WorldWideScience

Sample records for materials involving selective

  1. Skateboard deck materials selection

    Science.gov (United States)

    Liu, Haoyu; Coote, Tasha; Aiolos; Charlie

    2018-03-01

    The goal of this project was to identify the ideal material for a skateboard deck under 200 in price, minimizing the weight. The material must have a fracture toughness of 5 MPa/m2, have a minimum lifetime of 10, 000 cycles and must not experience brittle fracture. Both single material and hybrid solutions were explored. When further selecting to minimize weight, woods were found to be the best material. Titanium alloy-wood composites were explored to determine the optimal percentage composition of each material.A sandwich panel hybrid of 50% titanium alloy and 50% wood (Ti-Wood) was found to be the optimum material, performing better than the currently used plywood.

  2. Materials selection in mechanical design

    International Nuclear Information System (INIS)

    Ashby, M.F.; Cebon, D.

    1993-01-01

    A novel materials-selection procedure has been developed and implemented in software. The procedure makes use of Materials Selection Charts: a new way of displaying material property data; and performance indices: combinations of material properties which govern performance. Optimisation methods are employed for simultaneous selection of both material and shape. (orig.)

  3. Materials selection in mechanical design

    OpenAIRE

    Ashby , M.; Cebon , D.

    1993-01-01

    A novel materials-selection procedure has been developed and implemented in software. The procedure makes use of Materials Selection Charts: a new way of displaying material property data; and performance indices: combinations of material properties which govern performance. Optimisation methods are employed for simultaneous selection of both material and shape.

  4. Materials selection for cutting tools

    International Nuclear Information System (INIS)

    Burkhis, Adel M.

    2008-01-01

    The selection of proper tool steel for a given application is a difficult task. So; the most important selection factors in choosing cutting tool materials are based on their tool material requirements, cutting tool design and service conditions which is mainly considered as functional requirements. The processability requirements concerns in heat treat ability of the material tool. The classification of these tool materials were discussed with their properties requirement and percent of alloying element which is added to give best properties with a little increase in cost that highly appear in comparison of the selection. The cutting tool materials were evaluated based on two cases; The first was in case of rough surface; the high speed steels is the best material and the other was the ceramic material is the highest performance in cutting of soft or high rate of metal removal. (author)

  5. Materials Selection for Aerospace Systems

    Science.gov (United States)

    Arnold, Steven M.; Cebon, David; Ashby, Mike

    2012-01-01

    A systematic design-oriented, five-step approach to material selection is described: 1) establishing design requirements, 2) material screening, 3) ranking, 4) researching specific candidates and 5) applying specific cultural constraints to the selection process. At the core of this approach is the definition performance indices (i.e., particular combinations of material properties that embody the performance of a given component) in conjunction with material property charts. These material selection charts, which plot one property against another, are introduced and shown to provide a powerful graphical environment wherein one can apply and analyze quantitative selection criteria, such as those captured in performance indices, and make trade-offs between conflicting objectives. Finding a material with a high value of these indices maximizes the performance of the component. Two specific examples pertaining to aerospace (engine blades and pressure vessels) are examined, both at room temperature and elevated temperature (where time-dependent effects are important) to demonstrate the methodology. The discussion then turns to engineered/hybrid materials and how these can be effectively tailored to fill in holes in the material property space, so as to enable innovation and increases in performance as compared to monolithic materials. Finally, a brief discussion is presented on managing the data needed for materials selection, including collection, analysis, deployment, and maintenance issues.

  6. Selection of refractory materials for pyrochemical processing

    International Nuclear Information System (INIS)

    Axler, K.M.; DePoorter, G.L.; Bagaasen, L.M.

    1991-01-01

    Several pyrochemical processing operations require containment materials that exhibit minimal chemical interactions with the system, good thermal shock resistance, and reusability. One example is Direct Oxide Reduction (DOR). DOR involves the conversion of PuO 2 to metal by an oxidation/reduction reaction with Ca metal. The reaction proceeds within a molten salt flux at temperatures above 800C. A combination of thermodynamics, system thermodynamic modeling, and experimental investigations are in use to select and evaluate potential containment materials

  7. Spectrally selective solar energy materials

    International Nuclear Information System (INIS)

    Sikkens, M.

    1981-01-01

    The performance and properties of spectrally selective materials are considered and, in particular, the selective absorption of solar radiation by free electrons is discussed, both in a homogeneous material in which these electrons are strongly scattered, and in a composite material consisting of small metal particles in a dielectric host. Such materials can be used as selective absorbers if they are deposited as a thin film onto a metal substrate, the latter providing the required low emittance. This type of selective surfaces is produced by reactive sputtering of Ni in an Ar/CH 4 gas mixture. This method can yield Ni films with a considerable carbon concentration. The carbon concentration can be varied over a wide range by adjusting the partial methane pressure. The associated experimental techniques are discussed. As the carbon concentration increases, the structure of the films changes from a Ni phase in which carbon is dissolved, via an intermediate Ni 3 C phase into an amorphous carbon phase with a high electrical resistivity in which small nickel particles are embedded. Both mechanisms of selective absorption by free electrons are observed and are found to be well described by rather simple models. The best selectivity is obtained at high carbon concentrations where the films consist of nickel particles in carbon. Depending on the film thickness and the substrate material, the solar absorptance varies between 0.78 and 0.90, while the thermal emittance varies between 0.025 and 0.04. Since the films are found to be stable at 400 0 C in vacuum, it appears that these films are good candidates for application in photothermal solar energy conversion at temperature levels around 200 0 C and higher. (Auth.)

  8. Europa Lander Material Selection Considerations

    Energy Technology Data Exchange (ETDEWEB)

    Tappan, Alexander S. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Heller, Mellisa [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-01-10

    Energetic materials (EMs, explosives, pyrotechnics, propellants) provide high-power output of high temperature reaction products. These products can be solid, liquid, or gaseous during reaction or after the products have equilibrated with the surroundings. For example, high explosives typically consist of carbon, hydrogen, nitrogen, and oxygen bonded within a single molecule, and produce almost exclusively gaseous products. Conversely, intermetallics consist of physical mixtures of metals and metalloids, and produce almost exclusively condensed products. Other materials such as pyrotechnics and propellants have intermediate behavior. All energetic materials react in a self-propagating manner that after ignition, does not necessarily require energy input from the surroundings. The range of reaction velocities can range from mm/s for intermetallics, to km/s for high explosives. Energetic material selection depends on numerous requirements specific to the needs of a system. High explosives are used for applications where high pressure gases are necessary for pushing or fracturing materials (e.g., rock, metal) or creating shock waves or air blast. Propellants are used to produce moderate-pressure, high-temperature products without a shock wave. Pyrotechnics are used to produce numerous effects including: high-temperature products, gases, light, smoke, sound, and others. Thermites are used to produce heat, high-temperature products, materials, and other effects that require condensed products. Intermetallics are used to produce high-temperature condensed products and materials, with very little gas production. Numerous categories of energetic materials exist with overlapping definitions, effects, and properties.

  9. Waste package materials selection process

    International Nuclear Information System (INIS)

    Roy, A.K.; Fish, R.L.; McCright, R.D.

    1994-01-01

    The office of Civilian Radioactive Waste Management (OCRWM) of the United States Department of Energy (USDOE) is evaluating a site at Yucca Mountain in Southern Nevada to determine its suitability as a mined geologic disposal system (MGDS) for the disposal of high-level nuclear waste (HLW). The B ampersand W Fuel Company (BWFC), as a part of the Management and Operating (M ampersand O) team in support of the Yucca Mountain Site Characterization Project (YMP), is responsible for designing and developing the waste package for this potential repository. As part of this effort, Lawrence Livermore National Laboratory (LLNL) is responsible for testing materials and developing models for the materials to be used in the waste package. This paper is aimed at presenting the selection process for materials needed in fabricating the different components of the waste package

  10. First-wall/blanket materials selection for STARFIRE tokamak reactor

    International Nuclear Information System (INIS)

    Smith, D.L.; Mattas, R.F.; Clemmer, R.G.; Davis, J.W.

    1980-01-01

    The development of the reference STARFIRE first-wall/blanket design involved numerous trade-offs in the materials selection process for the breeding material, coolant structure, neutron multiplier, and reflector. The major parameters and properties that impact materials selection and design criteria are reviewed

  11. Cristallini Material Review and Selection

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Nicholas [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Savina, Joseph [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Hebden, Andrew [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division

    2016-09-30

    The creation of a handheld unit to utilize the Cristallini method of uranium hexafluoride sampling requires the identification and qualification of suitable substrate materials. These materials will need to quickly and completely react with the process gas, resist vapor locking under vacuum, while being relatively inexpensive and homogeneous. Two forms of powdered alumina have been chosen for a head-to-head comparison during upcoming uranium hexafluoride tests. Both materials have shown ideal uptake characteristics during tungsten hexafluoride tests with a high loading capacity and no measureable breakthrough. They have also been shown to work well at vacuums below 10 Torr, are commercially available and inexpensive. In addition, two possible hydrogen fluoride trapping materials, sodium fluoride and saturated calcium carbonate, have been identified for further testing.

  12. Selection of materials for ETF

    International Nuclear Information System (INIS)

    Nygren, R.E.

    1980-01-01

    Repeated operation of a long burning, ignited plasma in ETF implies high exposure to an intense source of energetic particles and high energy (14.1 MeV) neutrons and presents a unique environment for materials in ETF compared with earlier tokamaks. Designing ETF (and FED) will provide many insights into reactor relevant design issues related to materials performance, particularly in components outside the first wall. This paper focuses primarily on how exposure to the plasma and radiation damage to materials infuence the design lifetime of particular components, including the first wall, armor, and TF coils. Also discussed are radiaton exposure limits for repair welding of the torus and for electrical materials used in RF and diagnostics

  13. Material selection for TFTR limiters

    International Nuclear Information System (INIS)

    Ulrickson, M.

    1980-10-01

    The requirements for the material to be used as the first surface of limiters in TFTR are that it: (1) withstand a heat flux of 1 kw/cm 2 for a pulse length of 1.5s and a duty cycle of 1/200 for 10 5 cycles, (2) withstand the thermal and electro-magnetic loads from 10 4 plasma current disruptions lasting about 200 μs, (3) generate impurities at a rate low enough to meet impurity control requirements (which depend on the atomic number of the material) for TFTR, and (4) have tritium retention characteristics consistent with tritium inventory requirements for TFTR. An extensive set of material tests using electron beams, neutral beams, and plasma bombardment have been carried out to identify materials which can meet the thermal requirements of the above

  14. Material selection and embodied energy

    CSIR Research Space (South Africa)

    Ampofo-Anti, N

    2010-11-01

    Full Text Available mix concrete apron Non reinforced, ready mix concrete strip foundation Non reinforced, ready mix ground floor slab Concrete block Modular, hollow concrete block Solid concrete block Finishes Floor screed Insulated ceiling panel Perlite... Predicting the embodied energy contribution of a single material is however not as easy as green building practices assume. As illustrated by the example in Box 1, the choice of a material implies the choice of integral constituents such as insulation...

  15. Microwave heating processes involving carbon materials

    Energy Technology Data Exchange (ETDEWEB)

    Menendez, J.A.; Arenillas, A.; Fidalgo, B.; Fernandez, Y.; Zubizarreta, L.; Calvo, E.G.; Bermudez, J.M. [Instituto Nacional del Carbon, CSIC, Apartado 73, 33080 Oviedo (Spain)

    2010-01-15

    Carbon materials are, in general, very good absorbents of microwaves, i.e., they are easily heated by microwave radiation. This characteristic allows them to be transformed by microwave heating, giving rise to new carbons with tailored properties, to be used as microwave receptors, in order to heat other materials indirectly, or to act as a catalyst and microwave receptor in different heterogeneous reactions. In recent years, the number of processes that combine the use of carbons and microwave heating instead of other methods based on conventional heating has increased. In this paper some of the microwave-assisted processes in which carbon materials are produced, transformed or used in thermal treatments (generally, as microwave absorbers and catalysts) are reviewed and the main achievements of this technique are compared with those obtained by means of conventional (non microwave-assisted) methods in similar conditions. (author)

  16. Electrical Breakdown Phenomena Involving Material Interfaces

    Science.gov (United States)

    2013-06-01

    create ozone through chemical reactions involving reactive species created by the electrical discharge [3]. The glow discharge breakdown in such...2. REPORT TYPE N/A 3. DATES COVERED - 4. TITLE AND SUBTITLE Investigation Of Pre-Ionization And Atmospheric Pulsed Discharge Plasma 5a...growth of the air discharge in the form of a conductive filament consisting of electrons and ions. This filament is created by temporal pulse that

  17. Selected advances in materials research

    International Nuclear Information System (INIS)

    Cunningham, J.E.

    1979-01-01

    Several findings emanating from materials research that should have a beneficial impact on technological advancement in the future are described. The report deals with the GRAPHNOL, a new class of high-temperature brazing alloy for joining refractory components, gel-sphere-pac process for manufacture of nuclear fuel, and noble-metal fuel cladding for service in radioisotope thermoelectric generators designed to provide auxiliary power aboard spacecraft for planetary exploration

  18. Incident involving radioactive material in steel scrap

    International Nuclear Information System (INIS)

    Drabova, D.; Matzner, J.; Prouza, Z.

    1998-01-01

    In early March of 1996, a wagon with steel scrap heading from the Czech Republic to Italy was returned as a strongly contaminated material. Based on the integral dose (dose rate 650 mGy/h in front of the wagon) and spectrometric measurement and evaluation, it was concluded that an unshielded cobalt-60 source (1.6 TBq) was present. The history of the event (notification, assessment, intervention planning, intervention) is highlighted and the lesson learned from the incident is discussed. (P.A.)

  19. Material selection for an aerospace component

    OpenAIRE

    Jönsson, Gustav

    2015-01-01

    In the world of today there is a drive for lighter and more effective products for various reasons e.g. reduced environmental impact, higher payload, fuel efficiency etc. There is also an expanding development of new materials for a large number of different applications. This makes it more and more difficult for engineers to make good material selections. This has led to the development of a large amount of material selection methods that require more or less effort to select material. An ef...

  20. Eco-Material Selection for Auto Bodies

    Energy Technology Data Exchange (ETDEWEB)

    Mayyas, Ahmad T [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Omar, Mohammed [Masdar Institute of Science & Technology; Hayajneh, Mohammed T. [Jordan University of Science and Technology

    2017-09-25

    In the last decades, majority of automakers started to include lightweight materials in their vehicles to meet hard environmental regulations and to improve fuel efficiency of their vehicles. As a result, eco-material selection for vehicles emerged as a new discipline under design for environment. This chapter will summarize methods of eco-material selections for automotive applications with more emphasis into auto-bodies. A set of metrics for eco-material selection that takes into account all economic, environmental and social factors will be developed using numerical and qualitative methods. These metrics cover products' environmental impact, functionality and manufacturability, in addition to the economic and societal factors.

  1. Selective nanoscale growth of lattice mismatched materials

    Science.gov (United States)

    Lee, Seung-Chang; Brueck, Steven R. J.

    2017-06-20

    Exemplary embodiments provide materials and methods of forming high-quality semiconductor devices using lattice-mismatched materials. In one embodiment, a composite film including one or more substantially-single-particle-thick nanoparticle layers can be deposited over a substrate as a nanoscale selective growth mask for epitaxially growing lattice-mismatched materials over the substrate.

  2. The materials selection in ITER and the first materials workshop

    International Nuclear Information System (INIS)

    Matera, R.; Barabash, V.; Kalinin, G.; Tanaka, S.

    1998-01-01

    The selection of materials and joining technologies to be used in ITER is a trade-off between multiple and often conflicting requirements derived from the unique features of the fusion environment. Materials selection must encompass a total engineering approach, by considering not only physical and mechanical properties, but also the components' manufacturing, their maintainability and reliability, and, finally, how they can be recycled or disposed of at the end of machine operation

  3. Variety of factors involved in selecting PV components

    International Nuclear Information System (INIS)

    Wiener, M.

    1996-01-01

    Although solar electricity has been used for over ten years in oil and gas applications, there still seems to be some confusion concerning the selection of components for solar electric systems. This paper reviews the design and selection of materials for solar arrays, batteries, and controls and cables. It also provides information on determining expected service life and overall system integration

  4. Material and process selection using product examples

    DEFF Research Database (Denmark)

    Lenau, Torben Anker

    2001-01-01

    The objective of the paper is to suggest a different procedure for selecting materials and processes within the product development work. The procedure includes using product examples in order to increase the number of alternative materials and processes that is considered. Product examples can c...... a search engine, and through hyperlinks can relevant materials and processes be explored. Realising that designers are very sensitive to user interfaces do all descriptions of materials, processes and products include graphical descriptions, i.e. pictures or computer graphics....

  5. Material and process selection using product examples

    DEFF Research Database (Denmark)

    Lenau, Torben Anker

    2002-01-01

    The objective of the paper is to suggest a different procedure for selecting materials and processes within the product development work. The procedure includes using product examples in order to increase the number of alternative materials and processes that is considered. Product examples can c...... a search engine, and through hyperlinks can relevant materials and processes be explored. Realising that designers are very sensitive to user interfaces do all descriptions of materials, processes and products include graphical descriptions, i.e. pictures or computer graphics....

  6. Quality criteria for phase change materials selection

    International Nuclear Information System (INIS)

    Vitorino, Nuno; Abrantes, João C.C.; Frade, Jorge R.

    2016-01-01

    Highlights: • Selection criteria of phase change materials for representative applications. • Selection criteria based on reliable solutions for latent heat transfer. • Guidelines for the role of geometry and heat transfer mechanisms. • Performance maps based on PCM properties, operating conditions, size and time scales. - Abstract: Selection guidelines are primary criterion for optimization of materials for specific applications in order to meet simultaneous and often conflicting requirements. This is mostly true for technologies and products required to meet the main societal needs, such as energy. In this case, gaps between supply and demand require strategies for energy conversion and storage, including thermal storage mostly based on phase change materials. Latent heat storage is also very versatile for thermal management and thermal control by allowing high storage density within narrow temperature ranges without strict dependence between stored thermal energy and temperature. Thus, this work addressed the main issues of latent heat storage from a materials selection perspective, based on expected requirements of applications in thermal energy storage or thermal regulation. Representative solutions for the kinetics of latent heat charge/discharge were used to derive optimization guidelines for high energy density, high power, response time (from fast response to thermal inertia), etc. The corresponding property relations were presented in graphical forms for a wide variety of prospective phase change materials, and for wide ranges of operating conditions, and accounting for changes in geometry and mechanisms.

  7. Optimal materials selection for bimaterial piezoelectric microactuators

    OpenAIRE

    Srinivasan, P.; Spearing, S.M.

    2008-01-01

    Piezoelectric actuation is one of the commonly employed actuation schemes in microsystems. This paper focuses on identifying and ranking promising active material/substrate combinations for bimaterial piezoelectric (BPE) microactuators based on their performance. The mechanics of BPE structures following simple beam theory assumptions available in the literature are applied to evolve critical performance metrics which govern the materials selection process. Contours of equal performance are p...

  8. Inventory of accidents and losses at sea involving radioactive material

    International Nuclear Information System (INIS)

    2001-09-01

    The present report describes the content of the inventory of accidents and losses at sea involving radioactive material. It covers accidents and losses resulting in the actual release of radioactive materials into the marine environment and also those which have the potential for release. For completeness, records of radioactive materials involved in accidents but which were recovered intact from the sea are also reported. Information on losses of sealed sources resulting in actual or potential release of activity to the marine environment nad of sealed sources that were recovered intact is also presented

  9. Selecting materialized views in a data warehouse

    Science.gov (United States)

    Zhou, Lijuan; Liu, Chi; Liu, Daxin

    2003-01-01

    A Data Warehouse contains lots of materialized views over the data provided by the distributed heterogeneous databases for the purpose of efficiently implementing decision-support or OLAP queries. It is important to select the right view to materialize that answer a given set of queries. In this paper, we have addressed and designed algorithm to select a set of views to materialize in order to answer the most queries under the constraint of a given space. The algorithm presented in this paper aim at making out a minimum set of views, by which we can directly respond to as many as possible user"s query requests. We use experiments to demonstrate our approach. The results show that our algorithm works better. We implemented our algorithms and a performance study of the algorithm shows that the proposed algorithm gives a less complexity and higher speeds and feasible expandability.

  10. Selection and challenges for LFR reactor materials

    Energy Technology Data Exchange (ETDEWEB)

    Weisenburger, A.; Jianu, A.; Del Giacco, M.; Fetzer, R.; Heinzel, A.; Mueller, G. [Karlsruhe Institute of Technology (KIT), Eggenstein-Leopoldshafen (Germany). Inst. for Pulsed Power and Microwave Technology

    2013-07-01

    Nuclear energy using Fast GenIV reactors can fulfil future demands concerning CO2 free, base load capability and sustainability. One of the most promising coolants especially due to its high thermal inertia is liquid lead (Pb). Since several years researches all over the world investigate this coolant and its impact on the reactor design and by that on the materials to be selected. The LEADER project, a follow up of ELSY, aims to design a prototypical demonstrator ALFRED and to continue with several design related aspects of the ELFR reactor. For a demonstrator the criteria of material selection are somewhat different to a commercial type like the ELFR. Material selection for ELFR of course considers all the aspects relevant for ALFRED plus the targeted burn up and the expected total dpa related damage especially of the fuel pins. In the past compatibility of structural material (steels like 316L, T91 and 15-15Ti (1.4970)) that can be employed for Pb cooled fast nuclear reactors were investigated in several EU projects like EUROTRANS and worldwide. Solubility of steel alloying elements like Ni, Fe, Cr is the driving force for the reduced corrosion resistance in contact with Pb. In-situ oxidation is the acknowledged measure to protect steels in Pb up to certain temperatures that are material dependent. Based on experiments and the derived temperature limits the average core outlet temperatures of ALFRED and the ELFR are set to 480 C. The most challenging conditions with respect to temperature are at the fuel assembly and the heat exchangers. For both, thin stable oxide scales with negligible reduction in heat transfer are the requested protection method. This presentation will give an overview on the selected materials for ALFRED and ELFR considering, beside pure compatibility, the influence of mechanical interaction like creep and fretting. (orig.)

  11. Transportation accidents/incidents involving radioactive materials (1971--1991)

    International Nuclear Information System (INIS)

    Cashwell, C.E.; McClure, J.D.

    1992-01-01

    The Radioactive Materials Incident Report (RMIR) database contains information on transportation-related accidents and incidents involving radioactive materials that have occurred in the United States. The RMIR was developed at Sandia National Laboratories (SNL) to support its research and development program efforts for the US Department of Energy (DOE). This paper will address the following topics: background information on the regulations and process for reporting a hazardous materials transportation incident, overview data of radioactive materials transportation accidents and incidents, and additional information and summary data on how packagings have performed in accident conditions

  12. Selection of plasma facing materials for ITER

    International Nuclear Information System (INIS)

    Ulrickson, M.; Barabash, V.; Chiocchio, S.

    1996-01-01

    ITER will be the first tokamak having long pulse operation using deuterium-tritium fuel. The problem of designing heat removal structures for steady state in a neutron environment is a major technical goal for the ITER Engineering Design Activity (EDA). The steady state heat flux specified for divertor components is 5 MW/m 2 for normal operation with transients to 15 MW/m 2 for up to 10 s. The selection of materials for plasma facing components is one of the major research activities. Three materials are being considered for the divertor; carbon fiber composites, beryllium, and tungsten. This paper discusses the relative advantages and disadvantages of these materials. The final section of plasma facing materials for the ITER divertor will not be made until the end of the EDA

  13. Occupational accidents involving biological material among public health workers.

    Science.gov (United States)

    Chiodi, Mônica Bonagamba; Marziale, Maria Helena Palucci; Robazzi, Maria Lúcia do Carmo Cruz

    2007-01-01

    This descriptive research aimed to recognize the occurrence of work accidents (WA) involving exposure to biological material among health workers at Public Health Units in Ribeirão Preto-SP, Brazil. A quantitative approach was adopted. In 2004, 155 accidents were notified by means of the Work Accident Communication (WAC). Sixty-two accidents (40%) involved exposure to biological material that could cause infections like Hepatitis and Aids. The highest number of victims (42 accidents) came from the category of nursing aids and technicians. Needles were responsible for 80.6% of accidents and blood was the biological material involved in a majority of occupational exposure cases. This subject needs greater attention, so that prevention measures can be implemented, which consider the peculiarities of the activities carried out by the different professional categories.

  14. First response to transportation emergencies involving radioactive materials

    International Nuclear Information System (INIS)

    1994-01-01

    This FEMA/DOE/DOT videocourse describes the basis for procedures to be used by emergency first responders for transportation accidents which involve radioactive materials. Various commercial and government sector radioactive materials shipment programs will be described and will include information about hazards and the elements of safety, proper first response actions, notification procedures, and state or federal assistance during emergencies. Primary audience: fire service and emergency management personnel

  15. Material selection for design, manufacturing and application

    International Nuclear Information System (INIS)

    Zaid, A.I.O.

    2011-01-01

    Developing a new engineering material product or changing an existing one requires new design selecting material and choosing appropriate and economical manufacturing processes. These three main factors play a great role on the performance of the product in service. These items are independent and should not be performed in isolation from each other. With the great advancement of technology in the last decade and with the greater number of engineering materials which are now available, together with the increasing pressure to produce more economic and get reliable products an integrated approach which considers design, material selection and the appropriate manufacturing process makes it easier to achieve the optimum product that combines the functional requirements with the reliability at competitive cost. These diverse activities or items are interdependent; therefore should not be considered in isolation from each other, for example, it is not sufficient that design of the product should satisfy the technical, safety and legal requirements, it must also be possible to be manufactured economically and to be sold at a competitive price and easily disposed at the end of its working life cycle. In this paper, the interaction of these items together in order to arrive to the optimum solution for a particular application are given and discussed. (author)

  16. Route selection for the transport of hazardous materials

    Energy Technology Data Exchange (ETDEWEB)

    Seiler, F A

    1988-12-01

    The factors governing the risk-weighted selection of routes for transport of hazardous materials are analyzed. Starting from a formulation for the total risk of these transports that assumes complete information, approximations for the more realistic case of partial and uncertain information are discussed. These approximations involve well-known risk assessment techniques and mathematical methods; among the latter, Monte Carlo calculations hold the most promise. The actual route selection is based on an index of total societal cost, evaluated for a set of potential routes. (author)

  17. Partnership Selection Involving Mixed Types of Uncertain Preferences

    Directory of Open Access Journals (Sweden)

    Li-Ching Ma

    2013-01-01

    Full Text Available Partnership selection is an important issue in management science. This study proposes a general model based on mixed integer programming and goal-programming analytic hierarchy process (GP-AHP to solve partnership selection problems involving mixed types of uncertain or inconsistent preferences. The proposed approach is designed to deal with crisp, interval, step, fuzzy, or mixed comparison preferences, derive crisp priorities, and improve multiple solution problems. The degree of fulfillment of a decision maker’s preferences is also taken into account. The results show that the proposed approach keeps more solution ratios within the given preferred intervals and yields less deviation. In addition, the proposed approach can treat incomplete preference matrices with flexibility in reducing the number of pairwise comparisons required and can also be conveniently developed into a decision support system.

  18. Emergency response planning for transport accidents involving radioactive materials

    International Nuclear Information System (INIS)

    1982-03-01

    The document presents a basic discussion of the various aspects and philosophies of emergency planning and preparedness along with a consideration of the problems which might be encountered in a transportation accident involving a release of radioactive materials. Readers who are responsible for preparing emergency plans and procedures will have to decide on how best to apply this guidance to their own organizational structures and will also have to decide on an emergency planning and preparedness philosophy suitable to their own situations

  19. Piezoelectric materials involved in road traffic applications test system

    International Nuclear Information System (INIS)

    Vazquez Rodriguez, M.; Jimenez Martinez, F.; Frutos, J. de

    2011-01-01

    The test bench system described in this paper performs experiments on piezoelectric materials used in road traffic applications, covering a range between 14 and 170 km/h, which is considered enough for testing under standard traffic conditions. A software has been developed to control the three phase induction motor driver and to acquire all the measurement data of the piezoelectric materials. The mass over each systems axis can be selected, with a limit of 60 kg over each wheel. The test bench is used to simulate the real behaviour of buried piezoelectric cables in road traffic applications for both light and heavy vehicles. This new test bed system is a powerful research tool and can be applied to determine the optimal installation and configuration of the piezoelectric cable sensors and opens a new field of research: the study of energy harvesting techniques based on piezoelectric materials. (Author) 10 refs.

  20. Central Lesions With Selective Semicircular Canal Involvement Mimicking Bilateral Vestibulopathy

    Directory of Open Access Journals (Sweden)

    Luke Chen

    2018-04-01

    Full Text Available Bilateral vestibulopathy (BVP, which is due to peripheral lesions, may selectively involve certain semicircular canal (SCC. Recent eye movement recordings with search coil and video head impulse test (HIT have provided insight in central lesions that can cause bilateral and selective SCC deficit mimicking BVP. Since neurological signs or ocular motor deficits maybe subtle or absent, it is critical to recognize central lesions correctly since there is prognostic and treatment implication. Acute floccular lesions cause bilateral horizontal SCC (HC impairment while leaving vertical SCC function unaffected. Vestibular nuclear lesions affect bilateral HC and posterior SCC (PC function, but anterior SCC (AC function is spared. When both eyes are recorded, medial longitudinal fasciculus lesions cause horizontal dysconjugacy in HC function and catch-up saccades, as well as selective deficiency of PC over AC function. Combined peripheral and central lesions may be difficult to distinguish from BVP. Anterior inferior cerebellar artery stroke causes two types of deficits: 1. ipsilateral pan-SCC deficits and contralateral HC deficit and 2. bilateral HC deficit with vertical SCC sparing. Metabolic disorders such as Wernicke encephalopathy characteristically involve HC but not AC or PC function. Gaucher disease causes uniform loss of all SCC function but with minimal horizontal catch-up saccades. Genetic cerebellar ataxias and cerebellar-ataxia neuropathy vestibular areflexia syndrome typically do not spare AC function. While video HIT does not replace the gold-standard, search coil HIT, clinicians are now able to rapidly and accurately identify specific pattern of SCC deficits, which can aid differentiation of central lesions from BVP.

  1. Operational procedure standard for occurrences involving radioactive materials

    International Nuclear Information System (INIS)

    Piekarz, Leonardo; Rezende, Talita C.; Pinheiro, Christiano J.G.

    2017-01-01

    This study has as objective to analyze more deeply the actions of response to emergencies involving radioactive materials, in the intent to establish a pattern to the actions performed by the military fire fighters of the Military Fire Brigade of Minas Gerais. To met these goals, it has been attempted to analyze the procedures utilized and recommended, nowadays, for the military fire fighters of CBMMG, and through directed studies, to suggest new actions possible to be executed in the local of the emergency in a way that will not expose the garrison to doses of ionizing radiation that may prejudice them. It is a study of bibliographic, exploratory, and also descriptive nature, realized through a qualitative approach. The techniques used for the research were the analysis of institutional documents, norms and other literature produced by renamed entities in the radiologic and biosafety areas. It was then concluded that CBMMG, through simple actions of response, can provide higher quality and safety in the operations involving radiologic accidents, standing out that the implemented actions nowadays are very beneath the capacity of the corporation, due to the lack of knowledge of the matter by the fire fighters. It was proposed, then, that new actions be implemented and instituted as operational procedures to be used on those emergencies, with the objective of provide a higher safety and professionalism in the attendance to emergencies involving radioactive materials. (author)

  2. Operational procedure standard for occurrences involving radioactive materials

    Energy Technology Data Exchange (ETDEWEB)

    Piekarz, Leonardo, E-mail: leonardopbm@yahoo.com.br [Academia de Bombeiros Militar de Minas Gerais, Belo Horizonte, MG (Brazil); Rezende, Talita C.; Pinheiro, Christiano J.G., E-mail: talitacolombi@yahoo.com, E-mail: christrieste@yahoo.it [Universidade Federal do Espirito Santo (CCA/UFES), Alegre, ES (Brazil). Programa de Pós-Graduação em Engenharia Química

    2017-07-01

    This study has as objective to analyze more deeply the actions of response to emergencies involving radioactive materials, in the intent to establish a pattern to the actions performed by the military fire fighters of the Military Fire Brigade of Minas Gerais. To met these goals, it has been attempted to analyze the procedures utilized and recommended, nowadays, for the military fire fighters of CBMMG, and through directed studies, to suggest new actions possible to be executed in the local of the emergency in a way that will not expose the garrison to doses of ionizing radiation that may prejudice them. It is a study of bibliographic, exploratory, and also descriptive nature, realized through a qualitative approach. The techniques used for the research were the analysis of institutional documents, norms and other literature produced by renamed entities in the radiologic and biosafety areas. It was then concluded that CBMMG, through simple actions of response, can provide higher quality and safety in the operations involving radiologic accidents, standing out that the implemented actions nowadays are very beneath the capacity of the corporation, due to the lack of knowledge of the matter by the fire fighters. It was proposed, then, that new actions be implemented and instituted as operational procedures to be used on those emergencies, with the objective of provide a higher safety and professionalism in the attendance to emergencies involving radioactive materials. (author)

  3. Selection, development and characterisation of plasma facing materials for ITER

    International Nuclear Information System (INIS)

    Barabash, V.; Akiba, M.; Ulrickson, M.; Vieider, G.

    1996-01-01

    The current status of the selection of the armour materials for first wall, limiters and divertor are presented. The candidate armour materials are beryllium, tungsten and carbon base materials (mainly carbon fiber composites). The selection of the references grades from these material classes is discussed and the candidate grades are described. The main reasons for the selection of the reference grades are also discussed. The urgent materials R and D needs for the development of the design are described briefly. (orig.)

  4. Tools for Material Design and Selection

    Science.gov (United States)

    Wehage, Kristopher

    The present thesis focuses on applications of numerical methods to create tools for material characterization, design and selection. The tools generated in this work incorporate a variety of programming concepts, from digital image analysis, geometry, optimization, and parallel programming to data-mining, databases and web design. The first portion of the thesis focuses on methods for characterizing clustering in bimodal 5083 Aluminum alloys created by cryomilling and powder metallurgy. The bimodal samples analyzed in the present work contain a mixture of a coarse grain phase, with a grain size on the order of several microns, and an ultra-fine grain phase, with a grain size on the order of 200 nm. The mixing of the two phases is not homogeneous and clustering is observed. To investigate clustering in these bimodal materials, various microstructures were created experimentally by conventional cryomilling, Hot Isostatic Pressing (HIP), Extrusion, Dual-Mode Dynamic Forging (DMDF) and a new 'Gradient' cryomilling process. Two techniques for quantitative clustering analysis are presented, formulated and implemented. The first technique, the Area Disorder function, provides a metric of the quality of coarse grain dispersion in an ultra-fine grain matrix and the second technique, the Two-Point Correlation function, provides a metric of long and short range spatial arrangements of the two phases, as well as an indication of the mean feature size in any direction. The two techniques are implemented on digital images created by Scanning Electron Microscopy (SEM) and Electron Backscatter Detection (EBSD) of the microstructures. To investigate structure--property relationships through modeling and simulation, strategies for generating synthetic microstructures are discussed and a computer program that generates randomized microstructures with desired configurations of clustering described by the Area Disorder Function is formulated and presented. In the computer program, two

  5. ARTIFICIAL NEURAL NETWORKS BASED GEARS MATERIAL SELECTION HYBRID INTELLIGENT SYSTEM

    Institute of Scientific and Technical Information of China (English)

    X.C. Li; W.X. Zhu; G. Chen; D.S. Mei; J. Zhang; K.M. Chen

    2003-01-01

    An artificial neural networks(ANNs) based gear material selection hybrid intelligent system is established by analyzing the individual advantages and weakness of expert system (ES) and ANNs and the applications in material select of them. The system mainly consists of tow parts: ES and ANNs. By being trained with much data samples,the back propagation (BP) ANN gets the knowledge of gear materials selection, and is able to inference according to user input. The system realizes the complementing of ANNs and ES. Using this system, engineers without materials selection experience can conveniently deal with gear materials selection.

  6. Security of material: Preventing criminal activities involving nuclear and other radioactive materials

    International Nuclear Information System (INIS)

    Nilsson, A.

    2001-01-01

    The report emphasizes the need for national regulatory authorities to include in the regulatory systems, measures to control and protect nuclear materials from being used in illegal activities, as well as aspects of relevance for detecting and responding to illegal activities involving nuclear and other radioactive materials. The report will give an overview of the international treaties and agreements that underpin the establishment of a regulatory structure necessary for States to meet their non-proliferation policy and undertakings. Ongoing work to strengthen the protection of nuclear material and to detect and respond to illegal activities involving nuclear and other radioactive material will be included. The focus of the paper is on the need for standards and national regulation in the nuclear security area. (author)

  7. Selection of nuclear reactor coolant materials

    International Nuclear Information System (INIS)

    Shi Lisheng; Wang Bairong

    2012-01-01

    Nuclear material is nuclear material or materials used in nuclear industry, the general term, it is the material basis for the construction of nuclear power, but also a leader in nuclear energy development, the two interdependent and mutually reinforcing. At the same time, nuclear materials research, development and application of the depth and breadth of science and technology reflects a nation and the level of the nuclear power industry. Coolant also known as heat-carrier agent, is an important part of the heart nuclear reactor, its role is to secure as much as possible to the economic output in the form fission energy to heat the reactor to be used: the same time cooling the core, is controlled by the various structural components allowable temperature. This paper described the definition of nuclear reactor coolant and characteristics, and then addressed the requirements of the coolant material, and finally were introduced several useful properties of the coolant and chemical control. (authors)

  8. Selective Recovery of Critical Materials from Geothermal Fluid

    Energy Technology Data Exchange (ETDEWEB)

    Mayes, Richard T. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Halstenberg, Phillip W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Moyer, Bruce A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Karamalidis, Athanasios [Anactisis, LLC, Pittsburgh, PA (United States); Noack, Clint [Anactisis, LLC, Pittsburgh, PA (United States)

    2018-03-08

    This project, funded by the DOE Small Business Voucher program, assisted the partner with the development of ion-imprinted adsorbents for the selective extraction of rare earth elements (REE) from geothermal brines. This effort seeks to utilize a currently untapped resource thus diversifying the U. S. REE market. The initial stage of the program focused on the adsorbent developed by partner and optimization of the adsorbent. The adsorbent was based upon an ion imprinted ligand that was copolymerized with a crosslinker to generate the REE selectivity. During this task, the adsorbents were irradiated via electron beam at the NEO Beam Electron Beam Crosslinking Facility (Mercury Plastics, Middlefield, OH) to induce further crosslinking. The irradiation crosslinked adsorbents exhibited no difference in the Fourier transform infrared spectroscopic (FTIR) analysis suggesting inefficiency in the crosslinking. In the later stage of the effort, a new method was proposed and studied at ORNL involving a new partnership between the partner and a commercial polymer vender. This resulted in a new material being developed which allows the partner to utilize a commercial support and integrate the synthesis into a production-ready product stream. This will enhance the route to commercialization for the partner resulting in a quicker market penetration for the product. The new adsorbent exhibits selectivity for REE over transition metals commonly found within geothermal brines. Further optimization is required for enhanced selectivity, capacity, and intra-lanthanide separations.

  9. Radioactive waste - a select list of material

    International Nuclear Information System (INIS)

    Lambert, C.M.

    1982-01-01

    A chronological bibliography is presented of literature relating to radioactive waste management in the United Kingdom concentrating on material published since 1978. The main sections include Dept. of Environ. and Official publications, administrative and environmental concerns, technological and scientific considerations, including publications on geological aspects, deep-sea bed and ocean-dumping and salt domes, with general background material and further sources of information listed at the end. (U.K.)

  10. Material Selection for a Manual Winch Rope Drum

    OpenAIRE

    Moses F. Oduori; Enoch K. Musyoka; Thomas O. Mbuya

    2016-01-01

    The selection of materials is an essential task in mechanical design processes. This paper sets out to demonstrate the application of analytical decision making during mechanical design and, particularly, in selecting a suitable material for a given application. Equations for the mechanical design of a manual winch rope drum are used to derive quantitative material performance indicators, which are then used in a multiple attribute decision making (MADM) model to rank the candidate materials....

  11. Selecting suitable enclosures for digitally printed materials

    International Nuclear Information System (INIS)

    Burge, D; Rima, L

    2010-01-01

    It cannot be assumed that storage enclosures considered safe for traditionally printed images and documents are suitable for modern, digitally printed materials. In this project, a large variety of digital print types were tested using a modified version of the ISO 18916 Imaging materials-Processed imaging materials-Photographic activity test for enclosure materials standard to assess the risk to digital prints by paper enclosures known to be inert or reactive with traditional photographic prints. The types of enclosures tested included buffered and non-buffered cotton papers, and groundwood paper. In addition, qualitative filter paper that had been wetted and dried with either an acidic or basic solution was also tested to determine the effects of enclosure pH on digitally printed materials. It was determined that, in general, digital prints tended to be less reactive with various enclosure types than traditional prints. Digital prints were most sensitive to paper that contained groundwood. The enclosure reactivity test results were then integrated with previous published work on the tendencies of various enclosure types to abrade, ferrotype, or block to digital prints in order to create a comprehensive set of recommendations for digital print storage enclosures.

  12. SELECTED INSTRUCTIONAL MATERIALS FOR DISTRIBUTIVE EDUCATION.

    Science.gov (United States)

    LEVENDOWSKI, J.C.

    CITATIONS SUPPLEMENTING BULLETIN NO. 5, "DISTRIBUTIVE EDUCATION LIBRARY LIST," (ED 012 778) WERE SELECTED FOR DISTRIBUTIVE TEACHER EDUCATORS, ADULT INSTRUCTORS AND TEACHER COORDINATORS. THE PUBLICATIONS ARE FREE OR INEXPENSIVE BROCHURES, BULLETINS, PAMPHLETS AND PAPERBACK BOOKS, LISTED BY TOPICS--(1) "ADVERTISING AND DISPLAY," (2) "DISTRIBUTIVE…

  13. Sustainable material selection for construction industry

    DEFF Research Database (Denmark)

    Govindan, Kannan; Shankar, Madan; Kannan, Devika

    2016-01-01

    a hybrid multi criteria decision making (MCDM) methodology with a specific examination of the UAE. The indicators collected from existing literatures were used in evaluation of sustainable construction materials with the assistance of construction sector-based respondents. The proposed framework...

  14. Skin Cancer Education Materials: Selected Annotations.

    Science.gov (United States)

    National Cancer Inst. (NIH), Bethesda, MD.

    This annotated bibliography presents 85 entries on a variety of approaches to cancer education. The entries are grouped under three broad headings, two of which contain smaller sub-divisions. The first heading, Public Education, contains prevention and general information, and non-print materials. The second heading, Professional Education,…

  15. Implications of material selection on the design of packaging machinery.

    Science.gov (United States)

    Merritt, J P

    2009-01-01

    Material selection has significant implications on the design and cost of horizontal-form-fill-seal packaging machinery. To avoid excessive costs, machine redesigns and project delays, material selection must be reconciled early in the project and revisited throughout the construction of the machine.

  16. ABOUT INDEX EVALUATION OF MATERIAL RESOURCE SUPPLIER SELECTION

    OpenAIRE

    V. A. Skochinskaya

    2008-01-01

    The paper analyzes existing methods for evaluation of material resource supplier selection. It shows advantages and shortcomings of the present evaluation systems. The necessity for application of an index evaluation is justified in the paper. The paper contains rating (index) evaluation for material resource supplier selection which is based on the application of quantitative (index) tool instead of an expert (numerical) evaluation. 

  17. Views of pharmacists on involvement in ward rounds in selected ...

    African Journals Online (AJOL)

    Background: Pharmacist participation in ward rounds is of increasing interest for better pharmaceutical care, yet most pharmacists do not engage in this activity. Objective: The objective was to obtain public sector pharmacistsf views and perceptions on their involvement in ward rounds. Method: A rapid assessment was ...

  18. Processing and analysis techniques involving in-vessel material generation

    Science.gov (United States)

    Schabron, John F [Laramie, WY; Rovani, Jr., Joseph F.

    2012-09-25

    In at least one embodiment, the inventive technology relates to in-vessel generation of a material from a solution of interest as part of a processing and/or analysis operation. Preferred embodiments of the in-vessel material generation (e.g., in-vessel solid material generation) include precipitation; in certain embodiments, analysis and/or processing of the solution of interest may include dissolution of the material, perhaps as part of a successive dissolution protocol using solvents of increasing ability to dissolve. Applications include, but are by no means limited to estimation of a coking onset and solution (e.g., oil) fractionating.

  19. Raw material selection for object construction

    CSIR Research Space (South Africa)

    Perlow, J

    2017-11-01

    Full Text Available on their visual appearance. In particular, we present a method for an agent to recognise the required unseen raw material images and link them to corresponding novel object images. This capability provides an agent with an increased degree of resourcefulness... construction from component parts, and in doing so we provide a benchmark for future work to compare against within Minecraft and ShapeNet domains. II. BACKGROUND Our model is inspired by Siamese neural networks, a class of neural network that includes multiple...

  20. Basic Thermal Parameters of Selected Foods and Food Raw Materials

    OpenAIRE

    Monika Božiková; Ľubomír Híreš; Michal Valach; Martin Malínek; Jan Mareček

    2017-01-01

    In general, processing and manipulation with foods and food raw materials have significant influence on their physical properties. The article is focused on thermophysical parameters measurement of selected foods and food raw materials. There were examined thermal conductivity and thermal diffusivity of selected materials. For detection of thermal parameters was used instrument Isomet 2104, which principle of measurement is based on transient methods. In text are presented summary results of ...

  1. The Selection of Bridge Materials Utilizing the Analytical Hierarchy Process

    Science.gov (United States)

    Robert L. Smith; Robert J. Bush; Daniel L. Schmoldt

    1997-01-01

    Effective decisions on the use of natural resources often require the input of many individuals. Determining how specific criteria affect the selection of materials can lead to better utilization of raw materials. Concrete, steel, and timber represent over 98% of the materials used for bridge construction in the United States. Highway officials must often consider...

  2. Criteria for the selection of PEC primary circuit structural material

    International Nuclear Information System (INIS)

    Antoni, R.; Brunori, G.; Maesa, S.; Scibona, G.; Tomassetti, G.

    1977-01-01

    The choice of the structural materials is generally a compromise between the project requirements, the characteristics (mechanical and environmental) of the materials and the available technology to construct the various parts of the components. The criteria of selection of structural materials for the primary circuit of fast reactor are reported. The criteria concern both general and utilization aspects

  3. Surface analysis of selected hydrophobic materials

    Science.gov (United States)

    Wisniewska, Sylwia Katarzyna

    This dissertation contains a series of studies on hydrophobic surfaces by various surface sensitive techniques such as contact angle measurements, Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and atomic force microscopy (AFM). Hydrophobic surfaces have been classified as mineral surfaces, organic synthetic surfaces, or natural biological surfaces. As a model hydrophobic mineral surface, elemental sulfur has been selected. The sulfur surface has been characterized for selected allotropic forms of sulfur such as rhombic, monoclinic, plastic, and cyclohexasulfur. Additionally, dextrin adsorption at the sulfur surface was measured. The structure of a dextrin molecule showing hydrophobic sites has been presented to support the proposed hydrophobic bonding nature of dextrin adsorption at the sulfur surface. As a model organic hydrophobic surface, primary fatty amines such as dodecylamine, hexadecylamine, and octadecylamine were chosen. An increase of hydrophobicity, significant changes of infrared bands, and surface topographical changes with time were observed for each amine. Based on the results it was concluded that hydrocarbon chain rearrangement associated with recrystallization took place at the surface during contact with air. A barley straw surface was selected as a model of biological hydrophobic surfaces. The differences in the contact angles for various straw surfaces were explained by the presence of a wax layer. SEM images confirmed the heterogeneity and complexity of the wax crystal structure. AFM measurements provided additional structural details including a measure of surface roughness. Additionally, straw degradation as a result of conditioning in an aqueous environment was studied. Significant contact angle changes were observed as soon as one day after conditioning. FTIR studies showed a gradual wax layer removal due to straw surface decomposition. SEM and AFM images revealed topographical changes and biological

  4. Sorption analyses in materials science: selected oxides

    International Nuclear Information System (INIS)

    Fuller, E.L. Jr.; Condon, J.B.; Eager, M.H.; Jones, L.L.

    1981-01-01

    Physical adsorption studies have been shown to be extremely valuable in studying the chemistry and structure of dispersed materials. Many processes rely on the access to the large amount of surface made available by the high degree of dispersion. Conversely, there are many applications where consolidation of the dispersed solids is required. Several systems (silica gel, alumina catalysts, mineralogic alumino-silicates, and yttrium oxide plasters) have been studied to show the type and amount of chemical and structural information that can be obtained. Some review of current theories is given and additional concepts are developed based on statistical and thermodynamic arguments. The results are applied to sorption data to show that detailed sorption analyses are extremely useful and can provide valuable information that is difficult to obtain by any other means. Considerable emphasis has been placed on data analyses and interpretation of a nonclassical nature to show the potential of such studies that is often not recognized nor utilized

  5. Subsurface material identification and sensor selection

    Science.gov (United States)

    T, H.; Reghunadh, R.; Ramesh, M. V.

    2017-12-01

    In India, most of the landslides occur during monsoon season and causes huge loss of life and property. Design of an early warning system for highly landslide prone area will reduce losses to a great extent. The in-situ monitoring systems needs deployment of several sensors inside a borehole for monitoring a particular slope. Amrita Center for Wireless Networks and Applications (AmritaWNA), Amrita University has designed, developed and deployed a Wireless Sensor Network (WSN) for real time landslide monitoring using geotechnical instruments and sensors like rain gauge, moisture sensor, piezometer, strain gauge, tilt meter and geophone inside a Deep Earth Probe (DEP) at different locations. These sensors provide point measurements of the subsurface at a higher accuracy. Every landslide prone terrain is unique with respect to its geology, hydrological conditions, meteorological conditions, velocity of movement etc. The decision of installing different geotechnical instruments in a landslide prone terrain is a crucial step to be considered. Rain gauge, moisture sensor, and piezometer are usually used in clay rich areas to sense the moisture and pore pressure values. Geophone and Crack meter are instruments used in rocky areas to monitor cracks and vibrations associated with a movement. Inclinometer and Strain gauge are usually placed inside a casing and can be used in both rocky and soil areas. In order to place geotechnical instruments and sensors at appropriate places Electrical Resistivity Tomography (ERT) method can be used. Variation in electrical resistivity values indicate the changes in composition, layer thickness, or contaminant levels. The derived true resistivity image can be used for identifying the type of materials present in the subsurface at different depths. We have used this method for identifying the type of materials present in our site at Chandmari (Sikkim). Fig 1 shows the typical resistivity values of a particular area in Chandmari site. The

  6. Composite Materials in Aircraft Mishaps Involving Fire: A Literature Review

    National Research Council Canada - National Science Library

    Wright, Mark

    2003-01-01

    .... The Naval Air Systems Command (NAVAIR), which provides technical guidance for aircraft fire safety, was concerned that hazards presented by new composite materials and greater quantities of composites may not be adequately addressed...

  7. Transportation incidents involving Canadian shipments of radioactive material

    International Nuclear Information System (INIS)

    Jardine, J.M.

    1979-06-01

    This paper gives a brief statement of the legislation governing the transportation of radioactive materials in Canada, reviews the types of shipments made in Canada in 1977, and surveys the transportation incidents that have been reported to the Atomic Energy Control Board over the period 1947-1978. Some of the more significant incidents are described in detail. A totAl of 135 incidents occurred from 1947 to 1978, during which time there were 644750 shipments of radioactive material in Canada

  8. Material Selection for Accident Tolerant Fuel Cladding

    International Nuclear Information System (INIS)

    Pint, Bruce A.; Terrani, Kurt A.; Yamamoto, Yukinori; Snead, Lance Lewis

    2015-01-01

    Alternative cladding materials to Zr-based alloys are being investigated for accident tolerance, which can be defined as > 100X improvement (compared to Zr-based alloys) in oxidation resistance to steam or steam-H 2 environments at ≥1473 K (1200°C) for short times. After reviewing a wide range of candidates, current steam oxidation testing is being conducted on Mo, MAX phases and FeCrAl alloys. Recently reported low mass losses for Mo in steam at 800°C could not be reproduced. Both FeCrAl and MAX phase Ti 2 AlC form a protective alumina scale in steam. However, commercial Ti 2 AlC that was not single phase, formed a much thicker oxide at 1200°C in steam and significant TiO 2 , and therefore Ti 2 AlC may be challenging to form as a cladding or a coating. Alloy development for FeCrAl is seeking to maintain its steam oxidation resistance to 1475°C, while reducing its Cr content to minimize susceptibility to irradiation-assisted α' formation. The composition effects and critical limits to retaining protective scale formation at > 1400°C are still being evaluated.

  9. Material Selection for Accident Tolerant Fuel Cladding

    Energy Technology Data Exchange (ETDEWEB)

    Pint, Bruce A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Terrani, Kurt A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Yamamoto, Yukinori [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Snead, Lance Lewis [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-01-01

    Alternative cladding materials to Zr-based alloys are being investigated for accident tolerance, which can be defined as > 100X improvement (compared to Zr-based alloys) in oxidation resistance to steam or steam-H2 environments at ≥ 1200°C for short times. After reviewing a wide range of candidates, current steam oxidation testing is being conducted on Mo, MAX phases and FeCrAl alloys. Recently reported low mass losses for Mo in steam at 800°C could not be reproduced. Both FeCrAl and MAX phase Ti2AlC form a protective alumina scale in steam. However, commercial Ti2AlC that was not single phase, formed a much thicker oxide at 1200°C in steam and significant TiO2, and therefore Ti2AlC may be challenging to form as a cladding or a coating. Alloy development for FeCrAl is seeking to maintain its steam oxidation resistance to 1475°C, while reducing its Cr content to minimize susceptibility to irradiation-assisted α´ formation. The composition effects and critical limits to retaining protective scale formation at > 1400°C are still being evaluated.

  10. Selective Integration in the Material-Point Method

    DEFF Research Database (Denmark)

    Andersen, Lars; Andersen, Søren; Damkilde, Lars

    2009-01-01

    The paper deals with stress integration in the material-point method. In order to avoid parasitic shear in bending, a formulation is proposed, based on selective integration in the background grid that is used to solve the governing equations. The suggested integration scheme is compared...... to a traditional material-point-method computation in which the stresses are evaluated at the material points. The deformation of a cantilever beam is analysed, assuming elastic or elastoplastic material behaviour....

  11. Selection of materials in nuclear fuel: present and future

    International Nuclear Information System (INIS)

    Munoz-Reja, C.; Fuentes, L.; Garcia de la Infanta, J. M.; Munoz Sicilia, A.

    2013-01-01

    One of the main aspects of the nuclear fuel is the selection of materials for the components. The operating conditions of the fuel elements impose a major challenge to materials: high temperature, corrosive aqueous environment, high mechanical properties, long periods of time under these extreme conditions and what is the differentiating factor; the effect of irradiation. The materials are selected to fulfill these severe requirements and also to be able to control and to predict its behavior in the working conditions. Their development, in terms of composition and processing, is based on the continuous follow-up of the operation behavior. Many of these materials are specific of the nuclear industry, such as the uranium dioxide and the zirconium alloys. This article presents the selection and development of the nuclear fuel materials as a function of the services requirements. It also includes a view of the new nuclear fuels materials that are being raised after Fukushima accident. (Author)

  12. ICP MS selection of radiopure materials for the GERDA experiment

    Science.gov (United States)

    di Vacri, M. L.; Nisi, S.; Cattadori, C.; Janicsko, J.; Lubashevskiy, A.; Smolnikov, A.; Walter, M.

    2015-08-01

    The GERDA (GERmanium Detector Array) experiment, located in the Gran Sasso Underground Laboratory (LNGS, Italy) aims to search for neutrinoless double beta (0νββ) decay of the 76Ge isotope. Both an ultra-low radioactivity background environment and active techniques to abate the residual background are required to reach the background index (of 10-3 counts/keV kg y) at the Qββ. In order to veto and suppress those events that partially deposit energy in Ge detectors, the readout of liquid argon (LAr) scintillation light (SL) has been implemented for the second GERDA experimental Phase. A double veto system has been designed and constructed using highly radiopure materials (scintillating fibers, wavelength shifters, polymeric foils, reflective foils). This work describes the study of lead, thorium and uranium ultra-trace content, performed at the LNGS Chemistry Laboratory by High Resolution Mass Spectrometry (HR ICP MS), for the selection of all materials involved in the construction of the veto system

  13. ICP MS selection of radiopure materials for the GERDA experiment

    Energy Technology Data Exchange (ETDEWEB)

    Di Vacri, M. L., E-mail: divacrim@lngs.infn.it [INFN, Laboratori Nazionali del Gran Sasso, via G.Acitelli 22, 67100 Assergi (Italy); Dipartimento di Scienze Fisiche e Chimiche, University of L’Aquila, via Vetoio, 67100 L’Aquila (Italy); Nisi, S., E-mail: nisi@lngs.infn.it [INFN, Laboratori Nazionali del Gran Sasso, via G.Acitelli 22, 67100 Assergi (AQ) (Italy); Cattadori, C., E-mail: cattadori@lngs.infn.it [INFN Sezione di Milano Bicocca, Milano (Italy); Janicsko, J. [TUM Munich (Germany); Lubashevskiy, A. [MPIK, Heidelberg (Germany); JINR, Dubna (Russian Federation); Smolnikov, A. [MPIK, Heidelberg (Germany); Walter, M. [Physik-Institut, Universitat Zurich, 8057 Zurich (Switzerland)

    2015-08-17

    The GERDA (GERmanium Detector Array) experiment, located in the Gran Sasso Underground Laboratory (LNGS, Italy) aims to search for neutrinoless double beta (0νββ) decay of the {sup 76}Ge isotope. Both an ultra-low radioactivity background environment and active techniques to abate the residual background are required to reach the background index (of 10{sup −3} counts/keV kg y) at the Q{sub ββ}. In order to veto and suppress those events that partially deposit energy in Ge detectors, the readout of liquid argon (LAr) scintillation light (SL) has been implemented for the second GERDA experimental Phase. A double veto system has been designed and constructed using highly radiopure materials (scintillating fibers, wavelength shifters, polymeric foils, reflective foils). This work describes the study of lead, thorium and uranium ultra-trace content, performed at the LNGS Chemistry Laboratory by High Resolution Mass Spectrometry (HR ICP MS), for the selection of all materials involved in the construction of the veto system.

  14. Transportation accidents/incidents involving radioactive materials (1971-1991)

    International Nuclear Information System (INIS)

    Cashwell, C.E.; McClure, J.D.

    1993-01-01

    In 1981, Sandia National Laboratories developed the Radioactive Materials Incident Report (RMIR) database to support its research and development activities for the U.S. Department of Energy (DOE). The RMIR database contains information on transportation accidents/incidents with radioactive materials that have occurred since 1971. The RMIR classifies a transportation accident/incident in one of six ways: as a transportation accident, a handling accident, a reported incident, missing or stolen, cask weeping, or other. This paper will define these terms and provide detailed examples of each. (J.P.N.)

  15. Selective involvement of the amygdala in systemic lupus erythematosus.

    Directory of Open Access Journals (Sweden)

    Bart J Emmer

    2006-12-01

    Full Text Available BACKGROUND: Antibodies specifically affect the amygdala in a mouse model of systemic lupus erythematosus (SLE. The aim of our study was to investigate whether there is also specific involvement of the amygdala in human SLE. METHODS AND FINDINGS: We analyzed a group of 37 patients with neuropsychiatric SLE (NP-SLE, 21 patients with SLE, and a group of 12 healthy control participants with diffusion weighted imaging (DWI. In addition, in a subset of eight patients, plasma was available to determine their anti-NMDAR antibody status. From the structural magnetic resonance imaging data, the amygdala and the hippocampus were segmented, as well as the white and gray matter, and the apparent diffusion coefficient (ADC was retrieved. ADC values between controls, patients with SLE, and patients with NP-SLE were tested using analysis of variance with post-hoc Bonferroni correction. No differences were found in the gray or white matter segments. The average ADC in the amygdala of patients with NP-SLE and SLE (940 x 10(-6 mm2/s; p = 0.006 and 949 x 10(-6 mm2/s; p = 0.019, respectively was lower than in healthy control participants (1152 x 10(-6 mm2/s. Mann-Whitney analysis revealed that the average ADC in the amygdala of patients with anti-NMDAR antibodies (n = 4; 802 x 10(-6 mm2/s was lower (p = 0.029 than the average ADC of patients without anti-NMDAR antibodies (n = 4; 979 x 10(-6 mm2/s and also lower (p = 0.001 than in healthy control participants. CONCLUSIONS: This is the first study to our knowledge to observe damage in the amygdala in patients with SLE. Patients with SLE with anti-NMDAR antibodies had more severe damage in the amygdala compared to SLE patients without anti-NMDAR antibodies.

  16. Photovoltaic module encapsulation design and materials selection, volume 1

    Science.gov (United States)

    Cuddihy, E.; Carroll, W.; Coulbert, C.; Gupta, A.; Liang, R. H.

    1982-01-01

    Encapsulation material system requirements, material selection criteria, and the status and properties of encapsulation materials and processes available are presented. Technical and economic goals established for photovoltaic modules and encapsulation systems and their status are described. Available encapsulation technology and data are presented to facilitate design and material selection for silicon flat plate photovoltaic modules, using the best materials available and processes optimized for specific power applications and geographic sites. The operational and environmental loads that encapsulation system functional requirements and candidate design concepts and materials that are identified to have the best potential to meet the cost and performance goals for the flat plate solar array project are described. Available data on encapsulant material properties, fabrication processing, and module life and durability characteristics are presented.

  17. Assessment of Heat Hazard during the Polymerization of Selected Light-Sensitive Dental Materials

    OpenAIRE

    Janeczek, Maciej; Herman, Katarzyna; Fita, Katarzyna; Dudek, Krzysztof; Kowalczyk-Zaj?c, Ma?gorzata; Czajczy?ska-Waszkiewicz, Agnieszka; Piesiak-Pa?czyszyn, Dagmara; Kosior, Piotr; Dobrzy?ski, Maciej

    2016-01-01

    Introduction. Polymerization of light-cured dental materials used for restoration of hard tooth tissue may lead to an increase in temperature that may have negative consequence for pulp vitality. Aim. The aim of this study was to determine maximum temperatures reached during the polymerization of selected dental materials, as well as the time that is needed for samples of sizes similar to those used in clinical practice to reach these temperatures. Materials and Methods. The study involved fo...

  18. Fires involving radioactive materials : transference model; operative recommendations

    International Nuclear Information System (INIS)

    Rodriguez, C.E.; Puntarulo, L.J.; Canibano, J.A.

    1988-01-01

    In all aspects related to the nuclear activity, the occurrence of an explosion, fire or burst type accident, with or without victims, is directly related to the characteristics of the site. The present work analyses the different parameters involved, describing a transference model and recommendations for evaluation and control of the radiological risk for firemen. Special emphasis is placed on the measurement of the variables existing in this kind of operations

  19. The Selection of Materials for Roller Chains From The Perspective Of Manufacturing Process

    Directory of Open Access Journals (Sweden)

    Rahmat Saptono

    2010-10-01

    Full Text Available The selection of materials for an engineering component is not only requested by its design function and shape, but also the sequence through which it is manufactured. The manufacturing operation of roller chains involves drawing and trimming processes aimed at producing semi-finished chain drives component with a well-standardized dimension. In addition to final combination of properties required by design constraints, the ability of materials to be formed into a desired shape and geometry without failure is also critical. The objective of materials selection should therefore involve additional attributes that are not typically  accommodated by the standard procedure of materials selection. The present paper deals with the selection of materials for roller chains from the perspective of manufacturing process. Ears and un-uniform wall thickness have been identified as a key problem in the mass production of component. Provided all process parameters were established, the  anisotropy factor of materials is critical. Simulative test can be reasonably used to obtain material performance indices that can be added up to the standard procedure of material selection. Of three commercially available steel grades evaluated with regard to the criteria defined, one grade is more suitable for the present objective.

  20. Selection of views to materialize using simulated annealing algorithms

    Science.gov (United States)

    Zhou, Lijuan; Liu, Chi; Wang, Hongfeng; Liu, Daixin

    2002-03-01

    A data warehouse contains lots of materialized views over the data provided by the distributed heterogeneous databases for the purpose of efficiently implementing decision-support or OLAP queries. It is important to select the right view to materialize that answer a given set of queries. The goal is the minimization of the combination of the query evaluation and view maintenance costs. In this paper, we have addressed and designed algorithms for selecting a set of views to be materialized so that the sum of processing a set of queries and maintaining the materialized views is minimized. We develop an approach using simulated annealing algorithms to solve it. First, we explore simulated annealing algorithms to optimize the selection of materialized views. Then we use experiments to demonstrate our approach. The results show that our algorithm works better. We implemented our algorithms and a performance study of the algorithms shows that the proposed algorithm gives an optimal solution.

  1. ABOUT INDEX EVALUATION OF MATERIAL RESOURCE SUPPLIER SELECTION

    Directory of Open Access Journals (Sweden)

    V. A. Skochinskaya

    2008-01-01

    Full Text Available The paper analyzes existing methods for evaluation of material resource supplier selection. It shows advantages and shortcomings of the present evaluation systems. The necessity for application of an index evaluation is justified in the paper. The paper contains rating (index evaluation for material resource supplier selection which is based on the application of quantitative (index tool instead of an expert (numerical evaluation. 

  2. Investigating accidents involving aircraft manufactured from polymer composite materials

    OpenAIRE

    Dunn, Leigh

    2013-01-01

    This thesis looks into the examination of polymer composite wreckage from the perspective of the aircraft accident investigator. It develops an understanding of the process of wreckage examination as well as identifying the potential for visual and macroscopic interpretation of polymer composite aircraft wreckage. The in-field examination of aircraft wreckage, and subsequent interpretations of material failures, can be a significant part of an aircraft accident investigation. ...

  3. Probable Cause for Maritime Interdictions Involving Illicit Radioactive Materials

    Science.gov (United States)

    2008-12-01

    as a load of bananas ,21 the portable monitors need to have not only the ability to detect radiation but also to identify specific sources. Thus...unauthorized acts and physical storage, in order to uncover propensity to mask SNMs. Last, naturally occurring radioactive material (NORM) such as potassium ...40 (40K), which is largely used in agriculture as a fertilizer91 and exists abundantly in a great variety of natural substances, such as bananas , or

  4. Impact of schoolchildren's involvement in the design process on the effectiveness of healthy food promotion materials

    Directory of Open Access Journals (Sweden)

    Christopher R. Gustafson

    2017-06-01

    Relative to baseline, students in group 4 doubled their vegetable consumption (p < 0.001 when materials were posted. Vegetable consumption remained elevated at a follow-up 2–3 months later (p < 0.05. Students in group 3 initially increased the quantity of vegetables selected (p < 0.05, but did not increase consumption. In the follow-up period, however, students in group 3 increased their vegetable consumption (p < 0.01. Involving elementary-aged students in the design of vegetable promotional materials that were posted in the lunchroom increased the amount of vegetables students consumed.

  5. Selective Postevent Review and Children's Memory for Nonreviewed Materials

    Science.gov (United States)

    Conroy, R.; Salmon, K.

    2005-01-01

    Two experiments investigated the impact of selective postevent questioning on children's memory for nonreviewed materials. In both experiments, children participated in a series of novel activities. Children in the selective-review condition were subsequently questioned about half of these and comparisons were made to memory in a no-review…

  6. Investigating accidents involving aircraft manufactured from polymer composite materials

    Science.gov (United States)

    Dunn, Leigh

    This study looks into the examination of polymer composite wreckage from the perspective of the aircraft accident investigator. It develops an understanding of the process of wreckage examination as well as identifying the potential for visual and macroscopic interpretation of polymer composite aircraft wreckage. The in-field examination of aircraft wreckage, and subsequent interpretations of material failures, can be a significant part of an aircraft accident investigation. As the use of composite materials in aircraft construction increases, the understanding of how macroscopic failure characteristics of composite materials may aid the field investigator is becoming of increasing importance.. The first phase of this research project was to explore how investigation practitioners conduct wreckage examinations. Four accident investigation case studies were examined. The analysis of the case studies provided a framework of the wreckage examination process. Subsequently, a literature survey was conducted to establish the current level of knowledge on the visual and macroscopic interpretation of polymer composite failures. Relevant literature was identified and a compendium of visual and macroscopic characteristics was created. Two full-scale polymer composite wing structures were loaded statically, in an upward bending direction, until each wing structure fractured and separated. The wing structures were subsequently examined for the existence of failure characteristics. The examination revealed that whilst characteristics were present, the fragmentation of the structure destroyed valuable evidence. A hypothetical accident scenario utilising the fractured wing structures was developed, which UK government accident investigators subsequently investigated. This provided refinement to the investigative framework and suggested further guidance on the interpretation of polymer composite failures by accident investigators..

  7. Considerations in selecting tubing materials for CANDU steam generators

    International Nuclear Information System (INIS)

    Hemmings, R.L.

    1978-01-01

    Corrosion resistance is the major consideration in selecting tubing material for CANDU steam generators. Corrosion, and additional considerations, lead to the following steam generator tubing material recommendations: for CANDU-BPHWR's (boiling pressurized heavy water reactors) low-cobalt Incoloy-800; for CANDU-PHWR's (pressurized, non-boiling, heavy water reactors), low-cobalt Monel-400

  8. Impact of schoolchildren's involvement in the design process on the effectiveness of healthy food promotion materials.

    Science.gov (United States)

    Gustafson, Christopher R; Abbey, Bryce M; Heelan, Kate A

    2017-06-01

    Marketing techniques may improve children's vegetable consumption. However, student participation in the design of marketing materials may increase the material's salience, while also improving children's commitment and attitudes towards healthy eating. The impact of student-led design of vegetable promotional materials on choice and consumption was investigated using 1614 observations of students' vegetable choice and plate waste in four public elementary schools in Kearney, Nebraska. Data were collected on children's vegetable choice and consumption in four comparison groups: 1) control; 2) students designed materials only; 3) students were exposed to promotional materials only; and 4) students designed materials that were then posted in the lunchroom. Vegetable choice and consumption data were collected through a validated digital photography-based plate-waste method. Multivariate linear regression was used to estimate average treatment effects of the conditions at various time periods. Dependent variables were vegetable choice and consumption, and independent variables included the condition, time period, and interaction terms, as well as controls for gender and grade. Relative to baseline, students in group 4 doubled their vegetable consumption ( p  < 0.001) when materials were posted. Vegetable consumption remained elevated at a follow-up 2-3 months later ( p  < 0.05). Students in group 3 initially increased the quantity of vegetables selected ( p  < 0.05), but did not increase consumption. In the follow-up period, however, students in group 3 increased their vegetable consumption ( p  < 0.01). Involving elementary-aged students in the design of vegetable promotional materials that were posted in the lunchroom increased the amount of vegetables students consumed.

  9. Basic Thermal Parameters of Selected Foods and Food Raw Materials

    Directory of Open Access Journals (Sweden)

    Monika Božiková

    2017-01-01

    Full Text Available In general, processing and manipulation with foods and food raw materials have significant influence on their physical properties. The article is focused on thermophysical parameters measurement of selected foods and food raw materials. There were examined thermal conductivity and thermal diffusivity of selected materials. For detection of thermal parameters was used instrument Isomet 2104, which principle of measurement is based on transient methods. In text are presented summary results of thermal parameters measurement for various foods and food raw materials as: granular materials – corn flour and wheat flour; fruits, vegetables and fruit products – grated apple, dried apple and apple juice; liquid materials – milk, beer etc. Measurements were performed in two temperature ranges according to the character of examined material. From graphical relations of thermophysical parameter is evident, that thermal conductivity and diffusivity increases with temperature and moisture content linearly, only for granular materials were obtained non‑linear dependencies. Results shows, that foods and food raw materials have different thermal properties, which are influenced by their type, structure, chemical and physical properties. From presented results is evident, that basic thermal parameters are important for material quality detection in food industry.

  10. Properties of selected superconductive materials, 1978 supplement. Technical note

    International Nuclear Information System (INIS)

    Roberts, B.W.

    1978-10-01

    This report includes data on additional superconductive materials extracted from the world literature up to fall 1977 and is an addendum to the data set published in J. Phys. Chem. Ref. Data 5, no. 3, 581-821 (1976) (Reprint no. 84). The data presented are new values and have not been selected or compared to values (except for selected values of the elements) previously assembled by the Superconductive Materials Data Center. The properties included are composition, critical temperature, critical magnetic field, crystal structure and the results of negative experiments. Special tabulations of high magnetic field materials with Type II behavior and materials with organic components are included. All entries are keyed to the literature. A list of recent reviews centered on superconductive materials is included

  11. Selective laser sintering of calcium phosphate materials for orthopedic implants

    Science.gov (United States)

    Lee, Goonhee

    Two technologies, Solid Freeform Fabrication (SFF) and bioceramics are combined in this work to prepare bone replacement implants with complex geometry. SFF has emerged as a crucial technique for rapid prototyping in the last decade. Selective Laser Sintering (SLS) is one of the established SFF manufacturing processes that can build three-dimensional objects directly from computer models without part-specific tooling or human intervention. Meanwhile, there have been great efforts to develop implantable materials that can assist in regeneration of bone defects and injuries. However, little attention has been focused in shaping bones from these materials. The main thrust of this research was to develop a process that can combine those two separate efforts. The specific objective of this research is to develop a process that can construct bone replacement material of complex geometry from synthetic calcium phosphate materials by using the SLS process. The achievement of this goal can have a significant impact on the quality of health care in the sense that complete custom-fit bone and tooth structures suitable for implantation can be prepared within 24--48 hours of receipt of geometric information obtained either from patient Computed Tomographic (CT) data, from Computer Aided Design (CAD) software or from other imaging systems such as Magnetic Resonance Imaging (MRI) and Holographic Laser Range Imaging (HLRI). In this research, two different processes have been developed. First is the SLS fabrication of porous bone implants. In this effort, systematic procedures have been established and calcium phosphate implants were successfully fabricated from various sources of geometric information. These efforts include material selection and preparation, SLS process parameter optimization, and development of post-processing techniques within the 48-hour time frame. Post-processing allows accurate control of geometry and of the chemistry of calcium phosphate, as well as

  12. An annotated history of container candidate material selection

    International Nuclear Information System (INIS)

    McCright, R.D.

    1988-07-01

    This paper documents events in the Nevada Nuclear Waste Storage Investigations (NNWSI) Project that have influenced the selection of metals and alloys proposed for fabrication of waste package containers for permanent disposal of high-level nuclear waste in a repository at Yucca Mountain, Nevada. The time period from 1981 to 1988 is covered in this annotated history. The history traces the candidate materials that have been considered at different stages of site characterization planning activities. At present, six candidate materials are considered and described in the 1988 Consultation Draft of the NNWSI Site Characterization Plan (SCP). The six materials are grouped into two alloy families, copper-base materials and iron to nickel-base materials with an austenitic structure. The three austenitic candidates resulted from a 1983 survey of a longer list of candidate materials; the other three candidates resulted from a special request from DOE in 1984 to evaluate copper and copper-base alloys. 24 refs., 2 tabs

  13. A fuzzy logic based PROMETHEE method for material selection problems

    Directory of Open Access Journals (Sweden)

    Muhammet Gul

    2018-03-01

    Full Text Available Material selection is a complex problem in the design and development of products for diverse engineering applications. This paper presents a fuzzy PROMETHEE (Preference Ranking Organization Method for Enrichment Evaluation method based on trapezoidal fuzzy interval numbers that can be applied to the selection of materials for an automotive instrument panel. Also, it presents uniqueness in making a significant contribution to the literature in terms of the application of fuzzy decision-making approach to material selection problems. The method is illustrated, validated, and compared against three different fuzzy MCDM methods (fuzzy VIKOR, fuzzy TOPSIS, and fuzzy ELECTRE in terms of its ranking performance. Also, the relationships between the compared methods and the proposed scenarios for fuzzy PROMETHEE are evaluated via the Spearman’s correlation coefficient. Styrene Maleic Anhydride and Polypropylene are determined optionally as suitable materials for the automotive instrument panel case. We propose a generic fuzzy MCDM methodology that can be practically implemented to material selection problem. The main advantages of the methodology are consideration of the vagueness, uncertainty, and fuzziness to decision making environment.

  14. Selection of material balance areas and item control areas

    International Nuclear Information System (INIS)

    1975-04-01

    Section 70.58, ''Fundamental Nuclear Material Controls,'' of 10 CFR Part 70, ''Special Nuclear Material,'' requires certain licensees authorized to possess more than one effective kilogram of special nuclear material to establish Material Balance Areas (MBAs) or Item Control Areas (ICAs) for the physical and administrative control of nuclear materials. This section requires that: (1) each MBA be an identifiable physical area such that the quantity of nuclear material being moved into or out of the MBA is represented by a measured value; (2) the number of MBAs be sufficient to localize nuclear material losses or thefts and identify the mechanisms; (3) the custody of all nuclear material within an MBA or ICA be the responsibility of a single designated individual; and (4) ICAs be established according to the same criteria as MBAs except that control into and out of such areas would be by item identity and count for previously determined special nuclear material quantities, the validity of which must be ensured by tamper-safing unless the items are sealed sources. This guide describes bases acceptable to the NRC staff for the selection of material balance areas and item control areas. (U.S.)

  15. New ion selective materials. Application to the selective extraction of caesium

    International Nuclear Information System (INIS)

    Favre-Reguillon, Alain

    1996-01-01

    This research thesis addresses the synthesis and assessment of ion selective materials. The first part reports the development of a general method of assessment of ion selective materials. In the second part, the author describes different methods used to insolubilize macro-cycles on hydrophilic polymers. The obtained polyurethanes are synthesised. These hydrophilic polymers display interesting complexing properties and selectivities with respect to cations of alkali metals. Then the author addresses the improvement of selectivity with respect to caesium of ion exchange resorcinol-formaldehyde resins. Different factors affecting selectivity are identified, and the concept of molecular print is used to study the improvement of selectivity. The effect of macro-cyclic structures on phenolic resins with respect to caesium is highlighted [fr

  16. Quality indexes for selecting control materials of the nuclear reactors

    International Nuclear Information System (INIS)

    Martinez-Val, J.M.; Pena, J.; Esteban Naudin, A.

    1981-01-01

    Quality indexes are established and valued for selecting control materials, The requirements for accomplishing such purposes are explained with detailed analysis: absortion cross section must be as high as possible, adequate reactivity evolution versus depletion, good resistance to radiation, appropiate thermal stability, mechanical resistance and ductility, chemical compatibility with the environment, good heat transfer properties, abundant in the nature and low costs. At present Westinghouse desire to commercialize hafnium as control material shows the exciting task of looking for new materials controlling nuclear reactors. (auth.)

  17. Corrosion behaviour of materials selected for FMIT lithium system

    Energy Technology Data Exchange (ETDEWEB)

    Bazinet, G.D.; Brehm, W.F.

    1983-09-01

    The corrosion behavior of selected materials in a liquid lithium environment was studied in support of system and component designs for the Fusion Materials Irradiation Test (FMIT) Facility. Testing conditions ranged from about 3700 to about6500 hours of exposure to flowing lithium at temperatures from 230/sup 0/ to 270/sup 0/C and static lithium at temperatures from 200/sup 0/ to 500/sup 0/C. Principal areas of investigation included lithium corrosion/erosion effects on FMIT lithium system baseline and candidate materials. Material coupons and full-size prototypic components were evaluated to determine corrosion rates, fatigue crack growth rates, structural compatibility, and component acceptability for the lithium system. Based on the results of these studies, concerns regarding system materials and component designs were satisfactorily resolved to support a 20-year design life requirement for the FMIT lithium system.

  18. Corrosion behaviour of materials selected for FMIT lithium system

    International Nuclear Information System (INIS)

    Bazinet, G.D.; Brehm, W.F.

    1983-01-01

    The corrosion behavior of selected materials in a liquid lithium environment was studied in support of system and component designs for the Fusion Materials Irradiation Test (FMIT) Facility. Testing conditions ranged from about 3700 to about6500 hours of exposure to flowing lithium at temperatures from 230 0 to 270 0 C and static lithium at temperatures from 200 0 to 500 0 C. Principal areas of investigation included lithium corrosion/erosion effects on FMIT lithium system baseline and candidate materials. Material coupons and full-size prototypic components were evaluated to determine corrosion rates, fatigue crack growth rates, structural compatibility, and component acceptability for the lithium system. Based on the results of these studies, concerns regarding system materials and component designs were satisfactorily resolved to support a 20-year design life requirement for the FMIT lithium system

  19. Selected Audio-Visual Materials for Consumer Education. [New Version.

    Science.gov (United States)

    Johnston, William L.

    Ninety-two films, filmstrips, multi-media kits, slides, and audio cassettes, produced between 1964 and 1974, are listed in this selective annotated bibliography on consumer education. The major portion of the bibliography is devoted to films and filmstrips. The main topics of the audio-visual materials include purchasing, advertising, money…

  20. Materials selection for a transport packaging of Mo-99

    International Nuclear Information System (INIS)

    Hara, Debora H.S.; Lucchesi, Raquel F.; Mancini, Victor A.; Rossi, Jesualdo L.; Fiore, Marina

    2015-01-01

    The radiopharmaceuticals are radioactive isotopes used in nuclear medicine for more accurate diagnosis and treatment of diseases or dysfunctions. Currently, the most important radionuclide for the preparation of radiopharmaceuticals for diagnostic purposes is technetium-99m ( 99m Tc), a product of the radioactive decay of molybdenum-99 (Mo-99). The aim of this work was the materials selection that can enable the manufacture of a package for Mo-99 transport with the aid of CES EduPack program and the methodology developed by Ashby. The ESTAR program was used to check the occurrence of Bremsstrahlung and the XCOM program was used to calculate the attenuation coefficient of gamma radiation from some of the selected materials for the shield; after, the thickness required for radiation shielding was calculated. From the results, the materials selected as potential candidates for the manufacture of the shielding were the tungsten alloys. Related to the thermal insulation and the impact protection, woods, plywoods and particle boards stand out. With regard to internal and external coatings, the selected materials focus on groups of steels and nickel alloys. (author)

  1. An integrated approach towards future ballistic neck protection materials selection.

    Science.gov (United States)

    Breeze, John; Helliker, Mark; Carr, Debra J

    2013-05-01

    Ballistic protection for the neck has historically taken the form of collars attached to the ballistic vest (removable or fixed), but other approaches, including the development of prototypes incorporating ballistic material into the collar of an under body armour shirt, are now being investigated. Current neck collars incorporate the same ballistic protective fabrics as the soft armour of the remaining vest, reflecting how ballistic protective performance alone has historically been perceived as the most important property for neck protection. However, the neck has fundamental differences from the thorax in terms of anatomical vulnerability, flexibility and equipment integration, necessitating a separate solution from the thorax in terms of optimal materials selection. An integrated approach towards the selection of the most appropriate combination of materials to be used for each of the two potential designs of future neck protection has been developed. This approach requires evaluation of the properties of each potential material in addition to ballistic performance alone, including flexibility, mass, wear resistance and thermal burden. The aim of this article is to provide readers with an overview of this integrated approach towards ballistic materials selection and an update of its current progress in the development of future ballistic neck protection.

  2. Supercritical boiler material selection using fuzzy analytic network process

    Directory of Open Access Journals (Sweden)

    Saikat Ranjan Maity

    2012-08-01

    Full Text Available The recent development of world is being adversely affected by the scarcity of power and energy. To survive in the next generation, it is thus necessary to explore the non-conventional energy sources and efficiently consume the available sources. For efficient exploitation of the existing energy sources, a great scope lies in the use of Rankin cycle-based thermal power plants. Today, the gross efficiency of Rankin cycle-based thermal power plants is less than 28% which has been increased up to 40% with reheating and regenerative cycles. But, it can be further improved up to 47% by using supercritical power plant technology. Supercritical power plants use supercritical boilers which are able to withstand a very high temperature (650-720˚C and pressure (22.1 MPa while producing superheated steam. The thermal efficiency of a supercritical boiler greatly depends on the material of its different components. The supercritical boiler material should possess high creep rupture strength, high thermal conductivity, low thermal expansion, high specific heat and very high temperature withstandability. This paper considers a list of seven supercritical boiler materials whose performance is evaluated based on seven pivotal criteria. Given the intricacy and difficulty of this supercritical boiler material selection problem having interactions and interdependencies between different criteria, this paper applies fuzzy analytic network process to select the most appropriate material for a supercritical boiler. Rene 41 is the best supercritical boiler material, whereas, Haynes 230 is the worst preferred choice.

  3. Patterns of Parental Involvement in Selected OECD Countries: Cross-National Analyses of PISA

    Science.gov (United States)

    Hartas, Dimitra

    2015-01-01

    Using data from the Programme for International Student Assessment (PISA), patterns of parental involvement were examined in selected OECD countries. The findings showed that, irrespective of educational qualifications, parents were frequently involved in their children's learning at the start of primary school and at age 15. Cross-national…

  4. Materials selection guidelines for geothermal energy utilization systems

    Energy Technology Data Exchange (ETDEWEB)

    Ellis, P.F. II; Conover, M.F.

    1981-01-01

    This manual includes geothermal fluid chemistry, corrosion test data, and materials operating experience. Systems using geothermal energy in El Salvador, Iceland, Italy, Japan, Mexico, New Zealand, and the United States are described. The manual provides materials selection guidelines for surface equipment of future geothermal energy systems. The key chemical species that are significant in determining corrosiveness of geothermal fluids are identified. The utilization modes of geothermal energy are defined as well as the various physical fluid parameters that affect corrosiveness. Both detailed and summarized results of materials performance tests and applicable operating experiences from forty sites throughout the world are presented. The application of various non-metal materials in geothermal environments are discussed. Included in appendices are: corrosion behavior of specific alloy classes in geothermal fluids, corrosion in seawater desalination plants, worldwide geothermal power production, DOE-sponsored utilization projects, plant availability, relative costs of alloys, and composition of alloys. (MHR)

  5. Material selection for Multi-Function Waste Tank Facility tanks

    International Nuclear Information System (INIS)

    Carlos, W.C.

    1994-01-01

    This report briefly summarizes the history of the materials selection for the US Department of Energy's high-level waste carbon steel storage tanks. It also provide an evaluation of the materials for the construction of new tanks at the Multi-Function Waste Tank Facility. The evaluation included a materials matrix that summarized the critical design, fabrication, construction, and corrosion resistance requirements; assessed each requirement; and cataloged the advantages and disadvantages of each material. This evaluation is based on the mission of the Multi-Function Waste Tank Facility. On the basis of the compositions of the wastes stored in Hanford waste tanks, it is recommended that tanks for the Multi-Function Waste Tank Facility be constructed of normalized ASME SA 516, Grade 70, carbon steel

  6. Review of selective laser melting: Materials and applications

    Energy Technology Data Exchange (ETDEWEB)

    Yap, C. Y., E-mail: cyap001@e.ntu.edu.sg [Singapore Centre for 3D Printing, School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, Block N3.1 - B2c - 01, Singapore 639798 (Singapore); Energy Research Institute @ NTU, Interdisciplinary Graduate School, Nanyang Technological University, 50 Nanyang Avenue, Block S2 - B3a - 01, Singapore 639798 (Singapore); Chua, C. K., E-mail: mckchua@ntu.edu.sg; Liu, Z. H., E-mail: azhliu@ntu.edu.sg; Zhang, D. Q., E-mail: zhangdq@ntu.edu.sg; Loh, L. E., E-mail: leloh1@e.ntu.edu.sg; Sing, S. L., E-mail: sing0011@e.ntu.edu.sg [Singapore Centre for 3D Printing, School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, Block N3.1 - B2c - 01, Singapore 639798 (Singapore); Dong, Z. L., E-mail: zldong@ntu.edu.sg [School of Materials Science & Engineering, Nanyang Technological University, 50 Nanyang Avenue, Block N4.1, Singapore 639798 (Singapore)

    2015-12-15

    Selective Laser Melting (SLM) is a particular rapid prototyping, 3D printing, or Additive Manufacturing (AM) technique designed to use high power-density laser to melt and fuse metallic powders. A component is built by selectively melting and fusing powders within and between layers. The SLM technique is also commonly known as direct selective laser sintering, LaserCusing, and direct metal laser sintering, and this technique has been proven to produce near net-shape parts up to 99.9% relative density. This enables the process to build near full density functional parts and has viable economic benefits. Recent developments of fibre optics and high-power laser have also enabled SLM to process different metallic materials, such as copper, aluminium, and tungsten. Similarly, this has also opened up research opportunities in SLM of ceramic and composite materials. The review presents the SLM process and some of the common physical phenomena associated with this AM technology. It then focuses on the following areas: (a) applications of SLM materials and (b) mechanical properties of SLM parts achieved in research publications. The review is not meant to put a ceiling on the capabilities of the SLM process but to enable readers to have an overview on the material properties achieved by the SLM process so far. Trends in research of SLM are also elaborated in the last section.

  7. Review of selective laser melting: Materials and applications

    Science.gov (United States)

    Yap, C. Y.; Chua, C. K.; Dong, Z. L.; Liu, Z. H.; Zhang, D. Q.; Loh, L. E.; Sing, S. L.

    2015-12-01

    Selective Laser Melting (SLM) is a particular rapid prototyping, 3D printing, or Additive Manufacturing (AM) technique designed to use high power-density laser to melt and fuse metallic powders. A component is built by selectively melting and fusing powders within and between layers. The SLM technique is also commonly known as direct selective laser sintering, LaserCusing, and direct metal laser sintering, and this technique has been proven to produce near net-shape parts up to 99.9% relative density. This enables the process to build near full density functional parts and has viable economic benefits. Recent developments of fibre optics and high-power laser have also enabled SLM to process different metallic materials, such as copper, aluminium, and tungsten. Similarly, this has also opened up research opportunities in SLM of ceramic and composite materials. The review presents the SLM process and some of the common physical phenomena associated with this AM technology. It then focuses on the following areas: (a) applications of SLM materials and (b) mechanical properties of SLM parts achieved in research publications. The review is not meant to put a ceiling on the capabilities of the SLM process but to enable readers to have an overview on the material properties achieved by the SLM process so far. Trends in research of SLM are also elaborated in the last section.

  8. Review of selective laser melting: Materials and applications

    International Nuclear Information System (INIS)

    Yap, C. Y.; Chua, C. K.; Liu, Z. H.; Zhang, D. Q.; Loh, L. E.; Sing, S. L.; Dong, Z. L.

    2015-01-01

    Selective Laser Melting (SLM) is a particular rapid prototyping, 3D printing, or Additive Manufacturing (AM) technique designed to use high power-density laser to melt and fuse metallic powders. A component is built by selectively melting and fusing powders within and between layers. The SLM technique is also commonly known as direct selective laser sintering, LaserCusing, and direct metal laser sintering, and this technique has been proven to produce near net-shape parts up to 99.9% relative density. This enables the process to build near full density functional parts and has viable economic benefits. Recent developments of fibre optics and high-power laser have also enabled SLM to process different metallic materials, such as copper, aluminium, and tungsten. Similarly, this has also opened up research opportunities in SLM of ceramic and composite materials. The review presents the SLM process and some of the common physical phenomena associated with this AM technology. It then focuses on the following areas: (a) applications of SLM materials and (b) mechanical properties of SLM parts achieved in research publications. The review is not meant to put a ceiling on the capabilities of the SLM process but to enable readers to have an overview on the material properties achieved by the SLM process so far. Trends in research of SLM are also elaborated in the last section

  9. Durability of Selected Membrane Materials when Exposed to Chlorine Gas

    Energy Technology Data Exchange (ETDEWEB)

    Eikeland, Marianne Soerflaten

    2001-03-01

    This thesis is focusing on the durability of selected membrane materials when exposed to chlorine gas in the temperature range 30-100{sup o}C. Studies of the changes of membrane separation properties and the mechanisms promoting these changes have been studied. The selected membrane materials were poly(dimethylsioxane) (PDMS), Fluorel, fluorosilicone, and blends of PDMS and Fluorel. The thesis is organised in seven chapters. The first chapter gives an introduction to the background of the work. The second chapter presents the theory for gas separation using dense rubbery membranes. The properties of the selected membrane materials are presented in chapter three. The fourth chapter describes degradation mechanisms for polymeric materials in general and for the selected membrane materials in particular. Presentation of the experimental work is given in chapter five, while the results with discussions are presented in chapter six. The conclusions and recommendations for further studies are given in chapter seven. Five appendixes are attached: Appendix A describes the calculations of permeability and solubility coefficients and the accuracy of the experimental measurements. Appendix B summarises the measured values in tables and Appendix C describes the analytical methods. Appendix D gives the properties of the gases used in the experiments. Appendix E is the article ''Durability of Poly(dimethylsiloxane) when Exposed to Chlorine Gas'', submitted to the Journal of Applied Polymer Science. Highly crosslinked PDMS was found to have an initial high permeability for chlorine gas and a high Cl{sub 2}/O{sub 2} selectivity. However when exposed to chlorine gas the permeability decreased significantly. Crosslinking of the PDMS polymer chain and chlorination of the polymer gave a denser polymer structure and thus lower permeability. Fluorel showed very low permeabilities and selectivities for the gases in question and was thus not interesting for this

  10. Merit exponents and control area diagrams in materials selection

    International Nuclear Information System (INIS)

    Zander, Johan; Sandstroem, Rolf

    2011-01-01

    Highlights: → Merit exponents are introduced to generalise the merit indices commonly used in materials selection. → The merit exponents can rank materials in general design situations. → To allow identification of the active merit exponent(s), control area diagrams are used. → Principles for generating the control area diagrams are presented. -- Abstract: Merit indices play a fundamental role in materials selection, since they enable ranking of materials. However, the conventional formulation of merit indices is associated with severe limitations. They are dependent on the explicit solution of the variables in the equations for the constraints from the design criteria. Furthermore, it is not always easy to determine which the controlling merit index is. To enable the ranking of materials in more general design cases, merit exponents are introduced as generalisations of the merit indices. Procedures are presented for how to compute the merit exponents numerically without having to solve equations algebraically. Merit exponents (and indices) are only valid in a certain range of property values. To simplify the identification of the controlling merit exponent, it is suggested that so called control area diagrams are used. These diagrams consist of a number of domains, each showing the active constraints and the controlling merit exponent. It is shown that the merit exponents play a crucial role when the control area diagram (CAD) is set up. The principles in the paper are developed for mechanically loaded components and are illustrated for engineering beams with two or three geometric variables.

  11. Development of Knitted Materials Selection for Compression Underwear

    Directory of Open Access Journals (Sweden)

    Cheng Zhe

    2017-06-01

    Full Text Available The presented research deals with the development of comfortable male underwear taking into account the development of pattern block methods and the analysis of the relationships existing between the compression pressure, the knitted materials properties, and some push-up effects. The main aim of this study is to achieve the technical selection of the materials based on KES-FB evaluations.The ease value has been used as the main index to connect the structural design of underwear, on one hand, and the body sizes, on other hand. A “bodyshell” system for testing the soft tissue of male bodies by FlexiForce sensor has been implemented. The pressures under the shells at six different places on the male body with ease changing have been tested.The collected results including maximum-possible pressure and material tensile indexes measured thanks to KES-FB have been analyzed in order to find the most relevant indexes of the material properties. A mathematical equations based on relationships combining theoretical model with practical application have been established. These equations will be helpful for the consumers and designers to select “the suitable knitting materials for male underwear” and they can be used too in the perspective of parameterization in CAD, in order to improve product developments efficiency.

  12. Significance of ITER IWS Material Selection and Qualification

    Science.gov (United States)

    Mehta, Bhoomi K.; Raval, Jigar; Maheshwari, Abha; Laad, Rahul; Singh, Gurlovleen; Pathak, Haresh

    2017-04-01

    In-Wall Shielding (IWS) is one of the important components of ITER Vacuum Vessel (VV) which fills the space between double walls of VV with cooling water. Procurement Arrangement (PA) for IWS has been signed with Indian Domestic Agency (INDA). Procurement of IWS materials, fabrication of IWS blocks and its delivery to respective Domestic Agency (DA) and ITER Organization (IO) are the main scope of this PA. Hence, INDIA is the only country which is contributing to VV IWS among all seven ITER partners. The main functions of the IWS are to provide Neutron Shielding with blanket, VV shells and water during plasma operations and to reduce ripple of the Toroidal Magnetic Field. To meet these functional requirements IWS blocks are made up of special materials (Borated Steels SS304 B4 & SS304 B7, Ferritic Steels SS 430, Austenitic Steel SS 316 L (N)-IG, XM-19 and Inconel-625) which are qualified, reliable and traceable for the design assessment. The choice of these materials has a significant influence on performance, maintainability, licensing, detailed design parameters and waste disposal. The main reasons for the materials selected for IWS are its high mechanical strength at operating temperatures, water chemistry properties, excellent fabrication characteristics and low cost relative to other similar materials. All the materials are qualified with respect to their respective codes (ASTM/EN standards with additional requirements as described in RCC-MR code 2007) and ITER requirements. Agreed Notified Body (ANB) has control conformity of materials certificates with approved material specification and traceability procedure for Safety Important Component (SIC). The procurement strategy for all the IWS materials has been developed in close collaboration with IO, ANB and Industries as per Product Procurement Specification (PPS). The R&D for sample, bulk material production, testing, inspection and handling as required are carried out by IN DA and IO. At present almost all

  13. Characterization of selected LDEF polymer matrix resin composite materials

    Science.gov (United States)

    Young, Philip R.; Slemp, Wayne S.; Witte, William G., Jr.; Shen, James Y.

    1991-01-01

    The characterization of selected graphite fiber reinforced epoxy (934 and 5208) and polysulfone (P1700) matrix resin composite materials which received 5 years and 10 months of exposure to the LEO environment on the Long Duration Exposure Facility is reported. Resin loss and a decrease in mechanical performance as well as dramatic visual effects were observed. However, chemical characterization including infrared, thermal, and selected solution property measurements showed that the molecular structure of the polymeric matrix had not changed significantly in response to this exposure. The potential effect of a silicon-containing molecular contamination of these specimens is addressed.

  14. Use of casual tree method for investigation of incidents and accidents involving radioactive materials

    International Nuclear Information System (INIS)

    Vasconcelos, Vanderley de; Senne Junior, Murillo; Marques, Raissa Oliveira

    2013-01-01

    There are many methodologies used for investigation of accidents to facilitate the search of the factors that cause these events in different areas of industry. These can be called proactive methods, if they are used before the occurrence of the events, or reactive methods that are applied after the occurrence of the incident or accident, and are used as a basis of information to prevent further events. One of these methods is the Causal Tree Method (CTM). The basic idea of this technique is that incidents and accidents result from variations in usual processes. These variations can be related to the individual, the task, the material or the environment. The tree starts with the end event (incident or accident) and works backwards. The facts relating to the end event are used in the construction of the causal tree. The end event is the starting point and only the facts that contributed to the incident or accident should be selected. The analyst has to identify and list the variations and then display them in the analytic tree, showing causal relations. The objective of this paper is to test the application of the CTM method in investigation of incidents and accidents involving radioactive materials, in order to evaluate its efficiency on finding the typical factors causing these events. (author)

  15. Selection of materials with potential in sensible thermal energy storage

    International Nuclear Information System (INIS)

    Fernandez, A.I.; Martinez, M.; Segarra, M.; Martorell, I.; Cabeza, L.F.

    2010-01-01

    Thermal energy storage is a technology under investigation since the early 1970s. Since then, numerous new applications have been found and much work has been done to bring this technology to the market. Nevertheless, the materials used either for latent or for sensible storage were mostly investigated 30 years ago, and the research has lead to improvement in their performance under different conditions of applications. In those years a significant number of new materials were developed in many fields other than storage and energy, but a great effort to characterize and classify these materials was done. Taking into account the fact that thousands of materials are known and a large number of new materials are developed every year, the authors use the methodology for materials selection developed by Prof. Ashby to give an overview of other materials suitable to be used in thermal energy storage. Sensible heat storage at temperatures between 150 and 200 C is defined as a case study and two different scenarios were considered: long term sensible heat storage and short term sensible heat storage. (author)

  16. Selecting a radiation tolerant piezoelectric material for nuclear reactor applications

    Energy Technology Data Exchange (ETDEWEB)

    Parks, D. A.; Reinhardt, B. T.; Tittmann, B. R. [Department of Engineering Science and Mechanics, Penn State, University Park, PA 16803 (United States)

    2013-01-25

    Bringing systems for online monitoring of nuclear reactors to fruition has been delayed by the lack of suitable ultrasonic sensors. Recent work has demonstrated the capability of an AlN sensor to perform ultrasonic evaluation in an actual nuclear reactor. Although the AlN demonstrated sustainability, no loss in signal amplitude and d{sub 33} up to a fast and thermal neutron fluence of 1.85 Multiplication-Sign 1018 n/cm{sup 2} and 5.8 Multiplication-Sign 1018 n/cm{sup 2} respectively, no formal process to selecting a suitable sensor material was made. It would be ideal to use first principles approaches to somehow reduce each candidate piezoelectric material to a simple ranking showing directly which materials one should expect to be most radiation tolerant. However, the complexity of the problem makes such a ranking impractical and one must appeal to experimental observations. This should not be of any surprise to one whom is familiar with material science as most material properties are obtained in this manner. Therefore, this work adopts a similar approach, the mechanisms affecting radiation tolerance are discussed and a good engineering sense is used for material qualification of the candidate piezoelectric materials.

  17. Visual search in scenes involves selective and non-selective pathways

    Science.gov (United States)

    Wolfe, Jeremy M; Vo, Melissa L-H; Evans, Karla K; Greene, Michelle R

    2010-01-01

    How do we find objects in scenes? For decades, visual search models have been built on experiments in which observers search for targets, presented among distractor items, isolated and randomly arranged on blank backgrounds. Are these models relevant to search in continuous scenes? This paper argues that the mechanisms that govern artificial, laboratory search tasks do play a role in visual search in scenes. However, scene-based information is used to guide search in ways that had no place in earlier models. Search in scenes may be best explained by a dual-path model: A “selective” path in which candidate objects must be individually selected for recognition and a “non-selective” path in which information can be extracted from global / statistical information. PMID:21227734

  18. ERG review of waste package container materials selection and corrosion

    International Nuclear Information System (INIS)

    Moak, D.P.; Perrin, J.S.

    1986-07-01

    The Engineering Review Group (ERG) was established by the Office of Nuclear Waste Isolation (ONWI) to help evaluate engineering-related issues in the US Department of Energy's nuclear waste repository program. The October 1984 meeting of the ERG reviewed the waste package container materials selection and corrosion. This report documents the ERG's comments and recommendations on these subjects and the ONWI response to the specific points raised by the ERG

  19. Selection and evaluation of materials for thermoelectric applications II

    Energy Technology Data Exchange (ETDEWEB)

    Sharp, J W

    1997-07-01

    In good thermoelectrics phonons have short mean free paths, and charge carriers have long ones. The other requirements are a multivalley band structure and a band gap greater than 0.1 eV for the 200 to 300 K temperature range. The author discusses the use of solid state physics and chemistry concepts, along with atomic and crystal structure data, to select the new materials most likely to meet these criteria.

  20. Incidents of illicit trafficking and other unauthorized activities involving nuclear and other radioactive materials (1993-2005)

    International Nuclear Information System (INIS)

    2010-01-01

    The confirmed incidents of illicit trafficking and other unauthorized activities involving nuclear and other radioactive materials between 1993-2005 shows that, 27% involved nuclear materials, 62% radioactive materials,7% involved both nuclear and other radioactive materials while the remainder involved other radioactive and non radioactive materials.Also 80% of nuclear material which was recovered during the same period was not reported as stolen or lost.

  1. Material Selection for Microchannel Heatsink: Conjugate Heat Transfer Simulation

    Science.gov (United States)

    Uday Kumar, A.; Javed, Arshad; Dubey, Satish K.

    2018-04-01

    Heat dissipation during the operation of electronic devices causes rise in temperature, which demands an effective thermal management for their performance, life and reliability. Single phase liquid cooling in microchannels is an effective and proven technology for electronics cooling. However, due to the ongoing trends of miniaturization and developments in the microelectronics technology, the future needs of heat flux dissipation rate are expected to rise to 1 kW/cm2. Air cooled systems are unable to meet this demand. Hence, liquid cooled heatsinks are preferred. This paper presents conjugate heat transfer simulation of single phase flow in microchannels with application to electronic cooling. The numerical model is simulated for different materials: copper, aluminium and silicon as solid and water as liquid coolant. The performances of microchannel heatsink are analysed for mass flow rate range of 20-40 ml/min. The investigation has been carried out on same size of electronic chip and heat flux in order to have comparative study of different materials. This paper is divided into two sections: fabrication techniques and numerical simulation for different materials. In the first part, a brief discussion of fabrication techniques of microchannel heatsink have been presented. The second section presents conjugate heat transfer simulation and parametric investigation for different material microchannel heatsink. The presented study and findings are useful for selection of materials for microchannel heatsink.

  2. Planning and preparing for emergency response to transport accidents involving radioactive material. Safety guide

    International Nuclear Information System (INIS)

    2005-01-01

    The objective of this Safety Guide is to provide guidance to the public authorities and others (including consignors, carriers and emergency response authorities) who are responsible for developing and establishing emergency arrangements for dealing effectively and safely with transport accidents involving radioactive material. It may assist those concerned with establishing the capability to respond to such transport emergencies. It provides guidance for those Member States whose involvement with radioactive material is just beginning. It also provides guidance for those Member States that have already developed their radioactive material industries and the attendant emergency plans but that may need to review and improve these plans

  3. Stochastic isotropic hyperelastic materials: constitutive calibration and model selection

    Science.gov (United States)

    Mihai, L. Angela; Woolley, Thomas E.; Goriely, Alain

    2018-03-01

    Biological and synthetic materials often exhibit intrinsic variability in their elastic responses under large strains, owing to microstructural inhomogeneity or when elastic data are extracted from viscoelastic mechanical tests. For these materials, although hyperelastic models calibrated to mean data are useful, stochastic representations accounting also for data dispersion carry extra information about the variability of material properties found in practical applications. We combine finite elasticity and information theories to construct homogeneous isotropic hyperelastic models with random field parameters calibrated to discrete mean values and standard deviations of either the stress-strain function or the nonlinear shear modulus, which is a function of the deformation, estimated from experimental tests. These quantities can take on different values, corresponding to possible outcomes of the experiments. As multiple models can be derived that adequately represent the observed phenomena, we apply Occam's razor by providing an explicit criterion for model selection based on Bayesian statistics. We then employ this criterion to select a model among competing models calibrated to experimental data for rubber and brain tissue under single or multiaxial loads.

  4. Materials Selection And Fabrication Practices For Food Processing Equipment Manufacturers In Uganda

    Directory of Open Access Journals (Sweden)

    John Baptist Kirabira

    2017-08-01

    Full Text Available The food processing industry is one of the fast-growing sub-sectors in Uganda. The industry which is majorly composed of medium and small scale firms depends on the locally developed food processing equipment. Due to lack of effective materials selection practices employed by the equipment manufacturers the materials normally selected for most designs are not the most appropriate ones hence compromising the quality of the equipment produced. This has not only led to poor quality food products due to contamination but could also turn out health hazardous to the consumers of the food products. This study involved the assessment of the current materials selection and fabrication procedures used by the food processing equipment manufacturers with a view of devising best practices that can be used to improve the quality of the food products processed by the locally fabricated equipment. Results of the study show that designers experience biasness and desire to minimize cost compromise the materials selection procedure. In addition to failing to choose the best material for a given application most equipment manufacturers are commonly fabricating equipment with inadequate surface finish and improper weldments. This hinders the equipments ability to meet food hygiene standards.

  5. Assessment of Heat Hazard during the Polymerization of Selected Light-Sensitive Dental Materials.

    Science.gov (United States)

    Janeczek, Maciej; Herman, Katarzyna; Fita, Katarzyna; Dudek, Krzysztof; Kowalczyk-Zając, Małgorzata; Czajczyńska-Waszkiewicz, Agnieszka; Piesiak-Pańczyszyn, Dagmara; Kosior, Piotr; Dobrzyński, Maciej

    2016-01-01

    Introduction. Polymerization of light-cured dental materials used for restoration of hard tooth tissue may lead to an increase in temperature that may have negative consequence for pulp vitality. Aim. The aim of this study was to determine maximum temperatures reached during the polymerization of selected dental materials, as well as the time that is needed for samples of sizes similar to those used in clinical practice to reach these temperatures. Materials and Methods. The study involved four composite restorative materials, one lining material and a dentine bonding agent. The polymerization was conducted with the use of a diode light-curing unit. The measurements of the external surface temperature of the samples were carried out using the Thermovision®550 thermal camera. Results. The examined materials significantly differed in terms of the maximum temperatures values they reached, as well as the time required for reaching the temperatures. A statistically significant positive correlation of the maximum temperature and the sample weight was observed. Conclusions. In clinical practice, it is crucial to bear in mind the risk of thermal damage involved in the application of light-cured materials. It can be reduced by using thin increments of composite materials.

  6. Assessment of Heat Hazard during the Polymerization of Selected Light-Sensitive Dental Materials

    Directory of Open Access Journals (Sweden)

    Maciej Janeczek

    2016-01-01

    Full Text Available Introduction. Polymerization of light-cured dental materials used for restoration of hard tooth tissue may lead to an increase in temperature that may have negative consequence for pulp vitality. Aim. The aim of this study was to determine maximum temperatures reached during the polymerization of selected dental materials, as well as the time that is needed for samples of sizes similar to those used in clinical practice to reach these temperatures. Materials and Methods. The study involved four composite restorative materials, one lining material and a dentine bonding agent. The polymerization was conducted with the use of a diode light-curing unit. The measurements of the external surface temperature of the samples were carried out using the Thermovision®550 thermal camera. Results. The examined materials significantly differed in terms of the maximum temperatures values they reached, as well as the time required for reaching the temperatures. A statistically significant positive correlation of the maximum temperature and the sample weight was observed. Conclusions. In clinical practice, it is crucial to bear in mind the risk of thermal damage involved in the application of light-cured materials. It can be reduced by using thin increments of composite materials.

  7. SELECTION OF MICROORGANISMS FOR FERMENTATION OF MEAT MATERIALS

    Directory of Open Access Journals (Sweden)

    Danylenko S. G.

    2014-08-01

    Full Text Available Principal criteria for the selection of microorganisms with a wide range of biological and technological properties for fermentation of raw meats are considered. Attention is paid to the main groups of microorganisms such as Micrococсus, Staphylococcus, Lactobacillus, Bifidobacterium and Propionibacterium which are promising for creation of bacterial preparations. To create bacterial preparations, the basic criteria of selection for microorganisms were determined as follows: the ability of microorganisms to be developed within the specific ecological niche (raw meat materials and their influence on flavor characteristics of the final product under the conditions of intensification of production technologies of meat products. Methods used for search and retrieval of technologically promising strains from different natural sources (fresh meats, minced meats, meat, dairy and sour-milk products, vegetables, fruit, brines and mixtures for salting are considered.

  8. Material Selection and Characterization for High Gradient RF Applications

    CERN Document Server

    Arnau-Izquierdo, G; Heikkinen, S; Ramsvik, T; Sgobba, Stefano; Taborelli, M; Wuensch, W

    2007-01-01

    The selection of candidate materials for the accelerating cavities of the Compact Linear Collider (CLIC) is carried out in parallel with high power RF testing. The maximum DC breakdown field of copper, copper alloys, refractory metals, aluminium and titanium have been measured with a dedicated setup. Higher maximum fields are obtained for refractory metals and for titanium, which exhibits, however, important damages after conditioning. Fatigue behaviour of copper alloys has been studied for surface and bulk by pulsed laser irradiation and ultrasonic excitation, respectively. The selected copper alloys show consistently higher fatigue resistance than copper in both experiments. In order to obtain the best local properties in the device a possible solution is a bi-metallic assembly. Junctions of molybdenum and copper-zirconium UNS C15000 alloy, achieved by HIP (Hot Isostatic Pressing) diffusion bonding or explosion bonding were evaluated for their mechanical strength. The reliability of the results obtained wit...

  9. Materials Compatibility Testing in RSRM ODC: Free Cleaner Selection

    Science.gov (United States)

    Keen, Jill M.; Sagers, Neil W.; McCool, Alex (Technical Monitor)

    2001-01-01

    Government regulations have mandated production phase-outs of a number of solvents, including 1,1,1-trichloroethane, an ozone-depleting chemical (ODC). This solvent was used extensively in the production of the Reusable Solid Rocket Motors (RSRMs) for the Space Shuttle. Many tests have been performed to identify replacement cleaners. One major area of concern in the selection of a new cleaner has been compatibility. Some specific areas considered included cleaner compatibility with non-metallic surfaces, painted surfaces, support materials such as gloves and wipers as well as corrosive properties of the cleaners on the alloys used on these motors. The intent of this paper is to summarize the test logic, methodology, and results acquired from testing the many cleaner and material combinations.

  10. PLASTICITY OF SELECTED METALLIC MATERIALS IN DYNAMIC DEFORMATION CONDITIONS

    Directory of Open Access Journals (Sweden)

    Jacek PAWLICKI

    2014-06-01

    Full Text Available Characteristics of a modernized flywheel machine has been presented in the paper. The laboratory stand enables to perform dynamic tensile tests and impact bending with a linear velocity of the enforcing element in the range of 5÷40 m/s. A new data acquisition system, based on the tensometric sensors, allows for significant qualitative improvement of registered signals. Some preliminary dynamic forming tests were performed for the selected group of metallic materials. Subsequent microstructural examinations and identification of the fracture type enabled to describe a correlation between strain rate, strain and microstructure.

  11. VOCs and odors: key factors in selecting `green` building materials?

    Energy Technology Data Exchange (ETDEWEB)

    Coombs, C. [Steven Winter Associates Inc., Norwalk, CT and Washington DC (United States)

    1998-12-01

    The current state of knowledge available for selecting building materials on the basis of emissions of volatile organic compounds (VOCs) and odors is reviewed. The significance of VOCs and odors in building materials is related to their role in influencing indoor air quality. As far as toxicity is concerned, many of the VOCs detected in indoor air are relatively inert when considered singly. They are not however, unimportant because in actual fact they are invariably found in mixtures some of which can be toxic. Although knowledge of VOCs is incomplete, it is important to specify ozone-resistant polymeric building products, i.e. those that are chemically stable and inert to oxidation. In addition to VOCs, attention should also be focused on semi-volatile organic compounds (SVOCs) since they are even more persistent than VOCs and tend to offgas for prolonged periods of time. Similarly, it is reasonable to specify low-odor materials. Inclusion of issues related to complex indoor chemistry, less volatile emissions, in addition to VOCs and odor, should in time result in expanded choices of building materials that promote indoor air quality. 16 refs.,2 tabs.

  12. Windscale inquiry. A selected list of material based on the DOE/DTp library

    Energy Technology Data Exchange (ETDEWEB)

    Lambert, C M [comp.

    1981-01-01

    The nuclear debate, far from being concluded by the Windscale decision, was in fact opened up and its scope widened to take into account the political, international, environmental and social issues involved. This debate continues and the selection of literature presented here aims to illustrate all aspects of the Inquiry and its implications. The material is presented in two main sections. Section A is concerned with the Inquiry itself: the proceedings, the report and the government's decision. Section B presents a selection of the literature and debate that resulted.

  13. Organizational influence on the occurrence of work accidents involving exposure to biological material.

    Science.gov (United States)

    Marziale, Maria Helena Palucci; Rocha, Fernanda Ludmilla Rossi; Robazzi, Maria Lúcia do Carmo Cruz; Cenzi, Camila Maria; dos Santos, Heloisa Ehmke Cardoso; Trovó, Marli Elisa Mendes

    2013-01-01

    to analyze work accidents involving exposure to biological materials which took place among personnel working in nursing and to evaluate the influence of the organizational culture on the occurrence of these accidents. a retrospective, analytical study, carried out in two stages in a hospital that was part of the Network for the Prevention of Work Accidents. The first stage involved the analysis of the characteristics of the work accidents involving exposure to biological materials as recorded over a seven-year period by the nursing staff in the hospital studied, and registered in the Network databank. The second stage involved the analysis of 122 nursing staff members' perception of the institutional culture, who were allocated to the control group (workers who had not had an accident) and the case group (workers who had had an accident). 386 accidents had been recorded: percutaneous lesions occurred in 79% of the cases, needles were the materials involved in 69.7% of the accidents, and in 81.9% of the accident there was contact with blood. Regarding the influence of the organizational culture on the occurrence of accidents, the results obtained through the analysis of the two groups did not demonstrate significant differences between the average scores attributed by the workers in each organizational value or practice category. It is concluded that accidents involving exposure to biological material need to be avoided, however, it was not possible to confirm the influence of organizational values or practices on workers' behavior concerning the occurrence of these accidents.

  14. Selected topics in special nuclear materials safeguard system design

    International Nuclear Information System (INIS)

    King, L.L.; Thatcher, C.D.; Clarke, J.D.; Rodriguez, M.P.

    1991-01-01

    During the past two decades the improvements in circuit integration have given rise to many new applications in digital processing technology by continuously reducing the unit cost of processing power. Along with this increase in processing power a corresponding decrease in circuit volume has been achieved. Progress has been so swift that new classes of applications become feasible every 2 or 3 years. This is especially true in the application of proven new technology to special nuclear materials (SNM) safeguard systems. Several areas of application were investigated in establishing the performance requirements for the SNM safeguard system. These included the improvements in material control and accountability and surveillance by using multiple sensors to continuously monitor SNM inventory within the selected value(s); establishing a system architecture to provide capabilities needed for present and future performance requirements; and limiting operating manpower exposure to radiation. This paper describes two selected topics in the application of state-of-the-art, well-proven technology to SNM safeguard system design

  15. Information resources and material selection in bonded restorations among Korean dentists.

    Science.gov (United States)

    Chang, Juhea; Kim, Hae-Young; Cho, Byeong Hoon; Lee, In Bog; Son, Ho Hyun

    2009-12-01

    To elucidate how dentists access knowledge sources when choosing adhesive agents for bonded restoration and whether these resources influenced the selection of materials. A national survey was carried out involving dentists in South Korea. The questionnaire included the status of the operator, clinical techniques, and materials. A total of 12,193 e-mails were distributed, 2632 were opened by recipients, and 840 responses were collected. For primary information resources in material selection, 55.8% (n = 469) of the responders mentioned continuing education. This selection criteria varied according to the working status of the clinician (p choice of bonding system was influenced by of the length of the career (p < 0.0001), and the preferred bonding systems differed according to the source of the information (p = 0.035). The popular bonding systems were not ranked according to the bonding strategy, but a preference was found for specific brands or manufacturers. To decrease the confusion of clinicians related to the selection of bonding materials, evidence-based guidelines need to be comprehensibly organized and efficiently approached in clinics.

  16. Design and selection of materials for sodium cooled fast reactors

    International Nuclear Information System (INIS)

    Chetal, S.C.

    2011-01-01

    Sodium cooled fast reactors are currently in operation, under construction or under design by a number of countries. The design of sodium cooled fast reactor is covered by French RCC - MR code and ASME code NH. The codes cover rules as regards to materials, design and construction. These codes do not cover the effect of irradiation and environment. Elevated temperature design criteria in nuclear codes are much stringent in comparison to non nuclear codes. Sodium corrosion is not an issue in selection of materials provided oxygen impurity in sodium is controlled for which excellent reactor operating experience is available. Austenitic stainless steels have remained the choice for the permanent structures of primary sodium system. Stabilized austenitic stainless steel are rejected because of poor operating experience and non inclusion in the design codes. Route for improved creep behaviour lies in compositional modifications in 316 class steel. However, the weldability needs to be ensured. For cold leg component is non creep regime, SS 304 class steel is favoured from overall economics. Enhanced fuel burn up can be realized by the use of 9-12%Cr 1%Mo class steel for the wrapper of MOX fuel design, and cladding and wrapper for metal fuel reactors. Minor compositional modifications of 20% cold worked 15Cr-15Ni class austenitic stainless steel will be a strong candidate for the cladding of MOX fuel design in the short term. Long term objective for the cladding will be to develop oxide dispersion strengthened steel. 9%Cr 1%Mo class steel (Gr 91) is an ideal choice for integrated once through sodium heated steam generators. One needs to incorporate operating experience from reactors and thermal power stations, industrial capability and R and D feedback in preparing the technical specifications for procurement of wrought products and welding consumables to ensure reliable operation of the components and systems over the design life. The paper highlights the design approach

  17. Development of the material selection practice - a study exploring articulation of material requirements

    DEFF Research Database (Denmark)

    Lenau, Torben Anker; Hasling, Karen Marie

    2014-01-01

    indicates that students focus on technical requirements when using the matrix and justifying their selection of materials. This is surprising since the students attend an arts and crafts oriented design school and are encouraged and guided to consider non-technical requirements, as part of the course where...... the matrix is introduced. A possible reason for the undesired behavior could be that students are allowed very freely to define their own matrices, having only little guidance to which requirements to use. A more formal procedure for making the material matrices is therefore proposed. The procedure requires...

  18. Planning and Preparing for Emergency Response to Transport Accidents Involving Radioactive Material. Safety Guide

    International Nuclear Information System (INIS)

    2009-01-01

    This Safety Guide provides guidance on various aspects of emergency planning and preparedness for dealing effectively and safely with transport accidents involving radioactive material, including the assignment of responsibilities. It reflects the requirements specified in Safety Standards Series No. TS-R-1, Regulations for the Safe Transport of Radioactive Material, and those of Safety Series No. 115, International Basic Safety Standards for Protection against Ionizing Radiation and for the Safety of Radiation Sources. Contents: 1. Introduction; 2. Framework for planning and preparing for response to accidents in the transport of radioactive material; 3. Responsibilities for planning and preparing for response to accidents in the transport of radioactive material; 4. Planning for response to accidents in the transport of radioactive material; 5. Preparing for response to accidents in the transport of radioactive material; Appendix I: Features of the transport regulations influencing emergency response to transport accidents; Appendix II: Preliminary emergency response reference matrix; Appendix III: Guide to suitable instrumentation; Appendix IV: Overview of emergency management for a transport accident involving radioactive material; Appendix V: Examples of response to transport accidents; Appendix VI: Example equipment kit for a radiation protection team; Annex I: Example of guidance on emergency response to carriers; Annex II: Emergency response guide.

  19. Assessment of materials selection and performance for direct-coal- liquefaction plants in the United States

    Energy Technology Data Exchange (ETDEWEB)

    Olsen, A.R.; Judkins, R.R.; Keiser, J.R.

    1996-09-01

    Several direct coal liquefaction processes have been demonstrated at the pilot plant level in the United States. Presently only one plant remains operational, namely, the Hydrocarbon Technologies, Inc., 4.0- ton-per-day process development unit in Lawrenceville, New Jersey. The period from 1974 to 1982 saw the greatest amount of development of direct coal liquefaction in the United States with four major pilot plants being devoted to variants of this technology. The plants included the SRC-I plant at Wilsonville, Alabama, which operated from 1974 to 1992; the SRC-I/II plant at Fort Lewis, Washington, which operated from 1974 to 1981; the H-Coal plant at Catlettsburg, Kentucky, which operated from 1980 to 1982; and the Exxon Coal Liquefaction Pilot Plant at Baytown, Texas, which operated from 1980 to 1982. Oak Ridge National Laboratory scientists and engineers were actively involved in many phases and technical disciplines at all four of these plants, especially in materials testing, evaluation, and failure analyses. In addition, ORNL materials scientists and engineers conducted reviews of the demonstration and commercial plant designs for materials selections. The ORNL staff members worked closely with materials engineers at the pilot plants in identifying causes of materials degradation and failures, and in identifying solutions to these problems. This report provides a comprehensive summary of those materials activities. Materials performance data from laboratory and coal liquefaction pilot plant tests, failure analyses, and analyses of components after use in pilot plants were reviewed and assessed to determine the extent and causes of materials degradation in direct coal liquefaction process environments. Reviews of demonstration and commercial plant design documents for materials selections were conducted. These reviews and assessments are presented to capture the knowledge base on the most likely materials of construction for direct coal liquefaction plants.

  20. Strategies for selecting effective patient nutrition education materials.

    Science.gov (United States)

    Clayton, Laura H

    2010-10-01

    Nutrition and diet therapy are at the center of health promotion activities and self-management of chronic diseases. To assist an individual in making informed decisions regarding his or her diet and increase adherence to dietary recommendations or treatments, healthcare professionals must select health information that is appropriate to the client's level of understanding. A systematic approach in the evaluation of patient education material, whether in print or on the World Wide Web, must focus on the information's content, literacy level, graphical displays, layout and typography, motivating principles, cultural relevance, and feasibility. Additional criteria should be evaluated when accessing Web sites and include source, site credibility, conflict of interest, disclaimer, disclosure, navigation, and interactivity information.

  1. Materials selection for oxide-based resistive random access memories

    International Nuclear Information System (INIS)

    Guo, Yuzheng; Robertson, John

    2014-01-01

    The energies of atomic processes in resistive random access memories (RRAMs) are calculated for four typical oxides, HfO 2 , TiO 2 , Ta 2 O 5 , and Al 2 O 3 , to define a materials selection process. O vacancies have the lowest defect formation energy in the O-poor limit and dominate the processes. A band diagram defines the operating Fermi energy and O chemical potential range. It is shown how the scavenger metal can be used to vary the O vacancy formation energy, via controlling the O chemical potential, and the mean Fermi energy. The high endurance of Ta 2 O 5 RRAM is related to its more stable amorphous phase and the adaptive lattice rearrangements of its O vacancy

  2. Material selection and corrosion control practices in petroleum production

    International Nuclear Information System (INIS)

    Tuttle, R.N.

    1980-01-01

    The intent of this paper is to review briefly the current state of the art and to discuss some of the anticipated future oil and gas drilling and production activities which may challenge the materials selection and corrosion technologies. The current state of art discussions in this paper have been augmented by providing a list of references so that interested engineers may delve into each subject in more detail as desired. The technological areas which appear to require additional input to meet future needs include high strength tubular goods for sour gas service, corrosion resistant high strength alloys, definition of the effects of pressure, temperature, and fluid composition on corrosion behavior, and fatigue properties of various steels in seawater

  3. Materials selection for oxide-based resistive random access memories

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Yuzheng; Robertson, John [Engineering Department, Cambridge University, Cambridge CB2 1PZ (United Kingdom)

    2014-12-01

    The energies of atomic processes in resistive random access memories (RRAMs) are calculated for four typical oxides, HfO{sub 2}, TiO{sub 2}, Ta{sub 2}O{sub 5}, and Al{sub 2}O{sub 3}, to define a materials selection process. O vacancies have the lowest defect formation energy in the O-poor limit and dominate the processes. A band diagram defines the operating Fermi energy and O chemical potential range. It is shown how the scavenger metal can be used to vary the O vacancy formation energy, via controlling the O chemical potential, and the mean Fermi energy. The high endurance of Ta{sub 2}O{sub 5} RRAM is related to its more stable amorphous phase and the adaptive lattice rearrangements of its O vacancy.

  4. Examination of Signatures of Recent Positive Selection on Genes Involved in Human Sialic Acid Biology.

    Science.gov (United States)

    Moon, Jiyun M; Aronoff, David M; Capra, John A; Abbot, Patrick; Rokas, Antonis

    2018-03-28

    Sialic acids are nine carbon sugars ubiquitously found on the surfaces of vertebrate cells and are involved in various immune response-related processes. In humans, at least 58 genes spanning diverse functions, from biosynthesis and activation to recycling and degradation, are involved in sialic acid biology. Because of their role in immunity, sialic acid biology genes have been hypothesized to exhibit elevated rates of evolutionary change. Consistent with this hypothesis, several genes involved in sialic acid biology have experienced higher rates of non-synonymous substitutions in the human lineage than their counterparts in other great apes, perhaps in response to ancient pathogens that infected hominins millions of years ago (paleopathogens). To test whether sialic acid biology genes have also experienced more recent positive selection during the evolution of the modern human lineage, reflecting adaptation to contemporary cosmopolitan or geographically-restricted pathogens, we examined whether their protein-coding regions showed evidence of recent hard and soft selective sweeps. This examination involved the calculation of four measures that quantify changes in allele frequency spectra, extent of population differentiation, and haplotype homozygosity caused by recent hard and soft selective sweeps for 55 sialic acid biology genes using publicly available whole genome sequencing data from 1,668 humans from three ethnic groups. To disentangle evidence for selection from confounding demographic effects, we compared the observed patterns in sialic acid biology genes to simulated sequences of the same length under a model of neutral evolution that takes into account human demographic history. We found that the patterns of genetic variation of most sialic acid biology genes did not significantly deviate from neutral expectations and were not significantly different among genes belonging to different functional categories. Those few sialic acid biology genes that

  5. Emergency response planning and preparedness for transport accidents involving radioactive material

    International Nuclear Information System (INIS)

    1988-01-01

    The purpose of this Guide is to provide assistance to public authorities and others (including consignors and carriers of radioactive materials) who are responsible for ensuring safety in establishing and developing emergency response arrangements for responding effectively to transport accidents involving radioactive materials. This Guide is concerned mainly with the preparation of emergency response plans. It provides information which will assist those countries whose involvement with radioactive materials is just beginning and those which have already developed their industries involving radioactive materials and attendant emergency plans, but may need to review and improve these plans. The need for emergency response plans and the ways in which they are implemented vary from country to country. In each country, the responsible authorities must decide how best to apply this Guide, taking into account the actual shipments and associated hazards. In this Guide the emergency response planning and response philosophy are outlined, including identification of emergency response organizations and emergency services that would be required during a transport accident. General consequences which could prevail during an accident are described taking into account the IAEA Regulations for the Safe Transport of Radioactive Material. 43 refs, figs and tabs

  6. Selection of steam generator materials for sodium cooled fast breeders

    International Nuclear Information System (INIS)

    Berge, P.

    1977-01-01

    The sodium water heat exchangers are now considered as the stumbling block in the development of liquid metal cooled fast breeders, due to the risk of sodium-water reactions. The selection of the materials for these tube-bundles has been very broad, for the different existing, or in-project, reactors in the world: low alloy 2 1/4 Cr - 1 Mo steels (unstabilized or stabilized); 9 Cr - 1 Mo ferritic steel; 18 Cr - 10 Ni austenitic stainless steels; alloy 800. On can also add other ferritic steels, as 9 Cr - 2 Mo stabilized, which are studied for this application. In the framework of the E.D.F.-C.E.A. working group a major effort was undertaken to study the characteristics of these various materials with respect to the main criteria governing construction of the tube bundles and their performance in service: mechanical characteristics at high temperature; fabrication and welding; behavior with respect to mass transfer in sodium; carburization and decarburization; corrosion resistance. The main lines and results of this program are described [fr

  7. Response to events involving the inadvertent movement or illicit trafficking of radioactive materials

    International Nuclear Information System (INIS)

    2004-08-01

    By international agreements, the movement of all radioactive materials within and between States should be subject to high standards of regulatory, administrative, safety and engineering controls to ensure that such movements are conducted in a safe and secure manner. In the case of nuclear materials, there are additional requirements for physical protection and accountability to ensure against threats of nuclear proliferation and to safeguard against any attempts at diversion. The results of the terrorist attacks of September 2001 emphasized the requirement for enhanced control and security of nuclear and radioactive materials. In this regard, measures are being taken to increase the global levels of physical protection and security for nuclear materials. Experience in many parts of the world continues to prove that movements of radioactive materials outside of the regulatory and legal frameworks continue to occur. Such movements may be either deliberate or inadvertent. Deliberate, illegal movements of radioactive materials, including nuclear material, for terrorist, political or illegal profit is generally understood to be illicit trafficking. The more common movements outside of regulatory control are inadvertent in nature. An example of an inadvertent movement might be the transport of steel contaminated by a melted radioactive source that was lost from proper controls. Such a shipment may present health and safety threats to the personnel involved as well as to the general public. States have the responsibility for combating illicit trafficking and inadvertent movements of radioactive materials. The IAEA co-operates with Member States and other international organizations in joint efforts to prevent incidents of illicit trafficking and inadvertent movements and to harmonize policies and measures by the provision of relevant advice through technical assistance and documents. As an example, the IAEA and the World Customs Organization (WCO) maintain a Memorandum

  8. Response to events involving the inadvertent movement or illicit trafficking of radioactive materials

    International Nuclear Information System (INIS)

    2002-09-01

    By international agreements, the movement of all radioactive materials within and between States should be subject to high standards of regulatory, administrative, safety and engineering controls to ensure that such movements are conducted in a safe and secure manner. In the case of nuclear materials, there are additional requirements for physical protection and accountability to ensure against threats of nuclear proliferation and to safeguard against any attempts at diversion. The results of the terrorist attacks of September 2001 emphasized the requirement for enhanced control and security of nuclear and radioactive materials. In this regard, measures are being taken to increase the global levels of physical protection and security for nuclear materials. Experience in many parts of the world continues to prove that movements of radioactive materials outside of the regulatory and legal frameworks continue to occur. Such movements may be either deliberate or inadvertent. Deliberate, illegal movements of radioactive materials, including nuclear material, for terrorist, political or illegal profit is generally understood to be illicit trafficking. The more common movements outside of regulatory control are inadvertent in nature. An example of an inadvertent movement might be the transport of steel contaminated by a melted radioactive source that was lost from proper controls. Such a shipment may present health and safety threats to the personnel involved as well as to the general public. States have the responsibility for combating illicit trafficking and inadvertent movements of radioactive materials. The IAEA co-operates with Member States and other international organizations in joint efforts to prevent incidents of illicit trafficking and inadvertent movements and to harmonize policies and measures by the provision of relevant advice through technical assistance and documents. As an example, the IAEA and the World Customs Organization (WCO) maintain a Memorandum

  9. Response to events involving the inadvertent movement or illicit trafficking of radioactive materials

    International Nuclear Information System (INIS)

    2002-08-01

    By international agreements, the movement of all radioactive materials within and between States should be subject to high standards of regulatory, administrative, safety and engineering controls to ensure that such movements are conducted in a safe and secure manner. In the case of nuclear materials, there are additional requirements for physical protection and accountability to ensure against threats of nuclear proliferation and to safeguard against any attempts at diversion. The results of the terrorist attacks of September 2001 emphasized the requirement for enhanced control and security of nuclear and radioactive materials. In this regard, measures are being taken to increase the global levels of physical protection and security for nuclear materials. Experience in many parts of the world continues to prove that movements of radioactive materials outside of the regulatory and legal frameworks continue to occur. Such movements may be either deliberate or inadvertent. Deliberate, illegal movements of radioactive materials, including nuclear material, for terrorist, political or illegal profit is generally understood to be illicit trafficking. The more common movements outside of regulatory control are inadvertent in nature. An example of an inadvertent movement might be the transport of steel contaminated by a melted radioactive source that was lost from proper controls. Such a shipment may present health and safety threats to the personnel involved as well as to the general public. States have the responsibility for combating illicit trafficking and inadvertent movements of radioactive materials. The IAEA co-operates with Member States and other international organizations in joint efforts to prevent incidents of illicit trafficking and inadvertent movements and to harmonize policies and measures by the provision of relevant advice through technical assistance and documents. As an example, the IAEA and the World Customs Organization (WCO) maintain a Memorandum

  10. Response to events involving the inadvertent movement or illicit trafficking of radioactive materials

    International Nuclear Information System (INIS)

    2003-08-01

    By international agreements, the movement of all radioactive materials within and between States should be subject to high standards of regulatory, administrative, safety and engineering controls to ensure that such movements are conducted in a safe and secure manner. In the case of nuclear materials, there are additional requirements for physical protection and accountability to ensure against threats of nuclear proliferation and to safeguard against any attempts at diversion. The results of the terrorist attacks of September 2001 emphasized the requirement for enhanced control and security of nuclear and radioactive materials. In this regard, measures are being taken to increase the global levels of physical protection and security for nuclear materials. Experience in many parts of the world continues to prove that movements of radioactive materials outside of the regulatory and legal frameworks continue to occur. Such movements may be either deliberate or inadvertent. Deliberate, illegal movements of radioactive materials, including nuclear material, for terrorist, political or illegal profit is generally understood to be illicit trafficking. The more common movements outside of regulatory control are inadvertent in nature. An example of an inadvertent movement might be the transport of steel contaminated by a melted radioactive source that was lost from proper controls. Such a shipment may present health and safety threats to the personnel involved as well as to the general public. States have the responsibility for combating illicit trafficking and inadvertent movements of radioactive materials. The IAEA co-operates with Member States and other international organizations in joint efforts to prevent incidents of illicit trafficking and inadvertent movements and to harmonize policies and measures by the provision of relevant advice through technical assistance and documents. As an example, the IAEA and the World Customs Organization (WCO) maintain a Memorandum

  11. Selection and evaluation of inner material candidates for Spanish high level radioactive waste canisters

    International Nuclear Information System (INIS)

    Puig, Francesc; Dies, Javier; Sevilla, Manuel; Pablo, Joan de; Pueyo, Juan Jose; Miralles, Lourdes; Martinez-Esparza, Aurora

    2007-01-01

    This paper summarizes the work carried out to analyse different alternatives related to the inner material selection of the Spanish high level waste canister for long term storage. The preliminary repository design considers granitic or clay formations, compacted bentonite sealing, corrosion allowing steel canisters and glass bead filling between the fuel assemblies and canister walls. This filling material will have the primary role of avoiding the possibility of a criticality event, which becomes an issue of major importance once the container is finally breached by corrosion and flooded by groundwater. In the first place, a complete set of requirements have been devised as evaluation criteria for candidate materials examination and selection; resulting in a compilation of demands significantly deeper and more exhaustive than any other similar work found in literature, including over 20 requirements and some other general aspects that could involve improvements in repository performance. Secondly, eight materials or material families (cast iron or steel, borosilicate glass, spinel, depleted uranium, dehydrated zeolites, hematite, phosphates and olivine) have been chosen and examined in detail, extracting some relevant conclusions. Either cast iron, borosilicate glass, spinel or depleted uranium are considered to look quite promising for the mentioned purpose. (authors)

  12. Guidelines for the Development of Instructional Materials Selection Policies. Handbook I.

    Science.gov (United States)

    Motomatsu, Nancy, Ed.

    This manual was developed to assist school district personnel in the development of policies and procedures for selecting instructional materials. The manual describes State of Washington laws and regulations that govern the selection, use, and disposal of instructional materials and presents criteria and guidelines for selecting materials. Also…

  13. Composite materials pipings: selection of basic materials and manufacturing process, quality control during manufacture

    International Nuclear Information System (INIS)

    Pays, M.F.

    1997-01-01

    The purpose of the paper is to present a summary of the knowledge acquired at the R and D on resins used as composite matrix, the resistance to hydrolysis and mechanical strength of pipings made from these materials, and on quality control during manufacture. The initial targets concerning the material selection, industrial manufacturing and quality control procedures are presented. The paper describes the results obtained concerning the investigation of the damage produced by hydrolysis in polyesters, vinyl esters and epoxides, the influence of temperature, reinforcement and the mechanical characterization of the tubing manufacturing. The performances of the nondestructive testings (radiography, ultrasonic controls, differential interferometry and infrared thermography) used are also reported. The paper ends with a further research and testings programme. (author)

  14. Emergency planning and preparedness for accidents involving radioactive materials used in medicine, industry, research and teaching

    International Nuclear Information System (INIS)

    1989-01-01

    This Safety Series book should be considered as a technical guide aimed at the users of radioactive materials and the appropriate local and national authorities. It does not represent a single solution to the problems involved but rather draws the outlines of the plans and procedures that have to be developed in order to mitigate the consequences of an accident, should one occur. The preparation of local and national plans should follow the technical recommendations provided in this publication, with due consideration given to local factors which might vary from country to country (e.g. governmental systems, local legislation, quantities of radioactive materials involved). Several types of accidents are described, together with their possible radiological consequences. The basic principles of the protective measures that should be applied are discussed, and the principles of emergency planning and the measures needed to maintain preparedness for an operational response to an accident are outlined

  15. Studies on selected polymeric materials using the photoacoustic spectroscopic technique

    International Nuclear Information System (INIS)

    Singh, Hukum

    2011-01-01

    Polymethylmethacrylate—graft—polybisphenol—A-carbonate (PMMA-G-PC) with 50% grafting is synthesized. The graft co-polymerization of methylmethacrylate (0.036 mol · lit −1 ) onto polybisphenol—A-carbonate (0.5 g) in the presence of a redox couple formed from potassium persulphate (40 mol · lit −1 ) and thio-urea (30 mmol · lit −1 ) in aqueous nitric acid (0.18 M, 100 ml) in air at (45±2) °C for 3.0 h. Condensation of (PMMA-G-PC) with N- [p-(carboxyl phenyl amino acetic acid)] hydrazide (PCPH) affords polybisphenol-A-carbonate-graft-polymethylmethacrylate hydrazide (PCGH). The photoacoustic (PA) spectra of (PCGH) are recorded in a wavelength range from 200 nm to 800 nm at a modulation frequency of 22 Hz, and compared with those of pure polybisphenol-A-carbonate (PC), (PMMA-G-PC) and (PCPH). In the present work, a non-destructive and non-contact analytical method, namely the photoacoustic technique, is successfully implemented for optical and thermal characterization of selected polymeric materials. The indigenous PA spectrometer used in the present study consists of a 300-W xenon arc lamp, a lock-in amplifier, a chopper, a (1/8)-m monochromator controlled by computer and a home-made PA cell. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

  16. Selective observation of charge storing ions in supercapacitor electrode materials.

    Science.gov (United States)

    Forse, Alexander C; Griffin, John M; Grey, Clare P

    2018-02-01

    Nuclear magnetic resonance (NMR) spectroscopy has emerged as a useful technique for probing the structure and dynamics of the electrode-electrolyte interface in supercapacitors, as ions inside the pores of the carbon electrodes can be studied separately from bulk electrolyte. However, in some cases spectral resolution can limit the information that can be obtained. In this study we address this issue by showing how cross polarisation (CP) NMR experiments can be used to selectively observe the in-pore ions in supercapacitor electrode materials. We do this by transferring magnetisation from 13 C nuclei in porous carbons to nearby nuclei in the cations ( 1 H) or anions ( 19 F) of an ionic liquid. Two-dimensional NMR experiments and CP kinetics measurements confirm that in-pore ions are located within Ångströms of sp 2 -hybridised carbon surfaces. Multinuclear NMR experiments hold promise for future NMR studies of supercapacitor systems where spectral resolution is limited. Copyright © 2017 University of Cambridge. Published by Elsevier Inc. All rights reserved.

  17. Global blending optimization of laminated composites with discrete material candidate selection and thickness variation

    DEFF Research Database (Denmark)

    Sørensen, Søren N.; Stolpe, Mathias

    2015-01-01

    rate. The capabilities of the method and the effect of active versus inactive manufacturing constraints are demonstrated on several numerical examples of limited size, involving at most 320 binary variables. Most examples are solved to guaranteed global optimality and may constitute benchmark examples...... but is, however, convex in the original mixed binary nested form. Convexity is the foremost important property of optimization problems, and the proposed method can guarantee the global or near-global optimal solution; unlike most topology optimization methods. The material selection is limited...... for popular topology optimization methods and heuristics based on solving sequences of non-convex problems. The results will among others demonstrate that the difficulty of the posed problem is highly dependent upon the composition of the constitutive properties of the material candidates....

  18. Under-reporting of accidents involving biological material by nursing professionals at a Brazilian emergency hospital.

    Science.gov (United States)

    Facchin, Luiza Tayar; Gir, Elucir; Pazin-Filho, Antonio; Hayashida, Miyeko; da Silva Canini, Silvia Rita Marin

    2013-01-01

    Pathogens can be transmitted to health professionals after contact with biological material. The exact number of infections deriving from these events is still unknown, due to the lack of systematic surveillance data and under-reporting. A cross-sectional study was carried out, involving 451 nursing professionals from a Brazilian tertiary emergency hospital between April and July 2009. Through an active search, cases of under-reporting of occupational accidents with biological material by the nursing team were identified by means of individual interviews. The Institutional Review Board approved the research project. Over half of the professionals (237) had been victims of one or more accidents (425 in total) involving biological material, and 23.76% of the accidents had not been officially reported using an occupational accident report. Among the underreported accidents, 53.47% were percutaneous and 67.33% were bloodborne. The main reason for nonreporting was that the accident had been considered low risk. The under-reporting rate (23.76%) was low in comparison with other studies, but most cases of exposure were high risk.

  19. Manual work in cold environments and its impact on selection of materials for protective gloves based on workplace observations.

    Science.gov (United States)

    Irzmańska, Emilia; Wójcik, Paulina; Adamus-Włodarczyk, Agnieszka

    2018-04-01

    This article presents a workplace observations on manual work in cold environments and its impact on the selection of materials for protective gloves. The workplace observations was conducted on 107 workers in 7 companies and involved measurements of the temperature of air and objects in the workplaces; in addition the type of surface and shape of the objects was determined. Laboratory tests were also carried out on 11 materials for protective gloves to be used in cold environments. Protective characteristics, including mechanical properties (wear, cut, tear, and puncture resistance), insulation properties (thermal resistance), functional parameters, and hygienic properties (resistance to surface wetting, material stiffness) were evaluated. Appropriate levels of performance and quality, corresponding to the protective and functional properties of the materials, were determined. Based on the results of manual work and laboratory tests, directions for the selection of materials for the construction of protective gloves were formulated with a view to improving work ergonomics. Copyright © 2017 Elsevier Ltd. All rights reserved.

  20. Status of transport events involving radioactive materials which occurred in France between 1999 and 2011

    International Nuclear Information System (INIS)

    2013-01-01

    This report presents transport events involving radioactive materials, occurred on French territory from 1999 to 2011, listed in the IRSN's database. 1,304 events have been recorded. For each of them, many parameters have been collected and analysed from information listed in the notifications and reports of the events sent by users (type of event, purpose, package design, level on the INES scale...). The numbers of events notified in 2010 and 2011 are slightly higher than the average of 100 events per year. The two main causes of notification concern documentation errors (in transport documents or labeling) and handling mishaps. The downward trend of frequency of package or conveyance contaminations has been confirmed. A short description of the outstanding events occurred in 2010 and 2011 is proposed. This synthesis also gives an outline of the actions recommended by IRSN to avoid recurrence of the notified events and improve the safety of the transports of radioactive materials

  1. Assessment of events involving transport of radioactive materials in France, 1999-2011

    International Nuclear Information System (INIS)

    2013-01-01

    This report presents transport events involving radioactive materials that occurred in France from 1999 to 2011 and entered in the IRSN's database. For each of the 1,304 events recorded, many parameters have been collected and analysed from information listed in the declarations and reports of events sent by users (type of event, purpose, package design, INES level, etc.). The number of events declared in 2010 and 2011 is slightly higher than the average of 100 events per year. The two main reasons for declaration concern errors in transport documentation or labelling and handling mishaps. The new data confirm the downward trend in frequency of package and vehicle contaminations. A short description of outstanding events in 2010 and 2011 is included. This assessment also gives an outline of the actions recommended by IRSN to avoid recurrence of declared events and improve the safety of radioactive material transport. (authors)

  2. Development of supporting system for emergency response to maritime transport accidents involving radioactive material

    International Nuclear Information System (INIS)

    Odano, N.; Matsuoka, T.; Suzuki, H.

    2004-01-01

    National Maritime Research Institute has developed a supporting system for emergency response of competent authority to maritime transport accidents involving radioactive material. The supporting system for emergency response has functions of radiation shielding calculation, marine diffusion simulation, air diffusion simulation and radiological impact evaluation to grasp potential hazard of radiation. Loss of shielding performance accident and loss of sealing ability accident were postulated and impact of the accidents was evaluated based on the postulated accident scenario. Procedures for responding to emergency were examined by the present simulation results

  3. Surface Characteristics and Biofilm Development on Selected Dental Ceramic Materials

    Directory of Open Access Journals (Sweden)

    Kyoung H. Kim

    2017-01-01

    Full Text Available Background. Intraoral adjustment and polishing of dental ceramics often affect their surface characteristics, promoting increased roughness and consequent biofilm growth. This study correlated surface roughness to biofilm development with four commercially available ceramic materials. Methods. Four ceramic materials (Vita Enamic®, Lava™ Ultimate, Vitablocs Mark II, and Wieland Reflex® were prepared as per manufacturer instructions. Seventeen specimens of each material were adjusted and polished to simulate clinical intraoral procedures and another seventeen remained unaltered. Specimens were analysed by SEM imaging, confocal microscopy, and crystal violet assay. Results. SEM images showed more irregular surface topography in adjusted specimens than their respective controls. Surface roughness (Ra values were greater in all materials following adjustments. All adjusted materials with the exception of Vitablocs Mark II promoted significantly greater biofilm growth relative to controls. Conclusion. Simulated intraoral polishing methods resulted in greater surface roughness and increased biofilm accumulation.

  4. Design of lightweight multi-material automotive bodies using new material performance indices of thin-walled beams for the material selection with crashworthiness consideration

    International Nuclear Information System (INIS)

    Cui, Xintao; Zhang, Hongwei; Wang, Shuxin; Zhang, Lianhong; Ko, Jeonghan

    2011-01-01

    Currently, automotive bodies are constructed usually using a single material, e.g. steel or aluminum. Compared to single-material automotive bodies, multi-material automotive bodies allow optimal material selection in each structural component for higher product performance and lower cost. This paper presents novel material performance indices and procedures developed to guide systematic material selection for multi-material automotive bodies. These new indices enable to characterize the crashworthiness performance of complex-shaped thin-walled beams in multi-material automotive bodies according to material types. This paper also illustrates the application of these performance indices and procedures by designing a lightweight multi-material automotive body. These procedures will help to design a lightweight and affordable body favored by the automotive industry, thus to reduce fuel consumption and greenhouse gas emissions.

  5. Experience in the analysis of accidents and incidents involving the transport of radioactive materials

    International Nuclear Information System (INIS)

    Warner-Jones, S.M.; Hughes, J.S.; Shaw, K.B.

    2002-01-01

    Some half a million packages containing radioactive materials are transported to, from and within the UK annually. Accidents and incidents involving these shipments are rare. However, there is always the potential for such an event, which could lead to a release of the contents of a package or an increase in radiation level caused by damaged shielding. These events could result in radiological consequences for transport workers. As transport occurs in the public environment, such events could also lead to radiation exposures of members of the public. The UK Department for Transport (DfT), together with the Health and Safety Executive (HSE) have supported, for almost 20 years, work to compile, analyse and report on accidents and incidents that occur during the transport of radioactive materials. Annual reports on these events have been produced for twelve years. The details of these events are recorded in the Radioactive Materials Transport Event Database (RAMTED) maintained by the National Radiological Protection Board on behalf of the DfT and HSE. Information on accidents and incidents dates back to 1958. RAMTED currently includes information of 708 accidents and incidents, covering the period 1958 to 2000. This paper presents a summary of the data covering this period, identifying trends and lessons learned together with a discussion of some examples. It was found that, historically, the most significant exposures were received as a result of accidents involving the transport of industrial radiography sources. However, the frequency and severity of these events has decreased considerably in the later years of this study due to improvements in training, awareness and equipment. The International Atomic Energy Agency and the Nuclear Energy Agency, have established the international nuclear event scale (INES), which is described in detail in a users' guide. The INES has been revised to fully include transport events, and the information in RAMTED has been reviewed

  6. An Integrated Model of Material Supplier Selection and Order Allocation Using Fuzzy Extended AHP and Multiobjective Programming

    Directory of Open Access Journals (Sweden)

    Zhi Li

    2013-01-01

    Full Text Available This paper presents a supplier selection and order allocation (SSOA model to solve the problem of a multiperiod supplier selection and then order allocation in the environment of short product life cycle and frequent material purchasing, for example, fast fashion environment in apparel industry. At the first stage, with consideration of multiple decision criteria and the fuzziness of the data involved in deciding the preferences of multiple decision variables in supplier selection, the fuzzy extent analytic hierarchy process (FEAHP is adopted. In the second stage, supplier ranks are inputted into an order allocation model that aims at minimizing the risk of material purchasing and minimizing the total material purchasing costs using a dynamic programming approach, subject to constraints on deterministic customer demand and deterministic supplier capacity. Numerical examples are presented, and computational results are reported.

  7. Emergency communication and information issues in terrorist events involving radioactive materials.

    Science.gov (United States)

    Becker, Steven M

    2004-01-01

    With the threat posed by terrorism involving radioactive materials now high on the nation's agenda, local, state, and federal agencies are moving to enhance preparedness and response capabilities. Crucial to these efforts is the development of effective risk communication strategies. This article reports findings from an ongoing study of risk communication issues in nuclear/radiological terrorism situations. It is part of a larger CDC-funded effort that aims to better understand communication challenges associated with weapons of mass destruction terrorism incidents. Presented here are formative research findings from 16 focus groups (n = 163) in which a multi-part, hypothetical radioactive materials terrorism situation was discussed. Twelve of the focus groups were carried out with members of the general public (drawn from a variety of ethnic backgrounds and geographic locations), and four groups were composed of first responders, hospital emergency department personnel, and public health professionals. One aim of the focus groups was to elicit detailed information on people's knowledge, views, perceptions, reactions, and concerns related to a nuclear/radiological terrorism event, and to better understand people's specific information needs and preferred information sources. A second aim was to pretest draft informational materials prepared by CDC and NIOSH. Key findings for the public and professional groups are presented, and the implications of the research for developing messages in radiological/nuclear terrorism situations are explored.

  8. On the use of the HOTSPOT code for evaluating accidents involving radioactive materials

    International Nuclear Information System (INIS)

    Sattinger, D.; Sarussi, R.; Tzarfati, Y.; Levinson, S.; Tshuva, A.

    2004-01-01

    The HOTSPOT Health Physics code was created by LLNL in order to provide Health Physics personnel with a fast, field portable calculation tool for evaluating accidents involving radioactive materials. The HOTSPOT code is a first order approximation of the radiation effects associated with the atmospheric release of radioactive materials. HOTSPOT programs are reasonably accurate for a timely initial assessment. More importantly, HOTSPOT code produce a consistent output for the same input assumptions, and minimize the probability of errors associated with reading a graph incorrectly. Four general programs, Plume, Explosion, Fire, and Resuspension, calculate a downwind assessment following the release of radioactive material resulting from a continuous or puff release, explosive release, fuel or fire, or an area contamination event. Additional programs estimate the dose commitment from inhalation of any one of the radionuclides listed in the database of radionuclides, calibrate a radiation survey instrument for ground survey measurements, and screening of alpha emitters in the Lung. We believe that the HOTSPOT code is extremely valuable in providing reasonable and reliable guidance for a diversity of application. For example, we demonstrate the release of 241 Am(20Ci) to the atmosphere

  9. Assessment of the radiological impact of selected building materials

    International Nuclear Information System (INIS)

    Gwiazdowski, B.

    1983-02-01

    Naturally occurring radionuclides in building materials are a source of external and internal radiation exposure to essentially the entire Polish population. The programme of our studies met two main aspects on radioactivity of building materials: Gamma dose rate and radon or alpha potential energy concentration measurements in dwellings of various kinds of structure and materials in both industrial and rural districts of Poland. Gamma dose rate measurements were made in about 2200 dwellings and radon or alpha potential energy concentration measurements - in 750 dwellings. On the basis of these studies the annual effective dose equivalent to the Polish population due to gamma and alpha radiation indoors was estimated to be 0.39 mSv/a and 0.99 mSv/a, respectively. The contribution of external (from gamma) and internal (from alpha) radiation exposure due to naturally occurring radionuclides in building materials to the total radiation exposure of Polish population was assessed to be 3.6 per cent and 34.2 per cent, respectively. Measurements of about 1500 samples of various kinds of building materials and raw materials were made to determine radionuclide concentrations in them. The highest values were obtained in samples of phosphogypsum, fly ash and slag: potassium concentration ranges up to 36 pCi g -1 (a slag sample), radium - up to 17 pCi g -1 (a phosphogypsum sample) and thorium - up to 4 pCi g -1 (a phosphogypsum). On the basis of the results of our studies we came to the conclusion that it was necessary to work out a control system which could protect habitants against enhancement of indoor exposure to ionizing radiation

  10. Towards 'selection rules' in the radiation chemistry of molecular materials

    International Nuclear Information System (INIS)

    Feldman, V.I.; Inst. of Synthetic Polymetric Materials, Moscow; Moscow State Univ.

    2002-01-01

    Complete text of publication follows. There are a lot of experimental evidences suggesting that the primary radiation-induced events in organic solids and polymers are highly selective and sensitive to conformation, molecular packing, matrix environment, etc. Nevertheless, specific 'selection rules' in the radiation chemistry of molecules in solids are still not established. This contribution presents a review of our recent studies of the radiation damage in organic molecules in low-temperature matrices and polymers aimed at elucidation of basic physical factors controlling selectivity of the primary chemical events. The following aspects will be analyzed: 1. 'Fine tuning' effects in positive hole trapping in rigid systems containing molecular 'traps' with close ionization energy. 2. Selective chemical bond weakening in ionized molecules: experimental and theoretical results. 3. Matrix-assisted and matrix-controlled chemical reactions of ionized molecules in solid media (including the effect of 'matrix-catalysis'). 4. Effect of excess energy on the fate of ionized molecules in solid matrices: the role of intramolecular and intermolecular relaxation. Finally, the problem of experimental and theoretical simulation of the distribution of the radiation-induced events in complex molecular systems and polymers will be addressed

  11. Use of selected waste materials in concrete mixes.

    Science.gov (United States)

    Batayneh, Malek; Marie, Iqbal; Asi, Ibrahim

    2007-01-01

    A modern lifestyle, alongside the advancement of technology has led to an increase in the amount and type of waste being generated, leading to a waste disposal crisis. This study tackles the problem of the waste that is generated from construction fields, such as demolished concrete, glass, and plastic. In order to dispose of or at least reduce the accumulation of certain kinds of waste, it has been suggested to reuse some of these waste materials to substitute a percentage of the primary materials used in the ordinary portland cement concrete (OPC). The waste materials considered to be recycled in this study consist of glass, plastics, and demolished concrete. Such recycling not only helps conserve natural resources, but also helps solve a growing waste disposal crisis. Ground plastics and glass were used to replace up to 20% of fine aggregates in concrete mixes, while crushed concrete was used to replace up to 20% of coarse aggregates. To evaluate these replacements on the properties of the OPC mixes, a number of laboratory tests were carried out. These tests included workability, unit weight, compressive strength, flexural strength, and indirect tensile strength (splitting). The main findings of this investigation revealed that the three types of waste materials could be reused successfully as partial substitutes for sand or coarse aggregates in concrete mixtures.

  12. Use of selected waste materials in concrete mixes

    International Nuclear Information System (INIS)

    Batayneh, Malek; Marie, Iqbal; Asi, Ibrahim

    2007-01-01

    A modern lifestyle, alongside the advancement of technology has led to an increase in the amount and type of waste being generated, leading to a waste disposal crisis. This study tackles the problem of the waste that is generated from construction fields, such as demolished concrete, glass, and plastic. In order to dispose of or at least reduce the accumulation of certain kinds of waste, it has been suggested to reuse some of these waste materials to substitute a percentage of the primary materials used in the ordinary portland cement concrete (OPC). The waste materials considered to be recycled in this study consist of glass, plastics, and demolished concrete. Such recycling not only helps conserve natural resources, but also helps solve a growing waste disposal crisis. Ground plastics and glass were used to replace up to 20% of fine aggregates in concrete mixes, while crushed concrete was used to replace up to 20% of coarse aggregates. To evaluate these replacements on the properties of the OPC mixes, a number of laboratory tests were carried out. These tests included workability, unit weight, compressive strength, flexural strength, and indirect tensile strength (splitting). The main findings of this investigation revealed that the three types of waste materials could be reused successfully as partial substitutes for sand or coarse aggregates in concrete mixtures

  13. Inkjet Printing of Functional Materials on Selectively Plasma Treated Surfaces

    NARCIS (Netherlands)

    ir Martijn van Dongen; ir Renee Verkuijlen; Dr Jan Bernards

    2011-01-01

    In manufacturing of organic electronics, inkjet printing as an alternative technique for depositing materials is becoming increasingly important. Aside to the ink formulations challenges, improving the resolution of the printed patterns is a major goal. In this study we will discuss a newly

  14. Recycling of Metals and Materials: A Selected Bibliography.

    Science.gov (United States)

    Seidman, Ruth K., Comp.; Castrow, Lee, Comp.

    Recycling of metals and materials has as its purpose the easing of two major environmental crises. First, we re-utilize scarce and non-renewable resources. Second, solid waste disposal problems can be alleviated. Industry has long been concerned with reclaiming its own waste products, and is now beginning to respond to the need for dealing with…

  15. Combined Influence of Selective Focus and Decision Involvement on Attitude-Decision Consistency in a Memory-based Decision Context

    OpenAIRE

    A. VAN KERCKHOVE; I. VERMEIR; M. GEUENS

    2009-01-01

    Marketers often use salient stimuli to draw consumers’ attention to a specific brand in the hope that a selective focus on the own brand increases the sales of this brand. However, previous studies are inconsistent concerning the impact that selectively focusing on a specific brand has on final brand choice. To offer an explanation for these inconsistent results, this paper introduces decision involvement as a moderator of the relation between selective focus and attitude-decision consistency...

  16. Study of the exposures received by the persons involved in the transportation of radioactive materials

    International Nuclear Information System (INIS)

    Hamard, J.; Sousselier, Y.

    1983-01-01

    An important step in the optimization process applied to exposures in the field of the transport of radioactive materials is an accurate inventory of the exposures actually received by the workers. The results of this study underlines that nearly all the doses received are well below the threshold values for the classification of the workers as occasionally exposed and a fortiori as professionally exposed and consequently no personal monitoring should be necessary for them. Thus the inventory of exposures is somewhat difficult as the workers implied in the transport process are not classified as exposed workers and not subject to personnal or collective dosimetry. Therefore a good knowledge of the exposures received during the transport of irradiated fuels should require a systematic follow up of this kind of transport all along their route including a careful dosimetric monitoring of the workers taking part in the transport. On the other hand, the reduction of the doses obtained by increasing the mechanization involves very high monetary costs as compared to the reduction of the detriment. Perhaps a more important reduction of the exposures could be attained by a better protection in the cars or lorries used for the transport of categories A and B packages. But it seems that in the case of the transports, the optimization is applied mainly during the conception and the testing of the packages and only little progress will be possible without involving disproportionated monetary costs. 4 references, 10 tables

  17. Nanostructured materials for selective recognition and targeted drug delivery

    International Nuclear Information System (INIS)

    Kotrotsiou, O; Kotti, K; Dini, E; Kammona, O; Kiparissides, C

    2005-01-01

    Selective recognition requires the introduction of a molecular memory into a polymer matrix in order to make it capable of rebinding an analyte with a very high specificity. In addition, targeted drug delivery requires drug-loaded vesicles which preferentially localize to the sites of injury and avoid uptake into uninvolved tissues. The rapid evolution of nanotechnology is aiming to fulfill the goal of selective recognition and optimal drug delivery through the development of molecularly imprinted polymeric (MIP) nanoparticles, tailor-made for a diverse range of analytes (e.g., pharmaceuticals, pesticides, amino acids, etc.) and of nanostructured targeted drug carriers (e.g., liposomes and micelles) with increased circulation lifetimes. In the present study, PLGA microparticles containing multilamellar vesicles (MLVs), and MIP nanoparticles were synthesized to be employed as drug carriers and synthetic receptors respectively

  18. Experimental Observations on Dynamic Response of Selected Transparent Armor Materials

    Science.gov (United States)

    2014-07-01

    Monolithic single crystal sapphire plates (100×100× 10 mm), from GT Crystal Systems, Inc., Salem , MA, in crystallographically controlled directions...Future Army Applications (2011) The National Academies Press , Washington, D.C. 5. Graff KF (1991) Wave motion in elastic solids, Dover Publications 6...2004) Visualization of impact damage in ceramics using the edge-on impact technique. Int J Appl Ceram Technol 1 (3):235–242 Fig. 38 Selection of a

  19. Improving the sun drying of apricots (Prunus armeniaca) with photo-selective dryer cabinet materials

    Science.gov (United States)

    Photo-selective materials have been studied for their effects on the pre-harvest quality of horticultural crops, but little work has been done on potential post-harvest effects. The aim of this work was to characterize the effects of 5 different photo-selective acrylic materials (used as the lid to...

  20. Optimal selection for shielding materials by fuzzy linear programming

    International Nuclear Information System (INIS)

    Kanai, Y.; Miura, N.; Sugasawa, S.

    1996-01-01

    An application of fuzzy linear programming methods to optimization of a radiation shield is presented. The main purpose of the present study is the choice of materials and the search of the ratio of mixture-component as the first stage of the methodology on optimum shielding design according to individual requirements of nuclear reactor, reprocessing facility, shipping cask installing spent fuel, ect. The characteristic values for the shield optimization may be considered their cost, spatial space, weight and some shielding qualities such as activation rate and total dose rate for neutron and gamma ray (includes secondary gamma ray). This new approach can reduce huge combination calculations for conventional two-valued logic approaches to representative single shielding calculation by group-wised optimization parameters determined in advance. Using the fuzzy linear programming method, possibilities for reducing radiation effects attainable in optimal compositions hydrated, lead- and boron-contained materials are investigated

  1. Pelamis WEC - main body structural design and materials selection

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, C.

    2003-07-01

    This report summarises the results of a study evaluating the potential use of rolled steel, glass reinforced plastic, wood-epoxy laminate, and different forms of concrete as primary structural materials for the Pelamis Wave Energy Converter (WEC) as part of a strategy to refine the design by highlighting cost savings for long-term manufacture. Details are given of the drawing up of a load spectrum in order to assess the candidate structures, the choice of glass reinforced plastic, concrete, and steel for further evaluation based on preliminary screening, the assessment of the material requirements for each candidate structure, and cost estimates. The advantages of the use of concrete are discussed and recommendations are presented.

  2. Analysis on tank truck accidents involved in road hazardous materials transportation in china.

    Science.gov (United States)

    Shen, Xiaoyan; Yan, Ying; Li, Xiaonan; Xie, Chenjiang; Wang, Lihua

    2014-01-01

    Due to the sheer size and capacity of the tanker and the properties of cargo transported in the tank, hazmat tanker accidents are more disastrous than other types of vehicle accidents. The aim of this study was to provide a current survey on the situation of accidents involving tankers transporting hazardous materials in China. Detailed descriptions of 708 tanker accidents associated with hazmat transportation in China from 2004 to 2011 were analyzed to identify causes, location, types, time of occurrence, hazard class for materials involved, consequences, and the corresponding probability. Hazmat tanker accidents mainly occurred in eastern (38.1%) and southwest China (12.3%). The most frequent hazmat tanker accidents involved classes 2, 3, and 8. The predominant accident types were rollover (29.10%), run-off-the-road (16.67%), and rear-end collisions (13.28%), with a high likelihood of a large spill occurring. About 55.93% of the accidents occurred on freeways and class 1 roads, with the spill percentage reaching 75.00% and the proportion of spills that occurred in the total accidents amounting to 77.82%, of which 61.72% are considered large spills. The month with the highest accident probability was July (12.29%), and most crashes occurred during the early morning (4:00-6:00 a.m.) and midday (10:00 a.m.-12:00 p.m.) hours, 19.63% versus 16.10%. Human-related errors (73.8%) and vehicle-related defects (19.6%) were the primary reasons for hazmat tanker crashes. The most common outcomes of a hazmat tanker accident was a spill without further events (55.51%), followed by a release with fire (7.77%), and release with an explosion (2.54%). The safety situation of China's hazmat tanker transportation is grim. Such accidents not only have high spill percentages and consistently large spills but they can also cause serious consequences, such as fires and explosions. Improving the training of drivers and the quality of vehicles, deploying roll stability aids, enhancing

  3. Corrosion behavior of materials selected for FMIT lithium system

    International Nuclear Information System (INIS)

    Bazinet, G.D.; Down, M.G.; Matlock, D.K.

    1983-01-01

    The corrosion program consisted of a multi-disciplinary approach utilizing the liquid lithium test resources and capabilities of several laboratories. Specific concerns associated with the overall objective of materials corrosion behavior were evaluated at each laboratory. Testing conditions included: approx. 3700 hours of exposure to flowing lithium at temperatures from 230 0 C to 270 0 C and approx. 6500 hours of exposure to flowing lithium at an isothermal temperature of 270 0 C. Principal areas of investigation, to be discussed here briefly, included lithium corrosion effects on the following: (1) types 304 and 304L austenitic stainless steels, which are specified as reference materials for the FMIT lithium system; (2) type 304 stainless steel weldments (w/type 308 stainless steel filler) typical of specified tube and butt welds in the lithium system design; (3) titanium, zirconium and yttrium, which represent potential hot trap getter materials; (4) BNi4 braze alloy, used as a potential attachement method in the plug/seat fabrication of liquid lithium valves; and (5) type 321 stainless steel bellows, typical of bellows used in potential liquid lithium valve designs

  4. Corrosion behavior of materials selected for FMIT lithium system

    Energy Technology Data Exchange (ETDEWEB)

    Bazinet, G.D.; Down, M.G.; Matlock, D.K.

    1983-01-01

    The corrosion program consisted of a multi-disciplinary approach utilizing the liquid lithium test resources and capabilities of several laboratories. Specific concerns associated with the overall objective of materials corrosion behavior were evaluated at each laboratory. Testing conditions included: approx. 3700 hours of exposure to flowing lithium at temperatures from 230/sup 0/C to 270/sup 0/C and approx. 6500 hours of exposure to flowing lithium at an isothermal temperature of 270/sup 0/C. Principal areas of investigation, to be discussed here briefly, included lithium corrosion effects on the following: (1) types 304 and 304L austenitic stainless steels, which are specified as reference materials for the FMIT lithium system; (2) type 304 stainless steel weldments (w/type 308 stainless steel filler) typical of specified tube and butt welds in the lithium system design; (3) titanium, zirconium and yttrium, which represent potential hot trap getter materials; (4) BNi4 braze alloy, used as a potential attachement method in the plug/seat fabrication of liquid lithium valves; and (5) type 321 stainless steel bellows, typical of bellows used in potential liquid lithium valve designs.

  5. Study on Material Selection of Reactor Pressure Vessel of SCWR

    Science.gov (United States)

    Ma, Shuli; Luo, Ying; Yin, Qinwei; Li, Changxiang; Xie, Guofu

    This paper first analyzes the feasibility of SA-508 Grade 3 Class 1 Steel as an alternative material for Supercritical Water-Cooled Reactor (SCWR) Reactor Pressure Vessel (RPV). This kind of steel is limited to be applied in SCWR RPV due to its quenching property, though large forging could be accomplished by domestic manufacturers in forging aspect. Therefore, steels with higher strength and better quenching property are needed for SWCR RPV. The chemical component of SA-508 Gr.3 Cl.2 steel is similar to that of SA-508 Gr.3 Cl.1 steel, and more appropriate matching of strength and toughness could be achieved by the adjusting the elements contents, as well as proper control of tempering temperature and time. In light of the fact that Cl.2 steel has been successfully applied to steam generator, it could be an alternative material for SWCR RPV. SA-508 Gr.4N steel with high strength and good toughness is another alternative material for SCWR RPV. But large amount of research work before application is still needed for the lack of data on welding and irradiation etc.

  6. Preliminary selection criteria for the Yucca Mountain Project waste package container material

    International Nuclear Information System (INIS)

    Halsey, W.G.

    1991-01-01

    The Department of Energy's Yucca Mountain Project (YMP) is evaluating a site at Yucca Mountain in Nevada for construction of a geologic repository for the storage of high-level nuclear waste. Lawrence Livermore National Laboratory's (LLNL) Nuclear Waste Management Project (NWMP) has the responsibility for design, testing, and performance analysis of the waste packages. The design is performed in an iterative manner in three sequential phases (conceptual design, advanced conceptual design, and license application design). An important input to the start of the advanced conceptual design is the selection of the material for the waste containers. The container material is referred to as the 'metal barrier' portion of the waste package, and is the responsibility of the Metal Barrier Selection and Testing task at LLNL. The selection will consist of several steps. First, preliminary, material-independent selection criteria will be established based on the performance goals for the container. Second, a variety of engineering materials will be evaluated against these criteria in a screening process to identify candidate materials. Third, information will be obtained on the performance of the candidate materials, and final selection criteria and quantitative weighting factors will be established based on the waste package design requirements. Finally, the candidate materials will be ranked against these criteria to determine whether they meet the mandated performance requirements, and to provide a comparative score to choose the material for advanced conceptual design activities. This document sets forth the preliminary container material selection criteria to be used in screening candidate materials. 5 refs

  7. Next Generation Nuclear Plant Materials Selection and Qualification Program Plan

    Energy Technology Data Exchange (ETDEWEB)

    R. Doug Hamelin; G. O. Hayner

    2004-11-01

    The U.S. Department of Energy (DOE) has selected the Very High Temperature Reactor (VHTR) design for the Next Generation Nuclear Plant (NGNP) Project. The NGNP will demonstrate the use of nuclear power for electricity and hydrogen production without greenhouse gas emissions. The reactor design is a graphite-moderated, helium-cooled, prismatic or pebble bed thermal neutron spectrum reactor with an average reactor outlet temperature of at least 1000 C. The NGNP will use very high burn up, lowenriched uranium, TRISO-Coated fuel in a once-through fuel cycle. The design service life of the NGNP is 60 years.

  8. Materials Selection and Their Characteristics as Used in Rapid Prototyping

    Science.gov (United States)

    Cooper, K.; Salvail, P.; Vesely, E.; Wells, D.

    1999-01-01

    NASA's Marshall Space Flight Center (MSFC) conducted a program to evaluate six technologies used in Rapid Prototyping (RP) to produce investment casting patterns. In this paper, RP refers to the collective additive fabrication technologies known as Solid Free-Form Fabrication. Such technologies are being used with increasing frequency in manufacturing applications, due in part to their rapidly expanding capabilities to fabricate models from many types of materials. This study used ABS plastic, polycarbonate, TrueForm PM6, epoxy resin, paper, starch, and wax. The baseline model was a semi-complex prototype fuel pump housing, intended for use in the X-33 reusable launch vehicle. All models were shelled in a production- grade colloidal silica ceramic. Primary coats were zircon-base flour with zircon backup, while secondary coats were silica grains with a tabular alumina backup. Each model was shelled in an identical manner, using the same atmospheric conditions and drying times, as well as the same number of layers. Bake-outs and firing cycles were consistent with the leach ability of each material. Preheat and bath temperatures were also kept consistent. All molds were cast in vacuum using a hydrogen-resistant superalloy (NASA- 23) that was developed in-house. The final technical evaluation included detailed measurements of the model and the final casting, in order to determine any dimensional changes caused by different pattern materials, as well as documentation of all defects and any obvious refractory/model reactions. Prototype production costs were estimated for each method and taken into consideration during trade-off analysis.

  9. Improved selectivity towards NO₂ of phthalocyanine-based chemosensors by means of original indigo/nanocarbons hybrid material.

    Science.gov (United States)

    Brunet, J; Pauly, A; Dubois, M; Rodriguez-Mendez, M L; Ndiaye, A L; Varenne, C; Guérin, K

    2014-09-01

    A new and original gas sensor-system dedicated to the selective monitoring of nitrogen dioxide in air and in the presence of ozone, has been successfully achieved. Because of its high sensitivity and its partial selectivity towards oxidizing pollutants (nitrogen dioxide and ozone), copper phthalocyanine-based chemoresistors are relevant. The selectivity towards nitrogen dioxide results from the implementation of a high efficient and selective ozone filter upstream the sensing device. Thus, a powdered indigo/nanocarbons hybrid material has been developed and investigated for such an application. If nanocarbonaceous material acts as a highly permeable matrix with a high specific surface area, immobilized indigo nanoparticles are involved into an ozonolysis reaction with ozone leading to the selective removal of this analytes from air sample. The filtering yields towards each gas have been experimentally quantified and establish the complete removal of ozone while having the concentration of nitrogen dioxide unchanged. Long-term gas exposures reveal the higher durability of hybrid material as compared to nanocarbons and indigo separately. Synthesis, characterizations by many complementary techniques and tests of hybrid filters are detailed. Results on sensor-system including CuPc-based chemoresistors and indigo/carbon nanotubes hybrid material as in-line filter are illustrated. Sensing performances will be especially discussed. Copyright © 2014 Elsevier B.V. All rights reserved.

  10. Materials selection in micromechanical design: an application of the Ashby approach

    OpenAIRE

    Srikar, V.T.; Spearing, S.M.

    2003-01-01

    The set of materials available to microsystems designers is rapidly expanding. Techniques now exist to introduce and integrate a large number of metals, alloys, ceramics, glasses, polymers, and elastomers into microsystems, motivating the need for a rational approach for materials selection in microsystems design. As a step toward such an approach, we focus on the initial stages of materials selection for micromechanical structures with minimum feature sizes greater than 1 /spl mu/m. The vari...

  11. An overview of safety and environmental considerations in the selection of materials for fusion facilities

    International Nuclear Information System (INIS)

    Petti, D.A.; Piet, S.J.; Seki, Y.

    1996-01-01

    Safety and environmental considerations can play a large role in the selection of fusion materials. In this paper, we review the attributes of different structural, plasma facing, and breeding materials from a safety perspective and discuss some generic waste management issues as they relate to fusion materials in general. Specific safety concerns exist for each material that must be dealt with in fusion facility design. Low activation materials offer inherent safety benefits compared with conventional materials, but more work is needed before these materials have the requisite certified databases. In the interim, the international thermonuclear experimental reactor (ITER) has selected more conventional materials and is showing that the safety concerns with these materials can be addressed by proper attention to design. In the area of waste management disposal criteria differ by country. However, the criteria are all very strict making disposal of fusion components difficult. As a result, recycling has gained increasing attention. (orig.)

  12. Synthesis and Purification of Iodoaziridines Involving Quantitative Selection of the Optimal Stationary Phase for Chromatography

    Science.gov (United States)

    Boultwood, Tom; Affron, Dominic P.; Bull, James A.

    2014-01-01

    The highly diastereoselective preparation of cis-N-Ts-iodoaziridines through reaction of diiodomethyllithium with N-Ts aldimines is described. Diiodomethyllithium is prepared by the deprotonation of diiodomethane with LiHMDS, in a THF/diethyl ether mixture, at -78 °Cin the dark. These conditions are essential for the stability of the LiCHI2 reagent generated. The subsequent dropwise addition of N-Ts aldimines to the preformed diiodomethyllithium solution affords an amino-diiodide intermediate, which is not isolated. Rapid warming of the reaction mixture to 0 °C promotes cyclization to afford iodoaziridines with exclusive cis-diastereoselectivity. The addition and cyclization stages of the reaction are mediated in one reaction flask by careful temperature control. Due to the sensitivity of the iodoaziridines to purification, assessment of suitable methods of purification is required. A protocol to assess the stability of sensitive compounds to stationary phases for column chromatography is described. This method is suitable to apply to new iodoaziridines, or other potentially sensitive novel compounds. Consequently this method may find application in range of synthetic projects. The procedure involves firstly the assessment of the reaction yield, prior to purification, by 1H NMR spectroscopy with comparison to an internal standard. Portions of impure product mixture are then exposed to slurries of various stationary phases appropriate for chromatography, in a solvent system suitable as the eluent in flash chromatography. After stirring for 30 min to mimic chromatography, followed by filtering, the samples are analyzed by 1H NMR spectroscopy. Calculated yields for each stationary phase are then compared to that initially obtained from the crude reaction mixture. The results obtained provide a quantitative assessment of the stability of the compound to the different stationary phases; hence the optimal can be selected. The choice of basic alumina, modified to

  13. New membrane materials for potassium-selective ion-sensitive field-effect transistors

    NARCIS (Netherlands)

    van der Wal, P.D.; van der Wal, Peter D.; Skowronska-Ptasinska, Maria; van den Berg, Albert; Bergveld, Piet; Sudholter, Ernst; Sudholter, Ernst J.R.; Reinhoudt, David

    1990-01-01

    Several polymeric materials were studied as membrane materials for potassium-selective ion-sensitive field-effect transistors (ISFETs) to overcome the problems related with the use of conventional plasticized poly(vinyl chloride) membranes casted on ISFET gate surfaces. Several acrylate materials,

  14. Radiographic implications of procedures involving cardiac implantable electronic devices (CIEDs – Selected aspects

    Directory of Open Access Journals (Sweden)

    Roman Steckiewicz

    2017-06-01

    Full Text Available Background: Some cardiac implantable electronic device (CIED implantation procedures require the use of X-rays, which is reflected by such parameters as total fluoroscopy time (TFT and dose-area product (DAP – defined as the absorbed dose multiplied by the area irradiated. Material and Methods: This retrospective study evaluated 522 CIED implantation (424 de novo and 98 device upgrade and new lead placement procedures in 176 women and 346 men (mean age 75±11 years over the period 2012–2015. The recorded procedure-related parameters TFT and DAP were evaluated in the subgroups specified below. The group of 424 de novo procedures included 203 pacemaker (PM and 171 implantable cardioverter-defibrillator (ICD implantation procedures, separately stratified by single-chamber and dual-chamber systems. Another subgroup of de novo procedures involved 50 cardiac resynchronization therapy (CRT devices. The evaluated parameters in the group of 98 upgrade procedures were compared between 2 subgroups: CRT only and combined PM and ICD implantation procedures. Results: We observed differences in TFT and DAP values between procedure types, with PM-related procedures showing the lowest, ICD – intermediate (with values for single-chamber considerably lower than those for dual-chamber systems and CRT implantation procedures – highest X-ray exposure. Upgrades to CRT were associated with 4 times higher TFT and DAP values in comparison to those during other upgrade procedures. Cardiac resynchronization therapy de novo implantation procedures and upgrades to CRT showed similar mean values of these evaluated parameters. Conclusions: Total fluoroscopy time and DAP values correlated progressively with CIED implantation procedure complexity, with CRT-related procedures showing the highest values of both parameters. Med Pr 2017;68(3:363–374

  15. Communication of work accidents involving biological material: a study in the city of Santa Cruz do Sul/RS

    OpenAIRE

    Dayane Diehl; Karini da Rosa; Susimar Souza Rosa; Susane Beatriz Frantz Krug

    2012-01-01

    Rationale and Objectives: Healthcare workers are constantly exposed to the risk of occupational accidents involving biological material. Thus the aim of the study was to develop a profile of workers involved in workplace accidents with biological materials in Santa Cruz do Sul, through the number of notifications made in information systems. Methods: Transversal retrospective study with a quantitative approach; data collection was carried out between the years 2008 and 2010 from medical recor...

  16. Status of international collaborative efforts on selected ITER materials

    International Nuclear Information System (INIS)

    Belyakov, V.A.; Fabritsiev, S.A.; Mazul, I.V.; Rowcliffe, A.F.

    2000-01-01

    The paper presents an overview of the performance of refractory metals, beryllium, and copper alloys, for the international thermonuclear experimental reactor (ITER) high heat flux structures. High temperature brazing, hot isostatic pressing (HIP), friction welding, explosive bonding, and other methods were explored to join copper alloys to 316 stainless steel for first wall and limiter applications. It is concluded that the main material problems for the ITER high heat flux components are: (a) degradation of properties after the manufacturing cycle (especially for Be/Cu and Cu/stainless steel (SS) joints); (b) helium embrittlement of Be, and Cu, and; (c) radiation-induced loss of fracture toughness for Be, W, and Cu alloys

  17. Decommissioning Strategies Selection for Facilities Using Radioactive Material

    International Nuclear Information System (INIS)

    Husen Zamroni; Jaka Rachmadetin

    2008-01-01

    The facilities using radioactive material that have been stopped operation will require some form of the decommissioning for public and environment safety. The approaches are identified by three decommissioning strategies: immediate dismantling, deferred dismantling and entombment. If a facility undergoes immediate dismantling, most radio nuclides will have no such sufficient time to decay and therefore this strategy may not provide reduction in the worker exposure. A facility that undergoes deferred dismantling may advantage from the radioactive decay of residual radio nuclides during the long term storage period and entombment could be a viable option for other nuclear facilities containing only short lived or limited concentrations of long lived radionuclides. Mostly, only two types of the decommissioning used to be done in the world, immediate and deferred dismantling. (author)

  18. Selection of Corrosion Resistant Materials for Nuclear Waste Repositories

    International Nuclear Information System (INIS)

    R.B. Rebak

    2006-01-01

    Several countries are considering geological repositories to dispose of nuclear waste. The environment of most of the currently considered repositories will be reducing in nature, except for the repository in the US, which is going to be oxidizing. For the reducing repositories, alloys such as carbon steel, stainless steels and titanium are being evaluated. For the repository in the US, some of the most corrosion resistant commercially available alloys are being investigated. This paper presents a summary of the behavior of the different materials under consideration for the repositories and the current understanding of the degradation modes of the proposed alloys in ground water environments from the point of view of general corrosion, localized corrosion and environmentally assisted cracking

  19. Updating Classifications of Ceramic Dental Materials: A Guide to Material Selection.

    Science.gov (United States)

    McLaren, Edward A; Figueira, Johan

    2015-06-01

    The indications for and composition of today's dental ceramic materials serve as the basis for determining the appropriate class of ceramics to use for a given case. By understanding the classifications, composition, and characteristics of the latest all-ceramic materials, which are presented in this article in order of most to least conservative, dentists and laboratory technicians can best determine the ideal material for a particular treatment.

  20. Application of GRA for Sustainable Material Selection and Evaluation Using LCA

    Science.gov (United States)

    Jayakrishna, Kandasamy; Vinodh, Sekar; Sakthi Sanghvi, Vijayaselvan; Deepika, Chinadurai

    2016-07-01

    Material selection is identified as a successful key parameter in establishing any product to be sustainable, considering its end of life (EoL) characteristics. An accurate understanding of expected service conditions and environmental considerations are crucial in the selection of material plays a vital role with overwhelming customer expectations and stringent laws. Therefore, this article presents an integrated approach for sustainable material selection using grey relational analysis (GRA) considering the EoL disposal strategies with respect to an automotive product. GRA, an impact evaluation model measures the degree of similarity between the comparability (choice of material) sequence and reference (EoL strategies) sequence based on the relational grade. The ranking result shows that the outranking relationships in the order, ABS-REC > PP-INC > AL-REM > PP-LND > ABS-LND > ABS-INC > PU-LND > AL-REC > AL-LND > PU-INC > AL-INC. The best sustainable material selected was ABS and recycling was selected as the best EoL strategy with the grey relational value of 2.43856. The best material selected by this approach, ABS was evaluated for its viability using life cycle assessment and the estimated impacts also proved the practicability of the selected material highlighting the focus on dehumidification step in the manufacturing of the case product using this developed multi-criteria approach.

  1. Tunable Impedance Spectroscopy Sensors via Selective Nanoporous Materials.

    Energy Technology Data Exchange (ETDEWEB)

    Nenoff, Tina M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Small, Leo J [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-09-01

    Impedance spectroscopy was leveraged to directly detect the sorption of I 2 by selective adsorption into nanoporous metal organic frameworks (MOF). Films of three different types of MOF frameworks, respectively, were drop cast onto platinum interdigitated electrodes, dried, and exposed to gaseous I 2 at 25, 40, or 70 C. The MOF frameworks varied in topology from small pores (equivalent to I 2 diameter) to large pore frameworks. The combination of the chemistry of the framework and pore size dictated quantity and kinetics of I 2 adsorption. Air, argon, methanol, and water were found to produce minimal changes in ZIF-8 impedance. Independent of MOF framework characteristics, all resultant sensors showed high response to I 2 in air. As an example of sensor output, I 2 was readily detected at 25 C in air within 720 s of exposure, using an un-optimized sensor geometry with a small pored MOF. Further optimization of sensor geometry, decreasing MOF film thicknesses and maximizing sensor capacitance, will enable faster detection of trace I 2 .

  2. Production of Biofuels from Selected Cellulosic Waste materials

    Directory of Open Access Journals (Sweden)

    Jathwa Abdul Kareem Ibrahim

    2017-08-01

    Full Text Available In this study four types of cellulose-rich municipal solid wastes (residuals of orange, banana peel, corn residues, and saw dust were used as raw materials. These cellulosic substrates usually have a lot of lignin content which prevents the process of saccharification by microorganisms. Thus pretreatment methods of enzymatic, acid or base with enzymatic treatment and dilute acid followed by autoclaving were necessary to dignify these wastes and to obtain higher reducing sugar yields and hence higher ethanol production. Dilute HCl acid of 1% followed by autoclaving at 121℃ for 30 min proved to give good result where significant amounts of reducing sugars were obtained at the end of the saccharification process. Orange peel proved to give the highest glucose concentration of an average of 6000 mg/l on day 4 of the saccharification process. Fermentation was carried out for the hydrolyzed samples using Saccharomyces cerevisiae yeast. The amount of ethanol produced after fermentation was found to be the highest for orange peel having a value of 1300 mg/l after 96h of incubation. As science is proceeding, engineered microorganisms could help to produce sustainable fuels from cellulose-rich municipal solid wastes in the future.

  3. Characterization of hydrotalcite materials for CO2 selective membranes

    Energy Technology Data Exchange (ETDEWEB)

    Feuillade, V.C.; Haije, W.G. [ECN Hydrogen and Clean Fossil Fuels, Petten (Netherlands)

    2006-07-15

    The present concern about climate change has urged researchers and engineers all over the world to go and look for ways of reducing greenhouse gas emissions. Largescale CO2 emissions occur at power plants burning fossil fuels or e.g. the production of hydrogen from carbonaceous feed. In these cases pre- or post-combustion CO2 capture techniques followed by CO2 storage seems a promising route for reducing emissions. Prerequisite in these processes is the effective separation of CO2 from mixed gaseous process streams. The purpose of this work is to develop CO2 membranes to allow for the combination of natural gas reforming with separation of H2 and CO2 in separation enhanced reactors, i.e. membrane reactors, for carbon-free hydrogen production or electricity generation. This paper describes the materials' properties of hydrotalcites, a promising class of compounds for CO2 membranes. They have already proven their applicability as CO2 sorbent in sorption enhanced reaction processes. It is of fundamental importance to know the structural stability of this compound in the operational window of a chosen membrane reactor prior to any membrane fabrication. To this end, in-situ XRPD and DRIFTS as well as TGA-MS and SEM-EDX measurements have been performed on commercial (Pural) and hydrothermally synthesized homemade samples.

  4. Liquid metal batteries - materials selection and fluid dynamics

    Science.gov (United States)

    Weier, T.; Bund, A.; El-Mofid, W.; Horstmann, G. M.; Lalau, C.-C.; Landgraf, S.; Nimtz, M.; Starace, M.; Stefani, F.; Weber, N.

    2017-07-01

    Liquid metal batteries are possible candidates for massive and economically feasible large-scale stationary storage and as such could be key components of future energy systems based mainly or exclusively on intermittent renewable electricity sources. The completely liquid interior of liquid metal batteries and the high current densities give rise to a multitude of fluid flow phenomena that will primarily influence the operation of future large cells, but might be important for today’s smaller cells as well. The paper at hand starts with a discussion of the relative merits of using molten salts or ionic liquids as electrolytes for liquid metal cells and touches the choice of electrode materials. This excursus into electrochemistry is followed by an overview of investigations on magnetohydrodynamic instabilities in liquid metal batteries, namely the Tayler instability and electromagnetically excited gravity waves. A section on electro-vortex flows complements the discussion of flow phenomena. Focus of the flow related investigations lies on the integrity of the electrolyte layer and related critical parameters.

  5. Charged particle and laser irradiation of selected materials

    International Nuclear Information System (INIS)

    Svendsen, W.E.

    1996-11-01

    The main topics of the present thesis are the processes governing electronic sputtering of insulators and laser ablation of metals and insulators. The sputtering yield for electron bombardment of solid deuterium was investigated using quartz crystal microbalances as the measuring technique. The sputtering yield was measured with varying electron energy and deuterium film thickness. Laser ablation measurements of silver and nickel were carried out using a Nd:YAG laser. The effect of various experimental parameters such as background gas pressure (Ar, N 2 ), position of quartz crystals with respect to target position and the optimal number of laser shots for carrying out the experiments were investigated. The deposition rate was measured with varying laser wavelength and laser fluence. The angular distribution of the ablated material was measured for silver as well. A theoretical model based on the thermal properties of laser interaction with metals was applied in the initial phase of ablation. For the non-thermal processes governing laser interaction with the ablated plasma plume, a model developed by Phipps and Dreyfus was used to interpret the results. Laser ablation measurements of water-ice were carried using a Nitrogen laser. Attempts were made to measure the deposition rate for various the laser wavelengths and energies. (au) 8 tabs., 49 ills., 77 refs

  6. Review of selected dynamic material control functions for international safeguards

    International Nuclear Information System (INIS)

    Lowry, L.L.

    1980-09-01

    With the development of Dynamic Special Nuclear Material Accounting and Control systems used in nuclear manufacturing and reprocessing plants, there arises the question as to how these systems affect the IAEA inspection capabilities. The systems in being and under development provide information and control for a variety of purposes important to the plant operator, the safeguards purpose being one of them. This report attempts to judge the usefulness of these dynamic systems to the IAEA and have defined 12 functions that provide essential information to it. If the information acquired by these dynamic systems is to be useful to the IAEA, the inspectors must be able to independently verify it. Some suggestions are made as to how this might be done. But, even if it should not be possible to verify all the data, the availability to the IAEA of detailed, simultaneous, and plant-wide information would tend to inhibit a plant operator from attempting to generate a floating or fictitious inventory. Suggestions are made that might be helpful in the design of future software systems, an area which has proved to be fatally deficient in some systems and difficult in all

  7. Charged particle and laser irradiation of selected materials

    Energy Technology Data Exchange (ETDEWEB)

    Svendsen, W E

    1996-11-01

    The main topics of the present thesis are the processes governing electronic sputtering of insulators and laser ablation of metals and insulators. The sputtering yield for electron bombardment of solid deuterium was investigated using quartz crystal microbalances as the measuring technique. The sputtering yield was measured with varying electron energy and deuterium film thickness. Laser ablation measurements of silver and nickel were carried out using a Nd:YAG laser. The effect of various experimental parameters such as background gas pressure (Ar, N{sub 2}), position of quartz crystals with respect to target position and the optimal number of laser shots for carrying out the experiments were investigated. The deposition rate was measured with varying laser wavelength and laser fluence. The angular distribution of the ablated material was measured for silver as well. A theoretical model based on the thermal properties of laser interaction with metals was applied in the initial phase of ablation. For the non-thermal processes governing laser interaction with the ablated plasma plume, a model developed by Phipps and Dreyfus was used to interpret the results. Laser ablation measurements of water-ice were carried using a Nitrogen laser. Attempts were made to measure the deposition rate for various the laser wavelengths and energies. (au) 8 tabs., 49 ills., 77 refs.

  8. Lesions to polar/orbital prefrontal cortex selectively impair reasoning about emotional material.

    Science.gov (United States)

    Goel, Vinod; Lam, Elaine; Smith, Kathleen W; Goel, Amit; Raymont, Vanessa; Krueger, Frank; Grafman, Jordan

    2017-05-01

    While it is widely accepted that lesions to orbital prefrontal cortex lead to emotion related disruptions and poor decision-making, there is very little patient data on this issue involving actual logical reasoning tasks. We tested patients with circumscribed, focal lesions largely confined to polar/orbital prefrontal cortex (BA 10 & 11) (N=17) on logical reasoning tasks involving neutral and emotional content, and compared their performance to that of an age and education-matched normal control group (N=22) and a posterior lesion control group (N=24). Our results revealed a significant group by content interaction driven by a selective impairment in the polar/orbital prefrontal cortex group compared to healthy normal controls and to the parietal patient group, in the emotional content reasoning trials. Subsequent analyses of congruent and incongruent reasoning trials indicated that this impairment was driven by the poor performance of patients with polar/orbital lesions in the incongruent trials. We conclude that the polar/orbital prefrontal cortex plays a critical role in filtering emotionally charged content from the material before it is passed on to the reasoning system in lateral/dorsal regions of prefrontal cortex. Where unfiltered content is passed to the reasoning engine, either as a result of pathology (as in the case of our patients) or as a result of individual differences, reasoning performance suffers. Copyright © 2017 Elsevier Ltd. All rights reserved.

  9. Method for selecting raw materials to preparing ceramic masses: application to raw material for red ceramic

    International Nuclear Information System (INIS)

    Moreno, Maria Margarita Torres; Rocha, Rogers Raphael da; Zanard, Antenor

    2012-01-01

    We studied the raw materials used in a factory building blocks, located in Cesario Lange city (SP). It extracts raw materials from various sources in the region to make the dough. The mixtures were prepared from dry milled powders based on data related to the plasticity of the raw materials. It was obtained with the apparatus Vicat-cone in order to obtain similar levels of water absorption of the samples burned at 900 deg C for all compositions. To quantify the proportion of each clay was used the Lever Rule. In this firing temperature, where sintering is mainly by diffusion from a solid state, different compositions of the same set of four raw materials resulted in similar values. (author)

  10. An Augmented Common Weight Data Envelopment Analysis for Material Selection in High-tech Industries

    Directory of Open Access Journals (Sweden)

    Iman Shokr

    2016-08-01

    Full Text Available Material selection is a challenging issue in manufacturing processes while the inappropriate selected material may lead to fail the manufacturing process or end user experience especially in high-tech industries such as aircraft and shipping. Every material has different quantitative and qualitative criteria which should be considered simultaneously when assessing and selecting the right material. A weighted linear optimization method (WLOM in the class of data envelopment analysis which exists in literature is adopted to address material selection problem while accounting for both qualitative and quantitative criteria. However, it is demonstrated the adopted WLOM method is not able to produce a full ranking vector for the material selection problems borrowed from the literature. Thus, an augmented common weight data envelopment analysis model (ACWDEA is developed in this paper with the aim of eliminating deficiencies of WLOM model. The proposed ACWDEA is able to produce full ranking vector in decision making problems with less computational complexities in superior to the WLOM. Two material selection problems are solved and results are compared with WLOM and previous methods. Finally, the robustness and effectiveness of the proposed ACWDEA method are evaluated through Spearman’s correlation tests.

  11. Materials selection as an interdisciplinary technical activity: basic methodology and case studies

    Directory of Open Access Journals (Sweden)

    M. Ferrante

    2000-04-01

    Full Text Available The technical activity known as Materials Selection is reviewed in its concepts and methodologies. Objectives and strategies are briefly presented and two important features are introduced and discussed; (i Merit Indices: a combination of materials properties, which maximises the objectives chosen by the designer and (ii Materials Properties Maps: a bi-dimensional space whose coordinates are pairs of properties in which materials can be plotted and compared directly in terms of their merit indices. A general strategy for the deduction of these indices is explained and a formal methodology to establish a ranking of candidate materials when multiple constraints intervene is presented. Finally, two case studies are discussed in depth, one related to materials substitution in the context of mechanical design and a less conventional case linking material selection to physical comfort in the home furniture industry.

  12. Application of multi-criteria material selection techniques to constituent refinement in biobased composites

    International Nuclear Information System (INIS)

    Miller, Sabbie A.; Lepech, Michael D.; Billington, Sarah L.

    2013-01-01

    Highlights: • Biobased composites have the potential to replace certain engineered materials. • Woven reinforcement can provide better material properties in biobased composites. • Short fiber filler can provide lower environmental impact in biobased composites. • Per function, different fibers are desired to lower composite environmental impact. - Abstract: Biobased composites offer a potentially low environmental impact material option for the construction industries. Designing these materials to meet both performance requirements for an application and minimize environmental impacts requires the ability to refine composite constituents based on environmental impact and mechanical properties. In this research, biobased composites with varying natural fiber reinforcement in a poly(β-hydroxybutyrate)-co-(β-hydroxyvalerate) matrix were characterized based on material properties through experiments and environmental impact through life cycle assessments. Using experimental results, these biobased composites were found to have competitive flexural properties and thermal conductivity with certain short-chopped glass fiber reinforced plastics. Multi-criteria material selection techniques were applied to weigh desired material properties with greenhouse gas emissions, fossil fuel demand, and Eco-Indicator ’99 score. The effects of using different reinforcing fibers in biobased composites were analyzed using the developed selection scheme as a tool for choosing constituents. The use of multi-criteria material selection provided the ability to select fiber reinforcement for biobased composites and showed when it would be more appropriate to use a novel biobased composite or a currently available engineered material

  13. Readability in reading materials selection and coursebook design for college English in China

    OpenAIRE

    Lu, Zhongshe

    2002-01-01

    This thesis studies the application of readability in reading materials selection and coursebook design for college English in an EFL context in China. Its aim is to develop rationales which coursebook writers can utilise in selecting materials as texts and as a basis for designing tasks. This study, through a combination of quantitative and qualitative research methods, argues that readability is applicable in the EFL Chinese context, and readability plays a important role in determining...

  14. Unveiling of novel regio-selective fatty acid double bond hydratases from Lactobacillus acidophilus involved in the selective oxyfunctionalization of mono- and di-hydroxy fatty acids.

    Science.gov (United States)

    Kim, Kyoung-Rok; Oh, Hye-Jin; Park, Chul-Soon; Hong, Seung-Hye; Park, Ji-Young; Oh, Deok-Kun

    2015-11-01

    The aim of this study is the first time demonstration of cis-12 regio-selective linoleate double-bond hydratase. Hydroxylation of fatty acids, abundant feedstock in nature, is an emerging alternative route for many petroleum replaceable products thorough hydroxy fatty acids, carboxylic acids, and lactones. However, chemical route for selective hydroxylation is still quite challenging owing to low selectivity and many environmental concerns. Hydroxylation of fatty acids by hydroxy fatty acid forming enzymes is an important route for selective biocatalytic oxyfunctionalization of fatty acids. Therefore, novel fatty acid hydroxylation enzymes should be discovered. The two hydratase genes of Lactobacillus acidophilus were identified by genomic analysis, and the expressed two recombinant hydratases were identified as cis-9 and cis-12 double-bond selective linoleate hydratases by in vitro functional validation, including the identification of products and the determination of regio-selectivity, substrate specificity, and kinetic parameters. The two different linoleate hydratases were the involved enzymes in the 10,13-dihydroxyoctadecanoic acid biosynthesis. Linoleate 13-hydratase (LHT-13) selectively converted 10 mM linoleic acid to 13S-hydroxy-9(Z)-octadecenoic acid with high titer (8.1 mM) and yield (81%). Our study will expand knowledge for microbial fatty acid-hydroxylation enzymes and facilitate the designed production of the regio-selective hydroxy fatty acids for useful chemicals from polyunsaturated fatty acid feedstocks. © 2015 Wiley Periodicals, Inc.

  15. The incidence of parametrial tumor involvement in select patients with early cervix cancer is too low to justify parametrectomy

    NARCIS (Netherlands)

    Stegeman, M.; Louwen, M.; van der Velden, J.; ten Kate, F. J. W.; den Bakker, M. A.; Burger, C. W.; Ansink, A. C.

    2007-01-01

    OBJECTIVE: To determine the incidence of parametrial involvement in a select group of patients with early cervical cancer. METHODS: We retrospectively reviewed the records of patients with cervical cancer and a maximum tumor diameter of 2 cm, infiltration depth <10 mm and negative pelvic lymph nodes

  16. Integrated shape and material selection for single and multi-performance criteria

    International Nuclear Information System (INIS)

    Singh, Jasveer; Mirjalili, Vahid; Pasini, Damiano

    2011-01-01

    Research highlights: → The method of shape transformers is extended to torsional stiffness and combined load design. → The method is generalized for multi-criteria selection of shape and material. → Performance charts are presented for single and multi-objective selection of cross-section shape and material. → A four quadrant performance chart is presented to visualize the relation between objective function space and design variable space. -- Abstract: A shape and material selection method, based on the concept of shape transformers, has been recently introduced to characterize the mass efficiency of lightweight beams under bending and shear. This paper extends this method to deal with the case of torsional stiffness design, and generalize it to single and multi-crieria selection of lightweight shafts subjected to a combination of bending, shear, and torsional load. The novel feature of the paper is the useful integration of shape and material to model and visualize multi-objective selection problems. The scheme is centered on concept selection in structural design, and hinges on measures that govern the shape properties of a cross-section regardless of its size. These measures, referred as shape transformers, can classify shapes in a way similar to material classification. The procedure is exemplified by considering torsional stiffness as a constraint. The performance charts are developed for single and multi-criteria to visualize in a glance the whole range of cross-sectional shapes for each material. Each design chart is explained with a brief example.

  17. Selecting Materials on the Iranian Revolution: A Short Bibliography of Materials Now in Print.

    Science.gov (United States)

    Sanchez, James Joseph

    Appropriate for adult reading, 27 books published between 1969 and 1982 are listed in this annotated bibliography for those studying the Iranian Revolution. Works are arranged into two categories: (1) "Background Materials: Islam and Petroleum," which lists basic works that make it easier to place events in Iran within an intelligible…

  18. Design and material selection for ITER first wall/blanket, divertor and vacuum vessel

    Energy Technology Data Exchange (ETDEWEB)

    Ioki, K.; Barabash, V.; Cardella, A.; Elio, F.; Gohar, Y.; Janeschitz, G.; Johnson, G.; Kalinin, G.; Lousteau, D.; Onozuka, M.; Parker, R.; Sannazzaro, G.; Tivey, R. [ITER JCT, Garching (Germany)

    1998-10-01

    Design and R and D have progressed on the ITER vacuum vessel, shielding and breeding blankets, and the divertor. The principal materials have been selected and the fabrication methods selected for most of the components based on design and R and D results. The resulting design changes are discussed for each system. (orig.) 11 refs.

  19. Design and material selection for ITER first wall/blanket, divertor and vacuum vessel

    Science.gov (United States)

    Ioki, K.; Barabash, V.; Cardella, A.; Elio, F.; Gohar, Y.; Janeschitz, G.; Johnson, G.; Kalinin, G.; Lousteau, D.; Onozuka, M.; Parker, R.; Sannazzaro, G.; Tivey, R.

    1998-10-01

    Design and R&D have progressed on the ITER vacuum vessel, shielding and breeding blankets, and the divertor. The principal materials have been selected and the fabrication methods selected for most of the components based on design and R&D results. The resulting design changes are discussed for each system.

  20. Zirconium-modified materials for selective adsorption and removal of aqueous arsenic

    Science.gov (United States)

    Zhao, Hongting; Moore, Robert C.

    2004-11-30

    A method, composition, and apparatus for removing contaminant species from an aqueous medium comprising: providing a material to which zirconium has been added, the material selected from one or more of zeolites, cation-exchangeable clay minerals, fly ash, mesostructured materials, activated carbons, cellulose acetate, and like porous and/or fibrous materials; and contacting the aqueous medium with the material to which zirconium has been added. The invention operates on all arsenic species in the form of arsenate, arsenite and organometallic arsenic, with no pretreatment necessary (e.g., oxidative conversion of arsenite to arsenate).

  1. Selective memory retrieval of auditory what and auditory where involves the ventrolateral prefrontal cortex.

    Science.gov (United States)

    Kostopoulos, Penelope; Petrides, Michael

    2016-02-16

    There is evidence from the visual, verbal, and tactile memory domains that the midventrolateral prefrontal cortex plays a critical role in the top-down modulation of activity within posterior cortical areas for the selective retrieval of specific aspects of a memorized experience, a functional process often referred to as active controlled retrieval. In the present functional neuroimaging study, we explore the neural bases of active retrieval for auditory nonverbal information, about which almost nothing is known. Human participants were scanned with functional magnetic resonance imaging (fMRI) in a task in which they were presented with short melodies from different locations in a simulated virtual acoustic environment within the scanner and were then instructed to retrieve selectively either the particular melody presented or its location. There were significant activity increases specifically within the midventrolateral prefrontal region during the selective retrieval of nonverbal auditory information. During the selective retrieval of information from auditory memory, the right midventrolateral prefrontal region increased its interaction with the auditory temporal region and the inferior parietal lobule in the right hemisphere. These findings provide evidence that the midventrolateral prefrontal cortical region interacts with specific posterior cortical areas in the human cerebral cortex for the selective retrieval of object and location features of an auditory memory experience.

  2. Factors involved in the selection of limestone reagents for use in wet FGD systems

    International Nuclear Information System (INIS)

    Jarvis, J.B.; Roothaan, E.S.; Meserole, F.B.; Owens, D.R.

    1992-01-01

    With recent activity in the design and construction of retrofit flue gas desulfurization (FGD) systems, many utilities are faced with the task of selecting limestones which will allow FGD systems to function as designed, and at the same time, provide cost-effective operation. The Electric Power Research Institute (EPRI) has sponsored research to identify factors which should be considered in the reagent selection process. A set of capabilities has been developed which is currently being employed to assist six utilities in selecting cost-effective reagent sources. The major elements in the selection package consist of an analytical characterization of candidate limestones; grindability, reactivity, and magnesium availability testing; and performance modeling utilizing EPRI's FGD PRocess Integration and Simulation Model (FGDPRISM). The results from these measurements are used to perform a site-specific economic analysis which can be used to rank the candidate limestones and quantify the impact of various limestone properties on plant operating costs. This paper includes a description of each element in the selection package along with a review of current research activities aimed at improving predictions of limestone reactivity and magnesium availability. An example is presented which illustrates how reactivity and magnesium availability affect both the performance of an FGD system and plant operating costs

  3. Selected Bibliography of Egyptian Educational Materials, Vol. 1, No. 3, 1975.

    Science.gov (United States)

    Al-Ahram Center for Scientific Translations, Cairo (Egypt).

    There are 101 selected entries in this annotated bibliography of Egyptian materials on education published in 1975. Materials include journal articles, books, and government documents. The bibliography covers the following topics: academic certificates and dissertations, art education, audiovisual aids, camps, civics curricula, conferences and…

  4. Selected Bibliography of Egyptian Educational Materials, Vol. 3, No. 1, 1977.

    Science.gov (United States)

    Al-Ahram Center for Scientific Translations, Cairo (Egypt).

    This annotated bibliography lists 135 selected educational materials from Egypt covering the period 1976-1977. The materials are drawn from a variety of Egyptian newspapers, journals, government publications, and university research reports. The entries are organized into 55 categories, including Adolescence; Adult Education; Art Education; Basic…

  5. Selected Bibliography of Egyptian Educational Materials, Vol. 1, No. 2, 1975.

    Science.gov (United States)

    Al-Ahram Center for Scientific Translations, Cairo (Egypt).

    There are 108 selected entries in this annotated bibliography of Egyptian materials on education published in 1975. Materials include journal articles, books, and government documents. The bibliography covers the following topics: adolescence, art education, child upbringing, comprehensive schools, curricula, educational change, educational aids,…

  6. Selected Bibliography of Egyptian Educational Materials, Vol. 3, No. 2, 1977.

    Science.gov (United States)

    Al-Ahram Center for Scientific Translations, Cairo (Egypt).

    The annotated bibliography identifies 134 selected educational materials from Egypt published during 1977. The materials are drawn from Egyptian newspapers, journals, government publications, and university research reports. The entries are organized into 54 categories, including Art Education, Arabic Language, Commercial Schools, Curricula,…

  7. Materials Down Select Decisions Made Within the Department of Energy Hydrogen Sorption Center of Excellence

    Energy Technology Data Exchange (ETDEWEB)

    Simpson, Lin [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2009-11-30

    Technical report describing DOE's Hydrogen Sorption Center of Excellence investigation into various adsorbent and chemisorption materials and progress towards meeting DOE's hydrogen storage targets. The report presents a review of the material status as related to DOE hydrogen storage targets and explains the basis for the down select decisions.

  8. Materials design considerations and selection for a large rad waste incinerator

    International Nuclear Information System (INIS)

    Vormelker, P.R.; Jenkins, C.F.; Burns, H.H.

    1997-01-01

    A new incinerator has been built to process self-generated, low level radioactive wastes at the Department of Energy's Savannah River Site. Wastes include protective clothing and other solid materials used during the handling of radioactive materials, and liquid chemical wastes resulting from chemical and waste management operations. The basic design and materials of construction selected to solve the anticipated corrosion problems from hot acidic gases are reviewed. Problems surfacing during trial runs prior to radioactive operations are discussed

  9. Assessment and selection of materials for ITER in-vessel components

    Science.gov (United States)

    Kalinin, G.; Barabash, V.; Cardella, A.; Dietz, J.; Ioki, K.; Matera, R.; Santoro, R. T.; Tivey, R.; ITER Home Teams

    2000-12-01

    During the international thermonuclear experimental reactor (ITER) engineering design activities (EDA) significant progress has been made in the selection of materials for the in-vessel components of the reactor. This progress is a result of the worldwide collaboration of material scientists and industries which focused their effort on the optimisation of material and component manufacturing and on the investigation of the most critical material properties. Austenitic stainless steels 316L(N)-IG and 316L, nickel-based alloys Inconel 718 and Inconel 625, Ti-6Al-4V alloy and two copper alloys, CuCrZr-IG and CuAl25-IG, have been proposed as reference structural materials, and ferritic steel 430, and austenitic steel 304B7 with the addition of boron have been selected for some specific parts of the ITER in-vessel components. Beryllium, tungsten and carbon fibre composites are considered as plasma facing armour materials. The data base on the properties of all these materials is critically assessed and briefly reviewed in this paper together with the justification of the material selection (e.g., effect of neutron irradiation on the mechanical properties of materials, effect of manufacturing cycle, etc.).

  10. Selective patient and public involvement: The promise and perils of pharmaceutical intervention for autism

    DEFF Research Database (Denmark)

    Russell, Ginny; Starr, Sandy; Rodogno, Raffaele

    2017-01-01

    was to scrutinize patient and public involvement (PPI) by a pan-European biomedical consortium working to develop drugs to treat autism. We aimed to use this as an example to illustrate how PPI has been utilized in biomedical research. Setting, participants and analysis: Two public events, one in the UK and one...

  11. Age and gender differences in mate selection criteria for various involvement levels

    NARCIS (Netherlands)

    Buunk, Abraham (Bram); Dijkstra, Pieternel; Fetchenhauer, D.; Kenrick, D.T.

    The present study investigated mate preferences for five different levels of relationship involvement-marriage, serious relationship, falling in love, casual sex, and sexual fantasies-among individuals of 20, 30, 40, 50, and 60 years of age. Consistent with an evolutionary perspective, men preferred

  12. Selecting Learning Tasks: Effects of Adaptation and Shared Control on Learning Efficiency and Task Involvement

    Science.gov (United States)

    Corbalan, Gemma; Kester, Liesbeth; van Merrienboer, Jeroen J. G.

    2008-01-01

    Complex skill acquisition by performing authentic learning tasks is constrained by limited working memory capacity [Baddeley, A. D. (1992). Working memory. "Science, 255", 556-559]. To prevent cognitive overload, task difficulty and support of each newly selected learning task can be adapted to the learner's competence level and perceived task…

  13. Characterization of Angiotensin II Molecular Determinants Involved in AT1 Receptor Functional Selectivity.

    Science.gov (United States)

    Domazet, Ivana; Holleran, Brian J; Richard, Alexandra; Vandenberghe, Camille; Lavigne, Pierre; Escher, Emanuel; Leduc, Richard; Guillemette, Gaétan

    2015-06-01

    The octapeptide angiotensin II (AngII) exerts a variety of cardiovascular effects through the activation of the AngII type 1 receptor (AT1), a G protein-coupled receptor. The AT1 receptor engages and activates several signaling pathways, including heterotrimeric G proteins Gq and G12, as well as the extracellular signal-regulated kinases (ERK) 1/2 pathway. Additionally, following stimulation, βarrestin is recruited to the AT1 receptor, leading to receptor desensitization. It is increasingly recognized that specific ligands selectively bind and favor the activation of some signaling pathways over others, a concept termed ligand bias or functional selectivity. A better understanding of the molecular basis of functional selectivity may lead to the development of better therapeutics with fewer adverse effects. In the present study, we developed assays allowing the measurement of six different signaling modalities of the AT1 receptor. Using a series of AngII peptide analogs that were modified in positions 1, 4, and 8, we sought to better characterize the molecular determinants of AngII that underlie functional selectivity of the AT1 receptor in human embryonic kidney 293 cells. The results reveal that position 1 of AngII does not confer functional selectivity, whereas position 4 confers a bias toward ERK signaling over Gq signaling, and position 8 confers a bias toward βarrestin recruitment over ERK activation and Gq signaling. Interestingly, the analogs modified in position 8 were also partial agonists of the protein kinase C (PKC)-dependent ERK pathway via atypical PKC isoforms PKCζ and PKCι. Copyright © 2015 by The American Society for Pharmacology and Experimental Therapeutics.

  14. Assessment and Selection of Materials for Melbourne City Council House 2

    Directory of Open Access Journals (Sweden)

    Dominique Hes

    2012-11-01

    Full Text Available This paper highlights the role of material selection in the development and contribution toward environmental excellence in the building project Council House 2 (CH2. The paper focuses on the assessment of material and the strategies used by the design team in CH2to ensure the best environmental result. The paper then goes on to explore in a case study the application of these strategies in the selection and specification of concrete on CH2. The purpose of the paper is to explore the difficulties and rewards of careful research of manufacturers' claims and the relative benefits of different materials. The paper concludes that the process of material selection adopted on this project has increased the education of architects and manufacturers alike as well as being environmentally beneficial.

  15. Multicriteria Decision Analysis of Material Selection of High Energy Performance Residential Building

    Science.gov (United States)

    Čuláková, Monika; Vilčeková, Silvia; Katunská, Jana; Krídlová Burdová, Eva

    2013-11-01

    In world with limited amount of energy sources and with serious environmental pollution, interest in comparing the environmental embodied impacts of buildings using different structure systems and alternative building materials will be increased. This paper shows the significance of life cycle energy and carbon perspective and the material selection in reducing energy consumption and emissions production in the built environment. The study evaluates embodied environmental impacts of nearly zero energy residential structures. The environmental assessment uses framework of LCA within boundary: cradle to gate. Designed alternative scenarios of material compositions are also assessed in terms of energy effectiveness through selected thermal-physical parameters. This study uses multi-criteria decision analysis for making clearer selection between alternative scenarios. The results of MCDA show that alternative E from materials on nature plant base (wood, straw bales, massive wood panel) present possible way to sustainable perspective of nearly zero energy houses in Slovak republic

  16. Decision method for optimal selection of warehouse material handling strategies by production companies

    Science.gov (United States)

    Dobos, P.; Tamás, P.; Illés, B.

    2016-11-01

    Adequate establishment and operation of warehouse logistics determines the companies’ competitiveness significantly because it effects greatly the quality and the selling price of the goods that the production companies produce. In order to implement and manage an adequate warehouse system, adequate warehouse position, stock management model, warehouse technology, motivated work force committed to process improvement and material handling strategy are necessary. In practical life, companies have paid small attantion to select the warehouse strategy properly. Although it has a major influence on the production in the case of material warehouse and on smooth costumer service in the case of finished goods warehouse because this can happen with a huge loss in material handling. Due to the dynamically changing production structure, frequent reorganization of warehouse activities is needed, on what the majority of the companies react basically with no reactions. This work presents a simulation test system frames for eligible warehouse material handling strategy selection and also the decision method for selection.

  17. Facile Selective and Diverse Fabrication of Superhydrophobic, Superoleophobic-Superhydrophilic and Superamphiphobic Materials from Kaolin.

    Science.gov (United States)

    Qu, Mengnan; Ma, Xuerui; He, Jinmei; Feng, Juan; Liu, Shanshan; Yao, Yali; Hou, Lingang; Liu, Xiangrong

    2017-01-11

    As the starting material, kaolin is selectively and diversely fabricated to the superhydrophobic, superoleophobic-superhydrophilic, and superamphiphobic materials, respectively. The wettability of the kaolin surface can be selectively controlled and regulated to different superwetting states by choosing the corresponding modification reagent. The procedure is facile to operate, and no special technique or equipment is required. In addition, the procedure is cost-effective and time-saving and the obtained super-repellent properties are very stable. The X-ray photoelectron spectroscopy analysis demonstrates different changes of kaolin particles surfaces which are responsible for the different super-repellency. The scanning electron microscopy displays geometric micro- and nanometer structures of the obtained three kinds of super-repellent materials. The results show that kaolin has good applications in many kinds of superwetting materials. The method demonstrated in this paper provides a new strategy for regulating and controlling the wettability of solid surfaces selectively, diversely, and comprehensively.

  18. Method of Manufacturing A Porous Polymer Component Involving Use of A Dissolvable, Sacrificial Material

    DEFF Research Database (Denmark)

    2015-01-01

    and thereby the resulting inner structure of the component 1 is arranged in a controlled and reproducible manner. The sacrificial material 2 and possibly also the component material 3 may e.g. be arranged by use of a 3D-printer or manually. The method may e.g. be used to manufacture a three...

  19. Involvement of regulatory T cells and selected cytokines in the pathogenesis of bronchial asthma

    Directory of Open Access Journals (Sweden)

    Monika Zuśka-Prot

    2016-06-01

    Full Text Available Asthma pathogenesis is complex and involves the interplay of many factors and actions. Airway inflammation in allergic asthma is characterized by an exaggerated activation of T helper type 2 cells, IgE production and infiltration and activation of eosinophils. The results of studies conducted in recent years indicate that the deficit of naturally occurring Foxp3+CD25+CD4+ and Foxp3+CD25+CD8+ regulatory T cells and type 1 regulatory T cells plays a pivotal role in the development of this disease. Moreover, numerous studies have provided convincing evidence that a decrease in IL-10 production and an increase in IL-17 production have an important place in the pathophysiology of asthma. TGF-β is another important cytokine involved in this disease. TGF-β has a paradoxical status in relation to asthma pathogenesis because it seems to play a role in both suppressing and promoting asthma development. This review discusses briefly clinical and experimental data concerning the involvement of T regulatory cells and IL-10, IL-17 and TGF-β in the pathogenesis of asthma.

  20. Selection of IFE target materials from a safety and environmental perspective

    Energy Technology Data Exchange (ETDEWEB)

    Latkowski, J.F. E-mail: latkowski1@llnl.gov; Sanz, J.; Reyes, S.; Gomez del Rio, J

    2001-05-21

    Target materials for inertial fusion energy (IFE) power plant designs might be selected for a wide variety of reasons including wall absorption of driver energy, material opacity, cost and ease of fabrication. While each of these issues are of great importance, target materials should also be selected based upon their safety and environmental (S and E) characteristics. The present work focuses on the recycling, waste management and accident dose characteristics of potential target materials. If target materials are recycled so that the quantity is small, isotopic separation may be economically viable. Therefore, calculations have been completed for all stable isotopes for all elements from lithium to polonium. The results of these calculations are used to identify specific isotopes and elements that are most likely to be offensive as well as those most likely to be acceptable in terms of their S and E characteristics.

  1. Selection of IFE target materials from a safety and environmental perspective

    Science.gov (United States)

    Latkowski, J. F.; Sanz, J.; Reyes, S.; Gomez del Rio, J.

    2001-05-01

    Target materials for inertial fusion energy (IFE) power plant designs might be selected for a wide variety of reasons including wall absorption of driver energy, material opacity, cost and ease of fabrication. While each of these issues are of great importance, target materials should also be selected based upon their safety and environmental (S&E) characteristics. The present work focuses on the recycling, waste management and accident dose characteristics of potential target materials. If target materials are recycled so that the quantity is small, isotopic separation may be economically viable. Therefore, calculations have been completed for all stable isotopes for all elements from lithium to polonium. The results of these calculations are used to identify specific isotopes and elements that are most likely to be offensive as well as those most likely to be acceptable in terms of their S&E characteristics.

  2. Materials selection for process equipment in the Hanford waste vitrification plant

    Energy Technology Data Exchange (ETDEWEB)

    Elmore, M R; Jensen, G A

    1991-07-01

    The Hanford Waste Vitrification Plant (HWVP) is being designed to vitrify defense liquid high-level wastes and transuranic wastes stored at Hanford. The HWVP Functional Design Criteria (FDC) requires that materials used for fabrication of remote process equipment and piping in the facility be compatible with the expected waste stream compositions and process conditions. To satisfy FDC requirements, corrosion-resistant materials have been evaluated under simulated HWVP-specific conditions and recommendations have been made for HWVP applications. The materials recommendations provide to the project architect/engineer the best available corrosion rate information for the materials under the expected HWVP process conditions. Existing data and sound engineering judgement must be used and a solid technical basis must be developed to define an approach to selecting suitable construction materials for the HWVP. This report contains the strategy, approach, criteria, and technical basis developed for selecting materials of construction. Based on materials testing specific to HWVP and on related outside testing, this report recommends for constructing specific process equipment and identifies future testing needs to complete verification of the performance of the selected materials. 30 refs., 7 figs., 11 tabs.

  3. Tokamak Physics EXperiment (TPX): Toroidal field magnet design, development and manufacture. SDRL 21, Materials and processes selection. Volume 2

    International Nuclear Information System (INIS)

    Smith, B.R.

    1995-01-01

    This document identifies the candidate materials and manufacturing processes selected for development of the TPX Toroidal Field (TF) Magnet. Supporting rationale and selection criteria are provided for justification and the materials properties database report is included for completeness. Specific properties for each material selection are included in this document

  4. Bioactive treatment promotes osteoblast differentiation on titanium materials fabricated by selective laser melting technology.

    Science.gov (United States)

    Tsukanaka, Masako; Fujibayashi, Shunsuke; Takemoto, Mitsuru; Matsushita, Tomiharu; Kokubo, Tadashi; Nakamura, Takashi; Sasaki, Kiyoyuki; Matsuda, Shuichi

    2016-01-01

    Selective laser melting (SLM) technology is useful for the fabrication of porous titanium implants with complex shapes and structures. The materials fabricated by SLM characteristically have a very rough surface (average surface roughness, Ra=24.58 µm). In this study, we evaluated morphologically and biochemically the specific effects of this very rough surface and the additional effects of a bioactive treatment on osteoblast proliferation and differentiation. Flat-rolled titanium materials (Ra=1.02 µm) were used as the controls. On the treated materials fabricated by SLM, we observed enhanced osteoblast differentiation compared with the flat-rolled materials and the untreated materials fabricated by SLM. No significant differences were observed between the flat-rolled materials and the untreated materials fabricated by SLM in their effects on osteoblast differentiation. We concluded that the very rough surface fabricated by SLM had to undergo a bioactive treatment to obtain a positive effect on osteoblast differentiation.

  5. Development of a material property database on selected ceramic matrix composite materials

    Science.gov (United States)

    Mahanta, Kamala

    1996-01-01

    Ceramic Matrix Composites, with fiber/whisker/particulate reinforcement, possess the attractive properties of ceramics such as high melting temperature, high strength and stiffness at high temperature, low density, excellent environmental resistance, combined with improved toughness and mechanical reliability. These unique properties have made these composites an enabling technology for thermomechanically demanding applications in high temperature, high stress and aggressive environments. On a broader scale, CMC's are anticipated to be applicable in aircraft propulsion, space propulsion, power and structures, in addition to ground based applications. However, it is also true that for any serious commitment of the material toward any of the intended critical thermo-mechanical applications to materialize, vigorous research has to be conducted for a thorough understanding of the mechanical and thermal behavior of CMC's. The high technology of CMC'S is far from being mature. In view of this growing need for CMC data, researchers all over the world have found themselves drawn into the characterization of CMC's such as C/SiC, SiC/SiC, SiC/Al203, SiC/Glass, SiC/C, SiC/Blackglas. A significant amount of data has been generated by the industries, national laboratories and educational institutions in the United States of America. NASA/Marshall Space Flight Center intends to collect the 'pedigreed' CMC data and store those in a CMC database within MAPTIS (Materials and Processes Technical Information System). The task of compilation of the CMC database is a monumental one and requires efforts in various directions. The project started in the form of a summer faculty fellowship in 1994 and has spilled into the months that followed and into the summer faculty fellowship of 1995 and has the prospect of continuing into the future for a healthy growth, which of course depends to a large extent on how fast CMC data are generated. The 10-week long summer fellowship has concentrated

  6. Selection of construction materials for equipment in an experimental reprocessing plant

    International Nuclear Information System (INIS)

    Mizrahi, R.; Cragnolino, G.A.

    1994-01-01

    A review is made of the most significant corrosion problems that may be present in different stages of the process in a spent fuel reprocessing plant. The influence of different variables is analyzed: concentration of nitric acid and other oxidizing species, temperature, etc., in corrosion of materials of most frequent use in pipings and equipment. The materials are austenitic stainless steels and refractory metals, especially zirconium and its alloys. Both general and localized corrosion phenomena are analyzed for these materials. Selection criteria for the use of adequate material in different components of the plant are also discussed. (author). 32 refs., 20 figs., 3 tabs

  7. Urine proteome analysis in Dent's disease shows high selective changes potentially involved in chronic renal damage.

    Science.gov (United States)

    Santucci, Laura; Candiano, Giovanni; Anglani, Franca; Bruschi, Maurizio; Tosetto, Enrica; Cremasco, Daniela; Murer, Luisa; D'Ambrosio, Chiara; Scaloni, Andrea; Petretto, Andrea; Caridi, Gianluca; Rossi, Roberta; Bonanni, Alice; Ghiggeri, Gian Marco

    2016-01-01

    Definition of the urinary protein composition would represent a potential tool for diagnosis in many clinical conditions. The use of new proteomic technologies allows detection of genetic and post-trasductional variants that increase sensitivity of the approach but complicates comparison within a heterogeneous patient population. Overall, this limits research of urinary biomarkers. Studying monogenic diseases are useful models to address this issue since genetic variability is reduced among first- and second-degree relatives of the same family. We applied this concept to Dent's disease, a monogenic condition characterised by low-molecular-weight proteinuria that is inherited following an X-linked trait. Results are presented here on a combined proteomic approach (LC-mass spectrometry, Western blot and zymograms for proteases and inhibitors) to characterise urine proteins in a large family (18 members, 6 hemizygous patients, 6 carrier females, and 6 normals) with Dent's diseases due to the 1070G>T mutation of the CLCN5. Gene ontology analysis on more than 1000 proteins showed that several clusters of proteins characterised urine of affected patients compared to carrier females and normal subjects: proteins involved in extracellular matrix remodelling were the major group. Specific analysis on metalloproteases and their inhibitors underscored unexpected mechanisms potentially involved in renal fibrosis. Studying with new-generation techniques for proteomic analysis of the members of a large family with Dent's disease sharing the same molecular defect allowed highly repetitive results that justify conclusions. Identification in urine of proteins actively involved in interstitial matrix remodelling poses the question of active anti-fibrotic drugs in Dent's patients. Copyright © 2015 Elsevier B.V. All rights reserved.

  8. Two enzymes involved in biosynthesis of the host-selective phytotoxin HC-toxin

    International Nuclear Information System (INIS)

    Walton, J.D.

    1987-01-01

    Cochliobolus carbonum race 1 produces a cyclic tetrapeptide HC-toxin, which is necessary for its exceptional virulence on certain varieties of maize. Previous genetic analysis of HC-toxin production by the fungus has indicated that a single genetic locus controls HC-toxin production. Enzymes involved in the biosynthesis of HC-toxin have been sought by following the precedents established for the biosynthetic enzymes of cyclic peptide antibiotics. Two enzymatic activities from C. carbonum race 1 were found, a D-alanine- and an L-proline-dependent ATP/PP/sub i/ exchange, which by biochemical and genetic criteria were shown to be involved in the biosynthesis of HC-toxin. These two activities were present in all tested race 1 isolates of C. carbonum, which produce HC-toxin, and in none of the tested race 2 and race 3 isolates, which do not produce the toxin. In a genetic cross between two isolates of C. carbonum differing at the tox locus, all tox + progeny had both activities, and all tox - progeny lacked both activities

  9. Transient analysis of a thermal storage unit involving a phase change material

    Science.gov (United States)

    Griggs, E. I.; Pitts, D. R.; Humphries, W. R.

    1974-01-01

    The transient response of a single cell of a typical phase change material type thermal capacitor has been modeled using numerical conductive heat transfer techniques. The cell consists of a base plate, an insulated top, and two vertical walls (fins) forming a two-dimensional cavity filled with a phase change material. Both explicit and implicit numerical formulations are outlined. A mixed explicit-implicit scheme which treats the fin implicity while treating the phase change material explicitly is discussed. A band algorithmic scheme is used to reduce computer storage requirements for the implicit approach while retaining a relatively fine grid. All formulations are presented in dimensionless form thereby enabling application to geometrically similar problems. Typical parametric results are graphically presented for the case of melting with constant heat input to the base of the cell.

  10. Selection of engineering materials for heat exchangers (An expert system approach)

    International Nuclear Information System (INIS)

    Ahmed, K.; Abou-Ali, M.; Bassuni, M.

    1997-01-01

    The materials selection as a part of the design process of the heat exchangers is one of the most important steps in the whole industry. The clear recognition of the service requirements of the different types of the heat exchangers is very important to select the adequate and economic materials to meet such requirements. of course the manufacturer should ensure that failure does not occur in service specially it is one of the main and fetal component of the nuclear reactor, pressurized water type (PWR). It is necessary to know the possible mechanisms of failure. Also the achievement of the materials selection using the expert system approach in the process sequence of heat exchanger manufacturing is introduced. Different parameters and requirements controlling each process and the linkage between these parameters and the final product will be shown. 2 figs., 3 tabs

  11. Selection of replacement material for the failed surface level gauge wire in Hanford waste tanks

    International Nuclear Information System (INIS)

    Anantatmula, R.P.; Pitman, S.G.; Lund, A.L.

    1995-10-01

    Surface level gauges fabricated from AISI Type 316 stainless steel (316) wire failed after only a few weeks of operation in underground storage tanks at the Hanford Site. The wire failure was determined to be due to chloride ion assisted corrosion of the 316 wire. Radiation-induced breakdown of the polyvinyl chloride (PVC) riser liners is suspected to be the primary source of the chloride ions. An extensive literature search followed by expert concurrence was undertaken to select a replacement material for the wire. Platinum (Pt)-20 % Iridium (Ir) alloy was selected as the replacement material from tile candidate materials, P-20% Ir, Pt-1O% Rhodium (Rh), Pt-20%Rh and Hastelloy C-22. The selection was made on the basis of the alloy's immunity towards acidic and basic environments as well as its adequate tensile properties in the fully annealed state

  12. Readout from iconic memory and selective spatial attention involve similar neural processes.

    Science.gov (United States)

    Ruff, Christian C; Kristjánsson, Arni; Driver, Jon

    2007-10-01

    Iconic memory and spatial attention are often considered separately, but they may have functional similarities. Here we provide functional magnetic resonance imaging evidence for some common underlying neural effects. Subjects judged three visual stimuli in one hemifield of a bilateral array comprising six stimuli. The relevant hemifield for partial report was indicated by an auditory cue, administered either before the visual array (precue, spatial attention) or shortly after the array (postcue, iconic memory). Pre- and postcues led to similar activity modulations in lateral occipital cortex contralateral to the cued side. This finding indicates that readout from iconic memory can have some neural effects similar to those of spatial attention. We also found common bilateral activation of a fronto-parietal network for postcue and precue trials. These neuroimaging data suggest that some common neural mechanisms underlie selective spatial attention and readout from iconic memory. Some differences were also found; compared with precues, postcues led to higher activity in the right middle frontal gyrus.

  13. Bilingualism trains specific brain circuits involved in flexible rule selection and application.

    Science.gov (United States)

    Stocco, Andrea; Prat, Chantel S

    2014-10-01

    Bilingual individuals have been shown to outperform monolinguals on a variety of tasks that measure non-linguistic executive functioning, suggesting that some facets of the bilingual experience give rise to generalized improvements in cognitive performance. The current study investigated the hypothesis that such advantage in executive functioning arises from the need to flexibly select and apply rules when speaking multiple languages. Such flexible behavior may strengthen the functioning of the fronto-striatal loops that direct signals to the prefrontal cortex. To test this hypothesis, we compared behavioral and brain data from proficient bilinguals and monolinguals who performed a Rapid Instructed Task Learning paradigm, which requires behaving according to ever-changing rules. Consistent with our hypothesis, bilinguals were faster than monolinguals when executing novel rules, and this improvement was associated with greater modulation of activity in the basal ganglia. The implications of these findings for language and executive function research are discussed herein. Published by Elsevier Inc.

  14. Multiple Evolutionary Selections Involved in Synonymous Codon Usages in the Streptococcus agalactiae Genome.

    Science.gov (United States)

    Ma, Yan-Ping; Ke, Hao; Liang, Zhi-Ling; Liu, Zhen-Xing; Hao, Le; Ma, Jiang-Yao; Li, Yu-Gu

    2016-02-24

    Streptococcus agalactiae is an important human and animal pathogen. To better understand the genetic features and evolution of S. agalactiae, multiple factors influencing synonymous codon usage patterns in S. agalactiae were analyzed in this study. A- and U-ending rich codons were used in S. agalactiae function genes through the overall codon usage analysis, indicating that Adenine (A)/Thymine (T) compositional constraints might contribute an important role to the synonymous codon usage pattern. The GC3% against the effective number of codon (ENC) value suggested that translational selection was the important factor for codon bias in the microorganism. Principal component analysis (PCA) showed that (i) mutational pressure was the most important factor in shaping codon usage of all open reading frames (ORFs) in the S. agalactiae genome; (ii) strand specific mutational bias was not capable of influencing the codon usage bias in the leading and lagging strands; and (iii) gene length was not the important factor in synonymous codon usage pattern in this organism. Additionally, the high correlation between tRNA adaptation index (tAI) value and codon adaptation index (CAI), frequency of optimal codons (Fop) value, reinforced the role of natural selection for efficient translation in S. agalactiae. Comparison of synonymous codon usage pattern between S. agalactiae and susceptible hosts (human and tilapia) showed that synonymous codon usage of S. agalactiae was independent of the synonymous codon usage of susceptible hosts. The study of codon usage in S. agalactiae may provide evidence about the molecular evolution of the bacterium and a greater understanding of evolutionary relationships between S. agalactiae and its hosts.

  15. A historical summary of transportation accidents and incidents involving radioactive materials (1971-1988)

    International Nuclear Information System (INIS)

    Cashwell, C.E.; McClure, J.D.

    1989-01-01

    The Radioactive Materials Incident Report (RMIR) Database is a compilation of transportation events that have occurred during the shipment of radioactive materials. The database was developed in 1971 at the Transportation Technology Center (TTC) at Sandia National Laboratories (SNL) to support its research and development efforts for the US Department of Energy (DOE). Currently, RMIR resides on TRANSNET, an interactive computer network that allows an outside user to access transportation risk and systems analysis models and their associated databases. Within the last few months, the RMIR database has been modified so that the menu-driven format expedites database searches, particularly for the infrequent user

  16. An historical summary of transportation accidents and incidents involving radioactive materials (1971--1988)

    International Nuclear Information System (INIS)

    Cashwell, C.E.; McClure, J.D.

    1989-01-01

    The Radioactive Materials Incident Report (RMIR) Database is a compilation of transportation events that have occurred during the shipment of radioactive materials. The database was developed in 1971 at the Transportation Technology Center (TTC) AT Sandia National Laboratories (SNL) to support its research and development efforts for the US Department of Energy (DOE). Currently RMIR resides on TRANSNET, an interactive computer network that allows an outside user to access transportation risk and systems analysis models and their associated databases. Within the last few months, the RMIR database has been modified so that the menu-driven format expedites database searches, particularly for the infrequent user. 2 refs

  17. Department Involvement in Instructional Materials Development for ODL Study at the Zimbabwe Open University (ZOU)

    Science.gov (United States)

    Tanyanyiwa, Vincent Itai; Mutambanengwe, Betty

    2015-01-01

    The teaching and designing of modules at Zimbabwe Open University (ZOU) is the principal responsibility of a single body of teaching staff, although some authors and content reviewers could be sourced from elsewhere if they are not available in ZOU. This survey, through a case study, examines the involvement of lecturers and staff in the…

  18. Self-assembling block copolymer systems involving competing length scales : A route toward responsive materials

    NARCIS (Netherlands)

    Nap, R; Erukhimovich, [No Value; ten Brinke, G; Erukhimovich, Igor

    2004-01-01

    The phase behavior of block copolymers melts involving competing length scales, i.e., able to microphase separate on two different length scales, is theoretically investigated using a self-consistent field approach. The specific block copolymers studied consist of a linear A-block linked to an

  19. Selection criteria for container materials at the proposed Yucca Mountain high level nuclear waste repository

    International Nuclear Information System (INIS)

    Halsey, W.G.

    1989-11-01

    A geological repository has been proposed for the permanent disposal of the nation's high level nuclear waste at Yucca Mountain in the Nevada desert. The containers for this waste must remain intact for the unprecedented service lifetime of 1000 years. A combination of engineering, regulatory, and licensing requirements complicate the container material selection. In parallel to gathering information regarding the Yucca Mountain service environment and material performance data, a set of selection criteria have been established which compare candidate materials to the performance requirements, and allow a quantitative comparison of candidates. These criteria assign relative weighting to varied topic areas such as mechanical properties, corrosion resistance, fabricability, and cost. Considering the long service life of the waste containers, it is not surprising that the corrosion behavior of the material is a dominant factor. 7 refs

  20. Selection of emitter material for application on a radioisotope thermophotovoltaic (RTPV) power system

    Energy Technology Data Exchange (ETDEWEB)

    Kramer, D.P.; Frohlich, N.D.; Koehler, F.A.; Ruhkamp, J.D.; Miller, R.G.; McDougal, J.R.; Pugh, B.K.; Barklay, C.D.; Howell, E.I. [EGG Mound Applied Technologies Building 88, P.O. Box 3000 Miamisburg, Ohio45343 (United States)

    1997-01-01

    Radioisotope Thermophotovoltaic (RTPV) power systems are being considered for long duration space missions due to their predicted high thermal to electrical conversion efficiencies. One critical aspect of these power systems is the selection of an appropriate emitter material which will efficiently radiate the thermal energy generated by the heat source to the photovoltaics. The photovoltaics are {open_quotes}tuned{close_quotes} to convert the infrared wavelengths radiated by the emitter into electrical energy. The emphasis of this paper is on the selection and optimization of an appropriate emitter material which would meet all of the mission requirements. A Kepner Tregoe analysis was performed in order to rank the various candidate refractory materials in relationship to their physical and chemical properties. The results of the analysis and material recommendations are discussed. {copyright} {ital 1997 American Institute of Physics.}

  1. Material Selection for Dye Sensitized Solar Cells Using Multiple Attribute Decision Making Approach

    Directory of Open Access Journals (Sweden)

    Sarita Baghel

    2014-01-01

    Full Text Available Dye sensitized solar cells (DSCs provide a potential alternative to conventional p-n junction photovoltaic devices. The semiconductor thin film plays a crucial role in the working of DSC. This paper aims at formulating a process for the selection of optimum semiconductor material for nanostructured thin film using multiple attribute decision making (MADM approach. Various possible available semiconducting materials and their properties like band gap, cost, mobility, rate of electron injection, and static dielectric constant are considered and MADM technique is applied to select the best suited material. It was found that, out of all possible candidates, titanium dioxide (TiO2 is the best semiconductor material for application in DSC. It was observed that the proposed results are in good agreement with the experimental findings.

  2. State perspective on how clean is clean enough when radioactive materials are involved

    International Nuclear Information System (INIS)

    Bailey, E.D.

    1992-01-01

    The question of how much radioactive material can be left behind by a user of radioactive materials or how much radioactive material can be taken to a local sanitary landfill is not so much a scientific or technical question as it is a societal, philosophical, and, therefore, political issue. The issues are mired in the debates about nuclear power, nuclear weapons, big business, and distrust of government. Scientific and regulatory bodies add to the general public's true fears, concerns, uncertainties, and mistrust of radiation and things radioactive when they fail to act in a concise, logical, and at least coordinated manner. The bifurcation of standard setting responsibility at the federal level between the U.S. Nuclear Regulatory Commission (NRC) and the U.S. Environmental Protection Agency and the agreement state system of regulating radioactive materials all add to the public's confusion and anxiety. The purpose of this paper is to point out from the viewpoint of a state regulatory agency problems that are seen as stumbling blocks to the implementation and acceptance of a below-regulatory-concern (BRC) policy

  3. Omni-directional selective shielding material based on amorphous glass coated microwires.

    Science.gov (United States)

    Ababei, G; Chiriac, H; David, V; Dafinescu, V; Nica, I

    2012-01-01

    The shielding effectiveness of the omni-directional selective shielding material based on CoFe-glass coated amorphous wires in 0.8 GHz-3 GHz microwave frequency range is investigated. The measurements were done in a controlled medium using a TEM cell and in the free space using horn antennas, respectively. Experimental results indicate that the composite shielding material can be developed with desired shielding effectiveness and selective absorption of the microwave frequency range by controlling the number of the layers and the length of microwires.

  4. Material Selection for Competition–A Case Study for Air Coolers

    Directory of Open Access Journals (Sweden)

    Luma A. H. Al Kindi

    2018-02-01

    Full Text Available Competition is one of the most important challenges that is facing the marketing of industrial products in today's markets. In this research study of the impact of material selection factor for air coolers of different materials is applied. Investigation on the air cooler windows which are part of the body of air coolers is conducted. Corrosion resistance, thermal conductivity, strength of material, weight, shape, cost and manufacturing process are the factors that are applied and calculated on three types of materials Aluminum, Galvanized steel and polypropylene. The physical properties of the three mentioned materials are used to calculate Merit Index .The corrosion average, according to Tafel Method depending the corrosion current and adopting contactors for the anodic and cathodic metals behaviors is performed. ANSYS is adopted using the three samples for the selected materials Aluminum, Galvanized steel and polypropylene to measure maximum stress and deflection are measured. Accordingly, the results are compared to choose the best alternative. It is observed that the polypropylene is the best choice depending three factors while the aluminum material is better depending two factors and the galvanized steel is regarded as the best in only one factor, the rest factors are identical when choosing  an alternative material for manufacturing the air cooler windows.

  5. AN ASSESSMENT OF FACTORS AFFECTING MATERIAL STOCK CONTROL PRACTICE ON SELECTED CONSTRUCTION SITES IN NIGERIA

    OpenAIRE

    Adafin, Johnson Kayode; Ayodele, Elijah Olusegun; Daramola, Olufemi

    2011-01-01

    This research examines the stock control methods utilized by construction firms on construction sites with a view to assessing the factors affecting material stock control practice by construction firms as well as determining the impact of factors affecting material stock control on building project performance. Data were collected with the aid of well-structured questionnaire administered on a number of construction professionals and technicians in some randomly selected building constructio...

  6. Aspects for selection of materials and fabrication processes for nuclear component manufacturing

    International Nuclear Information System (INIS)

    Pernstich, K.

    1980-01-01

    For components of the Nuclear steam supply System of Light Water Reactors an extremely high safety standard is required. These requirements only can be met by adequate selection of materials and fabrication processes and their proper application in combination with strict quality assurance and control measurements. A general overview of the basic aspects to be considered in this connection is presented together with an indication of the present state of art for the main materials and fabrication processes. (author) [pt

  7. A life cycle framework to support materials selection for Ecodesign: A case study on biodegradable polymers

    International Nuclear Information System (INIS)

    Ribeiro, I.; Peças, P.; Henriques, E.

    2013-01-01

    Highlights: • Life cycle framework to support material selection in Ecodesign. • Early design stage estimates and sensitivity analyses based on process-based models. • Sensitivity analysis to product geometry, industrial context and EoL scenarios. • Cost and environmental performance comparison – BDP vs. fossil based polymers. • Best alternatives mapping integrating cost and environmental performances. - Abstract: Nowadays society compels designers to develop more sustainable products. Ecodesign directs product design towards the goal of reducing environmental impacts. Within Ecodesign, materials selection plays a major role on product cost and environmental performance throughout its life cycle. This paper proposes a comprehensive life cycle framework to support Ecodesign in material selection. Dealing with new materials and technologies in early design stages, process-based models are used to represent the whole life cycle and supply integrated data to assess material alternatives, considering cost and environmental dimensions. An integrated analysis is then proposed to support decision making by mapping the best alternative materials according to the importance given to upstream and downstream life phases and to the environmental impacts. The proposed framework is applied to compare the life cycle performance of injection moulded samples made of four commercial biodegradable polymers with different contents of Thermo Plasticized Starch and PolyLactic Acid and a common fossil based polymer, Polypropylene. Instead of labelling materials just as “green”, the need to fully capture all impacts in the whole life cycle was shown. The fossil based polymer is the best economic alternative, but polymers with higher content of Thermo Plasticized Starch have a better environmental performance. However, parts geometry and EoL scenarios play a major role on the life cycle performance of candidate materials. The selection decision is then supported by mapping

  8. The use of selective electrodes for the control of nuclear materials

    International Nuclear Information System (INIS)

    Pires, M.A.F.; Abrao, A.

    1984-01-01

    The use of ion selective electrodes is discussed for the determination of nitrate, chloride and fluoride in several materials used in the fuel cycle. The determination of nitrate and chloride in thorium compounds, the analysis of fluoride and chloride in uranium compounds and the determination of fluoride in crude phosphoric acid are described. The control of fluoride in urine of individuals that handle materials containing fluor and its compounds is also described. (C.L.B.) [pt

  9. Global Variation of Human Papillomavirus Genotypes and Selected Genes Involved in Cervical Malignancies.

    Science.gov (United States)

    Husain, R S Akram; Ramakrishnan, V

    2015-01-01

    Carcinoma of the cervix is ranked second among the top 5 cancers affecting women globally. Parallel to other cancers, it is also a complex disease involving numerous factors such as human papillomavirus (HPV) infection followed by the activity of oncogenes and environmental factors. The incidence rate of the disease remains high in developing countries due to lack of awareness, followed by mass screening programs, various socioeconomic issues, and low usage of preventive vaccines. Over the past 3 decades, extensive research has taken place in cervical malignancy to elucidate the role of host genes in the pathogenesis of the disease, yet it remains one of the most prevalent diseases. It is imperative that recent genome-wide techniques be used to determine whether carcinogenesis of oncogenes is associated with cervical cancer at the molecular level and to translate that knowledge into developing diagnostic and therapeutic tools. The aim of this study was to discuss HPV predominance with their genotype distribution worldwide, and in India, as well as to discuss the newly identified oncogenes related to cervical cancer in current scenario. Using data from various databases and robust technologies, oncogenes associated with cervical malignancies were identified and are explained in concise manner. Due to the advent of recent technologies, new candidate genes are explored and can be used as precise biomarkers for screening and developing drug targets. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

  10. MRI and neuropathological validations of the involvement of air pollutants in cortical selective neuronal loss.

    Science.gov (United States)

    Ejaz, Sohail; Anwar, Khaleeq; Ashraf, Muhammad

    2014-03-01

    Vehicles are a major source of air pollution, especially particulate matter (PM) pollution, throughout the world and auto-rickshaws are considered main contributors to this air pollution. PM, in addition to causing respiratory and cardiovascular disorders, has potential to gain access to the brain and could induce neuroinflammation leading to different neurological disorders. Therefore, in the current project, MRI and immunohistochemistry techniques were adopted to ascertain the neurotoxic potential of the chronic exposure to different PM generated by two-stroke auto-rickshaws (TSA), four-stroke auto-rickshaws (FSA), and aluminum sulfate (AS) solution in rats. The results highlighted that all treated groups followed a pattern of dose-dependent increase in pure cortical neuronal loss, selective neuronal loss (SNL), nuclear pyknosis, karyolysis, and karyorrhexis. Mild to moderate areas of penumbra were also observed with increase in the population of activated microglia and astrocytes, while no alteration in the intensities of T2W MRI signals was perceived in any group. When comparing the findings, TSA possess more neurotoxic potential than FSA and AS, which could be associated with increased concentration of certain elements in TSA emissions. The study concludes that chronic exposure to PM from TSA, FSA, and AS solutions produces diverse neuropathies in the brain, which may lead to different life-threatening neurological disorders like stroke, Alzheimer's, and Parkinson's disorders. Government and environmental agencies should take serious notice of this alarming situation, and immediate steps should be implemented to improve the standards of PM emissions from auto-rickshaws.

  11. Multiple criteria decision making with life cycle assessment for material selection of composites

    Directory of Open Access Journals (Sweden)

    A. S. Milani

    2011-12-01

    Full Text Available With the advancement of interdisciplinary approaches in today’s modern engineering, current efforts in optimal design of composites include seeking material selection protocols that can (1 simultaneously consider a series of mechanical/electrical/chemical cost criteria over a set of alternative material options, and (2 closely take into account environmental aspects of final products including recycling and end-of-life disposal options. In this paper, in addition to a review of some recent experimental and methodological advances in the above areas, a new application of multiple criteria decision making (MCDM is presented to deal with decision conflicts often seen among design criteria in composite material selection with the help of life cycle assessment (LCA. To show the application, an illustrative case study on a plastic gear material selection is conducted where the cost, mechanical and thermal properties along with environmental impact criteria are to be satisfied simultaneously. A pure plastic gear is compared to a Polyethylene terephthalate (PET/aluminum-powder composite alternative. Results suggest that simple MCDM models, including a signal-to-noise measure adapted to MCDM in the same case study, can be used to explore both trade-offs and design break-even points in large decision spaces as the decision maker’s perspective over environmental, material performance and cost attributes change during the design process. More advanced topics including the account of material data uncertainties are addressed.

  12. Doublet III limiter performance and implications for mechanical design and material selection for future limiters

    International Nuclear Information System (INIS)

    Sabado, M.M.; Marcus, F.B.; Trester, P.W.; Wesley, J.C.

    1979-10-01

    The plasma limiter system for Doublet III is described. Initially, high-Z materials, Ta-10W for the primary limiter and Mo for the backup limiters, were selected as the most attractive metallic candidates from the standpoint of thermal and structural properties. For the purpose of evaluating the effect of material Z on plasma performance, the nonmagnetic, Ni-base alloy Inconel X-750 was selected for a medium-Z limiter material. Graphite, a low-Z material, will likely be the next limiter material for evaluation. Design and material selection criteria for the different Z ranges are presented. The performance of the high-Z limiters in Doublet III is reviewed for an operation period that included approximately 5000 plasma shots. Changes in surface appearance and metallurgical changes are characterized. Discussion is presented on how and to what extent the high-Z elements affected the performance of the plasma based on theory and measurements in Doublet III. The fabrication processes for the Inconel X-750 limiters are summarized, and, last, observations on early performance of the Inconel limiters are described

  13. Doublet III limiter performance and implications for mechanical design and material selection for future limiters

    Energy Technology Data Exchange (ETDEWEB)

    Sabado, M.M.; Marcus, F.B.; Trester, P.W.; Wesley, J.C.

    1979-10-01

    The plasma limiter system for Doublet III is described. Initially, high-Z materials, Ta-10W for the primary limiter and Mo for the backup limiters, were selected as the most attractive metallic candidates from the standpoint of thermal and structural properties. For the purpose of evaluating the effect of material Z on plasma performance, the nonmagnetic, Ni-base alloy Inconel X-750 was selected for a medium-Z limiter material. Graphite, a low-Z material, will likely be the next limiter material for evaluation. Design and material selection criteria for the different Z ranges are presented. The performance of the high-Z limiters in Doublet III is reviewed for an operation period that included approximately 5000 plasma shots. Changes in surface appearance and metallurgical changes are characterized. Discussion is presented on how and to what extent the high-Z elements affected the performance of the plasma based on theory and measurements in Doublet III. The fabrication processes for the Inconel X-750 limiters are summarized, and, last, observations on early performance of the Inconel limiters are described. (MOW)

  14. A frictional contact problem with wear involving elastic-viscoplastic materials with damage and thermal effects

    Directory of Open Access Journals (Sweden)

    Abdelmoumene Djabi

    2015-05-01

    Full Text Available We consider a mathematical problem for quasistatic contact between a thermo-elastic-viscoplastic body with damage and an obstacle. The contact is frictional and bilateral with a moving rigid foundation which results in the wear of the contacting surface. We employ the thermo-elasticviscoplastic with damage constitutive law for the material. The damage of the material caused by elastic deformations. The evolution of the damage is described by an inclusion of parabolic type. The problem is formulated as a coupled system of an elliptic variational inequality for the displacement, a parabolic variational inequality for the damage and the heat equation for the temperature. We establish a variational formulation for the model and we prove the existence of a unique weak solution to the problem. The proof is based on a classical existence and uniqueness result on parabolic inequalities, differential equations and fixed point arguments.

  15. Transition from site selection to site confirmation phase: New challenge to Posiva's communication and public involvement

    International Nuclear Information System (INIS)

    Seppaelae, Timo

    2001-01-01

    In Finland, Posiva Oy is responsible for the final disposal of spent nuclear fuel. In the 1990's investigations have been carried out on four intended sites for final disposal. Posiva implemented Environmental Impact Assessment (EIA) on the investigation sites in 1997-1999. The results of the EIA procedure were published in the EIA report which was attached to the application filed to the Government in May 1999 for a policy decision on the construction of the final disposal facility in Olkiluoto in the municipality of Eurajoki. In December 2000, the Finnish Government made a favourable policy decision ( D ecision in Principle ) on the construction of final disposal facility for spent nuclear fuel in Olkiluoto. According to the decision, the facility is in line with the overall good of the society. According to the Government's decision the prerequisites of the policy decision had been met. The municipality of Eurajoki supported the construction of the facility in Olkiluoto and STUK, the Radiation and Nuclear Safety Authority, also approved of the advancement of the project. The positive policy decision of the Government will still need to be ratified by the Parliament. The parliamentary proceedings of the policy decision will probably start in February 2001. The policy decision will make it possible for Posiva to concentrate the future site confirmation studies in Olkiluoto, Eurajoki, and construct an underground research facility there. The excavation of the research facility in the bedrock is planned to start in a few years' time. The construction of the final disposal facility is scheduled to start after the year 2010. The transition from the site selection to the site confirmation phase in Eurajoki means a new challenge not only to Posiva's research work but also to Posiva's communication. In addition to meeting the safety criteria, Posiva's activities shall in the future also meet all the criteria specified by the surrounding society

  16. Bacterial evolution through the selective loss of beneficial Genes. Trade-offs in expression involving two loci.

    Science.gov (United States)

    Zinser, Erik R; Schneider, Dominique; Blot, Michel; Kolter, Roberto

    2003-01-01

    The loss of preexisting genes or gene activities during evolution is a major mechanism of ecological specialization. Evolutionary processes that can account for gene loss or inactivation have so far been restricted to one of two mechanisms: direct selection for the loss of gene activities that are disadvantageous under the conditions of selection (i.e., antagonistic pleiotropy) and selection-independent genetic drift of neutral (or nearly neutral) mutations (i.e., mutation accumulation). In this study we demonstrate with an evolved strain of Escherichia coli that a third, distinct mechanism exists by which gene activities can be lost. This selection-dependent mechanism involves the expropriation of one gene's upstream regulatory element by a second gene via a homologous recombination event. Resulting from this genetic exchange is the activation of the second gene and a concomitant inactivation of the first gene. This gene-for-gene expression tradeoff provides a net fitness gain, even if the forfeited activity of the first gene can play a positive role in fitness under the conditions of selection. PMID:12930738

  17. Bacterial evolution through the selective loss of beneficial Genes. Trade-offs in expression involving two loci.

    Science.gov (United States)

    Zinser, Erik R; Schneider, Dominique; Blot, Michel; Kolter, Roberto

    2003-08-01

    The loss of preexisting genes or gene activities during evolution is a major mechanism of ecological specialization. Evolutionary processes that can account for gene loss or inactivation have so far been restricted to one of two mechanisms: direct selection for the loss of gene activities that are disadvantageous under the conditions of selection (i.e., antagonistic pleiotropy) and selection-independent genetic drift of neutral (or nearly neutral) mutations (i.e., mutation accumulation). In this study we demonstrate with an evolved strain of Escherichia coli that a third, distinct mechanism exists by which gene activities can be lost. This selection-dependent mechanism involves the expropriation of one gene's upstream regulatory element by a second gene via a homologous recombination event. Resulting from this genetic exchange is the activation of the second gene and a concomitant inactivation of the first gene. This gene-for-gene expression tradeoff provides a net fitness gain, even if the forfeited activity of the first gene can play a positive role in fitness under the conditions of selection.

  18. Model to predict radiological consequences of transportation accidents involving dispersal of radioactive material in urban areas

    International Nuclear Information System (INIS)

    Taylor, J.M.; Daniel, S.L.

    1978-01-01

    The analysis of accidental releases of radioactive material which may result from transportation accidents in high-density urban areas is influenced by several urban characteristics which make computer simulation the calculational method of choice. These urban features fall into four categories. Each of these categories contains time- and location-dependent parameters which must be coupled to the actual time and location of the release in the calculation of the anticipated radiological consequences. Due to the large number of dependent parameters a computer model, METRAN, has been developed to quantify these radiological consequences. Rather than attempt to describe an urban area as a single entity, a specific urban area is subdivided into a set of cells of fixed size to permit more detailed characterization. Initially, the study area is subdivided into a set of 2-dimensional cells. A uniform set of time-dependent physical characteristics which describe the land use, population distribution, traffic density, etc., within that cell are then computed from various data sources. The METRAN code incorporates several details of urban areas. A principal limitation of the analysis is the limited availability of accurate information to use as input data. Although the code was originally developed to analyze dispersal of radioactive material, it is currently being evaluated for use in analyzing the effects of dispersal of other hazardous materials in both urban and rural areas

  19. Study of the physical mechanisms involved in the femtosecond laser optical breakdown of dielectric materials

    International Nuclear Information System (INIS)

    Mouskeftaras, Alexandros

    2013-01-01

    We have carried out detailed time resolved experimental studies of the mechanism of electron excitation-relaxation, when an ultrashort (60 fs -1 ps) laser (UV and IR) pulse interacts with a wide band gap dielectric material. The studies cover a range of different dielectric materials and the investigated regimes span from nondestructive ionization of the material at the low power end (∼TW/cm 2 ) to ablative domain at a higher laser power (∼10 TW/cm 2 ). This gives fundamental insight into the understanding of the laser damaging process taking place under our irradiation conditions. The usage of time-resolved spectral interferometry technique allows to directly measure the electron density of the irradiated material under different excitation conditions and hence leads to quantification of the process. The measurements, carried out at the optical breakdown threshold utilizing different pulse durations, raise questions regarding the usage of critical excitation density as a universal ablation criterion. A new criterion related to the exchanged energy is proposed. Additionally, the use of an experimental setup implementing a double pump pulse allows the identification of different excitation mechanisms taking place at time scales of the order of the pulse duration used. Electronic avalanche is observed in some materials (SiO 2 , NaCl) while this is not the case for others (Al 2 O 3 , MgO). These differences are discussed in detail. Next, we measure the energy spectrum of excited electrons with a complementary technique: the photoemission spectroscopy. These results allow us on one hand to show a crossed effect between the two 'pump' pulses and on the other hand to measure electron relaxation characteristic times, as a function of their kinetic energy. Finally, a morphological study of craters resulting from ablation in the case of a single pulse has been carried out for different irradiation parameters: number of shots, energy and pulse duration. This work has

  20. An integrated approach to selecting materials for fuel cladding in advanced high-temperature reactors

    Energy Technology Data Exchange (ETDEWEB)

    Rangacharyulu, C., E-mail: chary.r@usask.ca [Univ. of Saskatchewan, Saskatoon, SK (Canada); Guzonas, D.A.; Pencer, J.; Nava-Dominguez, A.; Leung, L.K.H. [Atomic Energy of Canada Limited, Chalk River, ON (Canada)

    2014-07-01

    An integrated approach has been developed for selection of fuel cladding materials for advanced high-temperature reactors. Reactor physics, thermalhydraulic and material analyses are being integrated in a systematic study comparing various candidate fuel-cladding alloys. The analyses established the axial and radial neutron fluxes, power distributions, axial and radial temperature distributions, rates of defect formation and helium production using AECL analytical toolsets and experimentally measured corrosion rates to optimize the material composition for fuel cladding. The project has just been initiated at University of Saskatchewan. Some preliminary results of the analyses are presented together with the path forward for the project. (author)

  1. Disease Risk Assessments Involving Companion Animals: an Overview for 15 Selected Pathogens Taking a European Perspective.

    Science.gov (United States)

    Rijks, J M; Cito, F; Cunningham, A A; Rantsios, A T; Giovannini, A

    2016-07-01

    Prioritization of companion animal transmissible diseases was performed by the Companion Animals multisectoriaL interprofessionaL Interdisciplinary Strategic Think tank On zoonoses (CALLISTO) project. The project considered diseases occurring in domesticated species commonly kept as pets, such as dogs and cats, but also included diseases occurring in captive wild animals and production animal species. The prioritization process led to the selection of 15 diseases of prime public health relevance, agricultural economic importance, or both. An analysis was made of the current knowledge on the risk of occurrence and transmission of these diseases among companion animals, and from companion animals to man (zoonoses) or to livestock. The literature was scanned for risk assessments for these diseases. Studies were classified as import risk assessments (IRAs) or risk factor analyses (RFAs) in endemic areas. For those pathogens that are absent from Europe, only IRAs were considered; for pathogens present throughout Europe, only RFAs were considered. IRAs were identified for seven of the eight diseases totally or partially absent from Europe. IRAs for classical rabies and alveolar echinococcosis found an increased risk for introduction of the pathogen into officially disease-free areas as a consequence of abandoning national rules and adopting the harmonized EU rules for pet travel. IRAs for leishmaniosis focused on risk associated with the presence of persistently infected dogs in new geographical areas, taking into consideration the risk of disease establishment should a competent vector arise. IRAs for Crimean-Congo haemorrhagic fever and West Nile fever indicated that the likelihood of introduction via companion animals was low. IRAs for bluetongue paid no attention to the risk of introduction via companion animals, which was also the case for IRAs for foot-and-mouth disease, the only disease considered to be absent from Europe. RFAs dealing with the risk factors for

  2. A successful effort to involve stakeholders in the selection of a site for a corrective action management unit

    International Nuclear Information System (INIS)

    Conway, R.; Merkhofer, M.W.; Oms, E.

    1995-01-01

    As part of the effort to clean up hazardous waste sites, Sandia National Laboratories in New Mexico (SNL/NM) adopted a novel approach to involving stakeholders in a key decision associated with its Environmental Restoration (ER) Project. The decision was where to locate a Corrective Action Management Unit (CAMU), an area designed to consolidate, store, and treat wastes generated from cleanup activities. The decision-making approach was a variation of a technique known as multiattribute utility analysis (MUA). Although MUA has rarely been undertaken during normal Project activities, it proved to be a surprisingly effective means for involving stakeholders in the decision process, generating consensus over a selected site, and enhancing public trust and understanding of Project activities. Requirements and criteria for selecting CAMU sites are provided by the Environmental Protection Agency's (EPA's) CAMU Final Rule (EPA 1993). Recognizing the lack of experience with the Rule and the importance of community understanding and support, the ER Project sought an approach that would allow stakeholders to participate in the site-selection process

  3. Developing a highway emergency response plan for incidents involving hazardous materials, second edition, March 1992

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This provides minimum guidelines for developing an emergency response plan for incidents involving hazardous liquid hydrocarbons, such as gasoline and crude oil, transported in MC 306/DOT 406 and MC 307/DOT 407 aluminum cargo tanks and for coordinating and cooperating with local, state, and federal officials. This publication covers response plan priorities, personnel training, special equipment, media relations, environmental relations, and post-response activities. The apprendixes to this recommended practice outline a highway emergency response plan and suggest a procedure for removing liquid hydrocarbons from overturned cargo tanks and righting the tank vehicles

  4. What's Your Money Worth? Materials Budgets and the Selection and Evaluation of Book and Serial Vendors.

    Science.gov (United States)

    Barker, Joseph W.

    1992-01-01

    Discusses budgets for library materials and how to select and evaluate book and serial vendors. Trends in automation, publishing, and economics that affect both libraries and vendors are discussed; and examples from the University of California at Berkeley that include serials service charges and approval plan discounts are presented. (six…

  5. Listening Diary in the Digital Age: Students' Material Selection, Listening Problems, and Perceived Usefulness

    Science.gov (United States)

    Chen, Cheryl Wei-yu

    2016-01-01

    The current study reports on a group of Taiwanese college students' first-person diary accounts of their private, transactional listening activities outside the classroom. Issues related to students' material selection, listening problems, and perceived usefulness of keeping a listening diary were explored. It was found that most students chose…

  6. Test methods for selection of materials of construction for high-level radioactive waste vitrification. Revision

    International Nuclear Information System (INIS)

    Bickford, D.F.; Corbett, R.A.; Morrison, W.S.

    1986-01-01

    Candidate materials of construction were evaluated for a facility at the Department of Energy's Savannah River Plant to vitrify high-level radioactive waste. Limited operating experience was available under the corrosive conditions of the complex vitrification process. The objective of the testing program was to provide a high degree of assurance that equipment will meet or exceed design lifetimes. To meet this objective in reasonable time and minimum cost, a program was designed consisting of a combination of coupon immersion and electrochemical laboratory tests and pilot-scale tests. Stainless steels and nickel-based alloys were tested. Alloys that were most resistant to general and local attack contained nickel, molybdenum (>9%), and chromium (where Cr + Mo > 30%). Alloy C-276 was selected as the reference material for process equipment. Stellite 6 was selected for abrasive service in the presence of formic acid. Alloy 690 and ALLCORR were selected for specific applications

  7. Selection of sorption material for tests of pesticide permeation through protective clothing fabrics.

    Science.gov (United States)

    Krzemińska, Sylwia; Nazimek, Teresa

    2004-01-01

    The paper presents the results of studies on selecting a solid sorption material for absorbing liquid crop protection agents which permeate samples of protective clothing fabrics. The sorption materials were investigated and selected with an assumption that they should have a high recovery coefficient for biologically active substances, used as active ingredients in crop protection agents, at a presumed, acceptably high level. The selected substances were determined with a gas chromatograph equipped with an electron capture detector (dichlorvos, cypermethrin and 2,4-D) and a nitrogen-phosphorus detector (carbofuran). The tests demonstrated that polypropylene melt-blown type unwoven cloth had high recovery coefficients for all 4 active ingredients proposed for the study. The highest recovery coefficient, -.97, was obtained for carbofuran. The recovery coefficients obtained for the 3 remaining substances were lower: .89 for cypermethrin and 2,4-D, and .84 for dichlorvos.

  8. Selective Preparation of trans-Carveol over Ceria Supported Mesoporous Materials MCM-41 and SBA-15

    Directory of Open Access Journals (Sweden)

    Nariman F. Salakhutdinov

    2013-05-01

    Full Text Available Ce-modified mesoporous silica materials MCM-41 and SBA-15, namely 32 wt % Ce–Si–MCM-41, 16 wt % Ce–H–MCM-41 and 20 wt % Ce–Si–SBA-15, were prepared, characterized and studied in the selective preparation of trans-carveol by α-pinene oxide isomerization. The characterizations of these catalysts were performed using scanning electron microscopy, X-ray photoelectron spectroscopy, nitrogen adsorption and FTIR pyridine adsorption. Selective preparation of trans-carveol was carried out in the liquid phase in a batch reactor. The activity and the selectivity of catalyst were observed to be influenced by their acidity, basicity and morphology of the mesoporous materials. The formation of trans-carveol is moreover strongly influenced by the basicity of the used solvent and in order to achieve high yields of this desired alcohol it is necessary to use polar basic solvent.

  9. BIM-Based Decision Support System for Material Selection Based on Supplier Rating

    Directory of Open Access Journals (Sweden)

    Abiola Akanmu

    2015-12-01

    Full Text Available Material selection is a delicate process, typically hinged on a number of factors which can be either cost or environmental related. This process becomes more complicated when designers are faced with several material options of building elements and each option can be supplied by different suppliers whose selection criteria may affect the budgetary and environmental requirements of the project. This paper presents the development of a decision support system based on the integration of building information models, a modified harmony search algorithm and supplier performance rating. The system is capable of producing the cost and environmental implications of different material combinations or building designs. A case study is presented to illustrate the functionality of the developed system.

  10. The Choice Method of Selected Material has influence single evaporation flash method

    International Nuclear Information System (INIS)

    Sunaryo, Geni Rina; Sumijanto; Nurul L, Siti

    2000-01-01

    The final objective of this research is to design the mini scale of desalination installation. It has been started from 1997/1998 and has been doing for this 3 years. Where the study on the assessment of various desalination system has been done in the first year and thermodynamic in the second year. In this third year, literatully study on material resistance from outside pressure has been done. The number of pressure for single evaporator flashing method is mainly depend on the temperature that applied in that system. In this paper, the configuration stage, the choice method of selecting material for main evaporator vessel, tube, tube plates, water boxes, pipework, and valves for multistage flash distillation will be described. The choice of selecting material for MSF is base on economical consideration, cheap, high resistance and easy to be maintained

  11. Group IV all-semiconductor spintronics. Materials aspects and optical spin selection rules

    Energy Technology Data Exchange (ETDEWEB)

    Sircar, Narayan

    2012-04-03

    particular, by including recent theory on spin-dependent selection rules for radiative transitions in bulk Si, we adapt an expression for the magnetic-field-induced photoluminescence polarization of direct band gap semiconductor materials of GaAs-type to Si. Measurements within an applied magnetic field of the degree of circular polarization of phononassisted photoluminescence of bulk Si for different doping are presented. Similar experiments on the photoluminescence of Ge quantum dot ensembles evidence a peculiarity for the spin-dependent selection rules for phononless radiative recombinations. We propose a connection between this finding and the confined character of electrons that are involved in the transitions. Furthermore, we try to optically inject and detect confined carrier spins in Ge quantum dot ensembles. For nonresonant excitation these efforts are unsuccessful, which we attribute to a hole spin relaxation that happens faster than the combined capture of the hole by the quantum dot and the radiative decay of the hole. Finally, we employ the p-type GeMn thin film layers presented in the first part of this work as spin-polarizing contacts for Si/SiGe-based light-emitting diodes with the aim to inject spin-polarized holes. Preliminary results of a circularly polarized electroluminescence of these devices propose the possibility of a successful hole spin injection near liquid helium temperatures.

  12. International conference on safe decommissioning for nuclear activities: Assuring the safe termination of practices involving radioactive materials. Contributed papers

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-07-01

    Thousands of operations involving the use of radioactive substances will end during the current century. While there is considerable regulatory experience in the 'front end' of the regulatory system for practices, the experience at the back end is more limited as fewer practices have actually been terminated. When a practice is terminated because the facility has reached the end of its useful life, action has to betaken to ensure the safe shutdown of the facility and allow the removal of regulatory controls. There are many issues involved in the safe termination of practices. These include setting criteria for the release of material and sites from regulatory control; determining the suitability of the various options for decommissioning nuclear facilities, managing the waste and material released from control (recycling, reuse or disposal), and the eventual remediation of the site. Some countries have put in place regulatory infrastructures and have developed programmes to manage the associated decommissioning and remediation activities. Other countries are at the stage of assessing what is involved in terminating such practices. The purpose of this Conference is to foster an information exchange on the safe an orderly termination of practices that involve the use of radioactive substances, including both decommissioning and environmental remediation, and to promote improved coherence internationally on strategies and criteria for the safe termination of practices.

  13. International conference on safe decommissioning for nuclear activities: Assuring the safe termination of practices involving radioactive materials. Contributed papers

    International Nuclear Information System (INIS)

    2002-01-01

    Thousands of operations involving the use of radioactive substances will end during the current century. While there is considerable regulatory experience in the 'front end' of the regulatory system for practices, the experience at the back end is more limited as fewer practices have actually been terminated. When a practice is terminated because the facility has reached the end of its useful life, action has to betaken to ensure the safe shutdown of the facility and allow the removal of regulatory controls. There are many issues involved in the safe termination of practices. These include setting criteria for the release of material and sites from regulatory control; determining the suitability of the various options for decommissioning nuclear facilities, managing the waste and material released from control (recycling, reuse or disposal), and the eventual remediation of the site. Some countries have put in place regulatory infrastructures and have developed programmes to manage the associated decommissioning and remediation activities. Other countries are at the stage of assessing what is involved in terminating such practices. The purpose of this Conference is to foster an information exchange on the safe an orderly termination of practices that involve the use of radioactive substances, including both decommissioning and environmental remediation, and to promote improved coherence internationally on strategies and criteria for the safe termination of practices

  14. Selectivity in inter polymer complexation involving phenolic copolymer, poly electrolytes, non-ionic polymers and transition metal ions

    International Nuclear Information System (INIS)

    Vasheghani Farahani, B.; Hosseinpour Rajabi, F.

    2006-01-01

    Selectivity in inter polymer complex formation involving a typical four-component phenolic copolymer (ρ-chloro phenol-ρ-aminophenol-ρ-toluidine-ρ-cresol- HCHO copolymer), poly electrolytes such as polyethylene imine and polyacrylic acid, a non-ionic homopolymer polyvinyl pyrrolidone, and some transition metal ions (e.g., Cu (II), Ni (11)) have been studied in dimethylformamide-methanol solvents mixture. The coordinating groups of phenolic copolymer form complexes through hydrogen bonding and ion-dipole interactions. The different stages of interactions have been studied by several experimental techniques, e.g., viscometry, potentiometry and conductometry. Some schemes have been suggested to explain the mode of interaction between these components

  15. Effect of repeated contact on adhesion measurements involving polydimethylsiloxane structural material

    International Nuclear Information System (INIS)

    Kroner, E; Arzt, E; Maboudian, R

    2009-01-01

    During the last few years several research groups have focused on the fabrication of artificial gecko inspired adhesives. For mimicking these structures, different polymers are used as structure material, such as polydimethylsiloxanes (PDMS), polyurethanes (PU), and polypropylene (PP). While these polymers can be structured easily and used for artificial adhesion systems, the effects of repeated adhesion testing have never been investigated closely. In this paper we report on the effect of repeated adhesion measurements on the commercially available poly(dimethylsiloxane) polymer kit Sylgard 184 (Dow Corning). We show that the adhesion force decreases as a function of contact cycles. The rate of change and the final value of adhesion are found to depend on the details of the PDMS synthesis and structuring.

  16. Piezoelectric materials involved in road traffic applications test system; Banco de ensayos para materiales piezoelectricos en aplicaciones viales

    Energy Technology Data Exchange (ETDEWEB)

    Vazquez Rodriguez, M.; Jimenez Martinez, F.; Frutos, J. de

    2011-07-01

    The test bench system described in this paper performs experiments on piezoelectric materials used in road traffic applications, covering a range between 14 and 170 km/h, which is considered enough for testing under standard traffic conditions. A software has been developed to control the three phase induction motor driver and to acquire all the measurement data of the piezoelectric materials. The mass over each systems axis can be selected, with a limit of 60 kg over each wheel. The test bench is used to simulate the real behaviour of buried piezoelectric cables in road traffic applications for both light and heavy vehicles. This new test bed system is a powerful research tool and can be applied to determine the optimal installation and configuration of the piezoelectric cable sensors and opens a new field of research: the study of energy harvesting techniques based on piezoelectric materials. (Author) 10 refs.

  17. Selective classification and quantification model of C&D waste from material resources consumed in residential building construction.

    Science.gov (United States)

    Mercader-Moyano, Pilar; Ramírez-de-Arellano-Agudo, Antonio

    2013-05-01

    The unfortunate economic situation involving Spain and the European Union is, among other factors, the result of intensive construction activity over recent years. The excessive consumption of natural resources, together with the impact caused by the uncontrolled dumping of untreated C&D waste in illegal landfills have caused environmental pollution and a deterioration of the landscape. The objective of this research was to generate a selective classification and quantification model of C&D waste based on the material resources consumed in the construction of residential buildings, either new or renovated, namely the Conventional Constructive Model (CCM). A practical example carried out on ten residential buildings in Seville, Spain, enabled the identification and quantification of the C&D waste generated in their construction and the origin of the waste, in terms of the building material from which it originated and its impact for every m(2) constructed. This model enables other researchers to establish comparisons between the various improvements proposed for the minimization of the environmental impact produced by building a CCM, new corrective measures to be proposed in future policies that regulate the production and management of C&D waste generated in construction from the design stage to the completion of the construction process, and the establishment of sustainable management for C&D waste and for the selection of materials for the construction on projected or renovated buildings.

  18. Corrosion of Selected Materials in Boiling Sulfuric Acid for the Nuclear Power Industries

    International Nuclear Information System (INIS)

    Kim, Dong Jin; Lee, Han Hee; Kwon, Hyuk Chul; Kim, Hong Pyo; Hwang, Seong Sik

    2007-01-01

    Iodine sulfur (IS) process is one of the promising processes for a hydrogen production by using a high temperature heat generated by a very high temperature gas cooled reactor(VHTR) in the nuclear power industries. Even though the IS process is very efficient for a hydrogen production and it is not accompanied by a carbon dioxide evolution, the highly corrosive environment of the process limits its application in the industry. Corrosion tests of selected materials were performed in sulfuric acid to select appropriate materials compatible with the IS process. The materials used in this work were Fe-Cr alloys, Fe-Ni-Cr alloys, Fe-Si alloys, Ni base alloys, Ta, Ti, Zr, SiC, Fe-Si, etc. The test environments were 50 wt% sulfuric acid at 120 .deg. C and 98 wt% at 320 .deg. C. Corrosion rates were measured by using a weight change after an immersion. The surface morphologies and cross sectional areas of the corroded materials were examined by using SEM equipped with EDS. Corrosion behaviors of the materials were discussed in terms of the chemical composition of the materials, a weight loss, the corrosion morphology, the precipitates in the microstructure and the surface layer composition

  19. Incident involving radioactive material at IAEA Safeguards Laboratory - No radioactivity released to environment

    International Nuclear Information System (INIS)

    2008-01-01

    Full text: Pressure build-up in a small sealed sample bottle in a storage safe resulted in plutonium contamination of a storage room at about 02:30 today at the IAEA's Safeguards Analytical Laboratory in Seibersdorf. All indications are that there was no release of radioactivity to the environment. Further monitoring around the laboratory will be undertaken. No one was working in the laboratory at the time. The Laboratory's safety system detected plutonium contamination in the storage room where the safe was located and in two other rooms - subsequently confirmed by a team of IAEA radiation protection experts. The Laboratory is equipped with multiple safety systems, including an air-filtering system to prevent the release of radioactivity to the environment. There will be restricted access to the affected rooms until they are decontaminated. A full investigation of the incident will be conducted. The IAEA has informed the Austrian regulatory authority. The IAEA's Laboratory in Seibersdorf is located within the complex of the Austrian Research Centers Seibersdorf (ARC), about 35 km southeast of Vienna. The laboratory routinely analyses small samples of nuclear material (uranium or plutonium) as part of the IAEA's safeguards verification work. (IAEA)

  20. Human biological monitoring for exposure assessment in response to an incident involving hazardous materials.

    Science.gov (United States)

    Scheepers, Paul T J; van Brederode, Nelly E; Bos, Peter M J; Nijhuis, Nicole J; van de Weerdt, Rik H J; van der Woude, Irene; Eggens, Martin L

    2014-12-15

    Biological monitoring in humans (HBM) is widely used in the field of occupational and environmental health. In the situation of an unexpected release of hazardous materials HBM may contribute to the medical support and treatment of exposed individuals from the general population or of emergency responders. Such exposure information may also be used to respond to individual concerns such as questions about a possible relationship between the chemicals released during the incident and health effects. In The Netherlands a guideline was prepared to support early decision-making about the possible use of HBM for exposure assessment during or as soon as possible following a chemical incident. The application of HBM in such an emergency setting is not much different from situations where HBM is normally used but there are some issues that need extra attention such as the choice of the biomarker, the biological media to be sampled, the time point at which biological samples should be collected, the ethics approval and technical implementation of the study protocol and the interpretation and communication of the study results. These issues addressed in the new guideline will support the use of HBM in the management of chemical disasters. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

  1. Communication of work accidents involving biological material: a study in the city of Santa Cruz do Sul/RS

    Directory of Open Access Journals (Sweden)

    Dayane Diehl

    2012-07-01

    Full Text Available Rationale and Objectives: Healthcare workers are constantly exposed to the risk of occupational accidents involving biological material. Thus the aim of the study was to develop a profile of workers involved in workplace accidents with biological materials in Santa Cruz do Sul, through the number of notifications made in information systems. Methods: Transversal retrospective study with a quantitative approach; data collection was carried out between the years 2008 and 2010 from medical records in the Municipal Reference Occupational Health Unit – UMREST – containing the notification via Individual Report of Accident Notification - RINA, and/or Work Accident Communication - CAT. Results: A total of 1,263 records were analyzed during the study period. There were 13 notifications in 2008, 7 cases in 2009 and 2 in 2010. Five records had CAT, 8 had RINA and 9 had RINA and CAT. The most frequently affected professional category was the nursing technician, with the highest frequency in 2008, followed by dentists and nurses. There was a higher prevalence of female workers, with 18 cases. The most prevalent age group was 20 to 49 years old. Conclusion: The study showed that women working in the nursingprofession at the productive-age group are the ones most often affected by work accidents involving biological material during the study period. The study results raise the suspicion of underreporting of accidents with biological material, considering the number of notifications in thesetting of records found in the investigated UMREST. KEYWORDS Wo rk-related accidents. Health care professional. Occupational accidents.

  2. Characterization of rich in calcium materials using X-ray selective absorbers

    International Nuclear Information System (INIS)

    Guereca, G.; Ruvalcaba, J.L.

    2004-01-01

    For Particle Induced X-ray Emission Spectroscopy (PIXE) and X-ray Fluorescence Technique (FRX), the analysis of materials rich in one or two elements may present some difficulties due to high counting rates and saturation effects in X-ray detectors. In this case, it is possible to use selective absorbers in order to reduce the intensity of the major elements with low attenuation for the X-rays of other elements of the material. Using selective absorbers, the detection limits and the sensitivity are increased. For rich Ca materials (shells, bone, teeth and stucco, for instance), the high intensity of Ca X-rays interferes with the detection of lighter and heavier elements. Cl, Ar and Ag compounds are good candidates for Ca selective absorbers, but only Ag and Ar may have a practical absorber thickness. A selective absorber for Ca X-rays using a combination of thin Ag films and a flux of Ar and He was tested at the external beam setup of the Tandem Pelletron Accelerator for PIXE measurements. The improvement on elements detection on bone and colored stucco is shown. (Author) 8 refs., 2 tabs., 8 figs

  3. Normalization Methods and Selection Strategies for Reference Materials in Stable Isotope Analyes. Review

    Energy Technology Data Exchange (ETDEWEB)

    Skrzypek, G. [West Australian Biogeochemistry Centre, John de Laeter Centre of Mass Spectrometry, School of Plant Biology, University of Western Australia, Crawley (Australia); Sadler, R. [School of Agricultural and Resource Economics, University of Western Australia, Crawley (Australia); Paul, D. [Department of Civil Engineering (Geosciences), Indian Institute of Technology Kanpur, Kanpur (India); Forizs, I. [Institute for Geochemical Research, Hungarian Academy of Sciences, Budapest (Hungary)

    2013-07-15

    Stable isotope ratio mass spectrometers are highly precise, but not accurate instruments. Therefore, results have to be normalized to one of the isotope scales (e.g., VSMOW, VPDB) based on well calibrated reference materials. The selection of reference materials, numbers of replicates, {delta}-values of these reference materials and normalization technique have been identified as crucial in determining the uncertainty associated with the final results. The most common normalization techniques and reference materials have been tested using both Monte Carlo simulations and laboratory experiments to investigate aspects of error propagation during the normalization of isotope data. The range of observed differences justifies the need to employ the same sets of standards worldwide for each element and each stable isotope analytical technique. (author)

  4. Material radioassay and selection for the XENON1T dark matter experiment

    Energy Technology Data Exchange (ETDEWEB)

    Aprile, E.; Anthony, M.; De Perio, P.; Gao, F.; Goetzke, L.W.; Greene, Z.; Lin, Q.; Messina, M.; Plante, G.; Rizzo, A.; Zhang, Y. [Columbia University, Physics Department, New York, NY (United States); Aalbers, J.; Breur, P.A.; Brown, A.; Colijn, A.P.; Decowski, M.P.; Hogenbirk, E.; Tiseni, A. [Nikhef and the University of Amsterdam, Amsterdam (Netherlands); Agostini, F. [INFN-Laboratori Nazionali del Gran Sasso, L' Aquila (Italy); Gran Sasso Science Institute, L' Aquila (Italy); University of Bologna, Department of Physics and Astrophysics, Bologna (Italy); INFN-Bologna (Italy); Alfonsi, M.; Geis, C.; Grignon, C.; Oberlack, U.; Scheibelhut, M.; Schindler, S. [Johannes Gutenberg-Universitaet Mainz, Institut fuer Physik and Exzellenzcluster PRISMA, Mainz (Germany); Amaro, F.D.; Cardoso, J.M.R.; Lopes, J.A.M.; Santos, J.M.F. dos; Silva, M. [University of Coimbra, LIBPhys, Department of Physics, Coimbra (Portugal); Arneodo, F.; Benabderrahmane, M.L.; Maris, I. [New York University Abu Dhabi, Abu Dhabi (United Arab Emirates); Barrow, P.; Baudis, L.; Di Giovanni, A.; Franco, D.; Galloway, M.; Kessler, G.; Kish, A.; Mayani, D.; Pakarha, P.; Piastra, F.; Wei, Y.; Wulf, J. [University of Zurich, Physik Institut, Zurich (Switzerland); Bauermeister, B. [Johannes Gutenberg-Universitaet Mainz, Institut fuer Physik and Exzellenzcluster PRISMA, Mainz (Germany); Stockholm University, AlbaNova, Oskar Klein Centre, Department of Physics, Stockholm (Sweden); Berger, T.; Brown, E.; Piro, M.C. [Rensselaer Polytechnic Institute, Department of Physics, Applied Physics and Astronomy, Troy, NY (United States); Sivers, M. von [Rensselaer Polytechnic Institute, Troy, NY (United States). Dept. of Physics, Applied Physics and Astronomy; Bern Univ. (Switzerland). Albert Einstein Center for Fundamental Physics; Bruenner, S.; Cichon, D.; Eurin, G.; Hasterok, C.; Lindemann, S.; Lindner, M.; Marrodan Undagoitia, T.; Pizzella, V.; Rauch, L.; Rupp, N.; Schreiner, J.; Simgen, H. [Max-Planck-Institut fuer Kernphysik, Heidelberg (Germany); Bruno, G.; Gallo Rosso, A.; Molinario, A.; Laubenstein, M.; Nisi, S. [INFN-Laboratori Nazionali del Gran Sasso, L' Aquila (Italy); Gran Sasso Science Institute, L' Aquila (Italy); Budnik, R.; Itay, R.; Landsman, H.; Lellouch, D.; Levinson, L.; Manfredini, A.; Priel, N. [Weizmann Institute of Science, Department of Particle Physics and Astrophysics, Rehovot (Israel); Buetikofer, L.; Coderre, D.; Kaminsky, B.; Schumann, M. [Universitaet Freiburg, Physikalisches Institut, Freiburg (Germany); Calven, J.; Conrad, J.; Ferella, A.D.; Pelssers, B. [Stockholm University, AlbaNova, Oskar Klein Centre, Department of Physics, Stockholm (Sweden); Cervantes, M.; Lang, R.F.; Masson, D.; Pienaar, J.; Reichard, S.; Reuter, C. [Purdue University, Department of Physics and Astronomy, West Lafayette, IN (United States); Cussonneau, J.P.; Diglio, S.; Le Calloch, M.; Masbou, J.; Micheneau, K.; Persiani, R.; Thers, D. [Universite de Nantes, SUBATECH, Ecole des Mines de Nantes, CNRS/IN2P3, Nantes (France); Di Gangi, P.; Garbini, M.; Massoli, F.V.; Sartorelli, G.; Selvi, M. [University of Bologna, Department of Physics and Astrophysics, Bologna (Italy); INFN-Bologna (Italy); Fei, J.; Ni, K.; Ye, J. [University of California, Department of Physics, San Diego, CA (United States); Fieguth, A.; Murra, M.; Rosendahl, S.; Weinheimer, C. [Westfaelische Wilhelms-Universitaet Muenster, Institut fuer Kernphysik, Muenster (Germany); Fulgione, W. [INFN-Laboratori Nazionali del Gran Sasso, L' Aquila (Italy); Gran Sasso Science Institute, L' Aquila (Italy); INFN-Torino (Italy); Osservatorio Astrofisico di Torino, Torino (Italy); Grandi, L.; Saldanha, R.; Shockley, E.; Upole, N. [University of Chicago, Department of Physics and Kavli Institute of Cosmological Physics, Chicago, IL (United States); Miguez, B.; Trinchero, G. [INFN-Torino (Italy); Osservatorio Astrofisico di Torino, Torino (Italy); Naganoma, J.; Shagin, P. [Rice University, Department of Physics and Astronomy, Houston, TX (United States); Scotto Lavina, L. [Universite Pierre et Marie Curie, Universite Paris Diderot, CNRS/IN2P3, LPNHE, Paris (France); Stein, A.; Wang, H. [University of California, Physics and Astronomy Department, Los Angeles, CA (United States); Tunnell, C. [Nikhef and the University of Amsterdam, Amsterdam (Netherlands); University of Chicago, Department of Physics and Kavli Institute of Cosmological Physics, Chicago, IL (United States); Collaboration: XENON Collaboration

    2017-12-15

    The XENON1T dark matter experiment aims to detect weakly interacting massive particles (WIMPs) through low-energy interactions with xenon atoms. To detect such a rare event necessitates the use of radiopure materials to minimize the number of background events within the expected WIMP signal region. In this paper we report the results of an extensive material radioassay campaign for the XENON1T experiment. Using gamma-ray spectroscopy and mass spectrometry techniques, systematic measurements of trace radioactive impurities in over one hundred samples within a wide range of materials were performed. The measured activities allowed for stringent selection and placement of materials during the detector construction phase and provided the input for XENON1T detection sensitivity estimates through Monte Carlo simulations. (orig.)

  5. Radiation tests at cryogenic temperature on selected organic materials for LHC

    International Nuclear Information System (INIS)

    Humer, K.; Weber, H.W.; Szeless, B.; Tavlet, M.

    1997-01-01

    Future multi-TeV particle accelerators like the CERN Large Hadron Collider (LHC) will use superconducting magnets in which organic materials will be exposed to high radiation levels at temperatures as low as 2 K. A representative selection of organic materials comprising insulating films, cable insulations, epoxy resins and composites were exposed to neutron and gamma radiation of a nuclear reactor. Depending on the type of materials, the integrated radiation doses varied between 180 kGy and 155 MGy. During irradiation, the samples were kept close to the boiling temperature of liquid nitrogen, i.e. at 80 K, and thereafter stored in liquid nitrogen and transferred at the same temperature into the testing device for measurement of tensile and flexural strength. Tests were carried out on the same materials at similar dose rates at room temperature, and the results are compared with the ones obtained at cryogenic temperature. They show that within the selected dose range, a number of organic materials are suitable for use in radiation fields of the LHC at cryogenic temperature

  6. Selection of contact bearing couple materials for hip prosthesis using finite element analysis under static conditions

    Science.gov (United States)

    Arirajan, K. A.; Chockalingam, K.; Vignesh, C.

    2018-04-01

    Implants are the artificial parts to replace the missing bones or joints in human anatomy to give mechanical support. Hip joint replacement is an important issue in orthopaedic surgery. The main concern limiting the long-run success of the total hip replacement is the limited service life. Hip replacement technique is widely used in replacing the femur head and acetabular cup by materials that are highly biocompatible. The success of the artificial hip replacement depends upon proper material selection, structure, and shape of the hip prosthesis. Many orthopaedic analyses have been tried with different materials, but ended with partial success on the application side. It is a critical task for selecting the best material pair in the hip prosthesis design. This work develops the finite element analysis of an artificial hip implant to study highest von Mises stress, contact pressure and elastic strain occurs for the dissimilar material combination. The different bearing couple considered for the analysis are Metal on Metal, Metal on Plastic, Metal on Ceramic, Ceramic on Plastic, Ceramic on Ceramic combinations. The analysis is carried out at different static positions of a human (i.e) standing, sitting. The results reveals that the combination with metal in contact with plastic (i.e) Titanium femoral head paired with Ultra High Molecular Weight Poly Ethylene acetabular cup reduces maximum von Mises stress and also it gives lowest contact pressure than other combination of bearing couples.

  7. Selection of materials using multi-criteria decision-making methods with minimum data

    Directory of Open Access Journals (Sweden)

    Shankar Chakraborty

    2013-07-01

    Full Text Available Selection of material for a specific engineering component, which plays a significant role in its design and proper functioning, is often treated as a multi-criteria decision-making (MCDM problem where the most suitable material is to be chosen based on a given set of conflicting criteria. For solving these MCDM problems, the designers do not generally know what should be the optimal number of criteria required for arriving at the best decisive action. Those criteria should be independent to each other and their number should usually limit to seven plus or minus two. In this paper, five material selection problems are solved using three common MCDM techniques to demonstrate the effect of number of criteria on the final rankings of the material alternatives. It is interesting to observe that the choices of the best suited materials solely depend on the criterion having the maximum priority value. It is also found that among the three MCDM methods, the ranking performance of VIKOR (Vlse Kriterijumska Optimizacija Kompromisno Resenje method is the best.

  8. A matrix in life cycle perspective for selecting sustainable materials for buildings in Sri Lanka

    Energy Technology Data Exchange (ETDEWEB)

    Abeysundara, U.G. Yasantha [Ministry of Education, Isurupaya, Battaramulla (Sri Lanka); Babel, Sandhya [Environmental Technology Program, School of Biochemical Engineering and Technology, Sirindhorn International Institute of Technology, Thammasat University, P.O. Box 22, Pathumthani 12121 (Thailand); Gheewala, Shabbir [The Joint Graduate School of Energy and Environment, King Mongkut' s University of Technology Thonburi, Bangkok 10140 (Thailand)

    2009-05-15

    This paper presents a matrix to select sustainable materials for buildings in Sri Lanka, taking into consideration environmental, economic and social assessments of materials in a life cycle perspective. Five building elements, viz., foundations, roofs, ceilings, doors and windows, and floors are analyzed based on materials used for these elements. Environmental burdens associated with these elements are analyzed in terms of embodied energy and environmental impacts such as global warming, acidification and nutrient enrichment. Economic analysis is based on market prices and affordability of materials. Social factors that are taken into account are thermal comfort, interior (aesthetics), ability to construct quickly, strength and durability. By compiling the results of analyses, two building types with minimum and maximum impacts are identified. These two cases along with existing buildings are compared in a matrix of environmental, economic and social scores. Analysis of the results also indicates need for higher consideration of environmental parameters in decision-making over social and economic factors, as social and economic scores do not vary much between cases. Hence, this matrix helps decision-makers to select sustainable materials for buildings, meaningfully, and thus helps to move towards a more sustainable buildings and construction sector. (author)

  9. Results of radiation tests at cryogenic temperature on some selected organic materials for the LHC

    International Nuclear Information System (INIS)

    Schoenbacher, H.; Szeless, B.; Tavlet, M.; Humer, K.; Weber, H.W.

    1996-01-01

    Future multi-TeV particle accelerators like the CERN Large Hadron Collider (LHC) will use superconducting magnets where organic materials will be exposed to high radiation levels at temperatures as low as 2 K. A representative selection of organic materials comprising insulating films, cable insulations, and epoxy-type impregnated resins were exposed to neutron and gamma radiation of a nuclear reactor. Depending on the type of materials, the integrated radiation doses varied between 180 kGy and 155 MGy. During irradiation, the samples were kept close to the boiling temperature of liquid nitrogen i.e. ∼ 80 K and thereafter stored in liquid nitrogen and transferred at the same temperature into the testing device for measurement of tensile and flexural strength. Tests were carried out on the same materials at similar dose rates at room temperature, and the results were compared with those obtained at cryogenic temperature. They show that, within the selected dose range, a number of organic materials are suitable for use in the radiation field of the LHC at cryogenic temperature. (orig.)

  10. Endocytic pathways involved in PLGA nanoparticle uptake by grapevine cells and role of cell wall and membrane in size selection.

    Science.gov (United States)

    Palocci, Cleofe; Valletta, Alessio; Chronopoulou, Laura; Donati, Livia; Bramosanti, Marco; Brasili, Elisa; Baldan, Barbara; Pasqua, Gabriella

    2017-12-01

    PLGA NPs' cell uptake involves different endocytic pathways. Clathrin-independent endocytosis is the main internalization route. The cell wall plays a more prominent role than the plasma membrane in NPs' size selection. In the last years, many studies on absorption and cell uptake of nanoparticles by plants have been conducted, but the understanding of the internalization mechanisms is still largely unknown. In this study, polydispersed and monodispersed poly(lactic-co-glycolic) acid nanoparticles (PLGA NPs) were synthesized, and a strategy combining the use of transmission electron microscopy (TEM), confocal analysis, fluorescently labeled PLGA NPs, a probe for endocytic vesicles (FM4-64), and endocytosis inhibitors (i.e., wortmannin, ikarugamycin, and salicylic acid) was employed to shed light on PLGA NP cell uptake in grapevine cultured cells and to assess the role of the cell wall and plasma membrane in size selection of PLGA NPs. The ability of PLGA NPs to cross the cell wall and membrane was confirmed by TEM and fluorescence microscopy. A strong adhesion of PLGA NPs to the outer side of the cell wall was observed, presumably due to electrostatic interactions. Confocal microscopy and treatment with endocytosis inhibitors suggested the involvement of both clathrin-dependent and clathrin-independent endocytosis in cell uptake of PLGA NPs and the latter appeared to be the main internalization pathway. Experiments on grapevine protoplasts revealed that the cell wall plays a more prominent role than the plasma membrane in size selection of PLGA NPs. While the cell wall prevents the uptake of PLGA NPs with diameters over 50 nm, the plasma membrane can be crossed by PLGA NPs with a diameter of 500-600 nm.

  11. Porous glasses as a host of luminescent materials, their applications and site selective determination

    Energy Technology Data Exchange (ETDEWEB)

    Reisfeld, Renata, E-mail: renata.reisfeld@mail.huji.ac.il [Institute of Chemistry, Hebrew University of Jerusalem, Givat-Ram, Jerusalem 91904 (Israel); Jasinska, Bozena [Institute of Physics, Maria Curie-Sklodowska University, Pl. M. Curie-Skłodowsskiej 1, 20-031 Lublin (Poland); Levchenko, Viktoria [Institute of Chemistry, Hebrew University of Jerusalem, Givat-Ram, Jerusalem 91904 (Israel); Gorgol, Marek [Institute of Physics, Maria Curie-Sklodowska University, Pl. M. Curie-Skłodowsskiej 1, 20-031 Lublin (Poland); Saraidarov, Tsiala; Popov, Inna [Institute of Chemistry, Hebrew University of Jerusalem, Givat-Ram, Jerusalem 91904 (Israel); Antropova, Tatiana [I. V. Grebenshchikov Institute of the Chemistry of Silicates, Russian Academy of Sciences, Nab. Makarova, 2, Liter B, Saint-Petersburg 199034 (Russian Federation); Rysiakiewicz-Pasek, Ewa [Institute of Physics, Wroclaw University of Technology, W. Wyspianskiego 27, 50-370 Wroclaw (Poland)

    2016-01-15

    The site selective distribution of pore sizes in pure porous glasses and glasses doped by a luminescent colorant is determined by luminescent spectroscopy, SEM, SAXS and PALS. The potential applications of the studied materials as environmental and biological sensors are outlined. We suggest how luminescent porous glasses doped by complexes of Gd can act as solid scintillators in tracing elementary particles like neutrino. - Highlights: • Porous glasses are a medium for large number of luminescent materials. • Size distribution of empty and filled pores is studied. • The validity of data obtained by different methods is analyzed.

  12. Factors in the selection of broiler tube materials for a civil fast reactor

    Energy Technology Data Exchange (ETDEWEB)

    Tyzack, C; Chitty, A

    1975-07-01

    This paper briefly considers some of the factors which must be balanced in the selection of a boiler tube material for a Civil Fast Reactor. The merits and possible demerits of low alloy ferritic steels and the austenitic Alloy 800 are compared with respect to waterside corrosion resistance, mechanical properties, fabrication and weldability and possible effects of exposure to the sodium environment under normal and fault conditions. It is pointed out that although there is operational experience of most of the materials in boiler superheater applications there is little or none in evaporative regimes. (author)

  13. Results of radiation tests at cryogenic temperature on some selected organic materials for the LHC

    International Nuclear Information System (INIS)

    Tavlet, M.; Schoenbacher, H.

    1999-01-01

    In the near future, particle accelerators and detectors as well as fusion reactors will operate at cryogenic temperatures. At temperatures as low as 2 K, the organic materials used for the insulation of the superconducting magnets and cables will be exposed to high radiation levels. In this work, a representative selection of organic materials comprising insulating films, cable insulations and epoxy-type-impregnated resins were exposed to neutron and gamma radiation of nuclear reactors, both at ambient and cryogenic temperatures, and were subsequently mechanically tested. The results show that the radiation degradation is never worse in a cryogenic fluid than it is in usual ambient conditions. (author)

  14. Safety Standard for Oxygen and Oxygen Systems: Guidelines for Oxygen System Design, Materials Selection, Operations, Storage, and Transportation

    Science.gov (United States)

    1996-01-01

    NASA's standard for oxygen system design, materials selection, operation, and transportation is presented. Minimum guidelines applicable to NASA Headquarters and all NASA Field Installations are contained.

  15. Topical study on IRS events involving foreign material intrusion in plant systems. First issue. Report of a consultants meeting. Working material

    International Nuclear Information System (INIS)

    1997-01-01

    Recent exchange of operational safety experience among countries, within the framework of the IRS, revealed a noticeable increase in incidents involving foreign material intrusion (FMI) in nuclear power plant systems. These incidents appeared to have safety impact, sometimes widespread, on many systems and components, including the reactor core, control rods, the secondary side, and other support systems such as the electrical, air, and water systems. Notwithstanding the economic penalties and the operational problems that can arise from the FMI, many events indicated severe component damages, challenges to safety systems and to fuel integrity. Difficulties encountered with the removal of foreign material present further challenges due to the long term effects of such material remaining in the system and interacting with either fuel cladding, with the potential of releasing fission products in coolant systems, or with the system pressure boundary with the potential for material wear and sudden failure of the pressure boundary. The FMI topic was, therefore, one of a number of topics that was recommended by the TCM in 1996 for investigation. A consultant meeting was held at the IAEA during the period 14-18 April 1997 to address this topic. Figs

  16. The Influence of Free Space Environment in the Mission Life Cycle: Material Selection

    Science.gov (United States)

    Edwards, David L.; Burns, Howard D.; de Groh, Kim K.

    2014-01-01

    The natural space environment has a great influence on the ability of space systems to perform according to mission design specification. Understanding the natural space environment and its influence on space system performance is critical to the concept formulation, design, development, and operation of space systems. Compatibility with the natural space environment is a primary factor in determining the functional lifetime of the space system. Space systems being designed and developed today are growing in complexity. In many instances, the increased complexity also increases its sensitivity to space environmental effects. Sensitivities to the natural space environment can be tempered through appropriate design measures, material selection, ground processing, mitigation strategies, and/or the acceptance of known risks. The design engineer must understand the effects of the natural space environment on the space system and its components. This paper will discuss the influence of the natural space environment in the mission life cycle with a specific focus on the role of material selection.

  17. Effect of material selection and background impurity on interface property and resulted CIP-GMR performance

    International Nuclear Information System (INIS)

    Peng Xilin; Morrone, Augusto; Nikolaev, Konstantin; Kief, Mark; Ostrowski, Mark

    2009-01-01

    In this paper, we investigated the effect of background base pressure, wafer-transferring time between process modules, and stack layer material selection on the current-in-plane giant magneto-resistive (CIP-GMR) interface properties and the resulted CIP-GMR performance. Experimental results showed that seed layer/AFM interface, AFM/pinned layer (PL) interface, pinned layer/Ru interface, and reference layer (RL)/Cu spacer interface are among the most critical ones for a CIP-GMR device. By reducing the background impurity level (water moisture and oxygen), optimizing the wafer process flow sequence, and careful stack-layer material selection, such critical interfaces in a CIP-GMR device can be preserved. Consequently, a much robust GMR performance control can be achieved.

  18. Corrosion test plan to guide canister material selection and design for a tuff repository

    International Nuclear Information System (INIS)

    McCright, R.D.; van Konynenburg, R.A.; Ballou, L.B.

    1983-11-01

    Corrosion rates and the mode of corrosion attack form a most important basis for selection of canister materials and design of a nuclear waste package. Type 304L stainless steel was selected as the reference material for canister fabrication because of its generally excellent corrosion resistance in water, steam and air. However, 304L may be susceptible to localized and stress-assisted forms of corrosion under certain conditions. Alternative alloys are also investigated; these alloys were chosen because of their improved resistance to these forms of corrosion. The fabrication and welding processes, as well as the glass pouring operation for defense and commercial high-level wastes, may influence the susceptibility of the canister to localized and stress forms of corrosion. 12 references, 2 figures, 4 tables

  19. Material Selection for Cable Gland to Improved Reliability of the High-hazard Industries

    Science.gov (United States)

    Vashchuk, S. P.; Slobodyan, S. M.; Deeva, V. S.; Vashchuk, D. S.

    2018-01-01

    The sealed cable glands (SCG) are available to ensure safest connection sheathed single wire for the hazard production facility (nuclear power plant and others) the same as pilot cable, control cables, radio-frequency cables et al. In this paper, we investigate the specifics of the material selection of SCG with the express aim of hazardous man-made facility. We discuss the safe working conditions for cable glands. The research indicates the sintering powdered metals cables provide the reliability growth due to their properties. A number of studies have demonstrated the verification of material selection. On the face of it, we make findings indicating that double glazed sealed units could enhance reliability. We had evaluated sample reliability under fire conditions, seismic load, and pressure containment failure. We used the samples mineral insulated thermocouple cable.

  20. Betsy Pugel, Tiny houses: Planetary protection-focused materials selection for spaceflight hardware surfaces

    OpenAIRE

    Schriml, Lynn

    2017-01-01

    Betsy Pugel, National Aeronautics and Space Administration Tiny houses: Planetary protection-focused materials selection for spaceflight hardware surfacesOn October 10-12th, 2017 the Alfred P. Sloan Foundation and The National Academies of Sciences, Engineering and Medicine co-hosting MoBE 2017 (Microbiology of the Built Environment Research and Applications Symposium) at the National Academy of Sciences Building to present the current state-of-the-science in understanding the formation and ...

  1. Iodine-labelling of albumin and fibrinogen and application in selecting implantable material-titanium oxide

    International Nuclear Information System (INIS)

    Liu Fangyan; Zhou Meiying; Zhang Feng

    1998-01-01

    Human serum albumin and fibrinogen were successfully labelled with 125 I. The labelled proteins were further applied to carry out a background study on the selection of the blood-compatible materials. The protein adsorption of four kinds of titanium oxide film was determined and compared. It was found that Sample B can adsorb more albumin and less fibrinogen than other three samples and hold the adsorbed albumin most stably

  2. Automating Risk Assessments of Hazardous Material Shipments for Transportation Routes and Mode Selection

    International Nuclear Information System (INIS)

    Dolphin, Barbara H.; Richins, William D.; Novascone, Stephen R.

    2010-01-01

    The METEOR project at Idaho National Laboratory (INL) successfully addresses the difficult problem in risk assessment analyses of combining the results from bounding deterministic simulation results with probabilistic (Monte Carlo) risk assessment techniques. This paper describes a software suite designed to perform sensitivity and cost/benefit analyses on selected transportation routes and vehicles to minimize risk associated with the shipment of hazardous materials. METEOR uses Monte Carlo techniques to estimate the probability of an accidental release of a hazardous substance along a proposed transportation route. A METEOR user selects the mode of transportation, origin and destination points, and charts the route using interactive graphics. Inputs to METEOR (many selections built in) include crash rates for the specific aircraft, soil/rock type and population densities over the proposed route, and bounding limits for potential accident types (velocity, temperature, etc.). New vehicle, materials, and location data are added when available. If the risk estimates are unacceptable, the risks associated with alternate transportation modes or routes can be quickly evaluated and compared. Systematic optimizing methods will provide the user with the route and vehicle selection identified with the lowest risk of hazardous material release. The effects of a selected range of potential accidents such as vehicle impact, fire, fuel explosions, excessive containment pressure, flooding, etc. are evaluated primarily using hydrocodes capable of accurately simulating the material response of critical containment components. Bounding conditions that represent credible accidents (i.e; for an impact event, velocity, orientations, and soil conditions) are used as input parameters to the hydrocode models yielding correlation functions relating accident parameters to component damage. The Monte Carlo algorithms use random number generators to make selections at the various decision

  3. Determination of trace amounts of uranium in silicate materials by means of neutron activation analysis involving rapid radiochemical separation

    International Nuclear Information System (INIS)

    Ebihara, M.; Tomura, Kenji; Masutani, M.

    1987-01-01

    Uranium is determined in silicate materials such as standard rocks and a meteorite by radiochemical neutron activation analysis. The gamma-ray intensity of 239 U was measured with a planar type pure germanium detector system. The obtained data are mostly consistent with the literature values. Compared with a non-destructive method, the present method was found to improve the sensitivity by at least a factor of ten. Several errors which might be involved in the authors' RNAA procedures were examined and their degrees were evaluated. (author)

  4. An Elementary Overview of the Selection of Materials for Service in Oxygen-Enriched Environments

    Science.gov (United States)

    Davis, Samuel Eddie

    2012-01-01

    The process for selecting materials for use in oxygen or oxygen-enriched environments is one that continues to be investigated by many industries due to the importance to those industries of oxygen systems. There are several excellent resources available to assist oxygen systems design engineers and end-users, with the most comprehensive being ASTM MNL-36, Safe Use of Oxygen and Oxygen Systems: Handbook for Design, Operation and Maintenance, 2nd Edition. ASTM also makes available several standards for oxygen systems. However, the ASTM publications are extremely detailed, and typically designed for professionals who already possess a working knowledge of oxygen systems. No notable resource exists, whether an ASTM or other organizational publication, which can be used to educate engineers or technicians who have no prior knowledge of the nuances of oxygen system design and safety. This paper will fill the void for information needed by organizations that design or operate oxygen systems. The information in this paper is not new information, but is a concise and easily understood summary of selecting materials for oxygen systems. This paper will serve well as an employee s first introduction to oxygen system materials selection, and probably the employee s first introduction to ASTM.

  5. Generation IV and transmutation materials (GETMAT) project: First assessment of selected results

    International Nuclear Information System (INIS)

    Fazio, Concetta; Serrano, Marta; Gessi, Alessandro; Henry, Jean; Malerba, Lorenzo

    2015-01-01

    The Generation IV and Transmutation Material (GETMAT) project has been initiated within the 7. EURATOM framework programme with the objective to support the development of innovative reactor designs. Emphasis has been put on the investigation, both in the theoretical and experimental domains, of selected material properties that are cross-cutting among the various Generation IV and Transmutation systems. The selection of the properties to be investigated has been performed by identifying relevant conditions of key components as cores and primary systems. Moreover, taking into account the envisaged conditions of these components it turned out that innovative materials might be a better choice with respect to conventional nuclear grade steels. Therefore, ODS alloys and 9-12 Cr Ferritic/Martensitic (F/M) steels have been selected as reference for the GETMAT project. The R and D activities have been focused on basic characterisation of ODS alloys produced ad hoc for the project and on an extensive PIE programme of F/M steels irradiated in previous programmes. Finally, first principle modelling studies to explain irradiation hardening and embrittlement of F/M alloys were an additional important task. The objective of this manuscript is to make a first assessment of the results obtained within GETMAT. (authors)

  6. Stress corrosion cracking susceptibility of selected materials for steam plant bolting applications

    Energy Technology Data Exchange (ETDEWEB)

    Mayer, P.; Noga, J.O.; Ogundele, G.

    1996-12-01

    The incidence of alloy steel bolting failure in nuclear and fossil fired generating plants was discussed. The problem manifests itself in the form of intergranular stress corrosion cracking. A study was conducted to rank the susceptibility of three materials (Alloy AISI, type 4140, Alloy ASTM A564-92AXM 13 and Inconel 718) to stress corrosion cracking and to determine threshold stress intensity factors of currently used and alternate alloys in service environments typically encountered in steam generating utility plants. Although most alloy steel bolting failures have involved Cr-Mo, failures have also been reported for all the above mentioned materials. Attempts to minimize the occurrence of stress corrosion cracking have involved a ban on molybdenum disulphide, limiting bolt tightening torque and placing an upper limit on bolt hardness, and by correlation on tensile strength. Slow strain rate and wedge opening-loading specimen tests were used to evaluate commonly used and superior alternative bolting materials. Electrochemical polarization tests were also conducted. Threshold stresses in a H{sub 2}S environment were determined according to NACE standard TM-01-77. Results showed that, to a certain degree, all tested materials were susceptible to stress corrosion cracking. They ranked as follows from best to worst performance: (1) the Inconel 718, (2) alloy SM 13, and (3) alloy 4140. 9 refs., 20 tabs., 34 figs.

  7. Novel porous carbon materials with ultrahigh nitrogen contents for selective CO 2 capture

    KAUST Repository

    Zhao, Yunfeng; Zhao, Lan; Yao, Kexin; Yang, Yang; Zhang, Qiang; Han, Yu

    2012-01-01

    Nitrogen-doped carbon materials were prepared by a nanocasting route using tri-continuous mesoporous silica IBN-9 as a hard template. Rationally choosing carbon precursors and carefully controlling activation conditions result in an optimized material denoted as IBN9-NC1-A, which possesses a very high nitrogen doping concentration (∼13 wt%) and a large surface area of 890 m 2 g -1 arising from micropores (<1 nm). It exhibits an excellent performance for CO 2 adsorption over a wide range of CO 2 pressures. Specifically, its equilibrium CO 2 adsorption capacity at 25 °C reaches up to 4.50 mmol g -1 at 1 bar and 10.53 mmol g -1 at 8 bar. In particular, it shows a much higher CO 2 uptake at low pressure (e.g. 1.75 mmol g -1 at 25 °C and 0.2 bar) than any reported carbon-based materials, owing to its unprecedented nitrogen doping level. The high nitrogen contents also give rise to significantly enhanced CO 2/N 2 selectivities (up to 42), which combined with the high adsorption capacities, make these new carbon materials promising sorbents for selective CO 2 capture from power plant flue gas and other relevant applications. © 2012 The Royal Society of Chemistry.

  8. Material selection for elastic energy absorption in origami-inspired compliant corrugations

    International Nuclear Information System (INIS)

    Tolman, Sean S; Delimont, Isaac L; Howell, Larry L; Fullwood, David T

    2014-01-01

    Elastic absorption of kinetic energy and distribution of impact forces are required in many applications. Recent attention to the potential for using origami in engineering may provide new methods for energy absorption and force distribution. A three-stage strategy is presented for selecting materials for such origami-inspired designs that can deform to achieve a desired motion without yielding, absorb elastic strain energy, and be lightweight or cost effective. Two material indices are derived to meet these requirements based on compliant mechanism theory. Finite element analysis is used to investigate the effects of the material stiffness in the Miura-ori tessellation on its energy absorption and force distribution characteristics compared with a triangular wave corrugation. An example is presented of how the method can be used to select a material for a general energy absorption application of the Miura-ori. Whereas the focus of this study is the Miura-ori tessellation, the methods developed can be applied to other tessellated patterns used in energy absorbing or force distribution applications. (paper)

  9. Guidelines for selecting preferred highway routes for highway-route-controlled quantity shipments of radioactive materials

    International Nuclear Information System (INIS)

    1989-01-01

    The document presents guidelines for use by State officials in selecting preferred routes for highway route controlled quantity shipments of radioactive materials. A methodology for analyzing and comparing safety factors of alternative routes is described. Technical information on the impacts of radioactive material transportation needed to apply the methodology is also presented. Application of the methodology will identify the route (or set of routes) that minimizes the radiological impacts from shipments of these radioactive materials within a given State. Emphasis in the document is on practical application of the methodology. Some details of the derivation of the methods and data are presented in the appendices. All references in the body of the report can be found listed in the Bibliography (Appendix F)

  10. Evaluation of functional substances in the selected food materials for space agriculture

    Science.gov (United States)

    Tomita-Yokotani, Kaori; Kimura, Yasuko; Yamashita, Masamichi; Kimura, Shunta; Sato, Seigo; Katoh, Hiroshi; Abe, Yusuke; Ajioka, Reiko

    We have been studying the useful life-support system in closed bio-ecosystem for space agriculture. We have already proposed the several species as food material, such as Nostoc sp. HK-01 and Prunnus sp., cyanobacterium and Japanese cherry tree, respectively. The cyanobacterium, Nostoc sp Hk-01, has high tolerances to several space environment. Furthermore, the woody plant materials have useful utilization elements in our habitation environment. The studies of woody plants under a space-environment in the vegetable kingdom have a high contribution to the study of various and exotic environmental responses, too. We have already found that they can produce the important functional substances for human. Here, we will show the evaluation of functional substances in the selected food materials under the possible conditions for space agriculture after cooking.

  11. Selection and durability of seal materials for a bedded salt repository: preliminary studies

    International Nuclear Information System (INIS)

    Roy, D.M.; Grutzeck, M.W.; Wakeley, L.D.

    1983-11-01

    This report details preliminary results of both experimental and theoretical studies of cementitious seal materials for use in a proposed nuclear waste repository in bedded salt. Effects of changes in bulk composition and environment upon phase stability and physical/mechanical properties have been evaluated for more than 25 formulations. Bonding and interfacial characteristics of the region between host rock and seal material or concrete aggregate and cementitious matrix for selected formulations have been studied. Compatibilities of clays and zeolites in brines typical of the SE New Mexico region have been investigated, and their stabilities reviewed. Results of these studies have led to the conclusion that cementitious materials can be formulated which are compatible with the major rock types in a bedded salt repository environment. Strengths are more than adequate, permeabilities are consistently very low, and elastic moduli generally increase only very slightly with time. Seal formulation guidelines and recommendations for present and future work are presented. 73 references, 25 figures, 61 tables

  12. Survey and analysis of materials research and development at selected federal laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Reed, J.E.; Fink, C.R.

    1984-04-01

    This document presents the results of an effort to transfer existing, but relatively unknown, materials R and D from selected federal laboratories to industry. More specifically, recent materials-related work at seven federal laboratories potentially applicable to improving process energy efficiency and overall productiviy in six energy-intensive manufacturing industries was evaluated, catalogued, and distributed to industry representatives to gauge their reaction. Laboratories surveyed include: Air Force Wright Aeronautical Laboratories Material Laboratory (AFWAL). Pacific Northwest Laboratory (PNL), National Aeronautics and Space Administration Marshall Flight Center (NASA Marshall), Oak Ridge National Laboratory (ORNL), Brookhaven National Laboratory (BNL), Idaho National Engineering Laboratory (INEL), and Jet Propulsion Laboratory (JPL). Industries included in the effort are: aluminum, cement, paper and allied products, petroleum, steel and textiles.

  13. LEARNING MATERIALS SELECTION FOR DIFFERENTIATED INSTRUCTION OF ENGLISH FOR SPECIFIC PURPOSES OF FUTURE PROFESSIONALS IN THE FIELD OF INFORMATION TECHNOLOGY

    Directory of Open Access Journals (Sweden)

    Oksana Synekop

    2017-09-01

    Full Text Available In conditions of differentiation the learning materials selection will optimize the training English for Specific Purposes of the future professionals in the field of information technology at university level. The purpose of the article is to define the basic unit of learning material, the factors of influence on the learning material selection, principles, criteria and the procedure of learning material selection in this paper. Reviewing the scientific achievements in the learning material selection in teaching English has become a basis for defining the factors of influence, principles and criteria in the research. The basic unit of learning material (learning English text for professional purposes is outlined. The factors of influence and principles (correspondence of learning materials to professional interests and needs of information technology students; necessary ability and accessibility; regarding the linguistic and stylistic necessity and sufficiency; availability of Internet sources information of the learning material selection are defined. Also, the qualitative criteria (authenticity; professional significance, relevance and informativeness; conformity of foreign language level and intellectual development of students; variety of genres and forms of speech, their sufficient filling by linguistic material; coherence, integrity, consistency, semantic completeness; topic conformity; situation conformity; unlimited access, reliability and exemplarity of Internet sources and the quantitative criteria (the amount of material of the learning material selection are highlighted. The process of English for Specific Purposes material selection (defining the disciplines of different cycles; defining spheres and related topics; outlining situations, communicative roles and intentions of professional communication; specifying the sources of selection; evaluating the texts; analysis of the knowledge, skills and sub-skills required for the

  14. Reexamination of the source material of acid igneous rocks, based on the selected Sr isotopic data

    International Nuclear Information System (INIS)

    Kagami, Hiroo; Shuto, Kenji; Gorai, Masao

    1975-01-01

    The relation between the ages and the initial strontium isotopic compositions obtained from acid igneous rocks by the whole-rock isochron method is re-examined, on the basis of the selected data. The points based on the data having high values of standard deviation (on the isochrons) show considerable scattering. This is probably ascribed to admixture of sialic materials, or secondary alteration and other geologic causes. The points based on the data having lower values of standard deviation (sigma value: 0.0001 - 0.0019), on the other hand, are evidently plotted within a narrow region just above the presumed Sr evolutional region of the source material of oceanic tholeiites. It is noteworthy that the former region meets the latter region at an earlier stage of the evolutional history of the earth (about 40 x 10 8 yrs. ago or older). It may be conceivable that the former region is the Sr evolutional region of the source material of acid igneous rocks. Considering from the inclination of the above Sr evolutional region, the source material of most of acid igneous rocks may possibly be a certain basic material, chemically similar to the continental tholeiitic basalts or basaltic andesites. On the other hand, the source material of a few acid igneous rocks with low initial strontium isotopic ratios may be a certain basic material resembling the oceanic tholeiites. Another possibility is that these acid igneous rocks and oceanic tholeiites may have been formed, under different physical conditions, directly from a certain common source material presumably of peridotitic composition. (auth.)

  15. Bowtie filters for dedicated breast CT: Analysis of bowtie filter material selection

    Energy Technology Data Exchange (ETDEWEB)

    Kontson, Kimberly, E-mail: Kimberly.Kontson@fda.hhs.gov; Jennings, Robert J. [Department of Bioengineering, University of Maryland, College Park, Maryland 20742 and Division of Imaging and Applied Mathematics, Office of Science and Engineering Laboratories, Center for Devices and Radiological Health, U.S. Food and Drug Administration, 10903 New Hampshire Avenue, Silver Spring, Maryland 20993 (United States)

    2015-09-15

    Purpose: For a given bowtie filter design, both the selection of material and the physical design control the energy fluence, and consequently the dose distribution, in the object. Using three previously described bowtie filter designs, the goal of this work is to demonstrate the effect that different materials have on the bowtie filter performance measures. Methods: Three bowtie filter designs that compensate for one or more aspects of the beam-modifying effects due to the differences in path length in a projection have been designed. The nature of the designs allows for their realization using a variety of materials. The designs were based on a phantom, 14 cm in diameter, composed of 40% fibroglandular and 60% adipose tissue. Bowtie design #1 is based on single material spectral matching and produces nearly uniform spectral shape for radiation incident upon the detector. Bowtie design #2 uses the idea of basis-material decomposition to produce the same spectral shape and intensity at the detector, using two different materials. With bowtie design #3, it is possible to eliminate the beam hardening effect in the reconstructed image by adjusting the bowtie filter thickness so that the effective attenuation coefficient for every ray is the same. Seven different materials were chosen to represent a range of chemical compositions and densities. After calculation of construction parameters for each bowtie filter design, a bowtie filter was created using each of these materials (assuming reasonable construction parameters were obtained), resulting in a total of 26 bowtie filters modeled analytically and in the PENELOPE Monte Carlo simulation environment. Using the analytical model of each bowtie filter, design profiles were obtained and energy fluence as a function of fan-angle was calculated. Projection images with and without each bowtie filter design were also generated using PENELOPE and reconstructed using FBP. Parameters such as dose distribution, noise uniformity

  16. Bowtie filters for dedicated breast CT: Analysis of bowtie filter material selection

    International Nuclear Information System (INIS)

    Kontson, Kimberly; Jennings, Robert J.

    2015-01-01

    Purpose: For a given bowtie filter design, both the selection of material and the physical design control the energy fluence, and consequently the dose distribution, in the object. Using three previously described bowtie filter designs, the goal of this work is to demonstrate the effect that different materials have on the bowtie filter performance measures. Methods: Three bowtie filter designs that compensate for one or more aspects of the beam-modifying effects due to the differences in path length in a projection have been designed. The nature of the designs allows for their realization using a variety of materials. The designs were based on a phantom, 14 cm in diameter, composed of 40% fibroglandular and 60% adipose tissue. Bowtie design #1 is based on single material spectral matching and produces nearly uniform spectral shape for radiation incident upon the detector. Bowtie design #2 uses the idea of basis-material decomposition to produce the same spectral shape and intensity at the detector, using two different materials. With bowtie design #3, it is possible to eliminate the beam hardening effect in the reconstructed image by adjusting the bowtie filter thickness so that the effective attenuation coefficient for every ray is the same. Seven different materials were chosen to represent a range of chemical compositions and densities. After calculation of construction parameters for each bowtie filter design, a bowtie filter was created using each of these materials (assuming reasonable construction parameters were obtained), resulting in a total of 26 bowtie filters modeled analytically and in the PENELOPE Monte Carlo simulation environment. Using the analytical model of each bowtie filter, design profiles were obtained and energy fluence as a function of fan-angle was calculated. Projection images with and without each bowtie filter design were also generated using PENELOPE and reconstructed using FBP. Parameters such as dose distribution, noise uniformity

  17. Ultrahigh and Selective SO2 Uptake in Inorganic Anion-Pillared Hybrid Porous Materials.

    Science.gov (United States)

    Cui, Xili; Yang, Qiwei; Yang, Lifeng; Krishna, Rajamani; Zhang, Zhiguo; Bao, Zongbi; Wu, Hui; Ren, Qilong; Zhou, Wei; Chen, Banglin; Xing, Huabin

    2017-07-01

    The efficient capture of SO 2 is of great significance in gas-purification processes including flue-gas desulfurization and natural-gas purification, but the design of porous materials with high adsorption capacity and selectivity of SO 2 remains very challenging. Herein, the selective recognition and dense packing of SO 2 clusters through multiple synergistic host-guest and guest-guest interactions by controlling the pore chemistry and size in inorganic anion (SiF 6 2- , SIFSIX) pillared metal-organic frameworks is reported. The binding sites of anions and aromatic rings in SIFSIX materials grasp every atom of SO 2 firmly via S δ+ ···F δ- electrostatic interactions and O δ- ···H δ+ dipole-dipole interactions, while the guest-guest interactions between SO 2 molecules further promote gas trapping within the pore space, which is elucidated by first-principles density functional theory calculations and powder X-ray diffraction experiments. These interactions afford new benchmarks for the highly efficient removal of SO 2 from other gases, even if at a very low SO 2 concentration. Exceptionally high SO 2 capacity of 11.01 mmol g -1 is achieved at atmosphere pressure by SIFSIX-1-Cu, and unprecedented low-pressure SO 2 capacity is obtained in SIFSIX-2-Cu-i (4.16 mmol g -1 SO 2 at 0.01 bar and 2.31 mmol g -1 at 0.002 bar). More importantly, record SO 2 /CO 2 selectivity (86-89) and excellent SO 2 /N 2 selectivity (1285-3145) are also achieved. Experimental breakthrough curves further demonstrate the excellent performance of these hybrid porous materials in removing low-concentration SO 2 . © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Concept selection of car bumper beam with developed hybrid bio-composite material

    International Nuclear Information System (INIS)

    Davoodi, M.M.; Sapuan, S.M.; Ahmad, D.; Aidy, A.; Khalina, A.; Jonoobi, Mehdi

    2011-01-01

    Highlights: → We simulate the low impact test by Abaqus Ver16R9 using the same material model. → Six different weighted criteria were discussed to nominate the best concept. → Double Hat Profile showed the best concept to fulfil the defined PDS. → Geometric parameters may overcome the weak inherent properties of bio composite. → Toughened bio-composite material may employ in structural automotive components. -- Abstract: Application of natural fibre composites is going to increase in different areas caused by environmental, technical and economic advantages. However, their low mechanical properties have limited their particular application in automotive structural components. Hybridizations with other reinforcements or matrices can improve mechanical properties of natural fibre composite. Moreover, geometric optimizations have a significant role in structural strength improvement. This study focused on selecting the best geometrical bumper beam concept to fulfill the safety parameters of the defined product design specification (PDS). The mechanical properties of developed hybrid composite material were considered in different bumper beam concepts with the same frontal curvature, thickness, and overall dimensions. The low-speed impact test was simulated under the same conditions in Abaqus V16R9 software. Six weighted criteria, which were deflection, strain energy, mass, cost, easy manufacturing, and the rib possibility were analyzed to form an evaluation matrix. Topsis method was employed to select the best concept. It is concluded that double hat profile (DHP) with defined material model can be used for bumper beam of a small car. In addition, selected concept can be strengthened by adding reinforced ribs or increasing the thickness of the bumper beam to comply with the defined PDS.

  19. Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2002-01-01

    1.1 This guide summarizes the standard test methods available for determining physical and mechanical characteristics of interlayer materials used in multi-ply aerospace transparent enclosures. 1.2 Interlayer materials are used to laminate glass-to-glass, glass-to-plastic, and plastic-to-plastic. Interlayer materials are basically transparent adhesives with high-quality optical properties. They can also serve as an energy absorbing medium, a fail-safe membrane to contain cockpit pressure and to prevent entry of impact debris; a strain insulator to accommodate different thermal expansion rates of members being laminated and as an adherent to prevent spalling of inner surface ply material fragments. The relative importance of an interlayer characteristic will be a function of the prime use it serves in its particular application. 1.3 This guide, as a summary of various methods in Section 2, is intended to facilitate the selection of tests that can be applied to interlayer materials. 1.4 The test methods list...

  20. Reduced Graphene Oxide-Gold Nanoparticle Nanoframework as a Highly Selective Separation Material for Aflatoxins.

    Science.gov (United States)

    Guo, Wenbo; Wu, Lidong; Fan, Kai; Nie, Dongxia; He, Weijing; Yang, Junhua; Zhao, Zhihui; Han, Zheng

    2017-11-03

    Graphene-based materials have been studied in many applications, owing to the excellent electrical, mechanical, and thermal properties of graphene. In the current study, an environmentally friendly approach to the preparation of a reduced graphene oxide-gold nanoparticle (rGO-AuNP) nanocomposite was developed by using L-cysteine and vitamin C as reductants under mild reaction conditions. The rGO-AuNP material showed a highly selective separation ability for 6 naturally occurring aflatoxins, which are easily adsorbed onto traditional graphene materials but are difficult to be desorbed. The specificity of the nanocomposite was evaluated in the separation of 6 aflatoxin congeners (aflatoxin B1, aflatoxin B2, aflatoxin G1, aflatoxin G2, aflatoxin M1 and aflatoxin M2) from 23 other biotoxins (including, ochratoxin A, citrinin, and deoxynivalenol). The results indicated that this material was specific for separating aflatoxin congeners. The synthesized material was further validated by determining the recovery (77.6-105.0%), sensitivity (limit of detection in the range of 0.05-0.21 μg kg -1 ), and precision (1.5-11.8%), and was then successfully applied to the separation of aflatoxins from real-world maize, wheat and rice samples.

  1. Sustainable manufacturing: Effect of material selection and design on the environmental impact in the manufacturing process

    International Nuclear Information System (INIS)

    Harun, Mohd Hazwan Syafiq; Salaam, Hadi Abdul; Taha, Zahari

    2013-01-01

    The environmental impact of a manufacturing process is also dependent on the selection of the material and design of a product. This is because the manufacturing of a product is directly connected to the amount of carbon emitted in consuming the electrical energy for that manufacturing process. The difference in the general properties of materials such as strength, hardness and impact will have significant effect on the power consumption of the machine used to complete the product. In addition the environmental impact can also be reduced if the proposed designs use less material. In this study, an LCA tool called Eco-It is used. Evaluate the environmental impact caused by manufacturing simple jig. A simple jig with 4 parts was used as a case study. Two experiments were carried out. The first experiment was to study the environmental effects of different material, and the second experiment was to study the environmental impact of different design. The materials used for the jig are Aluminium and mild steel. The results showed a decrease in the rate of carbon emissions by 60% when Aluminium is use instead from mild steel, and a decrease of 26% when the-design is modified

  2. Dual-Material Electron Beam Selective Melting: Hardware Development and Validation Studies

    Directory of Open Access Journals (Sweden)

    Chao Guo

    2015-03-01

    Full Text Available Electron beam selective melting (EBSM is an additive manufacturing technique that directly fabricates three-dimensional parts in a layerwise fashion by using an electron beam to scan and melt metal powder. In recent years, EBSM has been successfully used in the additive manufacturing of a variety of materials. Previous research focused on the EBSM process of a single material. In this study, a novel EBSM process capable of building a gradient structure with dual metal materials was developed, and a powder-supplying method based on vibration was put forward. Two different powders can be supplied individually and then mixed. Two materials were used in this study: Ti6Al4V powder and Ti47Al2Cr2Nb powder. Ti6Al4V has excellent strength and plasticity at room temperature, while Ti47Al2Cr2Nb has excellent performance at high temperature, but is very brittle. A Ti6Al4V/Ti47Al2Cr2Nb gradient material was successfully fabricated by the developed system. The microstructures and chemical compositions were characterized by optical microscopy, scanning microscopy, and electron microprobe analysis. Results showed that the interface thickness was about 300 μm. The interface was free of cracks, and the chemical compositions exhibited a staircase-like change within the interface.

  3. Selection Criteria and Methods for Testing Different Surface Materials for Contact Frying Processes

    DEFF Research Database (Denmark)

    Ashokkumar, Saranya

    Inner surfaces of industrial process equipment for food are often coated to give the surfaces particular properties with respect to adhesion and cleanability. Existing coating materials (PTFE (Teflon®) or silicone based polymers) suffer from drawbacks when used in contact frying, because these co...... surface materials for contact frying processes. The surfaces selected for this purpose cover a wide spectrum of materials that range from hydrophobic to hydrophilic materials. The different surface materials investigated include stainless steel (reference), aluminium (Al Mg 5754), PTFE......, an experimental rig has been constructed which enabled a controlled fouling of different coatings on steel and aluminium substrates under realistic frying conditions. A subjective rating procedure was employed for screening different surfaces according to their non-stick properties when used for frying of a model...... defects and surface roughness play a significant role. The wear resistance of the coatings was tested by performing abrasive wear experiments. The ceramic coatings: TiAlN and ZrN were found to show the best wear resistance properties. The experiments also revealed the poor wear resistance of stainless...

  4. Piezoelectric materials selection for sensor applications using finite element and multiple attribute decision-making approaches

    Directory of Open Access Journals (Sweden)

    Anuruddh Kumar

    2015-03-01

    Full Text Available This paper examines the selection and performance evaluation of a variety of piezoelectric materials for cantilever-based sensor applications. The finite element analysis method is implemented to evaluate the relative importance of materials properties such as Young's Modulus (E, piezoelectric stress constants (e31, dielectric constant (ε and Poisson's ratio (υ for cantilever-based sensor applications. An analytic hierarchy process (AHP is used to assign weights to the properties that are studied for the sensor structure under study. A technique for order preference by similarity to ideal solution (TOPSIS is used to rank the performance of the piezoelectric materials in the context of sensor voltage outputs. The ranking achieved by the TOPSIS analysis is in good agreement with the results obtained from finite element method simulation. The numerical simulations show that K0.5Na0.5NbO3–LiSbO3 (KNN–LS materials family is important for sensor application. Young's modulus (E is most influencing material's property followed by piezoelectric constant (e31, dielectric constant (ε and Poisson's ratio (υ for cantilever-based piezoelectric sensor applications.

  5. Cost-driven materials selection criteria for redox flow battery electrolytes

    Science.gov (United States)

    Dmello, Rylan; Milshtein, Jarrod D.; Brushett, Fikile R.; Smith, Kyle C.

    2016-10-01

    Redox flow batteries show promise for grid-scale energy storage applications but are presently too expensive for widespread adoption. Electrolyte material costs constitute a sizeable fraction of the redox flow battery price. As such, this work develops a techno-economic model for redox flow batteries that accounts for redox-active material, salt, and solvent contributions to the electrolyte cost. Benchmark values for electrolyte constituent costs guide identification of design constraints. Nonaqueous battery design is sensitive to all electrolyte component costs, cell voltage, and area-specific resistance. Design challenges for nonaqueous batteries include minimizing salt content and dropping redox-active species concentration requirements. Aqueous battery design is sensitive to only redox-active material cost and cell voltage, due to low area-specific resistance and supporting electrolyte costs. Increasing cell voltage and decreasing redox-active material cost present major materials selection challenges for aqueous batteries. This work minimizes cost-constraining variables by mapping the battery design space with the techno-economic model, through which we highlight pathways towards low price and moderate concentration. Furthermore, the techno-economic model calculates quantitative iterations of battery designs to achieve the Department of Energy battery price target of 100 per kWh and highlights cost cutting strategies to drive battery prices down further.

  6. Stock selection of high-dose-irradiation-resistant materials for filter press under high-dose irradiation operation

    International Nuclear Information System (INIS)

    Ishiyama, Shintaro; Minami, Mamoru; Hara, Kouji; Yamashita, Manabu

    2015-01-01

    In a volume reduction process for the decontamination of contained soil, the performance degradation of a filter press is expected owing to material deterioration under high-dose irradiation. Eleven-stock selection of candidate materials including polymers, fibers and rubbers for the filter press was conducted to achieve a high performance of volume reduction of contaminated soil and the following results were derived. Crude rubber and nylon were selected as prime candidates for packing, diaphragm and filter plate materials. Polyethylene was also selected as a prime candidate for the filter cloth material. (author)

  7. Screening tests for hazard classification of complex waste materialsSelection of methods

    International Nuclear Information System (INIS)

    Weltens, R.; Vanermen, G.; Tirez, K.; Robbens, J.; Deprez, K.; Michiels, L.

    2012-01-01

    In this study we describe the development of an alternative methodology for hazard characterization of waste materials. Such an alternative methodology for hazard assessment of complex waste materials is urgently needed, because the lack of a validated instrument leads to arbitrary hazard classification of such complex waste materials. False classification can lead to human and environmental health risks and also has important financial consequences for the waste owner. The Hazardous Waste Directive (HWD) describes the methodology for hazard classification of waste materials. For mirror entries the HWD classification is based upon the hazardous properties (H1–15) of the waste which can be assessed from the hazardous properties of individual identified waste compounds or – if not all compounds are identified – from test results of hazard assessment tests performed on the waste material itself. For the latter the HWD recommends toxicity tests that were initially designed for risk assessment of chemicals in consumer products (pharmaceuticals, cosmetics, biocides, food, etc.). These tests (often using mammals) are not designed nor suitable for the hazard characterization of waste materials. With the present study we want to contribute to the development of an alternative and transparent test strategy for hazard assessment of complex wastes that is in line with the HWD principles for waste classification. It is necessary to cope with this important shortcoming in hazardous waste classification and to demonstrate that alternative methods are available that can be used for hazard assessment of waste materials. Next, by describing the pros and cons of the available methods, and by identifying the needs for additional or further development of test methods, we hope to stimulate research efforts and development in this direction. In this paper we describe promising techniques and argument on the test selection for the pilot study that we have performed on different

  8. New sorbent materials for selective extraction of cocaine and benzoylecgonine from human urine samples.

    Science.gov (United States)

    Bujak, Renata; Gadzała-Kopciuch, Renata; Nowaczyk, Alicja; Raczak-Gutknecht, Joanna; Kordalewska, Marta; Struck-Lewicka, Wiktoria; Waszczuk-Jankowska, Małgorzata; Tomczak, Ewa; Kaliszan, Michał; Buszewski, Bogusław; Markuszewski, Michał J

    2016-02-20

    An increase in cocaine consumption has been observed in Europe during the last decade. Benzoylecgonine, as a main urinary metabolite of cocaine in human, is so far the most reliable marker of cocaine consumption. Determination of cocaine and its metabolite in complex biological samples as urine or blood, requires efficient and selective sample pretreatment. In this preliminary study, the newly synthesized sorbent materials were proposed for selective extraction of cocaine and benzoylecgonine from urine samples. Application of these sorbent media allowed to determine cocaine and benzoylecgonine in urine samples at the concentration level of 100ng/ml with good recovery values as 81.7%±6.6 and 73.8%±4.2, respectively. The newly synthesized materials provided efficient, inexpensive and selective extraction of both cocaine and benzoylecgonine from urine samples, which can consequently lead to an increase of the sensitivity of the current available screening diagnostic tests. Copyright © 2015 Elsevier B.V. All rights reserved.

  9. Scarab/Saffron Development Project Case study: Material Selection Criteria for the Monoethylene Glycol Recovery Package

    International Nuclear Information System (INIS)

    Moussa, A.M.; Habib, S.; Shinaishin, A.

    2004-01-01

    MEG Recovery Unit for Scarab/Saffron development project is the first application in gas production. The Mono Ethylene Glycol Recovery Unit (MEG) recovers MEG from Water/MEG stream and removes salts and other contaminants. MEG Recovery Unit Equipment Design Criteria were designed for two parallel trains A and B, each train is capable to treat 500 bbl MEG, 1500 bbl water and 9 ton salt. The MEG unit is a combination of two unit operations; MEG Recovery unit is normally applicable in the oil and gas industries that is applying distillation technique, while the new technology is salt treatment and handling. The MEG Unit material selection is made to be suitable for the entire design life which is 25 years, the materials for MEG Recovery Unit have been selected among the available corrosion resistance alloys, where requested by the service and ambient conditions. Therefore all. the parts of the MEG unit that are in saline service are in either (2205 duplex, AISI 316L) and in Inconel alloy 625 related to operating temperature. This case study focused at Inconel alloy 625, which is selected for salt service and their operation problem occurred during the construction and operating conditions

  10. Effect of the selected seismic energy dissipation capacity on the materials quantity for reinforced concrete walls

    Directory of Open Access Journals (Sweden)

    José Miguel Benjumea Royero

    2017-02-01

    Full Text Available Context: Regarding their design of reinforced concrete structural walls, the Colombian seismic design building code allows the engineer to select one of the three seismic energy dissipation capacity (ordinary, moderate, and special depending on the seismic hazard of the site. Despite this, it is a common practice to choose the minor requirement for the site because it is thought that selecting a higher requirement will lead to larger structural materials amounts and, therefore, cost increments.  Method: In this work, an analytical study was performed in order to determine the effect of the selected energy dissipation capacity on the quantity of materials and ductility displacement capacity of R/C walls. The study was done for a region with low seismic hazard, mainly because this permitted to explore and compare the use of the three seismic energy dissipations capacities. The effect of different parameters such as the wall total height and thickness, the tributary loaded area, and the minimum volumetric steel ratio were studied. Results: The total amount of steel required for the walls with moderate and special energy dissipation capacity corresponds, on average, to 77% and 89%, respectively, of the quantity required for walls with minimum capacity. Conclusions: it is possible to achieve reductions in the total steel required weight when adopting either moderated or special seismic energy dissipation instead of the minimum capacity.  Additionally, a significant increment in the seismic ductility displacements capacity of the wall was obtained.

  11. Phase analysis of nano-phase materials using selected area electron diffraction in the TEM

    International Nuclear Information System (INIS)

    Labar, J. L.

    2002-01-01

    In analogy to X-ray power diffraction (XRD), we are developing a method to help phase identification when examining a large number of grains simultaneously by electron diffraction. Although XRD is well established, it can not be used for small quantities of materials (volumes below 1 mm 3 ). Examining a usual TEM sample with thickness of 100 nm and using a selected area of 1 mm in diameter, the selected area electron diffraction pattern (SAED) carries information about several thousands of grains from a material with an average grain size of about 10 nm. The accuracy of XRD can not be attained by electron diffraction (ED). However, simultaneous visual observation of the nanostructure is an additional benefit of TEM (beside the small amount of needed material). The first step of the development project was the development of a computer program ('ProcessDiffraction') that processes digital versions of SAED patterns and presents them in an XRD-like form (intensity vs. scattering vector). In the present version (V2.0.3) phase identification is carried out by comparing the measured distribution to 'Markers', i.e. data of known phases. XRD data cards are used if the detailed structure of a phase is not known. Kinematic electron diffraction intensities are calculated for phases with known atomic positions (Author)

  12. A materials selection procedure for sandwiched beams via parametric optimization with applications in automotive industry

    International Nuclear Information System (INIS)

    Aly, Mohamed F.; Hamza, Karim T.; Farag, Mahmoud M.

    2014-01-01

    Highlights: • Sandwich panels optimization model. • Sandwich panels design procedure. • Study of sandwich panels for automotive vehicle flooring. • Study of sandwich panels for truck cabin exterior. - Abstract: The future of automotive industry faces many challenges in meeting increasingly strict restrictions on emissions, energy usage and recyclability of components alongside the need to maintain cost competiveness. Weight reduction through innovative design of components and proper material selection can have profound impact towards attaining such goals since most of the lifecycle energy usage occurs during the operation phase of a vehicle. In electric and hybrid vehicles, weight reduction has another important effect of extending the electric mode driving range between stops or gasoline mode. This paper adopts parametric models for design optimization and material selection of sandwich panels with the objective of weight and cost minimization subject to structural integrity constraints such as strength, stiffness and buckling resistance. The proposed design procedure employs a pre-compiled library of candidate sandwich panel material combinations, for which optimization of the layered thicknesses is conducted and the best one is reported. Example demonstration studies from the automotive industry are presented for the replacement of Aluminum and Steel panels with polypropylene-filled sandwich panel alternatives

  13. Protective Behaviour of Citizens to Transport Accidents Involving Hazardous Materials: A Discrete Choice Experiment Applied to Populated Areas nearby Waterways.

    Directory of Open Access Journals (Sweden)

    Esther W de Bekker-Grob

    Full Text Available To improve the information for and preparation of citizens at risk to hazardous material transport accidents, a first important step is to determine how different characteristics of hazardous material transport accidents will influence citizens' protective behaviour. However, quantitative studies investigating citizens' protective behaviour in case of hazardous material transport accidents are scarce.A discrete choice experiment was conducted among subjects (19-64 years living in the direct vicinity of a large waterway. Scenarios were described by three transport accident characteristics: odour perception, smoke/vapour perception, and the proportion of people in the environment that were leaving at their own discretion. Subjects were asked to consider each scenario as realistic and to choose the alternative that was most appealing to them: staying, seeking shelter, or escaping. A panel error component model was used to quantify how different transport accident characteristics influenced subjects' protective behaviour.The response was 44% (881/1,994. The predicted probability that a subject would stay ranged from 1% in case of a severe looking accident till 62% in case of a mild looking accident. All three transport accident characteristics proved to influence protective behaviour. Particularly a perception of strong ammonia or mercaptan odours and visible smoke/vapour close to citizens had the strongest positive influence on escaping. In general, 'escaping' was more preferred than 'seeking shelter', although stated preference heterogeneity among subjects for these protective behaviour options was substantial. Males were less willing to seek shelter than females, whereas elderly people were more willing to escape than younger people.Various characteristics of transport accident involving hazardous materials influence subjects' protective behaviour. The preference heterogeneity shows that information needs to be targeted differently depending on

  14. Effects of LDEF flight exposure on selected polymer matrix resin composite materials

    Science.gov (United States)

    Slemp, Wayne S.; Young, Philip R.; Witte, William G., Jr.; Shen, James Y.

    1992-01-01

    The characterization of selected graphite fiber reinforced epoxy (934 and 5208) and polysulfone (P1700) matrix resin composites materials which received over five years and nine months of exposure to the low earth orbit (LEO) environment in experiment AO134 on the Long Duration Exposure Facility is reported. The changes in mechanical properties of ultimate tensile strength and tensile modulus for exposed flight specimens are compared to the three sets of control specimens. Marked changes in surface appearance are discussed, and resin loss is reported. The chemical characterization including infrared, thermal, and selected solution property measurements showed that the molecular structure of the polymetric matrix had not changed significantly in response to this exposure.

  15. Exponential growth and selection in self-replicating materials from DNA origami rafts

    Science.gov (United States)

    He, Xiaojin; Sha, Ruojie; Zhuo, Rebecca; Mi, Yongli; Chaikin, Paul M.; Seeman, Nadrian C.

    2017-10-01

    Self-replication and evolution under selective pressure are inherent phenomena in life, and but few artificial systems exhibit these phenomena. We have designed a system of DNA origami rafts that exponentially replicates a seed pattern, doubling the copies in each diurnal-like cycle of temperature and ultraviolet illumination, producing more than 7 million copies in 24 cycles. We demonstrate environmental selection in growing populations by incorporating pH-sensitive binding in two subpopulations. In one species, pH-sensitive triplex DNA bonds enable parent-daughter templating, while in the second species, triplex binding inhibits the formation of duplex DNA templating. At pH 5.3, the replication rate of species I is ~1.3-1.4 times faster than that of species II. At pH 7.8, the replication rates are reversed. When mixed together in the same vial, the progeny of species I replicate preferentially at pH 7.8 similarly at pH 5.3, the progeny of species II take over the system. This addressable selectivity should be adaptable to the selection and evolution of multi-component self-replicating materials in the nanoscopic-to-microscopic size range.

  16. Gadolinium(III) ion selective sensor using a new synthesized Schiff's base as a sensing material

    International Nuclear Information System (INIS)

    Zamani, Hassan Ali; Mohammadhosseini, Majid; Haji-Mohammadrezazadeh, Saeed; Faridbod, Farnoush; Ganjali, Mohammad Reza; Meghdadi, Soraia; Davoodnia, Abolghasem

    2012-01-01

    According to a solution study which showed a selective complexation between N,N′-bis(methylsalicylidene)-2-aminobenzylamine (MSAB) and gadolinium ions, MSAB was used as a sensing element in construction of a gadolinium(III) ion selective electrode. Acetophenon (AP) was used as solvent mediator and sodium tetraphenyl borate (NaTPB) as an anion excluder. The electrode showed a good selectivity towards Gd(III) ions over a wide variety of cations tested. The constructed sensor displayed a Nernstian behavior (19.7 ± 0.3 mV/decade) in the concentration range of 1.0 × 10 −6 to 1.0 × 10 −2 mol L −1 with detection limit of 5.0 × 10 −7 mol L −1 and a short response time ( 3+ –PVC membrane sensor based on an ion carrier as sensing material is introduced. ► This technique is very simple and it's not necessary to use sophisticated equipment. ► This sensor shows good selectivity against other metal ions.

  17. Selective retention of oils in aqueous mixtures using palygorskite treated with waterproof materials

    International Nuclear Information System (INIS)

    Matesanz, J.M.; Aisa, C.; Aragues, J.L.; Ovelleiro, J.L.

    1994-01-01

    An oil-selective absorbent has been developed from clay materials that is easy to manufacture and use, and provides good results in different working conditions, compared to conventional water treatment methods. The absorbent can be used in fixed beds in a column or spread directly onto an oil spill. The absorbent is a palygorskite (attapulgite) coated with a silicone. The silicone coating reduces the water absorption capacity of the palygorskite to near zero, but affects oil absorption capacity very little. The Westinghouse method was used to evaluate the absorption capacity of the silicone-coated palygorskite. The results indicate that the material could be a good choice for reducing the organic matter content of drinking water. 4 refs., 2 figs., 2 tabs

  18. Mechanical characterization of selected adhesives and bulk materials at liquid nitrogen and room temperatures

    International Nuclear Information System (INIS)

    Fitzpatrick, C.M.; Stoddart, W.C.T.

    1977-01-01

    This paper presents the results of a series of mechanical tests on selected adhesives and bulk materials. The materials tested are of general interest to designers of magnets for cryogenic service and include several epoxies, a varnish, a B-stage glass cloth, insulation papers, and commercially available fiber-reinforced composites. These tests were performed at room temperature (293 K) and at liquid nitrogen temperature (77 K). The tests include both simple tension tests and lap shear tests with various adherends. The parameters critical to tensile or bond strength were varied as part of the test program. The procedures used to manufacture and test these specimens and the results of the tests are reported in this paper

  19. Mimicking heme enzymes in the solid state: metal-organic materials with selectively encapsulated heme.

    Science.gov (United States)

    Larsen, Randy W; Wojtas, Lukasz; Perman, Jason; Musselman, Ronald L; Zaworotko, Michael J; Vetromile, Carissa M

    2011-07-13

    To carry out essential life processes, nature has had to evolve heme enzymes capable of synthesizing and manipulating complex molecules. These proteins perform a plethora of chemical reactions utilizing a single iron porphyrin active site embedded within an evolutionarily designed protein pocket. We herein report the first class of metal-organic materials (MOMs) that mimic heme enzymes in terms of both structure and reactivity. The MOMzyme-1 class is based upon a prototypal MOM, HKUST-1, into which catalytically active metalloporphyrins are selectively encapsulated in a "ship-in-a-bottle" fashion within one of the three nanoscale cages that exist in HKUST-1. MOMs offer unparalleled levels of permanent porosity and their modular nature affords enormous diversity of structures and properties. The MOMzyme-1 class could therefore represent a new paradigm for heme biomimetic catalysis since it combines the activity of a homogeneous catalyst with the stability and recyclability of heterogeneous catalytic systems within a single material.

  20. Selecting the minimum risk route in the transportation of hazardous materials

    Directory of Open Access Journals (Sweden)

    Marijan Žura

    1992-12-01

    Full Text Available The transportation of hazardous materials is a broad and complex topic. Percent and iveight of accidents of vehicles carrying dangerous goods are growing fast. Modern computer based information system for dangerous materials management is becoming more and more important. In this paper I present an interactive software system for minimum risk route selection based on the PC ARC/INFO. The model computes optimal path based on accident probability is computed from traffic accident rates, highway operational speed, traffic volume and technical characteristic of the roadwidth, radius and slope. Dangerous goods are classified into nine classes according to their impact to different sensible environment elements. Those sensible elements are drinking water resourses, natural heritage, forestry, agricultural areas, cultural heritage, urban areas and tourist resorts. Some results of system implementation on Slovenia road network are be presented.

  1. Diffusion, Thermal Properties and Chemical Compatibilities of Select MAX Phases with Materials For Advanced Nuclear Systems

    Energy Technology Data Exchange (ETDEWEB)

    Barsoum, Michel [Drexel Univ., Philadelphia, PA (United States); Bentzel, Grady [Drexel Univ., Philadelphia, PA (United States); Tallman, Darin J. [Drexel Univ., Philadelphia, PA (United States); Sindelar, Robert [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Garcia-Diaz, Brenda [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hoffman, Elizabeth [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-04-04

    The demands of Gen IV nuclear power plants for long service life under neutron irradiation at high temperature are severe. Advanced materials that would withstand high temperatures (up to 1000+ ºC) to high doses in a neutron field would be ideal for reactor internal structures and would add to the long service life and reliability of the reactors. The objective of this work is to investigate the chemical compatibility of select MAX with potential materials that are important for nuclear energy, as well as to measure the thermal transport properties as a function of neutron irradiation. The chemical counterparts chosen for this work are: pyrolytic carbon, SiC, U, Pd, FLiBe, Pb-Bi and Na, the latter 3 in the molten state. The thermal conductivities and heat capacities of non-irradiated MAX phases will be measured.

  2. Highly selective and stable carbon dioxide uptake in polyindole-derived microporous carbon materials.

    Science.gov (United States)

    Saleh, Muhammad; Tiwari, Jitendra N; Kemp, K Christain; Yousuf, Muhammad; Kim, Kwang S

    2013-05-21

    Adsorption with solid sorbents is considered to be one of the most promising methods for the capture of carbon dioxide (CO₂) from power plant flue gases. In this study, microporous carbon materials used for CO₂ capture were synthesized by the chemical activation of polyindole nanofibers (PIF) at temperatures from 500 to 800 °C using KOH, which resulted in nitrogen (N)-doped carbon materials. The N-doped carbon materials were found to be microporous with an optimal adsorption pore size for CO₂ of 0.6 nm and a maximum (Brunauer-Emmett-Teller) BET surface area of 1185 m(2) g(-1). The PIF activated at 600 °C (PIF6) has a surface area of 527 m(2) g(-1) and a maximum CO₂ storage capacity of 3.2 mmol g(-1) at 25 °C and 1 bar. This high CO₂ uptake is attributed to its highly microporous character and optimum N content. Additionally, PIF6 material displays a high CO₂ uptake at low pressure (1.81 mmol g(-1) at 0.2 bar and 25 °C), which is the best low pressure CO₂ uptake reported for carbon-based materials. The adsorption capacity of this material remained remarkably stable even after 10 cycles. The isosteric heat of adsorption was calculated to be in the range of 42.7-24.1 kJ mol(-1). Besides the excellent CO₂ uptake and stability, PIF6 also exhibits high selectivity values for CO₂ over N₂, CH₄, and H₂ of 58.9, 12.3, and 101.1 at 25 °C, respectively, and these values are significantly higher than reported values.

  3. Biomimicry in Product Design through Materials Selection and Computer Aided Engineering

    Science.gov (United States)

    Alexandridis, G.; Tzetzis, D.; Kyratsis, P.

    2016-11-01

    The aim of this study is to demonstrate a 7-step methodology that describes the way nature can act as a source of inspiration for the design and the development of a product. Furthermore, it suggests special computerized tools and methods for the product optimization regarding its environmental impact i.e. material selection, production methods. For validation purposes, a garden chaise lounge that imitates the form of a scorpion was developed as a result for the case study and the presentation of the current methodology.

  4. Material Deprivation in Selected EU Countries According to EU-SILC Income Statistics

    Directory of Open Access Journals (Sweden)

    Stávková Jana

    2012-06-01

    Full Text Available The article deals with issues of households at risk of poverty in relative conception. Income poverty means a situation when the threshold of 0.6 of median income is not achieved. The analysis of a broader definition of poverty is based on identification and assessment of material deprivation factors, including: financial stress, housing conditions, availability of consumer durables and basic needs. Data sources are based EU-SILC dataset. Presented analysis is focused on selected EU countries, namely Czech Republic, Finland, France, Spain and United Kingdom. The result identifies the problem areas that cause deprivation symptoms.

  5. Mould Design and Material selection for Film Insert Moulding of Direct Methanol Fuel Cell Packaging

    DEFF Research Database (Denmark)

    Wöhner, Timo; Senkbeil, S.; Olesen, T. L.

    2015-01-01

    This paper presents the mould design for an injection moulding (IM) process for the production of a methanol container for the use in small, passive Direct Methanol Fuel Cell (DMFC) systems, which are intended to be used in behind-the-ear hearing aid systems. One of the crucial properties...... for the production of containers with different venting area and location of the venting holes and the use of different membrane thicknesses by using the same mould. Mould design and material selection are presented....

  6. Selection of flowing liquid lead target structural materials for accelerator driven transmutation applications

    International Nuclear Information System (INIS)

    Park, J.J.; Buksa, J.J.

    1994-01-01

    The beam entry window and container for a liquid lead spallation target will be exposed to high fluxes of protons and neutrons that are both higher in magnitude and energy than have been experienced in proton accelerators and fission reactors, as well as in a corrosive environment. The structural material of the target should have a good compatibility with liquid lead, a sufficient mechanical strength at elevated temperatures, a good performance under an intense irradiation environment, and a low neutron absorption cross section; these factors have been used to rank the applicability of a wide range of materials for structural containment Nb-1Zr has been selected for use as the structural container for the LANL ABC/ATW molten lead target. Corrosion and mass transfer behavior for various candidate structural materials in liquid lead are reviewed, together with the beneficial effects of inhibitors and various coatings to protect substrate against liquid lead corrosion. Mechanical properties of some candidate materials at elevated temperatures and the property changes resulting from 800 MeV proton irradiation are also reviewed

  7. Development of the Indigenous Child-Initiated Pretend Play Assessment: Selection of play materials and administration.

    Science.gov (United States)

    Dender, Alma; Stagnitti, Karen

    2011-02-01

    There is a need for culturally appropriate assessments for Australian Indigenous children. This article reports the selection of culturally appropriate and gender-neutral play materials, and changes in administration identified to develop further the Indigenous Child-Initiated Pretend Play Assessment (I-ChIPPA). Twenty-three typically developing children aged four to six years from the Pilbara region in Western Australia participated in the study. Children were presented with four sets of play materials and frequency counts were recorded for each time the child used one of the play materials in a pretend play action. Twelve of the 23 children came to play in pairs. Both boys and girls used the Pilbara toy set including the dark coloured dolls and Pilbara region animals, more frequently than the standardised play materials from the Child-Initiated Pretend Play Assessment (ChIPPA). This study reports the first steps in the development of the I-ChIPPA. Future development will include the refinement of the administration and scoring with pairs of children, and then validity testing the assessment. © 2010 The Authors. Australian Occupational Therapy Journal © 2010 Australian Association of Occupational Therapists.

  8. The diffusion properties of ion implanted species in selected target materials

    International Nuclear Information System (INIS)

    Alton, G.D.; Dellwo, J.; Carter, H.K.; Kormicki, J.; Bartolo, G. di; Batchelder, J.C.; Breitenbach, J.; Chediak, J.A.; Jentoff-Nilsen, K.; Ichikawa, S.

    1995-01-01

    Experiments important to the future success of the Holifield Radioactive Ion Beam Facility (HRIBF) are in progress at the Oak Ridge National Laboratory which are designed to select the most appropriate target material for generating a particular radioactive ion beam (RIB). The 25-MV HHIRF tandem accelerator is used to implant stable complements of interesting radioactive elements into refractory targets mounted in a high-temperature FEBIAD ion source which is open-quotes on-lineclose quotes at the UNISOR facility. The intensity versus time of implanted species, which diffuse from the high-temperature target material (∼1700 degrees C) and are ionized in the FEBIAD ion source, is used to determine release times for a particular projectile/target material combination. From such release data, diffusion coefficients can be derived by fitting the theoretical results obtained by computational solution of Fick's second equation to experimental data. The diffusion coefficient can be used subsequently to predict the release properties of the particular element from the same material in other target geometries and at other temperatures, provided that the activation energy is also known. Diffusion coefficients for Cl implanted into and diffused from CeS and Zr 5 Si 3 and As, Br, and Se implanted into and diffused from Zr 5 Ge 3 have been derived from the resulting intensity versus time profiles. Brief descriptions of the experimental apparatus and procedures utilized in the present experiments and plans for future related experiments are presented

  9. PeptideManager: A Peptide Selection Tool for Targeted Proteomic Studies Involving Mixed Samples from Different Species

    Directory of Open Access Journals (Sweden)

    Kevin eDemeure

    2014-09-01

    Full Text Available The search for clinically useful protein biomarkers using advanced mass spectrometry approaches represents a major focus in cancer research. However, the direct analysis of human samples may be challenging due to limited availability, the absence of appropriate control samples, or the large background variability observed in patient material. As an alternative approach, human tumors orthotopically implanted into a different species (xenografts are clinically relevant models that have proven their utility in pre-clinical research. Patient derived xenografts for glioblastoma have been extensively characterized in our laboratory and have been shown to retain the characteristics of the parental tumor at the phenotypic and genetic level. Such models were also found to adequately mimic the behavior and treatment response of human tumors. The reproducibility of such xenograft models, the possibility to identify their host background and perform tumor-host interaction studies, are major advantages over the direct analysis of human samples.At the proteome level, the analysis of xenograft samples is challenged by the presence of proteins from two different species which, depending on tumor size, type or location, often appear at variable ratios. Any proteomics approach aimed at quantifying proteins within such samples must consider the identification of species specific peptides in order to avoid biases introduced by the host proteome. Here, we present an in-house methodology and tool developed to select peptides used as surrogates for protein candidates from a defined proteome (e.g., human in a host proteome background (e.g., mouse, rat suited for a mass spectrometry analysis. The tools presented here are applicable to any species specific proteome, provided a protein database is available. By linking the information from both proteomes, PeptideManager significantly facilitates and expedites the selection of peptides used as surrogates to analyze

  10. Thermodynamic consistency of viscoplastic material models involving external variable rates in the evolution equations for the internal variables

    International Nuclear Information System (INIS)

    Malmberg, T.

    1993-09-01

    The objective of this study is to derive and investigate thermodynamic restrictions for a particular class of internal variable models. Their evolution equations consist of two contributions: the usual irreversible part, depending only on the present state, and a reversible but path dependent part, linear in the rates of the external variables (evolution equations of ''mixed type''). In the first instance the thermodynamic analysis is based on the classical Clausius-Duhem entropy inequality and the Coleman-Noll argument. The analysis is restricted to infinitesimal strains and rotations. The results are specialized and transferred to a general class of elastic-viscoplastic material models. Subsequently, they are applied to several viscoplastic models of ''mixed type'', proposed or discussed in the literature (Robinson et al., Krempl et al., Freed et al.), and it is shown that some of these models are thermodynamically inconsistent. The study is closed with the evaluation of the extended Clausius-Duhem entropy inequality (concept of Mueller) where the entropy flux is governed by an assumed constitutive equation in its own right; also the constraining balance equations are explicitly accounted for by the method of Lagrange multipliers (Liu's approach). This analysis is done for a viscoplastic material model with evolution equations of the ''mixed type''. It is shown that this approach is much more involved than the evaluation of the classical Clausius-Duhem entropy inequality with the Coleman-Noll argument. (orig.) [de

  11. Nuclear substructure reorganization during late stageerythropoiesis is selective and does not involve caspase cleavage ofmajor nuclear substructural proteins

    Energy Technology Data Exchange (ETDEWEB)

    Krauss, Sharon Wald; Lo, Annie J.; Short, Sarah A.; Koury, MarkJ.; Mohandas, Narla; Chasis, Joel Anne

    2005-04-06

    Enucleation, a rare feature of mammalian differentiation, occurs in three cell types: erythroblasts, lens epithelium and keratinocytes. Previous investigations suggest that caspase activation functions in lens epithelial and keratinocyte enucleation, as well as in early erythropoiesis encompassing BFU-E differentiation to proerythroblast. To determine whether caspase activation contributes to later erythropoiesis and whether nuclear substructures other than chromatin reorganize, we analyzed distributions of nuclear subcompartment proteins and assayed for caspase-induced cleavage of subcompartmental target proteins in mouse erythroblasts. We found that patterns of lamin B in the filamentous network interacting with both the nuclear envelope and DNA, nuclear matrix protein NuMA, and splicing factors Sm and SC35 persisted during nuclear condensation, consistent with effective transcription of genes expressed late in differentiation. Thus nuclear reorganization prior to enucleation is selective, allowing maintenance of critical transcriptional processes independent of extensive chromosomal reorganization. Consistent with these data, we found no evidence for caspase-induced cleavage of major nuclear subcompartment proteins during late erythropoiesis, in contrast to what has been observed in early erythropoiesis and in lens epithelial and keratinocyte differentiation. These findings imply that nuclear condensation and extrusion during terminal erythroid differentiation involve novel mechanisms that do not entail major activation of apoptotic machinery.

  12. Selection during crop diversification involves correlated evolution of the circadian clock and ecophysiological traits in Brassica rapa.

    Science.gov (United States)

    Yarkhunova, Yulia; Edwards, Christine E; Ewers, Brent E; Baker, Robert L; Aston, Timothy Llewellyn; McClung, C Robertson; Lou, Ping; Weinig, Cynthia

    2016-04-01

    Crop selection often leads to dramatic morphological diversification, in which allocation to the harvestable component increases. Shifts in allocation are predicted to impact (as well as rely on) physiological traits; yet, little is known about the evolution of gas exchange and related anatomical features during crop diversification. In Brassica rapa, we tested for physiological differentiation among three crop morphotypes (leaf, turnip, and oilseed) and for correlated evolution of circadian, gas exchange, and phenological traits. We also examined internal and surficial leaf anatomical features and biochemical limits to photosynthesis. Crop types differed in gas exchange; oilseed varieties had higher net carbon assimilation and stomatal conductance relative to vegetable types. Phylogenetically independent contrasts indicated correlated evolution between circadian traits and both gas exchange and biomass accumulation; shifts to shorter circadian period (closer to 24 h) between phylogenetic nodes are associated with higher stomatal conductance, lower photosynthetic rate (when CO2 supply is factored out), and lower biomass accumulation. Crop type differences in gas exchange are also associated with stomatal density, epidermal thickness, numbers of palisade layers, and biochemical limits to photosynthesis. Brassica crop diversification involves correlated evolution of circadian and physiological traits, which is potentially relevant to understanding mechanistic targets for crop improvement. © 2015 The Authors. New Phytologist © 2015 New Phytologist Trust.

  13. Initiator of carcinogenesis selectively and stably inhibits stem cell differentiation: a concept that initiation of carcinogenesis involves multiple phases

    International Nuclear Information System (INIS)

    Scott, R.E.; Maercklein, P.B.

    1985-01-01

    A concept of carcinogenesis was recently devised in our laboratory that suggests the development of defects in the control of cell differentiation is associated with an early phase of carcinogenesis. To test this proposal directly, the effects of an initiator of carcinogenesis (i.e., UV irradiation) on proadipocyte stem cell differentiation and proliferation was assayed. In this regard, 3T3 T proadipocytes represent a nontransformed mesenchymal stem cell line that possesses the ability to regulate its differentiation at a distinct state in the G 1 phase of the cell cycle as well as the ability to regulate its proliferation at two additional G 1 states. The results establish that a slow dosage of 254 nm UV irradiation selectivity and stably inhibits the differentiation of a high percentage of proadipocyte stem cells without significantly altering their ability to regulate cellular proliferation in growth factor-deficient or nutrient-deficient culture conditions. Differentiation-defect proadipocyte stem cells are demonstrated not to be completely transformed but to show an increased spontaneous transformation rate, as evidenced by the formation of type III foci in high density cell cultures. These data support the role of defects in the control of differentiation in the inhibition of carcinogenesis. These observations support a concept that the initiation of carcinogenesis involves multiple phases

  14. Selective chelation-supercritical fluid extraction of metal ions from waste materials

    International Nuclear Information System (INIS)

    Wai, C.N.; Laintz, K.E.; Yonker, C.R.

    1993-01-01

    The removal of toxic organics, metals, and radioisotopes from solids or liquids is a major concern in the treatment of industrial and nuclear wastes. For this reason, developing methods for selective separation of toxic metals and radioactive materials from solutions of complex matrix is an important problem in environmental research. Recent developments indicate supercritical fluids are good solvents for organic compounds. Many gases become supercritical fluids under moderate temperatures and pressures. For example, the critical temperature and pressure of carbon dioxide are 31 degrees C and 73 atm, respectively. The high diffusivity, low viscosity, and T-P dependence of solvent strength are some attractive properties of supercritical fluid extraction (SFE). Since CO 2 offers the additional benefits of stability and non-toxicity, the SFE technique avoids generation of organic liquid waste and exposure of personnel to toxic solvents. While direct extraction of metal ions by supercritical fluids is highly inefficient, these ions when complexed with organic ligands become quite soluble in supercritical fluids. Specific ligands can be used to achieve selective extraction of metal ions in this process. After SFE, the fluid phase can be depressurized for precipitation of the metal chelates and recycled. The ligand can also be regenerated for repeated use. The success of this selective chelation-supercritical fluid extraction (SC-SFE) process depends on a number of factors including the efficiencies of the selective chelating agents, solubilities of metal chelates in supercritical fluids, rate of extraction, ease of regeneration of the ligands, etc. In this report, the authors present recent results on the studies of the solubilities of metal chelates in supercritical CO 2 , experimental ions from aqueous solution, and the development of selective chelating agents (ionizable crown ethers) for the extraction of lanthanides and actinides

  15. Evolutionary selection growth of two-dimensional materials on polycrystalline substrates

    Science.gov (United States)

    Vlassiouk, Ivan V.; Stehle, Yijing; Pudasaini, Pushpa Raj; Unocic, Raymond R.; Rack, Philip D.; Baddorf, Arthur P.; Ivanov, Ilia N.; Lavrik, Nickolay V.; List, Frederick; Gupta, Nitant; Bets, Ksenia V.; Yakobson, Boris I.; Smirnov, Sergei N.

    2018-03-01

    There is a demand for the manufacture of two-dimensional (2D) materials with high-quality single crystals of large size. Usually, epitaxial growth is considered the method of choice1 in preparing single-crystalline thin films, but it requires single-crystal substrates for deposition. Here we present a different approach and report the synthesis of single-crystal-like monolayer graphene films on polycrystalline substrates. The technological realization of the proposed method resembles the Czochralski process and is based on the evolutionary selection2 approach, which is now realized in 2D geometry. The method relies on `self-selection' of the fastest-growing domain orientation, which eventually overwhelms the slower-growing domains and yields a single-crystal continuous 2D film. Here we have used it to synthesize foot-long graphene films at rates up to 2.5 cm h-1 that possess the quality of a single crystal. We anticipate that the proposed approach could be readily adopted for the synthesis of other 2D materials and heterostructures.

  16. Selected mechanical properties of aluminum composite materials reinforced with SiC particles

    Directory of Open Access Journals (Sweden)

    A. Kurzawa

    2008-07-01

    Full Text Available This work presents the results of research concerning influence of ceramic particles’ content of silicon carbide on selected mechanical properties of type AW-AlCu4Mg2Mn - SiC composite materials. Composites produced of SiC particles with pressure infiltration method of porous preform and subject to hot plastic forming in the form of open die forging were investigated. The experimental samples contained from 5% up to 45% of reinforcing SiC particles of 8÷10μm diameter. Studies of strength properties demonstrated that the best results, in case of tensile strength as well as offset yield strength, might be obtained while applying reinforcement in the amount of 20-25% vol. of SiC. Application of higher than 25% vol. contents of reinforcing particles leads to gradual strength loss. The investigated composites were characterized by very high functional properties, such as hardness and abrasive wear resistance, whose values increase strongly with the increase of reinforcement amount. The presented results of the experiments shall allow for a more precise component selection of composite materials at the stage of planning and design of their properties.

  17. Ethnography of Cool Roof Retrofits: The Role of Rebates in the Materials Selection Process

    Energy Technology Data Exchange (ETDEWEB)

    Mazur-Stommen, Susan [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2011-02-01

    In the summer of 2010, ethnographic research was conducted with nine households in the Bay Area and Sacramento region. The purpose of this task was to collect methodologically grounded insights into how and why consumers chose the cool roofing material they selected. These nine households comprised fifteen respondents, and their dependents. They were selected from among a pool of respondents to a mail solicitation of all Sacramento Municipal Utility District and Pacific Gas and Electric customers who had received a rebate for their cool roof retrofit. Consumers are uniformly happy with their cool roof retrofits. Consumers typically stayed very close to the aesthetic of the original roof style. Price was not a primary concern, while longevity was paramount. Consumers did not use roofing price, nor energy savings (with one exception), in tracking return on investment through energy savings. The utility rebate had little role to play in terms of incentivizing customers to choose cool materials. Contractors were critical partners in the decision-­making process.

  18. Influence of material selection on the structural behavior of a wave energy converter

    Directory of Open Access Journals (Sweden)

    Cândida M. S. P. Malça

    2014-09-01

    Full Text Available In the last decades, the world energy demand has raised significantly. Concerning this fact, wave energy should be considered as a valid alternative for electricity production. Devices suitable to harness this kind of renewable energy source and convert it into electricity are not yet commercially competitive. This paper is focused on the selection and analysis of different types of elastic materials and their influence on the structural behavior of a wave energy converter (WEC. After a brief characterization of the device, a tridimensional computer aided design (3D CAD numerical model was built and several finite element analyses (FEA were performed through a commercial finite element code. The main components of the WEC, namely the buoy, supporting cables and hydraulic cylinder were simulated assuming different materials. The software used needs, among other parameters, the magnitude of the resultant hydrodynamic forces acting upon the floating buoy obtained from a WEC time domain simulator (TDS which was built based on the WEC dynamic model previously developed. The Von Mises stress gradients and displacement fields determined by the FEA demonstrated that, regardless of the WEC component, the materials with low Young's modulus seems to be unsuitable for this kind of application. The same is valid for the material yield strength since materials with a higher yield strength lead to a better structural behavior of WEC components because lower stress and displacement values were obtained. The developed 3D CAD numerical model showed to be suitable to analyze different combinations of structural conditions. They could depend of different combinations of buoy position and resultant hydrodynamic forces acting upon the buoy, function of the specific sea wave parameters found on the deployment site.

  19. Microstructure and Magnetic Properties of Magnetic Material Fabricated by Selective Laser Melting

    Science.gov (United States)

    Jhong, Kai Jyun; Huang, Wei-Chin; Lee, Wen Hsi

    Selective Laser Melting (SLM) is a powder-based additive manufacturing which is capable of producing parts layer-by-layer from a 3D CAD model. The aim of this study is to adopt the selective laser melting technique to magnetic material fabrication. [1]For the SLM process to be practical in industrial use, highly specific mechanical properties of the final product must be achieved. The integrity of the manufactured components depend strongly on each single laser-melted track and every single layer, as well as the strength of the connections between them. In this study, effects of the processing parameters, such as the space distance of surface morphology is analyzed. Our hypothesis is that when a magnetic product is made by the selective laser melting techniques instead of traditional techniques, the finished component will have more precise and effective properties. This study analyzed the magnitudes of magnetic properties in comparison with different parameters in the SLM process and compiled a completed product to investigate the efficiency in contrast with products made with existing manufacturing processes.

  20. Selectively Modulating Triplet Exciton Formation in Host Materials for Highly Efficient Blue Electrophosphorescence.

    Science.gov (United States)

    Li, Huanhuan; Bi, Ran; Chen, Ting; Yuan, Kai; Chen, Runfeng; Tao, Ye; Zhang, Hongmei; Zheng, Chao; Huang, Wei

    2016-03-23

    The concept of limiting the triplet exciton formation to fundamentally alleviate triplet-involved quenching effects is introduced to construct host materials for highly efficient and stable blue phosphorescent organic light-emitting diodes (PhOLEDs). The low triplet exciton formation is realized by small triplet exciton formation fraction and rate with high binding energy and high reorganization energy of triplet exciton. Demonstrated in two analogue molecules in conventional donor-acceptor molecule structure for bipolar charge injection and transport with nearly the same frontier orbital energy levels and triplet excited energies, the new concept host material shows significantly suppressed triplet exciton formation in the host to avoid quenching effects, leading to much improved device efficiencies and stabilities. The low-voltage-driving blue PhOLED devices exhibit maximum efficiencies of 43.7 cd A(-1) for current efficiency, 32.7 lm W(-1) for power efficiency, and 20.7% for external quantum efficiency with low roll-off and remarkable relative quenching effect reduction ratio up to 41%. Our fundamental solution for preventing quenching effects of long-lived triplet excitons provides exciting opportunities for fabricating high-performance devices using the advanced host materials with intrinsically small triplet exciton formation cross section.

  1. Deuterium pumping and erosion behavior of selected graphite materials under high flux plasma bombardment in PISCES

    International Nuclear Information System (INIS)

    Hirooka, Y.; Conn, R.W.; Goebel, D.M.; LaBombard, B.; Lehmer, R.; Leung, W.K.; Nygren, R.E.; Ra, Y.

    1988-06-01

    Deuterium plasma recycling and chemical erosion behavior of selected graphite materials have been investigated using the PISCES-A facility. These materials include: Pyro-graphite; 2D-graphite weave; 4D-graphite weave; and POCO-graphite. Deuterium plasma bombardment conditions are: fluxes around 7 /times/ 10 17 ions s/sup /minus/1/cm/sup /minus/2/; exposure time in the range from 10 to 100 s; bombarding energy of 300 eV; and graphite temperatures between 20 and 120/degree/C. To reduce deuterium plasma recycling, several approaches have been investigated. Erosion due to high-fluence helium plasma conditioning significantly increases the surface porosity of POCO-graphite and 4D-graphite weave whereas little change for 2D-graphite weave and Pyro-graphite. The increased pore openings and refreshed in-pore surface sites are found to reduce the deuterium plasma recycling and chemical erosion rates at transient stages. The steady state recycling rates for these graphite materials can be also correlated to the surface porosity. Surface topographical modification by machined-grooves noticeably reduces the steady state deuterium recycling rate and the impurity emission from the surface. These surface topography effects are attributed to co-deposition of remitted deuterium, chemically sputtered hydrocarbon and physically sputtered carbon under deuterium plasma bombardment. The co-deposited film is found to have a characteristic surface morphology with dendritic microstructures. 18 ref., 4 figs., 1 tab

  2. Material selection and assembly method of battery pack for compact electric vehicle

    Science.gov (United States)

    Lewchalermwong, N.; Masomtob, M.; Lailuck, V.; Charoenphonphanich, C.

    2018-01-01

    Battery packs become the key component in electric vehicles (EVs). The main costs of which are battery cells and assembling processes. The battery cell is indeed priced from battery manufacturers while the assembling cost is dependent on battery pack designs. Battery pack designers need overall cost as cheap as possible, but it still requires high performance and more safety. Material selection and assembly method as well as component design are very important to determine the cost-effectiveness of battery modules and battery packs. Therefore, this work presents Decision Matrix, which can aid in the decision-making process of component materials and assembly methods for a battery module design and a battery pack design. The aim of this study is to take the advantage of incorporating Architecture Analysis method into decision matrix methods by capturing best practices for conducting design architecture analysis in full account of key design components critical to ensure efficient and effective development of the designs. The methodology also considers the impacts of choice-alternatives along multiple dimensions. Various alternatives for materials and assembly techniques of battery pack are evaluated, and some sample costs are presented. Due to many components in the battery pack, only seven components which are positive busbar and Z busbar are represented in this paper for using decision matrix methods.

  3. Materials selection, qualification and manufacturing of the in-vessel divertor cryopump for JET

    International Nuclear Information System (INIS)

    Papastergiou, S.; Obert, W.; Thompson, E.

    1994-01-01

    The introduction of a cryopump into the interior of a large tokamak raises several technical problems related to the thermal stresses, eddy current forces and choice of materials. The JET divertor cryopump has been optimized in terms of stresses, flow stability and operation - the liquid nitrogen cooled chevron structure in particular having to fulfill conflicting requirements at cryogenic temperatures. These requirements include good thermal conductivity in order to minimize thermal gradients (to reduce the radiative heat load onto the liquid helium circuit), high electrical resistivity (to minimize eddy current stresses), high mechanical strength and good mechanical formability. This paper reports on the materials selection based on measurements of properties at cryogenic and elevated temperatures and the development of an optimized thermal treatment combining solution heat treatment, brazing and precipitation hardening. It also reports on the successful development of various manufacturing technologies which have been employed including (a) techniques for brazing of the chosen copper alloy onto inconel and stainless steel, (b) surface blackening of the copper alloy with plasma sprayed ceramic coatings that are vacuum compatible and able to withstand temperatures between 70 K and 1135 K and (c) plasma spray deposition of copper onto stainless steel in order to produce an anisotropic composite material with improved thermal conductivity, high strength and high electrical resistivity for use at temperatures between 70 K and 650 K

  4. Tritium Suicide Selection Identifies Proteins Involved in the Uptake and Intracellular Transport of Sterols in Saccharomyces cerevisiae▿

    Science.gov (United States)

    Sullivan, David P.; Georgiev, Alexander; Menon, Anant K.

    2009-01-01

    Sterol transport between the plasma membrane (PM) and the endoplasmic reticulum (ER) occurs by a nonvesicular mechanism that is poorly understood. To identify proteins required for this process, we isolated Saccharomyces cerevisiae mutants with defects in sterol transport. We used Upc2-1 cells that have the ability to take up sterols under aerobic conditions and exploited the observation that intracellular accumulation of exogenously supplied [3H]cholesterol in the form of [3H]cholesteryl ester requires an intact PM-ER sterol transport pathway. Upc2-1 cells were mutagenized using a transposon library, incubated with [3H]cholesterol, and subjected to tritium suicide selection to isolate mutants with a decreased ability to accumulate [3H]cholesterol. Many of the mutants had defects in the expression and trafficking of Aus1 and Pdr11, PM-localized ABC transporters that are required for sterol uptake. Through characterization of one of the mutants, a new role was uncovered for the transcription factor Mot3 in controlling expression of Aus1 and Pdr11. A number of mutants had transposon insertions in the uncharacterized Ydr051c gene, which we now refer to as DET1 (decreased ergosterol transport). These mutants expressed Aus1 and Pdr11 normally but were severely defective in the ability to accumulate exogenously supplied cholesterol. The transport of newly synthesized sterols from the ER to the PM was also defective in det1Δ cells. These data indicate that the cytoplasmic protein encoded by DET1 is involved in intracellular sterol transport. PMID:19060182

  5. Preliminary materials selection issues for the next generation nuclear plant reactor pressure vessel.

    Energy Technology Data Exchange (ETDEWEB)

    Natesan, K.; Majumdar, S.; Shankar, P. S.; Shah, V. N.; Nuclear Engineering Division

    2007-03-21

    In the coming decades, the United States and the entire world will need energy supplies to meet the growing demands due to population increase and increase in consumption due to global industrialization. One of the reactor system concepts, the Very High Temperature Reactor (VHTR), with helium as the coolant, has been identified as uniquely suited for producing hydrogen without consumption of fossil fuels or the emission of greenhouse gases [Generation IV 2002]. The U.S. Department of Energy (DOE) has selected this system for the Next Generation Nuclear Plant (NGNP) Project, to demonstrate emissions-free nuclear-assisted electricity and hydrogen production within the next 15 years. The NGNP reference concepts are helium-cooled, graphite-moderated, thermal neutron spectrum reactors with a design goal outlet helium temperature of {approx}1000 C [MacDonald et al. 2004]. The reactor core could be either a prismatic graphite block type core or a pebble bed core. The use of molten salt coolant, especially for the transfer of heat to hydrogen production, is also being considered. The NGNP is expected to produce both electricity and hydrogen. The process heat for hydrogen production will be transferred to the hydrogen plant through an intermediate heat exchanger (IHX). The basic technology for the NGNP has been established in the former high temperature gas reactor (HTGR) and demonstration plants (DRAGON, Peach Bottom, AVR, Fort St. Vrain, and THTR). In addition, the technologies for the NGNP are being advanced in the Gas Turbine-Modular Helium Reactor (GT-MHR) project, and the South African state utility ESKOM-sponsored project to develop the Pebble Bed Modular Reactor (PBMR). Furthermore, the Japanese HTTR and Chinese HTR-10 test reactors are demonstrating the feasibility of some of the planned components and materials. The proposed high operating temperatures in the VHTR place significant constraints on the choice of material selected for the reactor pressure vessel for

  6. Study of Material Consolidation at Higher Throughput Parameters in Selective Laser Melting of Inconel 718

    Science.gov (United States)

    Prater, Tracie

    2016-01-01

    Selective Laser Melting (SLM) is a powder bed fusion additive manufacturing process used increasingly in the aerospace industry to reduce the cost, weight, and fabrication time for complex propulsion components. SLM stands poised to revolutionize propulsion manufacturing, but there are a number of technical questions that must be addressed in order to achieve rapid, efficient fabrication and ensure adequate performance of parts manufactured using this process in safety-critical flight applications. Previous optimization studies for SLM using the Concept Laser M1 and M2 machines at NASA Marshall Space Flight Center have centered on machine default parameters. The objective of this work is to characterize the impact of higher throughput parameters (a previously unexplored region of the manufacturing operating envelope for this application) on material consolidation. In phase I of this work, density blocks were analyzed to explore the relationship between build parameters (laser power, scan speed, hatch spacing, and layer thickness) and material consolidation (assessed in terms of as-built density and porosity). Phase II additionally considers the impact of post-processing, specifically hot isostatic pressing and heat treatment, as well as deposition pattern on material consolidation in the same higher energy parameter regime considered in the phase I work. Density and microstructure represent the "first-gate" metrics for determining the adequacy of the SLM process in this parameter range and, as a critical initial indicator of material quality, will factor into a follow-on DOE that assesses the impact of these parameters on mechanical properties. This work will contribute to creating a knowledge base (understanding material behavior in all ranges of the AM equipment operating envelope) that is critical to transitioning AM from the custom low rate production sphere it currently occupies to the world of mass high rate production, where parts are fabricated at a rapid

  7. Public Involvement in Repository Site Selection for Nuclear Waste: Towards a more Dynamic View in Decision-Making Processes

    Energy Technology Data Exchange (ETDEWEB)

    Kruetli, Pius; Stauffacher, Michael; Flueeler, Thomas; Scholz, Roland W. [ETH Zuerich (Switzerland). lnst. for Human-Environment Systems (HES)

    2006-09-15

    This paper discusses possibilities of public involvement in radioactive waste management. A general overview of the radioactive waste issue is presented referring to a proposed model of the respective decision-making process. Based on the well known participation ladder by Arnstein, we differentiate various intensities of public involvement. A matrix with public involvement and the decision-making process is introduced and three prototypical patterns are discussed. We conclude that time frame, the level of public involvement and the mission have to be considered as well as techniques and the overarching context - all in all, a systematic and dynamic approach for public involvement is needed.

  8. Public Involvement in Repository Site Selection for Nuclear Waste: Towards a more Dynamic View in Decision-Making Processes

    International Nuclear Information System (INIS)

    Kruetli, Pius; Stauffacher, Michael; Flueeler, Thomas; Scholz, Roland W.

    2006-01-01

    This paper discusses possibilities of public involvement in radioactive waste management. A general overview of the radioactive waste issue is presented referring to a proposed model of the respective decision-making process. Based on the well known participation ladder by Arnstein, we differentiate various intensities of public involvement. A matrix with public involvement and the decision-making process is introduced and three prototypical patterns are discussed. We conclude that time frame, the level of public involvement and the mission have to be considered as well as techniques and the overarching context - all in all, a systematic and dynamic approach for public involvement is needed

  9. 33 CFR 338.2 - Activities involving the discharge of dredged or fill material into waters of the U.S.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Activities involving the discharge of dredged or fill material into waters of the U.S. 338.2 Section 338.2 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE OTHER CORPS ACTIVITIES INVOLVING...

  10. Guidance for consignors, rail operators and others involved in the packaging, labelling and carriage of radioactive material by rail. Pt. 5

    International Nuclear Information System (INIS)

    1996-01-01

    This document, part of a series of guides for those concerned with the road or rail transportation of dangerous goods, provides detailed recommendations for consignors, rail operators and others involved in the packaging, labelling and carriage of radioactive materials by rail. It covers the relevant legislation and regulations on the carriage of such dangerous goods to assist those involved with compliance. (UK)

  11. A prototype knowledge-based system for material selection of ceramic matrix composites of automotive engine components

    Energy Technology Data Exchange (ETDEWEB)

    Sapuan, S.M.; Jacob, M.S.D.; Mustapha, F.; Ismail, N

    2002-12-15

    A prototype knowledge based system (KBS) for material selection of ceramic matrix composites (CMC) for engine components such as piston, connecting rod and piston ring is proposed in this paper. The main aim of this research work is to select the most suitable material for the automotive engine components. The selection criteria are based upon the pre-defined constraint value. The constraint values are mechanical, physical properties and manufacturing techniques. The constraint values are the safety values for the product design. The constraint values are selected from the product design specification. The product design specification values are selected from the past design calculation and some values are calculated by the help of past design data. The knowledge-based system consists of several modules such as knowledge acquisition module, inference module and user interface module. The domains of the knowledge-based system are defined as objects and linked together by hierarchical graph. The system is capable of selecting the most suitable materials and ranks the materials with respect to their properties. The design engineers can choose the required materials related to the materials property.

  12. Selective Preparation of Furfural from Xylose over Sulfonic Acid Functionalized Mesoporous Sba-15 Materials

    Directory of Open Access Journals (Sweden)

    Panpan Li

    2011-04-01

    Full Text Available Sulfonic acid functionalized mesoporous SBA-15 materials were prepared using the co-condensation and grafting methods, respectively, and their catalytic performance in the dehydration of xylose to furfural was examined. SBA-15-SO3H(C prepared by the co-condensation method showed 92–95% xylose conversion and 74% furfural selectivity, and 68–70% furfural yield under the given reaction conditions. The deactivation and regeneration of the SBA-15-SO3H(C catalyst for the dehydration of xylose was also investigated. The results indicate that the used and regeneration catalysts retained the SBA-15 mesoporous structure, and the S content of SBA-15-SO3H(C almost did not change. The deactivation of the catalysts is proposed to be associated with the accumulation of byproducts, which is caused by the loss reaction of furfural. After regeneration by H2O2, the catalytic activity of the catalyst almost recovered.

  13. Selection of refractory materials for acid tanks at the CSN continuous pickling line

    International Nuclear Information System (INIS)

    Silva, Sidiney Nascimento; Marques, Oscar Rosa; Bueno, Mauricio Chaves; Longo, Elson; Silva Pinheiro, Adriano da

    1997-01-01

    Aiming at the revamping of the CSN continuous pickling line 4 acid tanks, a Post Mortem study of the refractory lining was carried out. The collected samples were characterized through techniques such as chemical analysis, mercury porosimetry, X-ray diffraction and scanning electronic microscopy. Trying to reproduce the operational conditions closely, laboratorial simulations were carried out. Such simulations lead to the addition of some alterations on the test method proposed by ABNT. Primarily, the sulfuric acid was substituted by hydrochloric acid (30%), containing iron in solution (130g/l). As result, it was concluded that acid resistant refractories containing a smaller alumina and /or corundum and mullite concentrations, presenting a smaller open porosity and average pore diameter, have a better performance face to corrosion due to hydrochloric acid solution. In addition, abrasion wear resistance tests, according to the ASTM-G65-85 standard were carried out in order to select different materials to the acid tanks cells. (author)

  14. Selective Laser Melting of Hot Gas Turbine Components: Materials, Design and Manufacturing Aspects

    DEFF Research Database (Denmark)

    Goutianos, Stergios

    2017-01-01

    are built additively to nearly net shape. This allows the fabrication of arbitrary complex geometries that cannot be made by conventional manufacturing techniques. However, despite the powerful capabilities of SLM, a number of issues (e.g. part orientation, support structures, internal stresses), have......Selective Laser Melting (SLM) allows the design and manufacturing of novel parts and structures with improved performance e.g. by incorporating complex and more efficient cooling schemes in hot gas turbine parts. In contrast to conventional manufacturing of removing material, with SLM parts...... to be considered in order to manufacture cost-effective and high quality parts at an industrial scale. These issues are discussed in the present work from an engineering point of view with the aim to provide simple quidelines to produce high quality SLM parts....

  15. Selection of Liner Materials and Design of Hazardous Water Facilities in Saudi Arabia

    Directory of Open Access Journals (Sweden)

    Sahel N. Abduljauwad

    2001-12-01

    Full Text Available Rapid development in Saudi Arabia has produced a broad spectrum of wastes.  In the last two decades, several refineries and petrochemical industries have been established. These industries have produced sludges and other toxic wastes which need proper planning for their handling and disposal. This paper covers design and selection of liner materials for two hazardous waste disposal sites. One of them is located in the Eastern Province of Saudi Arabia, while the second one is located in the Western part. The paper will present complete design details of the natural compacted and geosynthetic soil liners and the leachate collection and removal system for primary liners and leak detection/leachate collection and removal system for secondary liners.

  16. Materials selection of surface coatings in an advanced size reduction facility

    International Nuclear Information System (INIS)

    Briggs, J.L.; Younger, A.F.

    1980-01-01

    A materials selection test program was conducted to characterize optimum interior surface coatings for an advanced size reduction facility. The equipment to be processed by this facility consists of stainless steel apparatus (e.g., glove boxes, piping, and tanks) used for the chemical recovery of plutonium. Test results showed that a primary requirement for a satisfactory coating is ease of decontamination. A closely related concern is the resistance of paint films to nitric acid - plutonium environments. A vinyl copolymer base paint was the only coating, of eight paints tested, with properties that permitted satisfactory decontamination of plutonium and also performed equal to or better than the other paints in the chemical resistance, radiation stability, and impact tests

  17. Core–shell-typed Ag-SiO2 nanoparticles as solar selective coating materials

    International Nuclear Information System (INIS)

    Gao, Tao; Jelle, Bjørn Petter; Gustavsen, Arild

    2013-01-01

    Silver (Ag) nanoparticles with typical diameter of about 50 nm have been prepared via a polyol process. The as-prepared Ag nanoparticles are well crystallized and exhibit a characteristic surface plasmon resonance (SPR) band centered at ∼423 nm. The SPR band shows a strong dependence on the sizes of Ag nanoparticles and the types of the dielectric medium. Core–shell-typed Ag-SiO 2 nanoparticles have also been prepared by depositing a thin layer (∼25 nm) of silica on Ag nanoparticles. The core–shell-typed Ag-SiO 2 nanoparticles show similar optical behaviors (absorption, transmission, and reflection) but enhanced stability compared to those of the Ag nanoparticles, indicating that the core–shell-typed Ag-SiO 2 nanoparticles may be used as solar selective coating materials for architectural window applications.

  18. Gender involvement in manual material handling (mmh) tasks in agriculture and technology intervention to mitigate the resulting musculoskeletal disorders.

    Science.gov (United States)

    Singh, Suman; Sinwal, Neelima; Rathore, Hemu

    2012-01-01

    The lifting and carrying of loads in agriculture on small landholdings are unavoidable. Rural communities often lack access to appropriate technologies which may result in various health hazards. The objective was to study gender participation in agricultural activities involving manual material handling tasks, to assess MSDs experienced in various MMH tasks and to evaluate traditional method and designed technology. The study was conducted on 100 agricultural workers. Data on gender participation in MMH tasks in household, animal husbandry and agriculture and resulting MSDs was gathered. Pre and post assessment of technology intervention was done for NIOSH Lifting Index, QEC, and RPE. The results revealed greater susceptibility of females to musculoskeletal problems in most of the household and animal husbandry tasks. The hand trucks designed were pushing type with power grasp handle. The respondents were advised to carry 5 kg of weight per lift instead of lifting more weight in one lift/minute while filling the hand truck. By decreasing the weight and increasing the number of lifts per minute the respondents were seen falling in green zone indicating significant reduction in NIOSH lifting index. QEC scores concluded that for filling the hand truck 5 kg of weight should be carried to keep the exposure level low.

  19. A Study of the Influence of Advertising Techniques on Selection of Instructional Reading Materials by Prospective Teachers.

    Science.gov (United States)

    Greenlaw, M. Jean; And Others

    This study examined the effect of three different modes of presentation on elementary education majors' selection and rating of materials for reading instruction. Materials were chosen to represent each of the following propaganda techniques: glittering generalities, name calling, transfer, testimonial, bandwagon, and card stacking. Students in…

  20. A Guide to Selected Curriculum Materials on Interdependence, Conflict, and Change: Teacher Comments on Classroom Use and Implementation.

    Science.gov (United States)

    New York Friends Group, Inc., New York. Center for War/Peace Studies.

    The purpose of this compilation of teacher-developed descriptive evaluations of curriculum materials is to provide practical guidance to available materials dealing with the selected themes of interdependence, conflict, and change. Each of six conceptual units presented on change, conflict, identity, interdependence, power and authority, and…

  1. Cell Adhesion Selectivity of Stent Material to improve Bio-functionality by Ion Beam Modification

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jaesang; Park, JUngchan; Jung, Myunghwan; Kim, Yongki [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Park, Junkyu [Bio alpha., Co. Ltd., Gimhae (Korea, Republic of)

    2014-05-15

    In this study, ion implantation into collagen coated Co-Cr alloy, which is a cheaper material of the artificial stent product comparing with Ti alloy, has been studied to develop small diameter artificial stent by the cell adhesion control. The size of stent was 1.6mm of the diameter and 18mm of the length. The life-time of artificial stent depends on adhesion property of endothelial-cells. We successfully controlled cell adhesion selectivity between endothelial cell and muscle cell by using collagen coated and He{sup +} ion beam irradiated Co-Cr-alloy to apply to artificial stent. But, we did not achieve the inhibition of platelet adhesion, yet by using collagen coating and He{sup +} ion beam irradiation. Based on this study, we have plan to research about separation between collagen coating effect and ion beam effect. Also, we will have more detail analysis of the mechanism of cell attachment. In recent years, ion implantation has been applied to the surface modification of prosthesis to improve blood compatibility and tissue compatibility in field of biomedical application. As well known, bio compatibility was concerned with the cell adhesion selectivity for bio-functionality. The biomedical application of ion beam technology would be used more widely in the future such as catheter and artificial graft.

  2. Cell Adhesion Selectivity of Stent Material to improve Bio-functionality by Ion Beam Modification

    International Nuclear Information System (INIS)

    Lee, Jaesang; Park, JUngchan; Jung, Myunghwan; Kim, Yongki; Park, Junkyu

    2014-01-01

    In this study, ion implantation into collagen coated Co-Cr alloy, which is a cheaper material of the artificial stent product comparing with Ti alloy, has been studied to develop small diameter artificial stent by the cell adhesion control. The size of stent was 1.6mm of the diameter and 18mm of the length. The life-time of artificial stent depends on adhesion property of endothelial-cells. We successfully controlled cell adhesion selectivity between endothelial cell and muscle cell by using collagen coated and He + ion beam irradiated Co-Cr-alloy to apply to artificial stent. But, we did not achieve the inhibition of platelet adhesion, yet by using collagen coating and He + ion beam irradiation. Based on this study, we have plan to research about separation between collagen coating effect and ion beam effect. Also, we will have more detail analysis of the mechanism of cell attachment. In recent years, ion implantation has been applied to the surface modification of prosthesis to improve blood compatibility and tissue compatibility in field of biomedical application. As well known, bio compatibility was concerned with the cell adhesion selectivity for bio-functionality. The biomedical application of ion beam technology would be used more widely in the future such as catheter and artificial graft

  3. Review of Mid- to High-Temperature Solar Selective Absorber Materials

    Energy Technology Data Exchange (ETDEWEB)

    Kennedy, C. E.

    2002-07-01

    This report describes the concentrating solar power (CSP) systems using solar absorbers to convert concentrated sunlight to thermal electric power. It is possible to achieve solar absorber surfaces for efficient photothermal conversion having high solar absorptance (a) for solar radiation and a low thermal emittance (e) at the operational temperature. A low reflectance (?'' 0) at wavelengths (?) 3 mm and a high reflectance (?'' 1) at l 3 mm characterize spectrally selective surfaces. The operational temperature ranges of these materials for solar applications can be categorized as low temperature (T< 100 C), mid-temperature (100 C< T< 400 C), and high-temperature (T> 400 C). High- and mid-temperature applications are needed for CSP applications. For CSP applications, the ideal spectrally selective surface would be low-cost and easy to manufacture, chemically and thermally stable in air at elevated operating temperatures (T= 500 C), and have a solar absorptance= 0.98 and a thermal emittance= 0.05 at 500 C.

  4. Investigation of Methods for Selectively Reinforcing Aluminum and Aluminum-Lithium Materials

    Science.gov (United States)

    Bird, R. Keith; Alexa, Joel A.; Messick, Peter L.; Domack, Marcia S.; Wagner, John A.

    2013-01-01

    Several studies have indicated that selective reinforcement offers the potential to significantly improve the performance of metallic structures for aerospace applications. Applying high-strength, high-stiffness fibers to the high-stress regions of aluminum-based structures can increase the structural load-carrying capability and inhibit fatigue crack initiation and growth. This paper discusses an investigation into potential methods for applying reinforcing fibers onto the surface of aluminum and aluminum-lithium plate. Commercially-available alumina-fiber reinforced aluminum alloy tapes were used as the reinforcing material. Vacuum hot pressing was used to bond the reinforcing tape to aluminum alloy 2219 and aluminum-lithium alloy 2195 base plates. Static and cyclic three-point bend testing and metallurgical analysis were used to evaluate the enhancement of mechanical performance and the integrity of the bond between the tape and the base plate. The tests demonstrated an increase in specific bending stiffness. In addition, no issues with debonding of the reinforcing tape from the base plate during bend testing were observed. The increase in specific stiffness indicates that selectively-reinforced structures could be designed with the same performance capabilities as a conventional unreinforced structure but with lower mass.

  5. Normalization Methods and Selection Strategies for Reference Materials in Stable Isotope Analyses - Review

    International Nuclear Information System (INIS)

    Skrzypek, G.; Sadler, R.; Paul, D.; Forizs, I.

    2011-01-01

    A stable isotope analyst has to make a number of important decisions regarding how to best determine the 'true' stable isotope composition of analysed samples in reference to an international scale. It has to be decided which reference materials should be used, the number of reference materials and how many repetitions of each standard is most appropriate for a desired level of precision, and what normalization procedure should be selected. In this paper we summarise what is known about propagation of uncertainties associated with normalization procedures and propagation of uncertainties associated with reference materials used as anchors for the determination of 'true' values for δ''1''3C and δ''1''8O. Normalization methods Several normalization methods transforming the 'raw' value obtained from mass spectrometers to one of the internationally recognized scales has been developed. However, as summarised by Paul et al. different normalization transforms alone may lead to inconsistencies between laboratories. The most common normalization procedures are: single-point anchoring (versus working gas and certified reference standard), modified single-point normalization, linear shift between the measured and the true isotopic composition of two certified reference standards, two-point and multipoint linear normalization methods. The accuracy of these various normalization methods has been compared by using analytical laboratory data by Paul et al., with the single-point and normalization versus tank calibrations resulting in the largest normalization errors, and that also exceed the analytical uncertainty recommended for δ 13 C. The normalization error depends greatly on the relative differences between the stable isotope composition of the reference material and the sample. On the other hand, the normalization methods using two or more certified reference standards produces a smaller normalization error, if the reference materials are bracketing the whole range of

  6. High-temperature thermal storage systems for advanced solar receivers materials selections

    Science.gov (United States)

    Wilson, D. F.; Devan, J. H.; Howell, M.

    1990-01-01

    Advanced space power systems that use solar energy and Brayton or Stirling heat engines require thermal energy storage (TES) systems to operate continuously through periods of shade. The receiver storage units, key elements in both Brayton and Stirling systems, are designed to use the latent heat of fusion of phase-change materials (PCMs). The power systems under current consideration for near-future National Aeronautics and Space Administration space missions require working fluid temperatures in the 1100 to 1400 K range. The PCMs under current investigation that gave liquid temperatures within this range are the fluoride family of salts. However, these salts have low thermal conductivity, which causes large temperature gradients in the storage systems. Improvements can be obtained, however, with the use of thermal conductivity enhancements or metallic PCMs. In fact, if suitable containment materials can be found, the use of metallic PCMs would virtually eliminate the orbit associated temperature variations in TES systems. The high thermal conductivity and generally low volume change on melting of germanium and alloys based on silicon make them attractive for storage of thermal energy in space power systems. An approach to solving the containment problem, involving both chemical and physical compatibility, preparation of NiSi/NiSi2, and initial results for containment of germanium and NiSi/NiSi2, are presented.

  7. Ceramic Materials Selection of Fuel Crucibles based on Plasma Spray Coating for SFR

    Energy Technology Data Exchange (ETDEWEB)

    Song, Hoon; Kim, Jonghwan; Kim, Hyungtae; Ko, Youngmo; Woo, Yoonmyung; Oh, Seokjin; Kim, Kihwan; Lee, Chanbock [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2012-07-01

    The plasma-sprayed coating can provide the crucible with a denser, more friable coating layer, compared with the more friable coating layer formed by slurry-coating, which was used to prevent the interaction between melt and crucibles. Plasma-sprayed coatings are consolidated by mechanical interlocking of the molten particles impacting on the substrate and are dense by the heat applied by the plasma. The increased coating density is advantageous because it should not require frequent re coating and U-Zr melt penetration through the protective layer is more difficult in a dense coating than in a porous coating. In this study, we used Vacuum Plasma Spray method to investigate permanent coatings for re-usable crucibles for melting and casting of metallic fuel onto niobium substrates. Niobium was selected as a substrate because of its refractory nature and the coefficient of thermal expansion is similar to that of many of the candidate materials. After the HfC, ZrC, TiC, TaC, Y{sub 2}O{sub 3}, and 8% YSZ coatings were applied the resulting microstructure and chemical compositions was characterized to find the optimum process conditions for coating. Thermal plasma-sprayed coatings of refractory materials can be applied to develop a re-usable crucible coating for metallic fuel, such as the U-Zr alloy proposed for sodium cooled fast reactors.

  8. Gamma activity as a guide for the building raw materials selection and controlling the environmental hazards

    Directory of Open Access Journals (Sweden)

    T. Ibrahim

    2012-06-01

    Full Text Available The spectrometric measurements can provide an alarm for the radiation activity and radioelement concentra-tions. The activity increase over the ambient background can be achieved by well calibrated gamma-spectrometers. In comparison between Wadi El-Dahl and Abu Zawal quarries for building raw materials (feld-spar, the activity concentration of El-Dahl stream sediments are 54.5 and 44.5 Bq/kg for uranium and thorium respectively. While the activity concentration of Abu Zawal rock quarry are 167.03 and 79.77 Bq/kg for uranium and thorium respectively. These activities yielding effective dose rates of 0.63 mSv/y for Wadi El-Dahl stream sediments and 1.48 mSv/y for Abu Zawal rock quarry. In summary, the spectrometric measurements are excellent selective tool to monitoring the environment against the radiation risk. In this aspect, Wadi El-Dahl stream sedi-ment quarry considered as the more suitable for producing feldspar as a raw materials to building industry. In comparison, Abu Zawal rock quarry has a higher effective dose rate exceeds the international permissible limits which is 1 mSv/y. A total of 19 feldspar samples were completely described regarding their general chemical fea-tures by using x-ray fluorescence. From the study all the samples contain high concentration of barium and ru-bidium which can separate using different methods in order to use in different important industry.

  9. An integrated approach of topology optimized design and selective laser melting process for titanium implants materials.

    Science.gov (United States)

    Xiao, Dongming; Yang, Yongqiang; Su, Xubin; Wang, Di; Sun, Jianfeng

    2013-01-01

    The load-bearing bone implants materials should have sufficient stiffness and large porosity, which are interacted since larger porosity causes lower mechanical properties. This paper is to seek the maximum stiffness architecture with the constraint of specific volume fraction by topology optimization approach, that is, maximum porosity can be achieved with predefine stiffness properties. The effective elastic modulus of conventional cubic and topology optimized scaffolds were calculated using finite element analysis (FEA) method; also, some specimens with different porosities of 41.1%, 50.3%, 60.2% and 70.7% respectively were fabricated by Selective Laser Melting (SLM) process and were tested by compression test. Results showed that the computational effective elastic modulus of optimized scaffolds was approximately 13% higher than cubic scaffolds, the experimental stiffness values were reduced by 76% than the computational ones. The combination of topology optimization approach and SLM process would be available for development of titanium implants materials in consideration of both porosity and mechanical stiffness.

  10. Package of programs for calculating accidents involving melting of the materials in a fast-reactor vessel

    International Nuclear Information System (INIS)

    Vlasichev, G.N.

    1994-01-01

    Methods for calculating one-dimensional nonstationary temperature distribution in a system of physically coupled materials are described. Six computer programs developed for calculating accident processes for fast reactor core melt are described in the article. The methods and computer programs take into account melting, solidification, and, in some cases, vaporization of materials. The programs perform calculations for heterogeneous systems consisting of materials with arbitrary but constant composition and heat transfer conditions at material boundaries. Additional modules provide calculations of specific conditions of heat transfer between materials, the change in these conditions and configuration of the materials as a result of coolant boiling, melting and movement of the fuel and structural materials, temperature dependences of thermophysical properties of the materials, and heat release in the fuel. 11 refs., 3 figs

  11. Classical/quantum correspondence in state selective charge transfer and excitation reactions involving highly charged ions and hydrogen

    International Nuclear Information System (INIS)

    Purkait, M

    2009-01-01

    State selective charge transfer and excitation cross sections for collisions of Ne q+ (q = 1-10) with atomic hydrogen are calculated within the framework of Classical Trajectory Monte Carlo (CTMC) method and Boundary Corrected Continuum Intermediate State (BCCIS) approximation.

  12. The Relationship between 4-H Division Leaders' Propensity toward Delegation and Involvement in and Major Responsibility for Leader Identification and Selection.

    Science.gov (United States)

    Dunbar, Mary Elizabeth

    This research was to determine the relationship between New York State Cooperative Extension 4-H Division Leaders' propensity toward delegation of work responsibility and (1) their degree of involvement in the performance of leader identification and selection tasks, (2) assignment of major responsibility for these tasks, and (3) other selected…

  13. Material selection for the tool holder working under hard milling conditions using different multi criteria decision making methods

    International Nuclear Information System (INIS)

    Çalışkan, Halil; Kurşuncu, Bilal; Kurbanoğlu, Cahit; Güven, Şevki Yılmaz

    2013-01-01

    Highlights: ► The material selection problem for tool holders used in hard milling was solved. ► EXPROM2, TOPSIS and VIKOR methods were used for ranking the alternative materials. ► The weighting of criteria was performed by compromised weighting method. ► The best material for the tool holder was selected as Fe–5Cr–Mo–V aircraft steel. -- Abstract: Nowadays machining of materials in their hardened state, also called hard machining, is a challenge in production of tools and molds. It has some advantages such as lower process time and lower manufacturing cost when compared to conventional machining. In machining of hard workpiece materials, however, very high stresses act on the tool holder through the cutting tool. These stresses necessitate the tool holder to have some specific properties. Especially in hard milling, the tool holder should have high stiffness and should be able to dissipate the energy generated during interrupted cutting. Material cost of the tool holder is also important since lower costs provide a competitive advantage for manufacturers. The material selection for the tool holder should be conducted considering aforementioned requirements. To tackle the difficulty of the material selection with specific properties from a large number of alternatives, multi-criteria decision-making (MCDM) methods have been used. In this paper a decision model including extended PROMETHEE II (EXPROM2) (preference ranking organization method for enrichment evaluation), TOPSIS (technique for order performance by similarity to ideal solution) and VIKOR (VIšekriterijumsko KOmpromisno Rangiranje) methods were used for the selection of the best material for the tool holder used in hard milling. The criteria weighting was performed by compromised weighting method composed of AHP (analytic hierarchy process) and Entropy methods. The candidate materials were ranked by using these methods and the results obtained by each method were compared. It was confirmed

  14. Material selection for a constructed wetroof receiving pre-treated high strength domestic wastewater.

    Science.gov (United States)

    Zapater-Pereyra, M; van Dien, F; van Bruggen, J J A; Lens, P N L

    2013-01-01

    A constructed wetroof (CWR) is defined in this study as the combination of a green roof and a constructed wetland: a shallow wastewater treatment system placed on the roof of a building. The foremost challenge of such CWRs, and the main aim of this investigation, is the selection of an appropriate matrix capable of assuring the required hydraulic retention time, the long-term stability and the roof load-bearing capacity. Six substrata were subjected to water dynamics and destructive tests in two testing-tables. Among all the materials tested, the substratum configuration composed of sand, light expanded clay aggregates, biodegradable polylactic acid beads together with stabilization plates and a turf mat is capable of retaining the water for approximately 3.8 days and of providing stability (stabilization plates) and an immediate protection (turf mat) to the system. Based on those results, a full-scale CWR was built, which did not show any physical deterioration after 1 year of operation. Preliminary wastewater treatment results on the full-scale CWR suggest that it can highly remove main wastewater pollutants (e.g. chemical oxygen demand, PO4(3-)-P and NH4(+)-N). The results of these tests and practical design considerations of the CWR are discussed in this paper.

  15. Selective phase masking to reduce material saturation in holographic data storage systems

    Science.gov (United States)

    Phillips, Seth; Fair, Ivan

    2014-09-01

    Emerging networks and applications require enormous data storage. Holographic techniques promise high-capacity storage, given resolution of a few remaining technical issues. In this paper, we propose a technique to overcome one such issue: mitigation of large magnitude peaks in the stored image that cause material saturation resulting in readout errors. We consider the use of ternary data symbols, with modulation in amplitude and phase, and use a phase mask during the encoding stage to reduce the probability of large peaks arising in the stored Fourier domain image. An appropriate mask is selected from a predefined set of pseudo-random masks by computing the Fourier transform of the raw data array as well as the data array multiplied by each mask. The data array or masked array with the lowest Fourier domain peak values is recorded. On readout, the recorded array is multiplied by the mask used during recording to recover the original data array. Simulations are presented that demonstrate the benefit of this approach, and provide insight into the appropriate number of phase masks to use in high capacity holographic data storage systems.

  16. Why incoloy 800 was selected as tube material for the new steam generators of Doel 3

    International Nuclear Information System (INIS)

    Stubbe, J.; Wolters, F.; Somville, P.; De Ranter, K.

    1990-01-01

    Incoloy 800 or Inconel 690. This was the basic question for the SG of DOEL 3, to be replaced in 1993. A comparative evaluation was made, focused on the service behaviour, more particularly the corrosion resistance. It was concluded that both materials may be considered for SG replacement. They are indeed substantially superior to alloy 600, but none of them is really better than the other one: - they are both nearly completely immune to primary water stress corrosion cracking; - they are both susceptible to some types of attack from the secondary side. To the 690 credit are the globally better performances in the secondary side corrosion tests. However if the aggressive environments which are unlikely to occur at DOEL 3 are discarded, it appears that the margin between 690 and 800 is small. To the 800 credit is the favourable service experience except the secondary side wastage due to phosphate conditioning. 800 was finally selected not only because of favourable economic arguments, but also because of the important weight attributed to the service behaviour by the Belgian Utilities [fr

  17. Selection of nutrient used in biogenic healing agent for cementitious materials

    Science.gov (United States)

    Tziviloglou, Eirini; Wiktor, Virginie; Jonkers, Henk M.; Schlangen, Erik

    2017-06-01

    Biogenic self-healing cementitious materials target on the closure of micro-cracks with precipitated inorganic minerals originating from bacterial metabolic activity. Dormant bacterial spores and organic mineral compounds often constitute a biogenic healing agent. The current paper focuses on the investigation of the most appropriate organic carbon source to be used as component of a biogenic healing agent. It is of great importance to use an appropriate organic source, since it will firstly ensure an optimal bacterial performance in terms of metabolic activity, while it should secondly affect the least the properties of the cementitious matrix. The selection is made among three different organic compounds, namely calcium lactate, calcium acetate and sodium gluconate. The methodology that was used for the research was based on continuous and non-continuous oxygen consumption measurements of washed bacterial cultures and on compressive strength tests on mortar cubes. The oxygen consumption investigation revealed a preference for calcium lactate and acetate, but an indifferent behaviour for sodium gluconate. The compressive strength on mortar cubes with different amounts of either calcium lactate or acetate (up to 2.24% per cement weight) was not or it was positively affected when the compounds were dissolved in the mixing water. In fact, for calcium lactate the increase in compressive strength reached 8%, while for calcium acetate the maximum strength increase was 13.4%.

  18. Parallel algorithms for islanded microgrid with photovoltaic and energy storage systems planning optimization problem: Material selection and quantity demand optimization

    Science.gov (United States)

    Cao, Yang; Liu, Chun; Huang, Yuehui; Wang, Tieqiang; Sun, Chenjun; Yuan, Yue; Zhang, Xinsong; Wu, Shuyun

    2017-02-01

    With the development of roof photovoltaic power (PV) generation technology and the increasingly urgent need to improve supply reliability levels in remote areas, islanded microgrid with photovoltaic and energy storage systems (IMPE) is developing rapidly. The high costs of photovoltaic panel material and energy storage battery material have become the primary factors that hinder the development of IMPE. The advantages and disadvantages of different types of photovoltaic panel materials and energy storage battery materials are analyzed in this paper, and guidance is provided on material selection for IMPE planners. The time sequential simulation method is applied to optimize material demands of the IMPE. The model is solved by parallel algorithms that are provided by a commercial solver named CPLEX. Finally, to verify the model, an actual IMPE is selected as a case system. Simulation results on the case system indicate that the optimization model and corresponding algorithm is feasible. Guidance for material selection and quantity demand for IMPEs in remote areas is provided by this method.

  19. A Non-Ventilated Solar Façade Concept Based on Selective and Transparent Insulation Material Integration: An Experimental Study

    Directory of Open Access Journals (Sweden)

    Miroslav Čekon

    2017-06-01

    Full Text Available A new solar façade concept based on transparent insulation and a selective absorber is proposed, tested and compared with conventional insulation and a non-selective type of absorber, respectively. The presented study focuses on an experimental non-ventilated solar type of façade exposed to solar radiation both in the laboratory and in outdoor tests. Due to the high solar absorbance level of the façade, high- and low-emissivity contributions were primarily analysed. All of the implemented materials were contrasted from the thermal and optical point of view. An analysis was made of both thermodynamic and steady state procedures affecting the proposed solar façade concept. Experimental full scale tests on real building components were additionally involved during summer monitoring. An indicator of the temperature response generated by solar radiation exposure demonstrates the outdoor performance of the façade is closely related to overheating phenomena. From the thermal point of view, the proposed transparent insulation and selective absorber concept corresponds to the performance of conventional thermal insulation of identical material thickness; however, the non-selective prototype only provides 50% thermal performance. The results of the solar-based experiments show that with a small-scale experimental prototype, approximately no significant difference is measured when compared with a non-selective absorber type. The only difference was achieved at the maximum of 2.5 K, when the lower temperature was obtained in the solar selective concept. At the full-scale outdoor mode, the results indicate a maximum of 3.0 K difference, however the lower temperature achieves a non-selective approach. This solar façade can actively contribute to the thermal performance of building components during periods of heating.

  20. An analysis of teaching competence in science teachers involved in the design of context-based curriculum materials

    NARCIS (Netherlands)

    Putter - Smits, de L.G.A.; Taconis, R.; Driel, van J.H.; Jochems, W.M.G.

    2012-01-01

    The committees for the current Dutch context-based innovation in secondary science education employed teachers to design context-based curriculum materials. A study on the learning of science teachers in design teams for context-based curriculum materials is presented in this paper. In a correlation

  1. The Materials Used and the Pupils Involved in Environmental Studies and Environmental Science at GCE 'O' and 'A' Level.

    Science.gov (United States)

    Gayford, Christopher

    1984-01-01

    Discusses types of students and materials and resources used in O- and A-level environmental studies and environmental science courses. Indicates that these subjects are very susceptable to the attitudes of teachers (as shown by their willingness to produce satisfactory materials) and by the motivation of students. (JN)

  2. Joint Attention in Parent-Child Dyads Involving Children with Selective Mutism: A Comparison between Anxious and Typically Developing Children

    Science.gov (United States)

    Nowakowski, Matilda E.; Tasker, Susan L.; Cunningham, Charles E.; McHolm, Angela E.; Edison, Shannon; St. Pierre, Jeff; Boyle, Michael H.; Schmidt, Louis A.

    2011-01-01

    Although joint attention processes are known to play an important role in adaptive social behavior in typical development, we know little about these processes in clinical child populations. We compared early school age children with selective mutism (SM; n = 19) versus mixed anxiety (MA; n = 18) and community controls (CC; n = 26) on joint…

  3. Yeast 18 S rRNA Is Directly Involved in the Ribosomal Response to Stringent AUG Selection during Translation Initiation

    Czech Academy of Sciences Publication Activity Database

    Nemoto, N.; Singh, Ch. R.; Udagawa, T.; Wang, S.; Thorson, E.; Winter, Z.; Ohira, T.; Li, M.; Valášek, Leoš; Brown, S. J.; Asano, K.

    Roč. 285, č. 42 ( 2010 ), s. 32200-32212 ISSN 0021-9258 Institutional research plan: CEZ:AV0Z50200510 Keywords : START CODON SELECTION * SACCHAROMYCES-CEREVISIAE * IN-VIVO Subject RIV: EE - Microbiology, Virology Impact factor: 5.328, year: 2010

  4. Mechanical property characterization and impact resistance of selected graphite/PEEK composite materials

    Science.gov (United States)

    Baker, Donald J.

    1994-01-01

    To use graphite polyetheretherketone (PEEK) material on highly curved surfaces requires that the material be drapable and easily conformable to the surface. This paper presents the mechanical property characterization and impact resistance results for laminates made from two types of graphite/PEEK materials that will conform to a curved surface. These laminates were made from two different material forms. These forms are: (1) a fabric where each yarn is a co-mingled Celion G30-500 3K graphite fiber and PEEK thermoplastic fiber; and (2) an interleaved material of Celion G30-500 3K graphite fabric interleaved with PEEK thermoplastic film. The experimental results from the fabric laminates are compared with results for laminates made from AS4/PEEK unidirectional tape. The results indicate that the tension and compression moduli for quasi-isotropic and orthotropic laminates made from fabric materials are at least 79 percent of the modulus of equivalent laminates made from tape material. The strength of fabric material laminates is at least 80 percent of laminates made from tape material. The evaluation of fabric material for shear stiffness indicates that a tape material laminate could be replaced by a fabric material laminate and still maintain 89 percent of the shear stiffness of the tape material laminate. The notched quasi-isotropic compression panel failure strength is 42 to 46 percent of the unnotched quasi-isotropic laminate strength. Damage area after impact with 20 ft-lbs of impact energy is larger for the co-mingled panels than for the interleaved panels. The inerleaved panels have less damage than panels made from tape material. Residual compression strength of quasi-isotropic panels after impact of 20 ft-lbs of energy varies between 33 percent of the undamaged quasi-isotropic material strength for the tape material and 38 percent of the undamaged quasi-isotropic material strength for the co-mingled fabric material.

  5. Analysis of Structural and Material Aspects of Selected Elements of a Hydropneumatic Suspension System in a Passenger Car

    Directory of Open Access Journals (Sweden)

    Konieczny Ł.

    2016-03-01

    Full Text Available The article addresses results of analyses of design solutions and materials commonly used in gas springs for hydropneumatic suspension systems. The authors have discussed main advantages resulting from application of such a design solution in passenger car suspension systems. Fundamental correlations defining the parameters characterising a gas spring with constant gas mass have been referred to. Also materials used in the manufacture of selected gas spring elements have been described

  6. From so simple a beginning: Enzymatic innovation in fungus-growing ants involved a transition from individual symbiont selection to colony-level selection

    DEFF Research Database (Denmark)

    de Fine Licht, Henrik Hjarvard; Schiøtt, Morten; Boomsma, Jacobus Jan

    of the partner species. Here we document such a sequence that was connected to a major evolutionary transition in the fungus-growing ants, when the ancestor of the derived leaf-cutting ants shifted from a diet of dry vegetative material to the almost exclusive use of freshly cut leaves. This shift generated...... visible adaptations in the host ants, such as increased worker dimorphism allowing large workers to cut fresh leaves, but comparative studies of the specific fungal adaptations that accompanied the transition have not been done. Here we report the first large comparative data set on enzymatic fungus...

  7. Reviewing the Effect of Religion, Materialism and Demographic Features of the Consumer on Mental Involvement in Fashion Clothing (Case Study: Yazd

    Directory of Open Access Journals (Sweden)

    Seyed Mahdi Alhosseini Almodarresi

    2015-12-01

    Full Text Available Among the factors that are necessary to facilitate the consumer’s daily life with high mental involvement, fashion clothing is an important and significant factor for many consumers. According to the importance of the subject, this research reviewed the effect of religion, materialism and demographic features of the consumer on mental involvement in fashion clothing among citizens of Yazd. Confirmatory factor analysis method has been applied in analytical statistics of this research to determine the role and position of each one of the research elements by using Amos software. Correlation test has been used in order to review the relations between fashion clothing involvement and its dimensions, and linear regression test in order to determine the effect manner of involvement in fashion clothing and mental knowledge on confidence in fashion decision making. The statistical population includes all the individuals above 20 years old in Yazd City; the sample size was calculated 99 individuals by using Cochran formula. The research results showed that religion and materialism have significant effect on mental involvement in fashion clothing and involvement has a positive and significant effect on fashion decision making confidence. Furthermore, mental involvements in fashion clothing and mental knowledge have a positive and significant effect on fashion decision making confidence and it was specified in the reviewing of the relation between demographic factors (sex, age,… and the studied variables that the correlation between them was not significant even in the confidence level of 95 percent.

  8. An objective approach for Burkholderia pseudomallei strain selection as challenge material for medical countermeasures efficacy testing

    Directory of Open Access Journals (Sweden)

    Kristopher E. Van Zandt

    2012-09-01

    Full Text Available Burkholderia pseudomallei is the causative agent of melioidosis, a rare disease of biodefense concern with high mortality and extreme difficulty in treatment. No human vaccines are available that protect against B. pseudomallei infection, and with the current limitations of antibiotic treatment, the development of new preventative and therapeutic interventions is crucial. Although clinical trials could be used to test the efficacy of new medical countermeasures (MCMs, the high mortality rates associated with melioidosis raises significant ethical issues concerning treating individuals with new compounds with unknown efficacies. The US Food and Drug Administration (FDA has formulated a set of guidelines for the licensure of new MCMs to treat diseases in which it would be unethical to test the efficacy of these drugs in humans. The FDA Animal Rule 21 CFR 314 calls for consistent, well-characterized B. pseudomallei strains to be used as challenge material in animal models. In order to facilitate the efficacy testing of new MCMs for melioidosis using animal models, we intend to develop a well-characterized panel of strains for use. This panel will comprise of strains that were isolated from human cases, have a low passage history, are virulent in animal models, and are well characterized phenotypically and genotypically. We have reviewed published and unpublished data on various B. pseudomallei strains to establish an objective method for selecting the strains to be included in the panel of B. pseudomallei strains with attention to five categories: animal infection models, genetic characterization, clinical and passage history, and availability of the strain to the research community. We identified 109 strains with data in at least one of the five categories, scored each strain based on the gathered data and identified 6 strains as candidate for a B. pseudomallei strain panel.

  9. An objective approach for Burkholderia pseudomallei strain selection as challenge material for medical countermeasures efficacy testing.

    Science.gov (United States)

    Van Zandt, Kristopher E; Tuanyok, Apichai; Keim, Paul S; Warren, Richard L; Gelhaus, H Carl

    2012-01-01

    Burkholderia pseudomallei is the causative agent of melioidosis, a rare disease of biodefense concern with high mortality and extreme difficulty in treatment. No human vaccines are available that protect against B. pseudomallei infection, and with the current limitations of antibiotic treatment, the development of new preventative and therapeutic interventions is crucial. Although clinical trials could be used to test the efficacy of new medical countermeasures (MCMs), the high mortality rates associated with melioidosis raises significant ethical issues concerning treating individuals with new compounds with unknown efficacies. The US Food and Drug Administration (FDA) has formulated a set of guidelines for the licensure of new MCMs to treat diseases in which it would be unethical to test the efficacy of these drugs in humans. The FDA "Animal Rule" 21 CFR 314 calls for consistent, well-characterized B. pseudomallei strains to be used as challenge material in animal models. In order to facilitate the efficacy testing of new MCMs for melioidosis using animal models, we intend to develop a well-characterized panel of strains for use. This panel will comprise of strains that were isolated from human cases, have a low passage history, are virulent in animal models, and are well-characterized phenotypically and genotypically. We have reviewed published and unpublished data on various B. pseudomallei strains to establish an objective method for selecting the strains to be included in the panel of B. pseudomallei strains with attention to five categories: animal infection models, genetic characterization, clinical and passage history, and availability of the strain to the research community. We identified 109 strains with data in at least one of the five categories, scored each strain based on the gathered data and identified six strains as candidate for a B. pseudomallei strain panel.

  10. Digital Materials - Evaluation of the Possibilities of using Selected Hyperelastic Models to Describe Constitutive Relations

    Science.gov (United States)

    Mańkowski, J.; Lipnicki, J.

    2017-08-01

    The authors tried to identify the parameters of numerical models of digital materials, which are a kind of composite resulting from the manufacture of the product in 3D printers. With the arrangement of several heads of the printer, the new material can result from mixing of materials with radically different properties, during the process of producing single layer of the product. The new material has properties dependent on the base materials properties and their proportions. Digital materials tensile characteristics are often non-linear and qualify to be described by hyperelastic materials models. The identification was conducted based on the results of tensile tests models, its various degrees coefficients of the polynomials to various degrees coefficients of the polynomials. The Drucker's stability criterion was also examined. Fourteen different materials were analyzed.

  11. Digital Materials – Evaluation of the Possibilities of using Selected Hyperelastic Models to Describe Constitutive Relations

    Directory of Open Access Journals (Sweden)

    Mańkowski J.

    2017-08-01

    Full Text Available The authors tried to identify the parameters of numerical models of digital materials, which are a kind of composite resulting from the manufacture of the product in 3D printers. With the arrangement of several heads of the printer, the new material can result from mixing of materials with radically different properties, during the process of producing single layer of the product. The new material has properties dependent on the base materials properties and their proportions. Digital materials tensile characteristics are often non-linear and qualify to be described by hyperelastic materials models. The identification was conducted based on the results of tensile tests models, its various degrees coefficients of the polynomials to various degrees coefficients of the polynomials. The Drucker’s stability criterion was also examined. Fourteen different materials were analyzed.

  12. Branching enzyme assay: selective quantitation of the alpha 1,6-linked glucosyl residues involved in the branching points.

    Science.gov (United States)

    Krisman, C R; Tolmasky, D S; Raffo, S

    1985-06-01

    Methods previously described for glycogen or amylopectin branching enzymatic activity are insufficiently sensitive and not quantitative. A new, more sensitive, specific, and quantitative one was developed. It is based upon the quantitation of the glucose residues joined by alpha 1,6 bonds introduced by varying amounts of branching enzyme. The procedure involved the synthesis of a polysaccharide from Glc-1-P and phosphorylase in the presence of the sample to be tested. The branched polysaccharide was then purified and the glucoses involved in the branching points were quantitated after degradation with phosphorylase and debranching enzymes. This method appeared to be useful, not only in enzymatic activity determinations but also in the study of the structure of alpha-D-glucans when combined with those of total polysaccharide quantitation, such as iodine and phenol-sulfuric acid.

  13. A Genetics Laboratory Module Involving Selection and Identification of Lysine Synthesis Mutants in the Yeast Saccharomyces cerevisiae

    Directory of Open Access Journals (Sweden)

    Jill B. Keeney

    2009-12-01

    Full Text Available We have developed a laboratory exercise, currently being used with college sophomores, which uses the yeast Saccharomyces cerevisiae to convey the concepts of amino acid biosynthesis, mutation, and gene complementation. In brief, selective medium is used to isolate yeast cells carrying a mutation in the lysine biosynthesis pathway. A spontaneous mutation in any one of three separate genetic loci will allow for growth on selective media; however, the frequency of mutations isolated from each locus differs. Following isolation of a mutated strain, students use complementation analysis to identify which gene contains the mutation. Since the yeast genome has been mapped and sequenced, students with access to the Internet can then research and develop hypotheses to explain the differences in frequencies of mutant genes obtained.

  14. Review of US accident/incident experience involving the transportation of radioactive material (RAM) 1971-1980

    International Nuclear Information System (INIS)

    McClure, J.D.; Emerson, E.L.

    1980-01-01

    This paper analyzes the transportation accidents and incidents which have occurred in the United States in the period 1971-1980 based upon the information in the Radioactive Material Transportation Accident/Incident Data Base developed by the Transportation Technology Center (TTC) at Sandia National Laboratories. The accident/incident data base incorporates the files of the Hazardous Material Incident Report (HMIR) system operated by the Material Transportation Bureau of the US Department of Transportation (DOT) with additional information obtained from the files of the US Nuclear Regulatory Commission (NRC). A principal objective of this paper is to summarize US accident/incident experience for the past ten years, providing a concise statement of radioactive material (RAM) package failure description for the transport modes of truck, rail and air

  15. Transcriptome Analysis on Single Small Yellow Follicles Reveals That Wnt4 Is Involved in Chicken Follicle Selection

    Directory of Open Access Journals (Sweden)

    Yiya Wang

    2017-11-01

    Full Text Available Ovarian follicle selection is an important process impacting the laying performance and fecundity of hens, and is regulated by follicle-stimulating hormone (FSH through binding to its receptor [follicle-stimulating hormone receptor (FSHR]. In laying hens, the small yellow follicle (6–8 mm in diameter with the highest expression of FSHR will be recruited into the preovulatory hierarchy during ovarian follicle development. The study of molecular mechanism of chicken follicle selection is helpful for the identification of genes underlying egg-laying traits in chicken and other poultry species. Herein, the transcriptomes of chicken small yellow follicles differing in the mRNA expression of FSHR were compared, and a total of 17,993 genes were identified in 3 pairs of small yellow follicles. The Wnt signaling pathway was significantly enriched in the follicles with the greatest fold change in FSHR expression. In this pathway, the expression level of Wnt4 mRNA was significantly upregulated with a log2(fold change of 2.12. We further investigated the expression, function, and regulation of Wnt4 during chicken follicle selection and found that Wnt4 mRNA reached its peak in small yellow follicles; Wnt4 stimulated the proliferation of follicular granulosa cells (GCs, increased the expression of StAR and CYP11A1 mRNA in prehierarchical and hierarchical follicles, increased the expression of FSHR mRNA, and decreased the expression of anti-Müllerian hormone and OCLN mRNA. Treatment with FSH significantly increased Wnt4 expression in GCs. Moreover, Wnt4 facilitated the effects of FSH on the production of progesterone (P4 and the mRNA expression of steroidogenic enzyme genes in the GCs of hierarchical follicles, but inhibited the effects of FSH in the GCs of prehierarchical follicles. Collectively, these data suggest that Wnt4 plays an important role in chicken follicle selection by stimulating GC proliferation and steroidogenesis. This study provides a

  16. Effect of substrate material selection on polychromatic integral diffraction efficiency for multilayer diffractive optics in oblique incident situation

    Science.gov (United States)

    Zhang, Bo; Cui, Qingfeng; Piao, Mingxu

    2018-05-01

    The effect of substrate material selection for multilayer diffractive optical elements (MLDOEs) on polychromatic integral diffraction efficiency (PIDE) is studied in the oblique incident situation. A mathematical model of substrate material selection is proposed to obtain the high PIDE with large incident angle. The extended expression of the microstructure heights with consideration of incident angle is deduced to calculate the PIDE difference Δ η bar(λ) for different substrate material combinations. The smaller value of Δ η bar(λ) indicates the more optimal substrate material combination in a wide incident angle range. Based on the deduced mathematical model, different MLDOEs are analyzed in visible and infrared wavebands. The results show that the three-layer DOEs can be applied in larger incident angle situation than the double-layer DOEs in visible waveband. When the two substrate materials are the same, polycarbonate (PC) is more reasonable than poly(methyl methacrylate) (PMMA) as the middle filling optical material for the three-layer DOEs. In the infrared waveband, the PIDE decreases in the LWIR are obviously smaller than that in the MWIR for the same substrate material combination, and the PIDE cannot be calculated when the incident angle larger than critical angle. The analysis results can be used to guide the hybrid optical system design with MLDOEs.

  17. Engaging degradation mechanisms of materials in a tourney. An investigation into the philosophy of material selection as a mitigating measure and strategy

    OpenAIRE

    Narasimhavarman, Arasilangkumari

    2014-01-01

    Master's thesis in Offshore Technology The aim of this project is to compare some important factors such as safety and environmental aspects, life cycle costing, reliability, availability and fabrication for selecting materials for flowlines for comparative study between carbon steel as a current practice with respect to various corrosion resistance alloys as an alternatives. In order to do that it is necessary to address all possible degradation mechanisms and the conditions that intensif...

  18. Observations of parent-child co-shoppers in supermarkets: children's involvement in food selections, parental yielding, and refusal strategies.

    Science.gov (United States)

    O'Dougherty, Maureen; Story, Mary; Stang, Jamie

    2006-01-01

    The study aimed to collect descriptive information on the decision-making processes of adult shoppers around food purchases when young children are present. Anthropological field observations were conducted on adult-child grocery shoppers. Eleven supermarkets in the Minneapolis-St. Paul metropolitan region. A convenience sample (n = 142) of adult-child shoppers at 8 budget and 3 deluxe supermarkets located in diverse urban and suburban areas. Observations registered adult-child interactions over food selections, including parental yielding or refusal strategies and child engagement in shopping. Means and frequencies were calculated for food items considered. In 67 (50.4%) of the total 133 observations, a child initiated a request. Half (55.2%) of the requests were for sweets or snacks. Nearly half (47.8%) of adults yielded to the child's request. Brands and marketing techniques appeared to be a factor in 28.6% of selections. The most frequent adult refusals either provided an explanation or ignored the request. Adults yield to children's requests for sweets and snacks nearly as often as they refuse them. However, effective refusal strategies are used by many adults. Opportunities exist in the grocery store for adults to reinforce young children's interest in food and nutrition.

  19. Challenges in ensuring radiological safety and nuclear forensic for malicious acts involving nuclear and other radioactive material

    International Nuclear Information System (INIS)

    Sharma, Ranjit; Chatterjee, M.K.; Singh, Rajvir; Pradeepkumar, K.S.

    2010-01-01

    Nuclear and other radioactive materials may get smuggled into the country aimed at malicious acts. Radioactive material detected accidentally or during inspection at the entry points/national borders may indicate illicit trafficking for the purpose of nuclear/radiological terrorism. As country requires prevention and preparedness for response to these malicious acts, nuclear forensic techniques are to be developed incorporating radiological safety aspects. Nuclear forensics helps in determining the origin, intended use, legal owner and the smuggled route etc. by using fingerprinting as well as comparison with reference data. The suggested sequence of methods for analysis of radioactive material/samples will be radiological assessment, physical characterization, traditional forensic analysis, isotope analysis along with elemental/chemical analysis

  20. New screening methodology for selection of polymeric materials for transdermal drug delivery devices

    Science.gov (United States)

    Falcone, Roberto P.

    As medical advances extend the human lifespan, the level of chronic illnesses will increase and thus straining the needs of the health care system that, as a result, governments will need to balance expenses without upsetting national budgets. Therefore, the selection of a precise and affordable drug delivery technology is seen as the most practical solution for governments, health care professionals, and consumers. Transdermal drug delivery patches (TDDP) are one of the best economical technologies that are favored by pharmaceutical companies and physicians alike because it offers fewer complications when compared to other delivery technologies. TDDP provides increased efficiency, safety and convenience for the patient. The TDDP segment within the US and Global drug delivery markets were valued at 5.6 and 12.7 billion respectively in 2009. TDDP is forecasted to reach $31.5 billion in 2015. The present TDDP technology involves the fabrication of a patch that consists of a drug embedded in a polymeric matrix. The diffusion coefficient is determined from the slope of the cumulative drug release versus time. It is a trial and error method that is time and labor consuming. With all the advantages that TDDPs can offer, the methodology used to achieve the so-called optimum design has resulted in several incidents where the safety and design have been put to question in recent times (e.g. Fentanyl). A more logical screening methodology is needed. This work shows the use of a modified Duda Zielinsky equation (DZE). Experimental release curves from commercial are evaluated. The experimental and theoretical Diffusion Coefficient values are found to be within the limits specified in the patent literature. One interesting finding is that the accuracy of the DZE is closer to experimental values when the type of Molecular Shape and Radius are used. This work shows that the modified DZE could be used as an excellent screening tool to determine the optimal polymeric matrices that

  1. Archeointensities in Greece during the Neolithic period: New insights into material selection and secular variation curve

    Science.gov (United States)

    Fanjat, G.; Aidona, E.; Kondopoulou, D.; Camps, P.; Rathossi, C.; Poidras, T.

    2013-02-01

    Numerous archeomagnetic studies have provided high quality data for both the direction and the intensity of the geomagnetic field, essentially in Europe for the last 10 millennia. In particular, Greece supplies a lot of archeological materials due to its impressive cultural heritage and volcanic activity, so that numerous data have been obtained from burnt clays or historical lava flows. The most recent Greek secular variation curves are available for the last 8 millennia for the intensity and the last 6 millennia for the direction. Nevertheless, the coverage still presents several gaps for periods older than 2500 BC. In an effort to complete the Greek curve and extend it to older times, we present the archeointensity results from three Neolithic settlements in Northern Greece. The samples are of two different natures: burnt structures from Avgi (5250 ± 150 BC) and Vasili (4800 ± 200 BC), as well as ceramics from Dikili Tash (4830 ± 80 BC) and Vasili (4750 ± 250 BC). The samples have been subjected to standard rock magnetic analyses in order to estimate the thermal stability and the domain state of the magnetic carriers before archeointensity measurements. Surprisingly, very few ceramic samples provided reliable archeointensities whereas samples from burnt structures presented a very good success rate. Complementary studies showed that a detailed examination of the matrix color, following archeological information and classification standards can be a decisive test for pre-selection of sherds. In spite of these unsuccessful measurements from ceramics, we obtained an intensity value of 73.5 ± 1.1 μT for Dikili Tash, a higher value than the other data obtained in the same area, during the same period. However we do not have evidences for a technical artefact during the experiment. The burnt structures yielded two reliable archeointensities of 36.1 ± 1.8 μT and 46.6 ± 3.4 μT for Avgi and Vasili, respectively. Finally, we achieved a new archeomagnetic dating

  2. Women's empowerment and male involvement in antenatal care: analyses of Demographic and Health Surveys (DHS) in selected African countries.

    Science.gov (United States)

    Jennings, Larissa; Na, Muzi; Cherewick, Megan; Hindin, Michelle; Mullany, Britta; Ahmed, Saifuddin

    2014-08-30

    Increasing women's status and male involvement are important strategies in reducing preventable maternal morbidity and mortality. While efforts to both empower women and engage men in maternal health care-seeking can work synergistically, in practice they may result in opposing processes and outcomes. This study examines whether a woman's empowerment status, in sum and across economic, socio-familial, and legal dimensions, is associated with male partner accompaniment to antenatal care (ANC). Women's empowerment was measured based on the sum of nine empowerment items in the 2010-2011 Demographic and Health Surveys in eight sub-Saharan African countries: Burkina Faso (n = 2,490), Burundi (n = 1,042), Malawi (n = 1,353), Mozambique (n = 414), Rwanda (n = 1,211), Senegal (n = 505), Uganda (n = 428) and Zimbabwe (n = 459). In cross-sectional analyses, bivariate and multivariable logistic regressions models were used to examine the odds of male partner accompaniment to ANC between women with above-average versus below-average composite and dimensional empowerment scores. In the majority of countries, male accompaniment to ANC was not uncommon. However, findings were mixed. Positive associations in women's composite empowerment and male involvement were observed in Burkina Faso (OR = 1.27, 95% CI: 1.08, 1.50) and Uganda (OR = 1.53, 95% CI: 1.00-2.35), and in the economic empowerment dimension in Burkina Faso (OR = 1.24, 95% CI: 1.05-1.47). In Malawi, significant negative associations were observed in the odds of male accompaniment to ANC and women's composite (OR = 0.77, 95% CI: 0.62-0.97) and economic empowerment scores (OR = 0.75, 95% CI: 0.59-0.94). No significant differences were observed in Burundi, Mozambique, Rwanda, Senegal, or Zimbabwe. Women's empowerment can be positively or negatively associated with male antenatal accompaniment. Male involvement efforts may benefit from empowerment initiatives that promote women's participation in social and economic spheres

  3. Sexual and natural selection in the evolution of extended phenotypes: the use of green nesting material in starlings.

    Science.gov (United States)

    Rubalcaba, J G; Polo, V; Maia, R; Rubenstein, D R; Veiga, J P

    2016-08-01

    Although sexual selection is typically considered the predominant force driving the evolution of ritualized sexual behaviours, natural selection may also play an important and often underappreciated role. The use of green aromatic plants among nesting birds has been interpreted as a component of extended phenotype that evolved either via natural selection due to potential sanitary functions or via sexual selection as a signal of male attractiveness. Here, we compared both hypotheses using comparative methods in starlings, a group where this behaviour is widespread. We found that the use of green plants was positively related to male-biased size dimorphism and that it was most likely to occur among cavity-nesting species. These results suggest that this behaviour is likely favoured by sexual selection, but also related to its sanitary use in response to higher parasite loads in cavities. We speculate that the use of green plants in starlings may be facilitated by cavity nesting and was subsequently co-opted as a sexual signal by males. Our results represent an example of how an extended phenotypic component of males becomes sexually selected by females. Thus, both natural selection and sexual selection are necessary to fully understand the evolution of ritualized behaviours involved in courtship. © 2016 European Society For Evolutionary Biology. Journal of Evolutionary Biology © 2016 European Society For Evolutionary Biology.

  4. Chemistry {ampersand} Materials Science progress report summary of selected research and development topics, FY97

    Energy Technology Data Exchange (ETDEWEB)

    Newkirk, L.

    1997-12-01

    This report contains summaries of research performed in the Chemistry and Materials Science division. Topics include Metals and Ceramics, High Explosives, Organic Synthesis, Instrument Development, and other topics.

  5. Selective versus routine patch metal allergy testing to select bar material for the Nuss procedure in 932 patients over 10years.

    Science.gov (United States)

    Obermeyer, Robert J; Gaffar, Sheema; Kelly, Robert E; Kuhn, M Ann; Frantz, Frazier W; McGuire, Margaret M; Paulson, James F; Kelly, Cynthia S

    2018-02-01

    The aim of the study was to determine the role of patch metal allergy testing to select bar material for the Nuss procedure. An IRB-approved (11-04-WC-0098) single institution retrospective, cohort study comparing selective versus routine patch metal allergy testing to select stainless steel or titanium bars for Nuss repair was performed. In Cohort A (9/2004-1/2011), selective patch testing was performed based on clinical risk factors. In Cohort B (2/2011-9/2014), all patients were patch tested. The cohorts were compared for incidence of bar allergy and resultant premature bar loss. Risk factors for stainless steel allergy or positive patch test were evaluated. Cohort A had 628 patients with 63 (10.0%) selected for patch testing, while all 304 patients in Cohort B were tested. Over 10years, 15 (1.8%) of the 842 stainless steel Nuss repairs resulted in a bar allergy, and 5 had a negative preoperative patch test. The incidence of stainless steel bar allergy (1.8% vs 1.7%, p=0.57) and resultant bar loss (0.5% vs 1.3%, p=0.23) was not statistically different between cohorts. An allergic reaction to a stainless steel bar or a positive patch test was more common in females (OR=2.3, pbar allergies occur at a low incidence with either routine or selective patch metal allergy testing. If selective testing is performed, it is advisable in females and patients with a personal or family history of metal sensitivity. A negative preoperative patch metal allergy test does not preclude the possibility of a postoperative stainless steel bar allergy. Level III Treatment Study and Study of Diagnostic Test. Copyright © 2017 Elsevier Inc. All rights reserved.

  6. Environmental selection pressures related to iron utilization are involved in the loss of the flavodoxin gene from the plant genome.

    Science.gov (United States)

    Pierella Karlusich, Juan J; Ceccoli, Romina D; Graña, Martín; Romero, Héctor; Carrillo, Néstor

    2015-02-16

    Oxidative stress and iron limitation represent the grim side of life in an oxygen-rich atmosphere. The versatile electron transfer shuttle ferredoxin, an iron-sulfur protein, is particularly sensitive to these hardships, and its downregulation under adverse conditions severely compromises survival of phototrophs. Replacement of ferredoxin by a stress-resistant isofunctional carrier, flavin-containing flavodoxin, is a widespread strategy employed by photosynthetic microorganisms to overcome environmental adversities. The flavodoxin gene was lost in the course of plant evolution, but its reintroduction in transgenic plants confers increased tolerance to environmental stress and iron starvation, raising the question as to why a genetic asset with obvious adaptive value was not kept by natural selection. Phylogenetic analyses reveal that the evolutionary history of flavodoxin is intricate, with several horizontal gene transfer events between distant organisms, including Eukarya, Bacteria, and Archaea. The flavodoxin gene is unevenly distributed in most algal lineages, with flavodoxin-containing species being overrepresented in iron-limited regions and scarce or absent in iron-rich environments. Evaluation of cyanobacterial genomic and metagenomic data yielded essentially the same results, indicating that there was little selection pressure to retain flavodoxin in iron-rich coastal/freshwater phototrophs. Our results show a highly dynamic evolution pattern of flavodoxin tightly connected to the bioavailability of iron. Evidence presented here also indicates that the high concentration of iron in coastal and freshwater habitats may have facilitated the loss of flavodoxin in the freshwater ancestor of modern plants during the transition of photosynthetic organisms from the open oceans to the firm land. © The Author(s) 2015. Published by Oxford University Press on behalf of the Society for Molecular Biology and Evolution.

  7. A coordination polymer based magnetic adsorbent material for hemoglobin isolation from human whole blood, highly selective and recoverable

    Science.gov (United States)

    Zhang, Xiaoxing; Tan, Jipeng; Xu, Xinxin; Shi, Fanian; Li, Guanglu; Yang, Yiqiao

    2017-09-01

    A composite material has been obtained successfully through the loading of nanoscale coordination polymer on magnetic Fe3O4@SiO2 core-shell particle. In this composite material, coordination polymer nanoparticles distribute uniformly on Fe3O4@SiO2 and these two components are "tied" together firmly with chemical bonds. Adsorption experiments suggest this composite material exhibits very excellent selectivity to hemoglobin. But under the same condition, its adsorption to bovine serum albumin can almost be ignored. This selectivity can be attributed to the existence of hydrophobic interactions between coordination polymer nanoparticle and hemoglobin. For composite material, the hemoglobin adsorption process follows Langmuir model perfectly with high speed. The adsorbed hemoglobin can be eluted easily by sodium dodecyl sulfate stripping reagent with structure and biological activity of hemoglobin keeps well. The composite material was also employed to separate hemoglobin from human whole blood, which receives a very satisfactory result. Furthermore, magnetic measurement reveals ferromagnetic character of this composite material with magnetization saturation 3.56 emu g-1 and this guarantees its excellent magnetic separation performance from the treated solution.

  8. Structural in situ study of the thermal behavior of manganese dioxide materials: toward selected electrode materials for supercapacitors.

    Science.gov (United States)

    Ghodbane, Ouassim; Pascal, Jean-Louis; Fraisse, Bernard; Favier, Frédéric

    2010-12-01

    The thermal behavior of a series of MnO2 materials was investigated toward MnO2 microstructures under inert atmospheres. The byproduct formed during MnO2 heat treatments from the room temperature to 800 °C were characterized by in situ X-ray diffraction analyses. It was found that annealing spinel and ramsdellite phases caused the formation of MnO2 pyrolusite at 200 °C, Mn2O3, at 400 °C, and then Mn3O4 at higher temperatures. In the case of cryptomelane and birnessite phases, the heating process resulted in the formation of K0.51Mn0.93O2 at 600 °C, while Mn3O4 was also formed and still present up to 800 °C. Heat-treating Ni-todorokite and OMS-5 up to about 450 °C led to the formation of NiMn2O4 and NaxMnO2, respectively, and again Mn3O4 at higher temperatures. All of these structural transformations were correlated to resulting weight losses of MnO2 powders, measured by thermogravimetric analyses, during the heating process. Cyclic voltammetry measurements were performed in the presence of 0.5 M K2SO4 aqueous solution for annealed cryptomelane, K0.51Mn0.93O2, and Mn3O4-based electrodes. It was found that MnO2 cryptomelane is electrochemically stable upon heating. The long-term charge/discharge voltammetric cycling revealed that the specific capacitance of Mn3O4-based electrode is significantly improved from 14 F·g(-1) (after 20 cycles) to 123 F·g(-1) (after 500 cycles).

  9. The data acquisition system for the management of nuclear materials involved in the fabrication of MOX fuel at the Cogema plant in Cadarache

    International Nuclear Information System (INIS)

    Crousilles, M.; Beche, M.; Dalverny, G.

    2001-01-01

    This article presents the follow-up system of all the nuclear materials that are involved in the industrial process of MOX fuel fabrication. This system, called Concerto, allows the management of MOX fabrication but also of any nuclear material transfer and of the stockpile of nuclear materials with taking into account their own specificity such as the risk of criticality. Operators that intervene on the different steps of the fabrication process, supply Concerto with information so Concerto can be considered as a near real-time system providing and recording the localization, the composition, the weight, the container,... of any batch of nuclear materials. Concerto complies with the requirements of quality assurance but also of nuclear safety by forbidding any transfer whenever the maximal authorized quantity would be exceeded. (A.C.)

  10. 10 years of 1:1 taping in Belgium - A selection of murder cases involving fibre examination.

    Science.gov (United States)

    De Wael, K; Lepot, L; Lunstroot, K; Gason, F

    2016-01-01

    Since 2002, the 1:1 tape lifting technique on murder victims has been introduced in Belgium. Thirty-six murder cases for which a fibre examination was carried out in our laboratory between 2002 and 2012 are reviewed. These cases all involved the collection of microtraces on 39 victims using a 1:1 taping or similar technique, called semi 1:1 taping. The degree of "positive outcomes" for investigative and comparative fibre cases is high. Especially in cases where the modus operandi of suspects had to be verified, the examination of the 1:1 tape lifting led to very useful fibre results. The findings from some of these fibre cases are used to illustrate the advantages, drawbacks and points of interest of the two collection techniques. These are also compared with the zonal taping technique, another microtrace collection technique applied on victims at the crime scene. Copyright © 2015 The Chartered Society of Forensic Sciences. Published by Elsevier Ireland Ltd. All rights reserved.

  11. How can students contribute? A qualitative study of active student involvement in development of technological learning material for clinical skills training.

    Science.gov (United States)

    Haraldseid, Cecilie; Friberg, Febe; Aase, Karina

    2016-01-01

    Policy initiatives and an increasing amount of the literature within higher education both call for students to become more involved in creating their own learning. However, there is a lack of studies in undergraduate nursing education that actively involve students in developing such learning material with descriptions of the students' roles in these interactive processes. Explorative qualitative study, using data from focus group interviews, field notes and student notes. The data has been subjected to qualitative content analysis. Active student involvement through an iterative process identified five different learning needs that are especially important to the students: clarification of learning expectations, help to recognize the bigger picture, stimulation of interaction, creation of structure, and receiving context- specific content. The iterative process involvement of students during the development of new technological learning material will enhance the identification of important learning needs for students. The use of student and teacher knowledge through an adapted co-design process is the most optimal level of that involvement.

  12. Selection and Basic Properties of the Buffer Material for High-Level Radioactive Waste Repository in China

    Institute of Scientific and Technical Information of China (English)

    WEN Zhijian

    2008-01-01

    Radioactive wastes arising from a wide range of human activities are in many different physical and chemical forms, contaminated with varying radioactivity. Their common features are the potential hazard associated with their radioactivity and the need to manage them in such a way as to protect the human environment. The geological disposal is regarded as the most reasonable and effective way to safely disposing high-level radioactive wastes in the world. The conceptual model of geological disposal in China is based on a multi-barrier system that combines an isolating geological environment with an engineered barrier system. The buffer is one of the main engineered barriers for HLW repository. It is expected to maintain its low water permeability, self-sealing property, radio nuclides adsorption and retardation properties, thermal conductivity, chemical buffering property,canister supporting property, and stress buffering property over a long period of time. Bentonite is selected as the main content of buffer material that can satisfy the above requirements. The Gaomiaozi deposit is selected as the candidate supplier for China's buffer material of high level radioactive waste repository. This paper presents the geological features of the GMZ deposit and basic properties of the GMZ Na-bentonite. It is a super-large deposit with a high content of montmorillonite (about 75%), and GMZ-1, which is Na-bentonite produced from GMZ deposit is selected as the reference material for China's buffer material study.

  13. Radioactive characterization of the main materials involved in the titanium dioxide production process and their environmental radiological impact.

    Science.gov (United States)

    Mantero, J; Gazquez, M J; Bolivar, J P; Garcia-Tenorio, R; Vaca, F

    2013-06-01

    A study about the distribution of several radionuclides from the uranium and the thorium series radionuclides along the production process of a typical NORM industry devoted to the production of titanium dioxide has been performed. With this end the activity concentrations in raw materials, final product, co-products, and wastes of the production process have been determined by both gamma-ray and alpha-particle spectrometry. The main raw material used in the studied process (ilmenite) presents activity concentrations of around 300 Bq kg(-1) for Th-series radionuclides and 100 Bq kg(-1) for the U-series ones. These radionuclides in the industrial process are distributed in the different steps of the production process according mostly to the chemical behaviour of each radioelement, following different routes. As an example, most of the radium remains associated with the un-dissolved material waste, with activity concentrations around 3 kBq kg(-1) of (228)Ra and around 1 kBq kg(-1) of (226)Ra, while the final commercial products (TiO2 pigments and co-products) contain negligible amounts of radioactivity. The obtained results have allowed assessing the possible public radiological impact associated with the use of the products and co-products obtained in this type of industry, as well as the environmental radiological impact associated with the solid residues and liquid generated discharges. Copyright © 2013 Elsevier Ltd. All rights reserved.

  14. Physicochemical properties of aerosol released in the case of a fire involving materials used in the nuclear industry

    Energy Technology Data Exchange (ETDEWEB)

    Ouf, F.-X., E-mail: francois-xavier.ouf@irsn.fr [Institut de Radioprotection et de Sûreté Nucléaire (IRSN), PSN-RES/SCA/LPMA, PSN-RES/SCA/LECEV, Gif-Sur-Yvette 91192 (France); Mocho, V.-M.; Pontreau, S.; Wang, Z. [Institut de Radioprotection et de Sûreté Nucléaire (IRSN), PSN-RES/SCA/LPMA, PSN-RES/SCA/LECEV, Gif-Sur-Yvette 91192 (France); Ferry, D. [Aix-Marseille Université, CNRS UMR 7325, CINaM, 13009 Marseille (France); Yon, J. [CORIA-UMR 6614-Normandie Université, CNRS-Université et Insa de Rouen, Campus Universitaire du Madrillet, 76800 Saint-Etienne-du-Rouvray (France)

    2015-02-11

    Graphical abstract: - Highlights: • We characterize the aerosol emitted during thermal degradation of common materials. • Oxygen concentration on aerosol properties has been investigated. • Influence of oxygen concentration is limited to the organic carbon fraction. • The organic carbon fraction is correlated to the C:H ratio. • For pure materials, monomer diameter is correlated to the emission factor. - Abstract: For industrial concerns, and more especially for nuclear applications, the characterization of soot is essential for predicting the behaviour of containment barriers in fire conditions. This study deals with the characterization (emission factor, composition, size, morphology, microstructure) of particles produced during thermal degradation of materials found in nuclear facilities (electrical cables, polymers, oil and solvents). Small-scale experiments have been conducted for oxygen concentrations [O{sub 2}] ranging from 15% to 21% in order to imitate the oxygen depletion encountered during a confined fire. Particles denote distinct shapes, from aggregates composed of monomers with diameters ranging from 31.2 nm to 52.8 nm, to compact nanoparticles with diameters ranging from 15 nm to 400 nm, and their composition strongly depends on fuel type. Despite the organic to total carbon ratio (OC/TC), their properties are poorly influenced by the decrease in [O{sub 2}]. Finally, two empirical correlations are proposed for predicting the OC/TC ratio and the monomer diameter, respectively, as a function of the fuel's carbon to hydrogen ratio and the emission factor.

  15. Hemi-ordered nanoporous carbon electrode material for highly selective determination of nitrite in physiological and environmental systems

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Shenghai; Wu, Hongmin; Wu, Ying; Shi, Hongyan; Feng, Xun; Jiang, Shang; Chen, Jian; Song, Wenbo, E-mail: wbsong@jlu.edu.cn

    2014-08-01

    Hemi-ordered nanoporous carbon (HONC) was obtained from a mesoporous silica template through a nano-replication method using furfuryl alcohol as the carbon source. The structure and morphology of HONC were characterized and analyzed in detail by X-ray diffraction, N{sub 2}-sorption, Raman spectroscopy and transmission electron microscopy. HONC was then demonstrated as active electrode material for selective determination of nitrite in either physiological or environmental system. Well separated oxidation peaks of ascorbic acid, dopamine, uric acid and nitrite were observed in physiological system, and simultaneous discrimination of catechol, hydroquinone, resorcinol and nitrite in environmental system was also accomplished. Distinctly improved performances for selective determination of nitrite (such as significantly fast and sensitive current response with especially high selectivity) coexisted with ascorbic acid, dopamine and uric acid in the physiological system, as well as with catechol, hydroquinone and resorcinol in the environmental system were achieved at HONC electrode material. The excellent discriminating ability and high selectivity for NO{sub 2}{sup −} determination were ascribed to the good electronic conductivity, unique hemi-ordered porous structure, large surface area and large number of edge plane defect sites contained on the surface of nanopore walls of HONC. Results in this work demonstrated that HONC is one of the promising catalytic electrode materials for nitrite sensor fabrication. - Highlights: • Hemi-ordered nanoporous carbon as an active electrode material • Good discriminating ability towards NO{sub 2}{sup −} from physiological or environmental system • Highly selective determination of nitrite with fast and sensitive current response.

  16. Applications of Piezoelectric Materials in Structural Health Monitoring and Repair: Selected Research Examples.

    Science.gov (United States)

    Duan, Wen Hui; Wang, Quan; Quek, Ser Tong

    2010-12-06

    The paper reviews the recent applications of piezoelectric materials in structural health monitoring and repair conducted by the authors. First, commonly used piezoelectric materials in structural health monitoring and structure repair are introduced. The analysis of plain piezoelectric sensors and actuators and interdigital transducer and their applications in beam, plate and pipe structures for damage detection are reviewed in detail. Second, an overview is presented on the recent advances in the applications of piezoelectric materials in structural repair. In addition, the basic principle and the current development of the technique are examined.

  17. First wall and blanket module safety enhancement by material selection and design decision

    International Nuclear Information System (INIS)

    Merrill, B.J.

    1980-01-01

    A thermal/mechanical study has been performed which illustrates the behavior of a fusion reactor first wall and blanket module during a loss of coolant flow event. The relative safety advantages of various material and design options were determined. A generalized first wall-blanket concept was developed to provide the flexibility to vary the structural material (stainless steel vs titanium), coolant (helium vs water), and breeder material (liquid lithium vs solid lithium aluminate). In addition, independent vs common first wall-blanket cooling and coupled adjacent module cooling design options were included in the study. The comparative analyses were performed using a modified thermal analysis code to handle phase change problems

  18. Applications of Piezoelectric Materials in Structural Health Monitoring and Repair: Selected Research Examples

    Directory of Open Access Journals (Sweden)

    Ser Tong Quek

    2010-12-01

    Full Text Available The paper reviews the recent applications of piezoelectric materials in structural health monitoring and repair conducted by the authors. First, commonly used piezoelectric materials in structural health monitoring and structure repair are introduced. The analysis of plain piezoelectric sensors and actuators and interdigital transducer and their applications in beam, plate and pipe structures for damage detection are reviewed in detail. Second, an overview is presented on the recent advances in the applications of piezoelectric materials in structural repair. In addition, the basic principle and the current development of the technique are examined.

  19. Involving Members of the Public in Health Economics Research: Insights from Selecting Health States for Valuation to Estimate Quality-Adjusted Life-Year (QALY) Weights.

    Science.gov (United States)

    Goodwin, Elizabeth; Boddy, Kate; Tatnell, Lynn; Hawton, Annie

    2018-04-01

    Over recent years, public involvement in health research has expanded considerably. However, public involvement in designing and conducting health economics research is seldom reported. Here we describe the development, delivery and assessment of an approach for involving people in a clearly defined piece of health economics research: selecting health states for valuation in estimating quality-adjusted life-years (QALYs). This involvement formed part of a study to develop a condition-specific preference-based measure of health-related quality of life, the Multiple Sclerosis Impact Scale (MSIS-8D), and the work reported here relates to the identification of plausible, or realistic, health states for valuation. An Expert Panel of three people with multiple sclerosis (MS) was recruited from a local involvement network, and two health economists designed an interactive task that enabled the Panel to identify health states that were implausible, or unlikely to be experienced. Following some initial confusion over terminology, which was resolved by discussion with the Panel, the task worked well and can be adapted to select health states for valuation in the development of any preference-based measure. As part of the involvement process, five themes were identified by the Panel members and the researchers which summarised our experiences of public involvement in this health economics research example: proportionality, task design, prior involvement, protectiveness and partnerships. These are described in the paper, along with their practical implications for involving members of the public in health economics research. Our experience demonstrates how members of the public and health economists can work together to improve the validity of health economics research. Plain Language Summary It has become commonplace to involve members of the public in health service research. However, published reports of involving people in designing health economics research are rare. We

  20. Amorphous infinite coordination polymer microparticles: a new class of selective hydrogen storage materials

    Energy Technology Data Exchange (ETDEWEB)

    Jeon, You-Moon; Heo, Jungseok; Mirkin, Chad A [Department of Chemistry, International Institute for Nanotechnology, Northwestern University, 2145 Sheridan Road, Evanston, IL (United States); Armatas, Gerasimos S [Department of Chemistry, Northwestern University, Evanston, IL (United States); Kanatzidis, Mercouri G [Materials Science Division, Argonne National Laboratory, Argonne, IL (United States)

    2008-06-04

    A new class of micrometer-sized amorphous infinite coordination particles is selectively prepared from the coordination chemistry of a metallo-salen building block and Zn{sup 2+} ions. The particles show moderately high H{sub 2} uptake and almost no N{sub 2} adsorption, even though they are amorphous and do not have the well-defined channels typically used to explain such selectivity in metal-organic framework systems. (Abstract Copyright [2008], Wiley Periodicals, Inc.)

  1. Down Select Report of Chemical Hydrogen Storage Materials, Catalysts, and Spent Fuel Regeneration Processes

    Energy Technology Data Exchange (ETDEWEB)

    Ott, Kevin; Linehan, Sue; Lipiecki, Frank; Aardahl, Christopher L.

    2008-08-24

    The DOE Hydrogen Storage Program is focused on identifying and developing viable hydrogen storage systems for onboard vehicular applications. The program funds exploratory research directed at identifying new materials and concepts for storage of hydrogen having high gravimetric and volumetric capacities that have the potential to meet long term technical targets for onboard storage. Approaches currently being examined are reversible metal hydride storage materials, reversible hydrogen sorption systems, and chemical hydrogen storage systems. The latter approach concerns materials that release hydrogen in endothermic or exothermic chemical bond-breaking processes. To regenerate the spent fuels arising from hydrogen release from such materials, chemical processes must be employed. These chemical regeneration processes are envisioned to occur offboard the vehicle.

  2. the art of preview in appropriate teaching/learning material selection

    African Journals Online (AJOL)

    USER

    Abstract. This study recognised the importance of print materials and texts in effective and ... As previewers, they ought to look into the external and internal .... detailed information, the reading techniques will change to suit the purposes.

  3. Assessment of the quality of test results from selected civil engineering material testing laboratories in Tanzania

    CSIR Research Space (South Africa)

    Mbawala, SJ

    2017-12-01

    Full Text Available Civil and geotechnical engineering material testing laboratories are expected to produce accurate and reliable test results. However, the ability of laboratories to produce accurate and reliable test results depends on many factors, among others...

  4. Selection of Easily Accessible PCR- and Bio-Compatible Materials for Microfluidic Chips

    KAUST Repository

    Xiao, Kang

    2013-10-30

    Conventional fabrication of microfluidic chip is a complicated and time, effort and material consuming process. Consequently, due to high expenses, it has poor applicability for performing mass biological analysis by microfluidics. In this study, we repor

  5. Selection of Easily Accessible PCR- and Bio-Compatible Materials for Microfluidic Chips

    KAUST Repository

    Xiao, Kang; Kodzius, Rimantas; Wu, Jinbo

    2013-01-01

    Conventional fabrication of microfluidic chip is a complicated and time, effort and material consuming process. Consequently, due to high expenses, it has poor applicability for performing mass biological analysis by microfluidics. In this study, we

  6. Materials selection for long life in LEO: a critical evaluation of atomic oxygen testing with thermal atom systems

    International Nuclear Information System (INIS)

    Koontz, S.L.; Kuminecz, J.; Leger, L.; Nordine, P.

    1988-01-01

    The use of thermal atom test methods as a materials selection and screening technique for low-Earth orbit (LEO) spacecraft is critically evaluated. The chemistry and physics of thermal atom environments are compared with the LEO environment. The relative reactivities of a number of materials determined to be in thermal atom environments are compared to those observed in LEO and in high quality LEO simulations. Reaction efficiencies measured in a new type of thermal atom apparatus are one-hundredth to one-thousandth those observed in LEO, and many materials showing nearly identical reactivities in LEO show relative reactivities differing by as much as a factor of 8 in thermal atom systems. A simple phenomenological kinetic model for the reaction of oxygen atoms with organic materials can be used to explain the differences in reactivity in different environments. Certain specific thermal test environments can be used as reliable materials screening tools. Using thermal atom methods to predict material lifetime in LEO requires direct calibration of the method against LEO data or high quality simulation data for each material

  7. Material and Energy Flows Associated with Select Metals in GREET 2. Molybdenum, Platinum, Zinc, Nickel, Silicon

    Energy Technology Data Exchange (ETDEWEB)

    Benavides, Pahola T. [Argonne National Lab. (ANL), Argonne, IL (United States); Dai, Qiang [Argonne National Lab. (ANL), Argonne, IL (United States); Sullivan, John L. [Argonne National Lab. (ANL), Argonne, IL (United States); Kelly, Jarod C. [Argonne National Lab. (ANL), Argonne, IL (United States); Dunn, Jennifer B. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2015-09-01

    In this work, we analyzed the material and energy consumption from mining to production of molybdenum, platinum, zinc, and nickel. We also analyzed the production of solar- and semiconductor-grade silicon. We described new additions to and expansions of the data in GREET 2. In some cases, we used operating permits and sustainability reports to estimate the material and energy flows for molybdenum, platinum, and nickel, while for zinc and silicon we relied on information provided in the literature.

  8. Heavy Metals and Radioactive Characterization of the Main Materials Involved in the HC-FeMn Alloy Production Process

    Energy Technology Data Exchange (ETDEWEB)

    Badran, H. [Taif University (Saudi Arabia); Bakr, H.; Elnimr, T. [Tanta University (Egypt); Sharshar, T. [Kafrelsheikh University (Egypt)

    2014-07-01

    Natural occurring radioactive materials (NORM) are always present in association with a variety of elements in the geological formations. The extraction of non-radioactive minerals from the mineral matrices may lead to the buildup of NORM in wastes and/or end product with different concentrations of uranium and thorium daughters, depending on extraction procedures, initial concentrations and chemical forms of the NORM in the mineral matrices. Gamma-ray spectrometry was used for the quantitative assessment of radionuclides and the associated radiation hazards at the high carbon Ferromanganese alloy (HC-FeMn) production plant in Abu Zenima (West Sinai, Egypt). The low grad Mn from Um Bogma is mixed with Norwegian Mn to improve its quality. While the Egyptian raw Mn is richer in {sup 238}U, Cu and Zn, the Norwegian raw Mn is richer in {sup 40}K and Mn. The mixing process leads to increasing concentrations of {sup 226}Ra and Zn. Enhanced concentrations of Mn, Cu and Zn were also found in the waste. The radioactivity concentrations of {sup 226}Ra, {sup 232}Th and {sup 40}K in different raw materials used in the alloy formation process, HC-FeMn alloy, waste and other mining products produced by the same company are also determined. The estimated range of the total activities of wastes produced annually by the extraction process are 8.7-17.3, 0.7-1.3 and 6.7-13.4 GBq for {sup 226}Ra, {sup 232}Th and {sup 40}K, respectively. The calculated absorbed dose rate and the annual effective dose equivalent in waste dumps with these increased fractions of NORM are 225 nGy/h and 276 mSv, respectively. This investigation does not recommend the use of the waste in housing construction or as filling materials in the area where houses may be built on or near the tailing piles. Document available in abstract form only. (authors)

  9. Selection and authentication of botanical materials for the development of analytical methods.

    Science.gov (United States)

    Applequist, Wendy L; Miller, James S

    2013-05-01

    Herbal products, for example botanical dietary supplements, are widely used. Analytical methods are needed to ensure that botanical ingredients used in commercial products are correctly identified and that research materials are of adequate quality and are sufficiently characterized to enable research to be interpreted and replicated. Adulteration of botanical material in commerce is common for some species. The development of analytical methods for specific botanicals, and accurate reporting of research results, depend critically on correct identification of test materials. Conscious efforts must therefore be made to ensure that the botanical identity of test materials is rigorously confirmed and documented through preservation of vouchers, and that their geographic origin and handling are appropriate. Use of material with an associated herbarium voucher that can be botanically identified is always ideal. Indirect methods of authenticating bulk material in commerce, for example use of organoleptic, anatomical, chemical, or molecular characteristics, are not always acceptable for the chemist's purposes. Familiarity with botanical and pharmacognostic literature is necessary to determine what potential adulterants exist and how they may be distinguished.

  10. [Study on material base of Carthamus tinctorius with antioxidant effect based on selective knock-out].

    Science.gov (United States)

    Wang, Lin-Yan; Tang, Yu-Ping; Liu, Xin; Ge, Ya-Hui; Li, Shu-Jiao; Shang, Er-Xin; Duan, Jin-Ao

    2014-04-01

    To establish a method for studying efficacious materials of traditional Chinese medicines from an overall perspective. Carthamus tinctorius was taken the example. Its major components were depleted by preparing liquid chromatography. Afterwards, the samples with major components depleted were evaluated for their antioxidant effect, so as to compare and analyze the major efficacious materials of C. tinctorius with antioxidant activity and the contributions. Seven major components were depleted from C. tinctorius samples, and six of them were identified with MS data and control comparison. After all of the samples including depleted materials are compared and evaluated for their antioxidant effect, the findings showed that hydroxysafflor yellow A, anhydrosafflor yellow B and 6-hydroxykaempferol-3, 6-di-O-glucoside-7-O-glucuronide were the major efficacious materials. This study explored a novel and effective method for studying efficacious materials of traditional Chinese medicines. Through this method, we could explain the direct and indirect contributions of different components to the efficacy of traditional Chinese medicines, and make the efficacious material expression of traditional Chinese medicines clearer.

  11. Effects of terrestrial UV radiation on selected outdoor materials: an interdisciplinary approach

    Science.gov (United States)

    Heikkilä, A.; Kazadzis, S.; Tolonen-Kivimäki, O.; Meinander, O.; Lindfors, A.; Lakkala, K.; Koskela, T.; Kaurola, J.; Sormanen, A.; Kärhä, P.; Naula-Iltanen, A.; Syrjälä, S.; Kaunismaa, M.; Juhola, J.; Ture, T.; Feister, U.; Kouremeti, N.; Bais, A.; Vilaplana, J. M.; Rodriguez, J. J.; Guirado, C.; Cuevas, E.; Koskinen, J.

    2009-08-01

    Modern polymeric materials possess an ever increasing potential in a large variety of outdoor objects and structures offering an alternative for many traditional materials. In outdoor applications, however, polymers are subject to a phenomenon called weathering. This is primarily observed as unwanted property changes: yellowing or fading, chalking, blistering, and even severe erosion of the material surface. One of the major weathering factors is UV radiation. In spring 2005, the Finnish Meteorological Institute with its research and industrial partners launched a five-year material research project named UVEMA (UV radiation Effects on MAterials). Within the framework of the project, a weathering network of seven European sites was established. The network extends from the Canary Islands of Spain (latitude 28.5°N) to the Lapland of Finland (latitude 67.4°N), covering a wide range of UV radiation conditions. Since autumn 2005, the sites of the network have been maintaining weathering platforms of specimens of different kinds of polymeric materials. At the same time, the sites have been maintaining their long-term monitoring programmes for spectrally resolved UV radiation. Within UVEMA, these data are used for explaining the differences between the degradation rates of the materials at each site and for correlating the UV conditions in accelerated ageing tests to those under the Sun. We will present the objectives of the UVEMA project aiming at deeper understanding of the ageing of polymers and more reliable assessments for their service life time. Methodologies adopted within the project and the first results of the project will be summarized.

  12. Effect of Selected Alternative Fuels and Raw Materials on the Cement Clinker Quality

    Directory of Open Access Journals (Sweden)

    Strigáč Július

    2015-11-01

    Full Text Available The article deals with the study of the effects of alternative fuels and raw materials on the cement clinker quality. The clinker quality was expressed by the content of two principal minerals alite C3S and belite C2S. The additions of alternative fuels ashes and raw materials, in principle, always increased the belite content and conversely reduced the amount of alite. The alternative fuels with high ash content were used such as the meat-bone meal, sewage sludge from sewage treatment plants and paper sludge and the used alternative raw materials were metallurgical slags - granulated blastfurnace slag, air cooled blastfurnace slag and demetallized steel slag, fluidized bed combustion fly ash and waste glass. Meat-bone meal, sewage sludge from sewage treatment plants and paper sludge were evaluated as moderately suitable alternative fuels which can be added in the amounts of 2.8 wt. % addition of meat-bone meals ash, 3.64 wt. % addition of sewage sludge ash and 3.8 wt. % addition of paper sludge ash to the cement raw mixture. Demetallised steel slag is suitable for production of special sulphate resistant cement clinker for CEM I –SR cement with addition up to 5 wt. %. Granulated blastfurnace slag is a suitable alternative raw material with addition 4 wt. %. Air cooled blastfurnace slag is a suitable alternative raw material with addition 4.2 wt. %. Waste glass is not very appropriate alternative raw material with addition only 1.16 wt. %. Fluidized bed combustion fly ash appears not to be equally appropriate alternative raw material for cement clinker burning with less potential utilization in the cement industry and with addition 3.41 wt. %, which forms undesired anhydrite CaSO4 in the cement clinker.

  13. Radiation tests on selected electrical insulating materials for high-power and high voltage application

    International Nuclear Information System (INIS)

    Liptak, G.; Schuler, R.; Haberthuer, B.; Mueller, H.; Zeier, W.; Maier, P.; Schoenbacher, H.

    1985-01-01

    This report presents a comprehensive set of test results on the irradiation of insulating materials and systems used for the windings of rotating machines, dry-type transformers, and magnet coils. The materials were: Novolac, bisphenol-A, and cycloaliphatic types of epoxy; saturated and unsaturated polyesterimide; silicone, phenolic, and acrylic resins. The reinforcement consisted of glass mat, glass roving, glass cloth, mica paper, polyester mat, polyester roving, polyester cloth, aromatic polyamide paper, or combinations thereof. The materials were irradiated in an 8 MW pool reactor up to integrated doses of 10 8 Gy. On most samples, flexural properties were examined as recommended by IEC Standard 544. For tapes and varnishes, the breakdown voltage was measured. The adhesion of copper bars glued together with an epoxy resin was examined by means of a lap-shear test. A cupping test by means of the Erichsen apparatus was used to measure the flexibility of varnishes. The results are presented in tables and graphs for each of the materials tested. Those from mechanical tests show that the radiation resistance of composite resin-rich insulations depends not only on the base resin combination and the reinforcement material but, to a large degree, also on the adhesion between the two. It appears that better adhesion, and consequently higher radiation resistance, is obtained by special surface treatments of glass fibres. For laminates, higher radiation resistance is obtained with glass mat and resin combinations than with glass cloth as reinforcing materials. The breakdown voltage tests show that the application of mechanical stress to most irradiated samples causes the insulation layer to crack, resulting in lower dielectric strength. For a number of materials, the critical properties of flexural strength and breakdown voltage are above 50% of the initial value at doses between 10 7 and 10 8 Gy, i.e. a radiation index of 7 to 8 at 10 5 Gy/h. (orig.)

  14. Characterization of Emissions from Building Products: Selection Criteria, Storage and Handling of Indoor Materials for Experiments

    DEFF Research Database (Denmark)

    Kjær, Ulla Dorte; Nielsen, Peter A.; Marcussen, Lis

    1996-01-01

    In research projects it is usually impossible to study more than a very limited aount of different products. Care and consideration must therefore be taken in the selection. The following criteria were used to select five products for chemical and sensory emission testing: The products should...... be indoor climate relevant, meaning that they should be in direct contact with indoor air when used in buildings, and their emission should contribute significantly to the indoor air concentrations for instance due to a large surface area. They should be representative in terms of being widely used, now...... that the emission mechanisms do not change as a consequence of physical processes or chemical reactions. The five products selected were PVC flooring, waterborne varnish on beechwood parquet, carpet, sealant, and waterborne paint on gypsum board. The products were brought to the laboratory immediately after...

  15. Dentist Material Selection for Single-Unit Crowns: Findings from The National Dental Practice-Based Research Network

    Science.gov (United States)

    Makhija, Sonia K.; Lawson, Nathaniel C.; Gilbert, Gregg H.; Litaker, Mark S.; McClelland, Jocelyn A.; Louis, David R.; Gordan, Valeria V.; Pihlstrom, Daniel J.; Meyerowitz, Cyril; Mungia, Rahma; McCracken, Michael S.

    2016-01-01

    Objectives Dentists enrolled in the National Dental Practice-Based Research Network completed a study questionnaire about techniques and materials used for single-unit crowns and an enrollment questionnaire about dentist/practice characteristics. The objectives were to quantify dentists’ material recommendations and test the hypothesis that dentist’s and practice’s characteristics are significantly associated with these recommendations. Methods Surveyed dentists responded to a contextual scenario asking what material they would use for a single-unit crown on an anterior and posterior tooth. Material choices included: full metal, porcelain-fused-to-metal (PFM), all-zirconia, layered zirconia, lithium disilicate, leucite-reinforced ceramic, or other. Results 1,777 of 2,132 eligible dentists responded (83%). The top 3 choices for anterior crowns were lithium disilicate (54%), layered zirconia (17%), and leucite-reinforced glass ceramic (13%). There were significant differences (p<0.05) by dentist’s gender, race, years since graduation, practice type, region, practice busyness, hours worked/week, and location type. The top 3 choices for posterior crowns were all-zirconia (32%), PFM (31%), and lithium disilicate (21%). There were significant differences (p<0.05) by dentist’s gender, practice type, region, practice busyness, insurance coverage, hours worked/week, and location type. Conclusions Network dentists use a broad range of materials for single-unit crowns for anterior and posterior teeth, adopting newer materials into their practices as they become available. Material choices are significantly associated with dentist’s and practice’s characteristics. Clinical Significance Decisions for crown material may be influenced by factors unrelated to tooth and patient variables. Dentists should be cognizant of this when developing an evidence-based approach to selecting crown material. PMID:27693778

  16. Ultrastructural changes of cell walls under intense mechanical treatment of selective plant raw material

    International Nuclear Information System (INIS)

    Bychkov, Aleksey L.; Ryabchikova, E.I.; Korolev, K.G.; Lomovsky, O.I.

    2012-01-01

    Structural changes of cell walls under intense mechanical treatment of corn straw and oil-palm fibers were studied by electron and light microscopy. Differences in the character of destruction of plant biomass were revealed, and the dependence of destruction mechanisms on the structure of cell walls and lignin content was demonstrated. We suggest that the high reactivity of the particles of corn straw (about 18% of lignin) after intense mechanical treatment is related to disordering of cell walls and an increase of the surface area, while in the case of oil palm (10% of lignin) the major contribution into an increase in the reactivity is made by an increase of surface area. -- Highlights: ► Structure of cell walls determines the processes of plant materials' destruction. ► Ultrastructure of highly lignified materials strongly disordering by mechanical action. ► Ultrastructure of low-lignified materials is not disordering by mechanical action.

  17. Mesoporous material grafted with luminescent molecules for the design of selective metal ion chemosensor

    International Nuclear Information System (INIS)

    Zhang Huidong; Zhang Ping; Ye Kaiqi; Sun Yinghui; Jiang Shimei; Wang Yue; Pang Wenqin

    2006-01-01

    Luminescent Schiff-base groups have been successfully grafted on the surface of mesoporous material MCM-48. The grafted Schiff-base groups were employed to prepare luminescent Schiff-base-Zn complex that was covalently bound to the MCM-48 surface. These luminescent mesoporous materials were characterized with X-ray, UV-VIS and emission spectroscopic methods. Experimental results demonstrated that MCM-48 modified with functional groups exhibited novel luminescent property. The chemosensing property of modified MCM-48 sample was investigated. It was demonstrated that the fluorescence of MCM-48 solid with Schiff-base groups could be completely quenched by Cu 2+ cation and this mesoporous material was suitable for sensing Cu 2+ cation in aqueous media

  18. Methodology for the selection of routes for international cross-border line projects involving multiple objectives and decision-makers in the analyses of restrictions and environmental possibilities

    International Nuclear Information System (INIS)

    Angel S, Enrique; Cadena, Luis Fernando

    2005-01-01

    A scheme was developed and applied to select the optimum environmental route for international cross-border line projects, in a decision making context involving multiple objectives and multiple decision-makers, the project studied was the electricity interconnection for central America (SIEPAC) for which a prospective assessment was carried out regarding the restrictions and possibilities in the light of the Colombian environmental dimensions management model. The methodology proposed followed these stages: Definition and approval of the structure of environmental restriction and criticality variables, sectorization and selection of complex sections, definition of decision-makers for multi-objective analysis; design and application of consultation tool; definition and modeling of options applying SIG; sensitivity analysis of alternative routes and project's environment management. Different options were identified for insertion and permanence of the project according to the criteria of various interest groups and actors consulted: environmental authorities, electricity companies, scientific community and civil society

  19. Natural selection drives the fine-scale divergence of a coevolutionary arms race involving a long-mouthed weevil and its obligate host plant

    Directory of Open Access Journals (Sweden)

    Toju Hirokazu

    2009-01-01

    Full Text Available Abstract Background One of the major recent advances in evolutionary biology is the recognition that evolutionary interactions between species are substantially differentiated among geographic populations. To date, several authors have revealed natural selection pressures mediating the geographically-divergent processes of coevolution. How local, then, is the geographic structuring of natural selection in coevolutionary systems? Results I examined the spatial scale of a "geographic selection mosaic," focusing on a system involving a seed-predatory insect, the camellia weevil (Curculio camelliae, and its host plant, the Japanese camellia (Camellia japonica. In this system, female weevils excavate camellia fruits with their extremely-long mouthparts to lay eggs into seeds, while camellia seeds are protected by thick pericarps. Quantitative evaluation of natural selection demonstrated that thicker camellia pericarps are significantly favored in some, but not all, populations within a small island (Yakushima Island, Japan; diameter ca. 30 km. At the extreme, camellia populations separated by only several kilometers were subject to different selection pressures. Interestingly, in a population with the thickest pericarps, camellia individuals with intermediate pericarp thickness had relatively high fitness when the potential costs of producing thick pericarps were considered. Also importantly, some parameters of the weevil - camellia interaction such as the severity of seed infestation showed clines along temperature, suggesting the effects of climate on the fine-scale geographic differentiation of the coevolutionary processes. Conclusion These results show that natural selection can drive the geographic differentiation of interspecific interactions at surprisingly small spatial scales. Future studies should reveal the evolutionary/ecological outcomes of the "fine scale geographic mosaics" in biological communities.

  20. Selection of engineering materials and fabrication of liquid metal fast breeder reactors

    International Nuclear Information System (INIS)

    Patriarca, P.

    1975-01-01

    Information is presented graphically and pictorially concerning the need for nuclear power; basic nuclear concepts including BWR, PWR, HTGR, and LMFBR; the fissioning process; nuclear reactor fuel; fabrication of reactor vessels for LMFBR's; fabrication of intermediate heat exchangers for LMFBR's; piping fabrication for LMFBR's; transition welds; steam generators for LMFBR demonstration plants worldwide; stress corrosion cracking of steam generator materials and weldments; post--test examination of the Alco/BLH sodium-heated steam generator; alternate steam generator designs; and alternate structural materials. (DCC)

  1. Computational Modelling of Materials for Wind Turbine Blades: Selected DTUWind Energy Activities

    DEFF Research Database (Denmark)

    Mikkelsen, Lars Pilgaard; Mishnaevsky, Leon

    2017-01-01

    Computational and analytical studies of degradation of wind turbine blade materials at the macro-, micro-, and nanoscale carried out by the modelling team of the Section Composites and Materials Mechanics, Department of Wind Energy, DTU, are reviewed. Examples of the analysis of the microstructural...... effects on the strength and fatigue life of composites are shown. Computational studies of degradation mechanisms of wind blade composites under tensile and compressive loading are presented. The effect of hybrid and nanoengineered structures on the performance of the composite was studied...

  2. Computational Modelling of Materials for Wind Turbine Blades: Selected DTU Wind Energy Activities.

    Science.gov (United States)

    Mikkelsen, Lars Pilgaard; Mishnaevsky, Leon

    2017-11-08

    Computational and analytical studies of degradation of wind turbine blade materials at the macro-, micro-, and nanoscale carried out by the modelling team of the Section Composites and Materials Mechanics, Department of Wind Energy, DTU, are reviewed. Examples of the analysis of the microstructural effects on the strength and fatigue life of composites are shown. Computational studies of degradation mechanisms of wind blade composites under tensile and compressive loading are presented. The effect of hybrid and nanoengineered structures on the performance of the composite was studied in computational experiments as well.

  3. In situ corrosion studies on selected high level waste packaging materials under simulated disposal conditions in rock salt

    International Nuclear Information System (INIS)

    Smailos, E.; Schwarzkopf, W.; Koester, R.

    1988-01-01

    In order to qualify corrosion resistant materials for high level waste (HLW) packagings acting as a long-term barrier in a rock salt repository, the corrosion behavior of preselected materials is being investigated in laboratory-scale and in-situ experiments. This work reports about in-situ corrosion experiments on unalloyed steels, Ti 99.8-Pd, Hastelloy C4, and iron-base alloys, as nodular cast iron, Ni-Resist D4 and Si-cast iron, under simulated disposal conditions. The results of the investigations can be summarized as follows: (1) all materials investigated exhibited high resistance to corrosion under the conditions prevailing in the Brine Migration Test; (2) all materials and above all the materials with passivating oxide layers such as Ti 99.8-Pd and Hastelloy C4 which may corrode selectively already in the presence of minor amounts of brine had been resistant with respect to any type of local corrosion attack; the gamma-radiation of 3 · 10 2 Gy/h did not exert an influence on the corrosion behavior of the materials

  4. Selected Bibliography of Egyptian Educational Materials, Vol. 2, No. 3, 1976.

    Science.gov (United States)

    Al-Ahram Center for Scientific Translations, Cairo (Egypt).

    The selective annotated bibliography of Egyptian educational publications contains 109 entries on 42 topics. Included are journal articles, books, and government documents published during 1976. Content includes the following topics: adult education, art education, audiovisual aids, care for distinguished students, educational planning,…

  5. Selected Bibliography of Egyptian Educational Materials, Vol. 2, No. 2, 1976.

    Science.gov (United States)

    Al-Ahram Center for Scientific Translations, Cairo (Egypt).

    One hundred fourteen entries on 58 topics are contained in the selective annotated bibliography of Egyptian publications on education. Included are journal articles, books, and government documents published during 1976. Content includes the following topics: adult education, Arabic language, audiovisual aids, child upbringing, civics, economics…

  6. Selected Bibliography of Egyptian Educational Materials, Vol. 2, No. 1, 1976.

    Science.gov (United States)

    Al-Ahram Center for Scientific Translations, Cairo (Egypt).

    This selective annotated bibliography of Egyptian publications on education contains 126 entries on 55 topics. Publications include journal articles, books, and government documents published during 1976 or late 1975. Among the 55 topics are the following: adult education, agricultural schools, art education, child upbringing, compulsory…

  7. Selected Bibliography of Egyptian Educational Materials, Vol. 2, No. 4, 1976.

    Science.gov (United States)

    Al-Ahram Center for Scientific Translations, Cairo (Egypt).

    One hundred seventy entries on 69 topics are contained in the selective annotated bibliography of Egyptian publications on education. Included are journal articles, books, and government documents published during 1976. Content includes the following topics: Arabic language, art education, civics, commercial schools, comparative education,…

  8. Thermal comfort characteristics of some selected building materials in the regional setting of Ile-Ife, Nigeria

    Directory of Open Access Journals (Sweden)

    S. K. Fasogbon

    2015-07-01

    Full Text Available In Ile-Ife, it is very common to see quite a lot of local people engaging in mud bricks moulding, concrete block making, mud house construction and the bricklaying profession in general. These have particular bearing on the economy and the political situation of the people involved as in the profession there is set of rules and regulations guiding the rate and procedure for carrying out any such moulding or construction work. Considering the importance of this, the present study investigated the thermal performance of some selected building materials in the ancient city of Ile-Ife in Nigeria. The work demonstrated how a building envelope responds to outdoor conditions through graphic illustrations. This was followed by constructing three physical building models, with model 1 constructed of mud bricks, model 2 constructed of concrete blocks and model 3 constructed of cast concrete. Each of the models was first roofed with galvanised Iron roofing sheets, later with aluminium roofing sheets and finally with asbestos roofing. Readings were taken by inserting TGP-4500 Data loggers into appropriate positions. The results showed that internal temperatures in the mud-brick and cast concrete buildings remained fairly stable despite external diurnal fluctuations. Humidity data collected also showed that fluctuations in external humidity levels do not affect humidity levels within the mud-brick and cast concrete structures significantly. On the other hand, the structure made of concrete blocks responded more to external fluctuations in temperature and humidity. Moreover, humidity levels in the cast concrete building were the least, followed by those in the mud-brick house; while the concrete block structure had the highest level of humidity. It was also discovered that aluminium roofing gave the highest internal temperature, followed by galvanised iron roofing and the least was seen with asbestos roofing. For external diurnal fluctuations, building model

  9. Guidelines for Selecting Control and Treatment Options for Contaminated Dredged Material.

    Science.gov (United States)

    1986-09-01

    is being used to predict surface runoff water quality from dredged material as part of the CE/EPA FVP ( Westerdahl and Skogerboe 1981, Lee and...April 20, 1984. Water Pollution Control Federation. 1976. "Chlorination of Wastewater," Manual of Practice No. 4, Washington, D.C. Westerdahl , H. E

  10. Assessing the Impact of Removing Select Materials from Coal Mine Overburden, Central Appalachia Region, USA

    Science.gov (United States)

    The exposure of readily soluble components of overburden materials from surface coal mining to air and water results in mineral oxidation and carbonate mineral dissolution, thus increasing coal mine water conductivity. A conductivity benchmark of 300 µS/cm for mine water dischar...

  11. Challenges of selecting materials for the process of biomass gasification in supercritical water

    Energy Technology Data Exchange (ETDEWEB)

    Boukis, N.; Habicht, W.; Hauer, E.; Dinjus, E. [Karlsruher Institut fuer Technologie (KIT), Karlsruhe (Germany). Inst. fuer Technische Chemie

    2010-07-01

    A new process for the gasification of wet biomass is the reaction in supercritical water. The product is a combustible gas, rich in hydrogen with a high calorific value. The reaction is performed under high temperatures - up to 700 C - and pressures up to 30 MPa. The combination of these physical conditions and the corrosive environment is very demanding for the construction materials of the reactor. Only few alloys exhibit the required mechanical properties, especially the mechanical strength at temperatures higher than 600 C. Ni-Base alloys like alloy 625 can be applied up to a temperature of 700 C and are common materials for application under supercritical water conditions. During gasification experiments with corn silage and other biomasses, corrosion of the reactor material alloy 625 appears. The gasification of an aqueous methanol solution in supercritical water at temperatures up to 600 C and 25 - 30 MPa pressure results in an product gas rich in hydrogen, carbon dioxide and some methane. Alloy 625 shows very low corrosion rates in this environment. It is obvious that the heteroatoms and salts present in biomass cause corrosion of the reactor material. (orig.)

  12. Instrumental neutron and photon activation analyses of selected geochemical reference materials

    Czech Academy of Sciences Publication Activity Database

    Mizera, Jiří; Řanda, Zdeněk

    2010-01-01

    Roč. 284, č. 1 (2010), s. 157-163 ISSN 0236-5731 R&D Projects: GA AV ČR IAA300130706 Institutional research plan: CEZ:AV0Z10480505 Keywords : neutron activation analysis * photon activation analysis * geochemical reference materials Subject RIV: BG - Nuclear, Atomic and Molecular Physics, Colliders Impact factor: 0.777, year: 2010

  13. Instrumental neutron and photon activation analyses of selected geochemical reference materials

    Czech Academy of Sciences Publication Activity Database

    Mizera, Jiří; Řanda, Z.

    2010-01-01

    Roč. 284, č. 1 (2010), s. 157-163 ISSN 0236-5731 Institutional research plan: CEZ:AV0Z30460519 Keywords : neutron activation analysis * photon activation analysis * geochemical reference materials Subject RIV: BG - Nuclear, Atomic and Molecular Physics, Colliders OBOR OECD: Analytical chemistry Impact factor: 0.777, year: 2010

  14. Selected Bibliography of Egyptian Educational Materials. Vol. 5, No. 2, 1979.

    Science.gov (United States)

    Al-Ahram Center for Scientific Translations, Cairo (Egypt).

    One hundred and forty two books, articles, and government publications dealing with education in Egypt are cited in this annotated bibliography. Items cited were published in 1979 and examine education for all age groups and ability levels. The material is presented under 84 headings including adult education, art education, children's books,…

  15. Selected Bibliography of Egyptian Educational Materials. Vol. 3, No. 4, 1977.

    Science.gov (United States)

    Al-Ahram Center for Scientific Translations, Cairo (Egypt).

    Over 130 citations of books, journals, government publications, and newspapers dealing with education in Egypt are included in this annotated bibliography. Materials cited were published in 1977. Sixty-two alphabetically arranged categories cover such topics as agricultural schools, Arabic language, basic education, child care, curricula,…

  16. Analytical review of minimum critical mass values for selected uranium and plutonium materials

    International Nuclear Information System (INIS)

    Morman, J.A.; Henrikson, D.J.; Garcia, A.S.

    1997-01-01

    Current subcritical limits for a number of uranium and plutonium materials (metals and compounds) as given in the ANSI/ANS standards for criticality safety are based on evaluations performed in the late 1970s and early 1980s. This paper presents the results of an analytical study of the minimum critical mass values for a set of materials using current codes and standard cross section sets. This work is meant to produce a consistent set of minimum critical mass values that can form the basis for adding new materials to the single-parameter tables in ANSI/ANS-8.1. Minimum critical mass results are presented for bare and water reflected full-density spheres and for full density moist (1.5 wt-% water) as calculated with KENO-Va, MCNP4A and ONEDANT. Calculations were also performed for both dry and moist materials at one-half density. Some KENO calculations were repeated using several cross section sets to examine potential bias differences. The results of the calculations were compared to the currently accepted subcritical limits. The calculated minimum critical mass values are reasonably consistent for the three codes, and differences most likely reflect differences in the cross section sets. The results are also consistent with values given in ANSI/ANS-8.1. 3 refs., 2 tabs

  17. Selection of environmental sustainable fiber materials for wind turbine blades - a contra intuitive process?

    Energy Technology Data Exchange (ETDEWEB)

    Birkved, M.; Corona, A. [Technical Univ. of Denmark. DTU Management Engineering, Kgs. Lyngby (Denmark); Markussen, C.M.; Madsen, Bo [Technical Univ. of Denmark. DTU Wind Energy, Risoe Campus, Roskilde (Denmark)

    2013-09-01

    Over the recent decades biomaterials have been marketed successfully supported by the common perception that biomaterials and environmental sustainability de facto represents two sides of the same coin. The development of sustainable composite materials such as blades for small-scale wind turbines have thus partially been focused on the substitution of conventional fiber materials with bio-fibers. The major question is if this material substitution actually, is environmental sustainable. In order to assess a wide pallet of environmental impacts and taking into account positive and negative environmental trade-offs over the entire life-span of composite materials, life cycle assessment (LCA) can be applied. In the present case study, four different types of fibers (carbon, glass, flax and carbon/flax mixture) are compared in terms of environmental sustainability and cost. Applying one of the most recent life cycle impact assessment methods, it is demonstrated that the environmental sustainability of the mixed carbon/flax fiber based composite material is better than that of the flax fibers alone. This observation may be contra-intuitive, but is mainly caused by the fact that the bio-material resin demand is by far exceeding the resin demand of the conventional fibers, and since the environmental burden of the resin is comparable to that of the fibers, resin demand is in terms of environmental sustainability important. On the other hand is the energy demand and associated environmental impacts in relation to the production of the carbon and glass fibers considerable compared to the impacts resulting from resin production. The ideal fiber solution, in terms of environmental sustainability, is hence the fiber composition having the lowest resin demand and lowest overall energy demand. The optimum environmental solution hence turns out to be a 70:30 flax:carbon mix, thereby minimizing the use of carbon fibers and resin. On top of the environmental sustainability

  18. Materialism.

    Science.gov (United States)

    Melnyk, Andrew

    2012-05-01

    Materialism is nearly universally assumed by cognitive scientists. Intuitively, materialism says that a person's mental states are nothing over and above his or her material states, while dualism denies this. Philosophers have introduced concepts (e.g., realization and supervenience) to assist in formulating the theses of materialism and dualism with more precision, and distinguished among importantly different versions of each view (e.g., eliminative materialism, substance dualism, and emergentism). They have also clarified the logic of arguments that use empirical findings to support materialism. Finally, they have devised various objections to materialism, objections that therefore serve also as arguments for dualism. These objections typically center around two features of mental states that materialism has had trouble in accommodating. The first feature is intentionality, the property of representing, or being about, objects, properties, and states of affairs external to the mental states. The second feature is phenomenal consciousness, the property possessed by many mental states of there being something it is like for the subject of the mental state to be in that mental state. WIREs Cogn Sci 2012, 3:281-292. doi: 10.1002/wcs.1174 For further resources related to this article, please visit the WIREs website. Copyright © 2012 John Wiley & Sons, Ltd.

  19. Selective propensity of bovine jugular vein material to bacterial adhesions: An in-vitro study.

    Science.gov (United States)

    Jalal, Zakaria; Galmiche, Louise; Lebeaux, David; Villemain, Olivier; Brugada, Georgia; Patel, Mehul; Ghigo, Jean-Marc; Beloin, Christophe; Boudjemline, Younes

    2015-11-01

    Percutaneous pulmonary valve implantation (PPVI) using Melody valve made of bovine jugular vein is safe and effective. However, infective endocarditis has been reported for unclear reasons. We sought to assess the impact of valvular substrates on selective bacterial adhesion. Three valved stents (Melody valve, homemade stents with bovine and porcine pericardium) were tested in-vitro for bacterial adhesion using Staphylococcus aureus and Streptococcus sanguinis strains. Bacterial adhesion was higher on bovine jugular venous wall for S. aureus and on Melody valvular leaflets for S. sanguinis in control groups and significantly increased in traumatized Melody valvular leaflets with both bacteria (traumatized vs non traumatized: p=0.05). Bacterial adhesion was lower on bovine pericardial leaflets. Selective adhesion of S. aureus and S. sanguinis pathogenic strains to Melody valve tissue was noted on healthy tissue and increased after implantation procedural steps. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

  20. Chemical-technological approach to the selection of ceramic materials with predetermined thermistor properties

    Energy Technology Data Exchange (ETDEWEB)

    Plewa, J.; Altenburg, H. [Fachhochschule Muenster, Steinfurt (Germany). SIMa and Supraleiter-Keramik-Kristalle; Brunner, M. [Fachhochschule Koeln (Germany). Elektronische Bauelemente; Shpotyuk, O.; Vakiv, M. [Scientific Research Co. ' ' Carat' ' , Lviv Scientific Research Inst. of Materials, Lviv (Ukraine)

    2002-07-01

    The selection possibilities of quaternary Cu-Ni-Co-Mn oxide system restricted by cubic spinels (CuMn{sub 2}O{sub 4}, MnCo{sub 2}O{sub 4} and NiMn{sub 2}O{sub 4}) for NTC thermistors application were discussed. Phase compositions, microstructural features and electrical properties of the investigated spinel-structured ceramics were studied in tight connection with technological regimes of their sintering. (orig.)