Evaluation on occluded hydrocarbon in deep–ultra deep ancient source rocks and its cracked gas resources

Directory of Open Access Journals (Sweden)

Jian Li

2015-12-01

Full Text Available Oil-cracked gas, as the main type of high-over mature marine natural gas in China, is mainly derived from occluded hydrocarbon. So it is significant to carry out quantitative study on occluded hydrocarbon. In this paper, the occluded hydrocarbon volume of the main basins in China was calculated depending on their types, abundances and evolution stages by means of the forward method (experimental simulation and the inversion method (geologic profile dissection. And then, occluded hydrocarbon evolution models were established for five types of source rocks (sapropelic, sapropelic prone hybrid, humic prone hybrid, humic and coal. It is shown that the hydrocarbon expulsion efficiency of sapropelic and sapropelic prone hybrid excellent source rocks is lower than 30% at the low-maturity stage, 30%–60% at the principal oil generation stage, and 50%–80% at the high-maturity stage, which are all about 10% higher than that of humic prone hybrid and humic source rocks at the corresponding stages. The resource distribution and cracked gas expulsion of occluded hydrocarbon since the high-maturity stage of marine source rocks in the Sichuan Basin were preliminarily calculated on the basis of the evolution models. The cracked gas expulsion is 230.4 × 1012 m3 at the high evolution stage of occluded hydrocarbon of the Lower Cambrian Qiongzhusi Fm in this basin, and 12.3 × 1012 m3 from the source rocks of Sinian Doushantuo Fm, indicating good potential for natural gas resources. It is indicated that the favorable areas of occluded hydrocarbon cracked gas in the Qiongzhusi Fm source rocks in the Sichuan Basin include Gaoshiti–Moxi, Ziyang and Weiyuan, covering a favorable area of 4.3 × 104 km2.

Classes of organic molecules targeted by a methanogenic microbial consortium grown on sedimentary rocks of various maturities

Directory of Open Access Journals (Sweden)

Margaux eMesle

2015-06-01

Full Text Available Organic-rich shales are populated by methanogenic consortia that are able to degrade the fossilized organic matter into methane gas. To identify the organic fraction effectively degraded, we have sequentially depleted two types of organic-rich rocks, shales and coal, at two different maturities, by successive solvent extractions to remove the most soluble fractions (maltenes and asphaltenes and isolate kerogen. We show the ability of the consortia to produce methane from all rock samples, including those containing the most refractory organic matter, i.e. the kerogen. Shales yielded higher methane production than lignite and coal. Mature rocks yielded more methane than immature rocks. Surprisingly, the efficiency of the consortia was not influenced by the removal of the easily biodegradable fractions contained in the maltenes and asphaltenes. This suggests that one of the limitations of organic matter degradation in situ may be the accessibility of the carbon and energy source. Indeed, bitumen has a colloidal structure that may limit the accessibility to asphaltenes in the bulk rock. Solvent extractions might favor the access to asphaltenes and kerogen by modifying the spatial organization of the molecules in the rock matrix.

Characteristics of the Triassic Source Rocks of the Aitutu Formation in the (West Timor Basin

Directory of Open Access Journals (Sweden)

Asep Kurnia Permana

2014-12-01

Full Text Available DOI:10.17014/ijog.v1i3.192The Triassic rocks of the (West Timor Basin have been identified that was mainly deposited in the  marine environment. The fine grained clastics and carbonate  rocks of this Triassic marine  facies are considered to be the most promising source rocks potential in this basin. In this paper we present geochemical and petrographic data from outcrop samples of the Triassic carbonate Aitutu Formation, due to emphasized the organic maturation, kerogen type of the organic matter and the origin of the organic matter.  A representative of selected sample were subjected to the Rock-Eval Pyrolisis, vitrinite reflectance and thermal alteration index, bitumen extraction, were analyzed on the GC-MS. The samples were collected from marine deposit of the Triassic Sequence. The TOC values of the analyzed sample range between rich and rich organic richness (0.51% - 9.16%, wt.%, TOC, which consists mainly of type II and III kerogen and the organic matter consider to be predominantly oil/gas prone and gas prone potential. The thermal maturity assessed from Tmax, TAI, and vitrinite reflectance shows an immature to early peak mature stage of the organic matter. The GC-MS analyses of the biomarkers indicate mainly the organic matter derived from mixed source rocks facies containing alga debris and higher plant terrestrial origin.

Evaluation of the nature, origin and potentiality of the subsurface Middle Jurassic and Lower Cretaceous source rocks in Melleiha G-1x well, North Western Desert, Egypt

Directory of Open Access Journals (Sweden)

Mohamed M. El Nady

2015-09-01

Full Text Available The present work aims to evaluate the nature and origin of the source rock potentiality of subsurface Middle Jurassic and Lower Cretaceous source rocks in Melleiha G-1x well. This target was achieved throughout the evaluation of total organic carbon, rock Eval pyrolysis and vitrinite reflectance for fifteen cutting samples and three extract samples collected from Khatatba, Alam El Bueib and Kharita formations in the studied well. The result revealed that the main hydrocarbon of source rocks, for the Middle Jurassic (Khatatba Fm. is mainly mature, and has good capability of producing oil and minor gas. Lower Cretaceous source rocks (Alam El Bueib Fm. are mature, derived from mixed organic sources and have fair to good capability to generate gas and oil. Kharita Formation of immature source rocks originated from terrestrial origin and has poor to fair potential to produce gas. This indicates that Khatatba and Alam El Bueib formations take the direction of increasing maturity far away from the direction of biodegradation and can be considered as effective source potential in the Melleiha G-1x well.

Correlation of the Canol Formation source rock with oil from Norman Wells

Energy Technology Data Exchange (ETDEWEB)

Snowdon, L.R.; Brooks, P.W.; Williams, G.K.; Goodarzi, F.

1987-01-01

The source of the oil at Norman Wells has long been assumed to have been the Canol Formation and/or the Bluefish Member of the Hare Indian Formation. These two units are stratigraphically above and below the Kee Scarp Formation reservoir unit respectively, and are both bituminous shales. A wide range of analytical techniques including Rock-Eval pyrolysis, solvent extraction and fractionation, capillary gas chromatography, gas chromatography-mass spectrometry, and white light and fluorescence microscopy has been used to characterize core samples of these two units and two samples of crude oil from the Norman Wells field. Most of the analytical techniques were insufficiently refined to either differentiate the extracts from each other or to make a definitive oil/source rock correlation. Collision activated decomposition coupled with multiple ion detection mass spectrometry (GC-MS-MS) did provide sufficient chemical compositional detail of the oils and the two potential sources to demonstrate that the Canol Formation has been the effective source of the Normal Wells oil whereas the Bluefish Member has not. The level of thermal maturity of the core samples ranges from immature to moderately mature in the vicinity of the Norman Wells field to overmature for the samples obtained to the west and north of the field. The level of thermal maturity of the oil was observed to be somewhat higher than that of the samples of the source formation directly above the field. It was thus inferred that some lateral migration from more mature areas has occurred but the extent of this migration was not necessarily more than a few to tens of kilometers.

Depositional environment and source rock potential of Cenomanian and Turonian sedimentary rocks of the Tarfaya Basin, Southwest Morocco

Energy Technology Data Exchange (ETDEWEB)

Ghassal, B.I.; Littke, R.; Sachse, V.; Sindern, S.; Schwarzbauer, J.

2016-07-01

Detailed organic and inorganic geochemical analyses were used to assess the depositional environment and source rock potential of the Cenomanian and Turonian oil shale deposits in the Tarfaya Basin. This study is based on core samples from the Tarfaya Sondage-4 well that penetrated over 300m of Mid Cretaceous organic matter-rich deposits. A total of 242 samples were analyzed for total organic and inorganic carbon and selected samples for total sulfur and major elements as well as for organic petrology, Rock-Eval pyrolysis, Curie-Point-pyrolysis-gaschromatography-Mass-Spectrometry and molecular geochemistry of solvent extracts. Based on major elements the lower Cenomanian differs from the other intervals by higher silicate and lower carbonate contents. Moreover, the molecular geochemistry suggests anoxic bottom marine water conditions during the Cenomanian-Turonian Boundary Event (CTBE; Oceanic Anoxic Event 2: OAE2). As a proxy for the Sorg/Corg ratio, the ratio total thiophenes/total benzenes compounds was calculated from pyrolysate compositions. The results suggest that Sorg/ Corg is low in the lower Cenomanian, moderate in the upper Cenomanian, very high in the CTBE (CenomanianTuronian Boundary Event) and high in the Turonian samples. Rock-Eval data reveal that the lower Cenomanian is a moderately organic carbon-rich source rock with good potential to generate oil and gas upon thermal maturation. On the other hand, the samples from the upper Cenomanian to Turonian exhibit higher organic carbon content and can be classified as oil-prone source rocks. Based on Tmax data, all rocks are thermally immature. The microscopic investigations suggest dominance of submicroscopic organic matter in all samples and different contents of bituminite and alginite. The lower Cenomanian samples have little visible organic matter and no bituminite. The upper Cenomanian and CTBE samples are poor in bituminite and have rare visible organic matter, whereas the Turonian samples change

Lower Cretaceous Source Rock and its Implication for the Gulf of Guinea Petroleum System

International Nuclear Information System (INIS)

Frost, B.R.; Griffith, R.C.

2002-01-01

Current petroleum system models for the Gulf of Guinea propose Tertiary-age deltaic organic material as the principal source for the hydrocarbons found there. Although previous workers recognized numerous difficulties and inconsistencies, no alternative model has been resented to adequately explain the complete petroleum system. We propose that the principal source rock for the Gulf of Guinea system occurs in upper lower Cretaceous-age shales at the rift-drift transition. Tertiary loading and the consequent maturation of this lower Cretaceous source rock can explain the controls on tap formation, reservoir distribution and hydrocarbon types found in the Gulf of Guinea

Geochemistry of crude oils, seepage oils and source rocks from Belize and Guatemala

DEFF Research Database (Denmark)

Petersen, H.I.; Holland, B.; Nytoft, H.P.

2012-01-01

This study reviews the stratigraphy and the poorly documented petroleum geology of the Belize-Guatemala area in northern Central America. Guatemala is divided by the east-west trending La Libertad arch into the North and South Petén Basins. The arch is the westward continuation of the Maya...... generated from source rocks with similar thermal maturities. The crude oils were generated from marine carbonate source rocks and could be divided into three groups: Group 1 oils come from the North Petén Basin (Guatemala) and the western part of the Corozal Basin (Belize), and have a typical carbonate...

Tectono-thermal Evolution of the Lower Paleozoic Petroleum Source Rocks in the Southern Lublin Trough: Implications for Shale Gas Exploration from Maturity Modelling

Science.gov (United States)

Botor, Dariusz

2018-03-01

The Lower Paleozoic basins of eastern Poland have recently been the focus of intensive exploration for shale gas. In the Lublin Basin potential unconventional play is related to Lower Silurian source rocks. In order to assess petroleum charge history of these shale gas reservoirs, 1-D maturity modeling has been performed. In the Łopiennik IG-1 well, which is the only well that penetrated Lower Paleozoic strata in the study area, the uniform vitrinite reflectance values within the Paleozoic section are interpreted as being mainly the result of higher heat flow in the Late Carboniferous to Early Permian times and 3500 m thick overburden eroded due to the Variscan inversion. Moreover, our model has been supported by zircon helium and apatite fission track dating. The Lower Paleozoic strata in the study area reached maximum temperature in the Late Carboniferous time. Accomplished tectono-thermal model allowed establishing that petroleum generation in the Lower Silurian source rocks developed mainly in the Devonian - Carboniferous period. Whereas, during Mesozoic burial, hydrocarbon generation processes did not develop again. This has negative influence on potential durability of shale gas reservoirs.

Shale characterization in mass transport complex as a potential source rock: An example from onshore West Java Basin, Indonesia

Science.gov (United States)

Nugraha, A. M. S.; Widiarti, R.; Kusumah, E. P.

2017-12-01

This study describes a deep-water slump facies shale of the Early Miocene Jatiluhur/Cibulakan Formation to understand its potential as a source rock in an active tectonic region, the onshore West Java. The formation is equivalent with the Gumai Formation, which has been well-known as another prolific source rock besides the Oligocene Talang Akar Formation in North West Java Basin, Indonesia. The equivalent shale formation is expected to have same potential source rock towards the onshore of Central Java. The shale samples were taken onshore, 150 km away from the basin. The shale must be rich of organic matter, have good quality of kerogen, and thermally matured to be categorized as a potential source rock. Investigations from petrography, X-Ray diffractions (XRD), and backscattered electron show heterogeneous mineralogy in the shales. The mineralogy consists of clay minerals, minor quartz, muscovite, calcite, chlorite, clinopyroxene, and other weathered minerals. This composition makes the shale more brittle. Scanning Electron Microscope (SEM) analysis indicate secondary porosities and microstructures. Total Organic Carbon (TOC) shows 0.8-1.1 wt%, compared to the basinal shale 1.5-8 wt%. The shale properties from this outcropped formation indicate a good potential source rock that can be found in the subsurface area with better quality and maturity.

A chemical and thermodynamic model of oil generation in hydrocarbon source rocks

Science.gov (United States)

Helgeson, Harold C.; Richard, Laurent; McKenzie, William F.; Norton, Denis L.; Schmitt, Alexandra

2009-02-01

Thermodynamic calculations and Gibbs free energy minimization computer experiments strongly support the hypothesis that kerogen maturation and oil generation are inevitable consequences of oxidation/reduction disproportionation reactions caused by prograde metamorphism of hydrocarbon source rocks with increasing depth of burial.These experiments indicate that oxygen and hydrogen are conserved in the process.Accordingly, if water is stable and present in the source rock at temperatures ≳25 but ≲100 °C along a typical US Gulf Coast geotherm, immature (reduced) kerogen with a given atomic hydrogen to carbon ratio (H/C) melts incongruently with increasing temperature and depth of burial to produce a metastable equilibrium phase assemblage consisting of naphthenic/biomarker-rich crude oil, a type-II/III kerogen with an atomic hydrogen/carbon ratio (H/C) of ˜1, and water. Hence, this incongruent melting process promotes diagenetic reaction of detritus in the source rock to form authigenic mineral assemblages.However, in the water-absent region of the system CHO (which is extensive), any water initially present or subsequently entering the source rock is consumed by reaction with the most mature kerogen with the lowest H/C it encounters to form CO 2 gas and a new kerogen with higher H/C and O/C, both of which are in metastable equilibrium with one another.This hydrolytic disproportionation process progressively increases both the concentration of the solute in the aqueous phase, and the oil generation potential of the source rock; i.e., the new kerogen can then produce more crude oil.Petroleum is generated with increasing temperature and depth of burial of hydrocarbon source rocks in which water is not stable in the system CHO by a series of irreversible disproportionation reactions in which kerogens with higher (H/C)s melt incongruently to produce metastable equilibrium assemblages consisting of crude oil, CO 2 gas, and a more mature (oxidized) kerogen with a lower

The determination of maturity levels in source rocks of the La Luna Formation, Maracaibo Basin, Venezuela, based on convention geochemical parameters and asphaltenes; Determinacao do grau de maturacao em rochas geradoras de petroleo, formacao La Luna, Bacia de Maracaibo, Venezuela: parametros geoquimicos convencionais e asfaltenos

Energy Technology Data Exchange (ETDEWEB)

Castro, L.P. de [Pontificia Universidade Catolica (PUC-RS), Porto Alegre, RS (Brazil). Centro de Excelencia em Pesquisas sobre o Armazenamento de Carbono; Franco, N. [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil). Dept. de Geologia; Lopez, L.; Lo Monaco, S.; Escobar, G. [Universidad Central de Venezuela (UCV), Caracas (Venezuela); Kalkreuth, W. [Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alegre, RS (Brazil). Centro de Excelencia em Analises de Carvao e Rochas Geradoras de Petroleo

2008-07-01

The La Luna Formation, main source rock of the Maracaibo Basin was studied by conventional geochemical parameters, used to determine the maturity, and they were compared with the physic-chemical and molecular properties of the asphaltenes present in the bitumen of the rocks. Three wells were studied (A, B and C) with a total of 13 samples. Based on Rock-Eval results the organic matter in well A (455 deg C Tmax) shows a relatively high level of maturation (top of the oil window), whereas the organic matter in well B (435 - 436 deg C Tmax) is in the beginning of the oil window. Tmax values in well C (438 - 446 deg C) and well C suggest an intermediate maturity level. The biomarkers identified in well B and C show ratios indicating an equilibrium state in the maturity level. A good correlation was found comparing the conventional analytical data with the determination of maturity level obtained from the asphaltenes precipitated from the bitumen of the samples. With increased maturity levels the H1 NMR analysis showed enrichment in aromatic molecules in relation to aliphatic, due to the bitumen aromatization process. Similarly, the asphaltenes molecular weight has higher values in samples characterized by elevated maturity levels. This confirms earlier studies that showed that asphaltenes may be utilized as maturity parameter of organic matter. (author)

Organic geochemistry and petrology of oil source rocks, Carpathian Overthrust region, southeastern Poland - Implications for petroleum generation

Science.gov (United States)

Kruge, M.A.; Mastalerz, Maria; Solecki, A.; Stankiewicz, B.A.

1996-01-01

The organic mailer rich Oligocene Menilite black shales and mudstones are widely distributed in the Carpathian Overthrust region of southeastern Poland and have excellent hydrocarbon generation potential, according to TOC, Rock-Eval, and petrographic data. Extractable organic matter was characterized by an equable distribution of steranes by carbon number, by varying amounts of 28,30-dinor-hopane, 18??(H)-oleanane and by a distinctive group of C24 ring-A degraded triterpanes. The Menilite samples ranged in maturity from pre-generative to mid-oil window levels, with the most mature in the southeastern portion of the study area. Carpathian petroleum samples from Campanian Oligocene sandstone reservoirs were similar in biomarker composition to the Menilite rock extracts. Similarities in aliphatic and aromatic hydrocarbon distributions between petroleum asphaltene and source rock pyrolyzates provided further evidence genetically linking Menilite kerogens with Carpathian oils.

Organic compositions of lacustrine source rocks in Jiyang super-depression and its implication to petroleum geology

Institute of Scientific and Technical Information of China (English)

无

2006-01-01

The compositions of organic matter in four immature source rocks from Tertiary strata of Jiyang super-depression, the most typical continental rift subsidence basin in East China, have been studied by different extracting methods with CHCl3, MAC and CS2/NMP, respectively. The results suggest that there are great differences among the chemical compositions of organic matter in the source rocks derived from different depositional environments. About 79% of all the organic matter exists by non- covalent bond in the Es4 source rocks which were deposited under the saline lacustrine, indicating that its organic matter is not the real kerogen, but mainly composed of soluble organic matter which is easy to generate hydrocarbon at lower temperature. This is why the immature oils were derived from Es4 source rocks in Dongying depression. In contrast, around 60% of organic matter exists by covalent bond in Es3 source rocks which were deposited under the deep brackish-fresh lacustrine, showing that Es3 source rocks are mainly composed of kerogen producing mature hydrocarbon at higher temperature. The thermal simulation experiments, upon the remaining solid source rocks which were sequentially extracted by the three solvents, have been carried out. The chloroform extracts from the simulation product have been compared with the other three solvent extracts gained at room temperature. It is obvious that remarkable odd/even predominance (OEP) is mainly the characteristic of soluble organic matter; phytane mostly exists in the soluble organic matter by means of non-covalent bonds and characteristics of soluble organic matter are similar to these in immature oils produced in Jiyang super-depression.

Source rock contributions to the Lower Cretaceous heavy oil accumulations in Alberta: a basin modeling study

Science.gov (United States)

Berbesi, Luiyin Alejandro; di Primio, Rolando; Anka, Zahie; Horsfield, Brian; Higley, Debra K.

2012-01-01

The origin of the immense oil sand deposits in Lower Cretaceous reservoirs of the Western Canada sedimentary basin is still a matter of debate, specifically with respect to the original in-place volumes and contributing source rocks. In this study, the contributions from the main source rocks were addressed using a three-dimensional petroleum system model calibrated to well data. A sensitivity analysis of source rock definition was performed in the case of the two main contributors, which are the Lower Jurassic Gordondale Member of the Fernie Group and the Upper Devonian–Lower Mississippian Exshaw Formation. This sensitivity analysis included variations of assigned total organic carbon and hydrogen index for both source intervals, and in the case of the Exshaw Formation, variations of thickness in areas beneath the Rocky Mountains were also considered. All of the modeled source rocks reached the early or main oil generation stages by 60 Ma, before the onset of the Laramide orogeny. Reconstructed oil accumulations were initially modest because of limited trapping efficiency. This was improved by defining lateral stratigraphic seals within the carrier system. An additional sealing effect by biodegraded oil may have hindered the migration of petroleum in the northern areas, but not to the east of Athabasca. In the latter case, the main trapping controls are dominantly stratigraphic and structural. Our model, based on available data, identifies the Gordondale source rock as the contributor of more than 54% of the oil in the Athabasca and Peace River accumulations, followed by minor amounts from Exshaw (15%) and other Devonian to Lower Jurassic source rocks. The proposed strong contribution of petroleum from the Exshaw Formation source rock to the Athabasca oil sands is only reproduced by assuming 25 m (82 ft) of mature Exshaw in the kitchen areas, with original total organic carbon of 9% or more.

A study of light hydrocarbons (C{sub 4}-C{sub 1}3) in source rocks and petroleum fluid

Energy Technology Data Exchange (ETDEWEB)

Odden, Wenche

2000-07-01

This thesis consists of an introduction and five included papers. Of these, four papers are published in international journals and the fifth was submitted for review in April 2000. Emphasis has been placed on both naturally and artificially generated light hydrocarbons in petroleum fluids and their proposed source rocks as well as direct application of light hydrocarbons to oil/source rock correlations. Collectively, these papers describe a strategy for interpreting the source of the light hydrocarbons in original oils and condensates as well as the source of the asphaltene fractions from the reservoir fluids. The influence of maturity on light hydrocarbon composition has also been evaluated. The papers include (1) compositional data on the light hydrocarbons from thermal extracts and kerogen pyrolysates of sediment samples, (2) light hydrocarbon data of oils and condensates as well as the pyrolysis products of the asphaltenes from these fluids, (3) assessment of compositional alteration effects, such as selective losses of light hydrocarbons due to evaporation, thermal maturity, phase fractionation and biodegradation, (4) comparison of naturally and artificially generated light hydrocarbons, and (5) compound-specific carbon isotope analysis of the whole range of hydrocarbons of all sample types. (author)

A Study of Porphyrins in Petroleum Source Rocks

Energy Technology Data Exchange (ETDEWEB)

Huseby, Berit

1997-12-31

This thesis discusses several aspects of porphyrin geochemistry. Degradation experiments have been performed on the Messel oil shale (Eocene, Germany) to obtain information on porphyrins bound or incorporated into macromolecular structures. Thermal heating of the preextracted kerogen by hydrous pyrolysis was used to study the release of porphyrins and their temperature dependent changes during simulated diagenesis and catagenesis. Selective chemical degradation experiments were performed on the preextracted sediment to get more detailed information about porphyrins that are specifically bound to the macromolecular structures via ester bonds. From the heating experiments, in a separate study, the porphyrin nitrogen content in the generated bitumens was compared to the bulk of organic nitrogen compounds in the fraction. The bulk nitrogen contents in the generated bitumens, the water phase and the residual organic matter was recorded to establish the distribution of nitrogen between the kerogen and product phases. Porphyrins as biomarkers were examined in naturally matured Kimmeridge clay source rocks (Upper Jurassic, Norway), and the use of porphyrins as general indicators of maturity was evaluated. Underlying maturity trends in the biomarker data was investigated by Partial Least Squares analysis. Porphyrin as indicators of depositional conditions was also addressed, where the correlations between the (amounts) abundance of nickel and vanadyl porphyrins were mapped together with other descriptors that are assumed to be indicative of redox depositional conditions. 252 refs., 28 figs., 4 tabs.

A Study of Porphyrins in Petroleum Source Rocks

Energy Technology Data Exchange (ETDEWEB)

Huseby, Berit

1996-12-31

This thesis discusses several aspects of porphyrin geochemistry. Degradation experiments have been performed on the Messel oil shale (Eocene, Germany) to obtain information on porphyrins bound or incorporated into macromolecular structures. Thermal heating of the preextracted kerogen by hydrous pyrolysis was used to study the release of porphyrins and their temperature dependent changes during simulated diagenesis and catagenesis. Selective chemical degradation experiments were performed on the preextracted sediment to get more detailed information about porphyrins that are specifically bound to the macromolecular structures via ester bonds. From the heating experiments, in a separate study, the porphyrin nitrogen content in the generated bitumens was compared to the bulk of organic nitrogen compounds in the fraction. The bulk nitrogen contents in the generated bitumens, the water phase and the residual organic matter was recorded to establish the distribution of nitrogen between the kerogen and product phases. Porphyrins as biomarkers were examined in naturally matured Kimmeridge clay source rocks (Upper Jurassic, Norway), and the use of porphyrins as general indicators of maturity was evaluated. Underlying maturity trends in the biomarker data was investigated by Partial Least Squares analysis. Porphyrin as indicators of depositional conditions was also addressed, where the correlations between the (amounts) abundance of nickel and vanadyl porphyrins were mapped together with other descriptors that are assumed to be indicative of redox depositional conditions. 252 refs., 28 figs., 4 tabs.

Geochemistry of coal-measure source rocks and natural gases in deep formations in Songliao Basin, NE China

Energy Technology Data Exchange (ETDEWEB)

Mi, Jingkui; Zhang, Shuichang; Hu, Guoyi; He, Kun [State Key Laboratory for Enhanced Oil Recovery, Beijing (China); Petroleum Geology Research and Laboratory Center, Research Institute of Petroleum Exploration and Development, PetroChina (China); Key Laboratory for Petroleum Geochemistry, China National Petroleum Corp. (China)

2010-12-01

The natural gases developed in deep volcanic rock reservoirs of the Songliao Basin, NE China are characterized by enriched {delta}{sup 13}C value for methane and frequently reversal carbon isotopic distribution pattern. Although many researchers consider such gas type as an abiogenic origin, we believe the natural gases have a biogenic origin mainly except little inorganic gases and the reversal carbon isotopic distribution pattern of gases is caused by mixing of different origin gases. Methane carbon isotopic values for majority samples fall in the range from - 24 permille to - 32 permille, which is heavier than typical coal-type gases in other Chinese basins. There are several reasons caused heavy carbon isotope of methane: (1) Carbon isotopic values of source kerogen are 3-5 permille heavier than these from other basins; (2) Source rocks are at extremely high maturity stage with vitrinite reflectance mostly above 3.0%; (3) Portion of gas is derived from basement mudrock or slate with higher maturity. The observation on the organic from deep formation reveals that there is a relatively high content for liptinite, which reaches approximately 8 to 10%. The macerals component of source rock shows that the source rocks have some ability to generate oil. Small portion of oil was generated from high hydrogen content macerals in coals and shales as proof by oil found in microcrack and in micropore of coal and oil-bearing fluid inclusions grown in volcanic reservoir. The occurrence of pyrobitumen in volcanic reservoir indicates preexisted oil had been cracked into wet gas, and this kind of gas had also been found in gas pools. Heavy isotopic methane is derived from coal at extremely high maturity stage. There may be little inorganic alkane gases in deep layers for their geochemistry and special geological setting of Songliao Basin. Artificial mixing experiments of different origins gases confirm that inorganic gas such as gas from well FS1 mixed with other end members

Organic geochemical characterization of terrestrial source rocks of the Triassic Madygen formation (Southern Tien Shan, Kyrgyzstan)

Energy Technology Data Exchange (ETDEWEB)

Berner, U.; Scheeder, G.; Kus, J. [Section Geochemistry of Petroleum and Coal, BGR, Hannover (Germany); Voigt, S.; Schneider, J.W. [Geological Inst., TU Bergakademic Freiberg (Germany)

2009-09-15

Along the northern foothills of the Turkestan-Alai Range (SW Kyrgyzstan), a 1000 to 1500m thick succession of Mesozoic deposits is exposed recording regional changes of the paleo-landscape during Triassic to Cretaceous times. Detailed litho- and biofacies analyses, conducted by the TU Bergakademie Freiberg since 2006, provided for the first time a nearly complete columnar section of the continental Triassic Madygen Formation of Kyrgyzstan. Organic petrographical and organic geochemical methods (including RockEval pyrolyses, and biomarker analyses) have been applied to a suite of terrestrial sedimentary rocks of Triassic age with the intention to identify the depositional environment. Our investigations suggest that the potential source rocks of the terrestrial pluvial Madygen Formation might generate predominantly gaseous hydrocarbons at higher maturities. (orig.)

Burial history, thermal history and hydrocarbon generation modelling of the Jurassic source rocks in the basement of the Polish Carpathian Foredeep and Outer Carpathians (SE Poland)

Science.gov (United States)

Kosakowski, Paweł; Wróbel, Magdalena

2012-08-01

Burial history, thermal maturity, and timing of hydrocarbon generation were modelled for the Jurassic source rocks in the basement of the Carpathian Foredeep and marginal part of the Outer Carpathians. The area of investigation was bounded to the west by Kraków, to the east by Rzeszów. The modelling was carried out in profiles of wells: Będzienica 2, Dębica 10K, Góra Ropczycka 1K, Goleszów 5, Nawsie 1, Pławowice E1 and Pilzno 40. The organic matter, containing gas-prone Type III kerogen with an admixture of Type II kerogen, is immature or at most, early mature to 0.7 % in the vitrinite reflectance scale. The highest thermal maturity is recorded in the south-eastern part of the study area, where the Jurassic strata are buried deeper. The thermal modelling showed that the obtained organic matter maturity in the initial phase of the "oil window" is connected with the stage of the Carpathian overthrusting. The numerical modelling indicated that the onset of hydrocarbon generation from the Middle Jurassic source rocks was also connected with the Carpathian thrust belt. The peak of hydrocarbon generation took place in the orogenic stage of the overthrusting. The amount of generated hydrocarbons is generally small, which is a consequence of the low maturity and low transformation degree of kerogen. The generated hydrocarbons were not expelled from their source rock. An analysis of maturity distribution and transformation degree of the Jurassic organic matter shows that the best conditions for hydrocarbon generation occurred most probably in areas deeply buried under the Outer Carpathians. It is most probable that the "generation kitchen" should be searched for there.

Source rock evaluation and organic geochemistry of Belayim Marine Oil Field, Gulf of Suez, Egypt

Directory of Open Access Journals (Sweden)

Mohamed Abu Al-Atta

2014-09-01

In general, TOC analyses showed that the Nubia-A and B formation sediments are fairly immature compared to good source rocks with very high Hydrogen Index indicative of kerogen type II. The geochemical investigations of two oil samples indicate that the Upper Rudeis oil of Belayim Marine was derived from a marine carbonate rich source, which is relatively rich in algal organic matter and has moderate sulfur content. The maturity of the analyzed oils (about 0.75% R0 falls short from the stage of peak hydrocarbon generation which is known to be reached at about 0.85% R0.

Relationship of oil seep in Kudat Peninsula with surrounding rocks based on geochemical analysis

Science.gov (United States)

Izzati Azman, Nurul; Nur Fathiyah Jamaludin, Siti

2017-10-01

This study aims to investigate the relation of oil seepage at Sikuati area with the structural and petroleum system of Kudat Peninsula. The abundance of highly carbonaceous rocks with presence of lamination in the Sikuati Member outcrop at Kudat Peninsula may give an idea on the presence of oil seepage in this area. A detailed geochemical analysis of source rock sample and oil seepage from Sikuati area was carried out for their characterization and correlation. Hydrocarbon propectivity of Sikuati Member source rock is poor to good with Total Organic Carbon (TOC) value of 0.11% to 1.48%. and also categorized as immature to early mature oil window with Vitrinite Reflectance (VRo) value of 0.43% to 0.50 %Ro. Based on biomarker distribution, from Gas Chromatography (GC) and Gas Chromatography-Mass Spectrometry (GC-MS) analysis, source rock sample shows Pr/Ph, CPI and WI of 2.22 to 2.68, 2.17 to 2.19 and 2.46 to 2.74 respectively indicates the source rock is immature and coming from terrestrial environment. The source rock might be rich in carbonaceous material organic matter resulting from planktonic/bacterial activity which occurs at fluvial to fluvio-deltaic environment. Overall, the source rock from outcrop level of Kudat Peninsula is moderately prolific in term of prospectivity and maturity. However, as go far deeper beneath the surface, we can expect more activity of mature source rock that generate and expulse hydrocarbon from the subsurface then migrating through deep-seated fault beneath the Sikuati area.

Origin of a Tertiary oil from El Mahafir wildcat & geochemical correlation to some Muglad source rocks, Muglad basin, Sudan

Science.gov (United States)

Fadul Abul Gebbayin, Omer. I. M.; Zhong, Ningning; Ali Ibrahim, Gulfan; Ali Alzain, Mohamed

2018-01-01

Source rock screening analysis was performed on four stratigraphic units from the Muglad basin namely; Abu Gabra, Zarqa, Ghazal, and Baraka formations using pyrolysis and Vitrinite Reflectance (Ro). Results, integrated with the chromatographic and isotopic data from these rocks extracts and a Tertiary oil from El Mahafir-1 wild cat, were used to determine the origin of the oil. A good organic source within the Middle Abu Gabra Formation is observed in wells El Toor-6 and Neem Deep-1 (TOC, 1.0-2.0% & S2 5.0-10.0 mg C/g rock), with mixed kerogens I, II, & III, and thermally mature (% Ro = 0.74-0.94). The Campanian-Early Maastrichtian sequence, i.e. Zarqa and Ghazal formations are generally poor (TOC, diversity, both in space and time and is characterized by dominant algal input at some areas and or stratigraphic intervals [Elevated tricyclics, higher C29/C30 hopanes (0.5-1.14), and relatively low Gammacerane indices (4.6-14.4)], while mixed with abundant terrigenous material at others. A direct correlation between El Mahafir oil and the Abu Gabra extracts is thus inferred based on: its mixed organic source nature, oxic to sub-oxic depositional environment (Pr/Ph 1.22), relatively low C29/C30 hopanes (0.54), low C28 steranes (29%), and a high gammacerane index (20.5). This is largely supported by the maturity modeling results which suggest generation is only from the Abu Gabra at this location.

Mineralogical, chemical and K-Ar isotopic changes in Kreyenhagen Shale whole rocks and <2 µm clay fractions during natural burial and hydrous-pyrolysis experimental maturation

Science.gov (United States)

Clauer, Norbert; Lewan, Michael D.; Dolan, Michael P.; Chaudhuri, Sambhudas; Curtis, John B.

2014-01-01

Progressive maturation of the Eocene Kreyenhagen Shale from the San Joaquin Basin of California was studied by combining mineralogical and chemical analyses with K–Ar dating of whole rocks and sequence, indicating that there is no detectable variation in the crystallo-chemical organization of the K-bearing alumino-silicates with depth. No supply of K from outside of the rock volumes occurred, which indicates a closed-system behavior for it. Conversely, the content of the total organic carbon (TOC) content decreases significantly with burial, based on the progressive increasing Al/TOC ratio of the whole rocks. The initial varied mineralogy and chemistry of the rocks and their <2 μm fractions resulting from differences in detrital sources and depositional settings give scattered results that homogenize progressively during burial due to increased authigenesis, and concomitant increased alteration of the detrital material.

Maturation history modeling of Sufyan Depression, northwest Muglad Basin, Sudan

Science.gov (United States)

Wang, Ying; Liu, Luofu; An, Fuli; Wang, Hongmei; Pang, Xiongqi

2016-08-01

The Sufyan Depression is located in the northwest of Muglad Basin and is considered as a favorable exploration area by both previous studies and present oil shows. In this study, 16 wells are used or referred, the burial history model was built with new seismic, logging and well data, and the thermal maturity (Ro, %) of proved AG source rocks was predicted based on heat flow calculation and EASY %Ro modeling. The results show that the present heat flow range is 36 mW/m2∼50 mW/m2 (average 39 mW/m2) in 13 wells and 15 mW/m2∼55 mW/m2 in the whole depression. Accordingly, the geothermal gradient is 20 °C/km∼26 °C/km and 12 °C/km∼30 °C/km, respectively. The paleo-heat flow has three peaks, namely AG-3 period, lower Bentiu period and Early Paleogene, with the value decreases from the first to the last, which is corresponding to the tectonic evolution history. Corresponding to the heat flow distribution feature, the AG source rocks become mature earlier and have higher present marurity in the south area. For AG-2_down and AG-3_up source rocks that are proved to be good-excellent, most of them are mature with Ro as 0.5%-1.1%. But they can only generate plentiful oil and gas to charge reservoirs in the middle and south areas where their Ro is within 0.7%-1.1%, which is consistent with the present oil shows. Besides, the oil shows from AG-2_down reservoir in the middle area of the Sufyan Depression are believed to be contributed by the underlying AG-3_up source rock or the source rocks in the south area.

Source rock hydrocarbons. Present status

International Nuclear Information System (INIS)

Vially, R.; Maisonnier, G.; Rouaud, T.

2013-01-01

This report first presents the characteristics of conventional oil and gas system, and the classification of liquid and gaseous non conventional hydrocarbons, with the peculiar case of coal-bed methane. The authors then describe how source rock hydrocarbons are produced: production of shale oils and gases (horizontal drilling, hydraulic fracturing, exploitation) and of coal-bed methane and coal mine methane. In the next part, they address and discuss the environmental impact of source rock hydrocarbon production: installation footprint, water resource management, drilling fluids, fracturing fluids composition, toxicity and recycling, air pollution, induced seismicity, pollutions from other exploitation and production activities. They propose an overview of the exploitation and production of source rock gas, coal-bed gas and other non conventional gases in the world. They describe the current development and discuss their economic impacts: world oil context and trends in the USA, in Canada and other countries, impacts on the North American market, on the world oil industry, on refining industries, on the world oil balance. They analyse the economic impacts of non conventional gases: development potential, stakes for the world gas trade, consequence for gas prices, development opportunities for oil companies and for the transport sector, impact on CO 2 emissions, macro-economic impact in the case of the USA

Estimating thermal maturity in the Eagle Ford Shale petroleum system using gas gravity data

Science.gov (United States)

Birdwell, Justin E.; Kinney, Scott A.

2017-01-01

Basin-wide datasets that provide information on the geochemical properties of petroleum systems, such as source rock quality, product composition, and thermal maturity, are often difficult to come by or assemble from publically available data. When published studies are available and include these kinds of properties, they generally have few sampling locations and limited numbers and types of analyses. Therefore, production-related data and engineering parameters can provide useful proxies for geochemical properties that are often widely available across a play and in some states are reported in publically available or commercial databases. Gas-oil ratios (GOR) can be calculated from instantaneous or cumulative production data and can be related to the source rock geochemical properties like kerogen type (Lewan and Henry, 1999) and thermal maturity (Tian et al., 2013; U.S. Energy Information Administration [EIA], 2014). Oil density or specific gravity (SG), often reported in American Petroleum Institute units (°API = 141.5 /SG – 131.5), can also provide information on source rock thermal maturity, particularly when combined with GOR values in unconventional petroleum systems (Nesheim, 2017).

Low-maturity Kulthieth Formation coal: A possible source of polycyclic aromatic hydrocarbons in benthic sediment of the northern Gulf of Alaska

Science.gov (United States)

Van Kooten, G. K.; Short, J.W.; Kolak, J.J.

2002-01-01

The successful application of forensic geology to contamination studies involving natural systems requires identification of appropriate endmembers and an understanding of the geologic setting and processes affecting the systems. Studies attempting to delineate the background, or natural, source for hydrocarbon contamination in Gulf of Alaska (GOA) benthic sediments have invoked a number of potential sources, including seep oils, source rocks, and coal. Oil seeps have subsequently been questioned as significant sources of hydrocarbons present in benthic sediments of the GOA in part because the pattern of relative polycyclic aromatic hydrocarbon (PAH) abundance characteristic of benthic GOA sediments is inconsistent with patterns typical of weathered seep oils. Likewise, native coal has been dismissed in part because ratios of labile hydrocarbons to total organic carbon (e.g. PAH:TOC) for Bering River coal field (BRCF) sources are too low - i.e. the coals are over mature - to be consistent with GOA sediments. We present evidence here that native coal may have been prematurely dismissed, because BRCF coals do not adequately represent the geochemical signatures of coals elsewhere in the Kulthieth Formation. Contrary to previous thought, Kulthieth Formation coals east of the BRCF have much higher PAH: TOC ratios, and the patterns of labile hydrocarbons in these low thermal maturity coals suggest a possible genetic relationship between Kulthieth Formation coals and nearby oil seeps on the Sullivan anticline. Analyses of low-maturity Kulthieth Formation coal indicate the low maturity coal is a significant source of PAH. Source apportionment models that neglect this source will underestimate the contribution of native coals to the regional background hydrocarbon signature. ?? Published by Elsevier Science Ltd. on behalf of AEHS.

The source rock characters of U-rich granite

Energy Technology Data Exchange (ETDEWEB)

Mingyue, Feng; Debao, He [CNNC Key Laboratory of Uranium Resources Exploration and Evaluation Technology, Beijing Research Institute of Uranium Geology (China)

2012-03-15

This paper discusses the stratum composition, lithological association, uranium content of crust and the activation, migration, concentration of uranium at each tectonic cycle in South China. The authors point out that the source rock of U-rich granite is U-rich continental crust which is rich in Si, Al and K. The lithological association is mainly composed of terrestrial clastic rocks formation of mudstone and sandstone, mingled with intermediate-acidic, mafic pyroclastic rocks and carbonate rocks formation. During tectonic movements, the rocks had undergone regional metamorphism, migmatitization, granitization, and formed U-rich granites finally. (authors)

The source rock characters of U-rich granite

International Nuclear Information System (INIS)

Feng Mingyue; He Debao

2012-01-01

This paper discusses the stratum composition, lithological association, uranium content of crust and the activation, migration, concentration of uranium at each tectonic cycle in South China. The authors point out that the source rock of U-rich granite is U-rich continental crust which is rich in Si, Al and K. The lithological association is mainly composed of terrestrial clastic rocks formation of mudstone and sandstone, mingled with intermediate-acidic, mafic pyroclastic rocks and carbonate rocks formation. During tectonic movements, the rocks had undergone regional metamorphism, migmatitization, granitization, and formed U-rich granites finally. (authors)

Hydrocarbon potential of Ordovician and Silurian rocks. Siljan Region (Sweden)

Energy Technology Data Exchange (ETDEWEB)

Berner, U. [Bundesanstalt fuer Geowissenschaften und Rohstoffe (BGR), Hannover (Germany); Lehnert, O. [Erlangen-Nuernberg Univ., Erlangen (Germany); Meinhold, G. [Goettingen Univ. (Germany)

2013-08-01

Hydrocarbon exploration in the vicinity of Europe's largest impact structure (Siljan, Central Sweden) focused for years on abiogenic concepts and largely neglected state of the art knowledge on hydrocarbon generation via thermal decomposition of organic matter. In our study we use sedimentary rocks obtained from three drill sites (Mora001, Stumsnaes 1 and Solberga 1) within the ring structure around the central uplift to investigate the hydrocarbon potential of Ordovician and Silurian strata of the region and also for comparison with the shale oil and gas potential of age equivalent rocks of the Baltic Sea. Elemental analyses provided information on concentrations of carbonate and organic carbon, total sulfur as well as on the composition of major and minor elements of the sediments. The data has been used to evaluate the depositional environment and possible diagenetic alterations of the organic matter. RockEval pyrolysis and solvent hydrocarbon extraction gave insight into the hydrocarbon generation potential and the type and thermal maturity of the sediments. From the geochemistry data of the studied wells it is obvious that changes of depositional environments (lacustrine - marine) have occurred during Ordovician and Silurian times. Although, the quality of the organic matter has been influenced in marine and brackish environments through sulfate reduction, we observe for a number of marine and lacustrine sediments a good to excellent preservation of the biological precursors which qualify the sediments as hydrocarbon source rocks (Type II kerogens). Lacustrine source rocks show a higher remaining hydrocarbon potential (up to {proportional_to}550 mg HC per g C{sub org}) than those of marine or brackish environments. Our investigations indicate that the thermal maturity of organic matter of the drill sites has reached the initial stage of oil generation. However, at Mora001 some of the sediments were stained with oil indicating that hydrocarbons have

Geochemical characterization of Neogene sediments from onshore West Baram Delta Province, Sarawak: paleoenvironment, source input and thermal maturity

Science.gov (United States)

Togunwa, Olayinka S.; Abdullah, Wan H.

2017-08-01

The Neogene strata of the onshore West Baram Province of NW Borneo contain organic rich rock formations particularly within the Sarawak basin. This basin is a proven prolific oil and gas province, thus has been a subject of great interest to characterise the nature of the organic source input and depositional environment conditions as well as thermal maturation. This study is performed on outcrop samples of Lambir, Miri and Tukau formations, which are of stratigraphic equivalence to the petroleum bearing cycles of the offshore West Baram delta province in Sarawak. The investigated mudstone samples are organic rich with a total organic carbon (TOC) content of more than 1.0 wt.%. The integration of elemental and molecular analyses indicates that there is no significant variation in the source input between these formations. The investigated biomarkers parameters achieved from acyclic isoprenoids, terpanes and steranes biomarkers of a saturated hydrocarbon biomarkers revealed that these sediments contain high contribution of land plants with minor marine organic matter input that was deposited and preserved under relatively oxic to suboxic conditions. This is further supported by low total sulphur (TS), high TOC/TN ratios, source and redox sensitive trace elements (V, Ni, Cr, Co and Mo) concentrations and their ratios, which suggest terrigenous source input deposited under oxic to suboxic conditions. Based on the analysed biomarker thermal maturity indicators, it may be deduced that the studied sediments are yet to enter the maturity stage for hydrocarbon generation, which is also supported by measured vitrinite reflectance values of 0.39-0.48% Ro.

Geochemical characterization of Neogene sediments from onshore West Baram Delta Province, Sarawak: paleoenvironment, source input and thermal maturity

Directory of Open Access Journals (Sweden)

Togunwa Olayinka S.

2017-08-01

Full Text Available The Neogene strata of the onshore West Baram Province of NW Borneo contain organic rich rock formations particularly within the Sarawak basin. This basin is a proven prolific oil and gas province, thus has been a subject of great interest to characterise the nature of the organic source input and depositional environment conditions as well as thermal maturation. This study is performed on outcrop samples of Lambir, Miri and Tukau formations, which are of stratigraphic equivalence to the petroleum bearing cycles of the offshore West Baram delta province in Sarawak. The investigated mudstone samples are organic rich with a total organic carbon (TOC content of more than 1.0 wt.%. The integration of elemental and molecular analyses indicates that there is no significant variation in the source input between these formations. The investigated biomarkers parameters achieved from acyclic isoprenoids, terpanes and steranes biomarkers of a saturated hydrocarbon biomarkers revealed that these sediments contain high contribution of land plants with minor marine organic matter input that was deposited and preserved under relatively oxic to suboxic conditions. This is further supported by low total sulphur (TS, high TOC/TN ratios, source and redox sensitive trace elements (V, Ni, Cr, Co and Mo concentrations and their ratios, which suggest terrigenous source input deposited under oxic to suboxic conditions. Based on the analysed biomarker thermal maturity indicators, it may be deduced that the studied sediments are yet to enter the maturity stage for hydrocarbon generation, which is also supported by measured vitrinite reflectance values of 0.39-0.48% Ro.

Compound-specific C- and H-isotope compositions of enclosed organic matter in carbonate rocks: Implications for source identification of sedimentary organic matter and paleoenvironmental reconstruction

International Nuclear Information System (INIS)

Xiong Yongqiang; Wang Yanmei; Wang Yongquan; Xu Shiping

2007-01-01

The Bohai Bay Basin is one of the most important oil-producing provinces in China. Molecular organic geochemical characteristics of Lower Paleozoic source rocks in this area have been investigated by analyzing chemical and isotopic compositions of solvent extracts and acid-released organic matter from the Lower Paleozoic carbonate rocks in the Jiyang Sub-basin of the Bohai Bay Basin. The results indicate that enclosed organic matter in carbonate rocks has not been recognizably altered by post-depositional processes. Two end-member compositions are suggested for early organic matter trapped in the Lower Paleozoic carbonate rocks: (1) a source dominated by aquatic organisms and deposited in a relatively deep marine environment and (2) a relatively high saline, evaporative marine depositional environment. In contrast, chemical and isotopic compositions of solvent extracts from these Lower Paleozoic carbonate rocks are relatively complicated, not only inheriting original characteristics of their precursors, but also overprinted by various post-depositional alterations, such as thermal maturation, biodegradation and mixing. Therefore, the integration of both organic matter characteristics can provide more useful information on the origin of organic matter present in carbonate rocks and the environments of their deposition

Compound-specific C- and H-isotope compositions of enclosed organic matter in carbonate rocks: Implications for source identification of sedimentary organic matter and paleoenvironmental reconstruction

Energy Technology Data Exchange (ETDEWEB)

Xiong Yongqiang [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China)], E-mail: xiongyq@gig.ac.cn; Wang Yanmei; Wang Yongquan; Xu Shiping [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China)

2007-11-15

The Bohai Bay Basin is one of the most important oil-producing provinces in China. Molecular organic geochemical characteristics of Lower Paleozoic source rocks in this area have been investigated by analyzing chemical and isotopic compositions of solvent extracts and acid-released organic matter from the Lower Paleozoic carbonate rocks in the Jiyang Sub-basin of the Bohai Bay Basin. The results indicate that enclosed organic matter in carbonate rocks has not been recognizably altered by post-depositional processes. Two end-member compositions are suggested for early organic matter trapped in the Lower Paleozoic carbonate rocks: (1) a source dominated by aquatic organisms and deposited in a relatively deep marine environment and (2) a relatively high saline, evaporative marine depositional environment. In contrast, chemical and isotopic compositions of solvent extracts from these Lower Paleozoic carbonate rocks are relatively complicated, not only inheriting original characteristics of their precursors, but also overprinted by various post-depositional alterations, such as thermal maturation, biodegradation and mixing. Therefore, the integration of both organic matter characteristics can provide more useful information on the origin of organic matter present in carbonate rocks and the environments of their deposition.

Eo-Oligocene Oil Shales of the Talawi, Lubuktaruk, and Kiliranjao Areas, West Sumatra: Are they potential source rocks?

Directory of Open Access Journals (Sweden)

M. Iqbal

2014-12-01

Full Text Available DOI:10.17014/ijog.v1i3.198To anticipate the increasing energy demand, additional data and information covering unconventional fossil fuels such as oil shale must be acquired to promote the usage of alternative energy sources to crude oil. The Talawi and Lubuktaruk regions situated within intra-montane Ombilin Basin, and the Kiliranjao assumed to be a small intra montane basin are occupied by Eo-Oligocene sediments of Sangkarewang and Kiliran Formations, respectively. Field activity, geochemical screening techniques, and organic petrographic analysis, supported by SEM mode, are methods used. Most of the oil shale sequence is typically of an organically rich-succession comprising predominantly well-bedded, laminated and fissile, brownish to dark grey organic-rich shale and mudstone rocks. The exinite macerals within oil shale comprise mainly Pediastrum-lamalginite with minor cutinite, resinite, liptodetrinite, sporinite, bituminite, and rare Botryococcus-telalginite. Therefore; the oil shale deposits can be described as “lamosites”. Minor vitrinite maceral is also recognized. TOC analysis on selected shale samples corresponds to a fair up to excellent category of source rock characterization. The hydrogen index (HI for all samples shows a range of values from 207 - 864, and pyrolysis yield (PY ranges from 2.67 to 79.72 mg HC/g rock. The kerogen is suggested to be of mixed Type II and Type I autochthonous materials such as alginite, with minor allochthonous substances. Oil samples collected appear to be positioned within more oil prone rather than gas prone. Thermal maturity of the oil shales gained from Tmax value and production index (PI tends to show immature to marginally/early mature stage. A consistency in the thermal maturity level results by using both Tmax and vitrinite reflectance value is recognized. On the basis of  SEM analysis, the oil shale has undergone a late eodiagenetic process. Thereby, overall, vitrinite reflectance

Geochemical investigation of petroleum source rocks by using Rock- Eval data in the Agha-Jari oilfield

Directory of Open Access Journals (Sweden)

Behzad khani

2015-01-01

Full Text Available In this study, 40 drilling cutting of the Pabdeh, Gurpi, kazhdumi and Gadvan Formations from the Agha-Jari Oilfield were analyzed by using Rock-Eval pyrolysis. In order to recognizing sedimentary environmental conditions of studied Formations, they are divided to 4 zones which A (Kazhdumi Formation#187 and C (Kazhdumi Formation#140 zones show reduction conditions by presence of sea organic materials and B (Gadvan Formation #140 and D(Gadvan Formation#187 zones show oxidation conditions by presence of continental organic materials to basin. Based on the Rock-Eval pyrolysis data, the Pabeh, Gurpi, Kazhdumi and Gadvan Formations have variable hydrocarbon generative potential. HI vs. OI plot revealed that the kerogen type in this Formations is a mixed of types II & III. The intensity of matrix effect in the Pabdeh, Gurpi, Kazhdumi and Gadvan Formations was compared by using S2 vs. TOC plot and calculating its regression equation. The results show that the significant amount of S2 adsorption by matrix was happened in the Pabdeh (4.98-6.96 mg HC/gr rock in wells 113 and 121 and Gurpi Formations ‌(4.33 mg HC/gr rock in well 113 which is due to their low thermal maturity‌(Tmax

A Thermal Maturity Analysis of the Effective Cretaceous Petroleum System in the Southern Persian Gulf Basin

Directory of Open Access Journals (Sweden)

Majid Alipour

2017-10-01

Full Text Available Commercial hydrocarbon discoveries in the Cretaceous of the southern Persian Gulf basin provide direct evidence that there is an effective petroleum system associated with the Cretaceous series. The revised models of thermal maturity in this region are needed to investigate lateral and stratigraphic variations of thermal maturity, which have not so far been addressed in detail for this part of the Persian Gulf. Such thermal maturity models are required to delineate the existing play assessment risks and to predict properties in more deeply buried undrilled sections. This study uses two dimensional basin modeling techniques to reconstruct maturity evolution of the Cenomanian Middle Sarvak source rock, presumably the most likely source for these hydrocarbons. The results indicate that an estimated 900 meter difference in the depth of burial between the southeastern high and the adjacent trough tends to be translated into noticeable variations at both temperature (135 °C versus 162 °C and vitrinite reflectance (0.91% versus 1.35%. Since the organic matter in the mentioned source rock is of reactive type II, these could cause a shift of about 18 million years in the onset of hydrocarbon generation over respective areas.

Pre-Messinian (Sub-Salt Source-Rock Potential on Back-Stop Basins of the Hellenic Trench System (Messara Basin, Central Crete, Greece

Directory of Open Access Journals (Sweden)

Maravelis A.

2016-01-01

Full Text Available The Greek part of the Mediterranean Ridge suggests, in terms of its hydrocarbon potential, further frontier exploration. The geological similarities between its prolific portions, within the Cyprus and Egyptian Exclusive Economic Zones, indicate possible recoverable natural gas reserves in its Greek portion. Nevertheless it lacks of systematic frontier exploration although direct petroleum indicators occur. Active mud volcanoes on the Mediterranean Ridge, still emitting concurrently gas and gas hydrates, have not been yet assessed even though are strongly related to hydrocarbon occurrence worldwide (Caspian Sea, Gulf of Mexico, Western African Basin, Trinidad-Tobago, the Nile Cone. For this reason, the source rock potential of the Late Miocene lacustrine deposits on a backstop basin of the Hellenic Trench System (Messara Basin, Crete, Greece, was studied. The obtained pyrolysis data indicate that the containing organic matter is present in sufficient abundance and with good enough quality to be regarded as potential source rocks. The observed type III kerogen suggests gas generation potential. Although indications of higher thermal evolution occur the studied rocks suggest low maturation levels. The biogenic gas seeps in the studied research well further demonstrate the regional gas generation potential.

Distribution of organic carbon and petroleum source rock potential of Cretaceous and lower Tertiary carbonates, South Florida Basin: preliminary results

Science.gov (United States)

Palacas, James George

1978-01-01

Analyses of 134 core samples from the South Florida Basin show that the carbonates of Comanchean age are relatively richer in average organic carbon (0.41 percent) than those of Coahuilan age (0.28 percent), Gulfian age (0.18 percent) and Paleocene age (0.20 percent). They are also nearly twice as rich as the average world, wide carbonate (average 0.24 percent). The majority of carbonates have organic carbons less than 0.30 percent but the presence of many relatively organic rich beds composed of highly bituminous, argillaceous, highly stylolitic, and algal-bearing limestones and dolomites accounts for the higher percentage of organic carbon in some of the stratigraphic units. Carbonate rocks that contain greater than 0.4 percent organic carbon and that might be considered as possible petroleum sources were noted in almost each subdivision of the Coahuilan and Comanchean Series but particularly the units of Fredericksburg 'B', Trinity 'A', Trinity 'F', and Upper Sunniland. Possible source rocks have been ascribed by others to the Lower Sunniland, but lack of sufficient samples precluded any firm assessment in this initial report. In the shallower section of the basin, organic-rich carbonates containing as much as 3.2 percent organic carbon were observed in the lowermost part of the Gulfian Series and carbonate rocks with oil staining or 'dead' and 'live oil' were noted by others in the uppermost Gulfian and upper Cedar Keys Formation. It is questionable whether these shallower rocks are of sufficient thermal maturity to have generated commercial oil. The South Florida basin is still sparsely drilled and produces only from the Sunniland Limestone at an average depth of 11,500 feet (3500 m). Because the Sunniland contains good reservoir rocks and apparently adequate source rocks, and because the success rate of new oil field discoveries has increased in recent years, the chances of finding additional oil reserves in the Sunniland are promising. Furthermore, the

Oil(Gas) - source rock correlation technique

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-01

The overview of bio-marker parameters which are applicable to hydrocarbon exploration has been illustrated. Experimental analysis of saturated hydrocarbon and bio-markers of the Pohang E and F core samples has been carried out. Samples were extracted by stirring in dichloromethane at 40-50 degree for 10 hours. The saturated, aromatic and resin fractions of the extract were obtained using thin layer chromatograms. The relative abundance of normal alkane fraction of the samples is low except lowest interval, which is probably due to the biodegradation. The bio-marker assemblage of hopanoids and steranes has been characterized. According to the analysis of saturated hydrocarbons and bio-markers, the sedimentary environment of the Pohang core samples is marine and transitional zone except the terrestrial environment of the lowest samples such as 610.5 m from E core and 667.2 m from F core. The thermal maturity through the studied interval did not reach oil window even though slight increase in thermal maturity with depth, which coincide with Rock Eval pyrolysis data. In order to check the validation of analysis of the bio-markers, same samples were analyzed by the University of Louis Pasteur, France. The distribution and relative peak area of the bio-markers were identical with those by laboratory of KIGAM. For the 2 nd stage of the research, analysis of bio-markers other than hopanoids and steranes should be continued. (author). 29 figs., 7 tabs.

DEPOSITIONAL ENVIRONMENT AND ORGANIC GEOCHEMICAL CHARACTERISTICS OF LOWER EOCENE BITUMINOUS ROCKS, IN THE KÜRNÜÇ/GÖYNÜK-BOLU AREA

Directory of Open Access Journals (Sweden)

Ali SARI

2016-12-01

Full Text Available In this study, dark gray and dark brown colored, organic-carbon rich bituminous rocks (bituminous marl and bituminous shale exposing around the Kürnüç area (Göynük, Bolu are investigated by means of or- ganic geochemical characteristics. In this respect, rock lithologies, depositional environments, rock source potential, kerogen and organic maturity types and hydrocarbon generation potentials of bituminous rocks were determined. For this reason, pyrolysis (Rock Eval–VI analysis, gas chromatography (GC and gas chromatography-mass spectrometer (GC-MS analyses were carried out. In addition, spore color index (SCI was determined with organic petrographic method and stable carbon analysis (δ13C of the samples were also conducted. Lithology of the studied samples is of clastic source and the depositional environ- ment is a lagoon with a partial connection to the sea. In bituminous rocks with excellent source rock potential TOC values are in the range of 2.52-8.38 wt % (average 6.08 wt %. With the exception of two samples (Type II kerogen type of all samples is Type I. According to pyrolysis, GC and GC-MS organic maturity results, all the samples are in immature stage. Organic geochemical data indicate that bituminous rocks have an excellent oil generation potential and there is no organic contamination.

Characteristics of source rocks of the Datangpo Fm, Nanhua System, at the southeastern margin of Sichuan Basin and their significance to oil and gas exploration

Directory of Open Access Journals (Sweden)

Zengye Xie

2017-11-01

Full Text Available In recent years, much attention has been paid to the development environment, biogenetic compositions and hydrocarbon generation characteristics of ancient source rocks in the deep strata of the Sichuan Basin because oil and gas exploration extends continuously to the deep and ultra-deep strata and a giant gas field with the explored reserves of more than 1 × 1012 m3 was discovered in the Middle and Upper Proterozoic–Lower Paleozoic strata in the stable inherited paleo-uplift of the central Sichuan Basin. Based on the previous geological research results, outcrop section of the Datangpo Fm, Nanhua System, at the southeastern margin of the Sichuan Basin was observed and the samples taken from the source rocks were tested and analyzed in terms of their organic geochemistry and organic petrology. It is shown that high-quality black shale source rocks of the Datangpo Fm are developed in the tensional background at the southeastern margin of the Sichuan Basin between two glacial ages, i.e., Gucheng and Nantuo ages in the Nanhua Period. Their thickness is 16–180 m and mineral compositions are mainly clay minerals and clastic quartz. Besides, shale in the Datangpo Fm is of high-quality sapropel type source rock with high abundance at an over-mature stage, and it is characterized by low pristane/phytane ratios (0.32–0.83, low gammacerane abundance, high-abundance tricyclic terpane and higher-content C27 and C29 gonane, indicating that biogenetic compositions are mainly algae and microbes in a strong reducing environment with low salinity. It is concluded that the Datangpo Fm source rocks may be developed in the rift of Nanhua System in central Sichuan Basin. Paleo-uplifts and paleo-slopes before the Caledonian are the favorable locations for the accumulation of dispersed liquid hydrocarbons and paleo-reservoirs derived from the Datangpo Fm source rocks. In addition, scale accumulation zones of dispersed organic matter cracking gas and paleo

The Rho-GTPase effector ROCK regulates meiotic maturation of the bovine oocyte via myosin light chain phosphorylation and cofilin phosphorylation.

Science.gov (United States)

Lee, So-Rim; Xu, Yong-Nan; Jo, Yu-Jin; Namgoong, Suk; Kim, Nam-Hyung

2015-11-01

Oocyte meiosis involves a unique asymmetric division involving spindle movement from the central cytoplasm to the cortex, followed by polar body extrusion. ROCK is a Rho-GTPase effector involved in various cellular functions in somatic cells as well as oocyte meiosis. ROCK was previously shown to promote actin organization by phosphorylating several downstream targets, including LIM domain kinase (LIMK), phosphorylated cofilin (p-cofilin), and myosin light chain (MLC). In this study, we investigated the roles of ROCK and MLC during bovine oocyte meiosis. We found that ROCK was localized around the nucleus at the oocyte's germinal-vesicle (GV) stage, but spreads to the rest of the cytoplasm in later developmental stages. On the other hand, phosphorylated MLC (p-MLC) localized at the cortex, and its abundance decreased by the metaphase-II stage. Disrupting ROCK activity, via RNAi or the chemical inhibitor Y-27632, blocked both cell cycle progression and polar body extrusion. ROCK inhibition also resulted in decreased cortical actin, p-cofilin, and p-MLC levels. Similar to the phenotype associated with inhibition of ROCK activity, inhibition of MLC kinase by the chemical inhibitor ML-7 caused defects in polar body extrusion. Collectively, our results suggest that the ROCK/MLC/actomyosin as well as ROCK/LIMK/cofilin pathways regulate meiotic spindle migration and cytokinesis during bovine oocyte maturation. © 2015 Wiley Periodicals, Inc.

Effect of diagenesis on pore pressures in fine-grained rocks in the Egersund Basin, Central North Sea

OpenAIRE

Kalani, Mohsen; Zadeh, Mohammad Koochak; Jahren, Jens; Mondol, Nazmul Haque; Faleide, Jan Inge

2015-01-01

- Pore pressure in fine-grained rocks is important with respect to drilling problems such as kicks, blowouts, borehole instability, stuck pipe and lost circulation. In this study, a succession of overpressured, fine-grained, sedimentary rocks located in the Egersund Basin, Central North Sea, was analysed with respect to mineralogical composition, source-rock maturation and log-derived petrophysical properties to highlight the effect of diagenetic processes on the pore pressure. Pe...

Sedimentary environments and hydrocarbon potential of cretaceous rocks of indus basin, Pakistan

International Nuclear Information System (INIS)

Sheikh, S.A.; Naseem, S.

1999-01-01

Cretaceous rocks of Indus Basin of Pakistan are dominated by clastics with subordinate limestone towards the top. These rocks represent shelf facies and were deposited in deltaic to reducing marine conditions at variable depths. Indications of a silled basin with restricted circulation are also present. Cretaceous fine clastics/carbonates have good source and reservoir qualities. Variable geothermal gradients in different parts of basin have placed these rocks at different maturity levels; i.e. from oil to condensate and to gas. The potential of these rocks has been proved by several oil and gas discoveries particularly in the Central and Southern provinces of Indus Basin. (author)

Acoustic and Petrophysical Evolution of Organic-Rich Chalk Following Maturation Induced by Unconfined Pyrolysis

Science.gov (United States)

Shitrit, Omri; Hatzor, Yossef H.; Feinstein, Shimon; Vinegar, Harold J.

2017-12-01

Thermal maturation is known to influence the rock physics of organic-rich rocks. While most studies were performed on low-porosity organic-rich shales, here we examine the effect of thermal maturation on a high-porosity organic-rich chalk. We compare the physical properties of native state immature rock with the properties at two pyrolysis-simulated maturity levels: early-mature and over-mature. We further evaluate the applicability of results from unconfined pyrolysis experiments to naturally matured rock properties. Special attention is dedicated to the elastic properties of the organic phase and the influence of bitumen and kerogen contents. Rock physics is studied based on confined petrophysical measurements of porosity, density and permeability, and measurements of bedding-normal acoustic velocities at estimated field stresses. Geochemical parameters like total organic carbon (TOC), bitumen content and thermal maturation indicators are used to monitor variations in density and volume fraction of each phase. We find that porosity increases significantly upon pyrolysis and that P wave velocity decreases in accordance. Solids density versus TOC relationships indicate that the kerogen increases its density from 1.43 to 1.49 g/cc at the immature and early-mature stages to 2.98 g/cc at the over-mature stage. This density value is unusually high, although increase in S wave velocity and backscatter SEM images of the over-mature samples verify that the over-mature kerogen is significantly denser and stiffer. Using the petrophysical and acoustic properties, the elastic moduli of the rock are estimated by two Hashin-Shtrikman (HS)-based models: "HS + BAM" and "HS kerogen." The "HS + BAM" model is calibrated to the post-pyrolysis measurements to describe the mechanical effect of the unconfined pyrolysis on the rock. The absence of compaction in the pyrolysis process causes the post-pyrolysis samples to be extremely porous. The "HS kerogen" model, which simulates a

Characterizing the hypersiliceous rocks of Belgium used in (pre-)history: a case study on sourcing sedimentary quartzites

International Nuclear Information System (INIS)

Veldeman, Isis; Baele, Jean-Marc; De Doncker, H W J A; Goemaere, Eric; Deceukelaire, Marleen; Dusar, Michiel

2012-01-01

Tracking raw material back to its extraction source is a crucial step for archaeologists when trying to deduce migration patterns and trade contacts in (pre-)history. Regarding stone artefacts, the main rock types encountered in the archaeological record of Belgium are hypersiliceous rocks. This is a newly introduced category of rock types comprising those rocks made of at least 90% silica. These are strongly silicified quartz sands or sedimentary quartzites, siliceous rocks of chemical and biochemical origin (e.g. flint), very pure metamorphic quartzites and siliceous volcanic rocks (e.g. obsidian). To be able to distinguish between different extraction sources, ongoing research was started to locate possible extraction sources of hypersiliceous rocks and to characterize rocks collected from these sources. Characterization of these hypersiliceous rocks is executed with the aid of optical polarizing microscopy, optical cold cathodoluminescence and scanning-electron microscopy combined with energy-dispersive x-ray spectrometry and with back-scatter electron imaging. In this paper, we focus on various sedimentary quartzites of Paleogene stratigraphical level. (paper)

Experimental investigation of the role of rock fabric in gas generation and expulsion during thermal maturation: Anhydrous closed-system pyrolysis of a bitumen-rich Eagle Ford Shale

Science.gov (United States)

Shao, Deyong; Ellis, Geoffrey S.; Li, Yanfang; Zhang, Tongwei

2018-01-01

Gold-tube pyrolysis experiments were conducted on miniature core plugs and powdered rock from a bitumen-rich sample of Eagle Ford Shale to investigate the role of rock fabric in gas generation and expulsion during thermal maturation. The samples were isothermally heated at 130, 300, 310, 333, 367, 400, and 425 °C for 72 h under a confining pressure of 68.0 MPa, corresponding to six levels of induced thermal maturity: pre-oil generation (130 °C/72 h), incipient oil/bitumen generation (300 and 310 °C/72 h), early oil generation (333 °C/72 h), peak oil generation (367 °C/72 h), early oil cracking (400 °C/72 h), and late oil cracking (425 °C/72 h). Experimental results show that gas retention coupled with compositional fractionation occurs in the core plug experiments and varies as a function of thermal maturity. During the incipient oil/bitumen generation stage, yields of methane through pentane (C1–C5) from core plugs are significantly lower than those from rock powder, and gases from core plugs are enriched in methane. However, the differences in C1–C5 gas yield and composition decrease throughout the oil generation stage, and by the oil cracking stage no obvious compositional difference in C1–C5 gases exists. The decrease in the effect of rock fabric on gas yield and composition with increasing maturity is the result of an increase in gas expulsion efficiency. Pyrolysis of rock powder yields 4–16 times more CO2 compared to miniature core plugs, with δ13CCO2 values ranging from −2.9‰ to −0.6‰, likely due to carbonate decomposition accelerated by reactions with organic acids. Furthermore, lower yields of gaseous alkenes and H2 from core plug experiments sugge

Hydrocarbon Source Rock Potential of the Sinamar Formation, Muara Bungo, Jambi

Directory of Open Access Journals (Sweden)

Moh. Heri Hermiyanto Zajuli

2014-07-01

Full Text Available DOI: 10.17014/ijog.v1i1.175The Oligocene Sinamar Formation consists of shale, claystone, mudstone, sandstone, conglomeratic sandstone, and intercalation of coal seams. The objective of study was to identify the hydrocarbon source rock potential of the Sinamar Formation based on geochemichal characteristics. The analyses were focused on fine sediments of the Sinamar Formation comprising shale, claystone, and mudstone. Primary data collected from the Sinamar Formation well and outcrops were analyzed according to TOC, pyrolisis analysis, and gas chromatography - mass spectometry of normal alkanes that include isoprenoids and sterane. The TOC value indicates a very well category. Based on TOC versus Pyrolysis Yields (PY diagram, the shales of Sinamar Formation are included into oil prone source rock potential with good to excellent categories. Fine sediments of the Sinamar Formation tend to produce oil and gas originated from kerogen types I and III. The shales tend to generate oil than claystone and mudstone and therefore they are included into a potential source rock. 

Hydrocarbon Maturation and Os Mixing on Bolide Impact at the Frasnian-Famennian Boundary

Science.gov (United States)

Stein, H.; Zimmerman, A.; Yang, G.; Hannah, J.; Egenhoff, S.

2009-04-01

An intractable problem in the application of Re-Os geochemistry has been knowledge of the distribution of Re and Os between source rock and generated hydrocarbon. Solutions lie in combined experimental work with controlled and induced maturation, and field studies optimized by known source rock and time of hydrocarbon generation. The Siljan impact site with its variably tilted but largely intact Ordovician-Silurian sections provides an unsurpassed opportunity to examine the Re-Os systematics of source rock and generated crude oil, and the Re-Os imprint of the bolide. This three-component system contains (1) a time pin for maturation (377 ± 2 Ma; laser argon dating of impact melt, Reimold et al. 2005) arguably at the Frasnian-Famennian boundary, (2) known source rocks with kerogens still intact, and (3) crude oils generated on impact. Modeling takes into consideration the possibility of pre-impact maturation as well. At Siljan, numerous quarries expose the Upper Ordovician Boda and Kullsberg limestone mounds, and locally, the underlying and laterally equivalent Tretaspis (Fjäcka) shale. We obtained a sample of crude oil seeping from a drill hole in the quarry floor at Solberga. Preliminary Re-Os analyses on four aliquots of this oil form an excellent linear array in 187Re/188Os versus 187Os/188Os space. The associated age, however, is impossibly old (Neoproterozoic), and the initial 187Os/188Os unreasonably low (0.2). Rather, this linear array fits a mixing line between a meteoritic component and a hydrocarbon generated from the Tretaspis shale. We are presently performing further tests to isolate the two end-members. Filtering suggests that the extraterrestrial component consists of small physical particles which can be largely removed from the petroleum fraction. The extreme contrast in Re-Os composition between meteorite (known) and black shale (in progress) end-members maximizes the sensitivity of the isotopic study. Reimold, W.U., Kelley, S.P., Sherlock, S

Depositional environments and oil potential of Jurassic/Cretaceous source rocks within the Seychelles microcontinent

Energy Technology Data Exchange (ETDEWEB)

Plummer, P.S.; Joseph, P.R.; Samson, P.J. [Seychelles National Oil Co., Mahe (Seychelles)

1998-12-31

The Seychelles microcontinent became isolated between the Somali, Mascarene and Arabian basins of the Indian Ocean as a result of the Mesozoic fragmentation of Gondwana. Major rifting events occurred during the Triassic-Middle Jurassic and Late Cretaceous (Cenomanian-Santonian and Maastrichtian) during which shaly source rock facies accumulated in principally marginal marine/deltaic environments. Between these times, post-rift passive margin deposition within restricted to open marine environments produced shaly source rocks during late Middle Jurasic-Early Cretaceous, Campanian-Maastrichtian and Paleocene times. Recent geochemical analysis of cuttings from the Seagull Shoals-1 well has identified an oil-prone liptinitic (Type II) coaly shale within early Middle Jurassic abandoned deltaic deposits. This coaly source rock is regionally developed, having also been identified in the Majunja and Morondava basins of Madagascar. Oil-prone Type II organic matter has also been identified in the Owen Bank A-1 well within restricted marine shales of late Middle Jurassic age. These shales are part of a thick post-rift source rock sequence that extends into the Early Cretaceous and is in part correlative with the proven Late Jurassic Uarandab Shale of Somalia. Analysis of Campanian marine shales from Reith Bank-1 well identified significant dilution of total organic carbon content in composite, compared to picked, well cuttings samples. This finding supports a published inference that these post-rift shales have source rock potential. (author)

Hydrocarbon source rock potential evaluation of the Late Paleocene ...

Indian Academy of Sciences (India)

63

research is available on its source rock potential evaluation at Nammal Gorge Section in the Salt. Range, Potwar Basin .... methods of Tucker (2003) and Assaad (2008) have been followed. A total of fifteen ..... Business Media. Baker D M, Lillie ...

Organic geochemistry investigations of crude oils from Bayoot oilfield in the Masila Basin, east Yemen and their implication for origin of organic matter and source-related type

Directory of Open Access Journals (Sweden)

Mohammed Hail Hakimi

2018-03-01

Full Text Available Thirteen crude oil samples from fractured basement reservoir rocks in the Bayoot oilfield, Masila Basin were studied to describe oil characteristics and to provide information on the source of organic matter input and the genetic link between oils and their potential source rock in the basin. The bulk geochemical results of whole oil and gasoline hydrocarbons indicate that the Bayoot oils are normal crude oil, with high hydrocarbons of more than 60%. The hydrocarbons are dominated by normal, branched and cyclic alkanes a substantial of the light aromatic compounds, suggesting aliphatic oil-prone kerogen. The high abundant of normal, branched and cyclic alkanes also indicate that the Bayoot oils are not biodegradation oils.The biomarker distributions of isoprenoid, hopane, aromatic and sterane and their cross and triangular plots suggest that the Bayoot oils are grouped into one genetic family and were generated from marine clay-rich source rock that received mixed organic matter and deposited under suboxic conditions. The biomarker distributions of the Bayoot oils are consistent with those of the Late Jurassic Madbi source rock in the basin. Biomarker maturity and oil compositions data also indicate that the Bayoot oils were generated from mature source rock with peak oil-window maturity. Keywords: Crude oil, Basement reservoir rocks, Biomarker, Organic source input, Bayoot oilfield, Masila Basin

On the source material of magmas - with special reference to Nd isotopic ratios of igneous rocks

International Nuclear Information System (INIS)

Shuto, Kenji

1980-01-01

In 1973, the Sm-Nd method was first used for the measurement of the absolute age of igneous rocks and meteorites. Subsequently in the following years, the research works by means of the Nd isotopic ratio in igneous rocks have been made strenuously in order to reveal the chemistry of the source materials of magma giving rise to the igneous rocks and further the evolution process of mantle and earth's crust. The fundamental items for the Sm-Nd method are explained. Then, the research results more important in the above connection are given. Finally, the ideas by the author concerning the source materials of magma are presented from the data available on the Nd isotopes in meteorites and igneous rocks. The following matters are described: the fundamentals of Sm-Nd method, the Nd content in seawater, the negative correlation between Nd and Sr isotopic ratios in igneous rocks, magma source materials and Nd isotopes, and considerations on magma source materials. (J.P.N.)

Applying Bioaugmentation to Treat DNAPL Sources in Fractured Rock

Science.gov (United States)

2017-03-27

Figure 1. This ESTCP demonstration was focused in the vicinity of Building 8595, adjacent to the location of a reported surface release of PCE ( Earth ...electron donor source, such as vegetable oil, is typically used in passive approaches. When treating a DNAPL source area in fractured rock, there are... vegetable oil) are used. Hydrogen The generation of hydrogen can be used to verify fermentation of electron donor. Metals (Fe, Mn, As) Increase

Oils and source rocks from the Anadarko Basin: Final report, March 1, 1985-March 15, 1995

Energy Technology Data Exchange (ETDEWEB)

Philp, R. P. [School of Geology and Geophysics, Univ. of Oklahoma, Norman, OK (United States)

1996-11-01

The research project investigated various geochemical aspects of oils, suspected source rocks, and tar sands collected from the Anadarko Basin, Oklahoma. The information has been used, in general, to investigate possible sources for the oils in the basin, to study mechanisms of oil generation and migration, and characterization of depositional environments. The major thrust of the recent work involved characterization of potential source formations in the Basin in addition to the Woodford shale. The formations evaluated included the Morrow, Springer, Viola, Arbuckle, Oil Creek, and Sylvan shales. A good distribution of these samples was obtained from throughout the basin and were evaluated in terms of source potential and thermal maturity based on geochemical characteristics. The data were incorporated into a basin modelling program aimed at predicting the quantities of oil that could, potentially, have been generated from each formation. The study of crude oils was extended from our earlier work to cover a much wider area of the basin to determine the distribution of genetically-related oils, and whether or not they were derived from single or multiple sources, as well as attempting to correlate them with their suspected source formations. Recent studies in our laboratory also demonstrated the presence of high molecular weight components(C{sub 4}-C{sub 80}) in oils and waxes from drill pipes of various wells in the region. Results from such a study will have possible ramifications for enhanced oil recovery and reservoir engineering studies.

Biomarkers, carbon isotopic composition and source rock potentials of Awgu coals, middle Benue trough, Nigeria

Science.gov (United States)

Adedosu, Taofik A.; Sonibare, Oluwadayo O.; Tuo, Jincai; Ekundayo, Olusegun

2012-05-01

Coal and carbonaceous shale samples were collected from two boreholes (BH 94 and BH 120) in Awgu formation of Middle Benue Trough, Nigeria. Source rock potentials of the samples were studied using biomarkers and carbon isotopic composition. Biomarkers in the aliphatic fractions in the samples were studied using Gas Chromatography-Mass Spectrometry (GC-MS). The Carbon isotope analysis of individual n-alkanes in the aliphatic fraction was performed using Gas Chromatography-Combustion-Isotope Ratio Mass Spectrometer (GC-IRMS). The abundance of hopanes, homohopanes (C31-C35), and C29 steranes in the samples indicate terrestrial plant, phytoplankton and cyanobacteria contributions to the organic matter that formed the coal. High (Pr/Ph) ratio (3.04-11.07) and isotopic distribution of individual alkanes showed that the samples consisted of mixed terrestrial/marine organic matter deposited under oxic condition in lacustrine-fluvial/deltaic depositional environment. The maturity parameters derived from biomarker distributions showed that the samples are in the main phase of oil window.

Restoration of Circum-Arctic Upper Jurassic source rock paleolatitude based on crude oil geochemistry

Science.gov (United States)

Peters, K.E.; Ramos, L.S.; Zumberge, J.E.; Valin, Z.C.; Scotese, C.R.

2008-01-01

Tectonic geochemical paleolatitude (TGP) models were developed to predict the paleolatitude of petroleum source rock from the geochemical composition of crude oil. The results validate studies designed to reconstruct ancient source rock depositional environments using oil chemistry and tectonic reconstruction of paleogeography from coordinates of the present day collection site. TGP models can also be used to corroborate tectonic paleolatitude in cases where the predicted paleogeography conflicts with the depositional setting predicted by the oil chemistry, or to predict paleolatitude when the present day collection locality is far removed from the source rock, as might occur due to long distance subsurface migration or transport of tarballs by ocean currents. Biomarker and stable carbon isotope ratios were measured for 496 crude oil samples inferred to originate from Upper Jurassic source rock in West Siberia, the North Sea and offshore Labrador. First, a unique, multi-tiered chemometric (multivariate statistics) decision tree was used to classify these samples into seven oil families and infer the type of organic matter, lithology and depositional environment of each organofacies of source rock [Peters, K.E., Ramos, L.S., Zumberge, J.E., Valin, Z.C., Scotese, C.R., Gautier, D.L., 2007. Circum-Arctic petroleum systems identified using decision-tree chemometrics. American Association of Petroleum Geologists Bulletin 91, 877-913]. Second, present day geographic locations for each sample were used to restore the tectonic paleolatitude of the source rock during Late Jurassic time (???150 Ma). Third, partial least squares regression (PLSR) was used to construct linear TGP models that relate tectonic and geochemical paleolatitude, where the latter is based on 19 source-related biomarker and isotope ratios for each oil family. The TGP models were calibrated using 70% of the samples in each family and the remaining 30% of samples were used for model validation. Positive

Microwave-assisted nonionic surfactant extraction of aliphatic hydrocarbons from petroleum source rock

Energy Technology Data Exchange (ETDEWEB)

Akinlua, A., E-mail: geochemresearch@yahoo.com [Fossil Fuels and Environmental Geochemistry Group, Department of Chemistry, Obafemi Awolowo University, Ile-Ife (Nigeria); Jochmann, M.A.; Laaks, J.; Ewert, A.; Schmidt, T.C. [Instrumental Analytical Chemistry, University Duisburg-Essen, Universitaetsstr, 5, 45141 Essen (Germany)

2011-04-08

The extraction of aliphatic hydrocarbons from petroleum source rock using nonionic surfactants with the assistance of microwave was investigated and the conditions for maximum yield were determined. The results showed that the extraction temperatures and kinetic rates have significant effects on extraction yields of aliphatic hydrocarbons. The optimum temperature for microwave-assisted nonionic surfactant extraction of aliphatic hydrocarbons from petroleum source rock was 105 deg. C. The optimum extraction time for the aliphatic hydrocarbons was at 50 min. Concentration of the nonionic surfactant solution and irradiation power had significant effect on the yields of aliphatic hydrocarbons. The yields of the analytes were much higher using microwave assisted nonionic surfactant extraction than with Soxhlet extraction. The recoveries of the n-alkanes and acyclic isoprenoid hydrocarbons for GC-MS analysis from the extractant nonionic surfactant solution by in-tube extraction (ITEX 2) with a TENAX TA adsorbent were found to be efficient. The results show that microwave-assisted nonionic surfactant extraction (MANSE) is a good and efficient green analytical preparatory technique for geochemical evaluation of petroleum source rock.

Microwave-assisted nonionic surfactant extraction of aliphatic hydrocarbons from petroleum source rock

International Nuclear Information System (INIS)

Akinlua, A.; Jochmann, M.A.; Laaks, J.; Ewert, A.; Schmidt, T.C.

2011-01-01

The extraction of aliphatic hydrocarbons from petroleum source rock using nonionic surfactants with the assistance of microwave was investigated and the conditions for maximum yield were determined. The results showed that the extraction temperatures and kinetic rates have significant effects on extraction yields of aliphatic hydrocarbons. The optimum temperature for microwave-assisted nonionic surfactant extraction of aliphatic hydrocarbons from petroleum source rock was 105 deg. C. The optimum extraction time for the aliphatic hydrocarbons was at 50 min. Concentration of the nonionic surfactant solution and irradiation power had significant effect on the yields of aliphatic hydrocarbons. The yields of the analytes were much higher using microwave assisted nonionic surfactant extraction than with Soxhlet extraction. The recoveries of the n-alkanes and acyclic isoprenoid hydrocarbons for GC-MS analysis from the extractant nonionic surfactant solution by in-tube extraction (ITEX 2) with a TENAX TA adsorbent were found to be efficient. The results show that microwave-assisted nonionic surfactant extraction (MANSE) is a good and efficient green analytical preparatory technique for geochemical evaluation of petroleum source rock.

Relationship between fluvial clastic sediment and source rock abundance in Rapti river basin of central Nepal Himalayas

International Nuclear Information System (INIS)

Tamrakar Naresh Kazi; Shresth Madhusudan Bhakta

2008-01-01

Many tributaries from carbonate sedimentary, metamorphic and igneous rocks of the Lesser Himalayan and clastic sedimentary rocks of the Sub-Himalayan Ranges carry gravelly sediments to the Rapti River. River bar sediments were analyzed for composition and texture to evaluate downstream changes in properties, and to establish relationship between proportion of clasts and the abundance of rock types in the source areas. Percent quartzite clast or granite clast increases whereas that of carbonate, schist or slate decreases along downstream. The largest grain size decreases downstream, whereas fatness index and sphericity tend to increase. Despite of little diminish in relative abundance of rock types in source areas along the river, the relative proportion of corresponding clast type shows rapid reduction (e.g. slate or phyllite or carbonate clasts) or rapid enhancement (e.g. granite clast). The relationships of quartzite clast and schist clasts with their corresponding source rocks are statistically significant suggesting that these clasts can provide clue to source rock abundance. About 85 to 94% of the gravel clasts represent rock types of the Lesser Himalayan Range suggesting that this range has been contributing enormous amount of sediments.

Reconstruction of burial history, temperature, source rock maturity and hydrocarbon generation in the northwestern Dutch offshore

NARCIS (Netherlands)

Abdul Fattah, R.; Verweij, J.M.; Witmans, N.; Veen, J.H. ten

2012-01-01

3D basin modelling is used to investigate the history of maturation and hydrocarbon generation on the main platforms in the northwestern part of the offshore area of the Netherlands. The study area covers the Cleaverbank and Elbow Spit Platforms. Recently compiled maps and data are used to build the

Osmium Isotopic Evolution of the Mantle Sources of Precambrian Ultramafic Rocks

Science.gov (United States)

Gangopadhyay, A.; Walker, R. J.

2006-12-01

The Os isotopic composition of the modern mantle, as recorded collectively by ocean island basalts, mid- oceanic ridge basalts (MORB) and abyssal peridotites, is evidently highly heterogeneous (γ Os(I) ranging from +25). One important question, therefore, is how and when the Earth's mantle developed such large-scale Os isotopic heterogeneities. Previous Os isotopic studies of ancient ultramafic systems, including komatiites and picrites, have shown that the Os isotopic heterogeneity of the terrestrial mantle can be traced as far back as the late-Archean (~ 2.7-2.8 Ga). This observation is based on the initial Os isotopic ratios obtained for the mantle sources of some of the ancient ultramafic rocks determined through analyses of numerous Os-rich whole-rock and/or mineral samples. In some cases, the closed-system behavior of these ancient ultramafic rocks was demonstrated via the generation of isochrons of precise ages, consistent with those obtained from other radiogenic isotopic systems. Thus, a compilation of the published initial ^{187}Os/^{188}Os ratios reported for the mantle sources of komatiitic and picritic rocks is now possible that covers a large range of geologic time spanning from the Mesozoic (ca. 89 Ma Gorgona komatiites) to the Mid-Archean (e.g., ca. 3.3 Ga Commondale komatiites), which provides a comprehensive picture of the Os isotopic evolution of their mantle sources through geologic time. Several Precambrian komatiite/picrite systems are characterized by suprachondritic initial ^{187}Os/^{188}Os ratios (e.g., Belingwe, Kostomuksha, Pechenga). Such long-term enrichments in ^{187}Os of the mantle sources for these rocks may be explained via recycling of old mafic oceanic crust or incorporation of putative suprachondritic outer core materials entrained into their mantle sources. The relative importance of the two processes for some modern mantle-derived systems (e.g., Hawaiian picrites) is an issue of substantial debate. Importantly, however, the

A simple source preparation method for alpha-ray spectrometry of volcanic rock sample

International Nuclear Information System (INIS)

Takahashi, Masaomi; Kurihara, Yuichi; Sato, Jun

2006-01-01

A simple source preparation method was developed for the alpha-ray spectrometry to determine U and Th in volcanic rockes. Isolation of U and Th from volcanic rocks was made by use of UTEVA-Spec. resin, extraction chromatograph material. U and Th were extracted by TTA-benzene solution and organic phase was evaporated drop by drop on a hot stainless steel planchet to dryness. This method was found to be effective for the preparation of sources for alpha-ray spectrometry. (author)

Interpretation of Oil Seepage of Source Rock Based Magnetic Survey in Cipari Cilacap District

Directory of Open Access Journals (Sweden)

Sukmaji Anom Raharjo

2015-12-01

Full Text Available The magnetic survey had been conducted in Village of Cipari, District of Cipari, Region of  Cilacap to interpret to the location of the oil seepage source rock. Boundary of the research area is 108.75675°E – 108.77611°E and 7.42319°S – 7.43761°S. The observed total magnetic data is corrected and reducted to obtain the local magnetic anomaly data. The local magnetic anomaly data is applied to model the subsurface bodies anomalies based on the Mag2DC for Windows software. With be supported the geological information, the some bodies anomalies are interpreted as the basaltic igneous rock (c = 0.0051, the alternately of sandstone and claystone and insert of marl from Halang Formation (c = 0.0014, the breccia from Kumbang Formation (c = 0.0035, the alternately of sandstones and claystone with insert of marl and breccia from Halang Formation (c = 0.0036, the claystone from Tapak Formation (c = 0.0015, the alternately of sandstones and claystone with insert of marl and compacted breccia from Halang Formation (c = 0.0030, and the alternately of sandstone and claystone from   Halang Formation (c = 0.0020. The plantonic foraminifer fossils as resources of oil seepage are estimated in the sedimentaries rocks, where the oil flows from those rocks into the         reservoir (source rock. Based on the interpretation results, the source rock is above basaltic igneous rock with the approximate position is 108.76164°W and 7.43089°S; and the depth is 132.09 meters below the average topographic.

Thermal maturity history and implications for hydrocarbon exploration in the Catatumbo basin, Colombia

International Nuclear Information System (INIS)

Rangel, Antonio; Hernandez, Roberto

2007-01-01

A thermal model integrated with oil and gas geochemical study has been constructed for the Catatumbo basin, Colombia for provides petroleum system data for hydrocarbon exploration. The calibration of the thermal model with maturity data took into account a changing heat flow scheme which included a thermal increase towards the end of the Jurassic and another one in the early Eocene, associated with rifting events. Locally, active/generating source rocks are within the synclines axes. The hydrocarbon expulsion time for Cretaceous source rocks (Capacho and La Luna formations) started in the upper Paleocene-Eocene, while for the los Cuervos Formation the generation and expulsion started of 1 0 my. The petroleum expelled during the Paleocene-Miocene, were likely accumulated in structures formed since the end of the cretaceous, while the younger structures that resulted from the Andean orogen were charged by remigration from the older structures and additionally with the youngest lately generated hydrocarbons. The accumulations of hydrocarbons are mainly the result of generation and migration locally within the basin. The Catatumbo Basin contains thermogenic wet gases with different degrees of thermal maturity which varies from around 1,0 for 2,5 equivalent Ro. The highest degree of thermal evolution according to maturity indicators and thermal modeling is in the southern area, which is prospective for wet gas. The central and northern area appears more prospective for oil with minor amounts of gas

Mechanical study of the Chartreuse Fold-and-Thrust Belt: relationships between fluids overpressure and decollement within the Toarcian source-rock

Science.gov (United States)

Berthelon, Josselin; Sassi, William; Burov, Evgueni

2016-04-01

Many source-rocks are shale and constitute potential detachment levels in Fold-and-Thrust Belts (FTB): the toarcian Schistes-Cartons in the French Chartreuse FTB for example. Their mechanical properties can change during their burial and thermal maturation, as for example when large amount of hydrocarbon fluids are generated. A structural reconstruction of the Chartreuse FTB geo-history places the Toarcian Formation as the major decollement horizon. In this work, a mechanical analysis integrating the fluids overpressuring development is proposed to discuss on the validity of the structural interpretation. At first, an analogue of the Chartreuse Toarcian Fm, the albanian Posidonia Schist, is documented as it can provide insights on its initial properties and composition of its kerogen content. Laboratory characterisation documents the vertical evolution of the mineralogical, geochemical and mechanical parameters of this potential decollement layer. These physical parameters (i.e. Total Organic Carbon (TOC), porosity/permeability relationship, friction coefficient) are used to address overpressure buildup in the frontal part of the Chartreuse FTB with TEMISFlow Arctem Basin modelling approach (Faille et al, 2014) and the structural emplacement of the Chartreuse thrust units using the FLAMAR thermo-mechanical model (Burov et al, 2014). The hydro-mechanical modeling results highlight the calendar, distribution and magnitude of the overpressure that developed within the source-rock in the footwall of a simple fault-bend fold structure localized in the frontal part of the Chartreuse FTB. Several key geological conditions are required to create an overpressure able to fracture the shale-rocks and induce a significant change in the rheological behaviour: high TOC, low permeability, favourable structural evolution. These models highlight the importance of modeling the impact of a diffuse natural hydraulic fracturing to explain fluids propagation toward the foreland within

Reexamination of the source material of acid igneous rocks, based on the selected Sr isotopic data

International Nuclear Information System (INIS)

Kagami, Hiroo; Shuto, Kenji; Gorai, Masao

1975-01-01

The relation between the ages and the initial strontium isotopic compositions obtained from acid igneous rocks by the whole-rock isochron method is re-examined, on the basis of the selected data. The points based on the data having high values of standard deviation (on the isochrons) show considerable scattering. This is probably ascribed to admixture of sialic materials, or secondary alteration and other geologic causes. The points based on the data having lower values of standard deviation (sigma value: 0.0001 - 0.0019), on the other hand, are evidently plotted within a narrow region just above the presumed Sr evolutional region of the source material of oceanic tholeiites. It is noteworthy that the former region meets the latter region at an earlier stage of the evolutional history of the earth (about 40 x 10 8 yrs. ago or older). It may be conceivable that the former region is the Sr evolutional region of the source material of acid igneous rocks. Considering from the inclination of the above Sr evolutional region, the source material of most of acid igneous rocks may possibly be a certain basic material, chemically similar to the continental tholeiitic basalts or basaltic andesites. On the other hand, the source material of a few acid igneous rocks with low initial strontium isotopic ratios may be a certain basic material resembling the oceanic tholeiites. Another possibility is that these acid igneous rocks and oceanic tholeiites may have been formed, under different physical conditions, directly from a certain common source material presumably of peridotitic composition. (auth.)

Crustal contamination versus an enriched mantle source for intracontinental mafic rocks: Insights from early Paleozoic mafic rocks of the South China Block

Science.gov (United States)

Xu, Wenjing; Xu, Xisheng; Zeng, Gang

2017-08-01

Several recent studies have documented that the silicic rocks (SiO2 > 65 wt.%) comprising Silicic Large Igneous Provinces are derived from partial melting of the crust facilitated by underplating/intraplating of "hidden" large igneous province-scale basaltic magmas. The early Paleozoic intracontinental magmatic rocks in the South China Block (SCB) are dominantly granitoids, which cover a combined area of 22,000 km2. In contrast, exposures of mafic rocks total only 45 km2. These mafic rocks have extremely heterogeneous isotopic signatures that range from depleted to enriched (whole rock initial 87Sr/86Sr = 0.7041-0.7102; εNd(t) = - 8.4 to + 1.8; weighted mean zircon εHf(t) = - 7.4 to + 5.2), show low Ce/Pb and Nb/U ratios (0.59-13.1 and 3.5-20.9, respectively), and variable Th/La ratios (0.11-0.51). The high-MgO mafic rocks (MgO > 10 wt.%) tend to have lower εNd(t) values (- 4) and Sm/Nd ratios (> 0.255). The differences in geochemistry between the high-MgO and low-MgO mafic rocks indicate greater modification of the compositions of high-MgO mafic magmas by crustal material. In addition, generally good negative correlations between εNd(t) and initial 87Sr/86Sr ratios, MgO, and K2O, along with the presence of inherited zircons in some plutons, indicate that the geochemical and isotopic compositions of the mafic rocks reflect significant crustal contamination, rather than an enriched mantle source. The results show that high-MgO mafic rocks with fertile isotopic compositions may be indicative of crustal contamination in addition to an enriched mantle source, and it is more likely that the lithospheric mantle beneath the SCB during the early Paleozoic was moderately depleted than enriched by ancient subduction processes.

Chitin: 'Forgotten' Source of Nitrogen: From Modern Chitin to Thermally Mature Kerogen: Lessons from Nitrogen Isotope Ratios

Science.gov (United States)

Schimmelmann, A.; Wintsch, R.P.; Lewan, M.D.; DeNiro, M.J.

1998-01-01

Chitinous biomass represents a major pool of organic nitrogen in living biota and is likely to have contributed some of the fossil organic nitrogen in kerogen. We review the nitrogen isotope biogeochemistry of chitin and present preliminary results suggesting interaction between kerogen and ammonium during thermal maturation. Modern arthropod chitin may shift its nitrogen isotope ratio by a few per mil depending on the chemical method of chitin preparation, mostly because N-containing non-amino-sugar components in chemically complex chitin cannot be removed quantitatively. Acid hydrolysis of chemically complex chitin and subsequent ion-chromatographic purification of the "deacetylated chitin-monomer" D-glucosamine (in hydrochloride form) provides a chemically well-defined, pure amino-sugar substrate for reproducible, high-precision determination of ??15N values in chitin. ??15N values of chitin exhibited a variability of about one per mil within an individual's exoskeleton. The nitrogen isotope ratio differed between old and new exoskeletons by up to 4 per mil. A strong dietary influence on the ??15N value of chitin is indicated by the observation of increasing ??15N values of chitin from marine crustaceans with increasing trophic level. Partial biodegradation of exoskeletons does not significantly influence ??15N values of remaining, chemically preserved amino sugar in chitin. Diagenesis and increasing thermal maturity of sedimentary organic matter, including chitin-derived nitrogen-rich moieties, result in humic compounds much different from chitin and may significantly change bulk ??15N values. Hydrous pyrolysis of immature source rocks at 330??C in contact with 15N-enriched NH4Cl, under conditions of artificial oil generation, demonstrates the abiogenic incorporation of inorganic nitrogen into carbon-bound nitrogen in kerogen. Not all organic nitrogen in natural, thermally mature kerogen is therefore necessarily derived from original organic matter, but may

A comparison of geochemical features of extracts from coal-seams source rocks with different polarity solvents

Energy Technology Data Exchange (ETDEWEB)

Chen, Jianping; Deng, Chunping; Wang, Huitong

2009-02-15

There exists a great difference in group-type fractions and biomarker distributions of chloroform extracts from coals and coal-seams oils, which makes the source identification of coal-seams oils in sedimentary basins rather difficult. The experiment, in which four different polarity solvents, n-hexane, benzene, dichloromethane and chloroform, were used to extract 9 coal-seams source rocks and 3 typical lacustrine source rocks, showed that the yield of extracts increased gradually with increasing solvent polarity. The distribution features of their n-alkanes, isoprenoids and sterane and terpane biomarkers remained, in general, similar, showing no distinct enrichment or depletion for a certain fraction by any solvent. The compositional analysis on n-hexane and chloroform extracts showed that the absolute amount (concentration) of biomarkers was relatively low for the n-hexane extract but comparatively high for the chloroform extract, this difference became great among coal-seams source rocks but small among lacustrine mudstones. The statistical analysis on the relative amount of the 18 major biomarkers in n-hexane and chloroform extracts from 10 source rock samples showed that extracts with a proportional error for the same biomarker of less than 5% (including the analytical error) accounted for 84% while those with a proportional error over 10% amounted to below 5%. This suggested that the outcome of oil-source correlation made by these biomarkers will be independent of variations in amounts of saturates and biomarkers arising from solvent polarity. Therefore, biomarkers obtained from organic-rich source rocks including coals by the extraction with the commonly used chloroform solvent can be applied for the oilsource correlation of coal-seams petroliferous basins.

Factors controlling leaching of polycyclic aromatic hydrocarbons from petroleum source rock using nonionic surfactant

Energy Technology Data Exchange (ETDEWEB)

Akinlua, Akinsehinwa [Obafemi Awolowo Univ., Ile-Ife (Nigeria). Fossil Fuels and Environmental Geochemistry Group; Jochmann, Maik A.; Qian, Yuan; Schmidt, Torsten C. [Duisburg-Essen Univ., Essen (Germany). Instrumental Analytical Chemistry; Sulkowski, Martin [Duisburg-Essen Univ., Essen (Germany). Inst. of Environmental Analytical Chemistry

2012-03-15

The extraction of polycyclic aromatic hydrocarbons (PAHs) from petroleum source rock by nonionic surfactants with the assistance of microwave irradiation was investigated and the conditions for maximum yield were determined. The results showed that the extraction temperatures and type of surfactant have significant effects on extraction yields of PAHs. Factors such as surfactant concentration, irradiation power, sample/solvent ratio and mixing surfactants (i.e., mixture of surfactant at specific ratio) also influence the extraction efficiencies for these compounds. The optimum temperature for microwave-assisted nonionic surfactant extraction of PAHs from petroleum source rock was 120 C and the best suited surfactant was Brij 35. The new method showed extraction efficiencies comparable to those afforded by the Soxhlet extraction method, but a reduction of the extraction times and environmentally friendliness of the new nonionic surfactant extraction system are clear advantages. The results also show that microwave-assisted nonionic surfactant extraction is a good and efficient green analytical preparatory technique for geochemical evaluation of petroleum source rock. (orig.)

Thermal Maturity Data Used by the U.S. Geological Survey for the U.S. Gulf Coast Region Oil and Gas Assessment

Science.gov (United States)

Dennen, Kristin O.; Warwick, Peter D.; McDade, Elizabeth Chinn

2010-01-01

The U.S. Geological Survey is currently assessing the oil and natural gas resources of the U.S. Gulf of Mexico region using a total petroleum system approach. An essential part of this geologically based method is evaluating the effectiveness of potential source rocks in the petroleum system. The purpose of this report is to make available to the public RockEval and vitrinite reflectance data from more than 1,900 samples of Mesozoic and Tertiary rock core and coal samples in the Gulf of Mexico area in a format that facilitates inclusion into a geographic information system. These data provide parameters by which the thermal maturity, type, and richness of potential sources of oil and gas in this region can be evaluated.

Petroleum source-rock potentials of the cretaceous transgressive-regressive sedimentary sequences of the Cauvery Basin

Science.gov (United States)

Chandra, Kuldeep; Philip, P. C.; Sridharan, P.; Chopra, V. S.; Rao, Brahmaji; Saha, P. K.

The present work is an attempt to contribute to knowledge on the petroleum source-rock potentials of the marine claystones and shales of basins associated with passive continental margins where the source-rock developments are known to have been associated with the anoxic events in the Mesozoic era. Data on three key exploratory wells from three major depressions Ariyallur-Pondicherry, Thanjavur and Nagapattinam of the Cauvery Basin are described and discussed. The average total organic carbon contents of the transgressive Pre-Albian-Cinomanian and Coniacian/Santonian claystones/shales range from 1.44 and 1.16%, respectively. The transgressive/regressive Campanian/Maastrichtian claystones contain average total organic carbon varying from 0.62 to 1.19%. The kerogens in all the studied stratigraphic sequences are classified as type-III with Rock-Eval hydrogen indices varying from 30 to 275. The nearness of land masses to the depositional basin and the mainly clastic sedimentation resulted in accumulation and preservation of dominantly type-III kerogens. The Pre-Albian to Cinomanian sequences of peak transgressive zone deposited in deep marine environments have kerogens with a relatively greater proportion of type-II components with likely greater contribution of planktonic organic matters. The global anoxic event associated with the Albian-Cinomanian marine transgression, like in many other parts of the world, has pervaded the Cauvery Basin and favoured development of good source-rocks with type-III kerogens. The Coniacian-Campanian-Maastrichtian transgressive/regressive phase is identified to be relatively of lesser significance for development of good quality source-rocks.

Effects of Host-rock Fracturing on Elastic-deformation Source Models of Volcano Deflation.

Science.gov (United States)

Holohan, Eoghan P; Sudhaus, Henriette; Walter, Thomas R; Schöpfer, Martin P J; Walsh, John J

2017-09-08

Volcanoes commonly inflate or deflate during episodes of unrest or eruption. Continuum mechanics models that assume linear elastic deformation of the Earth's crust are routinely used to invert the observed ground motions. The source(s) of deformation in such models are generally interpreted in terms of magma bodies or pathways, and thus form a basis for hazard assessment and mitigation. Using discontinuum mechanics models, we show how host-rock fracturing (i.e. non-elastic deformation) during drainage of a magma body can progressively change the shape and depth of an elastic-deformation source. We argue that this effect explains the marked spatio-temporal changes in source model attributes inferred for the March-April 2007 eruption of Piton de la Fournaise volcano, La Reunion. We find that pronounced deflation-related host-rock fracturing can: (1) yield inclined source model geometries for a horizontal magma body; (2) cause significant upward migration of an elastic-deformation source, leading to underestimation of the true magma body depth and potentially to a misinterpretation of ascending magma; and (3) at least partly explain underestimation by elastic-deformation sources of changes in sub-surface magma volume.

Rock mechanics related to Jurassic underburden at Valdemar oil field

DEFF Research Database (Denmark)

Foged, Niels

1999-01-01

.It has been initiated as a feasibility study of the North Jens-1 core 12 taken in the top Jurassic clay shale as a test specimens for integrated petrological, mineralogical and rock mechanical studies. Following topics are studied:(1) Pore pressure generation due to conversion of organic matter...... and deformation properties of the clay shale using the actual core material or outcrop equivalents.(3) Flushing mechanisms for oil and gas from source rocks due to possibly very high pore water pressure creating unstable conditions in deeply burried sedimentsThere seems to be a need for integrating the knowledge...... in a number of geosciences to the benefit of common understanding of important reservoir mechanisms. Rock mechanics and geotechnical modelling might be key points for this understanding of reservoir geology and these may constitute a platform for future research in the maturing and migration from the Jurassic...

Qualitative and quantitative analysis of Dibenzofuran, Alkyldibenzofurans, and Benzo[b]naphthofurans in crude oils and source rock extracts

Science.gov (United States)

Meijun Li,; Ellis, Geoffrey S.

2015-01-01

Dibenzofuran (DBF), its alkylated homologues, and benzo[b]naphthofurans (BNFs) are common oxygen-heterocyclic aromatic compounds in crude oils and source rock extracts. A series of positional isomers of alkyldibenzofuran and benzo[b]naphthofuran were identified in mass chromatograms by comparison with internal standards and standard retention indices. The response factors of dibenzofuran in relation to internal standards were obtained by gas chromatography-mass spectrometry analyses of a set of mixed solutions with different concentration ratios. Perdeuterated dibenzofuran and dibenzothiophene are optimal internal standards for quantitative analyses of furan compounds in crude oils and source rock extracts. The average concentration of the total DBFs in oils derived from siliciclastic lacustrine rock extracts from the Beibuwan Basin, South China Sea, was 518 μg/g, which is about 5 times that observed in the oils from carbonate source rocks in the Tarim Basin, Northwest China. The BNFs occur ubiquitously in source rock extracts and related oils of various origins. The results of this work suggest that the relative abundance of benzo[b]naphthofuran isomers, that is, the benzo[b]naphtho[2,1-d]furan/{benzo[b]naphtho[2,1-d]furan + benzo[b]naphtho[1,2-d]furan} ratio, may be a potential molecular geochemical parameter to indicate oil migration pathways and distances.

Catalytic generation of methane at 60-100 °C and 0.1-300 MPa from source rocks containing kerogen Types I, II, and III

Science.gov (United States)

Wei, Lin; Schimmelmann, Arndt; Mastalerz, Maria; Lahann, Richard W.; Sauer, Peter E.; Drobniak, Agnieszka; Strąpoć, Dariusz; Mango, Frank D.

2018-06-01

Low temperature (60 and 100 °C) and long-term (6 months to 5 years) heating of pre-evacuated and sterilized shales and coals containing kerogen Types I (Mahogany Shale), II (Mowry Shale and New Albany Shale), and III (Springfield Coal and Wilcox Lignite) with low initial maturities (vitrinite reflectance Ro 0.39-0.62%) demonstrates that catalytically generated hydrocarbons may explain the occurrence of some non-biogenic natural gas accumulations where insufficient thermal maturity contradicts the conventional thermal cracking paradigm. Extrapolation of the observed rate of catalytic methanogenesis in the laboratory suggests that significant amounts of sedimentary organic carbon can be converted to relatively dry natural gas over tens of thousands of years in sedimentary basins at temperatures as low as 60 °C. Our laboratory experiments utilized source rock (shale and coal) chips sealed in gold and Pyrex® glass tubes in the presence of hydrogen-isotopically contrasting waters. Parallel heating experiments applied hydrostatic pressures from 0.1 to 300 MPa. Control experiments constrained the influence of pre-existing and residual methane in closed pores of rock chips that was unrelated to newly generated methane. This study's experimental methane yields at 60 and 100 °C are 5-11 orders of magnitude higher than the theoretically predicted yields from kinetic models of thermogenic methane generation, which strongly suggests a contribution of catalytic methanogenesis. Higher temperature, longer heating time, and lower hydrostatic pressure enhanced catalytic methanogenesis. No clear relationships were observed between kerogen type or total organic carbon content and methane yields via catalysis. Catalytic methanogenesis was strongest in Mowry Shale where methane yields at 60 °C amounted to ∼2.5 μmol per gram of organic carbon after one year of hydrous heating at ambient pressure. In stark contrast to the earlier findings of hydrogen isotopic exchange between

Bazhen Fm matured reservoir evaluation (West Siberia, Russia)

Science.gov (United States)

Parnachev, S.; Skripkin, A.; Baranov, V.; Zakharov, S.

2015-02-01

The depletion of the traditional sources of hydrocarbons leads to the situation when the biggest players of the oil and gas production market turn to unconventional reserves. Commercial shale oil and gas production levels in the USA have largely determined world prospects for oil and gas industry development. Russia takes one of the leading place in the world in terms of shale oil resources. The main source rock of the West Siberia, the biggest oil and gas basin in Russia under development, the Bazhen Fm and its stratigraphic and lithologic analogs, is located in the territory of over 1,000,000 square kilometers. Provided it has similar key properties (organic carbon content, porosity, permeability) with the deposits of the Bakken Fm and Green River Fm, USA, it is still extremely poorly described with laboratory methods. We have performed the laboratory analysis of core samples from a well drilled in Bazhen Fm deposits with matured organic matter (Tmax>435 °C). It was demonstrated the applicability of the improved steady-state gas flow method to evaluate the permeability of nanopermeable rocks. The role of natural fracturing in forming voids was determided that allows regarding potential Bazhen Fm reservoirs as systems with dual porosity and dual permeability.

Bazhen Fm matured reservoir evaluation (West Siberia, Russia)

International Nuclear Information System (INIS)

Parnachev, S; Skripkin, A; Baranov, V; Zakharov, S

2015-01-01

The depletion of the traditional sources of hydrocarbons leads to the situation when the biggest players of the oil and gas production market turn to unconventional reserves. Commercial shale oil and gas production levels in the USA have largely determined world prospects for oil and gas industry development. Russia takes one of the leading place in the world in terms of shale oil resources. The main source rock of the West Siberia, the biggest oil and gas basin in Russia under development, the Bazhen Fm and its stratigraphic and lithologic analogs, is located in the territory of over 1,000,000 square kilometers. Provided it has similar key properties (organic carbon content, porosity, permeability) with the deposits of the Bakken Fm and Green River Fm, USA, it is still extremely poorly described with laboratory methods. We have performed the laboratory analysis of core samples from a well drilled in Bazhen Fm deposits with matured organic matter (T max >435 °C). It was demonstrated the applicability of the improved steady-state gas flow method to evaluate the permeability of nanopermeable rocks. The role of natural fracturing in forming voids was determided that allows regarding potential Bazhen Fm reservoirs as systems with dual porosity and dual permeability

Transformation of juvenile Izu-Bonin-Mariana oceanic arc into mature continental crust: An example from the Neogene Izu collision zone granitoid plutons, Central Japan

Science.gov (United States)

Saito, Satoshi; Tani, Kenichiro

2017-04-01

Kaikomagatake granitoid pluton formed by anatexis of 'hybrid lower crust' consisting of K-rich rear-arc crust of the IBM arc and metasedimentary rocks of the Honshu arc. These studies collectively suggest that the chemical diversity within the Izu Collision Zone granitoid plutons reflects the chemical variation of basaltic sources (i.e., across-arc chemical variation in the IBM arc) as well as variable contribution of the metasedimentary component in the source region. The petrogenetic models of the Izu Collision Zone granitoid plutons suggest that collision with another mature arc/continent, hybrid lower crust formation and subsequent hybrid source anatexis are required for juvenile oceanic arcs to produce granitoid magmas with enriched compositions. The Izu Collision Zone granitoid plutons provide an exceptional example of the collision-induced transformation from a juvenile oceanic arc to the mature continental crust.

Neoproterozoic rift basins and their control on the development of hydrocarbon source rocks in the Tarim Basin, NW China

Science.gov (United States)

Zhu, Guang-You; Ren, Rong; Chen, Fei-Ran; Li, Ting-Ting; Chen, Yong-Quan

2017-12-01

The Proterozoic is demonstrated to be an important period for global petroleum systems. Few exploration breakthroughs, however, have been obtained on the system in the Tarim Basin, NW China. Outcrop, drilling, and seismic data are integrated in this paper to focus on the Neoproterozoic rift basins and related hydrocarbon source rocks in the Tarim Basin. The basin consists of Cryogenian to Ediacaran rifts showing a distribution of N-S differentiation. Compared to the Cryogenian basins, those of the Ediacaran are characterized by deposits in small thickness and wide distribution. Thus, the rifts have a typical dual structure, namely the Cryogenian rifting and Ediacaran depression phases that reveal distinct structural and sedimentary characteristics. The Cryogenian rifting basins are dominated by a series of grabens or half grabens, which have a wedge-shaped rapid filling structure. The basins evolved into Ediacaran depression when the rifting and magmatic activities diminished, and extensive overlapping sedimentation occurred. The distributions of the source rocks are controlled by the Neoproterozoic rifts as follows. The present outcrops lie mostly at the margins of the Cryogenian rifting basins where the rapid deposition dominates and the argillaceous rocks have low total organic carbon (TOC) contents; however, the source rocks with high TOC contents should develop in the center of the basins. The Ediacaran source rocks formed in deep water environment of the stable depressions evolving from the previous rifting basins, and are thus more widespread in the Tarim Basin. The confirmation of the Cryogenian to Ediacaran source rocks would open up a new field for the deep hydrocarbon exploration in the Tarim Basin.

The upper limit of maturity of natural gas generation and its implication for the Yacheng formation in the Qiongdongnan Basin, China

Science.gov (United States)

Su, Long; Zheng, Jianjing; Chen, Guojun; Zhang, Gongcheng; Guo, Jianming; Xu, Yongchang

2012-08-01

Vitrinite reflectance (VR, Ro%) measurements from residual kerogen of pyrolysis experiments were performed on immature Maoming Oil Shale substituted the samples for the gas-prone source rocks of Yacheng formation of the Qiongdongnan Basin in the South China Sea. The work was focused on determination an upper limit of maturity for gas generation (ULMGG) or "the deadline of natural gas generation". Ro values at given temperatures increase with increasing temperature and prolonged heating time, but ΔRo-value, given a definition of the difference of all values for VR related to higher temperature and adjacent lower temperature in open-system non-isothermal experiment at the heating rate of 20 °C/min, is better than VR. And representative examples are presented in this paper. It indicates that the range of natural gas generation for Ro in the main gas generation period is from 0.96% to 2.74%, in which ΔRo is in concordance with the stage for the onset and end of the main gas generation period corresponding to 0.02% up to 0.30% and from 0.30% up to 0.80%, respectively. After the main gas generation period of 0.96-2.74%, the evolution of VR approach to the ULMGG of the whole rock for type II kerogen. It is equal to 4.38% of VR, where the gas generation rates change little with the increase of maturation, ΔRo is the maximum of 0.83% corresponding to VR of 4.38%Ro, and the source rock does not nearly occur in the end process of hydrocarbon gas generation while Ro is over 4.38%. It shows that it is the same the ULMGG from the whole rock for type II kerogen as the method with both comparison and kinetics. By comparing to both the conclusions of pyrolysis experiments and the data of VR from the source rock of Yacheng formation on a series of selected eight wells in the shallow-water continental shelf area, it indicate that the most hydrocarbon source rock is still far from reaching ULMGG from the whole rock for type II kerogen. The source rock of Yacheng formation in the

Source rock identification of sediments using trace element ratios and 13C isotope data - a case study from Pondicherry region

International Nuclear Information System (INIS)

Tirumalesh, K.; Kulkarni, U.P.; Singh, Gursharan; Ramakumar, K.L.; Chidambaram, S.

2012-01-01

Compositional characteristics of source rocks are generally well recorded in sedimentary deposits and provide valuable information about nature of source rocks even though weathering, physical sorting and deposition environment influence the sediment geochemistry. In this paper we report major, trace element and 13 C isotope data of cutting samples collected from Quaternary, Tertiary and Cretaceous formations in Pondicherry area. The distribution patterns and inter elemental correlations are used to identify source rock composition and carbon isotope compositions to understand the sediment deposition conditions. Mineralogy of the bulk sediment indicates presence of Quartz, K-feldspar, Calcite, Mg-calcite, Aragonite and Clay minerals. Compared to upper continental crust values most of these sediments show lower concentration of all elements except Ca and Zn at some depths. The depletion is probably associated with weathering of feldspar and removal of elements through solution. This also increases the proportion of quartz relative to source rock. The ratios of redox sensitive elements (Th/U) infer oxic weathering in shallow sediments. Elemental ratios (La/Sc, Th/Sc, Th/Cr, Th/Co) and ternary plots (La-Th-Sc and Th-Hf-Co) indicate contribution of felsic source rocks with varying degree of weathering. These plots also infer the inherent heterogeneity in the source rocks. Hafnium correlations with other trace elements suggest contribution of Tonalitic rocks in addition to granite to these sediments. The geochemical characteristics of the sediments are found to be similar to that of sediments belonging to similar geology in nearby regions. Presence of shallow marine condition during the sedimentation is inferred from the detrital index (DI) values, which is further supported by the presence of fibrous clay minerals in ESEM scans. This study also brings out the utility of δ 13 C information to reinforce the geochemical and mineralogical inferences. (author)

Shear localization in a mature mylonitic rock analog during fast slip

Science.gov (United States)

Takahashi, M.; van den Ende, M. P. A.; Niemeijer, A. R.; Spiers, C. J.

2017-02-01

Highly localized slip zones developed within ductile shear zones, such as pseudotachylyte bands occurring within mylonitic fabric rocks, are frequently interpreted as evidence for earthquake nucleation and/or propagation within the ductile regime. To understand brittle/frictional shear localization processes in ductile shear zones and to relate these to earthquake nucleation and propagation, we performed tests with large changes in velocity on a brine-saturated, 80:20 (wt %) mixture of halite and muscovite gouge after forming a mature mylonitic structure through frictional-viscous flow. The direct effect a on shear strength that occurs in response to an instantaneous upward velocity-step is an important parameter in determining the nature of seismic rupture nucleation and propagation. We obtained reproducible results regarding low-velocity mechanical behavior compared with previous work, but also obtained new insights into effects of sudden increases in slip velocity on localization and strength evolution, at velocities above a critical velocity Vc (˜20 μm/s). We found that once a ductile, mylonitic structure has developed in a shear zone, subsequent cataclastic deformation is consistently localized in a narrow zone. This switch to localized deformation is controlled by the imposed velocity and becomes most apparent at velocities above Vc. In addition, the direct effect drops rapidly when the velocity exceeds Vc. This implies that slip can accelerate toward seismic velocities almost instantly and without much loss of fracture energy, once Vc is exceeded. Obtaining a measure for Vc in natural faults is therefore of key importance for understanding earthquake nucleation and propagation in the brittle-ductile transitional regime.

Phosphate-rich sedimentary rocks: significance for organic facies and petroleum exploration

Energy Technology Data Exchange (ETDEWEB)

Waples, D W

1982-03-01

Phosphorus-bearing rocks and sediments can be divided into two genetically distinct classes: phosphatic shales or limestones and phosphorites. Phosphatic shales are primary sediments in which phosphate nodules or micronodules have formed diagenetically by precipitation of calcium phosphates derived mainly from organic phosphorus. The nodules form in reducing environments at shallow depths within the sediments, where loss of phosphate by diffusion to the overlying water column is minimized. Highly biogenic sediments containing large amounts of organic matter and some fine clastic debris provide ideal environments for the formation of phosphate nodules. Phosphorites, in contrast, represent concentrated accumulations of reworked phosphate nodules which originated in phosphatic shales or limestones. Currents, wave action, recrystallization, and erosion and resedimentation are important mechanisms in the concentration process. Phosphatic shales and limestones may become excellent oil source rocks if thermal maturity is achieved. They are useful facies indicators for anoxic or nearly anoxic depositional environments, and are often associated with restricted basins, or, during certain geologic periods, with broad shelves developed during transgressions. Phosphorites, in contrast, are often correlated with sea-level regressions or uplifts. They are modest source rocks because of their low organic carbon contents and the fact that they were reworked under oxidizing conditions. Nevertheless, because phosphorites are derived from, and often grade into, phosphatic shales, they also are of potential utility in the search for oil source beds.

Research on supplying potential of uranium source from rocks in western provenance area of Hailaer basin

International Nuclear Information System (INIS)

Xia Yuliang; Liu Hanbin; Chinese Academy of Geological Sciences, Beijing

2006-01-01

Using U-Pb isotope composition evolution, this paper expounds the initial uranium content in volcanic rocks of provenance area of Xihulitu basin and in granites of provenance area of Kelulun sag, western Hailaer basin. The initial uranium content (U 0 ) in volcanic rocks of provenance area is higher, the average initial uranium content of volcanic rocks is 10.061 x 10 -6 , the average uranium variation coefficient (ΔU) is -49.57%; the average initial uranium content of granites is 18.381 x 10 -6 , the average uranium variation coefficient (ΔU) is -80%. The results indicate that rocks in provenance area could provide the pre-enrichment of uranium in deposited sandstone. U-Ra equilibrium coefficients of rocks indicate that there is obvious U-Ra disequilibrium phenomenon in volcanic rocks, and the time when granites provided uranium source occurred 16000 a ago. (authors)

Water sources for cyanobacteria below desert rocks in the Negev Desert determined by conductivity

OpenAIRE

McKay, Christopher P.

2016-01-01

We present year round meteorological and conductivity measurements of colonized hypolithic rocks in the Arava Valley, Negev Desert, Israel. The data indicate that while dew is common in the Negev it is not an important source of moisture for hypolithic organisms at this site. The dominance of cyanobacteria in the hypolithic community is consistent with predictions that cyanobacteria are confined to habitats supplied by rain. To monitor the presence of liquid water under the small Negev rocks ...

Characterization of coal-derived hydrocarbons and source-rock potential of coal beds, San Juan Basin, New Mexico and Colorado, U.S.A.

Science.gov (United States)

Rice, D.D.; Clayton, J.L.; Pawlewicz, M.J.

1989-01-01

.5 ppt), are chemically wetter (C1/C1-5 values range from 0.85 to 0.95), and contain less CO2 (< 2%). These gases are interpreted to have been derived from type III kerogen dispersed in marine shales of the underlying Lewis Shale and nonmarine shales of the Fruitland Formation. In the underlying Upper Cretaceous Dakota Sandstone and Tocito Sandstone Lentil of the Mancos Shale, another gas type is produced. This gas is associated with oil at intermediate stages of thermal maturity and is isotopically lighter and chemically wetter at the intermediate stage of thermal maturity as compared with gases derived from dispersed type III kerogen and coal; this gas type is interpreted to have been generated from type II kerogen. Organic matter contained in coal beds and carbonaceous shales of the Fruitland Formation has hydrogen indexes from Rock-Eval pyrolysis between 100 and 350, and atomic H:C ratios between 0.8 and 1.2. Oxygen indexes and atomic O:C values are less than 24 and 0.3, respectively. Extractable hydrocarbon yields are as high as 7,000 ppm. These values indicate that the coal beds and carbonaceous shales have good potential for the generation of liquid hydrocarbons. Voids in the coal filled with a fluorescent material that is probably bitumen is evidence that liquid hydrocarbon generation has taken place. Preliminary oil-source rock correlations based on gas chromatography and stable carbon isotope ratios of C15+ hydrocarbons indicate that the coals and (or) carbonaceous shales in the Fruitland Formation may be the source of minor amounts of condensate produced from the coal beds at relatively low levelsof thermal maturity (Rm=0.7). ?? 1989.

New insights on the maturity distribution and shale gas potential of the Lower Saxony Basin, NW-Germany

Energy Technology Data Exchange (ETDEWEB)

Bruns, B.; Littke, R. [RWTH Aachen Univ. (Germany). Energy and Mineral Resources Group (EMR); Di Primio, R. [Deutsches GeoForchungsZentrum (GFZ), Potsdam (Germany). Sektion 4.3 - Organische Geochemie; Berner, U. [Bundesanstalt fuer Geowissenschaften und Rohstoffe (BGR), Hannover (Germany)

2013-08-01

Due to its economic relevance the Lower Saxony Basin has been intensively investigated. Consequently it can be regarded as a well-known example of a sedimentary basin that experienced strong inversion. Oil and gas source rocks of economical importance comprise Upper Carboniferous coals as well as Jurassic (Toarcian/Posidonia Shale) and Cretaceous (Berriasian/Wealden) marls. Many basin modeling projects have addressed this area but until now the tectonic and maturation history as well as the petroleum system evolution has not been evaluated in a high-resolution 3D model. Therefore, a fully integrated 3D high-resolution numerical petroleum system model was developed incorporating the Lower Saxony Basin and major parts of the Pompeckj Block, and Muensterland Basin. The burial and maturation history has been reconstructed calibrated by large amounts of vitrinite reflectance and downhole temperature data enabling the output of erosion and maturity distribution maps of superior quality. (orig.)

Application of integrated vitrinite reflectance and FAMM analyses for thermal maturity assessment of the northeastern Malay Basin, offshore Vietnam: Implications for petroleum prospectivity evaluation

DEFF Research Database (Denmark)

Petersen, H. I.; Sherwood, N.; Mathiesen, A.

2008-01-01

Several exploration wells have intersected a Cenozoic coal-bearing, fluvial-deltaic mudstone and sandstone succession in the northeastern Vietnamese part of the Malay Basin, and have successfully tested seismically identified direct hydrocarbon indicators (DHIs). The oil and gas/condensate discov......Several exploration wells have intersected a Cenozoic coal-bearing, fluvial-deltaic mudstone and sandstone succession in the northeastern Vietnamese part of the Malay Basin, and have successfully tested seismically identified direct hydrocarbon indicators (DHIs). The oil and gas...... for the uppermost Oligocene source rocks between 2Ma and present-day, which post-dates trap formation. Seismic facies patterns suggest that lacustrine oil-prone units are in he oil window in the same graben complex a few km NW of the investigated well, and these rocks are likely to be the source of the hydrocarbons....../condensate discovery ell 46-CN-1x encountered a _55m thick section of lacustrine mudstones having considerable potential as an oil source. Vitrinite reflectance (VR) measurements from these alginite-bearing rocks introduce several problems in thermal maturity evaluation, including associated VR suppression...

Explosion Source Characteristics in Frozen and Unfrozen Rock

National Research Council Canada - National Science Library

Bonner, Jessie L; Leidig, Mark R; Murphy, Katherine; Dougherty, Sara L; Martin, Randolph J

2008-01-01

.... Central Alaska has abrupt lateral boundaries in discontinuous permafrost, and we detonated 3 shots in frozen, saturated rock and 3 shots nearby in unfrozen, dry rock ranging in size from 200 to 350 Ibs...

Stepwise Rock-Eval pyrolysis as a tool for typing heterogeneous organic matter in soils

Energy Technology Data Exchange (ETDEWEB)

Hetenyi, M.; Nyilas, T.; Toth, T.M. [Department of Mineralogy, Geochemistry and Petrology, University of Szeged, P.O. Box 651, H-6701 Szeged (Hungary)

2005-08-15

This paper presents an application of Rock-Eval pyrolysis for estimating the proportion of the components with different thermal stability in soil organic matter, the maturity of which corresponds to the early stage of diagenesis. For testing the validity of the modified Rock-Eval method, parallel series of pyrolysis were carried out on sedimentary rock samples. The temperature program was selected on the basis of the results obtained from stepwise Rock-Eval pyrolysis and from the mathematical deconvolution of pyrograms. The proportion of the original biomolecules in soil organic matter was calculated by the integration of pyrograms below 350{sup o}C and could be determined rapidly by one single pyrolysis using 350{sup o}C as initial cracking temperature. At 380{sup o}C, both the mathematical and the experimental methods provide reliable information about the proportion of the humic substances. Conversely, for rock samples, mathematical deconvolution of the pyrograms showed the heterogeneity of the sedimentary organic matter, the maturity of which corresponds to late diagenesis, without any estimation of the proportion of the different components. The rate of organic carbon accumulation in the studied soils and the decomposition rate of biopolymers were interpreted as a function of land-use and redox conditions. Differences in the precursor vegetation and in the environmental parameters resulted in markedly reduced carbon storage and higher degree of humification in the agricultural soil than in the adjacent forest soil. Redox conditions strongly affected both the amount and the elemental composition of the stored organic matter. The decomposition rate of biopolymers appeared to be controlled mainly by the contribution of resistant lignin components to the source biomass and, to a lesser extent, by redox conditions.

The strata and palaeo-geomorphology framework at the end of neoproterozoic and development mode of source rocks at the beginning of Cambrian in Tarim Basin, China

Directory of Open Access Journals (Sweden)

Xin Yang

2017-12-01

Full Text Available Referred to the new recognition from petroleum exploration of the Sinian to Cambrian in South China, it could be considered that the distribution of the early Cambrian source rocks was controlled by the palaeo-geomorphology at the end of Neoproterozoic in the Tarim Basin. Based on the zircon U-Pb dating of pyroclastic rock samples from the clastic rock stratum under the bottom of Cambrian carbonate rocks, the stratigraphic correlation of the Sinian to Cambrian was conducted to build the palaeo-geomorphology framework at the end of Neoproterozoic in Tarim Basin. Lastly, according to the development mode of source rocks at the beginning of Cambrian, the distribution of source rocks was predicted initially through the division of seismic facies. The youngest zircon concordia age of pyroclastic rocks from the bottom of well Tong 1 is 707±8Ma. It was revealed by the strata framework of the Sinian to Cambrian, the palaeo-geomorphology at the end of Neoproterozoic in Tarim Basin was characterized by an uplift highland in Bachu-Tazhong area, the south north high-low, and the west is higher than the east. The distribution of source rocks in the bottom of the Cambrian on the palaeo-platform and slopes was coincident with the Upper Sinian dolomite basically. But the contemporaneous sediment happened to be absent or changed in sedimentary facies on the uplift and its edges. From the seismic facies of the strata under the bottom of Cambrian, it could be concluded that source rocks in the type of the Xishanbraque Group (∈1xs was limited in the Manjiaer Depression, while the source rocks in the type of the Yuertusi Group (∈1y are widely distributed in south of Tabei Uplift, east Awat Depression, and even the Maigt Slope. However, among the west Awat Depression and western Tanguzibasi Depression, and the middle area of the Bachu-Tazhong Uplifts, the contemporaneous source rocks may have changed into sedimentary facies of tidal flat and lagoon, instead of

Organic-rich shales from internal Betic basins (SE Spain): potential source rocks analogs for the pre-Messinian Salt play in the western Mediterranean

Energy Technology Data Exchange (ETDEWEB)

Permanyer, A.; Jorge, R.; Baudino, R.; Gilbert, L.

2016-07-01

Southeastern Spain has a large number of Late Neogene basins with substantial evaporitic deposits that developed under an overall NNW-SSE compressional regime related to the African-European tectonic plates collision. Located in the Betic Cordillera, they can be considered as marginal Mediterranean basins that became gradually isolated during the Tortonian and Early Messinian due to tectonic uplift. Different evaporitic units accumulated in these basins during isolation and, in several cases, evaporitic conditions were associated to episodes of important organic matter accumulation. Results obtained from Late Tortonian to Early Messinian shales collected from boreholes, mines and outcrops in the internal Betic basins of Las Minas de Hellín, Cenajo and Socovos are presented. The organic matter was studied under fluorescence and scanning electron microscopy (SEM), and the main geochemical characteristics defined. They show a relation between organic-rich intervals with high potential of hydrocarbon generation, native sulfur, bio-induced dolomite and evaporitic deposits. These organicrich shales can be found before, during and after the evaporitic episodes. Results from the present study are compared with those previously obtained in the pre-evaporitic deposits of the Lorca Basin that showed high oil generation potential, a restricted-marine origin of the organic matter and a low degree of maturity. The occurrence of such potential source rocks in several basins points to a broad regional distribution. At a larger scale, in the Mediterranean Basin, organic-rich sediments were deposited before and during the Messinian Salinity Crisis. The studied examples could represent analogs for potential source rocks of the pre-Messinian salt play in the Western Mediterranean. (Author)

The Chinese Cretaceous Continental Scientific Drilling Project in the Songliao Basin, NE China: Organic-rich source rock evaluation with geophysical logs from Borehole SK-2

Science.gov (United States)

Zhang, X.; Zou, C.

2017-12-01

The Cretaceous strata have been recognized as an important target of oil or gas exploration in the Songliao Basin, northeast China. The second borehole (SK-2) of the Chinese Cretaceous Continental Scientific Drilling Project in the Songliao Basin (CCSD-SK) is the first one to drill through the Cretaceous continental strata in the frame of ICDP. It was designed not only to solve multiple scientific problems (including the Cretaceous paleoenvironment and paleoclimate, as well as deep resources exploration of the Songliao Basin), but also to expect to achieve new breakthroughs in oil and gas exploration. Based on the project, various geophysical log data (including gamma, sonic, resistivity, density etc.) and core samples have been collected from Borehole SK-2. We do research on organic-rich source rocks estimation using various geophysical log data. Firstly, we comprehensively analyzed organic-rich source rocks' geophysical log response characteristics. Then, source rock's identification methods were constructed to identify organic-rich source rocks with geophysical logs. The main identification methods include cross-plot, multiple overlap and Decision Tree method. Finally, the technique and the CARBOLOG method were applied to evaluate total organic carbon (TOC) content from geophysical logs which provide continuous vertical profile estimations (Passey, 1990; Carpentier et al., 1991). The results show that source rocks are widely distributed in Borehole SK-2, over a large depth strata (985 5700m), including Nenjiang, Qingshankou, Denglouku, Yingcheng, Shahezi Formations. The organic-rich source rocks with higher TOC content occur in the Qingshankou (1647 1650m), Denglouku (2534 2887m) and Shahezi (3367 5697m) Formations. The highest TOC content in these formations can reach 10.31%, 6.58%, 12.79% respectively. The bed thickness of organic-rich source rocks in the these formations are totally up to 7.88m, 74.34m, 276.60m respectively. These organic-rich rocks in the

Paleofacies of Eocene Lower Ngimbang Source Rocks in Cepu Area, East Java Basin based on Biomarkers and Carbon-13 Isotopes

Science.gov (United States)

Devi, Elok A.; Rachman, Faisal; Satyana, Awang H.; Fahrudin; Setyawan, Reddy

2018-02-01

The Eocene Lower Ngimbang carbonaceous shales are geochemically proven hydrocarbon source rocks in the East Java Basin. Sedimentary facies of source rock is important for the source evaluation that can be examined by using biomarkers and carbon-13 isotopes data. Furthermore, paleogeography of the source sedimentation can be reconstructed. The case study was conducted on rock samples of Lower Ngimbang from two exploration wells drilled in Cepu area, East Java Basin, Kujung-1 and Ngimbang-1 wells. The biomarker data include GC and GC-MS data of normal alkanes, isoprenoids, triterpanes, and steranes. Carbon-13 isotope data include saturate and aromatic fractions. Various crossplots of biomarker and carbon-13 isotope data of the Lower Ngimbang source samples from the two wells show that the source facies of Lower Ngimbang shales changed from transitional/deltaic setting at Kujung-1 well location to marginal marine setting at Ngimbang-1 well location. This reveals that the Eocene paleogeography of the Cepu area was composed of land area in the north and marine setting to the south. Biomarkers and carbon-13 isotopes are powerful data for reconstructing paleogeography and paleofacies. In the absence of fossils in some sedimentary facies, these geochemical data are good alternatives.

Organic Geochemistry and Rock-Eval Pyrolysis of Eocene fine Sediments, East Ketungau Basin, West Kalimantan

Directory of Open Access Journals (Sweden)

M.H. Hermiyanto Zajuli

2014-06-01

Full Text Available DOI: 10.17014/ijog.v6i2.119Indonesia contains many Paleogene and Neogene basins which some of them have been proven to be a very prolific producer of oil and gas. A study on the result of Rock-Eval pyrolysis and biomarker undertaken on the Eocene Mandai Group was able to assess hydrocarbon potential of the Paleogene fine sediments in the frontier basin, especially West Kalimantan area. East Ketungau Basin is located in the western Kalimantan, bounded with Melawi Basin by the Semitau High in the south and West Ketungau Basin in the west. The Mandai Group was deposited in the East Ketungau Basin during Eocene, consisting of sandstone and mudstone facies. Mudstone facies comprises shale, claystone, and coal. Seven samples of Eocene fine sediments collected from East Ketungau Basin were analyzed by Rock-Eval pyrolisis and three samples for biomarker to evaluate their hydrocarbon potential. The Rock-Eval pyrolisis result of Mandai Group shows that TOC value of this facies ranges from 0.34 % to 5.16 %, Potential Yield (PY between 0.06 and 4.78 mg HC/g rock, and Hydrogen Index (HI from 12 to 89. Based on that result, the fine sediments of Mandai Group are included into a gas prone source rock potential with poor to fair categories. Moreover Tmax values vary from 426o C to 451o C. The Eocene fine sediments of Mandai Group fall under kerogen type III. Based on Tmax and biomarker analyses, the maturity of the sediments is situated within immature to mature level. The fine sediments of Mandai Group were deposited in a terrestrial to marine environment under anoxic to sub-oxic condition.

Evolution of sulfur speciation in bitumen through hydrous pyrolysis induced thermal maturation of Jordanian Ghareb Formation oil shale

Science.gov (United States)

Birdwell, Justin E.; Lewan, Michael; Bake, Kyle D.; Bolin, Trudy B.; Craddock, Paul R.; Forsythe, Julia C.; Pomerantz, Andrew E.

2018-01-01

temperatures above 320 °C. This sulfur moiety ratio appears to provide complementary thermal maturity information to geochemical parameters derived from other analyses of extracted source rocks.

Biological denitrification from mature landfill leachate using a food-waste-derived carbon source.

Science.gov (United States)

Yan, Feng; Jiang, Jianguo; Zhang, Haowei; Liu, Nuo; Zou, Quan

2018-05-15

The mature landfill leachate containing high ammonia concentration (>1000 mg/L) is a serious threat to environment; however, the low COD to TN ratio (C/N, waste and oil-added food waste, were first applied as external carbon sources for the biological nitrogen removal from mature landfill leachate in an aerobic/anoxic membrane bioreactor. "Acidogenic liquid b" served quite better than commercial sodium acetate, considering the higher denitrification efficiency and the slightly rapider denitrification rate. The effect of C/N and temperature were investigated under hydraulic retention time (HRT) of 7 d, which showed that C/N ≥ 7 (25 °C) was enough to meet the general discharge standards of NH 4 + -N, TN and COD in China. Even for some special areas of China, the more stringent discharge standards (NH 4 + -N ≤ 8 mg/L, TN ≤ 20 mg/L) could also be achieved under longer HRT of 14 d and C/N ≥ 6. Notably, the COD concentration in effluent could also be well reduced to 50-55 mg/L, without further physical-chemical treatment. This proposed strategy, involving the high-value utilization of food waste, is thus promising for efficient nitrogen removal from mature landfill leachate. Copyright © 2018 Elsevier Ltd. All rights reserved.

Quantitative determination of minor and trace elements in rocks and soils by spark source mass spectrometry

International Nuclear Information System (INIS)

Ure, A.M.; Bacon, J.R.

1978-01-01

Experimental details are given of the quantitative determination of minor and trace elements in rocks and soils by spark source mass spectrometry. The effects of interfering species, and corrections that can be applied, are discussed. (U.K.)

Discovery and basic characteristics of high-quality source rocks found in the Yuertusi Formation of the Cambrian in Tarim Basin, China

Directory of Open Access Journals (Sweden)

Guangyou Zhu

2016-02-01

Full Text Available The Upper Paleozoic strata of the Tarim Basin have abundant resources of marine oil and gas. In the Tahe area, Halahatang area, and Tazhong area of the basin, many large-scale oilfields have been found. These oilfields have a confirmed oil and gas reserves worth more than 2.5 billion tons and have completed the annual output of more than 14 million tons of marine oil and gas equivalent. The belief that the only main hydrocarbon source rocks are of the Cambrian or Ordovician is still controversial. Chemists have made significant progress and have effectively lead the oil and gas exploration in Tarim Basin. Due to the complexity of the basin and the limitation of samples, the research work, and fine contrast is restricted. In this article, we investigated the Cambrian strata outcrop of Tarim Basin in detail. By analyzing a lot of outcrops, high-quality hydrocarbon source rocks of Yuertusi Formation have been found in more than 10 outcrop points in Aksu region. The source rocks' lithology is black shale with total organic carbon (TOC content that ranges between 2% and 16%. Total organic carbon (TOC of the black shale layer could be as much as 4%–16%, especially in the outcrops of the Yutixi and Shiairike. This by far is the best marine hydrocarbon source rock that was found in China. The source rocks were distributed consistently in the Aksu region, the thickness of which is about 10–15 m. It was formed in a sedimentary environment of a middle gentle slope to a low gentle slope. Organic matter enrichment is controlled by the upwelling currents. The thick strata of dolostone that developed in the Xiaoerblak Formation are considered to be good reservoirs of the beach and microbial reef in the upper strata of Yuertusi Formation. No hydrocarbon source rocks have been found in the outcrop of Xiaoerblak Formation. The thick strata of gyprock and mudstone development are a set of satisfactory cap layer in the Lower Cambrian. This hydrocarbon

Geophysical Prediction Technology Based on Organic Carbon Content in Source Rocks of the Huizhou Sag, the South China Sea

Directory of Open Access Journals (Sweden)

Yang Wei

2017-08-01

Full Text Available Due to the high exploration cost, limited number of wells for source rocks drilling and scarce test samples for the Total Organic Carbon Content (TOC in the Huizhou sag, the TOC prediction of source rocks in this area and the assessment of resource potentials of the basin are faced with great challenges. In the study of TOC prediction, predecessors usually adopted the logging assessment method, since the data is only confined to a “point” and the regional prediction of the source bed in the seismic profile largely depends on the recognition of seismic facies, making it difficult to quantify TOC. In this study, we combined source rock geological characteristics, logging and seismic response and built the mathematical relation between quasi TOC curve and seismic data based on the TOC logging date of a single well and its internal seismic attribute. The result suggested that it was not purely a linear relationship that was adhered to by predecessors, but was shown as a complicated non-linear relationship. Therefore, the neural network algorithm and SVMs were introduced to obtain the optimum relationship between the quasi TOC curve and the seismic attribute. Then the goal of TOC prediction can be realized with the method of seismic inversion.

Extraction of Iodine from Source Rock and Oil for Radioiodine Dating Final Report CRADA No. TC-1550-98

Energy Technology Data Exchange (ETDEWEB)

Moran, J. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Summa, L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-10-19

This was a collaborative effort between the University of California, Lawrence Livermore National Laboratory (LLNL) and Exxon Production Research Company (EPR) to develop improved techniques for extracting, concentrating, and measuring iodine from large volumes of source rock and oil. The purpose of this project was to develop a technique for measuring total iodine extracted from rock, obtain isotopic ratios, and develop age models for samples provided by EPR.

Thermal-maturity limit for primary thermogenic-gas generation from humic coals as determined by hydrous pyrolysis

Science.gov (United States)

Lewan, Michael; Kotarba, M.J.

2014-01-01

Hydrous-pyrolysis experiments at 360°C (680°F) for 72 h were conducted on 53 humic coals representing ranks from lignite through anthracite to determine the upper maturity limit for hydrocarbon-gas generation from their kerogen and associated bitumen (i.e., primary gas generation). These experimental conditions are below those needed for oil cracking to ensure that generated gas was not derived from the decomposition of expelled oil generated from some of the coals (i.e., secondary gas generation). Experimental results showed that generation of hydrocarbon gas ends before a vitrinite reflectance of 2.0%. This reflectance is equivalent to Rock-Eval maximum-yield temperature and hydrogen indices (HIs) of 555°C (1031°F) and 35 mg/g total organic carbon (TOC), respectively. At these maturity levels, essentially no soluble bitumen is present in the coals before or after hydrous pyrolysis. The equivalent kerogen atomic H/C ratio is 0.50 at the primary gas-generation limit and indicates that no alkyl moieties are remaining to source hydrocarbon gases. The convergence of atomic H/C ratios of type-II and -I kerogen to this same value at a reflectance of indicates that the primary gas-generation limits for humic coal and type-III kerogen also apply to oil-prone kerogen. Although gas generation from source rocks does not exceed vitrinite reflectance values greater than , trapped hydrocarbon gases can remain stable at higher reflectance values. Distinguishing trapped gas from generated gas in hydrous-pyrolysis experiments is readily determined by of the hydrocarbon gases when a -depleted water is used in the experiments. Water serves as a source of hydrogen in hydrous pyrolysis and, as a result, the use of -depleted water is reflected in the generated gases but not pre-existing trapped gases.

Impact of dia- and catagenesis on sulphur and oxygen sequestration of biomarkers as revealed by artificial maturation of an immature sedimentary rock

Science.gov (United States)

Koopmans, M.P.; De Leeuw, J. W.; Lewan, M.D.; Sinninghe, Damste J.S.

1996-01-01

Hydrous pyrolysis of an immature (R(a)??? 0.25%) sulphur-rich marl from the Gessoso-solfifera Formation (Messinian) in the Vena del Gesso Basin was carried out at 160C ??? T ???330 C for 72 h, to study the effect of progressive diagenesis and early catagenesis on the abundance and distribution of sulphur-containing and sulphur- and oxygen-linked carbon skeletons in low-molecular-weight and highmolecular-weight fractions (e.g. kerogen). To this end, compounds in the saturated hydrocarbon fraction, monoaromatic hydrocarbon fraction, polyaromatic hydrocarbon fraction, alkylsulphide fraction and ketone fraction were quantified, as well as compounds released after desulphurisation of the polar fraction and HI/LiAIH4 treatment of the desulphurised polar fraction. Sulphur-bound phytane and (20R)-5??,14??,17??(H) and (20R)-5??,14??,17??(H) C27 C29 steranes in the polar fraction become less abundant with increasing maturation temperature, whereas the amount of their corresponding hydrocarbons increases in the saturated hydrocarbon fraction. Carbon skeletons that are bound in the kerogen by multiple bonds (e.g. C38 n-alkane and isorenieratane) are first released into the polar fraction, and then as free hydrocarbons. These changes occur at relatively low levels of thermal maturity (R(a) <0.6%), as evidenced by the 'immature' values of biomarker maturity parameters such as the ????/(????+ ???? + ????) C35 hopane ratio and the 22S/(22S + 22R)-17??,21??(H) C35 hopane ratio. Sulphur- and oxygen-bound moieties, present in the polar fraction, are not stable with increasing thermal maturation. However, alkylthiophenes, ketones. 1,2-di-n-alkylbenzenes and free n-alkanes seem to be stable thermal degradation products of these sulphur- and oxygen-bound moieties. Thus, apart from free n-alkanes, which are abundantly present in more mature sedimentary rocks and crude oils, alkylthiophenes, 1,2-di-n-alkylbenzenes and ketones can also be expected to occur. The positions of the thiophene

Look! It's Rock'n'roll!

DEFF Research Database (Denmark)

Lindelof, Anja

2007-01-01

, and dates. Consult your library or click here for more information on citing sources. -------------------------------------------------------------------------------- Anja Mølle Lindelof. (2007). Look! it's rock'n'roll! how television participated in shaping the visual genre conventions of popular music...... to personal names, capitalization, and dates. Consult your library or click here for more information on citing sources. -------------------------------------------------------------------------------- Anja Mølle Lindelof. "Look! It's Rock'n'roll! How television participated in shaping the visual genre....... Pay special attention to personal names, capitalization, and dates. Consult your library or click here for more information on citing sources. -------------------------------------------------------------------------------- TY - JOUR T1 - Look! It's Rock'n'roll! How television participated in shaping...

Amorphous silica maturation in chemically weathered clastic sediments

Science.gov (United States)

Liesegang, Moritz; Milke, Ralf; Berthold, Christoph

2018-03-01

A detailed understanding of silica postdepositional transformation mechanisms is fundamental for its use as a palaeobiologic and palaeoenvironmental archive. Amorphous silica (opal-A) is an important biomineral, an alteration product of silicate rocks on the surface of Earth and Mars, and a precursor material for stable silica phases. During diagenesis, amorphous silica gradually and gradationally transforms to opal-CT, opal-C, and eventually quartz. Here we demonstrate the early-stage maturation of several million year old opal-A from deeply weathered Early Cretaceous and Ordovician sedimentary rocks of the Great Artesian Basin (central Australia). X-ray diffraction, scanning electron microscopy, and electron probe microanalyses show that the mineralogical maturation of the nanosphere material is decoupled from its chemical properties and begins significantly earlier than micromorphology suggests. Non-destructive and locally highly resolved X-ray microdiffraction (μ-XRD2) reveals an almost linear positive correlation between the main peak position (3.97 to 4.06 Å) and a new asymmetry parameter, AP. Heating experiments and calculated diffractograms indicate that nucleation and growth of tridymite-rich nanodomains induce systematic peak shifts and symmetry variations in diffraction patterns of morphologically juvenile opal-A. Our results show that the asymmetry parameter traces the early-stage maturation of amorphous silica, and that the mineralogical opal-A/CT stage extends to smaller d-spacings and larger FWHM values than previously suggested.

Rock-Eval 6 Applications in Hydrocarbon Exploration, Production, and Soil Contamination Studies Les applications de Rock-Eval 6 dans l'exploration et la production des hydrocarbures, et dans les études de contamination des sols

Directory of Open Access Journals (Sweden)

Lafargue E.

2006-12-01

Full Text Available Successful petroleum exploration relies on detailed analysis of the petroleum system in a given area. Identification of potential source rocks, their maturity and kinetic parameters, and their regional distribution are best accomplished by rapid screening of rock samples (cores and/or cuttings using the Rock-Eval apparatus. The technique has been routinely used for about fifteen years and has become a standard tool for hydrocarbon exploration. This paper describes how the new functions of the latest version of Rock-Eval (Rock-Eval 6 have expanded applications of the method in petroleum geoscience. Examples of new applications are illustrated for source rock characterization, reservoir geochemistry, and environmental studies, including quantification. Le succès d'une exploration pétrolière repose sur l'analyse détaillée du système pétrolier dans une zone donnée. L'identification des roches mères potentielles, la détermination de leur maturité, de leurs paramètres cinétiques et de leur répartition sont réalisées au mieux à partir d'examens rapides d'échantillons de roches (carottes ou déblais au moyen de la pyrolyse Rock-Eval. Cette technique a été utilisée en routine pendant une quinzaine d'années et elle est devenue un outil standard pour l'exploration des hydrocarbures. Cet article décrit comment les nouvelles fonctionnalités de la dernière version de l'appareil Rock-Eval (Rock-Eval 6 ont permis une expansion des applications de la méthode en géosciences pétrolières. Des exemples d'applications nouvelles sont illustrés dans les domaines de la caractérisation des roches mères, de la géochimie de réservoir et des études environnementales incluant la quantification et la description des hydrocarbures dans des sols contaminés.

Lead isotopes in archaean plutonic rocks

International Nuclear Information System (INIS)

Oversby, V.M.

1978-01-01

Archaean intrusive rocks have initial Pb isotopic compositions which show a varied and complex history for the source regions of the rocks. Even the oldest rocks from Greenland indicate heterogenous U and Pb distribution prior to 3800 m.y. ago. Source regions with μ values less than 7 must have played a significant role in the early history of the earth. By late Archaean time U/Pb ratios of source regions had increased substantially. Data from Australia and North America show distinct regional differences, both within and between continents. (Auth.)

Carbon and hydrogen isotopic variations of natural gases in the southeast Columbus basin offshore southeastern Trinidad, West Indies - clues to origin and maturity

International Nuclear Information System (INIS)

Norville, Giselle A.; Dawe, Richard A.

2007-01-01

Natural gas can have two distinct origins, biogenic and thermogenic sources. This paper investigates the types and maturities of natural gas present in the SE Columbus basin, offshore Trinidad. The chemical composition and the isotope ratios of C and H were determined for approximately 100 samples of natural gas from eight areas within the SE Columbus basin. These compositions and isotopic data are interpreted to identify the origins of gas (biogenic, thermogenic) and maturity. The data showed that the gases in the SE Columbus basin are of both biogenic and thermogenic origin with a trend of mainly thermogenic to mixed to biogenic when moving from SW to NE across the basin. This trend suggests differential burial of the source rock. The presence of mixed gas indicates there was migration of gas in the basin resulting in deeper thermogenic gas mixing with shallow biogenic gas

An analysis of natural gas exploration potential in the Qiongdongnan Basin by use of the theory of “joint control of source rocks and geothermal heat”

Directory of Open Access Journals (Sweden)

Zhang Gongcheng

2014-10-01

Full Text Available The Oligocene Yacheng Fm contains the most important source rocks that have been confirmed by exploratory wells in the Qiongdongnan Basin. The efficiency of these source rocks is the key to the breakthrough in natural gas exploration in the study area. This paper analyzes the hydrocarbon potential of each sag in this basin from the perspective of control of both source rocks and geothermal heat. Two types of source rocks occur in the Yacheng Fm, namely mudstone of transitional facies and mudstone of neritic facies. Both of them are dominated by a kerogen of type-III, followed by type-II. Their organic matter abundances are controlled by the amount of continental clastic input. The mudstone of transitional facies is commonly higher in organic matter abundance, while that of neritic facies is lower. The coal-measure source rocks of transitional facies were mainly formed in such environments as delta plains, coastal plains and barrier tidal flat-marshes. Due to the control of Cenozoic lithosphere extension and influence of neotectonism, the geothermal gradient, terrestrial heat flow value (HFV and level of thermal evolution are generally high in deep water. The hot setting not only determines the predominance of gas generation in the deep-water sags, but can promote the shallow-buried source rocks in shallow water into oil window to generate oil. In addition to promoting the hydrocarbon generation of source rocks, the high geothermal and high heat flow value can also speed up the cracking of residual hydrocarbons, thus enhancing hydrocarbon generation efficiency and capacity. According to the theory of joint control of source quality and geothermal heat on hydrocarbon generation, we comprehensively evaluate and rank the exploration potentials of major sags in the Qiongdongnan Basin. These sags are divided into 3 types, of which type-I sags including Yanan, Lingshui, Baodao, Ledong and Huaguang are the highest in hydrocarbon exploration potential.

Climate modeling - a tool for the assessment of the paleodistribution of source and reservoir rocks

Energy Technology Data Exchange (ETDEWEB)

Roscher, M.; Schneider, J.W. [Technische Univ. Bergakademie Freiberg (Germany). Inst. fuer Geologie; Berner, U. [Bundesanstalt fuer Geowissenschaften und Rohstoffe, Hannover (Germany). Referat Organische Geochemie/Kohlenwasserstoff-Forschung

2008-10-23

In an on-going project of BGR and TU Bergakademie Freiberg, numeric paleo-climate modeling is used as a tool for the assessment of the paleo-distribution of organic rich deposits as well as of reservoir rocks. This modeling approach is based on new ideas concerning the formation of the Pangea supercontinent. The new plate tectonic concept is supported by paleo- magnetic data as it fits the 95% confidence interval of published data. Six Permocarboniferous time slices (340, 320, 300, 290, 270, 255 Ma) were chosen within a first paleo-climate modeling approach as they represent the most important changes of the Late Paleozoic climate development. The digital maps have a resolution of 2.8 x 2.8 (T42), suitable for high-resolution climate modeling, using the PLASIM model. CO{sub 2} concentrations of the paleo-atmosphere and paleo-insolation values have been estimated by published methods. For the purpose of validation, quantitative model output, had to be transformed into qualitative parameters in order to be able to compare digital data with qualitative data of geologic indicators. The model output of surface temperatures and precipitation was therefore converted into climate zones. The reconstructed occurrences of geological indicators like aeolian sands, evaporites, reefs, coals, oil source rocks, tillites, phosphorites and cherts were then compared to the computed paleo-climate zones. Examples of the Permian Pangea show a very good agreement between model results and geological indicators. From the modeling approach we are able to identify climatic processes which lead to the deposition of hydrocarbon source and reservoir rocks. The regional assessment of such atmospheric processes may be used for the identification of the paleo-distribution of organic rich deposits or rock types suitable to form hydrocarbon reservoirs. (orig.)

Organic geochemical characterization of potential hydrocarbon source rocks in the upper Benue Trough

International Nuclear Information System (INIS)

Obaje, N. G.; Pearson, M. J.; Suh, C. E.; Dada, S. S.

1999-01-01

The Upper Benue Trough of Nigeria is the northeastern most portion of the Benue rift structure that extends from the northern limit of the Niger Delta in the south to the southern limit of the Chad basin int he northeast. this portion of the trough is made up of two arms: the Gongola Arm and the Yola Arm. Stratigraphic sequence in the Gongola Arm comprises the continental Albian Bima Sandstone, the transitional Cenomanian Yolde Formation and the marine Turonian - Santonian Gongila, Pindiga, and Fika Formations. Overlying these are the continental Campane - Maastrichtian Gombe Sandstone and the Tertiary Kerri - Kerri Formation. In the Yola Arm, the Turonian - Santonian sequence is replaced by the equally marine Dukul, Jessu, Sekuliye Formations, Numanha Shale, and the Lamja Sandstone. Organic geochemical studies have been carried on outcrop sample form the Gongila, Pindiga, Dukul Formations, the Fika shale and the shaly units of the Gombe Sandstone, with the aim of assessing their source rock potential. Gas Chromatography (GC), Gas Chromatography - Mass Spectrometry (C - MS), and Rock Eval Pyrolysis were the major organic geochemical tools employed. Biomaker hydrocarbon signatures obtained from the GC - MS and the Rock Eval Pyrolysis results indicate that all he formations studied, except the Dukul formation, are immature and are all lean in organic matter

Regional assessments of the hydrocarbon generation potential of selected North American proterozoic rock sequences. Progress report, September 1989--April 1990

Energy Technology Data Exchange (ETDEWEB)

Engel, M.H.; Elmore, R.D.

1990-04-01

Our primary research objectives for the first year of this grant are nearing completion. This includes comprehensive sedimentologic/organic geochemical studies of two depositionally distinct, unmetamorphosed units, the Nonesuch Formation ({approximately}1.1 Ga lacustrine rift deposit) and the Dripping Spring Quartzite ({approximately}1.3 Ga marine shelf deposit). As discussed in this progress report, an attempt has been made to (1) identify source rocks by quantification and characterization of constituent organic matter, (2) recognize depositional/diagenetic/catagenetic factors that may have influenced source rock quality and (3) evaluate the possibility of previous or current hydrocarbon generation and migration. Organic petrology and geochemical analyses suggest important differences between kerogens in the Michigan (MI) and Wisconsin (WI) Nonesuch Formation study areas. When considered within a geographic/stratigraphic framework, the Nonesuch Formation in the MI study area exhibits superior source rock potential. It is suggested that sedimentary organic matter in the WI area was subject to more extensive microbial alteration during early diagenesis. It is also possible that thermal maturity levels were slightly to moderately higher in WI than MI. Petrologic evidence for migrated bitumens and the stable isotope composition of late vein carbonates suggest, furthermore, that oil generation and migration may have actually been more extensive in the WI study area.

Evaluating Re-Os systematics in organic-rich sedimentary rocks in response to petroleum generation using hydrous pyrolysis experiments

Science.gov (United States)

Rooney, A.D.; Selby, D.; Lewan, M.D.; Lillis, P.G.; Houzay, J.-P.

2012-01-01

Successful application of the 187Re–187Os geochronometer has enabled the determination of accurate and precise depositional ages for organic-rich sedimentary rocks (ORS) as well as establishing timing constraints of petroleum generation. However, we do not fully understand the systematics and transfer behaviour of Re and Os between ORS and petroleum products (e.g., bitumen and oil). To more fully understand the behaviour of Re–Os systematics in both source rocks and petroleum products we apply hydrous pyrolysis to two immature hydrocarbon source rocks: the Permian Phosphoria Formation (TOC = 17.4%; Type II-S kerogen) and the Jurassic Staffin Formation (TOC = 2.5%; Type III kerogen). The laboratory-based hydrous pyrolysis experiments were carried out for 72 h at 250, 300, 325 and 350 °C. These experiments provided us with whole rock, extracted rock and bitumen and in some cases expelled oil and asphaltene for evaluation of Re–Os isotopic and elemental abundance. The data from these experiments demonstrate that the majority (>95%) of Re and Os are housed within extracted rock and that thermal maturation does not result in significant transfer of Re or Os from the extracted rock into organic phases. Based on existing thermodynamic data our findings suggest that organic chelating sites have a greater affinity for the quadravalent states of Re and Os than sulphides. Across the temperature range of the hydrous pyrolysis experiments both whole rock and extracted rock 187Re/188Os ratios show small variations (3.3% and 4.7%, for Staffin, respectively and 6.3% and 4.9% for Phosphoria, respectively). Similarly, the 187Os/188Os ratios show only minor variations for the Staffin and Phosphoria whole rock and extracted rock samples (0.6% and 1.4% and 1.3% and 2.2%). These isotopic data strongly suggest that crude oil generation through hydrous pyrolysis experiments does not disturb the Re–Os systematics in ORS as supported by various studies on natural systems. The

Characterization of source rocks and groundwater radioactivity at the Chihuahua valley

Energy Technology Data Exchange (ETDEWEB)

Renteria V, M.; Montero C, M.E.; Reyes C, M.; Herrera P, E.F.; Valenzuela H, M. [Centro de lnvestigacion en Materiales Avanzados, Miguel de Cervantes 120, 31109 Chihuahua, (Mexico); Rodriguez P, A. [World Wildlife Fund (WWF), Chihuahuan Desert Program, Coronado 1005, 31000 Chihuahua (Mexico); Manjon C, G.; Garcia T, R. [Universidad de Sevilla, Departamento de Fisica Aplicada 11, ETS Arquitectura, Av. Reina Mercedes 2, 41012 Sevilla, (Spain); Crespo, T. [Centro de Investigaciones Energeticas, Medioambientales y Tecnologicas (CIEMAT), Av. Complutense 22, 28040 Madrid, (Spain)]. e-mail: elena.montero@cimav.edu.mx

2007-07-01

As part of a scientific research project about alpha radioactivity in groundwater for human consumption at the Chihuahua City, the characterization of rock sources of radioactivity around de Chihuahua valley was developed. The radioactivity of groundwater and sediments was determined, too. The radioactivity of uranium- and thorium- series isotopes contained in rocks was obtained by high resolution gamma-ray spectroscopy. Some representative values are 50 Bq/kg for the mean value of Bi-214 activity, and 121.5 Bq/kg for the highest value at West of the city. The activity of sediments, extracted during wells perforation, was determined using a Nal(TI) detector. A non-reported before uranium ore was localized at the San Marcos range formation. Its outcrops are inside the Chihuahua-Sacramento valley basin and its activity characterization was performed. Unusually high specific uranium activities, determined by alpha spectrometry, were obtained in water, plants, sediments and fish extracted at locations close to outcrops of uranium minerals. The activity of water of the San Marcos dam reached 7.7 Bq/L. The activity of fish, trapped at San Marcos dam, is 0.99 Bq/kg. Conclusions about the contamination of groundwater at North of Chihuahua City were obtained. (Author)

Characterization of source rocks and groundwater radioactivity at the Chihuahua valley

International Nuclear Information System (INIS)

Renteria V, M.; Montero C, M.E.; Reyes C, M.; Herrera P, E.F.; Valenzuela H, M.; Rodriguez P, A.; Manjon C, G.; Garcia T, R.; Crespo, T.

2007-01-01

As part of a scientific research project about alpha radioactivity in groundwater for human consumption at the Chihuahua City, the characterization of rock sources of radioactivity around de Chihuahua valley was developed. The radioactivity of groundwater and sediments was determined, too. The radioactivity of uranium- and thorium- series isotopes contained in rocks was obtained by high resolution gamma-ray spectroscopy. Some representative values are 50 Bq/kg for the mean value of Bi-214 activity, and 121.5 Bq/kg for the highest value at West of the city. The activity of sediments, extracted during wells perforation, was determined using a Nal(TI) detector. A non-reported before uranium ore was localized at the San Marcos range formation. Its outcrops are inside the Chihuahua-Sacramento valley basin and its activity characterization was performed. Unusually high specific uranium activities, determined by alpha spectrometry, were obtained in water, plants, sediments and fish extracted at locations close to outcrops of uranium minerals. The activity of water of the San Marcos dam reached 7.7 Bq/L. The activity of fish, trapped at San Marcos dam, is 0.99 Bq/kg. Conclusions about the contamination of groundwater at North of Chihuahua City were obtained. (Author)

Potensi Batuan Induk Batu Serpih dan Batu Lempung di Daerah Watukumpul Pemalang Jawa Tengah

Directory of Open Access Journals (Sweden)

Sachrul Iswahyudi

2009-02-01

Full Text Available Shale and claystone of Watukumpul Area have capability to become the source rock of hydrocarbon because of the ability to conserve the organic material better. Potential of the rock become source rock is depend on its maturity and total organic carbon. This research test eight example of rock to analysis their total organic carbon (TOC and rock eval pyrolisis. Only one sample is claystone, while the seven others are shales. The analyses provide data of total organic carbon, hydrogen index, and vitrinite reflectances which was used to interpret source rock potential of research area. Through this research is known that the organic material content of shale and claystone of research area own the fair level of total organic carbon. Organic material is included Kerogen Type III with the origin of land organism or plant. These kerogens of research area prefer to produce gas or gas prone. Organic material or kerogens have reached the matured phase to generate hydrocarbon (mature level. Special follow the rock sample came from Location 8 which have over mature level. Its high maturity is suspect have relationship with the intrusion of diorite igneous rock in this research area. Further research is needed to investigate the relationship between diorite intrusion and organic material in this research area.

Genetic transformation of mature citrus plants.

Science.gov (United States)

Cervera, Magdalena; Juárez, José; Navarro, Luis; Peña, Leandro

2005-01-01

Most woody fruit species have long juvenile periods that drastically prolong the time required to analyze mature traits. Evaluation of characteristics related to fruits is a requisite to release any new variety into the market. Because of a decline in regenerative and transformation potential, genetic transformation procedures usually employ juvenile material as the source of plant tissue, therefore resulting in the production of juvenile plants. Direct transformation of mature material could ensure the production of adult transgenic plants, bypassing in this way the juvenile phase. Invigoration of the source adult material, establishment of adequate transformation and regeneration conditions, and acceleration of plant development through grafting allowed us to produce transgenic mature sweet orange trees flowering and bearing fruits in a short time period.

Isotope shifting capacity of rock

International Nuclear Information System (INIS)

Blattner, P.; Department of Scientific and Industrial Research, Lower Hutt

1980-01-01

Any oxygen isotope shifted rock volume exactly defines a past throughput of water. An expression is derived that relates the throughput of an open system to the isotope shift of reservoir rock and present-day output. The small isotope shift of Ngawha reservoir rock and the small, high delta oxygen-18 output are best accounted for by a magmatic water source

The feasibility and prospect of uranium-gas in black rock series of joint exploration and development

International Nuclear Information System (INIS)

Xu Guochang; Zhang Dehua; Zhang Hongjian

2014-01-01

By the analysis and contrast of existing form of gas-uranium, correlation between gas-uranium and organic matter, distribution characteristics and control factors of mineralization (bosom) in the sedimentary formation of shale gas and black uranium bearing rock series, the authors come to the conclusion that: in the carbonate-siliceous-pelitic of black rock series the uranium and gas (oil) is essentially equipped coenosarc of the same homology, syngenetic, reservoir. They are ore source beds of carbonate-siliceous-pelitic rock uranium deposit, and also the hydrocarbon source beds in which the shale gas form. In black shales, uranium largely exist in the form of the ion adsorption (acetyl ion/uranyl ion). Under fracturing conditions, we can realize desorption mode of chemical solvents of adding acid or alkali, and extract uranium by concentrating liquid (the same as in-situ mimng technology). Therefore, the fracturing technology (clear water fracturing techniques, repeat fracturing techniques, synchronization fracturing techniques, multistage fracturing techniques, network fracturing techniques and so on) of shale gas exploitation lay a foundation for black shale uranium-gas joint development. The mature and corollary use of fracturing techniques and in-situ mining technology of low grade uranium will undoubtedly further increase the industrial resource extent of uranium and gas, improve guaranteeing degree of resource, reform of promote energy production structure and provide a large number of economical and effective clean energy. (authors)

Performance evaluation of a natural treatment system for small communities, composed of a UASB reactor, maturation ponds (baffled and unbaffled) and a granular rock filter in series.

Science.gov (United States)

Dias, D F C; Passos, R G; Rodrigues, V A J; de Matos, M P; Santos, C R S; von Sperling, M

2018-02-01

Post-treatment of anaerobic reactor effluent with maturation ponds is a good option for small to medium-sized communities in tropical climates. The treatment line investigated, operating in Brazil, with an equivalent capacity to treat domestic sewage from 250 inhabitants, comprised a upflow anaerobic sludge blanket reactor followed by two shallow maturation ponds (unbaffled and baffled) and a granular rock filter (decreasing grain size) in series, requiring an area of only 1.5 m 2  inhabitant -1 . With an overall hydraulic retention time of only 6.7 days, the performance was excellent for a natural treatment system. Based on over two years of continuous monitoring, median removal efficiencies were: biochemical oxygen demand = 93%, chemical oxygen demand = 79%, total suspended solids = 87%, ammonia = 43% and Escherichia coli = 6.1 log units. The final effluent complied with European discharge standards and WHO guidelines for some forms of irrigation, and appeared to be a suitable alternative for treating domestic sewage for small communities in warm areas, especially in developing countries.

An experimental investigation of geochromatography during secondary migration of petroleum performed under subsurface conditions with a real rock

Directory of Open Access Journals (Sweden)

Larter Steve

2000-10-01

Full Text Available An understanding of the size of petroleum secondary migration systems is vital for successful exploration for petroleum reserves. Geochemists have suggested that compositional fractionation of petroleum accompanying the migration process (geochromatography can potentially be used to infer distances petroleum may have travelled and the ratio of oil in the reservoir to that lost in the carrier. To date, this has been attempted by measuring concentrations and distributions of specific steranes, and aromatic oxygen and nitrogen compounds in reservoired oils which have been proposed to respond to migration rather than to source maturity or other effects. We report here an experiment involving oil migration through an initially water wet siltstone under realistic subsurface carrier bed or reservoir conditions (48 MPa, 70°C where source facies and maturity effects are eliminated. We show that geochromatography does indeed occur even for initially water-saturated rocks and that the migration fractionations observed for alkylcarbazoles, benzocarbazoles and alkylphenols are very similar to those seen in field data sets. In contrast, sterane based migration parameters show no compositional fractionation under these conditions.

Dating and source determination of volcanic rocks from Khunik area (South of Birjand, South Khorasan using Rb-Sr and Sm-Nd isotopes

Directory of Open Access Journals (Sweden)

Somayeh Samiee

2016-12-01

Full Text Available The Khunik area is located in the south of Birjand, Khorasan province, in the eastern margin of Lut block. Tertiary volcanic rocks have andesite to trachy-andesite composition. Dating analyzing by Rb-Sr method on plagioclase and hornblende as well as whole-rock isochron method was performed on pyroxene-hornblende andesite rock unit. On this basis the emplacement age is Upper Paleocene (58±11 Ma. These rocks have initial 87Sr/86Sr and εNd 0.7046-0.7049 and 2.16-3.12, respectively. According to isotopic data, volcanic rocks originated from depleted mantle and have the least crust contamination while it was fractionated. Geochemically, Khunik volcanic rocks have features typical of calk-alkaline to shoshonite and are metaluminous. Enrichment in LILEs and typical negative anomalies of Nb and Ti are evidences that the volcanic rocks formed in a subduction zone and active continental margin. Modeling suggests that these rocks were derived dominantly from 1–5% partial melting of a mainly spinel garnet lherzolite mantle source that is metasomatized by slab-derived fluid.

Conditions promoting and restraining agronomic effectiveness of water-insoluble phosphate sources, in particular phosphate rock (PR): I. Indices of phosphate rock use opportunity (PRUOIS) and of phosphate rock suitability for direct use (PRSIDU)

International Nuclear Information System (INIS)

Borlan, Z.; Gavriluta, I.; Soare, M.; Stefanescu, D.; Alexandrescu, A.

2002-01-01

Several issues of phosphate rock (PR) use are discussed in this paper. Maize for green fodder (Zea mays L) and ryegrass (Lolium multiflorum Lam.) were grown in 7 kg of dry soil and in small pots of 1.25 kg dry soil capacity, respectively, on several base unsaturated soils belonging to Hapludoll and Hapludalf soil groups. The amount of phosphate rock (PR) to apply was based on experimental data considering soil adsorbed acidity (Ah), humus content (H 2 ), cation exchange capacity (T), sum of exchangeable bases (SEB) and mobile (easily soluble) phosphate content (P A L) in the soil. The factors were combined in a rock phosphate use, opportunity index of the soil (PRUOIS): PRUOIS=(A h *H 2 *100)/SEB*10 0.0245*P AL Rock phosphate suitability for direct use was evaluated by means of the rate of PR-P dissolution (PRPRS) in a 0.6% ammonium heptamolybdate in 0.01M calcium chloride solution (ppm P) and by carbonate content (%CaCO 3 ) in PR. Both of these parameters combined provided a phosphate rock suitability index for direct use (PRSIDU): PRSIDU [ppmP/min]=PRPRS*(1-0.03*CaCO 3 ) Water insoluble P sources studied were PR from Kola-Russia, Morocco, Kneifiss-Siria, El Hassa-Jordan, Gafsa- Tunisia, North-Carolina (USA), and Arad-Israel. All PRs were compared with TSP applied at the same rate of P. Neither PRUOIS or PRSIDU considered separately could satisfactorily explain the variance of PR efficiency. An index obtained by multiplicative combination of PRUOIS x PRSIDU did correlate significantly with indices on the agronomic efficiency of PR. (author)

Thermal maturity and petroleum kitchen areas of Liassic Black Shales (Lower Jurassic) in the central Upper Rhine Graben, Germany

Science.gov (United States)

Böcker, Johannes; Littke, Ralf

2016-03-01

In the central Upper Rhine Graben (URG), several major oil fields have been sourced by Liassic Black Shales. In particular, the Posidonia Shale (Lias ɛ, Lower Toarcian) acts as excellent and most prominent source rock in the central URG. This study is the first comprehensive synthesis of Liassic maturity data in the URG area and SW Germany. The thermal maturity of the Liassic Black Shales has been analysed by vitrinite reflectance (VRr) measurements, which have been verified with T max and spore coloration index (SCI) data. In outcrops and shallow wells (oil window (ca. 0.50-0.60 % VRr). This maturity is found in Liassic outcrops and shallow wells in the entire URG area and surrounding Swabian Jura Mountains. Maximum temperatures of the Posidonia Shale before graben formation are in the order of 80-90 °C. These values were likely reached during Late Cretaceous times due to significant Upper Jurassic and minor Cretaceous deposition and influenced by higher heat flows of the beginning rift event at about 70 Ma. In this regard, the consistent regional maturity data (VRr, T max, SCI) of 0.5-0.6 % VRr for the Posidonia Shale close to surface suggest a major burial-controlled maturation before graben formation. These consistent maturity data for Liassic outcrops and shallow wells imply no significant oil generation and expulsion from the Posidonia Shale before formation of the URG. A detailed VRr map has been created using VRr values of 31 wells and outcrops with a structure map of the Posidonia Shale as reference map for a depth-dependent gridding operation. Highest maturity levels occur in the area of the Rastatt Trough (ca. 1.5 % VRr) and along the graben axis with partly very high VRr gradients (e.g. well Scheibenhardt 2). In these deep graben areas, the maximum temperatures which were reached during upper Oligocene to Miocene times greatly exceed those during the Cretaceous.

Unzen volcanic rocks as heat source of geothermal activity

Energy Technology Data Exchange (ETDEWEB)

Hayashi, Masao; Sugiyama, Hiromi

1987-03-25

Only a few radiometric ages have been reported so far for the Unzen volcanic rocks. In this connection, in order to clarify the relation between volcanism and geothermal activity, fission track ages of zircon seperated from the Unzen volcanic rocks in western Kyushu have been dated. Since all the rocks are thought to be young, the external surface re-etch method was adopted. The results are that the age and standard error of the basal volcaniclastic rocks of the Tatsuishi formation are 0.28 +- 0.05 Ma and 0.25 +- 0.05 Ma. The next oldest Takadake lavas range from 0.26 to 0.20 Ma. The Kusenbudake lavas fall in a narrow range from 0.19 to 0.17 Ma. The latest Fugendake lavas are younger than 0.07 Ma.In conclusion, the most promising site for geothermal power generation is the Unzen hot spring field because of its very high temperature. After that, comes the Obama hot spring field because of the considerable high temperature chemically estimated. In addition, the northwestern area of the Unzen volcanic region will be promising for electric power generation in spite of no geothermal manifestations, since its volcanos are younger than 0.2 Ma. (14 figs, 14 tabs, 22 refs)

Oil geochemistry of the Putumayo basin

International Nuclear Information System (INIS)

Ramon, J.C

1996-01-01

Bio marker fingerprinting of 2O crude oils from Putumayo Basin, Colombia, shows a vertical segregation of oil families. The Lower Cretaceous reservoirs (Caballos and 'U' Villeta sands) contain oils that come from a mixture of marine and terrestrial organic matter, deposited in a marginal, 'oxic' marine setting. The Upper Cretaceous ('T' and N ' sands) and Tertiary reservoirs contain oils with marine algal input deposited in a reducing, carbonate-rich environment. Lithology, environmental conditions and organic matter type of source rocks as predicted from oil bio marker differences correspond to organic composition of two Cretaceous source rocks. Vertical heterogeneity in the oils, even those from single wells, suggests the presence of two isolated petroleum systems. Hydrocarbons from Lower Cretaceous source rocks charged Lower Cretaceous reservoirs whereas oils from Upper Cretaceous source rocks charged Upper Cretaceous and Tertiary reservoirs. Oil migration from mature source rocks into multiple reservoirs has been stratigraphically up dip along the regional sandstone units and vertical migration through faults has been limited. Bio marker maturity parameters indicate that all oils were generated from early thermal maturity oil window

Molecular isotopic characterisation of hydrocarbon biomarkers in Palaeocene-Eocene evaporitic, lacustrine source rocks from the Jianghan Basin, China

NARCIS (Netherlands)

Sinninghe Damsté, J.S.; Grice, Kliti; Schouten, S.; Peters, Kenneth E.

1998-01-01

Immature organic matter in lacustrine source rocks from the Jianghan Basin, eastern China, was studied for distributions and stable carbon isotopic compositions (13C) of hydrocarbon biomarkers. All of the bitumens contain isorenieratane (13C ca. −17 ) indicating the presence of Chlorobiaceae, and

Combined stable isotope trajectories for water-rock interaction

International Nuclear Information System (INIS)

Blattner, P.; Department of Scientific and Industrial Research, Lower Hutt

1981-01-01

The 'mixed' model of water-rock interaction (1980 Workshop) is explained in detail. Based on the magnitude of the oxygen isotope shifts of their recharge water, different geothermal systems can be placed in an evolutionary series, from incipient (large shift of water) to mature (small shift of water). Isotopes of different chemical elements may be combined, to yield a stringent test of whether or not a given change in rock composition may be ascribed to interaction with water (L-shaped trajectories). For the acidic eruptives of the Taupo Volcanic Zone, available strontium and oxygen isotope data practically rule out an origin by partial melting of greywacke basement

REE enrichment in granite-derived regolith deposits of the southeast United States: Prospective source rocks and accumulation processes

Science.gov (United States)

Foley, Nora K.; Ayuso, Robert A.; Simandl, G.J.; Neetz, M.

2015-01-01

The Southeastern United States contains numerous anorogenic, or A-type, granites, which constitute promising source rocks for REE-enriched ion adsorption clay deposits due to their inherently high concentrations of REE. These granites have undergone a long history of chemical weathering, resulting in thick granite-derived regoliths, akin to those of South China, which supply virtually all heavy REE and Y, and a significant portion of light REE to global markets. Detailed comparisons of granite regolith profiles formed on the Stewartsville and Striped Rock plutons, and the Robertson River batholith (Virginia) indicate that REE are mobile and can attain grades comparable to those of deposits currently mined in China. A REE-enriched parent, either A-type or I-type (highly fractionated igneous type) granite, is thought to be critical for generating the high concentrations of REE in regolith profiles. One prominent feature we recognize in many granites and mineralized regoliths is the tetrad behaviour displayed in REE chondrite-normalized patterns. Tetrad patterns in granite and regolith result from processes that promote the redistribution, enrichment, and fractionation of REE, such as late- to post- magmatic alteration of granite and silicate hydrolysis in the regolith. Thus, REE patterns showing tetrad effects may be a key for discriminating highly prospective source rocks and regoliths with potential for REE ion adsorption clay deposits.

Organic petrology and geochemistry of Eocene Suzak bituminous marl, north-central Afghanistan: Depositional environment and source rock potential

Science.gov (United States)

Hackley, Paul C.; Sanfilipo, John

2016-01-01

Organic geochemistry and petrology of Eocene Suzak bituminous marl outcrop samples from Madr village in north-central Afghanistan were characterized via an integrated analytical approach to evaluate depositional environment and source rock potential. Multiple proxies suggest the organic-rich (TOC ∼6 wt.%) bituminous marls are ‘immature’ for oil generation (e.g., vitrinite Ro  1) indicating organic input from marine algae and/or bacterial biomass, and sterane/hopane ratios are low (0.12–0.14). Monoaromatic steroids are dominated by C28clearly indicating a marine setting. High gammacerane index values (∼0.9) are consistent with anoxia stratification and may indicate intermittent saline-hypersaline conditions. Stable C isotope ratios also suggest a marine depositional scenario for the Suzak samples, consistent with the presence of marine foraminifera including abundant planktic globigerinida(?) and rare benthic discocyclina(?) and nummulites(?). Biomarker 2α-methylhopane for photosynthetic cyanobacteria implies shallow photic zone deposition of Madr marls and 3β-methylhopane indicates presence of methanotrophic archaea in the microbial consortium. The data presented herein are consistent with deposition of Suzak bituminous marls in shallow stratified waters of a restricted marine basin associated with the southeastern incipient or proto-Paratethys. Geochemical proxies from Suzak rock extracts (S content, high polar content, C isotopes, normal (αααR) C27–29 steranes, and C29/C30 and C26/C25 hopane ratios) are similar to extant data from Paleogene oils produced to the north in the Afghan-Tajik Basin. This observation may indicate laterally equivalent strata are effective source rocks as suggested by previous workers; however, further work is needed to strengthen oil-source correlations.

2D seismic interpretation and characterization of the Hauterivian-Early Barremian source rock in Al Baraka oil field, Komombo Basin, Upper Egypt

Science.gov (United States)

Ali, Moamen; Darwish, M.; Essa, Mahmoud A.; Abdelhady, A.

2018-03-01

Komombo Basin is located in Upper Egypt about 570 km southeast of Cairo; it is an asymmetrical half graben and the first oil producing basin in Upper Egypt. The Six Hills Formation is of Early Cretaceous age and subdivided into seven members from base to top (A-G); meanwhile the B member is of Hauterivian-Early Barremian and it is the only source rock of Komombo Basin. Therefore, a detailed study of the SR should be carried out, which includes the determination of the main structural elements, thickness, facies distribution and characterization of the B member SR which has not been conducted previously in the study area. Twenty 2D seismic lines were interpreted with three vertical seismic profiles (VSP) to construct the depth structure-tectonic map on the top of the B member and to highlight the major structural elements. The interpretation of depth structure contour map shows two main fault trends directed towards the NW-SE and NE to ENE directions. The NW-SE trend is the dominant one, creating a major half-graben system. Also the depth values range from -8400 ft at the depocenter in the eastern part to -4800 ft at the shoulder of the basin in the northwestern part of the study area. Meanwhile the Isopach contour map of the B member shows a variable thickness ranging between 300 ft to 750 ft. The facies model shows that the B member SR is composed mainly of shale with some sandstone streaks. The B member rock samples were collected from Al Baraka-1 and Al Baraka SE-1 in the eastern part of Komombo Basin. The results indicate that the organic matter content (TOC) has mainly good to very good (1-3.36 wt %), The B member samples have HI values in the range 157-365 (mg HC/g TOC) and dominated by Type II/III kerogen, and is thus considered to be oil-gas prone based on Rock-Eval pyrolysis, Tmax values between 442° and 456° C therefore interpreted to be mature for hydrocarbon generation. Based on the measured vitrinite equivalent reflectance values, the B member SR

Sedimentary organic matter sources, benthic consumption and burial in west Spitsbergen fjords - Signs of maturing of Arctic fjordic systems?

Science.gov (United States)

Zaborska, Agata; Włodarska-Kowalczuk, Maria; Legeżyńska, Joanna; Jankowska, Emilia; Winogradow, Aleksandra; Deja, Kajetan

2018-04-01

Mature ecosystems sequester little organic carbon (Corg) in sediments, as the complex and effective food webs consume most available organic matter within the water column and sediment, in contrast to young systems, where a large proportion of Corg is buried in deeper sediment layers. In this paper we hypothesize that "warmer" Atlantic water influenced fjord exhibits the 'mature' system features as compared to "cooler" Arctic water influenced fjord. Corg concentrations, sources and burial rates, as well as macrobenthic community standing stocks, taxonomic and functional composition and carbon demand, were compared in two west Spitsbergen fjords that are to different extents influenced by Atlantic water and can be treated as representing a cold one (Hornsund) and a warm one (Kongsfjorden). Water, sediments and macrofauna were collected at three stations in the central basin of each fjord. Corg, Ntot, δ13Corg and δ15N were measured in suspended matter, sediment cores and possible organic matter sources. The composition of sources of sedimentary organic matter was modeled by Mix-SIAR Bayesian stable isotope mixing models. The 210Pb method was used to calculate sediment accumulation rates, Corg accumulation and burial rates. The sedimentary Corg concentration and accumulation rate were larger in Hornsund than in Kongsfjorden. The contributions of pelagic sources to the Corg in sediments were similar in both fjords, macroalgal detritus had a higher importance in Kongsfjorden, while terrestrial sources were more important in Hornsund. Similar density and species richness were noted in both fjords, but higher biomass, individual biomass, production and carbon demand of benthic communities were noted in Kongsfjorden despite the lower amounts of Corg in sediments, indicating that macrobenthos responds to quality rather than quantity of available food. Subsurface tube-building conveyer belt detritus feeders (maldanids and oweniids) were responsible for higher standing

Effects of explosions in hard rocks

International Nuclear Information System (INIS)

Heuze, F.E.; Walton, O.R.; Maddix, D.M.; Shaffer, R.J.; Butkovich, T.R.

1993-01-01

This work relates to explosions in hard rocks (ex: basalt, granite, limestone...). Hard rock masses typically have a blocky structure created by the existence of geologic discontinuities such as bedding contacts, faults, and joints. At very high pressure - hundreds of kilobars and above - these discontinuities do not act separately, and the rock appears to be an equivalent continuous medium. At stress of a few tens of kilobars and below, the geologic discontinuities control the kinematics of the rock masses. Hence, the simulation of rock dynamics, anywhere but in the very-near source region, should account for those kinematics

Mass Dependent Fractionation of Hg Isotopes in Source Rocks, Mineral Deposits and Spring Waters of the California Coast Ranges, USA

Science.gov (United States)

Smith, C. N.; Kesler, S. E.; Blum, J. D.; Rytuba, J. J.

2007-12-01

We present here the first study of the isotopic composition of Hg in rocks, ore deposits, and active hydrothermal systems from the California Coast Ranges, one of Earth's largest Hg-depositing systems. The Franciscan Complex and Great Valley Sequence, which form the bedrock in the California Coast Ranges, are intruded and overlain by Tertiary volcanic rocks including the Clear Lake Volcanic Sequence. These rocks contain two types of Hg deposits, hot-spring deposits that form at shallow depths (<300 m) and silica-carbonate deposits that extend to greater depths (200 to 1000 m), as well as active springs and geothermal systems that release Hg to the present surface. The Franciscan Complex and Great Valley Sequence contain clastic sedimentary rocks with higher concentrations of Hg than volcanic rocks of the Clear Lake Volcanic Field. Mean Hg isotope compositions for all three rock units are similar, although the range of values in Franciscan Complex rocks is greater than in either Great Valley or Clear Lake rocks. Hot spring and silica-carbonate Hg deposits have similar average isotopic compositions that are indistinguishable from averages for the three rock units, although δ202Hg values for the Hg deposits have a greater variance than the country rocks. Precipitates from dilute spring and saline thermal waters in the area have similarly large variance and a mean δ202Hg value that is significantly lower than the ore deposits and rocks. These observations indicate there is little or no isotopic fractionation during release of Hg from its source rocks into hydrothermal solutions. Isotopic fractionation does appear to take place during transport and concentration of Hg in deposits, especially in their uppermost parts. Boiling of hydrothermal fluids is likely the most important process causing of the observed Hg isotope fractionation. This should result in the release of Hg with low δ202Hg values into the atmosphere from the top of these hydrothermal systems and a

Water Sources for Cyanobacteria Below Desert Rocks in the Negev Desert Determined by Conductivity

Science.gov (United States)

McKay, Christopher P.

2016-01-01

We present year round meteorological and conductivity measurements of colonized hypolithic rocks in the Arava Valley, Negev Desert, Israel. The data indicate that while dew is common in the Negev it is not an important source of moisture for hypolithic organisms at this site. The dominance of cyanobacteria in the hypolithic community are consistent with predictions that cyanobacteria are confined to habitats supplied by rain. To monitor the presence of liquid water under the small Negev rocks we developed and tested a simple field conductivity system based on two wires placed about 0.5 cm apart. Based on 21 replicates recorded for one year in the Negev we conclude that in natural rains (0.25 mm to 6 mm) the variability between sensor readings is between 20 and 60% decreasing with increasing rain amount. We conclude that the simple small electrical conductivity system described here can be used effectively to monitor liquid water levels in lithic habitats. However, the natural variability of these sensors indicates that several replicates should be deployed. The results and method presented have use in arid desert reclamation programs.

Delayed visual maturation is not from lead pollution

International Nuclear Information System (INIS)

Gulson, B.L.; Howarth, D.

2000-01-01

radioactive decay, the amounts (abundances) have changed over geological time and this is reflected in the geological source of the lead. The abundances are usually expressed as ratios. Lead from the geologically old (∼1700 million years old) lead-zinc-silver deposits of Broken Hill in NSW has an 206 Pb/ 204 Pb abundance ratio of 16.00 whereas the ratio is 18.1-18.3 for geologically young deposits, 500-400 million years old, on the same continent or from the northern hemisphere. It is these isotopic differences that are used to evaluate the source of lead in the environment, humans and animals. Interpretations of lead isotopic data may not be straightforward because lead in the environment or animals may be a mixture of lead from different sources (mines). Hence, lead that is introduced to the body from air/food/water is largely dependent on the source of lead in the environment, which in turn is dependent on the age and hence isotopic composition of the rocks/ores from which the lead in the environment is derived

Source rock formation evaluation using TOC & Ro log model based on well-log data procesing: study case of Ngimbang formation, North East Java basin

Directory of Open Access Journals (Sweden)

Fatahillah Yosar

2017-01-01

Full Text Available Ngimbang Formation is known as one major source of hydrocarbon supply in the North Eastern Java Basin. Aged Mid-Eocene, Ngimbang is dominated by sedimentary clastic rocks mostly shale, shaly sandstone, and thick layers of limestone (CD Limestone, with thin layers of coal. Although, laboratory analyses show the Ngimbang Formation to be a relatively rich source-rocks, such data are typically too limited to regionally quantify the distribution of organic matter. To adequately sample the formation both horizontally and vertically on a basin–wide scale, large number of costly and time consuming laboratory analyses would be required. Such analyses are prone to errors from a number of sources, and core data are frequently not available at key locations. In this paper, the authors established four TOC (Total Organic Carbon Content logging calculation models; Passey, Schmoker-Hester, Meyer-Nederloff, and Decker/Density Model by considering the geology of Ngimbang. Well data along with its available core data was used to determine the most suitable model to be applied in the well AFA-1, as well as to compare the accuracy of these TOC model values. The result shows good correlation using Decker (TOC Model and Mallick-Raju (Ro- Vitrinite Reflectance Model. Two source rocks potential zones were detected by these log models.

Modeling the Rock Glacier Cycle

Science.gov (United States)

Anderson, R. S.; Anderson, L. S.

2016-12-01

Rock glaciers are common in many mountain ranges in which the ELA lies above the peaks. They represent some of the most identifiable components of today's cryosphere in these settings. Their oversteepened snouts pose often-overlooked hazards to travel in alpine terrain. Rock glaciers are supported by avalanches and by rockfall from steep headwalls. The winter's avalanche cone must be sufficiently thick not to melt entirely in the summer. The spatial distribution of rock glaciers reflects this dependence on avalanche sources; they are most common on lee sides of ridges where wind-blown snow augments the avalanche source. In the absence of rockfall, this would support a short, cirque glacier. Depending on the relationship between rockfall and avalanche patterns, "talus-derived" and "glacier-derived" rock glaciers are possible. Talus-derived: If the spatial distribution of rock delivery is similar to the avalanche pattern, the rock-ice mixture will travel an englacial path that is downward through the short accumulation zone before turning upward in the ablation zone. Advected debris is then delivered to the base of a growing surface debris layer that reduces the ice melt rate. The physics is identical to the debris-covered glacier case. Glacier-derived: If on the other hand rockfall from the headwall rolls beyond the avalanche cone, it is added directly to the ablation zone of the glacier. The avalanche accumulation zone then supports a pure ice core to the rock glacier. We have developed numerical models designed to capture the full range of glacier to debris-covered glacier to rock glacier behavior. The hundreds of meter lengths, tens of meters thicknesses, and meter per year speeds of rock glaciers are well described by the models. The model can capture both "talus-derived" and "glacier-derived" rock glaciers. We explore the dependence of glacier behavior on climate histories. As climate warms, a pure ice debris-covered glacier can transform to a much shorter rock

Interim rock mass properties and conditions for analyses of a repository in crystalline rock

International Nuclear Information System (INIS)

Tammemagi, H.Y.; Chieslar, J.D.

1985-03-01

A summary of rock properties for generic crystalline rock is compiled from literature sources to provide the input data for analyses of a conceptual repository in crystalline rock. Frequency histograms, mean values and ranges of physical, mechanical, thermal, and thermomechanical properties, and the dependence of these properties on temperature are described. A description of the hydrogeologic properties of a crystalline rock mass and their dependence on depth is provided. In addition, the temperature gradients, mean annual surface temperature, and in situ stress conditions are summarized for the three regions of the United States currently under consideration to host a crystalline repository; i.e., the North Central, Northeastern, and Southeastern. Brief descriptions of the regional geology are also presented. Large-scale underground experiments in crystalline rock at Stripa, Sweden, and in Climax Stock in Nevada, are reviewed to assess whether the rock properties presented in this report are representative of in situ conditions. The suitability of each rock property and the sufficiency of its data base are described. 110 refs., 27 figs., 4 tabs

The efficiency of in vitro ovine embryo production using an undefined or a defined maturation medium is determined by the source of the oocyte.

Science.gov (United States)

Cocero, M J; Alabart, J L; Hammami, S; Martí, J I; Lahoz, B; Sánchez, P; Echegoyen, E; Beckers, J F; Folch, J

2011-06-01

In vitro oocyte maturation can be influenced by oocyte source and maturation media composition. The aim of the present study was to compare the efficiency of a defined in vitro maturation medium (TCM199 supplemented with cysteamine and epidermal growth factor; Cys + EGF) with an undefined medium (TCM199 supplemented with follicle-stimulating hormone and follicular fluid; FSH + FF) for in vitro production (IVP) of ovine embryos, using oocytes obtained by laparoscopic ovum pick-up from FSH-stimulated [n=11; 158 cumulus-oocyte complexes (COCs)] and non-stimulated (n=16; 120 COCs) live ewes, as well as abattoir-derived oocytes (170 COCs). The produced blastocysts were vitrified and some of them were transferred to synchronized recipients. The best and the worst final yields of embryo IVP observed in this study were obtained using oocytes from FSH-stimulated ewes matured in FSH + FF (41.3%; 33/80) and in Cys + EGF (19.2%; 15/78) medium, respectively (p<0.01). No significant differences between both media were attained in the blastocyst development rate or in the final yield of embryo IVP using oocytes from non-stimulated ewes or abattoir-derived oocytes. The overall in vivo survival rate of the transferred vitrified blastocysts was 13.1% (8/61), without significant differences between oocyte sources or maturation media. In conclusion, under the experimental conditions of the present study, TCM199 supplemented with cysteamine and EGF is a convenient defined maturation medium for IVP of embryos from oocytes of live non-stimulated ewes or from oocytes of abattoir-derived ovaries. However, the best final yield of embryo IVP observed in this study was attained when oocytes came from FSH-stimulated donors and TCM199 was supplemented with FSH and follicular fluid. © 2010 Blackwell Verlag GmbH.

Changes in polyphenolics during maturation of Java plum (Syzygium cumini Lam.).

Science.gov (United States)

Lestario, Lydia Ninan; Howard, Luke R; Brownmiller, Cindi; Stebbins, Nathan B; Liyanage, Rohana; Lay, Jackson O

2017-10-01

Java plum (Syzygium cumini Lam.) is a rich source of polyphenolics with many purported health benefits, but the effect of maturation on polyphenolic content is unknown. Freeze-dried samples of Java plum from seven different maturity stages were analyzed for anthocyanin, flavonol, flavanonol and hydrolysable tannin composition by HPLC. Anthocyanins were first detected at the green-pink stage of maturity and increased throughout maturation with the largest increase occurring from the dark purple to black stages of maturation. Levels of gallotannins, ellagitannins, flavonols, gallic acid and ellagic acid were highest at early stages of maturation and decreased as the fruit ripened. For production of antioxidant-rich nutraceutical ingredients, fruit should be harvested immature to obtain extracts rich in hydrolysable tannins and flavonols. The exceptional anthocyanin content of black fruit may prove useful as a source of a natural colorant. Copyright © 2017 Elsevier Ltd. All rights reserved.

Thermal maturity of northern Appalachian Basin Devonian shales: Insights from sterane and terpane biomarkers

Science.gov (United States)

Hackley, Paul C.; Ryder, Robert T.; Trippi, Michael H.; Alimi, Hossein

2013-01-01

To better estimate thermal maturity of Devonian shales in the northern Appalachian Basin, eleven samples of Marcellus and Huron Shale were characterized via multiple analytical techniques. Vitrinite reflectance, Rock–Eval pyrolysis, gas chromatography (GC) of whole rock extracts, and GC–mass spectrometry (GCMS) of extract saturate fractions were evaluated on three transects that lie across previously documented regional thermal maturity isolines. Results from vitrinite reflectance suggest that most samples are immature with respect to hydrocarbon generation. However, bulk geochemical data and sterane and terpane biomarker ratios from GCMS suggest that almost all samples are in the oil window. This observation is consistent with the presence of thermogenic gas in the study area and higher vitrinite reflectance values recorded from overlying Pennsylvanian coals. These results suggest that vitrinite reflectance is a poor predictor of thermal maturity in early mature areas of Devonian shale, perhaps because reported measurements often include determinations of solid bitumen reflectance. Vitrinite reflectance interpretations in areas of early mature Devonian shale should be supplanted by evaluation of thermal maturity information from biomarker ratios and bulk geochemical data.

Water sources for cyanobacteria below desert rocks in the Negev Desert determined by conductivity

Directory of Open Access Journals (Sweden)

Christopher P. McKay

2016-04-01

Full Text Available We present year round meteorological and conductivity measurements of colonized hypolithic rocks in the Arava Valley, Negev Desert, Israel. The data indicate that while dew is common in the Negev it is not an important source of moisture for hypolithic organisms at this site. The dominance of cyanobacteria in the hypolithic community is consistent with predictions that cyanobacteria are confined to habitats supplied by rain. To monitor the presence of liquid water under the small Negev rocks we developed and tested a simple field conductivity system based on two wires placed about 0.5 cm apart. Based on 21 replicates recorded for one year in the Negev we conclude that in natural rains (0.25 mm to 6 mm the variability between sensor readings is between 20 and 60% decreasing with increasing rain amount. We conclude that the simple small electrical conductivity system described here can be used effectively to monitor liquid water levels in lithic habitats. However, the natural variability of these sensors indicates that several replicates should be deployed. The results and method presented have use in arid desert reclamation programs.

Convergent evidence for widespread rock nitrogen sources in Earth’s surface environment

Science.gov (United States)

Houlton, B. Z.; Morford, S. L.; Dahlgren, R. A.

2018-04-01

Nitrogen availability is a pivotal control on terrestrial carbon sequestration and global climate change. Historical and contemporary views assume that nitrogen enters Earth’s land-surface ecosystems from the atmosphere. Here we demonstrate that bedrock is a nitrogen source that rivals atmospheric nitrogen inputs across major sectors of the global terrestrial environment. Evidence drawn from the planet’s nitrogen balance, geochemical proxies, and our spatial weathering model reveal that ~19 to 31 teragrams of nitrogen are mobilized from near-surface rocks annually. About 11 to 18 teragrams of this nitrogen are chemically weathered in situ, thereby increasing the unmanaged (preindustrial) terrestrial nitrogen balance from 8 to 26%. These findings provide a global perspective to reconcile Earth’s nitrogen budget, with implications for nutrient-driven controls over the terrestrial carbon sink.

Waste-rock interactions and bedrock reactions

International Nuclear Information System (INIS)

White, W.B.

1977-01-01

The experimental program is designed to discover possible reactions between shale repository rocks and radioactive wastes. The canister can be regarded in three ways: (a) As a source of heat that modifies the mineralogy and therefore the physical properties of the surrounding rock (dry heat). (b) As a source of heat that activates reactions between minerals in the surrounding rock and slowly percolating ground water. (c) As a source of reaction materials of different composition from the surrounding rock and which therefore may react to form completely new ''minerals'' in a contact aureole around the canister. The matrix of interactions contains two composition axes. The waste compositions are defined by the various prototype waste forms usually investigated: glass, calcine, ''spent fuel'' and the ceramic supercalcine. The temperatures and pressures at which these reactions take place must be investigated. Thus each node on the ''wiring diagram'' is itself a matrix of experiments in which the T and to some extent P are varied. Experiments at higher pressure and temperature allow reactions to take place on a laboratory time scale and thus identify what could happen. These reactions are then followed downward in temperature to determine both phase boundaries and kinetic cut-offs below which equilibrium cannot be achieved on a laboratory time scale

La pyrolyse Rock-Eval et ses applications. Troisième partie. Rock-Eval Pyrolysis and Its Applications (Part Three

Directory of Open Access Journals (Sweden)

Espitalie J.

2006-11-01

techniques du raffinage et de la récupération secondaire des bruts. The Rock-Eval pyrolysis method was designed to meet the needs of petroleum prospection and has now gained widespread use. It quickly provides different data on the organic content of rocks, such as the petroleum potential of series encountered, the nature of kerogens and their state of maturity. Two new versions of this equipment have been developed by Institut Français du Pétrole (IFP since the appearance of the first Rock-Eval devices in 1977. One is a Rock-Eval II that is completely automated thanks to its microprocessor and is also equipped with a module for determining the organic-carbon content. The other is a Rock-Eval III (Oil Show Analyzer which is different from the preceding one in that it makes a separate analysis of gas and oil as well as determining the organic-carbon content in place of peak S3. Concerning the interpretation of the method, experience gained both by applications to sedimentary basins and by experimental investigations in the laboratory has provided a better understanding of the parameters used (peaks S1, S2 and S3, pyrolysis temperature Tmax through their variations and, from this, better insight into the application limits of the method. Concerning the application of the method, the vertical representation of results in the form of geochemical logs leads to an interpretation that is both effective and practical. Reference charts and diagrams are used to characterize source rocks (petroleum potentials, types of organic matter, degree of evolution, weathering, etc. as well as migration phenomena. The compiling of geochemical maps on a basin-wide scale then becomes possible. Likewise, the method has left the field of petroleum prospection per se and found applications in the analyzing of coals, bituminous rocks, recent sediments and even techniques of the refining and secondary recovery of crude oils.

La pyrolyse Rock-Eval et ses applications. Première partie. Rock-Eval Pyrolysis and Its Applications (Part One

Directory of Open Access Journals (Sweden)

Espitalie J.

2006-11-01

techniques du raffinage et de la récupération secondaire des bruts. The Rock-Eval pyrolysis method was designed to meet the needs of petroleum prospection and has now gained widespread use. It quickly provides different data on the organic content of rocks, such as the petroleum potential of series encountered, the nature of kerogens and their state of maturity. Two new versions of this equipment have been developed by Institut Français du Pétrole (IFP since the appearance of the first Rock-Eval devices in 1977. One is a Rock-Eval II that is completely automated thanks to its microprocessor and is also equipped with a module for determining the organic-carbon content. The other is a Rock-Eval III (Oil Show Analyzer which is different from the preceding one in that it makes a separate analysis of gas and oil as well as determining the organic-carbon content in place of peak S3. Concerning the interpretation of the method, experience gained both by applications to sedimentary basins and by experimental investigations in the laboratory has provided a better understanding of the parameters used (peaks S1, S2 and S3, pyrolysis temperature Tmax through their variations and, from this, better insight into the application limits of the method. Concerning the application of the method, the vertical representation of results in the form of geochemical logs leads to an interpretation that is both effective and practical. Reference charts and diagrams are used to characterize source rocks (petroleum potentials, types of organic matter, degree of evolution, weathering, etc. as well as migration phenomena. The compiling of geochemical maps on a basin-wide scale then becomes possible. Likewise, the method has left the field of petroleum prospection per se and found applications in the analyzing of coals, bituminous rocks, recent sediments and even techniques of the refining and secondary recovery of crude oils.

La pyrolyse Rock-Eval et ses applications. Deuxième partie. Rock-Eval Pyrolysis and Its Applications (Part Two

Directory of Open Access Journals (Sweden)

Espitalie J.

2006-11-01

techniques du raffinage et de la récupération secondaire des bruts. The Rock-Eval pyrolysis method was designed to meet the needs of petroleum prospection and has now gained widespread use. It quickly provides different data on the organic content of rocks, such as the petroleum potential of series encountered, the nature of kerogens and their state of maturity. Two new versions of this equipment have been developed by Institut Français du Pétrole (IFP since the appearance of the first Rock-Eval devices in 1977. One is a Rock-Eval II that is completely automated thanks to its microprocessor and is also equipped with a module for determining the organic-carbon content. The other is a Rock-Eval III (Oil Show Analyzer which is different from the preceding one in that it makes a separate analysis of gas and oil as well as determining the organic-carbon content in place of peak S3. Concerning the interpretation of the method, experience gained both by applications to sedimentary basins and by experimental investigations in the laboratory has provided a better understanding of the parameters used (peaks S1, S2 and S3, pyrolysis temperature Tmax through their variations and, from this, better insight into the application limits of the method. Concerning the application of the method, the vertical representation of results in the form of geochemical logs leads to an interpretation that is both effective and practical. Reference charts and diagrams are used to characterize source rocks (petroleum potentials, types of organic matter, degree of evolution, weathering, etc. as well as migration phenomena. The compiling of geochemical maps on a basin-wide scale then becomes possible. Likewise, the method has left the field of petroleum prospection per se and found applications in the analyzing of coals, bituminous rocks, recent sediments and even techniques of the refining and secondary recovery of crude oils.

Late Archaean-early Proterozoic source ages of zircons in rocks from the Paleozoic orogen of western Galicia, NW Spain

Energy Technology Data Exchange (ETDEWEB)

Kuijper, R P; Priem, H N.A. [Laboratorium voor Isotopen-Geologie, Amsterdam (Netherlands); Den Tex, E [Rijksuniversiteit Utrecht (Netherlands). Inst. voor Aardwetenschappen

1982-08-01

U-Pb data are reported for nine suites of zircons and three monazites from the Paleozoic orogen in western Galicia: one paragneiss and six orthogneisses from the early Paleozoic basement, and two Carboniferous (ca. 310 Ma old) intrusions of two-mica granite. New whole-rock Rb-Sr analyses, along with earlier data, indicate an age of ca. 470-440 Ma (Ordovician) for the emplacement of the granitic precursors of the orthogneisses. Monazite from the paragneiss also yields an U-Pb age of ca. 470 Ma. From the high initial /sup 87/Sr//sup 86/Sr ratios an involvement of Precambrian continental crust material is evident in the generation of the early Paleozoic suite of granites, while the zircon U-Pb data give evidence of the presence of about 3.0-2.0 Ga old (late Archaean-early Proterozoic) components in the source material. Zircons from the oldest sedimentary rocks in the area, now present as catazonal paragneisses and a likely source for the granites, likewise reveal a provenance age of 3.0-2.0 Ga.

Convergent evidence for widespread rock nitrogen sources in Earth's surface environment.

Science.gov (United States)

Houlton, B Z; Morford, S L; Dahlgren, R A

2018-04-06

Nitrogen availability is a pivotal control on terrestrial carbon sequestration and global climate change. Historical and contemporary views assume that nitrogen enters Earth's land-surface ecosystems from the atmosphere. Here we demonstrate that bedrock is a nitrogen source that rivals atmospheric nitrogen inputs across major sectors of the global terrestrial environment. Evidence drawn from the planet's nitrogen balance, geochemical proxies, and our spatial weathering model reveal that ~19 to 31 teragrams of nitrogen are mobilized from near-surface rocks annually. About 11 to 18 teragrams of this nitrogen are chemically weathered in situ, thereby increasing the unmanaged (preindustrial) terrestrial nitrogen balance from 8 to 26%. These findings provide a global perspective to reconcile Earth's nitrogen budget, with implications for nutrient-driven controls over the terrestrial carbon sink. Copyright © 2018 The Authors, some rights reserved; exclusive licensee American Association for the Advancement of Science. No claim to original U.S. Government Works.

A heat source probe for measuring thermal conductivity in waste rock dumps

International Nuclear Information System (INIS)

Blackford, M.G.; Harries, J.R.

1985-10-01

The development and use of a heat source probe to measure the thermal conductivity of the material in a waste rock dump is described. The probe releases heat at a constant rate into the surrounding material and the resulting temperature rise is inversely related to the thermal conductivity. The probe was designed for use in holes in the dump which are lined with 50 mm i.d. polyethylene liners. The poor thermal contact between the probe and the liner and the unknown conductivity of the backfill material around the liner necessitated long heating and cooling times (>10 hours) to ensure that the thermal conductivity of the dump material was being measured. Temperature data acquired in the field were analysed by comparing them with temperatures calculated using a two-dimensional cylindrical model of the probe and surrounding material, and the heat transfer code HEATRAN

Maturity in the Styrian Basin. Maturitaet im Steirischen Tertiaerbecken

Energy Technology Data Exchange (ETDEWEB)

Sachsenhofer, R.F. (Montanuniversitaet Leoben (Austria). Inst. fuer Geowissenschaften/Geologie)

1991-01-01

The Styrian basin, situated at the south-eastern margin of the Alps, contains up to 3 km of Ottnangian to Pliocene sedimentary rocks. Main subsidence occured between Ottnangian and Sarmatian. Miocene and Plio-/Pleistocene volcanic phases can be distinguished. Maturity in the Styrian basin was studied with vitrinite reflectance curves of 25 boreholes. The oil window lies at shallow depths in the vicinty of Miocene volcanos. This is due to high heating rate during Karpatian to Lower Badenian times. Depth and thickness of the oil window increase with increasing distance from these volcanos. At a distance of some kilometers the thermal influence of this Miocene volcanism disappears. According to high recent heat flow the oil window is located below 1 500 to 2 000 m in these parts of the basin. An influence of Plio-/Pleistocene volcanism on maturity cannot be observed. (orig.).

Tomato seeds maturity detection system based on chlorophyll fluorescence

Science.gov (United States)

Li, Cuiling; Wang, Xiu; Meng, Zhijun

2016-10-01

Chlorophyll fluorescence intensity can be used as seed maturity and quality evaluation indicator. Chlorophyll fluorescence intensity of seed coats is tested to judge the level of chlorophyll content in seeds, and further to judge the maturity and quality of seeds. This research developed a detection system of tomato seeds maturity based on chlorophyll fluorescence spectrum technology, the system included an excitation light source unit, a fluorescent signal acquisition unit and a data processing unit. The excitation light source unit consisted of two high power LEDs, two radiators and two constant current power supplies, and it was designed to excite chlorophyll fluorescence of tomato seeds. The fluorescent signal acquisition unit was made up of a fluorescence spectrometer, an optical fiber, an optical fiber scaffolds and a narrowband filter. The data processing unit mainly included a computer. Tomato fruits of green ripe stage, discoloration stage, firm ripe stage and full ripe stage were harvested, and their seeds were collected directly. In this research, the developed tomato seeds maturity testing system was used to collect fluorescence spectrums of tomato seeds of different maturities. Principal component analysis (PCA) method was utilized to reduce the dimension of spectral data and extract principal components, and PCA was combined with linear discriminant analysis (LDA) to establish discriminant model of tomato seeds maturity, the discriminant accuracy was greater than 90%. Research results show that using chlorophyll fluorescence spectrum technology is feasible for seeds maturity detection, and the developed tomato seeds maturity testing system has high detection accuracy.

ORGANIZATIONAL PROJECT MANAGEMENT MATURITY

Directory of Open Access Journals (Sweden)

Yana Derenskaya

2017-11-01

Full Text Available The present article is aimed at developing a set of recommendations for achieving a higher level of organizational project maturity at a given enterprise. Methodology. For the purposes of the current research, the available information sources on the components of project management system are analysed; the essence of “organizational maturity” and the existing models of organizational maturity are studied. The method of systemic and structural analysis, as well as the method of logical generalization, are employed in order to study the existing models of organizational maturity, to describe levels of organizational maturity, and finally to develop a set of methodological recommendations for achieving a higher level of organizational project maturity at a given enterprise. The results of the research showed that the core elements of project management system are methodological, organizational, programtechnical, and motivational components. Project management encompasses a wide range of issues connected with organizational structure, project team, communication management, project participants, etc. However, the fundamental basis for developing project management concept within a given enterprise starts with defining its level of organizational maturity. The present paper describes various models of organizational maturity (staged, continuous, petal-shaped and their common types (H. Кеrzner Organizational Maturity Model, Berkeley PM Maturity Model, Organizational Project Management Maturity Model, Portfolio, Program & Project Management Maturity Model. The analysis of available theoretic works showed that the notion “organizational project maturity” refers to the capability of an enterprise to select projects and manage them with the intention of achieving its strategic goals in the most effective way. Importantly, the level of maturity can be improved by means of formalizing the acquired knowledge, regulating project-related activities

The search for a source rock for the giant Tar Sand triangle accumulation, southeastern Utah

Science.gov (United States)

Huntoon, J.E.; Hansley, P.L.; Naeser, N.D.

1999-01-01

A large proportion (about 36%) of the world's oil resource is contained in accumulations of heavy oil or tar. In these large deposits of degraded oil, the oil in place represents only a fraction of what was present at the time of accumulation. In many of these deposits, the source of the oil is unknown, and the oil is thought to have migrated over long distances to the reservoirs. The Tar Sand triangle in southeastern Utah contains the largest tar sand accumulation in the United States, with 6.3 billion bbl of heavy oil estimated to be in place. The deposit is thought to have originally contained 13-16 billion bbl prior to the biodegradation, water washing, and erosion that have taken place since the middle - late Tertiary. The source of the oil is unknown. The tar is primarily contained within the Lower Permian White Rim Sandstone, but extends into permeable parts of overlying and underlying beds. Oil is interpreted to have migrated into the White Rim sometime during the Tertiary when the formation was at a depth of approximately 3500 m. This conclusion is based on integration of fluid inclusion analysis, time-temperature reconstruction, and apatite fission-track modeling for the White Rim Sandstone. Homogenization temperatures cluster around 85-90??C for primary fluid inclusions in authigenic, nonferroan dolomite in the White Rim. The fluid inclusions are associated with fluorescent oil-bearing inclusions, indicating that dolomite precipitation was coeval with oil migration. Burial reconstruction suggests that the White Rim Sandstone reached its maximum burial depth from 60 to 24 Ma, and that maximum burial was followed by unroofing from 24 to 0 Ma. Time-temperature modeling indicates that the formation experienced temperatures of 85-90??C from about 35 to 40 Ma during maximum burial. Maximum formation temperatures of about 105-110??C were reached at about 24 Ma, just prior to unroofing. Thermal modeling is used to examine the history of potential source rocks

Heat production in granitic rocks

DEFF Research Database (Denmark)

Artemieva, Irina; Thybo, Hans; Jakobsen, Kiki

2017-01-01

Granitic rocks play special role in the dynamics and evolution of the Earth and its thermal regime. First, their compositional variability, reflected in the distribution of concentrations of radiogenic elements, provides constraints on global differentiation processes and large scale planetary...... evolution, where emplacement of granites is considered a particularly important process for the formation of continental crust. Second, heat production by radioactive decay is among the main heat sources in the Earth. Therefore knowledge of heat production in granitic rocks is pivotal for thermal modelling...... of the continental lithosphere, given that most radiogenic elements are concentrated in granitic rocks of the upper continental crust whereas heat production in rocks of the lower crust and lithospheric mantle is negligible. We present and analyze a new global database GRANITE2017 (with about 500 entries...

Silurian and Devonian source rocks and crude oils from the western part of Libya: Organic geochemistry, palynology and carbon stratigraphy

NARCIS (Netherlands)

Elkelani, Mohamed M.A.

2015-01-01

The Early Silurian “hot” shales and Late Devonian black shales are major regional oil and gas source rocks in North Africa. Their deposition probably played a major role in global carbon cycling in general because of the large areas of the ocean affected. Comparing the Libyan δ13C record with

Thermophysical properties of rocks: a perspective on data needs, sources and accuracy

International Nuclear Information System (INIS)

Stephens, H.P.; Sinnock, S.

1979-01-01

Recent emphasis on research in geologic isolation of nuclear wastes and geoenergy resource development has created a renewed demand for engineering thermophysical property data for rocks and other geologic materials at elevated pressures and temperatures. In contrast to fabricated engineering materials, with properties which can be specified, rocks used in engineering design are complex, naturally occurring materials having properties which must be characterized, rather than specified, for engineering studies. Much difficulty in measuring, reporting, and using thermophysical properties of rocks results from (1) rock inhomogeneity and anisotropy on both microscopic and macroscopic scales; (2) inclusion of pore fluids, such as water; and (3) measurement of laboratory properties under conditions quite different from those of in situ material. Because measurements on in situ materials are scarce, many analyses must depend on extrapolated values of uncertain accuracy. A survey of thermophysical property data available for geologic thermal transport studies indicates that caution must be taken to effectively match data abstracted from the literature with project objectives

Analysis of business process maturity and organisational performance relations

Directory of Open Access Journals (Sweden)

Kalinowski T. Bartosz

2016-12-01

Full Text Available The paper aims to present results of the study on business process maturity in relation to organisational performance. A two-phase methodology, based on literature review and survey was used. The literature is a source of knowledge about business process maturity and organisational performance, whereas the research on process maturity vs organisational performance in Polish Enterprises provides findings based on 84 surveyed companies. The main areas of the research covered: identification and analysis of maturity related variables and identification of organisational performance perspectives and its relation to process maturity. The study shows that there is a significant positive relation between process maturity and organisational performance. Although there are research on such relation available, they are scarce and have some significant limitations in terms of research sample or the scope of maturity or organisational performance covered. This publication is part of a project funded by the National Science Centre awarded by decision number DEC-2011/01/D/HS4/04070.

Growing Pebbles and Conceptual Prisms - Understanding the Source of Student Misconceptions about Rock Formation.

Science.gov (United States)

Kusnick, Judi

2002-01-01

Analyzes narrative essays--stories of rock formation--written by pre-service elementary school teachers. Reports startling misconceptions among preservice teachers on pebbles that grow, human involvement in rock formation, and sedimentary rocks forming as puddles as dry up, even though these students had completed a college level course on Earth…

Study on performance of a simultaneous spectrometer of ICP emission source for the determination of the major elements in rocks

International Nuclear Information System (INIS)

Vieira, M.D.

1987-01-01

The optimization of operational parameters of a simultaneous spectrometer coupled to an ICP excitation source in order to establish an analytical method for the simultaneous determination of the major elements in rocks is studied. The mutual spectral interferences, calibration curves for the acid and saline matrix and the internal standard method with ytrium are analyzed. (M.J.C.) [pt

The organic petrology and thermal maturity of Lower Carboniferous and Upper Devonian source rocks in the Liard Basin, at Jackfish Gap-Yohin Ridge and North Beaver River, northern Canada: Implications for hydrocarbon exploration

Energy Technology Data Exchange (ETDEWEB)

Potter, J. (Univ. of Newcastle-upon-Tyne (United Kingdom)); Richards, B.C.; Goodarzi, G. (Geological Survey, Calgary, Alberta (Canada))

Basinal shales of the Besa River Fm. have TOC values ranging from 1 to 4% and contain abundant type II, dominantly amorphous, kerogen of marine origin. Shales in the Yohin, Clausen, Prophet, and Golata Formations are of mixed maring and terrestrial origins and yield TOC values of 1 to 3%. Kerogen in the Golata and Yohin Formations are dominated by terrestrial components, while the Clausen and Flett kerogen comprises marine liptinites and bitumens. Kerogen from the deltaic Mattson shales at Jackfish Gap are types II and III, having mixed marine and terrestrial origins consistent with shallow, nearshore, subtidal environments. The coals are sapropelic and probably lacustrine in origin. Algal laminites associated with coals in the Upper Mattson have >10% TOC values, while non-laminite shales contain between 2 and 5% TOC. Comparable measured and calculated vitrinite reflectance data indicate that kerogen in the Lower Carboniferous at Jackfish Gap is mature. Kerogen in correlative formations in the subsurface at North Beaver River is more marine. Vitrinites are rate and oxidized, but four populations of bitumens are distinguished on the basis of relative reflectivity and morphological or petrophysical associations. Types A and B bitumens are primary and by-products of hydrocarbon generation from type II (algal and amorphous) kerogens. Correlations between depth and reflectance of bitumens A and B are very good. Vitrinite reflectance data calculated from bitumen reflectance measurements for the Besa River, Prophet, and Golata indicate that they are potential sources of catagenic gas. The Mattson kerogen is mature, oil and gas-prone.

Development of uniform hazard response spectra for rock sites considering line and point sources of earthquakes

International Nuclear Information System (INIS)

Ghosh, A.K.; Kushwaha, H.S.

2001-12-01

Traditionally, the seismic design basis ground motion has been specified by normalised response spectral shapes and peak ground acceleration (PGA). The mean recurrence interval (MRI) used to computed for PGA only. It is shown that the MRI associated with such response spectra are not the same at all frequencies. The present work develops uniform hazard response spectra i.e. spectra having the same MRI at all frequencies for line and point sources of earthquakes by using a large number of strong motion accelerograms recorded on rock sites. Sensitivity of the number of the results to the changes in various parameters has also been presented. This work is an extension of an earlier work for aerial sources of earthquakes. These results will help to determine the seismic hazard at a given site and the associated uncertainities. (author)

Organic petrology and Rock-Eval characteristics in selected surficial samples of the Tertiary Formation, South Sumatra Basin

Directory of Open Access Journals (Sweden)

M. H. Hermiyanto

2014-06-01

Full Text Available http://dx.doi.org/10.17014/ijog.vol4no3.20096Organic petrologic data of the DOM of Talangakar and Muaraenim Formations show that the organic matter consisting mainly of vitrinite group is essentially composed of telocollinite (1.0 – 70.8 % and desmocollinite (0.8 – 66.6 % with minor telinite (0.6 – 9.4 %, detrovitrinite (0.6 – 6.0 %, and cor- pocollinite (0.6 – 2.0 %. Minor exinite (0.4 – 7.8 % and inertinite (0.4 – 8.0 % are also determined. However, mineral matter varies from 0.6 – 99.44 %. Downwards, the increase in vitrinite reflectance (0.33 – 0.48 % is concomitant with the depth of each formation. Furthermore, based on Rock-eval pyrolysis, TOC value of the Talangakar Formation ranges from 0.09 – 15.38 %, Gumai 0.34 – 0.39 %, Airbenakat 0.32 – 4.82 %, and Muaraenim between 0.08 – 15.22 %. Moreover the PY (Potential Yield value variation of the Talangakar, Gumai, Airbenakat, and Muaraenim Formations are between 0.04 – 36.61 mg HC/g rock, 0.53 – 0.81 mg HC/g rock, 0.1 – 4.37 mg HC/g rock, and 0.07 – 129.8 mg HC/g rock respectively. Therefore, on the basis of those two parameters, the four formations are included into a gas - oil prone source rock potential. However, the Talangakar and Muaraenim Formations are poor to excellent category, whereas the Air Benakat tends to indicate a poor – fair category and Gumai Formation are only within a poor category. Tmax value of the Talangakar ranges from 237 – 4380 C, Gumai 316 – 3590 C, Airbenakat 398 – 4340 C with exceptions of 4970 C and 5180 C, and Muaraenim Forma- tions 264 – 4250 C. The Talangakar Formation contains kerogen Type II dan III, with the HI (Hydrogen Index value varies from 45.16 – 365.43. However two samples show value of 0. The organic content of the Gumai and Air Benakat Formations are included into kerogen type III, with HI value ranges from11.87 – 40.82, and 19 – 114 respectively. Moreover the Muaraenim Formation has two category of

Correlation between dental maturity and cervical vertebral maturity.

Science.gov (United States)

Chen, Jianwei; Hu, Haikun; Guo, Jing; Liu, Zeping; Liu, Renkai; Li, Fan; Zou, Shujuan

2010-12-01

The aim of this study was to investigate the association between dental and skeletal maturity. Digital panoramic radiographs and lateral skull cephalograms of 302 patients (134 boys and 168 girls, ranging from 8 to 16 years of age) were examined. Dental maturity was assessed by calcification stages of the mandibular canines, first and second premolars, and second molars, whereas skeletal maturity was estimated by the cervical vertebral maturation (CVM) stages. The Spearman rank-order correlation coefficient was used to measure the association between CVM stage and dental calcification stage of individual teeth. The mean chronologic age of girls was significantly lower than that of boys in each CVM stage. The Spearman rank-order correlation coefficients between dental maturity and cervical vertebral maturity ranged from 0.391 to 0.582 for girls and from 0.464 to 0.496 for boys (P cervical vertebral maturation stage. The development of the mandibular second molar in females and that of the mandibular canine in males had the strongest correlations with cervical vertebral maturity. Therefore, it is practical to consider the relationship between dental and skeletal maturity when planning orthodontic treatment. Copyright © 2010 Mosby, Inc. All rights reserved.

Fluids in crustal deformation: Fluid flow, fluid-rock interactions, rheology, melting and resources

Science.gov (United States)

Lacombe, Olivier; Rolland, Yann

2016-11-01

Fluids exert a first-order control on the structural, petrological and rheological evolution of the continental crust. Fluids interact with rocks from the earliest stages of sedimentation and diagenesis in basins until these rocks are deformed and/or buried and metamorphosed in orogens, then possibly exhumed. Fluid-rock interactions lead to the evolution of rock physical properties and rock strength. Fractures and faults are preferred pathways for fluids, and in turn physical and chemical interactions between fluid flow and tectonic structures, such as fault zones, strongly influence the mechanical behaviour of the crust at different space and time scales. Fluid (over)pressure is associated with a variety of geological phenomena, such as seismic cycle in various P-T conditions, hydrofracturing (including formation of sub-horizontal, bedding-parallel veins), fault (re)activation or gravitational sliding of rocks, among others. Fluid (over)pressure is a governing factor for the evolution of permeability and porosity of rocks and controls the generation, maturation and migration of economic fluids like hydrocarbons or ore forming hydrothermal fluids, and is therefore a key parameter in reservoir studies and basin modeling. Fluids may also help the crust partially melt, and in turn the resulting melt may dramatically change the rheology of the crust.

Mature adipocytes may be a source of stem cells for tissue engineering

International Nuclear Information System (INIS)

Fernyhough, M.E.; Hausman, G.J.; Guan, L.L.; Okine, E.; Moore, S.S.; Dodson, M.V.

2008-01-01

Adipose tissue contains a large portion of stem cells. These cells appear morphologically like fibroblasts and are primarily derived from the stromal cell fraction. Mature (lipid-filled) adipocytes possess the ability to become proliferative cells and have been shown to produce progeny cells that possess the same morphological (fibroblast-like) appearance as the stem cells from the stromal fraction. A closer examination of mature adipocyte-derived progeny cells may prove to be an emerging area of growth/metabolic physiology that may modify present thinking about adipose tissue renewal capabilities. Knowledge of these cells may also prove beneficial in cell-based therapies for tissue repair, regeneration, or engineering

Microbial Leaching of Some Valuable Elements From Egyptian Phosphate Rock

International Nuclear Information System (INIS)

Kamal, H.M.; Hassanein, R.A.; Mahdy, H.M.A.; Mahmoud, K.F.; Abouzeid, M.A.

2012-01-01

Four phosphate rock samples representing different phosphate mineralization modes in Egypt were selected from Abu Tartar, Nile valley and Red sea areas. Factors affecting the phosphate rock solubilization and some of the contained valuable elements by Aspergillus niger, Penicillium sp. and Pseudomonas fluorescence, were studied with especial orientation towards the completion of phosphate rock samples solubilization especially die low grade one. Effect of nitrogen source type on leaching efficiency by Aspergillus niger when two nitrogen sources on the phosphate bioleaching efficiency, it is clear that the ammonium chloride is more favorable as nitrogen source than sodium nitrate in the bioleaching of phosphate rocks. When Aspergillus niger was applied under die following conditions: 50 g/1 of sucrose as a carbon source, 0.1 N of ammonium chloride as a nitrogen source, 10 days incubation period, 0.5% solid: liquid ratio for P 2 O 5 and 5% for U and REE and - 270 mesh of grain size. The optimum leaching of P 2 O 5 , U and REE from phosphate rock samples reached (23.27%, 17.4%, 11.4%, respectively), while at -60 mesh they reached to 16.58%, 28.9%, 30.2% respectively. The optimum conditions for the maximal leaching efficiencies of P 2 O 5 , U and REE when applying the Penicillium sp. from the phosphate rock samples were: 100 g/1 of sucrose as a carbon source for P 2 O 5 and U and 10 g/1 for REE, 7,15 and 10 days incubation period for P 2 O 5 , U and REE, respectively, 0.5% solid: liquid ratio for P 2 O 5 and 5% for U and REE. Finally, the application of phosphate rock samples grinded to -270 mesh of grain size for P 2 O 5 and (-60 to -140) for U and REE. The studied leaching efficiency of P 2 O 5 , U and REE gave at -270 mesh 33.66%, 24.3%, 15.9% respectively, while at -60 mesh they gave 33.76%, 26.7%, 17.8% and at -140 mesh gave 31.32%, 27.9%, 17.6%, respectively.The optimum conditions for the P 2 O 5 leaching efficiency when applying the Pseudomonas fluorescence were

Near-Infrared Imaging for Spatial Mapping of Organic Content in Petroleum Source Rocks

Science.gov (United States)

Mehmani, Y.; Burnham, A. K.; Vanden Berg, M. D.; Tchelepi, H.

2017-12-01

Natural gas from unconventional petroleum source rocks (shales) plays a key role in our transition towards sustainable low-carbon energy production. The potential for carbon storage (in adsorbed state) in these formations further aligns with efforts to mitigate climate change. Optimizing production and development from these resources requires knowledge of the hydro-thermo-mechanical properties of the rock, which are often strong functions of organic content. This work demonstrates the potential of near-infrared (NIR) spectral imaging in mapping the spatial distribution of organic content with O(100µm) resolution on cores that can span several hundred feet in depth (Mehmani et al., 2017). We validate our approach for the immature oil shale of the Green River Formation (GRF), USA, and show its applicability potential in other formations. The method is a generalization of a previously developed optical approach specialized to the GRF (Mehmani et al., 2016a). The implications of this work for spatial mapping of hydro-thermo-mechanical properties of excavated cores, in particular thermal conductivity, are discussed (Mehmani et al., 2016b). References:Mehmani, Y., A.K. Burnham, M.D. Vanden Berg, H. Tchelepi, "Quantification of organic content in shales via near-infrared imaging: Green River Formation." Fuel, (2017). Mehmani, Y., A.K. Burnham, M.D. Vanden Berg, F. Gelin, and H. Tchelepi. "Quantification of kerogen content in organic-rich shales from optical photographs." Fuel, (2016a). Mehmani, Y., A.K. Burnham, H. Tchelepi, "From optics to upscaled thermal conductivity: Green River oil shale." Fuel, (2016b).

Elbow, forearm, wrist, and hand injuries among sport rock climbers.

Science.gov (United States)

Holtzhausen, L M; Noakes, T D

1996-07-01

Sport rock climbing with its repetitive high-torque movements in gaining the ascent of a rock face or wall, often in steep overhanging positions, is associated with a unique distribution and form of upper limb injuries. In this article, we review the biomechanical aspects of sport rock climbing and the types of injuries commonly encountered in the forearm, wrist, and hand regions of elite sport rock climbers. Because elbow, forearm, wrist, and hand injuries predominate, representing 62% of the total injuries encountered, these anatomical areas have been selected for review. The predominant source of data are the published work of Bollen et al. The remaining sources were obtained through electronic search of the Medline and Current Contents Databases (last searched May 1995). German and French articles were included in the search criteria. Only studies dealing with acute soft tissue and overuse injuries amongst sport rock climbers were selected. Data were extracted directly from the sourced articles. The following injuries have been described in detail with regard to their presentation, diagnosis, treatment, and prevention amongst sport rock climbers: medial epicondylitis, brachialis tendonitis, biceps brachii tendonitis, ulnar collateral ligament sprain of the elbow, carpal tunnel syndrome, digital flexor tendon pulley sheath tears, interphalangeal joint effusions, fixed flexion deformities of the interphalangeal joints, and collateral ligament tears of the interphalangeal joints. Many of the injuries are specific to the handhold types used by the rock climber. Accurate diagnosis and effective treatment of these unique injuries will be facilitated by a wider understanding of the biomechanical aspects of rock climbing and an awareness of the patterns and incidence of injuries in this sport.

High Sr/Y rocks are not all adakites!

Science.gov (United States)

Moyen, Jean-François

2010-05-01

The name of "adakite" is used to describe a far too large group of rocks, whose sole common feature is high Sr/Y and La/Yb ratios. Defining adakites only by this criterion is misleading, as the definition of this group of rocks does include many other criteria, including major elements. In itself, high (or commonly moderate!) Sr/Y ratios can be achieved via different processes: melting of a high Sr/Y (and La/Yb) source; deep melting, with abundant residual garnet; fractional crystallization or AFC; or interactions of felsic melts with the mantle, causing selective enrichment in LREE and Sr over HREE. A database of the compositions of "adakitic" rocks - including "high silica" and "low silica" adakites, "continental" adakites and Archaean adakites—was assembled. Geochemical modeling of the potential processes is used to interpret it, and reveals that (1) the genesis of high-silica adakites requires high pressure evolution (be it by melting or fractionation), in equilibrium with large amounts of garnet; (2) low-silica adakites are explained by garnet-present melting of an adakite-metasomatized mantle, i.e at depths greater than 2.5 GPa; (3) "Continental" adakites is a term encompassing a huge range of rocks, with a corresponding diversity of petrogenetic processes, and most of them are different from both low- and high- silica adakites; in fact in many cases it is a complete misnomer and the rocks studied are high-K calc-alkaline granitoids or even S-type granites; (4) Archaean adakites show a bimodal composition range, with some very high Sr/Y examples (similar to part of the TTG suite) reflecting deep melting (> 2.0 GPa) of a basaltic source with a relatively high Sr/Y, while lower Sr/Y rocks formed by shallower (1.0 GPa) melting of similar sources. Comparison with the Archaean TTG suite highlights the heterogeneity of the TTGs, whose composition spreads the whole combined range of HSA and Archaean adakites, pointing to a diversity of sources and processes

Resource Assessment of the In-Place and Potentially Recoverable Deep Natural Gas Resource of the Onshore Interior Salt Basins, North Central and Northeastern Gulf of Mexico

Energy Technology Data Exchange (ETDEWEB)

Ernest A. Mancini; Paul Aharon; Donald A. Goddard; Roger Barnaby

2005-10-28

The principal research effort for Year 2 of the project has been petroleum system characterization and modeling. Understanding the burial, thermal maturation, and hydrocarbon expulsion histories of the strata in the onshore interior salt basins of the North Central and Northeastern Gulf of Mexico areas is important in hydrocarbon resource assessment. The underburden and overburden rocks in these basins and subbasins are a product of their rift-related geohistory. Petroleum source rock analysis and initial thermal maturation and hydrocarbon expulsion modeling indicated that an effective regional petroleum source rock in the onshore interior salt basins and subbasins, the North Louisiana Salt Basin, Mississippi Interior Salt Basin, Manila Subbasin and Conecuh Subbasin, was Upper Jurassic Smackover lime mudstone. The initial modeling also indicated that hydrocarbon generation and expulsion were initiated in the Early Cretaceous and continued into the Tertiary in the North Louisiana Salt Basin and the Mississippi Interior Salt Basin and that hydrocarbon generation and expulsion were initiated in the Late Cretaceous and continued into the Tertiary in the Manila Subbasin and Conecuh Subbasin. Refined thermal maturation and hydrocarbon expulsion modeling and additional petroleum source rock analysis have confirmed that the major source rock in the onshore interior salt basins and subbasins is Upper Jurassic Smackover lime mudstone. Hydrocarbon generation and expulsion were initiated in the Early to Late Cretaceous and continued into the Tertiary.

Concepts of flow in fractured rocks

International Nuclear Information System (INIS)

Black, J.H.

1989-01-01

The role of well testing is considered in the context of tracer tests in fractured rock. It is shown that the important information required by a tracer test includes not just the hydrogeological parameters (transmissivity and storage), but also the geometry of flow. This is usually implicit in well testing, perhaps because the tests are generally interpretationally insensitive to variations in flow geometry. It is also argued that both well and tracer tests change their flow geometry during their lifetime. They often start as pipe flow near a well and change to large scale, almost spherical, flow after long periods of time. The duration of a tracer test is compared with that of a well test and is found to reach an equivalent duration (of dimensionless time) that is at least 10 4 times longer. Care should be exercised in transposing flow geometries derived from mature well tests on to tracer tests which are not similar in dimensionless time. Finally, a 'sinusoidal flow test' is outlined which has prompted a new way of looking at well tests in terms of their flow geometry. The new analysis involves 'partial dimension' of flow and is probably highly appropriate to fissured rocks. Fissured rocks have, for too long, been seen as a regular system of planar, fully transmissive fissures. (author). 12 refs, 4 figs, 1 tab

The oil potential of the BM-J-2 block, Jequitinhonha basin, Brazil: the integrated study of the basin analysis and modeling of petroleum system; Potencial petrolifero do Bloco BM-J-2, Bacia de Jequitinhonha, Brasil: um estudo integrado de analise de bacia e modelagem de sistemas petroliferos

Energy Technology Data Exchange (ETDEWEB)

Porto, Roberto; Braga, Jose A.E.; Saito, Makoto; Cortez, Marcella; Ponte Filho, Francisco C.; Romao, Felipe [Queiroz Galvao Perfuracoes S.A., Rio de Janeiro, RJ (Brazil); Goncalves, Felix T.T. [PGT-Petroleum Geoscience Technology Ltd., Rio de Janeiro, RJ (Brazil)

2004-07-01

The integration of all available geochemical data from this and adjoining blocks (BM-J-1 e BM-J-3) Jequitinhonha Basin revealed that only the Albian-Turonian and Aptian sections contains potential hydrocarbon source rock intervals. The existence of an oil accumulation (1-BAS-37) represents an unequivocal evidence of the presence of effective source rocks in the Jequitinhonha Basin. The geochemical characteristics of this oil accumulation points to an origin related to petroleum source rocks deposited under a lacustrine/marine restricted (hyper saline) environment. Such characteristics are typical of pre-salt Aptian source rocks in several basins along the Brazilian margin. The pseudo-3D modeling results indicate that the stage of thermal evolution of the base of the rift section attained ranges from early mature (0.6-0.8 Ro) in the structural highs to over mature (up to 2.0% Ro) in the structural lows On the other hand, the potential sources rocks of Albian-Turonian age ranges to immature to early mature throughout the block. The modeling results also points to the existence of two distinct hydrocarbon 'kitchens': one located in the easternmost portion of the block (slope/deep water area) and the other in a structural low located in the shallow platform area. The main phase of petroleum expulsion ranged from Late Cretaceous/Paleogene in the platform area. Probabilistic simulations has estimated migrated oils and gas volumes around 507 MMbbl and 20 billion cubic meters, respectively. (author)

A Rock Mechanics and Coupled Hydro mechanical Analysis of Geological Repository of High Level Nuclear Waste in Fractured Rocks

International Nuclear Information System (INIS)

Min, Kibok

2011-01-01

This paper introduces a few case studies on fractured hard rock based on geological data from Sweden, Korea is one of a few countries where crystalline rock is the most promising rock formation as a candidate site of geological repository of high level nuclear waste. Despite the progress made in the area of rock mechanics and coupled hydro mechanics, extensive site specific study on multiple candidate sites is essential in order to choose the optimal site. For many countries concerned about the safe isolation of nuclear wastes from the biosphere, disposal in a deep geological formation is considered an attractive option. In geological repository, thermal loading continuously disturbs the repository system in addition to disturbances a recent development in rock mechanics and coupled hydro mechanical study using DFN(Discrete Fracture Network) - DEM(Discrete Element Method) approach mainly applied in hard, crystalline rock containing numerous fracture which are main sources of deformation and groundwater flow

Maturity and maturity models in lean construction

Directory of Open Access Journals (Sweden)

Claus Nesensohn

2014-03-01

Full Text Available In recent years there has been an increasing interest in maturity models in management-related disciplines; which reflects a growing recognition that becoming more mature and having a model to guide the route to maturity can help organisations in managing major transformational change. Lean Construction (LC is an increasingly important improvement approach that organisations seek to embed. This study explores how to apply the maturity models to LC. Hence the attitudes, opinions and experiences of key industry informants with high levels of knowledge of LC were investigated. To achieve this, a review of maturity models was conducted, and data for the analysis was collected through a sequential process involving three methods. First a group interview with seven key informants. Second a follow up discussion with the same individuals to investigate some of the issues raised in more depth. Third an online discussion held via LinkedIn in which members shared their views on some of the results. Overall, we found that there is a lack of common understanding as to what maturity means in LC, though there is general agreement that the concept of maturity is a suitable one to reflect the path of evolution for LC within organisations.

Hot dry rock heat mining

International Nuclear Information System (INIS)

Duchane, D.V.

1992-01-01

Geothermal energy utilizing fluids from natural sources is currently exploited on a commercial scale at sites around the world. A much greater geothermal resource exists, however, in the form of hot rock at depth which is essentially dry. This hot dry rock (HDR) resource is found almost everywhere, but the depth at which usefully high temperatures are reached varies from place to place. The technology to mine the thermal energy from HDR has been under development for a number of years. Using techniques adapted from the petroleum industry, water is pumped at high pressure down an injection well to a region of usefully hot rock. The pressure forces open natural joints to form a reservoir consisting of a small amount of water dispensed in a large volume of hot rock. This reservoir is tapped by second well located at some distance from the first, and the heated water is brought to the surface where its thermal energy is extracted. The same water is then recirculated to mine more heat. Economic studies have indicated that it may be possible to produce electricity at competitive prices today in regions where hot rock is found relatively close to the surface

Primordial Pb, radiogenic Pb and lunar soil maturity

International Nuclear Information System (INIS)

Reed, G.W. Jr.; Jovanovic, S.

1978-01-01

The soil maturity index I/sub s//FeO does not apply to either 204 Pb/sub r/ or C/sub hyd/; both are directly correlated with the submicron Fe 0 (I/sub s/) content. They act as an index of soil maturity which is independent of soil composition. In contrast to primordial Pb, radiogenic Pb is lost during soil maturation. Radiogenic Pb is present in mineral grains and may be lost by solar wind sputtering (or volatilization) and not resupplied. 204 Pb coating grain surfaces acts as a reservoir to provide the 204 Pb being extracted in the Fe 0 formation process. Venting or some other volatile source may replenish the surface 204 Pb. 1 figure

Some clastic rocks as parent rocks in beech forests of Brezovica - Južni Kučaj

Directory of Open Access Journals (Sweden)

Joksimović Vesna

2003-01-01

Full Text Available On the large forest areas, where the measures of soil quality improvement are absent or rarely undertaken, the rocks are the sources of a great number of elements in plant nutrition and one of the factors affecting the contents of some elements in plants. The aim of the study is to determine the differences in the contents of Cu, Zn, Mn, Ni, Fe, Cd, Co, Pb and Cr in the beech leaves developed in the same climate conditions, on morphologically similar terrains, composed of different types of sedimentary rocks. This paper presents the study results of the contents of the above elements in argillites, sandstones (grauwackes and microconglomerates occurring as the parent rocks in high beech forests in the region of GJ Bogovina (Brezovica Južni Kučaj and in the leaves of beech developed on these rocks.

Pore Type Classification on Carbonate Reservoir in Offshore Sarawak using Rock Physics Model and Rock Digital Images

International Nuclear Information System (INIS)

Lubis, L A; Harith, Z Z T

2014-01-01

It has been recognized that carbonate reservoirs are one of the biggest sources of hydrocarbon. Clearly, the evaluation of these reservoirs is important and critical. For rigorous reservoir characterization and performance prediction from geophysical measurements, the exact interpretation of geophysical response of different carbonate pore types is crucial. Yet, the characterization of carbonate reservoir rocks is difficult due to their complex pore systems. The significant diagenesis process and complex depositional environment makes pore systems in carbonates far more complicated than in clastics. Therefore, it is difficult to establish rock physics model for carbonate rock type. In this paper, we evaluate the possible rock physics model of 20 core plugs of a Miocene carbonate platform in Central Luconia, Sarawak. The published laboratory data of this area were used as an input to create the carbonate rock physics models. The elastic properties were analyzed to examine the validity of an existing analytical carbonate rock physics model. We integrate the Xu-Payne Differential Effective Medium (DEM) Model and the elastic modulus which was simulated from a digital carbonate rock image using Finite Element Modeling. The results of this integration matched well for the separation of carbonate pore types and sonic P-wave velocity obtained from laboratory measurement. Thus, the results of this study show that the integration of rock digital image and theoretical rock physics might improve the elastic properties prediction and useful for more advance geophysical techniques (e.g. Seismic Inversion) of carbonate reservoir in Sarawak

A Systematic Literature Review of Agile Maturity Model Research

Directory of Open Access Journals (Sweden)

Vaughan Henriques

2017-02-01

Full Text Available Background/Aim/Purpose: A commonly implemented software process improvement framework is the capability maturity model integrated (CMMI. Existing literature indicates higher levels of CMMI maturity could result in a loss of agility due to its organizational focus. To maintain agility, research has focussed attention on agile maturity models. The objective of this paper is to find the common research themes and conclusions in agile maturity model research. Methodology: This research adopts a systematic approach to agile maturity model research, using Google Scholar, Science Direct, and IEEE Xplore as sources. In total 531 articles were initially found matching the search criteria, which was filtered to 39 articles by applying specific exclusion criteria. Contribution:: The article highlights the trends in agile maturity model research, specifically bringing to light the lack of research providing validation of such models. Findings: Two major themes emerge, being the coexistence of agile and CMMI and the development of agile principle based maturity models. The research trend indicates an increase in agile maturity model articles, particularly in the latter half of the last decade, with concentrations of research coinciding with version updates of CMMI. While there is general consensus around higher CMMI maturity levels being incompatible with true agility, there is evidence of the two coexisting when agile is introduced into already highly matured environments. Future Research:\tFuture research direction for this topic should include how to attain higher levels of CMMI maturity using only agile methods, how governance is addressed in agile environments, and whether existing agile maturity models relate to improved project success.

Task 8: Evaluation of hydrocarbon potential

International Nuclear Information System (INIS)

Cashman, P.H.; Trexler, J.H. Jr.

1994-01-01

Our studies focus on the stratigraphy of Late Devonian to early Pennsylvanian rocks at the NTS, because these are the best potential hydrocarbon source rocks in the vicinity of Yucca Mountain. In the last year, our stratigraphic studies have broadened to include the regional context for both the Chainman and the Eleana formations. New age data based on biostratigraphy constrain the age ranges of both Chainman and Eleana; accurate and reliable ages are essential for regional correlation and for regional paleogeographic reconstructions. Source rock analyses throughout the Chainman establish whether these rocks contained adequate organic material to generate hydrocarbons. Maturation analyses of samples from the Chainman determine whether the temperature history has been suitable for the generation of liquid hydrocarbons. Structural studies are aimed at defining the deformation histories and present position of the different packages of Devonian - Pennsylvanian rocks. This report summarizes new results of our structural, stratigraphic and hydrocarbon source rock potential studies at the Nevada Test Site and vicinity. Stratigraphy is considered first, with the Chainman Shale and Eleana Formation discussed separately. New biostratigraphic results are included in this section. New results from our structural studies are summarized next, followed by source rock and maturation analyses of the Chainman Shale. Directions for future work are included where appropriate

A COMPARISON OF MAJOR ELEMENTS BETWEEN MARINE SEDIMENTS AND IGNEOUS ROCKS: AS A BASIC DETERMINATION OF THE SEDIMENT SOURCE AT UJUNG PENYUSUK WATERS, NORTH BANGKA,BANGKA BELITUNG PROVINCE

Directory of Open Access Journals (Sweden)

Ediar Usman

2017-07-01

Full Text Available Three igneous rock samples from the coast and five sediments from the marine of Ujung Penyusuk Waters have been used for chemistry analysis as the basic determination of sediment source. The result of chemistry analysis shows that the major element with relatively same pattern. In the igneous rock samples, the result of chemistry analysis shows the SiO2 ranges between 72.3 - 76.8%, Al2O3 (9.64 - 11.64%, and Fe2O3 ( 2.08 - 2.18%. In the marine sediment, the content of SiO2 is between 62.2 and 66.5%, Al2O3 (2.93 - 3.63% and Fe2O3 (21.19 - 24.40%. Other elements such as CaO, MgO, K2O, Na2O and TiO2 are relatively similar values in all samples. The difference of element content in marine sediment and coastal igneous rock occurs in Al2O3 and Fe2O3. The Al2O3 is small in marine sediment while the Fe2O3 is higher compared to igneous rocks. Decreasing of the Al2O3 (kaolinite in the marine sediment is caused by the character of the Al2O3 that was derived from quartz rich of igneous rocks forming kaolinite. It was than deposited in the sea floor. Increasing of the Fe2O3 in marine sediment is caused by addition reaction of the Fe from the sea. Generally, the content of the SiO2 (quartz in igneous rock and marine sediment belongs to the same group source that is acid igneous rock. The SiO2 in the sediment belongs to a group of granitoid.

Effect of organic matter properties, clay mineral type and thermal maturity on gas adsorption in organic-rich shale systems

Science.gov (United States)

Zhang, Tongwei; Ellis, Geoffrey S.; Ruppel, Stephen C.; Milliken, Kitty; Lewan, Mike; Sun, Xun; Baez, Luis; Beeney, Ken; Sonnenberg, Steve

2013-01-01

A series of CH4 adsorption experiments on natural organic-rich shales, isolated kerogen, clay-rich rocks, and artificially matured Woodford Shale samples were conducted under dry conditions. Our results indicate that physisorption is a dominant process for CH4 sorption, both on organic-rich shales and clay minerals. The Brunauer–Emmett–Teller (BET) surface area of the investigated samples is linearly correlated with the CH4 sorption capacity in both organic-rich shales and clay-rich rocks. The presence of organic matter is a primary control on gas adsorption in shale-gas systems, and the gas-sorption capacity is determined by total organic carbon (TOC) content, organic-matter type, and thermal maturity. A large number of nanopores, in the 2–50 nm size range, were created during organic-matter thermal decomposition, and they significantly contributed to the surface area. Consequently, methane-sorption capacity increases with increasing thermal maturity due to the presence of nanopores produced during organic-matter decomposition. Furthermore, CH4 sorption on clay minerals is mainly controlled by the type of clay mineral present. In terms of relative CH4 sorption capacity: montmorillonite ≫ illite – smectite mixed layer > kaolinite > chlorite > illite. The effect of rock properties (organic matter content, type, maturity, and clay minerals) on CH4 adsorption can be quantified with the heat of adsorption and the standard entropy, which are determined from adsorption isotherms at different temperatures. For clay-mineral rich rocks, the heat of adsorption (q) ranges from 9.4 to 16.6 kJ/mol. These values are considerably smaller than those for CH4 adsorption on kerogen (21.9–28 kJ/mol) and organic-rich shales (15.1–18.4 kJ/mol). The standard entropy (Δs°) ranges from -64.8 to -79.5 J/mol/K for clay minerals, -68.1 to -111.3 J/mol/K for kerogen, and -76.0 to -84.6 J/mol/K for organic-rich shales. The affinity of CH4 molecules for sorption on organic matter

Rho-GTPase effector ROCK phosphorylates cofilin in actin-meditated cytokinesis during mouse oocyte meiosis.

Science.gov (United States)

Duan, Xing; Liu, Jun; Dai, Xiao-Xin; Liu, Hong-Lin; Cui, Xiang-Shun; Kim, Nam-Hyung; Wang, Zhen-Bo; Wang, Qiang; Sun, Shao-Chen

2014-02-01

During oocyte meiosis, a spindle forms in the central cytoplasm and migrates to the cortex. Subsequently, the oocyte extrudes a small body and forms a highly polarized egg; this process is regulated primarily by actin. ROCK is a Rho-GTPase effector that is involved in various cellular functions, such as stress fiber formation, cell migration, tumor cell invasion, and cell motility. In this study, we investigated possible roles for ROCK in mouse oocyte meiosis. ROCK was localized around spindles after germinal vesicle breakdown and was colocalized with cytoplasmic actin and mitochondria. Disrupting ROCK activity by RNAi or an inhibitor resulted in cell cycle progression and polar body extrusion failure. Time-lapse microscopy showed that this may have been due to spindle migration and cytokinesis defects, as chromosomes segregated but failed to extrude a polar body and then realigned. Actin expression at oocyte membranes and in cytoplasm was significantly decreased after these treatments. Actin caps were also disrupted, which was confirmed by a failure to form cortical granule-free domains. The mitochondrial distribution was also disrupted, which indicated that mitochondria were involved in the ROCK-mediated actin assembly. In addition, the phosphorylation levels of Cofilin, a downstream molecule of ROCK, decreased after disrupting ROCK activity. Thus, our results indicated that a ROCK-Cofilin-actin pathway regulated meiotic spindle migration and cytokinesis during mouse oocyte maturation.

Physical activity and biological maturation: a systematic review

Directory of Open Access Journals (Sweden)

Eliane Denise Araújo Bacil

2015-03-01

Full Text Available OBJECTIVE: To analyze the association between physical activity (PA and biological maturation in children and adolescents. DATA SOURCE: We performed a systematic review in April 2013 in the electronic databases of PubMed/MEDLINE, SportDiscus, Web of Science and LILACS without time restrictions. A total of 628 potentially relevant articles were identified and 10 met the inclusion criteria for this review: cross-sectional or longitudinal studies, published in Portuguese, English or Spanish, with schoolchildren aged 9-15 years old of both genders. DATA SYNTHESIS: Despite the heterogeneity of the studies, there was an inverse association between PA and biological maturation. PA decreases with increased biological and chronological age in both genders. Boys tend to be more physically active than girls; however, when controlling for biological age, the gender differences disappear. The association between PA and timing of maturation varies between the genders. Variation in the timing of biological maturation affects the tracking of PA in early adolescent girls. This review suggests that mediators (BMI, depression, low self-esteem, and concerns about body weight can explain the association between PA and biological maturation. CONCLUSIONS: There is an association between PA and biological maturation. PA decreases with increasing biological age with no differences between genders. As for the timing of biological maturation, this association varies between genders.

Relating rock avalanche morphology to emplacement processes

Science.gov (United States)

Dufresne, Anja; Prager, Christoph; Bösmeier, Annette

2015-04-01

The morphology, structure and sedimentological characteristics of rock avalanche deposits reflect both internal emplacement processes and external influences, such as runout path characteristics. The latter is mainly predisposed by topography, substrate types, and hydrogeological conditions. Additionally, the geological setting at the source slope controls, e.g. the spatial distribution of accumulated lithologies and hence material property-related changes in morphology, or the maximum clast size and amount of fines of different lithological units. The Holocene Tschirgant rock avalanche (Tyrol, Austria) resulted from failure of an intensely deformed carbonate rock mass on the southeast face of a 2,370-m-high mountain ridge. The initially sliding rock mass rapidly fragmented as it moved towards the floor of the Inn River valley. Part of the 200-250 x 106 m3 (Patzelt 2012) rock avalanche debris collided with and moved around an opposing bedrock ridge and flowed into the Ötz valley, reaching up to 6.3 km from source. Where the Tschirgant rock avalanche spread freely it formed longitudinal ridges aligned along motion direction as well as smaller hummocks. Encountering high topography, it left runup ridges, fallback patterns (i.e. secondary collapse), and compressional morphology (successively elevated, transverse ridges). Further evidence for the mechanical landslide behaviour is given by large volumes of mobilized valley-fill sediments (polymict gravels and sands). These sediments indicate both shearing and compressional faulting within the rock avalanche mass (forming their own morphological units through, e.g. in situ bulldozing or as distinctly different hummocky terrain), but also indicate extension of the spreading landslide mass (i.e. intercalated/injected gravels encountered mainly in morphological depressions between hummocks). Further influences on its morphology are given by the different lithological units. E.g. the transition from massive dolomite

Technical evaluation of the proposed changes in the technical specifications for emergency power sources for the Big Rock Point nuclear power plant

International Nuclear Information System (INIS)

Latorre, V.R.

1979-12-01

The technical evaluation is presented for the proposed changes to the Technical Specifications for emergency power sources for the Big Rock Point nuclear power plant. The criteria used to evaluate the acceptability of the changes include those delineated in IEEE Std-308-1974, and IEEE Std-450-1975 as endorsed by US NRC Regulatory Guide 1.129

Advancement in application of diamondoids on organic geochemistry

Directory of Open Access Journals (Sweden)

Anlai Ma

2016-08-01

Full Text Available Diamondoids occur in all kinds of fossil fuels. Due to peculiar cage molecular structures, diamondoids have been widely used in the maturity assessment of high mature to over-mature oils as well as source rocks since the 1990s. New advancements in maturity, oil-cracking, oil mixing, oil biodegradation, organic facies, TSR, gas washing, migration, and oil spill identification using diamondoids during the 21st century will be further discussed in this paper; the origin and possible forming mechanisms of diamondoids are also explained. Owing to the vagueness of the origin of diamondoid, the results of the maturity and oil cracking among researchers brought about great differences. It is suggested that the research of the evolution of diamondoid in different type oils and source rocks are beneficial when applied in organic geochemistry, especially for the depth limits for the deep reservoirs.

Characteristics of mesozoic magmatic rocks in western Zhejiang and their relation with uranium mineralization

International Nuclear Information System (INIS)

Zhou Jiazhi

2000-01-01

The author summarizes characteristics of Mesozoic (Yangshanian Period) acid-intermediate volcanics, sub-volcanics and basic intrusive from aspects of formation time of rock series, petrogenic sequence, chemical composition, rock -controlling factors and petrogenic environments. It is suggested that these rocks were originated from different source areas of crust and mantle. Based on the time-space relation between different types uranium deposits and magmatic rocks, the author proposes that: the earlier stage (Earlier Cretaceous) U-hematite ores were originated from acid volcanic magmatism of crustal source, but the later stage (Late Cretaceous) pitchblende-polymetallic sulfide and pitchblende-purple fluorite rich ores were derived from basic magmatism of mantle source. Finally, the author proposes prospecting criteria of the above two types of uranium deposits

Failure Mechanism of Rock Bridge Based on Acoustic Emission Technique

Directory of Open Access Journals (Sweden)

Guoqing Chen

2015-01-01

Full Text Available Acoustic emission (AE technique is widely used in various fields as a reliable nondestructive examination technology. Two experimental tests were carried out in a rock mechanics laboratory, which include (1 small scale direct shear tests of rock bridge with different lengths and (2 large scale landslide model with locked section. The relationship of AE event count and record time was analyzed during the tests. The AE source location technology and comparative analysis with its actual failure model were done. It can be found that whether it is small scale test or large scale landslide model test, AE technique accurately located the AE source point, which reflected the failure generation and expansion of internal cracks in rock samples. Large scale landslide model with locked section test showed that rock bridge in rocky slope has typical brittle failure behavior. The two tests based on AE technique well revealed the rock failure mechanism in rocky slope and clarified the cause of high speed and long distance sliding of rocky slope.

Demonstration of a Fractured Rock Geophysical Toolbox (FRGT) for Characterization and Monitoring of DNAPL Biodegradation in Fractured Rock Aquifers

Science.gov (United States)

2015-09-29

is characterized by dark gray slate or phyllite, alternating with thin layers of light gray siltstone or sandstone . Table 1 summarizes the primary...sedimentary rocks of the Newark Basin. Competent rocks are primarily mudstones and sandstones of the Lockatong and Stockton Formations. Fill, weathered silt... sandstone , and characterized by water bearing bedding plane fractures. An array of open boreholes in the source area that were drilled for the 2002

Distribution and evolution of Zn, Cd, and Pb in Apollo 16 regolith samples and the average U-Pb ages of the parent rocks

Science.gov (United States)

Cirlin, E. H.; Housley, R. M.

1982-01-01

The concentration of surface (low temperature site) and interior (high temperature site) Cd, Zn, and Pb in 13 Apollo 16 highland fines samples, pristine rock 65325, and mare fines sample 75081 were analyzed directly from the thermal release profiles obtained by flameless atomic absorption technique (FLAA). Cd and Zn in pristine ferroan anothosite 65325, anorthositic grains of the most mature fines 65701, and basaltic rock fragments of mare fines 75081 were almost all surface Cd and Zn indicating that most volatiles were deposited on the surfaces of vugs, vesicles and microcracks during the initial cooling process. A considerable amount of interior Cd and Zn was observed in agglutinates. This result suggests that high temperature site interior volatiles originate from entrapment during the lunar maturation processes. Interior Cd found in the most mature fines sample 65701 was only about 15% of the total Cd in the sample. Interior Pb present in Apollo 16 fines samples went up to 60%. From our Cd studies we can assume that this interior Pb in highland fines samples is largely due to the radiogenic decay which occurred after the redistribution of the volatiles took place. We obtained an average age of 4.0 b.y. for the parent rocks of Apollo 16 highland regolith from our interior Pb analyses.

The origin of groundwater salinity in granitic rocks: identification and characterisation of chloride sources

International Nuclear Information System (INIS)

Savoye, Sebastien

1998-01-01

This research thesis aims at clearly identifying the possible origins of chlorine in solution in underground waters in a granitic environment, and is thus a first step in the prediction of concentration of dissolved compounds in waters in crystalline environment, with respect to the geological context. In a first part, the author proposes a synthetic and critical overview of knowledge and previous studies: definition of the term 'salinity', presentation of geochemical tracers, presentation of available data on potential chlorine sources in granitic rocks. The author then describes the experimental protocols and studied sites, reports results of the characterisation of different chlorine tanks performed on samples from each studied site. Based on mass assessment calculations and on the use of tracers, the author finally discusses the contribution of each of the chlorine tanks to the salinity of underground waters [fr

Water - rock interaction in different rock environments

International Nuclear Information System (INIS)

Lamminen, S.

1995-01-01

The study assesses the groundwater geochemistry and geological environment of 44 study sites for radioactive waste disposal. Initially, the study sites were divided by rock type into 5 groups: (1) acid - intermediate rocks, (2) mafic - ultramafic rocks, (3) gabbros, amphibolites and gneisses that contain calc-silicate (skarn) rocks, (4) carbonates and (5) sandstones. Separate assessments are made of acid - intermediate plutonic rocks and of a subgroup that comprises migmatites, granite and mica gneiss. These all belong to the group of acid - intermediate rocks. Within the mafic -ultramafic rock group, a subgroup that comprises mafic - ultramafic plutonic rocks, serpentinites, mafic - ultramafic volcanic rocks and volcanic - sedimentary schists is also evaluated separately. Bedrock groundwaters are classified by their concentration of total dissolved solids as fresh, brackish, saline, strongly saline and brine-class groundwaters. (75 refs., 24 figs., 3 tabs.)

Angola: source rock control for Lower Congo Coastal and Kwanza Basin petroleum systems

Energy Technology Data Exchange (ETDEWEB)

Burwood, R. [Fina Exploration Ltd, Epsom (United Kingdom)

1999-07-01

The purpose of this paper is to provide an overview of petroleum occurrence and provenance for the 1000 km West African Atlantic Margin from Cabinda to mid-Angola. Over this margin the Lower Congo Coastal and Kwanza provinces cumulatively account for reserves of c. 6 gigabarrels oil recoverable (GBOR). These are dominantly reservoired in Pinda carbonate traps of the former basin. However, with production from a range of aggradational wedge, carbonate platform and pre-salt reservoirs, a diversity in oil character presupposes complex hydrocarbon habitats charged by multiple sourcing. Each of these two major Atlantic margin salt basins constitutes a different, source rock driven, hydrocarbon habitat. As classic passive margin pull-apart basins, Early Cretaceous initiated rift events (Pre-rift, Syn-rift I, II, etc.) evolved into the drift phase opening of the southern Atlantic. A striking feature of this progression was widespread evaporite deposition of the Aptian Loeme salt. This separates two distinct sedimentary and tectonic domains of the Pre- and Post-Salt. The core Lower Congo Coastal habitat is dominated by the Pre-Salt Bucomazi Formation sourced 'poly' petroleum system. These lacustrine, often super-rich, sediments reveal considerable organofacies variation between their basin fill (Syn-rift I) and sheet drape (Syn-rift II) development, accounting for the compositional diversity in their progenic petroleums. Of crucial impact is a cognate diversity in their kerogen kinetic behaviour. This controls the conditions and timing of generation and realization of charge potential. With the Lower Congo Coastal habitat extending southwards towards the Ambriz Spur, the Bucomazi facies proper appears restricted to the northern and deeper proto-lake trend. Over the more weakly subsident margins such troughs host inferior sheet drape potential. Elswhere, Upper Cretaceous-Palaeogene marine clastic Iabe Formation sourced petroleum systems are hydrocarbon productive

The effect of maturation on the configurations of acyclic isoprenoid acids in sediments

Science.gov (United States)

Mackenzie, A. S.; Patience, R. L.; Yon, D. A.; Maxwell, J. R.

1982-05-01

Within a variety of sedimentary rocks of differing maturity, the configurations of a suite of acyclic isoprenoid acids have been examined by gas Chromatographic (in a few cases also by combined gas chromatography-mass spectrometry) analysis of their diastereoisomeric methyl and (-)-menthyl esters. The samples include the Eocene Messel (Germany) and Green River (U.S.) shales, the Permian Irati shale (Brazil) and a number of Lower Toarcian shales from the Paris Basin. The isomer distributions show that isomerisation occurs at the chiral centres with increasing maturation (to increase the number of isomers) and that the rate of isomerisation increases for centres (C-2,C-3) closest to the carboxyl group. These results suggest that adsorption of the carboxyl group to a catalyst surface may control the isomerisation rates by way of access to the catalyst.

Effects of Crocin Supplementation during In Vitro Maturation of Mouse Oocytes on Glutathione Synthesis and Cytoplasmic Maturation

Directory of Open Access Journals (Sweden)

Elham Mokhber Maleki

2016-05-01

Full Text Available Background: Crocin is an active ingredient of saffron (Crocus sativus L. and its antioxidant properties have been previously investigated. This carotenoid scavenges free radicals and stimulates glutathione (GSH synthesis; consequently, it may protect cells against oxidative stress. The aim of this research is to protect oocytes from oxidative stress by the addition of a natural source antioxidant. Materials and Methods: In the present in vitro experimental study, we collected cumulus oocyte complexes (COCs from mouse ovaries of euthanized, 6-8 week-old female Naval Medical Research Institute (NMRI mice. Oocytes were subjected to in vitro maturation (IVM in the presence of either crocin (5 or 10 μg/ml, 5 mM buthionine-[S-R]- sulfoximine (BSO, or the combination of crocin plus BSO. Oocytes that matured in vitro in a medium without crocin or BSO supplements were considered as controls. Following 16-18 hours of IVM, matured oocytes (n=631 were fertilized by capacitated sperm from NMRI male mice, and cultured in vitro for up to 96 hours to assess preimplantation embryonic development. The levels of GSH in metaphase II (MII oocytes after IVM (n=240 were also assessed by the 5, 5-dithio-bis (2-nitrobenzoic acid (DTNB-GSH reductase recycling assay. Results: Supplementation of IVM media with 10 μg/ml crocin significantly (P<0.05 increased nuclear maturation, preimplantation development and GSH concentrations compared with the control group. Maturation of oocytes in IVM medium supplemented with BSO alone or the combination of 5 μg/ml crocin and BSO drastically decreased GSH concentrations and subsequently resulted in low rates of maturation, fertilization and blastocyst development. However, the combination of 10 μg/ml crocin with 5 mM BSO increased the level of nuclear maturation which was comparable to the control group. Conclusion: Supplementation of IVM media with crocin can improve nuclear maturation rates and subsequent developmental potential

Organic richness and organic matter quality studies of source rocks ...

African Journals Online (AJOL)

The hydrocarbon potential of the Upper Cretaceous units (Maastrichtian Mamu Formation) exposed at Imiegba and environs of the Benin Flank, Western Anambra Basin was assessed by Total Organic Carbon (TOC) and Rock-Eval Pyrolysis Analyses. The investigated sections of the Mamu Formation consist of dark grey to ...

Determining the Accuracy of Paleomagnetic Remanence and High-Resolution Chronostratigraphy for Sedimentary Rocks using Rock Magnetics

Science.gov (United States)

Kodama, K. P.

2017-12-01

The talk will consider two broad topics in rock magnetism and paleomagnetism: the accuracy of paleomagnetic remanence and the use of rock magnetics to measure geologic time in sedimentary sequences. The accuracy of the inclination recorded by sedimentary rocks is crucial to paleogeographic reconstructions. Laboratory compaction experiments show that inclination shallows on the order of 10˚-15˚. Corrections to the inclination can be made using the effects of compaction on the directional distribution of secular variation recorded by sediments or the anisotropy of the magnetic grains carrying the ancient remanence. A summary of all the compaction correction studies as of 2012 shows that 85% of sedimentary rocks studied have enjoyed some amount of inclination shallowing. Future work should also consider the effect of grain-scale strain on paleomagnetic remanence. High resolution chronostratigraphy can be assigned to a sedimentary sequence using rock magnetics to detect astronomically-forced climate cycles. The power of the technique is relatively quick, non-destructive measurements, the objective identification of the cycles compared to facies interpretations, and the sensitivity of rock magnetics to subtle changes in sedimentary source. An example of this technique comes from using rock magnetics to identify astronomically-forced climate cycles in three globally distributed occurrences of the Shuram carbon isotope excursion. The Shuram excursion may record the oxidation of the world ocean in the Ediacaran, just before the Cambrian explosion of metazoans. Using rock magnetic cyclostratigraphy, the excursion is shown to have the same duration (8-9 Myr) in southern California, south China and south Australia. Magnetostratigraphy of the rocks carrying the excursion in California and Australia shows a reversed to normal geomagnetic field polarity transition at the excursion's nadir, thus supporting the synchroneity of the excursion globally. Both results point to a

Rock mass mechanical property estimations for the Yucca Mountain Site Characterization Project

International Nuclear Information System (INIS)

Lin, M.; Hardy, M.P.; Bauer, S.J.

1993-06-01

Rock mass mechanical properties are important in the design of drifts and ramps. These properties are used in evaluations of the impacts of thermomechanical loading of potential host rock within the Yucca Mountain Site Characterization Project. Representative intact rock and joint mechanical properties were selected for welded and nonwelded tuffs from the currently available data sources. Rock mass qualities were then estimated using both the Norwegian Geotechnical Institute (Q) and Geomechanics Rating (RMR) systems. Rock mass mechanical properties were developed based on estimates of rock mass quality, the current knowledge of intact properties, and fracture/joint characteristics. Empirical relationships developed to correlate the rock mass quality indices and the rock mass mechanical properties were then used to estimate the range of rock mass mechanical properties

Remarks on some rock neutron parameters

International Nuclear Information System (INIS)

Czubek, J.A.

1984-01-01

A method to calculate the thermal neutron parameters of rocks is given in the paper. It is based on a proper energy averaging of cross-sections for all rock matrix and rock saturating liquid constituents. The diffusion lengths in different lithologies in function of the variable rock porosity have been calculated. An influence of the thermal neutron spectrum on the shape of the porosity calibration curves for the dual spacing neutron method is shown. Magmatic rocks as a possible source of geothermal energy are now becoming a target of neutron loggings for the porosity determination. Here the knowledge of the slowing-down lengths is of great importance in the problem of the estimation of the calibration curves. A semi-analytical approach to get this parameter is given in the paper. It was found, as far as concerns the slowing-down of fast neutrons, that all magmatic rocks behave as sandstone with, however, different content of bound water in the rock matrix and different rock matrix density. Some neutron methods are based on the detection of epithermal neutrons. For theoretical considerations it is important to know the physical meaning of the registered signal. From the discussion of experimental data reported in the literature it seems that it is the slowing-down density that is the physical quantity being measured. This conclusion has a very important practical implication - the porosity calibration curves depend upon the slowing-down length alone and are independent of the slowing-down cross-section for epithermal neutrons

Rb-Sr geochronology of the rocks of the Himalayas, Eastern Nepal, (1)

International Nuclear Information System (INIS)

Kai, Kunio

1981-01-01

Rb-Sr isotopic measurements were carried out for whole rock and small sliced rock from the Himalayan gneiss which constitutes the metamorphosed basement of the Tethyan sediments. The results of the measurements on whole rock from the Barun migmatite, the Barun gneiss and the Irkhua gneiss indicate that complete Sr isotopic redistribution occurred about 520 m.y. ago. This age is interpreted as the time of the regional metamorphism. The analytical results of the small sliced slabs of the Himalayan gneiss indicate that Sr isotopic redistribution occurred among the sliced slabs 33.3 +- 13.2 m.y. ago. This age is interpreted as the time of the metamorphism in the sillimanite-amphibolite facies. The high initial 87 Sr/ 86 Sr ratio of 0.7372 +- 0.0031 from the Barun migmatite of the Himalayan gneiss suggests the Precambrian Origin of the source rocks. The analytical results on the sliced slab of the Barun migmatite indicate that the original age of the rocks is about 800 m.y. The rock is interpreted as the remobilized Precambrian crustal rock. The high initial 87 Sr/ 86 Sr ratio of the Barun gneiss and the Irkhua gneiss of the Himalayan gneiss (0.7234 +- 0.0013) indicates also the Precambrian origin of the source rocks. (author)

Studies on the radiation absorption characteristics of various rocks

International Nuclear Information System (INIS)

Rahman, K.N.; Abdullah, S.A.; Gazzaz, M.A.

1984-05-01

Radiation absorption characteristics of nine different rocks, namely, ferrugenous quartz, metabasalt, larvikite, coarse grained diorite, coarse grained granite, coarse grained alkali granite, marble, quartz mica schist, and metamorphosed rock are studied. The rocks were collected from Jeddah, Makkah, Mina and Taif areas. Special attention was given on the availability, compactness, physical formation and uniform composition in selecting the rocks. The rocks were identified by optical method and their elemental composition determined by chemical analysis. The data were used to calculate the effective atomic numbers, half value layers mass and linear attenuation coefficients. The half value layers and the linear attenuation coefficientsof these rocks were determined experimentally using Am-241, Cs-137,and Co-60 sources. The results are compared with those obtained by theoretical calculations and agrre within 10%. Most of the rocks show much higher radiation attenuation characteristics than the standard concrete. Rocks containing higher percentage of Fe, Ca, Ti, and Mn show much higher radiation absorption characteristics than concrete. Only granites are found to be almost equivalent to concrete. 12 Ref

HEAVY MINERALS IN PLACER DEPOSIT IN SINGKAWANG WATERS, WEST Kalimantan, RELATED TO FELSIC SOURCE ROCK OF ITS COASTAL AREA

Directory of Open Access Journals (Sweden)

Deny Setiady

2017-07-01

Full Text Available Placer deposits are physically accumulated by fluvial and marine processes in coastal area. Thirty six samples were selected from seventy seven samples of seafloor sediment of Singkawang waters. Those samples have been analyzed microscopically for heavy mineral contents. Based on this analysis, the heavy minerals can be divided into four groups: oxyde and hydroxyde, silicate, sulphide, and carbonate. The source of most heavy minerals in the study area is commonly formed by Felsic igneous rock and finally deposited on the seafloor sediments.

Waste-rock interactions in the immediate repository

International Nuclear Information System (INIS)

McCarthy, G.J.

1977-01-01

The high level wastes (HLW's) to be placed underground in rock formations will contain significant amounts of radioactive decay heat for the first hundred-or-so years of isolation. Several physical-chemical changes analogous to natural geochemical processes can occur during this ''thermal period.'' The waste canister can act as a heat source and cause changes in the mineralogy and properties of the surrounding rocks. Geochemically, this is ''contact metamorphism.'' In the event that the canister is corroded and breached, chemical reactions can occur between the HLW, the surrounding rock and possibly the remains of the canister. In a dry repository which has not been backfilled (and thus pressurized) these interactions could be slow at best and with rates decreasing rapidly as the HLW cools. However, significant interactions can occur in years, months or even days under hydrothermal conditions. These conditions could be created by the combination of HLW heat, overburden pressure and water mobilized from the rocks or derived from groundwater intrusion. At the end of the thermal period these interaction products would constitute the actual HLW form (or ''source term'') subject to the low temperature leaching and migration processes under investigation in other laboratories. It is quite possible that these interaction product waste forms will have superior properties compared to the original HLW. Experimental programs initiated at Penn State during the last year aim at determining the nature of any chemical or mineralogical changes in, or interactions between, HLW solids and host rocks under various repository ambients. The accompanying figures describe the simulated HLW forms and the experimental approach and techniques. Studies with basalts as the repository rock are supported by Rockwell Hanford Operations and with shales by the Office of Waste Isolation

Thermal history of the Krishna-Godavari basin, India: Constraints from apatite fission track thermochronology and organic maturity data

Science.gov (United States)

Sahu, Himansu S.; Raab, Matthias J.; Kohn, Barry P.; Gleadow, Andrew J. W.; Bal, Kiron D.

2013-09-01

The Krishna-Godavari (KG) basin, a passive margin Late Carboniferous to Holocene basin along the rifted east coast of India, includes the deltaic and inter-deltaic regions of the Krishna and Godavari rivers onshore and extends into the offshore. It is one of India's premier hydrocarbon-bearing basins. In an attempt to better understand the thermal history of the basin, apatite fission track (AFT) data has been obtained from six exploration wells (five onshore and one offshore). AFT thermal history models as well as other thermal indicators e.g. vitrinite reflectance (VR), Rock-Eval Tmax data reveal that the host rocks are currently at their maximum post-depositional temperatures and that any possible heating related to small-scale tectonism or rifting episodes in the basin bears little significance on the maturation of the sediments. In the case of one borehole (M-1) however, the organic maturity data reveals a period of Oligocene cooling across an unconformity when ∼1000 m of section was eroded due to falling sea-level. This information offers the potential for improved basin modeling of the KG basin.

17,21-Secohopanoic acids, 25-norhopanoic acids, and 28-norhopanoic acids in source rocks and crude oils

Energy Technology Data Exchange (ETDEWEB)

Xueming Pan; Philp, R.P. [University of Oklahoma, Norman, OK (United States). School of Geology and Geophysics

2006-09-15

The presence of three families of hopanoic acids, 17,21-secohopanoic acids, 25-norhopanoic acids, and 28-norhopanoic acids, is discussed. Oils from West Siberia and tar balls from the Seychelles Islands were found to contain relatively high proportions of 17,21-secohopanoic acids. These acids have not been previously reported in any oils or source rocks. A heavily biodegraded West Siberian oil, was found to contain an homologous series of 25-norhopanoic acids co-occurring with the 25-norhopanes as previously reported in only a small number of oils from Campos Basin, Brazil. 28-Norhopanoic acids have been reported in various sediments and extracts of the Monterey Shale, but in this study their occurrence has been extended to oils, degraded oils, and tar balls sourced from the Monterey Shale. The primary purpose herein is to report the occurrence of these acids and possible relationships between the acids and corresponding hydrocarbons. (Author)

Sr isotopes in natural waters: Applications to source characterisation and water-rock interaction in contrasting landscapes

International Nuclear Information System (INIS)

Shand, P.; Darbyshire, D.P.F.; Love, A.J.; Edmunds, W.M.

2009-01-01

Strontium isotopes ( 87 Sr/ 86 Sr) are routinely measured in hydrochemical studies to determine sources and mixing relationships. They have proved particularly useful in determining weathering processes and quantifying end-member mixing processes. A number of routine case studies are presented which highlight that Sr isotopes represent a powerful tool in the geochemists toolbox helping to constrain weathering reactions, weathering rates, flow pathways and mixing scenarios. Differences in methodologies for determining the weathering component in natural environments, inherent differences in weathering rates of different minerals, and mineral heterogeneity often cause difficulties in defining the weathering component of different catchments or aquifer systems. Nevertheless, Sr isotopes are useful when combined with other hydrochemical data, to constrain models of water-rock interaction and mixing as well as geochemical processes such as ion-exchange. This paper presents a summary of recent work by the authors in constraining the sources of waters and weathering processes in surface catchments and aquifers, and indicates cases where Sr isotopes alone are insufficient to solve hydrological problems.

Sr isotopes in natural waters: Applications to source characterisation and water-rock interaction in contrasting landscapes

Energy Technology Data Exchange (ETDEWEB)

Shand, P., E-mail: paul.shand@csiro.au [CSIRO Land and Water/CRC LEME, Private Bag 2, Glen Osmond, SA 5064 (Australia); Darbyshire, D.P.F. [NERC Isotope Geosciences Laboratory, Kingsley Dunham Centre, Keyworth, Nottingham NG12 5GG (United Kingdom); Love, A.J. [Department of Water, Land and Biodiversity Conservation, P.O. Box 2843, Adelaide 5001 (Australia); Edmunds, W.M. [School of Geography, Oxford University Centre for the Environment, South Parks Road, Oxford (United Kingdom)

2009-04-15

Strontium isotopes ({sup 87}Sr/{sup 86}Sr) are routinely measured in hydrochemical studies to determine sources and mixing relationships. They have proved particularly useful in determining weathering processes and quantifying end-member mixing processes. A number of routine case studies are presented which highlight that Sr isotopes represent a powerful tool in the geochemists toolbox helping to constrain weathering reactions, weathering rates, flow pathways and mixing scenarios. Differences in methodologies for determining the weathering component in natural environments, inherent differences in weathering rates of different minerals, and mineral heterogeneity often cause difficulties in defining the weathering component of different catchments or aquifer systems. Nevertheless, Sr isotopes are useful when combined with other hydrochemical data, to constrain models of water-rock interaction and mixing as well as geochemical processes such as ion-exchange. This paper presents a summary of recent work by the authors in constraining the sources of waters and weathering processes in surface catchments and aquifers, and indicates cases where Sr isotopes alone are insufficient to solve hydrological problems.

Isotopic assessment of soil phosphorus fertility and evaluation of rock phosphates as phosphorus sources for plants in subtropical China

International Nuclear Information System (INIS)

Xiong, L.M.; Zhou, Z.G.; Feng, G.L.; Lu, R.K.; Fardeau, J.C.

2002-01-01

Soil phosphorus (P) deficiency is a major factor limiting crop productivity in many tropical and subtropical soils. Due to the acidic nature of these soils, rock phosphate (RP)-based P fertilizers that are cheaper than manufactured water-soluble P fertilizers can be an attractive alternative under certain conditions. Assessment of the efficacy of these alternative P fertilizers and a rational management of local P resources for sustainable agricultural production require an understanding of the dynamics of P in the soil-plant system and the interactions of various P sources in soils and monitoring of soil available P levels. The present work was conducted to test the applicability of the 32 P isotopic kinetic method to assess the soil P fertility status and evaluate the agronomic effectiveness of local rock phosphates in subtropical China. A series of experiments was carried out in the laboratory, greenhouse and field conditions with the following specific objectives: (a) to evaluate the suitability of this isotopic kinetic method in evaluating soil P fertility in 32 soil samples collected across southern China, (b) to test and further develop chemical extraction methods for routine soil P testing, (c) to monitor the dissolution kinetics of local low to medium grade rock phosphate sources and their effect on soil properties and (d) to evaluate their agronomic effectiveness in greenhouse and field experiments. Since most of the studied soils had very low concentrations of soluble P and high P-fixing capacities, the isotopic kinetic method was found unsuitable for evaluating soil P fertility and to predict plant P uptake. In contrast, the proposed chemical extraction method (NaHCO 3 -NH 4 F) predicted very well plant P uptake, suggesting that this extraction method can be routinely used to evaluate soil bioavailable P in similar soils in subtropical China. From the incubation study, it was found that although the local low to medium grade RPs were inferior to the

Thermal Inertia of Rocks and Rock Populations

Science.gov (United States)

Golombek, M. P.; Jakosky, B. M.; Mellon, M. T.

2001-01-01

The effective thermal inertia of rock populations on Mars and Earth is derived from a model of effective inertia versus rock diameter. Results allow a parameterization of the effective rock inertia versus rock abundance and bulk and fine component inertia. Additional information is contained in the original extended abstract.

Maturity group classification and maturity locus genotyping of early-maturing soybean varieties from high-latitude cold regions.

Science.gov (United States)

Jia, Hongchang; Jiang, Bingjun; Wu, Cunxiang; Lu, Wencheng; Hou, Wensheng; Sun, Shi; Yan, Hongrui; Han, Tianfu

2014-01-01

With the migration of human beings, advances of agricultural sciences, evolution of planting patterns and global warming, soybeans have expanded to both tropical and high-latitude cold regions (HCRs). Unlike other regions, HCRs have much more significant and diverse photoperiods and temperature conditions over seasons or across latitudes, and HCR soybeans released there show rich diversity in maturity traits. However, HCR soybeans have not been as well classified into maturity groups (MGs) as other places. Therefore, it is necessary to identify MGs in HCRs and to genotype the maturity loci. Local varieties were collected from the northern part of Northeast China and the far-eastern region of Russia. Maturity group reference (MGR) soybeans of MGs MG000, MG00, and MG0 were used as references during field experiments. Both local varieties and MGR soybeans were planted for two years (2010-2011) in Heihe (N 50°15', E 127°27', H 168.5 m), China. The days to VE (emergence), R1 (beginning bloom) and R7 (beginning maturity) were recorded and statistically analyzed. Furthermore, some varieties were further genotyped at four molecularly-identified maturity loci E1, E2, E3 and E4. The HCR varieties were classified into MG0 or even more early-maturing. In Heihe, some varieties matured much earlier than MG000, which is the most early-maturing known MG, and clustered into a separate group. We designated the group as MG0000, following the convention of MGs. HCR soybeans had relatively stable days to beginning bloom from emergence. The HCR varieties diversified into genotypes of E1, E2, E3 and E4. These loci had different effects on maturity. HCRs diversify early-maturing MGs of soybean. MG0000, a new MG that matures much earlier than known MGs, was developed. HCR soybean breeding should focus more on shortening post-flowering reproductive growth. E1, E2, E3, and E4 function differentially.

Studying physical properties of deformed intact and fractured rocks by micro-scale hydro-mechanical-seismicity model

Science.gov (United States)

Raziperchikolaee, Samin

The pore pressure variation in an underground formation during hydraulic stimulation of low permeability formations or CO2 sequestration into saline aquifers can induce microseismicity due to fracture generation or pre-existing fracture activation. While the analysis of microseismic data mainly focuses on mapping the location of fractures, the seismic waves generated by the microseismic events also contain information for understanding of fracture mechanisms based on microseismic source analysis. We developed a micro-scale geomechanics, fluid-flow and seismic model that can predict transport and seismic source behavior during rock failure. This model features the incorporation of microseismic source analysis in fractured and intact rock transport properties during possible rock damage and failure. The modeling method considers comprehensive grains and cements interaction through a bonded-particle-model. As a result of grain deformation and microcrack development in the rock sample, forces and displacements in the grains involved in the bond breakage are measured to determine seismic moment tensor. In addition, geometric description of the complex pore structure is regenerated to predict fluid flow behavior of fractured samples. Numerical experiments are conducted for different intact and fractured digital rock samples, representing various mechanical behaviors of rocks and fracture surface properties, to consider their roles on seismic and transport properties of rocks during deformation. Studying rock deformation in detail provides an opportunity to understand the relationship between source mechanism of microseismic events and transport properties of damaged rocks to have a better characterizing of fluid flow behavior in subsurface formations.

Lidar-Based Rock-Fall Hazard Characterization of Cliffs

Science.gov (United States)

Collins, Brian D.; Greg M.Stock,

2017-01-01

Rock falls from cliffs and other steep slopes present numerous challenges for detailed geological characterization. In steep terrain, rock-fall source areas are both dangerous and difficult to access, severely limiting the ability to make detailed structural and volumetric measurements necessary for hazard assessment. Airborne and terrestrial lidar survey methods can provide high-resolution data needed for volumetric, structural, and deformation analyses of rock falls, potentially making these analyses straightforward and routine. However, specific methods to collect, process, and analyze lidar data of steep cliffs are needed to maximize analytical accuracy and efficiency. This paper presents observations showing how lidar data sets should be collected, filtered, registered, and georeferenced to tailor their use in rock fall characterization. Additional observations concerning surface model construction, volumetric calculations, and deformation analysis are also provided.

The Eocene Rusayl Formation, Oman, carbonaceous rocks in calcareous shelf sediments: Environment of deposition, alteration and hydrocarbon potential

Energy Technology Data Exchange (ETDEWEB)

Dill, H.G.; Wehner, H.; Kus, J. [Federal Institute for Geosciences and Natural Resources, P.O. Box 510163, D-30631 Hannover (Germany); Botz, R. [University Kiel, Geological-Paleontological Department, Olshausenstrasse 40-60, D-24118 Kiel (Germany); Berner, Z.; Stueben, D. [Technical University Karlsruhe, Institute for Mineralogy and Geochemistry, Fritz-Haber-Weg 2, D-76131 Karlsruhe (Germany); Al-Sayigh, A. [Sultan Qaboos University, Geological Dept. PO Box 36, Al-Khod (Oman)

2007-10-01

Paralic carbonaceous series intercalated among calcareous shelf sediments have seldom been investigated. During the early Eocene, calcareous and siliciclastic sediments were deposited on a wide shelf in front of low-reliefed hinterland in the Al Khawd region in NE Oman. The siliciclastic-calcareous sediments originated from strongly reworked debris of the Arabic Shield. The underlying Semail Ophiolite did not act as a direct source of debris but provided some heat to increase the maturity of carbonaceous rocks and modify the isotope signal of the calcareous minerals in the Rusayl Formation. A multidisciplinary approach involving sedimentology, mineralogy, chemistry, coal petrography and paleontology resulted in the establishment of nine stratigraphic lithofacies units and provides the reader with a full picture from deposition of the mixed carbonaceous-calcareous-siliciclastic rocks to the most recent stages of post-depositional alteration of the Paleogene formations. The calcareous Jafnayn Formation (lithofacies unit I) developed in a subtidal to intertidal regime, influenced episodically by storms. Deepening of the calcareous shelf towards younger series was ground to a halt by paleosols developing on a disconformity (lithofacies unit II) and heralding the onset of the Rusayl Formation. The stratigraphic lithofacies units III and IV reflect mangrove swamps which from time to time were flooded through washover fans from the open sea. The presence of Spinozonocolpites and the taxon Avicennia, which today belong to a coastal marsh vegetational community, furnish palynological evidence to the idea of extensive mangrove swamps in the Rusayl Formation [El Beialy, S.Y., 1998. Stratigraphic and palaeonenvironmental significance of Eocene palynomorphs from the Rusayl Shale Formation, Al Khawd, northern Oman. Review of Palaeobotany and Palynology 102, 249-258]. During the upper Rusayl Formation (lithofacies units V through VII) algal mats episodically flooded by marine

Rock-fall Hazard In The Yosemite Valley, California

Science.gov (United States)

Guzzetti, F.; Reichenbach, P.; Wieczorek, G. F.

Rock slides and rock falls are the most frequent slope movements in Yosemite Na- tional Park, California. In historical time (1851-2001), more than 400 rock falls and rock slides have been documented in the valley, and some of them have been mapped in detail. We present the preliminary results of an attempt to assess rockfall hazard in the Yosemite Valley using STONE, a 3-dimensional rock-fall simulation computer program. The software computes 3-dimensional rock-fall trajectories starting from a digital terrain model (DTM), the location of rock-fall release points (source areas), and maps of the dynamic rolling coefficient and of the coefficients of normal and tan- gential energy restitution. For each DTM cell the software also calculates the number of rock falls passing through the cell, the maximum rock-fall velocity and the maxi- mum flying height. For the Yosemite Valley, a DTM with a ground resolution of 10 x 10 m was prepared using topographic contour lines from USGS 1:24,000-scale maps. Rock-fall release points were identified as DTM cells having a slope steeper than 60 degrees, an assumption based on the location of historical rock falls. Maps of the nor- mal and tangential energy restitution coefficients and of the rolling friction coefficient were produced from a surficial geologic map. The availability of historical rock falls mapped in detail allowed us to check the computer program performance and to cali- brate the model parameters. Visual and statistical comparison of the model results with the mapped rock falls confirmed the accuracy of the model. The model results are also compared with a geomorphic assessment of rock-fall hazard based on potential energy referred to as a "shadow angle" approach, recently completed for the Yosemite Valley.

Metamorphic Rock-Hosted Orogenic Gold Deposit Type as a Source of Langkowala Placer Gold, Bombana, Southeast Sulawesi

Directory of Open Access Journals (Sweden)

Arifudin Idrus

2014-06-01

Full Text Available DOI: 10.17014/ijog.v6i1.114In 2008, placer gold was discovered in Langkowala area (Bombana Regency, Southeast Sulawesi, Indonesia, and more than 60,000 traditional gold miners in the early 2009 have been operating by digging vertical pits and panning active stream sediments. The grade of placer gold ranges from 50 to 140 g/t. Local geological framework indicates that the placer gold is not related to volcanic rock-related hydrothermal gold deposit, e.g. epithermal, skarn or porphyry. This paper describes a preliminary study on possible primary deposit type as a source of the Langkowala (Bombana secondary placer gold. A field study indicates that the Langkowala (Bombana placer/paleoplacer gold is possibly related to gold-bearing quartz veins/veinlets hosted by metamorphic rocks particularly mica schist and metasediments in the area. These quartz veins/veinlets are currently recognized in metamorphic rocks at Wumbubangka Mountains, a northern flank of Rumbia Mountain Range. Sheared, segmented quartz veins/veinlets are of 2 cm to 2 m in width and contain gold in a grade varying between 2 and 61 g/t. At least, there are two generations of the quartz veins. The first generation of quartz vein is parallel to foliation of mica schist and metasediments with general orientation of N 300oE/60o; the second quartz vein generation crosscut the first quartz vein and the foliation of the wallrock. The first quartz veins are mostly sheared/deformed, brecciated, and occasionally sigmoidal, whereas the second quartz veins are relatively massive. The similar quartz veins/veinlets types are also probably present in Mendoke Mountain Range, in the northern side of Langkowala area. This primary gold deposit is called as ‘orogenic gold type’. The orogenic gold deposit could be a new target of gold exploration in Indonesia in the future.

Rock-brine chemical interactions. Final report

Energy Technology Data Exchange (ETDEWEB)

1982-02-01

The results of experimental interaction of powdered volcanic rock with aqueous solutions are presented at temperatures from 200 to 400/sup 0/C, 500 to 1000 bars fluid pressure, with reaction durations of approximately 30 days under controlled laboratory conditions. The aim of this research is to develop data on the kinetics and equilibria of rock solution interactions that will provide insight into the complex geochemical processes attending geothermal reservoir development, stimulation, and reinjection. The research was done in the Stanford Hydrothermal Lab using gold cell equipment of the Dickson design. This equipment inverts the solution rock mixture several times a minute to ensure thorough mixing. Solution samples were periodically withdrawn without interruption of the experimental conditions. The data from these experiments suggests a path dependent series of reactions by which geothermal fluids might evolve from meteoric or magmatic sources.

Acoustic emission measurements in petroleum-related rock mechanics

Energy Technology Data Exchange (ETDEWEB)

Unander, Tor Erling

2002-07-01

Acoustic emission activity in rock has usually been studied in crystalline rock, which reflects that rock mechanics has also mostly been occupied with such rocks in relations to seismology, mining and tunneling. On the other hand, petroleum-related rock mechanics focuses on the behaviour of sedimentary rock. Thus, this thesis presents a general study of acoustic emission activity in sedimentary rock, primarily in sandstone. Chalk, limestone and shale have also been tested, but to much less degree because the AE activity in these materials is low. To simplify the study, pore fluids have not been used. The advent of the personal computer and computerized measuring equipment have made possible new methods both for measuring and analysing acoustic emissions. Consequently, a majority of this work is devoted to the development and implementation of new analysis techniques. A broad range of topics are treated: (1) Quantification of the AE activity level, assuming that the event rate best represents the activity. An algorithm for estimating the event rate and a methodology for objectively describing special changes in the activity e.g., onset determination, are presented. (2) Analysis of AE waveform data. A new method for determining the source energy of an AE event is presented, and it is shown how seismic source theory can be used to analyze even intermediate quality data. Based on these techniques, it is shown that a major part of the measured AE activity originates from a region close to the sensor, not necessarily representing the entire sample. (3) An improved procedure for estimating source locations is presented. The main benefit is a procedure that better handles arrival time data with large errors. Statistical simulations are used to quantify the uncertainties in the locations. The analysis techniques are developed with the application to sedimentary rock in mind, and in two articles, the techniques are used in the study of such materials. The work in the first

) Organic Facies Variations in the Middle Cretaceous Black Shales of the Abakaliki Fold Belt, South-East, Nigeria

International Nuclear Information System (INIS)

Ehinola, O. A.; Badejoko, T.A.; Ekweozor, C.M.; Adebowale, K. O.

2003-01-01

An assessment, based on organic facies characteristics, have been carried out on the middle Cretaceous black shales, in order to determine their hydrocarbon source potential, thermal maturity, and depositional environments. The methods employed include evaluation of organic carbon content, rockeval pyrolysis, extractable organic matter, maceral composition and biomarker distributions.Organic facies criteria such as TOC, HI, Tmax, liptinite content, SOMIFOC and SHC/AHC indicate that Albian to middle Cenomanian shales are could only generate gas. The late Cenomanian to early Turonian shales are characterized by Type I/II kerogen, mature and could generate both oil and characterized by Type III kerogen, immature and could generate gas with little oil. The biomarker distributions indicate immature to mature source rock, moderately biodegraded and with reduced marine environment prevailing during the deposition of the lack shales. The late Cenomanian to early Turonian black shales show the highest source-rock potential

Rock pushing and sampling under rocks on Mars

Science.gov (United States)

Moore, H.J.; Liebes, S.; Crouch, D.S.; Clark, L.V.

1978-01-01

Viking Lander 2 acquired samples on Mars from beneath two rocks, where living organisms and organic molecules would be protected from ultraviolet radiation. Selection of rocks to be moved was based on scientific and engineering considerations, including rock size, rock shape, burial depth, and location in a sample field. Rock locations and topography were established using the computerized interactive video-stereophotogrammetric system and plotted on vertical profiles and in plan view. Sampler commands were developed and tested on Earth using a full-size lander and surface mock-up. The use of power by the sampler motor correlates with rock movements, which were by plowing, skidding, and rolling. Provenance of the samples was determined by measurements and interpretation of pictures and positions of the sampler arm. Analytical results demonstrate that the samples were, in fact, from beneath the rocks. Results from the Gas Chromatograph-Mass Spectrometer of the Molecular Analysis experiment and the Gas Exchange instrument of the Biology experiment indicate that more adsorbed(?) water occurs in samples under rocks than in samples exposed to the sun. This is consistent with terrestrial arid environments, where more moisture occurs in near-surface soil un- der rocks than in surrounding soil because the net heat flow is toward the soil beneath the rock and the rock cap inhibits evaporation. Inorganic analyses show that samples of soil from under the rocks have significantly less iron than soil exposed to the sun. The scientific significance of analyses of samples under the rocks is only partly evaluated, but some facts are clear. Detectable quantities of martian organic molecules were not found in the sample from under a rock by the Molecular Analysis experiment. The Biology experiments did not find definitive evidence for Earth-like living organisms in their sample. Significant amounts of adsorbed water may be present in the martian regolith. The response of the soil

Excess europium content in Precambrian sedimentary rocks and continental evolution

Science.gov (United States)

Jakes, P.; Taylor, S. R.

1974-01-01

It is proposed that the europium excess in Precambrian sedimentary rocks, relative to those of younger age, is derived from volcanic rocks of ancient island arcs, which were the source materials for the sediments. Precambrian sedimentary rocks and present-day volcanic rocks of island arcs have similar REE patterns, total REE abundances, and excess Eu, relative to the North American shale composite. The present upper crustal REE pattern, as exemplified by that of sediments, is depleted in Eu, relative to chondrites. This depletion is considered to be a consequence of development of a granodioritic upper crust by partial melting in the lower crust, which selectively retains europium.

Uranium occurrence in major rock types by fission-track mapping

International Nuclear Information System (INIS)

Ledger, E.G.; Bomber, B.J.; Schaftenaar, W.E.; Tieh, T.T.

1984-01-01

Microscopic occurrence of uranium has been determined in about 50 igneous rocks from various location, and in a genetically unrelated sandstone from south Texas. Precambrian granites from the Llano uplift of central Texas contain from a few ppm uranium (considered normal) to over 100 ppm on a whole-rock basis. In granite, uranium is concentrated in: (1) accessory minerals including zircon, biotite, allanite, Fe-Ti oxides, and altered sphene, (2) along grain boundaries and in microfractures by precipitation from deuteric fluids, and (3) as point sources (small inclusions) in quartz and feldspars. Tertiary volcanic rocks from the Davis Mountains of west Texas include diverse rock types from basalt to rhyolite. Average uranium contents increase from 1 ppm in basalts to 7 ppm in rhyolites. Concentration occurs: (1) in iron-titanium-oxides, zircon, and rutile, (2) in the fine-grained groundmass as uniform and point-source concentrations, and (3) as late uranium in cavities associated with banded, silica-rich material. Uranium in ore-grade sandstone is concentrated to more than 3%. Specific occurrences include (1) leucoxene and/or anatase, (2) opaline and calcite cements, (3) mud clasts and altered volcanic rock fragments, and (4) in a few samples, as silt-size uranium- and molybdenum-rich spheres. Uranium content is quite low in pyrite, marcasite, and zeolites

Low-maturity Kulthieth Formation coal : a possible source of polycyclic aromatic hydrocarbons in benthic sediment of the Northern Gulf of Alaska

International Nuclear Information System (INIS)

Van Kooten, G.K.; Short, J.W.; Kolak, J.J.

2002-01-01

This study addressed the issue of sources of hydrocarbons for benthic sediments in the Gulf of Alaska (GOA) with particular reference to the application of forensic geology to identify end members and to explain the geologic setting and processes affecting the system. Native coals and natural seep oils have been questioned in the past decade as possible sources of background hydrocarbons because the pattern of relative polycyclic aromatic hydrocarbon (PAH) abundance characteristic of benthic GOA sediments is inconsistent with patterns typical of weathered seep oils. Native coal has also been dismissed as a pollution source because ratios of labile hydrocarbons to total organic carbon for Bering River coal field (BRCF) sources are too low to be consistent with GOA sediments. The authors present evidence that perhaps native coal has been prematurely dismissed as a pollution source because BRCF coals do not represent adequately the geochemical signatures of coals elsewhere in the Kulthieth Formation which have much higher PAH:TOC ratios. The patterns of labile hydrocarbons in these low thermal maturity coals indicate a genetic relationship between Kulthieth Formation coals and nearby oil seeps on the Sullivan anticline. Analysis of the coal suggests it is a significant source of PAH, and it was cautioned that source models that do not include this source will underestimate the contribution of native coals to the background hydrocarbon signature in the Gulf of Alaska. 32 refs., 2 tabs., 8 figs

Strontium isotopic geochemistry of intrusive rocks, Puerto Rico, Greater Antilles

International Nuclear Information System (INIS)

Jones, L.M.; Kesler, S.E.

1980-01-01

The strontium isotope geochemistry is given for three Puerto Rican intrusive rocks: the granodioritic Morovis and San Lorenzo plutons and the Rio Blanco stock of quartz dioritic composition. The average calculated initial 87 Sr/ 86 Sr ratios are 0.70370, 0.70355 and 0.70408, respectively. In addition, the San Lorenzo data establish a whole-rock isochron of 71 +- 2 m.y., which agrees with the previously reported K-Ar age of 73 m.y. Similarity of most of the intrusive rocks in the Greater Antilles with respect to their strontium isotopic geochemistry regardless of their major element composition indicates that intrusive magmas with a wide range of composition can be derived from a single source material. The most likely source material, in view of the available isotopic data, is the mantle wedge overlying the subduction zone. (orig.)

Resource Assessment of the In-Place and Potentially Recoverable Deep Natural Gas Resource of the Onshore Interior Salt Basins, North Central and Northeastern Gulf of Mexico

Energy Technology Data Exchange (ETDEWEB)

Ernest A. Mancini; Donald A. Goddard

2005-04-15

The principal research effort for the first six months of Year 2 of the project has been petroleum system characterization. Understanding the burial and thermal maturation histories of the strata in the onshore interior salt basins of the North Central and Northeastern Gulf of Mexico areas is important in petroleum system characterization. The underburden and overburden rocks in these basins and subbasins are a product of their rift-related geohistory. Petroleum source rock analysis and thermal maturation and hydrocarbon expulsion modeling indicate that an effective regional petroleum source rock in the onshore interior salt basins, the North Louisiana Salt Basin, Mississippi Interior Salt Basin, Manila Subbasin and Conecuh Subbasin, was the Upper Jurassic Smackover lime mudstone. The Upper Cretaceous Tuscaloosa shale was an effective local petroleum source rock in the Mississippi Interior Salt Basin and a possible local source bed in the North Louisiana Salt Basin. Hydrocarbon generation and expulsion was initiated in the Early Cretaceous and continued into the Tertiary in the North Louisiana Salt Basin and the Mississippi Interior Salt Basin. Hydrocarbon generation and expulsion was initiated in the Late Cretaceous and continued into the Tertiary in the Manila Subbasin and Conecuh Subbasin. Reservoir rocks include Jurassic, Cretaceous and Tertiary siliciclastic and carbonate strata. Seal rocks include Jurassic, Cretaceous and Tertiary anhydrite and shale beds. Petroleum traps include structural and combination traps.

Petroleum generation 3D modeling of Espirito Santo Basin, Brazil; Modelagem 3D da geracao de petroleo na Bacia do Espirito Santo, Brasil

Energy Technology Data Exchange (ETDEWEB)

Ferreira, Daniella A.; Lemgruber, Adriana; Goncalves, Felix T.T. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE). Lab. de Modelagem Multidisciplinar de Bacias Sedimentares (LAB2M); Petersohn, Eliane [Agencia Nacional do Petroleo, Gas Natural e Biocombustiveis (ANP), Rio de Janeiro, RJ (Brazil)

2008-07-01

Intervals of potential source rocks were identified and characterized by the analysis and interpretation of total organic carbon (TOC) and Rock-Eval pyrolysis data. The rift section presents the best conditions for hydrocarbon generation, especially in Mariricu formation, that presents high TOC, hydrogen index and type I Kerogen. The drift section possesses low source rock potential, the intervals with best organic matter characteristic (quantity and quality) are represented by thin packages positioned in the superior portion of Regencia and Sao Mateus formation and in the basis of Urucutuca formation. The geochemistry data was integrated, on a regional scale, into the thermal maturation and petroleum generation three-dimensional model. Four potentially source rock intervals were simulated, two in the pre-salt section and two in the post-salt section. The results point out that the pre-salt intervals have reached thermal maturity in the proximal shelf and were overmatured in deep water. The thermal evolution obtained for the post-salt zone was very similar to those obtained for the rift section (pre-salt section). (author)

Petroleum migration and mixing in the Pearl River Mouth Basin, South China Sea

Energy Technology Data Exchange (ETDEWEB)

Chunming Zhang [Jianghan Petroleum Univ., Geochemistry Research Center, Jingzhou, Hubei (China); China Univ. of Geosciences, Dept. of Energy Resources, Beijing (China); Sitian Li [China Univ. of Geosciences, Dept. of Energy Resources, Beijing (China); Jiaming Yang [China National Offshore Oil Corp., Beijing (China); Shaokun Yang; Jianrong Wang [Nanhai East Oil Co., Research Inst., Guangzhou (China)

2004-02-01

Two oil groups have been investigated in the Pearl River Mouth Basin using their geochemical characteristics. In combination with source data, the two oil groups may be extrapolated into two end-member oils: petroleum populations A and B. The oil population A with abundant 4-methylsteranes, derived from the deeper Wenchang source rocks, migrated and accumulated earlier. The oil population B with absent 4-methylsteranes was expelled from the Enping source rocks and is associated with a relatively later phase of migration and accumulation. The two distinctive oil populations migrated updip through the marine blanket-like sandstone carriers within the Zhuhai Formation to accumulate in a series of traps along the main migration pathways at different times. Most of the accumulations are mixtures of the two end-member oils. The variations of 4-methylsterane concentrations in the accumulations can be related to the contributions from the two sources: the oils, which migrated furthest, contain greater contributions from the Wenchang source rocks, whereas those with shorter migration paths have greater contributions from the Enping sources. The later migrated oils closer to the depression areas are highly mature and the former oils in the Liuhua oil fields are of relatively low maturity, which may indicate the main migration direction along the Hui-Liu Structure Ridge (HLSR). Oils with abnormally high maturity in the middle of the HLSR may suggest oil-filling points, from which branch conduits connected the source kitchens to the main migration pathway. Oils with abnormally low maturities may reveal minor contributions from some small sags in the Dongsha Massif in a later phase. (Author)

Favorability for uranium in tertiary sedimentary rocks, southwestern Montana

International Nuclear Information System (INIS)

Wopat, M.A.; Curry, W.E.; Robins, J.W.; Marjaniemi, D.K.

1977-10-01

Tertiary sedimentary rocks in the basins of southwestern Montana were studied to determine their favorability for potential uranium resources. Uranium in the Tertiary sedimentary rocks was probably derived from the Boulder batholith and from silicic volcanic material. The batholith contains numerous uranium occurrences and is the most favorable plutonic source for uranium in the study area. Subjective favorability categories of good, moderate, and poor, based on the number and type of favorable criteria present, were used to classify the rock sequences studied. Rocks judged to have good favorability for uranium deposits are (1) Eocene and Oligocene strata and undifferentiated Tertiary rocks in the western Three Forks basin and (2) Oligocene rocks in the Helena basin. Rocks having moderate favorability consist of (1) Eocene and Oligocene strata in the Jefferson River, Beaverhead River, and lower Ruby River basins, (2) Oligocene rocks in the Townsend and Clarkston basins, (3) Miocene and Pliocene rocks in the Upper Ruby River basin, and (4) all Tertiary sedimentary formations in the eastern Three Forks basin, and in the Grasshopper Creek, Horse Prairie, Medicine Lodge Creek, Big Sheep Creek, Deer Lodge, Big Hole River, and Bull Creek basins. The following have poor favorability: (1) the Beaverhead Conglomerate in the Red Rock and Centennial basins, (2) Eocene and Oligocene rocks in the Upper Ruby River basin, (3) Miocene and Pliocene rocks in the Townsend, Clarkston, Smith River, and Divide Creek basins, (4) Miocene through Pleistocene rocks in the Jefferson River, Beaverhead River, and Lower Ruby River basins, and (5) all Tertiary sedimentary rocks in the Boulder River, Sage Creek, Muddy Creek, Madison River, Flint Creek, Gold Creek, and Bitterroot basins

Detrital Zircons From the Jack Hills and Mount Narryer, Western Australia: Geochronological, Morphological, and Geochemical Evidence for Diverse >4000 Ma Source Rocks

Science.gov (United States)

Crowley, J. L.; Myers, J. S.; Sylvester, P. J.; Cox, R. A.

2004-05-01

Detrital zircons from all major clastic units in the Jack Hills and Mount Narryer metasedimentary belts, Western Australia, were analyzed for morphology, internal zoning, inclusion mineralogy, age, and trace element concentrations (latter two obtained by laser-ablation microprobe ICPMS). The results show that zircons were derived from a wide diversity of rocks, including previously described, >4000 Ma grains that are older than any known terrestrial rocks. In three metaconglomerate samples from the western Jack Hills, 4200-3800 Ma zircons ("old grains") comprise 14% of the population, 3800-3600 Ma grains form only 2%, and 3550-3250 Ma zircons ("young grains") are dominant with a significant peak at 3380 Ma. Old and young grains are interpreted as being from similar rock types because they are indistinguishable in trace element concentrations, size (several hundred microns), morphology (subequant, typically fragmented), internal zoning (typically both oscillatory and sector), and U concentration (50-200 ppm). Many of these properties suggest an intermediate plutonic source, whereas an evolved granitic source was previously interpreted from rare-earth element and oxygen isotope data. Detrital zircons in quartzites and metaconglomerates at Mount Narryer differ significantly from zircons from the western Jack Hills. Old grains comprise only 3% (most of which are 4200-4100 Ma), 3800-3600 Ma zircons form 31%, and there are peaks at 3650, 3600, and 3500 Ma. Old and young grains have similar properties that suggest granitic sources, such as elongate prismatic morphology, oscillatory zoning, high U concentrations (100-600 ppm), and xenotime and monazite inclusions. Trace element concentrations are broadly similar to those in Jack Hills zircons, with notable exceptions being generally higher U, smaller Ce and Eu anomalies, and lower Nb/Ta. It is considered unlikely that Jack Hills zircons were derived from granitic gneisses that surround the metasedimentary belts because

Field studies on two rock phosphate solubilizing actinomycete isolates as biofertilizer sources

Science.gov (United States)

Mba, Caroline C.

1994-03-01

Recently biotechnology is focusing attention on utilization of biological resources to solve a number of environmental problems such as soil fertility management. Results of microbial studies on earthworm compost in the University of Nigeria farm identified a number of rock phosphate solubilizing actinomycetes. Two of these, isclates 02 and 13, were found to be efficient rock phosphate (RP) solubilizers and fast-growing cellulolytic microbes producing extracellular hydrolase enzymes. In this preliminary field study the two microbial isolates were investigated with respect to their effects on the growth of soybean and egusi as well as their effect on the incidence of toxicity of poultry droppings. Application of these isolates in poultry manure-treated field plots, as microbial fertilizers, brought about yield increases of 43% and 17% with soybeans and 19% and 33% with egusi, respectively. Soil properties were also improved. With isolates 02 and 13, the soil available phosphorus increased at the five-leaf stage, while N-fixation in the soil increased by 45% or 11% relative to control. It was further observed that air-dried poultry manure after four days of incubation was still toxic to soybean. The toxic effect of the applied poultry manure was reduced or eliminated with microbial fertilizers 02 or 13, respectively. The beneficial effects of the microbial organic fertilizer are discussed. Justification for more intensive research on rock phosphate organic fertilizer is highlighted.

EVALUATION OF THE BIOSOLIDS COMPOST MATURITY IN SOUTH ISFAHAN WASTEWATER TREATMENT PLANT

Directory of Open Access Journals (Sweden)

H. Alidadi, A. R. Parvaresh, M. R. Shahmansouri, H. Pourmoghadas

2008-04-01

Full Text Available The composting process is a useful method of producing a stabilized material that can be used as a source of nutrients and soil conditioner. Maturity of compost is essential for its optimal use as a soil amendment and a source of plant nutrients as well. Immature composts pose problems of malodors and flies and phytotoxicity and pollution during use. Stability and maturity both are required for compost quality control. Compost maturity tests can be classified into physical, chemical, plant, and microbial activity assays. In this study, several methods of evaluating the stability and maturity of composted biosolids were compared based on chemical and biological properties. The sludge used of windrow composting was obtained from the drying beds of South Isfahan wastewater treatment plant. The results showed that, C/N ratio after 100 days of composting reached to 15/1; NH4/NO3 ratio decreased with increase of the time dewatered sludge compost, which this loss is 57.3%. The content of volatile solids, 28.8% decreased with composting time. The number of fecal coliforms in the initial sewage sludge compost was 17.9´106 and at the end of composting was 898MPN/g of total solids and the compost process provided class A pathogen criteria. Use of chemical and biological parameters exhibited three phases: rapid decomposition (day 40, stabilization (day 80 and maturation (day 100 in biosolids compost. Thus, the biosolid compost was mature and ready for use as an agricultural substrate after about 100 days of composting.

Development of soda-lime glasses from ornamental rock wastes

International Nuclear Information System (INIS)

Babisk, Michelle Pereira

2009-01-01

During the ornamental rocks production, among other steps, one saw the rock blocks in order to transform them into semi-finished plates. In this step, expressive amounts of residues are generated, which are not properly discharged in nature, without any programmed utilization. The residues of silicide rocks present, in their compositions, oxides which are raw materials employed to fabricate soda-lime type glasses (containing SiO_2, Al_2O_3, CaO, Na_2O and K_2O). On the other hand the residues of carbonatic rocks are constituted of glass net modifier oxides, like CaO and MgO. In this work it was developed four types of soda-lime glasses using ornamental rock residues, where the glasses compositions were adjusted by adding sand, as silica source, as well as sodium and calcium carbonates as sources of Na_2O and CaO, respectively. The obtained glasses were characterized by means of Archimed's method for densities measurements, microstructure by using optical and electronic microscopy, phases by means of X-ray diffraction (XRD), hardness by Vickers indentation, spectroscopy (UV/VIS), and hydrolytic resistance according to ISO 719. The XRD analyses confirmed the compositions total vitrification, where the greened aspect of the samples was due to the presence of the iron oxides. The produced glasses properties were compared with those of commercial glasses aiming their industrial employment. The main difference between the produced glasses and those commercials varied primarily regarding the amount of carbonates incorporated. The results showed that the ornamental rocks residues may be used as raw materials for glasses fabrication, and they found a useful economic destination rather than discharge which promotes undesirable environmental impact. (author)

Estimating the Wet-Rock P-Wave Velocity from the Dry-Rock P-Wave Velocity for Pyroclastic Rocks

Science.gov (United States)

Kahraman, Sair; Fener, Mustafa; Kilic, Cumhur Ozcan

2017-07-01

Seismic methods are widely used for the geotechnical investigations in volcanic areas or for the determination of the engineering properties of pyroclastic rocks in laboratory. Therefore, developing a relation between the wet- and dry-rock P-wave velocities will be helpful for engineers when evaluating the formation characteristics of pyroclastic rocks. To investigate the predictability of the wet-rock P-wave velocity from the dry-rock P-wave velocity for pyroclastic rocks P-wave velocity measurements were conducted on 27 different pyroclastic rocks. In addition, dry-rock S-wave velocity measurements were conducted. The test results were modeled using Gassmann's and Wood's theories and it was seen that estimates for saturated P-wave velocity from the theories fit well measured data. For samples having values of less and greater than 20%, practical equations were derived for reliably estimating wet-rock P-wave velocity as function of dry-rock P-wave velocity.

Effects of structural heterogeneity on frictional heating from biomarker thermal maturity analysis of the Muddy Mountain thrust, Nevada, USA

Science.gov (United States)

Coffey, G. L.; Savage, H. M.; Polissar, P. J.; Rowe, C. D.

2017-12-01

Faults are generally heterogeneous along-strike, with changes in thickness and structural complexity that should influence coseismic slip. However, observational limitations (e.g. limited outcrop or borehole samples) can obscure this complexity. Here we investigate the heterogeneity of frictional heating determined from biomarker thermal maturity and microstructural observations along a well-exposed fault to understand whether coseismic stress and frictional heating are related to structural complexity. We focus on the Muddy Mountain thrust, Nevada, a Sevier-age structure that has continuous exposure of its fault core and considerable structural variability for up to 50 m, to explore the distribution of earthquake slip and temperature rise along strike. We present new biomarker thermal maturity results that capture the heating history of fault rocks. Biomarkers are organic molecules produced by living organisms and preserved in the rock record. During heating, their structure is altered systematically with increasing time and temperature. Preliminary results show significant variability in thermal maturity along-strike at the Muddy Mountain thrust, suggesting differences in coseismic temperature rise on the meter- scale. Temperatures upwards of 500°C were generated in the principal slip zone at some locations, while in others, no significant temperature rise occurred. These results demonstrate that stress or slip heterogeneity occurred along the Muddy Mountain thrust at the meter-scale and considerable along-strike complexity existed, highlighting the importance of careful interpretation of whole-fault behavior from observations at a single point on a fault.

Petrology of lunar rocks and implication to lunar evolution

Science.gov (United States)

Ridley, W. I.

1976-01-01

Recent advances in lunar petrology, based on studies of lunar rock samples available through the Apollo program, are reviewed. Samples of bedrock from both maria and terra have been collected where micrometeorite impact penetrated the regolith and brought bedrock to the surface, but no in situ cores have been taken. Lunar petrogenesis and lunar thermal history supported by studies of the rock sample are discussed and a tentative evolutionary scenario is constructed. Mare basalts, terra assemblages of breccias, soils, rocks, and regolith are subjected to elemental analysis, mineralogical analysis, trace content analysis, with studies of texture, ages and isotopic composition. Probable sources of mare basalts are indicated.

Effect of Thermal Maturation on n-alkanes and Kerogen in Preserved Organic Matter: Implications for Paleoenvironment Biomarkers

Science.gov (United States)

Craven, O. D.; Longbottom, T. L.; Hockaday, W. C.; Blackaby, E.

2017-12-01

Understanding the effects of maturity on biomarkers is vital in assessing biomarker reliability in mature sediments. It is well known for n-alkanes that increased maturity shortens chain lengths and decreases the odd over even preference however, the amount of change in these variables has not been determined for different maturities and types of preserved organic matter. For this reason, it is difficult to judge the trustworthiness of even lightly matured samples for paleoenvironment reconstruction. Another complication is the difficulty of accurately determining maturity as many maturity indicators are error-prone or not appropriate at low maturities. Using hydrous pyrolysis, we artificially matured black shale samples with type I (lacustrine) and type II (marine) kerogen to measure changes in n-alkane length and odd over even preference. Whole rock samples underwent hydrous pyrolysis for 72 hours, at 250 °C, 300 °C, 325 °C, 350 °C, and 375 °C to cover a wide maturity range. From the immature and artificially matured samples, the bitumen was extracted and the saturate fraction was separated using column chromatography. The saturate fraction was analyzed for n-alkanes using gas chromatography-mass spectroscopy. Kerogen structural changes were also measured using solid-state 13C NMR to relate changes in n-alkane biomarkers to changes in kerogen structure. Results show that for type I bitumen the n-alkanes did not change at low maturities considered premature in terms of oil generation (<325 °C). The NMR spectra of the type I kerogen support the lack of change, at low maturities no changes in the aliphatic portion (Fal) were observed, however, after 325 °C Fal decreased with increasing maturity. The loss of Fal indicates kerogen contributing hydrocarbons to bitumen that cause changes in n-alkane measurements. The type II kerogen's Fal also decreased with increasing maturity, but unlike the type I kerogen Fal loss started at low maturities. The differences

'Escher' Rock

Science.gov (United States)

2004-01-01

[figure removed for brevity, see original site] Chemical Changes in 'Endurance' Rocks [figure removed for brevity, see original site] Figure 1 This false-color image taken by NASA's Mars Exploration Rover Opportunity shows a rock dubbed 'Escher' on the southwestern slopes of 'Endurance Crater.' Scientists believe the rock's fractures, which divide the surface into polygons, may have been formed by one of several processes. They may have been caused by the impact that created Endurance Crater, or they might have arisen when water leftover from the rock's formation dried up. A third possibility is that much later, after the rock was formed, and after the crater was created, the rock became wet once again, then dried up and developed cracks. Opportunity has spent the last 14 sols investigating Escher, specifically the target dubbed 'Kirchner,' and other similar rocks with its scientific instruments. This image was taken on sol 208 (Aug. 24, 2004) by the rover's panoramic camera, using the 750-, 530- and 430-nanometer filters. The graph above shows that rocks located deeper into 'Endurance Crater' are chemically altered to a greater degree than rocks located higher up. This chemical alteration is believed to result from exposure to water. Specifically, the graph compares ratios of chemicals between the deep rock dubbed 'Escher,' and the more shallow rock called 'Virginia,' before (red and blue lines) and after (green line) the Mars Exploration Rover Opportunity drilled into the rocks. As the red and blue lines indicate, Escher's levels of chlorine relative to Virginia's went up, and sulfur down, before the rover dug a hole into the rocks. This implies that the surface of Escher has been chemically altered to a greater extent than the surface of Virginia. Scientists are still investigating the role water played in influencing this trend. These data were taken by the rover's alpha particle X-ray spectrometer.

Geochemical constraints on the petrogenesis of the pyroclastic rocks in Abakaliki basin (Lower Benue Rift), Southeastern Nigeria

Science.gov (United States)

Chukwu, Anthony; Obiora, Smart C.

2018-05-01

The pyroclastic rocks in the Cretaceous Abakaliki basin occur mostly as oval-shaped bodies, consisting of lithic/lava and vitric fragments. They are commonly characterized by parallel and cross laminations, as well contain xenoliths of shale, mudstone and siltstones from the older Asu River Group of Albian age. The rocks are basic to ultrabasic in composition, comprising altered alkali basalts, altered tuffs, minor lapillistones and agglomerates. The mineral compositions are characterized mainly by laths of calcic plagioclase, pyroxene (altered), altered olivines and opaques. Calcite, zeolite and quartz represent the secondary mineral constituents. Geochemically, two groups of volcaniclastic rocks, are distinguished: alkaline and tholeiitic rocks, both represented by fresh and altered rock samples. The older alkali basalts occur within the core of the Abakaliki anticlinorium while the younger tholeiites occur towards the periphery. Though most of the rocks are moderate to highly altered [Loss on ignition (LOI, 3.43-22.07 wt. %)], the use of immobile trace element such as Nb, Zr, Y, Hf, Ti, Ta and REEs reflect asthenospheric mantle source compositions. The rocks are enriched in incompatible elements and REEs (∑REE = 87.98-281.0 ppm for alkaline and 69.45-287.99 ppm for tholeiites). The ratios of La/Ybn are higher in the alkaline rocks ranging from 7.69 to 31.55 compared to the tholeiitic rocks which range from 4.4 to 16.89 and indicating the presence of garnet-bearing lherzolite in the source mantle. The spidergrams and REEs patterns along with Zr/Nb, Ba/Nb, Rb/Nb ratios suggest that the rocks were generated by a mantle plume from partial melting of mixed enriched mantle sources (HIMU, EMI and EMII) similar to the rocks of the south Atlantic Ocean such as St. Helena (alkaline rocks) and Ascension rocks (tholeiitic rocks). The rocks were formed in a within-plate setting of the intra-continental rift type similar to other igneous rocks in the Benue Rift and are not

Sr-Nd isotope systematics of xenoliths in Cenozoic volcanic rocks from SW Japan

International Nuclear Information System (INIS)

Kagami, Hiroo; Iwata, Masatoshi; Iizumi, Shigeru; Nureki, Terukazu.

1993-01-01

Based on new and previously published Sr and Nd isotope data, we examined the petrogenetic relationship between deep crust- and upper mantle-derived xenoliths contained in Cenozoic volcanic rocks and Cretaceous-Paleogene granitoid rocks in SW Japan. The deep crust- and upper mantle-derived mafic to ultramafic xenoliths contained in Cenozoic volcanic rocks from SW Japan have comparable initial Sr and Nd isotope ratios to the Cretaceous-Paleogene granitoid rocks in their respective districts. This may suggest that these xenoliths were genetically related to the Cretaceous-Paleogene granitoid rocks in SW Japan, and that regional variations in Sr and Nd isotope ratios observed in the granitoid rocks are attributed to differences in the geochemistry of the magma sources. (author)

The December 2008 Crammont rock avalanche, Mont Blanc massif area, Italy

Directory of Open Access Journals (Sweden)

P. Deline

2011-12-01

Full Text Available We describe a 0.5 Mm³ rock avalanche that occurred in 2008 in the western Alps and discuss possible roles of controlling factors in the context of current climate change. The source is located between 2410 m and 2653 m a.s.l. on Mont Crammont and is controlled by a densely fractured rock structure. The main part of the collapsed rock mass deposited at the foot of the rock wall. A smaller part travelled much farther, reaching horizontal and vertical travel distances of 3050 m and 1560 m, respectively. The mobility of the rock mass was enhanced by channelization and snow. The rock-avalanche volume was calculated by comparison of pre- and post-event DTMs, and geomechanical characterization of the detachment zone was extracted from LiDAR point cloud processing. Back analysis of the rock-avalanche runout suggests a two stage event.

There was no previous rock avalanche activity from the Mont Crammont ridge during the Holocene. The 2008 rock avalanche may have resulted from permafrost degradation in the steep rock wall, as suggested by seepage water in the scar after the collapse in spite of negative air temperatures, and modelling of rock temperatures that indicate warm permafrost (T > −2 °C.

Geological evolution, regional perspectives and hydrocarbon potential of the northwest Phu Khanh Basin, offshore Central Vietnam

DEFF Research Database (Denmark)

Fyhn, Michael Bryld Wessel; Nielsen, Lars H.; Boldreel, Lars Ole

2009-01-01

seeps are found at Dam Thi Nai, immediately landward of the basin. Geochemical analyses of the oil seeps indicate the existence of at least two early to peak mature source rocks. Maturation modelling, combined with the seismic analysis, suggests the likely presence of oil kitchens 40-50km downdip...

Maturity of nearby faults influences seismic hazard from hydraulic fracturing

Science.gov (United States)

Kozłowska, Maria; Brudzinski, Michael R.; Friberg, Paul; Skoumal, Robert J.; Baxter, Nicholas D.; Currie, Brian S.

2018-02-01

Understanding the causes of human-induced earthquakes is paramount to reducing societal risk. We investigated five cases of seismicity associated with hydraulic fracturing (HF) in Ohio since 2013 that, because of their isolation from other injection activities, provide an ideal setting for studying the relations between high-pressure injection and earthquakes. Our analysis revealed two distinct groups: (i) deeper earthquakes in the Precambrian basement, with larger magnitudes (M > 2), b-values 1.5, and few post–shut-in earthquakes. Based on geologic history, laboratory experiments, and fault modeling, we interpret the deep seismicity as slip on more mature faults in older crystalline rocks and the shallow seismicity as slip on immature faults in younger sedimentary rocks. This suggests that HF inducing deeper seismicity may pose higher seismic hazards. Wells inducing deeper seismicity produced more water than wells with shallow seismicity, indicating more extensive hydrologic connections outside the target formation, consistent with pore pressure diffusion influencing seismicity. However, for both groups, the 2 to 3 h between onset of HF and seismicity is too short for typical fluid pressure diffusion rates across distances of ˜1 km and argues for poroelastic stress transfer also having a primary influence on seismicity.

Maturity of nearby faults influences seismic hazard from hydraulic fracturing.

Science.gov (United States)

Kozłowska, Maria; Brudzinski, Michael R; Friberg, Paul; Skoumal, Robert J; Baxter, Nicholas D; Currie, Brian S

2018-02-20

Understanding the causes of human-induced earthquakes is paramount to reducing societal risk. We investigated five cases of seismicity associated with hydraulic fracturing (HF) in Ohio since 2013 that, because of their isolation from other injection activities, provide an ideal setting for studying the relations between high-pressure injection and earthquakes. Our analysis revealed two distinct groups: ( i ) deeper earthquakes in the Precambrian basement, with larger magnitudes (M > 2), b-values 1.5, and few post-shut-in earthquakes. Based on geologic history, laboratory experiments, and fault modeling, we interpret the deep seismicity as slip on more mature faults in older crystalline rocks and the shallow seismicity as slip on immature faults in younger sedimentary rocks. This suggests that HF inducing deeper seismicity may pose higher seismic hazards. Wells inducing deeper seismicity produced more water than wells with shallow seismicity, indicating more extensive hydrologic connections outside the target formation, consistent with pore pressure diffusion influencing seismicity. However, for both groups, the 2 to 3 h between onset of HF and seismicity is too short for typical fluid pressure diffusion rates across distances of ∼1 km and argues for poroelastic stress transfer also having a primary influence on seismicity.

Cenozoic alkaline volcanic rocks with carbonatite affinity in the Bohemian Massif: Their sources and magma generation

Czech Academy of Sciences Publication Activity Database

Ulrych, Jaromír; Štěpánková-Svobodová, Jana

2014-01-01

Roč. 46, 1/2 (2014), s. 45-58 ISSN 0369-2086 R&D Projects: GA AV ČR(CZ) IAA300130902 Institutional support: RVO:67985831 Keywords : alkaline volcanic rocks * melilitic rocks * carbonatites * magma generation * metasomatism * Cenozoic * Bohemian Massif Subject RIV: DB - Geology ; Mineralogy

Numerical Simulation of Blast Vibration and Crack Forming Effect of Rock-Anchored Beam Excavation in Deep Underground Caverns

Directory of Open Access Journals (Sweden)

XinPing Li

2017-01-01

Full Text Available Aiming at surrounding rock damage induced by dynamic disturbance from blasting excavation of rock-anchored beam in rock mass at moderate or far distance in underground cavern, numerical model of different linear charging density and crustal stress in underground cavern is established by adopting dynamic finite element software based on borehole layout, charging, and rock parameter of the actual situation of a certain hydropower station. Through comparison in vibration velocity, contour surface of rock mass excavation, and the crushing extent of excavated rock mass between calculation result and field monitoring, optimum linear charging density of blast hole is determined. Studies are also conducted on rock mass vibration in moderate or far distance to blasting source, the damage of surrounding rock in near-field to blasting source, and crushing degree of excavated rock mass under various in situ stress conditions. Results indicate that, within certain range of in situ stress, the blasting vibration is independent of in situ stress, while when in situ stress is increasing above certain value, the blasting vibration velocity will be increasing and the damage of surrounding rock and the crushing degree of excavated rock mass will be decreasing.

Petroleum geology framework, southeast Bowser Basin, British Columbia

Energy Technology Data Exchange (ETDEWEB)

Haggart, J.W. [Geological Survey of Canada, Vancouver, BC (Canada); Mahoney, J.B. [Wisconsin Univ., Eau Claire, WS (United States). Dept. of Geology

2003-07-01

There are significant coal resources in the northern regions of the Bowser basin in north-central British Columbia. However, the resource potential of the southern part of the basin has not been assessed, therefore the hydrocarbon potential is not known. Geological maps indicate several Mesozoic clastic and volcanic units across the southern part of the basin. Two stratigraphic intervals of the southern Bowser basin are considered to be potential source rocks within the Jurassic-Cretaceous strata. The fine-grained clastic rocks of the Bowser Lake Group contain significant amounts of carbonaceous material or organic matter. Well developed cleavage indicates that the rocks may be thermally over mature. This paper described potential reservoir rocks within the basin, along with their thermal maturation and conceptual play. 4 figs.

Rock fragmentation

Energy Technology Data Exchange (ETDEWEB)

Brown, W.S.; Green, S.J.; Hakala, W.W.; Hustrulid, W.A.; Maurer, W.C. (eds.)

1976-01-01

Experts in rock mechanics, mining, excavation, drilling, tunneling and use of underground space met to discuss the relative merits of a wide variety of rock fragmentation schemes. Information is presented on novel rock fracturing techniques; tunneling using electron beams, thermocorer, electric spark drills, water jets, and diamond drills; and rock fracturing research needs for mining and underground construction. (LCL)

Geophysical monitoring as an information source of rock massif behaviour

Directory of Open Access Journals (Sweden)

Pavel Bláha

2008-06-01

Full Text Available Geophysical measurements are an integral part of engineering-geological investigation where theypresent a wide range of useful information about the tested geological medium and about its geotechnicalqualities. Lately, repeated geophysical measurements in different time intervals have been used to judgethe changes occurring in the rock massif. These measurements bear the characteristics of total monitoring.This total monitoring contains series of repeated measurements and further an integrated spectrum of linkedactivities including evaluation, comparison with the warning state and making a decision about takingprecautions. From the range of geophysical methods and methodologies used for monitoring in full sensewe may mention, for example, continuous seismoacoustic measurements in mining constructions; (whichmay result even in recalling of the personnel, and further, also seismic measurements in the surroundingsof atomic power stations and measurements considering the protection against radioactive elements and their decay components.As a full monitoring we may also classify measurements in dumping sites with the aid of repeated geoelectrical measurements in the system of fixed electrodes under impermeable foils.These measurements are mostly carried out from time to time followed by taking immediate action when the foil is found damaged. In practice the term monitoring is used, although not very correctly, for all periodically repeated measurements, which do not result in taking action or interference, but supply a wide range of information about the rock massif behavior in time.

The origin, source and cycling of methane in deep crystalline rock biosphere

Directory of Open Access Journals (Sweden)

Riikka eKietäväinen

2015-07-01

Full Text Available The emerging interest in using stable bedrock formations for industrial purposes, e.g. nuclear waste disposal, has increased the need for understanding microbiological and geochemical processes in deep crystalline rock environments, including the carbon cycle. Considering the origin and evolution of life on Earth, these environments may also serve as windows to the past. Various geological, chemical and biological processes can influence the deep carbon cycle. Conditions of CH4 formation, available substrates and time scales can be drastically different from surface environments. This paper reviews the origin, source and cycling of methane in deep terrestrial crystalline bedrock with an emphasis on microbiology. In addition to potential formation pathways of CH4, microbial consumption of CH4 is also discussed. Recent studies on the origin of CH4 in continental bedrock environments have shown that the traditional separation of biotic and abiotic CH4 by the isotopic composition can be misleading in substrate-limited environments, such as the deep crystalline bedrock. Despite of similarities between Precambrian continental sites in Fennoscandia, South Africa and North America, where deep methane cycling has been studied, common physicochemical properties which could explain the variation in the amount of CH4 and presence or absence of CH4 cycling microbes were not found. However, based on their preferred carbon metabolism, methanogenic microbes appeared to have similar spatial distribution among the different sites.

The origin, source, and cycling of methane in deep crystalline rock biosphere.

Science.gov (United States)

Kietäväinen, Riikka; Purkamo, Lotta

2015-01-01

The emerging interest in using stable bedrock formations for industrial purposes, e.g., nuclear waste disposal, has increased the need for understanding microbiological and geochemical processes in deep crystalline rock environments, including the carbon cycle. Considering the origin and evolution of life on Earth, these environments may also serve as windows to the past. Various geological, chemical, and biological processes can influence the deep carbon cycle. Conditions of CH4 formation, available substrates and time scales can be drastically different from surface environments. This paper reviews the origin, source, and cycling of methane in deep terrestrial crystalline bedrock with an emphasis on microbiology. In addition to potential formation pathways of CH4, microbial consumption of CH4 is also discussed. Recent studies on the origin of CH4 in continental bedrock environments have shown that the traditional separation of biotic and abiotic CH4 by the isotopic composition can be misleading in substrate-limited environments, such as the deep crystalline bedrock. Despite of similarities between Precambrian continental sites in Fennoscandia, South Africa and North America, where deep methane cycling has been studied, common physicochemical properties which could explain the variation in the amount of CH4 and presence or absence of CH4 cycling microbes were not found. However, based on their preferred carbon metabolism, methanogenic microbes appeared to have similar spatial distribution among the different sites.

Assessment of cortical maturation with prenatal MRI. Part I: normal cortical maturation

Energy Technology Data Exchange (ETDEWEB)

Fogliarini, Celine [Faculte Timone, Centre de Resonance Magnetique Biologique et Medicale, Marseille (France); Chaumoitre, Katia [Hopital Nord, Department of Radiology, Marseille (France); Chapon, Frederique; Levrier, Olivier; Girard, Nadine [Hopital Timone, Department of Neuroradiology, Marseille Cedex 5 (France); Fernandez, Carla; Figarella-Branger, Dominique [Hopital Timone, Department of Pathology, Marseille (France)

2005-08-01

Cortical maturation, especially gyral formation, follows a temporospatial schedule and is a good marker of fetal maturation. Although ultrasonography is still the imaging method of choice to evaluate fetal anatomy, MRI has an increasingly important role in the detection of brain abnormalities, especially of cortical development. Knowledge of MRI techniques in utero with the advantages and disadvantages of some sequences is necessary, in order to try to optimize the different magnetic resonance sequences to be able to make an early diagnosis. The different steps of cortical maturation known from histology represent the background necessary for the understanding of maturation in order to be then able to evaluate brain maturation through neuroimaging. Illustrations of the normal cortical maturation are given for each step accessible to MRI for both the cerebral hemispheres and the posterior fossa. (orig.)

Assessment of cortical maturation with prenatal MRI. Part I: normal cortical maturation

International Nuclear Information System (INIS)

Fogliarini, Celine; Chaumoitre, Katia; Chapon, Frederique; Levrier, Olivier; Girard, Nadine; Fernandez, Carla; Figarella-Branger, Dominique

2005-01-01

Cortical maturation, especially gyral formation, follows a temporospatial schedule and is a good marker of fetal maturation. Although ultrasonography is still the imaging method of choice to evaluate fetal anatomy, MRI has an increasingly important role in the detection of brain abnormalities, especially of cortical development. Knowledge of MRI techniques in utero with the advantages and disadvantages of some sequences is necessary, in order to try to optimize the different magnetic resonance sequences to be able to make an early diagnosis. The different steps of cortical maturation known from histology represent the background necessary for the understanding of maturation in order to be then able to evaluate brain maturation through neuroimaging. Illustrations of the normal cortical maturation are given for each step accessible to MRI for both the cerebral hemispheres and the posterior fossa. (orig.)

Fission track analysis and evolution of mesozoic-paleozoic hydrocarbon resource-rocks headed in Northern Jiangsu-South Yellow sea basin

International Nuclear Information System (INIS)

Xu Hong; Cai Qianzhong; Sun Heqing; Guo Zhenxuan; Yan Guijing; Dai Jing; Liu Dongying

2008-01-01

Fission track data of different geologic epoches from Binhai salient, Yancheng sag, Haian sag, Baiju sag, Gaoyou sag, Hongze sag and Jinhu sag of northern Jiangsu basin and seismic data from Laoshan uplift in South Yellow Sea basin and evolution of Paleozoic hydrocarbon resource-rocks headed in the Northern Jiangsu-South Yellow Sea basin were studied. Results indicate that Binhai salient uplifted in 38-15 Ma, forming 'structure uplifting model', Paleozoic hydrocarbon resource-rocks have the appearance of 'different layers but identical mature, different layers but identical temperature' with Laoshan uplift. All sags have the characters of 'long time heating model', and sedimentations in Cenozoic were exploited by 2 km. Mesozoic-Paleozoic hydrocarbon resource- rocks of Laoshan uplift get ahead of 10 km. Structure evolution was compared with Binhai salient. According to the modeling results of secondary hydrocarbon generation, Mesozoic-Paleozoic hydrocarbon resource-rocks of Laoshan uplift have the good reservoir potentiality and probably become an important new window for sea oil and gas exploration. (authors)

Rock mechanics for hard rock nuclear waste repositories

International Nuclear Information System (INIS)

Heuze, F.E.

1981-09-01

The mined geologic burial of high level nuclear waste is now the favored option for disposal. The US National Waste Terminal Storage Program designed to achieve this disposal includes an extensive rock mechanics component related to the design of the wastes repositories. The plan currently considers five candidate rock types. This paper deals with the three hard rocks among them: basalt, granite, and tuff. Their behavior is governed by geological discontinuities. Salt and shale, which exhibit behavior closer to that of a continuum, are not considered here. This paper discusses both the generic rock mechanics R and D, which are required for repository design, as well as examples of projects related to hard rock waste storage. The examples include programs in basalt (Hanford/Washington), in granitic rocks (Climax/Nevada Test Site, Idaho Springs/Colorado, Pinawa/Canada, Oracle/Arizona, and Stripa/Sweden), and in tuff

Elastic Rock Heterogeneity Controls Brittle Rock Failure during Hydraulic Fracturing

Science.gov (United States)

Langenbruch, C.; Shapiro, S. A.

2014-12-01

For interpretation and inversion of microseismic data it is important to understand, which properties of the reservoir rock control the occurrence probability of brittle rock failure and associated seismicity during hydraulic stimulation. This is especially important, when inverting for key properties like permeability and fracture conductivity. Although it became accepted that seismic events are triggered by fluid flow and the resulting perturbation of the stress field in the reservoir rock, the magnitude of stress perturbations, capable of triggering failure in rocks, can be highly variable. The controlling physical mechanism of this variability is still under discussion. We compare the occurrence of microseismic events at the Cotton Valley gas field to elastic rock heterogeneity, obtained from measurements along the treatment wells. The heterogeneity is characterized by scale invariant fluctuations of elastic properties. We observe that the elastic heterogeneity of the rock formation controls the occurrence of brittle failure. In particular, we find that the density of events is increasing with the Brittleness Index (BI) of the rock, which is defined as a combination of Young's modulus and Poisson's ratio. We evaluate the physical meaning of the BI. By applying geomechanical investigations we characterize the influence of fluctuating elastic properties in rocks on the probability of brittle rock failure. Our analysis is based on the computation of stress fluctuations caused by elastic heterogeneity of rocks. We find that elastic rock heterogeneity causes stress fluctuations of significant magnitude. Moreover, the stress changes necessary to open and reactivate fractures in rocks are strongly related to fluctuations of elastic moduli. Our analysis gives a physical explanation to the observed relation between elastic heterogeneity of the rock formation and the occurrence of brittle failure during hydraulic reservoir stimulations. A crucial factor for understanding

Nutritional compositions and antioxidative capacity of the silk obtained from immature and mature corn

Directory of Open Access Journals (Sweden)

Nurhanan Abdul Rahman

2014-04-01

Full Text Available The silks of immature and mature corn were evaluated for their variations in nutritional compositions, mineral content and antioxidant capacity. Both immature and mature silks were good source of nutritional compositions. Immature silks contained significantly higher moisture (89.31% (fresh basis, lipid (1.27% and protein (12.96% content than the mature silk. Mature silks contained higher composition of ash (5.51%, carbohydrate (29.74% and total dietary fiber (51.25 g/100 g, than the immature silk, but the difference was not significant. In mineral determination, immature silk was rich source of Ca (1087.08 μg/g, Mg (1219.17 μg/g, Cu (5.60 μg/g and Zn (46.37 μg/g than the mature silks. In contrast, other minerals such as K (35671.67 μg/g, Na (266.67 μg/g, Fe (4.50 μg/g and Mn (35.57 μg/g were found higher in the mature silk. The silks were extracted with ethyl acetate, ethanol and water using the Soxhlet extraction method to determine the polyphenol and ABTS radical scavenging capacity. From this study, the highest content of total polyphenol of immature silks was exhibited by ethanol extract (92.21 mg GAE/g while water extract (64.22 mg GAE/g had the highest polyphenol content among mature silk extracts. Total flavonoid content of both immature and mature silks was higher in the water extract at 8.40 mg CAE/g and 2.31 mg CAE/g, respectively. In the ABTS free radical assay method, all immature silk extracts had higher percentage of inhibition compared to the mature silks. Among all three crude extracts, the ethanol extract of immature (EC50 = 0.478 mg/ml and mature silk (EC50 = 0.799 mg/ml exhibited the strongest antioxidant capacity followed by the water and ethyl acetate extract.

Rock.XML - Towards a library of rock physics models

Science.gov (United States)

Jensen, Erling Hugo; Hauge, Ragnar; Ulvmoen, Marit; Johansen, Tor Arne; Drottning, Åsmund

2016-08-01

Rock physics modelling provides tools for correlating physical properties of rocks and their constituents to the geophysical observations we measure on a larger scale. Many different theoretical and empirical models exist, to cover the range of different types of rocks. However, upon reviewing these, we see that they are all built around a few main concepts. Based on this observation, we propose a format for digitally storing the specifications for rock physics models which we have named Rock.XML. It does not only contain data about the various constituents, but also the theories and how they are used to combine these building blocks to make a representative model for a particular rock. The format is based on the Extensible Markup Language XML, making it flexible enough to handle complex models as well as scalable towards extending it with new theories and models. This technology has great advantages as far as documenting and exchanging models in an unambiguous way between people and between software. Rock.XML can become a platform for creating a library of rock physics models; making them more accessible to everyone.

O rock desligado de Lóki

Directory of Open Access Journals (Sweden)

Márcia Carvalho

2012-08-01

Full Text Available This paper presents an analysis of the documentary Loki: ArnaldoBaptista (2009, direct by Paulo Henrique Fontenelle. This analysis investigates thehistorical research and biographical approach, examining in particular the enhancement oforal memory and musical performances from different sources to put into perspective thehistory of Brazilian rock on movie screens and television.

Modelling of nuclear explosions in hard rock sites

International Nuclear Information System (INIS)

Brunish, W.M.; App, F.N.

1993-01-01

This study represents part of a larger effort to systematically model the effects of differing source region properties on ground motion from underground nuclear explosions at the Nevada Test Site. In previous work by the authors the primary emphasis was on alluvium and both saturated and unsaturated tuff. We have attempted to model events on Pahute Mesa, where either the working point medium, or some of the layers above the working point, or both, are hard rock. The complex layering at these sites, however, has prevented us from drawing unambiguous conclusions about modelling hard rock

Effect of concentration of dispersed organic matter on optical maturity parameters. Interlaboratory results of the organic matter concentration working group of the ICCP

Energy Technology Data Exchange (ETDEWEB)

Mendonca Filho, J.G.; Kern, M.L.; Mendonca, J.O. [Palynofacies and Organic Facies Laboratory (LAFO), DEGL, IGEO, UFRJ, Cidade Universitaria, Rio de Janeiro (Brazil); Araujo, C.V.; Menezes, T.R.; Souza, I.V.A.F. [Petrobras R and D Center, Rio de Janeiro (Brazil); Borrego, A.G.; Suarez-Ruiz, I. [Instituto Nacional del Carbon, CSIC, Oviedo (Spain); Cook, A.; Ranasinghe, P. [Keiraville Konsultants Pty. Ltd, NSW (Australia); Flores, D. [University of Porto, Departamento de Geologia (Portugal); Hackley, P. [U.S. Geological Survey, MS 956 National Center Reston, VA (United States); Hower, J.C. [University of Kentucky, Center for Applied Energy Research, Lexington (United States); Kommeren, K. [Shell International Exploration and Production, Rijswijk (Netherlands); Kus, J. [Germany Federal Institute for Geosciences and Natural Resources in Geozentrum, Hannover (Germany); Mastalerz, M. [Indiana Geological Survey, Indiana University, Bloomington (United States); Newman, J. [Newman Energy Research Ltd, Christchurch (New Zealand); Ujiie, Y. [Graduate School of Science and Technology, Hirosaki University (Japan)

2010-12-01

The main objective of this work was to study the effect of the kerogen isolation procedures on maturity parameters of organic matter using optical microscopes. This work represents the results of the Organic Matter Concentration Working Group (OMCWG) of the International Committee for Coal and Organic Petrology (ICCP) during the years 2008 and 2009. Four samples have been analysed covering a range of maturity (low and moderate) and terrestrial and marine geological settings. The analyses comprise random vitrinite reflectance measured on both kerogen concentrate and whole rock mounts and fluorescence spectra taken on alginite. Eighteen participants from twelve laboratories from all over the world performed the analyses. Samples of continental settings contained enough vitrinite for participants to record around 50 measurements whereas fewer readings were taken on samples from marine setting. The scatter of results was also larger in the samples of marine origin. Similar vitrinite reflectance values were in general recorded in the whole rock and in the kerogen concentrate. The small deviations of the trend cannot be attributed to the acid treatment involved in kerogen isolation but to reasons related to components identification or to the difficulty to achieve a good polish of samples with high mineral matter content. In samples difficult to polish, vitrinite reflectance was measured on whole rock tended to be lower. The presence or absence of rock fabric affected the selection of the vitrinite population for measurement and this also had an influence in the average value reported and in the scatter of the results. Slightly lower standard deviations were reported for the analyses run on kerogen concentrates. Considering the spectral fluorescence results, it was observed that the {lambda}max presents a shift to higher wavelengths in the kerogen concentrate sample in comparison to the whole-rock sample, thus revealing an influence of preparation methods (acid treatment

Pre-earthquake signals – Part I: Deviatoric stresses turn rocks into a source of electric currents

Directory of Open Access Journals (Sweden)

F. T. Freund

2007-09-01

Full Text Available Earthquakes are feared because they often strike so suddenly. Yet, there are innumerable reports of pre-earthquake signals. Widespread disagreement exists in the geoscience community how these signals can be generated in the Earth's crust and whether they are early warning signs, related to the build-up of tectonic stresses before major seismic events. Progress in understanding and eventually using these signals has been slow because the underlying physical process or processes are basically not understood. This has changed with the discovery that, when igneous or high-grade metamorphic rocks are subjected to deviatoric stress, dormant electronic charge carriers are activated: electrons and defect electrons. The activation increases the number density of mobile charge carriers in the rocks and, hence, their electric conductivity. The defect electrons are associated with the oxygen anion sublattice and are known as positive holes or pholes for short. The boundary between stressed and unstressed rock acts a potential barrier that lets pholes pass but blocks electrons. Therefore, like electrons and ions in an electrochemical battery, the stress-activated electrons and pholes in the "rock battery" have to flow out in different directions. When the circuit is closed, the battery currents can flow. The discovery of such stress-activated currents in crustal rocks has far-reaching implications for understanding pre-earthquake signals.

Petroleum Systems and Assessment of Undiscovered Oil and Gas in the Raton Basin - Sierra Grande Uplift Province, Colorado and New Mexico - USGS Province 41

Science.gov (United States)

Higley, Debra K.

2007-01-01

Introduction The purpose of the U.S. Geological Survey's (USGS) National Oil and Gas Assessment is to develop geologically based hypotheses regarding the potential for additions to oil and gas reserves in priority areas of the United States. The USGS recently completed an assessment of undiscovered oil and gas resources of the Raton Basin-Sierra Grande Uplift Province of southeastern Colorado and northeastern New Mexico (USGS Province 41). The Cretaceous Vermejo Formation and Cretaceous-Tertiary Raton Formation have production and undiscovered resources of coalbed methane. Other formations in the province exhibit potential for gas resources and limited production. This assessment is based on geologic principles and uses the total petroleum system concept. The geologic elements of a total petroleum system include hydrocarbon source rocks (source rock maturation, hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). The USGS used this geologic framework to define two total petroleum systems and five assessment units. All five assessment units were quantitatively assessed for undiscovered gas resources. Oil resources were not assessed because of the limited potential due to levels of thermal maturity of petroleum source rocks.

Rock burst governance of working face under igneous rock

Science.gov (United States)

Chang, Zhenxing; Yu, Yue

2017-01-01

As a typical failure phenomenon, rock burst occurs in many mines. It can not only cause the working face to cease production, but also cause serious damage to production equipment, and even result in casualties. To explore how to govern rock burst of working face under igneous rock, the 10416 working face in some mine is taken as engineering background. The supports damaged extensively and rock burst took place when the working face advanced. This paper establishes the mechanical model and conducts theoretical analysis and calculation to predict the fracture and migration mechanism and energy release of the thick hard igneous rock above the working face, and to obtain the advancing distance of the working face when the igneous rock fractures and critical value of the energy when rock burst occurs. Based on the specific conditions of the mine, this paper put forward three kinds of governance measures, which are borehole pressure relief, coal seam water injection and blasting pressure relief.

Determination of radioactivity in Chinese phosphate rock and fertilizer

International Nuclear Information System (INIS)

Chen Jingjian; Zhu Yongyi; Yang Juncheng

1993-01-01

The presented paper reported the radioactivity of U-238, Ra-226, Th-232 and K-40 in Chinese phosphate rocks by gamma spectrographic analysis during 1985-1990. The results showed that the decay chain of U-238-Ra-226 was the main source of radionuclides in phosphate rocks. The radionuclides in phosphate fertilizer differed from the forms of phosphate fertilizer. U-238 was the most important radionuclide in phosphoric compound fertilizer. The transfer rate of radionuclides was also estimated. (2 figs., 1 tab.)

Water-rock-tailings interactions and sources of sulfur and metals in the subtropical mining region of Taxco, Guerrero (southern Mexico): A multi-isotopic approach

International Nuclear Information System (INIS)

Talavera Mendoza, Oscar; Ruiz, Joaquin; Díaz Villaseñor, Elvia; Ramírez Guzmán, Alejandro; Cortés, Alejandra; Salgado Souto, Sergio Adrián; Dótor Almazán, Azucena; Rivera Bustos, Reymundo

2016-01-01

Multi-isotope (H, O, S, Sr, Pb) systems coupled with conventional (major and trace element) hydrogeochemical analysis were applied to determine the origin of water, to model water-rock-tailings interactions and for source apportionment of sulfur and associated toxic metals in the mining region of Taxco, Guerrero in southern Mexico. Oxygen and H isotopes indicate that meteoric water in the zone is rainwater undergoing varying degrees of isotopic fractionation by atmospheric evaporation whereas Sr isotopes trace the interaction of pristine water from volcanics of the regional recharge zone and subsequently flowing through sandstone and shale to spring points. Leachates form from two distinctive sources (spring water and surface water) having differential interactions with bedrocks prior to entering the tailings. Compared to pristine water, leachates are enriched in sulfate, metals (e.g. Fe, Mn, Pb and Zn) and metalloids (e.g. As). The sulfur isotopic composition of ore-sulfides, leachates, secondary precipitates, regional surface water and hypogenic sulfates is described in terms of a two-component mixing model with shale of Mexcala and limestone of Morelos formations representing the light and heavy end-members, respectively, whereas Sr isotopic composition is bracketed combining three lithogenic (Mexcala/Morelos, Tilzapotla and Taxco Schist) sources. Finally, leachates have a mixture of lead from ore-sulfides and Taxco Schist Formation (Family I) or from ore-sulfides alone (Family II). The application of multiple environmental isotopic techniques is an outstanding tool for elucidating complex interactions of water with bedrocks and tailings and for determining the source of sulfur and toxic metal from mining and other metal polluted environments. - Highlights: • We applied multi-isotope techniques to model water-bedrocks-tailings interaction. • Spring water records fractionation by evaporation and interaction with local rocks. • The sulfur cycle is modeled in

The Australian national reactive phosphate rock project - Aims, experimental approach, and site characteristics

International Nuclear Information System (INIS)

McLaughlin, M.J.

2002-01-01

Field-based cutting trials were established across Australia in a range of environments to evaluate the agronomic effectiveness of 5 phosphate rocks, and 1 partially acidulated phosphate rock, relative to either single super-phosphate or triple superphosphate. The phosphate rocks differed in reactivity, as determined by the degree of carbonate substitution for phosphate in the apatite structure and solubility of phosphorus present in the fertilizers in 2% formic acid, 2% citric acid and neutral ammonium citrate. Sechura (Bayovar) and North Carolina phosphate rocks were highly reactive (>70% solubility in 2% formic acid), whilst Khouribja (Moroccan) and Hamrawein (Egypt) phosphate rock were moderately reactive. Duchess phosphate rock from Queensland was relatively unreactive ( 2 , from 4.0 to 5.1, and Colwell extractable phosphorus ranged from 3 to 47 μg/g prior to fertilizer application. Two core experiments were established at each site. The first measured the effects of phosphate rock reactivity on agronomic effectiveness, while the second core experiment measured the effects of the degree of water solubility of the phosphorus source on agronomic effectiveness. The National Reactive Phosphate Rock Project trials provided the opportunity to confirm the suitability of accepted procedures to model fertilizer response and to develop new approaches for comparing different fertilizer responses. The Project also provided the framework for subsidiary studies such as the effect of fertilizer source on soil phosphorus extractability; cadmium and fluorine concentrations in herbage; evaluation of soil phosphorus tests; and the influence of particle size on phosphate rock effectiveness. The National Reactive Phosphate Rock Project presents a valuable model for a large, Australia-wide, collaborative team approach to an important agricultural issue. The use of standard and consistent experimental methodologies at every site ensured that maximum benefit was obtained from data

A computer-assisted rock type data catalogue for gas formations; Ein rechnergestuetzter Gesteinsdatenkatalog fuer Gasformationen

Energy Technology Data Exchange (ETDEWEB)

Reitenbach, V.; Pusch, G.; Moeller, M.; Koll, S. [TU Clausthal (Germany). Inst. fuer Erdoel- und Erdgastechnik; Constantini, A.; Junker, A.; Anton, H. [RWE Dea AG, Hamburg (Germany)

2007-09-13

Modern reservoir management commonly requires versatile reservoir data which are neces-sary for integrated reservoir characterization, evaluation and development planning. The rock data necessary for numerical reservoir simulation studies often have to be collected from different sources, analysed and sorted with a considerable effort. In a framework of DGMK research program (DGMK project 593-9/4), the Institute of Petro-leum Engineering (Clausthal University of Technology) and RWE DEA AG have developed a new tool named Rock Data Catalogue, which is capable of managing large amounts of rock data more efficiently and deriving new specific correlations for European rock types. The use of Rock Data Catalogue can facilitate the essential input data generation and proc-essing procedure for reservoir simulation studies. The Rock Data Catalogue is comprised of a Data Base Module of digitalized reservoir rock data and an interactive Data Correlation Module. Both modules are built-up as an interface to common reservoir simulation software. The universal structure of the software also makes it possible to exchange the data with other rock data information systems. The Data Correlation Module implements a ''Decision-Structure'' module, which helps the reservoir engineer to select the rock data for analysis and correlation depending on its litho-facial type and permeability class. The Data Base Module enables a quick search of appro-priated data sets and their export into the correlation module. The open source data of the North German Rotliegend gas formations as well as the data of measurements on Rotliegend core samples performed at the ITE in course of the DGMK tight gas projects were implemented in the rock data base. Correlations of poro/perm data, two-phase flow and capillary pressure functions of the Rotliegend sandstones with the per-meability range between 20 and 0.01 mD are implemented in the rock data base and serve for quality checking of the

Ore potential of basic rocks in Finland

International Nuclear Information System (INIS)

Reino, J.; Ekberg, M.; Heinonen, P.; Karppanen, T.; Hakapaeae, A.; Sandberg, E.

1993-02-01

The report is associated with a study programme on basic rocks, which has the aim to complement the preliminary site investigations on repository for TVO's (Teollisuuden Voima Oy) spent nuclear fuel. The report comprises a mining enterprise's view of the ore potential of basic plutonic rocks in Finland. The ores associated with basic plutonic rocks are globally known and constitute a significant share of the global mining industry. The ores comprise chromium, vanadium-titanium-iron, nickel-copper and platinum group element ores. The resources of the metals in question and their mining industry are examined globally. A review of the use of these metals in the industry is presented as well. General factors affecting the mining industry, such as metal prices, political conjunctures, transport facilities, environmental requirements and raw material sources for the Finnish smelters have been observed from the point of view of their future effect on exploration activity and industrial development in Finland. Information on ores and mineralizations associated with Finnish basic rocks have been compiled in the report. The file comprises 4 chromium occurrences, 8 vanadium-titanium-iron occurrences, 13 PGE occurrences and 38 nickel-copper occurrences

Nd and Sr isotopes and K-Ar ages of the Ulreungdo alkali volcanic rocks in the East Sea, South Korea

International Nuclear Information System (INIS)

Kim Kyuhan; Jang Sunkyung; Tanaka, Tsuyoshi; Nagao, Keisuke

1999-01-01

Temporal geochemical and isotopical variations in the Ulreundgo alkali volcanic rocks provide important constraints on the origin and evolution of the volcanic rocks in relation to backarc basin tectonism. We determined the K-Ar ages, major and trace element contents, and Nd and Sr isotopic rations of the alkali volcanic rocks. The activities of Ulreungdo volcanoes can be divided, on the basis of radiometric ages and field occurrences, into five stages, though their activities range from 1.4 Ma to 0.01 Ma with short volcanic hiatus (ca. 0.05-0.3 Ma). The Nd-Sr isotopic data for Ulreungdo volcanic rocks enable us to conclude that: (1) the source materials of Ulreungdo volcanics are isotopically heterogeneous in composition, which is explained by the mixing of mantle derived magma and continental crustal source rocks. There is no systematic isotopic variations with eruption stages. Particularly, some volcanic rocks of stage 2 and 3 have extremely wide initial 87 Sr/ 86 Sr isotopic variations ranging from 0.7038 to 0.7092, which are influenced by seawater alterations; (2) the Ulreungdo volcanic rocks show EMI characteristic, while volcanic rocks from the Jejudo, Yeong-il and Jeon-gok areas have slightly depleted mantle source characteristics; (3) the trachyandesite of the latest eruption stage was originated from the mantle source materials which differ from other stages. A schematic isotopic evolution model for alkali basaltic magma is presented in the Ulreungdo volcanic island of the backarc basin of Japanese island arc system. (author)

Assessing healthcare process maturity: challenges of using a business process maturity model

NARCIS (Netherlands)

Tarhan, A.; Turetken, O.; van den Biggelaar, F.J.H.M.

2015-01-01

Doi: 10.4108/icst.pervasivehealth.2015.259105 The quality of healthcare services is influenced by the maturity of healthcare processes used to develop it. A maturity model is an instrument to assess and continually improve organizational processes. In the last decade, a number of maturity models

For Those About to Rock : Naislaulajat rock-genressä

OpenAIRE

Herranen, Linda

2015-01-01

For those about to rock – naislaulajat rock-genressä antaa lukijalleen kokonaisvaltaisen käsityksen naisista rock-genressä: rockin historiasta, sukupuolittuneisuudesta, seksismistä, suomalaisten naislaulajien menestyksestä. Työn aineisto on koottu aihepiirin kirjallisuudesta ja alalla toimiville naislaulajille teetettyjen kyselyiden tuloksista. Lisäksi avaan omia kokemuksiani ja ajatuksiani, jotta näkökulma naisista rock-genressä tulisi esille mahdollisimman monipuolisesti. Ajatus aihees...

Diagnostic assessment of skeletal maturity through dental maturation in Hispanic growing individuals

Directory of Open Access Journals (Sweden)

Alejandra Cisternas

2017-01-01

Full Text Available Background: The aim of this study was to explore dental maturation as a diagnostic test for skeletal maturation. Materials and Methods: Six hundred and fifty-seven growing individuals were classified according to their cervical vertebral maturity and dental maturity, both determined in lateral cephalograms and panoramic radiographs, respectively. The correlation between cervical and dental stages was established for each gender. A receiver operating characteristic curve analysis was made, and sensitivity and specificity values were established. Results: Correlation was found between cervical and dental maturation for females (r = 0.73; P<0.001 and males (r = 0.60; P<0.001. Sensitivity for dental Stage F, as an indicator of a postmaturation peak stage, was 87.21% for females and 97.1% for males, whereas specificity for the same stage was 82.92% and 72.3% for females and males, respectively. Conclusions: Dental maturation evaluation could contribute determining whether a patient is in a pre- or post-growth spurt stage.

Proceedings of the 3. Canada-US rock mechanics symposium and 20. Canadian rock mechanics symposium : rock engineering 2009 : rock engineering in difficult conditions

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-07-01

This conference provided a forum for geologists, mining operators and engineers to discuss the application of rock mechanics in engineering designs. Members of the scientific and engineering communities discussed challenges and interdisciplinary elements involved in rock engineering. New geological models and methods of characterizing rock masses and ground conditions in underground engineering projects were discussed along with excavation and mining methods. Papers presented at the conference discussed the role of rock mechanics in forensic engineering. Geophysics, geomechanics, and risk-based approaches to rock engineering designs were reviewed. Issues related to high pressure and high flow water conditions were discussed, and new rock physics models designed to enhance hydrocarbon recovery were presented. The conference featured 84 presentations, of which 9 have been catalogued separately for inclusion in this database. tabs., figs.

Emplacement of rock avalanche material across saturated sediments, Southern Alp, New Zealand

Science.gov (United States)

Dufresne, A.; Davies, T. R.; McSaveney, M. J.

2012-04-01

The spreading of material from slope failure events is not only influenced by the volume and nature of the source material and the local topography, but also by the materials encountered in the runout path. In this study, evidence of complex interactions between rock avalanche and sedimentary runout path material were investigated at the 45 x 106 m3 long-runout (L: 4.8 km) Round Top rock avalanche deposit, New Zealand. It was sourced within myolinitic schists of the active strike-slip Alpine Fault. The narrow and in-failure-direction elongate source scarp is deep-seated, indicating slope failure was triggered by strong seismic activity. The most striking morphological deposit features are longitudinal ridges aligned radially to source. Trenching and geophysical surveys show bulldozed and sheared substrate material at ridge termini and laterally displaced sedimentary strata. The substrate failed at a minimum depth of 3 m indicating a ploughing motion of the ridges into the saturated material below. Internal avalanche compression features suggest deceleration behind the bulldozed substrate obstacle. Contorted fabric in material ahead of the ridge document substrate disruption by the overriding avalanche material deposited as the next down-motion hummock. Comparison with rock avalanches of similar volume but different emplacement environments places Round Top between longer runout avalanches emplaced over e.g. playa lake sediments and those with shorter travel distances, whose runout was apparently retarded by topographic obstacles or that entrained high-friction debris. These empirical observations indicate the importance of runout path materials on tentative trends in rock avalanche emplacement dynamics and runout behaviour.

Fundamental observations concerning hysteresis in the deformation of intact and jointed rock with applications to nonlinear attenuation in the near source region

International Nuclear Information System (INIS)

Boitnott, G.N.

1993-01-01

In order to estimate yields of large underground explosions, it is important that we have a clear understanding of the near source phenomena and their effects on regional and teleseismic signals. While it is generally accepted that a considerable amount of attenuation and resultant waveform distortion occurs due to nonlinear deformation near the source, an area that has received little attention is the broad enveloping region where moderate stress perturbations occur. In this region, where strain perturbation amplitudes range from microstrains to a few millistrains, the resulting deformation of rock is inelastic and nonlinear but little to no permanent deformation results. Owing to its great extent, the moderate strain regime has the potential to influence the entire frequency band of the regional and teleseismic signals and thus may be central to the problem of inferring source characteristics from far field signals. Detailed rheological descriptions are required in order to understand the effects of the nonlinearities on the spectral content of regional and teleseismic signals

Using pattern classification and nuclear forensic signatures to link UOC to source rocks and purification processes

International Nuclear Information System (INIS)

Marks, N.; Robel, M.; Borg, M.; Hutcheon, I.; Kristo, M.

2014-01-01

Nuclear forensics is a scientific discipline interfacing law enforcement, nuclear science and nonproliferation. Information on the history and on the potential origin of unknown nuclear material can be obtained through nuclear forensic analysis. Using commonly available techniques of mass spectrometry, microscopy and x-ray diffraction, we have gained insight into the processing and origin of a suite of uranium ore concentrate (UOC) samples. We have applied chemometric techniques to investigate the relationships between uranium ore deposits and UOC samples in order to identify chemical and isotopic signatures of nuclear forensic importance. We developed multivariate signatures based on elemental concentrations and isotope ratios using a database of characteristics of UOC originating throughout the world. By introducing detailed and specific information about the source rock geology for each sample, we improved our understanding of the preservation of forensic signatures in UOC. Improved characterization of sample processing and provenance allows us to begin to assess the statistical significance of different groupings of samples and identify underlying patterns. Initial results indicate the concentration of uranium in the ore body, the geochemical conditions associated with uranium emplacement, and host rock petrogenesis exert controlling influences on the impurities preserved in UOC. Specific ore processing techniques, particularly those related to In-Situ Recovery, are also reflected in UOC impurity signatures. Stable and radiogenic isotope geochemistry can be used in conjunction with rare earth element patterns and other characteristics to link UOCs to specific geologic deposits of origin. We will present a number of case studies illustrating the ways in which nuclear forensic analysis can provide insight into the ore geology and production and purification processes used to produce UOC. (author)

Correlation between Dental Maturity by Demirjian Method and Skeletal Maturity by Cervical Vertebral Maturity Method using Panoramic Radiograph and Lateral Cephalogram

Directory of Open Access Journals (Sweden)

Madhusudhanan Mallika Mini

2017-01-01

Full Text Available Introduction: Radiographs are effective tools in assessing the stages of bone maturation in dentistry. The cervical vertebral maturation method is a proven effective tool in assessing the adolescent growth spurt than hand-wrist radiographs in an individual. Assessment of dental calcification stages are a reliable method for determining dental maturity. Panoramic imaging can be used as the primary imaging modality for assessing maturity if a correlation can be found out between tooth calcification stages and cervical vertebral maturation stages. This study was conducted to determine the correlation between dental maturity stage and cervical vertebral maturity stage and to estimate predictor variables for cervical vertebral maturation stages (CVMS stratified by gender in a tertiary hospital setting. Materials and Methods: A descriptive study was conducted among patients accessing orthodontic care in radiology outpatient clinic, Oral Medicine and Radiology department, Government Dental College Thiruvananthapuram for a period of 15 months. Participants were selected between the ages of 8 and 16 years. Panoramic radiographs and lateral cephalograms were used to determine dental maturity stages using Demirjian method and CVMS using Bacetti and Franchi method, respectively. Results: One hundred patients (males = 46, females = 54 were included in the study; the spearman rank order correlation revealed significant relationship. The correlation ranged from 0.61 to 0.74 for females and 0.48 to 0.51 for males. Second premolar showed highest correlation and canine the lowest for both females and males. Stage G of mandibular second premolar signifies the pubertal growth period in this study population. By ordinal regression model, G stage of second premolar was found to be a significant predictor in males and stage H followed by G and F in females for the age group of 12–14 years. Conclusion: Dental maturation stages were significantly correlated with CVMS

Art Rocks with Rock Art!

Science.gov (United States)

Bickett, Marianne

2011-01-01

This article discusses rock art which was the very first "art." Rock art, such as the images created on the stone surfaces of the caves of Lascaux and Altimira, is the true origin of the canvas, paintbrush, and painting media. For there, within caverns deep in the earth, the first artists mixed animal fat, urine, and saliva with powdered minerals…

Hydrocarbon occurrence in NW Africa's MSGBC area

Energy Technology Data Exchange (ETDEWEB)

Reymond, A.; Negroni, P.

1989-06-01

The MSGBC (Mauritania, Senegal, The Gambia, Guinea-Bissau, Guinea Conakry) coastal basin has evolved as a passive margin from Jurassic time up to the present following a period of poorly known rifting of Permian to Middle Jurassic age. Structural configuration of the Paleozoic series is documented by large outcrops and a good number of seismic sections. Based on previous exploration efforts that found significant hydrocarbon shows, a comprehensive study of this African basin's source rocks, maturation evolution and petroleum generation potential was undertaken. About 1,000 geochemical analyses of the Paleozoic, Cretaceous and Tertiary series identified good source rocks in the Cenomano-Turonian, Silurian, Senonian and Paleocene ages. The parameters used to identify and characterize source rock are: Total organic carbon content (TOC) in percent and source potential (in kg HC/t), representing the amount of hydrocarbon generated per ton of rock and determined by Rock-Eval pyrolysis.

Asymptotic weight and maturing rate in mice selected for body conformation

Directory of Open Access Journals (Sweden)

Di Masso Ricardo J.

2000-01-01

Full Text Available Growth patterns of four lines of mice selected for body conformation were analyzed with the logistic function, in order to provide baseline information about the relationship between asymptotic weight and maturing rate of body weight. Two lines were divergently selected favoring the phenotypic correlation between body weight and tail length (agonistic selection: CBi+, high body weight and long tail; CBi-, low body weight and short tail, whereas the other two lines were generated by a disruptive selection performed against the correlation between the aforementioned traits (antagonistic selection: CBi/C, high body weight and short tail; CBi/L, low body weight and long tail. The logistic parameters A (asymptotic weight and k (maturing rate behaved in CBi/C and CBi- mice and in CBi+ females as expected in terms of the negative genetic relationship between mature size and earliness of maturing. An altered growth pattern was found in CBi/L mice and in CBi+ males, because in the former genotype, selected for low body weight, the time taken to mature increased, whereas in the latter, selected for high body weight, there was a non-significant increase in the same trait. In accordance with the selective criterion, different sources of genetic variation for body weight could be exploited: one inversely associated with earliness of maturing (agonistic selection, and the other independent of maturing rate (antagonistic selection, showing that genetic variation of A is partly independent of k.

Characterization of some sedimentary sequences from Cambay basin, India, by pyrolysis-GC

Science.gov (United States)

Philp, R. P.; Garg, A. K.

Pyrolysis-gas chromatography of sedimentary sequences from a key exploratory well of the southern Cambay Basin, India, has been performed to characterize the nature of the source material and its maturity. In samples from the Eocene-Paleocene section (2960-3407 m), the pyrolysate is dominated by hydrocarbons in the lower molecular weight region indicating a significant input algal source material. The presence of various xylenes and phenols in the pyrograms is indicative of a significant input from higher plant material. The organic material in this section is interpreted to have been derived from marine-terrestrial source inputs deposited under swampy to marine and reducing environments. Good mature source rocks with type III kerogens which are wet gas/gas condensate-prone have been identified in this region. This paper intends to discuss the characterization of source rocks using the pyrolysis-gas chromatography approach and the significance of the distribution of the pyrolysis product.

Mechanical weathering and rock erosion by climate-dependent subcritical cracking

Science.gov (United States)

Eppes, Martha-Cary; Keanini, Russell

2017-06-01

This work constructs a fracture mechanics framework for conceptualizing mechanical rock breakdown and consequent regolith production and erosion on the surface of Earth and other terrestrial bodies. Here our analysis of fracture mechanics literature explicitly establishes for the first time that all mechanical weathering in most rock types likely progresses by climate-dependent subcritical cracking under virtually all Earth surface and near-surface environmental conditions. We substantiate and quantify this finding through development of physically based subcritical cracking and rock erosion models founded in well-vetted fracture mechanics and mechanical weathering, theory, and observation. The models show that subcritical cracking can culminate in significant rock fracture and erosion under commonly experienced environmental stress magnitudes that are significantly lower than rock critical strength. Our calculations also indicate that climate strongly influences subcritical cracking—and thus rock weathering rates—irrespective of the source of the stress (e.g., freezing, thermal cycling, and unloading). The climate dependence of subcritical cracking rates is due to the chemophysical processes acting to break bonds at crack tips experiencing these low stresses. We find that for any stress or combination of stresses lower than a rock's critical strength, linear increases in humidity lead to exponential acceleration of subcritical cracking and associated rock erosion. Our modeling also shows that these rates are sensitive to numerous other environment, rock, and mineral properties that are currently not well characterized. We propose that confining pressure from overlying soil or rock may serve to suppress subcritical cracking in near-surface environments. These results are applicable to all weathering processes.

The origin of oil in the Cretaceous succession from the South Pars Oil Layer of the Persian Gulf

Science.gov (United States)

Rahmani, Omeid; Aali, Jafar; Junin, Radzuan; Mohseni, Hassan; Padmanabhan, Eswaran; Azdarpour, Amin; Zarza, Sahar; Moayyed, Mohsen; Ghazanfari, Parviz

2013-07-01

The origin of the oil in Barremian-Hauterivian and Albian age source rock samples from two oil wells (SPO-2 and SPO-3) in the South Pars oil field has been investigated by analyzing the quantity of total organic carbon (TOC) and thermal maturity of organic matter (OM). The source rocks were found in the interval 1,000-1,044 m for the Kazhdumi Formation (Albian) and 1,157-1,230 m for the Gadvan Formation (Barremian-Hauterivian). Elemental analysis was carried out on 36 samples from the source rock candidates (Gadvan and Kazhdumi formations) of the Cretaceous succession of the South Pars Oil Layer (SPOL). This analysis indicated that the OM of the Barremian-Hauterivian and Albian samples in the SPOL was composed of kerogen Types II and II-III, respectively. The average TOC of analyzed samples is less than 1 wt%, suggesting that the Cretaceous source rocks are poor hydrocarbon (HC) producers. Thermal maturity and Ro values revealed that more than 90 % of oil samples are immature. The source of the analyzed samples taken from Gadvan and Kazhdumi formations most likely contained a content high in mixed plant and marine algal OM deposited under oxic to suboxic bottom water conditions. The Pristane/nC17 versus Phytane/nC18 diagram showed Type II-III kerogen of mixture environments for source rock samples from the SPOL. Burial history modeling indicates that at the end of the Cretaceous time, pre-Permian sediments remained immature in the Qatar Arch. Therefore, lateral migration of HC from the nearby Cretaceous source rock kitchens toward the north and south of the Qatar Arch is the most probable origin for the significant oils in the SPOL.

Geochemical typification of kimberlite and related rocks of the North Anabar region, Yakutia

Science.gov (United States)

Kargin, A. V.; Golubeva, Yu. Yu.

2017-11-01

The results of geochemical typification of kimberlites and related rocks (alneites and carbonatites) of the North Anabar region are presented with consideration of the geochemical specification of their source and estimation of their potential for diamonds. The content of representative trace elements indicates the predominant contribution of an asthenospheric component (kimberlites and carbonatites) in their source, with a subordinate contribution of vein metasomatic formations containing Cr-diopside and ilmenite. A significant contribution of water-bearing potassium metasomatic parageneses is not recognized. According to the complex of geochemical data, the studied rocks are not industrially diamondiferous.

Differentiation of Spermatogonia Stem Cells into Functional Mature Neurons Characterized with Differential Gene Expression.

Science.gov (United States)

Bojnordi, Maryam Nazm; Azizi, Hossein; Skutella, Thomas; Movahedin, Mansoureh; Pourabdolhossein, Fereshteh; Shojaei, Amir; Hamidabadi, Hatef Ghasemi

2017-09-01

Transplantation of embryonic stem cells (ESCs) is a promising therapeutic approach for the treatment of neurodegenerative diseases. However, ESCs are not usable clinically due to immunological and ethical limitations. The identification of an alternative safe cell source opens novel options via autologous transplantation in neuro-regeneration circumventing these problems. Here, we examined the neurogenic capacity of embryonic stem-like cells (ES-like cells) derived from the testis using neural growth factor inducers and utilized them to generate functional mature neurons. The neuronal differentiation of ES-like cells is induced in three stages. Stage 1 is related to embryoid body (EB) formation. To induce neuroprogenitor cells, EBs were cultured in the presence of retinoic acid, N 2 supplement and fibroblast growth factor followed by culturing in a neurobasal medium containing B 27 , N 2 supplements for additional 10 days, to allow the maturation and development of neuronal progenitor cells. The neurogenic differentiation was confirmed by immunostaining for markers of mature neurons. The differentiated neurons were positive for Tuj1 and Tau1. Real-time PCR dates indicated the expression of Nestin and Neuro D (neuroprogenitor markers) in induced cells at the second stage of the differentiation protocol. The differentiated mature neurons exhibited the specific neuron markers Map2 and β-tubulin. The functional maturity of neurons was confirmed by an electrophysiological analysis of passive and active neural membrane properties. These findings indicated a differentiation capacity of ES-like cells derived from the testis to functionally mature neurons, which proposes them as a novel cell source for neuroregenerative medicine.

EFFECT OF ALTERNATIVE MULTINUTRIENT SOURCES ON SOIL CHEMICAL PROPERTIES

Directory of Open Access Journals (Sweden)

Vanessa Martins

2015-02-01

Full Text Available The current high price of potassium chloride and the dependence of Brazil on imported materials to supply the domestic demand call for studies evaluating the efficiency of alternative sources of nutrients. The aim of this work was to evaluate the effect of silicate rock powder and a manganese mining by-product, and secondary materials originated from these two materials, on soil chemical properties and on brachiaria production. This greenhouse experiment was conducted in pots with 5 kg of soil (Latossolo Vermelho-Amarelo distrófico - Oxisol. The alternative nutrient sources were: verdete, verdete treated with NH4OH, phonolite, ultramafic rock, mining waste and the proportion of 75 % of these K fertilizers and 25 % lime. Mixtures containing 25 % of lime were heated at 800 ºC for 1 h. These sources were applied at rates of 0, 150, 300, 450 and 600 kg ha-1 K2O, and incubated for 45 days. The mixtures of heated silicate rocks with lime promoted higher increases in soil pH in decreasing order: ultramafic rock>verdete>phonolite>mining waste. Applying the mining waste-lime mixture increased soil exchangeable K, and available P when ultramafic rock was incorporated. When ultramafic rock was applied, the release of Ca2+ increased significantly. Mining subproduct released the highest amount of Zn2+ and Mn2+ to the soil. The application of alternative sources of K, with variable chemical composition, altered the nutrient availability and soil chemical properties, improving mainly plant development and K plant uptake, and are important nutrient sources.

Recovery of uranium from low-grade sandstone ores and phosphate rock

Energy Technology Data Exchange (ETDEWEB)

Kennedy, R H [United States Atomic Energy Commission, Washington, D. C. (United States)

1967-06-15

This paper is concerned principally with commercial-scale experience in the United States in the recovery of uranium from low-grade sources. Most of these operations have been conducted by the operators of uranium mills as an alternative to processing normal-grade ores. The operations have been generally limited, therefore, to the treatment of low-grade materials generated in the course of mining normal-grade ores. In some circumstances such materials can be treated by simplified procedures as an attractive source of additional production. The experience gained in uranium recovery from phosphate rock will be treated in some detail. The land pebble phosphate rock of central Florida generally contains about 0.01 to 0.02% U{sub 3}O{sub 8}. While no uranium is being recovered from this source at the present time, it does represent a significant potential source of by-product uranium production because of the large tonnages being mined. (author)

RADIATION CHEMICAL CONVERSION OF OIL DERIVED FROM OIL-BITUMEN ROCK

Directory of Open Access Journals (Sweden)

Lala Jabbarova

2014-06-01

Full Text Available The results of research in the radiation processing of synthetic oil derived from oil–bitumen rock of the Balakhany deposit in Azerbaijan are presented. The study has been conducted on a 60Co gamma-source at a dose rate of P = 0.5 Gy/s and various absorbed doses of D = 43–216 kGy. Samples of synthetic oil from natural bitumen rocks have been analyzed by chromatography, gas chromatography–mass spectrometry, and IR-spectroscopy, and their radiation resistance has been evaluated. The results of the study allow for both assessment of the feasibility of manufacturing petrochemicals for various applications by radiation processing and use of these materials for isolating radioactive sources to preclude their impact on the environment.

The Usability of Rock-Like Materials for Numerical Studies on Rocks

Science.gov (United States)

Zengin, Enes; Abiddin Erguler, Zeynal

2017-04-01

The approaches of synthetic rock material and mass are widely used by many researchers for understanding the failure behavior of different rocks. In order to model the failure behavior of rock material, researchers take advantageous of different techniques and software. But, the majority of all these instruments are based on distinct element method (DEM). For modeling the failure behavior of rocks, and so to create a fundamental synthetic rock material model, it is required to perform related laboratory experiments for providing strength parameters. In modelling studies, model calibration processes are performed by using parameters of intact rocks such as porosity, grain size, modulus of elasticity and Poisson ratio. In some cases, it can be difficult or even impossible to acquire representative rock samples for laboratory experiments from heavily jointed rock masses and vuggy rocks. Considering this limitation, in this study, it was aimed to investigate the applicability of rock-like material (e.g. concrete) to understand and model the failure behavior of rock materials having complex inherent structures. For this purpose, concrete samples having a mixture of %65 cement dust and %35 water were utilized. Accordingly, intact concrete samples representing rocks were prepared in laboratory conditions and their physical properties such as porosity, pore size and density etc. were determined. In addition, to acquire the mechanical parameters of concrete samples, uniaxial compressive strength (UCS) tests were also performed by simultaneously measuring strain during testing. The measured physical and mechanical properties of these extracted concrete samples were used to create synthetic material and then uniaxial compressive tests were modeled and performed by using two dimensional discontinuum program known as Particle Flow Code (PFC2D). After modeling studies in PFC2D, approximately similar failure mechanism and testing results were achieved from both experimental and

Natural analogue for storage of radwaste in crystalline rocks

International Nuclear Information System (INIS)

Brookins, D.G.; Abashian, M.S.; Cohen, L.H.; Wollenberg, H.A. Jr.

1982-01-01

The Bryan-Eldora stock (Colorado) intruded the Precambrian Idaho Springs Formation metamorphic rocks 58 million years ago. Geochronologic-geochemical work by Hart et al. [S.R. Hart et al., in Radiometric Dating for Geologists, E.I. Hamilton, R.S. Farquhar, eds. (Wiley-Interscience, New York, 1968) pp. 73-110] has demonstrated that the heat from the cooling intrusive rocks was sufficient to affect mineral isotopic systematics up to 2000 m from the contact, and the nature of these isotopic perturbations can be explained by a simple diffusion model in turn based on various heat flow models. Our new studies are focused on elemental exchange between stock and intruded rock as a function of distance from the contact; the assumption is made that the stock is a very large, high heat source analogous to a waste form emplaced in the metamorphic rocks without benefit of canister or engineered backfill. Data for U, Th and the REE indicate actinide and lanthanide immobility except perhaps in the 0 to 2m contact zone where some infiltration of the country rocks by stock-derived fluids occurred. Beyond 4m no stock-derived U, Th, REE or *Pb are noted. Further, whole rock Rb-Sr and stable O isotopic data indicate conductive cooling as opposed to convective, water-induced cooling. The intruded rocks possess low porosity and permeability; this helped prevent elemental migration during the 10 5 to 10 6 years of stock crystallization. The petrographic and geochemical studies show that the Idaho Springs (or equivalent) metamorphic rocks are well suited for radwaste storage. 1 figure, 1 table

Nd and Sr isotopes and K-Ar ages of the Ulreungdo alkali volcanic rocks in the East Sea, South Korea

Energy Technology Data Exchange (ETDEWEB)

Kim Kyuhan; Jang Sunkyung [Ewha Womans Univ., Seoul (Korea); Tanaka, Tsuyoshi; Nagao, Keisuke

1999-07-01

Temporal geochemical and isotopical variations in the Ulreundgo alkali volcanic rocks provide important constraints on the origin and evolution of the volcanic rocks in relation to backarc basin tectonism. We determined the K-Ar ages, major and trace element contents, and Nd and Sr isotopic rations of the alkali volcanic rocks. The activities of Ulreungdo volcanoes can be divided, on the basis of radiometric ages and field occurrences, into five stages, though their activities range from 1.4 Ma to 0.01 Ma with short volcanic hiatus (ca. 0.05-0.3 Ma). The Nd-Sr isotopic data for Ulreungdo volcanic rocks enable us to conclude that: (1) the source materials of Ulreungdo volcanics are isotopically heterogeneous in composition, which is explained by the mixing of mantle derived magma and continental crustal source rocks. There is no systematic isotopic variations with eruption stages. Particularly, some volcanic rocks of stage 2 and 3 have extremely wide initial {sup 87}Sr/{sup 86}Sr isotopic variations ranging from 0.7038 to 0.7092, which are influenced by seawater alterations; (2) the Ulreungdo volcanic rocks show EMI characteristic, while volcanic rocks from the Jejudo, Yeong-il and Jeon-gok areas have slightly depleted mantle source characteristics; (3) the trachyandesite of the latest eruption stage was originated from the mantle source materials which differ from other stages. A schematic isotopic evolution model for alkali basaltic magma is presented in the Ulreungdo volcanic island of the backarc basin of Japanese island arc system. (author)

Relationship between the rock mass deformation and places of occurrence of seismological events

Energy Technology Data Exchange (ETDEWEB)

Janusz Makowka; Jozef Kabiesz; Lin-ming Ddou [Central Mining Institute, Katowice (Poland)

2009-09-15

Static effort of rock mass very rarely causes of rock burst in Polish coal mines. Rock bursts with source in the seismic tremor within the roof rock layers are prevailing. A seismic tremor is an effect of rupture or sliding in roof layers above the exploited panel in coal seam, sometime in a distance from actual exploitation. Sliding, as a rule occurs in fault zone and tremors in it are expected, but monolithic layer rupture is very hard to predict. In a past few years a practice of analyzing state of deformation in high energy seismic tremors zones has been employed. It let gathering experience thanks to witch determination of dangerous shape of reformatted roof is possible. In the paper some typical forms of roof rocks deformations leading to seismic tremor occurrence will be presented. In general these are various types of multidirectional rock layers bending. Real examples of seismic events and rock bursts in the Czech Republic will be shown. 5 refs., 6 figs.

Theory and technology of rock excavation for civil engineering

CERN Document Server

Zou, Dingxiang

2017-01-01

This book summarizes the technical advances in recent decades and the various theories on rock excavation raised by scholars from different countries, including China and Russia. It not only focuses on rock blasting but also illustrates a number of non-blasting methods, such as mechanical excavation in detail. The book consists of 3 parts: Basic Knowledge, Surface Excavation and Underground Excavation. It presents a variety of technical methods and data from diverse sources in the book, making it a valuable theoretical and practical reference resource for engineers, researchers and postgraduates alike.

Application of NURE data to the study of crystalline rocks in the Wyoming uranium province

International Nuclear Information System (INIS)

Rush, S.M.; Anderson, J.R.; Bennett, J.E.

1983-03-01

The Wyoming uranium province study is a part of the National Uranium Resource Evaluation (NURE) program conducted by Bendix Field Engineering Corporation for the US Department of Energy. The ultimate objective of the entire project is the integration of NURE and other data sources to develop a model for a uranium province centered in Wyoming. This paper presents results of the first phase of the Wyoming uranium province study, which comprises characterization of the crystalline rocks of the study area using NURE hydrogeochemical and stream-sediment data, aerial radiometric and magnetic data, and new data generated for zircons from intrusive rocks in the study area. The results of this study indicate that the stream-sediment, aerial radiometric, aerial magnetic, and zircon data are useful in characterization of the crystalline rocks of the uranium province. The methods used in this project can be applied in two ways toward the recognition of a uranium province: (1) to locate major uranium deposits and occurrences, and (2) to generally identify different crystalline rock types, particularly those that could represent significant uranium source rocks. 14 figures, 8 tables

A Coupled Thermo-Hydro-Mechanical Model of Jointed Hard Rock for Compressed Air Energy Storage

Directory of Open Access Journals (Sweden)

Xiaoying Zhuang

2014-01-01

Full Text Available Renewable energy resources such as wind and solar are intermittent, which causes instability when being connected to utility grid of electricity. Compressed air energy storage (CAES provides an economic and technical viable solution to this problem by utilizing subsurface rock cavern to store the electricity generated by renewable energy in the form of compressed air. Though CAES has been used for over three decades, it is only restricted to salt rock or aquifers for air tightness reason. In this paper, the technical feasibility of utilizing hard rock for CAES is investigated by using a coupled thermo-hydro-mechanical (THM modelling of nonisothermal gas flow. Governing equations are derived from the rules of energy balance, mass balance, and static equilibrium. Cyclic volumetric mass source and heat source models are applied to simulate the gas injection and production. Evaluation is carried out for intact rock and rock with discrete crack, respectively. In both cases, the heat and pressure losses using air mass control and supplementary air injection are compared.

Magnesium Isotopic Evidence for Ancient Subducted Oceanic Crust in LOMU-Like Potassium-Rich Volcanic Rocks

Science.gov (United States)

Sun, Yang; Teng, Fang-Zhen; Ying, Ji-Feng; Su, Ben-Xun; Hu, Yan; Fan, Qi-Cheng; Zhou, Xin-Hua

2017-10-01

To evaluate the role of subducted oceanic crust in the genesis of potassium-rich magmas, we report high-precision Mg isotopic data for a set of Cenozoic volcanic rocks from Northeast China. These rocks overall are lighter in Mg isotopic composition than the normal mantle and display considerable Mg isotopic variations, with δ26Mg ranging from -0.61 to -0.23. The covariation of δ26Mg with TiO2 in these rocks suggests that their light Mg isotopic compositions were derived from recycled oceanic crust in the form of carbonated eclogite in the source region. The strong correlations between δ26Mg and (Gd/Yb)N ratio as well as Sr-Pb isotopes further indicate a multicomponent and multistage origin of these rocks. Magnesium isotopes may thus be used as a novel tracer of recycled oceanic crust in the source region of mantle-derived magmas.

Rock Art

Science.gov (United States)

Henn, Cynthia A.

2004-01-01

There are many interpretations for the symbols that are seen in rock art, but no decoding key has ever been discovered. This article describes one classroom's experiences with a lesson on rock art--making their rock art and developing their own personal symbols. This lesson allowed for creativity, while giving an opportunity for integration…

Geochemical characterization of Parana Basin volcanic rocks: petrogenetic implications

International Nuclear Information System (INIS)

Marques, L.S.

1988-01-01

A detailed study of the geochemical characteristics of Parana Basin volcanic rocks is presented. The results are based on the analyses of major and trace elements of 158 samples. Ninety three of these volcanic samples belong to 8 flow sequences from Rio Grande do Sul and Santa Catarina States. The remaining sixty five samples are distributed over the entire basin. In order to study the influence of crustal contamination processes in changing chemical characteristics of the volcanic rocks, 47 samples representative of the crystalline basement of the southern and southeastern Parana Basin were also analysed. Several petrogenetic models were tested to explain the compocional variability of the volcanic rocks, in particular those of southern region. The results obtained sugest an assimilation-fractional crystallization process as viable to explain the differences of both the chemical characteristics and Sr isotope initial ratios observed in basic and intermediate rocks. A model involving melting processes of basic material, trapped at the base of the crust, with composition similar to low and high TiO 2 basalts appears to be a possibility to originate the Palmas and Chapeco acid melts, respectively. The study of ''uncontaminated'' or poorly contaminated low TiO 2 basic rocks from the southern, central and northern regions shows the existence of significant differences in the geochemical charactetistics according to their geographical occurrence. A similar geochemical diversity is also observed in high TiO 2 basalts and Chapeco volcanics. Differences in incompatible element ratios between low and high TiO 2 ''uncontaminated'' or poorly contaminated basalts suggest that they could have been produced by different degrees of melting in a garnet peridotite source. Geochemical and isotopic (Sr and Nd) data also support the view that basalts from northern and southern regions of Parana Basin originated from mantle source with different composition. (author) [pt

Evolution of consumer information preferences with market maturity in solar PV adoption

Science.gov (United States)

Cale Reeves, D.; Rai, Varun; Margolis, Robert

2017-07-01

Residential adoption of solar photovoltaics (PV) is spreading rapidly, supported by policy initiatives at the federal, state, and local levels. Potential adopters navigate increasingly complex decision-making landscapes in their path to adoption. Much is known about the individual-level drivers of solar PV diffusion that steer adopters through this process, but relatively little is known about the evolution of these drivers as solar PV markets mature. By understanding the evolution of emerging solar PV markets over time, stakeholders in the diffusion of solar PV can increase policy effectiveness and reduce costs. This analysis uses survey data to compare two adjacent markets across a range of relevant characteristics, then models changes in the importance of local vs cosmopolitan information sources by combining theory relating market maturity to adopter behavior with event-history techniques. In younger markets, earlier, innovative adoptions that are tied to a preference for cosmopolitan information sources are more prevalent than expected, suggesting a frustrated demand for solar PV that segues into adoptions fueled by local information preferences contemporary with similar adoptions in older markets. The analysis concludes with policy recommendations to leverage changing consumer information preferences as markets mature.

Effects of CO2 injection and Kerogen Maturation on Low-Field Nuclear Magnetic Resonance Response

Science.gov (United States)

Prasad, M.; Livo, K.

2017-12-01

Low-field Nuclear Magnetic Resonance (NMR) is commonly used in petrophysical analysis of petroleum reservoir rocks. NMR experiments record the relaxation and polarization of in-situ hydrogen protons present in gaseous phases such as free-gas intervals and solution gas fluids, bulk fluid phases such as oil and aquifer intervals, and immovable fractions of kerogen and bitumen. Analysis of NMR relaxation spectra is performed to record how fluid composition, maturity, and viscosity change NMR experimental results. We present T1-T2 maps as thermal maturity of a water-saturated, sub-mature Woodford shale is increased at temperatures from 125 to 400 degrees Celsius. Experiments with applied fluid pressure in paraffinic mineral oil and DI water with varying fluid pH have been performed to mimic reservoir conditions in analysis of the relaxation of bulk fluid phases. We have recorded NMR spectra, T1-T2 maps, and fluid diffusion coefficients using a low-field (2 MHz) MagritekTM NMR. CO2 was injected at a pressure of 900 psi in an in house developed NMR pressure vessel made of torlon plastic. Observable 2D NMR shifts in immature kerogen formations as thermal maturity is increased show generation of lighter oils with increased maturity. CO2 injection leads to a decrease in bulk fluid relaxation time that is attributed to viscosity modification with gas presence. pH variation with increased CO2 presence were shown to not effect NMR spectra. From this, fluid properties have been shown to greatly affect NMR readings and must be taken into account for more accurate NMR reservoir characterization.

Hydrology of some deep mines in Precambrian rocks

International Nuclear Information System (INIS)

Yardley, D.H.

1975-10-01

A number of underground mines were investigated during the summer of 1975. All of them are in Precambrian rocks of the Lake Superior region. They represent a variety of geologic settings. The purpose of the investigations was to make a preliminary study of the dryness, or lack of dryness of these rocks at depth. In other words, to see if water was entering the deeper workings through the unmined rock by some means such as fracture or fault zones, joints or permeable zones. Water entering through old mine workings extending to, or very near to the surface, or from the drilling equipment, was of interest only insofar as it might mask any water whose source was through the hanging or footwall rocks. No evidence of running, seeping or moving water was seen or reported at depths exceeding 3,000 feet. At depths of 3,000 feet or less, water seepages do occur in some of the mines, usually in minor quantities but increased amounts occur as depth becomes less. Others are dry at 2,000 feet of depth. Rock movements associated with extensive mining should increase the local secondary permeability of the rocks adjoining the mined out zones. Also most ore bodies are located where there has been a more than average amount of faulting, fracturing, and folding during the geologic past. They tend to cluster along crustal flows. In general, Precambrian rocks of similar geology, to those seen, well away from zones that have been disturbed by extensive deep mining, and well away from the zones of more intense geologic activity ought to be even less permeable than their equivalents in a mining district

Hydrology of some deep mines in Precambrian rocks

Energy Technology Data Exchange (ETDEWEB)

Yardley, D.H.

1975-10-01

A number of underground mines were investigated during the summer of 1975. All of them are in Precambrian rocks of the Lake Superior region. They represent a variety of geologic settings. The purpose of the investigations was to make a preliminary study of the dryness, or lack of dryness of these rocks at depth. In other words, to see if water was entering the deeper workings through the unmined rock by some means such as fracture or fault zones, joints or permeable zones. Water entering through old mine workings extending to, or very near to the surface, or from the drilling equipment, was of interest only insofar as it might mask any water whose source was through the hanging or footwall rocks. No evidence of running, seeping or moving water was seen or reported at depths exceeding 3,000 feet. At depths of 3,000 feet or less, water seepages do occur in some of the mines, usually in minor quantities but increased amounts occur as depth becomes less. Others are dry at 2,000 feet of depth. Rock movements associated with extensive mining should increase the local secondary permeability of the rocks adjoining the mined out zones. Also most ore bodies are located where there has been a more than average amount of faulting, fracturing, and folding during the geologic past. They tend to cluster along crustal flows. In general, Precambrian rocks of similar geology, to those seen, well away from zones that have been disturbed by extensive deep mining, and well away from the zones of more intense geologic activity ought to be even less permeable than their equivalents in a mining district.

Geologic characterization of Cuvette Centrale petroleum systems Congo-DRC

Energy Technology Data Exchange (ETDEWEB)

Vicentelli, Maria Gabriela C.; Barbosa, Mauro; Rezende, Nelio G.A.M. [HRT Petroleum, Rio de Janeiro, RJ (Brazil)

2008-07-01

The Cuvette Centrale is an almost unexplored basin, which contains some petroleum system elements that indicate the presence of hydrocarbons. In this sense; this paper presents an exploratory alternative for this intracratonic basin. The interpretation of the limited gravimetric, magnetometric, geochemical and seismic available data allowed the identification of many huge structural features and also some areas with hydrocarbon potential for stratigraphic traps. The presence of several oil and gas seeps widespread around the Busira and Lokoro sub-basins indicate that at least one active petroleum system exist in the basin. Despite only four wells have been drilled in the basin, one of them presented oil shows during drilling. Geological correlations between Brazilian Paleozoic basins and Cuvette Centrale sedimentary sequences permitted to conclude that Cambro-Ordovician and Siluro-Devonian source rocks must be present and active in the Cuvette Centrale basin. The tectono-stratigraphic evolution history of the Cuvette Centrale from Neo proterozoic to Recent times shows extensional and compressional/transpressional alternating phases along the geological time. The most confident petroleum system expected in the Cuvette Centrale is characterized by the Cambrian Mamungi shale - source rock - and the Cambro-Ordovician. Upper Arenaceous Sequence - reservoirs, as observed in the MBandaka and Gilson wells and confirmed by surface geology in outcrops. Besides, other potential petroleum systems are expected to occur in the basin. One is characterized by the Neo proterozoic Itury Group source rock and reservoirs in the mature/over mature stage, the others are the Siluro-Devonian and Cretaceous source rocks and reservoirs, expected to occur with better maturity conditions only in the deeper parts of the basin. (author)

Radioactive safety analysis and assessment of waste rock pile site in uranium tailings

International Nuclear Information System (INIS)

Liu Changrong; Liu Zehua; Wang Zhiyong; Zhou Xinghuo

2007-01-01

Based on theoretical calculation and in-situ test results, distribution and emissions of radioactive nuclides of uranium tailings impoundment and waste rock pile sites are analyzed in this paper. It is pointed out that 222 Rn is the main nuclide of uranium tailings impoundment and waste rock pile site. Also 222 Rn is the main source term of public dose. 222 Rn concentrations in the atmospheric environment around and individual dose to Rn gradually decrease with increasing distances to uranium tailings impoundment and waste rock pile site. Based on in-situ tests on five uranium tailings impoundment and waste rock pile sites, a decisive method and safety protection distance are presented, which can be used to guide the validation and design of radioactive safety protection in uranium tailings impoundment and waste rock pile sites. (authors)

Evaluation of abundant hydrocarbon-generation depressions in the deepwater area of Qiongdongnan Basin, South China Sea

Institute of Scientific and Technical Information of China (English)

LIU Zhen; SUN Zhipeng; WANG Zisong; ZHANG Wei; LI Tingan; HE Weijun; LI Fengxia

2016-01-01

It has been confirmed that the key source rocks of Qiongdongnan Basin are associated with the Yacheng Formation, which was deposited in a transitional marine-continental environment. Because the distribution and evolution patterns of the source rocks in the major depressions are different, it is important to determine the most abundant hydrocarbon-generation depressions in terms of exploration effectiveness. Based on an analysis of organic matter characteristics of the source rocks, in combination with drilling data and seismic data, this paper establishes a model to evaluate the hydrocarbon-generation depressions in the deepwater area of Qiongdongnan Basin. First of all, by using the method of seismic-facies model analysis, the distribution of sedimentary facies was determined. Then, the sedimentary facies were correlated with the organic facies, and the distribution of organic facies was predicted. Meanwhile, the thickness of source rocks for all the depressions was calculated on the basis of a quantitative analysis of seismic velocity and lithology. The relationship between mudstone porosity and vitrinite reflectance (Ro) was used to predict the maturity of source rocks. Second, using the parameters such as thickness and maturity of source rocks, the quantity and intensity of gas generation for Yacheng and Lingshui Formations were calculated. Finally, in combination with the identified hydrocarbon resources, the quantity and intensity of gas generation were used as a guide to establish an evaluation standard for hydrocarbon-generation depressions, which was optimized for the main depressions in the Central Depression Belt. It is proposed that Lingshui, Ledong, Baodao and Changchang Depressions are the most abundant hydrocarbon depressions, whilst Songnan and Beijiao Depressions are rich hydrocarbon depressions. Such an evaluation procedure is beneficial to the next stage of exploration in the deep-water area of Qiongdongnan Basin.

Creativity, Spirituality, and Transcendence: Paths to Integrity and Wisdom in the Mature Self. Publications in Creativity Research.

Science.gov (United States)

Miller, Melvin E., Ed.; Cook-Greuter, Susanne R., Ed.

This book contains 11 papers on creativity, spirituality, and transcendence as paths to integrity and wisdom in the mature self. The book begins with the paper "Introduction--Creativity in Adulthood: Personal Maturity and Openness to Extraordinary Sources of Inspiration" (Susanne R. Cook-Greuter, Melvin E. Miller). The next four papers,…

Thermally induced rock stress increment and rock reinforcement response

International Nuclear Information System (INIS)

Hakala, M.; Stroem, J.; Nujiten, G.; Uotinen, L.; Siren, T.; Suikkanen, J.

2014-07-01

This report describes a detailed study of the effect of thermal heating by the spent nuclear fuel containers on the in situ rock stress, any potential rock failure, and associated rock reinforcement strategies for the Olkiluoto underground repository. The modelling approach and input data are presented together repository layout diagrams. The numerical codes used to establish the effects of heating on the in situ stress field are outlined, together with the rock mass parameters, in situ stress values, radiogenic temperatures and reinforcement structures. This is followed by a study of the temperature and stress evolution during the repository's operational period and the effect of the heating on the reinforcement structures. It is found that, during excavation, the maximum principal stress is concentrated at the transition areas where the profile changes and that, due to the heating from the deposition of spent nuclear fuel, the maximum principal stress rises significantly in the tunnel arch area of NW/SW oriented central tunnels. However, it is predicted that the rock's crack damage (CD, short term strength) value of 99 MPa will not be exceeded anywhere within the model. Loads onto the reinforcement structures will come from damaged and loosened rock which is assumed in the modelling as a free rock wedge - but this is very much a worst case scenario because there is no guarantee that rock cracking would form a free rock block. The structural capacity of the reinforcement structures is described and it is predicted that the current quantity of the rock reinforcement is strong enough to provide a stable tunnel opening during the peak of the long term stress state, with damage predicted on the sprayed concrete liner. However, the long term stability and safety can be improved through the implementation of the principles of the Observational Method. The effect of ventilation is also considered and an additional study of the radiogenic heating effect on the brittle

Thermally induced rock stress increment and rock reinforcement response

Energy Technology Data Exchange (ETDEWEB)

Hakala, M. [KMS Hakala Oy, Nokia (Finland); Stroem, J.; Nujiten, G.; Uotinen, L. [Rockplan, Helsinki (Finland); Siren, T.; Suikkanen, J.

2014-07-15

This report describes a detailed study of the effect of thermal heating by the spent nuclear fuel containers on the in situ rock stress, any potential rock failure, and associated rock reinforcement strategies for the Olkiluoto underground repository. The modelling approach and input data are presented together repository layout diagrams. The numerical codes used to establish the effects of heating on the in situ stress field are outlined, together with the rock mass parameters, in situ stress values, radiogenic temperatures and reinforcement structures. This is followed by a study of the temperature and stress evolution during the repository's operational period and the effect of the heating on the reinforcement structures. It is found that, during excavation, the maximum principal stress is concentrated at the transition areas where the profile changes and that, due to the heating from the deposition of spent nuclear fuel, the maximum principal stress rises significantly in the tunnel arch area of NW/SW oriented central tunnels. However, it is predicted that the rock's crack damage (CD, short term strength) value of 99 MPa will not be exceeded anywhere within the model. Loads onto the reinforcement structures will come from damaged and loosened rock which is assumed in the modelling as a free rock wedge - but this is very much a worst case scenario because there is no guarantee that rock cracking would form a free rock block. The structural capacity of the reinforcement structures is described and it is predicted that the current quantity of the rock reinforcement is strong enough to provide a stable tunnel opening during the peak of the long term stress state, with damage predicted on the sprayed concrete liner. However, the long term stability and safety can be improved through the implementation of the principles of the Observational Method. The effect of ventilation is also considered and an additional study of the radiogenic heating effect on the

Influence of the rock heterogeneity on the results of gamma-gamma logging

International Nuclear Information System (INIS)

Umiastowski, K.; Buniak, M.

1977-01-01

The influence of the grain size of granular rock and that of the empty holes size of porous rock on the results of gamma-gamma measurements was investigated. Monte-Carlo calculations and experiments were performed to establish this influence. For the grain (or empty holes) size greater than about 10mm the significant influence on the results of density measurements was found if a 137 Cs source was used. This effect is greater for the dry rock than for the water-saturated one. Formulae enabling the correct density value to be found, if the grain size is known, were proposed. (author)

Comparison of disposal concepts for rock salt and hard rock

International Nuclear Information System (INIS)

Papp, R.

1998-01-01

The study was carried out in the period 1994-1996. The goals were to prepare a draft on spent fuel disposal in hard rock and additionally a comparison with existing disposal concepts for rock salt. A cask for direct disposal of spent fuel and a repository for hard rock including a safeguards concept were conceptually designed. The results of the study confirm, that the early German decision to employ rock salt was reasonable. (orig.)

Mechanism of Rock Burst Occurrence in Specially Thick Coal Seam with Rock Parting

Science.gov (United States)

Wang, Jian-chao; Jiang, Fu-xing; Meng, Xiang-jun; Wang, Xu-you; Zhu, Si-tao; Feng, Yu

2016-05-01

Specially thick coal seam with complex construction, such as rock parting and alternative soft and hard coal, is called specially thick coal seam with rock parting (STCSRP), which easily leads to rock burst during mining. Based on the stress distribution of rock parting zone, this study investigated the mechanism, engineering discriminant conditions, prevention methods, and risk evaluation method of rock burst occurrence in STCSRP through setting up a mechanical model. The main conclusions of this study are as follows. (1) When the mining face moves closer to the rock parting zone, the original non-uniform stress of the rock parting zone and the advancing stress of the mining face are combined to intensify gradually the shearing action of coal near the mining face. When the shearing action reaches a certain degree, rock burst easily occurs near the mining face. (2) Rock burst occurrence in STCSRP is positively associated with mining depth, advancing stress concentration factor of the mining face, thickness of rock parting, bursting liability of coal, thickness ratio of rock parting to coal seam, and difference of elastic modulus between rock parting and coal, whereas negatively associated with shear strength. (3) Technologies of large-diameter drilling, coal seam water injection, and deep hole blasting can reduce advancing stress concentration factor, thickness of rock parting, and difference of elastic modulus between rock parting and coal to lower the risk of rock burst in STCSRP. (4) The research result was applied to evaluate and control the risk of rock burst occurrence in STCSRP.

Draft Genome Sequences of the Black Rock Fungus Knufia petricola and Its Spontaneous Nonmelanized Mutant

OpenAIRE

Tesei, Donatella; Tafer, Hakim; Poyntner, Caroline; Piñar, Guadalupe; Lopandic, Ksenija; Sterflinger, Katja

2017-01-01

ABSTRACT The fungal genus Knufia mostly comprises extremotolerant species from environmental sources, especially rock surfaces. The draft genome sequence of the rock fungus Knufia petricola presented here is the first whole-genome sequence of the only species among black fungi known to have a nonmelanized spontaneous mutant.

Juvenile helium in ancient rocks: II. U-He,K-Ar, Sm-Nd, and Rb-Sr systematics in the Monche Pluton. 3He/4He ratios frozen in uranium-free ultramafic rocks

International Nuclear Information System (INIS)

Tolstikhin, I.N.; Dokuchaeva, V.S.; Kamensky, I.L.; Amelin, Yu.V.

1992-01-01

The important geodynamic parameter, the 3 He/ 4 He ratio in rocks and fluids of the continental crust, is generally decreasing from the mantle values (≅ 10 -5 ) to the radiogenic ratio (≅ 10 -8 ) on the time scale of about 1 Ga or less. However, the ratios, observed in some ancient rocks and minerals, are much higher than the radiogenic value due to a preferential retention of trapped He, when compared with radiogenic helium and/or a low U/ 3 He ratio in a sample. The distribution of He, Ar, Nd, and Sr isotopes, K, Rb, Sm, and U in ultrabasic rocks, in rock-forming minerals, in ores from the 2.49 Ga Monche Pluton, and in basic rocks of the Main Range (the Kola Peninsula) enables one to distinguish sources of the rocks and trapped fluids and outline some peculiarities of petrogenetic and fluid processes. The initial values of var-epsilon Nd (T) = -0.9 ± 0.5 , 87 Sr/ 86 Sr(T) = 0.7021 ± 0.0002, for the 2.49 Ga Monche Pluton are rather similar to these for other layered intrusions of the Baltic Shield. They differ considerably from the model values for the depleted 2.5 Ga old mantle. The observed and rather different sources of 3 He and 4 He as well as the considerable constancy of their ratio in different minerals, separated from both the ultramafic rocks and gabbros, implies: (1) an intensive process of mixing between mantle and crustal components: a melt convection in the chamber may have occurred; (2) the two types of rocks could originate by crystallization differentiation of one and the same melt. Practically all 3 He and 4 He are concentrated in secondary amphiboles; hence the fluid which stimulated the metamorphic process was probably released from the ultramafite-bearing melt

Rollerjaw Rock Crusher

Science.gov (United States)

Peters, Gregory; Brown, Kyle; Fuerstenau, Stephen

2009-01-01

The rollerjaw rock crusher melds the concepts of jaw crushing and roll crushing long employed in the mining and rock-crushing industries. Rollerjaw rock crushers have been proposed for inclusion in geological exploration missions on Mars, where they would be used to pulverize rock samples into powders in the tens of micrometer particle size range required for analysis by scientific instruments.

Range sections as rock models for intensity rock scene segmentation

CSIR Research Space (South Africa)

Mkwelo, S

2007-11-01

Full Text Available This paper presents another approach to segmenting a scene of rocks on a conveyor belt for the purposes of measuring rock size. Rock size estimation instruments are used to monitor, optimize and control milling and crushing in the mining industry...

Dispersion of uranium in accessory apatite in crystalline rocks and its possible petrogenetic meaning

International Nuclear Information System (INIS)

Kral, J.; Burchart, J.

1983-01-01

The coefficient of variation for grain-by-grain fission track uranium analysis of apatites from igneous rocks seems to reflect the temperature of crystallization and the cooling rate. For metamorphic rocks the coefficient represents a complex record of the homogeneity of the source and of metamorphic neocrystallization. As a test case 41 West Carpathian rocks have been examined and the coefficients of variation for U in apatites found to be: granitic rocks 0.30-0.79, paragneisses 0.35-0.95, migmatites 0.55-0.87, and volcanic rocks 0.30-0.40. Most of the frequency distributions are lognormal, though for some cases a normal distribution gives a better fit, and some are incompatible with either of the two distributions. (orig.)

Transient diffusion from a waste solid into fractured porous rock

International Nuclear Information System (INIS)

Ahn, J.; Chambre, P.L.; Pigford, T.H.

1988-01-01

Previous analytical studies of the advective transport of dissolved contaminants through fractured rock have emphasized the effect of molecular diffusion in the rock matrix in affecting the space-time-dependent concentration of the contaminant as it moves along the fracture. Matrix diffusion only in the direction normal to the fracture surface was assumed. Contaminant sources were constant-concentration surfaces of width equal to the fracture aperture and of finite or infinite extent in the transverse direction. Such studies illustrate the far-field transport features of fractured media. To predict the time-dependent mass transfer from a long waste cylinder surrounded by porous rock and intersected by a fracture, the present study includes diffusion from the waste surface directly into porous rock, as well as the more realistic geometry. Here the authors present numerical results from Chambre's analytical solution for the time-dependent mass transfer from the cylinder for the low-flow conditions wherein near-field mass transfer is expected to be controlled by molecular diffusion

Iconography in Bradshaw rock art: breaking the circularity.

Science.gov (United States)

Pettigrew, Jack

2011-09-01

Interpreting the symbols found in the rock art of an extinct culture is hampered by the fact that such symbols are culturally determined. How does one break the circularity inherent in the fact that the knowledge of both the symbols and the culture comes from the same source? In this study, the circularity is broken for the Bradshaw rock art of the Kimberley by seeking anchors from outside the culture. Bradshaw rock art in the Kimberley region of Australia and Sandawe rock art in the Kolo region of Eastern Tanzania were surveyed in six visits on foot, by vehicle, by helicopter and from published or shared images, as well as from the published and online images of Khoisan rock art. Uniquely shared images between Bradshaw and Sandawe art, such as the 'mushroom head' symbol of psilocybin use, link the two cultures and indicate that they were shamanistic. Therefore, many mysterious features in the art can be understood in terms of trance visualisations. A number of other features uniquely link Bradshaw and Sandawe cultures, such as a special affinity for small mammals. There are also many references to baobabs in early Bradshaw art but not later. This can be explained in the context of the Toba super-volcano, the likely human transport of baobabs to the Kimberley and the extraordinary utility of the baobab. Many more mysterious symbols in Bradshaw rock art might await interpretation using the approaches adopted here. © 2011 The Author. Clinical and Experimental Optometry © 2011 Optometrists Association Australia.

The ammonium content in the Malayer igneous and metamorphic rocks (Sanandaj-Sirjan Zone, Western Iran)

Science.gov (United States)

Ahadnejad, Vahid; Hirt, Ann Marie; Valizadeh, Mohammad-Vali; Bokani, Saeed Jabbari

2011-04-01

The ammonium (NH4+) contents of the Malayer area (Western Iran) have been determined by using the colorimetric method on 26 samples from igneous and metamorphic rocks. This is the first analysis of the ammonium contents of Iranian metamorphic and igneous rocks. The average ammonium content of metamorphic rocks decreases from low-grade to high-grade metamorphic rocks (in ppm): slate 580, phyllite 515, andalusite schist 242. In the case of igneous rocks, it decreases from felsic to mafic igneous types (in ppm): granites 39, monzonite 20, diorite 17, gabbro 10. Altered granitic rocks show enrichment in NH4+ (mean 61 ppm). The high concentration of ammonium in Malayer granites may indicate metasedimentary rocks as protoliths rather than meta-igneous rocks. These granitic rocks (S-types) have high K-bearing rock-forming minerals such as biotite, muscovite and K-feldspar which their potassium could substitute with ammonium. In addition, the high ammonium content of metasediments is probably due to inheritance of nitrogen from organic matter in the original sediments. The hydrothermally altered samples of granitic rocks show highly enrichment of ammonium suggesting external sources which intruded additional content by either interaction with metasedimentary country rocks or meteoritic solutions.

Podosomes, But Not the Maturation Status, Determine the Protease-Dependent 3D Migration in Human Dendritic Cells.

Science.gov (United States)

Cougoule, Céline; Lastrucci, Claire; Guiet, Romain; Mascarau, Rémi; Meunier, Etienne; Lugo-Villarino, Geanncarlo; Neyrolles, Olivier; Poincloux, Renaud; Maridonneau-Parini, Isabelle

2018-01-01

Dendritic cells (DC) are professional Antigen-Presenting Cells scattered throughout antigen-exposed tissues and draining lymph nodes, and survey the body for pathogens. Their ability to migrate through tissues, a 3D environment, is essential for an effective immune response. Upon infection, recognition of Pathogen-Associated Molecular Patterns (PAMP) by Toll-like receptors (TLR) triggers DC maturation. Mature DC (mDC) essentially use the protease-independent, ROCK-dependent amoeboid mode in vivo , or in collagen matrices in vitro . However, the mechanisms of 3D migration used by human immature DC (iDC) are still poorly characterized. Here, we reveal that human monocyte-derived DC are able to use two migration modes in 3D. In porous matrices of fibrillar collagen I, iDC adopted the amoeboid migration mode. In dense matrices of gelled collagen I or Matrigel, iDC used the protease-dependent, ROCK-independent mesenchymal migration mode. Upon TLR4 activation by LPS, mDC-LPS lose the capacity to form podosomes and degrade the matrix along with impaired mesenchymal migration. TLR2 activation by Pam 3 CSK 4 resulted in DC maturation, podosome maintenance, and efficient mesenchymal migration. Under all these conditions, when DC used the mesenchymal mode in dense matrices, they formed 3D podosomes at the tip of cell protrusions. Using PGE 2 , known to disrupt podosomes in DC, we observed that the cells remained in an immature status and the mesenchymal migration mode was abolished. We also observed that, while CCL5 (attractant of iDC) enhanced both amoeboid and mesenchymal migration of iDC, CCL19 and CCL21 (attractants of mDC) only enhanced mDC-LPS amoeboid migration without triggering mesenchymal migration. Finally, we examined the migration of iDC in tumor cell spheroids, a tissue-like 3D environment. We observed that iDC infiltrated spheroids of tumor cells using both migration modes. Altogether, these results demonstrate that human DC adopt the mesenchymal mode to

Alteration of immature sedimentary rocks on Earth and Mars. Recording Aqueous and Surface-atmosphere Processes

Energy Technology Data Exchange (ETDEWEB)

Cannon, Kenneth M. [Brown Univ., Providence, RI (United States); Mustard, John F. [Brown Univ., Providence, RI (United States); Salvatore, Mark R. [Arizona State Univ., Mesa, AZ (United States)

2015-03-05

The rock alteration and rind formation in analog environments like Antarctica may provide clues to rock alteration and therefore paleoclimates on Mars. Clastic sedimentary rocks derived from basaltic sources have been studied in situ by martian rovers and are likely abundant on the surface of Mars. Moreover, how such rock types undergo alteration when exposed to different environmental conditions is poorly understood compared with alteration of intact basaltic flows. Here we characterize alteration in the chemically immature Carapace Sandstone from Antarctica, a terrestrial analog for martian sedimentary rocks. We employ a variety of measurements similar to those used on previous and current Mars missions. Laboratory techniques included bulk chemistry, powder X-ray diffraction (XRD), hyperspectral imaging and X-ray absorption spectroscopy. Through these methods we find that primary basaltic material in the Carapace Sandstone is pervasively altered to hydrated clay minerals and palagonite as a result of water–rock interaction. A thick orange rind is forming in current Antarctic conditions, superimposing this previous aqueous alteration signature. The rind exhibits a higher reflectance at visible-near infrared wavelengths than the rock interior, with an enhanced ferric absorption edge likely due to an increase in Fe³⁺ of existing phases or the formation of minor iron (oxy)hydroxides. This alteration sequence in the Carapace Sandstone results from decreased water–rock interaction over time, and weathering in a cold, dry environment, mimicking a similar transition early in martian history. This transition may be recorded in sedimentary rocks on Mars through a similar superimposition mechanism, capturing past climate changes at the hand sample scale. These results also suggest that basalt-derived sediments could have sourced significant volumes of hydrated minerals on early Mars due to their greater permeability compared with intact igneous rocks.

Critical Velocity for Shear Localization in A Mature Mylonitic Rock Analogue

Science.gov (United States)

Takahashi, M.; van den Ende, M.; Niemeijer, A. R.; Spiers, C. J.

2016-12-01

Highly localized slip zones, seen within ductile shear zones developed in nature, such as pseudotachylite bands occurring within mylonites, are widely recognized as evidence for earthquake nucleation and/or propagation within and overprinting the ductile regime. To understand brittle/frictional localization processes in ductile shear zones and to connect these to earthquake nucleation and propagation processes, we performed large velocity step-change tests on a brine-saturated, 80:20 (wt. %) halite and muscovite gouge mixture, after forming a mature mylonitic structure through pressure solution creep at low-velocity. The sharp increase in sliding strength that occurs in response to an instantaneous upward velocity-step (direct effect) is an important parameter in determining the potential for and nature of seismic rupture nucleation. We obtained reproducible results regarding low velocity mechanical behavior compared with previous work of Niemeijer and Spiers, [2006], but also obtained new insights into the effects of sudden increases in slip velocity on localization and strength evolution, at velocities above a specific critical velocity Vc ( 20 μm/sec). We found that once a ductile, mylonitic structure has developed in a shear zone, subsequent cataclastic deformation at high velocity (> Vc) is consistently localized in a narrow zone characterized by fine grains of halite aligned in arrays between foliated muscovite Due to this intense localization, structures presumably developed under low velocity conditions were still preserved in large parts of the gouge body. This switch to localized deformation is controlled by the imposed velocity, and becomes most apparent at velocities over Vc. In addition, the direct effect a decreases rapidly when the velocity exceeds Vc. This implies that slip can localize and accelerate towards seismic velocities more or less instantly once Vc is exceeded. Obtaining a measure for Vc in natural faults is therefore of key importance

Neutron activation analysis of alternative phosphate rocks used in animal nutrition

International Nuclear Information System (INIS)

Canella, Artur A.; Ferreira, Walter M.

2005-01-01

Since 1980's, Bovine Sponghiform Encephalophaty has insidiously created a fierce battleground between farmers, scientists, environmentalists and consumers. The use of meat and bone meals is currently prohibited in ruminant feeds throughout the world. Some inorganic sources offer the combination of high phosphorus content and acceptable animal digestibility make them options as supplemental phosphorus, for instance phosphate rocks, general term applied to minerals valued chiefly for their phosphorus content. However, phosphate rocks are long been known containing hazardous elements, make them sometimes unsuitable for animal nutrition. Neutron Activation Analysis has been supportive to the mineral evaluation of alternative phosphate rocks. This evaluation is subject of on-going doctoral thesis which has been carried-out by the main author. The NAA method has been very efficient due to its highly sensitive and multi-elemental nature. In this paper results of Vanadium content from three different phosphate rocks are presented. Their values have been pointed out that Brazilian phosphate rocks present hazardous elements at the same levels of phosphate rocks from some countries of Africa, North America and Middle East, data from our study (Brazilian data) and FAO - Food and Agriculture Organization (others countries). (author)

Correlation of Improved Version of Cervical Vertebral Maturation Indicator with Other Growth Maturity Indicators

Directory of Open Access Journals (Sweden)

Tripti Tikku

2013-01-01

Conclusion: The correlation between middle phalanx of 3rd finger (MP3 and cervical vertebral maturation method (CVMI and CVMS was higher as compared to the correlation of either of the cervical vertebral maturation method or MP3 with dental maturation indicator.

Nitrogen in rock: Occurrences and biogeochemical implications

Science.gov (United States)

Holloway, J.M.; Dahlgren, R.A.

2002-01-01

There is a growing interest in the role of bedrock in global nitrogen cycling and potential for increased ecosystem sensitivity to human impacts in terrains with elevated background nitrogen concentrations. Nitrogen-bearing rocks are globally distributed and comprise a potentially large pool of nitrogen in nutrient cycling that is frequently neglected because of a lack of routine analytical methods for quantification. Nitrogen in rock originates as organically bound nitrogen associated with sediment, or in thermal waters representing a mixture of sedimentary, mantle, and meteoric sources of nitrogen. Rock nitrogen concentrations range from trace levels (>200 mg N kg -1) in granites to ecologically significant concentrations exceeding 1000 mg N kg -1 in some sedimentary and metasedimentary rocks. Nitrate deposits accumulated in arid and semi-arid regions are also a large potential pool. Nitrogen in rock has a potentially significant impact on localized nitrogen cycles. Elevated nitrogen concentrations in water and soil have been attributed to weathering of bedrock nitrogen. In some environments, nitrogen released from bedrock may contribute to nitrogen saturation of terrestrial ecosystems (more nitrogen available than required by biota). Nitrogen saturation results in leaching of nitrate to surface and groundwaters, and, where soils are formed from ammonium-rich bedrock, the oxidation of ammonium to nitrate may result in soil acidification, inhibiting revegetation in certain ecosystems. Collectively, studies presented in this article reveal that geologic nitrogen may be a large and reactive pool with potential for amplification of human impacts on nitrogen cycling in terrestrial and aquatic ecosystems.

Developing maturity grids for assessing organisational capabilities

DEFF Research Database (Denmark)

Maier, Anja; Moultrie, James; Clarkson, P John

2009-01-01

Keyword: Maturity Model,Maturity Grid,Maturity Matrix,Organisational Capabilities,Benchmarking,New Product Development,Perfirmance Assessment......Keyword: Maturity Model,Maturity Grid,Maturity Matrix,Organisational Capabilities,Benchmarking,New Product Development,Perfirmance Assessment...

Hydrocarbon Reservoir Identification in Volcanic Zone by using Magnetotelluric and Geochemistry Information

Science.gov (United States)

Firda, S. I.; Permadi, A. N.; Supriyanto; Suwardi, B. N.

2018-03-01

The resistivity of Magnetotelluric (MT) data show the resistivity mapping in the volcanic reservoir zone and the geochemistry information for confirm the reservoir and source rock formation. In this research, we used 132 data points divided with two line at exploration area. We used several steps to make the resistivity mapping. There are time series correction, crosspower correction, then inversion of Magnetotelluric (MT) data. Line-2 and line-3 show anomaly geological condition with Gabon fault. The geology structure from the resistivity mapping show the fault and the geological formation with the geological rock data mapping distribution. The geochemistry information show the maturity of source rock formation. According to core sample analysis information, we get the visual porosity for reservoir rock formation in several geological structure. Based on that, we make the geological modelling where the potential reservoir and the source rock around our interest area.

Pyroclastic rocks: another manifestation of ultramafic volcanism on Gorgona Island, Colombia

Science.gov (United States)

Echeverría, Lina M.; Aitken, Bruce G.

1986-04-01

Tertiary ultramafic volcanism on Gorgona Island, Colombia, is manifested not only by komatiite flows, but also by a more voluminous sequence of tuff breccias, which is cut by comagmatic picrite dikes. The ultramafic pyroclastic rocks are chaotic to stratified mixtures of angular to subrounded glassy picritic blocks and a fine grained volcaniclastic matrix that consists primarily of plastically-deformed, glassy globules. The entire deposit is interpreted to have formed by an explosive submarine eruption of phenocryst-laden picritic magma. MgO contents of tuff breccias and picrite dikes range from 21 to 27 wt%. Relative to nearby komatiite flows, these rocks are MgO-rich, and FeO-, TiO2- and Ni-poor. HREE concentrations are very low (source region. Nd isotopic data suggest a cogenetic relationship between the picritic magma that formed the tuff breccia and associated dikes and that which produced the komatiite flows. Nevertheless Pb isotopic data as well as whole rock geochemistry preclude such a connection, either due to olivine fractionation/accumulation or to different degrees of partial melting. These ultramafic rock types crystallized from magmas which most likely were extracted from distinct mantle source regions.

Fluid and rock interaction in permeable volcanic rock

International Nuclear Information System (INIS)

Lindley, J.I.

1985-01-01

Four types of interrelated changes -geochemical, mineralogic, isotopic, and physical - occur in Oligocene volcanic units of the Mogollon-Datil volcanic field, New Mexico. These changes resulted from the operation of a geothermal system that, through fluid-rock interaction, affected 5 rhyolite ash-flow tuffs and an intercalated basaltic andesite lava flow causing a potassium metasomatism type of alteration. (1) Previous studies have shown enrichment of rocks in K 2 O as much as 130% of their original values at the expense of Na 2 O and CaO with an accompanying increase in Rb and decreases in MgO and Sr. (2) X-ray diffraction results of this study show that phenocrystic plagioclase and groundmass feldspar have been replaced with pure potassium feldspar and quartz in altered rock. Phenocrystic potassium feldspar, biotite, and quartz are unaffected. Pyroxene in basaltic andesite is replaced by iron oxide. (3) delta 18 O increases for rhyolitic units from values of 8-10 permil, typical of unaltered rock, to 13-15 permil, typical of altered rock. Basaltic andesite, however, shows opposite behavior with a delta 18 of 9 permil in unaltered rock and 6 permit in altered. (4) Alteration results in a density decrease. SEM revealed that replacement of plagioclase by fine-grained quartz and potassium feldspar is not a volume for volume replacement. Secondary porosity is created in the volcanics by the chaotic arrangement of secondary crystals

People Capability Maturity Model. SM.

Science.gov (United States)

1995-09-01

tailored so it consumes less time and resources than a traditional software process assessment or CMU/SEI-95-MM-02 People Capability Maturity Model...improved reputation or customer loyalty. CMU/SEI-95-MM-02 People Capability Maturity Model ■ L5-17 Coaching Level 5: Optimizing Activity 1...Maturity Model CMU/SEI-95-MM-62 Carnegie-Mellon University Software Engineering Institute DTIC ELECTE OCT 2 7 1995 People Capability Maturity

On the Rock Partridge in the painting “Saint Jerome in the study” by Antonello da Messina.

Directory of Open Access Journals (Sweden)

Tommaso La Mantia

2012-05-01

Full Text Available Pictorial work of Antonello da Messina during the Sicilian period (1455-60 is considered less fruitful and less mature than during his stay in Venice (ca 1474-1476. While some art critics consider the painting “Saint Jerome in the study” a work of the first period, others believe that it was produced during the Venice period. The Authors analysed the plumage characters of the Rock Partridge, Alectoris graeca, depicted with symbolic significance in the painting, to try the identification of the population which the subject used as model could belong to. However, they conclude that the identification as a Sicilian as well as an Alpine Rock Partridge is doubtful and in this case the plumage of the bird depicted does not help to resolve the controversy of painting dating.

Infilling Littleton Street Mine, Wallsall, with colliery spoil rock paste

Energy Technology Data Exchange (ETDEWEB)

Jarvis, S.T.; Braithwaite, P.A. [Ove Arup and Partners, Birmingham (United Kingdom)

1993-12-31

Describes the filling of an abandoned underground mine with low strength (12-20 kPa) paste made of coal mining waste. With a volume of 550,000 m{sup 3}, it was the largest mine to be filled with rock paste to date. The abandoned mine, flooded with underground water, consists of room and pillar workings at shallow depth of 35 to 60 m. Height of the underground mine cavity varies between 4 and 8 m. The process of infilling and tests and systems for monitoring infilling completeness and strength are described. Benefits of rock paste over other forms of infilling are discussed. Land reclamation work at the source sites is also described. Mineral waste source sites and specifications of the materials are given. After work completion, about 18 ha of derelict urban land were released for redevelopment. 6 refs.

Natural sources of ionizing radiations

International Nuclear Information System (INIS)

Marej, A.N.

1984-01-01

Natural sources of ionizing radiations are described in detail. The sources are subdivided into sources of extraterrestrial origin (cosmic radiation) and sources of terrestrial origin. Data on the concentration of different nuclides in rocks, various soils, ground waters, atmospheric air, tissues of plants and animals, various food stuffs are presented. The content of natural radionuclides in environmental objects, related to human activities, is discussed

Burial history influence on the generation of some Italian oils

Energy Technology Data Exchange (ETDEWEB)

Mattavelli, L.; Novelli, L. (AGIP SPA, San Donato Milanese (Italy))

1990-05-01

Many Italian oils were sourced by Triassic source rock; evidence of this exists in the Po Plain. In the Adriatic Sea, and offshore southern Sicily. Bulk and geochemical characteristics of these oils are quite dissimilar: heavy oils as well as gasolines were discovered. Such differences are partly attributable to the organic matter type and to environmental conditions, but the role of the source rock's burial histories is fundamental in determining oil characteristics. The different burial histories in these two areas definitely account for these differences. In the Po Plain, the Raethian Argilliti di Riva di Solto Formation, source rock of condensates of the Malossa area, started to generate very early as a consequence of the noticeable Rhaetian-Liassic subsidence. The generation of oil continued for a long geological time, but probably hydrocarbons were lost for the lack of traps. Only condensates, generated by the further Pliocene-Quaternary burial, were accumulated in the Neogene traps. In the western part of the Po Plain, Gaggiano and Villafortuna oils (34 and 40{degree} API), sourced by the Ladinian Meride Formation, were generated only during the sizeable Neogene-Quaternary subsidence. The high heating rate in this case probably enhanced expulsion efficiency, allowing secondary migration toward shallower depths and, consequently, preventing hydrocarbons from secondary cracking. Offshore in southern Sicily (Gela field), the recent subsidence (Pliocene-Pleistocene) is responsible for Triassic source rock maturation. In this case the shallower depth reached by the source rock and, consequently, the lower temperatures at which maturity occurred are partly responsible for the generation of heavy oils, even if other factors such as early expulsion due to tectonics and organic matter type probably play a more important role.

Strong-motion characteristics and source process during the Suruga Bay earthquake in 2009 through observed records on rock sites

International Nuclear Information System (INIS)

Shiba, Yoshiaki; Sato, Hiroaki; Kuriyama, Masayuki

2010-01-01

On 11 August 2009, a moderate earthquake of M 6.5 occurred in the Suruga Bay region, south of Shizuoka prefecture. During this event, JMA Seismic Intensity reached 6 lower in several cities around the hypocenter, and at Hamaoka nuclear power plant of Chubu Electric Power reactors were automatically shutdown due to large ground motions. Though the epicenter is located at the eastern edge of source area for the assumed great Tokai earthquake of M 8, this event is classified into the intra-plate (intra-slab) earthquake, due to its focal depth lower than that of the plate boundary and fault geometry supposed from the moment tensor solution. Dense strong-motion observation network has been deployed mainly on the rock outcrops by our institute around the source area, and the waveform data of the main shock and several aftershocks were obtained at 13 stations within 100 km from the hypocenter. The observed peak ground motions and velocity response spectral amplitudes are both obviously larger than the empirical attenuation relations derived from the inland and plate-boundary earthquake data, which displays the characteristics of the intra-slab earthquake faulting. Estimated acceleration source spectra of the main shock also exhibit the short period level about 1.7 times larger than the average of those for past events, and it corresponds with the additional term in the attenuation curve of the peak ground acceleration for the intra-plate earthquake. Detailed source process of the main shock is inferred using the inversion technique. The initial source model is assumed to be composed of two distinct fault planes according to the minute aftershock distribution. Estimated source model shows that large slip occurred near the hypocenter and at the boundary region between two fault planes where the rupture transfers from primary to secondary fault. Furthermore the broadband source inversion using velocity motions in the frequency up to 5 Hz demonstrates the high effective

Textural Maturity Analysis and Sedimentary Environment Discrimination Based on Grain Shape Data

Science.gov (United States)

Tunwal, M.; Mulchrone, K. F.; Meere, P. A.

2017-12-01

Morphological analysis of clastic sedimentary grains is an important source of information regarding the processes involved in their formation, transportation and deposition. However, a standardised approach for quantitative grain shape analysis is generally lacking. In this contribution we report on a study where fully automated image analysis techniques were applied to loose sediment samples collected from glacial, aeolian, beach and fluvial environments. A range of shape parameters are evaluated for their usefulness in textural characterisation of populations of grains. The utility of grain shape data in ranking textural maturity of samples within a given sedimentary environment is evaluated. Furthermore, discrimination of sedimentary environment on the basis of grain shape information is explored. The data gathered demonstrates a clear progression in textural maturity in terms of roundness, angularity, irregularity, fractal dimension, convexity, solidity and rectangularity. Textural maturity can be readily categorised using automated grain shape parameter analysis. However, absolute discrimination between different depositional environments on the basis of shape parameters alone is less certain. For example, the aeolian environment is quite distinct whereas fluvial, glacial and beach samples are inherently variable and tend to overlap each other in terms of textural maturity. This is most likely due to a collection of similar processes and sources operating within these environments. This study strongly demonstrates the merit of quantitative population-based shape parameter analysis of texture and indicates that it can play a key role in characterising both loose and consolidated sediments. This project is funded by the Irish Petroleum Infrastructure Programme (www.pip.ie)

First data on Sm-Nd systematization of Khanka Massif metamorphic rocks, Primor'e

International Nuclear Information System (INIS)

Mishkin, M.A.; Khanchuk, A.I.; Zhuravlev, D.Z.; Lavrik, S.N.

2000-01-01

The age of the metamorphic rocks of the Khanka massif, Primor'e, is determined through the method of the Sm-Nd isotopic dating. The results of the isotopic studies on the amphibolites of the Nakhimov suite of the Khanka massif indicated that the rocks of this suite are not older than 1.7 billion years. The obtained age corresponds to the time of the amphibolite protolith formation, the source whereof is the moderately depleted mantle. The isotopic age of the amphibole and plagioclase mineral fractions constitutes 733 ± 25 mln years, which reflects the time of the Nakhimov suite rocks metamorphism [ru

IT Governance Maturity: Developing a Maturity Model Using the Delphi Method

NARCIS (Netherlands)

Smits, Daniël; van Hillegersberg, Jos

2015-01-01

To advance in maturity, organizations should pay attention to both the hard and soft sides of IT governance (ITG). The hard side is related to processes and structure, the soft side to social aspects like behavior and organizational culture. This paper describes a study to develop an ITG maturity

Disc cutter wear and rock texture in hard rock TBM tunneling

International Nuclear Information System (INIS)

Koizumi, Yu; Tsusaka, Kimikazu; Tanimoto, Chikaosa; Nakagawa, Shigeo; Fujita, Naoya

2008-01-01

Disc cutter wear in TBM tunneling is caused by initial fragmentation of a solid rock face (the primary fragmentation) and fragmentation of residual rock pieces between a cutterhead and the face (the secondary fragmentation). In two projects through sedimentary and granitic rocks, the authors investigated the relationships between the rate of cutter wear caused by the primary fragmentation, point load index and the grain size and contents of abrasive minerals. As a result, it was found that the tensile strength and the mineral contents of rocks significantly influenced the cutter wear in both projects and thus it is necessary to take into account of rock type. (author)

Rock 'n' Roll Heroes: Letter to President Eisenhower.

Science.gov (United States)

Mueller, Jean W., Ed.

1985-01-01

This primary source document can be used to teach secondary students about the rock 'n' roll era that emerged in the 1950's. The document is a letter written in 1958 by three teenagers to President Eisenhower concerning the induction of Elvis Presley into the U.S. Army. Class activities are also suggested. (RM)

Rocks Can Wow? Yes, Rocks Can Wow!

Science.gov (United States)

Hardman, Sally; Luke, Sue

2016-01-01

Rocks and fossils appear in the National Curriculum of England science programmes of study for children in year 3 (ages 7-8). A frequently asked question is "How do you make the classification of rocks engaging?" In response to this request from a school, a set of interactive activities was designed and organised by tutors and students…

Determined Initial lead for South Of Isua (SOI) terrain suggests a single homogeneous source for it and possibly other archaean rocks

Science.gov (United States)

Tera, F.

2011-12-01

other rocks from Isua Greenstone Belt (1) and Amîtsoq gneiss (4) fall inside the TULIP triangle of SOI, suggesting potential derivation of these Archaean rocks from the same homogeneous source.

On the maturity of open source BPM systems

NARCIS (Netherlands)

Wohed, P.; Hofstede, ter A.H.M.; Russell, N.C.; Andersson, B.; Aalst, van der W.M.P.

2009-01-01

Introduction: Two major trends in the area of information systems development are (1) the growing interest in Workflow and Business Process Management (BPM) systems and (2) the increasing acceptance and use of open source software. This development raises the following questions: 1. What are the

MatureBayes: a probabilistic algorithm for identifying the mature miRNA within novel precursors.

Directory of Open Access Journals (Sweden)

Katerina Gkirtzou

Full Text Available BACKGROUND: MicroRNAs (miRNAs are small, single stranded RNAs with a key role in post-transcriptional regulation of thousands of genes across numerous species. While several computational methods are currently available for identifying miRNA genes, accurate prediction of the mature miRNA remains a challenge. Existing approaches fall short in predicting the location of mature miRNAs but also in finding the functional strand(s of miRNA precursors. METHODOLOGY/PRINCIPAL FINDINGS: Here, we present a computational tool that incorporates a Naive Bayes classifier to identify mature miRNA candidates based on sequence and secondary structure information of their miRNA precursors. We take into account both positive (true mature miRNAs and negative (same-size non-mature miRNA sequences examples to optimize sensitivity as well as specificity. Our method can accurately predict the start position of experimentally verified mature miRNAs for both human and mouse, achieving a significantly larger (often double performance accuracy compared with two existing methods. Moreover, the method exhibits a very high generalization performance on miRNAs from two other organisms. More importantly, our method provides direct evidence about the features of miRNA precursors which may determine the location of the mature miRNA. We find that the triplet of positions 7, 8 and 9 from the mature miRNA end towards the closest hairpin have the largest discriminatory power, are relatively conserved in terms of sequence composition (mostly contain a Uracil and are located within or in very close proximity to the hairpin loop, suggesting the existence of a possible recognition site for Dicer and associated proteins. CONCLUSIONS: This work describes a novel algorithm for identifying the start position of mature miRNA(s produced by miRNA precursors. Our tool has significantly better (often double performance than two existing approaches and provides new insights about the potential use

Evolution characteristics and application of diamondoids in coal measures

Directory of Open Access Journals (Sweden)

Chenchen Fang

2016-02-01

Full Text Available As diamondoids have been used to evaluate petroleum and source rocks widely; their origin, evolution, and distribution in petroleum as well as source rocks have attracted ever more attention. Having finished the pyrolysis simulation experiment of the coal measure mudrocks from Xujiahe Formation, Sichuan Basin, results indicated that with the equivalent vitrinite reflectance (EasyRo increasing, diamondoids experience generation (1.0%  1.5%. Throughout the simulation experiment, diamondoid parameters MAI, EAI, and TMAI-1 kept good relationships with maturity within the range of EasyRo 1.5%–2.5%, 1.0%–2.5%, and 1.5%–2.5% respectively, with all of the correlation coefficient (R2 being above 0.7844, this indicated that these parameters can be used to evaluate maturity at these ranges. In addition, the yield ratios A/D, MA/MD, DMA/DMD, and As/Ds also kept good relationships with maturity at the range of EasyRo 1.2%–2.5%, with all of the R2 above 0.9236, this indicated that these ratios can be used to evaluate maturity index at this range.

Academic Achievement of High School Students in Relation to Their Anxiety, Emotional Maturity and Social Maturity

Science.gov (United States)

Puar, Surjit Singh

2013-01-01

The present study has been designed to investigate the non-cognitive variables like anxiety, emotional maturity and social maturity and their relationship with academic achievement and also to see the locale-wise differences on the basis of their anxiety, emotional maturity and social maturity. The study was conducted over a sample of 400 (200…

Thermal maturity and burial history modelling of shale is enhanced by use of Arrhenius time-temperature index and memetic optimizer

Directory of Open Access Journals (Sweden)

David A. Wood

2018-03-01

Full Text Available Thermal maturity indices and modelling based on Arrhenius-equation reaction kinetics have played an important role in oil and gas exploration and provided petroleum generation insight for many kerogen-rich source rocks. Debate continues concerning how best to integrate the Arrhenius equation and which activation energies (E and frequency factors (A values to apply. A case is made for the strong theoretical basis and practical advantages of the time-temperature index (∑TTIARR method, first published in 1998, using a single, carefully selected E-A set (E = 218 kJ/mol (52.1 kcal/mol; A = 5.45E+26/my from the well-established A-E trend for published kerogen kinetics. An updated correlation between ∑TTIARR and vitrinite reflectance (Ro is provided in which the ∑TTIARR scale spans some 18 orders of magnitude. The method is readily calculated in spreadsheets and can be further enhanced by visual basic for application code to provide optimization. Optimization is useful for identifying possible geothermal gradients and erosion intervals covering multiple burial intervals that can match calculated thermal maturities with measured Ro data. A memetic optimizer with firefly and dynamic local search memes is described that flexibly conducts exploration and exploitation of the feasible, multi-dimensional, thermal history solution space to find high-performing solutions to complex burial and thermal histories. A complex deep burial history example, with several periods of uplift and erosion and fluctuating heat flow is used to demonstrate what can be achieved with the memetic optimizer. By carefully layering in constraints to the models specific insights to episodes in their thermal history can be exposed, leading to better characterization of the timing of petroleum generation. The objective function found to be most effective for this type of optimization is the mean square error (MSE of multiple burial intervals for the difference between

Leveraging People-Related Maturity Issues for Achieving Higher Maturity and Capability Levels

Science.gov (United States)

Buglione, Luigi

During the past 20 years Maturity Models (MM) become a buzzword in the ICT world. Since the initial Crosby's idea in 1979, plenty of models have been created in the Software & Systems Engineering domains, addressing various perspectives. By analyzing the content of the Process Reference Models (PRM) in many of them, it can be noticed that people-related issues have little weight in the appraisals of the capabilities of organizations while in practice they are considered as significant contributors in traditional process and organizational performance appraisals, as stressed instead in well-known Performance Management models such as MBQA, EFQM and BSC. This paper proposes some ways for leveraging people-related maturity issues merging HR practices from several types of maturity models into the organizational Business Process Model (BPM) in order to achieve higher organizational maturity and capability levels.

Revised models for hydrocarbon generation, migration and accumulation in Jurassic coal measures of the Turpan basin, NW China

Energy Technology Data Exchange (ETDEWEB)

Li Maowen; Stasiuk, L.D. [Geological Survey of Canada, Calgary, Alberta (Canada); Bao Jianping [Jianghan Petroleum University, Hubei (China); Lin, R. [Petroleum University (Beijing), Changping (China); Yuan Mingsheng [PetroChina Tu-Ha Oilfield Company, Xingjiang (China)

2001-07-01

Whether or not the Lower-Middle Jurassic coal measures in the Turpan basin of NW China have generated commercial quantities of liquid petroleums is a problem of considerable importance that remains contentious as it has not yet been resolved unequivocally. This study provides evidence against the Jurassic humic coals as the only major source for the oils discovered in the Taibei depression of this basin and suggests additional significant contributions from the Upper Permian and Middle-Lower Jurassic lacustrine source rocks. The Carboniferous-Permian marine source rocks may have been important also in limited locations along the major basement faults. Molecular and petrographic data indicate that the majority of the Middle Jurassic strata are currently immature or marginally mature with respect to hydrocarbon generation. Within the major depocenters, the Middle-Lower Jurassic coal-bearing strata of the Baodaowan and Xishanyao formations has reached the conventional oil window (i.e. with vitrinite reflectance >0.7 per cent Ro). Pre-Jurassic (Upper Permian in particular) derived hydrocarbons appear to be widespread in extracts of fractured Jurassic coal and fine-grained rocks. Large differences have been observed in the absolute concentrations of biomarker compounds in rock extracts of various source intervals. Thus, 'coaly' biomarker signatures of the oils most likely resulted from mixing and migration contamination when hydrocarbons derived from mature source rocks migrated up through highly fractured coal seams along deep-seated faults. In addition to conventional exploration targets, revised petroleum generation and accumulation models predict that the focus in the Turpan basin should also include deep structures within the Carboniferous-Permian strata and subtle, low magnitude anticlines and stratigraphic traps within thr Triassic-Jurassic sections. (author)

Thermal history of rocks in southern San Joaquin Valley, California: evidence from fission-track analysis

Science.gov (United States)

Naeser, N.D.; Naeser, C.W.; McCulloh, T.H.

1990-01-01

Fission-track analysis has been used to study the thermal and depositional history of the subsurface Tertiary sedimentary rocks on both sides of the active White Wolf reverse fault in the southern San Joaquin Valley. The distinctly different thermal histories of the rocks in the two structural blocks are clearly reflected in the apatite fission-track data, which suggest that rocks in the rapidly subsiding basin northwest of the fault have been near their present temperature for only about 1 m.y. compared with about 10 m.y. for rocks southeast of the fault. These estimates of heating time agree with previous estimates for these rocks. Zircon fission-track data indicate that the Tertiary sediments were derived from parent rocks of more than one age. However, from at least the Eocene to late Miocene or Pliocene, the major sediment source was rocks related to the youngest Sierra Nevada Mesozoic intrusive complexes, which are presently exposed east and south of the southern San Joaquin Valley. -from Authors

Preliminary analysis of the potential for thermally-induced rock fracture around high-level waste containers

International Nuclear Information System (INIS)

Ratigan, J.L.

1976-01-01

The major results are: the development of parametric formulations relating the potential for thermally induced fracturing in the high-level radioactive waste repository concept to the elastic and thermal properties of the site rock and the depth of the excavation, and the recognition of a need to determine the actual ''failure envelope'' for any potential site rock in the laboratory and adjust the parametric relations appropriately. Analysis of five rock types indicated that none would experience elastic/brittle failure due to the thermal stresses induced by the introduction of a 5 kW heat source. However, the rock strengths and elastic properties are laboratory values and not in situ values

Analysis of mercury in rock varnish samples in areas impacted by coal-fired power plants

International Nuclear Information System (INIS)

Nowinski, Piotr; Hodge, Vernon F.; Gerstenberger, Shawn; Cizdziel, James V.

2013-01-01

Rock varnish is a manganese–iron rich coating that forms on rocks, most often in arid climates. To assess its utility as an environmental monitor of mercury contamination, cold vapor atomic absorption spectrometry (CVAAS) was used for analysis. Samples were collected in the fallout patterns of two coal-fired power plants in southern Nevada: the defunct Mohave Power Plant (MPP) and the operating Reid Gardner Power Plant (RGPP). The resultant Hg concentrations in rock varnishes were plotted as a function of the distance from each power plant. The highest concentrations of Hg occurred at locations that suggest the power plants are the main source of pollutants. In addition, past tracer plume studies carried out at MPP show that the highest tracer concentrations coincide with the highest rock varnish Hg concentrations. However, additional samples are required to further demonstrate that power plants are indeed the sources of mercury in varnishes. -- Highlights: •We analyze desert varnish samples collected in the fallout patterns of two coal-fired and analyzed for Hg by CVAA. •The resultant Hg concentrations in the desert varnish samples were plotted as a function of the distance from each power plant. •The highest concentrations of Hg occurred at locations that suggest the power plants are the main source of pollutants. •Data indicate the utility of desert varnish as a passive environmental monitor for Hg atmospheric pollution. -- Cold vapor atomic absorption spectrometry (CVAAS) was used for analysis of mercury in varnished rocks collected in the fallout zones of two coal-fired power plants

Evaluation of the instability problems in rock slopes surrounding historical Safranbolu by kinematic analysis

Directory of Open Access Journals (Sweden)

İnan Keskin

2017-10-01

Full Text Available Safranbolu which has high probability for slope-induced disasters is a very worthwhile settlement for our country and also for the world with its historical and cultural heritage. Finding out potential hazards that may affect the wealth of this world heritage city is very crucial. The historic Safranbolu is surrounded by very steep rock slopes, and occasionally instability occurs in the rock mass that forms these slopes. The rock blocks that are relaesed in various causes and shapes can damage the historic town living spaces by creating a source for the rock fallings and moving down the slope in these very steep slopes. The rock slopes were evaluated by kinematic analysis in order to reduce the mentioned damages and to reveal potential hazards. In the study, characteristics of mass that causes rock fallings are analysed, kinematic controlled instability types are determined considering the obtained data and characteristic of slopes.

Rock Physics

DEFF Research Database (Denmark)

Fabricius, Ida Lykke

2017-01-01

Rock physics is the discipline linking petrophysical properties as derived from borehole data to surface based geophysical exploration data. It can involve interpretation of both elastic wave propagation and electrical conductivity, but in this chapter focus is on elasticity. Rock physics is based...... on continuum mechanics, and the theory of elasticity developed for statics becomes the key to petrophysical interpretation of velocity of elastic waves. In practice, rock physics involves interpretation of well logs including vertical seismic profiling (VSP) and analysis of core samples. The results...

STRAIN LOCALIZATION PECULIARITIES AND DISTRIBUTION OF ACOUSTIC EMISSION SOURCES IN ROCK SAMPLES TESTED BY UNIAXIAL COMPRESSION AND EXPOSED TO ELECTRIC PULSES

Directory of Open Access Journals (Sweden)

V. A. Mubassarova

2014-01-01

Full Text Available Results of uniaxial compression tests of rock samples in electromagnetic fields are presented. The experiments were performed in the Laboratory of Basic Physics of Strength, Institute of Continuous Media Mechanics, Ural Branch of RAS (ICMM. Deformation of samples was studied, and acoustic emission (AE signals were recorded. During the tests, loads varied by stages. Specimens of granite from the Kainda deposit in Kyrgyzstan (similar to samples tested at the Research Station of RAS, hereafter RS RAS were subject to electric pulses at specified levels of compression load. The electric pulses supply was galvanic; two graphite electrodes were fixed at opposite sides of each specimen. The multichannel Amsy-5 Vallen System was used to record AE signals in the six-channel mode, which provided for determination of spatial locations of AE sources. Strain of the specimens was studied with application of original methods of strain computation based on analyses of optical images of deformed specimen surfaces in LaVISION Strain Master System.Acoustic emission experiment data were interpreted on the basis of analyses of the AE activity in time, i.e. the number of AE events per second, and analyses of signals’ energy and AE sources’ locations, i.e. defects.The experiment was conducted at ICMM with the use of the set of equipment with advanced diagnostic capabilities (as compared to earlier experiments described in [Zakupin et al., 2006a, 2006b; Bogomolov et al., 2004]. It can provide new information on properties of acoustic emission and deformation responses of loaded rock specimens to external electric pulses.The research task also included verification of reproducibility of the effect (AE activity when fracturing rates responded to electrical pulses, which was revealed earlier in studies conducted at RS RAS. In terms of the principle of randomization, such verification is methodologically significant as new effects, i.e. physical laws, can be considered

Microstructural variation of vitrified floor tile incorporated with granitic rock waste

International Nuclear Information System (INIS)

Souza, A.J.; Holanda, J.N.F.

2009-01-01

The ornamental rock industry from Northwest Fluminense generates huge amounts of wastes in the form of a fine powder. These wastes are deposited in nature without any care about environmental degradation, which can cause damage to public health, pollution of the natural water sources, and silted banks of rivers. In addition, they also can to affect the landscape aesthetically. In this work was used a granitic rock waste from Santo Antonio de Padua-RJ. This waste is rich in alkaline oxides, which promote the formation of liquid phase and assist the densification of traditional ceramics. The ceramic bodies with up to 47.5% granitic rock waste were pressed at 50 MPa. The ceramic pieces were fired at 1250 deg C. The evolution of sintered microstructure was evaluated by scanning electron microscopy and X-ray diffraction. The results showed that the granitic rock waste influences significantly the microstructure of the sintered ceramic bodies. (author)

The seismic investigation of rock properties at the Carwynnen test mine

International Nuclear Information System (INIS)

New, B.M.

1984-11-01

The research described follows on from the seismic velocity tomography carried out previously at this site and describes an attempt to map the rock mass in terms of its attenuative properties. This is done by comparison of the spectral distributions of energy within wave packets observed at various distances from numerous source locations. The method was not found sensitive to the variations in natural rock condition at this site as the spectra were dominated by the effects of man-made openings and rock damage which appeared to control the energy input/output transfer function at each location. The seismic shadow caused by the presence of a major void in the area was clearly identified and suggested that similar observations could considerably enhance the value of velocity tomography techniques. Shear and compressional wave velocities are used to obtain estimates of the dynamic elastic properties of the rock mass. Brief recommendations regarding future seismic research are given. (author)

Mineral and rock chemistry of Mata da Corda Kamafugitic Rocks (Minas Gerais State, Brazil)

International Nuclear Information System (INIS)

Albuquerque Sgarbi, Patricia B. de; Valenca, Joel G.

1995-01-01

The volcanic rocks of the Mata da Corda Formation (Upper Cretaceous) in Minas Gerais, Brazil, are mafic potassic to ultra potassic rocks of kamafugitic affinity containing essentially clinopyroxenes, perovskite, magnetite and occasionally olivine, phlogopite, melilite pseudomorphs and apatite. The felsic phases are kalsilite and/or leucite pseudomorphs. The rocks are classified as mafitites, leucitites and kalsilitites. The analysis of the available data of the rocks studied, based on the relevant aspects of the main proposals for the classification of alkaline mafic to ultramafic potassic rocks leads to the conclusion that Sahama's (1974) proposal to divide potassium rich alkaline rocks in two large families is the one to which the Mata da Corda rocks adapt best. According to this and the data in the literature on the mineralogy and mineral and rock chemistries of the other similar occurrences, these rocks may be interpreted as alkaline potassic to ultra potassic rocks of hamafugitic affinity. 11 figs., 5 tabs

Use of Rat Estrus Serum for in Vitro Maturation of Bovine Oocytes

Directory of Open Access Journals (Sweden)

AR Rafati

2007-04-01

Full Text Available Introduction: Superovulation produces complications in some patients, so invitro maturation of oocytes is used to decrease or eliminate these complications and improve IVF. Moreover, IVM is used for different aspects of reproductive researches. Slaughterhouse ovaries are the main source of oocytes for IVM and IVF studies. Different media has been introduced and experimented for in vitro maturation of oocytes. Animal's serum at estrus stage contains different hormones and proteins which are essential for oocyte maturation. The aim of this study was to compare three culture media for in vitro maturation (IVM of bovine oocytes; 1(controlTCM-199, 2HCG and follicular fluid (FF and 3 antibiotic. Methods: Rat estrus serum (RSS or fetal bovine serum (FBS was added to control medium. Total of 1789 compact cumulus oocyte complexes (COCs were aspirated from ovaries of slaughtered animals. Oocytes were randomly cultured in mentioned media and incubated in 38.5◦c, 5% CO2 and 95% humidity for 24 hours. The maturation of oocytes was judged according to cumulus cell expansion or randomly orcein stained oocytes and observation of polar bodies. Results: The results showed that maturation rate was significantly higher in second and third group (90.2%, 78.7% as compared to the control group (p<0.001. There was no significant difference between second and third groups (90.2 % vs. 86.6%. Conclusion: RSS is as effective as FBS for IVM of bovine oocytes and can be used as an alternative.

Natural radionuclides in the rocks of the Valle del Cervo Pluton in Piedmont.

Science.gov (United States)

Sesana, Lucia; Fumagalli, Marco; Carnevale, Mauro; Polla, Giancarla; Facchini, Ugo; Colombo, Annita; Tunesi, Annalisa; De Capitani, Luisa; Rusconi, Rosella

2006-01-01

Monitoring of the gamma radiation in Valle del Cervo Pluton was performed by determining U and Th contents in the main rock types cropping out over the entire area and pertaining to the granitic complex, syenitic complex and monzonitic complex. In particular, syenitic rocks were largely used as building and ornamental materials (e.g. Sienite della Balma). All the samples are fresh and do not present joints or fractures filled with U minerals. In the crushed samples the activity of uranium varies from 346 to 764 Bq/kg. Concentration of thorium varies from 202 to 478 Bq/kg. For all the analysed rocks uranium activity is higher than thorium one. The lowest value of radioactive concentration is referred to rocks of the granitic complex. The most active rocks are syenites. The data confirm the high activities of Valle del Cervo rock types, strongly connected with high K content of the source magma (geochemical signature); on the contrary, the activity seems to be not related to the location of the samples.

Maturity Models Development in IS Research

DEFF Research Database (Denmark)

Lasrado, Lester Allan; Vatrapu, Ravi; Andersen, Kim Normann

2015-01-01

Maturity models are widespread in IS research and in particular, IT practitioner communities. However, theoretically sound, methodologically rigorous and empirically validated maturity models are quite rare. This literature review paper focuses on the challenges faced during the development...... literature reveals that researchers have primarily focused on developing new maturity models pertaining to domain-specific problems and/or new enterprise technologies. We find rampant re-use of the design structure of widely adopted models such as Nolan’s Stage of Growth Model, Crosby’s Grid, and Capability...... Maturity Model (CMM). Only recently have there been some research efforts to standardize maturity model development. We also identify three dominant views of maturity models and provide guidelines for various approaches of constructing maturity models with a standard vocabulary. We finally propose using...

Pb, Sr and Nd isotope geological characteristics and its evolution of Jianchaling rock

International Nuclear Information System (INIS)

Pang Chunyong; Chen Minyang; Xu Wenxin

2003-01-01

It has been a long time debatable subject on the raw material source and its genesis of Jianchaling ultrabasic rock, because the original rock phases, the original mineral compositions, texture and structure, even part of the chemical components of the rocks had been changed completely after many periods and phases of metamorphism. According to the content of Pb, Rb, Sr, Nd elements and their Pb, Sr, Nd isotope compositions of the rocks, together with the isotope geological age of late magmatic activities, the authors analyze the evolution of Pb, Sr, Nd isotope compositions, The inferred initiate Nd isotope ratio of ultrabasic rocks is 0.510233, lower than that of meteorite unity at a corresponding period, its ε Nd(T)>O; The initiate Sr ratios inferred by the isotope geological age ranges from 0.702735 to 0.719028; Projecting the lead isotope compositions on the Pb tectonic evolution model, the result indicates that the raw material of Jianchaling ultrabasic rock coming from the deplete upper mantle. The ultrabasic magma which enrich of Mg, Ni and less S intruded the crust and formed the Jianchaling ultrabasic rock at late Proterozoic era (927 Ma±). The forming time of serpentinite is mostly equal to the granitoid intruding time, showing the intrusion o flate acidic magma caused a large scale alteration of the ultrabasic rocks and formed the meta-ultrabasic phase rock observed today. (authors)

Comparison of Efficacy of Endogenous and Exogenous IGF-I in Stimulating Matrix Production in Neonatal and Mature Chondrocytes.

Science.gov (United States)

Aguilar, Izath N; Trippel, Stephen B; Shi, Shuiliang; Bonassar, Lawrence J

2015-10-01

The goal of this study was to compare the efficacy of endogenous upregulation of IGF-I by gene therapy and exogenous addition of insulin-like growth factor I (IGF-I) in enhancing proteoglycan synthesis by skeletally mature and neonatal chondrocytes. Chondrocyte transplantation therapy is a common treatment for focal cartilage lesions, with both mature and neonatal chondrocytes used as a cell source. Additionally, gene therapy strategies to upregulate growth factors such as IGF-I have been proposed to augment chondrocyte transplantation therapies. Both skeletally mature and neonatal chondrocytes were exposed to either an adeno-associated virus-based plasmid containing the IGF-I gene or exogenous IGF-I. Analysis of IGF-I and glycosaminoglycan production using a 4-parameter dose-response model established a clear connection between the amount of IGF-I produced by cells and their biosynthetic response. Both neonatal and mature chondrocytes showed this relationship, but the sensitivities were quite different, with EC50 of 0.57 ng/mL for neonatal chondrocytes and EC50 of 8.70 ng/mL IGF-I for skeletally mature chondrocytes. These data suggest that IGF-I gene therapy may be more effective with younger cell sources. Both cell types were less sensitive to exogenous IGF-I than endogenous IGF-I.

Modeling non-maturing liabilities

OpenAIRE

von Feilitzen, Helena

2011-01-01

Non‐maturing liabilities, such as savings accounts, lack both predetermined maturity and reset dates due to the fact that the depositor is free to withdraw funds at any time and that the depository institution is free to change the rate. These attributes complicate the risk management of such products and no standardized solution exists. The problem is important however since non‐maturing liabilities typically make up a considerable part of the funding of a bank. In this report different mode...

Glaciation of alpine valleys: The glacier - debris-covered glacier - rock glacier continuum

Science.gov (United States)

Anderson, Robert S.; Anderson, Leif S.; Armstrong, William H.; Rossi, Matthew W.; Crump, Sarah E.

2018-06-01

Alpine ice varies from pure ice glaciers to partially debris-covered glaciers to rock glaciers, as defined by the degree of debris cover. In many low- to mid-latitude mountain ranges, the few bare ice glaciers that do exist in the present climate are small and are found where snow is focused by avalanches and where direct exposure to radiation is minimized. Instead, valley heads are more likely to be populated by rock glaciers, which can number in the hundreds. These rock-cloaked glaciers represent some of the most identifiable components of the cryosphere today in low- to mid-latitude settings, and the over-steepened snouts pose an often overlooked hazard to travel in alpine terrain. Geomorphically, rock glaciers serve as conveyor belts atop which rock is pulled away from the base of cliffs. In this work, we show how rock glaciers can be treated as an end-member case that is captured in numerical models of glaciers that include ice dynamics, debris dynamics, and the feedbacks between them. Specifically, we focus on the transition from debris-covered glaciers, where the modern equilibrium line altitude (ELA) intersects the topography, to rock glaciers, where the modern ELA lies above the topography. On debris-covered glaciers (i.e., glaciers with a partial rock mantle), rock delivered to the glacier from its headwall, or from sidewall debris swept into the glacier at tributary junctions, travels englacially to emerge below the ELA. There it accumulates on the surface and damps the rate of melt of underlying ice. This allows the termini of debris-covered glaciers to extend beyond debris-free counterparts, thereby decreasing the ratio of accumulation area to total area of the glacier (AAR). In contrast, rock glaciers (i.e., glaciers with a full rock mantle) occur where and when the environmental ELA rises above the topography. They require avalanches and rockfall from steep headwalls. The occurrence of rock glaciers reflects this dependence on avalanche sources

Determining the source and genetic fingerprint of natural gases using noble gas geochemistry: a northern Appalachian Basin case study

Science.gov (United States)

Hunt, Andrew G.; Darrah, Thomas H.; Poreda, Robert J.

2012-01-01

Silurian and Devonian natural gas reservoirs present within New York state represent an example of unconventional gas accumulations within the northern Appalachian Basin. These unconventional energy resources, previously thought to be noneconomically viable, have come into play following advances in drilling (i.e., horizontal drilling) and extraction (i.e., hydraulic fracturing) capabilities. Therefore, efforts to understand these and other domestic and global natural gas reserves have recently increased. The suspicion of fugitive mass migration issues within current Appalachian production fields has catalyzed the need to develop a greater understanding of the genetic grouping (source) and migrational history of natural gases in this area. We introduce new noble gas data in the context of published hydrocarbon carbon (C1,C2+) (13C) data to explore the genesis of thermogenic gases in the Appalachian Basin. This study includes natural gases from two distinct genetic groups: group 1, Upper Devonian (Marcellus shale and Canadaway Group) gases generated in situ, characterized by early mature (13C[C1  C2][13C113C2]: –9), isotopically light methane, with low (4He) (average, 1  103 cc/cc) elevated 4He/40Ar and 21Ne/40Ar (where the asterisk denotes excess radiogenic or nucleogenic production beyond the atmospheric ratio), and a variable, atmospherically (air-saturated–water) derived noble gas component; and group 2, a migratory natural gas that emanated from Lower Ordovician source rocks (i.e., most likely, Middle Ordovician Trenton or Black River group) that is currently hosted primarily in Lower Silurian sands (i.e., Medina or Clinton group) characterized by isotopically heavy, mature methane (13C[C1 – C2] [13C113C2]: 3), with high (4He) (average, 1.85  103 cc/cc) 4He/40Ar and 21Ne/40Ar near crustal production levels and elevated crustal noble gas content (enriched 4He,21Ne, 40Ar). Because the release of each crustal noble gas (i.e., He, Ne, Ar

Slab replacement maturity guidelines.

Science.gov (United States)

2014-04-01

This study investigated the use of maturity method to determine early age strength of concrete in slab : replacement application. Specific objectives were (1) to evaluate effects of various factors on the compressive : maturity-strength relationship ...

Rock History and Culture

OpenAIRE

Gonzalez, Éric

2013-01-01

Two ambitious works written by French-speaking scholars tackle rock music as a research object, from different but complementary perspectives. Both are a definite must-read for anyone interested in the contextualisation of rock music in western popular culture. In Une histoire musicale du rock (i.e. A Musical History of Rock), rock music is approached from the point of view of the people – musicians and industry – behind the music. Christophe Pirenne endeavours to examine that field from a m...

Rock-Bound Arsenic Influences Ground Water and Sediment Chemistry Throughout New England

Science.gov (United States)

Robinson, Gilpin R.; Ayotte, Joseph D.

2007-01-01

The information in this report was presented at the Northeastern Region Geological Society of America meeting held March 11-14, 2007, in Durham, New Hampshire. In the New England crystalline bedrock aquifer, concentrations of arsenic that exceed the drinking water standard of 10 ?g/L occur most frequently in ground water from wells sited in specific metamorphic and igneous rock units. Geochemical investigations indicate that these geologic units typically have moderately elevated whole-rock concentrations of arsenic compared to other rocks in the region. The distribution of ground water wells with As > 5 ?g/L has a strong spatial correlation with specific bedrock units where average whole-rock concentrations of arsenic exceed 1.1 mg/kg and where geologic and geochemical factors produce high pH ground water. Arsenic concentrations in stream sediments collected from small drainages reflect the regional distribution of this natural arsenic source and have a strong correlation with both rock chemistry and the distribution of bedrock units with elevated arsenic chemistry. The distribution of ground water wells with As > 5 ?g/L has a strong spatial correlation with the distribution of stream sediments where concentrations of arsenic exceed 6 mg/kg. Stream sediment chemistry also has a weak correlation with the distribution of agricultural lands where arsenical pesticides were used on apple, blueberry, and potato crops. Elevated arsenic concentrations in bedrock wells, however, do not correlate with agricultural areas where arsenical pesticides were used. These results indicate that both stream sediment chemistry and the solubility and mobility of arsenic in ground water in bedrock are influenced by host-rock arsenic concentrations. Stream sediment chemistry and the distribution of geologic units have been found to be useful parameters to predict the areas of greatest concern for elevated arsenic in ground water and to estimate the likely levels of human exposure to

Big Rock Point: 35 years of electrical generation

International Nuclear Information System (INIS)

Petrosky, T.D.

1998-01-01

On September 27, 1962, the 75 MWe boiling water reactor, designed and built by General Electric, of the Big Rock Point Nuclear Power Station went critical for the first time. The US Atomic Energy Commission (AEC) and the plant operator, Consumers Power, had designed the plant also as a research reactor. The first studies were devoted to fuel behavior, higher burnup, and materials research. The reactor was also used for medical technology: Co-60 radiation sources were produced for the treatment of more than 120,000 cancer patients. After the accident at the Three Mile Island-2 nuclear generating unit in 1979, Big Rock Point went through an extensive backfitting phase. Personnel from numerous other American nuclear power plants were trained at the simulator of Big Rock Point. The plant was decommissioned permanently on August 29, 1997 after more than 35 years of operation and a cumulated electric power production of 13,291 GWh. A period of five to seven years is estimated for decommissioning and demolition work up to the 'green field' stage. (orig.) [de

Maturity effects in energy futures

Energy Technology Data Exchange (ETDEWEB)

Serletis, Apostolos (Calgary Univ., AB (CA). Dept. of Economics)

1992-04-01

This paper examines the effects of maturity on future price volatility and trading volume for 129 energy futures contracts recently traded in the NYMEX. The results provide support for the maturity effect hypothesis, that is, energy futures prices to become more volatile and trading volume increases as futures contracts approach maturity. (author).

Correlation between Cervical Vertebral Maturation Stages and Dental Maturation in a Saudi Sample

Directory of Open Access Journals (Sweden)

Nayef H Felemban

2017-01-01

Full Text Available Background: The aim of the present study was to compare the cervical vertebra maturation stages method and dental maturity using tooth calcification stages. Methods: The current study comprised of 405 subjects selected from orthodontic patients of Saudi origin coming to clinics of the specialized dental centers in western region of Saudi Arabia. Dental age was assessed according to the developmental stages of upper and lower third molars and skeletal maturation according to the cervical vertebrae maturation stage method. Statistical analysis was done using Kruskal-Wallis H, Mann-Whitney U test, Chi-Square test; t-test and Spearman correlation coefficient for inter group comparison. Results: The females were younger than males in all cervical stages. The CS1-CS2 show the period before the peak of growth, during CS3-CS5 it’s the pubertal growth spurt and CS6 is the period after the peak of the growth. The mean age and standard deviation for cervical stages of CS2, CS3 and CS4 were 12.09 ±1.72 years, 13.19 ±1.62 and 14.88 ±1.52 respectively. The Spearman correlation coefficients between cervical vertebrae and dental maturation were between 0.166 and 0.612, 0.243 and 0.832 for both sexes for upper and lower third molars. The significance levels for all coefficients were equal at 0.01 and 0.05. Conclusion: The results of this study showed that the skeletal maturity increased with the increase in dental ages for both genders. An early rate of skeletal maturation stage was observed in females. This study needs further analysis using a larger sample covering the entire dentition.

Apollo rocks, fines and soil cores

Science.gov (United States)

Allton, J.; Bevill, T.

Apollo rocks and soils not only established basic lunar properties and ground truth for global remote sensing, they also provided important lessons for planetary protection (Adv. Space Res ., 1998, v. 22, no. 3 pp. 373-382). The six Apollo missions returned 2196 samples weighing 381.7 kg, comprised of rocks, fines, soil cores and 2 gas samples. By examining which samples were allocated for scientific investigations, information was obtained on usefulness of sampling strategy, sampling devices and containers, sample types and diversity, and on size of sample needed by various disciplines. Diversity was increased by using rakes to gather small rocks on the Moon and by removing fragments >1 mm from soils by sieving in the laboratory. Breccias and soil cores are diverse internally. Per unit weight these samples were more often allocated for research. Apollo investigators became adept at wringing information from very small sample sizes. By pushing the analytical limits, the main concern was adequate size for representative sampling. Typical allocations for trace element analyses were 750 mg for rocks, 300 mg for fines and 70 mg for core subsamples. Age-dating and isotope systematics allocations were typically 1 g for rocks and fines, but only 10% of that amount for core depth subsamples. Historically, allocations for organics and microbiology were 4 g (10% for cores). Modern allocations for biomarker detection are 100mg. Other disciplines supported have been cosmogenic nuclides, rock and soil petrology, sedimentary volatiles, reflectance, magnetics, and biohazard studies . Highly applicable to future sample return missions was the Apollo experience with organic contamination, estimated to be from 1 to 5 ng/g sample for Apollo 11 (Simonheit &Flory, 1970; Apollo 11, 12 &13 Organic contamination Monitoring History, U.C. Berkeley; Burlingame et al., 1970, Apollo 11 LSC , pp. 1779-1792). Eleven sources of contaminants, of which 7 are applicable to robotic missions, were

Thermomechanical stability of underground installations: significance of the thermophysical properties of rocks

International Nuclear Information System (INIS)

Mirkovich, V.

1981-01-01

When heat is generated in an underground installation, there are several interdependent factors-such as the rate of heat dissipation, changes in this rate with temperature, or the effects of thermal gradients and thermal expansivities-which influence the stability of the rock mass. To evaluate the thermomechanical stability of a proposed site for an underground nuclear power station, rock specimens from a 300 m deep drill core were obtained, and their thermal diffusivity and linear thermal expansion were measured between 25 0 C and 500 0 C. The thermal conductivity was also measured, in the temperature range 100-500 0 C. Under normal operating conditions, heat transfer to the surface of the rock mass surrounding the power installation would be low. However, in some contingencies, this heat load could become large. The results are discussed from the point of view of the stability of a rock enclosure at higher heat fluxes; they indicate that the rocks studied would, in general, not be suitable as an unprotected wall for containment of such a heat source. (author)

Terrigenous sediment supply along the Chilean continental margin: modern regional patterns of texture and composition

Science.gov (United States)

Lamy, F.; Hebbeln, D.; Wefer, G.

The regional patterns of texture and composition of modern continental slope and pelagic sediments off Chile between 25°S and 43°S reflect the latitudinal segmentation of geological, morphological, and climatic features of the continental hinterland. Grain-size characteristics are controlled by the grain-size of source rocks, the weathering regime, and mode of sediment input (eolian off northern Chile vs fluvial further south). Bulk-mineral assemblages reveal a low grade of maturity. Regional variations are governed by the source-rock composition of the different geological terranes and the relative source-rock contribution of the Coastal Range and Andes, as controlled by the continental hydrology. The relative abundance of clay minerals is also predominantly influenced by the source-rock composition and partly by continental smectite neoformation. Latitudinal variations of illite crystallinities along the Chilean continental slope (and west of the Peru-Chile trench) clearly reflect modifications of the weathering regime which correspond to the strong climatic zonation of Chile.