STW, Netherlands.
Temperature dependence of attitude sensor coalignments on the Solar Maximum Mission (SMM)
Pitone, D. S.; Eudell, A. H.; Patt, F. S.
1990-01-01
The temperature correlation of the relative coalignment between the fine-pointing sun sensor and fixed-head star trackers measured on the Solar Maximum Mission (SMM) is analyzed. An overview of the SMM, including mission history and configuration, is given. Possible causes of the misalignment variation are discussed, with focus placed on spacecraft bending due to solar-radiation pressure, electronic or mechanical changes in the sensors, uncertainty in the attitude solutions, and mounting-plate expansion and contraction due to thermal effects. Yaw misalignment variation from the temperature profile is assessed, and suggestions for spacecraft operations are presented, involving methods to incorporate flight measurements of the temperature-versus-alignment function and its variance in operational procedures and the spacecraft structure temperatures in the attitude telemetry record.
Arkharov, A. M.; Dontsova, E. S.; Lavrov, N. A.; Romanovskii, V. R.
2014-04-01
Maximum allowable (ultimate) currents stably passing through an YBa2Cu3O7 superconducting current-carrying element are determined as a function of a silver (or copper) coating thickness, external magnetic field induction, and cooling conditions. It is found that if a magnetic system based on yttrium ceramics is cooled by a cryogenic coolant, currents causing instabilities (instability onset currents) are almost independent of the coating thickness. If, however, liquid helium is used as a cooling agent, the ultimate current monotonically grows with the thickness of the stabilizing copper coating. It is shown that depending on cooling conditions, the stable values of the current and electric field strength preceding the occurrence of instability may be both higher and lower than the a priori chosen critical parameters of the superconductor. These features should be taken into account in selecting the stable value of the operating current of YBa2Cu3O7 superconducting windings.
Felis, Thomas; McGregor, Helen V; Linsley, Braddock K; Tudhope, Alexander W; Gagan, Michael K; Suzuki, Atsushi; Inoue, Mayuri; Thomas, Alexander L; Esat, Tezer M; Thompson, William G; Tiwari, Manish; Potts, Donald C; Mudelsee, Manfred; Yokoyama, Yusuke; Webster, Jody M
2014-06-17
Tropical south-western Pacific temperatures are of vital importance to the Great Barrier Reef (GBR), but the role of sea surface temperatures (SSTs) in the growth of the GBR since the Last Glacial Maximum remains largely unknown. Here we present records of Sr/Ca and δ(18)O for Last Glacial Maximum and deglacial corals that show a considerably steeper meridional SST gradient than the present day in the central GBR. We find a 1-2 °C larger temperature decrease between 17° and 20°S about 20,000 to 13,000 years ago. The result is best explained by the northward expansion of cooler subtropical waters due to a weakening of the South Pacific gyre and East Australian Current. Our findings indicate that the GBR experienced substantial meridional temperature change during the last deglaciation, and serve to explain anomalous deglacial drying of northeastern Australia. Overall, the GBR developed through significant SST change and may be more resilient than previously thought.
Barrows, Timothy T.; Juggins, Steve
2005-04-01
We present new last glacial maximum (LGM) sea-surface temperature (SST) maps for the oceans around Australia based on planktonic foraminifera assemblages. To provide the most reliable SST estimates we use the modern analog technique, the revised analog method, and artificial neural networks in conjunction with an expanded modern core top database. All three methods produce similar quality predictions and the root mean squared error of the consensus prediction (the average of the three) under cross-validation is only ±0.77 °C. We determine LGM SST using data from 165 cores, most of which have good age control from oxygen isotope stratigraphy and radiocarbon dates. The coldest SST occurred at 20,500±1400 cal yr BP, predating the maximum in oxygen isotope records at 18,200±1500 cal yr BP. During the LGM interval we observe cooling within the tropics of up to 4 °C in the eastern Indian Ocean, and mostly between 0 and 3 °C elsewhere along the equator. The high latitudes cooled by the greatest degree, a maximum of 7-9 °C in the southwest Pacific Ocean. Our maps improve substantially on previous attempts by making higher quality temperature estimates, using more cores, and improving age control.
DSC “peak temperature” versus “maximum slope temperature” in determining TSSD temperature
Khatamian, D.
2010-10-01
One of the concerns of the nuclear industry is the deleterious effect of hydrogen on the structural integrity of the reactor core components due to delayed hydride cracking (DHC). The DHC process occurs when hydrogen concentration exceeds the terminal solid solubility (TSS) in the component. Thus, the accurate knowledge of TSS is necessary to predict the lifetime of the components. Differential scanning calorimetry (DSC) is normally used to measure the hydrogen TSS in zirconium alloys. There is a measurable change in the amount of heat absorbed by the specimen when the hydrides dissolve. The hydride dissolution process does not exhibit a well-defined "sharp" change in the heat-flow signal at the transition temperature. A typical DSC heat-flow curve for hydride dissolution has three definite features; "peak temperature" (PT), "maximum slope temperature" (MST) and "completion temperature". The present investigation aims to identify the part of the heat-flow signal that closely corresponds to the TSS temperature for hydride dissolution ( TTSSD). Coupons were cut from a Zr-2.5Nb specimen, which had been previously hydrided using an electrolytic cell to create a surface hydride layer of ˜20 μm thick on all sides of the specimen. The coupons were then annealed isothermally at various temperatures to establish the TTSSD under equilibrium conditions. Subsequently the hydride layer was removed and the coupons were analyzed for TSSD temperature using DSC. The PT and MST for each DSC run were determined and compared to the annealing temperature of the coupon. The results show that the annealing temperature (the equilibrium TTSSD) is much closer to the DSC PT than any other feature of the heat-flow curve.
Improved Determination of the Location of the Temperature Maximum in the Corona
Lemaire, J. F.; Stegen, K.
2016-12-01
The most used method to calculate the coronal electron temperature [Te (r)] from a coronal density distribution [ne (r)] is the scale-height method (SHM). We introduce a novel method that is a generalization of a method introduced by Alfvén ( Ark. Mat. Astron. Fys. 27, 1, 1941) to calculate Te(r) for a corona in hydrostatic equilibrium: the "HST" method. All of the methods discussed here require given electron-density distributions [ne (r)] which can be derived from white-light (WL) eclipse observations. The new "DYN" method determines the unique solution of Te(r) for which Te(r → ∞) → 0 when the solar corona expands radially as realized in hydrodynamical solar-wind models. The applications of the SHM method and DYN method give comparable distributions for Te(r). Both have a maximum [T_{max}] whose value ranges between 1 - 3 MK. However, the peak of temperature is located at a different altitude in both cases. Close to the Sun where the expansion velocity is subsonic (r < 1.3 R_{⊙}) the DYN method gives the same results as the HST method. The effects of the other free parameters on the DYN temperature distribution are presented in the last part of this study. Our DYN method is a new tool to evaluate the range of altitudes where the heating rate is maximum in the solar corona when the electron-density distribution is obtained from WL coronal observations.
Balakirev, Fedor F [Los Alamos National Laboratory; Migliori, A [MPA-NHMFL; Riggs, S [NHMFL-FSU; Hunte, F [NHMFL-FSU; Gurevich, A [NHMFL-FSU; Larbalestier, D [NHMFL-FSU; Boebinger, G [NHMFL-FSU; Jaroszynski, J [NHMFL-FSU; Ren, Z [CHINA; Lu, W [CHINA; Yang, J [CHINA; Shen, X [CHINA; Dong, X [CHINA; Zhao, Z [CHINA; Jin, R [ORNL; Sefat, A [ORNL; Mcguire, M [ORNL; Sales, B [ORNL; Christen, D [ORNL; Mandrus, D [ORNL
2008-01-01
We compare magnetotransport of the three iron-arsenide-based compounds ReFeAsO (Re=La, Sm, Nd) in very high DC and pulsed magnetic fields up to 45 and 54 T, respectively. Each sample studied exhibits a superconducting transition temperature near the maximum reported to date for that particular compound. While high magnetic fields do not suppress the superconducting state appreciably, the resistivity, Hall coefficient, and critical magnetic fields, taken together, suggest that the phenomenology and superconducting parameters of the oxypnictide superconductors bridges the gap between MgB{sub 2} and YBCO.
Probing Ionic Liquid Aqueous Solutions Using Temperature of Maximum Density Isotope Effects
Mohammad Tariq
2013-03-01
Full Text Available This work is a new development of an extensive research program that is investigating for the first time shifts in the temperature of maximum density (TMD of aqueous solutions caused by ionic liquid solutes. In the present case we have compared the shifts caused by three ionic liquid solutes with a common cation—1-ethyl-3-methylimidazolium coupled with acetate, ethylsulfate and tetracyanoborate anions—in normal and deuterated water solutions. The observed differences are discussed in terms of the nature of the corresponding anion-water interactions.
The Paleocene - Eocene Thermal Maximum: Temperature and Ecology in the Tropics
Frieling, J.; Gebhardt, H.; Adekeye, O. A.; Akande, S. O.; Reichart, G. J.; Middelburg, J. J. B. M.; Schouten, S.; Huber, M.; Sluijs, A.
2014-12-01
Various records across the Paleocene - Eocene Thermal Maximum (PETM) have established approximately 5 °C of additional surface and deep ocean warming, superimposed on the already warm latest Paleocene. The PETM is further characterized by a global negative stable carbon isotope excursion (CIE), poleward migration of thermophilic biota, ocean acidification, increased weathering, photic zone euxinia and intensified hydrological cycle. Reconstructed temperatures for the PETM in mid and high-latitudes regularly exceed modern open marine tropical temperatures. Constraints on absolute tropical temperatures are, however, limited. We studied the PETM in a sediment section from the Nigerian sector of the Dahomey Basin, deposited on the shelf near the equator. We estimate sea surface temperatures by paired analyses of TEX86, and Mg/Ca and δ18O of foraminifera from the Shagamu Quarry. These show Palaeocene temperatures of ~33 °C and SSTs rose by 4 °C during the PETM based on TEX86. During the PETM, intermittent photic zone euxinia developed based on the presence of the biomarker isorenieratane. Interestingly, during peak warmth, dinoflagellate cyst abundances and diversity are remarkably low. From our new data and evidence from modern dinoflagellate experiments, we conclude that thermal stress was the main driver for this observation. We derive that endothermal and most ectothermal nektonic and planktonic marine eukaryotic organisms could not have lived in the surface waters in this part of the tropics during the PETM.
Single Temperature Sensor Superheat Control Using a Novel Maximum Slope-seeking Method
Vinther, Kasper; Rasmussen, Henrik; Izadi-Zamanabadi, Roozbeh;
2013-01-01
Superheating of refrigerant in the evaporator is an important aspect of safe operation of refrigeration systems. The level of superheat is typically controlled by adjusting the flow of refrigerant using an electronic expansion valve, where the superheat is calculated using measurements from...... a pressure and a temperature sensor. In this paper we show, through extensive testing, that the superheat or filling of the evaporator can actually be controlled using only a single temperature sensor. This can either reduce commissioning costs by lowering the necessary amount of sensors or add fault...... tolerance in existing systems if a sensor fails (e.g. pressure sensor). The solution is based on a novel maximum slope-seeking control method, where a perturbation signal is added to the valve opening degree, which gives additional information about the system for control purposes. Furthermore, the method...
Verification of surface minimum, mean, and maximum temperature forecasts in Calabria for summer 2008
S. Federico
2011-02-01
Full Text Available Since 2005, one-hour temperature forecasts for the Calabria region (southern Italy, modelled by the Regional Atmospheric Modeling System (RAMS, have been issued by CRATI/ISAC-CNR (Consortium for Research and Application of Innovative Technologies/Institute for Atmospheric and Climate Sciences of the National Research Council and are available online at http://meteo.crati.it/previsioni.html (every six hours. Beginning in June 2008, the horizontal resolution was enhanced to 2.5 km. In the present paper, forecast skill and accuracy are evaluated out to four days for the 2008 summer season (from 6 June to 30 September, 112 runs. For this purpose, gridded high horizontal resolution forecasts of minimum, mean, and maximum temperatures are evaluated against gridded analyses at the same horizontal resolution (2.5 km.
Gridded analysis is based on Optimal Interpolation (OI and uses the RAMS first-day temperature forecast as the background field. Observations from 87 thermometers are used in the analysis system. The analysis error is introduced to quantify the effect of using the RAMS first-day forecast as the background field in the OI analyses and to define the forecast error unambiguously, while spatial interpolation (SI analysis is considered to quantify the statistics' sensitivity to the verifying analysis and to show the quality of the OI analyses for different background fields.
Two case studies, the first one with a low (less than the 10th percentile root mean square error (RMSE in the OI analysis, the second with the largest RMSE of the whole period in the OI analysis, are discussed to show the forecast performance under two different conditions. Cumulative statistics are used to quantify forecast errors out to four days. Results show that maximum temperature has the largest RMSE, while minimum and mean temperature errors are similar. For the period considered
Huang, Y X; Zhou, Q; Qiu, X; Shang, X D; Lu, Z M; Liu, and Y L
2014-01-01
In this paper, we introduce a new way to estimate the scaling parameter of a self-similar process by considering the maximum probability density function (pdf) of tis increments. We prove this for $H$-self-similar processes in general and experimentally investigate it for turbulent velocity and temperature increments. We consider turbulent velocity database from an experimental homogeneous and nearly isotropic turbulent channel flow, and temperature data set obtained near the sidewall of a Rayleigh-B\\'{e}nard convection cell, where the turbulent flow is driven by buoyancy. For the former database, it is found that the maximum value of increment pdf $p_{\\max}(\\tau)$ is in a good agreement with lognormal distribution. We also obtain a scaling exponent $\\alpha\\simeq 0.37$, which is consistent with the scaling exponent for the first-order structure function reported in other studies. For the latter one, we obtain a scaling exponent $\\alpha_{\\theta}\\simeq0.33$. This index value is consistent with the Kolmogorov-Ob...
N. Etien
2007-10-01
Full Text Available In this study, we have combined a Burgundy grape harvest date record with new δ^{18}O measurements conducted on timbers and living trees cellulose from Fontainebleau castle and forest. Our reconstruction is expected to provide a reference series for the variability of growing season temperature (from April to September in Western Europe from 1596 to 2000. We have estimated an uncertainty of 0.55°C on individual growing season maximum temperature reconstructions. We are able to assess this uncertainty, which is not the case for many documentary sources (diaries etc., and even not the case for early instrumental temperature data.
We compare our data with a number of independent temperature estimates for Europe and the Northern Hemisphere. The comparison between our reconstruction and Manley mean growing season temperature data provides an independent control of the quality of CET data. We show that our reconstruction preserves more variance back in time, because it was not distorted/averaged by statistical/homogenisation methods.
Further works will be conducted to compare the δ^{18}O data from wood cellulose provided by transects of different tree species in Europe obtained within the EC ISONET project and the French ANR Program ESCARSEL, to analyse the spatial and temporal coherency between δ^{18}O records. The decadal variability will be also compared with other precipitation δ^{18}O records such as those obtained from benthic ostracods from deep peri-Alpine lakes or simulated by regional atmospheric models equipped with the modelling of water stable isotopes.
Vaudrey, A; Lanzetta, F; Glises, R
2009-01-01
Producing useful electrical work in consuming chemical energy, the fuel cell have to reject heat to its surrounding. However, as it occurs for any other type of engine, this thermal energy cannot be exchanged in an isothermal way in finite time through finite areas. As it was already done for various types of systems, we study the fuel cell within the finite time thermodynamics framework and define an endoreversible fuel cell. Considering different types of heat transfer laws, we obtain an optimal value of the operating temperature, corresponding to a maximum produced power. This analysis is a first step of a thermodynamical approach of design of thermal management devices, taking into account performances of the whole system.
A new global reconstruction of temperature changes at the Last Glacial Maximum
J. D. Annan
2013-02-01
Full Text Available Some recent compilations of proxy data both on land and ocean (MARGO Project Members, 2009; Bartlein et al., 2011; Shakun et al., 2012, have provided a new opportunity for an improved assessment of the overall climatic state of the Last Glacial Maximum. In this paper, we combine these proxy data with the ensemble of structurally diverse state of the art climate models which participated in the PMIP2 project (Braconnot et al., 2007 to generate a spatially complete reconstruction of surface air (and sea surface temperatures. We test a variety of approaches, and show that multiple linear regression performs well for this application. Our reconstruction is significantly different to and more accurate than previous approaches and we obtain an estimated global mean cooling of 4.0 ± 0.8 °C (95% CI.
Foulger, G.R.
1995-01-01
Given a uniform lithology and strain rate and a full seismic data set, the maximum depth of earthquakes may be viewed to a first order as an isotherm. These conditions are approached at the Hengill geothermal area, S. Iceland, a dominantly basaltic area. The temperature at which seismic failure ceases for the strain rates likely at the Hengill geothermal area is determined by analogy with oceanic crust, and is about 650 ?? 50??C. The topographies of the top and bottom of the seismogenic layer were mapped using 617 earthquakes. The thickness of the seismogenic layer is roughly constant and about 3 km. A shallow, aseismic, low-velocity volume within the spreading plate boundary that crosses the area occurs above the top of the seismogenic layer and is interpreted as an isolated body of partial melt. The base of the seismogenic layer has a maximum depth of about 6.5 km beneath the spreading axis and deepens to about 7 km beneath a transform zone in the south of the area. -from Author
Sa-Correia, I.; Van Uden, N.
1983-06-01
Difficulties experienced by brewers with yeast performance in the brewing of lager at low temperatures has led the authors to study the effect of ethanol on the minimum temperature for growth (T. min). It has been found that both the maximum temperature (T max) and T min were adversely affected by ethanol and that ethanol tolerance prevailed at intermediate temperatures. (Refs. 8).
Improved Determination of the Location of the Temperature Maximum in the Corona
Lemaire, J. F.; Stegen, K.
2016-10-01
The most used method to calculate the coronal electron temperature [ Te (r)] from a coronal density distribution [ ne (r)] is the scale-height method (SHM). We introduce a novel method that is a generalization of a method introduced by Alfvén (Ark. Mat. Astron. Fys. 27, 1, 1941) to calculate Te(r) for a corona in hydrostatic equilibrium: the "HST" method. All of the methods discussed here require given electron-density distributions [ ne (r)] which can be derived from white-light (WL) eclipse observations. The new "DYN" method determines the unique solution of Te(r) for which Te(r → ∞) → 0 when the solar corona expands radially as realized in hydrodynamical solar-wind models. The applications of the SHM method and DYN method give comparable distributions for Te(r). Both have a maximum [ T_{max}] whose value ranges between 1 - 3 MK. However, the peak of temperature is located at a different altitude in both cases. Close to the Sun where the expansion velocity is subsonic ( r corona when the electron-density distribution is obtained from WL coronal observations.
Lussana, C.
2013-04-01
The presented work focuses on the investigation of gridded daily minimum (TN) and maximum (TX) temperature probability density functions (PDFs) with the intent of both characterising a region and detecting extreme values. The empirical PDFs estimation procedure has been realised using the most recent years of gridded temperature analysis fields available at ARPA Lombardia, in Northern Italy. The spatial interpolation is based on an implementation of Optimal Interpolation using observations from a dense surface network of automated weather stations. An effort has been made to identify both the time period and the spatial areas with a stable data density otherwise the elaboration could be influenced by the unsettled station distribution. The PDF used in this study is based on the Gaussian distribution, nevertheless it is designed to have an asymmetrical (skewed) shape in order to enable distinction between warming and cooling events. Once properly defined the occurrence of extreme events, it is possible to straightforwardly deliver to the users the information on a local-scale in a concise way, such as: TX extremely cold/hot or TN extremely cold/hot.
U.S. Geological Survey, Department of the Interior — This data set represents the average monthly maximum temperature in Celsius multiplied by 100 for 2002 compiled for every catchment of NHDPlus for the conterminous...
Climate change uncertainty for daily minimum and maximum temperatures: a model inter-comparison
Lobell, D; Bonfils, C; Duffy, P
2006-11-09
Several impacts of climate change may depend more on changes in mean daily minimum (T{sub min}) or maximum (T{sub max}) temperatures than daily averages. To evaluate uncertainties in these variables, we compared projections of T{sub min} and T{sub max} changes by 2046-2065 for 12 climate models under an A2 emission scenario. Average modeled changes in T{sub max} were slightly lower in most locations than T{sub min}, consistent with historical trends exhibiting a reduction in diurnal temperature ranges. However, while average changes in T{sub min} and T{sub max} were similar, the inter-model variability of T{sub min} and T{sub max} projections exhibited substantial differences. For example, inter-model standard deviations of June-August T{sub max} changes were more than 50% greater than for T{sub min} throughout much of North America, Europe, and Asia. Model differences in cloud changes, which exert relatively greater influence on T{sub max} during summer and T{sub min} during winter, were identified as the main source of uncertainty disparities. These results highlight the importance of considering separately projections for T{sub max} and T{sub min} when assessing climate change impacts, even in cases where average projected changes are similar. In addition, impacts that are most sensitive to summertime T{sub min} or wintertime T{sub max} may be more predictable than suggested by analyses using only projections of daily average temperatures.
Zhao Yang
2015-01-01
Full Text Available By using optical microscope (OM, scanning electron microscope (SEM, transmission electron microscope (TEM, X-ray diffraction (XRD, electron back scattered diffraction (EBSD and tensile test, the effect of annealing temperature on microstructure and mechanical properties of a high Al-low Si TRIP steel was investigated. The results show that TRIP effect can be obtained when annealing temperature is above Ac3 due to the existence of δ-ferrite in this high Al-low Si TRIP steel. That is to say, the microstructure consisting of ferrite, bainite and retained austenite can be obtained when annealing temperature is above Ac3. Furthermore, the tensile strength and the product of strength and elongation decrease with increasing annealing temperature when annealing temperature is above Ac3.
Surface chemistry allows for abiotic precipitation of dolomite at low temperature.
Roberts, Jennifer A; Kenward, Paul A; Fowle, David A; Goldstein, Robert H; González, Luis A; Moore, David S
2013-09-03
Although the mineral dolomite is abundant in ancient low-temperature sedimentary systems, it is scarce in modern systems below 50 °C. Chemical mechanism(s) enhancing its formation remain an enigma because abiotic dolomite has been challenging to synthesize at low temperature in laboratory settings. Microbial enhancement of dolomite precipitation at low temperature has been reported; however, it is still unclear exactly how microorganisms influence reaction kinetics. Here we document the abiotic synthesis of low-temperature dolomite in laboratory experiments and constrain possible mechanisms for dolomite formation. Ancient and modern seawater solution compositions, with identical pH and pCO2, were used to precipitate an ordered, stoichiometric dolomite phase at 30 °C in as few as 20 d. Mg-rich phases nucleate exclusively on carboxylated polystyrene spheres along with calcite, whereas aragonite forms in solution via homogeneous nucleation. We infer that Mg ions are complexed and dewatered by surface-bound carboxyl groups, thus decreasing the energy required for carbonation. These results indicate that natural surfaces, including organic matter and microbial biomass, possessing a high density of carboxyl groups may be a mechanism by which ordered dolomite nuclei form. Although environments rich in organic matter may be of interest, our data suggest that sharp biogeochemical interfaces that promote microbial death, as well as those with high salinity may, in part, control carboxyl-group density on organic carbon surfaces, consistent with origin of dolomites from microbial biofilms, as well as hypersaline and mixing zone environments.
New results on equatorial thermospheric winds and the midnight temperature maximum
Meriwether, J.; Faivre, M.; Fesen, C. [Clemson Univ., SC (United States). Dept. of Physics and Astronomy; Sherwood, P. [Interactive Technology, Waban, MA (United States); Veliz, O. [Inst. Geofisica del Peru, Lima (Peru). Radio Observatorio de Jicamarca
2008-07-01
Optical observations of thermospheric winds and temperatures determined with high resolution measurements of Doppler shifts and Doppler widths of the OI 630-nm equatorial nightglow emission have been made with improved accuracy at Arequipa, Peru (16.4 S, 71.4 W) with an imaging Fabry-Perot interferometer. An observing procedure previously used at Arecibo Observatory was applied to achieve increased spatial and temporal sampling of the thermospheric wind and temperature with the selection of eight azimuthal directions, equally spaced from 0 to 360 , at a zenith angle of 60 . By assuming the equivalence of longitude and local time, the data obtained using this technique is analyzed to determine the mean neutral wind speeds and mean horizontal gradients of the wind field in the zonal and meridional directions. The new temperature measurements obtained with the improved instrumental accuracy clearly show the midnight temperature maximum (MTM) peak with amplitudes of 25 to 200 K in all directions observed for most nights. The horizontal wind field maps calculated from the mean winds and gradients show the MTM peak is always preceded by an equatorward wind surge lasting 1-2 h. The results also show for winter events a meridional wind abatement seen after the MTM peak. On one occasion, near the September equinox, a reversal was observed during the poleward transit of the MTM over Arequipa. Analysis inferring vertical winds from the observed convergence yielded inconsistent results, calling into question the validity of this calculation for the MTM structure at equatorial latitudes during solar minimum. Comparison of the observations with the predictions of the NCAR general circulation model indicates that the model fails to reproduce the observed amplitude by a factor of 5 or more. This is attributed in part to the lack of adequate spatial resolution in the model as the MTM phenomenon takes place within a scale of 300-500 km and {proportional_to}45 min in local time. The
Jaagus, Jaak; Briede, Agrita; Rimkus, Egidijus; Remm, Kalle
2014-10-01
Spatial distribution and trends in mean and absolute maximum and minimum temperatures and in the diurnal temperature range were analysed at 47 stations in the eastern Baltic region (Lithuania, Latvia and Estonia) during 1951-2010. Dependence of the studied variables on geographical factors (latitude, the Baltic Sea, land elevation) is discussed. Statistically significant increasing trends in maximum and minimum temperatures were detected for March, April, July, August and annual values. At the majority of stations, the increase was detected also in February and May in case of maximum temperature and in January and May in case of minimum temperature. Warming was slightly higher in the northern part of the study area, i.e. in Estonia. Trends in the diurnal temperature range differ seasonally. The highest increasing trend revealed in April and, at some stations, also in May, July and August. Negative and mostly insignificant changes have occurred in January, February, March and June. The annual temperature range has not changed.
Morris, Jeffrey F.
2014-09-29
The main objective of the proposed work was the development and testing of a storage method that has the potential to fundamentally change the solar thermal industry. The development of a mathematical model that describes the phenomena involved in the heat storage and recovery was also a main objective of this work. Therefore, the goal was to prepare a design package allowing reliable scale-up and optimization of design.
Werner, Stefanie [Umweltbundesamt, Dessau-Rosslau (Germany). Fachgebiet II 2.3
2011-05-15
When offshore wind farms are constructed, every single pile is hammered into the sediment by a hydraulic hammer. Noise levels at Horns Reef wind farm were in the range of 235 dB. The noise may cause damage to the auditory system of marine mammals. The Federal Environmental Office therefore recommends the definition of maximum permissible noise levels. Further, care should be taken that no marine mammals are found in the immediate vicinity of the construction site. (AKB)
Wilson, Robert M.
2013-01-01
Examined are the annual averages, 10-year moving averages, decadal averages, and sunspot cycle (SC) length averages of the mean, maximum, and minimum surface air temperatures and the diurnal temperature range (DTR) for the Armagh Observatory, Northern Ireland, during the interval 1844-2012. Strong upward trends are apparent in the Armagh surface-air temperatures (ASAT), while a strong downward trend is apparent in the DTR, especially when the ASAT data are averaged by decade or over individual SC lengths. The long-term decrease in the decadaland SC-averaged annual DTR occurs because the annual minimum temperatures have risen more quickly than the annual maximum temperatures. Estimates are given for the Armagh annual mean, maximum, and minimum temperatures and the DTR for the current decade (2010-2019) and SC24.
Merino, Andrés; Martín, M. L.; Fernández-González, S.; Sánchez, J. L.; Valero, F.
2017-07-01
The aim of this paper is to analyze spatiotemporal distribution of maximum temperatures in the Iberian Peninsula (IP) by using various extreme maximum temperature indices. Thresholds for determining temperature extreme event (TEE) severity are defined using 99th percentiles of daily temperature time series for the period 1948 to 2009. The synoptic-scale fields of such events were analyzed in order to better understand the related atmospheric processes. The results indicate that the regions with a higher risk of maximum temperatures are located in the river valleys of southwest and northeast of the IP, while the Cantabrian coast and mountain ranges are characterized by lower risk. The TEEs were classified, by means of several synoptic fields (sea level pressure, temperature, and geopotential height at 850 and 500 hPa), in four clusters that largely explain their spatiotemporal distribution on the IP. The results of this study show that TEEs mainly occur associated with a ridge elongated from Subtropical areas. The relationships of TEEs with teleconnection patterns, such as the North Atlantic Oscillation (NAO), Western Mediterranean Oscillation (WeMO), and Mediterranean Oscillation (MO), showed that the interannual variability of extreme maximum temperatures is largely controlled by the dominant phase of WeMO in all seasons except wintertime where NAO is prevailing. Results related to MO pattern show less relevance in the maximum temperatures variability. The correct identification of synoptic patterns linked with the most extreme temperature event associated with each cluster will assist the prediction of events that can pose a natural hazard, thereby providing useful information for decision making and warning systems.
Zhu, Liangjun; Zhang, Yuandong; Li, Zongshan; Guo, Binde; Wang, Xiaochun
2016-07-01
We present a reconstruction of July-August mean maximum temperature variability based on a chronology of tree-ring widths over the period AD 1646-2013 in the northern part of the northwestern Sichuan Plateau (NWSP), China. A regression model explains 37.1 % of the variance of July-August mean maximum temperature during the calibration period from 1954 to 2012. Compared with nearby temperature reconstructions and gridded land surface temperature data, our temperature reconstruction had high spatial representativeness. Seven major cold periods were identified (1708-1711, 1765-1769, 1818-1821, 1824-1828, 1832-1836, 1839-1842, and 1869-1877), and three major warm periods occurred in 1655-1668, 1719-1730, and 1858-1859 from this reconstruction. The typical Little Ice Age climate can also be well represented in our reconstruction and clearly ended with climatic amelioration at the late of the 19th century. The 17th and 19th centuries were cold with more extreme cold years, while the 18th and 20th centuries were warm with less extreme cold years. Moreover, the 20th century rapid warming was not obvious in the NWSP mean maximum temperature reconstruction, which implied that mean maximum temperature might play an important and different role in global change as unique temperature indicators. Multi-taper method (MTM) spectral analysis revealed significant periodicities of 170-, 49-114-, 25-32-, 5.7-, 4.6-4.7-, 3.0-3.1-, 2.5-, and 2.1-2.3-year quasi-cycles at a 95 % confidence level in our reconstruction. Overall, the mean maximum temperature variability in the NWSP may be associated with global land-sea atmospheric circulation (e.g., ENSO, PDO, or AMO) as well as solar and volcanic forcing.
Ferrari, Ulisse
2016-08-01
Maximum entropy models provide the least constrained probability distributions that reproduce statistical properties of experimental datasets. In this work we characterize the learning dynamics that maximizes the log-likelihood in the case of large but finite datasets. We first show how the steepest descent dynamics is not optimal as it is slowed down by the inhomogeneous curvature of the model parameters' space. We then provide a way for rectifying this space which relies only on dataset properties and does not require large computational efforts. We conclude by solving the long-time limit of the parameters' dynamics including the randomness generated by the systematic use of Gibbs sampling. In this stochastic framework, rather than converging to a fixed point, the dynamics reaches a stationary distribution, which for the rectified dynamics reproduces the posterior distribution of the parameters. We sum up all these insights in a "rectified" data-driven algorithm that is fast and by sampling from the parameters' posterior avoids both under- and overfitting along all the directions of the parameters' space. Through the learning of pairwise Ising models from the recording of a large population of retina neurons, we show how our algorithm outperforms the steepest descent method.
Rząsa, Dariusz; Duda, Piotr
2011-12-01
Secure and cost-effective power generation has become very important nowdays. Care must be taken while designing and operating modern steam power plants. There are regulations such as German boiler regulations (Technische Regeln für Dampfkessel 301) or European Standards that guide the user how to operate the steam power plants. However, those regulations are based on the quasi-steady state assumption and one dimensional temperature distribution in the entire element. This simplifications may not guarantee that the heating and cooling operations are conducted in the most efficient way. Thus, it was important to find an improved method that can allow to establish optimum parameters for heating and cooling operations. The optimum parameters should guarantee that the maximum total stresses in the construction element are in the allowable limits and the entire process is conducted in the shortest time. This paper summarizes mathematical descriptions how to optimize shut down process of power block devices. The optimization formulation is based on the assumption that the maximum total stresses in the whole construction element should be kept within allowable limits during cooling operation. Additionally, the operation should be processed in the shortest time possible.
Temperature Sensing Above 1000 C Using Cr-Doped GdAlO3 Spin-Allowed Broadband Luminescence
Eldridge, Jeffrey I.; Chambers, Matthew D.
2012-01-01
Cr-doped GdAlO3 (Cr:GdAlO3) is shown to produce remarkably high-intensity spin-allowed broadband luminescence with sufficiently long decay times to make effective luminescence-decay-time based temperature measurements above 1000 C. This phosphor is therefore an attractive alternative to the much lower luminescence intensity rare-earth-doped thermographic phosphors that are typically utilized at these elevated temperatures. In particular, Cr:GdAlO3 will be preferred over rare-earth-doped phosphors, such as Dy:YAG, at temperatures up to 1200 C for intensity-starved situations when the much lower emission intensity from rare-earth-doped phosphors is insufficient for accurate temperature measurements in the presence of significant radiation background. While transition-metal-doped phosphors such as Cr:Al2O3 (ruby) are known to exhibit high luminescence intensity at low dopant concentrations, quenching due to nonradiative decay pathways competing with the (sup 2)E to (sup 4)A(sub 2) radiative transition (R line) has typically restricted their use for temperature sensing to below 600 C. Thermal quenching of the broadband (sup 4)T(sub 2) to (sup 4)A(sub 2) radiative transition from Cr:GdAlO3, however, is delayed until much higher temperatures (above 1000 C). This spin-allowed broadband emission persists to high temperatures because the lower-lying (sup 2)E energy level acts as a reservoir to thermally populate the higher shorter-lived (sup 4)T(sub 2) energy level and because the activation energy for nonradiative crossover relaxation from the (sup 4)T(sub 2) level to the (sup 4)A(sub 2) ground state is high. The strong crystal field associated with the tight bonding of the AlO6 octahedra in the GdAlO3 perovskite structure is responsible for this behavior.
Zhang, Yafei; Zhang, Fangqing; Chen, Guanghua
1994-12-01
It is proposed in this paper that the minimum substrate temperature for diamond growth from hydrogen-hydrocarbon gas mixtures be determined by the packing arrangements of hydrocarbon fragments at the surface, and the maximum substrate temperature be limited by the diamond growth surface reconstruction, which can be prevented by saturating the surface dangling bonds with atomic hydrogen. Theoretical calculations have been done by a formula proposed by Dryburgh [J. Crystal Growth 130 (1993) 305], and the results show that diamond can be deposited at the substrate temperatures ranging from ≈ 400 to ≈ 1200°C by low pressure chemical vapor deposition. This is consistent with experimental observations.
J C Joshi; Tankeshwar Kumar; Sunita Srivastava; Divya Sachdeva
2017-02-01
Maximum and minimum temperatures are used in avalanche forecasting models for snow avalanche hazard mitigation over Himalaya. The present work is a part of development of Hidden Markov Model (HMM) based avalanche forecasting system for Pir-Panjal and Great Himalayan mountain ranges of the Himalaya. In this work, HMMs have been developed for forecasting of maximum and minimum temperatures for Kanzalwan in Pir-Panjal range and Drass in Great Himalayan range with a lead time of two days. The HMMs have been developed using meteorological variables collected from these stations during the past 20 winters from 1992 to 2012. The meteorological variables have been used to define observations and states of the models and to compute model parameters (initial state, state transition and observation probabilities). The model parameters have been used in the Forward and the Viterbi algorithms to generate temperature forecasts. To improve the model forecasts, the model parameters have been optimised using Baum–Welch algorithm. The models have been compared with persistence forecast by root mean square errors (RMSE) analysis using independent data of two winters (2012–13, 2013–14). The HMM for maximum temperature has shown a 4–12% and 17–19% improvement in the forecast over persistence forecast, for day-1 and day-2, respectively. For minimum temperature, it has shown 6–38% and 5–12% improvement for day-1 and day-2, respectively.
Man, E. A.; Sera, D.; Mathe, L.
2016-01-01
systems are mostly tested under steady-state conditions for different constant input temperatures. However, for most TEG applications, the input temperature gradient changes, exposing the MPPT to variable tracking conditions. An example is the exhaust pipe on hybrid vehicles, for which, because...
Jackson, Faye L; Fryer, Robert J; Hannah, David M; Millar, Colin P; Malcolm, Iain A
2017-09-14
The thermal suitability of riverine habitats for cold water adapted species may be reduced under climate change. Riparian tree planting is a practical climate change mitigation measure, but it is often unclear where to focus effort for maximum benefit. Recent developments in data collection, monitoring and statistical methods have facilitated the development of increasingly sophisticated river temperature models capable of predicting spatial variability at large scales appropriate to management. In parallel, improvements in temporal river temperature models have increased the accuracy of temperature predictions at individual sites. This study developed a novel large scale spatio-temporal model of maximum daily river temperature (Twmax) for Scotland that predicts variability in both river temperature and climate sensitivity. Twmax was modelled as a linear function of maximum daily air temperature (Tamax), with the slope and intercept allowed to vary as a smooth function of day of the year (DoY) and further modified by landscape covariates including elevation, channel orientation and riparian woodland. Spatial correlation in Twmax was modelled at two scales; (1) river network (2) regional. Temporal correlation was addressed through an autoregressive (AR1) error structure for observations within sites. Additional site level variability was modelled with random effects. The resulting model was used to map (1) spatial variability in predicted Twmax under current (but extreme) climate conditions (2) the sensitivity of rivers to climate variability and (3) the effects of riparian tree planting. These visualisations provide innovative tools for informing fisheries and land-use management under current and future climate. Crown Copyright © 2017. Published by Elsevier B.V. All rights reserved.
Climate Prediction Center (CPC) U.S. Daily Maximum Air Temperature Observations
National Oceanic and Atmospheric Administration, Department of Commerce — Observational reports of daily air temperature (1200 UTC to 1200 UTC) are made by members of the NWS Automated Surface Observing Systems (ASOS) network; NWS...
Shao, Y. F.; Song, F.; Jiang, C. P.; Xu, X. H.; Wei, J. C.; Zhou, Z. L.
2016-02-01
We study the difference in the maximum stress on a cylinder surface σmax using the measured surface heat transfer coefficient hm instead of its average value ha during quenching. In the quenching temperatures of 200, 300, 400, 500, 600 and 800°C, the maximum surface stress σmmax calculated by hm is always smaller than σamax calculated by ha, except in the case of 800°C; while the time to reach σmax calculated by hm (fmmax) is always earlier than that by ha (famax). It is inconsistent with the traditional view that σmax increases with increasing Biot number and the time to reach σmax decreases with increasing Biot number. Other temperature-dependent properties also have a small effect on the trend of their mutual ratios with quenching temperatures. Such a difference between the two maximum surface stresses is caused by the dramatic variation of hm with temperature, which needs to be considered in engineering analysis.
Maximum Efficiency of Thermoelectric Heat Conversion in High-Temperature Power Devices
V. I. Khvesyuk
2016-01-01
Full Text Available Modern trends in development of aircraft engineering go with development of vehicles of the fifth generation. The features of aircrafts of the fifth generation are motivation to use new high-performance systems of onboard power supply. The operating temperature of the outer walls of engines is of 800–1000 K. This corresponds to radiation heat flux of 10 kW/m2 . The thermal energy including radiation of the engine wall may potentially be converted into electricity. The main objective of this paper is to analyze if it is possible to use a high efficiency thermoelectric conversion of heat into electricity. The paper considers issues such as working processes, choice of materials, and optimization of thermoelectric conversion. It presents the analysis results of operating conditions of thermoelectric generator (TEG used in advanced hightemperature power devices. A high-temperature heat source is a favorable factor for the thermoelectric conversion of heat. It is shown that for existing thermoelectric materials a theoretical conversion efficiency can reach the level of 15–20% at temperatures up to 1500 K and available values of Ioffe parameter being ZT = 2–3 (Z is figure of merit, T is temperature. To ensure temperature regime and high efficiency thermoelectric conversion simultaneously it is necessary to have a certain match between TEG power, temperature of hot and cold surfaces, and heat transfer coefficient of the cooling system. The paper discusses a concept of radiation absorber on the TEG hot surface. The analysis has demonstrated a number of potentialities for highly efficient conversion through using the TEG in high-temperature power devices. This work has been implemented under support of the Ministry of Education and Science of the Russian Federation; project No. 1145 (the programme “Organization of Research Engineering Activities”.
Temperature affects maximum H-reflex amplitude but not homosynaptic postactivation depression.
Racinais, Sébastien; Cresswell, Andrew G
2013-07-01
This study aimed to determinate the effect of hyperthermia on transmission efficacy of the Ia-afferent spinal pathway. Recruitment curves of the Hoffman reflex (H-reflex) and compound motor potential (M-wave) along with homosynaptic postactivation depression (HPAD) recovery curves were obtained in 14 volunteers in two controlled ambient temperatures that resulted in significantly different core temperatures (CON, core temperature ∼37.3°C; and HOT, core temperature ∼39.0°C). Electromyographic responses were obtained from the soleus (SOL) and medial gastrocnemius (MG) muscles following electrical stimulation of the tibial nerve at varying intensities and paired pulse frequencies (0.07-10 Hz). Results showed that maximal amplitude of the H-reflex was reached for a similar intensity of stimulation in CON and HOT (both muscles P > 0.47), with a similar associated M-wave (both muscles P > 0.69) but was significantly decreased in HOT as compared to CON (all P wave (-23% in SOL, -32% in MG). The HPAD recovery curve was not affected by the elevated core temperature (both muscles P > 0.23). Taken together, these results suggest that hyperthermia can alter neuromuscular transmission across the neuromuscular junction and/or muscle membrane as well as transmission efficacy of the Ia-afferent pathway, albeit the latter not via an increase in HPAD.
Backus, George A.; Lowry, Thomas Stephen; Jones, Shannon M; Walker, La Tonya Nicole; Roberts, Barry L; Malczynski, Leonard A.
2017-06-01
This report uses the CMIP5 series of climate model simulations to produce country- level uncertainty distributions for use in socioeconomic risk assessments of climate change impacts. It provides appropriate probability distributions, by month, for 169 countries and autonomous-areas on temperature, precipitation, maximum temperature, maximum wind speed, humidity, runoff, soil moisture and evaporation for the historical period (1976-2005), and for decadal time periods to 2100. It also provides historical and future distributions for the Arctic region on ice concentration, ice thickness, age of ice, and ice ridging in 15-degree longitude arc segments from the Arctic Circle to 80 degrees latitude, plus two polar semicircular regions from 80 to 90 degrees latitude. The uncertainty is meant to describe the lack of knowledge rather than imprecision in the physical simulation because the emphasis is on unfalsified risk and its use to determine potential socioeconomic impacts. The full report is contained in 27 volumes.
Sichilalu, S
2017-08-01
Full Text Available fission of methanogenic bacteria. The temperature was varied over time over several days and the biogas production is recorded every after 24 hours(1 day) . Based on the experiment setup, the results show a higher biogas production proportional to the rise...
Konstandinos G. Raptis
2012-01-01
Full Text Available Purpose of this study is the consideration of loading and contact problems encountered at rotating machine elements and especially at toothed gears. The later are some of the most commonly used mechanical components for rotary motion and power transmission. This fact proves the necessity for improved reliability and enhanced service life, which require precise and clear knowledge of the stress field at gear tooth. This study investigates the maximum allowable stresses occurring during spur gear tooth meshing computed using Niemannâs formulas at Highest Point of Single Tooth Contact (HPSTC. Gear material, module, power rating and number of teeth are considered as variable parameters. Furthermore, the maximum allowable stresses for maximum power transmission conditions are considered keeping the other parameters constant. After the application of Niemannâs formulas to both loading cases, the derived results are compared to the respective estimations of Finite Element Method (FEM using ANSYS software. Comparison of the results derived from Niemannâs formulas and FEM show that deviations between the two methods are kept at low level for both loading cases independently of the applied power (either random or maximum and the respective tangential load.
Claireaux, Guy; Couturier, Christine; Groison, Anne-Laure
2006-09-01
This study is an attempt to gain an integrated understanding of the interactions between temperature, locomotion activity and metabolism in the European sea bass (Dicentrarchus labrax). To our knowledge this study is among the few that have investigated the influence of the seasonal changes in water temperature on swimming performance in fish. Using a Brett-type swim-tunnel respirometer the relationship between oxygen consumption and swimming speed was determined in fish acclimatised to 7, 11, 14, 18, 22, 26 and 30 degrees C. The corresponding maximum swimming speed (U(max)), optimal swimming speed (U(opt)), active (AMR) and standard (SMR) metabolic rates as well as aerobic metabolic scope (MS) were calculated. Using simple mathematical functions, these parameters were modelled as a function of water temperature and swimming speed. Both SMR and AMR were positively related to water temperature up to 24 degrees C. Above 24 degrees C SMR and AMR levelled off and MS tended to decrease. We found a tight relationship between AMR and U(max) and observed that raising the temperature increased AMR and increased swimming ability. However, although fish swam faster at high temperature, the net cost of transport (COT(net)) at a given speed was not influence by the elevation of the water temperature. Although U(opt) doubled between 7 degrees C and 30 degrees C (from 0.3 to 0.6 m s(-1)), metabolic rate at U(opt) represented a relatively constant fraction of the animal active metabolic rate (40-45%). A proposed model integrates the effects of water temperature on the interaction between metabolism and swimming performance. In particular the controlling effect of temperature on AMR is shown to be the key factor limiting maximal swimming speed of sea bass.
Kraehenmann, Stefan; Kothe, Steffen; Ahrens, Bodo [Frankfurt Univ. (Germany). Inst. for Atmospheric and Environmental Sciences; Panitz, Hans-Juergen [Karlsruhe Institute of Technology (KIT), Eggenstein-Leopoldshafen (Germany)
2013-10-15
The representation of the diurnal 2-m temperature cycle is challenging because of the many processes involved, particularly land-atmosphere interactions. This study examines the ability of the regional climate model COSMO-CLM (version 4.8) to capture the statistics of daily maximum and minimum 2-m temperatures (Tmin/Tmax) over Africa. The simulations are carried out at two different horizontal grid-spacings (0.22 and 0.44 ), and are driven by ECMWF ERA-Interim reanalyses as near-perfect lateral boundary conditions. As evaluation reference, a high-resolution gridded dataset of daily maximum and minimum temperatures (Tmin/Tmax) for Africa (covering the period 2008-2010) is created using the regression-kriging-regression-kriging (RKRK) algorithm. RKRK applies, among other predictors, the remotely sensed predictors land surface temperature and cloud cover to compensate for the missing information about the temperature pattern due to the low station density over Africa. This dataset allows the evaluation of temperature characteristics like the frequencies of Tmin/Tmax, the diurnal temperature range, and the 90{sup th} percentile of Tmax. Although the large-scale patterns of temperature are reproduced well, COSMO-CLM shows significant under- and overestimation of temperature at regional scales. The hemispheric summers are generally too warm and the day-to-day temperature variability is overestimated over northern and southern extra-tropical Africa. The average diurnal temperature range is underestimated by about 2 C across arid areas, yet overestimated by around 2 C over the African tropics. An evaluation based on frequency distributions shows good model performance for simulated Tmin (the simulated frequency distributions capture more than 80% of the observed ones), but less well performance for Tmax (capture below 70%). Further, over wide parts of Africa a too large fraction of daily Tmax values exceeds the observed 90{sup th} percentile of Tmax, particularly across
Vladimir Kendrovski
2012-02-01
Full Text Available BACKGROUND. The goal of the present paper was to assess the impact of current and future burden of the ambient temperature to pollen distributions in Skopje. METHODS. In the study we have evaluated a correlation between the concentration of pollen grains in the atmosphere of Skopje and maximum temperature, during the vegetation period of 1996, 2003, 2007 and 2009 as a current burden in context of climate change. For our analysis we have selected 9 representative of each phytoallergen group (trees, grasses, weeds. The concentration of pollen grains has been monitored by a Lanzoni volumetric pollen trap. The correlation between the concentration of pollen grains in the atmosphere and selected meteorological variable from weekly monitoring has been studied with the help of linear regression and correlation coefficients. RESULTS. The prevalence of the sensibilization of standard pollen allergens in Skopje during the some period shows increasing from 16,9% in 1996 to 19,8% in 2009. We detect differences in onset of flowering, maximum and end of the length of seasons for pollen. The pollen distributions and risk increases in 3 main periods: early spring, spring and summer which are the main cause of allergies during these seasons. The largest increase of air temperature due to climate change in Skopje is expected in the summer season. CONCLUSION. The impacts of climate change by increasing of the temperature in the next decades very likely will include impacts on pollen production and differences in current pollen season. [TAF Prev Med Bull 2012; 11(1.000: 35-40
Sunawar, A.; Garniwa, I.
2017-03-01
Cars using the principle of converting heat energy into mechanical energy, but a lot of wasted heat energy not entirely transformed into mechanical energy, studies have been conducted that converts the heat energy into electrical energy using the principle thermoelectrically. However, there are many other energies that can be harnessed from the car, such as when the car is parked in the sun or driving in the heat of the sun, the temperature in the cabin can reach 80 degrees Celsius. The heat can be harmful to humans and the children immediately into the vehicle, as well as for the goods stored in the cabin if it contains toxins can evaporate because of the heat and dangerous. The danger can be prevented by reducing the heat in the cabin and transform into other forms of energy such as electricity. By providing a temperature difference of 40 degrees on the cold side of the module can be acquired electricity thermoelectrically up to 0.17W for one of its module, if it is made a module block the energy produced is enough to lower the temperature and charge batteries for further cooling. This study will use experiment method to get the maximum drop in temperature in the car cabin
Tremblay, Marissa; Spagnolo, Matteo; Ribolini, Adriano; Shuster, David
2016-04-01
The Gesso Valley, located in the southwestern-most, Maritime portion of the European Alps, contains an exceptionally well-preserved record of glacial advances during the late Pleistocene and Holocene. Detailed geomorphic mapping, geochronology of glacial deposits, and glacier reconstructions indicate that glaciers in this Mediterranean region responded to millennial scale climate variability differently than glaciers in the interior of the European Alps. This suggests that the Mediterranean Sea somehow modulated the climate of this region. However, since glaciers respond to changes in temperature and precipitation, both variables were potentially influenced by proximity to the Sea. To disentangle the competing effects of temperature and precipitation changes on glacier size, we are constraining past temperature variations in the Gesso Valley since the Last Glacial Maximum (LGM) using cosmogenic noble gas paleothermometry. The cosmogenic noble gases 3He and 21Ne experience diffusive loss from common minerals like quartz and feldspars at Earth surface temperatures. Cosmogenic noble gas paleothermometry utilizes this open-system behavior to quantitatively constrain thermal histories of rocks during exposure to cosmic ray particles at the Earth's surface. We will present measurements of cosmogenic 3He in quartz sampled from moraines in the Gesso Valley with LGM, Bühl stadial, and Younger Dryas ages. With these 3He measurements and experimental data quantifying the diffusion kinetics of 3He in quartz, we will provide a preliminary temperature reconstruction for the Gesso Valley since the LGM. Future work on samples from younger moraines in the valley system will be used to fill in details of the more recent temperature history.
Benz, Verena; Esper, Oliver; Gersonde, Rainer; Lamy, Frank; Tiedemann, Ralf
2016-08-01
Sea surface temperatures and sea-ice extent are most critical variables to evaluate the Southern Ocean paleoceanographic evolution in relation to the development of the global carbon cycle, atmospheric CO2 and ocean-atmosphere circulation. Here we present diatom transfer function-based summer sea surface temperature (SSST) and winter sea-ice (WSI) estimates from the Pacific sector of the Southern Ocean to bridge a gap in information that has to date hampered a well-established reconstruction of the last glacial Southern Ocean at circum-Antarctic scale. We studied the Last Glacial Maximum (LGM) at the EPILOG time slice (19,000-23,000 calendar years before present) in 17 cores and consolidated our LGM picture of the Pacific sector taking into account published data from its warmer regions. Our data display a distinct east-west differentiation with a rather stable WSI edge north of the Pacific-Antarctic Ridge in the Ross Sea sector and a more variable WSI extent over the Amundsen Abyssal Plain. The zone of maximum cooling (>4 K) during the LGM is in the present Subantarctic Zone and bounded to its south by the 4 °C isotherm. The isotherm is in the SSST range prevailing at the modern Antarctic Polar Front, representing a circum-Antarctic feature, and marks the northern edge of the glacial Antarctic Circumpolar Current (ACC). The northward deflection of colder than modern surface waters along the South American continent led to a significant cooling of the glacial Humboldt Current surface waters (4-8 K), which affected the temperature regimes as far north as tropical latitudes. The glacial reduction of ACC temperatures may also have resulted in significant cooling in the Atlantic and Indian Southern Ocean, thus enhancing thermal differentiation of the Southern Ocean and Antarctic continental cooling. The comparison with numerical temperature and sea-ice simulations yields discrepancies, especially concerning the estimates of the sea-ice fields, but some simulations
Hu, Junguo; Zhou, Jian; Zhou, Guomo; Luo, Yiqi; Xu, Xiaojun; Li, Pingheng; Liang, Junyi
2016-01-01
Soil respiration inherently shows strong spatial variability. It is difficult to obtain an accurate characterization of soil respiration with an insufficient number of monitoring points. However, it is expensive and cumbersome to deploy many sensors. To solve this problem, we proposed employing the Bayesian Maximum Entropy (BME) algorithm, using soil temperature as auxiliary information, to study the spatial distribution of soil respiration. The BME algorithm used the soft data (auxiliary information) effectively to improve the estimation accuracy of the spatiotemporal distribution of soil respiration. Based on the functional relationship between soil temperature and soil respiration, the BME algorithm satisfactorily integrated soil temperature data into said spatial distribution. As a means of comparison, we also applied the Ordinary Kriging (OK) and Co-Kriging (Co-OK) methods. The results indicated that the root mean squared errors (RMSEs) and absolute values of bias for both Day 1 and Day 2 were the lowest for the BME method, thus demonstrating its higher estimation accuracy. Further, we compared the performance of the BME algorithm coupled with auxiliary information, namely soil temperature data, and the OK method without auxiliary information in the same study area for 9, 21, and 37 sampled points. The results showed that the RMSEs for the BME algorithm (0.972 and 1.193) were less than those for the OK method (1.146 and 1.539) when the number of sampled points was 9 and 37, respectively. This indicates that the former method using auxiliary information could reduce the required number of sampling points for studying spatial distribution of soil respiration. Thus, the BME algorithm, coupled with soil temperature data, can not only improve the accuracy of soil respiration spatial interpolation but can also reduce the number of sampling points.
S. Gannouni
2016-01-01
Full Text Available In a tunnel fire, the production of smoke and toxic gases remains the principal prejudicial factors to users. The heat is not considered as a major direct danger to users since temperatures up to man level do not reach tenable situations that after a relatively long time except near the fire source. However, the temperatures under ceiling can exceed the thresholds conditions and can thus cause structural collapse of infrastructure. This paper presents a numerical analysis of smoke hazard in tunnel fires with different aspect ratio by large eddy simulation. Results show that the CO concentration increases as the aspect ratio decreases and decreases with the longitudinal ventilation velocity. CFD predicted maximum smoke temperatures are compared to the calculated values using the model of Li et al. and then compared with those given by the empirical equation proposed by kurioka et al. A reasonable good agreement has been obtained. The backlayering length decreases as the ventilation velocity increases and this decrease fell into good exponential decay. The dimensionless interface height and the region of bad visibility increases with the aspect ratio of the tunnel cross-sectional geometry.
Maximum energy product at elevated temperatures for hexagonal strontium ferrite (SrFe12O19) magnet
Park, J; Hong, YK; Kim, SG; Kim, S; Liyanage, LSI; Lee, J; Lee, W; Abo, GS; Hur, KH; An, SY
2014-04-01
The electronic structure of hexagonal strontium ferrite (SrFe12O19) was calculated based on the density functional theory (DFT) and generalized gradient approximation (GGA). The GGA+U method was used to improve the description of localized Fe 3d electrons. Three different effective U (U-eff) values of 3.7, 7.0, and 10.3 eV were used to calculate three sets of exchange integrals for 21 excited states. We then calculated the temperature dependence of magnetic moments m(T) for the five sublattices (2a, 2b, 12k, 4f(1), and 4f(2)) using the exchange integrals. The m(T) of the five sublattices are inter related to the nearest neighbors, where the spins are mostly anti-ferromagnetically coupled. The five sublattice m(T) were used to ()brain the saturation magnetization M-s(T) of SrFe12O19, which is in good agreement with the experimental values. The temperature dependence of maximum energy product. ((BII)(max)(T)) was calculated using the calculated M-s(T). (C) 2013 Elsevier B.V. All rights reserved.
Heuzé, Céline; Eriksson, Leif; Carvajal, Gisela
2017-04-01
Using sea surface temperature from satellite images to retrieve sea surface currents is not a new idea, but so far its operational near-real time implementation has not been possible. Validation studies are too region-specific or uncertain, due to the errors induced by the images themselves. Moreover, the sensitivity of the most common retrieval method, the maximum cross correlation, to the three parameters that have to be set is unknown. Using model outputs instead of satellite images, biases induced by this method are assessed here, for four different seas of Western Europe, and the best of nine settings and eight temporal resolutions are determined. For all regions, tracking a small 5 km pattern from the first image over a large 30 km region around its original location on a second image, separated from the first image by 6 to 9 hours returned the most accurate results. Moreover, for all regions, the problem is not inaccurate results but missing results, where the velocity is too low to be picked by the retrieval. The results are consistent both with limitations caused by ocean surface current dynamics and with the available satellite technology, indicating that automated sea surface current retrieval from sea surface temperature images is feasible now, for search and rescue operations, pollution confinement or even for more energy efficient and comfortable ship navigation.
U.S. Geological Survey, Department of the Interior — This data set represents the 30-year (1971-2000) average annual maximum temperature in Celsius multiplied by 100 compiled for every catchment of NHDPlus for the...
Xiaokang Kou
2016-01-01
Full Text Available Land surface temperature (LST plays a major role in the study of surface energy balances. Remote sensing techniques provide ways to monitor LST at large scales. However, due to atmospheric influences, significant missing data exist in LST products retrieved from satellite thermal infrared (TIR remotely sensed data. Although passive microwaves (PMWs are able to overcome these atmospheric influences while estimating LST, the data are constrained by low spatial resolution. In this study, to obtain complete and high-quality LST data, the Bayesian Maximum Entropy (BME method was introduced to merge 0.01° and 0.25° LSTs inversed from MODIS and AMSR-E data, respectively. The result showed that the missing LSTs in cloudy pixels were filled completely, and the availability of merged LSTs reaches 100%. Because the depths of LST and soil temperature measurements are different, before validating the merged LST, the station measurements were calibrated with an empirical equation between MODIS LST and 0~5 cm soil temperatures. The results showed that the accuracy of merged LSTs increased with the increasing quantity of utilized data, and as the availability of utilized data increased from 25.2% to 91.4%, the RMSEs of the merged data decreased from 4.53 °C to 2.31 °C. In addition, compared with the filling gap method in which MODIS LST gaps were filled with AMSR-E LST directly, the merged LSTs from the BME method showed better spatial continuity. The different penetration depths of TIR and PMWs may influence fusion performance and still require further studies.
Gabarro, Carolina; Turiel, Antonio; Elosegui, Pedro; Pla-Resina, Joaquim A.; Portabella, Marcos
2017-08-01
Monitoring sea ice concentration is required for operational and climate studies in the Arctic Sea. Technologies used so far for estimating sea ice concentration have some limitations, for instance the impact of the atmosphere, the physical temperature of ice, and the presence of snow and melting. In the last years, L-band radiometry has been successfully used to study some properties of sea ice, remarkably sea ice thickness. However, the potential of satellite L-band observations for obtaining sea ice concentration had not yet been explored. In this paper, we present preliminary evidence showing that data from the Soil Moisture Ocean Salinity (SMOS) mission can be used to estimate sea ice concentration. Our method, based on a maximum-likelihood estimator (MLE), exploits the marked difference in the radiative properties of sea ice and seawater. In addition, the brightness temperatures of 100 % sea ice and 100 % seawater, as well as their combined values (polarization and angular difference), have been shown to be very stable during winter and spring, so they are robust to variations in physical temperature and other geophysical parameters. Therefore, we can use just two sets of tie points, one for summer and another for winter, for calculating sea ice concentration, leading to a more robust estimate. After analysing the full year 2014 in the entire Arctic, we have found that the sea ice concentration obtained with our method is well determined as compared to the Ocean and Sea Ice Satellite Application Facility (OSI SAF) dataset. However, when thin sea ice is present (ice thickness ≲ 0.6 m), the method underestimates the actual sea ice concentration. Our results open the way for a systematic exploitation of SMOS data for monitoring sea ice concentration, at least for specific seasons. Additionally, SMOS data can be synergistically combined with data from other sensors to monitor pan-Arctic sea ice conditions.
Kinkhabwala, Ali
2013-01-01
The most fundamental problem in statistics is the inference of an unknown probability distribution from a finite number of samples. For a specific observed data set, answers to the following questions would be desirable: (1) Estimation: Which candidate distribution provides the best fit to the observed data?, (2) Goodness-of-fit: How concordant is this distribution with the observed data?, and (3) Uncertainty: How concordant are other candidate distributions with the observed data? A simple unified approach for univariate data that addresses these traditionally distinct statistical notions is presented called "maximum fidelity". Maximum fidelity is a strict frequentist approach that is fundamentally based on model concordance with the observed data. The fidelity statistic is a general information measure based on the coordinate-independent cumulative distribution and critical yet previously neglected symmetry considerations. An approximation for the null distribution of the fidelity allows its direct conversi...
胡吉磊; 徐建国; 姚耀明; 宋刚; 吴欣
2011-01-01
铝包钢绞线张力大、弧垂小,在输电线路大跨越设计中具有很好的应用前景,但是因为输送容量偏小,限制了其使用范围.通过试验验证,将铝包钢绞线的最高允许运行温度提高至130 0C,从而极大地增加了其输送能力,为今后大跨越线路设计提供了新的思路.
Kawakita, Hideyo; Arai, Akira; Fujii, Mitsugu
2016-10-01
The molecular formation of C2 and CN in the dust-forming classical nova V2676 Oph occurs during its near-maximum phase. We investigated the temporal evolution of the photospheric temperature of the nova as it approached molecular formation during its early phase. The effective temperature of the nova around the maximum decreased from ˜7000 K to ˜5000 K over the course of ˜3 d. The molecules formed at temperatures of conditions favorable to the molecular formation of C2 and CN in V2676 Oph.
Davis, Katherine M; Mattern, Brian A; Pacold, Joseph I; Zakharova, Taisiya; Brewe, Dale; Kosheleva, Irina; Henning, Robert W; Graber, Timothy J; Heald, Steve M; Seidler, Gerald T; Pushkar, Yulia
2012-07-19
The paradigm of "detection-before-destruction" was tested for a metalloprotein complex exposed at room temperature to the high x-ray flux typical of third generation synchrotron sources. Following the progression of the x-ray induced damage by Mn Kβ x-ray emission spectroscopy, we demonstrated the feasibility of collecting room temperature data on the electronic structure of native Photosystem II, a trans-membrane metalloprotein complex containing a Mn(4)Ca cluster. The determined non-damaging observation timeframe (about 100 milliseconds using continuous monochromatic beam, deposited dose 1*10(7) photons/µm(2) or 1.3*10(4) Gy, and 66 microseconds in pulsed mode using pink beam, deposited dose 4*10(7) photons/µm(2) or 4.2*10(4) Gy) is sufficient for the analysis of this protein's electron dynamics and catalytic mechanism at room temperature. Reported time frames are expected to be representative for other metalloproteins. The described instrumentation, based on the short working distance dispersive spectrometer, and experimental methodology is broadly applicable to time-resolved x-ray emission analysis at synchrotron and x-ray free-electron laser light sources.
Phan Thanh Noi
2016-12-01
Full Text Available This study aims to evaluate quantitatively the land surface temperature (LST derived from MODIS (Moderate Resolution Imaging Spectroradiometer MOD11A1 and MYD11A1 Collection 5 products for daily land air surface temperature (Ta estimation over a mountainous region in northern Vietnam. The main objective is to estimate maximum and minimum Ta (Ta-max and Ta-min using both TERRA and AQUA MODIS LST products (daytime and nighttime and auxiliary data, solving the discontinuity problem of ground measurements. There exist no studies about Vietnam that have integrated both TERRA and AQUA LST of daytime and nighttime for Ta estimation (using four MODIS LST datasets. In addition, to find out which variables are the most effective to describe the differences between LST and Ta, we have tested several popular methods, such as: the Pearson correlation coefficient, stepwise, Bayesian information criterion (BIC, adjusted R-squared and the principal component analysis (PCA of 14 variables (including: LST products (four variables, NDVI, elevation, latitude, longitude, day length in hours, Julian day and four variables of the view zenith angle, and then, we applied nine models for Ta-max estimation and nine models for Ta-min estimation. The results showed that the differences between MODIS LST and ground truth temperature derived from 15 climate stations are time and regional topography dependent. The best results for Ta-max and Ta-min estimation were achieved when we combined both LST daytime and nighttime of TERRA and AQUA and data from the topography analysis.
Abbasnia, Mohsen; Tavousi, Taghi; Khosravi, Mahmood
2016-08-01
Identification and assessment of climate change in the next decades with the aim of appropriate environmental planning in order to adapt and mitigate its effects are quite necessary. In this study, maximum temperature changes of Iran were comparatively examined in two future periods (2041-2070 and 2071-2099) and based on the two general circulation model outputs (CGCM3 and HADCM3) and under existing emission scenarios (A2, A1B, B1 and B2). For this purpose, after examining the ability of statistical downscaling method of SDSM in simulation of the observational period (1981-2010), the daily maximum temperature of future decades was downscaled by considering the uncertainty in seven synoptic stations as representatives of climate in Iran. In uncertainty analysis related to model-scenarios, it was found that CGCM3 model under scenario B1 had the best performance about the simulation of future maximum temperature among all of the examined scenario-models. The findings also showed that the maximum temperature at study stations will be increased between 1°C and 2°C in the middle and the end of 21st century. Also this maximum temperature changes is more severe in the HADCM3 model than the CGCM3 model.
Blandamer, MJ; Buurma, NJ; Engberts, JBFN; Reis, JCR; Buurma, Niklaas J.; Reis, João C.R.
2003-01-01
At temperatures above and below the temperature of maximum density, TMD, for water at ambient pressure, pairs of temperatures exist at which the molar volumes of water are equal. First-order rate constants for the pH-independent hydrolysis of 1-benzoyl-1,2,4-triazole in aqueous solution at pairs of
Human Resources Division
2001-01-01
HR Division wishes to clarify to members of the personnel that the allowance for a dependent child continues to be paid during all training courses ('stages'), apprenticeships, 'contrats de qualification', sandwich courses or other courses of similar nature. Any payment received for these training courses, including apprenticeships, is however deducted from the amount reimbursable as school fees. HR Division would also like to draw the attention of members of the personnel to the fact that any contract of employment will lead to the suppression of the child allowance and of the right to reimbursement of school fees.
Hertzberg, Jennifer E.; Schmidt, Matthew W.; Bianchi, Thomas S.; Smith, Richard W.; Shields, Michael R.; Marcantonio, Franco
2016-01-01
The use of the TEX86 temperature proxy has thus far come to differing results as to whether TEX86 temperatures are representative of surface or subsurface conditions. In addition, although TEX86 temperatures might reflect sea surface temperatures based on core-top (Holocene) values, this relationship might not hold further back in time. Here, we investigate the TEX86 temperature proxy by comparing TEX86 temperatures to Mg/Ca temperatures of multiple species of planktonic foraminifera for two sites in the eastern tropical Pacific (on the Cocos and Carnegie Ridges) across the Holocene and Last Glacial Maximum. Core-top and Holocene TEX86H temperatures at both study regions agree well, within error, with the Mg/Ca temperatures of Globigerinoides ruber, a surface dwelling planktonic foraminifera. However, during the Last Glacial Maximum, TEX86H temperatures are more representative of upper thermocline temperatures, and are offset from G. ruber Mg/Ca temperatures by 5.8 °C and 2.9 °C on the Cocos Ridge and Carnegie Ridge, respectively. This offset between proxies cannot be reconciled by using different TEX86 temperature calibrations, and instead, we suggest that the offset is due to a deeper export depth of GDGTs at the LGM. We also compare the degree of glacial cooling at both sites based on both temperature proxies, and find that TEX86H temperatures greatly overestimate glacial cooling, especially on the Cocos Ridge. This study has important implications for applying the TEX86 paleothermometer in the eastern tropical Pacific.
Serfontein, Dawid E., E-mail: Dawid.Serfontein@nwu.ac.za
2014-05-01
In a preceding study, coupled neutronics and thermo-hydraulic simulations were performed with the VSOP-A diffusion code for the standard 9.6 wt% enriched 9 g uranium fuel spheres in the 400 MWth Pebble Bed Modular Reactor Demonstration Power Plant. The axial power profile peaked at about a third from the top of the fuel core and the radial profile peaked directly adjacent to the central graphite reflector. The maximum temperature during a Depressurised Loss of Coolant (DLOFC) incident was 1581.0 °C, which is close to the limit of 1600 °C above which the leakage of radioactive fission products through the TRISO coatings around the fuel kernels may become unacceptable. This may present licensing challenges and also limits the total power output of the reactor. In this article the results of an optimisation study of the axial and radial power profiles for this reactor are reported. The main aim was to minimise the maximum DLOFC temperature. Reducing the maximum equilibrium temperature during normal operation was a lesser aim. Minimising the maximum DLOFC temperature was achieved by placing an optimised distribution of {sup 10}B neutron poison in the central reflector. The standard power profiles are sub-optimal with respect to the passive leakage of decay heat during a DLOFC. Since the radial power profile peaks directly adjacent to the central reflector, the distance that the decay heat needs to be conducted toward the outside of the reactor and the ultimate heat sink is at a maximum. The sharp axial power profile peak means that most of the decay power is concentrated in a small part of the core volume, thereby sharply increasing the required outward heat flux in this hotspot region. Both these features sharply increase the maximum DLOFC temperatures in this hotspot. Therefore the axial distribution of the neutron poisons in the central reflector was optimised so as to push the equilibrium power density profile radially outward and to suppress the axial power peak
Djeison Cesar Batista
2011-09-01
Full Text Available Thermal rectification of wood was developed in the decade of 1940 and has been largely studied and produced in Europe. In Brazil, the research about this technique is still little and sparse, but it has gained attention nowadays. The aim of this study was to evaluate the influence of time and temperature of rectification on the reduction of maximum swelling of Eucalyptus grandis wood. According to the results obtained it is possible to achieve reductions of about 50% on the maximum volumetric swelling of Eucalyptus grandis wood. Best results were obtained for 230°C of thermal rectification rather than 200°C. The factor temperature was more significant than time, once that there was no significant difference between the times used (1, 2 and 3 hours. There was no significant interaction between the factors time and temperature.
Mroczka, Janusz; Ostrowski, Mariusz
2015-06-01
Disadvantages of photovoltaic panels are their low efficiency and non-linear current-voltage characteristic. Therefore it is necessary to apply the maximum power tracking systems which are dependent on the sun exposure and temperature. Trackers, that are used in photovoltaic systems, differ from each other in the speed and accuracy of tracking. Typically, in order to determine the maximum power point, trackers use measure of current and voltage. The perturb and observe algorithm or the incremental conductance method are frequent in the literature. The drawback of these solutions is the need to search the entire current-voltage curve, resulting in a significant loss of power in the fast-changing lighting conditions. Modern solutions use an additional measurement of temperature, short-circuit current or open circuit voltage in order to determine the starting point of one of the above methods, what decreases the tracking time. For this paper, a sequence of simulations and tests in real shading and temperature conditions for the investigated method, which uses additional light sensor to increase the speed of the perturb and observe algorithm in fast-changing illumination conditions was performed. Due to the non-linearity of the light sensor and the photovoltaic panel and the influence of temperature on the used sensor and panel characteristics, we cannot directly determine the relationship between them. For this reason, the tested method is divided into two steps. In the first step algorithm uses the correlation curve of the light sensor and current at the maximum power point and determines the current starting point with respect of which the perturb and observe algorithm is run. When the maximum power point is reached, in a second step, the difference between the starting point and the actual maximum power point is calculated and on this basis the coefficients of correlation curve are modified.
2011-08-29
nonylphenol, All samples were melted, blended, and de- gassed for 30 min. prior to cure in silicone molds under N2, cure schedules as indicated “BADCy” “LECy...technique is limited by the difficulty in separating DSC signals due to cure and degradation at very high temperatures. 14 0 50 100 150 200 250 300 0.5...of superior predictive models; readily catalyzed to cure at reasonable temperatures, providing a wide and tunable processing window • Amenable to
Pigeon, Karine E; Cardinal, Etienne; Stenhouse, Gordon B; Côté, Steeve D
2016-08-01
To fulfill their needs, animals are constantly making trade-offs among limiting factors. Although there is growing evidence about the impact of ambient temperature on habitat selection in mammals, the role of environmental conditions and thermoregulation on apex predators is poorly understood. Our objective was to investigate the influence of ambient temperature on habitat selection patterns of grizzly bears in the managed landscape of Alberta, Canada. Grizzly bear habitat selection followed a daily and seasonal pattern that was influenced by ambient temperature, with adult males showing stronger responses than females to warm temperatures. Cutblocks aged 0-20 years provided an abundance of forage but were on average 6 °C warmer than mature conifer stands and 21- to 40-year-old cutblocks. When ambient temperatures increased, the relative change (odds ratio) in the probability of selection for 0- to 20-year-old cutblocks decreased during the hottest part of the day and increased during cooler periods, especially for males. Concurrently, the probability of selection for 21- to 40-year-old cutblocks increased on warmer days. Following plant phenology, the odds of selecting 0- to 20-year-old cutblocks also increased from early to late summer while the odds of selecting 21- to 40-year-old cutblocks decreased. Our results demonstrate that ambient temperatures, and therefore thermal requirements, play a significant role in habitat selection patterns and behaviour of grizzly bears. In a changing climate, large mammals may increasingly need to adjust spatial and temporal selection patterns in response to thermal constraints.
Philip D. Jones
2010-12-01
Full Text Available Global surface temperature trends, based on land and marine data, show warming of about 0.8 °C over the last 100 years. This rate of warming is sometimes questioned because of the existence of Urban Heat Islands (UHIs. In this study we compare the rate of temperature change estimated from measurements of land and marine temperatures for the same grid squares using 5° by 5° latitude/longitude grid-box datasets. For 1951–2009 the ‘land’ average warmed by 0.02 °C decade−1 relative to the ‘sea surface temperature’ (SST average. There were regional contrasts in the trends of land/sea temperature differences: the land warmed at a greater rate compared to the SST for regions north of 20°S, but the opposite occurred further south. Given strong forcing of the climate system, we would expect the land to change more rapidly than the ocean, so the differences represent an upper limit to the urbanization effect.
Goutam, Shovon; Timmermans, Jean-Marc; Omar, Noshin;
2014-01-01
, manganese and cobalt (NMC) based and the anode is graphite based. In order to measure the surface temperature, thermal infrared (IR) camera and contact thermocouples were used. A fairly uniform temperature distribution was observed over the cell surface in case of continuous charge and discharge up to 100A...
Mitsunaga, B.; Mering, J. A.; Eagle, R.; Bricker, H. L.; Davila, N.; Trewman, S.; Burford, S.; Li, G.; Tripati, A. K.
2016-12-01
The climate of the Chinese Loess Plateau is affected by the East Asian Monsoon, an important water source for over a billion people. We are examining how temperature and hydrology on the Loess Plateau has changed since the Last Glacial Maximum (18,000 - 23,000 years before the present) in response to insolation, deglaciation, and rising levels of greenhouse gases. Specifically, we are reconstructing temperature and meteoric δ18O through paired clumped and oxygen isotope analyses performed on carbonate minerals. Clumped isotope thermometry—the use of 13C—18O bond frequency in carbonates—is a novel geochemical proxy that provides constraints on mineral formation temperatures and can be combined with carbonate δ18O to quantify meteoric δ18O. We have measured a suite of nodular loess concretions and gastropod shells from the modern as well as the Last Glacial Maximum from 15 sites across the Chinese Loess Plateau. These observations constrain spatial variations in temperature and precipitation, which in turn will provide key constraints on models that simulate changes in regional climates and monsoon intensity over the last 20,000 years.
Crespo, Daniel; Grilo, Tiago Fernandes; Baptista, Joana; Coelho, João Pedro; Lillebø, Ana Isabel; Cássio, Fernanda; Fernandes, Isabel; Pascoal, Cláudia; Pardal, Miguel Ângelo; Dolbeth, Marina
2017-06-20
The Paris Agreement signed by 195 countries in 2015 sets out a global action plan to avoid dangerous climate change by limiting global warming to remain below 2 °C. Under that premise, in situ experiments were run to test the effects of 2 °C temperature increase on the benthic communities in a seagrass bed and adjacent bare sediment, from a temperate European estuary. Temperature was artificially increased in situ and diversity and ecosystem functioning components measured after 10 and 30 days. Despite some warmness effects on the analysed components, significant impacts were not verified on macro and microfauna structure, bioturbation or in the fluxes of nutrients. The effect of site/habitat seemed more important than the effects of the warmness, with the seagrass habitat providing more homogenous results and being less impacted by warmness than the adjacent bare sediment. The results reinforce that most ecological responses to global changes are context dependent and that ecosystem stability depends not only on biological diversity but also on the availability of different habitats and niches, highlighting the role of coastal wetlands. In the context of the Paris Agreement it seems that estuarine benthic ecosystems will be able to cope if global warming remains below 2 °C.
Felis, Thomas; McGregor, Helen V.; Linsley, Braddock K.; Tudhope, Alexander W.; Gagan, Michael K.; Suzuki, Atsushi; Inoue, Mayuri; Thomas, Alexander L.; Esat, Tezer M.; Thompson, William G.; Tiwari, Manish; Potts, Donald C.; Mudelsee, Manfred; Yokoyama, Yusuke; Webster, Jody M.
2015-04-01
Tropical south-western Pacific temperatures are of vital importance to the Great Barrier Reef (GBR), but the role of sea surface temperatures (SSTs) in the growth of the GBR since the Last Glacial Maximum remains largely unknown. Here we present records of Sr/Ca and δ18O for Last Glacial Maximum and deglacial corals that were drilled by Integrated Ocean Drilling Program (IODP) Expedition 325 along the shelf edge seaward of the modern GBR. The Sr/Ca and δ18O records of the precisely U-Th dated fossil shallow-water corals show a considerably steeper meridional SST gradient than the present day in the central GBR. We find a 1-2 ° C larger temperature decrease between 17° S and 20° S about 20,000 to 13,000 years ago. The result is best explained by the northward expansion of cooler subtropical waters due to a weakening of the South Pacific gyre and East Australian Current. Our findings indicate that the GBR experienced substantial and regionally differing temperature change during the last deglaciation, much larger temperature changes than previously recognized. Furthermore, our findings suggest a northward contraction of the Western Pacific Warm Pool during the LGM and last deglaciation, and serve to explain anomalous drying of northeastern Australia at that time. Overall, the GBR developed through significant SST change and, considering temperature alone, may be more resilient than previously thought. Webster, J. M., Yokoyama, Y. & Cotteril, C. & the Expedition 325 Scientists. Proceedings of the Integrated Ocean Drilling Program Vol. 325 (Integrated Ocean Drilling Program Management International Inc., 2011). Felis, T., McGregor, H. V., Linsley, B. K., Tudhope, A. W., Gagan, M. K., Suzuki, A., Inoue, M., Thomas, A. L., Esat, T. M., Thompson, W. G., Tiwari, M., Potts, D. C., Mudelsee, M., Yokoyama, Y., Webster, J. M. Intensification of the meridional temperature gradient in the Great Barrier Reef following the Last Glacial Maximum. Nature Communications 5, 4102
Werne, J. P.; Halbur, J.; Rubesch, M.; Brown, E. T.; Ortega, B.; Caballero, M.; Correa-Metrio, A.; Lozano, S.
2013-05-01
The water balance of the Southwestern United States and most of Mexico is dependent on regional climate systems, including the Mexican (or North American) Monsoon. The Mexican Monsoon leads to significant summer rainfall across a broad swath of the continent, which constitutes the major source of annual precipitation over much of this region. The position of the ITCZ and the strength of the accompanying monsoon are affected by variability in insolation. Stronger northern hemisphere summer insolation shifts the ITCZ northward, bringing about a more intense monsoon. Here we discuss a new geochemical climate record from Lake Chalco, Mexico, which couples inorganic (X-ray fluorescence) and organic (biomarkers and stable isotopes) geochemical proxies to reconstruct temperature and aridity over the past 45,000 years, as well as the response of terrestrial vegetation to such climate changes. The Basin of Mexico is a high altitude closed lacustrine basin (20°N, 99°W; 2240 m.a.s.l.) in the Trans Mexican Volcanic Belt. The plain of Lake Chalco, located near Mexico City in the southern sub-basin, has an area of 120 km2 and a catchment of 1100 km2. Though the present-day lake has been reduced to a small marsh due to historic diversion of its waters, over longer timescales the lake has been a sensitive recorder of hydroclimatic variations. Low Ca concentrations indicate more arid periods during the late glacial (34 - 15 kybp) compared to the last interstadial or early Holocene. This observation is supported by the ratio of terrestrial to aquatic lipid biomarkers (long vs. short chain n-alkanes), which indicate greater relative inputs of aquatic biomarkers during wetter periods. The changes in aridity as shown in these geochemical proxies are compared with temperature as reflected in glycerol dialkyl glycerol tetraether (GDGT) based paleotemperature proxies to assess the extent to which insolation may have driven aridity variations, and with terrestrial and aquatic biomarker
V R Durai; Rashmi Bhardwaj
2014-07-01
The output from Global Forecasting System (GFS) T574L64 operational at India Meteorological Department (IMD), New Delhi is used for obtaining location specific quantitative forecast of maximum and minimum temperatures over India in the medium range time scale. In this study, a statistical bias correction algorithm has been introduced to reduce the systematic bias in the 24–120 hour GFS model location specific forecast of maximum and minimum temperatures for 98 selected synoptic stations, representing different geographical regions of India. The statistical bias correction algorithm used for minimizing the bias of the next forecast is Decaying Weighted Mean (DWM), as it is suitable for small samples. The main objective of this study is to evaluate the skill of Direct Model Output (DMO) and Bias Corrected (BC) GFS for location specific forecast of maximum and minimum temperatures over India. The performance skill of 24–120 hour DMO and BC forecast of GFS model is evaluated for all the 98 synoptic stations during summer (May–August 2012) and winter (November 2012–February 2013) seasons using different statistical evaluation skill measures. The magnitude of Mean Absolute Error (MAE) and Root Mean Squared Error (RMSE) for BC GFS forecast is lower than DMO during both summer and winter seasons. The BC GFS forecasts have higher skill score as compared to GFS DMO over most of the stations in all day-1 to day-5 forecasts during both summer and winter seasons. It is concluded from the study that the skill of GFS statistical BC forecast improves over the GFS DMO remarkably and hence can be used as an operational weather forecasting system for location specific forecast over India.
Shepherd, M. G.
2014-12-01
Manifestations of thermospheric dynamics are observed in the variations of upper atmosphere neutral winds, temperature, density and F-region plasma over a wide time range. These fields are influenced by perturbations propagating vertically from the lower and middle atmosphere (e.g. tides) and from above through variations in the solar and geomagnetic activity. The midnight temperature maximum (MTM) is a large scale neutral temperature anomaly with wide spread influence on the low-latitude thermosphere and ionosphere. Variations in the low latitudes' nighttime neutral density, termed midnight density maximum (MDM) have also been observed and modeled. Although there is a large body of work on the characteristics of the MTM (& MDM) there are still a few questions which remain to be answered concerning the global scale distribution of the MTM (&MDM), their spatial extent and longitudinal variations, their global seasonal occurrence pattern and amplitude. The Wind Imaging Interferometer (WINDII) flown on the Upper Atmosphere Research Satellite (UARS) provides among other parameters multiyear observations of O(1D) nightglow volume emission rates (VER), Doppler temperatures, and neutral winds over the altitude range from 150 to 300 km with continuous latitude coverage from 42°N to 42°S and to 72° in one hemisphere every 36 days. These correlative in time and space data are employed in the study of the global and seasonal extent of the MTM/MDM. The results are compared with simulations by the Canadian Ionosphere and Atmosphere Model (C-IAM). Reasonable agreement is obtained in terms of temporal, solar flux, and solar zenith angle variations.
Huang, S.-Y.; Wang, J.
2016-07-01
A coupled force-restore model of surface soil temperature and moisture (FRMEP) is formulated by incorporating the maximum entropy production model of surface heat fluxes and including the gravitational drainage term. The FRMEP model driven by surface net radiation and precipitation are independent of near-surface atmospheric variables with reduced sensitivity to the uncertainties of model input and parameters compared to the classical force-restore models (FRM). The FRMEP model was evaluated using observations from two field experiments with contrasting soil moisture conditions. The modeling errors of the FRMEP predicted surface temperature and soil moisture are lower than those of the classical FRMs forced by observed or bulk formula based surface heat fluxes (bias 1 ~ 2°C versus ~4°C, 0.02 m3 m-3 versus 0.05 m3 m-3). The diurnal variations of surface temperature, soil moisture, and surface heat fluxes are well captured by the FRMEP model measured by the high correlations between the model predictions and observations (r ≥ 0.84). Our analysis suggests that the drainage term cannot be neglected under wet soil condition. A 1 year simulation indicates that the FRMEP model captures the seasonal variation of surface temperature and soil moisture with bias less than 2°C and 0.01 m3 m-3 and correlation coefficients of 0.93 and 0.9 with observations, respectively.
Barker, Stephen; Cacho, Isabel; Benway, Heather; Tachikawa, Kazuyo
2005-04-01
As part of the Multi-proxy Approach for the Reconstruction of the Glacial Ocean (MARGO) incentive, published and unpublished temperature reconstructions for the Last Glacial Maximum (LGM) based on planktonic foraminiferal Mg/Ca ratios have been synthesised and made available in an online database. Development and applications of Mg/Ca thermometry are described in order to illustrate the current state of the method. Various attempts to calibrate foraminiferal Mg/Ca ratios with temperature, including culture, trap and core-top approaches have given very consistent results although differences in methodological techniques can produce offsets between laboratories which need to be assessed and accounted for where possible. Dissolution of foraminiferal calcite at the sea-floor generally causes a lowering of Mg/Ca ratios. This effect requires further study in order to account and potentially correct for it if dissolution has occurred. Mg/Ca thermometry has advantages over other paleotemperature proxies including its use to investigate changes in the oxygen isotopic composition of seawater and the ability to reconstruct changes in the thermal structure of the water column by use of multiple species from different depth and or seasonal habitats. Presently available data are somewhat limited to low latitudes where they give fairly consistent values for the temperature difference between Late Holocene and the LGM (2-3.5 °C). Data from higher latitudes are more sparse, and suggest there may be complicating factors when comparing between multi-proxy reconstructions.
ASSESSMENT OF MAXIMUM ALLOWABLE FISCAL BURDEN ON UKRAINE NATIONAL ECONOMY
M. Aleksandrova
2014-03-01
Full Text Available The article was reviewed reproductive aspect of the relationship between fiscal burden and a penchant for economic development under certain assumptions about the relationship of these variables. The analysis was based on a fairly simple dynamic model in which the share of income that goes to the development of production, relying constant. Computed optimal fiscal burden for the economic development of the country is 19.29% of GDP. The estimation and comparison of the calculations of the tax burden followed its dynamics, by comparative assessment with those of developed countries. The prospects of the proposed approach for predicting the development of national economy were analyzed.
ZHANG De'er; Demaree Gaston
2004-01-01
In the context of historical climate records of China and early meteorological measurements of Beijing discovered recently in Europe, a study is undertaken on the 1743 hottest summer of north China over the last 700 a, covering Beijing, Tianjin, and the provinces of Hebei, Shanxi and Shandong, with the highest temperature reaching 44.4℃ in July 1743 in Beijing, in excess of the maximum climate record in the 20th century. Results show that the related weather/climate features of the 1743 heat wave, e.g., flood/ drought distribution and Meiyu activity and the external forcings, such as solar activity and equatorial Pacific SST condition are the same as those of the 1942 and 1999 heat events. It is noted that the 1743 burning summer event occurs in a relatively warm climate background prior to the Industrial Revolution, with a lower level of CO2 release.
Noriko eYamagishi
2016-02-01
Full Text Available Plant viral vectors are superior tools for genetic manipulation, allowing rapid induction or suppression of expression of a target gene in plants. This is a particularly effective technology for use in breeding fruit trees, which are difficult to manipulate using recombinant DNA technologies. We reported previously that if apple seed embryos (cotyledons are infected with an Apple latent spherical virus (ALSV vector (ALSV-AtFT/MdTFL1 concurrently expressing the Arabidopsis thaliana florigen (AtFT gene and suppressing the expression of the apple MdTFL1-1 gene, the period prior to initial flowering (generally lasts 5–12 years will be reduced to about two months. In this study, we examined whether or not ALSV vector technology can be used to promote flowering in pear, which undergoes a very long juvenile period (germination to flowering similar to that of apple. The MdTFL1 sequence in ALSV-AtFT/MdTFL1 was replaced with a portion of the pear PcTFL1-1 gene. The resulting virus (ALSV-AtFT/PcTFL1 and ALSV-AtFT/MdTFL1 were used individually for inoculation to pear cotyledons immediately after germination in two inoculation groups. Those inoculated with ALSV-AtFT/MdTFL1 and ALSV-AtFT/PcTFL1 then initiated flower bud formation starting one to three months after inoculation, and subsequently exhibited continuous flowering and fruition by pollination. Conversely, Japanese pear exhibited extremely low systemic infection rates when inoculated with ALSV-AtFT/MdTFL1, and failed to exhibit any induction of flowering. We also developed a simple method for eliminating ALSV vectors from infected plants. An evaluation of the method for eliminating the ALSV vectors from infected apple and pear seedlings revealed that a four-week high-temperature (37˚C incubation of ALSV-infected apples and pears disabled the movement of ALSV to new growing tissues. This demonstrates that only high-temperature treatment can easily eliminate ALSV from infected fruit trees. A method
Scogin, J. H. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)
2016-03-24
Thermogravimetric analysis with mass spectroscopy of the evolved gas (TGA-MS) is used to quantify the moisture content of materials in the 3013 destructive examination (3013 DE) surveillance program. Salts frequently present in the 3013 DE materials volatilize in the TGA and condense in the gas lines just outside the TGA furnace. The buildup of condensate can restrict the flow of purge gas and affect both the TGA operations and the mass spectrometer calibration. Removal of the condensed salts requires frequent maintenance and subsequent calibration runs to keep the moisture measurements by mass spectroscopy within acceptable limits, creating delays in processing samples. In this report, the feasibility of determining the total moisture from TGA-MS measurements at a lower temperature is investigated. A temperature of the TGA-MS analysis which reduces the complications caused by the condensation of volatile materials is determined. Analysis shows that an excellent prediction of the presently measured total moisture value can be made using only the data generated up to 700 °C and there is a sound physical basis for this estimate. It is recommended that the maximum temperature of the TGA-MS determination of total moisture for the 3013 DE program be reduced from 1000 °C to 700 °C. It is also suggested that cumulative moisture measurements at 550 °C and 700°C be substituted for the measured value of total moisture in the 3013 DE database. Using these raw values, any of predictions of the total moisture discussed in this report can be made.
Sud, Y. C.; Walker, G. K.; Zhou, Y. P.; Schmidt, Gavin A.; Lau, K. M.; Cahalan, R. F.
2008-01-01
A primary concern of CO2-induced warming is the associated rise of tropical (10S-10N) seasurface temperatures (SSTs). GISS Model-E was used to produce two sets of simulations-one with the present-day and one with doubled CO2 in the atmosphere. The intrinsic usefulness of model guidance in the tropics was confirmed when the model simulated realistic convective coupling between SSTs and atmospheric soundings and that the simulated-data correlations between SSTs and 300 hPa moiststatic energies were found to be similar to the observed. Model predicted SST limits: (i) one for the onset of deep convection and (ii) one for maximum SST, increased in the doubled C02 case. Changes in cloud heights, cloud frequencies, and cloud mass-fractions showed that convective-cloud changes increased the SSTs, while warmer mixed-layer of the doubled CO2 contained approximately 10% more water vapor; clearly that would be conducive to more intense storms and hurricanes.
Cortesi, Nicola; Peña-Angulo, Dhais; Simolo, Claudia; Stepanek, Peter; Brunetti, Michele; Gonzalez-Hidalgo, José Carlos
2014-05-01
One of the key point in the develop of the MOTEDAS dataset (see Poster 1 MOTEDAS) in the framework of the HIDROCAES Project (Impactos Hidrológicos del Calentamiento Global en España, Spanish Ministery of Research CGL2011-27574-C02-01) is the reference series for which no generalized metadata exist. In this poster we present an analysis of spatial variability of monthly minimum and maximum temperatures in the conterminous land of Spain (Iberian Peninsula, IP), by using the Correlation Decay Distance function (CDD), with the aim of evaluating, at sub-regional level, the optimal threshold distance between neighbouring stations for producing the set of reference series used in the quality control (see MOTEDAS Poster 1) and the reconstruction (see MOREDAS Poster 3). The CDD analysis for Tmax and Tmin was performed calculating a correlation matrix at monthly scale between 1981-2010 among monthly mean values of maximum (Tmax) and minimum (Tmin) temperature series (with at least 90% of data), free of anomalous data and homogenized (see MOTEDAS Poster 1), obtained from AEMEt archives (National Spanish Meteorological Agency). Monthly anomalies (difference between data and mean 1981-2010) were used to prevent the dominant effect of annual cycle in the CDD annual estimation. For each station, and time scale, the common variance r2 (using the square of Pearson's correlation coefficient) was calculated between all neighbouring temperature series and the relation between r2 and distance was modelled according to the following equation (1): Log (r2ij) = b*°dij (1) being Log(rij2) the common variance between target (i) and neighbouring series (j), dij the distance between them and b the slope of the ordinary least-squares linear regression model applied taking into account only the surrounding stations within a starting radius of 50 km and with a minimum of 5 stations required. Finally, monthly, seasonal and annual CDD values were interpolated using the Ordinary Kriging with a
Kremser, S.; Bodeker, G. E.; Lewis, J.
2014-01-01
A Climate Pattern-Scaling Model (CPSM) that simulates global patterns of climate change, for a prescribed emissions scenario, is described. A CPSM works by quantitatively establishing the statistical relationship between a climate variable at a specific location (e.g. daily maximum surface temperature, Tmax) and one or more predictor time series (e.g. global mean surface temperature, Tglobal) - referred to as the "training" of the CPSM. This training uses a regression model to derive fit coefficients that describe the statistical relationship between the predictor time series and the target climate variable time series. Once that relationship has been determined, and given the predictor time series for any greenhouse gas (GHG) emissions scenario, the change in the climate variable of interest can be reconstructed - referred to as the "application" of the CPSM. The advantage of using a CPSM rather than a typical atmosphere-ocean global climate model (AOGCM) is that the predictor time series required by the CPSM can usually be generated quickly using a simple climate model (SCM) for any prescribed GHG emissions scenario and then applied to generate global fields of the climate variable of interest. The training can be performed either on historical measurements or on output from an AOGCM. Using model output from 21st century simulations has the advantage that the climate change signal is more pronounced than in historical data and therefore a more robust statistical relationship is obtained. The disadvantage of using AOGCM output is that the CPSM training might be compromised by any AOGCM inadequacies. For the purposes of exploring the various methodological aspects of the CPSM approach, AOGCM output was used in this study to train the CPSM. These investigations of the CPSM methodology focus on monthly mean fields of daily temperature extremes (Tmax and Tmin). The methodological aspects of the CPSM explored in this study include (1) investigation of the advantage
Schmid, W.
2002-07-01
This article describes the clever combination of various techniques to achieve the goal of providing a stable ambient temperature with an accuracy of +/- 1 K in the assembly shop of a German manufacturer of precision machine tools. The requirements placed on the assembly and operation of machine tools operating to an accuracy of less that a hundredth of a millimetre are discussed. The award-winning heating and cooling system, which features the use of gravity cooling, geothermal energy (ground water for cooling) and the use of constructional elements (floor, facades, windows) for thermal buffering is described. The ingenious control system with 32 control zones and 64 sensors is described, which also provides the company's management with long-term documentation of temperature conditions for quality assurance purposes. Technical data on the installation is provided in table form.
Thermodynamic hardness and the maximum hardness principle
Franco-Pérez, Marco; Gázquez, José L.; Ayers, Paul W.; Vela, Alberto
2017-08-01
An alternative definition of hardness (called the thermodynamic hardness) within the grand canonical ensemble formalism is proposed in terms of the partial derivative of the electronic chemical potential with respect to the thermodynamic chemical potential of the reservoir, keeping the temperature and the external potential constant. This temperature dependent definition may be interpreted as a measure of the propensity of a system to go through a charge transfer process when it interacts with other species, and thus it keeps the philosophy of the original definition. When the derivative is expressed in terms of the three-state ensemble model, in the regime of low temperatures and up to temperatures of chemical interest, one finds that for zero fractional charge, the thermodynamic hardness is proportional to T-1(I -A ) , where I is the first ionization potential, A is the electron affinity, and T is the temperature. However, the thermodynamic hardness is nearly zero when the fractional charge is different from zero. Thus, through the present definition, one avoids the presence of the Dirac delta function. We show that the chemical hardness defined in this way provides meaningful and discernible information about the hardness properties of a chemical species exhibiting integer or a fractional average number of electrons, and this analysis allowed us to establish a link between the maximum possible value of the hardness here defined, with the minimum softness principle, showing that both principles are related to minimum fractional charge and maximum stability conditions.
Wen, Xinyu; Liu, Zhengyu; Chen, Zhongxiao; Brady, Esther; Noone, David; Zhu, Qingzhao; Guan, Jian
2016-11-01
Water isotopes in precipitation have played a key role in the reconstruction of past climate on millennial timescales and longer. However, for midlatitude regions like East Asia with complex terrain, the reliability behind the basic assumptions of the temperature effect and amount effect is based on modern observational data and still remains unclear for past climate. In the present work, we reexamine the two basic effects on seasonal, interannual, and millennial timescales in a set of time slice experiments for the period 22-0 ka using an isotope-enabled atmospheric general circulation model (AGCM). Our study confirms the robustness of the temperature and amount effects on the seasonal cycle over China in the present climatic conditions, with the temperature effect dominating in northern China and the amount effect dominating in the far south of China but no distinct effect in the transition region of central China. However, our analysis shows that neither temperature nor amount effect is significantly dominant over China on millennial and interannual timescales, which is a challenge to those classic assumptions in past climate reconstruction. Our work helps shed light on the interpretation of the proxy record of δ18O from a modeling point of view.
Vezzoli, G. C.; Burke, T.; Chen, M. F.; Craver, F.; Stanley, W.
1992-09-01
We have studied the pre-onset deviation-from-linearity region, the transitional regime, and the foot region in the resistance versus temperature behavior of high-T sub c oxide superconductors, employing time varying magnetic fields and carefully controlled precise temperatures. We have shown that the best value of T sub c can be extrapolated from the magnetic field induced divergence of the resistance versus inverse absolute temperature data as derived from the transitional and/or foot regions. These data are in accord with results from previous Hall effect studies. The pre-onset region however, shows a differing behavior (in R versus 1000/T as a function of B) which we believe links it to an incipient Cooper pairing that suffers a kinetic barrier opposing formation of a full supercurrent. This kinetic dependence is believed to be associated with the lifetime of the mediator particle. This particle is interpreted to be the virtual exciton formed from internal-field induced charge-transfer excitations which transiently neutralize the multivalence cations and establish bound holes on the oxygens.
Vezzoli, G.C.; Burke, T.; Chen, M.F.; Craver, F.; Stanley, W.
1992-09-01
We have studied the pre-onset deviation-from-linearity region, the transitional regime, and the foot region in the resistance versus temperature behavior of high-T sub c oxdie superconductors, employing time varying magnetic fields and carefully controlled precise temperatures. We have shown that the best value of T sub c can be extrapolated from the magnetic field induced divergence of the resistance versus inverse absolute temperature data as derived from the transitional and/or foot regions. These data are in accord with results from previous Hall effect studies. The pre-onset region however, shows a differing behavior (in R versus 1000/T as a function of B) which we believe links it to an incipient Cooper pairing that suffers a kinetic barrier opposing formation of a full supercurrent. This kinetic dependence is believed to be associated with the lifetime of the mediator particle. This particle is interpreted to be the virtual exciton formed from internal-field induced charge-transfer excitations which transiently neutralize the multivalence cations and establish bound holes on the oxygens.
2004-01-01
A 13 kA current lead, measuring 1.5 m in length. The lower part consists of a high-temperature superconductor (Bi-2223), operating at between 50 K and 4.5 K, while the heat-exchanger upper part allows the current to be brought from room temperature to 50 K.
Rubin, Stephen P.; Reisenbichler, Reginald R.; Slatton, Stacey L.; Rubin, Stephen P.; Reisenbichler, Reginald R.; Wetzel, Lisa A.; Hayes, Michael C.
2012-01-01
The accuracy of a model that predicts time between fertilization and maximum alevin wet weight (MAWW) from incubation temperature was tested for steelhead Oncorhynchus mykiss from Dworshak National Fish Hatchery on the Clearwater River, Idaho. MAWW corresponds to the button-up fry stage of development. Embryos were incubated at warm (mean=11.6°C) or cold (mean=7.3°C) temperatures and time between fertilization and MAWW was measured for each temperature. Model predictions of time to MAWW were within 1% of measured time to MAWW. Mean egg weight ranged from 0.101-0.136 g among females (mean = 0.116). Time to MAWW was positively related to egg size for each temperature, but the increase in time to MAWW with increasing egg size was greater for embryos reared at the warm than at the cold temperature. We developed equations accounting for the effect of egg size on time to MAWW for each temperature, and also for the mean of those temperatures (9.3°C).
Annika K. Jägerbrand
2016-04-01
Full Text Available There is limited knowledge available on the thermal acclimation processes for bryophytes, especially when considering variation between populations or sites. This study investigated whether short-term ex situ thermal acclimation of different populations showed patterns of site dependency and whether the maximum quantum yield of PSII (Fv/Fm could be used as an indicator of adaptation or temperature stress in two bryophyte species: Pleurozium schreberi (Willd. ex Brid. Mitt. and Racomitrium lanuginosum (Hedw. Brid. We sought to test the hypothesis that differences in the ability to acclimate to short-term temperature treatment would be revealed as differences in photosystem II maximum yield (Fv/Fm. Thermal treatments were applied to samples from 12 and 11 populations during 12 or 13 days in growth chambers and comprised: (1 10/5 °C; (2 20/10 °C; (3 25/15 °C; (4 30/20 °C (12 hours day/night temperature. In Pleurozium schreberi, there were no significant site-dependent differences before or after the experiment, while site dependencies were clearly shown in Racomitrium lanuginosum throughout the study. Fv/Fm in Pleurozium schreberi decreased at the highest and lowest temperature treatments, which can be interpreted as a stress response, but no similar trends were shown by Racomitrium lanuginosum.
朱伟; 周晓峰; 胡隆华; 刘帅
2012-01-01
Experimental study of temperature distribution along tunnel ceiling with different longitudinal ventilation velocities and different typical fire sizes was conducted in a combustion wind tunnel with length of 20 m. Both square and rectangular pool fires were used as fire sources for longitudinal ventilation velocities ranged in 0 - 3 m/s. The smoke temperatures below the ceiling were recorded by K type thermocouple for near fire region and by thermal resistors for that relative far away from the fire source. The results indicate that longitudinal ventilation velocity and fire size have a great influence on temperature distribution. The variation of ceiling temperature distribution with the increase of longitudinal ventilation velocity was shown to be different for a small fire fromthat for a large fire. For small scale fires, temperature of tunnel ceiling reduced to a stable value with gradual increase of longitudinal ventilation velocity. However, for big scale fire, the temperature increased first, and then decreased. The position of maximum temperature rise point firstly moved downstream horizontally with the increase of the wind speed. When the wind speed reached a certain value, the maximum temperature rise point returned back to an upstream position, and then moved downstream again. This is due to the change of dominant heating mechanism with the increase of longitudinal ventilation velocity. When the longitudinal ventilation velocity is relative small, both convection from hot smoke and radiation from the flame provide considerable contribution. However , when the longitudinal ventilation velocity is relative large, radiation is dominant. The influence of the length of windward side of rectangular pool fire was also discussed. It was shown that when the longitudinal ventilation velocity is relative smaller (0.5 - 1.5 m/s), the maximum temperature is higher when the longer side is parallel to the wind direction than that under perpendicular condition. However
Greenslade, Thomas B., Jr.
1985-01-01
Discusses a series of experiments performed by Thomas Hope in 1805 which show the temperature at which water has its maximum density. Early data cast into a modern form as well as guidelines and recent data collected from the author provide background for duplicating Hope's experiments in the classroom. (JN)
F. TopsÃƒÂ¸e
2001-09-01
Full Text Available Abstract: In its modern formulation, the Maximum Entropy Principle was promoted by E.T. Jaynes, starting in the mid-fifties. The principle dictates that one should look for a distribution, consistent with available information, which maximizes the entropy. However, this principle focuses only on distributions and it appears advantageous to bring information theoretical thinking more prominently into play by also focusing on the "observer" and on coding. This view was brought forward by the second named author in the late seventies and is the view we will follow-up on here. It leads to the consideration of a certain game, the Code Length Game and, via standard game theoretical thinking, to a principle of Game Theoretical Equilibrium. This principle is more basic than the Maximum Entropy Principle in the sense that the search for one type of optimal strategies in the Code Length Game translates directly into the search for distributions with maximum entropy. In the present paper we offer a self-contained and comprehensive treatment of fundamentals of both principles mentioned, based on a study of the Code Length Game. Though new concepts and results are presented, the reading should be instructional and accessible to a rather wide audience, at least if certain mathematical details are left aside at a rst reading. The most frequently studied instance of entropy maximization pertains to the Mean Energy Model which involves a moment constraint related to a given function, here taken to represent "energy". This type of application is very well known from the literature with hundreds of applications pertaining to several different elds and will also here serve as important illustration of the theory. But our approach reaches further, especially regarding the study of continuity properties of the entropy function, and this leads to new results which allow a discussion of models with so-called entropy loss. These results have tempted us to speculate over
Maximum Autocorrelation Factorial Kriging
Nielsen, Allan Aasbjerg; Conradsen, Knut; Pedersen, John L.
2000-01-01
This paper describes maximum autocorrelation factor (MAF) analysis, maximum autocorrelation factorial kriging, and its application to irregularly sampled stream sediment geochemical data from South Greenland. Kriged MAF images are compared with kriged images of varimax rotated factors from...
董丹宏; 黄刚
2015-01-01
Based on daily maximum and minimum temperature data from 740 homogenized surface meteorological stations, the present study investigates the regional characteristics of the temperature trend and the dependence of maximum and minimum temperature and diurnal temperature range changes on the altitude during the period 1963–2012. It is found that the magnitude of minimum temperature increase is larger than that of the maximum temperature increase. The significant warming areas are located at high altitude, all of which increase remarkably in size during the study period. The maximum and minimum temperature and diurnal temperature range trends increase with altitude, except in spring. The correlation coefficients between the maximum temperature trend and altitude are the highest. At the same altitude, the amplitudes of maximum and minimum temperature show inconsistency: They exhibit increasing trends in the 1990s, with significant change at low altitude; they change minimally in the 1980s; and at high altitudes (above 2000 m), the magnitudes of their changes are weak before the 1990s but stronger in the last 10 years of the study period. The seasonal variability of the diurnal temperature range is large over 2000 m, decreasing in summer but increasing in winter. Before the 1990s, there is no significant variation between maximum and minimum temperature and altitude. However, their trends almost all decrease and then increase with altitude in the last 20 years. Additionally, the response to climate in highland areas is more sensitive than that in lowland areas.%本文利用中国740个气象台站1963～2012年均一化逐日最高温度和最低温度资料，分析了中国地区最高、最低气温和日较差变化趋势的区域特征及其与海拔高度的关系。结果表明：近50年气温的变化趋势无论是年或季节变化，最低温度的增温幅度都高于最高温度，且其增温显著区域都对应我国高海拔地区。除了春季，
42 CFR 50.504 - Allowable cost of drugs.
2010-10-01
... 42 Public Health 1 2010-10-01 2010-10-01 false Allowable cost of drugs. 50.504 Section 50.504... APPLICABILITY Maximum Allowable Cost for Drugs § 50.504 Allowable cost of drugs. (a) The maximum amount which may be expended from program funds for the acquisition of any drug shall be the lowest of (1)...
Maximum Entropy in Drug Discovery
Chih-Yuan Tseng
2014-07-01
Full Text Available Drug discovery applies multidisciplinary approaches either experimentally, computationally or both ways to identify lead compounds to treat various diseases. While conventional approaches have yielded many US Food and Drug Administration (FDA-approved drugs, researchers continue investigating and designing better approaches to increase the success rate in the discovery process. In this article, we provide an overview of the current strategies and point out where and how the method of maximum entropy has been introduced in this area. The maximum entropy principle has its root in thermodynamics, yet since Jaynes’ pioneering work in the 1950s, the maximum entropy principle has not only been used as a physics law, but also as a reasoning tool that allows us to process information in hand with the least bias. Its applicability in various disciplines has been abundantly demonstrated. We give several examples of applications of maximum entropy in different stages of drug discovery. Finally, we discuss a promising new direction in drug discovery that is likely to hinge on the ways of utilizing maximum entropy.
Schmidt, Joachim; Opgenoorth, Lars; Martens, Jochen; Miehe, Georg
2011-07-01
Previous findings regarding the Last Glacial Maximum LGM summer temperature depression (maxΔT in July) on the Tibetan Plateau varied over a large range (between 0 and 9 °C). Geologic proxies usually provided higher values than palynological data. Because of this wide temperature range, it was hitherto impossible to reconstruct the glacial environment of the Tibetan Plateau. Here, we present for the first time data indicating that local neoendemics of modern species groups are promising proxies for assessing the LGM temperature depression in Tibet. We used biogeographical and phylogenetic data from small, wingless edaphous ground beetles of the genus Trechus, and from private juniper tree haplotypes. The derived values of the maxΔT in July ranged between 3 and 4 °C. Our data support previous findings that were based on palynological data. At the same time, our data are spatially more specific as they are not bound to specific archives. Our study shows that the use of modern endemics enables a detailed mapping of local LGM conditions in High Asia. A prerequisite for this is an extensive biogeographical and phylogenetic exploration of the area and the inclusion of additional endemic taxa and evolutionary lines.
陈嘉; 李拥军; 杨文萍
2009-01-01
Objective To study the effects of carbon disulfide exposure within the national maximum allowable concentration(MAC) on blood pressure and electrocardiogram, and associations with selected factors. Methods Workers in a chemical fiber factory were divided into two groups based on the type of work: a high exposure group (HEG) of 821 individuals and a low exposure group (LEG) of 259. The CS_2 concentration at workplace was controlled under the national MAC. A set of 250 randomly selected people taking routine phys-ical check-ups in the same period and hospital constituted the control group. The systolic blood pressure (SBP) and diastolic hlood pressure (DBP) were measured on the arm, and the pulse pressure (PP) and mean arterial blood pressure (MABP) were calculated based on SBP and DBP. The blood pressure data, along with the results of the routine 12-lead electrocardiography taken at rest and records on gender, age, years of work, type of work, and concentrations of triglycerol, cholesterol, and glucose in blood, were compiled for analyses. Risk factors upon CS_2 exposure for the increase of blood pressure and occurrence of electrocardiogram abnor-malities were identified and rationalized. Results Significant difference (P<0.01) in the average values of SBP, DBP, MABP, and the corresponding abnormality incident rates was found between HEG and LEG, and between HEG and the control group. For both HEG and LEG, the incident rate of DBP abnormality(high DBP) is nearly two times as high as that of SBP. Type of work is the largest risk factor in both the high SBP and high DBP subgroups, with odds ratios (OR) of 2.086 and 2.331 respectively, and high CS_2 exposure presents more than double the risk than low exposure. On the incident rate of ECG abnormalities, beth exposure groups are significantly different (P<0.01) to the control group. High SBP in LEG and high DBP in HEG were found to be significant risk factors (OR = 3.531 and 1.638 respectively), while blood glucose
Maximum Autocorrelation Factorial Kriging
Nielsen, Allan Aasbjerg; Conradsen, Knut; Pedersen, John L.; Steenfelt, Agnete
2000-01-01
This paper describes maximum autocorrelation factor (MAF) analysis, maximum autocorrelation factorial kriging, and its application to irregularly sampled stream sediment geochemical data from South Greenland. Kriged MAF images are compared with kriged images of varimax rotated factors from an ordinary non-spatial factor analysis, and they are interpreted in a geological context. It is demonstrated that MAF analysis contrary to ordinary non-spatial factor analysis gives an objective discrimina...
Generalised maximum entropy and heterogeneous technologies
Oude Lansink, A.G.J.M.
1999-01-01
Generalised maximum entropy methods are used to estimate a dual model of production on panel data of Dutch cash crop farms over the period 1970-1992. The generalised maximum entropy approach allows a coherent system of input demand and output supply equations to be estimated for each farm in the sam
徐革锋; 尹家胜; 韩英; 刘洋; 牟振波
2014-01-01
This study examined the effects of water temperature on the metabolic characteristics and aerobic exer-cise capacity of juvenile manchurian trout , Brachymystax lenok ( Pallas) .The resting metabolic rate ( RMR) ,maxi-mum metabolic rate (MMR), metabolic scope(MS)and critical swimming speed (UCrit) of juveniles were measured at different temperature (4, 8, 12, 16, 20℃).The results showed that both the RMR and the MMR increased sig-nificantly with the increasing of water temperature ( P<0 .05 ) .Compared with test group at 4℃, the RMR for 8℃, 12℃, 16℃ and 20℃increased by 62%, 165%, 390%, 411%,respectively, and the MMR increased by 3%, 34%, 111%, 115%, respectively .However , the MS decreased with the increasing of water temperature with the highest MS occurring at 4℃.UCrit was significantly affected by water temperature (P<0.05), but the varia-tions of UCrit didn′t follow certain pattern with temperature .In the test of aerobic exercise , the MMR for each tem-perature level occurred at the swimming speed of 70% UCrit , probably due to the start of anaerobic metabolism , which caused excessive creatine in body , consequently hindered the aerobic metabolism .%为了探究温度对细鳞鲑（ Brachymystax lenok）幼鱼的代谢特征和有氧运动能力的影响，在不同温度（4℃、8℃、12℃、16℃、20℃）下测定了实验鱼的静止代谢率（ RMR）、有氧运动过程中的最大代谢率（ MMR）以及能量代谢范围（MS）和临界游泳速度（UCrit）。结果表明，随着温度的上升，RMR和MMR均显著提高（P＜0．05），各温度下的RMR和MMR分别较4℃条件的提高了62％（8℃）、165％（12℃）、390％（16℃）、411％（20℃）和3％（8℃）、34％（12℃）、111％（16℃）、115％（20℃）；MS随水温的升高呈现下降的趋势，且4℃条件具有最大的代谢范围。不同温度条件下UCrit存在显著性差异，但随着温度升高未表现出明显的变
Maximum likely scale estimation
Loog, Marco; Pedersen, Kim Steenstrup; Markussen, Bo
2005-01-01
A maximum likelihood local scale estimation principle is presented. An actual implementation of the estimation principle uses second order moments of multiple measurements at a fixed location in the image. These measurements consist of Gaussian derivatives possibly taken at several scales and/or ...
Simone Bittencourt
2006-06-01
Full Text Available Para implementação e operacionalização da política brasileira de recursos hídricos, é imprescindível o uso de ferramentas de planejamento que considerem o efeito de todas as atividades ou processos que causam ou contribuem para a degradação da qualidade de um corpo d'água. Neste sentido, aplicou-se o processo TMDL (total maximum daily load, desenvolvido pela Agência de Proteção Ambiental dos Estados Unidos (EPA, para o P, na área de drenagem de contribuição ao futuro reservatório Piraquara II, bacia hidrográfica do rio Piraquara, Paraná. O processo TMDL determina a quantidade máxima de cargas de um poluente que um corpo d'água pode receber sem violar os padrões estabelecidos de qualidade da água e aloca cargas deste poluente entre fontes de poluição pontuais e difusas. No presente estudo, utilizou-se o método TMDL, com o objetivo de demonstrar ser ele uma ferramenta útil no processo de gestão dos recursos hídricos. Simularam-se cenários de uso do solo, por meio de modelagem matemática, até obter-se uma concentração de P total no reservatório abaixo da faixa limite para ocorrência de eutrofização, de 0,025 a 0,10 mg L-1, estabelecida no estudo. Realizou-se uma simulação de uso atual do solo, visando prever a condição inicial de qualidade da água no corpo d'água, na qual a concentração de P total no reservatório resultante não atendeu ao padrão estabelecido. Procedeu-se a uma segunda simulação com adoção das medidas de controle, recomposição de mata ciliar e plantio direto, para reduzir a exportação de carga de P total da bacia. Obteve-se uma melhoria na qualidade da água do reservatório, indicando que as medidas adotadas foram suficientes para atingir o padrão estabelecido, o que demonstra a aplicabilidade do método.For the implementation and operation of the Brazilian Federal law on water resources of 1997 it is indispensable to use planning tools that take into account the effect of
Maximum information photoelectron metrology
Hockett, P; Wollenhaupt, M; Baumert, T
2015-01-01
Photoelectron interferograms, manifested in photoelectron angular distributions (PADs), are a high-information, coherent observable. In order to obtain the maximum information from angle-resolved photoionization experiments it is desirable to record the full, 3D, photoelectron momentum distribution. Here we apply tomographic reconstruction techniques to obtain such 3D distributions from multiphoton ionization of potassium atoms, and fully analyse the energy and angular content of the 3D data. The PADs obtained as a function of energy indicate good agreement with previous 2D data and detailed analysis [Hockett et. al., Phys. Rev. Lett. 112, 223001 (2014)] over the main spectral features, but also indicate unexpected symmetry-breaking in certain regions of momentum space, thus revealing additional continuum interferences which cannot otherwise be observed. These observations reflect the presence of additional ionization pathways and, most generally, illustrate the power of maximum information measurements of th...
Maximum-entropy for the laser fusion problem
Madkour, M.A. [Nansoura Univ. (Egypt). Dept. of Phys.
1996-09-01
The problem of heat flux at the critical surfaces and the surfaces of a pellet of deuterium and tritium (conduction zone) heated by laser have been considered. Ion-electron collisions are only allowed for: i.e. the linear transport equation is used to describe the problem with boundary conditions. The maximum-entropy approach is used to calculate the electron density and temperature across the conduction zone as well as the heat flux. Numerical results are given and compared with those of Rouse and Williams and El-Wakil et al. (orig.).
Maximum Likelihood Associative Memories
Gripon, Vincent; Rabbat, Michael
2013-01-01
Associative memories are structures that store data in such a way that it can later be retrieved given only a part of its content -- a sort-of error/erasure-resilience property. They are used in applications ranging from caches and memory management in CPUs to database engines. In this work we study associative memories built on the maximum likelihood principle. We derive minimum residual error rates when the data stored comes from a uniform binary source. Second, we determine the minimum amo...
Maximum likely scale estimation
Loog, Marco; Pedersen, Kim Steenstrup; Markussen, Bo
2005-01-01
A maximum likelihood local scale estimation principle is presented. An actual implementation of the estimation principle uses second order moments of multiple measurements at a fixed location in the image. These measurements consist of Gaussian derivatives possibly taken at several scales and....../or having different derivative orders. Although the principle is applicable to a wide variety of image models, the main focus here is on the Brownian model and its use for scale selection in natural images. Furthermore, in the examples provided, the simplifying assumption is made that the behavior...... of the measurements is completely characterized by all moments up to second order....
The maximum entropy technique. System's statistical description
Belashev, B Z
2002-01-01
The maximum entropy technique (MENT) is applied for searching the distribution functions of physical values. MENT takes into consideration the demand of maximum entropy, the characteristics of the system and the connection conditions, naturally. It is allowed to apply MENT for statistical description of closed and open systems. The examples in which MENT had been used for the description of the equilibrium and nonequilibrium states and the states far from the thermodynamical equilibrium are considered
Maximum permissible voltage of YBCO coated conductors
Wen, J.; Lin, B.; Sheng, J.; Xu, J.; Jin, Z. [Department of Electrical Engineering, Shanghai Jiao Tong University, Shanghai (China); Hong, Z., E-mail: zhiyong.hong@sjtu.edu.cn [Department of Electrical Engineering, Shanghai Jiao Tong University, Shanghai (China); Wang, D.; Zhou, H.; Shen, X.; Shen, C. [Qingpu Power Supply Company, State Grid Shanghai Municipal Electric Power Company, Shanghai (China)
2014-06-15
Highlights: • We examine three kinds of tapes’ maximum permissible voltage. • We examine the relationship between quenching duration and maximum permissible voltage. • Continuous I{sub c} degradations under repetitive quenching where tapes reaching maximum permissible voltage. • The relationship between maximum permissible voltage and resistance, temperature. - Abstract: Superconducting fault current limiter (SFCL) could reduce short circuit currents in electrical power system. One of the most important thing in developing SFCL is to find out the maximum permissible voltage of each limiting element. The maximum permissible voltage is defined as the maximum voltage per unit length at which the YBCO coated conductors (CC) do not suffer from critical current (I{sub c}) degradation or burnout. In this research, the time of quenching process is changed and voltage is raised until the I{sub c} degradation or burnout happens. YBCO coated conductors test in the experiment are from American superconductor (AMSC) and Shanghai Jiao Tong University (SJTU). Along with the quenching duration increasing, the maximum permissible voltage of CC decreases. When quenching duration is 100 ms, the maximum permissible of SJTU CC, 12 mm AMSC CC and 4 mm AMSC CC are 0.72 V/cm, 0.52 V/cm and 1.2 V/cm respectively. Based on the results of samples, the whole length of CCs used in the design of a SFCL can be determined.
Regularized maximum correntropy machine
Wang, Jim Jing-Yan
2015-02-12
In this paper we investigate the usage of regularized correntropy framework for learning of classifiers from noisy labels. The class label predictors learned by minimizing transitional loss functions are sensitive to the noisy and outlying labels of training samples, because the transitional loss functions are equally applied to all the samples. To solve this problem, we propose to learn the class label predictors by maximizing the correntropy between the predicted labels and the true labels of the training samples, under the regularized Maximum Correntropy Criteria (MCC) framework. Moreover, we regularize the predictor parameter to control the complexity of the predictor. The learning problem is formulated by an objective function considering the parameter regularization and MCC simultaneously. By optimizing the objective function alternately, we develop a novel predictor learning algorithm. The experiments on two challenging pattern classification tasks show that it significantly outperforms the machines with transitional loss functions.
Quantum theory allows for absolute maximal contextuality
Amaral, Barbara; Cunha, Marcelo Terra; Cabello, Adán
2015-12-01
Contextuality is a fundamental feature of quantum theory and a necessary resource for quantum computation and communication. It is therefore important to investigate how large contextuality can be in quantum theory. Linear contextuality witnesses can be expressed as a sum S of n probabilities, and the independence number α and the Tsirelson-like number ϑ of the corresponding exclusivity graph are, respectively, the maximum of S for noncontextual theories and for the theory under consideration. A theory allows for absolute maximal contextuality if it has scenarios in which ϑ /α approaches n . Here we show that quantum theory allows for absolute maximal contextuality despite what is suggested by the examination of the quantum violations of Bell and noncontextuality inequalities considered in the past. Our proof is not constructive and does not single out explicit scenarios. Nevertheless, we identify scenarios in which quantum theory allows for almost-absolute-maximal contextuality.
Economics and Maximum Entropy Production
Lorenz, R. D.
2003-04-01
Price differentials, sales volume and profit can be seen as analogues of temperature difference, heat flow and work or entropy production in the climate system. One aspect in which economic systems exhibit more clarity than the climate is that the empirical and/or statistical mechanical tendency for systems to seek a maximum in production is very evident in economics, in that the profit motive is very clear. Noting the common link between 1/f noise, power laws and Self-Organized Criticality with Maximum Entropy Production, the power law fluctuations in security and commodity prices is not inconsistent with the analogy. There is an additional thermodynamic analogy, in that scarcity is valued. A commodity concentrated among a few traders is valued highly by the many who do not have it. The market therefore encourages via prices the spreading of those goods among a wider group, just as heat tends to diffuse, increasing entropy. I explore some empirical price-volume relationships of metals and meteorites in this context.
40 CFR 35.2025 - Allowance and advance of allowance.
2010-07-01
... facilities planning and design of the project and Step 7 agreements will include an allowance for facility planning in accordance with appendix B of this subpart. (b) Advance of allowance to potential grant... grant applicants for facilities planning and project design. (2) The State may request that the right to...
2010-10-01
...) of this section, additional design features, such as mechanical or composite crack arrestors and/or... surface of the plate/coil or pipe to identify imperfections that impair serviceability such as laminations... must be a hardness test, using Vickers (Hv10) hardness test method or equivalent test method, to...
5 CFR 591.104 - Higher initial maximum uniform allowance rate.
2010-01-01
... specific items required for the basic uniform and the average total uniform cost for the affected employees... requirement. (e) So that OPM can evaluate agencies' use of this authority and provide the Congress and others... initial year a new style or type of minimum basic uniform is required for a category of employees, an...
49 CFR 192.620 - Alternative maximum allowable operating pressure for certain steel pipelines.
2010-10-01
... integrity of the coating using direct current voltage gradient (DCVG) or alternating current voltage... pipeline segment. (ii) To address interference currents, perform the following: (A) Conduct an interference survey to detect the presence and level of any electrical current that could impact external...
D. Evans
2015-07-01
Full Text Available Much of our knowledge of past ocean temperatures comes from the foraminifera Mg / Ca palaeothermometer. Several non-thermal controls on foraminifera Mg incorporation have been identified, of which vital-effects, salinity and secular variation in seawater Mg / Ca are the most commonly considered. Ocean carbonate chemistry is also known to influence Mg / Ca, yet this is rarely considered as a source of uncertainty either because (1 precise pH and [CO32−] reconstructions are sparse, or (2 it is not clear from existing culture studies how a correction should be applied. We present new culture data of the relationship between carbonate chemistry for the surface-dwelling planktic species Globigerinoides ruber, and compare our results to data compiled from existing studies. We find a coherent relationship between Mg / Ca and the carbonate system and argue that pH rather than [CO32−] is likely to be the dominant control. Applying these new calibrations to datasets for the Paleocene–Eocene Thermal Maximum (PETM and Eocene–Oligocene Transition (EOT enable us to produce a more accurate picture of surface hydrology change for the former, and a reassessment of the amount of subtropical precursor cooling for the latter. We show that properly corrected Mg / Ca and δ18O datasets for the PETM imply no salinity change, and that the amount of precursor cooling over the EOT has been previously underestimated by ∼ 2 °C based on Mg / Ca. Finally, we present new laser-ablation data of EOT-age Turborotalia ampliapertura from St Stephens Quarry (Alabama, for which a solution ICPMS Mg / Ca record is available (Wade et al., 2012. We show that the two datasets are in excellent agreement, demonstrating that fossil solution and laser-ablation data may be directly comparable. Together with an advancing understanding of the effect of Mg / Casw, the coherent picture of the relationship between Mg / Ca and pH that we outline here represents a step towards producing
Evans, David; Wade, Bridget S.; Henehan, Michael; Erez, Jonathan; Müller, Wolfgang
2016-04-01
Much of our knowledge of past ocean temperatures comes from the foraminifera Mg / Ca palaeothermometer. Several nonthermal controls on foraminifera Mg incorporation have been identified, of which vital effects, salinity, and secular variation in seawater Mg / Ca are the most commonly considered. Ocean carbonate chemistry is also known to influence Mg / Ca, yet this is rarely examined as a source of uncertainty, either because (1) precise pH and [CO32-] reconstructions are sparse or (2) it is not clear from existing culture studies how a correction should be applied. We present new culture data of the relationship between carbonate chemistry and Mg / Ca for the surface-dwelling planktic species Globigerinoides ruber and compare our results to data compiled from existing studies. We find a coherent relationship between Mg / Ca and the carbonate system and argue that pH rather than [CO32-] is likely to be the dominant control. Applying these new calibrations to data sets for the Paleocene-Eocene Thermal Maximum (PETM) and Eocene-Oligocene transition (EOT) enables us to produce a more accurate picture of surface hydrology change for the former and a reassessment of the amount of subtropical precursor cooling for the latter. We show that pH-adjusted Mg / Ca and δ18O data sets for the PETM are within error of no salinity change and that the amount of precursor cooling over the EOT has been previously underestimated by ˜ 2 °C based on Mg / Ca. Finally, we present new laser-ablation data of EOT-age Turborotalia ampliapertura from St. Stephens Quarry (Alabama), for which a solution inductively coupled plasma mass spectrometry (ICPMS) Mg / Ca record is available (Wade et al., 2012). We show that the two data sets are in excellent agreement, demonstrating that fossil solution and laser-ablation data may be directly comparable. Together with an advancing understanding of the effect of Mg / Casw, the coherent picture of the relationship between Mg / Ca and pH that we outline
Equalized near maximum likelihood detector
2012-01-01
This paper presents new detector that is used to mitigate intersymbol interference introduced by bandlimited channels. This detector is named equalized near maximum likelihood detector which combines nonlinear equalizer and near maximum likelihood detector. Simulation results show that the performance of equalized near maximum likelihood detector is better than the performance of nonlinear equalizer but worse than near maximum likelihood detector.
Cheeseman, Peter; Stutz, John
2005-01-01
A long standing mystery in using Maximum Entropy (MaxEnt) is how to deal with constraints whose values are uncertain. This situation arises when constraint values are estimated from data, because of finite sample sizes. One approach to this problem, advocated by E.T. Jaynes [1], is to ignore this uncertainty, and treat the empirically observed values as exact. We refer to this as the classic MaxEnt approach. Classic MaxEnt gives point probabilities (subject to the given constraints), rather than probability densities. We develop an alternative approach that assumes that the uncertain constraint values are represented by a probability density {e.g: a Gaussian), and this uncertainty yields a MaxEnt posterior probability density. That is, the classic MaxEnt point probabilities are regarded as a multidimensional function of the given constraint values, and uncertainty on these values is transmitted through the MaxEnt function to give uncertainty over the MaXEnt probabilities. We illustrate this approach by explicitly calculating the generalized MaxEnt density for a simple but common case, then show how this can be extended numerically to the general case. This paper expands the generalized MaxEnt concept introduced in a previous paper [3].
Maximum entropy production in daisyworld
Maunu, Haley A.; Knuth, Kevin H.
2012-05-01
Daisyworld was first introduced in 1983 by Watson and Lovelock as a model that illustrates how life can influence a planet's climate. These models typically involve modeling a planetary surface on which black and white daisies can grow thus influencing the local surface albedo and therefore also the temperature distribution. Since then, variations of daisyworld have been applied to study problems ranging from ecological systems to global climate. Much of the interest in daisyworld models is due to the fact that they enable one to study self-regulating systems. These models are nonlinear, and as such they exhibit sensitive dependence on initial conditions, and depending on the specifics of the model they can also exhibit feedback loops, oscillations, and chaotic behavior. Many daisyworld models are thermodynamic in nature in that they rely on heat flux and temperature gradients. However, what is not well-known is whether, or even why, a daisyworld model might settle into a maximum entropy production (MEP) state. With the aim to better understand these systems, this paper will discuss what is known about the role of MEP in daisyworld models.
20 CFR 617.14 - Maximum amount of TRA.
2010-04-01
... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Maximum amount of TRA. 617.14 Section 617.14... FOR WORKERS UNDER THE TRADE ACT OF 1974 Trade Readjustment Allowances (TRA) § 617.14 Maximum amount of TRA. (a) General rule. Except as provided under paragraph (b) of this section, the maximum amount of...
吴普; 王丽丽; 邵雪梅
2008-01-01
Having analyzed the tree ring width and maximum latewood density of Pinus den-sata from west Sichuan, we obtained different climate information from tree-ring width and maximum latewood density chronology. The growth of tree ring width was responded princi-pally to the precipitation in current May, which might be influenced by the activity of southwest monsoon, whereas the maximum latewood density reflected summer temperature (June-September). According to the correlation relationship, a transfer function had been used to reconstruct summer temperature for the study area. The explained variance of re-construction is 51% (F=-52.099, p<0.0001). In the reconstruction series: before the 1930s, the climate was relatively cold, and relatively warm from 1930 to 1960, this trend was in accor-dance with the cold-warm period of the last 100 years, west Sichuan. Compared with Chengdu, the warming break point in west Sichuan is 3 years ahead of time, indicating that the Tibetan Plateau was more sensitive to temperature change. There was an evident sum-mer warming signal after 1983. Although the last 100-year running average of summer tem-perature in the 1990s was the maximum, the running average of the early 1990s was below the average line and it was cold summer, but summer drought occurred in the late 1990s.
Maximum confidence measurements via probabilistic quantum cloning
Zhang Wen-Hai; Yu Long-Bao; Cao Zhuo-Liang; Ye Liu
2013-01-01
Probabilistic quantum cloning (PQC) cannot copy a set of linearly dependent quantum states.In this paper,we show that if incorrect copies are allowed to be produced,linearly dependent quantum states may also be cloned by the PQC.By exploiting this kind of PQC to clone a special set of three linearly dependent quantum states,we derive the upper bound of the maximum confidence measure of a set.An explicit transformation of the maximum confidence measure is presented.
王跃; 翦知湣; 赵平
2011-01-01
利用美国国家大气研究中心的CAM 3大气环流模式,研究模拟了末次盛冰期热带辐合带(Intertropical Convergence Zone,简称ITCZ)/夏季风区降雨对热带表层海水温度(Sea Surface temperature,简称SST)变化的敏感性,结果发现:1)在冰期边界条件下热带SST异常很大程度上控制着局地降阿的响应,特别当SST异常范围从区域扩大到全球热带地区,ITCZ/夏季风降雨的剧烈变化可以与其他冰期边界条件的影响相当;2)不论是以古海洋重建的热带SST还是海气耦合模拟输出的SST为边界条件.CAM 3中热带降雨基本上与局地SST呈正相关关系(SST变暖.降雨增加),并同时受SST梯度分布格局控制.这与完全海气耦合模式的冰期模拟结果一致;3)合理的SST边界条件(特别是海气耦合模式输出的SST分布)驱动下,模拟得到的热带降雨异常分布与其他独立的占海洋水循环特征指标重建更为吻合(相对于现代值,亚洲夏季风区和赤道西太平洋辐合带降雨增加,两侧副热带太平洋降雨减少).这些结果不仅为探索未次盛冰期时期热带水循环特征变化提供了新的古海洋重建数据支撑,也有利于进一步揭示冰期/间冰期旋回中热带气候变化的物理机制所在.如该项研究揭示的热带SST-降雨正相关关系在赤道中东太平洋等非季风区与现代观测一致.而现代亚洲太平洋夏季风区中负相关关系在冰期条件下并未得到再现,说明不同气候背景对夏季风区海气相互作用有重要影响.%Modern observations have demonstrated two kinds of correlation between tropical Sea Surface Temperature ( SST) and local precipitation anomalies : negative in Asian-Pacific summer monsoon regions and positive in CentralEastern equatorial Pacific. Paleoclimatic studies have also revealed that different patterns of tropical SST could cause drastic changes of precipitation through tropical convections and atmospheric
Vestige: Maximum likelihood phylogenetic footprinting
Maxwell Peter
2005-05-01
Full Text Available Abstract Background Phylogenetic footprinting is the identification of functional regions of DNA by their evolutionary conservation. This is achieved by comparing orthologous regions from multiple species and identifying the DNA regions that have diverged less than neutral DNA. Vestige is a phylogenetic footprinting package built on the PyEvolve toolkit that uses probabilistic molecular evolutionary modelling to represent aspects of sequence evolution, including the conventional divergence measure employed by other footprinting approaches. In addition to measuring the divergence, Vestige allows the expansion of the definition of a phylogenetic footprint to include variation in the distribution of any molecular evolutionary processes. This is achieved by displaying the distribution of model parameters that represent partitions of molecular evolutionary substitutions. Examination of the spatial incidence of these effects across regions of the genome can identify DNA segments that differ in the nature of the evolutionary process. Results Vestige was applied to a reference dataset of the SCL locus from four species and provided clear identification of the known conserved regions in this dataset. To demonstrate the flexibility to use diverse models of molecular evolution and dissect the nature of the evolutionary process Vestige was used to footprint the Ka/Ks ratio in primate BRCA1 with a codon model of evolution. Two regions of putative adaptive evolution were identified illustrating the ability of Vestige to represent the spatial distribution of distinct molecular evolutionary processes. Conclusion Vestige provides a flexible, open platform for phylogenetic footprinting. Underpinned by the PyEvolve toolkit, Vestige provides a framework for visualising the signatures of evolutionary processes across the genome of numerous organisms simultaneously. By exploiting the maximum-likelihood statistical framework, the complex interplay between mutational
A stochastic maximum principle via Malliavin calculus
Øksendal, Bernt; Zhou, Xun Yu; Meyer-Brandis, Thilo
2008-01-01
This paper considers a controlled It\\^o-L\\'evy process where the information available to the controller is possibly less than the overall information. All the system coefficients and the objective performance functional are allowed to be random, possibly non-Markovian. Malliavin calculus is employed to derive a maximum principle for the optimal control of such a system where the adjoint process is explicitly expressed.
Allowable carbon emissions for medium-to-high mitigation scenarios
Tachiiri, Kaoru; Hargreaves, Julia C.; Annan, James D.; Kawamiya, Michio [Research Inst. for Global Change, Japan Agency for Marine-Earth Science and Technology, Yokohama, (Japan)], e-mail: tachiiri@jamstec.go.jp; Huntingford, Chris [Centre for Ecology and Hydrology, Wallingford (United Kingdom)
2013-11-15
source to the atmosphere, although uncertainties on this are large. The parameters which most significantly affect the allowable emissions are aerosols and climate sensitivity, but some carbon-cycle related parameters (e.g. maximum photosynthetic rate and respiration's temperature dependency of vegetation) also have significant effects. Parameter values are constrained by observation, and we found that the CO{sub 2} emission data had a significant effect in constraining climate sensitivity and the magnitude of aerosol radiative forcing.
Moacyr Jorge Elias
2011-04-01
Full Text Available Bromelain, the enzyme found in pineapple, hydrolyzes proteins’ peptide bonds, has several applications in the food industry and in medicine. Temperature and pH conditions for highest activity with casein as substrate were investigated from the bromelain recovered from industrialized pineapple (‘pérola’ variety fruit residues. Extract was obtained by grinding fruit rind and its internal stem. The activity was expressed in mmol tyrosine L-1 min. -1 by absorbance at 280 nm of aromatic amino acids produced in casein hydrolysis. Assays were undertaken in duplicate for two enzyme/substrate with ratios: 1/25 and 1/125 (mass. Eight-pointed experimental design was undertaken with central value for pH at 7.0 and for temperature at 35°C. Experimental results were processed by MINITAB 15 (Minitab Inc software which provided model’s equations and surface responses. Equations were mathematically processed by differential calculus producing graphs which exhibit the best activities according to temperatures. Loss of enzyme activity was reported with temperature increase at 1/25 ratio, due to a higher free enzyme, when compared to 1/125 ratio.
Mehdi Dehghan
2001-01-01
Full Text Available Two different finite difference schemes for solving the two-dimensional parabolic inverse problem with temperature overspecification are considered. These schemes are developed for indentifying the control parameter which produces, at any given time, a desired temperature distribution at a given point in the spatial domain. The numerical methods discussed, are based on the (3,3 alternating direction implicit (ADI finite difference scheme and the (3,9 alternating direction implicit formula. These schemes are unconditionally stable. The basis of analysis of the finite difference equation considered here is the modified equivalent partial differential equation approach, developed from the 1974 work of Warming and Hyett [17]. This allows direct and simple comparison of the errors associated with the equations as well as providing a means to develop more accurate finite difference schemes. These schemes use less central processor times than the fully implicit schemes for two-dimensional diffusion with temperature overspecification. The alternating direction implicit schemes developed in this report use more CPU times than the fully explicit finite difference schemes, but their unconditional stability is significant. The results of numerical experiments are presented, and accuracy and the Central Processor (CPU times needed for each of the methods are discussed. We also give error estimates in the maximum norm for each of these methods.
毛炜峄; 陈鹏翔; 沈永平
2016-01-01
用新疆105个气象站监测资料，分析了2015年夏季高温过程的极端特征.2015年夏季新疆区域出现高温过程，从7月上旬后期开始，南疆东南部以及东疆最早出现日最高气温≥35℃的高温天气，进入中旬后高温范围迅速向西、向北蔓延发展，下旬初期范围达最大，南北疆均出现高温天气.新疆区域该次高温过程在7月中下旬最为强盛，全疆84.8%的测站（89站）出现高温；52.4%的测站（55站）的高温持续日数位居历史第1位；全疆21.9%的测站（23站）极端最高气温位居历史第1位，极端最高气温出现在吐鲁番东坎，达到47.7℃.这次高温过程造成8站夏季温度位居同期第1位，南疆及天山山区的7月平均气温位居历史同期第1位，有54.3%的测站（57站）7月平均气温突破同期历史极值.海拔3544 m的天山山区大西沟站7月份日最高气温连续突破历史极值，22日达到20.7℃.高温过程中，新疆区域7月0℃层高度位居1991年以来同期第1位，其中，7月19-23日连续6 d位居1991年以来的第1位.天山开都河流域日0℃层高度持续33 d高于1991-2015年平均值.7月上旬到下旬，在500 hPa高空，伊朗高压东移并控制新疆，是造成此次高温过程的直接原因.在100 hPa高空，南亚高压的形态、中心位置、强度变化与新疆此次高温过程演变关系密切.高温过程造成新疆高山区冰雪迅速消融，引发塔里木河流域出现融雪（冰）型洪水.%Meteorological datasets from 105 meteorological stations in Xinjiang were utilized to analyze the char-acteristics of extreme maximum air temperature in the summer of 2015. The extreme maximum air temperature more than 35℃firstly occurred in early July in southeastern and eastern Xinjiang region,and then spread west-wards and northwestwards in mid-July. In the late July,the range of extreme maximum air temperature reached up to the top,both in northern
Vietnam recommended dietary allowances 2007.
Khan, Nguyen Cong; Hoan, Pham Van
2008-01-01
It has been well acknowledged that Vietnam is undergoing a nutrition transition. With a rapid change in the country's reform and economic growth, food supply at the macronutrient level has improved. Changes of the Vietnamese diet include significantly more foods of animal origin, and an increase of fat/oils, and ripe fruits. Consequently, nutritional problems in Vietnam now include not only malnutrition but also overweight/obesity, metabolic syndrome and other chronic diseases related to nutrition and lifestyles. The recognition of these shifts, which is also associated with morbidity and mortality, was a major factor in the need to review and update the Recommended Dietary Allowances (RDA) for the Vietnamese population. This revised RDA established an important science-based tool for evaluation of nutrition adequacy, for teaching, and for scientific communications within Vietnam. It is expected that the 2007 Vietnam RDA and its conversion to food-based dietary guidelines will facilitate education to the public, as well as the policy implementation of programs for prevention of non-communicable chronic diseases and addressing the double burden of both under and over nutrition.
Multiresolution maximum intensity volume rendering by morphological adjunction pyramids
Roerdink, Jos B.T.M.
We describe a multiresolution extension to maximum intensity projection (MIP) volume rendering, allowing progressive refinement and perfect reconstruction. The method makes use of morphological adjunction pyramids. The pyramidal analysis and synthesis operators are composed of morphological 3-D
Multiresolution Maximum Intensity Volume Rendering by Morphological Adjunction Pyramids
Roerdink, Jos B.T.M.
2001-01-01
We describe a multiresolution extension to maximum intensity projection (MIP) volume rendering, allowing progressive refinement and perfect reconstruction. The method makes use of morphological adjunction pyramids. The pyramidal analysis and synthesis operators are composed of morphological 3-D
OECD Maximum Residue Limit Calculator
With the goal of harmonizing the calculation of maximum residue limits (MRLs) across the Organisation for Economic Cooperation and Development, the OECD has developed an MRL Calculator. View the calculator.
Temperature initiated passive cooling system
Forsberg, Charles W.
1994-01-01
A passive cooling system for cooling an enclosure only when the enclosure temperature exceeds a maximum standby temperature comprises a passive heat transfer loop containing heat transfer fluid having a particular thermodynamic critical point temperature just above the maximum standby temperature. An upper portion of the heat transfer loop is insulated to prevent two phase operation below the maximum standby temperature.
Weak scale from the maximum entropy principle
Hamada, Yuta; Kawai, Hikaru; Kawana, Kiyoharu
2015-03-01
The theory of the multiverse and wormholes suggests that the parameters of the Standard Model (SM) are fixed in such a way that the radiation of the S3 universe at the final stage S_rad becomes maximum, which we call the maximum entropy principle. Although it is difficult to confirm this principle generally, for a few parameters of the SM, we can check whether S_rad actually becomes maximum at the observed values. In this paper, we regard S_rad at the final stage as a function of the weak scale (the Higgs expectation value) vh, and show that it becomes maximum around vh = {{O}} (300 GeV) when the dimensionless couplings in the SM, i.e., the Higgs self-coupling, the gauge couplings, and the Yukawa couplings are fixed. Roughly speaking, we find that the weak scale is given by vh ˜ T_{BBN}2 / (M_{pl}ye5), where ye is the Yukawa coupling of electron, T_BBN is the temperature at which the Big Bang nucleosynthesis starts, and M_pl is the Planck mass.
Pareto versus lognormal: a maximum entropy test.
Bee, Marco; Riccaboni, Massimo; Schiavo, Stefano
2011-08-01
It is commonly found that distributions that seem to be lognormal over a broad range change to a power-law (Pareto) distribution for the last few percentiles. The distributions of many physical, natural, and social events (earthquake size, species abundance, income and wealth, as well as file, city, and firm sizes) display this structure. We present a test for the occurrence of power-law tails in statistical distributions based on maximum entropy. This methodology allows one to identify the true data-generating processes even in the case when it is neither lognormal nor Pareto. The maximum entropy approach is then compared with other widely used methods and applied to different levels of aggregation of complex systems. Our results provide support for the theory that distributions with lognormal body and Pareto tail can be generated as mixtures of lognormally distributed units.
Nonparametric Maximum Entropy Estimation on Information Diagrams
Martin, Elliot A; Meinke, Alexander; Děchtěrenko, Filip; Davidsen, Jörn
2016-01-01
Maximum entropy estimation is of broad interest for inferring properties of systems across many different disciplines. In this work, we significantly extend a technique we previously introduced for estimating the maximum entropy of a set of random discrete variables when conditioning on bivariate mutual informations and univariate entropies. Specifically, we show how to apply the concept to continuous random variables and vastly expand the types of information-theoretic quantities one can condition on. This allows us to establish a number of significant advantages of our approach over existing ones. Not only does our method perform favorably in the undersampled regime, where existing methods fail, but it also can be dramatically less computationally expensive as the cardinality of the variables increases. In addition, we propose a nonparametric formulation of connected informations and give an illustrative example showing how this agrees with the existing parametric formulation in cases of interest. We furthe...
Maximum margin Bayesian network classifiers.
Pernkopf, Franz; Wohlmayr, Michael; Tschiatschek, Sebastian
2012-03-01
We present a maximum margin parameter learning algorithm for Bayesian network classifiers using a conjugate gradient (CG) method for optimization. In contrast to previous approaches, we maintain the normalization constraints on the parameters of the Bayesian network during optimization, i.e., the probabilistic interpretation of the model is not lost. This enables us to handle missing features in discriminatively optimized Bayesian networks. In experiments, we compare the classification performance of maximum margin parameter learning to conditional likelihood and maximum likelihood learning approaches. Discriminative parameter learning significantly outperforms generative maximum likelihood estimation for naive Bayes and tree augmented naive Bayes structures on all considered data sets. Furthermore, maximizing the margin dominates the conditional likelihood approach in terms of classification performance in most cases. We provide results for a recently proposed maximum margin optimization approach based on convex relaxation. While the classification results are highly similar, our CG-based optimization is computationally up to orders of magnitude faster. Margin-optimized Bayesian network classifiers achieve classification performance comparable to support vector machines (SVMs) using fewer parameters. Moreover, we show that unanticipated missing feature values during classification can be easily processed by discriminatively optimized Bayesian network classifiers, a case where discriminative classifiers usually require mechanisms to complete unknown feature values in the data first.
A Maximum Radius for Habitable Planets.
Alibert, Yann
2015-09-01
We compute the maximum radius a planet can have in order to fulfill two constraints that are likely necessary conditions for habitability: 1- surface temperature and pressure compatible with the existence of liquid water, and 2- no ice layer at the bottom of a putative global ocean, that would prevent the operation of the geologic carbon cycle to operate. We demonstrate that, above a given radius, these two constraints cannot be met: in the Super-Earth mass range (1-12 Mearth), the overall maximum that a planet can have varies between 1.8 and 2.3 Rearth. This radius is reduced when considering planets with higher Fe/Si ratios, and taking into account irradiation effects on the structure of the gas envelope.
Ludmila Bardin
2010-01-01
Full Text Available Desenvolveram-se, neste trabalho modelos de estimativa da temperatura do ar com base em fatores geográficos, visando estimar os valores máximos e mínimos médios mensais e anuais na região compreendida pelos municípios que compõem o Polo Turístico do Circuito das Frutas do Estado de São Paulo. Obtiveram-se equações de regressão múltipla em função da altitude, latitude e longitude e simples em função da altitude, cujos coeficientes de determinação variam entre 0,91 a 0,96, para as temperaturas máximas e 0,71 a 0,94 para as mínimas e se apresentam as variações espaciais das temperaturas máximas e mínimas médias mensais e anuais da região de estudo na forma de mapas.Multiple regression equations to estimate mean monthy and annual maximum and minimum temperatures were developed as a function of altitude, latitude, and longitude for the "Pólo Turístico do Circuito das Frutas" region. The obtained correlation coefficients varied from 0.91 to 0.96 and 0.71 to 0.94 of the maximum and minimum air temperature, respectively. Also, maps with the spacial variability of the maximum and minimum mean monthly and annual temperatures are presented for the region.
Maximum entropy signal restoration with linear programming
Mastin, G.A.; Hanson, R.J.
1988-05-01
Dantzig's bounded-variable method is used to express the maximum entropy restoration problem as a linear programming problem. This is done by approximating the nonlinear objective function with piecewise linear segments, then bounding the variables as a function of the number of segments used. The use of a linear programming approach allows equality constraints found in the traditional Lagrange multiplier method to be relaxed. A robust revised simplex algorithm is used to implement the restoration. Experimental results from 128- and 512-point signal restorations are presented.
Multi-Channel Maximum Likelihood Pitch Estimation
Christensen, Mads Græsbøll
2012-01-01
In this paper, a method for multi-channel pitch estimation is proposed. The method is a maximum likelihood estimator and is based on a parametric model where the signals in the various channels share the same fundamental frequency but can have different amplitudes, phases, and noise characteristics....... This essentially means that the model allows for different conditions in the various channels, like different signal-to-noise ratios, microphone characteristics and reverberation. Moreover, the method does not assume that a certain array structure is used but rather relies on a more general model and is hence...
CORA: Emission Line Fitting with Maximum Likelihood
Ness, Jan-Uwe; Wichmann, Rainer
2011-12-01
CORA analyzes emission line spectra with low count numbers and fits them to a line using the maximum likelihood technique. CORA uses a rigorous application of Poisson statistics. From the assumption of Poissonian noise, the software derives the probability for a model of the emission line spectrum to represent the measured spectrum. The likelihood function is used as a criterion for optimizing the parameters of the theoretical spectrum and a fixed point equation is derived allowing an efficient way to obtain line fluxes. CORA has been applied to an X-ray spectrum with the Low Energy Transmission Grating Spectrometer (LETGS) on board the Chandra observatory.
The sun and heliosphere at solar maximum.
Smith, E J; Marsden, R G; Balogh, A; Gloeckler, G; Geiss, J; McComas, D J; McKibben, R B; MacDowall, R J; Lanzerotti, L J; Krupp, N; Krueger, H; Landgraf, M
2003-11-14
Recent Ulysses observations from the Sun's equator to the poles reveal fundamental properties of the three-dimensional heliosphere at the maximum in solar activity. The heliospheric magnetic field originates from a magnetic dipole oriented nearly perpendicular to, instead of nearly parallel to, the Sun's rotation axis. Magnetic fields, solar wind, and energetic charged particles from low-latitude sources reach all latitudes, including the polar caps. The very fast high-latitude wind and polar coronal holes disappear and reappear together. Solar wind speed continues to be inversely correlated with coronal temperature. The cosmic ray flux is reduced symmetrically at all latitudes.
Abolishing the maximum tension principle
Dabrowski, Mariusz P
2015-01-01
We find the series of example theories for which the relativistic limit of maximum tension $F_{max} = c^2/4G$ represented by the entropic force can be abolished. Among them the varying constants theories, some generalized entropy models applied both for cosmological and black hole horizons as well as some generalized uncertainty principle models.
Abolishing the maximum tension principle
Mariusz P. Da̧browski
2015-09-01
Full Text Available We find the series of example theories for which the relativistic limit of maximum tension Fmax=c4/4G represented by the entropic force can be abolished. Among them the varying constants theories, some generalized entropy models applied both for cosmological and black hole horizons as well as some generalized uncertainty principle models.
Mechanical Sun-Tracking Technique Implemented for Maximum ...
The solar panel is allowed to move from east to west and back forth with a maximum allowable angle of 180o. Its movement is in only one axis. The prototype built carries the panel from eastward to westward tracking the sun movement from ...
The maximum rate of mammal evolution
Evans, Alistair R.; Jones, David; Boyer, Alison G.; Brown, James H.; Costa, Daniel P.; Ernest, S. K. Morgan; Fitzgerald, Erich M. G.; Fortelius, Mikael; Gittleman, John L.; Hamilton, Marcus J.; Harding, Larisa E.; Lintulaakso, Kari; Lyons, S. Kathleen; Okie, Jordan G.; Saarinen, Juha J.; Sibly, Richard M.; Smith, Felisa A.; Stephens, Patrick R.; Theodor, Jessica M.; Uhen, Mark D.
2012-03-01
How fast can a mammal evolve from the size of a mouse to the size of an elephant? Achieving such a large transformation calls for major biological reorganization. Thus, the speed at which this occurs has important implications for extensive faunal changes, including adaptive radiations and recovery from mass extinctions. To quantify the pace of large-scale evolution we developed a metric, clade maximum rate, which represents the maximum evolutionary rate of a trait within a clade. We applied this metric to body mass evolution in mammals over the last 70 million years, during which multiple large evolutionary transitions occurred in oceans and on continents and islands. Our computations suggest that it took a minimum of 1.6, 5.1, and 10 million generations for terrestrial mammal mass to increase 100-, and 1,000-, and 5,000-fold, respectively. Values for whales were down to half the length (i.e., 1.1, 3, and 5 million generations), perhaps due to the reduced mechanical constraints of living in an aquatic environment. When differences in generation time are considered, we find an exponential increase in maximum mammal body mass during the 35 million years following the Cretaceous-Paleogene (K-Pg) extinction event. Our results also indicate a basic asymmetry in macroevolution: very large decreases (such as extreme insular dwarfism) can happen at more than 10 times the rate of increases. Our findings allow more rigorous comparisons of microevolutionary and macroevolutionary patterns and processes.
Minimal Length, Friedmann Equations and Maximum Density
Awad, Adel
2014-01-01
Inspired by Jacobson's thermodynamic approach[gr-qc/9504004], Cai et al [hep-th/0501055,hep-th/0609128] have shown the emergence of Friedmann equations from the first law of thermodynamics. We extend Akbar--Cai derivation [hep-th/0609128] of Friedmann equations to accommodate a general entropy-area law. Studying the resulted Friedmann equations using a specific entropy-area law, which is motivated by the generalized uncertainty principle (GUP), reveals the existence of a maximum energy density closed to Planck density. Allowing for a general continuous pressure $p(\\rho,a)$ leads to bounded curvature invariants and a general nonsingular evolution. In this case, the maximum energy density is reached in a finite time and there is no cosmological evolution beyond this point which leaves the big bang singularity inaccessible from a spacetime prospective. The existence of maximum energy density and a general nonsingular evolution is independent of the equation of state and the spacial curvature $k$. As an example w...
The maximum rate of mammal evolution
Evans, Alistair R.; Jones, David; Boyer, Alison G.; Brown, James H.; Costa, Daniel P.; Ernest, S. K. Morgan; Fitzgerald, Erich M. G.; Fortelius, Mikael; Gittleman, John L.; Hamilton, Marcus J.; Harding, Larisa E.; Lintulaakso, Kari; Lyons, S. Kathleen; Okie, Jordan G.; Saarinen, Juha J.; Sibly, Richard M.; Smith, Felisa A.; Stephens, Patrick R.; Theodor, Jessica M.; Uhen, Mark D.
2012-01-01
How fast can a mammal evolve from the size of a mouse to the size of an elephant? Achieving such a large transformation calls for major biological reorganization. Thus, the speed at which this occurs has important implications for extensive faunal changes, including adaptive radiations and recovery from mass extinctions. To quantify the pace of large-scale evolution we developed a metric, clade maximum rate, which represents the maximum evolutionary rate of a trait within a clade. We applied this metric to body mass evolution in mammals over the last 70 million years, during which multiple large evolutionary transitions occurred in oceans and on continents and islands. Our computations suggest that it took a minimum of 1.6, 5.1, and 10 million generations for terrestrial mammal mass to increase 100-, and 1,000-, and 5,000-fold, respectively. Values for whales were down to half the length (i.e., 1.1, 3, and 5 million generations), perhaps due to the reduced mechanical constraints of living in an aquatic environment. When differences in generation time are considered, we find an exponential increase in maximum mammal body mass during the 35 million years following the Cretaceous–Paleogene (K–Pg) extinction event. Our results also indicate a basic asymmetry in macroevolution: very large decreases (such as extreme insular dwarfism) can happen at more than 10 times the rate of increases. Our findings allow more rigorous comparisons of microevolutionary and macroevolutionary patterns and processes. PMID:22308461
The maximum rate of mammal evolution.
Evans, Alistair R; Jones, David; Boyer, Alison G; Brown, James H; Costa, Daniel P; Ernest, S K Morgan; Fitzgerald, Erich M G; Fortelius, Mikael; Gittleman, John L; Hamilton, Marcus J; Harding, Larisa E; Lintulaakso, Kari; Lyons, S Kathleen; Okie, Jordan G; Saarinen, Juha J; Sibly, Richard M; Smith, Felisa A; Stephens, Patrick R; Theodor, Jessica M; Uhen, Mark D
2012-03-13
How fast can a mammal evolve from the size of a mouse to the size of an elephant? Achieving such a large transformation calls for major biological reorganization. Thus, the speed at which this occurs has important implications for extensive faunal changes, including adaptive radiations and recovery from mass extinctions. To quantify the pace of large-scale evolution we developed a metric, clade maximum rate, which represents the maximum evolutionary rate of a trait within a clade. We applied this metric to body mass evolution in mammals over the last 70 million years, during which multiple large evolutionary transitions occurred in oceans and on continents and islands. Our computations suggest that it took a minimum of 1.6, 5.1, and 10 million generations for terrestrial mammal mass to increase 100-, and 1,000-, and 5,000-fold, respectively. Values for whales were down to half the length (i.e., 1.1, 3, and 5 million generations), perhaps due to the reduced mechanical constraints of living in an aquatic environment. When differences in generation time are considered, we find an exponential increase in maximum mammal body mass during the 35 million years following the Cretaceous-Paleogene (K-Pg) extinction event. Our results also indicate a basic asymmetry in macroevolution: very large decreases (such as extreme insular dwarfism) can happen at more than 10 times the rate of increases. Our findings allow more rigorous comparisons of microevolutionary and macroevolutionary patterns and processes.
Maximum Spectral Luminous Efficacy of White Light
Murphy, T W
2013-01-01
As lighting efficiency improves, it is useful to understand the theoretical limits to luminous efficacy for light that we perceive as white. Independent of the efficiency with which photons are generated, there exists a spectrally-imposed limit to the luminous efficacy of any source of photons. We find that, depending on the acceptable bandpass and---to a lesser extent---the color temperature of the light, the ideal white light source achieves a spectral luminous efficacy of 250--370 lm/W. This is consistent with previous calculations, but here we explore the maximum luminous efficacy as a function of photopic sensitivity threshold, color temperature, and color rendering index; deriving peak performance as a function of all three parameters. We also present example experimental spectra from a variety of light sources, quantifying the intrinsic efficacy of their spectral distributions.
Maximum Genus of Strong Embeddings
Er-ling Wei; Yan-pei Liu; Han Ren
2003-01-01
The strong embedding conjecture states that any 2-connected graph has a strong embedding on some surface. It implies the circuit double cover conjecture: Any 2-connected graph has a circuit double cover.Conversely, it is not true. But for a 3-regular graph, the two conjectures are equivalent. In this paper, a characterization of graphs having a strong embedding with exactly 3 faces, which is the strong embedding of maximum genus, is given. In addition, some graphs with the property are provided. More generally, an upper bound of the maximum genus of strong embeddings of a graph is presented too. Lastly, it is shown that the interpolation theorem is true to planar Halin graph.
Remizov, Ivan D
2009-01-01
In this note, we represent a subdifferential of a maximum functional defined on the space of all real-valued continuous functions on a given metric compact set. For a given argument, $f$ it coincides with the set of all probability measures on the set of points maximizing $f$ on the initial compact set. This complete characterization lies in the heart of several important identities in microeconomics, such as Roy's identity, Sheppard's lemma, as well as duality theory in production and linear programming.
The Testability of Maximum Magnitude
Clements, R.; Schorlemmer, D.; Gonzalez, A.; Zoeller, G.; Schneider, M.
2012-12-01
Recent disasters caused by earthquakes of unexpectedly large magnitude (such as Tohoku) illustrate the need for reliable assessments of the seismic hazard. Estimates of the maximum possible magnitude M at a given fault or in a particular zone are essential parameters in probabilistic seismic hazard assessment (PSHA), but their accuracy remains untested. In this study, we discuss the testability of long-term and short-term M estimates and the limitations that arise from testing such rare events. Of considerable importance is whether or not those limitations imply a lack of testability of a useful maximum magnitude estimate, and whether this should have any influence on current PSHA methodology. We use a simple extreme value theory approach to derive a probability distribution for the expected maximum magnitude in a future time interval, and we perform a sensitivity analysis on this distribution to determine if there is a reasonable avenue available for testing M estimates as they are commonly reported today: devoid of an appropriate probability distribution of their own and estimated only for infinite time (or relatively large untestable periods). Our results imply that any attempt at testing such estimates is futile, and that the distribution is highly sensitive to M estimates only under certain optimal conditions that are rarely observed in practice. In the future we suggest that PSHA modelers be brutally honest about the uncertainty of M estimates, or must find a way to decrease its influence on the estimated hazard.
Alternative Multiview Maximum Entropy Discrimination.
Chao, Guoqing; Sun, Shiliang
2016-07-01
Maximum entropy discrimination (MED) is a general framework for discriminative estimation based on maximum entropy and maximum margin principles, and can produce hard-margin support vector machines under some assumptions. Recently, the multiview version of MED multiview MED (MVMED) was proposed. In this paper, we try to explore a more natural MVMED framework by assuming two separate distributions p1( Θ1) over the first-view classifier parameter Θ1 and p2( Θ2) over the second-view classifier parameter Θ2 . We name the new MVMED framework as alternative MVMED (AMVMED), which enforces the posteriors of two view margins to be equal. The proposed AMVMED is more flexible than the existing MVMED, because compared with MVMED, which optimizes one relative entropy, AMVMED assigns one relative entropy term to each of the two views, thus incorporating a tradeoff between the two views. We give the detailed solving procedure, which can be divided into two steps. The first step is solving our optimization problem without considering the equal margin posteriors from two views, and then, in the second step, we consider the equal posteriors. Experimental results on multiple real-world data sets verify the effectiveness of the AMVMED, and comparisons with MVMED are also reported.
Assessing allowable take of migratory birds
Runge, M.C.; Sauer, J.R.; Avery, M.L.; Blackwell, B.F.; Koneff, M.D.
2009-01-01
Legal removal of migratory birds from the wild occurs for several reasons, including subsistence, sport harvest, damage control, and the pet trade. We argue that harvest theory provides the basis for assessing the impact of authorized take, advance a simplified rendering of harvest theory known as potential biological removal as a useful starting point for assessing take, and demonstrate this approach with a case study of depredation control of black vultures (Coragyps atratus) in Virginia, USA. Based on data from the North American Breeding Bird Survey and other sources, we estimated that the black vulture population in Virginia was 91,190 (95% credible interval = 44,520?212,100) in 2006. Using a simple population model and available estimates of life-history parameters, we estimated the intrinsic rate of growth (rmax) to be in the range 7?14%, with 10.6% a plausible point estimate. For a take program to seek an equilibrium population size on the conservative side of the yield curve, the rate of take needs to be less than that which achieves a maximum sustained yield (0.5 x rmax). Based on the point estimate for rmax and using the lower 60% credible interval for population size to account for uncertainty, these conditions would be met if the take of black vultures in Virginia in 2006 was <3,533 birds. Based on regular monitoring data, allowable harvest should be adjusted annually to reflect changes in population size. To initiate discussion about how this assessment framework could be related to the laws and regulations that govern authorization of such take, we suggest that the Migratory Bird Treaty Act requires only that take of native migratory birds be sustainable in the long-term, that is, sustained harvest rate should be
Midnight Temperature Maximum (MTM) in Whole Atmosphere Model (WAM) Simulations
2016-04-14
typical magnitudes of 50–100 K has been regularly observed by satellite and ground-based instruments in the tropical upper thermosphere. Although...the feature with typical magnitudes of about 50–100 K around midnight [e.g., Faivre et al., 2006]. Recent observations of a night- glow brightness wave...different UT-longitude sectors. A prominent MTM with a magnitude between about 50 K and well over 100 K clearly stands out at both locations and
Cacti with maximum Kirchhoff index
Wang, Wen-Rui; Pan, Xiang-Feng
2015-01-01
The concept of resistance distance was first proposed by Klein and Randi\\'c. The Kirchhoff index $Kf(G)$ of a graph $G$ is the sum of resistance distance between all pairs of vertices in $G$. A connected graph $G$ is called a cactus if each block of $G$ is either an edge or a cycle. Let $Cat(n;t)$ be the set of connected cacti possessing $n$ vertices and $t$ cycles, where $0\\leq t \\leq \\lfloor\\frac{n-1}{2}\\rfloor$. In this paper, the maximum kirchhoff index of cacti are characterized, as well...
Generic maximum likely scale selection
Pedersen, Kim Steenstrup; Loog, Marco; Markussen, Bo
2007-01-01
The fundamental problem of local scale selection is addressed by means of a novel principle, which is based on maximum likelihood estimation. The principle is generally applicable to a broad variety of image models and descriptors, and provides a generic scale estimation methodology. The focus...... on second order moments of multiple measurements outputs at a fixed location. These measurements, which reflect local image structure, consist in the cases considered here of Gaussian derivatives taken at several scales and/or having different derivative orders....
46 CFR 154.421 - Allowable stress.
2010-10-01
... 46 Shipping 5 2010-10-01 2010-10-01 false Allowable stress. 154.421 Section 154.421 Shipping COAST... § 154.421 Allowable stress. The allowable stress for the integral tank structure must meet the American Bureau of Shipping's allowable stress for the vessel's hull published in “Rules for Building and Classing...
46 CFR 154.440 - Allowable stress.
2010-10-01
... 46 Shipping 5 2010-10-01 2010-10-01 false Allowable stress. 154.440 Section 154.440 Shipping COAST... Tank Type A § 154.440 Allowable stress. (a) The allowable stresses for an independent tank type A must... Commandant (CG-522). (b) A greater allowable stress than required in paragraph (a)(1) of this section may be...
Alberto Cargnelutti Filho
2008-12-01
Full Text Available A partir dos dados referentes à temperatura máxima média decendial (Tx e à temperatura média decendial (Tm do ar de 41 municípios do Estado do Rio Grande do Sul, de 1945 a 1974, este trabalho teve como objetivo verificar se a Tx e a Tm podem ser estimadas em função da altitude, latitude e longitude. Para cada um dos 36 decêndios do ano, realizou-se análise de correlação e estimaram-se os parâmetros do modelo das equações de regressão linear múltipla, considerando Tx e Tm como variável dependente e altitude, latitude e longitude como variáveis independentes. Na validação dos modelos de estimativa da Tx e Tm, usou-se o coeficiente de correlação linear de Pearson, entre a Tx e a Tm estimada e a Tx e a Tm observada em dez municípios do Estado, com dados da série de observações meteorológicas de 1975 a 2004. A temperatura máxima média decendial e a temperatura média decendial podem ser estimadas por meio da altitude, latitude e longitude, em qualquer local e decêndio, no Estado do Rio Grande do Sul.The objective of this research was to estimate ten-day maximum (Tx and mean (Tm air temperature using altitude and the geographic coordinates latitude and longitude for the Rio Grande do Sul State, Brazil. Normal ten-day maximum and mean air temperature of 41 counties in the State of Rio Grande do Sul, from 1945 to 1974 were used. Correlation analysis and parameters estimate of multiple linear regression equations were performed using Tx and Tm as dependent variable and altitude, latitude and longitude as independent variables, for the 36 ten-day periods of the year. Pearson's linear correlation coefficient between estimated and observed Tx and Tm, calculated for tem counties using data of were used as independent data sets. The ten-day maximum and mean air temperature may be estimated from the altitude and the geographic coordinates latitude and longitude in the State of Rio Grande do Sul.
Understanding Peripheral Bat Populations Using Maximum-Entropy Suitability Modeling
Barnhart, Paul R.; Gillam, Erin H.
2016-01-01
Individuals along the periphery of a species distribution regularly encounter more challenging environmental and climatic conditions than conspecifics near the center of the distribution. Due to these potential constraints, individuals in peripheral margins are expected to change their habitat and behavioral characteristics. Managers typically rely on species distribution maps when developing adequate management practices. However, these range maps are often too simplistic and do not provide adequate information as to what fine-scale biotic and abiotic factors are driving a species occurrence. In the last decade, habitat suitability modelling has become widely used as a substitute for simplistic distribution mapping which allows regional managers the ability to fine-tune management resources. The objectives of this study were to use maximum-entropy modeling to produce habitat suitability models for seven species that have a peripheral margin intersecting the state of North Dakota, according to current IUCN distributions, and determine the vegetative and climatic characteristics driving these models. Mistnetting resulted in the documentation of five species outside the IUCN distribution in North Dakota, indicating that current range maps for North Dakota, and potentially the northern Great Plains, are in need of update. Maximum-entropy modeling showed that temperature and not precipitation were the variables most important for model production. This fine-scale result highlights the importance of habitat suitability modelling as this information cannot be extracted from distribution maps. Our results provide baseline information needed for future research about how and why individuals residing in the peripheral margins of a species’ distribution may show marked differences in habitat use as a result of urban expansion, habitat loss, and climate change compared to more centralized populations. PMID:27935936
张同文; 刘禹; 袁玉江; 魏文寿; 喻树龙; 陈峰
2011-01-01
for de-trending. After all the processes,we obtained three kinds of chronologies( STD, RES and ARS)of tree-ring width data and gray values.Based on the tree-ring data analysis, mean maximum temperature from May to August of the Gongnaisi region from 1777 to 2008 A. D. Has been reconstructed by the tree-ring average gray values. For the calibrated period (1958 ~ 2008 A. D. ) ,the predictor variable accounts for 39% of the variance of mean maximum temperature data. The mean maximum temperature reconstruction shows that there are 34 warm years and 38 cold years. The warm events (lasting for more than three years)were 1861 ~ 1864 A. D., 1873 ~ 1876A. D. And 1917 ~ 1919A. D. ; and the cold events were 1816 ~ 1818A. D., 1948 ~ 1950A. D. And 1957 - 1959A. D. Furthermore, these years and events correspond well with historical documents. By applying a 11-year moving average to our reconstruction, only one period with above average reconstructed mean maximum temperature (1777 ~ 2008A. D. ) comprise 1845 ~ 1925A. D. ; the two periods below average consist of 1788 ~ 1844A. D. And 1926~2001 A. D. The reconstructed mean maximum temperature has increased since the 1990s and agreed well with instrumental measurements in the North Western China in the recent 50 years. The power spectrum analysis shows that there are 154-,77-,2. 7- and 2. 3-years cycles in our reconstruction, which may be associated with solar activity and quasi-biennial oscillation ( QBO). The moving t-test indicates that the significant abrupt changes were presented in about 1842A. D., 1880A. D. And 1923A. D. The significant correlations between our reconstruction and the gridded dataset of the Northern Hemisphere and three kinds of index (SOI, APOI, and AOI) may imply that mean maximum temperature of the Gongnaisi region is possibly influenced not only by local,but also by multiple large-scale climate changes to some extent.
Regina C. de M. Pires
2004-12-01
Full Text Available A temperatura do solo é um importante parâmetro no cultivo do morangueiro, pois interfere no desenvolvimento vegetativo, na sanidade e na produção. O objetivo do presente trabalho foi avaliar o efeito de diferentes níveis de água, coberturas de canteiro em campo aberto e em ambiente protegido, na temperatura máxima do solo no cultivo do morangueiro. Foram realizados dois experimentos: um em cultivo protegido e outro a campo aberto, em Atibaia - SP, em esquema fatorial 2 x 3 (coberturas do solo e níveis de irrigação, em blocos ao acaso, com cinco repetições. As coberturas de solo utilizadas foram filmes de polietileno preto e transparente. A irrigação localizada foi aplicada por gotejo sempre que o potencial de água no solo atingisse -0,010 (N1, -0,035 (N2 e -0,070 (N3 MPa, em tensiômetros instalados a 10 cm de profundidade. A temperatura do solo foi avaliada por termógrafos, sendo os sensores instalados a 5 cm de profundidade. Houve influência do ambiente de cultivo, da cobertura do solo e dos níveis de irrigação na temperatura máxima do solo. A temperatura do solo sob diferentes coberturas dependeu não somente das características físicas do plástico, como também da forma de instalação no canteiro. A temperatura máxima do solo aumentou com a diminuição do potencial da água no solo, no momento da irrigação.The soil temperature is an important parameter in strawberry crop, because, it interferes in vegetative development, plant health conditions and yield. The aim of this work was to evaluate the effect of different water levels, soil covers in field conditions and greenhouse in maximum soil temperature in strawberry crop. Two experiments were accomplished, one in greenhouse and other in field conditions, at Atibaia - SP, Brazil. The experimental design was a factorial 2 x 3 (soil covers and water levels, with 5 repetitions. The soil covers were clear and black plastics. The trickle irrigation was applied
Objects of maximum electromagnetic chirality
Fernandez-Corbaton, Ivan
2015-01-01
We introduce a definition of the electromagnetic chirality of an object and show that it has an upper bound. The upper bound is attained if and only if the object is transparent for fields of one handedness (helicity). Additionally, electromagnetic duality symmetry, i.e. helicity preservation upon scattering, turns out to be a necessary condition for reciprocal scatterers to attain the upper bound. We use these results to provide requirements for the design of such extremal scatterers. The requirements can be formulated as constraints on the polarizability tensors for dipolar scatterers or as material constitutive relations. We also outline two applications for objects of maximum electromagnetic chirality: A twofold resonantly enhanced and background free circular dichroism measurement setup, and angle independent helicity filtering glasses.
Maximum mutual information regularized classification
Wang, Jim Jing-Yan
2014-09-07
In this paper, a novel pattern classification approach is proposed by regularizing the classifier learning to maximize mutual information between the classification response and the true class label. We argue that, with the learned classifier, the uncertainty of the true class label of a data sample should be reduced by knowing its classification response as much as possible. The reduced uncertainty is measured by the mutual information between the classification response and the true class label. To this end, when learning a linear classifier, we propose to maximize the mutual information between classification responses and true class labels of training samples, besides minimizing the classification error and reducing the classifier complexity. An objective function is constructed by modeling mutual information with entropy estimation, and it is optimized by a gradient descend method in an iterative algorithm. Experiments on two real world pattern classification problems show the significant improvements achieved by maximum mutual information regularization.
The strong maximum principle revisited
Pucci, Patrizia; Serrin, James
In this paper we first present the classical maximum principle due to E. Hopf, together with an extended commentary and discussion of Hopf's paper. We emphasize the comparison technique invented by Hopf to prove this principle, which has since become a main mathematical tool for the study of second order elliptic partial differential equations and has generated an enormous number of important applications. While Hopf's principle is generally understood to apply to linear equations, it is in fact also crucial in nonlinear theories, such as those under consideration here. In particular, we shall treat and discuss recent generalizations of the strong maximum principle, and also the compact support principle, for the case of singular quasilinear elliptic differential inequalities, under generally weak assumptions on the quasilinear operators and the nonlinearities involved. Our principal interest is in necessary and sufficient conditions for the validity of both principles; in exposing and simplifying earlier proofs of corresponding results; and in extending the conclusions to wider classes of singular operators than previously considered. The results have unexpected ramifications for other problems, as will develop from the exposition, e.g. two point boundary value problems for singular quasilinear ordinary differential equations (Sections 3 and 4); the exterior Dirichlet boundary value problem (Section 5); the existence of dead cores and compact support solutions, i.e. dead cores at infinity (Section 7); Euler-Lagrange inequalities on a Riemannian manifold (Section 9); comparison and uniqueness theorems for solutions of singular quasilinear differential inequalities (Section 10). The case of p-regular elliptic inequalities is briefly considered in Section 11.
Maximum entropy production and the fluctuation theorem
Dewar, R C [Unite EPHYSE, INRA Centre de Bordeaux-Aquitaine, BP 81, 33883 Villenave d' Ornon Cedex (France)
2005-05-27
Recently the author used an information theoretical formulation of non-equilibrium statistical mechanics (MaxEnt) to derive the fluctuation theorem (FT) concerning the probability of second law violating phase-space paths. A less rigorous argument leading to the variational principle of maximum entropy production (MEP) was also given. Here a more rigorous and general mathematical derivation of MEP from MaxEnt is presented, and the relationship between MEP and the FT is thereby clarified. Specifically, it is shown that the FT allows a general orthogonality property of maximum information entropy to be extended to entropy production itself, from which MEP then follows. The new derivation highlights MEP and the FT as generic properties of MaxEnt probability distributions involving anti-symmetric constraints, independently of any physical interpretation. Physically, MEP applies to the entropy production of those macroscopic fluxes that are free to vary under the imposed constraints, and corresponds to selection of the most probable macroscopic flux configuration. In special cases MaxEnt also leads to various upper bound transport principles. The relationship between MaxEnt and previous theories of irreversible processes due to Onsager, Prigogine and Ziegler is also clarified in the light of these results. (letter to the editor)
邓自刚; 王家素; 郑珺; 刘伟; 林群煦; 马光同; 王为; 王素玉; 张娅
2009-01-01
文章通过对15块高温超导块材与永磁轨道相互作用的悬浮力测试,比较了零场冷和场冷两种冷却方式下块材的最大悬浮力关系.实验结果显示零场冷时悬浮力大的块材在场冷时悬浮力不一定就大,反之亦然,两者并无直接的对应关系.在实际的场冷应用中,推荐以场冷下的悬浮力数据为参考.%The paper compares the relationship of maximum levitation force of bulk high temperature superconductor in zero-field-cooling (ZFC) and field-cooling (FC) cases by the levitation measurement of 15 bulks interacting with permanent magnet guideway. The experimental results show that the maximum forces in the two cooling cases are not corresponding to each other. The bulk with large levitation force in ZFC case will not always obtain a large one in the FC case, and vice ver-sa. So, the levitation force data in FC case is recommended to the practical FC applications.
Clean Air Markets - Allowances Query Wizard
U.S. Environmental Protection Agency — The Allowances Query Wizard is part of a suite of Clean Air Markets-related tools that are accessible at http://camddataandmaps.epa.gov/gdm/index.cfm. The Allowances...
Allowance Holdings and Transfers Data Inventory
U.S. Environmental Protection Agency — The Allowance Holdings and Transfers Data Inventory contains measured data on holdings and transactions of allowances under the NOx Budget Trading Program (NBP), a...
Maximum measurement range and accuracy of SAW reflective delay line sensors.
Zheng, Zehua; Han, Tao; Qin, Peng
2015-10-20
In a surface acoustic wave (SAW) wireless sensor with a reflective delay line structure, three reflectors are often used to eliminate 2π ambiguity of phase measurement. The maximum range of the measured parameter and the maximum accuracy have recently been attracting much research attention. In this paper, an analytical formula for all the factors influencing the measurement range and accuracy of the delay line SAW sensor are deduced for the first time. The factors include: the sensor sensitivity, the topology of the delay line, the available wireless bandwidth and the allowed maximum phase measuring error of the reading system, which is easier to retrieve and more fully describes the possible noises than SNR. Additionally, many designers believe that increasing the reflector could improve accuracy continuously or realize multi-resolution measurement. However, they ignore some certain criteria that the reflector location must satisfy. The reachable maximum accuracy by every increase of a reflector is also presented. A SAW temperature sensor system using 128° YX-LiNbO3 is designed to verify the above theoretical analysis.
Maximum Measurement Range and Accuracy of SAW Reflective Delay Line Sensors
Zehua Zheng
2015-10-01
Full Text Available In a surface acoustic wave (SAW wireless sensor with a reflective delay line structure, three reflectors are often used to eliminate 2π ambiguity of phase measurement. The maximum range of the measured parameter and the maximum accuracy have recently been attracting much research attention. In this paper, an analytical formula for all the factors influencing the measurement range and accuracy of the delay line SAW sensor are deduced for the first time. The factors include: the sensor sensitivity, the topology of the delay line, the available wireless bandwidth and the allowed maximum phase measuring error of the reading system, which is easier to retrieve and more fully describes the possible noises than SNR. Additionally, many designers believe that increasing the reflector could improve accuracy continuously or realize multi-resolution measurement. However, they ignore some certain criteria that the reflector location must satisfy. The reachable maximum accuracy by every increase of a reflector is also presented. A SAW temperature sensor system using 128° YX-LiNbO3 is designed to verify the above theoretical analysis.
Beat the Deviations in Estimating Maximum Power of Thermoelectric Modules
Gao, Junling; Chen, Min
2013-01-01
Under a certain temperature difference, the maximum power of a thermoelectric module can be estimated by the open-circuit voltage and the short-circuit current. In practical measurement, there exist two switch modes, either from open to short or from short to open, but the two modes can give...... different estimations on the maximum power. Using TEG-127-2.8-3.5-250 and TEG-127-1.4-1.6-250 as two examples, the difference is about 10%, leading to some deviations with the temperature change. This paper analyzes such differences by means of a nonlinear numerical model of thermoelectricity, and finds out...
46 CFR 154.428 - Allowable stress.
2010-10-01
... 46 Shipping 5 2010-10-01 2010-10-01 false Allowable stress. 154.428 Section 154.428 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS FOR... § 154.428 Allowable stress. The membrane tank and the supporting insulation must have allowable stresses...
46 CFR 154.447 - Allowable stress.
2010-10-01
... 46 Shipping 5 2010-10-01 2010-10-01 false Allowable stress. 154.447 Section 154.447 Shipping COAST... Tank Type B § 154.447 Allowable stress. (a) An independent tank type B designed from bodies of revolution must have allowable stresses 3 determined by the following formulae: 3 See Appendix B for stress...
Maximum stellar iron core mass
F W Giacobbe
2003-03-01
An analytical method of estimating the mass of a stellar iron core, just prior to core collapse, is described in this paper. The method employed depends, in part, upon an estimate of the true relativistic mass increase experienced by electrons within a highly compressed iron core, just prior to core collapse, and is signiﬁcantly different from a more typical Chandrasekhar mass limit approach. This technique produced a maximum stellar iron core mass value of 2.69 × 1030 kg (1.35 solar masses). This mass value is very near to the typical mass values found for neutron stars in a recent survey of actual neutron star masses. Although slightly lower and higher neutron star masses may also be found, lower mass neutron stars are believed to be formed as a result of enhanced iron core compression due to the weight of non-ferrous matter overlying the iron cores within large stars. And, higher mass neutron stars are likely to be formed as a result of fallback or accretion of additional matter after an initial collapse event involving an iron core having a mass no greater than 2.69 × 1030 kg.
Maximum Matchings via Glauber Dynamics
Jindal, Anant; Pal, Manjish
2011-01-01
In this paper we study the classic problem of computing a maximum cardinality matching in general graphs $G = (V, E)$. The best known algorithm for this problem till date runs in $O(m \\sqrt{n})$ time due to Micali and Vazirani \\cite{MV80}. Even for general bipartite graphs this is the best known running time (the algorithm of Karp and Hopcroft \\cite{HK73} also achieves this bound). For regular bipartite graphs one can achieve an $O(m)$ time algorithm which, following a series of papers, has been recently improved to $O(n \\log n)$ by Goel, Kapralov and Khanna (STOC 2010) \\cite{GKK10}. In this paper we present a randomized algorithm based on the Markov Chain Monte Carlo paradigm which runs in $O(m \\log^2 n)$ time, thereby obtaining a significant improvement over \\cite{MV80}. We use a Markov chain similar to the \\emph{hard-core model} for Glauber Dynamics with \\emph{fugacity} parameter $\\lambda$, which is used to sample independent sets in a graph from the Gibbs Distribution \\cite{V99}, to design a faster algori...
temperature distribution in underground cable system
Rerak Monika
2017-01-01
Full Text Available The paper presents a mathematical model of heat transfer in the underground cable system. The computations were performed for flat formation of power cables buried in the ground at a depth of 2 meters. The model allows determining the two-dimensional temperature distribution in the soil, thermal backfill and power cables. The simulations studied the effect of soil thermal conductivity on the maximum temperature of the cable conductor. Furthermore, the effect of thermal backfill soil conductivity on the cable conductor temperature was studied. Numerical analyses were performed based on a program written in MATLAB.
The maximum power efficiency 1-√τ: Research, education, and bibliometric relevance
Calvo Hernández, A.; Roco, J. M. M.; Medina, A.; Velasco, S.; Guzmán-Vargas, L.
2015-07-01
The well-known efficiency at maximum power for a cyclic system working between hot T h and low T c temperatures given by the equation 1-√ τ( τ= T c /T h), has become a landmark result with regards to the thermodynamic optimization of a great variety of energy converters. Its wide applicability and sole dependence on the external heat bath temperatures (as the Carnot efficiency does) allows for an easy comparison with experimental efficiencies leading to a striking fair agreement. Reversible, finite-time, and linear-irreversible derivations are analyzed in order to show a broader perspective about its meaning from both researching and pedagogical point of views. Its scientific relevance and historical development are also analyzed in this work by means of some bibliometric data. This article is supplemented with comments by Hong Qian and a final reply by the authors.
Incompatibility between Zircaloy-2 and Inconel X-750 during Temperature Transients
Warren, M. R.; Rørbo, Kaj; Adolph, Eivind
1975-01-01
The incompatibility of Zircaloy-2 and Inconel X-750 has been investigated between 1000°C and 1200°C (1200°C being the currently allowable maximum temperature in the acceptance criteria for ECCS for water reactors). It has been found for the temperatures of 1000°C and 1200°C that oxide thicknesses...
The Sherpa Maximum Likelihood Estimator
Nguyen, D.; Doe, S.; Evans, I.; Hain, R.; Primini, F.
2011-07-01
A primary goal for the second release of the Chandra Source Catalog (CSC) is to include X-ray sources with as few as 5 photon counts detected in stacked observations of the same field, while maintaining acceptable detection efficiency and false source rates. Aggressive source detection methods will result in detection of many false positive source candidates. Candidate detections will then be sent to a new tool, the Maximum Likelihood Estimator (MLE), to evaluate the likelihood that a detection is a real source. MLE uses the Sherpa modeling and fitting engine to fit a model of a background and source to multiple overlapping candidate source regions. A background model is calculated by simultaneously fitting the observed photon flux in multiple background regions. This model is used to determine the quality of the fit statistic for a background-only hypothesis in the potential source region. The statistic for a background-plus-source hypothesis is calculated by adding a Gaussian source model convolved with the appropriate Chandra point spread function (PSF) and simultaneously fitting the observed photon flux in each observation in the stack. Since a candidate source may be located anywhere in the field of view of each stacked observation, a different PSF must be used for each observation because of the strong spatial dependence of the Chandra PSF. The likelihood of a valid source being detected is a function of the two statistics (for background alone, and for background-plus-source). The MLE tool is an extensible Python module with potential for use by the general Chandra user.
Finding All Allowed Edges in a Bipartite Graph
Tassa, Tamir
2011-01-01
We consider the problem of finding all allowed edges in a bipartite graph $G=(V,E)$, i.e., all edges that are included in some maximum matching. We show that given any maximum matching in the graph, it is possible to perform this computation in linear time $O(n+m)$ (where $n=|V|$ and $m=|E|$). Hence, the time complexity of finding all allowed edges reduces to that of finding a single maximum matching, which is $O(n^{1/2}m)$ [Hopcroft and Karp 1973], or $O((n/\\log n)^{1/2}m)$ for dense graphs with $m=\\Theta(n^2)$ [Alt et al. 1991]. This time complexity improves upon that of the best known algorithms for the problem, which is $O(nm)$ ([Costa 1994] for bipartite graphs, and [Carvalho and Cheriyan 2005] for general graphs). Other algorithms for solving that problem are randomized algorithms due to [Rabin and Vazirani 1989] and [Cheriyan 1997], the runtime of which is $\\tilde{O}(n^{2.376})$. Our algorithm, apart from being deterministic, improves upon that time complexity for bipartite graphs when $m=O(n^r)$ and $...
The constraint rule of the maximum entropy principle
Uffink, J.
2001-01-01
The principle of maximum entropy is a method for assigning values to probability distributions on the basis of partial information. In usual formulations of this and related methods of inference one assumes that this partial information takes the form of a constraint on allowed probability distribut
Maximum-Entropy Inference with a Programmable Annealer
Chancellor, Nicholas; Vinci, Walter; Aeppli, Gabriel; Warburton, Paul A
2015-01-01
Optimisation problems in science and engineering typically involve finding the ground state (i.e. the minimum energy configuration) of a cost function with respect to many variables. If the variables are corrupted by noise then this approach maximises the likelihood that the solution found is correct. An alternative approach is to make use of prior statistical information about the noise in conjunction with Bayes's theorem. The maximum entropy solution to the problem then takes the form of a Boltzmann distribution over the ground and excited states of the cost function. Here we use a programmable Josephson junction array for the information decoding problem which we simulate as a random Ising model in a field. We show experimentally that maximum entropy decoding at finite temperature can in certain cases give competitive and even slightly better bit-error-rates than the maximum likelihood approach at zero temperature, confirming that useful information can be extracted from the excited states of the annealing...
Quantum-dot Carnot engine at maximum power.
Esposito, Massimiliano; Kawai, Ryoichi; Lindenberg, Katja; Van den Broeck, Christian
2010-04-01
We evaluate the efficiency at maximum power of a quantum-dot Carnot heat engine. The universal values of the coefficients at the linear and quadratic order in the temperature gradient are reproduced. Curzon-Ahlborn efficiency is recovered in the limit of weak dissipation.
20 CFR 617.47 - Moving allowance.
2010-04-01
... Employees' Benefits EMPLOYMENT AND TRAINING ADMINISTRATION, DEPARTMENT OF LABOR TRADE ADJUSTMENT ASSISTANCE... goods and personal effects of an individual and family, if any, shall not exceed the maximum number of... include the cost of insuring such goods and effects for their actual value or $10,000, whichever is...
45 CFR 74.27 - Allowable costs.
2010-10-01
... 45 Public Welfare 1 2010-10-01 2010-10-01 false Allowable costs. 74.27 Section 74.27 Public..., AND COMMERCIAL ORGANIZATIONS Post-Award Requirements Financial and Program Management § 74.27 Allowable costs. (a) For each kind of recipient, there is a particular set of Federal principles...
28 CFR 100.11 - Allowable costs.
2010-07-01
... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Allowable costs. 100.11 Section 100.11 Judicial Administration DEPARTMENT OF JUSTICE (CONTINUED) COST RECOVERY REGULATIONS, COMMUNICATIONS ASSISTANCE FOR LAW ENFORCEMENT ACT OF 1994 § 100.11 Allowable costs. (a) Costs that are eligible...
20 CFR 633.303 - Allowable costs.
2010-04-01
... occupation trained for and at not less than the wage specified in the agreement. (g) Travel costs. (1) The... to the overall administrative cost ceiling. (i) Allowances and reimbursements for board and advisory... grantee per quarter. (2) Allowances and loss of wages. Any individual or family member who is a member of...
75 FR 4098 - Utility Allowance Adjustments
2010-01-26
... URBAN DEVELOPMENT Utility Allowance Adjustments AGENCY: Office of the Chief Information Officer, HUD... are required to advise the Secretary of the need for and request of a new utility allowance for... whether the information will have practical utility; (2) Evaluate the accuracy of the agency's estimate...
44 CFR 13.22 - Allowable costs.
2010-10-01
... uniform cost accounting standards that comply with cost principles acceptable to the Federal agency. ... STATE AND LOCAL GOVERNMENTS Post-Award Requirements Financial Administration § 13.22 Allowable costs. (a... increment above allowable costs) to the grantee or subgrantee. (b) Applicable cost principles. For each...
32 CFR 33.22 - Allowable costs.
2010-07-01
... accounting standards that comply with cost principles acceptable to the Federal agency. ... Post-Award Requirements Financial Administration § 33.22 Allowable costs. (a) Limitation on use of... allowable costs) to the grantee or subgrantee. (b) Applicable cost principles. For each kind of...
36 CFR 1207.22 - Allowable costs.
2010-07-01
... uniform cost accounting standards that comply with cost principles acceptable to the Federal agency. ... GOVERNMENTS Post-Award Requirements Financial Administration § 1207.22 Allowable costs. (a) Limitation on use... increment above allowable costs) to the grantee or subgrantee. (b) Applicable cost principles. For each...
34 CFR 74.27 - Allowable costs.
2010-07-01
... Procedures or uniform cost accounting standards that comply with cost principles acceptable to ED. (b) The... OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT ORGANIZATIONS Post-Award Requirements Financial... principles for determining allowable costs. Allowability of costs are determined in accordance with the...
5 CFR 180.104 - Allowable claims.
2010-01-01
... mobile homes may be allowed only in cases of collision, theft, or vandalism. (5) Money. Claims for money... claimant's supervisor. (4) Mobile homes. Claims may be allowed for damage to or loss of mobile homes and their contents under the provisions of § 180.104(c)(2). Claims for structural damage to mobile...
38 CFR 49.27 - Allowable costs.
2010-07-01
... ADMINISTRATIVE REQUIREMENTS FOR GRANTS AND AGREEMENTS WITH INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT ORGANIZATIONS Post-Award Requirements Financial and Program Management § 49.27 Allowable...-Profit Organizations.” The allowability of costs incurred by institutions of higher education...
20 CFR 435.27 - Allowable costs.
2010-04-01
... AGREEMENTS WITH INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, OTHER NON-PROFIT ORGANIZATIONS, AND COMMERCIAL ORGANIZATIONS Post-Award Requirements Financial and Program Management § 435.27 Allowable costs. For each kind... Organizations.” (c) Allowability of costs incurred by institutions of higher education is determined...
28 CFR 70.27 - Allowable costs.
2010-07-01
... AND AGREEMENTS (INCLUDING SUBAWARDS) WITH INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS AND OTHER NON-PROFIT ORGANIZATIONS Post-Award Requirements Financial and Program Management § 70.27 Allowable costs. (a... Organizations.” The allowability of costs incurred by institutions of higher education is determined...
15 CFR 14.27 - Allowable costs.
2010-01-01
... GRANTS AND AGREEMENTS WITH INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, OTHER NON-PROFIT, AND COMMERCIAL ORGANIZATIONS Post-Award Requirements Financial and Program Management § 14.27 Allowable costs. For each kind of... Organizations.” The allowability of costs incurred by institutions of higher education is determined...
24 CFR 17.43 - Allowable claims.
2010-04-01
... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Allowable claims. 17.43 Section 17.43 Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development..., superior authority. (6) Clothing and accessories. Claims may be allowed for damage to, or loss of, clothing...
29 CFR 1470.22 - Allowable costs.
2010-07-01
... to that circular 48 CFR part 31. Contract Cost Principles and Procedures, or uniform cost accounting... grantee or subgrantee. (b) Applicable cost principles. For each kind of organization, there is a set of Federal principles for determining allowable costs. Allowable costs will be determined in accordance...
45 CFR 2541.220 - Allowable costs.
2010-10-01
... accounting standards that comply with cost principles acceptable to the Federal agency. ... the grantee or subgrantee. (b) Applicable cost principles. For each kind of organization, there is a set of Federal principles for determining allowable costs. Allowable costs will be determined...
Danilo F. Pereira
2005-08-01
Full Text Available Considerando o comportamento social, é sugestivo que a freqüência e a intensidade de interações agressivas, o total de coesão social e compreensão da extensão de vícios sociais possam ser utilizados para avaliação de bem-estar. Este trabalho propõe que a freqüência de utilização de determinados locais dentro do galpão possa ser usada como variável para monitorar estados de bem-estar térmico e/ou estresse das aves alojadas. A partir de dados registrados no verão de 2000-2001, esta pesquisa identificou as temperaturas críticas máximas (tc máx de matrizes pesadas, individualmente, por meio de análise estatística da freqüência de uso de locais previamente estabelecidos, utilizando a tecnologia de identificação eletrônica. Os valores das tc máx individuais variaram de 30 °C ± 0,2 ºC a 32,3 ºC ± 0,2 ºC e a temperatura crítica máxima média para o grupo foi 30,9 ºC ± 0,8 ºC.Considering the social behavior, it is suggested that the frequency and the intensity of aggressive interactions, as the well as the total social cohesion, and the understanding of social behavior can be used for welfare evaluation. This research proposes that the frequency of use of specific places inside the bird's housing can be used as variable to monitor thermal welfare status and/or the stress level of the lodged birds. From data registered in the summer of 2000/2001, this study identified the maximum critical temperatures (ct max of the female broiler breeders individually, using statistical analysis of the use of previously determined places, applying the technology of electronic identification. The ct max values varied from 30 °C ± 0,2 ºC to 32,3 ºC ± 0,2 ºC and the critical temperature maximum average for the group was 30,9 ºC ± 0,8 ºC.
MB Distribution and its application using maximum entropy approach
Bhadra Suman
2016-01-01
Full Text Available Maxwell Boltzmann distribution with maximum entropy approach has been used to study the variation of political temperature and heat in a locality. We have observed that the political temperature rises without generating any political heat when political parties increase their attractiveness by intense publicity, but voters do not shift their loyalties. It has also been shown that political heat is generated and political entropy increases with political temperature remaining constant when parties do not change their attractiveness, but voters shift their loyalties (to more attractive parties.
HIgh Temperature Photocatalysis over Semiconductors
Westrich, Thomas A.
temperature-dependent quantum efficiency term, and is directly driven by bulk photocatalyst crystal parameters: maximum phonon energy and the number of phonons allowed per unit cell. This analysis extends to multiple photocatalysts and can explain experimental observations of photocatalytic oxidation rates with varied reactant concentrations. Lastly, this dissertation applies this knowledge to a thermo-catalytic reaction (CO-oxidation) using a Au/TiO 2 catalyst. The combined photo/thereto-catalytic reaction showed a 10-25% increase in CO conversion during a temperature programmed reaction experiment.
Keynes, family allowances and Keynesian economic policy
Pressman, Steven
2014-01-01
This paper provides a short history of family allowances and documents the fact that Keynes supported family allowances as early as the 1920s, continuing through the 1930s and early 1940s. Keynes saw this policy as a way to help households raise their children and also as a way to increase consumption without reducing business investment. The paper goes on to argue that a policy of family allowances is consistent with Keynesian economics. Finally, the paper uses the Luxembourg Income Study to...
Prediction of three dimensional maximum isometric neck strength.
Fice, Jason B; Siegmund, Gunter P; Blouin, Jean-Sébastien
2014-09-01
We measured maximum isometric neck strength under combinations of flexion/extension, lateral bending and axial rotation to determine whether neck strength in three dimensions (3D) can be predicted from principal axes strength. This would allow biomechanical modelers to validate their neck models across many directions using only principal axis strength data. Maximum isometric neck moments were measured in 9 male volunteers (29±9 years) for 17 directions. The 3D moments were normalized by the principal axis moments, and compared to unity for all directions tested. Finally, each subject's maximum principal axis moments were used to predict their resultant moment in the off-axis directions. Maximum moments were 30±6 N m in flexion, 32±9 N m in lateral bending, 51±11 N m in extension, and 13±5 N m in axial rotation. The normalized 3D moments were not significantly different from unity (95% confidence interval contained one), except for three directions that combined ipsilateral axial rotation and lateral bending; in these directions the normalized moments exceeded one. Predicted resultant moments compared well to the actual measured values (r2=0.88). Despite exceeding unity, the normalized moments were consistent across subjects to allow prediction of maximum 3D neck strength using principal axes neck strength.
Maximum Power Point Tracking Based on Sliding Mode Control
Nimrod Vázquez
2015-01-01
Full Text Available Solar panels, which have become a good choice, are used to generate and supply electricity in commercial and residential applications. This generated power starts with the solar cells, which have a complex relationship between solar irradiation, temperature, and output power. For this reason a tracking of the maximum power point is required. Traditionally, this has been made by considering just current and voltage conditions at the photovoltaic panel; however, temperature also influences the process. In this paper the voltage, current, and temperature in the PV system are considered to be a part of a sliding surface for the proposed maximum power point tracking; this means a sliding mode controller is applied. Obtained results gave a good dynamic response, as a difference from traditional schemes, which are only based on computational algorithms. A traditional algorithm based on MPPT was added in order to assure a low steady state error.
CORA - emission line fitting with Maximum Likelihood
Ness, J.-U.; Wichmann, R.
2002-07-01
The advent of pipeline-processed data both from space- and ground-based observatories often disposes of the need of full-fledged data reduction software with its associated steep learning curve. In many cases, a simple tool doing just one task, and doing it right, is all one wishes. In this spirit we introduce CORA, a line fitting tool based on the maximum likelihood technique, which has been developed for the analysis of emission line spectra with low count numbers and has successfully been used in several publications. CORA uses a rigorous application of Poisson statistics. From the assumption of Poissonian noise we derive the probability for a model of the emission line spectrum to represent the measured spectrum. The likelihood function is used as a criterion for optimizing the parameters of the theoretical spectrum and a fixed point equation is derived allowing an efficient way to obtain line fluxes. As an example we demonstrate the functionality of the program with an X-ray spectrum of Capella obtained with the Low Energy Transmission Grating Spectrometer (LETGS) on board the Chandra observatory and choose the analysis of the Ne IX triplet around 13.5 Å.
Sign Patterns That Allow the Given Matrix
邵燕灵; 孙良
2003-01-01
Let P be a property referring to a real matrix. For a sign pattern A, if there exists a real matrix B in the qualitative class of A such that B has property P, then we say A allows P. Three cases that A allows an M-matrix, an inverse M-matrix and a P0-matrix are considered. The complete characterizations are obtained.
Progress Report on Alloy 617 Time Dependent Allowables
Wright, Julie Knibloe [Idaho National Lab. (INL), Idaho Falls, ID (United States)
2015-06-01
Time dependent allowable stresses are required in the ASME Boiler and Pressure Vessel Code for design of components in the temperature range where time dependent deformation (i.e., creep) is expected to become significant. There are time dependent allowable stresses in Section IID of the Code for use in the non-nuclear construction codes, however, there are additional criteria that must be considered in developing time dependent allowables for nuclear components. These criteria are specified in Section III NH. St is defined as the lesser of three quantities: 100% of the average stress required to obtain a total (elastic, plastic, primary and secondary creep) strain of 1%; 67% of the minimum stress to cause rupture; and 80% of the minimum stress to cause the initiation of tertiary creep. The values are reported for a range of temperatures and for time increments up to 100,000 hours. These values are determined from uniaxial creep tests, which involve the elevated temperature application of a constant load which is relatively small, resulting in deformation over a long time period prior to rupture. The stress which is the minimum resulting from these criteria is the time dependent allowable stress St. In this report data from a large number of creep and creep-rupture tests on Alloy 617 are analyzed using the ASME Section III NH criteria. Data which are used in the analysis are from the ongoing DOE sponsored high temperature materials program, form Korea Atomic Energy Institute through the Generation IV VHTR Materials Program and historical data from previous HTR research and vendor data generated in developing the alloy. It is found that the tertiary creep criterion determines St at highest temperatures, while the stress to cause 1% total strain controls at low temperatures. The ASME Section III Working Group on Allowable Stress Criteria has recommended that the uncertainties associated with determining the onset of tertiary creep and the lack of significant
Receiver function estimated by maximum entropy deconvolution
吴庆举; 田小波; 张乃铃; 李卫平; 曾融生
2003-01-01
Maximum entropy deconvolution is presented to estimate receiver function, with the maximum entropy as the rule to determine auto-correlation and cross-correlation functions. The Toeplitz equation and Levinson algorithm are used to calculate the iterative formula of error-predicting filter, and receiver function is then estimated. During extrapolation, reflective coefficient is always less than 1, which keeps maximum entropy deconvolution stable. The maximum entropy of the data outside window increases the resolution of receiver function. Both synthetic and real seismograms show that maximum entropy deconvolution is an effective method to measure receiver function in time-domain.
Regulatory treatment of allowances and compliance costs
Rose, K. [National Regulatory Research Institute, Columbus, OH (United States)
1993-07-01
The Clean Air Act Amendments of 1990 (CAAA) established a national emission allowance trading system, a market-based form of environmental regulation designed to reduce and limit sulfur dioxide emissions. However, the allowance trading system is being applied primarily to an economically regulated electric utility industry. The combining of the new form of environmental regulation and economic regulation of electric utilities has raised a number of questions including what the role should be of the federal and state utility regulating commissions and how those actions will affect the decision making process of the utilities and the allowance market. There are several dimensions to the regulatory problems that commissions face. Allowances and utility compliance expenditures have implications for least-cost/IPR (integrated resource planning), prudence review procedures, holding company and multistate utility regulation and ratemaking treatment. The focus of this paper is on the ratemaking treatment. The following topics are covered: ratemaking treatment of allowances and compliance costs; Traditional cost-recovery mechanisms; limitations to the traditional approach; traditional approach and the allowance trading market; market-based cost recovery mechanisms; methods of determining the benchmark; determining the split between ratepayers and the utility; other regulatory approaches; limitations of incentive mechanisms.
Generalized Relativistic Wave Equations with Intrinsic Maximum Momentum
Ching, Chee Leong
2013-01-01
We examine the nonperturbative effect of maximum momentum on the relativistic wave equations. In momentum representation, we obtain the exact eigen-energies and wavefunctions of one-dimensional Klein-Gordon and Dirac equation with linear confining potentials, and the Dirac oscillator. Bound state solutions are only possible when the strength of scalar potential are stronger than vector potential. The energy spectrum of the systems studied are bounded from above, whereby classical characteristics are observed in the uncertainties of position and momentum operators. Also, there is a truncation in the maximum number of bound states that is allowed. Some of these quantum-gravitational features may have future applications.
Generalized relativistic wave equations with intrinsic maximum momentum
Ching, Chee Leong; Ng, Wei Khim
2014-05-01
We examine the nonperturbative effect of maximum momentum on the relativistic wave equations. In momentum representation, we obtain the exact eigen-energies and wave functions of one-dimensional Klein-Gordon and Dirac equation with linear confining potentials, and the Dirac oscillator. Bound state solutions are only possible when the strength of scalar potential is stronger than vector potential. The energy spectrum of the systems studied is bounded from above, whereby classical characteristics are observed in the uncertainties of position and momentum operators. Also, there is a truncation in the maximum number of bound states that is allowed. Some of these quantum-gravitational features may have future applications.
A maximum in the strength of nanocrystalline copper
Schiøtz, Jakob; Jacobsen, Karsten Wedel
2003-01-01
We used molecular dynamics simulations with system sizes up to 100 million atoms to simulate plastic deformation of nanocrystalline copper. By varying the grain size between 5 and 50 nanometers, we show that the flow stress and thus the strength exhibit a maximum at a grain size of 10 to 15...... nanometers. This maximum is because of a shift in the microscopic deformation mechanism from dislocation-mediated plasticity in the coarse-grained material to grain boundary sliding in the nanocrystalline region. The simulations allow us to observe the mechanisms behind the grain-size dependence...
Maximum Power from a Solar Panel
Michael Miller
2010-01-01
Full Text Available Solar energy has become a promising alternative to conventional fossil fuel sources. Solar panels are used to collect solar radiation and convert it into electricity. One of the techniques used to maximize the effectiveness of this energy alternative is to maximize the power output of the solar collector. In this project the maximum power is calculated by determining the voltage and the current of maximum power. These quantities are determined by finding the maximum value for the equation for power using differentiation. After the maximum values are found for each time of day, each individual quantity, voltage of maximum power, current of maximum power, and maximum power is plotted as a function of the time of day.
The tropical lapse rate steepened during the Last Glacial Maximum.
Loomis, Shannon E; Russell, James M; Verschuren, Dirk; Morrill, Carrie; De Cort, Gijs; Sinninghe Damsté, Jaap S; Olago, Daniel; Eggermont, Hilde; Street-Perrott, F Alayne; Kelly, Meredith A
2017-01-01
The gradient of air temperature with elevation (the temperature lapse rate) in the tropics is predicted to become less steep during the coming century as surface temperature rises, enhancing the threat of warming in high-mountain environments. However, the sensitivity of the lapse rate to climate change is uncertain because of poor constraints on high-elevation temperature during past climate states. We present a 25,000-year temperature reconstruction from Mount Kenya, East Africa, which demonstrates that cooling during the Last Glacial Maximum was amplified with elevation and hence that the lapse rate was significantly steeper than today. Comparison of our data with paleoclimate simulations indicates that state-of-the-art models underestimate this lapse-rate change. Consequently, future high-elevation tropical warming may be even greater than predicted.
The tropical lapse rate steepened during the Last Glacial Maximum
Loomis, Shannon E.; Russell, James M.; Verschuren, Dirk; Morrill, Carrie; De Cort, Gijs; Sinninghe Damsté, Jaap S.; Olago, Daniel; Eggermont, Hilde; Street-Perrott, F. Alayne; Kelly, Meredith A.
2017-01-01
The gradient of air temperature with elevation (the temperature lapse rate) in the tropics is predicted to become less steep during the coming century as surface temperature rises, enhancing the threat of warming in high-mountain environments. However, the sensitivity of the lapse rate to climate change is uncertain because of poor constraints on high-elevation temperature during past climate states. We present a 25,000-year temperature reconstruction from Mount Kenya, East Africa, which demonstrates that cooling during the Last Glacial Maximum was amplified with elevation and hence that the lapse rate was significantly steeper than today. Comparison of our data with paleoclimate simulations indicates that state-of-the-art models underestimate this lapse-rate change. Consequently, future high-elevation tropical warming may be even greater than predicted. PMID:28138544
Climate Sensitivity of the Last Glacial Maximum from Paleoclimate Simulations and Observations
Otto-Bliesner, B. L.; Brady, E.; Kothavala, Z.
2004-12-01
Global coupled climate models run for future scenarios of increasing atmospheric CO2 give a range of response of the global average surface temperature. Regional responses, including the North Atlantic overturning circulation and tropical Pacific ENSO, also vary significantly among models. The second phase of the Paleoclimate Modeling Intercomparison Project (PMIP 2) is coordinating simulations and data syntheses for the Last Glacial Maximum (21,000 years before present) to allow another assessment of climate sensitivity. Atmospheric CO2 concentrations at the Last Glacial Maximum (LGM) have been estimated using measurements from ice cores to be 185 ppmv, approximately 50% of present-day values. Global, annual mean surface temperature simulated by the slab ocean version of the National Center for Atmospheric Research (NCAR) Community Climate System Model (CCSM3) shows a cooling of -2.8°C for LGM CO2 levels and a warming of 2.5°C for a doubling of CO2. Slab and coupled CCSM3 simulations that include the reductions of the other atmospheric trace gases and the large ice sheets covering North America and Eurasia at LGM give cooling in agreement with proxy inferences and indicate that LGM CO2 explains about half of the global cooling at LGM. Regional signatures of the climate system to changed LGM forcing are also an important measure of climate sensitivity and results from the fully coupled version of CCSM3 will be shown.
Chen, Jincan; Yan, Zijun; Wu, Liqing
1996-06-01
Considering a thermoelectric generator as a heat engine cycle, the general differential equations of the temperature field inside thermoelectric elements are established by means of nonequilibrium thermodynamics. These equations are used to study the influence of heat leak, Joule's heat, and Thomson heat on the performance of the thermoelectric generator. New expressions are derived for the power output and the efficiency of the thermoelectric generator. The maximum power output is calculated and the optimal matching condition of load is determined. The maximum efficiency is discussed by a representative numerical example. The aim of this research is to provide some novel conclusions and redress some errors existing in a related investigation.
Allowable levels of take for the trade in Nearctic songbirds
Johnson, Fred A.; Walters, Matthew A.H.; Boomer, G. Scott
2012-01-01
The take of Nearctic songbirds for the caged-bird trade is an important cultural and economic activity in Mexico, but its sustainability has been questioned. We relied on the theta-logistic population model to explore options for setting allowable levels of take for 11 species of passerines that were subject to legal take in Mexico in 2010. Because estimates of population size necessary for making periodic adjustments to levels of take are not routinely available, we examined the conditions under which a constant level of take might contribute to population depletion (i.e., a population below its level of maximum net productivity). The chance of depleting a population is highest when levels of take are based on population sizes that happen to be much lower or higher than the level of maximum net productivity, when environmental variation is relatively high and serially correlated, and when the interval between estimation of population size is relatively long (≥5 years). To estimate demographic rates of songbirds involved in the Mexican trade we relied on published information and allometric relationships to develop probability distributions for key rates, and then sampled from those distributions to characterize the uncertainty in potential levels of take. Estimates of the intrinsic rate of growth (r) were highly variable, but median estimates were consistent with those expected for relatively short-lived, highly fecund species. Allowing for the possibility of nonlinear density dependence generally resulted in allowable levels of take that were lower than would have been the case under an assumption of linearity. Levels of take authorized by the Mexican government in 2010 for the 11 species we examined were small in comparison to relatively conservative allowable levels of take (i.e., those intended to achieve 50% of maximum sustainable yield). However, the actual levels of take in Mexico are unknown and almost certainly exceed the authorized take. Also, the take
45 CFR 34.4 - Allowable claims.
2010-10-01
... government-owned or operated parking lot or garage incident to employment. This subsection does not include... amount allowed is the value of the vehicle at the time of loss as determined by the National Automobile.... Damage or loss of personal property, including baggage and household items, while being transported by...
45 CFR 2543.27 - Allowable costs.
2010-10-01
... Welfare Regulations Relating to Public Welfare (Continued) CORPORATION FOR NATIONAL AND COMMUNITY SERVICE GRANTS AND AGREEMENTS WITH INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT... Organizations.” The allowability of costs incurred by institutions of higher education is determined in...
34 CFR 80.22 - Allowable costs.
2010-07-01
... CFR part 31. Contract Cost Principles and Procedures, or uniform cost accounting standards that comply... COOPERATIVE AGREEMENTS TO STATE AND LOCAL GOVERNMENTS Post-Award Requirements Financial Administration § 80.22... kind of organization, there is a set of Federal principles for determining allowable costs. For...
13 CFR 143.22 - Allowable costs.
2010-01-01
... to that circular 48 CFR part 31. Contract Cost Principles and Procedures, or uniform cost accounting... Financial Administration § 143.22 Allowable costs. (a) Limitation on use of funds. Grant funds may be used... grantee or subgrantee. (b) Applicable cost principles. For each kind of organization, there is a set...
38 CFR 43.22 - Allowable costs.
2010-07-01
... accounting standards that comply with cost principles acceptable to the Federal agency. ... Requirements Financial Administration § 43.22 Allowable costs. (a) Limitation on use of funds. Grant funds may... the grantee or subgrantee. (b) Applicable cost principles. For each kind of organization, there is...
22 CFR 135.22 - Allowable costs.
2010-04-01
... Procedures, or uniform cost accounting standards that comply with cost principles acceptable to the Federal... AGREEMENTS TO STATE AND LOCAL GOVERNMENTS Post-Award Requirements Financial Administration § 135.22 Allowable... principles. For each kind of organization, there is a set of Federal principles for determining...
40 CFR 31.22 - Allowable costs.
2010-07-01
... accounting standards that comply with cost principles acceptable to the Federal agency. ... Requirements Financial Administration § 31.22 Allowable costs. (a) Limitation on use of funds. Grant funds may... the grantee or sub-grantee. (b) Applicable cost principles. For each kind of organization, there is...
45 CFR 92.22 - Allowable costs.
2010-10-01
... to that circular 48 CFR Part 31. Contract Cost Principles and Procedures, or uniform cost accounting... Financial Administration § 92.22 Allowable costs. (a) Limitation on use of funds. Grant funds may be used... grantee or subgrantee. (b) Applicable cost principles. For each kind of organization, there is a set...
7 CFR 550.25 - Allowable costs.
2010-01-01
... Regulations of the Department of Agriculture (Continued) AGRICULTURAL RESEARCH SERVICE, DEPARTMENT OF... Financial Management § 550.25 Allowable costs. For each kind of Cooperator, there is a set of Federal... Acquisition Regulation (FAR) at 48 CFR part 31. Program Management ...
22 CFR 145.27 - Allowable costs.
2010-04-01
... Relations DEPARTMENT OF STATE CIVIL RIGHTS GRANTS AND AGREEMENTS WITH INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT ORGANIZATIONS Post-Award Requirements Financial and Program Management § 145...-Profit Organizations.” The allowability of costs incurred by institutions of higher education...
22 CFR 518.27 - Allowable costs.
2010-04-01
... INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT ORGANIZATIONS Post-Award Requirements Financial and Program Management § 518.27 Allowable costs. For each kind of recipient, there is a set of... by institutions of higher education is determined in accordance with the provisions of OMB Circular...
36 CFR 1210.27 - Allowable costs.
2010-07-01
... RULES UNIFORM ADMINISTRATIVE REQUIREMENTS FOR GRANTS AND AGREEMENTS WITH INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT ORGANIZATIONS Post-Award Requirements Financial and Program Management § 1210.27 Allowable costs. For each kind of recipient, there is a set of Federal principles...
Making It Personal: Per Capita Carbon Allowances
Fawcett, Tina; Hvelplund, Frede; Meyer, Niels I
2009-01-01
The Chapter highligts the importance of introducing new, efficient schemes for mitigation of global warming. One such scheme is Personal Carbon Allowances (PCA), whereby individuals are allotted a tradable ration of CO2 emission per year.This chapter reviews the fundamentals of PCA and analyzes its...
Judicial Deference Allows European Consensus to Emerge
Dothan, Shai
2017-01-01
conceived as competing doctrines: the more there is of one, the less there is of another. This paper suggests a novel rationale for the emerging consensus doctrine: the doctrine can allow the ECHR to make good policies by drawing on the independent decision-making of many similar countries. In light of that...
77 FR 34218 - Clothing Allowance; Correction
2012-06-11
... construed to impose a restriction that VA did not intend. This document corrects that error. DATES: This... Service, Veterans Benefits Administration, Department of Veterans Affairs, 810 Vermont Avenue NW... medication would be eligible for a clothing allowance for each such appliance or medication if each...
49 CFR 266.11 - Allowable costs.
2010-10-01
... Management Circular 74-4; and costs of projects eligible under § 266.7 of this part. All allowable costs shall be authorized by a fully executed grant agreement. A State may incur costs prior to the execution... need to incur costs prior to the execution of a grant agreement, has authorized the costs in writing...
33 CFR 136.211 - Compensation allowable.
2010-07-01
... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Compensation allowable. 136.211 Section 136.211 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... PROCEDURES; DESIGNATION OF SOURCE; AND ADVERTISEMENT Procedures for Particular Claims § 136.211...
33 CFR 136.205 - Compensation allowable.
2010-07-01
... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Compensation allowable. 136.205 Section 136.205 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... PROCEDURES; DESIGNATION OF SOURCE; AND ADVERTISEMENT Procedures for Particular Claims § 136.205...
33 CFR 136.241 - Compensation allowable.
2010-07-01
... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Compensation allowable. 136.241 Section 136.241 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... PROCEDURES; DESIGNATION OF SOURCE; AND ADVERTISEMENT Procedures for Particular Claims § 136.241...
33 CFR 136.223 - Compensation allowable.
2010-07-01
... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Compensation allowable. 136.223 Section 136.223 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... PROCEDURES; DESIGNATION OF SOURCE; AND ADVERTISEMENT Procedures for Particular Claims § 136.223...
33 CFR 136.217 - Compensation allowable.
2010-07-01
... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Compensation allowable. 136.217 Section 136.217 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... PROCEDURES; DESIGNATION OF SOURCE; AND ADVERTISEMENT Procedures for Particular Claims § 136.217...
33 CFR 136.235 - Compensation allowable.
2010-07-01
... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Compensation allowable. 136.235 Section 136.235 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... PROCEDURES; DESIGNATION OF SOURCE; AND ADVERTISEMENT Procedures for Particular Claims § 136.235...
33 CFR 136.229 - Compensation allowable.
2010-07-01
... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Compensation allowable. 136.229 Section 136.229 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... PROCEDURES; DESIGNATION OF SOURCE; AND ADVERTISEMENT Procedures for Particular Claims § 136.229...
50 CFR 80.15 - Allowable costs.
2010-10-01
...) FINANCIAL ASSISTANCE-WILDLIFE SPORT FISH RESTORATION PROGRAM ADMINISTRATIVE REQUIREMENTS, PITTMAN-ROBERTSON WILDLIFE RESTORATION AND DINGELL-JOHNSON SPORT FISH RESTORATION ACTS § 80.15 Allowable costs. (a) What are... designed to include purposes other than those eligible under either the Dingell-Johnson Sport Fish...
43 CFR 12.62 - Allowable costs.
2010-10-01
... Public Lands: Interior Office of the Secretary of the Interior ADMINISTRATIVE AND AUDIT REQUIREMENTS AND COST PRINCIPLES FOR ASSISTANCE PROGRAMS Uniform Administrative Requirements for Grants and Cooperative... increment above allowable costs) to the grantee or subgrantee. (b) Applicable cost principles. For each...
Suligowski, Roman
2014-05-01
Probable Maximum Precipitation based upon the physical mechanisms of precipitation formation at the Kielce Upland. This estimation stems from meteorological analysis of extremely high precipitation events, which occurred in the area between 1961 and 2007 causing serious flooding from rivers that drain the entire Kielce Upland. Meteorological situation has been assessed drawing on the synoptic maps, baric topography charts, satellite and radar images as well as the results of meteorological observations derived from surface weather observation stations. Most significant elements of this research include the comparison between distinctive synoptic situations over Europe and subsequent determination of typical rainfall generating mechanism. This allows the author to identify the source areas of air masses responsible for extremely high precipitation at the Kielce Upland. Analysis of the meteorological situations showed, that the source areas for humid air masses which cause the largest rainfalls at the Kielce Upland are the area of northern Adriatic Sea and the north-eastern coast of the Black Sea. Flood hazard at the Kielce Upland catchments was triggered by daily precipitation of over 60 mm. The highest representative dew point temperature in source areas of warm air masses (these responsible for high precipitation at the Kielce Upland) exceeded 20 degrees Celsius with a maximum of 24.9 degrees Celsius while precipitable water amounted to 80 mm. The value of precipitable water is also used for computation of factors featuring the system, namely the mass transformation factor and the system effectiveness factor. The mass transformation factor is computed based on precipitable water in the feeding mass and precipitable water in the source area. The system effectiveness factor (as the indicator of the maximum inflow velocity and the maximum velocity in the zone of front or ascending currents, forced by orography) is computed from the quotient of precipitable water in
The inverse maximum dynamic flow problem
BAGHERIAN; Mehri
2010-01-01
We consider the inverse maximum dynamic flow (IMDF) problem.IMDF problem can be described as: how to change the capacity vector of a dynamic network as little as possible so that a given feasible dynamic flow becomes a maximum dynamic flow.After discussing some characteristics of this problem,it is converted to a constrained minimum dynamic cut problem.Then an efficient algorithm which uses two maximum dynamic flow algorithms is proposed to solve the problem.
The evolution of maximum body size of terrestrial mammals.
Smith, Felisa A; Boyer, Alison G; Brown, James H; Costa, Daniel P; Dayan, Tamar; Ernest, S K Morgan; Evans, Alistair R; Fortelius, Mikael; Gittleman, John L; Hamilton, Marcus J; Harding, Larisa E; Lintulaakso, Kari; Lyons, S Kathleen; McCain, Christy; Okie, Jordan G; Saarinen, Juha J; Sibly, Richard M; Stephens, Patrick R; Theodor, Jessica; Uhen, Mark D
2010-11-26
The extinction of dinosaurs at the Cretaceous/Paleogene (K/Pg) boundary was the seminal event that opened the door for the subsequent diversification of terrestrial mammals. Our compilation of maximum body size at the ordinal level by sub-epoch shows a near-exponential increase after the K/Pg. On each continent, the maximum size of mammals leveled off after 40 million years ago and thereafter remained approximately constant. There was remarkable congruence in the rate, trajectory, and upper limit across continents, orders, and trophic guilds, despite differences in geological and climatic history, turnover of lineages, and ecological variation. Our analysis suggests that although the primary driver for the evolution of giant mammals was diversification to fill ecological niches, environmental temperature and land area may have ultimately constrained the maximum size achieved.
Stute, M. [Lamont-Doherty Earth Observatory, New York (United States)
1998-12-31
A paleo-temperature record derived from noble gases dissolved in groundwater indicates that lowland equatorial Brazil has been about 5 deg C cooler during the glacial maximum that today. This new evidence contradicts the long-held belief that the tropical regions maintained their warm climate during the last glacial maximum. It appears now that the tropical Americas are characterized by a temperature sensitivity comparable to that in higher latitudes. (author) 14 refs.
High-temperature responses of North American cacti
Smith, S.D.; Didden-Zopfy, B.; Nobel, P.S.
1984-04-01
High-temperature tolerances of 14 species of North American cacti were investigated. A reduction in the proportion of chlorenchyma cells taking up a vital stain (neutral red) and reduced nocturnal acid accumulation were used as indicators of high-temperature damage. All species tolerated relatively high tissue temperatures, the mean maximum tolerance being 64/sup 0/C, with an absolute maximum of 69/sup 0/ for two species of ferocactus. Such tissue tolerances to high temperature may be unsurpassed in vascular plants. Morphological features can affect tissue temperatures. Specifically, thin-stemmed species such as the cylindropuntias attain lower maximum temperatures under identical microclimatic conditions than do more massive species; they also tend to be less tolerant of high-temperature stress. Stem diameter changes of three species of columnar ceriod cacti along a Sonoran Desert latitudinal transect were previously attributed to adaptation to progressively colder temperatures northward. Such changes can also be interpreted as a morphological adaptation to high temperatures, particularly in the southern Sonoran Desert. Interspecific differences in high-temperature tolerance may account for distributional differences among other species. Acclimation of high-temperature tolerances in response to increasing day/night air temperatures was observed in all 14 species, especially at higher growh temperatures. From 40/sup 0/ day/30/sup 0/ night to 50/sup 0//40/sup 0/, the tolerable tissue temperatures increased an average of 6/sup 0/. Half-times for the acclimation shifts were 1-3d. Although cacti attain extremely high tissue temperatures in desert habitats, tolerance of high temperatures and pronounced acclimation potential allow them to occur in some of the hottest habitats in North America.
ON A GENERALIZATION OF THE MAXIMUM ENTROPY THEOREM OF BURG
JOSÉ MARCANO
2017-01-01
Full Text Available In this article we introduce some matrix manipulations that allow us to obtain a version of the original Christoffel-Darboux formula, which is of interest in many applications of linear algebra. Using these developments matrix and Jensen’s inequality, we obtain the main result of this proposal, which is the generalization of the maximum entropy theorem of Burg for multivariate processes.
Adaptive Parallel Tempering for Stochastic Maximum Likelihood Learning of RBMs
Desjardins, Guillaume; Bengio, Yoshua
2010-01-01
Restricted Boltzmann Machines (RBM) have attracted a lot of attention of late, as one the principle building blocks of deep networks. Training RBMs remains problematic however, because of the intractibility of their partition function. The maximum likelihood gradient requires a very robust sampler which can accurately sample from the model despite the loss of ergodicity often incurred during learning. While using Parallel Tempering in the negative phase of Stochastic Maximum Likelihood (SML-PT) helps address the issue, it imposes a trade-off between computational complexity and high ergodicity, and requires careful hand-tuning of the temperatures. In this paper, we show that this trade-off is unnecessary. The choice of optimal temperatures can be automated by minimizing average return time (a concept first proposed by [Katzgraber et al., 2006]) while chains can be spawned dynamically, as needed, thus minimizing the computational overhead. We show on a synthetic dataset, that this results in better likelihood ...
Realization of allowable qeneralized quantum gates
无
2010-01-01
The most general duality gates were introduced by Long,Liu and Wang and named allowable generalized quantum gates (AGQGs,for short).By definition,an allowable generalized quantum gate has the form of U=YfkjsckUK,where Uk’s are unitary operators on a Hilbert space H and the coefficients ck’s are complex numbers with |Yfijo ck\\ ∧ 1 an d 1ck| <1 for all k=0,1,...,d-1.In this paper,we prove that an AGQG U=YfkZo ck∧k is realizable,i.e.there are two d by d unitary matrices W and V such that ck=W0kVk0 (0
Maximum Power Point Tracking Algorithms for Grid-Connected Photovoltaic Energy Conversion System
J.Surya Kumari
2013-12-01
Full Text Available As the use of energy is increasing, the requirements for the quality of the supplied electrical energy are more tighten. Energy is the most basic and essential of all resources. As conventional sources of energy are rapidly depleting and the cost of energy is rising, photovoltaic energy becomes a promising alternative source. Photovoltaic (PV generation is becoming increasingly important as a renewable source since it exhibits a great many merits such as cleanness, little maintenance and no noise. The output power of PV arrays is always changing with weather conditions, i.e., solar irradiation and atmospheric temperature. Therefore, a Maximum Power Point Tracking (MPPT control to extract maximum power from the PV arrays at real time becomes indispensable in PV generation system. In recent years, a large number of techniques have been proposed for tracking the maximum power point (MPP. MPPT is used in photovoltaic (PV systems to maximize the photovoltaic array output power, irrespective of the temperature and radiation conditions and of the load electrical characteristics the PV array output power is used to directly control the dc/dc converter, thus reducing the complexity of the system. The resulting system has high-efficiency. This paper presents in details comparison of most popular MPPT algorithms techniques which are Perturb & Observe algorithm(P&O and Improved Perturb & Observe algorithm(IPO. Improved Perturb & Observe algorithm (IPO, is a very promising technique that allows the increase of efficiency and reliability of such systems. Modeling and designing a PV system with Improved Perturb & Observe algorithm (IPO is remarkably more complex than implementing a standard MPPT technique. In this paper, Improved Perturb & Observe algorithm (IPO, system for PV arrays is proposed and analyzed.
Making It Personal: Per Capita Carbon Allowances
Fawcett, Tina; Hvelplund, Frede; Meyer, Niels I
2009-01-01
The Chapter highligts the importance of introducing new, efficient schemes for mitigation of global warming. One such scheme is Personal Carbon Allowances (PCA), whereby individuals are allotted a tradable ration of CO2 emission per year.This chapter reviews the fundamentals of PCA and analyzes its...... merits and problems. The United Kingdom and Denmark have been chosen as case studies because the energy situation and the institutional setup are quite different between the two countries....
Camacho, Agustín; Trefaut Rodrigues, Miguel; Navas, Carlos
2015-01-01
In ecological studies of thermal biology the thermal environment is most frequently described using the mean or other measures of central tendency in environmental temperatures. However, this procedure may hide biologically relevant thermal variation for ectotherms, potentially misleading interpretations. Extremes of operative temperatures (EOT) can help with this problem by bracketing the thermal environment of focal animals. Within this paper, we quantify how mean operative temperatures relate to the range of simultaneously available operative temperatures (a measure of error). We also show how EOT: 1) detect more thermal differences among microsites than measures of central tendency, like the mean OT, 2) allow inferring on microsite use by ectothermic animals, and 3) clarify the relationships between field operative temperatures and temperatures measured at weather stations (WS). To do that, we explored operative temperatures measured at four sites of the Brazilian Caatingas and their correspondent nearest weather stations. We found that the daily mean OT can hide temperature ranges of 41 °C simultaneously available at our study sites. In addition, EOT detected more thermal differences among microsites than central quantiles. We also show how EOT allow inferring about microsite use of ectothermic animals in a given site. Finally, the daily maximum temperature and the daily temperature range measured at WSs predicted well the minimum available field OT at localities many kilometers away. Based on our results, we recommend the use of EOT, instead of mean OT, in thermal ecology studies.
20 CFR 229.48 - Family maximum.
2010-04-01
... month on one person's earnings record is limited. This limited amount is called the family maximum. The family maximum used to adjust the social security overall minimum rate is based on the employee's Overall..., when any of the persons entitled to benefits on the insured individual's compensation would, except...
The maximum rotation of a galactic disc
Bottema, R
1997-01-01
The observed stellar velocity dispersions of galactic discs show that the maximum rotation of a disc is on average 63% of the observed maximum rotation. This criterion can, however, not be applied to small or low surface brightness (LSB) galaxies because such systems show, in general, a continuously
Individual Module Maximum Power Point Tracking for Thermoelectric Generator Systems
Vadstrup, Casper; Schaltz, Erik; Chen, Min
2013-07-01
In a thermoelectric generator (TEG) system the DC/DC converter is under the control of a maximum power point tracker which ensures that the TEG system outputs the maximum possible power to the load. However, if the conditions, e.g., temperature, health, etc., of the TEG modules are different, each TEG module will not produce its maximum power. If each TEG module is controlled individually, each TEG module can be operated at its maximum power point and the TEG system output power will therefore be higher. In this work a power converter based on noninverting buck-boost converters capable of handling four TEG modules is presented. It is shown that, when each module in the TEG system is operated under individual maximum power point tracking, the system output power for this specific application can be increased by up to 8.4% relative to the situation when the modules are connected in series and 16.7% relative to the situation when the modules are connected in parallel.
Duality of Maximum Entropy and Minimum Divergence
Shinto Eguchi
2014-06-01
Full Text Available We discuss a special class of generalized divergence measures by the use of generator functions. Any divergence measure in the class is separated into the difference between cross and diagonal entropy. The diagonal entropy measure in the class associates with a model of maximum entropy distributions; the divergence measure leads to statistical estimation via minimization, for arbitrarily giving a statistical model. The dualistic relationship between the maximum entropy model and the minimum divergence estimation is explored in the framework of information geometry. The model of maximum entropy distributions is characterized to be totally geodesic with respect to the linear connection associated with the divergence. A natural extension for the classical theory for the maximum likelihood method under the maximum entropy model in terms of the Boltzmann-Gibbs-Shannon entropy is given. We discuss the duality in detail for Tsallis entropy as a typical example.
Irani Lauer Lellis
2012-06-01
Full Text Available The practice of giving allowance is used by several parents in different parts of the world and can contribute to the economic education of children. This study aimed to investigate the purposes of the allowance with 32 parents of varying incomes. We used the focus group technique and Alceste software to analyze the data. The results involved two classes related to the process of using the allowance. These classes have covered aspects of the role of socialization and education allowance, serving as an instrument of reward, but sometimes encouraging bad habits in children. The justification of the fathers concerning the amount of money to be given to the children and when to stop giving allowance were also highlighted. Keywords: allowance; economic socialization; parenting practices.
Structure of Turbulence in Katabatic Flows Below and Above the Wind-Speed Maximum
Grachev, Andrey A.; Leo, Laura S.; Sabatino, Silvana Di; Fernando, Harindra J. S.; Pardyjak, Eric R.; Fairall, Christopher W.
2016-06-01
Measurements of small-scale turbulence made in the atmospheric boundary layer over complex terrain during the Mountain Terrain Atmospheric Modeling and Observations (MATERHORN) Program are used to describe the structure of turbulence in katabatic flows. Turbulent and mean meteorological data were continuously measured on four towers deployed along the east lower slope (2-4°) of Granite Mountain near Salt Lake City in Utah, USA. The multi-level (up to seven) observations made during a 30-day long MATERHORN field campaign in September-October 2012 allowed the study of temporal and spatial structure of katabatic flows in detail, and herein we report turbulence statistics (e.g., fluxes, variances, spectra, and cospectra) and their variations in katabatic flow. Observed vertical profiles show steep gradients near the surface, but in the layer above the slope jet the vertical variability is smaller. It is found that the vertical (normal to the slope) momentum flux and horizontal (along-slope) heat flux in a slope-following coordinate system change their sign below and above the wind maximum of a katabatic flow. The momentum flux is directed downward (upward) whereas the along-slope heat flux is downslope (upslope) below (above) the wind maximum. This suggests that the position of the jet-speed maximum can be obtained by linear interpolation between positive and negative values of the momentum flux (or the along-slope heat flux) to derive the height where the flux becomes zero. It is shown that the standard deviations of all wind-speed components (and therefore of the turbulent kinetic energy) and the dissipation rate of turbulent kinetic energy have a local minimum, whereas the standard deviation of air temperature has an absolute maximum at the height of wind-speed maximum. We report several cases when the destructive effect of vertical heat flux is completely cancelled by the generation of turbulence due to the along-slope heat flux. Turbulence above the wind
Spatio-temporal observations of tertiary ozone maximum
V. F. Sofieva
2009-03-01
Full Text Available We present spatio-temporal distributions of tertiary ozone maximum (TOM, based on GOMOS (Global Ozone Monitoring by Occultation of Stars ozone measurements in 2002–2006. The tertiary ozone maximum is typically observed in the high-latitude winter mesosphere at altitude ~72 km. Although the explanation for this phenomenon has been found recently – low concentrations of odd-hydrogen cause the subsequent decrease in odd-oxygen losses – models have had significant deviations from existing observations until recently. Good coverage of polar night regions by GOMOS data has allowed for the first time obtaining spatial and temporal observational distributions of night-time ozone mixing ratio in the mesosphere.
The distributions obtained from GOMOS data have specific features, which are variable from year to year. In particular, due to a long lifetime of ozone in polar night conditions, the downward transport of polar air by the meridional circulation is clearly observed in the tertiary ozone maximum time series. Although the maximum tertiary ozone mixing ratio is achieved close to the polar night terminator (as predicted by the theory, TOM can be observed also at very high latitudes, not only in the beginning and at the end, but also in the middle of winter. We have compared the observational spatio-temporal distributions of tertiary ozone maximum with that obtained using WACCM (Whole Atmosphere Community Climate Model and found that the specific features are reproduced satisfactorily by the model.
Since ozone in the mesosphere is very sensitive to HO_{x} concentrations, energetic particle precipitation can significantly modify the shape of the ozone profiles. In particular, GOMOS observations have shown that the tertiary ozone maximum was temporarily destroyed during the January 2005 and December 2006 solar proton events as a result of the HO_{x} enhancement from the increased ionization.
A dual method for maximum entropy restoration
Smith, C. B.
1979-01-01
A simple iterative dual algorithm for maximum entropy image restoration is presented. The dual algorithm involves fewer parameters than conventional minimization in the image space. Minicomputer test results for Fourier synthesis with inadequate phantom data are given.
Maximum Throughput in Multiple-Antenna Systems
Zamani, Mahdi
2012-01-01
The point-to-point multiple-antenna channel is investigated in uncorrelated block fading environment with Rayleigh distribution. The maximum throughput and maximum expected-rate of this channel are derived under the assumption that the transmitter is oblivious to the channel state information (CSI), however, the receiver has perfect CSI. First, we prove that in multiple-input single-output (MISO) channels, the optimum transmission strategy maximizing the throughput is to use all available antennas and perform equal power allocation with uncorrelated signals. Furthermore, to increase the expected-rate, multi-layer coding is applied. Analogously, we establish that sending uncorrelated signals and performing equal power allocation across all available antennas at each layer is optimum. A closed form expression for the maximum continuous-layer expected-rate of MISO channels is also obtained. Moreover, we investigate multiple-input multiple-output (MIMO) channels, and formulate the maximum throughput in the asympt...
Photoemission spectromicroscopy with MAXIMUM at Wisconsin
Ng, W.; Ray-Chaudhuri, A.K.; Cole, R.K.; Wallace, J.; Crossley, S.; Crossley, D.; Chen, G.; Green, M.; Guo, J.; Hansen, R.W.C.; Cerrina, F.; Margaritondo, G. (Dept. of Electrical Engineering, Dept. of Physics and Synchrotron Radiation Center, Univ. of Wisconsin, Madison (USA)); Underwood, J.H.; Korthright, J.; Perera, R.C.C. (Center for X-ray Optics, Accelerator and Fusion Research Div., Lawrence Berkeley Lab., CA (USA))
1990-06-01
We describe the development of the scanning photoemission spectromicroscope MAXIMUM at the Wisoncsin Synchrotron Radiation Center, which uses radiation from a 30-period undulator. The article includes a discussion of the first tests after the initial commissioning. (orig.).
Maximum-likelihood method in quantum estimation
Paris, M G A; Sacchi, M F
2001-01-01
The maximum-likelihood method for quantum estimation is reviewed and applied to the reconstruction of density matrix of spin and radiation as well as to the determination of several parameters of interest in quantum optics.
2011-03-24
... http://www.gsa.gov/relocationpolicy . Dated: March 21, 2011. Janet Dobbs, Director, Office of Travel... ADMINISTRATION Federal Travel Regulation (FTR); Relocation Allowances-- Relocation Income Tax Allowance (RITA... effective March 24, 2011. FOR FURTHER INFORMATION CONTACT: Mr. Ed Davis, Office of Governmentwide Policy...
2011-06-06
... Duty (TDY) Travel Allowances (Taxes); Relocation Allowances (Taxes) AGENCY: Office of Governmentwide... extended temporary duty (TDY) benefits to correct errors and to align that process with the proposed... incurred by employees as a result of relocation and to reimburse ``all'' of the taxes imposed on any...
19 CFR 114.23 - Maximum period.
2010-04-01
... 19 Customs Duties 1 2010-04-01 2010-04-01 false Maximum period. 114.23 Section 114.23 Customs... CARNETS Processing of Carnets § 114.23 Maximum period. (a) A.T.A. carnet. No A.T.A. carnet with a period of validity exceeding 1 year from date of issue shall be accepted. This period of validity cannot be...
Maximum-Likelihood Detection Of Noncoherent CPM
Divsalar, Dariush; Simon, Marvin K.
1993-01-01
Simplified detectors proposed for use in maximum-likelihood-sequence detection of symbols in alphabet of size M transmitted by uncoded, full-response continuous phase modulation over radio channel with additive white Gaussian noise. Structures of receivers derived from particular interpretation of maximum-likelihood metrics. Receivers include front ends, structures of which depends only on M, analogous to those in receivers of coherent CPM. Parts of receivers following front ends have structures, complexity of which would depend on N.
Training Concept, Evolution Time, and the Maximum Entropy Production Principle
Alexey Bezryadin
2016-04-01
Full Text Available The maximum entropy production principle (MEPP is a type of entropy optimization which demands that complex non-equilibrium systems should organize such that the rate of the entropy production is maximized. Our take on this principle is that to prove or disprove the validity of the MEPP and to test the scope of its applicability, it is necessary to conduct experiments in which the entropy produced per unit time is measured with a high precision. Thus we study electric-field-induced self-assembly in suspensions of carbon nanotubes and realize precise measurements of the entropy production rate (EPR. As a strong voltage is applied the suspended nanotubes merge together into a conducting cloud which produces Joule heat and, correspondingly, produces entropy. We introduce two types of EPR, which have qualitatively different significance: global EPR (g-EPR and the entropy production rate of the dissipative cloud itself (DC-EPR. The following results are obtained: (1 As the system reaches the maximum of the DC-EPR, it becomes stable because the applied voltage acts as a stabilizing thermodynamic potential; (2 We discover metastable states characterized by high, near-maximum values of the DC-EPR. Under certain conditions, such efficient entropy-producing regimes can only be achieved if the system is allowed to initially evolve under mildly non-equilibrium conditions, namely at a reduced voltage; (3 Without such a “training” period the system typically is not able to reach the allowed maximum of the DC-EPR if the bias is high; (4 We observe that the DC-EPR maximum is achieved within a time, Te, the evolution time, which scales as a power-law function of the applied voltage; (5 Finally, we present a clear example in which the g-EPR theoretical maximum can never be achieved. Yet, under a wide range of conditions, the system can self-organize and achieve a dissipative regime in which the DC-EPR equals its theoretical maximum.
SEXUAL DIMORPHISM OF MAXIMUM FEMORAL LENGTH
Pandya A M
2011-04-01
Full Text Available Sexual identification from the skeletal parts has medico legal and anthropological importance. Present study aims to obtain values of maximum femoral length and to evaluate its possible usefulness in determining correct sexual identification. Study sample consisted of 184 dry, normal, adult, human femora (136 male & 48 female from skeletal collections of Anatomy department, M. P. Shah Medical College, Jamnagar, Gujarat. Maximum length of femur was considered as maximum vertical distance between upper end of head of femur and the lowest point on femoral condyle, measured with the osteometric board. Mean Values obtained were, 451.81 and 417.48 for right male and female, and 453.35 and 420.44 for left male and female respectively. Higher value in male was statistically highly significant (P< 0.001 on both sides. Demarking point (D.P. analysis of the data showed that right femora with maximum length more than 476.70 were definitely male and less than 379.99 were definitely female; while for left bones, femora with maximum length more than 484.49 were definitely male and less than 385.73 were definitely female. Maximum length identified 13.43% of right male femora, 4.35% of right female femora, 7.25% of left male femora and 8% of left female femora. [National J of Med Res 2011; 1(2.000: 67-70
Low temperature catalytic combustion of natural gas - hydrogen - air mixtures
Newson, E.; Roth, F. von; Hottinger, P.; Truong, T.B. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)
1999-08-01
The low temperature catalytic combustion of natural gas - air mixtures would allow the development of no-NO{sub x} burners for heating and power applications. Using commercially available catalysts, the room temperature ignition of methane-propane-air mixtures has been shown in laboratory reactors with combustion efficiencies over 95% and maximum temperatures less than 700{sup o}C. After a 500 hour stability test, severe deactivation of both methane and propane oxidation functions was observed. In cooperation with industrial partners, scaleup to 3 kW is being investigated together with startup dynamics and catalyst stability. (author) 3 figs., 3 refs.
Maximum-Entropy Inference with a Programmable Annealer.
Chancellor, Nicholas; Szoke, Szilard; Vinci, Walter; Aeppli, Gabriel; Warburton, Paul A
2016-03-03
Optimisation problems typically involve finding the ground state (i.e. the minimum energy configuration) of a cost function with respect to many variables. If the variables are corrupted by noise then this maximises the likelihood that the solution is correct. The maximum entropy solution on the other hand takes the form of a Boltzmann distribution over the ground and excited states of the cost function to correct for noise. Here we use a programmable annealer for the information decoding problem which we simulate as a random Ising model in a field. We show experimentally that finite temperature maximum entropy decoding can give slightly better bit-error-rates than the maximum likelihood approach, confirming that useful information can be extracted from the excited states of the annealer. Furthermore we introduce a bit-by-bit analytical method which is agnostic to the specific application and use it to show that the annealer samples from a highly Boltzmann-like distribution. Machines of this kind are therefore candidates for use in a variety of machine learning applications which exploit maximum entropy inference, including language processing and image recognition.
Maximum-likelihood fits to histograms for improved parameter estimation
Fowler, Joseph W
2013-01-01
Straightforward methods for adapting the familiar chi^2 statistic to histograms of discrete events and other Poisson distributed data generally yield biased estimates of the parameters of a model. The bias can be important even when the total number of events is large. For the case of estimating a microcalorimeter's energy resolution at 6 keV from the observed shape of the Mn K-alpha fluorescence spectrum, a poor choice of chi^2 can lead to biases of at least 10% in the estimated resolution when up to thousands of photons are observed. The best remedy is a Poisson maximum-likelihood fit, through a simple modification of the standard Levenberg-Marquardt algorithm for chi^2 minimization. Where the modification is not possible, another approach allows iterative approximation of the maximum-likelihood fit.
Maximum work extraction and implementation costs for nonequilibrium Maxwell's demons
Sandberg, Henrik; Delvenne, Jean-Charles; Newton, Nigel J.; Mitter, Sanjoy K.
2014-10-01
We determine the maximum amount of work extractable in finite time by a demon performing continuous measurements on a quadratic Hamiltonian system subjected to thermal fluctuations, in terms of the information extracted from the system. The maximum work demon is found to apply a high-gain continuous feedback involving a Kalman-Bucy estimate of the system state and operates in nonequilibrium. A simple and concrete electrical implementation of the feedback protocol is proposed, which allows for analytic expressions of the flows of energy, entropy, and information inside the demon. This let us show that any implementation of the demon must necessarily include an external power source, which we prove both from classical thermodynamics arguments and from a version of Landauer's memory erasure argument extended to nonequilibrium linear systems.
$\\ell_0$-penalized maximum likelihood for sparse directed acyclic graphs
van de Geer, Sara
2012-01-01
We consider the problem of regularized maximum likelihood estimation for the structure and parameters of a high-dimensional, sparse directed acyclic graphical (DAG) model with Gaussian distribution, or equivalently, of a Gaussian structural equation model. We show that the $\\ell_0$-penalized maximum likelihood estimator of a DAG has about the same number of edges as the minimal-edge I-MAP (a DAG with minimal number of edges representing the distribution), and that it converges in Frobenius norm. We allow the number of nodes $p$ to be much larger than sample size $n$ but assume a sparsity condition and that any representation of the true DAG has at least a fixed proportion of its non-zero edge weights above the noise level. Our results do not rely on the restrictive strong faithfulness condition which is required for methods based on conditional independence testing such as the PC-algorithm.
Maximum disturbance review criteria : operational code and guideline
NONE
2003-07-01
This maximum disturbance review criteria (MDRC) is designed to encourage oil and gas construction contractors to reduce environmental impacts and consider land use and water management strategies in their development plans. The MDRC describes the preferred maximum disturbance allowances for the development of wellsites, access routes, right of way for pipelines and other associated facilities such as remote sumps, decking sites, camp sites and borrow pits. The guidelines specify acceptable parameters for typical oil and gas development activities. This report includes operating code tables which describe clearings and setbacks, access roads, watercourses, and photography and assessment reports for oil and gas activity. Additional care is required if special wildlife habitat features are encountered such as nesting sites, mineral licks, bear dens or beaver ponds. 4 tabs.
MaxOcc: a web portal for maximum occurrence analysis.
Bertini, Ivano; Ferella, Lucio; Luchinat, Claudio; Parigi, Giacomo; Petoukhov, Maxim V; Ravera, Enrico; Rosato, Antonio; Svergun, Dmitri I
2012-08-01
The MaxOcc web portal is presented for the characterization of the conformational heterogeneity of two-domain proteins, through the calculation of the Maximum Occurrence that each protein conformation can have in agreement with experimental data. Whatever the real ensemble of conformations sampled by a protein, the weight of any conformation cannot exceed the calculated corresponding Maximum Occurrence value. The present portal allows users to compute these values using any combination of restraints like pseudocontact shifts, paramagnetism-based residual dipolar couplings, paramagnetic relaxation enhancements and small angle X-ray scattering profiles, given the 3D structure of the two domains as input. MaxOcc is embedded within the NMR grid services of the WeNMR project and is available via the WeNMR gateway at http://py-enmr.cerm.unifi.it/access/index/maxocc . It can be used freely upon registration to the grid with a digital certificate.
REACTOR PRESSURE VESSEL TEMPERATURE ANALYSIS OF CANDIDATE VERY HIGH TEMPERATURE REACTOR DESIGNS
Hans D. Gougar; Cliff B. Davis; George Hayner; Kevan Weaver
2006-10-01
Analyses were performed to determine maximum temperatures in the reactor pressure vessel for two potential Very-High Temperature Reactor (VHTR) designs during normal operation and during a depressurized conduction cooldown accident. The purpose of the analyses was to aid in the determination of appropriate reactor vessel materials for the VHTR. The designs evaluated utilized both prismatic and pebble-bed cores that generated 600 MW of thermal power. Calculations were performed for fluid outlet temperatures of 900 and 950 °C, corresponding to the expected range for the VHTR. The analyses were performed using the RELAP5-3D and PEBBED-THERMIX computer codes. Results of the calculations were compared with preliminary temperature limits derived from the ASME pressure vessel code. Because PEBBED-THERMIX has not been extensively validated, confirmatory calculations were also performed with RELAP5-3D for the pebble-bed design. During normal operation, the predicted axial profiles in reactor vessel temperature were similar with both codes and the predicted maximum values were within 2 °C. The trends of the calculated vessel temperatures were similar during the depressurized conduction cooldown accident. The maximum value predicted with RELAP5-3D during the depressurized conduction cooldown accident was about 40 °C higher than that predicted with PEBBED. This agreement is considered reasonable based on the expected uncertainty in either calculation. The differences between the PEBBED and RELAP5-3D calculations were not large enough to affect conclusions concerning comparisons between calculated and allowed maximum temperatures during normal operation and the depressurized conduction cooldown accident.
The maximum rotation of a galactic disc
Bottema, R
1997-01-01
The observed stellar velocity dispersions of galactic discs show that the maximum rotation of a disc is on average 63% of the observed maximum rotation. This criterion can, however, not be applied to small or low surface brightness (LSB) galaxies because such systems show, in general, a continuously rising rotation curve until the outermost measured radial position. That is why a general relation has been derived, giving the maximum rotation for a disc depending on the luminosity, surface brightness, and colour of the disc. As a physical basis of this relation serves an adopted fixed mass-to-light ratio as a function of colour. That functionality is consistent with results from population synthesis models and its absolute value is determined from the observed stellar velocity dispersions. The derived maximum disc rotation is compared with a number of observed maximum rotations, clearly demonstrating the need for appreciable amounts of dark matter in the disc region and even more so for LSB galaxies. Matters h...
Maximum permissible voltage of YBCO coated conductors
Wen, J.; Lin, B.; Sheng, J.; Xu, J.; Jin, Z.; Hong, Z.; Wang, D.; Zhou, H.; Shen, X.; Shen, C.
2014-06-01
Superconducting fault current limiter (SFCL) could reduce short circuit currents in electrical power system. One of the most important thing in developing SFCL is to find out the maximum permissible voltage of each limiting element. The maximum permissible voltage is defined as the maximum voltage per unit length at which the YBCO coated conductors (CC) do not suffer from critical current (Ic) degradation or burnout. In this research, the time of quenching process is changed and voltage is raised until the Ic degradation or burnout happens. YBCO coated conductors test in the experiment are from American superconductor (AMSC) and Shanghai Jiao Tong University (SJTU). Along with the quenching duration increasing, the maximum permissible voltage of CC decreases. When quenching duration is 100 ms, the maximum permissible of SJTU CC, 12 mm AMSC CC and 4 mm AMSC CC are 0.72 V/cm, 0.52 V/cm and 1.2 V/cm respectively. Based on the results of samples, the whole length of CCs used in the design of a SFCL can be determined.
Computing Rooted and Unrooted Maximum Consistent Supertrees
van Iersel, Leo
2009-01-01
A chief problem in phylogenetics and database theory is the computation of a maximum consistent tree from a set of rooted or unrooted trees. A standard input are triplets, rooted binary trees on three leaves, or quartets, unrooted binary trees on four leaves. We give exact algorithms constructing rooted and unrooted maximum consistent supertrees in time O(2^n n^5 m^2 log(m)) for a set of m triplets (quartets), each one distinctly leaf-labeled by some subset of n labels. The algorithms extend to weighted triplets (quartets). We further present fast exact algorithms for constructing rooted and unrooted maximum consistent trees in polynomial space. Finally, for a set T of m rooted or unrooted trees with maximum degree D and distinctly leaf-labeled by some subset of a set L of n labels, we compute, in O(2^{mD} n^m m^5 n^6 log(m)) time, a tree distinctly leaf-labeled by a maximum-size subset X of L that all trees in T, when restricted to X, are consistent with.
Maximum magnitude earthquakes induced by fluid injection
McGarr, Arthur F.
2014-01-01
Analysis of numerous case histories of earthquake sequences induced by fluid injection at depth reveals that the maximum magnitude appears to be limited according to the total volume of fluid injected. Similarly, the maximum seismic moment seems to have an upper bound proportional to the total volume of injected fluid. Activities involving fluid injection include (1) hydraulic fracturing of shale formations or coal seams to extract gas and oil, (2) disposal of wastewater from these gas and oil activities by injection into deep aquifers, and (3) the development of enhanced geothermal systems by injecting water into hot, low-permeability rock. Of these three operations, wastewater disposal is observed to be associated with the largest earthquakes, with maximum magnitudes sometimes exceeding 5. To estimate the maximum earthquake that could be induced by a given fluid injection project, the rock mass is assumed to be fully saturated, brittle, to respond to injection with a sequence of earthquakes localized to the region weakened by the pore pressure increase of the injection operation and to have a Gutenberg-Richter magnitude distribution with a b value of 1. If these assumptions correctly describe the circumstances of the largest earthquake, then the maximum seismic moment is limited to the volume of injected liquid times the modulus of rigidity. Observations from the available case histories of earthquakes induced by fluid injection are consistent with this bound on seismic moment. In view of the uncertainties in this analysis, however, this should not be regarded as an absolute physical limit.
Maximum magnitude earthquakes induced by fluid injection
McGarr, A.
2014-02-01
Analysis of numerous case histories of earthquake sequences induced by fluid injection at depth reveals that the maximum magnitude appears to be limited according to the total volume of fluid injected. Similarly, the maximum seismic moment seems to have an upper bound proportional to the total volume of injected fluid. Activities involving fluid injection include (1) hydraulic fracturing of shale formations or coal seams to extract gas and oil, (2) disposal of wastewater from these gas and oil activities by injection into deep aquifers, and (3) the development of enhanced geothermal systems by injecting water into hot, low-permeability rock. Of these three operations, wastewater disposal is observed to be associated with the largest earthquakes, with maximum magnitudes sometimes exceeding 5. To estimate the maximum earthquake that could be induced by a given fluid injection project, the rock mass is assumed to be fully saturated, brittle, to respond to injection with a sequence of earthquakes localized to the region weakened by the pore pressure increase of the injection operation and to have a Gutenberg-Richter magnitude distribution with a b value of 1. If these assumptions correctly describe the circumstances of the largest earthquake, then the maximum seismic moment is limited to the volume of injected liquid times the modulus of rigidity. Observations from the available case histories of earthquakes induced by fluid injection are consistent with this bound on seismic moment. In view of the uncertainties in this analysis, however, this should not be regarded as an absolute physical limit.
Commercial Platforms Allow Affordable Space Research
2013-01-01
At an altitude of about 240 miles, its orbital path carries it over 90 percent of the Earth s population. It circles the Earth in continuous free fall; its crew of six and one Robonaut pass the days, experiencing 16 sunrises and 16 sunsets every 24 hours, in microgravity, an environment in which everything from bodily functions to the physical behavior of materials changes drastically from what is common on the ground. Outside its shielded confines, temperatures cycle from one extreme to the other, radiation is rampant, and atomic oxygen corrodes everything it touches. A unique feat of engineering, the International Space Station (ISS) also represents the most remarkable platform for scientific research ever devised. In 2005, anticipating the space station s potential for NASA and non-NASA scientists alike, the NASA Authorization Act designated the US segment of the ISS as a national laboratory, instructing the Agency to "increase the utilization of the ISS by other Federal entities and the private sector." With the ISS set to maintain operations through at least 2020, the station offers an unprecedented long-term access to space conditions, enabling research not previously possible. "There will be new drug discoveries, new pharmaceuticals, a better understanding of how we affect the planet and how we can maintain it," says Marybeth Edeen, the ISS National Laboratory manager, based at Johnson Space Center. The ISS, she says, represents a major example of the government s role in making such advancements possible. "The government is key in that researchers cannot afford to build the kind of infrastructure that the government can provide. But we then have to make that infrastructure available at a reasonable cost." Enter Jeff Manber, who saw in the ISS National Lab an extraordinary opportunity to advance science, education, and business in ways never before seen.
Probabilistic maximum-value wind prediction for offshore environments
Staid, Andrea; Pinson, Pierre; Guikema, Seth D.
2015-01-01
, and probabilistic forecasts result in greater value to the end-user. The models outperform traditional baseline forecast methods and achieve low predictive errors on the order of 1–2 m s−1. We show the results of their predictive accuracy for different lead times and different training methodologies....... statistical models to predict the full distribution of the maximum-value wind speeds in a 3 h interval. We take a detailed look at the performance of linear models, generalized additive models and multivariate adaptive regression splines models using meteorological covariates such as gust speed, wind speed......, convective available potential energy, Charnock, mean sea-level pressure and temperature, as given by the European Center for Medium-Range Weather Forecasts forecasts. The models are trained to predict the mean value of maximum wind speed, and the residuals from training the models are used to develop...
Maximum Multiflow in Wireless Network Coding
Zhou, Jin-Yi; Jiang, Yong; Zheng, Hai-Tao
2012-01-01
In a multihop wireless network, wireless interference is crucial to the maximum multiflow (MMF) problem, which studies the maximum throughput between multiple pairs of sources and sinks. In this paper, we observe that network coding could help to decrease the impacts of wireless interference, and propose a framework to study the MMF problem for multihop wireless networks with network coding. Firstly, a network model is set up to describe the new conflict relations modified by network coding. Then, we formulate a linear programming problem to compute the maximum throughput and show its superiority over one in networks without coding. Finally, the MMF problem in wireless network coding is shown to be NP-hard and a polynomial approximation algorithm is proposed.
Payoff-monotonic game dynamics and the maximum clique problem.
Pelillo, Marcello; Torsello, Andrea
2006-05-01
Evolutionary game-theoretic models and, in particular, the so-called replicator equations have recently proven to be remarkably effective at approximately solving the maximum clique and related problems. The approach is centered around a classic result from graph theory that formulates the maximum clique problem as a standard (continuous) quadratic program and exploits the dynamical properties of these models, which, under a certain symmetry assumption, possess a Lyapunov function. In this letter, we generalize previous work along these lines in several respects. We introduce a wide family of game-dynamic equations known as payoff-monotonic dynamics, of which replicator dynamics are a special instance, and show that they enjoy precisely the same dynamical properties as standard replicator equations. These properties make any member of this family a potential heuristic for solving standard quadratic programs and, in particular, the maximum clique problem. Extensive simulations, performed on random as well as DIMACS benchmark graphs, show that this class contains dynamics that are considerably faster than and at least as accurate as replicator equations. One problem associated with these models, however, relates to their inability to escape from poor local solutions. To overcome this drawback, we focus on a particular subclass of payoff-monotonic dynamics used to model the evolution of behavior via imitation processes and study the stability of their equilibria when a regularization parameter is allowed to take on negative values. A detailed analysis of these properties suggests a whole class of annealed imitation heuristics for the maximum clique problem, which are based on the idea of varying the parameter during the imitation optimization process in a principled way, so as to avoid unwanted inefficient solutions. Experiments show that the proposed annealing procedure does help to avoid poor local optima by initially driving the dynamics toward promising regions in
The Wiener maximum quadratic assignment problem
Cela, Eranda; Woeginger, Gerhard J
2011-01-01
We investigate a special case of the maximum quadratic assignment problem where one matrix is a product matrix and the other matrix is the distance matrix of a one-dimensional point set. We show that this special case, which we call the Wiener maximum quadratic assignment problem, is NP-hard in the ordinary sense and solvable in pseudo-polynomial time. Our approach also yields a polynomial time solution for the following problem from chemical graph theory: Find a tree that maximizes the Wiener index among all trees with a prescribed degree sequence. This settles an open problem from the literature.
Maximum floodflows in the conterminous United States
Crippen, John R.; Bue, Conrad D.
1977-01-01
Peak floodflows from thousands of observation sites within the conterminous United States were studied to provide a guide for estimating potential maximum floodflows. Data were selected from 883 sites with drainage areas of less than 10,000 square miles (25,900 square kilometers) and were grouped into regional sets. Outstanding floods for each region were plotted on graphs, and envelope curves were computed that offer reasonable limits for estimates of maximum floods. The curves indicate that floods may occur that are two to three times greater than those known for most streams.
Revealing the Maximum Strength in Nanotwinned Copper
Lu, L.; Chen, X.; Huang, Xiaoxu
2009-01-01
The strength of polycrystalline materials increases with decreasing grain size. Below a critical size, smaller grains might lead to softening, as suggested by atomistic simulations. The strongest size should arise at a transition in deformation mechanism from lattice dislocation activities to grain...... boundary–related processes. We investigated the maximum strength of nanotwinned copper samples with different twin thicknesses. We found that the strength increases with decreasing twin thickness, reaching a maximum at 15 nanometers, followed by a softening at smaller values that is accompanied by enhanced...
The Maximum Resource Bin Packing Problem
Boyar, J.; Epstein, L.; Favrholdt, L.M.
2006-01-01
Usually, for bin packing problems, we try to minimize the number of bins used or in the case of the dual bin packing problem, maximize the number or total size of accepted items. This paper presents results for the opposite problems, where we would like to maximize the number of bins used...... algorithms, First-Fit-Increasing and First-Fit-Decreasing for the maximum resource variant of classical bin packing. For the on-line variant, we define maximum resource variants of classical and dual bin packing. For dual bin packing, no on-line algorithm is competitive. For classical bin packing, we find...
Maximum entropy analysis of EGRET data
Pohl, M.; Strong, A.W.
1997-01-01
EGRET data are usually analysed on the basis of the Maximum-Likelihood method \\cite{ma96} in a search for point sources in excess to a model for the background radiation (e.g. \\cite{hu97}). This method depends strongly on the quality of the background model, and thus may have high systematic unce...... uncertainties in region of strong and uncertain background like the Galactic Center region. Here we show images of such regions obtained by the quantified Maximum-Entropy method. We also discuss a possible further use of MEM in the analysis of problematic regions of the sky....
Revealing the Maximum Strength in Nanotwinned Copper
Lu, L.; Chen, X.; Huang, Xiaoxu
2009-01-01
The strength of polycrystalline materials increases with decreasing grain size. Below a critical size, smaller grains might lead to softening, as suggested by atomistic simulations. The strongest size should arise at a transition in deformation mechanism from lattice dislocation activities to grain...... boundary–related processes. We investigated the maximum strength of nanotwinned copper samples with different twin thicknesses. We found that the strength increases with decreasing twin thickness, reaching a maximum at 15 nanometers, followed by a softening at smaller values that is accompanied by enhanced...
Maximum phytoplankton concentrations in the sea
Jackson, G.A.; Kiørboe, Thomas
2008-01-01
A simplification of plankton dynamics using coagulation theory provides predictions of the maximum algal concentration sustainable in aquatic systems. These predictions have previously been tested successfully against results from iron fertilization experiments. We extend the test to data collected...... in the North Atlantic as part of the Bermuda Atlantic Time Series program as well as data collected off Southern California as part of the Southern California Bight Study program. The observed maximum particulate organic carbon and volumetric particle concentrations are consistent with the predictions...
Extracting volatility signal using maximum a posteriori estimation
Neto, David
2016-11-01
This paper outlines a methodology to estimate a denoised volatility signal for foreign exchange rates using a hidden Markov model (HMM). For this purpose a maximum a posteriori (MAP) estimation is performed. A double exponential prior is used for the state variable (the log-volatility) in order to allow sharp jumps in realizations and then log-returns marginal distributions with heavy tails. We consider two routes to choose the regularization and we compare our MAP estimate to realized volatility measure for three exchange rates.
A Maximum Entropy Modelling of the Rain Drop Size Distribution
Francisco J. Tapiador
2011-01-01
Full Text Available This paper presents a maximum entropy approach to Rain Drop Size Distribution (RDSD modelling. It is shown that this approach allows (1 to use a physically consistent rationale to select a particular probability density function (pdf (2 to provide an alternative method for parameter estimation based on expectations of the population instead of sample moments and (3 to develop a progressive method of modelling by updating the pdf as new empirical information becomes available. The method is illustrated with both synthetic and real RDSD data, the latest coming from a laser disdrometer network specifically designed to measure the spatial variability of the RDSD.
Implementation of the Maximum Entropy Method for Analytic Continuation
Levy, Ryan; Gull, Emanuel
2016-01-01
We present $\\texttt{Maxent}$, a tool for performing analytic continuation of spectral functions using the maximum entropy method. The code operates on discrete imaginary axis datasets (values with uncertainties) and transforms this input to the real axis. The code works for imaginary time and Matsubara frequency data and implements the 'Legendre' representation of finite temperature Green's functions. It implements a variety of kernels, default models, and grids for continuing bosonic, fermionic, anomalous, and other data. Our implementation is licensed under GPLv2 and extensively documented. This paper shows the use of the programs in detail.
Implementation of the maximum entropy method for analytic continuation
Levy, Ryan; LeBlanc, J. P. F.; Gull, Emanuel
2017-06-01
We present Maxent, a tool for performing analytic continuation of spectral functions using the maximum entropy method. The code operates on discrete imaginary axis datasets (values with uncertainties) and transforms this input to the real axis. The code works for imaginary time and Matsubara frequency data and implements the 'Legendre' representation of finite temperature Green's functions. It implements a variety of kernels, default models, and grids for continuing bosonic, fermionic, anomalous, and other data. Our implementation is licensed under GPLv3 and extensively documented. This paper shows the use of the programs in detail.
Analysis of Photovoltaic Maximum Power Point Trackers
Veerachary, Mummadi
The photovoltaic generator exhibits a non-linear i-v characteristic and its maximum power point (MPP) varies with solar insolation. An intermediate switch-mode dc-dc converter is required to extract maximum power from the photovoltaic array. In this paper buck, boost and buck-boost topologies are considered and a detailed mathematical analysis, both for continuous and discontinuous inductor current operation, is given for MPP operation. The conditions on the connected load values and duty ratio are derived for achieving the satisfactory maximum power point operation. Further, it is shown that certain load values, falling out of the optimal range, will drive the operating point away from the true maximum power point. Detailed comparison of various topologies for MPPT is given. Selection of the converter topology for a given loading is discussed. Detailed discussion on circuit-oriented model development is given and then MPPT effectiveness of various converter systems is verified through simulations. Proposed theory and analysis is validated through experimental investigations.
On maximum cycle packings in polyhedral graphs
Peter Recht
2014-04-01
Full Text Available This paper addresses upper and lower bounds for the cardinality of a maximum vertex-/edge-disjoint cycle packing in a polyhedral graph G. Bounds on the cardinality of such packings are provided, that depend on the size, the order or the number of faces of G, respectively. Polyhedral graphs are constructed, that attain these bounds.
Hard graphs for the maximum clique problem
Hoede, Cornelis
1988-01-01
The maximum clique problem is one of the NP-complete problems. There are graphs for which a reduction technique exists that transforms the problem for these graphs into one for graphs with specific properties in polynomial time. The resulting graphs do not grow exponentially in order and number. Gra
Maximum Likelihood Estimation of Search Costs
J.L. Moraga-Gonzalez (José Luis); M.R. Wildenbeest (Matthijs)
2006-01-01
textabstractIn a recent paper Hong and Shum (forthcoming) present a structural methodology to estimate search cost distributions. We extend their approach to the case of oligopoly and present a maximum likelihood estimate of the search cost distribution. We apply our method to a data set of online p
Weak Scale From the Maximum Entropy Principle
Hamada, Yuta; Kawana, Kiyoharu
2015-01-01
The theory of multiverse and wormholes suggests that the parameters of the Standard Model are fixed in such a way that the radiation of the $S^{3}$ universe at the final stage $S_{rad}$ becomes maximum, which we call the maximum entropy principle. Although it is difficult to confirm this principle generally, for a few parameters of the Standard Model, we can check whether $S_{rad}$ actually becomes maximum at the observed values. In this paper, we regard $S_{rad}$ at the final stage as a function of the weak scale ( the Higgs expectation value ) $v_{h}$, and show that it becomes maximum around $v_{h}={\\cal{O}}(300\\text{GeV})$ when the dimensionless couplings in the Standard Model, that is, the Higgs self coupling, the gauge couplings, and the Yukawa couplings are fixed. Roughly speaking, we find that the weak scale is given by \\begin{equation} v_{h}\\sim\\frac{T_{BBN}^{2}}{M_{pl}y_{e}^{5}},\
Global characterization of the Holocene Thermal Maximum
Renssen, H.; Seppä, H.; Crosta, X.; Goosse, H.; Roche, D.M.V.A.P.
2012-01-01
We analyze the global variations in the timing and magnitude of the Holocene Thermal Maximum (HTM) and their dependence on various forcings in transient simulations covering the last 9000 years (9 ka), performed with a global atmosphere-ocean-vegetation model. In these experiments, we consider the i
Instance Optimality of the Adaptive Maximum Strategy
L. Diening; C. Kreuzer; R. Stevenson
2016-01-01
In this paper, we prove that the standard adaptive finite element method with a (modified) maximum marking strategy is instance optimal for the total error, being the square root of the squared energy error plus the squared oscillation. This result will be derived in the model setting of Poisson’s e
Maximum phonation time: variability and reliability.
Speyer, Renée; Bogaardt, Hans C A; Passos, Valéria Lima; Roodenburg, Nel P H D; Zumach, Anne; Heijnen, Mariëlle A M; Baijens, Laura W J; Fleskens, Stijn J H M; Brunings, Jan W
2010-05-01
The objective of the study was to determine maximum phonation time reliability as a function of the number of trials, days, and raters in dysphonic and control subjects. Two groups of adult subjects participated in this reliability study: a group of outpatients with functional or organic dysphonia versus a group of healthy control subjects matched by age and gender. Over a period of maximally 6 weeks, three video recordings were made of five subjects' maximum phonation time trials. A panel of five experts were responsible for all measurements, including a repeated measurement of the subjects' first recordings. Patients showed significantly shorter maximum phonation times compared with healthy controls (on average, 6.6 seconds shorter). The averaged interclass correlation coefficient (ICC) over all raters per trial for the first day was 0.998. The averaged reliability coefficient per rater and per trial for repeated measurements of the first day's data was 0.997, indicating high intrarater reliability. The mean reliability coefficient per day for one trial was 0.939. When using five trials, the reliability increased to 0.987. The reliability over five trials for a single day was 0.836; for 2 days, 0.911; and for 3 days, 0.935. To conclude, the maximum phonation time has proven to be a highly reliable measure in voice assessment. A single rater is sufficient to provide highly reliable measurements.
Maximum Phonation Time: Variability and Reliability
R. Speyer; H.C.A. Bogaardt; V.L. Passos; N.P.H.D. Roodenburg; A. Zumach; M.A.M. Heijnen; L.W.J. Baijens; S.J.H.M. Fleskens; J.W. Brunings
2010-01-01
The objective of the study was to determine maximum phonation time reliability as a function of the number of trials, days, and raters in dysphonic and control subjects. Two groups of adult subjects participated in this reliability study: a group of outpatients with functional or organic dysphonia v
Maximum likelihood estimation of fractionally cointegrated systems
Lasak, Katarzyna
In this paper we consider a fractionally cointegrated error correction model and investigate asymptotic properties of the maximum likelihood (ML) estimators of the matrix of the cointe- gration relations, the degree of fractional cointegration, the matrix of the speed of adjustment...
Maximum likelihood estimation for integrated diffusion processes
Baltazar-Larios, Fernando; Sørensen, Michael
EM-algorithm to obtain maximum likelihood estimates of the parameters in the diffusion model. As part of the algorithm, we use a recent simple method for approximate simulation of diffusion bridges. In simulation studies for the Ornstein-Uhlenbeck process and the CIR process the proposed method works...
Maximum gain of Yagi-Uda arrays
Bojsen, J.H.; Schjær-Jacobsen, Hans; Nilsson, E.
1971-01-01
Numerical optimisation techniques have been used to find the maximum gain of some specific parasitic arrays. The gain of an array of infinitely thin, equispaced dipoles loaded with arbitrary reactances has been optimised. The results show that standard travelling-wave design methods are not optimum....... Yagi–Uda arrays with equal and unequal spacing have also been optimised with experimental verification....
Electronic Structure and Maximum Energy Product of MnBi
Jihoon Park
2014-08-01
Full Text Available We have performed first-principles calculations to obtain magnetic moment, magnetocrystalline anisotropy energy (MAE, i.e., the magnetic crystalline anisotropy constant (K, and the Curie temperature (Tc of low temperature phase (LTP MnBi and also estimated the maximum energy product (BHmax at elevated temperatures. The full-potential linearized augmented plane wave (FPLAPW method, based on density functional theory (DFT within the local spin density approximation (LSDA, was used to calculate the electronic structure of LPM MnBi. The Tc was calculated by the mean field theory. The calculated magnetic moment, MAE, and Tc are 3.63 μB/f.u. (formula unit (79 emu/g or 714 emu/cm3, −0.163 meV/u.c. (or K = −0.275 × 106 J/m3 and 711 K, respectively. The (BHmax at the elevated temperatures was estimated by combining experimental coercivity (Hci and the temperature dependence of magnetization (Ms(T. The (BHmax is 17.7 MGOe at 300 K, which is in good agreement with the experimental result for directionally-solidified LTP MnBi (17 MGOe. In addition, a study of electron density maps and the lattice constant c/a ratio dependence of the magnetic moment suggested that doping of a third element into interstitial sites of LTP MnBi can increase the Ms.
Rotating proto-neutron stars: spin evolution, maximum mass and I-Love-Q relations
Martinon, Grégoire; Gualtieri, Leonardo; Ferrari, Valeria
2014-01-01
Shortly after its birth in a gravitational collapse, a proto-neutron star enters in a phase of quasi-stationary evolution characterized by large gradients of the thermodynamical variables and intense neutrino emission. In few tens of seconds the gradients smooth out while the star contracts and cools down, until it becomes a neutron star. In this paper we study this phase of the proto-neutron star life including rotation, and employing finite temperature equations of state. We model the evolution of the rotation rate, and determine the relevant quantities characterizing the star. Our results show that an isolated neutron star cannot reach, at the end of the evolution, the maximum values of mass and rotation rate allowed by the zero-temperature equation of state. Moreover, a mature neutron star evolved in isolation cannot rotate too rapidly, even if it is born from a proto-neutron star rotating at the mass-shedding limit. We also show that the I-Love-Q relations are violated in the first second of life, but th...
Genei Antonio Dalmago
2006-06-01
Full Text Available Um experimento foi conduzido para avaliar a relação da evapotranspiração máxima (ETm da cultura de pimentão por unidade de índice de área foliar (ETmf com a radiação solar global incidente (Rg e e saldo de radiação (Rn e, externos à estufa, e com a temperatura (t am, umidade relativa (URm e déficit de saturação (D do ar no interior da estufa. A ETm foi determinada por lisimetria. Apenas a temperatura e a umidade relativa do ar foram registradas e as demais variáveis foram estimadas. O Rn e apresentou o maior efeito isolado, seguido pelo D e pela URm. A temperatura do ar às 15 horas e a temperatura máxima diária foram as variáveis pontuais de maior associação com a ETmf. A Rg e melhorou sua relação quando analisada em diferentes faixas de t am. Os resultados confirmaram o Rn e e o D como as variáveis meteorológicas de maior efeito preditivo da evapotranspiração das culturas em estufas plásticas no outono, porém com graus diferenciados de ajuste para o pimentão em relação às outras culturas.An experiment was carried out to study the relationship between sweet pepper maximum evapotranspiration (ETm per unit leaf area index (ETmf and incident solar radiation (Rg e and net radiation (Rn e outside greenhouse, and with air temperature (t am, air relative humidity (URm and water vapor pressure deficit (D inside a greenhouse. ETm was measured by lysimeters. Temperature and relative humidity were registered whereas Rg e and Rn e were estimated. The Rn e was the variable with laRg e st effect on ETmf determination, followed by D and URm. The air temperature at 15:00 and the daily maximum temperature were variables of laRg e r association with ETmf among the variables with punctual time observations. Rg e improved its relationship with ETmf when was analyzed with different t am ranges. The results confirmed Rn e and D as the meteorological variables of highest relationship with evapotranspiration in plastic greenhouse
BINDER DRAINAGE TEST FOR POROUS MIXTURES MADE BY VARYING THE MAXIMUM AGGREGATE SIZES
Hardiman Hardiman
2004-01-01
Full Text Available Binder drainage occurs with mixes of small aggregate surface area particularly porous asphalt. The binder drainage test, developed by the Transport Research Laboratory, UK, is commonly used to set an upper limit on the acceptable binder content for a porous mix. This paper presents the results of a laboratory investigation to determine the effects of different binder types on the binder drainage characteristics of porous mix made of various maximum aggregate sizes 20, 14 and 10 mm. Two types of binder were used, conventional 60/70 pen bitumen, and styrene butadiene styrene (SBS modified bitumen. The amount of binder lost through drainage after three hours at the maximum mixing temperature were measured in duplicate for mixes of different maximum sizes and binder contents. The maximum mixing temperature adopted depends on the types of binder used. The retained binder is plotted against the initial mixed binder content, together with the line of equality where the retained binder equals the mixed binder content. The results indicate the significant contribution of using SBS modified bitumen to increase the target bitumen binder content. Their significance is discussed in terms of target binder content, the critical binder content, the maximum mixed binder content and the maximum retained binder content values obtained from the binder drainage test. It was concluded that increasing maximum aggregate sizes decrease the maximum retained binder content, critical binder content, target binder content, maximum mixed binder content, and mixed content for both binders, but however for all mixtures, SBS is the highest.
Venus atmosphere profile from a maximum entropy principle
L. N. Epele
2007-10-01
Full Text Available The variational method with constraints recently developed by Verkley and Gerkema to describe maximum-entropy atmospheric profiles is generalized to ideal gases but with temperature-dependent specific heats. In so doing, an extended and non standard potential temperature is introduced that is well suited for tackling the problem under consideration. This new formalism is successfully applied to the atmosphere of Venus. Three well defined regions emerge in this atmosphere up to a height of 100 km from the surface: the lowest one up to about 35 km is adiabatic, a transition layer located at the height of the cloud deck and finally a third region which is practically isothermal.
Maximum Entropy Production and Non-Gaussian Climate Variability
Sura, Philip
2016-01-01
Earth's atmosphere is in a state far from thermodynamic equilibrium. For example, the large scale equator-to-pole temperature gradient is maintained by tropical heating, polar cooling, and a midlatitude meridional eddy heat flux predominantly driven by baroclinically unstable weather systems. Based on basic thermodynamic principles, it can be shown that the meridional heat flux, in combination with the meridional temperature gradient, acts to maximize entropy production of the atmosphere. In fact, maximum entropy production (MEP) has been successfully used to explain the observed mean state of the atmosphere and other components of the climate system. However, one important feature of the large scale atmospheric circulation is its often non-Gaussian variability about the mean. This paper presents theoretical and observational evidence that some processes in the midlatitude atmosphere are significantly non-Gaussian to maximize entropy production. First, after introducing the basic theory, it is shown that the ...
Maximum mass, moment of inertia and compactness of relativistic stars
Breu, Cosima
2016-01-01
A number of recent works have highlighted that it is possible to express the properties of general-relativistic stellar equilibrium configurations in terms of functions that do not depend on the specific equation of state employed to describe matter at nuclear densities. These functions are normally referred to as "universal relations" and have been found to apply, within limits, both to static or stationary isolated stars, as well as to fully dynamical and merging binary systems. Further extending the idea that universal relations can be valid also away from stability, we show that a universal relation is exhibited also by equilibrium solutions that are not stable. In particular, the mass of rotating configurations on the turning-point line shows a universal behaviour when expressed in terms of the normalised Keplerian angular momentum. In turn, this allows us to compute the maximum mass allowed by uniform rotation, M_{max}, simply in terms of the maximum mass of the nonrotating configuration, M_{TOV}, findi...
MAXIMUM POWEWR POINT TRACKING SYSTEM FOR PHOTOVOLTAIC STATION: A REVIEW
I. Elzein
2015-01-01
Full Text Available In recent years there has been a growing attention towards the use of renewable energy sources. Among them solar energy is one of the most promising green energy resources due to its environment sustainability and inexhaustibility. However photovoltaic systems (PhV suffer from big cost of equipment and low efficiency. Moreover, the solar cell V-I characteristic is nonlinear and varies with irradiation and temperature. In general, there is a unique point of PhV operation, called the Maximum Power Point (MPP, in which the PV system operates with maximum efficiency and produces its maximum output power. The location of the MPP is not known in advance, but can be located, either through calculation models or by search algorithms. Therefore MPPT techniques are important to maintain the PV array’s high efficiency. Many different techniques for MPPT are discussed. This review paper hopefully will serve as a convenient tool for future work in PhV power conversion.
40 CFR 73.21 - Phase II repowering allowances.
2010-07-01
... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Phase II repowering allowances. 73.21... (CONTINUED) SULFUR DIOXIDE ALLOWANCE SYSTEM Allowance Allocations § 73.21 Phase II repowering allowances. (a) Repowering allowances. In addition to allowances allocated under § 73.10(b), the Administrator will...
Model Selection Through Sparse Maximum Likelihood Estimation
Banerjee, Onureena; D'Aspremont, Alexandre
2007-01-01
We consider the problem of estimating the parameters of a Gaussian or binary distribution in such a way that the resulting undirected graphical model is sparse. Our approach is to solve a maximum likelihood problem with an added l_1-norm penalty term. The problem as formulated is convex but the memory requirements and complexity of existing interior point methods are prohibitive for problems with more than tens of nodes. We present two new algorithms for solving problems with at least a thousand nodes in the Gaussian case. Our first algorithm uses block coordinate descent, and can be interpreted as recursive l_1-norm penalized regression. Our second algorithm, based on Nesterov's first order method, yields a complexity estimate with a better dependence on problem size than existing interior point methods. Using a log determinant relaxation of the log partition function (Wainwright & Jordan (2006)), we show that these same algorithms can be used to solve an approximate sparse maximum likelihood problem for...
Maximum-entropy description of animal movement.
Fleming, Chris H; Subaşı, Yiğit; Calabrese, Justin M
2015-03-01
We introduce a class of maximum-entropy states that naturally includes within it all of the major continuous-time stochastic processes that have been applied to animal movement, including Brownian motion, Ornstein-Uhlenbeck motion, integrated Ornstein-Uhlenbeck motion, a recently discovered hybrid of the previous models, and a new model that describes central-place foraging. We are also able to predict a further hierarchy of new models that will emerge as data quality improves to better resolve the underlying continuity of animal movement. Finally, we also show that Langevin equations must obey a fluctuation-dissipation theorem to generate processes that fall from this class of maximum-entropy distributions when the constraints are purely kinematic.
Maximum Variance Hashing via Column Generation
Lei Luo
2013-01-01
item search. Recently, a number of data-dependent methods have been developed, reflecting the great potential of learning for hashing. Inspired by the classic nonlinear dimensionality reduction algorithm—maximum variance unfolding, we propose a novel unsupervised hashing method, named maximum variance hashing, in this work. The idea is to maximize the total variance of the hash codes while preserving the local structure of the training data. To solve the derived optimization problem, we propose a column generation algorithm, which directly learns the binary-valued hash functions. We then extend it using anchor graphs to reduce the computational cost. Experiments on large-scale image datasets demonstrate that the proposed method outperforms state-of-the-art hashing methods in many cases.
The Maximum Resource Bin Packing Problem
Boyar, J.; Epstein, L.; Favrholdt, L.M.
2006-01-01
algorithms, First-Fit-Increasing and First-Fit-Decreasing for the maximum resource variant of classical bin packing. For the on-line variant, we define maximum resource variants of classical and dual bin packing. For dual bin packing, no on-line algorithm is competitive. For classical bin packing, we find......Usually, for bin packing problems, we try to minimize the number of bins used or in the case of the dual bin packing problem, maximize the number or total size of accepted items. This paper presents results for the opposite problems, where we would like to maximize the number of bins used...... the competitive ratio of various natural algorithms. We study the general versions of the problems as well as the parameterized versions where there is an upper bound of on the item sizes, for some integer k....
Zipf's law, power laws and maximum entropy
Visser, Matt
2013-04-01
Zipf's law, and power laws in general, have attracted and continue to attract considerable attention in a wide variety of disciplines—from astronomy to demographics to software structure to economics to linguistics to zoology, and even warfare. A recent model of random group formation (RGF) attempts a general explanation of such phenomena based on Jaynes' notion of maximum entropy applied to a particular choice of cost function. In the present paper I argue that the specific cost function used in the RGF model is in fact unnecessarily complicated, and that power laws can be obtained in a much simpler way by applying maximum entropy ideas directly to the Shannon entropy subject only to a single constraint: that the average of the logarithm of the observable quantity is specified.
Zipf's law, power laws, and maximum entropy
Visser, Matt
2012-01-01
Zipf's law, and power laws in general, have attracted and continue to attract considerable attention in a wide variety of disciplines - from astronomy to demographics to economics to linguistics to zoology, and even warfare. A recent model of random group formation [RGF] attempts a general explanation of such phenomena based on Jaynes' notion of maximum entropy applied to a particular choice of cost function. In the present article I argue that the cost function used in the RGF model is in fact unnecessarily complicated, and that power laws can be obtained in a much simpler way by applying maximum entropy ideas directly to the Shannon entropy subject only to a single constraint: that the average of the logarithm of the observable quantity is specified.
Regions of constrained maximum likelihood parameter identifiability
Lee, C.-H.; Herget, C. J.
1975-01-01
This paper considers the parameter identification problem of general discrete-time, nonlinear, multiple-input/multiple-output dynamic systems with Gaussian-white distributed measurement errors. Knowledge of the system parameterization is assumed to be known. Regions of constrained maximum likelihood (CML) parameter identifiability are established. A computation procedure employing interval arithmetic is proposed for finding explicit regions of parameter identifiability for the case of linear systems. It is shown that if the vector of true parameters is locally CML identifiable, then with probability one, the vector of true parameters is a unique maximal point of the maximum likelihood function in the region of parameter identifiability and the CML estimation sequence will converge to the true parameters.
Maximum Profit Configurations of Commercial Engines
Yiran Chen
2011-01-01
An investigation of commercial engines with finite capacity low- and high-price economic subsystems and a generalized commodity transfer law [n ∝ Δ (P m)] in commodity flow processes, in which effects of the price elasticities of supply and demand are introduced, is presented in this paper. Optimal cycle configurations of commercial engines for maximum profit are obtained by applying optimal control theory. In some special cases, the eventual state—market equilibrium—is solely determined by t...
Tissue radiation response with maximum Tsallis entropy.
Sotolongo-Grau, O; Rodríguez-Pérez, D; Antoranz, J C; Sotolongo-Costa, Oscar
2010-10-08
The expression of survival factors for radiation damaged cells is currently based on probabilistic assumptions and experimentally fitted for each tumor, radiation, and conditions. Here, we show how the simplest of these radiobiological models can be derived from the maximum entropy principle of the classical Boltzmann-Gibbs expression. We extend this derivation using the Tsallis entropy and a cutoff hypothesis, motivated by clinical observations. The obtained expression shows a remarkable agreement with the experimental data found in the literature.
Maximum Estrada Index of Bicyclic Graphs
Wang, Long; Wang, Yi
2012-01-01
Let $G$ be a simple graph of order $n$, let $\\lambda_1(G),\\lambda_2(G),...,\\lambda_n(G)$ be the eigenvalues of the adjacency matrix of $G$. The Esrada index of $G$ is defined as $EE(G)=\\sum_{i=1}^{n}e^{\\lambda_i(G)}$. In this paper we determine the unique graph with maximum Estrada index among bicyclic graphs with fixed order.
Maximum privacy without coherence, zero-error
Leung, Debbie; Yu, Nengkun
2016-09-01
We study the possible difference between the quantum and the private capacities of a quantum channel in the zero-error setting. For a family of channels introduced by Leung et al. [Phys. Rev. Lett. 113, 030512 (2014)], we demonstrate an extreme difference: the zero-error quantum capacity is zero, whereas the zero-error private capacity is maximum given the quantum output dimension.
Sengupta, Piali; Garrity, Paul
2013-04-22
Temperature is an omnipresent physical variable reflecting the rotational, vibrational and translational motion of matter, what Richard Feynman called the "jiggling" of atoms. Temperature varies across space and time, and this variation has dramatic effects on the physiology of living cells. It changes the rate and nature of chemical reactions, and it alters the configuration of the atoms that make up nucleic acids, proteins, lipids and other biomolecules, significantly affecting their activity. While life may have started in a "warm little pond", as Charles Darwin mused, the organisms that surround us today have only made it this far by devising sophisticated systems for sensing and responding to variations in temperature, and by using these systems in ways that allow them to persist and thrive in the face of thermal fluctuation.
Automatic maximum entropy spectral reconstruction in NMR.
Mobli, Mehdi; Maciejewski, Mark W; Gryk, Michael R; Hoch, Jeffrey C
2007-10-01
Developments in superconducting magnets, cryogenic probes, isotope labeling strategies, and sophisticated pulse sequences together have enabled the application, in principle, of high-resolution NMR spectroscopy to biomolecular systems approaching 1 megadalton. In practice, however, conventional approaches to NMR that utilize the fast Fourier transform, which require data collected at uniform time intervals, result in prohibitively lengthy data collection times in order to achieve the full resolution afforded by high field magnets. A variety of approaches that involve nonuniform sampling have been proposed, each utilizing a non-Fourier method of spectrum analysis. A very general non-Fourier method that is capable of utilizing data collected using any of the proposed nonuniform sampling strategies is maximum entropy reconstruction. A limiting factor in the adoption of maximum entropy reconstruction in NMR has been the need to specify non-intuitive parameters. Here we describe a fully automated system for maximum entropy reconstruction that requires no user-specified parameters. A web-accessible script generator provides the user interface to the system.
Maximum entropy analysis of cosmic ray composition
Nosek, Dalibor; Vícha, Jakub; Trávníček, Petr; Nosková, Jana
2016-01-01
We focus on the primary composition of cosmic rays with the highest energies that cause extensive air showers in the Earth's atmosphere. A way of examining the two lowest order moments of the sample distribution of the depth of shower maximum is presented. The aim is to show that useful information about the composition of the primary beam can be inferred with limited knowledge we have about processes underlying these observations. In order to describe how the moments of the depth of shower maximum depend on the type of primary particles and their energies, we utilize a superposition model. Using the principle of maximum entropy, we are able to determine what trends in the primary composition are consistent with the input data, while relying on a limited amount of information from shower physics. Some capabilities and limitations of the proposed method are discussed. In order to achieve a realistic description of the primary mass composition, we pay special attention to the choice of the parameters of the sup...
A Maximum Resonant Set of Polyomino Graphs
Zhang Heping
2016-05-01
Full Text Available A polyomino graph P is a connected finite subgraph of the infinite plane grid such that each finite face is surrounded by a regular square of side length one and each edge belongs to at least one square. A dimer covering of P corresponds to a perfect matching. Different dimer coverings can interact via an alternating cycle (or square with respect to them. A set of disjoint squares of P is a resonant set if P has a perfect matching M so that each one of those squares is M-alternating. In this paper, we show that if K is a maximum resonant set of P, then P − K has a unique perfect matching. We further prove that the maximum forcing number of a polyomino graph is equal to the cardinality of a maximum resonant set. This confirms a conjecture of Xu et al. [26]. We also show that if K is a maximal alternating set of P, then P − K has a unique perfect matching.
Maximum saliency bias in binocular fusion
Lu, Yuhao; Stafford, Tom; Fox, Charles
2016-07-01
Subjective experience at any instant consists of a single ("unitary"), coherent interpretation of sense data rather than a "Bayesian blur" of alternatives. However, computation of Bayes-optimal actions has no role for unitary perception, instead being required to integrate over every possible action-percept pair to maximise expected utility. So what is the role of unitary coherent percepts, and how are they computed? Recent work provided objective evidence for non-Bayes-optimal, unitary coherent, perception and action in humans; and further suggested that the percept selected is not the maximum a posteriori percept but is instead affected by utility. The present study uses a binocular fusion task first to reproduce the same effect in a new domain, and second, to test multiple hypotheses about exactly how utility may affect the percept. After accounting for high experimental noise, it finds that both Bayes optimality (maximise expected utility) and the previously proposed maximum-utility hypothesis are outperformed in fitting the data by a modified maximum-salience hypothesis, using unsigned utility magnitudes in place of signed utilities in the bias function.
Maximum-biomass prediction of homofermentative Lactobacillus.
Cui, Shumao; Zhao, Jianxin; Liu, Xiaoming; Chen, Yong Q; Zhang, Hao; Chen, Wei
2016-07-01
Fed-batch and pH-controlled cultures have been widely used for industrial production of probiotics. The aim of this study was to systematically investigate the relationship between the maximum biomass of different homofermentative Lactobacillus and lactate accumulation, and to develop a prediction equation for the maximum biomass concentration in such cultures. The accumulation of the end products and the depletion of nutrients by various strains were evaluated. In addition, the minimum inhibitory concentrations (MICs) of acid anions for various strains at pH 7.0 were examined. The lactate concentration at the point of complete inhibition was not significantly different from the MIC of lactate for all of the strains, although the inhibition mechanism of lactate and acetate on Lactobacillus rhamnosus was different from the other strains which were inhibited by the osmotic pressure caused by acid anions at pH 7.0. When the lactate concentration accumulated to the MIC, the strains stopped growing. The maximum biomass was closely related to the biomass yield per unit of lactate produced (YX/P) and the MIC (C) of lactate for different homofermentative Lactobacillus. Based on the experimental data obtained using different homofermentative Lactobacillus, a prediction equation was established as follows: Xmax - X0 = (0.59 ± 0.02)·YX/P·C.
The maximum intelligible range of the human voice
Boren, Braxton
This dissertation examines the acoustics of the spoken voice at high levels and the maximum number of people that could hear such a voice unamplified in the open air. In particular, it examines an early auditory experiment by Benjamin Franklin which sought to determine the maximum intelligible crowd for the Anglican preacher George Whitefield in the eighteenth century. Using Franklin's description of the experiment and a noise source on Front Street, the geometry and diffraction effects of such a noise source are examined to more precisely pinpoint Franklin's position when Whitefield's voice ceased to be intelligible. Based on historical maps, drawings, and prints, the geometry and material of Market Street is constructed as a computer model which is then used to construct an acoustic cone tracing model. Based on minimal values of the Speech Transmission Index (STI) at Franklin's position, Whitefield's on-axis Sound Pressure Level (SPL) at 1 m is determined, leading to estimates centering around 90 dBA. Recordings are carried out on trained actors and singers to determine their maximum time-averaged SPL at 1 m. This suggests that the greatest average SPL achievable by the human voice is 90-91 dBA, similar to the median estimates for Whitefield's voice. The sites of Whitefield's largest crowds are acoustically modeled based on historical evidence and maps. Based on Whitefield's SPL, the minimal STI value, and the crowd's background noise, this allows a prediction of the minimally intelligible area for each site. These yield maximum crowd estimates of 50,000 under ideal conditions, while crowds of 20,000 to 30,000 seem more reasonable when the crowd was reasonably quiet and Whitefield's voice was near 90 dBA.
Guillemot, Sylvain
2008-01-01
Given a set of leaf-labeled trees with identical leaf sets, the well-known "Maximum Agreement SubTree" problem (MAST) consists of finding a subtree homeomorphically included in all input trees and with the largest number of leaves. Its variant called "Maximum Compatible Tree" (MCT) is less stringent, as it allows the input trees to be refined. Both problems are of particular interest in computational biology, where trees encountered have often small degrees. In this paper, we study the parameterized complexity of MAST and MCT with respect to the maximum degree, denoted by D, of the input trees. It is known that MAST is polynomial for bounded D. As a counterpart, we show that the problem is W[1]-hard with respect to parameter D. Moreover, elying on recent advances in parameterized complexity we obtain a tight lower bound: while MAST can be solved in O(N^{O(D)}) time where N denotes the input length, we show that an O(N^{o(D)}) bound is not achievable, unless SNP is contained in SE. We also show that MCT is W[1...
PARTICLE SWARM OPTIMIZATION BASED OF THE MAXIMUM ...
2010-06-30
Jun 30, 2010 ... This latter change instantaneously with changing radiation and temperature, ... dealing accurately with these optimization problems and to ... Shunt resistance Rsh, in parallel with the diode, this corresponds to the leakage.
Soft X-ray polychromator for the Solar Maximum Mission
Haisch, B. M.; Levay, M.; Stern, R. A.; Strong, K. T.; Wolfson, C. J.; Acton, L. W.
1984-01-01
The XRP was designed to measure the following temporal and spatial properties of the active and flaring Sun: electron temperature, departures from steady state, ion kinetic temperatures, and electron density. The Bent Crystal Spectrometer (BCS) is capable of measuring the broadening and blue shifts often observed in the impulsive phase of flares. The six simultaneous line fluxes indicative of six different temperatures of formation observable by the Flat Crystal Spectrometer (FCS) allows the derivation of the differential emission measure of the plasma at each raster point. During the operational periods of the XRP hundreds of flares of C-level (GOES classification) were observed and brighter in both the FCS and BCS, including 5 X-flares. Associated theoretical work in atomic physics, stimulated in part by the promise of XRP measurements, has benefitted from the experimental data on solar plasmas which the XRP has provided in abundance.
Anderson, L. S.; Wickert, A. D.; Colgan, W. T.; Anderson, R. S.
2014-12-01
The Last Glacial Maximum (LGM) Yellowstone Ice Cap was the largest continuous ice body in the US Rocky Mountains. Terminal moraine ages derived from cosmogenic radionuclide dating (e.g., Licciardi and Pierce, 2008) constrain the timing of maximum Ice Cap extent. Importantly, the moraine ages vary by several thousand years around the Ice Cap; ages on the eastern outlet glaciers are significantly younger than their western counterparts. In order to interpret these observations within the context of LGM climate in North America, we perform two numerical glacier modeling experiments: 1) We model the initiation and growth of the Ice Cap to steady state; and 2) We estimate the range of LGM climate states which led to the formation of the Ice Cap. We use an efficient semi-implicit 2-D glacier model coupled to a fully implicit solution for flexural isostasy, allowing for transient links between climatic forcing, ice thickness, and earth surface deflection. Independent of parameter selection, the Ice Cap initiates in the Absaroka and Beartooth mountains and then advances across the Yellowstone plateau to the west. The Ice Cap advances to its maximum extent first to the older eastern moraines and last to the younger western and northwestern moraines. This suggests that the moraine ages may reflect the timescale required for the Ice Cap to advance across the high elevation Yellowstone plateau rather than the timing of local LGM climate. With no change in annual precipitation from the present, a mean summer temperature drop of 8-9° C is required to form the Ice Cap. Further parameter searches provide the full range of LGM paleoclimate states that led to the Yellowstone Ice Cap. Using our preferred parameter set, we find that the timescale for the growth of the complete Ice Cap is roughly 10,000 years. Isostatic subsidence helps explain the long timescale of Ice Cap growth. The Yellowstone Ice Cap caused a maximum surface deflection of 300 m (using a constant effective elastic
Maximum power operation of interacting molecular motors
Golubeva, Natalia; Imparato, Alberto
2013-01-01
We study the mechanical and thermodynamic properties of different traffic models for kinesin which are relevant in biological and experimental contexts. We find that motor-motor interactions play a fundamental role by enhancing the thermodynamic efficiency at maximum power of the motors......, as compared to the non-interacting system, in a wide range of biologically compatible scenarios. We furthermore consider the case where the motor-motor interaction directly affects the internal chemical cycle and investigate the effect on the system dynamics and thermodynamics....
Maximum a posteriori decoder for digital communications
Altes, Richard A. (Inventor)
1997-01-01
A system and method for decoding by identification of the most likely phase coded signal corresponding to received data. The present invention has particular application to communication with signals that experience spurious random phase perturbations. The generalized estimator-correlator uses a maximum a posteriori (MAP) estimator to generate phase estimates for correlation with incoming data samples and for correlation with mean phases indicative of unique hypothesized signals. The result is a MAP likelihood statistic for each hypothesized transmission, wherein the highest value statistic identifies the transmitted signal.
Kernel-based Maximum Entropy Clustering
JIANG Wei; QU Jiao; LI Benxi
2007-01-01
With the development of Support Vector Machine (SVM),the "kernel method" has been studied in a general way.In this paper,we present a novel Kernel-based Maximum Entropy Clustering algorithm (KMEC).By using mercer kernel functions,the proposed algorithm is firstly map the data from their original space to high dimensional space where the data are expected to be more separable,then perform MEC clustering in the feature space.The experimental results show that the proposed method has better performance in the non-hyperspherical and complex data structure.
Conductivity maximum in a charged colloidal suspension
Bastea, S
2009-01-27
Molecular dynamics simulations of a charged colloidal suspension in the salt-free regime show that the system exhibits an electrical conductivity maximum as a function of colloid charge. We attribute this behavior to two main competing effects: colloid effective charge saturation due to counterion 'condensation' and diffusion slowdown due to the relaxation effect. In agreement with previous observations, we also find that the effective transported charge is larger than the one determined by the Stern layer and suggest that it corresponds to the boundary fluid layer at the surface of the colloidal particles.
COMPARISON BETWEEN FORMULAS OF MAXIMUM SHIP SQUAT
PETRU SERGIU SERBAN
2016-06-01
Full Text Available Ship squat is a combined effect of ship’s draft and trim increase due to ship motion in limited navigation conditions. Over time, researchers conducted tests on models and ships to find a mathematical formula that can define squat. Various forms of calculating squat can be found in the literature. Among those most commonly used are of Barrass, Millward, Eryuzlu or ICORELS. This paper presents a comparison between the squat formulas to see the differences between them and which one provides the most satisfactory results. In this respect a cargo ship at different speeds was considered as a model for maximum squat calculations in canal navigation conditions.
Maximum entropy PDF projection: A review
Baggenstoss, Paul M.
2017-06-01
We review maximum entropy (MaxEnt) PDF projection, a method with wide potential applications in statistical inference. The method constructs a sampling distribution for a high-dimensional vector x based on knowing the sampling distribution p(z) of a lower-dimensional feature z = T (x). Under mild conditions, the distribution p(x) having highest possible entropy among all distributions consistent with p(z) may be readily found. Furthermore, the MaxEnt p(x) may be sampled, making the approach useful in Monte Carlo methods. We review the theorem and present a case study in model order selection and classification for handwritten character recognition.
Dynamical maximum entropy approach to flocking
Cavagna, Andrea; Giardina, Irene; Ginelli, Francesco; Mora, Thierry; Piovani, Duccio; Tavarone, Raffaele; Walczak, Aleksandra M.
2014-04-01
We derive a new method to infer from data the out-of-equilibrium alignment dynamics of collectively moving animal groups, by considering the maximum entropy model distribution consistent with temporal and spatial correlations of flight direction. When bird neighborhoods evolve rapidly, this dynamical inference correctly learns the parameters of the model, while a static one relying only on the spatial correlations fails. When neighbors change slowly and the detailed balance is satisfied, we recover the static procedure. We demonstrate the validity of the method on simulated data. The approach is applicable to other systems of active matter.
Zipf's law and maximum sustainable growth
Malevergne, Y; Sornette, D
2010-01-01
Zipf's law states that the number of firms with size greater than S is inversely proportional to S. Most explanations start with Gibrat's rule of proportional growth but require additional constraints. We show that Gibrat's rule, at all firm levels, yields Zipf's law under a balance condition between the effective growth rate of incumbent firms (which includes their possible demise) and the growth rate of investments in entrant firms. Remarkably, Zipf's law is the signature of the long-term optimal allocation of resources that ensures the maximum sustainable growth rate of an economy.
Gutierrez-Jurado, H. A.; Guan, H.; Wang, J.; Wang, H.; Bras, R. L.; Simmons, C. T.
2015-12-01
Quantification of evapotranspiration (ET) and its partition over regions of heterogeneous topography and canopy poses a challenge using traditional approaches. In this study, we report the results of a novel field experiment design guided by the Maximum Entropy Production model of ET (MEP-ET), formulated for estimating evaporation and transpiration from homogeneous soil and canopy. A catchment with complex terrain and patchy vegetation in South Australia was instrumented to measure temperature, humidity and net radiation at soil and canopy surfaces. Performance of the MEP-ET model to quantify transpiration and soil evaporation was evaluated during wet and dry conditions with independently and directly measured transpiration from sapflow and soil evaporation using the Bowen Ratio Energy Balance (BREB). MEP-ET transpiration shows remarkable agreement with that obtained through sapflow measurements during wet conditions, but consistently overestimates the flux during dry periods. However, an additional term introduced to the original MEP-ET model accounting for higher stomatal regulation during dry spells, based on differences between leaf and air vapor pressure deficits and temperatures, significantly improves the model performance. On the other hand, MEP-ET soil evaporation is in good agreement with that from BREB regardless of moisture conditions. The experimental design allows a plot and tree scale quantification of evaporation and transpiration respectively. This study confirms for the first time that the MEP-ET originally developed for homogeneous open bare soil and closed canopy can be used for modeling ET over heterogeneous land surfaces. Furthermore, we show that with the addition of an empirical function simulating the plants ability to regulate transpiration, and based on the same measurements of temperature and humidity, the method can produce reliable estimates of ET during both wet and dry conditions without compromising its parsimony.
45 CFR 2522.245 - How are living allowances disbursed?
2010-10-01
..., Requirements, and Benefits § 2522.245 How are living allowances disbursed? A living allowance is not a wage and programs may not pay living allowances on an hourly basis. Programs must distribute the living allowance at... 45 Public Welfare 4 2010-10-01 2010-10-01 false How are living allowances disbursed? 2522.245...
42 CFR 495.308 - Net average allowable costs as the basis for determining the incentive payment.
2010-10-01
... 42 Public Health 5 2010-10-01 2010-10-01 false Net average allowable costs as the basis for... Net average allowable costs as the basis for determining the incentive payment. (a) The first year of..., implementation or upgrade of certified electronic health records technology. (2) The maximum net...
Accurate structural correlations from maximum likelihood superpositions.
Douglas L Theobald
2008-02-01
Full Text Available The cores of globular proteins are densely packed, resulting in complicated networks of structural interactions. These interactions in turn give rise to dynamic structural correlations over a wide range of time scales. Accurate analysis of these complex correlations is crucial for understanding biomolecular mechanisms and for relating structure to function. Here we report a highly accurate technique for inferring the major modes of structural correlation in macromolecules using likelihood-based statistical analysis of sets of structures. This method is generally applicable to any ensemble of related molecules, including families of nuclear magnetic resonance (NMR models, different crystal forms of a protein, and structural alignments of homologous proteins, as well as molecular dynamics trajectories. Dominant modes of structural correlation are determined using principal components analysis (PCA of the maximum likelihood estimate of the correlation matrix. The correlations we identify are inherently independent of the statistical uncertainty and dynamic heterogeneity associated with the structural coordinates. We additionally present an easily interpretable method ("PCA plots" for displaying these positional correlations by color-coding them onto a macromolecular structure. Maximum likelihood PCA of structural superpositions, and the structural PCA plots that illustrate the results, will facilitate the accurate determination of dynamic structural correlations analyzed in diverse fields of structural biology.
Maximum Likelihood Analysis in the PEN Experiment
Lehman, Martin
2013-10-01
The experimental determination of the π+ -->e+ ν (γ) decay branching ratio currently provides the most accurate test of lepton universality. The PEN experiment at PSI, Switzerland, aims to improve the present world average experimental precision of 3 . 3 ×10-3 to 5 ×10-4 using a stopped beam approach. During runs in 2008-10, PEN has acquired over 2 ×107 πe 2 events. The experiment includes active beam detectors (degrader, mini TPC, target), central MWPC tracking with plastic scintillator hodoscopes, and a spherical pure CsI electromagnetic shower calorimeter. The final branching ratio will be calculated using a maximum likelihood analysis. This analysis assigns each event a probability for 5 processes (π+ -->e+ ν , π+ -->μ+ ν , decay-in-flight, pile-up, and hadronic events) using Monte Carlo verified probability distribution functions of our observables (energies, times, etc). A progress report on the PEN maximum likelihood analysis will be presented. Work supported by NSF grant PHY-0970013.
Leaf Dynamics of Panicum maximum under Future Climatic Changes.
Carlos Henrique Britto de Assis Prado
Full Text Available Panicum maximum Jacq. 'Mombaça' (C4 was grown in field conditions with sufficient water and nutrients to examine the effects of warming and elevated CO2 concentrations during the winter. Plants were exposed to either the ambient temperature and regular atmospheric CO2 (Control; elevated CO2 (600 ppm, eC; canopy warming (+2°C above regular canopy temperature, eT; or elevated CO2 and canopy warming (eC+eT. The temperatures and CO2 in the field were controlled by temperature free-air controlled enhancement (T-FACE and mini free-air CO2 enrichment (miniFACE facilities. The most green, expanding, and expanded leaves and the highest leaf appearance rate (LAR, leaves day(-1 and leaf elongation rate (LER, cm day(-1 were observed under eT. Leaf area and leaf biomass were higher in the eT and eC+eT treatments. The higher LER and LAR without significant differences in the number of senescent leaves could explain why tillers had higher foliage area and leaf biomass in the eT treatment. The eC treatment had the lowest LER and the fewest expanded and green leaves, similar to Control. The inhibitory effect of eC on foliage development in winter was indicated by the fewer green, expanded, and expanding leaves under eC+eT than eT. The stimulatory and inhibitory effects of the eT and eC treatments, respectively, on foliage raised and lowered, respectively, the foliar nitrogen concentration. The inhibition of foliage by eC was confirmed by the eC treatment having the lowest leaf/stem biomass ratio and by the change in leaf biomass-area relationships from linear or exponential growth to rectangular hyperbolic growth under eC. Besides, eC+eT had a synergist effect, speeding up leaf maturation. Therefore, with sufficient water and nutrients in winter, the inhibitory effect of elevated CO2 on foliage could be partially offset by elevated temperatures and relatively high P. maximum foliage production could be achieved under future climatic change.
Leaf Dynamics of Panicum maximum under Future Climatic Changes.
Britto de Assis Prado, Carlos Henrique; Haik Guedes de Camargo-Bortolin, Lívia; Castro, Érique; Martinez, Carlos Alberto
2016-01-01
Panicum maximum Jacq. 'Mombaça' (C4) was grown in field conditions with sufficient water and nutrients to examine the effects of warming and elevated CO2 concentrations during the winter. Plants were exposed to either the ambient temperature and regular atmospheric CO2 (Control); elevated CO2 (600 ppm, eC); canopy warming (+2°C above regular canopy temperature, eT); or elevated CO2 and canopy warming (eC+eT). The temperatures and CO2 in the field were controlled by temperature free-air controlled enhancement (T-FACE) and mini free-air CO2 enrichment (miniFACE) facilities. The most green, expanding, and expanded leaves and the highest leaf appearance rate (LAR, leaves day(-1)) and leaf elongation rate (LER, cm day(-1)) were observed under eT. Leaf area and leaf biomass were higher in the eT and eC+eT treatments. The higher LER and LAR without significant differences in the number of senescent leaves could explain why tillers had higher foliage area and leaf biomass in the eT treatment. The eC treatment had the lowest LER and the fewest expanded and green leaves, similar to Control. The inhibitory effect of eC on foliage development in winter was indicated by the fewer green, expanded, and expanding leaves under eC+eT than eT. The stimulatory and inhibitory effects of the eT and eC treatments, respectively, on foliage raised and lowered, respectively, the foliar nitrogen concentration. The inhibition of foliage by eC was confirmed by the eC treatment having the lowest leaf/stem biomass ratio and by the change in leaf biomass-area relationships from linear or exponential growth to rectangular hyperbolic growth under eC. Besides, eC+eT had a synergist effect, speeding up leaf maturation. Therefore, with sufficient water and nutrients in winter, the inhibitory effect of elevated CO2 on foliage could be partially offset by elevated temperatures and relatively high P. maximum foliage production could be achieved under future climatic change.
An efficient approximation algorithm for finding a maximum clique using Hopfield network learning.
Wang, Rong Long; Tang, Zheng; Cao, Qi Ping
2003-07-01
In this article, we present a solution to the maximum clique problem using a gradient-ascent learning algorithm of the Hopfield neural network. This method provides a near-optimum parallel algorithm for finding a maximum clique. To do this, we use the Hopfield neural network to generate a near-maximum clique and then modify weights in a gradient-ascent direction to allow the network to escape from the state of near-maximum clique to maximum clique or better. The proposed parallel algorithm is tested on two types of random graphs and some benchmark graphs from the Center for Discrete Mathematics and Theoretical Computer Science (DIMACS). The simulation results show that the proposed learning algorithm can find good solutions in reasonable computation time.
Lake Basin Fetch and Maximum Length/Width
Minnesota Department of Natural Resources — Linear features representing the Fetch, Maximum Length and Maximum Width of a lake basin. Fetch, maximum length and average width are calcuated from the lake polygon...
Continental warming preceding the Palaeocene-Eocene thermal maximum.
Secord, Ross; Gingerich, Philip D; Lohmann, Kyger C; Macleod, Kenneth G
2010-10-21
Marine and continental records show an abrupt negative shift in carbon isotope values at ∼55.8 Myr ago. This carbon isotope excursion (CIE) is consistent with the release of a massive amount of isotopically light carbon into the atmosphere and was associated with a dramatic rise in global temperatures termed the Palaeocene-Eocene thermal maximum (PETM). Greenhouse gases released during the CIE, probably including methane, have often been considered the main cause of PETM warming. However, some evidence from the marine record suggests that warming directly preceded the CIE, raising the possibility that the CIE and PETM may have been linked to earlier warming with different origins. Yet pre-CIE warming is still uncertain. Disentangling the sequence of events before and during the CIE and PETM is important for understanding the causes of, and Earth system responses to, abrupt climate change. Here we show that continental warming of about 5 °C preceded the CIE in the Bighorn Basin, Wyoming. Our evidence, based on oxygen isotopes in mammal teeth (which reflect temperature-sensitive fractionation processes) and other proxies, reveals a marked temperature increase directly below the CIE, and again in the CIE. Pre-CIE warming is also supported by a negative amplification of δ(13)C values in soil carbonates below the CIE. Our results suggest that at least two sources of warming-the earlier of which is unlikely to have been methane-contributed to the PETM.
Maximum principle and convergence of central schemes based on slope limiters
Mehmetoglu, Orhan
2012-01-01
A maximum principle and convergence of second order central schemes is proven for scalar conservation laws in dimension one. It is well known that to establish a maximum principle a nonlinear piecewise linear reconstruction is needed and a typical choice is the minmod limiter. Unfortunately, this implies that the scheme uses a first order reconstruction at local extrema. The novelty here is that we allow local nonlinear reconstructions which do not reduce to first order at local extrema and still prove maximum principle and convergence. © 2011 American Mathematical Society.
On the Law of Equal Pressure Maximum%等压最大值定律
王子佳
2011-01-01
This paper states the law of equal pressure maximum, including： the law of gas temperature T＇s equal pressure maximum; the law of gas volume X＇s equal pressure maximum; the law of gas cubage V＇s equal pressure maximum; the law of unit gas volume X＇s equal pressure maximum.%阐述了等压最大值定律，包括：（1）瓦斯温度T等压最大值定律，（2）瓦斯量N等压最大值定律，（3）瓦斯容积V等压最大值定律，（4）单位容积瓦斯量x等压最大值定律4种．
Nutrient maximums related to low oxygen concentrations in the southern Canada Basin
JIN Ming-ming; SHI Jiuxin; LU Yong; CHEN Jianfang; GAO Guoping; WU Jingfeng; ZHANG Haisheng
2005-01-01
The phenomenon of nutrient maximums at 70～200 m occurred only in the region of the Canada Basin among the world oceans. The prevailing hypothesis was that the direct injection of the low-temperature high-nutrient brines from the Chukchi Sea shelf (＜50 m) in winter provided the nutrient maximums. However, we found that there are five problems in the direct injection process. Formerly Jin et al. considered that the formation of nutrient maximums can be a process of locally long-term regeneration. Here we propose a regeneration-mixture process. Data of temperature, salinity, oxygen and nutrients were collected at three stations in the southern Canada Basin during the summer 1999 cruise. We identified the cores of the surface, near-surface, potential temperature maximum waters and Arctic Bottom Water by the diagrams and vertical profiles of salinity, potential temperature, oxygen and nutrients. The historical 129Ⅰ data indicated that the surface and near-surface waters were Pacific-origin, but the waters below the potential temperature maximum core depth was Atlantic-origin. Along with the correlation of nutrient maximums and very low oxygen contents in the near-surface water, we hypothesize that, the putative organic matter was decomposed to inorganic nutrients; and the Pacific water was mixed with the Atlantic water in the transition zone. The idea of the regeneration-mixture process agrees with the historical observations of no apparent seasonal changes, the smooth nutrient profiles, the lowest saturation of CaCO3 above 400 m, low rate of CFC-11 ventilation and 3H-3He ages of 8～18 a around the nutrient maximum depths.
Maximum tunneling velocities in symmetric double well potentials
Manz, Jörn; Schmidt, Burkhard; Yang, Yonggang
2014-01-01
We consider coherent tunneling of one-dimensional model systems in non-cyclic or cyclic symmetric double well potentials. Generic potentials are constructed which allow for analytical estimates of the quantum dynamics in the non-relativistic deep tunneling regime, in terms of the tunneling distance, barrier height and mass (or moment of inertia). For cyclic systems, the results may be scaled to agree well with periodic potentials for which semi-analytical results in terms of Mathieu functions exist. Starting from a wavepacket which is initially localized in one of the potential wells, the subsequent periodic tunneling is associated with tunneling velocities. These velocities (or angular velocities) are evaluated as the ratio of the flux densities versus the probability densities. The maximum velocities are found under the top of the barrier where they scale as the square root of the ratio of barrier height and mass (or moment of inertia), independent of the tunneling distance. They are applied exemplarily to ...
Vector control structure of an asynchronous motor at maximum torque
Chioncel, C. P.; Tirian, G. O.; Gillich, N.; Raduca, E.
2016-02-01
Vector control methods offer the possibility to gain high performance, being widely used. Certain applications require an optimum control in limit operating conditions, as, at maximum torque, that is not always satisfied. The paper presents how the voltage and the frequency for an asynchronous machine (ASM) operating at variable speed are determinate, with an accent on the method that keeps the rotor flux constant. The simulation analyses consider three load types: variable torque and speed, variable torque and constant speed, constant torque and variable speed. The final values of frequency and voltage are obtained through the proposed control schemes with one controller using the simulation language based on the Maple module. The dynamic analysis of the system is done for the case with P and PI controller and allows conclusions on the proposed method, which can have different applications, as the ASM in wind turbines.
Network Decomposition and Maximum Independent Set Part Ⅰ: Theoretic Basis
朱松年; 朱嫱
2003-01-01
The structure and characteristics of a connected network are analyzed, and a special kind of sub-network, which can optimize the iteration processes, is discovered. Then, the sufficient and necessary conditions for obtaining the maximum independent set are deduced. It is found that the neighborhood of this sub-network possesses the similar characters, but both can never be allowed incorporated together. Particularly, it is identified that the network can be divided into two parts by a certain style, and then both of them can be transformed into a pair sets network, where the special sub-networks and their neighborhoods appear alternately distributed throughout the entire pair sets network. By use of this characteristic, the network decomposed enough without losing any solutions is obtained. All of these above will be able to make well ready for developing a much better algorithm with polynomial time bound for an odd network in the the application research part of this subject.
Maximum entropy principle and texture formation
Arminjon, M; Arminjon, Mayeul; Imbault, Didier
2006-01-01
The macro-to-micro transition in a heterogeneous material is envisaged as the selection of a probability distribution by the Principle of Maximum Entropy (MAXENT). The material is made of constituents, e.g. given crystal orientations. Each constituent is itself made of a large number of elementary constituents. The relevant probability is the volume fraction of the elementary constituents that belong to a given constituent and undergo a given stimulus. Assuming only obvious constraints in MAXENT means describing a maximally disordered material. This is proved to have the same average stimulus in each constituent. By adding a constraint in MAXENT, a new model, potentially interesting e.g. for texture prediction, is obtained.
MLDS: Maximum Likelihood Difference Scaling in R
Kenneth Knoblauch
2008-01-01
Full Text Available The MLDS package in the R programming language can be used to estimate perceptual scales based on the results of psychophysical experiments using the method of difference scaling. In a difference scaling experiment, observers compare two supra-threshold differences (a,b and (c,d on each trial. The approach is based on a stochastic model of how the observer decides which perceptual difference (or interval (a,b or (c,d is greater, and the parameters of the model are estimated using a maximum likelihood criterion. We also propose a method to test the model by evaluating the self-consistency of the estimated scale. The package includes an example in which an observer judges the differences in correlation between scatterplots. The example may be readily adapted to estimate perceptual scales for arbitrary physical continua.
Maximum Profit Configurations of Commercial Engines
Yiran Chen
2011-06-01
Full Text Available An investigation of commercial engines with finite capacity low- and high-price economic subsystems and a generalized commodity transfer law [n ∝ Δ (P m] in commodity flow processes, in which effects of the price elasticities of supply and demand are introduced, is presented in this paper. Optimal cycle configurations of commercial engines for maximum profit are obtained by applying optimal control theory. In some special cases, the eventual state—market equilibrium—is solely determined by the initial conditions and the inherent characteristics of two subsystems; while the different ways of transfer affect the model in respects of the specific forms of the paths of prices and the instantaneous commodity flow, i.e., the optimal configuration.
Maximum Segment Sum, Monadically (distilled tutorial
Jeremy Gibbons
2011-09-01
Full Text Available The maximum segment sum problem is to compute, given a list of integers, the largest of the sums of the contiguous segments of that list. This problem specification maps directly onto a cubic-time algorithm; however, there is a very elegant linear-time solution too. The problem is a classic exercise in the mathematics of program construction, illustrating important principles such as calculational development, pointfree reasoning, algebraic structure, and datatype-genericity. Here, we take a sideways look at the datatype-generic version of the problem in terms of monadic functional programming, instead of the traditional relational approach; the presentation is tutorial in style, and leavened with exercises for the reader.
Maximum Information and Quantum Prediction Algorithms
McElwaine, J N
1997-01-01
This paper describes an algorithm for selecting a consistent set within the consistent histories approach to quantum mechanics and investigates its properties. The algorithm uses a maximum information principle to select from among the consistent sets formed by projections defined by the Schmidt decomposition. The algorithm unconditionally predicts the possible events in closed quantum systems and ascribes probabilities to these events. A simple spin model is described and a complete classification of all exactly consistent sets of histories formed from Schmidt projections in the model is proved. This result is used to show that for this example the algorithm selects a physically realistic set. Other tentative suggestions in the literature for set selection algorithms using ideas from information theory are discussed.
Maximum process problems in optimal control theory
Goran Peskir
2005-01-01
Full Text Available Given a standard Brownian motion (Btt≥0 and the equation of motion dXt=vtdt+2dBt, we set St=max0≤s≤tXs and consider the optimal control problem supvE(Sτ−Cτ, where c>0 and the supremum is taken over all admissible controls v satisfying vt∈[μ0,μ1] for all t up to τ=inf{t>0|Xt∉(ℓ0,ℓ1} with μ0g∗(St, where s↦g∗(s is a switching curve that is determined explicitly (as the unique solution to a nonlinear differential equation. The solution found demonstrates that the problem formulations based on a maximum functional can be successfully included in optimal control theory (calculus of variations in addition to the classic problem formulations due to Lagrange, Mayer, and Bolza.
Maximum entropy model for business cycle synchronization
Xi, Ning; Muneepeerakul, Rachata; Azaele, Sandro; Wang, Yougui
2014-11-01
The global economy is a complex dynamical system, whose cyclical fluctuations can mainly be characterized by simultaneous recessions or expansions of major economies. Thus, the researches on the synchronization phenomenon are key to understanding and controlling the dynamics of the global economy. Based on a pairwise maximum entropy model, we analyze the business cycle synchronization of the G7 economic system. We obtain a pairwise-interaction network, which exhibits certain clustering structure and accounts for 45% of the entire structure of the interactions within the G7 system. We also find that the pairwise interactions become increasingly inadequate in capturing the synchronization as the size of economic system grows. Thus, higher-order interactions must be taken into account when investigating behaviors of large economic systems.
Quantum gravity momentum representation and maximum energy
Moffat, J. W.
2016-11-01
We use the idea of the symmetry between the spacetime coordinates xμ and the energy-momentum pμ in quantum theory to construct a momentum space quantum gravity geometry with a metric sμν and a curvature tensor Pλ μνρ. For a closed maximally symmetric momentum space with a constant 3-curvature, the volume of the p-space admits a cutoff with an invariant maximum momentum a. A Wheeler-DeWitt-type wave equation is obtained in the momentum space representation. The vacuum energy density and the self-energy of a charged particle are shown to be finite, and modifications of the electromagnetic radiation density and the entropy density of a system of particles occur for high frequencies.
Video segmentation using Maximum Entropy Model
QIN Li-juan; ZHUANG Yue-ting; PAN Yun-he; WU Fei
2005-01-01
Detecting objects of interest from a video sequence is a fundamental and critical task in automated visual surveillance.Most current approaches only focus on discriminating moving objects by background subtraction whether or not the objects of interest can be moving or stationary. In this paper, we propose layers segmentation to detect both moving and stationary target objects from surveillance video. We extend the Maximum Entropy (ME) statistical model to segment layers with features, which are collected by constructing a codebook with a set of codewords for each pixel. We also indicate how the training models are used for the discrimination of target objects in surveillance video. Our experimental results are presented in terms of the success rate and the segmenting precision.
A maximum entropy model for opinions in social groups
Davis, Sergio; Navarrete, Yasmín; Gutiérrez, Gonzalo
2014-04-01
We study how the opinions of a group of individuals determine their spatial distribution and connectivity, through an agent-based model. The interaction between agents is described by a Hamiltonian in which agents are allowed to move freely without an underlying lattice (the average network topology connecting them is determined from the parameters). This kind of model was derived using maximum entropy statistical inference under fixed expectation values of certain probabilities that (we propose) are relevant to social organization. Control parameters emerge as Lagrange multipliers of the maximum entropy problem, and they can be associated with the level of consequence between the personal beliefs and external opinions, and the tendency to socialize with peers of similar or opposing views. These parameters define a phase diagram for the social system, which we studied using Monte Carlo Metropolis simulations. Our model presents both first and second-order phase transitions, depending on the ratio between the internal consequence and the interaction with others. We have found a critical value for the level of internal consequence, below which the personal beliefs of the agents seem to be irrelevant.
Distribution of phytoplankton groups within the deep chlorophyll maximum
Latasa, Mikel
2016-11-01
The fine vertical distribution of phytoplankton groups within the deep chlorophyll maximum (DCM) was studied in the NE Atlantic during summer stratification. A simple but unconventional sampling strategy allowed examining the vertical structure with ca. 2 m resolution. The distribution of Prochlorococcus, Synechococcus, chlorophytes, pelagophytes, small prymnesiophytes, coccolithophores, diatoms, and dinoflagellates was investigated with a combination of pigment-markers, flow cytometry and optical and FISH microscopy. All groups presented minimum abundances at the surface and a maximum in the DCM layer. The cell distribution was not vertically symmetrical around the DCM peak and cells tended to accumulate in the upper part of the DCM layer. The more symmetrical distribution of chlorophyll than cells around the DCM peak was due to the increase of pigment per cell with depth. We found a vertical alignment of phytoplankton groups within the DCM layer indicating preferences for different ecological niches in a layer with strong gradients of light and nutrients. Prochlorococcus occupied the shallowest and diatoms the deepest layers. Dinoflagellates, Synechococcus and small prymnesiophytes preferred shallow DCM layers, and coccolithophores, chlorophytes and pelagophytes showed a preference for deep layers. Cell size within groups changed with depth in a pattern related to their mean size: the cell volume of the smallest group increased the most with depth while the cell volume of the largest group decreased the most. The vertical alignment of phytoplankton groups confirms that the DCM is not a homogeneous entity and indicates groups’ preferences for different ecological niches within this layer.
METHOD FOR DETERMINING THE MAXIMUM ARRANGEMENT FACTOR OF FOOTWEAR PARTS
DRIŞCU Mariana
2014-05-01
Full Text Available By classic methodology, designing footwear is a very complex and laborious activity. That is because classic methodology requires many graphic executions using manual means, which consume a lot of the producer’s time. Moreover, the results of this classical methodology may contain many inaccuracies with the most unpleasant consequences for the footwear producer. Thus, the costumer that buys a footwear product by taking into consideration the characteristics written on the product (size, width can notice after a period that the product has flaws because of the inadequate design. In order to avoid this kind of situations, the strictest scientific criteria must be followed when one designs a footwear product. The decisive step in this way has been made some time ago, when, as a result of powerful technical development and massive implementation of electronical calculus systems and informatics, This paper presents a product software for determining all possible arrangements of a footwear product’s reference points, in order to automatically acquire the maximum arrangement factor. The user multiplies the pattern in order to find the economic arrangement for the reference points. In this purpose, the user must probe few arrangement variants, in the translation and rotate-translation system. The same process is used in establishing the arrangement factor for the two points of reference of the designed footwear product. After probing several variants of arrangement in the translation and rotation and translation systems, the maximum arrangement factors are chosen. This allows the user to estimate the material wastes.
MaxOcc: a web portal for maximum occurrence analysis
Bertini, Ivano, E-mail: ivanobertini@cerm.unifi.it; Ferella, Lucio; Luchinat, Claudio, E-mail: luchinat@cerm.unifi.it; Parigi, Giacomo [Magnetic Resonance Center (CERM), University of Florence (Italy); Petoukhov, Maxim V. [EMBL, Hamburg Outstation (Germany); Ravera, Enrico; Rosato, Antonio [Magnetic Resonance Center (CERM), University of Florence (Italy); Svergun, Dmitri I. [EMBL, Hamburg Outstation (Germany)
2012-08-15
The MaxOcc web portal is presented for the characterization of the conformational heterogeneity of two-domain proteins, through the calculation of the Maximum Occurrence that each protein conformation can have in agreement with experimental data. Whatever the real ensemble of conformations sampled by a protein, the weight of any conformation cannot exceed the calculated corresponding Maximum Occurrence value. The present portal allows users to compute these values using any combination of restraints like pseudocontact shifts, paramagnetism-based residual dipolar couplings, paramagnetic relaxation enhancements and small angle X-ray scattering profiles, given the 3D structure of the two domains as input. MaxOcc is embedded within the NMR grid services of the WeNMR project and is available via the WeNMR gateway at http://py-enmr.cerm.unifi.it/access/index/maxocchttp://py-enmr.cerm.unifi.it/access/index/maxocc. It can be used freely upon registration to the grid with a digital certificate.
Maximum hydrogen production from genetically modified microalgae biomass
Vargas, Jose; Kava, Vanessa; Ordonez, Juan
A transient mathematical model for managing microalgae derived H2 production as a source of renewable energy is developed for a well stirred photobioreactor, PBR. The model allows for the determination of microalgae and H2 mass fractions produced by the PBR in time. A Michaelis-Menten expression is proposed for modeling the rate of H2 production, which introduces an expression to calculate the resulting effect on H2 production rate after genetically modifying the microalgae. The indirect biophotolysis process was used. Therefore, an opportunity was found to optimize the aerobic to anaerobic stages time ratio of the cycle for maximum H2 production rate, i.e., the process rhythm. A system thermodynamic optimization is conducted with the model equations to find accurately the optimal system operating rhythm for maximum H2 production rate, and how wild and genetically modified species compare to each other. The maxima found are sharp, showing up to a ~60% variation in hydrogen production rate within 2 days around the optimal rhythm, which highlights the importance of system operation in such condition. Therefore, the model is expected to be useful for design, control and optimization of H2 production. Brazilian National Council of Scientific and Technological Development, CNPq (project 482336/2012-9).
Superfast maximum-likelihood reconstruction for quantum tomography
Shang, Jiangwei; Zhang, Zhengyun; Ng, Hui Khoon
2017-06-01
Conventional methods for computing maximum-likelihood estimators (MLE) often converge slowly in practical situations, leading to a search for simplifying methods that rely on additional assumptions for their validity. In this work, we provide a fast and reliable algorithm for maximum-likelihood reconstruction that avoids this slow convergence. Our method utilizes the state-of-the-art convex optimization scheme, an accelerated projected-gradient method, that allows one to accommodate the quantum nature of the problem in a different way than in the standard methods. We demonstrate the power of our approach by comparing its performance with other algorithms for n -qubit state tomography. In particular, an eight-qubit situation that purportedly took weeks of computation time in 2005 can now be completed in under a minute for a single set of data, with far higher accuracy than previously possible. This refutes the common claim that MLE reconstruction is slow and reduces the need for alternative methods that often come with difficult-to-verify assumptions. In fact, recent methods assuming Gaussian statistics or relying on compressed sensing ideas are demonstrably inapplicable for the situation under consideration here. Our algorithm can be applied to general optimization problems over the quantum state space; the philosophy of projected gradients can further be utilized for optimization contexts with general constraints.
IDENTIFICATION OF IDEOTYPES BY CANONICAL ANALYSIS IN Panicum maximum
Janaina Azevedo Martuscello
2015-04-01
Full Text Available Grouping of genotypes by canonical variable analysis is an important tool in breeding. It allows the grouping of individuals with similar characteristics that are associated with superior agronomic performance and may indicate the ideal profile of a plant for the region. The objective of the present study was to define, by canonical analysis, the agronomic profile of Panicum maximum plants adapted to the Agreste region. The experiment was conducted in a completely randomized design with 28 treatments, 22 genotypes of Panicum maximum, and cultivars Mombasa, Tanzania, Massai, Milenio, BRS Zuri, and BRS Tamani in triplicate in 4-m² plots. Plots were harvested five times and the following traits were evaluated: plant height; total, leaf, and stem; dead dry matter yields; leaf:stem ratio; leaf percentage; and volumetric density of forage. The analysis of canonical variables was performed based on the phenotypic means of the evaluated traits and on the residual variance and covariance matrix. Genotype PM34 showed higher mean leaf dry matter yield under the conditions of the Agreste of Alagoas (on average 53% higher than cultivars Mombasa, Tanzania, Milenio and Massai. It was possible to summarize the variation observed in eight agronomic characteristics in only two canonical variables accounting for 81.44 % of the data variation. The ideotype plant adapted to the conditions of the Agreste should be tall and present high leaf yield, leaf percentage, and leaf:stem ratio, and intermediate values of volumetric density of forage.
Evaluation of pliers' grip spans in the maximum gripping task and sub-maximum cutting task.
Kim, Dae-Min; Kong, Yong-Ku
2016-12-01
A total of 25 males participated to investigate the effects of the grip spans of pliers on the total grip force, individual finger forces and muscle activities in the maximum gripping task and wire-cutting tasks. In the maximum gripping task, results showed that the 50-mm grip span had significantly higher total grip strength than the other grip spans. In the cutting task, the 50-mm grip span also showed significantly higher grip strength than the 65-mm and 80-mm grip spans, whereas the muscle activities showed a higher value at 80-mm grip span. The ratios of cutting force to maximum grip strength were also investigated. Ratios of 30.3%, 31.3% and 41.3% were obtained by grip spans of 50-mm, 65-mm, and 80-mm, respectively. Thus, the 50-mm grip span for pliers might be recommended to provide maximum exertion in gripping tasks, as well as lower maximum-cutting force ratios in the cutting tasks.
Cosmic shear measurement with maximum likelihood and maximum a posteriori inference
Hall, Alex
2016-01-01
We investigate the problem of noise bias in maximum likelihood and maximum a posteriori estimators for cosmic shear. We derive the leading and next-to-leading order biases and compute them in the context of galaxy ellipticity measurements, extending previous work on maximum likelihood inference for weak lensing. We show that a large part of the bias on these point estimators can be removed using information already contained in the likelihood when a galaxy model is specified, without the need for external calibration. We test these bias-corrected estimators on simulated galaxy images similar to those expected from planned space-based weak lensing surveys, with very promising results. We find that the introduction of an intrinsic shape prior mitigates noise bias, such that the maximum a posteriori estimate can be made less biased than the maximum likelihood estimate. Second-order terms offer a check on the convergence of the estimators, but are largely sub-dominant. We show how biases propagate to shear estima...
Efficiency at Maximum Power of Low-Dissipation Carnot Engines
Esposito, Massimiliano; Kawai, Ryoichi; Lindenberg, Katja; van den Broeck, Christian
2010-10-01
We study the efficiency at maximum power, η*, of engines performing finite-time Carnot cycles between a hot and a cold reservoir at temperatures Th and Tc, respectively. For engines reaching Carnot efficiency ηC=1-Tc/Th in the reversible limit (long cycle time, zero dissipation), we find in the limit of low dissipation that η* is bounded from above by ηC/(2-ηC) and from below by ηC/2. These bounds are reached when the ratio of the dissipation during the cold and hot isothermal phases tend, respectively, to zero or infinity. For symmetric dissipation (ratio one) the Curzon-Ahlborn efficiency ηCA=1-Tc/Th is recovered.
Conjugate variables in continuous maximum-entropy inference.
Davis, Sergio; Gutiérrez, Gonzalo
2012-11-01
For a continuous maximum-entropy distribution (obtained from an arbitrary number of simultaneous constraints), we derive a general relation connecting the Lagrange multipliers and the expectation values of certain particularly constructed functions of the states of the system. From this relation, an estimator for a given Lagrange multiplier can be constructed from derivatives of the corresponding constraining function. These estimators sometimes lead to the determination of the Lagrange multipliers by way of solving a linear system, and, in general, they provide another tool to widen the applicability of Jaynes's formalism. This general relation, especially well suited for computer simulation techniques, also provides some insight into the interpretation of the hypervirial relations known in statistical mechanics and the recently derived microcanonical dynamical temperature. We illustrate the usefulness of these new relations with several applications in statistics.
Efficiency at maximum power of low-dissipation Carnot engines.
Esposito, Massimiliano; Kawai, Ryoichi; Lindenberg, Katja; Van den Broeck, Christian
2010-10-01
We study the efficiency at maximum power, η*, of engines performing finite-time Carnot cycles between a hot and a cold reservoir at temperatures Th and Tc, respectively. For engines reaching Carnot efficiency ηC=1-Tc/Th in the reversible limit (long cycle time, zero dissipation), we find in the limit of low dissipation that η* is bounded from above by ηC/(2-ηC) and from below by ηC/2. These bounds are reached when the ratio of the dissipation during the cold and hot isothermal phases tend, respectively, to zero or infinity. For symmetric dissipation (ratio one) the Curzon-Ahlborn efficiency ηCA=1-√Tc/Th] is recovered.
Maximum Power Point Tracking of Photovoltaic System Using Intelligent Controller
Swathy C.S
2013-04-01
Full Text Available Photovoltaic systems normally use a maximum power point tracking (MPPT technique to continuously give forth the highest probable power to the load when the temperature and solar irradiationchanges occur. This subdues the problem of mismatch between the given load and the solar array. The energy conservation principle is used to obtain small signal model and transfer function. A simulationwork handling with MPPT controller, a DC/DC boost converter feeding a load is achieved. PI controller and fuzzy logic controllers were used as the MPPT controller, which controls the dc/dc converter. Simulations and experimental results showed excellent performance and were used for comparing PI controller and fuzzy logic controller.
Maximum caliber inference and the stochastic Ising model
Cafaro, Carlo; Ali, Sean Alan
2016-11-01
We investigate the maximum caliber variational principle as an inference algorithm used to predict dynamical properties of complex nonequilibrium, stationary, statistical systems in the presence of incomplete information. Specifically, we maximize the path entropy over discrete time step trajectories subject to normalization, stationarity, and detailed balance constraints together with a path-dependent dynamical information constraint reflecting a given average global behavior of the complex system. A general expression for the transition probability values associated with the stationary random Markov processes describing the nonequilibrium stationary system is computed. By virtue of our analysis, we uncover that a convenient choice of the dynamical information constraint together with a perturbative asymptotic expansion with respect to its corresponding Lagrange multiplier of the general expression for the transition probability leads to a formal overlap with the well-known Glauber hyperbolic tangent rule for the transition probability for the stochastic Ising model in the limit of very high temperatures of the heat reservoir.
Forecasting ozone daily maximum levels at Santiago, Chile
Jorquera, Héctor; Pérez, Ricardo; Cipriano, Aldo; Espejo, Andrés; Victoria Letelier, M.; Acuña, Gonzalo
In major urban areas, air pollution impact on health is serious enough to include it in the group of meteorological variables that are forecast daily. This work focusses on the comparison of different forecasting systems for daily maximum ozone levels at Santiago, Chile. The modelling tools used for these systems were linear time series, artificial neural networks and fuzzy models. The structure of the forecasting model was derived from basic principles and it includes a combination of persistence and daily maximum air temperature as input variables. Assessment of the models is based on two indices: their ability to forecast well an episode, and their tendency to forecast an episode that did not occur at the end (a false positive). All the models tried in this work showed good forecasting performance, with 70-95% of successful forecasts at two monitor sites: Downtown (moderate impacts) and Eastern (downwind, highest impacts). The number of false positives was not negligible, but this may be improved by expressing the forecast in broad classes: low, average, high, very high impacts; the fuzzy model was the most reliable forecast, with the lowest number of false positives among the different models evaluated. The quality of the results and the dynamics of ozone formation suggest the use of a forecast to warn people about excessive exposure during episodic days at Santiago.
Dependence of maximum concentration from chemical accidents on release duration
Hanna, Steven; Chang, Joseph
2017-01-01
Chemical accidents often involve releases of a total mass, Q, of stored material in a tank over a time duration, td, of less than a few minutes. The value of td is usually uncertain because of lack of knowledge of key information, such as the size and location of the hole and the pressure and temperature of the chemical. In addition, it is rare that eyewitnesses or video cameras are present at the time of the accident. For inhalation hazards, serious health effects (such as damage to the respiratory system) are determined by short term averages (pressurized liquefied chlorine releases from tanks are given, focusing on scenarios from the Jack Rabbit I (JR I) field experiment. The analytical calculations and the predictions of the SLAB dense gas dispersion model agree that the ratio of maximum C for two different td's is greatest (as much as a factor of ten) near the source. At large distances (beyond a few km for the JR I scenarios), where tt exceeds both td's, the ratio of maximum C approaches unity.
Maximum bubble pressure rheology of low molecular mass organogels.
Fei, Pengzhan; Wood, Steven J; Chen, Yan; Cavicchi, Kevin A
2015-01-13
Maximum bubble pressure rheology is used to characterize organogels of 0.25 wt % 12-hydroxystearic acid (12-HSA) in mineral oil, 3 wt % (1,3:2,4) dibenzylidene sorbitol (DBS) in poly(ethylene glycol), and 1 wt % 1,3:2,4-bis(3,4-dimethylbenzylidene) sorbitol (DMDBS) in poly(ethylene glycol). The maximum pressure required to inflate a bubble at the end of capillary inserted in a gel is measured. This pressure is related to the gel modulus in the case of elastic cavitation and the gel modulus and toughness in the case of irreversible fracture. The 12-HSA/mineral oil gels are used to demonstrate that this is a facile technique useful for studying time-dependent gel formation and aging and the thermal transition from a gel to a solution. Comparison is made to both qualitative gel tilting measurements and quantitative oscillatory shear rheology to highlight the utility of this measurement and its complementary nature to oscillatory shear rheology. The DBS and DMDBS demonstrate the generality of this measurement to measure gel transition temperatures.
Measurement and relevance of maximum metabolic rate in fishes.
Norin, T; Clark, T D
2016-01-01
Maximum (aerobic) metabolic rate (MMR) is defined here as the maximum rate of oxygen consumption (M˙O2max ) that a fish can achieve at a given temperature under any ecologically relevant circumstance. Different techniques exist for eliciting MMR of fishes, of which swim-flume respirometry (critical swimming speed tests and burst-swimming protocols) and exhaustive chases are the most common. Available data suggest that the most suitable method for eliciting MMR varies with species and ecotype, and depends on the propensity of the fish to sustain swimming for extended durations as well as its capacity to simultaneously exercise and digest food. MMR varies substantially (>10 fold) between species with different lifestyles (i.e. interspecific variation), and to a lesser extent (aerobic scope, interest in measuring this trait has spread across disciplines in attempts to predict effects of climate change on fish populations. Here, various techniques used to elicit and measure MMR in different fish species with contrasting lifestyles are outlined and the relevance of MMR to the ecology, fitness and climate change resilience of fishes is discussed.
Maximum power analysis of photovoltaic module in Ramadi city
Shahatha Salim, Majid; Mohammed Najim, Jassim [College of Science, University of Anbar (Iraq); Mohammed Salih, Salih [Renewable Energy Research Center, University of Anbar (Iraq)
2013-07-01
Performance of photovoltaic (PV) module is greatly dependent on the solar irradiance, operating temperature, and shading. Solar irradiance can have a significant impact on power output of PV module and energy yield. In this paper, a maximum PV power which can be obtain in Ramadi city (100km west of Baghdad) is practically analyzed. The analysis is based on real irradiance values obtained as the first time by using Soly2 sun tracker device. Proper and adequate information on solar radiation and its components at a given location is very essential in the design of solar energy systems. The solar irradiance data in Ramadi city were analyzed based on the first three months of 2013. The solar irradiance data are measured on earth's surface in the campus area of Anbar University. Actual average data readings were taken from the data logger of sun tracker system, which sets to save the average readings for each two minutes and based on reading in each one second. The data are analyzed from January to the end of March-2013. Maximum daily readings and monthly average readings of solar irradiance have been analyzed to optimize the output of photovoltaic solar modules. The results show that the system sizing of PV can be reduced by 12.5% if a tracking system is used instead of fixed orientation of PV modules.
Maximum power analysis of photovoltaic module in Ramadi city
Majid Shahatha Salim, Jassim Mohammed Najim, Salih Mohammed Salih
2013-01-01
Full Text Available Performance of photovoltaic (PV module is greatly dependent on the solar irradiance, operating temperature, and shading. Solar irradiance can have a significant impact on power output of PV module and energy yield. In this paper, a maximum PV power which can be obtain in Ramadi city (100km west of Baghdad is practically analyzed. The analysis is based on real irradiance values obtained as the first time by using Soly2 sun tracker device. Proper and adequate information on solar radiation and its components at a given location is very essential in the design of solar energy systems. The solar irradiance data in Ramadi city were analyzed based on the first three months of 2013. The solar irradiance data are measured on earth's surface in the campus area of Anbar University. Actual average data readings were taken from the data logger of sun tracker system, which sets to save the average readings for each two minutes and based on reading in each one second. The data are analyzed from January to the end of March-2013. Maximum daily readings and monthly average readings of solar irradiance have been analyzed to optimize the output of photovoltaic solar modules. The results show that the system sizing of PV can be reduced by 12.5% if a tracking system is used instead of fixed orientation of PV modules.
7 CFR 3560.202 - Establishing rents and utility allowances.
2010-01-01
... 7 Agriculture 15 2010-01-01 2010-01-01 false Establishing rents and utility allowances. 3560.202... Establishing rents and utility allowances. (a) General. Rents and utility allowances for rental units in Agency... Agency. (b) Agency approval. All rents and utility allowances set by borrowers are subject to...
Surface chemistry allows for abiotic precipitation of dolomite at low temperature
Roberts, Jennifer A.; Kenward, Paul A.; Fowle, David A.; Goldstein, Robert H.; Luis A. González; Moore, David S.
2013-01-01
Abundant in the geologic record, but scarce in modern environments below 50 °C, the mineral dolomite is used to interpret ancient fluid chemistry, paleotemperature, and is a major hydrocarbon reservoir rock. Because laboratory synthesis of abiotic dolomite had been unsuccessful, chemical mechanisms for precipitation are poorly constrained, and limit interpretations of its occurrence. Here we report the abiotic synthesis of dolomite at 25 °C, and demonstrate that carboxylated surfaces on organ...
The changes of holographic characteristics of photopolymer induced by temperature
Mingju Huang(黄明举); Huawen Yao(姚华文); Zhongyu Chen(陈仲裕); Lisong Hou(侯立松); Fuxi Gan(干福熹)
2003-01-01
The changes of holographic characteristics of photopolymer induced by temperature are studied experimentally. The results show that the exposure sensitivity increases with the increase of temperature. The maximum diffraction efficiency and the final maximum diffraction efficiency increase with the increase of temperature when the temperature is lower than Tg (glass transition temperature), while they decrease with the increase of temperature when the temperature is higher than Tg. The effect of the change of temperature on the saturation refractive index modulation is very weak.
Evaluation of Probable Maximum Precipitation and Flood under Climate Change in the 21st Century
Gangrade, S.; Kao, S. C.; Rastogi, D.; Ashfaq, M.; Naz, B. S.; Kabela, E.; Anantharaj, V. G.; Singh, N.; Preston, B. L.; Mei, R.
2016-12-01
Critical infrastructures are potentially vulnerable to extreme hydro-climatic events. Under a warming environment, the magnitude and frequency of extreme precipitation and flood are likely to increase enhancing the needs to more accurately quantify the risks due to climate change. In this study, we utilized an integrated modeling framework that includes the Weather Research Forecasting (WRF) model and a high resolution distributed hydrology soil vegetation model (DHSVM) to simulate probable maximum precipitation (PMP) and flood (PMF) events over Alabama-Coosa-Tallapoosa River Basin. A total of 120 storms were selected to simulate moisture maximized PMP under different meteorological forcings, including historical storms driven by Climate Forecast System Reanalysis (CFSR) and baseline (1981-2010), near term future (2021-2050) and long term future (2071-2100) storms driven by Community Climate System Model version 4 (CCSM4) under Representative Concentrations Pathway 8.5 emission scenario. We also analyzed the sensitivity of PMF to various antecedent hydrologic conditions such as initial soil moisture conditions and tested different compulsive approaches. Overall, a statistical significant increase is projected for future PMP and PMF, mainly attributed to the increase of background air temperature. The ensemble of simulated PMP and PMF along with their sensitivity allows us to better quantify the potential risks associated with hydro-climatic extreme events on critical energy-water infrastructures such as major hydropower dams and nuclear power plants.
Govatski, J. A.; da Luz, M. G. E.; Koehler, M.
2015-01-01
We study the geminated pair dissociation probability φ as function of applied electric field and temperature in energetically disordered nD media. Regardless nD, for certain parameters regions φ versus the disorder degree (σ) displays anomalous minimum (maximum) at low (moderate) fields. This behavior is compatible with a transport energy which reaches a maximum and then decreases to negative values as σ increases. Our results explain the temperature dependence of the persistent photoconductivity in C60 single crystals going through order-disorder transitions. They also indicate how an energetic disorder spatial variation may contribute to higher exciton dissociation in multicomponent donor/acceptor systems.
Maximum tunneling velocities in symmetric double well potentials
Manz, Jörn [State Key Laboratory of Quantum Optics and Quantum Optics Devices, Institute of Laser Spectroscopy, Shanxi University, 92, Wucheng Road, Taiyuan 030006 (China); Institut für Chemie und Biochemie, Freie Universität Berlin, Takustr. 3, 14195 Berlin (Germany); Schild, Axel [Institut für Chemie und Biochemie, Freie Universität Berlin, Takustr. 3, 14195 Berlin (Germany); Schmidt, Burkhard, E-mail: burkhard.schmidt@fu-berlin.de [Institut für Mathematik, Freie Universität Berlin, Arnimallee 6, 14195 Berlin (Germany); Yang, Yonggang, E-mail: ygyang@sxu.edu.cn [State Key Laboratory of Quantum Optics and Quantum Optics Devices, Institute of Laser Spectroscopy, Shanxi University, 92, Wucheng Road, Taiyuan 030006 (China)
2014-10-17
Highlights: • Coherent tunneling in one-dimensional symmetric double well potentials. • Potentials for analytical estimates in the deep tunneling regime. • Maximum velocities scale as the square root of the ratio of barrier height and mass. • In chemical physics maximum tunneling velocities are in the order of a few km/s. - Abstract: We consider coherent tunneling of one-dimensional model systems in non-cyclic or cyclic symmetric double well potentials. Generic potentials are constructed which allow for analytical estimates of the quantum dynamics in the non-relativistic deep tunneling regime, in terms of the tunneling distance, barrier height and mass (or moment of inertia). For cyclic systems, the results may be scaled to agree well with periodic potentials for which semi-analytical results in terms of Mathieu functions exist. Starting from a wavepacket which is initially localized in one of the potential wells, the subsequent periodic tunneling is associated with tunneling velocities. These velocities (or angular velocities) are evaluated as the ratio of the flux densities versus the probability densities. The maximum velocities are found under the top of the barrier where they scale as the square root of the ratio of barrier height and mass (or moment of inertia), independent of the tunneling distance. They are applied exemplarily to several prototypical molecular models of non-cyclic and cyclic tunneling, including ammonia inversion, Cope rearrangement of semibullvalene, torsions of molecular fragments, and rotational tunneling in strong laser fields. Typical maximum velocities and angular velocities are in the order of a few km/s and from 10 to 100 THz for our non-cyclic and cyclic systems, respectively, much faster than time-averaged velocities. Even for the more extreme case of an electron tunneling through a barrier of height of one Hartree, the velocity is only about one percent of the speed of light. Estimates of the corresponding time scales for
Efficiency at maximum power of a discrete feedback ratchet
Jarillo, Javier; Tangarife, Tomás; Cao, Francisco J.
2016-01-01
Efficiency at maximum power is found to be of the same order for a feedback ratchet and for its open-loop counterpart. However, feedback increases the output power up to a factor of five. This increase in output power is due to the increase in energy input and the effective entropy reduction obtained as a consequence of feedback. Optimal efficiency at maximum power is reached for time intervals between feedback actions two orders of magnitude smaller than the characteristic time of diffusion over a ratchet period length. The efficiency is computed consistently taking into account the correlation between the control actions. We consider a feedback control protocol for a discrete feedback flashing ratchet, which works against an external load. We maximize the power output optimizing the parameters of the ratchet, the controller, and the external load. The maximum power output is found to be upper bounded, so the attainable extracted power is limited. After, we compute an upper bound for the efficiency of this isothermal feedback ratchet at maximum power output. We make this computation applying recent developments of the thermodynamics of feedback-controlled systems, which give an equation to compute the entropy reduction due to information. However, this equation requires the computation of the probability of each of the possible sequences of the controller's actions. This computation becomes involved when the sequence of the controller's actions is non-Markovian, as is the case in most feedback ratchets. We here introduce an alternative procedure to set strong bounds to the entropy reduction in order to compute its value. In this procedure the bounds are evaluated in a quasi-Markovian limit, which emerge when there are big differences between the stationary probabilities of the system states. These big differences are an effect of the potential strength, which minimizes the departures from the Markovianicity of the sequence of control actions, allowing also to
Temperature Distribution in a Displacement Ventilated Room
Nielsen, Peter V.
The vertical temperature gradient is normally given as a linear temperature distribution between a minimum temperature close to the floor and a maximum temperature close to the ceiling. The minimum temperature can either be a constant fraction of a load dependent difference or it can be connected...
Speech processing using maximum likelihood continuity mapping
Hogden, John E. (Santa Fe, NM)
2000-01-01
Speech processing is obtained that, given a probabilistic mapping between static speech sounds and pseudo-articulator positions, allows sequences of speech sounds to be mapped to smooth sequences of pseudo-articulator positions. In addition, a method for learning a probabilistic mapping between static speech sounds and pseudo-articulator position is described. The method for learning the mapping between static speech sounds and pseudo-articulator position uses a set of training data composed only of speech sounds. The said speech processing can be applied to various speech analysis tasks, including speech recognition, speaker recognition, speech coding, speech synthesis, and voice mimicry.
Speech processing using maximum likelihood continuity mapping
Hogden, J.E.
2000-04-18
Speech processing is obtained that, given a probabilistic mapping between static speech sounds and pseudo-articulator positions, allows sequences of speech sounds to be mapped to smooth sequences of pseudo-articulator positions. In addition, a method for learning a probabilistic mapping between static speech sounds and pseudo-articulator position is described. The method for learning the mapping between static speech sounds and pseudo-articulator position uses a set of training data composed only of speech sounds. The said speech processing can be applied to various speech analysis tasks, including speech recognition, speaker recognition, speech coding, speech synthesis, and voice mimicry.
20 CFR 211.14 - Maximum creditable compensation.
2010-04-01
... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false Maximum creditable compensation. 211.14... CREDITABLE RAILROAD COMPENSATION § 211.14 Maximum creditable compensation. Maximum creditable compensation... Employment Accounts shall notify each employer of the amount of maximum creditable compensation applicable...
Theoretical Estimate of Maximum Possible Nuclear Explosion
Bethe, H. A.
1950-01-31
The maximum nuclear accident which could occur in a Na-cooled, Be moderated, Pu and power producing reactor is estimated theoretically. (T.R.H.) 2O82 Results of nuclear calculations for a variety of compositions of fast, heterogeneous, sodium-cooled, U-235-fueled, plutonium- and power-producing reactors are reported. Core compositions typical of plate-, pin-, or wire-type fuel elements and with uranium as metal, alloy, and oxide were considered. These compositions included atom ratios in the following range: U-23B to U-235 from 2 to 8; sodium to U-235 from 1.5 to 12; iron to U-235 from 5 to 18; and vanadium to U-235 from 11 to 33. Calculations were performed to determine the effect of lead and iron reflectors between the core and blanket. Both natural and depleted uranium were evaluated as the blanket fertile material. Reactors were compared on a basis of conversion ratio, specific power, and the product of both. The calculated results are in general agreement with the experimental results from fast reactor assemblies. An analysis of the effect of new cross-section values as they became available is included. (auth)
Proposed principles of maximum local entropy production.
Ross, John; Corlan, Alexandru D; Müller, Stefan C
2012-07-12
Articles have appeared that rely on the application of some form of "maximum local entropy production principle" (MEPP). This is usually an optimization principle that is supposed to compensate for the lack of structural information and measurements about complex systems, even systems as complex and as little characterized as the whole biosphere or the atmosphere of the Earth or even of less known bodies in the solar system. We select a number of claims from a few well-known papers that advocate this principle and we show that they are in error with the help of simple examples of well-known chemical and physical systems. These erroneous interpretations can be attributed to ignoring well-established and verified theoretical results such as (1) entropy does not necessarily increase in nonisolated systems, such as "local" subsystems; (2) macroscopic systems, as described by classical physics, are in general intrinsically deterministic-there are no "choices" in their evolution to be selected by using supplementary principles; (3) macroscopic deterministic systems are predictable to the extent to which their state and structure is sufficiently well-known; usually they are not sufficiently known, and probabilistic methods need to be employed for their prediction; and (4) there is no causal relationship between the thermodynamic constraints and the kinetics of reaction systems. In conclusion, any predictions based on MEPP-like principles should not be considered scientifically founded.
Maximum entropy production and plant optimization theories.
Dewar, Roderick C
2010-05-12
Plant ecologists have proposed a variety of optimization theories to explain the adaptive behaviour and evolution of plants from the perspective of natural selection ('survival of the fittest'). Optimization theories identify some objective function--such as shoot or canopy photosynthesis, or growth rate--which is maximized with respect to one or more plant functional traits. However, the link between these objective functions and individual plant fitness is seldom quantified and there remains some uncertainty about the most appropriate choice of objective function to use. Here, plants are viewed from an alternative thermodynamic perspective, as members of a wider class of non-equilibrium systems for which maximum entropy production (MEP) has been proposed as a common theoretical principle. I show how MEP unifies different plant optimization theories that have been proposed previously on the basis of ad hoc measures of individual fitness--the different objective functions of these theories emerge as examples of entropy production on different spatio-temporal scales. The proposed statistical explanation of MEP, that states of MEP are by far the most probable ones, suggests a new and extended paradigm for biological evolution--'survival of the likeliest'--which applies from biomacromolecules to ecosystems, not just to individuals.
Maximum likelihood continuity mapping for fraud detection
Hogden, J.
1997-05-01
The author describes a novel time-series analysis technique called maximum likelihood continuity mapping (MALCOM), and focuses on one application of MALCOM: detecting fraud in medical insurance claims. Given a training data set composed of typical sequences, MALCOM creates a stochastic model of sequence generation, called a continuity map (CM). A CM maximizes the probability of sequences in the training set given the model constraints, CMs can be used to estimate the likelihood of sequences not found in the training set, enabling anomaly detection and sequence prediction--important aspects of data mining. Since MALCOM can be used on sequences of categorical data (e.g., sequences of words) as well as real valued data, MALCOM is also a potential replacement for database search tools such as N-gram analysis. In a recent experiment, MALCOM was used to evaluate the likelihood of patient medical histories, where ``medical history`` is used to mean the sequence of medical procedures performed on a patient. Physicians whose patients had anomalous medical histories (according to MALCOM) were evaluated for fraud by an independent agency. Of the small sample (12 physicians) that has been evaluated, 92% have been determined fraudulent or abusive. Despite the small sample, these results are encouraging.
Maximum life spiral bevel reduction design
Savage, M.; Prasanna, M. G.; Coe, H. H.
1992-07-01
Optimization is applied to the design of a spiral bevel gear reduction for maximum life at a given size. A modified feasible directions search algorithm permits a wide variety of inequality constraints and exact design requirements to be met with low sensitivity to initial values. Gear tooth bending strength and minimum contact ratio under load are included in the active constraints. The optimal design of the spiral bevel gear reduction includes the selection of bearing and shaft proportions in addition to gear mesh parameters. System life is maximized subject to a fixed back-cone distance of the spiral bevel gear set for a specified speed ratio, shaft angle, input torque, and power. Significant parameters in the design are: the spiral angle, the pressure angle, the numbers of teeth on the pinion and gear, and the location and size of the four support bearings. Interpolated polynomials expand the discrete bearing properties and proportions into continuous variables for gradient optimization. After finding the continuous optimum, a designer can analyze near optimal designs for comparison and selection. Design examples show the influence of the bearing lives on the gear parameters in the optimal configurations. For a fixed back-cone distance, optimal designs with larger shaft angles have larger service lives.
Finding maximum JPEG image block code size
Lakhani, Gopal
2012-07-01
We present a study of JPEG baseline coding. It aims to determine the minimum storage needed to buffer the JPEG Huffman code bits of 8-bit image blocks. Since DC is coded separately, and the encoder represents each AC coefficient by a pair of run-length/AC coefficient level, the net problem is to perform an efficient search for the optimal run-level pair sequence. We formulate it as a two-dimensional, nonlinear, integer programming problem and solve it using a branch-and-bound based search method. We derive two types of constraints to prune the search space. The first one is given as an upper-bound for the sum of squares of AC coefficients of a block, and it is used to discard sequences that cannot represent valid DCT blocks. The second type constraints are based on some interesting properties of the Huffman code table, and these are used to prune sequences that cannot be part of optimal solutions. Our main result is that if the default JPEG compression setting is used, space of minimum of 346 bits and maximum of 433 bits is sufficient to buffer the AC code bits of 8-bit image blocks. Our implementation also pruned the search space extremely well; the first constraint reduced the initial search space of 4 nodes down to less than 2 nodes, and the second set of constraints reduced it further by 97.8%.
Maximum likelihood estimates of pairwise rearrangement distances.
Serdoz, Stuart; Egri-Nagy, Attila; Sumner, Jeremy; Holland, Barbara R; Jarvis, Peter D; Tanaka, Mark M; Francis, Andrew R
2017-06-21
Accurate estimation of evolutionary distances between taxa is important for many phylogenetic reconstruction methods. Distances can be estimated using a range of different evolutionary models, from single nucleotide polymorphisms to large-scale genome rearrangements. Corresponding corrections for genome rearrangement distances fall into 3 categories: Empirical computational studies, Bayesian/MCMC approaches, and combinatorial approaches. Here, we introduce a maximum likelihood estimator for the inversion distance between a pair of genomes, using a group-theoretic approach to modelling inversions introduced recently. This MLE functions as a corrected distance: in particular, we show that because of the way sequences of inversions interact with each other, it is quite possible for minimal distance and MLE distance to differently order the distances of two genomes from a third. The second aspect tackles the problem of accounting for the symmetries of circular arrangements. While, generally, a frame of reference is locked, and all computation made accordingly, this work incorporates the action of the dihedral group so that distance estimates are free from any a priori frame of reference. The philosophy of accounting for symmetries can be applied to any existing correction method, for which examples are offered. Copyright © 2017 Elsevier Ltd. All rights reserved.
(abstract) Cassini MLI Balnkets High-Temperature Exposure Tests
Lin, Edward I.; Stultz, James W.
1995-01-01
The trajectory required for the Cassini spacecraft to reach Saturn will subject the spacecraft to a 0.61 AU temperature environment at perihelion. Temperatures on some sunlit blanket surfaces at 0.61 AU can reach levels that are beyond the service capability of the conventional Mylar/Dacron net MLI. The majority of the blanket surfaces, however, will experience temperatures with an upper bound of 250(deg) C. The maximum allowable temperature for Mylar/Dacron net is determined to be 220(deg)C. Kapton can withstand temperatures in excess of 400(deg) C; however, the high cost of embossed Kapton relative to Mylar/Dacron net requires a baseline design which includes a standard layup and a high-temperature layup. The high-temperature layup is utilized at a limited number of locations, while at least 90% of the blankets are of the standard layup. The verification of both layups' capability to meet all temperature requirements has been accomplished by a comprehensive test program which addressed their high-temperature survivability, effective emittance, and optical and electrical properties. This paper focuses on the high-temperature exposure tests which helped define the hybrid standard layup, and which demonstrated the adequacy of both layups in withstanding their respective thermal environments.
High temperature performance of a piezoelectric micro cantilever for vibration energy harvesting
Arroyo, E.; Jia, Y.; Du, S.; Chen, ST; Seshia, A.
2016-11-01
Energy harvesters withstanding high temperatures could provide potentially unlimited energy to sensor nodes placed in harsh environments, where manual maintenance is difficult and costly. Experimental results on a classical microcantilever show a 67% drop of the maximum power when the temperature is increased up to 160 °C. This decrease is investigated using a lumped-parameters model which takes into account variations in material parameters with temperature, damping increase and thermal stresses induced by mismatched thermal coefficients in a composite cantilever. The model allows a description of the maximum power evolution as a function of temperature and input acceleration. Simulation results further show that an increase in damping and the apparition of thermal stresses are contributing to the power drop at 59% and 13% respectively.
Maximum SINR Synchronization Strategies in Multiuser Filter Bank Schemes
Pecile Francesco
2010-01-01
Full Text Available We consider synchronization in a multiuser filter bank uplink system with single-user detection. Perfect user synchronization is not the optimal choice as the intuition would suggest. To maximize performance the synchronization parameters have to be chosen to maximize the signal-to-interference-plus-noise ratio (SINR at each equalizer subchannel output. However, the resulting filter bank receiver structure becomes complex. Therefore, we consider two simplified synchronization metrics that are based on the maximization of the average SINR of a given user or the aggregate SINR of all users. Furthermore, a relaxation of the aggregate SINR metric allows implementing an efficient multiuser analysis filter bank. This receiver deploys two fractionally spaced analysis stages. Each analysis stage is efficiently implemented via a polyphase filter bank, followed by an extended discrete Fourier transform that allows the user frequency offsets to be partly compensated. Then, sub-channel maximum SINR equalization is used. We discuss the application of the proposed solution to Orthogonal Frequency Division Multiple Access (OFDMA and multiuser Filtered Multitone (FMT systems.
tmle : An R Package for Targeted Maximum Likelihood Estimation
Susan Gruber
2012-11-01
Full Text Available Targeted maximum likelihood estimation (TMLE is a general approach for constructing an efficient double-robust semi-parametric substitution estimator of a causal effect parameter or statistical association measure. tmle is a recently developed R package that implements TMLE of the effect of a binary treatment at a single point in time on an outcome of interest, controlling for user supplied covariates, including an additive treatment effect, relative risk, odds ratio, and the controlled direct effect of a binary treatment controlling for a binary intermediate variable on the pathway from treatment to the out- come. Estimation of the parameters of a marginal structural model is also available. The package allows outcome data with missingness, and experimental units that contribute repeated records of the point-treatment data structure, thereby allowing the analysis of longitudinal data structures. Relevant factors of the likelihood may be modeled or fit data-adaptively according to user specifications, or passed in from an external estimation procedure. Effect estimates, variances, p values, and 95% confidence intervals are provided by the software.
Boedeker, Peter
2017-01-01
Hierarchical linear modeling (HLM) is a useful tool when analyzing data collected from groups. There are many decisions to be made when constructing and estimating a model in HLM including which estimation technique to use. Three of the estimation techniques available when analyzing data with HLM are maximum likelihood, restricted maximum…
A Significant Population Signal in Iranian Temperature Records
Shouraseni Sen Roy
2016-01-01
Full Text Available We assembled daily maximum and minimum temperature records for 31 stations throughout Iran over the period 1961–2010. As with many other areas of the world, we found that both the maximum and minimum temperatures were increasing overall with the minimum temperatures increasing twice as fast as the maximum temperatures. We gathered population data for the stations near the beginning and end of the temperature records and found in all seasons and for both the maximum and minimum temperatures the magnitude of population growth positively influenced the temperature trends. However, unlike so many other studies, we found the strongest population growth signal in the winter for the maximum temperatures. We found evidence that this winter-season population-temperature signal is related snow cover. Our results illustrate that any number of processes are involved in explaining trends in historical maximum and minimum temperature records.
77 FR 76169 - Increase in Maximum Tuition and Fee Amounts Payable under the Post-9/11 GI Bill
2012-12-26
... AFFAIRS Increase in Maximum Tuition and Fee Amounts Payable under the Post-9/11 GI Bill AGENCY: Department... of the increase in the Post-9/11 GI Bill maximum tuition and fee amounts payable and the increase in.... SUPPLEMENTARY INFORMATION: For the 2011-2012 academic year, the Post-9/ 11 GI Bill allowed VA to pay the actual...
High temperature workability behaviour of a modified P92 steel
Carsi, Manuel; Ruano, Oscar A. [CENIM-CSIC, Madrid (Spain); Penalba, Felix [TECNALIA, San Sebastian (Spain); Rieiro, Ignaciao [Castilla-La Mancha Univ., Toledo (Spain). Dept. Matematicas
2011-11-15
The high temperature forming behaviour of a modified P92, type 9% Cr, steel is studied by means of torsion tests. The data obtained from these tests allowed correlation of the number of turns to failure, a measure of ductility, as a function of strain rate and temperature. In addition, the data were correlated by the Garofalo equation with a stress exponent of 4.78 and an activation energy of 390 kJ mol{sup -1}. This equation was used to predict the formability behaviour for the rolling process and also to determine the maximum forming efficiency and stability of the steel. A temperature of 1 140 C is found to give the optimum forming temperature. (orig.)
Impact of intake water temperatures on reticular temperatures of lactating dairy cows.
Bewley, J M; Grott, M W; Einstein, M E; Schutz, M M
2008-10-01
Automatic temperature recording may allow early detection of disease, estrus, heat stress, and the onset of calving. The phase IV Cattle Temperature Monitoring System (MaGiiX Inc., Post Falls, ID) utilizes a passive bolus equipped with a temperature sensor, a stationary panel reader to query the bolus, and software to collect, analyze, and display data. One potential limitation to collection of reticular temperatures is the effect of water temperature and consumption on recorded temperatures. Two replicated 3 x 3 Latin square experiments were conducted at the Purdue Dairy Research and Education Center to assess the impact of water intake on reticular temperatures using the Cattle Temperature Monitoring System. Nine high-producing, mid-lactation, second-parity cows with low somatic cell counts were selected. Before administering a water treatment, access to feed and water was restricted for at least 2 h. Baseline reticular temperatures were established from measurements before water intake. In experiment 1, treatments were 25.2 kg of hot water (34.3 degrees C +/- 1.0), warm water (18.2 degrees C +/- 0.4), or cold water (7.6 degrees C +/- 0.4). In experiment 2, treatments were 18.9 kg of body-temperature water (38.9 degrees C +/- 0.2), cold water (5.1 degrees C +/- 0.4), or control (no water). Following water intake, reticular temperatures were collected for 3 h. In experiment 1, an initial dramatic decrease in reticular temperature was observed followed by a gradual increase toward baseline. Least squares means for maximum drop in temperature were 8.5 +/- 0.5, 6.9 +/- 0.5, and 2.2 +/- 0.5 degrees C for cold, warm, and hot water treatments, respectively. Yet at 3 h, reticular temperatures did not return to the baseline. In experiment 2, control cows remained within the baseline confidence interval through the observation period, and cows receiving body temperature water experienced an initial decrease in temperature (0.4 +/- 0.2 degrees C) with a return to within the
Maximum likelihood molecular clock comb: analytic solutions.
Chor, Benny; Khetan, Amit; Snir, Sagi
2006-04-01
Maximum likelihood (ML) is increasingly used as an optimality criterion for selecting evolutionary trees, but finding the global optimum is a hard computational task. Because no general analytic solution is known, numeric techniques such as hill climbing or expectation maximization (EM), are used in order to find optimal parameters for a given tree. So far, analytic solutions were derived only for the simplest model--three taxa, two state characters, under a molecular clock. Four taxa rooted trees have two topologies--the fork (two subtrees with two leaves each) and the comb (one subtree with three leaves, the other with a single leaf). In a previous work, we devised a closed form analytic solution for the ML molecular clock fork. In this work, we extend the state of the art in the area of analytic solutions ML trees to the family of all four taxa trees under the molecular clock assumption. The change from the fork topology to the comb incurs a major increase in the complexity of the underlying algebraic system and requires novel techniques and approaches. We combine the ultrametric properties of molecular clock trees with the Hadamard conjugation to derive a number of topology dependent identities. Employing these identities, we substantially simplify the system of polynomial equations. We finally use tools from algebraic geometry (e.g., Gröbner bases, ideal saturation, resultants) and employ symbolic algebra software to obtain analytic solutions for the comb. We show that in contrast to the fork, the comb has no closed form solutions (expressed by radicals in the input data). In general, four taxa trees can have multiple ML points. In contrast, we can now prove that under the molecular clock assumption, the comb has a unique (local and global) ML point. (Such uniqueness was previously shown for the fork.).
Moacyr Jorge Elias
2011-04-01
Full Text Available A bromelina, enzima presente no abacaxi, hidrolisa ligações peptídicas das proteínas; tem aplicação em diversas áreas envolvendo alimentos e medicina. Visando o aproveitamento da bromelina recuperada, a partir dos resíduos da industrialização do fruto(variedade pérola, foram pesquisadas condições de pH e temperatura para maior atividade, empregando caseína como substrato. O extrato foi obtido pela trituração da casca e do talo interno do fruto. A atividade foi expressa em mmol tirosina L-1 min.-1 pela absorbância a280 nm dos aminoácidos aromáticos gerados na hidrólise da caseína. Os ensaios foram efetuados em duplicata para duas relações enzima/substrato: 1/25 e 1/125 (em massa. Foi estabelecido um planejamento experimental em estrela tendo como ponto central pH em7,0 e temperatura de 35°C. Os resultados foram tratados empregando o aplicativo computacional MINITAB 15 da Minitab Inc. que forneceu as equações do modelo e as superfícies de resposta. As equações foram tratadas matematicamente (cálculo diferencial, fornecendo gráficos da melhor atividade em função da temperatura. Observou-se perda daatividade enzimática com a elevação da temperatura para relação 1/25, atribuída à maior presença de enzima livre em comparação com a relação 1/125.Bromelain, the enzyme found in pineapple, hydrolyzes proteins’ peptide bonds, has several applications in the food industry and in medicine. Temperature and pH conditions for highest activity with casein as substrate were investigated from the bromelain recovered from industrialized pineapple (‘pérola’ variety fruit residues. Extract was obtained by grinding fruit rind and its internal stem. The activity was expressed in mmol tyrosine L-1 min.-1 by absorbance at 280 nm of aromatic amino acids produced in casein hydrolysis. Assays were undertaken in duplicate for two enzyme/substrate with ratios: 1/25 and 1/125 (mass. Eight-pointed experimental design was
27 CFR 20.24 - Allowance of claims.
2010-04-01
... OF THE TREASURY LIQUORS DISTRIBUTION AND USE OF DENATURED ALCOHOL AND RUM Administrative Provisions Authorities § 20.24 Allowance of claims. The appropriate TTB officer is authorized to allow claims for...
27 CFR 22.23 - Allowance of claims.
2010-04-01
... OF THE TREASURY LIQUORS DISTRIBUTION AND USE OF TAX-FREE ALCOHOL Administrative Provisions Authorities § 22.23 Allowance of claims. The appropriate TTB officer is authorized to allow claims for...
2010-10-01
... low-income children in families with income from 101 to 150 percent of the FPL. 457.555 Section 457... low-income children in families with income from 101 to 150 percent of the FPL. (a) Non-institutional services. For targeted low-income children whose family income is from 101 to 150 percent of the FPL,...
Perry, J. L.
2016-01-01
As the Space Station Freedom program transitioned to become the International Space Station (ISS), uncertainty existed concerning the performance capabilities for U.S.- and Russian-provided trace contaminant control (TCC) equipment. In preparation for the first dialogue between NASA and Russian Space Agency personnel in Moscow, Russia, in late April 1994, an engineering analysis was conducted to serve as a basis for discussing TCC equipment engineering assumptions as well as relevant assumptions on equipment offgassing and cabin air quality standards. The analysis presented was conducted as part of the efforts to integrate Russia into the ISS program via the early ISS Multilateral Medical Operations Panel's Air Quality Subgroup deliberations. This analysis, served as a basis for technical deliberations that established a framework for TCC system design and operations among the ISS program's international partners that has been instrumental in successfully managing the ISS common cabin environment.
Hydrodynamic equations for electrons in graphene obtained from the maximum entropy principle
Barletti, Luigi, E-mail: luigi.barletti@unifi.it [Dipartimento di Matematica e Informatica “Ulisse Dini”, Università degli Studi di Firenze, Viale Morgagni 67/A, 50134 Firenze (Italy)
2014-08-15
The maximum entropy principle is applied to the formal derivation of isothermal, Euler-like equations for semiclassical fermions (electrons and holes) in graphene. After proving general mathematical properties of the equations so obtained, their asymptotic form corresponding to significant physical regimes is investigated. In particular, the diffusive regime, the Maxwell-Boltzmann regime (high temperature), the collimation regime and the degenerate gas limit (vanishing temperature) are considered.
50 CFR 665.127 - Allowable gear and gear restrictions.
2010-10-01
... 50 Wildlife and Fisheries 9 2010-10-01 2010-10-01 false Allowable gear and gear restrictions. 665... Fisheries § 665.127 Allowable gear and gear restrictions. (a) American Samoa coral reef ecosystem MUS may be taken only with the following allowable gear and methods: (1) Hand harvest; (2) Spear; (3) Slurp gun;...
50 CFR 665.427 - Allowable gear and gear restrictions.
2010-10-01
... 50 Wildlife and Fisheries 9 2010-10-01 2010-10-01 false Allowable gear and gear restrictions. 665... Archipelago Fisheries § 665.427 Allowable gear and gear restrictions. (a) Mariana coral reef ecosystem MUS may be taken only with the following allowable gear and methods: (1) Hand harvest; (2) Spear; (3)...
50 CFR 665.227 - Allowable gear and gear restrictions.
2010-10-01
... 50 Wildlife and Fisheries 9 2010-10-01 2010-10-01 false Allowable gear and gear restrictions. 665... Fisheries § 665.227 Allowable gear and gear restrictions. (a) Hawaii coral reef ecosystem MUS may be taken only with the following allowable gear and methods: (1) Hand harvest; (2) Spear; (3) Slurp gun;...
14 CFR 151.125 - Allowable advance planning costs.
2010-01-01
... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Allowable advance planning costs. 151.125... (CONTINUED) AIRPORTS FEDERAL AID TO AIRPORTS Rules and Procedures for Advance Planning and Engineering Proposals § 151.125 Allowable advance planning costs. (a) The United States' share of the allowable costs of...