Experimental demonstration of radiation effects on the performance of a stirling-alternator convertor and candidate materials evaluation

Science.gov (United States)

Mireles, Omar R.

Free-piston Stirling power convertors are under consideration by NASA for service in the Advanced Stirling Radioisotope Generator (ASRG) and Fission Surface Power (FSP) systems to enable aggressive exploration missions by providing a reliable and constant power supply. The ASRG must withstand environmental radiation conditions, while the FSP system must tolerate a mixed neutron and gamma-ray environment resulting from self-irradiation. Stirling-alternators utilize rare earth magnets and a variety of organic materials whose radiation limits dominate service life estimates and shielding requirements. The project objective was to demonstrate the performance of the alternator, identify materials that exhibit excessive radiation sensitivity, identify radiation tolerant substitutes, establish empirical dose limits, and demonstrate the feasibility of cost effective nuclear and radiation tests by selection of the appropriate personnel and test facilities as a function of hardware maturity. The Stirling Alternator Radiation Test Article (SARTA) was constructed from linear alternator components of a Stirling convertor and underwent significant pre-exposure characterization. The SARTA was operated at the Sandia National Laboratories Gamma Irradiation Facility to a dose of over 40 Mrad. Operating performance was within nominal variation, although modestly decreasing trends occurred in later runs as well as the detection of an electrical fault after the final exposure. Post-irradiation disassembly and internal inspection revealed minimal degradation of the majority of the organic components. Radiation testing of organic material coupons was conducted since the majority of the literature was inconsistent. These inconsistencies can be attributed to testing at environmental conditions vastly different than those Stirling-alternator organics will experience during operation. Samples were irradiated at the Texas A&M TRIGA reactor to above expected FSP neutron fluence. A thorough

A Hydraulic Motor-Alternator System for Ocean-Submersible Vehicles

Science.gov (United States)

Aintablian, Harry O.; Valdez, Thomas I.; Jones, Jack A.

2012-01-01

An ocean-submersible vehicle has been developed at JPL that moves back and forth between sea level and a depth of a few hundred meters. A liquid volumetric change at a pressure of 70 bars is created by means of thermal phase change. During vehicle ascent, the phase-change material (PCM) is melted by the circulation of warm water and thus pressure is increased. During vehicle descent, the PCM is cooled resulting in reduced pressure. This pressure change is used to generate electric power by means of a hydraulic pump that drives a permanent magnet (PM) alternator. The output energy of the alternator is stored in a rechargeable battery that powers an on-board computer, instrumentation and other peripherals.The focus of this paper is the performance evaluation of a specific hydraulic motor-alternator system. Experimental and theoretical efficiency data of the hydraulic motor and the alternator are presented. The results are used to evaluate the optimization of the hydraulic motor-alternator system. The integrated submersible vehicle was successfully operated in the Pacific Ocean near Hawaii. A brief overview of the actual test results is presented.

Alternative Energy Systems

Energy Technology Data Exchange (ETDEWEB)

West, M.; Duckers, L.; Lockett, P.; Loughridge, B.; Peatfield, T.; White, P.

1984-01-01

The Coventry (Lanchester) Polytechnic Wave Energy Group has been involved in the United Kingdom wave energy research programme since its inception in 1975. Whilst the work of the group is mainly concerned with wave energy, and currently is directed towards the design of a wave energy device tailored to the needs of isolated/island communities, it has some involvement with other aspects of the alternatives. This conference, dealing with alternative energy systems and their electrical integration and utilisation was engendered by the general interest which the Polytechnic group members have in the alternatives and their use. The scope for electrical integration and utilisation is very broad. Energy for family groups may be provided in a relatively unsophisticated way which is acceptable to them. Small population centres, for example island communities relying upon diesel equipment, can reap the benefits of the alternatives through their ability to accept novel integration schemes and a flexible approach to the use of the energy available. Consumers already enjoying the benefits of a 'firm' electricity grid supply can use energy from a variety of alternative systems, via the grid, without having to modify their energy consumption habits. In addition to the domestic and industrial applications and coastal possibilities, specialist applications in isolated environments have also emerged. The Proceedings detail practical, technical and economic aspects of the alternatives and their electrical integration and utilisation.

Investigation of the Hygrothermal Performance of Alternative Insulation Materials

DEFF Research Database (Denmark)

Rode, Carsten; Kristiansen, Finn Harken; Rasmussen, Niels T.

1999-01-01

The paper gives an account of hygrothermal investigations carried out on some insulation products which are "alternative" to the ones that are traditionally used in Danish constructions. The alternative products are claimed to be friendly both to the environment and to the labour force. The mater......The paper gives an account of hygrothermal investigations carried out on some insulation products which are "alternative" to the ones that are traditionally used in Danish constructions. The alternative products are claimed to be friendly both to the environment and to the labour force...... is determined for the different materials with a guarded hot plate apparatus in which different vapour pressure conditions can be maintained over the specimens. The apparatus and some results are presented.2. Computational analysis of the hygrothermal performance of constructions with alternative insulation...... products.The hygrothermal performance of constructions with alternative insulation products is analysed with a computational model for combined heat and moisture transfer. The analysis concerns both traditional wall and roof constructions with the alternative insulation products, and some alternative...

DEMONSTRATION OF PACKAGING MATERIALS ALTERNATIVES TO EXPANDED POLYSTYRENE

Science.gov (United States)

This report represents the second demonstration of cleaner technologies to support the goals of the 33/50 Program under the EPA Cooperative Agreement No. CR-821848. The report presents assessment results of alternative packaging materials which could potentially replace expanded...

Supporting the material control and accountancy system with physical protection system features

International Nuclear Information System (INIS)

Miyoshi, D.S.; Olson, C.E.; Caskey, D.L.

1984-01-01

Most physical security functions can be accomplished by a range of alternative features. Careful design can provide comparable levels of security regardless of which option is chosen, albeit with possible differences in cost and efficiency. However, the effectiveness and especially the cost and efficiency of the material control and accounting system may be strongly influenced by the selection of a particular design approach to physical security. In this paper, a series of examples are cited to illustrate the effects that particular physical protection design choices may have. The examples have been chosen from several systems engineering projects at facilities within the DOE nuclear community. These examples are generalized, and a series of design principles are proposed for integrating physical security with material control and accounting by appropriate selection of alternative features. 2 references, 6 figures

9975 Shipping Package Performance Of Alternate Materials For Long-Term Storage Application

International Nuclear Information System (INIS)

Skidmore, E.; Hoffman, E.; Daugherty, W.

2010-01-01

The Model 9975 shipping package specifies the materials of construction for its various components. With the loss of availability of material for two components (cane fiberboard overpack and Viton(reg s ign) GLT O-rings), alternate materials of construction were identified and approved for use for transport (softwood fiberboard and Viton(reg s ign) GLT-S O-rings). As these shipping packages are part of a long-term storage configuration at the Savannah River Site, additional testing is in progress to verify satisfactory long-term performance of the alternate materials under storage conditions. The test results to date can be compared to comparable results on the original materials of construction to draw preliminary conclusions on the performance of the replacement materials.

Effect of disinfection on irreversible hydrocolloid and alternative impression materials and the resultant gypsum casts.

Science.gov (United States)

Suprono, Montry S; Kattadiyil, Mathew T; Goodacre, Charles J; Winer, Myron S

2012-10-01

Many new products have been introduced and marketed as alternatives to traditional irreversible hydrocolloid materials. These alternative materials have the same structural formula as addition reaction silicone, also known as vinyl polysiloxane (VPS), impression materials. Currently, there is limited in vitro and in vivo research on these products, including on the effects of chemical disinfectants on the materials. The purpose of this study was to compare the effects of a spray disinfecting technique on a traditional irreversible hydrocolloid and 3 new alternative impression materials in vitro. The tests were performed in accordance with the American National Standards Institute/American Dental Association (ANSI/ADA) Specification Nos. 18 and 19. Under standardized conditions, 100 impressions were made of a ruled test block with an irreversible hydrocolloid and 3 alternative impression materials. Nondisinfected irreversible hydrocolloid was used as the control. The impressions were examined for surface detail reproduction before and after disinfection with a chloramine-T product. Type III and Type V dental stone casts were evaluated for linear dimensional change and gypsum compatibility. Comparisons of linear dimensional change were analyzed with 2-way ANOVA of mean ranks with the Scheffé post hoc comparisons (α=.05). Data for surface detail reproduction were analyzed with the Wilcoxon Signed-Rank procedure and gypsum compatibility with the Kruskal-Wallis Rank procedure (α=.05). The alternative impression materials demonstrated significantly better outcomes with all 3 parameters tested. Disinfection with chloroamine-T did not have any effect on the 3 alternative impression materials. The irreversible hydrocolloid groups produced the most variability in the measurements of linear dimensional change. All of the tested materials were within the ADA's acceptable limit of 1.0% for linear dimensional change, except for the disinfected irreversible hydrocolloid

Development of alternative materials for BWR fuel springs

International Nuclear Information System (INIS)

Uruma, Y.; Osato, T.; Yamazaki, K.

2002-01-01

Major sources of radioactivity introduced into reactor water of BWR were estimated fuel crud and in-core materials (especially, fuel springs). Fuel springs are used for fixation of fuel cladding tubes with spacer grid. Those are small parts (total length is only within 25 mm) and so many numbers are loaded simultaneously and then total surfaces area are calculated up to about 200 m 2 . Fuel springs are located under high radiation field and high oxidative environment. Conventional fuel spring is made of alloy-X750 which is one of nickel-based alloy and is reported to show relatively higher corrosion release rate. 58 Co and 60 Co will be released directly into reactor water from intensely radio-activated fuel springs surface and increase radioactivity concentrations in primary coolant. Corrosion release control from fuel springs is an important technical item and a development of alternative material instead of alloy-X750 for fuel spring is a key subject to achieve ultra low man-rem exposure BWR plant. In present work, alloy-X718 which started usage for PWR fuel springs and stainless steel type 316L which has many mechanical property data are picked up for alternative materials and compared their corrosion behaviors with conventional material. Corrosion experiment was conducted under vapor-water two phases flow which is simulated fuel cladding surface boiling condition. After exposure, corrosion film formed under corrosion test was analyzed in detail and corrosion film amount and corrosion release amount are estimated among three materials. (authors)

Malzeme Taşıma Sistemi Alternatiflerinin Değerlendirilmesinde Bulanık-Promethee Yaklaşımı = Evaluating Material Handling System Alternatives Using Fuzzy-Promethee Approach

Directory of Open Access Journals (Sweden)

Bahadır GÜLSÜN

2011-01-01

Full Text Available Material handling system selection process has an important effect on productivity of manufacturing systems. Considering the importance of this process, it can be seen that there is a necessity to establish a systematic approach. In this study, to determine the best material handling system alternative, PROMETHEE approach is utilized. With the aim of taking into account the vagueness in the evaluation process and obtaining decision maker evaluations in an easier way with linguistic terms, fuzzy sets are utilized. To this end, a modified version of PROMETHEE is used. To foster the better understanding of the methodology, a real life application of a manufacturer is realized.

Solid waste and materials systems alternatives study summary

International Nuclear Information System (INIS)

Kasper, J.R.; Smith, S.T.

1996-01-01

The Hanford Site is a 560-sq.-mi. area in southeastern Washington State owned and operated by the U.S. Department of Energy (DOE). Previous weapons program activities and recent environmental cleanup activities at the Hanford Site have resulted in an accumulation of large quantities of solid wastes and materials. Future Decontamination and Decommissioning (D ampersand D) and Environmental Remediation activities will generate additional wastes. This paper provides a summary of a recently completed analysis of the Hanford Site Solid Wastes and Materials. The analysis involved development and compilation of waste stream and material information including type, classification. location current and project volumes, and curie content. Current program plans for treatment, storage, and disposal/disposition (TSD) have also been included in this analysis

Material challenges for the next generation of fission reactor systems

International Nuclear Information System (INIS)

Buckthorpe, Derek

2010-01-01

The new generation of fission reactor systems wil require the deployment and construction of a series of advanced water cooled reactors as part of a package of measures to meet UK and European energy needs and to provide a near term non-fossil fuel power solution that addresses CO 2 emission limits. In addition new longer term Generation IV reactor tye systems are being developed and evaluated to enhance safety, reliability, sustainability economics and proliferation resistance requirements and to meet alternative energy applications (outside of electricity generation) such as process heat and large scale hydrogen generation. New fission systems will impose significant challenges on materials supply and development. In the near term, because of the need to 'gear up' to large scale construction after decades of industrial hibernation/contraction and, in the longer term, because of the need for materials to operate under more challenging environments requiring the deployment and development of new alternative materials not yet established to an industrial stage. This paper investigates the materials challenges imposed by the new Generation III+ and Generation IV systems. These include supply and fabrication issues, development of new high temperature alloys and non-metallic materials, the use of new methods of manufacture and the best use of currently available resources and minerals. Recommendations are made as to how these materials challenges might be met and how governments, industry, manufacturers and researchers can all play their part. (orig.)

Material challenges for the next generation of fission reactor systems

Energy Technology Data Exchange (ETDEWEB)

Buckthorpe, Derek [AMEC, Knutsford, Cheshire (United Kingdom)

2010-07-01

The new generation of fission reactor systems wil require the deployment and construction of a series of advanced water cooled reactors as part of a package of measures to meet UK and European energy needs and to provide a near term non-fossil fuel power solution that addresses CO{sub 2} emission limits. In addition new longer term Generation IV reactor tye systems are being developed and evaluated to enhance safety, reliability, sustainability economics and proliferation resistance requirements and to meet alternative energy applications (outside of electricity generation) such as process heat and large scale hydrogen generation. New fission systems will impose significant challenges on materials supply and development. In the near term, because of the need to 'gear up' to large scale construction after decades of industrial hibernation/contraction and, in the longer term, because of the need for materials to operate under more challenging environments requiring the deployment and development of new alternative materials not yet established to an industrial stage. This paper investigates the materials challenges imposed by the new Generation III+ and Generation IV systems. These include supply and fabrication issues, development of new high temperature alloys and non-metallic materials, the use of new methods of manufacture and the best use of currently available resources and minerals. Recommendations are made as to how these materials challenges might be met and how governments, industry, manufacturers and researchers can all play their part. (orig.)

Alternative materials for FDOT sign structures : phase I literature review.

Science.gov (United States)

2012-05-01

Inspections of tubular sign structures by the Florida Department of Transportation (FDOT) have : revealed occurrences of premature corrosion on the inside of galvanized steel tubes. As a result, FDOT : engineers are seeking alternative materials that...

Investigations on Cs-free alternative materials for negative hydrogen ion formation

Energy Technology Data Exchange (ETDEWEB)

Kurutz, Uwe

2017-01-19

Neutral beam injection (NBI) represents a main auxiliary heating and current drive system for thermonuclear fusion devices. For ITER, a total heating power of up to 33 MW will be delivered for up to one hour pulses at particle energies of up to 1 MeV by two NBI systems. The respective ion sources will therefore have to allow for the extraction and acceleration of negative hydrogen ions at a current density of 200 A/m{sup 2} from a low pressure low temperature hydrogen plasma. Also for the succeeding demonstration reactor DEMO the application of NBI is currently discussed. Respective systems will, however, have to fulfil even higher demands, like higher powers (up to 135 MW), longer pulse lengths (2 h or even cw operation), and more restrictive constrains regarding the reliability and stability. Today efficient NBI negative hydrogen ion sources are based mainly on the conversion of positive hydrogen ions and/or hydrogen atoms at a grid surface coated with caesium. Cs is used for reducing the grid's work function which significantly enhances the particle conversion probability. However, the alkali metal is chemically very reactive and easily forms compounds with residual gas impurities. Furthermore, complex redistribution dynamics of the deposited Cs layer is given. This inherently links the application of Cs with a temporal and spatial non-stability of the negative ion yield, which contradicts the required reliability of a DEMO NBI system. Thus, for DEMO, Cs-free alternative materials for negative ion formation are investigated within this work at a flexible laboratory experiment. An ECR discharge is used which provides comparable parameters (pressure, densities, particle fluxes and -energies) to the NBI ion sources. Negative ion formation is measured above different material samples via laser photodetachment together with global plasma parameters using a Langmuir probe and optical emission spectroscopy. The plasma parameters are used for modelling the

Investigations on Cs-free alternative materials for negative hydrogen ion formation

International Nuclear Information System (INIS)

Kurutz, Uwe

2017-01-01

Neutral beam injection (NBI) represents a main auxiliary heating and current drive system for thermonuclear fusion devices. For ITER, a total heating power of up to 33 MW will be delivered for up to one hour pulses at particle energies of up to 1 MeV by two NBI systems. The respective ion sources will therefore have to allow for the extraction and acceleration of negative hydrogen ions at a current density of 200 A/m 2 from a low pressure low temperature hydrogen plasma. Also for the succeeding demonstration reactor DEMO the application of NBI is currently discussed. Respective systems will, however, have to fulfil even higher demands, like higher powers (up to 135 MW), longer pulse lengths (2 h or even cw operation), and more restrictive constrains regarding the reliability and stability. Today efficient NBI negative hydrogen ion sources are based mainly on the conversion of positive hydrogen ions and/or hydrogen atoms at a grid surface coated with caesium. Cs is used for reducing the grid's work function which significantly enhances the particle conversion probability. However, the alkali metal is chemically very reactive and easily forms compounds with residual gas impurities. Furthermore, complex redistribution dynamics of the deposited Cs layer is given. This inherently links the application of Cs with a temporal and spatial non-stability of the negative ion yield, which contradicts the required reliability of a DEMO NBI system. Thus, for DEMO, Cs-free alternative materials for negative ion formation are investigated within this work at a flexible laboratory experiment. An ECR discharge is used which provides comparable parameters (pressure, densities, particle fluxes and -energies) to the NBI ion sources. Negative ion formation is measured above different material samples via laser photodetachment together with global plasma parameters using a Langmuir probe and optical emission spectroscopy. The plasma parameters are used for modelling the inherently

Findings and Recommendations from the NIST Workshop on Alternative Fuels and Materials: Biocorrosion.

Science.gov (United States)

Mansfield, Elisabeth; Sowards, Jeffrey W; Crookes-Goodson, Wendy J

2015-01-01

In 2013, the Applied Chemicals and Materials Division of the National Institute of Standards and Technology (NIST) hosted a workshop to identify and prioritize research needs in the area of biocorrosion. Materials used to store and distribute alternative fuels have experienced an increase in corrosion due to the unique conditions caused by the presence of microbes and the chemistry of biofuels and biofuel precursors. Participants in this workshop, including experts from the microbiological, fuel, and materials communities, delved into the unique materials and chemical challenges that occur with production, transport, and storage of alternative fuels. Discussions focused on specific problems including: a) the changing composition of "drop-in" fuels and the impact of that composition on materials; b) the influence of microbial populations on corrosion and fuel quality; and c) state-of-the-art measurement technologies for monitoring material degradation and biofilm formation.

Corrosion evaluation of service water system materials

International Nuclear Information System (INIS)

Stein, A.A.; Felder, C.M.; Martin, R.L.

1994-01-01

The availability and reliability of the service water system is critical for safe operation of a nuclear power plant. Degradation of the system piping and components has forced utilities to re-evaluate the corrosion behavior of current and alternative system materials, to support assessments of the remaining service life of the service water system, selection of replacement materials, implementation of corrosion protection methods and corrosion monitoring programs, and identification of maintenance and operational constraints consistent with the materials used. TU Electric and Stone and Webster developed a service water materials evaluation program for the Comanche Peak Steam Electric Station. Because of the length of exposure and the generic interest in this program by the nuclear power industry, EPRI joined TU to co-sponsor the test program. The program was designed to evaluate the corrosion behavior of current system materials and candidate replacement materials and to determine the operational and design changes which could improve the corrosion performance of the system. Although the test program was designed to be representative of service water system materials and environments targeted to conditions at Comanche Peak, these conditions are typical of and relevant to other fresh water cooled nuclear service water systems. Testing was performed in raw water and water treated with biocide under typical service water operating conditions including continuous flow, intermittent flow, and stagnant conditions. The test program evaluated the 300 Series and 6% molybdenum stainless steels, copper-nickel, titanium, carbon steel, and a formed-in-place nonmetallic pipe lining to determine susceptibility to general, crevice, and microbiologically influenced corrosion and pitting attack. This report presents the results of the test program after 4 years of exposure

Synthesis of material microporous using raw materials alternative as a source of silica and alumina

International Nuclear Information System (INIS)

Santos, E.A.; Silva, T.L.

2014-01-01

Synthetic zeolites have important properties of a technological viewpoint. Thus, this work aims at the use of natural raw materials such as kaolin waste and wood ash in order to produce these microporous materials. The starting materials were characterized by X-ray diffraction (XRD) and spectroscopy, X-ray fluorescence (XRF); the phases formed as synthesis products were identified by XRD and gravimetric and differential thermal analysis (DTA/TG). Hydrothermal synthesis took place by mixing the raw materials in stoichiometrically calculated batches with NaOH (3M) at 90 °C and time of 6, 20, 24 and 48 hours. The results show the formation of phases of type zeolite A and sodalite, demonstrating the raw materials be an efficient and low cost alternative to producing microporous materials. (author)

Use of alternative raw materials for yoghurt production | Farinde ...

African Journals Online (AJOL)

Soymilk and maize steep water were used as alternative raw materials to cow milk and commercial starter, respectively, for production of yoghurt. The cow milk used was both Fresh milk and dried powdered milk (DANO). The cost of production of the yoghurt samples as well as their chemical, microbial and organoleptic ...

BEHAVIOUR OF BACKFILL MATERIALS FOR ELECTRICAL GROUNDING SYSTEMS UNDER HIGH VOLTAGE CONDITIONS

Directory of Open Access Journals (Sweden)

S. C. LIM

2015-06-01

Full Text Available Backfill materials like Bentonite and cement are effective in lowering grounding resistance of electrodes for a considerable period. During lightning, switching impulses and earth fault occurrences in medium and high voltage networks, the grounding system needs to handle extremely high currents either for a short duration or prolonged period respectively. This paper investigates the behaviour of bentonite, cement and sand under impulse and alternating high voltage (50Hz conditions. Fulguritic-formation was observed in all materials under alternating high voltage. The findings reveal that performance of grounding systems under high voltage conditions may significantly change from the outcomes anticipated at design stage.

Full-scale experimentations on alternative materials in roads: analysis of study practices.

Science.gov (United States)

François, D; Jullien, A; Kerzreho, J P; Chateau, L

2009-03-01

In France beginning in the 1990s, the topic of road construction using various alternative materials has given rise to several studies aimed at clarifying the technical and environmental feasibility of such an option. Although crucial to understanding and forecasting their behaviour in the field, an analysis of feedback from onsite experiences (back analysis) of roads built with alternative materials has not yet been carried out. The aim of the CAREX project (2003-2005) has been to fill this gap at the national scale. Based on a stress-response approach applied to both the alternative material and the road structure and including the description of external factors, a dedicated standardised framework for field data classification and analysis was adopted. To carry out this analysis, a set of 17 documented field experiments was identified through a specific national survey. It appears that a great heterogeneity exists in data processing procedures among studies. The description of material is acceptable while it is generally poor regarding external factors and structure responses. Structure monitoring is usually brief and mechanical loads too weak, which limits the significance of field testing. For future full-scale experiments, strengthening the realism within the testing conditions would be appropriate.

Review of magnetic refrigeration system as alternative to conventional refrigeration system

Science.gov (United States)

Mezaal, N. A.; Osintsev, K. V.; Zhirgalova, T. B.

2017-10-01

The refrigeration system is one of the most important systems in industry. Developers are constantly seeking for how to avoid the damage to the environment. Magnetic refrigeration is an emerging, environment-friendly technology based on a magnetic solid that acts as a refrigerant by magneto-caloric effect (MCE). In the case of ferromagnetic materials, MCE warms as the magnetic moments of the atom are aligned by the application of a magnetic field. There are two types of magnetic phase changes that may occur at the Curie point: first order magnetic transition (FOMT) and second order magnetic transition (SOMT). The reference cycle for magnetic refrigeration is AMR (Active Magnetic Regenerative cycle), where the magnetic material matrix works both as a refrigerating medium and as a heat regenerating medium, while the fluid flowing in the porous matrix works as a heat transfer medium. Regeneration can be accomplished by blowing a heat transfer fluid in a reciprocating fashion through the regenerator made of magnetocaloric material that is alternately magnetized and demagnetized. Many magnetic refrigeration prototypes with different designs and software models have been built in different parts of the world. In this paper, the authors try to shed light on the magnetic refrigeration and show its effectiveness compared with conventional refrigeration methods.

Methane Hydrate in Confined Spaces: An Alternative Storage System.

Science.gov (United States)

Borchardt, Lars; Casco, Mirian Elizabeth; Silvestre-Albero, Joaquin

2018-03-14

Methane hydrate inheres the great potential to be a nature-inspired alternative for chemical energy storage, as it allows to store large amounts of methane in a dense solid phase. The embedment of methane hydrate in the confined environment of porous materials can be capitalized for potential applications as its physicochemical properties, such as the formation kinetics or pressure and temperature stability, are significantly changed compared to the bulk system. We review this topic from a materials scientific perspective by considering porous carbons, silica, clays, zeolites, and polymers as host structures for methane hydrate formation. We discuss the contribution of advanced characterization techniques and theoretical simulations towards the elucidation of the methane hydrate formation and dissociation process within the confined space. We outline the scientific challenges this system is currently facing and look on possible future applications for this technology. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Expert systems: an alternative paradigm

Energy Technology Data Exchange (ETDEWEB)

Coombs, M.; Alty, J.

1984-01-01

There has recently been a significant effort by the AI community to interest industry in the potential of expert systems. However, this has resulted in far fewer substantial applications projects than might be expected. This article argues that this is because human experts are rarely required to perform the role that computer-based experts are programmed to adopt. Instead of being called in to answer well-defined problems, they are more often asked to assist other experts to extend and refine their understanding of a problem area at the junction of their two domains of knowledge. This more properly involves educational rather than problem-solving skills. An alternative approach to expert system design is proposed based upon guided discovery learning. The user is provided with a supportive environment for a particular class of problem, the system predominantly acting as an adviser rather than directing the interaction. The environment includes a database of domain knowledge, a set of procedures for its application to a concrete problem, and an intelligent machine-based adviser to judge the user's effectiveness and advise on strategy. The procedures focus upon the use of user generated explanations both to promote the application of domain knowledge and to expose understanding difficulties. Simple database PROLOG is being used as the subject material for the prototype system which is known as MINDPAD. 30 references.

Business System Planning Project, Alternatives Analysis

International Nuclear Information System (INIS)

EVOSEVICH, S.

2000-01-01

The CHG Chief Information Officer (CIO) requested a study of alternatives to the current business system computing environment. This Business Systems Planning (BSP) Project Alternatives Analysis document presents an analysis of the current Project Controls, Work Management, and Business Management systems environment and alternative solutions that support the business functions. The project team has collected requirements and priorities from stakeholders in each business area and documented them in the BSP System Requirements Specification (SRS), RPP-6297. The alternatives analysis process identifies and measures possible solutions in each of the business process areas against the requirements as documented in the SRS. The team gathered input from both internal and external sources to identify and grade the possible solutions. This document captures the results of that activity and recommends a suite of software products. This study was to select the best product based on how well the product met the requirements, not to determine the platform or hardware environment that would be used. Additional analysis documentation can be found in BSP project files

The National Shipbuilding Research Program: Producibility Cost Reductions through Alternative Materials and Processes

National Research Council Canada - National Science Library

Horsmon, Jr., Albert W; Johnson, Karl; Gans-Devney, Barbara

1999-01-01

This report describes research into the use of alternative materials and processes to reduce material and labor costs while also looking at the influence of these choices on the life cycle costs of the vessel...

F- and H-Area Seepage Basins Water Treatment System Process Optimization and Alternative Chemistry Ion Exchange/Sorbent Material Screening Clearwell Overflow Study

Energy Technology Data Exchange (ETDEWEB)

Serkiz, S.M.

2000-08-30

This study investigated alternative ion exchange/sorbent materials and polishing chemistries designed to remove specific radionuclides not removed during the neutralization/precipitation/clarification process.

Alternative materials for solid oxide fuel cells: Factors affecting air-sintering of chromite interconnections

International Nuclear Information System (INIS)

Chick, L.A.; Bates, J.L.

1992-01-01

The purpose of this research is to develop alternative materials for solid oxide fuel cell (SOFC) interconnections and electrodes with improved electrical, thermal and electrochemical properties. Another objective is to develop synthesis and fabrication processes for these materials whereby they can be consolidated in air into SOFC's. The approach is to (1) develop modifications of the current, state-of-the-art materials used in SOFC's, (2) minimize the number of cations used in the SOFC materials to reduce potential deleterious interactions, (3) improve thermal, electrical, and electrochemical properties, (4) develop methods to synthesize both state-of-the-art and alternative materials for the simultaneous fabrication and consolidation in air of the interconnections and electrodes with the solid electrolyte, and (5) understand electrochemical reactions at materials interfaces and the effects of component compositions and processing on those reactions

Supporting the material control and accountancy system with physical protection system features

International Nuclear Information System (INIS)

Miyoshi, D.S.; Caskey, D.L.; Olson, C.E.

1984-01-01

Most physical security functions can be accomplished by a range of alternative features. Careful design can provide comparable levels of security regardless of which option is chosen, albeit with possible differences in cost and efficiency. However, the effectiveness and especially the cost and efficiency of the material control and accounting system may be strongly influenced by the selection of a particular design approach to physical security. In this paper, a series of examples are cited to illustrate the effects that particular physical protection design choices may have. The examples have been chosen from several systems engineering projects at facilities within the DOE nuclear community. These examples are generalized, and a series of design principles are proposed for integrating physical security with MC and A by appropriate selection of alternative features

17 CFR 242.301 - Requirements for alternative trading systems.

Science.gov (United States)

2010-04-01

... trading systems. 242.301 Section 242.301 Commodity and Securities Exchanges SECURITIES AND EXCHANGE... FUTURES Regulation Ats-Alternative Trading Systems § 242.301 Requirements for alternative trading systems. (a) Scope of section. An alternative trading system shall comply with the requirements in paragraph...

Materials and degradation modes in an alternative LLW [low-level waste] disposal facility

International Nuclear Information System (INIS)

Cowgill, M.G.; MacKenzie, D.R.

1989-01-01

The materials used in the construction of alternative low-level waste disposal facilities will be subject to interaction with both the internal and the external environments associated with the facilities and unless precautions are taken, may degrade, leading to structural failure. This paper reviews the characteristics of both environments with respect to three alternative disposal concepts, then assesses how reaction with them might affect the properties of the materials, which include concrete, steel-reinforced concrete, structural steel, and various protective coatings and membranes. It identifies and evaluates the probability of reactions occurring which might lead to degradation of the materials and so compromise the structure. The probability of failure (interpreted relative to the ability of the structure to restrict ingress and egress of water) is assessed for each material and precautionary measures, intended to maximize the durability of the facility, are reviewed. 19 refs., 2 tabs

Use of alternative waste materials in producing ultra-high performance concrete

Directory of Open Access Journals (Sweden)

Ahmad Shamsad

2017-01-01

Full Text Available In a corrosive environment similar to that of the Arabian Gulf, use of high-performance concrete is one of the options to ensure a target service life of concrete structures. However, in absence of good quality coarse aggregates, it is a challenging task to produce high-performance concrete. Recently, the possibility of producing ultra-high-performance concrete (UHPC has been widely reported in the literature. UHPC is produced without coarse aggregates at very low water to cementitious materials ratio, high amounts of cement, mineral admixtures, and superplasticizer along with fine quartz sand as aggregate, quartz powder as micro-filler, a nd steel fibres for fracture toughness. In the present work, an effort was made to utilize local waste materials as alternative mineral admixtures and local dune sand as aggregate in producing different UHPC mixtures without addition of quartz powder. The mechanical properties, shrinkage, and durability characteristics of the UHPC mixtures were studied. Test results indicate that it is possible to produce UHPC mixtures using alternative waste materials, which would have targeted flow, strength, toughness, and resistance against reinforcement corrosion. The information presented in the paper would help in optimum selection of a mixture of UHPC considering the availability of local materials, exposure conditions and structural requirements.

Alternative trading systems in Poland

Directory of Open Access Journals (Sweden)

Magdalena Mosionek-Schweda

2009-12-01

Full Text Available The first Polish alternative trading system – called NewConnect – was opened on 30 August 2007. It has the status of an organized market, but it is operated by the Warsaw Stock Exchange outside the regulated market. Two years later, on 30 September 2009, the WSE launched another market – Catalyst – which consists of four segments including: two regular markets and two alternative trading platforms. The present paper aims to describe fundamental rules of the Polish alternative trading platforms as well as to depict a short overview of their trading indicators and basic statistics.

Alternate electrode materials for the SP100 reactor

International Nuclear Information System (INIS)

Randich, E.

1992-05-01

This work was performed in response to a request by the Astro-Space Division of the General Electric Co. to develop alternate electrodes materials for the electrodes of the PD2 modules to be used in the SP100 thermoelectric power conversion system. Initially, the project consisted of four tasks: (1) development of a ZrB 2 (C) CVD coating on SiMo substrates, (2) development of a ZrB 2 (C) CVD coating on SiGe substrates, (3) development of CVI W for porous graphite electrodes, and (4) technology transfer of pertinent developed processes. The project evolved initially into developing only ZrB 2 coatings on SiGe and graphite substrates, and later into developing ZrB 2 coatings only on graphite substrates. Several sizes of graphite and pyrolytic carbon-coated graphite substrates were coated with ZrB 2 during the project. For budgetary reasons, the project was terminated after half the allotted time had passed. Apart from the production of coated specimens for evaluation, the major accomplishment of the project was the development of the CVD processing to produce the desired coatings

Alternate Material Pallet, 40" x 48", MIL-STD-1660, Engineering Evaluation Tests

National Research Council Canada - National Science Library

Dugan, Jeffery

2003-01-01

The U.S. Army Defense Ammunition Center (DAC), Validation Engineering Division (SJMAC-DEV) conducted Engineering Evaluation Tests to determine if the Alternate Material Pallet manufactured by Hunter Paine Enterprise, Inc...

Towards CMOS-compatible nanophotonics: Ultra-compact modulators using alternative plasmonic materials

DEFF Research Database (Denmark)

Babicheva, Viktoriia; Kinsey, Nathaniel; Naik, Gururaj V.

2013-01-01

We propose several planar layouts of ultra-compact plasmonic modulators that utilize alternative plasmonic materials such as transparent conducting oxides and titanium nitride. The modulation is achieved by tuning the carrier concentration in a transparent conducting oxide layer into and out of t...

Alternative routes for highway shipments of radioactive materials and lessons learned from state designations

International Nuclear Information System (INIS)

1990-07-01

Pursuant to the Hazardous Materials Transportation Act (HMTA), the Department of Transportation (DOT) has promulgated a comprehensive set of regulations regarding the highway transportation of high-level radioactive materials. These regulations, under docket numbers HM-164 and HM-164A, establish interstate highways as the preferred routes for the transportation of radioactive materials within and through the states. The regulations also provide a methodology by which a state may select altemative routes. First, the state must establish a ''state routing agency'', defined as an entity authorized to use the state legal process to impose routing requirements on carriers of radioactive material (49 CFR 171.8). Once identified, the state routing agency must select routes in accordance with DOTs Guidelines for Selecting Preferred Highway Routes for Large Quantity Shipments of Radioactive Materials or an equivalent routing analysis. Adjoining states and localities should be consulted on the impact of proposed alternative routes as a prerequisite of final route selection. Lastly, the states must provide written notice to DOT of any alternative route designation before the routes are deemed effective. The purpose of this report is to discuss the ''lessons learned'' by the five states within the southern region that have designated alternative or preferred routes under the regulations of the Department of Transportation (DOT) established for the transportation of radioactive materials. The document was prepared by reviewing applicable federal laws and regulations, examining state reports and documents and contacting state officials and routing agencies involved in making routing decisions. In undertaking this project, the Southern States Energy Board hopes to reveal the process used by states that have designated alternative routes and thereby share their experiences (i.e., lessons learned) with other southern states that have yet to make designations

( Rosa damascena Mill.) dreg: an alternative litter material in broiler ...

African Journals Online (AJOL)

The present study was carried out to determine the effects of using dried rose dreg (DRD) as an alternative litter material for broiler performance and microbiological characteristics of litter. A total of 225 day-old broiler chicks was raised on pine wood shavings (PS), DRD and PS+DRD until 42 days. The effects of litter ...

Total System Performance Assessment: Enhanced Design Alternative V

International Nuclear Information System (INIS)

N. Erb; S. Miller; V. Vallikat

1999-01-01

This calculation documents the total system performance assessment modeling of Enhanced Design Analysis (EDA) V. EDA V is based on the TSPA-VA base design which has been modified with higher thermal loading, a quartz sand invert, and line loading with 21 PWR waste packages that have 2-cm thick titanium grade 7 corrosion resistance material (CRM) drip shields placed over dual-layer waste packages composed of 'inside out' VA reference material (CRWMS M and O 1999a). This document details the changes and assumptions made to the VA reference Performance Assessment Model (CRWMS M and O 1998a) to incorporate the design changes detailed for EDA V. The performance measure for this evaluation is expected value dose-rate history. Time histories of dose rate are presented for EDA V and a Defense in Depth (DID) analysis base on EDA V. Additional details concerning the Enhanced Design Alternative II are provided in the 'LADS 3-12 Requests' interoffice correspondence (CRWMS M and O 1999a)

Alternative Immune Systems

Directory of Open Access Journals (Sweden)

Luis Fernando Cadavid Gutierrez

2011-09-01

Full Text Available The immune system in animals is a complex network of molecules, cells and tissues that coordinately maintain the physiological and genetic integrity of the organism. Traditionally, two classes of immunity have been considered, the innate immunity and the adaptive immunity. The former is ancestral, with limited variability and low discrimination. The latter is highly variable, specific and limited to jawed vertebrates. Adaptive immunity is based on antigen receptors that rearrange somatically to generate a nearly unlimited diversity of molecules. Likely, this mechanism of somatic recombination arose as a consequence of a horizontal transfer of transposons and transposases from bacterial genomes in the ancestor of jawed vertebrates. The recent discovery in jawless vertebrates and invertebrates of alternative adaptive immune mechanisms, suggests during evolution different animal groups have found alternative solutions to the problem of immune recognition.

Indoor Chemistry: Materials, Ventilation Systems, and Occupant Activities

Energy Technology Data Exchange (ETDEWEB)

Morrison, G.C.; Corsi, R.L.; Destaillats, H.; Nazaroff, W.W.; Wells, J.R.

2006-05-01

Chemical processes taking place in indoor environments can significantly alter the nature and concentrations of pollutants. Exposure to secondary contaminants generated in these reactions needs to be evaluated in association with many aspects of buildings to minimize their impact on occupant health and well-being. Focusing on indoor ozone chemistry, we describe alternatives for improving indoor air quality by controlling chemical changes related to building materials, ventilation systems, and occupant activities.

Alternative methods for determination of composition and porosity in abradable materials

International Nuclear Information System (INIS)

Matejicek, Jiri; Kolman, Blahoslav; Dubsky, Jiri; Neufuss, Karel; Hopkins, Noel; Zwick, Jochen

2006-01-01

Materials properties and performance are governed by their composition and structure. These are commonly characterized using materialography and image analysis. However, in abradable materials, obtaining a reliable and representative sample (polished section) for this widespread technique is complicated by their abradable nature and heterogeneity. Therefore, alternative methods are also considered in this paper. They are namely X-ray diffraction and electron probe microanalysis to determine the composition, and mercury intrusion porosimetry, Archimedean porosimetry and helium pycnometry to determine the porosity. These methods, including materialography, were applied on representative abradable materials produced by plasma spraying; their results are compared and the advantages and drawbacks of each method are discussed

Assateague Island National Seashore alternative transportation systems planning study and business plan for alternative transportation

Science.gov (United States)

2012-08-31

The purpose of this study was to (1) study the potential expansion of existing alternative transportation systems (bicycle facilities) and development of new alternative transportation systems in and around the Maryland District of Assateague Island ...

Systems analysis and simulation of fissile materials disposition alternatives

International Nuclear Information System (INIS)

Farish, T.J.; Farmen, R.F.; Boerigter, S.T.; DeMuth, N.S.

1996-01-01

A detailed process flow model has been developed for use in the Fissile Materials Disposition program. The model calculates fissile material flows and inventories among the various processing and storage facilities over the life of the disposition program. Given existing inventories and schedules for processing, we can estimate the required size of processing and storage facilities, including equipment requirements, plant floorspace, approximate costs, and surge capacities. The model was designed to allow rapid prototyping, parallel and team development of facility and sub-facility models, consistent levels of detail and the use of a library of generic objects representing unit process operations

Seal design alternatives study

International Nuclear Information System (INIS)

Van Sambeek, L.L.; Luo, D.D.; Lin, M.S.; Ostrowski, W.; Oyenuga, D.

1993-06-01

This report presents the results from a study of various sealing alternatives for the WIPP sealing system. Overall, the sealing system has the purpose of reducing to the extent possible the potential for fluids (either gas or liquid) from entering or leaving the repository. The sealing system is divided into three subsystems: drift and panel seals within the repository horizon, shaft seals in each of the four shafts, and borehole seals. Alternatives to the baseline configuration for the WIPP seal system design included evaluating different geometries and schedules for seal component installations and the use of different materials for seal components. Order-of-magnitude costs for the various alternatives were prepared as part of the study. Firm recommendations are not presented, but the advantages and disadvantages of the alternatives are discussed. Technical information deficiencies are identified and studies are outlined which can provide required information

Material Systems

DEFF Research Database (Denmark)

Jensen, Mads Brath; Mortensen, Henrik Rubæk; Mullins, Michael

2009-01-01

This paper describes and reflects upon the results of an investigative project which explores the setting up of a material system - a parametric and generative assembly consisting of and taking into consideration material properties, manufacturing constraints and geometric behavior. The project...... approaches the subject through the construction of a logic-driven system aiming to explore the possibilities of a material system that fulfills spatial, structural and performative requirements concurrently and how these are negotiated in situations where they might be conflicting....

Conceptual design report: Nuclear materials storage facility renovation. Part 6, Alternatives study

International Nuclear Information System (INIS)

1995-01-01

The Nuclear Materials Storage Facility (NMSF) at the Los Alamos National Laboratory (LANL) was a Fiscal Year (FY) 1984 line-item project completed in 1987 that has never been operated because of major design and construction deficiencies. This renovation project, which will correct those deficiencies and allow operation of the facility, is proposed as an FY 97 line item. The mission of the project is to provide centralized intermediate and long-term storage of special nuclear materials (SNM) associated with defined LANL programmatic missions and to establish a centralized SNM shipping and receiving location for Technical Area (TA)-55 at LANL. Based on current projections, existing storage space for SNM at other locations at LANL will be loaded to capacity by approximately 2002. This will adversely affect LANUs ability to meet its mission requirements in the future. The affected missions include LANL's weapons research, development, and testing (WRD ampersand T) program; special materials recovery; stockpile survelliance/evaluation; advanced fuels and heat sources development and production; and safe, secure storage of existing nuclear materials inventories. The problem is further exacerbated by LANL's inability to ship any materials offsite because of the lack of receiver sites for material and regulatory issues. Correction of the current deficiencies and enhancement of the facility will provide centralized storage close to a nuclear materials processing facility. The project will enable long-term, cost-effective storage in a secure environment with reduced radiation exposure to workers, and eliminate potential exposures to the public. This report is organized according to the sections and subsections outlined by Attachment 111-2 of DOE Document AL 4700.1, Project Management System. It is organized into seven parts. This document, Part VI - Alternatives Study, presents a study of the different storage/containment options considered for NMSF

17 CFR 242.302 - Recordkeeping requirements for alternative trading systems.

Science.gov (United States)

2010-04-01

... alternative trading systems. 242.302 Section 242.302 Commodity and Securities Exchanges SECURITIES AND... SECURITY FUTURES Regulation Ats-Alternative Trading Systems § 242.302 Recordkeeping requirements for alternative trading systems. To comply with the condition set forth in paragraph (b)(8) of § 242.301, an...

Alternative buffer material. Status of the ongoing laboratory investigation of reference materials and test package 1

International Nuclear Information System (INIS)

Svensson, Daniel; Dueck, Ann; Nilsson, Ulf; Olsson, Siv; Sanden, Torbjoern; Lydmark, Sara; Jaegerwall, Sara; Pedersen, Karsten; Hansen, Staffan

2011-07-01

Bentonite clay is part of the Swedish KBS-3 design of final repositories for high level radioactive waste. Wyoming bentonite with the commercial name MX-80 (American Colloid Co) has long been the reference for buffer material in the KBS-3 concept. Extending the knowledge base of alternative buffer materials will make it possible to optimize regarding safety, availability and cost. For this reason the field experiment Alternative Buffer Material (ABM) was started at Aespoe Hard Rock Laboratory during 2006. The experiment includes three medium-scale test packages, each consisting of a central steel tube with heaters, and a buffer of compacted clay. Eleven different clays were chosen for the buffers to examine effects of smectite content, interlayer cations and overall iron content. Also bentonite pellets with and without additional quartz are being tested. The buffer in package 1 had been subjected to wetting by formation water and heating for more than two years (at 130 deg C for ∼ 1 year) when it was retrieved and analyzed. The main purposes of the project were to characterise the clays with respect to hydro-mechanical properties, mineralogy and chemical composition and to identify any differences in behaviour or long term stability. The diversity of clays and the heater of steel also make the experiment suitable for studies of iron-bentonite interactions. This report concerns the work accomplished up to now and is not to be treated as any final report of the project

Alternative buffer material. Status of the ongoing laboratory investigation of reference materials and test package 1

Energy Technology Data Exchange (ETDEWEB)

Svensson, Daniel [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Dueck, Ann; Nilsson, Ulf; Olsson, Siv; Sanden, Torbjoern [Clay Technology AB, Lund (Sweden); Lydmark, Sara; Jaegerwall, Sara; Pedersen, Karsten [Microbial Analytics Sweden AB, Moelnlycke (Sweden); Hansen, Staffan [LTH Lund Univ., Lund (Sweden)

2011-07-15

Bentonite clay is part of the Swedish KBS-3 design of final repositories for high level radioactive waste. Wyoming bentonite with the commercial name MX-80 (American Colloid Co) has long been the reference for buffer material in the KBS-3 concept. Extending the knowledge base of alternative buffer materials will make it possible to optimize regarding safety, availability and cost. For this reason the field experiment Alternative Buffer Material (ABM) was started at Aespoe Hard Rock Laboratory during 2006. The experiment includes three medium-scale test packages, each consisting of a central steel tube with heaters, and a buffer of compacted clay. Eleven different clays were chosen for the buffers to examine effects of smectite content, interlayer cations and overall iron content. Also bentonite pellets with and without additional quartz are being tested. The buffer in package 1 had been subjected to wetting by formation water and heating for more than two years (at 130 deg C for {approx} 1 year) when it was retrieved and analyzed. The main purposes of the project were to characterise the clays with respect to hydro-mechanical properties, mineralogy and chemical composition and to identify any differences in behaviour or long term stability. The diversity of clays and the heater of steel also make the experiment suitable for studies of iron-bentonite interactions. This report concerns the work accomplished up to now and is not to be treated as any final report of the project.

Assessment on the sustainable use of alternative construction materials as a substitute to natural aggregates

CSIR Research Space (South Africa)

George, Theresa B

2016-08-01

Full Text Available , and identifies potential construction materials such as glass, slags and recycled asphalt pavement (RAP) that are locally available as alternative aggregate materials to virgin aggregates. An economic cost analysis conducted indicated that it is more cost...

Alternatives of Cross-Border Securities Settlement System in East Asia

Directory of Open Access Journals (Sweden)

Hee-Yul Chai

2005-12-01

Full Text Available The establishment of cross-border securities settlement system is a very important element of regional capital market integration. Despite its importance, relatively few arguments, both theoretical and practical, have been advanced on the subject. This paper aims to examine the alternatives of cross-border securities settlement system in East Asia, and analyse the feasibility and the advantages and disadvantages of each alternative. The paper underlines the need to develop a multi-currency DVP securities settlement system. The conceivable alternatives of East Asia's cross-border securities settlement system can be divided into decentralized system and centralized system. It is possible to consider a large array of institutional settings according to the depository/settlement methods. The comparison of the alternatives is based on economic efficiency, feasibility and institutional location of settlement system. In view of these criteria, it is argued that a 'big-bang' approach toward imperfectly cenralized system is the most desirable alternative.

Selective confinement of vibrations in composite systems with alternate quasi-regular sequences

International Nuclear Information System (INIS)

Montalban, A.; Velasco, V.R.; Tutor, J.; Fernandez-Velicia, F.J.

2007-01-01

We have studied the atom displacements and the vibrational frequencies of 1D systems formed by combinations of Fibonacci, Thue-Morse and Rudin-Shapiro quasi-regular stacks and their alternate ones. The materials are described by nearest-neighbor force constants and the corresponding atom masses, particularized to the Al, Ag systems. These structures exhibit differences in the frequency spectrum as compared to the original simple quasi-regular generations but the most important feature is the presence of separate confinement of the atom displacements in one of the sequences forming the total composite structure for different frequency ranges

Selective confinement of vibrations in composite systems with alternate quasi-regular sequences

Energy Technology Data Exchange (ETDEWEB)

Montalban, A. [Departamento de Ciencia y Tecnologia de Materiales, Division de Optica, Universidad Miguel Hernandez, 03202 Elche (Spain); Velasco, V.R. [Instituto de Ciencia de Materiales de Madrid, CSIC, Sor Juana Ines de la Cruz 3, 28049 Madrid (Spain)]. E-mail: vrvr@icmm.csic.es; Tutor, J. [Departamento de Fisica Aplicada, Universidad Autonoma de Madrid, Cantoblanco, 28049 Madrid (Spain); Fernandez-Velicia, F.J. [Departamento de Fisica de los Materiales, Facultad de Ciencias, Universidad Nacional de Educacion a Distancia, Senda del Rey 9, 28080 Madrid (Spain)

2007-01-01

We have studied the atom displacements and the vibrational frequencies of 1D systems formed by combinations of Fibonacci, Thue-Morse and Rudin-Shapiro quasi-regular stacks and their alternate ones. The materials are described by nearest-neighbor force constants and the corresponding atom masses, particularized to the Al, Ag systems. These structures exhibit differences in the frequency spectrum as compared to the original simple quasi-regular generations but the most important feature is the presence of separate confinement of the atom displacements in one of the sequences forming the total composite structure for different frequency ranges.

Public concerns and alternative nuclear power systems

International Nuclear Information System (INIS)

Mayo, L.H.

1980-02-01

The basic task undertaken in this study was to assess the relative public acceptability of three general types of nuclear power systems as alternatives to the existing Light Water Reactor (LWR) system. Concerns registered toward nuclear power constituted the basic data for this assessment. The primary measure adopted for determining the significance of concerns was the degree of difficulty posed by the concern to the nuclear power decisional structure in the establishment and maintenance of norms to control risks or to advance intended energy objectives. Alleviations or exacerbations of concern resulting from particular attributes of alternative systems were measured from an LWR baseline

Project on Alternative Systems Study - PASS. Final report

International Nuclear Information System (INIS)

1992-10-01

Alternative repository systems for deep disposal of spent fuel and different types of canisters are studied regarding technical aspects in Project on Alternative System Study (PASS). The objective is to present a ranking of repository systems as well as of canister types for each system. The studies and compared systems are: KBS-3, Medium Long Tunnels (MLH), Long tunnels (VLH) and Deep Boreholes (VDH). For KBS-3 and MLH five canister types are compared (copper/steel, copper/lead, copper (HIP), steel/lead and steel), for VLH two types (copper/steel and steel), and for VDH three types (titanium/concrete with non-consolidated fuel assemblies, titanium/concrete with consolidated assemblies and copper (HIP) with non-consolidated assemblies). The comparison is separated into three sub-comparisons (Technology, Long-term performance and safety, and Costs), which eventually are merged into one ranking. With respect to canister alternatives the result is that the copper/steel canister is ranked first for KBS-3, MLH and VLH, while the titanium/concrete canister is ranked first for VDH (non-consolidated as well as consolidated assemblies. With these canister alternatives the merged ranking of repository systems results in placing KBS-3 slightly in front of MLH. VLH comes thereafter and VDH last. (32 refs.)

Pineapple leaf fiber as reinforce in composite materials, an alternative for automotive industry

International Nuclear Information System (INIS)

Campos, Rejane Daniela de; Seo, Emilia Satoshi Miyamaru

2013-01-01

The composites appear as an extremely favorable alternative for different industries, due to the fact that it combines the best mechanical properties with the best physic-chemical properties of two or more materials. Nowadays, in the evaluation of materials, besides criteria such as economic viability and performance, the environmental criterion was included in this evaluation. Part of the environmental criteria is the use of biodegradable materials and/or recycled materials. In this sense, researches focused on vegetal fibers, as reinforcement in composites are growing considerably and positive results for its performance were achieved. Moreover, the environmental-friendly approach not only is the unique advantage on usage of vegetal fibers, but also it has an economical advantage, because of the low cost and good performance due to low density. The fiber extracted from the pineapple leaf (PALF) is a new alternative for automotive industry as cellulose-based fiber composite. In this sense, the present paper aims to present the characterization of the pineapple leaf fiber for manufacturing the automotive composite materials. Milled pineapple fibers extracted, in two different ways and submitted to mercerisation treatments, were characterized by mechanical and thermal properties; density; morphology; FTIR spectroscopy, EDX and X-ray diffraction. It is important to characterize the fibers, in order to obtain appropriate mechanical properties of composite. (author)

Pineapple leaf fiber as reinforce in composite materials, an alternative for automotive industry

Energy Technology Data Exchange (ETDEWEB)

Campos, Rejane Daniela de; Seo, Emilia Satoshi Miyamaru, E-mail: rejanedaniela@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2013-07-01

The composites appear as an extremely favorable alternative for different industries, due to the fact that it combines the best mechanical properties with the best physic-chemical properties of two or more materials. Nowadays, in the evaluation of materials, besides criteria such as economic viability and performance, the environmental criterion was included in this evaluation. Part of the environmental criteria is the use of biodegradable materials and/or recycled materials. In this sense, researches focused on vegetal fibers, as reinforcement in composites are growing considerably and positive results for its performance were achieved. Moreover, the environmental-friendly approach not only is the unique advantage on usage of vegetal fibers, but also it has an economical advantage, because of the low cost and good performance due to low density. The fiber extracted from the pineapple leaf (PALF) is a new alternative for automotive industry as cellulose-based fiber composite. In this sense, the present paper aims to present the characterization of the pineapple leaf fiber for manufacturing the automotive composite materials. Milled pineapple fibers extracted, in two different ways and submitted to mercerisation treatments, were characterized by mechanical and thermal properties; density; morphology; FTIR spectroscopy, EDX and X-ray diffraction. It is important to characterize the fibers, in order to obtain appropriate mechanical properties of composite. (author)

Advanced physical protection systems for nuclear materials

International Nuclear Information System (INIS)

Jones, O.E.

1976-01-01

Because of the increasing incidence of terrorism, there is growing concern that nuclear materials and facilities need improved physical protection against theft, diversion, or sabotage. Physical protection systems for facilities or transportation which have balanced effectiveness include information systems, access denial systems, adequate and timely response, recovery capability, and use denial methods for despoiling special nuclear materials (SNM). The role of these elements in reducing societal risk is described; however, it is noted that, similar to nuclear war, the absolute risks of nuclear theft and sabotage are basically unquantifiable. Sandia Laboratories has a major US Energy Research and Development Administration (ERDA) role in developing advanced physical protection systems for improving the security of both SNM and facilities. These activities are surveyed in this paper. A computer simulation model is being developed to assess the cost-effectiveness of alternative physical protection systems under various levels of threat. Improved physical protection equipment such as perimeter and interior alarms, secure portals, and fixed and remotely activated barriers is being developed and tested. In addition, complete prototype protection systems are being developed for representative nuclear facilities. An example is shown for a plutonium storage vault. The ERDA safe-secure transportation system for highway shipments of all significant quantities of government-owned SNM is described. Adversary simulation as a tool for testing and evaluating physical protection systems is discussed. Finally, a list of measures is given for assessing overall physical protection system performance. (author)

Advanced physical protection systems for nuclear materials

International Nuclear Information System (INIS)

Jones, O.E.

1975-10-01

Because of the increasing incidence of terrorism, there is growing concern that nuclear materials and facilities need improved physical protection against theft, diversion, or sabotage. Physical protection systems for facilities or transportation which have balanced effectiveness include information systems, access denial systems, adequate and timely response, recovery capability, and use denial methods for despoiling special nuclear materials (SNM). The role of these elements in reducing societal risk is described; however, it is noted that, similar to nuclear war, the absolute risks of nuclear theft and sabotage are basically unquantifiable. Sandia Laboratories has a major Energy Research and Development Administration (ERDA) role in developing advanced physical protection systems for improving the security of both SNM and facilities. These activities are surveyed. A computer simulation model is being developed to assess the cost-effectiveness of alternative physical protection systems under various levels of threat. Improved physical protection equipment such as perimeter and interior alarms, secure portals, and fixed and remotely-activated barriers is being developed and tested. In addition, complete prototype protection systems are being developed for representative nuclear facilities. An example is shown for a plutonium storage vault. The ERDA safe-secure transportation system for highway shipments of all significant quantities of government-owned SNM is described. Adversary simulation as a tool for testing and evaluating physical protection systems is discussed. A list of measures is given for assessing overall physical protection system performance. (auth)

Eco-Friendly Alternative Refrigeration Systems

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 6; Issue 10. Eco-Friendly Alternative Refrigeration Systems - Magnetic and ... Author Affiliations. S S Verma1. Deptartment of Physics, Sant Longowal Institute of Engineering and Technology Longowal, District Sangrur, Punjab 148 106, India.

Evaluation of Alternative Refractory Materials for the Main Flame Deflectors at KSC Launch Complexes

Science.gov (United States)

Calle, Luz Marina; Trejo, David; Rutkowsky, Justin

2006-01-01

The deterioration of the refractory materials used to protect the KSC launch complex steel base structures from the high temperatures during launches results in frequent and costly repairs and safety hazards. KSC-SPEC-P-0012, Specification for Refractory Concrete, is ineffective in qualifying refractory materials. This study of the specification and of alternative refractory materials recommends a complete revision of the specification and further investigation of materials that were found to withstand the environment of the Solid Rocket Booster main flame deflector better than the refractory materials in current use in terms of compressive strength, tensile strength, modulus of rupture, shrinkage, and abrasion.

Mesoporous TiO2 : an alternative material for PEM fuel cells catalyst support

Energy Technology Data Exchange (ETDEWEB)

Do, T.B. [Michigan Univ., Ann Arbor, MI (United States). Dept. of Materials Science; Ruthkosky, M.; Cai, M. [General Motors, Warren, MI (United States). Research and Development Center

2008-07-01

This paper discussed the feasibility of using an alternative catalyst support material to replace carbon in proton exchange membrane (PEM) fuel cells. The alternative catalyst support material requires a high surface area with a large porosity but must have comparable conductivity with carbon. A mesoporous titanium oxide (TiO2) material produced by coprecipitation was introduced. The conductivity of the material is about one order of that of carbon. The 8 mole per cent Nb-doped TiO2 was formed and deposited on the surface of a nano polystyrene (PS) template via the hydrolysis of a co-solution of Ti(OC4H9)4 and Nb(OC2H5)5. The removal of PS by heat treatment produced porous structure of TiO2 with the appearance of 3 different pore types, notably open pore, ink-pot pores and closed pores. TiO2 formed from the rutile phase, allowing a lower activation temperature at 850 degrees C in a hydrogen atmosphere. The pore structures were retained after this heat treatment. The BET surface area was 116 m{sup 2}/g, porosity was 22 per cent and the average pore size was 159 angstrom. The conductivity improved considerably from almost non-conductive to one order of that of carbon.

Systems impacts of spent fuel disassembly alternatives

International Nuclear Information System (INIS)

1984-07-01

Three studies were completed to evaluate four alternatives to the disposal of intact spent fuel assemblies in a geologic repository. A preferred spent fuel waste form for disposal was recommended on consideration of (1) package design and fuel/package interaction, (2) long-term, in-repository performance of the waste form, and (3) overall process performance and costs for packaging, handling, and emplacement. The four basic alternative waste forms considered were (1) end fitting removal, (2) fission gas venting, (3) disassembly and close packing, and (4) shearing/immobilization. None of the findings ruled out any alternative on the basis of waste package considerations or long-term performance of the waste form. The third alternative offers flexibility in loading that may prove attractive in the various geologic media under consideration, greatly reduces the number of packages, and has the lowest unit cost. These studies were completed in October, 1981. Since then Westinghouse Electric Corporation and the Office of Nuclear Waste Isolation have completed studies in related fields. This report is now being published to provide publicly the background material that is contained within. 47 references, 28 figures, 31 tables

A cost-benefit analysis for materials management information systems.

Science.gov (United States)

Slapak-Iacobelli, L; Wilde, A H

1993-02-01

The cost-benefit analysis provided the system planners with valuable information that served many purposes. It answered the following questions: Why was the CCF undertaking this project? What were the alternatives? How much was it going to cost? And what was the expected outcome? The process of developing cost-benefit the document kept the project team focused. It also motivated them to involve additional individuals from materials management and accounts payable in its development. A byproduct of this involvement was buy-in and commitment to the project by everyone in these areas. Consequently, the project became a team effort championed by many and not just one. We were also able to introduce two new information system processes: 1) a management review process with goals and anticipated results, and 2) a quality assurance process that ensured the CCF had a better product in the end. The cost-benefit analysis provided a planning tool that assisted in successful implementation of an integrated materials management information system.

Electric vehicles batteries thermal management systems employing phase change materials

Science.gov (United States)

Ianniciello, Lucia; Biwolé, Pascal Henry; Achard, Patrick

2018-02-01

Battery thermal management is necessary for electric vehicles (EVs), especially for Li-ion batteries, due to the heat dissipation effects on those batteries. Usually, air or coolant circuits are employed as thermal management systems in Li-ion batteries. However, those systems are expensive in terms of investment and operating costs. Phase change materials (PCMs) may represent an alternative which could be cheaper and easier to operate. In fact, PCMs can be used as passive or semi-passive systems, enabling the global system to sustain near-autonomous operations. This article presents the previous developments introducing PCMs for EVs battery cooling. Different systems are reviewed and solutions are proposed to enhance PCMs efficiency in those systems.

17 CFR 242.303 - Record preservation requirements for alternative trading systems.

Science.gov (United States)

2010-04-01

... requirements for alternative trading systems. 242.303 Section 242.303 Commodity and Securities Exchanges... REQUIREMENTS FOR SECURITY FUTURES Regulation Ats-Alternative Trading Systems § 242.303 Record preservation requirements for alternative trading systems. (a) To comply with the condition set forth in paragraph (b)(9) of...

Alternative energy sources or integrated alternative energy systems? Oil as a modern lance of Peleus for the energy transition

International Nuclear Information System (INIS)

Szklo, Alexandre; Schaeffer, Roberto

2006-01-01

In this viewpoint, we discuss the importance of consorting alternative energy sources with oil, and not of opposing them. That is why we introduce the concept of alternative energy systems, which we feel is broader-ranging and more effective than alternative energy sources, as this deals with the actual transformation process of the global energy system. Alternative energy systems integrate oil with other energy sources and pave the way for new systems, which will benefit from what we call the 'virtues of oil'. They produce energy carriers for multi-fuel and multi-product strategies, where flexibility is a key target, allied to other co-benefits, especially those related to the increased use of renewable energy sources. The concept of alternative energy systems can bring a new light to the oil transition era discussion and might also influence energy policies for promoting renewables

Construction projects using alternative materials: a framework to assess their sustainability.

OpenAIRE

Fevre-Gautier , Anne-Lise; Beylot , Antoine; Vaxelaire , Stéphane; Michel , Pascale; Brullot , Sabrina; Lannou , Grégory; Stoos , Marion

2012-01-01

The increasing use of alternative materials and local solutions for construction projects raises questions about success conditions and criteria for the economic feasibility and global sustainability of such projects. Among others, how can design conditions - especially regarding the decision process - determine their success? We will present the results of a two-years project conducted from February 2010 to March 2012 in collaboration with ADEME (French agency of environment and energy contr...

Nanocomposite Materials of Alternately Stacked C60 Monolayer and Graphene

International Nuclear Information System (INIS)

Ishikawa, M.; Miura, K.; Kamiya, S.; Yoshimoto, S.; Suzuki, M.; Kuwahara, D.; Sasaki, N.

2010-01-01

We synthesized the novel nanocomposite consisting alternately of a stacked single graphene sheet and a C 60 monolayer by using the graphite intercalation technique in which alkylamine molecules help intercalate large C 60 molecules into the graphite. Moreover, it is found that the intercalated C 60 molecules can rotate in between single graphene sheets by using C 13 NMR measurements. This preparation method provides a general way for intercalating huge fullerene molecules into graphite, which will lead to promising materials with novel mechanical, physical, and electrical properties.

Identification of approximately duplicate material records in ERP systems

Science.gov (United States)

Zong, Wei; Wu, Feng; Chu, Lap-Keung; Sculli, Domenic

2017-03-01

The quality of master data is crucial for the accurate functioning of the various modules of an enterprise resource planning (ERP) system. This study addresses specific data problems arising from the generation of approximately duplicate material records in ERP databases. Such problems are mainly due to the firm's lack of unique and global identifiers for the material records, and to the arbitrary assignment of alternative names for the same material by various users. Traditional duplicate detection methods are ineffective in identifying such approximately duplicate material records because these methods typically rely on string comparisons of each field. To address this problem, a machine learning-based framework is developed to recognise semantic similarity between strings and to further identify and reunify approximately duplicate material records - a process referred to as de-duplication in this article. First, the keywords of the material records are extracted to form vectors of discriminating words. Second, a machine learning method using a probabilistic neural network is applied to determine the semantic similarity between these material records. The approach was evaluated using data from a real case study. The test results indicate that the proposed method outperforms traditional algorithms in identifying approximately duplicate material records.

An Alternative Front End Analysis Strategy for Complex Systems

Science.gov (United States)

2014-12-01

missile ( ABM ) system . Patriot is employed in the field through a battalion echelon organizational structure. The line battery is the basic building...Research Report 1981 An Alternative Front End Analysis Strategy for Complex Systems M. Glenn Cobb U.S. Army Research Institute...NUMBER W5J9CQ11D0003 An Alternative Front End Analysis Strategy for Complex Systems 5b. PROGRAM ELEMENT NUMBER 633007 6

Alternative materials for the reinforcement and prestressing of concrete

National Research Council Canada - National Science Library

Clarke, John L

1993-01-01

... and bridges subjected to de-icing salts. Many approaches are being tried to inhibit the corrosion mechanism in aggressive environments. Most involve protective systems of some sort, applied either to the reinforcement directly or to the exposed concrete surface. One alternative approach being developed worldwide at an increasing pace is the replacement of...

Nanocomposite Materials of Alternately Stacked C60 Monolayer and Graphene

Directory of Open Access Journals (Sweden)

Makoto Ishikawa

2010-01-01

Full Text Available We synthesized the novel nanocomposite consisting alternately of a stacked single graphene sheet and a C60 monolayer by using the graphite intercalation technique in which alkylamine molecules help intercalate large C60 molecules into the graphite. Moreover, it is found that the intercalated C60 molecules can rotate in between single graphene sheets by using C13 NMR measurements. This preparation method provides a general way for intercalating huge fullerene molecules into graphite, which will lead to promising materials with novel mechanical, physical, and electrical properties.

Alternative Grading Systems. The Practitioner, Vol. III, No. 3.

Science.gov (United States)

De Leonibus, Nancy; Thomson, Scott

After examining some of the pros and cons of traditional grading, the demands colleges make on grading practices, and the responses of people interested in grading, a number of examples of operating alternative systems are given. The alternatives include a dual (pass/withdraw grading in some courses, traditional grading in others) system, a…

Evaluation of the physical properties of an endodontic Portland cement incorporating alternative radiopacifiers used as root-end filling material.

Science.gov (United States)

Camilleri, J

2010-03-01

To investigate the physical and chemical properties of Portland cement (PC) loaded with alternative radiopacifying materials for use as root-end filling materials in a mineral trioxide aggregate (MTA)-like system. Portland cement loaded with barium sulphate, gold and silver/tin alloy was mixed with water, and the physical and chemical properties of the hydrated cements were evaluated. MTA and intermediate restorative material (IRM) were used as controls. The radiopacity was compared to the equivalent thickness of aluminium, and the setting time of the cements was assessed using an indentation technique. The compressive strength and the stress-strain relationship were determined at 28 days. The stress-strain relationship was determined by monitoring the strain generated when the cement was subjected to compressive load. In addition, the pH was determined in water and simulated body fluid for a period of 28 days. The radiopacity of the cements using alternative radiopacifiers was comparable to MTA (P > 0.05). IRM demonstrated a higher radiopacity than all the materials tested (P cements with the exception of IRM exhibited an alkaline pH and had an extended setting time when compared to IRM. MTA had a longer setting time than the PC (P cement (P = 0.159). The addition of a radiopacifier retarded the setting time (P cements had comparable strength to PC (P > 0.05). IRM was the weakest cement tested (P cement loaded with gold radiopacifier had comparable strength to MTA (P = 1). The stress-strain relationship was linear for all the cements with IRM generating more strain on loading. Within the parameters set in this study, bismuth oxide in MTA can be replaced by gold or silver/tin alloy. The physical, mechanical and chemical properties of the cement replaced with alternative radiopacifiers were similar and comparable to ProRoot MTA.

Alternative approaches of SiC & related wide bandgap materials in light emitting & solar cell applications

Science.gov (United States)

Wellmann, Peter; Syväjärvi, Mikael; Ou, Haiyan

2014-03-01

understanding the device performance. In relation to these, the surface pre-treatment and deposition technique can influence the reliability and electric field durability of the system, and relate to interface and near interface regions between the dielectric and semiconductor which can host electronic defects which change the surface potential, reduces mobility and enhance the recombination of charge carriers. At the end, materials for energy savings are critically needed. At the symposium ''Alternative approaches of SiC and related wide bandgap materials in light emitting and solar cell applications'', held at the E-MRS 2013 Spring meeting, 27-31 May, 2013 Strasbourg, France, a variety of concepts were presented. In this publication, a selection is presented that represents a range of issues from materials to reliability processing to system approaches. Acknowledgements: Technical support during preparation of the symposium program and proceedings by Saskia Schimmel is greatly acknowledged.

A computerized system based on an alternative pulse echo immersion technique for acoustic characterization of non-porous solid tissue mimicking materials

Science.gov (United States)

Nazihah Mat Daud, Anis; Jaafar, Rosly; Kadri Ayop, Shahrul; Supar Rohani, Md

2018-04-01

This paper discusses the development of a computerized acoustic characterization system of non-porous solid tissue mimicking materials. This system employs an alternative pulse echo immersion technique and consists of a pulser/receiver generator, a transducer used as both a transmitter and a receiver, a digital oscilloscope, and a personal computer with a custom-developed program installed. The program was developed on the LabVIEW 2012 platform and comprises two main components, a user interface and a block diagram. The user interface consists of three panels: a signal acquisition and selection panel, a display panel, and a calculation panel. The block diagram comprises four blocks: a signal acquisition block, a peak signal analysis block, an acoustic properties calculation and display block, and an additional block. Interestingly, the system can be operated in both online and offline modes. For the online mode, the measurements are performed by connecting the system with a Rigol DS2000 Series digital oscilloscope. In contrast, the measurements are carried out by processing the saved data on the computer for the offline mode. The accuracy and consistency of the developed system was validated by a KB-Aerotech Alpha Series transducer with 5 MHz center frequency and a Rigol DS2202 two-channel 200 MHz 2 GSa s-1 digital oscilloscope, based on the measurement of the acoustic properties of three poly(methyl methacrylate) samples immersed in a medium at a temperature of (24.0  ±  0.1) °C. The findings indicated that the accuracy and consistency of the developed system was exceptionally high, within a 1.04% margin of error compared to the reference values. As such, this computerized system can be efficiently used for the acoustic characterization of non-porous solid tissues, given its spontaneous display of results, user-friendly interface, and convenient hardware connection.

Alternative breeder and near-breeder systems

International Nuclear Information System (INIS)

Critoph, E.

1983-01-01

Nuclear power reactor systems have been developed over the last three decades to the point where they are economically competitive, safe and reliable sources of electrical energy. However, with our present knowledge of fissile resources, there is no assurance that the commercially proven reactor systems, using their current fuel cycles, could play a major role in supplying the total world energy needs of the next, and subsequent, centuries. There is a wide consensus that such assurance requires development of reactor systems with very significantly improved fuel resource utilization. The best known of these, and the one currently receiving the lion's share of attention and effort, is the fast breeder reactor (FBR). This paper reviews the characteristics, development status and planned programmes for alternative concepts to the FBR that meet the requirement for large improvement in fuel resource utilization, i.e. alternative breeder and near-breeder systems. These include: heavy-water reactors operating on thorium fuel cycles, light-water high-conversion and breeder reactors, high-temperature gas-cooled reactors operating on thorium fuel cycles, molten salt reactors and heavy-water suspension reactors. Any attempt to make a logical choice for exploitation among these various alternatives involves a consideration of the interplay between reactor system characteristics on the one hand and a forecast of political and economic environments on the other. The reactor breeding (or conversion) ratio has received a great deal of emphasis, but an optimum choice depends also on a consideration of several other factors, including out- and in-reactor specific fuel inventories, fuel fabrication and reprocessing costs, reactor capital cost and load factor, fuel resources and demand growth rate of capacity. Possible variations in this optimum choice with time and regional location are discussed

Selection of an Alternate Biocide for the ISS Internal Thermal Control System Coolant, Phase 2

Science.gov (United States)

Wilson, Mark E.; Cole, Harold; Weir, Natalee; Oehler, Bill; Steele, John; Varsik, Jerry; Lukens, Clark

2004-01-01

The ISS (International Space Station) ITCS (Internal Thermal Control System) includes two internal coolant loops that utilize an aqueous based coolant for heat transfer. A silver salt biocide had previously been utilized as an additive in the coolant formulation to control the growth and proliferation of microorganisms within the coolant loops. Ground-based and in-flight testing demonstrated that the silver salt was rapidly depleted, and did not act as an effective long-term biocide. Efforts to select an optimal alternate biocide for the ITCS coolant application have been underway and are now in the final stages. An extensive evaluation of biocides was conducted to down-select to several candidates for test trials and was reported on previously. Criteria for that down-select included: the need for safe, non-intrusive implementation and operation in a functioning system; the ability to control existing planktonic and biofilm residing microorganisms; a negligible impact on system-wetted materials of construction; and a negligible reactivity with existing coolant additives. Candidate testing to provide data for the selection of an optimal alternate biocide is now in the final stages. That testing has included rapid biocide effectiveness screening using Biolog MT2 plates to determine minimum inhibitory concentration (amount that will inhibit visible growth of microorganisms), time kill studies to determine the exposure time required to completely eliminate organism growth, materials compatibility exposure evaluations, coolant compatibility studies, and bench-top simulated coolant testing. This paper reports the current status of the effort to select an alternate biocide for the ISS ITCS coolant. The results of various test results to select the optimal candidate are presented.

Development of a dual ion beam system with single accelerator for materials studies

International Nuclear Information System (INIS)

Suzuki, Kazumichi; Nishimura, Eiichi; Hashimoto, Tsuneyuki

1986-01-01

The dual ion beam accelerator system has been developed for simulation studies of neutron radiation damage of structural materials for nuclear fusion and fission reactors. One accelerator is used to accelerate two different kinds of ions, which are generated in the ion source simultaneously. One of these ions is selected alternatively by switching the magnetic field of the analyzing magnet, and is then accelerated to the desired energy value. The system is controlled by a microcomputer. The accelerator used in the system is a conventional 400 kV Cockcroft-Walton accelerator. The performance test by the acceleration of He + and Ar + shows that the system is capable of accelerating two ions alternatively with a switching time of less than 22 s. The beam current obtained with the microcomputer control is more than 98% of the current obtained by manual operation. (orig.)

Energy Conversion Alternatives Study (ECAS), Westinghouse phase 1. Volume 2: Materials considerations. [materials used in boilers and heat exchangers of energy conversion systems for electric power plants using coal

Science.gov (United States)

Thomas, D. E.

1976-01-01

Extensive studies are presented which were carried out on materials behavior in nine advanced energy conversion systems employing coal and coal-derived fuels. The areas of materials behavior receiving particular attention in this regard are: (1) fireside corrosion and erosion in boiler and heat exchanger materials, (2) oxidation and hot corrosion of gas turbine materials, (3) liquid metal corrosion and mass transport, (4) high temperature steam corrosion, (5) compatability of materials with coal slag and MHD seed, (6) reaction of materials with impure helium, (7) allowable stresses for boiler and heat exchanger materials, (8) environmental effects on mechanical properties, and (9) liquid metal purity control and instrumentation. Such information was then utilized in recommending materials for use in the critical components of the power systems, and at the same time to identify materials problem areas and to evaluate qualitatively the difficulty of solving those problems. Specific materials recommendations for critical components of the nine advanced systems under study are contained in summary tables.

Alternative electrical transmission systems and their environmental impact

Energy Technology Data Exchange (ETDEWEB)

Schiefelbein, G.F.

1977-08-01

A general description is provided of electrical transmission systems as an aid in determining their environmental impacts. Alternating current, direct current, overhead systems, underground systems, and water crossings are treated. The cost, performance, reliability, safety, and environmental impact of these systems are compared.

Alternative Genres in Information Systems Research

DEFF Research Database (Denmark)

Avital, Michel; Mathiassen, Lars; Schultze, Ulrike

2017-01-01

discuss thenature of the academic article genre and the role of alternative ways of writing.We also introduce the six exemplars of alternative genres in the special issue,namely conversation, French new novel, meditation, memoir, allegory, andcrowdsourced research. We highlight key insights....... Furthermore, we wishto encourage Information Systems (IS) scholars to leverage a wider array ofalternative genres to present their research in order to develop new insights onsubject matters of interest to the IS discipline, as well as expand on howcontemporary and emergent phenomena of interest are conceived...... and contemplate theirimplications for current and future IS research....

Alternative Fuel Guidelines for Alternative Transportation Systems.

Science.gov (United States)

2011-01-31

The Volpe Center documented the increased use of alternative fuels on vehicles owned and operated by federal land management agencies. For each alternative fuel type, the Volpe Center documented the availability of vehicles, fueling mechanisms and pr...

Modular Energy Storage System for Alternative Energy Vehicles

Energy Technology Data Exchange (ETDEWEB)

Thomas, Janice [Magna Electronics Inc., Auburn Hills, MI (United States); Ervin, Frank [Magna Electronics Inc., Auburn Hills, MI (United States)

2012-05-15

An electrical vehicle environment was established to promote research and technology development in the area of high power energy management. The project incorporates a topology that permits parallel development of an alternative energy delivery system and an energy storage system. The objective of the project is to develop technologies, specifically power electronics, energy storage electronics and controls that provide efficient and effective energy management between electrically powered devices in alternative energy vehicles plugin electric vehicles, hybrid vehicles, range extended vehicles, and hydrogen-based fuel cell vehicles. In order to meet the project objectives, the Vehicle Energy Management System (VEMS) was defined and subsystem requirements were obtained. Afterwards, power electronics, energy storage electronics and controls were designed. Finally, these subsystems were built, tested individually, and integrated into an electric vehicle system to evaluate and optimize the subsystems performance. Phase 1 of the program established the fundamental test bed to support development of an electrical environment ideal for fuel cell application and the mitigation of many shortcomings of current fuel cell technology. Phase 2, continued development from Phase 1, focusing on implementing subsystem requirements, design and construction of the energy management subsystem, and the integration of this subsystem into the surrogate electric vehicle. Phase 2 also required the development of an Alternative Energy System (AES) capable of emulating electrical characteristics of fuel cells, battery, gen set, etc. Under the scope of the project, a boost converter that couples the alternate energy delivery system to the energy storage system was developed, constructed and tested. Modeling tools were utilized during the design process to optimize both component and system design. This model driven design process enabled an iterative process to track and evaluate the impact

Comparative health and safety assessment of alternative future electrical-generation systems

International Nuclear Information System (INIS)

Habegger, L.J.; Gasper, J.R.; Brown, C.D.

1980-01-01

The report is an analysis of health and safety risks of seven alternative electrical generation systems, all of which have potential for commercial availability in the post-2000 timeframe. The systems are compared on the basis of expected public and occupational deaths and lost workdays per year associated with 1000 MWe average unit generation. Risks and their uncertainties are estimated for all phases of the energy production cycle, including fuel and raw material extraction and processing, direct and indirect component manufacture, on-site construction, and system operation and maintenance. Also discussed is the potential significance of related major health and safety issues that remain largely unquantifiable. The technologies include: the SPS; a low-Btu coal gasification system with an open-cycle gas turbine combined with a steam topping cycle (CG/CC); a light water fission reactor system without fuel reprocessing (LWR); a liquid metal fast breeder fission reactor system (LMFBR); a central station terrestrial photovoltaic system (CTPV); and a first generation fusion system with magnetic confinement. For comparison with the baseload technologies, risk from a decentralized roof-top photovoltaic system with 6 kWe peak capacity and battery storage (DTPV) was also evaluated

Permafrost-An alternative target material for ultra-high energy neutrino detection?

International Nuclear Information System (INIS)

Nahnhauer, R.; Rostovtsev, A.A.; Tosi, D.

2008-01-01

The interest in the detection of cosmic neutrinos with energies above 10 17 eV has increased considerably in recent years. Possible target materials for in-matter arrays of ∼100 km 3 size under discussion are water, ice and rock salt. Here we propose to investigate permafrost as an additional alternative, covering ∼20% of Earth land surface and reaching down to more than 1000 m depth at certain locations. If sufficiently large attenuation lengths for radio and acoustic signals can be demonstrated by in-situ measurements, the construction of a large hybrid array within this material may be possible in the Northern Hemisphere. Properties and problems of a possible location in Siberia are discussed below. Some acoustic data are compared with laboratory measurements using 'artificial' permafrost

Alternate Materials In Design Of Radioactive Material Packages

International Nuclear Information System (INIS)

Blanton, P.; Eberl, K.

2010-01-01

This paper presents a summary of design and testing of material and composites for use in radioactive material packages. These materials provide thermal protection and provide structural integrity and energy absorption to the package during normal and hypothetical accident condition events as required by Title 10 Part 71 of the Code of Federal Regulations. Testing of packages comprising these materials is summarized.

Flue gas desulfurization gypsum: Its effectiveness as an alternative bedding material for broiler production

Science.gov (United States)

Flue gas desulfurization gypsum (FGDG) may be a viable low-cost alternative bedding material for broiler production. In order to evaluate FGD gypsum’s viability, three consecutive trials were conducted to determine its influence on live performance (body weight, feed consumption, feed efficiency, an...

Alternative geochemical barrier materials

International Nuclear Information System (INIS)

1991-07-01

Previous investigations of the effects of neutralization and reduction on uranium mill tailings pore fluids by the Technical Support Contractor indicated that arsenic, selenium, and molybdenum continue to remain in solution in all but reducing conditions. These hazardous constituents are present in groundwaters as oxyanions and, therefore, are not expected to be removed by adsorption into clays and most other soil constituents. It was decided to investigate the attenuation capacity of two commonly available crystalline iron oxides, taconite and scoria, and a zeolite, a network aluminosilicate with a cage structure. Columns of the candidate materials were exposed to solutions of individual constituents, including arsenic, molybdenum, selenium, and, uranium, and to the spiked tailings pore fluid from the Bodo Canyon disposal cell near Durango, Colorado. In addition to the single material columns, a homogeneous blend of the three materials and layers of the materials were exposed to spiked tailings pore fluids. The results of these experiments indicate that with the exception of molybdenum, the constituents of concern are attenuated by the taconite; however, they are not sufficiently attenuated to meet the groundwater protection standards applicable to the UMTRA Project. Therefore, the candidate barrier materials did not prove to be useful to the UMTRA Project for the cleanup of groundwaters

Revisiting the solar hydrogen alternative

Energy Technology Data Exchange (ETDEWEB)

Tomkiewicz, M. [Brooklyn College of CUNY, NY (United States)

1996-09-01

Research aimed at the development of technology to advance the solar-hydrogen alternative is per definition mission oriented. The priority that society puts on such research rise and fall with the priorities that we associate with the mission. The mission that we associate with the hydrogen economy is to provide a technological option for an indefinitely sustainable energy and material economies in which society is in equilibrium with its environment. In this paper we try to examine some global aspects of the hydrogen alternative and recommend formulation of a {open_quotes}rational{close_quotes} tax and regulatory system that is based on efforts needed to restore the ecological balance. Such a system, once entered into the price structure of the alternative energy schemes, will be used as a standard to compare energy systems that in turn will serve as a base for prioritization of publicly supported research and development.

Analysis of the Reliability of the "Alternator- Alternator Belt" System

Directory of Open Access Journals (Sweden)

Ivan Mavrin

2012-10-01

Full Text Available Before starting and also during the exploitation of va1ioussystems, it is vety imp011ant to know how the system and itsparts will behave during operation regarding breakdowns, i.e.failures. It is possible to predict the service behaviour of a systemby determining the functions of reliability, as well as frequencyand intensity of failures.The paper considers the theoretical basics of the functionsof reliability, frequency and intensity of failures for the twomain approaches. One includes 6 equal intetvals and the other13 unequal intetvals for the concrete case taken from practice.The reliability of the "alternator- alternator belt" system installedin the buses, has been analysed, according to the empiricaldata on failures.The empitical data on failures provide empirical functionsof reliability and frequency and intensity of failures, that arepresented in tables and graphically. The first analysis perfO!med by dividing the mean time between failures into 6 equaltime intervals has given the forms of empirical functions of fa ilurefrequency and intensity that approximately cotTespond totypical functions. By dividing the failure phase into 13 unequalintetvals with two failures in each interval, these functions indicateexplicit transitions from early failure inte1val into the randomfailure interval, i.e. into the ageing intetval. Functions thusobtained are more accurate and represent a better solution forthe given case.In order to estimate reliability of these systems with greateraccuracy, a greater number of failures needs to be analysed.

Application and Research Status of Alternative Materials for 3D-printing Technology

Directory of Open Access Journals (Sweden)

WANG Yanqing

2016-08-01

Full Text Available Application features and research status of alternative 3D-printing materials for six typical 3D-printingtechniques were reviewed. From the point of view of physical forms, four kinds of materials of liquid photosensitive resin material, thin sheet material (paper or plastic film , low melting point filament material and powder material are included. And from the composition point of view, nearly all kinds of materials in the production and life are included such as polymer materials: plastic, resin, wax; metal and alloy materials; ceramic materials. Liquid photosensitive resin material is used for stereo lithigraphy apparatus(SLA; thin sheet materials such as paper or plastic film are used for laminated object manufacturing(LOM; low melting point polymer filament materials such as wax filament, polyolefin resin filament, polyamide filament and ABS filament are used for fused deposition modeling(FDM; very wide variety powder materials including nylon powder, nylon-coated glass powder, polycarbonate powder, polyamide powder, wax powder, metal powder(Re-sintering and infiltration of copper are needed after sintering, wax-coated ceramic powder, wax-coated metal powder and thermosetting resin-coated fine sand are used for selective laser sintering(SLS. Nearly the same above powder materials are used for selective laser melting(SLM, but the printed parts own much more higher density and better mechanical properties. Powder materials are likewise used for threedimensional printing and gluing(3DP, however, the powders are stuck together by tricolor binder sprayed through nozzle and cross-section shape of the part is color-printed on it. Finally, the development direction in both quality and the yield of 3D-printing materials were pointed out to be a bottle-neck issue and a hot topic in the field of 3D-printing.

Extended abstracts of the 8. international symposium on new materials and nano-materials for electrochemical systems : emerging trends and challenges in new materials development for sustainable energy and environment

International Nuclear Information System (INIS)

Savadogo, O.; Ma, Z.F.

2010-01-01

This conference provided a forum to highlight the advances made in the development of new materials and nano-materials for electrochemical systems, including fuel cells. Electrochemical energy system devices have the potential to provide new applications for high power mobile systems as an alternative to internal combustion engines. They also have the potential for applications in hand-held personal electronic devices, uninterrupted power supply and auxiliary power supply. However, additional advances in unit cell material and design are still needed before mass production of fuel cells can begin. Cost, reliability, service life, electrode performance and power density are among the technical challenges facing commercialization. In addition to a plenary and general session, the sessions of the conference were entitled: low temperature fuel cells; high temperature fuel cells; advanced secondary rechargeable batteries; hydrogen production and storage; electrochemical supercapacitors; and poster session. All 166 presentations at this conference have been catalogued separately for inclusion in this database

Cost analysis of Navy acquisition alternatives for the NAVSTAR Global Positioning System

Science.gov (United States)

Darcy, T. F.; Smith, G. P.

1982-12-01

This research analyzes the life cycle cost (LCC) of the Navy's current and two hypothetical procurement alternatives for NAVSTAR Global Positioning System (GPS) user equipment. Costs are derived by the ARINC Research Corporation ACBEN cost estimating system. Data presentation is in a comparative format describing individual alternative LCC and differential costs between alternatives. Sensitivity analysis explores the impact receiver-processor unit (RPU) first unit production cost has on individual alternative LCC, as well as cost differentials between each alternative. Several benefits are discussed that might provide sufficient cost savings and/or system effectiveness improvements to warrant a procurement strategy other than the existing proposal.

Transitioning to Low-GWP Alternatives in Motor Vehicle Air Conditioning Systems

Science.gov (United States)

This fact sheet provides information on low-GWP alternatives in newly manufactured motor vehicle air conditioning systems. It discusses HFC alternatives, market trends, challenges to market entry for alternatives, and potential solutions.

local alternative sources for cogeneration combined heat and power system

Science.gov (United States)

Agll, Abdulhakim Amer

Global demand for energy continues to grow while countries around the globe race to reduce their reliance on fossil fuels and greenhouse gas emissions by implementing policy measures and advancing technology. Sustainability has become an important issue in transportation and infrastructure development projects. While several agencies are trying to incorporate a range of sustainability measures in their goals and missions, only a few planning agencies have been able to implement these policies and they are far from perfect. The low rate of success in implementing sustainable policies is primarily due to incomplete understanding of the system and the interaction between various elements of the system. The conventional planning efforts focuses mainly on performance measures pertaining to the system and its impact on the environment but seldom on the social and economic impacts. The objective of this study is to use clean and alternative energy can be produced from many sources, and even use existing materials for energy generation. One such pathway is using wastewater, animal and organic waste, or landfills to create biogas for energy production. There are three tasks for this study. In topic one evaluated the energy saving that produced from combined hydrogen, heat, and power and mitigate greenhouse gas emissions by using local sustainable energy at the Missouri S&T campus to reduce energy consumption and fossil fuel usage. Second topic aimed to estimate energy recovery and power generation from alternative energy source by using Rankin steam cycle from municipal solid waste at Benghazi-Libya. And the last task is in progress. The results for topics one and two have been presented.

Testing of Candidate Polymeric Materials for Compatibility with Pure Alternate Pretreat as Part of the Universal Waste Management System (UWMS)

Science.gov (United States)

Wingard, C. D.

2018-01-01

The Universal Waste Management System (UWMS) is an improved Waste Collection System for astronauts living and working in low Earth orbit spacecraft. Polymeric materials used in water recovery on International Space Station are regularly exposed to phosphoric acid-treated 'pretreated' urine. Polymeric materials used in UWMS are not only exposed to pretreated urine, but also to concentrated phosphoric acid with oxidizer before dilution known as 'pure pretreat.' Samples of five different polymeric materials immersed in pure pretreat for 1 year were tested for liquid compatibility by measuring changes in storage modulus with a dynamic mechanical analyzer.

Strategic importance of the New Materials in the Sustainable Development and as Alternative of competition

International Nuclear Information System (INIS)

Rodriguez E, Wilken; Bejarano B, Hernan; Villazon A, Hernando

1999-01-01

The new materials have a growing importance in the national development, and most of the industrialized countries are investing big supreme in the development of these, due to their great strategic paper in the global economic interaction. The present article seeks to give a general vision of the participation of these materials in the world economy as alternative factor of competition, keeping primarily in mind the conservation of the environment and the permanent search of the total quality

Material options for the superconducting rf system of the Future Circular Collider

CERN Document Server

Aull, Sarah; Butterworth, Andy; Schwerg, Nikolai

2018-01-01

The design of the superconducting RF (SRF) systems of the Future Circular Collider (FCC) machine variants requires a thorough comparison of the different options for cavity material, oper- ating temperature and frequency. We collected representative SRF performance data at different frequencies and temperatures of bulk niobium as the standard technology and of niobium thin films as a potential alternative and develop a perspective for future performance for all material- frequency-temperature combinations as function of accelerating gradient. Based on this perspective, we estimate the corresponding cryogenic grid power for the different FCC machines showing the most favourable accelerating gradients for the different materials and operating temperatures. Further- more, we discuss advantages, disadvantages and limitations of the different technology options to be taken into consideration.

The data base management system alternative for computing in the human services.

Science.gov (United States)

Sircar, S; Schkade, L L; Schoech, D

1983-01-01

The traditional incremental approach to computerization presents substantial problems as systems develop and grow. The Data Base Management System approach to computerization was developed to overcome the problems resulting from implementing computer applications one at a time. The authors describe the applications approach and the alternative Data Base Management System (DBMS) approach through their developmental history, discuss the technology of DBMS components, and consider the implications of choosing the DBMS alternative. Human service managers need an understanding of the DBMS alternative and its applicability to their agency data processing needs. The basis for a conscious selection of computing alternatives is outlined.

Assessment of a satellite power system and six alternative technologies

Energy Technology Data Exchange (ETDEWEB)

Wolsko, T.; Whitfield, R.; Samsa, M.; Habegger, L.S.; Levine, E.; Tanzman, E.

1981-04-01

The satellite power system is assessed in comparison to six alternative technologies. The alternatives are: central-station terrestrial photovoltaic systems, conventional coal-fired power plants, coal-gasification/combined-cycle power plants, light water reactor power plants, liquid-metal fast-breeder reactors, and fusion. The comparison is made regarding issues of cost and performance, health and safety, environmental effects, resources, socio-economic factors, and insitutional issues. The criteria for selecting the issues and the alternative technologies are given, and the methodology of the comparison is discussed. Brief descriptions of each of the technologies considered are included. (LEW)

Use of Augmentative and Alternative Communication Systems in Preschool: teacher perceptions

Directory of Open Access Journals (Sweden)

Munique Massaro

2013-06-01

Full Text Available Augmentative and Alternative Communication Resources have proven to be helpful in the insertion of students with disabilities and complex communication needs into a variety of pedagogical activities and expand the skills and competencies of the teacher in the teaching-learning. The objective of this research was to identify the perception of teachers regarding the use of augmentative and alternative communication during an intervention program in Preschool. Participants were a special class of Preschool students with disabilities and severe communication complexity, along with their teacher and the researcher. For the development of this research, a Alternative Communication Program was applied. The teacher was provided with systematic guidance concerning language and communication. In a collaborative process, three children’s songs were selected according to the teacher’s pedagogical planning and adapted resources through Augmentative and Alternative Communication Systems. During the intervention program, assisted evaluations also took place immediately after the activities with the music. The data were collected in audio recordings. For data analysis, content analysis was carried out resulting in the outlining of themes and sub-themes. Results indicated that the teacher identified that Augmentative and Alternative Communication Systems can to facilitate expression abilities of students with disabilities; that Augmentative and Alternative Communication Systems can be used by children in Preschool; and that resources adapted through augmentative and alternative communication systems should be in accordance with the specificities of students.

In vitro Alternative Methodologies for Central Nervous System Assessment: A Critique using Nanoscale Materials as an Example.

Science.gov (United States)

Identifying the potential health hazards to the central nervous system of a new family of materials presents many challenges. Whole-animal toxicity testing has been the tradition, but in vitro methods have been steadily gaining popularity. There are numerous challenges in testing...

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics

International Nuclear Information System (INIS)

Eisenberg, Daniel A.; Yu, Mengjing; Lam, Carl W.; Ogunseitan, Oladele A.; Schoenung, Julie M.

2013-01-01

Highlights: • Comparative alternatives assessment of thin film manufacturing technologies. • Development of chemical alternatives assessment in a life cycle context. • Screening of manufacturing and solar cell hazardous substances simultaneously. -- Abstract: Copper–indium–gallium–selenium–sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals™ and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS 2 p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane

Reference material systems: a sourcebook for material assessment

Energy Technology Data Exchange (ETDEWEB)

Bhagat, N. (ed.)

1976-12-01

A reference set of data related to material systems and a framework for carrying out the material technologies assessment are presented. While the bulk of renewables have been considered in this report, the nonrenewable materials dealt with here include structural materials only, such as steel, aluminum, cement and concrete, and bricks. The complete data set is supposed to include material flows, energy requirements, capital and labor inputs, and environmental effects for each process that a resource must go through to become a useful material for an end use. Although effort has been made to obtain as much information as possible, considerable gaps in data, apparent throughout this report, could not be avoided. A new material technology can be evaluated by substituting that technology for appropriate elements of the reference materials system and calculating the net change in material resource, energy, capital and labor requirements, and environmental impacts. This combination of information thus serves as a means of evaluating the potential benefits to be gained by research in various material technologies.

Papercrete brick as an alternate building material to control Environmental Pollution

Science.gov (United States)

Sudarsan, J. S.; Ramesh, S.; Jothilingam, M.; Ramasamy, Vishalatchi; Rajan, Rajitha J.

2017-07-01

Utilization of concrete in the construction industry is increasing day by day. The increasing demand for concrete in the future is the major issue, for which an alternate option is to find out at a reduced or no additional cost and to reduce the environmental impact due to increase of cement industries that are important ingredient to economic development. It turns out urgent to find out alternate for the partial replacement of concrete and cement, as natural sources of aggregates are becoming exhausted. As large quantity of paper waste is generated from different countries all over the world which causes serious environmental problems, So in this present study abandoned paper waste was used as a partial replacement material in concrete,. Study indicates that 80% of the construction cost of a building was contributed by building material and still millions of people in developing countries like India are not able to afford the cost of construction of house. This study is based on potential use of light weight composite brick as a building material and potential use of paper waste for producing at low-cost. Experimental investigation was carried out to analyse optimization of mix for papercrete bricks depending upon the water absorption, compressive strength and unit weight. Papercrete bricks were prepared out of waste paper, and quarry dust with partial replacement of cement by another industrial by-product Fly Ash in varying proportions of 25%, 40% and 55%. The properties like mechanical strength, standard quality comparisons with the conventional bricks through standard tests like hardness, soundness, fire resistance and Cost-Benefit Analysis were performed and studied. The specimens of dimension 230mm x 110mm x 80mm were subjected to 7 Days and 28 days air curing and sun drying before tests were performed on them. Based on the study it was found that for non-load bearing walls papercrete bricks are best suited.

Efficacy of pine leaves as an alternative bedding material for broiler chicks during summer season

Directory of Open Access Journals (Sweden)

Gourav Sharma

2015-10-01

Full Text Available Aim: The aim was to assess the efficacy of pine leaves as an alternative bedding material on the performance of broiler chicks. Materials and Methods: The present study was conducted in summer. Total 120, day old Vencobb straight run chicks were procured, and after 5 days of brooding, chicks were randomly distributed into four treatment groups viz. paddy husk (Group I, paddy straw (Group II, pine leaves (Group III, and combination of paddy straw and pine leaves (Group IV, each having 30 chicks with 3 replicates of 10 chicks each. Chicks were reared under intensive conditions in houses that have a semi-controlled environment, with optimum temperature and adequate ventilation. Food and water were provided as per NRC (1994 requirement. Results: The average body weight after 6 weeks of the experiment was 2018.83±31.11, 1983.80±33.27, 2007.36±35.73, and 1938.43±36.35 g. The bedding type had no significant effect on the carcass characteristics viz. evisceration rate and proportion of cut-up parts of the carcass except giblet yield. The experiment suggested that performance of broiler chicks reared on paddy straw and pine leaves as litter material, had improved body weight and feed conversion ratio as compared to rearing on paddy husk as bedding material. Bacterial count, parasitic load and the N, P, K value of manure of different bedding material shows no significant difference. Conclusion: Pine leaves have a potential to be used as an alternative source of litter material to economize poultry production in a sustainable way, so as to make poultry farming as a profitable entrepreneur.

Alternative approaches of SiC and related wide bandgap materials in light emitting and solar cell applications

International Nuclear Information System (INIS)

Wellman, P; Syväjärvi, M; Ou, H

2014-01-01

understanding the device performance. In relation to these, the surface pre-treatment and deposition technique can influence the reliability and electric field durability of the system, and relate to interface and near interface regions between the dielectric and semiconductor which can host electronic defects which change the surface potential, reduces mobility and enhance the recombination of charge carriers. At the end, materials for energy savings are critically needed. At the symposium ''Alternative approaches of SiC and related wide bandgap materials in light emitting and solar cell applications'', held at the E-MRS 2013 Spring meeting, 27–31 May, 2013 Strasbourg, France, a variety of concepts were presented. In this publication, a selection is presented that represents a range of issues from materials to reliability processing to system approaches. Acknowledgements: Technical support during preparation of the symposium program and proceedings by Saskia Schimmel is greatly acknowledged

Transparent Glass-Ceramics Produced by Sol-Gel: A Suitable Alternative for Photonic Materials.

Science.gov (United States)

Gorni, Giulio; Velázquez, Jose J; Mosa, Jadra; Balda, Rolindes; Fernández, Joaquin; Durán, Alicia; Castro, Yolanda

2018-01-30

Transparent glass-ceramics have shown interesting optical properties for several photonic applications. In particular, compositions based on oxide glass matrices with fluoride crystals embedded inside, known as oxyfluoride glass-ceramics, have gained increasing interest in the last few decades. Melt-quenching is still the most used method to prepare these materials but sol-gel has been indicated as a suitable alternative. Many papers have been published since the end of the 1990s, when these materials were prepared by sol-gel for the first time, thus a review of the achievements obtained so far is necessary. In the first part of this paper, a review of transparent sol-gel glass-ceramics is made focusing mainly on oxyfluoride compositions. Many interesting optical results have been obtained but very little innovation of synthesis and processing is found with respect to pioneering papers published 20 years ago. In the second part we describe the improvements in synthesis and processing obtained by the authors during the last five years. The main achievements are the preparation of oxyfluoride glass-ceramics with a much higher fluoride crystal fraction, at least double that reported up to now, and the first synthesis of NaGdF₄ glass-ceramics. Moreover, a new SiO₂ precursor was introduced in the synthesis, allowing for a reduction in the treatment temperature and favoring hydroxyl group removal. Interesting optical properties demonstrated the incorporation of dopant ions in the fluoride crystals, thus obtaining crystal-like spectra along with higher efficiencies with respect to xerogels, and hence demonstrating that these materials are a suitable alternative for photonic applications.

Measurement of the resistivity of porous materials with an alternating air-flow method.

Science.gov (United States)

Dragonetti, Raffaele; Ianniello, Carmine; Romano, Rosario A

2011-02-01

Air-flow resistivity is a main parameter governing the acoustic behavior of porous materials for sound absorption. The international standard ISO 9053 specifies two different methods to measure the air-flow resistivity, namely a steady-state air-flow method and an alternating air-flow method. The latter is realized by the measurement of the sound pressure at 2 Hz in a small rigid volume closed partially by the test sample. This cavity is excited with a known volume-velocity sound source implemented often with a motor-driven piston oscillating with prescribed area and displacement magnitude. Measurements at 2 Hz require special instrumentation and care. The authors suggest an alternating air-flow method based on the ratio of sound pressures measured at frequencies higher than 2 Hz inside two cavities coupled through a conventional loudspeaker. The basic method showed that the imaginary part of the sound pressure ratio is useful for the evaluation of the air-flow resistance. Criteria are discussed about the choice of a frequency range suitable to perform simplified calculations with respect to the basic method. These criteria depend on the sample thickness, its nonacoustic parameters, and the measurement apparatus as well. The proposed measurement method was tested successfully with various types of acoustic materials.

Plasmonic Glasses and Films Based on Alternative Inexpensive Materials for Blocking Infrared Radiation.

Science.gov (United States)

V Besteiro, Lucas; Kong, Xiang-Tian; Wang, Zhiming; Rosei, Federico; Govorov, Alexander O

2018-04-16

The need for energy-saving materials is pressing. This Letter reports on the design of energy-saving glasses and films based on plasmonic nanocrystals that efficiently block infrared radiation. Designing such plasmonic composite glasses is nontrivial and requires taking full advantage of both material and geometrical properties of the nanoparticles. We compute the performance of solar plasmonic glasses incorporating a transparent matrix and specially shaped nanocrystals. This performance depends on the shape and material of such nanocrystals. Glasses designed with plasmonic nanoshells are shown to exhibit overall better performances as compared to nanorods and nanocups. Simultaneously, scalable synthesis of plasmonic nanoshells and nanocups is technologically feasible using gas-phase fabrication methods. The computational simulations were performed for noble metals (gold and silver) as well as for alternative plasmonic materials (aluminum, copper, and titanium nitride). Inexpensive plasmonic materials (silver, copper, aluminum, and titanium nitride) show an overall good performance in terms of the commonly used figures of merit of industrial glass windows. Together with numerical data for specific materials, this study includes a set of general rules for designing efficient plasmonic IR-blocking media. The plasmonic glasses proposed herein are good candidates for the creation of cheap optical media, to be used in energy-saving windows in warm climates' housing or temperature-sensitive infrastructure.

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics

Energy Technology Data Exchange (ETDEWEB)

Eisenberg, Daniel A.; Yu, Mengjing; Lam, Carl W. [University of California, Davis, 1 Shields Avenue, Davis, CA 95616 (United States); Ogunseitan, Oladele A. [University of California, Irvine, Irvine, CA 92697 (United States); Schoenung, Julie M., E-mail: jmschoenung@ucdavis.edu [University of California, Davis, 1 Shields Avenue, Davis, CA 95616 (United States)

2013-09-15

Highlights: • Comparative alternatives assessment of thin film manufacturing technologies. • Development of chemical alternatives assessment in a life cycle context. • Screening of manufacturing and solar cell hazardous substances simultaneously. -- Abstract: Copper–indium–gallium–selenium–sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals™ and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS{sub 2} p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane.

Is there life after Buckley's Formocresol? Part I -- a narrative review of alternative interventions and materials.

Science.gov (United States)

Srinivasan, V; Patchett, C L; Waterhouse, P J

2006-03-01

(1) To present a narrative review of the currently available alternative interventions and materials to formocresol pulpotomy for the management of extensive caries in the primary molar, and (2) to produce a clinical protocol for pulp therapy techniques in the extensively carious primary molar. The International Agency for Research on Cancer has recently classified formaldehyde as carcinogenic to human beings. Since Buckley's Formocresol contains 19% formaldehyde in its full strength and, therefore, 1% in a 20% dilution, a safer alternative should be identified. A narrative review of the published literature for primary molar pulp therapy techniques was undertaken following an extensive and appropriate literature search. A specialist group of paediatric dentists was formed to arrive at a consensus and establish an evidence-based protocol for the management of extensively carious primary molar teeth. Part I of this paper explores the currently available alternative interventions and materials to formocresol in the form of a narrative review. The second part of the paper will present the formation of a specialist group to arrive at a consensus and establish an evidence-based protocol for the management of the extensively carious primary molar. After consideration of a review of extensively searched literature, a protocol and key points document have been developed to assist clinicians in their treatment planning. Further long-term studies with the highest level of evidence (i.e. randomized controlled trials) are required to enable us to identify acceptable alternatives which can replace formocresol.

Nuclear proliferation and civilian nuclear power: report of the Nonproliferation Alternative Systems Assessment Program. Volume VI. Safety and environmental considerations for licensing

International Nuclear Information System (INIS)

1979-12-01

Volume 6 of the Nonproliferation Alternative Systems Assessment Program report addresses safety and environmental considerations in licensing the principal alternative nuclear reactors and fuel cycles in the United States for large-scale commercial nuclear power plants. In addition, this volume examines the safety and environmental considerations for licensing fuel service centers. These centers, which have been proposed for controlling sensitive fuel-cycle facilities and special nuclear materials, would contain a combination of such facilities as reprocessing plants, fabrication plants, and reactors. For this analysis, two fuel service center concepts were selected - one with power-generating capability and one without. This volume also provides estimates of the time required for development of large-scale commercial reactor systems to reach the construction permit application stage and for fuel-cycle facilities to reach the operating license application stage, which is a measure of the relative technical status of alternative nuclear systems

PERFORMANCE OF ALTERNATIVE COMPONENT PRICING SYSTEMS FOR PORK

OpenAIRE

Brorsen, B. Wade; Akridge, Jay T.; Boland, Michael A.; Mauney, Sean; Forrest, John C.

1998-01-01

One method of implementing value-based marketing is a component pricing system. This research develops and evaluates alternative component pricing systems for pork. Two electronic technologies for estimating carcass components (optical probe and electromagnetic scanner) were evaluated on two sets of data representing different populations. Model accuracy increased as additional components were added.

Material control system simulator user's manual

International Nuclear Information System (INIS)

Hollstien, R.B.

1978-01-01

This report describes the use of a Material Control System Simulator (MCSS) program for determination of material accounting uncertainty and system response to particular adversary action sequences that constitute plausible material diversion attempts. The program is intended for use in situations where randomness, uncertainty, or interaction of adversary actions and material control system components make it difficult to assess safeguards effectiveness against particular material diversion attempts

Using Metaheuristic and Fuzzy System for the Optimization of Material Pull in a Push-Pull Flow Logistics Network

Directory of Open Access Journals (Sweden)

Afshin Mehrsai

2013-01-01

Full Text Available Alternative material flow strategies in logistics networks have crucial influences on the overall performance of the networks. Material flows can follow push, pull, or hybrid systems. To get the advantages of both push and pull flows in networks, the decoupling-point strategy is used as coordination mean. At this point, material pull has to get optimized concerning customer orders against pushed replenishment-rates. To compensate the ambiguity and uncertainty of both dynamic flows, fuzzy set theory can practically be applied. This paper has conceptual and mathematical parts to explain the performance of the push-pull flow strategy in a supply network and to give a novel solution for optimizing the pull side employing Conwip system. Alternative numbers of pallets and their lot-sizes circulating in the assembly system are getting optimized in accordance with a multi-objective problem; employing a hybrid approach out of meta-heuristics (genetic algorithm and simulated annealing and fuzzy system. Two main fuzzy sets as triangular and trapezoidal are applied in this technique for estimating ill-defined waiting times. The configured technique leads to smoother flows between push and pull sides in complex networks. A discrete-event simulation model is developed to analyze this thesis in an exemplary logistics network with dynamics.

Urban Transportation Planning Short Course: Evaluation of Alternative Transportation Systems.

Science.gov (United States)

Federal Highway Administration (DOT), Washington, DC.

This urban transportation pamphlet delves into the roles of policy groups and technical staffs in evaluating alternative transportation plans, evaluation criteria, systems to evaluate, and evaluation procedures. The introduction admits the importance of subjective, but informed, judgment as an effective tool in weighing alternative transportation…

Small Water System Alternatives: Media and Membrane Filtration Alternatives for Small Communities and Households

Science.gov (United States)

This webinar presentation will highlight research case studies on innovative drinking water treatment alternatives for small community water systems. Emphasis will be placed on media and membrane filtration technologies capable of meeting the requirements of the Long-Term 2 Enha...

Dataset on the innovation remediation technology of embankment dams by using suitable types of alternative raw materials

Directory of Open Access Journals (Sweden)

Drochytka Rostislav

2018-04-01

Full Text Available The data presented in this article are related to the research article entitled “Options for the remediation of embankment dams using suitable types of alternative raw (Drochytka and Kociánová, 2017 [1]. This article describes the possibility of use the fly ash as an optimal alternative material that can reduces costs and improves the rheological properties of the grouts. The grout data set is made publicly available to enable critical or extended analyses.

Using modified polyetheretherketone (PEEK) as an alternative material for endocrown restorations: A short-term clinical report.

Science.gov (United States)

Zoidis, Panagiotis; Bakiri, Eleonora; Polyzois, Gregory

2017-03-01

A modified polyetheretherketone (PEEK) framework material veneered with indirect light-polymerized composite resin was used as an alternative material for the fabrication of an endocrown restoration for an extensively damaged molar. The elastic modulus of the polyetheretherketone framework (4 GPa) veneered with indirect composite resin could dampen the occlusal forces protecting tooth structures better than ceramic materials. This is important in the restoration of extensively damaged molars with weak roots. Long-term clinical evidence is required before recommending the application as a substitute material. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Materials management information systems.

Science.gov (United States)

1996-01-01

The hospital materials management function--ensuring that goods and services get from a source to an end user--encompasses many areas of the hospital and can significantly affect hospital costs. Performing this function in a manner that will keep costs down and ensure adequate cash flow requires effective management of a large amount of information from a variety of sources. To effectively coordinate such information, most hospitals have implemented some form of materials management information system (MMIS). These systems can be used to automate or facilitate functions such as purchasing, accounting, inventory management, and patient supply charges. In this study, we evaluated seven MMISs from seven vendors, focusing on the functional capabilities of each system and the quality of the service and support provided by the vendor. This Evaluation is intended to (1) assist hospitals purchasing an MMIS by educating materials managers about the capabilities, benefits, and limitations of MMISs and (2) educate clinical engineers and information system managers about the scope of materials management within a healthcare facility. Because software products cannot be evaluated in the same manner as most devices typically included in Health Devices Evaluations, our standard Evaluation protocol was not applicable for this technology. Instead, we based our ratings on our observations (e.g., during site visits), interviews we conducted with current users of each system, and information provided by the vendor (e.g., in response to a request for information [RFI]). We divided the Evaluation into the following sections: Section 1. Responsibilities and Information Requirements of Materials Management: Provides an overview of typical materials management functions and describes the capabilities, benefits, and limitations of MMISs. Also includes the supplementary article, "Inventory Cost and Reimbursement Issues" and the glossary, "Materials Management Terminology." Section 2. The

Efficacy of pine leaves as an alternative bedding material for broiler chicks during summer season.

Science.gov (United States)

Sharma, Gourav; Khan, Asma; Singh, Surender; Anand, Ashok Kumar

2015-10-01

The aim was to assess the efficacy of pine leaves as an alternative bedding material on the performance of broiler chicks. The present study was conducted in summer. Total 120, day old Vencobb straight run chicks were procured, and after 5 days of brooding, chicks were randomly distributed into four treatment groups viz. paddy husk (Group I), paddy straw (Group II), pine leaves (Group III), and combination of paddy straw and pine leaves (Group IV), each having 30 chicks with 3 replicates of 10 chicks each. Chicks were reared under intensive conditions in houses that have a semi-controlled environment, with optimum temperature and adequate ventilation. Food and water were provided as per NRC (1994) requirement. The average body weight after 6 weeks of the experiment was 2018.83±31.11, 1983.80±33.27, 2007.36±35.73, and 1938.43±36.35 g. The bedding type had no significant effect on the carcass characteristics viz. evisceration rate and proportion of cut-up parts of the carcass except giblet yield. The experiment suggested that performance of broiler chicks reared on paddy straw and pine leaves as litter material, had improved body weight and feed conversion ratio as compared to rearing on paddy husk as bedding material. Bacterial count, parasitic load and the N, P, K value of manure of different bedding material shows no significant difference. Pine leaves have a potential to be used as an alternative source of litter material to economize poultry production in a sustainable way, so as to make poultry farming as a profitable entrepreneur.

Transparent Glass-Ceramics Produced by Sol-Gel: A Suitable Alternative for Photonic Materials

Directory of Open Access Journals (Sweden)

Giulio Gorni

2018-01-01

Full Text Available Transparent glass-ceramics have shown interesting optical properties for several photonic applications. In particular, compositions based on oxide glass matrices with fluoride crystals embedded inside, known as oxyfluoride glass-ceramics, have gained increasing interest in the last few decades. Melt-quenching is still the most used method to prepare these materials but sol-gel has been indicated as a suitable alternative. Many papers have been published since the end of the 1990s, when these materials were prepared by sol-gel for the first time, thus a review of the achievements obtained so far is necessary. In the first part of this paper, a review of transparent sol-gel glass-ceramics is made focusing mainly on oxyfluoride compositions. Many interesting optical results have been obtained but very little innovation of synthesis and processing is found with respect to pioneering papers published 20 years ago. In the second part we describe the improvements in synthesis and processing obtained by the authors during the last five years. The main achievements are the preparation of oxyfluoride glass-ceramics with a much higher fluoride crystal fraction, at least double that reported up to now, and the first synthesis of NaGdF4 glass-ceramics. Moreover, a new SiO2 precursor was introduced in the synthesis, allowing for a reduction in the treatment temperature and favoring hydroxyl group removal. Interesting optical properties demonstrated the incorporation of dopant ions in the fluoride crystals, thus obtaining crystal-like spectra along with higher efficiencies with respect to xerogels, and hence demonstrating that these materials are a suitable alternative for photonic applications.

Transparent Glass-Ceramics Produced by Sol-Gel: A Suitable Alternative for Photonic Materials

Science.gov (United States)

Gorni, Giulio; Mosa, Jadra; Balda, Rolindes; Fernández, Joaquin; Durán, Alicia; Castro, Yolanda

2018-01-01

Transparent glass-ceramics have shown interesting optical properties for several photonic applications. In particular, compositions based on oxide glass matrices with fluoride crystals embedded inside, known as oxyfluoride glass-ceramics, have gained increasing interest in the last few decades. Melt-quenching is still the most used method to prepare these materials but sol-gel has been indicated as a suitable alternative. Many papers have been published since the end of the 1990s, when these materials were prepared by sol-gel for the first time, thus a review of the achievements obtained so far is necessary. In the first part of this paper, a review of transparent sol-gel glass-ceramics is made focusing mainly on oxyfluoride compositions. Many interesting optical results have been obtained but very little innovation of synthesis and processing is found with respect to pioneering papers published 20 years ago. In the second part we describe the improvements in synthesis and processing obtained by the authors during the last five years. The main achievements are the preparation of oxyfluoride glass-ceramics with a much higher fluoride crystal fraction, at least double that reported up to now, and the first synthesis of NaGdF4 glass-ceramics. Moreover, a new SiO2 precursor was introduced in the synthesis, allowing for a reduction in the treatment temperature and favoring hydroxyl group removal. Interesting optical properties demonstrated the incorporation of dopant ions in the fluoride crystals, thus obtaining crystal-like spectra along with higher efficiencies with respect to xerogels, and hence demonstrating that these materials are a suitable alternative for photonic applications. PMID:29385706

Modernizing computerized nuclear material accounting systems

International Nuclear Information System (INIS)

Erkkila, B.H.; Claborn, J.

1995-01-01

DOE Orders and draft orders for nuclear material control and accountability address a complete material control and accountability (MC and A) program for all DOE contractors processing, using, or storing nuclear materials. A critical element of an MC and A program is the accounting system used to track and record all inventories of nuclear material and movements of materials in those inventories. Most DOE facilities use computerized accounting systems to facilitate the task of accounting for all their inventory of nuclear materials. Many facilities still use a mixture of a manual paper system with a computerized system. Also, facilities may use multiple systems to support information needed for MC and A. For real-time accounting it is desirable to implement a single integrated data base management system for a variety of users. In addition to accountability needs, waste management, material management, and production operations must be supported. Information in these systems can also support criticality safety and other safety issues. Modern networked microcomputers provide extensive processing and reporting capabilities that single mainframe computer systems struggle with. This paper describes an approach being developed at Los Alamos to address these problems

Fundamental characterization of alternate fuel effects in continuous combustion systems

Energy Technology Data Exchange (ETDEWEB)

Blazowski, W.S.; Edelman, R.B.; Harsha, P.T.

1978-09-11

The overall objective of this contract is to assist in the development of fuel-flexible combustion systems for gas turbines as well as Rankine and Stirling cycle engines. The primary emphasis of the program is on liquid hydrocarbons produced from non-petroleum resouces. Fuel-flexible combustion systems will provide for more rapid transition of these alternate fuels into important future energy utilization centers (especially utility power generation with the combined cycle gas turbine). The specific technical objectives of the program are to develop an improved understanding of relationships between alternate fuel properties and continuous combustion system effects, and to provide analytical modeling/correlation capabilities to be used as design aids for development of fuel-tolerant combustion systems. Efforts this past year have been to evaluate experimental procedures for studying alternate fuel combustion effects and to determine current analytical capabilities for prediction of these effects. Jet Stirred Combustor studies during this period have produced new insights into soot formation in strongly backmixed systems and have provided much information for comparison with analytical predictions. The analytical effort included new applications of quasi-global modeling techniques as well as comparison of prediction with the experimental results generated.

System and method for non-destructive evaluation of surface characteristics of a magnetic material

Science.gov (United States)

Jiles, David C.; Sipahi, Levent B.

1994-05-17

A system and a related method for non-destructive evaluation of the surface characteristics of a magnetic material. The sample is excited by an alternating magnetic field. The field frequency, amplitude and offset are controlled according to a predetermined protocol. The Barkhausen response of the sample is detected for the various fields and offsets and is analyzed. The system produces information relating to the frequency content, the amplitude content, the average or RMS energy content, as well as count rate information, for each of the Barkhausen responses at each of the excitation levels applied during the protocol. That information provides a contiguous body of data, heretofore unavailable, which can be analyzed to deduce information about the surface characteristics of the material at various depths below the surface.

Materials for spaceborne laser systems

International Nuclear Information System (INIS)

Gusarov, A.

2006-01-01

Advanced laser systems are attracting a growing interest for space missions, in particular for LIDAR (LIght Detection And Ranging) applications. An important issue for the LIDARs is the very strict requirements on the optical performance and more specifically the need for a high optical output power combined with a nearly perfect output beam quality. These features are traditionally in conflict with each other. Thermally induced phase distortions indeed corrupt the beam quality of high-power solid-state lasers and it becomes increasingly difficult to maintain a good beam quality while increasing the output power. A possible solution of the problem is to use the optical phase conjugation, which provides a method to dynamically correct for those aberrations. A process by which phase-conjugated waves can be generated is the SBS (stimulated Brillouin scattering). SBS mirrors commonly used in terrestrial application are based on liquids or gases, which are not 'space-friendly' and often toxic. The solid-state alternative seems the most appropriate for space. Such PCMs (Phase-Conjugating Mirrors) have been the subject of many research efforts in recent years and a significant progress in improving their characteristics has been achieved. However, the issue of space qualification remains open. To address it, the European Space Agency initiated in 2004 the research project named Solid-State Phase Conjugation, Radiation Testing and Evaluation for Core Laser Technologies with the TRT (Thales Research and Technology), France, as the prime contractor, and the CSL (Centre Spatial de Liege) and SCKCEN as the subcontractors. The project is to be completed in 2006. To qualify a PCM for a spaceborne laser system, one has to address a number of specific issues. Such a component must be mechanically rugged to sustain vibrations during the launch phase, provide a low out-gassing to prevent optical surfaces contamination in vacuum, be highly reliable to operate properly without

Effectiveness evaluation of alternative fixed-site safeguard security systems

International Nuclear Information System (INIS)

Chapman, L.D.

1976-01-01

An evaluation of a fixed-site physical protection system must consider the interrelationships of barriers, alarms, on-site and off-site guards, and their effectiveness against a forcible adversary attack intent on creating an act of sabotage of theft. A computer model, Forcible Entry Safeguard Effectiveness Model (FESEM), was developed for the evaluation of alternative fixed-site protection systems. It was written in the GASP IV simulation language. A hypothetical fixed-state protection system is defined and relative evaluations from a cost-effectiveness point of view are presented in order to demonstrate how the model can be used. Trade-offs involving on-site and off-site response forces and response times, perimeter system alarms, barrier configurations, and varying levels of threat are analyzed. The computer model provides a framework for performing inexpensive experiments on fixed-site security systems, for testing alternative decisions, and for determining the relative cost effectiveness associated with these decision policies

Material control system simulator program reference manual

Energy Technology Data Exchange (ETDEWEB)

Hollstien, R.B.

1978-01-24

A description is presented of a Material Control System Simulator (MCSS) program for determination of material accounting uncertainty and system response to particular adversary action sequences that constitute plausible material diversion attempts. The program is intended for use in situations where randomness, uncertainty, or interaction of adversary actions and material control system components make it difficult to assess safeguards effectiveness against particular material diversion attempts. Although MCSS may be used independently in the design or analysis of material handling and processing systems, it has been tailored toward the determination of material accountability and the response of material control systems to adversary action sequences.

Material control system simulator program reference manual

International Nuclear Information System (INIS)

Hollstien, R.B.

1978-01-01

A description is presented of a Material Control System Simulator (MCSS) program for determination of material accounting uncertainty and system response to particular adversary action sequences that constitute plausible material diversion attempts. The program is intended for use in situations where randomness, uncertainty, or interaction of adversary actions and material control system components make it difficult to assess safeguards effectiveness against particular material diversion attempts. Although MCSS may be used independently in the design or analysis of material handling and processing systems, it has been tailored toward the determination of material accountability and the response of material control systems to adversary action sequences

Analysis of alternative transportation methods for radioactive materials shipments including the use of special trains for spent fuel and wastes

International Nuclear Information System (INIS)

Smith, D.R.; Luna, R.E.; Taylor, J.M.

1978-01-01

Two studies were completed which evaluate the environmental impact of radioactive material transport. The first was a generic study which evaluated all radioactive materials and all transportation modes; the second addressed spent fuel and fuel-cycle wastes shipped by truck, rail and barge. A portion of each of those studies dealing with the change in impact resulting from alternative shipping methods is presented in this paper. Alternatives evaluated in each study were mode shifts, operational constraints, and, in generic case, changes in material properties and package capabilities. Data for the analyses were obtained from a shipper survey and from projections of shipments that would occur in an equilibrium fuel cycle supporting one hundred 1000-MW(e) reactors. Population exposures were deduced from point source radiation formulae using separation distances derived for scenarios appropriate to each shipping mode and to each exposed population group. Fourteen alternatives were investigated for the generic impact case. All showed relatively minor changes in the overall radiological impact. Since the radioactive material transport is estimated to be fewer than 3 latent cancer fatalities (LCF) for each shipment year (compared to some 300,000 yearly cancer fatalities or 5000 LCF's calculated for background radiation using the same radiological effects model), a 15% decrease caused by shifting from passenger air to cargo air is a relatively small effect. Eleven alternatives were considered for the fuel cycle/special train study, but only one produced a reduction in total special train baseline LCF's (.047) that was larger than 5%

Mobile liquid VR system: a cost effective alternative

International Nuclear Information System (INIS)

Soto, R.; Harkins, R.; HPD, Inc., Naperville, IL)

1985-01-01

The need for cost effective alternatives to treat large volumes of liquid radwaste has never been more evident. As part of a continuing effort to introduce such alternatives, HPD, Inc., and Chem-Nuclear Systems, Inc., have integrated two proven state-of-the-art technologies to offer a mobile liquid volume reduction system that satisfies nuclear industry requirements, with respect to liquid radwaste handling. This system optimizes proven technology by employing a crystallizer unit to concentrate the waste liquids to 50 weight percent solids, thereby reducing the volume to be solidified by factors of 40, while using only 20 percent of the energy required by conventional evaporative systems. In addition, the system employs a field proven cement solidification process which has been accepted in a Topical Report by the US NRC and which offers the highest waste to container volume ratios for stable waste forms in the industry. This volume reduction-solidification system is able to reduce over 7000 gallons of liquid waste per day to less than 30 cubic feet of 10CFR61 certified stable solidified waste for ultimate disposal or on-site storage. This document describes the GEODE System; its applicability; economics; volume reduction; scope of responsibility and experience. Major benefits include higher VR factors; assurance of continual regulatory compliance; and no capital investment

Nuclear material statistical accountancy system

International Nuclear Information System (INIS)

Argentest, F.; Casilli, T.; Franklin, M.

1979-01-01

The statistical accountancy system developed at JRC Ispra is refered as 'NUMSAS', ie Nuclear Material Statistical Accountancy System. The principal feature of NUMSAS is that in addition to an ordinary material balance calcultation, NUMSAS can calculate an estimate of the standard deviation of the measurement error accumulated in the material balance calculation. The purpose of the report is to describe in detail, the statistical model on wich the standard deviation calculation is based; the computational formula which is used by NUMSAS in calculating the standard deviation and the information about nuclear material measurements and the plant measurement system which are required as data for NUMSAS. The material balance records require processing and interpretation before the material balance calculation is begun. The material balance calculation is the last of four phases of data processing undertaken by NUMSAS. Each of these phases is implemented by a different computer program. The activities which are carried out in each phase can be summarised as follows; the pre-processing phase; the selection and up-date phase; the transformation phase, and the computation phase

Alternate design of ITER cryostat skirt support system

International Nuclear Information System (INIS)

Pandey, Manish Kumar; Gupta, Girish Kumar; Bhardwaj, Anil Kumar; Jha, Saroj Kumar

2015-01-01

The skirt support of ITER cryostat is a support system which takes all the load of cryostat cylinder and dome during normal and operational condition. The present design of skirt support has full penetration weld joints at the bottom (shell to horizontal plate joint). To fulfill the requirements of tolerances and control the welding distortions, we have proposed to change the full penetration weld into fillet weld. A detail calculation is done to check the feasibility and structural impact due to proposed design. The calculations provide the size requirements of fillet weld. To verify the structural integrity during most severe load case, finite element analysis (FEA) has been done in line with ASME section VIII division 2. By FEA 'Plastic Collapse' and 'Local Failure' modes has been assessed. 5° sector of skirt clamp has been modeled in CATIA V5 R21 and used in FEA. Fillet weld at shell to horizontal plate joint has been modeled and symmetry boundary condition at ± 2.5° applied. 'Elastic Plastic Analysis' has been performed for the most severe loading case i.e. Category IV loading. The alternate design of Cryostat Skirt support system has been found safe by analysis against Plastic collapse and Local Failure Modes with load proportionality factor 2.3. Alternate design of Cryostat skirt support system has been done and validated by FEA. As per alternate design, the proposal of fillet weld has been implemented in manufacturing. (author)

Fluidized bed combustion bottom ash: A better and alternative geo-material resource for construction.

Science.gov (United States)

Mandal, A K; Paramkusam, Bala Ramudu; Sinha, O P

2018-04-01

Though the majority of research on fly ash has proved its worth as a construction material, the utility of bottom ash is yet questionable due to its generation during the pulverized combustion process. The bottom ash produced during the fluidized bed combustion (FBC) process is attracting more attention due to the novelty of coal combustion technology. But, to establish its suitability as construction material, it is necessary to characterize it thoroughly with respect to the geotechnical as well as mineralogical points of view. For fulfilling these objectives, the present study mainly aims at characterizing the FBC bottom ash and its comparison with pulverized coal combustion (PCC) bottom ash, collected from the same origin of coal. Suitability of FBC bottom ash as a dike filter material in contrast to PCC bottom ash in replacing traditional filter material such as sand was also studied. The suitability criteria for utilization of both bottom ash and river sand as filter material on pond ash as a base material were evaluated, and both river sand and FBC bottom ash were found to be satisfactory. The study shows that FBC bottom ash is a better geo-material than PCC bottom ash, and it could be highly recommended as an alternative suitable filter material for constructing ash dikes in place of conventional sand.

Matching bunched beams to alternating gradient focusing systems

International Nuclear Information System (INIS)

Lysenko, W.P.

1980-07-01

A numerical procedure for generating phase-space distributions matched to alternating gradient focusing systems has been tested. For a smooth-focusing system a matched distribution can be calculated. With a particle tracing simulation code such a distribution can be followed while adiabatically deforming the focusing forces until an alternating gradient configuration is reached. The distribution remains matched; that is, the final distribution is periodic with the structure period. This method is useful because it can produce distributions matched to nonlinear forces. This is a feature that elliptical distributions, with ellipse parameters obtained from the Courant-Snyder theory, do not have. External nonlinearities, including nonlinear couplings, were included in our examples but space charge was not. This procedure is expected to work with space charge but will require a three-dimensional space charge calculation in the simulation code

Selection of high temperature thermal energy storage materials for advanced solar dynamic space power systems

Science.gov (United States)

Lacy, Dovie E.; Coles-Hamilton, Carolyn; Juhasz, Albert

1987-01-01

Under the direction of NASA's Office of Aeronautics and Technology (OAST), the NASA Lewis Research Center has initiated an in-house thermal energy storage program to identify combinations of phase change thermal energy storage media for use with a Brayton and Stirling Advanced Solar Dynamic (ASD) space power system operating between 1070 and 1400 K. A study has been initiated to determine suitable combinations of thermal energy storage (TES) phase change materials (PCM) that result in the smallest and lightest weight ASD power system possible. To date the heats of fusion of several fluoride salt mixtures with melting points greater than 1025 K have been verified experimentally. The study has indicated that these salt systems produce large ASD systems because of their inherent low thermal conductivity and low density. It is desirable to have PCMs with high densities and high thermal conductivities. Therefore, alternate phase change materials based on metallic alloy systems are also being considered as possible TES candidates for future ASD space power systems.

Ecology of Fungus Gnats (Bradysia spp.) in Greenhouse Production Systems Associated with Disease-Interactions and Alternative Management Strategies.

Science.gov (United States)

Cloyd, Raymond A

2015-04-09

Fungus gnats (Bradysia spp.) are major insect pests of greenhouse-grown horticultural crops mainly due to the direct feeding damage caused by the larvae, and the ability of larvae to transmit certain soil-borne plant pathogens. Currently, insecticides and biological control agents are being used successively to deal with fungus gnat populations in greenhouse production systems. However, these strategies may only be effective as long as greenhouse producers also implement alternative management strategies such as cultural, physical, and sanitation. This includes elimination of algae, and plant and growing medium debris; placing physical barriers onto the growing medium surface; and using materials that repel fungus gnat adults. This article describes the disease-interactions associated with fungus gnats and foliar and soil-borne diseases, and the alternative management strategies that should be considered by greenhouse producers in order to alleviate problems with fungus gnats in greenhouse production systems.

Ecology of Fungus Gnats (Bradysia spp. in Greenhouse Production Systems Associated with Disease-Interactions and Alternative Management Strategies

Directory of Open Access Journals (Sweden)

Raymond A. Cloyd

2015-04-01

Full Text Available Fungus gnats (Bradysia spp. are major insect pests of greenhouse-grown horticultural crops mainly due to the direct feeding damage caused by the larvae, and the ability of larvae to transmit certain soil-borne plant pathogens. Currently, insecticides and biological control agents are being used successively to deal with fungus gnat populations in greenhouse production systems. However, these strategies may only be effective as long as greenhouse producers also implement alternative management strategies such as cultural, physical, and sanitation. This includes elimination of algae, and plant and growing medium debris; placing physical barriers onto the growing medium surface; and using materials that repel fungus gnat adults. This article describes the disease-interactions associated with fungus gnats and foliar and soil-borne diseases, and the alternative management strategies that should be considered by greenhouse producers in order to alleviate problems with fungus gnats in greenhouse production systems.

Optimisation of integrated energy and materials systems

International Nuclear Information System (INIS)

Gielen, D.J.; Okken, P.A.

1994-06-01

To define cost-effective long term CO2 reduction strategies an integrated energy and materials system model for the Netherlands for the period 2000-2040 is developed. The model is based upon the energy system model MARKAL, which configures an optimal mix of technologies to satisfy the specified energy and product/materials service demands. This study concentrates on CO 2 emission reduction in the materials system. For this purpose, the energy system model is enlarged with a materials system model including all steps 'from cradle to grave'. The materials system model includes 29 materials, 20 product groups and 30 waste materials. The system is divided into seven types of technologies; 250 technologies are modeled. The results show that the integrated optimisation of the energy system and the materials system can significantly reduce the emission reduction costs, especially at higher reduction percentages. The reduction is achieved through shifts in materials production and waste handling and through materials substitution in products. Shifts in materials production and waste management seem cost-effective, while the cost-effectiveness of shifts in product composition is sensitive due to the cost structure of products. For the building sector, transportation applications and packaging, CO 2 policies show a significant impact on prices, and shifts in product composition could occur. For other products, the reduction through materials substitution seems less promising. The impact on materials consumption seems most significant for cement (reduced), timber and aluminium (both increased). For steel and plastics, the net effect is balanced, but shifts between applications do occur. The MARKAL-approach is feasible to study integrated energy and materials systems. The progress compared to other environmental system analysis instruments is much more insight in the interaction of technologies on a national scale and in time

Y-12 Integrated Materials Management System

Energy Technology Data Exchange (ETDEWEB)

Alspaugh, D. H.; Hickerson, T. W.

2002-06-03

The Integrated Materials Management System, when fully implemented, will provide the Y-12 National Security Complex with advanced inventory information and analysis capabilities and enable effective assessment, forecasting and management of nuclear materials, critical non-nuclear materials, and certified supplies. These capabilities will facilitate future Y-12 stockpile management work, enhance interfaces to existing National Nuclear Security Administration (NNSA) corporate-level information systems, and enable interfaces to planned NNSA systems. In the current national nuclear defense environment where, for example, weapons testing is not permitted, material managers need better, faster, more complete information about material properties and characteristics. They now must manage non-special nuclear material at the same high-level they have managed SNM, and information capabilities about both must be improved. The full automation and integration of business activities related to nuclear and non-nuclear materials that will be put into effect by the Integrated Materials Management System (IMMS) will significantly improve and streamline the process of providing vital information to Y-12 and NNSA managers. This overview looks at the kinds of information improvements targeted by the IMMS project, related issues, the proposed information architecture, and the progress to date in implementing the system.

Y-12 Integrated Materials Management System

International Nuclear Information System (INIS)

Alspaugh, D. H.; Hickerson, T. W.

2002-01-01

The Integrated Materials Management System, when fully implemented, will provide the Y-12 National Security Complex with advanced inventory information and analysis capabilities and enable effective assessment, forecasting and management of nuclear materials, critical non-nuclear materials, and certified supplies. These capabilities will facilitate future Y-12 stockpile management work, enhance interfaces to existing National Nuclear Security Administration (NNSA) corporate-level information systems, and enable interfaces to planned NNSA systems. In the current national nuclear defense environment where, for example, weapons testing is not permitted, material managers need better, faster, more complete information about material properties and characteristics. They now must manage non-special nuclear material at the same high-level they have managed SNM, and information capabilities about both must be improved. The full automation and integration of business activities related to nuclear and non-nuclear materials that will be put into effect by the Integrated Materials Management System (IMMS) will significantly improve and streamline the process of providing vital information to Y-12 and NNSA managers. This overview looks at the kinds of information improvements targeted by the IMMS project, related issues, the proposed information architecture, and the progress to date in implementing the system

Advanced EDL Materials (AEDLM)

Data.gov (United States)

National Aeronautics and Space Administration — Via the exploration of alternate resins and substrate materials for ablative TPS, and the development of new high heat flux resistant flexible TPS systems, we intend...

State alternative route designations

International Nuclear Information System (INIS)

1989-07-01

Pursuant to the Hazardous Materials Transportation Act (HMTA), the Department of Transportation (DOT) has promulgated a comprehensive set of regulations regarding the highway transportation of high-level radioactive materials. These regulations, under HM-164 and HM-164A, establish interstate highways as the preferred routes for the transportation of radioactive materials within and through the states. The regulations also provide a methodology by which a state may select alternative routes. First,the state must establish a ''state routing agency,'' defined as an entity authorized to use the state legal process to impose routing requirements on carriers of radioactive material (49 CFR 171.8). Once identified, the state routing agency must select routes in accordance with Large Quantity Shipments of Radioactive Materials or an equivalent routing analysis. Adjoining states and localities should be consulted on the impact of proposed alternative routes as a prerequisite of final route selection. Lastly, the states must provide written notice of DOT of any alternative route designation before the routes are deemed effective

Alternative Energetics DC Microgrid With Hydrogen Energy Storage System

Directory of Open Access Journals (Sweden)

Zaļeskis Genadijs

2016-12-01

Full Text Available This paper is related to an alternative energetics microgrid with a wind generator and a hydrogen energy storage system. The main aim of this research is the development of solutions for effective use of the wind generators in alternative energetics devices, at the same time providing uninterrupted power supply of the critical loads. In this research, it was accepted that the alternative energetics microgrid operates in an autonomous mode and the connection to the conventional power grid is not used. In the case when wind speed is low, the necessary power is provided by the energy storage system, which includes a fuel cell and a tank with stored hydrogen. The theoretical analysis of the storage system operation is made. The possible usage time of the stored hydrogen depends on the available amount of hydrogen and the consumption of the hydrogen by the fuel cell. The consumption, in turn, depends on used fuel cell power. The experimental results suggest that if the wind generator can provide only a part of the needed power, the abiding power can be provided by the fuel cell. In this case, a load filter is necessary to decrease the fuel cell current pulsations.

Design and hardware alternatives for a Safety-Parameter Display System

International Nuclear Information System (INIS)

Honeycutt, F.; Merten, W.T.; Roy, G.M.; Segraves, E.; Stone, G.P.

1981-05-01

The SPDS is a dedicated control room operator aid and is viewed as an important safety improvement within the context of other post-TMI fixes. Hardware configurations and components to implement the NSAC display format of a Safety Parameter Display System (SPDS) are evaluated. The evaluation was made on the basis of five alternative hardware configurations which use commercially available components. Four of the alternatives use computer/video display architecture. The fifth alternative is a simple hardwired system which uses strip chart recorders. SPDS regulatory requirements are defined by NUREG 0696. Overall feasibility of the NSAC concept was evaluated in terms of performance, reliability, cost, licensability, and flexibility. The flexibility evaluation relates to the ability to handle other display formats, the data acquisition needs of the other emergency facilities and the impact of expected future NRC requirements

Traditional medicine as an alternative form of health care system: A ...

African Journals Online (AJOL)

Traditional medicine as an alternative form of health care system: A preliminary case study of Nangabo sub-county, central Uganda. ... African Journal of Traditional, Complementary and Alternative Medicines ... The findings indicated that most (43%) respondents derive their livelihoods from traditional medicine practices.

Sensor-based material tagging system

International Nuclear Information System (INIS)

Vercellotti, L.C.; Cox, R.W.; Ravas, R.J.; Schlotterer, J.C.

1991-01-01

Electronic identification tags are being developed for tracking material and personnel. In applying electronic identification tags to radioactive materials safeguards, it is important to measure attributes of the material to ensure that the tag remains with the material. The addition of a microcontroller with an on-board analog-to-digital converter to an electronic identification tag application-specific integrated-circuit has been demonstrated as means to provide the tag with sensor data. Each tag is assembled into a housing, which serves as a scale for measuring the weight of a paint-can-sized container and its contents. Temperature rise of the can above ambient is also measured, and a piezoelectric detector detects disturbances and immediately puts the tag into its alarm and beacon mode. Radiation measurement was also considered, but the background from nearby containers was found to be excessive. The sensor-based tagging system allows tracking of the material in cans as it is stored in vaults or is moved through the manufacturing process. The paper presents details of the sensor-based material tagging system and describes a demonstration system

Nonproliferation and arms control assessment of weapons-usable fissile material storage and excess plutonium disposition alternatives

International Nuclear Information System (INIS)

1997-01-01

This report has been prepared by the Department of Energy's Office of Arms Control and Nonproliferation (DOE-NN) with support from the Office of Fissile Materials Disposition (DOE-MD). Its purpose is to analyze the nonproliferation and arms reduction implications of the alternatives for storage of plutonium and HEU, and disposition of excess plutonium, to aid policymakers and the public in making final decisions. While this assessment describes the benefits and risks associated with each option, it does not attempt to rank order the options or choose which ones are best. It does, however, identify steps which could maximize the benefits and mitigate any vulnerabilities of the various alternatives under consideration

Evaluation of hybrid power system alternatives: a case study

International Nuclear Information System (INIS)

Rosenthal, Andrew L.

1999-01-01

Pursuant to executive and statutory policies, the National Park Service (NPS) has been evaluating the use of photovoltaic (PV) hybrid power systems, for many of its remote, off-grid areas. This paper reports the results of a detailed technical and economic evaluation for one such area: the Needles District of Canyonlands National Park. The study evaluates the presented power systems and five alternative power generation configurations, four of which utilise PV. Projections are provided for the generator run-time and fuel use associated with each configuration as well as all initial and future costs. Included in the study are specific recommendations for energy efficiency improvements at the site. Results show that the generation systems presently in use, two full-time diesel generators, has the lowest conventional 20-year life cycle costs (LCC) of the six systems evaluated. However, when emissions costs are included (per NPS guidelines), several of the PV hybrid alternatives attain a lower LCC than the diesel-only systems. General discussion of the effects of initial versus future costs of PV hybrids as they compare with engine generator system is presented. (Author)

Computerized real-time materials accountability system for safeguards material control

International Nuclear Information System (INIS)

Spencer, W.F.; Affel, R.G.; Austin, H.C.; Nichols, J.P.; Stoutt, B.H.; Wachter, J.W.

1975-01-01

A real-time, computer-based system is described which provides safeguards material control at the Oak Ridge National Laboratory. Originally installed in 1972 to provide computerized real-time fissile materials accountability for criticality control purposes, the system has been expanded to provide accountability of all source and nuclear materials (SNM) and to utilize the on-line inventory files in support of the Laboratory physical protection and surveillance procedures. (auth)

MARAS - a computer code for semi-Markov reliability analysis of alternating systems

International Nuclear Information System (INIS)

Lee, Kwang Nam; Cho, Nam Zin

1989-01-01

It is now recognized that current testing and maintenance requirements invoke too many inadvertent reactor trips and that operating staff must devote significant amount of time and effort to comply with the requirements. With this recognition, the value and the impact of the proposed changes in the allowed outage time (AOT) and surveillance test interval(STI) are evaluated for the alternating system. Because of the testing and AOT requirements, the alternating system exhibits semi-Markovian characteristics which change states in accordance with a Markov chain but take a nonexponentially distributed amount of time between changes. It is observed from the results that there is an optimal point that gives lowest core damage probability and that the optimal point depends on input parameters. With these results, we can conclude that the methodology developed in this study can be applied to the existing alternating systems to evaluate accurately the various alternatives in the technical specifications

Material control and accountability alternatives

International Nuclear Information System (INIS)

1991-01-01

Department of Energy and Nuclear Regulatory Commission regulations governing material control and accountability in nuclear facilities have become more restrictive in the past decade, especially in areas that address the insider threat. As the insider threat receives greater credibility, regulations have been strengthened to increase the probability of detecting insider activity and to prevent removal of a significant quantity of Special Nuclear Material (SNM) from areas under control of the protective force

Elastic properties of a material composed of alternating layers of negative and positive Poisson's ratio

International Nuclear Information System (INIS)

Kocer, C.; McKenzie, D.R.; Bilek, M.M.

2009-01-01

The theory of elasticity predicts a variety of phenomena associated with solids that possess a negative Poisson's ratio. The fabrication of metamaterials with a 'designed' microstructure that exhibit a Poisson's ratio approaching the thermodynamic limits of 1/2 and -1 increases the likelihood of realising these phenomena for applications. In this work, we investigate the properties of a layered composite, with alternating layers of materials with negative and positive Poisson's ratio approaching the thermodynamic limits. Using the finite element method to simulate uniaxial loading and indentation of a free standing composite, we observed an increase in the resistance to mechanical deformation above the average value of the two materials. Even though the greatest increase in stiffness is gained as the thermodynamic limits are approached, a significant amount of added stiffness can be attained, provided that the Young's modulus of the negative Poisson's ratio material is not less than that of the positive Poisson's ratio material

Semi-Markov reliability analysis of alternating systems in a nuclear power plant

International Nuclear Information System (INIS)

Lee, K.N.; Cho, N.Z.

1992-01-01

Nuclear power plant operations that follow current testing and maintenance requirements sometimes result in inadvertent reactor trips, and operating staffs devote a significant amount of time and effort in complying with these requirements. Significant benefits could result from changes in current technical specifications. In this paper the benefits and impacts of changes in allowed outage times (AOTs) and surveillance test intervals (STIs) are evaluated for an alternative system that consists of multiple trains and whose operation is alternated train by train. because of testing and AOT requirements, the alternating system exhibits semi-Markovian characteristics that change states in accordance with a Markov process but take an arbitrarily distributed amount of time between changes. The state probabilities are quantified by memorizing the necessary number of past state probabilities. Two measures of plant performance, namely, core damage probability and plant unavailability (reactor downtime), were calculated for the evaluation of AOT and STI. Results indicate that there is an optimal point that gives the lowest core damage probability and that the methodology developed in this study can be applied to existing alternating systems to evaluate accurately the various alternatives in the technical specifications

Lessons learned by southern states in designating alternative routes

International Nuclear Information System (INIS)

1989-08-01

The purpose of this report is to discuss the ''lessons learned'' by the five states within the southem region that have designated alternative or preferred routes under the regulations of the Department of Transportation (DOT) established for the transportation of radioactive materials. The document was prepared by reviewing applicable federal laws and regulations, examining state reports and documents and contacting state officials and routing agencies involved in making routing decisions. In undertaking this project, the Southern States Energy Board hopes to reveal the process used by states that have designated alternative routes and thereby share their experiences (i.e., lessons learned) with other southern states that have yet to make designations. Under DOT regulations (49 CFR 177.826), carriers of highway route controlled quantities of radioactive materials (which include spent nuclear fuel and high-level waste) must use preferred routes selected to reduce time in transit. Such preferred routes consist of (1) an interstate system highway with use of an interstate system bypass or beltway around cities when available, and (2) alternate routes selected by a ''state routing agency.''

FMDP reactor alternative summary report: Volume 4, Evolutionary LWR alternative

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-01

Significant quantities of weapons-usable fissile materials [primarily plutonium and highly enriched uranium (HEU)] have become surplus to national defense needs both in the United States and Russia. These stocks of fissile materials pose significant dangers to national and international security. The dangers exist not only in the potential proliferation of nuclear weapons but also in the potential for environmental, safety, and health (ES&H) consequences if surplus fissile materials are not properly managed. The purpose of this report is to provide schedule, cost, and technical information that will be used to support the Record of Process (ROD). Following the screening process, DOE/MD via its national laboratories initiated a more detailed analysis activity to further evaluate each of the ten plutonium disposition alternatives that survived the screening process. Three ``Alternative Teams,`` chartered by DOE and comprised of technical experts from across the DOE national laboratory complex, conducted these analyses. One team was chartered for each of the major disposition classes (borehole, immobilization, and reactors). During the last year and a half, the Fissile Materials Disposition Program (FMDP) Reactor Alternative Team (RxAT) has conducted extensive analyses of the cost, schedule, technical maturity, S&S, and other characteristics of reactor-based plutonium disposition. The results of the RxAT`s analyses of the existing LWR, CANDU, and partially complete LWR alternatives are documented in Volumes 1-3 of this report. This document (Volume 4) summarizes the results of these analyses for the ELWR-based plutonium disposition option.

Integrated Photovoltaic System Used as an Alternative Power Source

Directory of Open Access Journals (Sweden)

Ionel Laurentiu Alboteanu

2014-09-01

Full Text Available This paper presents a solution to use solar energy as an alternative source of electricity to conventional sources. The solution is to use a compact photovoltaic system integrated into a micro smart grid. The studied photovoltaic system is used into concrete application for the power supply lighting in a didactic laboratory.

Alternative drives for motor cars. Hybrid systems, fuel cells, alternative energy sources. 3. ed.; Alternative Antriebe fuer Automobile. Hybridsysteme, Brennstoffzellen, alternative Energietraeger

Energy Technology Data Exchange (ETDEWEB)

Stan, Cornel [California Univ., Berkeley, CA (United States); Paris-1 Univ., 75 (France); Pisa Univ. (Italy); Perugia Univ. (Italy); Kronstadt Univ. (Russian Federation)

2012-07-01

This book describes and assesses on the basis of the latest research and development projects worldwide what the possibilities are for the realisation of future drive concepts, ranging from battery-driven electromotors to hybrid systems combining electromotor and combustion engine to alternative energy resources such as hydrogen or alcohol. Power density, torque band, acceleration characteristics, specific energy consumption and chemical and noise emissions are the most important criteria for assessing the quality of a drive configuration. The boundary conditions for the introduction of alternative automotive drives are determined by the availability or production characteristics and the storability of the energy resources in question as well as by the degree of technical complexity, costs, safety, infrastructure and service. This book provides an updated overview and analysis of the processes, prime movers and energy resources that can be combined in complex energy management systems for automobiles. Up-to-date information of this kind is indispensable for the development of new concepts. The contents in overview: current data and facts on the development of new concepts; compact overview and analysis of processes, prime movers and energy resources; methods and solutions in designing alternative drives. [German] Die Realisierungsmoeglichkeiten zukuenftiger Antriebskonzepte - von batteriebetriebenen Elektromotoren und Hybridsystemen bestehend aus Elektro- und Verbrennungsmotor ueber Brennstoffzellen bis hin zu alternativen Energietraegern wie Wasserstoff oder Alkohol - werden auf Basis neuesten Forschungs- und Entwicklungsarbeiten weltweit praesentiert und bewertet. Leistungsdichte, Drehmomentverlauf, Beschleunigungscharakteristik, spezifischer Energieverbrauch sowie Emission chemischer Stoffe und Geraeusche sind wichtige Merkmale zur Beurteilung der Qualitaet einer Antriebskonfiguration. Die Verfuegbarkeit oder die Herstellungsmerkmale sowie die Speicherfaehigkeit

New materials options for nuclear systems

International Nuclear Information System (INIS)

Jones, R.H.; Garner, F.A.; Bruemmer, S.M.; Gelles, D.S.

1989-01-01

Development of new materials for nuclear reactor systems is continuing to produce options for improved reactor designs. Materials with reduced environment-induced crack growth is a key materials issue for the light water reactor (LWR) industry while the development of low activation ferritic, austenitic and vanadium alloys has been an active area for materials development for fusion reactor structural applications. Development of advanced materials such as metal matrix and ceramic matrix composites for reactor systems have received a limited amount of attention. (author)

Alginate hydrogel as a potential alternative to hyaluronic acid as submucosal injection material.

Science.gov (United States)

Kang, Ki Joo; Min, Byung-Hoon; Lee, Jun Haeng; Kim, Eun Ran; Sung, Chang Ohk; Cho, Joo Young; Seo, Soo Won; Kim, Jae J

2013-06-01

Sodium alginate is currently used in medical products, including drugs and cosmetic materials. It can also be used as a submucosal injection material due to its excellent water retention ability. Alginate with a high water retention ability is called alginate hydrogel (AH). The aim of this study was to investigate the usefulness of AH as a submucosal injection material. To investigate the optimal viscosity of AH as a submucosal injection material, we observed the changes in submucosal height from the initial submucosal height in the stomachs of six miniature pigs for each injection material tested (0.3 % AH, 0.5 % hyaluronic acid, glycerol). All submucosal heights were compared serially over time (3, 5, 10, 20, and 30 min). Both immediate and 1-week delayed tissue reactions were investigated endoscopically in the same living pigs. Histological analyses were performed after the animals had been sacrificed. In a preliminary study, we determined that 0.3 % sodium alginate mixed with BaCl2 (400 μl) was the optimal viscosity of AH as an injection material. Our comparison of submucosal height changes over time showed that there was a significant decrease in submucosal height just 3 min following the injection of hyaluronic acid and glycerol, but that following the injection of AH a significant decrease in submucosal height was observed only after 10 min (p injection site. Alginate hydrogel demonstrated long-lasting maintenance of submucosal elevation, safety, and cost-effectiveness in a pig model, which makes it a potential alternative to hyaluronic acid.

A Grand Challenge for CMOS Scaling: Alternate Gate Dielectrics

Science.gov (United States)

Wallace, Robert M.

2001-03-01

Many materials systems are currently under consideration as potential replacements for SiO2 as the gate dielectric material for sub-0.13 um complementary metal oxide semiconductor (CMOS) technology. The prospect of replacing SiO2 is a formidable task because the alternate gate dielectric must provide many properties that are, at a minimum, comparable to those of SiO2 yet with a much higher permittivity. A systematic examination of the required performance of gate dielectrics suggests that the key properties to consider in the selection an alternative gate dielectric candidate are (a) permittivity, band gap and band alignment to silicon, (b) thermodynamic stability, (c) film morphology, (d) interface quality, (e) compatibility with the current or expected materials to be used in processing for CMOS devices, (f) process compatibility, and (g) reliability. Many dielectrics appear favorable in some of these areas, but very few materials are promising with respect to all of these guidelines. We will review the performance requirements for materials associated with CMOS scaling, the challenges associated with these requirements, and the state-of-the-art in current research for alternate gate dielectrics. The requirements for process integration compatibility are remarkably demanding, and any serious candidates will emerge only through continued, intensive investigation.

Alternatives generation and analysis for phase I intermediate waste feed staging system design requirements

Energy Technology Data Exchange (ETDEWEB)

Britton, M.D.

1996-10-02

This document provides; a decision analysis summary; problem statement; constraints, requirements, and assumptions; decision criteria; intermediate waste feed staging system options and alternatives generation and screening; intermediate waste feed staging system design concepts; intermediate waste feed staging system alternative evaluation and analysis; and open issues and actions.

Nonproliferation and arms control assessment of weapons-usable fissile material storage and excess plutonium disposition alternatives

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-01-01

This report has been prepared by the Department of Energy`s Office of Arms Control and Nonproliferation (DOE-NN) with support from the Office of Fissile Materials Disposition (DOE-MD). Its purpose is to analyze the nonproliferation and arms reduction implications of the alternatives for storage of plutonium and HEU, and disposition of excess plutonium, to aid policymakers and the public in making final decisions. While this assessment describes the benefits and risks associated with each option, it does not attempt to rank order the options or choose which ones are best. It does, however, identify steps which could maximize the benefits and mitigate any vulnerabilities of the various alternatives under consideration.

Minicomputer based, controlled materials information system

International Nuclear Information System (INIS)

Roberts, N.; Jessen, T.; Meadors, O.; Seibel, D.

1976-01-01

The LLL, Materials Management Group and Data Processing Services have developed a transaction-oriented, minicomputer system for the management of the Laboratory's controlled materials. The system consists of a multi-vendor hardware system designed for ease of operation, maximum reliability, and quick response and the requirements imposed on the hardware and software systems are discussed

Intelligent material systems - The dawn of a new materials age

International Nuclear Information System (INIS)

Rogers, C.A.

1993-01-01

The intelligent material system solution to such engineering problems as the design of a robotic arm borrows directly from biological analogs; materials that behave much as muscles do during contraction can be employed as induced strain actuators which work against the intrinsic structural impedance of the component. Unlike actual human arms, which are jointed, the intelligent structure may be a continuum. The adaptation of structural impedance may be regarded as the most fundamental and consequential concept in the field of intelligent material systems

Alternative pathways for angiotensin II generation in the cardiovascular system

Directory of Open Access Journals (Sweden)

C. Becari

2011-09-01

Full Text Available The classical renin-angiotensin system (RAS consists of enzymes and peptides that regulate blood pressure and electrolyte and fluid homeostasis. Angiotensin II (Ang II is one of the most important and extensively studied components of the RAS. The beneficial effects of angiotensin converting enzyme (ACE inhibitors in the treatment of hypertension and heart failure, among other diseases, are well known. However, it has been reported that patients chronically treated with effective doses of these inhibitors do not show suppression of Ang II formation, suggesting the involvement of pathways alternative to ACE in the generation of Ang II. Moreover, the finding that the concentration of Ang II is preserved in the kidney, heart and lungs of mice with an ACE deletion indicates the important role of alternative pathways under basal conditions to maintain the levels of Ang II. Our group has characterized the serine protease elastase-2 as an alternative pathway for Ang II generation from Ang I in rats. A role for elastase-2 in the cardiovascular system was suggested by studies performed in heart and conductance and resistance vessels of normotensive and spontaneously hypertensive rats. This mini-review will highlight the pharmacological aspects of the RAS, emphasizing the role of elastase-2, an alternative pathway for Ang II generation.

Nuclear proliferation and civilian nuclear power. Report of the Nonproliferation Alternative Systems Assessment Program. Volume VI. Safety and environmental considerations for licensing

International Nuclear Information System (INIS)

1980-06-01

This volume of the Nonproliferation Alternative Systems Assessment Program report addresses safety and environmental considerations in licensing the principal alternative nuclear reactors and fuel cycles in the United States for large-scale commercial nuclear power plants. In addition, this volume examines the safety and environmental considerations for licensing fuel service centers. These centers, which have been proposed for controlling sensitive fuel-cycle facilities and special nuclear materials, would contain a combination of such facilities as reprocessing plants, fabrication plants, and reactors. For this analysis, two fuel service center concepts were selected - one with power - generating capability and one without

FMDP reactor alternative summary report: Volume 4, Evolutionary LWR alternative

International Nuclear Information System (INIS)

1996-09-01

Significant quantities of weapons-usable fissile materials [primarily plutonium and highly enriched uranium (HEU)] have become surplus to national defense needs both in the United States and Russia. These stocks of fissile materials pose significant dangers to national and international security. The dangers exist not only in the potential proliferation of nuclear weapons but also in the potential for environmental, safety, and health (ES ampersand H) consequences if surplus fissile materials are not properly managed. The purpose of this report is to provide schedule, cost, and technical information that will be used to support the Record of Process (ROD). Following the screening process, DOE/MD via its national laboratories initiated a more detailed analysis activity to further evaluate each of the ten plutonium disposition alternatives that survived the screening process. Three ''Alternative Teams,'' chartered by DOE and comprised of technical experts from across the DOE national laboratory complex, conducted these analyses. One team was chartered for each of the major disposition classes (borehole, immobilization, and reactors). During the last year and a half, the Fissile Materials Disposition Program (FMDP) Reactor Alternative Team (RxAT) has conducted extensive analyses of the cost, schedule, technical maturity, S ampersand S, and other characteristics of reactor-based plutonium disposition. The results of the RxAT's analyses of the existing LWR, CANDU, and partially complete LWR alternatives are documented in Volumes 1-3 of this report. This document (Volume 4) summarizes the results of these analyses for the ELWR-based plutonium disposition option

Proposed alternatives for a DOE-wide occupational radiation exposure information system

International Nuclear Information System (INIS)

Murphy, B.L.; Murphy, D.W.; Fix, J.J.; Selby, J.M.; Vallario, E.J.

1984-02-01

The Radiation Exposure Information Reporting System (REIRS) was initiated by the Atomic Energy Commission (AEC) in 1968. While the system has provided a general overview of radiation exposures associated with AEC/ERDA/DOE operations and has satisfied the original intent for a central information system, the need for more detailed information has become evident. The alternatives addressed for a radiation exposure information system were no change in current system, clarification of DOE Order for current system, increased summary information from sites, centralized annual individual dose (exposure) system, and annual dose summary and locator files. A majority of the DOE Ad Hoc Committee has concurred to recommend the annual dose summary and locator files (ADSLF). The acceptance of the ADSLF alternative as the DOE-wide radiation exposure system would give DOE added capability and flexibility in responding to requests for information and would reduce the impact on the sites of special survey requests

Development of nuclear material accountancy control system

International Nuclear Information System (INIS)

Hirosawa, Naonori; Kashima, Sadamitsu; Akiba, Mitsunori

1992-01-01

PNC is developing a wide area of nuclear fuel cycle. Therefore, much nuclear material with a various form exists at each facility in the Works, and the controls of the inventory changes and the physical inventories of nuclear material are important. Nuclear material accountancy is a basic measure in safeguards system based on Non-Proliferation Treaty (NPT). In the light of such importance of material accountancy, the data base of nuclear material control and the material accountancy report system for all facilities has been developed by using the computer. By this system, accountancy report to STA is being presented certainly and timely. Property management and rapid corresponding to various inquiries can be carried out by the data base system which has free item searching procedure. (author)

Well-To-Wheel based fiscal systems. Can a WTW fiscal basis accelerate the introduction of alternative fuels?

International Nuclear Information System (INIS)

Van Bree, B.; Hanschke, C.B.

2011-09-01

This report explores to which extent alternative, (partially) Well-To-Wheel based fiscal systems may accelerate the introduction of low-carbon fuels and vehicles. The design of two alternative fiscal systems is described, as well as the challenges that any fiscal system must meet. The alternative systems are compared to the existing fiscal system with regard to (1) the extent to which they honour the 'polluter pays' principle, (2) the extent to which they are expected to accelerate the introduction of (alternative) gaseous fuels, liquid biofuels, and zero-emission vehicles, (3) their expected impact on the vehicle stock, and (4) a number of (undesired) side-effects. The results show that the alternative systems provide a stronger fiscal support for some alternative fuels and vehicles, but not for all.

Demonstration of a free piston Stirling engine driven linear alternator system. Annual report

International Nuclear Information System (INIS)

1978-01-01

The objective of the program is to develop a 2 kW Free Piston Stirling Engine/Linear Alternator Energy Conversion System for an isotopic heat source with a greater than 30% overall efficiency. The work was broken up into two phases. Phase I demonstrated the feasibility of the energy conversion system through analysis and experimental testing of the individual components. Phase II is a two-year effort to design, fabricate, and test a prototype demonstrator energy conversion system. The reprt documents the work performed during October 1976 through September 1977, the first year of Phase II. Details of the tasks are presented in five major sections: (1) Linear Alternator Development; (2) Engine/Alternator System Demonstration; (3) Demonstrator Preliminary Design; (4) Demonstrator Detailed Design; and (5) Development of Free Piston Stirling Engine Computer Simulation

Alternate symbol inversion for improved symbol synchronization in convolutionally coded systems

Science.gov (United States)

Simon, M. K.; Smith, J. G.

1980-01-01

Inverting alternate symbols of the encoder output of a convolutionally coded system provides sufficient density of symbol transitions to guarantee adequate symbol synchronizer performance, a guarantee otherwise lacking. Although alternate symbol inversion may increase or decrease the average transition density, depending on the data source model, it produces a maximum number of contiguous symbols without transition for a particular class of convolutional codes, independent of the data source model. Further, this maximum is sufficiently small to guarantee acceptable symbol synchronizer performance for typical applications. Subsequent inversion of alternate detected symbols permits proper decoding.

Alternative Drive Systems as a Part of a GHG Emission Reduction

Directory of Open Access Journals (Sweden)

Jevto Lučić

2011-09-01

Full Text Available Air pollution as a consequence of a modern way of life contaminates the natural environment and brings us the global warming which poses a clear and present danger to civilization. The main causes of global warming are greenhouse gasses, which arise of reliance on fossil fuels, deforestation, agriculture, industrial processes and transport. The transport itself makes 14% of the main causes of greenhouse gasses. Its dependence on fossil fuels, together with the decrease of a world fossil fuels reserves, force us to look for alternative fuels and to develop alternative drive systems, which can stabilize and reduce the greenhouse effect, and at the same time offer us new technologies, independent on a fossil fuels. This paper will try to present potential solutions for this problem, and to show the development of alternative drive systems

A Comparison of Five Alternative Approaches to Information Systems Development

Directory of Open Access Journals (Sweden)

Rudy Hirschheim

1997-11-01

Full Text Available The field of information systems (IS has grown dramatically over the past three decades. Recent trends have transformed the IS landscape. These trends include: the evolution of implementation technology from centralized mainframe environments towards distributed client-server architectures, embracing the internet and intranets; changes in user interface technology from character-based to graphical user interfaces, multimedia, and the World Wide Web; changes in applications from transaction processing systems towards systems supporting collaborative work; and the use of information technology as an enabler of business process reengineering and redesign. These technology changes coupled with changes in organizations and their operating environment, such as the growth of the network and virtual organization, internationalization and globalization of many organizations, intensified global competition, changes in values such as customer orientation (service quality and Quality of Working Life, have imposed new demands on the development of information systems. These changes have led to an increasing discussion about information systems development (ISO, and in particular, the various methods, tools, methodologies, and approaches for ISD. We believe such discussion has opened the door for new, alternative IS development approaches and methodologies. Our paper takes up this theme by describing five alternative ISD approaches, namely the Interactionist approach, the Speech Act-based approach, Soft Systems Methodology, the Trade Unionist approach, and the Professional Work Practices approach. Despite the fact that most of these approaches have a history of over 15 years, their relevance to IS development is not well recognized in the mainstream of IS practice and research, nor is their institutional status comparable to traditional approaches such as structured analysis and design methods. Therefore we characterize the five approaches as 'alternative' in

Exploring No-SQL alternatives for ALMA monitoring system

Science.gov (United States)

Shen, Tzu-Chiang; Soto, Ruben; Merino, Patricio; Peña, Leonel; Bartsch, Marcelo; Aguirre, Alvaro; Ibsen, Jorge

2014-07-01

The Atacama Large Millimeter /submillimeter Array (ALMA) will be a unique research instrument composed of at least 66 reconfigurable high-precision antennas, located at the Chajnantor plain in the Chilean Andes at an elevation of 5000 m. This paper describes the experience gained after several years working with the monitoring system, which has a strong requirement of collecting and storing up to 150K variables with a highest sampling rate of 20.8 kHz. The original design was built on top of a cluster of relational database server and network attached storage with fiber channel interface. As the number of monitoring points increases with the number of antennas included in the array, the current monitoring system demonstrated to be able to handle the increased data rate in the collection and storage area (only one month of data), but the data query interface showed serious performance degradation. A solution based on no-SQL platform was explored as an alternative to the current long-term storage system. Among several alternatives, mongoDB has been selected. In the data flow, intermediate cache servers based on Redis were introduced to allow faster streaming of the most recently acquired data to web based charts and applications for online data analysis.

Materials And Processes Technical Information System (MAPTIS) LDEF materials data base

Science.gov (United States)

Funk, Joan G.; Strickland, John W.; Davis, John M.

1993-01-01

A preliminary Long Duration Exposure Facility (LDEF) Materials Data Base was developed by the LDEF Materials Special Investigation Group (MSIG). The LDEF Materials Data Base is envisioned to eventually contain the wide variety and vast quantity of materials data generated from LDEF. The data is searchable by optical, thermal, and mechanical properties, exposure parameters (such as atomic oxygen flux) and author(s) or principal investigator(s). Tne LDEF Materials Data Base was incorporated into the Materials and Processes Technical Information System (MAPTIS). MAPTIS is a collection of materials data which has been computerized and is available to engineers, designers, and researchers in the aerospace community involved in the design and development of spacecraft and related hardware. The LDEF Materials Data Base is described and step-by-step example searches using the data base are included. Information on how to become an authorized user of the system is included.

40 CFR 75.48 - Petition for an alternative monitoring system.

Science.gov (United States)

2010-07-01

... method of ensuring an accurate assessment of operating hourly conditions on a real-time basis. (9) A...) Hourly test data for the alternative monitoring system at each required operating level and fuel type... continuous emissions monitoring system at each required operating level and fuel type. The fuel type...

Alternative wastewatersystems

DEFF Research Database (Denmark)

Dyck-Madsen, Søren; Hoffmann, Birgitte; Gabriel, Søren

1999-01-01

The report:-  Communicates experiences from Swedish buildings from the establishment and running of alternative wastewater systems. Communicates pictures of alternative buildings and wastewater systems in Sweden. Gives a short evaluation of the performance and the sustainability of the systems....

Evaluating energy-system alternatives in the context of sustainable development

International Nuclear Information System (INIS)

Wilson, D.

1993-01-01

Growing awareness of the negative social, environmental and economic impacts caused by the production, distribution and end-use consumption of energy has led the search for alternatives to become increasingly urgent and complex. The need for analytical methods and tools for evaluating options and opportunities is particularly acute in rapidly developing countries. The aim of this article is to illustrate the broad range of issues and impacts that are important for evaluating and comparing energy-system alternatives in the context of sustainable development. The feasibility of producing and utilizing biomass-based ethanol as an alternative transportation fuel in Thailand is explored herein to provide examples and a forum for discussion of these issues. Scenarios describe the conditions under which a significant potential for fuel-switching to domestically-produced ethanol appears to exist. Harnessing this potential could lead to important improvements in the energy system's impacts on human health, Thailand's economy, and the environment. Achieving these improvements, however, would require comprehensive and long-term planning and support on the part of the Thai government

Alternative irradiation system for efficiency manganese bath determination

Energy Technology Data Exchange (ETDEWEB)

Passos Leite, Sandro, E-mail: sandro@ird.gov.b [Programa de Engenharia Nuclear/COPPE, Universidade Federal do Rio de Janeiro, Ilha do Fundao, Caixa Postal 68509, 21945-970, Rio de Janeiro, RJ (Brazil); Wagner Pereira, Walsan, E-mail: walsan@ird.gov.b [Instituto de Radioprotecao e Dosimetria LNMRI/IRD/CNEN, Av. Salvador Allende, s/no, Recreio dos Bandeirantes, CEP: 22780-160, Rio de Janeiro (Brazil); Xavier da Silva, Ademir, E-mail: ademir@con.ufrj.b [Programa de Engenharia Nuclear/COPPE, Universidade Federal do Rio de Janeiro, Ilha do Fundao, Caixa Postal 68509, 21945-970, Rio de Janeiro, RJ (Brazil); Simoes da Fonseca, Evaldo, E-mail: evaldo@ird.gov.b [Instituto de Radioprotecao e Dosimetria LNMRI/IRD/CNEN, Av. Salvador Allende, s/no, Recreio dos Bandeirantes, CEP: 22780-160, Rio de Janeiro (Brazil); Souza Patrao, Karla Cristina de, E-mail: karla@ird.gov.b [Instituto de Radioprotecao e Dosimetria LNMRI/IRD/CNEN, Av. Salvador Allende, s/no, Recreio dos Bandeirantes, CEP: 22780-160, Rio de Janeiro (Brazil)

2010-12-15

An alternative irradiation system, which works with a radionuclide neutron source and manganese sulphate solution volume have been proposed for efficiency determination of a Manganese Bath System (MBS). This irradiation system was designed by simulation with MCNP5 code, considering a californium neutron source in several manganese sulphate volumes and different neutron reflectors. Although its solution specific activity are less than those in nuclear reactors, the simulation results have showed that the irradiation system proposed takes a manganese neutron capture increase up to 200 times when it compared to manganese neutron capture from a MBS whose diameter is about 100 cm. That becomes possible to use those samples for some of the absolute specific activity measuring methods.

Nuclear proliferation and civilian nuclear power: report of the Nonproliferation Alternative Systems Assessment Program. Volume V. Economics and systems analysis

International Nuclear Information System (INIS)

1979-12-01

This assessment considers the economics of alternative nuclear reactor and fuel-cycle systems in the light of possible patterns of uranium supply and energy demand, as well as the economic implications of improving the proliferation resistance of the various systems. The assessment focuses on the costs of alternative nuclear technologies and the possible timing of their implementation, based on their economic attractiveness. The objectives of this assessment are to identify when economic incentives to deploy advanced nuclear power systems might exist, to estimate the costs of using technologies that would reduce the risk of proliferation, to assess the impact of major economic uncertainties on the transition to new technologies, and to compare the investments required for alternative systems. This information can then be used to assess the potential economic benefits of alternative research, development, and demonstration programs and the timing of those programs

Nuclear proliferation and civilian nuclear power: report of the Nonproliferation Alternative Systems Assessment Program. Volume V. Economics and systems analysis

Energy Technology Data Exchange (ETDEWEB)

None

1979-12-01

This assessment considers the economics of alternative nuclear reactor and fuel-cycle systems in the light of possible patterns of uranium supply and energy demand, as well as the economic implications of improving the proliferation resistance of the various systems. The assessment focuses on the costs of alternative nuclear technologies and the possible timing of their implementation, based on their economic attractiveness. The objectives of this assessment are to identify when economic incentives to deploy advanced nuclear power systems might exist, to estimate the costs of using technologies that would reduce the risk of proliferation, to assess the impact of major economic uncertainties on the transition to new technologies, and to compare the investments required for alternative systems. This information can then be used to assess the potential economic benefits of alternative research, development, and demonstration programs and the timing of those programs.

PAMTRAK: A personnel and material tracking system

International Nuclear Information System (INIS)

Anspach, D.A.; Anspach, J.P.; Crain, B. Jr.

1996-01-01

There is a need for an automated system for protecting and monitoring sensitive or classified parts and material. Sandia has developed a real-time personnel and material tracking system (PAMTRAK) that has been installed at selected DOE facilities. It safeguards sensitive parts and material by tracking tags worn by personnel and by monitoring sensors attached to the parts or material. It includes remote control and alarm display capabilities and a complementary program in Keyhole to display measured material attributes remotely. This paper describes the design goals, the system components, current installations, and the benefits a site can expect when using PAMTRAK

Alternative Plasmonic Materials: Alternative Plasmonic Materials: Beyond Gold and Silver (Adv. Mater. 24/2013)

DEFF Research Database (Denmark)

Naik, Gururaj V.; Shalaev, Vladimir M.; Boltasseva, Alexandra

2013-01-01

and new functionalities with applications in sensing, imaging, data storage, novel light sources, energy conversion, quantum optics and others. The cover image depicts a negatively refracting metamaterial device built from novel materials. Image prepared with the help of Dr. Alexander V. Kildishev....

An alternative approach to contrast-detail testing of X-ray image intensifier systems

International Nuclear Information System (INIS)

Kotre, C.J.; Marshall, N.W.; Faulkner, K.

1992-01-01

The difficulties of making the results of threshold contrast-detail diameter tests on X-ray image intensifier systems consistent with published performance standards are discussed. The current approach to contrast-detail testing is described and an alternative method intended to give greater consistency for all image intensifier input field diameters proposed. The current and alternative test conditions are compared on two image intensifier systems. The results obtained show that the contrast-detail curves for image intensifier systems with a wide range of input field diameters can be effectively normalized to be directly comparable to a common reference standard by applying the proposed alternative test conditions. The implications of this result on the interpretation of the contrast-detail test are discussed. (author)

An alternative approach to the management of reactive metals: tolerant cementitious systems

International Nuclear Information System (INIS)

Swift, P.; Cox, J.; Wise, M.; McKinney, J.; Rhodes, C.

2015-01-01

In recent years research has focused on preventing or minimising corrosion of reactive metals to ensure long-term waste package integrity. An alternative approach to the encapsulation of reactive metals is being explored. The approach will identify a cementitious-based encapsulating material that will allow corrosion of reactive metals to occur in a controlled and predictable manner, rather than seeking to limit or prevent the corrosion, whilst retaining waste package integrity. A low strength grout will be developed that will be 'tolerant' to the expansive forces generated by the corrosion products of reactive metals. Novel cementitious systems (e.g. foamed cements, rubber composite cements, cenosphere composite cements, lime mortars, bentonite cements etc.) that may be tolerant to potentially expansive waste products, such as reactive metals will be considered and assessed in a series of small-scale preliminary trials (compressive strength, porosity, permeability, pore solution pH, etc.)

Materials handbook for fusion energy systems

Science.gov (United States)

Davis, J. W.; Marchbanks, M. F.

A materials data book for use in the design and analysis of components and systems in near term experimental and commercial reactor concepts has been created by the Office of Fusion Energy. The handbook is known as the Materials Handbook for Fusion Energy Systems (MHFES) and is available to all organizations actively involved in fusion related research or system designs. Distribution of the MHFES and its data pages is handled by the Hanford Engineering Development Laboratory (HEDL), while its direction and content is handled by McDonnell Douglas Astronautics Company — St. Louis (MDAC-STL). The MHFES differs from other handbooks in that its format is geared more to the designer and structural analyst than to the materials scientist or materials engineer. The format that is used organizes the handbook by subsystems or components rather than material. Within each subsystem is information pertaining to material selection, specific material properties, and comments or recommendations on treatment of data. Since its inception a little more than a year ago, over 80 copies have been distributed to over 28 organizations consisting of national laboratories, universities, and private industries.

Waste management system alternatives for treatment of wastes from spent fuel reprocessing

International Nuclear Information System (INIS)

McKee, R.W.; Swanson, J.L.; Daling, P.M.

1986-09-01

This study was performed to help identify a preferred TRU waste treatment alternative for reprocessing wastes with respect to waste form performance in a geologic repository, near-term waste management system risks, and minimum waste management system costs. The results were intended for use in developing TRU waste acceptance requirements that may be needed to meet regulatory requirements for disposal of TRU wastes in a geologic repository. The waste management system components included in this analysis are waste treatment and packaging, transportation, and disposal. The major features of the TRU waste treatment alternatives examined here include: (1) packaging (as-produced) without treatment (PWOT); (2) compaction of hulls and other compactable wastes; (3) incineration of combustibles with cementation of the ash plus compaction of hulls and filters; (4) melting of hulls and failed equipment plus incineration of combustibles with vitrification of the ash along with the HLW; (5a) decontamination of hulls and failed equipment to produce LLW plus incineration and incorporation of ash and other inert wastes into HLW glass; and (5b) variation of this fifth treatment alternative in which the incineration ash is incorporated into a separate TRU waste glass. The six alternative processing system concepts provide progressively increasing levels of TRU waste consolidation and TRU waste form integrity. Vitrification of HLW and intermediate-level liquid wastes (ILLW) was assumed in all cases

Antimicrobial Materials for Advanced Microbial Control in Spacecraft Water Systems

Science.gov (United States)

Birmele, Michele; Caro, Janicce; Newsham, Gerard; Roberts, Michael; Morford, Megan; Wheeler, Ray

2012-01-01

Microbial detection, identification, and control are essential for the maintenance and preservation of spacecraft water systems. Requirements set by NASA put limitations on the energy, mass, materials, noise, cost, and crew time that can be devoted to microbial control. Efforts are being made to attain real-time detection and identification of microbial contamination in microgravity environments. Research for evaluating technologies for capability enhancement on-orbit is currently focused on the use of adenosine triphosphate (ATP) analysis for detection purposes and polymerase chain reaction (peR) for microbial identification. Additional research is being conducted on how to control for microbial contamination on a continual basis. Existing microbial control methods in spacecraft utilize iodine or ionic silver biocides, physical disinfection, and point-of-use sterilization filters. Although these methods are effective, they require re-dosing due to loss of efficacy, have low human toxicity thresholds, produce poor taste, and consume valuable mass and crew time. Thus, alternative methods for microbial control are needed. This project also explores ultraviolet light-emitting diodes (UV-LEDs), surface passivation methods for maintaining residual biocide levels, and several antimicrobial materials aimed at improving current microbial control techniques, as well as addressing other materials presently under analysis and future directions to be pursued.

Online Instruction: An Alternative Delivery System for Higher Education

Science.gov (United States)

Wronkovich, Michael

2003-01-01

In an increasingly technological society, delivery systems for professional development and higher education have greatly expanded. Video conferencing and web-based alternatives provide opportunities to extend the college campus far beyond the boundaries traditionally considered feasible. Adult learners have found the convenience of web-based…

Structural Materials for Efficient Energy Production Systems

International Nuclear Information System (INIS)

Gomez Briceno, D.

2009-01-01

Increasing the efficiency of electric power production systems implies increasing the operating temperature above those of systems currently in operation. The viability of new systems depends completely on the availability of structural materials that withstand the operating conditions specified in the design: adequate features under mechanical stress at high temperatures and compatibility with the medium. In the case of nuclear systems (fission, fusion), an important requirement is their response to irradiation induced damage. In spite of the significant differences that exist in the design of nuclear power plants, fusion reactors, innovative fission systems, supercritical fossil plants, biomass plants, solar concentration thermal plants, etc., all of them have as a common characteristic the use of resistant materials at high temperatures. The qualification of existing materials for the new and more demanding operating conditions and the development of new materials is one of the challenges faced by the electric power production industry. The science of materials and the understanding of the basic processes that take place in structural materials on exposure to the operating conditions of energy production systems are the tools that are available to obtain safe and economically viable solutions. (Authors) 4 refs.

Material control system simulator user's manual

Energy Technology Data Exchange (ETDEWEB)

Hollstien, R.B.

1978-01-24

This report describes the use of a Material Control System Simulator (MCSS) program for determination of material accounting uncertainty and system response to particular adversary action sequences that constitute plausible material diversion attempts. The program is intended for use in situations where randomness, uncertainty, or interaction of adversary actions and material control system components make it difficult to assess safeguards effectiveness against particular material diversion attempts.

Efficiency analysis system of material management

Directory of Open Access Journals (Sweden)

Bogusław Śliwczyński

2012-12-01

Full Text Available Background: Significant scope of enterprise's efficiency management is improving of material management process both the strategic and operational level. The complexity of material flow processes can lead to a threat such as distraction and disintegration of analysis focusing on many different factors influenced on effective sourcing and procurement management, transport and warehousing processes, inventory management, working capital and cash flow management. Material and methods: The presented article focuses on multidimensional and multi-criteria analysis of material management efficiency that is considered as decision support system. Authors have presented results of the research regarding ineffective material management confirm insufficient analytical supporting in various decisions of procurement operations. Results and conclusions: Based on research results authors presented in the article model of efficiency analysis system of material management.

MHSS: a material handling system simulator

Energy Technology Data Exchange (ETDEWEB)

Pomernacki, L.; Hollstien, R.B.

1976-04-07

A Material Handling System Simulator (MHSS) program is described that provides specialized functional blocks for modeling and simulation of nuclear material handling systems. Models of nuclear fuel fabrication plants may be built using functional blocks that simulate material receiving, storage, transport, inventory, processing, and shipping operations as well as the control and reporting tasks of operators or on-line computers. Blocks are also provided that allow the user to observe and gather statistical information on the dynamic behavior of simulated plants over single or replicated runs. Although it is currently being developed for the nuclear materials handling application, MHSS can be adapted to other industries in which material accountability is important. In this paper, emphasis is on the simulation methodology of the MHSS program with application to the nuclear material safeguards problem. (auth)

The system of nuclear material control of Kazakhstan

International Nuclear Information System (INIS)

Yeligbayeva, G.Zh.

2001-01-01

Full text: The State system for nuclear material control consists of three integral components. The efficiency of each is to guarantee the non-proliferation regime in Kazakhstan. The components are the following: accounting, export and import control and physical protection of nuclear materials. First, the implementation of the goals of accounting and control bring into force, by the organization of the system for accounting and measurement of nuclear materials to determine present quantity. Organizing the accounting for nuclear material at facilities will ensure the efficiency of accountancy and reporting information. This defines the effectiveness of the state system for the accounting for the Kazakhstan's nuclear materials. Currently, Kazakhstan's nuclear material is fully safeguarded in designated secure locations. Kazakhstan has a nuclear power plant, 4 research reactors and a fuel fabrication plant. The governmental information system for nuclear materials control consist of two level: Governmental level - KAEA collects reports from facilities and prepares the reports for International Atomic Energy Agency, keeping of supporting documents and other necessary information, a data base of export and import, a data base of nuclear material inventory. Facility level - registration and processing information from key measurement points, formation the facility's nuclear materials accounting database. All facilities have computerized systems. Currently, all facilities are safeguarded under IAEA safeguarding standards, through IAEA inspections. Annually, IAEA verifies all nuclear materials at all Kazakhstan nuclear facilities. The government reporting system discloses the existence of all nuclear material and its transfer intended for interaction through the export control system and the nuclear control accounting system. Nuclear material export is regulated by the regulations of the Nuclear Export Control Law. The standard operating procedure is the primary means for

OPEN AND DISTANCE LEARNING: An Emerging System for Alternative Higher Education in Nigeria

Directory of Open Access Journals (Sweden)

Emmanuel Chisa IBARA

2008-01-01

Full Text Available ABSTRACT Nigeria no doubt is at the threshold of transformation in information and communication technology (ICT, a development that should be utilized to meet the demand of time, especially in the education sector. One area in which ICT has made enormous impact is in open and distance learning. Undoubtedly, the demand on the conventional higher education delivery system in the country is high and ever increasing that the system at the moment is unable to accommodate the number of candidates seeking admission. This paper, therefore, attempts some definition of open and distance learning as well as its practices with a view to advancing the prospects of open and distance as alternative system of higher education in Nigeria. Furthermore, it concludes that considering the level of infrastructural decay in the conventional higher education system, open and distance learning as an alternative system of education has become imperative for the realization of the primary objectives of higher education in Nigeria. Recommendations that will enhance the prospects of open and distance learning as viable alternative system of higher education were proffered.

Alternative approaches for identifying acute systemic toxicity: Moving from research to regulatory testing.

Science.gov (United States)

Hamm, Jon; Sullivan, Kristie; Clippinger, Amy J; Strickland, Judy; Bell, Shannon; Bhhatarai, Barun; Blaauboer, Bas; Casey, Warren; Dorman, David; Forsby, Anna; Garcia-Reyero, Natàlia; Gehen, Sean; Graepel, Rabea; Hotchkiss, Jon; Lowit, Anna; Matheson, Joanna; Reaves, Elissa; Scarano, Louis; Sprankle, Catherine; Tunkel, Jay; Wilson, Dan; Xia, Menghang; Zhu, Hao; Allen, David

2017-06-01

Acute systemic toxicity testing provides the basis for hazard labeling and risk management of chemicals. A number of international efforts have been directed at identifying non-animal alternatives for in vivo acute systemic toxicity tests. A September 2015 workshop, Alternative Approaches for Identifying Acute Systemic Toxicity: Moving from Research to Regulatory Testing, reviewed the state-of-the-science of non-animal alternatives for this testing and explored ways to facilitate implementation of alternatives. Workshop attendees included representatives from international regulatory agencies, academia, nongovernmental organizations, and industry. Resources identified as necessary for meaningful progress in implementing alternatives included compiling and making available high-quality reference data, training on use and interpretation of in vitro and in silico approaches, and global harmonization of testing requirements. Attendees particularly noted the need to characterize variability in reference data to evaluate new approaches. They also noted the importance of understanding the mechanisms of acute toxicity, which could be facilitated by the development of adverse outcome pathways. Workshop breakout groups explored different approaches to reducing or replacing animal use for acute toxicity testing, with each group crafting a roadmap and strategy to accomplish near-term progress. The workshop steering committee has organized efforts to implement the recommendations of the workshop participants. Copyright © 2017 Elsevier Ltd. All rights reserved.

Intelligent Materials Tracking System for Construction Projects Management

Directory of Open Access Journals (Sweden)

Narimah Kasim

2015-05-01

Full Text Available An essential factor adversely affecting the performance of construction projects is the improper handling of materials during site activities. In addition, paper-based reports are mostly used to record and exchange information related to the material components within the supply chain, which is problematic and inefficient. Generally, technologies (such as wireless systems and RFID are not being adequately used to overcome human errors and are not well integrated with project management systems to make tracking and management of materials easier and faster. Findings from a literature review and surveys showed that there is a lack of positive examples of such tools having been used effectively. Therefore, this research focused on the development of a materials tracking system that integrates RFID-based materials management with resources modelling to improve on-site materials tracking. Rapid prototyping was used to develop the system and testing of the system was carried out to examine the functionality and working appropriately. The proposed system is intended to promote the employment of RFID for automatic materials tracking with integration of resource modelling (Microsoft (R Office Project in the project management system in order to establish which of the tagged components are required resources for certain project tasks. In conclusion, the system provides an automatic and easy tracking method for managing materials during materials delivery and inventory management processes in construction projects.

Wood fly ash used for nutrient compensation or as a construction material. Environmental impacts related to different management alternatives; Skogsbraensleaska som naeringsresurs eller konstruktionsmaterial. Miljoeeffekter av olika hanteringsalternativ

Energy Technology Data Exchange (ETDEWEB)

Olsson, Susanna; Kaerrman, Erik; Roennblom, Tobias; Erlandsson, Aasa (Ecoloop AB, Stockholm (Sweden))

2008-08-15

The Swedish Forest Agency recommends that wood ash should be recycled to forest land, if the ashes fulfil certain threshold values. But there is also an option to use the ashes as construction material in forest roads. In this project, an environmental systems analysis approach was developed in order to assess the environmental impact from different alternatives. Three alternatives were analysed for the handling of 1 tonnes wood ash (DM) generated at the municipality of Boraas in Sweden: 1) Spreading the ashes to forests, 2) Use the ashes as a construction material in roads and 3) disposal of the ashes. Both the recycling of wood ash on forests and use of the ash for road construction have benefits in terms of saving natural resources and energy compared to disposal on landfill. Forest-recycling is the most energy efficient alternative and saves most of the resources Zn, P and dolomite. The road construction as well as the landfill alternatives results in a net-removal of the heavy metals As, Cd and Pb from the forests in a 100-year perspective, assuming that the content of these substances in the recycled ash is the same as the amount removed through biomass harvesting. Critical parameters for the results were the assumption that nutrient compensation is needed if wood ashes not are used on forests and the system boundaries chosen for assessing the heavy metal leaching. If the nutrient compensation is not considered as necessary, the influence on the results of transports and maintenance increase. One possibility for further work is to use the developed method for various regions in Sweden. The local conditions vary between different regions in terms of ash production, need for nutrient compensation and potential to build gravel roads etc

Nuclear proliferation and civilian nuclear power: report of the nonproliferation alternative systems assessment program. Volume V. Economics and systems analysis

International Nuclear Information System (INIS)

1979-12-01

This NASAP assessment considers the economics of alternative nuclear reactor and fuel-cycle systems in the light of possible patterns of uranium supply and energy demand, as well as the economic implications of improving the proliferation resistance of the various systems. The assessment focuses on the costs of alternative nuclear technologies and the possible timing of their implementation, based on their economic attractiveness. The objectives of this assessment are to identify when economic incentives to deploy advanced nuclear power systems might exist, to estimate the costs of using technologies that would reduce the risk of proliferation, to assess the impact of major economic uncertainties on the transition to new technologies, and to compare the investments required for alternative systems

Banana production systems: identification of alternative systems for more sustainable production.

Science.gov (United States)

Bellamy, Angelina Sanderson

2013-04-01

Large-scale, monoculture production systems dependent on synthetic fertilizers and pesticides, increase yields, but are costly and have deleterious impacts on human health and the environment. This research investigates variations in banana production practices in Costa Rica, to identify alternative systems that combine high productivity and profitability, with reduced reliance on agrochemicals. Farm workers were observed during daily production activities; 39 banana producers and 8 extension workers/researchers were interviewed; and a review of field experiments conducted by the National Banana Corporation between 1997 and 2002 was made. Correspondence analysis showed that there is no structured variation in large-scale banana producers' practices, but two other banana production systems were identified: a small-scale organic system and a small-scale conventional coffee-banana intercropped system. Field-scale research may reveal ways that these practices can be scaled up to achieve a productive and profitable system producing high-quality export bananas with fewer or no pesticides.

Evaluation of the odour reduction potential of alternative cover materials at a commercial landfill.

Science.gov (United States)

Solan, P J; Dodd, V A; Curran, T P

2010-02-01

The availability of virgin soils and traditional landfill covers are not only costly and increasingly becoming scarce, but they also reduce the storage capacity of landfill. The problem can be overcome by the utilisation of certain suitable waste streams as alternative landfill covers. The objective of this study was to assess the suitability of Construction & Demolition fines (C&D), Commercial & Industrial fines (C&I) and woodchip (WC) as potential landfill cover materials in terms of odour control. Background odour analysis was conducted to determine if any residual odour was emitted from the cover types. It was deemed negligible for the three materials. The odour reduction performance of each of the materials was also examined on an area of an active landfill site. A range of intermediate cover compositions were also studied to assess their performance. Odour emissions were sampled using a Jiang hood and analysed. Results indicate that the 200 mm deep combination layer of C&D and wood chip used on-site is adequate for odour abatement. The application of daily cover was found to result in effective reduction allowing for the background odour of woodchip.

Discussion of ALTERNATIVE systems for industrial radiography using X-ray films

International Nuclear Information System (INIS)

Vaessen B.; Perdieus, P.; Proegler, H.

1995-01-01

Industrial radiography using X-ray films is an established method of NDE. In the last few years, ''novel developments'' have been put on the market as ''alternatives'' to conventional radiography, as e.g. fluorescent screen/film systems, cost-saving films, wide-latitude films, and storage phosphor films. AGFA as a market leader in the sector of X-ray films for industrial radiography has been testing these alternatives, taking into account image quality, sensitivity, handling in terms of portability, reliability, and the essential functions for NDE: (1) Detection of X-radiation; (2) conversion to optical image; (3) evaluation and validation; (4) documentation and archivation. The advantages and drawbacks, the information transfer capabilities, and the performance from the applications point of view are discussed primarily for fluorescent screen/film systems and storage phophor systems. (orig./MM) [de

FMDP Reactor Alternative Summary Report: Volume 3 - partially complete LWR alternative

International Nuclear Information System (INIS)

Greene, S.R.; Fisher, S.E.; Bevard, B.B.

1996-09-01

The Department of Energy Office of Fissile Materials Disposition (DOE/MD) initiated a detailed analysis activity to evaluate each of ten plutonium disposition alternatives that survived an initial screening process. This document, Volume 3 of a four volume report summarizes the results of these analyses for the partially complete LWR (PCLWR) reactor based plutonium disposition alternative

FMDP Reactor Alternative Summary Report: Volume 3 - partially complete LWR alternative

Energy Technology Data Exchange (ETDEWEB)

Greene, S.R.; Fisher, S.E.; Bevard, B.B. [and others

1996-09-01

The Department of Energy Office of Fissile Materials Disposition (DOE/MD) initiated a detailed analysis activity to evaluate each of ten plutonium disposition alternatives that survived an initial screening process. This document, Volume 3 of a four volume report summarizes the results of these analyses for the partially complete LWR (PCLWR) reactor based plutonium disposition alternative.

Alternative Transportation System Demand Estimation for Federal Land Management Agencies.

Science.gov (United States)

2011-09-30

Estimating travel demand for alternative transportation systems (ATS) is challenging in any context, but is even more daunting for Federal Land Management Agencies (FLMAs). Federal public land sites vary widely in their characteristics. Moreover, tra...

Information system revives materials management

International Nuclear Information System (INIS)

Hansen, T.

1995-01-01

Through a change in philosophy and the development of a new, more efficient information management system, Arizona Public Service Co. (APSW) has, in less than two years, reduced material and service costs by 10 percent. The utility plans to cut these costs form 1993 figures by 25 percent before 2000. The utility is breaking new ground with ongoing implementation of new business processes and the new Materials Logistics Information System (MLIS), which has been co-developed with Texas Instruments Software Division (TISD)

Development of radioactive materials inspection system

International Nuclear Information System (INIS)

Yang Lu; Wang Guobao; Chen Yuhua; Li Latu; Zhang Sujing

2005-01-01

Radioactive materials inspection system which is applied to inspect the horror activities of radioactive materials and its illegal transfer. The detector sections are made of highly stable and credible material. It has high sensitivity to radioactive materials. The inspect lowest limit of inspection is the 2-3 times to the background, the energy range is 30 keV-2.5 MeV and the response time is 0.5 s. Inspection message can be transmitted through wired or wireless web to implement remote control. The structure of the system is small, light and convenient. It is ideal for protecting society and public from the harm of the radiation. (authors)

Double Retort System for Materials Compatibility Testing

International Nuclear Information System (INIS)

V. Munne; EV Carelli

2006-01-01

With Naval Reactors (NR) approval of the Naval Reactors Prime Contractor Team (NRPCT) recommendation to develop a gas cooled reactor directly coupled to a Brayton power conversion system as the Space Nuclear Power Plant (SNPP) for Project Prometheus (References a and b) there was a need to investigate compatibility between the various materials to be used throughout the SNPP. Of particular interest was the transport of interstitial impurities from the nickel-base superalloys, which were leading candidates for most of the piping and turbine components to the refractory metal alloys planned for use in the reactor core. This kind of contamination has the potential to affect the lifetime of the core materials. This letter provides technical information regarding the assembly and operation of a double retort materials compatibility testing system and initial experimental results. The use of a double retort system to test materials compatibility through the transfer of impurities from a source to a sink material is described here. The system has independent temperature control for both materials and is far less complex than closed loops. The system is described in detail and the results of three experiments are presented

Alternative splicing: the pledge, the turn, and the prestige : The key role of alternative splicing in human biological systems.

Science.gov (United States)

Gallego-Paez, L M; Bordone, M C; Leote, A C; Saraiva-Agostinho, N; Ascensão-Ferreira, M; Barbosa-Morais, N L

2017-09-01

Alternative pre-mRNA splicing is a tightly controlled process conducted by the spliceosome, with the assistance of several regulators, resulting in the expression of different transcript isoforms from the same gene and increasing both transcriptome and proteome complexity. The differences between alternative isoforms may be subtle but enough to change the function or localization of the translated proteins. A fine control of the isoform balance is, therefore, needed throughout developmental stages and adult tissues or physiological conditions and it does not come as a surprise that several diseases are caused by its deregulation. In this review, we aim to bring the splicing machinery on stage and raise the curtain on its mechanisms and regulation throughout several systems and tissues of the human body, from neurodevelopment to the interactions with the human microbiome. We discuss, on one hand, the essential role of alternative splicing in assuring tissue function, diversity, and swiftness of response in these systems or tissues, and on the other hand, what goes wrong when its regulatory mechanisms fail. We also focus on the possibilities that splicing modulation therapies open for the future of personalized medicine, along with the leading techniques in this field. The final act of the spliceosome, however, is yet to be fully revealed, as more knowledge is needed regarding the complex regulatory network that coordinates alternative splicing and how its dysfunction leads to disease.

Thermodynamic comparison and efficiency enhancement mechanism of coal to alternative fuel systems

International Nuclear Information System (INIS)

Ji, Xiaozhou; Li, Sheng; Gao, Lin; Jin, Hongguang

2016-01-01

Highlights: • Energy and exergy analysis are presented to three coal-to-alternative-fuels systems. • Internal reasons for performance differences for different systems are disclosed. • The temperature and heat release of synthesis reactions are key to plant efficiency. • The distillation unit and purge gas recovery are important to efficiency enhancement. - Abstract: Coal to alternative fuels is an important path to enforce energy security and to provide clean energy. In this paper, we use exergy analysis and energy utilization diagram (EUD) methods to disclose the internal reasons for performance differences in typical coal to alternative fuel processes. ASPEN plus software is used to simulate the coal-based energy systems, and the simulation results are verified with engineering data. Results show that coal to substitute natural gas (SNG) process has a higher exergy efficiency of 56.56%, while the exergy efficiency of traditional coal to methanol process is 48.65%. It is indicated that three key factors impact the performance enhancement of coal to alternative fuel process: (1) whether the fuel is distillated, (2) the synthesis temperature and the amount of heat release from reactions, and (3) whether the chemical purge gases from synthesis and distillation units are recovered. Distillation unit is not recommended and synthesis at high temperature and with large heat release is preferable for coal to alternative fuel systems. Gasification is identified as the main source of exergy destruction, and thereby how to decrease its destruction is the key direction of plant efficiency improvement in the future. Also, decreasing the power consumption in air separation unit by seeking for advanced technologies, i.e. membrane, or using another kind of oxidant is another direction to improve plant performance.

Development of total medical material distribution management system.

Science.gov (United States)

Uto, Y; Kumamoto, I

1994-07-01

Since September 1992, attempts have been made at Kagoshima University Hospital to develop the Medical Material Distribution Management System which helps to realize optimal hospital management as a subsystem of the Total Hospital Information System of Kagoshima University (THINK). As this system has been established, it has become possible for us to have an accurate grasp of the flow and stock of medical materials at our hospital. Furthermore, since September 1993, the Medical Material Distribution Management System has been improved and the Total Medical Material Distribution Management System has been smoothly introduced into the site of clinical practice. This system enables automatic demands for fees for treatment with specific instruments and materials covered by health insurance. It was difficult to predict the effect of this system, because no similar system had been developed in Japan. However, more satisfactory results than expected have been obtained since its introduction.

Optimal interface between principal deterrent systems and material accounting

International Nuclear Information System (INIS)

Deiermann, P.J.; Opelka, J.H.

1983-01-01

The purpose of this study is to find an optimal blend between three safeguards systems for special nuclear material (SNM), the material accounting system and the physical security and material control systems. The latter two are denoted as principal deterrent systems. The optimization methodology employed is a two-stage decision algorithm, first an explicit maximization of expected diverter benefits and subsequently a minimization of expected defender costs for changes in material accounting procedures and incremental improvements in the principal deterrent systems. The probability of diverter success function dependent upon the principal deterrents and material accounting system variables is developed. Within the range of certainty of the model, existing material accounting, material control and physical security practices are justified

Micro-Tom Tomato as an Alternative Plant Model System: Mutant Collection and Efficient Transformation.

Science.gov (United States)

Shikata, Masahito; Ezura, Hiroshi

2016-01-01

Tomato is a model plant for fruit development, a unique feature that classical model plants such as Arabidopsis and rice do not have. The tomato genome was sequenced in 2012 and tomato is becoming very popular as an alternative system for plant research. Among many varieties of tomato, Micro-Tom has been recognized as a model cultivar for tomato research because it shares some key advantages with Arabidopsis including its small size, short life cycle, and capacity to grow under fluorescent lights at a high density. Mutants and transgenic plants are essential materials for functional genomics research, and therefore, the availability of mutant resources and methods for genetic transformation are key tools to facilitate tomato research. Here, we introduce the Micro-Tom mutant database "TOMATOMA" and an efficient transformation protocol for Micro-Tom.

Refractories materials characterization for aluminum melting and holding furnaces: an alternative for a better performance

International Nuclear Information System (INIS)

Novo, M.M.M.; Pandolfelli, V.C.

2011-01-01

The industrial needs in reducing the energy consumption is part of a continuing search towards higher levels of sustainability and competitiveness. Considering these aspects, the aluminum industry seeks new alternatives for a better performance of aluminum melting and holding furnaces and this aim is directly dependent on the refractory materials ability to conserve heat and withstand the mechanical, chemical and thermal degradation processes. This paper presents the thermo-mechanical characterization of five aluminous dense commercial refractory (average density of 2.7 g / cm ³), used in such equipment. The results indicated that choosing the most suitable composition requires the evaluation of the microstructure aspects, such as porosity, permeability and pore size, and also the refractory's physical integrity, such as thermal shock resistance, abrasion resistance and high temperature modulus of rupture. The laboratory tests allowed the characterization of all the materials at the same conditions. Moreover, it was possible to optimize the selection of lining materials for melting and holding furnaces and to provide basis to a possible costs improvements synergy. (author)

Reactive transport modelling of groundwater-bentonite interaction: Effects on exchangeable cations in an alternative buffer material in-situ test

International Nuclear Information System (INIS)

Wallis, I.; Idiart, A.; Dohrmann, R.; Post, V.

2016-01-01

Bentonite clays are regarded a promising material for engineered barrier systems for the encapsulation of hazardous wastes because of their low hydraulic permeability, swelling potential, ability to self-seal cracks in contact with water and their high sorption potential. SKB (Svensk Kärnbränslehantering) has been conducting long term field scale experiments on potential buffer materials at the Äspö Hard Rock Laboratory for radioactive waste disposal in Sweden. The Alternative Buffer Material (ABM) test examined buffer properties of eleven different clay materials under the influence of groundwater and at temperatures reaching up to 135 °C, replicating the heat pulse after waste emplacement. Clay materials were emplaced into holes drilled in fractured granite as compacted rings around a central heater element and subsequently brought into contact with groundwater for 880 days. After test termination, and against expectations, all clay materials were found to have undergone large scale alterations in the cation exchange population. A reactive-diffusive transport model was developed to aid the interpretation of the observed large-scale porewater chemistry changes. It was found, that the interaction between Äspö groundwater and the clay blocks, together with the geochemical nature of the clays (Na vs Ca-dominated clays) exerted the strongest control on the porewater chemistry. A pronounced exchange of Na by Ca was observed and simulated, driven by large Ca concentrations in the contacting groundwater. The model was able to link the porewater alterations to the fracture network in the deposition hole. The speed of alterations was in turn linked to high diffusion coefficients under the applied temperatures, which facilitated the propagation of hydrochemical changes into the clays. With diffusion coefficients increased by up to one order of magnitude at the maximum temperatures, the study was able to demonstrate the importance of considering temperature

FMDP Reactor Alternative Summary Report: Volume 2 - CANDU heavy water reactor alternative

International Nuclear Information System (INIS)

Greene, S.R.; Spellman, D.J.; Bevard, B.B.

1996-09-01

The Department of Energy Office of Fissile Materials Disposition (DOE/MD) initiated a detailed analysis activity to evaluate each of ten plutonium disposition alternatives that survived an initial screening process. This document, Volume 2 of a four volume report, summarizes the results of these analyses for the CANDU reactor based plutonium disposition alternative

FMDP Reactor Alternative Summary Report: Volume 2 - CANDU heavy water reactor alternative

Energy Technology Data Exchange (ETDEWEB)

Greene, S.R.; Spellman, D.J.; Bevard, B.B. [and others

1996-09-01

The Department of Energy Office of Fissile Materials Disposition (DOE/MD) initiated a detailed analysis activity to evaluate each of ten plutonium disposition alternatives that survived an initial screening process. This document, Volume 2 of a four volume report, summarizes the results of these analyses for the CANDU reactor based plutonium disposition alternative.

Some considerations in the evaluation of concrete as a structural material for alternative LLW disposal technologies

International Nuclear Information System (INIS)

MacKenzie, D.R.; Siskind, B.; Bowerman, B.S.; Piciulo, P.L.

1987-01-01

The objective of this study was to develop information needed to evaluate the long-term performance of concrete and reinforced concrete as a structural material for alternative LLW disposal methods. The capability to carry out such an evaluation is required for licensing a site which employs one of these alternative methods. The basis for achieving the study objective was the review and analysis of the literature on concrete and its properties, particularly its durability. In carrying out this program characteristics of concrete useful in evaluating its performance and factors that can affect its performance were identified. The factors are both intrinsic, i.e., associated with composition of the concrete (and thus controllable), and extrinsic, i.e., due to external environmental forces such as climatic conditions and aggressive chemicals in the soil. The testing of concrete, using both accelerated tests and long-term non-accelerated tests, is discussed with special reference to its application to modeling of long-term performance prediction. On the basis of the study's results, conditions for acceptance are recommended as an aid in the licensing of disposal sites which make use of alternative methods

Alternating copolymers and alternative device geometries for organic photovoltaics.

Science.gov (United States)

Inganäs, Olle; Zhang, Fengling; Andersson, Mats R

2012-01-01

The efficiency of conversion of light to electrical energy with the help of conjugated polymers and molecules is rapidly improving. The optical absorption properties of these materials can be designed, and implemented via molecular engineering. Full coverage of the solar spectrum is thus feasible. Narrow absorption spectra allow construction of tandem solar cells. The poor transport properties of these materials require thin devices, which limits optical absorption. Alternative device geometries for these flexible materials compensate for the optical absorption by light trapping, and allow tandem cells.

Financing alternatives and incentives for solar-thermal central-receiver systems

Energy Technology Data Exchange (ETDEWEB)

Bos, P.B.

1982-07-01

As a result of various recently enacted incentive and regulatory legislation combined with the new administration policy and budgetary guidelines, the commercialization of solar thermal central receiver systems will involve financing alternatives other than conventional utility financing. This study was conducted to identify these potential financing alternatives and the associated requirements and impacts on the Department of Energy program. Based upon this analysis, it is concluded that the current alternative financing window is extremely short (through 1985), and that an extension or at the least a gradual phasing out, of the solar tax credits is necessary for the successful transfer of the central receiver technology to the private sector. Furthermore, throughout this time period, continued government support of the R and D activities is necessary to provide the necessary confidence in this technology for the private (financial) sector to underwrite this technology transfer. Consequently, even though the central receiver technology shows high promise for replacing a significant fraction of the oil/gas-fired utility industry peaking and intermediate generation, the current readiness status of this technology still requires further direct and indirect government support for a successful technology transfer. The direct government research and development support will provide the basis for a technological readiness and confidence, whereas the indirect tax incentive support serves to underwrite the extraordinary risks associated with the technology transfer. These support requirements need only be limited to and decreasing during this technology transfer phase, since as the systems approach successful full-scale commercialization, the extraordinary risks will be gradually eliminated. At the time of commercialization the system's value should be on a par with the installed system's cost.

Computerized reactor pressure vessel materials information system

International Nuclear Information System (INIS)

Strosnider, J.; Monserrate, C.; Kenworthy, L.D.; Tether, C.D.

1980-10-01

A computerized information system for storage and retrieval of reactor pressure vessel materials data was established, as part of Task Action Plan A-11, Reactor Vessel Materials Toughness. Data stored in the system are necessary for evaluating the resistance of reactor pressure vessels to flaw-induced fracture. This report includes (1) a description of the information system; (2) guidance on accessing the system; and (3) a user's manual for the system

Evaluation of alternative public transportation systems in Izmit urban transportation via axiomatic design method

Directory of Open Access Journals (Sweden)

Gülşen AKMAN

2016-02-01

Full Text Available In the world and in our country, most of urban transportation is performed by public transportation. Public transportation is a system which provides transportation easiness and opportunity to people, not to vehicles. Therefore, giving priority to public transportation system is necessary in organizing urban transportation. In this study, in order to reduce traffic intensity and to facilitate passenger transportation in Izmit urban transportation, It is tried to determine appropriate public transportation system. For this, firstly, alternatives which could be used for public transportation were determined. These alternatives are metro, metrobus, tram, light rail system and monorail. Afterwards, the variables affecting decision making about public transportation were determined. These variables are cost, transportation line features, vehicle characteristics, sensitivity to environment and customer satisfaction. Lastly, most appropriate public transportation system is proposed by using the axiomatic design method. As a result, light trail system and metrobus are determined as the most appropriate alternatives for Izmit public transportation system.Keywords: Urban transportation, Multi criteria decision making, Axiomatic design

Estimated routine radiation doses to transportation workers in alternative spent-fuel transportation systems

International Nuclear Information System (INIS)

Schneider, K.J.; Smith, R.I.; Daling, P.M.; Ross, W.A.; McNair, G.W.

1988-01-01

The federal system for the management of spent fuel and high-level radioactive waste includes the acceptance by the US Department of Energy (DOE) of the spent fuel or waste loaded in casks at the reactor or other waste generators, its transportation to a repository, and its handling and final emplacement in the repository. The DOE plans to implement a transportation system that is safe, secure, efficient, and cost-effective and will meet applicable regulatory safety and security requirements. The DOE commissioned the Pacific Northwest Laboratory (PNL) to develop estimates of the routine radiation doses that would result from the operation of a system postulated using current designs and practices. From that evaluation, PNL identified activities/operations that result in the higher fraction of doses, proposed conceptual alternatives that would effectively reduce such exposures, and evaluated the cost-effectiveness of such alternatives. The study is one of a series used in making overall system design and operational decisions in the development of the DOE's spent-fuel/high-level waste transportation system. This paper contains the highlights from the PNL study of the estimated radiation doses to the transportation workers in a postulated reference transportation system and potential alternatives to that system

Alternative fuels, fuel cycles, and reactors: are they useful. are they necessary

International Nuclear Information System (INIS)

Spinrad, B.I.

1985-01-01

This chapter discusses reactors, fuel cycles, and fuel production concepts other than those considered conventional in the nuclear community. An attempt is made to look for improvements with the aim of providing cheaper and more durable energy systems, and to contribute toward a solution of the threat of weapons material diversion and weapons proliferation problems. Topics considered include breeding, alternate breeder cycles, alternative reprocessing schemes, symbiotic reactor systems, an interim strategy, and other sources of nuclear fuel. It is determined that the reprocessing of spent fuel is an important safeguard measure in itself

Depleted uranium management alternatives

Energy Technology Data Exchange (ETDEWEB)

Hertzler, T.J.; Nishimoto, D.D.

1994-08-01

This report evaluates two management alternatives for Department of Energy depleted uranium: continued storage as uranium hexafluoride, and conversion to uranium metal and fabrication to shielding for spent nuclear fuel containers. The results will be used to compare the costs with other alternatives, such as disposal. Cost estimates for the continued storage alternative are based on a life-cycle of 27 years through the year 2020. Cost estimates for the recycle alternative are based on existing conversion process costs and Capital costs for fabricating the containers. Additionally, the recycle alternative accounts for costs associated with intermediate product resale and secondary waste disposal for materials generated during the conversion process.

Depleted uranium management alternatives

International Nuclear Information System (INIS)

Hertzler, T.J.; Nishimoto, D.D.

1994-08-01

This report evaluates two management alternatives for Department of Energy depleted uranium: continued storage as uranium hexafluoride, and conversion to uranium metal and fabrication to shielding for spent nuclear fuel containers. The results will be used to compare the costs with other alternatives, such as disposal. Cost estimates for the continued storage alternative are based on a life-cycle of 27 years through the year 2020. Cost estimates for the recycle alternative are based on existing conversion process costs and Capital costs for fabricating the containers. Additionally, the recycle alternative accounts for costs associated with intermediate product resale and secondary waste disposal for materials generated during the conversion process

The Use of Reactive Materials in Septic Systems for Pathogens and Nitrate Removal

Science.gov (United States)

Suhogusoff, A. V.; Hirata, R.; Aravena, R.; Stimson, J.; Robertson, W.

2009-05-01

The developing countries have an urgent need for cheap and efficient techniques for the improvement of sanitary conditions in areas without public water supply and sewerage system, especially in suburban regions or irregular occupation areas, where there is a great lack of social assistance. In this type of situations, the inhabitants use dug wells for water use and cesspits for disposal of sewage, which usually contaminates the groundwater with nitrate and microorganisms. As part of a study aiming to develop new sewage treatment systems in an irregular occupation area located at the District of Barragem, south region of the municipality of São Paulo (Brazil), a conventional cesspit (named as "Control") and an alternative septic system were constructed and monitored for a year. The design of the alternative septic system included a 1m thickness reactive barrier constituted by BOF (Budget Oxygen Furnace - a byproduct of the steel-making industry) for pathogens removal, then 1m sand package where the wastewater is oxidized and at the bottom the wastewater is in contact with a 0,5m thickness reactive barrier constituted by sawdust (carbon source), where redox conditions are very reducing and denitrification and even methanogenesis can take place. The chemical and biological data collected in the alternative septic system showed complete removal of the pathogens in the BOF barrier, then nitrification occurred between the BOF and the bottom of sand package. However denitrification in the sawdust barrier was incomplete because of the high pH caused by the BOF materials, which can reduced the number of denitrifiers bacteria present in the sawdust barrier. Isotope analyses that are been carried out in the residual nitrate will provided more information about the extent of the denitrification reaction in the alternative septic system. In case of the control cesspit, it was observed the occurrence of high concentration of ammonium, dissolved organic carbon, CO2, CH4 and low

Alternative Plasmonic Materials: Beyond Gold and Silver

DEFF Research Database (Denmark)

Naik, Gururaj V.; Shalaev, Vladimir M.; Boltasseva, Alexandra

2013-01-01

Materials research plays a vital role in transforming breakthrough scientific ideas into next‐generation technology. Similar to the way silicon revolutionized the microelectronics industry, the proper materials can greatly impact the field of plasmonics and metamaterials. Currently, research...... such as gold and silver, that exhibit metallic properties and provide advantages in device performance, design flexibility, fabrication, integration, and tunability. This review explores different material classes for plasmonic and metamaterial applications, such as conventional semiconductors, transparent...

Mathematical Methods of System Analysis in Construction Materials

Science.gov (United States)

Garkina, Irina; Danilov, Alexander

2017-10-01

System attributes of construction materials are defined: complexity of an object, integrity of set of elements, existence of essential, stable relations between elements defining integrative properties of system, existence of structure, etc. On the basis of cognitive modelling (intensive and extensive properties; the operating parameters) materials (as difficult systems) and creation of the cognitive map the hierarchical modular structure of criteria of quality is under construction. It actually is a basis for preparation of the specification on development of material (the required organization and properties). Proceeding from a modern paradigm (model of statement of problems and their decisions) of development of materials, levels and modules are specified in structure of material. It when using the principles of the system analysis allows to considered technological process as the difficult system consisting of elements of the distinguished specification level: from atomic before separate process. Each element of system depending on an effective objective is considered as separate system with more detailed levels of decomposition. Among them, semantic and qualitative analyses of an object (are considered a research objective, decomposition levels, separate elements and communications between them come to light). Further formalization of the available knowledge in the form of mathematical models (structural identification) is carried out; communications between input and output parameters (parametrical identification) are defined. Hierarchical structures of criteria of quality are under construction for each allocated level. On her the relevant hierarchical structures of system (material) are under construction. Regularities of structurization and formation of properties, generally are considered at the levels from micro to a macrostructure. The mathematical model of material is represented as set of the models corresponding to private criteria by which separate

Transparent Façade Panel Typologies Based on Recyclable Polymer Materials

Directory of Open Access Journals (Sweden)

Harry Giles

2012-11-01

Full Text Available Buildings are large consumers of energy. In the United States of America; they constitute over 33% of the total annual energy consumption, produce 35% of the total carbon dioxide emissions and attribute 40% of landfill wastes. The building industry is also a large consumer of non-renewable materials and this trend has escalated dramatically over the past century. It is essential that we find ways to save on energy consumption through the use of solar energy, improved thermal insulation, and alternative efficient glazed façade systems. In this paper, we demonstrate how alternative typologies of transparent and translucent load-bearing façade systems based on biocomposite and recyclable materials, are structurally and thermally efficient at the same time they contribute towards reduced pollutant emissions and non-renewable material uses.Composite insulated panel systems are used extensively in the engineering and building industry, owing to their structural and thermal efficiency. However, these systems are generally opaque and offer little flexibility in building applications. As an alternative, we demonstrate how building products comprised of hybrid material typologie scan be made to perform efficiently as load-bearing façade systems that substitute for current glazing systems with adequate thermal and structural performance, which also possess good light transmission characteristics and integral shading capability. The materials are configured to work as composite panel systems made from a combination of biocomposite and recyclable polymer materials. These materials are environmentally sustainable, because they either originate from naturally grown renewable resources or are recyclable. Our research program includes the design and development of prototype panel systems; the evaluation of structural and thermal performance, together with their role in reducing energy consumption and pollution emission through life cycle analysis. The paper

Armor systems including coated core materials

Science.gov (United States)

Chu, Henry S [Idaho Falls, ID; Lillo, Thomas M [Idaho Falls, ID; McHugh, Kevin M [Idaho Falls, ID

2012-07-31

An armor system and method involves providing a core material and a stream of atomized coating material that comprises a liquid fraction and a solid fraction. An initial layer is deposited on the core material by positioning the core material in the stream of atomized coating material wherein the solid fraction of the stream of atomized coating material is less than the liquid fraction of the stream of atomized coating material on a weight basis. An outer layer is then deposited on the initial layer by positioning the core material in the stream of atomized coating material wherein the solid fraction of the stream of atomized coating material is greater than the liquid fraction of the stream of atomized coating material on a weight basis.

Assessment of comparative and non-comparative factors in alternate energy system

Energy Technology Data Exchange (ETDEWEB)

Rowe, W D; Oterson, P

1983-01-01

The American University Institute for Risk Analysis (AURA) has undertaken a study for the European Economic Community to critically evaluate the methodologies for comparative risk analyses and costs and benefits of alternative energy systems used to generate electricity, principally nuclear, coal, and oil. Other energy systems and related industries with major hazards are also addressed where pertinent. This is particularly true for cases where electrical energy may be an inefficient form for end use as for transportation and space heating. Here, comparison on an end use basis by the most efficient method, electrical or otherwise, is required. The starting point and basis for this evaluation has been the array of existing studies of alternative energy systems already published. These studies, including those already undertaken by the Community, are over 50 in number. The purpose of this study is not to make a comparison of alternative energy systems, but to evaluate what is and what is not useful in existing studies, as well as to provide insight on how meaningful studies can be conducted. There has been considerable criticism and discussion about the conduct and validity of several studies, particularly the Inhaber study and the critiques of Holdren et al. While much of the critiques deal with methods and approaches, substantial criticism and discussion has focused on the motivations of the investigators and how the studies were applied. This latter set of issues is hardly a technological or methodological argument.

Comparing two types of augmentative and alternative communication systems for children with autism.

Science.gov (United States)

Son, Seung-Hyun; Sigafoos, Jeff; O'Reilly, Mark; Lancioni, Giulio E

2006-01-01

This study compared acquisition and preference for two types of augmentative and alternative communication (AAC) systems in three pre-schoolers with autism. Acquisition of requesting behaviour using a picture-exchange system vs a voice-output communication aide (VOCA) was compared in an alternating treatments design. Following acquisition, both ACC systems were simultaneously available and the child could select which one of the two systems to use. There was little difference between picture-exchange and VOCA in terms of acquisition rates. Two children demonstrated a consistent preference for picture-exchange and the third showed a preference for the VOCA. Both speed of acquisition and system preference should be considered when designing AAC interventions for children with autism and related developmental disabilities.

Perfluorocyclobutane containing aromatic ether polymers as planarization materials for alternative magnetic media substrates

Science.gov (United States)

Perettie, Donald J.; Judy, Jack; Chen, Qixu; Keirstead, Rick

1994-11-01

Perfluorocyclobutane aromatic ether polymers (PFCB) are being researched as planarization materials for alternative magnetic media substrates allowing smoother surfaces for lower head flying recording. The results of current work reported herein have shown that PFCB can be used to affect surfaces on canasite with R(sub A)'s less than 2 nm. In addition, magnetic media can be produced of a quality comparative to that obtained on standard NiP-coated Al as well as that produced on regular canasite with equivalent coercivities at about 1500-1600 Oe and squarenesses of 0.8 or better. In addition to the above magnetic properties the recording performance was excellent with signal-to-noise ratios of planarized media 3.5 dB higher than that on regular canasite.

Alternating Copolymers and Alternative Device Geometries for Organic Photovoltaics

OpenAIRE

Inganäs, Olle; Zhang, Fengling; Andersson, Mats R.

2012-01-01

The efficiency of conversion of light to electrical energy with the help of conjugated polymers and molecules is rapidly improving. The optical absorption properties of these materials can be designed, and implemented via molecular engineering. Full coverage of the solar spectrum is thus feasible. Narrow absorption spectra allow construction of tandem solar cells. The poor transport properties of these materials require thin devices, which limits optical absorption. Alternative device geometr...

Alternative free volume models and positron cages for the characterisation of nanoporosity in materials

International Nuclear Information System (INIS)

Felix, M.V.; Morones, R.; Castano, V.M.

2004-01-01

Three semi-empirical positron stationary Quantum Models were developed for the study of nanoporosity in a wide range of solid porous materials. The cubic, conic and cylindrical well potentials were considered and their geometric parameters related to the Positron Annihilation LifeTime (PALT) measurements. If a conic or a cubic symmetry is assumed, a resonance lifetime phenomenon was found, which enables proposal of a technique to catch positrons in free volume sites. In the cylindrical case, an alternative method to determine free volume sizes in materials was developed. The free volume equations of these new models were then compared to the well-known and widely utilised Spherical Free Volume Model (SFVM) and remarkable differences were found. A strong variation of the free volume size-positron lifetime relation with the geometry involved was observed and a remarkable dependence of the electron layer thickness parameter ΔR with the hole-shape under study and with the nature of the material considered. The mathematical functions appearing in the conic and cylindrical cases are the superposition of Bessel functions of the first kind and trigonometric functions in the cubic case. Generalised free volume diagrams were constructed and a brief geometrical scheme of the diverse cases considered was obtained. (author)

On Using Materiality in Information Systems Development

DEFF Research Database (Denmark)

Carugati, Andrea

This research brief presents a discussion on the use of the concept of materiality and material knowing in information systems development (ISD). The discussion addresses some of the practical problems still plaguing ISD, augmenting existing ISD methodologies with contributions from systems theory...... as scaffold of knowledge. Through the example taken from a case study of a complex and innovative systems development we outline two design principles to be embedded in modular fashion in ISD processes: (1) whenever possible start ISD efforts by developing a graphical simulator of the material environment...

Modification of alternative additives and their effect on the rubber properties

Directory of Open Access Journals (Sweden)

Ondrušová Darina

2018-01-01

Full Text Available The present paper deals with a targeted modification of two kinds of alternative additives - waste from glass production and natural mineral filler and explores their effect on the properties of polymeric materials. In the function of first alternative filler was used sludge from weighing the ingredients of glass batch in the glass production. The second used was natural aluminosilicate material based on zeolite (clinoptilolite. These alternative fillers have been modified in order to increase its efficiency, using the silanes: 3-aminopropyl-triethoxysilane, bis(triethoxysilylpropyl-tetrasulfide and 3-(triethoxysilylpropyl-methacrylate. In the case of alternative filler based on zeolite the influence of silanization conditions on the filler efficiency have been also studied. Prepared modified fillers were mixed into rubber compounds as partial replacement of commonly used filler – carbon black. The influence of prepared fillers on rheology and curing characteristics of rubber compounds and also on physical and mechanical properties of vulcanizates has been studied. Obtained results of measured characteristics of polymeric systems containing prepared alternative fillers were compared with the results obtained in the case of reference rubber compound with a commertially used filler – carbon black.

STAGES : a system for generating strategic alternatives for forest management

NARCIS (Netherlands)

Bos, J.

1994-01-01

Strategic planning is important in forest management. However, it has never been described clearly in literature. In this study a framework for strategic planning was developed and based on this a STrategic Alternatives Generating System (STAGES) to support decision making in strategic

High Power Alternator Test Unit (ATU) Electrical System Test

Science.gov (United States)

Birchenough, Arthur; Hervol, David

2007-01-01

The Alternator Test Unit (ATU) in the Lunar Power System Facility (LPSF) located at the NASA Glenn Research Center (GRC) in Cleveland, OH was used to simulate the operating conditions and evaluate the performance of the ATU and it s interaction with various LPSF components in accordance with the JIMO AC Power System Requirements. The testing was carried out at the breadboard development level. Results of these tests will be used for the development and validation of analytical models for performance and lifetime prediction.

Development of the Model of Decision Support for Alternative Choice in the Transportation Transit System

Directory of Open Access Journals (Sweden)

Kabashkin Igor

2015-02-01

Full Text Available The decision support system is one of the instruments for choosing the most effective decision for cargo owner in constant fluctuated business environment. The objective of this Paper is to suggest the multiple-criteria approach for evaluation and choice the alternatives of cargo transportation in the large scale transportation transit system for the decision makers - cargo owners. The large scale transportation transit system is presented by directed finite graph. Each of 57 alternatives is represented by the set of key performance indicators Kvi and set of parameters Paj. There has been developed a two-level hierarchy system of criteria with ranging expert evaluations based on Analytic Hierarchy Process Method. The best alternatives were suggested according to this method.

U.S. national nuclear material control and accounting system

International Nuclear Information System (INIS)

Taylor, S; Terentiev, V G

1998-01-01

Issues related to nuclear material control and accounting and illegal dealing in these materials were discussed at the April 19--20, 1996 Moscow summit meeting (G7 + Russia). The declaration from this meeting reaffirmed that governments are responsible for the safety of all nuclear materials in their possession and for the effectiveness of the national control and accounting system for these materials. The Russian delegation at this meeting stated that ''the creation of a nuclear materials accounting, control, and physical protection system has become a government priority''. Therefore, in order to create a government nuclear material control and accounting system for the Russian Federation, it is critical to study the structure, operating principles, and regulations supporting the control and accounting of nuclear materials in the national systems of nuclear powers. In particular, Russian specialists have a definite interest in learning about the National Nuclear Material Control and Accounting System of the US, which has been operating successfully as an automated system since 1968

IMPROVING MODEL OF CHANNEL AIRBORN ELECTRICAL POWER SYSTEM OF ALTERNATING CURRENT

Directory of Open Access Journals (Sweden)

Yu. P. Artemenko

2015-01-01

Full Text Available This article is devoted to math modeling of channel of alternating current airborne electrical power-supply system. Mathematical modeling of generator, voltage regulator, constant speed drive is considered.

Use of time and materials and cost reimbursement subcontracts for remedial actions under the alternative remedial contracting strategy contracts. Directive

International Nuclear Information System (INIS)

1992-01-01

The directive is intended to establish agency guidance on the use of time and materials and cost reimbursement contracts for remedial actions in general and to provide specific instruction regarding the use of these approaches in subcontracting under the Alternative Remedial Contracting Strategy (ARCS) contracts

Nuclear proliferation and civilian nuclear power. Report of the Nonproliferation Alternative Systems Assessment Program. Volume V. Economics and systems analysis

International Nuclear Information System (INIS)

1980-06-01

This NASAP assessment considers the economics of alternative nuclear reactor and fuel-cycle systems in the light of possible patterns of uranium supply and energy demand, as well as the economic implications of improvng the proliferation resistance of the various systems. The assessment focuses on the costs of alternative nuclear technologies and the possible timing of their implementation, based on their economic attractiveness

Climate control systems using pozzolan materials

KAUST Repository

Almadhoun, Mahmoud Nassar Mahmoud

2016-02-18

A system and method for conditioning air is provided that optimizes the use of sustainable and locally sourced materials with agrarian, residential, and industrial applications. The system can be formed with a porous siliceous, or siliceous and aluminous material that is sufficiently porous, to allow conditioning fluid to flow there through. The material can also be formed into a structure that includes one or more passageways configured to allow air to be conditioned to also pass there through. The structure can be configured to cause the conditioning fluid passing through the porous portions of the structure to intersect and mix with air passing there through. The structure may include a plurality of passageways and intersections and may include a plurality of air inlets and outlets for air passage. The system may additionally include a means for storing, collecting, and driving conditioning fluid through the system and a means for collecting solar radiation to drive airflow and regenerate conditioning fluid.

Alternative High Performance Polymers for Ablative Thermal Protection Systems

Science.gov (United States)

Boghozian, Tane; Stackpoole, Mairead; Gonzales, Greg

2015-01-01

Ablative thermal protection systems are commonly used as protection from the intense heat during re-entry of a space vehicle and have been used successfully on many missions including Stardust and Mars Science Laboratory both of which used PICA - a phenolic based ablator. Historically, phenolic resin has served as the ablative polymer for many TPS systems. However, it has limitations in both processing and properties such as char yield, glass transition temperature and char stability. Therefore alternative high performance polymers are being considered including cyanate ester resin, polyimide, and polybenzoxazine. Thermal and mechanical properties of these resin systems were characterized and compared with phenolic resin.

Alternative kinetic energy metrics for Lagrangian systems

Science.gov (United States)

Sarlet, W.; Prince, G.

2010-11-01

We examine Lagrangian systems on \\ {R}^n with standard kinetic energy terms for the possibility of additional, alternative Lagrangians with kinetic energy metrics different to the Euclidean one. Using the techniques of the inverse problem in the calculus of variations we find necessary and sufficient conditions for the existence of such Lagrangians. We illustrate the problem in two and three dimensions with quadratic and cubic potentials. As an aside we show that the well-known anomalous Lagrangians for the Coulomb problem can be removed by switching on a magnetic field, providing an appealing resolution of the ambiguous quantizations of the hydrogen atom.

Alternative Raw Materials for Animal Feed

Directory of Open Access Journals (Sweden)

A R Alimon

2009-06-01

Full Text Available The increase in world fuel prices in the last few years has charged the global animal feedstuffs. In Malaysia, the feed industry is dependent on the importation of corn and soybean meal as the poultry and swine industries are almost totally based on corn soya bean meal diets. However, there are many byproducts and coproducts available in Malaysia as alternatives to corn or soy bean. Since Malaysia has more than 4 million hectares of oil palm plantation and after processing for the oil, large quantities of several byproducts are produced. This paper describes several available byproducts and co products in Malaysia, their nutritive value and their problems.

Parametric Optimization of Some Critical Operating System Functions--An Alternative Approach to the Study of Operating Systems Design

Science.gov (United States)

Sobh, Tarek M.; Tibrewal, Abhilasha

2006-01-01

Operating systems theory primarily concentrates on the optimal use of computing resources. This paper presents an alternative approach to teaching and studying operating systems design and concepts by way of parametrically optimizing critical operating system functions. Detailed examples of two critical operating systems functions using the…

Multicriteria Decision Analysis of Material Selection of High Energy Performance Residential Building

Science.gov (United States)

Čuláková, Monika; Vilčeková, Silvia; Katunská, Jana; Krídlová Burdová, Eva

2013-11-01

In world with limited amount of energy sources and with serious environmental pollution, interest in comparing the environmental embodied impacts of buildings using different structure systems and alternative building materials will be increased. This paper shows the significance of life cycle energy and carbon perspective and the material selection in reducing energy consumption and emissions production in the built environment. The study evaluates embodied environmental impacts of nearly zero energy residential structures. The environmental assessment uses framework of LCA within boundary: cradle to gate. Designed alternative scenarios of material compositions are also assessed in terms of energy effectiveness through selected thermal-physical parameters. This study uses multi-criteria decision analysis for making clearer selection between alternative scenarios. The results of MCDA show that alternative E from materials on nature plant base (wood, straw bales, massive wood panel) present possible way to sustainable perspective of nearly zero energy houses in Slovak republic

Aberrant and alternative splicing in skeletal system disease.

Science.gov (United States)

Fan, Xin; Tang, Liling

2013-10-01

The main function of skeletal system is to support the body and help movement. A variety of factors can lead to skeletal system disease, including age, exercise, and of course genetic makeup and expression. Pre-mRNA splicing plays a crucial role in gene expression, by creating multiple protein variants with different biological functions. The recent studies show that several skeletal system diseases are related to pre-mRNA splicing. This review focuses on the relationship between pre-mRNA splicing and skeletal system disease. On the one hand, splice site mutation that leads to aberrant splicing often causes genetic skeletal system disease, like COL1A1, SEDL and LRP5. On the other hand, alternative splicing without genomic mutation may generate some marker protein isoforms, for example, FN, VEGF and CD44. Therefore, understanding the relationship between pre-mRNA splicing and skeletal system disease will aid in uncovering the mechanism of disease and contribute to the future development of gene therapy. © 2013 Elsevier B.V. All rights reserved.

Systems and methods for treating material

Science.gov (United States)

Scheele, Randall D; McNamara, Bruce K

2014-10-21

Systems for treating material are provided that can include a vessel defining a volume, at least one conduit coupled to the vessel and in fluid communication with the vessel, material within the vessel, and NF.sub.3 material within the conduit. Methods for fluorinating material are provided that can include exposing the material to NF.sub.3 to fluorinate at least a portion of the material. Methods for separating components of material are also provided that can include exposing the material to NF.sub.3 to at least partially fluorinate a portion of the material, and separating at least one fluorinated component of the fluorinated portion from the material. The materials exposed to the NF.sub.3 material can include but are not limited to one or more of U, Ru, Rh, Mo, Tc, Np, Pu, Sb, Ag, Am, Sn, Zr, Cs, Th, and/or Rb.

Decision support tool to evaluate alternative policies regulating wind integration into autonomous energy systems

International Nuclear Information System (INIS)

Zouros, N.; Contaxis, G.C.; Kabouris, J.

2005-01-01

Integration of wind power into autonomous electricity systems strongly depends on the specific technical characteristics of these systems; the regulations applied should take into account physical system constraints. Introduction of market rules makes the issue even more complicated since the interests of the market participants often conflict each other. In this paper, an integrated tool for the comparative assessment of alternative regulatory policies is presented along with a methodology for decision-making, based on alternative scenarios analysis. The social welfare concept is followed instead of the traditional Least Cost Planning

Structural materials for innovative nuclear systems (SMINS)

International Nuclear Information System (INIS)

2008-01-01

Structural materials research is a field of growing relevance in the nuclear sector, especially for the different innovative reactor systems being developed within the Generation IV International Forum (GIF), for critical and subcritical transmutation systems, and of interest to the Global Nuclear Energy Partnership (GNEP). Under the auspices of the NEA Nuclear Science Committee (NSC) the Workshop on Structural Materials for Innovative Nuclear Systems (SMINS) was organised in collaboration with the Forschungszentrum Karlsruhe in Germany. The objectives of the workshop were to exchange information on structural materials research issues and to discuss ongoing programmes, both experimental and in the field of advanced modelling. These proceedings include the papers and the poster session materials presented at the workshop, representing the international state of the art in this domain. (author)

Alternative risk-based criteria for transportation of radioactive materials on the United States Department of Energy Hanford Site

International Nuclear Information System (INIS)

Mercado, J.E.; Field, J.G.; Smith, R.J.; Wang, O.S.

1993-01-01

This paper presents the development of an alternative method to evaluate packaging safety for radioactive material transported solely within the boundaries of a restricted site; the method uses risk-based criteria to assess and document packaging safety. These criteria offer a standard against which the results of a risk assessment are compared to evaluate the safety of a transportation operation. Numerous payloads are transported entirely within the U.S. Department of Energy's Hanford Site boundaries. The U.S. Department of Energy requires that the safety of onsite transportation be equivalent to the safety provided for transporting radioactive materials in commerce as regulated by the U.S. Department of Transportation and the U.S. Nuclear Regulatory Commission. Some onsite packaging configurations do not meet the performance criteria that form the basis of these regulations, necessitating the establishment of alternative criteria to evaluate safety. Quantitatively defined criteria have been derived from the U.S. Department of Transportation limits for package radiation levels, curie content, activity release, and external contamination levels. Recommendations of the International Committee on Radiation Protection may further restrict the criteria. The proposed method documents packaging safety in a transportation risk assessment. The assessment estimates accident frequencies, conservatively evaluates the dose consequences of these accidents, and compares the results to the established risk acceptance criteria. Specific Hanford Site onsite packaging and transportation issues illustrate the alternative method. The paper compares the solutions resulting from the application of risk-based criteria to those resulting from strict compliance with commercial transportation regulations. (author)

ALTERNATIVE MATERIALS TO PD MEMBRANES FOR HYDROGEN PURIFICATION

Energy Technology Data Exchange (ETDEWEB)

Korinko, P; T. Adams

2008-09-12

Development of advanced hydrogen separation membranes in support of hydrogen production processes such as coal gasification and as front end gas purifiers for fuel cell based system is paramount to the successful implementation of a national hydrogen economy. Current generation metallic hydrogen separation membranes are based on Pd-alloys. Although the technology has proven successful, at issue is the high cost of palladium. Evaluation of non-noble metal based dense metallic separation membranes is currently receiving national and international attention. The focal point of the reported work was to evaluate two different classes of materials for potential replacement of conventional Pd-alloy purification/diffuser membranes. Crystalline V-Ni-Ti and Amorphous Fe- and Co-based metallic glass alloys have been evaluated using gaseous hydrogen permeation testing techniques.

Integrated material accountancy system

International Nuclear Information System (INIS)

Calabozo, M.; Buiza, A.

1991-01-01

In this paper we present the system that we are actually using for Nuclear Material Accounting and Manufacturing Management in our UO 2 Fuel Fabrication Plant located at Juzbado, Salamanca, Spain. The system is based mainly on a real time data base which gather data for all the operations performed in our factory from UO 2 powder reception to fuel assemblies shipment to the customers. The accountancy is just an important part of the whole integrated system covering all the aspects related to manufacturing: planning, traceability, Q.C. analysis, production control and accounting data

Nonterrestrial material processing and manufacturing of large space systems

Science.gov (United States)

Von Tiesenhausen, G.

1979-01-01

Nonterrestrial processing of materials and manufacturing of large space system components from preprocessed lunar materials at a manufacturing site in space is described. Lunar materials mined and preprocessed at the lunar resource complex will be flown to the space manufacturing facility (SMF), where together with supplementary terrestrial materials, they will be final processed and fabricated into space communication systems, solar cell blankets, radio frequency generators, and electrical equipment. Satellite Power System (SPS) material requirements and lunar material availability and utilization are detailed, and the SMF processing, refining, fabricating facilities, material flow and manpower requirements are described.

Automated accounting systems for nuclear materials

International Nuclear Information System (INIS)

Erkkila, B.

1994-01-01

History of the development of nuclear materials accounting systems in USA and their purposes are considered. Many present accounting systems are based on mainframe computers with multiple terminal access. Problems of future improvement accounting systems are discussed

Management review of nuclear material control and accounting systems

International Nuclear Information System (INIS)

1975-06-01

Section 70.58, ''Fundamental Nuclear Material Controls,'' of 10 CFR Part 70, ''Special Nuclear Materials,'' requires, in paragraph 70.58(c), that certain licensees authorized to possess more than one effective kilogram of special nuclear material establish a management system to provide for the development, revision, implementation, and enforcement of nuclear material control and accounting procedures. Such a system must provide for a review of the nuclear material control system at least every 12 months. This guide describes the purpose and scope, personnel qualifications, depth of detail, and procedures that are acceptable to the NRC staff for the management review of nuclear material control systems required under paragraph 70.58(c) of 10 CFR Part 70. (U.S.)

Imaging systems and materials characterization

International Nuclear Information System (INIS)

Murr, L.E.

2009-01-01

This paper provides a broad background for the historical development and modern applications of light optical metallography, scanning and transmission electron microscopy, field-ion microscopy and several forms of scanning probe microscopes. Numerous case examples illustrating especially synergistic applications of these imaging systems are provided to demonstrate materials characterization especially in the context of structure-property-performance issues which define materials science and engineering

System to detect nuclear materials by active neutron method

International Nuclear Information System (INIS)

Koroev, M.; Korolev, Yu.; Lopatin, Yu.; Filonov, V.

1999-01-01

The report presents the results of the development of the system to detect nuclear materials by active neutron method measuring delayed neutrons. As the neutron source the neutron generator was used. The neutron generator was controlled by the system. The detectors were developed on the base of the helium-3 counters. Each detector consist of 6 counters. Using a number of such detectors it is possible to verify materials stored in different geometry. There is an spectrometric scintillator detector in the system which gives an additional functional ability to the system. The system could be used to estimate the nuclear materials in waste, to detect the unauthorized transfer of the nuclear materials, to estimate the material in tubes [ru

Integrated alternative energy systems for use in small communities

Science.gov (United States)

Thornton, J.

1982-01-01

This paper summarizes the principles and conceptual design of an integrated alternative energy system for use in typical farming communities in developing countries. A system is described that, utilizing the Sun and methane produced from crop waste, would supply sufficient electric and thermal energy to meet the basic needs of villagers for water pumping, lighting, and cooking. The system is sized to supply enough pumping capacity to irrigate 101 ha (249 acres) sufficiently to optimize annual crop yields for the community. Three economic scenarios were developed, showing net benefits to the community of $3,578 to $15,547 anually, payback periods of 9.5 to 20 years, and benefit-to-cost ratios of 1.1 to 1.9.

Operational advanced materials control and accountability system

International Nuclear Information System (INIS)

Malanify, J.J.; Bearse, R.C.; Christensen, E.L.

1980-01-01

An accountancy system based on the Dynamic Materials Accountability (DYMAC) System has been in operation at the Plutonium Processing Facility at the Los Alamos Scientific Laboratory (LASL) since January 1978. This system, now designated the Plutonium Facility/Los Alamos Safeguards System (PF/LASS), has enhanced nuclear material accountability and process control at the LASL facility. The nondestructive assay instruments and the central computer system are operating accurately and reliably. As anticipated, several uses of the system have developed in addition to safeguards, notably scrap control and quality control. The successes of this experiment strongly suggest that implementation of DYMAC-based systems should be attempted at other facilities. 20 refs

FMDP reactor alternative summary report. Volume 1 - existing LWR alternative

International Nuclear Information System (INIS)

Greene, S.R.; Bevard, B.B.

1996-01-01

Significant quantities of weapons-usable fissile materials [primarily plutonium and highly enriched uranium (HEU)] are becoming surplus to national defense needs in both the United States and Russia. These stocks of fissile materials pose significant dangers to national and international security. The dangers exist not only in the potential proliferation of nuclear weapons but also in the potential for environmental, safety, and health (ES ampersand H) consequences if surplus fissile materials are not properly managed. This document summarizes the results of analysis concerned with existing light water reactor plutonium disposition alternatives

FMDP reactor alternative summary report. Volume 1 - existing LWR alternative

Energy Technology Data Exchange (ETDEWEB)

Greene, S.R.; Bevard, B.B. [and others

1996-10-07

Significant quantities of weapons-usable fissile materials [primarily plutonium and highly enriched uranium (HEU)] are becoming surplus to national defense needs in both the United States and Russia. These stocks of fissile materials pose significant dangers to national and international security. The dangers exist not only in the potential proliferation of nuclear weapons but also in the potential for environmental, safety, and health (ES&H) consequences if surplus fissile materials are not properly managed. This document summarizes the results of analysis concerned with existing light water reactor plutonium disposition alternatives.

Alternative drives for motor cars. Hybrid systems, fuel cells, alternative energy sources. 2. enl. ed.; Alternative Antriebe fuer Automobile. Hybridsysteme, Brennstoffzellen, alternative Energietraeger

Energy Technology Data Exchange (ETDEWEB)

Stan, Cornel [Berkeley Univ., CA (United States)]|[Paris Univ. (France)]|[Pisa Univ. (Italy)]|[Perugia Univ. (Italy)]|[Westsaechsischen Hochschule Zwickau (Germany)

2008-07-01

The implementation possibilities of future drive concepts - from hybrid systems comprising an electric motor and an internal combustion engine to fuel cells to alternative fuels like hydrogen or alcohol - will depend largely on quality criteria, e.g. power density, rotary momentum, acceleration characteristics, specific energy consumption, emissions of chemical substances, and noise. The boundary criteria for the introduction of realizeable concepts of alternative drives for motor cars will be defined by the availability and storability of the envisaged fuels, technical complexity, cost, safety, infrastructure and service. The book presents and analyzes the processes, drives and energy sources that can be combined in complex energy management systems for motor cars in accordance with the aforementioned criteria. Knowledge about these facts is indispensable for the development of new concepts. The 2nd edition describes many new developments in car propulsion systems as well as their combinations, new energy sources, energy converters and energy stores. All contents and literature reflect the latest state of science and technology. (orig.) [German] Ueber die Realisierungsmoeglichkeiten zukuenftiger Antriebskonzepte - von Hybridsystemen Elektro-/Verbrennungsmotor ueber Brennstoffzellen bis zu alternativen Energietraegern wie Wasserstoff oder Alkohol - werden fundierte Kriterien der Qualitaet eines Antriebs entscheiden. Leistungsdichte, Drehmomentverlauf, Beschleunigungscharakteristik, spezifischer Energieverbrauch sowie Emission chemischer Stoffe und Geraeusche sind dafuer wichtige Merkmale zur Qualitaetsbeurteilung. Die Verfuegbarkeit und die Speicherfaehigkeit vorgesehener Energietraeger, die technische Komplexitaet, Kosten, Sicherheit, Infrastruktur und Service werden die Randbedingungen fuer die Einfuehrung realisierbarer Konzepte alternativer Antriebe fuer Automobile stellen. Die Uebersicht und die Analyse der Prozesse, Antriebsmaschinen und Energietraeger, die

7 CFR 1726.253 - Prior approved contract modification related to alternative bid provision for payment to...

Science.gov (United States)

2010-01-01

... alternative bid provision for payment to contractor for bulk purchase of materials. 1726.253 Section 1726.253... contractor for bulk purchase of materials. When construction is to be performed over an extended period of... AGRICULTURE ELECTRIC SYSTEM CONSTRUCTION POLICIES AND PROCEDURES Modifications to RUS Standard Contract Forms...

Advances in concrete materials for sewer systems affected by microbial induced concrete corrosion: A review.

Science.gov (United States)

Grengg, Cyrill; Mittermayr, Florian; Ukrainczyk, Neven; Koraimann, Günther; Kienesberger, Sabine; Dietzel, Martin

2018-05-01

Microbial induced concrete corrosion (MICC) is recognized as one of the main degradation mechanisms of subsurface infrastructure worldwide, raising the demand for sustainable construction materials in corrosive environments. This review aims to summarize the key research progress acquired during the last decade regarding the understanding of MICC reaction mechanisms and the development of durable materials from an interdisciplinary perspective. Special focus was laid on aspects governing concrete - micoorganisms interaction since being the central process steering biogenic acid corrosion. The insufficient knowledge regarding the latter is proposed as a central reason for insufficient progress in tailored material development for aggressive wastewater systems. To date no cement-based material exists, suitable to withstand the aggressive conditions related to MICC over its entire service life. Research is in particular needed on the impact of physiochemical material parameters on microbial community structure, growth characteristics and limitations within individual concrete speciation. Herein an interdisciplinary approach is presented by combining results from material sciences, microbiology, mineralogy and hydrochemistry to stimulate the development of novel and sustainable materials and mitigation strategies for MICC. For instance, the application of antibacteriostatic agents is introduced as an effective instrument to limit microbial growth on concrete surfaces in aggressive sewer environments. Additionally, geopolymer concretes are introduced as highly resistent in acid environments, thus representing a possible green alternative to conventional cement-based construction materials. Copyright © 2018 Elsevier Ltd. All rights reserved.

Workshop on materials control and accounting system design

International Nuclear Information System (INIS)

Pillay, K.K.S.

1989-01-01

The chapter describes the workshop aimed at reinforcing, through participation in the design exercise, the concepts of nuclear materials control and accountability. Topics include: workshop format; key elements of a materials management and accounting (MC and A) system; and MC and A system design including safeguards organization and management, material access areas, key measurement points, nuclear materials measurements, physical inventory, material balance closings, and internal controls. Appended to this chapter is a detailed description of a facility that produces metallic plutonium and the safeguards requirements for this facility

Tubo de PVC liso com diferentes envoltórios como material alternativo na drenagem subterrânea Smooth PVC tube with different envelopes as an alternative material in the subsurface drainage

Directory of Open Access Journals (Sweden)

Florício P. de Almeida

2003-04-01

Full Text Available Em regiões áridas e semi-áridas irrigadas a drenagem é, freqüentemente, necessária para prevenir o encharcamento do solo e o controle da salinidade. Um dos principais obstáculos na instalação de um sistema de drenagem subterrânea é o alto custo do investimento inicial. Assim, alguma contribuição que reduza o custo da instalação dos drenos e também do material usado, é altamente vantajosa. Diante disso, o objetivo desta pesquisa foi avaliar, em condições de laboratório, o desempenho hidráulico do sistema drenante constituído pelo tubo de PVC liso, próprio para esgoto doméstico, de 50,0 mm de diâmetro nominal e área aberta de 23,0 cm² m-1, e por três tipos de envoltório. O desempenho do tubo drenante de PVC liso demonstrou que esse material é tecnicamente viável para drenagem agrícola, principalmente com o uso de brita como envoltório.In irrigated arid and semi-arid regions the drainage is, frequently, necessary to prevent the waterlogging of the soil and to control the salinity. One of the main obstacles in the installation of a subsurface drainage system is the high cost of the initial investment. Thus, some contribution that reduces the cost of the installation of the drains and also of the material used is highly advantageous. The objective of this research was to evaluate, under laboratory conditions, the hydraulic performance of the drainage system constituted by smooth PVC tube used for sewer with 50.0 mm of nominal diameter and open area of 23.0 cm² m-1 and different types of envelopes, as an alternative material for subsurface drainage. The performance of the smooth PVC tube demonstrated that this material is technically viable for agricultural drainage principally when used with single stones as envelope.

Alternative approach to estimate the hydrolysis rate constant of particulate material from batch data

International Nuclear Information System (INIS)

Koch, Konrad; Drewes, Jörg E.

2014-01-01

Highlights: • An alternative to the commonly used first-order approach is presented. • A relationship between k h and the 1% criterion of the VDI 4630 is deduced. • Equation is proposed to directly calculate k h without the need for data fitting. • Hydrolysis constant k h can then easily be read-off from a table. - Abstract: As anaerobic batch tests are easy to conduct, they are commonly used to assess the effects of different operational factors on the anaerobic digestion process. Hydrolysis of particulate material is often assumed to be the rate limiting step in anaerobic digestion. Its velocity is often estimated by data fitting from batch tests. In this study, a Monod-type alternative to the commonly used first-order approach is presented. The approach was adapted from balancing a continuously stirred-tank reactor and better accommodates the fact that even after a long incubation time, some of the methane potential of the substrate remains untapped in the digestate. In addition, an equation is proposed to directly calculate the hydrolysis constant from the time when the daily gas production is less than 1% of the total gas production. The hydrolysis constant can then easily be read-off from a table when the batch test duration is known

Overview of U.S. LMFBR structural materials mechanical properties program

International Nuclear Information System (INIS)

Horak, J.A.; Purdy, C.M.

This paper presents the objective, scope, and status of the U.S. Department of Energy's Materials and Structures Program to develop a data base on mechanical properties of structural materials for out-of-core structures and components for LMFBRs. Information on the development of a reference data base on materials for the reactor system, reactor enclosure system, primary heat transport system, intermediate heat transport system, and steam generator system is included. In addition, the development of the data and analyses to account for the effects of temperature and stress, as well as water/steam, sodium, and radiation environments, is described. Plans for the development of alternative materials for future out-of-core applications are presented. (author)

Radiation doses in alternative commercial high-level waste management systems

International Nuclear Information System (INIS)

Schneider, K.J.; Pelto, P.J.; Lavender, J.C.; Daling, P.M.; Fecht, B.A.

1986-01-01

In the commercial high-level waste management system, potential changes are being considered that will augment the benefits of an integral monitored retrievable storage (MRS) facility. The US Department of Energy (DOE) has recognized that alternative options could be implemented in the authorized waste management system (i.e., without an integral MRS facility) to potentially achieve some of the same beneficial effects of the integral MRS system. This paper summarizes those DOE-sponsored analyses related to radiation doses resulting from changes in the waste management system. This report presents generic analyses of aggregated radiation dose impacts to the public and occupational workers, of nine postulated changes in the operation of a spent-fuel management system without an MRS facility

Nuclear material accountability system in DUPIC facility (I)

International Nuclear Information System (INIS)

Ko, W. I.; Kim, H. D.; Byeon, K. H.; Song, D. Y.; Lee, B. D.; Hong, J. S.; Yang, M. S.

1999-01-01

KAERI(Korea Atomic Energy Research Institute) has developed a nuclear material accountability system for DUPIC(Direct Use of Spent PWR Fuel in CANDU) fuel cycle process. The software development for the material accountability started with a general model software, so-called CoreMAS(Core Material Accountability System), at the beginning of 1998. The development efforts have been focused on the DUPIC safeguards system, and in addition, improved to meet Korean safeguards requirements under domestic laws and regulations. The software being developed as a local area network-based accountability system with multi-user environment is able to track and control nuclear material flow within a facility and inter-facility. In addition, it could be operated in a near-real time manner and also able to generate records and reports as necessary for facility operator and domestic and international inspector. This paper addresses DMAS(DUPIC Material Accountability System) being developed by KAERI and simulation in a small-scale DUPIC process for the verification of the software performance and for seeking further works

Revisiting Bourdieu: Alternative Educational Systems in the Light of the Theory of Social and Cultural Reproduction

Science.gov (United States)

Azaola, Marta Cristina

2012-01-01

The paper reflects upon the principles and practice of an alternative educational system operating in rural Mexico in the light of Bourdieu's theory of cultural and social reproduction. Bourdieu's theory seeks to explain processes of reproduction of power relations within schools and society; whereas alternative educational systems seek to expand…

Irradiation as an alternative environmentally friendly method for microbiological decontamination of herbal raw material

International Nuclear Information System (INIS)

Dragusin, M.; Rotaru, R.

2000-01-01

Microbiological contamination of herbal raw materials is a serious problem in the production of therapeutical preparations. A good quality of the product, according to the pharmaceutical requirements may be achieved by applying suitable methods of decontamination. The decontamination treatments should be fast and effective against all microorganisms. It should ensure the decontamination of both packaging and the microorganisms present and must not reduce the sensory and technological qualities of the commodities. Decontamination of herbal raw materials by irradiation is a method by choice. It is because chemical methods are recognized recently as not safe to the consumer. Irradiation, in turn, is technically feasible, very effective and friendly enough to environment process. Under the prevailing production and handling conditions, most herbs contain a large number of microorganisms what is a serious problem in the production of therapeutical preparations. For several years the most widely used methods for decontamination of herbs was fumigation with ethylene oxide or methyl bromide. Both methods today banned in most countries. Irradiation is an alternative and safe method for effective reducing the microbial contamination of herbal raw materials. The following raw materials have been examined: Folium Cynara, Folium Plantago, Flos Chamomillae, Semen Sylibum Marianum and Folium Farfara. The content of biologically active compounds before and after irradiation of the raw materials did not change in a significant degree after irradiation. The dose of radiation for herbals raw materials was 10 kGy. There are two groups of raw materials: - The raw materials designed for preparing granulates, tablets, dragees, capsules, aqueous extracts, infusions, macerations and preparations for external use; - The raw materials assigned for preparing alcoholic preparations, isolated compounds, oil preparations and essential oils. The medical herbs and herbal raw materials before their

Cost Benefit and Alternatives Analysis of Distribution Systems with Energy Storage Systems: Preprint

Energy Technology Data Exchange (ETDEWEB)

Harris, Tom; Nagarajan, Adarsh; Baggu, Murali; Bialek, Tom

2017-06-27

This paper explores monetized and non-monetized benefits from storage interconnected to distribution system through use cases illustrating potential applications for energy storage in California's electric utility system. This work supports SDG&E in its efforts to quantify, summarize, and compare the cost and benefit streams related to implementation and operation of energy storage on its distribution feeders. This effort develops the cost benefit and alternatives analysis platform, integrated with QSTS feeder simulation capability, and analyzed use cases to explore the cost-benefit of implementation and operation of energy storage for feeder support and market participation.

Test plan for buried waste containment system materials

International Nuclear Information System (INIS)

Weidner, J.; Shaw, P.

1997-03-01

The objectives of the FY 1997 barrier material work at the Idaho National Engineering and Environmental Laboratory are to (1) select a waste barrier material and verify that it is compatible with the Buried Waste Containment System Process, and (2) determine if, and how, the Buried Waste Containment System emplacement process affects the material properties and performance (on proof of principle scale). This test plan describes a set of measurements and procedures used to validate a waste barrier material for the Buried Waste Containment System. A latex modified proprietary cement manufactured by CTS Cement Manufacturing Company will be tested. Emplacement properties required for the Buried Waste Containment System process are: slump between 8 and 10 in., set time between 15 and 30 minutes, compressive strength at set of 20 psi minimum, and set temperature less than 100 degrees C. Durability properties include resistance to degradation from carbonate, sulfate, and waste-site soil leachates. A set of baseline barrier material properties will be determined to provide a data base for comparison with the barrier materials when tested in the field. The measurements include permeability, petrographic analysis to determine separation and/or segregation of mix components, and a set of mechanical properties. The measurements will be repeated on specimens from the field test material. The data will be used to determine if the Buried Waste Containment System equipment changes the material. The emplacement properties will be determined using standard laboratory procedures and instruments. Durability of the barrier material will be evaluated by determining the effect of carbonate, sulfate, and waste-site soil leachates on the compressive strength of the barrier material. The baseline properties will be determined using standard ASTM procedures. 9 refs., 1 fig., 2 tabs

Alternate Methods of Effluent Disposal for On-Lot Home Sewage Systems. Special Circular 214.

Science.gov (United States)

Wooding, N. Henry

This circular provides current information for homeowners who must repair or replace existing on-lot sewage disposal systems. Several alternatives such as elevated sand mounds, sand-lined beds and trenches and oversized absorption areas are discussed. Site characteristics and preparation are outlined. Each alternative is accompanied by a diagram…

Essential oils: an alternative approach to management of powdery mildew diseases

Directory of Open Access Journals (Sweden)

Elena STURCHIO

2015-01-01

Full Text Available In recent years there has been growing interest in the application of plant-derived substances in agriculture as alternatives to the use of pesticides, in order to obtain healthy crops and more environmentally sustainable crop production systems. The properties of some essential oils as natural fungicides were evaluated, to promote their use in alternative agriculture. Potentially detrimental effects caused by essential oil residues in soil were also assessed by mutagenicity assays to avoid possible adverse effects related to the use of these materials. Trials in a controlled environment were set up, using ‘Romanesco’ zucchini treated with essential oils, either exclusively or alternated with a synthetic fungicide. The treatments were applied when natural infection by Podosphaera xanthii appeared on test plants, and powdery mildew incidence and severity were assessed after six weeks. Preliminary results indicated that the alternation of natural materials with effective synthetic fungicide maintained effective disease control, and may also assist with management of pesticide resistance in P. xanthii. No relevant mutagenic effects of essential oil residues in soil were revealed, although an appropriate formulation useful under field conditions is required for effective application.

Biomechanical findings in rats undergoing fascial reconstruction with graft materials suggested as an alternative to polypropylene.

Science.gov (United States)

Konstantinovic, M L; Ozog, Y; Spelzini, F; Pottier, C; De Ridder, D; Deprest, J

2010-03-01

Graft materials used for pelvic floor reinforcement should still be considered as investigational and, therefore, evaluated experimentally and within clinical trials. The present report describes our biomechanical findings in rats implanted with selected novel implant materials, which in recent years have been suggested as alternatives to plain polypropylene (PP) meshes. Full thickness abdominal wall defects were primarily repaired by the implant of interest. Experiments involved eight different implant materials: two partly degradable synthetic implants, that is, a hybrid of polyglactin 910 with PP (Vypro II) and collagen coated PP (Pelvitex); two non-cross linked (Surgisis, InteXēn LP) and two cross-linked materials (Pelvicol, Pelvisoft) and two porous modifications of InteXēn LP and Pelvicol implants. At different time points (7, 14, 30, and 90 days), the implants and surrounding host tissue (explant) were harvested and tensiometry was performed. Tensile strength and location of breakage were recorded. In general resorbable non-cross linked collagen matrices and porous materials were weaker after 90 days; similar behavior was seen for implant materials alone and their construction with the surrounding native tissue. Both non-porous and porous modification of InteXēn LP appeared at 90 days as a very thin layer of collagen that was two-thirds, respectively one-third of the initial thickness. In experimental conditions, sufficient strength was obtained only after 3 months, and PP containing constructs appeared as the strongest though reconstruction with Pelvicol showed comparable outcomes. Lower values for strength of non-cross linked and porous collagen materials are questioning their efficacy for pelvic floor reconstruction. (c) 2009 Wiley-Liss, Inc.

Status Report on Structural Materials for Advanced Nuclear Systems

International Nuclear Information System (INIS)

Allen, T.R.; Balbaud-Celerier, F.; Asayama, T.; Pouchon, M.; Busby, J.T.; Maloy, S.; Park, J.Y.; Fazio, C.; Dai, Y.; Agostini, P.; Chevalier, J.P.; Marrow, J.

2013-01-01

Materials performance is critical to the safe and economic operation of any nuclear system. As the international community pursues the development of Generation IV reactor concepts and accelerator-driven transmutation systems, it will be increasingly necessary to develop advanced materials capable of tolerating the more challenging environments of these new systems. The international community supports numerous materials research programmes, with each country determining its individual focus on a case-by-case basis. In many instances, similar alloys of materials systems are being studied in several countries, providing the opportunity for collaborative and cross-cutting research that benefits different systems. This report is a snapshot of the current materials programmes supporting the development of advanced concepts. The descriptions of the research are grouped by concept, and national programmes are described within each concept. The report provides an overall sense of the importance of materials research worldwide and the opportunities for synergy among the countries represented in this overview. (authors)

Design of online testing system of material radiation resistance

International Nuclear Information System (INIS)

Wan Junsheng; He Shengping; Gao Xinjun

2014-01-01

The capability of radiation resistance is important for some material used in some specifically engineering fields. It is the same principal applied in all existing test system that compares the performance parameter after radiation to evaluate material radiation resistance. A kind of new technique on test system of material radiation resistance is put forward in this paper. Experimentation shows that the online test system for material radiation resistance works well and has an extending application outlook. (authors)

High belite cement from alternative raw materials

Directory of Open Access Journals (Sweden)

Ghorab, H. Y.

2014-05-01

Full Text Available Three high belite laboratory clinkers were prepared from traditional and alternative raw materials. Reference clinker was obtained from 77% limestone, 11% sandy clays, 11% fatty clays and 1% iron scales. The fatty clays were replaced by red brick powder in the raw meal of the second clinker and were lowered to 2% with the replacement of 10% of the limestone by egg shells in the third clinker. The SEM examination revealed clear presence of crossed striae and twinning in the rounded belite grains of the reference clinker caused by the transformation of the α´-belite to the β polymorph. Striae were weaker in the second and third clinkers indicating a probable stabilization of the α ‘-belite polymorph. Compressive strength of the respective cements were attained first after 28 days and the early strength did not improve with increasing fineness. Higher compressive strength values were found for the cement prepared from second clinker.Se han preparado tres clinkeres de laboratorio con altos contenidos en belita a partir de materias primas tradicionales y alternativas. El clinker de referencia se obtuvo a partir de una mezcla de caliza, arcillas arenosas y grasas y limaduras de hierro. Las arcillas grasas fueron sustituidas por polvo de ladrillo rojo en la preparación del segundo clinker, y en el tercero el contenido de arcilla grasa fue de solo un 2% y parte de la caliza fue sustituida por cascara de huevo. El estudio realizado por SEM muestra superficies estriadas alrededor de los granos de belita que indican una transformación del polimorfo α´ a la forma β-C₂S, durante el enfriamiento. Esas estrías son menos marcadas en el segundo y tercer clinker, indicando, una estabilización del polimorfo α´-C₂S. Los valores de resistencias a compresión de los correspondientes cementos, a 28 días de curado, no se ven incrementados por la finura de dichos cementos. Las mayores resistencias se obtuvieron en el cemento preparado a partir del cl

Nuclear Space Power Systems Materials Requirements

International Nuclear Information System (INIS)

Buckman, R.W. Jr.

2004-01-01

High specific energy is required for space nuclear power systems. This generally means high operating temperatures and the only alloy class of materials available for construction of such systems are the refractory metals niobium, tantalum, molybdenum and tungsten. The refractory metals in the past have been the construction materials selected for nuclear space power systems. The objective of this paper will be to review the past history and requirements for space nuclear power systems from the early 1960's through the SP-100 program. Also presented will be the past and present status of refractory metal alloy technology and what will be needed to support the next advanced nuclear space power system. The next generation of advanced nuclear space power systems can benefit from the review of this past experience. Because of a decline in the refractory metal industry in the United States, ready availability of specific refractory metal alloys is limited

Corrosion behaviour of materials selected for FMIT lithium system

Energy Technology Data Exchange (ETDEWEB)

Bazinet, G.D.; Brehm, W.F.

1983-09-01

The corrosion behavior of selected materials in a liquid lithium environment was studied in support of system and component designs for the Fusion Materials Irradiation Test (FMIT) Facility. Testing conditions ranged from about 3700 to about6500 hours of exposure to flowing lithium at temperatures from 230/sup 0/ to 270/sup 0/C and static lithium at temperatures from 200/sup 0/ to 500/sup 0/C. Principal areas of investigation included lithium corrosion/erosion effects on FMIT lithium system baseline and candidate materials. Material coupons and full-size prototypic components were evaluated to determine corrosion rates, fatigue crack growth rates, structural compatibility, and component acceptability for the lithium system. Based on the results of these studies, concerns regarding system materials and component designs were satisfactorily resolved to support a 20-year design life requirement for the FMIT lithium system.

Corrosion behaviour of materials selected for FMIT lithium system

International Nuclear Information System (INIS)

Bazinet, G.D.; Brehm, W.F.

1983-01-01

The corrosion behavior of selected materials in a liquid lithium environment was studied in support of system and component designs for the Fusion Materials Irradiation Test (FMIT) Facility. Testing conditions ranged from about 3700 to about6500 hours of exposure to flowing lithium at temperatures from 230 0 to 270 0 C and static lithium at temperatures from 200 0 to 500 0 C. Principal areas of investigation included lithium corrosion/erosion effects on FMIT lithium system baseline and candidate materials. Material coupons and full-size prototypic components were evaluated to determine corrosion rates, fatigue crack growth rates, structural compatibility, and component acceptability for the lithium system. Based on the results of these studies, concerns regarding system materials and component designs were satisfactorily resolved to support a 20-year design life requirement for the FMIT lithium system

Climate control systems using pozzolan materials

KAUST Repository

Almadhoun, Mahmoud Nassar Mahmoud

2016-01-01

A system and method for conditioning air is provided that optimizes the use of sustainable and locally sourced materials with agrarian, residential, and industrial applications. The system can be formed with a porous siliceous, or siliceous

Performance analysis of nuclear materials accounting systems

International Nuclear Information System (INIS)

Cobb, D.D.; Shipley, J.P.

1979-01-01

Techniques for analyzing the level of performance of nuclear materials accounting systems in terms of the four performance measures, total amount of loss, loss-detection time, loss-detection probability, and false-alarm probability, are presented. These techniques are especially useful for analyzing the expected performance of near-real-time (dynamic) accounting systems. A conservative estimate of system performance is provided by the CUSUM (cumulative summation of materials balances) test. Graphical displays, called performance surfaces, are developed as convenient tools for representing systems performance, and examples from a recent safeguards study of a nuclear fuels reprocessing plant are given. 6 refs

Advanced materials for space nuclear power systems

International Nuclear Information System (INIS)

Titran, R.H.; Grobstein, T.L.

1991-01-01

Research on monolithic refractory metal alloys and on metal matrix composites is being conducted at the NASA Lewis Research Center, Cleveland, Ohio, in support of advanced space power systems. The overall philosophy of the research is to develop and characterize new high-temperature power conversion and radiator materials and to provide spacecraft designers with material selection options and design information. Research on three candidate materials (carbide strengthened niobium alloy PWC-11 for fuel cladding, graphite fiber reinforced copper matrix composites (Gr/Cu) for heat rejection fins, and tungsten fiber reinforced niobium matrix composites (W/NB) for fuel containment and structural supports) considered for space power system applications is discussed. Each of these types of materials offers unique advantages for space power applications

ARTIFICIAL NEURAL NETWORKS BASED GEARS MATERIAL SELECTION HYBRID INTELLIGENT SYSTEM

Institute of Scientific and Technical Information of China (English)

X.C. Li; W.X. Zhu; G. Chen; D.S. Mei; J. Zhang; K.M. Chen

2003-01-01

An artificial neural networks(ANNs) based gear material selection hybrid intelligent system is established by analyzing the individual advantages and weakness of expert system (ES) and ANNs and the applications in material select of them. The system mainly consists of tow parts: ES and ANNs. By being trained with much data samples,the back propagation (BP) ANN gets the knowledge of gear materials selection, and is able to inference according to user input. The system realizes the complementing of ANNs and ES. Using this system, engineers without materials selection experience can conveniently deal with gear materials selection.

Dynamic material accountancy in an integrated safeguards system

International Nuclear Information System (INIS)

Murrell, J.S.

1979-01-01

The nuclear material safeguards system at the Portsmouth Gaseous Diffusion Plant is currently being improved. A new material control system will provide computerized monitoring and accountability, and a new physical protection system will provide upgraded perimeter and portal entry monitoring. The control system incorporates remote computer terminals at all processing, transfer and storage areas throughout the plant. Terminal equipment is interfaced to a computer through teletype equipment. A typical terminal transaction would require verification that the particular activity (material movement or process operation) is authorized, identifying the container involved, weighing the container, and then verifying the enrichment with non-destructive assay instrumentation. The system, when fully operational, will provide near real-time accountability for each eight-hour work shift for all items in process. (author)

Dynamic material accountancy in an integrated safeguards system

International Nuclear Information System (INIS)

Murrell, J.S.

1978-01-01

The nuclear material safeguards system at the Portsmouth Gaseous Diffusion Plant is currently being improved. A new material control system will provide computerized monitoring and accountability, and a new physical protection system will provide upgraded perimeter and portal entry monitoring. The control system incorporates remote computer terminals at all processing, transfer, and storage areas throughout the plant. Terminal equipment is interfaced to a computer through teletype equipment. A typical terminal transaction would require verification that the particular activity (material movement or process operation) is authorized, identifying the container involved, weighing the container, and then verifying the enrichment with non-destructive assay instrumentation. The system, when fully operational, will provide near real-time accountability for each eight-hour work shift for all items in process

A future vision of nuclear material information systems

International Nuclear Information System (INIS)

Suski, N.; Wimple, C.

1999-01-01

To address the current and future needs for nuclear materials management and safeguards information, Lawrence Livermore National Laboratory envisions an integrated nuclear information system that will support several functions. The vision is to link distributed information systems via a common communications infrastructure designed to address the information interdependencies between two major elements: Domestic, with information about specific nuclear materials and their properties, and International, with information pertaining to foreign nuclear materials, facility design and operations. The communication infrastructure will enable data consistency, validation and reconciliation, as well as provide a common access point and user interface for a broad range of nuclear materials information. Information may be transmitted to, from, and within the system by a variety of linkage mechanisms, including the Internet. Strict access control will be employed as well as data encryption and user authentication to provide the necessary information assurance. The system can provide a mechanism not only for data storage and retrieval, but will eventually provide the analytical tools necessary to support the U.S. government's nuclear materials management needs and non-proliferation policy goals

Energy storage and alternatives to improve train voltage on a mass transit system

Science.gov (United States)

Gordon, S. P.; Rorke, W. S.

1995-04-01

The wide separation of substations in the Bay Area Rapid Transit system's transbay tunnel contributes to voltage sag when power demand is high. In the future, expansions to the system will exacerbate this problem by increasing traffic density. Typically, this situation is remedied through the installation of additional substations to increase the system's power capacity. We have evaluated the efficacy of several alternatives to this approach - specifically, installation of an 8 megajoule energy storage system, modification of the existing substations, or reduction of the resistance of the running rails or the third rail. To support this analysis, we have developed a simple model of the traction power system in the tunnel. We have concluded that the storage system does not have sufficient capacity to deal with the expected voltage sags; in this application, the alternatives present more effective solutions. We have also investigated the potential impact of these system upgrades on expected future capital outlays by BART for traction power infrastructure additions. We have found that rail or substation upgrades may reduce the need for additional substations. These upgrades may also be effective on other parts of the BART system and on other traction power systems.

Incorporation of an item/material attribute system into PAMTRAK

International Nuclear Information System (INIS)

Anspach, D.A.; Waddoups, I.G.; Fox, E.T.

1994-01-01

The Department of Energy (DOE) mission is changing due to the number of nuclear weapon reductions by the United States and the former Soviet Union with long-term storage requirements for DOE sites increasing. New technology to ensure the integrity of special nuclear material (SNM) in storage is available to sites to supplement manual physical inventories. This allows them to decrease operating costs while keeping radiation exposure at minimal levels. We have developed a generic, real time, personnel tracking and material monitoring system named PAMTRAK. Such a system can significantly reduce the number of required, manual physical inventories at DOE sites while increasing assurance that an insider has not diverted or stolen material. Until recently Pamtrak used only material monitoring devices that provided location/containment attributes. However, Westinghouse Electric Corp. and Metrox, Inc. have recently developed hard-wired item/material attribute systems that monitor both temperature and weight. We have incorporated both of these systems into PAMTRAK. If a site employed one of these item/material attribute systems, it could decrease its manual inventory frequency to three years. This paper describes how a site might implement such a system to meet the DOE's requirements

Hungarian national nuclear material control and accounting system

International Nuclear Information System (INIS)

Lendvai, O.

1985-01-01

The Hungarian system for nuclear materials control and accounting is briefly described. Sections include a historical overview, a description of nuclear activities and an outline of the organizational structure of the materials management system. Subsequent sections discuss accounting, verification and international relations

The environment and the use of alternative fuels

International Nuclear Information System (INIS)

Okken, P.A.

1992-05-01

The contribution of the Netherlands Energy Research Foundation (ECN) to the ANWB symposium on alternative fuels and techniques concerns the necessity to use alternatives to reduce CO 2 emissions, the importance of system integration, and a discussion of the strong and weak points with regard to the introduction of the fuel alternatives in the Netherlands. First attention is paid to the greenhouse effect (CO 2 emissions) of the use of fuels. Options to reduce CO 2 emission from automobiles are mentioned. Than several alternative fuels and accompanying techniques, and their impact on the CO 2 emission, are discussed: diesel, liquid petroleum gas (LPG), compressed natural gas (CNG), methanol, ethanol, rapeseed, electricity, and hydrogen. The possibilities to reduce CO 2 emission in the Netherlands can be calculated by means of the Energy and Materials Scenarios (EMS). For several aspects assessments are given for the above-mentioned alternatives: availability of technology, ease of fuel storage, risk of use, impact on the city climate, full fuel cycle CO 2 emission, costs, and reserves. These aspects can be considered as valid for most of the industrialized countries. For the Netherlands two other aspects have been assessed: the interest of the oil industry in the introduction of alternative fuels, the availability of the alternatives in the Netherlands. 5 figs., 6 tabs., 10 refs

Accounting systems for special nuclear material control. Technical report

International Nuclear Information System (INIS)

Korstad, P.A.

1980-05-01

Nuclear material accounting systems were examined and compared to financial double-entry accounting systems. Effective nuclear material accounting systems have been designed using the principles of double-entry financial accounting. The modified double-entry systems presently employed are acceptable if they provide adequate control over the recording and summarizing of transactions. Strong internal controls, based on principles of financial accounting, can help protect nuclear materials and produce accurate, reliable accounting data. An electronic data processing system can more accurately maintain large volumes of data and provide management with more current, reliable information

Security features of a nuclear material accounting system

International Nuclear Information System (INIS)

Erkkila, B.H.

1988-01-01

The Los Alamos Nuclear Material Accounting and Safeguards System (MASS) is a near-real-time accountability system for bulk materials, discrete items, and materials undergoing dynamic processing. MASS has evolved from a 80-column, card-based process control system to a very sophisticated computer system. Recently, the computer hardware was upgraded to a modern transaction oriented central computer system designed to accommodate extensive growth in the foreseeable future. The security of the MASS computer system is provided through various access controls. There are two kinds of access controls to be addressed. They are physical access control to the hardware which make up the system and access control to the software. There are many features which provide a measure of security to the hardware that are discussed. Access to the software is controlled by a security password. Access to various transaction activities in the system is controlled through the level of MASS under privilege. Details of MASS user privilege are discussed

Evaluation of Flammable Gas Monitoring and Ventilation System Alternatives for Double-Contained Receiver Tanks

International Nuclear Information System (INIS)

GUSTAVSON, R.D.

1999-01-01

This study identifies possible flammable gas monitoring and ventilation system alternatives to ensure adequate removal of flammable gases from the Double-Contained Receiver Tank (DCRT) primary tanks during temporary storage of small amounts of waste. The study evaluates and compares these alternatives to support closure of the Flammable Gas Unreviewed Safety Question (USQ TF-96-04330)

The material politics of waste disposal - decentralization and integrated systems

Directory of Open Access Journals (Sweden)

Penelope Harvey

2012-12-01

Full Text Available This article and the previous «Convergence and divergence between the local and regional state around solid waste management. An unresolved problem in the Sacred Valley» from Teresa Tupayachi are published as complementary accounts on the management of solid waste in the Vilcanota Valley in Cusco. Penelope Harvey and Teresa Tupayachi worked together on this theme. The present article explores how discontinuities across diverse instances of the state are experienced and understood. Drawing from an ethnographic study of the Vilcanota Valley in Cusco, the article looks at the material politics of waste disposal in neoliberal times. Faced with the problem of how to dispose of solid waste, people from Cusco experience a lack of institutional responsibility and call for a stronger state presence. The article describes the efforts by technical experts to design integrated waste management systems that maximise the potential for re-cycling, minimise toxic contamination, and turn ‘rubbish’ into the altogether more economically lively category of ‘solid waste’. However while the financialization of waste might appear to offer an indisputable public good, efforts to instigate a viable waste disposal business in a decentralizing political space elicit deep social tensions and contradictions. The social discontinuities that decentralization supports disrupt ambitions for integrated solutions as local actors resist top-down models and look not just for alternative solutions, but alternative ways of framing the problem of urban waste, and by extension their relationship to the state.

An information system for sustainable materials management with material flow accounting and waste input–output analysis

Directory of Open Access Journals (Sweden)

Pi-Cheng Chen

2017-05-01

Full Text Available Sustainable materials management focuses on the dynamics of materials in economic and environmental activities to optimize material use efficiency and reduce environmental impact. A preliminary web-based information system is thus developed to analyze the issues of resource consumption and waste generation, enabling countries to manage resources and wastes from a life cycle perspective. This pioneering system features a four-layer framework that integrates information on physical flows and economic activities with material flow accounting and waste input–output table analysis. Within this framework, several applications were developed for different waste and resource management stakeholders. The hierarchical and interactive dashboards allow convenient overview of economy-wide material accounts, waste streams, and secondary resource circulation. Furthermore, the system can trace material flows through associated production supply chain and consumption activities. Integrated with economic models; this system can predict the possible overloading on the current waste management facility capacities and provide decision support for designing strategies to approach resource sustainability. The limitations of current system are specified for directing further enhancement of functionalities.

Potential Use Of Carbide Lime Waste As An Alternative Material To Conventional Hydrated Lime Of Cement-Lime Mortars

OpenAIRE

Al Khaja, Waheeb A.

1992-01-01

The present study aimed at the possibility of using the carbide lime waste as an alternative material to the conventional lime used for cement-lime mortar. The waste is a by-product obtained in the generation of acetylene from calcium carbide. Physical and chemical properties of the wastes were studied. Two cement-lime-sand mix proportions containing carbide lime waste were compared with the same mix proportions containing conventional lime along with a control mix without lime. Specimens wer...

Innovative IT system for material management in warehouses

Science.gov (United States)

Papoutsidakis, Michael; Sigala, Maria; Simeonaki, Eleni; Tseles, Dimitrios

2017-09-01

Nowadays through the rapid development of technology in all areas there is a constant effort to introduce technological solutions in everyday life with emphasis on materials management information systems (Enterprise Resource Planning). During the last few years the variety of these systems has been increased for small business or for SMEs as well as for larger companies and industries. In the field of material management and main management operations with automated processes, ERP applications have only recently begun to make their appearance. In this paper will be presented the development of a system for automated material storage process in a system built through specific roles that will manage materials using an integrated barcode scanner. In addition we will analyse and describe the operation and modules of other systems that have been created for the same usage. The aim of this project is to create a prototype application that will be innovative with a flexible nature that will give solutions, with low cost and it will be user friendly. This application will allow quick and proper materials management for storage. The expected result is that the application can be used by smart devices in android environment and computers without an external barcode scanner, making the application accessible to the buyer at low cost.

Fairtrade, Food Security and Globalization: Building Alternative Food Systems

Directory of Open Access Journals (Sweden)

Martin Calisto Friant

2016-05-01

Full Text Available This article examines the politics and practices of Fairtrade certification in order to assess whether this alternative trading system could contribute to innovative solutions for global food security. The analysis begins by assessing the main challenges and problems characterizing the contemporary global food system. It then explores the history, vision and certification standards of the Fairtrade label. In the third section, the results of the impact studies of Fairtrade certification on producer livelihoods are discussed, analyzing the various strengths and weaknesses. Finally the article analyzes whether, and how, the Fairtrade system could positively contribute to improving global food security. To conclude this paper argues that the greatest strength of Fairtrate is not the certification mechanism itself but rather the social and environmental principles it represents. Fairtrade standards could serve to inform broader international policies, which could lead to a sustainable transformation of the global food system.

Demonstration personnel and material tracking system at ANL-W

International Nuclear Information System (INIS)

Roybal, J.A.; Ortiz, S.; Henslee, S.P.

1988-01-01

A Personnel and Material Tracking System (PMTS) was demonstrated in the Fuel Manufacturing Facility (FMF) at Argonne National Laboratories-West (ANL-W) in July, 1987. The PMTS is intended to aid in the transfer of inventory materials from area to area within a facility such as FMF. It is also intended to assure that only those personnel who are authorized to do so may conduct these transfer operations. The PMTS Personnel Movement (PM) subsystem uses portals installed between areas to alert the system to the movement of personnel between areas. The portals are composed to two sensors, one on either side of a proximity badge reader, to detect the presence of personnel entering the portal area. However, a restricted area can be assigned to any badge holder which will cause the system to issue an alert if the badge holder passes into his/her restricted area. The PM subsystem is intended to be transparent when in use. The PMTS Inventory Material Access (IMA) subsystem provides two functions: material control and material access. The material control is provided by the Wireless Alarm Transmission of Container Handling (WATCH) system which is a sensor rf transmitter system that detects item movements. Material access is provided by the Mobile Accountability Verification Inventory Station (MAVIS) system which is a self-powered smart barcode reader

Alternatives Generation Analysis Long Length Contaminated Equipment Removal System Storage

International Nuclear Information System (INIS)

BOGER, R.M.

1999-01-01

Major pieces of Characterization sampling equipment are currently stored outdoors. This includes the Long Length Contaminated Equipment receiver trailer and transportation trailer. A decision is required to determine the preferred alternative for facilities to store and maintain this equipment. The Long Length Contaminated Equipment Removal System (LLCERS) consists of many tools, mechanisms, and controllers currently stored in various locations. Much of this equipment should be protected from the elements while being stored. Some of the LLCERS equipment should be protected with some kind of roof cover. This decision analysis is to determine the best alternative for weather protection for the large equipment requiring a cover. Additional details are included in Sections 2.0 and 5.0. Key assumptions used in this analysis are detailed in Section 3.2

Mechatronic systems and materials III

CERN Document Server

Gosiewski, Zdzislaw

2009-01-01

This very interesting volume is divided into 24 sections; each of which covers, in detail, one aspect of the subject-matter: I. Industrial robots; II. Microrobotics; III. Mobile robots; IV. Teleoperation, telerobotics, teleoperated semi-autonomous systems; V. Sensors and actuators in mechatronics; VI. Control of mechatronic systems; VII. Analysis of vibration and deformation; VIII. Optimization, optimal design; IX. Integrated diagnostics; X. Failure analysis; XI. Tribology in mechatronic systems; XII. Analysis of signals; XIII. Measurement techniques; XIV. Multifunctional and smart materials;

Test System for Thermoelectric Modules and Materials

Science.gov (United States)

Hejtmánek, J.; Knížek, K.; Švejda, V.; Horna, P.; Sikora, M.

2014-10-01

We present a design for a complex measuring device that enables its user to assess the parameters of power-generating thermoelectric modules (TEMs) (or bulk thermoelectric materials) under a wide range of temperatures ( T cold = 25°C to 90°C, T hot TEM, the actual heat flow through the module, and its mechanical load, which can be varied during the measurement. Key components of our testing setup are (i) a measuring chamber where the TEM/material is compressed between thermally shielded heating blocks equipped with a mechanical loading system and water-cooled copper-based cooler, (ii) an electrical load system, (iii) a type K thermocouple array connected to a data acquisition computer, and (iv) a thermostatic water-based cooling system with electronically controlled flow rate and temperature of cooling water. Our testing setup represents a useful tool able to assess, e.g., the thermoelectric parameters of newly developed TEMs and materials or to evaluate the thermoelectric parameters of commercially available modules and materials for comparison with values declared by the manufacturer.

Nuclear material control systems for nuclear power plants

International Nuclear Information System (INIS)

1975-06-01

Paragraph 70.51(c) of 10 CFR Part 70 requires each licensee who is authorized to possess at any one time special nuclear material in a quantity exceeding one effective kilogram to establish, maintain, and follow written material control and accounting procedures that are sufficient to enable the licensee to account for the special nuclear material in his possession under license. While other paragraphs and sections of Part 70 provide specific requirements for nuclear material control systems for fuel cycle plants, such detailed requirements are not included for nuclear power reactors. This guide identifies elements acceptable to the NRC staff for a nuclear material control system for nuclear power reactors. (U.S.)

The MaSe decision support system: Development of an integrated information system for the selection of environmentally preferable materials and products in the building process

Energy Technology Data Exchange (ETDEWEB)

Strand, Sigrid Melby

2003-07-01

New building regulations and increased focus on building related environmental burdens have created a need for guidance to design more sustainable buildings. The main objective in this thesis is to develop a decision support system, to guide decision-makers to a better selection of building materials and products, based on environmental prioritisation. The system is focused on building materials and products, but the structure of the system can be adapted to other types of decision problems. No tool is found that satisfy the identified needs for a material selection system. By studying existing methods, however important information and possible solutions are gathered, that partly could be used in a new tool. Key decision makers with respect to material and product selection are the client, the architects, the technical consultants, and the contractors when they decide on specific brands. The user of the MaSe system first identifies the materials acceptable in the specific project, based on the technical requirements. These pre-selected materials are then scored and ranked through the procedures in the MaSe system. The alternative ranking is then the basis for the selection of construction elements, materials or products. Seeing the building and real estate industry as a part of our society, it is clear that the use of material resources and pollution are areas that need improvement. The MaSe system includes environmental aspects under the headlines Resources, Ecology and Human health. When selecting building materials, factors like recycling and reuse needs to be considered. Renewability, energy and waste are other aspects included in the Resource area. Toxic substances are clearly important when it comes to building materials. Factors to be included under the headline Ecology are global warming, acidification, and photochemical oxidant formation. The emissions of toxics to air, water and soil will have effect on human health. Aspects that should be included in

Corrosion of structural materials for Generation IV systems

International Nuclear Information System (INIS)

Balbaud-Celerier, F.; Cabet, C.; Courouau, J.L.; Martinelli, L.; Arnoux, P.

2009-01-01

The Generation IV International Forum aims at developing future generation nuclear energy systems. Six systems have been selected for further consideration: sodium-cooled fast reactor (SFR), gas-cooled fast reactor (GFR), lead-cooled fast reactor (LFR), molten salt reactor (MSR), supercritical water-cooled reactor (SCWR) and very high temperature reactor (VHTR). CEA, in the frame of a national program, of EC projects and of the GIF, contributes to the structural materials developments and research programs. Particularly, corrosion studies are being performed in the complex environments of the GEN IV systems. As a matter of fact, structural materials encounter very severe conditions regarding corrosion concerns: high temperatures and possibly aggressive chemical environments. Therefore, the multiple environments considered require also a large diversity of materials. On the other hand, the similar levels of working temperatures as well as neutron spectrum imply also similar families of materials for the various systems. In this paper, status of the research performed in CEA on the corrosion behavior of the structural material in the different environments is presented. The materials studied are either metallic materials as austenitic (or Y, La, Ce doped) and ferrito-martensitic steels, Ni base alloys, ODS steels, or ceramics and composites. In all the environments studied, the scientific approach is identical, the objective being in all cases the understanding of the corrosion processes to establish recommendations on the chemistry control of the coolant and to predict the long term behavior of the materials by the development of corrosion models. (author)

Evaluation of alternative phase change materials for energy storage in solar dynamic applications

Science.gov (United States)

Crane, R. A.; Dustin, M. O.

1988-01-01

The performance of fluoride salt and metallic thermal energy storage materials are compared in terms of basic performance as applied to solar dynamic power generation. Specific performance considerations include uniformity of cycle inlet temperature, peak cavity temperature, TES utilization, and system weights. Also investigated were means of enhancing the thermal conductivity of the salts and its effect on the system performance.

Evaluation of a real-time personnel and material tracking system

International Nuclear Information System (INIS)

Trujillo, A.A.; Hoover, C.E.; Garcia, B.A.

1988-01-01

Past experience in addressing the insider threat has led to the development of general principles for mitigating the insider threat while minimizing adverse impacts on site operations. Among the general principles developed was the requirement of a real-time personnel and material tracking system. A real-time system for personnel and material tracking will aid in mitigating the insider threat by providing critical information regarding the movement and location of personnel and material. In addition, this system can provide an early detection mechanism for potential insider actions. A system integrating Radio Frequency (RF) transmitters for real-time personnel and material tracking has been developed. This system was installed and tested in an operational environment. This test was intended to demonstrate the system's ability to successfully control access to material and areas by personnel, as well as providing information regarding the status of materials in transit and storage

Energy system aspects of hydrogen as an alternative fuel in transport

International Nuclear Information System (INIS)

Ramesohl, Stephan; Merten, Frank

2006-01-01

Considering the enormous ecological and economic importance of the transport sector the introduction of alternative fuels-together with drastic energy efficiency gains-will be a key to sustainable mobility, nationally as well as globally. However, the future role of alternative fuels cannot be examined from the isolated perspective of the transport sector. Interactions with the energy system as a whole have to be taken into account. This holds both for the issue of availability of energy sources as well as for allocation effects, resulting from the shift of renewable energy from the stationary sector to mobile applications. With emphasis on hydrogen as a transport fuel for private passenger cars, this paper discusses the energy systems impacts of various scenarios introducing hydrogen fueled vehicles in Germany. It identifies clear restrictions to an enhanced growth of clean hydrogen production from renewable energy sources (RES). Furthermore, it points at systems interdependencies that call for a priority use of RES electricity in stationary applications. Whereas hydrogen can play an increasing role in transport after 2030 the most important challenge is to exploit short-mid-term potentials of boosting car efficiency

Advanced materials and coatings for energy conversion systems

Energy Technology Data Exchange (ETDEWEB)

St Pierre, George R. [Ohio State Univ., Materials Science and Engineering Dept., Columbus, OH (United States)

1997-12-31

Following an historical review of the development of high-temperature alloys for energy conversion systems including turbine engines, some of the current advances in single crystal materials, intermetallics, metal-matrix composites, and ceramic-matrix composites are discussed. Particular attention is directed at creep phenomena, fatigue properties and oxidation resistance. Included within the discussions is the current status of carbon/carbon composites as potential high-temperature engineering materials and the development of coating systems for thermal barrier and oxidation protection. The specific influences of combustion gas compositions, i.e., oxidation potential, sulfur, halides, etc. are discussed. A current list of eligible advanced materials and coatings systems is presented and assessed. Finally, the critical failure mechanism and life-prediction parameters for some of the new classes of advanced structural materials are elaborated with the view to achieving affordability and extended life with a high degree of reliability. Examples are drawn from a variety of energy conversion systems. (Author)

Value-Focused Thinking Model to Evaluate SHM System Alternatives From Military end User Requirements Point of View

Directory of Open Access Journals (Sweden)

Klimaszewski Sławomir

2016-12-01

Full Text Available The article describes Value-Focused Thinking (VFT model developed in order to evaluate various alternatives for implementation of Structural Health Monitoring (SHM system on a military aircraft. Four SHM system alternatives are considered based on: visual inspection (current approach, piezoelectric (PZT sensors, Fiber Bragg Grating (FBG sensors and Comparative Vacuum Monitoring (CVM sensors. A numerical example is shown to illustrate the model capability. Sensitivity analyses are performed on values such as Cost, Performance, Aircraft Availability and Technology Readiness Level in order to examine influence of these values on overall value of structural state of awareness provided by particular SHM system alternative.

Development of an expert system for radioactive material transportation

International Nuclear Information System (INIS)

Tamanoi, K.; Ishitobi, M.; Shinohara, Y.

1990-01-01

An expert system to deal with radioactive material transportation was developed. This expert system is based on 'Regulations for the Safe Transport of Radioactive Material' by IAEA issued 1985. IAEA published the regulations under such environments that safety transportation has become increasingly being focused as uses of radioactive materials are more pervasive, not only in nuclear field but also in non-nuclear purposes. Attentions are payed for operators and environment to establish safety in handling radioactive materials. In the 1985 regulations, detailed categorization of radioactive materials and, correspondingly, new classification of packages are introduced. This categorization is more complicated than old regulations, leading us to develop an expert system to evaluate easily the packages categorization. (author)

Life Cycle Multi-Criteria Analysis Of Alternative Energy Supply Systems For A Residential Building

Directory of Open Access Journals (Sweden)

Artur Rogoža

2013-12-01

Full Text Available The article analyses energy supply alternatives for a partially renovated residential building. In addition to the existing district heating (base case alternative systems, gas boilers, heat pumps (air-water and ground-water, solar collectors, solar cells, and combinations of these systems have been examined. Actual heat consumption of the building and electricity demand determined by the statistical method are used for simulating the systems. The process of simulation is performed using EnergyPro software. In order to select an optimal energy supply option, the life cycle analysis of all systems has been carried out throughout a life span of the building, and the estimated results of energy, environmental and economic evaluation have been converted into non-dimensional variables (3E using multi–criteria analysis.Article in Lithuanian

Performance and sustainability of two alternative rabbit breeding systems

Directory of Open Access Journals (Sweden)

M. Theau.Clément

2016-12-01

Full Text Available The aim of this study was to evaluate 2 alternative breeding systems that differ from the current system in terms of reproduction rhythm, age of females at first insemination and the age of kits at weaning and at slaughter. We measured the performance of 332 females and their offspring over 4 consecutive cycles, as well as the sustainability of the systems. We compared an intensive (group I: reproduction rhythm [RR]=35 d; first insemination [AI1]=20.6 wk of age; weaning age [WA]=32 d; slaughter age [WS]=63 d an extensive (group E: RR=49 d; AI1=16.6 wk; WA=30 d; WS=70 d and a semi-intensive system (group S: RR=42 d; AI1=19.6 wk; WA=35 d; WS=70 d considered as the control system. Sustainability was evaluated using a multicriteria assessment method that takes 14 economic, environmental and social criteria into account, for which 3 to 5 indicators were expressed as the relative score [–1; –0.5; 0; +0.5; +1] for alternative systems compared to the control system. The productivity measured at 28 d (3.5, 4.2 and 4.6 kg/AI, for groups I, S and E, respectively, at 63 d post-partum (30, 38 and 42 kg/female for 4 cycles, respectively, and the total body energy measured 3 d after the 1st and at the 4th insemination (45.4, 46.8 and 49.5 MJ, respectively, were significantly increased when the reproductive rhythm decreased (P<0.001. Before and after weaning, kit mortality decreased when the reproduction rhythm decreased (11.4, 7.3, and 1.9% and 18.3, 15.3 and 10.6% for groups I, S and E, respectively, P<0.05. Carcass quality (weight and dressing percentage was lower in I than in the S and E groups (P<0.001. On this basis, the yearly productivity per doe at weaning could be estimated at 79, 83, and 78 kg for groups I, S and E, respectively. Consequently, the productivity per reproductive cycle increases with the extensification of the breeding system. Nevertheless, compared with the current French system (S, simultaneous changes in several breeding

An alternative approach for real-time balancing of electrical power systems

NARCIS (Netherlands)

Virag, A.; Jokic, A.; Lampropoulos, I.; Hermans, R.M.; Bosch, van den P.P.J.

2012-01-01

In this paper, we focus on the inefficiencies of current real-time balancing of power systems and propose an alternative solution. Our approach is based on the introduction of double-sided markets for the provision of secondary control and a market-based provision of primary control. We propose

Design and analysis of a novel latch system implementing fiber-reinforced composite materials

Science.gov (United States)

Guevara Arreola, Francisco Javier

The use of fiber-reinforced composite materials have increased in the last four decades in high technology applications due to their exceptional mechanical properties and low weight. In the automotive industry carbon fiber have become popular exclusively in luxury cars because of its high cost. However, Carbon-glass hybrid composites offer an effective alternative to designers to implement fiber-reinforced composites into several conventional applications without a considerable price increase maintaining most of their mechanical properties. A door latch system is a complex mechanism that is under high loading conditions during car accidents such as side impacts and rollovers. Therefore, the Department of Transportation in The United States developed a series of tests that every door latch system comply in order to be installed in a vehicle. The implementation of fiber-reinforced composite materials in a door latch system was studied by analyzing the material behavior during the FMVSS No. 206 transverse test using computational efforts and experimental testing. Firstly, a computational model of the current forkbolt and detent structure was developed. Several efforts were conducted in order to create an effective and time efficient model. Two simplified models were implemented with two different contact interaction approaches. 9 composite materials were studied in forkbolt and 5 in detent including woven carbon fiber, unidirectional carbon fiber, woven carbon-glass fiber hybrid composites and unidirectional carbon-glass fiber hybrid composites. The computational model results showed that woven fiber-reinforced composite materials were stiffer than the unidirectional fiber-reinforced composite materials. For instance, a forkbolt made of woven carbon fibers was 20% stiffer than a forkbolt made of unidirectional fibers symmetrically stacked in 0° and 90° alternating directions. Furthermore, Hybrid composite materials behaved as expected in forkbolt noticing a decline

Alternative fidelity measure between two states of an N-state quantum system

International Nuclear Information System (INIS)

Chen Jingling; Fu Libin; Zhao Xiangeng; Ungar, Abraham A.

2002-01-01

An alternative fidelity measure between two states of a qunit, an N-state quantum system, is proposed. It has a hyperbolic geometric interpretation, and it reduces to the Bures fidelity in the special case when N=2

Alternate mode for data acquisition and real-time monitoring system based on CAMAC system

International Nuclear Information System (INIS)

Luo, J.R.; Wei, P.J.; Li, G.M.; Wang, H.

2006-01-01

Long discharges (about 250 s) have been achieved on HT-7 tokamak experiments in the Institute of Plasma Physics, Chinese Academy of Sciences (ASIPP). And in the next generation tokamaks like ITER , KSTAR and EAST , the pulses will be about 1000 s. In such steady-state operation, we have to upgrade the CAMAC-based data acquisition system, with higher sampling rates and longer acquisition times. It is necessary to monitor the plasma parameters in real-time so that the operators can change the operational conditions during the discharge to maintain the plasma. A design of the system named alternant data acquisition and real-time monitoring system for steady-state tokamak operation based on CAMAC system has been setup in ASIPP. The application of this system has been demonstrated in the HT-7 and TRIAM-1M tokamaks during their 2004 experiment campaigns

The CEGB programme on comparative assessment of alternatives to hydrazine for oxygen removal from aqueous systems

International Nuclear Information System (INIS)

Case, B.; Wall, K.H.; Wates, R.W.

1994-01-01

The principal conclusion from the programme of work carried out by the CEGB was that Carbohydrazide appeared to be the most promising alternative to hydrazine for boiler feedwater conditioning. It is an effective oxygen scavenger at higher feedwater temperatures, its breakdown products are not a serious threat to circuit materials and it is safer to handle than hydrazine. The main disadvantages, at the time of the study, appeared to be the lack of a simple reliable method for measuring residual carbohydrazide in feedwater and a cost for the alternative chemical of up to 20 times that of hydrazine. (orig.)

48 CFR 252.242-7004 - Material management and accounting system.

Science.gov (United States)

2010-10-01

... CLAUSES Text of Provisions And Clauses 252.242-7004 Material management and accounting system. As prescribed in 242.7204, use the following caluse: Material Management and Accounting System (JUL 2009) (a) Definitions. As used in this clause— (1) Material management and accounting system (MMAS) means the Contractor...

Substitutional Reality System: A Novel Experimental Platform for Experiencing Alternative Reality

OpenAIRE

Suzuki, Keisuke; Wakisaka, Sohei; Fujii, Naotaka

2012-01-01

We have developed a novel experimental platform, referred to as a substitutional reality (SR) system, for studying the conviction of the perception of live reality and related metacognitive functions. The SR system was designed to manipulate people's reality by allowing them to experience live scenes (in which they were physically present) and recorded scenes (which were recorded and edited in advance) in an alternating manner without noticing a reality gap. All of the naïve participants (n =...

Structural materials for fusion reactor blanket systems

International Nuclear Information System (INIS)

Bloom, E.E.; Smith, D.L.

1984-01-01

Consideration of the required functions of the blanket and the general chemical, mechanical, and physical properties of candidate tritium breeding materials, coolants, structural materials, etc., leads to acceptable or compatible combinations of materials. The presently favored candidate structural materials are the austenitic stainless steels, martensitic steels, and vanadium alloys. The characteristics of these alloy systems which limit their application and potential performance as well as approaches to alloy development aimed at improving performance (temperature capability and lifetime) will be described. Progress towards understanding and improving the performance of structural materials has been substantial. It is possible to develop materials with acceptable properties for fusion applications

Proceedings - Alternate Fuels II: The disposal and productive use of industrial wastes

International Nuclear Information System (INIS)

Anon.

1991-01-01

The proceedings contain 26 papers dealing with the following topics: fuels (biomass, coal, petroleum coke, landfill gas, hazardous and toxic wastes, liquid wastes, and digester gas); combustion systems; plant systems (pollution control, combustion control, and materials handling systems); external factors (public relations, markets, hazardous waste, vitrification for waste management); and case histories of resource recovery facilities, process heating plants, and retrofits to alternative fuels. All papers have been processed separately for inclusion on the data base

[Establishment of traceability system of Chinese medicinal materials' quality].

Science.gov (United States)

Qi, Yao-dong; Gao, Shi-man; Liu, Hai-tao; Li, Xi-wen; Wei, Jian-he; Zhang, Ben-gang; Sun, Xiao-bo; Xiao, Pei-gen

2015-12-01

The quality of Chinese medicinal materials relates greatly to the clinical curative effect and security. In order to ensure the quality and safety of Chinese medicinal materials, a systematic and operable traceability system needs to be established. It can realize the whole process of quality and safety management of Chinese medicinal materials "from production to consumption" through recording and inquiring information and recalling defective products, which is an important direction for the future development of traditional Chinese medicine. But it is still at the exploration and trial stage. In this paper, a framework of Chinese medicinal materials' quality and safety traceability system was established on the basis of the domestic and international experience about the construction of food and agricultural products traceability systems. The relationship between traceability system of Chinese medicinal materials' quality and GAP, GMP, GSP was analyzed, and the possible problems and the corresponding solutions were discussed.

System for the fixation of radioactive and/or toxic waste materials

International Nuclear Information System (INIS)

Meier, G.

1975-01-01

In a bituminization process with a double-screw extruder aqueous concentrates, slimes, and resins are treated. In order to improve the operational safety in each evaporation nozzle the sight windows are purified with steam provided by a steam pipe and the areas of the nozzles bordering on the extrusion screws by means of steam lances mounted on a distribution. In addition, two alternately operable filters of, e.g. oil separating material are arranged in the connecting pipe between condenser and distillate collector in order to collect spatters of bitumen. During change of the receiving vessel for the mixed material, an interruption pot collecting the remains of the emerging mixed material is mounted on the filling nipple of the extruder. (DG/PB) [de

Beyond assemblies: system convergence and multi-materiality.

Science.gov (United States)

Wiscombe, Tom

2012-03-01

The architectural construction industry has become increasingly more specialized over the past 50 years, creating a culture of layer thinking over part-to-whole thinking. Building systems and technologies are often cobbled together in conflicting and uncorrelated ways, even when referred to as 'integrated', such as by way of building information modeling. True integration of building systems requires rethinking how systems and architectural morphologies can push and pull on one another, creating not only innovation in technology but in aesthetics. The revolution in composite materials, with unprecedented plasticity and performance features, opens up a huge range of possibilities for achieving this kind of convergence. Composites by nature fuse envelope and structure, but through various types of inflections, they can also be made to conduct air and fluids through cavities and de-laminations, as well as integrate lighting and energy systems. Assembly as we know it moves away from mineral materials and hardware and toward polymers and 'healing'. Further, when projected into the near-future realm of multi-materiality and 3D manufacturing, possibilities for embedding systems and creating gradients of rigidity and opacity open up, pointing to an entirely new realm of architectural thinking.

Beyond assemblies: system convergence and multi-materiality

International Nuclear Information System (INIS)

Wiscombe, Tom

2012-01-01

The architectural construction industry has become increasingly more specialized over the past 50 years, creating a culture of layer thinking over part-to-whole thinking. Building systems and technologies are often cobbled together in conflicting and uncorrelated ways, even when referred to as 'integrated', such as by way of building information modeling. True integration of building systems requires rethinking how systems and architectural morphologies can push and pull on one another, creating not only innovation in technology but in aesthetics. The revolution in composite materials, with unprecedented plasticity and performance features, opens up a huge range of possibilities for achieving this kind of convergence. Composites by nature fuse envelope and structure, but through various types of inflections, they can also be made to conduct air and fluids through cavities and de-laminations, as well as integrate lighting and energy systems. Assembly as we know it moves away from mineral materials and hardware and toward polymers and 'healing'. Further, when projected into the near-future realm of multi-materiality and 3D manufacturing, possibilities for embedding systems and creating gradients of rigidity and opacity open up, pointing to an entirely new realm of architectural thinking.

Material control test and evaluation system at the ICPP

International Nuclear Information System (INIS)

Johnson, C.E.

1979-01-01

The US DOE is evaluating process monitoring as part of a total nuclear material safeguards system. A monitoring system is being installed at the Idaho Chemical Processing Plant to test and evaluate material control and surveillance concepts in an operating nuclear fuel reprocessing plant. Process monitoring for nuclear material control complements conventional safeguards accountability and physical protection to assure adherence to approved safeguards procedures and verify containment of nuclear materials within the processing plant

Portable Thermoelectric Power Generator Coupled with Phase Change Material

OpenAIRE

Lim Chong C.; Al-Kayiem Hussain H.; Sing Chin Y.

2014-01-01

Solar is the intermittent source of renewable energy and all thermal solar systems having a setback on non-functioning during the night and cloudy environment. This paper presents alternative solution for power generation using thermoelectric which is the direct conversion of temperature gradient of hot side and cold side of thermoelectric material to electric voltage. Phase change material with latent heat effect would help to prolong the temperature gradient across thermoelectric material f...

Information systems for the materials management department: stand-alone and enterprise resource planning systems.

Science.gov (United States)

2005-03-01

Materials management information systems (MMISs) incorporate information tools that hospitals can use to automate certain business processes, increase staff compliance with these processes, and identify opportunities for cost savings. Recently, there has been a push by hospital administration to purchase enterprise resource planning (ERP) systems, information systems that promise to integrate many more facets of healthcare business. We offer this article to help materials managers, administrators, and others involved with information system selection understand the changes that have taken place in materials management information systems, decide whether they need a new system and, if so, whether a stand-alone MMIS or an ERP system will be the best choice.

Numerical simulations of electric potential field for alternating current potential drop associated with surface cracks in low-alloy steel nuclear material

Science.gov (United States)

Yeh, Chun-Ping; Huang, Jiunn-Yuan

2018-04-01

Low-alloy steels used as structural materials in nuclear power plants are subjected to cyclic stresses during power plant operations. As a result, cracks may develop and propagate through the material. The alternating current potential drop technique is used to measure the lengths of cracks in metallic components. The depth of the penetration of the alternating current is assumed to be small compared to the crack length. This assumption allows the adoption of the unfolding technique to simplify the problem to a surface Laplacian field. The numerical modelling of the electric potential and current density distribution prediction model for a compact tension specimen and the unfolded crack model are presented in this paper. The goal of this work is to conduct numerical simulations to reduce deviations occurring in the crack length measurements. Numerical simulations were conducted on AISI 4340 low-alloy steel with different crack lengths to evaluate the electric potential distribution. From the simulated results, an optimised position for voltage measurements in the crack region was proposed.

Alternative farrowing accommodation: welfare and economic aspects of existing farrowing and lactation systems for pigs.

Science.gov (United States)

Baxter, E M; Lawrence, A B; Edwards, S A

2012-01-01

There is growing societal pressure, expressed through government legislation and consumers' purchasing choices, to abolish livestock systems considered detrimental to farm animal welfare. Such systems include farrowing crates, which are behaviourally and physically restrictive for sows. Therefore, identifying less restrictive farrowing systems for commercial implementation has become an important focus of pig research. Despite numerous attempts to develop indoor alternatives to crates, there is as yet no universal acceptance of such systems at the commercial level. The primary concern is piglet survival, because often favourable figures are reported at the experimental level, but not replicated in commercial evaluation. Alternative farrowing systems should equal or surpass survival levels in conventional systems and perform consistently across a range of farm circumstances for widespread commercial implementation. In addition, it is important that alternatives consider ease of management, operator safety and economic sustainability. Utilising a large database of literature, 12 existing alternative indoor systems were identified and compared against each other, conventional crates and outdoor systems. An assessment of how well alternative systems satisfy the design criteria for meeting animals' biological needs was carried out by developing a welfare design index (WDI). The physical and financial performance of these systems was also evaluated and summarised. The derived WDI yielded values of 0.95 for conventional crates, with higher scores for commercial outdoor systems of 1.10 and indoor group farrowing or multi-suckling systems (e.g. Thorstensson = 2.20). However, the high total piglet mortality (23.7% ± s.e. 2.26) in indoor group systems compared with conventional crates (18.3% ± s.e. 0.63) and outdoor systems (17.0% ± s.e. 2.05), together with the added capital cost (92% more than conventional crates, 249% more than commercial outdoor huts), mainly as a

Structural materials challenges for fusion power systems

International Nuclear Information System (INIS)

Kurtz, Richard J.

2009-01-01

Full text: Structural materials in a fusion power system must function in an extraordinarily demanding environment that includes various combinations of high temperatures, reactive chemicals, time-dependent thermal and mechanical stresses, and intense damaging radiation. The fusion neutron environment produces displacement damage equivalent to displacing every atom in the material about 150 times during its expected service life, and changes in chemical composition by transmutation reactions, which includes creation of reactive and insoluble gases. Fundamental materials challenges that must be resolved to effectively harness fusion power include (1) understanding the relationships between material strength, ductility and resistance to cracking, (2) development of materials with extraordinary phase stability, high-temperature strength and resistance to radiation damage, (3) establishment of the means to control corrosion of materials exposed to aggressive environments, (4) development of technologies for large-scale fabrication and joining, and (5) design of structural materials that provide for an economically attractive fusion power system while simultaneously achieving safety and environmental acceptability goals. The most effective approach to solve these challenges is a science-based effort that couples development of physics-based, predictive models of materials behavior with key experiments to validate the models. The U.S. Fusion Materials Sciences program is engaged in an integrated effort of theory, modeling and experiments to develop structural materials that will enable fusion to reach its safety, environmental and economic competitiveness goals. In this presentation, an overview of recent progress on reduced activation ferritic/martensitic steels, nanocomposited ferritic alloys, and silicon carbide fiber reinforced composites for fusion applications will be given

14 CFR 21.125 - Production inspection system: Materials Review Board.

Science.gov (United States)

2010-01-01

... § 21.125 Production inspection system: Materials Review Board. Link to an amendment published at 74 FR... Materials Review Board action for at least two years. (b) The production inspection system required in § 21... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Production inspection system: Materials...

An evaluation of light water breeder reactor system (LWBR) as an alternative for nuclear power generation in Brazil

International Nuclear Information System (INIS)

Sauer, I.L.

1981-01-01

The LWBR system as an alternative for nuclear power generation in Brazil, was technically and economically evaluated. The LWBR system has been characterized comparatively with the Pressurized Water Reactors through technological and investment cost analysis and through the analysis of the processes and unit costs of the fuel cycle stages. The characteristics of the LWBR system in comparison to the PWR system, with respect to utilization and cumulative consumption of uranium and thorium resources, fuel cycle processes and associated costs have been determined for possible alternatives of nuclear power participation in the Brazilian hidro-thermal electricity generating system. The analysis concluded that the LWBR system does not represent an attractive alternative for nuclear power generation in Brazil and even has no potential to compete with conventional Pressurized Water Reactors. (Author) [pt

Pellet production from agricultural raw materials - A systems study

Energy Technology Data Exchange (ETDEWEB)

Nilsson, Daniel; Bernesson, Sven; Hansson, Per-Anders [Department of Energy and Technology, Swedish University of Agricultural Sciences, P.O. Box 7032, SE-75007 Uppsala (Sweden)

2011-01-15

The demand for biofuel pellets has increased considerably in recent years, causing shortage of the traditional raw materials sawdust and wood shavings. In this study, the costs and energy requirements for the production of pellets from agricultural raw materials were analysed. The materials studied were Salix, reed canary grass, hemp, straw, screenings, rape-seed meal, rape cake and distiller's waste. Four production scales were analysed, having an annual output of 80,000, 8000, 800 and 80 tonnes of pellets per year. It was concluded that the raw materials of greatest interest were Salix and reed canary grass. They had competitive raw material costs and acceptable fuel properties and could be mixed with sawdust in existing large-scale pelleting factories. Straw had low production costs but can cause serious ash-related problems and should, as also is the case for screenings, be avoided in small-scale burners. Hemp had high raw material costs and is of less commercial interest, while distiller's waste, rape-seed meal and rape cake had higher alternative values when used as protein feed. The scale of production had a crucial influence on production costs. The machinery was used much more efficiently in large-scale plants, resulting in clear cost savings. Small-scale pelleting, both static and mobile, required cheap raw materials, low labour costs and long utilisation times to be profitable. In most cases, briquetting would be more commercially viable. The energy use in manufacturing pellets from air-dried crops was generally no higher than when moist sawdust was used as the raw material. (author)

Subsurface barrier design alternatives for confinement and controlled advection flow

International Nuclear Information System (INIS)

Phillips, S.J.; Stewart, W.E.; Alexander, R.G.; Cantrell, K.J.; McLaughlin, T.J.

1994-02-01

Various technologies and designs are being considered to serve as subsurface barriers to confine or control contaminant migration from underground waste storage or disposal structures containing radioactive and hazardous wastes. Alternatives including direct-coupled flood and controlled advection designs are described as preconceptual examples. Prototype geotechnical equipment for testing and demonstration of these alternative designs tested at the Hanford Geotechnical Development and Test Facility and the Hanford Small-Tube Lysimeter Facility include mobile high-pressure injectors and pumps, mobile transport and pumping units, vibratory and impact pile drivers, and mobile batching systems. Preliminary laboratory testing of barrier materials and additive sequestering agents have been completed and are described

Propulsion System Materials Program semiannual progress report for April 1995 through September 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-04-01

Significant accomplishments in fabricating ceramic components for the DOE, NASA, and DOD advanced heat engine programs have provided evidence that the operation of ceramic parts in high-temperature engine environments is feasible. These programs have also demonstrated that additional research is needed in materials and processing development, design methodology, and data base and life prediction before industry will have a sufficient technology base from which to produce reliable cost-effective ceramic engine components commercially. An assessment of needs was completed, and a 5-year program plan was developed with extensive input from private industry. During the course of the Propulsion System Materials Program, remarkable progress has been made in the development of reliable structural ceramics. However, further work is needed to reduce the cost of ceramics to facilitate their commercial introduction, especially in the highly cost-sensitive automotive market. To this end, the direction of the Propulsion System Materials Program is now shifting toward reducing the cost of ceramics to facilitate commercial introduction of ceramic components for near-term engine applications. In response to extensive input from industry, the plan is to extend the engine types which were previously supported to include near-term (5--10 years) applications in conventional automobile and diesel truck engines. To facilitate the rapid transfer of this technology to US industry, the major portion of the work is being done in the ceramic industry, with technological support from government laboratories, other industrial laboratories, and universities. A systematic approach to reducing the cost of components is envisioned. The work elements are as follows: economic cost modeling, ceramic machining, powder synthesis, alternative forming and densification processes, yield improvement, system design studies, standards development, low-expansion ceramics, and testing and data base development.

Planning Support Systems (PSS-Based Spatial Plan Alternatives and Environmental Assessment

Directory of Open Access Journals (Sweden)

Hee-Sun Choi

2016-03-01

Full Text Available Spatial planning is at the core of national land and urban development. Many countries and cities seek sustainable development through various means such as coordinated environmental planning, environmental assessment, and internalization of environmental analysis and planning. A Planning Support System (PSS is a GIS (Geographic Information System-based, spatial decision-making support system that incorporates a variety of theories and pertinent models. This study adopted the “What if?” model to design an alternative spatial plan that includes generation of predictive scenarios and is relatively easy to use. In the cities studied, we identified a total of six scenarios based on the main drivers of development—namely, population and spatial policies. Subsequently, we assessed the alternatives for their environmental impact, preparing sensitivity maps for each major environmental issue in the target area (natural ecosystem, air and microclimate, natural disasters. One projected advantage of the “What if?” model is that its digital visualization of proposed plans may improve public awareness and involvement. Furthermore, the tool is expected to be highly useful in ensuring the objectivity of quantitative analyses. However, it is necessary to develop a PSS that is both standardized and tailored to the particular needs of each area. Finally, the development of an e-governance system will be beneficial in ensuring public access to the decision making process.

COST ANALYSIS OF ALTERNATIVE COMPUTERIZED SYSTEMS FOR THE MARKETING AND DISTRIBUTION OF MULTIPLE FOOD COMMODITIES

OpenAIRE

Epperson, James E.; Helmreich, D.P.; Moon, Leonard C.; Carley, Dale H.; Huang, Chung L.; Fletcher, Stanley M.

1981-01-01

The authors make cost comparisons among alternative computerized marketing systems. The systems described could encompass any number of commodities and stages of distribution involving cash and/or futures transactions.

FACADE SYSTEM MADE OF POROUS MATERIALS

Directory of Open Access Journals (Sweden)

Zhukov Aleksey Dmitrievich

2012-10-01

Full Text Available The proposed multi-component façade system is made of porous concretes employed both as bearing structures and for heat insulation and fireproofing purposes. The authors also provide their recommendations in respect of the mounting of the proposed façade system. The façade system considered in the article is composed of wall foam concrete blocks reinforced by basalt fibers (bearing elements of the structure, cellular concrete polystyrene (thermal insulation, and porous concrete (fireproofing and thermal insulation. Retained shuttering (in the fireproofing sections represents chrysolite cement sheets attached to the structures composed of glass-fiber plastic elements. The application of insulating porous concrete as a fireproofing material is based on the principle of adjustable stress-strained states of materials in the environment of variable pressure. This technology was developed at Moscow State University of Civil Engineering, and it was initially designated for the manufacturing of tailor-made products. The above concrete is also designated for retained shuttering and modified cavity masonry walls. Porous concrete that expands inside the fireproofing cavity ensures a tight contact both with the basic material and thermal insulation plates. The use of materials of the same origin (Portland cement means the formation of strong transition zones connecting the system components in the course of its hardening and further operation. The results of the thermotechnical calculation demonstrate that the thermal resistance registered on the surface of the wall that is 3 meters high (that has a 0.4 m fireproofing cavity is equal to 3.98 sq. m. C/Wt. The value of the coefficient of thermotechnical heterogeneity (r is equal to 0.86 with account for the thickness and thermal conductivity of point and linear elements. If the thermotechnical heterogeneity is taken into consideration, the thermal resistance of the proposed wall is equal to 3.42 m2 С/Wt.

Bioinspired Infrared Sensing Materials and Systems.

Science.gov (United States)

Shen, Qingchen; Luo, Zhen; Ma, Shuai; Tao, Peng; Song, Chengyi; Wu, Jianbo; Shang, Wen; Deng, Tao

2018-05-11

Bioinspired engineering offers a promising alternative approach in accelerating the development of many man-made systems. Next-generation infrared (IR) sensing systems can also benefit from such nature-inspired approach. The inherent compact and uncooled operation of biological IR sensing systems provides ample inspiration for the engineering of portable and high-performance artificial IR sensing systems. This review overviews the current understanding of the biological IR sensing systems, most of which are thermal-based IR sensors that rely on either bolometer-like or photomechanic sensing mechanism. The existing efforts inspired by the biological IR sensing systems and possible future bioinspired approaches in the development of new IR sensing systems are also discussed in the review. Besides these biological IR sensing systems, other biological systems that do not have IR sensing capabilities but can help advance the development of engineered IR sensing systems are also discussed, and the related engineering efforts are overviewed as well. Further efforts in understanding the biological IR sensing systems, the learning from the integration of multifunction in biological systems, and the reduction of barriers to maximize the multidiscipline collaborations are needed to move this research field forward. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Impacts of Western Area Power Administration's power marketing alternatives on electric utility systems

International Nuclear Information System (INIS)

Veselka, T.D.; Portante, E.C.; Koritarov, V.

1995-03-01

This technical memorandum estimates the effects of alternative contractual commitments that may be initiated by the Western Area Power Administration's Salt Lake City Area Office. It also studies hydropower operational restrictions at the Salt Lake City Area Integrated Projects in combination with these alternatives. Power marketing and hydropower operational effects are estimated in support of Western's Electric Power Marketing Environmental Impact Statement (EIS). Electricity production and capacity expansion for utility systems that will be directly affected by alternatives specified in the EIS are simulated. Cost estimates are presented by utility type and for various activities such as capacity expansion, generation, long-term firm purchases and sales, fixed operation and maintenance expenses, and spot market activities. Operational changes at hydropower facilities are also investigated

Diagnostics of materials and structures of heating system as a component of ecological management in a modern city

Directory of Open Access Journals (Sweden)

Verstina Natalia

2016-01-01

Full Text Available The maintenance of materials and structures of the underground space in modern cities which contains many engineering structures is considered in the article. It is claimed on the example of quantitative data that the underground structures exert a great influence on the ecological situation of the city. The matters of the research included the analysis of the main heating systems as the most responsible city structure; the conclusions obtained can be also used for smaller heat pipelines. The article includes the comparisons of modern technical methods of diagnostics of materials and heating systems structures according to the results of experiment, as well as the characteristic of norms of control of the materials condition at the stages of construction and maintenance applied in the developed countries. On this basis, the author has developed and presented a system of diagnostics taking into account the alternation of measures during the heating period as well as the season when heat supply is not required. For an effective ecological management in modern cities, it is suggested to create the automated data base of materials and structures of the heating systems on the basis of the developed scheme of their conditions and events, which needs to be used for forecasting of environmental risks and planning of recovery works with consideration of special features of the maintenance processes. The direction of the further research is defined: it is the expansion of the stated approaches on other types of underground communications in modern cities.

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics.

Science.gov (United States)

Eisenberg, Daniel A; Yu, Mengjing; Lam, Carl W; Ogunseitan, Oladele A; Schoenung, Julie M

2013-09-15

Copper-indium-gallium-selenium-sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS₂ p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane. Copyright © 2013 Elsevier B.V. All rights reserved.

Management system for regulating transport of radioactive material

International Nuclear Information System (INIS)

Lopez Vietri, Jorge; Capadona, Nancy; Barenghi, Leonardo

2008-01-01

Full text: The objective of this paper is to describe the main characteristics and fundamentals of the Nuclear regulatory Authority's (Autoridad Regulatoria Nuclear, ARN) management system applied to the regulation of transport of radioactive material, in Argentina. In the frame of ARN's quality policy, 'Protection against ionizing radiation on transport of radioactive materials' was selected as one of the regulatory processes, named TRM process from now on. ARN's quality management system is integrally based on ISO 9000 system addressed to help organizations in designing and implementing their quality management systems. TRM process was split into five sub processes in order to facilitate the implementation of quality system. Such sub processes were defined taking account of the main functions developed by ARN in the branch of safe transport of radioactive materials and are listed below: 1) Development and updating of standards and regulatory guides; 2) Licensing of packages, special radioactive materials and consignments of radioactive materials; 3) Compliance assurance during the transport of radioactive materials, and 4) Training, advising and communications. For each of these sub processes were specified their objectives, inputs, activities and outputs, the clients and stakeholders, responsibilities, supporting documents, control of documents and records, control of non-conformances, monitoring and measurements, audits, feedback and improvement. It was decided to develop a quality plan to organize and manage activities to meet quality requirements, to optimize the use of limited resources of the organization and to be used as a basis for monitoring and assessing compliance with the requirements, both internal and external. Supporting documents for sub processes were issued, validated, reviewed and improved as an essential point to implement continuous improving. Simultaneously, some indexes were defined to monitor and measure the sub processes as a way to show

Integration Workshop on Alternative Fuels in the EU Energy System, Petten, 22-23 November 2004. Summary Report

International Nuclear Information System (INIS)

Tzimas, E.; Peteves, S.D.

2005-01-01

The aim of the title Workshop was to: (a) provide information on the related Commission actions and policies, (b) assess key technological developments and describe the state of the art of alternative fuel technologies, and, (c) identify the techno-economic barriers associated with the introduction of alternative fuels in the EU energy system and more specifically, in its new Member States and Candidate Countries. The Workshop attracted a specialised audience of delegates from most of the New Member States and the Candidate Countries, who are directly involved with the preparation, development, implementation and monitoring of policies relevant to alternative fuels, as well as with related applied research and development. The Workshop facilitated the exchange of experiences and views among the participants on the optimal approaches that could lead to the successful introduction of alternative fuels in the energy system of each country. To this end, short informal presentations were solicited from each participating country about the prospective introduction of alternative fuels in their national energy system. These presentations were coupled by longer presentations made by experts on the following topics: The European Commission perspective on alternative fuels; A well-to-wheels assessment of alternative fuels; The European biomass potential, the prospects for biogas, and a review of advanced production methods for biofuels; An assessment of the European natural gas market, and a description of the state-of-the-art of natural gas vehicle technology. This report summarises the main points made by the participants, the outcome of the discussions and some thoughts on future actions that may be implemented by the JRC in support of initiatives taken by the New Member States and Candidate Countries concerning alternative fuels

Environmental considerations for alternative fusion reactor blankets

International Nuclear Information System (INIS)

Johnson, A.B. Jr.; Young, J.R.

1975-01-01

Comparisons of alternative fusion reactor blanket/coolant systems suggest that environmental considerations will enter strongly into selection of design and materials. Liquid blankets and coolants tend to maximize transport of radioactive corrosion products. Liquid lithium interacts strongly with tritium, minimizing permeation and escape of gaseous tritium in accidents. However, liquid lithium coolants tend to create large tritium inventories and have a large fire potential compared to flibe and solid blankets. Helium coolants minimize radiation transport, but do not have ability to bind the tritium in case of accidental releases. (auth)

[A medical consumable material management information system].

Science.gov (United States)

Tang, Guoping; Hu, Liang

2014-05-01

Medical consumables material is essential supplies to carry out medical work, which has a wide range of varieties and a large amount of usage. How to manage it feasibly and efficiently that has been a topic of concern to everyone. This article discussed about how to design a medical consumable material management information system that has a set of standardized processes, bring together medical supplies administrator, suppliers and clinical departments. Advanced management mode, enterprise resource planning (ERP) applied to the whole system design process.

Cultural alternatives. A material reading of the mourning of 11th-M / Alternativas de la cultura. Una lectura material del duelo del 11-M

Directory of Open Access Journals (Sweden)

Pilar Jimeno Salvatierra

2009-10-01

Full Text Available Since the human ecology approach occurs a break in the forms of studying culture or its accomplishments. The novelty has to do with the need to examine it not in itself or in their performances, but as an element of the ecological system is interconnected with the rest of their material elements. This material functional analysis model is described as a substantive by its main theoretical. Thus the cultural behaviours are responses to disturbances belonging to the system environment. One of the most interesting for the study of social and cultural are rituals, as part of retroactive mechanisms within any human ecological system. The aims of this paper is to theorize about the observation of the material aspects of collective behaviours, such as rituals, ceremonies, or others collective manifestations, that highlight the social importance and interpretative of these aspects. The article manifests both the creation and the orientation of “enactment of meanings” through the analysis of collective behaviours. It also shows an important part of social truth in material performances. Methodological applications such as Rappaport’s reference to material signs in his ritual theory, placing emphasize on the communication role of these are used to interpret the mourning ritual.

Island Megalopolises: Tunnel Systems as a Critical Alternative in Solving Transport Problems

Directory of Open Access Journals (Sweden)

Vladimir V. Makarov

2018-02-01

Full Text Available A principal difficulty with island megalopolises is the transport problem, which results from limited surface land on an already developed island, on which roads and car parking can be placed. This limitation leads to traffic jams on the small number of roads and to intrusive car parking in any available surface location, resulting in safety issues. The city of Vladivostok is located on the Muravyov-Amursky Peninsula in the Russia Far East region (the Primorsky Krai. This city is essentially the third capital of Russia because of its important geopolitical location. To address the car traffic problems in Vladivostok, and because of the absence of places to build new roads, the city administration has proposed the usage of the beaches and waterfronts along the sea coast in this regard. This decision is in sharp conflict with Vladivostok’s ecological and social aspirations to be recognized as a world-class city. It also neglects the lessons that have been learned in many other waterfront cities around the world, as such cities have first built aboveground waterfront highways and later decided to remove them at great expense, in order to allow their citizens to properly enjoy the environmental and historical assets of their waterfronts. A key alternative would be to create an independent tunneled transport system along with added underground parking so that the transport problems can be addressed in a manner that enhances the ecology and livability of the city. A comparison of the two alternatives for solving the transport problem, that is, underground versus aboveground, shows the significant advantages of the independent tunnel system. Complex efficiency criteria have been developed in order to quantify the estimation of the alternative variants of the Vladivostok transport system. It was determined that the underground project is almost 1.8 times more advantageous than the aboveground alternative. Keywords: Megalopolises, Transport, Tunnels

Alternative binder for copper concentrate briquetting

Directory of Open Access Journals (Sweden)

J. Łabaj

2015-10-01

Full Text Available In the paper, results of investigations on the use of new, alternative binder, based on technical grade glycerine and higher alcohols, for copper matte briquetting are presented. The use of alternative binder yields briquettes that show better drop and compressive strength properties compared with briquettes produced using traditional, sulphite lye binding material.

Materials and Systems for Organic Redox Flow Batteries: Status and Challenges

Energy Technology Data Exchange (ETDEWEB)

Wei, Xiaoliang [Joint Center for Energy Storage Research (JCESR), Argonne, Illinois 60439, United States; Energy & amp, Environment Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99354, United States; Pan, Wenxiao [Department; Duan, Wentao [Joint Center for Energy Storage Research (JCESR), Argonne, Illinois 60439, United States; Energy & amp, Environment Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99354, United States; Hollas, Aaron [Energy & amp, Environment Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99354, United States; Yang, Zheng [Joint Center for Energy Storage Research (JCESR), Argonne, Illinois 60439, United States; Energy & amp, Environment Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99354, United States; Li, Bin [Energy & amp, Environment Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99354, United States; Nie, Zimin [Energy & amp, Environment Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99354, United States; Liu, Jun [Joint Center for Energy Storage Research (JCESR), Argonne, Illinois 60439, United States; Energy & amp, Environment Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99354, United States; Reed, David [Energy & amp, Environment Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99354, United States; Wang, Wei [Energy & amp, Environment Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99354, United States; Sprenkle, Vincent [Energy & amp, Environment Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99354, United States

2017-08-14

Redox flow batteries are propitious stationary energy storage technologies with exceptional scalability and flexibility to improve the stability, efficiency and sustainability of our power grid. The redox-active materials are the central component to RFBs for achieving high energy density and good cyclability. Traditional inorganic-based materials encounter critical technical and economic limitations such as low solubility, inferior electrochemical activity, and high cost. Redox-active organic materials (ROMs) are promising alternative “green” candidates to push the boundaries of energy storage because of the significant advantages of molecular diversity, structural tailorability, and natural abundance. Here the recent development of a variety of ROM families and associated battery designs in both aqueous and nonaqueous electrolytes are reviewed. Moreover, the critical challenges and potential research opportunities for developing practically relevant organic flow batteries are discussed.

Materials Knowledge Systems in Python - A Data Science Framework for Accelerated Development of Hierarchical Materials.

Science.gov (United States)

Brough, David B; Wheeler, Daniel; Kalidindi, Surya R

2017-03-01

There is a critical need for customized analytics that take into account the stochastic nature of the internal structure of materials at multiple length scales in order to extract relevant and transferable knowledge. Data driven Process-Structure-Property (PSP) linkages provide systemic, modular and hierarchical framework for community driven curation of materials knowledge, and its transference to design and manufacturing experts. The Materials Knowledge Systems in Python project (PyMKS) is the first open source materials data science framework that can be used to create high value PSP linkages for hierarchical materials that can be leveraged by experts in materials science and engineering, manufacturing, machine learning and data science communities. This paper describes the main functions available from this repository, along with illustrations of how these can be accessed, utilized, and potentially further refined by the broader community of researchers.

SO2 Release as a Consequence of Alternative Fuel Combustion in Cement Rotary Kiln Inlets

DEFF Research Database (Denmark)

Cortada Mut, Maria del Mar; Nørskov, Linda Kaare; Glarborg, Peter

2015-01-01

The combustion of alternative fuels in direct contact with the bed material of the rotary kiln may cause local reducing conditions and, subsequently, decomposition of sulfates from cement raw materials, increasing the SO2 concentration in the gas phase. The decomposition of sulfates increases...... the sulfur circulation and may be problematic because high sulfur circulation can cause sticky material buildup, affecting the process operation of the cement kiln system. The SO2 release from cement raw materials during combustion of pine wood and tire rubber has been studied experimentally in a high...

Alternative Antimicrobial Approach: Nano-Antimicrobial Materials

OpenAIRE

Nurit Beyth; Yael Houri-Haddad; Avi Domb; Wahid Khan; Ronen Hazan

2015-01-01

Despite numerous existing potent antibiotics and other antimicrobial means, bacterial infections are still a major cause of morbidity and mortality. Moreover, the need to develop additional bactericidal means has significantly increased due to the growing concern regarding multidrug-resistant bacterial strains and biofilm associated infections. Consequently, attention has been especially devoted to new and emerging nanoparticle-based materials in the field of antimicrobial chemotherapy. The ...

Safeguards research: assessing material control and accounting systems

International Nuclear Information System (INIS)

Maimoni, A.

1977-01-01

The Laboratory is working for the Nuclear Regulatory Commission to improve the safeguarding of special nuclear material at nuclear fuel processing facilities, to provide a basis for improved regulations for material control and accounting systems, and to develop an assessment procedure for verifying compliance with these regulations. Early work included setting up a hierarchy of safeguard objectives and a set of measurable parameters with which systems performance to meet those objectives can be measured. Present work has focused on developing a computerized assessment procedure. We have also completed a test bed (based on a plutonium nitrate storage area) to identify and correct problems in the procedure and to show how this procedure can be used to evaluate the performance of an applicant's material control and accounting system

FEED SYSTEM INNOVATION FOR GASIFICATION OF LOCALLY ECONOMICAL ALTERNATIVE FUELS (FIGLEAF)

Energy Technology Data Exchange (ETDEWEB)

Michael L. Swanson; Mark A. Musich; Darren D. Schmidt; Joseph K. Schultz

2003-02-01

The Feed System Innovation for Gasification of Locally Economical Alternative Fuels (FIGLEAF) project was conducted by the Energy & Environmental Research Center and Gasification Engineering Corporation of Houston, Texas (a subsidiary of Global Energy Inc., Cincinnati, Ohio), with 80% cofunding from the U.S. Department of Energy (DOE). The goal of the project was to identify and evaluate low-value fuels that could serve as alternative feedstocks and to develop a feed system to facilitate their use in integrated gasification combined-cycle and gasification coproduction facilities. The long-term goal, to be accomplished in a subsequent project, is to install a feed system for the selected fuel(s) at Global Energy's commercial-scale 262-MW Wabash River Coal Gasification Facility in West Terre Haute, Indiana. The feasibility study undertaken for the project consisted of identifying and evaluating the economic feasibility of potential fuel sources, developing a feed system design capable of providing a fuel at 400 psig to the second stage of the E-Gas (Destec) gasifier to be cogasified with coal, performing bench- and pilot-scale testing to verify concepts and clarify decision-based options, reviewing information on high-pressure feed system designs, and determining the economics of cofeeding alternative feedstocks with the conceptual feed system design. A preliminary assessment of feedstock availability within Indiana and Illinois was conducted. Feedstocks evaluated included those with potential tipping fees to offset processing cost: sewage sludge, municipal solid waste, used railroad ties, urban wood waste (UWW), and used tires/tire-derived fuel. Agricultural residues and dedicated energy crop fuels were not considered since they would have a net positive cost to the plant. Based on the feedstock assessment, sewage sludge was selected as the primary feedstock for consideration at the Wabash River Plant. Because of the limited waste heat available for drying and

SYSTEM ORGANIZATION OF MATERIAL PROVIDING OF BUILDING

Directory of Open Access Journals (Sweden)

A. V. Rаdkеvich

2014-04-01

Full Text Available Purpose. Development of scientific-methodical bases to the design of rational management of material streams in the field of building providing taking into account intersystem connections with the enterprises of building industry. Methodology. The analysis of last few years of functioning of building industry in Ukraine allows distinguishing a number of problems that negatively influence the steady development of building, as the component of the state economics system. Therefore the research of existent organization methods of the system of building objects providing with material resources is extremely necessary. In connection with this the article justifies the use of method of hierarchies analysis (Saati method for finding the optimal task solution of fixing the enterprises of building industry after building objects. Findings. Results give an opportunity to guidance of building organization to estimate and choose advantageous suppliers - enterprises of building industry, to conduct their rating, estimation taking into account basic descriptions, such as: quality, price, reliability of deliveries, specialization, financial status etc. Originality. On the basis of Saati method the methodologies of organization are improved, planning and managements of the reliable system of providing of building necessary material resources that meet the technological requirements of implementation of building and installation works. Practical value. Contribution to the decisions of many intricate organizational problems that are accompanied by the problems of development of building, provided due to organization of the reliable system of purchase of material resources.

Value/impact analysis for evaluating alternative mitigation systems

International Nuclear Information System (INIS)

Kastenberg, W.E.; Catton, I.; Castle, J.N.; Dooley, J.L.; Hammond, R.P.

1988-01-01

Methods are developed for assessing the cost effectiveness of proposed systems and strategies for mitigating the consequences of severe nuclear accidents. Such mitigation systems consist mostly of devices for improving the ability of a reactor containment to survive such an accident and retain all radioactive materials. Value/impact analysis is applied to the system with and without mitigation, using the population dose averted by mitigation as the value of benefit, and the dollar cost of the containment improvements as the impact. Other considerations affecting such analyses include ways of monetizing public health risk, economic discounting, and the effect of interdiction policy and other post-accident recovery costs

Rapid architecture alternative modeling (RAAM): A framework for capability-based analysis of system of systems architectures

Science.gov (United States)

Iacobucci, Joseph V.

The research objective for this manuscript is to develop a Rapid Architecture Alternative Modeling (RAAM) methodology to enable traceable Pre-Milestone A decision making during the conceptual phase of design of a system of systems. Rather than following current trends that place an emphasis on adding more analysis which tends to increase the complexity of the decision making problem, RAAM improves on current methods by reducing both runtime and model creation complexity. RAAM draws upon principles from computer science, system architecting, and domain specific languages to enable the automatic generation and evaluation of architecture alternatives. For example, both mission dependent and mission independent metrics are considered. Mission dependent metrics are determined by the performance of systems accomplishing a task, such as Probability of Success. In contrast, mission independent metrics, such as acquisition cost, are solely determined and influenced by the other systems in the portfolio. RAAM also leverages advances in parallel computing to significantly reduce runtime by defining executable models that are readily amendable to parallelization. This allows the use of cloud computing infrastructures such as Amazon's Elastic Compute Cloud and the PASTEC cluster operated by the Georgia Institute of Technology Research Institute (GTRI). Also, the amount of data that can be generated when fully exploring the design space can quickly exceed the typical capacity of computational resources at the analyst's disposal. To counter this, specific algorithms and techniques are employed. Streaming algorithms and recursive architecture alternative evaluation algorithms are used that reduce computer memory requirements. Lastly, a domain specific language is created to provide a reduction in the computational time of executing the system of systems models. A domain specific language is a small, usually declarative language that offers expressive power focused on a particular

Alternative contract mechanisms for environmental restoration

International Nuclear Information System (INIS)

Billings, R.M.; Geotze, P.; Billings, B.G.

1994-01-01

Remediation and investigation contracting mechanisms used by Billings and Associates, Inc. (BAI), for operations within New Mexico are described, and the advantages and disadvantages are considered. Methods discussed are: time and materials, unit pricing, and pay for performance. An emphasis is placed upon the pay for performance method. While there are alternative contracting mechanisms, the state has thus far been limited to traditional contract types, such as time and materials. While the undertaking of a pay for performance remediation scenario presents higher risk with an opportunity for comparable reward, application of this type of alternative contracting has been slow to materialize. The New Mexico Environment Department/Underground Storage Tank Bureau is mandated by regulation to seek complete remediation of petroleum contaminated soils and ground water within the shortest practicable period of time

Application of macro material flow modeling to the decision making process for integrated waste management systems

International Nuclear Information System (INIS)

Vigil, S.A.; Holter, G.M.

1995-04-01

Computer models have been used for almost a decade to model and analyze various aspects of solid waste management Commercially available models exist for estimating the capital and operating costs of landfills, waste-to-energy facilities and compost systems and for optimizing system performance along a single dimension (e.g. cost or transportation distance). An alternative to the use of currently available models is the more flexible macro material flow modeling approach in which a macro scale or regional level approach is taken. Waste materials are tracked through the complete integrated waste management cycle from generation through recycling and reuse, and finally to ultimate disposal. Such an approach has been applied by the authors to two different applications. The STELLA simulation language (for Macintosh computers) was used to model the solid waste management system of Puerto Rico. The model incorporated population projections for all 78 municipalities in Puerto Rico from 1990 to 2010, solid waste generation factors, remaining life for the existing landfills, and projected startup time for new facilities. The Pacific Northwest Laboratory has used the SimScript simulation language (for Windows computers) to model the management of solid and hazardous wastes produced during cleanup and remediation activities at the Hanford Nuclear Site

Distinguishing the Effects of Bond-Length Alternation versus Bond-Order Alternation on the Nonlinear Optical Properties of π-Conjugated Chromophores

KAUST Repository

Gieseking, Rebecca L.; Risko, Chad; Bredas, Jean-Luc

2015-01-01

Understanding the relationships between the molecular nonlinear optical (NLO) properties and the bond-length alternation (BLA) or π-bond-order alternation (BOA) along the molecular backbone of linear π-conjugated systems has proven widely useful in the development of NLO organic chromophores and materials. Here, we examine model polymethines to elucidate the reliability of these relationships. While BLA is solely a measure of molecular geometric structure, BOA includes information pertaining to the electronic structure. As a result, BLA is found to be a good predictor of NLO properties only when optimized geometries are considered, whereas BOA is more broadly applicable. Proper understanding of the distinction between BLA and BOA is critical when designing computational studies of NLO properties, especially for molecules in complex environments or in nonequilibrium geometries. © 2015 American Chemical Society.

Distinguishing the Effects of Bond-Length Alternation versus Bond-Order Alternation on the Nonlinear Optical Properties of π-Conjugated Chromophores

KAUST Repository

Gieseking, Rebecca L.

2015-06-18

Understanding the relationships between the molecular nonlinear optical (NLO) properties and the bond-length alternation (BLA) or π-bond-order alternation (BOA) along the molecular backbone of linear π-conjugated systems has proven widely useful in the development of NLO organic chromophores and materials. Here, we examine model polymethines to elucidate the reliability of these relationships. While BLA is solely a measure of molecular geometric structure, BOA includes information pertaining to the electronic structure. As a result, BLA is found to be a good predictor of NLO properties only when optimized geometries are considered, whereas BOA is more broadly applicable. Proper understanding of the distinction between BLA and BOA is critical when designing computational studies of NLO properties, especially for molecules in complex environments or in nonequilibrium geometries. © 2015 American Chemical Society.

Application of BIM technology in green building material management system

Science.gov (United States)

Zhineng, Tong

2018-06-01

The current green building materials management system in China's construction industry is not perfect, and there are still many shortcomings. Active construction of green building materials management system based on BIM technology, combined with the characteristics of green building materials and its relationship with BIM technology application, is urgently needed to better realize the scientific management of green building materials.

Space Industry Commercialization: A Systems Engineering Evaluation of Alternatives

Science.gov (United States)