Case Report: Magnetically retained silicone facial prosthesis ...

African Journals Online (AJOL)

Prosthetic camouflaging of facial defects and use of silicone maxillofacial material are the alternatives to the surgical retreatment. Silicone elastomers provide more options to clinician for customization of the facial prosthesis which is simple, esthetically good when coupled with bio magnets for retention. Key words: Magnet ...

Dielectric elastomers, with very high dielectric permittivity, based on silicone and ionic interpenetrating networks

DEFF Research Database (Denmark)

Yu, Liyun; Madsen, Frederikke Bahrt; Hvilsted, Søren

2015-01-01

permittivity and the Young's modulus of the elastomer. One system that potentially achieves this involves interpenetrating polymer networks (IPNs), based on commercial silicone elastomers and ionic networks from amino- and carboxylic acid-functional silicones. The applicability of these materials as DEs...... are obtained while dielectric breakdown strength and Young's modulus are not compromised. These good overall properties stem from the softening effect and very high permittivity of ionic networks – as high as ε′ = 7500 at 0.1 Hz – while the silicone elastomer part of the IPN provides mechanical integrity...

Voltage-stabilised elastomers with increased relative permittivity and high electrical breakdown strength by means of phase separating binary copolymer blends of silicone elastomers

DEFF Research Database (Denmark)

A Razak, Aliff Hisyam; Yu, Liyun; Skov, Anne Ladegaard

2017-01-01

Increased electrical breakdown strength and increased dielectric permittivity of silicone-based dielectric elastomers are achieved by means of the addition of so-called voltage-stabilisers prepared from PDMS–PPMS copolymers as well as PDMS–PEG copolymers in order to compensate for the negative...... effect of softness on electrical stability of silicone elastomers. The voltage-stabilised elastomer, incorporating a high-permittivity PDMS–PEG copolymer, possesses increased relative permittivity, high electrical breakdown strength, excellent network integrity and low dielectric loss and paves the way...

Electromechanical response of silicone dielectric elastomers

Science.gov (United States)

Cârlescu, V.; Prisăcaru, G.; Olaru, D.

2016-08-01

This paper presents an experimental technique to investigate the electromechanical properties of silicone dielectric elastomers actuated with high DC electric fields. A non-contact measurement technique is used to capture and monitor the thickness strain (contraction) of a circular film placed between two metallic disks electrodes. Two active fillers such as silica (10, 15 and 30 wt%) and barium titanate (5 and 15 wt%) were incorporated in order to increase the actuation performance. Thickness strain was measured at HV stimuli up to 4.5 kV and showed a quadratic dependence against applied electric field indicating that the induced strain is triggered by the Maxwell effect and/or electrostriction phenomenon as reported in literature. The actuation process evidences a rapid contraction upon HV activation and a slowly relaxation when the electrodes are short-circuit due to visco-elastic nature of elastomers. A maximum of 1.22 % thickness strain was obtained at low actuating field intensity (1.5 V/pm) comparable with those reported in literature for similar dielectric elastomer materials.

Effect of light aging on silicone-resin bond strength in maxillofacial prostheses.

Science.gov (United States)

Polyzois, Gregory; Pantopoulos, Antonis; Papadopoulos, Triantafillos; Hatamleh, Muhanad

2015-04-01

The aim of this study was to investigate the effect of accelerated light aging on bond strength of a silicone elastomer to three types of denture resin. A total of 60 single lap joint specimens were fabricated with auto-, heat-, and photopolymerized (n = 20) resins. An addition-type silicone elastomer (Episil-E) was bonded to resins treated with the same primer (A330-G). Thirty specimens served as controls and were tested after 24 hours, and the remaining were aged under accelerated exposure to daylight for 546 hours (irradiance 765 W/m(2) ). Lap shear joint tests were performed to evaluate bond strength at 50 mm/min crosshead speed. Two-way ANOVA and Tukey's test were carried out to detect statistical significance (p Accelerated light aging for 546 hours affects the bond strength of an addition-type silicone elastomer to three different denture resins. The bond strength significantly increased after aging for photo- and autopolymerized resins. All the bonds failed adhesively. © 2014 by the American College of Prosthodontists.

Silicone elastomers with superior softness and dielectric properties

DEFF Research Database (Denmark)

Yu, Liyun; Madsen, Frederikke Bahrt; Zakaria, Shamsul Bin

Dielectric elastomers (DEs) change their shape and size under a high voltage or reversibly generate a high voltage when deformed. The obstacle of high driving voltages, however, limits the commercial viability of the technology at present. Driving voltage can be lowered by decreasing the Young......’s modulus and increasing the dielectric permittivity of silicone elastomers. One such prominent method of modifying the properties is by adding suitable additives. [1] The major drawbacks for adding solid fillers are agglomeration and increasing stiffness which is often accompanied by the decrease...... were determined by NMR and morphology structures were investigated by optical microscopy. The resulting elastomers were evaluated with respect to their dielectric permittivity, tear and tensile strengths, as well as electrical breakdown.The breakdown strength increased at low amounts of additives...

Bimodal condensation silicone elastomers as dielectric elastomers

DEFF Research Database (Denmark)

Yu, Liyun; Madsen, Frederikke Bahrt; Skov, Anne Ladegaard

Lately, dielectric elastomers (DEs) which consist of an elastomer sandwiched between electrodes on both sides, have gained interest as materials for actuators, generators, and sensors. An ideal elastomer for DE uses is characterized by high extensibility, flexibility and good mechanical fatigue...... elastomers were prepared by mixing different mass ratios (9:1, 8:2, 7:3, 6:4, 5:5, 4:6) between long polydimethylsiloxane (PDMS) chains and short PDMS chains. The resulting elastomers were investigated with respect to their rheology, dielectric properties, tensile strength, electrical breakdown, as well.......Moreover, a series of elastomers with the same mass ratio (7:3) between long and short PDMS chains were made at different humidity (90%, 70%, 50%, 30%, 10%) at 23oC. The dielectric and mechincal properties of the resulting elastomers were shown to depend strongly on the atmospheric humidity level.In addition...

Silicone elastomers with high dielectric permittivity and high dielectric breakdown strength based on dipolar copolymers

DEFF Research Database (Denmark)

Madsen, Frederikke Bahrt; Yu, Liyun; Daugaard, Anders Egede

2014-01-01

Dielectric elastomers (DES) are a promising new transducer technology, but high driving voltages limit their current commercial potential. One method used to lower driving voltage is to increase dielectric permittivity of the elastomer. A novel silicone elastomer system with high dielectric...

Optimization Techniques for Improving the Performance of Silicone-Based Dielectric Elastomers

DEFF Research Database (Denmark)

Skov, Anne Ladegaard; Yu, Liyun

2017-01-01

the electro-mechanical performance of dielectric elastomers are highlighted. Various optimization methods for improved energy transduction are investigated and discussed, with special emphasis placed on the promise each method holds. The compositing and blending of elastomers are shown to be simple, versatile...... methods that can solve a number of optimization issues. More complicated methods, involving chemical modification of the silicone backbone as well as controlling the network structure for improved mechanical properties, are shown to solve yet more issues. From the analysis, it is obvious...... that there is not a single optimization technique that will lead to the universal optimization of dielectric elastomer films, though each method may lead to elastomers with certain features, and thus certain potentials....

Mechanical and Electrical Ageing Effects on the Long-Term Stretching of Silicone Dielectric Elastomers with Soft Fillers

DEFF Research Database (Denmark)

Madsen, Frederikke Bahrt; Zakaria, Shamsul Bin; Yu, Liyun

2016-01-01

Dielectric elastomer materials for actuators need to be soft and stretchable while possessing high dielectric permittivity. Soft silicone elastomers can be obtained through the use of silicone oils, while enhanced permittivity can be obtained through the use of dipolar groups on the polymer backb...

Effect of different types of disinfection solution and aging on the hardness and colour stability of maxillofacial silicone elastomers.

Science.gov (United States)

Cevik, Pinar; Yildirim-Bicer, Arzu Z

2017-11-09

Understanding the effect of aging and different disinfecting agents on the physical properties of pigmented maxillofacial silicones may help eliminate the current uncertainty as to the best follow-up suggestions for the patients treated with silicone prostheses. One hundred fifty specimens (14 × 2 mm) were evaluated for colour and 75 specimens (30 × 10 mm) for hardness (total, 225 specimens). Five specimens were used for hardness testing in each disinfecting solution while 10 silicone specimens were used for colour evaluation. The samples were separated into 5 groups and the initial hardness and colour evaluations were performed and placed in disinfectant solution (neutral soap, effervescent tablet, 0.2% chlorhexidine, 4% chlorhexidine, sodium hypochlorite). A second set of colour and hardness measurements was taken after 48 hours of disinfection and 1,008 hours of artificial aging in a QUV-accelerated weathering tester. Two-way and 1-way analysis of variance with Tukey tests and paired t-test were used for statistical analysis (α = 0.05). Before artificial aging, the hardness value of the red pigment group was found to be significantly lower than that of the brown pigment group. After aging, the lowest Shore A value was seen in the neutral soap group, while the highest was seen in the effervescent tablet. Based on the results of this study, chlorohexidine 0.2% was found to be most suitable agent for disinfection of the prostheses. Washing with neutral soap caused loss of pigment from the surface of the silicones. Sodium hypochlorite was found to have a colour-fading effect on silicone specimens.

Inkjet 3D printing of UV and thermal cure silicone elastomers for dielectric elastomer actuators

Science.gov (United States)

McCoul, David; Rosset, Samuel; Schlatter, Samuel; Shea, Herbert

2017-12-01

Dielectric elastomer actuators (DEAs) are an attractive form of electromechanical transducer, possessing high energy densities, an efficient design, mechanical compliance, high speed, and noiseless operation. They have been incorporated into a wide variety of devices, such as microfluidic systems, cell bioreactors, tunable optics, haptic displays, and actuators for soft robotics. Fabrication of DEA devices is complex, and the majority are inefficiently made by hand. 3D printing offers an automated and flexible manufacturing alternative that can fabricate complex, multi-material, integrated devices consistently and in high resolution. We present a novel additive manufacturing approach to DEA devices in which five commercially available, thermal and UV-cure DEA silicone rubber materials have been 3D printed with a drop-on-demand, piezoelectric inkjet system. Using this process, 3D structures and high-quality silicone dielectric elastomer membranes as thin as 2 μm have been printed that exhibit mechanical and actuation performance at least as good as conventionally blade-cast membranes. Printed silicone membranes exhibited maximum tensile strains of up to 727%, and DEAs with printed silicone dielectrics were actuated up to 6.1% area strain at a breakdown strength of 84 V μm-1 and also up to 130 V μm-1 at 2.4% strain. This approach holds great potential to manufacture reliable, high-performance DEA devices with high throughput.

Degradation patterns of silicone-based dielectric elastomers in electrical fields

DEFF Research Database (Denmark)

Yu, Liyun; Madsen, Frederikke Bahrt; Skov, Anne Ladegaard

2017-01-01

. This shortcoming has been attempted optimized through different approaches during recent years. Material optimization with the sole purpose of increasing the dielectric permittivity may lead to the introduction of problematic phenomena such as premature electrical breakdown due to high leakage currents of the thin...... elastomer film. Within this work, electrical breakdown phenomena of various types of permittivity-enhanced silicone elastomers are investigated. Results showed that different types of polymer backbone chemistries lead to differences in electrical breakdown patterns, which were revealed through SEM imaging...

Soft Functional Silicone Elastomers with High Dielectric Permittivty: Simple Additives vs. Cross-Linked Synthesized Copolymers

DEFF Research Database (Denmark)

Madsen, Frederikke Bahrt; Yu, Liyun; Skov, Anne Ladegaard

Though dielectric elastomers (DEs) have many favorable properties, the issue of high driving voltages limits the commercial viability of the technology. Improved actuation at lower voltages can be obtained by decreasing the Young’s modulus and/or decreasing the dielectric permittivity of the elas......Though dielectric elastomers (DEs) have many favorable properties, the issue of high driving voltages limits the commercial viability of the technology. Improved actuation at lower voltages can be obtained by decreasing the Young’s modulus and/or decreasing the dielectric permittivity...... of the elastomer. A decrease in Young’s modulus, however, is often accompanied by the loss of mechanical stability and thereby the lifetime of the DE whereas addition of high permittivity fillers such as metal oxides often increases Young’s modulus such that improved actuation is not accomplished. New soft...... silicone elastomers with high dielectric permittivity were prepared through the use of chloropropyl-functional silicones. One method was through the synthesis of modular cross-linkable chloropropyl-functional copolymers that allow for a high degree of chemical freedom such that a tuneable silicone...

Electrical breakdown phenomena of dielectric elastomers

DEFF Research Database (Denmark)

Mateiu, Ramona Valentina; Yu, Liyun; Skov, Anne Ladegaard

2017-01-01

Silicone elastomers have been heavily investigated as candidates for dielectric elastomers and are as such almost ideal candidates with their inherent softness and compliance but they suffer from low dielectric permittivity. This shortcoming has been sought optimized by many means during recent...... years. However, optimization with respect to the dielectric permittivity solely may lead to other problematic phenomena such as premature electrical breakdown. In this work, we investigate the electrical breakdown phenomena of various types of permittivity-enhanced silicone elastomers. Two types...... of silicone elastomers are investigated and different types of breakdown are discussed. Furthermore the use of voltage stabilizers in silicone-based dielectric elastomers is investigated and discussed....

Silicone rubbers for dielectric elastomers with improved dielectric and mechanical properties as a result of substituting silica with titanium dioxide

DEFF Research Database (Denmark)

Yu, Liyun; Skov, Anne Ladegaard

2016-01-01

One prominent method of modifying the properties of dielectric elastomers (DEs) is by adding suitable metal oxide fillers. However, almost all commercially available silicone elastomers are already heavily filled with silica to reinforce the otherwise rather weak silicone network and the resulting...... and dynamic viscosity. Filled silicone elastomers with high loadings of nano-sized titanium dioxide (TiO2) particles were also studied. The best overall performing formulation had 35 wt.% TiO2 nanoparticles in the POWERSIL® XLR LSR, where the excellent ensemble of relative dielectric permittivity of 4.9 at 0...

Electrical behaviour of a silicone elastomer under simulated space environment

International Nuclear Information System (INIS)

Roggero, A; Dantras, E; Paulmier, T; Rejsek-Riba, V; Tonon, C; Dagras, S; Balcon, N; Payan, D

2015-01-01

The electrical behavior of a space-used silicone elastomer was characterized using surface potential decay and dynamic dielectric spectroscopy techniques. In both cases, the dielectric manifestation of the glass transition (dipole orientation) and a charge transport phenomenon were observed. An unexpected linear increase of the surface potential with temperature was observed around T g in thermally-stimulated potential decay experiments, due to molecular mobility limiting dipolar orientation in one hand, and 3D thermal expansion reducing the materials capacitance in the other hand. At higher temperatures, the charge transport process, believed to be thermally activated electron hopping with an activation energy of about 0.4 eV, was studied with and without the silica and iron oxide fillers present in the commercial material. These fillers were found to play a preponderant role in the low-frequency electrical conductivity of this silicone elastomer, probably through a Maxwell–Wagner–Sillars relaxation phenomenon. (paper)

A new soft dielectric silicone elastomer matrix with high mechanical integrity and low losses

DEFF Research Database (Denmark)

Madsen, Frederikke Bahrt; Yu, Liyun; Daugaard, Anders Egede

2015-01-01

Though dielectric elastomers (DEs) have many favourable properties, the issue of high driving voltages limits the commercial viability of the technology. Driving voltage can be lowered by decreasing the Young's modulus and increasing the dielectric permittivity of silicone elastomers. A decrease...... in Young's modulus, however, is often accompanied by the loss of mechanical stability and thereby the lifetime of the DE. A new soft elastomer matrix, with no loss of mechanical stability and high dielectric permittivity, was prepared through the use of alkyl chloride-functional siloxane copolymers...

Design of Elastomer Structure to Facilitate Incorporation of Expanded Graphite in Silicones Without Compromising Electromechanical Integrity

DEFF Research Database (Denmark)

Hassouneh, Suzan Sager; Daugaard, Anders Egede; Skov, Anne Ladegaard

2015-01-01

The development of elastomer materials with a high dielectric permittivity has attracted increased interest over the past years due to their use in, for example, dielectric elastomers. For this particular use, both the electrically insulating properties - as well as the mechanical properties......-functional crosslinker, which allows for development of a suitable network matrix. The dielectric permittivity was increased by almost a factor of 4 compared to a benchmark silicone elastomer....

Novel scalable silicone elastomer and poly(2-hydroxyethyl methacrylate) (PHEMA) composite materials for tissue engineering and drug delivery applications

DEFF Research Database (Denmark)

Mohanty, Soumyaranjan; Hemmingsen, Mette; Wojcik, Magdalena

2013-01-01

material with increased hydrophilicity in regard to virgin silicone elastomer, making it suitable as a scaffold for tissue engineering and with the concomitant possibility for delivering drug from the scaffold to the tissue. Interpenetrating polymer networks (IPNs) of silicone elastomer and PHEMA......In recent years hydrogels have received increasing attention as potential materials for applications in regenerative medicine. They can be used for scaffold materials providing structural integrity to tissue constructs, for controlled delivery of drugs and proteins to cell and tissues......, and for support materials in tissue growth. However, the real challenge is to obtain sufficiently good mechanical properties of the hydrogel. The present study shows the combination of two normally non-compatible materials, silicone elastomer and poly(2-hydroxyethyl methacrylate) (PHEMA), into a novel composite...

A study of the dynamic flammability of radiation cross-linked flame-retardant HDPE/EPDM/silicon-elastomer compound

Energy Technology Data Exchange (ETDEWEB)

Jia, Shaojin E-mail: jiashaojin2@yahoo.com.cn; Zhang Zhicheng E-mail: zczhang@ustc.edu.cn; Du Zhiwen; Teng Renrui; Wang Zhengzhou

2003-04-01

A dynamic flammability study of flame-retardant compound consisting of HDPE, EPDM and silicon elastomer blended with additives, as wire and cable insulation was made before and after irradiation. The data of RHR, EHC, SEC and the concentration of CO and CO{sub 2} from cone colorimeter shown in the burning process were accessed. By blending silicon elastomer, CO release rate was reduced and the thermal endurance was improved. Oxygen index, mechanical property, morphology of the char formed in dynamical flame and thermal stability were also investigated.

A study of the dynamic flammability of radiation cross-linked flame-retardant HDPE/EPDM/silicon-elastomer compound

International Nuclear Information System (INIS)

Jia, Shaojin; Zhang Zhicheng; Du Zhiwen; Teng Renrui; Wang Zhengzhou

2003-01-01

A dynamic flammability study of flame-retardant compound consisting of HDPE, EPDM and silicon elastomer blended with additives, as wire and cable insulation was made before and after irradiation. The data of RHR, EHC, SEC and the concentration of CO and CO 2 from cone colorimeter shown in the burning process were accessed. By blending silicon elastomer, CO release rate was reduced and the thermal endurance was improved. Oxygen index, mechanical property, morphology of the char formed in dynamical flame and thermal stability were also investigated

Color stability of maxillofacial silicone with nanoparticle pigment and opacifier submitted to disinfection and artificial aging.

Science.gov (United States)

Filié Haddad, Marcela; Coelho Goiato, Marcelo; Micheline Dos Santos, Daniela; Moreno, Amália; Filipe D'almeida, Nuno; Alves Pesqueira, Aldiéris

2011-09-01

The purpose of this study was to evaluate the color stability of a maxillofacial elastomer with the addition of a nanoparticle pigment and∕or an opacifier submitted to chemical disinfection and artificial aging. Specimens were divided into four groups (n = 30): group I: silicone without pigment or opacifier, group II: ceramic powder pigment, group III: Barium sulfate (BaSO(4)) opacifier, and group IV: ceramic powder and BaSO(4) opacifier. Specimens of each group (n = 10) were disinfected with effervescent tablets, neutral soap, or 4% chlorhexidine gluconate. Disinfection was done three times a week during two months. Afterward, specimens were submitted to different periods of artificial aging. Color evaluation was initially done, after 60 days (disinfection period) and after 252, 504, and 1008 h of artificial aging with aid of a reflection spectrophotometer. Data were analyzed by three-way ANOVA and Tukey test (α = 0.05). The isolated factor disinfection did not statistically influence the values of color stability among groups. The association between pigment and BaSO(4) opacifier (GIV) was more stable in relationship to color change (△E). All values of △E obtained, independent of the disinfectant and the period of artificial aging, were considered acceptable in agreement with the norms presented in literature.

Improving bondability to RTV silicone elastomer using rf-activated gas

International Nuclear Information System (INIS)

Bellah, J.L.

1979-05-01

The effects of an rf-activated gas (plasma) on the bondability to RTV silicone elastomer were studied. Processing guidelines were developed, and a method was sought to satisfactorily bond RTV to the walls of a machined aluminum casting and to provide a surface on the RTV which would best accept bonding to an epoxy encapsulant. Processing parameters, such as gas type and flow rate, reaction chamber pressure, and rf power level, were developed

Effects of Hypervelocity Impacts on Silicone Elastomer Seals and Mating Aluminum Surfaces

Science.gov (United States)

deGroh, Henry C., III; Steinetz, Bruce M.

2009-01-01

While in space silicone based elastomer seals planned for use on NASA's Crew Exploration Vehicle (CEV) are exposed to threats from micrometeoroids and orbital debris (MMOD). An understanding of these threats is required to assess risks to the crew, the CEV orbiter, and missions. An Earth based campaign of hypervelocity impacts on small scale seal rings has been done to help estimate MMOD threats to the primary docking seal being developed for the Low Impact Docking System (LIDS). LIDS is being developed to enable the CEV to dock to the ISS (International Space Station) or to Altair (NASA's next lunar lander). The silicone seal on LIDS seals against aluminum alloy flanges on ISS or Altair. Since the integrity of a seal depends on both sealing surfaces, aluminum targets were also impacted. The variables considered in this study included projectile mass, density, speed, incidence angle, seal materials, and target surface treatments and coatings. Most of the impacts used a velocity near 8 km/s and spherical aluminum projectiles (density = 2.7 g/cubic cm), however, a few tests were done near 5.6 km/s. Tests were also performed using projectile densities of 7.7, 2.79, 2.5 or 1.14 g/cubic cm. Projectile incidence angles examined included 0 deg, 45 deg, and 60 deg from normal to the plane of the target. Elastomer compounds impacted include Parker's S0383-70 and Esterline's ELA-SA-401 in the as received condition, or after an atomic oxygen treatment. Bare, anodized and nickel coated aluminum targets were tested simulating the candidate mating seal surface materials. After impact, seals and aluminum plates were leak tested: damaged seals were tested against an undamaged aluminum plate; and undamaged seals were placed at various locations over craters in aluminum plates. It has been shown that silicone elastomer seals can withstand an impressive level of damage before leaking beyond allowable limits. In general on the tests performed to date, the diameter of the crater in

Green silicone elastomer obtained from a counterintuitively stable mixture of glycerol and PDMS

DEFF Research Database (Denmark)

Mazurek, P.; Hvilsted, S.; Skov, A. L.

2016-01-01

A green and cheap silicone-based elastomer has been developed. Through the simple mixing-in of biodiesel-originating glycerol into commercially available polydimethylsiloxane (PDMS) pre-polymer, a glycerol-in-PDMS emulsion was produced. This counterintuitively stable mixture became a basis...... for obtaining elastomeric composites with uniformly distributed glycerol droplets. Various compositions, containing from 0 to 140 parts of glycerol per 100 parts of PDMS by weight, were prepared and investigated in terms of ATR-FTIR, broadband dielectric spectroscopy, mechanical properties as well as optical......, even in the presence of very high loadings. The conducted experiments highlight the great potential of this new type of elastomer and reveal some possible applications....

Optimisation of Silicone-based Dielectric Elastomer Transducers by Means of Block Copolymers - Synthesis and Compounding

DEFF Research Database (Denmark)

A Razak, Aliff Hisyam

through the use of a multi-walled carbon nanotube (MWCNT) in a PDMS-PEG matrix as a compliant electrode of dielectric elastomers. The conductive PDMS-PEG copolymer was incorporated with surface-treated MWCNT, in order to obtain highly conductive elastomer. The prepared sample with 4 parts per hundred...... enhancing the electrical breakdown strength of silicone by using an aromatic voltage stabiliser. Here, polyphenylmethylsiloxane (PPMS), which contained aromatic voltage stabilisers, was bonded covalently to PDMS through a hydrosilylation reaction obtaining PDMS-PPMS copolymers. The synthesised copolymers...

A simple method for reducing inevitable dielectric loss in high-permittivity dielectric elastomers

DEFF Research Database (Denmark)

Madsen, Frederikke Bahrt; Yu, Liyun; Mazurek, Piotr Stanislaw

2016-01-01

elastomer matrix, with high dielectric permittivity and a low Young's modulus, aligned with no loss of mechanical stability, was prepared through the use of commercially available chloropropyl-functional silicone oil mixed into a tough commercial liquid silicone rubber silicone elastomer. The addition...... also decreased the dielectric losses of an elastomer containing dielectric permittivity-enhancing TiO2 fillers. Commercially available chloropropyl-functional silicone oil thus constitutes a facile method for improved silicone DEs, with very low dielectric losses.......Commercial viability of dielectric elastomers (DEs) is currently limited by a few obstacles, including high driving voltages (in the kV range). Driving voltage can be lowered by either decreasing the Young's modulus or increasing the dielectric permittivity of silicone elastomers, or a combination...

Multifunctional Graphene-Silicone Elastomer Nanocomposite, Method of Making the Same, and Uses Thereof

Science.gov (United States)

Pan, Shuyang (Inventor); Aksay, Ilhan A. (Inventor); Prud'Homme, Robert K. (Inventor)

2018-01-01

A nanocomposite composition having a silicone elastomer matrix having therein a filler loading of greater than 0.05 wt %, based on total nanocomposite weight, wherein the filler is functional graphene sheets (FGS) having a surface area of from 300 sq m/g to 2630 sq m2/g; and a method for producing the nanocomposite and uses thereof.

Interpenetrated polymer networks based on commercial silicone elastomers and ionic networks with high dielectric permittivity and self-healing properties

DEFF Research Database (Denmark)

Ogliani, Elisa; Yu, Liyun; Skov, Anne Ladegaard

the applicability. One method used to avoid this limitation is to increase the dielectric permittivity of the material in order to improve the actuation response at a given field. Recently, interpenetrating polymer networks (IPNs) based on covalently cross-linked commercial silicone elastomers and ionic networks...... from amino- and carboxylic acid- functional silicones have been designed[2] (Figure 1). This novel system provides both the mechanical stability and the high breakdown strength given by the silicone part of the IPNs and the high permittivity and the softening effect of the ionic network. Thus......,1 Hz), and the commercial elastomers RT625 and LR3043/30 provide thebest viscoelastic properties to the systems, since they maintain low viscous losses upon addition of ionic network. The values ofthe breakdown strength in all cases remain higher than that of the reference pure PDMS network (ranging...

Dynamic surface deformation of silicone elastomers for management of marine biofouling: laboratory and field studies using pneumatic actuation.

Science.gov (United States)

Shivapooja, Phanindhar; Wang, Qiming; Szott, Lizzy M; Orihuela, Beatriz; Rittschof, Daniel; Zhao, Xuanhe; López, Gabriel P

2015-01-01

Many strategies have been developed to improve the fouling release (FR) performance of silicone coatings. However, biofilms inevitably build on these surfaces over time. Previous studies have shown that intentional deformation of silicone elastomers can be employed to detach biofouling species. In this study, inspired by the methods used in soft-robotic systems, controlled deformation of silicone elastomers via pneumatic actuation was employed to detach adherent biofilms. Using programmed surface deformation, it was possible to release > 90% of biofilm from surfaces in both laboratory and field environments. A higher substratum strain was required to remove biofilms accumulated in the field environment as compared with laboratory-grown biofilms. Further, the study indicated that substratum modulus influences the strain needed to de-bond biofilms. Surface deformation-based approaches have potential for use in the management of biofouling in a number of technological areas, including in niche applications where pneumatic actuation of surface deformation is feasible.

Vacuum arc plasma deposition of thin titanium dioxide films on silicone elastomer as a functional coating for medical applications

Energy Technology Data Exchange (ETDEWEB)

Boudot, Cécile, E-mail: cecile.boudot@tum.de [Technical University of Munich, Department of Mechanical Engineering, Boltzmannstraße 15, D-85748 Garching bei München (Germany); Kühn, Marvin; Kühn-Kauffeldt, Marina; Schein, Jochen [Institute for Plasma Technology and Mathematics, University of Federal Armed Forces Munich, Werner-Heisenberg-Weg 39, D-85577 Neubiberg (Germany)

2017-05-01

Silicone elastomer is a promising material for medical applications and is widely used for implants with blood and tissue contact. However, its strong hydrophobicity limits adhesion of tissue cells to silicone surfaces, which can impair the healing process. To improve the biological properties of silicone, a triggerless pulsed vacuum cathodic arc plasma deposition technique was applied to deposit titanium dioxide (TiO{sub 2}) films onto the surface. Scanning electron microscopy, atomic force microscopy, X-ray photoelectron spectroscopy, Raman spectroscopy and contact angle measurements were used for coating characterization. Deposited films were about 150 nm thick and exhibited good adhesion to the underlying silicone substrate. Surface wettability and roughness both increased after deposition of the TiO{sub 2} layer. In addition, cell-biological investigations demonstrated that the in-vitro cytocompatibility of TiO{sub 2}-coated samples was greatly improved without impacting silicone's nontoxicity. For validation of use in medical devices, further investigations were conducted and demonstrated stability of surface properties in an aqueous environment for a period of 68 days and the coating's resistance to several sterilization methods. - Highlights: • Vacuum arc plasma was applied to deposit titanium dioxide films onto silicone. • Thickness, roughness and composition of the films were determined. • Cytocompatibility of coated silicone elastomer is greatly improved. • Films have good adhesion to the substrate and are stable, non-toxic and sterilizable.

Stronger multilayer acrylic dielectric elastomer actuators with silicone gel coatings

Science.gov (United States)

Lau, Gih-Keong; La, Thanh-Giang; Sheng-Wei Foong, Ervin; Shrestha, Milan

2016-12-01

Multilayer dielectric elastomer actuators (DEA) perform worst off than single-layer DEAs due to higher susceptibility to electro-thermal breakdown. This paper presents a hot-spot model to predict the electro-thermal breakdown field of DEAs and its dependence on thermal insulation. To inhibit the electrothermal breakdown, silicone gel coating was applied as barrier coating to multilayer acrylic DEA. The gel coating helps suppress the electro-thermally induced puncturing of DEA membrane at the hot spot. As a result, the gel-coated DEAs, in either a single layer or a multilayer stack, can produce 30% more isometric stress change as compared to those none-coated. These gel-coated acrylic DEAs show great potential to make stronger artificial muscles.

The Current State of Silicone-Based Dielectric Elastomer Transducers

DEFF Research Database (Denmark)

Madsen, Frederikke Bahrt; Daugaard, Anders Egede; Hvilsted, Søren

2016-01-01

class of transducer due to their inherent lightweight and potentially large strains. For the field to progress towards industrial implementation, a leap in material devel- opment is required, specifically targeting longer lifetime and higher energy densities to provide more efficient transduction at lower...... driving voltages. In this review, the current state of sili- cone elastomers for DETs is summarised and critically discussed, including commercial elastomers, composites, polymer blends, grafted elastomers and complex network structures. For future developments in the field it is essential that all aspects...

High breakdown-strength composites from liquid silicone rubbers

DEFF Research Database (Denmark)

Vudayagiri, Sindhu; Zakaria, Shamsul Bin; Yu, Liyun

2014-01-01

In this paper we investigate the performance of liquid silicone rubbers (LSRs) as dielectric elastomer transducers. Commonly used silicones in this application include room-temperature vulcanisable (RTV) silicone elastomers and composites thereof. Pure LSRs and their composites with commercially...

Composite magnetorheological elastomers as dielectrics for plane capacitors: Effects of magnetic field intensity

Directory of Open Access Journals (Sweden)

Maria Balasoiu

Full Text Available The fabrication of composite magnetorheological elastomers (MRECs based on silicone rubber, carbonyl iron microparticles (10% vol. and polyurethane elastomer doped with 0%, 10% and 20% volume concentration TiO2 microparticles is presented. The obtained MRECs have the shape of thin foils and are used as dielectric materials for manufacturing plane capacitors. Using the plane capacitor method and expression of capacitance as a function of magnetic field intensity, combined with linear elasticity theory, the static magnetoelastic model of the composite is obtained and analyzed. Keywords: Magnetorheological elastomer, TiO2 microparticles, Silicone rubber, Carbonyl iron, Plane capacitor, Magnetoelasticity

Thermal tuning of a silicon photonic crystal cavity infilled with an elastomer

NARCIS (Netherlands)

Erdamar, A.K.; Van Leest, M.M.; Picken, S.J.; Caro, J.

2011-01-01

Thermal tuning of the transmission of an elastomer infilled photonic crystal cavity is studied. An elastomer has a thermal expansion-induced negative thermo-optic coefficient that leads to a strong decrease of the refractive index upon heating. This property makes elastomer highly suitable for

Packing polymorphism of dapivirine and its impact on the performance of a dapivirine-releasing silicone elastomer vaginal ring

OpenAIRE

McCoy, Clare F.; Murphy, Diarmaid J.; Boyd, Peter; Derrick, Tiffany; Spence, Patrick; Devlin, Brid; Malcolm, Robert

2017-01-01

A silicone elastomer vaginal ring providing sustained release over 28 days of the antiretroviral microbicide dapivirine has recently completed Phase III clinical testing and showed moderate protection against HIV acquisition. In support of the product licensure program, we report the impact of dapivirine packing polymorphism on the thermal and solubility characteristics of dapivirine and on the in vitro performance of the 25 mg dapivirine ring product. This is the first time that polymorphism...

Biodegradable elastomers and silicon nanomembranes/nanoribbons for stretchable, transient electronics, and biosensors.

Science.gov (United States)

Hwang, Suk-Won; Lee, Chi Hwan; Cheng, Huanyu; Jeong, Jae-Woong; Kang, Seung-Kyun; Kim, Jae-Hwan; Shin, Jiho; Yang, Jian; Liu, Zhuangjian; Ameer, Guillermo A; Huang, Yonggang; Rogers, John A

2015-05-13

Transient electronics represents an emerging class of technology that exploits materials and/or device constructs that are capable of physically disappearing or disintegrating in a controlled manner at programmed rates or times. Inorganic semiconductor nanomaterials such as silicon nanomembranes/nanoribbons provide attractive choices for active elements in transistors, diodes and other essential components of overall systems that dissolve completely by hydrolysis in biofluids or groundwater. We describe here materials, mechanics, and design layouts to achieve this type of technology in stretchable configurations with biodegradable elastomers for substrate/encapsulation layers. Experimental and theoretical results illuminate the mechanical properties under large strain deformation. Circuit characterization of complementary metal-oxide-semiconductor inverters and individual transistors under various levels of applied loads validates the design strategies. Examples of biosensors demonstrate possibilities for stretchable, transient devices in biomedical applications.

Packing Polymorphism of Dapivirine and Its Impact on the Performance of a Dapivirine-Releasing Silicone Elastomer Vaginal Ring.

Science.gov (United States)

McCoy, Clare F; Murphy, Diarmaid J; Boyd, Peter; Derrick, Tiffany; Spence, Patrick; Devlin, Brid; Malcolm, R Karl

2017-08-01

A silicone elastomer vaginal ring providing sustained release over 28 days of the anti-retroviral microbicide dapivirine has recently completed phase III clinical testing and showed moderate protection against HIV acquisition. In support of the product licensure program, we report the impact of dapivirine packing polymorphism on the thermal and solubility characteristics of dapivirine and on the in vitro performance of the 25 mg dapivirine ring product. This is the first time that polymorphism has been reported for a drug-releasing vaginal ring product. Thermal, particle size, powder X-ray diffraction, and thermodynamic solubility analyses of dapivirine polymorphic forms I and IV, both of which are persistent at room temperature and with form I being the thermodynamically stable form, were conducted for both micronized and non-micronized materials. No significant differences in solubility between DPV forms I and IV were observed in media commonly used for in vitro release testing. Matrix-type silicone elastomer vaginal rings were manufactured and the impact of dapivirine polymorphism on key in vitro parameters (compression and tensile behavior; content assay; in vitro release; residual content assay) was investigated. The data demonstrate that dapivirine packing polymorphism has no significant impact on in vitro performance of the 25 mg dapivirine vaginal ring. Copyright © 2017 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Glycerol as high-permittivity liquid filler in dielectric silicone elastomers

DEFF Research Database (Denmark)

Mazurek, Piotr Stanislaw; Yu, Liyun; Gerhard, R.

2016-01-01

A recently reported novel class of elastomers was tested with respect to its dielectric properties. The new elastomer materialis based on a commercially available poly(dimethylsiloxane) composition, which has been modified by embedding glycerol droplets intoits matrix. The approach has two major ......, and the applicability ofthe models is discussed. VC 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016, 133, 44153....

Electrical breakdown phenomena of dielectric elastomers

DEFF Research Database (Denmark)

Yu, Liyun; Mateiu, Ramona Valentina; Skov, Anne Ladegaard

2017-01-01

years. However, optimization with respect to the dielectric permittivity solely may lead to other problematic phenomena such as premature electrical breakdown. In this work, we focus on the chloro propyl functionalized silicone elastomers prepared in Madsen et al[2] and we investigate the electrical...

Effects of Atomic Oxygen and Grease on Outgassing and Adhesion of Silicone Elastomers for Space Applications

Science.gov (United States)

de Groh, Henry C.; Puleo, Bernadette J.; Steinetz, Bruce M.

An investigation of silicone elastomers for seals used in docking and habitat systems for future space exploration vehicles is being conducted at NASA. For certain missions, NASA is considering androgynous docking systems where two vehicles each having a seal would be required to: dock for a period of time, seal effectively, and then separate with minimum push-off forces for undocking. Silicone materials are generally chosen for their wide operating temperatures and low leakage rates. However silicone materials are often sticky and usually exhibit considerable adhesion when mated against metals and silicone surfaces. This paper investigates the adhesion unit pressure for a space rated silicone material (S0383-70) for either seal-on-seal (SoS) or seal-on-aluminum (SoAl) operation modes in the following conditions: as-received, after ground-based atomic-oxygen (AO) pre-treatment, after application of a thin coating of a space-qualified grease (Braycote 601EF), and after a combination of AO pre-treatment and grease coating. In order of descending adhesion reduction, the AO treatment reduced seal adhesion the most, followed by the AO plus grease pre-treatment, followed by the grease treatment. The effects of various treatments on silicone (S0383-70 and ELA-SA-401) outgassing properties were also investigated. The leading adhesion AO pre-treatment reduction led to a slight decrease in outgassing for the S0383-70 material and virtually no change in ELA-SA-401 outgassing.

Liquid-Embedded Elastomer Electronics

Science.gov (United States)

Kramer, Rebecca; Majidi, Carmel; Park, Yong-Lae; Paik, Jamie; Wood, Robert

2012-02-01

Hyperelastic sensors are fabricated by embedding a silicone rubber film with microchannels of conductive liquid. In the case of soft tactile sensors, pressing the surface of the elastomer will deform the cross-section of underlying channels and change their electrical resistance. Soft pressure sensors may be employed in a variety of applications. For example, a network of pressure sensors can serve as artificial skin by yielding detailed information about contact pressures. This concept was demonstrated in a hyperelastic keypad, where perpendicular conductive channels form a quasi-planar network within an elastomeric matrix that registers the location, intensity and duration of applied pressure. In a second demonstration, soft curvature sensors were used for joint angle proprioception. Because the sensors are soft and stretchable, they conform to the host without interfering with the natural mechanics of motion. This marked the first use of liquid-embedded elastomer electronics to monitor human or robotic motion. Finally, liquid-embedded elastomers may be implemented as conductors in applications that call for flexible or stretchable circuitry, such as robotic origami.

Full-scale demonstration. Fire testing of a system for penetration sealing based on foamed silicone elastomer: Studsvik 77-05-26

International Nuclear Information System (INIS)

Brown, A.

1978-06-01

Testing of a system for making fire retardant penetration seals based on foamed-in-place silicone elastomer is described. The report covers - Concept of fire retardant penetration seals and the Chemtrol system, Design FC 225 - Account of materials used to prepare seals and method of application - Test assembly and full-scale facility at Studsvik - Classification of seals used in demonstration - Diagrams of seals and photographs taken after demonstration

Full-scale demonstration. Fire testing of a system for penetration sealing based on foamed silicone elastomer: Studsvik 77-05-26

International Nuclear Information System (INIS)

Brown, A.

1978-06-01

Testing of a system for making fire retardant penetration seals based on foamed-in-place silicone elastomer is described. The report covers - Concept of fire retardant penetration seals and the Chemtrol system, Design FC 225 - Account of materials used to prepare seals and method of application - Test assembly and full-scale facility at Studsvik - Classification of seals used in demonstration - Diagrams of seals and photographs taken after demonstration (author)

ZnO as a cheap and effective filler for high breakdown strength elastomers

DEFF Research Database (Denmark)

Yu, Liyun; Skov, Anne Ladegaard

2017-01-01

. In this article, we explore the use of a cheap and abundant metal oxide filler, namely ZnO, as a filler in silicone-based dielectric elastomers. The electro-mechanical properties of the elastomer composites are investigated, and their performance is evaluated by means of figures of merit. Various commercial...

Centrifugal forming and mechanical properties of silicone-based elastomers for soft robotic actuators

Science.gov (United States)

Kulkarni, Parth

This thesis describes the centrifugal forming and resulting mechanical properties of silicone-based elastomers for the manufacture of soft robotic actuators. This process is effective at removing bubbles that get entrapped within 3D-printed, enclosed molds. Conventional methods for rapid prototyping of soft robotic actuators to remove entrapped bubbles typically involve degassing under vacuum, with open-faced molds that limit the layout of formed parts to raised 2D geometries. As the functionality and complexity of soft robots increase, there is a need to mold complete 3D structures with controlled thicknesses or curvatures on multiples surfaces. In addition, characterization of the mechanical properties of common elastomers for these soft robots has lagged the development of new designs. As such, relationships between resulting material properties and processing parameters are virtually non-existent. One of the goals of this thesis is to provide guidelines and physical insights to relate the design, processing conditions, and resulting properties of soft robotic components to each other. Centrifugal forming with accelerations on the order of 100 g's is capable of forming bubble-free, true 3D components for soft robotic actuators, and resulting demonstrations in this work include an aquatic locomotor, soft gripper, and an actuator that straightens when pressurized. Finally, this work shows that the measured mechanical properties of 3D geometries fabricated within enclosed molds through centrifugal forming possess comparable mechanical properties to vacuumed materials formed from open-faced molds with raised 2D features.

Zipping dielectric elastomer actuators: characterization, design and modeling

International Nuclear Information System (INIS)

Maffli, L; Rosset, S; Shea, H R

2013-01-01

We report on miniature dielectric elastomer actuators (DEAs) operating in zipping mode with an analytical model that predicts their behavior. Electrostatic zipping is a well-known mechanism in silicon MEMS to obtain large deformations and forces at lower voltages than for parallel plate electrostatic actuation. We extend this concept to DEAs, which allows us to obtain much larger out-of-plane displacements compared to silicon thanks to the softness of the elastomer membrane. We study experimentally the effect of sidewall angles and elastomer prestretch on 2.3 mm diameter actuators with PDMS membranes. With 15° and 22.5° sidewall angles, the devices zip in a bistable manner down 300 μm to the bottom of the chambers. The highly tunable bistable behavior is controllable by both chamber geometry and membrane parameters. Other specific characteristics of zipping DEAs include well-controlled deflected shape, tunable displacement versus voltage characteristics to virtually any shape, including multi-stable modes, sealing of embedded holes or channels for valving action and the reduction of the operating voltage. These properties make zipping DEAs an excellent candidate for applications such as integrated microfluidics actuators or Braille displays. (paper)

Vacuum arc plasma deposition of thin titanium dioxide films on silicone elastomer as a functional coating for medical applications.

Science.gov (United States)

Boudot, Cécile; Kühn, Marvin; Kühn-Kauffeldt, Marina; Schein, Jochen

2017-05-01

Silicone elastomer is a promising material for medical applications and is widely used for implants with blood and tissue contact. However, its strong hydrophobicity limits adhesion of tissue cells to silicone surfaces, which can impair the healing process. To improve the biological properties of silicone, a triggerless pulsed vacuum cathodic arc plasma deposition technique was applied to deposit titanium dioxide (TiO 2 ) films onto the surface. Scanning electron microscopy, atomic force microscopy, X-ray photoelectron spectroscopy, Raman spectroscopy and contact angle measurements were used for coating characterization. Deposited films were about 150nm thick and exhibited good adhesion to the underlying silicone substrate. Surface wettability and roughness both increased after deposition of the TiO 2 layer. In addition, cell-biological investigations demonstrated that the in-vitro cytocompatibility of TiO 2 -coated samples was greatly improved without impacting silicone's nontoxicity. For validation of use in medical devices, further investigations were conducted and demonstrated stability of surface properties in an aqueous environment for a period of 68days and the coating's resistance to several sterilization methods. Copyright © 2016 Elsevier B.V. All rights reserved.

Effect of manufacturing and experimental conditions on the mechanical and surface properties of silicone elastomer scaffolds used in endothelial mechanobiological studies.

Science.gov (United States)

Campeau, Marc-Antoine; Lortie, Audrey; Tremblay, Pierrick; Béliveau, Marc-Olivier; Dubé, Dominic; Langelier, Ève; Rouleau, Léonie

2017-07-14

Mechanobiological studies allow the characterization of cell response to mechanical stresses. Cells need to be supported by a material with properties similar to the physiological environment. Silicone elastomers have been used to produce various in vitro scaffolds of different geometries for endothelial cell studies given its relevant mechanical, optical and surface properties. However, obtaining defined and repeatable properties is a challenge as depending on the different manufacturing and processing steps, mechanical and surface properties may vary significantly between research groups. The impact of different manufacturing and processing methods on the mechanical and surface properties was assessed by measuring the Young's modulus and the contact angle. Silicone samples were produced using different curing temperatures and processed with different sterilization techniques and hydrophilization conditions. Different curing temperatures were used to obtain materials of different stiffness with a chosen silicone elastomer, i.e. Sylgard 184 ® . Sterilization by boiling had a tendency to stiffen samples cured at lower temperatures whereas UV and ethanol did not alter the material properties. Hydrophilization using sulphuric acid allowed to decrease surface hydrophobicity, however this effect was lost over time as hydrophobic recovery occurred. Extended contact with water maintained decreased hydrophobicity up to 7 days. Mechanobiological studies require complete cell coverage of the scaffolds used prior to mechanical stresses exposure. Different concentrations of fibronectin and collagen were used to coat the scaffolds and cell seeding density was varied to optimize cell coverage. This study highlights the potential bias introduced by manufacturing and processing conditions needed in the preparation of scaffolds used in mechanobiological studies involving endothelial cells. As manufacturing, processing and cell culture conditions are known to influence cell

Techniques for hot embossing microstructures on liquid silicone rubbers with fillers

DEFF Research Database (Denmark)

Vudayagiri, Sindhu; Yu, Liyun; Skov, Anne Ladegaard

2015-01-01

Embossing is an established process for the thermoplastic elastomers but not yet for the thermosetting elastomers. It has already been shown that hot embossing is a viable technology for imprinting microstructures in addition to curing thin silicone films at their gel point. It is one of the simp......Embossing is an established process for the thermoplastic elastomers but not yet for the thermosetting elastomers. It has already been shown that hot embossing is a viable technology for imprinting microstructures in addition to curing thin silicone films at their gel point. It is one...

Maxillofacial imaging

Energy Technology Data Exchange (ETDEWEB)

Larheim, T.A. [Oslo Univ. (Norway). Dept. of Maxillofacial Radiology; Westesson, P.L. [Univ. of Rochester School of Medicine and Dentistry, NY (United States). Div. of Diagnostic and Interventional Radiology

2006-07-01

Maxillofacial imaging has evolved dramatically over the past two decades with development of new cross-sectional imaging techniques. Traditional maxillofacial imaging was based on plain films and dental imaging. However, today's advanced imaging techniques with CT and MRI have only been partially implemented for maxillofacial questions. This book bridges the gap between traditional maxillofacial imaging and advanced medical imaging. We have applied CT and MRI to a variety of maxillofacial cases and these are illustrated with high-quality images and multiple planes. A comprehensive chapter on imaging anatomy is also included. This book is useful for oral and maxillofacial radiologists, oral and maxillofacial surgeons, dentists, radiologists, plastic surgeons, head and neck surgeons, and others that work with severe maxillofacial disorders. (orig.)

Dielectric silicone elastomers with mixed ceramic nanoparticles

International Nuclear Information System (INIS)

Stiubianu, George; Bele, Adrian; Cazacu, Maria; Racles, Carmen; Vlad, Stelian; Ignat, Mircea

2015-01-01

Highlights: • Composite ceramics nanoparticles (MCN) with zirconium dioxide and lead zirconate. • Dielectric elastomer films wDith PDMS matrix and MCN as dielectric filler. • Hydrophobic character—water resistant and good flexibility specific to siloxanes. • Increased value of dielectric constant with the content of MCN in dielectric films. • Increased energy output from uniaxial deformation of the dielectric elastomer films. - Abstract: A ceramic material consisting in a zirconium dioxide-lead zirconate mixture has been obtained by precipitation method, its composition being proved by wide angle X-ray powder diffraction and energy-dispersive X-ray spectroscopy. The average diameter of the ceramic particles ranged between 50 and 100 nm, as revealed by transmission electron microscopy images. These were surface treated and used as filler for a high molecular mass polydimethylsiloxane-α,ω-diol (Mn = 450,000) prepared in laboratory, the resulted composites being further processed as films and crosslinked. A condensation procedure, unusual for polydimethylsiloxane having such high molecular mass, with a trifunctional silane was approached for the crosslinking. The effect of filler content on electrical and mechanical properties of the resulted materials was studied and it was found that the dielectric permittivity of nanocomposites increased in line with the concentration of ceramic nanoparticles

Dielectric silicone elastomers with mixed ceramic nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Stiubianu, George, E-mail: george.stiubianu@icmpp.ro [“Petru Poni” Institute of Macromolecular Chemistry, Aleea Gr. Ghica Voda 41A, Iasi 700487 (Romania); Bele, Adrian; Cazacu, Maria; Racles, Carmen; Vlad, Stelian [“Petru Poni” Institute of Macromolecular Chemistry, Aleea Gr. Ghica Voda 41A, Iasi 700487 (Romania); Ignat, Mircea [National R& D Institute for Electrical Engineering ICPE-CA Bucharest, Splaiul Unirii 313, District 3, Bucharest 030138 (Romania)

2015-11-15

Highlights: • Composite ceramics nanoparticles (MCN) with zirconium dioxide and lead zirconate. • Dielectric elastomer films wDith PDMS matrix and MCN as dielectric filler. • Hydrophobic character—water resistant and good flexibility specific to siloxanes. • Increased value of dielectric constant with the content of MCN in dielectric films. • Increased energy output from uniaxial deformation of the dielectric elastomer films. - Abstract: A ceramic material consisting in a zirconium dioxide-lead zirconate mixture has been obtained by precipitation method, its composition being proved by wide angle X-ray powder diffraction and energy-dispersive X-ray spectroscopy. The average diameter of the ceramic particles ranged between 50 and 100 nm, as revealed by transmission electron microscopy images. These were surface treated and used as filler for a high molecular mass polydimethylsiloxane-α,ω-diol (Mn = 450,000) prepared in laboratory, the resulted composites being further processed as films and crosslinked. A condensation procedure, unusual for polydimethylsiloxane having such high molecular mass, with a trifunctional silane was approached for the crosslinking. The effect of filler content on electrical and mechanical properties of the resulted materials was studied and it was found that the dielectric permittivity of nanocomposites increased in line with the concentration of ceramic nanoparticles.

Comparison of conventional and plant-extract disinfectant solutions on the hardness and color stability of a maxillofacial elastomer after artificial aging.

Science.gov (United States)

Guiotti, Aimée Maria; Goiato, Marcelo Coelho; Dos Santos, Daniela Micheline; Vechiato-Filho, Aljomar José; Cunha, Bruno Guandalini; Paulini, Marcela Borghi; Moreno, Amália; de Almeida, Margarete Teresa Gottardo

2016-04-01

Silicone elastomers undergo physical and chemical degradation with disinfecting solutions. Phytotherapy may be a suitable solution for disinfection. However, its effect on the properties of the silicone material is unknown. The purpose of this in vitro study was to evaluate the effect of disinfection with conventional and plant-extract solutions and of artificial aging on the hardness and color stability of a facial silicone associated with pigments and an opacifier. Four hundred specimens of silicone (MDX4-4210) were fabricated (5×6 mm). Two pigment shades and 1 dry opacifier were combined in the tested material, and 4 groups (n=10) were obtained: colorless (GI), colorless with opacifier (GII), medium pigment with opacifier (GIII), and black pigment with opacifier (GIV). Specimens were subjected to disinfection (30 days) using saline solution, water, and neutral soap (digital friction, 30 seconds), chlorhexidine 4%, Hydrastis canadensis, and Cymbopogon nardus extracts (immersion, 10 minutes). Shore A hardness (ASTM D2240) and color analyses were performed before and after disinfection. Specimens were then exposed to 1008 hours of artificial aging (ASTM 53) and subjected to final hardness and color readings. The results were analyzed with ANOVA and the Tukey significant difference test (α=.05). The opacifier increased the hardness (GII). For GII, the H. canadensis solution and the friction with water and soap promoted significantly reduced hardness; the friction also promoted a reduction in this property for GIV. The GIII was not affected after disinfection. A significant difference was found between the ΔE values of the specimens disinfected with H. canadensis, C. nardus, and chlorhexidine, and specimens subjected to saline solution and neutral soap. The hardness of MDX4-4210 after the experimental procedure was considered clinically acceptable for facial prostheses. All groups showed clinically unacceptable color alterations regardless of the disinfecting

Dielectric elastomers with novel highly-conducting electrodes

Science.gov (United States)

Böse, Holger; Uhl, Detlev

2013-04-01

Beside the characteristics of the elastomer material itself, the performance of dielectric elastomers in actuator, sensor as well as generator applications depends also on the properties of the electrode material. Various electrode materials based on metallic particles dispersed in a silicone matrix were manufactured and investigated. Anisotropic particles such as silver-coated copper flakes and silver-coated glass flakes were used for the preparation of the electrodes. The concentration of the metallic particles and the thickness of the electrode layers were varied. Specific conductivities derived from resistance measurements reached about 100 S/cm and surmount those of the reference materials based on graphite and carbon black by up to three orders of magnitude. The high conductivities of the new electrode materials can be maintained even at very large stretch deformations up to 200 %.

Silicone elastomers with covalently incorporated aromatic voltage stabilisers

DEFF Research Database (Denmark)

A Razak, Aliff Hisyam; Skov, Anne Ladegaard

2017-01-01

to the incorporationof an aromatic voltage stabiliser, were prepared by cross-linking synthesised polydimethylsiloxane–polyphenylmethylsiloxane (PDMS–PPMS) copolymers. PPMS possesses voltage stabilisation capabilitiesbut is immiscible in PDMS, and thus the copolymerisation of the two components was necessary...... forhomogeneity. Concentrations of the voltage stabiliser were varied by changing the molecular weights ofthe PPMS in the copolymer. The developed elastomers were inherently soft with enhanced electricalbreakdown strengths, due to delocalisedp-electrons of the aromatic constituent. An optimumconcentration...

Leak Rate Performance of Silicone Elastomer O-Rings Contaminated with JSC-1A Lunar Regolith Simulant

Science.gov (United States)

Oravec, Heather Ann; Daniels, Christopher C.

2014-01-01

Contamination of spacecraft components with planetary and foreign object debris is a growing concern. Face seals separating the spacecraft cabin from the debris filled environment are particularly susceptible; if the seal becomes contaminated there is potential for decreased performance, mission failure, or catastrophe. In this study, silicone elastomer O-rings were contaminated with JSC- 1A lunar regolith and their leak rate performance was evaluated. The leak rate values of contaminated O-rings at four levels of seal compression were compared to those of as-received, uncontaminated, O-rings. The results showed a drastic increase in leak rate after contamination. JSC-1A contaminated O-rings lead to immeasurably high leak rate values for all levels of compression except complete closure. Additionally, a mechanical method of simulant removal was examined. In general, this method returned the leak rate to as-received values.

High-cycle electromechanical aging of dielectric elastomer actuators with carbon-based electrodes

Science.gov (United States)

de Saint-Aubin, C. A.; Rosset, S.; Schlatter, S.; Shea, H.

2018-07-01

We present high-cycle aging tests of dielectric elastomer actuators (DEAs) based on silicone elastomers, reporting on the time-evolution of actuation strain and of electrode resistance over millions of cycles. We compare several types of carbon-based electrodes, and for the first time show how the choice of electrode has a dramatic influence on DEA aging. An expanding circle DEA configuration is used, consisting of a commercial silicone membrane with the following electrodes: commercial carbon grease applied manually, solvent-diluted carbon grease applied by stamping (pad printing), loose carbon black powder applied manually, carbon black powder suspension applied by inkjet-printing, and conductive silicone-carbon composite applied by stamping. The silicone-based DEAs with manually applied carbon grease electrodes show the shortest lifetime of less than 105 cycles at 5% strain, while the inkjet-printed carbon powder and the stamped silicone-carbon composite make for the most reliable devices, with lifetimes greater than 107 cycles at 5% strain. These results are valid for the specific dielectric and electrode configurations that were tested: using other dielectrics or electrode formulations would lead to different lifetimes and failure modes. We find that aging (as seen in the change in resistance and in actuation strain versus cycle number) is independent of the actuation frequency from 10 Hz to 200 Hz, and depends on the total accumulated time the DEA spends in an actuated state.

Glycerol as high-permittivity liquid filler in dielectric silicone elastomers

DEFF Research Database (Denmark)

Mazurek, Piotr Stanislaw; Yu, Liyun; Skov, Anne Ladegaard

of the composite. In combination with very low cost and easy preparation, the two property enhancements lead to a very attractive dielectric elastomer material. Experimental permittivity data are compared to various theoretical models that predict relative-permittivity changes as a function of filler loading...

The Future of Swelling Elastomers: An Elastomer Manufacturer's View of Swelling Elastomer Developments and Market Trends

Directory of Open Access Journals (Sweden)

R Seyger

2013-06-01

Full Text Available Swelling elastomers have gained acceptance as very effective products for creating sealing in various industries, including those creating energy from fossil fuels and geothermal resources. This paper outlines the research and development work being conducted not only in the application of these elastomers but also in the development work required to create new generations of elastomers. It touches on fundamental research into the mechanics of swelling with the intent to create a better and more predictable sealing as well as more advanced elastomers. It lifts the veil on the direction of work being done on new elastomers being developed in order to enable a better control of swelling. By doing so, the research is opening up field of applications for new equipment designs and mechanical possibilities in the future. Additionally, it addresses the need for a better and more in-depth dialogue between both chemical and mechanical engineers, and the elastomer companies and their customers on the potential that both swelling and non-swelling elastomers can offer to the industry as a whole.

Polysiloxane-based luminescent elastomers prepared by thiol-ene "click" chemistry.

Science.gov (United States)

Zuo, Yujing; Lu, Haifeng; Xue, Lei; Wang, Xianming; Wu, Lianfeng; Feng, Shengyu

2014-09-26

Side-chain vinyl poly(dimethylsiloxane) has been modified with mercaptopropionic acid, methyl 3-mercaptopropionate, and mercaptosuccinic acid. Coordinative bonding of Eu(III) to the functionalized polysiloxanes was then carried out and crosslinked silicone elastomers were prepared by thiol-ene curing reactions of these composites. All these europium complexes could be cast to form transparent, uniform, thin elastomers with good flexibility and thermal stability. The networks were characterized by FTIR, NMR, UV/Vis, and luminescence spectroscopy as well as by scanning electron microscopy, thermogravimetric analysis, and X-ray photoelectron spectroscopy. The europium elastomer luminophores exhibited intense red light at 617 nm under UV excitation at room temperature due to the (5)D0 →(7)F2 transition in Eu(III) ions. The newly synthesized luminescent materials offer many advantages, including the desired mechanical flexibility. They cannot be dissolved or fused, and so they have potential for use in optical and electronic applications. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Safety of a silicone elastomer vaginal ring as potential microbicide delivery method in African women: A Phase 1 randomized trial.

Science.gov (United States)

Nel, Annaléne; Martins, Janine; Bekker, Linda-Gail; Ramjee, Gita; Masenga, Gileard; Rees, Helen; van Niekerk, Neliëtte

2018-01-01

Women in sub-Saharan Africa are in urgent need of female-initiated human immunodeficiency virus (HIV) preventative methods. Vaginal rings are one dosage form in development for delivery of HIV microbicides. However, African women have limited experience with vaginal rings. This Phase I, randomized, crossover trial assessed and compared the safety, acceptability and adherence of a silicone elastomer placebo vaginal ring, intended as a microbicide delivery method, inserted for a 12-week period in healthy, HIV-negative, sexually active women in South Africa and Tanzania. 170 women, aged 18 to 35 years were enrolled with 88 women randomized to Group A, using a placebo vaginal ring for 12 weeks followed by a 12-week safety observation period. 82 women were randomized to Group B and observed for safety first, followed by a placebo vaginal ring for 12 weeks. Safety was assessed by clinical laboratory assessments, pelvic/colposcopy examinations and adverse events. Possible carry-over effect was addressed by ensuring no signs or symptoms of genital irritation at crossover. No safety concerns were identified for any safety variables assessed during the trial. No serious adverse events were reported considered related to the placebo vaginal ring. Vaginal candidiasis was the most common adverse event occurring in 11% of participants during each trial period. Vaginal discharge (2%), vaginal odour (2%), and bacterial vaginitis (2%) were assessed as possibly or probably related to the vaginal ring. Thirty-four percent of participants had sexually transmitted infections (STIs) at screening, compared to 12% of participants who tested positive for STIs at crossover and the final trial visit. Three participants (2%) tested HIV positive during the trial. The silicone elastomer vaginal ring had no safety concerns, demonstrating a profile favorable for further development for topical release of antiretroviral-based microbicides.

Applications of pressure-sensitive dielectric elastomer sensors

Science.gov (United States)

Böse, Holger; Ocak, Deniz; Ehrlich, Johannes

2016-04-01

Dielectric elastomer sensors for the measurement of compression loads with high sensitivity are described. The basic design of the sensors exhibits two profiled surfaces between which an elastomer film is confined. All components of the sensor were prepared with silicone whose stiffness can be varied in a wide range. Depending on details of the sensor design, various effects contribute to the enhancement of the capacitance. The intermediate elastomer film is stretched upon compression and electrode layers on the elastomer profiles and in the elastomer film approach each other. Different designs of the pressure sensor give rise to very different sensor characteristics in terms of the dependence of electric capacitance on compression force. Due to their inherent flexibility, the pressure sensors can be used on compliant substrates such as seats or beds or on the human body. This gives rise to numerous possible applications. The contribution describes also some examples of possible sensor applications. A glove was equipped with various sensors positioned at the finger tips. When grabbing an object with the glove, the sensors can detect the gripping forces of the individual fingers with high sensitivity. In a demonstrator of the glove equipped with seven sensors, the capacitances representing the gripping forces are recorded on a display. In another application example, a lower limb prosthesis was equipped with a pressure sensor to detect the load on the remaining part of the leg and the load is displayed in terms of the measured capacitance. The benefit of such sensors is to detect an eventual overload in order to prevent possible pressure sores. A third example introduces a seat load sensor system based on four extended pressure sensor mats. The sensor system detects the load distribution of a person on the seat. The examples emphasize the high performance of the new pressure sensor technology.

Soft silicone based interpenetrating networks as materials for actuators

DEFF Research Database (Denmark)

Yu, Liyun; Gonzalez, Lidia; Hvilsted, Søren

2014-01-01

A new approach based on silicone interpenetrating networks with orthogonal chemistries has been investigated with focus on developing soft and flexible elastomers with high energy densities and small viscous losses. The interpenetrating networks are made as simple two pot mixtures...... as for the commercial available silylation based elastomers such as Elastosil RT625. The resulting interpenetrating networks are formulated to be softer than RT625 to increase the actuation caused when applying a voltage due to their softness combined with the significantly higher permittivity than the pure silicone...

Stress measurements of planar dielectric elastomer actuators

Energy Technology Data Exchange (ETDEWEB)

Osmani, Bekim; Aeby, Elise A.; Müller, Bert [Biomaterials Science Center, University of Basel, Gewerbestrasse 14, 4123 Allschwil (Switzerland)

2016-05-15

Dielectric elastomer actuator (DEA) micro- and nano-structures are referred to artificial muscles because of their specific continuous power and adequate time response. The bending measurement of an asymmetric, planar DEA is described. The asymmetric cantilevers consist of 1 or 5 μm-thin DEAs deposited on polyethylene naphthalate (PEN) substrates 16, 25, 38, or 50 μm thick. The application of a voltage to the DEA electrodes generates an electrostatic pressure in the sandwiched silicone elastomer layer, which causes the underlying PEN substrate to bend. Optical beam deflection enables the detection of the bending angle vs. applied voltage. Bending radii as large as 850 m were reproducibly detected. DEA tests with electric fields of up to 80 V/μm showed limitations in electrode’s conductivity and structure failures. The actuation measurement is essential for the quantitative characterization of nanometer-thin, low-voltage, single- and multi-layer DEAs, as foreseen for artificial sphincters to efficiently treat severe urinary and fecal incontinence.

Stress measurements of planar dielectric elastomer actuators

International Nuclear Information System (INIS)

Osmani, Bekim; Aeby, Elise A.; Müller, Bert

2016-01-01

Dielectric elastomer actuator (DEA) micro- and nano-structures are referred to artificial muscles because of their specific continuous power and adequate time response. The bending measurement of an asymmetric, planar DEA is described. The asymmetric cantilevers consist of 1 or 5 μm-thin DEAs deposited on polyethylene naphthalate (PEN) substrates 16, 25, 38, or 50 μm thick. The application of a voltage to the DEA electrodes generates an electrostatic pressure in the sandwiched silicone elastomer layer, which causes the underlying PEN substrate to bend. Optical beam deflection enables the detection of the bending angle vs. applied voltage. Bending radii as large as 850 m were reproducibly detected. DEA tests with electric fields of up to 80 V/μm showed limitations in electrode’s conductivity and structure failures. The actuation measurement is essential for the quantitative characterization of nanometer-thin, low-voltage, single- and multi-layer DEAs, as foreseen for artificial sphincters to efficiently treat severe urinary and fecal incontinence.

Preparation and Characterizing of PANI/PDMS Elastomer for Artificial Muscles

Science.gov (United States)

Zhang, Yiyang; Zhang, Jie; Wang, Genlin; Zhang, Ming; Luo, Zhiwei

2018-01-01

A dielectric elastomer has been synthesized using organic soluble PANI and PDMS through solution blending method for applications as artificial muscles. The dielectric constant of PANI/PDMS composite reached 4.82 with a filling amount of 0.8 wt.%, which was 2.24 times of pure silicone, due to the dipole polarization in matrix network and electron polarization in conductive polyaniline. The actuated strain of 0.8w.t % PANI/PDMS was 16.57% compared to 8.52% of pure silicone at an electric field of 10V/μm, and can be applied as a soft actuator.

3D Printed Surgical Simulation Models as educational tool by maxillofacial surgeons.

Science.gov (United States)

Werz, S M; Zeichner, S J; Berg, B-I; Zeilhofer, H-F; Thieringer, F

2018-02-26

The aim of this study was to evaluate whether inexpensive 3D models can be suitable to train surgical skills to dental students or oral and maxillofacial surgery residents. Furthermore, we wanted to know which of the most common filament materials, acrylonitrile butadiene styrene (ABS) or polylactic acid (PLA), can better simulate human bone according to surgeons' subjective perceptions. Upper and lower jaw models were produced with common 3D desktop printers, ABS and PLA filament and silicon rubber for soft tissue simulation. Those models were given to 10 blinded, experienced maxillofacial surgeons to perform sinus lift and wisdom teeth extraction. Evaluation was made using a questionnaire. Because of slightly different density and filament prices, each silicon-covered model costs between 1.40-1.60 USD (ABS) and 1.80-2.00 USD (PLA) based on 2017 material costs. Ten experienced raters took part in the study. All raters deemed the models suitable for surgical education. No significant differences between ABS and PLA were found, with both having distinct advantages. The study demonstrated that 3D printing with inexpensive printing filaments is a promising method for training oral and maxillofacial surgery residents or dental students in selected surgical procedures. With a simple and cost-efficient manufacturing process, models of actual patient cases can be produced on a small scale, simulating many kinds of surgical procedures. © 2018 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Degradation of physical properties of different elastomers upon exposure to palm biodiesel

International Nuclear Information System (INIS)

Haseeb, A.S.M.A.; Jun, T.S.; Fazal, M.A.; Masjuki, H.H.

2011-01-01

Biodiesel, as an alternative fuel, is gradually receiving more popularity for use in internal combustion engines. However questions continue to arise with regard to its compatibility with elastomeric materials. The present work aims to investigate the comparative degradation of physical properties for different elastomers [e.g. ethylene propylene diene monomer (EPDM), silicone rubber (SR), polychloroprene (CR), polytetrafluroethylene (PTFE) and nitrile rubber (NBR)] upon exposure to diesel and palm biodiesel. Static immersion tests in B0(diesel), B10 (10% biodiesel in diesel), B20, B50 and B100(biodiesel) were carried out at room temperature (25 o C) for 1000 h. Different physical properties like, changes in weight and volume, hardness and tensile strength were measured at every 250 h of immersion time. Compositional changes in biodiesel due to exposure of different elastomers were investigated by Gas chromatography mass spectroscopy (GCMS). The overall sequence of compatible elastomers in palm biodiesel is found to be PTFE > SR > NBR > EPDM > CR. -- Research highlights: → Biodiesel and its blends swelled polychloroprene (CR) and nitrile rubber (NBR) to a greater extent than did diesel. → Although PTFE seems to be the most compatible elastomer among those tested, it undergoes a slight reduction of main constituents. →The overall sequence of compatible elastomers in palm biodiesel is PTFE > SR > NBR > EPDM > CR.

Rapid prototyping-assisted maxillofacial reconstruction.

Science.gov (United States)

Peng, Qian; Tang, Zhangui; Liu, Ousheng; Peng, Zhiwei

2015-05-01

Rapid prototyping (RP) technologies have found many uses in dentistry, and especially oral and maxillofacial surgery, due to its ability to promote product development while at the same time reducing cost and depositing a part of any degree of complexity theoretically. This paper provides an overview of RP technologies for maxillofacial reconstruction covering both fundamentals and applications of the technologies. Key fundamentals of RP technologies involving the history, characteristics, and principles are reviewed. A number of RP applications to the main fields of oral and maxillofacial surgery, including restoration of maxillofacial deformities and defects, reduction of functional bone tissues, correction of dento-maxillofacial deformities, and fabrication of maxillofacial prostheses, are discussed. The most remarkable challenges for development of RP-assisted maxillofacial surgery and promising solutions are also elaborated.

Maxillofacial fractures: twenty years of study in the department of maxillofacial surgery in kosovo.

Science.gov (United States)

Loxha, Mergime Prekazi; Sejfija, Osman; Salihu, Sami; Gjinolli, Fellanza; Agani, Zana; Hamiti, Vjosa; Rexhepi, Aida Namani; Gecaj-Gashi, Agreta

2013-01-01

The aim of this study was to analyze maxillofacial region fractures during the past 20 years in the Department of Maxillofacial Surgery in Prishtina. We have analyzed the histories of all patients with trauma who were hospitalized in the Department of Maxillofacial Surgery in Prishtina since the opening of the clinic in 1983 through 2005. Narrowing the subject of our research, we concentrated on fractures of the maxillofacial region treated at the Clinic of Maxillofacial Surgery for the period 2001-2005. We have analyzed those fractures and compared them with the period from 1983 to 2005 only when it was reasonable. During this period, 1,945 patients were treated for trauma in the maxillofacial region by the Department of Maxillofacial Surgery. This group included 19.8% females and 80.2% males. The largest age group were those between 20 and 20 years of age. Causes of trauma for both periods were predominantly traffic accidents; however, during the period 2001-2005, interpersonal conflicts were increasingly the cause of fractures. Interpersonal conflict as a cause of maxillofacial trauma has risen in recent years. With this increase the methods of treating fractures in this region are also changing.

Temperature dependence of viscoelasticity of crystalline cellulose with different molecular weights added to silicone elastomer

Science.gov (United States)

Sugino, Naoto; Nakajima, Shinya; Kameda, Takao; Takei, Satoshi; Hanabata, Makoto

2017-08-01

Silicone elastomers ( polydimethylsiloxane _ PDMS) are widely used in the field of imprint lithography and microcontactprinting (μCP). When performing microcontactprinting, the mechanical properties of the PCMS as a base material have a great influence on the performance of the device. Cellulose nanofibers having features of high strength, high elasticity and low coefficient of linear expansion have attracted attention in recent years due to their characteristics. Therefore, three types of crystalline cellulose having different molecular weights were added to PDMS to prepare a composite material, and dynamic viscoelasticity was measured using a rheometer. The PDMS with the highest molecular weight crystalline cellulose added exhibited smaller storage modulus than PDMS with other molecular weight added in all temperature ranges. Furthermore, when comparing PDMS to which crystalline cellulose was added and PDMS which is not added, the storage modulus of PDMS to which cellulose was added in the low temperature region was higher than that of PDMS to which it was not added, but it was reversed in the high temperature region It was a result. When used in a low temperature range (less than 150 ° C.), it can be said that cellulose can function as a reinforcing material for PDMS.

Novel encapsulation technique for incorporation of high permittivity fillers into silicone elastomers

DEFF Research Database (Denmark)

Mazurek, Piotr Stanislaw; Hvilsted, Søren; Skov, Anne Ladegaard

2014-01-01

permittivity fillers, 2) Grafting of high permittivity molecules onto the polymer backbone in the elastomer, and 3) Encapsulation of high permittivity fillers. The approach investigated here is a new type of encapsulation which does not interfere with the mechanical properties to the same content...

Novel high dielectric constant hybrid elastomers based on glycerol-insilicone emulsions

DEFF Research Database (Denmark)

Mazurek, Piotr Stanislaw; Skov, Anne Ladegaard

2016-01-01

Novel hybrid elastomers were prepared by speedmixing of two virtually immiscible liquids – glycerol and polydimethylsiloxane (PDMS) prepolymer. Upon crosslinking ofthe PDMS phase of the resulting glycerol-in-silicone emulsion freestanding films were obtained. In this way glycerol became uniformly...... elastomeractuators. Conductivities of samples based on various PDMS compositions with different loadings of embedded glycerol were thoroughly investigated providing useful information about the dielectric behavior....

Mechanical design handbook for elastomers. [the design of elastomer dampers for application in rotating machinery

Science.gov (United States)

Darlow, M.; Zorzi, E.

1981-01-01

A comprehensive guide for the design of elastomer dampers for application in rotating machinery is presented. Theoretical discussions, a step by step procedure for the design of elastomer dampers, and detailed examples of actual elastomer damper applications are included. Dynamic and general physical properties of elastomers are discussed along with measurement techniques.

Mechanical Design Handbook for Elastomers

Science.gov (United States)

Darlow, M.; Zorzi, E.

1986-01-01

Mechanical Design Handbook for Elastomers reviews state of art in elastomer-damper technology with particular emphasis on applications of highspeed rotor dampers. Self-contained reference but includes some theoretical discussion to help reader understand how and why dampers used for rotating machines. Handbook presents step-by-step procedure for design of elastomer dampers and detailed examples of actual elastomer damper applications.

Fracture and healing of elastomers: A phase-transition theory and numerical implementation

Science.gov (United States)

Kumar, Aditya; Francfort, Gilles A.; Lopez-Pamies, Oscar

2018-03-01

A macroscopic theory is proposed to describe, explain, and predict the nucleation and propagation of fracture and healing in elastomers undergoing arbitrarily large quasistatic deformations. The theory, which can be viewed as a natural generalization of the phase-field approximation of the variational theory of brittle fracture of Francfort and Marigo (1998) to account for physical attributes innate to elastomers that have been recently unveiled by experiments at high spatio-temporal resolution, rests on two central ideas. The first one is to view elastomers as solids capable to undergo finite elastic deformations and capable also to phase transition to another solid of vanishingly small stiffness: the forward phase transition serves to model the nucleation and propagation of fracture while the reverse phase transition models the possible healing. The second central idea is to take the phase transition to be driven by the competition between a combination of strain energy and hydrostatic stress concentration in the bulk and surface energy on the created/healed new surfaces in the elastomer. From an applications point of view, the proposed theory amounts to solving a system of two coupled and nonlinear PDEs for the deformation field and an order parameter, or phase field. A numerical scheme is presented to generate solutions for these PDEs in N = 2 and 3 space dimensions. This is based on an efficient non-conforming finite-element discretization, which remains stable for large deformations and elastomers of any compressibility, together with an implicit gradient flow solver, which is able to deal with the large changes in the deformation field that can ensue locally in space and time from the nucleation of fracture. The last part of this paper is devoted to presenting sample simulations of the so-called Gent-Park experiment. Those are confronted with recent experimental results for various types of silicone elastomers.

Current state of craniofacial prosthetic rehabilitation.

Science.gov (United States)

Ariani, Nina; Visser, Anita; van Oort, Robert P; Kusdhany, Lindawati; Rahardjo, Tri Budi W; Krom, Bastiaan P; van der Mei, Henry C; Vissink, Arjan

2013-01-01

This study aimed to review the current state of the techniques and materials used to rehabilitate maxillofacial defects. The MEDLINE and EMBASE databases were searched for articles pertinent to maxillofacial prostheses published from January 1990 to July 2011. The main clinical stages were the subject of analysis. A multidisciplinary approach is preferred when rehabilitating maxillofacial defects. Surgical reconstruction can be used for smaller defects, but larger defects require a prosthesis to achieve an esthetic rehabilitation. Implant retained prostheses are preferred over adhesive prostheses. Silicone elastomer is currently the best material available for maxillofacial prostheses; however, longevity and discoloration, which are greatly influenced by ultraviolet radiation, microorganisms, and environmental factors, remain significant problems. In the near future, the widespread availability and cost effectiveness of digital systems may improve the workflow and outcomes of facial prostheses. Patients report high satisfaction with their prostheses despite some areas that still need improvement. Maxillofacial prostheses are a reliable treatment option to restore maxillofacial defects and improve quality of life. Significant progress has been made in the application of implants for retention and digital technology for designing surgical guides, suprastructures, and craniofacial prostheses. Further improvements are necessary to enhance longevity of prostheses.

Single Stage Silicone Border Molded Closed Mouth Impression Technique-Part II.

Science.gov (United States)

Solomon, E G R

2011-09-01

Functioning of a complete denture depends to a great extent on the impression technique. Several impression techniques have been described in the literature since the turn of this century when Greene [Clinical courses in dental prothesis, 1916] brothers introduced the first scientific system of recording dental impression. Advocates of each technique have their own claim of superiority over the other. The introduction of elastomeric impression materials [Skinner and Cooper, J Am Dent Assoc 51:523-536, 1955] has made possible new techniques of recording impression for complete denture construction. These rubber like materials are of two types; one has a polysulfide base and is popularily known as polysulfide rubber (Thiokol and Mercaptan). The other variety has a silicone base known as silicone rubber or silicone elastomer. Silicone elastomers are available in four different consistencies; a thin easy flowing light bodied material,a creamy medium bodied material, a highly viscous heavy bodied material and a kneadable putty material. This paper describes an active closed mouth impression technique with one stage border molding using putty silicone material as a substitute for low fusing compound.

Steady shear characteristic and behavior of magneto-thermo-elasticity of isotropic MR elastomers

International Nuclear Information System (INIS)

Gao, Wei; Wang, Xingzhe

2016-01-01

The magneto-thermo-elastic steady shear behaviors of isotropic smart composites of silicon rubber matrix randomly filled with ferromagnetic particles, commonly referred to as magnetorheological (MR) elastomers, are investigated experimentally and theoretically in the present study. The strip specimens of the MR elastomer composite with different ferromagnetic particle concentrations are fabricated and implemented for lap-shear tests under both magnetic and thermal fields. It is illustrated that the magneto-thermo-elastic shear modulus of the MR elastomer is markedly enhanced with the volume fraction of ferromagnetic particles and the applied external magnetic field, while the shear modulus is decreased with the environment temperature. To qualitatively elucidate the magneto-thermo-elastic shear performance of this kind of magnetic smart composites, a modified constitutive of hyperelasticity is suggested taking into account the influence of magnetic field and temperature on the magnetic potential energy and strain energy. The theoretical modeling predictions on the stress–strain behaviors for different applied magnetic fields and environment temperatures are compared to experimental observations to demonstrate a good agreement. (paper)

An evaluation of advanced digital colour technology for colour matching maxillofacial prosthetics.

OpenAIRE

Nacher-Garcia, C.

2016-01-01

Aim: To evaluate the reliability and reproducibility of the Spectromatch-Pro digital colour system (Spectromatch Ltd. UK) in the reproduction of simulated skin-silicone colour samples; and to determine threshold Delta E (∆E) (CIE L*a*b*) of perceptible and acceptable colour differences for maxillofacial prosthetics. Method: A two phase quantitative research design. Phase 1: tested; (i) the reproducibility of the spectrophotometer for eight subjects (n=48) scans; from four ethnic groups...

Performance Optimization of a Conical Dielectric Elastomer Actuator

Directory of Open Access Journals (Sweden)

Chongjing Cao

2018-06-01

Full Text Available Dielectric elastomer actuators (DEAs are known as ‘artificial muscles’ due to their large actuation strain, high energy density and self-sensing capability. The conical configuration has been widely adopted in DEA applications such as bio-inspired locomotion and micropumps for its good compactness, ease for fabrication and large actuation stroke. However, the conical protrusion of the DEA membrane is characterized by inhomogeneous stresses, which complicate their design. In this work, we present an analytical model-based optimization for conical DEAs with the three biasing elements: (I linear compression spring; (II biasing mass; and (III antagonistic double-cone DEA. The optimization is to find the maximum stroke and work output of a conical DEA by tuning its geometry (inner disk to outer frame radius ratio a/b and pre-stretch ratio. The results show that (a for all three cases, stroke and work output are maximum for a pre-stretch ratio of 1 × 1 for the Parker silicone elastomer, which suggests the stretch caused by out-of-plane deformation is sufficient for this specific elastomer. (b Stroke maximization is obtained for a lower a/b ratio while a larger a/b ratio is required to maximize work output, but the optimal a/b ratio is less than 0.3 in all three cases. (c The double-cone configuration has the largest stroke while single cone with a biasing mass has the highest work output.

A Recipe for Soft Fluidic Elastomer Robots.

Science.gov (United States)

Marchese, Andrew D; Katzschmann, Robert K; Rus, Daniela

2015-03-01

This work provides approaches to designing and fabricating soft fluidic elastomer robots. That is, three viable actuator morphologies composed entirely from soft silicone rubber are explored, and these morphologies are differentiated by their internal channel structure, namely, ribbed, cylindrical, and pleated. Additionally, three distinct casting-based fabrication processes are explored: lamination-based casting, retractable-pin-based casting, and lost-wax-based casting. Furthermore, two ways of fabricating a multiple DOF robot are explored: casting the complete robot as a whole and casting single degree of freedom (DOF) segments with subsequent concatenation. We experimentally validate each soft actuator morphology and fabrication process by creating multiple physical soft robot prototypes.

3D printing PLA and silicone elastomer structures with sugar solution support material

Science.gov (United States)

Hamidi, Armita; Jain, Shrenik; Tadesse, Yonas

2017-04-01

3D printing technology has been used for rapid prototyping since 1980's and is still developing in a way that can be used for customized products with complex design and miniature features. Among all the available 3D printing techniques, Fused Deposition Modeling (FDM) is one of the most widely used technologies because of its capability to build different structures by employing various materials. However, complexity of parts made by FDM is greatly limited by restriction of using support materials. Support materials are often used in FDM for several complex geometries such as fully suspended shapes, overhanging surfaces and hollow features. This paper describes an approach to 3D print a structure using silicone elastomer and polylactide fiber (PLA) by employing a novel support material that is soluble in water. This support material is melted sugar which can easily be prepared at a low cost. Sugar is a carbohydrate, which is found naturally in plants such as sugarcane and sugar beets; therefore, it is completely organic and eco-friendly. As another advantage, the time for removing this material from the part is considerably less than other commercially available support materials and it can be removed easily by warm water without leaving any trace. Experiments were done using an inexpensive desktop 3D printer to fabricate complex structures for use in soft robots. The results envision that further development of this system would contribute to a method of fabrication of complex parts with lower cost yet high quality.

Energy scavenging strain absorber: application to kinetic dielectric elastomer generator

Science.gov (United States)

Jean-Mistral, C.; Beaune, M.; Vu-Cong, T.; Sylvestre, A.

2014-03-01

Dielectric elastomer generators (DEGs) are light, compliant, silent energy scavengers. They can easily be incorporated into clothing where they could scavenge energy from the human kinetic movements for biomedical applications. Nevertheless, scavengers based on dielectric elastomers are soft electrostatic generators requiring a high voltage source to polarize them and high external strain, which constitutes the two major disadvantages of these transducers. We propose here a complete structure made up of a strain absorber, a DEG and a simple electronic power circuit. This new structure looks like a patch, can be attached on human's wear and located on the chest, knee, elbow… Our original strain absorber, inspired from a sailing boat winch, is able to heighten the external available strain with a minimal factor of 2. The DEG is made of silicone Danfoss Polypower and it has a total area of 6cm per 2.5cm sustaining a maximal strain of 50% at 1Hz. A complete electromechanical analytical model was developed for the DEG associated to this strain absorber. With a poling voltage of 800V, a scavenged energy of 0.57mJ per cycle is achieved with our complete structure. The performance of the DEG can further be improved by enhancing the imposed strain, by designing a stack structure, by using a dielectric elastomer with high dielectric permittivity.

A silicone elastomer vaginal ring for HIV prevention containing two microbicides with different mechanisms of action.

Science.gov (United States)

Fetherston, Susan M; Boyd, Peter; McCoy, Clare F; McBride, Marcella C; Edwards, Karen-Leigh; Ampofo, Stephen; Malcolm, R Karl

2013-02-14

Vaginal rings are currently being developed for the long-term (at least 30 days) continuous delivery of microbicides against human immunodeficiency virus (HIV). Research to date has mostly focused on devices containing a single antiretroviral compound, exemplified by the 25mg dapivirine ring currently being evaluated in a Phase III clinical study. However, there is a strong clinical rationale for combining antiretrovirals with different mechanisms of action in a bid to increase breadth of protection and limit the emergence of resistant strains. Here we report the development of a combination antiretroviral silicone elastomer matrix-type vaginal ring for simultaneous controlled release of dapivirine, a non-nucleoside reverse transcriptase inhibitor, and maraviroc, a CCR5-targeted HIV-1 entry inhibitor. Vaginal rings loaded with 25mg dapivirine and various quantities of maraviroc (50-400mg) were manufactured and in vitro release assessed. The 25mg dapivirine and 100mg maraviroc formulation was selected for further study. A 24-month pharmaceutical stability evaluation was conducted, indicating good product stability in terms of in vitro release, content assay, mechanical properties and related substances. This combination ring product has now progressed to Phase I clinical testing. Copyright © 2012 Elsevier B.V. All rights reserved.

PZT/PLZT - elastomer composites with improved piezoelectric voltage coefficient

Science.gov (United States)

Harikrishnan, K.; Bavbande, D. V.; Mohan, Dhirendra; Manoharan, B.; Prasad, M. R. S.; Kalyanakrishnan, G.

2018-02-01

Lead Zirconate Titanate (PZT) and Lanthanum-modified Lead Zirconate Titanate (PLZT) ceramic sensor materials are widely used because of their excellent piezoelectric coefficients. These materials are brittle, high density and have low achievable piezoelectric voltage coefficients. The density of the sintered ceramics shall be reduced by burnable polymeric sponge method. The achievable porosity level in this case is nearly 60 - 90%. However, the porous ceramic structure with 3-3 connectivity produced by this method is very fragile in nature. The strength of the porous structure is improved with Sylgard®-184 (silicone elastomer) by vacuum impregnation method maintaining the dynamic vacuum level in the range of -650 mm Hg. The elastomer Sylgard®-184 is having low density, low dielectric constant and high compliance (as a resultant stiffness of the composites is increased). To obtain a net dipole moment, the impregnated ceramic composites were subjected to poling treatment with varying conditions of D.C. field and temperature. The properties of the poled PZT/PLZT - elastomer composites were characterized with LCR meter for measuring the dielectric constant values (k), d33 meter used for measuring piezo-electric charge coefficient values (d33) and piezo-electric voltage coefficient (g33) values which were derived from d33 values. The voltage coefficient (g33) values of these composites are increased by 10 fold as compared to the conventional solid ceramics demonstrates that it is possible to fabricate a conformable detector.

Contemporary management of maxillofacial ballistic trauma.

Science.gov (United States)

Breeze, J; Tong, D; Gibbons, A

2017-09-01

Ballistic maxillofacial trauma in the UK is fortunately relatively rare, and generally involves low velocity handguns and shotguns. Civilian terrorist events have, however, shown that all maxillofacial surgeons need to understand how to treat injuries from improvised explosive devices. Maxillofacial surgeons in the UK have also been responsible for the management of soldiers evacuated from Iraq and Afghanistan, and in this review we describe the newer types of treatment that have evolved from these conflicts, particularly that of damage-control maxillofacial surgery. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

Update of patient-specific maxillofacial implant.

Science.gov (United States)

Owusu, James A; Boahene, Kofi

2015-08-01

Patient-specific implant (PSI) is a personalized approach to reconstructive and esthetic surgery. This is particularly useful in maxillofacial surgery in which restoring the complex three-dimensional (3D) contour can be quite challenging. In certain situations, the best results can only be achieved with implants custom-made to fit a particular need. Significant progress has been made over the past decade in the design and manufacture of maxillofacial PSIs. Computer-aided design (CAD)/computer-aided manufacturing (CAM) technology is rapidly advancing and has provided new options for fabrication of PSIs with better precision. Maxillofacial PSIs can now be designed using preoperative imaging data as input into CAD software. The designed implant is then fabricated using a CAM technique such as 3D printing. This approach increases precision and decreases or completely eliminates the need for intraoperative modification of implants. The use of CAD/CAM-produced PSIs for maxillofacial reconstruction and augmentation can significantly improve contour outcomes and decrease operating time. CAD/CAM technology allows timely and precise fabrication of maxillofacial PSIs. This approach is gaining increasing popularity in maxillofacial reconstructive surgery. Continued advances in CAD technology and 3D printing are bound to improve the cost-effectiveness and decrease the production time of maxillofacial PSIs.

Current concepts in maxillofacial imaging

Energy Technology Data Exchange (ETDEWEB)

Boeddinghaus, Rudolf [Perth Radiological Clinic, 127 Hamersley Road, Subiaco, Western Australia 6008 (Australia)], E-mail: rboeddinghaus@perthradclinic.com.au; Whyte, Andy [Perth Radiological Clinic, 127 Hamersley Road, Subiaco, Western Australia 6008 (Australia)], E-mail: awhyte@perthradclinic.com.au

2008-06-15

A review of state-of-the-art maxillofacial imaging is presented. Current imaging techniques include intra-oral radiographs, dental panoramic tomography, multidetector helical computed tomography, cone-beam computed tomography (CBCT) and magnetic resonance imaging (MRI). The commonest conditions encountered in clinical radiological practice are reviewed, including maxillofacial deformities, complicated dental impactions, maxillofacial trauma, jaw lesions (cysts, neoplasms, fibro-osseous lesions (FOLs) and infections), and temporomandibular joint pathology. Pre-operative assessment for dental implant placement is also briefly reviewed.

Sustainable Elastomers from Renewable Biomass.

Science.gov (United States)

Wang, Zhongkai; Yuan, Liang; Tang, Chuanbing

2017-07-18

Sustainable elastomers have undergone explosive growth in recent years, partly due to the resurgence of biobased materials prepared from renewable natural resources. However, mounting challenges still prevail: How can the chemical compositions and macromolecular architectures of sustainable polymers be controlled and broadened? How can their processability and recyclability be enabled? How can they compete with petroleum-based counterparts in both cost and performance? Molecular-biomass-derived polymers, such as polymyrcene, polymenthide, and poly(ε-decalactone), have been employed for constructing thermoplastic elastomers (TPEs). Plant oils are widely used for fabricating thermoset elastomers. We use abundant biomass, such as plant oils, cellulose, rosin acids, and lignin, to develop elastomers covering a wide range of structure-property relationships in the hope of delivering better performance. In this Account, recent progress in preparing monomers and TPEs from biomass is first reviewed. ABA triblock copolymer TPEs were obtained with a soft middle block containing a soybean-oil-based monomer and hard outer blocks containing styrene. In addition, a combination of biobased monomers from rosin acids and soybean oil was formulated to prepare triblock copolymer TPEs. Together with the above-mentioned approaches based on block copolymers, multigraft copolymers with a soft backbone and rigid side chains are recognized as the first-generation and second-generation TPEs, respectively. It has been recently demonstrated that multigraft copolymers with a rigid backbone and elastic side chains can also be used as a novel architecture of TPEs. Natural polymers, such as cellulose and lignin, are utilized as a stiff, macromolecular backbone. Cellulose/lignin graft copolymers with side chains containing a copolymer of methyl methacrylate and butyl acrylate exhibited excellent elastic properties. Cellulose graft copolymers with biomass-derived polymers as side chains were

Dielectric Elastomers for Fluidic and Biomedical Applications

Science.gov (United States)

McCoul, David James

other smaller particulate debris into the system. After a channel blockage was confirmed, three actuation attempts successfully cleared the blockage. Further tests indicated that the device were biocompatible with HeLa cells at 3 kV. To our knowledge this is the first pairing of dielectric elastomers with microfluidics in a non-electroosmotic context. Applications may include adaptive microfilters, micro-peristaltic pumps, and reduced-complexity lab-on-a-chip devices. Dielectric elastomers can also be adapted to manipulate fluidic systems on a larger scale. The second part of the dissertation research reports a novel low-profile, biomimetic dielectric elastomer tubular actuator capable of actively controlling hydraulic flow. The tubular actuator has been established as a reliable tunable valve, pinching a secondary silicone tube completely shut in the absence of a fluidic pressure bias or voltage, offering a high degree of resistance against fluidic flow, and able to open and completely remove this resistance to flow with an applied low power actuation voltage. The system demonstrates a rise in pressure of ~3.0 kPa when the dielectric elastomer valve is in the passive, unactuated state, and there is a quadratic fall in this pressure with increasing actuation voltage, until ~0 kPa is reached at 2.4 kV. The device is reliable for at least 2,000 actuation cycles for voltages at or below 2.2 kV. Furthermore, modeling of the actuator and fluidic system yields results consistent with the observed experimental dependence of intrasystem pressure on input flow rate, actuator prestretch, and actuation voltage. To our knowledge, this is the first actuator of its type that can control fluid flow by directly actuating the walls of a tube. Potential applications may include an implantable artificial sphincter, part of a peristaltic pump, or a computerized valve for fluidic or pneumatic control. The final part of the dissertation presents a novel dielectric elastomer band with

Effect of organo-clay on the dielectric relaxation response of silicone rubber

International Nuclear Information System (INIS)

Gharavi, N; Razzaghi-Kashani, M; Golshan-Ebrahimi, N

2010-01-01

Dielectric elastomers are light weight, low-cost, highly deformable and fast response smart materials capable of converting electrical energy into mechanical work or vice versa. Silicone rubber is a well-known dielectric elastomer which is used as actuator, and in order to enhance the efficiency of this smart material, compounding of silicone rubber with various fillers can be carried out. The effect of organically modified montmorillonite (OMMT) nano-clay on improvement of dielectric properties, actuation stress and its relaxation response was considered in this study. OMMT was dispersed in room temperature vulcanized (RTV) silicone rubber, and a composite film was cast. Using an in-house actuation set-up, it was shown that the actuation stress for a given electric field intensity is higher for composites than that for pristine silicone rubber. Also, the time-dependent actuation response of the samples was evaluated, and it was shown that the characteristic relaxation time of the actuation stress for composites is less than for the pristine rubber as a result of OMMT addition

Microstructure of dimethylsiloxane based magnetic elastomers

International Nuclear Information System (INIS)

Balasoiu, M.; Craus, M.L.; Anitas, E.M.; Bica, I.; Plestil, J.; Kuklin, A.I.

2009-01-01

Dimethylsiloxane based elastomers filled with two types of magnetic particles (nano- and micro-sized) were investigated. It was obtained that doping with Fe 3 O 4 nanoparticles and applying of magnetic field during the polymerization process leads to a significant change of the local structure of elastomer. After filling the polymer with Fe 3 O 4 nanoparticles the magnetic elastomer presents a mass fractal structure. The mass fractal dimension is decreasing in the magnetic elastomer polymerized in magnetic field. For the elastomer filled with a large amount of Fe microparticles (75% particle concentration) a texture effect is detected; for the samples polymerized in magnetic field the texture effect is higher. Surface fractal property is obtained for all microparticle concentrations

Monitoring diver kinematics with dielectric elastomer sensors

Science.gov (United States)

Walker, Christopher R.; Anderson, Iain A.

2017-04-01

Diving, initially motivated for food purposes, is crucial to the oil and gas industry, search and rescue, and is even done recreationally by millions of people. There is a growing need however, to monitor the health and activity of divers. The Divers Alert Network has reported on average 90 fatalities per year since 1980. Furthermore an estimated 1000 divers require recompression treatment for dive-related injuries every year. One means of monitoring diver activity is to integrate strain sensors into a wetsuit. This would provide kinematic information on the diver potentially improving buoyancy control assessment, providing a platform for gesture communication, detecting panic attacks and monitoring diver fatigue. To explore diver kinematic monitoring we have coupled dielectric elastomer sensors to a wetsuit worn by the pilot of a human-powered wet submarine. This provided a unique platform to test the performance and accuracy of dielectric elastomer strain sensors in an underwater application. The aim of this study was to assess the ability of strain sensors to monitor the kinematics of a diver. This study was in collaboration with the University of Auckland's human-powered submarine team, Team Taniwha. The pilot, completely encapsulated in a hull, pedals to propel the submarine forward. Therefore this study focused on leg motion as that is the primary motion of the submarine pilot. Four carbon-filled silicone dielectric elastomer sensors were fabricated and coupled to the pilot's wetsuit. The first two sensors were attached over the knee joints, with the remaining two attached between the pelvis and thigh. The goal was to accurately measure leg joint angles thereby determining the position of each leg relative to the hip. A floating data acquisition unit monitored the sensors and transmitted data packets to a nearby computer for real-time processing. A GoPro Hero 4 silver edition was used to capture the experiments and provide a means of post-validation. The

Impregnation of soft biological specimens with thermosetting resins and elastomers.

Science.gov (United States)

von Hagens, G

1979-06-01

A new method for impregnation of biological specimens with thermosetting resins and elastomers is described. The method has the advantage that the original relief of the surface is retained. The impregnation is carried out by utilizing the difference between the high vapor tension of the intermedium (e.g., methylene chloride) and the low vapor tension of the solution to be polymerized. After impregnation, the specimen is subject to polymerization conditions without surrounding embedding material. The optical and mechanical properties can be selected by proper choice from various kinds of resins and different procedures, for example, by complete or incomplete impregnation. Acrylic resins, polyester resins, epoxy resins, polyurethanes and silicone rubber have been found suitable for the method. Excellent results have been obtained using transparent silicone rubber since after treatment the specimens are still flexible and resilient, and have retained their natural appearance.

Asymmetric Dielectric Elastomer Composite Material

Science.gov (United States)

Stewart, Brian K. (Inventor)

2014-01-01

Embodiments of the invention provide a dielectric elastomer composite material comprising a plurality of elastomer-coated electrodes arranged in an assembly. Embodiments of the invention provide improved force output over prior DEs by producing thinner spacing between electrode surfaces. This is accomplished by coating electrodes directly with uncured elastomer in liquid form and then assembling a finished component (which may be termed an actuator) from coated electrode components.

Reduction of the Adhesive Friction of Elastomers through Laser Texturing of Injection Molds

Directory of Open Access Journals (Sweden)

Joel Voyer

2017-11-01

Full Text Available It is well known that elastomers usually possess poor dry sliding friction properties due to their highly adhesive character. In order to overcome this problematic behavior in industrial applications, interfacial materials such as oils, greases, coatings, or lacks are normally used in order to separate or to functionalize the contact surfaces of elastomers. Alternatively, the high adhesion tendency of elastomers may be explicitly reduced by modifying the elastomer composition itself or by enabling a reduction of its effective contact area through, for example, surface laser texturing. This second approach, i.e., the reduction of the adhesive character of elastomers through laser structuring, will be the main topic of the present study. For this purpose, different micro-sized grooved structures were produced on flat injection molds using an ultra-short pulsed laser. The micro-structured molds were then used to produce injection molded micro-ridged Liquid Silicone Rubber (LSR sample pads. The investigations consisted firstly of determining the degree of replication of the mold micro-structures onto the surface of the LSR pads and secondly, to ascertain the degree of reduction of the friction force (or coefficient of friction of these micro-ridged LSR pads in comparison to the benchmark (unstructured LSR pads when tested under dry conditions against Aluminum alloy (Al-6082 or PA6.6-GF30 plates. For this second part of the investigation, the normal force (or contact pressure dependency of the coefficient of friction was determined through stepwise load increasing friction tests. The results of these investigations have shown that the production of micro-ridged surfaces on LSR pads through laser structuring of the injection molds could be successfully achieved and that it enables a significant reduction of the friction force for low normal forces (or contact pressures, where the component of adhesion friction is playing an important and determining

High-strain actuator materials based on dielectric elastomers

DEFF Research Database (Denmark)

Pelrine, R.; Kornbluh, R.; Kofod, G.

2000-01-01

Dielectric elastomers are a new class of actuator materials that exhibit excellent performance. The principle of operation, as well as methods to fabricate and test these elastomers, is summarized here. The Figure is a sketch of an elastomer film (light gray) stretched on a frame (black) and patt......Dielectric elastomers are a new class of actuator materials that exhibit excellent performance. The principle of operation, as well as methods to fabricate and test these elastomers, is summarized here. The Figure is a sketch of an elastomer film (light gray) stretched on a frame (black...

Implementation of Statistical Process Control: Evaluating the Mechanical Performance of a Candidate Silicone Elastomer Docking Seal

Science.gov (United States)

Oravec, Heather Ann; Daniels, Christopher C.

2014-01-01

The National Aeronautics and Space Administration has been developing a novel docking system to meet the requirements of future exploration missions to low-Earth orbit and beyond. A dynamic gas pressure seal is located at the main interface between the active and passive mating components of the new docking system. This seal is designed to operate in the harsh space environment, but is also to perform within strict loading requirements while maintaining an acceptable level of leak rate. In this study, a candidate silicone elastomer seal was designed, and multiple subscale test articles were manufactured for evaluation purposes. The force required to fully compress each test article at room temperature was quantified and found to be below the maximum allowable load for the docking system. However, a significant amount of scatter was observed in the test results. Due to the stochastic nature of the mechanical performance of this candidate docking seal, a statistical process control technique was implemented to isolate unusual compression behavior from typical mechanical performance. The results of this statistical analysis indicated a lack of process control, suggesting a variation in the manufacturing phase of the process. Further investigation revealed that changes in the manufacturing molding process had occurred which may have influenced the mechanical performance of the seal. This knowledge improves the chance of this and future space seals to satisfy or exceed design specifications.

Custom 3D Printable Silicones with Tunable Stiffness.

Science.gov (United States)

Durban, Matthew M; Lenhardt, Jeremy M; Wu, Amanda S; Small, Ward; Bryson, Taylor M; Perez-Perez, Lemuel; Nguyen, Du T; Gammon, Stuart; Smay, James E; Duoss, Eric B; Lewicki, James P; Wilson, Thomas S

2018-02-01

Silicone elastomers have broad versatility within a variety of potential advanced materials applications, such as soft robotics, biomedical devices, and metamaterials. A series of custom 3D printable silicone inks with tunable stiffness is developed, formulated, and characterized. The silicone inks exhibit excellent rheological behavior for 3D printing, as observed from the printing of porous structures with controlled architectures. Herein, the capability to tune the stiffness of printable silicone materials via careful control over the chemistry, network formation, and crosslink density of the ink formulations in order to overcome the challenging interplay between ink development, post-processing, material properties, and performance is demonstrated. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Prosthetic rehabilitation of large mid-facial defect with magnet-retained silicone prosthesis

Directory of Open Access Journals (Sweden)

Kirti Jajoo Shrivastava

2015-01-01

Full Text Available Rehabilitation of maxillofacial defect patients is a challenging task. The most common prosthetic treatment problem with such patients is, getting adequate retention, stability, and support. In cases of large maxillofacial defect, movement of the prosthesis is inevitable. The primary objectives in rehabilitating the maxillofacial defect patients are to restore the function of mastication, deglutition, speech, and to achieve normal orofacial appearance. This clinical report describes maxillofacial prosthetic rehabilitation of large midfacial defect including orbit along with its contents, zygoma and soft tissues including half of the nose, cheeks, upper lip of left side, accompanying postsurgical microstomia and orofacial communication, which resulted from severe fungal infection mucormycosis. The defect in this case was restored with magnet retained two piece maxillofacial prosthesis having hollow acrylic resin framework and an overlying silicone facial prosthesis. The retention of prosthesis was further enhanced with the use of spectacles. This type of combination prosthesis enhanced the cosmesis and functional acceptability of prosthesis.

Collapse of Non-Rectangular Channels in a Soft Elastomer

Science.gov (United States)

Tepayotl-Ramirez, Daniel; Park, Yong-Lae; Lu, Tong; Majidi, Carmel

2013-03-01

We examine the collapse of microchannels in a soft elastomer by treating the sidewalls as in- denters that penetrate the channel base. This approach leads to a closed-form algebraic mapping between applied pressure and cross-sectional deformation that are in strong agreement with ex- perimental measurements and Finite Element Analysis (FEA) simulation. Applications of this new approach to modeling soft microchannel collapse range from lab-on-a-chip microfluidics for pressure-controlled protein filtration to soft-matter pressures sensing. We demonstrate the latter by comparing theoretical predictions with experimental measurements of the pressure-controlled electrical resistance of liquid-phase Gallium alloy microchannels embedded in a soft silicone elas- tomer.

Maxillofacial trauma due to work-related accidents.

Science.gov (United States)

Hächl, O; Tuli, T; Schwabegger, A; Gassner, R

2002-02-01

Even though numerous reports on maxillofacial trauma exist, only a few give detailed information about work-related maxillofacial injuries. The purpose of this study was to reveal the significance of maxillofacial injuries related to accidents occurring at work by evaluating a large number of patients with maxillofacial injuries over a 9-year period. Out of the 8704 trauma patients treated between 1991 and 1999 in the Department of Oral and Maxillofacial Surgery at the University of Innsbruck, Austria, 463 (5.4%) were injured at work. All charts were reviewed and analyzed according to age, gender, cause of accident, occupation, type of injury, location and frequency of fractures. The highest incidence of maxillofacial injury was found among construction workers (a total of 124 patients, 26.8%), followed by craftsmen (102 patients, 22.0%) and office employees (69 patients, 14.9%). The sex distribution showed an overall male-to-female ratio of 11.8:1 and those in the age group most affected were between 20 and 29 years of age. The most frequent cause of injury was a blow in 48.4%, followed by falls and falls over obstacles, accounting for 27.9% and 7.1%, respectively. Of all trauma, 45.4% (210 persons) sustained 423 maxillofacial fractures, 31.7% (147 patients) suffered 232 dento-alveolar injuries, and 21.2% (98 people) showed 430 soft-tissue injuries. One-fifth (20.7%) of all patients displayed concomitant injuries with cerebral and cranial trauma being the most common. The probability of sustaining maxillofacial trauma at work is correlated to the nature of the occupation. Individuals (mostly men) using tools or machines at work are exposed to a much higher risk of work-related maxillofacial trauma.

Electrospraying and ultraviolet light curing of nanometer-thin polydimethylsiloxane membranes for low-voltage dielectric elastomer transducers

Science.gov (United States)

Osmani, Bekim; Töpper, Tino; Siketanc, Matej; Kovacs, Gabor M.; Müller, Bert

2017-04-01

Dielectric elastomer transducers (DETs) have attracted interest as actuators, sensors, and even as self-sensing actuators for applications in medicine, soft robotics, and microfluidics. To reach strains of more than 10 %, they currently require operating voltages of several hundred volts. In medical applications for artificial muscles, however, their operation is limited to a very few tens of volts, which implies high permittivity materials and thin-film structures. Such micro- or nanostructures can be prepared using electro-spraying, a cost-effective technique that allows upscaling using multiple nozzles for the fabrication of silicone films down to nanometer thickness. Deposition rates of several micrometers per hour have already been reached. It has been recently demonstrated that such membranes can be fabricated by electro-spraying and subsequent ultraviolet light irradiation. Herein, we introduce a relatively fast deposition of a dimethyl silicone copolymer fluid that contains mercaptopropyl side chains in addition to the methyl groups. Its elastic modulus was tuned with the irradiation dose of the 200 W Hg-Xe lamp. We also investigated the formation of elastomer films, using polymer concentrations in ethyl acetate of 1, 2, 5 and 10 vol%. After curing, the surface roughness was measured by means of atomic force microscopy. This instrument also enabled us to determine the average elastic modulus out of, for example, 400 nanoindentation measurements, using a spherical tip with a radius of 500 nm. The elastomer films were cured for a period of less than one minute, a speed that makes it feasible to combine electro-spraying and in situ curing in a single process step for fabricating low-voltage, multilayer DETs.

Biodegradable xylitol-based elastomers: In vivo behavior and biocompatibility

NARCIS (Netherlands)

J.P. Bruggeman (Joost); C.J. Bettinger (Christopher); R.S. Langer (Robert)

2010-01-01

textabstractBiodegradable elastomers based on polycondensation reactions of xylitol with sebacic acid, referred to as poly(xylitol sebacate) (PXS) elastomers have recently been developed. We describe the in vivo behavior of PXS elastomers. Four PXS elastomers were synthesized, characterized, and

The implicit effect of texturizing field on the elastic properties of magnetic elastomers revealed by SANS

Energy Technology Data Exchange (ETDEWEB)

Balasoiu, M., E-mail: balas@jinr.ru [Joint Institute of Nuclear Research, Dubna (Russian Federation); Horia Hulubei National Institute for Physics and Nuclear Engineering, Bucharest (Romania); Lebedev, V.T. [St.Petersburg Nuclear Physics Institute NRC KI, Gatchina (Russian Federation); Raikher, Yu.L. [Institute of Continuous Media Mechanics, Russian Academy of Sciences, Ural Branch, Perm (Russian Federation); Bica, I.; Bunoiu, M. [West University of Timisoara, Department of Physics (Romania)

2017-06-01

Small angle neutron scattering method (SANS) is used to characterize the structure properties of the polymer matrix of magnetic elastomers (MEs) of the same material content but with different magnetic textures. For that, series of silicone-rubber elastomers mixed with a ferrofluid and polymerized with/without external magnetic field were studied. In the species of pure rubber and the ME samples synthesized without field, SANS reveals a substantial number of large polymer coils (blobs) which are vertically prolate. The case of MEs polymerized under the magnetic field that is also vertically directed, is different. SANS data indicates that there the blobs are preferably elongated in the direction normal to the field. - Highlights: • SANS method is used to determine the structure of SR elastomers polymerized with ferrofluid in/no external magnetic field. • In the rubber and ME samples synthesized without field, SANS reveals a substantial number of vertically prolate blobs. • For MEs polymerized in vertical magnetic field, results that the blobs are elongated in the direction normal to the field. • Isotropic and texturized MEs differ by the filler structure and by intrinsic elastic properties of the matrix as well.

The pressure-dependent MR effect of magnetorheological elastomers

International Nuclear Information System (INIS)

Dong, Xufeng; Qi, Min; Chen, Ran; Ma, Ning; Li, Jinhai; Ou, Jinping

2012-01-01

The mechanism for the influence of the normal pressure on the magnetic-induced shear modulus of magnetorheological elastomers (MREs) was analyzed. Pre-structured MRE samples with 30% micro-sized (∼4 μm) carbonyl iron particles by volume fraction and silicon rubber were prepared under a constant magnetic field of 200 kA m −1 . A parallel-plate MR rheometer was used to conduct dynamic measurements. Under constant strain amplitude (1%) and frequency (10 Hz), different normal pressures (32–128 kPa) were applied on the samples to investigate the normal pressure-dependence properties of MREs. The results indicated that as the normal pressure increases, the magnetic-induced shear modulus of an MRE increases, while the relative MR effect decreases. (paper)

Hyperelastic pressure sensing with a liquid-embedded elastomer

International Nuclear Information System (INIS)

Park, Yong-Lae; Wood, Robert J; Majidi, Carmel; Kramer, Rebecca; Bérard, Phillipe

2010-01-01

A hyperelastic pressure transducer is fabricated by embedding silicone rubber with microchannels of conductive liquid eutectic gallium–indium. Pressing the surface of the elastomer with pressures in the range of 0–100 kPa will deform the cross-section of underlying channels and change their electric resistance by as much as 50%. Microchannels with dimensions as small as 25 µm are obtained with a maskless, soft lithography process that utilizes direct laser exposure. Change in electrical resistance is measured as a function of the magnitude and area of the surface pressure as well as the cross-sectional geometry, depth and relative lateral position of the embedded channel. These experimentally measured values closely match closed-form theoretical predictions derived from plane strain elasticity and contact mechanics

Elastomer Reinforced with Carbon Nanotubes

Science.gov (United States)

Hudson, Jared L.; Krishnamoorti, Ramanan

2009-01-01

Elastomers are reinforced with functionalized, single-walled carbon nanotubes (SWNTs) giving them high-breaking strain levels and low densities. Cross-linked elastomers are prepared using amine-terminated, poly(dimethylsiloxane) (PDMS), with an average molecular weight of 5,000 daltons, and a functionalized SWNT. Cross-link densities, estimated on the basis of swelling data in toluene (a dispersing solvent) indicated that the polymer underwent cross-linking at the ends of the chains. This thermally initiated cross-linking was found to occur only in the presence of the aryl alcohol functionalized SWNTs. The cross-link could have been via a hydrogen-bonding mechanism between the amine and the free hydroxyl group, or via attack of the amine on the ester linage to form an amide. Tensile properties examined at room temperature indicate a three-fold increase in the tensile modulus of the elastomer, with rupture and failure of the elastomer occurring at a strain of 6.5.

Thermodynamics and instability of dielectric elastomer (Conference Presentation)

Science.gov (United States)

Liu, Liwu; Liu, Yanju; Leng, Jinsong; Mu, Tong

2017-04-01

Dielectric elastomer is a kind of typical soft active material. It can deform obviously when subjected to an external voltage. When a dielectric elastomer with randomly oriented dipoles is subject to an electric field, the dipoles will rotate to and align with the electric field. The polarization of the dielectric elastomer may be saturated when the voltage is high enough. When subjected to a mechanical force, the end-to-end distance of each polymer chain, which has a finite contour length, will approach the finite value, reaching a limiting stretch. On approaching the limiting stretch, the elastomer stiffens steeply. Here, we develop a thermodynamic constitutive model of dielectric elastomers undergoing polarization saturation and strain-stiffening, and then investigate the stability (electromechanical stability, snap-through stability) and voltage induced deformation of dielectric elastomers. Analytical solution has been obtained and it reveals the marked influence of the extension limit and polarization saturation limit on its instability. The developed thermodynamic constitutive model and simulation results would be helpful in future to the research of dielectric elastomer based high-performance transducers.

Compatibility of selected elastomers with plutonium glovebox environment

International Nuclear Information System (INIS)

Burns, R.

1994-06-01

This illustrative test was undertaken as a result of on-going failure of elastomer components in plutonium gloveboxes. These failures represent one of the major sources of required maintenance to keep gloveboxes operational. In particular, it was observed that the introduction of high specific activity Pu-238 into a glovebox, otherwise contaminated with Pu-239, resulted in an inordinate failure of elastomer components. Desiring to keep replacement of elastomer components to a minimum, a decision to explore a few possible alternative elastomer candidates was undertaken and reported upon herewith. Sample specimens of Neoprene, Urethane, Viton, and Hypalon elastomeric formulations were obtained from the Bacter Rubber Company. Strips of the elastomer specimens were placed in a plutonium glovebox and outside of a glovebox, and were observed for a period of three years. Of the four types of elastomers, only Hypalon remained completely viable

A soft and conductive PDMS-PEG block copolymer as a compliant electrode for dielectric elastomers

DEFF Research Database (Denmark)

A Razak, Aliff Hisyam; Szabo, Peter; Skov, Anne Ladegaard

Conductive PDMS-PEG block copolymers (Mn = 3 – 5 kg/mol) were chain-extended (Mn = 30 – 45 kg/mol) using hydrosilylation reaction as presented in figure 1. Subsequently, the extended copolymers were added to a conductive nano-filler (multi-walled carbon nanotubes – MWCNTs) in order to enhance...... conductivity. The combination of soft chainextended PDMS-PEG block copolymers and conductive MWCNTs results in a soft and conductive block copolymer composite which potentially can be used as a compliant and highly stretchable electrode for dielectric elastomers. The addition of MWCNTs into the PDMS-PEG matrix...... MWCNTs is 10-3 S/cm compared to 10-1 S/cm of a non-stretchable reference conducting silicone elastomer (LR3162 from Wacker). Furthermore, PDMS-PEG block copolymer with 4 phr MWCNTs (Young’s modulus, Y = 0.26 MPa) is softer and more stretchable thanLR3162 (Y = 1.17 MPa)....

Negative Pressure Wound Therapy in Maxillofacial Applications

Directory of Open Access Journals (Sweden)

Adam J. Mellott

2016-09-01

Full Text Available Negative pressure wound therapy has greatly advanced the field of wound healing for nearly two decades, by providing a robust surgical adjunct technique for accelerating wound closure in acute and chronic wounds. However, the application of negative pressure wound therapy in maxillofacial applications has been relatively under utilized as a result of the physical articulations and contours of the head and neck that make it challenging to obtain an airtight seal for different negative pressure wound therapy systems. Adapting negative pressure wound therapies for maxillofacial applications could yield significant enhancement of wound closure in maxillofacial applications. The current review summarizes the basic science underlying negative pressure wound therapy, as well as specific maxillofacial procedures that could benefit from negative pressure wound therapy.

Dielectric elastomer actuators used for pneumatic valve technology

International Nuclear Information System (INIS)

Giousouf, Metin; Kovacs, Gabor

2013-01-01

Dielectric elastomer actuators have been investigated for applications in the field of pneumatic automation technology. We have developed different valve designs with stacked dielectric elastomer actuators and with integrated high voltage converters. The actuators were made using VHB-4910 material and a stacker machine for automated fabrication of the cylindrical actuators. Typical characteristics of pneumatic valves such as flow rate, power consumption and dynamic behaviour are presented. For valve construction the force and stroke parameters of the dielectric elastomer actuator have been measured. Further, benefits for valve applications using dielectric elastomers are shown as well as their potential operational area. Finally, challenges are discussed that are relevant for the use of elastomer actuators in valves for industrial applications. (paper)

The relationship between elastomer opacity, colorimeter beam size, and measured colorimetric response.

Science.gov (United States)

Rugh, E H; Johnston, W M; Hesse, N S

1991-01-01

The effect of opacity on the colorimetric responses of large-area and small-area colorimeters was determined using an elastomer intended for maxillofacial prosthetics use and containing various pigments at different concentrations. Opacity was determined by calculating the contrast ratio of 2-mm-thick specimens against black and white backings, using Kubelka-Munk analyses to correct for thickness and backing color variations. The measure of comparison of the two colorimeters was the relative difference in tristimulus reflectance, with the tristimulus reflectance of the large-area colorimeter as the basis of the relative difference. A significant quadratic relationship was found between contrast ratio and the relative difference in tristimulus reflectance. This relationship may be used to describe opacity without the need to make optical observations or measurements of a thin layer of material on contrasting backings. The small-area colorimeter produced color parameters that are a measure of the combined effects of both color and opacity. The importance of beam size considerations of optical measuring devices for translucent natural and prosthetic materials was emphasized.

Inorganic particle analysis of dental impression elastomers.

Science.gov (United States)

Carlo, Hugo Lemes; Fonseca, Rodrigo Borges; Soares, Carlos José; Correr, Américo Bortolazzo; Correr-Sobrinho, Lourenço; Sinhoreti, Mário Alexandre Coelho

2010-01-01

The aim of this study was to determine quantitatively and qualitatively the inorganic particle fraction of commercially available dental elastomers. The inorganic volumetric fraction of two addition silicones (Reprosil Putty/Fluid and Flexitime Easy Putty/Fluid), three condensation silicones (Clonage Putty/Fluid, Optosil Confort/Xantopren VL and Silon APS Putty/Fluid), one polyether (Impregum Soft Light Body) and one polysulfide (Permlastic Light Body) was accessed by weighing a previously determined mass of each material in water before and after burning samples at 600 ºC, during 3 h. Unsettled material samples were soaked in acetone and chloroform for removal of the organic portion. The remaining filler particles were sputter-coated with gold evaluation of their morphology and size, under scanning electron microscopy (SEM). Flexitime Easy Putty was the material with the highest results for volumetric particle fraction, while Impregum Soft had the lowest values. Silon 2 APS Fluid presented the lowest mean filler size values, while Clonage Putty had the highest values. SEM micrographs of the inorganic particles showed several morphologies - lathe-cut, spherical, spherical-like, sticks, and sticks mixed to lathe-cut powder. The results of this study revealed differences in particle characteristics among the elastometic materials that could lead to different results when testing mechanical properties.

INCIDENCE OF MAXILLOFACIAL TRAUMA IN SONEPAT (HARYANA, INDIA

Directory of Open Access Journals (Sweden)

Malik SUNITA

2013-03-01

Full Text Available Background: Maxillofacial injuries represent a therapeutic challenge to oral and maxillofacial surgeons working in emerging countries. This study was carried out to determine the incidence of maxillofacial trauma, clinical management and associated complications. This study highlights the need of oral and maxillofacial surgery along with other disciplines to deliver the emergency services and management to the maxillofacial trauma patients. Patients and Methods: A prospective Medical institute study of maxillofacial injured patients was carried out between September 20122 and December 2012, at the recently founded B.P.S Government Medical College for women, Khanpur kalan, Sonepat, Data regarding incidence, age and sex distribution, causes, types and site of injury, treatment modalities and trauma associated complications were collected and analysed. Results: A total of 462 patients were studied. Males outnumbered females by a ratio of 2.9:1. age range was 9 months to 75 years with the peak incidence occurring in the age group 17-34 years .Most injuries were caused by road traffic accidents (75.8%, followed by assault and falls in 10.6% and 8% respectively. Soft tissue injuries and mandibular fractures were the most common type of injuries. Head/neck (53.1% and limb injuries (28.1% were the most prevalent associated injuries. Surgical debridement and soft tissue suturing (95.1% were the most common surgical procedures. Closed reduction of maxillofacial fractures was employed in 56% of patients, Open reduction and internal fixation was performed in 35% of cases and 9% were managed conservatively. Complications occurred in 3.4% of patients, mainly due to infection and malocclusion. The mean duration of hospital stay was 10.12 ± 6.24 days. Conclusion: This study highlights the importance of Dental surgery department alongwith other disciplinaes in the management of maxillofacial injuries. Moreover there is a need to reinforce legislation aimed to

Magnetoactive elastomer as an element of a magnetic retina fixator

Science.gov (United States)

Makarova, L. A.; Nadzharyan, T. A.; Alekhina, Yu A.; Stepanov, G. V.; Kazimirova, E. G.; Perov, N. S.; Kramarenko, E. Yu

2017-09-01

We explore the possibility of creating an effective retinal fixator on the basis of magnetoactive elastomers (MAEs) and systems of permanent magnets. MAEs consist of silicone elastomer matrix with embedded magnetic iron microparticles. We study theoretically and experimentally magnetic forces acting between MAE samples and permanent magnets in various configurations. The theoretical model is based around classical magnetostatics and Maxwell equations with different parameters accounting for peculiarities of the material and the setup. Approximation of the experimentally measured magnetization curves for MAE samples was used to find input parameters for the theoretical model. To test the model, we conducted a series of experimental measurements of magnetic forces accompanied by model predictions for the system of one cylindrical magnet and a cuboid MAE sample. Calculated dependences of the average pressure arising from magnetic interactions on the distance between the closest faces of MAE samples and a permanent magnet are in a good agreement with the experimental data. The proof on concept for smaller magnetic systems required for eye surgery includes data for 10 magnets configuration and a thin MAE band. This research demonstrates high prospects of using MAE as an element of a magnetic fixator for treatment of complicated retinal detachments.

Vertically aligned nanowires on flexible silicone using a supported alumina template prepared by pulsed anodization

DEFF Research Database (Denmark)

Mátéfi-Tempfli, Stefan; Mátéfi-Tempfli, M.

2009-01-01

Carpets of vertically aligned nanowires on flexible substrates are successfully realized by a template method. Applying special pulsed anodization conditions, defect-free nanoporous alumina structures supported on polydimethylsiloxane (PDMS), a flexible silicone elastomer, are created. By using...... this template with nanopores ending on a conducting underlayer, a high-density nanowire array can be simply grown by direct DCelectrodeposition on the top of the silicone rubber....

Radiographic evaluation of maxillofacial fractures

International Nuclear Information System (INIS)

Litwan, M.; Fliegel, C.

1986-01-01

The course and configuration of typical maxillofacial fractures (type Le Fort I-III) and lateral maxillary fractures including the zygomatic arch were reconstructed in detail by application of barium paste on a bony skull and radiogrpahs in standard projections were performed and evaluated. It was obvious from the resulting radiographs that for most maxillofacial fractures a half axial or Water's view was most helpful. Lateral views only give additional information when there is a considerable degree of dislocation of fragments. Comparison with a prediatric skull of 8 years of age demonstrated that fractures of the zygomatic arch in this age group cannot be demonstrated by the typical submento-vertical view, but are shown on a Towne projection. The radiographic appearance of important maxillofacial fractures is demonstrated. The necessity of further studies in cases where reconstructive surgery appears necessary is discussed and CT rather then conventional tomography is advocated. (orig.) [de

Self-healing elastomer system

Science.gov (United States)

Keller, Michael W. (Inventor); Sottos, Nancy R. (Inventor); White, Scott R. (Inventor)

2009-01-01

A composite material includes an elastomer matrix, a set of first capsules containing a polymerizer, and a set of second capsules containing a corresponding activator for the polymerizer. The polymerizer may be a polymerizer for an elastomer. The composite material may be prepared by combining a first set of capsules containing a polymerizer, a second set of capsules containing a corresponding activator for the polymerizer, and a matrix precursor, and then solidifying the matrix precursor to form an elastomeric matrix.

Experimental testing on free vibration behaviour for silicone rubbers proposed within lumbar disc prosthesis

Energy Technology Data Exchange (ETDEWEB)

Rotaru, Iuliana, E-mail: rotaruiuliana2000@gmail.com [“Gheorghe Asachi” Technical University of Iasi, Faculty of Mechanical Engineering, Department of Mechanical Engineering, Mechatronics and Robotics, 61-63 Bd. Dimitrie Mangeron, 700050 Iasi (Romania); “Gr. T. Popa” University of Medicine and Pharmacy of Iasi, Faculty of Medical Bioengineering, Department of Biomedical Sciences, 9-13 M. Kogalniceanu Street, 700454 Iasi (Romania); Bujoreanu, Carmen [“Gheorghe Asachi” Technical University of Iasi, Faculty of Mechanical Engineering, Department of Mechanical Engineering, Mechatronics and Robotics, 61-63 Bd. Dimitrie Mangeron, 700050 Iasi (Romania); Bele, Adrian; Cazacu, Maria [“Petru Poni” Institute of Macromolecular Chemistry, Aleea Gr. Ghica Voda 41 A, 700487 Iasi (Romania); Olaru, Dumitru [“Gheorghe Asachi” Technical University of Iasi, Faculty of Mechanical Engineering, Department of Mechanical Engineering, Mechatronics and Robotics, 61-63 Bd. Dimitrie Mangeron, 700050 Iasi (Romania)

2014-09-01

This research was focused on the damping capacity study of two types of silicone rubbers proposed as layers within total lumbar disc prostheses of ball-and-socket model. In order to investigate the damping capacity, the two silicone rubber types mainly differing by the molecular mass of polymeric matrix and the filler content, as was emphasized by scanning electron microscopy and differential scanning calorimetry, were subjected to free vibration testing. Using an adapted experimental installation, three kinds of damping testing were realised: tests without samples and tests with three samples of each type of silicone rubber (69 ShA and 99 ShA). The free vibration tests were performed at a frequency of about 6 Hz using a weight of 11.8 kg. The relative damping coefficient was determined by measuring of two successive amplitudes on the vibrogram and calculating of the logarithmic decrement. The test results with silicone rubber samples showed a relative damping coefficient of 0.058 and respectively 0.077, whilst test results without samples showed a relative damping coefficient of 0.042. These silicone rubbers were found to have acceptable damping properties to be used as layers placed inside the prosthetic components. - Highlights: • Two types of silicone rubber were proposed within the total lumbar disc prostheses. • The filler content of elastomers was highlighted by microscopy investigation. • Damping capacity of the two elastomers was evaluated using free vibration analysis. • The logarithmic decrement and the relative damping coefficient were determined. • The silicone rubbers prepared in our work showed acceptable damping properties.

Experimental testing on free vibration behaviour for silicone rubbers proposed within lumbar disc prosthesis

International Nuclear Information System (INIS)

Rotaru, Iuliana; Bujoreanu, Carmen; Bele, Adrian; Cazacu, Maria; Olaru, Dumitru

2014-01-01

This research was focused on the damping capacity study of two types of silicone rubbers proposed as layers within total lumbar disc prostheses of ball-and-socket model. In order to investigate the damping capacity, the two silicone rubber types mainly differing by the molecular mass of polymeric matrix and the filler content, as was emphasized by scanning electron microscopy and differential scanning calorimetry, were subjected to free vibration testing. Using an adapted experimental installation, three kinds of damping testing were realised: tests without samples and tests with three samples of each type of silicone rubber (69 ShA and 99 ShA). The free vibration tests were performed at a frequency of about 6 Hz using a weight of 11.8 kg. The relative damping coefficient was determined by measuring of two successive amplitudes on the vibrogram and calculating of the logarithmic decrement. The test results with silicone rubber samples showed a relative damping coefficient of 0.058 and respectively 0.077, whilst test results without samples showed a relative damping coefficient of 0.042. These silicone rubbers were found to have acceptable damping properties to be used as layers placed inside the prosthetic components. - Highlights: • Two types of silicone rubber were proposed within the total lumbar disc prostheses. • The filler content of elastomers was highlighted by microscopy investigation. • Damping capacity of the two elastomers was evaluated using free vibration analysis. • The logarithmic decrement and the relative damping coefficient were determined. • The silicone rubbers prepared in our work showed acceptable damping properties

maxillofacial surgery

African Journals Online (AJOL)

The history of maxillofacial and oral injuries, including mandibular fractures, from 1650 BC to the present, is the topic of two publications.1,2 To summarise: the Greek. 'Father of Medicine' Hippocrates was the first to describe fracture treatment – he recommended bandages and single jaw fixation. Celsus, a Roman (30 BC ...

Toughening elastomers with sacrificial bonds and watching them break

NARCIS (Netherlands)

Ducrot, E.; Chen, Y.; Bulters, M.J.H.; Sijbesma, R.P.; Creton, C.

2014-01-01

Elastomers are widely used because of their large-strain reversible deformability. Most unfilled elastomers suffer from a poor mechanical strength, which limits their use. Using sacrificial bonds, we show how brittle, unfilled elastomers can be strongly reinforced in stiffness and toughness (up to 4

The Electrical Breakdown of Thin Dielectric Elastomers

DEFF Research Database (Denmark)

Zakaria, Shamsul Bin; Morshuis, Peter H. F.; Yahia, Benslimane Mohamed

2014-01-01

Dielectric elastomers are being developed for use in actuators, sensors and generators to be used in various applications, such as artificial eye lids, pressure sensors and human motion energy generators. In order to obtain maximum efficiency, the devices are operated at high electrical fields....... This increases the likelihood for electrical breakdown significantly. Hence, for many applications the performance of the dielectric elastomers is limited by this risk of failure, which is triggered by several factors. Amongst others thermal effects may strongly influence the electrical breakdown strength....... In this study, we model the electrothermal breakdown in thin PDMS based dielectric elastomers in order to evaluate the thermal mechanisms behind the electrical failures. The objective is to predict the operation range of PDMS based dielectric elastomers with respect to the temperature at given electric field...

Hencky's model for elastomer forming process

Science.gov (United States)

Oleinikov, A. A.; Oleinikov, A. I.

2016-08-01

In the numerical simulation of elastomer forming process, Henckys isotropic hyperelastic material model can guarantee relatively accurate prediction of strain range in terms of large deformations. It is shown, that this material model prolongate Hooke's law from the area of infinitesimal strains to the area of moderate ones. New representation of the fourth-order elasticity tensor for Hencky's hyperelastic isotropic material is obtained, it possesses both minor symmetries, and the major symmetry. Constitutive relations of considered model is implemented into MSC.Marc code. By calculating and fitting curves, the polyurethane elastomer material constants are selected. Simulation of equipment for elastomer sheet forming are considered.

Fresh frozen bone in oral and maxillofacial surgery

Directory of Open Access Journals (Sweden)

Luigi Fabrizio Rodella

2015-06-01

Full Text Available The aim of the current study was to review the use of fresh frozen bone (FFB in oral and maxillofacial surgery. We performed a review of the articles published in the literature between 1976 and May 2014 analyzing three medical databases (PubMed, Cochrane Library, and Embase and using specific search terms. Literature analysis on FFB applications in oral and maxillofacial surgery revealed 47 articles between 1976 and May 2014. There are 46 clinical articles and one review. Clinical articles are represented by 22 case reports and case series and 24 retrospective studies. Classifying the scientific production by year of publication, it is evident that especially during the last 6 years there was an increase of FFB graft use in oral and maxillofacial approaches. The literature analysis on FFB's use shows that its application in oral and maxillofacial surgery began slowly in 1992 with Perrott and since 2006 it had a real development. The recent significant increase emphasizes the importance of FFB for bone regeneration in oral and maxillofacial surgery. This review found consistent evidence of FFB's use increase in oral and maxillofacial surgery suggesting a valid instrument for bone regeneration. To date, risks connected to the infections' transmission and to the immunogenic potential are extremely low and could be considered practically absent. So, this is an important alternative in the preimplant reconstructive surgery.

Changes in mechanical properties and morphology of elastomer coatings after immersion in salt solutions

Science.gov (United States)

Terán Arce, Fernando; Avci, Recep; Beech, Iwona; Cooksey, Keith; Wigglesworth-Cooksey, Barbara

2004-03-01

RTV11 (^TM GE Silicones) and Intersleek (^TM International Paints) are two elastomers of considerable significance to the navy and maritime industry for their application as fouling release coatings. Both materials are composed of polymeric matrices with embedded filler particles, which provide increased strength and durability to the elastomer. Using Atomic force microscopy (AFM), surface and bulk analysis techniques, we have found surface regions with microelastic properties, which correlate with the locations of filler particles inside the coatings. These particles are able to undergo elastic displacements of hundreds of nm inside the polymeric matrix during compression by the AFM tip. While elastic properties of Intersleek remain largely unchanged after immersion in salt solutions, roughening, embrittlement and stiffening occurs in RTV11 coatings depending on the amount of curing agent and humidity used during preparation and curing, respectively. Interestingly, such transformations are absent after immersion in pure water. In particle free regions, elastic moduli of RTV11 take values of 2 - 3 MPa before immersion in salt solutions. After immersion, those values increase 5 - 10 times.

Skin-inspired hydrogel-elastomer hybrids with robust interfaces and functional microstructures

Science.gov (United States)

Yuk, Hyunwoo; Zhang, Teng; Parada, German Alberto; Liu, Xinyue; Zhao, Xuanhe

2016-06-01

Inspired by mammalian skins, soft hybrids integrating the merits of elastomers and hydrogels have potential applications in diverse areas including stretchable and bio-integrated electronics, microfluidics, tissue engineering, soft robotics and biomedical devices. However, existing hydrogel-elastomer hybrids have limitations such as weak interfacial bonding, low robustness and difficulties in patterning microstructures. Here, we report a simple yet versatile method to assemble hydrogels and elastomers into hybrids with extremely robust interfaces (interfacial toughness over 1,000 Jm-2) and functional microstructures such as microfluidic channels and electrical circuits. The proposed method is generally applicable to various types of tough hydrogels and diverse commonly used elastomers including polydimethylsiloxane Sylgard 184, polyurethane, latex, VHB and Ecoflex. We further demonstrate applications enabled by the robust and microstructured hydrogel-elastomer hybrids including anti-dehydration hydrogel-elastomer hybrids, stretchable and reactive hydrogel-elastomer microfluidics, and stretchable hydrogel circuit boards patterned on elastomer.

Soft hydrogels interpenetrating silicone – a polymer network for drug releasing medical devices

DEFF Research Database (Denmark)

Steffensen, Søren Langer; Merete H., Vestergaard,; Møller, Eva Horn

2016-01-01

such a sophisticated material by forming an interpenetrating polymer network (IPN) material through modification of silicone elastomers with a poly(2-hydroxyethyl methacrylate) (PHEMA)-based hydrogel. IPN materials with a PHEMA content in the range of 13%–38% (w/w) were synthesized by using carbon dioxide...

Role of Magnetorheological Fluids and Elastomers in Today’s World

Directory of Open Access Journals (Sweden)

Skalski Paweł

2017-12-01

Full Text Available This paper explains the role of magnetorheological fluids and elastomers in today’s world. A review of applications of magnetorheological fluids and elastomers in devices and machines is presented. Magnetorheological fluids and elastomers belong to the smart materials family. Properties of magnetorheological fluids and elastomers can be controlled by a magnetic field. Compared with magnetorheological fluids, magnetorheological elastomers overcome the problems accompanying applications of MR fluids, such as sedimentation, sealing issues and environmental contamination. Magnetorheological fluids and elastomers, due to their ability of dampening vibrations in the presence of a controlled magnetic field, have great potential present and future applications in transport. Magnetorheological fluids are used e.g. dampers, shock absorbers, clutches and brakes. Magnetorheological dampers and magnetorheological shock absorbers are applied e.g. in damping control, in the operation of buildings and bridges, as well as in damping of high-tension wires. In the automotive industry, new solutions involving magnetorheological elastomer are increasingly patented e.g. adaptive system of energy absorption, system of magnetically dissociable [hooks/detents/grips], an vibration reduction system of the car’s drive shaft. The application of magnetorheological elastomer in the aviation structure is presented as well.

Clinico-histopathologic types of maxillofacial malignancies with ...

African Journals Online (AJOL)

Clinico-histopathologic types of maxillofacial malignancies with emphasis on sarcomas: A 10-year review. ... Sarcomas peaked in the third decade with 70% occurring below the age of 40 years. The maxilla and the mandible were the most afflicted sites in the maxillofacial region accounting for 52%. The patients on average

Better fuel handling system performance through improved elastomers and seals

Energy Technology Data Exchange (ETDEWEB)

Wensel, R G; Metcalfe, R [Atomic Energy of Canada Ltd., Chalk River, ON (Canada)

1997-12-31

In the area of elastomers, tests have identified specific compounds that perform well in each class of CANDU service. They offer gains in service life, sometimes by factors of ten or more. Moreover, the aging characteristics of these specific compounds are being thoroughly investigated, whereas many elastomers used previously were either non-specific or their aging was unknown. In this paper the benefits of elastomer upgrading, as well as the deficiencies of current station elastomer practices, are discussed in the context of fuel handling equipment. Guidelines for procurement, storage, handling and condition monitoring of elastomer seals are outlined. (author). 3 figs.

Better fuel handling system performance through improved elastomers and seals

International Nuclear Information System (INIS)

Wensel, R.G.; Metcalfe, R.

1996-01-01

In the area of elastomers, tests have identified specific compounds that perform well in each class of CANDU service. They offer gains in service life, sometimes by factors of ten or more. Moreover, the aging characteristics of these specific compounds are being thoroughly investigated, whereas many elastomers used previously were either non-specific or their aging was unknown. In this paper the benefits of elastomer upgrading, as well as the deficiencies of current station elastomer practices, are discussed in the context of fuel handling equipment. Guidelines for procurement, storage, handling and condition monitoring of elastomer seals are outlined. (author). 3 figs

Maxillofacial prostheses challenges in resource constrained regions.

Science.gov (United States)

Tetteh, Sophia; Bibb, Richard J; Martin, Simon J

2017-10-24

This study reviewed the current state of maxillofacial rehabilitation in resource-limited nations. A rigorous literature review was undertaken using several technical and clinical databases using a variety of key words pertinent to maxillofacial prosthetic rehabilitation and resource-limited areas. In addition, interviews were conducted with researchers, clinicians and prosthetists that had direct experience of volunteering or working in resource-limited countries. Results from the review and interviews suggest rehabilitating patients in resource-limited countries remains challenging and efforts to improve the situation requires a multifactorial approach. In conclusion, public health awareness programmes to reduce the causation of injuries and bespoke maxillofacial prosthetics training programmes to suit these countries, as opposed to attempting to replicate Western training programmes. It is also possible that usage of locally sourced and cheaper materials and the use of low-cost technologies could greatly improve maxillofacial rehabilitation efforts in these localities. Implications for Rehabilitation More information and support needs to be provided to maxillofacial defect/injuries patients and to their families or guardians in a culturally sensitive manner by governments. The health needs, economic and psychological needs of the patients need to be taken into account during the rehabilitation process by clinicians and healthcare organizations. The possibility of developing training programs to suit these resource limited countries and not necessarily follow conventional fabrication methods must be looked into further by educational entities.

The influence of static pre-stretching on the mechanical ageing of filled silicone rubbers for dielectric elastomer applications

DEFF Research Database (Denmark)

Zakaria, Shamsul Bin; Yu, Liyun; Kofod, Guggi

2015-01-01

Dielectric elastomer (DE) pre-stretching is a key aspect of attaining better actuation performance, as ithelps prevent electromechanical instability (EMI) and usually lowers the Young’s modulus, thus leading toeasier deformation. The pre-stretched DE is not only susceptible to a high risk...

Magnetic and viscoelastic response of elastomers with hard magnetic filler

International Nuclear Information System (INIS)

Kramarenko, E Yu; Chertovich, A V; Semisalova, A S; Makarova, L A; Perov, N S; Khokhlov, A R; Stepanov, G V

2015-01-01

Magnetic elastomers (MEs) based on a silicone matrix and magnetically hard NdFeB particles have been synthesized and their magnetic and viscoelastic properties have been studied depending on the size and concentration of magnetic particles and the magnetizing field. It has been shown that magnetic particles can rotate in soft polymer matrix under applied magnetic field, this fact leading to some features in both magnetic and viscoelastic properties. In the maximum magnetic field used magnetization of MEs with smaller particles is larger while the coercivity is smaller due to higher mobility of the particles within the polymer matrix. Viscoelastic behavior is characterized by long relaxation times due to restructuring of the magnetic filler under the influence of an applied mechanical force and magnetic interactions. The storage and loss moduli of magnetically hard elastomers grow significantly with magnetizing field. The magnetic response of the magnetized samples depends on the mutual orientation of the external magnetic field and the internal sample magnetization. Due to the particle rotation within the polymer matrix, the loss factor increases abruptly when the magnetic field is turned on in the opposite direction to the sample magnetization, further decreasing with time. Moduli versus field dependences have minimum at non-zero field and are characterized by a high asymmetry with respect to the field direction. (paper)

[Cranio-maxillofacial traumatology

NARCIS (Netherlands)

Kroon, F.H.; Beek, G.J.; Damme, P.A. van

2007-01-01

During the last 50 years, significant developments have taken place in the treatment of cranio-maxillofacial fractures. The aim of treatment is to achieve the most complete possible restoration of facial functions Epidemiologic figures for these fractures are sparsely available in the literature,

Maxillofacial fractures sustained during baseball and softball.

Science.gov (United States)

Yamamoto, Kazuhiko; Murakami, Kazuhiro; Sugiura, Tsutomu; Ishida, Jun-ichi; Imai, Yuichiro; Fujimoto, Masaki; Kirita, Tadaaki

2009-04-01

The purpose of this study was to investigate the demographics, the type of impact, the site and the treatment of maxillofacial fractures sustained during baseball and softball to develop an effective preventive strategy. Data of 82 patients treated for baseball- and softball-related maxillofacial fractures at the Department of Oral and Maxillofacial Surgery, Nara Medical University between 1982 and 2007 were retrospectively analyzed. Injuries were found in 64 men in baseball and 16 men and two women in softball with average ages of 19.6 and 30.0 years, respectively. Fractures were caused by being hit by the ball in 61 patients followed by collision in 16 patients. Fractures of the mandible and the mid-face were found in 44 and 38 patients, respectively. The mental and angle region of the mandible and zygoma and alveolar bone of the maxilla were frequently involved. Treatment was mostly conservative. Open reduction and internal fixation were performed only in 15 patients. Most maxillofacial fractures in these sports were ball-related. Therefore, effective preventive means should be considered to protect against such injuries.

Effects of tritium in elastomers

International Nuclear Information System (INIS)

Zapp, P.E.

1982-01-01

Elastomers are used as flange gaskets in the piping system of the Savannah River Plant tritium facilities. A number of elastomers is being examined to identify those compounds more radiation-resistant than the currently specified Buna-N rubber and to study the mechanism of tritium radiation damage. Radiation resistance is evaluated by compression set tests on specimens exposed to about 1 atm tritium for several months. Initial results show that ethylene-propylene rubber and three fluoroelastomers are superior to Buna-N. Off-gassing measurements and autoradiography show that retained surface absorption of tritium varies by more than an order of magnitude among the different elastomer compounds. Therefore, tritium solubility and/or exchange may have a role in addition to that of chemical structure in the damage process. Ongoing studies of the mechanism of radiation damage include: (1) tritium absorption kinetics, (2) mass spectroscopy of radiolytic products, and (3) infrared spectroscopy

Multiple maxillofacial fractures in a patient undergoing orthodontic ...

African Journals Online (AJOL)

A multi-disciplinary team approach for the management of maxillofacial fractures in patients undergoing orthodontic treatment with fixed appliances is suggested. Orthodontic treatment with surgical involvement has been found to improve both facial aesthetics and occlusal function. Key words: Maxillofacial, trauma, ...

Phase Behavior of Three PBX Elastomers in High-Pressure Chlorodifluoromethane

Science.gov (United States)

Lee, Byung-Chul

2017-10-01

The phase equilibrium behavior data are presented for three kinds of commercial polymer-bonded explosive (PBX) elastomers in chlorodifluoromethane (HCFC22). Levapren^{{registered }} ethylene- co-vinyl acetate (LP-EVA), HyTemp^{{registered }} alkyl acrylate copolymer (HT-ACM), and Viton^{{registered }} fluoroelastomer (VT-FE) were used as the PBX elastomers. For each elastomer + HCFC22 system, the cloud point (CP) and/or bubble point (BP) pressures were measured while varying the temperature and elastomer composition using a phase equilibrium apparatus fitted with a variable-volume view cell. The elastomers examined in this study indicated a lower critical solution temperature phase behavior in the HCFC22 solvent. LP-EVA showed the CPs at temperatures of 323 K to 343 K and at pressures of 3 MPa to 10 MPa, whereas HT-ACM showed the CPs at conditions between 338 K and 363 K and between 4 MPa and 12 MPa. For the LP-EVA and HT-ACM elastomers, the BP behavior was observed at temperatures below about 323 K. For the VT-FE + HCFC22 system, only the CP behavior was observed at temperatures between 323 K and 353 K and at pressures between 6 MPa and 21 MPa. As the elastomer composition increased, the CP pressure increased, reached a maximum value at a specific elastomer composition, and then remained almost constant.

Processing a difficult urethane elastomer system

International Nuclear Information System (INIS)

Gillespie, T.J.

1977-01-01

A detailed study of an adiprene/butanediol/trimethylolpropane elastomer system and the associated production process was performed to assess the importance of various processing factors on the physical properties of the system. Results indicated that control of the curing cycle, material ratio, moisture in the curing agent and elastomer, mixing, and vacuum level was necessary. Sufficient control of the manual process could not be obtained to eliminate significant physical property variability. An automatic metering, mixing and dispensing machine was purchased for laboratory evaluation. After modification, including the addition of a high shear vacuum type mixer, and with close vacuum and temperature control, material property variability was still at an unacceptable level. A tracer agent was introduced into the curing agent system to assess the distribution of the curing agent in the elastomer. Machine evaluation using the tracer agent indicated that distribution of the curing agent in the elastomer was very poor is spite of the high shear mixing configuration. The addition of an oscillating motion to the mixing configuration. The addition of an oscillating motion to the mixing system significantly improved curing agent distribution and eliminated material property variability problems. 16 figures, 3 tables

PLA-based biodegradable and tunable soft elastomers for biomedical applications

International Nuclear Information System (INIS)

Harrane, Amine; Leroy, Adrien; Nouailhas, Hélène; Garric, Xavier; Coudane, Jean; Nottelet, Benjamin

2011-01-01

Although desirable for biomedical applications, soft degradable elastomers having balanced amphiphilic behaviour are rarely described in the literature. Indeed, mainly highly hydrophobic elastomers or very hydrophilic elastomers with hydrogel behaviours are found. In this work, we developed thermoset degradable elastomers based on the photo-cross-linking of poly(lactide)-poly(ethylene glycol)-poly(lactide) (PLA-PEG-PLA) triblock prepolymers. The originality of the proposed elastomers comes from the careful choice of the prepolymer amphiphilicity and from the possible modulation of their mechanical properties and degradation rates provided by cross-linkers of different nature. This is illustrated with the hydrophobic and rigid 2,4,6-triallyloxy-1,3,5-triazine compared to the hydrophilic and soft pentaerythritol triallyl ether. Thermal properties, mechanical properties, swelling behaviours, degradation rates and cytocompatibility have been evaluated. Results show that it is possible to generate a family of degradable elastomers covering a broad range of properties from a single biocompatible and biodegradable prepolymer.

Types and properties of elastomer materials used in CANDU reactor

Energy Technology Data Exchange (ETDEWEB)

You, Ho Sik; Jeong, Jin Kon [Korea Atomic Energy Research Institute, Daeduk (Korea, Republic of)

1996-05-01

Properties and kinds of elastomer materials used in a CANDU power plant have been described. The elastomer materials have been used as a sealing material in the components f nuclear power plant since they have many excellent properties that can not be seen in other materials. It is very important to select proper elastomer materials used in the nuclear power plant are required to have resistance to temperature as well as radiation. According to the experimental results performed at some laboratories including the Chalk River Laboratory of AECL, elastomer materials with high resistance to temperature and radiation are Nitrile, Ethylene, Propylene and Butyl. These materials have been used in a lot of components of Wolsong unit 1 and Wolsong 2, 3 and 4 which are under elastomer material. Therefore, the studies on the standardization are currently under way to limit about 10 different kinds of elastomer materials to be used in the plant. 16 tabs., 1 fig., 12 refs. (Author) .new.

Electrical Breakdown and Mechanical Ageing in Dielectric Elastomers

DEFF Research Database (Denmark)

Zakaria, Shamsul Bin

Dielectric elastomers (DE) are used in various applications, such as artificial eye lids, pressure sensors and human motion energy generators. For many applications, one of the major factors that limits the DE performance is premature electrical breakdown. There are many approaches that have been......, the lifetime of elastomer materials needs further investigation. Therefore, in the second strategy, several DE parameters such as Young’s moduli, breakdown strengths and dielectric permittivities of PDMS elastomers filled with hard filler particles were investigated after being subjected to pre...

Fluoridated elastomers: effect on the microbiology of plaque.

Science.gov (United States)

Benson, Philip E; Douglas, C W Ian; Martin, Michael V

2004-09-01

The objective of this study was to investigate the effect of fluoridated elastomeric ligatures on the microbiology of local dental plaque in vivo. This randomized, prospective, longitudinal, clinical trial had a split-mouth crossover design. The subjects were 30 patients at the beginning of their treatment with fixed orthodontic appliances in the orthodontic departments of the Liverpool and the Sheffield dental hospitals in the United Kingdom. The study consisted of 2 experimental periods of 6 weeks with a washout period between. Fluoridated elastomers were randomly allocated at the first visit to be placed around brackets on tooth numbers 12, 11, 33 or 22, 21, 43. Nonfluoridated elastomers were placed on the contralateral teeth. Standard nonantibacterial fluoridated toothpaste and mouthwash were supplied. After 6 weeks (visit 2), the elastomers were removed, placed in transport media, and plated on agar within 2 hours. Nonfluoridated elastomers were placed on all brackets for 1 visit to allow for a washout period. At visit 3, fluoridated elastomers were placed on the teeth contralateral to those that received them at visit 1. At visit 4, the procedures at visit 2 were repeated. Samples were collected on visits 2 and 4. A logistic regression was performed, with the presence or absence of streptococcal or anaerobic growth as the dependent variable. A mixed-effects analysis of variance was carried out with the percentage of streptococcal or anaerobic bacterial count as the dependent variable. The only significant independent variables were the subject variable (P =bacterial count and the visit variable for the percentage of streptococcal count (P =fluoridated or nonfluoridated elastomers was not significant for percentage of either streptococcal (P =.288) or anaerobic count (P =.230). Fluoridated elastomers are not effective at reducing local streptococcal or anaerobic bacterial growth after a clinically relevant time in the mouth.

Flexible and stretchable electrodes for dielectric elastomer actuators

Science.gov (United States)

Rosset, Samuel; Shea, Herbert R.

2013-02-01

Dielectric elastomer actuators (DEAs) are flexible lightweight actuators that can generate strains of over 100 %. They are used in applications ranging from haptic feedback (mm-sized devices), to cm-scale soft robots, to meter-long blimps. DEAs consist of an electrode-elastomer-electrode stack, placed on a frame. Applying a voltage between the electrodes electrostatically compresses the elastomer, which deforms in-plane or out-of plane depending on design. Since the electrodes are bonded to the elastomer, they must reliably sustain repeated very large deformations while remaining conductive, and without significantly adding to the stiffness of the soft elastomer. The electrodes are required for electrostatic actuation, but also enable resistive and capacitive sensing of the strain, leading to self-sensing actuators. This review compares the different technologies used to make compliant electrodes for DEAs in terms of: impact on DEA device performance (speed, efficiency, maximum strain), manufacturability, miniaturization, the integration of self-sensing and self-switching, and compatibility with low-voltage operation. While graphite and carbon black have been the most widely used technique in research environments, alternative methods are emerging which combine compliance, conduction at over 100 % strain with better conductivity and/or ease of patternability, including microfabrication-based approaches for compliant metal thin-films, metal-polymer nano-composites, nanoparticle implantation, and reel-to-reel production of μm-scale patterned thin films on elastomers. Such electrodes are key to miniaturization, low-voltage operation, and widespread commercialization of DEAs.

Smartphone photography in oral and maxillofacial surgery.

Science.gov (United States)

Jamil, F

2016-01-01

An increasing number of staff in oral and maxillofacial surgery (OMFS) departments take clinical photographs with their personal phones. We report the results of a survey on the use of smartphone photography in OMFS departments in the United Kingdom, and highlight the guidelines that govern their use and the associated ethical and medicolegal implications. Copyright © 2015 The British Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Perspectives of stem cell use in reconstructive maxillofacial surgery

Directory of Open Access Journals (Sweden)

Mikhail G. Semyonov

2016-12-01

Full Text Available The discovery of stem cells is one of the greatest achievements of molecular and cell biology, and associated research has confirmed the possibility of self-renewal and differentiation into specialized tissue stem cells. The use of cellular technologies is an important trend in modern medicine. The aim of this article is to briefly review current findings on the use of stem cells in cardiology, endocrinology, neurology, traumatology, and maxillofacial surgery. All data were retrieved from experimental and clinical studies using various cell technologies. The material is part of ongoing maxillofacial surgery research to investigate the possible use of stem cells in reconstructive maxillofacial surgery for jaw bone pathologies in children. Present tissue engineering methods provide some opportunities for solving difficult clinical problems in oral and maxillofacial surgery. Despite some international achievements of effective application of IC in various diseases, clinical use in reconstructive surgery requires further investigation.

Numerical simulation and experimental validation of the large deformation bending and folding behavior of magneto-active elastomer composites

International Nuclear Information System (INIS)

Sheridan, Robert; VonLockette, Paris R; Roche, Juan; Lofland, Samuel E

2014-01-01

This work seeks to provide a framework for the numerical simulation of magneto-active elastomer (MAE) composite structures for use in origami engineering applications. The emerging field of origami engineering employs folding techniques, an array of crease patterns traditionally on a single flat sheet of paper, to produce structures and devices that perform useful engineering operations. Effective means of numerical simulation offer an efficient way to optimize the crease patterns while coupling to the performance and behavior of the active material. The MAE materials used herein are comprised of nominally 30% v/v, 325 mesh barium hexafarrite particles embedded in Dow HS II silicone elastomer compound. These particulate composites are cured in a magnetic field to produce magneto-elastic solids with anisotropic magnetization, e.g. they have a preferred magnetic axis parallel to the curing axis. The deformed shape and/or blocked force characteristics of these MAEs are examined in three geometries: a monolithic cantilever as well as two- and four-segment composite accordion structures. In the accordion structures, patches of MAE material are bonded to a Gelest OE41 unfilled silicone elastomer substrate. Two methods of simulation, one using the Maxwell stress tensor applied as a traction boundary condition and another employing a minimum energy kinematic (MEK) model, are investigated. Both methods capture actuation due to magnetic torque mechanisms that dominate MAE behavior. Comparison with experimental data show good agreement with only a single adjustable parameter, either an effective constant magnetization of the MAE material in the finite element models (at small and moderate deformations) or an effective modulus in the minimum energy model. The four-segment finite element model was prone to numerical locking at large deformation. The effective magnetization and modulus values required are a fraction of the actual experimentally measured values which suggests a

fs- and ns-laser processing of polydimethylsiloxane (PDMS) elastomer: Comparative study

Energy Technology Data Exchange (ETDEWEB)

Stankova, N.E., E-mail: nestankova@yahoo.com [Institute of Electronics, Bulgarian Academy of Sciences, 72 Tsarigradsko Shose, Sofia 1784 (Bulgaria); Atanasov, P.A.; Nedyalkov, N.N.; Stoyanchov, T.R. [Institute of Electronics, Bulgarian Academy of Sciences, 72 Tsarigradsko Shose, Sofia 1784 (Bulgaria); Kolev, K.N.; Valova, E.I.; Georgieva, J.S.; Armyanov, St.A. [Rostislaw Kaischew Institute of Physical Chemistry, Bulgarian Academy of Sciences, Acad. G. Bonchev Str., Block 11, Sofia 1113 (Bulgaria); Amoruso, S.; Wang, X.; Bruzzese, R. [CNR-SPIN, Dipartimento di Scienze Fisiche, Universita degli Studi di Napoli Federico II, Complesso Universitario di Monte S. Angelo, Via Cintia, I-80126 Napoli (Italy); Grochowska, K.; Śliwiński, G. [Photophysics Department, The Szewalski Institute, Polish Academy of Sciences, 14 Fiszera St., 80-231 Gdańsk (Poland); Baert, K.; Hubin, A. [Vrije Universiteit Brussels, Faculty of Engineering, Research group, SURF “Electrochemical and Surface Engineering” (Belgium); Delplancke, M.P.; Dille, J. [Université Libre de Bruxelles, Materials Engineering, Characterization, Synthesis and Recycling (Service 4MAT), Faculté des Sciences Appliquées, 1050 Brussels (Belgium)

2015-05-01

Highlights: • fs- and ns-laser (266 and 532 nm) processing of PDMS-elastomer, in air, is studied. • High definition tracks (on the PDMS-elastomer surface) for electrodes are produced. • Selective Pt or Ni metallization of the tracks is produced via electroless plating. • Irradiated and metallized tracks are characterized by μ-Raman spectrometry and SEM. • DC resistance of Pt and Ni tracks is always between 0.5 and 15 Ω/mm. - Abstract: Medical grade polydimethylsiloxane (PDMS) elastomer is a widely used biomaterial as encapsulation and/or as substrate insulator carrier for long term neural implants because of its remarkable properties. Femtosecond (λ = 263 and 527 nm) and nanosecond (266 and 532 nm) laser processing of PDMS-elastomer surface, in air, is investigated. The influence of different processing parameters, including laser wavelength, pulse duration, fluence, scanning speed and overlapping of the subsequent pulses, on the surface activation and the surface morphology are studied. High definition tracks and electrodes are produced. Remarkable alterations of the chemical composition and structural morphology of the ablated traces are observed in comparison with the native material. Raman spectra illustrate well-defined dependence of the chemical composition on the laser fluence, pulse duration, number of pulses and wavelength. An extra peak about ∼512–518 cm{sup −1}, assigned to crystalline silicon, is observed after ns- or visible fs-laser processing of the surface. In all cases, the intensities of Si−O−Si symmetric stretching at 488 cm{sup −1}, Si−CH{sub 3} symmetric rocking at 685 cm{sup −1}, Si−C symmetric stretching at 709 cm{sup −1}, CH{sub 3} asymmetric rocking + Si−C asymmetric stretching at 787 cm{sup −1}, and CH{sub 3} symmetric rocking at 859 cm{sup −1}, modes strongly decrease. The laser processed areas are also analyzed by SEM and optical microscopy. Selective Pt or Ni metallization of the laser processed

Computed Tomography evaluation of maxillofacial injuries

Directory of Open Access Journals (Sweden)

V Natraj Prasad

2017-01-01

Full Text Available Background & Objectives: The maxillofacial region, a complex anatomical structure, can be evaluated by conventional (plain films, Tomography, Multidetector Computed Tomography, Three-Dimensional Computed Tomography, Orthopantomogram and Magnetic Resonance Imaging. The study was conducted with objective of describing various forms of maxillofacial injuries, imaging features of different types of maxillofacial fractures and the advantage of using Three- Dimensional Computed Tomography reconstructed image. Materials & Methods: A hospital based cross-sectional study was conducted among 50 patients during April 2014 to September 2016 using Toshiba Aquilion Prime 160 slice Multi Detector Computed Tomography scanner.Results: The maxillofacial fractures were significantly higher in male population (88% than female population (12 %. Road traffic accidents were the most common cause of injury others being physical assault and fall from height. It was most common in 31-40 years (26% and 21-30 (24% years age group. Maxillary sinus was the commonest fracture (36% followed by nasal bone and zygomatic bone (30%, mandible and orbital bones (28%. Soft tissue swelling was the commonest associated finding. Three dimensional images (3 D compared to the axial scans missed some fractures. However, the extension of the complex fracture lines and degree of displacement were more accurately assessed. Complex fractures found were Le fort (6% and naso-orbito-ethmoid (4% fractures.Conclusion: The proper evaluation of complex anatomy of the facial bones requires Multidetector Computed Tomography which offers excellent spatial resolution enabling multiplanar reformations and three dimensional reconstructions for enhanced diagnostic accuracy and surgical planning.

Hardness measurements of silicon rubber and polyurethane rubber cured by ionizing radiation

International Nuclear Information System (INIS)

Basfar, A.A.

1995-01-01

This work investigates the hardness of both silicon rubber and polyurethane rubber cured by ionizing radiation. Shore A Hardness is used to characterize the subject elastomers in relation to the crosslinking process. Various formulations of both materials have been investigated in order to achieve the optimum cure conditions desired. A small amount of the curing agent has been incorporated in some formulations in order to reduce the required dose to achieve full cure conditions. Silicon rubber has shown improvements in hardness as absorbed dose is increased, whereas hardness remained constant over a range of absorbed doses for polyurethane rubber

Patterning nonisometric origami in nematic elastomer sheets

Science.gov (United States)

Plucinsky, Paul; Kowalski, Benjamin A.; White, Timothy J.; Bhattacharya, Kaushik

Nematic elastomers dramatically change their shape in response to diverse stimuli including light and heat. In this paper, we provide a systematic framework for the design of complex three dimensional shapes through the actuation of heterogeneously patterned nematic elastomer sheets. These sheets are composed of \\textit{nonisometric origami} building blocks which, when appropriately linked together, can actuate into a diverse array of three dimensional faceted shapes. We demonstrate both theoretically and experimentally that: 1) the nonisometric origami building blocks actuate in the predicted manner, 2) the integration of multiple building blocks leads to complex multi-stable, yet predictable, shapes, 3) we can bias the actuation experimentally to obtain a desired complex shape amongst the multi-stable shapes. We then show that this experimentally realized functionality enables a rich possible design landscape for actuation using nematic elastomers. We highlight this landscape through theoretical examples, which utilize large arrays of these building blocks to realize a desired three dimensional origami shape. In combination, these results amount to an engineering design principle, which we hope will provide a template for the application of nematic elastomers to emerging technologies.

Characteristics of maxillofacial injuries resulting from road traffic accidents – a 5 year review of the case records from Department of Maxillofacial Surgery in Katowice, Poland

Directory of Open Access Journals (Sweden)

Drugacz Jan

2006-08-01

Full Text Available Abstract Background In spite of employing numerous devices improving the safety in motor vehicles, traffic accidents are still among the main reasons of maxillofacial injuries. The maxillofacial injuries remain the serious clinical problem because of the specificity of this anatomical region. The knowledge of etiologic factors and mechanisms of injuries can be helpful in a satisfactory trauma prevention. The aim of this study was to find out the incidence and the pattern of maxillofacial injuries resulting from traffic accidents in the patients treated in the Department of Maxillofacial Surgery (Silesian Medical Academy in Katowice, Poland from January 2001 to December 2005. Methods The material consisted of 1024 case records of patients with maxillofacial injuries treated in the Maxillofacial Surgery Department of Silesian Medical Academy. The detailed analysis was carried out on the case records of 198 patients in the age of 3 to 68 with maxillofacial injuries resulting from traffic accidents. On the basis of data from a history, examination on admission, consultations and radiological examinations, patients' age and gender, we obtained the information on a pattern of injury and detailed description of an accident (the date and the time of an accident, the role of the patient in an accident. Results The traffic accidents were the cause of 19,93% maxillofacial injuries in the analyzed period of time. Most of the patients had injuries to the soft tissues of the face (22,21%, followed by tooth and alveolar process injuries (20,71% and mandibular fractures (18,69%. All the types of injuries were more common in men than in women. The majority of the patients were car drivers followed by car passengers, pedestrians, cyclists and motor cyclists. The peak age of the patients was between 18 to 25 years. The prevalent number of accidents resulting in injuries to this region took place in spring, especially between noon and 4 PM. Conclusion Our results

Ultrasonography - A diagnostic modality for oral and maxillofacial diseases

Directory of Open Access Journals (Sweden)

Priya Shirish Joshi

2014-01-01

Full Text Available Background: Many diseases present themselves in oral and maxillofacial regions and various modalities may be applied for their diagnosis, including intraoral and panoramic radiography, ultrasonography (USG, computer tomography, magnetic resonance imaging, and nuclear medicine methods such as positron emission tomography. Of these modalities, USG is easy to-use for the detection of non-invasive and soft tissue related diseases in oral and maxillofacial regions. USG plays an important role in analyzing normal and abnormal structures. In particular, in oral and maxillofacial regions, the USG may be clinically applied to evaluate lymph nodes, subcutaneous, and oral cavity-related diseases. Aims: The aim was to correlate the findings of USG and histopathology for the diagnosis of oral and maxillofacial pathology and to evaluate whether USG can be used as an adjunct in diagnosing oral and maxillofacial pathology. Materials and Methods: A total of 10 clinically diagnosed patients with intraoral cancerous growths, swellings in maxillary and neck region were included in this study. Incision biopsy was obtained for confirming provisional clinical diagnosis. The selected cases were advised USG. All patients were then posted either for hemi-glossectomy, hemi-mandibulectomy, and partial maxillectomy with or without radical neck dissection. Statistical Analysis: Student′s t-test and coefficient of correlation was used to statistically analyze significant relationship of both the methods. Result: In all 10 cases, USG correlated well with histopathology findings, it could also delineate tumor extent and measure tumor thickness. Conclusion: USG is an excellent method for the diagnosis of soft tissue lesions and can be used as an adjunct in diagnosing oral and maxillofacial pathology.

Toughening elastomers with sacrificial bonds and watching them break.

Science.gov (United States)

Ducrot, Etienne; Chen, Yulan; Bulters, Markus; Sijbesma, Rint P; Creton, Costantino

2014-04-11

Elastomers are widely used because of their large-strain reversible deformability. Most unfilled elastomers suffer from a poor mechanical strength, which limits their use. Using sacrificial bonds, we show how brittle, unfilled elastomers can be strongly reinforced in stiffness and toughness (up to 4 megapascals and 9 kilojoules per square meter) by introducing a variable proportion of isotropically prestretched chains that can break and dissipate energy before the material fails. Chemoluminescent cross-linking molecules, which emit light as they break, map in real time where and when many of these internal bonds break ahead of a propagating crack. The simple methodology that we use to introduce sacrificial bonds, combined with the mapping of where bonds break, has the potential to stimulate the development of new classes of unfilled tough elastomers and better molecular models of the fracture of soft materials.

Disclosed dielectric and electromechanical properties of hydrogenated nitrile–butadiene dielectric elastomer

International Nuclear Information System (INIS)

Yang, Dan; Tian, Ming; Dong, Yingchao; Liu, Haoliang; Yu, Yingchun; Zhang, Liqun

2012-01-01

This paper presents a comprehensive study of the effects of acrylonitrile content, crosslink density and plasticization on the dielectric and electromechanical performances of hydrogenated nitrile–butadiene dielectric elastomer. It was found that by increasing the acrylonitrile content of hydrogenated nitrile–butadiene dielectric elastomer, the dielectric constant will be improved accompanied with a sharp decrease of electrical breakdown strength leading to a small actuated strain. At a fixed electric field, a high crosslink density increased the elastic modulus of dielectric elastomer, but it also enhanced the electrical breakdown strength leading to a high actuated strain. Adding a plasticizer into the dielectric elastomer decreased the dielectric constant and electrical breakdown strength slightly, but reduced the elastic modulus sharply, which was beneficial for obtaining a large strain at low electric field from the dielectric elastomer. The largest actuated strain of 22% at an electric field of 30 kV mm −1 without any prestrain was obtained. Moreover, the hydrogenated nitrile–butadiene dielectric actuator showed good history dependence. This proposed material has great potential to be an excellent dielectric elastomer. (paper)

Oral and maxillofacial radiology: The challenge of change

International Nuclear Information System (INIS)

Omami, Galal

2015-01-01

Oral and maxillofacial radiologists may teach, practice, and/or conduct research with regard to any aspect of radiology. They are also responsible for establishing guidelines for radiographic selection criteria, radiation safety, and quality assurance. Some oral and maxillofacial radiologists have joint appointments in medical radiology. This provides a collaborative working environment with medical radiologists, who generally are not conversant with the diagnostic imaging of the jaws

Oral and Maxillofacial Surgery: Why the double degree? | Oji ...

African Journals Online (AJOL)

The International Association of oral and maxillofacial Surgeons (IAOMS) is committed to quality patient care. The education of oral and maxillofacial surgeons has, however, been in constant evolution ever since the inception of this speciality; and this state of flux reflects the dynamic expansion of its scope. Oral surgery has ...

Role of prophylactic antiemetics in oral and maxillofacial surgery

International Nuclear Information System (INIS)

Hanif, S.; Warraich, R.A.; Khan, S.R.; Riaz, N.; Mehdi, A.J.

2014-01-01

To find out the occurrence of postoperative nausea and vomiting (PONY) in oral and maxillofacial surgery done under general anaesthesia and to evaluate the purpose of using prophylactic antiemetic drugs. Design: Observational study. Place and Duration of the Study: Oral and Maxillofacial Department, KEMU / Mayo Hospital Lahore, from September 20 II to June 2012. Method: The number of patients who were operated in oral and maxillofacial surgery ward irrespective of age and gender for this study were 240. Risk factors related with PONY including gender, anesthetic drug used, surgical procedure, approach' used, total time of surgery and postoperative use of opioids were investigated. A wait and watch scheme was followed in patients with complaint of PONY. Antiemetics to be given in those cases where more than 2 episodes of vomiting took place. Results: It was found out that only II patients experienced from nausea and vomiting in post operative period. A notable relation was seen between PONY and female population, total time of surgery, anesthetic drug, surgery of tumor and temporomandibular joint. The surgical approach and opioids in postoperative period for PONY were found to be insignificant. Conclusion: PONY is not a significant finding in oral and maxillofacial surgery. We find out that there is no logic for the use of prophylactic antiemetic drugs in maxillofacial surgery. (author)

Maxillofacial trauma: managing potentially dangerous and disfiguring complex injuries [digest].

Science.gov (United States)

Das, Devjani; Salazar, Lea; Zaurova, Milana

2017-04-22

Patients with maxillofacial trauma require a careful evaluation due to the anatomical proximity of the maxillofacial region to the head and neck. Facial injuries can range from soft-tissue lacerations and nondisplaced nasal fractures to severe, complex fractures, eye injuries, and possible brain injury. Though the Advanced Trauma Life Support (ATLS) guidelines provide a framework for the management of trauma patients, they do not provide a detailed reference for many subtle or complex facial injuries. This issue adds a more comprehensive and systematic approach to the secondary survey of the maxillofacial area and emergency department management of injuries to the face. In addition to an overall review of maxillofacial trauma pathophysiology, associated injuries, and physical examination, this review will also discuss relevant imaging, treatment, and disposition plans. [Points & Pearls is a digest of Emergency Medicine Practice].

Metal and elastomer seal tests for accelerator applications

International Nuclear Information System (INIS)

Welch, K.M.; McIntyre, G.T.; Tuozzolo, J.E.; Skelton, R.; Pate, D.J.; Gill, S.M.

1989-01-01

The vacuum system of the Alternating Gradient Synchrotron (AGS) at Brookhaven National Laboratory has more than a thousand metal vacuum seals. Also, numerous elastomer seals are used throughout the AGS to seal large beam component chambers. An accelerator upgrade program is being implemented to reduce the AGS operating pressure by x100 and improve the reliability of the vacuum system. This paper describes work in progress on metal and elastomer vacuum seals to help meet those two objectives. Tests are reported on the sealing properties of a variety of metal seals used on different sealing surfaces. Results are also given on reversible sorption properties of certain elastomers. 16 refs., 6 figs., 4 tabs

Contact and friction in systems with fibre reinforced elastomers

NARCIS (Netherlands)

Rodriguez Pareja, Natalia Valentina

2012-01-01

The tribological behaviour (contact and friction) of systems that include fibre reinforced elastomers is studied in this thesis. The elastomer composite is considered to behave as a viscoelastic anisotropic continuum material. In the defined tribo-system, the most influential friction mechanism is

Role of catalysis in sustainable production of synthetic elastomers

Indian Academy of Sciences (India)

productions, the impact of synthetic elastomer business cannot be overlooked. The need of ... Keywords. Elastomers; catalysis; tyres and automobiles; mechanism; manufacturing process. 1. ..... level fractional factorial design model was also developed to ..... Polybutadiene can be manufactured by a number of pro- cesses ...

Poly (ricinoleic acid) based novel thermosetting elastomer.

Science.gov (United States)

Ebata, Hiroki; Yasuda, Mayumi; Toshima, Kazunobu; Matsumura, Shuichi

2008-01-01

A novel bio-based thermosetting elastomer was prepared by the lipase-catalyzed polymerization of methyl ricinoleate with subsequent vulcanization. Some mechanical properties of the cured carbon black-filled polyricinoleate compounds were evaluated as a thermosetting elastomer. It was found that the carbon black-filled polyricinoleate compounds were readily cured by sulfur curatives to produce a thermosetting elastomer that formed a rubber-like sheet with a smooth and non-sticky surface. The curing behaviors and mechanical properties were dependent on both the molecular weight of the polyricinoleate and the amount of the sulfur curatives. Cured compounds consisting of polyricinoleate with a molecular weight of 100,800 showed good mechanical properties, such as a hardness of 48 A based on the durometer A measurements, a tensile strength at break of 6.91 MPa and an elongation at break of 350%.

The effect of organo-clay on the dielectric properties of silicone rubber

International Nuclear Information System (INIS)

Razzaghi-Kashani, M; Gharavi, N; Javadi, S

2008-01-01

Dielectric elastomers are highly deformable and fast response smart materials capable of actuation under electric fields. Among commercially available dielectric elastomers, silicone rubber can be compounded with different fillers in order to modify its electrical and mechanical properties. To study the effect of organically modified montmorillonite (OMMT) on the dielectric properties of silicone rubber, OMMT was added to this rubber at two levels, 2% and 5%, using two methods, low-shear and high-shear mixing. Composites were characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM). The XRD patterns showed different crystallite structures for silicate platelets in the rubber matrix as a result of the two different mixing methods. In low-shear mixing, the ordered crystallite structure of the clay remains almost unchanged, whereas in high-shear mixing it loses its ordered structure, leading to the disappearance of the diffraction peaks. SEM and AFM micrographs depicted better dispersion and more uniform distribution of the organo-clay under high-shear mixing compared to those obtained by low-shear mixing. The tensile properties also confirmed the different degree of dispersion of the nano-clay resulting from the two different methods of mixing. The dielectric properties of the composites were measured under AC electric fields, and the results were compared with reference silicone rubbers with no OMMT. It was shown that the order of organo-clay layers in the less dispersed structure of the clay imparts an additional ionic polarization and higher dielectric permittivity compared to the case where the clay layers are more dispersed and lost their order. The storage and loss dielectric constants of base silicone rubber increase when it is compounded with OMMT

Improved reliability, maintainability and safety through elastomer upgrading

International Nuclear Information System (INIS)

Wensel, R.; Wittich, K.C.

1995-01-01

Equipment in nuclear plants has historically contained whatever elastomer each component supplier traditionally used for corresponding non-nuclear service. The resulting proliferation of elastomer compounds, many of which are far from optimal for the service conditions (e.g., pressure, temperature, radiation, etc.), has multiplied the costs to provide station reliability, maintainability and safety. Cost-effective improvements are being achieved in CANDU plants by upgrading and standardizing on a handful of high performing elastomer compounds. These upgraded materials offer significant gains in service life over the materials they replace (often by factors of 2 or more). This rationalization of elastomer compounds also facilitates the EQ process for safety-related equipment. Detailed test data on aging is currently being generated for these specific elastomers, encompassing the conditions and media (air, water, oil) common in CANDU service. Two key elements characterize this testing. First, each result is specific to the compound used in the test, and second, it is specific to the tested failure mode (e.g., compression set, extrusion, fracture, etc.). Having fewer, but more thoroughly tested compounds, avoids the penalty (associated with poorly characterized materials) of having to replace parts prematurely because of conservatism, while maintaining safe, reliable service. This paper provides an overview of this approach covering: the benefits of compound rationalization; and the how and why of establishing relevant failure criteria; appropriate quality assurance to maintain EQ; procurement, storage and handling guidelines; and monitoring and predicting in-service degradation. (author)

Frequency and temperature dependence of high damping elastomers

International Nuclear Information System (INIS)

Kulak, R.F.; Hughes, T.H.

1993-01-01

High damping steel-laminated elastomeric seismic isolation bearings are one of the preferred devices for isolating large buildings and structures. In the US, the current reference design for the Advanced Liquid Metal Reactor (ALMR) uses laminated bearings for seismic isolation. These bearings are constructed from alternating layers of high damping rubber and steel plates. They are typically designed for shear strains between 50 and 100% and are expected to sustain two to three times these levels for beyond design basis loading conditions. Elastomeric bearings are currently designed to provide a system frequency between 0.4 and 0.8 Hz and expected to operate between -20 and 40 degrees Centigrade. To assure proper performance of isolation bearings, it is necessary to characterize the elastomer's response under expected variations of frequency and temperature. The dynamic response of the elastomer must be characterized within the frequency range that spans the bearing acceptance test frequency, which may be as low as 0.005 Hz, and the design frequency. Similarly, the variation in mechanical characteristics of the elastomer must be determined over the design temperature range, which is between -20 and 40 degrees Centigrade. This paper reports on (1) the capabilities of a testing facility at ANL for testing candidate elastomers, (2) the variation with frequency and temperature of the stiffness and damping of one candidate elastomer, and (3) the effect of these variations on bearing acceptance testing criteria and on the choice of bearing design values for stiffness and damping

Causes of maxillofacial patient mortality in a Nigerian tertiary hospital

African Journals Online (AJOL)

a Lecturer, Department of Oral and Maxillofacial Surgery, Faculty of Dentistry, Bayero University, Kano and Consultant, Oral and Maxillofacial Surgeon,. Aminu Kano Teaching Hospital, Kano, Nigeria ... craniofacial trauma and stage IV malignancies [2, 3, 4]. Intraoperative deaths may also occur from anesthetic and/.

Pattern of Assault-induced Oral and Maxillofacial Injuries in Ado ...

African Journals Online (AJOL)

The etiology of maxillofacial injuries varies from one country to another and even within the same country depending on the prevailing socioeconomic, cultural, and environmental factors.[1-4] Road traffic crashes (RTC), assaults, sports, falls occupational hazards are documented causes of oral and maxillofacial injuries.

Gunshot (Pellets injury to the maxillofacial complex: a case report

Directory of Open Access Journals (Sweden)

Kiran D.N

2014-06-01

Full Text Available Gunshot injuries are rather serious but uncommon type of trauma in India. A 45-year-old male was presented with gunshot (pellets embedded in the maxillofacial area for 22 years. There is no consensus in the literature whether to attempt their removal or leave them in situ. Our patient had no long-term sequela like infection, fistula formation, carcinogenesis or metal poisoning to date except for chill feeling on cold days. Management of this patient presented a dilemma in treatment in view of the effects of foreign bodies in the maxillofacial area. Key words: Maxillofacial injuries; Wounds, gunshot; Firearms

Giant, Voltage-Actuated Deformation of a Dielectric Elastomer under Dead Load

OpenAIRE

Huang, Jiangshui; Li, Tiefeng; Foo, Choon Chiang; Clarke, David R.; Zhu, Jian; Suo, Zhigang

2012-01-01

Far greater voltage-actuated deformation is achievable for a dielectric elastomer under equal-biaxial dead load than under rigid constraint usually employed. Areal strains of 488% are demonstrated. The dead load suppresses electric breakdown, enabling the elastomer to survive the snap-through electromechanical instability. The breakdown voltage is found to increase with the voltage ramp rate. A nonlinear model for viscoelastic dielectric elastomers is developed and shown to be consistent with...

Active vibration isolation platform on base of magnetorheological elastomers

Energy Technology Data Exchange (ETDEWEB)

Mikhailov, Valery P., E-mail: mikhailov@bmstu.ru; Bazinenkov, Alexey M.

2017-06-01

The article describes the active vibration isolation platform on base of magnetorheological (MR) elastomers. An active damper based on the MR elastomers can be used as an actuator of micro- or nanopositioning for a vibroinsulated object. The MR elastomers give such advantages for active control of vibration as large range of displacements (up to 1 mm), more efficient absorption of the vibration energy, possibility of active control of amplitude-frequency characteristics and positioning with millisecond response speed and nanometer running accuracy. The article presents the results of experimental studies of the most important active damper parameters. Those are starting current, transient time for stepping, transmission coefficient of the vibration displacement amplitude.

Suppression of electromechanical instability in fiber-reinforced dielectric elastomers

Directory of Open Access Journals (Sweden)

Rui Xiao

2016-03-01

Full Text Available The electromechanical instability of dielectric elastomers has been a major challenge for the application of this class of active materials. In this work, we demonstrate that dielectric elastomers filled with soft fiber can suppress the electromechanical instability and achieve large deformation. Specifically, we developed a constitutive model to describe the dielectric and mechanical behaviors of fiber-reinforced elastomers. The model was applied to study the influence of stiffness, nonlinearity properties and the distribution of fiber on the instability of dielectric membrane under an electric field. The results show that there exists an optimal fiber distribution condition to achieve the maximum deformation before failure.

Toughening elastomers with sacrificial bonds and watching them break

Science.gov (United States)

Creton, Costantino

2014-03-01

Most unfilled elastomers are relatively brittle, in particular when the average molecular weight between crosslinks is lower than the average molecular weight between entanglements. We created a new class of tough elastomers by introducing isotropically prestretched chains inside ordinary acrylic elastomers by successive swelling and polymerization steps. These new materials combine a high entanglement density with a densely crosslinked structure reaching elastic moduli of 4 MPa and fracture strength of 25 MPa. The highly prestretched chains are the minority in the material and can break in the bulk of the material before catastrophic failure occurs, increasing the toughness of the material by two orders of magnitude up to 5 kJ/m2. To investigate the details of the toughening mechanism we introduced specific sacrificial dioxetane bonds in the prestretched chains that emit light when they break. In uniaxial extension cyclic experiments, we checked that the light emission corresponded exactly and quantitatively to the energy dissipation in each cycle demonstrating that short chains break first and long chains later. We then watched crack propagation in notched samples and mapped spatially the location of bond breakage ahead of the crack tip before and during propagation. This new toughening mechanism for elastomers creates superentangled rubbers and is ideally suited to overcome the trade-off between toughness and stiffness of ordinary elastomers. We gratefully acknowledge funding from DSM Ahead

Patient satisfaction with maxillofacial prosthesis. Literature review.

Science.gov (United States)

Goiato, Marcelo Coelho; Pesqueira, Aldiéris Alves; Ramos da Silva, Cristina; Gennari Filho, Humberto; Micheline Dos Santos, Daniela

2009-02-01

Obturators and facial prostheses are important not only in rehabilitation and aesthetics, but also in patient re-socialisation. The level of reintegration is directly related to the degree of satisfaction with rehabilitation. So, the maxillofacial prosthetics must provide patient satisfaction during treatment. This study aimed to search information in database and conduct a literature review on patient satisfaction with maxillofacial prosthesis. The problems experienced by these patients may decrease when specialists keep the patient on regular inspection. Rehabilitation through alloplasty or prosthetic restoration provides satisfactory conditions in aesthetics and well-being and reinstates individuals in familial and social environment.

An insight into the future beckons of maxillofacial prosthodontics: Anaplastology

Directory of Open Access Journals (Sweden)

S Padmaja

2015-01-01

Full Text Available It is the god given right of every human being to appear human. Few areas of dentistry offer more challenges to the technical skills or greater satisfaction for the successful rehabilitation of function and esthetics in the patient with gross anatomic defects and deformities of the maxillofacial region. Although remarkable advances in the surgical management of oral and facial defects, but cannot be satisfactorily repaired by plastic surgery alone. Hence, the demand for maxillofacial prosthetic devices for the rehabilitation of patients with congenital or acquired defects has intensified in recent years. This paper gives an insight into the latest innovations and improvisations in the field of maxillofacial prosthodontics.

Theory Of Dewetting In A Filled Elastomer Under Stress

Science.gov (United States)

Peng, Steven T. J.

1993-01-01

Report presents theoretical study of dewetting between elastomeric binder and filler particles of highly filled elastomer under multiaxial tension and resulting dilatation of elastomer. Study directed toward understanding and predicting nonlinear stress-vs.-strain behavior of filled elastomeric rocket propellant, also applicable to rubber in highly loaded tire or in damping pad.

Numerical analysis of laminated elastomer by FEM

International Nuclear Information System (INIS)

Mazda, T.; Shiojiri, H.

1993-01-01

A Computer code based on mixed finite element method was developed for three dimensional large strain analyses of laminated elastomers including nonlinear bulk stress vs. bulk strain relationships. The adopted element is the variable node element with maximum node numbers of 27 for displacements and 4 for pressures. At first, the displacements and pressures were calculated by the code using single element under various loading conditions. The results were compared with theoretical solutions and the both results' exactly coincided with each other. Next, the analyses of laminated elastomers subjected to axial loadings were conducted using both the new code and ABAQUS code, and the results were compared with the test results. The agreement of the results of the present code were better than ABAQUS code mainly due to the capability of handling wider range of material properties. Lastly, the shearing tests of laminated elastomers were simulated by the new code. The results were shown to be in good agreement with the test results. (author)

A small biomimetic quadruped robot driven by multistacked dielectric elastomer actuators

Science.gov (United States)

Nguyen, Canh Toan; Phung, Hoa; Dat Nguyen, Tien; Lee, Choonghan; Kim, Uikyum; Lee, Donghyouk; Moon, Hyungpil; Koo, Jachoon; Nam, Jae-do; Ryeol Choi, Hyouk

2014-06-01

A kind of dielectric elastomer (DE) material, called ‘synthetic elastomer’, has been developed based on acrylonitrile butadiene rubber (NBR) to be used as a dielectric elastomer actuator (DEA). By stacking single layers of synthetic elastomer, a linear actuator, called a multistacked actuator, is produced, and used by mechatronic and robotic systems to generate linear motion. In this paper, we demonstrate the application of the multistacked dielectric elastomer actuator in a biomimetic legged robot. A miniature robot driven by a biomimetic actuation system with four 2-DOF (two-degree-of-freedom) legged mechanisms is realized. Based on the experimental results, we evaluate the performance of the proposed robot and validate the feasibility of the multistacked actuator in a locomotion system as a replacement for conventional actuators.

A small biomimetic quadruped robot driven by multistacked dielectric elastomer actuators

International Nuclear Information System (INIS)

Nguyen, Canh Toan; Phung, Hoa; Nguyen, Tien Dat; Lee, Choonghan; Kim, Uikyum; Lee, Donghyouk; Moon, Hyungpil; Koo, Jachoon; Choi, Hyouk Ryeol; Nam, Jae-do

2014-01-01

A kind of dielectric elastomer (DE) material, called ‘synthetic elastomer’, has been developed based on acrylonitrile butadiene rubber (NBR) to be used as a dielectric elastomer actuator (DEA). By stacking single layers of synthetic elastomer, a linear actuator, called a multistacked actuator, is produced, and used by mechatronic and robotic systems to generate linear motion. In this paper, we demonstrate the application of the multistacked dielectric elastomer actuator in a biomimetic legged robot. A miniature robot driven by a biomimetic actuation system with four 2-DOF (two-degree-of-freedom) legged mechanisms is realized. Based on the experimental results, we evaluate the performance of the proposed robot and validate the feasibility of the multistacked actuator in a locomotion system as a replacement for conventional actuators. (paper)

Fracture studies of poly(propylene)/elastomer blend with β-form nucleating agent

International Nuclear Information System (INIS)

Bai Hongwei; Wang Yong; Zhang Danli; Xiao Chengquan; Song Bo; Li Yanli; Han Liang

2009-01-01

Poly(propylene)/elastomer blends with β-form nucleating agent (β-NA) aryl amides compound (TMB-5) were prepared. The effects of β-NA on crystallization, melting behaviors and elastomer morphologies of PP/elastomer blends were studied through polarization optical microscope (POM), differential scanning calorimetry (DSC) and scanning electronic microscope (SEM). The fracture behaviors, including notched Izod impact fracture and single-edge notched tensile (SENT) fracture, were comparatively studied to establish the role of NA in improving the fracture toughness of PP/elastomer blends. Our results showed that the presence of β-NA leads to determinable β-PP formation in the blends, and as a consequence the fracture toughness of the blend is improved dramatically. Compared with notched Izod impact testing, which can efficiently characterize the fracture toughness of the blends only at lower elastomer content, SENT testing provides more detail of fracture behavior in all the compositions. Furthermore, SENT test shows that the significant improvement in fracture toughness of PP/elastomer/β-NA is contributed to the simultaneous enhancement of crack initiation energy and crack propagation energy, but largely dominated by crack propagation stage.

Maxillofacial trauma in Tamil Nadu children and adolescents: A retrospective study

Directory of Open Access Journals (Sweden)

Ramraj Jayabalan Arvind

2013-01-01

Full Text Available Aim: The aim of this retrospective study is to describe the incidence, aetiology, complexity and surgical indications of maxillofacial injuries in children and adolescents population of Tamil Nadu state of india during period of 4 years. Materials and Methods: A retrospective review was conducted among 500 children and adolescents patients of age group 6 years to 16 years suffered or suffering with maxillofacial and skull fractures presenting to ten Level I trauma centers over a 4 year period.The data collected for this study included age, gender, etiology, associated maxillofacial trauma, anatomic site of fracture and treatment. Results and Conclusion: In our study the most common cause of trauma was traffic 35%, followed by falls 24% and sports 22%. Mandible was commenest bone prone to fracture, followed by maxilla and nasal bone. Mandible fractures accounted for 72% of all maxillofacial fractures.

Regenerative nanotechnology in oral and maxillofacial surgery.

Science.gov (United States)

Shakib, Kaveh; Tan, Aaron; Soskic, Vukic; Seifalian, Alexander M

2014-12-01

Regenerative nanotechnology is at the forefront of medical research, and translational medicine is a challenge to both scientists and clinicians. Although there has been an exponential rise in the volume of research generated about it for both medical and surgical uses, key questions remain about its actual benefits. Nevertheless, some people think that therapeutics based on its principles may form the core of applied research for the future. Here we give an account of its current use in oral and maxillofacial surgery, and implications and challenges for the future. Copyright © 2014 The British Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Obtaining consent to oral and maxillofacial surgery.

Science.gov (United States)

Poswillo, D

1989-09-01

The question of whether or not a patient has consented to treatment has recently become significant to all who practise oral and maxillofacial surgery. It is often linked to professional negligence when the outcome differs from the patient's perception or expectation of the operation. Consent may be oral or written, applies to referred patients and all those with physical and mental handicap and religious restrictions. Examples of procedure in discussing consent assist the surgeon to inform without creating fear. Knowledge of the benefits of informed consent and current legal opinion assist the oral and maxillofacial surgeon to avoid the pitfalls of failure to inform.

Subsequent publication of oral and maxillofacial surgery meeting abstracts.

Science.gov (United States)

Rodriguez, Joseph L; Laskin, Daniel M

2012-05-01

Previous studies in various medical specialties have shown that fewer than 50% of abstracts presented at meetings are subsequently published. The purpose of the present study was to determine the publication rate of abstracts presented at the annual meetings of the American Association of Oral and Maxillofacial Surgeons. The titles and authors of the abstracts from all oral abstract session presentations and posters by American contributors were collected from the Final Programs of the American Association of Oral and Maxillofacial Surgeons annual meetings for 2006 to 2009. A PubMed search for published articles through December 2010 was then performed using the authors' names, abstract titles, and key words. A total of 311 abstract presentations were done at the 4 annual meetings. Of these, only 85 (24%) were subsequently published. No difference was found between abstracts from oral or poster presentations. Most of the articles were published in the Journal of Oral and Maxillofacial Surgery. Because of deficiencies that can occur in abstracts and the need to disseminate the information they contain, it is important to take the appropriate measures to ensure that full articles are subsequently published. Copyright © 2012 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

Oral and maxillofacial surgery with computer-assisted navigation system.

Science.gov (United States)

Kawachi, Homare; Kawachi, Yasuyuki; Ikeda, Chihaya; Takagi, Ryo; Katakura, Akira; Shibahara, Takahiko

2010-01-01

Intraoperative computer-assisted navigation has gained acceptance in maxillofacial surgery with applications in an increasing number of indications. We adapted a commercially available wireless passive marker system which allows calibration and tracking of virtually every instrument in maxillofacial surgery. Virtual computer-generated anatomical structures are displayed intraoperatively in a semi-immersive head-up display. Continuous observation of the operating field facilitated by computer assistance enables surgical navigation in accordance with the physician's preoperative plans. This case report documents the potential for augmented visualization concepts in surgical resection of tumors in the oral and maxillofacial region. We report a case of T3N2bM0 carcinoma of the maxillary gingival which was surgically resected with the assistance of the Stryker Navigation Cart System. This system was found to be useful in assisting preoperative planning and intraoperative monitoring.

Submental Intubation in Patients with Complex Maxillofacial Injuries

Science.gov (United States)

Cheong, Yuseon; Kang, Seong Sik; Kim, Minsoo; Son, Hee Jeong; Park, Jaewoo; Kim, Jeong-Mo

2016-01-01

Airway management in patients with complex maxillofacial injuries is a challenge to anesthesiologists. Submental intubation is a useful technique that is less invasive than tracheostomy in securing the airways where orotracheal and nasotracheal intubation cannot be performed. This procedure avoids the use of tracheostomy and bypasses its associated morbidities. A flexible and kink-resistant reinforced endotracheal tube with detachable universal connector is commonly used for submental intubation. Herein, we report cases involving submental intubation using a reinforced endotracheal tube with a non-detachable universal connector in patients with complex maxillofacial injuries. PMID:27924286

Electromechanical performance analysis of inflated dielectric elastomer membrane for micro pump applications

Science.gov (United States)

Saini, Abhishek; Ahmad, Dilshad; Patra, Karali

2016-04-01

Dielectric elastomers have received a great deal of attention recently as potential materials for many new types of sensors, actuators and future energy generators. When subjected to high electric field, dielectric elastomer membrane sandwiched between compliant electrodes undergoes large deformation with a fast response speed. Moreover, dielectric elastomers have high specific energy density, toughness, flexibility and shape processability. Therefore, dielectric elastomer membranes have gained importance to be applied as micro pumps for microfluidics and biomedical applications. This work intends to extend the electromechanical performance analysis of inflated dielectric elastomer membranes to be applied as micro pumps. Mechanical burst test and cyclic tests were performed to investigate the mechanical breakdown and hysteresis loss of the dielectric membrane, respectively. Varying high electric field was applied on the inflated membrane under different static pressure to determine the electromechanical behavior and nonplanar actuation of the membrane. These tests were repeated for membranes with different pre-stretch values. Results show that pre-stretching improves the electromechanical performance of the inflated membrane. The present work will help to select suitable parameters for designing micro pumps using dielectric elastomer membrane. However this material lacks durability in operation.This issue also needs to be investigated further for realizing practical micro pumps.

Influence of gamma irradiation in the thermoplastic elastomer (TPE)

International Nuclear Information System (INIS)

Oliveira, Camila B.; Parra, Duclerc F.; Marchini, Leonardo G.

2017-01-01

The TPE is the nomenclature used for the thermoplastic elastomer, which is also known as thermoplastic rubber. It belongs to an under-researched class of engineering plastics, however, in recent years there has been steady growth due to its important and unusual combination of properties. During its use, it behaves like an elastomer, but, unlike traditional elastomers (vulcanized rubbers), it can be processed using conventional technologies and equipment used for thermoplastics, such as extrusion and injection. The processing of polymers, such as TPE by means of radiation, constitutes a technological area dedicated to the study of the physical and chemical effects caused by high energy radiation, such as gamma radiation. Thus the objective of this work is to evaluate the mechanical and thermal properties of TPE irradiated by 60 Co source of gamma radiation in different doses. The thermoplastic elastomer being modified by means of ionizing radiation at doses of 5, 10, 20, 30, 50 and 100 kGy the effects of the radiation on the mechanical and thermal properties of this material are evaluated through the tests of tensile tests, TGA, FTIR and Fluency Index

Conductive Elastomers for Stretchable Electronics, Sensors and Energy Harvesters

Directory of Open Access Journals (Sweden)

Jin-Seo Noh

2016-04-01

Full Text Available There have been a wide variety of efforts to develop conductive elastomers that satisfy both mechanical stretchability and electrical conductivity, as a response to growing demands on stretchable and wearable devices. This article reviews the important progress in conductive elastomers made in three application fields of stretchable technology: stretchable electronics, stretchable sensors, and stretchable energy harvesters. Diverse combinations of insulating elastomers and non-stretchable conductive materials have been studied to realize optimal conductive elastomers. It is noted that similar material combinations and similar structures have often been employed in different fields of application. In terms of stretchability, cyclic operation, and overall performance, fields such as stretchable conductors and stretchable strain/pressure sensors have achieved great advancement, whereas other fields like stretchable memories and stretchable thermoelectric energy harvesting are in their infancy. It is worth mentioning that there are still obstacles to overcome for the further progress of stretchable technology in the respective fields, which include the simplification of material combination and device structure, securement of reproducibility and reliability, and the establishment of easy fabrication techniques. Through this review article, both the progress and obstacles associated with the respective stretchable technologies will be understood more clearly.

Non-silicon substrate bonding mediated by poly(dimethylsiloxane) interfacial coating

Energy Technology Data Exchange (ETDEWEB)

Zhang, Hainan [Department of BioNano Technology, Gachon University, Gyeonggi-do 461-701 (Korea, Republic of); Lee, Nae Yoon, E-mail: nylee@gachon.ac.kr [Department of BioNano Technology, Gachon University, Gyeonggi-do 461-701 (Korea, Republic of); Gachon Medical Research Institute, Gil Medical Center, Inchon 405-760 (Korea, Republic of)

2015-02-01

Graphical abstract: Low-molecular-weight PDMS coating on the surfaces of non-silicon substrates such as thermoplastics ensures permanent sealing with a silicone elastomer, PDMS, simply by surface oxidization followed by ambient condition bonding, mediated by a robust siloxane bond formation at the interface. - Highlights: • Non-silicon thermoplastic was bonded with poly(dimethylsiloxane) silicone elastomer. • Low-molecular-weight PDMS interfacial layer was chemically coated on thermoplastic. • Bonding was realized by corona treatment and physical contact under ambient condition. • Bonding is universally applicable regardless of thermoplastic type and property. • Homogeneous PDMS-like microchannel was obtained inside the thermoplastic-PDMS microdevice. - Abstract: In this paper, we introduce a simple and robust strategy for bonding poly(dimethylsiloxane) (PDMS) with various thermoplastic substrates to fabricate a thermoplastic-based closed microfluidic device and examine the feasibility of using the proposed method for realizing plastic–plastic bonding. The proposed bonding strategy was realized by first coating amine functionality on an oxidized thermoplastic surface. Next, the amine-functionalized surface was reacted with a monolayer of low-molecular-weight PDMS, terminated with epoxy functionality, by forming a robust amine-epoxy bond. Both the PDMS-coated thermoplastic and PDMS were then oxidized and permanently assembled at 25 °C under a pressure of 0.1 MPa for 15 min, resulting in PDMS-like surfaces on all four inner walls of the microchannel. Surface characterizations were conducted, including water contact angle measurement, X-ray photoelectron spectroscopy (XPS), and fluorescence measurement, to confirm the successful coating of the thin PDMS layer on the plastic surface, and the bond strength was analyzed by conducting a peel test, burst test, and leakage test. Using the proposed method, we could successfully bond various thermoplastics such

Upgrading elastomer seals for nuclear service

Energy Technology Data Exchange (ETDEWEB)

Wittich, K C; Wensel, R; LaRose, R; Kuran, S

1995-06-01

Pumps, valves and instruments in nuclear plants have historically contained whatever elastomer each equipment supplier traditionally used for corresponding non-nuclear service. The proliferation of elastomer compounds, and their sometimes uncertain reliability, is now being reduced by upgrading and standardizing on a handful of compounds that have each been verified to be high performers for their class of service conditions. The objective is to make cost-effective improvements in the reliability and integrity of equipment in Canadian-designed nuclear plants. The effort focuses on elastomer seals and includes: understanding sealing fundamentals, developing relevant data for superior compounds for each service, and improving quality assurance methods, including handling and inspection guidelines. In practice, discussions with plant personnel and review of plant records are the first step. Two severe-service examples are given where these needs have been met by the following progression of activities: inspecting and laboratory testing of seals removed from service, preliminary and qualification testing of improvements, introduction into service, and monitoring the upgraded seals during phase-in periods. Large gains in reliability and integrity have been demonstrated for simulated normal and accident service conditions of heat, radiation and other deteriorative influences. Significant savings in maintenance costs are also projected. (author). 2 refs., 6 figs.

Upgrading elastomer seals for nuclear service

International Nuclear Information System (INIS)

Wittich, K.C.; Wensel, R.; LaRose, R.; Kuran, S.

1995-06-01

Pumps, valves and instruments in nuclear plants have historically contained whatever elastomer each equipment supplier traditionally used for corresponding non-nuclear service. The proliferation of elastomer compounds, and their sometimes uncertain reliability, is now being reduced by upgrading and standardizing on a handful of compounds that have each been verified to be high performers for their class of service conditions. The objective is to make cost-effective improvements in the reliability and integrity of equipment in Canadian-designed nuclear plants. The effort focuses on elastomer seals and includes: understanding sealing fundamentals, developing relevant data for superior compounds for each service, and improving quality assurance methods, including handling and inspection guidelines. In practice, discussions with plant personnel and review of plant records are the first step. Two severe-service examples are given where these needs have been met by the following progression of activities: inspecting and laboratory testing of seals removed from service, preliminary and qualification testing of improvements, introduction into service, and monitoring the upgraded seals during phase-in periods. Large gains in reliability and integrity have been demonstrated for simulated normal and accident service conditions of heat, radiation and other deteriorative influences. Significant savings in maintenance costs are also projected. (author). 2 refs., 6 figs

Upgrading elastomer seals for nuclear service

International Nuclear Information System (INIS)

Wittich, K.C.; Wensel, R.; Larose, R.; Kuran, S.

1998-01-01

Pumps, valves and instruments in nuclear plants have historically contained whatever elastomer each equipment supplier traditionally used for corresponding non-nuclear service. The proliferation of elastomer compounds, and their sometimes uncertain reliability, is now being reduced by upgrading and standardizing on a handful of compounds that have each been verified to be high performers for their class of service conditions. The objective is to make cost-effective improvements in the reliability and integrity of equipment in Canadian-designed nuclear plants. The effort focuses on elastomer seals and includes: understanding sealing fundamentals, developing relevant data for superior compounds for each service, and improving quality assurance methods, including handling and inspection guidelines. In practice, discussion with plant personnel and review of plant records are the first step. Two severe-service examples are given where these needs have been met by the following progression of activities: inspecting and laboratory testing of seals removed from service, preliminary and qualification testing of improvements, introduction into service, and monitoring the upgraded seals during phase-in periods. Large gains in reliability and integrity have been demonstrated for simulated normal and accident service conditions of heat, radiation and other deteriorative influences. Significant savings in maintenance costs are also projected. (author)

Application of Additive Manufacturing in Oral and Maxillofacial Surgery.

Science.gov (United States)

Farré-Guasch, Elisabet; Wolff, Jan; Helder, Marco N; Schulten, Engelbert A J M; Forouzanfar, Tim; Klein-Nulend, Jenneke

2015-12-01

Additive manufacturing is the process of joining materials to create objects from digital 3-dimensional (3D) model data, which is a promising technology in oral and maxillofacial surgery. The management of lost craniofacial tissues owing to congenital abnormalities, trauma, or cancer treatment poses a challenge to oral and maxillofacial surgeons. Many strategies have been proposed for the management of such defects, but autogenous bone grafts remain the gold standard for reconstructive bone surgery. Nevertheless, cell-based treatments using adipose stem cells combined with osteoconductive biomaterials or scaffolds have become a promising alternative to autogenous bone grafts. Such treatment protocols often require customized 3D scaffolds that fulfill functional and esthetic requirements, provide adequate blood supply, and meet the load-bearing requirements of the head. Currently, such customized 3D scaffolds are being manufactured using additive manufacturing technology. In this review, 2 of the current and emerging modalities for reconstruction of oral and maxillofacial bone defects are highlighted and discussed, namely human maxillary sinus floor elevation as a valid model to test bone tissue-engineering approaches enabling the application of 1-step surgical procedures and seeding of Good Manufacturing Practice-level adipose stem cells on computer-aided manufactured scaffolds to reconstruct large bone defects in a 2-step surgical procedure, in which cells are expanded ex vivo and seeded on resorbable scaffolds before implantation. Furthermore, imaging-guided tissue-engineering technologies to predetermine the surgical location and to facilitate the manufacturing of custom-made implants that meet the specific patient's demands are discussed. The potential of tissue-engineered constructs designed for the repair of large oral and maxillofacial bone defects in load-bearing situations in a 1-step surgical procedure combining these 2 innovative approaches is

Reasonable application of antibiotic prophylaxis in maxillofacial trauma: Literature review

Directory of Open Access Journals (Sweden)

Afshin Yadegari Naeeni

2016-07-01

Full Text Available Background and Aims: Despite advances in trauma management, treatment of the consequent infections has remained a major challenge. Antibiotic prophylaxis has been widely applied to reduce such infections. Although bacteria are present in most body parts, severe infections after treatment are less frequent in the head and neck of healthy individuals. The aim of the present study was to review the reasonable application of antibiotic prophylaxis in maxillofacial trauma. Materials and Methods: In this review article, PubMed and Google Scholar databases were searched for studies on antibiotic prophylaxis in maxillofacial trauma published during 2000-2014. Conclusion: Antibiotics were not prescribed for tears and small clean wounds in the face and mouth. However, prophylaxis was applied for extensive mouth injuries which involved the facial skin. In case of maxillofacial fractures, 24-hour administration of antibiotics sufficed for compound fractures of the mandible and other parts of the face. Antibiotics were not required in other types of fractures. Prophylaxis should be applied over short pre- or post-operative periods based on the severity and complexity of maxillofacial fractures and their relations with intra- and extraoral environments. Apparently, more detailed studies are warranted to further clarify the subject.

Optimization of large-scale fabrication of dielectric elastomer transducers

DEFF Research Database (Denmark)

Hassouneh, Suzan Sager

Dielectric elastomers (DEs) have gained substantial ground in many different applications, such as wave energy harvesting, valves and loudspeakers. For DE technology to be commercially viable, it is necessary that any large-scale production operation is nondestructive, efficient and cheap. Danfoss......-strength laminates to perform as monolithic elements. For the front-to-back and front-to-front configurations, conductive elastomers were utilised. One approach involved adding the cheap and conductive filler, exfoliated graphite (EG) to a PDMS matrix to increase dielectric permittivity. The results showed that even...... as conductive adhesives were rejected. Dielectric properties below the percolation threshold were subsequently investigated, in order to conclude the study. In order to avoid destroying the network structure, carbon nanotubes (CNTs) were used as fillers during the preparation of the conductive elastomers...

75 FR 39664 - Grant of Authority For Subzone Status Materials Science Technology, Inc. (Specialty Elastomers...

Science.gov (United States)

2010-07-12

... Status Materials Science Technology, Inc. (Specialty Elastomers and Fire Retardant Chemicals) Conroe... specialty elastomer manufacturing and distribution facility of Materials Science Technology, Inc., located... and distribution of specialty elastomers and fire retardant chemicals at the facility of Materials...

The effects of additives on the actuating performances of a dielectric elastomer actuator

International Nuclear Information System (INIS)

Nguyen, Huu Chuc; Doan, Vu Thuy; Park, JongKil; Koo, Ja Choon; Choi, Hyouk Ryeol; Lee, Youngkwan; Nam, Jae-do

2009-01-01

This paper presents a comprehensive study of the effects of additives on the performance of a dielectric elastomer actuator. Previously, a new dielectric elastomer material, called 'synthetic elastomer', was presented for the means of actuation, which permits changes in the mechanical as well as the electrical properties in order to meet the requirements of certain applications. This work studies how the electromechanical properties of the synthetic elastomer can be adjusted by combining two additives, namely dioctyl phthalate (DOP) and titanium dioxide (TiO 2 ). Experiments are carried out and the effects of each additive are compared to one another based on the actuation performances

Occupational Maxillofacial Trauma: Report of a Rare Case

Directory of Open Access Journals (Sweden)

Dervisoglou Theodoros

2015-03-01

Full Text Available Maxillofacial trauma, any physical trauma in the face, can involve soft tissues (lacerations, avulsions, bruises etc, bone injuries (fractures and dislocation, avulsed or fractured teeth (dental issues and special regions (nerves, eyes, salivary glands etc. As the most exposed part of the human body, the face can be susceptible to injuries in work-related accidents. Occupational accident in the maxillofacial region rates 0.9-5% and, in some cases, can reach 9%. Based on their occupation, patients are classified as farm and forestry workers, construction workers, factory workers, craftsmen, service workers, and office workers.

Hybrid matrices of TiO2 and TiO2–Ag nanofibers with silicone for high water flux photocatalytic degradation of dairy effluent

DEFF Research Database (Denmark)

Kanjwal, Muzafar Ahmad; Alm, Martin; Thomsen, Peter

2016-01-01

TiO2 and TiO2–Ag nanofibers were produced by electrospinning technique and surface coated on silicone elastomer (diameter: 10.0 mm; thickness: 2.0 mm) by dipcoating method. These coated hybrid nanoporous matrices were characterized by various morphological and physicochemical techniques (like SEM...

Development of procedures for calculating stiffness and damping properties of elastomers in engineering applications. Part 4: Testing of elastomers under a rotating load. [resonance testing

Science.gov (United States)

Darlow, M. S.; Smalley, A. J.

1977-01-01

A test rig designed to measure stiffness and damping of elastomer cartridges under a rotating load excitation is described. The test rig employs rotating unbalance in a rotor which runs to 60,000 RPM as the excitation mechanism. A variable resonant mass is supported on elastomer elements and the dynamic characteristics are determined from measurements of input and output acceleration. Five different cartridges are considered: three of these are buttons cartridges having buttons located in pairs, with 120 between each pair. Two of the cartridges consist of 360 elastomer rings with rectangular cross-sections. Dynamic stiffness and damping are measured for each cartridge and compared with predictions at different frequencies and different strains.

Toughened nanocomposites of polyamide-6 and polyepichlorohydrin elastomer: mechanical and morphological properties

International Nuclear Information System (INIS)

Pinotti, Caio A.; Goncalves, Maria C.; Felisberti, Maria I.

2009-01-01

Blends of polyamide 6, P A6, and polyepichlorohydrin elastomer, PE Pi, nano composites of P A6 and OMMT and toughened nano composites, P A6/PE Pi/OMMT were prepared by twin-screw extrusion. Nanocomposites of P A6 and organophilic clay presented morphology of exfoliated clay with the presence of some tactoids, which were investigated by XRD and TEM. The blends P A6/PE Pi are immiscible with morphology of elastomer disperse phase. The size of the elastomer phase in the PA6 matrix and a better distribution of these phase were achieved with the incorporation of the clay in the ternary nanocomposites. Toughened nano composites presented increases in Young's modulus, Izod impact strength and yield stress, comparing with the blends of P A6 and polyepichlorohydrin elastomer. (author)

Polyurethane elastomers in armour applications

NARCIS (Netherlands)

Carton, E.P.; Broos, J.P.F.

2012-01-01

The use of elastomers in ballistic protection products (armour) is limited to low threat levels and transparent armour solution components. Often armor is considered a parasitic mass that increases with increasing threat levels. Therefore, low weight solutions are welcomed and bulk polymers,

Additive manufacturing in maxillofacial reconstruction

Directory of Open Access Journals (Sweden)

Dincă Luciana Laura

2017-01-01

Full Text Available In this paper the benefits of using additive manufacturing technologies in maxillofacial reconstruction are highlighted. Based on a real clinical case, the paper describes the manufacture of an implant prototype replacing the right zygomatic bone and a part of maxilla using additive manufacturing technologies. The face is the most expressive part of the human body that makes us unique. It was shown that the maxillofacial prostheses help to improve the psychological state of patients affected by, because low self esteem feeling appears commonly to this patients with the facial defects. The aim of this paper is to show how using additive manufacturing technologies methods within this research, the producing a surgical model will help surgeon to improve the pre-operative planning. For this we used additive manufacturing technologies such as Stereolitography to achieve the biomodel and FDM-fused deposition modelling to obtain a prototype model because these technologies make it possible to obtain prosthesis according to the physical and mechanical requirements of the region of implantation.

Toward a predictive model for elastomer seals

Science.gov (United States)

Molinari, Nicola; Khawaja, Musab; Sutton, Adrian; Mostofi, Arash

Nitrile butadiene rubber (NBR) and hydrogenated-NBR (HNBR) are widely used elastomers, especially as seals in oil and gas applications. During exposure to well-hole conditions, ingress of gases causes degradation of performance, including mechanical failure. We use computer simulations to investigate this problem at two different length and time-scales. First, we study the solubility of gases in the elastomer using a chemically-inspired description of HNBR based on the OPLS all-atom force-field. Starting with a model of NBR, C=C double bonds are saturated with either hydrogen or intramolecular cross-links, mimicking the hydrogenation of NBR to form HNBR. We validate against trends for the mass density and glass transition temperature for HNBR as a function of cross-link density, and for NBR as a function of the fraction of acrylonitrile in the copolymer. Second, we study mechanical behaviour using a coarse-grained model that overcomes some of the length and time-scale limitations of an all-atom approach. Nanoparticle fillers added to the elastomer matrix to enhance mechanical response are also included. Our initial focus is on understanding the mechanical properties at the elevated temperatures and pressures experienced in well-hole conditions.

Management of maxillofacial trauma in emergency: An update of challenges and controversies

Directory of Open Access Journals (Sweden)

Anson Jose

2016-01-01

Full Text Available Trauma management has evolved significantly in the past few decades thereby reducing mortality in the golden hour. However, challenges remain, and one such area is maxillofacial injuries in a polytrauma patient. Severe injuries to the maxillofacial region can complicate the early management of a trauma patient owing to the regions proximity to the brain, cervical spine, and airway. The usual techniques of airway breathing and circulation (ABC management are often modified or supplemented with other methods in case of maxillofacial injuries. Such modifications have their own challenges and pitfalls in an already difficult situation.

Swelling behavior of γ-ray irradiated elastomers in boiling spray solution

International Nuclear Information System (INIS)

Yagi, Toshiaki; Kusama, Yasuo; Ito, Masayuki; Okada, Sohei; Yoshikawa, Masahito; Yoshida, Kenzo

1983-05-01

Elastomers swelled significantly by water sorption during a simulated LOCA test, and this phenomenon could cause the deterioration of their mechanical and electrical properties. Many factors like as radiation, heat, the composition of spray solution, types of elastomers and their formulation, related to the phenomenon. A relationship between swelling properties of the formulation-known various elastomers and the pre-aging conditions such as radiation dose and thermal aging period was studied by measuring their swelling behaviors in boiling spray solution (water and chemical solution). All eight elastomers tested showed remarkable swelling with an increase of radiation dose when they irradiated in air. A swelling in boiling water was about twice of in chemical solution. Some types of Neoprene and Hypalons had an optimum swelling dose where they showed the maxima. Over this dose, the swelling ratio decreased with dose. When irradiated under vacuum, its swelling ratio became significantly lower than that of exposed in air. This attributed the swelling phenomena closely related to radiation oxidation degradation. (author)

Bi-axially crumpled silver thin-film electrodes for dielectric elastomer actuators

International Nuclear Information System (INIS)

Low, Sze-Hsien; Lau, Gih-Keong

2014-01-01

Metal thin films, which have high conductivity, are much stiffer and may fracture at a much lower strain than dielectric elastomers. In order to fabricate compliant electrodes for use in dielectric elastomer actuators (DEAs), metal thin films have been formed into either zigzag patterns or corrugations, which favour bending and only allow uniaxial DEA deformations. However, biaxially compliant electrodes are desired in order to maximize generated forces of DEA. In this paper, we present crumpled metal thin-film electrodes that are biaxially compliant and have full area coverage over the dielectric elastomer. These crumpled metal thin-film electrodes are more stretchable than flat metal thin films; they remain conductive beyond 110% radial strain. Also, crumpling reduced the stiffening effect of metal thin films on the soft elastomer. As such, DEAs using crumpled metal thin-film electrodes managed to attain relatively high actuated area strains of up to 128% at 1.8 kV (102 Vμm −1 ). (paper)

Complaint liquid metal electrodes for dielectric elastomer actuators

Science.gov (United States)

Finkenauer, Lauren R.; Majidi, Carmel

2014-03-01

This work presents a liquid-phase metal electrode to be used with poly(dimethylsiloxane) (PDMS) for a dielectric elastomer actuator (DEA). DEAs are favorable for soft-matter applications where high efficiency and response times are desirable. A consistent challenge faced during the fabrication of these devices is the selection and deposition of electrode material. While numerous designs have been demonstrated with a variety of conductive elastomers and greases, these materials have significant and often intrinsic shortcomings, e.g. low conductivity, hysteresis, incapability of large deformations, and complex fabrication requirements. The liquid metal alloy eutectic Gallium-Indium (EGaIn) is a promising alternative to existing compliant electrodes, having both high conductivity and complete soft-matter functionality. The liquid electrode shares almost the same electrical conductivity as conventional metal wiring and provides no mechanical resistance to bending or stretching of the DEA. This research establishes a straightforward and effective method for quickly depositing EGaIn electrodes, which can be adapted for batch fabrication, and demonstrates the successful actuation of sample curved cantilever elastomer actuators using these electrodes. As with the vast majority of electrostatically actuated elastomer devices, the voltage requirements for these curved DEAs are still quite significant, though modifications to the fabrication process show some improved electrical properties. The ease and speed with which this method can be implemented suggests that the development of a more electronically efficient device is realistic and worthwhile.

Piezosurgery in oral and maxillofacial surgery

Czech Academy of Sciences Publication Activity Database

Pavlíková, G.; Foltán, R.; Horká, M.; Hanzelka, T.; Borunská, H.; Šedý, Jiří

2011-01-01

Roč. 40, č. 5 (2011), s. 451-457 ISSN 0901-5027 Institutional research plan: CEZ:AV0Z50390703 Keywords : piezosurgery * oral surgery * maxillofacial surgery Subject RIV: FJ - Surgery incl. Transplants; FH - Neurology (UEM-P) Impact factor: 1.506, year: 2011

[Application of anaerobic bacteria detection in oral and maxillofacial infection].

Science.gov (United States)

Bao, Zhen-ying; Lin, Qin; Meng, Yan-hong; He, Chun; Su, Jia-zeng; Peng, Xin

2016-02-18

To investigate the distribution and drug resistance of anaerobic bacteria in the patients with oral and maxillofacial infection. Aerobic and anaerobic bacteria cultures from 61 specimens of pus from the patients with oral and maxillofacial infection in the Department of Oral and Maxillofacial Surgery, Peking University School of Stomatology were identified. The culture type was evaluated by API 20A kit and drug resistance test was performed by Etest method. The clinical data and antibacterial agents for the treatment of the 61 cases were collected, and the final outcomes were recorded. The bacteria cultures were isolated from all the specimens, with aerobic bacteria only in 6 cases (9.8%), anaerobic bacteria only in 7 cases (11.5%), and both aerobic and anaerobic bacteria in 48 cases (78.7%). There were 55 infected cases (90.2%) with anaerobic bacteria, and 81 anaerobic bacteria stains were isolated. The highest bacteria isolation rate of Gram positive anaerobic bacteria could be found in Peptostreptococcus, Bifidobacterium and Pemphigus propionibacterium. No cefoxitin, amoxicillin/carat acid resistant strain was detected in the above three Gram positive anaerobic bacteria. The highest bacteria isolation rate of Gram negative anaerobic bacteria could be detected in Porphyromonas and Prevotella. No metronidazole, cefoxitin, amoxicillin/carat acid resistant strain was found in the two Gram negative anaerobic bacteria. In the study, 48 patients with oral and maxillofacial infection were treated according to the results of drug resistance testing, and the clinical cure rate was 81.3%. Mixed aerobic and anaerobic bacteria cultures are very common in most oral and maxillofacial infection patients. Anaerobic bacteria culture and drug resistance testing play an important role in clinical treatment.

Electrical behaviour of synthetic elastomers under gamma irradiation

International Nuclear Information System (INIS)

Zaharescu, Traian; Ciuprina, Florin

2006-01-01

The exposure of ethylene-propylene elastomers to the action of gamma radiation causes the modification of chemical state of polymer matrix by the formation of oxygenated products. The accumulation of dipoles modifies the electrical behaviour of materials. The value of resistance increases more than three times at increasing the dose up to 200 kGy. The absorption/resorption current measurements demonstrate the bad consequence of the inversion of polarity for applied voltages. Differences between the two sorts of synthetic elastomers (ethylene-propylene copolymer and ethylene-propylene terpolymer) were pointed out. (author)

Development of energy-harvesting system using deformation of magnetic elastomer

Science.gov (United States)

Shinoda, Hayato; Tsumori, Fujio

2018-06-01

In this paper, we propose a power generation method using the deformation of a magnetic elastomer for vibration energy harvesting. The magnetic flux lines in the structure of the magnetic elastomer could be markedly changed if the properly designed structure was expanded and contracted in a static magnetic field. We set a coil on the magnetic elastomer to generate electricity by capturing this change in magnetic flux flow. We fabricated a centimeter-scale device and demonstrated that it generated 10.5 mV of maximum voltage by 10 Hz vibration. We also simulated the change in the magnetic flux flow using finite element analysis, and compared the result with the experimental data. Furthermore, we evaluated the power generation of a miniaturized device.

Parameters design of the dielectric elastomer spring-roll bending actuator (Conference Presentation)

Science.gov (United States)

Li, Jinrong; Liu, Liwu; Liu, Yanju; Leng, Jinsong

2017-04-01

Dielectric elastomers are novel soft smart material that could deform sustainably when subjected to external electric field. That makes dielectric elastomers promising materials for actuators. In this paper, a spring-roll actuator that would bend when a high voltage is applied was fabricated based on dielectric elastomer. Using such actuators as active parts, the flexible grippers and inchworm-inspired crawling robots were manufactured, which demonstrated some examples of applications in soft robotics. To guide the parameters design of dielectric elastomer based spring-roll bending actuators, the theoretical model of such actuators was established based on thermodynamic theories. The initial deformation and electrical induced bending angle of actuators were formulated. The failure of actuators was also analyzed considering some typical failure modes like electromechanical instability, electrical breakdown, loss of tension and maximum tolerant stretch. Thus the allowable region of actuators was determined. Then the bending angle-voltage relations and failure voltages of actuators with different parameters, including stretches of the dielectric elastomer film, number of active layers, and dimensions of spring, were investigated. The influences of each parameter on the actuator performances were discussed, providing meaningful guidance to the optical design of the spring-roll bending actuators.

Semi-active control of a sandwich beam partially filled with magnetorheological elastomer

Science.gov (United States)

Dyniewicz, Bartłomiej; Bajkowski, Jacek M.; Bajer, Czesław I.

2015-08-01

The paper deals with the semi-active control of vibrations of structural elements. Elastomer composites with ferromagnetic particles that act as magnetorheological fluids are used. The damping coefficient and the shear modulus of the elastomer increases when it is exposed to an electro-magnetic field. The control of this process in time allows us to reduce vibrations more effectively than if the elastomer is permanently exposed to a magnetic field. First the analytical solution for the vibrations of a sandwich beam filled with an elastomer is given. Then the control problem is defined and applied to the analytical formula. The numerical solution of the minimization problem results in a periodic, perfectly rectangular control function if free vibrations are considered. Such a temporarily acting magnetic field is more efficient than a constantly acting one. The surplus reaches 20-50% or more, depending on the filling ratio of the elastomer. The resulting control was verified experimentally in the vibrations of a cantilever sandwich beam. The proposed semi-active control can be directly applied to engineering vibrating structural elements, for example helicopter rotors, aircraft wings, pads under machines, and vehicles.

Numerical Modelling of Metal-Elastomer Spring Nonlinear Response for Low-Rate Deformations

Directory of Open Access Journals (Sweden)

Sikora Wojciech

2018-03-01

Full Text Available Advanced knowledge of mechanical characteristics of metal-elastomer springs is useful in their design process and selection. It can also be used in simulating dynamics of machine where such elements are utilized. Therefore this paper presents a procedure for preparing and executing FEM modelling of a single metal-elastomer spring, also called Neidhart’s spring, for low-rate deformations. Elastomer elements were made of SBR rubber of two hardness values: 50°Sh and 70°Sh. For the description of material behaviour the Bergström-Boyce model has been used.

Patterning conductive PDMS nanocomposite in an elastomer using microcontact printing

International Nuclear Information System (INIS)

Liu, Chao-Xuan; Choi, Jin-Woo

2009-01-01

This paper introduces a simple method of embedding conductive and flexible elastomer micropatterns into a bulk elastomer. Employing microcontact printing and cast molding techniques, patterns consisting of conductive poly(dimethylsiloxane) (PDMS) composites mixed with multi-walled carbon nanotubes (MWCNTs) are embedded into bulk PDMS to form all-elastomer devices. To pattern conductive composites, a micromachined printing mold is utilized to transfer composite ink from a spin-coated thin layer to another substrate. Distinct from previously reported approaches, the printing mold in this technique, once fabricated, can be repeatedly used to generate new patterns and therefore greatly simplifies the device fabrication process and improves its efficiency. Manufactured devices with embedded conductive patterns exhibit excellent mechanical flexibility. With characterization of printing reliability, electrical conductivity of the composites is also shown with different loading percentages of MWCNTs. Furthermore, a simple strain gauge was fabricated and tested to demonstrate the potential applications of embedded conductive patterns. Overall, this approach demonstrates feasibility to be a simple method to pattern conductive elastomers that work as electrodes or sensing probes in PDMS-based devices. With further development, this technology yields many potential applications in lab-on-a-chip systems

Aging of elastomers in CANDU pressure boundary service

International Nuclear Information System (INIS)

VanBerlo, C.; Leidner, J.

1987-09-01

This report describes the properties and aging of elastomers, and examines the performance of major elastomeric components in CANDU pressure boundary service. The components examined are vacuum building roof seals, pressure relief duct seals, airlock door seals, fuelling machine hoses, and cable penetrations. For each of these components, the design requirements, technical specifications and component testing procedures are compared with applicable standards. Information on actual and recommended monitoring and maintenance methods is presented. Operational and environmental stressors are identified. Component failure modes, causes and frequencies are described, as well as the remedial action taken. Many different elastomers are used in CANDU plants, for many different applications. Standards and manufacturers' recommendations are not consistent and may vary from one component to another. Accordingly, the monitoring, maintenance and replacement practices tend to vary from one application to another, and may also be different at different stations. Recommendations are given in this report for improved monitoring and maintenance, in an attempt to provide more consistency in approach. A summary of some experiences with elastomers from non-Canadian sources is contained in the last section. 125 refs

KNOWLEDGE GAPS IN ORAL AND MAXILLOFACIAL SURGERY

DEFF Research Database (Denmark)

Österberg, Marie; Holmlund, Anders; Sunzel, Bo

2017-01-01

OBJECTIVES: The aim of this study was to evaluate available knowledge and identify knowledge gaps within the field of oral and maxillofacial surgery, by systematically collecting and evaluating systematic reviews. Twelve specific domains were selected: surgical removal of teeth, antibiotic....... However, in all domains, the search revealed a large number of knowledge gaps. Also of concern was the lack of data regarding health economics and ethics. CONCLUSIONS: In conclusion, there is a need for well-conducted clinical research in the fields of oral and maxillofacial surgery........ RESULTS: In all, 1,778 abstracts were identified, of which 200 met the inclusion criteria. Forty-five systematic reviews were assessed as of high to moderate quality. The results disclosed some existing evidence in a few domains, such as surgical removal of teeth and implant survival after sinus lifts...

Low burnout risk and high engagement levels among oral and maxillofacial surgeons

NARCIS (Netherlands)

Gorter, R.C.; Jacobs, B.L.T.H.; Allard, R.H.B.

2012-01-01

Little is known about the well-being of oral and maxillofacial surgeons. The aim of this study was to measure the levels of burnout risk and the demanding work aspects of Dutch oral and maxillofacial surgeons, as well as the levels of positive work engagement and stimulating aspects of the work

Critical Role of Diels-Adler Adducts to Realise Stretchable Transparent Electrodes Based on Silver Nanowires and Silicone Elastomer

Science.gov (United States)

Heo, Gaeun; Pyo, Kyoung-Hee; Lee, Da Hee; Kim, Youngmin; Kim, Jong-Woong

2016-05-01

This paper presents the successful fabrication of a transparent electrode comprising a sandwich structure of silicone/Ag nanowires (AgNWs)/silicone equipped with Diels-Alder (DA) adducts as crosslinkers to realise highly stable stretchability. Because of the reversible DA reaction, the crosslinked silicone successfully bonds with the silicone overcoat, which should completely seal the electrode. Thus, any surrounding liquid cannot leak through the interfaces among the constituents. Furthermore, the nanowires are protected by the silicone cover when they are stressed by mechanical loads such as bending, folding, and stretching. After delicate optimisation of the layered silicone/AgNW/silicone sandwich structure, a stretchable transparent electrode which can withstand 1000 cycles of 50% stretching-releasing with an exceptionally high stability and reversibility was fabricated. This structure can be used as a transparent strain sensor; it possesses a strong piezoresistivity with a gauge factor greater than 11.

Dracunculiasis in oral and maxillofacial surgery.

Science.gov (United States)

Kim, Soung Min

2016-04-01

Dracunculiasis, otherwise known as guinea worm disease (GWD), is caused by infection with the nematode Dracunculus medinensis. This nematode is transmitted to humans exclusively via contaminated drinking water. The transmitting vectors are Cyclops copepods (water fleas), which are tiny free-swimming crustaceans usually found abundantly in freshwater ponds. Humans can acquire GWD by drinking water that contains vectors infected with guinea worm larvae. This disease is prevalent in some of the most deprived areas of the world, and no vaccine or medicine is currently available. International efforts to eradicate dracunculiasis began in the early 1980s. Most dentists and maxillofacial surgeons have neglected this kind of parasite infection. However, when performing charitable work in developing countries near the tropic lines or other regions where GWD is endemic, it is important to consider GWD in cases of swelling or tumors of unknown origin. This paper reviews the pathogenesis, epidemiology, clinical criteria, diagnostic criteria, treatment, and prevention of dracunculiasis. It also summarizes important factors for maxillofacial surgeons to consider.

Retention systems for extraoral maxillofacial prosthetic implants: a critical review.

Science.gov (United States)

Cobein, M V; Coto, N P; Crivello Junior, O; Lemos, J B D; Vieira, L M; Pimentel, M L; Byrne, H J; Dias, R B

2017-10-01

We describe the techniques available for retention of implant-supported prostheses: bar-clips, O-rings, and magnets. We present reported preferences and, although this is limited by the heterogeneity of methods used and patients studied, we hope we have identified the best retention systems for maxillofacial prosthetic implants. If practitioners know the advantages and disadvantages of each system, they can choose the most natural and comfortable prosthesis. We searched the PubMed and Scopus databases, and restricted our search to papers published 2001-13. MeSH terms used were Maxillofacial prosthesis and Craniofacial prosthesis OR Craniofacial prostheses. We found a total of 2630 papers, and after duplicates had been removed we analysed the rest and found 25 papers for review. Of these, 12 were excluded because they were case reports or non-systematic reviews. Of the remaining 13, 10 described group analyses and seemed appropriate to find practitioner's choices, as cited in the abstract (n=1611 prostheses). Three papers did not mention the type of prosthetic connection used, so were excluded. The most popular choices for different conditions were analysed, though the sites and retention systems were not specified in all 10 papers. The bar-clip system was the most used in auricular (6/10 papers) and nasal prostheses (4/10). For the orbital region, 6/10 favoured magnets. Non-osseointegrated mechanical or adhesive retention techniques are the least expensive and have no contraindications. When osseointegrated implants are possible, each facial region has a favoured system. The choice of system is influenced by two factors: standard practice and the abilities of the maxillofacial surgeon and maxillofacial prosthetist. Copyright © 2017 The British Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Radiation cured acrylonitrile--butadiene elastomers

International Nuclear Information System (INIS)

Eldred, R.J.

1976-01-01

In accordance with a preferred embodiment of this invention, the ultimate elongation of an electron beam radiation cured acrylonitrile-butadiene elastomer is significantly increased by the incorporation of a preferred noncrosslinking monomer, glycidyl methacrylate, in combination with the conventional crosslinking monomer, trimethylolpropanetrimethacrylate, prior to the radiation curing process

Bibliometric analysis of oral and maxillofacial cytology-related articles published in a cytology journal from India.

Science.gov (United States)

Shamim, Thorakkal

2018-01-01

There is a paucity of information about the oral and maxillofacial cytology-related articles published in a cytology journal. Journal of Cytology (JOC) is the official publication of Indian Academy of Cytologists. This study aimed to audit the oral and maxillofacial cytology-related articles published in JOC from 2007 to 2015 over a 9-year period. Bibliometric analysis of issues of JOC from 2007 to 2015 was performed using web-based search. The articles published were analyzed for type of article and individual topic of oral and maxillofacial cytology. The articles published were also checked for authorship trends. Of the total 93 published articles related to oral and maxillofacial cytology, original articles (43) and case reports (33) contribute the major share. The highest number of oral and maxillofacial cytology-related articles was published in 2014 with 17 articles and the least published year was 2010 with three articles. Among the oral and maxillofacial cytology-related articles published in JOC, diseases of salivary gland (26) followed by oral exfoliated cells (17), soft tissue tumors (7), round cell tumors (6) and spindle cell neoplasms (5) form the major attraction of the contributors. The largest numbers of published articles related to oral and maxillofacial cytology were received from Postgraduate Institute of Medical Education and Research, Chandigarh (5), and Jawaharlal Nehru Medical College, Aligarh (5). This paper may be considered as a baseline study for the bibliometric information regarding oral and maxillofacial cytology-related articles published in India.

Mechanical tests for validation of seismic isolation elastomer constitutive models

International Nuclear Information System (INIS)

Kulak, R.F.; Hughes, T.H.

1992-01-01

High damping laminated elastomeric bearings are becoming the preferred device for seismic isolation of large buildings and structures, such as nuclear power plants. The key component of these bearings is a filled natural rubber elastomer. This material exhibits nonlinear behavior within the normal design range. The material damping cannot be classified as either viscous or hysteritic, but it seems to fall somewhere in between. This paper describes a series of tests that can be used to characterize the mechanical response of these elastomers. The tests are designed to determine the behavior of the elastomer in the time scale of the earthquake, which is typically from 30 to 60 seconds. The test results provide data for use in determining the material parameters associated with nonlinear constitutive models. 4 refs

Rigidity-tuning conductive elastomer

Science.gov (United States)

Shan, Wanliang; Diller, Stuart; Tutcuoglu, Abbas; Majidi, Carmel

2015-06-01

We introduce a conductive propylene-based elastomer (cPBE) that rapidly and reversibly changes its mechanical rigidity when powered with electrical current. The elastomer is rigid in its natural state, with an elastic (Young’s) modulus of 175.5 MPa, and softens when electrically activated. By embedding the cPBE in an electrically insulating sheet of polydimethylsiloxane (PDMS), we create a cPBE-PDMS composite that can reversibly change its tensile modulus between 37 and 1.5 MPa. The rigidity change takes ˜6 s and is initiated when a 100 V voltage drop is applied across the two ends of the cPBE film. This magnitude of change in elastic rigidity is similar to that observed in natural skeletal muscle and catch connective tissue. We characterize the tunable load-bearing capability of the cPBE-PDMS composite with a motorized tensile test and deadweight experiment. Lastly, we demonstrate the ability to control the routing of internal forces by embedding several cPBE-PDMS ‘active tendons’ into a soft robotic pneumatic bending actuator. Selectively activating the artificial tendons controls the neutral axis and direction of bending during inflation.

Rigidity-tuning conductive elastomer

International Nuclear Information System (INIS)

Shan, Wanliang; Diller, Stuart; Tutcuoglu, Abbas; Majidi, Carmel

2015-01-01

We introduce a conductive propylene-based elastomer (cPBE) that rapidly and reversibly changes its mechanical rigidity when powered with electrical current. The elastomer is rigid in its natural state, with an elastic (Young’s) modulus of 175.5 MPa, and softens when electrically activated. By embedding the cPBE in an electrically insulating sheet of polydimethylsiloxane (PDMS), we create a cPBE–PDMS composite that can reversibly change its tensile modulus between 37 and 1.5 MPa. The rigidity change takes ∼6 s and is initiated when a 100 V voltage drop is applied across the two ends of the cPBE film. This magnitude of change in elastic rigidity is similar to that observed in natural skeletal muscle and catch connective tissue. We characterize the tunable load-bearing capability of the cPBE–PDMS composite with a motorized tensile test and deadweight experiment. Lastly, we demonstrate the ability to control the routing of internal forces by embedding several cPBE–PDMS ‘active tendons’ into a soft robotic pneumatic bending actuator. Selectively activating the artificial tendons controls the neutral axis and direction of bending during inflation. (paper)

Publication bias in oral and maxillofacial surgery journals: an observation on published controlled trials.

Science.gov (United States)

Pitak-Arnnop, Poramate; Sader, Robert; Rapidis, Alexander D; Dhanuthai, Kittipong; Bauer, Ute; Herve, Chistian; Hemprich, Alexander

2010-01-01

Publication bias (PB) diminishes the full distribution of research, distorts and discredits the scientific record, and thus compromises evidence-based practice. The objective of this study was to analyse published controlled trials with regard to PB in leading oral and maxillofacial surgery (OMS) journals. All controlled trials published in the International Journal of Oral and Maxillofacial Surgery, Journal of Cranio-Maxillofacial Surgery, Journal of Oral and Maxillofacial Surgery, and British Journal of Oral and Maxillofacial Surgery in 2008 were analysed for a primary outcome, country of authors, sample size, gender of the first author, funding source and location of the study. Of 952 published articles, 53 controlled trials (5.7%) were identified. The OMS journals preferentially published controlled trials with a positive outcome (77.4%) and from high-income countries (73.6%). Single-centred trials (86.8%) with low sample size (njournals should establish measures to eliminate PB to uphold scientific integrity. However, this study was an observation based on the published articles. An analysis of all submitted manuscripts would provide more accurate estimates of PB. Ethical considerations on PB are also discussed.

Collapse of triangular channels in a soft elastomer

Science.gov (United States)

Tepáyotl-Ramírez, Daniel; Lu, Tong; Park, Yong-Lae; Majidi, Carmel

2013-01-01

We extend classical solutions in contact mechanics to examine the collapse of channels in a soft elastomer. These channels have triangular cross-section and collapse when pressure is applied to the surrounding elastomer. Treating the walls of the channel as indenters that penetrate the channel base, we derive an algebraic mapping between pressure and cross-sectional area. These theoretical predictions are in strong agreement with results that we obtain through finite element analysis and experimental measurements. This is accomplished without data fitting and suggests that the theoretical approach may be generalized to a broad range of cross-sectional geometries in soft microfluidics.

Self-sorting of guests and hard blocks in bisurea-based thermoplastic elastomers

NARCIS (Netherlands)

Botterhuis, N.E.; Karthikeyan, S.; Spiering, A.J.H.; Sijbesma, R.P.

2010-01-01

Self-sorting in thermoplastic elastomers was studied using bisurea-based thermoplastic elastomers (TPEs) which are known to form hard blocks via hierarchical aggregation of bisurea segments into ribbons and of ribbons into fibers. Self-sorting of different bisurea hard blocks in mixtures of polymers

Electromechanical stability of electro-active silicone filled with high permittivity particles undergoing large deformation

International Nuclear Information System (INIS)

Liu, Liwu; Liu, Yanju; Zhang, Zhen; Leng, Jinsong; Li, Bo

2010-01-01

In this paper, an expression for the permittivity of electro-active silicone undergoing large deformation with high permittivity particles filled uniformly has been proposed. Two expressions are proposed for the permittivity, one based on experimental tests and the other based on the theory of composite material. By applying the thermodynamic model incorporating linear dielectric permittivity and nonlinear hyperelastic performance, the mechanical performance and electromechanical stability of the coupling system constituted by silicone filled with PMN–PT have been studied. The results show that the critical electric field decreases, namely the stability performance of the system declines when the content of PMN–PT c(v) increases and the electrostrictive coefficients increase. The results are beneficial for us to understand deeply the influence of the filled particle on the stability performance of silicone and to guide the design and manufacture of actuators and sensors based on dielectric elastomers

Elastomer damper performance - A comparison with a squeeze film for a supercritical power transmission shaft

Science.gov (United States)

Zorzi, E. S.; Burgess, G.; Cunningham, R.

1980-01-01

This paper describes the design and testing of an elastomer damper on a super-critical power transmission shaft. The elastomers were designed to provide acceptable operation through the fourth bending mode and to control synchronous as well as nonsynchronous vibration throughout the operating range. The design of the elastomer was such that it could be incorporated into the system as a replacement for a squeeze-film damper without a reassembly, which could have altered the imbalance of the shaft. This provided a direct comparison of the elastomer and squeeze-film dampers without having to assess the effect of shaft imbalance changes.

ASSESSMENT OF THE INFLUENCE OF RADIATION AND DEFORMATION ON THE ELASTOMER DETERIORATION BY USING FUZZY LOGIC

Directory of Open Access Journals (Sweden)

Jasminka Bonato

2017-01-01

Full Text Available Elastomers belong to the group of polymer materials and they have an important role as technical material in the shipbuilding industry. The radiation crosslinking of elastomers shows significant advantages over chemical crosslinking. It can improve mechanical strength, resistance to chemicals and insulation properties of elastomers. An undesirable side reaction, which can occur during radiation, is the degradation process. This results in cracks breaking, chemical disintegration and reduction of mechanical properties of elastomers. In this paper fuzzy logic is used to estimate the influence of radiation and deformation on the behavior of elastomer samples. A Gaussian model is created according to both the experts' experience and the measuring data. The results of the model are calculated by using the Normalized Roth Mean Square Error (NRMSE and the Roth Mean Square Error (RMSE. The so developed model gives new conceptions, which offer a possibility to improve the application of elastomer materials.

Fabrication and electromechanical examination of a spherical dielectric elastomer actuator

International Nuclear Information System (INIS)

Ahmadi, S; Gooyers, M; Soleimani, M; Menon, C

2013-01-01

In this paper, a procedure for fabricating and testing a seamless spherical dielectric elastomer actuator (DEA) is presented. In previously developed spherical prototypes, the DEA material is pre-strained by a rigid frame to improve the actuator’s output force; however, it is possible to pre-strain a spherical DEA by inflating the sample with a liquid or gas as long as the sample contains the pressure. In this work, a very compliant silicone-based material was used to fabricate a nearly spherical balloon-shaped prototype. The DEA sample was inflated by air and various electrical-actuation regimes were considered. The performance of the DEA sample was studied using an analytical and a finite element-based model. An Ogden hyperelastic model was used in formulation of the analytical model to include nonlinear behavior of the silicone material. Full statistical analysis of the experimental and numerical results was carried out using the root-mean-square (RMS) error and the normalized RMS error. The analytical and FEM results were in good agreement with the experimental data. According to modeling results, it was found that the DEA’s actuation force can be mainly improved by increasing the voltage, reducing the thickness, lowering the stiffness, and/or increasing the initial pressure. As an example, a three-fold increase of the actuation force was found when the thickness was reduced to half of its initial value. This improvement of the efficiency suggests that the spherical DEA is suitable for use in several applications if an appropriate design with optimal governing parameters is developed. (paper)

Knowledge and Awareness of Medical Practitioners of Jazan City towards Oral and Maxillofacial Surgery as a Specialty.

Science.gov (United States)

Ali, Fareedi Mukram; Al-Iryani, Ghassan M; Namis, Sultan Mohammed; Hezam, Asma Ali; Swaid, Salma Abdu; Alomar, Anas Esam

2018-03-15

In many health services communities the scope of oral and maxillofacial surgery (OMFS) as a discipline is frequently not probably understood. Good awareness towards OMFS among different branches of health services providers is essential for better referral strategies and will be for the benefit of the patient. The cross-sectional study was done using a specially prepared questionnaire distributed randomly to 125 general medical practitioners working in Jazan province. In this questionnaire, there were also some close-ended questions to evaluate awareness regarding a variety of conditions treated by the oral and maxillofacial surgeons. Out of 125 participants, 105 (84%) were aware of the oral and maxillofacial surgery as a speciality branch of dentistry. Only 52 (41.6%) participants were aware of the different treatment modalities coming under the scope of oral and maxillofacial surgery. Also in the referral of cases to the oral and maxillofacial surgeon, 50 (40%) participants referred their oral and maxillofacial region cases to OMS. Tooth removal was the only procedure where most of the medical practitioners knew it is a speciality procedure of the oral and maxillofacial surgeon. For facial fractures, 76 medical practitioners believe it comes under the scope of the orthopaedic surgeon. Similarly, for facial abscesses, 81 and 36 practitioners responded that it is a job of a general surgeon and OMS respectively. There is low awareness toward the scope of oral and maxillofacial surgery in the medical community. Knowledge and awareness of the scope of oral and maxillofacial surgery can improve the success and promptness of delivery of health services.

Frequency of Maxillofacial Injuries Among Athletes-Members of Various Sports Federations in Iranform 1998-2001

Directory of Open Access Journals (Sweden)

H Mahmoud Hasehmi

2003-02-01

Full Text Available Nowadays, sport injuries constitute a major part of social accidents. The aim of the presentstudy, was to investigate the frequency of maxillofacial injuries among athletes-members of differentsports federations in Iran from 1998-2001. For this reason files which was related to sport injuries of men and women athletes-members of sports federations were studied in Medical Federation of the Islamic Republic of Iran Sports Organization. The information were received through 26 medical organizations,located in different states of the country. The results showed that maxillofacial injuries constitute the major part of the sports injuries. In male athletes, football was the most important cause for maxillofacial injuries. However, mountain climbing and skiing play the least role in this field. Among female athletes,karate was the cause of the highest rate of maxillofacial sport injuries. Diving, mountain climbing and skiing cause the least number of maxillofacial accidents. Nasal fracture was the most common sport injury among Iraninan male and female athletes.

Effect of the filler on radiolysis of filled elastomers

International Nuclear Information System (INIS)

Komarov, S.A.; Erastov, A.Kh.; Kolesnikov, A.A.; Gostikina, A.V.; Mal'kov, A.M.; Korovkin, V.V.

1987-01-01

The effect of the type and concentration of filler (A-175 Aerosil, PM-75 technical carbon, BS-100 white black, kaolin, titanium oxide) on the radiation yield of elastomers of different chemical nature was studied. The extreme character of the dependence of the radiation yield of paramagnetic centers on the concentration of filler, common to the systems studied, was established; it was due to the features of the colloid chemical structure of the filled elastomers and particularly to processes of cross-linking of the filter

Electric Conductivity and Dielectric-Breakdown Behavior for Polyurethane Magnetic Elastomers.

Science.gov (United States)

Sasaki, Shuhei; Tsujiei, Yuri; Kawai, Mika; Mitsumata, Tetsu

2017-02-23

The electric-voltage dependence of the electric conductivity for cross-linked and un-cross-linked magnetic elastomers was measured at various magnetic fields, and the effect of cross-linking on the electric conductivity and the dielectric-breakdown behavior was investigated. The electric conductivity for un-cross-linked elastomers at low voltages was independent of magnetic fields and the volume fraction of magnetic particles, indicating the electric conduction in the polyurethane matrix. At high voltages, the electric conductivity increased with the magnetic field, showing the electric conduction via chains of magnetic particles. On the other hand, the electric conductivity at low voltages for cross-linked elastomers with volume fractions below 0.06 was independent of the magnetic field, suggesting the electric conduction in the polyurethane matrix. At volume fractions above 0.14, the electric conductivity increased with the magnetic field, suggesting the electric conduction via chains of magnetic particles. At high voltages, the electric conductivity for cross-linked elastomers with a volume fraction of 0.02 was independent of the magnetic field, indicating the electric conduction through the polyurethane matrix. At volume fractions above 0.06, the electric conductivity suddenly increased at a critical voltage, exhibiting the dielectric breakdown at the bound layer of magnetic particles and/or the discontinuous part between chains.

Maxillofacial injuries due to work-related accidents in the North West of Italy.

Science.gov (United States)

Roccia, Fabio; Boffano, Paolo; Bianchi, Francesca Antonella; Gerbino, Giovanni

2013-09-01

The aim of this study was to assess the incidence and patterns of work-related maxillofacial injuries, identifying worker categories with a high risk of injury. From a systematic computer-assisted database that has continuously recorded patients hospitalized with maxillofacial fractures, only patients with work-related injuries were considered. Occupation, mechanism of injury, and demographic and clinical data were analyzed. Work-related facial injuries represented the fifth most common cause of injury, with a percentage of 6.3 %. Maxillofacial fractures were most often seen in construction workers (37.9 %). The middle third was involved in 67 % of the cases; the mandible was the most frequently injured site. Work-related maxillofacial trauma is rare, but it is often complex and challenging as Facial Injury Severity Scale values show. In agreement with the few published reports, construction workers, together with farm and forestry workers, are at the highest risk of injuries, mainly because of struck by a thrown, projected, or falling object.

On a Minimum Problem in Smectic Elastomers

International Nuclear Information System (INIS)

Buonsanti, Michele; Giovine, Pasquale

2008-01-01

Smectic elastomers are layered materials exhibiting a solid-like elastic response along the layer normal and a rubbery one in the plane. Balance equations for smectic elastomers are derived from the general theory of continua with constrained microstructure. In this work we investigate a very simple minimum problem based on multi-well potentials where the microstructure is taken into account. The set of polymeric strains minimizing the elastic energy contains a one-parameter family of simple strain associated with a micro-variation of the degree of freedom. We develop the energy functional through two terms, the first one nematic and the second one considering the tilting phenomenon; after, by developing in the rubber elasticity framework, we minimize over the tilt rotation angle and extract the engineering stress

Silicone-based composite materials simulate breast tissue to be used as ultrasonography training phantoms.

Science.gov (United States)

Ustbas, Burcin; Kilic, Deniz; Bozkurt, Ayhan; Aribal, Mustafa Erkin; Akbulut, Ozge

2018-03-02

A silicone-based composite breast phantom is fabricated to be used as an education model in ultrasonography training. A matrix of silicone formulations is tracked to mimic the ultrasonography and tactile response of human breast tissue. The performance of two different additives: (i) silicone oil and (ii) vinyl-terminated poly (dimethylsiloxane) (PDMS) are monitored by a home-made acoustic setup. Through the use of 75 wt% vinyl-terminated PDMS in two-component silicone elastomer mixture, a sound velocity of 1.29 ± 0.09 × 10 3  m/s and an attenuation coefficient of 12.99 ± 0.08 dB/cm-values those match closely to the human breast tissue-are measured with 5 MHz probe. This model can also be used for needle biopsy as well as for self-exam trainings. Herein, we highlight the fabrication of a realistic, durable, accessible, and cost-effective training platform that contains skin layer, inner breast tissue, and tumor masses. Copyright © 2018. Published by Elsevier B.V.

New reusable elastomer electrodes for assessing body composition

International Nuclear Information System (INIS)

Moreno, M-V; Chaset, L; Bittner, P A; Barthod, C; Passard, M

2013-01-01

The development of telemedicine requires finding solutions of reusable electrodes for use in patients' homes. The objective of this study is to evaluate the relevance of reusable elastomer electrodes for measuring body composition. We measured a population of healthy Caucasian (n = 17). A measurement was made with a reference device, the Xitron®, associated with AgCl Gel electrodes (Gel) and another measurement with a multifrequency impedancemeter Z-Metrix® associated with reusable elastomer electrodes (Elast). We obtained a low variability with an average error of repeatability of 0.39% for Re and 0.32% for Rinf. There is a non significantly difference (P T-test > 0.1) about 200 ml between extracellular water Ve measured with Gel and Elast in supine and in standing position. For total body water Vt, we note a non significantly difference (P T-test > 0.1) about 100 ml and 2.2 1 respectively in supine and standing position. The results give low dispersion, with R 2 superior to 0.90, with a 1.5% maximal error between Gel and Elast on Ve in standing position. It looks possible, taking a few precautions, using elastomer electrodes for assessing body composition.

Education of Oral and Maxillofacial Radiology in South Korea

International Nuclear Information System (INIS)

Choi, Soon Chul

2009-01-01

Although x-ray had been used in Dental Clinic and taught as Roentgenology as a part of other lectures, the independent lecture was established at Seoul National University in 1953. The first independent Department was separated from the Department of Oral Surgery at Seoul National University in 1963. Nowadays, there are 6 national and 5 private dental schools in South Korea. Each dental school has a Department of Oral and Maxillofacial Radiology, which fulfills its role in student education and clinical service. What is specially noteworthy is that 8 of the 11 dental schools have changed or will change from the 2+4 year system to 4+4 year system (postgraduate course). The curriculum has also been or is being amended according to this change. Although the contents of courses for Oral and Maxillofacial Radiology are not much different among dental schools, the methods and structure of education are various. We have to do a systematic and comprehensive analysis of the present educational methods and structure of Oral and Maxillofacial Radiology and need to seek the new and more suitable ones based on competency.

Education of Oral and Maxillofacial Radiology in South Korea

Energy Technology Data Exchange (ETDEWEB)

Choi, Soon Chul [Department of Oral and Maxillofacial Radiology, Dental Research Institute, School of Dentistry, Seoul National University, Seoul (Korea, Republic of)

2009-03-15

Although x-ray had been used in Dental Clinic and taught as Roentgenology as a part of other lectures, the independent lecture was established at Seoul National University in 1953. The first independent Department was separated from the Department of Oral Surgery at Seoul National University in 1963. Nowadays, there are 6 national and 5 private dental schools in South Korea. Each dental school has a Department of Oral and Maxillofacial Radiology, which fulfills its role in student education and clinical service. What is specially noteworthy is that 8 of the 11 dental schools have changed or will change from the 2+4 year system to 4+4 year system (postgraduate course). The curriculum has also been or is being amended according to this change. Although the contents of courses for Oral and Maxillofacial Radiology are not much different among dental schools, the methods and structure of education are various. We have to do a systematic and comprehensive analysis of the present educational methods and structure of Oral and Maxillofacial Radiology and need to seek the new and more suitable ones based on competency.

Study on the control of the compositions and properties of a biodegradable polyester elastomer

Energy Technology Data Exchange (ETDEWEB)

Liu Quanyong; Weng Jingyi; Zhang Liqun [Key Laboratory of Beijing City on Preparation and Processing of Novel Polymer Materials, Beijing University of Chemical Technology, Beijing 100029 (China); Tan Tianwei, E-mail: liu_quanyong@126.co, E-mail: zhanglq@mail.buct.edu.c [Key Laboratory of Bioprocess of Beijing, Beijing University of Chemical Technology, Beijing 100029 (China)

2009-04-15

Biodegradable polyester elastomers are widely reported to be applied in varied biomedical fields. In this paper, we attempt to investigate how both the thermal-curing time and molar ratio of the monomers affect the final compositions and properties of the novel poly(glycerol-sebacate-citrate) (PGSC) elastomers. First, PGSC elastomers are obtained after the thermal curing of the moldable mixtures consisting of citric acid and poly(glycerol-sebacate) (PGS) prepolymers synthesized in the lab. Then further studies show that, on the one hand, the control of longer thermal-curing time results in elastomers with less sol, lower swelling degree, slower degradation, greater mechanical strength and higher glass transition temperature and, on the other hand, the crosslink with more citric acid is advantageous to greatly improving their mechanical strength and glass transition temperatures, simultaneously decreasing their sol contents, swelling degrees and degradation rates. The PGSC elastomers show thermosetting properties, certain strength, mass losses lower than 20% after 4-week degradation and durative water absorption during degradation. Thus they might be potentially used as degradable bio-coatings, varied soft biomedical membranes and drug delivery matrices.

Field dependent response of magnetorheological elastomers utilizing spherical Fe particles versus Fe nanowires

International Nuclear Information System (INIS)

Song, H J; Wereley, N M; Bell, R C; Planinsek, J L; II, J A Filer

2009-01-01

This study compares the dynamic response of nanowire-based magnetorheological elastomers (MREs), to those containing conventional spherical particles. MRE samples were fabricated by curing the iron particle laden elastomeric material in a magnetic field. Material characteristics of the MRE samples were evaluated using a material test machine that was modified to measure static and frequency dependent characteristics of these samples under different magnetic fields. The MRE samples consisted of a silicone rubber matrix containing various weight fractions of iron particles of differing morphology. Nanowires were used to enhance the interaction forces and contact area between particles. The static and dynamic properties of the MREs were evaluated under a compressive load for the various compositions and weight fractions. The stress vs. strain characteristics were measured for each sample. The equivalent damping coefficient of the MRE samples was measured and characterized under magnetic fields of differing intensities. The dynamic characteristic (dynamic stiffness) was measured under sinusoidal excitation in the frequency domain.

Interfacial Properties of EXXPRO(TM) and General Purpose Elastomers

Science.gov (United States)

Zhang, Y.; Rafailovich, M.; Sokolov, Jon; Qu, S.; Ge, S.; Ngyuen, D.; Li, Z.; Peiffer, D.; Song, L.; Dias, J. A.; McElrath, K. O.

1998-03-01

EXXPRO(Trademark) elastomers are used for tires and many other applications. This elastomer (denoted as BIMS) is a random copolymer of p-methylstyrene (MS) and polyisobutylene (I) with varying degrees of PMS content and bromination (B) on the p-methyl group. BIMS is impermeable to gases, and has good heat, ozone and flex resistance. Very often general purpose elastomers are blended with BIMS. The interfacial width between polybutadiene and BIMS is a sensitive function of the Br level and PMS content. By neutron reflectivity (NR), we studied the dynamics of interface formation as a function of time and temperature for BIMS with varying degrees of PMS and Br. We found that in addition to the bulk parameters, the total film thickness and the proximity of an interactive surface can affect the interfacial interaction rates. The interfacial properties can also be modified by inclusion of particles, such as carbon black (a filler component in tire rubbers). Results will be presented on the relation between the interfacial width as measured by NR and compatibilization studies via AFM and LFM.

Blended Polyurethane and Tropoelastin as a Novel Class of Biologically Interactive Elastomer

Science.gov (United States)

Wise, Steven G.; Liu, Hongjuan; Yeo, Giselle C.; Michael, Praveesuda L.; Chan, Alex H.P.; Ngo, Alan K.Y.; Bilek, Marcela M.M.; Bao, Shisan

2016-01-01

Polyurethanes are versatile elastomers but suffer from biological limitations such as poor control over cell attachment and the associated disadvantages of increased fibrosis. We address this problem by presenting a novel strategy that retains elasticity while modulating biological performance. We describe a new biomaterial that comprises a blend of synthetic and natural elastomers: the biostable polyurethane Elast-Eon and the recombinant human tropoelastin protein. We demonstrate that the hybrid constructs yield a class of coblended elastomers with unique physical properties. Hybrid constructs displayed higher elasticity and linear stress–strain responses over more than threefold strain. The hybrid materials showed increased overall porosity and swelling in comparison to polyurethane alone, facilitating enhanced cellular interactions. In vitro, human dermal fibroblasts showed enhanced proliferation, while in vivo, following subcutaneous implantation in mice, hybrid scaffolds displayed a reduced fibrotic response and tunable degradation rate. To our knowledge, this is the first example of a blend of synthetic and natural elastomers and is a promising approach for generating tailored bioactive scaffolds for tissue repair. PMID:26857114

BioComponent Robots

Science.gov (United States)

2014-02-13

to the bottom of a Petri-dish that had previously been coated with a thin layer of Sylgard 184 silicone elastomer (Dow Corning , Midland, MI...coated with Mann Ease Release 200 mold release spray. Sylgard 184 silicone elastomer (PDMS, Dow Corning , Midland, MI) was prepared according to the...Triangle Park, NC 27709-2211 cell-based actuators, biostability, robot, elastomer films, silk , fibroin, thin films REPORT DOCUMENTATION PAGE 11

Theory of Dielectric Elastomers

Science.gov (United States)

2010-10-25

feature of life is to receive and process information from the environment, and then move. The movements are responsible for diverse functions, far...beyond the function of going from place to place. For example, an octopus can change its color at an astonishing speed, for camouflage and signaling...in engineering are indeed apt in mimicking the salient feature of life: movements in response to stimuli. An electric field can cause an elastomer

African Americans in Oral and Maxillofacial Surgery: Factors Affecting Career Choice, Satisfaction, and Practice Patterns.

Science.gov (United States)

Criddle, Thalia-Rae; Gordon, Newton C; Blakey, George; Bell, R Bryan

2017-12-01

There are few data available on the experience of minority surgeons in the field of oral and maxillofacial surgery (OMS). Therefore, the purpose of this study was to 1) explore factors that contribute to African Americans choosing OMS as a career, 2) examine satisfaction among minority oral and maxillofacial surgeons with the residency application and training process, 3) report on practice patterns among minority oral and maxillofacial surgeons, and 4) identify perceived bias for or against minority oral and maxillofacial surgeons in an attempt to aid the efforts of OMS residency organizations to foster diversity. A 19-item survey was sent to 80 OMS practitioners by use of information from the mailing list of the National Society of Oral and Maxillofacial Surgeons, an American Association of Oral and Maxillofacial Surgeons-affiliated organization. All surveys were sent by mail and were followed by a reminder mailing after 8 weeks. Responses returned within 16 weeks were accepted for analysis. Of the 80 mailed surveys, 41 were returned within the 16-week parameter, representing a return rate of 51%. Most of the minority surgeon respondents were married men with a mean age of 60 years who worked as private practitioners. Most respondents practiced on the eastern and western coasts of the United States. Exposure in dental school was the most important factor in selecting OMS as a specialty. Location and prestige were the most important factors in selecting a residency program. Most respondents reported that race did not affect the success of their application to a residency program and did not currently affect the success of their practice. However, 25 to 46% of participants experienced race-related harassment, and 48 to 55% of participants believed there was a bias against African Americans in OMS. Our data suggest that a substantial number of minority oral and maxillofacial surgeons subjectively perceive race-based bias in their career, although it does not

Magnetically-tunable rebound property for variable elastic devices made of magnetic elastomer and polyurethane foam

Science.gov (United States)

Oguro, Tsubasa; Endo, Hiroyuki; Kawai, Mika; Mitsumata, Tetsu

2017-12-01

A device consisting of a phase of magnetic elastomer, a phase of polyurethane foam (PUF), and permanent magnet was fabricated and the stress-strain curves for the two-phase magnetic elastomer were measured by a uniaxial compression measurement. A disk of magnetic elastomer was adhered on a disk of PUF by an adhesive agent. The PUF thickness was varied from 1 mm to 5 mm while the thickness of magnetic elastomers was constant at 5 mm. The stress at a strain of 0.15 for the two-phase magnetic elastomers was evaluated in the absence and in the presence of a magnetic field of 410 mT. The stress at 0 mT decreased remarkably with the PUF thickness due to the deformation of the PUF phase. On the other hand, the stress at 410 mT slightly decreased with the thickness; however, it kept high values even at high thickness. When the PUF thickness was 5 mm, the maximum stress increment with 45 times to the off-field stress was observed. An experiment using ping-pong balls demonstrated that the coefficient of restitution for the two-phase magnetic elastomers can be dramatically altered by the magnetic field.

Application of silicone based elastomers for manufacturing of Green Fiber Bottle

DEFF Research Database (Denmark)

Saxena, Prateek; Bissacco, Giuliano

2017-01-01

-stageprocess, where the wood fibers are first thermoformed in the desired shape followed by drying of theformed geometry [2]. To ensure the robustness of the bottle and to avoid shrinkage of cellulose fibers,the wet-formed bottle is pressurized using a silicone core. The core is inserted inside the drying tooland......). To simulate the inflation action of the core, Yeoh’s model is used for modelling of W. Thestrength of the GFB is correlated with the pressure the bottle can hold and the cut off burst pressurefrom experiments is also reported in this work....

Development of procedures for calculating stiffness and damping of elastomers in engineering applications, part 7

Science.gov (United States)

Rieger, A.; Zorzi, E.

1980-01-01

An elastomer shear damper was designed, tested, and compared with the performance of the T 55 power turbine supported on the production engine roller bearing support. The Viton 70 shear damper was designed so that the elastomer damper could be interchanged with the production T 55 power turbine roller bearing support. The results show that the elastomer sheer dampener permitted stable operation of the power turbine to the maximum operating speed of 16,000 rpm.

Reporting of ethical protection in recent oral and maxillofacial surgery research involving human subjects.

Science.gov (United States)

Pitak-Arnnop, P; Sader, R; Hervé, C; Dhanuthai, K; Bertrand, J-Ch; Hemprich, A

2009-07-01

This retrospective observational study investigated the frequency of reporting ethical approval and informed consent in recently published oral and maxillofacial surgery (OMS) research involving human subjects. All research involving human subjects published in the International Journal of Oral and Maxillofacial Surgery, Journal of Oral and Maxillofacial Surgery, British Journal of Oral and Maxillofacial Surgery, and Journal of Cranio-Maxillofacial Surgery during January to June 2005-2007 were analysed for disclosure of ethical approval by a local ethical committee and obtaining informed consent from the subjects. 534 articles were identified; ethical approval was documented in 118 (22%) and individual patient consent in 135 (25%). 355 reports (67%) did not include a statement on ethical approval or informed consent and only 74 reports (14%) disclosed statements of both. Ethical documentation in retrospective and observational studies was scant; 12% of randomised controlled trials and 38% of non-random trials did not report both of ethical protections. Most recent OMS publications involving humans failed to mention ethical review or subjects' consent. Authors must adhere to the international research ethics guidelines and journal instructions, while editors should play a gatekeeper role to protect research participants, uphold scientific integrity and maintain public trust in the experimental process and OMS profession.

The Use of Telemedicine in Oral and Maxillofacial Surgery.

Science.gov (United States)

Wood, Eric W; Strauss, Robert A; Janus, Charles; Carrico, Caroline K

2016-04-01

To determine the perceived utility and demand for the application of telemedicine for improved patient care between nonsurgical dental practitioners (GPs) and oral and maxillofacial surgeons (OMS). Two distinct questionnaires were made, one for GPs and one for OMSs. The GP questionnaire was sent to practicing Virginia Dental Association members on an e-mail list (approximately 2,200). The OMS questionnaire was sent by the Virginia Society of Oral Maxillofacial Surgery to members on an e-mail list (approximately 213). Questionnaires included questions about access to care, benefits of telemedicine consultations, reliability of telemedicine consultations, and perceived barriers against and opportunities for the implementation of telemedicine. The questionnaire was completed by 226 GP and 41 OMS respondents. There was a significant difference among responses of GPs based on practice location: rural patients had a longer average time from referral to OMS consultation (P = .003), rural patients traveled longer distances (P telemedicine, whereas OMS respondents were more neutral. GPs responded they would refer more patients (4.4) if consultations could be performed by telemedicine. OMSs agreed that more referrals would influence their decision to provide telemedicine consultations (51%). Practitioners had neutral perceptions about the reliability of telemedicine. OMS respondents agreed they would implement telemedicine in their practice if it provided equally good consultations as in-office visits. According to the present findings, telemedicine could be an important step in the right direction for overcoming current issues with patient access to care and increasing health care costs. The benefits of telemedicine technology have been documented and will continue to be seen with wider application of its use in other areas of health care such as oral and maxillofacial surgery. Copyright © 2016 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier

Manufacturing of Liquid-Embedded Elastomers for Stretchable Electronics

Science.gov (United States)

Kramer, Rebecca; Majidi, Carmel; Weaver, James; Wood, Robert

2013-03-01

Future generations of robots, electronics, and assistive medical devices will include systems that are soft, elastically deformable, and may adapt their functionality in unstructured environments. This will require soft active materials for power circuits and sensing of deformation and contact pressure. As the demand for increased elasticity of electrical components heightens, the challenges for functionality revert to basic questions of fabrication, materials, and design. Several designs for soft sensory skins (including strain, pressure and curvature sensors) based on a liquid-embedded-elastomer approach have been developed. This talk will highlight new ``soft MEMS'' manufacturing techniques based on wetting behavior between gallium-indium alloys and elastomers with varying microtextured surface topography. Supported by Harvard MRSEC and the Wyss Institute

Soft Elasticity in Main Chain Liquid Crystal Elastomers

Directory of Open Access Journals (Sweden)

Anselm C. Griffin

2013-06-01

Full Text Available Main chain liquid crystal elastomers exhibit several interesting phenomena, such as three different regimes of elastic response, unconventional stress-strain relationship in one of these regimes, and the shape memory effect. Investigations are beginning to reveal relationships between their macroscopic behavior and the nature of domain structure, microscopic smectic phase structure, relaxation mechanism, and sample history. These aspects of liquid crystal elastomers are briefly reviewed followed by a summary of the results of recent elastic and high-resolution X-ray diffraction studies of the shape memory effect and the dynamics of the formation of the smectic-C chevron-like layer structure. A possible route to realizing auxetic effect at molecular level is also discussed.

MAXILLOFACIAL SOFT TISSUE INJURIES IN NAIROBI, KENYA

African Journals Online (AJOL)

2012-09-09

Sep 9, 2012 ... Conclusion: The leading causes of MF-STIs apparently differ from those of skeletal fractures. INTRODUCTION. Maxillofacial (MF) soft tissue injuries (STIs) are often overlooked in clinical surveys compared to fractures, yet these injuries negatively impact both on function and esthetics. Previous surveys on ...

American Society of Maxillofacial Surgeons 2006 to 2016: Another Decade of Excellence in Education and Research.

Science.gov (United States)

Doumit, Gaby; Totonchi, Ali; Wexler, Andy; Gosain, Arun K

2017-09-01

Over the past 10 years, the American Society of Maxillofacial Surgeons (ASMS) has continued to advance to meet its mission of being the premier organization to represent maxillofacial and pediatric plastic surgery in the United States. These advances are focused on education of its members, to include the American Society of Maxillofacial Surgeons basic course, the preconference symposium, the annual meeting, two basic maxillofacial courses per year, advanced maxillofacial courses, a boot camp for craniofacial fellows, a cleft course, quarterly webinars, sponsored fellowships, a visiting professorship, and the ASMS journal. In addition, the ASMS has continued to advance as the premier national organization representing maxillofacial and pediatric plastic surgery in the United States, thereby positioning the organization as a primary advocate for these surgical specialties. Outreach of the ASMS has grown over the past decade and now includes representatives to the American Society of Plastic Surgeons/Plastic Surgery Foundation, the American Board of Plastic Surgeons, the American Medical Association, and most recently a seat as a governor with the American College of Surgeons. The ASMS has also initiated an annual Summer Leadership Seminar to explore topics of relevance in a changing health care environment. The present report outlines the major initiatives of the ASMS over the past 10 years.

Airway Management of the Patient with Maxillofacial Trauma: Review of the Literature and Suggested Clinical Approach

Directory of Open Access Journals (Sweden)

Michal Barak

2015-01-01

Full Text Available According to the Advanced Trauma Life Support recommendations for managing patients with life-threatening injuries, securing the airway is the first task of a primary caregiver. Airway management of patients with maxillofacial trauma is complex and crucial because it can dictate a patient’s survival. Securing the airway of patients with maxillofacial trauma is often extremely difficult because the trauma involves the patient’s airway and their breathing is compromised. In these patients, mask ventilation and endotracheal intubation are anticipated to be difficult. Additionally, some of these patients may not yet have been cleared of a cervical spine injury, and all are regarded as having a full stomach and having an increased risk of regurgitation and pulmonary aspiration. The requirements of the intended maxillofacial operation may often preclude the use of an oral intubation tube, and alternative methods for securing the airway should be considered before the start of the surgery. In order to improve the clinical outcome of patients with maxillofacial trauma, cooperation between maxillofacial surgeons, anesthesiologists, and trauma specialists is needed. In this review, we discuss the complexity and difficulties of securing the airway of patients with maxillofacial trauma and present our approach for airway management of such patients.

Rehabilitation of post-traumatic total nasal defect using silicone and acrylic resin

Directory of Open Access Journals (Sweden)

Vikas Aggarwal

2016-01-01

Full Text Available Facial defects resulting from neoplasms, congenital abnormalities or trauma can affect the patient esthetically, psychologically, and even financially. Surgical reconstruction of large facial defects is sometimes not possible and frequently demands prosthetic rehabilitation. For success of such prosthesis, adequate replication of natural anatomy, color matching and blending with tissue interface are important criteria. Variety of materials and retention methods are advocated to achieve a functionally and esthetically acceptable restoration. Silicones are the most commonly used materials because of flexibility, lifelike appearance and ability to be used in combination with acrylic resin which is hard, provides body and helps in achieving retention to the prosthesis by engaging mechanical undercuts. Furthermore, the acrylic portion can be relined easily, thus helping comfortable wear and removal of the prosthesis by patient without traumatizing nasal mucosa. This case report describes time saving and cost effective prosthetic rehabilitation of a patient with total nasal defect using custom sculpted nasal prosthesis made up of silicone elastomer and acrylic resin, which is retained by engaging mechanical undercut and use of biocompatible silicone adhesive.

[Oral maxillofacial-head and neck tumor and holistic integrative medicine].

Science.gov (United States)

Zhang, C P

2017-08-09

The advance of clinical diagnosis and treatment in oral and maxillofacial-head and neck tumors has been through the process of specialization and multidisciplinary cooperation. In most cases, a single discipline cannot meet the requirements of diagnosis and treatment, which needs the cooperation of oral and maxillofacial surgery, otolaryngology and oncology approach and therapeutic method such as surgery, radiotherapy and chemotherapy. Holistic integrative medicine aims at integrating the most effective clinical practice experience and patients' individual situation and prognosis, establishing new medical mode conforming to the modern concept and fulfilling the medical system adapting to the specific characteristics of the diseases.

Development of a novel technique for maxillofacial reconstruction using custom-made bioactive ceramic implants

Science.gov (United States)

Kulbakin, D. E.; Choinzonov, E. L.; Kulkov, S. N.; Buyakova, S. P.; Chernov, V. I.; Mukhamedov, M. R.; Buyakov, A. S.

2017-09-01

Recently, there has been a trend towards the search for new, safe and effective methods of reconstruction of maxillofacial defects after tumor excision. Among various materials used for bone defect reconstruction, ceramics has attached a great deal of attention. The purpose of our study was to develop a technique for personified approach to the reconstruction of maxillofacial bone defects with bioactive ceramic implants. In our study we used the technique of virtual implant planning for maxillofacial reconstruction using preoperative CT data of the patient's facial skeleton. Bioactive ceramic implant materials meet all the requirements for medical materials used in reconstructive surgery. The technique described in this paper to customize prefabricated bioactive ceramic implants enables surgeons to perform reconstruction of large postoperative defects in the maxillofacial region, thereby making custom implants suitable for any patient. The use of this technique decreases surgical time, reduces time needed for postoperative recovery, lowers overall patient morbidity and optimizes aesthetic and functional results.

Synthesis of thermoplastic elastomer using potassium persulfate and ammonium peroxydisulfate initiator

International Nuclear Information System (INIS)

Dewi Sondari; Agus Haryono; M Ghozali; Ahmad Randy; Kuntari Adi Suhardjo; Ariyadi B; Surasno

2010-01-01

Thermoplastic elastomer is polymeric material that has elastomer and thermoplastic properties. This material can be easily molded into finished and recyclable goods, thus environmentally safe for long term application. In this study we synthesize thermoplastic elastomer using two initiator that are potassium persulfate and ammonium peroxydisulfate with natural rubber to monomer (styrene/methyl methacrylate) ratio of 50 : 50 and 60 : 40 (v/v). The process of thermoplastic elastomer synthesis was conducted with emulsion grafting polymerization method for 6 hours at 65 °C. We used sodium dodecyl sulfate as emulsifier. FT-IR analysis result shows that grafting process had already occurred shown by new peaks that were observed in 1743 and 1519 cm"-"1. These peaks was assigned to carbonyl (C=O) group of methyl methacrylate and C=C benzene of styrene respectively. From "1H-NMR new peaks at δ = 7.1 ppm was aromatic proton from phenyl group of styrene, at δ = 3.5 ppm was methoxy proton of grafted methyl methacrylate acrylic group, and at δ = 5.1 ppm that is resonance of isoprene methine proton. This result showed that methyl methacrylate and styrene had already grafted onto natural rubber backbone. Initiator influenced grafting efficiency. Potassium persulfate gave 97.6 % grafting efficiency while ammonium peroxydisulfate gave 90.2 % grafting efficiency. (author)

Incidence and severity of maxillofacial injuries during the Second Lebanon War among Israeli soldiers and civilians.

Science.gov (United States)

Levin, Liran; Zadik, Yehuda; Peleg, Kobi; Bigman, Galya; Givon, Adi; Lin, Shaul

2008-08-01

To analyze the incidence and severity of maxillofacial injuries in the Second Lebanon War, that occurred during the summer of 2006, among Israeli soldiers and civilians. This is a retrospective cohort study of patients recorded in the Israel National Trauma Registry during the Second Lebanon War. Data refer to all general hospitals throughout the country. Data were analyzed according to the etiology of the injury, severity of trauma using the Injury Severity Score, trauma location, and duration of hospital stay. Cases with multiple injuries that included maxillofacial injuries were separated and further analyzed according to the above parameters. Patients with only dental injuries and superficial facial soft tissue lacerations were excluded because they were referred to the military dental clinics and not to general hospitals. Maxillofacial injuries were found in 36 (6.4%) of the 565 wounded. Patients with maxillofacial injuries ranged in age from 20 to 44 years (mean age, 25.5 +/- 5.7 years). Greater than 50% of the injuries required more than 3 hospitalization days. Mortality rate of the maxillofacial injured was 2.8%. Most of the maxillofacial injuries (33; 91.7%) were combined with other organ injuries; 9 (25%) patients also had dental injuries. In the Second Lebanon War, the incidence and severity of true maxillofacial injuries, without dental injuries alone, were relatively low compared with previous reports of other conflicts. However, because most injuries involved multiple organs, special attention is required when planning and providing emergency, as well as secondary and tertiary medical care to war wounded.

Graphene and water-based elastomers thin-film composites by dip-moulding.

Science.gov (United States)

Iliut, Maria; Silva, Claudio; Herrick, Scott; McGlothlin, Mark; Vijayaraghavan, Aravind

2016-09-01

Thin-film elastomers (elastic polymers) have a number of technologically significant applications ranging from sportswear to medical devices. In this work, we demonstrate that graphene can be used to reinforce 20 micron thin elastomer films, resulting in over 50% increase in elastic modulus at a very low loading of 0.1 wt%, while also increasing the elongation to failure. This loading is below the percolation threshold for electrical conductivity. We demonstrate composites with both graphene oxide and reduced graphene oxide, the reduction being undertaken in-situ or ex-situ using a biocompatible reducing agent in ascorbic acid. The ultrathin films were cast by dip moulding. The transparency of the elastomer films allows us to use optical microscopy image and confirm the uniform distribution as well as the conformation of the graphene flakes within the composite.

A Study of Streptococcus Viridans in the Maxillofacial Region

Directory of Open Access Journals (Sweden)

Y. Refoua

2005-12-01

Full Text Available Statement of Problem: Streptococcus viridans is one of the most important microorganisms in the establishment of infections leading to dental caries and heart valve damages. Therefore the diagnosis and prevention of these infections is critical in health care.Purpose: The aim of this in-vivo study was to determine the prevalence of viridans streptococci in abscesses occurring in the maxillofacial region.Materials and Methods: The study sample consisted of 39 patients with maxillofacial abscesses, referred to the Department of Oral Surgery Faculty of Dentistry Tehran University of Medical Sciences and Dr. Shariati Hospital, Tehran University of Medical Sciences. Extra-oral incision, drainage and pus collection followed by culture, staining and biochemical and sugar fermentation tests were carried out for all participants.Results: In the present study %53.84 and 46.16% of the patients had negative and positive culture results, respectively. In the positive culture group, %2.5 of the viridans streptococci were streptococcus salivarius, %4.6 streptococcus sanguis and %17.9 were streptococcus mutans.Conclusion: The findings of this study showed that viridans streptococci are an important factor in the development of metastatic and maxillofacial infections which can pose a significant threat to the patient’s life.

Maxillofacial fractures among patients attended at Muhimbili ...

African Journals Online (AJOL)

Objective: To determine the pattern of occurrence, types, and treatment and prognosis of patients with maxillofacial fractures at the dental school of the Muhimbili University College of Health SciencesNational Hospital, Dar es Salaam, Tanzania. Methodology: ... comprised of 25 (accounting for 21.3%) of the cases (p<0.001).

Dental student perceptions of oral and maxillofacial surgery as a specialty.

Science.gov (United States)

Jarosz, Krystian F; Ziccardi, Vincent B; Aziz, Shahid R; Sue-Jiang, Shuying

2013-05-01

The specialty of oral and maxillofacial surgery (OMS) encompasses the diagnosis and surgical management of a variety of pathologic, functional, and esthetic conditions of the oral and maxillofacial region. Despite the specialty's prominent role in the field of dentistry, a lack of complete understanding still remains among dental and medical health professionals as to the exact scope and expertise of the oral and maxillofacial surgeon. The present study aimed to analyze a population of dental students' perceptions of OMS as a specialty with respect to treatment rendered, referral patterns, and a general opinion of the specialty as a whole. A survey consisting of 10 multiple-choice questions was compiled and distributed to dental students through an on-line polling service (SurveyMonkey). A total of 5 dental student classes at a single dental school were polled using school-based electronic mail, including the graduating seniors. All answers were kept confidential, and no individual students were identified. The students were not able to retake the survey once completed. The final tallies of the survey results were compiled and submitted for statistical analysis. Statistically significant associations between the year of dental education and student perceptions of OMS were determined. As dental students progress through their undergraduate studies, their perceptions change with regard to the referral of dental implants. Periodontists were found to have statistically significantly greater rates of referral than oral and maxillofacial surgeons from dental students in the fourth year and recent graduates compared with younger dental students from the first, second, and third years for placement of dental implants. Statistically insignificant in terms of a changing dental student perception was the finding that third molar removal was within the domain of the oral and maxillofacial surgeon, as well as the management of cleft lip and palate deformities and mandibular

History of the Oral and Maxillofacial Surgery Residency Program at Universidad el Bosque, Bogotá, Colombia.

Science.gov (United States)

Castro-Núñez, Jaime

2012-01-01

The formal training of oral and maxillofacial surgeons in Colombia started in 1958 at Hospital Sanjos6, thanks to the titanic work of Waldemar Wilhelm, a German-born surgeon who settled in BogotA in 1950. Today there are seven institutions in Colombia that offer residency programs in oral and maxillofacial surgery. The aim of this article is to describe the history of the Oral and Maxillofacial Surgery Residency Program at Universidad El Bosque in Bogota.

Are You Ready for Emergency Medical Services in Your Oral and Maxillofacial Surgery Office?

Science.gov (United States)

Rayner, Clive; Ragan, Michael R

2018-05-01

Efficient responses to emergencies in the oral and maxillofacial surgery office require preparation, communication, and thorough documentation of the event and response. The concept of team anesthesia is showcased with these efforts. Emergency medical services training and response times vary greatly. The oral and maxillofacial surgery office should be prepared to manage the patient for at least 15 minutes after making the call to 911. Patient outcomes are optimized when providers work together to manage and transport the patient. Oral and maxillofacial surgery offices should develop and rehearse emergency plans and coordinate these protocols with local Emergency medical services teams. Copyright © 2018 Elsevier Inc. All rights reserved.

Two-way actuation behavior of shape memory polymer/elastomer core/shell composites

International Nuclear Information System (INIS)

Kang, Tae-Hyung; Lee, Jeong-Min; Yu, Woong-Ryeol; Youk, Ji Ho; Ryu, Hee Wook

2012-01-01

Semi-crystalline shape memory polymers (SMPs) show net two-way shape memory (2W-SM) behavior under constant stresses by the recoverable creep strain upon heating and stress-induced crystallization under the application of creep stress upon cooling. The applied constant stress is the key factor in this 2W-SM behavior. A core/shell structure is manufactured for the purpose of imparting a constant stress upon SMPs. An SMP in film or fiber form is dipped into a solution of an elastomer, photoinitiator, and curing agent and then dried out. After this dip coating process is repeatedly carried out, the SMP/elastomer core/shell composite is deformed into a temporary shape after being heated up above the transition temperature of the SMP. Under constant strain conditions, the composite is cooled down, after which the shell elastomer is cured using ultraviolet light. Then, the SMP/elastomer core/shell composite extends and contracts upon cooling and heating, respectively, without any external load. This cyclic deformation behavior is characterized, demonstrating that the current method offers a simple macroscopic processing technique to manufacture 2W-SM polymer composites. (paper)

Hemispherical breathing mode speaker using a dielectric elastomer actuator.

Science.gov (United States)

Hosoya, Naoki; Baba, Shun; Maeda, Shingo

2015-10-01

Although indoor acoustic characteristics should ideally be assessed by measuring the reverberation time using a point sound source, a regular polyhedron loudspeaker, which has multiple loudspeakers on a chassis, is typically used. However, such a configuration is not a point sound source if the size of the loudspeaker is large relative to the target sound field. This study investigates a small lightweight loudspeaker using a dielectric elastomer actuator vibrating in the breathing mode (the pulsating mode such as the expansion and contraction of a balloon). Acoustic testing with regard to repeatability, sound pressure, vibration mode profiles, and acoustic radiation patterns indicate that dielectric elastomer loudspeakers may be feasible.

Experimental study on behaviors of dielectric elastomer based on acrylonitrile butadiene rubber

Science.gov (United States)

An, Kuangjun; Chuc, Nguyen Huu; Kwon, Hyeok Yong; Phuc, Vuong Hong; Koo, Jachoon; Lee, Youngkwan; Nam, Jaedo; Choi, Hyouk Ryeol

2010-04-01

Previously, the dielectric elastomer based on Acrylonitrile Butadiene Rubber (NBR), called synthetic elastomer has been reported by our group. It has the advantages that its characteristics can be modified according to the requirements of performances, and thus, it is applicable to a wide variety of applications. In this paper, we address the effects of additives and vulcanization conditions on the overall performance of synthetic elastomer. In the present work, factors to have effects on the performances are extracted, e.g additives such as dioctyl phthalate (DOP), barium titanium dioxide (BaTiO3) and vulcanization conditions such as dicumyl peroxide (DCP), cross-linking times. Also, it is described how the performances can be optimized by using DOE (Design of Experiments) technique and experimental results are analyzed by ANOVA (Analysis of variance).

Tensile and impact properties of three-component PP/wood/elastomer composites

Directory of Open Access Journals (Sweden)

B. Pukanszky

2012-03-01

Full Text Available Polypropylene (PP was reinforced with wood flour and impact modified with elastomers to increase stiffness and impact resistance simultaneously. Elastomer content changed in four (0, 5, 10 and 20 wt%, while that of wood content in seven steps, the latter from 0 to 60 wt% in 10 wt% steps. Structure and adhesion were controlled by the addition of functionalized (maleated polymers. Composites were homogenized in a twin-screw extruder and then injection molded to tensile bars. Fracture resistance was characterized by standard and instrumented impact tests. The results showed that the components are dispersed independently of each other even when a functionalized elastomer is used for impact modification, at least under the conditions of this study. Impact resistance does not change much as a function of wood content in PP/wood composites, but decreases drastically from the very high level of the PP/elastomer blend to almost the same value obtained without impact modifier in the three-component materials. Increasing stiffness and fiber related local deformation processes led to small fracture toughness at large wood content. Micromechanical deformation processes depend mainly on the strength of PP/wood interaction; debonding and pull-out take place at poor adhesion, while fiber fracture dominates when adhesion is strong. Composites with sufficiently large impact resistance cannot be prepared in the usual range of wood contents (50–60 wt%.

Dielectric elastomer actuators using Slide-Ring Material® with increased permittivity

International Nuclear Information System (INIS)

Tsuchitani, Shigeki; Miki, Hirofumi; Sunahara, Tokiharu

2015-01-01

The inclusion of high permittivity nanoparticles in elastomeric materials for dielectric elastomer actuators (DEAs) is one promising method to achieve large strain at relatively low applied voltages. However, the addition of these nanoparticles tends to increase the stiffness of the elastomer and disturbs the actuation of the DEA. This is attributed to restriction of the chain motion in the elastomer by the nanoparticles. Slide-Ring Material ® (SRM) is a cross-linked polymeric material with freely movable cross-linking sites. The internal stresses in this structure are dramatically homogenized by the pulley effect; therefore, the restriction of chain motion due to the nanoparticles is expected to be significantly reduced. We have employed SRM as a host elastomer for a DEA with the addition of ferroelectric BaTiO 3 (BT) nanoparticles. The effects of BT addition on the permittivity, stiffness and viscosity of the SRM–BT nanocomposites, and the actuation strain of DEAs using SRM were evaluated. The permittivity of the nanocomposites increased linearly with the concentration of BT and reached 3.6 times that for pure SRM at 50 wt%. The elastic modulus and the viscosity remained almost constant up to 20 wt% and then decreased above this concentration. The actuation strain of a planar actuator using SRM and 50 wt% BT was four times larger than that of the DEA with pure SRM. (paper)

Dysocclusion after maxillofacial trauma: a 42 year analysis

NARCIS (Netherlands)

Kommers, S.C.; van den Bergh, B.; Boffano, P.; Verweij, K.P.; Forouzanfar, T.

2014-01-01

Background The aim of this study was to evaluate the surgical management of posttraumatic dysocclusion in the Department of Oral and Maxillofacial Surgery in the VU Medical Centre in Amsterdam. Patients and methods All patients who underwent surgical correction of a posttraumatic dysocclusion

Epidemiologic analysis and evaluation of complications in 1266 cases with maxillofacial trauma

Directory of Open Access Journals (Sweden)

Cenk Demirdover

2018-01-01

Full Text Available Introduction: Patients with maxillofacial trauma represent a major group of patients in plastic surgery practice. These traumas are often caused by in-car and noncar road accidents and can result in permanent damages. This study aims at providing an epidemiologic analysis of such cases together with their diagnostic procedures, treatment methods, and postoperative complications. Materials and Methods: A total of 1266 maxillofacial trauma cases that were operated on between 2003 and 2017 were studied, and analyzed for fractured bones, etiology, diagnosis and treatment principles, and complications. Results: The major etiologic factor causing maxillofacial trauma in our study is noncar road accidents (25.5%. Mandible fractures were seen to be the most common type of bone fracture (52.2%. Together with physical examination, computerized tomography and orthopantomography are the diagnostic procedures we effectively use in our clinic. Rigid and semi-rigid fixation with plate and screws are the most frequently used treatment methods, and complication rates are seen to be lower (by 6.6% than those reported in the literature. Conclusion: Careful and meticulous processes, as well as effective follow-up of the patient are required to achieve optimal esthetic and functional results in maxillofacial trauma cases. Such approach can help to reduce the possibility of complications and allow for their early identification, hence early intervention.

Finite element analysis and validation of dielectric elastomer actuators used for active origami

International Nuclear Information System (INIS)

McGough, Kevin; Ahmed, Saad; Frecker, Mary; Ounaies, Zoubeida

2014-01-01

The field of active origami explores the incorporation of active materials into origami-inspired structures in order to serve as a means of actuation. Active origami-inspired structures capable of folding into complex three-dimensional (3D) shapes have the potential to be lightweight and versatile compared to traditional methods of actuation. This paper details the finite element analysis and experimental validation of unimorph actuators. Actuators are fabricated by adhering layers of electroded dielectric elastomer (3M VHB F9473PC) onto a passive substrate layer (3M Magic Scotch Tape). Finite element analysis of the actuators simulates the electromechanical coupling of the dielectric elastomer under an applied voltage by applying pressures to the surfaces of the dielectric elastomer where the compliant electrode (conductive carbon grease) is present. 3D finite element analysis of the bending actuators shows that applying contact boundary conditions to the electroded region of the active and passive layers provides better agreement to experimental data compared to modeling the entire actuator as continuous. To improve the applicability of dielectric elastomer-based actuators for active origami-inspired structures, folding actuators are developed by taking advantage of localized deformation caused by a passive layer with non-uniform thickness. Two-dimensional analysis of the folding actuators shows that agreement to experimental data diminishes as localized deformation increases. Limitations of using pressures to approximate the electromechanical coupling of the dielectric elastomer under an applied electric field and additional modeling considerations are also discussed. (paper)

Compatibility of elastomers in palm biodiesel

Energy Technology Data Exchange (ETDEWEB)

Haseeb, A.S.M.A.; Masjuki, H.H.; Siang, C.T.; Fazal, M.A. [Department of Mechanical Engineering, University of Malaya, 50603 Kuala Lumpur (Malaysia)

2010-10-15

In recent time, environmental awareness and concern over the rapid exhaustion of fossil fuels have led to an increased popularity of biodiesel as an alternative fuel for automobiles. However, there are concerns over enhanced degradation of automotive materials in biodiesel. The present study aims to investigate the impact of palm biodiesel on the degradation behavior of elastomers such as nitrile rubber (NBR), polychloroprene, and fluoro-viton A. Static immersion tests in B0 (diesel), B10 (10% biodiesel in diesel), B100 (biodiesel) were carried out at room temperature (25 C) and at 50 C for 500 h. At the end of immersion test, degradation behavior was investigated by measuring mass, volume, hardness as well as tensile strength and elongation. The exposed elastomer surface was studied by scanning electron microscopy (SEM). Fourier Transform Infrared (FTIR) spectroscopy was carried out to identify the chemical and structural changes. Results showed that the extent of degradation was higher for both polychloroprene and NBR while fluoro-viton exhibited good resistance to degradation and was least attacked. (author)

Modeling of Magnetostriction of Soft Elastomer

International Nuclear Information System (INIS)

Petr, Andriushchenko; Leonid, Afremov; Mariya, Chernova

2014-01-01

Small magnetic particles placed in a relatively soft polymer (with elastic modulus E ∼ 10 ÷ 100 kPa) are magnetically soft elastomers. The external magnetic field acts on each particle which leads to microscopic deformation of the material and consequently to changing of its shape – magnetostriction. For purposes of studying of magnetostriction the model of movable cellular automata (MCA), in which a real heterogeneous material is an ensemble of interacting elements of finite size – automata, is used. It's supposed to be that the motion of each automata can be described by Newton's Second law. The force acting on the i-th automata consists of the following components: volume-dependent force acting on the automata i which is caused by pressure from the surrounding automata; force of an external magnetic field acting on the i-th automata with some magnetic moment; and normal and tangential interaction force between a pair of i and j automata. This approach was used for modeling of magnetostriction elastomer

The shape-memory effect in ionic elastomers: fixation through ionic interactions.

Science.gov (United States)

González-Jiménez, Antonio; Malmierca, Marta A; Bernal-Ortega, Pilar; Posadas, Pilar; Pérez-Aparicio, Roberto; Marcos-Fernández, Ángel; Mather, Patrick T; Valentín, Juan L

2017-04-19

Shape-memory elastomers based on a commercial rubber cross-linked by both ionic and covalent bonds have been developed. The elastomeric matrix was a carboxylated nitrile rubber (XNBR) vulcanized with magnesium oxide (MgO) providing ionic interactions that form hierarchical structures. The so-named ionic transition is used as the unique thermal transition responsible for the shape-memory effect (SME) in these elastomers. These ionic interactions fix the temporary shape due to their behavior as dynamic cross-links with temperature changes. Covalent cross-links were incorporated with the addition of different proportions of dicumyl peroxide (DCP) to the ionic elastomer to establish and recover the permanent shape. In this article, the SME was modulated by modifying the degree of covalent cross-linking, while keeping the ionic contribution constant. In addition, different programming parameters, such as deformation temperature, heating/cooling rate, loading/unloading rate and percentage of tensile strain, were evaluated for their effects on shape-memory behavior.

Thermoplastic elastomers via controlled radical graft polymerization

NARCIS (Netherlands)

Tuzcu, G.

2012-01-01

Rubbery behavior with a consistent modulus over a wide temperature range is a challenge in the search for ultimate structure-property relations of thermoplastic elastomers (TPEs). This feature is closely related to the phase separation behavior of the constitutional segments and the Tg of the

Iterative and variational homogenization methods for filled elastomers

Science.gov (United States)

Goudarzi, Taha

Elastomeric composites have increasingly proved invaluable in commercial technological applications due to their unique mechanical properties, especially their ability to undergo large reversible deformation in response to a variety of stimuli (e.g., mechanical forces, electric and magnetic fields, changes in temperature). Modern advances in organic materials science have revealed that elastomeric composites hold also tremendous potential to enable new high-end technologies, especially as the next generation of sensors and actuators featured by their low cost together with their biocompatibility, and processability into arbitrary shapes. This potential calls for an in-depth investigation of the macroscopic mechanical/physical behavior of elastomeric composites directly in terms of their microscopic behavior with the objective of creating the knowledge base needed to guide their bottom-up design. The purpose of this thesis is to generate a mathematical framework to describe, explain, and predict the macroscopic nonlinear elastic behavior of filled elastomers, arguably the most prominent class of elastomeric composites, directly in terms of the behavior of their constituents --- i.e., the elastomeric matrix and the filler particles --- and their microstructure --- i.e., the content, size, shape, and spatial distribution of the filler particles. This will be accomplished via a combination of novel iterative and variational homogenization techniques capable of accounting for interphasial phenomena and finite deformations. Exact and approximate analytical solutions for the fundamental nonlinear elastic response of dilute suspensions of rigid spherical particles (either firmly bonded or bonded through finite size interphases) in Gaussian rubber are first generated. These results are in turn utilized to construct approximate solutions for the nonlinear elastic response of non-Gaussian elastomers filled with a random distribution of rigid particles (again, either firmly

Patterns, Severity, and Management of Maxillofacial Injuries in a ...

African Journals Online (AJOL)

exposure.[3]. The changing etiological factors and patterns of maxillofacial injuries reported .... Ivy and Curtis[13] system while maxillary fractures were classified .... diligence and compliance to keep a good oral hygiene and prevent infection.

Numerical study of liquid crystal elastomers by a mixed finite element method

KAUST Repository

LUO, C.

2011-08-22

Liquid crystal elastomers present features not found in ordinary elastic materials, such as semi-soft elasticity and the related stripe domain phenomenon. In this paper, the two-dimensional Bladon-Terentjev-Warner model and the one-constant Oseen-Frank energy expression are combined to study the liquid crystal elastomer. We also impose two material constraints, the incompressibility of the elastomer and the unit director norm of the liquid crystal. We prove existence of minimiser of the energy for the proposed model. Next we formulate the discrete model, and also prove that it possesses a minimiser of the energy. The inf-sup values of the discrete linearised system are then related to the smallest singular values of certain matrices. Next the existence and uniqueness of the Lagrange multipliers associated with the two material constraints are proved under the assumption that the inf-sup conditions hold. Finally numerical simulations of the clamped-pulling experiment are presented for elastomer samples with aspect ratio 1 or 3. The semi-soft elasticity is successfully recovered in both cases. The stripe domain phenomenon, however, is not observed, which might be due to the relative coarse mesh employed in the numerical experiment. Possible improvements are discussed that might lead to the recovery of the stripe domain phenomenon. © Copyright Cambridge University Press 2011.

Seismic performance evaluation of an MR elastomer-based smart base isolation system using real-time hybrid simulation

International Nuclear Information System (INIS)

Eem, S H; Jung, H J; Koo, J H

2013-01-01

Recently, magneto-rheological (MR) elastomer-based base isolation systems have been actively studied as alternative smart base isolation systems because MR elastomers are capable of adjusting their modulus or stiffness depending on the magnitude of the applied magnetic field. By taking advantage of the MR elastomers’ stiffness-tuning ability, MR elastomer-based smart base isolation systems strive to alleviate limitations of existing smart base isolation systems as well as passive-type base isolators. Until now, research on MR elastomer-based base isolation systems primarily focused on characterization, design, and numerical evaluations of MR elastomer-based isolators, as well as experimental tests with simple structure models. However, their applicability to large civil structures has not been properly studied yet because it is quite challenging to numerically emulate the complex behavior of MR elastomer-based isolators and to conduct experiments with large-size structures. To address these difficulties, this study employs the real-time hybrid simulation technique, which combines physical testing and computational modeling. The primary goal of the current hybrid simulation study is to evaluate seismic performances of an MR elastomer-based smart base isolation system, particularly its adaptability to distinctly different seismic excitations. In the hybrid simulation, a single-story building structure (non-physical, computational model) is coupled with a physical testing setup for a smart base isolation system with associated components (such as laminated MR elastomers and electromagnets) installed on a shaking table. A series of hybrid simulations is carried out under two seismic excitations having different dominant frequencies. The results show that the proposed smart base isolation system outperforms the passive base isolation system in reducing the responses of the structure for the excitations considered in this study. (paper)

A micro-macro constitutive model for finite-deformation viscoelasticity of elastomers with nonlinear viscosity

Science.gov (United States)

Zhou, Jianyou; Jiang, Liying; Khayat, Roger E.

2018-01-01

Elastomers are known to exhibit viscoelastic behavior under deformation, which is linked to the diffusion processes of the highly mobile and flexible polymer chains. Inspired by the theories of polymer dynamics, a micro-macro constitutive model is developed to study the viscoelastic behaviors and the relaxation process of elastomeric materials under large deformation, in which the material parameters all have a microscopic foundation or a microstructural justification. The proposed model incorporates the nonlinear material viscosity into the continuum finite-deformation viscoelasticity theories which represent the polymer networks of elastomers with an elastic ground network and a few viscous subnetworks. The developed modeling framework is capable of adopting most of strain energy density functions for hyperelastic materials and thermodynamics evolution laws of viscoelastic solids. The modeling capacity of the framework is outlined by comparing the simulation results with the experimental data of three commonly used elastomeric materials, namely, VHB4910, HNBR50 and carbon black (CB) filled elastomers. The comparison shows that the stress responses and some typical behaviors of filled and unfilled elastomers can be quantitatively predicted by the model with suitable strain energy density functions. Particularly, the strain-softening effect of elastomers could be explained by the deformation-dependent (nonlinear) viscosity of the polymer chains. The presented modeling framework is expected to be useful as a modeling platform for further study on the performance of different type of elastomeric materials.

Cross-Linked Liquid Crystalline Systems From Rigid Polymer Networks to Elastomers

CERN Document Server

Broer, Dirk

2011-01-01

With rapidly expanding interest in liquid crystalline polymers and elastomers among the liquid crystal community, researchers are currently exploring the wide range of possible application areas for these unique materials, including optical elements on displays, tunable lasers, strain gauges, micro-structures, and artificial muscles. Written by respected scientists from academia and industry around the world, who are not only active in the field but also well-known in more traditional areas of research, "Cross-Linked Liquid Crystalline Systems: From Rigid Polymer Networks to Elastomers&qu

Accuracy of secondary maxillofacial reconstruction with prefabricated fibula grafts using 3D planning and guided reconstruction

NARCIS (Netherlands)

Schepers, Rutger H.; Kraeima, Joep; Vissink, Arjan; Lahoda, Lars U.; Roodenburg, Jan L. N.; Reintsema, Harry; Raghoebar, Gerry M.; Witjes, Max J.

Background: We compared the pre-operative 3D-surgical plan with the surgical outcome of complex two-stage secondary reconstruction of maxillofacial defects using inserted implants in the prefabricated fibula graft. Methods: Eleven reconstructions of maxillofacial defects with prefabricated fibulas

A survey on dielectric elastomer actuators for soft robots.

Science.gov (United States)

Gu, Guo-Ying; Zhu, Jian; Zhu, Li-Min; Zhu, Xiangyang

2017-01-23

Conventional industrial robots with the rigid actuation technology have made great progress for humans in the fields of automation assembly and manufacturing. With an increasing number of robots needing to interact with humans and unstructured environments, there is a need for soft robots capable of sustaining large deformation while inducing little pressure or damage when maneuvering through confined spaces. The emergence of soft robotics offers the prospect of applying soft actuators as artificial muscles in robots, replacing traditional rigid actuators. Dielectric elastomer actuators (DEAs) are recognized as one of the most promising soft actuation technologies due to the facts that: i) dielectric elastomers are kind of soft, motion-generating materials that resemble natural muscle of humans in terms of force, strain (displacement per unit length or area) and actuation pressure/density; ii) dielectric elastomers can produce large voltage-induced deformation. In this survey, we first introduce the so-called DEAs emphasizing the key points of working principle, key components and electromechanical modeling approaches. Then, different DEA-driven soft robots, including wearable/humanoid robots, walking/serpentine robots, flying robots and swimming robots, are reviewed. Lastly, we summarize the challenges and opportunities for the further studies in terms of mechanism design, dynamics modeling and autonomous control.

Statistical analysis of magnetically soft particles in magnetorheological elastomers

Science.gov (United States)

Gundermann, T.; Cremer, P.; Löwen, H.; Menzel, A. M.; Odenbach, S.

2017-04-01

The physical properties of magnetorheological elastomers (MRE) are a complex issue and can be influenced and controlled in many ways, e.g. by applying a magnetic field, by external mechanical stimuli, or by an electric potential. In general, the response of MRE materials to these stimuli is crucially dependent on the distribution of the magnetic particles inside the elastomer. Specific knowledge of the interactions between particles or particle clusters is of high relevance for understanding the macroscopic rheological properties and provides an important input for theoretical calculations. In order to gain a better insight into the correlation between the macroscopic effects and microstructure and to generate a database for theoretical analysis, x-ray micro-computed tomography (X-μCT) investigations as a base for a statistical analysis of the particle configurations were carried out. Different MREs with quantities of 2-15 wt% (0.27-2.3 vol%) of iron powder and different allocations of the particles inside the matrix were prepared. The X-μCT results were edited by an image processing software regarding the geometrical properties of the particles with and without the influence of an external magnetic field. Pair correlation functions for the positions of the particles inside the elastomer were calculated to statistically characterize the distributions of the particles in the samples.

Portfolio: A Comprehensive Method of Assessment for Postgraduates in Oral and Maxillofacial Surgery

OpenAIRE

Kadagad, Poornima; Kotrashetti, S. M.

2012-01-01

Post graduate learning and assessment is an important responsibility of an academic oral and maxillofacial surgeon. The current method of assessment for post graduate training include formative evaluation in the form of seminars, case presentations, log books and infrequently conducted end of year theory exams. End of the course theory and practical examination is a summative evaluation which awards the degree to the student based on grades obtained. Oral and maxillofacial surgery is mainly a...

Treatment cost of patients with maxillofacial fractures at the University Hospital in Mostar 2002-2006.

Science.gov (United States)

Jurić, Mario; Novakovic, Josip; Carapina, Mirela; Kneiević, Ervin

2010-03-01

The aim of this study was to establish the costs structure of medical treatment for the patients with maxillofacial fractures, to perform a treatment cost evaluation, describe the factors which considerably influence the costs and discover the ways of achieving financial savings in treated patients. The study group consisted of patients with maxillofacial fractures who were admitted and treated at the Department of Maxillofacial Surgery of the University Hospital Mostar in the period from January 2002 until December 2006. Data for the study were collected from the patients' databases, case histories and data obtained on the basis of individual payments for the treatment that was collected by Finance Department of the University Hospital of Mostar Most patients in this study were men (83%), of average age 34 +/- 19 years. Zygomatic bone fracture was the commonest injury. Open surgical procedure was performed in 84.7% of treated cases. The costs for the open procedure were considerably higher than conservative treatment. Medication cost made up a total of 37.9% and cost of hospital accommodation 27.3% out of total hospital charge. Cost reduction in treated patients with maxillofacial fractures should be achieved through protocols of urgent treatment of maxillofacial trauma patients immediately after sustaining an injury and with earlier discharge of the patients when postoperative complications are not expected.

[Percutaneous maxillary nerve block anesthesia in maxillofacial surgery].

Science.gov (United States)

Robiony, M; Demitri, V; Costa, F; Politi, M

1999-01-01

Personal experience in percutaneous maxillary nerve block anesthesia in association with transmucosal anesthesia of the sphenopalatine ganglion in oral and maxillofacial surgery, is presented. Six Caldwell-Luc, 9 anthrotomies and biopsies of maxillary sinus, 8 removals of extensive odontogenic cysts and 12 surgical maxillary expansions were performed from 1994 to 1996 at our Department. Maxillary transcutaneous nerve block in association with transmucosal anesthesia of the sphenopalatine ganglion were performed. Carbocaine without adrenaline in association with NaCO3 1/10 for maxillary nerve block anesthesia and lidocaineoprilocaine cream (EMLA) for transmucosal anesthesia were employed. Intra- and post-operative pain were evaluated by visual analogue scale in all the patients. Anesthesiological procedures revealed to be effective in all surgical interventions and postoperative analgesia allowed easier pain control. The simplicity of execution, the effective pre- and postoperative anesthesia and the absence of side effects make this procedure particularly indicated in oral and maxillofacial surgery.

Experimental investigation of torsional vibration isolation using Magneto Rheological Elastomer

Directory of Open Access Journals (Sweden)

Praveen Shenoy K

2018-01-01

Full Text Available Rotating systems suffer from lateral and torsional vibrations which have detrimental effect on the roto-dynamic performance. Many available technologies such as vibration isolators and vibration absorbers deal with the torsional vibrations to a certain extent, however passive isolators and absorbers find less application when the input conditions are dynamic. The present work discusses use of a smart material called as Magneto Rheological Elastomer (MRE, whose properties can be changed based on magnetic field input, as a potential isolator for torsional vibrations under dynamic loading conditions. Carbonyl Iron Particles (CIP of average size 5 μm were mixed with RTV Silicone rubber to form the MRE. The effect of magnetic field on the system parameters was comprehended under impulse loading conditions using a custom built in-house system. Series arrangement of accelerometers were used to differentiate between the torsional and the bending modes of vibration of the system. Impact hammer tests were carried out on the torsional system to study its response, in the presence and absence of magnetic field. The tests revealed a shift in torsional frequency in the presence of magnetic field which elucidates the ability of MRE to work as a potential vibration isolator for torsional systems.

Eliminating electromechanical instability in dielectric elastomers by employing pre-stretch

International Nuclear Information System (INIS)

Jiang, Liang; Jerrams, Stephen; Betts, Anthony; Kennedy, David

2016-01-01

Electromechanical instability (EMI) is one of most common failure modes for dielectric elastomers (DEs). It has been reported that pre-stretching a DE sample can suppress EMI due to strain stiffening taking place for larger strains and a higher elastic modulus are achieved at high stretch ratios when a voltage is applied to the material. In this work, the influence of equi-biaxial stretch on DE secant modulus was studied using VHB 4910 and silicone rubber (SR) composites containing barium titanate (BaTiO 3 , BT) particles and also dopamine coated BT (DP-BT) particles. The investigation of equi-biaxial deformation and EMI failure for VHB 4910 was undertaken by introducing a voltage-stretch function. The results showed that EMI was suppressed by equi-biaxial pre-stretch for all the DEs fabricated and tested. The stiffening properties of the DE materials were also studied with respect to the secant modulus. Furthermore, a voltage-induced strain of above 200% was achieved for the polyacrylate film by applying a pre-stretch ratio of 2.0 without EMI occurring. However, a maximum voltage-induced strain in the polyacrylate film of 78% was obtained by the SR/20 wt% DP-BT composite for a lower applied pre-stretch ratio of 1.6 and again EMI was eliminated. (paper)

Weibull Analysis of Electrical Breakdown Strength as an Effective Means of Evaluating Elastomer Thin Film Quality

DEFF Research Database (Denmark)

Silau, Harald; Stabell, Nicolai Bogø; Petersen, Frederik Riddersholm

2018-01-01

To realize the commercial potential of dielectric elastomers, reliable, large-scale film production is required. Ensuring proper mixing and subsequently avoiding demixing after, for example, pumping and coating of elastomer premix in an online process is not facile. Weibull analysis...... of the electrical breakdown strength of dielectric elastomer films is shown to be an effective means of evaluating the film quality. The analysis is shown to be capable of distinguishing between proper and improper mixing schemes where similar analysis of ultimate mechanical properties fails to distinguish....

Intra‑Operative Airway Management in Patients with Maxillofacial ...

African Journals Online (AJOL)

the surgeon and the anesthetist is naturally a challenge for both specialists. In addition to this, when traumatic maxillofacial injury results in the disruption of the normal anatomy from edema or structural damage to tissues, bleeding, unstable skeletal structures, and foreign bodies that can interfere with instrumentation or ...

Maxillectomy defects - to reconstruct or not? Pilot survey of Nigerian oral and maxillofacial surgeons

Directory of Open Access Journals (Sweden)

Abdurrazaq Olanrewaju Taiwo

2017-01-01

Full Text Available Background: The choice of reconstruction options for maxillectomy defects varies significantly. Factors affecting it range from the type of defect to the surgeon's expertise. This study aims to evaluate the practice of Nigerian Oral and Maxillofacial surgeons in the reconstruction of post-maxillectomy defects. Materials and Methods: The survey was conducted by use of questionnaires administered at the annual scientific meeting of the oral and maxillofacial surgeons of Nigeria in Ibadan 2012. Results: A response rate of 66.7% was achieved. All of our respondents are consultant oral and maxillofacial surgeons, 80% of whom practice in a teaching hospital. All but one of them perform maxillectomies, however only 25% of them offer surgical reconstruction of the resulting defects to patients. Flaps have been used by 25% of the respondents, while none of them has employed microvascular reconstruction. Prosthetic rehabilitation of patients is pervasive among the respondents. Conclusion: Maxillectomy defects have far-reaching consequences on patients' quality of life and attempts should be made to reconstruct such defects. Although maxillectomy is a commonly performed procedure among oral and maxillofacial surgeons in Nigeria, especially for malignancies of the oral and paranasal sinuses, surgical reconstruction of resulting defects is not so frequently done. Microvascular surgery, which is becoming a frequently utilized option among surgeons in developed nations, is still infrequently used in our environment. There is a need for oral and maxillofacial surgeons in our climes to improve their skills so as to increase the range of reconstructive options offered.

Towards holonomic electro-elastomer actuators with six degrees of freedom

International Nuclear Information System (INIS)

Conn, A T; Rossiter, J

2012-01-01

Functionally efficient six degree of freedom (DOF) actuators have not yet been developed in a scale-invariant and inherently compliant unified form. This has primarily been due to the use of conventional serial or parallel kinematical configurations and electromagnetic motors, pneumatics and hydraulics. Contrary to traditional technologies, utilizing electro-active elastomers enables multi-DOF actuation and holonomic operation with minimal structural complexity. Conical dielectric elastomer actuators (DEAs) are compact multi-DOF actuator–sensors that are scalable and can be entirely polymeric, making them suitable for a variety of applications including minimally invasive medical devices. In this paper, cone DEAs are developed towards integrated 6-DOF actuation with muscle-like performance from a single structure. This is achieved by demonstrating the feasibility of holonomic 6-DOF actuation and through experimental characterization of a 5-DOF prototype. The 5-DOF prototype (50 mm length, 60 mm diameter) produced rotational actuation outputs of ±21.7° and ±9.42 mN m and linear actuation outputs of ±4.45 mm (±9.1%) and ±0.55 N. Finally, combined multi-DOF actuation is demonstrated as part of development towards scalable holonomic electro-active elastomer actuators. (paper)

Towards holonomic electro-elastomer actuators with six degrees of freedom

Science.gov (United States)

Conn, A. T.; Rossiter, J.

2012-03-01

Functionally efficient six degree of freedom (DOF) actuators have not yet been developed in a scale-invariant and inherently compliant unified form. This has primarily been due to the use of conventional serial or parallel kinematical configurations and electromagnetic motors, pneumatics and hydraulics. Contrary to traditional technologies, utilizing electro-active elastomers enables multi-DOF actuation and holonomic operation with minimal structural complexity. Conical dielectric elastomer actuators (DEAs) are compact multi-DOF actuator-sensors that are scalable and can be entirely polymeric, making them suitable for a variety of applications including minimally invasive medical devices. In this paper, cone DEAs are developed towards integrated 6-DOF actuation with muscle-like performance from a single structure. This is achieved by demonstrating the feasibility of holonomic 6-DOF actuation and through experimental characterization of a 5-DOF prototype. The 5-DOF prototype (50 mm length, 60 mm diameter) produced rotational actuation outputs of ±21.7° and ±9.42 mN m and linear actuation outputs of ±4.45 mm (±9.1%) and ±0.55 N. Finally, combined multi-DOF actuation is demonstrated as part of development towards scalable holonomic electro-active elastomer actuators.

Development of procedures for calculating stiffness and damping of elastomers in engineering applications, part 6

Science.gov (United States)

Rieger, A.; Burgess, G.; Zorzi, E.

1980-01-01

An elastomer damper was designed, tested, and compared with the performance of a hydraulic damper for a power transmission shaft. The six button Viton-70 damper was designed so that the elastomer damper or the hydraulic damper could be activated without upsetting the imbalance condition of the assembly. This permitted a direct comparison of damper effectiveness. The elastomer damper consistently performed better than the hydraulic mount and permitted stable operation of the power transmission shaft to speeds higher than obtained with the squeeze film damper. Tests were performed on shear specimens of Viton-79, Buna-N, EPDM, and Neoprene to determine performance limitations imposed by strain, temperature, and frequency. Frequencies of between 110 Hz and 1100 Hz were surveyed with imposed strains between 0.0005 and 0.08 at temperatures of 32 C, 66 C, and 80 C. A set of design curves was generated in a unified format for each of the elastomer materials.

Evaluation of Depression Associated With Post-Traumatic Stress Disorder After Maxillofacial Injuries-A Prospective Study.

Science.gov (United States)

Ranganathan, Vatsala; Panneerselvam, Elavenil; Chellappazham, Saravanan; Balasubramaniam, Sasikala; Raja V B, Krishnakumar

2018-06-01

Maxillofacial injuries can result in psychological derangement, leading to post-traumatic stress disorder (PTSD), which is characterized by continual re-experiencing of any traumatic event in addition to numerous systemic complications. The objective of this study was to assess the incidence and severity of "PTSD-related depression" in patients with maxillofacial injuries and to identify the risk factors involved. This prospective study involved 88 patients with maxillofacial trauma who had only cosmetic deficits (group A), only functional deficits (group B), or cosmetic and functional deficits (group C). The psychological status of all patients was assessed before and after surgery using Zung's Self-Rating Depression Scale. Remission time also was analyzed. Data were analyzed with SPSS 22.0 using parametric methods. Comparison of mean values among groups was performed using 1-way analysis of variance followed by Tukey honest significance difference post hoc tests for multiple pairwise comparisons. To compare proportions, the χ 2 test was applied. The number of patients in groups A, B, and C was 11, 34 and 43, respectively. In the immediate post-trauma stage, all patients in group A showed severe depression; the percentages of patients with severe depression in groups B and C were 8.8 and 81.4%, respectively, which was statistically relevant. Depression scores of patients of all groups decreased gradually in the postsurgical phase. Patients with cosmetic defects consistently recorded higher depression scores at all intervals. The time taken for recovery from depression (remission time) was shorter for patients with only functional deficits (group B). Patients with maxillofacial injuries are prone to PTSD-related depression from functional and cosmetic deficits. The objectives of trauma management must be aimed at restoring pre-trauma form and function of the maxillofacial skeleton and the patient's psychological status. Copyright © 2018 American Association of

Risk factors for maxillofacial injuries in a Brazilian emergency hospital sample

Directory of Open Access Journals (Sweden)

José Luiz Rodrigues Leles

2010-02-01

Full Text Available BACKGROUND: Maxillofacial injuries occur in a significant number of trauma patients. Epidemiological assessments are essential to reaffirm patterns, identify new trends and develop clinical and research priorities for effective treatment and prevention of these injuries. OBJECTIVE: The aim of this study was to identify the epidemiological profile and risk factors associated with maxillofacial trauma treated at a referral emergency hospital for the Public Health System in the State Capital of Goiás, Brazil. MATERIAL AND METHODS: A cross-sectional study was designed including 530 patients with maxillofacial trauma, 76% male, with a mean age of 25.5±15.0 years. Data were collected between May 2003 and August 2004 over weekly shift-working periods. RESULTS: The main causes of trauma were traffic accidents (45.7% and physical assaults (24.3%, and differences in etiological factors were identified according to gender (p<0.001. The distribution of patients according to age and etiology showed significant differences for traffic accidents (p<0.01, physical assaults (p<0.001, falls (p<0.001 and sport injuries (p<0.01. In the multinomial logistic regression analysis (R² = 0.233; p<0.05, age was associated with injury in traffic accidents and falls (p<0.01, sports-related accidents were associated with males (p<0.05, and alcohol consumption with assaults and traffic accidents (p<0.001. Facial soft tissue lesions were found in 98% of patients and facial fractures in 51%. CONCLUSIONS: The significant association of maxillofacial trauma with young males and alcohol consumption reinforces the need for educational strategies and the development of policies for the prevention and reduction of associated damage in this specific risk group.

[Epidemiology of maxillofacial fractures due to traffic accidents in Medellin (Colombia)].

Science.gov (United States)

Agudelo-Suárez, Andrés A; Duque-Serna, Francisco Levi; Restrepo-Molina, Lucas; Martínez-Herrera, Eliana

2015-09-01

To characterize maxillofacial fractures due to traffic accidents in patients attending the Hospital Universitario San Vicente Fundación (Medellin-Colombia) from 1998 to 2010. A descriptive study (n =1609) was carried out with information from the medical records of patients meeting the inclusion criteria established by the general objective of the study. The variables consisted of sex, age, year, type and number of fractures, and type of vehicle. A descriptive analysis of the variables was performed and the frequency of fractures due to traffic accidents was calculated according to year and sex. Crude and adjusted odds ratios (aOR) were estimated to establish associations among age, type of vehicle, and the presence of two or more fractures with stratification by sex. The frequency of maxillofacial fractures due to traffic accidents increased in 2007 (men: n=198, women: n=35) and decreased from 2008 to 2010 in both sexes. Fractures were more frequent in persons aged <35 years (80%) and in men (82%). The highest frequency of fractures was observed in motorists. Male users of motorcycles (aOR=1.41; confidence interval 95% [95%CI]: 1.02- 1.94) and bicycles (aOR=1.61; 95%CI: 1.01- 2.56) were more likely to report two or more fractures compared with pedestrians, after adjustment for other variables. Most maxillofacial fractures occurred in men and in motorists. Future studies should analyze other determinants affecting the epidemiology of maxillofacial fractures. Strategies should be designed to improve the use of protective elements and drivers' knowledge and practices. Copyright © 2014 SESPAS. Published by Elsevier Espana. All rights reserved.

Hydrogen release from irradiated elastomers measured by Nuclear Reaction Analysis

Energy Technology Data Exchange (ETDEWEB)

Jagielski, J., E-mail: jacek.jagielski@itme.edu.pl [Institute for Electronic Materials Technology, Wolczynska 133, 01-926 Warszawa (Poland); National Centre for Nuclear Research, A. Soltana 7, 05-400 Swierk/Otwock (Poland); Ostaszewska, U. [Institute for Engineering of Polymer Materials & Dyes, Division of Elastomers & Rubber Technology, Harcerska 30, 05-820 Piastow (Poland); Bielinski, D.M. [Technical University of Lodz, Institute of Polymer & Dye Technology, Stefanowskiego 12/16, 90-924 Lodz (Poland); Grambole, D. [Institute of Ion Beam Physics and Materials Research, Helmholtz Zentrum Dresden Rossendorf, PO Box 51 01 19, D-01314 Dresden (Germany); Romaniec, M.; Jozwik, I.; Kozinski, R. [Institute for Electronic Materials Technology, Wolczynska 133, 01-926 Warszawa (Poland); Kosinska, A. [National Centre for Nuclear Research, A. Soltana 7, 05-400 Swierk/Otwock (Poland)

2016-03-15

Ion irradiation appears as an interesting method of modification of elastomers, especially friction and wear properties. Main structural effect caused by heavy ions is a massive loss of hydrogen from the surface layer leading to its smoothening and shrinking. The paper presents the results of hydrogen release from various elastomers upon irradiation with H{sup +}, He{sup +} and Ar{sup +} studied by using Nuclear Reaction Analysis (NRA) method. The analysis of the experimental data indicates that the hydrogen release is controlled by inelastic collisions between ions and target electrons. The last part of the study was focused on preliminary analysis of mechanical properties of irradiated rubbers.

The most-cited articles in dental, oral, and maxillofacial traumatology during 64 years.

Science.gov (United States)

Jafarzadeh, Hamid; Sarraf Shirazi, Alireza; Andersson, Lars

2015-10-01

Citation analysis helps to identify the research trends within a research field and helps to identify the most frequently occurring parameters. The aim of this study was to identify the 100 most-cited articles in the field of dental, oral, and maxillofacial traumatology over the past 64 years. A comprehensive list of the most-cited articles in dental, oral, and maxillofacial trauma was compiled using 'All Databases' section of the ISI Web of Knowledge. Related articles were considered to be those articles in which part or all of the experiment or study was related to dental and/or oral and maxillofacial trauma. In case reports, if a part of a treatment plan was related to the topic, that article was considered to be relevant. The characteristics analyzed included number of citations, authors, journals, institution, country of origin, publication year, article type, study material, and topic. The number of citations for each article ranged from 69 to 229. The journal Dental Traumatology was the most represented, followed by the journal Oral and Maxillofacial Surgery. Of the 100 articles, 83% were original articles, 15% were review articles, and 2% were case report/case series. Therapy and prognosis-related topics were the most common topics. Most articles came from institutions in the United States, followed by the Scandinavian countries. University Hospital of Copenhagen was the source of the highest number (34) of the most-cited articles; the same author wrote or co-wrote 22 of the 100 most-cited articles. The list of most-cited articles in the field of dental, oral, and maxillofacial traumatology gives a good scientometric picture of trauma research in the world. A large number of the most-cited articles are mainly from the field of dental traumatology and originate from a few research teams. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Lightweight mechanical amplifiers for rolled dielectric elastomer actuators and their integration with bio-inspired wing flappers

International Nuclear Information System (INIS)

Lau, Gih-Keong; Lim, Hoong-Ta; Teo, Jing-Ying; Chin, Yao-Wei

2014-01-01

Dielectric elastomer actuators (DEAs) are attractive for use in bio-inspired flapping-wing robots because they have high work density (specific energy) and can produce a large actuation strain. Although the active membrane of a dielectric elastomer is lightweight, the support structure that pre-tensions the elastomeric membrane is massive and it lowers the overall work density. If the DEA is to be used successfully to drive flapping-wing robots, its support structure must be as lightweight as possible. In this work, we designed, analysed, and developed a lightweight shell using a cross-ply laminate of carbon fibre reinforced polymer (CFRP) to pre-strain a rolled DEA. The CFRP shell was shown to weigh 24.3% of the total mass for the whole DEA assembly, while providing up to 35.0% axial pre-strain to a rolled DEA (BJB-5005 silicone rubber). This DEA assembly using the CFRP shell achieved 30.9% of the theoretical work density for a BJB-TC5005 membrane at 33.5 MV m −1 . In comparison, spring rolls with a massive spring core were reported with overall work density merely 10–20% of the maximum value. Furthermore, this CFRP shell can amplify an axial DEA stroke into a larger transverse shell deformation. With these deformation characteristics, this CFRP shell and a rolled DEA were successfully integrated with an insect-inspired thoracic mechanism and they were shown to be feasible to drive it for a flapping wing. (paper)

Use of elastomers in regenerative braking systems

Science.gov (United States)

The storage of potential energy as strain energy in elastomers was investigated. The evolution of the preferred stressing scheme is described, and test results on full-size elastomeric energy storage units sized for an automotive regenerative braking system application are presented. The need for elastomeric material improvements is also discussed.

Tribological behavior of plasma-polymerized aminopropyltriethoxysilane films deposited on thermoplastic elastomers substrates

Energy Technology Data Exchange (ETDEWEB)

Alba-Elías, Fernando, E-mail: fernando.alba@unirioja.es [Department of Mechanical Engineering, University of La Rioja, c/Luis de Ulloa 20, 26004 Logroño, La Rioja (Spain); Sainz-García, Elisa; González-Marcos, Ana [Department of Mechanical Engineering, University of La Rioja, c/Luis de Ulloa 20, 26004 Logroño, La Rioja (Spain); Ordieres-Meré, Joaquín [ETSII, Polytechnic University of Madrid, c/José Gutiérrez Abascal 2, 28006 Madrid (Spain)

2013-07-01

Thermoplastic elastomers (TPE) are multifunctional polymeric materials that are characterized by moderate cost, excellent mechanical properties (high elasticity, good flexibility, hardness, etc.), high tensile strength, oxidation and wettability. With an objective of reducing the superficial friction coefficient of TPE, this work analyzes the characteristics of coating films that are based on aminopropyltriethoxysilane (APTES) over a TPE substrate. Since this material is heat-sensitive, it is necessary to use a technology that permits the deposition of coatings at low temperatures without affecting the substrate integrity. Thus, an atmospheric-pressure plasma jet system (APPJ) with a dielectric barrier discharge (DBD) was used in this study. The coated samples were analyzed by Scanning Electron Microscopy, Atomic Force Microscopy, Fourier-Transform Infrared with Attenuated Total Reflectance Spectroscopy, X-ray Photoelectron Spectroscopy and tribological tests (friction coefficient and wear rate). The studies showed that the coated samples that contain a higher amount of forms of silicon (SiOSi) and nitrogen (amines, amides and imines) have lower friction coefficients. The sample coated at a specific plasma power of 550 W and an APTES flow rate of 1.5 slm had the highest values of SiOSi and nitrogen-containing groups peak intensity and atomic percentages of Si2p and SiO{sub 4}, and the lowest percentages of C1s and average friction coefficient. The results of this research permit one to conclude that APPJ with a DBD is a promising technique to use in coating SiO{sub x} and nitrogen-containing groups layers on polymeric materials. - Highlights: • SiO{sub x} thin films on thermoplastic elastomers by atmospheric pressure plasma jet. • Study of influence of plasma power and precursor flow rate on film's properties. • Friction coefficient is inversely related to the amount of SiOSi and N groups. • Nitrogen groups from the ionization gas (N{sub 2}) seem to

Investigation on the performance of a viscoelastic dielectric elastomer membrane generator.

Science.gov (United States)

Zhou, Jianyou; Jiang, Liying; Khayat, Roger E

2015-04-21

Dielectric elastomer generators (DEGs), as a recent transduction technology, harvest electrical energy by scavenging mechanical energy from diverse sources. Their performance is affected by various material properties and failure modes of the dielectric elastomers. This work presents a theoretical analysis on the performance of a dielectric elastomer membrane generator under equi-biaxial loading conditions. By comparing our simulation results with the experimental observations existing in the literature, this work considers the fatigue life of DE-based devices under cyclic loading for the first time. From the simulation results, it is concluded that the efficiency of the DEG can be improved by raising the deforming rate and the prescribed maximum stretch ratio, and applying an appropriate bias voltage. However, the fatigue life expectancy compromises the efficiency improvement of the DEG. With the consideration of the fatigue life, applying an appropriate bias voltage appears to be a more desirable way to improve the DEG performance. The general framework developed in this work is expected to provide an increased understanding on the energy harvesting mechanisms of the DEGs and benefit their optimal design.

Multiple Synchronous Central Giant Cell Granulomas of the Maxillofacial Region: A Case Report

International Nuclear Information System (INIS)

Kang, Min Seok; Kim, Hak Jin

2010-01-01

Multifocal central giant cell granulomas (CGCG) in the maxillofacial region are suggestive of systemic disease such as hyperparathyroidism or an inherited syndrome such as Noonan-like multiple giant cell lesion syndrome. Only 5 cases of multifocal CGCGs in the maxillofacial region without any concomitant systemic disease have currently been reported. We report here on an unusual case of 17-year-old man who presented with multifocal CGCGs of the bilateral posterior mandible and right maxilla and he was without any concomitant systemic disease

Multiple Synchronous Central Giant Cell Granulomas of the Maxillofacial Region: A Case Report

Energy Technology Data Exchange (ETDEWEB)

Kang, Min Seok; Kim, Hak Jin [Pusan National University Hospital, Busan (Korea, Republic of)

2010-01-15

Multifocal central giant cell granulomas (CGCG) in the maxillofacial region are suggestive of systemic disease such as hyperparathyroidism or an inherited syndrome such as Noonan-like multiple giant cell lesion syndrome. Only 5 cases of multifocal CGCGs in the maxillofacial region without any concomitant systemic disease have currently been reported. We report here on an unusual case of 17-year-old man who presented with multifocal CGCGs of the bilateral posterior mandible and right maxilla and he was without any concomitant systemic disease

Material Evaluation of an Elastomer, Epoxy and Lightweight Concrete Rail Attachment System for Direct Fixation Light Rail Applications

Science.gov (United States)

Swarner, Benjamin R.

Sound Transit plans to extend its current light rail system, which runs along the I-5 corridor in Seattle, Washington, across the I-90 Homer Hadley floating bridge as part of a project to connect the major city centers in the region. But, no light rail has ever crossed a floating bridge due to several unique engineering challenges. One of these challenges is attaching the rails to the existing bridge deck without drilling into the bridge pontoons. This research program was developed to test and analyze a direct fixation method that uses lightweight concrete plinths and an elastomer-epoxy system to attach the rails to the bridge deck. The elastomer used was a two-part, pourable elastomer with cork particles intermixed to alter the mechanical properties of the material. A lightweight concrete mixture was analyzed for use in the plinths, and system tests investigated the system response under tensile, compressive and shear loading. The shear response of the system was examined further under varying loading conditions including different surface preparations, elastomer thicknesses, strain-rates and after freeze-thaw conditioning. Experimental data was examined for trends based on these parameters to best characterize the system, and the elastomer was evaluated in the context of modern elastomer research.

The role of 3D Helical CT in the reconstructive treatment of maxillofacial cancers

International Nuclear Information System (INIS)

De Rosa, V.; Ziviello, M.; Ionna, F.; Mozzillo, N.; Parascandolo, S.

2000-01-01

Purpose of this work is to investigate the role of Helical CT and the usefulness of three-dimensional (3D) imaging for pre-operative planning and follow-up of reconstructive maxillofacial surgery with alloplastic material in neoplastic disease involving this region. From 1996 to 1999 eleven patients were examined with Helical CT and 3D images for planning of maxillofacial plastic and reconstructive surgery for advanced cancer of this anatomically complex region. A 3D-modulated titanium mesh (100%) or micro nets was used to rebuild the anterior surface of maxillary bone and the orbital floor. The mesh was cut to the appropriate size and shape and curved where necessary. Within the residual sinusal cavity a siliconed filling was used surmounting an acrylic prosthesis with dental arch to rebuild the palate. A rehydrated bovine pericardium was affixed and moduled on the borders in two cases only. Three-dimensionally reconstructed CT images were obtained preoperatively and at least 6 months postoperatively in all patients. The images were generated on a computer workstation using the shaded surface display (SSD) software with threshold values ranging 425 to 630 HU, and a more closed window for the imaging of titanium mesh/bone interface in the post surgical follow-up. It was obtained an excellent complete spatial depiction of maxillo facial region both before and after surgery, with no artefacts so important as to affect the 3D reconstruction process and the image quality. Together with the head-neck surgical team it could be worked for preoperative planning through CT scans by different 3D points of view. The 3D reconstructed follow-up scans showed good filling of the defect in the area where the titanium mesh had been used. Then efficacious bone modelling and good biocompatibility of the alloplastic material were seen in all patients, with no inflammatory reactions. Titanium is a well-known material, which is widely used for cranioplasty. It is a radiolucent, non

Secondary reconstruction of maxillofacial trauma.

Science.gov (United States)

Castro-Núñez, Jaime; Van Sickels, Joseph E

2017-08-01

Craniomaxillofacial trauma is one of the most complex clinical conditions in contemporary maxillofacial surgery. Vital structures and possible functional and esthetic sequelae are important considerations following this type of trauma and intervention. Despite the best efforts of the primary surgery, there are a group of patients that will have poor outcomes requiring secondary reconstruction to restore form and function. The purpose of this study is to review current concepts on secondary reconstruction to the maxillofacial complex. The evaluation of a posttraumatic patient for a secondary reconstruction must include an assessment of the different subunits of the upper face, middle face, and lower face. Virtual surgical planning and surgical guides represent the most important innovations in secondary reconstruction over the past few years. Intraoperative navigational surgery/computed-assisted navigation is used in complex cases. Facial asymmetry can be corrected or significantly improved by segmentation of the computerized tomography dataset and mirroring of the unaffected side by means of virtual surgical planning. Navigational surgery/computed-assisted navigation allows for a more precise surgical correction when secondary reconstruction involves the replacement of extensive anatomical areas. The use of technology can result in custom-made replacements and prebent plates, which are more stable and resistant to fracture because of metal fatigue. Careful perioperative evaluation is the key to positive outcomes of secondary reconstruction after trauma. The advent of technological tools has played a capital role in helping the surgical team perform a given treatment plan in a more precise and predictable manner.

Oral and maxillofacial surgical conditions in Nigeria. | Adebayo ...

African Journals Online (AJOL)

The Niger Delta region comprises 9 of the 36 states in the Federal Republic of Nigeria. ... 2000 and 2004, our center offered specialized maxillofacial surgical services to ... Ratio of male to female patients was 1.7:1 while patients were aged between 9 ... Health promotion activities are needed to improve awareness for early

Risk of surgical glove perforation in oral and maxillofacial surgery.

Science.gov (United States)

Kuroyanagi, N; Nagao, T; Sakuma, H; Miyachi, H; Ochiai, S; Kimura, Y; Fukano, H; Shimozato, K

2012-08-01

Oral and maxillofacial surgery, which involves several sharp instruments and fixation materials, is consistently at a high risk for cross-contamination due to perforated gloves, but it is unclear how often such perforations occur. This study aimed to address this issue. The frequency of the perforation of surgical gloves (n=1436) in 150 oral and maxillofacial surgeries including orthognathic surgery (n=45) was assessed by the hydroinsufflation technique. Orthognathic surgery had the highest perforation rate in at least 1 glove in 1 operation (91.1%), followed by cleft lip and palate surgery (55.0%), excision of oral soft tumour (54.5%) and dental implantation (50.0%). The perforation rate in scrub nurses was 63.4%, followed by 44.4% in surgeons and first assistants, and 16.3% in second assistants. The odds ratio for the perforation rate in orthognathic surgery versus other surgeries was 16.0 (95% confidence interval: 5.3-48.0). The protection rate offered by double gloving in orthognathic surgery was 95.2%. These results suggest that, regardless of the surgical duration and blood loss in all fields of surgery, orthognathic surgery must be categorized in the highest risk group for glove perforation, following gynaecological and open lung surgery, due to the involvement of sharp objects. Copyright © 2012 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Mimicking biological stress-strain behaviour with synthetic elastomers

Science.gov (United States)

Vatankhah-Varnosfaderani, Mohammad; Daniel, William F. M.; Everhart, Matthew H.; Pandya, Ashish A.; Liang, Heyi; Matyjaszewski, Krzysztof; Dobrynin, Andrey V.; Sheiko, Sergei S.

2017-09-01

Despite the versatility of synthetic chemistry, certain combinations of mechanical softness, strength, and toughness can be difficult to achieve in a single material. These combinations are, however, commonplace in biological tissues, and are therefore needed for applications such as medical implants, tissue engineering, soft robotics, and wearable electronics. Present materials synthesis strategies are predominantly Edisonian, involving the empirical mixing of assorted monomers, crosslinking schemes, and occluded swelling agents, but this approach yields limited property control. Here we present a general strategy for mimicking the mechanical behaviour of biological materials by precisely encoding their stress-strain curves in solvent-free brush- and comb-like polymer networks (elastomers). The code consists of three independent architectural parameters—network strand length, side-chain length and grafting density. Using prototypical poly(dimethylsiloxane) elastomers, we illustrate how this parametric triplet enables the replication of the strain-stiffening characteristics of jellyfish, lung, and arterial tissues.

Magnetic force induced tristability for dielectric elastomer actuators

Science.gov (United States)

Li, Xin-Qiang; Li, Wen-Bo; Zhang, Wen-Ming; Zou, Hong-Xiang; Peng, Zhi-Ke; Meng, Guang

2017-10-01

This paper presents a novel dielectric elastomer actuator (DEA) with three stable states. By introducing magnetic forces and coupling them with two cone dielectric elastomer (DE) films, an inherent tristability for the DEA is obtained with a compact design. It is easy to switch between the three stable states by controlling the voltages applied to the DE films. A theoretical model of the system’s potential energy that contains the free energy of the DEs and the potential energy of the applied magnetic field was developed for the tristable mechanism. The experimental results demonstrate that controllable transitions between the three stable states can be achieved with this design by applying over-critical voltages to the various DE films. The maximum dynamic range of the DEA can exceed 53.8% of the total length of the device and the DE’s creep speed was accelerated under the action of the magnetic field.

Synthesis of novel lidocaine-releasing poly(diol-co-citrate) elastomers by using deep eutectic solvents.

Science.gov (United States)

Serrano, M Concepción; Gutiérrez, María C; Jiménez, Ricardo; Ferrer, M Luisa; del Monte, Francisco

2012-01-14

Poly(octanediol-co-citrate) elastomers containing high loading of lidocaine were synthesized at temperatures below 100 °C by means of using deep eutectic mixtures of 1,8-octanediol and lidocaine. The preservation of lidocaine integrity resulted in high-capacity drug-eluting elastomers. This journal is © The Royal Society of Chemistry 2012

A fiber-reinforced composite prosthesis restoring a lateral midfacial defect: a clinical report.

Science.gov (United States)

Kurunmäki, Hemmo; Kantola, Rosita; Hatamleh, Muhanad M; Watts, David C; Vallittu, Pekka K

2008-11-01

This clinical report describes the use of a glass fiber-reinforced composite (FRC) substructure to reinforce the silicone elastomer of a large facial prosthesis. The FRC substructure was shaped into a framework and embedded into the silicone elastomer to form a reinforced facial prosthesis. The prosthesis is designed to overcome the disadvantages associated with traditionally fabricated prostheses; namely, delamination of the silicone of the acrylic base, poor marginal adaptation over time, and poor simulation of facial expressions.

A ten year analysis of the traumatic maxillofacial and brain injury patient in Amsterdam: complications and treatment

NARCIS (Netherlands)

Salentijn, E.G.; Collin, J.D.; Boffano, P.; Forouzanfar, T.

2014-01-01

Maxillofacial trauma is often associated with injuries to the cranium, especially in high-energy trauma. The management of such cases can be challenging and requires close cooperation between oral and maxillofacial surgery and neurosurgical teams. There are few reports in the current literature

Nanomechanical probing of thin-film dielectric elastomer transducers

Science.gov (United States)

Osmani, Bekim; Seifi, Saman; Park, Harold S.; Leung, Vanessa; Töpper, Tino; Müller, Bert

2017-08-01

Dielectric elastomer transducers (DETs) have attracted interest as generators, actuators, sensors, and even as self-sensing actuators for applications in medicine, soft robotics, and microfluidics. Their performance crucially depends on the elastic properties of the electrode-elastomer sandwich structure. The compressive displacement of a single-layer DET can be easily measured using atomic force microscopy (AFM) in the contact mode. While polymers used as dielectric elastomers are known to exhibit significant mechanical stiffening for large strains, their mechanical properties when subjected to voltages are not well understood. To examine this effect, we measured the depths of 400 nanoindentations as a function of the applied electric field using a spherical AFM probe with a radius of (522 ± 4) nm. Employing a field as low as 20 V/μm, the indentation depths increased by 42% at a load of 100 nN with respect to the field-free condition, implying an electromechanically driven elastic softening of the DET. This at-a-glance surprising experimental result agrees with related nonlinear, dynamic finite element model simulations. Furthermore, the pull-off forces rose from (23.0 ± 0.4) to (49.0 ± 0.7) nN implying a nanoindentation imprint after unloading. This embossing effect is explained by the remaining charges at the indentation site. The root-mean-square roughness of the Au electrode raised by 11% upon increasing the field from zero to 12 V/μm, demonstrating that the electrode's morphology change is an undervalued factor in the fabrication of DET structures.

Oro-Dental and Maxillofacial Trauma in Epilepsy at a Tertiary ...

African Journals Online (AJOL)

Oro-Dental and Maxillofacial Trauma in Epilepsy at a Tertiary Hospital in Lagos. ... Information sought included patient's sociodemographics, type of seizure, ... bones were not so common, all such cases received surgical treatment in hospital.

Trends in maxillofacial cone-beam computed tomography usage

International Nuclear Information System (INIS)

Arnheiter, C.; Scarfe, W.C.; Farman, A.G.

2006-01-01

Cone-beam computed tomography (CBCT) is making inroads into dental practice worldwide, both in terms of adding the third dimension to diagnosis, and also in terms of enabling image-guided treatment strategies. This article reports trends in the early referral pattern of patients to a CBCT facility in the United States. With institutional review board approval, a retrospective study was made of sequential CBCT radiographic reports made by a specialist oral and maxillofacial radiology service from May 2004 through January 2006 (n=329). Demographic and referral data were extracted from the reports. Descriptive statistics identified referral patterns, trends, and indications for CBCT. Comparisons were made with the Rogers' Product Innovation Adoption curve. The mean age of referred patients was 45±21 years, and there was a predominance of women (62%). Oral and maxillofacial surgeons (51%) and periodontology specialists (17%) made most patient referrals. The listed reasons for CBCT referrals were dental implant planning (40%), suspected surgical pathology (24%), and temporomandibular joint analysis (16%). Other uses included planning extraction of impacted teeth and orthodontic assessment. Over the period of the study, the numbers of pathology diagnosis cases remained relatively constant, while adoption of CBCT for dental implant planning followed closely the first three stages of the Rogers' Product Innovation Adoption curve. Alongside this increased CBCT adoption for dental implant planning, there was an associated increased demand for use of Digital Imaging and Communications in Medicine (DICOM) image sets for laser modeling and provision of surgical guides. Diagnosis will probably remain a constant source of referral for CBCT examination by oral and maxillofacial radiologists. Nevertheless, more specialized applications such as laser-guided model fabrication and image-guided surgery are expanding indications for CBCT referrals by dentists and also expanding the

Oral, Maxillofacial and Dental Diseases in Captive Cheetahs (Acinonyx jubatus).

Science.gov (United States)

Steenkamp, G; Boy, S C; van Staden, P J; Bester, M N

2018-01-01

Descriptions of several oral, maxillofacial and dental conditions/diseases exist for a variety of captive large felids, but little is reported on the pathology of free roaming large felids. Apart from focal palatine erosions (FPEs) as initially described by Fitch and Fagan (1982) and some reference to absent incisor teeth, few data exist on diseases affecting the oral, maxillofacial and dental structures of cheetahs (Acinonyx jubatus), regardless of their captivity status. This study reports 18 different conditions affecting the teeth, bone and oral cavity soft tissue of cheetahs, based on initial assessment of 256 animals over 11 years (2002-2012) in South Africa and Namibia. This report excludes oral tumours or FPEs, but includes several acquired and developmental conditions never described before. Copyright © 2017 Elsevier Ltd. All rights reserved.

Maxillofacial trauma patient: coping with the difficult airway

Directory of Open Access Journals (Sweden)

Barak Michal

2009-05-01

Full Text Available Abstract Establishing a secure airway in a trauma patient is one of the primary essentials of treatment. Any flaw in airway management may lead to grave morbidity and mortality. Maxillofacial trauma presents a complex problem with regard to the patient's airway. By definition, the injury compromises the patient's airway and it is, therefore, must be protected. In most cases, the patient undergoes surgery for maxillofacial trauma or for other, more severe, life-threatening injuries, and securing the airway is the first step in the introduction of general anaesthesia. In such patients, we anticipate difficult endotracheal intubation and, often, also difficult mask ventilation. In addition, the patient is usually regarded as having a "full stomach" and has not been cleared of a C-spine injury, which may complicate airway management furthermore. The time available to accomplish the task is short and the patient's condition may deteriorate rapidly. Both decision-making and performance are impaired in such circumstances. In this review, we discuss the complexity of the situation and present a treatment approach.

Dental and Maxillofacial Signs in Aarskog Syndrome: A Review of 3 Siblings and the Literature.

Science.gov (United States)

Depeyre, Arnaud; Schlund, Matthias; Gryseleyn, Rémi; Ferri, Joel

2018-03-29

Dagfinn Aarksog first described faciodigitogenital syndrome in 1970. Its inheritance is X linked and autosomally recessive. Currently, the diagnosis of Aarskog-Scott syndrome (ASS) is based on clinical dysmorphologic findings and can be supported by genetic examination. This report describes 3 brothers already diagnosed with ASS who were referred for examination of oral and maxillofacial malformations associated with ASS. They presented classic features of ASS, such as digital and genital (shawl scrotum) anomalies. More specifically, in terms of orbitopalpebral malformations, they showed marked ptosis with hypertelorism and antimongoloid palpebral fissure that gave them the characteristic facies. Concerning their oral and maxillofacial malformations, they had dental and skeletal major discrepancies and some dental agenesia. ASS is a rare X-linked syndrome composed of numerous morphologic facial, digital, and genital anomalies. The diagnosis is established genetically with the FGD1 mutation but there is no phenotypic and genotypic correlation with FGD1 mutations. Concerning maxillofacial malformations, maxillary and mandibular hypoplasia with jaw discrepancies can be found, as can teeth anomalies. It seems that these anomalies are widely underestimated. Copyright © 2018 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

3D workflows in orthodontics, maxillofacial surgery and prosthodontics

NARCIS (Netherlands)

van der Meer, Wicher Jurjen

2016-01-01

In this thesis different aspects of digital workflows in Orthodontics, Maxillofacial Surgery and Prosthodontics are discussed and, where possible, placed in a broader perspective thereby attempting to go both broader and deeper into the implications of the introduction of 3D digital technology in

Pengerasan Pada Bahan Cetak Elastomer Polyether

OpenAIRE

Azree Zayani M.S.

2011-01-01

Bahan cetak polyether merupakan bahan elastomer yang digunakan di kedokteran gigi. Terdapat empat kelas menurut konsistensi dan viskositas yaitu (1) light body (2)medium atau regular body (3) heavy body: dan (4) Putty. Komposisi bahan cetak polyether terdiri dari pasta base dan pasta katalis. Pasta base mengandung polimer polyether, kolloidal silika sebagai bahan pengisi, dan plastisizer yaitu glikoeter atau phthalate. Pasta katalis mengandung alkil aromatik sulfonat ditambah dengan baha...

Four years prospective study of the maxillofacial trauma at a tertiary center in Western Nepal

Directory of Open Access Journals (Sweden)

Rajib Khadka

2014-01-01

Full Text Available Purpose: This study was conducted to find the epidemiological characteristics of maxillofacial trauma in the Western region of Nepal. Materials and Methods: All the trauma patients attending the Department of Oral and Maxillofacial surgery in 4 years period at a tertiary center in Western Nepal were included in the study. The incidence, prevalence, age and sex distribution, etiologies and types as well as seasonal and daily variation of maxillofacial trauma were studied. Results: Maxillofacial trauma with male (71.55% predominance was seen. Road traffic accidents (RTA, 46.5% were the most common cause, and 41.65% of fracture cases due to RTA were under the influence of alcohol. Accidents were more common on the rural roads (38.9%, and majorities (43.3% were due to motorcycle accidents. They were more common on Friday (36.7% and in winter seasons (51.2%. The mandible fractures (65.85% were more common than midface fractures (53.58% and 19.44% of the fractures were combined fractures. Parasymphysis in mandible (32.16% and zygoma (39.09% in midface were the most common type of fracture. Conclusion: The increased incidence of maxillofacial trauma following RTA under the influence of alcohol noted in this study reveals the need for formulating preventive measures in the Western region of Nepal. Need to aware people to avoid drink and drive proper traffic management, prevention of carrying excessive passengers, especially on the rooftop of vehicles on the highway and disposal of out of date vehicles and timely maintenance of faulty roads is a must.

Novel polycarbonate-based polyurethane elastomers: composition–property relationship

Czech Academy of Sciences Publication Activity Database

Špírková, Milena; Pavličevic, J.; Strachota, Adam; Poreba, Rafal; Bera, O.; Kaprálková, Ludmila; Baldrian, Josef; Šlouf, Miroslav; Lazić, N.; Budinski-Simendic, J.

2011-01-01

Roč. 47, č. 5 (2011), s. 959-972 ISSN 0014-3057 R&D Projects: GA ČR GAP108/10/0195 Institutional research plan: CEZ:AV0Z40500505 Keywords : polyurethane elastomer * polycarbonate diol * montmorillonite Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.739, year: 2011

On the decrease of ultimate elongation of gum elastomer by irradiation

International Nuclear Information System (INIS)

Ito, Masayuki

1986-01-01

The reason why the ultimate elongation of gum elastomer decreases by irradiation was studied. The sample used is tetrafluoroethylenepropylene copolymer vulcanized which is a heat resistant elastomer. The sample was irradiated by a electron beam at room temperature. Cross-linking predominate in the operation. (Case 1) Scission predominant condition (Case 2) was given by irradiation of Co-60 γ ray at 100 deg C. Alternative irradiation of γ ray and electron beam under above condition can keep the original cross-linking density by the appropriate choice of each of the doses. (Case 3) The three cases mentioned above involve all of the cases of radiation induced aging of elastomers. Therefor, the following explanation for three cases shows the reason why the ultimate elongation of gum elastomer decreases by irradiation. Case 1. Cross-linking predominant condition. Ultimate elongation is proportional to -0.5 power of the dose. This fact can be explicable by the model of Buche, i.e. the breaking of a short chain causes another to break and that so on throughout the whole sample. Case 2. Chain scission predominant condition. Ultimate elongation increases by irradiation for a certain dose. This fact can understand by the model of Buche. But from a certain dose ultimate elongation does not increase. In the period the structure of the sample turned to be the same structure as the low molecular weight amorphose polymer vulcanized. Case 3. Rate of cross-linking and scission is the same. The average chain length does not chainge in the condition. But the distribution of chain length became wider and wider by irradiation. The increase of short chain result the decrease in ultimate elongation. (author)

Motorcycle accident is the main cause of maxillofacial injuries in the Penang Mainland, Malaysia.

Science.gov (United States)

Hashim, Hasnah; Iqbal, Syed

2011-02-01

Maxillofacial injuries are among the commonest forms of body injuries. There are three divisions, namely, facial bone fractures, soft tissue injuries, and dentoalveolar injuries. Etiologies include motor vehicle accidents, assaults, falls, and sporting injuries. The aim of this study was to determine the profiles including the causes of maxillofacial injuries seen in an urban government hospital in the mainland of Penang State, Malaysia. This was a cross-sectional study that recruited cases reported within a period of 1 year. The source population was maxillofacial injury patients presenting to the Oral and Maxillofacial Surgery Department of an urban hospital in the Penang Mainland, North Malaysia between May 2007 and May 2008. Cases of patients involved in accidents that occurred outside the reference vicinity were excluded. A case report form was developed and completed by the attending clinicians. Data were analyzed using spss version 12.0. A total of 194 cases were studied, with the mean patient age being 27.8 (SD 15.20) years. The majority of patients were Malay men between 20 and 29 years of age. The main cause of injury was motorcycle accident (53.6%). The commonest injury (in isolation/combination with other injuries) involved the soft tissues (87.2%), dentoalveolar region (33.4%), and facial bones (23.9%). Laceration was the commonest soft tissue injury, and crown fracture was the most frequent dentoalveolar injury. The facial bone that was most highly involved in the injury was the zygoma. Subjects involved in motorcycle accidents had a significantly higher incidence of sustaining facial bone fractures. Motorcycle accidents were the commonest cause of maxillofacial injuries in the Penang Mainland, Malaysia. Most patients were young men. Hence, it is prudent to reinforce appropriate road safety and awareness interventions particularly focusing young male motorcyclists so as to reduce the risk of accidents. © 2011 John Wiley & Sons A/S.

Surgical Engineering in Cranio-Maxillofacial Surgery: A Literature Review

Directory of Open Access Journals (Sweden)

Raphael Olszewski

2012-01-01

Full Text Available A systematic review of the literature concerning surgical engineering in cranio-maxillofacial surgery was performed. APubMed search yielded 1721 papers published between 1999 and 2011. Based on the inclusion/exclusion criteria, 1428 articles were excluded after review of titles and abstracts. Atotal of 292 articles were finally selected covering the following topics: finite element analysis (n = 18, computer-assisted surgery (n = 111, rapid prototyping models (n = 41, preoperative training simulators (n = 4, surgical guides (n = 23, image-guided navigation (n = 58, augmented reality (n = 2, video tracking (n = 1, distraction osteogenesis (n = 19, robotics (n = 8, and minimal invasive surgery (n = 7. The results show that surgical engineering plays a pivotal role in the development and improvement of cranio-maxillofacial surgery. Some technologies, such as computer-assisted surgery, image-guided navigation, and three-dimensional rapid prototyping models, have reached maturity and allow for multiple clinical applications, while augmented reality, robotics, and endoscopy still need to be improved.

Which Factors Affect Citation Rates in the Oral and Maxillofacial Surgery Literature?

Science.gov (United States)

Cheng, Kristie L; Dodson, Thomas B; Egbert, Mark A; Susarla, Srinivas M

2017-07-01

Citation rate is one of several tools to measure academic productivity. The purposes of this study were to estimate and identify factors associated with citation rates in the oral and maxillofacial surgery (OMS) literature. This was a retrospective longitudinal study of publications in the Journal of Oral and Maxillofacial Surgery (JOMS), International Journal of Oral and Maxillofacial Surgery (IJOMS), and Oral Surgery, Oral Medicine, Oral Pathology, and Oral Radiology (OOOO) from January through December 2012. The predictor variables were author- and article-specific factors. The outcome variable was the citation rate, defined as the total number of citations for each article over a 4-year period. Descriptive, bivariate, and multiple regression statistics were computed. The authors identified 993 articles published during 2012. The mean number of citations at 4 years after publication was 5.6 ± 5.3 (median, 4). In bivariate analyses, several author- and article-specific factors were associated with citation rates. In a multiple regression model adjusting for potential confounders and effect modifiers, first author H-index, number of authors, journal, OMS focus area, and Oxford level of evidence were significantly associated with citation rate (P ≤ .002). The authors identified 5 factors associated with citation rates in the OMS literature. These factors should be considered in context when evaluating citation-based metrics for OMS. Studies that focus on core OMS procedures (eg, dentoalveolar surgery, dental implant surgery), are published in specialty-specific journals (eg, JOMS or IJOMS), and have higher levels of evidence are more likely to be cited. Copyright © 2017 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

A ten-year analysis of the traumatic maxillofacial and brain injury patient in Amsterdam: incidence and aetiology

NARCIS (Netherlands)

Salentijn, E.G.; Peerdeman, S.M.; Boffano, P.; van den Bergh, B.; Forouzanfar, T.

2014-01-01

In the literature it is questioned if the presence of maxillofacial trauma is associated with the presence of brain injury. The aim of this study is to present a 10-year retrospective study of the incidence and aetiology of maxillofacial trauma associated with brain injury that required both oral

A ten-year analysis of the traumatic maxillofacial and brain injury patient in Amsterdam: Incidence and aetiology

NARCIS (Netherlands)

Salentijn, E.G.; Peerdeman, S.M.; Boffano, P.; van den Bergh, B.; Forouzanfar, T.

2014-01-01

In the literature it is questioned if the presence of maxillofacial trauma is associated with the presence of brain injury. The aim of this study is to present a 10-year retrospective study of the incidence and aetiology of maxillofacial trauma associated with brain injury that required both oral

Reliability in maintenance and design of elastomer sealed closures

International Nuclear Information System (INIS)

Lake, W.H.

1978-01-01

The methods of reliability are considered for maintenance and design of elastomer sealed containment closures. Component reliability is used to establish a replacement schedule for system maintenance. Reliability data on elastomer seals is used to evaluate the common practice of annual replacement, and to calculate component reliability values for several typical shipment time periods. System reliability methods are used to examine the relative merits of typical closure designs. These include single component and redundant seal closure, with and without closure verification testing. The paper presents a general method of quantifying the merits of closure designs through the use of reliability analysis, which is a probabilistic technique. The reference list offers a general source of information in the field of reliability, and should offer the opportunity to extend the procedures discussed in this paper to other design safety applications

Materials, Mechanics, and Patterning Techniques for Elastomer-Based Stretchable Conductors

Directory of Open Access Journals (Sweden)

Xiaowei Yu

2016-12-01

Full Text Available Stretchable electronics represent a new generation of electronics that utilize soft, deformable elastomers as the substrate or matrix instead of the traditional rigid printed circuit boards. As the most essential component of stretchable electronics, the conductors should meet the requirements for both high conductivity and the capability to maintain conductive under large deformations such as bending, twisting, stretching, and compressing. This review summarizes recent progresses in various aspects of this fascinating and challenging area, including materials for supporting elastomers and electrical conductors, unique designs and stretching mechanics, and the subtractive and additive patterning techniques. The applications are discussed along with functional devices based on these conductors. Finally, the review is concluded with the current limitations, challenges, and future directions of stretchable conductors.

Orthodontic treatment for oral rehabilitation after multiple maxillofacial bone fractures.

Science.gov (United States)

Nakamura, Yoshiki; Ogino, Tomoko Kuroiwa; Hirashita, Ayao

2008-09-01

We present the orthodontic treatment of a patient with occlusal dysfunction after plastic surgery for multiple maxillofacial bone fractures caused by a traffic accident. The patient had mandibular deviation to the right because of inappropriate repositioning and fixation of the fractured bone and complete avulsion of both mandibular central incisors. The bilateral mandibular incisors, canines, and premolars were also suspected of partial avulsion or alveolar bone fracture. Several tests, including percussion and dental computed tomography, were performed on these teeth to rule out ankylosis and confirm tooth movement. Camouflage orthodontic treatment was carried out with expansion of the maxillary arch, alignment of both arches, and space closure between the mandibular lateral incisors to improve the occlusion. Good occlusion and interdigitation were obtained. Orthodontic treatment is useful for the rehabilitation of occlusal dysfunction caused by multiple maxillofacial bone fractures.

Fabrication of non-dissolving analgesic suppositories using 3D printed moulds.

Science.gov (United States)

Sun, Yuanyuan; Ruan, Xucong; Li, Hairui; Kathuria, Himanshu; Du, Guang; Kang, Lifeng

2016-11-20

Conventional suppositories sometimes fail in exerting their therapeutic activity as the base materials melt inside body cavities. Also they are not suitable to provide long term treatment. Biomedical grade silicone elastomers may be used to fabricate non-dissolvable suppositories to overcome these disadvantages. We kneaded 4 analgesics into the 2 kinds of silicone polymers at 1%, 5% and 10% drug loading, respectively, to test their mechanical properties and drug release profiles. The optimized drug-polymer combinations were used to fabricate suppositories, and three dimensional printing (3DP) was used to create the suppository moulds. Subsequently, the drug release profiles and biocompatibility of the suppositories were studied. It was found that, the mechanical properties of the drug laden silicone elastomers and the rate of drug release from the elastomers can be tuned by varying drug-polymer combinations. The silicone elastomers containing 1% (w/w) and 5% (w/w) diclofenac sodium were the optimal formulations with prolonged drug release and biocompatibility at cellular level. These properties, together with complex geometries offered by 3DP technique, potentially made the non-dissolving suppositories promising therapeutic agents for personalized medicine. Copyright © 2016 Elsevier B.V. All rights reserved.

Radiologic assessment of maxillofacial, mandibular, and skull base trauma

International Nuclear Information System (INIS)

Schuknecht, Bernhard; Graetz, Klaus

2005-01-01

Cranio-maxillofacial injuries affect a significant proportion of trauma patients either in isolation or concurring with other serious injuries. Contrary to maxillofacial injuries that result from a direct impact, central skull base and lateral skull base (petrous bone) fractures usually are caused by a lateral or sagittal directed force to the skull and therefore are indirect fractures. The traditional strong role of conventional images in patients with isolated trauma to the viscerocranium is decreasing. Spiral multislice CT is progressively replacing the panoramic radiograph, Waters view, and axial films for maxillofacial trauma, and is increasingly being performed in addition to conventional films to detail and classify trauma to the mandible as well. Imaging thus contributes to accurately categorizing mandibular fractures based on location, into alveolar, mandibular proper, and condylar fractures - the last are subdivided into intracapsular and extracapsular fractures. In the midface, CT facilitates attribution of trauma to the categories central, lateral, or combined centrolateral fractures. The last frequently encompass orbital trauma as well. CT is the imaging technique of choice to display the multiplicity of fragments, the degree of dislocation and rotation, or skull base involvement. Transsphenoid skull base fractures are classified into transverse and oblique types; lateral base (temporal bone) trauma is subdivided into longitudinal and transverse fractures. Supplementary MR examinations are required when a cranial nerve palsy occurs in order to recognize neural compression. Early and late complications of trauma related to the orbit, anterior cranial fossa, or lateral skull base due to infection, brain concussion, or herniation require CT to visualize the osseous prerequisites of complications, and MR to define the adjacent brain and soft tissue involvement. (orig.)

An Experimental Investigation of Leak Rate Performance of a Subscale Candidate Elastomer Docking Space Seal

Science.gov (United States)

Garafolo, Nicholas G.; Daniels, Christopher C.

2011-01-01

A novel docking seal was developed for the main interface seal of NASA s Low Impact Docking System (LIDS). This interface seal was designed to maintain acceptable leak rates while being exposed to the harsh environmental conditions of outer space. In this experimental evaluation, a candidate docking seal assembly called Engineering Development Unit (EDU58) was characterized and evaluated against the Constellation Project leak rate requirement. The EDU58 candidate seal assembly was manufactured from silicone elastomer S0383-70 vacuum molded in a metal retainer ring. Four seal designs were considered with unique characteristic heights. The leak rate performance was characterized through a mass point leak rate method by monitoring gas properties within an internal control volume. The leakage performance of the seals were described herein at representative docking temperatures of -50, +23, and +50 C for all four seal designs. Leak performance was also characterized at 100, 74, and 48 percent of full closure. For all conditions considered, the candidate seal assemblies met the Constellation Project leak rate requirement.

Dental and maxillofacial abnormalities in long-term survivors of childhood cancer: effects of treatment with chemotherapy and radiation to the head and neck

International Nuclear Information System (INIS)

Jaffe, N.; Toth, B.B.; Hoar, R.E.; Ried, H.L.; Sullivan, M.P.; McNeese, M.D.

1984-01-01

Sixty-eight long-term survivors of childhood cancer were evaluated for dental and maxillofacial abnormalities. Forty-five patients had received maxillofacial radiation for lymphoma, leukemia, rhabdomyosarcoma, and miscellaneous tumors. Forty-three of the 45 patients and the remaining 23 who had not received maxillofacial radiation also received chemotherapy. Dental and maxillofacial abnormalities were detected in 37 of the 45 (82%) radiated patients. Dental abnormalities comprised foreshortening and blunting of roots, incomplete calcification, premature closure of apices, delayed or arrested tooth development, and caries. Maxillofacial abnormalities comprised trismus, abnormal occlusal relationships, and facial deformities. The abnormalities were more severe in those patients who received radiation at an earlier age and at higher dosages. Possible chemotherapeutic effects in five of 23 patients who received treatment for tumors located outside the head and neck region comprised acquired amelogenesis imperfecta, microdontia of bicuspid teeth, and a tendency toward thinning of roots with an enlarged pulp chamber. Dental and maxillofacial abnormalities should be recognized as a major consequence of maxillofacial radiation in long-term survivors of childhood cancer, and attempts to minimize or eliminate such sequelae should involve an effective interaction between radiation therapists, and medical and dental oncologists

An all-polymer airflow sensor using a piezoresistive composite elastomer

International Nuclear Information System (INIS)

Aiyar, Avishek R; Allen, Mark G; Song, Chao; Kim, Seong-Hyok

2009-01-01

This paper presents an all-polymer flexible micromachined flow sensor using a carbon-black based conductive composite elastomer as a piezoresistor. The device is composed of an out-of-plane curved flow sensing element formed using a polyimide film. The conductive composite elastomer combines a low Young's modulus (∼1.72 MPa) and a high piezoresistive gage factor (∼7.3), making it an ideal material for the sensing application. Moreover, the use of the polyimide film, which can be easily laser micromachined, as the material for device fabrication enables the use of planar micromachining techniques, which minimizes process complexities. The proposed fabrication sequence combines the benefits of the polymeric materials used, while simultaneously enabling a backside interconnect scheme for an array of devices, without additional processing steps. The backside interconnect scheme allows for flow field mapping with minimum interference due to the sensing circuitry. Individual sensors as small as 1.5 mm in length and 0.4 mm in width, with 70 µm wide and 20–50 µm thick piezoresistor lines, have been fabricated. Wind tunnel testing demonstrated sensitivities as high as 66Ω/(m s −1 ). The integration of polyimide films and conductive elastomers into a flow sensing device using the simple planar fabrication technologies discussed is suitable for reduced cost, large area sensor array development, and can also leverage traditional flexible circuit fabrication

Friction of elastomer-on-glass system and direct observation of its frictional interface

International Nuclear Information System (INIS)

Okamoto, Yoshihiro; Nishio, Kazuyuki; Sugiura, Jun-ichi; Hirano, Motohisa; Nitta, Takahiro

2007-01-01

We performed a study on the static friction of PDMS elastomers with well-defined surface topography sliding over glass. An experimental setup for simultaneous measurements of friction force and direct observations of frictional interface has been developed. The static friction force was nearly proportional to normal load. The static friction force was independent of stick time. The simultaneous measurements revealed that the static friction force was proportional to the total area of contact. The coefficient was nearly independent of the surface topography of PDMS elastomers

Addressing Gender Discrimination in Oral and Maxillofacial Surgery via the Social Norms Approach.

Science.gov (United States)

Uppgaard, Rachel

2018-03-28

Gender discrimination continues to be a challenge faced by women in oral and maxillofacial surgery. The discrimination itself is perpetrated by a small number of individuals, but it is lack of support and intervention by other surgeons that allows this to continue. The social norms approach is one means to break this cycle: first by identifying misperceptions and then by encouraging individuals to intervene instead of remaining bystanders. To move forward as a specialty, we must actively intervene when discrimination and harassment occur. Copyright © 2018 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

Superhydrophobic/superoleophilic magnetic elastomers by laser ablation

Energy Technology Data Exchange (ETDEWEB)

Milionis, Athanasios, E-mail: am2vy@virginia.edu [Smart Materials-Nanophysics, Istituto Italiano di Tecnologia (IIT), Via Morego 30, 16163 Genova (Italy); Fragouli, Despina; Brandi, Fernando; Liakos, Ioannis; Barroso, Suset [Smart Materials-Nanophysics, Istituto Italiano di Tecnologia (IIT), Via Morego 30, 16163 Genova (Italy); Ruffilli, Roberta [Nanochemistry, Istituto Italiano di Tecnologia (IIT), Via Morego 30, 16163 Genova (Italy); Athanassiou, Athanassia, E-mail: athanassia.athanassiou@iit.it [Smart Materials-Nanophysics, Istituto Italiano di Tecnologia (IIT), Via Morego 30, 16163 Genova (Italy)

2015-10-01

Highlights: • We report the development of magnetic nanocomposite sheets. • Laser irradiation of the nanocomposites induces chemical and structural changes to the surface. • The laser-patterned surfaces exhibit superhydrophobicity and superoleophilicity. • The particle contribution in altering the surface and bulk properties of the material is studied. - Abstract: We report the development of magnetic nanocomposite sheets with superhydrophobic and supeoleophilic surfaces generated by laser ablation. Polydimethylsiloxane elastomer free-standing films, loaded homogeneously with 2% wt. carbon coated iron nanoparticles, were ablated by UV (248 nm), nanosecond laser pulses. The laser irradiation induces chemical and structural changes (both in micro- and nano-scale) to the surfaces of the nanocomposites rendering them superhydrophobic. The use of nanoparticles increases the UV light absorption efficiency of the nanocomposite samples, and thus facilitates the ablation process, since the number of pulses and the laser fluence required are greatly reduced compared to the bare polymer. Additionally the magnetic nanoparticles enhance significantly the superhydrophobic and oleophilic properties of the PDMS sheets, and provide to PDMS magnetic properties making possible its actuation by a weak external magnetic field. These nanocomposite elastomers can be considered for applications requiring magnetic MEMS for the controlled separation of liquids.

The dynamic contact area of elastomers at different velocities

NARCIS (Netherlands)

Khafidh, Muhammad; Rodriguez, N.V.; Masen, Marc Arthur; Schipper, Dirk J.

2016-01-01

The friction in tribo-systems that contain viscoelastic materials, such as elastomers, is relevant for a large number of applications. Examples include tyres, hoses, transmission and conveyor belts. To quantify the friction in these applications, one must first understand the contact behaviour of

Polycarbonate-based polyurethane elastomers: temperature-dependence of tensile properties

Czech Academy of Sciences Publication Activity Database

Hrdlička, Z.; Kuta, A.; Poreba, Rafal; Špírková, Milena

2014-01-01

Roč. 68, č. 2 (2014), s. 233-238 ISSN 0366-6352 R&D Projects: GA ČR GAP108/10/0195 Institutional support: RVO:61389013 Keywords : polyurethane * elastomer * polycarbonate diol Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.468, year: 2014

Effect of plasticiser on properties of styrene-butadiene-styrene thermoplastic elastomers

International Nuclear Information System (INIS)

Norzalia, S.; Farid, A.S.; O'Brien, M.G.

1999-01-01

This study investigates the properties of plasticised styrene-butadiene-styrene thermoplastic elastomers for possible applications in pharmaceutical, medical and food industries. Unplasticised styrene-butadiene-styrene (USBS) materials: vector 8550-D and vector 4461-D, which are developmental materials introduced by Exxon, and blends of vector 8550-D with vector 4461-D were plasticised paraffinic type plasticisers plastol 172 and plastol 352. Shore A hardness, tensile stress at break, modulus at 100% strain, elongation at break and density values showed a decrease whereas flow properties such as melt flow index (MFI) increased considerably with increasing plasticiser concentration. The properties of the plasticised styrene-butadiene-styrene thermoplastic elastomers were compared to the USBS materials. (author)

The Temporalis Muscle Flap in Maxillofacial Reconstruction

International Nuclear Information System (INIS)

ElSheikh, M; Zeitoun, I; ElMassry, M A K

1991-01-01

The temporalis muscle flap is a very versatile and valuable axial flap, which could be used in various reconstructive procedures in and around the oro-maxillofacial region. The surgical anatomy, vascular pattern and technique of elevation of the flap are described, together with our experience in different reconstructive situations. The advantages and disadvantages of the use of this flap are thoroughly discussed taking into consideration the potentiality of cancer recurrence under cover of the flap. (author)

Characterization of Ferrofluid-based Stimuli-responsive Elastomers

OpenAIRE

Sandra dePedro; Xavier Munoz-Berbel; Rosalia Rodríguez-Rodríguez; Jordi Sort; Jose Antonio Plaza; Juergen Brugger; Andreu Llobera; Victor J Cadarso

2016-01-01

Stimuli-responsive materials undergo physicochemical and/or structural changes when a specific actuation is applied. They are heterogeneous composites, consisting of a non-responsive matrix where functionality is provided by the filler. Surprisingly, the synthesis of polydimethylsiloxane (PDMS)-based stimuli-responsive elastomers (SRE) has seldomly been presented. Here, we present the structural, biological, optical, magnetic, and mechanical properties of several magnetic SRE (M-SRE) obtained...

Temporal change in the electromechanical properties of dielectric elastomer minimum energy structures

International Nuclear Information System (INIS)

Buchberger, G.; Hauser, B.; Jakoby, B.; Hilber, W.; Schoeftner, J.; Bauer, S.

2014-01-01

Dielectric elastomer minimum energy structures (DEMES) are soft electronic transducers and energy harvesters with potential for consumer goods. The temporal change in their electromechanical properties is of major importance for engineering tasks. Therefore, we study acrylic DEMES by impedance spectroscopy and by optical methods for a total time period of approx. 4.5 months. We apply either compliant electrodes from carbon black particles only or fluid electrodes from a mixture of carbon black particles and silicone oil. From the measurement data, the equivalent series capacitances and resistances as well as the bending angles of the transducers are obtained. We find that the equivalent series capacitances change in average between −12 %/1000 h and −4.0 %/1000 h, while the bending angles decrease linearly with slopes ranging from −15 %/1000 h to −7 %/1000 h. Transducers with high initial bending angles and electrodes from carbon black particles show the smallest changes of the electromechanical characteristics. The capacitances decrease faster for DEMES with fluid electrodes. Some DEMES of this type reveal huge and unpredictable fluctuations of the resistances over time due to the ageing of the contacts. Design guidelines for DEMES follow directly from the observed transient changes of their electromechanical performance.

Pattern of Maxillofacial fracture in Western and Central Nepal: An experience in 3 tertiary level health institutions

Directory of Open Access Journals (Sweden)

S Subedi

2015-06-01

Full Text Available BACKGROUND: There are only few studies regarding the pattern and causes of maxillofacial fractures till date in Nepal and no such study in western and central Nepalese population has been conducted. The purpose of this study, therefore, was to describe the causes and the pattern of maxillofacial fractures in western and central part of Nepal over the period of 5 years. MATERIAL AND METHODS A retrospective analysis of maxillofacial fractures was conducted on 328 patients who were treated in the department of maxillofacial surgery. Data was extracted and analyzed based on age, sex, cause of injury and anatomic location. RESULT Young males of 3rd decade of life most commonly sustained the maxillofacial trauma. The commonest site involved was the zygomatic complex (42% when only mid face fractures was considered and parasymphysis (32% when only mandible was considered.The most common cause of injuries was road traffic accidents (289 patients; 88.1% followed by interpersonal violence (25 patients; 7.6 % and falls accounting for 4.2% of the all injuries. CONCLUSION The findings of this study suggest the need for expansion of the motorway network, ensuring compliance of strict traffic rules and regulations, replacing old vehicles without safety measures and implement school education in alcohol abuse.DOI: http://dx.doi.org/10.3126/jcmsn.v10i3.12771 Journal of College of Medical Sciences-Nepal, 2014, Vol-10, No-3, 8-13

Radiation crosslinking of elastomers

International Nuclear Information System (INIS)

Pearson, D.S.

1981-01-01

In the first part of this paper a review is presented of recent results which show that the tensile strength and fatigue life of synthetic elastomers cured by radiation are essentially equivalent to those prepared by other crosslinking techniques. An explanation for the conflict of these new results with the earlier studies on natural rubber is presented. Investigations into the mechanisms and kinetics of crosslinking mentioned above have also shown that the irradiation method should be ideal for preparing well characterized networks. Such materials are useful for testing theoretical relationships between the structure of rubber networks and their stress-strain behavior. The second part of this paper is devoted to this aspect. (author)

To evaluate the efficacy of biodegradable plating system for fixation of maxillofacial fractures: A prospective study

OpenAIRE

Bali, Rishi K.; Sharma, Parveen; Jindal, Shalu; Gaba, Shivani

2013-01-01

Aims: The present study was undertaken to evaluate the efficacy of biodegradable plating system for fixation of maxillofacial fractures and to study the morbidity associated with the use of biodegradable plates and screws. Materials and Methods: This prospective study consisted of 10 patients with maxillofacial fractures requiring open reduction and internal fixation. Fractures with infection, comminuted and pathological fractures were excluded. All were plated with biodegradable system (Inio...

CT of maxillofacial injury

International Nuclear Information System (INIS)

DeLaPaz, R.; Brant-Zawadzki, M.; Rowe, L.D.

1986-01-01

Computed tomography has the ability to evaluate maxillofacial trauma quickly. The well-known contrast resolution capabilities of CT play a role in the usefulness of this modality. However, it is the image manipulation capability which is of singular advantage in these cases. The spatial resolution of computed tomography has matched that of conventional pluridirectional tomography in current generation equipment. Since a set of axial CT sections can be obtained with automatic table incrementation within 12 minutes, the information content per time of study ratio is improved over that of conventional tomography, despite the fact that image reformation requires extra time on the part of the radiologist. Radiation savings are significantly in favor of computed tomography as well. In the authors' experience, computed tomography is the primary diagnostic imaging modality used in the evaluation of complex facial trauma, after routine screening films are obtained

[3D planning in maxillofacial surgery].

Science.gov (United States)

Hoarau, R; Zweifel, D; Lanthemann, E; Zrounba, H; Broome, M

2014-10-01

The development of new technologies such as three-dimensional (3D) planning has changed the everyday practice in maxillofacial surgery. Rapid prototyping associated with the 3D planning has also enabled the creation of patient specific surgical tools, such as cutting guides. As with all new technologies, uses, practicalities, cost effectiveness and especially benefits for the patients have to be carefully evaluated. In this paper, several examples of 3D planning that have been used in our institution are presented. The advantages such as the accuracy of the reconstructive surgery and decreased operating time, as well as the difficulties have also been addressed.

[Modern technologies in cranio-maxillofacial surgery].

Science.gov (United States)

Lübbers, Heinz-Theo; Matthews, Felix; Kruse, Astrid L

2014-02-26

Modern technologies are influencing medicine everyday. The oral and maxillofacial surgery meet the worlds from medicine and dentistry. So technologies from both fields are utilized. This article provides an overview about technologies in clinical use, which are typical for the specialty. Their principles and indications are described as well as benefits and limitations. Based on Cone Beam Computed Tomography image fusion and mirroring techniques are explained as well as patient specific models and implants, template guided and free surgical navigation with and without intraoperative three-dimensional imaging. An overall assessment reveals further need of research regarding indications and patient benefit.

Haemangiomas of the maxillofacial region in Benin City, Nigeria ...

African Journals Online (AJOL)

Twenty-two patients with haemangiomas of the oro-facial region who presented at the department of Oral and Maxillofacial Surgery, UBTH, were studied. There was a preponderance of females (72.7%) over males (27.3%) and most (59.1%) patients were in the 11-31-year age group, with a median age of 25.0 years.

Preparation of magnetorheological elastomers and their slip-free characterization by means of parallel-plate rotational rheometry

Science.gov (United States)

Walter, Bastian L.; Pelteret, Jean-Paul; Kaschta, Joachim; Schubert, Dirk W.; Steinmann, Paul

2017-08-01

A systematic study is presented to highlight a methodology of sample preparation and subsequent slip-free characterization of magnetorheological (MR) elastomers in parallel-plate rotational rheometry. Focusing on the magnetic field-dependent nonlinear viscoelastic behavior an array of oscillatory strain sweep measurements is conducted with samples cured within the rheometer. The examined nonlinear material response (i.e. the amplitude dependence of the storage and loss moduli) as a function of the applied magnetic field is found to be qualitatively similar to the amplitude dependence of particle reinforced elastomers (i.e. the Payne effect). Therefore, the experimental data (both moduli) is decomposed similar to that for reinforced elastomers and a phenomenological model is formulated for both the storage and loss modulus to account for the physical mechanisms governing the nonlinear material characteristics. Parameter identification suggests that the material response at low magnetic fields is dominated by the polymeric network whereas the strong magneto-reinforced microstructure governs the linear and nonlinear viscoelastic behavior at high magnetic fields. The overall experimental outcome further suggests that the underlying concept of the phenomenological model for particle reinforced elastomers (i.e. destruction and reformation of the filler network) can be transfered to MR materials. Consequently, the proposed phenomenological model can be applied to quantify and further analyze the nonlinear response characteristics of MR elastomers (i.e. the amplitude dependence of the storage and loss modulus as a function of the applied magnetic field) that is closely linked to microstructural changes of the magnetizable particle network.

Gender trends in authorship in oral and maxillofacial surgery literature: A 30-year analysis.

Science.gov (United States)

Nkenke, Emeka; Seemann, Rudolf; Vairaktaris, Elefterios; Schaller, Hans-Günter; Rohde, Maximilian; Stelzle, Florian; Knipfer, Christian

2015-07-01

The aim of the present study was to perform a bibliometric analysis of the gender distribution of first and senior authorships in important oral and maxillofacial journals over the 30-year period from 1980 to 2010. Articles published in three representative oral and maxillofacial surgery journals were selected. The years 1980, 1990, 2000, and 2010 were chosen as representative points in time for article selection. Original research, case reports, technical notes, and reviews were included in the analysis. Case reports and technical notes were pooled in one group. For each article, the gender of the first author as well as that of the senior author was determined, based on the inspection of their first name. The type of article was determined and the country of origin of the article was documented. A total 1412 articles were subjected to the data analysis. A significant increase in female authorship in oral and maxillofacial surgery could be identified over the chosen 30-year period. However, the number of publications by male authors was still significantly higher at all points of time, exceeding those of female authors by at least 3.8 fold in 2010. As there is a trend towards feminization of medicine and dentistry, the results of the present study may serve as the basis for further analysis of the current situation, and the identification of necessary actions to accelerate the closure of the gender gap in publishing in oral and maxillofacial surgery. Copyright © 2015 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Evaluation of the scope and practice of oral and maxillofacial ...

African Journals Online (AJOL)

2014-11-27

Nov 27, 2014 ... that developed as a result of the need to treat servicemen injured in ... for effective organization of training, health care planning .... Similarly McNally found 5% female applicants to oral and ... maxillofacial surgeons in Australia worked in both private .... Glass ceiling, preference, prejudice or cohort effect?

Modeling shape selection of buckled dielectric elastomers

Science.gov (United States)

Langham, Jacob; Bense, Hadrien; Barkley, Dwight

2018-02-01

A dielectric elastomer whose edges are held fixed will buckle, given a sufficiently applied voltage, resulting in a nontrivial out-of-plane deformation. We study this situation numerically using a nonlinear elastic model which decouples two of the principal electrostatic stresses acting on an elastomer: normal pressure due to the mutual attraction of oppositely charged electrodes and tangential shear ("fringing") due to repulsion of like charges at the electrode edges. These enter via physically simplified boundary conditions that are applied in a fixed reference domain using a nondimensional approach. The method is valid for small to moderate strains and is straightforward to implement in a generic nonlinear elasticity code. We validate the model by directly comparing the simulated equilibrium shapes with the experiment. For circular electrodes which buckle axisymetrically, the shape of the deflection profile is captured. Annular electrodes of different widths produce azimuthal ripples with wavelengths that match our simulations. In this case, it is essential to compute multiple equilibria because the first model solution obtained by the nonlinear solver (Newton's method) is often not the energetically favored state. We address this using a numerical technique known as "deflation." Finally, we observe the large number of different solutions that may be obtained for the case of a long rectangular strip.

Soft Dielectric Elastomer Oscillators Driving Bioinspired Robots.

Science.gov (United States)

Henke, E-F Markus; Schlatter, Samuel; Anderson, Iain A

2017-12-01

Entirely soft robots with animal-like behavior and integrated artificial nervous systems will open up totally new perspectives and applications. To produce them, we must integrate control and actuation in the same soft structure. Soft actuators (e.g., pneumatic and hydraulic) exist but electronics are hard and stiff and remotely located. We present novel soft, electronics-free dielectric elastomer oscillators, which are able to drive bioinspired robots. As a demonstrator, we present a robot that mimics the crawling motion of the caterpillar, with an integrated artificial nervous system, soft actuators and without any conventional stiff electronic parts. Supplied with an external DC voltage, the robot autonomously generates all signals that are necessary to drive its dielectric elastomer actuators, and it translates an in-plane electromechanical oscillation into a crawling locomotion movement. Therefore, all functional and supporting parts are made of polymer materials and carbon. Besides the basic design of this first electronic-free, biomimetic robot, we present prospects to control the general behavior of such robots. The absence of conventional stiff electronics and the exclusive use of polymeric materials will provide a large step toward real animal-like robots, compliant human machine interfaces, and a new class of distributed, neuron-like internal control for robotic systems.

Liquid crystal elastomer coatings with programmed response of surface profile

NARCIS (Netherlands)

Babakhanova, G.; Turiv, T.; Guo, Y.; Hendrikx, M.; Wei, Q.H.; Schenning, A.P.H.J.; Broer, D.J.; Lavrentovich, O.D.

2018-01-01

Stimuli-responsive liquid crystal elastomers with molecular orientation coupled to rubber-like elasticity show a great potential as elements in soft robotics, sensing, and transport systems. The orientational order defines their mechanical response to external stimuli, such as thermally activated

Nonlinear electroelastic deformations of dielectric elastomer composites: II - Non-Gaussian elastic dielectrics

Science.gov (United States)

Lefèvre, Victor; Lopez-Pamies, Oscar

2017-02-01

This paper presents an analytical framework to construct approximate homogenization solutions for the macroscopic elastic dielectric response - under finite deformations and finite electric fields - of dielectric elastomer composites with two-phase isotropic particulate microstructures. The central idea consists in employing the homogenization solution derived in Part I of this work for ideal elastic dielectric composites within the context of a nonlinear comparison medium method - this is derived as an extension of the comparison medium method of Lopez-Pamies et al. (2013) in nonlinear elastostatics to the coupled realm of nonlinear electroelastostatics - to generate in turn a corresponding solution for composite materials with non-ideal elastic dielectric constituents. Complementary to this analytical framework, a hybrid finite-element formulation to construct homogenization solutions numerically (in three dimensions) is also presented. The proposed analytical framework is utilized to work out a general approximate homogenization solution for non-Gaussian dielectric elastomers filled with nonlinear elastic dielectric particles that may exhibit polarization saturation. The solution applies to arbitrary (non-percolative) isotropic distributions of filler particles. By construction, it is exact in the limit of small deformations and moderate electric fields. For finite deformations and finite electric fields, its accuracy is demonstrated by means of direct comparisons with finite-element solutions. Aimed at gaining physical insight into the extreme enhancement in electrostriction properties displayed by emerging dielectric elastomer composites, various cases wherein the filler particles are of poly- and mono-disperse sizes and exhibit different types of elastic dielectric behavior are discussed in detail. Contrary to an initial conjecture in the literature, it is found (inter alia) that the isotropic addition of a small volume fraction of stiff (semi

New maxillofacial infrared detection technologies

Energy Technology Data Exchange (ETDEWEB)

Reshetnikov, A. P.; Kopylov, M. V.; Nasyrov, M. R., E-mail: marat.1994@me.com; Fisher, E. L.; Chernova, L. V. [Izhevsk State Medical Academy, Izhevsk, Russia (426034, Izhevsk, Kommunarov street, 281) (Russian Federation); Soicher, E. M. [Moscow State University of Medicine and Dentistry named after A.I. Evdokimov of the Ministry of Health of the Russian Federation, Moscow, Russia, (127473, Moscow, Delegatskaya str., 20/1) (Russian Federation)

2015-11-17

At the dental clinic the infrared range radiation spectrum of tissues was used to study the dynamics of local temperature and structure of the skin, subcutaneous fat, and other tissues of the maxillofacial area in adult healthy volunteers and patients. In particular, we studied the dynamics of local temperature of mucous membranes of the mouth, teeth, and places in the mouth and dental structures in the norm and in various pathological conditions of the lips, gums, teeth, tongue, palate, and cheeks before, during and after chewing food, drinking water, medication, and inhalation of air. High safety and informational content of infrared thermography are prospective for the development of diagnostics in medicine. We have 3 new methods for infrared detection protected by patents in Russia.

The use of optical coherence tomography in maxillofacial surgery

Science.gov (United States)

Al-Obaidi, Mohammed; Tandon, Rahul; Tiwana, Paul

2015-02-01

The ever-evolving medical field continues to trend toward less invasive approaches to the diagnosis and treatment of pathological conditions. Basic sciences research has allowed for improved technologies that are translated to the clinical sciences. Similarly, advancements in imaging modalities continue to improve and their applications become more varied. As such, surgeons and pathologists are able to depend on smaller samples for tissue diagnosis of pathological disease, where once large sections of tissue were needed. Optical coherence tomography (OCT), a high-resolution imaging technique, has been used extensively in different medical fields to improve diagnostic yield. Its use in dental fields, particularly in oral and maxillofacial surgery, remains limited. Our goal is to assess the use of OCT for improving soft tissue analysis and diagnosis, particularly for its applications in the field of oral and maxillofacial surgery. Optical coherence tomography is a modality that uses an optical signal using safe near-infrared light which is reflected off the sub-surface structures. This allows for high-resolution cross-sectional images of the tissue morphology to be obtained. Ophthalmologists have been using OCT to obtain images of the retina to assess for age-related macular degeneration. More recently, OCT has been used by Interventional Cardiology to image coronary arteries, and assess plaque thickness and morphology. This technology is now being investigated in several medical fields as a form of optical biopsy, providing in situ images with high-resolution morphology of tissues. We are particularly interested in its use on epithelial tissues, and therefore performed a literature review on the use of OCT for assessing epithelium. Evaluation of histologically-diagnosed actinic keratosis, for example, was found to correlate well with the imaging discrepancies found on OCT; and the in vivo assessment of atypical keratinocytes was firmly established. Additionally

A nonaffine network model for elastomers undergoing finite deformations

Science.gov (United States)

Davidson, Jacob D.; Goulbourne, N. C.

2013-08-01

In this work, we construct a new physics-based model of rubber elasticity to capture the strain softening, strain hardening, and deformation-state dependent response of rubber materials undergoing finite deformations. This model is unique in its ability to capture large-stretch mechanical behavior with parameters that are connected to the polymer chemistry and can also be easily identified with the important characteristics of the macroscopic stress-stretch response. The microscopic picture consists of two components: a crosslinked network of Langevin chains and an entangled network with chains confined to a nonaffine tube. These represent, respectively, changes in entropy due to thermally averaged chain conformations and changes in entropy due to the magnitude of these conformational fluctuations. A simple analytical form for the strain energy density is obtained using Rubinstein and Panyukov's single-chain description of network behavior. The model only depends on three parameters that together define the initial modulus, extent of strain softening, and the onset of strain hardening. Fits to large stretch data for natural rubber, silicone rubber, VHB 4905 (polyacrylate rubber), and b186 rubber (a carbon black-filled rubber) are presented, and a comparison is made with other similar constitutive models of large-stretch rubber elasticity. We demonstrate that the proposed model provides a complete description of elastomers undergoing large deformations for different applied loading configurations. Moreover, since the strain energy is obtained using a clear set of physical assumptions, this model may be tested and used to interpret the results of computer simulation and experiments on polymers of known microscopic structure.

[Correction of congenital malformations by custom-made silicone implants: Contribution of computer-aided design. Experience of 611 cases].

Science.gov (United States)

Chavoin, J P; Chaput, B; Garrido, I; Moreno, B; Dahan, M; Grolleau, J L

2016-10-01

Modern techniques of computer-aided design and tridimensional prototyping for manufacturing silicone elastomer custom implants are growing. They have widely modified the surgical indications in our unit. By presenting their experience of 611 cases managed between 1993 and 2016, the authors describe the method of conception from CT-scans, the virtual image of the body and the manufacture of the custom-made implant perfectly adapted to the anatomy of each one. The operative techniques are described for the three main indications: the funnel chest or pectus excavatum (474 cases) according to a modified CHIN classification is corrected simply and very satisfactorily. This approach may render thoracic surgery techniques obsolete. Indeed, these operations remain risky and of doubtful functional utility; Poland syndrome (116 cases), where the use of a custom-made implant for compensation of muscle volume is frequently used, but can be improved by a transfer of adipose tissue or a classic breast implant; the leg atrophies (21 cases) receive custom elastomer implants introduced in a sub-fascial plane. The results are excellent for pectus excavatum but more difficult to optimize for the other two indications, requiring sometimes complementary techniques. Complications are rare and often benign, implants endure for life. Quality of life, psychological comfort and self-esteem have been improved with low morbidity and without having undergone a painful surgical experience. Reconstructive procedures of congenital malformations by custom-made silicone implants open a new field of activity for our surgical specialty with vast opportunities. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

Development of procedures for calculating stiffness and damping properties of elastomers in engineering applications. Part 1: Verification of basic methods

Science.gov (United States)

Chiang, T.; Tessarzik, J. M.; Badgley, R. H.

1972-01-01

The primary aim of this investigation was verification of basic methods which are to be used in cataloging elastomer dynamic properties (stiffness and damping) in terms of viscoelastic model constants. These constants may then be used to predict dynamic properties for general elastomer shapes and operating conditions, thereby permitting optimum application of elastomers as energy absorption and/or energy storage devices in the control of vibrations in a broad variety of applications. The efforts reported involved: (1) literature search; (2) the design, fabrication and use of a test rig for obtaining elastomer dynamic test data over a wide range of frequencies, amplitudes, and preloads; and (3) the reduction of the test data, by means of a selected three-element elastomer model and specialized curve fitting techniques, to material properties. Material constants thus obtained have been used to calculate stiffness and damping for comparison with measured test data. These comparisons are excellent for a number of test conditions and only fair to poor for others. The results confirm the validity of the basic approach of the overall program and the mechanics of the cataloging procedure, and at the same time suggest areas in which refinements should be made.

A review of computer-aided oral and maxillofacial surgery: planning, simulation and navigation.

Science.gov (United States)

Chen, Xiaojun; Xu, Lu; Sun, Yi; Politis, Constantinus

2016-11-01

Currently, oral and maxillofacial surgery (OMFS) still poses a significant challenge for surgeons due to the anatomic complexity and limited field of view of the oral cavity. With the great development of computer technologies, he computer-aided surgery has been widely used for minimizing the risks and improving the precision of surgery. Areas covered: The major goal of this paper is to provide a comprehensive reference source of current and future development of computer-aided OMFS including surgical planning, simulation and navigation for relevant researchers. Expert commentary: Compared with the traditional OMFS, computer-aided OMFS overcomes the disadvantage that the treatment on the region of anatomically complex maxillofacial depends almost exclusively on the experience of the surgeon.

Use of customized polyetheretherketone (PEEK) implants in the reconstruction of complex maxillofacial defects.

Science.gov (United States)

Kim, Michael M; Boahene, Kofi D O; Byrne, Patrick J

2009-01-01

Extensive maxillofacial defects resulting from trauma or oncologic resection present reconstructive challenges. Various autografts and alloplastic materials in conjunction with standard soft-tissue techniques have been used in the reconstruction of these types of defects. Polyetheretherketone (PEEK) is a semicrystalline polyaromatic linear polymer exhibiting an excellent combination of strength, stiffness, durability, and environmental resistance. Recent investigations of PEEK as a biomaterial resulted in the successful treatment of cervical disk disease. We describe a series of 4 patients whose defects were reconstructed using customized PEEK implants. All had excellent postoperative aesthetic and functional results without complications such as infections or extrusions. Because PEEK implants are customizable, easily workable, inert, and nonporous, they represent an ideal alloplastic material for maxillofacial reconstruction.

Kinetic limitation in the formation of end-linked elastomer networks

Czech Academy of Sciences Publication Activity Database

Meissner, Bohumil; Matějka, Libor

2005-01-01

Roč. 46, č. 24 (2005), s. 10618-10625 ISSN 0032-3861 R&D Projects: GA ČR GA203/05/2252 Keywords : end-linked elastomer networks * effect of stoichiometry * kinetic limitations Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.849, year: 2005

A smart experimental technique for the optimization of dielectric elastomer actuator (DEA) systems

International Nuclear Information System (INIS)

Hodgins, M; Rizzello, G; York, A; Seelecke, S; Naso, D

2015-01-01

In order to aid in moving dielectric elastomer actuator (DEA) technology from the laboratory into a commercial product DEA prototypes should be tested against a variety of loading conditions and eventually in the end user conditions. An experimental test setup to seamlessly perform mechanical characterization and loading of the DEA would be a great asset toward this end. Therefore, this work presents the design, control and systematic validation of a benchtop testing station for miniature silicon based circular DEAs. A versatile benchtop tester is able to characterize and apply programmable loading forces to the DEA while measuring actuator performance. The tester successfully applied mechanical loads to the DEA (including positive, constant and negative stiffness loads) simulating biasing systems via an electromagnetic linear motor operating in closed loop with a force/mechanical impedance control scheme. The tester expedites mechanical testing of the DEA by eliminating the need to build intricate pre-load mechanisms or use multiple testing jigs for characterizing the DEA response. The results show that proper mechanical loading of the DEA increases the overall electromechanical sensitivity of the system and thereby the actuator output. This approach to characterize and apply variable loading forces to DEAs in a single test system will enable faster realization of higher performance actuators. (paper)

Batch fabrication of optical actuators using nanotube-elastomer composites towards refreshable Braille displays

Science.gov (United States)

Camargo, C. J.; Campanella, H.; Marshall, J. E.; Torras, N.; Zinoviev, K.; Terentjev, E. M.; Esteve, J.

2012-07-01

This paper reports an opto-actuable device fabricated using micro-machined silicon moulds. The actuating component of the device is made from a composite material containing carbon nanotubes (CNTs) embedded in a liquid crystal elastomer (LCE) matrix. We demonstrate the fabrication of a patterned LCE-CNT film by a combination of mechanical stretching and thermal cross-linking. The resulting poly-domain LCE-CNT film contains ‘blister-shaped’ mono-domain regions, which reversibly change their shape under light irradiation and hence can be used as dynamic Braille dots. We demonstrate that blisters with diameters of 1.0 and 1.5 mm, and wall thickness 300 µm, will mechanically contract under irradiation by a laser diode with optical power up to 60 mW. The magnitude of this contraction was up to 40 µm, which is more than 10% of their height in the ‘rest’ state. The stabilization time of the material is less than 6 s for both actuation and recovery. We also carried out preliminary tests on the repeatability of this photo-actuation process, observing no material or performance degradation. This manufacturing approach establishes a starting point for the design and fabrication of wide-area tactile actuators, which are promising candidates for the development of new Braille reading applications for the visually impaired.

Inverse grey-box model-based control of a dielectric elastomer actuator

DEFF Research Database (Denmark)

Jones, Richard William; Sarban, Rahimullah

2012-01-01

control performance across the operating range of the DE actuator, a gain scheduling term, which linearizes the operating characteristics of the tubular dielectric elastomer actuator, is developed and implemented in series with the IMC controller. The IMC-based approach is investigated for servo control......An accurate physical-based electromechanical model of a commercially available tubular dielectric elastomer (DE) actuator has been developed and validated. In this contribution, the use of the physical-based electromechanical model to formulate a model-based controller is examined. The choice...... of control scheme was dictated by the desire for transparency in both controller design and operation. The internal model control (IMC) approach was chosen. In this particular application, the inverse of the linearized form of the grey-box model is used to formulate the IMC controller. To ensure consistent...

COMPLICATIONS OF ORAL AND MAXILLOFACIAL SURGERY UNDER GENERAL ANESTHESIA IN TUBE-FED CHILDREN: A RETROSPECTIVE ANALYSIS.

Science.gov (United States)

Nguyen, Trang D; Freilich, Marshall M; Macpherson, Bruce A

2016-06-01

To assess morbidity and mortality associated with oral and maxillofacial surgery procedures requiring general anesthesia among children with aspiration tendency requiring enteral feeding. A retrospective chart review was conducted of children surgically treated under general anesthesia by the oral and maxillofacial surgery service at the Hospital for Sick Children in Toronto, Canada. Medical and dental records over a 9-year period (January 1, 2000 to January 1, 2010) were reviewed. Data were collected on demographics, primary illness, coexisting medical conditions, procedures performed, medications administered, type of airway management used, duration of general anesthesia, American Society of Anesthesiologists' physical status classification and adverse events. During the period reviewed, 28 children underwent 35 oral and maxillofacial surgery procedures under general anesthesia. The mean patient age was 12 years (range 4-17 years). No deaths occurred. Of the 35 surgeries, 10 (29%) were associated with at least 1adverse event. Adverse events included 1incident of respiratory distress, 2incidents of fever, 5incidents of bleeding, 1incident of seizure and 4incidents of oxygen saturation below 90% for more than 30s. Children with a history of aspiration tendency that necessitates enteral feeding, who undergo oral and maxillofacial surgery under general anesthesia, are at increased risk of morbidity. Before initiating treatment, the surgeon and parents or guardians of such children should carefully consider these risks compared with the anticipated benefit of surgery.

Micro-vibration response of a stochastically excited sandwich beam with a magnetorheological elastomer core and mass

International Nuclear Information System (INIS)

Ying, Z G; Ni, Y Q

2009-01-01

Magnetorheological (MR) elastomers are used to construct a smart sandwich beam for micro-vibration control. The micro-vibration response of a clamped–free sandwich beam with an MR elastomer core and a supplemental mass under stochastic support micro-motion excitation is studied. The dynamic behavior of MR elastomer as a smart viscoelastic material is described by a complex modulus which is controllable by external magnetic field. The sixth-order partial differential equation of motion of the sandwich beam is derived from the dynamic equilibrium, constitutive and geometric relations. A frequency-domain solution method for the stochastic micro-vibration response of the sandwich beam is developed by using the frequency-response function, power spectral density function and spatial eigensolution. The root-mean-square velocity response in terms of the one-third octave frequency band is calculated, and then the response reduction capacity through optimizing the complex modulus of the core is analyzed. Numerical results illustrate the influences of the MR elastomer core parameters on the root-mean-square velocity response and the high response reduction capacity of the sandwich beam. The developed analysis method is applicable to sandwich beams with arbitrary cores described by complex shear moduli under arbitrary stochastic excitations described by power spectral density functions

Preparation and demonstration of poly(dopamine)-triggered attapulgite-anchored polyurethane as a high-performance rod-like elastomer to reinforce soy protein-isolated composites

Science.gov (United States)

Zhao, Shujun; Wen, Yingying; Wang, Zhong; Kang, Haijiao; Li, Jianzhang; Zhang, Shifeng; Ji, Yong

2018-06-01

Nanophase modification is an effective path to improve composite properties, however, it remains a great challenge to increase the mechanical strength of the modified materials without sacrificing elongation and toughness. This study presents a novel and efficient design for interface anchoring of a waterborne polyurethane (WPU) elastomer with attapulgite (ATP) triggered by poly(dopamine) (PDA) formation due to self-polymerization of the dopamine moieties. The WPU-PDA-ATP (WDA) rod-like elastomer served as an active enhancer for a soy protein isolate (SPI)-based composite to facilitate multiple interactions between SPI and the elastomer. As expected, the PDA layer was coated onto ATP, inducing the nanofiller to successfully anchor onto the WPU elastomer, as confirmed by solid-state 13C NMR, XPS, and ATR-FTIR results. Compared with the control SPI-based film, the tensile strength and toughness increased by 145.6% and 118.3% respectively by introducing WDA rod-like elastomer. The water resistance and thermal stability of the prepared SPI composites were also favorable. The proposed approach represents an efficient way to utilize high-performance elastomer in biobased materials to concurrently enhance strength and toughness.

Influence of the geometry on magnetic interactions in a retina fixator based on a magnetoactive elastomer seal

Science.gov (United States)

Nadzharyan, T. A.; Makarova, L. A.; Kazimirova, E. G.; Perov, N. S.; Kramarenko, E. Yu

2018-03-01

We study the effects the geometric configuration has on magnetic interactions between a magnetoactive elastomer (MAE) sample and various systems of permanent magnets for problems with both flat and curved geometry. MAEs consist of a silicone polymer matrix and iron filler microparticles embedded in it. Permanent magnets are cylindrical neodymium magnets arranged in a line on a flat or curved solid surfaces. We use computer simulations, namely the finite element method, in order to study the interaction force and magnetic pressure in a system with an MAE sample and permanent magnets. The model is based on classical Maxwell magnetostatics and two factors taking into account field dependence of MAE’s magnetic properties and inhomogeneities caused by local demagnetization. We calculate magnetic pressure dependences on various geometric parameters of the system, namely, the diameter and the height of permanent magnets, the distance between the magnets and dimensions of MAE samples. This research aims to create a set of guidelines for choosing the geometric configuration of a retina fixator based on MAE seals to be used in eye surgery for retinal detachment treatment.

Maxillofacial and mandibular phenotypes in the skulls of red Sokoto ...

African Journals Online (AJOL)

This work examined phenotypic expressions in the anatomy of the mandible and maxillofacial region of the Red Sokoto and Sahel goats in Nigeria. The infraorbital foramen was placed above premolar two (PM2) in Red Sokoto but above premolar one (PM1) in Sahel. The Red Sokoto displayed interdigital septa (ruggae) ...

The static actuation of dielectric elastomer actuators: how does pre-stretch improve actuation?

International Nuclear Information System (INIS)

Kofod, Guggi

2008-01-01

It has previously been shown that providing dielectric elastomer actuators with a level of pre-stretch can improve properties such as breakdown strength, actuation strain and efficiency. The actuation in such actuators depends on an interplay between the highly nonlinear hyperelastic stress-strain behaviour with the electrostatic Maxwell's stress; however, the direct effects of pre-stretch on the electromechanical coupling have still not been investigated in detail. We compare several experimental results found in the literature on the hyperelastic parameters of the Ogden model for the commonly used material VHB 4910, and introduce a more detailed and thus more accurate fit to a previous uniaxial stress-strain experiment. Electrostatic actuation models for a pure shear cuboid dielectric elastomer actuator with pre-stretch are introduced, for both intensive and extensive variables. For both intensive and extensive variables the constant strain (blocked stress or force) as well as the actuation strain is presented. It is shown how in the particular case of isotropic amorphous elastomers the pre-stretch does not affect the electromechanical coupling directly, and that the enhancement in actuation strain due to pre-stretch occurs through the alteration of the geometrical dimensions of the actuator. Also, the presence of the optimum load is explained as being due to the plateau region in the force-stretch curve, and it is shown that pre-stretch is not able to affect its position. Finally, it is shown how the simplified Ogden fit leads to entirely different conclusions for actuation strain in terms of extensive variables as does the detailed fit, emphasizing the importance of employing accurate hyperelastic models for the stress-stretch behaviour of the elastomer.

Assessment of the effective dose in supine, prone, and oblique positions in the maxillofacial region using a novel combined extremity and maxillofacial cone beam computed tomography scanner

NARCIS (Netherlands)

Koivisto, J.; Wolff, J.; Järnstedt, J.; Dastidar, P.; Kortesniemi, M.

2014-01-01

Objective The objectives of this study were to assess the organ and effective doses (International Commission on Radiological Protection [ICRP] 103 standard) resulting from supine, prone, and oblique phantom positions in the maxillofacial region using a novel cone beam computed tomography (CBCT)

Evaluation of Ultrasonography as a Diagnostic Tool in Maxillofacial Space Infections

Directory of Open Access Journals (Sweden)

Praveen Kumar Pandey

2011-11-01

Full Text Available Objectives: The purpose of the study was to establish the role of ultrasonography in determining the involvement of specific fascial spaces in maxillofacial region and the stage of infection, in indicating the appropriate time for surgical intervention and to compare clinical and ultrasonographic findings.Material and Methods: Twenty five patients with fascial space infection in maxillofacial region were subjected to ultrasonographic examination following a detailed clinical and radiological examination. Ultrasonography guided needle aspiration was performed. Based on the findings, patients diagnosed with abscess were subjected to incision and drainage and those with cellulitis were subjected to medical line of treatment.Results: More than one fascial space was involved in all patients. On clinical examination 64 spaces were involved, of them 34 spaces had abscess formation and 30 spaces were in the stage of cellulitis. On ultrasonography examination, 28 spaces were reported to have abscess formation and 36 spaces were diagnosed to be in the stage of cellulitis. On comparative analysis of both clinical and ultrasonographic findings, ultrasonography was found to be sensitive in 65% of the cases and having specificity of 80%. It was registered statistically significant (P < 0.001 agreement between these two methods of assessment (kappa index = 0.814.Conclusions: Ultrasonography is a quick, widely available, relatively inexpensive, and painless procedure and can be repeated as often as necessary without risk to the patient. Thus ultrasonography is a valuable diagnostic aid to the oral and maxillofacial surgeon for early and accurate diagnosis of fascial space infection, their appropriate treatment and to limit their further spread.

Triboelectric-Nanogenerator-Based Soft Energy-Harvesting Skin Enabled by Toughly Bonded Elastomer/Hydrogel Hybrids.

Science.gov (United States)

Liu, Ting; Liu, Mengmeng; Dou, Su; Sun, Jiangman; Cong, Zifeng; Jiang, Chunyan; Du, Chunhua; Pu, Xiong; Hu, Weiguo; Wang, Zhong Lin

2018-03-27

A major challenge accompanying the booming next-generation soft electronics is providing correspondingly soft and sustainable power sources for driving such devices. Here, we report stretchable triboelectric nanogenerators (TENG) with dual working modes based on the soft hydrogel-elastomer hybrid as energy skins for harvesting biomechanical energies. The tough interfacial bonding between the hydrophilic hydrogel and hydrophobic elastomer, achieved by the interface modification, ensures the stable mechanical and electrical performances of the TENGs. Furthermore, the dehydration of this toughly bonded hydrogel-elastomer hybrid is significantly inhibited (the average dehydration decreases by over 73%). With PDMS as the electrification layer and hydrogel as the electrode, a stretchable, transparent (90% transmittance), and ultrathin (380 μm) single-electrode TENG was fabricated to conformally attach on human skin and deform as the body moves. The two-electrode mode TENG is capable of harvesting energy from arbitrary human motions (press, stretch, bend, and twist) to drive the self-powered electronics. This work provides a feasible technology to design soft power sources, which could potentially solve the energy issues of soft electronics.

CBCT images of anatomic landmarks in maxillofacial region

OpenAIRE

Mayil, Meltem; Keser, Gaye; Namdar Pekiner, Filiz

2014-01-01

Conventional radiographic techniques in dental radiology allows only 2D images of 3D structures of head and neck region. CBCT is a recent technology, is also named as dental volumetric tomography, which was developed as an alternative to conventional CT using cone beam-shaped X-ray to provide more rapid acquisition of a data set of entire maxillofacial region. CBCT has remarkable advantages such as shorter exposure time, reduced image distortion due to patient movements, dec...

Solubility of gases and solvents in silicon polymers: molecular simulation and equation of state modeling

DEFF Research Database (Denmark)

Economou, Ioannis; Makrodimitri, Zoi A.; Kontogeorgis, Georgios

2007-01-01

of gas and solvent solubilities using the test particle insertion method of Widom. Polymer chains are modelled using recently developed realistic atomistic force fields. Calculations are performed at various temperatures and ambient pressure. A crossover in the temperature dependence of solubility......) and also the phase equilibria of these mixtures over a wide composition range. In all cases, the agreement between model predictions/correlations and literature experimental data, when available, is excellent.......The solubility of n-alkanes, perfluoroalkanes, noble gases and light gases in four elastomer polymers containing silicon is examined based on molecular simulation and macroscopic equation of state modelling. Polymer melt samples generated from molecular dynamics ( MD) are used for the calculation...

Apparatus, system, and method for providing fabric-elastomer composites as pneumatic actuators

Science.gov (United States)

Martinez, Ramses V.; Whitesides, George M.

2017-10-25

Soft pneumatic actuators based on composites consisting of elastomers with embedded sheet or fiber structures (e.g., paper or fabric) that are flexible but not extensible are described. On pneumatic inflation, these actuators move anisotropically, based on the motions accessible by their composite structures. They are inexpensive, simple to fabricate, light in weight, and easy to actuate. This class of structure is versatile: the same principles of design lead to actuators that respond to pressurization with a wide range of motions (bending, extension, contraction, twisting, and others). Paper, when used to introduce anisotropy into elastomers, can be readily folded into three-dimensional structures following the principles of origami; these folded structures increase the stiffness and anisotropy of the elastomeric actuators, while keeping them light in weight.

Influence of surface modification on friction coefficient of the titanium-elastomer couple.

Science.gov (United States)

Chladek, Wiesław; Hadasik, Eugeniusz; Chladek, Grzegorz

2007-01-01

This paper presents the results of a study of the friction coefficient of titanium-elastomer couple. The study was carried out with a view to potential future utilization of its results for constructing retentive elements of implanted prostheses. Changes in the friction force were recorded while removing titanium specimens placed between two silicone counter specimens made of Ufi Gel. The influence of the titanium specimen movement speed in relation that of to the counter specimens and the influence of clamping force on the friction force were assessed. Additionally, the surface roughness of titanium specimens differed; in one case, titanium was coated with polyethylene. The effect of introducing artificial saliva between the cooperating surfaces on the friction force and friction coefficient was analyzed as well. Based on the characteristics recorded, the possibilities of shaping the friction coefficient have been assessed, since it is the friction coefficient that determines effective operation of a friction couple through increasing the titanium specimen roughness. The artificial saliva being introduced between the specimens reduces considerably the friction coefficient through a change of the phenomenon model. An increase in the pressure force for the specimens of high roughness entails a reduction of the friction coefficient. The study carried out allows us to identify the roughness parameters, which in turn will enable obtaining the prescribed retention force for friction/membrane couplings.

Cross-linking and modification of saturated elastomers using functionalized azides

NARCIS (Netherlands)

Zielinska, A.J.

2011-01-01

The main advantage of saturated elastomers, such as EPM and EPDM over their unsaturated counter-parts is the absence of carbon-carbon unsaturation in the main polymer chain, resulting in excellent ozone and heat resistance. A consequent disadvantage of the absence of unsaturation is the lack of

Body dysmorphic disorder screening in maxillofacial outpatients presenting for orthognathic surgery

NARCIS (Netherlands)

Vulink, N. C. C.; Rosenberg, A.; Plooij, J. M.; Koole, R.; Bergé, S. J.; Denys, D.

2008-01-01

Body dysmorphic disorder (BDD) is a severe psychiatric disease with delusions about defects in appearance for which patients seek surgical help. This is the first European study to determine the half-year prevalence of BDD in a maxillofacial outpatient clinic. A total of 160 patients with

Tattoos: could they be used to advantage as a medical alert in oral and maxillofacial surgery?

Science.gov (United States)

Colbert, S D; Brennan, P A

2017-04-01

Many publications have addressed the medical complications of tattoos, but to our knowledge there are no reports of their use to alert people in our field of potentially dangerous conditions. We present a new way to inform oral and maxillofacial colleagues about patients with a history of malignant hyperthermia (or any other life-threatening medical problem) and discuss the potential advantages and disadvantages of medical alert tattoos. Copyright © 2016 The British Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

In situ multi-axial loading frame to probe elastomers using X-ray scattering.

Science.gov (United States)

Pannier, Yannick; Proudhon, Henry; Mocuta, Cristian; Thiaudière, Dominique; Cantournet, Sabine

2011-11-01

An in situ tensile-shear loading device has been designed to study elastomer crystallization using synchrotron X-ray scattering at the Synchrotron Soleil on the DiffAbs beamline. Elastomer tape specimens of thickness 2 mm can be elongated by up to 500% in the longitudinal direction and sheared by up to 200% in the transverse direction. The device is fully automated and plugged into the TANGO control system of the beamline allowing synchronization between acquisition and loading sequences. Experimental results revealing the evolution of crystallization peaks under load are presented for several tension/shear loading sequences.

Laser tumor treatment in oral and maxillofacial surgery

Science.gov (United States)

Neukam, F. W.; Stelzle, F.

Cancer treatment is an integral part of oral and maxillofacial surgery. Oral cancer in particular is a highly prevalent neoplasm. Standard treatment for most of the tumors is radical surgery combined with stage-based neo-/adjuvant therapy. Laser surgery has become a reliable treatment option for oral cancer as well as for precancerous lesions. Widely used lasers in oral and maxillofacial tumor surgery are the CO2 laser, the Er:YAG laser, the Nd:YAG laser and the KTM laser. The use of lasers in tumor surgery has several advantages: remote application, precise cutting, hemostasis, low cicatrization, reduced postoperative pain and swelling, can be combined with endoscopic, microscopic and robotic surgery. However, laser surgery has some major drawbacks: In contrast to conventional incisions with scalpels, the surgeon gets no feedback during laser ablation. There is no depth sensation and no tissue specificity with a laser incision, increasing the risk of iatrogenic damage to nerves and major blood vessels. Future prospects may solve these problems by means of an optical feedback mechanism that provides a tissue-specific laser ablation. First attempts have been made to perform remote optical tissue differentiation. Additionally, real time optical tumor detection during laser surgery would allow for a very precise and straight forward cancer resection, enhancing organ preservation and hence the quality of life for patients with cancer in the head and neck region.

Dynamic- and Thermo- mechanical Analysis of Inorganic Nanotubes/elastomer Composites

Directory of Open Access Journals (Sweden)

Armin FUITH

2011-10-01

Full Text Available We present dynamic mechanical analysis (DMA and thermomechanical analysis (TMA measurements of a new type of polyurea elastomer nanocomposites based on inorganic MoS2 nanotubes and Mo6S2I8 nanowires. The addition of a small amount of nanoparticles (<1 wt-% leads to an increase of the glass transition temperature Tg as compared to the pure elastomeric matrix. A second peak observed in tand in the pure and mixed elastomer is attributed to a second glass transition occurring in regions near the hard nanodomains of the microphase separated polyurea system. It is also found that the small amount of nanoparticles leads to an increase in the Young´s modulus of up to 15 % in the whole measured temperature range (from -130 °C to 20 °C. The thermal expansion of doped samples is considerably larger above Tg. Below Tg, this difference vanishes completely. A very similar behaviour was also found in measurements of polyisoprene/multiwall carbon nanotube (MWCNT composites.

Shape-memory effect of nanocomposites based on liquid-crystalline elastomers

Science.gov (United States)

Marotta, A.; Lama, G. C.; Gentile, G.; Cerruti, P.; Carfagna, C.; Ambrogi, V.

2016-05-01

In this work, nanocomposites based on liquid crystalline (LC) elastomers were prepared and characterized in their shape memory properties. For the synthesis of materials, p-bis(2,3-epoxypropoxy)-α-methylstilbene (DOMS) was used as mesogenic epoxy monomer, sebacic acid (SA) as curing agent and multi-walled carbon nanotubes (MWCNT) and graphene oxide (GO) as fillers. First, an effective compatibilization methodology was set up to improve the interfacial adhesion between the matrix and the carbonaceous nanofillers, thus obtaining homogeneous distribution and dispersion of the nanofillers within the polymer phase. Then, the obtained nanocomposite films were characterized in their morphological and thermal properties. In particular, the effect of the addition of the nanofillers on liquid crystalline behavior, as well as on shape-memory properties of the realized materials was investigated. It was found that both fillers were able to enhance the thermomechanical response of the LC elastomers, making them good candidates as shape memory materials.

A mechanical characterisation on multiple timescales of electroconductive magnetorheological elastomers

Science.gov (United States)

Schümann, M.; Morich, J.; Kaufhold, T.; Böhm, V.; Zimmermann, K.; Odenbach, S.

2018-05-01

Magnetorheological elastomers are a type of smart hybrid material which combines elastic properties of a soft elastomer matrix with magnetic properties of magnetic micro particles. This leads to a material with magnetically controllable mechanical properties of which the magnetorheological effect is the best known. The addition of electroconductive particles to the polymer mix adds electrical properties to the material behaviour. The resulting electrical resistance of the sample can be manipulated by external magnetic fields and mechanical loads. This results in a distinct interplay of mechanical, electrical and magnetic effects with a highly complex time behaviour. In this paper a mechanical characterisation on multiple time scales was conducted to get an insight on the short and long-term electrical and mechanical behaviour of this novel material. The results show a complex resistivity behaviour on several timescales, sensitive to magnetic fields and strain velocity. The observed material exhibits fatigue and relaxation behaviour, whereas the magnetorheological effect appears not to interfere with the piezoresistive properties.

Clinical Application of Diode Laser (980 nm) in Maxillofacial Surgical Procedures.

Science.gov (United States)

Aldelaimi, Tahrir N; Khalil, Afrah A

2015-06-01

For many procedures, lasers are now becoming the treatment of choice by both clinicians and patients, and in some cases, the standard of care. This clinical study was carried out at Department of Maxillofacial Surgery, Ramadi Teaching Hospital, Rashid Private Hospital and Razi Private Hospital, Anbar Health Directorate, Anbar Province, Iraq. A total of 32 patients including 22 (≈ 70%) male and 10 (≈ 30%) female with age range from 5 months to 34 years old. Chirolas 20 W diode laser emitting at 980 nm was used. Our preliminary clinical findings include sufficient hemostasis, coagulation properties, precise incision margin, lack of swelling, bleeding, pain, scar tissue formation and overall satisfaction were observed in the clinical application. The clinical application of the diode (980 nm) laser in maxillofacial surgery proved to be of beneficial effect for daily practice and considered practical, effective, easy to used, offers a safe, acceptable, and impressive alternative for conventional surgical techniques.

Diffraction from relief gratings on a biomimetic elastomer cast

International Nuclear Information System (INIS)

Guerrero, Raphael A.; Aranas, Erika B.

2010-01-01

Biomimetic optical elements combine the optimized designs of nature with the versatility of materials engineering. We employ a beetle carapace as the template for fabricating relief gratings on an elastomer substrate. Biological surface features are successfully replicated by a direct casting procedure. Far-field diffraction effects are discussed in terms of the Fraunhofer approximation in Fourier space.

Maxillofacial trauma due to road traffic accidents in Benin City ...

African Journals Online (AJOL)

Distribution of maxillofacial bone and soft tissue injuries by vehicle type as well as associated injuries were documented. Results: The minibus was the vehicle type most often involved (36.2%) and tyre blowout (21.2%) was identified as the most common contributory factor. Males 117 (37.5%) in the 21 – 30 year- age range ...

C-arm fluoroscopy: a reliable modality for retrieval of foreign bodies in the maxillofacial region.

Science.gov (United States)

Pandyan, Deepak; Nandakumar, N; Qayyumi, Burhanuddin N; Kumar, Santosh

2013-11-01

The anatomic complexity of the maxillofacial region makes the retrieval of foreign bodies a daunting task for the maxillofacial Surgeon. Moreover the inability of 2-dimensional imaging to precisely locate foreign bodies makes it challenging. The anatomic proximity of critical structures and esthetic considerations limits the access and thus poses a greater challenge for the surgeon in cases of foreign body retrieval. Hereby we propose a simple technique and a case report to support, the retrieval of small (mobile C arm Fluoroscopy and a needle triangulation method to precisely locate a loosened miniplate screw in the mandibular angle region.

[Orthognathic surgery, master-piece of maxillo-facial surgery].

Science.gov (United States)

Reychler, H

2001-01-01

Orthognathic surgery is this field of the maxillofacial surgery which aims to reposition the jaws or some segments of these jaws when masticatory dysfunctions are evident. This tridimensional repositioning in the craniofacial skeleton allows to restore the masticatory function by means of osteotomies, which must be followed either by preoperative simulated bony displacements or by callus bone distraction. Not only are the functional benefits evident on the dental, articular and neuromuscular levels, but also a facial esthetic harmony can almost be obtained.

Polydopamine-Coated Main-Chain Liquid Crystal Elastomer as Optically Driven Artificial Muscle.

Science.gov (United States)

Tian, Hongmiao; Wang, Zhijian; Chen, Yilong; Shao, Jinyou; Gao, Tong; Cai, Shengqiang

2018-03-07

Optically driven active materials have received much attention because their deformation and motion can be controlled remotely, instantly, and precisely in a contactless way. In this study, we investigated an optically actuated elastomer with rapid response: polydopamine (PDA)-coated liquid crystal elastomer (LCE). Because of the photothermal effect of PDA coating and thermal responsiveness of LCE, the elastomer film contracted significantly with near-infrared (NIR) irradiation. With a fixed strain, light-induced actuating stress in the film could be as large as 1.5 MPa, significantly higher than the maximum stress generated by most mammalian skeletal muscle (0.35 MPa). The PDA-coated LCE films could also bend or roll up by surface scanning of an NIR laser. The response time of the film to light exposure could be as short as 1/10 of a second, comparable to or even faster than that of mammalian skeletal muscle. Using the PDA-coated LCE film, we designed and fabricated a prototype of robotic swimmer that was able to swim near the water-air interface by performing "swimming strokes" through reversible bending and unbending motions induced and controlled by an NIR laser. The results presented in this study clearly demonstrated that PDA-coated LCE is a promising optically driven artificial muscle, which may have great potential for applications of soft robotics and optomechanical coupling devices.

Fracture of elastomers by cavitation

KAUST Repository

Hamdi, Adel

2014-01-01

Cavitation phenomenon is studied in rubber-like materials by combining experimental, theoretical and numerical approaches. Specific tests are carried out on a Styrene Butadiene Rubber to point out main characteristics of cavitation phenomenon. Hydrostatic depression is numerically modelled using finite element method. Numerical results are compared to Ball\\'s and Hou & Abeyaratne\\'s models with regard to cavity nucleation in the material. Both models well fit experimental observations suggesting that the cavitation nucleation in elastomers depends on the confinement degree of the specimen. Finally, critical hydrostatic pressure and critical global deformation are proved to govern cavitation nucleation in the studied material. Critical loadings are identified by comparing experimental and numerical load-displacement curves. © 2013 Elsevier Ltd.

Computed tomography in the diagnosis of fractures of the maxillofacial area

International Nuclear Information System (INIS)

Angelova, I.; Yordanov, G.; Sirakov, V.; Velkova, K.

2013-01-01

Computed tomography (CT) is the current method of study in maxillofacial region, which produces cross-sectional images of a specific area. There are still questions about methodology and radiation exposure. The aim of the present study is to evaluate the CT in diagnosis of fractures in maxillofacial region. 42 patients with traumatic injuries to the facial skeleton are examined. Fractures of maxilla are occurring in 14.6 % of patients with traumatic diseases. Fractures of maxilla and zygomatic bone are found in 29.3 percent of the traumatic event. Isolated nasal bone fracture is observed in 2.4% of ail fractures. Compound fractures constitute 17.1% of the tested fractures. This group of patients are positioned at second place in frequency. Mandibular fractures ranked first in frequency -36.6% of all traumatic lesions. The methods include: 1. Slice computed tomography in the axial and coronary projection 2. Spiral CT in axial projection and coronary one. 3. Cone Beam Computed Tomography. CT diagnosis is based on an analysis of all the images. It must comply with the data from other studies. When analyzing the results we found that the percentage of patients with primary diagnosis of fractured upper jaw is 11 %, while CT diagnosis of this percentage increases to 16%. The percentage of patients with primary diagnosis fracture of mandibula and CT diagnosis is almost identical. In the present study, 3D and CT have similar results in the detection of fractures. Three-dimensional images dearly show the spatial anatomy of the face, the presence of fragments, as well as monitoring of fracture lines. Key words; Fractures. Maxillofacial Area. CT

Evaluation of time-accelerated irradiation method of elastomer by modulus-ultimate elongation profile

International Nuclear Information System (INIS)

Ito, Masayuki; Oka, Toshitaka; Hama, Yosimasa

2009-01-01

'Generalized modulus-ultimate elongation profile' was induced from the relationship between the modulus and the ultimate elongation of an elastomer that was quantitatively added crosslinking and scission. This profile can be used to evaluate the time-accelerated irradiation methods of ethylene-propylene-diene elastomer. The irradiation under low dose rate (0.33 kGy/h) at room temperature was the reference condition. The short-time irradiation condition was 4.2 kGy/h in 0.5 MPa oxygen at room temperature and 5.0 kGy/h in air at 70 o C. The former tended to bring about the higher ratio of scission than the reference condition; the latter tended to bring about the higher ratio of crosslinking.

Our Treatment Approaches in Severe Maxillofacial Injuries Occurring After Failed Suicide Attempts Using Long-Barreled Guns.

Science.gov (United States)

Kucuker, Ismail; Şimşek, Tekin; Keles, Musa Kemal; Yosma, Engin; Aksakal, Ibrahim Alper; Demir, Ahmet

2016-03-01

Maxillofacial traumas with long-barreled guns may sometimes cause catastrophic results by means of smashing in facial structures. In these patients, reconstruction strategies of both fragmented/lost soft and hard tissues still remain controversial. In their clinic, the authors treated 5 patients with severely injured face after failed suicide attempt between 2008 and 2013. In this study, the authors aimed to present their clinical experiences on these severely injured maxillofacial gunshot traumas and offer a treatment algorithm to gain a result as possible as satisfactory in terms of functionality and appearance.

Palm oil biodiesel synthesized with potassium loaded calcined hydrotalcite and effect of biodiesel blend on elastomer properties

Energy Technology Data Exchange (ETDEWEB)

Trakarnpruk, Wimonrat; Porntangjitlikit, Suriya [Petrochemistry and Polymer Science, Department of Chemistry, Faculty of Science, Chulalongkorn University, Bangkok 10330 (Thailand)

2008-07-15

Biodiesel was prepared from palm oil by transesterification with methanol in the presence of 1.5%K loaded-calcined Mg-Al hydrotalcite. Fatty acid methyl esters content of 96.9% and methyl ester yield of 86.6% were achieved using a 30:1 methanol to oil molar ratio at 100{sup o}C for 6 h and 7 wt% catalyst. The biodiesel was characterized and its impact on elastomer properties was evaluated. The compatibility of B10 diesel blend (10% biodiesel) with six types of elastomers commonly found in fuel systems (NBR, HNBR, NBR/PVC, acrylic rubber, co-polymer FKM, and terpolymer FKM) were investigated. The physical properties of elastomers after immersion in tested fuels (for 22, 670, and 1008 h at 100{sup o}C) were measured according to American Society of Testing and Materials (ASTM). These include swelling (mass change and volume change), hardness, tensile and elongation, as well as the dynamic mechanical property. The results showed that properties of NBR, NBR/PVC and acrylic rubber were affected more than other elastomers. This is due to the absorption and dissolving of biodiesel by rubber in these samples. Co-polymer FKM and terpolymer FKM which are fluoroelastomers show little property change. (author)

Effects of thermo-order-mechanical coupling on band structures in liquid crystal nematic elastomer porous phononic crystals.

Science.gov (United States)

Yang, Shuai; Liu, Ying

2018-08-01

Liquid crystal nematic elastomers are one kind of smart anisotropic and viscoelastic solids simultaneously combing the properties of rubber and liquid crystals, which is thermal sensitivity. In this paper, the wave dispersion in a liquid crystal nematic elastomer porous phononic crystal subjected to an external thermal stimulus is theoretically investigated. Firstly, an energy function is proposed to determine thermo-induced deformation in NE periodic structures. Based on this function, thermo-induced band variation in liquid crystal nematic elastomer porous phononic crystals is investigated in detail. The results show that when liquid crystal elastomer changes from nematic state to isotropic state due to the variation of the temperature, the absolute band gaps at different bands are opened or closed. There exists a threshold temperature above which the absolute band gaps are opened or closed. Larger porosity benefits the opening of the absolute band gaps. The deviation of director from the structural symmetry axis is advantageous for the absolute band gap opening in nematic state whist constrains the absolute band gap opening in isotropic state. The combination effect of temperature and director orientation provides an added degree of freedom in the intelligent tuning of the absolute band gaps in phononic crystals. Copyright © 2018 Elsevier B.V. All rights reserved.

Skin-Inspired Hydrogel-Elastomer Composite with Application in a Moisture Permeable Prosthetic Limb Liner

Science.gov (United States)

Ruiz, Esteban

Recent advances in fields such as 3D printing, and biomaterials, have enabled the development of a moisture permeable prosthetic liner. This project demonstrates the feasibility of the invention by addressing the three primary areas of risk including the mechanical strength, the permeability, and the ability to manufacture. The key enabling technology which allows the liner to operate is the skin inspired hydrogel elastomer composite. The skin inspiration is reflected in the molecular arrangement of the double network of polymers which mimics collagen-elastin toughening in the natural epidermis. A custom formulation for a novel tough double network nanocomposite reinforced hydrogel was developed to improve manufacturability of the liner. The liner features this double network nanocomposite reinforced hydrogel as a permeable membrane which is reinforced on either side by perforated silicone layers manufactured by 3d printing assisted casting. Uniaxial compression tests were conducted on the individual hydrogels, as well as a representative sample of off the shelf prosthetic liners for comparison. Permeability testing was also done on the same set of materials and compared to literature values for traditional hydrogels. This work led to the manufacture of three generations of liner prototypes, with the second and third liner prototype being tested with human participants.

Maxillofacial extramedullary hematopoiesis in a child with sickle cell presenting as bilateral periorbital cellulitis.

Science.gov (United States)

Reiersen, David A; Mandava, Mamatha; Jeroudi, Majed; Gungor, Anil

2014-07-01

Review of a case of paraosseous extramedullary hematopoiesis (EMH) affecting the maxillary sinuses and retro-orbital spaces imitating bilateral orbital cellulitis. Maxillofacial EMH causes diagnostic/therapeutic challenges. This case report describes a 4-year-old African American male with sickle cell disease (HbSS) who presented with bilateral orbitofacial swelling. Diagnosis was made with imaging and confirmed with tissue sampling. Partial exchange transfusion was utilized to stop the progression of maxillofacial EMH and to treat the patient's chronic anemia. Follow-up MRI showed regression of orbital and retro-orbital involvement. Early treatment with conservative modalities and close observation may prevent need for more invasive treatments. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

[Guided maxillofacial surgery: Simulation and surgery aided by stereolithographic guides and custom-made miniplates.

Science.gov (United States)

Philippe, B

2013-08-05

We present a new model of guided surgery, exclusively using computer assistance, from the preoperative planning of osteotomies to the actual surgery with the aid of stereolithographic cutting guides and osteosynthetic miniplates designed and made preoperatively, using custom-made titanium miniplates thanks to direct metal laser sintering. We describe the principles that guide the designing and industrial manufacturing of this new type of osteosynthesis miniplates. The surgical procedure is described step-by-step using several representative cases of dento-maxillofacial dysmorphosis. The encouraging short-term results demonstrate the wide range of application of this new technology for cranio-maxillofacial surgery, whatever the type of osteotomy performed, and for plastic reconstructive surgery. Copyright © 2013. Published by Elsevier Masson SAS.

Tough Self-Healing Elastomers by Molecular Enforced Integration of Covalent and Reversible Networks.

Science.gov (United States)

Wu, Jinrong; Cai, Li-Heng; Weitz, David A

2017-10-01

Self-healing polymers crosslinked by solely reversible bonds are intrinsically weaker than common covalently crosslinked networks. Introducing covalent crosslinks into a reversible network would improve mechanical strength. It is challenging, however, to apply this concept to "dry" elastomers, largely because reversible crosslinks such as hydrogen bonds are often polar motifs, whereas covalent crosslinks are nonpolar motifs. These two types of bonds are intrinsically immiscible without cosolvents. Here, we design and fabricate a hybrid polymer network by crosslinking randomly branched polymers carrying motifs that can form both reversible hydrogen bonds and permanent covalent crosslinks. The randomly branched polymer links such two types of bonds and forces them to mix on the molecular level without cosolvents. This enables a hybrid "dry" elastomer that is very tough with fracture energy 13500 Jm -2 comparable to that of natural rubber. Moreover, the elastomer can self-heal at room temperature with a recovered tensile strength 4 MPa, which is 30% of its original value, yet comparable to the pristine strength of existing self-healing polymers. The concept of forcing covalent and reversible bonds to mix at molecular scale to create a homogenous network is quite general and should enable development of tough, self-healing polymers of practical usage. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Airway management in patients with maxillofacial trauma - A retrospective study of 177 cases

Directory of Open Access Journals (Sweden)

Chetan B Raval

2011-01-01

Full Text Available Background: Airway management in maxillofacial injuries presents with a unique set of problems. Compromised airway is still a challenge to the anesthesiologist in spite of all modalities available. Maxillofacial injuries are the result of high-velocity trauma arising from road traffic accidents, sport injuries, falls and gunshot wounds. Any flaw in airway management may lead to grave morbidity and mortality in prehospital or hospital settings and as well as for reconstruction of fractures subsequently. Methods: One hundred and seventy-seven patients of maxillofacial injuries, operated over a period of one and half years during July 2008 to December 2009 in Al-Nahdha hospital were reviewed. All patients were reviewed in depth with age related type of injury, etiology and techniques of difficult airway management. Results: The major etiology of injuries were road traffic accidents (67% followed by sport (15% and fall (15%. Majority of patients were young in the age group of 11-30 years (71 %. Fracture mandible (53% was the most common injury, followed by fracture maxilla (21%, fracture zygoma (19% and pan-facial fractures (6%. Maxillofacial injuries compromise mask ventilation and difficult airway due to facial fractures, tissue edema and deranged anatomy. Shared airway with the surgeon needs special attention due to restrictions imposed during surgery. Several methods available for securing the airway, both decision-making and performance, are important in such circumstances. Airway secured by nasal intubation with direct visualization of vocal cords was the most common (57%, followed by oral intubation (17%. Other methods like tracheostomy and blind nasal intubation was avoided by fiberoptic bronchoscopic nasal intubation in 26% of patients. Conclusion: The results of this study indicated that surgically securing the airway by tracheostomy should be revised compared to other available methods. In the era of rigid fixation of fractures and the

Effect of carbon nanotube reinforcement on the properties of the recycled poly(ethylene terephthalate)/poly(ethylene naphthalate) (r-PET/PEN) blends containing functional elastomers

International Nuclear Information System (INIS)

Yesil, Sertan

2013-01-01

Highlights: • Mechanical properties of r-PET improved with addition of PEN, elastomers and CNT. • Elastomer size and dispersion played important role in the variation of properties. • Selective localization of CNT affected the mechanical and electrical properties. • E-EA-MAH based samples had higher mechanical properties than E-MA-GMA based ones. - Abstract: In this study, the mechanical, thermomechanical, thermal, electrical properties and the morphology of the composites, based on blends of recycled poly(ethylene terephthalate) (r-PET) and poly(ethylene naphthalate) (PEN) that were mixed with functional elastomers and multi walled carbon nanotube (CNT) were investigated. Two types of functional elastomers; terpolymer of ethylene–ethyl acrylate–maleic anhydride (E-EA-MAH) and terpolymer of ethylene–methyl acrylate–glycidyl methacrylate (E-MA-GMA), were used to ensure the miscibility between PET and PEN during the preparation of the blends and composites. All composite and blend samples were extruded by using a laboratory scale twin screw microcompounder. Test samples were prepared via laboratory scale injection molding machine. According to the results of the thermomechanical tests, usage of both elastomers enhanced the miscibility between r-PET and PEN. Morphological analyses showed that the blends and composites which contain E-EA-MAH exhibited better elastomer phase dispersion with smaller domain sizes when compared with the samples with E-MA-GMA. Samples prepared with E-EA-MAH had better mechanical properties than the ones containing E-MA-GMA due to the better elastomer phase dispersion. Moreover, addition of CNT also improved the mechanical properties of the samples for both elastomer types. In contrast to mechanical test results, samples prepared with E-MA-GMA had higher electrical conductivity values when compared with those of the ones containing E-EA-MAH due to the differences in the selective distribution of CNT particles between the

Surgeon Reimbursements in Maxillofacial Trauma Surgery: Effect of the Affordable Care Act in Ohio.

Science.gov (United States)

Khansa, Ibrahim; Khansa, Lara; Pearson, Gregory D

2016-02-01

Surgical treatment of maxillofacial injuries has historically been associated with low reimbursements, mainly because of the high proportion of uninsured patients. The Affordable Care Act, implemented in January of 2014, aimed to reduce the number of uninsured. If the Affordable Care Act achieves this goal, surgeons may benefit from improved reimbursement rates. The authors' purpose was to evaluate the effects of the Affordable Care Act on payor distribution and surgeon reimbursements for maxillofacial trauma surgery at their institution. A review of all patients undergoing surgery for maxillofacial trauma between January of 2012 and December of 2014 was conducted. Insurance status, and amounts billed and collected by the surgeon, were recorded. Patients treated before implementation of the Affordable Care Act were compared to those treated after. Five hundred twenty-three patients were analyzed. Three hundred thirty-four underwent surgery before implementation of the Affordable Care Act, and 189 patients underwent surgery after. After implementation of the Affordable Care Act, the proportion of uninsured decreased (27.2 percent to 11.1 percent; p reimbursement rate increased from 14.3 percent to 19.8 percent (p reimbursement rate increased. These trends should be followed over a longer term to determine the full effect of the Affordable Care Act.

The Effect of Clay/Multiwall Carbon Nanotube Hybrid Fillers on the Properties of Elastomer Nanocomposites

Directory of Open Access Journals (Sweden)

Sung Ho Song

2018-01-01

Full Text Available The hybrid fillers of 1D multiwalled carbon nanotubes (MWNT and 2D montmorillonite (MMT have led to excellent physical and chemical properties in high performance elastomer nanocomposites. In this study, the hybridization of PDDA (polydiallyldimethylammonium chloride functionalized MWNT (P-MWNT and hydroxyl-functionalized MMT (H-MMT was prepared by the electrostatic interaction between the positive charge on the MWNT and the negative charge on the MMT using a simple solution mixing process. Also, a styrene-butadiene rubber (SBR nanocomposite containing the hybrid nanofillers was prepared to improve the dispersion of nanofillers with SBR latex. The SBR nanocomposites with the hybrid nanofillers exhibited outstanding mechanical properties including modulus, tensile strength, and elongation at break, due to the enhanced interfacial bonding with the elastomer matrix. Furthermore, the hybrid nanofillers in the SBR matrix showed superior thermal and electrical properties and gas barrier performance at low loadings. The synergistic effects of the SBR produced by the hybridized nanofillers will open up new opportunities for elastomer composites with high performance.

A retrospective study of children and adolescents oral and maxillofacial lesions over a 20-year period in Kerman, Iran

Directory of Open Access Journals (Sweden)

Molook Torabi-Parizi

2017-08-01

Full Text Available BACKGROUND AND AIM: Oral and maxillofacial lesions vary in different geographic regions based on their clinical features. Until now, few investigations have studied these lesions in children and adolescents in Iran. The aim of this research was to study the clinicopathological manifestations of biopsied oral and maxillofacial lesions among children and adolescents in the south of Iran. METHODS: In this retrospective cross-sectional study, all the cases referred to the Department of Pathology, Kerman faculty of Dentistry, and two treatment centers of Kerman University of Medical Sciences, Kerman, Iran during 1996-2015 were included. All demographic information including age, gender, anatomic location and histopathologic diagnosis of the oral and maxillofacial biopsies in patients under 18 years was extracted from patients’ chart fields. SPSS was used for the data analysis. RESULTS: Of 3196 oral and maxillofacial lesions, 326 cases (10.2% occurred in the age group under 18 years. The most common group was inflammatory/reactive lesions (36.8%. The most common lesions were pyogenic granuloma (9.20%, peripheral giant cell granuloma (8.89%, and dentigerous cyst (8.28%. Gingiva was the main involved area and the female to male ratio was 1.1 to 1. CONCLUSION: Our study revealed that almost 10.2% of oral and maxillofacial lesions occurred in children and adolescents. The majority of lesions were benign, and malignant lesions were rarely observed in the sample. The most prevalent biopsied lesions were inflammatory/reactive lesions. Unlike other studies, lower rates of mucocele were observed in this study. These findings can improve patient’s management among dentists and surgeons.

Do Quantitative Measures of Research Productivity Correlate with Academic Rank in Oral and Maxillofacial Surgery?

Science.gov (United States)

Susarla, Srinivas M; Dodson, Thomas B; Lopez, Joseph; Swanson, Edward W; Calotta, Nicholas; Peacock, Zachary S

2015-08-01

Academic promotion is linked to research productivity. The purpose of this study was to assess the correlation between quantitative measures of academic productivity and academic rank among academic oral and maxillofacial surgeons. This was a cross-sectional study of full-time academic oral and maxillofacial surgeons in the United States. The predictor variables were categorized as demographic (gender, medical degree, research doctorate, other advanced degree) and quantitative measures of academic productivity (total number of publications, total number of citations, maximum number of citations for a single article, I-10 index [number of publications with ≥ 10 citations], and h-index [number of publications h with ≥ h citations each]). The outcome variable was current academic rank (instructor, assistant professor, associate professor, professor, or endowed professor). Descriptive, bivariate, and multiple regression statistics were computed to evaluate associations between the predictors and academic rank. Receiver-operator characteristic curves were computed to identify thresholds for academic promotion. The sample consisted of 324 academic oral and maxillofacial surgeons, of whom 11.7% were female, 40% had medical degrees, and 8% had research doctorates. The h-index was the most strongly correlated with academic rank (ρ = 0.62, p research activity.

Review of Maxillofacial Hardware Complications and Indications for Salvage

OpenAIRE

Hernandez Rosa, Jonatan; Villanueva, Nathaniel L.; Sanati-Mehrizy, Paymon; Factor, Stephanie H.; Taub, Peter J.

2015-01-01

From 2002 to 2006, more than 117,000 facial fractures were recorded in the U.S. National Trauma Database. These fractures are commonly treated with open reduction and internal fixation. While in place, the hardware facilitates successful bony union. However, when postoperative complications occur, the plates may require removal before bony union. Indications for salvage versus removal of the maxillofacial hardware are not well defined. A literature review was performed to identify instances w...

The role of diagnostic ultrasound as a new diagnostic aid in oral and maxillofacial surgery

Directory of Open Access Journals (Sweden)

Siva Subramaniyam Venkataraman

2012-01-01

Full Text Available Only very few studies have been done in the past to evaluate the usefulness and limitations of ultrasonography in oral and maxillofacial surgery. This study, though in an embryonic stage, has been done to bring this technique to limelight and to put forth the importance of its use and limitations in the branch of oral surgery. The purpose of this study was to investigate and study the characteristic pattern of the oral tissues on gray scale ultrasonography and to assess the practical applicability of this new diagnostic technique in diagnosing various tissue pathologies in the field of oral and maxillofacial surgery.

Head and Maxillofacial Injuries in Child and Adolescent Victims of Automotive Accidents

Directory of Open Access Journals (Sweden)

Alessandro Leite Cavalcanti

2014-01-01

Full Text Available Background. Victims of motor vehicle accidents may suffer multiple lesions, including maxillofacial injuries. The aim of this study was to evaluate the prevalence and factors associated with head, facial, and maxillofacial injuries in child and adolescent victims of automobile accidents. A cross-sectional study was carried out with analysis of forensic medical reports from the Legal Medical Institute of Campina Grande, Brazil, between January 2008 and December 2011. Descriptive and inferential statistical analysis was conducted using the chi-square test (α = 0.05. From 1613 medical reports analyzed, the sample is composed 232 (14.4% reports referring to child and adolescent victims of automobile accidents aged 0–19 years of both sexes. Victims were mostly adolescents aged from 15 to 19 years (64.2%, males (73.7%, and motorcyclists (51.3%. More than half of the victims had single lesions (54.3% located in the head (20.7% and face (21.6%. Head injuries occurred more frequently in children aged 0–4 years (53.8%, PR = 5.065, 95% CI = 1.617–5.870 and pedestrians (30.4%, PR = 2.039, 95% CI = 1.024–4.061, while facial and maxillofacial injuries occurred in higher proportion among females (31.1%, PR = 0.489, 95% CI = 0.251–0.954. Our findings suggest that accidents involving motorcyclists are the most prevalent, affecting male adolescents aged from 15 to 19 years, resulting in a high frequency of injuries in the head and face regions.

Curriculum Planning for Oral and Maxillofacial Surgery Assistant Program. Final Report.

Science.gov (United States)

Taylor, Mary Ann

This project was conducted to develop a curriculum for dental auxiliary training in the dental specialty field of oral and maxillofacial surgery. Research was conducted to identify the major functions performed by an oral surgery assistant and then to organize these functions into an educational program that would provide adequate didactic and…

Airway Management in Maxillofacial Trauma: A Retrospective Review of 127 Cases

Directory of Open Access Journals (Sweden)

V Saraswat

2008-01-01

Maxillofacial injuries need special attention since it involves difficult airway due to fracture to facial bones, Further the airway is shared with surgeon and restrictions are imposed during surgery. Issues involved are time of surgery, preoperative airway assessment, type of intubation and way to achieve it, alternative methods available and their complications.

Spark erosion implant prosthetics in the management of an acquired maxillofacial defect.

Science.gov (United States)

Bloem, T J; Baxter, W D; Vivas, J

1996-03-01

The concept and use of spark erosion (EDM) prosthetics in implant prosthodontics has been described and demonstrated in its application to a patient suffering maxillofacial trauma. The advantages and disadvantages of this technology have been discussed for the edification of the restorative and surgical provider.

Numerical study of liquid crystal elastomers by a mixed finite element method

KAUST Repository

LUO, C.; CALDERER, M. C.

2011-01-01

Liquid crystal elastomers present features not found in ordinary elastic materials, such as semi-soft elasticity and the related stripe domain phenomenon. In this paper, the two-dimensional Bladon-Terentjev-Warner model and the one-constant Oseen

Batch fabrication of optical actuators using nanotube–elastomer composites towards refreshable Braille displays

International Nuclear Information System (INIS)

Camargo, C J; Campanella, H; Torras, N; Zinoviev, K; Esteve, J; Marshall, J E; Terentjev, E M

2012-01-01

This paper reports an opto-actuable device fabricated using micro-machined silicon moulds. The actuating component of the device is made from a composite material containing carbon nanotubes (CNTs) embedded in a liquid crystal elastomer (LCE) matrix. We demonstrate the fabrication of a patterned LCE-CNT film by a combination of mechanical stretching and thermal cross-linking. The resulting poly-domain LCE-CNT film contains ‘blister-shaped’ mono-domain regions, which reversibly change their shape under light irradiation and hence can be used as dynamic Braille dots. We demonstrate that blisters with diameters of 1.0 and 1.5 mm, and wall thickness 300 µm, will mechanically contract under irradiation by a laser diode with optical power up to 60 mW. The magnitude of this contraction was up to 40 µm, which is more than 10% of their height in the ‘rest’ state. The stabilization time of the material is less than 6 s for both actuation and recovery. We also carried out preliminary tests on the repeatability of this photo-actuation process, observing no material or performance degradation. This manufacturing approach establishes a starting point for the design and fabrication of wide-area tactile actuators, which are promising candidates for the development of new Braille reading applications for the visually impaired. (paper)

Rare etiological factor of maxillofacial injury: Case series seen and managed in a tertiary referral centre

Directory of Open Access Journals (Sweden)

Ramat Oyebunmi Braimah

2016-01-01

Full Text Available Entanglement injury from local milling/grinding machine with a conveyor belt is a rare etiology of maxillofacial injuries. While there is abundant literature on industrial cause of trauma, entanglement injury as a mechanism has not been reported in the literature. We present two cases of maxillofacial injury secondary to entanglement of the loose apparel into the conveyor belt of the local grinding machine. The community should be aware of this rare cause of trauma, and adequate protection of children using these facilities should be enforced. One of such measure is to provide physical barriers to guard against these machines.

Study of mechanical and thermal properties of soy flour elastomers

Science.gov (United States)

Allen, Kendra Alicia

Bio-based plastics are becoming viable alternatives to petroleum-based plastics because they decrease dependence on petroleum derivatives and are more environmentally friendly. Raw materials such as soy flour are widely available, low cost, lightweight, stiffness and have high strength characteristics, but weak interfacial adhesion between the soy flour and the polymer poses a challenge. In this study, soy flour was utilized as a filler in thermoplastic elastomer composites. A surface modification called acetylation was investigated at soy flour concentrations of 10 wt%, 15 wt% and 20 wt%. The mechanical properties of the composites were then compared to that of elastomers without a filler. Chemical characterization of the acetylated soy flour was attempted in order to understand what occurs during the reaction and after completion. In the range of tests, soy flour loadings were observed to be inversely proportional to tensile strength for both the untreated and treated soy flour. However, the acetylated soy flour at 10 wt% concentration performed comparable to that of the neat rubber and resulted in an increase in tensile strength. Unexpectedly, the acetylation reaction increased elongation, which reduced stress within the composite and is believed to increase the adhesion of the soy flour to that of the elastomer. In the nuclear magnetic resonance (SS-NMR), the intensity for the treated soy flour was larger than that of the untreated soy flour for the acetyl groups that were attached to the soy flour, particularly, the carbonyl function group next to the deprotonated oxygen and the methyl group next to the carbonyl. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) indicated that the acetylated soy flour is slightly more thermally stable than the untreated soy flour. The treated soy flour also increased the decomposition temperature of the composite.

Accuracy of clinical coding for procedures in oral and maxillofacial surgery.

Science.gov (United States)

Khurram, S A; Warner, C; Henry, A M; Kumar, A; Mohammed-Ali, R I

2016-10-01

Clinical coding has important financial implications, and discrepancies in the assigned codes can directly affect the funding of a department and hospital. Over the last few years, numerous oversights have been noticed in the coding of oral and maxillofacial (OMF) procedures. To establish the accuracy and completeness of coding, we retrospectively analysed the records of patients during two time periods: March to May 2009 (324 patients), and January to March 2014 (200 patients). Two investigators independently collected and analysed the data to ensure accuracy and remove bias. A large proportion of operations were not assigned all the relevant codes, and only 32% - 33% were correct in both cycles. To our knowledge, this is the first reported audit of clinical coding in OMFS, and it highlights serious shortcomings that have substantial financial implications. Better input by the surgical team and improved communication between the surgical and coding departments will improve accuracy. Copyright © 2016 The British Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Large amplitude oscillatory measurements as mechanical characterization methods for soft elastomers

DEFF Research Database (Denmark)

Skov, Anne Ladegaard

2012-01-01

oscillating elongation (LAOE)1 and planar elongation2, 3 make the ideal set of experiments to evaluate the mechanical performance of DEAPs. We evaluate the mechanical performance of several soft elastomers applicable for DEAP purposes such as poly(propyleneoxide) (PPO) networks3, 4 and traditional unfilled...

New elastomeric silicone based networks applicable as electroactive systems

DEFF Research Database (Denmark)

Bejenariu, Anca Gabriela; Boll, Mads; Lotz, Mikkel Rønne

2011-01-01

. In this study we focus on optimization of the mechanical properties of the elastomer and show that it is possible to lower the elastic modulus and still not compromise the other required mechanical properties such as fast response, stability, low degree of viscous dissipation and high extensibility....... The elastomers are prepared from a vinyl-terminated polydimethyl siloxane (PDMS) and a 4-functional crosslinker by a platinum-catalyzed hydrosilylation reaction between the two reactants. Traditionally, elastomers based on hydrosilylation are prepared via a ‘one-step two-pot’ procedure (with a mix A and a mix B...

EXPERIMENTAL INVESTIGATION OF THE ADHESIVE CONTACT WITH ELASTOMERS: EFFECT OF SURFACE ROUGHNESS

Directory of Open Access Journals (Sweden)

Lars Voll

2015-04-01

Full Text Available Adhesion between an elastomer and a steel indenter was studied experimentally and described with an analytical model. Cylindrical indenters having different roughness were brought into contact with an elastomer with various normal forces. After a “holding time”, the indenter was pulled with a constant velocity, which was the same in all experiments. We have studied the regime of relatively small initial normal loadings, large holding times and relatively large pulling velocities, so that the adhesive force did not depend on the holding time but did depend on the initially applied normal force and was approximately proportional to the pulling velocity. Under these conditions, we found that the adhesive force is inversely proportional to the roughness and proportional to the normal force. For the theoretical analysis, we used a previously published MDR-based model.

Prevalence and patterns of combat sport related maxillofacial injuries

OpenAIRE

Shirani, Gholamreza; Kalantar Motamedi, Mohammad Hosein; Ashuri, Alireza; Eshkevari, Pooyan Sadr

2010-01-01

Aim: This study was designed to assess the prevalence, distribution, and patterns of injury among athletes engaged in combat sports and compare the prevalence, pattern, and types of oral and maxillofacial trauma in these athletes. Materials and Methods: A total of 120 male athletes engaged in four combat sports (boxing, taekwondo, kickboxing, and Muay Thai) who had sustained bodily trauma were studied; 95 subjects with at least one traumatic injury to the face requiring treatment were referre...

Basic studies of CT in the maxillofacial areas, 1

International Nuclear Information System (INIS)

Suzuki, Shinichiro; Kaneko, Hiroshi; Higashi, Tomomitsu; Takenaka, Eiichi.

1982-01-01

As CT values of hard tissues would pose problems in the application of CT to the maxillofacial area, attenuation coefficients of each oral hard tissue were examined based on the existing data, and the linearity in the area of high x-ray attenuation was examined. We thought that a new contrast scale suitable for each area should be established for measurements of CT values of tissues of high x-ray attenuation such as teeth. (Chiba, N.)

Flammability and Thermophysical Characterization of Thermoplastic Elastomer Nanocomposites

Science.gov (United States)

2004-08-01

State University – M. Namani • Southern Clay Products – D. Hunter • Applied Sciences Inc. – J. Glasglow • Omega Point Laboratories – S . Romo Financial...Characterization of Thermoplastic Elastomer Nanocomposites 5a. CONTRACT NUMBER F04611-99-C-0025 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR( S ... S ) AND ADDRESS(ES) ERC, Inc,AFRL/PRS,10 E. Saturn Blvd.,Edwards AFB,CA,93524 8. PERFORMING ORGANIZATION REPORT NUMBER E04-082 9. SPONSORING

Design and Preparation of Cross-Linked Polystyrene Nanoparticles for Elastomer Reinforcement

Directory of Open Access Journals (Sweden)

Ming Lu

2010-01-01

Full Text Available Cross-linked polystyrene (PS particles in a latex form were synthesized by free radical emulsion polymerization. The nano-PS-filled elastomer composites were prepared by the energy-saving latex compounding method. Results showed that the PS particles took a spherical shape in the size of 40–60 nm with a narrow size distribution, and the glass-transition temperature of the PS nanoparticles increased with the cross-linking density. The outcomes from the mechanical properties demonstrated that when filled into styrene-butadiene rubber (SBR, nitrile-butadiene rubber (NBR, and natural rubber (NR, the cross-linked PS nano-particles exhibited excellent reinforcing capabilities in all the three matrices, and the best in the SBR matrix. In comparison with that of the carbon black filled composites, another distinguished advantage of the cross-linked PS particles filled elastomer composites was found to be light weight in density, which could help to save tremendous amount of energy when put into end products.

A multicenter study of biopsied oral and maxillofacial lesions in a Brazilian pediatric population.

Science.gov (United States)

Silva, Leni Verônica de Oliveira; Arruda, José Alcides Almeida; Martelli, Stephanie Joana; Kato, Camila de Nazaré Alves de Oliveira; Nunes, Laiz Fernanda Mendes; Vasconcelos, Ana Carolina Uchoa; Tarquinio, Sandra Beatriz Chaves; Gomes, Ana Paula Neutzling; Gomez, Ricardo Santiago; Mesquita, Ricardo Alves; Silveira, Marcia Maria Fonseca da; Sobral, Ana Paula Veras

2018-03-15

The aim of this study was to investigate the prevalence of oral and maxillofacial lesions among children from representative regions of Brazil. A retrospective descriptive study was conducted. Biopsy records comprising the period from 2000 to 2015 were obtained from the archives of three Brazilian oral pathology referral centers. A total of 32,506 biopsy specimens were analyzed, and specimens from 1,706 children aged 0-12 years were selected. Gender, age, anatomical location and histopathological diagnosis were evaluated. Descriptive statistics was carried out. Likelihood ratio tests were used to evaluate the association between the categorical variables. The level of significance was set at 0.05. The post-hoc test was used to identify the subgroups that significantly differed from one another, and the Bonferroni correction was applied. A total of 1,706 oral and maxillofacial lesions were diagnosed in pediatric patients, including 51.9% girls. Oral mucocele was the most prevalent reactive/inflammatory lesion (64%). The most commonly affected sites were the lips (34.5%) and mandible (19.9%). A significant association was observed between age and the group of lesions of the oral cavity (p oral and maxillofacial lesions were frequent and showed wide diversity, with the prevalence of mucocele. Knowledge of oral lesions is important for pediatric dentists worldwide, since it provides accurate data for the diagnosis and oral health of children.

Simultaneous Detection of Displacement, Rotation Angle, and Contact Pressure Using Sandpaper Molded Elastomer Based Triple Electrode Sensor.

Science.gov (United States)

Choi, Eunsuk; Sul, Onejae; Lee, Seung-Beck

2017-09-06

In this article, we report on a flexible sensor based on a sandpaper molded elastomer that simultaneously detects planar displacement, rotation angle, and vertical contact pressure. When displacement, rotation, and contact pressure are applied, the contact area between the translating top elastomer electrode and the stationary three bottom electrodes change characteristically depending on the movement, making it possible to distinguish between them. The sandpaper molded undulating surface of the elastomer reduces friction at the contact allowing the sensor not to affect the movement during measurement. The sensor showed a 0.25 mm −1 displacement sensitivity with a ±33 μm accuracy, a 0.027 degree −1 of rotation sensitivity with ~0.95 degree accuracy, and a 4.96 kP −1 of pressure sensitivity. For possible application to joint movement detection, we demonstrated that our sensor effectively detected the up-and-down motion of a human forefinger and the bending and straightening motion of a human arm.

21 CFR 177.1050 - Acrylonitrile/styrene copoly-mer modified with butadiene/styrene elastomer.

Science.gov (United States)

2010-04-01

... parts by weight of a grafted rubber consisting of (i) 8-12 parts of butadiene/styrene elastomer... limitations are determined by an infrared spectro-photo-metric method titled “Infrared Spectro-photo-metric...

Phenomena of nonlinear oscillation and special resonance of a dielectric elastomer minimum energy structure rotary joint

Science.gov (United States)

Zhao, Jianwen; Niu, Junyang; McCoul, David; Ren, Zhi; Pei, Qibing

2015-03-01

The dielectric elastomer minimum energy structure can realize large angular deformations by a small voltage-induced strain of the dielectric elastomer, so it is a suitable candidate to make a rotary joint for a soft robot. Driven with an alternating electric field, the joint deformation vibrational frequency follows the input voltage frequency. However, the authors find that if the rotational inertia increases such that the inertial torque makes the frame deform over a negative angle, then the joint motion will become complicated and the vibrational mode will alter with the change of voltage frequency. The vibration with the largest amplitude does not occur while the voltage frequency is equal to natural response frequency of the joint. Rather, the vibrational amplitude will be quite large over a range of other frequencies at which the vibrational frequency is half of the voltage frequency. This phenomenon was analyzed by a comparison of the timing sequences between voltage and joint vibration. This vibrational mode with the largest amplitude can be applied to the generation lift in a flapping wing actuated by dielectric elastomers.

A retrospective study of oral and maxillofacial injuries in Seremban Hospital, Malaysia.

Science.gov (United States)

Ramli, Roszalina; Rahman, Normastura Abdul; Rahman, Roslan Abdul; Hussaini, Haizal Mohd; Hamid, Abdul Latif Abdul

2011-04-01

Aetiology of oral and maxillofacial injuries in this country includes motorvehicle accident (MVA), fall, industrial accidents and others. Among these causes, MVA accident is the predominant cause of injury in Malaysia. A retrospective record review was carried out using hospital records of all patients who sustained oral and maxillofacial injury at the Department of Oral Surgery, Seremban Hospital, Negeri Sembilan, Malaysia between 1998 and 2002. Information related to demographics, aetiology of trauma, vehicles involved in collision, location of injuries and treatment modalities were reviewed. Two thousand nine hundred and eighty-six patients sustained oral and maxillofacial injuries. Of these patients, 79.2% were men and the remaining were women. Among all the races, Malays had the highest involvement (50.6%) followed by Indians (24.5%), Chinese (19.6%) and others (5.3%). There were statistically significant results on the association of aetiology and the ethnic groups, in the age group of 30 years or less and male gender (P < 0.001). The most common injury was the soft-tissue injury followed by dental and dentoalveolar injuries and bony fracture. Among all facial fractures, 66.3% were managed conservatively, 13% were treated surgically and 19.7% did not have any intervention. In relation to dental and dentoalveolar injuries, 64.8% had treatment in the form of splinting, restorations or dental extraction. The rest of the patients (35.2%) were referred to their dentists or did not have any active treatment at Seremban Hospital. Most of the dental and facial injuries in Seremban Hospital were caused by MVA and were predominantly managed using conservative methods. © 2011 John Wiley & Sons A/S.

Survival in patients with oral and maxillofacial diffuse large B-cell lymphoma

Directory of Open Access Journals (Sweden)

Janet Ofelia Guevara-Canales

2013-11-01

Full Text Available The purpose of this study was to determine the survival and prognostic factors of patients with diffuse large B-cell lymphoma (DLBCL of the oral cavity and maxillofacial region. Retrospectively, the clinical records of patients with a primary diagnosis of DLBCL of the oral cavity and maxillofacial region treated at the A.C. Camargo Hospital for Cancer, São Paulo, Brazil, between January 1980 and December 2005 were evaluated to determine (A overall survival (OS at 2 and 5 years and the individual survival percentage for each possible prognostic factor by means of the actuarial technique (also known as mortality tables, and the Kaplan Meier product limit method (which provided the survival value curves for each possible prognostic factor; (B prognostic factors subject to univariate evaluation with the log-rank test (also known as Mantel-Cox, and multivariate analysis with Cox's regression model (all the variables together. The data were considered significant at p ≤ 0.05. From 1980 to 2005, 3513 new cases of lymphomas were treated, of which 151 (4.3% occurred in the oral cavity and maxillofacial region. Of these 151 lesions, 48 were diffuse large B-cell lymphoma, with 64% for OS at 2 years and 45% for OS at 5 years. Of the variables studied as possible prognostic factors, multivariate analysis found the following variables have statistically significant values: age (p = 0.042, clinical stage (p = 0.007 and performance status (p = 0.031. These data suggest that patients have a higher risk of mortality if they are older, at a later clinical stage, and have a higher performance status.

Analysis of the pattern of maxillofacial fractures in north western of Iran: A retrospective study

Directory of Open Access Journals (Sweden)

Mesgarzadeh Ali

2011-01-01

Full Text Available Background : Maxillofacial fractures can lead to substantial long-term functional, esthetic and psychological complications. Aim : The aim of this study is to evaluate these injuries in a Turkish Iranian population. Materials and Methods : A retrospective study of 170 patients with 210 maxillofacial fractures admitted to the emergency department of a central referral emergency hospital in the area over a 5 year period is presented. Patients′ data included demographic information, etiology, site and associated injuries and complications. Results : Road traffic accident was the commonest cause (40% and the age group of 21-30 comprised the biggest group (30%. Mandibular fractures outnumbered midface fractures (150vs.60. Ramus (21.5% and zygoma (26.5% were the commonest fracture regions respectively in mandible and midface. Male: female ratio was 3.8:1 Almost half of patients (46% had sustained associated injuries most of which was soft tissue laceration of the face (17.5%. 22 patient (13% had associated complication and the hemorrhage was the commonest form of that (9%. Conclusion : It seems that road traffic accidents continue to be the leading cause of maxillofacial fractures and there is an urgent need to implement enhanced regulations and monitoring on motor vehicular traffic.

Systematic Review of Pain assessment scales in newborns under maxillofacial surgery Admitted to the surgical ward

Directory of Open Access Journals (Sweden)

Shapour Yaripoor

2016-10-01

Full Text Available Having standard tools for measuring pain in infants is essential. The aim of this study is to review the scale of pain in newborns under maxillofacial surgery Admitted to the surgical ward. Integrative review study of articles published from 2000 to 2015, carried out in the following databases: Scopus, PubMed, CINAHL, LILACS, Cochrane, medscape and google scholar. The sample consisted of 17 articles. MeSH headings searched included pain measurement, pain scale, newborn pain, infant pain scale, maxillofacial surgery and pain perception. 16 neonatal pain assessment tools were found. Of the 232 original articles, 17 review articles in the field of pain assessment tools in infant under maxillofacial surgery who had inclusion criteria were selected. The most studied was the Premature Infant Pain Profile (PIPP, The CRIES and the Neonatal Infant Pain Scale (NIPS. Infant pain assessment is not universally standardized. Practitioners may assess pain; however, they may not consistently use the same criteria to do so. The use of Neonatal Facial Coding System, the Neonatal Infant Pain Scale and the Premature Infant Pain Profile Can accurately show the amount of pain in newborns.

High dielectric permittivity elastomers from well-dispersed expanded graphite in low concentrations

DEFF Research Database (Denmark)

Daugaard, Anders Egede; Hassouneh, Suzan Sager; Kostrzewska, Malgorzata

2013-01-01

The development of elastomer materials with a high dielectric permittivity has attracted increased interest over the last years due to their use in for example dielectric electroactive polymers. For this particular use, both the electrically insulating properties - as well as the mechanical...

Hydrolytic stability of polycarbonate-based polyurethane elastomers tested in physiologically simulated conditions

Czech Academy of Sciences Publication Activity Database

Serkis, Magdalena; Špírková, Milena; Poreba, Rafal; Hodan, Jiří; Kredatusová, Jana; Kubies, Dana

2015-01-01

Roč. 119, September (2015), s. 23-34 ISSN 0141-3910 R&D Projects: GA ČR(CZ) GA13-06700S Institutional support: RVO:61389013 Keywords : polyurethane * elastomer * hydrolytic stability Subject RIV: CD - Macromolecular Chemistry Impact factor: 3.120, year: 2015

Plasma polymerization surface modification of Carbon black and its effect in elastomers

NARCIS (Netherlands)

Mathew, T.; Datta, Rabin; Dierkes, Wilma K.; Talma, Auke; Ooij, W.J.; Noordermeer, Jacobus W.M.

2011-01-01

Surface modification of carbon black by plasma polymerization was aimed to reduce its surface energy in order to compatibilize the filler with various elastomers. A fullerenic carbon black was used for the modification process. Thermogravimetric analysis, wetting behavior with liquids of known

Coaxial Thermoplastic Elastomer-Wrapped Carbon Nanotube Fibers for Deformable and Wearable Strain Sensors

KAUST Repository

Zhou, Jian; Xu, Xuezhu; Xin, Yangyang; Lubineau, Gilles

2018-01-01

performances in these design requirements. Here, achieving highly stretchable and sensitive strain sensors by using a coaxial structure, prepared via coaxial wet spinning of thermoplastic elastomer-wrapped carbon nanotube fibers, is proposed. The sensors attain

Polypropylene/elastomers/organophilic bentonite nanocomposites. Influence of elastomer content on morphology and mechanical properties

International Nuclear Information System (INIS)

Ferreira, K.R.M.; Braga, C.R.C.; Andrade, D.L.A.C.S.; Carvalho, L.H.; Silva, S.M.L.

2010-01-01

In this study, the effect of the elastomer terpolymer ethylene-propylene-diene (EPDM) content on the morphology and mechanical properties of polypropylene PP/EPDM/organophilic bentonite nanocomposite was evaluated. The bentonite, supplied by Bentonit Uniao Nordeste, was purified and organically modified with cetyl trimethyl quaternary ammonium (cetremide) before the incorporation in PP/EPDM blend. The blends with various amounts of EPDM (10, 20, 30 and 40 wt%) and 1 phr of organoclay were prepared by melt-blending at 180 deg C and 50 rpm for 15 min with an internal mixer (Haake). The blends were characterized by X-ray diffraction and mechanical properties (tensile strength). According to the results, we concluded that the content of EPDM affected the morphology and mechanical properties of nanocomposites resulting in improvement in mechanical and morphological properties when a content of 30 wt% of EPDM was used. (author)

A novel variable stiffness mechanism for dielectric elastomer actuators

Science.gov (United States)

Li, Wen-Bo; Zhang, Wen-Ming; Zou, Hong-Xiang; Peng, Zhi-Ke; Meng, Guang

2017-08-01

In this paper, a novel variable stiffness mechanism is proposed for the design of a variable stiffness dielectric elastomer actuator (VSDEA) which combines a flexible strip with a DEA in a dielectric elastomer minimum energy structure. The DEA induces an analog tuning of the transverse curvature of the strip, thus conveniently providing a voltage-controllable flexural rigidity. The VSDEA tends to be a fully flexible and compact structure with the advantages of simplicity and fast response. Both experimental and theoretical investigations are carried out to reveal the variable stiffness performances of the VSDEA. The effect of the clamped location on the bending stiffness of the VSDEA is analyzed, and then effects of the lengths, the loading points and the applied voltages on the bending stiffness are experimentally investigated. An analytical model is developed to verify the availability of this variable stiffness mechanism, and the theoretical results demonstrate that the bending stiffness of the VSDEA decreases as the applied voltage increases, which agree well with the experimental data. Moreover, the experimental results show that the maximum change of the relative stiffness can reach about 88.80%. It can be useful for the design and optimization of active variable stiffness structures and DEAs for soft robots, vibration control, and morphing applications.

Portfolio: a comprehensive method of assessment for postgraduates in oral and maxillofacial surgery.

Science.gov (United States)

Kadagad, Poornima; Kotrashetti, S M

2013-03-01

Post graduate learning and assessment is an important responsibility of an academic oral and maxillofacial surgeon. The current method of assessment for post graduate training include formative evaluation in the form of seminars, case presentations, log books and infrequently conducted end of year theory exams. End of the course theory and practical examination is a summative evaluation which awards the degree to the student based on grades obtained. Oral and maxillofacial surgery is mainly a skill based specialty and deliberate practice enhances skill. But the traditional system of assessment of post graduates emphasizes their performance on the summative exam which fails to evaluate the integral picture of the student throughout the course. Emphasis on competency and holistic growth of the post graduate student during training in recent years has lead to research and evaluation of assessment methods to quantify students' progress during training. Portfolio method of assessment has been proposed as a potentially functional method for post graduate evaluation. It is defined as a collection of papers and other forms of evidence that learning has taken place. It allows the collation and integration of evidence on competence and performance from different sources to gain a comprehensive picture of everyday practice. The benefits of portfolio assessment in health professions education are twofold: it's potential to assess performance and its potential to assess outcomes, such as attitudes and professionalism that are difficult to assess using traditional instruments. This paper is an endeavor for the development of portfolio method of assessment for post graduate student in oral and maxillofacial surgery.

Freeze dried bone allografts in dental and maxillofacial reconstructive surgery - experience in Malaysia

International Nuclear Information System (INIS)

Abd Rani Samsudin; Meor Zaidi Meor Kamal

1999-01-01

The utilisation of vascularised and free bone autografts remain the goal standard in maxillofacial reconstructive surgery in Malaysia, but the use of freeze dried bone allograft is still widely practiced in many centres with variable results. This study evaluate the effectiveness and clinical efficacy of using radiation sterilised freeze dried bone allografts in oral and maxillofacial reconstructive surgery. The bone grafts were prepared at the Malaysian National Tissue Bank. Seventy eight patients who had undergone oral and Maxillofacial surgical procedures with reconstruction using bone allografts were included in this study. 50 patients were male and 28 patients were female and their age ranged from 14 to 75 years. Forty two patients underwent enucleation of benign cystic lesions in the jaws, 15 patients underwent repair of orbital floor fractures, 6 patients of jaw fractures with partial loss of bone while 8 patients underwent augmentation of depressed cheek bone. Another 4 patients had partial resection of the mandible because of cancer and 3 patients had facial osteotomies. A follow up period of 12 months up to 4 years was carried out. The patients were assessed both clinically and radiologically throughout their follow up visits. Clinical assessment showed no evidence of rejection of the implanted freeze dried allografts. Bone allografts implanted as inlay grafts demonstrated a better clinical performance than onlay grafts and the poorest results were obtained following bridging bony defects in the jaws. Radiation sterilised freeze dried bone allografts produced at the Malaysian National Tissue Bank are bio-compatible, functional, and provide predictable results when applied to selected areas of the facial skeleton

In Situ Polymorphic Alteration of Filler Structures for Biomimetic Mechanically Adaptive Elastomer Nanocomposites.

Science.gov (United States)

Natarajan, Tamil Selvan; Okamoto, Shigeru; Stöckelhuber, Klaus Werner; Wießner, Sven; Reuter, Uta; Fischer, Dieter; Ghosh, Anik Kumar; Heinrich, Gert; Das, Amit

2018-04-30

A mechanically adaptable elastomer composite is prepared with reversible soft-stiff properties that can be easily controlled. By the exploitation of different morphological structures of calcium sulfate, which acts as the active filler in a soft elastomer matrix, the magnitude of filler reinforcement can be reversibly altered, which will be reflected in changes of the final stiffness of the material. The higher stiffness, in other words, the higher modulus of the composites, is realized by the in situ development of fine nanostructured calcium sulfate dihydrate crystals, which are formed during exposure to water and, further, these highly reinforcing crystals can be transformed to a nonreinforcing hemihydrate mesocrystalline structure by simply heating the system in a controlled way. The Young's modulus of the developed material can be reversibly altered from ∼6 to ∼17 MPa, and the dynamic stiffness (storage modulus at room temperature and 10 Hz frequency) alters its value in the order of 1000%. As the transformation is related to the presence of water molecules in the crystallites, a hydrophilic elastomer matrix was selected, which is a blend of two hydrophilic polymers, namely, epichlorohydrin-ethylene oxide-allyl glycidyl ether terpolymer and a terpolymer of ethylene oxide-propylene oxide-allyl glycidyl ether. For the first time, this method also provides a route to regulate the morphology and structure of calcium sulfate nanocrystals in a confined ambient of cross-linked polymer chains.

Maxillofacial osseous reconstruction using the angular branch of the thoracodorsal vessels.

LENUS (Irish Health Repository)

Dolderer, Jürgen H

2010-09-01

Mandibular and maxillary resections can produce complex three-dimensional defects requiring skeletal, soft tissue, and epithelial reconstruction. The subscapular vascular axis offers a source of skin, bone, and muscle on a single pedicle for microvascular flap transfer. We reviewed four cases where the subscapular vascular pedicle was used as a source of tissue for complex facial reconstructions in maxillofacial defects. Reconstruction of these complex defects was performed with a latissimus dorsi muscle or myocutaneous flap in combination with the lateral border of the scapula, harvested on the angular branch of the thoracodorsal vessels. There were three cases of maxillectomy and one case of partial mandibulectomy for malignant tumors. In each case, the angular branch of the thoracodorsal artery supplied 6 to 8 cm of the lateral border of the scapula and a latissimus dorsi myocutaneous flap was used for soft tissue reconstruction. Follow-up ranged from 9 months to 3 years and in all cases there was successful bony union. Shoulder movement was normal. This series encourages the further use of subscapular axis flaps as flexible sources of combined myocutaneous and osseous flaps on a single vascular pedicle in cases of complex maxillofacial reconstruction.

Toward a predictive model for the failure of elastomer seals.

Science.gov (United States)

Molinari, Nicola; Khawaja, Musab; Sutton, Adrian; Mostofi, Arash; Baker Hughes Collaboration

Nitrile butadiene rubber (NBR) and hydrogenated-NBR (HNBR) are widely used elastomers, especially as seals in oil and gas industry. During exposure to the extreme temperatures and pressures typical of well-hole conditions, ingress of gases causes degradation of performance, including mechanical failure. Using computer simulations, we investigate this problem at two different length- and time-scales. First, starting with our model of NBR based on the OPLS all-atom force-field, we develop a chemically-inspired description of HNBR, where C=C double bonds are saturated with either hydrogen or intramolecular cross-links, mimicking the hydrogenation of NBR to form HNBR. We validate against trends for the mass density and glass transition temperature for HNBR as a function of cross-link density, and for NBR as a function of the fraction of acrylonitrile in the copolymer. Second, a coarse-grained approach is taken in order to study mechanical behaviour and to overcome the length- and time-scale limitations inherent to the all-atom model. The effect of nanoparticle fillers added to the elastomer matrix is investigated. Our initial focus is on understanding the mechanical properties at the elevated temperatures and pressures experienced in well-hole conditions. Baker Hughes.

Aetiology and incidence of maxillofacial trauma in Amsterdam: a retrospective analysis of 579 patients

NARCIS (Netherlands)

van den Bergh, B.; Karagozoglu, K.H.; Heymans, M.W.; Forouzanfar, T.

2012-01-01

Introduction The incidence of maxillofacial fractures varies widely between different countries. The large variability in reported incidence and aetiology is due to a variety of contributing factors, including environmental, cultural and socioeconomic factors. This retrospective report presents a

Aetiology and incidence of maxillofacial trauma in Amsterdam: a retrospective analysis of 579 patients

NARCIS (Netherlands)

van den Bergh, B.; Karagozoglu, K.H.; Heijmans, M.W.; Forouzanfar, T.

2012-01-01

Introduction: The incidence of maxillofacial fractures varies widely between different countries. The large variability in reported incidence and aetiology is due to a variety of contributing factors, including environmental, cultural and socioeconomic factors. This retrospective report presents a

Prevalence and patterns of combat sport related maxillofacial injuries.

Science.gov (United States)

Shirani, Gholamreza; Kalantar Motamedi, Mohammad Hosein; Ashuri, Alireza; Eshkevari, Pooyan Sadr

2010-10-01

This study was designed to assess the prevalence, distribution, and patterns of injury among athletes engaged in combat sports and compare the prevalence, pattern, and types of oral and maxillofacial trauma in these athletes. A total of 120 male athletes engaged in four combat sports (boxing, taekwondo, kickboxing, and Muay Thai) who had sustained bodily trauma were studied; 95 subjects with at least one traumatic injury to the face requiring treatment were referred to us by the physician team. The type of injury (facial laceration, facial fractures, jaw dislocation, etc.), site of facial injury (jaw, nose, malar bone, teeth, etc.), dental injuries (tooth fracture, displacement, luxation, and avulsion), causative sport (boxing, taekwondo, kickboxing, and Muay Thai) as well as demographic data were recorded. Injuries were examined clinically and radiographically, and treated accordingly by a specialist. Treatment data and demographics were recorded for each subject. Recorded data were assessed, and χ(2), ANOVA, and Kruskal-Wallis tests were used to statistically analyze and compare the data. Of 120 subjects, 95 male subjects (79.2%), aged 18-25 years (avg. 20 years), had at least one traumatic injury to the face requiring medical treatment. These injuries included facial laceration, bone fractures (nose, mandible, and zygoma), dental injuries (displacement, luxation, fracture, and avulsion), and mandibular dislocation which were recorded in 83 (69.2%), 55 (45.1%), 53 (44.2%), and 8 (6.7%) cases respectively. Statistically significant differences were encountered among various injuries and the sports; kickboxing caused the most maxillofacial injuries and was identified as more injurious. Tooth fractures (59.7%) were the most common dental injuries, and the nose (84.7%) was the most frequently fractured facial bone. Lacerations were more common in Thai-boxers (93.3%). Injuries were significantly greater in professional rather than amateur athletes. In this study

Prevalence and patterns of combat sport related maxillofacial injuries

Directory of Open Access Journals (Sweden)

Shirani Gholamreza

2010-01-01

Full Text Available Aim: This study was designed to assess the prevalence, distribution, and patterns of injury among athletes engaged in combat sports and compare the prevalence, pattern, and types of oral and maxillofacial trauma in these athletes. Materials and Methods: A total of 120 male athletes engaged in four combat sports (boxing, taekwondo, kickboxing, and Muay Thai who had sustained bodily trauma were studied; 95 subjects with at least one traumatic injury to the face requiring treatment were referred to us by the physician team. The type of injury (facial laceration, facial fractures, jaw dislocation, etc., site of facial injury (jaw, nose, malar bone, teeth, etc., dental injuries (tooth fracture, displacement, luxation, and avulsion, causative sport (boxing, taekwondo, kickboxing, and Muay Thai as well as demographic data were recorded. Injuries were examined clinically and radiographically, and treated accordingly by a specialist. Treatment data and demographics were recorded for each subject. Recorded data were assessed, and c2 , ANOVA, and Kruskal-Wallis tests were used to statistically analyze and compare the data. Results: Of 120 subjects, 95 male subjects (79.2%, aged 18-25 years (avg. 20 years, had at least one traumatic injury to the face requiring medical treatment. These injuries included facial laceration, bone fractures (nose, mandible, and zygoma, dental injuries (displacement, luxation, fracture, and avulsion, and mandibular dislocation which were recorded in 83 (69.2%, 55 (45.1%, 53 (44.2%, and 8 (6.7% cases respectively. Statistically significant differences were encountered among various injuries and the sports; kickboxing caused the most maxillofacial injuries and was identified as more injurious. Tooth fractures (59.7% were the most common dental injuries, and the nose (84.7% was the most frequently fractured facial bone. Lacerations were more common in Thai-boxers (93.3%. Injuries were significantly greater in professional rather

Transcatheter embolization for high blood flow vascular malformations of oral maxillofacial region

International Nuclear Information System (INIS)

Sun Zengtao; Liu Zuoqin; Li Jijun; Tang Jun; Shang Jianqiang; Chen Jie

2007-01-01

Objective: To explore the treatment and efficiency of high blood flow vascular malformations of oral maxillofacial region with super-selective arterial embolization. Methods: 18 cases underwent angiography of the head and neck before treatment and then followed by super-selective catheterization with microcatheter to embolize the feeding vessels of the vascular malformations with PVA. 8 cases underwent surgical excision within 72 hours after the embolization and the other 10 cases passed through the arterial radical emboliztion treatment. Results: Technical success ratio reached 100% with no complications causing skin necrosis or incorrect arterial embolization else where in the skull. All 8 cases undergone preoperative embolization showed obviously less bleeding, easier removal of the mass and reduction of operation time. 10 cases with radical arterial embolization manifested reduction of swelling and improvement of organ function within 1 to 24 months after the procedure. 5 patients were cured with only once operation, 4 cases with twice operation and 1 with the thrice. Conclusions: Aterial embolization is a safe and effective method in the treatment of high blood flow vascular malformations of oral maxillofacial region. (authors)

Dynamic characterization and modeling of magneto-rheological elastomers under compressive loadings

International Nuclear Information System (INIS)

Koo, J H; Khan, F; Jang, D D; Jung, H J

2009-01-01

The primary goal of this paper is to characterize and model the compression properties of Magneto-Rheological Elastomers (MREs). MRE samples were fabricated by curing a two component elastomer resin with 30% content of 10 μm sized iron particles by volume. In order to vary the magnetic field during compressive testing, a test fixture was designed and fabricated in which two permanent magnets could be variably positioned on either side of the specimen. By changing the distance between the magnets, the fixture allowed for varying the magnetic field that passes uniformly through the sample. Using this test setup and a dynamic test frame, a series of compression tests of MRE samples was performed by varying the magnetic field and frequency of loading. The results show the MR effect (percent increase in the materials 'stiffness') increases as the magnetic field increases and loading frequency increases within the range of the magnetic field and input frequency considered in this study. Furthermore, a phenomenological model was developed to capture the dynamic behaviours of the MREs under compression loadings.

Modelling and characterization of inflated dielectric elastomer actuators with tubular configuration

International Nuclear Information System (INIS)

Zhang, Chi; Chen, Hualing; Liu, Lei; Li, Dichen

2015-01-01

A dielectric elastomer undergoes large and fast deformation subject to external electric stimuli, making it a promising artificial muscle for various kinds of actuators, sensors and energy generators. This paper presents an actuator fabricated by (1) rolling a dielectric elastomer membrane, (2) pre-stretching the membrane along the radial direction and fixing the edges with rigid cylindrical plastic ends, and (3) applying a force to the end along the longitudinal direction and pumping air into the tube for inflation. Subject to a voltage, the structure works as an actuator with a large linear stroke. Governing equations of this actuator are established and simulation results are found to agree well with experimental results. We examine four modes of failure, namely loss of tension, electrical breakdown, snap-through instability and tensile rupture, with a variation in applied pressure. The actuating voltage is greatly reduced by applying pressure, providing the possibility of low-voltage driving. By regulating the applied pressure, large actuation strain and displacement are obtained simultaneously and the distributions of stretch, true stress and the true electric field become more homogeneous. (paper)

Integrated Force and Distance Sensing using Elastomer-Embedded Commodity Proximity Sensors.

Energy Technology Data Exchange (ETDEWEB)

Patel, Radhen [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Cox, Rebecca E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Correll, Nikolaus [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-02-01

We describe a combined proximity, contact and force (PCF) sensor based on a commodity infrared distance sensor embedded in a transparent elastomer with applications in robotic manipulation. Prior to contact, the sensor works as a distance sensor (0{6 cm), whereas after contact the material doubles as a spring, with force proportional to the compression of the elastomer (0{5 N). We describe its principle of operation and design parameters, including polymer thickness, mixing ratio, and emitter current, and show that the sensor response has an in ection point at contact that is independent of an object's surface properties, making it a robust detector for contact events. We then demonstrate how arrays of sensors, custom made for a standard Baxter gripper as well as embedded in the nger of the Kinova hand, can be used to (1) improve gripper alignment during grasping, (2) determine contact points with objects, (3) obtain simple 3D models using both proximity and touch, and (4) register point clouds from touch and RGB-D data.