Assessment of Thermal Maturity Trends in Devonian–Mississippian Source Rocks Using Raman Spectroscopy: Limitations of Peak-Fitting Method

Energy Technology Data Exchange (ETDEWEB)

Lupoi, Jason S., E-mail: jlupoi@rjlg.com; Fritz, Luke P. [RJ Lee Group, Inc., Monroeville, PA (United States); Parris, Thomas M. [Kentucky Geological Survey, University of Kentucky, Lexington, KY (United States); Hackley, Paul C. [UniversityS. Geological Survey, Reston, VA (United States); Solotky, Logan [RJ Lee Group, Inc., Monroeville, PA (United States); Eble, Cortland F. [Kentucky Geological Survey, University of Kentucky, Lexington, KY (United States); Schlaegle, Steve [RJ Lee Group, Inc., Monroeville, PA (United States)

2017-09-27

The thermal maturity of shale is often measured by vitrinite reflectance (VRo). VRo measurements for the Devonian–Mississippian black shale source rocks evaluated herein predicted thermal immaturity in areas where associated reservoir rocks are oil-producing. This limitation of the VRo method led to the current evaluation of Raman spectroscopy as a suitable alternative for developing correlations between thermal maturity and Raman spectra. In this study, Raman spectra of Devonian–Mississippian black shale source rocks were regressed against measured VRo or sample-depth. Attempts were made to develop quantitative correlations of thermal maturity. Using sample-depth as a proxy for thermal maturity is not without limitations as thermal maturity as a function of depth depends on thermal gradient, which can vary through time, subsidence rate, uplift, lack of uplift, and faulting. Correlations between Raman data and vitrinite reflectance or sample-depth were quantified by peak-fitting the spectra. Various peak-fitting procedures were evaluated to determine the effects of the number of peaks and maximum peak widths on correlations between spectral metrics and thermal maturity. Correlations between D-frequency, G-band full width at half maximum (FWHM), and band separation between the G- and D-peaks and thermal maturity provided some degree of linearity throughout most peak-fitting assessments; however, these correlations and those calculated from the G-frequency, D/G FWHM ratio, and D/G peak area ratio also revealed a strong dependence on peak-fitting processes. This dependency on spectral analysis techniques raises questions about the validity of peak-fitting, particularly given the amount of subjective analyst involvement necessary to reconstruct spectra. This research shows how user interpretation and extrapolation affected the comparability of different samples, the accuracy of generated trends, and therefore, the potential of the Raman spectral method to become an

Assessment of Thermal Maturity Trends in Devonian–Mississippian Source Rocks Using Raman Spectroscopy: Limitations of Peak-Fitting Method

International Nuclear Information System (INIS)

Lupoi, Jason S.; Fritz, Luke P.; Parris, Thomas M.; Hackley, Paul C.; Solotky, Logan; Eble, Cortland F.; Schlaegle, Steve

2017-01-01

The thermal maturity of shale is often measured by vitrinite reflectance (VRo). VRo measurements for the Devonian–Mississippian black shale source rocks evaluated herein predicted thermal immaturity in areas where associated reservoir rocks are oil-producing. This limitation of the VRo method led to the current evaluation of Raman spectroscopy as a suitable alternative for developing correlations between thermal maturity and Raman spectra. In this study, Raman spectra of Devonian–Mississippian black shale source rocks were regressed against measured VRo or sample-depth. Attempts were made to develop quantitative correlations of thermal maturity. Using sample-depth as a proxy for thermal maturity is not without limitations as thermal maturity as a function of depth depends on thermal gradient, which can vary through time, subsidence rate, uplift, lack of uplift, and faulting. Correlations between Raman data and vitrinite reflectance or sample-depth were quantified by peak-fitting the spectra. Various peak-fitting procedures were evaluated to determine the effects of the number of peaks and maximum peak widths on correlations between spectral metrics and thermal maturity. Correlations between D-frequency, G-band full width at half maximum (FWHM), and band separation between the G- and D-peaks and thermal maturity provided some degree of linearity throughout most peak-fitting assessments; however, these correlations and those calculated from the G-frequency, D/G FWHM ratio, and D/G peak area ratio also revealed a strong dependence on peak-fitting processes. This dependency on spectral analysis techniques raises questions about the validity of peak-fitting, particularly given the amount of subjective analyst involvement necessary to reconstruct spectra. This research shows how user interpretation and extrapolation affected the comparability of different samples, the accuracy of generated trends, and therefore, the potential of the Raman spectral method to become an

Assessment of Thermal Maturity Trends in Devonian–Mississippian Source Rocks Using Raman Spectroscopy: Limitations of Peak-Fitting Method

Directory of Open Access Journals (Sweden)

Jason S. Lupoi

2017-09-01

Full Text Available The thermal maturity of shale is often measured by vitrinite reflectance (VRo. VRo measurements for the Devonian–Mississippian black shale source rocks evaluated herein predicted thermal immaturity in areas where associated reservoir rocks are oil-producing. This limitation of the VRo method led to the current evaluation of Raman spectroscopy as a suitable alternative for developing correlations between thermal maturity and Raman spectra. In this study, Raman spectra of Devonian–Mississippian black shale source rocks were regressed against measured VRo or sample-depth. Attempts were made to develop quantitative correlations of thermal maturity. Using sample-depth as a proxy for thermal maturity is not without limitations as thermal maturity as a function of depth depends on thermal gradient, which can vary through time, subsidence rate, uplift, lack of uplift, and faulting. Correlations between Raman data and vitrinite reflectance or sample-depth were quantified by peak-fitting the spectra. Various peak-fitting procedures were evaluated to determine the effects of the number of peaks and maximum peak widths on correlations between spectral metrics and thermal maturity. Correlations between D-frequency, G-band full width at half maximum (FWHM, and band separation between the G- and D-peaks and thermal maturity provided some degree of linearity throughout most peak-fitting assessments; however, these correlations and those calculated from the G-frequency, D/G FWHM ratio, and D/G peak area ratio also revealed a strong dependence on peak-fitting processes. This dependency on spectral analysis techniques raises questions about the validity of peak-fitting, particularly given the amount of subjective analyst involvement necessary to reconstruct spectra. This research shows how user interpretation and extrapolation affected the comparability of different samples, the accuracy of generated trends, and therefore, the potential of the Raman spectral

Geochemical characteristics of Lower Jurassic source rocks in the Zhongkouzi Basin

Science.gov (United States)

Niu, Haiqing; Han, Xiaofeng; Wei, Jianshe; Zhang, Huiyuan; Wang, Baowen

2018-01-01

Zhongkouzi basin is formed in Mesozoic and Cenozoic and developed on the Hercynian folded belt, the degree of exploration for oil and gas is relatively low hitherto. In order to find out the geochemical characteristics of the source rocks and the potentials for hydrocarbon generation. The research result shows that by analysis the geochemical characteristics of outcrop samples and new core samples in Longfengshan Group, Longfengshan Group are most developed intervals of favorable source rocks. They are formed in depression period of the basin when the sedimentary environments is salt water lacustrine and the water is keeping stable; The organic matter abundance is middle-higher, the main kerogen type is II1-II2 and few samples act as III type, The organic matter maturity is low maturity to medium maturity. The organic matter maturity of the source rock from eastern part of the basin is higher than in the western region. The source rock of Longfengshan Group are in the hydrocarbon generation threshold. The great mass of source rocks are matured and in the peak stage of oil generation.

Source rock

Directory of Open Access Journals (Sweden)

Abubakr F. Makky

2014-03-01

Full Text Available West Beni Suef Concession is located at the western part of Beni Suef Basin which is a relatively under-explored basin and lies about 150 km south of Cairo. The major goal of this study is to evaluate the source rock by using different techniques as Rock-Eval pyrolysis, Vitrinite reflectance (%Ro, and well log data of some Cretaceous sequences including Abu Roash (E, F and G members, Kharita and Betty formations. The BasinMod 1D program is used in this study to construct the burial history and calculate the levels of thermal maturity of the Fayoum-1X well based on calibration of measured %Ro and Tmax against calculated %Ro model. The calculated Total Organic Carbon (TOC content from well log data compared with the measured TOC from the Rock-Eval pyrolysis in Fayoum-1X well is shown to match against the shale source rock but gives high values against the limestone source rock. For that, a new model is derived from well log data to calculate accurately the TOC content against the limestone source rock in the study area. The organic matter existing in Abu Roash (F member is fair to excellent and capable of generating a significant amount of hydrocarbons (oil prone produced from (mixed type I/II kerogen. The generation potential of kerogen in Abu Roash (E and G members and Betty formations is ranging from poor to fair, and generating hydrocarbons of oil and gas prone (mixed type II/III kerogen. Eventually, kerogen (type III of Kharita Formation has poor to very good generation potential and mainly produces gas. Thermal maturation of the measured %Ro, calculated %Ro model, Tmax and Production index (PI indicates that Abu Roash (F member exciting in the onset of oil generation, whereas Abu Roash (E and G members, Kharita and Betty formations entered the peak of oil generation.

The potentiality of hydrocarbon generation of the Jurassic source rocks in Salam-3x well,

Directory of Open Access Journals (Sweden)

Mohamed M. El Nady

2016-03-01

Full Text Available The present work deals with the identification of the potential and generating capability of oil generation in the Jurassic source rocks in the Salam-3x well. This depending on the organo-geochemical analyses of cutting samples representative of Masajid, Khatatba and Ras Qattara formations, as well as, representative extract samples of the Khatatba and Ras Qattara formations. The geochemical analysis suggested the potential source intervals within the encountered rock units as follows: Masajid Formation bears mature source rocks and have poor to fair generating capability for generating gas (type III kerogen. Khatatba Formation bears mature source rock, and has poor to good generating capability for both oil and gas. Ras Qattara Formation constituting mature source rock has good to very good generating capability for both oil and gas. The burial history modeling shows that the Masajid Formation lies within oil and gas windows; Khatatba and Ras Qattara formations lie within the gas window. From the biomarker characteristics of source rocks it appears that the extract is genetically related as the majority of them were derived from marine organic matters sources (mainly algae deposited under reducing environment and take the direction of increasing maturity and far away from the direction of biodegradation. Therefore, Masajid Formation is considered as effective source rocks for generating hydrocarbons, while Khatatba and Ras Qattara formations are the main source rocks for hydrocarbon accumulations in the Salam-3x well.

Origin of a Tertiary oil from El Mahafir wildcat & geochemical correlation to some Muglad source rocks, Muglad basin, Sudan

Science.gov (United States)

Fadul Abul Gebbayin, Omer. I. M.; Zhong, Ningning; Ali Ibrahim, Gulfan; Ali Alzain, Mohamed

2018-01-01

Source rock screening analysis was performed on four stratigraphic units from the Muglad basin namely; Abu Gabra, Zarqa, Ghazal, and Baraka formations using pyrolysis and Vitrinite Reflectance (Ro). Results, integrated with the chromatographic and isotopic data from these rocks extracts and a Tertiary oil from El Mahafir-1 wild cat, were used to determine the origin of the oil. A good organic source within the Middle Abu Gabra Formation is observed in wells El Toor-6 and Neem Deep-1 (TOC, 1.0-2.0% & S2 5.0-10.0 mg C/g rock), with mixed kerogens I, II, & III, and thermally mature (% Ro = 0.74-0.94). The Campanian-Early Maastrichtian sequence, i.e. Zarqa and Ghazal formations are generally poor (TOC, diversity, both in space and time and is characterized by dominant algal input at some areas and or stratigraphic intervals [Elevated tricyclics, higher C29/C30 hopanes (0.5-1.14), and relatively low Gammacerane indices (4.6-14.4)], while mixed with abundant terrigenous material at others. A direct correlation between El Mahafir oil and the Abu Gabra extracts is thus inferred based on: its mixed organic source nature, oxic to sub-oxic depositional environment (Pr/Ph 1.22), relatively low C29/C30 hopanes (0.54), low C28 steranes (29%), and a high gammacerane index (20.5). This is largely supported by the maturity modeling results which suggest generation is only from the Abu Gabra at this location.

Mining and oil. Oil shale's contribution to future oil supply; Bergbau und Oel. Der Beitrag des Oelschiefers zur Oelversorgung

Energy Technology Data Exchange (ETDEWEB)

Linden, Eike von der [Linden Advisory, Dreieich (Germany)

2012-05-15

Crude oil contributes in Germany and globally approximately one third to the consumption of primary energies and actually is and in the foreseeable future will be the most important energy source. Recently shale oil as an unconventional oil has gained attention in public discussions. Depending on temperatures oil shale contains either already matured fluid shale oil or immature waxy kerogen. For determination of kerogen containing oil shale and shale oil common definitions for fluid hydrocarbons will be presented. Fluid hydrocarbons (molecular chains > C{sub 5}H{sub 12}) originate from animal substance which had been settled millions of years in sediments on sea- or lakebeds under anaerobic conditions. High pressure and high temperatures effect conversion to hydrocarbons. With sufficient permeability the liquid hydrocarbons migrate from the sediment as the source rock and get assembled in porous rocks under the cover of an impermeable rock strata, in so called entrapment structures. In case there is no impermeable rock strate the hydrocarbons will diffuse into the atmosphere. The hydrocarbons in entrapment structures are called conventional oil and are extracted by drilling wells. The extractable oil as part of the oil in place depends on the viscosity of the oil, the permeability of the host rock and applied exploitation methods which can affect pressure, viscosity and permeability. The exploitation achieves 30 to 50% of the oil in place. When the source rock consisting of strata hundreds of meters thick is not sufficiently permeable the matured hydrocarbons remain at its place of origination. These hydrocarbons are called shale oil and belong to the unconventional oil resources. For exploitation of shale oil by wells the source rock must be treated by intensive energy input, amongst others, by fracking which creates artificial permeability and by pressure which affects migration of the hydrocarbons to the well. The exploitation methods for shale oil do not

Oil(Gas) - source rock correlation technique

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-01

The overview of bio-marker parameters which are applicable to hydrocarbon exploration has been illustrated. Experimental analysis of saturated hydrocarbon and bio-markers of the Pohang E and F core samples has been carried out. Samples were extracted by stirring in dichloromethane at 40-50 degree for 10 hours. The saturated, aromatic and resin fractions of the extract were obtained using thin layer chromatograms. The relative abundance of normal alkane fraction of the samples is low except lowest interval, which is probably due to the biodegradation. The bio-marker assemblage of hopanoids and steranes has been characterized. According to the analysis of saturated hydrocarbons and bio-markers, the sedimentary environment of the Pohang core samples is marine and transitional zone except the terrestrial environment of the lowest samples such as 610.5 m from E core and 667.2 m from F core. The thermal maturity through the studied interval did not reach oil window even though slight increase in thermal maturity with depth, which coincide with Rock Eval pyrolysis data. In order to check the validation of analysis of the bio-markers, same samples were analyzed by the University of Louis Pasteur, France. The distribution and relative peak area of the bio-markers were identical with those by laboratory of KIGAM. For the 2 nd stage of the research, analysis of bio-markers other than hopanoids and steranes should be continued. (author). 29 figs., 7 tabs.

Early-maturing soybean cropping system. III. Protein and oil contents and oil composition

International Nuclear Information System (INIS)

Kane, M.V.; Steele, C.C.; Grabau, L.J.; MacKown, C.T.; Hildebrand, D.F.

1997-01-01

Expanding production of early-maturing soybean [Glycine max (L.) Merrill] cultivars in the southeastern USA has exposed such cultivars to a wide range of environmental conditions during seed-fill. Temperatures during this growth stage influence levels of specific fatty acids, particularly of the unsaturated fatty acids. Our objective was to evaluate the grain quality responses of early-maturing cultivars to the wide range of planting dates in the southeastern USA. Protein and oil contents along with fatty acid profiles were assessed for cultivars from Maturity Group (MG) 00 through IV using late April mid-May early June, and late June planting dates on a well-drained Maury silt loam (fine, mixed, mesic Typic Paleudalf) in 1990 through 1993. Across years and cultivars. delayed planting increased protein content and linolenic acid levels and reduced oil content and oleic acid levels but had little or no influence on palmitic stearic or linoleic acid levels. The higher seed-fill temperatures associated with early planting were strongly correlated with increased oil content and oleic acid levels and reduced linolenic acid levels. Increasing seed-fill temperatures were closely associated with reduced linolenic acid levels for all six cultivars. However, the oleic acid response to seed-temperatures strongly depended on cultivar maturity. Oleic acid levels of early-maturing cultivars were much more sensitive to seed-fill temperatures than were those of later maturing cultivars. While other effects of environment on grain quality characteristics may be relatively small perhaps the quality of new low linolenic acid cultivars could be amplified through culture under the warmer conditions the southeastern USA

Maturation history modeling of Sufyan Depression, northwest Muglad Basin, Sudan

Science.gov (United States)

Wang, Ying; Liu, Luofu; An, Fuli; Wang, Hongmei; Pang, Xiongqi

2016-08-01

The Sufyan Depression is located in the northwest of Muglad Basin and is considered as a favorable exploration area by both previous studies and present oil shows. In this study, 16 wells are used or referred, the burial history model was built with new seismic, logging and well data, and the thermal maturity (Ro, %) of proved AG source rocks was predicted based on heat flow calculation and EASY %Ro modeling. The results show that the present heat flow range is 36 mW/m2∼50 mW/m2 (average 39 mW/m2) in 13 wells and 15 mW/m2∼55 mW/m2 in the whole depression. Accordingly, the geothermal gradient is 20 °C/km∼26 °C/km and 12 °C/km∼30 °C/km, respectively. The paleo-heat flow has three peaks, namely AG-3 period, lower Bentiu period and Early Paleogene, with the value decreases from the first to the last, which is corresponding to the tectonic evolution history. Corresponding to the heat flow distribution feature, the AG source rocks become mature earlier and have higher present marurity in the south area. For AG-2_down and AG-3_up source rocks that are proved to be good-excellent, most of them are mature with Ro as 0.5%-1.1%. But they can only generate plentiful oil and gas to charge reservoirs in the middle and south areas where their Ro is within 0.7%-1.1%, which is consistent with the present oil shows. Besides, the oil shows from AG-2_down reservoir in the middle area of the Sufyan Depression are believed to be contributed by the underlying AG-3_up source rock or the source rocks in the south area.

RADIATION CHEMICAL CONVERSION OF OIL DERIVED FROM OIL-BITUMEN ROCK

Directory of Open Access Journals (Sweden)

Lala Jabbarova

2014-06-01

Full Text Available The results of research in the radiation processing of synthetic oil derived from oil–bitumen rock of the Balakhany deposit in Azerbaijan are presented. The study has been conducted on a 60Co gamma-source at a dose rate of P = 0.5 Gy/s and various absorbed doses of D = 43–216 kGy. Samples of synthetic oil from natural bitumen rocks have been analyzed by chromatography, gas chromatography–mass spectrometry, and IR-spectroscopy, and their radiation resistance has been evaluated. The results of the study allow for both assessment of the feasibility of manufacturing petrochemicals for various applications by radiation processing and use of these materials for isolating radioactive sources to preclude their impact on the environment.

Cracking and thermal maturity of Ordovician oils from Tahe Oilfield, Tarim Basin, NW China

Directory of Open Access Journals (Sweden)

Anlai Ma

2017-12-01

Full Text Available The thermal maturity of the Ordovician oils from the Tahe oilfield of Tarim Basin, NW China was assessed through various maturity parameters, such as biomarkers, aromatic parameters, and diamondoid parameters. Both Ts/(Ts+Tm and C29Ts/(C29H+C29Ts values indicate that the maturity of oils has not reached the condensates stage, which is consistent with the maturity obtained by MPI1. However, the diamondoid maturity suggests that the oil maturity ranges 1.1%–1.6% Ro, which is apparently higher than that of the maturity obtained by the biomarker and MPI1. This discrepancy in maturity may indicate that the Ordovician reservoir has multiple filling history. The 4-MD+3-MD concentration of oils disperses and increases slowly when the Ts/(Ts+Tm value is lower than 0.55. Meanwhile, the value increases rapidly when the Ts/(Ts+Tm value is higher than 0.55. It is proposed that the diamondoid baseline is about 15 μg/goil for marine oils in the Tahe oilfield based on the diamondoid concentration of marine oils from reservoirs of various age. The concentration of 4-MD+3-MD of most Ordovician oils generally ranges from 4.5 to 35 μg/goil, suggesting that the degree of oil-cracking is lower than 50% and the deep Ordovician have potential of oil exploration. The distribution of the concentration of 4-MD+3-MD is characterized by being high in the east and south, low in the west and north, proposing that the two migration pathways exit in the oilfield, which are from east to west and from south to north, respectively. The migration directions are consistent with the results obtained from the oil density and the maturity parameters such as Ts/(Ts+Tm. Thus, suggesting the concentration of 4-MD+3-MD can be used as migration index in oilfield scale.

The determination of maturity levels in source rocks of the La Luna Formation, Maracaibo Basin, Venezuela, based on convention geochemical parameters and asphaltenes; Determinacao do grau de maturacao em rochas geradoras de petroleo, formacao La Luna, Bacia de Maracaibo, Venezuela: parametros geoquimicos convencionais e asfaltenos

Energy Technology Data Exchange (ETDEWEB)

Castro, L.P. de [Pontificia Universidade Catolica (PUC-RS), Porto Alegre, RS (Brazil). Centro de Excelencia em Pesquisas sobre o Armazenamento de Carbono; Franco, N. [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil). Dept. de Geologia; Lopez, L.; Lo Monaco, S.; Escobar, G. [Universidad Central de Venezuela (UCV), Caracas (Venezuela); Kalkreuth, W. [Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alegre, RS (Brazil). Centro de Excelencia em Analises de Carvao e Rochas Geradoras de Petroleo

2008-07-01

The La Luna Formation, main source rock of the Maracaibo Basin was studied by conventional geochemical parameters, used to determine the maturity, and they were compared with the physic-chemical and molecular properties of the asphaltenes present in the bitumen of the rocks. Three wells were studied (A, B and C) with a total of 13 samples. Based on Rock-Eval results the organic matter in well A (455 deg C Tmax) shows a relatively high level of maturation (top of the oil window), whereas the organic matter in well B (435 - 436 deg C Tmax) is in the beginning of the oil window. Tmax values in well C (438 - 446 deg C) and well C suggest an intermediate maturity level. The biomarkers identified in well B and C show ratios indicating an equilibrium state in the maturity level. A good correlation was found comparing the conventional analytical data with the determination of maturity level obtained from the asphaltenes precipitated from the bitumen of the samples. With increased maturity levels the H1 NMR analysis showed enrichment in aromatic molecules in relation to aliphatic, due to the bitumen aromatization process. Similarly, the asphaltenes molecular weight has higher values in samples characterized by elevated maturity levels. This confirms earlier studies that showed that asphaltenes may be utilized as maturity parameter of organic matter. (author)

Hydrocarbon potential of Ordovician and Silurian rocks. Siljan Region (Sweden)

Energy Technology Data Exchange (ETDEWEB)

Berner, U. [Bundesanstalt fuer Geowissenschaften und Rohstoffe (BGR), Hannover (Germany); Lehnert, O. [Erlangen-Nuernberg Univ., Erlangen (Germany); Meinhold, G. [Goettingen Univ. (Germany)

2013-08-01

Hydrocarbon exploration in the vicinity of Europe's largest impact structure (Siljan, Central Sweden) focused for years on abiogenic concepts and largely neglected state of the art knowledge on hydrocarbon generation via thermal decomposition of organic matter. In our study we use sedimentary rocks obtained from three drill sites (Mora001, Stumsnaes 1 and Solberga 1) within the ring structure around the central uplift to investigate the hydrocarbon potential of Ordovician and Silurian strata of the region and also for comparison with the shale oil and gas potential of age equivalent rocks of the Baltic Sea. Elemental analyses provided information on concentrations of carbonate and organic carbon, total sulfur as well as on the composition of major and minor elements of the sediments. The data has been used to evaluate the depositional environment and possible diagenetic alterations of the organic matter. RockEval pyrolysis and solvent hydrocarbon extraction gave insight into the hydrocarbon generation potential and the type and thermal maturity of the sediments. From the geochemistry data of the studied wells it is obvious that changes of depositional environments (lacustrine - marine) have occurred during Ordovician and Silurian times. Although, the quality of the organic matter has been influenced in marine and brackish environments through sulfate reduction, we observe for a number of marine and lacustrine sediments a good to excellent preservation of the biological precursors which qualify the sediments as hydrocarbon source rocks (Type II kerogens). Lacustrine source rocks show a higher remaining hydrocarbon potential (up to {proportional_to}550 mg HC per g C{sub org}) than those of marine or brackish environments. Our investigations indicate that the thermal maturity of organic matter of the drill sites has reached the initial stage of oil generation. However, at Mora001 some of the sediments were stained with oil indicating that hydrocarbons have

Electrokinetic mechanism of wettability alternation at oil-water-rock interface

Science.gov (United States)

Tian, Huanhuan; Wang, Moran

2017-12-01

Design of ions for injection water may change the wettability of oil-brine-rock (OBR) system, which has very important applications in enhanced oil recovery. Though ion-tuned wettability has been verified by various experiments, the mechanism is still not clear. In this review paper, we first present a comprehensive summarization of possible wettability alteration mechanisms, including fines migration or dissolution, multicomponent ion-exchange (MIE), electrical double layer (EDL) interaction between rock and oil, and repulsive hydration force. To clarify the key mechanism, we introduce a complete frame of theories to calculate attribution of EDL repulsion to wettability alteration by assuming constant binding forces (no MIE) and rigid smooth surface (no fines migration or dissolution). The frame consists of three parts: the classical Gouy-Chapman model coupled with interface charging mechanisms to describe EDL in oil-brine-rock systems, three methods with different boundary assumptions to evaluate EDL interaction energy, and the modified Young-Dupré equation to link EDL interaction energy with contact angle. The quantitative analysis for two typical oil-brine-rock systems provides two physical maps that show how the EDL interaction influences contact angle at different ionic composition. The result indicates that the contribution of EDL interaction to ion-tuned wettability for the studied system is not quite significant. The classical and advanced experimental work using microfabrication is reviewed briefly on the contribution of EDL repulsion to wettability alteration and compared with the theoretical results. It is indicated that the roughness of real rock surface may enhance EDL interaction. Finally we discuss some pending questions, perspectives and promising applications based on the mechanism.

INCREASED OIL RECOVERY FROM MATURE OIL FIELDS USING GELLED POLYMER TREATMENTS

Energy Technology Data Exchange (ETDEWEB)

G.P. Willhite; D.W. Green; C.S. McCool

2003-05-01

Gelled polymer treatments are applied to oil reservoirs to increase oil production and to reduce water production by altering the fluid movement within the reservoir. This report describes the results of a three-year research program aimed at reducing barriers to the widespread use of gelled polymer treatments by (1) developing methods to predict gel behavior during placement in matrix rock and fractures, (2) determining the persistence of permeability reduction after gel placement, and (3) developing methods to design production well treatments to control water production. The work focused on the gel system composed of polyacrylamide and chromium acetate. The molar mass of the polymer was about six million. Chromium(III) acetate reacted and formed crosslinks between polymer molecules. The crosslinked polymer molecules, or pre-gel aggregates, combine and grow to eventually form a 3-dimensional gel. A fundamental study to characterize the formation and growth of pre-gel aggregates was conducted. Two methods, flow field-flow fractionation (FFFF) and multi-angle laser light scattering (MALLS) were used. Studies using FFFF were inconclusive. Data taken using MALLS showed that at the gel time the average molar mass of gel aggregates increased by a factor of about three while the average size increase was approximately 50%. Increased acetate concentration in the gelant increases the gel time. The in situ performance of an added-acetate system was investigated to determine the applicability for in-depth treatments. Increased acetate concentrations delayed the development of increased flow resistance during gelant injection in short sandpacks. The development of increased flow resistance (in situ gelation) was extended from 2 to 34 days by increasing the acetate-to-chromium ratio from 38 to 153. In situ gelation occurred at a time that was approximately 22% of the bulk gelation time. When carbonate rocks are treated with gel, chromium retention in the rock may limit in

Organic geochemistry investigations of crude oils from Bayoot oilfield in the Masila Basin, east Yemen and their implication for origin of organic matter and source-related type

Directory of Open Access Journals (Sweden)

Mohammed Hail Hakimi

2018-03-01

Full Text Available Thirteen crude oil samples from fractured basement reservoir rocks in the Bayoot oilfield, Masila Basin were studied to describe oil characteristics and to provide information on the source of organic matter input and the genetic link between oils and their potential source rock in the basin. The bulk geochemical results of whole oil and gasoline hydrocarbons indicate that the Bayoot oils are normal crude oil, with high hydrocarbons of more than 60%. The hydrocarbons are dominated by normal, branched and cyclic alkanes a substantial of the light aromatic compounds, suggesting aliphatic oil-prone kerogen. The high abundant of normal, branched and cyclic alkanes also indicate that the Bayoot oils are not biodegradation oils.The biomarker distributions of isoprenoid, hopane, aromatic and sterane and their cross and triangular plots suggest that the Bayoot oils are grouped into one genetic family and were generated from marine clay-rich source rock that received mixed organic matter and deposited under suboxic conditions. The biomarker distributions of the Bayoot oils are consistent with those of the Late Jurassic Madbi source rock in the basin. Biomarker maturity and oil compositions data also indicate that the Bayoot oils were generated from mature source rock with peak oil-window maturity. Keywords: Crude oil, Basement reservoir rocks, Biomarker, Organic source input, Bayoot oilfield, Masila Basin

Organic maturation levels, thermal history and hydrocarbon source rock potential of the Namurian rocks of the Clare Basin, Ireland

Energy Technology Data Exchange (ETDEWEB)

Goodhue, Robbie; Clayton, Geoffrey [Trinity Coll., Dept. of Geology, Dublin (Ireland)

1999-11-01

Vitrinite reflectance data from two inland cored boreholes confirm high maturation levels throughout the onshore part of the Irish Clare Basin and suggest erosion of 2 to 4 km of late Carboniferous cover and elevated palaeogeothermal gradients in the Carboniferous section. The observed maturation gradients are fully consistent with the published hypothesis of a late Carboniferous/Permian 'superplume' beneath Pangaea but local vertical reversals in gradients also suggest a complex thermal regime probably involving advective heating. The uppermost Visean--lower Namurian Clare Shale is laterally extensive and up to 300 m thick. Although this unit is post-mature, TOC values of up to 15% suggest that it could have considerable hydrocarbon source rock potential in any less mature offshore parts of the basin. (Author)

Estimating thermal maturity in the Eagle Ford Shale petroleum system using gas gravity data

Science.gov (United States)

Birdwell, Justin E.; Kinney, Scott A.

2017-01-01

Basin-wide datasets that provide information on the geochemical properties of petroleum systems, such as source rock quality, product composition, and thermal maturity, are often difficult to come by or assemble from publically available data. When published studies are available and include these kinds of properties, they generally have few sampling locations and limited numbers and types of analyses. Therefore, production-related data and engineering parameters can provide useful proxies for geochemical properties that are often widely available across a play and in some states are reported in publically available or commercial databases. Gas-oil ratios (GOR) can be calculated from instantaneous or cumulative production data and can be related to the source rock geochemical properties like kerogen type (Lewan and Henry, 1999) and thermal maturity (Tian et al., 2013; U.S. Energy Information Administration [EIA], 2014). Oil density or specific gravity (SG), often reported in American Petroleum Institute units (°API = 141.5 /SG – 131.5), can also provide information on source rock thermal maturity, particularly when combined with GOR values in unconventional petroleum systems (Nesheim, 2017).

Enhanced Oil Recovery from Oil-wet Carbonate Rock by Spontaneous Imbibition of Aqueous Surfactant Solutions

Energy Technology Data Exchange (ETDEWEB)

Standnes, Dag Chun

2001-09-01

The main theme of this thesis is an experimental investigation of spontaneous imbibition (SI) of aqueous cationic surfactant solution into oil-wet carbonate (chalk- and dolomite cores). The static imbibition process is believed to represent the matrix flow of oil and water in a fractured reservoir. It was known that aqueous solution of C{sub 12}-N(CH{sub 3}){sub 3}Br (C12TAB) was able to imbibe spontaneously into nearly oil-wet chalk material, but the underlying mechanism was not understood. The present work was therefore initiated, with the following objectives: (1) Put forward a hypothesis for the chemical mechanism underlying the SI of C12TAB solutions into oil-wet chalk material based on experimental data and (2) Perform screening tests of low-cost commercially available surfactants for their ability to displace oil by SI of water into oil-wet carbonate rock material. It is essential for optimal use of the surfactant in field application to have detailed knowledge about the mechanism underlying the SI process. The thesis also discusses some preliminary experimental results and suggests mechanisms for enhanced oil recovery from oil-wet carbonate rock induced by supply of thermal energy.

Depositional environment and source rock potential of Cenomanian and Turonian sedimentary rocks of the Tarfaya Basin, Southwest Morocco

Energy Technology Data Exchange (ETDEWEB)

Ghassal, B.I.; Littke, R.; Sachse, V.; Sindern, S.; Schwarzbauer, J.

2016-07-01

Detailed organic and inorganic geochemical analyses were used to assess the depositional environment and source rock potential of the Cenomanian and Turonian oil shale deposits in the Tarfaya Basin. This study is based on core samples from the Tarfaya Sondage-4 well that penetrated over 300m of Mid Cretaceous organic matter-rich deposits. A total of 242 samples were analyzed for total organic and inorganic carbon and selected samples for total sulfur and major elements as well as for organic petrology, Rock-Eval pyrolysis, Curie-Point-pyrolysis-gaschromatography-Mass-Spectrometry and molecular geochemistry of solvent extracts. Based on major elements the lower Cenomanian differs from the other intervals by higher silicate and lower carbonate contents. Moreover, the molecular geochemistry suggests anoxic bottom marine water conditions during the Cenomanian-Turonian Boundary Event (CTBE; Oceanic Anoxic Event 2: OAE2). As a proxy for the Sorg/Corg ratio, the ratio total thiophenes/total benzenes compounds was calculated from pyrolysate compositions. The results suggest that Sorg/ Corg is low in the lower Cenomanian, moderate in the upper Cenomanian, very high in the CTBE (CenomanianTuronian Boundary Event) and high in the Turonian samples. Rock-Eval data reveal that the lower Cenomanian is a moderately organic carbon-rich source rock with good potential to generate oil and gas upon thermal maturation. On the other hand, the samples from the upper Cenomanian to Turonian exhibit higher organic carbon content and can be classified as oil-prone source rocks. Based on Tmax data, all rocks are thermally immature. The microscopic investigations suggest dominance of submicroscopic organic matter in all samples and different contents of bituminite and alginite. The lower Cenomanian samples have little visible organic matter and no bituminite. The upper Cenomanian and CTBE samples are poor in bituminite and have rare visible organic matter, whereas the Turonian samples change

Increased Oil Recovery from Mature Oil Fields Using Gelled Polymer Treatments

Energy Technology Data Exchange (ETDEWEB)

Willhite, G.P.; Green, D.W.; McCool, S.

2001-03-28

Gelled polymer treatments were applied to oil reservoirs to increase oil production and to reduce water production by altering the fluid movement within the reservoir. This report is aimed at reducing barriers to the widespread use of these treatments by developing methods to predict gel behavior during placement in matrix rock and fractures, determining the persistence of permeability reduction after gel placement, and by developing methods to design production well treatments to control water production. Procedures were developed to determine the weight-average molecular weight and average size of polyacrylamide samples in aqueous solutions. Sample preparation techniques were key to achieving reproducible results.

Sedimentary environments and hydrocarbon potential of cretaceous rocks of indus basin, Pakistan

International Nuclear Information System (INIS)

Sheikh, S.A.; Naseem, S.

1999-01-01

Cretaceous rocks of Indus Basin of Pakistan are dominated by clastics with subordinate limestone towards the top. These rocks represent shelf facies and were deposited in deltaic to reducing marine conditions at variable depths. Indications of a silled basin with restricted circulation are also present. Cretaceous fine clastics/carbonates have good source and reservoir qualities. Variable geothermal gradients in different parts of basin have placed these rocks at different maturity levels; i.e. from oil to condensate and to gas. The potential of these rocks has been proved by several oil and gas discoveries particularly in the Central and Southern provinces of Indus Basin. (author)

The origin of oil in the Cretaceous succession from the South Pars Oil Layer of the Persian Gulf

Science.gov (United States)

Rahmani, Omeid; Aali, Jafar; Junin, Radzuan; Mohseni, Hassan; Padmanabhan, Eswaran; Azdarpour, Amin; Zarza, Sahar; Moayyed, Mohsen; Ghazanfari, Parviz

2013-07-01

The origin of the oil in Barremian-Hauterivian and Albian age source rock samples from two oil wells (SPO-2 and SPO-3) in the South Pars oil field has been investigated by analyzing the quantity of total organic carbon (TOC) and thermal maturity of organic matter (OM). The source rocks were found in the interval 1,000-1,044 m for the Kazhdumi Formation (Albian) and 1,157-1,230 m for the Gadvan Formation (Barremian-Hauterivian). Elemental analysis was carried out on 36 samples from the source rock candidates (Gadvan and Kazhdumi formations) of the Cretaceous succession of the South Pars Oil Layer (SPOL). This analysis indicated that the OM of the Barremian-Hauterivian and Albian samples in the SPOL was composed of kerogen Types II and II-III, respectively. The average TOC of analyzed samples is less than 1 wt%, suggesting that the Cretaceous source rocks are poor hydrocarbon (HC) producers. Thermal maturity and Ro values revealed that more than 90 % of oil samples are immature. The source of the analyzed samples taken from Gadvan and Kazhdumi formations most likely contained a content high in mixed plant and marine algal OM deposited under oxic to suboxic bottom water conditions. The Pristane/nC17 versus Phytane/nC18 diagram showed Type II-III kerogen of mixture environments for source rock samples from the SPOL. Burial history modeling indicates that at the end of the Cretaceous time, pre-Permian sediments remained immature in the Qatar Arch. Therefore, lateral migration of HC from the nearby Cretaceous source rock kitchens toward the north and south of the Qatar Arch is the most probable origin for the significant oils in the SPOL.

Evolution of sulfur speciation in bitumen through hydrous pyrolysis induced thermal maturation of Jordanian Ghareb Formation oil shale

Science.gov (United States)

Birdwell, Justin E.; Lewan, Michael; Bake, Kyle D.; Bolin, Trudy B.; Craddock, Paul R.; Forsythe, Julia C.; Pomerantz, Andrew E.

2018-01-01

Previous studies on the distribution of bulk sulfur species in bitumen before and after artificial thermal maturation using various pyrolysis methods have indicated that the quantities of reactive (sulfide, sulfoxide) and thermally stable (thiophene) sulfur moieties change following consistent trends under increasing thermal stress. These trends show that sulfur distributions change during maturation in ways that are similar to those of carbon, most clearly illustrated by the increase in aromatic sulfur (thiophenic) as a function of thermal maturity. In this study, we have examined the sulfur moiety distributions of retained bitumen from a set of pre- and post-pyrolysis rock samples in an organic sulfur-rich, calcareous oil shale from the Upper Cretaceous Ghareb Formation. Samples collected from outcrop in Jordan were subjected to hydrous pyrolysis (HP). Sulfur speciation in extracted bitumens was examined using K-edge X-ray absorption near-edge structure (XANES) spectroscopy. The most substantial changes in sulfur distribution occurred at temperatures up to the point of maximum bitumen generation (∼300 °C) as determined from comparison of the total organic carbon content for samples before and after extraction. Organic sulfide in bitumen decreased with increasing temperature at relatively low thermal stress (200–300 °C) and was not detected in extracts from rocks subjected to HP at temperatures above around 300 °C. Sulfoxide content increased between 200 and 280 °C, but decreased at higher temperatures. The concentration of thiophenic sulfur increased up to 300 °C, and remained essentially stable under increasing thermal stress (mg-S/g-bitumen basis). The ratio of stable-to-reactive+stable sulfur moieties ([thiophene/(sulfide+sulfoxide+thiophene)], T/SST) followed a sigmoidal trend with HP temperature, increasing slightly up to 240 °C, followed by a substantial increase between 240 and 320 °C, and approaching a constant value (∼0.95) at

Relative Estimation of Water Content for Flat-Type Inductive-Based Oil Palm Fruit Maturity Sensor

Directory of Open Access Journals (Sweden)

Norhisam Misron

2016-12-01

Full Text Available The paper aims to study the sensor that identifies the maturity of oil palm fruit bunches by using a flat-type inductive concept based on a resonant frequency technique. Conventionally, a human grader is used to inspect the ripeness of the oil palm fresh fruit bunch (FFB which can be inconsistent and inaccurate. There are various new methods that are proposed with the intention to grade the ripeness of the oil palm FFB, but none has taken the inductive concept. In this study, the resonance frequency of the air coil is investigated. Samples of oil palm FFB are tested with frequencies ranging from 20 Hz to 10 MHz and the results obtained show a linear relationship between the graph of the resonance frequency (MHz against time (Weeks. It is observed that the resonance frequencies obtained for Week 10 (pre-mature and Week 18 (mature are around 8.5 MHz and 9.8 MHz, respectively. These results are compared with the percentage of the moisture content. Hence, the inductive method of the oil palm fruit maturity sensor can be used to detect the change in water content for ripeness detection of the oil palm FFB.

Characteristics of waterflooding of oil pools with clay-containing reservoir rocks

Energy Technology Data Exchange (ETDEWEB)

Zheltov, Yu V; Stupochenko, V E; Khavkin, A Ya; Martos, V N

1981-01-01

When planning the development of oil fields with reservoir pressure maintenance by the injection of water or activated solutions (surfactants, alkali, etc.), it is necessary to take into account the consequences of phenomena related to clay swelling. For this purpose, it is necessary to measure on a core the parameters characterizing the change and hysteresis of the filtration and storage properties of the reservoir rocks. Swelling of the clay component of the rock along with reducing these properties in the sweep zone can promote an increase of the efficiency of displacing oil by water. Theoretical investigations showed that the maximum displacement efficiency in homogeneous clay-containing rocks does not depend on the time of starting stimulation by demineralized waters. The efficiency from changing the mineralization of the stimulating agent increases with increase of viscosity of the oil. Under certain physical and geologic conditions, a purposeful change of the filtration and storage properties by increasing or decreasing clay swelling can increase the efficiency of developing the field and can increase oil recovery.

The problem of extracting oil from bituminous rock

Energy Technology Data Exchange (ETDEWEB)

Liatifov, A.I.; Bagirov, M.K.; Shirinov, S.G.; Sokov, U.I.; Zhirnov, E.I.

1982-01-01

Results are given from experimental laboratory research on flushing bituminous sandstones using diesel or oil alkaline by-products as the flushing agent and a sodium silicate solution as the desensitization initiator for the rock.

Oils and source rocks from the Anadarko Basin: Final report, March 1, 1985-March 15, 1995

Energy Technology Data Exchange (ETDEWEB)

Philp, R. P. [School of Geology and Geophysics, Univ. of Oklahoma, Norman, OK (United States)

1996-11-01

The research project investigated various geochemical aspects of oils, suspected source rocks, and tar sands collected from the Anadarko Basin, Oklahoma. The information has been used, in general, to investigate possible sources for the oils in the basin, to study mechanisms of oil generation and migration, and characterization of depositional environments. The major thrust of the recent work involved characterization of potential source formations in the Basin in addition to the Woodford shale. The formations evaluated included the Morrow, Springer, Viola, Arbuckle, Oil Creek, and Sylvan shales. A good distribution of these samples was obtained from throughout the basin and were evaluated in terms of source potential and thermal maturity based on geochemical characteristics. The data were incorporated into a basin modelling program aimed at predicting the quantities of oil that could, potentially, have been generated from each formation. The study of crude oils was extended from our earlier work to cover a much wider area of the basin to determine the distribution of genetically-related oils, and whether or not they were derived from single or multiple sources, as well as attempting to correlate them with their suspected source formations. Recent studies in our laboratory also demonstrated the presence of high molecular weight components(C{sub 4}-C{sub 80}) in oils and waxes from drill pipes of various wells in the region. Results from such a study will have possible ramifications for enhanced oil recovery and reservoir engineering studies.

What kind of oil company do we need? Maturity and industrial structure on the Norwegian Shelf

International Nuclear Information System (INIS)

Noreng, Oeystein

1998-01-01

After many years with relatively high oil prices and moderately good oil discoveries, there is today an investment pressure on the Shelf. Many current development projects concern smaller discoveries made a long time ago. Thus the present rapid development depletes a capital of discoveries made at an early phase when the Norwegian Shelf was less mature. On this background, this presentation suggests that perhaps Norway, as a mature oil province, may not need the same kind of oil companies that dominated the petroleum activities during the development to maturity. It is experienced internationally that the various phases in the development of an oil province require different competence and thus different companies. Less oil has been found the last years than what has been produced. The command is now to find more oil. The question is how and by what company. Advantages and disadvantages are discussed for four categories of companies: (1) state companies, (2) large multinational, (3) independent, and (4) small newcomers. A section on maturing and the interest of the state as the property owner discusses the processes from large-scale operation to diversity, and maturing and the need for selective competence and low costs. Finally the paper discusses the negotiation policy of the state, political instruments and the company structure and reviews some experience from U.S.A. and UK. 1 table

Influence of infiltrated water on the change of formation water and oil permeability of crude oil bearing rocks

Energy Technology Data Exchange (ETDEWEB)

Cubric, S

1970-09-01

A brief desription is given of the causes of permeability reduction of oil-bearing rocks, due to well damage during the drilling and well completion or when working over wells. The physical properties of 2-phase flow (crude oil-water) and the possibility of increasing the existing permeability of the formation, because of the water infiltrated from the well into the crude oil layer, are described in detail. Field examples show that there are such cases, and that the artificially increased existing permeability of water-bearing rocks can be reduced and even brought to normal, if the adjacent formation zone layer is treated with surfactants (e.g., Hyflo dissolved in crude oil).

Maturity in the Styrian Basin. Maturitaet im Steirischen Tertiaerbecken

Energy Technology Data Exchange (ETDEWEB)

Sachsenhofer, R.F. (Montanuniversitaet Leoben (Austria). Inst. fuer Geowissenschaften/Geologie)

1991-01-01

The Styrian basin, situated at the south-eastern margin of the Alps, contains up to 3 km of Ottnangian to Pliocene sedimentary rocks. Main subsidence occured between Ottnangian and Sarmatian. Miocene and Plio-/Pleistocene volcanic phases can be distinguished. Maturity in the Styrian basin was studied with vitrinite reflectance curves of 25 boreholes. The oil window lies at shallow depths in the vicinty of Miocene volcanos. This is due to high heating rate during Karpatian to Lower Badenian times. Depth and thickness of the oil window increase with increasing distance from these volcanos. At a distance of some kilometers the thermal influence of this Miocene volcanism disappears. According to high recent heat flow the oil window is located below 1 500 to 2 000 m in these parts of the basin. An influence of Plio-/Pleistocene volcanism on maturity cannot be observed. (orig.).

Classes of organic molecules targeted by a methanogenic microbial consortium grown on sedimentary rocks of various maturities

Directory of Open Access Journals (Sweden)

Margaux eMesle

2015-06-01

Full Text Available Organic-rich shales are populated by methanogenic consortia that are able to degrade the fossilized organic matter into methane gas. To identify the organic fraction effectively degraded, we have sequentially depleted two types of organic-rich rocks, shales and coal, at two different maturities, by successive solvent extractions to remove the most soluble fractions (maltenes and asphaltenes and isolate kerogen. We show the ability of the consortia to produce methane from all rock samples, including those containing the most refractory organic matter, i.e. the kerogen. Shales yielded higher methane production than lignite and coal. Mature rocks yielded more methane than immature rocks. Surprisingly, the efficiency of the consortia was not influenced by the removal of the easily biodegradable fractions contained in the maltenes and asphaltenes. This suggests that one of the limitations of organic matter degradation in situ may be the accessibility of the carbon and energy source. Indeed, bitumen has a colloidal structure that may limit the accessibility to asphaltenes in the bulk rock. Solvent extractions might favor the access to asphaltenes and kerogen by modifying the spatial organization of the molecules in the rock matrix.

Changes in the sterol compositions of milk thistle oil (Silybium marianum L.) during seed maturation

Energy Technology Data Exchange (ETDEWEB)

Harrabi, S.; Curtis, S.; Hayet, F.; Mayer, P.M.

2016-07-01

In this study, the total lipid content and sterol compositions were determined during the development of milk thistle seeds. The oil content increased to a maximum value of 36±1.7% and then declined to reach a value of 30.5±0.9% at full maturity. The sterol content of milk thistle seeds was affected by the ripening degree of the seeds. At the early stages of seed maturation, Δ7 -stigmastenol was the most abundant sterol followed by β-sitosterol. However, at full maturity, β-sitosterol was the most predominant sterol (46.50±0.8%). As the seed developed, campesterol and stigmasterol amounts increased, while Δ7 -avenasterol content decreased. It can be concluded that milk thistle seed oil has a characteristic sterol pattern comparable to the ones elucidated for olive oil and corn oil. The extracted oil from milk thistle seeds is rich in phytosterols and could be used in foodpreparation and human nutrition. (Author)

An experimental and theoretical study to relate uncommon rock/fluid properties to oil recovery. Final report

Energy Technology Data Exchange (ETDEWEB)

Watson, R.

1995-07-01

Waterflooding is the most commonly used secondary oil recovery technique. One of the requirements for understanding waterflood performance is a good knowledge of the basic properties of the reservoir rocks. This study is aimed at correlating rock-pore characteristics to oil recovery from various reservoir rock types and incorporating these properties into empirical models for Predicting oil recovery. For that reason, this report deals with the analyses and interpretation of experimental data collected from core floods and correlated against measurements of absolute permeability, porosity. wettability index, mercury porosimetry properties and irreducible water saturation. The results of the radial-core the radial-core and linear-core flow investigations and the other associated experimental analyses are presented and incorporated into empirical models to improve the predictions of oil recovery resulting from waterflooding, for sandstone and limestone reservoirs. For the radial-core case, the standardized regression model selected, based on a subset of the variables, predicted oil recovery by waterflooding with a standard deviation of 7%. For the linear-core case, separate models are developed using common, uncommon and combination of both types of rock properties. It was observed that residual oil saturation and oil recovery are better predicted with the inclusion of both common and uncommon rock/fluid properties into the predictive models.

Effect of ultrasonic intensity and frequency on oil/heavy-oil recovery from different wettability rocks

Energy Technology Data Exchange (ETDEWEB)

Naderi, K.; Babadagli, T. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Alberta Univ., Edmonton, AB (Canada)

2008-10-15

This study identified the mechanisms that are responsible for additional oil recovery that is often observed following an earthquake. It focused on the theory that harmonics of low frequency waves create high frequency waves as they penetrate into rock formations. A series of experiments were conducted on oil-wet rocks with high oil viscosities. The objective was to better understand how ultrasonic energy affects oil recovery at core and pore scale. Cylindrical sandstone cores were placed in imbibition cells to examine how the presence of initial water saturation can affect recovery, and how the recovery changes for different oil viscosities. An increase in oil recovery was observed with ultrasonic energy in all cases. The additional recovery with ultrasonic energy lessened as the oil viscosity increased. Ultrasonic intensity and frequency were shown to be critical to the performance, which is important since ultrasonic waves have limited penetration into porous medium. This is a key disadvantage for commercializing this promising process for well stimulation. Therefore, the authors designed a set-up to measure the ultrasonic energy penetration capacity in different media, notably air, water and slurry. The set-up could identify which types of reservoirs are most suitable for ultrasonic application. Imbibition experiments revealed that ultrasonic radiation increases recovery, and is much more significant in oil wet cases, where initial water saturation facilitate oil recovery. Higher frequency showed a higher rate of recovery compared to lower frequency, but the ultimate recovery was not changed substantially. 46 refs., 1 tab., 16 figs.

Geochemical characteristics of crude oil from a tight oil reservoir in the Lucaogou Formation, Jimusar Sag, Junggar Basin

Science.gov (United States)

Cao, Z.

2015-12-01

Jimusar Sag, which lies in the Junggar Basin,is one of the most typical tight oil study areas in China. However, the properties and origin of the crude oil and the geochemical characteristics of the tight oil from the Lucaogou Formation have not yet been studied. In the present study, 23 crude oilsfrom the Lucaogou Formation were collected for analysis, such as physical properties, bulk composition, saturated hydrocarbon gas chromatography-mass spectrometry (GC-MS), and the calculation of various biomarker parameters. In addition,source rock evaluation and porosity permeability analysis were applied to the mudstones and siltstones. Biomarkers of suitable source rocks (TOC>1, S1+S2>6mg/g, 0.7%oil-source correlation. To analyze the hydrocarbon generation history of the Lucaogou source rock, 1D basin modeling was performed. The oil-filling history was also defined by means of basin modeling and microthermometry. The results indicated the presence of low maturity to mature crude oils originating from the burial of terrigenous organic matter beneath a saline lake in the source rocks of mainly type II1kerogen. In addition, a higher proportion of bacteria and algae was shown to contribute to the formation of crude oil in the lower section when compared with the upper section of the Lucaogou Formation. Oil-source correlations demonstrated that not all mudstones within the Lucaogou Formation contributed to oil accumulation.Crude oil from the upper and lower sections originated from thin-bedded mudstones interbedded within sweet spot sand bodies. A good coincidence of filling history and hydrocarbon generation history indicated that the Lucaogou reservoir is a typical in situ reservoir. The mudstones over or beneath the sweet spot bodies consisted of natural caprocks and prevented the vertical movement of oil by capillary forces. Despite being thicker, the thick-bedded mudstone between the upper and lower sweet spots had no obvious contribution to

Policosanol composition, antioxidant and anti-arthritic activities of milk thistle (Silybium marianum L.) oil at different seed maturity stages.

Science.gov (United States)

Harrabi, Saoussem; Ferchichi, Azza; Bacheli, Asma; Fellah, Hayet

2018-04-16

Several anti-arthritic drugs and synthetic antioxidants have wide pharmaceutical uses and are often associated with various side effects on the human health. Dietary seed oils and their minor components like policosanol may offer an effective alternative treatment for arthritic and oxidative-stress related diseases. The biological effects of seed oils were affected by different parameters such as the stage of seed maturity. Hence, this study seeks to determine the policosanol content, antioxidant and anti-arthritic activities of milk thistle (Silybium marianum L.) oil extracted at various stages of seed maturation. Milk thistle oil samples were extracted from seeds collected at three maturation stages (immature, intermediate, and mature). The 2,2-diphenyl-1-picrylhydrazyl (DPPH) and 2,2'-azino-bis (3-ethyl-benzthiazoline-6-sulfonic acid) (ABTS) radical scavenging assays were used to determine the antioxidant activity of the extracted oils. The anti-arthritic activity of oil samples was evaluated with bovine serum protein denaturation and egg albumin denaturation methods. Gas chromatography coupled to mass spectrometry (GC-MS) was employed to determine the policosanol profile. Policosanol profile, antioxidant and anti-arthritic activities of milk thistle oil were influenced by the seed maturity stages. The oil extracted from the immature seeds had the highest total policosanol content (987.68 mg/kg of oil) and displayed the maximum antiradical activity (96.42% and 90.35% for DPPH test and ABTS assay, respectively). Nine aliphatic alcohols were identified in the milk thistle oil. The dominant poliosanol in the mature seed oil was octacosanol (75.44%), while triacontanol was the major compound (40.25%) in the immature seed oil. Additionally, the maximum inhibition of bovine serum protein denaturation (92.53%) and egg albumin denaturation (86.36%) were observed in immature seed oil as compared to mature seed oil. A high correlation was found between the total

Evaluation of the nature, origin and potentiality of the subsurface Middle Jurassic and Lower Cretaceous source rocks in Melleiha G-1x well, North Western Desert, Egypt

Directory of Open Access Journals (Sweden)

Mohamed M. El Nady

2015-09-01

Full Text Available The present work aims to evaluate the nature and origin of the source rock potentiality of subsurface Middle Jurassic and Lower Cretaceous source rocks in Melleiha G-1x well. This target was achieved throughout the evaluation of total organic carbon, rock Eval pyrolysis and vitrinite reflectance for fifteen cutting samples and three extract samples collected from Khatatba, Alam El Bueib and Kharita formations in the studied well. The result revealed that the main hydrocarbon of source rocks, for the Middle Jurassic (Khatatba Fm. is mainly mature, and has good capability of producing oil and minor gas. Lower Cretaceous source rocks (Alam El Bueib Fm. are mature, derived from mixed organic sources and have fair to good capability to generate gas and oil. Kharita Formation of immature source rocks originated from terrestrial origin and has poor to fair potential to produce gas. This indicates that Khatatba and Alam El Bueib formations take the direction of increasing maturity far away from the direction of biodegradation and can be considered as effective source potential in the Melleiha G-1x well.

Burial history influence on the generation of some Italian oils

Energy Technology Data Exchange (ETDEWEB)

Mattavelli, L.; Novelli, L. (AGIP SPA, San Donato Milanese (Italy))

1990-05-01

Many Italian oils were sourced by Triassic source rock; evidence of this exists in the Po Plain. In the Adriatic Sea, and offshore southern Sicily. Bulk and geochemical characteristics of these oils are quite dissimilar: heavy oils as well as gasolines were discovered. Such differences are partly attributable to the organic matter type and to environmental conditions, but the role of the source rock's burial histories is fundamental in determining oil characteristics. The different burial histories in these two areas definitely account for these differences. In the Po Plain, the Raethian Argilliti di Riva di Solto Formation, source rock of condensates of the Malossa area, started to generate very early as a consequence of the noticeable Rhaetian-Liassic subsidence. The generation of oil continued for a long geological time, but probably hydrocarbons were lost for the lack of traps. Only condensates, generated by the further Pliocene-Quaternary burial, were accumulated in the Neogene traps. In the western part of the Po Plain, Gaggiano and Villafortuna oils (34 and 40{degree} API), sourced by the Ladinian Meride Formation, were generated only during the sizeable Neogene-Quaternary subsidence. The high heating rate in this case probably enhanced expulsion efficiency, allowing secondary migration toward shallower depths and, consequently, preventing hydrocarbons from secondary cracking. Offshore in southern Sicily (Gela field), the recent subsidence (Pliocene-Pleistocene) is responsible for Triassic source rock maturation. In this case the shallower depth reached by the source rock and, consequently, the lower temperatures at which maturity occurred are partly responsible for the generation of heavy oils, even if other factors such as early expulsion due to tectonics and organic matter type probably play a more important role.

Restoration of Circum-Arctic Upper Jurassic source rock paleolatitude based on crude oil geochemistry

Science.gov (United States)

Peters, K.E.; Ramos, L.S.; Zumberge, J.E.; Valin, Z.C.; Scotese, C.R.

2008-01-01

Tectonic geochemical paleolatitude (TGP) models were developed to predict the paleolatitude of petroleum source rock from the geochemical composition of crude oil. The results validate studies designed to reconstruct ancient source rock depositional environments using oil chemistry and tectonic reconstruction of paleogeography from coordinates of the present day collection site. TGP models can also be used to corroborate tectonic paleolatitude in cases where the predicted paleogeography conflicts with the depositional setting predicted by the oil chemistry, or to predict paleolatitude when the present day collection locality is far removed from the source rock, as might occur due to long distance subsurface migration or transport of tarballs by ocean currents. Biomarker and stable carbon isotope ratios were measured for 496 crude oil samples inferred to originate from Upper Jurassic source rock in West Siberia, the North Sea and offshore Labrador. First, a unique, multi-tiered chemometric (multivariate statistics) decision tree was used to classify these samples into seven oil families and infer the type of organic matter, lithology and depositional environment of each organofacies of source rock [Peters, K.E., Ramos, L.S., Zumberge, J.E., Valin, Z.C., Scotese, C.R., Gautier, D.L., 2007. Circum-Arctic petroleum systems identified using decision-tree chemometrics. American Association of Petroleum Geologists Bulletin 91, 877-913]. Second, present day geographic locations for each sample were used to restore the tectonic paleolatitude of the source rock during Late Jurassic time (???150 Ma). Third, partial least squares regression (PLSR) was used to construct linear TGP models that relate tectonic and geochemical paleolatitude, where the latter is based on 19 source-related biomarker and isotope ratios for each oil family. The TGP models were calibrated using 70% of the samples in each family and the remaining 30% of samples were used for model validation. Positive

Production Costs of Alternative Transportation Fuels. Influence of Crude Oil Price and Technology Maturity

Energy Technology Data Exchange (ETDEWEB)

Cazzola, Pierpaolo; Morrison, Geoff; Kaneko, Hiroyuki; Cuenot, Francois; Ghandi, Abbas; Fulton, Lewis

2013-07-01

This study examines the production costs of a range of transport fuels and energy carriers under varying crude oil price assumptions and technology market maturation levels. An engineering ''bottom-up'' approach is used to estimate the effect of the input cost of oil and of various technological assumptions on the finished price of these fuels. In total, the production costs of 20 fuels are examined for crude oil prices between USD 60 and USD 150 per barrel. Some fuel pathways can be competitive with oil as their production, transport and storage technology matures, and as oil price increases. Rising oil prices will offer new opportunities to switch to alternative fuels for transport, to diversify the energy mix of the transport sector, and to reduce the exposure of the whole system to price volatility and potential distuption of supply. In a time of uncertainty about the leading vehicle technology to decarbonize the transport sector, looking at the fuel cost brings key information to be considered to keep mobility affordable yet sustainable.

Hydrodynamic thickness of petroleum oil adsorbed layers in the pores of reservoir rocks.

Science.gov (United States)

Alkafeef, Saad F; Algharaib, Meshal K; Alajmi, Abdullah F

2006-06-01

The hydrodynamic thickness delta of adsorbed petroleum (crude) oil layers into the pores of sandstone rocks, through which the liquid flows, has been studied by Poiseuille's flow law and the evolution of (electrical) streaming current. The adsorption of petroleum oil is accompanied by a numerical reduction in the (negative) surface potential of the pore walls, eventually stabilizing at a small positive potential, attributed to the oil macromolecules themselves. After increasing to around 30% of the pore radius, the adsorbed layer thickness delta stopped growing either with time or with concentrations of asphaltene in the flowing liquid. The adsorption thickness is confirmed with the blockage value of the rock pores' area determined by the combination of streaming current and streaming potential measurements. This behavior is attributed to the effect on the disjoining pressure across the adsorbed layer, as described by Derjaguin and Churaev, of which the polymolecular adsorption films lose their stability long before their thickness has approached the radius of the rock pore.

Wettability of Oil-Producing Reservoir Rocks as Determined from X-ray Photoelectron Spectroscopy

Science.gov (United States)

Toledo; Araujo; Leon

1996-11-10

Wettability has a dominant effect in oil recovery by waterflooding and in many other processes of industrial and environmental interest. Recently, the suggestion has been made that surface science analytical techniques (SSAT) could be used to rapidly determine the wettability of reservoir materials. Here, we bring the capability of X-ray photoelectron spectroscopy (XPS) to bear on the wettability evaluation of producing reservoir rocks. For a suite of freshly exposed fracture surfaces of rocks we investigate the relationship between wettability and surface composition as determined from XPS. The classical wettability index as measured with the Amott-Harvey test is used here as an indicator of the wettability of natural sandstones. The XPS spectra of oil-wet surfaces of rocks reveal the existence of organic carbon and also of an "organic" silicon species, of the kind Si-CH relevant to silanes, having a well-defined binding energy which differs from that of the Si-O species of mineral grains. We provide quantifiable evidence that chemisorbed organic material on the pore surfaces defines the oil-wetting character of various reservoir sandstones studied here which on a mineralogic basis are expected to be water-wet. This view is supported by a strong correlation between C content of pore surfaces and rock wettability. The results also suggest a correlation between organic silicon content on the pore surfaces and rock hydrophobicity.

Bazhen Fm matured reservoir evaluation (West Siberia, Russia)

Science.gov (United States)

Parnachev, S.; Skripkin, A.; Baranov, V.; Zakharov, S.

2015-02-01

The depletion of the traditional sources of hydrocarbons leads to the situation when the biggest players of the oil and gas production market turn to unconventional reserves. Commercial shale oil and gas production levels in the USA have largely determined world prospects for oil and gas industry development. Russia takes one of the leading place in the world in terms of shale oil resources. The main source rock of the West Siberia, the biggest oil and gas basin in Russia under development, the Bazhen Fm and its stratigraphic and lithologic analogs, is located in the territory of over 1,000,000 square kilometers. Provided it has similar key properties (organic carbon content, porosity, permeability) with the deposits of the Bakken Fm and Green River Fm, USA, it is still extremely poorly described with laboratory methods. We have performed the laboratory analysis of core samples from a well drilled in Bazhen Fm deposits with matured organic matter (Tmax>435 °C). It was demonstrated the applicability of the improved steady-state gas flow method to evaluate the permeability of nanopermeable rocks. The role of natural fracturing in forming voids was determided that allows regarding potential Bazhen Fm reservoirs as systems with dual porosity and dual permeability.

Bazhen Fm matured reservoir evaluation (West Siberia, Russia)

International Nuclear Information System (INIS)

Parnachev, S; Skripkin, A; Baranov, V; Zakharov, S

2015-01-01

The depletion of the traditional sources of hydrocarbons leads to the situation when the biggest players of the oil and gas production market turn to unconventional reserves. Commercial shale oil and gas production levels in the USA have largely determined world prospects for oil and gas industry development. Russia takes one of the leading place in the world in terms of shale oil resources. The main source rock of the West Siberia, the biggest oil and gas basin in Russia under development, the Bazhen Fm and its stratigraphic and lithologic analogs, is located in the territory of over 1,000,000 square kilometers. Provided it has similar key properties (organic carbon content, porosity, permeability) with the deposits of the Bakken Fm and Green River Fm, USA, it is still extremely poorly described with laboratory methods. We have performed the laboratory analysis of core samples from a well drilled in Bazhen Fm deposits with matured organic matter (T max >435 °C). It was demonstrated the applicability of the improved steady-state gas flow method to evaluate the permeability of nanopermeable rocks. The role of natural fracturing in forming voids was determided that allows regarding potential Bazhen Fm reservoirs as systems with dual porosity and dual permeability

Evaluation on occluded hydrocarbon in deep–ultra deep ancient source rocks and its cracked gas resources

Directory of Open Access Journals (Sweden)

Jian Li

2015-12-01

Full Text Available Oil-cracked gas, as the main type of high-over mature marine natural gas in China, is mainly derived from occluded hydrocarbon. So it is significant to carry out quantitative study on occluded hydrocarbon. In this paper, the occluded hydrocarbon volume of the main basins in China was calculated depending on their types, abundances and evolution stages by means of the forward method (experimental simulation and the inversion method (geologic profile dissection. And then, occluded hydrocarbon evolution models were established for five types of source rocks (sapropelic, sapropelic prone hybrid, humic prone hybrid, humic and coal. It is shown that the hydrocarbon expulsion efficiency of sapropelic and sapropelic prone hybrid excellent source rocks is lower than 30% at the low-maturity stage, 30%–60% at the principal oil generation stage, and 50%–80% at the high-maturity stage, which are all about 10% higher than that of humic prone hybrid and humic source rocks at the corresponding stages. The resource distribution and cracked gas expulsion of occluded hydrocarbon since the high-maturity stage of marine source rocks in the Sichuan Basin were preliminarily calculated on the basis of the evolution models. The cracked gas expulsion is 230.4 × 1012 m3 at the high evolution stage of occluded hydrocarbon of the Lower Cambrian Qiongzhusi Fm in this basin, and 12.3 × 1012 m3 from the source rocks of Sinian Doushantuo Fm, indicating good potential for natural gas resources. It is indicated that the favorable areas of occluded hydrocarbon cracked gas in the Qiongzhusi Fm source rocks in the Sichuan Basin include Gaoshiti–Moxi, Ziyang and Weiyuan, covering a favorable area of 4.3 × 104 km2.

Qualitative and quantitative analysis of Dibenzofuran, Alkyldibenzofurans, and Benzo[b]naphthofurans in crude oils and source rock extracts

Science.gov (United States)

Meijun Li,; Ellis, Geoffrey S.

2015-01-01

Dibenzofuran (DBF), its alkylated homologues, and benzo[b]naphthofurans (BNFs) are common oxygen-heterocyclic aromatic compounds in crude oils and source rock extracts. A series of positional isomers of alkyldibenzofuran and benzo[b]naphthofuran were identified in mass chromatograms by comparison with internal standards and standard retention indices. The response factors of dibenzofuran in relation to internal standards were obtained by gas chromatography-mass spectrometry analyses of a set of mixed solutions with different concentration ratios. Perdeuterated dibenzofuran and dibenzothiophene are optimal internal standards for quantitative analyses of furan compounds in crude oils and source rock extracts. The average concentration of the total DBFs in oils derived from siliciclastic lacustrine rock extracts from the Beibuwan Basin, South China Sea, was 518 μg/g, which is about 5 times that observed in the oils from carbonate source rocks in the Tarim Basin, Northwest China. The BNFs occur ubiquitously in source rock extracts and related oils of various origins. The results of this work suggest that the relative abundance of benzo[b]naphthofuran isomers, that is, the benzo[b]naphtho[2,1-d]furan/{benzo[b]naphtho[2,1-d]furan + benzo[b]naphtho[1,2-d]furan} ratio, may be a potential molecular geochemical parameter to indicate oil migration pathways and distances.

Hydrocarbon Maturation and Os Mixing on Bolide Impact at the Frasnian-Famennian Boundary

Science.gov (United States)

Stein, H.; Zimmerman, A.; Yang, G.; Hannah, J.; Egenhoff, S.

2009-04-01

An intractable problem in the application of Re-Os geochemistry has been knowledge of the distribution of Re and Os between source rock and generated hydrocarbon. Solutions lie in combined experimental work with controlled and induced maturation, and field studies optimized by known source rock and time of hydrocarbon generation. The Siljan impact site with its variably tilted but largely intact Ordovician-Silurian sections provides an unsurpassed opportunity to examine the Re-Os systematics of source rock and generated crude oil, and the Re-Os imprint of the bolide. This three-component system contains (1) a time pin for maturation (377 ± 2 Ma; laser argon dating of impact melt, Reimold et al. 2005) arguably at the Frasnian-Famennian boundary, (2) known source rocks with kerogens still intact, and (3) crude oils generated on impact. Modeling takes into consideration the possibility of pre-impact maturation as well. At Siljan, numerous quarries expose the Upper Ordovician Boda and Kullsberg limestone mounds, and locally, the underlying and laterally equivalent Tretaspis (Fjäcka) shale. We obtained a sample of crude oil seeping from a drill hole in the quarry floor at Solberga. Preliminary Re-Os analyses on four aliquots of this oil form an excellent linear array in 187Re/188Os versus 187Os/188Os space. The associated age, however, is impossibly old (Neoproterozoic), and the initial 187Os/188Os unreasonably low (0.2). Rather, this linear array fits a mixing line between a meteoritic component and a hydrocarbon generated from the Tretaspis shale. We are presently performing further tests to isolate the two end-members. Filtering suggests that the extraterrestrial component consists of small physical particles which can be largely removed from the petroleum fraction. The extreme contrast in Re-Os composition between meteorite (known) and black shale (in progress) end-members maximizes the sensitivity of the isotopic study. Reimold, W.U., Kelley, S.P., Sherlock, S

Interpretation of Oil Seepage of Source Rock Based Magnetic Survey in Cipari Cilacap District

Directory of Open Access Journals (Sweden)

Sukmaji Anom Raharjo

2015-12-01

Full Text Available The magnetic survey had been conducted in Village of Cipari, District of Cipari, Region of  Cilacap to interpret to the location of the oil seepage source rock. Boundary of the research area is 108.75675°E – 108.77611°E and 7.42319°S – 7.43761°S. The observed total magnetic data is corrected and reducted to obtain the local magnetic anomaly data. The local magnetic anomaly data is applied to model the subsurface bodies anomalies based on the Mag2DC for Windows software. With be supported the geological information, the some bodies anomalies are interpreted as the basaltic igneous rock (c = 0.0051, the alternately of sandstone and claystone and insert of marl from Halang Formation (c = 0.0014, the breccia from Kumbang Formation (c = 0.0035, the alternately of sandstones and claystone with insert of marl and breccia from Halang Formation (c = 0.0036, the claystone from Tapak Formation (c = 0.0015, the alternately of sandstones and claystone with insert of marl and compacted breccia from Halang Formation (c = 0.0030, and the alternately of sandstone and claystone from   Halang Formation (c = 0.0020. The plantonic foraminifer fossils as resources of oil seepage are estimated in the sedimentaries rocks, where the oil flows from those rocks into the         reservoir (source rock. Based on the interpretation results, the source rock is above basaltic igneous rock with the approximate position is 108.76164°W and 7.43089°S; and the depth is 132.09 meters below the average topographic.

An organic geochemical correlation study of some Drmno depresssion crude oils (southern part of the Pannonian Basin, Yugoslavia

Directory of Open Access Journals (Sweden)

D. VITOROVIC

2001-05-01

Full Text Available The results of an investigation of crude oils originating from the Sirakovo and Bradarac-Maljurevac localities (southern part of the Pannonian Basin are reported in this paper. The aim was to estimate the organic geochemical similarity of the crude oils from the Drmno (Kostolac depression oil fields. The nine selected samples originated from reservoir rocks of various depths. Reliable source and organic geochemical maturation parameters served as the basis for the correlation studies. The similar origin of the investigated Drmno depression crude oils was corroborated, characterized by a significant participation of terrestrial precursor biomass. They were shown to be of relatively low maturity and to have been formed during the earlier stages of the diagenet- ic-catagenetic sequence of processes leading to the formation of crude oils, most probably in source rocks ofTertiary age, corresponding to vitrinite reflectances between Ro = 0.70 % and Ro = 0.80 %. The crude oils from Bradarac-Maljurevac seemed to be somewhat less homogeneous with respect to organic geochemical parameters compared to Sirakovo crude oils.

Diffusion and spatially resolved NMR in Berea and Venezuelan oil reservoir rocks.

Science.gov (United States)

Murgich, J; Corti, M; Pavesi, L; Voltini, F

1992-01-01

Conventional and spatially resolved proton NMR and relaxation measurements are used in order to study the molecular motions and the equilibrium and nonequilibrium diffusion of oils in Berea sandstone and Venezuelan reservoir rocks. In the water-saturated Berea a single line with T*2 congruent to 150 microseconds is observed, while the relaxation recovery is multiexponential. In an oil reservoir rock (Ful 13) a single narrow line is present while a distribution of relaxation rates is evidenced from the recovery plots. On the contrary, in the Ful 7 sample (extracted at a deeper depth in a different zone) two NMR components are present, with 3.5 and 30 KHz linewidths, and the recovery plot exhibits biexponential law. No echo signal could be reconstructed in the oil reservoir rocks. These findings can be related to the effects in the micropores, where motions at very low frequency can occur in a thin layer. From a comparison of the diffusion constant in water-saturated Berea, D congruent to 5*10(-6) cm2/sec, with the ones in model systems, the average size of the pores is estimated around 40 A. The density profiles at the equilibrium show uniform distribution of oils or of water, and the relaxation rates appear independent from the selected slice. The nonequilibrium diffusion was studied as a function of time in a Berea cylinder with z axis along H0, starting from a thin layer of oil at the base, and detecting the spin density profiles d(z,t) with slice-selection techniques. Simultaneously, the values of T1's were measured locally, and the distribution of the relaxation rates was observed to be present in any slice.(ABSTRACT TRUNCATED AT 250 WORDS)

Organic geochemistry of oil and gas in the Kuqa depression, Tarim Basin, NW China

Energy Technology Data Exchange (ETDEWEB)

Digang Liang; Shuichang Zhang; Jianping Chen [China National Petroleum Corporation, Beijing (China). Key Laboratory for Petroleum Geochemistry; Research Institute of Petroleum Exploration and Development, PetroChina, Beijing (China); Feiyu Wang [China National Petroleum Corporation, Beijing (China). Key Laboratory for Petroleum Geochemistry; Peirong Wang [China National Petroleum Corporation, Beijing (China). Key Laboratory for Petroleum Geochemistry; Jianghan Petroleum Institute (China)

2003-07-01

The Kuqa depression in the Tarim Basin, NW China contains significant natural gas and condensate resources, with only small amounts of black oil. This study demonstrates that the primary reason for the accumulation of large natural gas reserves in the Kuqa depression is the high maturity level of the Jurassic coal-bearing sequence that is currently at the peak stage of dry gas generation. From the combined stable carbon isotopes and molecular and biomarker data it is possible to identify two separate source rocks for the discovered hydrocarbon fluids: the gases were primarily from the Middle-Lower Jurassic coals and associated clastic rocks, and the oils were from the Upper Triassic lacustrine mudstones. Peak oil generation from the Triassic source rocks occurred during the early Miocene (23-12 Ma b.p.). These oils migrated laterally over relatively long distances ({approx}20-50 km) reaching the outer periphery of the depression. Peak gas generation took place more recently, perhaps during the past 5 Ma. The gases migrated mainly along faults over relatively short lateral distances, resulting in accumulations adjacent to the over-matured source kitchens. Different timings for the trap formation along the north and south margins and a late injection of gas into early oil accumulations provided favorable conditions for the formation of evaporative condensates and the preservation of gas pools in the more down-dip reservoirs and oil pools in the more up-dip locations. (author)

Hydrodynamism, crude oil distribution and geochemistry of the stratigraphic column in a transect of the Eastern Venezuelan Basin

Energy Technology Data Exchange (ETDEWEB)

Gallango, O.; Escandon, M.; Alberdi, M. (Intevep, S.A. Caracas (Venezuela)); Parnaud, F.; Pascual, J.C. (Beicip, Rueil Malmaison (France))

1992-01-01

The hydrocarbon accumulation history in a transect of the Eastern Venezuelan Basin is closely related to the generation and migration process as a consequence of the stratigraphic, structural and tectonic evolution of the basin during the Cretaceous and Cenozoic times. Thermal maturity assessment based on kinetic parameters using the appropriate software indicates that the generation of oil from the marine facies of the Querecual and San Antonio source rocks in the northern part of the basin took place during early Paleocene to early Miocene times prior to the start of thrusting, while the second and third phase occurred during middle Miocene to recent times in zones beneath the principal thrust in the Maturing area. The third phase of oil generation is associated with the latter thrusts which are out of sequence. Taking into consideration the development of the oil and gas kitchen through time, the hydrodynamism, the characteristics and distribution of the hydrocarbons, the migration of oil and gas have been outlined. The major differences observed among the oils, are due to maturity and post-accumulation processes such as oil mixing and biodegradation. A wide range of thermal maturity was observed in the oils, which is mainly due to the thermal stress experienced by the source rock. Association of light crudes with meteoric waters have been observed, as well as heavy to extra-heavy crudes with connate waters at greater depth. These unusual associations of crudes and formation waters are related to the hydrodynamical regime in the basin.

Primary migration of Jurassic coal-derived oil in Santanghu basin

Energy Technology Data Exchange (ETDEWEB)

Zhang, W.; Zhong, N.; Ren, D. [China University of Mining and Technology, Beijing (China). Dept of Resource Exploitation Engineering

2000-11-01

It is known that the differential evolution of the multiple macerals results in 'oil generation by stage', and that 'early generation, early expulsion' is one of the preconditions for the efficient accumulation of the coal-derived oil. Based upon the study on the evolution of the physical properties, related to the hydrocarbon expulsion, of the Jurassic organic rock in Santanghu basin during the course of maturation, the mechanism of the primary migration of its coal-derived oil was discussed. The rapid loss of the inherent moisture in the organic rock was not accordant with the main generation stage of the coal-derived oil, so it was unrealistic that the oil migrated by dissolution in the expelled water. It is thought that the special forming mechanism of the continuous 'bitumen network' under the condition of over-pressure and an earlier history of primary migration may be essential to the Jurassic coal-derived oil in Santanghu basin. 17 refs., 4 figs.

Planning for maturity: Royalty changes for Alberta's conventional oil and gas production

International Nuclear Information System (INIS)

Ekelund, M.W.

1993-01-01

An overview is presented of the royalty regime in the Alberta petroleum industry. Current oil and natural gas policy reviews, royalty regime response to fluctuating prices and expectations, maturing of the oil basin, and the economic state of the industry are discussed. With low or negative returns, there is little incentive to invest in the industry. A reduction of royalty on existing pools would provide cash flow for new activity and would raise current return on equity and capital. The province of Alberta has reduced royalties on oil and gas discovered after 1973, with an expected value of reduction of $85 million of gross royalties for each. The net cost to the Crown will be $85 million for oil and ca 25% less for gas due to a drop in processing costs. The royalty collection system will also be simplified. These changes are expected to result in increased levels of oil well drilling and reactivation. 6 figs., 2 tabs

Petroleum Systems and Assessment of Undiscovered Oil and Gas in the Raton Basin - Sierra Grande Uplift Province, Colorado and New Mexico - USGS Province 41

Science.gov (United States)

Higley, Debra K.

2007-01-01

Introduction The purpose of the U.S. Geological Survey's (USGS) National Oil and Gas Assessment is to develop geologically based hypotheses regarding the potential for additions to oil and gas reserves in priority areas of the United States. The USGS recently completed an assessment of undiscovered oil and gas resources of the Raton Basin-Sierra Grande Uplift Province of southeastern Colorado and northeastern New Mexico (USGS Province 41). The Cretaceous Vermejo Formation and Cretaceous-Tertiary Raton Formation have production and undiscovered resources of coalbed methane. Other formations in the province exhibit potential for gas resources and limited production. This assessment is based on geologic principles and uses the total petroleum system concept. The geologic elements of a total petroleum system include hydrocarbon source rocks (source rock maturation, hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). The USGS used this geologic framework to define two total petroleum systems and five assessment units. All five assessment units were quantitatively assessed for undiscovered gas resources. Oil resources were not assessed because of the limited potential due to levels of thermal maturity of petroleum source rocks.

Geochemistry of coal-measure source rocks and natural gases in deep formations in Songliao Basin, NE China

Energy Technology Data Exchange (ETDEWEB)

Mi, Jingkui; Zhang, Shuichang; Hu, Guoyi; He, Kun [State Key Laboratory for Enhanced Oil Recovery, Beijing (China); Petroleum Geology Research and Laboratory Center, Research Institute of Petroleum Exploration and Development, PetroChina (China); Key Laboratory for Petroleum Geochemistry, China National Petroleum Corp. (China)

2010-12-01

The natural gases developed in deep volcanic rock reservoirs of the Songliao Basin, NE China are characterized by enriched {delta}{sup 13}C value for methane and frequently reversal carbon isotopic distribution pattern. Although many researchers consider such gas type as an abiogenic origin, we believe the natural gases have a biogenic origin mainly except little inorganic gases and the reversal carbon isotopic distribution pattern of gases is caused by mixing of different origin gases. Methane carbon isotopic values for majority samples fall in the range from - 24 permille to - 32 permille, which is heavier than typical coal-type gases in other Chinese basins. There are several reasons caused heavy carbon isotope of methane: (1) Carbon isotopic values of source kerogen are 3-5 permille heavier than these from other basins; (2) Source rocks are at extremely high maturity stage with vitrinite reflectance mostly above 3.0%; (3) Portion of gas is derived from basement mudrock or slate with higher maturity. The observation on the organic from deep formation reveals that there is a relatively high content for liptinite, which reaches approximately 8 to 10%. The macerals component of source rock shows that the source rocks have some ability to generate oil. Small portion of oil was generated from high hydrogen content macerals in coals and shales as proof by oil found in microcrack and in micropore of coal and oil-bearing fluid inclusions grown in volcanic reservoir. The occurrence of pyrobitumen in volcanic reservoir indicates preexisted oil had been cracked into wet gas, and this kind of gas had also been found in gas pools. Heavy isotopic methane is derived from coal at extremely high maturity stage. There may be little inorganic alkane gases in deep layers for their geochemistry and special geological setting of Songliao Basin. Artificial mixing experiments of different origins gases confirm that inorganic gas such as gas from well FS1 mixed with other end members

Thermal maturity history and implications for hydrocarbon exploration in the Catatumbo basin, Colombia

International Nuclear Information System (INIS)

Rangel, Antonio; Hernandez, Roberto

2007-01-01

A thermal model integrated with oil and gas geochemical study has been constructed for the Catatumbo basin, Colombia for provides petroleum system data for hydrocarbon exploration. The calibration of the thermal model with maturity data took into account a changing heat flow scheme which included a thermal increase towards the end of the Jurassic and another one in the early Eocene, associated with rifting events. Locally, active/generating source rocks are within the synclines axes. The hydrocarbon expulsion time for Cretaceous source rocks (Capacho and La Luna formations) started in the upper Paleocene-Eocene, while for the los Cuervos Formation the generation and expulsion started of 1 0 my. The petroleum expelled during the Paleocene-Miocene, were likely accumulated in structures formed since the end of the cretaceous, while the younger structures that resulted from the Andean orogen were charged by remigration from the older structures and additionally with the youngest lately generated hydrocarbons. The accumulations of hydrocarbons are mainly the result of generation and migration locally within the basin. The Catatumbo Basin contains thermogenic wet gases with different degrees of thermal maturity which varies from around 1,0 for 2,5 equivalent Ro. The highest degree of thermal evolution according to maturity indicators and thermal modeling is in the southern area, which is prospective for wet gas. The central and northern area appears more prospective for oil with minor amounts of gas

Characteristics of the Triassic Source Rocks of the Aitutu Formation in the (West Timor Basin

Directory of Open Access Journals (Sweden)

Asep Kurnia Permana

2014-12-01

Full Text Available DOI:10.17014/ijog.v1i3.192The Triassic rocks of the (West Timor Basin have been identified that was mainly deposited in the  marine environment. The fine grained clastics and carbonate  rocks of this Triassic marine  facies are considered to be the most promising source rocks potential in this basin. In this paper we present geochemical and petrographic data from outcrop samples of the Triassic carbonate Aitutu Formation, due to emphasized the organic maturation, kerogen type of the organic matter and the origin of the organic matter.  A representative of selected sample were subjected to the Rock-Eval Pyrolisis, vitrinite reflectance and thermal alteration index, bitumen extraction, were analyzed on the GC-MS. The samples were collected from marine deposit of the Triassic Sequence. The TOC values of the analyzed sample range between rich and rich organic richness (0.51% - 9.16%, wt.%, TOC, which consists mainly of type II and III kerogen and the organic matter consider to be predominantly oil/gas prone and gas prone potential. The thermal maturity assessed from Tmax, TAI, and vitrinite reflectance shows an immature to early peak mature stage of the organic matter. The GC-MS analyses of the biomarkers indicate mainly the organic matter derived from mixed source rocks facies containing alga debris and higher plant terrestrial origin.

Buriti oil (Mauritia flexuosa L.) negatively impacts somatic growth and reflex maturation and increases retinol deposition in young rats.

Science.gov (United States)

Medeiros, Maria C; Aquino, Jailane S; Soares, Juliana; Figueiroa, Edigleide B; Mesquita, Hanni M; Pessoa, Debora C; Stamford, Tania M

2015-11-01

Buriti oil contains nutrients such as essential fatty acids and vitamins, which are directly involved with neonates' development. However, the refining process of this oil can change its nutrient profile. This study investigated the effects of maternal consumption of Buriti oil (crude or refined), on reflex and somatic development and retinol levels in neonatal rats. Thirty-six Wistar male neonate rats born from mothers who consumed diet with 7% lipids during gestation and lactation were used. Rats were randomized into three groups: rats receiving diet added of soybean oil (control-CG), crude Buriti oil (CB) and refined Buriti oil (RB). Offspring weight, tail length, reflex ontogeny and somatic maturation were assessed during lactation. At the end of the experiment, serum and liver retinol concentrations were measured. Animals from CB and RB groups showed delayed onset of palm grasp, righting reflex and cliff avoidance reflexes compared to the control group (CG). However, animals from RB group showed anticipation of auditory startle compared to those from BC group. Regarding somatic maturation indicators, animals from RB group showed delayed eye opening and eruption of superior and inferior incisors in relation to control and anticipation in the auditory conduit opening in relation to CB group. Rats from CB and RB groups showed higher serum and liver vitamin A contents. Buriti oil delays physical parameters and reflex maturation and increases serum and liver retinol deposition among neonatal rats. Copyright © 2015. Published by Elsevier Ltd.

Executive Summary -- assessment of undiscovered oil and gas resources of the San Joaquin Basin Province of California, 2003: Chapter 1 in Petroleum systems and geologic assessment of oil and gas in the San Joaquin Basin Province, California

Science.gov (United States)

Gautier, Donald L.; Scheirer, Allegra Hosford; Tennyson, Marilyn E.; Peters, Kenneth E.; Magoon, Leslie B.; Lillis, Paul G.; Charpentier, Ronald R.; Cook, Troy A.; French, Christopher D.; Klett, Timothy R.; Pollastro, Richard M.; Schenk, Christopher J.

2007-01-01

In 2003, the U.S. Geological Survey (USGS) completed an assessment of the oil and gas resource potential of the San Joaquin Basin Province of California (fig. 1.1). The assessment is based on the geologic elements of each Total Petroleum System defined in the province, including hydrocarbon source rocks (source-rock type and maturation and hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). Using this geologic framework, the USGS defined five total petroleum systems and ten assessment units within these systems. Undiscovered oil and gas resources were quantitatively estimated for the ten assessment units (table 1.1). In addition, the potential was estimated for further growth of reserves in existing oil fields of the San Joaquin Basin.

Depositional environments and oil potential of Jurassic/Cretaceous source rocks within the Seychelles microcontinent

Energy Technology Data Exchange (ETDEWEB)

Plummer, P.S.; Joseph, P.R.; Samson, P.J. [Seychelles National Oil Co., Mahe (Seychelles)

1998-12-31

The Seychelles microcontinent became isolated between the Somali, Mascarene and Arabian basins of the Indian Ocean as a result of the Mesozoic fragmentation of Gondwana. Major rifting events occurred during the Triassic-Middle Jurassic and Late Cretaceous (Cenomanian-Santonian and Maastrichtian) during which shaly source rock facies accumulated in principally marginal marine/deltaic environments. Between these times, post-rift passive margin deposition within restricted to open marine environments produced shaly source rocks during late Middle Jurasic-Early Cretaceous, Campanian-Maastrichtian and Paleocene times. Recent geochemical analysis of cuttings from the Seagull Shoals-1 well has identified an oil-prone liptinitic (Type II) coaly shale within early Middle Jurassic abandoned deltaic deposits. This coaly source rock is regionally developed, having also been identified in the Majunja and Morondava basins of Madagascar. Oil-prone Type II organic matter has also been identified in the Owen Bank A-1 well within restricted marine shales of late Middle Jurassic age. These shales are part of a thick post-rift source rock sequence that extends into the Early Cretaceous and is in part correlative with the proven Late Jurassic Uarandab Shale of Somalia. Analysis of Campanian marine shales from Reith Bank-1 well identified significant dilution of total organic carbon content in composite, compared to picked, well cuttings samples. This finding supports a published inference that these post-rift shales have source rock potential. (author)

An improved method for predicting brittleness of rocks via well logs in tight oil reservoirs

Science.gov (United States)

Wang, Zhenlin; Sun, Ting; Feng, Cheng; Wang, Wei; Han, Chuang

2018-06-01

There can be no industrial oil production in tight oil reservoirs until fracturing is undertaken. Under such conditions, the brittleness of the rocks is a very important factor. However, it has so far been difficult to predict. In this paper, the selected study area is the tight oil reservoirs in Lucaogou formation, Permian, Jimusaer sag, Junggar basin. According to the transformation of dynamic and static rock mechanics parameters and the correction of confining pressure, an improved method is proposed for quantitatively predicting the brittleness of rocks via well logs in tight oil reservoirs. First, 19 typical tight oil core samples are selected in the study area. Their static Young’s modulus, static Poisson’s ratio and petrophysical parameters are measured. In addition, the static brittleness indices of four other tight oil cores are measured under different confining pressure conditions. Second, the dynamic Young’s modulus, Poisson’s ratio and brittleness index are calculated using the compressional and shear wave velocity. With combination of the measured and calculated results, the transformation model of dynamic and static brittleness index is built based on the influence of porosity and clay content. The comparison of the predicted brittleness indices and measured results shows that the model has high accuracy. Third, on the basis of the experimental data under different confining pressure conditions, the amplifying factor of brittleness index is proposed to correct for the influence of confining pressure on the brittleness index. Finally, the above improved models are applied to formation evaluation via well logs. Compared with the results before correction, the results of the improved models agree better with the experimental data, which indicates that the improved models have better application effects. The brittleness index prediction method of tight oil reservoirs is improved in this research. It is of great importance in the optimization of

Application of integrated vitrinite reflectance and FAMM analyses for thermal maturity assessment of the northeastern Malay Basin, offshore Vietnam: Implications for petroleum prospectivity evaluation

DEFF Research Database (Denmark)

Petersen, H. I.; Sherwood, N.; Mathiesen, A.

2008-01-01

Several exploration wells have intersected a Cenozoic coal-bearing, fluvial-deltaic mudstone and sandstone succession in the northeastern Vietnamese part of the Malay Basin, and have successfully tested seismically identified direct hydrocarbon indicators (DHIs). The oil and gas/condensate discov......Several exploration wells have intersected a Cenozoic coal-bearing, fluvial-deltaic mudstone and sandstone succession in the northeastern Vietnamese part of the Malay Basin, and have successfully tested seismically identified direct hydrocarbon indicators (DHIs). The oil and gas...... for the uppermost Oligocene source rocks between 2Ma and present-day, which post-dates trap formation. Seismic facies patterns suggest that lacustrine oil-prone units are in he oil window in the same graben complex a few km NW of the investigated well, and these rocks are likely to be the source of the hydrocarbons....../condensate discovery ell 46-CN-1x encountered a _55m thick section of lacustrine mudstones having considerable potential as an oil source. Vitrinite reflectance (VR) measurements from these alginite-bearing rocks introduce several problems in thermal maturity evaluation, including associated VR suppression...

From rocks to oil : researchers become the first in the world to determine the age of oil

Energy Technology Data Exchange (ETDEWEB)

Crawshaw, C

2005-06-10

This article discussed the discovery of a method to accurately determine the age of oil. The discovery was made by two geologists at the University of Alberta, and provides critical information about the formation of oil which will help to better understand oil deposits. The scientists have suggested that the giant oil sand deposits in Alberta were formed 112 million years ago and not 60 million years ago as was previously thought. They used isotopes of rhenium and osmium, elements found in trace amounts in oil, to pinpoint when oil formed in the Western Canada Sedimentary Basin (WCSB), which contains much of the world's oil sands. It was previously thought that the time at which oil was produced from a rock and migrated as fluid could be deduced from looking at geologic relationships. This is the first time that a direct determination using any isotopic method has be applied to determine age. The research findings are expected to change the way geologists understand the evolution of the basin. It was concluded that while the discovery answers some questions about hydrocarbons, many others remain. However, the presence of an absolute number will help geologists to re-evaluate other knowledge. 1 fig.

The Effect of Salmon Fish’s Oil on Avoidance Learning in Mature Male Rats

Directory of Open Access Journals (Sweden)

Seyed Ebrahim Hosseini

2013-09-01

Full Text Available  Background & Objective: There is plenty of fatty acids of omega-3 in Salmon Fish that affect brain development and function, therefore, this study aimed to investigate the effect of Salmon fish’s oil on learning avoidance in mature male rats.   Materials & Methods: In this empirical study, we used 40 mature male rats that were enrolled into control, sham and experimental groups. The control group was not treated. The sham group received only 1 ml saline daily, 3 experimental groups of different types received 0.25, 0.5 and 0.75 ml/kg body weight respectively, for 28 days. For the evaluation of avoidance learning behavior, the shuttle box was used. The data was evaluated using ANOVA.    Results: The results suggest that consumption of salmon oil significantly increases in minimum and maximum doses (P<0.01 and average doses (P<0.001 the process of avoidance learning.   Conclusion: Salmon oil can lead to increased learning. Therefore, further investigation can be used to treat learning disorders and memory . 

A study of light hydrocarbons (C{sub 4}-C{sub 1}3) in source rocks and petroleum fluid

Energy Technology Data Exchange (ETDEWEB)

Odden, Wenche

2000-07-01

This thesis consists of an introduction and five included papers. Of these, four papers are published in international journals and the fifth was submitted for review in April 2000. Emphasis has been placed on both naturally and artificially generated light hydrocarbons in petroleum fluids and their proposed source rocks as well as direct application of light hydrocarbons to oil/source rock correlations. Collectively, these papers describe a strategy for interpreting the source of the light hydrocarbons in original oils and condensates as well as the source of the asphaltene fractions from the reservoir fluids. The influence of maturity on light hydrocarbon composition has also been evaluated. The papers include (1) compositional data on the light hydrocarbons from thermal extracts and kerogen pyrolysates of sediment samples, (2) light hydrocarbon data of oils and condensates as well as the pyrolysis products of the asphaltenes from these fluids, (3) assessment of compositional alteration effects, such as selective losses of light hydrocarbons due to evaporation, thermal maturity, phase fractionation and biodegradation, (4) comparison of naturally and artificially generated light hydrocarbons, and (5) compound-specific carbon isotope analysis of the whole range of hydrocarbons of all sample types. (author)

Isotopic characterization and genetic origin of crude oils from Gulf of Suez and western desert fields in Egypt

International Nuclear Information System (INIS)

Abd El Samie, S.G.

2006-01-01

Stable carbon isotopes were used to asses the general characteristics of the western desert and Gulf of Suez crude oils in accordance with hydrocarbon generation, source rocks, thermal gradient and maturation level. The carbon isotopic results of all the analyzed oil samples in both areas lie in the range from -29.62 to -24.11 %. The av. σ 13 C values in the Gulf of Suez reaches about -28.6% and -26.4% in western desert. It was accounted a marginal difference between the two areas by about 2.5 : 3% in carbon-13 isotope of the whole oil indicated two distinct oil types of different organic input and varies in the depositional environment. It was found that Gulf of Suez oils are dominated by marine organic matter (plankton algae) deposited in saline environment. The derived oils from the northern and central provinces of the Gulf are isotopically light, higher in sulfur content, lower in API gravity degree and have Pristane/Phytane (Pr/Ph) ratio less than or equal one (Pr/Ph = 1). In the southern province, about 0.5% isotopic enrichment was recorded in the produced oils from shallower depths, associated with gradual increment in API and maturity level as thermal gradient increase. However, low API gravity degree and less maturity of the Gulf of Suez oils could be related to the rifting temperature that forced and accelerated the expulsion rate and hydrocarbon generation prior reaching higher maturation levels. On the other hand, the produced oils from the western desert fields belong mostly to terrestrial organic debris (with minor marine fragment in some basins) deposited at deeper geological formations. It is characterized by isotopic enrichment, paraffinic waxy oils, low in sulphur content, have Pr/Ph = 1, high in API gravity and maturity level. Hydrocarbon generated from the western desert fields has been controlled by time-temperature effect in the source rocks and reservoirs where the humic organic matter are affected by high temperature over longer period of

Effects of smectite on the oil-expulsion efficiency of the Kreyenhagen Shale, San Joaquin Basin, California, based on hydrous-pyrolysis experiments

Science.gov (United States)

Lewan, Michael D.; Dolan, Michael P.; Curtis, John B.

2014-01-01

The amount of oil that maturing source rocks expel is expressed as their expulsion efficiency, which is usually stated in milligrams of expelled oil per gram of original total organic carbon (TOCO). Oil-expulsion efficiency can be determined by heating thermally immature source rocks in the presence of liquid water (i.e., hydrous pyrolysis) at temperatures between 350°C and 365°C for 72 hr. This pyrolysis method generates oil that is compositionally similar to natural crude oil and expels it by processes operative in the subsurface. Consequently, hydrous pyrolysis provides a means to determine oil-expulsion efficiencies and the rock properties that influence them. Smectite in source rocks has previously been considered to promote oil generation and expulsion and is the focus of this hydrous-pyrolysis study involving a representative sample of smectite-rich source rock from the Eocene Kreyenhagen Shale in the San Joaquin Basin of California. Smectite is the major clay mineral (31 wt. %) in this thermally immature sample, which contains 9.4 wt. % total organic carbon (TOC) comprised of type II kerogen. Compared to other immature source rocks that lack smectite as their major clay mineral, the expulsion efficiency of the Kreyenhagen Shale was significantly lower. The expulsion efficiency of the Kreyenhagen whole rock was reduced 88% compared to that of its isolated kerogen. This significant reduction is attributed to bitumen impregnating the smectite interlayers in addition to the rock matrix. Within the interlayers, much of the bitumen is converted to pyrobitumen through crosslinking instead of oil through thermal cracking. As a result, smectite does not promote oil generation but inhibits it. Bitumen impregnation of the rock matrix and smectite interlayers results in the rock pore system changing from water wet to bitumen wet. This change prevents potassium ion (K+) transfer and dissolution and precipitation reactions needed for the conversion of smectite to

Mature oil palm plantations are thirstier than tropical forests

Science.gov (United States)

Manoli, G.; Meijide, A.; Huth, N.; Knohl, A.; Kosugi, Y.; Burlando, P.; Ghazoul, J.; Fatichi, S.

2017-12-01

Oil Palm (OP) is the highest yielding cash-crop in the world but, being the driver of significant tropical forest losses, it is also considered the "world's most hated crop". Despite substantial research on the impact of OP on ecosystem degradation, biodiversity losses, and carbon emissions, little is known on the ecohydrological impacts of forest conversion to OP. Here we employ numerical simulations constrained by field observations to quantify changes in ecosystem evapotranspiration (ET), infiltration/runoff, gross primary productivity (GPP) and surface temperature (Ts) due to OP establishment. Compared to pristine forests, young OP plantations decrease ET, causing an increase in Ts, but the changes become less pronounced as plantations grow. Mature plantations have a very high GPP to sustain the oil palm yield and, given relatively similar water use efficiency, they transpire more water that the forests they have replaced. Hence, the high fruit productivity of OP comes at the expense of water consumption. Our mechanistic modeling results corroborate anecdotal evidence of water scarcity issues in OP-dominated landscapes.

Thermal maturity of northern Appalachian Basin Devonian shales: Insights from sterane and terpane biomarkers

Science.gov (United States)

Hackley, Paul C.; Ryder, Robert T.; Trippi, Michael H.; Alimi, Hossein

2013-01-01

To better estimate thermal maturity of Devonian shales in the northern Appalachian Basin, eleven samples of Marcellus and Huron Shale were characterized via multiple analytical techniques. Vitrinite reflectance, Rock–Eval pyrolysis, gas chromatography (GC) of whole rock extracts, and GC–mass spectrometry (GCMS) of extract saturate fractions were evaluated on three transects that lie across previously documented regional thermal maturity isolines. Results from vitrinite reflectance suggest that most samples are immature with respect to hydrocarbon generation. However, bulk geochemical data and sterane and terpane biomarker ratios from GCMS suggest that almost all samples are in the oil window. This observation is consistent with the presence of thermogenic gas in the study area and higher vitrinite reflectance values recorded from overlying Pennsylvanian coals. These results suggest that vitrinite reflectance is a poor predictor of thermal maturity in early mature areas of Devonian shale, perhaps because reported measurements often include determinations of solid bitumen reflectance. Vitrinite reflectance interpretations in areas of early mature Devonian shale should be supplanted by evaluation of thermal maturity information from biomarker ratios and bulk geochemical data.

Influence of the mineral composition of clay rocks on the stability of oil wells

International Nuclear Information System (INIS)

Amorocho, P. R; Badillo, Juan

2012-01-01

In the oil companies, the operation of drilling well bore could be more expensive if the composition of the rocks is clay, the cost could increase between 10 and 15% from the starting budget. In order to decrease this problem, the oil industry has spent too much money for developing mechanisms that can provide better control and stability in clay formations during the drilling. The Society Petroleum Engineers (SPE) in some researches have published that the main chemical effects that are involved in the interaction of perforation fluids and the clay formation are: 1) chemical osmosis; and 2) hydration stresses, although, there are others like: Capillary effects, dehydration, differences in pressure and cationic exchange. These factors are not present generally in independent form. At Piedemonte Llanero the problem of the well bore stability represents a high spending of money for oil companies, caused in this region by chemical factors between fluid/rock and mechanical factors as resulted of the stresses in the area. Metil Blue Testing (MBT) and X-ray Diffraction (DR-X) were made in samples of clay; these were taken from cuts extracted of boreholes drilled in some places of the Colombian Llanos. It was found that these samples had a moderate content of reactive and low content of swell minerals.The samples main component was kaolinite, this mineral does not let the rock get swell, but it produces caving in the hole. However, it is necessary to do other tests to quantify the damages and evaluate the influence of there gime of the stress during the perforation of well bore.

Impact of dia- and catagenesis on sulphur and oxygen sequestration of biomarkers as revealed by artificial maturation of an immature sedimentary rock

Science.gov (United States)

Koopmans, M.P.; De Leeuw, J. W.; Lewan, M.D.; Sinninghe, Damste J.S.

1996-01-01

Hydrous pyrolysis of an immature (R(a)??? 0.25%) sulphur-rich marl from the Gessoso-solfifera Formation (Messinian) in the Vena del Gesso Basin was carried out at 160C ??? T ???330 C for 72 h, to study the effect of progressive diagenesis and early catagenesis on the abundance and distribution of sulphur-containing and sulphur- and oxygen-linked carbon skeletons in low-molecular-weight and highmolecular-weight fractions (e.g. kerogen). To this end, compounds in the saturated hydrocarbon fraction, monoaromatic hydrocarbon fraction, polyaromatic hydrocarbon fraction, alkylsulphide fraction and ketone fraction were quantified, as well as compounds released after desulphurisation of the polar fraction and HI/LiAIH4 treatment of the desulphurised polar fraction. Sulphur-bound phytane and (20R)-5??,14??,17??(H) and (20R)-5??,14??,17??(H) C27 C29 steranes in the polar fraction become less abundant with increasing maturation temperature, whereas the amount of their corresponding hydrocarbons increases in the saturated hydrocarbon fraction. Carbon skeletons that are bound in the kerogen by multiple bonds (e.g. C38 n-alkane and isorenieratane) are first released into the polar fraction, and then as free hydrocarbons. These changes occur at relatively low levels of thermal maturity (R(a) <0.6%), as evidenced by the 'immature' values of biomarker maturity parameters such as the ????/(????+ ???? + ????) C35 hopane ratio and the 22S/(22S + 22R)-17??,21??(H) C35 hopane ratio. Sulphur- and oxygen-bound moieties, present in the polar fraction, are not stable with increasing thermal maturation. However, alkylthiophenes, ketones. 1,2-di-n-alkylbenzenes and free n-alkanes seem to be stable thermal degradation products of these sulphur- and oxygen-bound moieties. Thus, apart from free n-alkanes, which are abundantly present in more mature sedimentary rocks and crude oils, alkylthiophenes, 1,2-di-n-alkylbenzenes and ketones can also be expected to occur. The positions of the thiophene

2D seismic interpretation and characterization of the Hauterivian-Early Barremian source rock in Al Baraka oil field, Komombo Basin, Upper Egypt

Science.gov (United States)

Ali, Moamen; Darwish, M.; Essa, Mahmoud A.; Abdelhady, A.

2018-03-01

Komombo Basin is located in Upper Egypt about 570 km southeast of Cairo; it is an asymmetrical half graben and the first oil producing basin in Upper Egypt. The Six Hills Formation is of Early Cretaceous age and subdivided into seven members from base to top (A-G); meanwhile the B member is of Hauterivian-Early Barremian and it is the only source rock of Komombo Basin. Therefore, a detailed study of the SR should be carried out, which includes the determination of the main structural elements, thickness, facies distribution and characterization of the B member SR which has not been conducted previously in the study area. Twenty 2D seismic lines were interpreted with three vertical seismic profiles (VSP) to construct the depth structure-tectonic map on the top of the B member and to highlight the major structural elements. The interpretation of depth structure contour map shows two main fault trends directed towards the NW-SE and NE to ENE directions. The NW-SE trend is the dominant one, creating a major half-graben system. Also the depth values range from -8400 ft at the depocenter in the eastern part to -4800 ft at the shoulder of the basin in the northwestern part of the study area. Meanwhile the Isopach contour map of the B member shows a variable thickness ranging between 300 ft to 750 ft. The facies model shows that the B member SR is composed mainly of shale with some sandstone streaks. The B member rock samples were collected from Al Baraka-1 and Al Baraka SE-1 in the eastern part of Komombo Basin. The results indicate that the organic matter content (TOC) has mainly good to very good (1-3.36 wt %), The B member samples have HI values in the range 157-365 (mg HC/g TOC) and dominated by Type II/III kerogen, and is thus considered to be oil-gas prone based on Rock-Eval pyrolysis, Tmax values between 442° and 456° C therefore interpreted to be mature for hydrocarbon generation. Based on the measured vitrinite equivalent reflectance values, the B member SR

The Rho-GTPase effector ROCK regulates meiotic maturation of the bovine oocyte via myosin light chain phosphorylation and cofilin phosphorylation.

Science.gov (United States)

Lee, So-Rim; Xu, Yong-Nan; Jo, Yu-Jin; Namgoong, Suk; Kim, Nam-Hyung

2015-11-01

Oocyte meiosis involves a unique asymmetric division involving spindle movement from the central cytoplasm to the cortex, followed by polar body extrusion. ROCK is a Rho-GTPase effector involved in various cellular functions in somatic cells as well as oocyte meiosis. ROCK was previously shown to promote actin organization by phosphorylating several downstream targets, including LIM domain kinase (LIMK), phosphorylated cofilin (p-cofilin), and myosin light chain (MLC). In this study, we investigated the roles of ROCK and MLC during bovine oocyte meiosis. We found that ROCK was localized around the nucleus at the oocyte's germinal-vesicle (GV) stage, but spreads to the rest of the cytoplasm in later developmental stages. On the other hand, phosphorylated MLC (p-MLC) localized at the cortex, and its abundance decreased by the metaphase-II stage. Disrupting ROCK activity, via RNAi or the chemical inhibitor Y-27632, blocked both cell cycle progression and polar body extrusion. ROCK inhibition also resulted in decreased cortical actin, p-cofilin, and p-MLC levels. Similar to the phenotype associated with inhibition of ROCK activity, inhibition of MLC kinase by the chemical inhibitor ML-7 caused defects in polar body extrusion. Collectively, our results suggest that the ROCK/MLC/actomyosin as well as ROCK/LIMK/cofilin pathways regulate meiotic spindle migration and cytokinesis during bovine oocyte maturation. © 2015 Wiley Periodicals, Inc.

DEPOSITIONAL ENVIRONMENT AND ORGANIC GEOCHEMICAL CHARACTERISTICS OF LOWER EOCENE BITUMINOUS ROCKS, IN THE KÜRNÜÇ/GÖYNÜK-BOLU AREA

Directory of Open Access Journals (Sweden)

Ali SARI

2016-12-01

Full Text Available In this study, dark gray and dark brown colored, organic-carbon rich bituminous rocks (bituminous marl and bituminous shale exposing around the Kürnüç area (Göynük, Bolu are investigated by means of or- ganic geochemical characteristics. In this respect, rock lithologies, depositional environments, rock source potential, kerogen and organic maturity types and hydrocarbon generation potentials of bituminous rocks were determined. For this reason, pyrolysis (Rock Eval–VI analysis, gas chromatography (GC and gas chromatography-mass spectrometer (GC-MS analyses were carried out. In addition, spore color index (SCI was determined with organic petrographic method and stable carbon analysis (δ13C of the samples were also conducted. Lithology of the studied samples is of clastic source and the depositional environ- ment is a lagoon with a partial connection to the sea. In bituminous rocks with excellent source rock potential TOC values are in the range of 2.52-8.38 wt % (average 6.08 wt %. With the exception of two samples (Type II kerogen type of all samples is Type I. According to pyrolysis, GC and GC-MS organic maturity results, all the samples are in immature stage. Organic geochemical data indicate that bituminous rocks have an excellent oil generation potential and there is no organic contamination.

Effect of clay content in rock on oil extraction under alkaline seam conditions

Energy Technology Data Exchange (ETDEWEB)

Vezirov, D Sh; Gorbunov, A T; Kasimov, Sh A; Kashchavtsev, V E; Tairov, N D

1978-01-01

When oil beds are flooded with alkaline solutions, the alkaline concentration in the solution can be significantly reduced as a result of the interaction between clay and alkali. Large losses of alkali in the bed can render the flooding method ineffective. Experimental studies were conducted on porous media containing up to 25% clay at a constant permeability of 1 D in order to determine the oil extraction indices for clay-containing rock. Constant permeability is maintained by using clays, marshalite, and quartz sand in various proportions. Oil having a viscosity of 99.17 sP, and containing a large amount of surfactants, including 1.1% naphthenic acid, was extracted by fresh water and a 0.25% solution of NaOH. The extraction of oil by fresh water and NaOH solution from quartz sand indicated the advantage of using alkaline solutions. The extraction coefficient increased by 11% with the use of this method. As clay is added to the sand, the extraction coefficient decreases, and is reduced to 12.7% when the clay content reaches 25%. Nevertheless, a comparison of data obtained for quartz sand with fresh water on a porous medium containing 25% clay with an alkaline solution, indicates that the extraction coefficient is just 1.5% lower even in the presence of such a large amount of clay. Consequently, alkaline flooding should still be given preference over the usual methods under specific conditions and where the rock has a comparatively large amount of clay, in view of all the basic factors that influence the extraction process. The results obtained can be used for selecting alkaline concentration in evaluating the efficiency of flooding oil beds with alkaline solutions. 2 figures, 2 tables.

Effects of CO2 injection and Kerogen Maturation on Low-Field Nuclear Magnetic Resonance Response

Science.gov (United States)

Prasad, M.; Livo, K.

2017-12-01

Low-field Nuclear Magnetic Resonance (NMR) is commonly used in petrophysical analysis of petroleum reservoir rocks. NMR experiments record the relaxation and polarization of in-situ hydrogen protons present in gaseous phases such as free-gas intervals and solution gas fluids, bulk fluid phases such as oil and aquifer intervals, and immovable fractions of kerogen and bitumen. Analysis of NMR relaxation spectra is performed to record how fluid composition, maturity, and viscosity change NMR experimental results. We present T1-T2 maps as thermal maturity of a water-saturated, sub-mature Woodford shale is increased at temperatures from 125 to 400 degrees Celsius. Experiments with applied fluid pressure in paraffinic mineral oil and DI water with varying fluid pH have been performed to mimic reservoir conditions in analysis of the relaxation of bulk fluid phases. We have recorded NMR spectra, T1-T2 maps, and fluid diffusion coefficients using a low-field (2 MHz) MagritekTM NMR. CO2 was injected at a pressure of 900 psi in an in house developed NMR pressure vessel made of torlon plastic. Observable 2D NMR shifts in immature kerogen formations as thermal maturity is increased show generation of lighter oils with increased maturity. CO2 injection leads to a decrease in bulk fluid relaxation time that is attributed to viscosity modification with gas presence. pH variation with increased CO2 presence were shown to not effect NMR spectra. From this, fluid properties have been shown to greatly affect NMR readings and must be taken into account for more accurate NMR reservoir characterization.

Effects of different levels of lespedeza and supplementation with monensin, coconut oil, or soybean oil on ruminal methane emission by mature Boer goat wethers after different lengths of feeding

Science.gov (United States)

Mature Boer goat wethers were supplemented with 0.5% BW rolled corn and consumed pelleted alfalfa (CON), pelleted Sericea lespedeza (HSL; 6.4% condensed tannins), a 1:1 mixture of alfalfa and lespedeza (MSL), or alfalfa with monensin (ION; 22 mg/kg), coconut oil (CCO; 4%), or soybean oil (SBO; 4%). ...

Executive summary--2002 assessment of undiscovered oil and gas resources in the San Juan Basin Province, exclusive of Paleozoic rocks, New Mexico and Colorado: Chapter 1 in Total petroleum systems and geologic assessment of undiscovered oil and gas resources in the San Juan Basin Province, exclusive of Paleozoic rocks, New Mexico and Colorado

Science.gov (United States)

,

2013-01-01

In 2002, the U.S. Geological Survey (USGS) estimated undiscovered oil and gas resources that have the potential for additions to reserves in the San Juan Basin Province (5022), New Mexico and Colorado (fig. 1). Paleozoic rocks were not appraised. The last oil and gas assessment for the province was in 1995 (Gautier and others, 1996). There are several important differences between the 1995 and 2002 assessments. The area assessed is smaller than that in the 1995 assessment. This assessment of undiscovered hydrocarbon resources in the San Juan Basin Province also used a slightly different approach in the assessment, and hence a number of the plays defined in the 1995 assessment are addressed differently in this report. After 1995, the USGS has applied a total petroleum system (TPS) concept to oil and gas basin assessments. The TPS approach incorporates knowledge of the source rocks, reservoir rocks, migration pathways, and time of generation and expulsion of hydrocarbons; thus the assessments are geologically based. Each TPS is subdivided into one or more assessment units, usually defined by a unique set of reservoir rocks, but which have in common the same source rock. Four TPSs and 14 assessment units were geologically evaluated, and for 13 units, the undiscovered oil and gas resources were quantitatively assessed.

Acoustic and Petrophysical Evolution of Organic-Rich Chalk Following Maturation Induced by Unconfined Pyrolysis

Science.gov (United States)

Shitrit, Omri; Hatzor, Yossef H.; Feinstein, Shimon; Vinegar, Harold J.

2017-12-01

Thermal maturation is known to influence the rock physics of organic-rich rocks. While most studies were performed on low-porosity organic-rich shales, here we examine the effect of thermal maturation on a high-porosity organic-rich chalk. We compare the physical properties of native state immature rock with the properties at two pyrolysis-simulated maturity levels: early-mature and over-mature. We further evaluate the applicability of results from unconfined pyrolysis experiments to naturally matured rock properties. Special attention is dedicated to the elastic properties of the organic phase and the influence of bitumen and kerogen contents. Rock physics is studied based on confined petrophysical measurements of porosity, density and permeability, and measurements of bedding-normal acoustic velocities at estimated field stresses. Geochemical parameters like total organic carbon (TOC), bitumen content and thermal maturation indicators are used to monitor variations in density and volume fraction of each phase. We find that porosity increases significantly upon pyrolysis and that P wave velocity decreases in accordance. Solids density versus TOC relationships indicate that the kerogen increases its density from 1.43 to 1.49 g/cc at the immature and early-mature stages to 2.98 g/cc at the over-mature stage. This density value is unusually high, although increase in S wave velocity and backscatter SEM images of the over-mature samples verify that the over-mature kerogen is significantly denser and stiffer. Using the petrophysical and acoustic properties, the elastic moduli of the rock are estimated by two Hashin-Shtrikman (HS)-based models: "HS + BAM" and "HS kerogen." The "HS + BAM" model is calibrated to the post-pyrolysis measurements to describe the mechanical effect of the unconfined pyrolysis on the rock. The absence of compaction in the pyrolysis process causes the post-pyrolysis samples to be extremely porous. The "HS kerogen" model, which simulates a

Geology and sequence stratigraphy of undiscovered oil and gas resources in conventional and continuous petroleum systems in the Upper Cretaceous Eagle Ford Group and related strata, U.S. Gulf Coast Region

Science.gov (United States)

Dubiel, Russell F.; Pearson, Ofori N.; Pitman, Janet K.; Pearson, Krystal M.; Kinney, Scott A.

2012-01-01

The U.S. Geological Survey (USGS) recently assessed the technically recoverable undiscovered oil and gas onshore and in State waters of the Gulf Coast region of the United States. The USGS defined three assessment units (AUs) with potential undiscovered conventional and continuous oil and gas resources in Upper Cretaceous (Cenomanian to Turonian) strata of the Eagle Ford Group and correlative rocks. The assessment is based on geologic elements of a total petroleum system, including hydrocarbon source rocks (source rock maturation, hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and traps (formation, timing, and seals). Conventional oil and gas undiscovered resources are in updip sandstone reservoirs in the Upper Cretaceous Tuscaloosa and Woodbine Formations (or Groups) in Louisiana and Texas, respectively, whereas continuous oil and continuous gas undiscovered resources reside in the middip and downdip Upper Cretaceous Eagle Ford Shale in Texas and the Tuscaloosa marine shale in Louisiana. Conventional resources in the Tuscaloosa and Woodbine are included in the Eagle Ford Updip Sandstone Oil and Gas AU, in an area where the Eagle Ford Shale and Tuscaloosa marine shale display vitrinite reflectance (Ro) values less than 0.6%. The continuous Eagle Ford Shale Oil AU lies generally south of the conventional AU, is primarily updip of the Lower Cretaceous shelf edge, and is defined by thermal maturity values within shales of the Eagle Ford and Tuscaloosa that range from 0.6 to 1.2% Ro. Similarly, the Eagle Ford Shale Gas AU is defined downdip of the shelf edge where source rocks have Ro values greater than 1.2%. For undiscovered oil and gas resources, the USGS assessed means of: 1) 141 million barrels of oil (MMBO), 502 billion cubic feet of natural gas (BCFG), and 4 million barrels of natural gas liquids (MMBNGL) in the Eagle Ford Updip Sandstone Oil and Gas AU; 2) 853 MMBO, 1707 BCFG, and 34 MMBNGL in the

Families of miocene monterey crude oil, seep, and tarball samples, coastal California

Science.gov (United States)

Peters, K.E.; Hostettler, F.D.; Lorenson, T.D.; Rosenbauer, R.J.

2008-01-01

Biomarker and stable carbon isotope ratios were used to infer the age, lithology, organic matter input, and depositional environment of the source rocks for 388 samples of produced crude oil, seep oil, and tarballs to better assess their origins and distributions in coastal California. These samples were used to construct a chemometric (multivariate statistical) decision tree to classify 288 additional samples. The results identify three tribes of 13C-rich oil samples inferred to originate from thermally mature equivalents of the clayey-siliceous, carbonaceous marl and lower calcareous-siliceous members of the Monterey Formation at Naples Beach near Santa Barbara. An attempt to correlate these families to rock extracts from these members in the nearby COST (continental offshore stratigraphic test) (OCS-Cal 78-164) well failed, at least in part because the rocks are thermally immature. Geochemical similarities among the oil tribes and their widespread distribution support the prograding margin model or the banktop-slope-basin model instead of the ridge-and-basin model for the deposition of the Monterey Formation. Tribe 1 contains four oil families having geochemical traits of clay-rich marine shale source rock deposited under suboxic conditions with substantial higher plant input. Tribe 2 contains four oil families with traits intermediate between tribes 1 and 3, except for abundant 28,30-bisnorhopane, indicating suboxic to anoxic marine marl source rock with hemipelagic input. Tribe 3 contains five oil families with traits of distal marine carbonate source rock deposited under anoxic conditions with pelagic but little or no higher plant input. Tribes 1 and 2 occur mainly south of Point Conception in paleogeographic settings where deep burial of the Monterey source rock favored petroleum generation from all three members or their equivalents. In this area, oil from the clayey-siliceous and carbonaceous marl members (tribes 1 and 2) may overwhelm that from the lower

The oil potential of the BM-J-2 block, Jequitinhonha basin, Brazil: the integrated study of the basin analysis and modeling of petroleum system; Potencial petrolifero do Bloco BM-J-2, Bacia de Jequitinhonha, Brasil: um estudo integrado de analise de bacia e modelagem de sistemas petroliferos

Energy Technology Data Exchange (ETDEWEB)

Porto, Roberto; Braga, Jose A.E.; Saito, Makoto; Cortez, Marcella; Ponte Filho, Francisco C.; Romao, Felipe [Queiroz Galvao Perfuracoes S.A., Rio de Janeiro, RJ (Brazil); Goncalves, Felix T.T. [PGT-Petroleum Geoscience Technology Ltd., Rio de Janeiro, RJ (Brazil)

2004-07-01

The integration of all available geochemical data from this and adjoining blocks (BM-J-1 e BM-J-3) Jequitinhonha Basin revealed that only the Albian-Turonian and Aptian sections contains potential hydrocarbon source rock intervals. The existence of an oil accumulation (1-BAS-37) represents an unequivocal evidence of the presence of effective source rocks in the Jequitinhonha Basin. The geochemical characteristics of this oil accumulation points to an origin related to petroleum source rocks deposited under a lacustrine/marine restricted (hyper saline) environment. Such characteristics are typical of pre-salt Aptian source rocks in several basins along the Brazilian margin. The pseudo-3D modeling results indicate that the stage of thermal evolution of the base of the rift section attained ranges from early mature (0.6-0.8 Ro) in the structural highs to over mature (up to 2.0% Ro) in the structural lows On the other hand, the potential sources rocks of Albian-Turonian age ranges to immature to early mature throughout the block. The modeling results also points to the existence of two distinct hydrocarbon 'kitchens': one located in the easternmost portion of the block (slope/deep water area) and the other in a structural low located in the shallow platform area. The main phase of petroleum expulsion ranged from Late Cretaceous/Paleogene in the platform area. Probabilistic simulations has estimated migrated oils and gas volumes around 507 MMbbl and 20 billion cubic meters, respectively. (author)

Extraction of Iodine from Source Rock and Oil for Radioiodine Dating Final Report CRADA No. TC-1550-98

Energy Technology Data Exchange (ETDEWEB)

Moran, J. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Summa, L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-10-19

This was a collaborative effort between the University of California, Lawrence Livermore National Laboratory (LLNL) and Exxon Production Research Company (EPR) to develop improved techniques for extracting, concentrating, and measuring iodine from large volumes of source rock and oil. The purpose of this project was to develop a technique for measuring total iodine extracted from rock, obtain isotopic ratios, and develop age models for samples provided by EPR.

Proteomic analysis of oil bodies in mature Jatropha curcas seeds with different lipid content.

Science.gov (United States)

Liu, Hui; Wang, Cuiping; Chen, Fan; Shen, Shihua

2015-01-15

To reveal the difference among three mature Jatropha curcas seeds (JcVH, variant with high lipid content; JcW, wild type and JcVL, variant with low lipid content) with different lipid content, comparative proteomics was employed to profile the changes of oil body (OB) associated protein species by using gels-based proteomic technique. Eighty-three protein species were successfully identified through LTQ-ES-MS/MS from mature JcW seeds purified OBs. Two-dimensional electrophoresis analysis of J. curcas OB associated protein species revealed they had essential interactions with other organelles and demonstrated that oleosin and caleosin were the most abundant OB structural protein species. Twenty-eight OB associated protein species showed significant difference among JcVH, JcW and JcVL according to statistical analysis. Complementary transient expression analysis revealed that calcium ion binding protein (CalBP) and glycine-rich RNA binding protein (GRP) were well targeted in OBs apart from the oleosins. This study demonstrated that ratio of lipid content to caleosins abundance was involved in the regulation of OB size, and the mutant induced by ethylmethylsulfone treatment might be related to the caleosin like protein species. These findings are important for biotechnological improvement with the aim to alter the lipid content in J. curcas seeds. The economic value of Jatropha curcas largely depends on the lipid content in seeds which are mainly stored in the special organelle called oil bodies (OBs). In consideration of the biological importance and applications of J. curcas OB in seeds, it is necessary to further explore the components and functions of J. curcas OBs. Although a previous study concerning the J. curcas OB proteome revealed oleosins were the major OB protein component and additional protein species were similar to those in other oil seed plants, these identified OB associated protein species were corresponding to the protein bands instead of protein

Carbon-13 isotopic composition of distillation fractions of some Egyptian crude oils

International Nuclear Information System (INIS)

Aly, A.I.M.; Hamza, M.S.; Abd Elsamie, S.G.

1991-01-01

13 C/ 13 C ratios were determined for some crude oil fields in the Gulf of Suez and Western Desert provinces. The crude oil was subjected to distillation at atmospheric pressure and subsequently under vacuum. Distillation fractions were collected at 25 degree C intervals. Carbon-13 content of these distillation fractions showed some differences in the degree of isotopic fractionation. The results were interpreted in view of the age of the source rocks and the degree of maturation process. The carbon-13 content of distillation fractions may be helpful in revealing petroleum mechanisms which can be exploited in exploration.4 fig

Phosphate-rich sedimentary rocks: significance for organic facies and petroleum exploration

Energy Technology Data Exchange (ETDEWEB)

Waples, D W

1982-03-01

Phosphorus-bearing rocks and sediments can be divided into two genetically distinct classes: phosphatic shales or limestones and phosphorites. Phosphatic shales are primary sediments in which phosphate nodules or micronodules have formed diagenetically by precipitation of calcium phosphates derived mainly from organic phosphorus. The nodules form in reducing environments at shallow depths within the sediments, where loss of phosphate by diffusion to the overlying water column is minimized. Highly biogenic sediments containing large amounts of organic matter and some fine clastic debris provide ideal environments for the formation of phosphate nodules. Phosphorites, in contrast, represent concentrated accumulations of reworked phosphate nodules which originated in phosphatic shales or limestones. Currents, wave action, recrystallization, and erosion and resedimentation are important mechanisms in the concentration process. Phosphatic shales and limestones may become excellent oil source rocks if thermal maturity is achieved. They are useful facies indicators for anoxic or nearly anoxic depositional environments, and are often associated with restricted basins, or, during certain geologic periods, with broad shelves developed during transgressions. Phosphorites, in contrast, are often correlated with sea-level regressions or uplifts. They are modest source rocks because of their low organic carbon contents and the fact that they were reworked under oxidizing conditions. Nevertheless, because phosphorites are derived from, and often grade into, phosphatic shales, they also are of potential utility in the search for oil source beds.

An experimental investigation of geochromatography during secondary migration of petroleum performed under subsurface conditions with a real rock

Directory of Open Access Journals (Sweden)

Larter Steve

2000-10-01

Full Text Available An understanding of the size of petroleum secondary migration systems is vital for successful exploration for petroleum reserves. Geochemists have suggested that compositional fractionation of petroleum accompanying the migration process (geochromatography can potentially be used to infer distances petroleum may have travelled and the ratio of oil in the reservoir to that lost in the carrier. To date, this has been attempted by measuring concentrations and distributions of specific steranes, and aromatic oxygen and nitrogen compounds in reservoired oils which have been proposed to respond to migration rather than to source maturity or other effects. We report here an experiment involving oil migration through an initially water wet siltstone under realistic subsurface carrier bed or reservoir conditions (48 MPa, 70°C where source facies and maturity effects are eliminated. We show that geochromatography does indeed occur even for initially water-saturated rocks and that the migration fractionations observed for alkylcarbazoles, benzocarbazoles and alkylphenols are very similar to those seen in field data sets. In contrast, sterane based migration parameters show no compositional fractionation under these conditions.

Total petroleum systems and geologic assessment of undiscovered oil and gas resources in the San Juan Basin Province, exclusive of Paleozoic rocks, New Mexico and Colorado

Science.gov (United States)

,

2013-01-01

In 2002, the U.S. Geological Survey (USGS) estimated undiscovered oil and gas resources that have the potential for additions to reserves in the San Juan Basin Province, New Mexico and Colorado. Paleozoic rocks were not appraised. The last oil and gas assessment for the province was in 1995. There are several important differences between the 1995 and 2002 assessments. The area assessed is smaller than that in the 1995 assessment. This assessment of undiscovered hydrocarbon resources in the San Juan Basin Province also used a slightly different approach in the assessment, and hence a number of the plays defined in the 1995 assessment are addressed differently in this report. After 1995, the USGS has applied a total petroleum system (TPS) concept to oil and gas basin assessments. The TPS approach incorporates knowledge of the source rocks, reservoir rocks, migration pathways, and time of generation and expulsion of hydrocarbons; thus the assessments are geologically based. Each TPS is subdivided into one or more assessment units, usually defined by a unique set of reservoir rocks, but which have in common the same source rock. Four TPSs and 14 assessment units were geologically evaluated, and for 13 units, the undiscovered oil and gas resources were quantitatively assessed.

Evaluating Re-Os systematics in organic-rich sedimentary rocks in response to petroleum generation using hydrous pyrolysis experiments

Science.gov (United States)

Rooney, A.D.; Selby, D.; Lewan, M.D.; Lillis, P.G.; Houzay, J.-P.

2012-01-01

Successful application of the 187Re–187Os geochronometer has enabled the determination of accurate and precise depositional ages for organic-rich sedimentary rocks (ORS) as well as establishing timing constraints of petroleum generation. However, we do not fully understand the systematics and transfer behaviour of Re and Os between ORS and petroleum products (e.g., bitumen and oil). To more fully understand the behaviour of Re–Os systematics in both source rocks and petroleum products we apply hydrous pyrolysis to two immature hydrocarbon source rocks: the Permian Phosphoria Formation (TOC = 17.4%; Type II-S kerogen) and the Jurassic Staffin Formation (TOC = 2.5%; Type III kerogen). The laboratory-based hydrous pyrolysis experiments were carried out for 72 h at 250, 300, 325 and 350 °C. These experiments provided us with whole rock, extracted rock and bitumen and in some cases expelled oil and asphaltene for evaluation of Re–Os isotopic and elemental abundance. The data from these experiments demonstrate that the majority (>95%) of Re and Os are housed within extracted rock and that thermal maturation does not result in significant transfer of Re or Os from the extracted rock into organic phases. Based on existing thermodynamic data our findings suggest that organic chelating sites have a greater affinity for the quadravalent states of Re and Os than sulphides. Across the temperature range of the hydrous pyrolysis experiments both whole rock and extracted rock 187Re/188Os ratios show small variations (3.3% and 4.7%, for Staffin, respectively and 6.3% and 4.9% for Phosphoria, respectively). Similarly, the 187Os/188Os ratios show only minor variations for the Staffin and Phosphoria whole rock and extracted rock samples (0.6% and 1.4% and 1.3% and 2.2%). These isotopic data strongly suggest that crude oil generation through hydrous pyrolysis experiments does not disturb the Re–Os systematics in ORS as supported by various studies on natural systems. The

New insights on the maturity distribution and shale gas potential of the Lower Saxony Basin, NW-Germany

Energy Technology Data Exchange (ETDEWEB)

Bruns, B.; Littke, R. [RWTH Aachen Univ. (Germany). Energy and Mineral Resources Group (EMR); Di Primio, R. [Deutsches GeoForchungsZentrum (GFZ), Potsdam (Germany). Sektion 4.3 - Organische Geochemie; Berner, U. [Bundesanstalt fuer Geowissenschaften und Rohstoffe (BGR), Hannover (Germany)

2013-08-01

Due to its economic relevance the Lower Saxony Basin has been intensively investigated. Consequently it can be regarded as a well-known example of a sedimentary basin that experienced strong inversion. Oil and gas source rocks of economical importance comprise Upper Carboniferous coals as well as Jurassic (Toarcian/Posidonia Shale) and Cretaceous (Berriasian/Wealden) marls. Many basin modeling projects have addressed this area but until now the tectonic and maturation history as well as the petroleum system evolution has not been evaluated in a high-resolution 3D model. Therefore, a fully integrated 3D high-resolution numerical petroleum system model was developed incorporating the Lower Saxony Basin and major parts of the Pompeckj Block, and Muensterland Basin. The burial and maturation history has been reconstructed calibrated by large amounts of vitrinite reflectance and downhole temperature data enabling the output of erosion and maturity distribution maps of superior quality. (orig.)

Oil geology of carbonate rock (Part 9)

Energy Technology Data Exchange (ETDEWEB)

Oshima, Kazuaki [Canpex Co., Ltd., Tokyo (Japan)

1989-04-01

As related with the oil exploration and development, the geological and environmental situation, where coral and other biological reef forms, was explained in Mubarras shoal and Bu Tinah shoal off Abu Dhabi, and the Okinawa islands. Generally, reef-natured sediment is distributed in marine areas, high in wave energy and facing open sea, and composed of coarse sediment. While, for the formation of biological reef, life must have so strong skeleton as to stand such severe wave, current and other oceanographic conditions. In Mubarras shoal, underground upheaval is found mainly in the northern part of shoal, while, in Bu Tinah shoal, it is found at the central part of shoal. Both the shoals are mutually different in condition of coral reef and coarse particulate sediment however common in the point that coral reef is always formed from the central part of upheaval toward offshore, inside which formation coarse calcareous sediment is formed. While the existence of calcareous mud prevents coral from growing and simultaneously lower reservoir rock in form condition. 26 figs.

La pyrolyse Rock-Eval et ses applications. Troisième partie. Rock-Eval Pyrolysis and Its Applications (Part Three

Directory of Open Access Journals (Sweden)

Espitalie J.

2006-11-01

Full Text Available Conçue pour répondre aux besoins de l'exploration pétrolière, la méthode de pyrolyse Rock-Eval est maintenant largement utilisée. Elle fournit, en effet, et d'une façon rapide, différentes informations sur le contenu organique des roches, telles que le potentiel pétrolier des séries rencontrées, la nature des kérogènes, leur état de maturation. En ce qui concerne le matériel, deux nouvelles versions ont été mises au point à l'Institut Français du Pétrole (IFP depuis l'apparition en 1977 des premiers appareils Rock-Eval : un Rock-Eval II complètement automatisé grâce à un microprocesseur et doté, en option, d'un module de dosage du carbone organique; un Rock-Eval III (Oil Show Analyzer qui se distingue du précédent par le fait qu'il analyse séparément le gaz et l'huile et qu'il effectue le dosage du carbone organique à la place du pic S3. En ce qui concerne l'interprétation de la méthode, l'expérience acquise tant par les applications aux bassins sédimentaires que par les études expérimentales menées en laboratoire a permis de mieux connaître les paramètres utilisés (pics S1, S2, S3, température de pyrolyse Tmax à travers leurs variations et, de là, de mieux discerner les limites d'application de la méthode. En ce qui concerne l'application de la méthode, la représentation verticale des résultats sous forme de logs géochimiques conduit à une interprétation à la fois efficace et pratique. Des abaques et des diagrammes de référence permettent de caractériser les roches mères (potentiels pétroliers, types de matière organique, degré d'évolution, altérations . . . ainsi que les phénomènes de migration. L'établissement de cartes géochimiques à l'échelle du bassin devient alors possible. Enfin la méthode est sortie du domaine de l'exploration pétrolière proprement dite pour trouver des applications à l'étude des charbons, des roches bitumineuses, des sédiments récents et même aux

La pyrolyse Rock-Eval et ses applications. Première partie. Rock-Eval Pyrolysis and Its Applications (Part One

Directory of Open Access Journals (Sweden)

Espitalie J.

2006-11-01

Full Text Available Conçue pour répondre aux besoins de l'exploration pétrolière, la méthode de pyrolyse Rock-Eval est maintenant largement utilisée. Elle fournit, en effet, et d'une façon rapide, différentes informations sur le contenu organique des roches, telles que le potentiel pétrolier des séries rencontrées, la nature des kérogènes, leur état de maturation. En ce qui concerne le matériel, deux nouvelles versions ont été mises au point à l'Institut Français du Pétrole (IFP depuis l'apparition en 1977 des premiers appareils Rock-Eval : un Rock-Eval II complètement automatisé grâce à un microprocesseur et doté, en option, d'un module de dosage du carbone organique; un Rock-Eval III (Oil Show Analyzer qui se distingue du précédent par le fait qu'il analyse séparément le gaz et l'huile et qu'il effectue le dosage du carbone organique à la place du pic S3. En ce qui concerne l'interprétation de la méthode, l'expérience acquise tant par les applications aux bassins sédimentaires que par les études expérimentales menées en laboratoire a permis de mieux connaître les paramètres utilisés (pics S1, S2, S3, température de pyrolyse Tmax à travers leurs variations et, de là, de mieux discerner les limites d'application de la méthode. En ce qui concerne l'application de la méthode, la représentation verticale des résultats sous forme de logs géochimiques conduit à une interprétation à la fois efficace et pratique. Des abaques et des diagrammes de référence permettent de caractériser les roches mères (potentiels pétroliers, types de matière organique, degré d'évolution, altérations. . . ainsi que les phénomènes de migration. L'établissement de cartes géochimiques à l'échelle du bassin devient alors possible. Enfin la méthode est sortie du domaine de l'exploration pétrolière proprement dite pour trouver des applications à l'étude des charbons, des roches bitumineuses, des sédiments récents et même aux

La pyrolyse Rock-Eval et ses applications. Deuxième partie. Rock-Eval Pyrolysis and Its Applications (Part Two

Directory of Open Access Journals (Sweden)

Espitalie J.

2006-11-01

Full Text Available Conçue pour répondre aux besoins de l'exploration pétrolière, la méthode de pyrolyse Rock-Eval est maintenant largement utilisée. Elle fournit, en effet, et d'une façon rapide, différentes informations sur le contenu organique des roches, telles que le potentiel pétrolier des séries rencontrées, la nature des kérogènes, leur état de maturation. En ce qui concerne le matériel, deux nouvelles versions ont été mises au point à l'Institut Français du Pétrole (IFP depuis l'apparition en 1977 des premiers appareils Rock-Eval : un Rock-Eval II complètement automatisé grâce à un microprocesseur et doté, en option, d'un module de dosage du carbone organique; un Rock-Eval III (Oil Show Analyzer qui se distingue du précédent par le fait qu'il analyse séparément le gaz et l'huile et qu'il effectue le dosage du carbone organique à la place du pic S3. En ce qui concerne l'interprétation de la méthode, l'expérience acquise tant par les applications aux bassins sédimentaires que par les études expérimentales menées en laboratoire a permis de mieux connaître les paramètres utilisés (pics S1, S2, S3, température de pyrolyse Tmax à travers leurs variations et, de là, de mieux discerner les limites d'application de la méthode. En ce qui concerne l'application de la méthode, la représentation verticale des résultats sous forme de logs géochimiques conduit à une interprétation à la fois efficace et pratique. Des abaques et des diagrammes de référence permettent de caractériser les roches mères (potentiels pétroliers, types de matière organique, degré d'évolution, altérations. . . ainsi que les phénomènes de migration. L'établissement de cartes géochimiques à l'échelle du bassin devient alors possible. Enfin la méthode est sortie du domaine de l'exploration pétrolière proprement dite pour trouver des applications à l'étude des charbons, des roches bitumineuses, des sédiments récents et même aux

Maturity In The Petrochemical Industry Features, Motives And Combating

International Nuclear Information System (INIS)

Farag, H.; El Messirie, A.

2004-01-01

Petrochemicals give the highest value from crude oil and natural gas but suffers from maturity like any other business. Petrochemicals companies are promoting their business in the direction from oil and gas commodities. Specialities and life science. Reasons of maturity are expired patents, low demand, over capacity, intense competition. Actions to combat maturity are to restructure capacity achieving mega sizes, do downstream, and restructuring business practices. Strategies followed by some companies to combat maturity include exit, focus on core business and exploit a competitive advantage

17,21-Secohopanoic acids, 25-norhopanoic acids, and 28-norhopanoic acids in source rocks and crude oils

Energy Technology Data Exchange (ETDEWEB)

Xueming Pan; Philp, R.P. [University of Oklahoma, Norman, OK (United States). School of Geology and Geophysics

2006-09-15

The presence of three families of hopanoic acids, 17,21-secohopanoic acids, 25-norhopanoic acids, and 28-norhopanoic acids, is discussed. Oils from West Siberia and tar balls from the Seychelles Islands were found to contain relatively high proportions of 17,21-secohopanoic acids. These acids have not been previously reported in any oils or source rocks. A heavily biodegraded West Siberian oil, was found to contain an homologous series of 25-norhopanoic acids co-occurring with the 25-norhopanes as previously reported in only a small number of oils from Campos Basin, Brazil. 28-Norhopanoic acids have been reported in various sediments and extracts of the Monterey Shale, but in this study their occurrence has been extended to oils, degraded oils, and tar balls sourced from the Monterey Shale. The primary purpose herein is to report the occurrence of these acids and possible relationships between the acids and corresponding hydrocarbons. (Author)

Low-maturity Kulthieth Formation coal: A possible source of polycyclic aromatic hydrocarbons in benthic sediment of the northern Gulf of Alaska

Science.gov (United States)

Van Kooten, G. K.; Short, J.W.; Kolak, J.J.

2002-01-01

The successful application of forensic geology to contamination studies involving natural systems requires identification of appropriate endmembers and an understanding of the geologic setting and processes affecting the systems. Studies attempting to delineate the background, or natural, source for hydrocarbon contamination in Gulf of Alaska (GOA) benthic sediments have invoked a number of potential sources, including seep oils, source rocks, and coal. Oil seeps have subsequently been questioned as significant sources of hydrocarbons present in benthic sediments of the GOA in part because the pattern of relative polycyclic aromatic hydrocarbon (PAH) abundance characteristic of benthic GOA sediments is inconsistent with patterns typical of weathered seep oils. Likewise, native coal has been dismissed in part because ratios of labile hydrocarbons to total organic carbon (e.g. PAH:TOC) for Bering River coal field (BRCF) sources are too low - i.e. the coals are over mature - to be consistent with GOA sediments. We present evidence here that native coal may have been prematurely dismissed, because BRCF coals do not adequately represent the geochemical signatures of coals elsewhere in the Kulthieth Formation. Contrary to previous thought, Kulthieth Formation coals east of the BRCF have much higher PAH: TOC ratios, and the patterns of labile hydrocarbons in these low thermal maturity coals suggest a possible genetic relationship between Kulthieth Formation coals and nearby oil seeps on the Sullivan anticline. Analyses of low-maturity Kulthieth Formation coal indicate the low maturity coal is a significant source of PAH. Source apportionment models that neglect this source will underestimate the contribution of native coals to the regional background hydrocarbon signature. ?? Published by Elsevier Science Ltd. on behalf of AEHS.

Effects of olive maturation and stoning on quality indices and antioxidant content of extra virgin oils (cv. Coratina) during storage.

Science.gov (United States)

Gambacorta, G; Faccia, M; Previtali, M A; Pati, S; La Notte, E; Baiano, A

2010-04-01

Quality indices, antioxidant compounds, and antioxidant activities of extra-virgin oils from Coratina olives were evaluated during a 12-mo storage. Whole and stoned olives, picked at 2 different maturation index (MI), were submitted to malaxation for 45 min and extracted by a 3-phase continuous system. A 90-min malaxation trial was also performed for the stoned olives. The following parameters were monitored: free acidity, peroxide value, K(232) and K(270) indices, sensory profile, total phenolic content (TPC), phenolic profiles, tocopherol compounds, and antioxidant activity (AA). The highest TPC, AA, and sensory score were found for the oils obtained by olives picked at low MI and by stoned olives. After 12 mo, all the oils were still included into the "extra-virgin" category, and those deriving from whole olives picked at the lowest MI showed the best sensory characteristics due to high fruity and well-balanced pungent and bitter tastes. This study could represent a helpful tool for oil-makers to improve the marketing of extra-virgin olive oils produced from cultivars with very high phenolic contents, such as Coratina, generally not adequately appreciated by consumers because of their excessive bitterness and pungent taste. These oils, when extracted from whole olives, are generally consumed after a certain period of time (at least 6 mo) during which a decrease in the phenolic content occurs. The results of the present work demonstrate that oils extracted from olives picked at low maturation index can be marketed immediately after production if subjected to stoning and malaxed for a short time. This procedure allows to adjust the phenolic content and to obtain a high flavor and a well-balanced taste.

Advancement in application of diamondoids on organic geochemistry

Directory of Open Access Journals (Sweden)

Anlai Ma

2016-08-01

Full Text Available Diamondoids occur in all kinds of fossil fuels. Due to peculiar cage molecular structures, diamondoids have been widely used in the maturity assessment of high mature to over-mature oils as well as source rocks since the 1990s. New advancements in maturity, oil-cracking, oil mixing, oil biodegradation, organic facies, TSR, gas washing, migration, and oil spill identification using diamondoids during the 21st century will be further discussed in this paper; the origin and possible forming mechanisms of diamondoids are also explained. Owing to the vagueness of the origin of diamondoid, the results of the maturity and oil cracking among researchers brought about great differences. It is suggested that the research of the evolution of diamondoid in different type oils and source rocks are beneficial when applied in organic geochemistry, especially for the depth limits for the deep reservoirs.

Thermal-maturity limit for primary thermogenic-gas generation from humic coals as determined by hydrous pyrolysis

Science.gov (United States)

Lewan, Michael; Kotarba, M.J.

2014-01-01

Hydrous-pyrolysis experiments at 360°C (680°F) for 72 h were conducted on 53 humic coals representing ranks from lignite through anthracite to determine the upper maturity limit for hydrocarbon-gas generation from their kerogen and associated bitumen (i.e., primary gas generation). These experimental conditions are below those needed for oil cracking to ensure that generated gas was not derived from the decomposition of expelled oil generated from some of the coals (i.e., secondary gas generation). Experimental results showed that generation of hydrocarbon gas ends before a vitrinite reflectance of 2.0%. This reflectance is equivalent to Rock-Eval maximum-yield temperature and hydrogen indices (HIs) of 555°C (1031°F) and 35 mg/g total organic carbon (TOC), respectively. At these maturity levels, essentially no soluble bitumen is present in the coals before or after hydrous pyrolysis. The equivalent kerogen atomic H/C ratio is 0.50 at the primary gas-generation limit and indicates that no alkyl moieties are remaining to source hydrocarbon gases. The convergence of atomic H/C ratios of type-II and -I kerogen to this same value at a reflectance of indicates that the primary gas-generation limits for humic coal and type-III kerogen also apply to oil-prone kerogen. Although gas generation from source rocks does not exceed vitrinite reflectance values greater than , trapped hydrocarbon gases can remain stable at higher reflectance values. Distinguishing trapped gas from generated gas in hydrous-pyrolysis experiments is readily determined by of the hydrocarbon gases when a -depleted water is used in the experiments. Water serves as a source of hydrogen in hydrous pyrolysis and, as a result, the use of -depleted water is reflected in the generated gases but not pre-existing trapped gases.

Source rock potential of middle cretaceous rocks in Southwestern Montana

Science.gov (United States)

Dyman, T.S.; Palacas, J.G.; Tysdal, R.G.; Perry, W.J.; Pawlewicz, M.J.

1996-01-01

The middle Cretaceous in southwestern Montana is composed of a marine and nonmarine succession of predominantly clastic rocks that were deposited along the western margin of the Western Interior Seaway. In places, middle Cretaceous rocks contain appreciable total organic carbon (TOC), such as 5.59% for the Mowry Shale and 8.11% for the Frontier Formation in the Madison Range. Most samples, however, exhibit less than 1.0% TOC. The genetic or hydrocarbon potential (S1+S2) of all the samples analyzed, except one, yield less than 1 mg HC/g rock, strongly indicating poor potential for generating commercial amounts of hydrocarbons. Out of 51 samples analyzed, only one (a Thermopolis Shale sample from the Snowcrest Range) showed a moderate petroleum potential of 3.1 mg HC/g rock. Most of the middle Cretaceous samples are thermally immature to marginally mature, with vitrinite reflectance ranging from about 0.4 to 0.6% Ro. Maturity is high in the Pioneer Mountains, where vitrinite reflectance averages 3.4% Ro, and at Big Sky Montana, where vitrinite reflectance averages 2.5% Ro. At both localities, high Ro values are due to local heat sources, such as the Pioneer batholith in the Pioneer Mountains.

Mineralogical, chemical and K-Ar isotopic changes in Kreyenhagen Shale whole rocks and <2 µm clay fractions during natural burial and hydrous-pyrolysis experimental maturation

Science.gov (United States)

Clauer, Norbert; Lewan, Michael D.; Dolan, Michael P.; Chaudhuri, Sambhudas; Curtis, John B.

2014-01-01

Progressive maturation of the Eocene Kreyenhagen Shale from the San Joaquin Basin of California was studied by combining mineralogical and chemical analyses with K–Ar dating of whole rocks and sequence, indicating that there is no detectable variation in the crystallo-chemical organization of the K-bearing alumino-silicates with depth. No supply of K from outside of the rock volumes occurred, which indicates a closed-system behavior for it. Conversely, the content of the total organic carbon (TOC) content decreases significantly with burial, based on the progressive increasing Al/TOC ratio of the whole rocks. The initial varied mineralogy and chemistry of the rocks and their <2 μm fractions resulting from differences in detrital sources and depositional settings give scattered results that homogenize progressively during burial due to increased authigenesis, and concomitant increased alteration of the detrital material.

Improved recovery potential in mature heavy oil fields by Alkali-surfactant flooding

Energy Technology Data Exchange (ETDEWEB)

Bryan, J.; Kantzas, A. [Calgary Univ., AB (Canada). Tomographic Imaging and Porous Media Laboratory

2008-10-15

Primary and secondary alkali surfactant (AS) chemical flooding techniques were optimized in this study. Core flooding experiments were conducted in order to investigate the formation of emulsions in bulk liquid system due to flow through rock pores. Cores were dried and then saturated with water or brine in order to measure permeability. The floods were then performed at various injection rates followed by the AS solution. Solutions were also injected without previous waterflooding. Individual oil and water mobilities were then calculated using the experimental data. Individual phase mobilities were calculated using the total pressure gradient measured across the core. Nuclear magnetic resonance (NMR) studies were conducted in order to determine emulsion formation within porous media from in situ flooding tests at 4 different locations. Data from the NMR studies were used to calculate fluid distributions and measurements of in situ emulsification during the chemical floods. The study demonstrated that the use of the surfactants resulted in the in situ formation of oil-water and water-oil emulsions. Responses from de-ionized alkali and brine AS systems were similar. The recovery mechanism blocked off water channels and provided improved sweep efficiency in the core. It was concluded that injection rates and pressure gradients for chemical floods should be lowered in order to optimize their efficiency. 26 refs., 6 tabs., 15 figs.

Modeling tectonic heat flow and source rock maturity in the Rub' Al-Khali Basin (Saudi Arabia), with the help of GOCE satellite gravity data

NARCIS (Netherlands)

Abdul Fattah, R.; Meekes, S.; Bouman, J.; Ebbing, J.; Haagmans, R.

2014-01-01

A 3D basin modeling study was carried out to reconstruct the regional heat flow and source rock maturity in the Rub'al-Khali basin. Gravity gradient data from the GOCE satellite were used to model deep structures, such as the Moho interface. Tectonic heat flow was modeled using the GOCE-based Moho

Thermal maturity and petroleum kitchen areas of Liassic Black Shales (Lower Jurassic) in the central Upper Rhine Graben, Germany

Science.gov (United States)

Böcker, Johannes; Littke, Ralf

2016-03-01

In the central Upper Rhine Graben (URG), several major oil fields have been sourced by Liassic Black Shales. In particular, the Posidonia Shale (Lias ɛ, Lower Toarcian) acts as excellent and most prominent source rock in the central URG. This study is the first comprehensive synthesis of Liassic maturity data in the URG area and SW Germany. The thermal maturity of the Liassic Black Shales has been analysed by vitrinite reflectance (VRr) measurements, which have been verified with T max and spore coloration index (SCI) data. In outcrops and shallow wells (oil window (ca. 0.50-0.60 % VRr). This maturity is found in Liassic outcrops and shallow wells in the entire URG area and surrounding Swabian Jura Mountains. Maximum temperatures of the Posidonia Shale before graben formation are in the order of 80-90 °C. These values were likely reached during Late Cretaceous times due to significant Upper Jurassic and minor Cretaceous deposition and influenced by higher heat flows of the beginning rift event at about 70 Ma. In this regard, the consistent regional maturity data (VRr, T max, SCI) of 0.5-0.6 % VRr for the Posidonia Shale close to surface suggest a major burial-controlled maturation before graben formation. These consistent maturity data for Liassic outcrops and shallow wells imply no significant oil generation and expulsion from the Posidonia Shale before formation of the URG. A detailed VRr map has been created using VRr values of 31 wells and outcrops with a structure map of the Posidonia Shale as reference map for a depth-dependent gridding operation. Highest maturity levels occur in the area of the Rastatt Trough (ca. 1.5 % VRr) and along the graben axis with partly very high VRr gradients (e.g. well Scheibenhardt 2). In these deep graben areas, the maximum temperatures which were reached during upper Oligocene to Miocene times greatly exceed those during the Cretaceous.

Short wavelength Raman spectroscopy applied to the discrimination and characterization of three cultivars of extra virgin olive oils in different maturation stages.

Science.gov (United States)

Gouvinhas, Irene; Machado, Nelson; Carvalho, Teresa; de Almeida, José M M M; Barros, Ana I R N A

2015-01-01

Extra virgin olive oils produced from three cultivars on different maturation stages were characterized using Raman spectroscopy. Chemometric methods (principal component analysis, discriminant analysis, principal component regression and partial least squares regression) applied to Raman spectral data were utilized to evaluate and quantify the statistical differences between cultivars and their ripening process. The models for predicting the peroxide value and free acidity of olive oils showed good calibration and prediction values and presented high coefficients of determination (>0.933). Both the R(2), and the correlation equations between the measured chemical parameters, and the values predicted by each approach are presented; these comprehend both PCR and PLS, used to assess SNV normalized Raman data, as well as first and second derivative of the spectra. This study demonstrates that a combination of Raman spectroscopy with multivariate analysis methods can be useful to predict rapidly olive oil chemical characteristics during the maturation process. Copyright © 2014 Elsevier B.V. All rights reserved.

Organic compositions of lacustrine source rocks in Jiyang super-depression and its implication to petroleum geology

Institute of Scientific and Technical Information of China (English)

无

2006-01-01

The compositions of organic matter in four immature source rocks from Tertiary strata of Jiyang super-depression, the most typical continental rift subsidence basin in East China, have been studied by different extracting methods with CHCl3, MAC and CS2/NMP, respectively. The results suggest that there are great differences among the chemical compositions of organic matter in the source rocks derived from different depositional environments. About 79% of all the organic matter exists by non- covalent bond in the Es4 source rocks which were deposited under the saline lacustrine, indicating that its organic matter is not the real kerogen, but mainly composed of soluble organic matter which is easy to generate hydrocarbon at lower temperature. This is why the immature oils were derived from Es4 source rocks in Dongying depression. In contrast, around 60% of organic matter exists by covalent bond in Es3 source rocks which were deposited under the deep brackish-fresh lacustrine, showing that Es3 source rocks are mainly composed of kerogen producing mature hydrocarbon at higher temperature. The thermal simulation experiments, upon the remaining solid source rocks which were sequentially extracted by the three solvents, have been carried out. The chloroform extracts from the simulation product have been compared with the other three solvent extracts gained at room temperature. It is obvious that remarkable odd/even predominance (OEP) is mainly the characteristic of soluble organic matter; phytane mostly exists in the soluble organic matter by means of non-covalent bonds and characteristics of soluble organic matter are similar to these in immature oils produced in Jiyang super-depression.

Distribution of organic carbon and petroleum source rock potential of Cretaceous and lower Tertiary carbonates, South Florida Basin: preliminary results

Science.gov (United States)

Palacas, James George

1978-01-01

Analyses of 134 core samples from the South Florida Basin show that the carbonates of Comanchean age are relatively richer in average organic carbon (0.41 percent) than those of Coahuilan age (0.28 percent), Gulfian age (0.18 percent) and Paleocene age (0.20 percent). They are also nearly twice as rich as the average world, wide carbonate (average 0.24 percent). The majority of carbonates have organic carbons less than 0.30 percent but the presence of many relatively organic rich beds composed of highly bituminous, argillaceous, highly stylolitic, and algal-bearing limestones and dolomites accounts for the higher percentage of organic carbon in some of the stratigraphic units. Carbonate rocks that contain greater than 0.4 percent organic carbon and that might be considered as possible petroleum sources were noted in almost each subdivision of the Coahuilan and Comanchean Series but particularly the units of Fredericksburg 'B', Trinity 'A', Trinity 'F', and Upper Sunniland. Possible source rocks have been ascribed by others to the Lower Sunniland, but lack of sufficient samples precluded any firm assessment in this initial report. In the shallower section of the basin, organic-rich carbonates containing as much as 3.2 percent organic carbon were observed in the lowermost part of the Gulfian Series and carbonate rocks with oil staining or 'dead' and 'live oil' were noted by others in the uppermost Gulfian and upper Cedar Keys Formation. It is questionable whether these shallower rocks are of sufficient thermal maturity to have generated commercial oil. The South Florida basin is still sparsely drilled and produces only from the Sunniland Limestone at an average depth of 11,500 feet (3500 m). Because the Sunniland contains good reservoir rocks and apparently adequate source rocks, and because the success rate of new oil field discoveries has increased in recent years, the chances of finding additional oil reserves in the Sunniland are promising. Furthermore, the

Source rock hydrocarbons. Present status

International Nuclear Information System (INIS)

Vially, R.; Maisonnier, G.; Rouaud, T.

2013-01-01

This report first presents the characteristics of conventional oil and gas system, and the classification of liquid and gaseous non conventional hydrocarbons, with the peculiar case of coal-bed methane. The authors then describe how source rock hydrocarbons are produced: production of shale oils and gases (horizontal drilling, hydraulic fracturing, exploitation) and of coal-bed methane and coal mine methane. In the next part, they address and discuss the environmental impact of source rock hydrocarbon production: installation footprint, water resource management, drilling fluids, fracturing fluids composition, toxicity and recycling, air pollution, induced seismicity, pollutions from other exploitation and production activities. They propose an overview of the exploitation and production of source rock gas, coal-bed gas and other non conventional gases in the world. They describe the current development and discuss their economic impacts: world oil context and trends in the USA, in Canada and other countries, impacts on the North American market, on the world oil industry, on refining industries, on the world oil balance. They analyse the economic impacts of non conventional gases: development potential, stakes for the world gas trade, consequence for gas prices, development opportunities for oil companies and for the transport sector, impact on CO 2 emissions, macro-economic impact in the case of the USA

Pore Scale Investigation of Wettability Alteration Through Chemically-Tuned Waterflooding in Oil-Wet Carbonate Rocks Using X-Ray Micro-Ct Imaging

Science.gov (United States)

Tawfik, M. S.; Karpyn, Z.

2017-12-01

Carbonate reservoirs host more than half of the remaining oil reserves worldwide. Due to their complex pore structure and intermediate to oil-wet nature, it is challenging to produce the remaining oil from these formations. For two decades, chemically tuned waterflooding (CTWF) has gained the attention of many researchers. Experimental, numerical, and field studies suggest that changes in ion composition of injected brine can increase oil recovery in carbonate reservoirs via wettability alteration. However, previous studies explaining the improvement in oil recovery by wettability alteration deduce wettability based on indirect measurements, including sessile drop contact angle measurements on polished rocks, relative permeability, chromatographic separation of SCN- and potential determining ions (PDIs), etc. CTWF literature offers no direct measurement of wettability alteration at the pore scale. This study proposes a direct pore-scale measurement of changes in interfacial curvatures before and after CTWF. Micro-coreflood experiments are performed to investigate the effect of injection brine salinity, ion composition and temperature on rock wettability at the pore scale. X-ray micro-CT scanning is used to obtain 3D image sets to calculate in-situ contact angle distributions. The study also aims to find a correlation between the magnitude of improvement in oil recovery at the macro-scale and the corresponding contact angle distribution at the pore-scale at different experimental conditions. Hence, macro-scale coreflood experiments are performed using the same conditions as the micro-corefloods. Macro-scale coreflood experiments have shown that brines with higher concentration of Ca2+, Mg2+ and SO42- ions have higher recoveries compared to standard seawater. This translates to wettability alteration into a more intermediate-wet state. This study enhances the understanding of the pore-scale physico-chemical mechanisms controlling wettability alteration via CTWF

The role of nitrogen and sulphur bearing compounds in the wettability of oil reservoir rocks: an approach with nuclear microanalysis and other related surface techniques

International Nuclear Information System (INIS)

Mercier, F.; Toulhoat, N.; Potocek, V.; Trocellier, P.

1999-01-01

Oil recovery is strongly influenced by the wettability of the reservoir rock. Some constituents of the crude oil (polar compounds and heavy fractions such as asphaltenes with heteroatoms) are believed to react with the reservoir rock and to condition the local wettability. Therefore, it is important to obtain as much knowledge as possible about the characteristics of the organic matter/mineral interactions. This study is devoted to the description at the microscopic scale of the distribution of some heavy fractions of crude oil (asphaltenes) and nitrogen molecules (pyridine and pyrrole) on model minerals of sandstone reservoir rocks such as silica and clays. Nuclear microanalysis, X-Ray Photoelectron Spectroscopy and other related microscopic imaging techniques allow to study the distribution and thickness of the organic films. The respective influences of the nature of the mineral substrate and the organic matter are studied. The important role played by the nitrogen compounds in the adsorption of organic matter is emphasized

Characteristics of source rocks of the Datangpo Fm, Nanhua System, at the southeastern margin of Sichuan Basin and their significance to oil and gas exploration

Directory of Open Access Journals (Sweden)

Zengye Xie

2017-11-01

Full Text Available In recent years, much attention has been paid to the development environment, biogenetic compositions and hydrocarbon generation characteristics of ancient source rocks in the deep strata of the Sichuan Basin because oil and gas exploration extends continuously to the deep and ultra-deep strata and a giant gas field with the explored reserves of more than 1 × 1012 m3 was discovered in the Middle and Upper Proterozoic–Lower Paleozoic strata in the stable inherited paleo-uplift of the central Sichuan Basin. Based on the previous geological research results, outcrop section of the Datangpo Fm, Nanhua System, at the southeastern margin of the Sichuan Basin was observed and the samples taken from the source rocks were tested and analyzed in terms of their organic geochemistry and organic petrology. It is shown that high-quality black shale source rocks of the Datangpo Fm are developed in the tensional background at the southeastern margin of the Sichuan Basin between two glacial ages, i.e., Gucheng and Nantuo ages in the Nanhua Period. Their thickness is 16–180 m and mineral compositions are mainly clay minerals and clastic quartz. Besides, shale in the Datangpo Fm is of high-quality sapropel type source rock with high abundance at an over-mature stage, and it is characterized by low pristane/phytane ratios (0.32–0.83, low gammacerane abundance, high-abundance tricyclic terpane and higher-content C27 and C29 gonane, indicating that biogenetic compositions are mainly algae and microbes in a strong reducing environment with low salinity. It is concluded that the Datangpo Fm source rocks may be developed in the rift of Nanhua System in central Sichuan Basin. Paleo-uplifts and paleo-slopes before the Caledonian are the favorable locations for the accumulation of dispersed liquid hydrocarbons and paleo-reservoirs derived from the Datangpo Fm source rocks. In addition, scale accumulation zones of dispersed organic matter cracking gas and paleo

Triassic oils and related hydrocarbon kitchens in the Adriatic basin

Energy Technology Data Exchange (ETDEWEB)

Novelli, L.; Demaison, G. (AGIP, Milan (Italy))

1988-08-01

Without exception, the oils from both the Abruzzi basin and Albanian foredeep are of lower Liassic to Upper Triassic origin. This is demonstrated by biological marker-based correlations between the oils and stratigraphically controlled, carbonate-rich source rocks. The biomarker studies also provided proof to conclude that many of the oils possess low API gravities and high sulfur contents because they are immature rather than biodegraded. Following the geochemical investigations, a computer-aided, basinwise maturation simulation of the hydrocarbon kitchens was carried out, with backstripping in geologic time. The simulations, performed with the Tissot-Espitalie kinetic model, used basin-specific kerogen activation energies obtained by the optimum method. These simulated values were calibrated with observed values in deep wells. Two characteristics diverge from normal petroleum basin situations (e.g., the North Sea basin): sulfur-rich kerogens in the source rocks, featuring relatively low activation energy distributions, and low geothermal gradients in the subsurface. The geographic outlines of simulated Triassic-lower Liassic hydrocarbon kitchens closely coincide with the zones of petroleum occurrence and production in the Adriatic basin. Furthermore, API gravities of the oils are broadly predicted by the mathematical simulations. This methodology has once again shown its ability to rationally high-grade the petroleum-rich sectors of sedimentary basin while identifying those areas where chances of success are extremely low regardless of the presence of structures.

Fission track analysis and evolution of mesozoic-paleozoic hydrocarbon resource-rocks headed in Northern Jiangsu-South Yellow sea basin

International Nuclear Information System (INIS)

Xu Hong; Cai Qianzhong; Sun Heqing; Guo Zhenxuan; Yan Guijing; Dai Jing; Liu Dongying

2008-01-01

Fission track data of different geologic epoches from Binhai salient, Yancheng sag, Haian sag, Baiju sag, Gaoyou sag, Hongze sag and Jinhu sag of northern Jiangsu basin and seismic data from Laoshan uplift in South Yellow Sea basin and evolution of Paleozoic hydrocarbon resource-rocks headed in the Northern Jiangsu-South Yellow Sea basin were studied. Results indicate that Binhai salient uplifted in 38-15 Ma, forming 'structure uplifting model', Paleozoic hydrocarbon resource-rocks have the appearance of 'different layers but identical mature, different layers but identical temperature' with Laoshan uplift. All sags have the characters of 'long time heating model', and sedimentations in Cenozoic were exploited by 2 km. Mesozoic-Paleozoic hydrocarbon resource- rocks of Laoshan uplift get ahead of 10 km. Structure evolution was compared with Binhai salient. According to the modeling results of secondary hydrocarbon generation, Mesozoic-Paleozoic hydrocarbon resource-rocks of Laoshan uplift have the good reservoir potentiality and probably become an important new window for sea oil and gas exploration. (authors)

ISS Assessment of the Influence of Nonpore Surface in the XPS Analysis of Oil-Producing Reservoir Rocks

Science.gov (United States)

Leon; Toledo; Araujo

1997-08-15

The application of X-ray photoelectron spectroscopy (XPS) to oil-producing reservoir rocks is new and has shown that pore surface concentrations can be related to rock wettability. In the preparation of fresh fractures of rocks, however, some nonpore surface corresponding to the connection regions in the rocks is created and exposed to XPS. To assess the potential influence of this nonpore surface in the XPS analysis of rocks here we use ion scattering spectroscopy (ISS), which has a resolution comparable to the size of the pores, higher than that of XPS, with an ion gun of He+ at maximum focus. Sample charging effects are partially eliminated with a flood gun of low energy electrons. All the ISS signals are identified by means of a formula which corrects any residual charging on the samples. Three rock samples are analyzed by XPS and ISS. The almost unchanged ISS spectra obtained at different points of a given sample suggest that the nonpore surface created in the fracture process is negligibly small, indicating that XPS data, from a larger surface spot, represents the composition of true pore surfaces. The significant changes observed in ISS spectra from different samples indicate that ISS is sample specific. Copyright 1997Academic Press

Studies of electrical properties of low-resistivity sandstones based on digital rock technology

Science.gov (United States)

Yan, Weichao; Sun, Jianmeng; Zhang, Jinyan; Yuan, Weiguo; Zhang, Li; Cui, Likai; Dong, Huaimin

2018-02-01

Electrical properties are important parameters to quantitatively calculate water saturation in oil and gas reservoirs by well logging interpretation. It is usual that oil layers show high resistivity responses, while water layers show low-resistivity responses. However, there are low-resistivity oil zones that exist in many oilfields around the world, leading to difficulties for reservoir evaluation. In our research, we used digital rock technology to study different internal and external factors to account for low rock resistivity responses in oil layers. We first constructed three-dimensional digital rock models with five components based on micro-computed tomography technology and x-ray diffraction experimental results, and then oil and water distributions in pores were determined by the pore morphology method. When the resistivity of each component was assigned, rock resistivities were calculated by using the finite element method. We collected 20 sandstone samples to prove the effectiveness of our numerical simulation methods. Based on the control variate method, we studied the effects of different factors on the resistivity indexes and rock resistivities. After sensitivity analyses, we found the main factors which caused low rock resistivities in oil layers. For unfractured rocks, influential factors arranged in descending order of importance were porosity, clay content, temperature, water salinity, heavy mineral, clay type and wettability. In addition, we found that the resistivity index could not provide enough information to identify a low-resistivity oil zone by using laboratory rock-electric experimental results. These results can not only expand our understandings of the electrical properties of low-resistivity rocks from oil layers, but also help identify low-resistivity oil zones better.

On the feasibility of inducing oil mobilization in existing reservoirs via wellbore harmonic fluid action

KAUST Repository

Jeong, Chanseok

2011-03-01

Although vibration-based mobilization of oil remaining in mature reservoirs is a promising low-cost method of enhanced oil recovery (EOR), research on its applicability at the reservoir scale is still at an early stage. In this paper, we use simplified models to study the potential for oil mobilization in homogeneous and fractured reservoirs, when harmonically oscillating fluids are injected/produced within a well. To this end, we investigate first whether waves, induced by fluid pressure oscillations at the well site, and propagating radially and away from the source in a homogeneous reservoir, could lead to oil droplet mobilization in the reservoir pore-space. We discuss both the fluid pore-pressure wave and the matrix elastic wave cases, as potential agents for increasing oil mobility. We then discuss the more realistic case of a fractured reservoir, where we study the fluid pore-pressure wave motion, while taking into account the leakage effect on the fracture wall. Numerical results show that, in homogeneous reservoirs, the rock-stress wave is a better energy-delivery agent than the fluid pore-pressure wave. However, neither the rock-stress wave nor the pore-pressure wave is likely to result in any significant residual oil mobilization at the reservoir scale. On the other hand, enhanced oil production from the fractured reservoir\\'s matrix zone, induced by cross-flow vibrations, appears to be feasible. In the fractured reservoir, the fluid pore-pressure wave is only weakly attenuated through the fractures, and thus could induce fluid exchange between the rock formation and the fracture space. The vibration-induced cross-flow is likely to improve the imbibition of water into the matrix zone and the expulsion of oil from it. © 2011 Elsevier B.V.

Burial history, thermal history and hydrocarbon generation modelling of the Jurassic source rocks in the basement of the Polish Carpathian Foredeep and Outer Carpathians (SE Poland)

Science.gov (United States)

Kosakowski, Paweł; Wróbel, Magdalena

2012-08-01

Burial history, thermal maturity, and timing of hydrocarbon generation were modelled for the Jurassic source rocks in the basement of the Carpathian Foredeep and marginal part of the Outer Carpathians. The area of investigation was bounded to the west by Kraków, to the east by Rzeszów. The modelling was carried out in profiles of wells: Będzienica 2, Dębica 10K, Góra Ropczycka 1K, Goleszów 5, Nawsie 1, Pławowice E1 and Pilzno 40. The organic matter, containing gas-prone Type III kerogen with an admixture of Type II kerogen, is immature or at most, early mature to 0.7 % in the vitrinite reflectance scale. The highest thermal maturity is recorded in the south-eastern part of the study area, where the Jurassic strata are buried deeper. The thermal modelling showed that the obtained organic matter maturity in the initial phase of the "oil window" is connected with the stage of the Carpathian overthrusting. The numerical modelling indicated that the onset of hydrocarbon generation from the Middle Jurassic source rocks was also connected with the Carpathian thrust belt. The peak of hydrocarbon generation took place in the orogenic stage of the overthrusting. The amount of generated hydrocarbons is generally small, which is a consequence of the low maturity and low transformation degree of kerogen. The generated hydrocarbons were not expelled from their source rock. An analysis of maturity distribution and transformation degree of the Jurassic organic matter shows that the best conditions for hydrocarbon generation occurred most probably in areas deeply buried under the Outer Carpathians. It is most probable that the "generation kitchen" should be searched for there.

Company maturity models: Application to supplier development program in oil&gas sector

Directory of Open Access Journals (Sweden)

Jabier Retegi Albisua

2018-04-01

Full Text Available Purpose: In order to achieve excellence, outsourced maintenance contractors in Oil&Gas sector play a key role due to the important impact of their task on security, availability and energy consumption. This paper presents the process followed in order to implement a Supplier Development Program in a refinery using Company Maturity Model (CoMM and the results obtained in three cases validating the method to obtain a strategic improvement project medium term grid. Design/methodology/approach: The methodology followed consists of constructing a CoMM capturing the knowledge existing in the refinery and applying it with three supplier improvement teams. Findings and conclusions have arised through an observation of the three processes and extracting common conclusions. Findings: The resulting CoMM has been used for self-assessment by three suppliers and has demonstrated its potential to define a medium-term improvement project road map validated by the customer. Furthermore, during the design and application processes, the contribution of CoMMs to the SECI process of knowledge management has been observed. Practical implications: The use of CoMMs in a service contractor context can be applied in other sectors. It contributes to alignment of targets between the supplier and customer companies and to knowledge sharing inside both firms. Originality/value: Maturity models in many transversal fields (CMMI, EFQM, BPMM, PEMM, etc. have been thoroughly studied in the literature. Less effort has been made analysing the case of using maturity models constructed and implemented by a company for its specific purposes. In this paper, the process followed by a company to establish a Supplier Development Process using CoMMs is described.

Continuous distillation of oil-bearing rocks

Energy Technology Data Exchange (ETDEWEB)

1923-11-14

A continuous process of distilling petroleum-bearing, asphaltic, or bituminous rocks to free bitumen is characterized by vaporizing hydrocarbons solid, pasty, or liquid from petroleum-containing asphaltic or bituminous rocks to free bitumen without ever reaching the temperatures at which they can produce decomposition, the necessary heat being furnished by combustion of part of the hydrocarbons of the treated rocks. A furnace for carrying out the process of claim 1 is characterized by consisting of a cavity lined inside with reflector, of variable section and with a throat at the upper part for charging the material to be treated and means for blowing the lower part of the furnace with the air necessary for combustion and inert gas for regulating the combustion and removal of the hydrocarbons.

A Study of Porphyrins in Petroleum Source Rocks

Energy Technology Data Exchange (ETDEWEB)

Huseby, Berit

1997-12-31

This thesis discusses several aspects of porphyrin geochemistry. Degradation experiments have been performed on the Messel oil shale (Eocene, Germany) to obtain information on porphyrins bound or incorporated into macromolecular structures. Thermal heating of the preextracted kerogen by hydrous pyrolysis was used to study the release of porphyrins and their temperature dependent changes during simulated diagenesis and catagenesis. Selective chemical degradation experiments were performed on the preextracted sediment to get more detailed information about porphyrins that are specifically bound to the macromolecular structures via ester bonds. From the heating experiments, in a separate study, the porphyrin nitrogen content in the generated bitumens was compared to the bulk of organic nitrogen compounds in the fraction. The bulk nitrogen contents in the generated bitumens, the water phase and the residual organic matter was recorded to establish the distribution of nitrogen between the kerogen and product phases. Porphyrins as biomarkers were examined in naturally matured Kimmeridge clay source rocks (Upper Jurassic, Norway), and the use of porphyrins as general indicators of maturity was evaluated. Underlying maturity trends in the biomarker data was investigated by Partial Least Squares analysis. Porphyrin as indicators of depositional conditions was also addressed, where the correlations between the (amounts) abundance of nickel and vanadyl porphyrins were mapped together with other descriptors that are assumed to be indicative of redox depositional conditions. 252 refs., 28 figs., 4 tabs.

A Study of Porphyrins in Petroleum Source Rocks

Energy Technology Data Exchange (ETDEWEB)

Huseby, Berit

1996-12-31

This thesis discusses several aspects of porphyrin geochemistry. Degradation experiments have been performed on the Messel oil shale (Eocene, Germany) to obtain information on porphyrins bound or incorporated into macromolecular structures. Thermal heating of the preextracted kerogen by hydrous pyrolysis was used to study the release of porphyrins and their temperature dependent changes during simulated diagenesis and catagenesis. Selective chemical degradation experiments were performed on the preextracted sediment to get more detailed information about porphyrins that are specifically bound to the macromolecular structures via ester bonds. From the heating experiments, in a separate study, the porphyrin nitrogen content in the generated bitumens was compared to the bulk of organic nitrogen compounds in the fraction. The bulk nitrogen contents in the generated bitumens, the water phase and the residual organic matter was recorded to establish the distribution of nitrogen between the kerogen and product phases. Porphyrins as biomarkers were examined in naturally matured Kimmeridge clay source rocks (Upper Jurassic, Norway), and the use of porphyrins as general indicators of maturity was evaluated. Underlying maturity trends in the biomarker data was investigated by Partial Least Squares analysis. Porphyrin as indicators of depositional conditions was also addressed, where the correlations between the (amounts) abundance of nickel and vanadyl porphyrins were mapped together with other descriptors that are assumed to be indicative of redox depositional conditions. 252 refs., 28 figs., 4 tabs.

Geochemical Aspects of Formation of Large Oil Deposits in the Volga-Ural Sedimentary Basin

Science.gov (United States)

Plotnikova, I.; Nosova, F.; Pronin, N.; Nosova, J.; Budkevich, T.

2012-04-01

The study of the rocks domanikoid type in the territory of the Ural-Volga region has an almost century-long history, beginning with the first studies of A.D. Archangelsky in the late 20's of last century. But nevertheless the question of the source of oil that formed the industrial deposits of Volga-Ural oil and gas province (OGP), where Romashkinskoye oil field occupies a special place, remains unresolved and topical. According to the sedimentary-migration theory of origin of oil and gas, it is supposed that the primary source of hydrocarbons in this area are the deposits of domanikoid type that contain a large ammount of sapropel organic matter (OM). Semiluki (domanik) horizon of srednefranski substage of the Upper Devonian is considered to be a typical domanikoid stratum. Investigation of the OM of the rocks and oils of the sedimentary cover on the basis of chromato-mass spectrometry method allows us to study the correlations between rock and oil and to assess the location (or absence) of the sources of hydrocarbons in the Paleozoic sedimentary cover. The results of geochemical study of dispersed organic matter (DOM) of rocks from Semiluksky horizon of the Upper Devonian and of the oil from Pashiysky horizon of the Middle Devonian form the basis of this paper. The objectives of this study were the following: to determine the original organic matter of the rocks, which would indicate the conditions of sedimentation of the supposed rock-oil sources; the study of chemofossils (biomarkers) in oil from Pashiyskiy horizon; and the identification of genetic association of DOM rocks from Semiluksky horizon with this oil on the basis of the oil-DOM correlation. The study of biomarkers was carried out with the help of chromato-mass spectrometry in the Laboratory of Geochemistry of Fossil Fuels (Kazan Federal University). In this study we used several informative parameters characterizing the depositional environment, the type of source OM and its maturity: STER / PENT, h

Organic Geochemistry and Rock-Eval Pyrolysis of Eocene fine Sediments, East Ketungau Basin, West Kalimantan

Directory of Open Access Journals (Sweden)

M.H. Hermiyanto Zajuli

2014-06-01

Full Text Available DOI: 10.17014/ijog.v6i2.119Indonesia contains many Paleogene and Neogene basins which some of them have been proven to be a very prolific producer of oil and gas. A study on the result of Rock-Eval pyrolysis and biomarker undertaken on the Eocene Mandai Group was able to assess hydrocarbon potential of the Paleogene fine sediments in the frontier basin, especially West Kalimantan area. East Ketungau Basin is located in the western Kalimantan, bounded with Melawi Basin by the Semitau High in the south and West Ketungau Basin in the west. The Mandai Group was deposited in the East Ketungau Basin during Eocene, consisting of sandstone and mudstone facies. Mudstone facies comprises shale, claystone, and coal. Seven samples of Eocene fine sediments collected from East Ketungau Basin were analyzed by Rock-Eval pyrolisis and three samples for biomarker to evaluate their hydrocarbon potential. The Rock-Eval pyrolisis result of Mandai Group shows that TOC value of this facies ranges from 0.34 % to 5.16 %, Potential Yield (PY between 0.06 and 4.78 mg HC/g rock, and Hydrogen Index (HI from 12 to 89. Based on that result, the fine sediments of Mandai Group are included into a gas prone source rock potential with poor to fair categories. Moreover Tmax values vary from 426o C to 451o C. The Eocene fine sediments of Mandai Group fall under kerogen type III. Based on Tmax and biomarker analyses, the maturity of the sediments is situated within immature to mature level. The fine sediments of Mandai Group were deposited in a terrestrial to marine environment under anoxic to sub-oxic condition.

Wettability modification of rock cores by fluorinated copolymer emulsion for the enhancement of gas and oil recovery

Energy Technology Data Exchange (ETDEWEB)

Feng Chunyan [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266555 (China); Kong Ying, E-mail: yingkong1967@yahoo.com.cn [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266555 (China); Jiang Guancheng [MOE Key Laboratory of Petroleum Engineering, China University of Petroleum, Beijing 102249 (China); Yang Jinrong; Pu Chunsheng [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266555 (China); Zhang Yuzhong [Key Lab of Hollow Fibre Membrane Materials and Membrane Process, Tianjin Polytechnic University, Tianjin 300160 (China)

2012-07-01

The fluorine-containing acrylate copolymer emulsion was prepared with butyl acrylate, methacrylic acid and 1H, 1H, 2H, 2H-perfluorooctyl acrylate as monomers. Moreover, the structure of the copolymer was verified by Fourier transform infrared (FTIR), nuclear magnetic resonance ({sup 1}H NMR and {sup 19}F NMR) and X-ray photoelectron spectroscopy (XPS) analyses. The results showed that all the monomers had been copolymerized and the presence of fluorine moieties. The contact angle (CA) analyses, capillary rise and imbibition spontaneous tests were used to estimate the influence of the copolymer emulsion on the wettability of gas reservoirs. It was observed that the rock surface was of large contact angles of water, oilfield sewage, hexadecane and crude oil after treatment with the emulsion. The capillary rise results indicated that the contact angles of water/air and oil/air systems increased from 60 Degree-Sign and 32 Degree-Sign to 121 Degree-Sign and 80 Degree-Sign , respectively, due to the emulsion treatment. Similarly, because of wettability alteration by the fluoropolymer, the imbibition of water and oil in rock core decreased significantly. Experimental results demonstrated that the copolymer emulsion can alter the wettability of porous media from strong liquid-wetting to gas-wetting. This work provides a cost-effective method to prepare the fluoropolymer which can increase gas deliverability by altering the wettability of gas-condensate reservoirs and mitigating the water block effect.

Regulation of mature oil fields: a constitutional analysis; Regulacao de campos maduros de petroleo: uma analise a luz da Constituicao Federal de 1988

Energy Technology Data Exchange (ETDEWEB)

Siqueira, Mariana de; Xavier, Yanko Marcius de Alencar [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

2008-07-01

The oil activities in Brazil had been started in an intensive way by the years 30 and 40. During approximately 40 years only one agent had been executed the oil activities in this country: the PETROBRAS. Many of the fields explored in the past are nowadays in decline. These fields, not interesting for the majors, would be interesting for the small and medium enterprises. The present research analyses the mature oil fields and its regulation in Brazil, looking to the 'Constituicao Federal de 1988' and to the idea of social and economic development. (author)

Discussion on the origin of sedimentary rock resistivity

International Nuclear Information System (INIS)

Dong Gangjian

2012-01-01

Conduction current way of sedimentary rock sedimentary rock is caused by the internal structure of sedimentary rock sedimentary rock pore resistance depends on the salinity of pore water and clay content and distribution. Resistivity of sedimentary rock sedimentary rock major factor in mineral composition, water resistance, oil resistance. and sedimentary structures. In practice, we should give full attention to the difference between lithology and physical properties. (author)

Microbial enhanced oil recovery and compositions therefor

Science.gov (United States)

Bryant, Rebecca S.

1990-01-01

A method is provided for microbial enhanced oil recovery, wherein a combination of microorganisms is empirically formulated based on survivability under reservoir conditions and oil recovery efficiency, such that injection of the microbial combination may be made, in the presence of essentially only nutrient solution, directly into an injection well of an oil bearing reservoir having oil present at waterflood residual oil saturation concentration. The microbial combination is capable of displacing residual oil from reservoir rock, which oil may be recovered by waterflooding without causing plugging of the reservoir rock. Further, the microorganisms are capable of being transported through the pores of the reservoir rock between said injection well and associated production wells, during waterflooding, which results in a larger area of the reservoir being covered by the oil-mobilizing microorganisms.

Petroleum systems and geologic assessment of undiscovered oil and gas, Cotton Valley group and Travis Peak-Hosston formations, East Texas basin and Louisiana-Mississippi salt basins provinces of the northern Gulf Coast region. Chapters 1-7.

Science.gov (United States)

,

2006-01-01

The purpose of the U.S. Geological Survey's (USGS) National Oil and Gas Assessment is to develop geologically based hypotheses regarding the potential for additions to oil and gas reserves in priority areas of the United States. The USGS recently completed an assessment of undiscovered oil and gas potential of the Cotton Valley Group and Travis Peak and Hosston Formations in the East Texas Basin and Louisiana-Mississippi Salt Basins Provinces in the Gulf Coast Region (USGS Provinces 5048 and 5049). The Cotton Valley Group and Travis Peak and Hosston Formations are important because of their potential for natural gas resources. This assessment is based on geologic principles and uses the total petroleum system concept. The geologic elements of a total petroleum system include hydrocarbon source rocks (source rock maturation, hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). The USGS used this geologic framework to define one total petroleum system and eight assessment units. Seven assessment units were quantitatively assessed for undiscovered oil and gas resources.

Rock engineering in Finland

Energy Technology Data Exchange (ETDEWEB)

1986-01-01

Contains a large collection of short articles concerned with tunnels and underground caverns and their construction and use. The articles are grouped under the following headings: use of the subsurface space; water supply; waste water services; energy management (includes articles on power stations, district heating and oil storage and an article on coal storage); multipurpose tunnels; waste disposal; transport; shelters; sporting and recreational amenities located in rock caverns; storage facilities; industrial, laboratory, and service facilities; rock foundations; tourism and culture; utilization of rock masses; research on the disposal of nuclear waste; training and research in the field of rock engineering; site investigation techniques; design of structures in rock; construction; the environment and occupational safety; modern equipment technology; underground space in Helsinki.

Mobility Effect on Poroelastic Seismic Signatures in Partially Saturated Rocks With Applications in Time-Lapse Monitoring of a Heavy Oil Reservoir

Science.gov (United States)

Zhao, Luanxiao; Yuan, Hemin; Yang, Jingkang; Han, De-hua; Geng, Jianhua; Zhou, Rui; Li, Hui; Yao, Qiuliang

2017-11-01

Conventional seismic analysis in partially saturated rocks normally lays emphasis on estimating pore fluid content and saturation, typically ignoring the effect of mobility, which decides the ability of fluids moving in the porous rocks. Deformation resulting from a seismic wave in heterogeneous partially saturated media can cause pore fluid pressure relaxation at mesoscopic scale, thereby making the fluid mobility inherently associated with poroelastic reflectivity. For two typical gas-brine reservoir models, with the given rock and fluid properties, the numerical analysis suggests that variations of patchy fluid saturation, fluid compressibility contrast, and acoustic stiffness of rock frame collectively affect the seismic reflection dependence on mobility. In particular, the realistic compressibility contrast of fluid patches in shallow and deep reservoir environments plays an important role in determining the reflection sensitivity to mobility. We also use a time-lapse seismic data set from a Steam-Assisted Gravity Drainage producing heavy oil reservoir to demonstrate that mobility change coupled with patchy saturation possibly leads to seismic spectral energy shifting from the baseline to monitor line. Our workflow starts from performing seismic spectral analysis on the targeted reflectivity interface. Then, on the basis of mesoscopic fluid pressure diffusion between patches of steam and heavy oil, poroelastic reflectivity modeling is conducted to understand the shift of the central frequency toward low frequencies after the steam injection. The presented results open the possibility of monitoring mobility change of a partially saturated geological formation from dissipation-related seismic attributes.

Constructive Activation of Reservoir-Resident Microbes for Enhanced Oil Recovery

Science.gov (United States)

DeBruyn, R. P.

2017-12-01

Microbial communities living in subsurface oil reservoirs biodegrade oil, producing methane. If this process could create methane within the waterflooded pore spaces of an oilfield, the methane would be expected to remain and occupy pore space, decreasing water relative permeability, diverting water flow, and increasing oil recovery by expanding the swept zone of the waterflood. This approach was tested in an oilfield in northern Montana. Preliminary assessments were made of geochemical conditions and microbiological habitations. Then, a formulation of microbial activators, with composition tailored for the reservoir's conditions, was metered at low rates into the existing injection water system for one year. In the field, the responses observed included improved oil production performance; a slight increase in injection pressure; and increased time needed for tracers to move between injection and producing wells. We interpret these results to confirm that successful stimulation of the microbial community caused more methane to be created within the swept zone of the waterflooded reservoir. When the methane exsolved as water flowed between high-pressure injection and low-pressure production wells, the bubbles occupied pore space, reducing water saturation and relative permeability, and re-directing some water flow to "slower" unswept rock with lower permeability and higher oil saturation. In total, the waterflood's swept zone had been expanded to include previously-unflooded rock. This technology was applied in this field after screening based on careful anaerobic sampling, advanced microbiological analysis, and the ongoing success of its waterflood. No reservoir or geological or geophysical simulation models were employed, and physical modifications to field facilities were minor. This technology of utilizing existing microbial populations for enhanced oil recovery can therefore be considered for deployment into waterfloods where small scale, advanced maturity, or

Shear localization in a mature mylonitic rock analog during fast slip

Science.gov (United States)

Takahashi, M.; van den Ende, M. P. A.; Niemeijer, A. R.; Spiers, C. J.

2017-02-01

Highly localized slip zones developed within ductile shear zones, such as pseudotachylyte bands occurring within mylonitic fabric rocks, are frequently interpreted as evidence for earthquake nucleation and/or propagation within the ductile regime. To understand brittle/frictional shear localization processes in ductile shear zones and to relate these to earthquake nucleation and propagation, we performed tests with large changes in velocity on a brine-saturated, 80:20 (wt %) mixture of halite and muscovite gouge after forming a mature mylonitic structure through frictional-viscous flow. The direct effect a on shear strength that occurs in response to an instantaneous upward velocity-step is an important parameter in determining the nature of seismic rupture nucleation and propagation. We obtained reproducible results regarding low-velocity mechanical behavior compared with previous work, but also obtained new insights into effects of sudden increases in slip velocity on localization and strength evolution, at velocities above a critical velocity Vc (˜20 μm/s). We found that once a ductile, mylonitic structure has developed in a shear zone, subsequent cataclastic deformation is consistently localized in a narrow zone. This switch to localized deformation is controlled by the imposed velocity and becomes most apparent at velocities above Vc. In addition, the direct effect drops rapidly when the velocity exceeds Vc. This implies that slip can accelerate toward seismic velocities almost instantly and without much loss of fracture energy, once Vc is exceeded. Obtaining a measure for Vc in natural faults is therefore of key importance for understanding earthquake nucleation and propagation in the brittle-ductile transitional regime.

Silurian and Devonian source rocks and crude oils from the western part of Libya: Organic geochemistry, palynology and carbon stratigraphy

NARCIS (Netherlands)

Elkelani, Mohamed M.A.

2015-01-01

The Early Silurian “hot” shales and Late Devonian black shales are major regional oil and gas source rocks in North Africa. Their deposition probably played a major role in global carbon cycling in general because of the large areas of the ocean affected. Comparing the Libyan δ13C record with

The upper limit of maturity of natural gas generation and its implication for the Yacheng formation in the Qiongdongnan Basin, China

Science.gov (United States)

Su, Long; Zheng, Jianjing; Chen, Guojun; Zhang, Gongcheng; Guo, Jianming; Xu, Yongchang

2012-08-01

Vitrinite reflectance (VR, Ro%) measurements from residual kerogen of pyrolysis experiments were performed on immature Maoming Oil Shale substituted the samples for the gas-prone source rocks of Yacheng formation of the Qiongdongnan Basin in the South China Sea. The work was focused on determination an upper limit of maturity for gas generation (ULMGG) or "the deadline of natural gas generation". Ro values at given temperatures increase with increasing temperature and prolonged heating time, but ΔRo-value, given a definition of the difference of all values for VR related to higher temperature and adjacent lower temperature in open-system non-isothermal experiment at the heating rate of 20 °C/min, is better than VR. And representative examples are presented in this paper. It indicates that the range of natural gas generation for Ro in the main gas generation period is from 0.96% to 2.74%, in which ΔRo is in concordance with the stage for the onset and end of the main gas generation period corresponding to 0.02% up to 0.30% and from 0.30% up to 0.80%, respectively. After the main gas generation period of 0.96-2.74%, the evolution of VR approach to the ULMGG of the whole rock for type II kerogen. It is equal to 4.38% of VR, where the gas generation rates change little with the increase of maturation, ΔRo is the maximum of 0.83% corresponding to VR of 4.38%Ro, and the source rock does not nearly occur in the end process of hydrocarbon gas generation while Ro is over 4.38%. It shows that it is the same the ULMGG from the whole rock for type II kerogen as the method with both comparison and kinetics. By comparing to both the conclusions of pyrolysis experiments and the data of VR from the source rock of Yacheng formation on a series of selected eight wells in the shallow-water continental shelf area, it indicate that the most hydrocarbon source rock is still far from reaching ULMGG from the whole rock for type II kerogen. The source rock of Yacheng formation in the

Can reserve additions in mature crude oil provinces attenuate supply-side peak oil?

Energy Technology Data Exchange (ETDEWEB)

Okullo, Samuel; Reynes, Frederic

2010-09-15

More often, oil supply has been modeled on the basis of resource availability and demand. The impact of strategy between oil producers has largely been ignored or overly simplified. In this paper, we formulate a model that embodies a weak and strong OPEC for varied rates of reserve additions. With this economic equilibrium model which has the capability to generate a supply side peak in oil production, we show that although reserves of conventional crude oil may seem abundant. OPEC has the ability to lead to substantial crude oil reserve depletion in non-OPEC countries by 2050 given likely depletion rates.

Investigation on trace elements in crude oil and organic matter extracted from rocks with instrumental neutron activation analysis

International Nuclear Information System (INIS)

Ding Zuguo; Chai Zhifang

1990-01-01

Solvent extraction, column chromatography and instrumental neutron activation analysis(INAA) have been used to investigate the trace elements in crude oil, organic matter extracted from rocks and their related fractions. With these methods, about 70 crude oil samples from eight different oil fields in China and 6 extracted asphaltene samples of the lower paleozoic from the upper Yangtze region have been analyzed, and about 40 elements of interest have been determined. Those elements include Al, As, Au, Ba, Br, Cl, Co, Cr, Cs, Cu, Fe, Hf, I, Ir, Mg, Mn, Mo, Na, Ni, Rb, Re, S, Sb, Sc, Se, Sr, Th, Zn, V and parts of REE. The experimental results show that the method possesses several advantages, i.e. non-destructive, multi-elements, sensitive, precise and accurate. Without ashing samples, the loss of volatile elements such as Cl, S, Se and Sb are avoided. The column chromatography makes it possible to study the distributions of trace elements in different fractions of crude oil and organic matter extracted. Meanwhile, the characters of trace elements in them have also been discussed

Petroleum migration and mixing in the Pearl River Mouth Basin, South China Sea

Energy Technology Data Exchange (ETDEWEB)

Chunming Zhang [Jianghan Petroleum Univ., Geochemistry Research Center, Jingzhou, Hubei (China); China Univ. of Geosciences, Dept. of Energy Resources, Beijing (China); Sitian Li [China Univ. of Geosciences, Dept. of Energy Resources, Beijing (China); Jiaming Yang [China National Offshore Oil Corp., Beijing (China); Shaokun Yang; Jianrong Wang [Nanhai East Oil Co., Research Inst., Guangzhou (China)

2004-02-01

Two oil groups have been investigated in the Pearl River Mouth Basin using their geochemical characteristics. In combination with source data, the two oil groups may be extrapolated into two end-member oils: petroleum populations A and B. The oil population A with abundant 4-methylsteranes, derived from the deeper Wenchang source rocks, migrated and accumulated earlier. The oil population B with absent 4-methylsteranes was expelled from the Enping source rocks and is associated with a relatively later phase of migration and accumulation. The two distinctive oil populations migrated updip through the marine blanket-like sandstone carriers within the Zhuhai Formation to accumulate in a series of traps along the main migration pathways at different times. Most of the accumulations are mixtures of the two end-member oils. The variations of 4-methylsterane concentrations in the accumulations can be related to the contributions from the two sources: the oils, which migrated furthest, contain greater contributions from the Wenchang source rocks, whereas those with shorter migration paths have greater contributions from the Enping sources. The later migrated oils closer to the depression areas are highly mature and the former oils in the Liuhua oil fields are of relatively low maturity, which may indicate the main migration direction along the Hui-Liu Structure Ridge (HLSR). Oils with abnormally high maturity in the middle of the HLSR may suggest oil-filling points, from which branch conduits connected the source kitchens to the main migration pathway. Oils with abnormally low maturities may reveal minor contributions from some small sags in the Dongsha Massif in a later phase. (Author)

Exploring for oil with nuclear physics

Directory of Open Access Journals (Sweden)

Mauborgne Marie-Laure

2017-01-01

Full Text Available Oil↓eld service companies help identify and assess reserves and future production for oil and gas reservoirs, by providing petrophysical information on rock formations. Some parameters of interest are the fraction of pore space in the rock, the quantity of oil or gas contained in the pores, the lithology or composition of the rock matrix, and the ease with which 'uids 'ow through the rock, i.e. its permeability. Downhole logging tools acquire various measurements based on electromagnetic, acoustic, magnetic resonance and nuclear physics to determine properties of the subsurface formation surrounding the wellbore. This introduction to nuclear measurements applied in the oil and gas industry reviews the most advanced nuclear measurements currently in use, including capture and inelastic gamma ray spectroscopy, neutron-gamma density, thermal neutron capture cross section, natural gamma ray, gamma-gamma density, and neutron porosity. A brief description of the technical challenges associated with deploying nuclear technology in the extreme environmental conditions of an oil well is also presented.

Exploring for oil with nuclear physics

Science.gov (United States)

Mauborgne, Marie-Laure; Allioli, Françoise; Stoller, Chris; Evans, Mike; Manclossi, Mauro; Nicoletti, Luisa

2017-09-01

Oil↓eld service companies help identify and assess reserves and future production for oil and gas reservoirs, by providing petrophysical information on rock formations. Some parameters of interest are the fraction of pore space in the rock, the quantity of oil or gas contained in the pores, the lithology or composition of the rock matrix, and the ease with which 'uids 'ow through the rock, i.e. its permeability. Downhole logging tools acquire various measurements based on electromagnetic, acoustic, magnetic resonance and nuclear physics to determine properties of the subsurface formation surrounding the wellbore. This introduction to nuclear measurements applied in the oil and gas industry reviews the most advanced nuclear measurements currently in use, including capture and inelastic gamma ray spectroscopy, neutron-gamma density, thermal neutron capture cross section, natural gamma ray, gamma-gamma density, and neutron porosity. A brief description of the technical challenges associated with deploying nuclear technology in the extreme environmental conditions of an oil well is also presented.

A Novel Type of Oil—generating Organic Matter —Crystal—enclosed Organic Matter

Institute of Scientific and Technical Information of China (English)

周中毅; 裴存民; 等

1992-01-01

The comparative study of organic matter in carbonate rocks and argillaceous rocks from the same horizon indicates that the organic thermal maturities of carbonate rocks are much lower than those of argillaceous rocks .Ana extensive analysis of extracted and inclused organic matter from the same sample shows that inclused organic matter is different from extracted organic matter,and the thermal maturity of the former is usually lower than that of the latter in terms of biomarker structural parameters.It seems that carbonate mineras could preserve organic matter and retard organic maturation.The inclused organic matter,abundant in most carbonate rocks,will be released from minerals and transformed into oil and gas during the high-thermal maturity stage.

Pore-scale analysis of electrical properties in thinly bedded rock using digital rock physics

International Nuclear Information System (INIS)

Sun, Jianmeng; Zhao, Jianpeng; Liu, Xuefeng; Chen, Hui; Jiang, LiMing; Zhang, JinYan

2014-01-01

We investigated the electrical properties of laminated rock consist of macro-porous layers and micro-porous layers based on digital rock technology. Due to the bedding effect and anisotropy, traditional Archie equations cannot well describe the electrical behavior of laminated rock. The RI-Sw curve of laminated rock shows a nonlinear relationship. The RI-Sw curve can be divided into two linear segments with different saturation exponent. Laminated sand-shale sequences and laminated sands of different porosity or grain size will yield macroscopic electrical anisotropy. Numerical simulation and theoretical analysis lead to the conclusion that electrical anisotropy coefficient of laminated rock is a strong function of water saturation. The function curve can be divided into three segments by the turning point. Therefore, the electrical behavior of laminated rock should be considered in oil exploration and development. (paper)

Studies on changes in patterns of fatty acids, sterols and tocopherols of oil during seed maturation of oil crops. Part I. Sunflower seeds

Directory of Open Access Journals (Sweden)

El-Shami, S. M.

1994-08-01

Full Text Available The variation of lipid constituents in maturing sunflower oil seeds has been investigated with the aim of determination of the proper harvesting time as well as the oil quality. Marked variations in fatty acid, sterol and tocopherol constituents of the oil were observed. Capillary gas chromatography and high performance liquid chromatography were used in the analysis which enabled the determination of major as well as minor constituents in the oil. In addition, gas chromatography coupled to mass spectrometry was used to confirm the structure of cycloartenol sterol. Postulations on the key compounds of fatty acids, sterols, and tocopherols were proposed in the frame of the main biosynthetic pathways. The proper harvesting time was found to be 118 days after plantation since the oil content was high and the constituents of the oil were balanced.

Se ha investigado la variación de los constituyentes lipídicos en aceites de semillas de girasol en distintos estados de maduración, con el objetivo de determinar el tiempo de recolección apropiado así como la calidad del aceite. Se observaron variaciones apreciables en los ácidos grasos, esteroles y tocoferoles del aceite. La cromatografía gaseosa capilar y la cromatografía líquida de alta eficacia se usó en el análisis que permitió la determinación tanto de los componentes mayoritarios como minoritarios en el aceite. Además, se utilizó la cromatografía gaseosa acoplada a la espectrometría de masas para confirmar la estructura del esterol cicloartenol. Se han propuesto en el marco de la ruta biosintética principal postulados sobre los compuestos clave de ácidos grasos, esteroles y tocoferoles. Se encontró como tiempo de recolección apropiado el de 118 días después de la plantación, ya que el contenido de aceite fue elevado y los constituyentes fueron equilibrados.

Compound-specific C- and H-isotope compositions of enclosed organic matter in carbonate rocks: Implications for source identification of sedimentary organic matter and paleoenvironmental reconstruction

International Nuclear Information System (INIS)

Xiong Yongqiang; Wang Yanmei; Wang Yongquan; Xu Shiping

2007-01-01

The Bohai Bay Basin is one of the most important oil-producing provinces in China. Molecular organic geochemical characteristics of Lower Paleozoic source rocks in this area have been investigated by analyzing chemical and isotopic compositions of solvent extracts and acid-released organic matter from the Lower Paleozoic carbonate rocks in the Jiyang Sub-basin of the Bohai Bay Basin. The results indicate that enclosed organic matter in carbonate rocks has not been recognizably altered by post-depositional processes. Two end-member compositions are suggested for early organic matter trapped in the Lower Paleozoic carbonate rocks: (1) a source dominated by aquatic organisms and deposited in a relatively deep marine environment and (2) a relatively high saline, evaporative marine depositional environment. In contrast, chemical and isotopic compositions of solvent extracts from these Lower Paleozoic carbonate rocks are relatively complicated, not only inheriting original characteristics of their precursors, but also overprinted by various post-depositional alterations, such as thermal maturation, biodegradation and mixing. Therefore, the integration of both organic matter characteristics can provide more useful information on the origin of organic matter present in carbonate rocks and the environments of their deposition

Compound-specific C- and H-isotope compositions of enclosed organic matter in carbonate rocks: Implications for source identification of sedimentary organic matter and paleoenvironmental reconstruction

Energy Technology Data Exchange (ETDEWEB)

Xiong Yongqiang [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China)], E-mail: xiongyq@gig.ac.cn; Wang Yanmei; Wang Yongquan; Xu Shiping [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China)

2007-11-15

The Bohai Bay Basin is one of the most important oil-producing provinces in China. Molecular organic geochemical characteristics of Lower Paleozoic source rocks in this area have been investigated by analyzing chemical and isotopic compositions of solvent extracts and acid-released organic matter from the Lower Paleozoic carbonate rocks in the Jiyang Sub-basin of the Bohai Bay Basin. The results indicate that enclosed organic matter in carbonate rocks has not been recognizably altered by post-depositional processes. Two end-member compositions are suggested for early organic matter trapped in the Lower Paleozoic carbonate rocks: (1) a source dominated by aquatic organisms and deposited in a relatively deep marine environment and (2) a relatively high saline, evaporative marine depositional environment. In contrast, chemical and isotopic compositions of solvent extracts from these Lower Paleozoic carbonate rocks are relatively complicated, not only inheriting original characteristics of their precursors, but also overprinted by various post-depositional alterations, such as thermal maturation, biodegradation and mixing. Therefore, the integration of both organic matter characteristics can provide more useful information on the origin of organic matter present in carbonate rocks and the environments of their deposition.

Structural Evolution of Kerogen and Bitumen during Thermal Maturation examined by Fourier-Transform Infrared Spectroscopy

Science.gov (United States)

Craddock, P. R.; Le Doan, T. V.; Pomerantz, A.

2014-12-01

Kerogen—the organic matter that is solid and insoluble in organic solvents—is a key component of organic-rich mudstones. The composition of kerogen affects the storage and transport of hydrocarbons in these unconventional resources and is known to change with thermal maturity. We report here using FTIR spectroscopy, the compositional characteristics of kerogen as a function of thermal maturity, together with the compositional characteristics of the organic phase, bitumen—the organic matter that is solid, but soluble in organic solvents. Kerogen is consumed during thermal maturation, whereas bitumen is an intermediary formed at low maturity from kerogen and consumed at higher maturities in formation of oil and gas. Bitumen relative to kerogen has higher aliphatic content, lower aromatic content, and lower abundance of oxygenated functions. At low maturity (vitrinite reflectance equivalent VRe ~ 0.5-0.9 %), the average length of aliphatic chains in bitumen increases during bitumen formation. At higher thermal maturities (VRe > 1.0-1.3 %), average aliphatic chain length decreases as bitumen is consumed. This evolution contrasts to that in kerogen, where aliphatic chain lengths shorten during all stages of maturation. Breakdown of kerogen appears to be driven by cleavage of oxygen functions at low maturity and removal of aliphatic carbons at higher maturities. These aliphatic-rich fragments may comprise the bitumen, and may in part explain the solubility of bitumen in organic solvents. Bitumen shows evidence of oxidation at low thermal maturity, a phenonemom not documented for kerogen. Bitumen maturation and degradation at higher thermal maturity is driven by cleavage and loss of aliphatic carbons, and is coincident with the maximum generation of oil and gas. The aromatic content of bitumen and of kerogen both increase during maturation as a consequence of the loss of aliphatic carbon. The oil and gas generation potential of the residual organic matter thus

Modification of the process for separating and recovering oil from oil-sands, etc

Energy Technology Data Exchange (ETDEWEB)

Preller, H

1922-08-30

A method of carrying out the process according to Patent 400,122 especially for washing oil or bitumen-bearing mineral materials contaminated with more or less clay, marl, and so forth is characterized in that the oil-bearing raw material is first washed in an opposing stream of warm water for separating the larger part of the oil and settling the larger part of the rock. At the same time the fine clay suspended during the washing operation to a large extent and the remaining rock particles, which are unbound from the oil, by means of a regulatable water stream for further washing are carried into a receptacle of greater cross section, where by the very slow rise of the liquid the finer oil particles find an opportunity to ascend.

Geological evolution, regional perspectives and hydrocarbon potential of the northwest Phu Khanh Basin, offshore Central Vietnam

DEFF Research Database (Denmark)

Fyhn, Michael Bryld Wessel; Nielsen, Lars H.; Boldreel, Lars Ole

2009-01-01

seeps are found at Dam Thi Nai, immediately landward of the basin. Geochemical analyses of the oil seeps indicate the existence of at least two early to peak mature source rocks. Maturation modelling, combined with the seismic analysis, suggests the likely presence of oil kitchens 40-50km downdip...

The chemical and biological evolution of mature fine tailings in oil sands end-pit lakes

International Nuclear Information System (INIS)

Chen, M.; Weisener, C.; Ciborowski, J.

2010-01-01

This presentation described an innovative bench-scale technique to characterize oil sand tailings and their impact on sediment oxygen demand (SOD) for future end-pit lake model behaviour. SOD is a dominant contributor to oxygen depletion in wetlands. The function and sustainability of a wetland ecosystem depends on the biochemical processes occurring at the sediment-water interface. The biochemical reactions associated with natural sediment can change with the addition of oil sands processed material (OSPM), which can affect SOD and ecosystem viability. It is important to establishing the biotic and abiotic controls of SOD. In order to evaluate the effectiveness of current wetland reclamation designs, it is important to establish the biotic and abiotic controls of SOD. The REDOX chemistry of fresh tailings sediment (MFT) was measured in this laboratory microcosm to determine the chemical and biological influences, and to study the role of developing microbial communities as new mature fine tailings (MFT) age. The study evaluated the changes in the main chemical, physical and biological populations of the MFT in both aerobic and anaerobic microcosms. A combination of microelectrode arrays and DNA profiling at the tailings water interface was used in the study.

Source rock potential of the organic rich Turonian - Upper Campanian carbonates of northern Lebanon

Energy Technology Data Exchange (ETDEWEB)

Daher, S. Bou; Littke, R. [RWTH Aachen Univ. (Germany). Energy and Mineral Resources Group (EMR); Nader, F.H. [IFP Energies nouvelles, Paris (France). Dept. of Sedimentology-Stratigraphy

2013-08-01

Upper Cretaceous chalks, marls, and shales are arguably the most prolific petroleum source rocks in the eastern Mediterranean region. 209 core samples from the Turonian - Upper Campanian rock succession in north Lebanon were collected and analyzed for their organic matter (OM) content, quality, and maturity. The total organic carbon (TOC) measurements revealed a very good source rock potential for a 150 m interval within the Upper Santonian - Upper Campanian, with an average of 2% TOC. High HI values (average 707 mg/g TOC) characterize these source rocks as type I kerogen and reflect a very good preservation of the organic matter. T{sub max} values (average 421 C) match the other maturity parameters such as vitrinite reflectance (average 0.35%), and all point towards immature organic matter. The equivalent Upper Cretaceous in the offshore Levant basin has enough overburden to have reached maturity. However, the accurate extrapolation of the organic matter quality and quantity to the offshore is yet a challenge with the data at hand. (orig.)

Epigenetic alterations of sedimentary rocks at deposits

International Nuclear Information System (INIS)

Komarova, G.V.; Kondrat'eva, I.A.; Zelenova, O.I.

1980-01-01

Notions are explained, and technique for studying epigenetic alterations of sedimentary rocks at uranium deposits is described. Main types of epigenetic transformations and their mineralogic-geochemical characteristics are considered. Rock alterations, accompanying uranium mineralization, can be related to 2 types: oxidation and reduction. The main mineralogic-geochemical property of oxidation transformations is epigenetic limonitization. Stratal limonitization in primary grey-coloured terrigenic rocks and in epigenetically reduced (pyritized) rocks, as well as in rock, subjected to epigenetic gleying, are characterized. Reduction type of epigenetic transformations is subdivided into sulphidic and non-sulphidic (gley) subtypes. Sulphidic transformations in grey-coloured terrigenic rocks with organic substance of carbonic row, in rocks, containing organic substance of oil row, sulphide transformations of sedimentary rocks, as well as gley transformations, are considered

Oil formation in the process of lithogenesis in the light of the systems approach

Energy Technology Data Exchange (ETDEWEB)

Lopatin, N.V.

1977-03-01

It is suggested that systems analysis techniques be used to reproduce the actual historical process of oil formation as a part of the overall system of a sedimentary rock basin, in order to determine the conditions of transition of one stage of development of the object to another, determine interrelationships between elements of the system and peculiarities of its functioning, provide a detailed description of the mature stage of the process, the primary phase of oil formation, by partial solution of the problem and formulate the new problem of recognition of oil formation, closely related to the search for deposits of oil. The systems approach is a modern methodological orientation which, though it does not guarantee the production of true knowledge, since a great deal is determined by the reliability of the empirical basis of data, skill of the researcher and even such materialistic factors as intuition and creative imagination, does provide the possibility for creation of a single theoretical picture and development of mathematically founded concepts in this area of research.

Solid as a rock

International Nuclear Information System (INIS)

Pincus, H.J.

1984-01-01

Recent technologic developments have required a more comprehensive approach to the behavior of rock mass or rock substance plus discontinuities than was adequate previously. This work considers the inherent problems in such operations as the storage of hot or cold fluids in caverns and aquifers, underground storage of nuclear waste, underground recovery of heat from hydrocarbon fuels, tertiary recovery of oil by thermal methods, rapid excavation of large openings at shallow to great depths and in hostile environments, and retrofitting of large structures built on or in rock. The standardization of methods for determining rock properties is essential to all of the activities described, for use not only in design and construction but also in site selection and post-construction monitoring. Development of such standards is seen as a multidisciplinary effort

Iron speciation and mineral characterization of upper Jurassic reservoir rocks in the Minhe Basin, NW China

Energy Technology Data Exchange (ETDEWEB)

Ma, Xiangxian; Zheng, Guodong, E-mail: gdzhbj@mail.iggcas.ac.cn; Xu, Wang [Chinese Academy of Sciences, Key Laboratory of Petroleum Resources, Gansu Province / Key Laboratory of Petroleum Resources Research, Institute of Geology and Geophysics (China); Liang, Minliang [Chinese Academy of Geological Sciences, Institute of Geomechanics, Key Lab of Shale Oil and Gas Geological Survey (China); Fan, Qiaohui; Wu, Yingzhong; Ye, Conglin [Chinese Academy of Sciences, Key Laboratory of Petroleum Resources, Gansu Province / Key Laboratory of Petroleum Resources Research, Institute of Geology and Geophysics (China); Shozugawa, Katsumi; Matsuo, Motoyuki [The University of Tokyo, Graduate School of Arts and Sciences (Japan)

2016-12-15

Six samples from a natural outcrop of reservoir rocks with oil seepage and two control samples from surrounding area in the Minhe Basin, northwestern China were selectively collected and analyzed for mineralogical composition as well as iron speciation using X-ray powder diffraction (XRD) and Mössbauer spectroscopy, respectively. Iron species revealed that: (1) the oil-bearing reservoir rocks were changed by water-rock-oil interactions; (2) even in the same site, there was a different performance between sandstone and mudstone during the oil and gas infusion to the reservoirs; and (3) this was evidence indicating the selective channels of hydrocarbon migration. In addition, these studies showed that the iron speciation by Mössbauer spectroscopy could be useful for the study of oil and gas reservoirs, especially the processes of the water-rock interactions within petroleum reservoirs.

Alteration of properties of rock during their selection by shooting core lifter

Energy Technology Data Exchange (ETDEWEB)

Malinin, V F

1969-01-01

During the process of intrusion of the core lifter into rock, splitting and dislocation of the granules and crystals which compose it occur. In the core lifters, single small nondisintegrated fragments are sometimes encountered. Data on comparison of porosity of crushed cores and rock from which they were selected indicate increase in porosity and penetration of the filtrate of the drilling solution during the process of coring. The determined residual oil saturation of the core is different from the residual oil saturation of the rock from which they were selected. The permeability of cores of rock with high porosity is altered.

Enriching acid rock drainage related microbial communities from surface-deposited oil sands tailings.

Science.gov (United States)

Dean, Courtney; Xiao, Yeyuan; Roberts, Deborah J

2016-10-01

Little is known about the microbial communities native to surface-deposited pyritic oil sands tailings, an environment where acid rock drainage (ARD) could occur. The goal of this study was to enrich sulfur-oxidizing organisms from these tailings and determine whether different populations exist at pH levels 7, 4.5, and 2.5. Using growth-based methods provides model organisms for use in the future to predict potential activities and limitations of these organisms and to develop possible control methods. Thiosulfate-fed enrichment cultures were monitored for approximately 1 year. The results showed that the enrichments at pH 4.5 and 7 were established quicker than at pH 2.5. Different microbial community structures were found among the 3 pH environments. The sulfur-oxidizing microorganisms identified were most closely related to Halothiobacillus neapolitanus, Achromobacter spp., and Curtobacterium spp. While microorganisms related to Chitinophagaceae and Acidocella spp. were identified as the only possible iron-oxidizing and -reducing microbes. These results contribute to the general knowledge of the relatively understudied microbial communities that exist in pyritic oil sands tailings and indicate these communities may have a potential role in ARD generation, which may have implications for future tailings management.

Investigated Miscible CO2 Flooding for Enhancing Oil Recovery in Wettability Altered Chalk and Sandstone Rocks

Energy Technology Data Exchange (ETDEWEB)

Tabrizy, Vahid Alipour

2012-07-01

The thesis addresses oil recovery by miscible CO2 flooding from modified sandstone and chalk rocks. Calcite mineral surface is modified with stearic acid (SA) and asphaltene, and the silicate mineral surfaces are modified with N,N-dimethyldodecylamine (NN-DMDA) and asphaltene. The stability of adsorbed polar components in presence of SO4 2- and Mg2 + ions is also investigated. Recovery from sandstone cores is consistently lower than that from chalk cores saturated with the same oil and flooded with CO2 at all miscible flooding conditions. This may be due to the larger permeability contrasts in sandstone cores, which promote the fingering phenomenon. Miscible CO2 flooding for chalk and sandstone cores with distilled water, as initial water saturation, shows also lower oil recovery than cores saturated with different ions. At higher miscible flooding conditions, higher oil recovery is obtained. However, presence of light components (such as C1 or C3) in oil reduced the recovery. Oil recovery in presence of methane (C1) is lower than that in presence of methane and propane (C1/C3). A ternary diagram was constructed in order to understand the CO2 flooding mechanism(s) at the different flooding conditions and in presence of light components. The side effect of the flooding with CO2 is the probability for asphaltene deposition. An approach based on solubility parameter in the liquid, is used to assess the risk for asphaltene deposition during CO2 miscible flooding. The light components (C1/C3) and higher flooding conditions enhanced the risk for asphaltene instability. It is also shown higher amount of asphaltene deposition in chalk cores than that in sandstone cores at similar miscibility conditions.(au)

Sustaining Petroleum Exploration and Development in Mature Basins: Production Sharing Contracts and Financing of Joint Venture Oil and Gas Projects

International Nuclear Information System (INIS)

Chukwueke, T.

2002-01-01

Oil companies make a business by bearing the risks of investing in, and making profits from, oil and gas operations. International Oil Companies (IOC) are the recognised leaders in technology and develop expertise in the management of technical such as subsurface and surface uncertainties through seismic surveys, well drilling and production facilities. In export oriented oil and gas developments, IOCs also carry the commercial risks associated with the export market (ups and downs in the demand for oil and gas) that could make the project non-profitable, if not properly managed.Conversely, Local Oil Companies (LOCs), i.e. indigenous private or state owned companies, are more adapt at developing expertise in the management of the local environmental, domestic market and political risks associated with the area or country of operations. It is recognised that in certain countries some LOCs are also making significant progress in the acquisition of modern technology. Any critical business risks which cannot be adequately managed by either the IOC or the LOC will require the involvement of third party, who will normally provide guarantee or securitisation in one form or another.A partnership between local and international oil companies has become accepted to be the most secure and profitable arrangement in international oil and gas business. In the Niger Delta, which is mature oil and gas province and as such non-market related risks, particularly technical and supply risks, are substantially reduced, Joint Venture type of arrangement is considered the most suitable form of partnership. Joint Venture arrangement allows each partner to fund the venture in direct proportion to its participation interest. Because of the reduced risks profile, the joint venture is more bankable; each partner can therefore secure funding for its share with its revenue profile. In Nigeria, however, where the revenue profile (and consequently development budget) of the dominant local player

Variations in fatty acid composition during maturation of cumin ...

African Journals Online (AJOL)

Changes in fatty acids were studied during maturation of cumin (Cuminum cyminum L.) seeds cultivated in the North-Eastern region of Tunisia (Menzel Temim). The fruits matured in 49 Days after flowering (DAF). The first results show a rapid oil accumulation started in newly formed fruits (8.2%) and continued until their full ...

Compact rock material gas permeability properties

Energy Technology Data Exchange (ETDEWEB)

Wang, Huanling, E-mail: whl_hm@163.com [Key Laboratory of Coastal Disaster and Defence, Ministry of Education, Hohai University, Nanjing 210098 (China); LML, University of Lille, Cite Scientifique, 59655 Villeneuve d’Ascq (France); Xu, Weiya; Zuo, Jing [Institutes of Geotechnical Engineering, Hohai University, Nanjing 210098 (China)

2014-09-15

Natural compact rocks, such as sandstone, granite, and rock salt, are the main materials and geological environment for storing underground oil, gas, CO{sub 2,} shale gas, and radioactive waste because they have extremely low permeabilities and high mechanical strengths. Using the inert gas argon as the fluid medium, the stress-dependent permeability and porosity of monzonitic granite and granite gneiss from an underground oil storage depot were measured using a permeability and porosity measurement system. Based on the test results, models for describing the relationships among the permeability, porosity, and confining pressure of rock specimens were analyzed and are discussed. A power law is suggested to describe the relationship between the stress-dependent porosity and permeability; for the monzonitic granite and granite gneiss (for monzonitic granite (A-2), the initial porosity is approximately 4.05%, and the permeability is approximately 10{sup −19} m{sup 2}; for the granite gneiss (B-2), the initial porosity is approximately 7.09%, the permeability is approximately 10{sup −17} m{sup 2}; and the porosity-sensitivity exponents that link porosity and permeability are 0.98 and 3.11, respectively). Compared with moderate-porosity and high-porosity rocks, for which φ > 15%, low-porosity rock permeability has a relatively lower sensitivity to stress, but the porosity is more sensitive to stress, and different types of rocks show similar trends. From the test results, it can be inferred that the test rock specimens’ permeability evolution is related to the relative particle movements and microcrack closure.

Geochemical evaluation of the middle Magdalena basing Colombia

International Nuclear Information System (INIS)

Ramon, J.C; Dzou, L; Giraldo, B

1997-01-01

The chemical composition of 25 crude oils from Tertiary reservoirs and 12 rock extracts from five organic-rich Cretaceous formations in the middle Magdalena Basin, Colombia were studied in detail by geochemical methods in order to understand their genetic relationships. The oils have been geochemically classified into four main groups based on the sulfur content, pristane/phytane, dibenzothiophene /phenanthrene, concentrations of oleanane and terpane distributions. Each group occurs in different geographic locations. Oils were mainly derived from calcareous, siliciclastic and mixture of these two facies of the Upper Cretaceous La Luna Formation. Source-oil correlation is supported by sterane and terpane distributions of and carbon isotope ratios. Some oils in the eastern margin contain relatively higher concentrations of higher plant indicators than the remaining oil samples. The molecular compositions of the oils observed in this study appear to be consistent with the inferred depositional sequence of anoxic marine/pelagic carbonate facies in the north/western sector of the Middle Magdalena, while the eastern sector received a higher proportion of clastic input. This documentation supports the interpretation that the Middle Magdalena oils have been generated 'locally', as opposed to have migrated from the region of the Eastern Cordillera. Biomarker maturity parameters indicate that the majority of oils were generated in the early thermal maturity oil window except the Colorado-38 oil, which was generated in the middle thermal maturity oil window. Oil maturity data also supports the short migration distances of oils from the early-mature source rocks to the reservoir rocks. The composition of some oils (e.g., La Cira, Infantas, Conde and Bonanza) is unusual in that gas chromatographic data contains an n-alkane and isoprenoid distribution normally associated with moderately degraded oils, but they also contain a relatively high abundance of gasoline hydrocarbons

Novel approaches to microbial enhancement of oil recovery.

Science.gov (United States)

Kryachko, Yuriy

2018-01-20

Microbially enhanced oil recovery (MEOR) was shown to be feasible in a number of laboratory experiments and field trials. However, it has not been widely used in the oil industry because necessary conditions cannot always be easily established in an oil reservoir. Novel approaches to MEOR, which are based on newly discovered biosurfactant-mediated MEOR-mechanisms, are discussed in this review. Particularly, the possibility of combining MEOR with chemical enhancement of oil recovery in heterogeneous oil reservoirs, which involves rock surface wettability shifts and emulsion inversions, is discussed. In wider (centimeter/millimeter-scale) rock pores, the activity of (bio)surfactants and microbial cells attached to oil may allow releasing trapped oil blobs through oil-in-water emulsification. After no more oil can be emulsified, the addition of alkali or surfactants, which turn rock surface oil-wet, may help release oil droplets trapped in narrow (micrometer-scale) pores through coalescence of the droplets and water-in-oil emulsification. Experiments demonstrating the possibility of (bio)surfactant-mediated enhancement of immiscible gas-driven oil recovery are also reviewed. Interestingly, very low (bio)surfactant concentrations were shown to be needed for enhancement of immiscible gas-driven oil recovery. Some possible side effects of MEOR, such as unintended bioplugging and microbially influenced corrosion (MIC), are discussed as well. Crown Copyright © 2017. Published by Elsevier B.V. All rights reserved.

Geochemistry and habitat of oils in Italy

Energy Technology Data Exchange (ETDEWEB)

Novelli, L.; Mattavelli, L.

1988-01-01

Most of the onshore and offshore oil occurrences found in Italy have been systematically analyzed by different techniques, i.e., capillary gas chromatography, biological markers, and stable isotopes composition. On the basis of the above analyses, ten different groups of oil have been identified and geographically located. Subsequently, the influence of the various geological settings on generation and migration of these different groups of oils was investigated and is discussed here. Due to its complex geological and tectonic history, the Alpine-Apennine chain behaved differently with regard to oil generation and migration in different areas. In fact, the high temperatures reached by the Mesozoic source rocks underneath a stack of allochthonous thrust sheets and the insulting thermal blanket effect exerted by the same sheets on other younger source rocks above gave rise to generally light oils. Furthermore, in this unique geological setting, the most external thrust sheets locally acted as reservoirs of the foredeep regime. Foreland sequences acted as both reservoirs of the foredeep oils and as generative kitchens of liquid hydrocarbons if suitable source rocks were present and adequate burial was reached.

Self-Healing Characteristics of Damaged Rock Salt under Different Healing Conditions

Directory of Open Access Journals (Sweden)

Lin Li

2013-08-01

Full Text Available Salt deposits are commonly regarded as ideal hosts for geologic energy reservoirs. Underground cavern construction-induced damage in salt is reduced by self-healing. Thus, studying the influencing factors on such healing processes is important. This research uses ultrasonic technology to monitor the longitudinal wave velocity variations of stress-damaged rock salts during self-recovery experiments under different recovery conditions. The influences of stress-induced initial damage, temperature, humidity, and oil on the self-recovery of damaged rock salts are analyzed. The wave velocity values of the damaged rock salts increase rapidly during the first 200 h of recovery, and the values gradually increase toward stabilization after 600 h. The recovery of damaged rock salts is subjected to higher initial damage stress. Water is important in damage recovery. The increase in temperature improves damage recovery when water is abundant, but hinders recovery when water evaporates. The presence of residual hydraulic oil blocks the inter-granular role of water and restrains the recovery under triaxial compression. The results indicate that rock salt damage recovery is related to the damage degree, pore pressure, temperature, humidity, and presence of oil due to the sealing integrity of the jacket material.

Geochemistry and habitat of oils in Italy

Energy Technology Data Exchange (ETDEWEB)

Novelli, L.; Mattavelli, L.

1988-02-01

Most of the onshore and offshore oil occurrences found in Italy have been systematically analyzed by different techniques, i.e., capillary gas chromatography, biological markers, and stable isotopes composition. On the basis of the above analyses, ten different groups of oil have been identified and geographically located. Subsequently, the influence of the various geological settings on generation and migration of these different groups of oils was investigated and is discussed here. In a foredeep regime, the remarkably fast heating rates, due to the rapid burial during late Tertiary, caused a rapid generation of oil mainly in the Triassic carbonate source rocks. Such generation, combined with the high over-burden pressure and a contemporaneous development of an intense tectonic compression, resulted in the expulsion of immature, heavy oils. Examples of this are evident in the central Adriatic Sea, southern Italy, and southeastern Sicily. Due to its complex geological and tectonic history, the Alpine-Apennine chain behaved differently with regard to oil generation and migration in different areas. In fact, the high temperatures reached by the Mesozoic source rocks underneath a stack of allochthonous thrust sheets and the insulating thermal blanket effect exerted by the same sheets on other younger source rocks above gave rise to generally light oils. Furthermore, in this unique geological setting, the most external thrust sheets locally acted as reservoirs of the foredeep regime. Foreland sequences acted as both reservoirs of the foredeep oils and as generative kitchens of liquid hydrocarbons if suitable source rocks were present and adequate burial was reached.

Significance of Isotopically Labile Organic Hydrogen in Thermal Maturation of Organic Matter

Energy Technology Data Exchange (ETDEWEB)

Arndt Schimmelmann; Maria Mastalerz

2010-03-30

Isotopically labile organic hydrogen in fossil fuels occupies chemical positions that participate in isotopic exchange and in chemical reactions during thermal maturation from kerogen to bitumen, oil and gas. Carbon-bound organic hydrogen is isotopically far less exchangeable than hydrogen bound to nitrogen, oxygen, or sulfur. We explore why organic hydrogen isotope ratios express a relationship with organic nitrogen isotope ratios in kerogen at low to moderate maturity. We develop and apply new techniques to utilize organic D/H ratios in organic matter fractions and on a molecular level as tools for exploration for fossil fuels and for paleoenvironmental research. The scope of our samples includes naturally and artificially matured substrates, such as coal, shale, oil and gas.

LOX Gene Transcript Accumulation in Olive (Olea europaea L. Fruits at Different Stages of Maturation: Relationship between Volatile Compounds, Environmental Factors, and Technological Treatments for Oil Extraction

Directory of Open Access Journals (Sweden)

Innocenzo Muzzalupo

2012-01-01

Full Text Available The quality of olive oil is influenced by genetic and environmental factors and by the maturation state of drupes, but it is equally affected by technological treatments of the process. This work investigates the possible correlation between olive LOX gene transcript accumulation, evaluated in fruits collected at different stages of maturation, and chemical biomarkers of its activity. During olive fruit ripening, the same genotype harvested from two different farms shows a positive linear trend between LOX relative transcript accumulation and the content of volatile compounds present in the olive oil aroma. Interestingly, a negative linear trend was observed between LOX relative transcript accumulation and the content of volatile compounds present in the olive pastes obtained from olive fruits with and without malaxation. The changes in the olive LOX transcript accumulation reveal its environmental regulation and suggest differential physiological functions for the LOXs.

Effect of Thermal Maturation on n-alkanes and Kerogen in Preserved Organic Matter: Implications for Paleoenvironment Biomarkers

Science.gov (United States)

Craven, O. D.; Longbottom, T. L.; Hockaday, W. C.; Blackaby, E.

2017-12-01

Understanding the effects of maturity on biomarkers is vital in assessing biomarker reliability in mature sediments. It is well known for n-alkanes that increased maturity shortens chain lengths and decreases the odd over even preference however, the amount of change in these variables has not been determined for different maturities and types of preserved organic matter. For this reason, it is difficult to judge the trustworthiness of even lightly matured samples for paleoenvironment reconstruction. Another complication is the difficulty of accurately determining maturity as many maturity indicators are error-prone or not appropriate at low maturities. Using hydrous pyrolysis, we artificially matured black shale samples with type I (lacustrine) and type II (marine) kerogen to measure changes in n-alkane length and odd over even preference. Whole rock samples underwent hydrous pyrolysis for 72 hours, at 250 °C, 300 °C, 325 °C, 350 °C, and 375 °C to cover a wide maturity range. From the immature and artificially matured samples, the bitumen was extracted and the saturate fraction was separated using column chromatography. The saturate fraction was analyzed for n-alkanes using gas chromatography-mass spectroscopy. Kerogen structural changes were also measured using solid-state 13C NMR to relate changes in n-alkane biomarkers to changes in kerogen structure. Results show that for type I bitumen the n-alkanes did not change at low maturities considered premature in terms of oil generation (<325 °C). The NMR spectra of the type I kerogen support the lack of change, at low maturities no changes in the aliphatic portion (Fal) were observed, however, after 325 °C Fal decreased with increasing maturity. The loss of Fal indicates kerogen contributing hydrocarbons to bitumen that cause changes in n-alkane measurements. The type II kerogen's Fal also decreased with increasing maturity, but unlike the type I kerogen Fal loss started at low maturities. The differences

Compositional changes of aromatic steroid hydrocarbons in naturally weathered oil residues in the Egyptian western desert

International Nuclear Information System (INIS)

Barakat, A.O.; Qian, Y.; Kim, M.; Kennicutt, M.C. II

2002-01-01

Aromatic steranes are geochemical markers that can be used to study the maturation of organic matter of sediments and to correlate crude oils and source rocks. In this study, naturally weathered oil residues from an arid waste disposal site in Al-Alamein, Egypt, were analyzed for monoaromatic and triaromatic steranes to show the usefulness of biomarker compounds in assessing changes in chemical composition during the degradation of oil residues that have been released onto terrestrial environments. Gas chromatography and mass spectrometry were used to characterize the individual aromatic compounds. Results indicate that triaromatic sterane distributions are similar in oil residues with varying extents of weathering. The distribution correlated with a fresh crude oil sample from Western Desert-sourced oil. Molecular ratios of triaromatic sterane compounds were found to be suitable for source identification. The major changes in chemical compositions resulting from the weathering of the oil included the depletion of short chain mono- and tri-aromatic steranes in extremely weathered samples. The results of the triaromatic sterane distribution correspond with weathering classifications based on the analyses of saturated and aromatic hydrocarbons and the ratios of n-alkanes, polycyclic aromatic hydrocarbons, and saturate biomarker compounds. 15 refs., 3 tabs., 3 figs

NMR studies of the molecules dynamics to the solid-liquid interfaces: from graded porous materials to oil rocks; Etudes RMN de la dynamique des molecules aux interfaces solide-liquide: des materiaux poreux calibres aux roches petroliferes

Energy Technology Data Exchange (ETDEWEB)

Godefroy, S

2001-11-01

Low field NMR relaxation for laboratory or in-situ applications provides critical information for oil recovery such as porosity, saturation, and permeability of rocks. In addition, pore size distribution and wettability can also be obtained in some cases. The technique relies on the measurement of proton longitudinal (T{sub 1}) or transverse (T{sub 2}) nuclear relaxation times. For better predictions, the surface micro-dynamics and the chemical properties of the liquids entrapped in the pore space are important and must be characterized. It is well known that the NMR relaxation is enhanced by the paramagnetic impurities at the pore surface but many other parameters influence the relaxation time distributions. These parameters are used to derive the petrophysical properties of the rocks. We propose here an original method to probe the dynamics of water and oil at the pore surface. In the present study, we used both nuclear relaxation at 2.2 MHz and field cycling Nuclear Magnetic Relaxation Dispersion (NMRD) techniques. We applied these two techniques to different kinds of water or oil saturated macroporous media (grain packings, outcrop and reservoir rocks with SiO{sub 2} or CaCO{sub 3} surfaces). We studied the dependence of NMR relaxation on pore size, magnetic field and temperature. Varying the pore size and the surface density of paramagnetic impurities of water saturated grain packings allowed experimental evidence for the two limiting regimes of the water relaxation in pores (surface- and diffusion-limited regimes). NMRD technique (evolution of 1/T{sub 1} with the magnetic field) allowed us to probe liquid surface dynamics in water or oil fully saturated grain packing, outcrop rocks or reservoir rocks (water- and oil-wet surfaces). We evidenced a two-dimensional molecular surface diffusion and directly estimated important parameters such as correlation times, residence times and molecular self-diffusion on the surface. Finally, we proved that the temperature

Rock Physics of Reservoir Rocks with Varying Pore Water Saturation and Pore Water Salinity

DEFF Research Database (Denmark)

Katika, Konstantina

experiments, the rock is subjected to high external stresses that resemble the reservoir stresses; 2) the fluid distribution within the pore space changes during the flow through experiments and wettability alterations may occur; 3) different ions, present in the salt water injected in the core, interact......Advanced waterflooding (injection of water with selective ions in reservoirs) is a method of enhanced oil recovery (EOR) that has attracted the interest of oil and gas companies that exploit the Danish oil and gas reservoirs. This method has been applied successfully in oil reservoirs...... and in the Smart Water project performed in a laboratory scale in order to evaluate the EOR processes in selected core plugs. A major step towards this evaluation is to identify the composition of the injected water that leads to increased oil recovery in reservoirs and to define changes in the petrophysical...

Compositional modification of crude oil during oil recovery

Energy Technology Data Exchange (ETDEWEB)

Zhu, Yangming; Weng, Huanxin [Department of Earth Sciences, Zhejiang University, Hangzhou 310027 (China); Chen, Zulin; Chen, Qi [Petroleum Geochemistry Research Center, Jianghan Petroleum University, Jingzhou, Hubei (China)

2003-05-01

Ten crude oils from two recovery stages spanning 5-10-year interval of five productive wells in the Tarim Basin, northwest China were analyzed for their compositional modification during production process. Significant compositional changes in polar and nonpolar fractions between the previous oil samples and the latter ones were noted at both bulk and molecular level. The latter oil samples appear to contain more aromatic fraction and less asphaltenes and resin, and their gas chromatography (GC) data for whole oil show reduced alkanes with low molecular weight and enhanced high homologue relative to the previous oil samples. Compared with the oils collected from the previous recovery stage, the concentration of basic type of nitrogen-containing compounds and organic acids in oils from the latter recovery stage have a reducing trend, suggesting the occurrence of interaction between crude oil and reservoir rock.

Fluid-Rock Characterization and Interactions in NMR Well Logging

Energy Technology Data Exchange (ETDEWEB)

Hirasaki, George J.; Mohanty, Kishore K.

2003-02-10

The objective of this project was to characterize the fluid properties and fluid-rock interactions which are needed for formation evaluation by NMR well logging. NMR well logging is finding wide use in formation evaluation. The formation parameters commonly estimated were porosity, permeability, and capillary bound water. Special cases include estimation of oil viscosity, residual oil saturation, location of oil/water contact, and interpretation on whether the hydrocarbon is oil or gas.

AL-PAM assisted filtration of mature fine tailings produced from oil sands development

Energy Technology Data Exchange (ETDEWEB)

Alamgir, A.; Masliyah, J.; Xu, Z. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemical and Materials Engineering

2010-07-01

The inventory of mature fine tailings (MFT) produced by the oil sands extraction process continues to grow, and is considered as a long-term environmental liability. Large amounts of water are trapped in the MFT, and the tailings ponds present a threat to local wildlife and ecosystems. This PowerPoint presentation discussed a research project that is being conducted to identify conditions for producing stackable MFT deposits. The study is investigating various types and dosages of polymers and evaluating the degrees of MFT dilution and process configurations needed to maximize re-usable water recovery. Polymeric flocculants include AL-PAM and Magnafloc 1011. Settling tests have demonstrated that 50 ppm is the optimum dosage for both polymers when MFT is diluted to 5 wt percent solids, while 75 ppm of AL-PAM and 100 ppm of MF1011 are optimum dosages for MFT diluted to 10 wt percent solids. A novel supernatant filtration method was then used to produce filtration cakes and water. The study showed that the supernatant can be used to further dilute the MFTs. tabs., figs.

Oil shale commercialization study

Energy Technology Data Exchange (ETDEWEB)

Warner, M.M.

1981-09-01

Ninety four possible oil shale sections in southern Idaho were located and chemically analyzed. Sixty-two of these shales show good promise of possible oil and probable gas potential. Sixty of the potential oil and gas shales represent the Succor Creek Formation of Miocene age in southwestern Idaho. Two of the shales represent Cretaceous formations in eastern Idaho, which should be further investigated to determine their realistic value and areal extent. Samples of the older Mesozonic and paleozoic sections show promise but have not been chemically analyzed and will need greater attention to determine their potential. Geothermal resources are of high potential in Idaho and are important to oil shale prospects. Geothermal conditions raise the geothermal gradient and act as maturing agents to oil shale. They also might be used in the retorting and refining processes. Oil shales at the surface, which appear to have good oil or gas potential should have much higher potential at depth where the geothermal gradient is high. Samples from deep petroleum exploration wells indicate that the succor Creek shales have undergone considerable maturation with depth of burial and should produce gas and possibly oil. Most of Idaho's shales that have been analyzed have a greater potential for gas than for oil but some oil potential is indicated. The Miocene shales of the Succor Creek Formation should be considered as gas and possibly oil source material for the future when technology has been perfectes. 11 refs.

Real-time detection of dielectric anisotropy or isotropy in unconventional oil-gas reservoir rocks supported by the oblique-incidence reflectivity difference technique.

Science.gov (United States)

Zhan, Honglei; Wang, Jin; Zhao, Kun; Lű, Huibin; Jin, Kuijuan; He, Liping; Yang, Guozhen; Xiao, Lizhi

2016-12-15

Current geological extraction theory and techniques are very limited to adequately characterize the unconventional oil-gas reservoirs because of the considerable complexity of the geological structures. Optical measurement has the advantages of non-interference with the earth magnetic fields, and is often useful in detecting various physical properties. One key parameter that can be detected using optical methods is the dielectric permittivity, which reflects the mineral and organic properties. Here we reported an oblique-incidence reflectivity difference (OIRD) technique that is sensitive to the dielectric and surface properties and can be applied to characterization of reservoir rocks, such as shale and sandstone core samples extracted from subsurface. The layered distribution of the dielectric properties in shales and the uniform distribution in sandstones are clearly identified using the OIRD signals. In shales, the micro-cracks and particle orientation result in directional changes of the dielectric and surface properties, and thus, the isotropy and anisotropy of the rock can be characterized by OIRD. As the dielectric and surface properties are closely related to the hydrocarbon-bearing features in oil-gas reservoirs, we believe that the precise measurement carried with OIRD can help in improving the recovery efficiency in well-drilling process.

Experimental Study on Water Sensitivity Difference Based on Oiliness of Porous Medium Rock

Directory of Open Access Journals (Sweden)

Jie Li

2017-01-01

Full Text Available This study presents the differences of water sensitivity experiment of porous medium rock between conventional dry core samples and oil-bearing core. The comparison was made to analyze the impact of single-phase fluid and multiphase fluid on the actual sensitivity of rock. The nuclear magnetic resonance (NMR test was carried out to reveal the distribution of oil in porous medium and the microscopic influence mechanism of oil phase. The study shows that the initial oil in place could isolate the clay from water, and then the expansion and the migration of the clay were prevented to reduce the decrease of degree of damage.

Bacterial community diversity in a low-permeability oil reservoir and its potential for enhancing oil recovery.

Science.gov (United States)

Xiao, Meng; Zhang, Zhong-Zhi; Wang, Jing-Xiu; Zhang, Guang-Qing; Luo, Yi-Jing; Song, Zhao-Zheng; Zhang, Ji-Yuan

2013-11-01

The diversity of indigenous bacterial community and the functional species in the water samples from three production wells of a low permeability oil reservoir was investigated by high-throughput sequencing technology. The potential of application of indigenous bacteria for enhancing oil recovery was evaluated by examination of the effect of bacterial stimulation on the formation water-oil-rock surface interactions and micromodel test. The results showed that production well 88-122 had the most diverse bacterial community and functional species. The broth of indigenous bacteria stimulated by an organic nutrient activator at aerobic condition changed the wettability of the rock surface from oil-wet to water-wet. Micromodel test results showed that flooding using stimulated indigenous bacteria following water flooding improved oil recovery by 6.9% and 7.7% in fractured and unfractured micromodels, respectively. Therefore, the zone of low permeability reservoir has a great potential for indigenous microbial enhanced oil recovery. Copyright © 2013 Elsevier Ltd. All rights reserved.

Digital Rock Simulation of Flow in Carbonate Samples

Science.gov (United States)

Klemin, D.; Andersen, M.

2014-12-01

Reservoir engineering has becomes more complex to deal with current challenges, so core analysts must understand and model pore geometries and fluid behaviors at pores scales more rapidly and realistically. We introduce an industry-unique direct hydrodynamic pore flow simulator that operates on pore geometries from digital rock models obtained using microCT or 3D scanning electron microscope (SEM) images. The PVT and rheological models used in the simulator represent real reservoir fluids. Fluid-solid interactions are introduced using distributed micro-scale wetting properties. The simulator uses density functional approach applied for hydrodynamics of complex systems. This talk covers selected applications of the simulator. We performed microCT scanning of six different carbonate rock samples from homogeneous limestones to vuggy carbonates. From these, we constructed digital rock models representing pore geometries for the simulator. We simulated nonreactive tracer flow in all six digital models using a digital fluid description that included a passive tracer solution. During the simulation, we evaluated the composition of the effluent. Results of tracer flow simulations corresponded well with experimental data of nonreactive tracer floods for the same carbonate rock types. This simulation data of the non-reactive tracer flow can be used to calculate the volume of the rock accessible by the fluid, which can be further used to predict response of a porous medium to a reactive fluid. The described digital core analysis workflow provides a basis for a wide variety of activities, including input to design acidizing jobs and evaluating treatment efficiency and EOR economics. Digital rock multiphase flow simulations of a scanned carbonate rock evaluated the effect of wettability on flow properties. Various wetting properties were tested: slightly oil wet, slightly water wet, and water wet. Steady-state relative permeability simulations yielded curves for all three

Experimental investigation of changes in methane adsorption of bitumen-free Woodford Shale with thermal maturation induced by hydrous pyrolysis

Science.gov (United States)

Hu, Haiyan; Zhang, Tongwei; Wiggins-Camacho, Jaclyn D.; Ellis, Geoffrey S.; Lewan, Michael D.; Zhang, Xiayong

2014-01-01

This study quantifies the effects of organic-matter (OM) thermal maturity on methane (CH4) sorption, on the basis of five samples that were artificially matured through hydrous pyrolysis achieved by heating samples of immature Woodford Shale under five different time–temperature conditions. CH4-sorption isotherms at 35 °C, 50 °C, and 65 °C, and pressures up to 14 MPa on dry, solvent-extracted samples of the artificially matured Woodford Shale were measured. The results showed that CH4-sorption capacity, normalized to TOC, varied with thermal maturity, following the trend: maximum oil (367 °C) > oil cracking (400 °C) > maximum bitumen/early oil (333 °C) > early bitumen (300 °C) > immature stage (130 °C). The Langmuir constants for the samples at maximum-oil and oil-cracking stages are larger than the values for the bitumen-forming stages. The total pore volume, determined by N2 physisorption at 77 K, increases with increased maturation: mesopores, 2–50 nm in width, were created during the thermal conversion of organic-matter and a dramatic increase in porosity appeared when maximum-bitumen and maximum-oil generation stages were reached. A linear relationship between thermal maturity and Brunauer–Emmett–Teller (BET) surface area suggests that the observed increase in CH4-sorption capacity may be the result of mesopores produced during OM conversion. No obvious difference is observed in pore-size distribution and pore volume for samples with pores 2 physisorption at 273 K. The isosteric heat of adsorption and the standard entropy for artificially matured samples ranged from 17.9 kJ mol−1 to 21.9 kJ mol−1 and from −85.4 J mol−1 K−1 to −101.8 J mol−1 K−1, respectively. These values are similar to the values of immature Woodford kerogen concentrate previously observed, but are larger than naturally matured organic-rich shales. High-temperature hydrous pyrolysis might have induced Lewis acid sites on both organic and mineral surfaces

Trace metal mobilization from oil sands froth treatment thickened tailings exhibiting acid rock drainage.

Science.gov (United States)

Kuznetsova, Alsu; Kuznetsov, Petr; Foght, Julia M; Siddique, Tariq

2016-11-15

Froth treatment thickened tailings (TT) are a waste product of bitumen extraction from surface-mined oil sands ores. When incubated in a laboratory under simulated moist oxic environmental conditions for ~450d, two different types of TT (TT1 and TT2) exhibited the potential to generate acid rock drainage (ARD) by producing acid leachate after 250 and 50d, respectively. We report here the release of toxic metals from TT via ARD, which could pose an environmental threat if oil sands TT deposits are not properly managed. Trace metal concentrations in leachate samples collected periodically revealed that Mn and Sr were released immediately even before the onset of ARD. Spikes in Co and Ni concentrations were observed both pre-ARD and during active ARD, particularly in TT1. For most elements measured (Fe, Cr, V, As, Cu, Pb, Zn, Cd, and Se), leaching was associated with ARD production. Though equivalent acidification (pH2) was achieved in leachate from both TT types, greater metal release was observed from TT2 where concentrations reached 10,000ppb for Ni, 5000ppb for Co, 3000ppb for As, 2000ppb for V, and 1000ppb for Cr. Generally, metal concentrations decreased in leachate with time during ARD and became negligible by the end of incubation (~450d) despite appreciable metals remaining in the leached TT. These results suggest that using TT for land reclamation purposes or surface deposition for volume reduction may unfavorably impact the environment, and warrants application of appropriate strategies for management of pyrite-enriched oil sands tailings streams. Copyright © 2016 Elsevier B.V. All rights reserved.

Origin and evolution of formation water at the Jujo-Tecominoacan oil reservoir, Gulf of Mexico. Part 1: Chemical evolution and water-rock interaction

Energy Technology Data Exchange (ETDEWEB)

Birkle, Peter, E-mail: birkle@iie.org.mx [Instituto de Investigaciones Electricas (IIE), Gerencia de Geotermia, Av. Reforma 113, Cuernavaca, Morelos 62490 (Mexico); Garcia, Bernardo Martinez; Milland Padron, Carlos M. [PEMEX Exploracion y Produccion, Region Sur, Activo Integral Bellota-Jujo, Diseno de Explotacion, Cardenas, Tabasco (Mexico)

2009-04-15

The origin and evolution of formation water from Upper Jurassic to Upper Cretaceous mudstone-packstone-dolomite host rocks at the Jujo-Tecominoacan oil reservoir, located onshore in SE-Mexico at a depth from 5200 to 6200 m.b.s.l., have been investigated, using detailed water geochemistry from 12 producer wells and six closed wells, and related host rock mineralogy. Saline waters of Cl-Na type with total dissolved solids from 10 to 23 g/L are chemically distinct from hypersaline Cl-Ca-Na and Cl-Na-Ca type waters with TDS between 181 and 385 g/L. Bromine/Cl and Br/Na ratios suggest the subaerial evaporation of seawater beyond halite precipitation to explain the extreme hypersaline components, while less saline samples were formed by mixing of high salinity end members with surface-derived, low salinity water components. The dissolution of evaporites from adjacent salt domes has little impact on present formation water composition. Geochemical simulations with Harvie-M{phi}ller-Weare and PHRQPITZ thermodynamic data sets suggest secondary fluid enrichment in Ca, HCO{sub 3} and Sr by water-rock interaction. The volumetric mass balance between Ca enrichment and Mg depletion confirms dolomitization as the major alteration process. Potassium/Cl ratios below evaporation trajectory are attributed to minor precipitation of K feldspar and illitization without evidence for albitization at the Jujo-Tecominoacan reservoir. The abundance of secondary dolomite, illite and pyrite in drilling cores from reservoir host rock reconfirms the observed water-rock exchange processes. Sulfate concentrations are controlled by anhydrite solubility as indicated by positive SI-values, although anhydrite deposition is limited throughout the lithological reservoir column. The chemical variety of produced water at the Jujo-Tecominoacan oil field is related to a sequence of primary and secondary processes, including infiltration of evaporated seawater and original meteoric fluids, the subsequent

Origin and evolution of formation water at the Jujo-Tecominoacan oil reservoir, Gulf of Mexico. Part 1: Chemical evolution and water-rock interaction

International Nuclear Information System (INIS)

Birkle, Peter; Garcia, Bernardo Martinez; Milland Padron, Carlos M.

2009-01-01

The origin and evolution of formation water from Upper Jurassic to Upper Cretaceous mudstone-packstone-dolomite host rocks at the Jujo-Tecominoacan oil reservoir, located onshore in SE-Mexico at a depth from 5200 to 6200 m.b.s.l., have been investigated, using detailed water geochemistry from 12 producer wells and six closed wells, and related host rock mineralogy. Saline waters of Cl-Na type with total dissolved solids from 10 to 23 g/L are chemically distinct from hypersaline Cl-Ca-Na and Cl-Na-Ca type waters with TDS between 181 and 385 g/L. Bromine/Cl and Br/Na ratios suggest the subaerial evaporation of seawater beyond halite precipitation to explain the extreme hypersaline components, while less saline samples were formed by mixing of high salinity end members with surface-derived, low salinity water components. The dissolution of evaporites from adjacent salt domes has little impact on present formation water composition. Geochemical simulations with Harvie-Mφller-Weare and PHRQPITZ thermodynamic data sets suggest secondary fluid enrichment in Ca, HCO 3 and Sr by water-rock interaction. The volumetric mass balance between Ca enrichment and Mg depletion confirms dolomitization as the major alteration process. Potassium/Cl ratios below evaporation trajectory are attributed to minor precipitation of K feldspar and illitization without evidence for albitization at the Jujo-Tecominoacan reservoir. The abundance of secondary dolomite, illite and pyrite in drilling cores from reservoir host rock reconfirms the observed water-rock exchange processes. Sulfate concentrations are controlled by anhydrite solubility as indicated by positive SI-values, although anhydrite deposition is limited throughout the lithological reservoir column. The chemical variety of produced water at the Jujo-Tecominoacan oil field is related to a sequence of primary and secondary processes, including infiltration of evaporated seawater and original meteoric fluids, the subsequent mixing of

Gas pressure from a nuclear explosion in oil shale

International Nuclear Information System (INIS)

Taylor, R.W.

1975-01-01

The quantity of gas and the gas pressure resulting from a nuclear explosion in oil shale is estimated. These estimates are based on the thermal history of the rock during and after the explosion and the amount of gas that oil shale releases when heated. It is estimated that for oil shale containing less than a few percent of kerogen the gas pressure will be lower than the hydrostatic pressure. A field program to determine the effects of nuclear explosions in rocks that simulate the unique features of oil shale is recommended. (U.S.)

Palynofacies characterization for hydrocarbon source rock ...

Indian Academy of Sciences (India)

source rock potential of the Subathu Formation in the area. Petroleum geologists are well aware of the fact that the dispersed organic matter derived either from marine or non-marine sediments on reach- ing its maturation level over extended period of time contributes as source material for the produc- tion of hydrocarbons.

Tectono-thermal Evolution of the Lower Paleozoic Petroleum Source Rocks in the Southern Lublin Trough: Implications for Shale Gas Exploration from Maturity Modelling

Science.gov (United States)

Botor, Dariusz

2018-03-01

The Lower Paleozoic basins of eastern Poland have recently been the focus of intensive exploration for shale gas. In the Lublin Basin potential unconventional play is related to Lower Silurian source rocks. In order to assess petroleum charge history of these shale gas reservoirs, 1-D maturity modeling has been performed. In the Łopiennik IG-1 well, which is the only well that penetrated Lower Paleozoic strata in the study area, the uniform vitrinite reflectance values within the Paleozoic section are interpreted as being mainly the result of higher heat flow in the Late Carboniferous to Early Permian times and 3500 m thick overburden eroded due to the Variscan inversion. Moreover, our model has been supported by zircon helium and apatite fission track dating. The Lower Paleozoic strata in the study area reached maximum temperature in the Late Carboniferous time. Accomplished tectono-thermal model allowed establishing that petroleum generation in the Lower Silurian source rocks developed mainly in the Devonian - Carboniferous period. Whereas, during Mesozoic burial, hydrocarbon generation processes did not develop again. This has negative influence on potential durability of shale gas reservoirs.

Inherent wettability of different rock surfaces at nanoscale: a theoretical study

Science.gov (United States)

Chang, Xiao; Xue, Qingzhong; Li, Xiaofang; Zhang, Jianqiang; Zhu, Lei; He, Daliang; Zheng, Haixia; Lu, Shuangfang; Liu, Zilong

2018-03-01

Investigating the inherent wettability of rock surfaces at nanoscale is of great importance in ore floatation and oil recovery field. Using molecular dynamics simulations, we systematically study the wetting behavior of water on different rock surfaces (silica, calcite, gypsum, halite and graphite) at nanoscale. It is demonstrated that the inherent rock wettability follows the order of gypsum > calcite > halite > silica > graphite. Remarkably, we also manifest that the polarity of oil molecules can affect the water contact angles on silica surface. For example, the water contact angles on silica surface in hexane, dodecane, thiophene and toluene are 58 ± 2°, 63 ± 3°, 90 ± 1°, 118 ± 1°, respectively. Furthermore, we investigate the wetting behavior of water on heterogeneous rock surfaces and find that water molecules can move from hydrophobic surface to hydrophilic surface.

Application of Rock-Eval pyrolysis to the detection of hydrocarbon property in sandstone-type uranium deposits

International Nuclear Information System (INIS)

Sun Ye; Li Ziying; Guo Qingyin; Xiao Xinjian

2006-01-01

Rock-Eval pyrolysis is introduced into the research of uranium geology by means of oil-gas geochemical evaluation. Hydrocarbon (oil-gas) components in DS sandstone-type uranium deposit are detected quantitatively. Through analyzing the oil-gas bearing categories of the uranium-bearing sandstones, the internal relationships between the uranium deposit and the oil-gas are revealed. Rock-Eval pyrolysis is an effective method to study the interaction between inorganic and organic matters, and should be extended to the study of sandstone-type uranium deposits. (authors)

Amorphous silica maturation in chemically weathered clastic sediments

Science.gov (United States)

Liesegang, Moritz; Milke, Ralf; Berthold, Christoph

2018-03-01

A detailed understanding of silica postdepositional transformation mechanisms is fundamental for its use as a palaeobiologic and palaeoenvironmental archive. Amorphous silica (opal-A) is an important biomineral, an alteration product of silicate rocks on the surface of Earth and Mars, and a precursor material for stable silica phases. During diagenesis, amorphous silica gradually and gradationally transforms to opal-CT, opal-C, and eventually quartz. Here we demonstrate the early-stage maturation of several million year old opal-A from deeply weathered Early Cretaceous and Ordovician sedimentary rocks of the Great Artesian Basin (central Australia). X-ray diffraction, scanning electron microscopy, and electron probe microanalyses show that the mineralogical maturation of the nanosphere material is decoupled from its chemical properties and begins significantly earlier than micromorphology suggests. Non-destructive and locally highly resolved X-ray microdiffraction (μ-XRD2) reveals an almost linear positive correlation between the main peak position (3.97 to 4.06 Å) and a new asymmetry parameter, AP. Heating experiments and calculated diffractograms indicate that nucleation and growth of tridymite-rich nanodomains induce systematic peak shifts and symmetry variations in diffraction patterns of morphologically juvenile opal-A. Our results show that the asymmetry parameter traces the early-stage maturation of amorphous silica, and that the mineralogical opal-A/CT stage extends to smaller d-spacings and larger FWHM values than previously suggested.

Increased Oil Recovery from Mature Oil Fields Using Gelled Polymer Treatments

Energy Technology Data Exchange (ETDEWEB)

Willhite, G.P.; Green, D.W.; McCool, C.S.

2001-01-22

This report describes the progress of the first year of a three-year research program. This program is aimed at reducing barriers to the widespread use of gelled polymer treatments by (1) developing methods to predict gel behavior during placement in matrix rock and fractures, (2) determining the persistence of permeability reduction after gel placement, and (3) developing methods to design production well treatments to control water production.

The tax aspects of mature fields of oil and the reduction of regional inequalities in Brazil; Aspectos fiscais dos campos maduros de petroleo e reducao das desigualdades regionais no Brasil

Energy Technology Data Exchange (ETDEWEB)

Passeggi, Alicia Violeta B.S. [Instituto Brasileiro de Petroleo, Gas e Biocombustiveis (IBP), Rio de Janeiro, RJ (Brazil); Bichara, Jahyr-Philippe [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

2008-07-01

Considering the important role played in internalizing national development by the small and medium size oil producers, the work approaches the tax aspects in the activity of mature fields' exploitation, relating it to the constitutional principle of reduction of regional inequalities, which is deeply developed in the Brazilian Federal Constitution of 1988. The birth of a new class of independent producers, in a scene before dominated by one single actor, is a phenomena that demands special attention from the State as 'regulator', because it includes several relevant aspects to the achievement of national objectives, legally imposed, such as: free enterprise, the pursuit of plain employment, the reduction of regional inequalities, a favored treatment to enterprises of small size, the conservation of energy, the rational use of oil, among others. Despite its relevance, the exploitation of mature fields suffers an absence of specific regulation, e.g., in what concern the imprecise terminology of mature fields. It was verified through the research, that the tax regime does not take into consideration neither the reduced contributive capacity of the small and medium size producers, nor its important function in the regional and energy subjects. (author)

A geochemical study of oil in metalliferous veins, Idarado Mine, San Juan Mountains, Colorado

Science.gov (United States)

Gerrild, Peter M.

1976-01-01

A tarry, benzene-soluble material is present in metal-rich veins in the Idarado mine, Ouray County, Colo., in an area not known to have petroleum resources. The material was compared chemically, spectometrically, and chromatographically with oils from four fields in the nearby Paradox basin. Each of these oil fields contains reservoir rocks equivalent to rock units known to extend beneath volcanic rocks near the mine. Carbon and sulfur isotope data and gas chromatographic data indicate a similarity between the oil from the nearby Sierra field and the oil from the mine. Thus, it seems both geologically and chemically possible that oil in the mine originated in Cretaceous sediments. Variations in the composition of oil from the mine and differences between the mine oil and Sierra oil, notably in the distributions of hydrocarbons, are attributed to bacterial degradation.

Chemical profiling of gaharu oil

International Nuclear Information System (INIS)

Mat Rasol Awang; Mohd Fajri Osman; Ahsanulkhaliqin Abd Wahab; Khairuddin Abdul Rahim; Shaiful Azuar Mohamad

2006-01-01

Gaharu oil from Aquilaria agallocha and Aquilaria malaccensis Lamk has been reported to contain different phytochemicals components (Ishihara et al., 1993). There are also differences reported by gaharu oil suppliers. The differences suggested they originate from varied of sources of gaharu wood, oleoresin maturity and extraction technology employed. In this study, gaharu oil purchased from different sources were initially analysed and later cross-examined against chemical components of oil extracted from wood sources systematically graded. The gaharu oil components obtained from this work will be presented and discussed. Initiative to profile oil provides impetus to database development and standardisation of gaharu oil. (Author)

The feasibility and prospect of uranium-gas in black rock series of joint exploration and development

International Nuclear Information System (INIS)

Xu Guochang; Zhang Dehua; Zhang Hongjian

2014-01-01

By the analysis and contrast of existing form of gas-uranium, correlation between gas-uranium and organic matter, distribution characteristics and control factors of mineralization (bosom) in the sedimentary formation of shale gas and black uranium bearing rock series, the authors come to the conclusion that: in the carbonate-siliceous-pelitic of black rock series the uranium and gas (oil) is essentially equipped coenosarc of the same homology, syngenetic, reservoir. They are ore source beds of carbonate-siliceous-pelitic rock uranium deposit, and also the hydrocarbon source beds in which the shale gas form. In black shales, uranium largely exist in the form of the ion adsorption (acetyl ion/uranyl ion). Under fracturing conditions, we can realize desorption mode of chemical solvents of adding acid or alkali, and extract uranium by concentrating liquid (the same as in-situ mimng technology). Therefore, the fracturing technology (clear water fracturing techniques, repeat fracturing techniques, synchronization fracturing techniques, multistage fracturing techniques, network fracturing techniques and so on) of shale gas exploitation lay a foundation for black shale uranium-gas joint development. The mature and corollary use of fracturing techniques and in-situ mining technology of low grade uranium will undoubtedly further increase the industrial resource extent of uranium and gas, improve guaranteeing degree of resource, reform of promote energy production structure and provide a large number of economical and effective clean energy. (authors)

Trace element characterisation of Cretaceous Orange Basin hydrocarbon source rocks

International Nuclear Information System (INIS)

Akinlua, A.; Adekola, S.A.; Swakamisa, O.; Fadipe, O.A.; Akinyemi, S.A.

2010-01-01

Research highlights: → Vanadium and nickel contents indicate that the rock samples from the Orange Basin have marine organic matter input. → The organic matter of the Orange Basin source rocks were deposited in reducing conditions. → Despite the similarities in the organic matter source input and depositional environment of the samples from the two well, cross plots of Co/Ni versus V/Ni and Mo/Ni versus Co/Ni were able to reveal their subtle differences. → Cluster analysis classified the samples into three groups based on subtle differences in their .thermal maturity. - Abstract: Trace elements in the kerogen fraction of hydrocarbon source rock samples from two wells obtained from the Cretaceous units of the Orange Basin, South Africa were determined using X-ray fluorescence spectrometry, in order to determine their distribution and geochemical significances. The concentrations of the elements (As, Ce, Co, Cu, Fe, Mo, Ni, Pb and V) determined ranged from 0.64 to 47,300 ppm for the samples analysed. The total organic carbon (TOC) values indicate that the samples are organic rich but did not show any trend with the distribution of the trace metals except Ce, Mo and Pb. Dendrogram cluster analysis discriminated the samples into three groups on the basis of their level of thermal maturity. Thermal maturity has a significant effect on the distribution of the trace metals. Cobalt/Ni and V/Ni ratios and cross plots of the absolute values of V and Ni indicate that the samples had significant marine organic matter input. The V and Ni contents and V/(V + Ni) ratio indicate that the organic matter of the source rocks had been deposited in reducing conditions. Despite the similarities in the organic matter source input and depositional environment of the organic matter of the samples from the two well, cross plots of Co/Ni versus V/Ni and Mo/Ni versus Co/Ni were able to reveal subtle differences. Cluster analysis of the samples was also able to reveal the subtle

Petroleum geochemistry of the Potwar Basin, Pakistan: II – Oil classification based on heterocyclic and polycyclic aromatic hydrocarbons

International Nuclear Information System (INIS)

Asif, Muhammad; Fazeelat, Tahira

2012-01-01

In a previous study, oils in the Potwar Basin (Upper Indus) of Pakistan were correlated based on the dissimilarity of source and depositional environment of organic matter (OM) using biomarkers and bulk stable isotopes. This study is aimed at supporting the classification of Potwar Basin oils into three groups (A, B and C) using the distribution of alkylnaphthalenes, alkylphenanthrenes, alkyldibenzothiophenes, alkyldibenzofurans, alkylfluorenes, alkylbiphenyls, triaromatic steroids, methyl triaromatic steroids, retene, methyl retenes and cadalene. The higher relative abundance of specific methyl isomers of naphthalene and phenanthrene and the presence of diagnostic aromatic biomarkers clearly indicate the terrigenous and oxic depositional environment of OM for group A oil. Group B and C oils are of marine origin and the aforementioned heterocyclic and polycyclic aromatic hydrocarbons (HCs) differentiate them clearly into two different groups. The relative percentages of heterocyclic aromatic HCs reveal that the distribution of these compounds is controlled by the depositional environment of the OM. Sulfur-containing heterocyclic aromatic HCs are higher in crude oils generated from source rocks deposited in suboxic depositional environments, while oxygen-containing heterocyclic aromatic HCs in combination with alkylfluorenes are higher in marine oxic and deltaic oils. Biomarker and aromatic HC parameters do not indicate significant differences in the thermal maturity of Potwar Basin oils. Triaromatic and methyl triaromatic steroids support the division of Potwar Basin oils into the three groups and their relative abundances are related to source OM rather than thermal maturity. Significantly higher amounts of C 20 and C 21 triaromtic steroids and the presence or absence of long chain triaromatic steroids (C 25 , C 26 , C 27 , and C 28 ) indicates that these compounds are probably formed from different biological precursors in each group. Different isomers of methyl

Subsurface Analysis of the Mesaverde Group on and near the Jicarilla Apache Indian Reservation, New Mexico-its implication on Sites of Oil and Gas Accumulation

Energy Technology Data Exchange (ETDEWEB)

Ridgley, Jennie

2001-08-21

The purpose of the phase 2 Mesaverde study part of the Department of Energy funded project ''Analysis of oil-bearing Cretaceous Sandstone Hydrocarbon Reservoirs, exclusive of the Dakota Sandstone, on the Jicarilla Apache Indian Reservation, New Mexico'' was to define the facies of the oil-producing units within the subsurface units of the Mesaverde Group and integrate these results with outcrop studies that defined the depositional environments of these facies within a sequence stratigraphic context. The focus of this report will center on (1) integration of subsurface correlations with outcrop correlations of components of the Mesaverde, (2) application of the sequence stratigraphic model determined in the phase one study to these correlations, (3) determination of the facies distribution of the Mesaverde Group and their relationship to sites of oil and gas accumulation, (4) evaluation of the thermal maturity and potential source rocks for oil and gas in the Mesaverde Group, and (5) evaluation of the structural features on the Reservation as they may control sites of oil accumulation.

Imaging of forced-imbibition in carbonate rocks using synchrotron X-ray micro-tomography

Science.gov (United States)

Singh, K.; Menke, H. P.; Andrew, M. G.; Lin, Q.; Saif, T.; Al-Khulaifi, Y.; Reynolds, C. A.; Bijeljic, B.; Rau, C.; Blunt, M. J.

2016-12-01

We have investigated the pore-scale behavior of brine-oil systems and oil trapping during forced-imbibition in a water-wet carbonate rock in a capillary-dominated flow regime at reservoir pressure conditions. To capture the dynamics of the brine-oil front progression and snap-off process, real-time tomograms with a time resolution of 38 s (24 s for imaging and 14 s for recording the data) and a spatial resolution of 3.28 µm were acquired at Diamond Light Source (UK). The data were first analyzed at global scale (complete imaged rock) for overall front behavior. From the saturation profiles, we obtain the location of the tail of the desaturation front that progresses with a velocity of 13 µm/min. This velocity is smaller than average flow velocity 16.88 µm/min, which explains why it needs slightly more than 1 pore volume of brine injection to reach the residual saturation of oil in a water-wet rock. The data were further analyzed at local scale to investigate the pore-scale mechanisms of oil trapping during brine flooding. We isolated various trapping events which resulted in the creation of discrete oil ganglia occupying one to several pore bodies. We perform pore-scale curvature analysis of brine-oil interfaces to obtain local capillary pressure that will be related to the shape and the size of throats in which ganglia were trapped.

Hydrocarbon Source Rock Potential of the Sinamar Formation, Muara Bungo, Jambi

Directory of Open Access Journals (Sweden)

Moh. Heri Hermiyanto Zajuli

2014-07-01

Full Text Available DOI: 10.17014/ijog.v1i1.175The Oligocene Sinamar Formation consists of shale, claystone, mudstone, sandstone, conglomeratic sandstone, and intercalation of coal seams. The objective of study was to identify the hydrocarbon source rock potential of the Sinamar Formation based on geochemichal characteristics. The analyses were focused on fine sediments of the Sinamar Formation comprising shale, claystone, and mudstone. Primary data collected from the Sinamar Formation well and outcrops were analyzed according to TOC, pyrolisis analysis, and gas chromatography - mass spectometry of normal alkanes that include isoprenoids and sterane. The TOC value indicates a very well category. Based on TOC versus Pyrolysis Yields (PY diagram, the shales of Sinamar Formation are included into oil prone source rock potential with good to excellent categories. Fine sediments of the Sinamar Formation tend to produce oil and gas originated from kerogen types I and III. The shales tend to generate oil than claystone and mudstone and therefore they are included into a potential source rock. 

Can reserve additions in mature crude oil provinces attenuate peak oil?

NARCIS (Netherlands)

Okullo, S.J.; Reynes, F.G.D.

2011-01-01

Following the peak in US crude oil production 30 years ago, more and more non-OPEC producers have seen their production decline as a result of resource depletion. OPEC, on the other hand has extracted a comparatively smaller proportion of its reserve base. Given that new non-OPEC discoveries are

Regional assessments of the hydrocarbon generation potential of selected North American proterozoic rock sequences. Progress report, September 1989--April 1990

Energy Technology Data Exchange (ETDEWEB)

Engel, M.H.; Elmore, R.D.

1990-04-01

Our primary research objectives for the first year of this grant are nearing completion. This includes comprehensive sedimentologic/organic geochemical studies of two depositionally distinct, unmetamorphosed units, the Nonesuch Formation ({approximately}1.1 Ga lacustrine rift deposit) and the Dripping Spring Quartzite ({approximately}1.3 Ga marine shelf deposit). As discussed in this progress report, an attempt has been made to (1) identify source rocks by quantification and characterization of constituent organic matter, (2) recognize depositional/diagenetic/catagenetic factors that may have influenced source rock quality and (3) evaluate the possibility of previous or current hydrocarbon generation and migration. Organic petrology and geochemical analyses suggest important differences between kerogens in the Michigan (MI) and Wisconsin (WI) Nonesuch Formation study areas. When considered within a geographic/stratigraphic framework, the Nonesuch Formation in the MI study area exhibits superior source rock potential. It is suggested that sedimentary organic matter in the WI area was subject to more extensive microbial alteration during early diagenesis. It is also possible that thermal maturity levels were slightly to moderately higher in WI than MI. Petrologic evidence for migrated bitumens and the stable isotope composition of late vein carbonates suggest, furthermore, that oil generation and migration may have actually been more extensive in the WI study area.

Detailed north-south cross section showing environments of deposition, organic richness, and thermal maturities of lower Tertiary rocks in the Uinta Basin, Utah

Science.gov (United States)

Johnson, Ronald C.

2014-01-01

The Uinta Basin of northeast Utah has produced large amounts of hydrocarbons from lower Tertiary strata since the 1960s. Recent advances in drilling technologies, in particular the development of efficient methods to drill and hydraulically fracture horizontal wells, has spurred renewed interest in producing hydrocarbons from unconventional low-permeability dolomite and shale reservoirs in the lacustrine, Eocene Green River Formation. The Eocene Green River Formation was deposited in Lake Uinta, a long-lived saline lake that occupied the Uinta Basin, the Piceance Basin to the east, and the intervening Douglas Creek arch. The focus of recent drilling activity has been the informal Uteland Butte member of the Green River Formation and to a much lesser extent the overlying R-0 oil shale zone of the Green River Formation. Initial production rates ranging from 500 to 1,500 barrels of oil equivalent per day have been reported from the Uteland Butte member from horizontal well logs that are as long as 4,000 feet (ft);. The cross section presented here extends northward from outcrop on the southern margin of the basin into the basin’s deep trough, located just south of the Uinta Mountains, and transects the area where this unconventional oil play is developing. The Monument Butte field, which is one of the fields located along this line of section, has produced hydrocarbons from conventional sandstone reservoirs in the lower part of the Green River Formation and underlying Wasatch Formation since 1981. A major fluvial-deltaic system entered Lake Uinta from the south, and this new line of section is ideal for studying the effect of the sediments delivered by this drainage on hydrocarbon reservoirs in the Green River Formation. The cross section also transects the Greater Altamont-Bluebell field in the deepest part of the basin, where hydrocarbons have been produced from fractured, highly overpressured marginal lacustrine and fluvial reservoirs in the Green River, Wasatch

The investment challenges facing the oil and gas industry

International Nuclear Information System (INIS)

Suellentrop, Steve

1998-01-01

In considering the potential of the United Kingdom for investment in the oil and gas industry, four factors are discussed. They are: the importance of certainty in identifying markets; the importance of infrastructure in assisting follow-on developments in mature oil and gas fields; the UK's competitive position in the world investment market; fiscal terms in the UK as compared with those offered by other countries. The conclusion drawn is that the UK needs to be responsive to its status as a mature oil and gas area and have the flexibility to stimulate investment in frontier areas. Stability in both the fiscal regime and also handling issues like market access is important. There is a need to capitalise on the many advantages conferred by the existing infrastructure in mature areas. (UK)

Development of Polymer Gel Systems to Improve Volumetric Sweep and Reduce Producing Water/Oil Ratios

Energy Technology Data Exchange (ETDEWEB)

G. Paul Willhite; Stan McCool; Don W. Green; Min Cheng; Feiyan Chen

2005-12-31

to water to a greater extent than the permeability to oil is reduced. This phenomenon is referred to as disproportionate permeability reduction (DPR). Flow experiments were conducted in sandpacks to determine the effect of polymer and chromium concentrations on DPR. All gels studied reduced the permeability to water by a greater factor than the factor by which the oil permeability was reduced. Greater DPR was observed as the concentrations of polymer and chromium were increased. A conceptual model of the mechanisms responsible for DPR is presented. Primary features of the model are (1) the development of flow channels through the gel by dehydration and displacement of the gel and by re-connection of pre-treatment, residual oil volume and (2) high flow resistance in the channels during water flow is caused by significant saturations of oil remaining in the channels. A similar study of DPR was conducted in Berea sandstone cores. Both oil and water permeabilities were reduced by much smaller factors in Berea sandstone cores than in similar treatments in sandpacks. Poor maturation of the gelant in the Berea rock was thought to be caused by fluid-rock interactions that interfered with the gelation process.

Advances and Applications of Rock Physics for Hydrocarbon Exploration

Directory of Open Access Journals (Sweden)

Valle-Molina C.

2012-10-01

Full Text Available Integration of the geological and geophysical information with different scale and features is the key point to establish relationships between petrophysical and elastic characteristics of the rocks in the reservoir. It is very important to present the fundamentals and current methodologies of the rock physics analyses applied to hydrocarbons exploration among engineers and Mexican students. This work represents an effort to capacitate personnel of oil exploration through the revision of the subjects of rock physics. The main aim is to show updated improvements and applications of rock physics into seismology for exploration. Most of the methodologies presented in this document are related to the study the physical and geological mechanisms that impact on the elastic properties of the rock reservoirs based on rock specimens characterization and geophysical borehole information. Predictions of the rock properties (litology, porosity, fluid in the voids can be performed using 3D seismic data that shall be properly calibrated with experimental measurements in rock cores and seismic well log data

X-ray microtomography application in pore space reservoir rock.

Science.gov (United States)

Oliveira, M F S; Lima, I; Borghi, L; Lopes, R T

2012-07-01

Characterization of porosity in carbonate rocks is important in the oil and gas industry since a major hydrocarbons field is formed by this lithology and they have a complex media porous. In this context, this research presents a study of the pore space in limestones rocks by x-ray microtomography. Total porosity, type of porosity and pore size distribution were evaluated from 3D high resolution images. Results show that carbonate rocks has a complex pore space system with different pores types at the same facies. Copyright © 2011 Elsevier Ltd. All rights reserved.

Reservoir characterization and monitoring of cold and thermal heavy oil production using multi-transient EM

Energy Technology Data Exchange (ETDEWEB)

Engelmark, F. [Petroleum Geo-Services Asia Pacific Pte Ltd., Singapore (Singapore)

2008-10-15

This study emphasized the importance of mapping the in situ subsurface distribution of heavy oil for evaluating the amount of oil in place. The multi-transient electromagnetic (MTEM) method was shown to be an ideal method to characterize the large scale distribution of oil, including the average saturation levels, on the scale needed to optimize oil extraction using steam assisted gravity drainage (SAGD) and cyclic steam stimulation (CSS). A feasibility study for an MTEM monitoring project would simulate reservoir temperature, water saturation and salinity to determine the evolution over time expressed in resistivity and the expanding steam chamber. The 4 factors influencing the resistivity in the monitoring phase were discussed. The temperature due to steaming causes a significant drop in resistivity of the affected rock volume, while the changes in water saturation affect resistivity. The drop in salinity of the pore water due to mixing with distilled water originating in the condensation of the injected steam causes an increase in resistivity, while the mineral dissolution and overall volume expansion causes formation damage that permanently changes the rock fabric. The overall effect of steam injection is a reduction in resistivity within the main part of the chamber, with a sudden increase in resistivity in the proximity of the injection well due to salt depletion. The lowered resistivity within a halo outside the steam chamber can be attributed to the heat radiation front expanding faster than the maturing steam chamber. The author noted that reservoir simulators do not yet incorporate the dynamic changes in porosity and permeability that are observed as permanent reductions of the elastic moduli and reduced resistivity. It was concluded that in order to fully describe the evolution of the steam chamber, this so called formation damage must be better understood. 6 refs., 7 figs.

Performance evaluation of a natural treatment system for small communities, composed of a UASB reactor, maturation ponds (baffled and unbaffled) and a granular rock filter in series.

Science.gov (United States)

Dias, D F C; Passos, R G; Rodrigues, V A J; de Matos, M P; Santos, C R S; von Sperling, M

2018-02-01

Post-treatment of anaerobic reactor effluent with maturation ponds is a good option for small to medium-sized communities in tropical climates. The treatment line investigated, operating in Brazil, with an equivalent capacity to treat domestic sewage from 250 inhabitants, comprised a upflow anaerobic sludge blanket reactor followed by two shallow maturation ponds (unbaffled and baffled) and a granular rock filter (decreasing grain size) in series, requiring an area of only 1.5 m 2  inhabitant -1 . With an overall hydraulic retention time of only 6.7 days, the performance was excellent for a natural treatment system. Based on over two years of continuous monitoring, median removal efficiencies were: biochemical oxygen demand = 93%, chemical oxygen demand = 79%, total suspended solids = 87%, ammonia = 43% and Escherichia coli = 6.1 log units. The final effluent complied with European discharge standards and WHO guidelines for some forms of irrigation, and appeared to be a suitable alternative for treating domestic sewage for small communities in warm areas, especially in developing countries.

An insight into the mechanism and evolution of shale reservoir characteristics with over-high maturity

Directory of Open Access Journals (Sweden)

Xinjing Li

2016-10-01

Full Text Available Over-high maturity is one of the most vital characteristics of marine organic-rich shale reservoirs from the Lower Paleozoic in the south part of China. The organic matter (OM in shale gas reservoirs almost went through the entire thermal evolution. During this wide span, a great amount of hydrocarbon was available and numerous pores were observed within the OM including kerogen and solid bitumen/pyrobitumen. These nanopores in solid bitumen/pyrobitumen can be identified using SEM. The imaging can be dissected and understood better based on the sequence of diagenesis and hydrocarbon charge with the shape of OM and pores. In terms of the maturity process showed by the various typical cases, the main effects of the relationship between the reservoir porosity and organic carbon abundance are interpreted as follows: the change and mechanism of reservoirs properties due to thermal evolution are explored, such as gas carbon isotope from partial to complete rollover zone, wettability alteration from water-wet to oil-wet and then water-wet pore surface again, electrical resistivity reversal from the increasing to decreasing stage, and nonlinearity fluctuation of rock elasticity anisotropy. These indicate a possible evolution pathway for shale gas reservoirs from the Lower Paleozoic in the southern China, as well as the general transformation processes between different shale reservoirs in thermal stages.

Research on oil recovery mechanisms in heavy oil reservoirs

Energy Technology Data Exchange (ETDEWEB)

Kovscek, Anthony R.; Brigham, William E., Castanier, Louis M.

2000-03-16

The research described here was directed toward improved understanding of thermal and heavy-oil production mechanisms and is categorized into: (1) flow and rock properties, (2) in-situ combustion, (3) additives to improve mobility control, (4) reservoir definition, and (5) support services. The scope of activities extended over a three-year period. Significant work was accomplished in the area of flow properties of steam, water, and oil in consolidated and unconsolidated porous media, transport in fractured porous media, foam generation and flow in homogeneous and heterogeneous porous media, the effects of displacement pattern geometry and mobility ratio on oil recovery, and analytical representation of water influx.

Origin of late pleistocene formation water in Mexican oil reservoirs

Energy Technology Data Exchange (ETDEWEB)

Birkle, P. [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

2004-07-01

Brine water invasion into petroleum reservoirs, especially in sedimentary basins, are known from a variety of global oil field, such as the Western Canada sedimentary basin and, the central Mississippi Salt Dome basin (Kharaka et al., 1987). The majority of oil wells, especially in the more mature North American fields, produce more water than they do oil (Peachey et al., 1998). In the case of Mexican oil fields, increasing volumes of invading water into the petroleum wells were detected during the past few years. Major oil reserves in the SE-part of the Gulf of Mexico are economically affected due to decreases in production rate, pipeline corrosion and well closure. The origin of deep formation water in many sedimentary basins is still controversial: Former hypothesis mainly in the 60's, explained the formation of formation water by entrapment of seawater during sediment deposition. Subsequent water-rock interaction processes explain the chemical evolution of hydrostatic connate water. More recent hydrodynamic models, mainly based on isotopic data, suggest the partial migration of connate fluids, whereas the subsequent invasion of surface water causes mixing processes (Carpenter 1978). As part of the presented study, a total of 90 oil production wells were sampled from 1998 to 2004 to obtain chemical (Major and trace elements) and isotopic composition ({sup 2}H, {sup 13}C, {sup 14}C, {sup 18}O {sup 36}Cl, {sup 37}Cl, {sup 87}Sr, {sup 129}I, tritium) of deep formation water at the Mexican Gulf coast. Samples were extracted from carbonate-type reservoirs of the oil fields Luna, Samaria-Sitio Grande, Jujo-Tecominoac (on-shore), and Pol-Chuc (off-shore, including Abkatun, Batab, Caan, and Taratunich) at a depth between 2,900 m b.s.l. and 6,100 m b.s.l. During the field work, the influence of atmospheric contamination e.g. by CO{sub 2}-atmospheric input was avoided by using an interval sampler to get in-situ samples from the extraction zone of selected bore holes

Geology and oil and gas assessment of the Mancos-Menefee Composite Total Petroleum System: Chapter 4 in Total petroleum systems and geologic assessment of undiscovered oil and gas resources in the San Juan Basin Province, exclusive of Paleozoic rocks, New Mexico and Colorado

Science.gov (United States)

Ridgley, J.L.; Condon, S.M.; Hatch, J.R.

2013-01-01

The Mancos-Menefee Composite Total Petroleum System (TPS) includes all genetically related hydrocarbons generated from organic-rich shales in the Cretaceous Mancos Shale and from carbonaceous shale, coal beds, and humate in the Cretaceous Menefee Formation of the Mesaverde Group. The system is called a composite total petroleum system because the exact source of the hydrocarbons in some of the reservoirs is not known. Reservoir rocks that contain hydrocarbons generated in Mancos and Menefee source beds are found in the Cretaceous Dakota Sandstone, at the base of the composite TPS, through the lower part of the Cliff House Sandstone of the Mesaverde Group, at the top. Source rocks in both the Mancos Shale and Menefee Formation entered the oil generation window in the late Eocene and continued to generate oil or gas into the late Miocene. Near the end of the Miocene in the San Juan Basin, subsidence ceased, hydrocarbon generation ceased, and the basin was uplifted and differentially eroded. Reservoirs are now underpressured.

Use of Oil-Based Mud Cutting Waste in Cement Clinker Manufacturing

OpenAIRE

Saif Al-Dhamri, H; Black, L

2014-01-01

Oil-based Mud (OBM) cutting waste is generated during the process of oil well drilling. The drilled rocks are removed from deep within the drilled well and pumped to the surface. The portion removed , known at "cutting", is a mixture of rocks, mud, water and oil. Most drilling companies store this waste in open yards with no specific treatment solution. The environmental regulations in Oman specify that storage should involve isolation, to prevent penetration of the contamination to the surfa...

Fluid-Rock Characterization and Interactions in NMR Well Logging

Energy Technology Data Exchange (ETDEWEB)

Hirasaki, George J.; Mohanty, Kishore K.

2003-02-10

The objective of this project was to characterize the fluid properties and fluid-rock interactions that are needed for formation evaluation by NMR well logging. The advances made in the understanding of NMR fluid properties are summarized in a chapter written for an AAPG book on NMR well logging. This includes live oils, viscous oils, natural gas mixtures, and the relation between relaxation time and diffusivity.

Macroscopic Rock Texture Image Classification Using a Hierarchical Neuro-Fuzzy Class Method

Directory of Open Access Journals (Sweden)

Laercio B. Gonçalves

2010-01-01

Full Text Available We used a Hierarchical Neuro-Fuzzy Class Method based on binary space partitioning (NFHB-Class Method for macroscopic rock texture classification. The relevance of this study is in helping Geologists in the diagnosis and planning of oil reservoir exploration. The proposed method is capable of generating its own decision structure, with automatic extraction of fuzzy rules. These rules are linguistically interpretable, thus explaining the obtained data structure. The presented image classification for macroscopic rocks is based on texture descriptors, such as spatial variation coefficient, Hurst coefficient, entropy, and cooccurrence matrix. Four rock classes have been evaluated by the NFHB-Class Method: gneiss (two subclasses, basalt (four subclasses, diabase (five subclasses, and rhyolite (five subclasses. These four rock classes are of great interest in the evaluation of oil boreholes, which is considered a complex task by geologists. We present a computer method to solve this problem. In order to evaluate system performance, we used 50 RGB images for each rock classes and subclasses, thus producing a total of 800 images. For all rock classes, the NFHB-Class Method achieved a percentage of correct hits over 73%. The proposed method converged for all tests presented in the case study.

Activity of Ocimum basilicum, Ocimum canum, and Cymbopogon citratus essential oils against Plasmodium falciparum and mature-stage larvae of Anopheles funestus s.s.

Directory of Open Access Journals (Sweden)

Akono Ntonga Patrick

2014-01-01

Full Text Available The biological activities of essential oils from three plants grown in Cameroon: Ocimum basilicum, Ocimum canum, and Cymbopogon citratus were tested against Plasmodium falciparum and mature-stage larvae of Anopheles funestus. Gas chromatography and gas chromatography – mass spectrometry analyses showed that the main compounds are geranial, 1,8-cineole and linalool in C. citratus, O. canum and O. basilicum, respectively. Larvicidal tests carried out according to the protocol recommended by the World Health Organization showed that the essential oil of leaves of C. citratus is the most active against larvae of An. funestus (LC50 values = 35.5 ppm and 34.6 ppm, respectively, for larval stages III and IV after 6 h of exposure. Besides, the in vitro anti-plasmodial activity evaluated by the radioisotopic method showed that the C. citratus oil is the most active against P. falciparum, with an IC50 value of 4.2 ± 0.5 μg/mL compared with O. canum (20.6 ± 3.4 μg/mL and O. basilicum (21 ± 4.6 μg/mL. These essential oils can be recommended for the development of natural biocides for fighting the larvae of malaria vectors and for the isolation of natural products with anti-malarial activity.

Geochemical characterization of the hydrous pyrolysis products from a recent cyanobacteria-dominated microbial mat

Energy Technology Data Exchange (ETDEWEB)

Franco, N.; Mendoça-Filho, J.G.; Silva, T.F.; Stojanovic, K.; Fontana, L.F.; Carvalhal-Gomes, S.B.V.; Silva, F.S.; Furukawa, G.G.

2016-07-01

Hydrous pyrolysis experiments were performed on a recent microbial mat sample from Lagoa Vermelha, Brazil, to determine whether crude oil can be generated and expelled during artificial maturation of the Organic Matter (OM). The experiments were conducted at 280ºC, 330ºC and 350ºC during 20h. Two types of liquid pyrolysis products, assigned as free oil and bitumen, were isolated and analyzed. Free oil represents free organic phase released by hydrous pyrolysis, whereas bitumen was obtained by extraction from the solid pyrolysis residue with dichloromethane. Changes in the OM maturity were determined using Rock-Eval parameters and biomarker maturity ratios of original sample and pyrolysis products. Biomarker compositions of original sample extract and liquid pyrolysates were used for determination of dominant bacterial source. The yields of free oil and bitumen showed that a microbial mat OM has a high liquid hydrocarbons generation potential. Rock-Eval maturity parameters, biopolymer and biomarker compositions indicate a significant increase of the OM maturity during hydrous pyrolysis. At 280ºC the release of free, adsorbed and occluded compounds was observed; however, without a cracking of the OM. At 330ºC the generation of bitumen and free oil is mostly related to the OM cracking. The highest yield of free oil was recorded at this temperature. Distribution of biomarkers in the extract of original sample and liquid pyrolysates confirms cyanobacteria-dominated microbial mats, whereas the identification of long chain n-alkane series, with maximum at C26, and prominent C30 hop-17(21)-ene additionally suggest the presence of sulfate reducing bacteria. (Author)

Multiscale properties of unconventional reservoir rocks

Science.gov (United States)

Woodruff, W. F.

A multidisciplinary study of unconventional reservoir rocks is presented, providing the theory, forward modeling and Bayesian inverse modeling approaches, and laboratory protocols to characterize clay-rich, low porosity and permeability shales and mudstones within an anisotropic framework. Several physical models characterizing oil and gas shales are developed across multiple length scales, ranging from microscale phenomena, e.g. the effect of the cation exchange capacity of reactive clay mineral surfaces on water adsorption isotherms, and the effects of infinitesimal porosity compaction on elastic and electrical properties, to meso-scale phenomena, e.g. the role of mineral foliations, tortuosity of conduction pathways and the effects of organic matter (kerogen and hydrocarbon fractions) on complex conductivity and their connections to intrinsic electrical anisotropy, as well as the macro-scale electrical and elastic properties including formulations for the complex conductivity tensor and undrained stiffness tensor within the context of effective stress and poroelasticity. Detailed laboratory protocols are described for sample preparation and measurement of these properties using spectral induced polarization (SIP) and ultrasonics for the anisotropic characterization of shales for both unjacketed samples under benchtop conditions and jacketed samples under differential loading. An ongoing study of the effects of kerogen maturation through hydrous pyrolysis on the complex conductivity is also provided in review. Experimental results are catalogued and presented for various unconventional formations in North America including the Haynesville, Bakken, and Woodford shales.

Crude operators: the future of the oil industry

International Nuclear Information System (INIS)

Rowell, Andrew.

1997-01-01

Technological advances and the maturity of existing oil fields have spurred oil companies to explore for oil and extract it from previously inaccessible or ''frontier'' areas, both offshore and onshore. In many cases, such prospecting and production will have severe environmental impacts and serious social, ethical and cultural consequences. The challenge is not just to halt such exploration and extraction, but to halt oil consumption itself. (author)

A Thermal Maturity Analysis of the Effective Cretaceous Petroleum System in the Southern Persian Gulf Basin

Directory of Open Access Journals (Sweden)

Majid Alipour

2017-10-01

Full Text Available Commercial hydrocarbon discoveries in the Cretaceous of the southern Persian Gulf basin provide direct evidence that there is an effective petroleum system associated with the Cretaceous series. The revised models of thermal maturity in this region are needed to investigate lateral and stratigraphic variations of thermal maturity, which have not so far been addressed in detail for this part of the Persian Gulf. Such thermal maturity models are required to delineate the existing play assessment risks and to predict properties in more deeply buried undrilled sections. This study uses two dimensional basin modeling techniques to reconstruct maturity evolution of the Cenomanian Middle Sarvak source rock, presumably the most likely source for these hydrocarbons. The results indicate that an estimated 900 meter difference in the depth of burial between the southeastern high and the adjacent trough tends to be translated into noticeable variations at both temperature (135 °C versus 162 °C and vitrinite reflectance (0.91% versus 1.35%. Since the organic matter in the mentioned source rock is of reactive type II, these could cause a shift of about 18 million years in the onset of hydrocarbon generation over respective areas.

Organic petrology and Rock-Eval characteristics in selected surficial samples of the Tertiary Formation, South Sumatra Basin

Directory of Open Access Journals (Sweden)

M. H. Hermiyanto

2014-06-01

Full Text Available http://dx.doi.org/10.17014/ijog.vol4no3.20096Organic petrologic data of the DOM of Talangakar and Muaraenim Formations show that the organic matter consisting mainly of vitrinite group is essentially composed of telocollinite (1.0 – 70.8 % and desmocollinite (0.8 – 66.6 % with minor telinite (0.6 – 9.4 %, detrovitrinite (0.6 – 6.0 %, and cor- pocollinite (0.6 – 2.0 %. Minor exinite (0.4 – 7.8 % and inertinite (0.4 – 8.0 % are also determined. However, mineral matter varies from 0.6 – 99.44 %. Downwards, the increase in vitrinite reflectance (0.33 – 0.48 % is concomitant with the depth of each formation. Furthermore, based on Rock-eval pyrolysis, TOC value of the Talangakar Formation ranges from 0.09 – 15.38 %, Gumai 0.34 – 0.39 %, Airbenakat 0.32 – 4.82 %, and Muaraenim between 0.08 – 15.22 %. Moreover the PY (Potential Yield value variation of the Talangakar, Gumai, Airbenakat, and Muaraenim Formations are between 0.04 – 36.61 mg HC/g rock, 0.53 – 0.81 mg HC/g rock, 0.1 – 4.37 mg HC/g rock, and 0.07 – 129.8 mg HC/g rock respectively. Therefore, on the basis of those two parameters, the four formations are included into a gas - oil prone source rock potential. However, the Talangakar and Muaraenim Formations are poor to excellent category, whereas the Air Benakat tends to indicate a poor – fair category and Gumai Formation are only within a poor category. Tmax value of the Talangakar ranges from 237 – 4380 C, Gumai 316 – 3590 C, Airbenakat 398 – 4340 C with exceptions of 4970 C and 5180 C, and Muaraenim Forma- tions 264 – 4250 C. The Talangakar Formation contains kerogen Type II dan III, with the HI (Hydrogen Index value varies from 45.16 – 365.43. However two samples show value of 0. The organic content of the Gumai and Air Benakat Formations are included into kerogen type III, with HI value ranges from11.87 – 40.82, and 19 – 114 respectively. Moreover the Muaraenim Formation has two category of

Organic geochemistry of oils and condensates in the Kekeya field, southwest depression of the Tarim Basin (China)

Energy Technology Data Exchange (ETDEWEB)

Maowen Li; Snowdon, L.R. [Geological Survey of Canada, Calgary (Canada); Renzi Lin; Peirong Wang [Jianghan Petroleum Institute, Hubei (China); Yongsheng Liao; Peilong Li [Shengli Petroleum Administrative Bureau, Shandong (China)

1999-07-01

This study shows that the oils and condensates in the Kekeya Field in the Tarim Basin, NW China, belong to a single family, most likely derived from marine shale source rocks deposited under oxic-suboxic conditions with mixed terrigenous and algal-bacterial organic inputs. The maturity data clearly indicate that the paraffinic condensates were not formed by thermal cracking of oil during late catagenesis (R{sub o} > 1.2%). Both the oils and condensates were generated within the normal oil window, whereas addition of gaseous hydrocarbons from a separate source resulted in migration fractionation and hence spuriously high heptane indices. Age specific biomarkers show that the oils and condensates were not generated from the Mesozoic-Cenozoic strata, but from the Carboniferous-Permian sections. 1D basin modelling results are consistent with this interpretation, suggesting that the Mesozoic-Eocene strata are currently immature with respect to hydrocarbon generation and expulsion. Deep-seated faults may have provided routes for upward fluid migration at the time of active deformation during several pulses of the Himalayan orogeny. The favoured targets for further petroleum exploration in front of the Kunlun Mountains include the deep structures within the Carboniferous-Permian strata for indigenous petroleum accumulations and anticlines and stratigraphic traps within the Mesozoic-Cenozoic sections that are cut by deep-seated thrust faults where secondary petroleum accumulations most likely occurred. (author)

Formation of the oil composition of the Yu0 Bazhenov formation, Salym oil field

Directory of Open Access Journals (Sweden)

E.V. Soboleva

2017-05-01

Full Text Available The Bazhenov horizon of Western Siberia has been studied in considerable detail from different perspectives and different methods, a large number of studies have been devoted to a wide range of issues related to the lithological composition of rocks, their reservoir properties, the study of organic matter, properties and composition of oil at various analytical levels, and many others. This work is devoted to restoring conditions for the formation of oil properties and composition of the Yu0 Salym oil field, based mainly on the geochemical aspects of the study of oil changes both in area and in the section within the productive layer of Salym structure, using some geological data, such as structural plan for the reflecting horizon B (the roof of the Bazhenov formation, having a complex configuration, reservoir temperatures and pressure, well flow rates, and others. There is no single reservoir at the Salym field in the Yu0 formation. For the conclusions of the geological-geochemical interpretation, a sampling of 61 samples of oil from exploration, appraisal and production wells of the initial stages of production was used, since in the future when oil is extracted, the ecology in the deposits changes, and 21 samples of oil from other fields in the West Siberian oil and gas basin. Conventionally, three types of oils are distinguished, differing in their physicochemical parameters, group hydrocarbon and molecular composition. It was suggested that in addition to the own organic matter of the Bazhenov formation, hydrocarbon fluids of the Vasyugan, Tyumen formations and possibly Paleozoic rocks were involved in the formation of the oil composition. The flow of light liquid hydrocarbons and gases occurred along the zones of faults of different genesis and duration of existence.

Mature fine tailings from oil sands processing harbour diverse methanogenic communities

Energy Technology Data Exchange (ETDEWEB)

Penner, T.J.; Foght, J.M. [Alberta Univ., Edmonton, AB (Canada). Dept. of Biological Sciences

2010-06-15

Syncrude's bitumen extraction process produces a fine tailings slurry consisting of water, sand, fines, residual bitumen and naphtha diluent. Following rapid settling of the sand fraction, the tailings are stored in large settling ponds to form a thick mature fine tailings (MFT). This paper discussed the potential benefits of methane production on management of the settling basins. Enhanced methanogenesis accelerates densification and improves the rheological properties of MFT. In this study molecular techniques were used to characterize the methanogenic communities in uncultivated MFT samples to determine the diversity present in the Mildred Lake Settling Basin (MLSB) and West In-Pit tailings deposit. The flux of methane is currently estimated at about 40 million L/day at the MLSB. Clone libraries of amplified archaeal and bacterial 16S rRNA genes were created in order to analyze the methanogenic consortia in MFT samples from depth profiles in the 2 tailings deposits. The archaeal sequences, whose closest matches were primarily cultivated methanogens, were comparable within and between basins and were mostly affiliated with acetoclastic Methanosaeta spp. However, bacterial clone libraries were diverse, with most sequences relating to Proteobacteria, including some presumptive nitrate-, iron-, or sulfate-reducing, hydrocarbon-degrading genera. The study showed that MFT consists of a diverse community of prokaryotes that may be responsible for producing methane from substrates indigenous to the MFT. These findings contribute to a better understanding of the biogenesis of methane and densification of MFT in oil sands tailings deposits. The results from this study will help determine strategies to control and exploit microbial activities in these large systems and improve the understanding of methanogenic environments. 43 refs., 2 tabs., 3 figs.

) Organic Facies Variations in the Middle Cretaceous Black Shales of the Abakaliki Fold Belt, South-East, Nigeria

International Nuclear Information System (INIS)

Ehinola, O. A.; Badejoko, T.A.; Ekweozor, C.M.; Adebowale, K. O.

2003-01-01

An assessment, based on organic facies characteristics, have been carried out on the middle Cretaceous black shales, in order to determine their hydrocarbon source potential, thermal maturity, and depositional environments. The methods employed include evaluation of organic carbon content, rockeval pyrolysis, extractable organic matter, maceral composition and biomarker distributions.Organic facies criteria such as TOC, HI, Tmax, liptinite content, SOMIFOC and SHC/AHC indicate that Albian to middle Cenomanian shales are could only generate gas. The late Cenomanian to early Turonian shales are characterized by Type I/II kerogen, mature and could generate both oil and characterized by Type III kerogen, immature and could generate gas with little oil. The biomarker distributions indicate immature to mature source rock, moderately biodegraded and with reduced marine environment prevailing during the deposition of the lack shales. The late Cenomanian to early Turonian black shales show the highest source-rock potential

Improved characterization of reservoir behavior by integration of reservoir performances data and rock type distributions

Energy Technology Data Exchange (ETDEWEB)

Davies, D.K.; Vessell, R.K. [David K. Davies & Associates, Kingwood, TX (United States); Doublet, L.E. [Texas A& M Univ., College Station, TX (United States)] [and others

1997-08-01

An integrated geological/petrophysical and reservoir engineering study was performed for a large, mature waterflood project (>250 wells, {approximately}80% water cut) at the North Robertson (Clear Fork) Unit, Gaines County, Texas. The primary goal of the study was to develop an integrated reservoir description for {open_quotes}targeted{close_quotes} (economic) 10-acre (4-hectare) infill drilling and future recovery operations in a low permeability, carbonate (dolomite) reservoir. Integration of the results from geological/petrophysical studies and reservoir performance analyses provide a rapid and effective method for developing a comprehensive reservoir description. This reservoir description can be used for reservoir flow simulation, performance prediction, infill targeting, waterflood management, and for optimizing well developments (patterns, completions, and stimulations). The following analyses were performed as part of this study: (1) Geological/petrophysical analyses: (core and well log data) - {open_quotes}Rock typing{close_quotes} based on qualitative and quantitative visualization of pore-scale features. Reservoir layering based on {open_quotes}rock typing {close_quotes} and hydraulic flow units. Development of a {open_quotes}core-log{close_quotes} model to estimate permeability using porosity and other properties derived from well logs. The core-log model is based on {open_quotes}rock types.{close_quotes} (2) Engineering analyses: (production and injection history, well tests) Material balance decline type curve analyses to estimate total reservoir volume, formation flow characteristics (flow capacity, skin factor, and fracture half-length), and indications of well/boundary interference. Estimated ultimate recovery analyses to yield movable oil (or injectable water) volumes, as well as indications of well and boundary interference.

Combined stable isotope trajectories for water-rock interaction

International Nuclear Information System (INIS)

Blattner, P.; Department of Scientific and Industrial Research, Lower Hutt

1981-01-01

The 'mixed' model of water-rock interaction (1980 Workshop) is explained in detail. Based on the magnitude of the oxygen isotope shifts of their recharge water, different geothermal systems can be placed in an evolutionary series, from incipient (large shift of water) to mature (small shift of water). Isotopes of different chemical elements may be combined, to yield a stringent test of whether or not a given change in rock composition may be ascribed to interaction with water (L-shaped trajectories). For the acidic eruptives of the Taupo Volcanic Zone, available strontium and oxygen isotope data practically rule out an origin by partial melting of greywacke basement

Biomarkers, carbon isotopic composition and source rock potentials of Awgu coals, middle Benue trough, Nigeria

Science.gov (United States)

Adedosu, Taofik A.; Sonibare, Oluwadayo O.; Tuo, Jincai; Ekundayo, Olusegun

2012-05-01

Coal and carbonaceous shale samples were collected from two boreholes (BH 94 and BH 120) in Awgu formation of Middle Benue Trough, Nigeria. Source rock potentials of the samples were studied using biomarkers and carbon isotopic composition. Biomarkers in the aliphatic fractions in the samples were studied using Gas Chromatography-Mass Spectrometry (GC-MS). The Carbon isotope analysis of individual n-alkanes in the aliphatic fraction was performed using Gas Chromatography-Combustion-Isotope Ratio Mass Spectrometer (GC-IRMS). The abundance of hopanes, homohopanes (C31-C35), and C29 steranes in the samples indicate terrestrial plant, phytoplankton and cyanobacteria contributions to the organic matter that formed the coal. High (Pr/Ph) ratio (3.04-11.07) and isotopic distribution of individual alkanes showed that the samples consisted of mixed terrestrial/marine organic matter deposited under oxic condition in lacustrine-fluvial/deltaic depositional environment. The maturity parameters derived from biomarker distributions showed that the samples are in the main phase of oil window.

Fluid-Rock Characterization and Interactions in NMR Well Logging

Energy Technology Data Exchange (ETDEWEB)

George J. Hirasaki; Kishore K. Mohanty

2005-09-05

The objective of this report is to characterize the fluid properties and fluid-rock interactions that are needed for formation evaluation by NMR well logging. The advances made in the understanding of NMR fluid properties are summarized in a chapter written for an AAPG book on NMR well logging. This includes live oils, viscous oils, natural gas mixtures, and the relation between relaxation time and diffusivity. Oil based drilling fluids can have an adverse effect on NMR well logging if it alters the wettability of the formation. The effect of various surfactants on wettability and surface relaxivity are evaluated for silica sand. The relation between the relaxation time and diffusivity distinguishes the response of brine, oil, and gas in a NMR well log. A new NMR pulse sequence in the presence of a field gradient and a new inversion technique enables the T{sub 2} and diffusivity distributions to be displayed as a two-dimensional map. The objectives of pore morphology and rock characterization are to identify vug connectivity by using X-ray CT scan, and to improve NMR permeability correlation. Improved estimation of permeability from NMR response is possible by using estimated tortuosity as a parameter to interpolate between two existing permeability models.

Effect of diagenesis on pore pressures in fine-grained rocks in the Egersund Basin, Central North Sea

OpenAIRE

Kalani, Mohsen; Zadeh, Mohammad Koochak; Jahren, Jens; Mondol, Nazmul Haque; Faleide, Jan Inge

2015-01-01

- Pore pressure in fine-grained rocks is important with respect to drilling problems such as kicks, blowouts, borehole instability, stuck pipe and lost circulation. In this study, a succession of overpressured, fine-grained, sedimentary rocks located in the Egersund Basin, Central North Sea, was analysed with respect to mineralogical composition, source-rock maturation and log-derived petrophysical properties to highlight the effect of diagenetic processes on the pore pressure. Pe...

Oil troubles waters

International Nuclear Information System (INIS)

Bravo, E.

1998-01-01

The sea provides a vast array of natural resources for thousands of local communities in the tropics. But the presence of the oil industry has significant social and environmental impacts, both from accidents and from routine activities like seismic exploration, drilling and the generation of polluting wastes. When accidents occur, sessile life (species attached to surface such as rocks or the seabed) is the first to be affected; its mortality increases as oil accumulates, although certain organisms, like gastropods, tolerate it better

Geochemical investigation of petroleum source rocks by using Rock- Eval data in the Agha-Jari oilfield

Directory of Open Access Journals (Sweden)

Behzad khani

2015-01-01

Full Text Available In this study, 40 drilling cutting of the Pabdeh, Gurpi, kazhdumi and Gadvan Formations from the Agha-Jari Oilfield were analyzed by using Rock-Eval pyrolysis. In order to recognizing sedimentary environmental conditions of studied Formations, they are divided to 4 zones which A (Kazhdumi Formation#187 and C (Kazhdumi Formation#140 zones show reduction conditions by presence of sea organic materials and B (Gadvan Formation #140 and D(Gadvan Formation#187 zones show oxidation conditions by presence of continental organic materials to basin. Based on the Rock-Eval pyrolysis data, the Pabeh, Gurpi, Kazhdumi and Gadvan Formations have variable hydrocarbon generative potential. HI vs. OI plot revealed that the kerogen type in this Formations is a mixed of types II & III. The intensity of matrix effect in the Pabdeh, Gurpi, Kazhdumi and Gadvan Formations was compared by using S2 vs. TOC plot and calculating its regression equation. The results show that the significant amount of S2 adsorption by matrix was happened in the Pabdeh (4.98-6.96 mg HC/gr rock in wells 113 and 121 and Gurpi Formations ‌(4.33 mg HC/gr rock in well 113 which is due to their low thermal maturity‌(Tmax

Geochemical characterization of Neogene sediments from onshore West Baram Delta Province, Sarawak: paleoenvironment, source input and thermal maturity

Science.gov (United States)

Togunwa, Olayinka S.; Abdullah, Wan H.

2017-08-01

The Neogene strata of the onshore West Baram Province of NW Borneo contain organic rich rock formations particularly within the Sarawak basin. This basin is a proven prolific oil and gas province, thus has been a subject of great interest to characterise the nature of the organic source input and depositional environment conditions as well as thermal maturation. This study is performed on outcrop samples of Lambir, Miri and Tukau formations, which are of stratigraphic equivalence to the petroleum bearing cycles of the offshore West Baram delta province in Sarawak. The investigated mudstone samples are organic rich with a total organic carbon (TOC) content of more than 1.0 wt.%. The integration of elemental and molecular analyses indicates that there is no significant variation in the source input between these formations. The investigated biomarkers parameters achieved from acyclic isoprenoids, terpanes and steranes biomarkers of a saturated hydrocarbon biomarkers revealed that these sediments contain high contribution of land plants with minor marine organic matter input that was deposited and preserved under relatively oxic to suboxic conditions. This is further supported by low total sulphur (TS), high TOC/TN ratios, source and redox sensitive trace elements (V, Ni, Cr, Co and Mo) concentrations and their ratios, which suggest terrigenous source input deposited under oxic to suboxic conditions. Based on the analysed biomarker thermal maturity indicators, it may be deduced that the studied sediments are yet to enter the maturity stage for hydrocarbon generation, which is also supported by measured vitrinite reflectance values of 0.39-0.48% Ro.

Geochemical characterization of Neogene sediments from onshore West Baram Delta Province, Sarawak: paleoenvironment, source input and thermal maturity

Directory of Open Access Journals (Sweden)

Togunwa Olayinka S.

2017-08-01

Full Text Available The Neogene strata of the onshore West Baram Province of NW Borneo contain organic rich rock formations particularly within the Sarawak basin. This basin is a proven prolific oil and gas province, thus has been a subject of great interest to characterise the nature of the organic source input and depositional environment conditions as well as thermal maturation. This study is performed on outcrop samples of Lambir, Miri and Tukau formations, which are of stratigraphic equivalence to the petroleum bearing cycles of the offshore West Baram delta province in Sarawak. The investigated mudstone samples are organic rich with a total organic carbon (TOC content of more than 1.0 wt.%. The integration of elemental and molecular analyses indicates that there is no significant variation in the source input between these formations. The investigated biomarkers parameters achieved from acyclic isoprenoids, terpanes and steranes biomarkers of a saturated hydrocarbon biomarkers revealed that these sediments contain high contribution of land plants with minor marine organic matter input that was deposited and preserved under relatively oxic to suboxic conditions. This is further supported by low total sulphur (TS, high TOC/TN ratios, source and redox sensitive trace elements (V, Ni, Cr, Co and Mo concentrations and their ratios, which suggest terrigenous source input deposited under oxic to suboxic conditions. Based on the analysed biomarker thermal maturity indicators, it may be deduced that the studied sediments are yet to enter the maturity stage for hydrocarbon generation, which is also supported by measured vitrinite reflectance values of 0.39-0.48% Ro.

Investigations on THM effects in buffer, EDZ and argillaceous host rock. Final report

Energy Technology Data Exchange (ETDEWEB)

Jobmann, M.; Breustedt, M.; Li, S.; Polster, M.; Schirmer, S.

2013-11-15

especially valid for the most reactive rock components, which are the fine grained clay matrix and the organic components. A high amount of organic compounds is characteristic for clay formations. If the thermal maturation is advanced, an additional artificial heating over longer periods of time may have the effect that the limit where oil generation starts is exceeded. It is still to be clarified whether the heat input from the waste canisters is so high that this limit is exceeded and that oil in an amount worth extracting is generated. Depending on the pressure and temperature conditions, a mineral transformation or the formation of new minerals may occur, which would change the chemical and mineralogical conditions. Artificial heating could accelerate transformation processes and change the retardation properties of the host rock. Currently, there is no information available about the potential changes of the host rock properties due to the specific heat input of a repository in a clay formation in Germany. One important task to be performed with regard to the German safety requirements is the demonstration of the integrity of the geotechnical barriers and of the geological barrier. The only way to demonstrate the long-term integrity of the geological barrier is to carry out predictive calculations. These kinds of calculations must have a sound basis of rock-specific constitutive laws together with a well calibrated parameter set that represent the real physical host rock behaviour. To identify suitable constitutive laws and corresponding parameters, insitu experiments are being performed in the Mt. Terri and Meuse/Haute-Marne URLs in Switzerland and France. These experiments are well equipped with sensing systems that allow a comparison of measured and simulated results for rock parameter identification and corresponding model calibration.

Parameters influencing the yield and composition of the essential oil from Cretan Vitex agnus-castus fruits.

Science.gov (United States)

Sørensen, J M; Katsiotis, S T

2000-04-01

Mature and immature fruits of a Cretan Vitex agnus-castus L. population were chosen to investigate different parameters such as comminution, maturity, distillation period and extraction method influencing the essential oil yield and composition. The effect of the comminution and the maturity of the plant material showed highly significant differences in yield and composition of the essential oils obtained, as well as the distillation duration from one to five hours and the method applied (hydrodistillation and simultaneous distillation extraction). The variation of 36 essential oil components due to the parameters applied was studied. The results showed that many different essential oil qualities can be obtained from the same plant material according to the parameters employed in its extraction. Entire fruits hydrodistilled for one hour yielded an oil much richer in monoterpene hydrocarbons and oxygenated compounds whereas the best combination to obtain an oil rich in less volatile compounds is by SDE of comminuted fruits for five hours. For mature fruits the main components varied as follows due to the parameters studied: sabinene 16.4-44.1%, 1,8-cineole 8.4-15.2%, beta-caryophyllene 2.1-5.0%, and trans-beta-farnesene 5.0-11.7%.

Applying Bioaugmentation to Treat DNAPL Sources in Fractured Rock

Science.gov (United States)

2017-03-27

Figure 1. This ESTCP demonstration was focused in the vicinity of Building 8595, adjacent to the location of a reported surface release of PCE ( Earth ...electron donor source, such as vegetable oil, is typically used in passive approaches. When treating a DNAPL source area in fractured rock, there are... vegetable oil) are used. Hydrogen The generation of hydrogen can be used to verify fermentation of electron donor. Metals (Fe, Mn, As) Increase

Economic viability of mature fields: a successful experience; Viabilidade economica de campos maduros: uma experiencia bem sucedida

Energy Technology Data Exchange (ETDEWEB)

Pacheco, Almi C.; Carvalho, Antonio Marcio D.; Santana, Francisco Pablo P.; Neto, Francisco A.S.; Souza, Thiago T. [Universidade Federal da Bahia (UFBA), Salvador, BA (Brazil)

2008-07-01

After the end of the PETROBRAS monopoly in Brazil, the country started a new exploratory stage. Until the beginning of the pre-salt researches, the discovery of new oil mature fields was almost impossible. To take back the incentive to new researches about on-shore basins, without affect the focus on the off-shore basins, the Agencia Nacional de Petroleo, Gas Natural e Biocombustiveis (ANP) has been making efforts to increase the segment of oil medium and small size producers, who are called independent producers. To guarantee the good results, ANP has created auctions of mature and original fields of oil. The objective is to attract small and medium companies, so they can contribute to new technology of land exploration. The auctions have brought strength to the independent producers. The aim of this article is to show the case of Quiambina field, which belongs to the Campo-Escola Project, created by ANP in partnership with Universidade Federal da Bahia (UFBA) to revitalize the fields considered as matures, returned by PETROBRAS at the end of its monopoly era. To prove the economic viability of these mature shields, it will be used real values, get in the first four years of production. (author)

Hydrogenizing oils, asphalts, etc

Energy Technology Data Exchange (ETDEWEB)

1925-03-14

The hydrogenation of carbonaceous solids in presence of combined sulfur, e.g., sulfides as described in the parent specification is applied to the treatment of rock oils, shale oils, resins, ozokerite, asphalt, and the like, or fractions, residues, or acid sludge or other conversion products thereof, alone or mixed. Preferably the hydrogen or other reducing gas is in excess and under pressure, and is either circuited or led through a series of treatment vessels, hydrogen being added for that used. In an example, residues from American crude oil are passed continuously with hydrogen at 200 atmospheres and 450 to 500/sup 0/C over pressed precipitated cobalt sulfide, the issuing gases being cooled to condense the light oil produced.

Dynamic international oil markets

International Nuclear Information System (INIS)

van der Linde, C.

1992-01-01

Dynamic International Oil Market Developments and Structure 1860-1990 discusses the logic of changing market structures of the international oil industry. The market structures have, in the course of time, oscillated between competition and oligopoly, as the oil market expanded, matured, stagnated, and expanded again. This book provides a dynamic interpretation of the intensifying struggle among producer, and consumer governments, and oil companies, over the distribution of economic rents and profits. In particular, it shows the shifting fortunes of the governments and companies as they try to control the recurring capacity constraints between the upstream and downstream sectors, generated by the instability of the oil market. The first part of the book examines market conditions and developments between 1860 and 1990; the second part analyzes market structures after 1945

Rock solidification method

International Nuclear Information System (INIS)

Nakaya, Iwao; Murakami, Tadashi; Miyake, Takafumi; Funakoshi, Toshio; Inagaki, Yuzo; Hashimoto, Yasuhide.

1985-01-01

Purpose: To convert radioactive wastes into the final state for storage (artificial rocks) in a short period of time. Method: Radioactive burnable wastes such as spent papers, cloths and oils and activated carbons are burnt into ashes in a burning furnace, while radioactive liquid wastes such as liquid wastes of boric acid, exhausted cleaning water and decontaminating liquid wastes are powderized in a drying furnace or calcining furnace. These powders are joined with silicates as such as white clay, silica and glass powder and a liquid alkali such as NaOH or Ca(OH) 2 and transferred to a solidifying vessel. Then, the vessel is set to a hydrothermal reactor, heated and pressurized, then taken out about 20 min after and tightly sealed. In this way, radioactive wastes are converted through the hydrothermal reactions into aqueous rock stable for a long period of time to obtain solidification products insoluble to water and with an extremely low leaching rate. (Ikeda, J.)

Biological marker distribution in coexisting kerogen, bitumen and asphaltenes in Monterey Formation diatomite, California

Science.gov (United States)

Tannenbaum, E.; Ruth, E.; Huizinga, B. J.; Kaplan, I. R.

1986-01-01

Organic-rich (18.2%) Monterey Formation diatomite from California was studied. The organic matter consist of 94% bitumen and 6% kerogen. Biological markers from the bitumen and from pyrolysates of the coexisting asphaltenes and kerogen were analyzed in order to elucidate the relationship between the various fractions of the organic matter. While 17 alpha(H), 18 alpha(H), 21 alpha(H)-28,30-bisnorhopane was present in the bitumen and in the pryolysate of the asphaltenes, it was not detected in the pyrolysates of the kerogen. A C40-isoprenoid with "head to head" linkage, however, was present in pyrolysates of both kerogen and asphaltenes, but not in the bitumen from the diatomite. The maturation level of the bitumen, based on the extent of isomerization of steranes and hopanes, was that of a mature oil, whereas the pyrolysate from the kerogen showed a considerably lower maturation level. These relationships indicate that the bitumen may not be indigenous to the diatomite and that it is a mature oil that migrated into the rock. We consider the possibility, however, that some of the 28,30-bisnorhopane-rich Monterey Formation oils have not been generated through thermal degradation of kerogen, but have been expelled from the source rock at an early stage of diagenesis.

Study on thermal history and oil-generated environment from well CC1

International Nuclear Information System (INIS)

Xia Yuliang; Zhu Jiechen; Zheng Maogong

1997-01-01

U-Pb isotope geochronological study of core samples implies that the sedimentary strata are derived from North-China ancient land and the age of the hidden granite derived from the remelted Archean rocks with lower crust signature is 99 Ma. Fluid inclusion investigation indicates that the Ordovician carbonate rocks are rich in organic matters and should be a better set of oil-generated rocks and reservoir. Based on fission track analysis of apatites from different depths and the paleo-geothermal variation, the authors suggest that there be at least three oil-generated stages. The range of annealing belt of apatite tracks and the paleo-geothermal gradient in this well are 1700-3900 m (roughly corresponding to oil-generated belt) and 3.1 degree C/100 m respectively after Tertiary sedimentation

Bridging the Gap between Chemical Flooding and Independent Oil Producers

Energy Technology Data Exchange (ETDEWEB)

Stan McCool; Tony Walton; Paul Whillhite; Mark Ballard; Miguel Rondon; Kaixu Song; Zhijun Liu; Shahab Ahmed; Peter Senior

2012-03-31

Ten Kanas oil reservoirs/leases were studied through geological and engineering analysis to assess the potential performance of chemical flooding to recover oil. Reservoirs/leases that have been efficiently waterflooded have the highest performance potential for chemical flooding. Laboratory work to identify efficient chemical systems and to test the oil recovery performance of the systems was the major effort of the project. Efficient chemical systems were identified for crude oils from nine of the reservoirs/leases. Oil recovery performance of the identified chemical systems in Berea sandstone rocks showed 90+ % recoveries of waterflood residual oil for seven crude oils. Oil recoveries increased with the amount of chemical injected. Recoveries were less in Indiana limestone cores. One formulation recovered 80% of the tertiary oil in the limestone rock. Geological studies for nine of the oil reservoirs are presented. Pleasant Prairie, Trembley, Vinland and Stewart Oilfields in Kansas were the most favorable of the studied reservoirs for a pilot chemical flood from geological considerations. Computer simulations of the performance of a laboratory coreflood were used to predict a field application of chemical flooding for the Trembley Oilfield. Estimates of field applications indicated chemical flooding is an economically viable technology for oil recovery.

RESEARCH OIL RECOVERY MECHANISMS IN HEAVY OIL RESERVOIRS

Energy Technology Data Exchange (ETDEWEB)

Anthony R. Kovscek; William E. Brigham

1999-06-01

The United States continues to rely heavily on petroleum fossil fuels as a primary energy source, while domestic reserves dwindle. However, so-called heavy oil (10 to 20{sup o}API) remains an underutilized resource of tremendous potential. Heavy oils are much more viscous than conventional oils. As a result, they are difficult to produce with conventional recovery methods such as pressure depletion and water injection. Thermal recovery is especially important for this class of reservoirs because adding heat, usually via steam injection, generally reduces oil viscosity dramatically. This improves displacement efficiency. The research described here was directed toward improved understanding of thermal and heavy-oil production mechanisms and is categorized into: (1) flow and rock properties; (2) in-situ combustion; (3) additives to improve mobility control; (4) reservoir definition; and (5) support services. The scope of activities extended over a three-year period. Significant work was accomplished in the area of flow properties of steam, water, and oil in consolidated and unconsolidated porous media, transport in fractured porous media, foam generation and flow in homogeneous and heterogeneous porous media, the effects of displacement pattern geometry and mobility ratio on oil recovery, and analytical representation of water influx. Significant results are described.

Natural Offshore Oil Seepage and Related Tarball Accumulation on the California Coastline - Santa Barbara Channel and the Southern Santa Maria Basin: Source Identification and Inventory

Science.gov (United States)

Lorenson, T.D.; Hostettler, Frances D.; Rosenbauer, Robert J.; Peters, Kenneth E.; Dougherty, Jennifer A.; Kvenvolden, Keith A.; Gutmacher, Christina E.; Wong, Florence L.; Normark, William R.

2009-01-01

seafloor was mapped by sidescan sonar, and numerous lines of high -resolution seismic surveys were conducted over areas of interest. Biomarker and stable carbon isotope ratios were used to infer the age, lithology, organic matter input, and depositional environment of the source rocks for 388 samples of produced crude oil, seep oil, and tarballs mainly from coastal California. These samples were used to construct a chemometric fingerprint (multivariate statistics) decision tree to classify 288 additional samples, including tarballs of unknown origin collected from Monterey and San Mateo County beaches after a storm in early 2007. A subset of 9 of 23 active offshore platform oils and one inactive platform oil representing a few oil reservoirs from the western Santa Barbara Channel were used in this analysis, and thus this model is not comprehensive and the findings are not conclusive. The platform oils included in this study are from west to east: Irene, Hildago, Harvest, Hermosa, Heritage, Harmony, Hondo, Holly, Platform A, and Hilda (now removed). The results identify three 'tribes' of 13C-rich oil samples inferred to originate from thermally mature equivalents of the clayey-siliceous, carbonaceous marl, and lower calcareous-siliceous members of the Monterey Formation. Tribe 1 contains four oil families having geochemical traits of clay-rich marine shale source rock deposited under suboxic conditions with substantial higher-plant input. Tribe 2 contains four oil families with intermediate traits, except for abundant 28,30-bisnorhopane, indicating suboxic to anoxic marine marl source rock with hemipelagic input. Tribe 3 contains five oil families with traits of distal marine carbonate source rock deposited under anoxic conditions with pelagic but little or no higher-plant input. Tribes 1 and 2 occur mainly south of Point Conception in paleogeographic settings where deep burial of the Monterey Formation source rock favored generation from all thre

Oil prospection using the tectonic plate model

Science.gov (United States)

Pointu, Agnès

2015-04-01

Tectonic plate models are an intellectual setting to understand why oil deposits are so uncommon and unequally distributed and how models can be used in actual oil and gas prospection. In this case, we use the example of the Ghawar deposit (Saudi Arabia), one of the largest producing well in the world. In the first step, physical properties of rocks composing the oil accumulation are studied by laboratory experiments. Students estimate the porosity of limestone and clay by comparing their mass before and after water impregnation. Results are compared to microscopic observations. Thus, students come to the conclusion that oil accumulations are characterized by superposition of rocks with very different properties: a rich organic source rock (clays of the Hanifa formation), a porous reservoir rock to store the petroleum in (limestones of the Arab formation) and above an impermeable rock with very low porosity (evaporites of the Tithonien). In previous lessons, students have seen that organic matter is usually mineralized by bacteria and that this preservation requires particular conditions. The aim is to explain why biomass production has been so important during the deposit of the clays of the Hanifa formation. Tectonic plate models make it possible to estimate the location of the Arabian Peninsula during Jurassic times (age of Hanifa formation). In order to understand why the paleo-location of the Arabian Peninsula is important to preserve organic matter, students have different documents showing: - That primary production of biomass by phytoplankton is favored by climatic conditions, - That the position of continents determinate the ocean currents and the positions of upwelling zones and zones where organic matter will be able to be preserved, - That north of the peninsula there was a passive margin during Jurassic times. An actual seismic line is studied in order to highlight that this extensive area allowed thick sedimentary deposits to accumulate and that fast

Petroleum geological features and exploration prospect of deep marine carbonate rocks in China onshore: A further discussion

Directory of Open Access Journals (Sweden)

Zhao Wenzhi

2014-10-01

Full Text Available Deep marine carbonate rocks have become one of the key targets of onshore oil and gas exploration and development for reserves replacement in China. Further geological researches of such rocks may practically facilitate the sustainable, steady and smooth development of the petroleum industry in the country. Therefore, through a deep investigation into the fundamental geological conditions of deep marine carbonate reservoirs, we found higher-than-expected resource potential therein, which may uncover large oil or gas fields. The findings were reflected in four aspects. Firstly, there are two kinds of hydrocarbon kitchens which were respectively formed by conventional source rocks and liquid hydrocarbons cracking that were detained in source rocks, and both of them can provide large-scale hydrocarbons. Secondly, as controlled by the bedding and interstratal karstification, as well as the burial and hydrothermal dolomitization, effective carbonate reservoirs may be extensively developed in the deep and ultra-deep strata. Thirdly, under the coupling action of progressive burial and annealing heating, some marine source rocks could form hydrocarbon accumulations spanning important tectonic phases, and large quantity of liquid hydrocarbons could be kept in late stage, contributing to rich oil and gas in such deep marine strata. Fourthly, large-scale uplifts were formed by the stacking of multi-episodic tectonism and oil and gas could be accumulated in three modes (i.e., stratoid large-area reservoir-forming mode of karst reservoirs in the slope area of uplift, back-flow type large-area reservoir-forming mode of buried hill weathered crust karst reservoirs, and wide-range reservoir-forming mode of reef-shoal reservoirs; groups of stratigraphic and lithologic traps were widely developed in the areas of periclinal structures of paleohighs and continental margins. In conclusion, deep marine carbonate strata in China onshore contain the conditions for

Investigating the effects of rock porosity and permeability on the performance of nitrogen injection into a southern Iranian oil reservoirs through neural network

Science.gov (United States)

Gheshmi, M. S.; Fatahiyan, S. M.; Khanesary, N. T.; Sia, C. W.; Momeni, M. S.

2018-03-01

In this work, a comprehensive model for Nitrogen injection into an oil reservoir (southern Iranian oil fields) was developed and used to investigate the effects of rock porosity and permeability on the oil production rate and the reservoir pressure decline. The model was simulated and developed by using ECLIPSE300 software, which involved two scenarios as porosity change and permeability changes in the horizontal direction. We found that the maximum pressure loss occurs at a porosity value of 0.07, which later on, goes to pressure buildup due to reservoir saturation with the gas. Also we found that minimum pressure loss is encountered at porosity 0.46. Increases in both pressure and permeability in the horizontal direction result in corresponding increase in the production rate, and the pressure drop speeds up at the beginning of production as it increases. However, afterwards, this pressure drop results in an increase in pressure because of reservoir saturation. Besides, we determined the regression values, R, for the correlation between pressure and total production, as well as for the correlation between permeability and the total production, using neural network discipline.

Effect of Rock Properties on ROP Modeling Using Statistical and Intelligent Methods: A Case Study of an Oil Well in Southwest of Iran

Science.gov (United States)

Bezminabadi, Sina Norouzi; Ramezanzadeh, Ahmad; Esmaeil Jalali, Seyed-Mohammad; Tokhmechi, Behzad; Roustaei, Abbas

2017-03-01

Rate of penetration (ROP) is one of the key indicators of drilling operation performance. The estimation of ROP in drilling engineering is very important in terms of more accurate assessment of drilling time which affects operation costs. Hence, estimation of a ROP model using operational and environmental parameters is crucial. For this purpose, firstly physical and mechanical properties of rock were derived from well logs. Correlation between the pair data were determined to find influential parameters on ROP. A new ROP model has been developed in one of the Azadegan oil field wells in southwest of Iran. The model has been simulated using Multiple Nonlinear Regression (MNR) and Artificial Neural Network (ANN). By adding the rock properties, the estimation of the models were precisely improved. The results of simulation using MNR and ANN methods showed correlation coefficients of 0.62 and 0.87, respectively. It was concluded that the performance of ANN model in ROP prediction is fairly better than MNR method.

Deceased Slabs Drive Oil

Science.gov (United States)

Stein, H. J.; Hannah, J. L.

2017-12-01

The application of Re-Os isotope geochemistry to dating single oils is a nascent field [1,2]. Challenges include dissection of oils into asphaltene-maltene (ASPH-MALT) components in a way that preserves meaningful chronologic and source information. Significantly, oil-water mixing rapidly transfers Os to the oil, while Re exchange is sluggish [3]. The Os initial ratio of the oil is shifted in the direction of Os carried in the aqueous fluid, whereas the Re-Os isotopic age is preserved. We show that this phenomenon is operative in natural systems. Further, we show that deserpentinization of old oceanic slabs [4], may be linked to expulsion of Os-enriched waters into overlying sedimentary sections - a process that may be of fundamental importance for oil generation. This conclusion does not diminish the role of traditional organic-rich shales as source rocks for the hydrocarbon, but shows that external fluids are essential to petroleum generation. Moreover, the external fluids may be an important driver for expulsion and migration of oils. We have taken apart several petroleum systems from source rock, to residual oil, to tar mat development, to in situ live oil, through to produced oil. In many cases, a fluid with low 187Os/188Os - unlike that of normal basinal brines - provides a critical component to the oil-water mixture. Funding - CHRONOS project supported by Norwegian petroleum industry (Eni-Norge, Lundin, Aker BP) Acknowledgement - Christine Fichler [4], who first queried us on old slabs and oil, and stimulated ideas. [1] Georgiev, S.V., Stein, H.J., Hannah, J.L., Galimberti, R., Nali, M., Yang, G., and Zimmerman, A. (2016) Re-Os dating of maltenes and asphaltenes within single samples of crude oil: Geochim. Cosmochim. Acta 179: 53-75. [doi.org/10.1016/j.gca.2016.01.016] [2] DiMarzio, J., Georgiev, S.V., Stein, H.J., and Hannah, J.L. (in press) Residency of rhenium and osmium in a heavy crude oil: Geochim. Cosmochim. Acta. [3] Hurtig, N.C., Georgiev, S

Numerical simulation of rock cutting using 2D AUTODYN

International Nuclear Information System (INIS)

Woldemichael, D E; Rani, A M Abdul; Lemma, T A; Altaf, K

2015-01-01

In a drilling process for oil and gas exploration, understanding of the interaction between the cutting tool and the rock is important for optimization of the drilling process using polycrystalline diamond compact (PDC) cutters. In this study the finite element method in ANSYS AUTODYN-2D is used to simulate the dynamics of cutter rock interaction, rock failure, and fragmentation. A two-dimensional single PDC cutter and rock model were used to simulate the orthogonal cutting process and to investigate the effect of different parameters such as depth of cut, and back rake angle on two types of rocks (sandstone and limestone). In the simulation, the cutting tool was dragged against stationary rock at predetermined linear velocity and the depth of cut (1,2, and 3 mm) and the back rake angles(-10°, 0°, and +10°) were varied. The simulation result shows that the +10° back rake angle results in higher rate of penetration (ROP). Increasing depth of cut leads to higher ROP at the cost of higher cutting force. (paper)

An Alternative to Conventional Rock Fragmentation Methods Using SCDA: A Review

Directory of Open Access Journals (Sweden)

Radhika Vidanage De Silva

2016-11-01

Full Text Available Global energy and material consumption are expected to rise in exponential proportions during the next few decades, generating huge demands for deep earth energy (oil/gas recovery and mineral processing. Under such circumstances, the continuation of existing methods in rock fragmentation in such applications is questionable due to the proven adverse environmental impacts associated with them. In this regard; the possibility of using more environmentally friendly options as Soundless Chemical Demolition Agents (SCDAs play a vital role in replacing harmful conventional rock fragmentation techniques for gas; oil and mineral recovery. This study reviews up to date research on soundless cracking demolition agent (SCDA application on rock fracturing including its limitations and strengths, possible applications in the petroleum industry and the possibility of using existing rock fragmentation models for SCDA-based rock fragmentation; also known as fracking. Though the expansive properties of SCDAs are currently used in some demolition works, the poor usage guidelines available reflect the insufficient research carried out on its material’s behavior. SCDA is a cementitious powdery substance with quicklime (CaO as its primary ingredient that expands upon contact with water; which results in a huge expansive pressure if this CaO hydration reaction occurs in a confined condition. So, the mechanism can be used for rock fragmentation by injecting the SCDA into boreholes of a rock mass; where the resulting expansive pressure is sufficient to create an effective fracture network in the confined rock mass around the borehole. This expansive pressure development, however, dependent on many factors, where formation water content creates a negative influence on this due to required greater degree of hydration under greater water contents and temperature creates a positive influence by accelerating the reaction. Having a precise understanding of the fracture

Research on Formation Mechanisms of Hot Dry Rock Resources in China

Science.gov (United States)

Wang, G.; Xi, Y.

2017-12-01

As an important geothermal resource, hot dry rock(HDR) reserves have been studied in many countries. HDR resources in China have huge capacity and have become one of the most important resources for the potential replacement of fossil fuels. However, HDR resources are difficult to develop and utilise. Technologies for use with HDR, such as high-temperature drilling, reservoir characterisation, reservoir fracturing, microseismic monitoring and high-temperature power stations, originate from the field of oil and drilling. Addressing how to take advantage of these developed technologies is a key factor in the development of HDR reserves. Based on the thermal crustal structure in China, HDR resources can be divided into four types: high radioactive heat production, sedimentary basin, modern volcano and the inner-plate active tectonic belt. The prospective regions of HDR resources are located in South Tibet, West Yunnan, the southeast coast of China, Bohai Rim, Songliao Basin and Guanzhong Basin. The related essential technologies are relatively mature, and the prospect of HDR power generation is promising. Therefore, analysing the formation mechanisms of HDR resources and promoting the transformation of technological achievements, large-scale development and the utilisation of HDR resources can be achieved in China.

The effect of flocculant on the geotechnical properties of mature fine tailings : An experimental study

NARCIS (Netherlands)

Yao, Y.; Van Tol, A.F.; Van Paassen, L.A.

2012-01-01

When oil sands tailings are deposited in a tailing pond, they settle and segregate to create a layer of stagnant water on top that is reused in oil extraction and a dense mixture of clay, silt and water on the bottom which is referred to as mature fine tailings (MFT). Dewatering of MFT is a problem

X-ray microtomography application in pore space reservoir rock

Energy Technology Data Exchange (ETDEWEB)

Oliveira, M.F.S.; Lima, I. [Nuclear Instrumentation Laboratory, COPPE/UFRJ, P.O. Box 68509, 21.941-972, Rio de Janeiro (Brazil); Borghi, L. [Geology Department, Geosciences Institute, Federal University of Rio de Janeiro, Brazil. (Brazil); Lopes, R.T., E-mail: ricardo@lin.ufrj.br [Nuclear Instrumentation Laboratory, COPPE/UFRJ, P.O. Box 68509, 21.941-972, Rio de Janeiro (Brazil)

2012-07-15

Characterization of porosity in carbonate rocks is important in the oil and gas industry since a major hydrocarbons field is formed by this lithology and they have a complex media porous. In this context, this research presents a study of the pore space in limestones rocks by x-ray microtomography. Total porosity, type of porosity and pore size distribution were evaluated from 3D high resolution images. Results show that carbonate rocks has a complex pore space system with different pores types at the same facies. - Highlights: Black-Right-Pointing-Pointer This study is about porosity parameter in carbonate rocks by 3D X-Ray Microtomography. Black-Right-Pointing-Pointer This study has become useful as data input for modeling reservoir characterization. Black-Right-Pointing-Pointer This technique was able to provide pores, grains and mineralogical differences among the samples.

Application of Multivariate Statistical Analysis to Biomarkers in Se-Turkey Crude Oils

Science.gov (United States)

Gürgey, K.; Canbolat, S.

2017-11-01

Twenty-four crude oil samples were collected from the 24 oil fields distributed in different districts of SE-Turkey. API and Sulphur content (%), Stable Carbon Isotope, Gas Chromatography (GC), and Gas Chromatography-Mass Spectrometry (GC-MS) data were used to construct a geochemical data matrix. The aim of this study is to examine the genetic grouping or correlations in the crude oil samples, hence the number of source rocks present in the SE-Turkey. To achieve these aims, two of the multivariate statistical analysis techniques (Principle Component Analysis [PCA] and Cluster Analysis were applied to data matrix of 24 samples and 8 source specific biomarker variables/parameters. The results showed that there are 3 genetically different oil groups: Batman-Nusaybin Oils, Adıyaman-Kozluk Oils and Diyarbakir Oils, in addition to a one mixed group. These groupings imply that at least, three different source rocks are present in South-Eastern (SE) Turkey. Grouping of the crude oil samples appears to be consistent with the geographic locations of the oils fields, subsurface stratigraphy as well as geology of the area.

APPLICATION OF MULTIVARIATE STATISTICAL ANALYSIS TO BIOMARKERS IN SE-TURKEY CRUDE OILS

Directory of Open Access Journals (Sweden)

K. Gürgey

2017-11-01

Full Text Available Twenty-four crude oil samples were collected from the 24 oil fields distributed in different districts of SE-Turkey. API and Sulphur content (%, Stable Carbon Isotope, Gas Chromatography (GC, and Gas Chromatography-Mass Spectrometry (GC-MS data were used to construct a geochemical data matrix. The aim of this study is to examine the genetic grouping or correlations in the crude oil samples, hence the number of source rocks present in the SE-Turkey. To achieve these aims, two of the multivariate statistical analysis techniques (Principle Component Analysis [PCA] and Cluster Analysis were applied to data matrix of 24 samples and 8 source specific biomarker variables/parameters. The results showed that there are 3 genetically different oil groups: Batman-Nusaybin Oils, Adıyaman-Kozluk Oils and Diyarbakir Oils, in addition to a one mixed group. These groupings imply that at least, three different source rocks are present in South-Eastern (SE Turkey. Grouping of the crude oil samples appears to be consistent with the geographic locations of the oils fields, subsurface stratigraphy as well as geology of the area.

Review of oil families and their petroleum systems of the Williston Basin

Science.gov (United States)

Lillis, Paul G.

2013-01-01

The petroleum system concept was first applied in 1974 (Dow/Williams) to identify three oil systems in the Williston Basin, and recent studies have expanded the number to at least nine. This paper reviews the petroleum geochemistry, oil-oil, and oil-source correlations of the oil systems of the Williston Basin, providing a new perspective and some new findings. Petroleum systems with a known source (documented oil-source correlation) include the Red River (Ordovician), Winnipegosis (Devonian), Bakken (Devonian-Mississippian), Madison (Mississippian), and Tyler (Pennsylvanian) systems. Petroleum systems with an identified source rock but no documented oil-source correlation are considered hypothetical and include the Winnipeg (Ordovician), Duperow (Devonian), and Birdbear (Devonian). The Deadwood (Cambrian-Ordovician) petroleum system is speculative because a good oil-prone source rock has not been identified. The stratigraphic distribution of the oil families from each system is generally limited to the same formation from which they were sourced due to efficient seals and a paucity of vertical migration pathways, but some notable exceptions do occur.

Geochemical evaluation of Pabdeh Formation in Nosrat field, southeast Persian Gulf using Rock- Eval VI pyrolysis

Directory of Open Access Journals (Sweden)

mohammad sadeghi

2015-02-01

Full Text Available The present study was performed on 59 drillhole cuttings from Pabdeh Formation in Nosrat oil field using Rock- Eval VI pryrolysis. Geochemical analysis indicated that Pabdeh Formation possesses poor to good hydrocarbon potential. Plotting S1 against TOC suggests that samples were not affected by polluting substances such as crude oil and lubricants while drilling operation. Jones organic fancies diagram shows B-BC area indicating that Pabdeh Formation was deposited in marine anoxic to oxic environments. HI vesus Tmax shows that most samples initially have had type II kerogen and now reflecting a mixture of type II to III kerogen (capable of generating oil that have already entered oil generation window. In addition, S1+S2 versus TOC plot also suggests that Pabdeh Formation can be considered as a capable hydrocarbon generating source rock in the study area.

A giant oil seep at a salt-induced escarpment of the São Paulo Plateau, Espírito Santo Basin, off Brazil: Host rock characteristics and geochemistry

Science.gov (United States)

Freire, Antonio Fernando Menezes; Iemini, Juliana Andrade; Viana, Adriano Roessler; Magnavita, Luciano Portugal; Dehler, Nolan Maia; Kowsmann, Renato Oscar; Miller, Dennis James; Bezerra, Sabrina Helena Diniz Gilaberte; Zerfass, Geise de Santana dos Anjos; Shimabukuro, Seirin; Nóbrega, Marcos, II

2017-12-01

An international research cruise named Iatá-Piuna took place on the São Paulo Plateau on May 2013 in the Campos and Espírito Santo basins, off Brazil. The cruise was carried ou on board the research vessel (R/V) Yokosuka that hosts the human operated vehicle (HOV) SHINKAI 6500. It aimed at finding chemosynthetic communities, composed of organisms capable of generating their own vital energy by metabolizing organic and inorganic compounds related to seeps. Identification of these organisms could provide information for understanding the origin of life, since they may resemble primitive organisms that existed in the initial stages of life on Earth. During Leg 2 (May 10-24, 2013), however, dives on the northern part of the São Paulo Plateau at the Espírito Santo Basin led to the discovery of a giant oil seep. The seep, ca. 3 nautical miles (ca. 5.6 km) in length is located along an outcrop of Eocene rocks on a salt-induced escarpment of the plateau and at a water depth of ca. 2700 m. The 200 m relief of the seafloor suggests that the seep takes place along an active fault system driven by salt diapirism. The oil was analyzed and identified as a severely biodegraded marine oil, generated by carbonate rocks within a minibasin located to the east of the escarpment. This represents valuable exploratory information because it proves that an active petroleum system is present in the context of minibasins associated with salt diapirism in the area.

Radiation protection and management of NORM residues in the oil and gas industry

International Nuclear Information System (INIS)

Haridasan, P.P.; )

2014-01-01

The radionuclides in oil and gas streams belong to the decay chains of 238 U and 232 Th originate from the reservoir rock that contains oil, gas and formation water. Formation water contains significant concentrations of isotopes of radium dissolved from the reservoir rock. The parent isotopes of uranium and thorium are not mobilized from the rock and hence the radium isotopes appear in the water co-produced with the oil and gas. When the ions of Group II elements are present in the produced water, drops in pressure and temperature can lead to precipitation of sulphate and carbonate scales on the inner walls of production tubulars, well heads, valves, pumps, separators, water treatment vessels, gas treatment and oil storage tanks. The mixed stream of oil, gas and water carries the radon gas generated in the reservoir rock and in the production stream it preferentially follows the dry export gases. Consequently the equipment from gas treatment and transport facilities may accumulate a thin film of 210 Pb in the inner surfaces of gas lines. The radionuclide concentrations in produced water, hard scale and sludge will be presented. Indication on typical quantities of wastes generated and best practices followed in the industry in managing such wastes will be outlined. Information on external gamma exposure and potential internal exposure as well as global emerging issues will be discussed

Evolution characteristic of gypsum-salt rocks of the upper member of Oligocene Lower Ganchaigou Fm in the Shizigou area, western Qaidam Basin

Directory of Open Access Journals (Sweden)

Dinghong Yi

2017-09-01

Full Text Available Over years of oil and gas exploration in the Qaidam Basin, reservoirs have been discovered in many layers. In the Shizigou area, western Qaidam Basin, the upper member of Oligocene Lower Ganchaigou Fm is an important target for oil and gas exploration, and gypsum-salt rocks are the high-quality caprocks for the preservation of oil and gas reservoirs in this area. For predicting oil and gas exploration direction and target in the western Qaidam Basin and providing guidance for its oil and gas exploration deployment, its depositional characteristics and environment of gypsum-salt rocks in this area were investigated based on the core observation, thin section identification, and analysis of grain size, sensitivity parameter ratios (Sr/Cu, Fe/Mn, (Fe + Al/(Ca + Mg, V/(V + Ni and Pr/Ph, pyrite content and inclusions. The following characteristics are identified. First, gypsum-salt rocks are mainly distributed in the depocenter of the lake basin and their thickness decreases towards the margin of the basin. They are laterally transformed into carbonate rocks or terrigenous clastic rocks. They are areally distributed in the shape of irregular ellipse. Second, gypsum-salt rocks are vertically developed mainly in the middle and upper parts of the upper member of Lower Ganchaigou Fm and they are interbedded with carbonate rocks or terrigenous clastic rocks. Their single layer thickness changes greatly, and there are many layers with good continuity. Third, Sand Group III to Group I in the upper member of Lower Ganchaigou Fm (inter-salt are of reductive water environment of semi-deep to deep lake facies due to their sedimentation in an arid and hot climate. It is concluded that gypsum-salt rocks of the upper member of Lower Ganchaigou Fm are distributed widely with great accumulative thickness in this area; and that they are originated from deep lake water by virtue of evaporation, concentration and crystallization in an arid and hot climate instead

Rock melting technology and geothermal drilling

Science.gov (United States)

Rowley, J. C.

1974-01-01

National awareness of the potential future shortages in energy resources has heightened interest in exploration and utilization of a variety of geothermal energy (GTE) reservoirs. The status of conventional drilling of GTE wells is reviewed briefly and problem areas which lead to higher drilling costs are identified and R and D directions toward solution are suggested. In the immediate future, an expanded program of drilling in GTE formations can benefit from improvements in drilling equipment and technology normally associated with oil or gas wells. Over a longer time period, the new rock-melting drill bits being developed as a part of the Los Alamos Scientific Laboratory's Subterrene Program offer new solutions to a number of problems which frequently hamper GTE drilling, including the most basic problem - high temperature. Two of the most favorable characteristics of rock-melting penetrators are their ability to operate effectively in hot rock and produce glass linings around the hole as an integral part of the drilling process. The technical advantages to be gained by use of rock-melting penetrators are discussed in relation to the basic needs for GTE wells.

Genetic control of soybean seed oil: II. QTL and genes that increase oil concentration without decreasing protein or with increased seed yield.

Science.gov (United States)

Eskandari, Mehrzad; Cober, Elroy R; Rajcan, Istvan

2013-06-01

Soybean [Glycine max (L.) Merrill] seed oil is the primary global source of edible oil and a major renewable and sustainable feedstock for biodiesel production. Therefore, increasing the relative oil concentration in soybean is desirable; however, that goal is complex due to the quantitative nature of the oil concentration trait and possible effects on major agronomic traits such as seed yield or protein concentration. The objectives of the present study were to study the relationship between seed oil concentration and important agronomic and seed quality traits, including seed yield, 100-seed weight, protein concentration, plant height, and days to maturity, and to identify oil quantitative trait loci (QTL) that are co-localized with the traits evaluated. A population of 203 F4:6 recombinant inbred lines, derived from a cross between moderately high oil soybean genotypes OAC Wallace and OAC Glencoe, was developed and grown across multiple environments in Ontario, Canada, in 2009 and 2010. Among the 11 QTL associated with seed oil concentration in the population, which were detected using either single-factor ANOVA or multiple QTL mapping methods, the number of QTL that were co-localized with other important traits QTL were six for protein concentration, four for seed yield, two for 100-seed weight, one for days to maturity, and one for plant height. The oil-beneficial allele of the QTL tagged by marker Sat_020 was positively associated with seed protein concentration. The oil favorable alleles of markers Satt001 and GmDGAT2B were positively correlated with seed yield. In addition, significant two-way epistatic interactions, where one of the interacting markers was solely associated with seed oil concentration, were identified for the selected traits in this study. The number of significant epistatic interactions was seven for yield, four for days to maturity, two for 100-seed weight, one for protein concentration, and one for plant height. The identified molecular

Fundamentals of Reservoir Surface Energy as Related to Surface Properties, Wettability, Capillary Action, and Oil Recovery from Fractured Reservoirs by Spontaneous Imbibition

Energy Technology Data Exchange (ETDEWEB)

Norman Morrow; Herbert Fischer; Yu Li; Geoffrey Mason; Douglas Ruth; Siddhartha Seth; Zhengxin Tong; Evren Unsal; Siluni Wickramathilaka; Shaochang Wo; Peigui Yin

2008-06-30

The objective of this project is to increase oil recovery from fractured reservoirs through improved fundamental understanding of the process of spontaneous imbibition by which oil is displaced from the rock matrix into the fractures. Spontaneous imbibition is fundamentally dependent on the reservoir surface free energy but this has never been investigated for rocks. In this project, the surface free energy of rocks will be determined by using liquids that can be solidified within the rock pore space at selected saturations. Thin sections of the rock then provide a two-dimensional view of the rock minerals and the occupant phases. Saturations and oil/rock, water/rock, and oil/water surface areas will be determined by advanced petrographic analysis and the surface free energy which drives spontaneous imbibition will be determined as a function of increase in wetting phase saturation. The inherent loss in surface free energy resulting from capillary instabilities at the microscopic (pore level) scale will be distinguished from the decrease in surface free energy that drives spontaneous imbibition. A mathematical network/numerical model will be developed and tested against experimental results of recovery versus time over broad variation of key factors such as rock properties, fluid phase viscosities, sample size, shape and boundary conditions. Two fundamentally important, but not previously considered, parameters of spontaneous imbibition, the capillary pressure acting to oppose production of oil at the outflow face and the pressure in the non-wetting phase at the no-flow boundary versus time, will also be measured and modeled. Simulation and network models will also be tested against special case solutions provided by analytic models. In the second stage of the project, application of the fundamental concepts developed in the first stage of the project will be demonstrated. The fundamental ideas, measurements, and analytic/numerical modeling will be applied to mixed

FUNDAMENTALS OF RESERVOIR SURFACE ENERGY AS RELATED TO SURFACE PROPERTIES, WETTABILITY, CAPILLARY ACTION, AND OIL RECOVERY FROM FRACTURED RESERVOIRS BY SPONTANEOUS IMBIBITION

Energy Technology Data Exchange (ETDEWEB)

Norman R. Morrow

2004-05-01

The objective of this project is to increase oil recovery from fractured reservoirs through improved fundamental understanding of the process of spontaneous imbibition by which oil is displaced from the rock matrix into the fractures. Spontaneous imbibition is fundamentally dependent on the reservoir surface free energy but this has never been investigated for rocks. In this project, the surface free energy of rocks will be determined by using liquids that can be solidified within the rock pore space at selected saturations. Thin sections of the rock then provide a two-dimensional view of the rock minerals and the occupant phases. Saturations and oil/rock, water/rock, and oil/water surface areas will be determined by advanced petrographic analysis and the surface free energy which drives spontaneous imbibition will be determined as a function of increase in wetting phase saturation. The inherent loss in surface free energy resulting from capillary instabilities at the microscopic (pore level) scale will be distinguished from the decrease in surface free energy that drives spontaneous imbibition. A mathematical network/numerical model will be developed and tested against experimental results of recovery versus time over broad variation of key factors such as rock properties, fluid phase viscosities, sample size, shape and boundary conditions. Two fundamentally important, but not previously considered, parameters of spontaneous imbibition, the capillary pressure acting to oppose production of oil at the outflow face and the pressure in the nonwetting phase at the no-flow boundary versus time, will also be measured and modeled. Simulation and network models will also be tested against special case solutions provided by analytic models. In the second stage of the project, application of the fundamental concepts developed in the first stage of the project will be demonstrated. The fundamental ideas, measurements, and analytic/numerical modeling will be applied to mixed

FUNDAMENTALS OF RESERVOIR SURFACE ENERGY AS RELATED TO SURFACE PROPERTIES, WETTABILITY, CAPILLARY ACTION, AND OIL RECOVERY FROM FRACTURED RESERVOIRS BY SPONTANEOUS IMBIBITION

Energy Technology Data Exchange (ETDEWEB)

Norman R. Morrow

2004-07-01

The objective of this project is to increase oil recovery from fractured reservoirs through improved fundamental understanding of the process of spontaneous imbibition by which oil is displaced from the rock matrix into the fractures. Spontaneous imbibition is fundamentally dependent on the reservoir surface free energy but this has never been investigated for rocks. In this project, the surface free energy of rocks will be determined by using liquids that can be solidified within the rock pore space at selected saturations. Thin sections of the rock then provide a two-dimensional view of the rock minerals and the occupant phases. Saturations and oil/rock, water/rock, and oil/water surface areas will be determined by advanced petrographic analysis and the surface free energy which drives spontaneous imbibition will be determined as a function of increase in wetting phase saturation. The inherent loss in surface free energy resulting from capillary instabilities at the microscopic (pore level) scale will be distinguished from the decrease in surface free energy that drives spontaneous imbibition. A mathematical network/numerical model will be developed and tested against experimental results of recovery versus time over broad variation of key factors such as rock properties, fluid phase viscosities, sample size, shape and boundary conditions. Two fundamentally important, but not previously considered, parameters of spontaneous imbibition, the capillary pressure acting to oppose production of oil at the outflow face and the pressure in the nonwetting phase at the no-flow boundary versus time, will also be measured and modeled. Simulation and network models will also be tested against special case solutions provided by analytic models. In the second stage of the project, application of the fundamental concepts developed in the first stage of the project will be demonstrated. The fundamental ideas, measurements, and analytic/numerical modeling will be applied to mixed

Study of Kerogen Maturity using Transmission Fourier Transform Infrared Spectroscopy (FTIR)

Science.gov (United States)

Dang, S. T.

2014-12-01

Maturity of kerogen in shale governs the productivity and generation hydrocarbon type. There are generally two accepted methods to measure kerogen maturity; one is the measurement of vitrinite reflectance, %Ro, and another is the measurement of Tmax through pyrolysis. However, each of these techniques has its own limits; vitrinite reflectance measurement cannot be applied to marine shale and pre-Silurian shales, which lack plant materials. Furthermore, %Ro, requires the isolation and identification of vitrinite macerals and statistical measurements of at least 50 macerals. Tmax measurement is questionable for mature and post-mature samples. In addition, there are questions involving the effects of solvents on Tmax determinations. Fourier Transmission Infrared Spectroscopy, FTIR, can be applied for both qualitative and quantitative assessment on organics maturity in shale. The technique does not require separating organic matter or identifying macerals. A CH2/CH3 index, RCH, calculated from FTIR spectra is more objective than other measurements. The index increases with maturity (both natural maturation and synthetic maturation through hydrous and dry pyrolysis). The new maturity index RCH can be calibrated to vitrinite reflectance which allows the definition of the following values for levels of maturity: 1) immature—RCH > 1.6±0.2; 2) oil window-- 1.6±0.2 1.3±0.3; 3) wet gas window--1.3±0.3 1.13±0.05; and 4) dry gas window RCH < 1.13±0.05.

Induction of embryogenic callus and plantlet regeneration from young leaves of high yielding mature oil palm

Directory of Open Access Journals (Sweden)

Yeedum, I.

2004-09-01

Full Text Available Callus induction and plantlet regeneration from young leaves of high-yielding mature oil palm were carried out using 10-year and 20-year-old trees from Thepa Research Station, Faculty of Natural Resources,Prince of Songkla University, Hat Yai, and Trang Agricultural College, respectively. Culture media used in this experiment were Murashige and Skoog (1962 and Oil Palm supplemented with various concentrations of α-naphthaleneacetic acid (NAA or 2,4- dichlorophenoxy acetic acid (2,4-D or dicamba (Di and antioxidants.Young leaves from 6th to 11st frond were excised, sterilized, cut into 5x5 mm pieces and cultured in the dark at 26±4ºC or 28±0.5ºC for 3 months. The results revealed that MS medium with 200 mg/l ascorbic acid (As and 1 mg/l Di (MS-AsDi gave the highest callus induction percentage (7.93 after culture for 3 months at 28±0.5ºC. Leaf segments from 6th - 8th frond yielded callus forming percentage at 10% (averaged from 1, 2.5 and 5 mg/l Di containing MS medium. Ascorbic acid as an antioxidant at concentration of 200 mg/l supplemented in MS medium in the presence of 2.5 mg/l Di produced the highest callus induction percentage (11.2 and number of nodules (7.06. A high percentage of embryogenic callus formation (66.67 was obtained when the calli were transferred to the same medium component supplemented with 0.5 mg/l Di and 1,000 mg/l casein hydrolysate (CH (MS-AsDiCH. Haustorial-staged embryos were observed to be isolated as an individual embryo and germinated on MS medium without plant growth regulator (MS-free. Development of root could be classified into two distinct types, fibrous and tap root.

Geologic assessment of undiscovered oil and gas resources—Lower Cretaceous Albian to Upper Cretaceous Cenomanian carbonate rocks of the Fredericksburg and Washita Groups, United States Gulf of Mexico Coastal Plain and State Waters

Science.gov (United States)

Swanson, Sharon M.; Enomoto, Catherine B.; Dennen, Kristin O.; Valentine, Brett J.; Cahan, Steven M.

2017-02-10

In 2010, the U.S. Geological Survey (USGS) assessed Lower Cretaceous Albian to Upper Cretaceous Cenomanian carbonate rocks of the Fredericksburg and Washita Groups and their equivalent units for technically recoverable, undiscovered hydrocarbon resources underlying onshore lands and State Waters of the Gulf Coast region of the United States. This assessment was based on a geologic model that incorporates the Upper Jurassic-Cretaceous-Tertiary Composite Total Petroleum System (TPS) of the Gulf of Mexico basin; the TPS was defined previously by the USGS assessment team in the assessment of undiscovered hydrocarbon resources in Tertiary strata of the Gulf Coast region in 2007. One conventional assessment unit (AU), which extends from south Texas to the Florida panhandle, was defined: the Fredericksburg-Buda Carbonate Platform-Reef Gas and Oil AU. The assessed stratigraphic interval includes the Edwards Limestone of the Fredericksburg Group and the Georgetown and Buda Limestones of the Washita Group. The following factors were evaluated to define the AU and estimate oil and gas resources: potential source rocks, hydrocarbon migration, reservoir porosity and permeability, traps and seals, structural features, paleoenvironments (back-reef lagoon, reef, and fore-reef environments), and the potential for water washing of hydrocarbons near outcrop areas.In Texas and Louisiana, the downdip boundary of the AU was defined as a line that extends 10 miles downdip of the Lower Cretaceous shelf margin to include potential reef-talus hydrocarbon reservoirs. In Mississippi, Alabama, and the panhandle area of Florida, where the Lower Cretaceous shelf margin extends offshore, the downdip boundary was defined by the offshore boundary of State Waters. Updip boundaries of the AU were drawn based on the updip extent of carbonate rocks within the assessed interval, the presence of basin-margin fault zones, and the presence of producing wells. Other factors evaluated were the middle

The Role of Geochemistry and Basin Modelling in the Exploration of Mature province

International Nuclear Information System (INIS)

Katz, A.J.

2002-01-01

Petroleum geochemistry and basin modelling has been an important tool in the reduction of risks in poorly explored basins. Historically the role of geochemistry is usually reduced once production is established and often in mature province is nonexistent. However, attempts to add reserves in mature provinces require an expansion of exploration programs based on new play concepts. Consequently, there is a clear role for geochemistry and basin modelling as this revitalization occurs.These new basin modelling and geochemical programs are aimed at answering three questions: . Can the petroleum system be extended? . Is a change in hydrocarbon character to be expected? . How much hydrocarbon potential remains?Unlike frontier exploration a significant sample base is normally available that can be used to more effectively constrain interpretations. Such programs have clearly aided exploration in the Niger Delta. For example, the collection of an extensive piston core dataset in conjunction with a basin modelling program provided strong support for the Niger Delta's petroleum system extending into deep water areas. While the geochemical character of the oils established the presence of multiple effective generative systems, each of which has different source characteristics and often-different ages. This information constraints model construction and hydrocarbon volume estimates. Oil data also established the importance of phase segregation. The presence of fractionated oils and maturation modelling results provides evidence for deeper hydrocarbon potential within the geographic limits of established hydrocarbon pays

Enzymes for Enhanced Oil Recovery (EOR)

Energy Technology Data Exchange (ETDEWEB)

Nasiri, Hamidreza

2011-04-15

Primary oil recovery by reservoir pressure depletion and secondary oil recovery by waterflooding usually result in poor displacement efficiency. As a consequence there is always some trapped oil remaining in oil reservoirs. Oil entrapment is a result of complex interactions between viscous, gravity and capillary forces. Improving recovery from hydrocarbon fields typically involves altering the relative importance of the viscous and capillary forces. The potential of many EOR methods depends on their influence on fluid/rock interactions related to wettability and fluid/fluid interactions reflected in IFT. If the method has the potential to change the interactions favorably, it may be considered for further investigation, i.e. core flooding experiment, pilot and reservoir implementation. Enzyme-proteins can be introduced as an enhanced oil recovery method to improve waterflood performance by affecting interactions at the oil-water-rock interfaces. An important part of this thesis was to investigate how selected enzymes may influence wettability and capillary forces in a crude oil-brine-rock system, and thus possibly contribute to enhanced oil recovery. To investigate further by which mechanisms selected enzyme-proteins may contribute to enhance oil recovery, groups of enzymes with different properties and catalytic functions, known to be interfacially active, were chosen to cover a wide range of possible effects. These groups include (1) Greenzyme (GZ) which is a commercial EOR enzyme and consists of enzymes and stabilizers (surfactants), (2) The Zonase group consists of two types of pure enzyme, Zonase1 and Zonase2 which are protease enzymes and whose catalytic functions are to hydrolyze (breakdown) peptide bonds, (3) The Novozyme (NZ) group consists of three types of pure enzyme, NZ2, NZ3 and NZ6 which are esterase enzymes and whose catalytic functions are to hydrolyze ester bonds, and (4) Alpha-Lactalbumin ( -La) which is an important whey protein. The effect of

SEQUENCE STRATIGRAPHIC ANALYSIS AND FACIES ARCHITECTURE OF THE CRETACEOUS MANCOS SHALE ON AND NEAR THE JICARILLA APACHE INDIAN RESERVATION, NEW MEXICO-THEIR RELATION TO SITES OF OIL ACCUMULATION

International Nuclear Information System (INIS)

Jennie Ridgley

2000-01-01

the oil (except for the Tocito Sandstone) from the lower Mancos. In the central and southern part of the Reservation, large areas, currently not productive or not tested, have the potential to contain oil in the El Vado simply based on the trend of the facies and structure. There has been little oil or gas production from the overlying regressive-transgressive wedge of rock and much of this interval is untested. Thus, large areas of the Reservation could contain hydrocarbon resources in these strata. Most of the Reservation lies within the oil generation window based on new Rock-Eval data from the Mancos Shale just south of the southern part of the Reservation. If these observations are valid then oil could have been generated locally and would only have needed to migrate short distances in to sandy reservoirs and fractures. This does not rule out long distance migration of oil from the deeper, more thermally mature part of the basin to the north. However, low porosity and permeability characterize sandier rocks in the Mancos, with the exception of Tocito-like sandstones. These factors could retard long distance oil migration through the sediment package, except through fracture or fault conduits. Thus, it is suggested that future oil and gas explorations in the Mancos treat the accumulations and reservoirs as unconventional and consider whether the source and reservoir are in closer proximity than has previously been assumed

Geology and assessment of undiscovered oil and gas resources of the Hope Basin Province, 2008

Science.gov (United States)

Bird, Kenneth J.; Houseknecht, David W.; Pitman, Janet K.; Moore, Thomas E.; Gautier, Donald L.

2018-01-04

The Hope Basin, an independent petroleum province that lies mostly offshore in the southern Chukchi Sea north of the Chukotka and Seward Peninsulas and south of Wrangel Island, the Herald Arch, and the Lisburne Peninsula, is the largest in a series of postorogenic (successor) basins in the East Siberian-Chukchi Sea region and the only one with exploratory-well control and extensive seismic coverage.In spite of the seismic coverage and well data, the petroleum potential of the Hope Basin Province is poorly known. The adequacy of hydrocarbon charge, in combination with uncertainties in source-rock potential and maturation, was the greatest risk in this assessment. A single assessment unit was defined and assessed, resulting in mean estimates of undiscovered, technically recoverable resources that include ~3 million barrels of oil and 650 billion cubic feet of nonassociated gas.

Modelling of underground geomechanical characteristics for electrophysical conversion of oil shale

International Nuclear Information System (INIS)

Bukharkin, A A; Koryashov, I A; Martemyanov, S M; Ivanov, A A

2015-01-01

Oil shale energy extraction is an urgent issue for modern science and technique. With the help of electrical discharge phenomena it is possible to create a new efficient technology for underground conversion of oil shale to shale gas and oil. This method is based on Joule heat in the rock volume. During the laboratory experiments the problem has arisen, when the significant part of a shale fragment is being heated, but the further heating is impossible due to specimen cracking. It leads to disruption in current flow and heat exchange. Evidently, in the underground conditions these failure processes will not proceed. Cement, clay and glass fiber/epoxy resin armature have been used for modelling of geomechanical underground conditions. Experiments have shown that the use of a reinforcing jacket makes it possible to convert a full rock fragment. Also, a thermal field extends radially from the centre of a tree-type structure, and it has an elliptic cross section shape. It is explained by the oil shale anisotropy connected with a rock laminar structure. Therefore, heat propagation is faster along the layers than across ones. (paper)

Oil shale, shale oil, shale gas and non-conventional hydrocarbons

Directory of Open Access Journals (Sweden)

Clerici A.

2015-01-01

Full Text Available In recent years there has been a world “revolution” in the field of unconventional hydrocarbon reserves, which goes by the name of “shale gas”, gas contained inside clay sediments micropores. Shale gas finds particular development in the United States, which are now independent of imports and see a price reduction to less than one third of that in Europe. With the high oil prices, in addition to the non-conventional gas also “oil shales” (fine-grained sedimentary rocks that contain a large amount of organic material to be used both to be directly burned or to extract liquid fuels which go under the name of shale oil, extra heavy oils and bitumen are becoming an industrial reality. Both unconventional gas and oil reserves far exceed in the world the conventional oil and gas reserves, subverting the theory of fossil fuels scarcity. Values and location of these new fossil reserves in different countries and their production by comparison with conventional resources are presented. In view of the clear advantages of unconventional fossil resources, the potential environmental risks associated with their extraction and processing are also highlighted.

Acute and chronic toxicity study of the water accommodated fraction (WAF), chemically enhanced WAF (CEWAF) of crude oil and dispersant in the rock pool copepod Tigriopus japonicus.

Science.gov (United States)

Lee, Kyun-Woo; Shim, Won Joon; Yim, Un Hyuk; Kang, Jung-Hoon

2013-08-01

We determined the toxicity of the water accommodated hydrocarbon fraction (WAF), two chemically enhanced WAFs (CEWAFs; CEWAF-C, Crude oil+Corexit 9500 and CEWAF-H, Crude oil+Hiclean) of crude oil and two dispersants (Corexit 9500 and Hiclean) to the rock pool copepod Tigriopus japonicus. In the acute toxicity test, Corexit 9500 was the most toxic of all the chemicals studied. The nauplius stage of T. japonicus was more susceptible to the toxic chemicals studied than the adult female. The toxicity data using the nauplius stage was then considered as baseline to determine the spiking concentration of chemicals for chronic toxicity tests on the copepod. As the endpoints in the chronic toxicity test, survival, sex ratio, developmental time and fecundity of the copepod were used. All chemicals used in this study resulted in increased toxicity in the F1 generation. The lowest-observed-adverse-effect (LOAE) concentrations of WAF, CEWAF-H, CEWAF-C, Hiclean and Corexit 9500 were observed to be 50%, 10%, 0.1%, 1% and 1%, respectively. The results in present study imply that copepods in marine may be negatively influenced by spilled oil and dispersant. Copyright © 2013 Elsevier Ltd. All rights reserved.

Quantification of oil recovery efficiency, CO 2 storage potential, and fluid-rock interactions by CWI in heterogeneous sandstone oil reservoirs

DEFF Research Database (Denmark)

Seyyedi, Mojtaba; Sohrabi, Mehran; Sisson, Adam

2017-01-01

Significant interest exists in improving recovery from oil reservoirs while addressing concerns about increasing CO2 concentrations in the atmosphere. The combination of Enhanced Oil Recovery (EOR) and safe geologic storage of CO2 in oil reservoirs is appealing and can be achieved by carbonated (CO...... for oil recovery and CO2 storage potential on heterogeneous cores. Since not all the oil reservoirs are homogenous, understanding the potential of CWI as an integrated EOR and CO2 storage scenario in heterogeneous oil reservoirs is essential....

Potency of Agroindustrial Wastewaters to Increase the Dissolution of Phosphate Rock Fertilizers

Directory of Open Access Journals (Sweden)

Ainin Niswati

2014-06-01

Full Text Available The used of agroindustrial wastewaters are not maximum yet in Lampung Province, althought it can be used as an acid solvent because of its acidic properties. This study was aimed to explore the most potential agroindustrial wastewaters in dissolving phosphate rock through acidulation in the laboratory scale. The experiment was arranged in a factorial. The first factor was origined of phosphate rock (Sukabumi, west Java and Selagailingga, central Lampung and the second factor was solvent types (agroindustrial wastewaters which were pineapple, tapioca, tofu industry, and palm oil as well as conventional acid solvents which were HCl, H2SO4, and CH3COOH. The incubation processes were 0, 1, 2, and 3 months. The results showed that agroindustrial wastewaters that have the highest potency to solubize phosphate rock was industrial tofu wastewaters and followed by industrial wastewaters of tapioca, palm oil, and pineapple. Both the conventional acid and agroindustrial wastewaters solvent had a big potency to solubilize phosphate rock, however, its highest soluble P-value did not match with the ISO criteria for phosphate fertilizers Quality I (SNI because it did not reach the solubility of 80% of its total P2O5, but it has been qualified as a fertilizer both the quality phosphate A, B, and C (SNI.

Prospects of Microbial Enhanced Oil Recovery  in Danish chalk rocks

DEFF Research Database (Denmark)

Rudyk, Svetlana Nikolayevna; Jørgensen, Leif Wagner; Bah Awasi, Ismail

  Microbial Enhanced Oil Recovery (MEOR) uses bacteria, producing gas (CO2), polymers or surfactants to help recover residual oil after the water injection depletes its possibilities. Two strains of Clostridia tyrobutiricum were investigated as possible candidates for MEOR  implementation in Danish...

Modelling of oil spill frequency, leak sources and contamination probability in the Caspian Sea using multi-temporal SAR images 2006–2010 and stochastic modelling

Directory of Open Access Journals (Sweden)

Emil Bayramov

2016-05-01

Full Text Available The main goal of this research was to detect oil spills, to determine the oil spill frequencies and to approximate oil leak sources around the Oil Rocks Settlement, the Chilov and Pirallahi Islands in the Caspian Sea using 136 multi-temporal ENVISAT Advanced Synthetic Aperture Radar Wide Swath Medium Resolution images acquired during 2006–2010. The following oil spill frequencies were observed around the Oil Rocks Settlement, the Chilov and Pirallahi Islands: 2–10 (3471.04 sq km, 11–20 (971.66 sq km, 21–50 (692.44 sq km, 51–128 (191.38 sq km. The most critical oil leak sources with the frequency range of 41–128 were observed at the Oil Rocks Settlement. The exponential regression analysis between wind speeds and oil slick areas detected from 136 multi-temporal ENVISAT images revealed the regression coefficient equal to 63%. The regression model showed that larger oil spill areas were observed with decreasing wind speeds. The spatiotemporal patterns of currents in the Caspian Sea explained the multi-directional spatial distribution of oil spills around Oil Rocks Settlement, the Chilov and Pirallahi Islands. The linear regression analysis between detected oil spill frequencies and predicted oil contamination probability by the stochastic model showed the positive trend with the regression coefficient of 30%.

Chitin: 'Forgotten' Source of Nitrogen: From Modern Chitin to Thermally Mature Kerogen: Lessons from Nitrogen Isotope Ratios

Science.gov (United States)

Schimmelmann, A.; Wintsch, R.P.; Lewan, M.D.; DeNiro, M.J.

1998-01-01

Chitinous biomass represents a major pool of organic nitrogen in living biota and is likely to have contributed some of the fossil organic nitrogen in kerogen. We review the nitrogen isotope biogeochemistry of chitin and present preliminary results suggesting interaction between kerogen and ammonium during thermal maturation. Modern arthropod chitin may shift its nitrogen isotope ratio by a few per mil depending on the chemical method of chitin preparation, mostly because N-containing non-amino-sugar components in chemically complex chitin cannot be removed quantitatively. Acid hydrolysis of chemically complex chitin and subsequent ion-chromatographic purification of the "deacetylated chitin-monomer" D-glucosamine (in hydrochloride form) provides a chemically well-defined, pure amino-sugar substrate for reproducible, high-precision determination of ??15N values in chitin. ??15N values of chitin exhibited a variability of about one per mil within an individual's exoskeleton. The nitrogen isotope ratio differed between old and new exoskeletons by up to 4 per mil. A strong dietary influence on the ??15N value of chitin is indicated by the observation of increasing ??15N values of chitin from marine crustaceans with increasing trophic level. Partial biodegradation of exoskeletons does not significantly influence ??15N values of remaining, chemically preserved amino sugar in chitin. Diagenesis and increasing thermal maturity of sedimentary organic matter, including chitin-derived nitrogen-rich moieties, result in humic compounds much different from chitin and may significantly change bulk ??15N values. Hydrous pyrolysis of immature source rocks at 330??C in contact with 15N-enriched NH4Cl, under conditions of artificial oil generation, demonstrates the abiogenic incorporation of inorganic nitrogen into carbon-bound nitrogen in kerogen. Not all organic nitrogen in natural, thermally mature kerogen is therefore necessarily derived from original organic matter, but may

Hyperspectral and Radar Airborne Imagery over Controlled Release of Oil at Sea

Directory of Open Access Journals (Sweden)

Sébastien Angelliaume

2017-08-01

Full Text Available Remote sensing techniques are commonly used by Oil and Gas companies to monitor hydrocarbon on the ocean surface. The interest lies not only in exploration but also in the monitoring of the maritime environment. Occurrence of natural seeps on the sea surface is a key indicator of the presence of mature source rock in the subsurface. These natural seeps, as well as the oil slicks, are commonly detected using radar sensors but the addition of optical imagery can deliver extra information such as thickness and composition of the detected oil, which is critical for both exploration purposes and efficient cleanup operations. Today, state-of-the-art approaches combine multiple data collected by optical and radar sensors embedded on-board different airborne and spaceborne platforms, to ensure wide spatial coverage and high frequency revisit time. Multi-wavelength imaging system may create a breakthrough in remote sensing applications, but it requires adapted processing techniques that need to be developed. To explore performances offered by multi-wavelength radar and optical sensors for oil slick monitoring, remote sensing data have been collected by SETHI (Système Expérimental de Télédection Hyperfréquence Imageur, the airborne system developed by ONERA (the French Aerospace Lab, during an oil spill cleanup exercise carried out in 2015 in the North Sea, Europe. The uniqueness of this dataset lies in its high spatial resolution, low noise level and quasi-simultaneous acquisitions of different part of the EM spectrum. Specific processing techniques have been developed to extract meaningful information associated with oil-covered sea surface. Analysis of this unique and rich dataset demonstrates that remote sensing imagery, collected in both optical and microwave domains, allows estimating slick surface properties such as the age of the emulsion released at sea, the spatial abundance of oil and the relative concentration of hydrocarbons remaining on

Sedimentary petrology of oil well rock cores; Petrologia sedimentaria de nucleos de rocas de pozos petroleros

Energy Technology Data Exchange (ETDEWEB)

Izquierdo M, Georgina; Paredes S, Adriana [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

2001-07-01

At the request of PEMEX Exploration and Production (PEP), in the area of Geology of the Gerencia de Geotermia, the necessary methodology has been integrated to carry out the geologic characterization of cores obtained during the oil well drilling. The integrated studies have been of utility for PEMEX, because they provide detailed information on the processes, conditions of deposition and diagenesis that occur in sedimentary rocks. On the other hand, this geologic information contributes to the update of the geologic model of the field in study. [Spanish] A solicitud de PEMEX Exploracion y Produccion (PEP), en el area de Geologia de la Gerencia de Geotermia, se ha integrado la metodologia necesaria para llevar a cabo la caracterizacion geologica de nucleos obtenidos durante la perforacion de pozos petroleros. Los estudios integrados han sido de utilidad para PEMEX, pues proporcionan informacion detallada sobre los procesos, condiciones de depositacion y diagenesis que ocurren en rocas sedimentarias. Por otro lado, esta informacion geologica contribuye a la actualizacion del modelo geologico del campo en estudio.

Polygenetic Aspect of Unit Theory Oil Generation

Science.gov (United States)

Galant, Yuri

2015-04-01

In the framework of a unified theory Oil Generation one of important moments is the consideration of the distribution of oil in the Earth's Crust. Analysis of the distribution of oil deposits in the Earth's Crust showed that oil distributed throughout the stratigraphic section from ancient to modern sediments and from a depth of 12 kilometers to the Earth's surface. The distribution of oil almost meets all stages of metamorphism of rocks. Correlation of the section of oil distribution to genetic types of ore deposits showed that each genetic type ore deposits has its analogue oil field . So it is possible to classify oil fields on 1) endogenous: the actual magmatic, post-magmatic, contact-metasomatic (skarn), hydrothermal, exhalation, carbonatite, pegmatite, 2) exogenous: weathering, oxidation, sedimentary,3) metamorphogenic: metamorphosed, metamorphic. Model of such distribution of oil deposits can be a process of successive formation of oil deposits of mantle degassing tube. Thus oil is polygenic by way of formation of deposits, but their source is united.

Managing Injected Water Composition To Improve Oil Recovery: A Case Study of North Sea Chalk Reservoirs

DEFF Research Database (Denmark)

Zahid, Adeel; Shapiro, Alexander; Stenby, Erling Halfdan

2012-01-01

of the temperature dependence of the oil recovery indicated that the interaction of the ions contained in brine with the rock cannot be the only determining mechanism of enhanced recovery. We observed no substitution of Ca2+ ions with Mg2+ ions at high temperatures for both rocks. Not only the injection brine......In recent years, many core displacement experiments of oil by seawater performed on chalk rock samples have reported SO42–, Ca2+, and Mg2+ as potential determining ions for improving oil recovery. Most of these studies were carried out with outcrop chalk core plugs. The objective of this study...... is to investigate the potential of the advanced waterflooding process by carrying out experiments with reservoir chalk samples. The study results in a better understanding of the mechanisms involved in increasing the oil recovery with potential determining ions. We carried out waterflooding instead of spontaneous...

A novel molecular index for secondary oil migration distance.

Science.gov (United States)

Zhang, Liuping; Li, Maowen; Wang, Yang; Yin, Qing-Zhu; Zhang, Wenzheng

2013-01-01

Determining oil migration distances from source rocks to reservoirs can greatly help in the search for new petroleum accumulations. Concentrations and ratios of polar organic compounds are known to change due to preferential sorption of these compounds in migrating oils onto immobile mineral surfaces. However, these compounds cannot be directly used as proxies for oil migration distances because of the influence of source variability. Here we show that for each source facies, the ratio of the concentration of a select polar organic compound to its initial concentration at a reference point is independent of source variability and correlates solely with migration distance from source rock to reservoir. Case studies serve to demonstrate that this new index provides a valid solution for determining source-reservoir distance and could lead to many applications in fundamental and applied petroleum geoscience studies.

Real-Time Optimization of a maturing North Sea gas asset with production constraints

NARCIS (Netherlands)

Linden, R.J.P. van der; Busking, T.E.

2013-01-01

As gas and oil fields mature their operation becomes increasingly more complex, due to complex process dynamics, like slugging, gas coning, water breakthrough, salt or hydrate deposition. Moreover these phenomena also lead to production constraints in the upstream facilities. This complexity asks

Evaluation of the level of maturity in project management in a department of a company in the oil and gas sector; Avaliacao do nivel de maturidade em gerenciamento de projetos em um departamento de uma empresa do setor de oleo e gas

Energy Technology Data Exchange (ETDEWEB)

Tavares, Marina Elisabete Espinho [Petroleo Brasileiro S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil)

2012-07-01

This work aims to analyse the results from methodology MMGP-Prado Setorial (2008) applied in a planning and control department from oil and gas segment, and suggest actions to increase its maturity level. (author)

Petroleum systems of the Upper Magdalena Valley, Colombia

Energy Technology Data Exchange (ETDEWEB)

Sarmiento, L.F.; Rangel, A. [Instituto Colombiano del Petroleo, Bucaramanga (Colombia). ECOPETROL

2004-03-01

In the Upper Magdalena Valley, Colombia, four petroleum systems were identified. Two petroleum systems are located in the Girardot sub-basin and the other two in the Neiva sub- basin. Limestones laterally changing to shales of the lower part of the Villeta Gp, deposited during Albian and Turonian marine flooding events, constitutes the main source rocks of the oil families. These rocks contain 1-4% TOC and type II kerogen. The littoral quartz arenites of the Caballos (Albian) and Monserrate (Maastrichtian) Fms. are the main reservoir rocks. Seal rocks are Cretaceous and Paleocene shales. Overburden includes the Cretaceous rocks and the Tertiary molasse deposited simultaneously with development of two opposite verging thrust systems during Cenozoic time. These deformation events were responsible for trap creation. Except for the Villarrica area, where the source rock reached maturity during the Paleocene, generation occurred during Miocene. Two oil families are identified, each in both sub-basins: One derived from a clay-rich source and the second from a carbonate-rich source rock lithofacies of the lower part of Villeta Gp. Geochemical source-rock to oil correlations are demonstrated for the three of the petroleum systems. Up-dip lateral migration distances are relatively short and faults served as vertical migration pathways. A huge amount of oil was probably degraded at surface, as a result of Miocene deformation and erosion. (author)

Origin of oil shale

Energy Technology Data Exchange (ETDEWEB)

Cunningham-Craig, E H

1915-01-01

Kerogen was believed to be formed by the inspissation of petroleum. During this process nitrogen and sulfur compounds were concentrated in the most inspissated or weathered products. At a certain stage, reached gradually, the organic matter became insoluble in carbon-disulfide and ceased to be a bitumen. Oil shale was formed by the power of certain clays or shales to absorb inspissated petroleum, particularly unsaturated hydrocarbons. This adsorption apparently depended on the colloid content of the argillaceous rock. This rock retained these impregnated petroleum residues long after porous sandstones in the vicinity had lost all traces of petroleum by weathering and leaching.

Dual Resonant Frequencies Effects on an Induction-Based Oil Palm Fruit Sensor

Directory of Open Access Journals (Sweden)

Noor Hasmiza Harun

2014-11-01

Full Text Available As the main exporter in the oil palm industry, the need to improve the quality of palm oil has become the main interest among all the palm oil millers in Malaysia. To produce good quality palm oil, it is important for the miller to harvest a good oil palm Fresh Fruit Bunch (FFB. Conventionally, the main reference used by Malaysian harvesters is the manual grading standard published by the Malaysian Palm Oil Board (MPOB. A good oil palm FFB consists of all matured fruitlets, aged between 18 to 21 weeks of antheses (WAA. To expedite the harvesting process, it is crucial to implement an automated detection system for determining the maturity of the oil palm FFB. Various automated detection methods have been proposed by researchers in the field to replace the conventional method. In our preliminary study, a novel oil palm fruit sensor to detect the maturity of oil palm fruit bunch was proposed. The design of the proposed air coil sensor based on the inductive sensor was further investigated mainly in the context of the effect of coil diameter to improve its sensitivity. In this paper, the sensitivity of the inductive sensor was further examined with a dual flat-type shape of air coil. The dual air coils were tested on fifteen samples of fruitlet from two categories, namely ripe and unripe. Samples were tested within 20 Hz to 10 MHz while evaluations on both peaks were done separately before the gap between peaks was analyzed. A comparative analysis was conducted to investigate the improvement in sensitivity of the induction-based oil palm fruit sensor as compared to previous works. Results from the comparative study proved that the inductive sensor using a dual flat-type shape air coil has improved by up to 167%. This provides an indication in the improvement in the coil sensitivity of the palm oil fruit sensor based on the induction concept.

Dual resonant frequencies effects on an induction-based oil palm fruit sensor.

Science.gov (United States)

Harun, Noor Hasmiza; Misron, Norhisam; Mohd Sidek, Roslina; Aris, Ishak; Wakiwaka, Hiroyuki; Tashiro, Kunihisa

2014-11-19

As the main exporter in the oil palm industry, the need to improve the quality of palm oil has become the main interest among all the palm oil millers in Malaysia. To produce good quality palm oil, it is important for the miller to harvest a good oil palm Fresh Fruit Bunch (FFB). Conventionally, the main reference used by Malaysian harvesters is the manual grading standard published by the Malaysian Palm Oil Board (MPOB). A good oil palm FFB consists of all matured fruitlets, aged between 18 to 21 weeks of antheses (WAA). To expedite the harvesting process, it is crucial to implement an automated detection system for determining the maturity of the oil palm FFB. Various automated detection methods have been proposed by researchers in the field to replace the conventional method. In our preliminary study, a novel oil palm fruit sensor to detect the maturity of oil palm fruit bunch was proposed. The design of the proposed air coil sensor based on the inductive sensor was further investigated mainly in the context of the effect of coil diameter to improve its sensitivity. In this paper, the sensitivity of the inductive sensor was further examined with a dual flat-type shape of air coil. The dual air coils were tested on fifteen samples of fruitlet from two categories, namely ripe and unripe. Samples were tested within 20 Hz to 10 MHz while evaluations on both peaks were done separately before the gap between peaks was analyzed. A comparative analysis was conducted to investigate the improvement in sensitivity of the induction-based oil palm fruit sensor as compared to previous works. Results from the comparative study proved that the inductive sensor using a dual flat-type shape air coil has improved by up to 167%. This provides an indication in the improvement in the coil sensitivity of the palm oil fruit sensor based on the induction concept.

Dynamic response of shear induced structure solutions in permeable rock

NARCIS (Netherlands)

Reuvers, N.J.W.; Spain, D.S.W.; Golombok, M.

2009-01-01

Additives for improving the flow uniformity during secondary oil recovery are partially retained in the rock. The flow improval effects continue to be observed even when the chemical solution is succeeded by pure water. Considerable flushing with water is required before the old permeability of the

Shale characterization in mass transport complex as a potential source rock: An example from onshore West Java Basin, Indonesia

Science.gov (United States)

Nugraha, A. M. S.; Widiarti, R.; Kusumah, E. P.

2017-12-01

This study describes a deep-water slump facies shale of the Early Miocene Jatiluhur/Cibulakan Formation to understand its potential as a source rock in an active tectonic region, the onshore West Java. The formation is equivalent with the Gumai Formation, which has been well-known as another prolific source rock besides the Oligocene Talang Akar Formation in North West Java Basin, Indonesia. The equivalent shale formation is expected to have same potential source rock towards the onshore of Central Java. The shale samples were taken onshore, 150 km away from the basin. The shale must be rich of organic matter, have good quality of kerogen, and thermally matured to be categorized as a potential source rock. Investigations from petrography, X-Ray diffractions (XRD), and backscattered electron show heterogeneous mineralogy in the shales. The mineralogy consists of clay minerals, minor quartz, muscovite, calcite, chlorite, clinopyroxene, and other weathered minerals. This composition makes the shale more brittle. Scanning Electron Microscope (SEM) analysis indicate secondary porosities and microstructures. Total Organic Carbon (TOC) shows 0.8-1.1 wt%, compared to the basinal shale 1.5-8 wt%. The shale properties from this outcropped formation indicate a good potential source rock that can be found in the subsurface area with better quality and maturity.

Geochemical characteristics of Tertiary saline lacustrine oils in the Western Qaidam Basin, northwest China

International Nuclear Information System (INIS)

Zhu Yangming; Weng Huanxin; Su Aiguo; Liang Digang; Peng Dehua

2005-01-01

Based on the systematic analyses of light hydrocarbon, saturate, aromatic fractions and C isotopes of over 40 oil samples along with related Tertiary source rocks collected from the western Qaidam basin, the geochemical characteristics of the Tertiary saline lacustrine oils in this region was investigated. The oils are characterized by bimodal n-alkane distributions with odd-to-even (C 11 -C 17 ) and even-to-odd (C 18 -C 28 ) predominance, low Pr/Ph (mostly lower than 0.6), high concentration of gammacerane, C 35 hopane and methylated MTTCs, reflecting the high salinity and anoxic setting typical of a saline lacustrine depositional environment. Mango's K 1 values in the saline oils are highly variable (0.99-1.63), and could be associated with the facies-dependent parameters such as Pr/Ph and gammacerane indexes. Compared with other Tertiary oils, the studied Tertiary saline oils are marked by enhanced C 28 sterane abundance (30% or more of C 27 -C 29 homologues), possibly derived from halophilic algae. It is noted that the geochemical parameters of the oils in various oilfields exhibit regular spatial changes, which are consistent with the depositional phase variations of the source rocks. The oils have uncommon heavy C isotopic ratios (-24%o to -26%o) and a flat shape of the individual n-alkane isotope profile, and show isotopic characteristics similar to marine organic matter. The appearance of oleanane and high 24/(24 + 27)-norcholestane ratios (0.57-0.87) in the saline oils and source rocks confirm a Tertiary organic source

Oil sands thickened froth treatment tailings exhibit acid rock drainage potential during evaporative drying.

Science.gov (United States)

Kuznetsov, Petr; Kuznetsova, Alsu; Foght, Julia M; Siddique, Tariq

2015-02-01

Bitumen extraction from oil sands ores after surface mining produces different tailings waste streams: 'froth treatment tailings' are enriched in pyrite relative to other streams. Tailings treatment can include addition of organic polymers to produce thickened tailings (TT). TT may be further de-watered by deposition into geotechnical cells for evaporative drying to increase shear strength prior to reclamation. To examine the acid rock drainage (ARD) potential of TT, we performed predictive analyses and laboratory experiments on material from field trials of two types of thickened froth treatment tailings (TT1 and TT2). Acid-base accounting (ABA) of initial samples showed that both TT1 and TT2 initially had net acid-producing potential, with ABA values of -141 and -230 t CaCO₃ equiv. 1000 t(-1) of TT, respectively. In long-term kinetic experiments, duplicate ~2-kg samples of TT were incubated in shallow trays and intermittently irrigated under air flow for 459 days to simulate evaporative field drying. Leachates collected from both TT samples initially had pH~6.8 that began decreasing after ~50 days (TT2) or ~250 days (TT1), stabilizing at pH~2. Correspondingly, the redox potential of leachates increased from 100-200 mV to 500-580 mV and electrical conductivity increased from 2-5 dS m(-1) to 26 dS m(-1), indicating dissolution of minerals during ARD. The rapid onset and prolonged ARD observed with TT2 is attributed to its greater pyrite (13.4%) and lower carbonate (1.4%) contents versus the slower onset of ARD in TT1 (initially 6.0% pyrite and 2.5% carbonates). 16S rRNA gene pyrosequencing analysis revealed rapid shift in microbial community when conditions became strongly acidic (pH~2) favoring the enrichment of Acidithiobacillus and Sulfobacillus bacteria in TT. This is the first report showing ARD potential of TT and the results have significant implications for effective management of pyrite-enriched oil sands tailings streams/deposits. Copyright © 2014

Chaos in oil prices? Evidence from futures markets

International Nuclear Information System (INIS)

Adrangi, B.; Chatrath, A.; Dhanda, K.K.; Raffiee, K.

2001-01-01

We test for the presence of low-dimensional chaotic structure in crude oil, heating oil, and unleaded gasoline futures prices from the early 1980s. Evidence on chaos will have important implications for regulators and short-term trading strategies. While we find strong evidence of non-linear dependencies, the evidence is not consistent with chaos. Our test results indicate that ARCH-type processes, with controls for seasonal variation in prices, generally explain the non-linearities in the data. We also demonstrate that employing seasonally adjusted price series contributes to obtaining robust results via the existing tests for chaotic structure. Maximum likelihood methodologies, that are robust to the non-linear dynamics, lend support for Samuelson's hypothesis on contract-maturity effects in futures price-changes. However, the tests for chaos are not found to be sensitive to the maturity effects in the futures contracts. The results are robust to controls for the oil shocks of 1986 and 1991

Assessment of Appalachian basin oil and gas resources: Utica-Lower Paleozoic Total Petroleum System: Chapter G.10 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

Science.gov (United States)

Ryder, Robert T.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

The Utica-Lower Paleozoic Total Petroleum System (TPS) in the Appalachian Basin Province is named for the Upper Ordovician Utica Shale, which is the source rock, and for multiple lower Paleozoic sandstone and carbonate units that are the important reservoirs. The total organic carbon (TOC) values for the Utica Shale are usually greater than 1 weight percent. TOC values ranging from 2 to 3 weight percent outline a broad, northeast-trending area that extends across western and southern Pennsylvania, eastern Ohio, northern West Virginia, and southeastern New York. The Utica Shale is characterized by type II kerogen, which is a variety of kerogen that is typically prone to oil generation. Conondont color-alteration index (CAI) isograds, which are based on samples from the Upper Ordovician Trenton Limestone (or Group), indicate that a pod of mature Utica Shale source rocks occupies most of the TPS.

Multivariate statisticalmethods applied to interpretation of saturated biomarkers (Velebit oil field, SE Pannonian Basin, Serbia

Directory of Open Access Journals (Sweden)

TATJANA SOLEVIC

2006-07-01

Full Text Available Twenty-five crude oils originating from the Velebit oil field (SE Pannonian Basin, the most important oil field in Serbia, were investigated. Saturated biomarkers (n-alkanes, isoprenoids, steranes and triterpanes were analyzed by gas chromatography-mass spectrometry (GC-MS. Based on the distribution and abundance of these compounds, a large number of source and maturation parameters were calculated, particularly those most often used in correlation studies of oils. The examined samples were classified according to their origin and level of thermal maturity using factor, cluster and discriminant analyses. According to the source and maturation parameters, combined factor and cluster analyses using the Ward method enabled the categorization of the investigated oils into three groups. The cluster Ward analysis was shown to be of greater susceptibility and reliability. However, in addition to the two aforementioned methods, K-Means cluster analysis and discriminant analysis were shown to be necessary for a more precise and detailed categorization in the case of a large number of samples in one group. Consequently, it was concluded that factor and cluster K-Means andWard analyses can generally be used for the interpretation of saturated biomarkers in correlation studies of oils, but the observed results have to be checked, i.e., confirmed by discriminant analysis.

Energy fluxes in oil palm plantations as affected by water storage in the trunk

Science.gov (United States)

Meijide, Ana; Röll, Alexander; Fan, Yuanchao; Herbst, Mathias; Niu, Furong; Tiedemann, Frank; June, Tania; Rauf, Abdul; Hölscher, Dirk; Knohl, Alexander

2017-04-01

Oil palm is increasingly expanding, particularly in Indonesia, but information on water and energy fluxes in oil palm plantations is still very limited and on how those are affected by environmental conditions or oil palm age. Using the eddy covariance technique, we studied turbulent fluxes of sensible (H) and latent (LE) heat and gross primary production (GPP) for 8 months each in a young oil palm plantation (1-year old) and subsequently in a mature plantation (12-year old) in Jambi Province, Sumatra, Indonesia. We measured transpiration (T) simultaneously using a sap flux technique. The energy budget was dominated by LE in both plantations, particularly in the mature one, where it represented up to 70% of the available energy. In the young oil palm plantation, evapotranspiration (ET) was significantly reduced and H fluxes were higher. This affected the Bowen ratio, defined as the ratio of H and LE, which was higher in the 1-year old plantation (0.67±0.33), where it remained constant during the day, than in the mature plantation (0.14±0.09), where it varied considerably over the day, suggesting that water accumulated inside the canopy. Using the Community Land Model (CLM), a process based land surface model that has been adapted to oil palm functional traits (i.e. CLM-Palm), we investigated the contribution of different water sources to the measured fluxes. CLM-Palm differentiates leaf and stem surfaces in modelling water interception and is therefore able to diagnose the fraction of dry leaves that contribute to T and the wet fraction of all vegetation surfaces (leaf and stem) that contributes to evaporation. Results from our simulations strengthen our hypothesis of significant contribution of canopy evaporation to ET. As observed in the field, water accumulates inside the canopy in the mature plantation in oil palm trunk surfaces including epiphytes, creating water reservoirs in the trunk, which potentially contribute to ET when they evaporate. The decoupling

Enhanced Oil Recovery with Application of Enzymes

DEFF Research Database (Denmark)

Khusainova, Alsu

Enzymes have recently been reported as effective enhanced oil recovery (EOR) agents. Both laboratory and field tests demonstrated significant increase in the ultimate oil production. Up to16% of additional oil was produced in the laboratory conditions and up to 269 barrels of additional oil per day...... were recovered in the field applications. The following mechanisms were claimed to be responsible for the enhancement of the oil production due to enzymes: wettability improvement of the rock surface; formation of the emulsions; reduction of oil viscosity; and removal of high molecular weight paraffins....... However, the positive effect of enzymes on oil recovery is not that obvious. In most of the studies commercial enzyme products composed of enzymes, surfactants and stabilisers were used. Application of such samples makes it difficult to assign a positive EOR effect to a certain compound, as several...

Aplicación de los métodos de pirólisis Rock-Eval y Fischer al estudio de la materia orgánica contenida en rocas sedimentarias de Guipúzcoa

Directory of Open Access Journals (Sweden)

González G., A.

1987-08-01

Full Text Available The sedimentary rocks are geochemically studied throughout the geological history of the provinces of Guipúzcoa and Vizcaya. The pyrolisis is made following fischer's modified method. On a whole of one hundred and eigthy five samples. We haven't found oil shale, except in Garay (Durango-Vizcaya, where we have managed to distil appreciable quantities of oil from the samples, oscillating between 1.5 l/Tm. and 28 l/Tm. From these ones, whe have choosed twenty which showed a bigger content of organic material than the otheres. We have made the rock-eval pyrolisis with the purpose of checking fischer's modified method. We have managed to define that the petroliferous potential is variable. As for the type of organic material and its stage of evolution (maturity, we have concluded that it is a type II (marine origin with a stage of evolution that places us on the oil generation.Se estudian geoquímicamente rocas sedimentarias a lo largo de la historia geológica de las provincias de Guipúzcoa y Vizcaya. Se realiza la pirólisis según el método modificado de Fischer sobre un total de ciento ochenta y cinco muestras. No se han encontrado rocas bituminosas, salvo en Garay (Durango-Vizcaya donde se han llegado a destilar de las muestras, cantidades apreciables de aceite, que oscilan entre 1,5 l/Tm. y 28 l/Tm. De éstas, hemos escogido veinte que presentaban un contenido mayor de materia orgánica que el resto. Hemos realizado la pirólisis Rock-Eval de ellas con el fin de contrastar el método modificado de Fischer. Hemos llegado a definir que el potencial petrolífero es variable. En cuanto al tipo de materia orgánica y su grado de evolución (madurez, hemos concluido que se trata de un tipo II (origen marino, con un grado de evolución que nos coloca en la ventana de generación de aceite.

CO₂ Storage and Enhanced Oil Recovery: Bald Unit Test Site, Mumford Hills Oil Field, Posey County, Indiana

Energy Technology Data Exchange (ETDEWEB)

Frailey, Scott M. [Illinois State Geological Survey, Champaign, IL (United States); Krapac, Ivan G. [Illinois State Geological Survey, Champaign, IL (United States); Damico, James R. [Illinois State Geological Survey, Champaign, IL (United States); Okwen, Roland T. [Illinois State Geological Survey, Champaign, IL (United States); McKaskle, Ray W. [Illinois State Geological Survey, Champaign, IL (United States)

2012-03-30

The Midwest Geological Sequestration Consortium (MGSC) carried out a small-scale carbon dioxide (CO₂) injection test in a sandstone within the Clore Formation (Mississippian System, Chesterian Series) in order to gauge the large-scale CO₂ storage that might be realized from enhanced oil recovery (EOR) of mature Illinois Basin oil fields via miscible liquid CO₂ flooding.

Canada's crude oil resources : crude oil in our daily lives

International Nuclear Information System (INIS)

Bott, R.

2001-10-01

Created in 1975, the Petroleum Communication Foundation is a not-for-profit organization. The objective of the Foundation is to inform Canadians about the petroleum industry in Canada. It produces educational, fact-based publications and programs, employing a multi-stakeholder review process. The first section of this publication is devoted to crude oil and the benefits that are derived from it. It begins by providing a brief definition of crude oil, then moves to the many uses in our daily lives and the environmental impacts like air pollution, spills, and footprint on the land from exploration and production activities. Section 2 details the many uses of crude oil and identifies the major oil producing regions of Canada. A quick mention is made of non-conventional sources of crude oil. The search for crude oil is the topic of section 3 of the document, providing an overview of the exploration activities, the access rights that must be obtained before gaining access to the resource. The drilling of oil is discussed in section 4. Section 5 deals with issues pertaining to reservoirs within rocks, while section 6 covers the feeding of the refineries, discussing topics from the movement of oil to market to the refining of the crude oil, and the pricing issues. In section 7, the uncertain future is examined with a view of balancing the supply and demand, as crude oil is a non-renewable resource. Supplementary information is provided concerning additional publications published by various organizations and agencies. figs

A new perspective of particle adsorption: Dispersed oil and granular materials interactions in simulated coastal environment.

Science.gov (United States)

Meng, Long; Bao, Mutai; Sun, Peiyan

2017-09-15

This study, adsorption behaviors of dispersed oil in seawaters by granular materials were explored in simulation environment. We quantitatively demonstrated the dispersed oil adsorbed by granular materials were both dissolved petroleum hydrocarbons (DPHs) and oil droplets. Furthermore, DPHs were accounted for 42.5%, 63.4%, and 85.2% (35.5% was emulsion adsorption) in the adsorption of dispersed oil by coastal rocks, sediments, and bacterial strain particles respectively. Effects of controlling parameters, such as temperature, particle size and concentration on adsorption of petroleum hydrocarbons were described in detail. Most strikingly, adsorption concentration was followed a decreasing order of bacterial strain (0.5-2μm)>sediments (0.005-0.625mm)>coastal rocks (0.2-1cm). With particle concentration or temperature increased, adsorption concentration increased for coastal rocks particle but decreased for sediments particle. Besides, particle adsorption rate of petroleum hydrocarbons (n-alkanes and PAHs) was different among granular materials during 60 days. Copyright © 2017 Elsevier Ltd. All rights reserved.

Experimental investigation of wettability alteration on residual oil saturation using nonionic surfactants: Capillary pressure measurement

Directory of Open Access Journals (Sweden)

Masoud Amirpour

2015-12-01

Full Text Available Introducing the novel technique for enhancing oil recovery from available petroleum reservoirs is one of the important issues in future energy demands. Among of all operative factors, wettability may be the foremost parameter affecting residual oil saturation in all stage of oil recovery. Although wettability alteration is one of the methods which enhance oil recovery from the petroleum reservoir. Recently, the studies which focused on this subject were more than the past and many contributions have been made on this area. The main objective of the current study is experimentally investigation of the two nonionic surfactants effects on altering wettability of reservoir rocks. Purpose of this work is to change the wettability to preferentially the water-wet condition. Also reducing the residual oil saturation (Sor is the other purpose of this work. The wettability alteration of reservoir rock is measured by two main quantitative methods namely contact angle and the USBM methods. Results of this study showed that surfactant flooding is more effective in oil-wet rocks to change their wettability and consequently reducing Sor to a low value. Cedar (Zizyphus Spina Christi is low priced, absolutely natural, and abundantly accessible in the Middle East and Central Asia. Based on the results, this material can be used as a chemical surfactant in field for enhancing oil recovery.

Oil and Gas in the Netherlands - Is there a future?

NARCIS (Netherlands)

Herber, R.; de Jager, J.

The impact of oil and, in particular, gas fields discovered in the Dutch subsurface has been very significant. However, 50 years after the discovery of the giant Groningen gas field the Netherlands has become very mature for exploration of oil and gas, and the gas volume left to be discovered in

Discussion of oil pollution in Argentina

Energy Technology Data Exchange (ETDEWEB)

1978-06-01

Oil pollution in Argentina, at the port of Comodora Rivadavia showed signs of long-term oil pollution of a nature which would not be tolerated in relation to the exploitation of North Sea oil. The field is operated by Yacimientos Petroliferos Fiscales (Argentine), produces 70,000 bbl/day of oil from onshore and offshore wells, and has been in operation since 1907. A very marked ''tideline'' of bituminous oil residues contaminates the harbor installations and completely covers the pebbles, boulders, and rocks in the intertidal region. This material is of a considerable thickness and has completely obliterated any form of littoral marine life in these habitats. The sandy beach does not show signs of accumulative oil, and it is used as an important recreational area. Since seriously oiled seabirds can be seen, it is surprising that Patagonian crested ducks, king cormorants, and kelp gulls occur in large numbers but show little sign of oil contamination. The Magellan penguin, which is much less abundant locally, may have been much more vulnerable to the oil.

Influence of the fruit's ripeness on virgin olive oil quality.

Science.gov (United States)

Franco, Ma Nieves; Sánchez, Jacinto; De Miguel, Concepción; Martínez, Manuel; Martín-Vertedor, Daniel

2015-01-01

Virgin Olive Oil (VOO) is a product much demanded by consumers looking for the highest quality and certain traits considered to be typical of the Mediterranean area. The olive fruit's properties and the industry-regulated physicochemical and sensory parameters of seven cultivars were evaluated during the ripening process. In general, the oil percentage in both the wet and dry material increased for all the cultivars from the green to the spotted stages of maturation, and they stayed constant statistically until the ripe stage with just a few exceptions. The lowest oil content was observed in the Manzanilla Cacereña cultivar in all stages of maturation. The cultivars that presented the lowest oil yields in the Abencor system were Manzanilla Cacereña and Carrasqueña, and the highest Corniche. In general, all the cultivars except one presented good behaviour during the mixing process, the exception being Manzanilla Cacereña which presented the lowest values of the extractability percentage. The moisture content of the olives presented a common pattern, increasing from the green to the spotted stage, with the differences being significant in the Corniche, Picual, and Verdial de Badajoz cultivars. All the oils analysed were classified into the "extra virgin" category according to the results for the regulated parameters. The fruity, bitter, and pungent attributes decreased during ripening in all the cultivars studied. In the green stage of maturation, Arbequina had the least intensity of bitterness and pungency, but there were no significant differences among cultivars in the fruity attribute.

Do high oil prices justify an increase in taxation in a mature oil province? The case of the UK continental shelf

International Nuclear Information System (INIS)

Nakhle, Carole

2007-01-01

In response to the structural shift in oil price coupled with greater import dependency, concerns about security of supply have once again emerged as a major policy issue. The UK, the largest producer of oil and natural gas in the European Union, became a net importer of natural gas in 2004, and according to Government estimates will become a net importer of oil by the end of the decade. A weakened North Sea performance means extra reliance, both for the UK and Europe as a whole, on global oil and gas network and imports. In 2002, the UK Government introduced a 10% supplementary charge and in 2005, doubled the charge to 20% in an attempt to capture more revenues from the oil industry as a result of the increase in the price of crude oil. However, higher tax rates do not necessarily generate higher fiscal revenue and in the long term may result in materially lower revenues if investment is discouraged as indeed occurred when the 2007 UK Annual Budget statement showed a shortfall in North Sea oil revenues below forecasts of Pounds 4 billion. It is therefore argued that the increase in the fiscal take came at the wrong time for the UK Continental Shelf and that the UK Government's concern should have been to encourage more oil production from its declining province, especially in the light of the rising concern surrounding the security of supply

Geochemistry and habitat of the oils in Italy

Energy Technology Data Exchange (ETDEWEB)

Mattavelli, L.; Novelli, L. (Agip S.p.A., Milano (Italy))

1990-10-01

All varieties of liquid petroleum, ranging from condensates (> 50{degree}API) to immature sulfur-rich heavy oils (as low as 5{degree} API), have been found in Italy. However, nonbiodegraded heavy oils account for about 70% of the total original oil in place. Geochemical analyses indicate that 11 oil groups are present in the Italian basins and two main types of source rocks have been identified: Triassic carbonates and Tertiary shales. About 95% of the oils were originated from Middle and Upper Triassic carbonates containing type II kerogen (about 1% total organic carbon (TOC) and 500 mg hydrocarbon/g TOC). Only a relatively minor amount of oil was generated by Tertiary shales containing type III kerogen with TOC generally less than 1%. Timing of generation and migration and bulk properties of oils were controlled by geodynamic histories of the three main Italian geologic settings: (1) Apennine and Southern Alp thrust belts, (2) foredeep (depression bordering the thrust belts), and (3) foreland (nondeformed African continental margin). Within the Apennine thrust belts, deep burial during the Neogene resulted in the generation of substantially lighter oils, not only from deeply buried Triassic but sometimes also from Tertiary source rocks. In the late Neogene, foredeep depocenters located in the central Adriatic and southern Sicily, high subsidence (up to 1,000 m/m.y.), a low geothermal gradient (22C/km) and compressional tectonics caused the generation of immature heavy oils generally at depths below 5,000 m and temperatures greater than 100C. Rapid burial and higher geothermal gradients (32C/km), which occurred since the Jurassic, resulted in the generation of light oils from the Late Cretaceous to the Oligocene in the southern sector of Adriatic foreland.

Molecular design of high performance zwitterionic liquids for enhanced heavy-oil recovery processes.

Science.gov (United States)

Martínez-Magadán, J M; Cartas-Rosado, A R; Oviedo-Roa, R; Cisneros-Dévora, R; Pons-Jiménez, M; Hernández-Altamirano, R; Zamudio-Rivera, L S

2018-03-01

Branched gemini zwitterionic liquids, which contain two zwitterionic moieties of linked quaternary-ammonium and carboxylate groups, are proposed as chemicals to be applied in the Enhanced Oil Recovery (EOR) from fractured carbonate reservoirs. The zwitterionic moieties are bridged between them through an alkyl chain containing 12 ether groups, and each zwitterionic moiety has attached a long alkyl tail including a CC double bond. A theoretical molecular mechanism over which EOR could rest, consisting on both the disaggregation of heavy oil and the reservoir-rock wettability alteration, was suggested. Results show that chemicals can both reduce the viscosity and remove heavy-oil molecules from the rock surface. Copyright © 2018. Published by Elsevier Inc.

The use of stable isotopes to trace oil sands constituents

International Nuclear Information System (INIS)

Farwell, A.J.; Nero, V.; Dixon, D.G.

2002-01-01

A study was conducted to determine the biological effects of oil sands mining operations on aquatic ecosystems. The study focused on the Athabasca oil sand deposit, the largest of 4 deposits in northern Alberta. In particular, the study examined the cycling of oil sand constituents in Benthic invertebrates collected from test pits at Syncrude Canada Ltd.. The invertebrates were similar in size, but different in the quantity of process-affected water or mature fine tailings containing residual bitumen. Dragonflies and damselflies in particular, showed trends of depletion for the carbon 13 isotope and enrichment in nitrogen 15 isotope in pits where levels of process affected water was high. The depletion of carbon 13 isotope suggests that oil sand constituents assimilate into the benthic food chain. The greatest carbon 13 depletion, which was approximately 27 per cent, was found to be in test pits with high turbidity. This implies that oil sands constituents degrade microbially instead of by photosynthetic production. All benthic invertebrate group demonstrated an incremental enrichment in nitrogen 15 isotope from the control pit to the pit with greatest levels of mature fine tailings

Geologic distributions of US oil and gas

International Nuclear Information System (INIS)

1992-01-01

This publication presents nonproprietary field size distributions that encompass most domestic oil and gas fields at year-end 1989. These data are organized by geologic provinces as defined by the American Association of Petroleum Geologists' Committee on Statistics of Drilling (AAPG/CSD), by regional geographic aggregates of the AAPG/CSD provinces, and Nationally. The report also provides partial volumetric distributions of petroleum liquid and natural gas ultimate recoveries for three macro-geologic variables: principal lithology of the reservoir rock, principal trapping condition and geologic age of the reservoir rock, The former two variables are presented Nationally and by geographic region, in more detail than has heretofore been available. The latter variable is provided Nationally at the same level of detail previously available. Eighteen tables and 66 figures present original data on domestic oil and gas occurrence. Unfortunately, volumetric data inadequacy dictated exclusion of Appalachian region oil and gas fields from the study. All other areas of the United States known to be productive of crude oil or natural gas through year-end 1989, onshore and offshore, were included. It should be noted that none of the results and conclusions would be expected to substantively differ had data for the Appalachian region been available for inclusion in the study

Secondary and tertiary gas injection in fractured carbonate rock: Experimental study

Energy Technology Data Exchange (ETDEWEB)

Karimaie, H.; Torsaeter, O. [SPE, NTNU (Norway); Darvish, G.R. [SPE, STATOIL (Norway); Lindeberg, E. [SPE, SINTEF (Norway)

2008-09-15

The use of CO{sub 2} has received considerable interest as a method of EOR but a major drawback is its availability and increasing cost. Therefore, as the number of CO{sub 2} injection projects increase, an alternative must be considered to meet the economic considerations. For this reason attention has been directed to nitrogen injection which may be a good substitute for CO{sub 2}. The purpose of the experiments described in this paper was to investigate the efficiency of oil recovery by CO{sub 2} and N{sub 2} in fractured carbonate rock. The combined effects of gravity drainage and component exchange between gas in fracture and oil in matrix on oil recovery in fractured reservoirs subjected to CO{sub 2} or nitrogen gas injection are experimentally studied. Laboratory experiments have been carried out on a low permeable outcrop chalk, as an analogue to a North Sea reservoir rock. This was surrounded by a fracture, established with a novel experimental set-up. The experiments aimed to investigate the potential of oil recovery by secondary and tertiary CO{sub 2} and nitrogen gas injection at high pressure high temperature condition. The matrix block was saturated using recombined binary mixture live oil (C{sub 1}-C{sub 7}), while the fracture was filled with a sealing material to obtain a homogeneous saturation. The sealing material was then removed by increasing the temperature which in turn creates the fracture surrounding the core. Gas was injected into the fracture at pressures above the bubble point of the oil. Oil recovery as a function of time was monitored during the experiments. Results from secondary gas injection experiments indicate that CO{sub 2} injection at elevated pressure and temperature is more efficient than N{sub 2} injection. Results from tertiary gas injection experiments also show that injection of CO{sub 2} could significantly recover the oil, even after waterflooding, compared to N{sub 2} injection. (author)

Participation of civil engineers in designing facilities in rock salt

International Nuclear Information System (INIS)

Duddeck, H.; Westhaus, T.

1990-01-01

For the design of underground facilities in rock salt layers or domes, as caverns for repositories, the civil engineering approach may be useful. The underground openings are analysed by determining the displacements and the stresses for actual states and hypothetical situations. The paper reports on the state of art in the development of suited time dependent material laws for rock salt, on time integration methods for the analysis, and on a possible procedure for a consistent safety analysis. The examples given include caverns filled by oil, analysis of a mine with vertical excavation chambers, and dams closing mine galleries. (orig.) [de

A comparison of geochemical features of extracts from coal-seams source rocks with different polarity solvents

Energy Technology Data Exchange (ETDEWEB)

Chen, Jianping; Deng, Chunping; Wang, Huitong

2009-02-15

There exists a great difference in group-type fractions and biomarker distributions of chloroform extracts from coals and coal-seams oils, which makes the source identification of coal-seams oils in sedimentary basins rather difficult. The experiment, in which four different polarity solvents, n-hexane, benzene, dichloromethane and chloroform, were used to extract 9 coal-seams source rocks and 3 typical lacustrine source rocks, showed that the yield of extracts increased gradually with increasing solvent polarity. The distribution features of their n-alkanes, isoprenoids and sterane and terpane biomarkers remained, in general, similar, showing no distinct enrichment or depletion for a certain fraction by any solvent. The compositional analysis on n-hexane and chloroform extracts showed that the absolute amount (concentration) of biomarkers was relatively low for the n-hexane extract but comparatively high for the chloroform extract, this difference became great among coal-seams source rocks but small among lacustrine mudstones. The statistical analysis on the relative amount of the 18 major biomarkers in n-hexane and chloroform extracts from 10 source rock samples showed that extracts with a proportional error for the same biomarker of less than 5% (including the analytical error) accounted for 84% while those with a proportional error over 10% amounted to below 5%. This suggested that the outcome of oil-source correlation made by these biomarkers will be independent of variations in amounts of saturates and biomarkers arising from solvent polarity. Therefore, biomarkers obtained from organic-rich source rocks including coals by the extraction with the commonly used chloroform solvent can be applied for the oilsource correlation of coal-seams petroliferous basins.

Enhanced Oil Recovery with Surfactant Flooding

DEFF Research Database (Denmark)

Sandersen, Sara Bülow

, thus reducing the interfacial tension (IFT) to ultra low (0.001 mN/m), which consequently will mobilize the residual oil and result in improved oil recovery. This EOR technology is, however, made challenging by a number of factors, such as the adsorption of surfactant and co-surfactant to the rock...... be resistant to and remain active at reservoir conditions such as high temperatures, pressures and salinities. Understanding the underlying mechanisms of systems that exhibit liquid-liquid equilibrium (e.g. oil-brine systems) at reservoir conditions is an area of increasing interest within EOR. This is true...... studied. The effect of increased pressure became more significant when combined with increasing temperature. The experiments performed on the oil/ seawater systems were similar to the high pressure experiments for the surfactant system discussed above. Oil was contacted with different brine solutions...

Technological advancements revitalize conventional oil sector

International Nuclear Information System (INIS)

Thomson, L.

2000-01-01

Maturing reserves in the Western Canada Sedimentary Basin is resulting in a gradual shift of focus from huge new discoveries and wildcat gushers to developing new technologies for exploration and enhanced recovery techniques of production, keeping costs down and reducing environmental impacts, as a means of keeping conventional oil plays a viable force in the oil and gas industry. The value in refocusing efforts towards technology development is given added weight by a recent announcement by the Petroleum Communication Foundation, which stated that in addition to the oil sands and offshore oil and gas developments, one of the country's largest undeveloped oil resource is the 70 per cent of discovered crude oil in western Canadian pools that cannot be recovered by current conventional production techniques. Therefore, development of new technologies to exploit these currently unrecoverable resources is a matter of high priority. To remain competitive, the new techniques must also lower the cost of recovering oil from these sources, given that the cost of oil production in Canada is already higher than that in most other competing countries

Detailed description of oil shale organic and mineralogical heterogeneity via fourier transform infrared mircoscopy

Science.gov (United States)

Washburn, Kathryn E.; Birdwell, Justin E.; Foster, Michael; Gutierrez, Fernando

2015-01-01

Mineralogical and geochemical information on reservoir and source rocks is necessary to assess and produce from petroleum systems. The standard methods in the petroleum industry for obtaining these properties are bulk measurements on homogenized, generally crushed, and pulverized rock samples and can take from hours to days to perform. New methods using Fourier transform infrared (FTIR) spectroscopy have been developed to more rapidly obtain information on mineralogy and geochemistry. However, these methods are also typically performed on bulk, homogenized samples. We present a new approach to rock sample characterization incorporating multivariate analysis and FTIR microscopy to provide non-destructive, spatially resolved mineralogy and geochemistry on whole rock samples. We are able to predict bulk mineralogy and organic carbon content within the same margin of error as standard characterization techniques, including X-ray diffraction (XRD) and total organic carbon (TOC) analysis. Validation of the method was performed using two oil shale samples from the Green River Formation in the Piceance Basin with differing sedimentary structures. One sample represents laminated Green River oil shales, and the other is representative of oil shale breccia. The FTIR microscopy results on the oil shales agree with XRD and LECO TOC data from the homogenized samples but also give additional detail regarding sample heterogeneity by providing information on the distribution of mineral phases and organic content. While measurements for this study were performed on oil shales, the method could also be applied to other geological samples, such as other mudrocks, complex carbonates, and soils.

Leaf water enrichment of stable water isotopes (δ18O and δD) in a mature oil palm plantation in Jambi province, Indonesia.

Science.gov (United States)

Bonazza, Mattia; Tjoa, Aiyen; Knohl, Alexander

2017-04-01

During the last few decades, Indonesia experienced rapid and large scale land-use change towards intensively managed crops, one of them is oil palm. This transition results in warmer and dryer conditions in microclimate. The impacts on the hydrological cycle and on water-use by plants are, however, not yet completely clear. Water stable isotopes are useful tracers of the hydrological processes and can provide means to partition evapotranspiration into evaporation and transpiration. A key parameter, however, is the enrichment of water stable isotope in plant tissue such as leaves that can provide estimates on the isotopic composition of transpiration. Here we present the results of a field campaign conducted in a mature oil palm plantation in Jambi province, Indonesia. We combined continuous measurements of water vapor isotopic composition and mixing ratio with isotopic analysis of water stored in different pools like oil palm leaves, epiphytes, trunk organic matter and soil collected over a three days period. Leaf enrichment varied from -2 ‰ to 10 ‰ relative to source (ground) water. The temporal variability followed Craig and Gordon model predictions for leaf water enrichment. An improved agreement was reached after considering the Péclet effect with an appropriate value of the characteristic length (L). Measured stomatal conductance (gs) on two different sets of leaves (top and bottom canopy) was mainly controlled by radiation (photosynthetically active radiation) and vapor pressure deficit. We assume that this control could be explained in conditions where soil water content is not representing a limiting factor. Understanding leaf water enrichment provides one step towards partitioning ET.

(Discussion of) oil pollution in Argentina

Energy Technology Data Exchange (ETDEWEB)

1978-06-01

The port of Comodora Rivadavia shows signs of long-term oil pollution of a nature which would not be tolerated in relation to the exploitation of North Sea oil. The field is operated by Yacimientos Petroliferos Fiscales (Argentine), produces 70,000 bbl/day of oil from onshore and offshore wells, and has been in operation since 1907. A very marked tideline of bituminous oil residues contaminates the harbor installations and completely covers the pebbles, boulders, and rocks in the inertidal region. This material is of a considerable thickness and has completely obliterated any form of littoral marine life in these habitats. The sandy beach does not show signs of accumulative oil, and it is used as an important recretional area. Since seriously oiled seabirds can be seen, it is surprising that Patagonian crested ducks, king cormorants, and kelp gulls occur in large numbers but show little sign of oil contamination. The Magellan penguin, which is much less abundant locally, may have been much more vulnerable to the oil. Photographs are included.

Correlation between dental maturity and cervical vertebral maturity.

Science.gov (United States)

Chen, Jianwei; Hu, Haikun; Guo, Jing; Liu, Zeping; Liu, Renkai; Li, Fan; Zou, Shujuan

2010-12-01

The aim of this study was to investigate the association between dental and skeletal maturity. Digital panoramic radiographs and lateral skull cephalograms of 302 patients (134 boys and 168 girls, ranging from 8 to 16 years of age) were examined. Dental maturity was assessed by calcification stages of the mandibular canines, first and second premolars, and second molars, whereas skeletal maturity was estimated by the cervical vertebral maturation (CVM) stages. The Spearman rank-order correlation coefficient was used to measure the association between CVM stage and dental calcification stage of individual teeth. The mean chronologic age of girls was significantly lower than that of boys in each CVM stage. The Spearman rank-order correlation coefficients between dental maturity and cervical vertebral maturity ranged from 0.391 to 0.582 for girls and from 0.464 to 0.496 for boys (P cervical vertebral maturation stage. The development of the mandibular second molar in females and that of the mandibular canine in males had the strongest correlations with cervical vertebral maturity. Therefore, it is practical to consider the relationship between dental and skeletal maturity when planning orthodontic treatment. Copyright © 2010 Mosby, Inc. All rights reserved.

Estimation Of Height Of Oil -Water Contact Above Free Water Level ...

African Journals Online (AJOL)

An estimate of oil-water contact (OWC) and the understanding of the capillary behaviour of hydrocarbon reservoirs are vital for optimum reservoir characterization, hydrocarbon exploration and production. Hence, the height of oil-water contact above free water level for different rock types from some Niger Delta reservoirs ...

Wet separation processes as method to separate limestone and oil shale

Science.gov (United States)

Nurme, Martin; Karu, Veiko

2015-04-01

Biggest oil shale industry is located in Estonia. Oil shale usage is mainly for electricity generation, shale oil generation and cement production. All these processes need certain quality oil shale. Oil shale seam have interlayer limestone layers. To use oil shale in production, it is needed to separate oil shale and limestone. A key challenge is find separation process when we can get the best quality for all product types. In oil shale separation typically has been used heavy media separation process. There are tested also different types of separation processes before: wet separation, pneumatic separation. Now oil shale industry moves more to oil production and this needs innovation methods for separation to ensure fuel quality and the changes in quality. The pilot unit test with Allmineral ALLJIG have pointed out that the suitable new innovation way for oil shale separation can be wet separation with gravity, where material by pulsating water forming layers of grains according to their density and subsequently separates the heavy material (limestone) from the stratified material (oil shale)bed. Main aim of this research is to find the suitable separation process for oil shale, that the products have highest quality. The expected results can be used also for developing separation processes for phosphorite rock or all others, where traditional separation processes doesn't work property. This research is part of the study Sustainable and environmentally acceptable Oil shale mining No. 3.2.0501.11-0025 http://mi.ttu.ee/etp and the project B36 Extraction and processing of rock with selective methods - http://mi.ttu.ee/separation; http://mi.ttu.ee/miningwaste/

Natural gas hydrate formation and inhibition in gas/crude oil/aqueous systems

DEFF Research Database (Denmark)

Daraboina, Nagu; Pachitsas, Stylianos; von Solms, Nicolas

2015-01-01

Gas hydrate formation in multi phase mixtures containing an aqueous phase (with dissolved salts), reservoir fluid (crude oil) and natural gas phase was investigated by using a standard rocking cell (RC-5) apparatus. The hydrate formation temperature was reduced in the presence of crude oils...... can contribute to the safe operation of sub sea pipelines in the oil and gas industry....

Hydrophobically associated polymers for wettability alteration and enhanced oil recovery – Article review

Directory of Open Access Journals (Sweden)

A.N. El-hoshoudy

2017-09-01

Full Text Available Crude oil and other petroleum products are crucial to the global economy today due to increasing energy demand approximately (∼1.5% per year and significant oil remaining after primary and secondary oil recovery (∼45–55% of original oil in place, OOIP, which accelerates the development of enhanced oil recovery (EOR technologies to maximize the recovered oil amount by non-conventional methods as polymer flooding. This review discusses enhanced oil recovery methods specially polymer flooding techniques and their effects on rock wettability alteration.

Fluids in crustal deformation: Fluid flow, fluid-rock interactions, rheology, melting and resources

Science.gov (United States)

Lacombe, Olivier; Rolland, Yann

2016-11-01

Fluids exert a first-order control on the structural, petrological and rheological evolution of the continental crust. Fluids interact with rocks from the earliest stages of sedimentation and diagenesis in basins until these rocks are deformed and/or buried and metamorphosed in orogens, then possibly exhumed. Fluid-rock interactions lead to the evolution of rock physical properties and rock strength. Fractures and faults are preferred pathways for fluids, and in turn physical and chemical interactions between fluid flow and tectonic structures, such as fault zones, strongly influence the mechanical behaviour of the crust at different space and time scales. Fluid (over)pressure is associated with a variety of geological phenomena, such as seismic cycle in various P-T conditions, hydrofracturing (including formation of sub-horizontal, bedding-parallel veins), fault (re)activation or gravitational sliding of rocks, among others. Fluid (over)pressure is a governing factor for the evolution of permeability and porosity of rocks and controls the generation, maturation and migration of economic fluids like hydrocarbons or ore forming hydrothermal fluids, and is therefore a key parameter in reservoir studies and basin modeling. Fluids may also help the crust partially melt, and in turn the resulting melt may dramatically change the rheology of the crust.

Use of ``rock-typing`` to characterize carbonate reservoir heterogeneity. Final report

Energy Technology Data Exchange (ETDEWEB)

Ikwuakor, K.C.

1994-03-01

The objective of the project was to apply techniques of ``rock-typing`` and quantitative formation evaluation to borehole measurements in order to identify reservoir and non-reservoir rock-types and their properties within the ``C`` zone of the Ordovician Red River carbonates in the northeast Montana and northwest North Dakota areas of the Williston Basin. Rock-typing discriminates rock units according to their pore-size distribution. Formation evaluation estimates porosities and pore fluid saturation. Rock-types were discriminated using crossplots involving three rock-typing criteria: (1) linear relationship between bulk density and porosity, (2) linear relationship between acoustic interval transit-time and porosity, and (3) linear relationship between acoustic interval transit-time and bulk density. Each rock-type was quantitatively characterized by the slopes and intercepts established for different crossplots involving the above variables, as well as porosities and fluid saturations associated with the rock-types. All the existing production was confirmed through quantitative formation evaluation. Highly porous dolomites and anhydritic dolomites contribute most of the production, and constitute the best reservoir rock-types. The results of this study can be applied in field development and in-fill drilling. Potential targets would be areas of porosity pinchouts and those areas where highly porous zones are downdip from non-porous and tight dolomites. Such areas are abundant. In order to model reservoirs for enhanced oil recovery (EOR) operations, a more localized (e.g. field scale) study, expanded to involve other rock-typing criteria, is necessary.

A local oil spill revisited

International Nuclear Information System (INIS)

Teal, J.M.

1993-01-01

In October 1969 George Hampson and Howard Sanders (Woods Hole Oceanographic Institution) described a 'Local Oil Spill' in Oceanus. The spill had occurred a month before when the barge Florida, loaded with no. 2 fuel oil, ran into some rocks in Buzzards Bay off West Falmouth, Massachusetts. In the summer of 1989, almost 20 years later, They visited the Wild Harbor marsh area that had suffered the greatest impact from the spill to see if any traces of the event in the marsh ecosystem could be found. During those 20 years, the site has been visited by graduate students in marine ecology, by reporters seeking information about current oil spills but also interested in seeing the effects of the Wild Harbor spill, and by visiting scientists curious about one of the world's best-studied oil spills. For more than a decade after the spill, an oil sheen appeared on the surface of the water when mud from the most heavily oiled parts of the marsh was disturbed. During the second decade, the marsh's appearance returned to normal

Identification and Isolation of Protein Markers Associated with Somatic Embryogenesis in Oil Palm

Institute of Scientific and Technical Information of China (English)

Chin Chiew Foan; Nguyen Thi Thuy Van

2012-01-01

Oil palm is an important oil bearing crop with the highest oil yield per hectare per year.About 90％ of the world palm oil produced is used as vegetable oil while the remaining 10％ is for non-food products such as oleochemicals and cosmetics.The high world demand for vegetable oil and increasingly the conversion of vegetable oil into biofuel,has prompted the oil palm industries to seek for high oil yielding seedlings.As oil palm has only a single meristem and full inbred lines were absent,propagation of elite oil palm through cutting or grafting is not possible.Clonal propagation through tissue culture offers a potential means for mass production of elite oil palm.Many oil palm laboratories have clonal propagated elite oil palm propagules through somatic embryogenesis.This study deployed 2DE coupled with LC MS/MS mass spectrometry to isolate protein markers associated with the initial stage of somatic embryogenesis i.e.callus proliferation.The isolated markers can then be used in early selection to screen for calli with high proliferation rate.Since amenability of explant is strongly correlated with maturity of the explants,proteomic analysis was focussed on isolating proteins associated with leaf maturity.Subsequently,comparisons were made on leaf with the same stage of maturity but with different callus proliferation rates.Quantitative analysis showed that there were a total of 67,77 and 4 protein spots to be present only in the young,medium and old leaves,respectively.While low and high proliferation leaves containing about the same amount of proteins,i.e.660 and 694 protein spots respectively.Interestingly,proteins with molecular weight of less than 25 kDa or had pl value lower than 5 were abundant only in leaves with high proliferation rate.Three spots with significant difference in expression by 2-fold among different growth stages were identified as protein subunits of ATP synthase (ATPE_LIRTU),Ribulose bisphosphate carboxylase (RBL_AMOTI) and a putative

Oil synthesis and composition in developidng cotyledons of groundnut

Energy Technology Data Exchange (ETDEWEB)

Kumar, Niranjan; Srivastava, K N; Sharma, N D; Mehta, S L [Indian Agricultural Research Inst., New Delhi (India). Div. of Biochemistry

1988-03-01

Oil synthesis in groundnut mutants TG-1 and TG-16 along with its parent Spanish Improved was studied during kernel development. Dry weight, oil and protein content increased progressively with kernel development. Acetate 2-{sup 14}C incorporation in lipids increased in both the mutants during development, while in parent it increased up to 95 day stage and then showed a decline at maturity. However, during development the rate of incorporation per kernel was lower in parent than mutants. Polar lipids decreased while non-polar lipids increased during development both in parent as well as mutants. Fatty acid composition of the oil differed between mutants and also from the parent during development. TG-16 had higher oleic and lower linoleic than parent Spanish Improved while TG-1 had intermediate oleic acid levels. During development, palmitate decreased slightly in parent while in TG-1 and TG-16, the decrease at maturity was lesser than the parent. The other fatty acid present in minor amounts, showed variation which was neither characteristic of the variety nor of any stage. Results, thus indicate developmental differences with respect to oil content and quality between mutant and parent. (author). 21 refs.

Oil synthesis and composition in developidng cotyledons of groundnut

International Nuclear Information System (INIS)

Kumar, Niranjan; Srivastava, K.N.; Sharma, N.D.; Mehta, S.L.

1988-01-01

Oil synthesis in groundnut mutants TG-1 and TG-16 along with its parent Spanish Improved was studied during kernel development. Dry weight, oil and protein content increased progressively with kernel development. Acetate 2- 14 C incorporation in lipids increased in both the mutants during development, while in parent it increased up to 95 day stage and then showed a decline at maturity. However, during development the rate of incorporation per kernel was lower in parent than mutants. Polar lipids decreased while non-polar lipids increased during development both in parent as well as mutants. Fatty acid composition of the oil differed between mutants and also from the parent during development. TG-16 had higher oleic and lower linoleic than parent Spanish Improved while TG-1 had intermediate oleic acid levels. During development, palmitate decreased slightly in parent while in TG-1 and TG-16, the decrease at maturity was lesser than the parent. The other fatty acid present in minor amounts, showed variation which was neither characteristic of the variety nor of any stage. Results, thus indicate developmental differences with respect to oil content and quality between mutant and parent. (author). 21 refs

Efficiency Evaluation of Offshore Deoiling Applications utilizing Real-Time Oil-in-Water Monitors

DEFF Research Database (Denmark)

Hansen, Dennis Severin; Bram, Mads Valentin; Løhndorf, Petar Durdevic

2017-01-01

An increasing water to oil ration in the North Sea oil and gas production motivates for an optimization of the current deoiling facilities. Current facilities are operated on matured methodologies, which in most cases fulfill the government regulations. However, it has also observed...

Optimization of Offshore De-oiling Hydrocyclone Performance

DEFF Research Database (Denmark)

Yang, Zhenyu; Løhndorf, Petar Durdevic; Pedersen, Simon

, along with the facts that the global oil demand will continuously grow by 7 mb/d to 2020 and exceed 99 mb/d in 2035, meanwhile, many production fields turn to be matured and thereby the water flooding technology is more and more employed as a key enhanced oil recovery solution for these fields [9]. Fig......One of the biggest environmental concerns in offshore oil & gas production is the quality of tremendous amounts of produced water discharged into the oceans. Today, in average three barrels of water are produced along with each barrel of oil [9]. This concern will become more severe in the future...... companies, Maersk Oil and Ramboll Oil & Gas A/S, launched a research project HTF-PDPWAC with total budget of 10 million dkk. One of the focuses of this project is to optimization of the de-oiling hydrocyclone performance in order to improve the produced water treatment quality without sacrificing...

Beyond Rock. Social commitment and political conscience through Popular Music in Australia 1976 - 2002. The case of Midnight Oil

Directory of Open Access Journals (Sweden)

Roger Bonastre

2011-03-01

Full Text Available The work and career of Midnight Oil illustrate a case of interaction between culture and politics in Australia. Furthermore they represent an example of social commitment from the sphere of urban popular culture. For a quarter of a century Midnight Oil offered a critical and ideological interpretation of the Australian social and political evolution. Aware of and sensitive to changes and events happening around them, five Sydneysiders thought about Australian identity in terms of what they considered to be their national challenges from a universal perspective. Hence, they approached issues like pacifism, Indigenous rights and environmentalism and developed a social and political discourse based on the defence of human rights and a condemnation of capitalist excesses. Through more than a hundred songs and almost two thousand gigs the band urged politicians to reassess the institutions. At the same time they criticized people’s apathy asking them for a deeper engagement with the development of the country’s welfare. Finally, in December 2002, Peter Garrett quit his singer-activist journey to launch a political career by joining the Australian Labor Party, for which he is the current Minister for School Education, Early Childhood and Youth in the Julia Gillard Government. It is thus that now we can make sense of the extent to which the political and social message of a rock band can actually generate enough credibility to allow for the lead singer´s transition from the stage to parliament.

Concepts of flow in fractured rocks

International Nuclear Information System (INIS)

Black, J.H.

1989-01-01

The role of well testing is considered in the context of tracer tests in fractured rock. It is shown that the important information required by a tracer test includes not just the hydrogeological parameters (transmissivity and storage), but also the geometry of flow. This is usually implicit in well testing, perhaps because the tests are generally interpretationally insensitive to variations in flow geometry. It is also argued that both well and tracer tests change their flow geometry during their lifetime. They often start as pipe flow near a well and change to large scale, almost spherical, flow after long periods of time. The duration of a tracer test is compared with that of a well test and is found to reach an equivalent duration (of dimensionless time) that is at least 10 4 times longer. Care should be exercised in transposing flow geometries derived from mature well tests on to tracer tests which are not similar in dimensionless time. Finally, a 'sinusoidal flow test' is outlined which has prompted a new way of looking at well tests in terms of their flow geometry. The new analysis involves 'partial dimension' of flow and is probably highly appropriate to fissured rocks. Fissured rocks have, for too long, been seen as a regular system of planar, fully transmissive fissures. (author). 12 refs, 4 figs, 1 tab

The origin of gas seeps and shallow gas in northern part of South China Sea

Science.gov (United States)

Li, M.; Jin, X.

2003-04-01

vary in different places. Gas chimneys can be found on seafloor, which show blank zone on seismic profiles, locally with pit holes. The geochemical analyses of gas samples from gas seeps indicate its composition is dominated by hydrocarbon gas, the other include CO_2, N_2 and O_2. The gas has high dry index, and heavier δ13C_1.This shows that the gas is of matured- over matured thermogenic gas. The geochemical characteristics of extracts from sediments in the area are similar to those of penetrated source rock of Neogene in the basin, indicating the gas is from the matured source rock in the basin, the diapric zone and fault act as the migration pathway. The gas samples on slope were obtained through degasification of sediments collected by SONNE. Geochemical analyses show that the gas composition is dominated by methane, with high dry index and heavier δ13C_1, belonging to typical thermogenic gas. On maturity chart, the gas samples on upper slope fall in the area near the boundary of condensate, indicating higher maturity, while those on lower slope has lower maturity and fall in the area near oil window. The gas samples from deep sea basin is mixed gas of thermogenic gas and biogas. Therefore, it is reasonable to consider the deep buried source rock as the origin of the gas, and the active faults are the migration pathway. As stated above, the gas seeps and shallow gas in northern part of South China Sea were mainly originated from deep buried source rock, migrated through diapric zone or active faults. Their distribution and occurrence have directly relation with the source rock type and maturity, and the tectonic active of the underlying basins. The petroleum exploration has proved that Yinggehai basin and Qiongdongnan basin on the western part are favored for gas generation, while the Pearl River Mouth Basin and Beibu Gulf basin on the eastern part are favored for oil generation. This may account for the distribution of gas seeps which concentrated in the

Maturity and maturity models in lean construction

Directory of Open Access Journals (Sweden)

Claus Nesensohn

2014-03-01

Full Text Available In recent years there has been an increasing interest in maturity models in management-related disciplines; which reflects a growing recognition that becoming more mature and having a model to guide the route to maturity can help organisations in managing major transformational change. Lean Construction (LC is an increasingly important improvement approach that organisations seek to embed. This study explores how to apply the maturity models to LC. Hence the attitudes, opinions and experiences of key industry informants with high levels of knowledge of LC were investigated. To achieve this, a review of maturity models was conducted, and data for the analysis was collected through a sequential process involving three methods. First a group interview with seven key informants. Second a follow up discussion with the same individuals to investigate some of the issues raised in more depth. Third an online discussion held via LinkedIn in which members shared their views on some of the results. Overall, we found that there is a lack of common understanding as to what maturity means in LC, though there is general agreement that the concept of maturity is a suitable one to reflect the path of evolution for LC within organisations.

Stepwise Rock-Eval pyrolysis as a tool for typing heterogeneous organic matter in soils

Energy Technology Data Exchange (ETDEWEB)

Hetenyi, M.; Nyilas, T.; Toth, T.M. [Department of Mineralogy, Geochemistry and Petrology, University of Szeged, P.O. Box 651, H-6701 Szeged (Hungary)

2005-08-15

This paper presents an application of Rock-Eval pyrolysis for estimating the proportion of the components with different thermal stability in soil organic matter, the maturity of which corresponds to the early stage of diagenesis. For testing the validity of the modified Rock-Eval method, parallel series of pyrolysis were carried out on sedimentary rock samples. The temperature program was selected on the basis of the results obtained from stepwise Rock-Eval pyrolysis and from the mathematical deconvolution of pyrograms. The proportion of the original biomolecules in soil organic matter was calculated by the integration of pyrograms below 350{sup o}C and could be determined rapidly by one single pyrolysis using 350{sup o}C as initial cracking temperature. At 380{sup o}C, both the mathematical and the experimental methods provide reliable information about the proportion of the humic substances. Conversely, for rock samples, mathematical deconvolution of the pyrograms showed the heterogeneity of the sedimentary organic matter, the maturity of which corresponds to late diagenesis, without any estimation of the proportion of the different components. The rate of organic carbon accumulation in the studied soils and the decomposition rate of biopolymers were interpreted as a function of land-use and redox conditions. Differences in the precursor vegetation and in the environmental parameters resulted in markedly reduced carbon storage and higher degree of humification in the agricultural soil than in the adjacent forest soil. Redox conditions strongly affected both the amount and the elemental composition of the stored organic matter. The decomposition rate of biopolymers appeared to be controlled mainly by the contribution of resistant lignin components to the source biomass and, to a lesser extent, by redox conditions.

Analytical filtration model for nonlinear viscoplastic oil in the theory of oil production stimulation and heating of oil reservoir in a dual-well system

Science.gov (United States)

Ivanovich Astafev, Vladimir; Igorevich Gubanov, Sergey; Alexandrovna Olkhovskaya, Valeria; Mikhailovna Sylantyeva, Anastasia; Mikhailovich Zinovyev, Alexey

2018-02-01

Production of high-viscosity oil and design of field development systems for such oil is one of the most promising directions in the development of world oil industry. The ability of high-viscosity oil to show in filtration process properties typical for non-Newtonian systems is proven by experimental studies. Nonlinear relationship between the pressure gradient and the rate of oil flow is due to interaction of high-molecular substances, in particular, asphaltenes and tars that form a plastic structure in it. The authors of this article have used the analytical model of stationary influx of nonlinear viscoplastic oil to the well bottom in order to provide rationale for the intensifying impact on a reservoir. They also have analyzed the method of periodic heating of productive reservoir by means of dual-wells. The high-temperature source is placed at the bottom of the vertical well, very close to the reservoir; at the same time the side well, located outside the zone of expected rock damage, is used for production. Suggested method of systemic treatment of reservoirs with dual wells can be useful for small fields of high-viscosity oil. The effect is based on the opportunity to control the structural and mechanical properties of high-viscosity oil and to increase depletion of reserves.

Odd man in the oil patch

International Nuclear Information System (INIS)

1994-01-01

Oil companies are taking a serious look at ways to cut exploration costs. Conventional hydrocarbon finding technologies is based on geological and seismic work. Geological data can cost thousands of dollars. A new method being reviewed is that of surface technology that tests soil and rock for signs of hydrocarbons that have migrated from underground pools to or near the surface. The techniques range from testing for the presence of microbes that consume hydrocarbons to radioactive imprints. Members of the oil industry are looking for the competitive edge by reducing exploration costs, using new surface technology to reduce the cost of a barrel of oil, and by increasing the success rate in finding economically feasible hydrocarbons

Effects of Microwave Radiation on Oil Recovery

Science.gov (United States)

Esmaeili, Abdollah

2011-12-01

A variety of oil recovery methods have been developed and applied to mature and depleted reservoirs in order to improve the efficiency. Microwave radiation oil recovery method is a relatively new method and has been of great interest in the recent years. Crude oil is typically co-mingled with suspended solids and water. To increase oil recovery, it is necessary to remove these components. The separation of oil from water and solids using gravitational settling methods is typically incomplete. Oil-in-water and oil-water-solid emulsions can be demulsified and separated into their individual layers by microwave radiation. The data also show that microwave separation is faster than gravity separation and can be faster than conventional heating at many conditions. After separation of emulsion into water and oil layers, water can be discharged and oil is collected. High-frequency microwave recycling process can recover oil and gases from oil shale, residual oil, drill cuttings, tar sands oil, contaminated dredge/sediments, tires and plastics with significantly greater yields and lower costs than are available utilizing existing known technologies. This process is environmentally friendly, fuel-generating recycler to reduce waste, cut emissions, and save energy. This paper presents a critical review of Microwave radiation method for oil recovery.

Lower Cretaceous Source Rock and its Implication for the Gulf of Guinea Petroleum System

International Nuclear Information System (INIS)

Frost, B.R.; Griffith, R.C.

2002-01-01

Current petroleum system models for the Gulf of Guinea propose Tertiary-age deltaic organic material as the principal source for the hydrocarbons found there. Although previous workers recognized numerous difficulties and inconsistencies, no alternative model has been resented to adequately explain the complete petroleum system. We propose that the principal source rock for the Gulf of Guinea system occurs in upper lower Cretaceous-age shales at the rift-drift transition. Tertiary loading and the consequent maturation of this lower Cretaceous source rock can explain the controls on tap formation, reservoir distribution and hydrocarbon types found in the Gulf of Guinea

Optimization of supplementary recovery projects for mature fields; Otimizacao de projetos de recuperacao suplementar para campos com alto grau de explotacao

Energy Technology Data Exchange (ETDEWEB)

Marsili, Marcelo D.; Castineira, Paula P.; Couto, Paulo; Sa Neto, Abelardo de; Ferreira Filho, Virgilio J.M. Ferreira Filho [Universidade Federal do Rio de Janeiro, RJ (Brazil). Curso de Engenharia de Petroleo

2008-07-01

Development of mature oil fields has been a key issue in a world scenario of high crude oil prices, declining reserves and political instability in the main producing regions. This paper proposes a discussion about different secondary recovery projects for a hypothetical mature field subjected to water injection into the reservoir. The reservoir model was built using a numeric black oil simulator, taking into account several heterogeneities associated to real reservoirs, thus being able to predict near-realistic performances. The model was implemented and it was simulated a primary production for 11 years under solution gas drive and weak water influx and gas cap drive mechanisms. During the course of production, reservoir pressure decreased substantially. Five waterflooding projects were suggested as a remedy to restore the reservoir pressure and well productivities. Results were obtained by numerical simulation and compared by the net present value (NPV) economic criteria of project analysis. After the simulation of 36 years of production considering waterflooding, the most attractive project proved to be the five-spot pattern, with a 40% estimated oil recovery and 60 million dollars NPV for a fixed crude oil price of 70 dollars per barrel. (author)

Gold and oil futures markets: Are markets efficient?

Energy Technology Data Exchange (ETDEWEB)

Narayan, Paresh Kumar; Zheng, Xinwei [School of Accounting, Economics and Finance, Faculty of Business and Law, Deakin University, 221 Burwood Highway, Burwood, Victoria 3125 (Australia); Narayan, Seema [School of Economics Finance and Marketing, RMIT University, Melbourne (Australia)

2010-10-15

In this paper we examine the long-run relationship between gold and oil spot and futures markets. We draw on the conceptual framework that when oil price rises, it creates inflationary pressures, which instigate investments in gold as a hedge against inflation. We test for the long-run relationship between gold and oil futures prices at different maturity and unravel evidence of cointegration. This implies that: (a) investors use the gold market as a hedge against inflation and (b) the oil market can be used to predict the gold market prices and vice versa, thus these two markets are jointly inefficient, at least for the sample period considered in this study. (author)

Gold and oil futures markets: Are markets efficient?

International Nuclear Information System (INIS)

Narayan, Paresh Kumar; Zheng, Xinwei; Narayan, Seema

2010-01-01

In this paper we examine the long-run relationship between gold and oil spot and futures markets. We draw on the conceptual framework that when oil price rises, it creates inflationary pressures, which instigate investments in gold as a hedge against inflation. We test for the long-run relationship between gold and oil futures prices at different maturity and unravel evidence of cointegration. This implies that: (a) investors use the gold market as a hedge against inflation and (b) the oil market can be used to predict the gold market prices and vice versa, thus these two markets are jointly inefficient, at least for the sample period considered in this study. (author)

Geoperspective | Oil and Gas in the Netherlands – Is there a future?

NARCIS (Netherlands)

Herber, R.; Jager, J. de

2010-01-01

The impact of oil and, in particular, gas fields discovered in the Dutch subsurface has been very significant. However, 50 years after the discovery of the giant Groningen gas field the Netherlands has become very mature for exploration of oil and gas, and the gas volume left to be discovered in

Modelling the petroleum generation and migration of the third member of the Shahejie Formation (Es3) in the Banqiao Depression of Bohai Bay Basin, Eastern China

Science.gov (United States)

Guo, Xiaowen; He, Sheng; Liu, Keyu; Shi, Zhongsheng; Bachir, Sani

2011-01-01

The mudstones in the third member of the Shahejie Formation (Es3) are the primary source rocks in the Banqiao Depression of Bohai Bay Basin. They are rich in organic matter with Total Organic Carbon (TOC) content up to 3.5%. The sandstones in the Es3 member are the deepest proven hydrocarbon reservoir rocks with measured porosity and permeability values ranging from 3.6% to 32.4% and from 0.01 md to 3283.7 md, respectively. One, two and three-dimensional basin modelling studies were performed to analyse the petroleum generation and migration history of the Es3 member in the Banqiao Depression based on the reconstruction of the burial, thermal and maturity history in order to evaluate the remaining potential of this petroleum province. The modelling results are calibrated with measured vitrinite reflectance ( R o), borehole temperatures and some drilling results of 63 wells in the study area. Calibration of the model with thermal maturity and borehole temperature data indicates that the present-day heat flow in the Banqiao Depression varies from 59.8 mW/m 2 to 61.7 mW/m 2 and the paleo-heat flow increased from 65 Ma to 50.4 Ma, reached a peak heat-flow values of approximately 75 mW/m 2 at 50.4 Ma and then decreased exponentially from 50.4 Ma to present-day. The source rocks of the Es3 member are presently in a stage of oil and condensate generation with maturity from 0.5% to 1.8% R o and had maturity from 0.5% to 1.25% R o at the end of the Dongying Formation (Ed) deposition (26 Ma). Oil generation (0.5% R o) in the Es3 member began from about 37 Ma to 34 Ma and the peak hydrocarbon generation (1.0% R o) occurred approximately from 30 Ma to 15 Ma. The modelled hydrocarbon expulsion evolution suggested that the timing of hydrocarbon expulsion from the Es3 member source rocks began from 31 Ma to 10 Ma with the peak hydrocarbon expulsion shortly after 26 Ma. Secondary petroleum migration pathways in the Es3 member of the Banqiao Depression are modelled based on the

Assessing field-scale biogeophysical signatures of bioremediation over a mature crude oil spill

Science.gov (United States)

Slater, Lee; Ntarlagiannis, Dimitrios; Atekwana, Estella; Mewafy, Farag; Revil, Andre; Skold, Magnus; Gorby, Yuri; Day-Lewis, Frederick D.; Lane, John W.; Trost, Jared J.; Werkema, Dale D.; Delin, Geoffrey N.; Herkelrath, William N.; Rectanus, H.V.; Sirabian, R.

2011-01-01

We conducted electrical geophysical measurements at the National Crude Oil Spill Fate and Natural Attenuation Research Site (Bemidji, MN). Borehole and surface self-potential measurements do not show evidence for the existence of a biogeobattery mechanism in response to the redox gradient resulting from biodegradation of oil. The relatively small self potentials recorded are instead consistent with an electrodiffusion mechanism driven by differences in the mobility of charge carriers associated with biodegradation byproducts. Complex resistivity measurements reveal elevated electrical conductivity and interfacial polarization at the water table where oil contamination is present, extending into the unsaturated zone. This finding implies that the effect of microbial cell growth/attachment, biofilm formation, and mineral weathering accompanying hydrocarbon biodegradation on complex interfacial conductivity imparts a sufficiently large electrical signal to be measured using field-scale geophysical techniques.

Organic tissues, graphite, and hydrocarbons in host rocks of the Rum Jungle Uranium Field, northern Australia

Science.gov (United States)

Foster, C.B.; Robbins, E.I.; Bone, Y.

1990-01-01

The Rum Jungle Uranium field consists of at least six early Proterozoic deposits that have been mined either for uranium and/or the associated base and precious metals. Organic matter in the host rocks of the Whites Formation and Coomalie Dolomite is now predominantly graphite, consistent with the metamorphic history of these rocks. For nine samples, the mean total organic carbon content is high (3.9 wt%) and ranged from 0.33 to 10.44 wt%. Palynological extracts from the host rocks include black, filamentous, stellate (Eoastrion-like), and spherical morphotypes, which are typical of early Proterozoic microbiota. The colour, abundance, and shapes of these morphotypes reflect the thermal history, organic richness, and probable lacustrine biofacies of the host rocks. Routine analysis of rock thin sections and of palynological residues shows that mineral grains in some of the host rocks are coated with graphitized organic matter. The grain coating is presumed to result from ultimate thermal degradation of a petroleum phase that existed prior to metamorphism. Hydrocarbons are, however, still present in fluid inclusions within carbonates of the Coomalie Dolomite and lower Whites Formation. The fluid inclusions fluoresce dull orange in blue-light excitation and their hydrocarbon content is confirmed by gas chromatography of whole-rock extracts. Preliminary analysis of the oil suggests that it is migrated, and because it has escaped graphitization through metamorphism it is probably not of early Proterozoic age. The presence of live oil is consistent with fluid inclusion data that suggest subsequent, low-temperature brine migration through the rocks. The present observations support earlier suggestions that organic matter in the host formations trapped uranium to form protore. Subsequent fluid migrations probably brought additional uranium and other metals to these formations, and the organic matter provided a reducing environment for entrapment. ?? 1990.

Revised models for hydrocarbon generation, migration and accumulation in Jurassic coal measures of the Turpan basin, NW China

Energy Technology Data Exchange (ETDEWEB)

Li Maowen; Stasiuk, L.D. [Geological Survey of Canada, Calgary, Alberta (Canada); Bao Jianping [Jianghan Petroleum University, Hubei (China); Lin, R. [Petroleum University (Beijing), Changping (China); Yuan Mingsheng [PetroChina Tu-Ha Oilfield Company, Xingjiang (China)

2001-07-01

Whether or not the Lower-Middle Jurassic coal measures in the Turpan basin of NW China have generated commercial quantities of liquid petroleums is a problem of considerable importance that remains contentious as it has not yet been resolved unequivocally. This study provides evidence against the Jurassic humic coals as the only major source for the oils discovered in the Taibei depression of this basin and suggests additional significant contributions from the Upper Permian and Middle-Lower Jurassic lacustrine source rocks. The Carboniferous-Permian marine source rocks may have been important also in limited locations along the major basement faults. Molecular and petrographic data indicate that the majority of the Middle Jurassic strata are currently immature or marginally mature with respect to hydrocarbon generation. Within the major depocenters, the Middle-Lower Jurassic coal-bearing strata of the Baodaowan and Xishanyao formations has reached the conventional oil window (i.e. with vitrinite reflectance >0.7 per cent Ro). Pre-Jurassic (Upper Permian in particular) derived hydrocarbons appear to be widespread in extracts of fractured Jurassic coal and fine-grained rocks. Large differences have been observed in the absolute concentrations of biomarker compounds in rock extracts of various source intervals. Thus, 'coaly' biomarker signatures of the oils most likely resulted from mixing and migration contamination when hydrocarbons derived from mature source rocks migrated up through highly fractured coal seams along deep-seated faults. In addition to conventional exploration targets, revised petroleum generation and accumulation models predict that the focus in the Turpan basin should also include deep structures within the Carboniferous-Permian strata and subtle, low magnitude anticlines and stratigraphic traps within thr Triassic-Jurassic sections. (author)

Molecular diversity of bacterial communities from subseafloor rock samples in a deep-water production basin in Brazil.

Science.gov (United States)

von der Weid, Irene; Korenblum, Elisa; Jurelevicius, Diogo; Rosado, Alexandre Soares; Dino, Rodolfo; Sebastian, Gina Vasquez; Seldin, Lucy

2008-01-01

The deep subseafloor rock in oil reservoirs represents a unique environment in which a high oilcontamination and very low biomass can be observed. Sampling this environment has been a challenge owing to the techniques used for drilling and coring. In this study, the facilities developed by the Brazilian oil company PETROBRAS for accessing deep subsurface oil reservoirs were used to obtain rock samples at 2,822-2,828 m below the ocean floor surface from a virgin field located in the Atlantic Ocean, Rio de Janeiro. To address the bacterial diversity of these rock samples, PCR amplicons were obtained using the DNA from four core sections and universal primers for 16S rRNA and for APS reductase (aps) genes. Clone libraries were generated from these PCR fragments and 87 clones were sequenced. The phylogenetic analyses of the 16S rDNA clone libraries showed a wide distribution of types in the domain bacteria in the four core samples, and the majority of the clones were identified as belonging to Betaproteobacteria. The sulfate-reducing bacteria community could only be amplified by PCR in one sample, and all clones were identified as belonging to Gammaproteobacteria. For the first time, the bacterial community was assessed in such deep subsurface environment.

Effect of organic matter properties, clay mineral type and thermal maturity on gas adsorption in organic-rich shale systems

Science.gov (United States)

Zhang, Tongwei; Ellis, Geoffrey S.; Ruppel, Stephen C.; Milliken, Kitty; Lewan, Mike; Sun, Xun; Baez, Luis; Beeney, Ken; Sonnenberg, Steve

2013-01-01

A series of CH4 adsorption experiments on natural organic-rich shales, isolated kerogen, clay-rich rocks, and artificially matured Woodford Shale samples were conducted under dry conditions. Our results indicate that physisorption is a dominant process for CH4 sorption, both on organic-rich shales and clay minerals. The Brunauer–Emmett–Teller (BET) surface area of the investigated samples is linearly correlated with the CH4 sorption capacity in both organic-rich shales and clay-rich rocks. The presence of organic matter is a primary control on gas adsorption in shale-gas systems, and the gas-sorption capacity is determined by total organic carbon (TOC) content, organic-matter type, and thermal maturity. A large number of nanopores, in the 2–50 nm size range, were created during organic-matter thermal decomposition, and they significantly contributed to the surface area. Consequently, methane-sorption capacity increases with increasing thermal maturity due to the presence of nanopores produced during organic-matter decomposition. Furthermore, CH4 sorption on clay minerals is mainly controlled by the type of clay mineral present. In terms of relative CH4 sorption capacity: montmorillonite ≫ illite – smectite mixed layer > kaolinite > chlorite > illite. The effect of rock properties (organic matter content, type, maturity, and clay minerals) on CH4 adsorption can be quantified with the heat of adsorption and the standard entropy, which are determined from adsorption isotherms at different temperatures. For clay-mineral rich rocks, the heat of adsorption (q) ranges from 9.4 to 16.6 kJ/mol. These values are considerably smaller than those for CH4 adsorption on kerogen (21.9–28 kJ/mol) and organic-rich shales (15.1–18.4 kJ/mol). The standard entropy (Δs°) ranges from -64.8 to -79.5 J/mol/K for clay minerals, -68.1 to -111.3 J/mol/K for kerogen, and -76.0 to -84.6 J/mol/K for organic-rich shales. The affinity of CH4 molecules for sorption on organic matter

Oil Contact Angles in a Water-Decane-Silicon Dioxide System: Effects of Surface Charge.

Science.gov (United States)

Xu, Shijing; Wang, Jingyao; Wu, Jiazhong; Liu, Qingjie; Sun, Chengzhen; Bai, Bofeng

2018-04-19

Oil wettability in the water-oil-rock systems is very sensitive to the evolution of surface charges on the rock surfaces induced by the adsorption of ions and other chemical agents in water flooding. Through a set of large-scale molecular dynamics simulations, we reveal the effects of surface charge on the oil contact angles in an ideal water-decane-silicon dioxide system. The results show that the contact angles of oil nano-droplets have a great dependence on the surface charges. As the surface charge density exceeds a critical value of 0.992 e/nm 2 , the contact angle reaches up to 78.8° and the water-wet state is very apparent. The variation of contact angles can be confirmed from the number density distributions of oil molecules. With increasing the surface charge density, the adsorption of oil molecules weakens and the contact areas between nano-droplets and silicon dioxide surface are reduced. In addition, the number density distributions, RDF distributions, and molecular orientations indicate that the oil molecules are adsorbed on the silicon dioxide surface layer-by-layer with an orientation parallel to the surface. However, the layered structure of oil molecules near the silicon dioxide surface becomes more and more obscure at higher surface charge densities.

Shale Gas and Oil in Germany - Resources and Environmental Impacts

Science.gov (United States)

Ladage, Stefan; Blumenberg, Martin; Houben, Georg; Pfunt, Helena; Gestermann, Nicolai; Franke, Dieter; Erbacher, Jochen

2017-04-01

In light of the controversial debate on "unconventional" oil and gas resources and the environmental impacts of "fracking", the Federal Institute for Geosciences and Natural Resources (BGR) conducted a comprehensive resource assessment of shale gas and light tight oil in Germany and studied the potential environmental impacts of shale gas development and hydraulic fracturing from a geoscientific perspective. Here, we present our final results (BGR 2016), incorporating the majority of potential shale source rock formations in Germany. Besides shale gas, light tight oil has been assessed. According to our set of criteria - i.e. thermal maturity 0.6-1.2 %vitrinite reflectance (VR; oil) and >1.2 % VR (gas) respectively, organic carbon content > 2%, depth between 500/1000 m and 5000 m as well as a net thickness >20 m - seven potentially generative shale formations were indentified, the most important of them being the Lower Jurassic (Toarcian) Posidonia shale with both shale gas and tight oil potential. The North German basin is by far the most prolific basin. The resource assessment was carried out using a volumetric in-place approach. Variability inherent in the input parameters was accounted for using Monte-Carlo simulations. Technically recoverable resources (TRR) were estimated using recent, production-based recovery factors of North American shale plays and also employing Monte-Carlo simulations. In total, shale gas TRR range between 320 and 2030 bcm and tight oil TRR between 13 and 164 Mio. t in Germany. Tight oil potential is therefore considered minor, whereas the shale gas potential exceeds that of conventional resources by far. Furthermore an overview of numerical transport modelling approaches concerning environmental impacts of the hydraulic fracturing is given. These simulations are based on a representative lithostratigraphy model of the North-German basin, where major shale plays can be expected. Numerical hydrogeological modelling of frac fluid

Rho-GTPase effector ROCK phosphorylates cofilin in actin-meditated cytokinesis during mouse oocyte meiosis.

Science.gov (United States)

Duan, Xing; Liu, Jun; Dai, Xiao-Xin; Liu, Hong-Lin; Cui, Xiang-Shun; Kim, Nam-Hyung; Wang, Zhen-Bo; Wang, Qiang; Sun, Shao-Chen

2014-02-01

During oocyte meiosis, a spindle forms in the central cytoplasm and migrates to the cortex. Subsequently, the oocyte extrudes a small body and forms a highly polarized egg; this process is regulated primarily by actin. ROCK is a Rho-GTPase effector that is involved in various cellular functions, such as stress fiber formation, cell migration, tumor cell invasion, and cell motility. In this study, we investigated possible roles for ROCK in mouse oocyte meiosis. ROCK was localized around spindles after germinal vesicle breakdown and was colocalized with cytoplasmic actin and mitochondria. Disrupting ROCK activity by RNAi or an inhibitor resulted in cell cycle progression and polar body extrusion failure. Time-lapse microscopy showed that this may have been due to spindle migration and cytokinesis defects, as chromosomes segregated but failed to extrude a polar body and then realigned. Actin expression at oocyte membranes and in cytoplasm was significantly decreased after these treatments. Actin caps were also disrupted, which was confirmed by a failure to form cortical granule-free domains. The mitochondrial distribution was also disrupted, which indicated that mitochondria were involved in the ROCK-mediated actin assembly. In addition, the phosphorylation levels of Cofilin, a downstream molecule of ROCK, decreased after disrupting ROCK activity. Thus, our results indicated that a ROCK-Cofilin-actin pathway regulated meiotic spindle migration and cytokinesis during mouse oocyte maturation.

Natural (13) C distribution in oil palm (Elaeis guineensis Jacq.) and consequences for allocation pattern.

Science.gov (United States)

Lamade, Emmanuelle; Tcherkez, Guillaume; Darlan, Nuzul Hijri; Rodrigues, Rosario Lobato; Fresneau, Chantal; Mauve, Caroline; Lamothe-Sibold, Marlène; Sketriené, Diana; Ghashghaie, Jaleh

2016-01-01

Oil palm has now become one of the most important crops, palm oil representing nearly 25% of global plant oil consumption. Many studies have thus addressed oil palm ecophysiology and photosynthesis-based models of carbon allocation have been used. However, there is a lack of experimental data on carbon fixation and redistribution within palm trees, and important C-sinks have not been fully characterized yet. Here, we carried out extensive measurement of natural (13) C-abundance (δ(13) C) in oil palm tissues, including fruits at different maturation stages. We find a (13) C-enrichment in heterotrophic organs compared to mature leaves, with roots being the most (13) C-enriched. The δ(13) C in fruits decreased during maturation, reflecting the accumulation in (13) C-depleted lipids. We further used observed δ(13) C values to compute plausible carbon fluxes using a steady-state model of (13) C-distribution including metabolic isotope effects ((12) v/(13) v). The results suggest that fruits represent a major respiratory loss (≈39% of total tree respiration) and that sink organs such as fruits are fed by sucrose from leaves. That is, glucose appears to be a quantitatively important compound in palm tissues, but computations indicate that it is involved in dynamic starch metabolism rather that C-exchange between organs. © 2015 John Wiley & Sons Ltd.

Selection and application of microorganisms to improve oil recovery

Energy Technology Data Exchange (ETDEWEB)

Almeida, P.F.; Moreira, R.S.; Almeida, R.C.C.; Guimaraes, A.K.; Carvalho, A.S. [Laboratorio de Biotecnologia e Ecologia de Microrganismos da Universidade Federal da Bahia, Avenida Reitor Miguel Calmon, s/n, Vale do Canela, CEP 41.160-100 Salvador BA (Brazil); Quintella, C.; Esperidia, M.C.A. [Instituto de Quimica da Universidade Federal da Bahia, Rua Barao de Geremoabo, s/n, Campus Universitario de Ondina, CEP 40.170-290, Salvador BA (Brazil); Taft, C.A. [Centro Brasileiro de Pesquisas Fisicas, Rua Xavier Sigaud, 150, Urca, 22290-180, Rio de Janeiro (Brazil)

2004-08-01

Microbial enhanced oil recovery (Meor) is an incontestably efficient alternative to improve oil recovery, especially in mature fields and in oil reservoirs with high paraffinic content. This is the case for most oil fields in the Reconcavo basin of Bahia, Brazil. Given the diverse conditions of most oil fields, an approach to apply Meor technology should consider primarily: (i) microbiological studies to select the appropriate microorganisms and (ii) mobilization of oil in laboratory experiments before oil field application. A total of 163 bacterial strains, selectively isolated from various sources, were studied to determine their potential to be used in Meor. A laboratory microbial screening based on physiological and metabolic profiles and growth rates under conditions representative for oil fields and reservoirs revealed that 10 bacterial strains identified as Pseudomonas aeruginosa (2), Bacillus licheniformis (2), Bacillus brevis (1), Bacillus polymyxa (1), Micrococcus varians (1), Micrococcus sp. (1), and two Vibrio species demonstrated potential to be used in oil recovery. Strains of B. licheniformis and B. polymyxa produced the most active surfactants and proved to be the most anaerobic and thermotolerant among the selected bacteria. Micrococcus and B. brevis were the most salt-tolerant and polymer producing bacteria, respectively, whereas Vibrio sp. and B. polymyxa strains were the most gas-producing bacteria. Three bacterial consortia were prepared with a mixture of bacteria that showed metabolic and technological complementarity and the ability to grow at a wide range of temperatures and salinity characteristics for the oil fields in Bahia, Brazil. Oil mobilization rates in laboratory column experiments using the three consortia of bacteria varied from 11.2 to 18.3 % [v/v] of the total oil under static conditions. Consortia of B. brevis, B. icheniformis and B. polymyxa exhibited the best oil mobilization rates. Using these consortia under anaerobic

Artificial intelligence applications in offshore oil and gas production

International Nuclear Information System (INIS)

Attia, F.G.

1994-01-01

The field of Artificial Intelligence (AI) has gained considerable acceptance in virtually all fields, of engineering applications. Artificial intelligence is now being applied in several areas of offshore oil and gas operations, such as drilling, well testing, well logging and interpretation, reservoir engineering, planning and economic evaluation, process control, and risk analysis. Current AI techniques offer a new and exciting technology for solving problems in the oil and gas industry. Expert systems, fuzzy logic systems, neural networks and genetic algorithms are major AI technologies which have made an impact on the petroleum industry. Presently, these technologies are at different stages of maturity with expert systems being the most mature and genetic algorithms the least. However, all four technologies have evolved such that practical applications were produced. This paper describes the four major Al techniques and their many applications in offshore oil and gas production operations. A summary description of future developments in Al technology that will affect the execution and productivity of offshore operations will be also provided

Structural Analysis: Folds Classification of metasedimentary rock in the Peninsular Malaysia

Science.gov (United States)

Shamsuddin, A.

2017-10-01

Understanding shear zone characteristics of deformation are a crucial part in the oil and gas industry as it might increase the knowledge of the fracture characteristics and lead to the prediction of the location of fracture zones or fracture swarms. This zone might give high influence on reservoir performance. There are four general types of shear zones which are brittle, ductile, semibrittle and brittle-ductile transition zones. The objective of this study is to study and observe the structural geometry of the shear zones and its implication as there is a lack of understanding, especially in the subsurface area because of the limitation of seismic resolution. A field study was conducted on the metasedimentary rocks (shear zone) which are exposed along the coastal part of the Peninsular Malaysia as this type of rock resembles the types of rock in the subsurface. The analysis in this area shows three main types of rock which are non-foliated metaquartzite and foliated rock which can be divided into slate and phyllite. Two different fold classification can be determined in this study. Layer 1 with phyllite as the main type of rock can be classified in class 1C and layer 2 with slate as the main type of rock can be classified in class 1A. This study will benefit in predicting the characteristics of the fracture and fracture zones.

On the feasibility of inducing oil mobilization in existing reservoirs via wellbore harmonic fluid action

KAUST Repository

Jeong, Chanseok; Huh, Chun; Kallivokas, Loukas F.

2011-01-01

Although vibration-based mobilization of oil remaining in mature reservoirs is a promising low-cost method of enhanced oil recovery (EOR), research on its applicability at the reservoir scale is still at an early stage. In this paper, we use

Distribution and evolution of Zn, Cd, and Pb in Apollo 16 regolith samples and the average U-Pb ages of the parent rocks

Science.gov (United States)

Cirlin, E. H.; Housley, R. M.

1982-01-01

The concentration of surface (low temperature site) and interior (high temperature site) Cd, Zn, and Pb in 13 Apollo 16 highland fines samples, pristine rock 65325, and mare fines sample 75081 were analyzed directly from the thermal release profiles obtained by flameless atomic absorption technique (FLAA). Cd and Zn in pristine ferroan anothosite 65325, anorthositic grains of the most mature fines 65701, and basaltic rock fragments of mare fines 75081 were almost all surface Cd and Zn indicating that most volatiles were deposited on the surfaces of vugs, vesicles and microcracks during the initial cooling process. A considerable amount of interior Cd and Zn was observed in agglutinates. This result suggests that high temperature site interior volatiles originate from entrapment during the lunar maturation processes. Interior Cd found in the most mature fines sample 65701 was only about 15% of the total Cd in the sample. Interior Pb present in Apollo 16 fines samples went up to 60%. From our Cd studies we can assume that this interior Pb in highland fines samples is largely due to the radiogenic decay which occurred after the redistribution of the volatiles took place. We obtained an average age of 4.0 b.y. for the parent rocks of Apollo 16 highland regolith from our interior Pb analyses.

Water - rock interaction in different rock environments

International Nuclear Information System (INIS)

Lamminen, S.

1995-01-01

The study assesses the groundwater geochemistry and geological environment of 44 study sites for radioactive waste disposal. Initially, the study sites were divided by rock type into 5 groups: (1) acid - intermediate rocks, (2) mafic - ultramafic rocks, (3) gabbros, amphibolites and gneisses that contain calc-silicate (skarn) rocks, (4) carbonates and (5) sandstones. Separate assessments are made of acid - intermediate plutonic rocks and of a subgroup that comprises migmatites, granite and mica gneiss. These all belong to the group of acid - intermediate rocks. Within the mafic -ultramafic rock group, a subgroup that comprises mafic - ultramafic plutonic rocks, serpentinites, mafic - ultramafic volcanic rocks and volcanic - sedimentary schists is also evaluated separately. Bedrock groundwaters are classified by their concentration of total dissolved solids as fresh, brackish, saline, strongly saline and brine-class groundwaters. (75 refs., 24 figs., 3 tabs.)

Salinity-dependent contact angle alteration in oil/brine/silicate systems : The effect of temperature