Topical study on IRS events involving foreign material intrusion in plant systems. First issue. Report of a consultants meeting. Working material

International Nuclear Information System (INIS)

1997-01-01

Recent exchange of operational safety experience among countries, within the framework of the IRS, revealed a noticeable increase in incidents involving foreign material intrusion (FMI) in nuclear power plant systems. These incidents appeared to have safety impact, sometimes widespread, on many systems and components, including the reactor core, control rods, the secondary side, and other support systems such as the electrical, air, and water systems. Notwithstanding the economic penalties and the operational problems that can arise from the FMI, many events indicated severe component damages, challenges to safety systems and to fuel integrity. Difficulties encountered with the removal of foreign material present further challenges due to the long term effects of such material remaining in the system and interacting with either fuel cladding, with the potential of releasing fission products in coolant systems, or with the system pressure boundary with the potential for material wear and sudden failure of the pressure boundary. The FMI topic was, therefore, one of a number of topics that was recommended by the TCM in 1996 for investigation. A consultant meeting was held at the IAEA during the period 14-18 April 1997 to address this topic. Figs

The environmental suitability of industrial secondary products used as covering materials in landfills

International Nuclear Information System (INIS)

Laine-Ylijoki, J.; Wahlstroem, M.; Maekelae, E.

2001-01-01

The industrial secondary products and landmasses polluted in a minor way can be used as coverings and sealing materials and also restricted in the ground construction of landfills. By using suitable secondary products, natural materials can be reduced. Substitutes are needed due to the fact that the availability of natural materials is poor in many areas. The presented project is a part of the Streams technology programme financed by Tekes. It includes the development of the measuring methods to study the environmental suitability of industrial secondary products, which will be used as covering materials of landfills. Based on the results, a handbook addressing the environmental suitability procedure will be compiled

Evaluation of the odour reduction potential of alternative cover materials at a commercial landfill.

Science.gov (United States)

Solan, P J; Dodd, V A; Curran, T P

2010-02-01

The availability of virgin soils and traditional landfill covers are not only costly and increasingly becoming scarce, but they also reduce the storage capacity of landfill. The problem can be overcome by the utilisation of certain suitable waste streams as alternative landfill covers. The objective of this study was to assess the suitability of Construction & Demolition fines (C&D), Commercial & Industrial fines (C&I) and woodchip (WC) as potential landfill cover materials in terms of odour control. Background odour analysis was conducted to determine if any residual odour was emitted from the cover types. It was deemed negligible for the three materials. The odour reduction performance of each of the materials was also examined on an area of an active landfill site. A range of intermediate cover compositions were also studied to assess their performance. Odour emissions were sampled using a Jiang hood and analysed. Results indicate that the 200 mm deep combination layer of C&D and wood chip used on-site is adequate for odour abatement. The application of daily cover was found to result in effective reduction allowing for the background odour of woodchip.

Computational Nanotechnology Molecular Electronics, Materials and Machines

Science.gov (United States)

Srivastava, Deepak; Biegel, Bryan A. (Technical Monitor)

2002-01-01

This presentation covers research being performed on computational nanotechnology, carbon nanotubes and fullerenes at the NASA Ames Research Center. Topics cover include: nanomechanics of nanomaterials, nanotubes and composite materials, molecular electronics with nanotube junctions, kinky chemistry, and nanotechnology for solid-state quantum computers using fullerenes.

NATO Advanced Research Workshop on New Materials for Thermoelectric Applications

CERN Document Server

Hewson, Alex

2013-01-01

Thermoelectric devices could play an important role in making efficient use of our energy resources but their efficiency would need to be increased for their wide scale application. There is a multidisciplinary search for materials with an enhanced thermoelectric responses for use in such devices. This volume covers the latest ideas and developments in this research field, covering topics ranging from the fabrication and characterization of new materials, particularly those with strong electron correlation, use of nanostructured, layered materials and composites, through to theoretical work to gain a deeper understanding of thermoelectric behavior. It should be a useful guide and stimulus to all working in this very topical field.

Proceedings of the first topical meeting on Asian network for accelerator-driven systems and nuclear transmutation technology

International Nuclear Information System (INIS)

Sasa, Toshinobu

2016-03-01

The first topical meeting on Asian Network for Accelerator-driven System (ADS) and Nuclear Transmutation Technology (NTT) was held on 26-27 October 2015 at the J-PARC Center, Japan Atomic Energy Agency, Japan. The topical meeting was an optional one in-between the regular meeting, which is held in every two years. Instead of the regular meetings, which cover all research fields for ADS and NTT, such as accelerator, spallation target, subcritical reactor, fuel, and material, the topical meeting is focused on a specific topic to make technical discussions more deeply. In this meeting, the technology for lead-bismuth eutectic alloy was selected, as it was one of the hot issues in the world, and the topic was deeply discussed by specialists in Asian countries. This report summarizes all presentation materials discussed in the meeting. (author)

Evapotranspiration (ET) covers.

Science.gov (United States)

Rock, Steve; Myers, Bill; Fiedler, Linda

2012-01-01

Evapotranspiration (ET) cover systems are increasingly being used at municipal solid waste (MSW) landfills, hazardous waste landfills, at industrial monofills, and at mine sites. Conventional cover systems use materials with low hydraulic permeability (barrier layers) to minimize the downward migration of water from the surface to the waste (percolation), ET cover systems use water balance components to minimize percolation. These cover systems rely on soil to capture and store precipitation until it is either transpired through vegetation or evaporated from the soil surface. Compared to conventional membrane or compacted clay cover systems, ET cover systems are expected to cost less to construct. They are often aesthetic because they employ naturalized vegetation, require less maintenance once the vegetative system is established, including eliminating mowing, and may require fewer repairs than a barrier system. All cover systems should consider the goals of the cover in terms of protectiveness, including the pathways of risk from contained material, the lifecycle of the containment system. The containment system needs to be protective of direct contact of people and animals with the waste, prevent surface and groundwater water pollution, and minimize release of airborne contaminants. While most containment strategies have been based on the dry tomb strategy of keeping waste dry, there are some sites where adding or allowing moisture to help decompose organic waste is the current plan. ET covers may work well in places where complete exclusion of precipitation is not needed. The U.S. EPA Alternative Cover Assessment Program (ACAP), USDOE, the Nuclear Regulatory Commission, and others have researched ET cover design and efficacy, including the history of their use, general considerations in their design, performance, monitoring, cost, current status, limitations on their use, and project specific examples. An on-line database has been developed with information

Selected Topics in MicroNano-robotics for Biomedical Applications

CERN Document Server

2013-01-01

Selected Topics in Micro/Nano-robotics for Biomedical Applications features a system approach and incorporates modern methodologies in autonomous mobile robots for programmable and controllable micro/nano-robots aiming at biomedical applications. The book provides chapters of instructional materials and cutting-edge research results in micro/nanorobotics for biomedical applications. The book presents new sensing technology on nanofibers, new power supply techniques including miniature fuel cells and energy harvesting devices, and manipulation techniques including AFM-based nano-robotic manipulation, robot-aided optical tweezers, and robot-assisted catheter surgery systems. It also contains case studies on using micro/nano-robots in biomedical environments and in biomedicine, as well as a design example to conceptually develop a Vitamin-pill sized robot to enter human’s gastrointestinal tract. Each chapter covers a different topic of the highly interdisciplinary area. Bring together the selected topics into ...

INSTRUCTIONAL MATERIALS CATALOG.

Science.gov (United States)

Ohio Vocational Agriculture Instructional Materials Service, Columbus.

THE TITLE, IDENTIFICATION NUMBER, DATE OF PUBLICATION, PAGINATION, A BRIEF DESCRIPTION, AND PRICE ARE GIVEN FOR EACH OF THE INSTRUCTIONAL MATERIALS AND AUDIOVISUAL AIDS INCLUDED IN THIS CATALOG. TOPICS COVERED ARE FIELD CORPS, HORTICULTURE, ANIMAL SCIENCE, SOILS, AGRICULTURAL ENGINEERING, AND FARMING PROGRAMS. AN ORDER FORM IS INCLUDED. (JM)

Advanced topics in the arithmetic of elliptic curves

CERN Document Server

Silverman, Joseph H

1994-01-01

In the introduction to the first volume of The Arithmetic of Elliptic Curves (Springer-Verlag, 1986), I observed that "the theory of elliptic curves is rich, varied, and amazingly vast," and as a consequence, "many important topics had to be omitted." I included a brief introduction to ten additional topics as an appendix to the first volume, with the tacit understanding that eventually there might be a second volume containing the details. You are now holding that second volume. it turned out that even those ten topics would not fit Unfortunately, into a single book, so I was forced to make some choices. The following material is covered in this book: I. Elliptic and modular functions for the full modular group. II. Elliptic curves with complex multiplication. III. Elliptic surfaces and specialization theorems. IV. Neron models, Kodaira-Neron classification of special fibers, Tate's algorithm, and Ogg's conductor-discriminant formula. V. Tate's theory of q-curves over p-adic fields. VI. Neron's theory of can...

Strategic raw materials. Risk management

International Nuclear Information System (INIS)

Bertau, Martin; Matschullat, Joerg; Kausch, Peter

2014-01-01

This volume is divided into four chapters: (1) Raw material management, (2) Primary raw materials, (3) Secondary raw materials and recycling, (4). Processing and products. The topics for the chapter ''Raw material management'' are: Substitution of raw materials - framework conditions and implementation; Thales: Strategic raw materials; Time for cooperation between the EU and China in raw materials policy; Availability of elements for the semiconductor industry; Market price risks of raw material-intensive companies - identification and management. The topics on the second item ''Primary raw materials'' are: The supply of economic-critical raw materials - A search and analysis for causes; Lithium extraction from primary raw materials - state and perspectives; The global market of rare earths - A balancing act; Rare earth deposits in Namibia; New technologies in exploration and discovery - Focus on activities in Europe. The third chapter, ''Secondary Raw Materials and Recycling'', covered the topics: Technology metals - Systemic Requirements along the recycling chain; Integrated re-use of high-tech and greentech wastes; From the sewage sludge ash to the phosphorus fertilizer RecoPhos P38 in the stress field of waste, fertilizer and soil protection. In chapter 4. ''Processing and products'' are the topics: Treatment and processing of rare earth metals; Processing of mineral resources - opportunities and challenges; Consequences of modern germanium chemistry; Strategic resources - Risk management. A review and outlook with a pinch of fantasy.. [de

Standard Practice for Exposure of Solar Collector Cover Materials to Natural Weathering Under Conditions Simulating Stagnation Mode

CERN Document Server

American Society for Testing and Materials. Philadelphia

1992-01-01

1.1 This practice covers a procedure for the exposure of solar collector cover materials to the natural weather environment at elevated temperatures that approximate stagnation conditions in solar collectors having a combined back and edge loss coefficient of less than 1.5 W/(m2 · °C). 1.2 This practice is suitable for exposure of both glass and plastic solar collector cover materials. Provisions are made for exposure of single and double cover assemblies to accommodate the need for exposure of both inner and outer solar collector cover materials. 1.3 This practice does not apply to cover materials for evacuated collectors, photovoltaic cells, flat-plate collectors having a combined back and edge loss coefficient greater than 1.5 W/(m2 ·° C), or flat-plate collectors whose design incorporates means for limiting temperatures during stagnation. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard t...

Selected topics in special nuclear materials safeguard system design

International Nuclear Information System (INIS)

King, L.L.; Thatcher, C.D.; Clarke, J.D.; Rodriguez, M.P.

1991-01-01

During the past two decades the improvements in circuit integration have given rise to many new applications in digital processing technology by continuously reducing the unit cost of processing power. Along with this increase in processing power a corresponding decrease in circuit volume has been achieved. Progress has been so swift that new classes of applications become feasible every 2 or 3 years. This is especially true in the application of proven new technology to special nuclear materials (SNM) safeguard systems. Several areas of application were investigated in establishing the performance requirements for the SNM safeguard system. These included the improvements in material control and accountability and surveillance by using multiple sensors to continuously monitor SNM inventory within the selected value(s); establishing a system architecture to provide capabilities needed for present and future performance requirements; and limiting operating manpower exposure to radiation. This paper describes two selected topics in the application of state-of-the-art, well-proven technology to SNM safeguard system design

Advances in electronic materials

CERN Document Server

Kasper, Erich; Grimmeiss, Hermann G

2008-01-01

This special-topic volume, Advances in Electronic Materials, covers various fields of materials research such as silicon, silicon-germanium hetero-structures, high-k materials, III-V semiconductor alloys and organic materials, as well as nano-structures for spintronics and photovoltaics. It begins with a brief summary of the formative years of microelectronics; now the keystone of information technology. The latter remains one of the most important global technologies, and is an extremely complex subject-area. Although electronic materials are primarily associated with computers, the internet

Materials research in AECL, Spring 1970

Energy Technology Data Exchange (ETDEWEB)

NONE

1970-05-15

This report gives a summary of materials research at Atomic Energy of Canada Limited. The topics covered in this report include engineering design with brittle materials, texture and mechanical properties of zirconium alloy tubing, structural damage by ion bombardment, research on silicon carbide, shallow phosphorus diffusion in p-type silicon and scanning electron microscopy. CRNL facilities for the examination of irradiated materials is also discussed.

Materials research in AECL, Spring 1970

International Nuclear Information System (INIS)

1970-05-01

This report gives a summary of materials research at Atomic Energy of Canada Limited. The topics covered in this report include engineering design with brittle materials, texture and mechanical properties of zirconium alloy tubing, structural damage by ion bombardment, research on silicon carbide, shallow phosphorus diffusion in p-type silicon and scanning electron microscopy. CRNL facilities for the examination of irradiated materials is also discussed

EM wave propagation analysis in plasma covered radar absorbing material

CERN Document Server

Singh, Hema; Rawat, Harish Singh

2017-01-01

This book focuses on EM propagation characteristics within multilayered plasma-dielectric-metallic media. The method used for analysis is impedance transformation method. Plasma covered radar absorbing material is approximated as a multi-layered dielectric medium. The plasma is considered to be bounded homogeneous/inhomogeneous medium. The reflection coefficient and hence return loss is analytically derived. The role of plasma parameters, such as electron density, collision frequency, plasma thickness, and plasma density profile in the absorption behavior of multi-layered plasma-RAM structure is described. This book provides a clearer picture of EM propagation within plasma. The reader will get an insight of plasma parameters that play significant role in deciding the absorption characteristics of plasma covered surfaces.

Land use and cover change as an overarching topic in the Dutch National Research Programme on Global Air Pollution and Climate Change : issues for implementation

NARCIS (Netherlands)

Fresco, L.O.; Berg, van den M.M.; Zeijl-Rozema, van A.E.

1996-01-01

The integration study 'Land Use and Cover Change as an overarching topic in the Dutch National Research Programme on Global Air Pollution and Climate Change (NRP)' aims at identifying research fields in which the NRP can contribute most effectively to the international scientific

EXAMINING COMFORT PROPERTIES OF LEATHER and ARTIFICIAL LEATHER COVER MATERIALS

Directory of Open Access Journals (Sweden)

ÇETİN Münire Sibel

2016-05-01

Full Text Available The analysis and regulation of workplace, working instruments, the comfort of office chair, business environment (sound, lighting, climate, vibration, temperature, and humidity, work and break times, analysis and editing of the organization, are some of the topics of interest of ergonomics. Environmental impact and conditions have important role on the employee’s working comfortably and efficiently. Therefore these conditions need to be aligned to the human body nature. Unsuitable working conditions (noise, etc. cause additional load, which the human body endures, and this additional load reveals the signs of tiredness in the body. Even an office environment, unsuitable physical environment impairs health of workers and reduces the performance. Therefore, office climate, environmental factors such as lighting and noise must be harmonized with the employee’s body nature in all working environments. Seating comfort is one of the important factors affecting the performance of employees in the office environment. There are so many studies about chair dimensions and the disorders on human body which were caused by the inappropriate chair dimensions and sitting positions. However, there are a spot of studies about the surface of the chair and the discomfort caused by the chair cover and its negative performance effects. In this study, some results of seat cover analysis for the design of an ergonomic chair. Recently, ease of cleaning, low cost advantages caused the increasing of the use of artificial leather especially on the surface of the seat used in offices. The physical properties of natural leather and artificial leather were compared as the candidate covers to be used on the design of an ergonomic office chair.

Topics in industrial mathematics

International Nuclear Information System (INIS)

Vatsya, S.R.

1992-01-01

Mathematical methods are widely used to solve practical problems arising in modern industry. This article outlines some of the topics relevant to AECL programmes. This covers the applications of transmission and neutron transport tomography to determine density distributions in rocks and two phase flow situations. Another example covered is the use of variational methods to solve the problems of aerosol migration and control theory. (author). 7 refs

Standard Practice for Exposure of Cover Materials for Solar Collectors to Natural Weathering Under Conditions Simulating Operational Mode

CERN Document Server

American Society for Testing and Materials. Philadelphia

1995-01-01

1.1 This practice provides a procedure for the exposure of cover materials for flat-plate solar collectors to the natural weather environment at temperatures that are elevated to approximate operating conditions. 1.2 This practice is suitable for exposure of both glass and plastic solar collector cover materials. Provisions are made for exposure of single and double cover assemblies to accommodate the need for exposure of both inner and outer solar collector cover materials. 1.3 This practice does not apply to cover materials for evacuated collectors or photovoltaics. 1.4 The values stated in SI units are to be regarded as the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Materials accounting at Los Alamos National Laboratory

International Nuclear Information System (INIS)

Erkkila, B.H.; Roberts, N.J.

1989-01-01

This presentation gives an overview of the accounting system used at the Los Alamos National Laboratory by the Los Alamos Nuclear Material Accounting and Safeguards System (MASS). This system processes accounting data in real time for bulk materials, discrete items, and materials undergoing dynamic processing. The following topics are covered in this chapter: definitions; nuclear material storage; nuclear material storage; computer system; measurement control program; inventory differences; and current programs and future plans

Proceedings of microwave processing of materials 3

International Nuclear Information System (INIS)

Beatty, R.L.

1992-01-01

This book contains proceedings of the third MRS Symposium on Microwave Processing of Materials. Topics covered include: Microwave Processing Overviews, Numerical Modeling Techniques, Microwave Processing System Design, Microwave/Plasma Processing, Microwave/Materials Interactions, Microwave Processing of Ceramics, Microwave Processing of Polymers, Microwave Processing of Hazardous Wastes, Microwave NDE Techniques and Dielectric Properties and Measurements

Introduction to Special Edition (of the Journal of Nuclear Materials Management) on Reducing the Threat from Radioactive Materials

International Nuclear Information System (INIS)

Mladineo, Stephen V.

2007-01-01

Introductory article for special edition of the JOURNAL OF NUCLEAR MATERIALS MANAGEMENT outlining the Institute of Nuclear Materials Management Nonproliferation and Arms Control Technical Division. In particular the International Nuclear and Radiological Security Standing Committee and its initial focus covering four topical areas--Radiological Threat Reduction, Nuclear Smuggling and Illicit Trafficking, Countering Nuclear Terrorism, and Radiological Terrorism Consequence Management

Dosimetry methods for fuels, cladding and structural materials

International Nuclear Information System (INIS)

Roettger, H.

1980-01-01

This volume of the proceedings of the symposium on reactor dosimetry covers the following topics: the metallurgy and dosimetry interface, radiation damage correlations of structural materials and damage analyses techniques, dosimetry for fusion materials, light water reactor pressure vessel surveillance in practice and irradiation experiments, fast reactor and reseach reactor characterization

Basic concepts of materials accounting

International Nuclear Information System (INIS)

Markin, J.T.

1989-01-01

The importance of accounting for nuclear materials to the efficient, safe, and economical operation of nuclear facilities is introduced, and the following topics are covered: material balance equation; item control areas; material balance uncertainty; decision procedures for materials accounting; conventional and near-real-time accounting; regulatory requirements of the US Department of Energy and the Nuclear Regulatory Commission; and a summary related to the development of a materials accounting system to implement the basic concepts described. The summary includes a section on each of the following: problem definition, system objectives, and system design

Carbon The Future Material for Advanced Technology Applications

CERN Document Server

Messina, Giacomo

2006-01-01

Carbon-based materials and their applications constitute a burgeoning topic of scientific research among scientists and engineers attracted from diverse areas such as applied physics, materials science, biology, mechanics, electronics and engineering. Further development of current materials, advances in their applications, and discovery of new forms of carbon are the themes addressed by the frontier research in these fields. This book covers all the fundamental topics concerned with amorphous and crystalline C-based materials, such as diamond, diamond-like carbon, carbon alloys, carbon nanotubes. The goal is, by coherently progressing from growth - and characterisation techniques to technological applications for each class of material, to fashion the first comprehensive state-of-the-art review of this fast evolving field of research in carbon materials.

International conference on composite materials and energy: Proceedings. Enercomp 95

International Nuclear Information System (INIS)

Anon.

1995-01-01

World demand for composite materials is continuously increasing. High strength and rigidity, associated with light weight, are the key factors for composites' success. These materials find numerous applications in all sectors of industry. Presently, a sector of particular interest in terms of demand for composite materials is the energy industry. More and more applications are found in the field of the forms of energy: electrical, petroleum, gas, nuclear, solar and wind. The topics addressed in various sessions of the conference cover potential applications of the entire range of polymer, metal and ceramic composites in all sectors of energy. Papers are divided into sessions covering the following topics: properties; design and analysis; fracture; fatigue and long-term performance; new materials; innovative processing; liquid molding; joining and repairs; radiation curing; recycling; development in ceramic materials; innovations in metallic materials; metal-matrix composites; nondestructive evaluation; energy savings in transportation; pressure vessels and piping; wind energy applications; electrical components; concrete applications; power plant applications; and new materials in the energy field. Most of the papers have been processed separately for inclusion on the data base

Human-competitive automatic topic indexing

CERN Document Server

Medelyan, Olena

2009-01-01

Topic indexing is the task of identifying the main topics covered by a document. These are useful for many purposes: as subject headings in libraries, as keywords in academic publications and as tags on the web. Knowing a document’s topics helps people judge its relevance quickly. However, assigning topics manually is labor intensive. This thesis shows how to generate them automatically in a way that competes with human performance. Three kinds of indexing are investigated: term assignment, a task commonly performed by librarians, who select topics from a controlled vocabulary; tagging, a popular activity of web users, who choose topics freely; and a new method of keyphrase extraction, where topics are equated to Wikipedia article names. A general two-stage algorithm is introduced that first selects candidate topics and then ranks them by significance based on their properties. These properties draw on statistical, semantic, domain-specific and encyclopedic knowledge. They are combined using a machine learn...

Topics in lightwave transmission systems

CERN Document Server

Li, Tingye

1991-01-01

Topics in Lightwave Transmission Systems is a second volume of a treatise on optical fiber communications that is devoted to the science, engineering, and application of information transmission via optical fibers. The first volume, published in 1985, dealt exclusively with fiber fabrication. The present volume contains topics that pertain to subsystems and systems. The book contains five chapters and begins with discussions of transmitters and receivers, which are basic to systems now operating in the field. Subsequent chapters cover topics relating to coherent systems: frequency and phase m

Ocean waste disposal. A bibliography with abstracts. Search period covered 1964--May 1975

International Nuclear Information System (INIS)

1975-01-01

The majority of the cited topics discuss the ocean disposal of sewage, sewage sludge, and dredged material, although reports on the disposal of radioactive wastes, brines, and industrial wastes are also covered. The ecological effects are included, as is research on the pollution of the New York Bight. However, studies on the discharge of heated effluents is excluded. Contains 164 abstracts. (auth)

The effect of greenhouse covering materials on phytochemical composition and antioxidant capacity of tomato cultivars.

Science.gov (United States)

Ahmadi, Latifeh; Hao, Xiuming; Tsao, Rong

2018-02-13

The effect of light transmission (direct and diffuse) on the phenolic compounds of five tomato cultivars was investigated under controlled conditions in greenhouses covered with different covering materials. The type of covering material and type of diffusion of light simultaneously affected the reducing power of cultivars. Two-way analysis of variance showed statistically significant differences in total phenolic content for the different cultivars (P  0.05). This study showed that the use of solar energy transmission could positively affect the reducing power of cultivars and alter the biosynthesis of certain phytochemicals that are health-beneficial. Further study could lead to applications for producing greenhouse vegetables with greater health attributes. © 2018 Society of Chemical Industry. © 2018 Society of Chemical Industry.

Lecture Notes on Topics in Accelerator Physics

International Nuclear Information System (INIS)

Chao, Alex W.

2002-01-01

These are lecture notes that cover a selection of topics, some of them under current research, in accelerator physics. I try to derive the results from first principles, although the students are assumed to have an introductory knowledge of the basics. The topics covered are: (1) Panofsky-Wenzel and Planar Wake Theorems; (2) Echo Effect; (3) Crystalline Beam; (4) Fast Ion Instability; (5) Lawson-Woodward Theorem and Laser Acceleration in Free Space; (6) Spin Dynamics and Siberian Snakes; (7) Symplectic Approximation of Maps; (8) Truncated Power Series Algebra; and (9) Lie Algebra Technique for nonlinear Dynamics. The purpose of these lectures is not to elaborate, but to prepare the students so that they can do their own research. Each topic can be read independently of the others

Lecture Notes on Topics in Accelerator Physics

Energy Technology Data Exchange (ETDEWEB)

Chao, Alex W.

2002-11-15

These are lecture notes that cover a selection of topics, some of them under current research, in accelerator physics. I try to derive the results from first principles, although the students are assumed to have an introductory knowledge of the basics. The topics covered are: (1) Panofsky-Wenzel and Planar Wake Theorems; (2) Echo Effect; (3) Crystalline Beam; (4) Fast Ion Instability; (5) Lawson-Woodward Theorem and Laser Acceleration in Free Space; (6) Spin Dynamics and Siberian Snakes; (7) Symplectic Approximation of Maps; (8) Truncated Power Series Algebra; and (9) Lie Algebra Technique for nonlinear Dynamics. The purpose of these lectures is not to elaborate, but to prepare the students so that they can do their own research. Each topic can be read independently of the others.

Supercapacitors materials, systems and applications

CERN Document Server

Lu, Max; Frackowiak, Elzbieta

2013-01-01

Written by an international group of leading experts from both academia and industry, this is the first comprehensive book on the topic for 10 years. Taking into account the commercial interest in these systems and the scientific and technological developments over the past decade, all important materials and systems are covered, with several chapters devoted to topics of direct industrial relevance.The book starts by providing an introduction to the general principles of electrochemistry, the properties of electrochemical capacitors, and electrochemical characterization techniques. There

The Optical Society's 2016 topical meeting on optical interference coatings: introduction.

Science.gov (United States)

Ristau, Detlev; Li, Li; Sargent, Robert; Sytchkova, Anna

2017-02-01

This feature issue of Applied Optics is dedicated to the 13th Topical Meeting on Optical Interference Coatings, which was held June 19-24, 2016, in Tucson, Arizona, USA. The conference, taking place every three years, is a focal point for global technical interchange in the field of optical interference coatings and provides premier opportunities for people working in the field to present their new advances in research and development. Papers presented at the meeting covered a broad range of topics, including fundamental research on coating design theory, new materials, and deposition and characterization technologies, as well as the vast and growing number of applications in electronic displays, communication, optical instruments, high power and ultra-fast lasers, solar cells, space missions, gravitational wave detection, and many others.

Topics of Bioengineering in Wikipedia

Directory of Open Access Journals (Sweden)

Vassia Atanassova

2009-10-01

Full Text Available The present report aims to give a snapshot of how topics from the field of bioengineering (bioinformatics, bioprocess systems, biomedical engineering, biotechnology, etc. are currently covered in the free electronic encyclopedia Wikipedia. It also offers insights and information about what Wikipedia is, how it functions, how and when to cite Wikipedian articles, if necessary. Several external wikis, devoted to topics of bioengineering, are also listed and reviewed.

Selected Bibliography of Egyptian Educational Materials, Vol. 1, No. 3, 1975.

Science.gov (United States)

Al-Ahram Center for Scientific Translations, Cairo (Egypt).

There are 101 selected entries in this annotated bibliography of Egyptian materials on education published in 1975. Materials include journal articles, books, and government documents. The bibliography covers the following topics: academic certificates and dissertations, art education, audiovisual aids, camps, civics curricula, conferences and…

Selected Bibliography of Egyptian Educational Materials, Vol. 1, No. 2, 1975.

Science.gov (United States)

Al-Ahram Center for Scientific Translations, Cairo (Egypt).

There are 108 selected entries in this annotated bibliography of Egyptian materials on education published in 1975. Materials include journal articles, books, and government documents. The bibliography covers the following topics: adolescence, art education, child upbringing, comprehensive schools, curricula, educational change, educational aids,…

Assessment of the methane oxidation capacity of compacted soils intended for use as landfill cover materials

International Nuclear Information System (INIS)

Rachor, Ingke; Gebert, Julia; Groengroeft, Alexander; Pfeiffer, Eva-Maria

2011-01-01

The microbial oxidation of methane in engineered cover soils is considered a potent option for the mitigation of emissions from old landfills or sites containing wastes of low methane generation rates. A laboratory column study was conducted in order to derive design criteria that enable construction of an effective methane oxidising cover from the range of soils that are available to the landfill operator. Therefore, the methane oxidation capacity of different soils was assessed under simulated landfill conditions. Five sandy potential landfill top cover materials with varying contents of silt and clay were investigated with respect to methane oxidation and corresponding soil gas composition over a period of four months. The soils were compacted to 95% of their specific proctor density, resulting in bulk densities of 1.4-1.7 g cm -3 , reflecting considerably unfavourable conditions for methane oxidation due to reduced air-filled porosity. The soil water content was adjusted to field capacity, resulting in water contents ranging from 16.2 to 48.5 vol.%. The investigated inlet fluxes ranged from 25 to about 100 g CH 4 m -2 d -1 , covering the methane load proposed to allow for complete oxidation in landfill covers under Western European climate conditions and hence being suggested as a criterion for release from aftercare. The vertical distribution of gas concentrations, methane flux balances as well as stable carbon isotope studies allowed for clear process identifications. Higher inlet fluxes led to a reduction of the aerated zone, an increase in the absolute methane oxidation rate and a decline of the relative proportion of oxidized methane. For each material, a specific maximum oxidation rate was determined, which varied between 20 and 95 g CH 4 m -2 d -1 and which was positively correlated to the air-filled porosity of the soil. Methane oxidation efficiencies and gas profile data imply a strong link between oxidation capacity and diffusive ingress of

Inhibition of Corneal Neovascularization by Topical and Subconjunctival Tigecycline

Directory of Open Access Journals (Sweden)

Sertan Goktas

2014-01-01

Full Text Available Objective. To investigate the effects of topical and subconjunctival tigecycline on the prevention of corneal neovascularization. Materials and Methods. Following chemical burn, thirty-two rats were treated daily with topical instillation of 1 mg/mL tigecycline (group 1 or subconjunctival instillation of 1 mg/mL tigecycline (group 3 for 7 days. Control rats received topical (group 2 or subconjunctival (group 4 0.9% saline. Digital photographs of the cornea were taken on the eighth day after treatment and analyzed to determine the percentage area of the cornea covered by neovascularization. Corneal sections were analyzed histopathologically. Results. The median percentages of corneal neovascularization in groups 1 and 3 were 48% (95% confidence interval (CI, 44.2–55.8% and 33.5% (95% CI, 26.6–39.2%, respectively. The median percentages of corneal neovascularization of groups 1 and 3 were significantly lower than that of the control group (P=0.03 and P<0.001, resp.. Histologic examination of samples from groups 1 and 3 showed lower vascularity than that of control groups. Conclusion. Topical and subconjunctival administration of tigecycline seems to be showing promising therapeutic effects on the prevention of corneal neovascularization. Furthermore, subconjunctival administration of tigecycline is more potent than topical administration in the inhibition of corneal neovascularization.

2011 annual meeting on nuclear technology. Pt. 4. Topical sessions

International Nuclear Information System (INIS)

Schoenfelder, Christian; Dams, Wolfgang

2011-01-01

Summary report on the Topical Session of the Annual Conference on Nuclear Technology held in Berlin, 17 to 19 May 2011: - Nuclear Competence in Germany and Europe. The Topical Session: - Sodium Cooled Fast Reactors -- will be covered in a report in a further issue of atw. The reports on the Topical Sessions: - CFD-Simulations for Safety Relevant Tasks; and - Final Disposal: From Scientific Basis to Application; - Characteristics of a High Reliability Organization (HRO) Considering Experience Gained from Events at Nuclear Power Stations -- have been covered in atw 7, 8/9, and 10 (2011). (orig.)

International topical meeting on nuclear research applications and utilization of accelerators. Book of abstracts

International Nuclear Information System (INIS)

2009-01-01

Applications of particle accelerators cover a number of areas, from strategic and applied research, safety and security, environmental applications, materials research and analytical sciences, to radioisotope production and radiation processing. Accelerator based techniques and pulsed neutron sources are expected to lead to new initiatives in materials research of relevance for both the nuclear and non-nuclear fields. Material science studies with the use of accelerators, neutron beams and other nuclear analytical methods are relevant to the development of advanced reactors, nuclear fuel cycle needs and fusion research. In this regard, a better understanding of the irradiation effects in materials for energy and non-energy applications is needed, and is reflected in accelerator techniques for modification and analysis of materials for nuclear technologies. Accelerator applications for innovative nuclear systems aiming at rad-waste transmutation (e.g., accelerator driven systems) are being pursued in many countries. Research and development using accelerators involves a broad spectrum of skills to build a cadre of trained experts in nuclear techniques in IAEA Member States, and to generate knowledge for innovative methodologies and tools. The present conference is also being held in cooperation with the American Nuclear Society (ANS), which successfully organized the series of accelerator applications conferences known as AccApp. The ANS series of topical meetings has provided a forum for the global exchange of scientific and technical knowledge on a wide variety of related topics since the first AccApp took place in 1997 in Albuquerque, USA. The last conference which was held in 2007 in Pocatello, USA, was jointly organized by the ANS and the IAEA. The main objectives of the conference are to promote exchange of information among IAEA Member States representatives/delegates and to discuss new trends in accelerator applications including nuclear materials research

Key Topics in Sports Medicine

OpenAIRE

2006-01-01

Key Topics in Sports Medicine is a single quick reference source for sports and exercise medicine. It presents the essential information from across relevant topic areas, and includes both the core and emerging issues in this rapidly developing field. It covers: 1) Sports injuries, rehabilitation and injury prevention, 2) Exercise physiology, fitness testing and training, 3) Drugs in sport, 4) Exercise and health promotion, 5) Sport and exercise for special and clinical populations, 6) The ps...

Advanced research workshop: nuclear materials safety

International Nuclear Information System (INIS)

Jardine, L J; Moshkov, M M.

1999-01-01

The Advanced Research Workshop (ARW) on Nuclear Materials Safety held June 8-10, 1998, in St. Petersburg, Russia, was attended by 27 Russian experts from 14 different Russian organizations, seven European experts from six different organizations, and 14 U.S. experts from seven different organizations. The ARW was conducted at the State Education Center (SEC), a former Minatom nuclear training center in St. Petersburg. Thirty-three technical presentations were made using simultaneous translations. These presentations are reprinted in this volume as a formal ARW Proceedings in the NATO Science Series. The representative technical papers contained here cover nuclear material safety topics on the storage and disposition of excess plutonium and high enriched uranium (HEU) fissile materials, including vitrification, mixed oxide (MOX) fuel fabrication, plutonium ceramics, reprocessing, geologic disposal, transportation, and Russian regulatory processes. This ARW completed discussions by experts of the nuclear materials safety topics that were not covered in the previous, companion ARW on Nuclear Materials Safety held in Amarillo, Texas, in March 1997. These two workshops, when viewed together as a set, have addressed most nuclear material aspects of the storage and disposition operations required for excess HEU and plutonium. As a result, specific experts in nuclear materials safety have been identified, know each other from their participation in t he two ARW interactions, and have developed a partial consensus and dialogue on the most urgent nuclear materials safety topics to be addressed in a formal bilateral program on t he subject. A strong basis now exists for maintaining and developing a continuing dialogue between Russian, European, and U.S. experts in nuclear materials safety that will improve the safety of future nuclear materials operations in all the countries involved because of t he positive synergistic effects of focusing these diverse backgrounds of

Models, Databases, and Simulation Tools Needed for the Realization of Integrated Computational Materials Engineering. Proceedings of the Symposium Held at Materials Science and Technology 2010

Science.gov (United States)

Arnold, Steven M. (Editor); Wong, Terry T. (Editor)

2011-01-01

Topics covered include: An Annotative Review of Multiscale Modeling and its Application to Scales Inherent in the Field of ICME; and A Multiscale, Nonlinear, Modeling Framework Enabling the Design and Analysis of Composite Materials and Structures.

Proceedings of the international conference on advances in metallic materials and manufacturing processes for strategic sectors: souvenir and book of abstracts

International Nuclear Information System (INIS)

2012-01-01

Topics like materials processing, ultrafine grained materials, powder metallurgical processing, composite materials,, mechanical processing, materials characterisation, materials joining, failure analysis and corrosion and functional and nano materials are covered in this symposium. Papers relevant to INIS are indexed separately

Laser-beam interactions with materials

International Nuclear Information System (INIS)

Allmen, M.V.

1987-01-01

Lasers are becoming popular tools and research instruments in materials research, metallurgy, semiconductor technology and engineering. This text treats, from a physicist's point of view, the processes that lasers can induce in materials. A broad view of the field and its perspectives is given: physical topics covered range from optics to shock waves, and applications range from semiconductor annealing to fusion-plasma production. Intuitive analytical models are used whenever possible, in order to foster creative thinking and facilitate access to newcomers and nonspecialists

Hiroshima. History and topicality of the atomic threat. Baseline material and information for education

International Nuclear Information System (INIS)

Verfuss, K.; Wunderer, H.

1995-01-01

Hiroshima is an important topic for education, not only in history and social sciences classes, but just as well for courses in German, ethics, religion, and in the natural sciences. The material has been compiled to serve as an information source both for specific subjects and for interdisciplinary approaches, and has been arranged in compliance with the didactic principles of multiperspective approach and controversial aspects. (orig.) [de

Section 608 Technician Certification Test Topics

Science.gov (United States)

Identifies some of the topics covered on Section 608 Technician Certification tests such as ozone depletion, the Clean Air Act and Montreal Protocol, Substitute Refrigerants and oils, Refrigeration and Recovery Techniques.

The effects of covering materials on indoor Rn concentrations in offices in Hong Kong

International Nuclear Information System (INIS)

Yu, K.N.; Cheung, T.; Young, E.C.M.; Mui, W.N.; Tang, K.K.

2000-01-01

The variation of Rn concentrations in 134 offices with different covering materials cladded on internal building surfaces, including walls, ceilings and floors, were measured. The three commonest combinations (87 sites) of covering materials for the walls, ceilings and floors in Hong Kong are (A): wall paper, fibre board, carpet; (B): paint, paint and plastic tile and (C): paint, fibre board, plastic tile. The average Rn concentrations for combinations (A) and (B) were about the same, while that for combination (C) was significantly lower than those for (A) and (B). A person working in an office with combination (C) can receive an average annual tracheobronchial equivalent dose smaller than one working in an office with combinations (A) and (B) by an amount as large as 0.8 mSv

Investigation of Lipid Oxidation in the Raw Materials of a Topical Skin Formulation: A Topical Skin Formulation Containing a High Lipid Content

DEFF Research Database (Denmark)

Thomsen, Birgitte Raagaard; Taylor, Richard; Madsen, Robert

2018-01-01

Several studies have demonstrated that lipid oxidation often occurs in topical skin formulations which can affect product odor (both positively and negatively). Furthermore, odor detection threshold values and odor descriptors of identified volatile oxidation products in cleansing and skin cream...... formulation prototypes were recently determined by a trained sensory panel at the Technical University of Denmark in the Division of Food Technology. In this study, we investigated lipid oxidation in a prototype skin cream formulation as well as in selected cosmetic skin care raw materials. Lipid oxidation...... was also identified. In addition, the concentrations of several well-known lipid oxidation products increased during storage and were suggested to originate primarily from rice bran wax, which oxidized more readily than other raw materials due to its unsaturated nature....

Proceedings of the international symposium for research scholars on metallurgy, materials science and engineering

International Nuclear Information System (INIS)

2010-01-01

Topics covered in this symposium are: steels, functional materials posters, computational materials science, casting and solidification, polymer matrix composites, posters electronic materials, environmental degradation processing of non-metallic materials posters, energy materials, materials forming technology, biomaterials, magnetic materials, mechanical behaviour of materials posters, phase transformations and physical metallurgy, surface engineering, nanostructured materials, ceramics, processing of metals, materials joining technology and optical materials. Papers relevant to INIS are indexed separately

Treatment Duration of Topics in Senior Secondary School Core ...

African Journals Online (AJOL)

kofimereku

years to better equip the students for university education (Daily Graphic of. September 15th 1998). .... five items similar to those in the SS Mathematics Book 3, and covered all the sub-topics of the topic ..... Soviet Union. United States. 181. 188.

Evaluation of geologic materials to limit biological intrusion of low-level waste site covers

International Nuclear Information System (INIS)

Hakonson, T.E.; White, G.C.; Karlen, E.M.

1982-01-01

The long-term integrity of low-level waste shallow land burial sites is dependent on the interaction of physical, chemical, and biological factors that modify the waste containment system. This paper reports the preliminary results of a screening study to-determine the effectiveness of four biobarrier materials to stop plant root and animal penetration into simulated low-level wastes. Experiments employed 288 lysimeters consisting of 25-cm-diam PVC pipe, with four factors tested: plant species (alfalfa, barley, and sweet clover); top soil thickness (30 and 60 cm); biobarrier material (crushed tuff, bentonite clay, cobble, and cobble-gravel); and biobarrier thickness (clay-15, 30, and 45 cm, others 30, 60, and 90 cm). The crushed tuff, a sandy backfill material, offers little resistance to root and animal intrusion through the cover profile, while bentonite clay, cobble, and cobble-gravel combinations do reduce plant root and animal intrusion thorugh cover profiles. However, dessication of the clay barrier by invading plant roots may limit the usefulness of this material as a moisture and/or biological barrier. The cobble-gravel combination appears to be the best candidate for further testing on a larger scale because the gravel helps impede the imgration of soil into the cobble layer - the probable cause of failure of cobble-only biobarriers

Guidance for disposal of uranium-mill tailings: long-term stabilization of earthen cover materials

International Nuclear Information System (INIS)

Voorhees, L.D.; Sale, M.J.; Webb, J.W.; Mulholland, P.J.

1983-06-01

The primary hazard associated with uranium-mill tailings is exposure to a radioactive gas, 222 Rn, the concentration of which has been correlated with the occurrence of lung cancer. Previous studies on radon attenuation conclude that the placement of earthen cover materials over the tailings is the most effective technique for reducing radioactive emissions and dispersal of tailings. The success of such a plan, however, depends on long-term protection of these cover materials. 230 Th, which decays to 222 Rn, has a half-life of about 80,000 years. The three major options available for stabilization of uranium-mill tailings are (1) rock cover, (2) soil and revegetation, or (3) a combination of both on different portions of the tailings cover. The optimal choice among these alternatives depends on site-specific characteristics such as climate and local geomorphology and soils, and on design variables such as embankment heights and slopes, modification of upstream drainage, and revegetation practices. Generally, geomorphic evidence suggests that use of soil and vegetation alone will not be adequate to reduce erosion on slopes greater than about 5 0 . For these steeper slopes, riprap will be necessary to maximize the probability of long-term stability. The use of vegetation to control erosion on the flatter portions of the site may be practicable in regions with sufficient rainfall and suitable soil types, but revegetation practices must be carefully evaluated

Topics in current aerosol research

CERN Document Server

Hidy, G M

1971-01-01

Topics in Current Aerosol Research deals with the fundamental aspects of aerosol science, with emphasis on experiment and theory describing highly dispersed aerosols (HDAs) as well as the dynamics of charged suspensions. Topics covered range from the basic properties of HDAs to their formation and methods of generation; sources of electric charges; interactions between fluid and aerosol particles; and one-dimensional motion of charged cloud of particles. This volume is comprised of 13 chapters and begins with an introduction to the basic properties of HDAs, followed by a discussion on the form

Structural analysis of hatch cover plates on Fuels and Materials Examination Facility high bay mezzanine

International Nuclear Information System (INIS)

Dixson, G.E.

1997-01-01

In order to move the Idaho National Engineering Laboratory (INEL) Light Duty Utility Arm (LDUA) trailer into position for testing on the Fuels and Materials Examination Facility (FMEF) 42 ft level mezzanine one of the trailer's wheels will have to sit on a circular hatch cover fabricated from one-inch thick steel plate. The attached calculations verify that the hatch cover plate is strong enough to support the weight of the INEL LDUA trailer's wheel

Let's start learning radiation. Supplementary material on radiation for secondary school students

International Nuclear Information System (INIS)

Watanabe, Yoko; Yamashita, Kiyonobu; Shimada, Mayuka

2015-01-01

The Japan Atomic Energy Agency has been organizing training programs for engineers in Asian countries introducing nuclear technology. In 2012, we launched a course ‘Basic Radiation Knowledge for School Education’ as we thought disseminating accurate knowledge on radiation to school students and public would also be important in those countries after Fukushima-Daiichi nuclear power station accident. Ministry of Education, Culture, Sports, Science and Technology - Japan published supplemental learning material on radiation for secondary school students and teachers in Japanese in October 2011. Since the learning material is designed to give a clear explanation of radiation and covers various topics, we thought it would also be beneficial for young students in the world if a learning material in English was available. Therefore, we made a new learning material in English using the topics covered in supplemental learning material on radiation in Japanese as a reference. This learning material has been favourably evaluated by the International Atomic Energy Agency (IAEA) and will be widely used as a practical educational tool in many countries around the world through the IAEA. (author)

Topics in supergravity and string theory

International Nuclear Information System (INIS)

Eastaugh, A.G.

1987-01-01

The first topic covered in this dissertation concerns the harmonic expansion technique and its application to the dimensional compactification of higher dimensional supergravity. A simple example is given to explain the method and then the method is applied to the problem of obtaining the mass spectrum of the squashed seven-sphere compactification of eleven dimensional supergravity. The second topic concerns the application of Fujikawa's method of anomaly calculation to the calculation of the critical dimension of various string models. The third topic is a study and explicit calculation of the Fock space representation of the vertex in Witten's formulation of the interacting open bosonic string field theory

Interaction of Electromagnetic Waves with Two-Dimensional Metal Covered with Radar Absorbing Material and Plasma

International Nuclear Information System (INIS)

Lan Chaohui; Hu Xiwei; Jiang Zhonghe

2008-01-01

A two-dimensional metal model is established to investigate the stealth mechanisms of radar absorbing material (RAM) and plasma when they cover the model together. Using the finite-difference time-domain (FDTD) method, the interaction of electromagnetic (EM) waves with the model can be studied. In this paper, three covering cases are considered: a. RAM or plasma covering the metal solely; b. RAM and plasma covering the metal, while plasma is placed outside; c. RAM and plasma covering the metal, while RAM is placed outside. The calculated results show that the covering order has a great influence on the absorption of EM waves. Compared to case a, case b has an advantage in the absorption of relatively high-frequency EM waves (HFWs), whereas case c has an advantage in the absorption of relatively low-frequency EM waves (LFWs). Through the optimization of the parameters of both plasma and RAM, it is hopeful to obtain a broad absorption band by RAM and plasma covering. Near-field attenuation rate and far-field radar cross section (RCS) are employed to compare the different cases. (low temperature plasma)

Annual review of materials science. Volume 7

International Nuclear Information System (INIS)

Huggins, R.A.; Bube, R.H.; Roberts, R.W.

1977-01-01

A review is presented of recent materials science research. Topics covered include: point defects and their interaction; defect chemistry in crystalline solids; deep level impurities in semiconductors; structural aspects of one-dimensional conductors; structural transformations during aging of metal alloys; high rate thick film growth; metal forming, the application of limit analysis; kinetics and mechanisms of gas-metal interactions; erosion; reversible temper embrittlement; acoustic emission in brittle materials; capacitance transient spectroscopy; hot corrosion of high-temperature alloys; fundamental optical phenomena in infrared window materials; dental amalgam; and transparent conducting coatings

Using NASA Space Imaging Technology to Teach Earth and Sun Topics

Science.gov (United States)

Verner, E.; Bruhweiler, F. C.; Long, T.

2011-12-01

We teach an experimental college-level course, directed toward elementary education majors, emphasizing "hands-on" activities that can be easily applied to the elementary classroom. This course, Physics 240: "The Sun-Earth Connection" includes various ways to study selected topics in physics, earth science, and basic astronomy. Our lesson plans and EPO materials make extensive use of NASA imagery and cover topics about magnetism, the solar photospheric, chromospheric, coronal spectra, as well as earth science and climate. In addition we are developing and will cover topics on ecosystem structure, biomass and water on Earth. We strive to free the non-science undergraduate from the "fear of science" and replace it with the excitement of science such that these future teachers will carry this excitement to their future students. Hands-on experiments, computer simulations, analysis of real NASA data, and vigorous seminar discussions are blended in an inquiry-driven curriculum to instill confident understanding of basic physical science and modern, effective methods for teaching it. The course also demonstrates ways how scientific thinking and hands-on activities could be implemented in the classroom. We have designed this course to provide the non-science student a confident basic understanding of physical science and modern, effective methods for teaching it. Most of topics were selected using National Science Standards and National Mathematics Standards that are addressed in grades K-8. The course focuses on helping education majors: 1) Build knowledge of scientific concepts and processes; 2) Understand the measurable attributes of objects and the units and methods of measurements; 3) Conduct data analysis (collecting, organizing, presenting scientific data, and to predict the result); 4) Use hands-on approaches to teach science; 5) Be familiar with Internet science teaching resources. Here we share our experiences and challenges we face while teaching this course.

NASA Materials Research for Extreme Conditions

Science.gov (United States)

Sharpe, R. J.; Wright, M. D.

2009-01-01

This Technical Memorandum briefly covers various innovations in materials science and development throughout the course of the American Space program. It details each innovation s discovery and development, explains its significance, and describes the applications of this material either in the time period discovered or today. Topics of research include silazane polymers, solvent-resistant elastomeric polymers (polyurethanes and polyisocyanurates), siloxanes, the Space Shuttle thermal protection system, phenolic-impregnated carbon ablator, and carbon nanotubes. Significance of these developments includes the Space Shuttle, Apollo programs, and the Constellation program.

Covering of the electric power service

International Nuclear Information System (INIS)

Unidad de Planeacion Minero Energetica, UPME

2000-01-01

In this article it is sought to deepen more in the topic of the covering of the electric power service, especially in the related with the mechanisms that could facilitate their amplification. In the new market outline, in the one that the participation of the agents is encouraged in all the activities of the chain of services in which the state is not direct lender of the same one, it is confused the form like a covering will be achieved that is of agreement with the goals that intend in the national plan of development and in the sub sectorial plans. Although the rules of the market one comes consolidating, the process of linking of the private capital, especially in the distribution activity, it evidences the importance of to settle down and to define responsibilities and explicit mechanisms in the topic of expansion of the covering. A first interpretation of the ruled indicates the obligation of the state of extending the covering to 100% and of assuming the projects that don't undertake the matters. This would be the reading from the traditional mentality. However, the regulation of you public services of electricity don't demand a total covering, but rather it covers to the users that have the capacity to assume, with their own resources, the efficient costs of benefit. The service will also be lent to residential users that don't have payment capacity, when there are contribution resources or fiscal resources for subsidiary

Proceedings of the DAE-BRNS fourth interdisciplinary symposium on materials chemistry

International Nuclear Information System (INIS)

Tyagi, D.; Banerjee, A.M.; Bhattacharyya, K.; Nigam, S.; Varma, S.; Tripathi, A.K.; Das, D.

2012-12-01

This symposium covers almost all the contemporary research areas of materials chemistry like materials for energy conversion, biomaterials, carbon based materials, chemical sensors, fuel cell materials and other electro-ceramics, polymers and soft condensed matters, thin films and surface chemistry, organic and organometallics, high purity materials, nanomaterials and clusters to acquaint ourselves with the advancement made in these emerging areas. Topics like nuclear materials, magnetic materials, catalysis and computational materials chemistry continue to be important facet of ISMC series of symposia. Papers relevant to INIS are indexed separately

Joint EC-IAEA topical meeting on development of new structural materials for advanced fission and fusion reactor systems. PowerPoint presentations

International Nuclear Information System (INIS)

2009-01-01

The key topics of the meeting are the following: Radiation damage phenomena and modelling of material properties under irradiation; On-going challenges in radiation materials science; Key material parameters and operational conditions of selected reactor designs; Microstructures and mechanical properties of nuclear structural materials; Pathways to development of new structural materials; Qualification of new structural materials; Advanced microstructure probing methods; Special emphasis is given to the application of nuclear techniques in the development and qualification of new structural materials.

High temperature materials and mechanisms

CERN Document Server

2014-01-01

The use of high-temperature materials in current and future applications, including silicone materials for handling hot foods and metal alloys for developing high-speed aircraft and spacecraft systems, has generated a growing interest in high-temperature technologies. High Temperature Materials and Mechanisms explores a broad range of issues related to high-temperature materials and mechanisms that operate in harsh conditions. While some applications involve the use of materials at high temperatures, others require materials processed at high temperatures for use at room temperature. High-temperature materials must also be resistant to related causes of damage, such as oxidation and corrosion, which are accelerated with increased temperatures. This book examines high-temperature materials and mechanisms from many angles. It covers the topics of processes, materials characterization methods, and the nondestructive evaluation and health monitoring of high-temperature materials and structures. It describes the ...

Detection of smuggling of nuclear material covered by a legal transport of radioactive material

International Nuclear Information System (INIS)

Safar, J.; Zsigrai, J.; Tam, N.C.; Lakosi, L.

2001-01-01

Full text: One of the worst scenarios for detection of illicit trafficking of nuclear material is when a legal transport of radioactive material is used to cover the radiation of the smuggled uranium. Feasibility study was performed in the Institute of Isotopes and Surface Chemistry of the Chemical Research Centre of the Hungarian Academy of Sciences (hereinafter: Institute) in order to study the possible on site measurement techniques and approaches applicable in such cases. As the type A and type B packages always incorporate a feature such as a seal, in a realistic scenario the confiscated nuclear material is expected to be placed outside the package. The passive neutron emission of the uranium is negligible for a reasonable isotopic abundance therefore the feasibility study was concentrating on non-destructive, passive gamma- spectrometric methods. Possible application of Nal (diameter 40x40 mm 3 , large planar (15x15x3 mm 3 ) and a hemispheric CdZnTe (500 mm 3 , and high purity Germanium detectors was investigated. During the on site measurements portable electronics, mini multichannel analyzer, palmtop and/or notebook computer were used. The shielding material of the packages was lead or depleted uranium. The smuggled material was simulated by a package of reactor fuel pellets containing low enriched or natural uranium (materials confiscated in earlier cases) and standards containing low enriched uranium. During the supposed scenario the portal monitor provides an indication of an elevated level of the environmental radioactivity. Then the responsible (e.g. customs) officer investigate the vehicle by a hand-held survey meter in order to search for peaks in dose rates. If a peak was localized, which is different from the position of the legally transported package(s) the officer requests for the expertise of the designated institutes. The following model cases provided the basic conclusion: 1. The legal transport of the radioactive material was simulated by a

Design of Molecular Materials: Supramolecular Engineering

Science.gov (United States)

Simon, Jacques; Bassoul, Pierre

2001-02-01

This timely and fascinating book is destined to be recognised as THE book on supramolecular engineering protocols. It covers this sometimes difficult subject in an approachable form, gathering together information from many sources. Supramolecular chemistry, which links organic chemistry to materials science, is one of the fastest growth areas of chemistry research. This book creates a correlation between the structure of single molecules and the physical and chemical properties of the resulting materials. By making systematic changes to the component molecules, the resulting solid can be engineered for optimum performance. There is a clearly written development from synthesis of designer molecules to properties of solids and further on to devices and complex materials systems, providing guidelines for mastering the organisation of these systems. Topics covered include: Systemic chemistry Molecular assemblies Notions of symmetry Supramolecular engineering Principe de Curie Organisation in molecular media Molecular semiconductors Industrial applications of molecular materials This superb book will be invaluable to researchers in the field of supramolecular materials and also to students and teachers of the subject.

Veterinary Specialist, 1-2. Military Curriculum Materials for Vocational and Technical Education.

Science.gov (United States)

Ohio State Univ., Columbus. National Center for Research in Vocational Education.

These military-developed curriculum materials consist of five volumes of text information, student workbooks, and supplements for use in training veterinary specialists. Covered in the individual volumes are the following topics: the veterinary airman, administration, and statistical procedures; veterinary microbiology, consumer-level quality…

Proceedings of the third Asian symposium on materials and processing: souvenir

International Nuclear Information System (INIS)

2012-01-01

Materials characterization and measurement techniques, materials processing, forming, casting and machining, mechanical properties, fracture and reliability, metals, ceramics, polymers and composites, modeling, analysis and simulation in materials and processing, nano fabrication and nano/micro/meso manufacturing processes and advanced manufacturing, non-destructive testing and evaluations, monitoring and sensing technology, powder metallurgy, adhesion and interface, welding and bonding, smart materials and structures, functional materials, surface engineering and thin films and coatings are the topics covered in this symposium. Papers relevant to INIS are indexed separately

Diffuse scattering and the fundamental properties of materials

CERN Document Server

EIce, Gene; Barabash, Rozaliya

2009-01-01

Diffuse Scattering-the use of off-specular X-Rays and neutrons from surfaces and interfaces-has grown rapidly as a tool for characterizing the surface properties of materials and related fundamental structural properties. It has proven to be especially useful in the understanding of local properties within materials. This book reflects the efforts of physicists and materials scientists around the world who have helped to refine the techniques and applications of diffuse scattering. Major topics specifically covered include: -- Scattering in Low Dimensions -- Elastic and Thermal Diffuse Scattering from Alloys -- Scattering from Complex and Disordered Materials -- Scattering from Distorted Crystals.

Selected Bibliography of Egyptian Educational Materials. Vol. 3, No. 4, 1977.

Science.gov (United States)

Al-Ahram Center for Scientific Translations, Cairo (Egypt).

Over 130 citations of books, journals, government publications, and newspapers dealing with education in Egypt are included in this annotated bibliography. Materials cited were published in 1977. Sixty-two alphabetically arranged categories cover such topics as agricultural schools, Arabic language, basic education, child care, curricula,…

SETI: A good introductory physics topic

Science.gov (United States)

Hobson, Art

1997-04-01

If America is to achieve the science literacy that is essential to industrialized democracy, all students must study such topics as scientific methodology, pseudoscience, ozone depletion, and global warming. My large-enrollment liberal-arts physics course covers the great principles of physics along with several such philosophical and societal topics. It is easy to include the interdisciplinary context of physics in courses for non-scientists, because these courses are flexible, conceptual, and taught to students whose interests span a broad range. Students find these topics relevant and fascinating, leading to large enrollments by non-scientists even in courses labeled ''physics.'' I will discuss my approach to teaching the search for extra-terrestrial intelligence (SETI), a topic with lots of good physics and with connections to scientific methodology and pseudoscience. A textbook for this kind of course has been published, Physics: Concepts and Connections (Prentice-Hall, 1995).

Dressings and topical agents for surgical wounds healing by secondary intention

NARCIS (Netherlands)

Vermeulen, H.; Ubbink, D.; Goossens, A.; de Vos, R.; Legemate, D.

2004-01-01

BACKGROUND: Many different wound dressings and topical applications are used to cover surgical wounds healing by secondary intention. It is not known whether these dressings heal wounds at different rates. OBJECTIVES: To assess the effectiveness of dressings and topical agents on surgical wounds

Conference on Stochastic Analysis and Related Topics

CERN Document Server

Peterson, Jonathon

2017-01-01

The articles in this collection are a sampling of some of the research presented during the conference “Stochastic Analysis and Related Topics”, held in May of 2015 at Purdue University in honor of the 60th birthday of Rodrigo Bañuelos. A wide variety of topics in probability theory is covered in these proceedings, including heat kernel estimates, Malliavin calculus, rough paths differential equations, Lévy processes, Brownian motion on manifolds, and spin glasses, among other topics.

Selected topics from classical bacterial genetics.

Science.gov (United States)

Raleigh, Elisabeth A; Elbing, Karen; Brent, Roger

2002-08-01

Current cloning technology exploits many facts learned from classical bacterial genetics. This unit covers those that are critical to understanding the techniques described in this book. Topics include antibiotics, the LAC operon, the F factor, nonsense suppressors, genetic markers, genotype and phenotype, DNA restriction, modification and methylation and recombination.

Laser additive manufacturing of high-performance materials

CERN Document Server

Gu, Dongdong

2015-01-01

This book entitled “Laser Additive Manufacturing of High-Performance Materials” covers the specific aspects of laser additive manufacturing of high-performance new materials components based on an unconventional materials incremental manufacturing philosophy, in terms of materials design and preparation, process control and optimization, and theories of physical and chemical metallurgy. This book describes the capabilities and characteristics of the development of new metallic materials components by laser additive manufacturing process, including nanostructured materials, in situ composite materials, particle reinforced metal matrix composites, etc. The topics presented in this book, similar as laser additive manufacturing technology itself, show a significant interdisciplinary feature, integrating laser technology, materials science, metallurgical engineering, and mechanical engineering. This is a book for researchers, students, practicing engineers, and manufacturing industry professionals interested i...

Hot Topics/New Initiatives | Drinking Water in New England ...

Science.gov (United States)

2017-07-06

Information on Drinking Water in New England. Major Topics covered include: Conservation, Private Wells, Preventing Contamination, Drinking Water Sources, Consumer Confidence Reports, and Drinking Water Awards.

Specialists meeting on properties of primary circuit structural materials including environmental effects

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-07-01

The Specialists Meeting on Properties of Primary Circuit Structural Materials of LMFBRs covered the following topics: overview of materials program in different countries; mechanical properties of materials in air; fracture mechanics studies - component related activities; impact of environmental influences on mechanical properties; relationship of material properties and design methods. The purpose of the meeting was to provide a forum for exchange of information on structural materials behaviour in primary circuit of fast breeder reactors. Special emphasis was placed on environmental effects such as influence of sodium and irradiation on mechanical properties of reactor materials.

Specialists meeting on properties of primary circuit structural materials including environmental effects

International Nuclear Information System (INIS)

1977-01-01

The Specialists Meeting on Properties of Primary Circuit Structural Materials of LMFBRs covered the following topics: overview of materials program in different countries; mechanical properties of materials in air; fracture mechanics studies - component related activities; impact of environmental influences on mechanical properties; relationship of material properties and design methods. The purpose of the meeting was to provide a forum for exchange of information on structural materials behaviour in primary circuit of fast breeder reactors. Special emphasis was placed on environmental effects such as influence of sodium and irradiation on mechanical properties of reactor materials

Hotel and Restaurant Management; A Bibliography of Books and Audio-Visual Materials.

Science.gov (United States)

Malkames, James P.; And Others

This bibliography represents a collection of 1,300 book volumes and audiovisual materials collected by the Luzerne County Community College Library in support of the college's Hotel and Restaurant Management curriculum. It covers such diverse topics as advertising, business practices, decoration, nutrition, hotel law, insurance landscaping, health…

Metals and Ceramics Division materials science annual progress report for period ending June 30, 1978

International Nuclear Information System (INIS)

McHargue, C.J.; Peterson, S.

1978-09-01

Topics covered include: structure of materials, theoretical research; x-ray diffraction research; fundamental ceramics studies; preparation and synthesis of high-temperature and special service materials; physical metallurgy; grain boundary segregation and fracture; mechanisms of surface and solid-state reactions; physical properties research; superconducting materials; radiation effects; facility and technique development; nuclear microanalysis; cooperative studies with universities and other research organizations; and fundamentals of welding and joining

Applied atomic and collision physics special topics

CERN Document Server

Massey, H S W; Bederson, Benjamin

1982-01-01

Applied Atomic Collision Physics, Volume 5: Special Topics deals with topics on applications of atomic collisions that were not covered in the first four volumes of the treatise. The book opens with a chapter on ultrasensitive chemical detectors. This is followed by separate chapters on lighting, magnetohydrodynamic electrical power generation, gas breakdown and high voltage insulating gases, thermionic energy converters, and charged particle detectors. Subsequent chapters deal with the operation of multiwire drift and proportional chambers and streamer chambers and their use in high energy p

EMaCC: FY-1978 topical area report

International Nuclear Information System (INIS)

1979-04-01

Materials research and development in the energy program are briefly described. Topics reviewed include joining of materials, elastomers, catalysts and catalytic effect, radiation effects, superconductivity, cement, concrete, and alternate materials

Study of hydrological and geochemical data on materials for the final cover of subsurface storage sites

International Nuclear Information System (INIS)

Sauter, M.M.; Barres, M.; Faby, J.

1987-01-01

The European Research program includes studies on highly watertight materials likely to sait the final cover of low-level and intermediate-level waste disposal. The experimental equipment is composed of a 26 sq. m collector placed on an inclined plane, just below the material to be tested and connected by means of a gutter with a measuring room where the infiltration waters flow rate is steadily measured. On the surface of the tumulus, a 300 sq.m inclined plane permits the measure of the running off water. The recording raingauge completes the device. Water vapour pressures are measured at different depths within the material. Total watercontents are registered along vertical profils using a special neutron logging tool. Numerous physico-chemical measures are carried out on the infiltration and running off waters: pH, Eh, temperature, dissolved oxygen, conductivity, turbidity and major anions and cations. Two materials have been tested with this device: - weathered schists; Compacted clay. The first material showed that, on average over the six months period of measurements, the overall rainfall brokedown into 11% running waters, 13% infiltration and 76% evaporation because infiltration accounts for a large part of rainfall. It resulted in a complete saturation of the material during certain periods of the year. Humidity measurements performed at different places pointed out large heterogeneities inside the material. It is worth noting that, despite some problems due to calibration, the whole instrumentation located in the measuring room worked rather well and permitted to demonstate the bad qualities of the material. The second material was subsequently covered by a 20 cm thick layer made of a mixture of sand in order to regularize water infiltration under the soil vegetation constituted by a special grass growing

Topics in current aerosol research (part2)

CERN Document Server

Hidy, G M

1972-01-01

Topics in Current Aerosol Research, Part 2 contains some selected articles in the field of aerosol study. The chosen topics deal extensively with the theory of diffusiophoresis and thermophoresis. Also covered in the book is the mathematical treatment of integrodifferential equations originating from the theory of aerosol coagulation. The book is the third volume of the series entitled International Reviews in Aerosol Physics and Chemistry. The text offers significant understanding of the methods employed to develop a theory for thermophoretic and diffusiophoretic forces acting on spheres in t

Novel functional magnetic materials fundamentals and applications

CERN Document Server

2016-01-01

This book presents current research on advanced magnetic materials and multifunctional composites. Recent advances in technology and engineering have resulted from the development of advanced magnetic materials with improved functional magnetic and magneto-transport properties. Certain industrial sectors, such as magnetic sensors, microelectronics, and security, demand cost-effective materials with reduced dimensionality and desirable magnetic properties such as enhanced magnetic softness, giant magnetic field sensitivity, and large magnetocaloric effect.  Expert chapters present the most up-to-date information on the fabrication process, processing, tailoring of properties, and applications of different families of modern functional materials for advanced smart applications. Topics covered include novel magnetic materials and applications; amorphous and nanocrystalline magnetic materials and applications; hard magnetic materials; magnetic shape memory alloys; and magnetic oxides. The book's highly interdis...

Analysis of materials used for Greenhouse roof covering - structure using CFD

Science.gov (United States)

Subin, M. C.; Savio Lourence, Jason; Karthikeyan, Ram; Periasamy, C.

2018-04-01

Greenhouse is widely used to create a suitable environment for the growth of plant. During summer, high temperatures cause harm to the plant. This work calculates characteristics required to optimize the above-mentioned parameters using different roof structure covering materials for the greenhouse. Moreover, this work also presents a simulation of the cooling and heating system. In addition, a computer model based on Ansys Fluent has been using to predict the temperature profiles inside the greenhouse. Greenhouse roof structure shading may have a time-dependent effect the production, water and nutrient uptake in plants. An experiment was conducted in the emirate of Dubai in United Arab Emirates to discover the impact of different materials in order to have an optimal plant growth zone and yield production. These structures were poly ethylene and poly carbonate sheets of 2 different configurations. Results showed that poly carbonate sheets configuration of optimal thickness has given a high result in terms of yield production. Therefore, there is a need for appropriate material selection of greenhouse roof structure in this area of UAE. Major parameters and properties need to be considered while selecting a greenhouse roof structure are the resistance to solar radiation, weathering, thermal as well as mechanical properties and good abrasion resistance. In the present study, an experiment has been conducted to find out the material suitability of the greenhouse roof structure in terms of developing proper ambient conditions especially to minimize the energy lose by reducing the HVAC and lighting expenses. The configuration verified using the CFD, so it has been concluded that polycarbonate can be safely used in the greenhouse than other roof structure material having white or green colour.

Compilation of reports from research supported by the Materials Engineering Branch, Division of Engineering: 1965--1990

International Nuclear Information System (INIS)

Hiser, A.L.

1991-05-01

Since 1965, the Materials Engineering Branch, Division of Engineering, of the Nuclear Regulatory Commission's Office of Nuclear Regulatory Research, and its predecessors dating back to the Atomic Energy Commission (AEC), has sponsored research programs concerning the integrity of the primary system pressure boundary of light water reactors. The components of concern in these research programs have included the reactor pressure vessel (RPV), steam generators, and the piping. These research programs have covered a broad range of topics, including fracture mechanics analysis and experimental work for RPV and piping applications, inspection method development and qualification, and evaluation of irradiation effects to RPV steels. This report provides as complete a listing as practical of formal technical reports submitted to the NRC by the investigators working on these research programs. This listing includes topical, final and progress reports, and is segmented by topic area. In many cases a report will cover several topics (such as in the case of progress reports of multi-faceted programs), but is listed under only one topic. Therefore, in searching for reports on a specific topic, other related topic areas should be checked also

Teachers' opinion about learning continuum based on student's level of competence and specific pedagogical material in classification topics

Science.gov (United States)

Andriani, Aldina Eka; Subali, Bambang

2017-08-01

This research discusses learning continuum development for designing a curriculum. The objective of this study is to gather the opinion of public junior and senior high school teachers about learning continuum based on student's level of competence and specific pedagogical material in classification topics. This research was conducted in Yogyakarta province from October 2016 to January 2017. This research utilizes a descriptive survey method. Respondents in this study consist of 281 science teachers at junior and senior high school in Yogyakarta city and 4 regencies namely Sleman, Bantul, Kulonprogo, and Gunung Kidul. The sample were taken using a census. The collection of data used questionnaire that had been validated from the aspects of construct validity and experts judgements. Data were analyzed using a descriptive analysis technique. The results of the analysis show that the opinions of teachers regarding specific pedagogical material in classification topics of living things at the junior high school taught in grade VII to the ability level of C2 (Understanding). At senior high school level, it is taught in grade X with the ability level C2 (Understanding). Based on these results, it can be concluded that the opinions of teachers still refer to the current syllabus and curriculum so that the teachers do not have pure opinions about the student's competence level in classification topics that should be taught at the level of the grade in accordance with the level of corresponding competency.

Improving Elementary School Students’ English Vocabulary Through Local Cultural Content Materials

Directory of Open Access Journals (Sweden)

Frans Manurung

2015-06-01

Full Text Available Abstract Elementary students of a certain public school in Indonesia had difficulties in learning English. One of the crucial problems was learning English vocabulary. In an attempt to help the students learn and improve English vocabulary, the researchers decided to use CAR to teach English vocabulary with local cultural content materials. The aim of this study was to investigate how the teaching of English vocabulary with local cultural content materials contributed to the improvement of the students’ English vocabulary mastery. The topics covered in the materials were selected based on schemata theory. Vocabulary learning process was done through several activities provided in the materials: classroom and outside vocabulary learning. The results showed that the teaching of local cultural content materials have contributed to the improvement of the Elementary students’ vocabulary mastery. The schematic knowledge found in the familiar topics has aroused the students’ interest and motivation in learning English vocabulary. Students who were more familiar with the topics could respond to the vocabulary learning better than those who were not familiar with. The vocabulary mastery was more successful only if the students participated in both classroom and outside vocabulary learning process. Keywords: Vocabulary Mastery, Vocabulary Improvement, Local Cultural Content Materials, Vocabulary Learning, Schemata

Simulation of water flow and retention in earthen-cover materials overlying uranium mill tailings

International Nuclear Information System (INIS)

Simmons, C.S.; Gee, G.W.

1981-09-01

The water retention characteristics of a multilayer earthen cover for uranium mill tailings were simulated under arid weather conditions common to Grand Junction, Colorado. The multilayer system described in this report consists of a layer of wet clay/gravel (radon barrier), which is separated from a surface covering of fill soil by a washed rock material used as a capillary barrier. The capillary barrier is designed to prevent the upward migration of water and salt from the tailings to the soil surface and subsequent loss of water from the wet clay. The flow model, UNSATV, described in this report uses hydraulic properties of the layered materials and historical climatic data for two years (1976 and 1979) to simulate long-term hydrologic response of the multilayer system. Application of this model to simulate the processes of infiltration, evaporation and drainage is described in detail. Simulations over a trial period of one relatively wet and two dry years indicated that the clay-gravel layer remained near saturation, and hence, that the layer was an effective radon barrier. Estimates show that the clay-gravel layer would not dry out (i.e., revert to drying dominated by isothermal vapor-flow conditions) for at least 20 years, provided that the modeled dry-climate period continues

Progress and status of fusion technology and materials research in China

International Nuclear Information System (INIS)

Xu Zengyu; Liu Xiang; Chen Jiming; Zhang Fu

2003-01-01

Fusion technology and materials research in China was included in the National High Technology Project during 1986-2000. Since 2000, the National Natural Science Foundation Committee, the State Development Planning Commission, and the Ministry of Science and Technology have supported this field of research. The research program has covered the topics of tritium engineering, plasma facing materials and structural materials. The Southwestern Institute of Physics has been a leading institute in this research program in the last 15 years in China, and over ten universities and institutes have joined the program. (author)

Specialists' meeting on fast reactor cover gas purification

International Nuclear Information System (INIS)

1987-01-01

The tentative agenda was adopted by the participants without comment and was followed throughout the meeting. The following topics were discussed at the subsequent sessions of the meeting on 'Fast Reactor Cover Gas Purification': National Position Papers; Impurities: Sources and Measurement; Cover Gas Purification Techniques; Sodium Aerosol Trapping; Radiological Considerations. Based on the papers presented and the discussions following, session summaries and conclusions were prepared and are included in this report

Specialists' meeting on fast reactor cover gas purification

Energy Technology Data Exchange (ETDEWEB)

NONE

1987-07-01

The tentative agenda was adopted by the participants without comment and was followed throughout the meeting. The following topics were discussed at the subsequent sessions of the meeting on 'Fast Reactor Cover Gas Purification': National Position Papers; Impurities: Sources and Measurement; Cover Gas Purification Techniques; Sodium Aerosol Trapping; Radiological Considerations. Based on the papers presented and the discussions following, session summaries and conclusions were prepared and are included in this report.

Ion Implantation and Synthesis of Materials

CERN Document Server

Nastasi, Michael

2006-01-01

Ion implantation is one of the key processing steps in silicon integrated circuit technology. Some integrated circuits require up to 17 implantation steps and circuits are seldom processed with less than 10 implantation steps. Controlled doping at controlled depths is an essential feature of implantation. Ion beam processing can also be used to improve corrosion resistance, to harden surfaces, to reduce wear and, in general, to improve materials properties. This book presents the physics and materials science of ion implantation and ion beam modification of materials. It covers ion-solid interactions used to predict ion ranges, ion straggling and lattice disorder. Also treated are shallow-junction formation and slicing silicon with hydrogen ion beams. Topics important for materials modification, such as ion-beam mixing, stresses, and sputtering, are also described.

Topics to be covered in safety analysis reports for nuclear power plants with pressurized water reactors or boiling water reactors in the F.R.G

International Nuclear Information System (INIS)

Kohler, H.A.G.

1977-01-01

This manual aims at defining the standards to be used in Safety Analysis Reports for Nuclear Power Plants with Pressurized Water Reactors or Boiling Water Reactors in the Federal Republic of Germany. The topics to be covered are: Information about the site (geographic situation, settlement, industrial and military facilities, transport and communications, meteorological conditions, geological, hydrological and seismic conditions, radiological background), description of the power plant (building structures, safety vessel, reactor core, cooling system, ventilation systems, steam power plant, electrical facilities, systems for measurement and control), indication of operation (commissioning, operation, safety measures, radiation monitoring, organization), incident analysis (reactivity incidents, loss-of-coolant incidents, external impacts). (HP) [de

20 years of long-term water balance measurements of a landfill cover system with components constructed from pre-treated dredged material

NARCIS (Netherlands)

Berger, K.; Groengroeft, A.; Gebert, J.; Harms, C.; Eschenbach, A.

2017-01-01

The cover system of the mono-landfill Hamburg-Francop for disposal of dredged
material comprises a mineral liner of pre-treated fine-grained dredged material (‘METHAmaterial’) and an overlying drainage layer of pre-treated sandy dredged material (‘METHAsand’). Water balance and effectiveness of

ANS [American Nuclear Society] topical meeting on radiological accidents: Perspectives and emergency planning: Proceedings

International Nuclear Information System (INIS)

1987-03-01

The increasing use of radioactive materials and the increasing public concern about possible accidents involving these materials has led to greater emphasis on preparing for such emergencies. The ANS Topical Meeting on Radiological Accidents - Perspectives and Emergency Planning provided a review of experiences with radiological accidents. The meeting covered some of the most important aspects of radiological accidents. Papers were presented which dealt with radiological accident experience. Technical response to accidents is of primary interest to many in the nuclear community; most of the papers submitted fell into this area. So many of these papers dealt with the use of computers in response that a session on that topic was arranged. A very significant impact of most radiological accidents is the cost, especially the cost of cleanup. There were papers on what is known about costs and associated current topics, such as modification and extension of the Price-Anderson Act. At least as important as the technical response to accidents is how society attempts to deal with them. A session on institutional issues was included to discuss how governments and other organizations respond to and deal with accidents. Medical effects of accidents are of great concern to the public. Invited papers to review the effects of high doses of radiation as well as very low doses were included in that session. Although the nuclear industry has an excellent safety record, this fact often does not agree with the public perception of the industry. The final session explored the public response to and perception of radiological emergencies and accidents. This subject will ultimately determine the future use of radioactive materials in this country

Metal-molecular assembly for functional materials

CERN Document Server

Matsuo, Yutaka; Negishi, Yuichi; Yoshizawa, Michito; Uemura, Takashi; Takaya, Hikaru; Takeuchi, Masayuki; Yoshimoto, Soichiro

2013-01-01

This book focuses on modern coordination chemistry, covering porous coordination polymers, metalloproteins, metallopeptides, nanoclusters, nanocapsules, aligned polymers, and fullerenes. As well, it deals with applications to electronic devices and surface characterization. These wide-ranging topics are integrally described from the perspectives of dimensionality (one-, two-, and three-dimension), new materials design, synthesis, molecular assembly, function and application. The nine chapters making up this book have been authored by scientists who are at the cutting edge of research in this p

18th ICPR paper: Master Production Scheduling and A Comparision of Material Requirements Planning and Cover-Time Planning

OpenAIRE

2006-01-01

Abstract For a company?s long-term profitability, most important processes are the way it starts parts of the manufacturing process before the customer order arrives and the way it determines and promises delivery quantities and times for the customer orders. In practical computer applications Material Requirement Planning and/or Reorder point systems are the base techniques mostly used. This article pre?sents Cover-Time Planning, a variant of a reorder point system. Cover-Time Pla...

International Conference on Materials, Processing and Product Engineering 2015 (MPPE2015)

International Nuclear Information System (INIS)

Eck, S; Ebner, R; Ludwig, A

2016-01-01

The Materials Center Leoben Forschung GmbH (MCL) and the Austrian Society for Metallurgy and Materials (ASMET) have jointly organized the 'First International Conference on Materials, Processing and Product Engineering - MPPE' held in the Congress Center of Leoben from Nov. 3 rd to 5 th , 2015. The main topic of the conference was to present the state of the art in fundamental knowledge and technological expertise enabling and stimulating the development of knowledge based innovations across the entire product value chain starting from the material synthesis, proceeding with the processing of products and concluding with their in-service behaviour until the end of the product life time. Hence, the International Conference on Materials, Processing and Product Engineering MPPE 2015 focused on the core regions of industrial production chains, covering topics such as • Development and characterization of materials; • Materials synthesis and processing; • Dimensioning of components including integrated materials and process modelling; • Behaviour of materials and components during service. The scientific and technological goal was to present the state of the art of theoretical, experimental and numerical techniques and their combinations that are capable of improving the competitiveness of modern production facilities. (paper)

Bone Regeneration after Treatment with Covering Materials Composed of Flax Fibers and Biodegradable Plastics: A Histological Study in Rats.

Science.gov (United States)

Gredes, Tomasz; Kunath, Franziska; Gedrange, Tomasz; Kunert-Keil, Christiane

2016-01-01

The aim of this study was to examine the osteogenic potential of new flax covering materials. Bone defects were created on the skull of forty rats. Materials of pure PLA and PCL and their composites with flax fibers, genetically modified producing PHB (PLA-transgen, PCL-transgen) and unmodified (PLA-wt, PCL-wt), were inserted. The skulls were harvested after four weeks and subjected to histological examination. The percentage of bone regeneration by using PLA was less pronounced than after usage of pure PCL in comparison with controls. After treatment with PCL-transgen, a large amount of new formed bone could be found. In contrast, PCL-wt decreased significantly the bone regeneration, compared to the other tested groups. The bone covers made of pure PLA had substantially less influence on bone regeneration and the bone healing proceeded with a lot of connective tissue, whereas PLA-transgen and PLA-wt showed nearly comparable amount of new formed bone. Regarding the histological data, the hypothesis could be proposed that PCL and its composites have contributed to a higher quantity of the regenerated bone, compared to PLA. The histological studies showed comparable bone regeneration processes after treatment with tested covering materials, as well as in the untreated bone lesions.

Bone Regeneration after Treatment with Covering Materials Composed of Flax Fibers and Biodegradable Plastics: A Histological Study in Rats

Directory of Open Access Journals (Sweden)

Tomasz Gredes

2016-01-01

Full Text Available The aim of this study was to examine the osteogenic potential of new flax covering materials. Bone defects were created on the skull of forty rats. Materials of pure PLA and PCL and their composites with flax fibers, genetically modified producing PHB (PLA-transgen, PCL-transgen and unmodified (PLA-wt, PCL-wt, were inserted. The skulls were harvested after four weeks and subjected to histological examination. The percentage of bone regeneration by using PLA was less pronounced than after usage of pure PCL in comparison with controls. After treatment with PCL-transgen, a large amount of new formed bone could be found. In contrast, PCL-wt decreased significantly the bone regeneration, compared to the other tested groups. The bone covers made of pure PLA had substantially less influence on bone regeneration and the bone healing proceeded with a lot of connective tissue, whereas PLA-transgen and PLA-wt showed nearly comparable amount of new formed bone. Regarding the histological data, the hypothesis could be proposed that PCL and its composites have contributed to a higher quantity of the regenerated bone, compared to PLA. The histological studies showed comparable bone regeneration processes after treatment with tested covering materials, as well as in the untreated bone lesions.

Bone Regeneration after Treatment with Covering Materials Composed of Flax Fibers and Biodegradable Plastics: A Histological Study in Rats

Science.gov (United States)

Gedrange, Tomasz

2016-01-01

The aim of this study was to examine the osteogenic potential of new flax covering materials. Bone defects were created on the skull of forty rats. Materials of pure PLA and PCL and their composites with flax fibers, genetically modified producing PHB (PLA-transgen, PCL-transgen) and unmodified (PLA-wt, PCL-wt), were inserted. The skulls were harvested after four weeks and subjected to histological examination. The percentage of bone regeneration by using PLA was less pronounced than after usage of pure PCL in comparison with controls. After treatment with PCL-transgen, a large amount of new formed bone could be found. In contrast, PCL-wt decreased significantly the bone regeneration, compared to the other tested groups. The bone covers made of pure PLA had substantially less influence on bone regeneration and the bone healing proceeded with a lot of connective tissue, whereas PLA-transgen and PLA-wt showed nearly comparable amount of new formed bone. Regarding the histological data, the hypothesis could be proposed that PCL and its composites have contributed to a higher quantity of the regenerated bone, compared to PLA. The histological studies showed comparable bone regeneration processes after treatment with tested covering materials, as well as in the untreated bone lesions. PMID:27597965

Topics in Bioethics: A Development of Student Perspectives

Directory of Open Access Journals (Sweden)

Keith A. Johnson

2014-10-01

Full Text Available Exposing students to current biotechnological and medical issues is eye-opening for many students in a way that is not always achieved through lecture-based learning. Lecture or investigative teaching styles provide a tremendous knowledge base for the students, but sometimes these teaching styles do not allow the student to fully develop, especially personal attitudes to issues in bioethics. Through online videos, Hollywood movies, guided readings and classroom discussions, students in this course are informed of some bioethical topics, encouraged to learn about other topics, and use this gained knowledge to develop personal positions regarding the value and/or risk of the issues. This course has been well-received by previous students as a favorite in terms of both topics covered and style.

Escalation of terrorism? On the risk of attacks with chemical, biological, radiological and nuclear weapons or materials

International Nuclear Information System (INIS)

Nass, Jens

2010-01-01

The report on the risk of attacks with chemical, biological, radiological and nuclear weapons or materials covers the following topics: the variety of terrorism: ethnic-nationalistic, politically motivated, social revolutionary, political extremism, religious fanaticism, governmental terrorism; CBRN (chemical, biological, radiological, nuclear) weapons and materials: their availability and effectiveness in case of use; potential actor groups; prevention and counter measures, emergency and mitigating measures.

Design review report, 241-S-102 cover plate review; TOPICAL

International Nuclear Information System (INIS)

ADAMS, M.R.

1998-01-01

The design for the cover plate and lead plate for shielding on 241-S-102 was reviewed on 10/21/98. All Review Comment Record comments were resolved to the satisfaction of the reviewers. Additional comments were taken during the meeting and were also resolved. A design calculation for the Radiological Design Review Screening was presented as criteria for the use of 1 inch lead plate. The review concluded that the use of 2 inch steel plate and 1 inch lead plate provided the required safety function required by HNF-SD-WM-810-001, 5.3.2.20, Basis for Interim Operation. The design was approved with the incorporated comments as recorded on RCR's and meeting minutes

Optimal Covering Material for Stent-Grafts Placed in the Portal Vein in a Canine Model

International Nuclear Information System (INIS)

Ishii, Seigo; Sato, Morio; Sonomura, Tetsuo; Yamada, Katsuyuki; Tanihata, Hirohiko; Ishikawa, Hime; Terada, Masaki; Sahara, Shinya; Kawai, Nobuyuki; Kimura, Masashi; Mori, Ichiro

2005-01-01

Purpose. We evaluated the suitability of Dacron, polytetrafluoroethylene (PTFE), and small intestinal submucosa (SIS) as a covering material for stent-grafts placed in the portal vein as compared with a bare stent. Methods. Using 24 beagle dogs, either bare stents or stent-grafts covered with Dacron, PTFE, or SIS were placed in the main trunk of the portal vein in 6 animals each. Portography was performed immediately after stent placement, and at 2, 4, and 12 weeks thereafter. Next, the extracted stents or stent-grafts were examined histopathologically. Neointimal thickness adjacent to the stent wire and at the midportion between the stent wires was compared among the groups. Then, the neointimal thickness at the sub- and supragraft sites was compared between each stent-graft group. Serial changes in the histologic features of the thickened neointima were also investigated. Results. No significant difference was noted in the mean stenotic ratio of the portal vein diameter between the bare stent and PTFE groups, whereas it was significantly higher in the Dacron and SIS groups compared with the bare stent group. In neither of the studies on neointimal thickness adjacent to the stent wire and at the midportion between the stent wires were any significant differences noted between the neointimal thickness of the bare stent group and the sum of the neointimal thickness of the PTFE group, whereas the sum of the neointimal thickness of the Dacron and SIS groups was significantly greater than that of the bare stent group at both sites. In the comparison of the supragraft neointimal thickness, the SIS group showed significantly greater thickness than the PTFE group, while the difference between the Dacron and PTFE groups was not significant. In the comparison of the subgraft neointimal thickness, the Dacron and SIS groups showed significantly greater thickness than the PTFE group. Conclusion. The present results indicate that of the three covering materials examined here

Frontiers of ferroelectricity a special issue of the journal of materials science

CERN Document Server

Lang, Sidney B

2007-01-01

The book presents theory, fundamentals and some applications of ferroelectricy. The 24 chapters comprise reviews and research reports covering the spectrum of ferroelectricity. It is intended to describe the current levels of understanding of various aspects of ferroelectricity as presented by authorities in the field. Topics include relaxors, piezoelectrics, microscale and nanoscale studies, polymers and composites, unusual properties, and techniques and devices. The information in this book is intended for physicists, engineers and materials scientists working with ferroelectric materials including ceramics, single crystals, polymers, composites and even some biological materials.

Nanotechnology-enhanced orthopedic materials fabrications, applications and future trends

CERN Document Server

Yang, Lei

2015-01-01

Nanotechnology-Enhanced Orthopedic Materials provides the latest information on the emergence and rapid development of nanotechnology and the ways it has impacted almost every aspect of biomedical engineering. This book provides readers with a comprehensive overview of the field, focusing on the fabrication and applications of these materials, presenting updated, practical, and systematic knowledge on the synthesis, processing, and modification of nanomaterials, along with the rationale and methodology of applying such materials for orthopedic purposes. Topics covered include a wide range of orthopedic material formulations, such as ceramics, metals, polymers, biomolecules, and self-assemblies. Final sections explore applications and future trends in nanotechnology-enhanced orthopedic materials. Details practical information on the fabrication and modification of new and traditional orthopedic materials Analyzes a wide range of materials, designs, and applications of nanotechnology for orthopedics Investigate...

Proceedings of the second international conference on advances in nuclear materials: abstract booklet and souvenir

International Nuclear Information System (INIS)

2011-01-01

Nuclear materials form special class of materials which either act as fuel for the nuclear reactors or form the structure of the reactors and the allied systems. The topics covered in this conference are: materials challenges for thermal and fast reactors, technological advances in nuclear fuels and components, materials for future reactors, fuel cycles and materials challenges, materials degradation and life management, advanced materials development, modelling and simulation, advanced materials- II, advanced materials for future reactors, development of advanced fuel and structural materials, zirconium alloy developments, irradiation effects and PIE, advanced nuclear fuels, corrosion and materials characterization. Papers relevant to INIS are indexed separately

Nuclear material control and accounting safeguards in the United States

International Nuclear Information System (INIS)

Woltermann, H.A.; Rudy, C.R.; Rakel, D.A.; DeVer, E.A.

1982-01-01

Material control and accounting (MC and A) of special nuclear material (SNM) must supplement physical security to protect SNM from unlawful use such as terrorist activities. This article reviews MC and A safeguards of SNM in the United States. The following topics are covered: a brief perspective and history of MC and A safeguards, current MC and A practices, measurement methods for SNM, historical MC and A performance, a description of near-real-time MC and A systems, and conclusions on the status of MC and A in the United States

Solid electrolytes general principles, characterization, materials, applications

CERN Document Server

Hagenmuller, Paul

1978-01-01

Solid Electrolytes: General Principles, Characterization, Materials, Applications presents specific theories and experimental methods in the field of superionic conductors. It discusses that high ionic conductivity in solids requires specific structural and energetic conditions. It addresses the problems involved in the study and use of solid electrolytes. Some of the topics covered in the book are the introduction to the theory of solid electrolytes; macroscopic evidence for liquid nature; structural models; kinetic models; crystal structures and fast ionic conduction; interstitial motion in

Modern topics in electron scattering

CERN Document Server

Frois, Bernard

1991-01-01

This book summarizes the considerable progress recently achieved in the understanding of nucleon and nuclear structure by using high energy electrons as a probe. A collection of papers discusses in detail the new frontiers of this field. Experimental and theoretical articles cover topics such as the structure of the nucleon, nucleon distributions, many-body correlations, non-nucleonic degrees of freedom and few-body systems. This book is an up-to-date introduction to the research planned with continuous beam electron accelerators.

Proceedings of the first international conference on indium phosphide and related materials for advanced electronic and optical devices

International Nuclear Information System (INIS)

Singh, R.; Messick, L.J.

1989-01-01

This book contains the proceedings of the first international conference on indium phosphide and related materials for advanced electronic and optical devices. Topics covered include: Growth and characterization of bulk and epitaxial films, Passivation technology, Processing technology, High speed optoelectronic integrated circuits, and Solar cells

The development of learning materials based on core model to improve students’ learning outcomes in topic of Chemical Bonding

Science.gov (United States)

Avianti, R.; Suyatno; Sugiarto, B.

2018-04-01

This study aims to create an appropriate learning material based on CORE (Connecting, Organizing, Reflecting, Extending) model to improve students’ learning achievement in Chemical Bonding Topic. This study used 4-D models as research design and one group pretest-posttest as design of the material treatment. The subject of the study was teaching materials based on CORE model, conducted on 30 students of Science class grade 10. The collecting data process involved some techniques such as validation, observation, test, and questionnaire. The findings were that: (1) all the contents were valid, (2) the practicality and the effectiveness of all the contents were good. The conclusion of this research was that the CORE model is appropriate to improve students’ learning outcomes for studying Chemical Bonding.

Antimicrobial topical agents used in the vagina.

Science.gov (United States)

Frey Tirri, Brigitte

2011-01-01

Vaginally applied antimicrobial agents are widely used in the vagina in women with lower genital tract infections. An 'antimicrobial' is a general term that refers to a group of drugs that are effective against bacteria, fungi, viruses and protozoa. Topical treatments can be prescribed for a wide variety of vaginal infections. Many bacterial infections, such as bacterial vaginosis, desquamative inflammatory vaginitis or, as some European authors call it, aerobic vaginitis as well as infection with Staphylococcus aureus or group A streptococci, may be treated in this way. Candida vulvovaginitis is a fungal infection that is very amenable to topical treatment. The most common viral infections which can be treated with topical medications are condylomata acuminata and herpes simplex. The most often encountered protozoal vaginitis, which is caused by Trichomonas vaginalis, may be susceptible to topical medications, although this infection is treated systemically. This chapter covers the wide variety of commonly used topical antimicrobial agents for these diseases and focuses on the individual therapeutic agents and their clinical efficacy. In addition, potential difficulties that can occur in practice, as well as the usage of these medications in the special setting of pregnancy, are described in this chapter. Copyright © 2011 S. Karger AG, Basel.

[The effects of topical fluoridation of Ketac Molar Aplicap glass-ionomer material on the growth of cariogenic bacteria contained in the dental plaque].

Science.gov (United States)

Płuciennik-Stronias, Małgorzata; Zarzycka, Beata; Bołtacz-Rzepkowska, Elzbieta

2013-01-01

Dental caries is a bacterial disease. The most important element used in caries prevention is fluoride, which is derived from the air, diet or fluoride-containing preparations and materials, e.g. glass-ionomer restorations. Modern fluoride-containing restorative materials are capable of releasing fluoride to the environment. Fluoride can be also accumulated in glass-ionomer cements, thus an attempt was made to saturate these materials with fluoride. The aim of the study was to evaluate the effect of topical fluoridation of Ketac Molar Aplicap glass-ionomer cement on the growth of Lactobacillus spp. in the dental plaque. The study was carried out in 15 patients with good oral hygiene, in whom 35 fillings with conventional glass-ionomer material, Ketac Molar Aplicap, were performed. After 6 months, three-day dental plaque from these fillings was examined. Next, fluoride was rubbed on the glass-ionomer surface and the examination of three-day dental plaque was repeated. No statistically significant differences (p = 0.143) in the amounts of Lactobacillus spp. in the plaque collected prior to and after topical fluoridation were revealed. Fluoride rubbed in the conventional glass-ionomer cement, Ketac Molar Aplicap, did not affect the amount of Lactobacillus spp. in the dental plaque growing on this material.

Topical reports on Louisiana salt domes

International Nuclear Information System (INIS)

1983-09-01

The Institute for Environmental Studies at Louisiana State University conducted research into the potential use of Louisiana salt domes for disposal of nuclear waste material. Topical reports generated in 1981 and 1982 related to Vacherie and Rayburn's domes are compiled and presented, which address palynological studies, tiltmeter monitoring, precise releveling, saline springs, and surface hydrology. The latter two are basically a compilation of references related to these topics. Individual reports are abstracted

Topical papers on raw materials

International Nuclear Information System (INIS)

1978-01-01

In the papers of this working group, the availability of uranium and the long-term supply situation for this raw material are discussed. A problem closely connected with uranium supply are the commercial contracts and their particularities. The points of view of the reporting countries of Great Britain, South Africa, Switzerland, Australia, Japan, and Korea are made clear

Analyzing research trends on drug safety using topic modeling.

Science.gov (United States)

Zou, Chen

2018-04-06

Published drug safety data has evolved in the past decade due to scientific and technological advances in the relevant research fields. Considering that a vast amount of scientific literature has been published in this area, it is not easy to identify the key information. Topic modeling has emerged as a powerful tool to extract meaningful information from a large volume of unstructured texts. Areas covered: We analyzed the titles and abstracts of 4347 articles in four journals dedicated to drug safety from 2007 to 2016. We applied Latent Dirichlet allocation (LDA) model to extract 50 main topics, and conducted trend analysis to explore the temporal popularity of these topics over years. Expert Opinion/Commentary: We found that 'benefit-risk assessment and communication', 'diabetes' and 'biologic therapy for autoimmune diseases' are the top 3 most published topics. The topics relevant to the use of electronic health records/observational data for safety surveillance are becoming increasingly popular over time. Meanwhile, there is a slight decrease in research on signal detection based on spontaneous reporting, although spontaneous reporting still plays an important role in benefit-risk assessment. The topics related to medical conditions and treatment showed highly dynamic patterns over time.

XRF analysis of ceramics, minerals and allied materials

International Nuclear Information System (INIS)

Bennett, H.; Oliver, G.J.

1992-01-01

This book is a compilation of practical information on the X-ray fluorescence analysis by the fused, cast bead method of mineral type materials and products. A range of general information about equipment and apparatus and its use and care is given and particular attention is devoted to the spectrometer and the topic of line selection. Experimental details of the method, including calibration, are presented. In the final section of the book, analytical procedures for a wide range of materials are described. This includes sampling, drying, weighing, loss on ignition, fusion, casting, constituents to be determined, calibration ranges and reporting of results. The materials covered are silica/alumina range materials, calcium-rich materials, magnesium rich materials, zircon-bearing materials, various oxides and titanates, reduced materials and samples of unknown composition. The appendices contain data on loss on ignition techniques, specific fusion techniques, problem elements or oxides, certified references materials and details on laboratory accreditation. (UK)

Bulk Materials Analysis Using High-Energy Positron Beams

International Nuclear Information System (INIS)

Glade, S C; Asoka-Kumar, P; Nieh, T G; Sterne, P A; Wirth, B D; Dauskardt, R H; Flores, K M; Suh, D; Odette, G.R.

2002-01-01

This article reviews some recent materials analysis results using high-energy positron beams at Lawrence Livermore National Laboratory. We are combining positron lifetime and orbital electron momentum spectroscopic methods to provide electron number densities and electron momentum distributions around positron annihilation sites. Topics covered include: correlation of positron annihilation characteristics with structural and mechanical properties of bulk metallic glasses, compositional studies of embrittling features in nuclear reactor pressure vessel steel, pore characterization in Zeolites, and positron annihilation characteristics in alkali halides

Topical nonsteroidal anti-inflammatory drugs for the treatment of pain due to soft tissue injury: diclofenac epolamine topical patch.

Science.gov (United States)

Lionberger, David R; Brennan, Michael J

2010-11-10

The objective of this article is to review published clinical data on diclofenac epolamine topical patch 1.3% (DETP) in the treatment of acute soft tissue injuries, such as strains, sprains, and contusions. Review of published literature on topical nonsteroidal anti-inflammatory drugs (NSAIDs), diclofenac, and DETP in patients with acute soft tissue injuries was included. Relevant literature was identified on MEDLINE using the search terms topical NSAIDs, diclofenac, diclofenac epolamine, acute pain, sports injury, soft tissue injury, strain, sprain, and contusion, and from citations in retrieved articles covering the years 1978-2008. Review of published, randomized clinical trials and meta-analyses shows that topical NSAIDs are significantly more effective than placebo in relieving acute pain; the pooled average relative benefit was 1.7 (95% confidence interval, 1.5-1.9). In a limited number of comparisons, topical and oral NSAIDs provided comparable pain relief, but the use of topical agents produced lower plasma drug concentrations and fewer systemic adverse events (AEs). The physical-chemical properties of diclofenac epolamine make it well suited for topical use. In patients with acute soft tissue injuries treated with DETP, clinical data report an analgesic benefit within hours of the first application, and significant pain relief relative to placebo within 3 days. Moreover, DETP displayed tolerability comparable with placebo; the most common AEs were pruritus and other application site reactions. Review of published literature suggests that DETP is generally safe and well tolerated, clinically efficacious, and a rational treatment option for patients experiencing acute pain associated with strains, sprains, and contusions, and other localized painful conditions.

Materials science and technology strained-layer superlattices materials science and technology

CERN Document Server

Pearsall, Thomas P; Willardson, R K; Pearsall, Thomas P

1990-01-01

The following blurb to be used for the AP Report and ATI only as both volumes will not appear together there.****Strained-layer superlattices have been developed as an important new form of semiconducting material with applications in integrated electro-optics and electronics. Edited by a pioneer in the field, Thomas Pearsall, this volume offers a comprehensive discussion of strained-layer superlattices and focuses on fabrication technology and applications of the material. This volume combines with Volume 32, Strained-Layer Superlattices: Physics, in this series to cover a broad spectrum of topics, including molecular beam epitaxy, quantum wells and superlattices, strain-effects in semiconductors, optical and electrical properties of semiconductors, and semiconductor devices.****The following previously approved blurb is to be used in all other direct mail and advertising as both volumes will be promoted together.****Strained-layer superlattices have been developed as an important new form of semiconducting ...

Recent advances in mass transport in materials

CERN Document Server

Ochsner, Andreas

2012-01-01

The present topical volume presents a representative cross-section of some recent advances made in the area of diffusion. The range of topics covered is very large, and, this reflects the enormous breadth of the topic of diffusion. The areas covered include diffusion in intermetallics, phenomenological diffusion theory, diffusional creep, kinetics of steel-making, diffusion in thin films, precipitation, diffusional phase transformations, atomistic diffusion simulations, epitaxial growth and diffusion in porous media. Review from Book News Inc.: In 13 invited and peer-reviewed papers, scientist

Understanding Materials Science History · Properties · Applications

CERN Document Server

Hummel, Rolf E

2005-01-01

This introduction to materials science both for students of engineering and physics and for the interested general public examines not only the physical and engineering properties of virtually all kinds of materials, but also their history, uses, development, and some of the implications of resource depletion and recycling. It covers all topics on materials from an entirely novel perspective: the role materials have played throughout history in the development of humankind and technologies. Specifically, it shows the connection between the technical and the cultural, economic, ecological, and societal aspects of materials science. It aims to whet the appetite of its readers and inspire them to further explore the properties and applications of metals, alloys, ceramics, plastics, and electronic materials by presenting easily understandable explanations and entertaining historical facts. It is also intended to raise the reader’s awareness of their obligations to society as practicing engineers and scientists....

Topics in algebra and analysis preparing for the mathematical olympiad

CERN Document Server

Bulajich Manfrino, Radmila; Valdez Delgado, Rogelio

2015-01-01

The techniques presented here are useful for solving mathematical contest problems in algebra and analysis. Most of the examples and exercises that appear in the book originate from mathematical Olympiad competitions around the world. In the first four chapters the authors cover material for competitions at high school level. The level advances with the chapters. The topics explored include polynomials, functional equations, sequences and an elementary treatment of complex numbers. The final chapters provide a comprehensive list of problems posed at national and international contests in recent years, and solutions to all exercises and problems presented in the book. It helps students in preparing for national and international mathematical contests form high school level to more advanced competitions and will also be useful for their first year of mathematical studies at the university. It will be of interest to teachers in college and university level, and trainers of the mathematical Olympiads.

Interrelationships between soil cover and plant cover depending on land use

Directory of Open Access Journals (Sweden)

Tiina Köster

2013-05-01

Full Text Available Interrelationships between soil cover and plant cover of normally developed (or postlithogenic mineral soils are analysed on the basis of four sampling soil groups. The four-link pedo-ecological sequence of analysed soils, rendzinas → brown soils → pseudopodzolic soils → gley-podzols, forms a representative cross section in relation to the normal mineral soils of Estonia. All groups differ substantially from each other in terms of soil properties (calcareousness, acidity, nutrition conditions, profile fabric and humus cover. The primary tasks of the research were (1 to elucidate the main pedo-ecological characteristics of the four soil groups and their suitability for plant cover, (2 to evaluate comparatively soils in terms of productivity, sustainability, biodiversity and environmental protection ability and (3 to analyse possibilities for ecologically sound matching of soil cover with suitable plant cover. On the basis of the same material, the influence of land-use change on humus cover (epipedon fabric, properties of the entire soil cover and soil–plant interrelationship were also analysed. An ecosystem approach enables us to observe particularities caused by specific properties of a soil type (species, variety in biological turnover and in the formation of biodiversity.

Medical adherence to topical corticosteroid preparations prescribed for psoriasis

DEFF Research Database (Denmark)

Svendsen, Mathias Tiedemann; Andersen, Flemming; Hansen, Jakob

2017-01-01

OBJECTIVE: Topical corticosteroids and corticosteroid combinations are the principal treatments in psoriasis. The aim of this study was to investigate published literature dealing with medical adherence to topical corticosteroid or corticosteroid combinations in patients with psoriasis. MATERIALS...... health outcome in topical treatment of psoriasis, further studies should be conducted addressing determinants of nonadherence and test interventions to improve adherence. Validated measurements of medical nonadherence, prescription registers, or medication-weight are needed....

Topical nonsteroidal anti-inflammatory drugs for the treatment of pain due to soft tissue injury: diclofenac epolamine topical patch

Directory of Open Access Journals (Sweden)

David R Lionberger

2010-11-01

Full Text Available David R Lionberger1, Michael J Brennan21Southwest Orthopedic Group, Houston, TX, USA; 2Department of Medicine, Bridgeport Hospital, Bridgeport, CT, USAAbstract: The objective of this article is to review published clinical data on diclofenac epolamine topical patch 1.3% (DETP in the treatment of acute soft tissue injuries, such as strains, sprains, and contusions. Review of published literature on topical nonsteroidal anti-inflammatory drugs (NSAIDs, diclofenac, and DETP in patients with acute soft tissue injuries was included. Relevant literature was identified on MEDLINE using the search terms topical NSAIDs, diclofenac, diclofenac epolamine, acute pain, sports injury, soft tissue injury, strain, sprain, and contusion, and from citations in retrieved articles covering the years 1978–2008. Review of published, randomized clinical trials and meta-analyses shows that topical NSAIDs are significantly more effective than placebo in relieving acute pain; the pooled average relative benefit was 1.7 (95% confidence interval, 1.5–1.9. In a limited number of comparisons, topical and oral NSAIDs provided comparable pain relief, but the use of topical agents produced lower plasma drug concentrations and fewer systemic adverse events (AEs. The physical–chemical properties of diclofenac epolamine make it well suited for topical use. In patients with acute soft tissue injuries treated with DETP, clinical data report an analgesic benefit within hours of the first application, and significant pain relief relative to placebo within 3 days. Moreover, DETP displayed tolerability comparable with placebo; the most common AEs were pruritus and other application site reactions. Review of published literature suggests that DETP is generally safe and well tolerated, clinically efficacious, and a rational treatment option for patients experiencing acute pain associated with strains, sprains, and contusions, and other localized painful conditions

Topics in radiation dosimetry radiation dosimetry

CERN Document Server

1972-01-01

Radiation Dosimetry, Supplement 1: Topics in Radiation Dosimetry covers instruments and techniques in dealing with special dosimetry problems. The book discusses thermoluminescence dosimetry in archeological dating; dosimetric applications of track etching; vacuum chambers of radiation measurement. The text also describes wall-less detectors in microdosimetry; dosimetry of low-energy X-rays; and the theory and general applicability of the gamma-ray theory of track effects to various systems. Dose equivalent determinations in neutron fields by means of moderator techniques; as well as developm

Studies of volatiles and organic materials in early terrestrial and present-day outer solar system environments

Science.gov (United States)

Sagan, Carl; Thompson, W. Reid; Chyba, Christopher F.; Khare, B. N.

1991-01-01

A review and partial summary of projects within several areas of research generally involving the origin, distribution, chemistry, and spectral/dielectric properties of volatiles and organic materials in the outer solar system and early terrestrial environments are presented. The major topics covered include: (1) impact delivery of volatiles and organic compounds to the early terrestrial planets; (2) optical constants measurements; (3) spectral classification, chemical processes, and distribution of materials; and (4) radar properties of ice, hydrocarbons, and organic heteropolymers.

Device and materials modeling in PEM fuel cells

CERN Document Server

Promislow, Keith

2009-01-01

Device and Materials Modeling in PEM Fuel Cells is a specialized text that compiles the mathematical details and results of both device and materials modeling in a single volume. Proton exchange membrane (PEM) fuel cells will likely have an impact on our way of life similar to the integrated circuit. The potential applications range from the micron scale to large scale industrial production. Successful integration of PEM fuel cells into the mass market will require new materials and a deeper understanding of the balance required to maintain various operational states. This book contains articles from scientists who contribute to fuel cell models from both the materials and device perspectives. Topics such as catalyst layer performance and operation, reactor dynamics, macroscopic transport, and analytical models are covered under device modeling. Materials modeling include subjects relating to the membrane and the catalyst such as proton conduction, atomistic structural modeling, quantum molecular dynamics, an...

Land-cover change detection

Science.gov (United States)

Chen, Xuexia; Giri, Chandra; Vogelmann, James

2012-01-01

Land cover is the biophysical material on the surface of the earth. Land-cover types include grass, shrubs, trees, barren, water, and man-made features. Land cover changes continuously.  The rate of change can be either dramatic and abrupt, such as the changes caused by logging, hurricanes and fire, or subtle and gradual, such as regeneration of forests and damage caused by insects (Verbesselt et al., 2001).  Previous studies have shown that land cover has changed dramatically during the past sevearal centuries and that these changes have severely affected our ecosystems (Foody, 2010; Lambin et al., 2001). Lambin and Strahlers (1994b) summarized five types of cause for land-cover changes: (1) long-term natural changes in climate conditions, (2) geomorphological and ecological processes, (3) human-induced alterations of vegetation cover and landscapes, (4) interannual climate variability, and (5) human-induced greenhouse effect.  Tools and techniques are needed to detect, describe, and predict these changes to facilitate sustainable management of natural resources.

Handbook of damage mechanics nano to macro scale for materials and structures

CERN Document Server

2015-01-01

This authoritative reference provides comprehensive coverage of the topics of damage and healing mechanics. Computational modeling of constitutive equations is provided as well as solved examples in engineering applications. A wide range of materials that engineers may encounter are covered, including metals, composites, ceramics, polymers, biomaterials, and nanomaterials. The internationally recognized team of contributors employ a consistent and systematic approach, offering readers a user-friendly reference that is ideal for frequent consultation. Handbook of Damage Mechanics: Nano to Macro Scale for Materials and Structures is ideal for graduate students and faculty, researchers, and professionals in the fields of Mechanical Engineering, Civil Engineering, Aerospace Engineering, Materials Science, and Engineering Mechanics.

Topical Melatonin for Treatment of Androgenetic Alopecia

OpenAIRE

Fischer, Tobias W; Tr?eb, Ralph M; H?nggi, Gabriella; Innocenti, Marcello; Elsner, Peter

2012-01-01

Background: In the search for alternative agents to oral finasteride and topical minoxidil for the treatment of androgenetic alopecia (AGA), melatonin, a potent antioxidant and growth modulator, was identified as a promising candidate based on in vitro and in vivo studies. Materials and Methods: One pharmacodynamic study on topical application of melatonin and four clinical pre-post studies were performed in patients with androgenetic alopecia or general hair loss and evaluated by standardise...

Leaves of knowledge, a collectable publication for dissemination of scientific and technological topics

International Nuclear Information System (INIS)

Spurio, S. M.

2013-01-01

The Institute of Energy and Sustainable Development (IEDS) of the National Atomic Energy Commission of Argentina performs an active task of popularization of nuclear science and technology applications and its spin-off activities. The IEDS, based on this goal and the known expression of Descartes 'Science branches intertwine in the Tree of Knowledge' has been making the annual task of inviting authors, editing, publishing and often, printing the publication Leaves of Knowledge, since 2008 and without interruption. The presentation format consists in a holder folder containing collectibles sheets. Each sheet represents a leaf on the Tree Science Knowledge. The publication encourages the participation of renowned professionals invited from CNEA and other Institutions who are committing to writing just two pages of their topic specialty. As to the fifth edition currently being edited, 56 items have already been published on the following seven general topics: ENVIRONMENT - APPLICATIONS - SCIENCE - ENERGY - MATERIALS - HEALTH - SAFETY. Although it was originally aimed to the general public, now it has evolved into three distinct approaches also covering universitary and professional level. Its PDF version is available to the public through the IEDS website and it was registered under its corresponding ISBN. (author)

Safe transport of radioactive material. 3. ed

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-12-01

The IAEA has developed a standardized approach to transport safety training as a means of helping Member States to implement the Transport Regulations. The training manual is an anchor of this standardized approach to training: it contains all the topics presented in the sequential order recommended by the IAEA for the student to gain a thorough understanding of the body of knowledge that is needed to ensure that radioactive material ranked as Class 7 in the United Nations' nomenclature for dangerous goods - is transported safely. The explanations in the text refer, where needed, to the appropriate requirements in the IAEA's Transport Regulations; additional useful information is also provided. Thus, the training manual in addition to the Transport Regulations and their supporting documents is used by the IAEA as the basis for delivering all of its training courses on the safe transport of radioactive material. Enclosed with the training manual is a CD-ROM that contains the text of the manual as well as the visual aids that are used at the IAEA's training courses. The following topics are covered: review of radioactivity and radiation; review of radiation protection principles; regulatory terminology; basic safety concepts: materials and packages; activity limits and material restrictions; selection of optimal package type; test procedures: material and packages; requirements for transport; control of material in transport; fissile material: regulatory requirements and operational aspects; quality assurance; national competent authority; additional regulatory constraints for transport; international liability and insurance; emergency planning and preparedness; training; services provided by the IAEA.

Safe transport of radioactive material. 3. ed

International Nuclear Information System (INIS)

2002-01-01

The IAEA has developed a standardized approach to transport safety training as a means of helping Member States to implement the Transport Regulations. The training manual is an anchor of this standardized approach to training: it contains all the topics presented in the sequential order recommended by the IAEA for the student to gain a thorough understanding of the body of knowledge that is needed to ensure that radioactive material ranked as Class 7 in the United Nations' nomenclature for dangerous goods - is transported safely. The explanations in the text refer, where needed, to the appropriate requirements in the IAEA's Transport Regulations; additional useful information is also provided. Thus, the training manual in addition to the Transport Regulations and their supporting documents is used by the IAEA as the basis for delivering all of its training courses on the safe transport of radioactive material. Enclosed with the training manual is a CD-ROM that contains the text of the manual as well as the visual aids that are used at the IAEA's training courses. The following topics are covered: review of radioactivity and radiation; review of radiation protection principles; regulatory terminology; basic safety concepts: materials and packages; activity limits and material restrictions; selection of optimal package type; test procedures: material and packages; requirements for transport; control of material in transport; fissile material: regulatory requirements and operational aspects; quality assurance; national competent authority; additional regulatory constraints for transport; international liability and insurance; emergency planning and preparedness; training; services provided by the IAEA

Recent advances and perspectives in topical oral anesthesia.

Science.gov (United States)

Franz-Montan, Michelle; Ribeiro, Lígia Nunes de Morais; Volpato, Maria Cristina; Cereda, Cintia Maria Saia; Groppo, Francisco Carlos; Tofoli, Giovana Randomille; de Araújo, Daniele Ribeiro; Santi, Patrizia; Padula, Cristina; de Paula, Eneida

2017-05-01

Topical anesthesia is widely used in dentistry to reduce pain caused by needle insertion and injection of the anesthetic. However, successful anesthesia is not always achieved using the formulations that are currently commercially available. As a result, local anesthesia is still one of the procedures that is most feared by dental patients. Drug delivery systems (DDSs) provide ways of improving the efficacy of topical agents. Areas covered: An overview of the structure and permeability of oral mucosa is given, followed by a review of DDSs designed for dental topical anesthesia and their related clinical trials. Chemical approaches to enhance permeation and anesthesia efficacy, or to promote superficial anesthesia, include nanostructured carriers (liposomes, cyclodextrins, polymeric nanoparticle systems, solid lipid nanoparticles, and nanostructured lipid carriers) and different pharmaceutical dosage forms (patches, bio- and mucoadhesive systems, and hydrogels). Physical methods include pre-cooling, vibration, iontophoresis, and microneedle arrays. Expert opinion: The combination of different chemical and physical methods is an attractive option for effective topical anesthesia in oral mucosa. This comprehensive review should provide the readers with the most relevant options currently available to assist pain-free dental anesthesia. The findings should be considered for future clinical trials.

AMNT 2014. Key topic: Reactor operation, safety - report. Pt. 2

International Nuclear Information System (INIS)

Fischer, Klaus-Christian; Willschuetz, Hans-Georg; Wortmann, Birgit

2014-01-01

Summary report on the following sessions of the Annual Conference on Nuclear Technology held in Frankfurt, 6 to 8 May 2014: - Thermo Dynamics and Fluid Dynamics: Experiments and Backfittings for the Improvement of Safety and Efficiency; - Safety of Nuclear Installations - Methods, Analyses, Results: In-Vessel Phenomena; Ex-Vessel Phenomena; - Standards and Regulations; Hazard and Safety Analysis; and Validation and Uncertainty Analysis. The other Sessions of the Key Topics 'Reactor Operation, Safety', 'Competence, Innovation, Regulation' and 'Fuel, Decommissioning and Disposal' have been covered in atw 10 (2014) and will be covered in further issues of atw.

AMNT 2014. Key topic: Reactor operation, safety - report. Pt. 3

Energy Technology Data Exchange (ETDEWEB)

Bohnstedt, Angelika [Karlsruher Institut fuer Technologie (KIT), Eggenstein-Leopoldshafen (Germany). Programm Nukleare Sicherheitsforschung (NUKLEAR); Mull, Thomas [AREVA GmbH, Erlangen (Germany). Nuclear Fusion, HTR and Transverse Issues (PTDH-G); Starflinger, Joerg [Stuttgart Univ. (Germany). Inst. fuer Kernenergetik und Energiesysteme (IKE)

2015-01-15

Summary report on the following sessions of the Annual Conference on Nuclear Technology held in Frankfurt, 6 to 8 May 2014: - Reactor Operation, Safety: Radiation Protection (Angelika Bohnstedt); - Competence, Innovation, Regulation: Fusion Technology - Optimisation Steps in the ITER Design (Thomas Mull); - Competence, Innovation, Regulation: Education, Expert Knowledge, Knowledge Transfer (Joerg Starflinger). The other Sessions of the Key Topics 'Reactor Operation, Safety', 'Competence, Innovation, Regulation' and 'Fuel, Decommissioning and Disposal' have been covered in atw 10 and 12 (2015) and will be covered in further issues of atw.

Interdisciplinary Student/Teacher Materials in Energy, the Environment, and the Economy: 6, The Energy We Use, Grade 1.

Science.gov (United States)

Bloch, Lenore; And Others

This instructional unit contains a set of nine lessons on energy for grade one. Each lesson contains complete teacher and student materials. Reading skills and language experiences are reinforced in each activity. The lessons cover such topics as energy from food, energy from the sun, fossil fuels, the wind, moving water, and energy conservation.…

Topics in Finance Part I--Introduction and Stockholder Wealth Maximization

Science.gov (United States)

Laux, Judy

2010-01-01

The following article represents the first in a series dedicated to presenting students the opportunity to better understand the key theoretical constructs in the introductory financial management course. The current essay offers an introduction to the series and covers the topics of stockholder wealth maximization and its close cousin, agency…

Recent topics in NMR imaging and MRI

International Nuclear Information System (INIS)

Watanabe, Tokuko

2002-01-01

NMR and NMR imaging (MRI) are finding increasing use not only in the clinical and medical fields, but also in material, physicochemical, biological, geological, industrial and environmental applications. This short review is limited to two topics: new techniques and pulse sequences and their application to non-clinical fields that may have clinical application; and new trends in MR contrast agents. The former topic addresses pulse sequence and data analysis; dynamics such as diffusion, flow, velocity and velocimetry; chemometrics; pharmacological agents; and chemotherapy; the latter topic addresses contrast agents (CA) sensitive to biochemical activity; CA based on water exchange; molecular interactions and stability of CA; characteristics of emerging CA; superparamagnetic CA; and macromolecular CA. (author)

Fusion materials semiannual progress report for period ending June 30, 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-08-01

This is the twenty-second in a series of semiannual technical progress reports on fusion materials. This report combines the full spectrum of research and development activities on both metallic and non-metallic materials with primary emphasis on the effects of the neutronic and chemical environment on the properties and performance of materials for in-vessel components. This effort forms one element of the materials program being conducted in support of the Fusion Energy Sciences Program of the US Department of Energy. The other major element of the program is concerned with the interactions between reactor materials and the plasma and is reported separately. Topics covered here are: vanadium alloys; silicon carbide composites; ferritic/martensitic steels; austenitic stainless steels; insulating ceramics and optical materials; solid breeding materials; radiation effects mechanistic studies and experimental methods; dosimetry damage parameters; activation calculations; materials engineering and design requirements; irradiation facilities; test matrices; and experimental methods.

Fusion materials semiannual progress report for period ending June 30, 1997

International Nuclear Information System (INIS)

1997-08-01

This is the twenty-second in a series of semiannual technical progress reports on fusion materials. This report combines the full spectrum of research and development activities on both metallic and non-metallic materials with primary emphasis on the effects of the neutronic and chemical environment on the properties and performance of materials for in-vessel components. This effort forms one element of the materials program being conducted in support of the Fusion Energy Sciences Program of the US Department of Energy. The other major element of the program is concerned with the interactions between reactor materials and the plasma and is reported separately. Topics covered here are: vanadium alloys; silicon carbide composites; ferritic/martensitic steels; austenitic stainless steels; insulating ceramics and optical materials; solid breeding materials; radiation effects mechanistic studies and experimental methods; dosimetry damage parameters; activation calculations; materials engineering and design requirements; irradiation facilities; test matrices; and experimental methods

Topical Session on the Decommissioning and Dismantling Safety Case

International Nuclear Information System (INIS)

2002-01-01

Set up by the Radioactive Waste Management Committee (RWMC), the WPDD brings together senior representatives of national organisations who have a broad overview of Decommissioning and Dismantling (D and D) issues through their work as regulators, implementers, R and D experts or policy makers. These include representatives from regulatory authorities, industrial decommissioners from the NEA Cooperative Programme on Exchange of Scientific and Technical Information on Nuclear Installation Decommissioning Projects (CPD), and cross-representation from the NEA Committee on Nuclear Regulatory Activities, the Committee on Radiation Protection and Public Health, and the RWMC. The EC is a member of the WPDD and the IAEA also participates. This ensures co-ordination amongst activities in these international programmes. Participation from civil society organisations is considered on a case by case basis, and has already taken place through the active involvement of the Group of Municipalities with Nuclear Installations at the first meeting of the WPDD At its second meeting, in Paris, 5-7 December 2001, the WPDD held two topical sessions on the D and D Safety Case and on the Management of Materials from D and D, respectively. This report documents the topical session on the safety case. The topical session was meant to provide an exchange of information and experience on the following issues: What topics should be included in a safety case? Of what should it consist? Is there sufficient and complete guidance nationally and internationally? How do practices differ internationally? Main boundary condition to this session was that it would deal with plants where spent fuel has been removed. Also the topical sessions was kept at a level that makes the most of the varied constituency of the WPDD. Namely, interface issues are important, and issue-identification and discussion was the immediate goal. There was less interest in examining areas where variability amongst national

A Water Balance Study of Four Landfill Cover Designs at Material Disposal Area B in Los Alamos, New Mexico

Energy Technology Data Exchange (ETDEWEB)

David D. Breshears; Fairley J. Barnes; John W. Nyhan; Johnny A. Salazar

1998-09-01

The goal of disposing of low-level radioactive and hazardous waste in shallow landfills is to reduce risk to human health and the environment by isolating contaminants until they no longer pose an unacceptable hazard. In order to achieve this, the Department of Energy Environmental Restoration Program is comparing the performance of several different surface covers at Material Disposal Area (MDA) B in Los Alamos. Two conventional landfill were compared with an improved cover designed to minimize plant and animal intrusion and to minimize water infiltration into the underlying wastes. The conventional covers varied in depth and both conventional and improved designs had different combinations of vegetation (grass verses shrub) and gravel mulch (no mulch verses mulch). These treatments were applied to each of 12 plots and water balance parameters were measured from March1987 through June 1995. Adding a gravel mulch significantly influenced the plant covered field plots receiving no gravel mulch averaged 21.2% shrub cover, while plots with gravel had a 20% larger percent cover of shrubs. However, the influence of gravel mulch on the grass cover was even larger than the influence on shrub cover, average grass cover on the plots with no gravel was 16.3%, compared with a 42% increase in grass cover due to gravel mulch. These cover relationships are important to reduce runoff on the landfill cover, as shown by a regression model that predicts that as ground cover is increased from 30 to 90%,annual runoff is reduced from 8.8 to 0.98 cm-a nine-fold increase. We also found that decreasing the slope of the landfill cover from 6 to 2% reduced runoff from the landfill cover by 2.7-fold. To minimize the risk of hazardous waste from landfills to humans, runoff and seepage need to be minimized and evapotranspiration maximized on the landfill cover. This has to be accomplished for dry and wet years at MDA B. Seepage consisted of 1.9% and 6.2% of the precipitation in the average and

Materials of jubilee scientific assembly of the Polish Chemical Society, Warsaw'94. Homo chemicus

International Nuclear Information System (INIS)

1994-01-01

The Jubilee Scientific Assembly of the Polish Chemical Society has been held in 1994 in Warsaw. The general view on scientific progress in chemistry in Poland has been presented during plenary session. The conference has been divided into 15 sessions and 3 microsymposia covering the most important research fields in chemistry. Sessions topics were: analytical chemistry, chemistry of solid state materials, physical chemistry, coordination chemistry, medical chemistry, chemistry of metalorganic compounds, inorganic chemistry, organic chemistry, chemistry of polymers, young scientists forum, didactics and history of chemistry, catalysis, crystallochemistry, chemical technology, environment protection. Microsymposia's topics were as follows: chemistry of saccharides, electrochemistry, membranes and membrane processes

Topical Session on Liabilities identification and long-term management at national level - Topical Session held during the 36. Meeting of the RWMC

International Nuclear Information System (INIS)

2003-01-01

These proceedings cover a topical session that was held at the March 2003 meeting of the Radioactive Waste Management Committee. The topical session focused on liability assessment and management for decommissioning of all types of nuclear installations, including decontamination of historic sites and waste management, as applicable. The presentations covered the current, national situations. The first oral presentation, from Switzerland, set the scene by providing a broad coverage of the relevant issues. The subsequent presentations - five from Member countries and one from the EC - described additional national positions and the evolving EC proposed directives. Each oral presentation was followed by a brief period of Q and As for clarification only. A plenary discussion took place on the ensemble of presentations and a Rapporteur provided a report on points made and lessons learnt. Additionally, written contributions were provided by RWMC delegates from several other countries. These are included in the proceedings as are the papers from the oral sessions, and the Rapporteur's report. These papers are not intended to be exhaustive, but to give an informed glimpse of NEA countries' approaches to liability identification and management in the context of nuclear facilities decommissioning and dismantling

Topics in cement and concrete research

NARCIS (Netherlands)

Brouwers, Jos; Russel, M.I.; Basheer, P.A.M.

2007-01-01

The present paper addresses several topics in regard to the sustainable design and use of concrete. First, major features concerning the sustainable aspects of the material concrete are summarised. Then the major constituent, from an environmental point of view, cement is discussed in detail,

Second biennial tri-laboratory engineering conference on modeling and simulation

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

This conference was divided into eight sessions. Session one covered the following topics: material behavior and characterization; computation heat transfer; computational fluid dynamics; and hydrodynamics. Topics covered in session two were: structural dynamics; manufacturing process modeling; solid and structural mechanics; and electromagnetics. Session three topics were: materials behavior and characterization; computational heat transfer; computational fluid dynamics; neutron generators and gas transfer systems applications. Topics for session four were: mesh generation and visualization; validation and verification; and pit manufacturing. Session five covered the following: ALE techniques and applications; solid and structural mechanical; and system applications. The three topics of session six were: optimization methods; manufacturing process modeling; and weapon response in hostile environments. Session covered: material behavior and characterization; computational heat transfer; solid and structural mechanics; and mesh generation and visualization. And finally, the topics of session 8 were: manufacturing and process modeling; solid and structural mechanics; uncertainty analysis; and structural dynamics. Paper covered a range of applications, many of which were weapons and weapon systems.

Topics and topic prominence in two sign languages

NARCIS (Netherlands)

Kimmelman, V.

2015-01-01

In this paper we describe topic marking in Russian Sign Language (RSL) and Sign Language of the Netherlands (NGT) and discuss whether these languages should be considered topic prominent. The formal markers of topics in RSL are sentence-initial position, a prosodic break following the topic, and

Safety and Health Topics: Lead

Science.gov (United States)

... ammunition, pipes, cable covering, building material, solder, radiation shielding, collapsible tubes, and fishing weights. Lead is also ... lead linings in tanks and radiation protection, leaded glass, work involving soldering, and other work involving lead ...

Safety of transport of radioactive material. Contributed papers

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-07-01

Radioactive material has been transported for decades within and between countries as the use of radioactive material to benefit mankind has expanded. The transport can involve many types of materials (radionuclides and radiation sources for applications in agriculture, energy production, industry, and medicine) and all modes of transport (road, rail, sea and waterways, and air). Among the organizations in the United Nations system, the International Atomic Energy Agency (IAEA) has the statutory function to establish or adopt standards of safety for protection of health against exposure to ionizing radiation. Within its statutory mandate and pursuant to this request, in 1961, the IAEA issued Regulations for the Safe Transport of Radioactive Material (the IAEA Transport Regulations). The Transport Regulations were periodically reviewed and, as appropriate, have been amended or revised. The latest version of the Transport Regulations was issued in 2000 by the IAEA as Publication TS-R-1 (ST-1, Revised). In addition, the IAEA is entrusted by its Statute to provide for the application of its standards at the request of States. The objective of the Conference is to foster the exchange of information on issues related to the safety of transport of radioactive material by providing an opportunity for representatives from sponsoring international organizations and their Member States and from other co-operating and participating organizations to discuss critical issues relating to the safety of transport of radioactive material by all modes and to formulate recommendations, as appropriate, regarding further international co-operation in this area. The following topics have been identified by the Technical Programme Committee as the subjects to be covered in the background briefing sessions: History and Status of the IAEA Transport Regulation Development; Experience in adoption of the IAEA Transport Regulations at the international level; Implementation of the IAEA Transport

Materials and nanotechnology

International Nuclear Information System (INIS)

2014-01-01

The focus of the Materials and Nanotechnology Program is technology development related to processing, analysis, testing and characterization of materials in general. These are achieved through execution of R&D projects in engineering and materials science, cooperative projects with private and public sector companies, universities and other research institutes. Besides technology development, this Program also fosters training and human resource development in association with the University of São Paulo and many industrial sectors. This Program is divided into sub-programs in broad areas such as ceramic, composite and metallic materials as well as characterization of physical and chemical properties of materials. The sub-programs are further divided into general topics and within each topic, R&D projects. A brief description of progress in each topic during the last three years follows. (author)

Is cost-covering remuneration fully booked? - Teething problems

International Nuclear Information System (INIS)

Niederhaeusern, A.

2009-01-01

In this interview with Michael Kaufmann, director of the SwissEnergy programme, possible strategies for the correct pricing of electricity and measures for the correction of the dissatisfactory situation now prevailing concerning the cost-covering remuneration of power from renewable sources are discussed. The pricing of electricity from various sources and the indirect costs that are at present not met by non-renewable resources are commented on. Further topics covered include suggestions for strategies for relieving the presently blocked financial promotion of renewables, the goals set for the role to be played by renewable energy in Swiss electricity production in 2030 and suggestions for future political action

Advancing materials research

International Nuclear Information System (INIS)

Langford, H.D.; Psaras, P.A.

1987-01-01

The topics discussed in this volume include historical perspectives in the fields of materials research and development, the status of selected scientific and technical areas, and current topics in materials research. Papers are presentd on progress and prospects in metallurgical research, microstructure and mechanical properties of metals, condensed-matter physics and materials research, quasi-periodic crystals, and new and artifically structured electronic and magnetic materials. Consideration is also given to materials research in catalysis, advanced ceramics, organic polymers, new ways of looking at surfaces, and materials synthesis and processing

What Patients Can Tell Us: Topic Analysis for Social Media on Breast Cancer.

Science.gov (United States)

Tapi Nzali, Mike Donald; Bringay, Sandra; Lavergne, Christian; Mollevi, Caroline; Opitz, Thomas

2017-07-31

Social media dedicated to health are increasingly used by patients and health professionals. They are rich textual resources with content generated through free exchange between patients. We are proposing a method to tackle the problem of retrieving clinically relevant information from such social media in order to analyze the quality of life of patients with breast cancer. Our aim was to detect the different topics discussed by patients on social media and to relate them to functional and symptomatic dimensions assessed in the internationally standardized self-administered questionnaires used in cancer clinical trials (European Organization for Research and Treatment of Cancer [EORTC] Quality of Life Questionnaire Core 30 [QLQ-C30] and breast cancer module [QLQ-BR23]). First, we applied a classic text mining technique, latent Dirichlet allocation (LDA), to detect the different topics discussed on social media dealing with breast cancer. We applied the LDA model to 2 datasets composed of messages extracted from public Facebook groups and from a public health forum (cancerdusein.org, a French breast cancer forum) with relevant preprocessing. Second, we applied a customized Jaccard coefficient to automatically compute similarity distance between the topics detected with LDA and the questions in the self-administered questionnaires used to study quality of life. Among the 23 topics present in the self-administered questionnaires, 22 matched with the topics discussed by patients on social media. Interestingly, these topics corresponded to 95% (22/23) of the forum and 86% (20/23) of the Facebook group topics. These figures underline that topics related to quality of life are an important concern for patients. However, 5 social media topics had no corresponding topic in the questionnaires, which do not cover all of the patients' concerns. Of these 5 topics, 2 could potentially be used in the questionnaires, and these 2 topics corresponded to a total of 3.10% (523

Strategic raw materials. Risk management; Strategische Rohstoffe. Risikovorsorge

Energy Technology Data Exchange (ETDEWEB)

Bertau, Martin [Technische Univ. Bergakademie Freiberg (Germany). Inst. fuer Technische Chemie; Gutzmer, Jens [Helmholtz-Institut fuer Ressourcentechnologie Freiberg (Germany); Matschullat, Joerg (ed.) [Technische Univ. Bergakademie Freiberg (Germany). Interdisziplinaeres Oekologisches Zentrum (IOeZ); Kausch, Peter

2014-07-01

This volume is divided into four chapters: (1) Raw material management, (2) Primary raw materials, (3) Secondary raw materials and recycling, (4). Processing and products. The topics for the chapter ''Raw material management'' are: Substitution of raw materials - framework conditions and implementation; Thales: Strategic raw materials; Time for cooperation between the EU and China in raw materials policy; Availability of elements for the semiconductor industry; Market price risks of raw material-intensive companies - identification and management. The topics on the second item ''Primary raw materials'' are: The supply of economic-critical raw materials - A search and analysis for causes; Lithium extraction from primary raw materials - state and perspectives; The global market of rare earths - A balancing act; Rare earth deposits in Namibia; New technologies in exploration and discovery - Focus on activities in Europe. The third chapter, ''Secondary Raw Materials and Recycling'', covered the topics: Technology metals - Systemic Requirements along the recycling chain; Integrated re-use of high-tech and greentech wastes; From the sewage sludge ash to the phosphorus fertilizer RecoPhos P38 in the stress field of waste, fertilizer and soil protection. In chapter 4. ''Processing and products'' are the topics: Treatment and processing of rare earth metals; Processing of mineral resources - opportunities and challenges; Consequences of modern germanium chemistry; Strategic resources - Risk management. A review and outlook with a pinch of fantasy.. [German] Dieser Band gliedert sich in vier Kapitel: (1) Rohstoffwirtschaft, (2) Primaere Rohstoffe, (3) Sekundaere Rohstoffe und Recycling,(4). Verarbeitung und Produkte. Die Themen zum Kapitel ''Rohstoffwirtschaft'' sind: Substitution von Rohstoffen - Rahmenbedingungen und Umsetzung; Thales: Strategische Rohstoffe; Zeit fuer

Farm Water Supply and Sanitation--Pipe, Plumbing, Skills and Symbols. Student Materials. V.A. III. V-D-1, V-D-2.

Science.gov (United States)

Texas A and M Univ., College Station. Vocational Instructional Services.

Designed for use by individuals enrolled in vocational agricultural classes, these student materials deal with farm water supply, sanitation, and plumbing skills. Topics covered in the unit are maintaining the farm water supply; repairing faucets and valves, leaks in pipes and storage tanks, and water closets; clearing clogged drains and traps;…

Assessing alternative measures of tree canopy cover: Photo-interpreted NAIP and ground-based estimates

Science.gov (United States)

Chris Toney; Greg Liknes; Andy Lister; Dacia Meneguzzo

2012-01-01

In preparation for the development of the National Land Cover Database (NLCD) 2011 tree canopy cover layer, a pilot project for research and method development was completed in 2010 by the USDA Forest Service Forest Inventory and Analysis (FIA) program and Remote Sensing Applications Center (RSAC).This paper explores one of several topics investigated during the NLCD...

First Responders Guide to Computer Forensics: Advanced Topics

National Research Council Canada - National Science Library

Nolan, Richard; Baker, Marie; Branson, Jake; Hammerstein, Josh; Rush, Kris; Waits, Cal; Schweinsberg, Elizabeth

2005-01-01

First Responders Guide to Computer Forensics: Advanced Topics expands on the technical material presented in SEI handbook CMU/SEI-2005-HB-001, First Responders Guide to Computer Forensics [Nolan 05...

#Healthy Selfies: Exploration of Health Topics on Instagram.

Science.gov (United States)

Muralidhara, Sachin; Paul, Michael J

2018-06-29

Social media provides a complementary source of information for public health surveillance. The dominate data source for this type of monitoring is the microblogging platform Twitter, which is convenient due to the free availability of public data. Less is known about the utility of other social media platforms, despite their popularity. This work aims to characterize the health topics that are prominently discussed in the image-sharing platform Instagram, as a step toward understanding how this data might be used for public health research. The study uses a topic modeling approach to discover topics in a dataset of 96,426 Instagram posts containing hashtags related to health. We use a polylingual topic model, initially developed for datasets in different natural languages, to model different modalities of data: hashtags, caption words, and image tags automatically extracted using a computer vision tool. We identified 47 health-related topics in the data (kappa=.77), covering ten broad categories: acute illness, alternative medicine, chronic illness and pain, diet, exercise, health care & medicine, mental health, musculoskeletal health and dermatology, sleep, and substance use. The most prevalent topics were related to diet (8,293/96,426; 8.6% of posts) and exercise (7,328/96,426; 7.6% of posts). A large and diverse set of health topics are discussed in Instagram. The extracted image tags were generally too coarse and noisy to be used for identifying posts but were in some cases accurate for identifying images relevant to studying diet and substance use. Instagram shows potential as a source of public health information, though limitations in data collection and metadata availability may limit its use in comparison to platforms like Twitter. ©Sachin Muralidhara, Michael J. Paul. Originally published in JMIR Public Health and Surveillance (http://publichealth.jmir.org), 29.06.2018.

Nanocrystal: a novel approach to overcome skin barriers for improved topical drug delivery.

Science.gov (United States)

Patel, Viral; Sharma, Om Prakash; Mehta, Tejal

2018-04-01

Skin is an important route of drug delivery for the treatment of various dermatological conditions. The advent of nanotechnology is paving the roadmaps for topical drug delivery by providing sustained release as well as maintaining a localized effect, outweighing the toxicity concern. Area covered: This review highlighted the morphology of skin, its barrier nature as well as drug penetration pathways after topical application of formulations. The existing methods to improve topical drug delivery, by infringing or permeating the skin barriers, are discussed. This context concretes the foundation to accentuate the need for the development of nanocrystal-based topical formulation. The mechanism of drug release, immediate as well as sustained release, after topical administration of drug nanocrystals is also elaborated. The special emphasis is given on the breakthrough achieved, in topical drug delivery using drug nanocrystals, so far in the plethora of literature, patents, and products, under clinical trial as well as in the market. Expert opinion: The current research on nanocrystals for topical drug delivery is highlighting the breakthroughs achieved so far. The output of these research envisages that topical nanocrystals based formulations can be a novel strategy for the drugs which are facing solubility, bioavailability and toxicity concerns.

Ultrasonic spectroscopy applications in condensed matter physics and materials science

CERN Document Server

Leisure, Robert G

2017-01-01

Ultrasonic spectroscopy is a technique widely used in solid-state physics, materials science, and geology that utilizes acoustic waves to determine fundamental physical properties of materials, such as their elasticity and mechanical energy dissipation. This book provides complete coverage of the main issues relevant to the design, analysis, and interpretation of ultrasonic experiments. Topics including elasticity, acoustic waves in solids, ultrasonic loss, and the relation of elastic constants to thermodynamic potentials are covered in depth. Modern techniques and experimental methods including resonant ultrasound spectroscopy, digital pulse-echo, and picosecond ultrasound are also introduced and reviewed. This self-contained book includes extensive background theory and is accessible to students new to the field of ultrasonic spectroscopy, as well as to graduate students and researchers in physics, engineering, materials science, and geophysics.

Fusion materials semiannual progress report for the period ending December 31, 1996

International Nuclear Information System (INIS)

1997-04-01

This is the twenty-first in a series of semiannual technical progress reports on fusion materials. This report combines the full spectrum of research and development activities on both metallic and non-metallic materials with primary emphasis on the effects of the neutronic and chemical environment on the properties and performance of materials for in-vessel components. This effort forms one element of the materials program being conducted in support of the Fusion Energy Sciences Program of the US Department of Energy. The other major element of the program is concerned with the interactions between reactor materials and the plasma and is reported separately. The report covers the following topics: vanadium alloys; silicon carbide composite materials; ferritic/martensitic steels; copper alloys and high heat flux materials; austenitic stainless steels; insulating ceramics and optical materials; solid breeding materials; radiation effects, mechanistic studies and experimental methods; dosimetry, damage parameters, and activation calculations; materials engineering and design requirements; and irradiation facilities, test matrices, and experimental methods

Fusion materials semiannual progress report for the period ending December 31, 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-04-01

This is the twenty-first in a series of semiannual technical progress reports on fusion materials. This report combines the full spectrum of research and development activities on both metallic and non-metallic materials with primary emphasis on the effects of the neutronic and chemical environment on the properties and performance of materials for in-vessel components. This effort forms one element of the materials program being conducted in support of the Fusion Energy Sciences Program of the US Department of Energy. The other major element of the program is concerned with the interactions between reactor materials and the plasma and is reported separately. The report covers the following topics: vanadium alloys; silicon carbide composite materials; ferritic/martensitic steels; copper alloys and high heat flux materials; austenitic stainless steels; insulating ceramics and optical materials; solid breeding materials; radiation effects, mechanistic studies and experimental methods; dosimetry, damage parameters, and activation calculations; materials engineering and design requirements; and irradiation facilities, test matrices, and experimental methods.

UMTRAP research on cover design for uranium mill tailings

International Nuclear Information System (INIS)

Rogers, V.C.; Nielson, K.K.

1984-01-01

As a result of the UMTRAP research on radon attenuation and tailings cover design, the basis and general procedures are available for designing covers for uranium tailings piles to meet present criteria for radon emissions. The general procedures involve assessment of the radon source strength of the tailings, definition of candidate cover materials, assessment of their moisture retention and radon diffusion properties, computing the required thicknesses of these materials, comparing costs, and evaluating long-term performance criteria. Final selection of the cover design must assure adequate long-term performance and radon retention as first priority, and keep costs to a minimum in achieving this goal

Satellite DNA: An Evolving Topic.

Science.gov (United States)

Garrido-Ramos, Manuel A

2017-09-18

Satellite DNA represents one of the most fascinating parts of the repetitive fraction of the eukaryotic genome. Since the discovery of highly repetitive tandem DNA in the 1960s, a lot of literature has extensively covered various topics related to the structure, organization, function, and evolution of such sequences. Today, with the advent of genomic tools, the study of satellite DNA has regained a great interest. Thus, Next-Generation Sequencing (NGS), together with high-throughput in silico analysis of the information contained in NGS reads, has revolutionized the analysis of the repetitive fraction of the eukaryotic genomes. The whole of the historical and current approaches to the topic gives us a broad view of the function and evolution of satellite DNA and its role in chromosomal evolution. Currently, we have extensive information on the molecular, chromosomal, biological, and population factors that affect the evolutionary fate of satellite DNA, knowledge that gives rise to a series of hypotheses that get on well with each other about the origin, spreading, and evolution of satellite DNA. In this paper, I review these hypotheses from a methodological, conceptual, and historical perspective and frame them in the context of chromosomal organization and evolution.

Beneficiation and extraction of nonterrestrial materials, part 2

Science.gov (United States)

Agosto, William N.

A review of options for processing extraterrestrial materials was dominated by industrial materials scientist who tried to identify which processes utilizing space materials could be implemented in the near term. The most practical process seem to us to be the extraction of lunar oxygen and the extraction of metals and ceramics from the residues of the reduction process. The growth of space activity will be accompanied by increased demand for liquid oxygen for each round trip to the Moon. The oxygen and the intermediary product water will be needed for the life support at the base. The reduced metals and ceramics may be considered byproducts or may develop into primary products. Some of the same processes would be directly applicable to recovery of products from asteroids. We also discussed other processes for directly utilizing asteroid metals. Some of the topics covered include beneficiation and oxygen extraction methods, metallurgy, and extraterrestrial cement.

AMNT 2014. Key Topic: Reactor operation, safety - report. Pt. 1

International Nuclear Information System (INIS)

Schaffrath, Andreas

2014-01-01

Summary report on one session of the Annual Conference on Nuclear Technology held in Frankfurt, 6 to 8 May 2014: - Safety of Nuclear Installations - Methods, Analysis, Results: Backfittings for the Improvement of Safety and Efficiency. The other Sessions of the Key Topics 'Reactor Operation, Safety', 'Competence, Innovation, Regulation' and 'Fuel, Decommissioning and Disposal' will be covered in further issues of atw.

Development of drainage water quality from a landfill cover built with secondary construction materials.

Science.gov (United States)

Travar, Igor; Andreas, Lale; Kumpiene, Jurate; Lagerkvist, Anders

2015-01-01

The aim of this study was to evaluate the drainage water quality from a landfill cover built with secondary construction materials (SCM), fly ash (FA), bottom ash (BA) sewage sludge, compost and its changes over time. Column tests, physical simulation models and a full scale field test were conducted. While the laboratory tests showed a clear trend for all studied constituents towards reduced concentrations over time, the concentrations in the field fluctuated considerably. The primary contaminants in the drainage water were Cl(-), N, dissolved organic matter and Cd, Cu, Ni, Zn with initial concentrations one to three orders of magnitude above the discharge values to the local recipient. Using a sludge/FA mixture in the protection layer resulted in less contaminated drainage water compared to a sludge/BA mixture. If the leaching conditions in the landfill cover change from reduced to oxidized, the release of trace elements from ashes is expected to last about one decade longer while the release of N and organic matter from the sludge can be shortened with about two-three decades. The observed concentration levels and their expected development over time require drainage water treatment for at least three to four decades before the water can be discharged directly to the recipient. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Climate under cover

CERN Document Server

Takakura, Tadashi

2002-01-01

1.1. INTRODUCTION Plastic covering, either framed or floating, is now used worldwide to protect crops from unfavorable growing conditions, such as severe weather and insects and birds. Protected cultivation in the broad sense, including mulching, has been widely spread by the innovation of plastic films. Paper, straw, and glass were the main materials used before the era of plastics. Utilization of plastics in agriculture started in the developed countries and is now spreading to the developing countries. Early utilization of plastic was in cold regions, and plastic was mainly used for protection from the cold. Now plastic is used also for protection from wind, insects and diseases. The use of covering techniques started with a simple system such as mulching, then row covers and small tunnels were developed, and finally plastic houses. Floating mulch was an exception to this sequence: it was introduced rather recently, although it is a simple structure. New development of functional and inexpensive films trig...

Alternative cover design

International Nuclear Information System (INIS)

1988-11-01

The special study on Alternative Cover Designs is one of several studies initiated by the US Department of Energy (DOE) in response to the proposed US Environmental Protection Agency (EPA) groundwater standards. The objective of this study is to investigate the possibility of minimizing the infiltration of precipitation through stabilized tailings piles by altering the standard design of covers currently used on the Uranium Mill Tailings Remedial Action (UMTRA) Project. Prior. to the issuance of the proposed standards, UMTRA Project piles had common design elements to meet the required criteria, the most important of which were for radon diffusion, long-term stability, erosion protection, and groundwater protection. The standard pile covers consisted of three distinct layers. From top to bottom they were: rock for erosion protection; a sand bedding layer; and the radon barrier, usually consisting of a clayey sand material, which also functioned to limit infiltration into the tailings. The piles generally had topslopes from 2 to 4 percent and sideslopes of 20 percent

Preface to 18. Chemnitz seminar on materials engineering

International Nuclear Information System (INIS)

2016-01-01

The Institute of Materials Science and Engineering (Institut für Werkstoffwissenschaft und Werkstofftechnik, IWW) is a well-established part of the Faculty of Mechanical Engineering at Technische Universität Chemnitz, Germany. We are proud to host our traditional scientific meeting, the Chemnitz Seminar on Materials Engineering - Werkstofftechnisches Kolloquium, this year being the 18 th Seminar. The aim of our meeting is to bring together scientists and engineers both from academia and industry, and this is reflected by the different scientific sessions that cover various relevant topics, such as composite materials, microstructural analysis, and surface engineering. Special focus sessions highlight recent developments in the Federal Cluster of Excellence MERGE and in the Collaborative Research Center SFB 692, both established in Chemnitz. We, as organizers, continuously strive to improve our Seminar, and we therefore decided to provide all contributors with the opportunity to publish their papers, in addition to the printed Proceedings volume, in an international, peer-reviewed journal. Publication in IOP Conference Series: Materials Science and Engineering allows for a wide dissemination of the many interesting and relevant results presented in our Seminar. Clearly, this is understood and appreciated by many participants of our meeting: more than 65% of all authors chose to also publish their Proceedings papers in this special issue, which consequently provides an excellent overview of the main topics of our Seminar. Chemnitz, March 2016 Prof. Thomas Lampke Prof. Guntram Wagner Prof. Martin F.-X. Wagner (paper)

Preface to Special Topic: Marine Renewable Energy

Energy Technology Data Exchange (ETDEWEB)

Pinto, F. T.; Iglesias, G.; Santos, P. R.; Deng, Zhiqun

2015-12-30

Marine renewable energy (MRE) is generates from waves, currents, tides, and thermal resources in the ocean. MRE has been identified as a potential commercial-scale source of renewable energy. This special topic presents a compilation of works selected from the 3rd IAHR Europe Congress, held in Porto, Portugal, in 2014. It covers different subjects relevant to MRE, including resource assessment, marine energy sector policies, energy source comparisons based on levelized cost, proof-of-concept and new-technology development for wave and tidal energy exploitation, and assessment of possible inference between wave energy converters (WEC).

Antibacterial drugs in the form of sprays for the topical treatment of pyodermas and dermatoses complicated with a secondary infection

Directory of Open Access Journals (Sweden)

YE. V. Matushevskaya

2014-01-01

Full Text Available The article covers issues related to the application of topical antibacterial drugs for the treatment of pyodermic skin diseases. The author describes mechanisms of action and advantages of the topical form of antibiotics and GCS for the topical treatment of pyodermas. The article substantiates indications for the administration of topical GCS drugs in a combination with antibacterial drugs. The efficacy and safety of antibacterial and combination topical drugs such as Neomycin, Oxycort and Polcortolon TC in the form sprays for the treatment of pyodermas and complicated forms of chronic dermatosis.

Advances in design and modeling of porous materials

Science.gov (United States)

Ayral, André; Calas-Etienne, Sylvie; Coasne, Benoit; Deratani, André; Evstratov, Alexis; Galarneau, Anne; Grande, Daniel; Hureau, Matthieu; Jobic, Hervé; Morlay, Catherine; Parmentier, Julien; Prelot, Bénédicte; Rossignol, Sylvie; Simon-Masseron, Angélique; Thibault-Starzyk, Frédéric

2015-07-01

This special issue of the European Physical Journal Special Topics is dedicated to selected papers from the symposium "High surface area porous and granular materials" organized in the frame of the conference "Matériaux 2014", held on November 24-28, 2014 in Montpellier, France. Porous materials and granular materials gather a wide variety of heterogeneous, isotropic or anisotropic media made of inorganic, organic or hybrid solid skeletons, with open or closed porosity, and pore sizes ranging from the centimeter scale to the sub-nanometer scale. Their technological and industrial applications cover numerous areas from building and civil engineering to microelectronics, including also metallurgy, chemistry, health, waste water and gas effluent treatment. Many emerging processes related to environmental protection and sustainable development also rely on this class of materials. Their functional properties are related to specific transfer mechanisms (matter, heat, radiation, electrical charge), to pore surface chemistry (exchange, adsorption, heterogeneous catalysis) and to retention inside confined volumes (storage, separation, exchange, controlled release). The development of innovative synthesis, shaping, characterization and modeling approaches enables the design of advanced materials with enhanced functional performance. The papers collected in this special issue offer a good overview of the state-of-the-art and science of these complex media. We would like to thank all the speakers and participants for their contribution to the success of the symposium. We also express our gratitude to the organization committee of "Matériaux 2014". We finally thank the reviewers and the staff of the European Physical Journal Special Topics who made the publication of this special issue possible.

Solar distiller of pyramidal covering and isolation in composite material the Plaster base and EPS; Destilador solar de cobertura piramidal e isolamento em material composito a base de Gesso e EPS

Energy Technology Data Exchange (ETDEWEB)

Santos, R. D.; Ribeiro, F. A.; Mendes, J. U.; Lima, R. S.; Souza, L. G.; Abreu, R. F.

2008-07-01

To demonstrate then term viability calorific and economic of the material, compared to the others conventional distiller, here is presented a solar distiller os simple stage, with has as main differential characteristics the geometry of the covering and the material used to make its coating. the model built has an area of 0,25 m{sup 2} and pyramidal covering, witch allows the collection of the distillate water in the four faces, different of just two like is found in the conventional distiller, besides promote the absorption of the radiation because of its versatility about the positioning of the sun. Not despite, its built is favored for the low cost associated and the agility in the process because it is made with a mix of gypsum, EPS ground and water, witch also attributes to the distiller thermal properties more favorable to the process of distillation. (Author)

Physical protection of nuclear materials: Experience in regulation, implementation and operations. Proceedings of a conference

International Nuclear Information System (INIS)

1998-01-01

The conference was held at IAEA Headquarters in Vienna from 10 to 14 November 1997. It was attended by 162 registered participants from 42 countries and eight international organizations. The 58 papers presented dealt with the experience of regulators, designers and facility operators, including response forces, in meeting the demands and requirements in this changing area of physical protection of nuclear materials and facilities. Individual abstracts were prepared for each of the papers. Topics covered include contemporary and emerging issues, experience in regulation, implementation at facilities, program assessment and cooperation, hardware and software, illicit trafficking in nuclear materials, and transportation

PREFACE: MRS International Materials Research Conference (IMRC-2008)

Science.gov (United States)

Wang, Zhanguo; Qiu, Yong; Li, Yongxiang

2009-03-01

This volume contains selected papers presented at the MRS International Materials Research Conference (IMRC-2008) held in Chongqing, China, 9-12 June 2008. IMRC-2008 included 9 symposia of A. Eco/Environmental Materials, B. Sustainable Energy Materials, C. Electronic Packaging Materials, D. Electronic Materials, E. Materials and Processes for Flat-panel Displays, F. Functional Ceramics, G. Transportation Materials, H. Magnesium and I. Biomaterials for Medical Applications. Nearly 1200 participants from 33 countries attended the conference, and the conference organizers received more than 700 papers. After the peer review processes, 555 papers were selected to be published in 9 Journals or proceedings, including J. of Materials Research (JMR), Rare Metal Materials and Engineering, J. of Univ. Science and Technology Beijing, Biomedical Materials: Materials for Tissue Engineering and Regenerative Medicine, Chinese Journal of Aeronautics, Materials Science Forum, and Journal of Physics: Conference Series. Among the 555 selected papers, 91 papers are published in this volume, and the topics mainly cover electronic matrials, processes for flat-panel displays and functional ceramics. The editors would like to give special thanks to the graduate students Liwu Jiang, Ming Li and Di He from Beihang University for their hard work compiling and typesetting each paper in this volume. Zhanguo Wang, Yong Qiu and Yongxiang Li Editors

A Topic Analysis of ISECON Conference Proceedings from 1982 through 2014

Science.gov (United States)

Clark, Jon; Athey, Susan; Plotnicki, Jon; Barnes, Jay

2016-01-01

The authors note a distinct shift in topics covered in curricula as well as in conference presentations. This research was undertaken to get a better understanding of what these shifts have been, and determine their magnitude over time. Since ISECON has published its conference proceedings in digital format since 1982, this was a logical source of…

Covering a Crucible with Metal Containing Channels

Science.gov (United States)

Grugel, Richard N.

2006-01-01

In a procedure that partly resembles the lost-wax casting process, a crucible made of a brittle material (ceramic, quartz, or glass) is covered with a layer of metal containing channels. The metal cover and the channels can serve any or all of several purposes, depending upon the application: Typically, the metal would serve at least partly to reinforce the crucible. The channels could be used as passages for narrow objects that could include thermocouples and heat-transfer strips. Alternatively or in addition, channels could be used as flow paths for liquid or gaseous coolants and could be positioned and oriented for position- or direction-selective cooling. In some cases, the channels could be filled with known gases and sealed so that failure of the crucibles could be indicated by instruments that detect the gases. The process consists of three main steps. In the first step, a pattern defining the channels is formed by wrapping or depositing a material in the desired channel pattern on the outer surface of the crucible. The pattern material can be a plastic, wax, low-ash fibrous material, a soluble material, or other suitable material that can subsequently be removed easily. In a proof-of-concept demonstration (see figure), the crucible was an alumina cylinder and the mold material was plastic tie-down tape. In the second step, the patterned crucible is coated with metal. In one variation of the second step, a very thin layer containing or consisting of an electrically conductive material (e.g., gold, silver, or carbon) is painted or otherwise deposited on the mold-covered crucible, then the covering metal required for the specific application is electrodeposited on the very thin conducting layer. In another variation of the second step, the metal coat is formed by chemical vapor deposition. In the proof-of-concept demonstration, a layer of nickel 0.003 in. ( 0.08 mm) thick was electrodeposited. In the third step, the patterned material is removed. This is

A treaty on the cutoff of fissile material for nuclear weapons - What to cover? How to verify?

International Nuclear Information System (INIS)

Schaper, A.

1998-01-01

Since 1946, a cutoff has been proposed. In 1993, the topic was placed on the agenda of the CD. The establishment of an Ad Hoc Committee in the CD with a mandate to negotiate a fissile material cutoff treaty struggled with difficulties for more than a year. The central dispute was whether the mandate should refer to existing un-safeguarded stockpiles. The underlying conflict of the CTBT negotiations can be summarized as nuclear disarmament versus nuclear nonproliferation The same conflict is now blocking progress with FMCT negotiations in the CD. At the center of technical proliferation concerns is direct use material that can be used for nuclear warheads without any further enrichment or reprocessing. Those materials are plutonium and highly enriched uranium (HEU). A broader category of materials is defined as all those containing any fissile isotopes, called special fissionable materials. In order ta verify that no direct use materials are abused for military purposes, also special fissionable materials must be controlled. An even broader category is simply called nuclear materials. Pu and HEU can be distinguished into the following categories of utilisation: 1. military direct use material in operational nuclear weapons and their logistics pipeline, 2. military direct use material held in reserve for military purposes, in assembled weapons or in other forms, 3. military direct use material withdrawn from dismantled weapons, 4. military direct use material considered excess and designated for transfer into civilian use, 5. military direct use material considered excess and declared for transfer into civilian use, 6. direct use material currently in reactors or their logistics pipelines and storages, and 7. irradiated Pu and HEU in spent fuel from reactors, or in vitrified form for final disposal. Large quantities of materials are neither inside weapons nor declared excess. So far, there are no legal obligations for NWS for limitations, declarations, or

AMNT 2014. Key Topic: Reactor operation, safety - report. Pt. 1

Energy Technology Data Exchange (ETDEWEB)

Schaffrath, Andreas [Gesellschaft fuer Anlagen- und Reaktorsicherheit mbH (GRS), Garching (Germany). Forschungszentrum

2014-10-15

Summary report on one session of the Annual Conference on Nuclear Technology held in Frankfurt, 6 to 8 May 2014: - Safety of Nuclear Installations - Methods, Analysis, Results: Backfittings for the Improvement of Safety and Efficiency. The other Sessions of the Key Topics 'Reactor Operation, Safety', 'Competence, Innovation, Regulation' and 'Fuel, Decommissioning and Disposal' will be covered in further issues of atw.

PREFACE: Advanced Materials for Demanding Applications

Science.gov (United States)

McMillan, Alison; Schofield, Stephen; Kelly, Michael

2015-02-01

This was a special conference. It was small enough (60+ delegates) but covering a wide range of topics, under a broad end-use focussed heading. Most conferences today either have hundreds or thousands of delegates or are small and very focussed. The topics ranged over composite materials, the testing of durability aspects of materials, and an eclectic set of papers on radar screening using weak ionized plasmas, composites for microvascular applications, composites in space rockets, and materials for spallation neutron sources etc. There were several papers of new characterisation techniques and, very importantly, several papers that started with the end-user requirements leading back into materials selection. In my own area, there were three talks about the technology for the ultra-precise positioning of individual atoms, donors, and complete monolayers to take modern electronics and optoelectronics ideas closer to the market place. The President of the Institute opened with an experience-based talk on translating innovative technology into business. Everyone gave a generous introduction to bring all-comers up to speed with the burning contemporary issues. Indeed, I wish that a larger cohort of first-year engineering PhD students were present to see the full gamut of what takes a physics idea to a success in the market place. I would urge groups to learn from Prof Alison McMillan (a Vice President of the Institute of Physics) and Steven Schofield, to set up conferences of similar scale and breadth. I took in more than I do from mega-meetings, and in greater depth. Professor Michael Kelly Department of Engineering University of Cambridge

Synthesis, properties and applications of 2D non-graphene materials

International Nuclear Information System (INIS)

Wang, Feng; Wang, Zhenxing; Wang, Qisheng; Wang, Fengmei; Yin, Lei; Xu, Kai; Huang, Yun; He, Jun

2015-01-01

As an emerging class of new materials, two-dimensional (2D) non-graphene materials, including layered and non-layered, and their heterostructures are currently attracting increasing interest due to their promising applications in electronics, optoelectronics and clean energy. In contrast to traditional semiconductors, such as Si, Ge and III–V group materials, 2D materials show significant merits of ultrathin thickness, very high surface-to-volume ratio, and high compatibility with flexible devices. Owing to these unique properties, while scaling down to ultrathin thickness, devices based on these materials as well as artificially synthetic heterostructures exhibit novel and surprising functions and performances. In this review, we aim to provide a summary on the state-of-the-art research activities on 2D non-graphene materials. The scope of the review will cover the preparation of layered and non-layered 2D materials, construction of 2D vertical van der Waals and lateral ultrathin heterostructures, and especially focus on the applications in electronics, optoelectronics and clean energy. Moreover, the review is concluded with some perspectives on the future developments in this field. (topical review)

Proceedings of the international conference on material science: abstract volume

International Nuclear Information System (INIS)

2013-01-01

Materials Science is an interdisciplinary field applying the properties of matter to various areas of science and engineering. This scientific field investigates the relationship between the structure of materials at atomic or molecular scales and their macroscopic properties. In the recent years, materials science has been propelled to the forefront at many universities and research institutions due to the significant advancement on nanoscience and nanotechnology. ICMS-2013 will cover a wide range of interdisciplinary and current research topics related to material science. Research on advanced materials includes nanomaterials, bio-nanomaterials, zero bandgap materials, composites, surface engineering, tissue engineering and biomaterials etc. These materials have numerous applications in electronics, biotechnology, medicine and energy harvesting. The importance of nano-science and nanotechnology has been well documented by both industrial and academic communities worldwide. It is believed that breakthroughs in nano-science and technology will change all aspects of human life in such diverse areas as, electronic devices, energy, biomedicine, sensing, environment, and security etc. Papers relevant to INIS are indexed separately

Postcards from the past: Archaeological and industrial analogs for deep repository materials

International Nuclear Information System (INIS)

Miller, B.; Chapman, N.

1995-01-01

Many recent performance assessments of deep geological repositories for radioactive wastes suggest that the engineered barrier system plays the cominant role in reducing releases of radionuclides to the surface environment. There is a considerable impetus to demonstrate the longevity of engineered barrier system components. Although many of the materials are familiar, the requirement for predictable behavior and longevity in a repository is unlike any other requirements of the past. A full appreciation of the acceptability of repository materials can only be reached from a combination of complementary field, laboratory, and natural analog studies. This article discusses analogs from archaelogy and industry. Topics covered include what makes a good analog; long term material behavior (from archeological studies) of metals, glass,cements and concrete, bitumens, and betonite; investigations of radionuclide transport and material interactions. 4 figs., 3 tabs

Escalation of terrorism? On the risk of attacks with chemical, biological, radiological and nuclear weapons or materials; Eskalation des Terrors? Ueber das Anschlagsrisiko mit chemischen, biologischen, radiologischen und nuklearen Waffen oder Stoffen

Energy Technology Data Exchange (ETDEWEB)

Nass, Jens

2010-07-01

The report on the risk of attacks with chemical, biological, radiological and nuclear weapons or materials covers the following topics: the variety of terrorism: ethnic-nationalistic, politically motivated, social revolutionary, political extremism, religious fanaticism, governmental terrorism; CBRN (chemical, biological, radiological, nuclear) weapons and materials: their availability and effectiveness in case of use; potential actor groups; prevention and counter measures, emergency and mitigating measures.

Strategies for discovery and optimization of thermoelectric materials: Role of real objects and local fields

Science.gov (United States)

Zhu, Hao; Xiao, Chong

2018-06-01

Thermoelectric materials provide a renewable and eco-friendly solution to mitigate energy shortages and to reduce environmental pollution via direct heat-to-electricity conversion. Discovery of the novel thermoelectric materials and optimization of the state-of-the-art material systems lie at the core of the thermoelectric society, the basic concept behind these being comprehension and manipulation of the physical principles and transport properties regarding thermoelectric materials. In this mini-review, certain examples for designing high-performance bulk thermoelectric materials are presented from the perspectives of both real objects and local fields. The highlights of this topic involve the Rashba effect, Peierls distortion, local magnetic field, and local stress field, which cover several aspects in the field of thermoelectric research. We conclude with an overview of future developments in thermoelectricity.

Material efficiency: providing material services with less material production.

Science.gov (United States)

Allwood, Julian M; Ashby, Michael F; Gutowski, Timothy G; Worrell, Ernst

2013-03-13

Material efficiency, as discussed in this Meeting Issue, entails the pursuit of the technical strategies, business models, consumer preferences and policy instruments that would lead to a substantial reduction in the production of high-volume energy-intensive materials required to deliver human well-being. This paper, which introduces a Discussion Meeting Issue on the topic of material efficiency, aims to give an overview of current thinking on the topic, spanning environmental, engineering, economics, sociology and policy issues. The motivations for material efficiency include reducing energy demand, reducing the emissions and other environmental impacts of industry, and increasing national resource security. There are many technical strategies that might bring it about, and these could mainly be implemented today if preferred by customers or producers. However, current economic structures favour the substitution of material for labour, and consumer preferences for material consumption appear to continue even beyond the point at which increased consumption provides any increase in well-being. Therefore, policy will be required to stimulate material efficiency. A theoretically ideal policy measure, such as a carbon price, would internalize the externality of emissions associated with material production, and thus motivate change directly. However, implementation of such a measure has proved elusive, and instead the adjustment of existing government purchasing policies or existing regulations-- for instance to do with building design, planning or vehicle standards--is likely to have a more immediate effect.

Materials reliability in the back end of the nuclear fuel cycle

International Nuclear Information System (INIS)

1987-05-01

Operating experience of nuclear fuel cycle facilities has proved that the performance and availability of key equipment largely depend on the reliability of its construction materials. In general, the materials of construction have performed well in accordance with the design criteria of equipment. In some cases, however, materials failure problems have been encountered, the causes of which are related to their corrosion and mechanical degradation. In response to the growing interest in these topics, the IAEA convened the Technical Committee Meeting on ''Materials Reliability in the Back-End of the Nuclear Fuel Cycle'' at its Headquarters from September 2 to 5, 1986. This Technical Document contains the 15 papers presented during the Meeting. Material aspects of the following fields of the back-end of the nuclear fuel cycle are covered: interim and long-term storage of spent fuel; final disposal of spent fuel; storage and vitrification of High Level Liquid Wastes (HLLW); long-term storage of High Level Wastes (HLW); and spent fuel treatment

In-vitro interactions of human chondrocytes and mesenchymal stem cells, and of mouse macrophages with phospholipid-covered metallic implant materials

Directory of Open Access Journals (Sweden)

R Willumeit

2007-03-01

Full Text Available Phospholipid-coatings on metallic implant surfaces were evaluated in terms of adhesion, proliferation and matrix production of skeletal cells, and of macrophage stimulation. The working hypothesis is that mimicking a model biomembrane by phospholipids on surfaces to which cells adhere, the surface recognition by surrounding cells is altered. In this study, 1 mirror-like polished Ti-6Al-7Nb and 2 porous Ti-6Al-4V specimens were covered with the phospholipids POPE (palmitoyl-oleoyl phosphatidyl-ethanolamine and POPC (palmitoyl-oleoyl phosphatidyl-choline, and the interactions of a human articular chondrocytes (HAC, b human mesenchymal stem cells (HMSC, and c mouse macrophages (RAW 264.7 were tested in vitro. On POPE-covered polished surfaces adherence of HAC (42% of seeded cells after 2 hrs and metabolic activity (MTT after 3 days were reduced, while on porous surfaces 99% HAC adhered, and metabolic activity was significantly increased, compared to respective native surfaces. On both POPE-covered surfaces the chondrocyte phenotype was present. After 3 weeks of chondrogenic differentiation, cartilage matrix production (measuring chondroitin sulphate per HAC number was significantly increased by about 30% on both POPE-covered metallic surfaces. On both POPC-covered surfaces nearly no adhering and surviving HAC were found. HMSC grown on POPE-covered porous substrates showed osteogenic differentiation by improved osteopontin and collagen I expression in RT-PCR, and osteocalcin fluorescence and bone nodule formation was only detectable on POPE-covered porous surfaces. In contrast to POPC and other phospholipids used as positive controls, POPE did not stimulate the NO production in mouse macrophage cultures. We therefore conclude that a phospholipid coating by POPE shows potential as surface modification for metallic implant materials.

Investigation of test methods, material properties, and processes for solar cell encapsulants. Annual report

Energy Technology Data Exchange (ETDEWEB)

Willis, P. B.; Baum, B.; Schnitzer, H. S.

1980-07-01

The goal of this program is to identify, evaluate, and recommend encapsulant materials and processes for the production of cost-effective, long-life solar cell modules. Technical activities during the past year have covered a number of topics and have emphasized the development of solar module encapsulation technology that employs ethylene/vinyl acetate, copolymer (EVA) as the pottant. These activities have included: (1) continued production of encapsulation grade EVA in sheet form to meet the needs of the photovoltaic industry; (2) investigations of three non-blocking techniques for EVA sheet; (3) performed an economic analysis of the high volume production of each pottant in order to estimate the large volume selling price (EVA, EPDM, aliphatic urethane, PVC plastisol, and butyl acrylate); (4) initiated an experimental corrosion protection program to determine if metal components could be successfully protected by encapsulation; (5) began an investigation to determine the maximum temperature which can be tolerated by the candidate pottant material in the event of hot spot heating or other temperature override; (6) continuation of surveys of potentially useful outer cover materials; and (7) continued with the accelerated artificial weathering of candidate encapsulation materials. Study results are presented. (WHK)

Research of radioactive waste storage cask/canister materials, spent nuclear fuels and various radioactive waste forms and development of their assessment methods. Final report for Stage 3

International Nuclear Information System (INIS)

Dobrev, D.; Balek, V.; Červinka, R.; Večerník, P.; Člupek, M.; Kouřil, M.; Novák, P.; Stoulil, J.; Silber, R.

2013-08-01

The main topics treated are: Research and development of methodologies for canister/cask material degradation assessment; Laboratory research of selected materials of canister/cask with radioactive waste; and Research and assessment of canister/cask materials in natural granite rocks. Two additional documents are appended: Corrosion rate determination for samples in compacted bentonite in anaerobic conditions (methodology), and Roll test for corrosion test in an occluded solution at the interface between a radioactive waste disposal canister and the bentonite cover. (P.A.)

Topics in field theory

CERN Document Server

Karpilovsky, G

1989-01-01

This monograph gives a systematic account of certain important topics pertaining to field theory, including the central ideas, basic results and fundamental methods.Avoiding excessive technical detail, the book is intended for the student who has completed the equivalent of a standard first-year graduate algebra course. Thus it is assumed that the reader is familiar with basic ring-theoretic and group-theoretic concepts. A chapter on algebraic preliminaries is included, as well as a fairly large bibliography of works which are either directly relevant to the text or offer supplementary material of interest.

Control of electro-chemical processes using energy harvesting materials and devices.

Science.gov (United States)

Zhang, Yan; Xie, Mengying; Adamaki, Vana; Khanbareh, Hamideh; Bowen, Chris R

2017-12-11

Energy harvesting is a topic of intense interest that aims to convert ambient forms of energy such as mechanical motion, light and heat, which are otherwise wasted, into useful energy. In many cases the energy harvester or nanogenerator converts motion, heat or light into electrical energy, which is subsequently rectified and stored within capacitors for applications such as wireless and self-powered sensors or low-power electronics. This review covers the new and emerging area that aims to directly couple energy harvesting materials and devices with electro-chemical systems. The harvesting approaches to be covered include pyroelectric, piezoelectric, triboelectric, flexoelectric, thermoelectric and photovoltaic effects. These are used to influence a variety of electro-chemical systems such as applications related to water splitting, catalysis, corrosion protection, degradation of pollutants, disinfection of bacteria and material synthesis. Comparisons are made between the range harvesting approaches and the modes of operation are described. Future directions for the development of electro-chemical harvesting systems are highlighted and the potential for new applications and hybrid approaches are discussed.

Topical tags vs non-topical tags : Towards a bipartite classification?

NARCIS (Netherlands)

Basile, Valerio; Peroni, Silvio; Tamburini, Fabio; Vitali, Fabio

2015-01-01

In this paper we investigate whether it is possible to create a computational approach that allows us to distinguish topical tags (i.e. talking about the topic of a resource) and non-topical tags (i.e. describing aspects of a resource that are not related to its topic) in folksonomies, in a way that

TOPICAL REVIEW: First principles studies of multiferroic materials

Science.gov (United States)

Picozzi, Silvia; Ederer, Claude

2009-07-01

Multiferroics, materials where spontaneous long-range magnetic and dipolar orders coexist, represent an attractive class of compounds, which combine rich and fascinating fundamental physics with a technologically appealing potential for applications in the general area of spintronics. Ab initio calculations have significantly contributed to recent progress in this area, by elucidating different mechanisms for multiferroicity and providing essential information on various compounds where these effects are manifestly at play. In particular, here we present examples of density-functional theory investigations for two main classes of materials: (a) multiferroics where ferroelectricity is driven by hybridization or purely structural effects, with BiFeO3 as the prototype material, and (b) multiferroics where ferroelectricity is driven by correlation effects and is strongly linked to electronic degrees of freedom such as spin-, charge-, or orbital-ordering, with rare-earth manganites as prototypes. As for the first class of multiferroics, first principles calculations are shown to provide an accurate qualitative and quantitative description of the physics in BiFeO3, ranging from the prediction of large ferroelectric polarization and weak ferromagnetism, over the effect of epitaxial strain, to the identification of possible scenarios for coupling between ferroelectric and magnetic order. For the second class of multiferroics, ab initio calculations have shown that, in those cases where spin-ordering breaks inversion symmetry (e.g. in antiferromagnetic E-type HoMnO3), the magnetically induced ferroelectric polarization can be as large as a few µC cm-2. The examples presented point the way to several possible avenues for future research: on the technological side, first principles simulations can contribute to a rational materials design, aimed at identifying spintronic materials that exhibit ferromagnetism and ferroelectricity at or above room temperature. On the

Safe transport of radioactive material

International Nuclear Information System (INIS)

1990-01-01

Recently the Agency redefined its policy for education and training in radiation safety. The emphasis is now on long-term strategic planning of general education and training programmes. In line with this general policy the Agency's Standing Advisory Group for the Safe Transport of Radioactive Material (SAGSTRAM) in its 7th meeting (April 1989) agreed that increased training activity should be deployed in the area of transport. SAGSTRAM specifically recommended the development of a standard training programme on this subject area, including audio-visual aids, in order to assist Member States in the implementation of the Agency's Regulations for the Safe Transport of Radioactive Material. This training programme should be substantiated by a biennial training course which is thought to be held either as an Interregional or a Regional Course depending on demand. This training manual, issued as a first publication in the Training Course Series, represents the basic text material for future training courses in transport safety. The topic areas covered by this training manual and most of the texts have been developed from the course material used for the 1987 Bristol Interregional Course on Transport Safety. The training manual is intended to give guidance to the lecturers of a course and will be provided to the participants for retention. Refs, figs and tabs

Covering of milled peat stockpile with wood chips; Jyrsinturveauman peittaeminen hakkeella

Energy Technology Data Exchange (ETDEWEB)

Franssila, T.; Leinonen, A.

1996-12-31

The aim of this project is to research the applicability of wooden materials for protection of milled peat stockpile against losses during storaging. Water transmission features of sawdust, wastewood chip and whole tree chip were investigated in laboratory with raining experiments. The plan for raining experiments was made with experiment planning program and results were analysed with multivariate analysis. Freezing features were investigated thorough breaking tests with hydraulic piston vice. Laboratory experiments were completed with field tests in Laakasuo near Sotkamo. On the basis of results covering peat stockpiles with sawdust is fully competitive comparing to present covering methods. Chip materials are technically not as good covering materials as sawdust

Meeting of the ITPA Topical Group on Diagnostics

International Nuclear Information System (INIS)

Costley, A.E.; Donne, A.J.H.

2002-01-01

The first meeting of the International Tokamak Physics Activities (ITPA) Topical Group (TG) on diagnostics was held at the Ioffe Physical-Technical institute, St. Petersburg, Russian Federation, on 14-16 November 2001. In total 38 participants attended the meeting and all four ITPA partners (EU, JA, RF and US) were represented. This summary covers mainly the discussions at the TG meeting. The meeting immediately followed a progress meeting, held in the same location on 12-13 November 2001, on the efforts carried out in the Russian Federation on diagnostics for ITER and burning plasma experiments

THz TDS of substance covered by disordered structure

Science.gov (United States)

Trofimov, V. A.; Zagursky, D. Y.; Zakharova, I. G.

2016-04-01

Computer simulation of a few-cycle pulse interaction with a substance covered by disordered structure is performed in order to study the effects imposed on spectra of transmitted and reflected pulses by presence of the cover. The substance is described by semi-classic approach and the cover is described by classic electrodynamics equations for linear isotropic medium. The cover consists of a number of layers with different properties which is considered to be the cause of the distortions. The influence of relation between pulse wavelength and cover layer thickness is illustrated. Computer simulation results are compared with those of physical experiments conducted for paper and other common materials.

Topical Ranibizumab as a Treatment of Corneal Neovascularization

Science.gov (United States)

Ferrari, Giulio; Dastjerdi, Mohammad H.; Okanobo, Andre; Cheng, Sheng-Fu; Amparo, Francisco; Nallasamy, Nambi; Dana, Reza

2014-01-01

Purpose To examine the effect of topical ranibizumab on clinically stable corneal neovascularization (NV). Methods This was a prospective, open-label, monocentric, uncontrolled, non-comparative study. Ten eyes of 9 patients with corneal NV received topical ranibizumab (1%) 4 times a day for 3 weeks with a follow-up of 16 weeks. The main corneal neovascularization outcome measures were: neovascular area (NA), the area occupied by the corneal neovessels; vessel caliber (VC), the mean diameter of the corneal neovessels; and invasion area (IA), the fraction of the total cornea area covered by the vessels. This study was conducted at the Massachusetts Eye and Ear Infirmary, Boston, MA, USA. Results Statistically significant decreases in NA (55.3%, P<0.001), which lasted through 16 weeks, and VC (59%, P<0.001), which continued to improve up to week 16, were observed after treatment. No significant decrease was observed in IA (12.3%, P=0.49). There was no statistically significant change in visual acuity or intraocular pressure. No adverse events ascribed to the treatment were noted. Conclusions Topical application of ranibizumab is effective in reducing the severity of corneal NV in the context of established corneal NV, mostly through decrease in VC rather than IA. PMID:23407316

OpenMPI and ExxonMobil Topics

Energy Technology Data Exchange (ETDEWEB)

Hjelm, Nathan Thomas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Pritchard, Howard Porter [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-09-09

These are a series of slides for a presentation for ExxonMobil's visit to Los Alamos National Laboratory. Topics covered are: Open MPI - The Release Story, MPI-3 RMA in Open MPI, MPI dynamic process management and Open MPI, and new options with CLE 6. Open MPI RMA features are: since v2.0.0 full support for the MPI-3.1 specification, support for non-contiguous datatypes, support for direct use of the RDMA capabilities of high performance networks (Cray Gemini/Aries, Infiniband), starting in v2.1.0 will have support for using network atomic operations for MPI_Fetch_and_op and MPI_Compare_and_swap, tested with MPI_THREAD_MULTIPLE.

Two-Dimensional Spectroscopy Is Being Used to Address Core Scientific Questions in Biology and Materials Science.

Science.gov (United States)

Petti, Megan K; Lomont, Justin P; Maj, Michał; Zanni, Martin T

2018-02-15

Two-dimensional spectroscopy is a powerful tool for extracting structural and dynamic information from a wide range of chemical systems. We provide a brief overview of the ways in which two-dimensional visible and infrared spectroscopies are being applied to elucidate fundamental details of important processes in biological and materials science. The topics covered include amyloid proteins, photosynthetic complexes, ion channels, photovoltaics, batteries, as well as a variety of promising new methods in two-dimensional spectroscopy.

Recent Topical Research on Global, Energy, Health & Medical, and Tourism Economics, and Global Software

NARCIS (Netherlands)

C-L. Chang (Chia-Lin); M.J. McAleer (Michael)

2017-01-01

textabstractThe paper presents an overview of recent topical research on global, energy, health & medical, and tourism economics, and global software. We have interpreted “global” in the title of the Journal of Reviews on Global Economics to cover contributions that have a global impact on

SU-F-T-379: Dosimetric Impacts of Topical Agents and Dressings On Skin in Radiotherapy

Energy Technology Data Exchange (ETDEWEB)

Tse, K; Morley, L; Cashell, A; Sperduti, A; McQuestion, M; Chow, J [Princess Margaret Cancer Centre, Toronto, ON (Canada)

2016-06-15

Purpose: This study investigated the superficial dose enhancement in the application of topical agents, clinical materials (thermal mask and bolus) and dressings in megavoltage photon beam radiotherapy. Different topical skin agents, clinical materials and dressings were evaluated and compared for their skin dosimetric impacts on the patients during radiation treatment. Methods: Superficial dose enhancements, or percentage doses with and without the studying materials, were measured using the 6 MV (Field size = 10×10 cm{sup 2}) photon beams produced by a Varian TrueBeam linear accelerator. Twelve topical agents, five dressings (dry and wet conditions) and three clinical materials were studied. A solid water phantom was used with a MOSFET dose detector (TN-1002RD, Thomson and Nielsen Electronic, Ottawa, Ontario, Canada) located under a 1-mm PMMA slab to measure the skin dose. The distance between the radiation source and phantom surface was set to 100 cm in all measurements. The topical agents were distributed evenly with 1.5 mm thickness using our specific sample holder on the phantom surface. Extrapolations were made of 0.5 mm thickness for the agents to provide meaningful clinical value. Results: By comparing surface doses without studying materials, it is found that no topical agents had superficial dose enhancement higher than the clinical materials namely, thermoplastic mask (128%), 5-mm Superflab™ bolus (158%) and 10-mm Superflab™ bolus (171%) regarding the same thickness. Superficial dose enhancement of dry dressing did not exceed 110.5%, while wet dressings produced higher dose enhancements (133% for wet Mepilex lite and 141% for wet Mepilex Ag transfer). Conclusion: It is concluded that the evaluated topical agents and dry dressings did not increase the superficial dose to a concerning level, even using excessive thickness in every fraction of radiation treatment. Wet dressings were found producing the bolus effect, but was still substantially less

SU-F-T-379: Dosimetric Impacts of Topical Agents and Dressings On Skin in Radiotherapy

International Nuclear Information System (INIS)

Tse, K; Morley, L; Cashell, A; Sperduti, A; McQuestion, M; Chow, J

2016-01-01

Purpose: This study investigated the superficial dose enhancement in the application of topical agents, clinical materials (thermal mask and bolus) and dressings in megavoltage photon beam radiotherapy. Different topical skin agents, clinical materials and dressings were evaluated and compared for their skin dosimetric impacts on the patients during radiation treatment. Methods: Superficial dose enhancements, or percentage doses with and without the studying materials, were measured using the 6 MV (Field size = 10×10 cm"2) photon beams produced by a Varian TrueBeam linear accelerator. Twelve topical agents, five dressings (dry and wet conditions) and three clinical materials were studied. A solid water phantom was used with a MOSFET dose detector (TN-1002RD, Thomson and Nielsen Electronic, Ottawa, Ontario, Canada) located under a 1-mm PMMA slab to measure the skin dose. The distance between the radiation source and phantom surface was set to 100 cm in all measurements. The topical agents were distributed evenly with 1.5 mm thickness using our specific sample holder on the phantom surface. Extrapolations were made of 0.5 mm thickness for the agents to provide meaningful clinical value. Results: By comparing surface doses without studying materials, it is found that no topical agents had superficial dose enhancement higher than the clinical materials namely, thermoplastic mask (128%), 5-mm Superflab™ bolus (158%) and 10-mm Superflab™ bolus (171%) regarding the same thickness. Superficial dose enhancement of dry dressing did not exceed 110.5%, while wet dressings produced higher dose enhancements (133% for wet Mepilex lite and 141% for wet Mepilex Ag transfer). Conclusion: It is concluded that the evaluated topical agents and dry dressings did not increase the superficial dose to a concerning level, even using excessive thickness in every fraction of radiation treatment. Wet dressings were found producing the bolus effect, but was still substantially less than

Preface to Special Topic: Acoustic Metamaterials and Metasurfaces

Science.gov (United States)

Assouar, Badreddine

2018-03-01

The advent of acoustic metamaterials in the beginning of 2000s and very recently of acoustic metasurfaces has created tremendous excitement and efforts in the field of materials science and physics by introducing and building real transformative research and dealing with unprecedented physics and applications. The acoustic/elastic metamaterials and metasurfaces, which can simply be described as designed artificial materials with unusual physical properties, form the core of the present Special Topic published by the Journal of Applied Physics.

Factors influencing radon attenuation by tailing covers

International Nuclear Information System (INIS)

Silker, W.B.; Rogers, V.C.

1981-07-01

The US NRC, in its Generic Environmental Impact Statement on uranium milling has specified that the radon flux escaping a uranium mill tailings pile will be reduced to pCi/m 2 s by application of covering layers of soils and clays. These covers present a radon diffusion barrier, which sufficiently increases the time required for radon passage from the tailings to the atmosphere to allow for decay of 222 Rn within the cover. The depth of cover necessary to reduce the escaping radon flux to the prescribed level is to be determined by calculation, and requires precise knowledge of the radon diffusion coefficient in the covering media. A Radon Attenuation Test Facility was developed to determine rates of radon diffusion through candidate cover materials. This paper describes this facility and its application for determining the influence of physical properties of the soil column on the radon diffusion coefficient

Topical diclofenac therapy for osteoarthritis: a meta-analysis of randomized controlled trials.

Science.gov (United States)

Deng, Zhen-Han; Zeng, Chao; Yang, Ye; Li, Yu-Sheng; Wei, Jie; Yang, Tuo; Li, Hui; Lei, Guang-Hua

2016-05-01

The objective of this study was to evaluate the efficacy and safety of topical diclofenac therapy for osteoarthritis (OA). A meta-analysis of randomized controlled trials was conducted. A comprehensive literature search, covering the databases of Medline, the Cochrane Central Register of Controlled Trials, and EMBASE, was conducted in September 2014 to identify the randomized controlled trials which adopted the topical diclofenac therapy for OA. A total of nine papers were included in this meta-analysis. Topical diclofenac appears to be effective in both pain relief (standard mean differences (SMD) = 0.40; 95 % confidence interval (CI) 0.19 to 0.62; P = 0.0003) and function improvement (SMD = 0.23; 95 % CI 0.03 to 0.43; P = 0.03) when compared with the control group. The sensitivity analysis and subgroup analysis showed that the result of pain intensity was stable and reliable, while the result of physical function improvement was vague. With respect to safety, topical diclofenac demonstrated a higher incidence of adverse events such as dry skin, rash, dermatitis, neck pain, and withdrawal. Topical diclofenac is effective in pain relief as a treatment of OA. It may also have a potential effect in function improvement, which needs further studies to be explored. Although, some adverse effects were observed in the application of topical diclofenac, none of them was serious.

Oxygen diffusion through soil covers on sulphidic mine tailings

International Nuclear Information System (INIS)

Yanful, E.K.

1993-01-01

Engineered soil covers are being evaluated under Canada's Mine Environment Neutral Drainage (MEND) program for their effectiveness in preventing and controlling acid generation in sulfidic mill tailings. A critical parameter for predicting the performance of these covers is the diffusion coefficient of gaseous oxygen in the cover materials. Laboratory experiments conducted to determine the effective diffusion coefficient of a candidate cover material, a glacial till from an active mine site, are described. The diffusion coefficient is determined by fitting a semianalytic solution of the one-dimensional, transient diffusion equation to experimental gaseous oxygen concentration versus time graphs. Effective diffusion coefficients determined at high water saturations (85%--95%) were of the order of 8 x 10 -8 m 2 /s. The diffusion coefficients decreased with increase in water saturation as a result of the low diffusivity of gaseous oxygen in water relative to that in air and the low solubility of oxygen in water. Placement of soil covers in high saturation conditions would ensure that the flux of oxygen into tailings underneath such covers is low, resulting in low acid flux. This is confirmed by combined laboratory, field, and modeling studies

Materials to be covered by accountancy and control

International Nuclear Information System (INIS)

Bellinger, J.

1989-01-01

In the State System of Accounting for and Control of Nuclear Materials it is the responsibility of the National Authority to prescribe the points at which nuclear material begins to attract full accounting and control, and when accounting and control are terminated. NPT-type safeguards agreements, as well as prescribing the starting and terminating ponts for international safeguards, permit exemption and de-exemption from safeguards. These matters are discussed with the Australian experience providing examples

Solid State and Materials Chemistry

Indian Academy of Sciences (India)

Unknown

experiment and theory. Moreover, the alumni of the ... international activity. The topics covered include: self-assembly of complex inorganic ... oxides, ab initio structure determination using powder X-ray diffraction, epitaxial oxide films, quantum ...

Engineered soil covers for management of salt impacted sites

International Nuclear Information System (INIS)

Sweeney, D.A.; Tratch, D.J.

2005-01-01

The use of engineered soil cover systems to mitigate environmental impacts from tailings and waste rock piles is becoming an accepted practice. This paper presented design concepts for soil covers related to reclamation practices in the mining industry as an effective risk management practice at salt impacted sites. Research and field programs have demonstrated that a layered engineered soil cover can reduce or eliminate infiltration. Key components of the system included re-establishing surface vegetation to balance precipitation fluxes with evapotranspiration potential, and design of a capillary break below the rooting zone to minimize deeper seated infiltration. It was anticipated that the incorporation of a vegetation cover and a capillary break would minimize infiltration into the waste rock or tailing pile and reduce the generation of acid rock drainage (ARD). Design of a layered soil cover requires the incorporation of meteorological data, moisture retention characteristics of the impacted soils, and proposed engineered cover materials. Performance of the soil cover was predicted using a finite element model combined with meteorological data from the site area, unsaturated soil properties of the parent sub-surface soils and potential covered materials. The soil cover design consisted of re-vegetation and a loose clay cover overlying a compacted till layer. The design was conducted for an off site release of salt impacted pasture land adjacent to a former highway maintenance yard. The model predicted minimal infiltration during high precipitation events and no infiltration during low precipitation events. Results indicated that the proposed soil cover would enable re-establishment of a productive agricultural ground cover, as well as minimizing the potential for additional salt migration. It was concluded that further research and development is needed to ensure that the cover system is an acceptable method for long-term risk management. 17 refs., 5 figs

Changing the Topic. Topic Position in Ancient Greek Word Order

NARCIS (Netherlands)

Allan, R.J.

2014-01-01

Ancient Greek, topics can be expressed as intra-clausal constituents but they can also precede or follow the main clause as extra-clausal constituents. Together, these various topic expressions constitute a coherent system of complementary pragmatic functions. For a comprehensive account of topic

Summary of the materials breakout group

Energy Technology Data Exchange (ETDEWEB)

Garner, F. [Pacific Northwest Laboratories, Richland, WA (United States); Sommer, W. [Los Alamos National Laboratory, NM (United States)

1995-10-01

This breakout group discussed the following topics and reached a number of recommendations summarized in this report. The topics of discussion included (1) a comparison of expected materials response at spallation sources to experience with fission reactors; (2) synergistic effects from high-energy particle radiation, corrosion, and cyclic stresses; (3) estimates, based on experience with materials developed for fission and fusion reactors, for -materials testing needs; - facilities for materials development, both available and needed; - candidate materials; - time frame for material qualification; and - expected program costs.

Topical Hazard Evaluation Program of Candidate Insect Repellent AI3- 39053a

Science.gov (United States)

1987-05-01

StudyNo. 75-51-O 71-R7 Mnay 19R71 12 PERSONAL AUTHOR(S) William T. Huebsam, SGT, U.S.A.; Maurice H. Weeks 1I8. TYPE Of REPORT 13b TIME COVERED 114...ARMY u.S. AUT ENVIVIf[NNIAL HYGINE AMIdT ASCROELN PROVING GROUND. MARYLAND M1蚉 HSHB-MO-T TOPICAL HAZARD EVALUATION PROGRAM OF CANDIDATE INSECT

A Legal Odyssey, 2001. Papers [of the] Education Law Association Conference (47th, Albuquerque, New Mexico, November 15-17, 2001). Topic Outlines.

Science.gov (United States)

Education Law Association, Dayton, OH.

This document is a collection of 53 topic outlines and conference papers whose topics cover a multitude of aspects of educational law. Subjects include the impacts of the Individuals with Disabilities Education Act (IDEA) on "normal" students, rights of nontenured teachers, sexual discrimination and harassment, school disciplinary issues,…

Worldwide Utilization of Topical Remedies in Treatment of Psoriasis

DEFF Research Database (Denmark)

Svendsen, Mathias Tiedemann; Jeyabalan, Janithika; Andersen, Klaus Ejner

2017-01-01

OBJECTIVE: To review published literature describing the global use of topical antipsoriatics. MATERIAL AND METHODS: Search for English-language articles in Embase, Pubmed, PsycINFO, and Cochrane Library. RESULTS: Fifty-four selected publications were found, describing psoriasis patients' use of ...

46th Annual meeting on nuclear technology (AMNT 2015). Key topic / Enhanced safety and operation excellence / Sustainable reactor operation management - safe, efficient, valuable

International Nuclear Information System (INIS)

Fischer, Erwin

2015-01-01

Summary report on the following Topical Session of the 46 th Annual Conference on Nuclear Technology (AMNT 2015) held in Berlin, 5 to 7 May 2015: - Sustainable Reactor Operation Management - Safe, Efficient, Valuable (Erwin Fischer) The other Sessions of the Key Topics - ''Outstanding Know-How and Sustainable Innovations'', - ''Enhanced Safety and Operation Excellence'' and - ''Decommissioning Experience and Waste Management Solutions'' have been covered in atw 7 (2015) and will be covered in further issues of atw.

Atom probe field ion microscopy and related topics: A bibliography 1989

International Nuclear Information System (INIS)

Miller, M.K.; Hawkins, A.R.; Russell, K.F.

1990-12-01

This bibliography includes references related to the following topics: atom probe field ion microscopy (APFIM), field ion spectroscopy (FIM), field emission microscopy (FEM), liquid metal ion sources (LMIS), scanning tunneling microscopy (STM), and theory. Technique-orientated studies and applications are included. This bibliography covers the period 1989. The references contained in this document were compiled from a variety of sources including computer searches and personal lists of publications

SASP. Contributions to the 13. Symposium on atomic and surface physics and related topics

Energy Technology Data Exchange (ETDEWEB)

Scheier, P; Maerk, T [eds.

2002-07-01

The XIII symposium on Atomic and Surface Physics and related Topics (SASP) is devoted to cover the research of interactions between ions, electrons, photons, atoms, molecules and clusters and their interaction with surfaces. This year there was a special session dedicated to proton transfer reaction mass spectrometry covering its applications in different fields and a mini symposium on the radiation action on bio-molecules such as uracil. The contributions included in the proceeding correspond to invited lectures and poster sessions, consisting of short and extended abstracts as well as short articles. (nevyjel)

SASP. Contributions to the 13. Symposium on atomic and surface physics and related topics

International Nuclear Information System (INIS)

Scheier, P.; Maerk, T.

2002-01-01

The XIII symposium on Atomic and Surface Physics and related Topics (SASP) is devoted to cover the research of interactions between ions, electrons, photons, atoms, molecules and clusters and their interaction with surfaces. This year there was a special session dedicated to proton transfer reaction mass spectrometry covering its applications in different fields and a mini symposium on the radiation action on bio-molecules such as uracil. The contributions included in the proceeding correspond to invited lectures and poster sessions, consisting of short and extended abstracts as well as short articles. (nevyjel)

Problems of technology and corrosion in sodium coolant and cover gas

International Nuclear Information System (INIS)

Kuenstler, K.; Ullmann, H.

1977-07-01

The meeting encloses the following themes: (i) Reactions in the system sodium-steel-cover gas (ii) Corrosion behaviour of structural and cladding materials (iii) Determination of impurities in sodium and cover gas (iv) Technology of sodium and cover gas (v) Testing equipments (vi) Safety problems

Nuclear Energy Enabling Technologies (NEET) Reactor Materials: News for the Reactor Materials Crosscut, May 2016

Energy Technology Data Exchange (ETDEWEB)

Maloy, Stuart Andrew [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Materials Science in Radiation and Dynamics Extremes

2016-09-26

In this newsletter for Nuclear Energy Enabling Technologies (NEET) Reactor Materials, pages 1-3 cover highlights from the DOE-NE (Nuclear Energy) programs, pages 4-6 cover determining the stress-strain response of ion-irradiated metallic materials via spherical nanoindentation, and pages 7-8 cover theoretical approaches to understanding long-term materials behavior in light water reactors.

Special topics in the theory of piezoelectricity

CERN Document Server

Yang, Jiashi

2009-01-01

Piezoelectricity has been a steadily growing field, with recent advances made by researchers from applied physics, acoustics, materials science, and engineering. This collective work presents a comprehensive treatment of selected advanced topics in the subject. The book is written for an intermediate graduate level and is intended for researchers, mechanical engineers, and applied mathematicians interested in the advances and new applications in piezoelectricity.

Optical systems for synchrotron radiation. Lecture 1. Introductory topics. Revision

International Nuclear Information System (INIS)

Howells, M.R.

1986-02-01

Various fundamental topics are considered which underlie the design and use of optical systems for synchrotron radiation. The point of view of linear system theory is chosen which acts as a unifying concept throughout the series. In this context the important optical quantities usually appear as either impulse response functions (Green's functions) or frequency transfer functions (Fourier Transforms of the Green's functions). Topics include the damped harmonic oscillator, free-space optical field propagation, optical properties of materials, dispersion, and the Kramers-Kronig relations

Topics in cement and concrete research

OpenAIRE

Brouwers, Jos; Russel, M.I.; Basheer, P.A.M.

2007-01-01

The present paper addresses several topics in regard to the sustainable design and use of concrete. First, major features concerning the sustainable aspects of the material concrete are summarised. Then the major constituent, from an environmental point of view, cement is discussed in detail, particularly the hydration and application of slag cement. The intelligent combining of mineral oxides, which are found in clinker, slag, fly ashes etc., is designated as mineral oxide engineering. It re...

Materials 2014: a great success for materials sector

International Nuclear Information System (INIS)

Isnard, Olivier; Crepin, Jerome

2014-01-01

In this work are presented the summaries of the 19 symposiums presented at the conference: 'Materials 2014' and whose topics were: eco-materials, materials for energy storage and conversion, strategic materials, rare elements and recycling, surfaces functionalization and physico-chemical characterization, interfaces and coatings, corrosion, aging, durability, damage mechanical behaviours, disordered materials, glasses and their functionalization, materials and health, functional materials, porous, granular and with a high surface area materials, nano-materials, nano-structured systems, assembling processes, carbonaceous materials, great instruments and studies of materials, materials in severe conditions, powder forming processes, metallic materials and structures lightening. (O.M.)

Proceedings of the national symposium on materials and processing: functional glass/glass-ceramics, advanced ceramics and high temperature materials

International Nuclear Information System (INIS)

Ghosh, A.; Sahu, A.K.; Viswanadham, C.S.; Ramanathan, S.; Hubli, R.C.; Kothiyal, G.P.

2012-10-01

With the development of materials science it is becoming increasingly important to process some novel materials in the area of glass, advanced ceramics and high temperature metals/alloys, which play an important role in the realization of many new technologies. Such applications demand materials with tailored specifications. Glasses and glass-ceramics find exotic applications in areas like radioactive waste storage, optical communication, zero thermal expansion coefficient telescopic mirrors, human safety gadgets (radiation resistance windows, bullet proof apparels, heat resistance components etc), biomedical (implants, hyperthermia treatment, bone cement, bone grafting etc). Advanced ceramic materials have been beneficial in biomedical applications due to their strength, biocompatibility and wear resistance. Non-oxide ceramics such as carbides, borides, silicides, their composites, refractory metals and alloys are useful as structural and control rod components in high temperature fission/ fusion reactors. Over the years a number of novel processing techniques like selective laser melting, microwave heating, nano-ceramic processing etc have emerged. A detailed understanding of the various aspects of synthesis, processing and characterization of these materials provides the base for development of novel technologies for different applications. Keeping this in mind and realizing the need for taking stock of such developments a National Symposium on Materials and Processing -2012 (MAP-2012) was planned. The topics covered in the symposium are ceramics, glass/glass-ceramics and metals and materials. Papers relevant to INIS are indexed separately

Fusion reactor materials

Energy Technology Data Exchange (ETDEWEB)

none,

1989-01-01

This paper discuses the following topics on fusion reactor materials: irradiation, facilities, test matrices, and experimental methods; dosimetry, damage parameters, and activation calculations; materials engineering and design requirements; fundamental mechanical behavior; radiation effects; development of structural alloys; solid breeding materials; and ceramics.

Fusion reactor materials

International Nuclear Information System (INIS)

1989-01-01

This paper discuses the following topics on fusion reactor materials: irradiation, facilities, test matrices, and experimental methods; dosimetry, damage parameters, and activation calculations; materials engineering and design requirements; fundamental mechanical behavior; radiation effects; development of structural alloys; solid breeding materials; and ceramics

EFFECTS OF EDGE COVERING ON TENSILE STRENGTH OF MDF

Directory of Open Access Journals (Sweden)

Yalçın ÖRS

1999-03-01

Full Text Available Dowels, 6, 8 and 10 mm ? diameters were bonded with PVAc adhesive on Medium Density Fiberboard (MDF. Edges were covered with 5, 8 and 12 mm beech wood materials, drilled 25 mm depth. Tensile strength measurments were made on the samples. The highest tensile strength value was given as 6 mm ? dowel and MDF covered with 8 mm thickness beech wood material (2.294 N/mm2, the lowest value was obtained with 10 mm ? dowel and with unprocessed MDF (1.314 N/mm2.

Nanomaterials for Polymer Electrolyte Membrane Fuel Cells; Materials Challenges Facing Electrical Energy Storate

Energy Technology Data Exchange (ETDEWEB)

Gopal Rao, MRS Web-Editor; Yury Gogotsi, Drexel University; Karen Swider-Lyons, Naval Research Laboratory

2010-08-05

Symposium T: Nanomaterials for Polymer Electrolyte Membrane Fuel Cells Polymer electrolyte membrane (PEM) fuel cells are under intense investigation worldwide for applications ranging from transportation to portable power. The purpose of this seminar is to focus on the nanomaterials and nanostructures inherent to polymer fuel cells. Symposium topics will range from high-activity cathode and anode catalysts, to theory and new analytical methods. Symposium U: Materials Challenges Facing Electrical Energy Storage Electricity, which can be generated in a variety of ways, offers a great potential for meeting future energy demands as a clean and efficient energy source. However, the use of electricity generated from renewable sources, such as wind or sunlight, requires efficient electrical energy storage. This symposium will cover the latest material developments for batteries, advanced capacitors, and related technologies, with a focus on new or emerging materials science challenges.

Clay minerals: Properties and applications to dermocosmetic products and perspectives of natural raw materials for therapeutic purposes-A review.

Science.gov (United States)

Moraes, Jemima Daniela Dias; Bertolino, Silvana Raquel Alina; Cuffini, Silvia Lucia; Ducart, Diego Fernando; Bretzke, Pedro Eriberto; Leonardi, Gislaine Ricci

2017-12-20

Clay minerals are layered materials with a number of peculiar properties, which find many relevant applications in various industries. Since they are easily found everywhere, they are particularly attractive due to their economic viability. In the cosmetic industry, clay minerals are often used as excipients to stabilize emulsions or suspensions and to modify the rheological behavior of these systems. They also play an important role as adsorbents or absorbents, not only in cosmetics but also in other industries, such as pharmaceuticals. This reviewer believes that since this manuscript is presented as covering topical applications that include pharmaceuticals, some types of clay minerals should be considered as a potential material to be used as drug delivery systems. We review several applications of clay minerals to dermocosmetic products, relating them to the underlying properties of these materials and exemplifying with a number of clay minerals available in the market. We also discuss the use of clay minerals in topically-applied products for therapeutic purposes, specially for skin treatment and protection. Copyright © 2017 Elsevier B.V. All rights reserved.

Linear algebra and matrices topics for a second course

CERN Document Server

Shapiro, Helene

2015-01-01

Linear algebra and matrix theory are fundamental tools for almost every area of mathematics, both pure and applied. This book combines coverage of core topics with an introduction to some areas in which linear algebra plays a key role, for example, block designs, directed graphs, error correcting codes, and linear dynamical systems. Notable features include a discussion of the Weyr characteristic and Weyr canonical forms, and their relationship to the better-known Jordan canonical form; the use of block cyclic matrices and directed graphs to prove Frobenius's theorem on the structure of the eigenvalues of a nonnegative, irreducible matrix; and the inclusion of such combinatorial topics as BIBDs, Hadamard matrices, and strongly regular graphs. Also included are McCoy's theorem about matrices with property P, the Bruck-Ryser-Chowla theorem on the existence of block designs, and an introduction to Markov chains. This book is intended for those who are familiar with the linear algebra covered in a typical first c...

Topical understandings of nuclear material measurement · accountancy and quality assurance

International Nuclear Information System (INIS)

Kikuchi, Masahiro; Muraoka, Susumu; Osabe, Takeshi; Terada, Hiromi; Shimizu, Kenichi; Ohtani, Tetsuo; Fujimaki, Kazunori; Ishikawa, Tadatsugu; Shinohara, Yoshinori

2002-01-01

Nuclear material measurement is an important measure to determine the amount of nuclear material of each stage such as receipt, shipment, inventory and hold-up. The material accountancy based on the material balance among the measurements is a measure to control of nuclear material. The material accountancy, from the technical aspect, can be used as promising measures for purposes from operator's level to state's level such as the nuclear safety, property control and environmental preservation other than safeguards measures only to conclude no diversion of nuclear material. This paper discusses various purposes of nuclear material measurements and clarifies the certain function such as quality assurance to be expected at each purpose. Based on the discussion, critical points for the quality assurance of each stage are studied. (author)

46{sup th} Annual meeting on nuclear technology (AMNT 2015). Key topic / Enhanced safety and operation excellence / Sustainable reactor operation management - safe, efficient, valuable

Energy Technology Data Exchange (ETDEWEB)

Fischer, Erwin [E.ON Kernkraft GmbH, Global Unit Next Generation, Hannover (Germany)

2015-08-15

Summary report on the following Topical Session of the 46{sup th} Annual Conference on Nuclear Technology (AMNT 2015) held in Berlin, 5 to 7 May 2015: - Sustainable Reactor Operation Management - Safe, Efficient, Valuable (Erwin Fischer) The other Sessions of the Key Topics - ''Outstanding Know-How and Sustainable Innovations'', - ''Enhanced Safety and Operation Excellence'' and - ''Decommissioning Experience and Waste Management Solutions'' have been covered in atw 7 (2015) and will be covered in further issues of atw.

Esprit HR mattress cover in pressure ulcer prevention.

Science.gov (United States)

Khoulowa, J

Modern mattresses provide soft dense foam, which permits the redistribution of pressure on the patient over a wider area - away from bony prominences where pressure ulcers usually occur. The material used in producing multistretch covers for the new mattresses had a tendency to delaminate as a result of a combination of heat, moisture and inappropriate cleansing techniques causing the water barriers to fall. In partnership with York Health NHS Trust and the material manufacturer, STM Healthcare produced a mattress cover (Esprit HR) which was able to withstand higher pressure from heat and moisture and greatly extended the life expectancy of the Esprit HR mattress.

Regulatory cross-cutting topics for fuel cycle facilities.

Energy Technology Data Exchange (ETDEWEB)

Denman, Matthew R.; Brown, Jason; Goldmann, Andrew Scott; Louie, David

2013-10-01

This report overviews crosscutting regulatory topics for nuclear fuel cycle facilities for use in the Fuel Cycle Research & Development Nuclear Fuel Cycle Evaluation and Screening study. In particular, the regulatory infrastructure and analysis capability is assessed for the following topical areas: Fire Regulations (i.e., how applicable are current Nuclear Regulatory Commission (NRC) and/or International Atomic Energy Agency (IAEA) fire regulations to advance fuel cycle facilities) Consequence Assessment (i.e., how applicable are current radionuclide transportation tools to support risk-informed regulations and Level 2 and/or 3 PRA) While not addressed in detail, the following regulatory topic is also discussed: Integrated Security, Safeguard and Safety Requirement (i.e., how applicable are current Nuclear Regulatory Commission (NRC) regulations to future fuel cycle facilities which will likely be required to balance the sometimes conflicting Material Accountability, Security, and Safety requirements.)

Topics raised by the summary report of the first review meeting

International Nuclear Information System (INIS)

2001-01-01

This document presents the fulfilling of the Brazilian obligations under the Convention on Nuclear Safety. The Chapter 7 of the document contains topics raised by the summary report of the first review meeting. The chapter covers status and position of the regulatory body, collective doses, effluents release trends, adoption of the ICRP 60 and basic safety standards, regulatory strategy, quality assurance, monitoring safety management, international cooperation, probabilistic safety assessment and safety improvement programmes

Topics in extragalactic astronomy with special reference to the southern hemisphere

International Nuclear Information System (INIS)

Vaucouleurs, G. De

1977-01-01

The following topics are covered: classification of galaxies; photometry, colorimetry, spectrophotometry of galaxies; type I supernovae as checks of cosmological models; diameters of galaxies; extragalactic distance indicators; Local Group and nearby group of galaxies; structure of the Local Supercluster of galaxies; anisotropy of the redshifts and kinematics of the Local Supercluster; large scale distribution of galaxies and clusters of galaxies; galaxy counts and probes in depth; problems in the southern hemisphere. (U.K.)

Membrane materials based on polyheteroarylenes and their application for pervaporation

International Nuclear Information System (INIS)

Pulyalina, A Yu; Polotskaya, G A; Toikka, A M

2016-01-01

Studies on the transport properties of membrane materials are topical in connection with the need to solve the fundamental problems and to analyze the applied aspects of the theory of membrane separation processes including, in particular, the development of the energy- and resource-saving, environmentally safe technologies. The aim of the review is to generalize the experimental data on the separation of practically valuable mixtures using membranes based on polyheteroarylenes (thermally stable and mechanically strong polymers). First of all, our analysis covers publications that give a detailed description of the physicochemical properties of the membranes and an interpretation of the specific features of mass transfer during pervaporation of liquid mixtures using membrane materials based on polyheteroarylenes. The dependences of the transport parameters of pervaporation on the process conditions and on the methods for production of membrane materials are discussed. The data presented may be useful for the development of the theory of membrane processes taking into account the chemical nature and physicochemical features of polymeric membrane materials. The bibliography includes 151 references

8th RILEM International Symposium on Testing and Characterization of Sustainable and Innovative Bituminous Materials

CERN Document Server

Partl, Manfred

2016-01-01

This work presents the results of RILEM TC 237-SIB (Testing and characterization of sustainable innovative bituminous materials and systems). The papers have been selected for publication after a rigorous peer review process and will be an invaluable source to outline and clarify the main directions of present and future research and standardization for bituminous materials and pavements. The following topics are covered: - Characterization of binder-aggregate interaction - Innovative testing of bituminous binders, additives and modifiers - Durability and aging of asphalt pavements - Mixture design and compaction analysis - Environmentally sustainable materials and technologies - Advances in laboratory characterization of bituminous materials - Modeling of road materials and pavement performance prediction - Field measurement and in-situ characterization - Innovative materials for reinforcement and interlayer systems - Cracking and damage characterization of asphalt pavements - Rec...

Topic Modeling of NASA Space System Problem Reports: Research in Practice

Science.gov (United States)

Layman, Lucas; Nikora, Allen P.; Meek, Joshua; Menzies, Tim

2016-01-01

Problem reports at NASA are similar to bug reports: they capture defects found during test, post-launch operational anomalies, and document the investigation and corrective action of the issue. These artifacts are a rich source of lessons learned for NASA, but are expensive to analyze since problem reports are comprised primarily of natural language text. We apply topic modeling to a corpus of NASA problem reports to extract trends in testing and operational failures. We collected 16,669 problem reports from six NASA space flight missions and applied Latent Dirichlet Allocation topic modeling to the document corpus. We analyze the most popular topics within and across missions, and how popular topics changed over the lifetime of a mission. We find that hardware material and flight software issues are common during the integration and testing phase, while ground station software and equipment issues are more common during the operations phase. We identify a number of challenges in topic modeling for trend analysis: 1) that the process of selecting the topic modeling parameters lacks definitive guidance, 2) defining semantically-meaningful topic labels requires nontrivial effort and domain expertise, 3) topic models derived from the combined corpus of the six missions were biased toward the larger missions, and 4) topics must be semantically distinct as well as cohesive to be useful. Nonetheless,topic modeling can identify problem themes within missions and across mission lifetimes, providing useful feedback to engineers and project managers.

A Descriptive Study of Television News Coverage of Tobacco in the United States: Frequency of Topics, Frames, Exemplars, and Efficacy

Science.gov (United States)

BLAKE, KELLY D.; KAUFMAN, ANNETTE R.; LORENZO, JOSHUA; AUGUSTSON, ERIK M.

2015-01-01

There is a positive correlation between recall of tobacco-related television news and perceived risks of smoking and thoughts about quitting. The authors used Cision US, Inc., to create a sampling frame (N =61,027) of local and national television news coverage of tobacco from October 1, 2008, to September 30, 2009, and to draw a nationally representative sample (N =730) for content analysis. The authors conducted a descriptive study to determine the frequency and proportion of stories containing specified tobacco topics, frames, sources, and action messages, and the valence of the coverage. Valence was generally neutral; 68% of stories took a balanced stance, with 26% having a tenor supportive of tobacco control and 6% opposing tobacco control. The most frequently covered topics included smoking bans (n =195) and cessation (n =156). The least covered topics included hookah (n =1) and menthol (n =0). The majority of coverage lacked quoting any source (n =345); government officials (n =144) were the most quoted sources. Coverage lacked action messages or resources; 29 stories (Television news can be leveraged by health communication professionals to increase awareness of underrepresented topics in tobacco control. PMID:26176379

Grand unification and gravity - selected topics

International Nuclear Information System (INIS)

Zee, A.

1981-09-01

The material given here was presented in lectures delivered at the 4th Kyoto Summer Institute on Grand Unification and Related Topics. It consists of six sections. The sections are: the family problem, fermion mass hierarchy, maximal local symmetry, operator analysis of new physics, dynamically generated gravity, and Kaluza theory and grand unification. The last section contains a (hopefully) pedagogical introduction to Kaluza theory. For pedagogical completeness, several appendices reviewing some elementary notions of differential geometry have been added

The Project for the High Energy Materials Science Beamline at Petra III

International Nuclear Information System (INIS)

Martins, R. V.; Lippmann, T.; Beckmann, F.; Schreyer, A.

2007-01-01

The high energy materials science beamline will be among the first fourteen beamlines planned to be operational in 2009 at the new third generation synchrotron light source Petra III at DESY, Germany. The operation and funding of this beamline is assured by GKSS. 70% of the beamline will be dedicated to materials science. The remaining 30% are reserved for physics and are covered by DESY. The materials science activities will be concentrating on three intersecting topics which are industrial, applied, and fundamental research. The beamline will combine three main features: Firstly, the high flux, fast data acquisition systems, and the beamline infrastructure will allow carrying out complex and highly dynamic in-situ experiments. Secondly, a high flexibility in beam shaping will be available, fully exploiting the high brilliance of the source. Thirdly, the beamline will provide the possibility to merge in one experiment different analytical techniques such as diffraction and tomography

Fifth topical meeting on the technology of fusion energy

International Nuclear Information System (INIS)

1983-04-01

Abstracts are presented of the approximately 250 papers that were presented at the conference. Some of the main topics included the following: (1) next-generation devices, (2) tritium, (3) hybrids, (4) alternate fuels, (5) materials engineering, (6) blanket and first wall engineering, and (7) inertial confinement

Recent topical research on global, energy, health & medical, and tourism economics, and global software: An overview

NARCIS (Netherlands)

C-L. Chang (Chia-Lin); M.J. McAleer (Michael)

2017-01-01

textabstractThe paper presents an overview of recent topical research on global, energy, health & medical, and tourism economics, and global software. We have interpreted "global" in the title of the Journal of Reviews on Global Economics to cover contributions that have a global impact on

Freshman Health Topics

Science.gov (United States)

Hovde, Karen

2011-01-01

This article examines a cluster of health topics that are frequently selected by students in lower division classes. Topics address issues relating to addictive substances, including alcohol and tobacco, eating disorders, obesity, and dieting. Analysis of the topics examines their interrelationships and organization in the reference literature.…

Misuse of topical corticosteroids: A clinical study of adverse effects

Directory of Open Access Journals (Sweden)

Vivek Kumar Dey

2014-01-01

Full Text Available Background: Misuse of topical corticosteroids is a widespread phenomenon among young people in India, especially women. The practice is associated with significant adverse effects and poor awareness of these effects among the general public. Aim: This study was conducted to examine the misuse and adverse effects of topical corticosteroids among the people in Bastar region in Chhattisgarh state of India. Materials and Methods: Data collected from patients presenting with at least one of the adverse effects of topical corticosteroids as the chief complaint, from November 2010 to October 2011. Results: Out of the 6723 new patients, 379 (5.63% had presented with misuse and adverse effects of topical corticosteroids, of whom 78.89% were females. More than 65% of the patients were in the age group 10-29 years. The main reason for using the topical corticosteroids was to lighten skin colour and treat melasma and suntan. Acne (37.99% and telangiectasia (18.99% were the most common adverse effects noted. Conclusions: Misuse of topical corticosteroids has a huge impact on dermatological practice, leading to a significant proportion of visits to the dermatologist. This hydra-headed problem needs multi-dimensional interventions, involving educational, legal and managerial approaches with cooperation from different sectors of society.

Specialists' meeting on heat and mass transfer in the reactor cover gas, Harwell, England, 8-10 October 1985

International Nuclear Information System (INIS)

1986-07-01

The specialists' meeting on ''Heat and Mass Transfer in the Reactor Cover Gas'' was held at Harwell, the United Kingdom, on 8-10 October 1985. It was attended by 24 participants from all IWGFR member-countries: France, the Federal Republic of Germany, India, Italy, Japan, the Union of Soviet Socialist Republics, the United Kingdom and the United States. The meeting was presided over by Dr K. Eickhoff of the United Kingdom. The following topical areas were reviewed and discussed during the meeting: 1. National review presentations on the status of activities on heat and mass transfer in the reactor cover gas - 2 papers; 2. Aerosol dynamics - 4 papers; 3. Aerosol trapping - 2 papers; 4. Heat and mass transfer through cover gas in annuli - 3 papers; 5. Radiative properties - 4 papers; 6. Modelling of cover gas - 4 papers. A separate abstract was prepared for each of these papers. On the basis of papers presented and discussed by participants, session summaries and conclusions were drafted on the above topical areas. These summaries, as well as general conclusions and recommendations of the meeting were reviewed and agreed upon by consensus at the end of the meeting

Student Material for Competency-Based Education Curriculum for Welding.

Science.gov (United States)

Associated Educational Consultants, Inc., Pittsburgh, PA.

This student welding competency-based education curriculum consists of six units dealing with general areas related to trade occupations and nine units covering specific aspects of working with welding equipment and performing welding operations. Topics covered in the first six units are welding opportunities, human relations, safety, basic…

Tunable structural color in organisms and photonic materials for design of bioinspired materials

International Nuclear Information System (INIS)

Fudouzi, Hiroshi

2011-01-01

In this paper, the key topics of tunable structural color in biology and material science are overviewed. Color in biology is considered for selected groups of tropical fish, octopus, squid and beetle. It is caused by nanoplates in iridophores and varies with their spacing, tilting angle and refractive index. These examples may provide valuable hints for the bioinspired design of photonic materials. 1D multilayer films and 3D colloidal crystals with tunable structural color are overviewed from the viewpoint of advanced materials. The tunability of structural color by swelling and strain is demonstrated on an example of opal composites. (topical review)

PATRAM 2004 - The 14th international symposium on the packaging and transportation of radioactive materials. Conference proceedings

International Nuclear Information System (INIS)

2004-01-01

The 14th International Symposium on the Packaging and Transport of Radioactive Materials, PATRAM 2004, was held at the Estrel Convention Center in Berlin, Germany, from 20-24 September 2004. PATRAM '04 was held under the auspices of the German Federal Ministry for Transport, Building and Housing (BMNBW), and was hosted by the German Bundesanstalt fur Materialforschung und -Prufung (BAM). Further, the conference was held in cooperation with the International Atomic Energy Agency (IAEA) and the US Institute for Nuclear Materials Management. As with past PATRAM conferences, this one covered a wide range of topics that are of concern to the nuclear materials transport industry; regulations, operations, technical analyses and testing, design, institutional issues, security, risk assessment and emergency response. Presentation of these topics was provided through a number of fora, plenary presentations, panel presentations, oral presentations, posters and technical tours. Coupled with the opening reception on Monday evening and the coffee breaks, a forum was provided at this PATRAM that allowed all participants ample opportunities to increase their technical knowledge, to learn about compelling issues around the world and to network with colleagues. (orig.)

PATRAM 2004 - The 14th international symposium on the packaging and transportation of radioactive materials. Conference proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

The 14th International Symposium on the Packaging and Transport of Radioactive Materials, PATRAM 2004, was held at the Estrel Convention Center in Berlin, Germany, from 20-24 September 2004. PATRAM '04 was held under the auspices of the German Federal Ministry for Transport, Building and Housing (BMNBW), and was hosted by the German Bundesanstalt fur Materialforschung und -Prufung (BAM). Further, the conference was held in cooperation with the International Atomic Energy Agency (IAEA) and the US Institute for Nuclear Materials Management. As with past PATRAM conferences, this one covered a wide range of topics that are of concern to the nuclear materials transport industry; regulations, operations, technical analyses and testing, design, institutional issues, security, risk assessment and emergency response. Presentation of these topics was provided through a number of fora, plenary presentations, panel presentations, oral presentations, posters and technical tours. Coupled with the opening reception on Monday evening and the coffee breaks, a forum was provided at this PATRAM that allowed all participants ample opportunities to increase their technical knowledge, to learn about compelling issues around the world and to network with colleagues. (orig.)

The role of preventive topical antibiotic treatment prior to intravitreal injection

Directory of Open Access Journals (Sweden)

Elena Vladimirovna Ageeva

2015-06-01

Full Text Available Treatment of wet age-related macular degeneration (AMD requires frequent intravitreal injections of anti-VEGF agents, sometimes on monthly basis during a long period of time. Endophthalmitis is a rare but extremely severe complication of intravitreal injections. As it has been proven before, the flora from the conjunctival surface is the main source for endophthalmitis. Using Povidone-iodine solution (Betadine10 % Povidone-iodine, EGIS PHARMACEUTICALS is the only way to prevent endophthalmitis. The efficacy of it was proven by numerous studies. No evidence exists that topical antibiotiotics prior and after injections could be effective for prevention of endophthalmitis. Purpose: To study the advisability of topical antibiotic application before intravitreal injection. Materials and methods: Under investigation, there were 25 eyes of 25 patients with wet AMD treated by anti-VEGF intravitreal injections. All patients used topical antibiotics 3 days before injection. Conjunctival culture from injection eye was collected three times: before topical antibiotic use; after topical antibiotic use, and after Betadine 5 % application. Results: The rates of Staphylococcus epidermidis before and after topical antibiotic use were approximately equal. However there was no Staphylococcus epidermidis found after Betadine 5 % application. Conclusion: Our study showed the effectiveness of Betadine 5 % solution in conjunctival flora reduction. Use of topical antibiotics 3 days prior intravitreal injections is not effective. Key words: age-related macular degeneration; endophthalmitis; intravitreal injection; topical antibiotics; endophthalmitis prevention.

Materiales Maria Maya: community-based materials development.

Science.gov (United States)

Moran, B C

1982-01-01

Materials Maria Maya (MMM) is a Guatemalan organization which has dedicated itself to making health education more relevant to the rural Mayans who constitute the majority of Guatemala's population. The administration and direction of the project is in the hands of a team of qualified Mayan men and women. Funding is primarily through various charitable international organizations. The content of preexisting health education programs, strongly influenced by the dominant "ladino" Spanish speaking culture was found to be inappropriate to the goal of this program. MMM set about to formulate a new teaching format which would draw upon, rather than trample over, established cultural practices and life styles. By a process of trial and error, involving small scale field tests, a new program format was developed. By questioning local women about perceived priority areas, through the study of morbidity and mortality data, decisions were made as to topics to be covered. Investigators, authors, and artists worked together to form a "materials package" which was then subject to pretesting. Out of this effort, MMM has been able to come up with a method to encourage more effective participative teaching through the use of education materials.

R'07 World Congress - Recovery of materials and energy for resource efficiency

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-07-01

This final congress report summarises the topics dealt with at the R'07 World Congress on the recovery of materials and energy for resource efficiency. The congress was held in 2007 in Davos, Switzerland. Details on the organisation and participants are given and the experts who held plenary lectures are listed. Brief details are given on oral and poster sessions, along with details on how the proceedings of the congress can be obtained. Workshops held at the conference covered the following topics: Plastics recycling, biofuels and E-waste, workshops on zero wastes, scarce metals and the identification and management of social implications over the product life cycle (footprint). An Internet-address where the results of the sessions can be obtained is given along with a summary of excursions and social events held within the framework of the congress. Finally, participant feedback is presented in graphical form.

Academicians' and Practitioners' Views on the Importance of the Topical Content in the First Auditing Course

Science.gov (United States)

Armitage, Jack; Poyzer, Jillian K.

2010-01-01

The research question addressed in this study is to compare and identify differences between academics teaching auditing classes and practicing accountants regarding the importance of topics covered in the first university auditing course. This is accomplished by surveying academics and practitioners regarding their perceptions of the importance…

Evaluating topic models with stability

CSIR Research Space (South Africa)

De Waal, A

2008-11-01

Full Text Available Topic models are unsupervised techniques that extract likely topics from text corpora, by creating probabilistic word-topic and topic-document associations. Evaluation of topic models is a challenge because (a) topic models are often employed...

Topical report review status

International Nuclear Information System (INIS)

1997-08-01

This report provides industry with procedures for submitting topical reports, guidance on how the U.S. Nuclear Regulatory Commission (NRC) processes and responds to topical report submittals, and an accounting, with review schedules, of all topical reports currently accepted for review schedules, of all topical reports currently accepted for review by the NRC. This report will be published annually. Each sponsoring organization with one or more topical reports accepted for review copies

Materials and material testing

International Nuclear Information System (INIS)

Joergens, H.

1978-01-01

A review based on 105 literature quotations is given on the latest state of development in the steel sector and in the field of non-ferrous metals and plastics. The works quoted also include, preparation, working, welding including simulation methods, improvement of weldability, material mechanics (explanation of defects mechanisms by means of fracture mechanics), defect causes (corrosion, erosion, hydrogen influence), mechanical-technological and non-destructive material testing. Examples from the field of reactor building are also given within there topics. (IHOE) [de

Global pattern for the effect of climate and land cover on water yield

Science.gov (United States)

Guoy Zhou; Xiaohua Wei; Xiuzhi Chen; Ping Zhou; Xiaodong Liu; Yin Xiao; Ge Sun; David F. Scott; Shuyidan Zhou; Liusheng Hano; Yongxian Su

2015-01-01

Research results on the effects of land cover change on water resources vary greatly and the topic remains controversial. Here we use published data worldwide to examine the validity of Fuh’s equation, which relates annual water yield (R) to a wetness index (precipitation/ potential evapotranspiration; P/PET) and watershed characteristics (m). We identify two critical...

Peculiarities in covering the requirements for seed material of sorghum crops

Directory of Open Access Journals (Sweden)

С. І. Мельник

2017-12-01

Full Text Available Purpose. To assess the demand for sorghum seed material and sufficiency of domestic seeds. Results. The analysis of the State register for the period of 2002–2012 showed that there was the tendency not only towards increasing quantity of sorghum crops in general but their substitution by hybrids of foreign breeding. During the period from 2002 to 2017, 72 sorghum varieties were entered on the State register in total, among them only 12 varieties were of domestic breeding, the rest 60 was presented by foreign breeding institutions. Investigation results allowed to determine that the production of base and prebase seeds of sorghum in 2010 amounted to 1,3 t, in 2016 was 43 t. During the same period the production of sugar sorghum increased from 0,2 to 12,0 t, grass sorghum – from 4,0 to 83 t. In 2017, requirements of acreage of such crops as grass sorghum and broomcorn were completely satisfied by the amount of grown seeds. At the same time, the need for seeds of sorghum and sugar sorghum can not be covered completely at the expense of domestic varieties reproduction. In 2017, general demand for sorghum seeds was 400,5 t, among which only 42,0 t was of domestic production. The rest demand for seeds will be met at the expense of import of foreign breeding seeds into the country to be grown and prepared for sowing abroad. Conclusions. In the Register of plant varieties suitable for dissemination in Ukraine, there are 72 sorghum varieties among them only 12 varieties were of domestic breeding, that is 17%, as compared to 83% of recommended great sorghum varieties of foreign breeding. In Ukraine, the area occupied by sorghum cultivation was 22,8 thou ha in 2005, up to 2017 it increased to 89,0 thou ha, and accordingly the demand for seeds run up from 102,6 to 400,5 t. The area occupied by the sugar sorghum in 2005 amounted to only 2,6 thou ha, in 2017 – 20,0 thou ha, that accordingly determined increase of demand for seed material from 13,0 to 99

Syntacticized topics in Kurmuk

DEFF Research Database (Denmark)

Andersen, Torben

2015-01-01

This article argues that Kurmuk, a little-described Western Nilotic language, is characterized by a syntacticized topic whose grammatical relation is variable. In this language, declarative clauses have as topic an obligatory preverbal NP which is either a subject, an object or an adjunct....... The grammatical relation of the topic is expressed by a voice-like inflection of the verb, here called orientation. While subject-orientation is morphologically unmarked, object-oriented and adjunct-oriented verbs are marked by a subject suffix or by a suffix indicating that the topic is not subject, and adjunct......-orientation differs from object-orientation by a marked tone pattern. Topic choice largely reflects information structure by indicating topic continuity. The topic also plays a crucial role in relative clauses and in clauses with contrastive constituent focus, in that objects and adjuncts can only be relativized...

Evaluation of Novel Antimicrobial Peptides as Topical Anti-Infectives with Broad Spectrum Activity Against Combat-Related Bacterial and Fungal Wound Infections

Science.gov (United States)

2016-10-01

Inc. Vallejo, CA 94592 REPORT DATE: October 2016 TYPE OF REPORT: Annual PREPARED FOR: U.S. Army Medical Research and Materiel Command Fort...2016 2. REPORT TYPE Annual 3. DATES COVERED 30 Sep 2015 - 29 Sep 2016 4. TITLE AND SUBTITLE Evaluation of Novel Antimicrobial Peptides as Topical...antibiotics and early debridement has been associated with a large reduction in burn wound infections. Current topical antibiotics include

Multiscale modeling of materials. Materials Research Society symposium proceedings: Volume 538

International Nuclear Information System (INIS)

Bulatov, V.V.; Diaz de la Rubia, T.; Phillips, R.; Kaxiras, E.; Ghoniem, N.

1999-01-01

The symposium, Multiscale Modeling of Materials, was held at the 1998 MRS Fall Meeting in Boston, Massachusetts, November 30 to December 3. Though multiple scale models are not new the topic has recently taken on a new sense of urgency. This is in large part due to the recognition that brute force computational approaches often fall short of allowing for direct simulation of both the characteristic structures and temporal processes found in real materials. As a result, a number of hybrid approaches are now finding favor in which ideas borrowed from distinct disciplines or modeling paradigms are unified to produce more powerful techniques. Topics included are modeling dislocation properties and behavior, defect dynamics and microstructural evolution, crystal defects and interfaces, novel methods for materials modeling, and non-crystalline and nanocrystalline materials. Eighty papers have been processed separately for inclusion on the data base

Modeling Non-Linear Material Properties in Composite Materials

Science.gov (United States)

2016-06-28

Technical Report ARWSB-TR-16013 MODELING NON-LINEAR MATERIAL PROPERTIES IN COMPOSITE MATERIALS Michael F. Macri Andrew G...REPORT TYPE Technical 3. DATES COVERED (From - To) 4. TITLE AND SUBTITLE MODELING NON-LINEAR MATERIAL PROPERTIES IN COMPOSITE MATERIALS ...systems are increasingly incorporating composite materials into their design. Many of these systems subject the composites to environmental conditions

Mouse-resistant insulated covers keep pipes from freezing

Energy Technology Data Exchange (ETDEWEB)

Anon.

2010-01-15

Fabric wellhead covers and insulated blankets are commonly used at well sites in the Wyoming coalbed methane field to keep surface pipes from freezing. These materials are often chewed up by mice who build nests close to the warm pipes. The mice attract rattlesnakes, a potentially serious problem for the workmen who check the wells daily. Kennon Products of Sheridan, Wyoming solved this problem by making a flexible covering material that has a coating of hardened guard plates that prevents mice from chewing through it. More than a hundred of Kennon's mouse-resistant wellhead covers have been used successfully in the gas fields for over a year. They can be installed in less than 30 minutes and cost only a fraction of what a fiberglass hut costs to purchase and install. Huts are being discouraged for use on federal lands because they alter the nesting patterns of eagles, who perch upon them to hunt rodents. Huts also trap methane gas, which is a potential safety hazard. Kennon's mouse-resistant wellhead covers are lower than the fiberglass huts and blend into the landscape. The company is working on camouflage colours to make wellheads less noticeable. In the future, the company plans to insulate water pipes. 1 fig.

Compendium of information on identification and testing of materials for plastic solar thermal collectors

Energy Technology Data Exchange (ETDEWEB)

McGinniss, V.D.; Sliemers, F.A.; Landstrom, D.K.; Talbert, S.G.

1980-07-31

This report is intended to organize and summarize prior and current literature concerning the weathering, aging, durability, degradation, and testing methodologies as applied to materials for plastic solar thermal collectors. Topics covered include (1) rate of aging of polymeric materials; (2) environmental factors affecting performance; (3) evaluation and prediction of service life; (4) measurement of physical and chemical properties; (5) discussion of evaluation techniques and specific instrumentation; (6) degradation reactions and mechanisms; (7) weathering of specific polymeric materials; and (8) exposure testing methodology. Major emphasis has been placed on defining the current state of the art in plastics degradation and on identifying information that can be utilized in applying appropriate and effective aging tests for use in projecting service life of plastic solar thermal collectors. This information will also be of value where polymeric components are utilized in the construction of conventional solar collectors or any application where plastic degradation and weathering are prime factors in material selection.

2nd Topical Workshop on Laser Technology and Optics Design

CERN Document Server

2013-01-01

Lasers have a variety of applications in particle accelerator operation and will play a key role in the development of future particle accelerators by improving the generation of high brightness electron and exotic ion beams and through increasing the acceleration gradient. Lasers will also make an increasingly important contribution to the characterization of many complex particle beams by means of laser-based beam diagnostics methods. The second LANET topical workshop will address the key aspects of laser technology and optics design relevant to laser application to accelerators. The workshop will cover general optics design, provide an overview of different laser sources and discuss methods to characterize beams in details. Participants will be able to choose from a range of topical areas that go deeper in more specific aspects including tuneable lasers, design of transfer lines, noise sources and their elimination and non-linear optics effects. The format of the workshop will be mainly training-based wit...

Melanoma or Pseudo melanoma Change in a pigmented lesion after application of topical 5-Fluorouracil

Science.gov (United States)

2017-10-26

2. REPORT TYPE 3. DATES COVERED (From - To) 10/26/2017 Poster 10/26/2017-10/29/2017 4. TITLE AND SUBTITLE 5a. CONTRACT NUMBER Melanoma or Pseudo...melanoma? Change in a pigmented lesion after application of topical 5-Fluorouracil. 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d

Car Covers | Outdoor Covers Canada

OpenAIRE

Covers, Outdoor

2018-01-01

Protect your car from the elements with Ultimate Touch Car Cover. The multi-layer non-woven fabric is soft on the finish and offers 4 seasons all weather protection.https://outdoorcovers.ca/car-covers/

Effects of mixing and covering with mature compost on gaseous emissions during composting.

Science.gov (United States)

Luo, Wen Hai; Yuan, Jing; Luo, Yi Ming; Li, Guo Xue; Nghiem, Long D; Price, William E

2014-12-01

This study investigated effects of mature compost on gaseous emissions during composting using pig manure amended with corn stalks. Apart from a control treatment, three treatments were conducted with the addition of 5% (wet weight of raw materials) of mature compost: (a) mixing raw materials with mature compost at the beginning of composting; (b) covering raw materials with mature compost throughout the experimental period; and (c) covering raw materials with mature compost at the start of composting, but incorporating it into composting pile on day 6 of composting. Mature compost used for the last treatment was inoculated with 2% (wet weight) of raw materials of strain M5 (a methanotrophic bacterium) solution. During 30-d of composting, three treatments with the addition of mature compost could reduce CH4 emission by 53-64% and N2O emission by 43-71%. However, covering with mature compost throughout the experimental period increased cumulative NH3 emission by 61%, although it could reduce 34% NH3 emission in the first 3d. Inoculating strain M5 in mature compost covered on the top of composting pile within first 6d enhanced CH4 oxidation, but simultaneously increased N2O emission. In addition, mixing with mature compost could improve compost maturity. Given the operational convenience in practice, covering with mature compost and then incorporating it into composting pile is a suitable approach to mitigate gaseous emissions during composting. Copyright © 2014. Published by Elsevier Ltd.

Topical Drugs for Pain Relief

Directory of Open Access Journals (Sweden)

Anjali Srinivasan

2015-03-01

Full Text Available Topical therapy helps patients with oral and perioral pain problems such as ulcers, burning mouth syndrome, temporomandibular disorders, neuromas, neuropathies and neuralgias. Topical drugs used in the field of dentistry are topical anaesthetics, topical analgesics, topical antibiotics and topical corticosteroids. It provides symptomatic/curative effect. Topical drugs are easy to apply, avoids hepatic first pass metabolism and more sites specific. But it can only be used for medications that require low plasma concentrations to achieve a therapeutic effect.

Irradiation environment and materials behavior

International Nuclear Information System (INIS)

Ishino, Shiori

1992-01-01

Irradiation environment is unique for materials used in a nuclear energy system. Material itself as well as irradiation and environmental conditions determine the material behaviour. In this review, general directions of research and development of materials in an irradiation environment together with the role of materials science are discussed first, and then recent materials problems are described for energy systems which are already existing (LWR), under development (FBR) and to be realized in the future (CTR). Topics selected are (1) irradiation embrittlement of pressure vessel steels for LWRs, (2) high fluence performance of cladding and wrapper materials for fuel subassemblies of FBRs and (3) high fluence irradiation effects in the first wall and blanket structural materials of a fusion reactor. Several common topics in those materials issues are selected and discussed. Suggestions are made on some elements of radiation effects which might be purposely utilized in the process of preparing innovative materials. (J.P.N.) 69 refs

Window and dome technologies and materials; Proceedings of the Meeting, Orlando, FL, Mar. 27-29, 1989

Science.gov (United States)

Klocek, Paul

1989-09-01

Papers on window and dome technologies and methodologies are presented, covering the processing and application of window and dome materials such as polycrystalline MgAl2O4 spinel, yttria and lanthana-doped yttria, transparent aluminum oxynitride, sapphire materials, fluoride glass, zinc sulfide, and germanium materials. Other topics include high modulus layers as protective coatings for window materials, ultrahard coatings for IR materials, IR applications of GeC thin filems, CVD diamond for IR applications, amorphic diamond films grown with a laser-ion source, dome cooling, microwave shielding effectiveness of electrically conductive coated optical windows, and the window evaluation program for an airborne FLIR system. In addition, papers are presented on modeling optical properties of window materials, lattice symmetries and thermal expansion, rain damage protection for IR materials, optical window materials for hypersonic flow, the IR emission due to aerodynamic heating of missile domes, a ZnS window for the IR instrumentation system, hypersonic aerooptical effects, optical and semiconductor properties of lead telluride coatings, boron phosphide for coating IR transparencies, and the measurement of high out-of-band filter rejection characteristics.

Land cover fire proneness in Europe

Directory of Open Access Journals (Sweden)

Mario Gonzalez Pereira

2014-12-01

Full Text Available Aim of study: This study aims to identify and characterize the spatial and temporal evolution of the types of vegetation that are most affected by forest fires in Europe. The characterization of the fuels is an important issue of the fire regime in each specific ecosystem while, on the other hand, fire is an important disturbance for global vegetation dynamics.Area of study: Southern European countries: Portugal, Spain, France, Italy and Greece.Material and Methods: Corine Land Cover maps for 2000 and 2006 (CLC2000, CLC2006 and burned area (BA perimeters, from 2000 to 2013 in Europe are combined to access the spatial and temporal evolution of the types of vegetation that are most affected by wild fires using descriptive statistics and Geographical Information System (GIS techniques.Main results: The spatial and temporal distribution of BA perimeters, vegetation and burnt vegetation by wild fires was performed and different statistics were obtained for Mediterranean and entire Europe, confirming the usefulness of the proposed land cover system. A fire proneness index is proposed to assess the fire selectivity of land cover classes. The index allowed to quantify and to compare the propensity of vegetation classes and countries to fire.Research highlights: The usefulness and efficiency of the land cover classification scheme and fire proneness index. The differences between northern Europe and southern Europe and among the Mediterranean region in what concerns to vegetation cover, fire incidence, area burnt in land cover classes and fire proneness between classes for the different countries.Keywords: Fire proneness; Mixed forests; Land cover/land use; Fire regime; Europe; GIS; Corine land cover. 

Advanced topics in control and estimation of state-multiplicative noisy systems

CERN Document Server

Gershon, Eli

2013-01-01

Advanced Topics in Control and Estimation of State-Multiplicative Noisy Systems begins with an introduction and extensive literature survey. The text proceeds to cover solutions of measurement-feedback control and state problems and the formulation of the Bounded Real Lemma for both continuous- and discrete-time systems. The continuous-time reduced-order and stochastic-tracking control problems for delayed systems are then treated. Ideas of nonlinear stability are introduced for infinite-horizon systems, again, in both the continuous- and discrete-time cases. The reader is introduced to six practical examples of noisy state-multiplicative control and filtering associated with various fields of control engineering. The book is rounded out by a three-part appendix containing stochastic tools necessary for a proper appreciation of the text: a basic introduction to nonlinear stochastic differential equations and aspects of switched systems and peak to peak  optimal control and filtering. Advanced Topics in Contr...

Conceptual design of a cover system for the degmay uranium tailings site

Energy Technology Data Exchange (ETDEWEB)

Vatsidin, Saidov; David, S. Kessel; Kim, Chang Lak [KEPCO International Nuclear Graduate School, Ulsan (Korea, Republic of)

2016-06-15

The Republic of Tajikistan has ten former uranium mining sites. The total volume of all tailings is approximately 55 million tonnes, and the covered area is more than 200 hectares. The safe management of legacy uranium mining and tailing sites has become an issue of concern. Depending on the performance requirements and site-specific conditions (location in an arid, semiarid or humid region), a cover system for uranium tailings sites could be constructed using several material layers using both natural and man-made materials. The purpose of this study is to find a feasible cost-effective cover system design for the Degmay uranium tailings site which could provide a long period (100 years) of protection. The HELP computer code was used in the evaluation of potential Degmay cover system designs. As a result of this study, a cover system with 70 cm thick percolation layer, 30 cm thick drainage layer, geomembrane liner and 60 cm thick barrier soil layer is recommended because it minimizes cover thickness and would be the most cost-effective design.

Ultrastructure and 3H-TdR autoradiography after topical application of aromatic retinoid in guinea pigs

International Nuclear Information System (INIS)

Ueda, Keiichi; Maruo, Mitsuru; Inoue, Yuji; Wakabayashi, Shunji

1981-01-01

Histological, autoradiographical and electron microscopical investigations were performed on the epidermis of guinea pigs after topical application of 0.1% aromatic retinoid ointment for 7 days. Histologically, the epidermis exhibited a thickening of granular layer and acanthosis, without a prolonged rete ridge. Labelling indices were 3 to 4 times higher than in the control epidermis. Electron microscopically, the nuclei in the spinous and the basal layer were large in size and nucleoli were increased in number. In the cytoplasm, tonofilaments were reduced in number and lots of vacuoles containing less dense amorphous material appeared. Amorphous material was present in the intercellular spaces of the epidermis. Differentiation and proliferation of the epidermis in guinea pigs after topical application of aromatic retinoid showed almost the same response in quantity to the epidermis after topical application of retinoic acid, while the epidermal alternation was slight in degree than in the epidermis after topical application of retinoic acid. (author)

Topics in multivariate approximation and interpolation

CERN Document Server

Jetter, Kurt

2005-01-01

This book is a collection of eleven articles, written by leading experts and dealing with special topics in Multivariate Approximation and Interpolation. The material discussed here has far-reaching applications in many areas of Applied Mathematics, such as in Computer Aided Geometric Design, in Mathematical Modelling, in Signal and Image Processing and in Machine Learning, to mention a few. The book aims at giving a comprehensive information leading the reader from the fundamental notions and results of each field to the forefront of research. It is an ideal and up-to-date introduction for gr

eHealth Technologies as an Intervention to Improve Adherence to Topical Antipsoriatics

DEFF Research Database (Denmark)

Svendsen, Mathias Tiedemann; Andersen, Flemming; Andersen, Klaus Ejner

2018-01-01

BACKGROUND: Topical antipsoriatics are recommended first-line treatment of psoriasis, but rates of adherence are low. Patient support by use of electronic health (eHealth) services is suggested to improve medical adherence. OBJECTIVE: To review randomised controlled trials (RCTs) testing eHealth...... interventions designed to improve adherence to topical antipsoriatics and to review applications for smartphones (apps) incorporating the word psoriasis. MATERIAL AND METHODS: Literature review: Medline, Embase, Cochrane, PsycINFO, and Web of Science were searched using search terms for eHealth, psoriasis....... CONCLUSION: There is a critical need for high-quality RCTs testing if the ubiquitous eHealth technologies, e.g. some of the numerous apps, can improve psoriasis patients' rates of adherence to topical antipsoriatics....

BOOK REVIEW: Heterogeneous Materials I and Heterogeneous Materials II

Science.gov (United States)

Knowles, K. M.

2004-02-01

In these two volumes the author provides a comprehensive survey of the various mathematically-based models used in the research literature to predict the mechanical, thermal and electrical properties of hetereogeneous materials, i.e., materials containing two or more phases such as fibre-reinforced polymers, cast iron and porous ceramic kiln furniture. Volume I covers linear properties such as linear dielectric constant, effective electrical conductivity and elastic moduli, while Volume II covers nonlinear properties, fracture and atomistic and multiscale modelling. Where appropriate, particular attention is paid to the use of fractal geometry and percolation theory in describing the structure and properties of these materials. The books are advanced level texts reflecting the research interests of the author which will be of significant interest to research scientists working at the forefront of the areas covered by the books. Others working more generally in the field\

Topical report review status

International Nuclear Information System (INIS)

1982-08-01

A Topical Report Review Status is scheduled to be published semi-annually. The primary purpose of this document is to provide periodic progress reports of on-going topical report reviews, to identify those topical reports for which the Nuclear Regulatory Commission (NRC) staff review has been completed and, to the extent practicable, to provide NRC management with sufficient information regarding the conduct of the topical report program to permit taking whatever actions deemed necessary or appropriate. This document is also intended to be a source of information to NRC Licensing Project Managers and other NRC personnel regarding the status of topical reports which may be referenced in applications for which they have responsibility. This status report is published primarily for internal NRC use in managing the topical report program, but is also used by NRC to advise the industry of report review status

Topical report review status

International Nuclear Information System (INIS)

1983-01-01

A Topical Report Review Status is scheduled to be published semi-annually. The primary purpose of this document is to provide periodic progress reports of on-going topical report reviews, to identify those topical reports for which the Nuclear Regulatory Commission (NRC) staff review has been completed and, to the extent practicable, to provide NRC management with sufficient information regarding the conduct of the topical report program to permit taking whatever actions deemed necessary or appropriate. This document is also intended to be a source of information to NRC Licensing Project Managers and other NRC personnel regarding the status of topical reports which may be referenced in applications for which they have responsibility. This status report is published primarily for internal NRC use in managing the topical report program, but is also used by NRC to advise the industry of report review status

A comparative study of the efficacy of topical negative pressure moist dressings and conventional moist dressings in chronic wounds

Directory of Open Access Journals (Sweden)

Tauro Leo

2007-01-01

Full Text Available Aim: To assess the efficacy of topical negative pressure moist wound dressing as compared to conventional moist wound dressings in improving the healing process in chronic wounds and to prove that negative pressure dressings can be used as a much better treatment option in the management of chronic wounds. Materials and Methods: This is a prospective comparative study of data from 112 patients with chronic wounds, of which 56 patients underwent topical negative pressure dressings (17 diabetic, 10 pressure sores, nine ischemic, two varicose, 10 post-infective raw areas and eight traumatic - six had bone exposed, two orthopaedic prosthesis exposed. The remaining 56 patients underwent conventional moist dressings (20 diabetic, two ischemic, 15 pressure sores, three varicose, eight post-infective raw areas and eight traumatic - five had bone exposed, three orthopaedic prosthesis exposed. The results were compared after 10 days. The variables compared were, rate of granulation tissue formation as a percentage of ulcer area covered, skin graft take up as the percentage of ulcer surface area and duration of hospital stay. The variables were compared using Unpaired Student′s t test. A " P" value < 0.05 was considered significant. Results: Out of 56 patients who underwent topical negative pressure dressings, six (10.71% were failures, due to failure in maintaining topical negative pressure due to defective sealing technique; these were included into the study group. After 10 days, the mean rate of granulation tissue formation was 71.43% of ulcer surface area. All these 56 cases underwent split-thickness skin grafting. The mean graft take-up was 79.29%. The mean hospital stay was 32.64 days. In the remaining 56 patients, the mean rate of granulation tissue formation was 52.85% of ulcer surface area. The mean graft take-up was only 60.45% of the total ulcer surface area. The mean hospital stay was 60.45 days. Conclusion: To conclude, topical negative

75 FR 26647 - Ophthalmic and Topical Dosage Form New Animal Drugs; Ivermectin Topical Solution

Science.gov (United States)

2010-05-12

.... FDA-2010-N-0002] Ophthalmic and Topical Dosage Form New Animal Drugs; Ivermectin Topical Solution... are treated with a topical solution of ivermectin. DATES: This rule is effective May 12, 2010. FOR... ANADA 200-340 for PRIVERMECTIN (ivermectin), a topical solution used on cattle to control infestations...

Preliminary assessment of geologic materials to minimize biological intrusion of low-level waste trench covers and plans for the future

International Nuclear Information System (INIS)

Hakonson, T.E.; White, G.C.; Gladney, E.S.; Muller, M.

1981-01-01

The long-term integrity of low-level waste shallow land burial sites is dependent on the interaction of physical, chemical, and biological factors that modify the waste containment system. Past research on low-level waste shallow land burial methods has emphasized physical (i.e., water infiltration, soil erosion) and chemical (radionuclide leaching) processes that can cause radionuclide transport from a waste site. Preliminary results demonstrate that a sandy backfill material offers little resistance to root and animal intrusion through the cover profile. However, bentonite clay, cobble, and cobble-gravel combinations do reduce plant root and animal intrusion through cover profiles compared with sandy backfill soil. However, bentonite clay barrier systems appear to be degraded by plant roots through time. Desiccation of the clay barrier by invading plant roots may limit the usefulness of bentonite clay as a moisture and/or biological carrier unless due consideration is given to this interaction. Future experiments are described that further examine the effect of plant roots on clay barrier systems and that determine the effectiveness of proposed biological barriers on larger scales and under various stress conditions

Women's Health Topics

Science.gov (United States)

... Information by Audience For Women Women's Health Topics Women's Health Topics Share Tweet Linkedin Pin it More sharing options Linkedin Pin it Email Print National Women's Health Week May 13 - 19, 2018 Join us ...

Developments in functional equations and related topics

CERN Document Server

Ciepliński, Krzysztof; Rassias, Themistocles

2017-01-01

This book presents current research on Ulam stability for functional equations and inequalities. Contributions from renowned scientists emphasize fundamental and new results, methods and techniques. Detailed examples are given to theories to further understanding at the graduate level for students in mathematics, physics, and engineering. Key topics covered in this book include: Quasi means Approximate isometries Functional equations in hypergroups Stability of functional equations Fischer-Muszély equation Haar meager sets and Haar null sets Dynamical systems Functional equations in probability theory Stochastic convex ordering Dhombres functional equation Nonstandard analysis and Ulam stability This book is dedicated in memory of Staniłsaw Marcin Ulam, who posed the fundamental problem concerning approximate homomorphisms of groups in 1940; which has provided the stimulus for studies in the stability of functional equations and inequalities.

Topicality and Text Pragmatic Prominence Five Hierarchies Regarding the Topic Suitability of Nominal Constituents

DEFF Research Database (Denmark)

Korzen, Iørn

2015-01-01

This paper presents and discusses a description of topicality and text pragmatic prominence of nominal discourse referents based on four hierarchies. These hierarchies concern the referent with respect to (a) its identifiability (± identifiable), (b) its referentiality (e.g. deictic, specific...... incorporation of the NP designating the referent, (2) the linguistic material of anaphors linked to the NP, and (3) various phenomena linked to the possible clefting of the NP. The paper also demonstrates that the proposed model and taxonomy is very well suited as tertium comparationis in a cross......-linguistic approach, not least in typological comparisons between for instance Romance and Germanic languages. The correlations described are viewed cross-linguistically with evidence from Italian, Danish, and English....

Materials for Space Exploration

Science.gov (United States)

Robertson, Luke B.; Williams, Martha

2010-01-01

Topics include a lab overview, testing and processing equipment, hemochromic hydrogen sensors, antimicrobial materials, wire system materials, CNT ink formulations, CNT ink dust screens, CNT ink printed circuitry, cryogenic materials development, fire and polymers, the importance of lighting, electric lighting systems, LED for plant growth, and carbon nanotube fiber filaments.

Investigation of layered covers designed to limit infiltration at waste disposal sites

International Nuclear Information System (INIS)

Johnson, T.M.; Herzog, B.L.; Cartwright, K.; Larson, T.H.

1983-01-01

Layered soils of highly contrasting texture have been shown to act as a barrier to infiltration because of differences in unsaturated hydraulic properties. Water infiltrating into a fine-grained soil overlying an unsaturated gravel will not enter the gravel until the overlying material is nearly saturated. As a result of what is commonly called the wick effect, moisture will flow laterally through the fine-grained soil above the gravel layer. Layered covers of compacted soil materials utilizing this phenomenon have been proposed to limit infiltration at waste disposal sites. A study funded by the US Nuclear Regulatory Commission is underway to evaluate the potential use of layered trench covers to minimize infiltration at low-level radioactive waste disposal sites. Moisture movement through layered covers consisting of compacted fine-grained soils and sand or gravel was modeled, using a one-dimensional finite-difference model to compare with laboratory column experiments and a two-dimensional finite-element model for field-scale simulations. Soil-moisture characteristic data were obtained from laboratory experiments and the hydraulic conductivity was calculated as a function of capillary pressure. The numerical simulations indicate that layered covers using various combinations of compacted fine-grained soils and coarse-grained material are able to substantially reduce infiltration. Laboratory column experiments using a dual-gamma ray attenuation system to measure moisture content and density simultaneously have been used to observe the behavior of layered soils and to select materials for field testing. Currently underway are field-scale studies of alternative cover designs selected on the basis of two-dimensional modeling

Design surface covers: an approach to long-term waste site stabilization

International Nuclear Information System (INIS)

Beedlow, P.A.; Cadwell, L.L.; McShane, M.C.

1983-02-01

The wide range of existing environmental conditions, potential contaminants and available cover materials at waste disposal sites necessitates site-specific designing of surface covers for effective long-term erosion resistance. This paper presents a systematic approach to designing surface covers for hazardous waste repositories that can be tailored to conditions at any site. The approach consists of three phases: (1) an assessment, during which the degree of required surface protection (erosion potential) is determined; (2) a preliminary design that integrates surface cover design with the need to minimize transport of contaminants; and (3) a final design, where the cost and effectiveness of the surface cover are determined. 1 figure

Topics in the generalized vector dominance model

International Nuclear Information System (INIS)

Chavin, S.

1976-01-01

Two topics are covered in the generalized vector dominance model. In the first topic a model is constructed for dilepton production in hadron-hadron interactions based on the idea of generalized vector-dominance. It is argued that in the high mass region the generalized vector-dominance model and the Drell-Yan parton model are alternative descriptions of the same underlying physics. In the low mass regions the models differ; the vector-dominance approach predicts a greater production of dileptons. It is found that the high mass vector mesons which are the hallmark of the generalized vector-dominance model make little contribution to the large yield of leptons observed in the transverse-momentum range 1 less than p/sub perpendicular/ less than 6 GeV. The recently measured hadronic parameters lead one to believe that detailed fits to the data are possible under the model. The possibility was expected, and illustrated with a simple model the extreme sensitivity of the large-p/sub perpendicular/ lepton yield to the large-transverse-momentum tail of vector-meson production. The second topic is an attempt to explain the mysterious phenomenon of photon shadowing in nuclei utilizing the contribution of the longitudinally polarized photon. It is argued that if the scalar photon anti-shadows, it could compensate for the transverse photon, which is presumed to shadow. It is found in a very simple model that the scalar photon could indeed anti-shadow. The principal feature of the model is a cancellation of amplitudes. The scheme is consistent with scalar photon-nucleon data as well. The idea is tested with two simple GVDM models and finds that the anti-shadowing contribution of the scalar photon is not sufficient to compensate for the contribution of the transverse photon. It is found doubtful that the scalar photon makes a significant contribution to the total photon-nuclear cross section

Atom probe field ion microscopy and related topics: A bibliography 1993

Energy Technology Data Exchange (ETDEWEB)

Godfrey, R.D.; Miller, M.K.; Russell, K.F.

1994-10-01

This bibliography, covering the period 1993, includes references related to the following topics: atom probe field ion microscopy (APFIM), field emission (FE), and field ion microscopy (FIM). Technique-oriented studies and applications are included. The references contained in this document were compiled from a variety of sources including computer searches and personal lists of publications. To reduce the length of this document, the references have been reduced to the minimum necessary to locate the articles. The references are listed alphabetically by authors, an Addendum of references missed in previous bibliographies is included.

Atom probe field ion microscopy and related topics: A bibliography 1993

International Nuclear Information System (INIS)

Godfrey, R.D.; Miller, M.K.; Russell, K.F.

1994-10-01

This bibliography, covering the period 1993, includes references related to the following topics: atom probe field ion microscopy (APFIM), field emission (FE), and field ion microscopy (FIM). Technique-oriented studies and applications are included. The references contained in this document were compiled from a variety of sources including computer searches and personal lists of publications. To reduce the length of this document, the references have been reduced to the minimum necessary to locate the articles. The references are listed alphabetically by authors, an Addendum of references missed in previous bibliographies is included

Research on clay covering experiment in a abandoned uranium mining area

International Nuclear Information System (INIS)

Zhang Xueli; Xu Lechang; Zhang Wei

2014-01-01

The clay covering experiment was designed in a abandoned uranium mining area, including experiment principle, determining size of experimental site, experiment method, choosing cover materials and determining cover thickness. According to the experiment results, the relationship between the radon exhalation rate and cover thickness, the diffusion coefficient of radon in clay were fully discussed. Also, the corresponding function expressions were established. The linear correlation coefficient test results showed that the relationship between the radon exhalation rate and cover thickness was significantly correlated. According to the correlation function expression between the radon exhalation rate and the cover thickness, the cover thickness of the decommissioning sites can be determined, in order to provide a scientific basis for the design and environmental impact assessment on decommissioning disposal project of a uranium mine. (authors)

7. International conference on materials science and condensed matter physics. Abstracts

International Nuclear Information System (INIS)

2014-09-01

This book includes the abstracts of the communications presented at the 7th International Conference on Materials Science and Condensed Matter Physics, traditional biennial meeting organized by the Institute of Applied Physics of the Academy of Sciences of Moldova (IAP) which celebrates this year its 50th anniversary. The conference reports have been delivered in a broad range of topics in materials science, condensed matter physics, electrochemistry reflecting the research results of the scientific staff and Ph.D. students from the IAP as well as those by distinguished guests from different countries. The abstracts cover special issues of modern theoretical and experimental physics and advanced technology, such as advances in condensed matter theory; theory of low dimensional systems; modelling of materials and structural properties; ordering and phase transitions; quantum optics and electronics; strong correlated electronic systems; crystal growth; electronic processes and transport properties of semiconductors and superconductors; ordering processes in magnetic and multiferroic systems; interaction of light and matter, and optical phenomena; properties of composites, meta materials and molecular materials; crystal engineering of solid state structures; metal-organic materials; porous materials; advanced materials with magnetic, luminescent, nonlinear optical , thermoelectric, catalytic, analytic and pharmaceutical properties; defects engineering and mechanical properties; crystallography of organic, inorganic and supramolecular compounds; advanced physics of nanosystems; methods of nanostructures and nanomaterials fabrication and characterization; electronic properties of quantum wells, superlattices, nanowires and nanodots; meso- and nanoelectronics, optical processes in nanostructures; emerging phenomena in nanocomposites and nanomaterials; device modelling and simulation, device structures and elements; photovoltaics: crystals, thin films, nanoparticles

Powder metallurgical high performance materials. Proceedings. Volume 3: general topics

International Nuclear Information System (INIS)

Kneringer, G.; Roedhammer, P.; Wildner, H.

2001-01-01

The proceedings of these seminars form an impressive chronicle of the continued progress in the understanding of refractory metals and cemented carbides and in their manufacture and application. The 15 th Plansee Seminar was convened under the general theme 'Powder Metallurgy High Performance Materials'. Under this broadened perspective the seminar will strive to look beyond the refractory metals and cemented carbides, which remain at its focus, to novel classes of materials, such as intermetallic compounds, with potential for high temperature applications. (boteke)

40 CFR 761.375 - Specific requirements for surfaces coated or covered with dust, dirt, grime, grease, or another...

Science.gov (United States)

2010-07-01

... coated or covered with dust, dirt, grime, grease, or another absorbent material. 761.375 Section 761.375... coated or covered with dust, dirt, grime, grease, or another absorbent material. (a) First wash. Cover..., absorbent pad until the surface appears dry. This cleaning should remove any residual dirt, dust, grime, or...

Ultrastructure and /sup 3/H-TdR autoradiography after topical application of aromatic retinoid in guinea pigs

Energy Technology Data Exchange (ETDEWEB)

Ueda, K.; Maruo, M.; Inoue, Y.; Wakabayashi, S. (Kyoto Prefectural Univ. of Medicine (Japan))

1981-12-01

Histological, autoradiographical and electron microscopical investigations were performed on the epidermis of guinea pigs after topical application of 0.1% aromatic retinoid ointment for 7 days. Histologically, the epidermis exhibited a thickening of granular layer and acanthosis, without a prolonged rete ridge. Labelling indices were 3 to 4 times higher than in the control epidermis. Electron microscopically, the nuclei in the spinous and the basal layer were large in size and nucleoli were increased in number. In the cytoplasm, tonofilaments were reduced in number and lots of vacuoles containing less dense amorphous material appeared. Amorphous material was present in the intercellular spaces of the epidermis. Differentiation and proliferation of the epidermis in guinea pigs after topical application of aromatic retinoid showed almost the same response in quantity to the epidermis after topical application of retinoic acid, while the epidermal alternation was slight in degree than in the epidermis after topical application of retinoic acid.

Comparative study of oral and topical ketoconazole therapy in pityriasis versicolor

Directory of Open Access Journals (Sweden)

Nagpal V

2003-07-01

Full Text Available Introduction: Both topical and systemic ketoconazole are reported to be effective against pityriasis versicolor. Material and Methods: Forty patients suffering from pityriasis versicolor were treated either with oral ketoconazole 200 mg per day or 2% ketoconazole cream topically once daily for 2 weeks. Results: On global assessment, after 2 weeks of start of therapy, 18 (90% out of 20 patients treated with oral ketoconazole were cured while 2 patients had considerable residual disease. In the ketoconazole cream group, 16 (80% out of 20 patients were cured and 4 patients had considerable residual disease. Conclusion: No significant difference was observed in the response rates in the two groups. Relapse occurred in two patients of the systemic ketoconazole group and six patients of the topical ketoconazole group during the follow-up period of three months.

Applications of nanotechnology in food packaging and food safety: barrier materials, antimicrobials and sensors.

Science.gov (United States)

Duncan, Timothy V

2011-11-01

In this article, several applications of nanomaterials in food packaging and food safety are reviewed, including: polymer/clay nanocomposites as high barrier packaging materials, silver nanoparticles as potent antimicrobial agents, and nanosensors and nanomaterial-based assays for the detection of food-relevant analytes (gasses, small organic molecules and food-borne pathogens). In addition to covering the technical aspects of these topics, the current commercial status and understanding of health implications of these technologies are also discussed. These applications were chosen because they do not involve direct addition of nanoparticles to consumed foods, and thus are more likely to be marketed to the public in the short term. Published by Elsevier Inc.

Topical issues of psychological research materials on matters related to extremism

Directory of Open Access Journals (Sweden)

Sekerazh T.N.

2014-12-01

Full Text Available The article deals with methodological support psychological and linguistic research "extremist" materials. Presents a comprehensive psycho-linguistic approach to the examination of information materials on matters related to combating extremism and terrorism, and certain provisions of the methodology developed by the Russian federal center of judicial examination of the Ministry of Justice of the Russian Federation. Based on the analysis of the "verbal" crimes related to criminal legal interpretation of extremism and terrorism, highlighted the types of prohibited public expression of communicative action, corresponding to the seven types of "extremist" values. The article outlines the key features of psychological analysis "extremist" materials research stages. It is shown that the complex (psycho-linguistic approach to the study of materials of extremist orientation, is scientifically sound, methodically proven, appropriate to the needs of law enforcement, judicial and investigative practice.

Evaluation of contact sensitivity to topical drugs in patients with contact dermatitis

Directory of Open Access Journals (Sweden)

Bilge Bülbül Şen

2013-03-01

Full Text Available Background and Design: Topical drugs are an important group of contact allergens. The present study aimed to evaluate contact sensitivity to topical drugs in patients with contact dermatitis. Materials and Methods: Between 2003 and 2008, 129 patients were followed up at the Department of Dermatology at Ankara University School of Medicine with clinically suspected contact sensitivity to topical drugs. In this study, the patch test reactions to the European Standard Battery and topical drugs used by the patients and medicament patch test results were evaluated. Results: Positive patch test reaction to one or more allergens was found in 80 (62.0% of 129 patients included in the study. Sixty-one of the 80 patients (61/129, 47.3% had positive patch test reaction to medicaments. Medicament sensitivity was detected in 37.9% (49/129 of subjects. Nitrofurazone was found to be the most common allergen (18.6%. Discussion: The present study showed that topical drugs are a frequent cause of allergic contact dermatitis. Therefore, the probability of contact sensitivity to topical drugs should also be considered in patients with the clinical diagnosis of allergic contact dermatitis and, suspected cases should be evaluated further with patch testing in order to find the responsible allergens.

Topic Visualization and Survival Analysis

OpenAIRE

Wang, Ping Jr

2017-01-01

Latent semantic structure in a text collection is called a topic. In this thesis, we aim to visualize topics in the scientific literature and detect active or inactive research areas based on their lifetime. Topics were extracted from over 1 million abstracts from the arXiv.org database using Latent Dirichlet Allocation (LDA). Hellinger distance measures similarity between two topics. Topics are determined to be relevant if their pairwise distances are smaller than the threshold of Hellinger ...

Can Biochar Covers Reduce Emissions from Manure Lagoons While Capturing Nutrients?

Science.gov (United States)

The unique physical and chemical properties of biochars make them promising materials for odor, gas, and nutrient sorption. Floating covers made from organic materials (biocovers) are one option for reducing odor and gas emissions from livestock manure lagoons. This study evaluat...

Modern electronic materials

CERN Document Server

Watkins, John B

2013-01-01

Modern Electronic Materials focuses on the development of electronic components. The book first discusses the history of electronic components, including early developments up to 1900, developments up to World War II, post-war developments, and a comparison of present microelectric techniques. The text takes a look at resistive materials. Topics include resistor requirements, basic properties, evaporated film resistors, thick film resistors, and special resistors. The text examines dielectric materials. Considerations include basic properties, evaporated dielectric materials, ceramic dielectri

Soft material-based microculture system having air permeable cover sheet for the protoplast culture of Nicotiana tabacum.

Science.gov (United States)

Ju, Jong Il; Ko, Jung-Moon; Kim, So Hyeon; Baek, Ju Yeoul; Cha, Hyeon-Cheol; Lee, Sang Hoon

2006-08-01

In plant cell culture, the delivery of nutrition and gas (mainly oxygen) to the cells is the most important factor for viability. In this paper, we propose a polydimethylsiloxane (PDMS)-based microculture system that is designed to have good aeration. PDMS is known to have excellent air permeability, and through the experimental method, we investigated the relation between the degree of air delivery and the thickness of the PDMS sheet covering the culture chamber. We determined the proper thickness of the cover sheet, and cultured protoplasts of Nicotiana tabacum in a culture chamber covered with a PDMS sheet having thickness of 400 microm. The cells were successfully divided, and lived well inside the culture chamber for 10 days. In addition, protoplasts were cultured inside the culture chambers covered with the cover glass and the PDMS sheet, respectively, and the microcolonies were formed well inside the PDMS covered chamber after 10 days.

Biological intrusion of low-level-waste trench covers

International Nuclear Information System (INIS)

Hakonson, T.E.; Gladney, E.S.

1981-01-01

The long-term integrity of low-level waste shallow land burial sites is dependent on the interaction of physical, chemical, and biological factors that modify the waste containment system. Past research on low-level waste shallow land burial methods has emphasized physical (i.e., water infiltration, soil erosion) and chemical (radionuclide leaching) processes that can cause waste site failure and subsequent radionuclide transport. The purpose of this paper is to demonstrate the need to consider biological processes as being potentially important in reducing the integrity of waste burial site cover treatments. Plants and animals not only can transport radionuclides to the ground surface via root systems and soil excavated from the cover profile by animal burrowing activities, but they modify physical and chemical processes within the cover profile by changing the water infiltration rates, soil erosion rates and chemical composition of the soil. One approach to limiting biological intrusion through the waste cover is to apply a barrier within the profile to limit root and animal penetration with depth. Experiments in the Los Alamos Experimental Engineered Test Facility were initiated to develop and evaluate biological barriers that are effective in minimizing intrusion into waste trenches. The experiments that are described employ four different candidate barrier materials of geologic origin. Experimental variables that will be evaluated, in addition to barrier type, are barrier depth and soil overburden depth. The rate of biological intrusion through the various barrier materials is being evaluated through the use of activatable stable tracers

GeneTopics - interpretation of gene sets via literature-driven topic models

Science.gov (United States)

2013-01-01

Background Annotation of a set of genes is often accomplished through comparison to a library of labelled gene sets such as biological processes or canonical pathways. However, this approach might fail if the employed libraries are not up to date with the latest research, don't capture relevant biological themes or are curated at a different level of granularity than is required to appropriately analyze the input gene set. At the same time, the vast biomedical literature offers an unstructured repository of the latest research findings that can be tapped to provide thematic sub-groupings for any input gene set. Methods Our proposed method relies on a gene-specific text corpus and extracts commonalities between documents in an unsupervised manner using a topic model approach. We automatically determine the number of topics summarizing the corpus and calculate a gene relevancy score for each topic allowing us to eliminate non-specific topics. As a result we obtain a set of literature topics in which each topic is associated with a subset of the input genes providing directly interpretable keywords and corresponding documents for literature research. Results We validate our method based on labelled gene sets from the KEGG metabolic pathway collection and the genetic association database (GAD) and show that the approach is able to detect topics consistent with the labelled annotation. Furthermore, we discuss the results on three different types of experimentally derived gene sets, (1) differentially expressed genes from a cardiac hypertrophy experiment in mice, (2) altered transcript abundance in human pancreatic beta cells, and (3) genes implicated by GWA studies to be associated with metabolite levels in a healthy population. In all three cases, we are able to replicate findings from the original papers in a quick and semi-automated manner. Conclusions Our approach provides a novel way of automatically generating meaningful annotations for gene sets that are directly

Organic Synthetic Advanced Materials for Optoelectronic and Energy Applications (at National Taipei University of Technology)

Energy Technology Data Exchange (ETDEWEB)

Yen, Hung-Ju [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Chemistry Division

2016-11-14

These slides cover Hung-Ju Yen's recent work in the synthesis and structural design of functional materials, which were further used for optoelectronic and energy applications, such as lithium ion battery, solar cell, LED, electrochromic, and fuel cells. This was for a job interview at National Taipei University of Technology. The following topics are detailed: current challenges for lithium-ion batteries; graphene, graphene oxide and nanographene; nanographenes with various functional groups; fine tune d-spacing through organic synthesis: varying functional group; schematic view of LIBs; nanographenes as LIB anode; rate performance (charging-discharging); electrochromic technology; electrochromic materials; advantages of triphenylamine; requirement of electrochromic materials for practical applications; low driving voltage and long cycle life; increasing the electroactive sites by multi-step synthetic procedures; synthetic route to starburst triarylamine-based polyamide; electrochromism ranging from visible to NIR region; transmissive to black electrochromism; RGB and CMY electrochromism.

Organic Synthetic Advanced Materials for Optoelectronic and Energy Applications (at Center for Condensed Matter Sciences)

Energy Technology Data Exchange (ETDEWEB)

Yen, Hung-Ju [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Chemistry Division

2016-11-14

These slides cover Hung-Ju Yen's recent work in the synthesis and structural design of functional materials, which were further used for optoelectronic and energy applications, such as lithium ion battery, solar cell, LED, electrochromic, and fuel cells. This was for a job interview at Center for Condensed Matter Sciences. The following topics are detailed: current challenges for lithium-ion batteries; graphene, graphene oxide and nanographene; nanographenes with various functional groups; fine tune d-spacing through organic synthesis: varying functional group; schematic view of LIBs; nanographenes as LIB anode; rate performance (charging-discharging); electrochromic technology; electrochromic materials; advantages of triphenylamine; requirement of electrochromic materials for practical applications; low driving voltage and long cycle life; increasing the electroactive sites by multi-step synthetic procedures; synthetic route to starburst triarylamine-based polyamide; electrochromism ranging from visible to NIR region; transmissive to black electrochromism; RGB and CMY electrochromism.

Organic Synthetic Advanced Materials for Optoelectronic and Energy Applications (at National Sun Yat-sen University) 

Energy Technology Data Exchange (ETDEWEB)

Yen, Hung-Ju [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Chemistry Division

2016-11-14

These slides cover Hung-Ju Yen's recent work in the synthesis and structural design of functional materials, which were further used for optoelectronic and energy applications, such as lithium ion battery, solar cell, LED, electrochromic, and fuel cells. This was for a job interview at National Sun Yat-sen University. The following topics are detailed: current challenges for lithium-ion batteries; graphene, graphene oxide and nanographene; nanographenes with various functional groups; fine tune d-spacing through organic synthesis: varying functional group; schematic view of LIBs; nanographenes as LIB anode; rate performance (charging-discharging); electrochromic technology; electrochromic materials; advantages of triphenylamine; requirement of electrochromic materials for practical applications; low driving voltage and long cycle life; increasing the electroactive sites by multi-step synthetic procedures; synthetic route to starburst triarylamine-based polyamide; electrochromism ranging from visible to NIR region; transmissive to black electrochromism; RGB and CMY electrochromism.

Nuclear materials

International Nuclear Information System (INIS)

1996-01-01

In 1998, Nuclear Regulatory Authority of the Slovak Republic (NRA SR) performed 38 inspections, 25 of them were performed in co-operation with IAEA inspectors. There is no fresh nuclear fuel at Bohunice A-1 NPP at present. Fresh fuel of Bohunice V-1 and V-2 NPPs is inspected in the fresh fuel storage.There are 327 fresh fuel assemblies in Mochovce NPP fresh fuel storage. In addition to that, are also 71 small users of nuclear materials in Slovakia. In most cases they use: covers made of depleted uranium for non-destructive works, detection of level in production plants, covers for therapeutical sources at medical facilities. In. 1995, NRA SR issued 4 new licences for nuclear material withdrawal. In the next part manipulation with nuclear materials, spent fuel stores and illegal trafficking in nuclear materials are reported

Carbon-covered Fe_3O_4 hollow cubic hierarchical porous composite as the anode material for lithium-ion batteries

International Nuclear Information System (INIS)

Chen, Shouhui; Zhou, Rihui; Chen, Yaqin; Fu, Yuanyuan; Li, Ping; Song, Yonghai; Wang, Li

2017-01-01

In this work, Prussian blue nanocrystals, a kind of cubic metal-organic frameworks, was firstly covered by a uniform layer of resorcinol-formaldehyde (RF) resin, and then followed with heat treatment at different pyrolysis temperatures. The effects of pyrolysis temperature on the morphologies, phase, pore size, and electrochemical performance of the pyrolysis products were studied in this work. The composite generated at 600 "∘C, FexC600, was a hollow cubic composite of Fe_3O_4 covered by a thin RF-derived carbon layer. The carbon layer on FexC600 was a robust and conductive protective layer, which can accommodate Fe_3O_4 NPs and withstand the huge volume change of Fe_3O_4 during the process of discharge and charge. When used as anodes for lithium-ion batteries, FexC600 showed excellent electrochemical performance. It delivered a discharge capacity of 1126 mAh g"−"1 with a coulombic efficiency of 98.8% at the current density of 100 mA g"−"1 after 100 times discharge/charge cycling. It even delivered a capacity of 492 mAh g"−"1 at the current density of 500 mA g"−"1. This cubic hollow composite would be a promising alternative anode material for lithium-ion batteries.

47{sup th} Annual meeting on nuclear technology (AMNT 2016). Key Topics / Enhanced safety and operation excellence

Energy Technology Data Exchange (ETDEWEB)

Bohnstedt, Angelika [Karlsruher Institut fuer Technologie (KIT), Eggenstein-Leopoldshafen (Germany). Programm Nukleare Entsorgung, Sicherheit und Strahlenforschung (NUSAFE); Baumann, Erik [AREVA GmbH, Erlangen (Germany). Radiation Protection

2016-12-15

Summary report on the Key Topic 'Enhanced Safety and Operation Excellence' Focus Session 'Radiation Protection' of the 47{sup th} Annual Meeting on Nuclear Technology (AMNT 2016) held in Hamburg, 10 to 12 May 2016. Other Sessions of AMNT 2016 have been and will be covered in further issues of atw.

Cover-gas seals: 11-LMFBR seal-test program

International Nuclear Information System (INIS)

Steele, O.P. III; Horton, P.H.

1977-01-01

The objective of the Cover Gas Seal Material Development Program is to perform the engineering development required to provide reliable seals for LMFBR application. Specific objectives are to verify the performance of commercial solid cross-section and inflatable seals under reactor environments including radiation, to develop advanced materials and configurations capable of achieving significant improvement in radioactive gas containment and seal temperature capabilities, and to optimize seal geometry for maximum reliability and minimal gas permeation

Nonlinear 3D calculations of turbine blade impact on turbine cover

International Nuclear Information System (INIS)

Hatala, B.; Adamik, V.; Buchar, J.

2000-01-01

This paper present the approach used at the VUJE institute for the evaluation of a ruptured blade impact on the current protection cover of a SKODA 220 MW turbine. Firstly, it briefly describes experiments (Hopkinson-Davies split bar facility, Taylor tests) and numerical simulations used to obtain realistic material parameters needed for the Cowper- Symonds material model that is implemented in the code LS-DYNA3D. Then, numerical simulations, by using the code, of the ruptured blade impact on various protection barriers are presented. These simulations make it possible to find an optimal solution for a new turbine protection cover. (author)

Book of abstracts of the joint EC-IAEA topical meeting on development of new structural materials for advanced fission and fusion reactor systems

International Nuclear Information System (INIS)

2009-01-01

, of the innovative materials concepts presently under consideration, and of system specific structural materials aspects will be given. The key topics of the meeting are the following: - Radiation damage phenomena and modelling of material properties under irradiation; - On-going challenges in radiation materials science; - Key material parameters and operational conditions of selected reactor designs; -Microstructures and mechanical properties of nuclear structural materials; - Pathways to development of new structural materials; - Qualification of new structural materials; - Advanced microstructural probing methods. Special emphasis is given to the application of nuclear techniques in the development and qualification of new structural materials. Each of the papers in this Book of Abstracts has been indexed separately

Radiation effects on structural materials

International Nuclear Information System (INIS)

Ghoniem, N.M.

1991-01-01

This report discusses the following topics on the effect radiation has on thermonuclear reactor materials: Atomic Displacements; Microstructure Evolution; Materials Engineering, Mechanics, and Design; Research on Low-Activation Steels; and Research Motivated by Grant Support

Tactile Models and Games as Learning Tools for Topics of Molecular and Cell Biology

OpenAIRE

Nelma Regina Segnini Bossolan

2017-01-01

The cell structure and the dynamics of its functioning are basic topics for the understanding of phenomena on a larger scale in living organisms and for which research in science teaching has suggested several strategies based on the use of images, games, computational simulations and tactile models, among other types of external representations. Our science education research group, over the last 17 years, has developed and evaluated educational materials for teaching these topics, aimed at ...

State-of-the-art review of materials properties of nuclear waste forms

International Nuclear Information System (INIS)

Mendel, J.E.; Nelson, R.D.; Turcotte, R.P.; Gray, W.J.; Merz, M.D.; Roberts, F.P.; Weber, W.J.; Westsik, J.H. Jr.; Clark, D.E.

1981-04-01

The Materials Characterization Center (MCC) was established at the Pacific Northwest Laboratory to assemble a standardized nuclear waste materials data base for use in research, systems and facility design, safety analyses, and waste management decisions. This centralized data base will be provided through the means of a Nuclear Waste Materials Handbook. The first issue of the Handbook will be published in the fall of 1981 in looseleaf format so that it can be updated as additional information becomes available. To ensure utmost reliability, all materials data appearing in the Handbook will be obtained by standard procedures defined in the Handbook and approved by an independent Materials Review Board (MRB) comprised of materials experts from Department of Energy laboratories and from universities and industry. In the interim before publication of the Handbook there is need for a report summarizing the existing materials data on nuclear waste forms. This review summarizes materials property data for the nuclear waste forms that are being developed for immobilization of high-level radioactive waste. It is intended to be a good representation of the knowledge concerning the properties of HLW forms as of March 1981. The table of contents lists the following topics: introduction which covers waste-form categories, and important waste-form materials properties; physical properties; mechanical properties; chemical durability; vaporization; radiation effects; and thermal phase stability

Magnetism and Structure in Functional Materials

CERN Document Server

Planes, Antoni; Saxena, Avadh

2005-01-01

Magnetism and Structure in Functional Materials addresses three distinct but related topics: (i) magnetoelastic materials such as magnetic martensites and magnetic shape memory alloys, (ii) the magnetocaloric effect related to magnetostructural transitions, and (iii) colossal magnetoresistance (CMR) and related magnanites. The goal is to identify common underlying principles in these classes of materials that are relevant for optimizing various functionalities. The emergence of apparently different magnetic/structural phenomena in disparate classes of materials clearly points to a need for common concepts in order to achieve a broader understanding of the interplay between magnetism and structure in this general class of new functional materials exhibiting ever more complex microstructure and function. The topic is interdisciplinary in nature and the contributors correspondingly include physicists, materials scientists and engineers. Likewise the book will appeal to scientists from all these areas.

Teaching about Climate Change and Energy with Online Materials and Workshops from On the Cutting Edge

Science.gov (United States)

Kirk, K. B.; Manduca, C. A.; Myers, J. D.; Loxsom, F.

2009-12-01

Global climate change and energy use are among the most relevant and pressing issues in today’s science curriculum, yet they are also complex topics to teach. The underlying science spans multiple disciplines and is quickly evolving. Moreover, a comprehensive treatment of climate change and energy use must also delve into perspectives not typically addressed in geosciences courses, such as public policy and economics. Thus, faculty attempting to address these timely issues face many challenges. To support faculty in teaching these subjects, the On the Cutting Edge faculty development program has created a series of websites and workshop opportunities to provide faculty with information and resources for teaching about climate and energy. A web-based collection of teaching materials was developed in conjunction with the On the Cutting Edge workshops “Teaching about Energy in Geoscience Courses: Current Research and Pedagogy.” The website is designed to provide faculty with examples, references and ideas for either incorporating energy topics into existing geoscience courses or for designing or refining a course about energy. The website contains a collection of over 30 classroom and lab activities contributed by faculty and covering such diverse topics as renewable energy, energy policy and energy conservation. Course descriptions and syllabi for energy courses address audiences ranging from introductory courses to advanced seminars. Other materials available on the website include a collection of visualizations and animations, a catalog of recommended books, presentations and related references from the teaching energy workshops, and ideas for novel approaches or new topics for teaching about energy in the geosciences. The Teaching Climate Change website hosts large collections of teaching materials spanning many different topics within climate change, climatology and meteorology. Classroom activities highlight diverse pedagogic approaches such as role

Modern methods of material accounting for mixed-oxide fuel-fabrication facility

International Nuclear Information System (INIS)

Eggers, R.F.; Brouns, R.J.; Brite, D.W.; Pindak, J.L.

1981-07-01

The generic requirements loss detection, and response to alarms of a contemporary material control and accounting (MC and A) philosophy have been applied to a mixed-oxide fuel-fabrication plant to produce a detailed preliminary MC and A system design that is generally applicable to facilities of this type. This paper summarizes and discusses detailed results of the mixed-oxide fuel-fabrication plant study. Topics covered in this paper include: mixed-oxide fuel-fabrication process description, process disaggregation into MC and A system control units, quantitative results of analysis of control units for abrupt and recurring loss-detection capability, impact of short- and long-term holdup on loss-detection capability, response to alarms for abrupt loss, and response to alarms for recurring loss

Usefulness of flexible covered stent in malignant colorectal obstruction

Energy Technology Data Exchange (ETDEWEB)

Kang, Jee Hee; Kang, Sung Gwon; Kim, Hyung Jin; Noh, Hong Gi; Woo, Jae Hong; Suh, Chang Hae [Inha Univ. Hospital, Inchon (Korea, Republic of)

1998-07-01

To evaluate the usefulness of flexible covered stent in the treatment of acute colorectal obstruction secondary to colorectal carcinoma. Materials and Methods : Flexible covered stents were placed in 11 patients with clinical and radiologic signs of acute colonic obstruction secondary to colorectal carcinoma. The purposes of stent insertion were pre-operative bowel preparation in seven patients and palliative treatment in four. A fistula was present in two;in one this was between the proximal jejunum and colon, and the other was rectovaginal. The usefulness of stent insertion for the purpose of preoperative bowel preparation was evaluated according to the feasibility and status of bowel preparation, as decided by the operator. Palliative treatment for the relief of symptoms of acute bowel obstruction was evaluated according to the number and amount of defecation,bowel dilatation in simple abdomen radiography, and the presence of complications. Results : Bowel preparation for the purpose of preoperative bowel cleansing was easy in seven patients;the fecal materials remaining in the colon presented no problems during surgery. In one of four patients palliative treatment involved a colostomy;this was due to recurrent stent obstruction by fecal materials after three months, and in two other patients there was stent obstruction after two and five months, respectively. The stent in one of four patients who underwent palliative treatment was removed because of stent migration three days after insertion;the stents in two patients with fistulas covered the fistulas successfully. Complications after stent insertion were anal pain in three patients, anal bleeding in three and stent migration in one. Conclusion : The flexible covered stent was an effective device for the relief of acute colonic obstruction secondary to malignant rectosigmoid neoplasia. It allowed for single-stage operation and covered the fistula. We believe however that for further evaluation of the

Proceedings of DAE-BRNS third international symposium on materials chemistry

International Nuclear Information System (INIS)

Tyagi, Deepak; Banerjee, Atindra Mohan; Nigam, Sandeep; Varma, Salil; Tripathi, Arvind Kumar; Bharadwaj, Shyamala Rajkumar; Das, Dasarathi

2010-12-01

The present volume consists of the proceedings of the DAE-BRNS Third International Symposium on Materials Chemistry. In order to keep pace with the advancements made in the area of materials chemistry, new topics like materials for energy conversion, biomaterials, carbon based materials, soft condensed materials, thin films, surface chemistry, polymer based materials, organic and organometallics, magnetic materials and high purity materials have been included in this symposium while topics like nuclear materials, nanomaterials and clusters, catalysis, chemical sensors, fuel cell materials and computational research in materials chemistry have been continued as important features of the symposium. Papers relevant to INIS are indexed separately

TOPICAL REVIEW: Metallo-supramolecular modules as a paradigm for materials science

Directory of Open Access Journals (Sweden)

Dirk G Kurth

2008-01-01

Full Text Available Metal ion coordination in discrete or extended metallo-supramolecular assemblies offers ample opportunity to fabricate and study devices and materials that are equally important for fundamental research and new technologies. Metal ions embedded in a specific ligand field offer diverse thermodynamic, kinetic, chemical, physical and structural properties that make these systems promising candidates for active components in functional materials. A key challenge is to improve and develop methodologies for placing these active modules in suitable device architectures, such as thin films or mesophases. This review highlights recent developments in extended, polymeric metallo-supramolecular systems and discrete polyoxometalates with an emphasis on materials science.

Topical issues in nuclear, radiation and radioactive waste safety. Contributed papers

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-08-01

The IAEA International Conference on Topical Issues in Nuclear, Radiation and Radioactive Waste Safety was held in Vienna, Austria, 30 August - 4 September 1998 with the objective to foster the exchange of information on topical issues in nuclear, radiation and radioactive waste safety, with the aim of consolidating an international consensus on: the present status of these issues; priorities for future work; and needs for strengthening international co-operation, including recommendations for the IAEA`s future activities. The document includes 43 papers presented at the Conference dealing with the following topical issues: Safety Management; Backfitting, Upgrading and Modernization of NPPs; Regulatory Strategies; Occupational Radiation Protection: Trends and Developments; Situations of Chronic Exposure to Residual Radioactive Materials: Decommissioning and Rehabilitation and Reclamation of Land; Radiation Safety in the Far Future: The Issue of Long Term Waste Disposal. A separate abstract and indexing were provided for each paper. Refs, figs, tabs

Topical issues in nuclear, radiation and radioactive waste safety. Contributed papers

International Nuclear Information System (INIS)

1998-08-01

The IAEA International Conference on Topical Issues in Nuclear, Radiation and Radioactive Waste Safety was held in Vienna, Austria, 30 August - 4 September 1998 with the objective to foster the exchange of information on topical issues in nuclear, radiation and radioactive waste safety, with the aim of consolidating an international consensus on: the present status of these issues; priorities for future work; and needs for strengthening international co-operation, including recommendations for the IAEA's future activities. The document includes 43 papers presented at the Conference dealing with the following topical issues: Safety Management; Backfitting, Upgrading and Modernization of NPPs; Regulatory Strategies; Occupational Radiation Protection: Trends and Developments; Situations of Chronic Exposure to Residual Radioactive Materials: Decommissioning and Rehabilitation and Reclamation of Land; Radiation Safety in the Far Future: The Issue of Long Term Waste Disposal. A separate abstract and indexing were provided for each paper

Machinability of advanced materials

CERN Document Server

Davim, J Paulo

2014-01-01

Machinability of Advanced Materials addresses the level of difficulty involved in machining a material, or multiple materials, with the appropriate tooling and cutting parameters.  A variety of factors determine a material's machinability, including tool life rate, cutting forces and power consumption, surface integrity, limiting rate of metal removal, and chip shape. These topics, among others, and multiple examples comprise this research resource for engineering students, academics, and practitioners.

Incorporating Topic Assignment Constraint and Topic Correlation Limitation into Clinical Goal Discovering for Clinical Pathway Mining

Directory of Open Access Journals (Sweden)

Xiao Xu

2017-01-01

Full Text Available Clinical pathways are widely used around the world for providing quality medical treatment and controlling healthcare cost. However, the expert-designed clinical pathways can hardly deal with the variances among hospitals and patients. It calls for more dynamic and adaptive process, which is derived from various clinical data. Topic-based clinical pathway mining is an effective approach to discover a concise process model. Through this approach, the latent topics found by latent Dirichlet allocation (LDA represent the clinical goals. And process mining methods are used to extract the temporal relations between these topics. However, the topic quality is usually not desirable due to the low performance of the LDA in clinical data. In this paper, we incorporate topic assignment constraint and topic correlation limitation into the LDA to enhance the ability of discovering high-quality topics. Two real-world datasets are used to evaluate the proposed method. The results show that the topics discovered by our method are with higher coherence, informativeness, and coverage than the original LDA. These quality topics are suitable to represent the clinical goals. Also, we illustrate that our method is effective in generating a comprehensive topic-based clinical pathway model.

Optical materials technology for energy efficiency and solar energy conversion 7

International Nuclear Information System (INIS)

Granqvist, C.G.; Lampert, C.M.

1989-01-01

This book covers the following topics: smart window coatings; Transparent infrared reflectors; Holographic concentrators and reflectors; Solar collecting devices; Solar absorber coatings; Optical properties and durability

International Commission on Nuclear Non-Proliferation and Disarmament - A possible international regime to cover radiological materials

International Nuclear Information System (INIS)

Hautecouverture, Benjamin

2009-10-01

Even if a 'dirty bomb' has never been used to date, the perception of the existence of a threat is shared by many. Four main types of radiological and nuclear terrorist attacks can be outlined: - acquisition and use of a nuclear weapon, - attacks and acts of sabotage against a nuclear reactor or another nuclear facility, - acquisition of fissile material for the elaboration of an Improvised Nuclear Device, - terrorist use of radiological materials for the elaboration of a Radiological Dispersal Device (RDD). This paper seeks to evaluate the probability for a terrorist group to acquire and make use of radiological materials in the objective of detonating a RDD, and the current international framework put into place to address such a threat. Is an international regime to cover radiological materials already in place? How comprehensive / integrated is it? Does a new and/or separate system need to be set up? Before 9/11, two events in particular served to illustrate the threat of a radiological or nuclear terrorist attack: Moscow in 1996, Argun in 1998. Since the 9/11 attacks, a few other radiological events have occurred, which could suggest that the threat is becoming more pressing. It must be noted that the use of a dirty bomb by a terrorist group would most probably be aimed at the contamination of a given geographical area, rather than mass destruction and killing. Indeed, the lethal impact of such weapons remains limited. For this reason, dirty bombs are considered by analysts as weapons of mass disruption rather than weapons of mass destruction. Impacts would be more important in the psychological or economic realms: - targeting highly populated environments, such as cities, would most probably not result in a high death toll; - compared with impacts on health, psychological impacts of such an attack would be much more serious, both within and outside the targeted population; - economic damage is probably the greatest threat posed by such attacks, particularly

Radiation materials science. V. 7

International Nuclear Information System (INIS)

Zelenskij, V.F.

1990-01-01

This volume includes the papers of the international conference on radiation materials in Alushta, Ukraine in May 1990. The main topics are: basic research in radiation damage physics, a study of the structural materials for reactor cores; irradiation effect on reactor vessel, fuel, super- and semiconductor materials; investigation damage research methods

Radiation materials science. V. 6

International Nuclear Information System (INIS)

Zelenskij, V.F.

1990-01-01

This volume includes the papers of the international conference on radiation materials in Alushta, Ukraine in May 1990. The main topics are: basic research in radiation damage physics, a study of the structural materials for reactor cores; irradiation effect on reactor vessel, fuel, super- and semiconductor materials; investigation damage research methods

Concrete cover cracking due to uniform reinforcement corrosion

DEFF Research Database (Denmark)

Solgaard, Anders Ole Stubbe; Michel, Alexander; Geiker, Mette Rica

2013-01-01

and reinforcement de-passivation is a frequently used limit state. The present paper investigates an alternative limit state: corrosion-induced cover cracking. Results from numerical simulations of concrete cover cracking due to reinforcement corrosion are presented. The potential additional service life...... is calculated using literature data on corrosion rate and Faraday’s law. The parameters varied comprise reinforcement diameter, concrete cover thickness and concrete material properties, viz. concrete tensile strength and ductility (plain concrete and fibre reinforced concrete). Results obtained from......Service life design (SLD) is an important tool for civil engineers to ensure that the structural integrity and functionality of the structure is not compromised within a given time frame, i.e. the service life. In SLD of reinforced concrete structures, reinforcement corrosion is of major concern...

Health Topic XML File Description

Science.gov (United States)

... this page: https://medlineplus.gov/xmldescription.html Health Topic XML File Description: MedlinePlus To use the sharing ... information categories assigned. Example of a Full Health Topic Record A record for a MedlinePlus health topic ...

Summary record of the topical session of 16. Meeting of the IGSC

International Nuclear Information System (INIS)

Van Luik, Abe; Smith, Paul

2014-01-01

The sixteenth meeting of the Integration Group for the Safety case (IGSC) included a topical session titled: Handling extreme geological events in safety cases during the post-closure phase. The session included nine presentations on the handling of such events by various national programs, questions and answers on each presentation and ended with a general discussion period. The present document summarises the outcome of the meeting. The document is structured as follows: - Section 2 describes the types of extreme geological events discussed in the session and how these are identified, - Section 3 discusses the measures that can be taken to avoid such events and to mitigate their impact on repositories, - Section 4 describes how the likelihood and consequences of events are assessed, - Section 5 address experiences regarding interactions with regulators and other stakeholders, - Section 6 covers remaining issues and planned R and D to address these, and - Section 7 presents a recommendation for possible future collaborative work on this topic

Medical support of children’s sports: Topical problems

Directory of Open Access Journals (Sweden)

L. A. Balykova

2017-01-01

Full Text Available The paper discusses the most topical issues of medical support of children and adolescents engaged in physical exercises and sports. Much attention is paid to different views on the etiology, pathogenesis, diagnosis, and principles of therapy of pathological transformation of the heart in child athletes. The problem of sudden cardiac death in sports and the possibility of a relationship between connective tissue dysplasia and its development are touched upon. Electrocardiographic and morphological criteria for cardiac maladaptation in athletes are discussed. The problem of early and accessible diagnosis and Russia’s tactics for the diagnosis of health changes in athletes and approaches to their prevention and treatment are covered. Different ways to prevent the pathological transformation of the cardiovascular system in athletes and sudden cardiac death as its extreme manifestation are discussed.

The safe transport of radioactive materials

CERN Document Server

Gibson, R

1966-01-01

The Safe Transport of Radioactive Materials is a handbook that details the safety guidelines in transporting radioactive materials. The title covers the various regulations and policies, along with the safety measures and procedures of radioactive material transport. The text first details the 1963 version of the IAEA regulation for the safe transport of radioactive materials; the regulation covers the classification of radionuclides for transport purposes and the control of external radiation hazards during the transport of radioactive materials. The next chapter deals with concerns in the im

Cover-layer with High Refractive Index for Near-Field Recording Media

Science.gov (United States)

Kim, Jin-Hong; Lee, Jun-Seok

2007-06-01

TiO2 nanoparticles are added into UV-curable resin to increase the refractive index of the cover-layer laminated for cover-layer incident near-field recording media. A high refractive index is required for the cover-layer operating with an optical head with a high numerical aperture. The eye pattern from a cover-layer coated 20 GB read-only memory disc in which the refractive index of the cover-layer is 1.75 is achieved, but the gap servo is unstable owing to the rough surface of the cover-layer. Even though the light loss due to the nanoparticles is negligible, a rough microstructure is developed by adding the nanoparticles into an organic binder material. To achieve a smooth surface for a stable gap servo, the solubility of the nanoparticles should be enhanced by the optimization of the surface of the nanoparticles.

Advanced topics on rotor blade full-scale structural fatigue testing and requirements

DEFF Research Database (Denmark)

Berring, Peter; Fedorov, Vladimir; Belloni, Federico

further developed since then. Structures in composite materials are generally difficult and time consuming to test for fatigue resistance. Therefore, several methods for testing of blades have been developed and exist today. Those methods are presented in [1]. This report deals with more advanced topics...

Land Cover - Minnesota Land Cover Classification System

Data.gov (United States)

Minnesota Department of Natural Resources — Land cover data set based on the Minnesota Land Cover Classification System (MLCCS) coding scheme. This data was produced using a combination of aerial photograph...

International Conference on the Safe and Secure Transport of Radioactive Material: The Next Fifty Years of Transport - Creating a Safe, Secure and Sustainable Framework. Papers and Presentations

International Nuclear Information System (INIS)

2011-01-01

The objective of the conference is to encourage application of appropriate levels of safety and security during transport by: Promoting international discussion on the safety and security of radioactive material transport; Identifying and sharing best practices; Identifying issues and problems; Identifying opportunities, such as providing assistance, to support national adoption of comprehensive transport safety and security frameworks; Developing ideas for coordinating and enhancing transport safety and security. Scope of the Conference: Nuclear and other radioactive material in legal regulated transport (not illicit trafficking, smuggling, etc.); All modes of transport; Safety; Security; Domestic and international movements, including transit; Response to accidents and security events; Legislative and regulatory requirements and approaches; Practical issues such as transport logistics; Regional networks; and Information security and the need for transparency. The conference is not intended to cover the technical topics covered in the PATRAM conference (package design and analysis).

Developing Instructional Materials for Business Japanese.

Science.gov (United States)

Koike, Shohei

Business Japanese should be the study of Japanese language and culture for business communication and should include values and beliefs and institutional constraints on which the Japanese act as well as business etiquette and terminology. Topics to be covered in instruction will vary depending on the role (seller, buyer, or colleague) played by…

NATO Advanced Study Institute on Nondestructive Evaluation of Semiconductor Materials and Devices

CERN Document Server

1979-01-01

From September 19-29, a NATO Advanced Study Institute on Non­ destructive Evaluation of Semiconductor Materials and Devices was held at the Villa Tuscolano in Frascati, Italy. A total of 80 attendees and lecturers participated in the program which covered many of the important topics in this field. The subject matter was divided to emphasize the following different types of problems: electrical measurements; acoustic measurements; scanning techniques; optical methods; backscatter methods; x-ray observations; accele­ rated life tests. It would be difficult to give a full discussion of such an Institute without going through the major points of each speaker. Clearly this is the proper task of the eventual readers of these Proceedings. Instead, it would be preferable to stress some general issues. What came through very clearly is that the measurements of the basic scientists in materials and device phenomena are of sub­ stantial immediate concern to the device technologies and end users.

Use of superabsorbent polymers in construction materials

DEFF Research Database (Denmark)

Jensen, Ole Mejlhede

2008-01-01

extreme and reversible water absorption, porosity formation, water blocking and controlled release of substances. The overview does not cover all aspects of SAP use, but is focused on topics the author has been dealing with. In particular examples of SAP use within concrete construction are elaborated....

The human heart and the circulatory system as an interesting interdisciplinary topic in lessons of physics and biology

International Nuclear Information System (INIS)

Volná, M; Látal, F; Kubínek, R; Richterek, L

2014-01-01

Many topics which are closely related can be found in the national curriculum of the Czech Republic for physics and biology. One of them is the heart and the circulatory system in the human body. This topic was examined cross curriculum, a teaching module was created and the topic was chosen for our research. The task was to determine if the students of bachelor study are aware of connections between physics and biology within this topic and whether we can help them effectively to describe the corresponding physics phenomena in the human body connected, for example, with a heart attack or with the measurement of blood pressure. In this paper, the heart and the circulatory system are presented as suitable topics for an interdisciplinary teaching module which includes both theoretical and experimental parts. The module was evaluated by a group of first-year undergraduate students of physics at the Faculty of Science, Palacký University. The acquired knowledge was compared with another control group through a test. The highest efficiency of the module was evaluated on the basis of questions that covered the calculation problems. (paper)

Identifying Topics in Microblogs Using Wikipedia.

Science.gov (United States)

Yıldırım, Ahmet; Üsküdarlı, Suzan; Özgür, Arzucan

2016-01-01

Twitter is an extremely high volume platform for user generated contributions regarding any topic. The wealth of content created at real-time in massive quantities calls for automated approaches to identify the topics of the contributions. Such topics can be utilized in numerous ways, such as public opinion mining, marketing, entertainment, and disaster management. Towards this end, approaches to relate single or partial posts to knowledge base items have been proposed. However, in microblogging systems like Twitter, topics emerge from the culmination of a large number of contributions. Therefore, identifying topics based on collections of posts, where individual posts contribute to some aspect of the greater topic is necessary. Models, such as Latent Dirichlet Allocation (LDA), propose algorithms for relating collections of posts to sets of keywords that represent underlying topics. In these approaches, figuring out what the specific topic(s) the keyword sets represent remains as a separate task. Another issue in topic detection is the scope, which is often limited to specific domain, such as health. This work proposes an approach for identifying domain-independent specific topics related to sets of posts. In this approach, individual posts are processed and then aggregated to identify key tokens, which are then mapped to specific topics. Wikipedia article titles are selected to represent topics, since they are up to date, user-generated, sophisticated articles that span topics of human interest. This paper describes the proposed approach, a prototype implementation, and a case study based on data gathered during the heavily contributed periods corresponding to the four US election debates in 2012. The manually evaluated results (0.96 precision) and other observations from the study are discussed in detail.

Book of abstracts of the Fifth International School for young scientists and specialists Interaction of hydrogen isotopes with structural materials. IHISM-09 JUNIOR

International Nuclear Information System (INIS)

2009-01-01

The book includes abstracts of presentations at the Fifth International School for young scientists and specialists Interaction of hydrogen isotopes with structural materials (IHISM-09 JUNIOR). Abstracts of lecture faculty and reports of young scientists and specialists covering the use of hydrogen isotopes in energetics, national economy and fundamental researches are given. Papers presented on the following topics: mechanical properties and structural transformations; kinetics and thermodynamics of interaction between hydrogen isotopes and solids including effects of radiogenic helium accumulation, hydrides and hydride transformations; equipment and research techniques

Aerospace materials and material technologies

CERN Document Server

Wanhill, R

2017-01-01

This book is a comprehensive compilation of chapters on materials (both established and evolving) and material technologies that are important for aerospace systems. It considers aerospace materials in three Parts. Part I covers Metallic Materials (Mg, Al, Al-Li, Ti, aero steels, Ni, intermetallics, bronzes and Nb alloys); Part II deals with Composites (GLARE, PMCs, CMCs and Carbon based CMCs); and Part III considers Special Materials. This compilation has ensured that no important aerospace material system is ignored. Emphasis is laid in each chapter on the underlying scientific principles as well as basic and fundamental mechanisms leading to processing, characterization, property evaluation and applications. A considerable amount of materials data is compiled and presented in appendices at the end of the book. This book will be useful to students, researchers and professionals working in the domain of aerospace materials.

Recent Topical Research on Global, Energy, Health & Medical, and Tourism Economics, and Global Software

OpenAIRE

Chang, Chia-Lin; McAleer, Michael

2017-01-01

textabstractThe paper presents an overview of recent topical research on global, energy, health & medical, and tourism economics, and global software. We have interpreted “global” in the title of the Journal of Reviews on Global Economics to cover contributions that have a global impact on economics, thereby making it “global economics”. In this sense, the paper is concerned with papers on global, energy, health & medical, and tourism economics, as well as global software algorithms that have...

Advances in the material science of concrete

National Research Council Canada - National Science Library

Ideker, Jason H; Radlinska, Aleksandra

2010-01-01

... Committee 236, Material Science of Concrete. The session focused on material science aspects of concrete with an emphasis placed on advances in understanding the fundamental scientific topics of cement-based materials, as well as the crucial...

Surface physics of materials materials science and technology

CERN Document Server

Blakely, J M

2013-01-01

Surface Physics of Materials presents accounts of the physical properties of solid surfaces. The book contains selected articles that deal with research emphasizing surface properties rather than experimental techniques in the field of surface physics. Topics discussed include transport of matter at surfaces; interaction of atoms and molecules with surfaces; chemical analysis of surfaces; and adhesion and friction. Research workers, teachers and graduate students in surface physics, and materials scientist will find the book highly useful.

Eulerian Graphs and Related Topics

CERN Document Server

Fleischner, Herbert

1990-01-01

The two volumes comprising Part 1 of this work embrace the theme of Eulerian trails and covering walks. They should appeal both to researchers and students, as they contain enough material for an undergraduate or graduate graph theory course which emphasizes Eulerian graphs, and thus can be read by any mathematician not yet familiar with graph theory. But they are also of interest to researchers in graph theory because they contain many recent results, some of which are only partial solutions to more general problems. A number of conjectures have been included as well. Various problems (such a

Regulatory Information By Topic

Science.gov (United States)

EPA develops and enforces regulations that span many environmental topics, from acid rain reduction to wetlands restoration. Each topic listed below may include related laws and regulations, compliance enforcement information, policies guidance

Identifying Topics in Microblogs Using Wikipedia.

Directory of Open Access Journals (Sweden)

Ahmet Yıldırım

Full Text Available Twitter is an extremely high volume platform for user generated contributions regarding any topic. The wealth of content created at real-time in massive quantities calls for automated approaches to identify the topics of the contributions. Such topics can be utilized in numerous ways, such as public opinion mining, marketing, entertainment, and disaster management. Towards this end, approaches to relate single or partial posts to knowledge base items have been proposed. However, in microblogging systems like Twitter, topics emerge from the culmination of a large number of contributions. Therefore, identifying topics based on collections of posts, where individual posts contribute to some aspect of the greater topic is necessary. Models, such as Latent Dirichlet Allocation (LDA, propose algorithms for relating collections of posts to sets of keywords that represent underlying topics. In these approaches, figuring out what the specific topic(s the keyword sets represent remains as a separate task. Another issue in topic detection is the scope, which is often limited to specific domain, such as health. This work proposes an approach for identifying domain-independent specific topics related to sets of posts. In this approach, individual posts are processed and then aggregated to identify key tokens, which are then mapped to specific topics. Wikipedia article titles are selected to represent topics, since they are up to date, user-generated, sophisticated articles that span topics of human interest. This paper describes the proposed approach, a prototype implementation, and a case study based on data gathered during the heavily contributed periods corresponding to the four US election debates in 2012. The manually evaluated results (0.96 precision and other observations from the study are discussed in detail.

Symposium on international safeguards: Verification and nuclear material security. Book of extended synopses

International Nuclear Information System (INIS)

2001-01-01

The symposium covered the topics related to international safeguards, verification and nuclear materials security, namely: verification and nuclear material security; the NPT regime: progress and promises; the Additional Protocol as an important tool for the strengthening of the safeguards system; the nuclear threat and the nuclear threat initiative. Eighteen sessions dealt with the following subjects: the evolution of IAEA safeguards (including strengthened safeguards, present and future challenges; verification of correctness and completeness of initial declarations; implementation of the Additional Protocol, progress and experience; security of material; nuclear disarmament and ongoing monitoring and verification in Iraq; evolution of IAEA verification in relation to nuclear disarmament); integrated safeguards; physical protection and illicit trafficking; destructive analysis for safeguards; the additional protocol; innovative safeguards approaches; IAEA verification and nuclear disarmament; environmental sampling; safeguards experience; safeguards equipment; panel discussion on development of state systems of accountancy and control; information analysis in the strengthened safeguard system; satellite imagery and remote monitoring; emerging IAEA safeguards issues; verification technology for nuclear disarmament; the IAEA and the future of nuclear verification and security

A materials engineering view of license renewal at the US Nuclear Regulatory Commission

International Nuclear Information System (INIS)

Banic, M.

1999-01-01

This paper discusses the treatment of license renewal at the US Nuclear Regulatory Commission (NRC) with emphasis on the review process by the staff of the Materials and Chemical Engineering Branch (EMCB). The paper covers the rules governing license renewal, the applications received, the schedule, the approach, and the technical issues. The NRC has a tight schedule of 30-36 months to renew a license. To date, Baltimore Gas and Electric (BG and E) and Duke Power have applied for license renewal. Expecting more applicants, the staff has taken steps to address the public's concern that the effects of aging will be adequately managed and the industry's concern that the reviews will be timely, efficient, and uniform. These steps include identifying aging effects and making the results available in a report and computerized database, approving topical reports and aging management programs for generic use, and reviewing aging management programs according to specific criteria. Materials Engineering staff have a major role because many of the aging issues are materials related. (author)

Symposium on international safeguards: Verification and nuclear material security. Book of extended synopses

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

The symposium covered the topics related to international safeguards, verification and nuclear materials security, namely: verification and nuclear material security; the NPT regime: progress and promises; the Additional Protocol as an important tool for the strengthening of the safeguards system; the nuclear threat and the nuclear threat initiative. Eighteen sessions dealt with the following subjects: the evolution of IAEA safeguards (including strengthened safeguards, present and future challenges; verification of correctness and completeness of initial declarations; implementation of the Additional Protocol, progress and experience; security of material; nuclear disarmament and ongoing monitoring and verification in Iraq; evolution of IAEA verification in relation to nuclear disarmament); integrated safeguards; physical protection and illicit trafficking; destructive analysis for safeguards; the additional protocol; innovative safeguards approaches; IAEA verification and nuclear disarmament; environmental sampling; safeguards experience; safeguards equipment; panel discussion on development of state systems of accountancy and control; information analysis in the strengthened safeguard system; satellite imagery and remote monitoring; emerging IAEA safeguards issues; verification technology for nuclear disarmament; the IAEA and the future of nuclear verification and security.

IDENTIFICATION OF LAND COVER IN THE PAST USING INFRARED IMAGES AT PRESENT

Directory of Open Access Journals (Sweden)

V. Šafář

2012-07-01

Full Text Available Czech landscape is an old residential area used by humans since ancient times. People have influenced it since their arrival and various activities in different periods create landscape layers called a palimpsest. Land Cover of one location could have changed several times. The most important reason is meandering and subsequent straightening of rivers, deforestation, relocation and change in soil layers. These changes in the past affected the present management and it is important to identify them. A suitable tool for the determination of different sites is remote sensing in the infrared spectrum, which monitors changes in the vegetation with the support of archival materials. After identifying the different places you can search the archival materials, how the land cover looked in the past. There have been used these archival materials: maps II. and III. military mapping, basic maps and other maps and historical orthophotomap. Czech Republic has a national archive of aerial photographs with aerial photographs from the thirties of the last century maintained by MGHO Dobruska. A comparative analysis of Land Cover shows the increases and decreases in agricultural land, changes in communication line elements, forest losses and increases, comparing the legal and actual status of the forest boundaries and their changes over time, changes in the built areas and links to the surrounding countryside. Land Cover of this study was created primarily with a visual interpretation of each area with their vectorization and assigning attributes to these areas and then comparing each of archival materials.

Multidimensional simulation of radon diffusion through earthen covers

International Nuclear Information System (INIS)

Mayer, D.W.; Gee, G.W.

1983-01-01

The purpose of this report is to document applications of the RADMD model used at PNL to perform analyses of radon diffusion through uranium mill tailings cover systems. The accuracy of the numerical formulation of the RADMD model was demonstrated through a comparison with a two-dimensional analytic solution to the radon diffusion equation. Excellent agreement was obtained between two-dimensional radon concentration profiles predicted by RADMD and those obtained with the analytic solution. A simulation was made of radon diffusion into a test canister using the two dimensional capabilities of RADMD. The radon flux profile was computed and illustrates the effects of the canister on the surface radon flux. The influence of the canister on the radon flux was shown to be significant under certain circumstances. Defects in earthen cover systems were evaluated using the three dimensional capabilities of RADMD. The results support the expectation that defective covers can increase the surface flux from a covered talings pile. Compared to a cover with no defects, radon flux could be elevated by as much as a factor of three when 20% of the radon control layer area contained pockets of reduced moisture. The effects of temporal and spatial variations in moisture content have been modeled by coupling RADMD with a variable saturated flow model. Two dimensional simulations were made of the time dependence of radon flux from a tailings site before and after cover placement. The results demonstrated the expected flux reduction produced by a thick earthen cover. Time dependence of the radon flux after cover placement was attributed to slight changes in moisture content of the cover material with time. The particular cover studied had a compacted clay layer that effectively attenuated the radon

Transfer of toxic and radioactive materials to and from a work enclosure

International Nuclear Information System (INIS)

Hackney, S.

1980-01-01

Apparatus for transfer of toxic and radioactive materials between a work enclosure, e.g. a glove box, and a container for storing and transporting the materials comprises a 'double-cover' through which materials are moved. A port in the enclosure is closed by a first cover and the container is closed by a second cover. During transfer, the covers are connected together and the space between the covers is swept by an air stream supplied by a pipe to prevent ingress and deposition of toxic or radioactive material on the facing surfaces of the cover which are subsequently exposed to the environment on separation of the covers. (author)

Mobility of as, Cu, Cr, and Zn from tailings covered with sealing materials using alkaline industrial residues: a comparison between two leaching methods.

Science.gov (United States)

Jia, Yu; Maurice, Christian; Öhlander, Björn

2016-01-01

Different alkaline residue materials (fly ash, green liquor dregs, and lime mud) generated from the pulp and paper industry as sealing materials were evaluated to cover aged mine waste tailings (tailings in the batch system only As dramatically exceeded the limit values at L/S 10 L/kg. The leaching results showed similar patterns to the batch results, though leached Cr, Cu, and Zn showed higher levels in the column tests than in the batch tests. However, when the columns were compared with the batches, the trend for Cu was opposite for the unamended tailings. By contrast, both batch and column results showed that the amendment caused mobilization of As compared with the unamended tailings in the ash-amended tailings. The amount of As released was greatest in the ash column and decreased from the dregs to the lime columns. The leaching of As at high levels can be a potential problem whenever alkaline materials (especially for fly ash) are used as sealing materials over tailings. The column test was considered by the authors to be a more informative method in remediation of the aged tailings with low sulfur content, since it mimics better actual situation in a field.

Topical therapy for facial allergic dermatoses

Directory of Open Access Journals (Sweden)

Y. S. Kondratyeva

2015-01-01

Full Text Available The research goal is to assess clinical dynamics and morphofunctional skin parameters of patients with facial allergic dermatoses on the background of combined topical therapy. Materials and methods. 45 patients with various facial allergic dermatoses in dry and sensitive skin took part in the research. The methods included anamnesis taking, poll, objective examination and assessment of morphofunctional parameters of skin, as well as estimation of life quality dynamic index (LQDI. Main results. After a course of treatment with 0,05% solution of alclometasone dipropionate inflammation of dermatosis ceased in 45 (100% patients, itching and pains in 39 (86,7% patients, but complaints about dryness and peeling of facial skin remained in 41 (91,1% and 40 (88,8% patients respectively. On the background of therapy including emollient Aflocream the above mentioned symptoms did not appear in 43 (95,6% patients, wherein maximum effect was achieved in patients with allergic contact dermatitis - 14 (93,3%. After a course of topical therapy all patients showed statistically significant increase of epidermal moisture level, alongside with reduction of skin relief and degree of keratinization. During the assessment of LQDI a tendency to reduction of proportion of patients on whom the disease has a strong and extremely strong impact was noted in 10 patients (i.e. 22,2%, moderate influence - in 5 of them (11,45%, insignificant influence or its absence - in 30 (66,7% people. Conclusion. Combined therapy including the use of a topical corticosteroid Afloderm and an emollient Aflocream showed good clinical efficiency in patients with facial allergic dermatoses. The efficiency is also confirmed with improvements in morphofunctional characteristics of patients’ skin on the background of therapy.

Magnetic Materials

Science.gov (United States)

Spaldin, Nicola A.

2003-04-01

Magnetic materials are the foundation of multi-billion dollar industries and the focus of intensive research across many disciplines. This book covers the fundamentals, basic theories and applications of magnetism and conventional magnetic materials. Based on a lecture course given by Nicola Spaldin in the Materials Department at University of California, Santa Barbara, the book is ideal for a one- semester course in magnetic materials. It contains numerous homework problems and solutions.

Differential Topic Models.

Science.gov (United States)

Chen, Changyou; Buntine, Wray; Ding, Nan; Xie, Lexing; Du, Lan

2015-02-01

In applications we may want to compare different document collections: they could have shared content but also different and unique aspects in particular collections. This task has been called comparative text mining or cross-collection modeling. We present a differential topic model for this application that models both topic differences and similarities. For this we use hierarchical Bayesian nonparametric models. Moreover, we found it was important to properly model power-law phenomena in topic-word distributions and thus we used the full Pitman-Yor process rather than just a Dirichlet process. Furthermore, we propose the transformed Pitman-Yor process (TPYP) to incorporate prior knowledge such as vocabulary variations in different collections into the model. To deal with the non-conjugate issue between model prior and likelihood in the TPYP, we thus propose an efficient sampling algorithm using a data augmentation technique based on the multinomial theorem. Experimental results show the model discovers interesting aspects of different collections. We also show the proposed MCMC based algorithm achieves a dramatically reduced test perplexity compared to some existing topic models. Finally, we show our model outperforms the state-of-the-art for document classification/ideology prediction on a number of text collections.

Topic Model for Graph Mining.

Science.gov (United States)

Xuan, Junyu; Lu, Jie; Zhang, Guangquan; Luo, Xiangfeng

2015-12-01

Graph mining has been a popular research area because of its numerous application scenarios. Many unstructured and structured data can be represented as graphs, such as, documents, chemical molecular structures, and images. However, an issue in relation to current research on graphs is that they cannot adequately discover the topics hidden in graph-structured data which can be beneficial for both the unsupervised learning and supervised learning of the graphs. Although topic models have proved to be very successful in discovering latent topics, the standard topic models cannot be directly applied to graph-structured data due to the "bag-of-word" assumption. In this paper, an innovative graph topic model (GTM) is proposed to address this issue, which uses Bernoulli distributions to model the edges between nodes in a graph. It can, therefore, make the edges in a graph contribute to latent topic discovery and further improve the accuracy of the supervised and unsupervised learning of graphs. The experimental results on two different types of graph datasets show that the proposed GTM outperforms the latent Dirichlet allocation on classification by using the unveiled topics of these two models to represent graphs.

CONFERENCE NOTE: European Optical Society, Topical Meeting Optical Metrology and Nanotechnology, Engelberg, Switzerland, 27 30 March 1994

Science.gov (United States)

1993-01-01

This meeting, organized by the Paul Scherrer Institute's Department of Applied Solid State Physics, will be held from 27 30 March 1994 at the Hotel Regina-Titlis, Engelberg, Switzerland. The aim is to bring together scientists from two important fields of current research and increasing industrial relevance. Optical metrology is a traditional discipline of applied optics which reached the nanometre scale a long time ago. Nanotechnology is setting new limits and represents a major challenge to metrology, as well as offering new opportunities to optics. The meeting is intended to help define a common future for optical metrology and nanotechnology. Topics to be covered include: nanometre position control and measuring techniques ultrahigh precision interferometry scanning probe microscopy (AFM, SNOM, etc.) surface modification by scanning probe methods precision surface fabrication and characterization nanolithography micro-optics, diffractive optics components, including systems and applications subwavelength optical structures synthetic optical materials structures and technologies for X-ray optics. For further information please contact: Jens Gobrecht (Secretary), Paul Scherrer Institute, CH-5232 Villigen-PSI, Switzerland.Tel. (41)56992529; Fax (41) 5698 2635.

Heterogeneous Materials I and Heterogeneous Materials II

International Nuclear Information System (INIS)

Knowles, K M

2004-01-01

In these two volumes the author provides a comprehensive survey of the various mathematically-based models used in the research literature to predict the mechanical, thermal and electrical properties of hetereogeneous materials, i.e., materials containing two or more phases such as fibre-reinforced polymers, cast iron and porous ceramic kiln furniture. Volume I covers linear properties such as linear dielectric constant, effective electrical conductivity and elastic moduli, while Volume II covers nonlinear properties, fracture and atomistic and multiscale modelling. Where appropriate, particular attention is paid to the use of fractal geometry and percolation theory in describing the structure and properties of these materials. The books are advanced level texts reflecting the research interests of the author which will be of significant interest to research scientists working at the forefront of the areas covered by the books. Others working more generally in the field of materials science interested in comparing predictions of properties with experimental results may well find the mathematical level quite daunting initially, as it is apparent that the author assumes a level of mathematics consistent with that taught in final year undergraduate and graduate theoretical physics courses. However, for such readers it is well worth persevering because of the in-depth coverage to which the various models are subjected, and also because of the extensive reference lists at the back of both volumes which direct readers to the various source references in the scientific literature. Thus, for the wider materials science scientific community the two volumes will be a valuable library resource. While I would have liked to see more comparison with experimental data on both ideal and 'real' heterogeneous materials than is provided by the author and a discussion of how to model strong nonlinear current--voltage behaviour in systems such as zinc oxide varistors, my overall

Encapsulation of cosmetic active ingredients for topical application--a review.

Science.gov (United States)

Casanova, Francisca; Santos, Lúcia

2016-02-01

Microencapsulation is finding increasing applications in cosmetics and personal care markets. This article provides an overall discussion on encapsulation of cosmetically active ingredients and encapsulation techniques for cosmetic and personal care products for topical applications. Some of the challenges are identified and critical aspects and future perspectives are addressed. Many cosmetics and personal care products contain biologically active substances that require encapsulation for increased stability of the active materials. The topical and transdermal delivery of active cosmetic ingredients requires effective, controlled and safe means of reaching the target site within the skin. Preservation of the active ingredients is also essential during formulation, storage and application of the final cosmetic product. Microencapsulation offers an ideal and unique carrier system for cosmetic active ingredients, as it has the potential to respond to all these requirements. The encapsulated agent can be released by several mechanisms, such as mechanical action, heat, diffusion, pH, biodegradation and dissolution. The selection of the encapsulation technique and shell material depends on the final application of the product, considering physical and chemical stability, concentration, required particle size, release mechanism and manufacturing costs.

Analyses of Research Topics in the Field of Informetrics Based on the Method of Topic Modeling

OpenAIRE

Sung-Chien Lin

2014-01-01

In this study, we used the approach of topic modeling to uncover the possible structure of research topics in the field of Informetrics, to explore the distribution of the topics over years, and to compare the core journals. In order to infer the structure of the topics in the field, the data of the papers published in the Journal of Informetricsand Scientometrics during 2007 to 2013 are retrieved from the database of the Web of Science as input of the approach of topic modeling. The results ...

Thermal behavior of laboratory models of honeycomb-covered solar ponds

Science.gov (United States)

Lin, E. I. H.

1983-01-01

Laboratory experiments were conducted to provide insight into the technical feasibility of honeycomb-covered solar ponds. Cooling tests using honeycomb panels of various materials and geometries showed that a 5.7-cm-thick one-tier panel insulated as effectively as a 10-cm fiberglass slab. Heating tests demonstrated that a model pond covered with a polycarbonate panel boiled upon 16 hours of continuous exposure to a 150-W spotlight. Analysis of the experimental data indicates positively that honeycomb-covered solar ponds can be expected to perform satisfactorily, and that larger-scale outdoor tests should be conducted to provide a more realistic assessment and a more refined performance estimate.

Photorefractive Materials and Their Applications 2 Materials

CERN Document Server

Günter, Peter

2007-01-01

Photorefractive Materials and Their Applications 2: Materials is the second of three volumes within the Springer Series in Optical Sciences. The book gives a comprehensive review of the most important photorefractive materials and discusses the physical properties of organic and inorganic crystals as well as poled polymers. In this volume, photorefractive effects have been investigated at wavelengths covering the UV, visible and near infrared. Researchers in the field and graduate students of solid-state physics and engineering will gain a thorough understanding of the properties of materials in photorefractive applications. The other two volumes are: Photorefractive Materials and Their Applications 1: Basic Effects. Photorefractive Materials and Their Applications 3: Applications.

Analyses of Research Topics in the Field of Informetrics Based on the Method of Topic Modeling

Directory of Open Access Journals (Sweden)

Sung-Chien Lin

2014-07-01

Full Text Available In this study, we used the approach of topic modeling to uncover the possible structure of research topics in the field of Informetrics, to explore the distribution of the topics over years, and to compare the core journals. In order to infer the structure of the topics in the field, the data of the papers published in the Journal of Informetricsand Scientometrics during 2007 to 2013 are retrieved from the database of the Web of Science as input of the approach of topic modeling. The results of this study show that when the number of topics was set to 10, the topic model has the smallest perplexity. Although data scopes and analysis methodsare different to previous studies, the generating topics of this study are consistent with those results produced by analyses of experts. Empirical case studies and measurements of bibliometric indicators were concerned important in every year during the whole analytic period, and the field was increasing stability. Both the two core journals broadly paid more attention to all of the topics in the field of Informetrics. The Journal of Informetricsput particular emphasis on construction and applications ofbibliometric indicators and Scientometrics focused on the evaluation and the factors of productivity of countries, institutions, domains, and journals.

Topical treatments of skin pain: a general review with a focus on hidradenitis suppurativa with topical agents.

Science.gov (United States)

Scheinfeld, Noah

2014-07-15

Hidradenitis Supprurativa (HS) is a painful chronic follicular disease. Few papers have addressed pain control for this debilitating condition. Possible topical agents include tricyclic antidepressants, opioids, anticonvulsants, NSAIDs, NMDA receptor antagonists, local anesthetics and other agents. The first line agents for the topical treatment of the cutaneous pain of HS are diclonefac gel 1% and liposomal xylocaine 4% and 5% cream or 5% ointment. The chief advantage of topical xylocaine is that is quick acting i.e. immediate however with a limited duration of effect 1-2 hours. The use of topical ketamine, which blocks n-methyl-D-aspartate receptors in a non-competitive fashion, might be a useful tool for the treatment of HS pain. Topical doxepin, which available in a 5% commercially preparation (Zonalon®) , makes patients drowsy and is not useful for controlling the pain of HS . Doxepin is available in a 3% or 3.3% concentration (which causes less drowsiness) from compounding pharmacies and can be used in compounded analgesic preparations with positive effect. Topical doxepin is preferred over use of topical amitriptyline because topical doxepin is more effective. Nevertheless, topical amitriptyline increase of the tactile and mechanical nociceptive thresholds and can be used for topical pain control in compound mixture of analgesics . Gabapentin and pregablin can also be used compounded with other agents in topical analgesic preparations with positive topical anesthetic effect. Capsaicin is not useful for topical treatment of the pain of HS. Sometimes compounded of anesthetics medications such as ketamine 10%, bupivacaine 1%, diclofenac 3%, doxepin 3% or 3.3%, and gabapentin 6% can extend the duration of effect so that medication only needs to be used 2 or 3 times a day. Still in my experience the easiest to get and most patient requested agent is topical diclonefac 1% gel.

Ultrafast control and monitoring of material properties using terahertz pulses

Energy Technology Data Exchange (ETDEWEB)

Bowlan, Pamela Renee [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Lab. for Ultrafast Materials Optical Science (LUMOS)

2016-05-02

These are a set of slides on ultrafast control and monitoring of material properties using terahertz pulses. A few of the topics covered in these slides are: How fast is a femtosecond (fs), Different frequencies probe different properties of molecules or solids, What can a THz pulse do to a material, Ultrafast spectroscopy, Generating and measuring ultrashort THz pulses, Tracking ultrafast spin dynamics in antiferromagnets through spin wave resonances, Coherent two-dimensional THz spectroscopy, and Probing vibrational dynamics at a surface. Conclusions are: Coherent two-dimensional THz spectroscopy: a powerful approach for studying coherence and dynamics of low energy resonances. Applying this to graphene we investigated the very strong THz light mater interaction which dominates over scattering. Useful for studying coupled excitations in multiferroics and monitoring chemical reactions. Also, THz-pump, SHG-probe spectoscopy: an ultrafast, surface sensitive probe of atomic-scale symmetry changes and nonlinear phonon dymanics. We are using this in Bi₂Se₃ to investigate the nonlinear surface phonon dynamics. This is potentially very useful for studying catalysis.

Technical specification for fabrication of HANARO pool cover

Energy Technology Data Exchange (ETDEWEB)

Ryu, Jeong Soo; Woo, Sang Ik

2001-06-01

This technical specification details the requirements and the acceptance criteria for design, seismic analysis, function test, installation and quality assurance for HANARO pool cover which will be installed at the top of reactor pool. The pool cover is classified as non-nuclear safety, seismic category II and quality class T. The basic design of the pool cover for increasing HANARO applications has been carried out for supporting the driving devices which can load, unload and rotate the irradiation targets in the in-core and out-core vertical irradiation holes under on-power operation. The comments of HANARO user group related with irradiation tests have optimally considered in the process of design. The interference between fuel handling and control absorber units in the reactor pool and activities to load, unload and rotate the irradiation targets at the top of the reactor pool have been minimized. The pool cover can be moved for maintenance and can protect the reactor pool from unexpected drop of foreign materials. It provides the space to vertical access of driving devices for NTD, CT/IR and OR4/OR5 under on-power operation. And the pool cover assembly must maintain its structural integrity under seismic load. Based on the above design concept, the HANARO pool cover has been proposed as supporting structure of driving devices for NTD, fission moly and RI production under on-power operation.

Fusion reactor materials program plan. Section III. Plasma material interaction

International Nuclear Information System (INIS)

1978-07-01

A discussion of materials-related problems and an analysis of such problems is given for each major topical area. The strategy that will be used to solve the materials problems is described. As part of this program strategy, a series of major milestones is identified that extends over the next 20 years. Detailed task descriptions for the next five years leading to the achievement of the major milestones are given. Each task is described on a separate page (or task sheet) which includes the task number, task title, objective, scope, and the major milestones addressed by the task. Secondary milestones within a given task or subtask are defined, together with a priority assignment and an estimate of man-years to accomplish the work. Each Plan is organized along major topics which parallel the Subtask organization of the Task Group responsible for the Plan

46{sup th} Annual meeting on nuclear technology (AMNT 2015). Key topics / Outstanding know-how and sustainable innovations / Enhanced safety and operation excellence

Energy Technology Data Exchange (ETDEWEB)

Schaffrath, Andreas; Scheuerer, Martina [Gesellschaft fuer Anlagen- und Reaktorsicherheit mbH (GRS), Garching (Germany); Oenneby Carina; Benjaminsson, Ulf [Westinghouse Electric Sweden AB, Vaesteraes (Sweden). Europe, Middle East and Africa (EMEA)

2015-11-15

Summary report on the Topical Sessions ''CFD Simulations for Reactor Safety Relevant Objectives '' and ''Fuel Management During the Last Cycles and Beyond'' of the 46th Annual Conference on Nuclear Technology (AMNT 2015) held in Berlin, 5 to 7 May 2015. Other Sessions of AMNT 2015 have been covered in atw 7 to 10 (2015) and will be covered in further issues of atw.

Geothermal systems materials: a workshop/symposium

Energy Technology Data Exchange (ETDEWEB)

1978-01-01

Sixteen papers are included. A separate abstract was prepared for each. Summaries of workshops on the following topics are also included in the report: non-metallic materials, corrosion, materials selection, fluid chemistry, and failure analysis. (MHR)

Topical anesthetic versus lidocaine infiltration in arteriovenous fistula cannulation

Directory of Open Access Journals (Sweden)

Anisha George

2014-01-01

Full Text Available Background: End stage renal disease (ESRD patients on maintenance hemodialysis undergo arterio-venous fistula (AVF cannulation prior to each hemodialysis session for blood access. Prior to cannulation lidocaine infiltration is done, which is often perceived as painful. Eutectic mixture of local anesthetic (EMLA has been found to significantly reduce pain associated with radial artery cannulation compared with lidocaine infiltration. Aims: To evaluate the efficacy of EMLA compared to infiltration of lidocaine in hemodialysis patients for AVF cannulation. Materials and Methods: A single-centre, crossover study of patients with an AVF on regular maintenance hemodialysis was performed in the dialysis unit of a tertiary care teaching hospital. The site of AVF, number of attempts for AVF cannulation and cannula insertion time were recorded. The patients were asked about the acceptability of application of the anesthetic, delay between anesthetic and cannulation and to score the pain on cannulation. Results: Fifty patients were included in the study. With the visual analog scale, pain score on infiltration was 4.8. Pain score on cannulation after topical application was 2.9 and after infiltration, 2.0. The number of attempts for cannulation and the cannula insertion time were similar. Anesthesia was more stressful in the injectable group rather than the topical group (P < 0.001. Delay between anesthetic and cannulation was unacceptable in the topical group (P < 0.001. Patient compliance was better during infiltration compared to topical (P < 0.005. Mean pain score during infiltration of anesthetic was significantly higher than cannulation pain after either anesthetic, although pain on cannulation was higher in the topical group (P < 0.001. Conclusions: EMLA offers a suitable alternative to lidocaine infiltration for patients using AVF for blood access.

Money, the Banking System and Monetary Policy in Canada: A Teaching Unit.

Science.gov (United States)

Curtis, Douglas C. A.; Staunton, Ted, Ed.

One of a series of teaching units designed to introduce secondary school students to the Canadian economy, this handbook contains instructional materials on Canada's monetary system and policy. Material is organized and presented in terms of specific topic readings and illustrative activities. The topics covered in six sections are money, the…

Effect of Topical Tacrolimus on Vitiligo in Children

Directory of Open Access Journals (Sweden)

Mohammed Ziaur Rahman Bhuiyan

2016-01-01

Full Text Available Background: Considering safe treatment modalities for children with vitiligo, search for newer therapeutic agents continues. Hence, new immunomodulatory agents such as calcineurinantagonists, frequently referred to as topical immunomodulators (TIMs have recently been introduced as new promising tools to treat acquired hypopigmentary disorders. Tacrolimus is safe in treating children due to lack of skin atrophy and less data are available on effect of topical tacrolimus on vitiligo. Objective: To see the effect of topical tacrolimus on vitiligo in children. Materials and Methods: This prospective study was done in outpatient department of Dermatology and Venereology, Chittagong Medical College Hospital (CMCH, Bangladesh. Clinically diagnosed vitiligo patients of up to 12 years age visiting Skin & VD OPD, CMCH during study period were the study population (total 30. The study was carried out from November 2007 to April 2008. Results: A total of 30 patients, 13 (43.33% males and 17 (56.66% females with focal, segmental or generalized vitiligo were studied. Seventy percent of study subjects were from 7–12 years of age. Topical tacrolimus 0.03% ointment was administered twice daily for 12 weeks to each patient. Repigmentation was complete (>75% in 43.33% cases (13/30, was moderate (50–75% in 33.33% (10/30, mild (<50% in 13.33% (4/30. Clinical adverse effects were noted in 6.67% (2/30 of cases where pruritus was in 3.33% (1/30 and burning in 3.33% (1/30. None of the reactions was severe, all were mild and well-tolerated and most occurred within the first month of initiation of treatment and resolved with continued use of drug and completely cured after the treatment completed. Nobody had to discontinue the therapy for side effects. Conclusion: In conclusion, tacrolimus ointment may be a rapidly efficacious and safe option for the treatment of vitiligo in children. The ease of topical self-administration with minimal side effects makes this novel

Topical steroid-damaged skin

Directory of Open Access Journals (Sweden)

Anil Abraham

2014-01-01

Full Text Available Topical steroids, commonly used for a wide range of skin disorders, are associated with side effects both systemic and cutaneous. This article aims at bringing awareness among practitioners, about the cutaneous side effects of easily available, over the counter, topical steroids. This makes it important for us as dermatologists to weigh the usefulness of topical steroids versus their side effects, and to make an informed decision regarding their use in each individual based on other factors such as age, site involved and type of skin disorder.

Mental Mechanisms for Topics Identification

Directory of Open Access Journals (Sweden)

Louis Massey

2014-01-01

Full Text Available Topics identification (TI is the process that consists in determining the main themes present in natural language documents. The current TI modeling paradigm aims at acquiring semantic information from statistic properties of large text datasets. We investigate the mental mechanisms responsible for the identification of topics in a single document given existing knowledge. Our main hypothesis is that topics are the result of accumulated neural activation of loosely organized information stored in long-term memory (LTM. We experimentally tested our hypothesis with a computational model that simulates LTM activation. The model assumes activation decay as an unavoidable phenomenon originating from the bioelectric nature of neural systems. Since decay should negatively affect the quality of topics, the model predicts the presence of short-term memory (STM to keep the focus of attention on a few words, with the expected outcome of restoring quality to a baseline level. Our experiments measured topics quality of over 300 documents with various decay rates and STM capacity. Our results showed that accumulated activation of loosely organized information was an effective mental computational commodity to identify topics. It was furthermore confirmed that rapid decay is detrimental to topics quality but that limited capacity STM restores quality to a baseline level, even exceeding it slightly.

Topics in nuclear and radiochemistry for college curricula and high school science programs

Energy Technology Data Exchange (ETDEWEB)

1990-01-01

The concern with the current status and trends of nuclear chemistry and radiochemistry education in academic institutions was addressed in a recent workshop. The 1988 workshop considered the important contributions that scientist with nuclear and radiochemistry backgrounds have made and are continuing to make to other sciences and to various applied fields. Among the areas discussed were environmental studies, life sciences, materials science, separation technology, hot atom chemistry, cosmochemistry, and the rapidly growing field of nuclear medicine. It is intent of the organizer and participants of this symposium entitled Topics in Nuclear and Radiochemistry for College Curricula and High School Science Program'' to provide lecture material on topics related to nuclear and radiochemistry to educators. It is our hope that teachers, who may or may not be familiar with the field, will find this collections of articles useful and incorporate some of them into their lectures.

Active-learning Strategies for Legal Topics and Substance Abuse in a Pharmacy Curriculum.

Science.gov (United States)

Steinhardt, Sarah J; Clark, John E; Kelly, William N; Hill, Angela M

2017-02-25

Objective. To implement active-learning strategies to engage students in learning, applying, and teaching legal and substance abuse topics. Design. Medication Safety course student groups created films on a National Patient Safety Goal (NPSG) using a movie genre and presented them in film festival format. Pharmacogenomics course student groups taught ethical, legal, and social implications (ELSI) topics through presentation of short stories about comic book characters with genetic mutations. Students in the Drugs of Abuse course composed and performed dances depicting the mechanism of action of a drug in an in-class rave dance format. Assessment. Course evaluations revealed student engagement with subject material and enjoyment of the creative applications, critical thinking, and collaborative aspects of the activities. Students performed well on examination questions and graded assignments. Conclusion. These active-learning strategies facilitated students' abilities to learn, apply, and teach material in medication safety, pharmacogenomics, and substance abuse courses.

Topics in nuclear and radiochemistry for college curricula and high school science programs

International Nuclear Information System (INIS)

1990-01-01

The concern with the current status and trends of nuclear chemistry and radiochemistry education in academic institutions was addressed in a recent workshop. The 1988 workshop considered the important contributions that scientist with nuclear and radiochemistry backgrounds have made and are continuing to make to other sciences and to various applied fields. Among the areas discussed were environmental studies, life sciences, materials science, separation technology, hot atom chemistry, cosmochemistry, and the rapidly growing field of nuclear medicine. It is intent of the organizer and participants of this symposium entitled ''Topics in Nuclear and Radiochemistry for College Curricula and High School Science Program'' to provide lecture material on topics related to nuclear and radiochemistry to educators. It is our hope that teachers, who may or may not be familiar with the field, will find this collections of articles useful and incorporate some of them into their lectures

Materials resistant to seawater

International Nuclear Information System (INIS)

Lunde, L.

1986-03-01

The report is a summary of the topics discussed at a two-day seminar at Institute for Energy Technology, Kjeller in August 1985. Experience with seawater corrosion in Nordic power reactor plants was discussed. There was also input from Danish experience with seawater corrosion in coal fired power plants. The following topics were dealt with: Experience in seawater cooling system materials, chlorination of seawater systems, and accelerated laboratory tests for stainless steels

Method validation and stability study of quercetin in topical emulsions

Directory of Open Access Journals (Sweden)

Rúbia Casagrande

2009-01-01

Full Text Available This study validated a high performance liquid chromatography (HPLC method for the quantitative evaluation of quercetin in topical emulsions. The method was linear within 0.05 - 200 μg/mL range with a correlation coefficient of 0.9997, and without interference in the quercetin peak. The detection and quantitation limits were 18 and 29 ng/mL, respectively. The intra- and inter-assay precisions presented R.S.D. values lower than 2%. An average of 93% and 94% of quercetin was recovered for non-ionic and anionic emulsions, respectively. The raw material and anionic emulsion, but not non-ionic emulsion, were stable in all storage conditions for one year. The method reported is a fast and reliable HPLC technique useful for quercetin determination in topical emulsions.

Energy Materials Coordinating Committee (EMACC). Annual Technical Report, Fiscal Year 1978

Energy Technology Data Exchange (ETDEWEB)

none,

1978-08-01

The Department of Energy Materials Coordinating Committee (EMACC) completed its first year of activity in FY 1978. A major project during the year was to conduct a survey of topical areas and prepare the report, Survey and Analysis of Selected Topics within the Department of Energy's Materials Research and Development Programs. Seven topics selected were those that had a high level of Divisional interest and supplement those reported in FY 1977 in DOE/ET-0006. The topics and the EMACC panel leaders in charge of compiling information were: 1. Joining of Materials, E.E. Hoffman and E. Dalder; 2. Elastomers R. Nelson; 3. Catalysts and Catalytic Effects R. Epple; 4. Radiation Effects K. Zwilsky; 5. Superconductivity W. Clinton; 6. Cement and Concrete L. Kukacka BNL/R. Reeber; and 7. Alternate Materials R.R. Reeber The report summarizes over 250 projects in these areas and completes the initial review started by James Swisher FY 1977 EMACC Chairman.

Proposed industrial recovered materials utilization targets for the metals and metal-products industry

Energy Technology Data Exchange (ETDEWEB)

None

1979-05-01

The introductory chapter provides a discussion of the factors that affect the recovery and reuse of secondary materials and the competition between the primary and secondary metals industries. It discusses these industries in terms of resource characteristics, industry technology, pollution control requirements, market structure, the economics of recycling, and the issues involved in econometrically estimating scrap supply response behavior. It further presents the methodology established by DOE for the metals, textiles, rubber, and pulp and paper industries. The areas in which government policies might have a significant impact on the utilization of primary and secondary metals and on any recycling targets between now and 1987 are noted. Chapter 3 presents general profiles for the major industrial segments comprising SIC 33. The profiles include such topics as industry structure, process technology, materials and recycling flow, and future trends. Chapter 4 specifically covers the evaluation of recycling targets for the ferrous, aluminum, copper, zinc, and lead industries. (MCW)

Foundations of low-temperature plasma enhanced materials synthesis and etching

Science.gov (United States)

Oehrlein, Gottlieb S.; Hamaguchi, Satoshi

2018-02-01

Low temperature plasma (LTP)-based synthesis of advanced materials has played a transformational role in multiple industries, including the semiconductor industry, liquid crystal displays, coatings and renewable energy. Similarly, the plasma-based transfer of lithographically defined resist patterns into other materials, e.g. silicon, SiO2, Si3N4 and other electronic materials, has led to the production of nanometer scale devices that are the basis of the information technology, microsystems, and many other technologies based on patterned films or substrates. In this article we review the scientific foundations of both LTP-based materials synthesis at low substrate temperature and LTP-based isotropic and directional etching used to transfer lithographically produced resist patterns into underlying materials. We cover the fundamental principles that are the basis of successful application of the LTP techniques to technological uses and provide an understanding of technological factors that may control or limit material synthesis or surface processing with the use of LTP. We precede these sections with a general discussion of plasma surface interactions, the LTP-generated particle fluxes including electrons, ions, radicals, excited neutrals and photons that simultaneously contact and modify surfaces. The surfaces can be in the line of sight of the discharge or hidden from direct interaction for structured substrates. All parts of the article are extensively referenced, which is intended to help the reader study the topics discussed here in more detail.

Cover stones on liquefiable soil bed under waves

DEFF Research Database (Denmark)

Sumer, B. Mutlu; Hatipoglu, Figen; Fredsøe, Jørgen

2010-01-01

The paper describes the results of an experimental study on the behavior of cover stones on a liquefiable soil bed exposed to a progressive wave. The soil was silt with d50=0.098mm. Stones, the size of 4cm, were used as cover material. The effect of packing density of stones, and that of number...... of stone layers (including the effect of an intermediate filter layer) were investigated. Pore pressure was measured across the soil depth. The experiments show that the soil liquefaction depended mainly on two parameters: the packing density of stones, and the number of stone layers. When the liquefaction...

Summary of SMIRT20 Preconference Topical Workshop - Identifying Structural Issues in Advanced Reactors

International Nuclear Information System (INIS)

Richins, William; Novascone, Stephen; O'Brien, Cheryl

2009-01-01

The Idaho National Laboratory (INL, USA) and IASMiRT sponsored an international forum Nov 5-6, 2008 in Porvoo, Finland for nuclear industry, academic, and regulatory representatives to identify structural issues in current and future advanced reactor design, especially for extreme conditions and external threats. The purpose of this Topical Workshop was to articulate research, engineering, and regulatory Code development needs. The topics addressed by the Workshop were selected to address critical industry needs specific to advanced reactor structures that have long lead times and can be the subject of future SMiRT technical sessions. The topics were; (1) structural/materials needs for extreme conditions and external threats in contemporary (Gen. III) and future (Gen. IV and NGNP) advanced reactors and (2) calibrating simulation software and methods that address topic 1. The workshop discussions and research needs identified are presented. The Workshop successfully produced interactive discussion on the two topics resulting in a list of research and technology needs. It is recommended that IASMiRT communicate the results of the discussion to industry and researchers to encourage new ideas and projects. In addition, opportunities exist to retrieve research reports and information that currently exists, and encourage more international cooperation and collaboration. It is recommended that IASMiRT continue with an off-year workshop series on select topics.

Symposium on international safeguards: Verification and nuclear material security. Book of extended synopses. Addendum

International Nuclear Information System (INIS)

2001-01-01

The symposium covered the topics related to international safeguards, verification and nuclear materials security, namely: verification and nuclear material security; the NPT regime: progress and promises; the Additional Protocol as an important tool for the strengthening of the safeguards system; the nuclear threat and the nuclear threat initiative. Eighteen sessions dealt with the following subjects: the evolution of IAEA safeguards ( including strengthened safeguards, present and future challenges; verification of correctness and completeness of initial declarations; implementation of the Additional Protocol, progress and experience; security of material; nuclear disarmament and ongoing monitoring and verification in Iraq; evolution of IAEA verification in relation to nuclear disarmament); integrated safeguards; physical protection and illicit trafficking; destructive analysis for safeguards; the additional protocol; innovative safeguards approaches; IAEA verification and nuclear disarmament; environmental sampling; safeguards experience; safeguards equipment; panel discussion on development of state systems of accountancy and control; information analysis in the strengthened safeguard system; satellite imagery and remote monitoring; emerging IAEA safeguards issues; verification technology for nuclear disarmament; the IAEA and the future of nuclear verification and security

KEY TOPICS IN SPORTS MEDICINE

Directory of Open Access Journals (Sweden)

Amir Ali Narvani

2006-12-01

Full Text Available Key Topics in Sports Medicine is a single quick reference source for sports and exercise medicine. It presents the essential information from across relevant topic areas, and includes both the core and emerging issues in this rapidly developing field. It covers: 1 Sports injuries, rehabilitation and injury prevention, 2 Exercise physiology, fitness testing and training, 3 Drugs in sport, 4 Exercise and health promotion, 5 Sport and exercise for special and clinical populations, 6 The psychology of performance and injury. PURPOSE The Key Topics format provides extensive, concise information in an accessible, easy-to-follow manner. AUDIENCE The book is targeted the students and specialists in sports medicine and rehabilitation, athletic training, physiotherapy and orthopaedic surgery. The editors are authorities in their respective fields and this handbook depends on their extensive experience and knowledge accumulated over the years. FEATURES The book contains the information for clinical guidance, rapid access to concise details and facts. It is composed of 99 topics which present the information in an order that is considered logical and progressive as in most texts. Chapter headings are: 1. Functional Anatomy, 2. Training Principles / Development of Strength and Power, 3. Biomechanical Principles, 4. Biomechanical Analysis, 5. Physiology of Training, 6. Monitoring of Training Progress, 7. Nutrition, 8. Hot and Cold Climates, 9. Altitude, 10. Sport and Travelling, 11. Principles of Sport Injury Diagnosis, 12. Principles of Sport and Soft Tissue Management, 13. Principles of Physical Therapy and Rehabilitation, 14. Principles of Sport Injury Prevention, 15. Sports Psychology, 16. Team Sports, 17. Psychological Aspects of Injury in Sport, 18. Injury Repair Process, 19. Basic Biomechanics of Tissue Injury, 20. Plain Film Radiography in Sport, 21. Nuclear Medicine, 22. Diagnostic Ultrasound, 23. MRI Scan, 24. Other Imaging, 5. Head Injury, 26. Eye

6. International conference on materials science and condensed matter physics. Abstracts

International Nuclear Information System (INIS)

2012-09-01

This book includes abstracts of the communications presented at the 6th International Conference on Materials Science and Condensed Matter Physics. The aim of this event is two-fold. First, it provides a nice opportunity for discussions and the dissemination of the latest results on selected topics in materials science, condensed-matter physics, and electrical methods of materials treatment. On the other hand, this is an occasion for sketching a broad perspective of scientific research and technological developments for the participants through oral and poster presentations. The abstracts presented in the book cover certain issues of modern theoretical and experimental physics and advanced technology, such as crystal growth, doping and implantation, fabrication of solid state structures; defect engineering, methods of fabrication and characterization of nanostructures including nanocomposites, nanowires and nano dots; fullerenes and nano tubes; quantum wells and superlattices; molecular-based materials, meso- and nano electronics; methods of structural and mechanical characterization; optical, transport, magnetic and superconductor properties, non-linear phenomena, size and interface effects; condensed matter theory; modelling of materials and structural properties including low dimensional systems; advanced materials and fabrication processes, device modelling and simulation of structures and elements; optoelectronics and photonics; microsensors and micro electro-mechanical systems; degradation and reliability, advanced technologies of electro-physico-chemical methods and equipment for materials machining, including modification of surfaces; electrophysical technologies of intensification of heat- and mass-transfer; treatment of biological preparations and foodstuff.

Topical Treatment of Degenerative Knee Osteoarthritis.

Science.gov (United States)

Meng, Zengdong; Huang, Rongzhong

2018-01-01

This article reviews topical management strategies for degenerative osteoarthritis (OA) of the knee. A search of Pubmed, Embase and the Cochrane library using MeSH terms including "topical," "treatment," "knee" and "osteoarthritis" was carried out. Original research and review articles on the effectiveness and safety, recommendations from international published guidelines and acceptability studies of topical preparations were included. Current topical treatments included for the management of knee OA include topical nonsteroidal anti-inflammatory drugs, capsaicin, salicylates and physical treatments such as hot or cold therapy. Current treatment guidelines recommend topical nonsteroidal anti-inflammatory drugs as an alternative and even first-line therapy for OA management, especially among elderly patients. Guidelines on other topical treatments vary, from recommendations against their use, to in favor as alternative or simultaneous therapy, especially for patients with contraindications to other analgesics. Although often well-tolerated and preferred by many patients, clinical care still lags in the adoption of topical treatments. Aspects of efficacy, safety and patient quality of life data require further research. Copyright © 2018 Southern Society for Clinical Investigation. Published by Elsevier Inc. All rights reserved.

Correlated Topic Vector for Scene Classification.

Science.gov (United States)

Wei, Pengxu; Qin, Fei; Wan, Fang; Zhu, Yi; Jiao, Jianbin; Ye, Qixiang

2017-07-01

Scene images usually involve semantic correlations, particularly when considering large-scale image data sets. This paper proposes a novel generative image representation, correlated topic vector, to model such semantic correlations. Oriented from the correlated topic model, correlated topic vector intends to naturally utilize the correlations among topics, which are seldom considered in the conventional feature encoding, e.g., Fisher vector, but do exist in scene images. It is expected that the involvement of correlations can increase the discriminative capability of the learned generative model and consequently improve the recognition accuracy. Incorporated with the Fisher kernel method, correlated topic vector inherits the advantages of Fisher vector. The contributions to the topics of visual words have been further employed by incorporating the Fisher kernel framework to indicate the differences among scenes. Combined with the deep convolutional neural network (CNN) features and Gibbs sampling solution, correlated topic vector shows great potential when processing large-scale and complex scene image data sets. Experiments on two scene image data sets demonstrate that correlated topic vector improves significantly the deep CNN features, and outperforms existing Fisher kernel-based features.

Topical treatment of psoriasis: questionnaire results on topical therapy accessibility and influence of body surface area on usage.

Science.gov (United States)

Iversen, L; Lange, M M; Bissonette, R; Carvalho, A V E; van de Kerkhof, P C; Kirby, B; Kleyn, C E; Lynde, C W; van der Walt, J M; Wu, J J

2017-07-01

Topical treatment of mild to moderate psoriasis is first-line treatment and exhibits varying degrees of success across patient groups. Key factors influencing treatment success are physician topical treatment choice (high efficacy, low adverse events) and strict patient adherence. Currently, no formalized, international consensus guidelines exist to direct optimal topical treatment, although many countries have national guidelines. To describe and analyse cross-regional variations in the use and access of psoriasis topical therapies. The study was conducted as an observational cross-sectional study. A survey was distributed to dermatologists from the International Psoriasis Council (IPC) to assess topical therapy accessibility in 26 countries and to understand how body surface area (BSA) categories guide clinical decisions on topical use. Variation in the availability of tars, topical retinoids, dithranol and balneotherapy was reported. The vast majority of respondents (100% and 88.4%) used topical therapy as first-line monotherapy in situations with BSA 10%, the number of respondents who prescribe topical therapy decreased considerably. In addition, combination therapy of a topical drug and a systemic drug was frequently reported when BSA measured >10%. This physician survey provides new evidence on topical access and the influence of disease severity on topical usage in an effort to improve treatment strategies on a global level. © 2017 European Academy of Dermatology and Venereology.

Assessment of land cover changes in Lampedusa Island (Italy) using Landsat TM and OLI data

Science.gov (United States)

Mei, Alessandro; Manzo, Ciro; Fontinovo, Giuliano; Bassani, Cristiana; Allegrini, Alessia; Petracchini, Francesco

2016-10-01

The Lampedusa Island displays important socio-economic criticalities related to an intensive touristic activity, which implies an increase in electricity consumption and waste production. An adequate island conversion to a more environmental, sustainable community needs to be faced by the local Management Plans establishment. For this purpose, several thematic datasets have to be produced and evaluated. Socio-economic and bio-ecological components as well as land cover/use assessment are some of the main topics to be managed within the Decision Support Systems. Considering the lack of Land Cover (LC) and vegetation change detection maps in Lampedusa Island (Italy), this paper focuses on the retrieval of these topics by remote sensing techniques. The analysis was carried out by Landsat 5 TM and Landsat 8 OLI multispectral images from 1984 to 2014 in order to obtain spatial and temporal information of changes occurred in the island. Firstly, imagery was co-registered and atmospherically corrected; secondly, it was then classified for land cover and vegetation distribution analysis with the use of QGIS and Saga GIS open source softwares. The Maximum Likelihood Classifier (MLC) was used for LC maps production, while the Normalized Difference Vegetation Index (NDVI) was used for vegetation examination and distribution. Topographic maps, historical aerial photos, ortophotos and field data are merged in the GIS for accuracy assessment. Finally, change detection of MLC and NDVI are provided respectively by Post-Classification Comparison (PCC) and Image Differencing (ID). The provided information, combined with local socio-economic parameters, is essential for the improvement of environmental sustainability of anthropogenic activities in Lampedusa.

Results from a full scale application of ashes and other residuals in the final cover construction of the Tveta landfill; Utvaerdering av fullskaleanvaendning av askor och andra restprodukter vid sluttaeckning av Tveta Aatervinningsanlaeggning

Energy Technology Data Exchange (ETDEWEB)

Tham, Gustav (Telge AB, Soedertaelje (Sweden)); Andreas, Lale (Luleaa Univ. of Technology, Luleaa (Sweden))

2008-06-15

In 2000 Telge Aatervinning - a waste management and recycling company - started investigating ashes from incineration of industrial and biowaste waste. The company was given a permit from the Swedish Environmental Court to cover four hectares of the house hold waste landfill area. In 2006 the company received an unlimited permit to cover the remaining part of the landfill when the works end some thirty years later. Ashes were used the first time in 1966 for testing. Literature studies indicated the ashes can have a low hydraulic conductivity under certain conditions. In 1999 collaboration started with the Division of Waste Science and Technology at Luleaa University of Technology. Residuals from household and industrial waste were subject to investigation. Initially, biowaste incineration products were subject to testing and were later extended to other waste products, e.g. sludge, contaminated soils, foundry, and compost material. Several different sub-fractions of ashes were included in the investigation e.g. bottom and fly ash, various slag products after up-grading including dewatering, separation and sifting. Subsequently, a complete covering system of a landfill consists of residuals. Six test areas were outlined in order to give a good representation for cover construction in flat and steep areas with different compositions of liner material. The results show that in all areas the hydraulic conductivity construction yields less then 50 liters per square meters and years and can be less the than 5 liters in a repository for hazardous waste if required. In accordance with literature data the field observations show the liner material constructed only by ash material under certain conditions can form a monolithic structure due to very slow processes thus indicating small pore volumes that unable water air to interact with other media. The concept of using ash can be related to natural analogues of volcanic ashes and has been used in old defence walls and other

Design and computation of modern engineering materials

CERN Document Server

Altenbach, Holm

2014-01-01

 The idea of this monograph is to present the latest results related to design and computation of engineering materials and structures. The contributions cover the classical fields of mechanical, civil and materials engineering up to biomechanics and advanced materials processing and optimization. The materials and structures covered can be categorized into modern steels and titanium alloys, composite materials, biological and natural materials, material hybrids and modern joining technologies. Analytical modelling, numerical simulation, the application of state-of-the-art design tools and sophisticated experimental techniques are applied to characterize the performance of materials and to design and optimize structures in different fields of engineering applications.

Topics in quantum groups and finite-type invariants mathematics at the independent University of Moscow

CERN Document Server

Arkhipov, S M; Odesskii, A V; Feigin, B; Vassiliev, V

1998-01-01

This volume presents the first collection of articles consisting entirely of work by faculty and students of the Higher Mathematics College of the Independent University of Moscow (IUM). This unique institution was established to train elite students to become research scientists. Covered in the book are two main topics: quantum groups and low-dimensional topology. The articles were written by participants of the Feigin and Vassiliev seminars, two of the most active seminars at the IUM.

Topics in atomic physics

CERN Document Server

Burkhardt, Charles E

2006-01-01

The study of atomic physics propelled us into the quantum age in the early twentieth century and carried us into the twenty-first century with a wealth of new and, in some cases, unexplained phenomena. Topics in Atomic Physics provides a foundation for students to begin research in modern atomic physics. It can also serve as a reference because it contains material that is not easily located in other sources. A distinguishing feature is the thorough exposition of the quantum mechanical hydrogen atom using both the traditional formulation and an alternative treatment not usually found in textbooks. The alternative treatment exploits the preeminent nature of the pure Coulomb potential and places the Lenz vector operator on an equal footing with other operators corresponding to classically conserved quantities. A number of difficult to find proofs and derivations are included as is development of operator formalism that permits facile solution of the Stark effect in hydrogen. Discussion of the classical hydrogen...

47{sup th} Annual meeting on nuclear technology (AMNT 2016). Key topic / Outstanding know-how and sustainable innovations

Energy Technology Data Exchange (ETDEWEB)

Zwermann, Winfried [Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) gGmbH, Garching (Germany). Forschungszentrum

2016-11-15

Summary report on the Key Topic ''Outstanding Know-How and Sustainable Innovations'' Technical Session ''Reactor Physics, Thermo, and Fluid Dynamics'' of the 47th Annual Conference on Nuclear Technology (AMNT 2016) held in Hamburg, 10 to 12 May 2016. Other Sessions of AMNT 2016 have been and will be covered in further issues of atw.

Lasers in materials science

CERN Document Server

Ossi, Paolo; Zhigilei, Leonid

2014-01-01

This book covers various aspects of lasers in materials science, including a comprehensive overview on basic principles of laser-materials interactions and applications enabled by pulsed laser systems.  The material is organized in a coherent way, providing the reader with a harmonic architecture. While systematically covering the major current and emerging areas of lasers processing applications, the Volume provides examples of targeted modification of material properties achieved through careful control of the processing conditions and laser irradiation parameters. Special emphasis is placed on specific strategies aimed at nanoscale control of material structure and properties to match the stringent requirements of modern applications.  Laser fabrication of novel nanomaterials, which expands to the domains of photonics, photovoltaics, sensing, and biomedical applications, is also discussed in the Volume. This book assembles chapters based on lectures delivered at the Venice International School on Lasers...

Ash and sludge covering of mine waste. Benefits and/or risks using ash and sludge for covering of mine waste; Askor och roetslam som taeckskikt foer gruvavfall. Foerdelar och/eller risker med att anvaenda aska och slam som taeckskikt foer gruvavfall

Energy Technology Data Exchange (ETDEWEB)

Baeckstroem, Mattias; Johansson, Inger [Oerebro Univ. (Sweden). Man-Technology-Environment Research Centre

2004-01-01

One of the main sources for metal pollution in Sweden is mine waste. One way to decrease the leaching of metals from mine waste areas is covering which decreases the formation of acid drainage. There is a shortage of appropriate materials to use for covering, and excavation of till and clay from the environment might cause damages on the landscape. Previous studies have demonstrated that sludge and ashes are suitable materials for covering of waste deposits. When covering mine waste with ash and sludge various positive effects would arise, since the production of drainage water decreases as well as the pH increases due to the high buffer-capacity of the ash. In Ervalla outside Oerebro an area with mine waste has been covered with ash and sludge. This area gives a unique possibility to study benefits and/or risks with the covering of mine waste with ash and sludge. This report is a summary of the first phase of the project and the focus has been on characterisation of the material that has been used for covering. Also a monitoring program for the area has started. Preliminary findings indicate that that the covering decreases the leaching of some metals whereas the leaching of some metals increases. A decrease in the concentration of iron, nickel, cobalt and lead was observed and an increase was observed for arsenic, barium, chromium and copper.

National Land Cover Database (NLCD) Land Cover Collection

Data.gov (United States)

U.S. Geological Survey, Department of the Interior — The National Land Cover Database (NLCD) Land Cover Collection is produced through a cooperative project conducted by the Multi-Resolution Land Characteristics (MRLC)...

Effective dose in the manufacturing process of rutile covered welding electrodes.

Science.gov (United States)

Herranz, M; Rozas, S; Pérez, C; Idoeta, R; Núñez-Lagos, R; Legarda, F

2013-03-01

Shielded metal arc welding using covered electrodes is the most common welding process. Sometimes the covering contains naturally occurring radioactive materials (NORMs). In Spain the most used electrodes are those covered with rutile mixed with other materials. Rutile contains some detectable natural radionuclides, so it can be considered a NORM. This paper mainly focuses on the use of MCNP (Monte Carlo N-Particle Transport Code) as a predictive tool to obtain doses in a factory which produces this type of electrode and assess the radiological impact in a specific facility after estimating the internal dose.To do this, in the facility, areas of highest radiation and positions of workers were identified, radioactive content of rutile and rutile covered electrodes was measured, and, considering a worst possible scenario, external dose at working points has been calculated using MCNP. This procedure has been validated comparing the results obtained with those from a pressurised ionisation chamber and TLD dosimeters. The internal dose has been calculated using DCAL (dose and risk calculation). The doses range between 8.8 and 394 μSv yr(-1), always lower than the effective dose limit for the public, 1 mSv yr(-1). The highest dose corresponds to the mixing area.

Topical botulinum toxin.

Science.gov (United States)

Collins, Ashley; Nasir, Adnan

2010-03-01

Nanotechnology is a rapidly growing discipline that capitalizes on the unique properties of matter engineered on the nanoscale. Vehicles incorporating nanotechnology have led to great strides in drug delivery, allowing for increased active ingredient stability, bioavailability, and site-specific targeting. Botulinum toxin has historically been used for the correction of neurological and neuromuscular disorders, such as torticollis, blepharospasm, and strabismus. Recent dermatological indications have been for the management of axillary hyperhydrosis and facial rhytides. Traditional methods of botulinum toxin delivery have been needle-based. These have been associated with increased pain and cost. Newer methods of botulinum toxin formulation have yielded topical preparations that are bioactive in small pilot clinical studies. While there are some risks associated with topical delivery, the refinement and standardization of delivery systems and techniques for the topical administration of botulinum toxin using nanotechnology is anticipated in the near future.

Statistical evaluation of diagnostic performance topics in ROC analysis

CERN Document Server

Zou, Kelly H; Bandos, Andriy I; Ohno-Machado, Lucila; Rockette, Howard E

2016-01-01

Statistical evaluation of diagnostic performance in general and Receiver Operating Characteristic (ROC) analysis in particular are important for assessing the performance of medical tests and statistical classifiers, as well as for evaluating predictive models or algorithms. This book presents innovative approaches in ROC analysis, which are relevant to a wide variety of applications, including medical imaging, cancer research, epidemiology, and bioinformatics. Statistical Evaluation of Diagnostic Performance: Topics in ROC Analysis covers areas including monotone-transformation techniques in parametric ROC analysis, ROC methods for combined and pooled biomarkers, Bayesian hierarchical transformation models, sequential designs and inferences in the ROC setting, predictive modeling, multireader ROC analysis, and free-response ROC (FROC) methodology. The book is suitable for graduate-level students and researchers in statistics, biostatistics, epidemiology, public health, biomedical engineering, radiology, medi...

Topical methotrexate pretreatment enhances the therapeutic effect of topical 5-aminolevulinic acid-mediated photodynamic therapy on hamster buccal pouch precancers.