Miniature electron bombardment evaporation source: evaporation rate measurement

International Nuclear Information System (INIS)

Nehasil, V.; Masek, K.; Matolin, V.; Moreau, O.

1997-01-01

Miniature electron beam evaporation sources which operate on the principle of vaporization of source material, in the form of a tip, by electron bombardment are produced by several companies specialized in UHV equipment. These sources are used primarily for materials that are normally difficult to deposit due to their high evaporation temperature. They are appropriate for special applications such as heteroepitaxial thin film growth requiring a very low and well controlled deposition rate. A simple and easily applicable method of evaporation rate control is proposed. The method is based on the measurement of ion current produced by electron bombardment of evaporated atoms. The absolute evaporation flux values were measured by means of the Bayard-Alpert ion gauge, which enabled the ion current vs evaporation flux calibration curves to be plotted. (author). 1 tab., 4 figs., 6 refs

Dating Howardite Melt Clasts: Evidence for an Extended Vestan Bombardment?

Science.gov (United States)

Cartwright, J. A.; Hodges, K. V.; Wadhwa, M.; Mittlefehldt, D. W.

2016-01-01

Howardites are polymict breccias that, together with eucrites and diogenites (HED), likely originate from the vestan surface (regolith/ megaregolith), and display a heterogeneous distribution of eucritic and diogenitic material. Melt clasts are also present alongside other regolithic features within howardites, and are noteworthy for their compositional variability and appearance. Melt clasts formed by impact events provide a snapshot of the timings and conditions of surface gardening and bombardment on the vestan surface. By dating such clasts, we aim to better constrain the timings of impact events on Vesta, and to establish whether the impact flux in the asteroid belt was similar to that on the Moon. As the Moon is used as the basis for characterising impact models of the inner solar system, it is necessary to verify that apparent wide-scale events are seen in other planetary bodies. In particular, the observed clustering of Apollo melt clast ages between 3.8-4.0 Ga has led to two hypotheses: 1) The Moon was subjected to a sudden event - 'Lunar Cataclysm' or period of 'Late Heavy Bombardment' (LHB), 2) The age cluster represents the end of an epoch of declining bombardment or 'Heavy Bombardment. No consensus has emerged regarding one or other hypothesis. We are testing these hypotheses by seeking evidence for such events in materials other than those derived from the Moon.

An ion beam deceleration lens for ultra-low-energy ion bombardment of naked DNA

Energy Technology Data Exchange (ETDEWEB)

Thopan, P.; Prakrajang, K. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thongkumkoon, P. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand); Suwannakachorn, D. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Yu, L.D., E-mail: yuldyuld@gmail.com [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand)

2013-07-15

Highlights: ► An ion beam deceleration lens was designed and constructed. ► The deceleration lens was installed and tested. ► The decelerated ion beam energy was measured using an electrical field. ► Decelerated ultra-low-energy ion beam bombarded naked DNA. ► Ion beam with energy of a few tens of eV could break DNA strands. -- Abstract: Study of low-energy ion bombardment effect on biological living materials is of significance. High-energy ion beam irradiation of biological materials such as organs and cells has no doubt biological effects. However, ion energy deposition in the ion-bombarded materials dominantly occurs in the low-energy range. To investigate effects from very-low-energy ion bombardment on biological materials, an ion beam deceleration lens is necessary for uniform ion energy lower than keV. A deceleration lens was designed and constructed based on study of the beam optics using the SIMION program. The lens consisted of six electrodes, able to focus and decelerate primary ion beam, with the last one being a long tube to obtain a parallel uniform exiting beam. The deceleration lens was installed to our 30-kV bioengineering-specialized ion beam line. The final decelerated-ion energy was measured using a simple electrostatic field to bend the beam to range from 10 eV to 1 keV controlled by the lens parameters and the primary beam condition. In a preliminary test, nitrogen ion beam at 60 eV decelerated from a primary 20-keV beam bombarded naked plasmid DNA. The original DNA supercoiled form was found to change to relaxed and linear forms, indicating single or double strand breaks. The study demonstrated that the ion bombardment with energy as low as several-tens eV was possible to break DNA strands and thus potential to cause genetic modification of biological cells.

An ion beam deceleration lens for ultra-low-energy ion bombardment of naked DNA

International Nuclear Information System (INIS)

Thopan, P.; Prakrajang, K.; Thongkumkoon, P.; Suwannakachorn, D.; Yu, L.D.

2013-01-01

Highlights: ► An ion beam deceleration lens was designed and constructed. ► The deceleration lens was installed and tested. ► The decelerated ion beam energy was measured using an electrical field. ► Decelerated ultra-low-energy ion beam bombarded naked DNA. ► Ion beam with energy of a few tens of eV could break DNA strands. -- Abstract: Study of low-energy ion bombardment effect on biological living materials is of significance. High-energy ion beam irradiation of biological materials such as organs and cells has no doubt biological effects. However, ion energy deposition in the ion-bombarded materials dominantly occurs in the low-energy range. To investigate effects from very-low-energy ion bombardment on biological materials, an ion beam deceleration lens is necessary for uniform ion energy lower than keV. A deceleration lens was designed and constructed based on study of the beam optics using the SIMION program. The lens consisted of six electrodes, able to focus and decelerate primary ion beam, with the last one being a long tube to obtain a parallel uniform exiting beam. The deceleration lens was installed to our 30-kV bioengineering-specialized ion beam line. The final decelerated-ion energy was measured using a simple electrostatic field to bend the beam to range from 10 eV to 1 keV controlled by the lens parameters and the primary beam condition. In a preliminary test, nitrogen ion beam at 60 eV decelerated from a primary 20-keV beam bombarded naked plasmid DNA. The original DNA supercoiled form was found to change to relaxed and linear forms, indicating single or double strand breaks. The study demonstrated that the ion bombardment with energy as low as several-tens eV was possible to break DNA strands and thus potential to cause genetic modification of biological cells

The effects of thermal annealing on iron bombarded InP/InGaAs multilayer structures

International Nuclear Information System (INIS)

Subramaniam, S.C.; Rezazadeh, A.A.

2006-01-01

The effects of Fe-ion bombardment at 77 K (cold) and room temperature (RT) into single layer InGaAs, InP and multilayer InP/InGaAs HBT structures have been investigated. Annealing characteristics and RF dissipation loss measurements of Fe-ion bombarded samples at 77 K indicated good electrical isolation in n-, p-type InGaAs materials and InP/InGaAs HBT structures. Thermally stable (up to 250 deg. C) high sheet resistance (R sh ) of ∼5 x 10 6 Ω/sq has been achieved on these samples while higher R sh of ∼10 7 Ω/sq was obtained for the n-InP materials bombarded with similar conditions. Dissipation losses of 1.7 dB/cm at 10 GHz and 2.8 dB/cm at 40 GHz have been measured for the cold Fe-ion bombarded InP-based HBT structures. This result is similar to those obtained for an un-bombarded S.I. InP substrate, indicating good electrical isolation. We have also determined electron trapping levels by thermal annealing for the cold and RT Fe-ion bombarded samples. It is shown that the high resistivity achieved in the cold implanted InGaAs layer is most likely due to the creation of mid-bandgap defect levels (E C - 0.33) eV, which are created only in the cold Fe-ion bombardment. The DC isolation and RF dissipation loss analysis have been used to identify a suitable bombardment scheme for the fabrication of planar InP/InGaAs HBTs

Ultra-low-energy (<10 eV/u) ion beam bombardment effect on naked DNA

Energy Technology Data Exchange (ETDEWEB)

Thopan, P. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thongkumkoon, P. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Department of Biology, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Prakrajang, K. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Faculty of Science, Maejo University, Chiang Mai 50290 (Thailand); Suwannakachorn, D. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Yu, L.D., E-mail: yuld@thep-center.org [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand)

2014-05-01

Highlights: • Decelerated ultra-low energy ion beam bombarded naked DNA. • DNA form change induced by ion bombardment was investigated. • N-ion bombardment at 32 eV induced DNA single and double strand breaks. • Ar-ion bombardment at a-few-hundreds eV induced DNA single strand break. - Abstract: Since ion energy deposition in the ion-bombarded materials dominantly occurs in the low-energy range, it is very interesting to know effects from ultra-low-energy ion interaction with DNA for understanding ion-beam-induced genetic mutation. Tens-keV Ar- and N-ion beams were decelerated to ultra-low energy ranging from 20 to 100 eV, or only a few to 10 eV/u, to bombard naked plasmid DNA. The bombarded DNA was analyzed using gel electrophoresis for DNA form changes. The original DNA supercoiled form was found to change to relaxed and linear forms, indicating single or double strand breaks after bombarded by tens-eV ion beam. N-ion beam was found more effective in inducing DNA change and mutation than Ar-ion beam. The study demonstrated that the ion bombardment with energy as low as several-tens eV was able to break DNA strands and thus potentially to cause genetic modification of biological cells. The experimental results were discussed in terms of direct atomic collision between the ions and DNA atoms.

Ultra-low-energy (<10 eV/u) ion beam bombardment effect on naked DNA

International Nuclear Information System (INIS)

Thopan, P.; Thongkumkoon, P.; Prakrajang, K.; Suwannakachorn, D.; Yu, L.D.

2014-01-01

Highlights: • Decelerated ultra-low energy ion beam bombarded naked DNA. • DNA form change induced by ion bombardment was investigated. • N-ion bombardment at 32 eV induced DNA single and double strand breaks. • Ar-ion bombardment at a-few-hundreds eV induced DNA single strand break. - Abstract: Since ion energy deposition in the ion-bombarded materials dominantly occurs in the low-energy range, it is very interesting to know effects from ultra-low-energy ion interaction with DNA for understanding ion-beam-induced genetic mutation. Tens-keV Ar- and N-ion beams were decelerated to ultra-low energy ranging from 20 to 100 eV, or only a few to 10 eV/u, to bombard naked plasmid DNA. The bombarded DNA was analyzed using gel electrophoresis for DNA form changes. The original DNA supercoiled form was found to change to relaxed and linear forms, indicating single or double strand breaks after bombarded by tens-eV ion beam. N-ion beam was found more effective in inducing DNA change and mutation than Ar-ion beam. The study demonstrated that the ion bombardment with energy as low as several-tens eV was able to break DNA strands and thus potentially to cause genetic modification of biological cells. The experimental results were discussed in terms of direct atomic collision between the ions and DNA atoms

Study on evolution of gases from fluoropolymer films bombarded with heavy ions

International Nuclear Information System (INIS)

Minamisawa, Renato Amaral; Zimmerman, Robert Lee; Budak, Satilmis; Ila, Daryush

2008-01-01

Ion beam bombardment provides a unique way of material modification by inducing a high degree of localized electronic excitation. The ion track, or affected volume along the ion path through the material is related to the total damage and possible structural changes. Here we study the evolution of gases emitted by poly(tetrafluorethylene-co-perfluoro-(propyl vinyl ether)) (PFA) fluoropolymer bombarded with MeV gold ions. The gas was monitored by a residual gas analyzer (RGA), as a function of the ion fluence. Micro-Raman, atomic force microscopy and optical absorption were used to analyze the chemical structure changes and sputtering yield

Diffusion processes in bombardment-induced surface topography

International Nuclear Information System (INIS)

Robinson, R.S.

1984-01-01

The bombardment of surfaces with moderate energy ions can lead to the development of various micron-sized surface structures. These structures include ridges, ledges, flat planes, pits and cones. The causal phenomena in the production of these features are sputtering, ion reflection, redeposition of sputtered material, and surface diffusion of both impurity and target-atom species. The authors concentrate on the formation of ion bombardment-induced surface topography wherein surface diffusion is a dominant process. The most thoroughly understood aspect of this topography development is the generation of cone-like structures during sputtering. The formation of cones during sputtering has been attributed to three effects. These are: (1) the presence of asperities, defects, or micro-inclusions in the surface layers, (2) the presence of impurities on the surfaces, and (3) particular crystal orientations. (Auth.)

The new generations of power components will depend on neutron and/or electron bombardment techniques

International Nuclear Information System (INIS)

Lilen, H.

1976-01-01

Neutron and electron bombardment techniques for materials doping, newly introduced in the fabrication of power semiconductor components: diodes, transistors, thyristors, and triacs are briefly outlined. A neutron bombardment of high purity silicon results in a short-lived 31 Si isotope (from 30 Si) decaying into 31 P. The phosphorus with its five peripheral electrons induces a negative doping (N), and the neutron technique gives a homogeneous doping. Furthermore, silicon bombardment with 1 to 2MeV electrons induces micro-ruptures in the lattice, that act as recombination traps reducing carrier lifetimes. Consequently, gold diffusion techniques can be replaced by electron bombardment with a gain in controlling carrier lifetimes [fr

Computer simulation of the topography evolution on ion bombarded surfaces

CERN Document Server

Zier, M

2003-01-01

The development of roughness on ion bombarded surfaces (facets, ripples) on single crystalline and amorphous homogeneous solids plays an important role for example in depth profiling techniques. To verify a faceting mechanism based not only on sputtering by directly impinging ions but also on the contribution of reflected ions and the redeposition of sputtered material a computer simulation has been carried out. The surface in this model is treated as a two-dimensional line segment profile. The model describes the topography evolution on ion bombarded surfaces including the growth mechanism of a facetted surface, using only the interplay of reflected and primary ions and redeposited atoms.

Ion bombardment modification of surfaces

International Nuclear Information System (INIS)

Auciello, O.

1984-01-01

An historical overview of the main advances in the understanding of bombardment-induced surface topography is presented. The implantation and sputtering mechanisms which are relevant to ion bombardment modification of surfaces and consequent structural, electronic and compositional changes are described. Descriptions of plasma and ion-beam sputtering-induced film formation, primary ion-beam deposition, dual beam techniques, cluster of molecule ion-beam deposition, and modification of thin film properties by ion bombardment during deposition are presented. A detailed account is given of the analytical and computational modelling of topography from the viewpoint of first erosion theory. Finally, an account of the possible application and/or importance of textured surfaces in technologies and/or experimental techniques not considered in previous chapters is presented. refs.; figs.; tabs

Adhesion of silver films to ion-bombarded alumina

International Nuclear Information System (INIS)

Erck, R.A.; Fenske, G.R.

1990-01-01

This paper reports on silver films deposited on alumina substrates using ion bombardment. Adhesion strength was measured as a function of deposition conditions, sputter-cleaning time, and bombarding ion species, using a pull-type adhesion tester. Argon- and argon/oxygen-ion sputtering produced large increases in adhesion strength, with the greatest increases occurring for oxygen-ion bombardment. Adhesion strength increased monotonically as a function of ion sputtering time. At a given deposition rate, further enhancement of adhesion is seen with concurrent ion bombardment

Bombardment of gas molecules on single graphene layer at high temperature

Energy Technology Data Exchange (ETDEWEB)

Murugesan, Ramki [School of Mechanical and Aerospace Engineering, Gyeongsang National University, Jinju, Gyeongnam 660-701 (Korea, Republic of); Park, Jae Hyun [Department of Aerospace and System Engineering and Research Center for Aircraft Parts Technology, Gyeongsang National University, Jinju, Gyeongnam 660-701 (Korea, Republic of); Ha, Dong Sung [Future Propulsion Center, Agency for Defense Development, Daejeon 305-600 (Korea, Republic of)

2014-12-09

Graphite is widely used as a material for rocket-nozzle inserts due to its excellent thermo-physical properties as well as low density. During the operation of rockets, the surface of the graphite nozzle is subjected to very high heat fluxes and the undesirable erosion of the surface occurs due to the bombardment of gas molecules with high kinetic energy, which causes a significant reduction of nozzle performance. However, the understanding and quantification of such bombardment is not satisfactory due to its complexity: The bond breaking-forming happens simultaneously for the carbon atoms of graphene, some gas molecules penetrate through the surface, some of them are reflected from the surface, etc. In the present study, we perform extensive molecular dynamics (MD) simulations to examine the bombardment phenomena in high temperature environment (several thousand Kelvin). Advanced from the previous studies that have focused on the bombardment by light molecules (e.g., H{sub 2}), we will concentrate on the impact by realistic molecules (e.g., CO{sub 2} and H{sub 2}O). LAMMPS is employed for the MD simulations with NVE ensemble and AIREBO potential for graphene. The molecular understanding of the interaction between graphene and highly energetic gas molecules will enable us to design an efficient thermo-mechanical protection system.

Surface roughening under ion bombardment

International Nuclear Information System (INIS)

Bhatia, C.S.

1982-01-01

Ion bombardment can cause roughening of a surface. Inadequate step coverage and poor adhesion of films on such surfaces are of concern. An extreme case of surface roughening results in cone formation under ion bombardment. The results of the investigation, using scanning electron microscopy, is discussed in terms of the role of (a) embedded particles, (b) impurities and (c) surface migration in cone formation on the target surface. (Auth.)

Beryllium dust generation resulting from plasma bombardment

International Nuclear Information System (INIS)

Doerner, R.; Mays, C.

1997-01-01

The beryllium dust resulting from erosion of beryllium samples subjected to plasma bombardment has been measured in PISCES-B. Loose surface dust was found to be uniformly distributed throughout the device and accounts for 3% of the eroded material. A size distribution measurement of the loose surface dust shows an increasing number of particles with decreasing diameter. Beryllium coatings on surfaces with a line of sight view of the target interaction region account for an additional 33% of the eroded beryllium material. Flaking of these surface layers is observed and is thought to play a significant role in dust generation inside the vacuum vessel. (orig.)

Mechanisms of ion-bombardment-induced DNA transfer into bacterial E. coli cells

Energy Technology Data Exchange (ETDEWEB)

Yu, L.D., E-mail: yuld@thep-center.org [Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand); Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Sangwijit, K. [Molecular Biology Laboratory, Department of Biology, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Prakrajang, K. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Faculty of Science, Maejo University, Chiang Mai 50290 (Thailand); Phanchaisri, B. [Institute of Science and Technology Research, Chiang Mai University, Chiang Mai 50200 (Thailand); Thongkumkoon, P. [Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand); Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thopan, P. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Singkarat, S. [Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand); Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Anuntalabhochai, S. [Molecular Biology Laboratory, Department of Biology, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand)

2014-05-01

Highlights: • Ion bombardment could induce DNA transfer into E. coli cells. • The DNA transfer induction depended on ion energy and fluence. • The mechanism was associated with the bacterial cell envelope structure. • A mechanism phase diagram was proposed to summarize the mechanism. - Abstract: As a useful ion beam biotechnology, ion-bombardment-induced DNA transfer into bacterial Escherichia coli (E. coli) cells has been successfully operated using argon ions. In the process ion bombardment of the bacterial cells modifies the cell envelope materials to favor the exogenous DNA molecules to pass through the envelope to enter the cell. The occurrence of the DNA transfer induction was found ion energy and fluence dependent in a complex manner. At ion energy of a few keV and a few tens of keV to moderate fluences the DNA transfer could be induced by ion bombardment of the bacterial cells, while at the same ion energy but to high fluences DNA transfer could not be induced. On the other hand, when the ion energy was medium, about 10–20 keV, the DNA transfer could not be induced by ion bombardment of the cells. The complexity of the experimental results indicated a complex mechanism which should be related to the complex structure of the bacterial E. coli cell envelope. A phase diagram was proposed to interpret different mechanisms involved as functions of the ion energy and fluence.

Mechanisms of ion-bombardment-induced DNA transfer into bacterial E. coli cells

International Nuclear Information System (INIS)

Yu, L.D.; Sangwijit, K.; Prakrajang, K.; Phanchaisri, B.; Thongkumkoon, P.; Thopan, P.; Singkarat, S.; Anuntalabhochai, S.

2014-01-01

Highlights: • Ion bombardment could induce DNA transfer into E. coli cells. • The DNA transfer induction depended on ion energy and fluence. • The mechanism was associated with the bacterial cell envelope structure. • A mechanism phase diagram was proposed to summarize the mechanism. - Abstract: As a useful ion beam biotechnology, ion-bombardment-induced DNA transfer into bacterial Escherichia coli (E. coli) cells has been successfully operated using argon ions. In the process ion bombardment of the bacterial cells modifies the cell envelope materials to favor the exogenous DNA molecules to pass through the envelope to enter the cell. The occurrence of the DNA transfer induction was found ion energy and fluence dependent in a complex manner. At ion energy of a few keV and a few tens of keV to moderate fluences the DNA transfer could be induced by ion bombardment of the bacterial cells, while at the same ion energy but to high fluences DNA transfer could not be induced. On the other hand, when the ion energy was medium, about 10–20 keV, the DNA transfer could not be induced by ion bombardment of the cells. The complexity of the experimental results indicated a complex mechanism which should be related to the complex structure of the bacterial E. coli cell envelope. A phase diagram was proposed to interpret different mechanisms involved as functions of the ion energy and fluence

Quantification of steroid conjugates using fast atom bombardment mass spectrometry

International Nuclear Information System (INIS)

Gaskell, S.J.

1990-01-01

Fast atom bombardment/mass spectrometry or liquid secondary ion mass spectrometry provides the capability for direct analysis of steroid conjugates (sulfates, glucuronides) without prior hydrolysis or derivatization. During the analysis of biologic extracts, limitations on the sensitivity of detection arise from the presence of co-extracted material which may suppress or obscure the analyte signal. A procedure is described for the quantitative determination of dehydroepiandrosterone sulfate in serum which achieved selective isolation of the analyte using immunoadsorption extraction and highly specific detection using tandem mass spectrometry. A stable isotope-labeled analog [( 2H2]dehydroepiandrosterone sulfate) was used as internal standard. Fast atom bombardment of dehydroepiandrosterone sulfate yielded abundant [M-H]- ions that fragmented following collisional activation to give HSO4-; m/z 97. During fast atom bombardment/tandem mass spectrometry of serum extracts, a scan of precursor ions fragmenting to give m/z 97 detected dehydroepiandrosterone sulfate and the [2H2]-labeled analog with a selectivity markedly superior to that observed using conventional mass spectrometry detection. Satisfactory agreement was observed between quantitative data obtained in this way and data obtained by gas chromatography/mass spectrometry of the heptafluorobutyrates of dehydroepiandrosterone sulfate and [2H2]dehydroepiandrosterone sulfate obtained by direct derivatization. 21 refs

Sputtering and reflection of self-bombardment of tungsten material

International Nuclear Information System (INIS)

Niu, Guo-jian; Li, Xiao-chun; Xu, Qian; Yang, Zhong-shi; Luo, Guang-nan

2015-01-01

In present research, the sputtering and reflection yield of self-bombardment of tungsten are investigated with the aid of molecular dynamics simulations. The source of sputtered and reflected atoms is detected by traced the original locations of sputtered and reflected atoms. Results show that for the reflected atoms no specific region exists which means cluster atoms are randomly reflected. But almost all of sputtered atoms are from a conical region under the landing point of cluster. So we can determine the sputtering yield by study the dimension of the sputtering region. Molecular dynamics shows the depth and radius of the conical are power functions of impacting energy. The effects of cluster size and temperature of target on sputtering and reflection rate are also preformed in present study. Both sputtering and reflection yield are proportion to cluster size in present cluster size, i.e. 66–2647 atoms. Higher target temperature can increase sputtering yield and deduce sputtering threshold energy, but little effect on reflection rate

Sputtering and reflection of self-bombardment of tungsten material

Energy Technology Data Exchange (ETDEWEB)

Niu, Guo-jian [University of Science and Technology of China, Hefei (China); Institute of Plasma Physics Chinese Academy of Sciences, Hefei (China); Li, Xiao-chun; Xu, Qian; Yang, Zhong-shi [Institute of Plasma Physics Chinese Academy of Sciences, Hefei (China); Luo, Guang-nan, E-mail: gnluo@ipp.ac.cn [University of Science and Technology of China, Hefei (China); Institute of Plasma Physics Chinese Academy of Sciences, Hefei (China); Hefei Center for Physical Science and Technology, Hefei (China); Hefei Science Center of CAS, Hefei (China)

2015-04-15

In present research, the sputtering and reflection yield of self-bombardment of tungsten are investigated with the aid of molecular dynamics simulations. The source of sputtered and reflected atoms is detected by traced the original locations of sputtered and reflected atoms. Results show that for the reflected atoms no specific region exists which means cluster atoms are randomly reflected. But almost all of sputtered atoms are from a conical region under the landing point of cluster. So we can determine the sputtering yield by study the dimension of the sputtering region. Molecular dynamics shows the depth and radius of the conical are power functions of impacting energy. The effects of cluster size and temperature of target on sputtering and reflection rate are also preformed in present study. Both sputtering and reflection yield are proportion to cluster size in present cluster size, i.e. 66–2647 atoms. Higher target temperature can increase sputtering yield and deduce sputtering threshold energy, but little effect on reflection rate.

Changes in phase composition and stress state of surface layers of VK20 hard alloy after ion bombardment

International Nuclear Information System (INIS)

Platonov, G.L.; Leonov, E.Yu.; Anikin, V.N.; Anikeev, A.I.

1988-01-01

Titanium ion bombardment of the surface of the hard VK20 alloy is studied for its effect on variations in the phase and chemical composition of its surface layers. It is stated that ion treatment results in the appearance of the η-phase of Co 6 W 6 C composition in the surface layer of the VK20 alloy, in the increase of distortions and decrease of coherent scattering blocks of the hard alloy carbide phase. Such a bombardment is found to provoke a transition of the plane-stressed state of the hard alloy surface into the volume-stressed state. It is established that ion treatment does not cause an allotropic transition of the cobalt phase α-modification, formed during grinding of the hard alloy, into the β-modification

Ion bombardment simulation: a review related to fusion radiation damage

International Nuclear Information System (INIS)

Brimhall, J.L.

1975-01-01

Prime emphasis is given to reviewing the ion bombardment data on the refractory metals molybdenum, niobium and vanadium which have been proposed for use in advanced fusion devices. The temperature and dose dependence of the void parameters are correlated among these metals. The effect of helium and hydrogen gas on the void parameters is also included. The similarities and differences of the response of these materials to high dose, high temperature radiation damage are evaluated. Comparisons are made with results obtained from stainless steel and nickel base alloys. The ion bombardment data is then compared and correlated, as far as possible, with existing neutron data on the refractory metals. The theoretically calculated damage state produced by neutrons and ions is also briefly discussed and compared to experimental data wherever possible. The advantages and limitations of ion simulation in relation to fusion radiation damage are finally summarized

Molecular Clusters: Nanoscale Building Blocks for Solid-State Materials.

Science.gov (United States)

Pinkard, Andrew; Champsaur, Anouck M; Roy, Xavier

2018-04-17

The programmed assembly of nanoscale building blocks into multicomponent hierarchical structures is a powerful strategy for the bottom-up construction of functional materials. To develop this concept, our team has explored the use of molecular clusters as superatomic building blocks to fabricate new classes of materials. The library of molecular clusters is rich with exciting properties, including diverse functionalization, redox activity, and magnetic ordering, so the resulting cluster-assembled solids, which we term superatomic crystals (SACs), hold the promise of high tunability, atomic precision, and robust architectures among a diverse range of other material properties. Molecular clusters have only seldom been used as precursors for functional materials. Our team has been at the forefront of new developments in this exciting research area, and this Account focuses on our progress toward designing materials from cluster-based precursors. In particular, this Account discusses (1) the design and synthesis of molecular cluster superatomic building blocks, (2) their self-assembly into SACs, and (3) their resulting collective properties. The set of molecular clusters discussed herein is diverse, with different cluster cores and ligand arrangements to create an impressive array of solids. The cluster cores include octahedral M 6 E 8 and cubane M 4 E 4 (M = metal; E = chalcogen), which are typically passivated by a shell of supporting ligands, a feature upon which we have expanded upon by designing and synthesizing more exotic ligands that can be used to direct solid-state assembly. Building from this library, we have designed whole families of binary SACs where the building blocks are held together through electrostatic, covalent, or van der Waals interactions. Using single-crystal X-ray diffraction (SCXRD) to determine the atomic structure, a remarkable range of compositional variability is accessible. We can also use this technique, in tandem with vibrational

Cleaning of diffusion bonding surface by argon ion bombardment treatment

International Nuclear Information System (INIS)

Wang, Airu; Ohashi, Osamu; Yamaguchi, Norio; Aoki, Masanori; Higashi, Yasuo; Hitomi, Nobuteru

2003-01-01

The specimens of oxygen-free high conductivity copper, SUS304L stainless steel and pure iron were treated by argon ion bombardment and then were bonded by diffusion bonding method. The effects of argon ion bombardment treatment on faying surface morphology, tensile strength of bonding joints and inclusions at the fracture surface were investigated. The results showed that argon ion bombardment treatment was effective to remove the oxide film and contamination at the faying surface and improve the quality of joints. The tensile strength of the bonded joints was improved, and minimum bonding temperature to make the metallic bonding at the interface was lowered by argon ion bombardment treatment. At the joints with argon ion bombardment treatment, ductile fractured surface was seen and the amount of inclusions was obviously decreased

Ion bombardment techniques - recent developments in SIMS

International Nuclear Information System (INIS)

Konarski, P.; Miśnik, M.

2013-01-01

We present a short review of cluster ion bombardment technique recently applied in SIMS. Many advantages of using cluster ion beams are specified over monoatomic ion species. Cluster ions open really new perspectives especially in organic based structures analysis. Nevertheless cluster ions are not the perfect solution and still new ideas of ion erosion in SIMS are needed. Another issue discussed is 'storing matter' technique applied for quantitative analysis in SIMS. Simple idea of sputter deposition of eroded material onto rotating substrate and then analysing the stored material allows to avoid strong matrix effects in SIMS. Presented are the results performed in Tele and Radio Research Institute, Warszawa, Poland. These are the first results of ‘storing matter’ technique performed in one analytical chamber of SIMS instrument. (authors)

Replacement of Fine Aggregate by using Recyclable Materials in Paving Blocks

Science.gov (United States)

Koganti, Shyam Prakash; Hemanthraja, Kommineni; Sajja, Satish

2017-08-01

Cement concrete paving blocks are precast hard products complete out of cement concrete. The product is made in various sizes and shapes like square, round and rectangular blocks of different dimensions with designs for interlocking of adjacent tiles blocks. Several Research Works have been carried out in the past to study the possibility of utilizing waste materials and industrial byproducts in the manufacturing of paver blocks. Various industrial waste materials like quarry dust, glass powder, ceramic dust and coal dust are used as partial replacement of fine aggregate and assessed the strength parameters and compared the profit percentages after replacement with waste materials. Quarry dust can be replaced by 20% and beyond that the difference in strength is not much higher but considering cost we can replace upto 40% so that we can get a profit of almost 10%. Similarly we can replace glass powder and ceramic dust by 20% only beyond that there is decrement in strength and even with 20% replacement we can get 1.34 % and 2.42% of profit. Coal dust is not suitable for alternative material as fine aggregate as it reduces the strength.

Ion-bombardment effects on the fatigue life of stainless steel under simulated fusion first-wall conditions

International Nuclear Information System (INIS)

Kohse, G.E.

1983-02-01

An experiment which uses the MITR-II 5 MW research reactor to simulate several aspects of the anticipated environment of a fusion reactor first wall is described. Pressurized tube specimens are subjected simultaneously to stress and temperature cycling, surface bombardment by energetic helium and lithium ions and bulk irradiation by high-energy neutrons. Analysis of the samples is aimed primarily at determining the behavior of the ion bombarded surface layer, which has a depth of 2.5 μm, with particular reference to possible effects on the fatigue life of the material

Development of Concrete Paving Blocks Prepared from Waste Materials without Portland Cement

Directory of Open Access Journals (Sweden)

Charin NAMARAK

2018-02-01

Full Text Available This experiment used three types of waste materials: calcium carbide residue, fly ash, and recycled concrete aggregate to develop concrete paving blocks. The blocks had calcium carbide residue and fly ash as a binder without ordinary Portland cement (OPC and combined with 100 % of recycled concrete aggregate. The concrete paving blocks were 10 × 10 × 20 cm and were formed using a pressure of 6 or 8 MPa. The binder-to-aggregate ratio was held constant at 1:3 by weight, while the water-to-binder ratios were 0.30, 0.35, and 0.40. The effects of the water-to-binder ratios and fineness of the binder on the compressive strength, flexural strength, abrasion resistance, and water absorption of the concrete paving blocks were determined and compared with those of TIS 827 and ASTM C1319 standards. The results revealed that by applying this procedure, we were able to produce an excellence concrete paving block without using OPC. The compressive strength of the concrete paving blocks made from these waste materials was 41.4 MPa at 28 days and increased to 45.3 MPa at 60 days. Therefore, these waste materials can be used as raw materials to manufacture concrete paving blocks without OPC that meet the requirements of 40 MPa and 35 MPa specified by the TIS 827 and ASTM C1319 standards, respectively.DOI: http://dx.doi.org/10.5755/j01.ms.24.1.17566

Is low-energy-ion bombardment generated X-ray emission a secondary mutational source to ion-beam-induced genetic mutation?

Energy Technology Data Exchange (ETDEWEB)

Thongkumkoon, P. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand); Prakrajang, K. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Faculty of Science, Maejo University, Chiang Mai 50290 (Thailand); Thopan, P.; Yaopromsiri, C. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Suwannakachorn, D. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand); Yu, L.D., E-mail: yuld@fnrf.science.cmu.ac.th [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand)

2013-07-15

Highlights: ► Detected X-ray emission from metal, plastic and biological samples. ► Characteristic X-ray emission was detected from metal but not from non-metals. ► Low-energy ion bombarded bacteria held in different sample holders. ► Bacteria held in metal holder had higher mutation rate than in plastic holder. ► Ion-beam-induced X-ray from biological sample is not a basic mutation source. -- Abstract: Low-energy ion beam biotechnology has achieved tremendous successes in inducing crop mutation and gene transfer. However, mechanisms involved in the related processes are not yet well understood. In ion-beam-induced mutation, ion-bombardment-produced X-ray has been proposed to be one of the secondary mutation sources, but the speculation has not yet been experimentally tested. We carried out this investigation to test whether the low-energy ion-beam-produced X-ray was a source of ion-beam-induced mutation. In the investigation, X-ray emission from 29-keV nitrogen- or argon- ion beam bombarded bacterial Escherichia coli (E. coli) cells held in a metal or plastic sample holder was in situ detected using a highly sensitive X-ray detector. The ion beam bombarded bacterial cells held in different material holders were observed for mutation induction. The results led to a conclusion that secondary X-ray emitted from ion-beam-bombarded biological living materials themselves was not a, or at least a negligible, mutational source, but the ion-beam-induced X-ray emission from the metal that made the sample holder could be a source of mutation.

Is low-energy-ion bombardment generated X-ray emission a secondary mutational source to ion-beam-induced genetic mutation?

International Nuclear Information System (INIS)

Thongkumkoon, P.; Prakrajang, K.; Thopan, P.; Yaopromsiri, C.; Suwannakachorn, D.; Yu, L.D.

2013-01-01

Highlights: ► Detected X-ray emission from metal, plastic and biological samples. ► Characteristic X-ray emission was detected from metal but not from non-metals. ► Low-energy ion bombarded bacteria held in different sample holders. ► Bacteria held in metal holder had higher mutation rate than in plastic holder. ► Ion-beam-induced X-ray from biological sample is not a basic mutation source. -- Abstract: Low-energy ion beam biotechnology has achieved tremendous successes in inducing crop mutation and gene transfer. However, mechanisms involved in the related processes are not yet well understood. In ion-beam-induced mutation, ion-bombardment-produced X-ray has been proposed to be one of the secondary mutation sources, but the speculation has not yet been experimentally tested. We carried out this investigation to test whether the low-energy ion-beam-produced X-ray was a source of ion-beam-induced mutation. In the investigation, X-ray emission from 29-keV nitrogen- or argon- ion beam bombarded bacterial Escherichia coli (E. coli) cells held in a metal or plastic sample holder was in situ detected using a highly sensitive X-ray detector. The ion beam bombarded bacterial cells held in different material holders were observed for mutation induction. The results led to a conclusion that secondary X-ray emitted from ion-beam-bombarded biological living materials themselves was not a, or at least a negligible, mutational source, but the ion-beam-induced X-ray emission from the metal that made the sample holder could be a source of mutation

Modification of thin film properties by ion bombardment during deposition

International Nuclear Information System (INIS)

Harper, J.M.E.; Cuomo, J.J.; Gambino, R.J.; Kaufman, H.R.

1984-01-01

Deposition methods involving ion bombardment are described, and the basic processes with which film properties are modified by ion bombardment are summarized. Examples of thin film property modification by ion bombardment during deposition, including effects which are primarily compositional as well as those which are primarily structural are presented. The examples demonstrate the usefulness of ion beam techniques in identifying and controlling the fundamental deposition parameters. 68 refs.; 15 figs.; 1 table

Efficient and rapid C. elegans transgenesis by bombardment and hygromycin B selection.

Directory of Open Access Journals (Sweden)

Inja Radman

Full Text Available We report a simple, cost-effective, scalable and efficient method for creating transgenic Caenorhabditis elegans that requires minimal hands-on time. The method combines biolistic bombardment with selection for transgenics that bear a hygromycin B resistance gene on agar plates supplemented with hygromycin B, taking advantage of our observation that hygromycin B is sufficient to kill wild-type C. elegans at very low concentrations. Crucially, the method provides substantial improvements in the success of bombardments for isolating transmitting strains, the isolation of multiple independent strains, and the isolation of integrated strains: 100% of bombardments in a large data set yielded transgenics; 10 or more independent strains were isolated from 84% of bombardments, and up to 28 independent strains were isolated from a single bombardment; 82% of bombardments yielded stably transmitting integrated lines with most yielding multiple integrated lines. We anticipate that the selection will be widely adopted for C. elegans transgenesis via bombardment, and that hygromycin B resistance will be adopted as a marker in other approaches for manipulating, introducing or deleting DNA in C. elegans.

Spatial variation in void volume during charged particle bombardment: the effects of injected interstitials

International Nuclear Information System (INIS)

Lee, E.H.; Mansur, L.K.; Yoo, M.H.

1979-01-01

Experimental observations of the void volume at several depths along the range of 4 MeV Ni ions in 316 stainless steel are reported. The specimens were first preconditioned by neutron irradiation at temperatures of 450 and 584 0 C to fluences of approximately 8 x 10 26 n/m -2 . The void volume after ion bombardment to 60 dpa at the peak damage depth is significantly lower at the peak damage depth than in the region between that and the free surface. The ratio of the step height to void volume at the depth of peak energy deposition between regions masked from and exposed to the beam is strongly dependent on bombardment temperature. The reduction of void volume near the peak damage depth is larger for the 584 0 C than for the 450 0 C preconditioned material. These observations are consistent with recent theoretical results which account for the injection of the bombarding ions as self-interstitials. The theory necessary to understand the effect is developed

Exfoliation on stainless steel and inconel produced by 0.8-4 MeV helium ion bombardment

International Nuclear Information System (INIS)

Paszti, F.; Mezey, G.; Pogany, L.; Fried, M.; Manuaba, A.; Kotai, E.; Lohner, T.; Pocs, L.

1982-11-01

Trying to outline the energy dependence of surface deformations such as exfoliation and flaking on candidate CTR first-wall materials, stainless steel and two types of inconels were bombarded by 0.8, 1 and 4 MeV helium ions. All the bombarded spots could be characterized by by large exfoliations covering almost the total implanted area. No spontaneous rupture was observed except on one type of inconel where flaking took place right after reaching the critical dose. After mechanical opening of the formations, similar inner morphology was found as in our previous studies on gold. (author)

Catalytic oxidation of silicon by cesium ion bombardment

International Nuclear Information System (INIS)

Souzis, A.E.; Huang, H.; Carr, W.E.; Seidl, M.

1991-01-01

Results for room-temperature oxidation of silicon using cesium ion bombardment and low oxygen exposure are presented. Bombardment with cesium ions is shown to allow oxidation at O 2 pressures orders of magnitude smaller than with noble gas ion bombardment. Oxide layers of up to 30 A in thickness are grown with beam energies ranging from 20--2000 eV, O 2 pressures from 10 -9 to 10 -6 Torr, and total O 2 exposures of 10 0 to 10 4 L. Results are shown to be consistent with models indicating that initial oxidation of silicon is via dissociative chemisorption of O 2 , and that the low work function of the cesium- and oxygen-coated silicon plays the primary role in promoting the oxidation process

Mechanism of conductivity type conversion in p-Hg1-xCdxTe crystals under low energy ion bombardment

International Nuclear Information System (INIS)

Bogoboyashchij, V.V.; Izhnin, I.I.

2000-01-01

Conditions giving rise to accelerated diffusion of Hg under bombardment of p-Hg 1-x Cd x Te by low-energy particles are analyzed and probable mechanisms of the phenomenon are suggested, permitting qualitative and quantitative agreement with experimental data. Analysis indicates that basic regularities of p-n-conversion during Hg 0.8 Cd 0.2 Te crystal bombardment by neutralized ions can be easily explained in the framework of traditional notions of mercury chemical diffusion in this material. The regularities stem from specific features of defect formation in Hg 0.8 Cd 0.2 Te, on the one hand, and from a high concentration of intrinsic electrons and holes, screening effectively the defective layer electric field, on the other hand. The high rate of conversion during ion bombardment compared with the rate of conversion during annealing in mercury vapors can be explained by the fact that a great number of nonequilibrium interstitial atoms of mercury, by far exceeding the value during thermal annealing, is crated near the surface of the crystal bombarded [ru

Adhesion of evaporated titanium films to ion-bombarded polyethylene

International Nuclear Information System (INIS)

Bodoe, P.; Sundgren, J.

1986-01-01

Ti films were deposited onto high-density polyethylene (HDPE) samples by electron-beam evaporation. Prior to film deposition the samples were in situ pretreated by Ar ion bombardment using a sputter ion gun. The adhesion of the films, determined as the pull strength required for film failure, was measured as a function of ion dose. HDPE substrates processed at two different temperatures were examined. The adhesion of the Ti films to HDPE samples processed at roughly-equal150 0 C increased with the ion dose to a steady-state value corresponding to the cohesive strength of the HDPE substrate. The adhesion to the samples processed at roughly-equal200 0 C increased to a maximum and then decreased for further ion bombardment to a level of the same order as that for films deposited onto as-prepared samples. The effects of the ion bombardment upon the HDPE surface chemistry were examined by means of x-ray photoelectron spectroscopy (XPS). The ion bombardment resulted in dehydrogenation and cross linking of the surface region and for prolonged ion bombardment, a graphitelike surface was obtained. The film/substrate interface as well as the initial Ti film growth were examined by XPS analysis. A chemical interaction which resulted in Ti--C bonds was observed at the interface. The Ti film growth followed a pronounced three-dimensional growth mode on as-prepared surfaces whereas the ion bombardment resulted in a change toward a more two-dimensional growth mode. The difference in adhesion behavior for the two types of HDPE substrates was found to be due to a difference in the amounts of low molecular weight products present within the substrates

Computer simulations of material ejection during C{sub 60} and Ar{sub m} bombardment of octane and β-carotene

Energy Technology Data Exchange (ETDEWEB)

Palka, G.; Kanski, M.; Maciazek, D. [Smoluchowski Institute of Physics, Jagiellonian University, ul. Reymonta 4, 30-059 Krakow (Poland); Garrison, B.J. [Department of Chemistry, 104 Chemistry Building, Penn State University, University Park, PA 16802 (United States); Postawa, Z., E-mail: zbigniew.postawa@uj.edu.pl [Smoluchowski Institute of Physics, Jagiellonian University, ul. Reymonta 4, 30-059 Krakow (Poland)

2015-06-01

Molecular dynamics (MD) computer simulations are used to investigate material ejection and fragment formation during keV C{sub 60} and Ar{sub m} (m = 60, 101, 205, 366, 872 and 2953) bombardment of organic solids composed from octane and β-carotene molecules at 0° and 45° impact angle. Both systems are found to sputter efficiently. For the octane system, material removal occurs predominantly by ejection of intact molecules, while fragment emission is a significant ejection channel for β-carotene. A difference in the molecular dimensions is proposed to explain this observation. It has been shown that the dependence of the sputtering yield Y on the primary kinetic energy E and the cluster size n can be expressed in a simplified form if represented in reduced units. A linear and nonlinear dependence of the Y/n on the E/n are identified and the position of the transition point from the linear to nonlinear regions depends on the size of the cluster projectile. The impact angle has a minor influence on the shape of the simplified representation.

Advances in fast-atom-bombardment mass spectroscopy

International Nuclear Information System (INIS)

Hemling, M.E.

1986-01-01

A comparison of fast atom bombardment and field desorption mass spectrometry was made to determine relative sensitivity and applicability. A series of glycosphingolipids and a series of protected oligonucleotides of known structure were analyzed to ascertain the potential utility of fast atom bombardment mass spectrometry in the structural elucidation of novel compounds in these classes. Negative ion mass markers were also developed. Fast atom bombardment was found to be one-to-two orders of magnitude more sensitive than field desorption based on the analysis of a limited number of compounds from several classes. Superior sensitivity was not universal and field desorption was clearly better in certain cases. In the negative ion mode in particular, fast atom bombardment was found to be a useful tool for the determination of the primary structure of glycosphingolipids and oligonucleotides. Carbohydrate sequence and branching information, and a fatty acid and lipid base composition were readily obtained from the mass spectra of glycosphingolipids while bidirectional nucleotide sequence, nucleotide base, and protecting group assignments were obtained for oligonucleotides. Based on this knowledge, a tentative structure of a human peripheral nervous system glycosphingolipid implicated in certain cases of disorders such as amyotrophic lateral sclerosis, Lou Gehrig's Disease, was proposed. Suitable negative ion mass markers were found in dispersions of poly(ethylene) and poly(propylene)glycols in a triethylenetetramine matrix, a matrix which also proved useful in the analysis of glycosphingolipids. These polyglycol dispersions provided ions for calibration to 2300 daltons

Experimental and theoretical studies of bombardment induced surface morphology changes

International Nuclear Information System (INIS)

Carter, G.; Nobes, M.J.; Williams, J.S.

1980-01-01

In this review results of experimental and theoretical studies of solid surface morphology changes due to ion bombardment are discussed. An attempt is undertaken to classify the observed specific features of a structure, generated by ion bombardment [ru

Direct and Recoil-Induced Electron Emission from Ion-Bombarded Solids

DEFF Research Database (Denmark)

Holmen, G.; Svensson, B.; Schou, Jørgen

1979-01-01

The kinetic emission of secondary electrons from ion-bombarded solid surfaces is split into two contributions, a direct one caused by ionizing collisions between the bombarding ion and target atoms, and an indirect one originating from ionizing collisions undergone by recoil atoms with other target...... atoms. The direct contribution, which has been treated by several authors in previous studies, shows a behavior that is determined primarily by the electronic stopping power of the bombarding ion, while the indirect contribution is nonproportionally related to the nuclear stopping power. This latter...

Destruction of C60 films by boron ion bombardment

International Nuclear Information System (INIS)

Ren Zhongmin; Du Yuancheng; Ying Zhifeng; Xiong Xiaxing; Li Fuming

1995-01-01

C 60 films are bombarded by 100 keV boron ion beams at doses ranging from 3x10 14 to 1x10 16 /cm 2 . The bombarded films are analyzed using Fourier transform infrared spectroscopy (FTIR), Raman spectra and X-ray diffraction (XRD) measurements. Most C 60 soccer-balls in the implanted region in the films are found to be broken at a dose over 1x10 15 /cm 2 , while at a dose less than 6x10 14 /cm 2 a few C 60 molecules remain undestroyed and maintain some crystal structure. The results of the analyses suggest a complete disintegration of a C 60 molecule under B + bombardment. ((orig.))

Very low-energy and low-fluence ion beam bombardment of naked plasmid DNA

International Nuclear Information System (INIS)

Norarat, R.; Semsang, N.; Anuntalabhochai, S.; Yu, L.D.

2009-01-01

Ion beam bombardment of biological organisms has been recently applied to mutation breeding of both agricultural and horticultural plants. In order to explore relevant mechanisms, this study employed low-energy ion beams to bombard naked plasmid DNA. The study aimed at simulation of the final stage of the process of the ion beam bombardment of real cells to check whether and how very low-energy and low-fluence of ions can induce mutation. Argon and nitrogen ions at 5 keV and 2.5 keV respectively bombarded naked plasmid DNA pGFP to very low-fluences, an order of 10 13 ions/cm 2 . Subsequently, DNA states were analyzed using electrophoresis. Results provided evidences that the very low-energy and low-fluence ion bombardment indeed altered the DNA structure from supercoil to short linear fragments through multiple double strand breaks and thus induced mutation, which was confirmed by transfer of the bombarded DNA into bacteria Escherichia coli and subsequent expression of the marker gene.

Characterization techniques for ion bombarded insulators

International Nuclear Information System (INIS)

Borders, J.A.

1987-01-01

The chapter gives a comprehensive review of the experimental methods for the analysis of ion-bombarded insulators including optical and structural methods, resonance, energetic ion methods, and surface techniques. 48 refs.; 34 figs

Ion bombardment modification of surfaces

International Nuclear Information System (INIS)

Auciello, O.

1984-01-01

Ion bombardment-induced modification of surfaces may be considered one of the significant scientific and technological developments of the last two decades. The understanding acquired concerning the underlying mechanisms of several phenomena occurring during ion-surface interactions has led to applications within different modern technologies. These include microelectronics, surface acoustical and optical technologies, solar energy conversion, thin film technology, ion implantation metallurgy, nuclear track technology, thermonuclear fusion, vacuum technology, cold welding technology, biomedicine (implantology). It has become clear that information on many relevant advances, regarding ion bombardment modification of surfaces is dispersed among journals involving fields sometimes not clearly related. This may result, in some cases, in a loss of the type of interdisciplinary exchange of ideas, which has proved to be so fruitful for the advancement of science and technology. This book has been planned in an attempt to collect at least some of today's relevant information about the experimental and theoretical knowledge related to surface modification and its application to technology. (Auth.)

Induction of antioxidant enzyme activity and lipid peroxidation level in ion-beam-bombarded rice seeds

Energy Technology Data Exchange (ETDEWEB)

Semsang, Nuananong, E-mail: nsemsang@gmail.com [Molecular Biology Laboratory, Department of Biology, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Yu, LiangDeng [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand)

2013-07-15

Highlights: ► Ion beam bombarded rice seeds in vacuum. ► Studied seed survival from the ion bombardment. ► Determined various antioxidant enzyme activities and lipid peroxidation level. ► Discussed vacuum, ion species and ion energy effects. ► Attributed the changes to free radical formation due to ion bombardment. -- Abstract: Low-energy ion beam bombardment has been used to mutate a wide variety of plant species. To explore the indirect effects of low-energy ion beam on biological damage due to the free radical production in plant cells, the increase in antioxidant enzyme activities and lipid peroxidation level was investigated in ion-bombarded rice seeds. Local rice seeds were bombarded with nitrogen or argon ion beams at energies of 29–60 keV and ion fluences of 1 × 10{sup 16} ions cm{sup −2}. The activities of the antioxidant enzymes; superoxide dismutase (SOD), catalase (CAT), ascorbate peroxidase (APX), dehydroascorbate reductase (DHAR), glutathione reductase (GR), glutathione S-transferase (GST) and lipid peroxidation level were assayed in the germinated rice seeds after ion bombardment. The results showed most of the enzyme activities and lipid peroxidation levels in both the argon and nitrogen bombarded samples were higher than those in the natural control. N-ion bombardment could induce higher levels of antioxidant enzyme activities in the rice samples than the Ar-ion bombardment. Additional effects due to the vacuum condition were found to affect activities of some antioxidant enzymes and lipid peroxidation level. This study demonstrates that ion beam bombardment and vacuum condition could induce the antioxidant enzyme activity and lipid peroxidation level which might be due to free radical production in the bombarded rice seeds.

Topography of InP surface bombarded by O2+ ion beam

International Nuclear Information System (INIS)

Sun Zhaoqi

1997-01-01

The topography of InP surface bombarded by O 2 + ion beam was investigated. Rippled topographies were observed for bombarded samples, and the data show that the ripple formation starts from a sputtering depth of about 0.4 μm. The wavelength and the disorder of the ripples both increase as the sputtering depth increases. The wavelength of the ripples appears to be sputtering depth dependent rather than sputtering rate dependent. It is confirmed that the ion-beam-induced surface rippling can be effectively suppressed by sample rotation during bombardment

Ion bombardment and disorder in amorphous silicon

International Nuclear Information System (INIS)

Sidhu, L.S.; Gaspari, F.; Zukotynski, S.

1997-01-01

The effect of ion bombardment during growth on the structural and optical properties of amorphous silicon are presented. Two series of films were deposited under electrically grounded and positively biased substrate conditions. The biased samples displayed lower growth rates and increased hydrogen content relative to grounded counterparts. The film structure was examined using Raman spectroscopy. The transverse optic like phonon band position was used as a parameter to characterize network order. Biased samples displayed an increased order of the amorphous network relative to grounded samples. Furthermore, biased samples exhibited a larger optical gap. These results are correlated and attributed to reduced ion bombardment effects

InN: Fermi level stabilization by low-energy ion bombardment

International Nuclear Information System (INIS)

Piper, L.F.J.; Veal, T.D.; McConville, C.F.; Lu, H.; Schaff, W.J.

2006-01-01

The near-surface electronic properties of InN have been investigated with high-resolution electron-energy loss spectroscopy. Low-energy (∝400 eV) nitrogen ion bombardment followed by low temperature annealing (<300 C) was found to dramatically increase the n-type conductivity of InN, close to the surface. This is explained in terms of the formation of amphoteric defects from the ion bombardment and annealing combined with the band structure of InN. Low-energy ion bombardment and annealing is shown to result in a damage-induced, donor-like defect-profile instead of the expected electron accumulation for InN. (copyright 2006 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Cesium ion bombardment of metal surfaces

International Nuclear Information System (INIS)

Tompa, G.S.

1986-01-01

The steady state cesium coverage due to cesium ion bombardment of molybdenum and tungsten was studied for the incident energy range below 500 eV. When a sample is exposed to a positive ion beam, the work function decreases until steady state is reached with a total dose of less than ≅10 16 ions/cm 2 , for both tungsten and molybdenum. A steady state minimum work function surface is produced at an incident energy of ≅100 eV for molybdenum and at an incident energy of ≅45 eV for tungsten. Increasing the incident energy results in an increase in the work function corresponding to a decrease in the surface coverage of cesium. At incident energies less than that giving the minimum work function, the work function approaches that of cesium metal. At a given bombarding energy the cesium coverage of tungsten is uniformly less than that of molybdenum. Effects of hydrogen gas coadsorption were also examined. Hydrogen coadsorption does not have a large effect on the steady state work functions. The largest shifts in the work function due to the coadsorption of hydrogen occur on the samples when there is no cesium present. A theory describing the steady-state coverage was developed is used to make predictions for other materials. A simple sticking and sputtering relationship, not including implantation, cannot account for the steady state coverage. At low concentrations, cesium coverage of a target is proportional to the ratio of (1 - β)/γ where β is the reflection coefficient and γ is the sputter yield. High coverages are produced on molybdenum due to implantation and low backscattering, because molybdenum is lighter than cesium. For tungsten the high backscattering and low implantation result in low coverages

Induction of antioxidant enzyme activity and lipid peroxidation level in ion-beam-bombarded rice seeds

Science.gov (United States)

Semsang, Nuananong; Yu, LiangDeng

2013-07-01

Low-energy ion beam bombardment has been used to mutate a wide variety of plant species. To explore the indirect effects of low-energy ion beam on biological damage due to the free radical production in plant cells, the increase in antioxidant enzyme activities and lipid peroxidation level was investigated in ion-bombarded rice seeds. Local rice seeds were bombarded with nitrogen or argon ion beams at energies of 29-60 keV and ion fluences of 1 × 1016 ions cm-2. The activities of the antioxidant enzymes; superoxide dismutase (SOD), catalase (CAT), ascorbate peroxidase (APX), dehydroascorbate reductase (DHAR), glutathione reductase (GR), glutathione S-transferase (GST) and lipid peroxidation level were assayed in the germinated rice seeds after ion bombardment. The results showed most of the enzyme activities and lipid peroxidation levels in both the argon and nitrogen bombarded samples were higher than those in the natural control. N-ion bombardment could induce higher levels of antioxidant enzyme activities in the rice samples than the Ar-ion bombardment. Additional effects due to the vacuum condition were found to affect activities of some antioxidant enzymes and lipid peroxidation level. This study demonstrates that ion beam bombardment and vacuum condition could induce the antioxidant enzyme activity and lipid peroxidation level which might be due to free radical production in the bombarded rice seeds.

FTIR and Vis-FUV real time spectroscopic ellipsometry studies of polymer surface modifications during ion beam bombardment

Science.gov (United States)

Laskarakis, A.; Gravalidis, C.; Logothetidis, S.

2004-02-01

The continuously increasing application of polymeric materials in many scientific and technological fields has motivated an extensive use of polymer surface treatments, which modify the physical and chemical properties of polymer surfaces leading to surface activation and promotion of the surface adhesion. Fourier transform IR spectroscopic ellipsometry (FTIRSE) and phase modulated ellipsometry (PME) in the IR and Vis-FUV spectral regions respectively have been employed for in situ and real time monitoring of the structural changes on the polymer surface obtained by Ar + ion bombardment. The polymers were industrially supplied polyethylene terephthalate (PET) and polyethylene naphthalate (PEN) membranes. The Ar + ion bombardment has found to change the chemical bonding of the films and especially the amount of the CO, C-C and CC groups. The detailed study of the FTIRSE spectra reveals important information about the effect of the Ar + ion bombardment on each of the above bonding groups. Also, the modification of the characteristic features, attributed to electronic transitions in specific bonds of PET and PEN macromolecules, has been studied using PME.

FTIR and Vis-FUV real time spectroscopic ellipsometry studies of polymer surface modifications during ion beam bombardment

International Nuclear Information System (INIS)

Laskarakis, A.; Gravalidis, C.; Logothetidis, S.

2004-01-01

The continuously increasing application of polymeric materials in many scientific and technological fields has motivated an extensive use of polymer surface treatments, which modify the physical and chemical properties of polymer surfaces leading to surface activation and promotion of the surface adhesion. Fourier transform IR spectroscopic ellipsometry (FTIRSE) and phase modulated ellipsometry (PME) in the IR and Vis-FUV spectral regions respectively have been employed for in situ and real time monitoring of the structural changes on the polymer surface obtained by Ar + ion bombardment. The polymers were industrially supplied polyethylene terephthalate (PET) and polyethylene naphthalate (PEN) membranes. The Ar + ion bombardment has found to change the chemical bonding of the films and especially the amount of the C-O, C-C and C-C groups. The detailed study of the FTIRSE spectra reveals important information about the effect of the Ar + ion bombardment on each of the above bonding groups. Also, the modification of the characteristic features, attributed to electronic transitions in specific bonds of PET and PEN macromolecules, has been studied using PME

Ion Back-Bombardment of GaAs Photocathodes Inside DC High Voltage Electron Guns

CERN Document Server

Grames, Joseph M; Brittian, Joshua; Charles, Daniel; Clark, Jim; Hansknecht, John; Lynn Stutzman, Marcy; Poelker, Matthew; Surles-Law, Kenneth E

2005-01-01

The primary limitation for sustained high quantum efficiency operation of GaAs photocathodes inside DC high voltage electron guns is ion back-bombardment of the photocathode. This process results from ionization of residual gas within the cathode/anode gap by the extracted electron beam, which is subsequently accelerated backwards to the photocathode. The damage mechanism is believed to be either destruction of the negative electron affinity condition at the surface of the photocathode or damage to the crystal structure by implantation of the bombarding ions. This work characterizes ion formation within the anode/cathode gap for gas species typical of UHV vacuum chambers (i.e., hydrogen, carbon monoxide and methane). Calculations and simulations are performed to determine the ion trajectories and stopping distance within the photocathode material. The results of the simulations are compared with test results obtained using a 100 keV DC high voltage GaAs photoemission gun and beamline at currents up to 10 mA D...

Magnetoresistance and ion bombardment induced magnetic patterning

International Nuclear Information System (INIS)

Hoeink, V.

2008-01-01

In this thesis the combination of the magnetic patterning of the unidirectional anisotropy and the tunnel magnetoresistance effect is investigated. In my diploma thesis, it has been shown that it is in principle possible to use the magnetic patterning by ion bombardment to magnetically structure the pinned layer in magnetic tunnel junctions (MTJs) with alumina barrier. Furthermore, it has been shown that the side effects which have been observed after this treatment can be at least reduced by an additional heating step. Starting from this point, the applicability of ion bombardment induced magnetic patterning (IBMP) in general and the combination of IBMP and MTJs in particular is investigated and new applications are developed. (orig.)

The timeline of the lunar bombardment: Revisited

Science.gov (United States)

Morbidelli, A.; Nesvorny, D.; Laurenz, V.; Marchi, S.; Rubie, D. C.; Elkins-Tanton, L.; Wieczorek, M.; Jacobson, S.

2018-05-01

The timeline of the lunar bombardment in the first Gy of Solar System history remains unclear. Basin-forming impacts (e.g. Imbrium, Orientale), occurred 3.9-3.7 Gy ago, i.e. 600-800 My after the formation of the Moon itself. Many other basins formed before Imbrium, but their exact ages are not precisely known. There is an intense debate between two possible interpretations of the data: in the cataclysm scenario there was a surge in the impact rate approximately at the time of Imbrium formation, while in the accretion tail scenario the lunar bombardment declined since the era of planet formation and the latest basins formed in its tail-end. Here, we revisit the work of Morbidelli et al. (2012) that examined which scenario could be compatible with both the lunar crater record in the 3-4 Gy period and the abundance of highly siderophile elements (HSE) in the lunar mantle. We use updated numerical simulations of the fluxes of asteroids, comets and planetesimals leftover from the planet-formation process. Under the traditional assumption that the HSEs track the total amount of material accreted by the Moon since its formation, we conclude that only the cataclysm scenario can explain the data. The cataclysm should have started ∼ 3.95 Gy ago. However we also consider the possibility that HSEs are sequestered from the mantle of a planet during magma ocean crystallization, due to iron sulfide exsolution (O'Neil, 1991; Rubie et al., 2016). We show that this is likely true also for the Moon, if mantle overturn is taken into account. Based on the hypothesis that the lunar magma ocean crystallized about 100-150 My after Moon formation (Elkins-Tanton et al., 2011), and therefore that HSEs accumulated in the lunar mantle only after this timespan, we show that the bombardment in the 3-4 Gy period can be explained in the accretion tail scenario. This hypothesis would also explain why the Moon appears so depleted in HSEs relative to the Earth. We also extend our analysis of the

Evolution of atomic-scale surface structures during ion bombardment: A fractal simulation

International Nuclear Information System (INIS)

Shaheen, M.A.; Ruzic, D.N.

1993-01-01

Surfaces of interest in microelectronics have been shown to exhibit fractal topographies on the atomic scale. A model utilizing self-similar fractals to simulate surface roughness has been added to the ion bombardment code TRIM. The model has successfully predicted experimental sputtering yields of low energy (less then 1000 eV) Ar on Si and D on C using experimentally determined fractal dimensions. Under ion bombardment the fractal surface structures evolve as the atoms in the collision cascade are displaced or sputtered. These atoms have been tracked and the evolution of the surface in steps of one monolayer of flux has been determined. The Ar--Si system has been studied for incidence energies of 100 and 500 eV, and incidence angles of 0 degree, 30 degree, and 60 degree. As expected, normally incident ion bombardment tends to reduce the roughness of the surface, whereas large angle ion bombardment increases the degree of surface roughness. Of particular interest though, the surfaces are still locally self-similar fractals after ion bombardment and a steady state fractal dimension is reached, except at large angles of incidence

Hydrogen pumping and release by graphite under high flux plasma bombardment

International Nuclear Information System (INIS)

Hirooka, Y.; Leung, W.K.; Conn, R.W.; Goebel, D.M.; Labombard, B.; Nygren, R.; Wilson, K.L.

1988-01-01

Inert gas (helium or argon) plasma bombardment has been found to increase the surface gas adsorptivity of isotropic graphite (POCO-graphite), which can then getter residual gases in a high vacuum system. The inert gas plasma bombardment was carried out at a flux ∼ 1 x 10 18 ions s -1 cm -2 to a fluence of the order of 10 21 ions/cm 2 and at temperatures around 800 degree C. The plasma bombarding energy was varied between 100 and 200 eV. The gettering speed of the activated graphite surface is estimated to be as large as 25 liters s -1 cm -2 at total pressures between 10 -6 and 10 -7 torr. The gettering capacity estimated is 0.025 torr-liter/cm 2 at room temperature. The gettering capability of graphite can be easily recovered by repeating inert gas plasma bombardment. The activated graphite surface exhibits a smooth, sponge-like morphology with significantly increased pore openings, which correlates with the observed increase in the surface gas adsorptivity. The activated graphite surface has been observed to pump hydrogen plasma particles as well. From calibrated H-alpha measurements, the dynamic hydrogen retention capacity is evaluated to be as large as 2 x 10 18 H/cm 2 at temperatures below 100 degree C and at a plasma bombarding energy of 300 eV

Technological characteristics of compressed earth blocks for its use as a building material

Science.gov (United States)

Gomez-Villalba, Luz Stella; Camacho-Perez, Nancy; Alvarez de Buergo, Monica; Becerra-Becerra, Javier; Esmeralda Corredor-Pulido, Dery; Fort, Rafael

2013-04-01

We present here an innovative building technique, which uses ecological, inexpensive and environmentally friendly materials. These compressed earth blocks seem to be very good for building purposes and that is why we have characterized three types of compressed earth blocks (CEB, named by their color as yellow, grey and red) mineralogically by means of X ray diffraction XRD and scanning electron microscopy SEM (both blocks and raw materials), petrographically by polarizing optical light microscopy POLM, and SEM, and, mainly, petrophysically: their hydric, physical and physico-mechanical properties by means of determining their capillary water absorption, porosity (open or accessible to water, pore size distribution and micro/macroporosity), and densities, color and ultrasound velocity (together with anisotropy). The particularities of these analyzed materials show that some varieties are more durable than others, and that all of them can be used as building materials with some restrictions related to their appropriate placing in the structures and the exposure to water. Acknowledgements: This work is supported by the GEOMATERIALES (S2009/MAT-1629) and CONSOLIDER-TCP (CSD2007-0058) programmes. Thanks also to the UCM (Complutense University of Madrid) Research Group "Alteración y conservación de los materiales pétreos del patrimonio" / Alteration and conservation of heritage stone materials (ref. 921349).

Impact and spreading behavior of cluster atoms bombarding substrates

Energy Technology Data Exchange (ETDEWEB)

Fang, Te-Hua, E-mail: fang.tehua@msa.hinet.net [Institute of Mechanical and Electromechanical Engineering, National Formosa University, Yunlin 632, Taiwan (China); Kang, Shao-Hui; Liao, Jia-Hung [Institute of Mechanical and Electromechanical Engineering, National Formosa University, Yunlin 632, Taiwan (China)

2009-12-15

The purpose of this study is to investigate the behavior of copper cluster atoms bombarding a substrate using molecule dynamics based on tight-binding second moment approximation (TB-SMA) potential. The simulated results show that a crater on the substrate surface was created by the impact of the clusters. The variations of kinetic energy of cluster bombardments can be divided into three stages. At the initial impact level, the kinetic energies of the clusters and the substrate were constant. Then, the system went into a sluggish stage of energy variation, in which the kinetic energy of the clusters reduced. In the final stage, the kinetic energy of the system became stable. The high slip vector region around the crater had a disorder damage zone. The symmetry-like cross-slip occurred beneath the top layer of the substrate along the <1 1 0> orientations. The spreading index, temperature, and potential functions that affect the bombardments are also discussed.

Impact and spreading behavior of cluster atoms bombarding substrates

International Nuclear Information System (INIS)

Fang, Te-Hua; Kang, Shao-Hui; Liao, Jia-Hung

2009-01-01

The purpose of this study is to investigate the behavior of copper cluster atoms bombarding a substrate using molecule dynamics based on tight-binding second moment approximation (TB-SMA) potential. The simulated results show that a crater on the substrate surface was created by the impact of the clusters. The variations of kinetic energy of cluster bombardments can be divided into three stages. At the initial impact level, the kinetic energies of the clusters and the substrate were constant. Then, the system went into a sluggish stage of energy variation, in which the kinetic energy of the clusters reduced. In the final stage, the kinetic energy of the system became stable. The high slip vector region around the crater had a disorder damage zone. The symmetry-like cross-slip occurred beneath the top layer of the substrate along the orientations. The spreading index, temperature, and potential functions that affect the bombardments are also discussed.

Self-Assembled Gold Nano-Ripple Formation by Gas Cluster Ion Beam Bombardment.

Science.gov (United States)

Tilakaratne, Buddhi P; Chen, Quark Y; Chu, Wei-Kan

2017-09-08

In this study, we used a 30 keV argon cluster ion beam bombardment to investigate the dynamic processes during nano-ripple formation on gold surfaces. Atomic force microscope analysis shows that the gold surface has maximum roughness at an incident angle of 60° from the surface normal; moreover, at this angle, and for an applied fluence of 3 × 10 16 clusters/cm², the aspect ratio of the nano-ripple pattern is in the range of ~50%. Rutherford backscattering spectrometry analysis reveals a formation of a surface gradient due to prolonged gas cluster ion bombardment, although the surface roughness remains consistent throughout the bombarded surface area. As a result, significant mass redistribution is triggered by gas cluster ion beam bombardment at room temperature. Where mass redistribution is responsible for nano-ripple formation, the surface erosion process refines the formed nano-ripple structures.

Ion bombardment induced ripple topography on amorphous solids

International Nuclear Information System (INIS)

Carter, G.; Nobes, M.J.; Paton, F.; Williams, J.S.

1977-01-01

Earlier studies of the ion bombardment induced ripple morphology on the surfaces of amorphous solids when compared with geomorphological effects are shown to possess many similar features. The present study, with 40 keV Ar + ion bombarded Si suggests that analogies are incomplete, however, and that greater similarities with the process of macroscopic sandblasting (corrosion) exist. It is shown that the genesis of wave like structures on Si is from isolated features, which have the appearance of ripple trains, which are faceted. It is suggested that these features result from particle flux enhancement processes near surface dimples generated by stress induced surface lifting. (author)

Excited-atom production by electron and ion bombardment of alkali halides

International Nuclear Information System (INIS)

Walkup, R.E.; Avouris, P.; Ghosh, A.P.

1987-01-01

We present experimental results on the production of excited atoms by electron and ion bombardment of alkali halides. For the case of electron bombardment, Doppler shift measurements show that the electronically excited atoms have a thermal velocity distribution in equilibrium with the surface temperature. Measurements of the absolute yield of excited atoms, the distribution of population among the excited states, and the systematic dependence on incident electron current and sample temperature support a model in which the excited atoms are produced by gas-phase collisions between desorbed ground-state atoms and secondary electrons. In contrast, for the case of ion bombardment, the excited atoms are directly sputtered from the surface, with velocity distributions characteristic of a collision cascade, and with typical energies of --10 eV

Compositional disordering of GaAs/AlGaAs multiple quantum wells using ion bombardment at elevated temperatures

International Nuclear Information System (INIS)

Anderson, K.K.; Donnelly, J.P.; Wang, C.A.; Woodhouse, J.D.; Haus, H.A.

1988-01-01

A new method has been developed for compositional mixing of heterostructures by ion bombardment at elevated temperatures. Complete mixing of a 1-μm-thick GaAs/AlGaAs 40-period multiple quantum well layer has been achieved by bombardment with 380 keV Ne + ions for 1 h with the sample at 700 0 C. This temperature is much lower than the annealing temperatures used in other vacancy-enhanced disordering techniques, and even lower temperatures and shorter durations should be possible. Compositional disordering is verified by sputter-profile Auger electron spectroscopy and transmission electron microscopy. Complete mixing is also demonstrated by optical transmission spectra of the disordered material, which exhibit the same band edge as a uniform alloy with the average aluminum mole fraction of the multiple quantum well layer

Preliminary report into the effects of nitrogen ion bombardment treatment on mustard seeds

International Nuclear Information System (INIS)

Smith, C.W.; Al-Hashmi, S.A.R.; Ahmed, N.A.G.; Pollard, M.

1988-01-01

Mustard seeds have been subjected to nitrogen ion bombardment. A range of conditions was found within which there was an enhancement in the growth of seedlings from the ion bombardment treated seeds relative to those grown from control seeds. Scanning electron microscopy was used to examine seeds after treatment. It appeared that there had been an etching of the seed coating by the ion bombardment. This view was supported by experiments which showed that the rate of capillary water uptake by the treated seeds had been enhanced. (author)

Mechanical properties and internal fit of 4 CAD-CAM block materials.

Science.gov (United States)

Goujat, Alexis; Abouelleil, Hazem; Colon, Pierre; Jeannin, Christophe; Pradelle, Nelly; Seux, Dominique; Grosgogeat, Brigitte

2018-03-01

Recent polymer-based computer-assisted design and computer-assisted manufacturing (CAD-CAM) materials have been commercialized for inlay restorations, a polymer-infiltrated ceramic-network (PICN) and composite resin nanoceramics. Little independent evidence regarding their mechanical properties exists. Internal adaptation is an important factor for the clinical success and longevity of a restoration, and data concerning this parameter for inlays made with these blocks are scarce. The purpose of this in vitro study was to evaluate and compare the mechanical properties (flexural strength, flexural modulus, Vickers hardness, fracture toughness) and the internal adaptation of these recent polymer-based blocks with a lithium disilicate glass-ceramic block. The materials tested in this study were a PICN material (Vita Enamic), 2 composite resin nanoceramics (Lava Ultimate; 3M ESPE and Cerasmart; GCDental Products), and a lithium disilicate glass-ceramic (IPS e.max CAD). Mechanical properties were evaluated according to ISO norm DIS 6872:2013. Bar-shaped specimens (18×3×3 mm) were prepared and submitted to a 3-point bend test using a universal testing machine at a cross-head speed of 0.5 mm/min. In addition, identical cavities were prepared in 60 human mandibular extracted molars (n=15) and optically scanned to receive mesioocclusodistal inlays milled with the 4 materials tested in a CEREC Inlab milling machine. The replica technique and a stereomicroscope (×20) were used to measure the internal fit of the inlays at 9 preselected locations. All data were statistically analyzed using 1-way ANOVA and the post hoc Tukey multiple comparison or Games-Howell test (α=.05). The mean flexural strength of the tested blocks ranged from 148.7 ±9.5 MPa (Vita Enamic) to 216.5 ±28.3 MPa (Cerasmart). The mean flexural modulus ranged from 23.3 ±6.4 GPa (Vita Enamic) to 52.8 ±10.5 GPa (IPS e.max CAD). The mean Vickers hardness ranged from 0.66 ±0.02 GPa (Cerasmart) to 5.98 ±0

Influence of ion bombardment on structural and electrical properties of SiO2 thin films deposited from O2/HMDSO inductively coupled plasmas under continuous wave and pulsed modes

International Nuclear Information System (INIS)

Bousquet, A.; Goullet, A.; Leteinturier, C.; Granier, A.; Coulon, N.

2008-01-01

Low pressure Plasma Enhanced Chemical Vapour Deposition is commonly used to deposit insulators on temperature sensitive substrates. In these processes, the ion bombardment experienced by films during its growth is known to have benefits but also some disadvantages on material properties. In the present paper, we investigate the influence of this bombardment on the structure and the electrical properties of SiO 2 -like film deposited from oxygen/hexa-methyl-di-siloxane radiofrequency plasma in continuous and pulsed modes. First, we studied the ion kinetics thanks to time-resolved measurements by Langmuir probe. After, we showed the ion bombardment in such plasma controls the OH bond content in deposited films. Finally, we highlight the impressive reduction of fixed charge and interface state densities in films obtained in pulsed mode due to a lower ion bombardment. (authors)

Functional materials derived from block copolymer self-assembly

DEFF Research Database (Denmark)

Li, Tao

deposition methods, namely nanocasting and atomic layer deposition (ALD) will be applied to fabricate compact, inter-connected, and continuous metal oxide films. In this way, the structure integrity will be preserved after template removal during the annealing procedure. Another objective of this project......-casting, the block copolymer self-organizes into monolayer packed sphere pattern, without any surface treatment of the substrate and annealing process. Arrays of nano-pillars and nanowells of various materials are fabricated in dry etch processes over wafer scale without defects. We also show an in situ Al2O3 hard...

Structural changes IN THE Kh20N45M4B nickel alloys and THE Kh16N15M3B steel due to helium ion bombardment

International Nuclear Information System (INIS)

Kalin, B.A.; Chernikov, U.N.; Chernov, I.I.; Kozhevnikov, O.A.; Shishkin, G.N.; Yakushin, V.L.

1986-01-01

Using transmission electron microscopy, x-ray structural analysis, and the thermal desorption techniques, the authors carried out a detailed study of the structural and phase changes, defect formation, and helium accumulation in the He + -bombarded 16-15 austenitic steels and 20-45 nickel alloys. Microstructure of the bombarded specimens was studied using the methods of transmission electron microscopy of thin foils in the EVM-100, and EM-301G electron microscopes. Results of x-ray studies on the bombarded specimens are presented. The conducted studies show that bombardment of structural materials with light ions can lead to significant structural damages and changes in the chemical and phase composition of the surface layer. The possible mechanisms of the changes in the chemical and phase composition include selective sputtering and radiation-induced accelerated diffusion of elements in the field of internal lateral stresses developing during the He + implantation process

Kinetics of interaction from low-energy-ion bombardment of surfaces

International Nuclear Information System (INIS)

Horton, C.C.

1988-01-01

The kinetics of interaction from low energy oxygen ion bombardment of carbon and Teflon surfaces have been investigated. The surfaces were bombarded with 4.5 to 93 eV oxygen ions and emitted species were observed with a mass spectrometer. To obtain the kinetic information, the ion beam was square pulse modulated and reaction products were observed as a function of time. The kinetic information is contained in the response of the emitted species to the pulsed ion beam. Oxygen bombardment of carbon produced CO in three parallel branches with each following an adsorption-desorption process. The fast branch, with a rate constants of 12,000/sec, appeared to be sputter induced an was absent below about 19 eV. The medium and slow branches, with rate constants of 850/sec and 45/sec respectively, has little energy dependence and appeared to be due to chemical sputtering from two sites. The ratio of the fraction of the medium branch to that of the slow was constant at 1:3. The bombardment of Teflon produced CF in two parallel branches, with one following a series process and the other an adsorb-desorb process. The rate constant of the other branch were 22,000/sec and 7,000/sec and the rate constant of the other branch was 90/sec. The total signal fell monotonically with decreasing ion energy with the fraction for each branch holding constant at 71% for the series and 29% for the adsorb-desorb

Effects of hyperthermal proton bombardment on alkanethiol self-assembled monolayer on Au(1 1 1)

Energy Technology Data Exchange (ETDEWEB)

Xi Luan [Surface Science Western, University of Western Ontario, London, Ontario N6A 5B7 (Canada); Zheng Zhi; Lam, N.-S. [Department of Physics, Chinese University of Hong Kong, Shatin, Hong Kong (China); Grizzi, Oscar [Centro Atomico Bariloche, 8400 San Carlos de Bariloche, Rio Negro (Argentina); Lau, W.-M. [Surface Science Western, University of Western Ontario, London, Ontario N6A 5B7 (Canada)], E-mail: llau22@uwo.ca

2007-10-31

The effects of hyperthermal proton bombardment on alkanethiol self-assembled monolayer (SAM) on Au(1 1 1) are studied with scanning tunneling microscopy (STM) and X-ray photoemission spectroscopy (XPS). The STM and XPS results show that proton bombardment with proton energy as low as 2 eV can induce cross-linking of the adsorbed alkanethiols and transform the original ordered SAM lattice to an array of nanoclusters of the cross-linked alkanethiols. For a bombardment at 3 eV with a fluence of 3x10{sup 15} cm{sup -2}, the typical cluster size is about 5 nm. In addition, the cluster size distribution is narrow, with no cluster larger than 8 nm. The cluster growth can be promoted by increasing the fluence at a fixed bombardment energy or increasing the energy at a fixed fluence. This indicates that surface diffusion of alkanethiols and cluster growth can be harnessed by the control of the bombardment energy and fluence.

Effects of hyperthermal proton bombardment on alkanethiol self-assembled monolayer on Au(1 1 1)

International Nuclear Information System (INIS)

Xi Luan; Zheng Zhi; Lam, N.-S.; Grizzi, Oscar; Lau, W.-M.

2007-01-01

The effects of hyperthermal proton bombardment on alkanethiol self-assembled monolayer (SAM) on Au(1 1 1) are studied with scanning tunneling microscopy (STM) and X-ray photoemission spectroscopy (XPS). The STM and XPS results show that proton bombardment with proton energy as low as 2 eV can induce cross-linking of the adsorbed alkanethiols and transform the original ordered SAM lattice to an array of nanoclusters of the cross-linked alkanethiols. For a bombardment at 3 eV with a fluence of 3x10 15 cm -2 , the typical cluster size is about 5 nm. In addition, the cluster size distribution is narrow, with no cluster larger than 8 nm. The cluster growth can be promoted by increasing the fluence at a fixed bombardment energy or increasing the energy at a fixed fluence. This indicates that surface diffusion of alkanethiols and cluster growth can be harnessed by the control of the bombardment energy and fluence

Impact of Ion Bombardment on the Structure and Magnetic Properties of Fe78Si13B9 Amorphous Alloy

Science.gov (United States)

Wu, Yingwei; Peng, Kun

2018-06-01

Amorphous Fe78Si13B9 alloy ribbons were bombarded by ion beams with different incident angles ( θ ). The evolution of the microstructure and magnetic properties of ribbons caused by ion beam bombardment was investigated by x-ray diffraction, transmission electron microscope and vibrating sample magnetometer analysis. Low-incident-angle bombardment led to atomic migration in the short range, and high-incident-angle bombardment resulted in the crystallization of amorphous alloys. Ion bombardment induces magnetic anisotropy and affects magnetic properties. The effective magnetic anisotropy was determined by applying the law of approach to saturation, and it increased with the increase of the ion bombardment angle. The introduction of effective magnetic anisotropy will reduce the permeability and increase the relaxation frequency. Excellent high-frequency magnetic properties can be obtained by selecting suitable ion bombardment parameters.

Anomalous heat evolution of deuteron implanted Al on electron bombardment

International Nuclear Information System (INIS)

Kamada, K.; Kinoshita, H.; Takahashi, H.

1994-05-01

Anomalous heat evolution was observed in deuteron implanted Al foils on 175 keV electron bombardment. Local regions with linear dimension of several 100nm showed simultaneous transformation from single crystalline to polycrystalline structure instantaneously on the electron bombardment, indicating the temperature rise up to more than melting point of Al from room temperature. The amount of energy evolved was more than 180 MeV for each transformed region. The transformation was never observed in proton implanted Al foils. The heat evolution was considered due to a nuclear reaction in D 2 molecular collections. (author)

Light ions cyclotron bombardment to simulate fast neutron radiation damage in nuclear materials

International Nuclear Information System (INIS)

Segura, E.; Lucki, G.; Aguiar, D.

1984-01-01

The applicability and limitations of the use of cyclotron light ions bombardment to simulate the effects of the neutron irradiation are presented. Light ions with energies of about 10 MeV are capable to produce homogeneous damage in specimens suitable for measuring bulk mechanical properties although their low damage rate of 10 -5 dpa.sec -1 limit the dose range to a few dpa. On the other hand, cyclotron alpha particle implantation provides a fast and convenient way of introducing helium with a minimum of side effects so that we can take advantage of this technique to get better understanding of the mechanism by which this insoluble gas produces high temperature embrittlement. Some experimental details such as dimensions and cooling techniques are described. Finally a description of the infrastructure for cyclotron alpha particle implantation and a creep-test facility of the Division of Radiation Damage at IPEN-CNEN/SP are presented. (Author) [pt

ANALYTICAL MODELING OF ELECTRON BACK-BOMBARDMENT INDUCED CURRENT INCREASE IN UN-GATED THERMIONIC CATHODE RF GUNS

Energy Technology Data Exchange (ETDEWEB)

Edelen, J. P. [Fermilab; Sun, Y. [Argonne; Harris, J. R. [AFRL, NM; Lewellen, J. W. [Los Alamos Natl. Lab.

2016-09-28

In this paper we derive analytical expressions for the output current of an un-gated thermionic cathode RF gun in the presence of back-bombardment heating. We provide a brief overview of back-bombardment theory and discuss comparisons between the analytical back-bombardment predictions and simulation models. We then derive an expression for the output current as a function of the RF repetition rate and discuss relationships between back-bombardment, fieldenhancement, and output current. We discuss in detail the relevant approximations and then provide predictions about how the output current should vary as a function of repetition rate for some given system configurations.

Cluster induced chemistry at solid surfaces: Molecular dynamics simulations of keV C60 bombardment of Si

International Nuclear Information System (INIS)

Krantzman, K.D.; Kingsbury, D.B.; Garrison, Barbara J.

2007-01-01

Molecular dynamics simulations of the sputtering of Si by keV C 60 bombardment have been performed as a function of incident kinetic energy at two incident angles, normal incidence and 45 deg. Nearly all of the C atoms remain embedded in the surface after bombardment because the C atoms from the projectile form strong covalent bonds with the Si atoms in the target. At low incident kinetic energies, the sputtering yield of Si atoms is small and there is a net deposition of solid material from the projectile atoms. As the incident kinetic energy is increased, the yield of sputtered Si atoms increases. A transition occurs in which the yield of sputtered Si atoms exceeds the number of C atoms deposited, and there is a net erosion of the solid material. A significantly higher sputter yield is observed at an incident angle of 45 deg. than at normal incidence, and therefore, the energy value is lower for the transition from net deposition to net erosion. This phenomenon is discussed in terms of the depth distribution of deposited energy, which is found to be shallower at an incident angle of 45 deg

Ion bombardment damage in a modified Fe-9Cr-1Mo steel

International Nuclear Information System (INIS)

Farrell, K.; Lee, E.H.

1984-01-01

A normalized-and-tempered Fe-9Cr-1Mo steel, with small Nb and V additions, was bombarded with 4-MeV iron ions to 100 dpa at 400, 450, 500, 550, and 600 0 C. Major damage feature was dislocation tangles which coarsened with increasing bombardment temperature. Sparse cavities were heterogeneously distributed at 500 and 550 0 C. Incorporation of helium and deuterium simultaneously in the bombardments at rates of 10 and 45 appM/dpa, respectively, introduced very high concentrations of small cavities at all temperatures, many of them on grain boundaries. These cavities were shown to be promoted by helium. A small fraction of the matrix cavities exhibited bias-driven growth at 500 and 550 0 C, with swelling 0 C higher than the peak swelling temperature found in neutron irradiations, which is compatible with the higher damage rate used in the ion bombardments. High concentrations of subgrain boundaries and dislocations resulting from the heat treatment, and unbalanced cavity and dislocation sink strengths in the damage structures contribute to the swelling resistance. Such resistance may not be permanent. High densities of bubbles on grain boundaries indicate a need for helium embrittlement tests

Main-chain supramolecular block copolymers.

Science.gov (United States)

Yang, Si Kyung; Ambade, Ashootosh V; Weck, Marcus

2011-01-01

Block copolymers are key building blocks for a variety of applications ranging from electronic devices to drug delivery. The material properties of block copolymers can be tuned and potentially improved by introducing noncovalent interactions in place of covalent linkages between polymeric blocks resulting in the formation of supramolecular block copolymers. Such materials combine the microphase separation behavior inherent to block copolymers with the responsiveness of supramolecular materials thereby affording dynamic and reversible materials. This tutorial review covers recent advances in main-chain supramolecular block copolymers and describes the design principles, synthetic approaches, advantages, and potential applications.

Hydrogen pumping and release by graphite under high flux plasma bombardment

International Nuclear Information System (INIS)

Hirooka, Y.; Leung, W.K.; Conn, R.W.; Goebel, D.M.; LaBombard, B.; Nygren, R.; Wilson, K.L.

1988-01-01

Inert gas (helium or argon) plasma bombardment has been found to increase the surface gas adsorptivity of isotropic graphite (POCO-graphite), which can then getter residual gases in a high vacuum system. The inert gas plasma bombardment was carried out at a flux ≅ 1 x 10 18 ions s -1 cm -2 to a fluence of the order of 10 21 ions/cm 2 and at temperatures around 800 0 C. The gettering capability of graphite can be easily recovered by repeating inert gas plasma bombardment. The activated graphite surface exhibits a smooth, sponge-like morphology with significantly increased pore openings, which correlates with the observed increase in the surface gas adsorptivity. The activated graphite surface has been observed to pump hydrogen plasma particles as well. From calibrated H-alpha measurements, the dynamic hydrogen retention capacity is evaluated to be as large as 2 x 10 18 H/cm 2 at temperatures below 100 0 C and at a plasma bombarding energy of 300 eV. The graphite temperature was varied between 15 and 480 0 C. Due to the plasma particle pumping capability, hydrogen recycling from the activated graphite surface is significantly reduced, relative to that from a pre-saturated surface. A pre-saturated surface was also observed to reproducibly pump a hydrogen plasma to a concentration of 9.5 x 10 17 H/cm 2 . The hydrogen retention capacity of graphite is found to decrease with increasing temperature. A transient pumping mechanism associated with the sponge-like surface morphology is conjectured to explain the large hydrogen retention capacity. Hydrogen release behavior under helium and argon plasma bombardment was also investigated, and the result indicated the possibility of some in-pore retrapping effect. 43 refs., 11 figs

Microbial habitability of the Hadean Earth during the late heavy bombardment

Science.gov (United States)

Abramov, Oleg; Mojzsis, Stephen J.

2009-05-01

Lunar rocks and impact melts, lunar and asteroidal meteorites, and an ancient martian meteorite record thermal metamorphic events with ages that group around and/or do not exceed 3.9Gyr. That such a diverse suite of solar system materials share this feature is interpreted to be the result of a post-primary-accretion cataclysmic spike in the number of impacts commonly referred to as the late heavy bombardment (LHB). Despite its obvious significance to the preservation of crust and the survivability of an emergent biosphere, the thermal effects of this bombardment on the young Earth remain poorly constrained. Here we report numerical models constructed to probe the degree of thermal metamorphism in the crust in the effort to recreate the effect of the LHB on the Earth as a whole; outputs were used to assess habitable volumes of crust for a possible near-surface and subsurface primordial microbial biosphere. Our analysis shows that there is no plausible situation in which the habitable zone was fully sterilized on Earth, at least since the termination of primary accretion of the planets and the postulated impact origin of the Moon. Our results explain the root location of hyperthermophilic bacteria in the phylogenetic tree for 16S small-subunit ribosomal RNA, and bode well for the persistence of microbial biospheres even on planetary bodies strongly reworked by impacts.

Microbial habitability of the Hadean Earth during the late heavy bombardment.

Science.gov (United States)

Abramov, Oleg; Mojzsis, Stephen J

2009-05-21

Lunar rocks and impact melts, lunar and asteroidal meteorites, and an ancient martian meteorite record thermal metamorphic events with ages that group around and/or do not exceed 3.9 Gyr. That such a diverse suite of solar system materials share this feature is interpreted to be the result of a post-primary-accretion cataclysmic spike in the number of impacts commonly referred to as the late heavy bombardment (LHB). Despite its obvious significance to the preservation of crust and the survivability of an emergent biosphere, the thermal effects of this bombardment on the young Earth remain poorly constrained. Here we report numerical models constructed to probe the degree of thermal metamorphism in the crust in the effort to recreate the effect of the LHB on the Earth as a whole; outputs were used to assess habitable volumes of crust for a possible near-surface and subsurface primordial microbial biosphere. Our analysis shows that there is no plausible situation in which the habitable zone was fully sterilized on Earth, at least since the termination of primary accretion of the planets and the postulated impact origin of the Moon. Our results explain the root location of hyperthermophilic bacteria in the phylogenetic tree for 16S small-subunit ribosomal RNA, and bode well for the persistence of microbial biospheres even on planetary bodies strongly reworked by impacts.

Stable transformation via particle bombardment in two different soybean regeneration systems.

Science.gov (United States)

Sato, S; Newell, C; Kolacz, K; Tredo, L; Finer, J; Hinchee, M

1993-05-01

The Biolistics(®) particle delivery system for the transformation of soybean (Glycine max L. Merr.) was evaluated in two different regeneration systems. The first system was multiple shoot proliferation from shoot tips obtained from immature zygotic embryos of the cultivar Williams 82, and the second was somatic embryogenesis from a long term proliferative suspension culture of the cultivar Fayette. Bombardment of shoot tips with tungsten particles, coated with precipitated DNA containing the gene for β-glucuronidase (GUS), produced GUS-positive sectors in 30% of the regenerated shoots. However, none of the regenerants which developed into plants continued to produce GUS positive tissue. Bombardment of embryogenic suspension cultures produced GUS positive globular somatic embryos which proliferated into GUS positive somatic embryos and plants. An average of 4 independent transgenic lines were generated per bombarded flask of an embryogenic suspension. Particle bombardment delivered particles into the first two cell layers of either shoot tips or somatic embryos. Histological analysis indicated that shoot organogenesis appeared to involve more than the first two superficial cell layers of a shoot tip, while somatic embryo proliferation occurred from the first cell layer of existing somatic embryos. The different transformation results obtained with these two systems appeared to be directly related to differences in the cell types which were responsible for regeneration and their accessibility to particle penetration.

Standard test method for ranking resistance of materials to sliding wear using block-on-ring wear test

CERN Document Server

American Society for Testing and Materials. Philadelphia

2005-01-01

1.1 This test method covers laboratory procedures for determining the resistance of materials to sliding wear. The test utilizes a block-on-ring friction and wear testing machine to rank pairs of materials according to their sliding wear characteristics under various conditions. 1.2 An important attribute of this test is that it is very flexible. Any material that can be fabricated into, or applied to, blocks and rings can be tested. Thus, the potential materials combinations are endless. However, the interlaboratory testing has been limited to metals. In addition, the test can be run with various lubricants, liquids, or gaseous atmospheres, as desired, to simulate service conditions. Rotational speed and load can also be varied to better correspond to service requirements. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Wear test results are reported as the volume loss in cubic millimetres for both the block and ring. Materials...

Light irradiance through novel CAD-CAM block materials and degree of conversion of composite cements.

Science.gov (United States)

Lise, Diogo Pedrollo; Van Ende, Annelies; De Munck, Jan; Yoshihara, Kumiko; Nagaoka, Noriyuki; Cardoso Vieira, Luiz Clovis; Van Meerbeek, Bart

2018-02-01

To assess light irradiance (LI) delivered by two light-curing units (LCU's) and to measure the degree of conversion (DC) of three composite cements, when cured through different thicknesses of two novel CAD-CAM block materials. 100-μm-thick films of a dual-curable composite cement (G-CEM LinkAce, GC), a light-curable flowable resin-based composite (RBC) (G-ænial Universal Flo, GC) and a micro-hybrid RBC (G-ænial Posterior, GC) were investigated as luting agents. Two 'polymer-ceramic' CAD-CAM blocks (Cerasmart, GC; Enamic, Vita Zahnfabrik) were sectioned in slabs with different thicknesses (1, 3 and 5mm). LI at the bottom of the specimens was measured using a calibrated spectrometer, while being light-cured through the CAD-CAM block slabs for 40s with a low- (±500mW/cm 2 ) or high- (±1,600mW/cm 2 ) irradiance LCU (n=5). After light-curing, micro-Raman spectra of the composite films were acquired to determine DC at 5min, 10min, 1h and 24h. LI data were statistically analyzed by Kruskal-Wallis followed by post-hoc comparisons, while a linear mixed-effect model was applied for the DC analysis. In addition, the CAD-CAM blocks ultrastructure was characterized upon argon-ion slicing using scanning transmission electron microscopy (STEM). Finally, light transmission (LT) through each CAD-CAM block material was assessed using a spectrophotometer. Curing-light attenuation and DC were significantly influenced by thickness and type of the overlying material. LCU only had a significant effect on DC of the micro-hybrid RBC. DC significantly increased over time for all composite cements. CAD-CAM block structural analysis revealed a relatively small and homogenous filler configuration (mean filler size of 0.2-0.5μm) for Cerasmart, while Enamic contained ceramic grains varying in shape and size (1-10μm), which were interconnected by the polymer-based network. LT was much higher at a wavelength range of 300-800nm for Cerasmart than for Enamic. Light-curable composite cements

Direct evidence for a thermal effect of Ar+ ion bombardment in a conventional sputtering mode

International Nuclear Information System (INIS)

Okuyama, F.; Fujimoto, Y.

1986-01-01

Evidence is presented that the Ar + ion bombardment for sputtering in Auger electron spectroscopy can heat the target up to 2000 0 C if the target has poor heat conduction. Polycrystalline microneedles of Cr exhibited spherical tips after being exposed to 3 keV Ar + ions, proving that the needle tips were melted by impacting Ar + ions. Microneedles of Mo ion bombarded under the same condition were bent plastically, which perhaps reflects the thermal annealing of the needles during ion bombardment

Plasmonic Glasses and Films Based on Alternative Inexpensive Materials for Blocking Infrared Radiation.

Science.gov (United States)

V Besteiro, Lucas; Kong, Xiang-Tian; Wang, Zhiming; Rosei, Federico; Govorov, Alexander O

2018-04-16

The need for energy-saving materials is pressing. This Letter reports on the design of energy-saving glasses and films based on plasmonic nanocrystals that efficiently block infrared radiation. Designing such plasmonic composite glasses is nontrivial and requires taking full advantage of both material and geometrical properties of the nanoparticles. We compute the performance of solar plasmonic glasses incorporating a transparent matrix and specially shaped nanocrystals. This performance depends on the shape and material of such nanocrystals. Glasses designed with plasmonic nanoshells are shown to exhibit overall better performances as compared to nanorods and nanocups. Simultaneously, scalable synthesis of plasmonic nanoshells and nanocups is technologically feasible using gas-phase fabrication methods. The computational simulations were performed for noble metals (gold and silver) as well as for alternative plasmonic materials (aluminum, copper, and titanium nitride). Inexpensive plasmonic materials (silver, copper, aluminum, and titanium nitride) show an overall good performance in terms of the commonly used figures of merit of industrial glass windows. Together with numerical data for specific materials, this study includes a set of general rules for designing efficient plasmonic IR-blocking media. The plasmonic glasses proposed herein are good candidates for the creation of cheap optical media, to be used in energy-saving windows in warm climates' housing or temperature-sensitive infrastructure.

Changes in surface morphology and microcrack initiation in polymers under simultaneous exposure to stress and fast atom bombardment

International Nuclear Information System (INIS)

Michael, R.S.; Frank, S.; Stulik, D.; Dickinson, J.T.

1987-01-01

The authors present studies of the changes in surface morphology due to simultaneous exposure of polymers to stress and fast atom bombardment. The polymers examined were Teflon, Kapton, Nylon, and Kevlar-49. The incident particles were 6 keV xenon atoms. The authors show that in the presence of mechanical stress these polymers show topographical changes at particle doses considerably lower than similar changes produced on unstressed material. Applied stress also promotes the formation of surface microcracks which could greatly reduce mechanical strength of the material

Effect of the ion bombardment on the apparent barrier height in GaAs Schottky junctions

International Nuclear Information System (INIS)

Horvath, Zs. J.

1994-01-01

The bombardment of the semiconductor with different particles often results in the change of the doping concentration at the semiconductor surface. In this paper the effects of this near-interface concentration change on the apparent and real Schottky barrier heights are discussed. Experimental results obtained in GaAs Schottky junctions prepared on ion-bombarded semiconductor surfaces are analysed, and it is shown that their electrical characteristics are strongly influenced by the near-interface concentration change due to the ion bombardment. (author). 36 refs., 2 figs

Development of pits and cones on ion bombarded copper

International Nuclear Information System (INIS)

Tanovic, L.A.; Carter, G.; Nobes, M.J.; Whitton, I.L.; Williams, J.S.

1980-01-01

The formation of pits and cones on Ar ion bombarded copper has been studied. Carefully polished surfaces of large grained 99.999% pure copper crystals have been bombarded at normal incidence with 40 keV argon ions. The cone formation has been investigated for annealed and non-annealed crystals at room temperature and at 30 K and in the case of monocrystal and polycrystal samples. Although in the most other studies the presence of impurities is as a necessary condition for generation of cones and pits the obtained experimental results show that under certain conditions these features are formed on clean surfaces. It is shown that the dominant parameter in the production of cones on copper is the crystal orientation [ru

Diffusion processes in bombardment-induced surface topography

International Nuclear Information System (INIS)

Robinson, R.S.

1984-01-01

A treatment is given of the problem of surface diffusion processes occurring during surface topography development, whenever a surface is simultaneously seeded with impurities and ion bombarded. The development of controllable topography and the importance of surface diffusion parameters, which can be obtained during these studies, are also analyzed. 101 refs.; 7 figs.; 2 tabs

Effects of low and high energy ion bombardment on ETFE polymer

Science.gov (United States)

Minamisawa, R. A.; De Almeida, A.; Abidzina, V.; Parada, M. A.; Muntele, I.; Ila, D.

2007-04-01

The polymer ethylenetetrafluoroethylene (ETFE) is used as anti-adherent coatings for food packages and radiation dosimeters. In this work, we compare the damage induced in ETFE bombarded with 100 keV Si ions with that induced by 1 MeV proton bombardment. The damage depends on the type, energy and intensity of the irradiation. Irradiated films were analyzed with optical absorption photospectrometry, Raman spectroscopy and Fourier transform infrared (FTIR) spectroscopy to determine the chemical nature of the structural changes caused by ion irradiation. Computer simulations were performed to evaluate the radiation damage.

Particle-In-Cell/Monte Carlo Simulation of Ion Back Bombardment in Photoinjectors

International Nuclear Information System (INIS)

Qiang, Ji; Corlett, John; Staples, John

2009-01-01

In this paper, we report on studies of ion back bombardment in high average current dc and rf photoinjectors using a particle-in-cell/Monte Carlo method. Using H 2 ion as an example, we observed that the ion density and energy deposition on the photocathode in rf guns are order of magnitude lower than that in a dc gun. A higher rf frequency helps mitigate the ion back bombardment of the cathode in rf guns

Evidence Supporting an Early as Well as Late Heavy Bombardment on the Moon

Science.gov (United States)

Frey, Herbert

2015-01-01

Evidence supporting an intense early bombardment on the Moon in addition to the traditional Late Heavy Bombardment at approx. 4 BY ago include the distribution of N(50) Crater Retention Ages (CRAs) for candidate basins, a variety of absolute age scenarios for both a "young" and an "old" Nectaris age, and the decreasing contrasts in both topographic relief and Bouguer gravity with increasing CRA.

Modified conductivity of polymer materials with proton beam

International Nuclear Information System (INIS)

Matsumoto, Shinji; Seki, Miharu; Shima, Kunihiro; Ishihara, Toyoyuki

2001-01-01

Ionic conductivity of polymer materials is of increasing interest in many scientific fields. Industrial applications seem to be promising. In the present investigation, we used proton bombardment to modify the characteristic properties of polymers, especially for improvement in conductivity and hardening gel polymers. Particle beam bombardment is known to produce many scissions by particle passages and new bonds by bridge connection. These effects may modify various properties in many ways. We examined the modification of conductivity in solid polymers composed of polyethylene oxide and polyurethane and the surface appearance of gel polymers with bombardment by a proton beam using the accelerator facility of Tsukuba University. The results indicated proton bombardment induced conductivity changes in various ways according to particle range and polymer properties. (author)

Silicon transport in sputter-deposited tantalum layers grown under ion bombardment

International Nuclear Information System (INIS)

Gallais, P.; Hantzpergue, J.J.; Remy, J.C.; Roptin, D.

1988-01-01

Tantalum was sputter deposited on (111) Si substrate under low-energy ion bombardment in order to study the effects of the ion energy on the silicon transport into the Ta layer. The Si substrate was heated up to 500 0 C during growth. For ion energies up to 180 eV silicon is not transported into tantalum and the growth temperature has no effect. An ion bombardment energy of 280 eV enhances the transport of silicon throughout the tantalum layer. Growth temperatures up to 300 0 C have no effect on the silicon transport which is mainly enhanced by the ion bombardment. For growth temperatures between 300 and 500 0 C, the silicon transport is also enhanced by the thermal diffusion. The experimental depth distribution of silicon is similar to the theoretical depth distribution calculated for the case of an interdiffusion. The ion-enhanced process of silicon transport is characterized by an activation energy of 0.4 eV. Silicon into the layers as-grown at 500 0 C is in both states, amorphous silicide and microcrystalline cubic silicon

Structural and magnetic properties of ion-beam bombarded Co/Pt multilayers

Energy Technology Data Exchange (ETDEWEB)

Lin, K.W.; Guo, J.Y.; Lin, S.R.; Ouyang, H. [Department of Materials Science and Engineering, National Chung Hsing University, Taichung 402 (China); Tsai, C.J. [Department of Materials Science and Engineering, National Tsing Hua University, Hsinchu 300 (China); Van Lierop, J. [Department of Physics and Astronomy, University of Manitoba, Winnipeg (Canada); Phuoc, N.N.; Suzuki, T. [Information Storage Materials Laboratory, Toyota Technological Institute, Nagoya 468-8511 (Japan)

2007-12-15

A series of [Pt(2 nm)/Co(2 nm)]{sub 10}/Pt(30 nm) multilayers were deposited by using an ion-beam technique. X-ray diffraction and transmission electron microscopy results have shown that as-deposited samples consist of h.c.p. Co and f.c.c. Pt phases. Disordered CoPt{sub 3} phases were developed with increasing End-Hall voltage (V{sub EH}) that induces greater ion-beam bombardment energy during deposition. This indicates that intermixing of Co and Pt increases with ion-beam bombardment. The coercivities (ranging from 100 Oe to 300 Oe) of Co/Pt multilayers decreased with increasing V{sub EH}. After annealing, the formation of CoPt{sub 3} was observed in these ion-beam bombarded samples, resulting in lower coercivities (H{sub c}{proportional_to} 50 Oe). The depressed transition temperature of CoPt{sub 3} for films deposited with the largest V{sub EH} was attributed to distorted CoPt{sub 3} structures that appeared with annealing. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

The surface topography of Inconel, stainless steel and copper after argon ion bombardment

International Nuclear Information System (INIS)

Vogelbruch, K.; Vietzke, E.

1983-01-01

Energetic particle bombardment of metals is known to change the surface topography. To simulate the behaviour of the first wall of a fusion device under real plasma conditions, we have investigated the surface topography of rotating targets after 30 keV argon ion bombardment at 70deg incident angle by electron scanning micrographs. Under these conditions Inconel 600, 601, 625, stainless steel, and copper showed no cones, pyramids or cliffs, but only etching figures and at higher ion doses relatively flat hills. Thus, it can be concluded, that the influence of energetic particles on the first wall of a fusion reactor is smaller than expected from the results of such sputtering experiments, which have dealt with the formation of surface structures under ion bombardment at constant incident direction. (author)

Nano-porous Material with Spherical or Gyroid Cavities Created by Quantitative Etching of Polydimethylsiloxane in Polystyrene-Polydimethylsiloxane Block Copolymers

DEFF Research Database (Denmark)

Ndoni, Sokol; Vigild, Martin Etchells; Berg, Rolf H.

2003-01-01

A new method for quantitative etching of the poly(dimethylsiloxane) block in polystyrene-poly(dimethylsiloxane) (PS-PDMS) block copolymers is reported. Reacting the block copolymer with anhydrous hydrogen fluoride renders a nanoporous material (NPM) with the remaining glassy PS maintaining...... the original bulk morphology. 1H NMR, mass difference, size exclusion chromatography, and X-ray photoelectron spectroscopy were used to characterize the materials before and after etching. NPMs containing spherical and gyroid cavities were prepared, as ascertained by small-angle X-ray scattering...

HCN Production via Impact Ejecta Reentry During the Late Heavy Bombardment

Science.gov (United States)

Parkos, Devon; Pikus, Aaron; Alexeenko, Alina; Melosh, H. Jay

2018-04-01

Major impact events have shaped the Earth as we know it. The Late Heavy Bombardment is of particular interest because it immediately precedes the first evidence of life. The reentry of impact ejecta creates numerous chemical by-products, including biotic precursors such as HCN. This work examines the production of HCN during the Late Heavy Bombardment in more detail. We stochastically simulate the range of impacts on the early Earth and use models developed from existing studies to predict the corresponding ejecta properties. Using multiphase flow methods and finite-rate equilibrium chemistry, we then find the HCN production due to the resulting atmospheric heating. We use Direct Simulation Monte Carlo to develop a correction factor to account for increased yields due to thermochemical nonequilibrium. We then model 1-D atmospheric turbulent diffusion to find the time accurate transport of HCN to lower altitudes and ultimately surface water. Existing works estimate the necessary HCN molarity threshold to promote polymerization that is 0.01 M. For a mixing depth of 100 m, we find that the Late Heavy Bombardment will produce at least one impact event above this threshold with probability 24.1% for an oxidized atmosphere and 56.3% for a partially reduced atmosphere. For a mixing depth of 10 m, the probability is 79.5% for an oxidized atmosphere and 96.9% for a partially reduced atmosphere. Therefore, Late Heavy Bombardment impact ejecta is likely an HCN source sufficient for polymerization in shallow bodies of water, particularly if the atmosphere were in a partially reduced state.

Effect of helium ion bombardment on hydrogen behaviour in stainless steel

International Nuclear Information System (INIS)

Guseva, M.I.; Stolyarova, V.G.; Gorbatov, E.A.

1987-01-01

The effect of helium ion bombardment on hydrogen behaviour in 12Kh18N10T stainless steel is investigated. Helium and hydrogen ion bombardment was conducted in the ILU-3 ion accelerator; the fluence and energy made up 10 16 -5x10 17 cm -2 , 30 keV and 10 16 -5x10 18 cm -2 , 10 keV respectively. The method of recoil nuclei was used for determination of helium and hydrogen content. Successive implantation of helium and hydrogen ions into 12Kh18N10T stainless steel results in hydrogen capture by defects formed by helium ions

Effect of cyclic block loading on character of deformation and strength of structural materials in plane stressed state

International Nuclear Information System (INIS)

Kul'chitskij, N.M.; Troshchenko, A.V.; Koval'chuk, B.I.; Khamaza, L.A.; Nikolaev, I.A.

1982-01-01

The paper is concerned with choice of conditions for preliminary cyclic block loading, determination of fatigue failure resistance characteristics for various structural materials under regular and selected block loading, investigation of the preliminary cyclic loading effect on regularities of elastoplastic deformation of materials concerned in the biaxial stressed state. Under selected conditions of cyclic block loading the character of damage accumulation is close to the linear law for the materials of high-srength doped steel, and VT6 alloys of concern. These materials in the initial state and after preliminary cyclic loading are anisotropic. Axial direction is characterized by a higher plastic strain resistance for steel and tangential direction - for VT6 alloy. The generalized strain curves for the materials in question are not invariant as to the stressed state type. It is stated that the effect of preliminary unsteady cyclic loading on resistance and general regularities of material deformation in the complex stressed state is insignificant. It is observed that stress-strain properties of the materials tend to vary in the following way: plastic strain resistance of the steel lowers and that of VT6 rises, anisotropy of the materials somehow decreases. The variation in the material anisotropy may be attributed to a decrease in residual stresses resulting from preliminary cyclic loading

Neutron yields from bombardment of α-particles

International Nuclear Information System (INIS)

Nakasima, Ryuzo

1982-09-01

The thick target neutron yields from bombardment of <10 MeV α-particles are calculated based on the reaction cross sections. The results for the elements of Z < 15 are compared with existing calculated or measured neutron yield data. For the elements of 16 < Z < 50, elemental or isotopic neutron yields are calculated if the cross section data are available. (author)

Population Blocks.

Science.gov (United States)

Smith, Martin H.

1992-01-01

Describes an educational game called "Population Blocks" that is designed to illustrate the concept of exponential growth of the human population and some potential effects of overpopulation. The game material consists of wooden blocks; 18 blocks are painted green (representing land), 7 are painted blue (representing water); and the remaining…

Suppression of self-organized surface nanopatterning on GaSb/InAs multilayers induced by low energy oxygen ion bombardment by using simultaneously sample rotation and oxygen flooding

Science.gov (United States)

Beainy, Georges; Cerba, Tiphaine; Bassani, Franck; Martin, Mickaël; Baron, Thierry; Barnes, Jean-Paul

2018-05-01

Time of flight secondary ion mass spectrometry (ToF-SIMS) is a well-adapted analytical method for the chemical characterization of concentration profiles in layered or multilayered materials. However, under ion beam bombardment, initially smooth material surface becomes morphologically unstable. This leads to abnormal secondary ion yields and depth profile distortions. In this contribution, we explore the surface topography and roughening evolution induced by O2+ ion bombardment on GaSb/InAs multilayers. We demonstrate the formation of nanodots and ripples patterning according to the ion beam energy. Since the latter are undesirable for ToF-SIMS analysis, we managed to totally stop their growth by using simultaneously sample rotation and oxygen flooding. This unprecedented coupling between these two latter mechanisms leads to a significant enhancement in depth profiles resolution.

Ti-doped isotropic graphite: A promising armour material for plasma-facing components

Science.gov (United States)

García-Rosales, C.; López-Galilea, I.; Ordás, N.; Adelhelm, C.; Balden, M.; Pintsuk, G.; Grattarola, M.; Gualco, C.

2009-04-01

Finely dispersed Ti-doped isotropic graphites with 4 at.% Ti have been manufactured using synthetic mesophase pitch 'AR' as raw material. These new materials show a thermal conductivity at room temperature of ˜200 W/mK and flexural strength close to 100 MPa. Measurement of the total erosion yield by deuterium bombardment at ion energies and sample temperatures for which pure carbon shows maximum values, resulted in a reduction of at least a factor of 4, mainly due to dopant enrichment at the surface caused by preferential erosion of carbon. In addition, ITER relevant thermal shock loads were applied with an energetic electron beam at the JUDITH facility. The results demonstrated a significantly improved performance of Ti-doped graphite compared to pure graphite. Finally, Ti-doped graphite was successfully brazed to a CuCrZr block using a Mo interlayer. These results let assume that Ti-doped graphite can be a promising armour material for divertor plasma-facing components.

Ti-doped isotropic graphite: A promising armour material for plasma-facing components

Energy Technology Data Exchange (ETDEWEB)

Garcia-Rosales, C. [CEIT and Tecnun (University of Navarra), Paseo de Manuel Lardizabal, 15, E-20018 San Sebastian (Spain)], E-mail: cgrosales@ceit.es; Lopez-Galilea, I.; Ordas, N. [CEIT and Tecnun (University of Navarra), Paseo de Manuel Lardizabal, 15, E-20018 San Sebastian (Spain); Adelhelm, C.; Balden, M. [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, D-85748 Garching (Germany); Pintsuk, G. [Forschungszentrum Juelich GmbH, EURATOM Association, D-52425 Juelich (Germany); Grattarola, M.; Gualco, C. [Ansaldo Ricerche S.p.A., I-16152 Genoa (Italy)

2009-04-30

Finely dispersed Ti-doped isotropic graphites with 4 at.% Ti have been manufactured using synthetic mesophase pitch 'AR' as raw material. These new materials show a thermal conductivity at room temperature of {approx}200 W/mK and flexural strength close to 100 MPa. Measurement of the total erosion yield by deuterium bombardment at ion energies and sample temperatures for which pure carbon shows maximum values, resulted in a reduction of at least a factor of 4, mainly due to dopant enrichment at the surface caused by preferential erosion of carbon. In addition, ITER relevant thermal shock loads were applied with an energetic electron beam at the JUDITH facility. The results demonstrated a significantly improved performance of Ti-doped graphite compared to pure graphite. Finally, Ti-doped graphite was successfully brazed to a CuCrZr block using a Mo interlayer. These results let assume that Ti-doped graphite can be a promising armour material for divertor plasma-facing components.

Ti-doped isotropic graphite: A promising armour material for plasma-facing components

International Nuclear Information System (INIS)

Garcia-Rosales, C.; Lopez-Galilea, I.; Ordas, N.; Adelhelm, C.; Balden, M.; Pintsuk, G.; Grattarola, M.; Gualco, C.

2009-01-01

Finely dispersed Ti-doped isotropic graphites with 4 at.% Ti have been manufactured using synthetic mesophase pitch 'AR' as raw material. These new materials show a thermal conductivity at room temperature of ∼200 W/mK and flexural strength close to 100 MPa. Measurement of the total erosion yield by deuterium bombardment at ion energies and sample temperatures for which pure carbon shows maximum values, resulted in a reduction of at least a factor of 4, mainly due to dopant enrichment at the surface caused by preferential erosion of carbon. In addition, ITER relevant thermal shock loads were applied with an energetic electron beam at the JUDITH facility. The results demonstrated a significantly improved performance of Ti-doped graphite compared to pure graphite. Finally, Ti-doped graphite was successfully brazed to a CuCrZr block using a Mo interlayer. These results let assume that Ti-doped graphite can be a promising armour material for divertor plasma-facing components.

Flexural resistance of Cerec CAD/CAM system ceramic blocks. Part 2: Outsourcing materials.

Science.gov (United States)

Sedda, Maurizio; Vichi, Alessandro; Del Siena, Francesco; Louca, Chris; Ferrari, Marco

2014-02-01

To test different Cerec CAD/CAM system ceramic blocks, comparing mean flexural strength (sigma), Weibull modulus (m), and Weibull characteristic strength (sigma0) in an ISO standardized set-up. Following the recent ISO Standard (ISO 6872:2008), 11 types of ceramic blocks were tested: IPS e.max CAD MO, IPS e.max CAD LT and IPS e.max CAD HT (lithium disilicate glass-ceramic); In-Ceram SPINELL, In-Ceram Alumina and In-Ceram Zirconia (glass-infiltrated materials); inCoris AL and In-Ceram AL (densely sintered alumina); In-Ceram YZ, IPS e.max Zir-CAD and inCoris ZI (densely sintered zirconia). Specimens were cut out from ceramic blocks, finished, crystallized/infiltrated/sintered, polished, and tested in a three-point bending test apparatus. Flexural strength, Weibull characteristic strength, and Weibull modulus were obtained. A statistically significant difference was found (P ceramic (sigma = 272.6 +/- 376.8 MPa, m = 6.2 +/- 11.3, sigma0 = 294.0 +/- 394.1 MPa) and densely sintered alumina (sigma = 441.8 +/- 541.6 MPa, m = 11.9 +/- 19.0, sigma0 = 454.2 +/- 565.2 MPa). No statistically significant difference was found (P = 0.254) in glass infiltrated materials (sigma = 376.9 +/- 405.5 MPa, m = 7.5 +/- 11.5, sigma0 = 393.7 +/- 427.0 MPa). No statistically significant difference was found (P = 0.160) in densely sintered zirconia (sigma = 1,060.8 +/- 1,227.8 MPa, m = 5.8 +/- 7.4, sigma0 = 1,002.4 +/- 1,171.0 MPa). Not all the materials tested fulfilled the requirements for the clinical indications recommended by the manufacturer.

MD and BCA simulations of He and H bombardment of fuzz in bcc elements

Science.gov (United States)

Klaver, T. P. C.; Zhang, S.; Nordlund, K.

2017-08-01

We present results of MD simulations of low energy He ion bombardment of low density fuzz in bcc elements. He ions can penetrate several micrometers into sparse fuzz, which allows for a sufficient He flux through it to grow the fuzz further. He kinetic energy falls off exponentially with penetration depth. A BCA code was used to carry out the same ion bombardment on the same fuzz structures as in MD simulations, but with simpler, 10 million times faster calculations. Despite the poor theoretical basis of the BCA at low ion energies, and the use of somewhat different potentials in MD and BCA calculations, the ion penetration depths predicted by BCA are only ∼12% less than those predicted by MD. The MD-BCA differences are highly systematic and trends in the results of the two methods are very similar. We have carried out more than 200 BCA calculation runs of ion bombardment of fuzz, in which parameters in the ion bombardment process were varied. For most parameters, the results show that the ion bombardment process is quite generic. The ion species (He or H), ion mass, fuzz element (W, Ta, Mo, Fe) and fuzz element lattice parameter turned out to have a modest influence on ion penetration depths at most. An off-normal angle of incidence strongly reduces the ion penetration depth. Increasing the ion energy increases the ion penetration, but the rate by which ion energy drops off at high ion energies follows the same exponential pattern as at lower energies.

Ion bombardment effects on surface states in selected oxide systems: rutile and alkaline earth titanates

International Nuclear Information System (INIS)

Gruen, D.M.

1978-01-01

In this paper, the nature of the surface states of n-type TiO 2 and SrTiO 3 is discussed and the role of ion bombardment in modifying the properties of these states is elucidated. Insofar as possible, the interrelationships between oxide nonstoichiometry, surface states, ion bombardment effects and photoelectrolysis are explored

Theoretical simulations of atomic and polyatomic bombardment of an organic overlayer on a metallic substrate

CERN Document Server

Krantzman, K D; Delcorte, A; Garrison, B J

2003-01-01

Our previous molecular dynamics simulations on initial test systems have laid the foundation for understanding some of the effects of polyatomic bombardment. In this paper, we describe simulations of the bombardment of a more realistic model system, an overlayer of sec-butyl-terminated polystyrene tetramers on a Ag left brace 1 1 1 right brace substrate. We have used this model system to study the bombardment with Xe and SF sub 5 projectiles at kinetic energies ranging from 0.50 to 5.0 keV. SF sub 5 sputters more molecules than Xe, but a higher percentage of these are damaged rather than ejected intact when the bombarding energy is greater than 0.50 keV. Therefore, at energies comparable to experimental values, the efficiency, measured as the yield-to-damage ratio, is greater with Xe than SF sub 5. Stable and intact molecules are generally produced by upward moving substrate atoms, while fragments are produced by the upward and lateral motion of reflected projectile atoms and fragments from the target molecul...

Effects of ion beam bombardment of carbon thin films deposited onto tungsten carbide and tool steels

Energy Technology Data Exchange (ETDEWEB)

Awazu, Kaoru; Yoshida, Hiroyuki [Industrial Research Inst. of Ishikawa (Japan); Watanabe, Hiroshi [Gakushuin Univ., Tokyo (Japan); Iwaki, Masaya; Guzman, L [RIKEN, Saitama (Japan)

1992-04-15

A study was made of the effects of argon ion bombardment of carbon thin films deposited onto WC and tool steels. Carbon thin film deposition was performed at various temperatures ranging from 200degC to 350degC, using C{sub 6}H{sub 6} gas. Argon ion beam bombardment of the films was carried out at an energy of 150 keV with a dose of 1x10{sup 16} ions cm{sup -2}. The hardness and adhesion of the films were measured by means of Knoop hardness and scratch tests respectively. The structure of the carbon films was estimated by laser Raman spectroscopy, and the relations were investigated between the mechanical properties and the structure of the films. The hardness of carbon thin films increases as their deposition temperature decreases; this tendency corresponds to the increase in amorphous structure estimated by Raman spectra. Argon ion bombardment results in constant hardness and fraction of amorphous structure. Argon ion beam bombardment of films prior to additional carbon deposition may cause the adhesion of the subsequently deposited films to improve. It is concluded that argon ion beam bombardment is useful for improving the properties of carbon films deposited onto WC and tool steels. (orig.).

Effects of ion beam bombardment of carbon thin films deposited onto tungsten carbide and tool steels

International Nuclear Information System (INIS)

Awazu, Kaoru; Yoshida, Hiroyuki; Watanabe, Hiroshi; Iwaki, Masaya; Guzman, L.

1992-01-01

A study was made of the effects of argon ion bombardment of carbon thin films deposited onto WC and tool steels. Carbon thin film deposition was performed at various temperatures ranging from 200degC to 350degC, using C 6 H 6 gas. Argon ion beam bombardment of the films was carried out at an energy of 150 keV with a dose of 1x10 16 ions cm -2 . The hardness and adhesion of the films were measured by means of Knoop hardness and scratch tests respectively. The structure of the carbon films was estimated by laser Raman spectroscopy, and the relations were investigated between the mechanical properties and the structure of the films. The hardness of carbon thin films increases as their deposition temperature decreases; this tendency corresponds to the increase in amorphous structure estimated by Raman spectra. Argon ion bombardment results in constant hardness and fraction of amorphous structure. Argon ion beam bombardment of films prior to additional carbon deposition may cause the adhesion of the subsequently deposited films to improve. It is concluded that argon ion beam bombardment is useful for improving the properties of carbon films deposited onto WC and tool steels. (orig.)

Alteration of the UV-visible reflectance spectra of H2O ice by ion bombardment

Science.gov (United States)

Sack, N. J.; Boring, J. W.; Johnson, R. E.; Baragiola, R. A.; Shi, M.

1991-01-01

Satellite in the Jovian and Saturnian system exhibit differences in reflectivity between their 'leading' and 'trailing' surfaces which can affect the local vapor pressure. Since these differences are thought to be due to differences in the flux of bombarding magnetospheric ions, the influence of ion impact on the UV-visible reflectance of water ice surfaces (20-90 K) by keV ion bombardment was studied. An observed decrease in reflectance in the UV is attributed to rearrangement processes that affect the physical microstructure and surface 'roughness'. The ratio in reflectance of bombarded to freshly deposited films is compared to the ratio of the reflectance of the leading and trailing hemispheres for Europa and Ganymede.

Direct thermal effects of the Hadean bombardment did not limit early subsurface habitability

Science.gov (United States)

Grimm, R. E.; Marchi, S.

2018-03-01

Intense bombardment is considered characteristic of the Hadean and early Archean eons, yet some detrital zircons indicate that near-surface water was present and thus at least intervals of clement conditions may have existed. We investigate the habitability of the top few kilometers of the subsurface by updating a prior approach to thermal evolution of the crust due to impact heating, using a revised bombardment history, a more accurate thermal model, and treatment of melt sheets from large projectiles (>100 km diameter). We find that subsurface habitable volume grows nearly continuously throughout the Hadean and early Archean (4.5-3.5 Ga) because impact heat is dissipated rapidly compared to the total duration and waning strength of the bombardment. Global sterilization was only achieved using an order of magnitude more projectiles in 1/10 the time. Melt sheets from large projectiles can completely resurface the Earth several times prior to ∼4.2 Ga but at most once since then. Even in the Hadean, melt sheets have little effect on habitability because cooling times are short compared to resurfacing intervals, allowing subsurface biospheres to be locally re-established by groundwater infiltration between major impacts. Therefore the subsurface is always habitable somewhere, and production of global steam or silicate-vapor atmospheres are the only remaining avenues to early surface sterilization by bombardment.

The effects of surface stripping ZnO nanorods with argon bombardment

International Nuclear Information System (INIS)

Barnett, Chris J; Kryvchenkova, Olga; Maffeis, Thierry G G; Cobley, Richard J; Smith, Nathan A; Kelleher, Liam

2015-01-01

ZnO nanorods are used in devices including field effects transistors, piezoelectric transducers, optoelectronics and gas sensors. However, for efficient and reproducible device operation and contact behaviour, surface contaminants must be removed or controlled. Here we use low doses of argon bombardment to remove surface contamination and make reproducible lower resistance contacts. Higher doses strip the surface of the nanorods allowing intrinsic surface measurements through a cross section of the material. Photoluminescence finds that the defect distribution is higher at the near-surface, falling away in to the bulk. Contacts to the n-type defect-rich surface are near-Ohmic, whereas stripping away the surface layers allows more rectifying Schottky contacts to be formed. The ability to select the contact type to ZnO nanorods offers a new way to customize device behaviour. (paper)

Continuum radiation emitted from transition metals under ion bombardment

International Nuclear Information System (INIS)

El Boujlaidi, A.; Kaddouri, A.; Ait El Fqih, M.; Hammoum, K.; Aouchiche, H.

2012-01-01

Optical emission of transition metals has been studied during 5 keV Kr + ions bombardment within and without oxygen atmosphere in the colliding chamber. The observed spectra consist of a series of discrete lines superimposed on a broad continuum. Generally, the emission intensity was influenced by the presence of oxygen giving rise to transient effects as well as to an increase in the line intensity. The behaviours of spectral lines were successfully explained in term of electron-transfer process between the excited sputtered atom and the solid surface. In this work, we have focused our study on the continuous radiation emitted during ion bombardment. The experimental results suggest that the continuum emission depends on the nature of metal and very probably related to its electronic structure. The collective deactivation of 3d-shell electrons appears to play a role in the emission of this radiation. The observed enhancement in the presence of oxygen is probably due to a significant contribution of the oxide molecules. (authors)

The Formation of Jupiter, the Jovian Early Bombardment and the Delivery of Water to the Asteroid Belt: The Case of (4) Vesta

Science.gov (United States)

Turrini, Diego; Svetsov, Vladimir

2014-01-01

The asteroid (4) Vesta, parent body of the Howardite-Eucrite-Diogenite meteorites, is one of the first bodies that formed, mostly from volatile-depleted material, in the Solar System. The Dawn mission recently provided evidence that hydrated material was delivered to Vesta, possibly in a continuous way, over the last 4 Ga, while the study of the eucritic meteorites revealed a few samples that crystallized in presence of water and volatile elements. The formation of Jupiter and probably its migration occurred in the period when eucrites crystallized, and triggered a phase of bombardment that caused icy planetesimals to cross the asteroid belt. In this work, we study the flux of icy planetesimals on Vesta during the Jovian Early Bombardment and, using hydrodynamic simulations, the outcome of their collisions with the asteroid. We explore how the migration of the giant planet would affect the delivery of water and volatile materials to the asteroid and we discuss our results in the context of the geophysical and collisional evolution of Vesta. In particular, we argue that the observational data are best reproduced if the bulk of the impactors was represented by 1–2 km wide planetesimals and if Jupiter underwent a limited (a fraction of au) displacement. PMID:25370027

The Formation of Jupiter, the Jovian Early Bombardment and the Delivery of Water to the Asteroid Belt: The Case of (4 Vesta

Directory of Open Access Journals (Sweden)

Diego Turrini

2014-01-01

Full Text Available The asteroid (4 Vesta, parent body of the Howardite-Eucrite-Diogenite meteorites, is one of the first bodies that formed, mostly from volatile-depleted material, in the Solar System. The Dawn mission recently provided evidence that hydrated material was delivered to Vesta, possibly in a continuous way, over the last 4 Ga, while the study of the eucritic meteorites revealed a few samples that crystallized in presence of water and volatile elements. The formation of Jupiter and probably its migration occurred in the period when eucrites crystallized, and triggered a phase of bombardment that caused icy planetesimals to cross the asteroid belt. In this work, we study the flux of icy planetesimals on Vesta during the Jovian Early Bombardment and, using hydrodynamic simulations, the outcome of their collisions with the asteroid. We explore how the migration of the giant planet would affect the delivery of water and volatile materials to the asteroid and we discuss our results in the context of the geophysical and collisional evolution of Vesta. In particular, we argue that the observational data are best reproduced if the bulk of the impactors was represented by 1–2 km wide planetesimals and if Jupiter underwent a limited (a fraction of au displacement.

The effect of oxygen ion beam bombardment on the properties of tin indium oxide/polyethylene terephthalate complex

International Nuclear Information System (INIS)

Li, Li; Liu, Honglin; Zou, Lin; Ding, Wanyu; Ju, Dongying; Chai, Weiping

2013-01-01

The tin indium oxide (ITO) films were deposited onto the polyethylene terephthalate (PET) surface that has been bombarded by an O ion beam. The variation of the O bombardment time resulted in the production of ITO/PET complex with different properties. Characterization by four-point probe measurement after the bending fatigue test showed that the adhesion property of the ITO/PET complex could be improved by the increase of O bombardment time while little change of electrical resistivity was observed. Scanning electron microscopy results showed that after the bending fatigue test, the nano scale seams and micro scale trenches appeared at the surface of the ITO/PET complex. The former was only the cracks of ITO film, which has little influence on the continuity and electrical resistivity of ITO film. On the contrary, the micro scale trenches were caused by the peeling off of ITO chips at the cracks, which mainly influenced the continuity and electrical resistivity of ITO film. With the increase of O bombardment time, the number and length of the micro scale trenches decreased. X-ray photoelectron spectrometry characterization showed that with the increase of O bombardment time, parts of the methylene C bonds were transformed into C=O bonds, which could be broken to form C-O-In(Sn) bonds at the initial stage of ITO film growth. By these C-O-In(Sn) crosslink bonds, the ITO film could adhere well onto the PET and the ITO/PET complex display better anti-bending fatigue property. Finally, in the context of the application of the ITO/PET complex as a flexible electrode substrate, the present work reveals a simple way to crosslink them, as well as the physicochemical mechanism happening at the interface of complex. - Highlights: • Polyethylene terephthalate (PET) surface was bombarded by N ions. • Tin indium oxide (ITO) film was deposited on bombarded PET surface. • By bombardment, methylene C bond on PET surface was broken and replaced by C=O bond. • C=O bond was

The effect of oxygen ion beam bombardment on the properties of tin indium oxide/polyethylene terephthalate complex

Energy Technology Data Exchange (ETDEWEB)

Li, Li; Liu, Honglin; Zou, Lin [School of Materials Science and Engineering, Dalian Jiaotong University, Dalian 116028 (China); Ding, Wanyu, E-mail: dwysd_2000@163.com [School of Materials Science and Engineering, Dalian Jiaotong University, Dalian 116028 (China); Key Laboratory of Materials Modification by Laser, Ion and Electron Beams (Dalian University of Technology), Ministry of Education, Dalian 116028 (China); Ju, Dongying [Department of Material Science and Engineering, Saitama Institute of Technology, Fukaya 369-0293 (Japan); Chai, Weiping [School of Materials Science and Engineering, Dalian Jiaotong University, Dalian 116028 (China)

2013-10-31

The tin indium oxide (ITO) films were deposited onto the polyethylene terephthalate (PET) surface that has been bombarded by an O ion beam. The variation of the O bombardment time resulted in the production of ITO/PET complex with different properties. Characterization by four-point probe measurement after the bending fatigue test showed that the adhesion property of the ITO/PET complex could be improved by the increase of O bombardment time while little change of electrical resistivity was observed. Scanning electron microscopy results showed that after the bending fatigue test, the nano scale seams and micro scale trenches appeared at the surface of the ITO/PET complex. The former was only the cracks of ITO film, which has little influence on the continuity and electrical resistivity of ITO film. On the contrary, the micro scale trenches were caused by the peeling off of ITO chips at the cracks, which mainly influenced the continuity and electrical resistivity of ITO film. With the increase of O bombardment time, the number and length of the micro scale trenches decreased. X-ray photoelectron spectrometry characterization showed that with the increase of O bombardment time, parts of the methylene C bonds were transformed into C=O bonds, which could be broken to form C-O-In(Sn) bonds at the initial stage of ITO film growth. By these C-O-In(Sn) crosslink bonds, the ITO film could adhere well onto the PET and the ITO/PET complex display better anti-bending fatigue property. Finally, in the context of the application of the ITO/PET complex as a flexible electrode substrate, the present work reveals a simple way to crosslink them, as well as the physicochemical mechanism happening at the interface of complex. - Highlights: • Polyethylene terephthalate (PET) surface was bombarded by N ions. • Tin indium oxide (ITO) film was deposited on bombarded PET surface. • By bombardment, methylene C bond on PET surface was broken and replaced by C=O bond. • C=O bond was

Ion bombardment effect on surface state of metal

International Nuclear Information System (INIS)

Vaulin, E.P.; Georgieva, N.E.; Martynenko, T.P.

1990-01-01

The effect of slow argon ion bombardment on the surface microstructure of polycrystalline copper as well as the effect of surface state on sputtering of D-16 polycrystalline alloy are experimentally studied. Reduction of copper surface roughness is observed. It is shown that the D-16 alloy sputtering coefficient is sensitive to the surface state within the limits of the destructed surface layer

A molecular dynamics study of helium bombardments on tungsten nanoparticles

Science.gov (United States)

Li, Min; Hou, Qing; Cui, Jiechao; Wang, Jun

2018-06-01

Molecular dynamics simulations were conducted to study the bombardment process of a single helium atom on a tungsten nanoparticle. Helium atoms ranging from 50 eV to 50 keV were injected into tungsten nanoparticles with a diameter in the range of 2-12 nm. The retention and reflection of projectiles and sputtering of nanoparticles were calculated at various times. The results were found to be relative to the nanoparticle size and projectile energy. The projectile energy of 100 eV contributes to the largest retention of helium atoms in tungsten nanoparticles. The most obvious difference in reflection exists in the range of 3-10 keV. Around 66% of sputtering atoms is in forward direction for projectiles with incident energy higher than 10 keV. Moreover, the axial direction of the nanoparticles was demonstrated to influence the bombardment to some degree.

Statistical characterization of surface defects created by Ar ion bombardment of crystalline silicon

International Nuclear Information System (INIS)

Ghazisaeidi, M.; Freund, J. B.; Johnson, H. T.

2008-01-01

Ion bombardment of crystalline silicon targets induces pattern formation by the creation of mobile surface species that participate in forming nanometer-scale structures. The formation of these mobile species on a Si(001) surface, caused by sub-keV argon ion bombardment, is investigated through molecular dynamics simulation of Stillinger-Weber [Phys. Rev. B 31, 5262 (1985)] silicon. Specific criteria for identifying and classifying these mobile atoms based on their energy and coordination number are developed. The mobile species are categorized based on these criteria and their average concentrations are calculated

Investigation of /sup 16/O+/sup 27/Al reaction at bombarding energies below 5. 3 MeV/A

Energy Technology Data Exchange (ETDEWEB)

Wen-Qing, Shen; Yong-Tai, Zhu; Wen-Long, Zhan; Zhong-Yan, Guo; Shu-Zhi, Yin; Wei-Min, Qiao; En-Chiu, Wu

1987-03-01

Quasi elastic and deep inelastic collision induced by /sup 16/O+/sup 27/Al at the bombarding energies below 5.3 MeV/A have been studied in detail. Experimental angular energy atomic charge distribution and contour plots of the differential cross sections d/sup 3/sigma/dEd..cap omega..dZ on E-theta plan are presented, their evolution with the bombarding energies are analysed. The competion between quasi elastic and deep inelastic collision as a functon of the bombarding energies has been discussed.

Synthesis of amylose-block-polystyrene rod-coil block copolymers

NARCIS (Netherlands)

Loos, Katja; Stadler, Reimund

1997-01-01

In the present communication we demonstrate the synthesis of a hybrid block copolymer based on the combination of a biopolymer (amylose) with a synthetic block (polystyrene). To obtain such materials, amino-functionalized polymers were modified with maltoheptaose moieties that serve as initiators

Absorption of hydrogen in vanadium, enhanced by ion bombardment; Ionenbeschussunterstuetzte Absorption des Wasserstoffs in Vanadium

Energy Technology Data Exchange (ETDEWEB)

Paulus, H.; Lammers, M. [Inst. fuer Technologie- und Wissenstransfer, Soest (Germany); Mueller, K.H. [Inst. fuer Technologie- und Wissenstransfer, Soest (Germany)]|[Paderborn Univ. (Gesamthochschule), Soest (Germany). Fachbereich 16 - Elektrische Energietechnik; Kiss, G.; Kemeny, Z. [Technical Univ. Budapest (Hungary)

1998-12-31

Prior to hydrogen implantation into vanadium, the vanadium specimen usually is exposed to an activation process and is then heated at 1 atm hydrogen to temperatures between 500 and 600 C, subsequently cooled down in several steps. Within this temperature range, hydrogen solubility increases with declining temperature. A decisive factor determining hydrogen absorption is the fact that at temperatures above 250 C, oxygen desorbs from the material surface and thus no longer inhibits hydrogen absorption. Therefore a different approach was chosen for the experiments reported: Hydrogen absorption under UHV conditions at room temperature. After the usual activation process, the vanadium surface was cleaned by 5 keV Ar{sup +} ion bombardment. Thus oxygen absorption at the specimen surface (and new reactions with oxygen from the remaining gas) could be avoided, or removed. By means of thermal desorption mass spectrometry (TDMS), hydrogen absorption as a function of argon ion dose was analysed. TDMS measurements performed for specimens treated by ion bombardment prior to H{sup 2} exposure showed two H{sup 2} desorption peaks, in contrast to the profiles measured with specimens not exposed to ion bombardment. It is assumed that the ion bombardment disturbs the crystal structure so that further sites for hydrogen absorption are produced. (orig./CB) [Deutsch] Bei der Beladung von Vandium mit Wasserstoff wird ueblicherweise die Probe nach einer Aktivierungsprozedur bei 1 atm Wasserstoff auf Temperaturen im Bereich von 500 bis 600 C hochgeheizt und danach schrittweise abgekuehlt. In diesem Temperaturbereich nimmt die Wasserstoffloeslichkeit mit abnehmender Temperatur zu. Entscheidend fuer die Beladung ist aber auch die Tatsache, dass bei Temperaturen groesser 250 C Sauerstoff von der Oberflaeche desorbiert und dadurch die Absorption von Wasserstoff nicht mehr blockieren kann. Im Rahmen der hier beschriebenen Untersuchungen sollte die Wasserstoffbeladung unter UHV-Bedingungen bei

Stable transformation of the oomycete, Phytophthora infestans, using microprojectile bombardment

DEFF Research Database (Denmark)

Cvitanich, Cristina; Judelson, Howard S.

2003-01-01

Germinated asexual sporangia, zoospores, and mycelia of Phytophthora infestans were transformed to G418-resistance by microprojectile bombardment. After optimization, an average of 14 transformants/shot were obtained, using 10(6) germinated sporangia and gold particles coated with 1 microg...

Damage and redistribution of impurities by ionic bombardment

International Nuclear Information System (INIS)

Tognetti, N.P.

1982-01-01

Some aspects of displacement collisions in solids bombarded with ions in the medium energy range have been studied using the backscattering and channelling techniques. The production of lattice damage and the spatial redistribution of atoms within the collision cascade were the two main effects considered and experimentally studied. A comprehensive study of disorder production in GaAs was carried out at 40 K for a variety of ions and ion energies, providing insight into the mechanisms of damage generation from both the macro and microscopic points of view. Experiments on thermal recovery of partially disordered substrates revealed that annealing occurs from approximately 100 K to 300 K. A direct procedure developed for the obtainment of damage profiles from backscattering-channelling measurements is described. The net spatial redistribution of displaced atoms, in combined impurity-matrix substrates was studied and compared with existing theories of ion beam mixing. The Ag-Si system was studied for a wide range of fluence of bombarding Ar + ions. Furthermore, the contribution of atomic mixing in the experimental observation of Ge implantation at high doses into Si is discussed. (M.E.L) [es

Flaking and blistering on He and Ne bombardments

International Nuclear Information System (INIS)

Kamada, K.; Naramoto, H.

1979-01-01

Large scale exfoliation formed by 300 keV He + bombardment of niobium without any preceding blistering is investigated, in comparison with the blistering due to 450 and 850 keV Ne + bombardments. In-situ observations of the erosion processes were performed in a scanning electron microscope connected to the Van de Graaff. Critical doses of 7.2 x 10 17 He + /cm 2 , 2.4 x 10 17 Ne + /cm 2 and 4.0 x 10 17 Ne + /cm 2 were obtained for the 300 keV He flaking, 450 keV Ne blistering and 850 keV Ne blistering, respectively. The He flaking was presumed to be due to brittle fashion peeling-off of the surface layer by the bending moment driven by the internal gas pressure. The blistering, on the other hand, was presumed to be the result of the ductile fashion spreading of the lenticular bubble in the sub-surface layer. The necessary pressure for the peeling-off of the cover was calculated, and was speculated to be able to work as the driving force for the flaking from its unexpectedly low values. Fractographies under the exfoliations were discussed for both flaking and blistering. (author)

The formation of giant planets and its effects on protoplanetary disks: the case of Jupiter and the Jovian Early Bombardment

Science.gov (United States)

Turrini, D.; ISSI Team "Vesta, the key to the origins of the Solar System"; EChO "Planetary Formation" Working Group

The formation of giant planets is accompanied by a short but intense primordial bombardment \\citep{safronov69,weidenschilling75,weidenschilling01,turrini11}: the prototype for this class of events is the Jovian Early Bombardment (JEB) caused by the formation of Jupiter in the Solar System \\citep{turrini11,turrini12}. The JEB affected the collisional evolution of the minor bodies in the inner Solar System by inflicting mass loss to planetesimals \\citep{turrini12,turrini14a,turrini14b} due to cratering erosion and, at the same time, delivering water and volatile materials to the asteroid belt \\citep{turrini14b}. The JEB also resulted in a significant number of collisions between Jupiter and planetesimals formed over a wide orbital range, delivering volatile and refractory materials to the giant planet and its circumplanetary disk \\citep{turrini14c}. In this talk I'll discuss how the study of the effects of the JEB on Vesta can be used to constrain the early evolution of the Solar System \\citep{turrini14a,turrini14b} and how these constraints can, in turn, provide insight on the composition of Jupiter and of its satellites. Finally, I'll discuss the implications of the JEB model for extrasolar planets \\citep{turrini14c}.

Development of a double plasma gun device for investigation of effects of vapor shielding on erosion of PFC materials under ELM-like pulsed plasma bombardment

Science.gov (United States)

Sakuma, I.; Iwamoto, D.; Kitagawa, Y.; Kikuchi, Y.; Fukumoto, N.; Nagata, M.

2012-10-01

It is considered that thermal transient events such as type I edge localized modes (ELMs) could limit the lifetime of plasma-facing components (PFCs) in ITER. We have investigated surface damage of tungsten (W) materials under transient heat and particle loads by using a magnetized coaxial plasma gun (MCPG) device at University of Hyogo. The capacitor bank energy for the plasma discharge is 144 kJ (2.88 mF, 10 kVmax). Surface melting of a W material was clearly observed at the energy density of ˜2 MJ/m2. It is known that surface melting and evaporation during a transient heat load could generate a vapor cloud layer in front of the target material [1]. Then, the subsequent erosion could be reduced by the vapor shielding effect. In this study, we introduce a new experiment using two MCPG devices (MCPG-1, 2) to understand vapor shielding effects of a W surface under ELM-like pulsed plasma bombardment. The capacitor bank energy of MCPG-2 is almost same as that of MCPG-1. The second plasmoid is applied with a variable delay time after the plasmoid produced by MCPG-1. Then, a vapor cloud layer could shield the second plasma load. To verify the vapor shielding effects, surface damage of a W material is investigated by changing the delay time. In the conference, the preliminary experimental results will be shown.[4pt] [1] A. Hassanein et al., J. Nucl. Mater. 390-391, pp. 777-780 (2009).

On the reasons for bombarding uranium with slow neutrons

International Nuclear Information System (INIS)

Xu Diyu

1997-01-01

Form the concepts of slow neutrons, the binding energy and the excitation energy of complex nuclei, and the activation energy in nuclear fission, the four reasons for bombarding uranium with slow neutrons are summed up. Not only the reasons for uranium fission are brought in light, but also the micromechanism is dealt with

Emission of positive oxygen ions from ion bombardment of adsorbate-covered metal surfaces

International Nuclear Information System (INIS)

Kaurin, M.G.

1989-01-01

During ion bombardment of metal surfaces, collision cascades can result in the emission of sputtered secondary ions. Recent experiments, however, have suggested that the emission of positive ions of electronegative adsorbates can result from electronic processes rather than from processes involving elastic collisions. This dissertation presents the results of experiments studying the emission of positive oxygen ions from oxygen- and carbon-monoxide-covered transition metal surfaces during bombardment by 25-250 keV ions of neon, argon, and krypton. The systems studied may be grouped into four categories. For a nickel substrate with adsorbed oxygen, the emission of positive oxygen ions proceeds through collision cascades. For titanium and niobium with adsorbed oxygen, the emission of positive oxygen ions is proportional to the primary ion velocity, consistent with emission from electronic processes; for a given primary ion velocity, the oxygen ion yield is independent of primary ion species. For substrates of molybdenum and tungsten, the oxygen yield is proportional to primary ion velocity, but the yield also depends on the primary ion species for a given primary ion velocity in a manner that is consistent with emission resulting from electronic processes. For these two groups, except for titanium, the yields during neon ion bombardment do not extrapolate (assuming linearity with primary ion velocity) to a nonzero value at zero beam velocity. The magnitude of the oxygen ion yields from these targets is not consistent with that expected if the emission were induced by secondary electrons emitted during the ion bombardment

Creating Active Device Materials for Nanoelectronics Using Block Copolymer Lithography.

Science.gov (United States)

Cummins, Cian; Bell, Alan P; Morris, Michael A

2017-09-30

The prolonged and aggressive nature of scaling to augment the performance of silicon integrated circuits (ICs) and the technical challenges and costs associated with this has led to the study of alternative materials that can use processing schemes analogous to semiconductor manufacturing. We examine the status of recent efforts to develop active device elements using nontraditional lithography in this article, with a specific focus on block copolymer (BCP) feature patterning. An elegant route is demonstrated using directed self-assembly (DSA) of BCPs for the fabrication of aligned tungsten trioxide (WO₃) nanowires towards nanoelectronic device application. The strategy described avoids conventional lithography practices such as optical patterning as well as repeated etching and deposition protocols and opens up a new approach for device development. Nanoimprint lithography (NIL) silsesquioxane (SSQ)-based trenches were utilized in order to align a cylinder forming poly(styrene)- block -poly(4-vinylpyridine) (PS- b -P4VP) BCP soft template. We outline WO₃ nanowire fabrication using a spin-on process and the symmetric current-voltage characteristics of the resulting Ti/Au (5 nm/45 nm) contacted WO₃ nanowires. The results highlight the simplicity of a solution-based approach that allows creating active device elements and controlling the chemistry of specific self-assembling building blocks. The process enables one to dictate nanoscale chemistry with an unprecedented level of sophistication, forging the way for next-generation nanoelectronic devices. We lastly outline views and future research studies towards improving the current platform to achieve the desired device performance.

Creating Active Device Materials for Nanoelectronics Using Block Copolymer Lithography

Directory of Open Access Journals (Sweden)

Cian Cummins

2017-09-01

Full Text Available The prolonged and aggressive nature of scaling to augment the performance of silicon integrated circuits (ICs and the technical challenges and costs associated with this has led to the study of alternative materials that can use processing schemes analogous to semiconductor manufacturing. We examine the status of recent efforts to develop active device elements using nontraditional lithography in this article, with a specific focus on block copolymer (BCP feature patterning. An elegant route is demonstrated using directed self-assembly (DSA of BCPs for the fabrication of aligned tungsten trioxide (WO3 nanowires towards nanoelectronic device application. The strategy described avoids conventional lithography practices such as optical patterning as well as repeated etching and deposition protocols and opens up a new approach for device development. Nanoimprint lithography (NIL silsesquioxane (SSQ-based trenches were utilized in order to align a cylinder forming poly(styrene-block-poly(4-vinylpyridine (PS-b-P4VP BCP soft template. We outline WO3 nanowire fabrication using a spin-on process and the symmetric current-voltage characteristics of the resulting Ti/Au (5 nm/45 nm contacted WO3 nanowires. The results highlight the simplicity of a solution-based approach that allows creating active device elements and controlling the chemistry of specific self-assembling building blocks. The process enables one to dictate nanoscale chemistry with an unprecedented level of sophistication, forging the way for next-generation nanoelectronic devices. We lastly outline views and future research studies towards improving the current platform to achieve the desired device performance.

3D imaging by serial block face scanning electron microscopy for materials science using ultramicrotomy

Energy Technology Data Exchange (ETDEWEB)

Hashimoto, Teruo, E-mail: t.hashimoto@manchester.ac.uk; Thompson, George E.; Zhou, Xiaorong; Withers, Philip J.

2016-04-15

Mechanical serial block face scanning electron microscopy (SBFSEM) has emerged as a means of obtaining three dimensional (3D) electron images over volumes much larger than possible by focused ion beam (FIB) serial sectioning and at higher spatial resolution than achievable with conventional X-ray computed tomography (CT). Such high resolution 3D electron images can be employed for precisely determining the shape, volume fraction, distribution and connectivity of important microstructural features. While soft (fixed or frozen) biological samples are particularly well suited for nanoscale sectioning using an ultramicrotome, the technique can also produce excellent 3D images at electron microscope resolution in a time and resource-efficient manner for engineering materials. Currently, a lack of appreciation of the capabilities of ultramicrotomy and the operational challenges associated with minimising artefacts for different materials is limiting its wider application to engineering materials. Consequently, this paper outlines the current state of the art for SBFSEM examining in detail how damage is introduced during slicing and highlighting strategies for minimising such damage. A particular focus of the study is the acquisition of 3D images for a variety of metallic and coated systems. - Highlights: • The roughness of the ultramicrotomed block face of AA2024 in Al area was 1.2 nm. • Surface texture associated with chattering was evident in grains with 45° diamond knife. • A 76° rake angle minimises the stress on the block face. • Using the oscillating knife with a cutting speed of 0.04 mms{sup −1} minimised the surface texture. • A variety of material applications were presented.

Surface damage studies of ETFE polymer bombarded with low energy Si ions (≤100 keV)

International Nuclear Information System (INIS)

Minamisawa, Renato Amaral; Almeida, Adelaide De; Budak, Satilmis; Abidzina, Volha; Ila, Daryush

2007-01-01

Surface studies of ethylenetetrafluoroethylene (ETFE), bombarded with Si in a high-energy tandem Pelletron accelerator, have recently been reported. Si ion bombardment with a few MeV to a few hundred keV energies was shown to be sufficient to produce damage on ETFE film. We report here the use of a low energy implanter with Si ion energies lower than 100 keV, to induce changes on ETFE films. In order to determine the radiation damage, ETFE bombarded films were simulated with SRIM software and analyzed with optical absorption photometry (OAP), Raman and Fourier transform infrared-attenuated total reflectance (FTIR-ATR) spectroscopy to show quantitatively the physical and chemical property changes. Carbonization occurs following higher dose implantation, and hydroperoxides were formed following dehydroflorination of the polymer

Actinide production in 136Xe bombardments of 249Cf

International Nuclear Information System (INIS)

Gregorich, K.E.

1985-08-01

The production cross sections for the actinide products from 136 Xe bombardments of 249 Cf at energies 1.02, 1.09, and 1.16 times the Coulomb barrier were determined. Fractions of the individual actinide elements were chemically separated from recoil catcher foils. The production cross sections of the actinide products were determined by measuring the radiations emitted from the nuclides within the chemical fractions. The chemical separation techniques used in this work are described in detail, and a description of the data analysis procedure is included. The actinide production cross section distributions from these 136 Xe + 249 Cf bombardments are compared with the production cross section distributions from other heavy ion bombardments of actinide targets, with emphasis on the comparison with the 136 Xe + 248 Cm reaction. A technique for modeling the final actinide cross section distributions has been developed and is presented. In this model, the initial (before deexcitation) cross section distribution with respect to the separation energy of a dinuclear complex and with respect to the Z of the target-like fragment is given by an empirical procedure. It is then assumed that the N/Z equilibration in the dinuclear complex occurs by the transfer of neutrons between the two participants in the dinuclear complex. The neutrons and the excitation energy are statistically distributed between the two fragments using a simple Fermi gas level density formalism. The resulting target-like fragment initial cross section distribution with respect to Z, N, and excitation energy is then allowed to deexcite by emission of neutrons in competition with fission. The result is a final cross section distribution with respect to Z and N for the actinide products. 68 refs., 33 figs., 6 tabs

Bombardment-induced compositional change with alloys, oxides, and oxysalts. 1

International Nuclear Information System (INIS)

Kelly, R.

1989-01-01

A review of the role of surface binding energies in bombardment-induced compositional change with alloys, oxides and oxysalts is presented. The concepts of preferential sputtering and compositional change may or may not coincide; their differences are clarified. 77 refs.; 12 figs.; 4 tabs

Proposals for the heating mechanism of an electron-bombarded body

International Nuclear Information System (INIS)

Geller, R.; Yerouchalmi, F.

1967-01-01

When a thermally isolated target in vacuum is bombarded by an electron beam the target becomes red. In this paper we try a heuristic explanation indicating how the kinetic power of the beam may be transformed into radiation power controlled by Stefan law. (authors) [fr

Three-Dimensionally Isotropic Negative Refractive Index Materials from Block Copolymer Self-Assembled Chiral Gyroid Networks

KAUST Repository

Hur, Kahyun

2011-10-17

Metamaterials are engineered artificial materials that offer new functionalities such as super-resolution imaging and cloaking. Calculations of the photonic properties of three-dimensionally isotropic metamaterials with cubic double gyroid and alternating gyroid morphologies from block copolymer self-assembly are presented.

Stepwise transformation of the molecular building blocks in a porphyrin-encapsulating metal-organic material

KAUST Repository

Zhang, ZhenJie; Wojtas, Łukasz; Eddaoudi, Mohamed; Zaworotko, Michael J.

2013-01-01

When immersed in solutions containing Cu(II) cations, the microporous metal-organic material P11 ([Cd4(BPT)4]·[Cd(C 44H36N8)(S)]·[S], BPT = biphenyl-3,4′,5-tricarboxylate) undergoes a transformation of its [Cd 2(COO)6]2- molecular building blocks

Effects of low-energy ion beam bombardment on metal oxides

International Nuclear Information System (INIS)

Sullivan, J.L.; Saied, S.O.; Choudhury, T.

1993-01-01

This paper describes a study of Ar ion bombardment damage in metal oxides. In the energy range 1 to 5 keV, preferential oxygen removal and reduction of the oxides was found to depend on ion current density, but to be independent of beam energy. (author)

Low-energy ion beam bombardment effect on the plant-cell-envelope mimetic membrane for DNA transfer

International Nuclear Information System (INIS)

Prakrajang, K.; Sangwijit, K.; Anuntalabhochai, S.; Wanichapichart, P.; Yu, L.D.

2012-01-01

This study is a systematic analysis of the mechanisms involved in ion-beam induced DNA transfer, an important application of ion beam biotechnology. Cellulose membranes were used to mimic the plant cell envelope. Ion beams of argon (Ar) or nitrogen (N) at an energy of 25 keV bombarded the cellulose membranes at fluences ranging from 10 15 to 10 16 ions/cm 2 . The damage to the ion-beam-bombarded membranes was characterized using infrared spectroscopy, a micro tensile test and scanning electron microscopy (SEM). Chain scission was the dominant radiation damage type in the membrane. DNA diffusion across the membrane was significantly increased after ion beam bombardment. The increase in DNA transfer is therefore attributed to chain scission, which increases the permeability by increasing the number of pores in the membrane.

Nucleic acids and smart materials: advanced building blocks for logic systems.

Science.gov (United States)

Pu, Fang; Ren, Jinsong; Qu, Xiaogang

2014-09-03

Logic gates can convert input signals into a defined output signal, which is the fundamental basis of computing. Inspired by molecular switching from one state to another under an external stimulus, molecular logic gates are explored extensively and recognized as an alternative to traditional silicon-based computing. Among various building blocks of molecular logic gates, nucleic acid attracts special attention owing to its specific recognition abilities and structural features. Functional materials with unique physical and chemical properties offer significant advantages and are used in many fields. The integration of nucleic acids and functional materials is expected to bring about several new phenomena. In this Progress Report, recent progress in the construction of logic gates by combining the properties of a range of smart materials with nucleic acids is introduced. According to the structural characteristics and composition, functional materials are categorized into three classes: polymers, noble-metal nanomaterials, and inorganic nanomaterials. Furthermore, the unsolved problems and future challenges in the construction of logic gates are discussed. It is hoped that broader interests in introducing new smart materials into the field are inspired and tangible applications for these constructs are found. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Using the Geminids to Characterize the Surface Response of an Airless Body to Meteoroid Bombardment

Science.gov (United States)

Szalay, J.; Pokorny, P.; Jenniskens, P. M. M.; Horanyi, M.

2017-12-01

All airless bodies in the solar system are exposed to the continual bombardment by interplanetary meteoroids. These impacts can eject orders of magnitude more mass than the primary impactors, sustaining bound and/or unbound ejecta clouds that vary both spatially and temporally from changes in impactor fluxes. The dust environment in the vicinity of an airless body provides both a scientific resource and a hazard for exploration. Characterizing the spatial and temporal variability of the dust environment of airless planetary bodies provides a novel way to understand their meteoroid environment by effectively using these objects as large surface area meteoroid detectors. Additionally, were a dust detector with chemical sensing capability to be flown near such a body, it would be able to directly measure the composition of the body without requiring the mission design complexity involved in landing and sampling surface material. Paramount to understanding the current and future impact ejecta measurements is a sufficient understanding of the impact ejecta processes at the surface. In this presentation, we focus on data taken by the Lunar Dust Experiment (LDEX), an impact ionization dust detector onboard the Lunar Atmosphere and Dust Environment Explorer (LADEE) mission, designed to measure impact ejecta around the Moon. We use the Geminids meteoroid shower as a well constrained input function, and via comparison to existing ground-based measurements of this shower, to "calibrate" the response of the lunar surface to meteoroid bombardment. Understanding the response of the lunar surface to meteoroid bombardment can by extension allow us to better understand the ejecta response at other regolith airless bodies in the solar system. Future missions equipped with dust detectors sent to the Moon, large Near Earth Asteroids, the Martian moons Phobos and Deimos, or many other airless bodies in the solar system would greatly improve our knowledge of their local meteoroid

Peculiarities of phase transformations in molybdenum-silicon system under ion bombardment

International Nuclear Information System (INIS)

Gurskij, L.I.; Zelenin, V.A.; Bobchenok, Yu.L.

1984-01-01

The problems of effect of ion bombardment and thermal treatment on the mechanisms of formation of transition layers and structural transformations in the molybdenum-silicon system, where the interface is subjected to ion bombardment through a film of molybdenum, are considered. The method of electron diffraction analysis has been applied to establish that at the molybdenum-silicon interface a transitional region appears during irradiation which has a semiamorphous structure at the doses up to 8x10 14 ion/cm 2 , while at higher doses it transforms into polycrystalline intermediate layer which consists of MoB and the compound close in composition to MoSisub(0.65). Due to thermal treatment for 60873 K a large-grain phase (Mo 3 Si+MoSi 2 ) appears in the transition layer below which a large-grain silicon layer is placed

Erosion of Be and deposition of C and O due to bombardment with C{sup +} and CO{sup +}

Energy Technology Data Exchange (ETDEWEB)

Eckstein, W.; Goldstrass, P.; Linsmeier, Ch. [Max-Planck-Institut fuer Plasmaphysik, Garching (Germany)

1998-01-01

The bombardment of Be with 3 and 5 keV C{sup +} and CO{sup +} at normal incidence is investigated experimentally and by computer simulation with the program TRIDYN. The deposited amount of C and O is determined experimentally and found in good agreement with calculated data for C bombardment. Chemical erosion dominates at higher fluences for CO{sup +} bombardment. Calculations are then used to determine the sputter yield of Be at steady state conditions as a function of the plasma edge electron temperature for two C impurity concentrations in the incident D flux, typical for fusion plasmas. The fluence to reach steady state conditions is also investigated. (author)

Electron emission from Inconel under ion bombardment

International Nuclear Information System (INIS)

Alonso, E.V.; Baragiola, R.A.; Ferron, J.; Oliva-Florio, A.

1979-01-01

Electron yields from clean and oxidized Inconel 625 surfaces have been measured for H + ,H 2 + ,He + ,O + and Ar + ions at normal incidence in the energy range 1.5 to 40 keV. These measurements have been made under ultrahigh vacuum and the samples were freed of surface contaminants by bombarding with high doses of either 20 keV H 2 + or 30 keV Ar + ions. Differences in yields of oxidized versus clean surfaces are explained in terms of differences in the probability that electrons internally excited escape upon reaching the surface. (author)

Molecular projectile effects for kinetic electron emission from carbon- and metal-surfaces bombarded by slow hydrogen ions

Science.gov (United States)

Cernusca, S.; Winter, HP.; Aumayr, F.; Díez Muiño, R.; Juaristi, J. I.

2003-04-01

Total yields for kinetic electron emission (KE) have been determined for impact of hydrogen monomer-, dimer- and trimer-ions (impact energy armour in magnetic fusion devices. The data are compared with KE yields for impact of same projectile ions on atomically clean highly oriented pyrolytic graphite and polycrystalline gold. We discuss KE yields for the different targets if bombarded by equally fast molecular and atomic ions in view to "projectile molecular effects" (different yields per proton for equally fast atomic and molecular ions), which are expected from calculated electronic projectile energy losses in these target materials.

Low-energy ion beam bombardment effect on the plant-cell-envelope mimetic membrane for DNA transfer

Energy Technology Data Exchange (ETDEWEB)

Prakrajang, K., E-mail: k.prakrajang@gmail.com [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Sangwijit, K.; Anuntalabhochai, S. [Molecular Biology Laboratory, Department of Biology, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Wanichapichart, P. [Membrane Science and Technology Research Center, Department of Physics, Faculty of Science, Prince of Songkla University, Hat Yai, Songkla 90112 (Thailand); Yu, L.D., E-mail: yuld@fnrf.science.cmu.ac.th [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand)

2012-09-01

This study is a systematic analysis of the mechanisms involved in ion-beam induced DNA transfer, an important application of ion beam biotechnology. Cellulose membranes were used to mimic the plant cell envelope. Ion beams of argon (Ar) or nitrogen (N) at an energy of 25 keV bombarded the cellulose membranes at fluences ranging from 10{sup 15} to 10{sup 16} ions/cm{sup 2}. The damage to the ion-beam-bombarded membranes was characterized using infrared spectroscopy, a micro tensile test and scanning electron microscopy (SEM). Chain scission was the dominant radiation damage type in the membrane. DNA diffusion across the membrane was significantly increased after ion beam bombardment. The increase in DNA transfer is therefore attributed to chain scission, which increases the permeability by increasing the number of pores in the membrane.

Materials research in AECL, Spring 1970

Energy Technology Data Exchange (ETDEWEB)

NONE

1970-05-15

This report gives a summary of materials research at Atomic Energy of Canada Limited. The topics covered in this report include engineering design with brittle materials, texture and mechanical properties of zirconium alloy tubing, structural damage by ion bombardment, research on silicon carbide, shallow phosphorus diffusion in p-type silicon and scanning electron microscopy. CRNL facilities for the examination of irradiated materials is also discussed.

Materials research in AECL, Spring 1970

International Nuclear Information System (INIS)

1970-05-01

This report gives a summary of materials research at Atomic Energy of Canada Limited. The topics covered in this report include engineering design with brittle materials, texture and mechanical properties of zirconium alloy tubing, structural damage by ion bombardment, research on silicon carbide, shallow phosphorus diffusion in p-type silicon and scanning electron microscopy. CRNL facilities for the examination of irradiated materials is also discussed

RBS and NRA damage analysis on PFA films bombarded with hydrogen

International Nuclear Information System (INIS)

Parada, Marco A.; Petchevist, Paulo C.D.; Minamisawa, Renato A.; Almeida, Adelaide de; Muntele, Claudiu I.; Zimmerman, Robert L.; Ila, Daryush

2005-01-01

The fluoropolymer PFA (Tetrafluoroethylene-per-fluoromethoxy ethylene) is a conventional thermoplastic used in civil engineering applications such as anti-adherent coatings and concrete additives. It is also candidate materials for radiation dosimetry with applications in medical physics. When such a polymer is exposed to ionizing radiation, it can suffers damages that depend on the type, energy, and intensity of the radiation. We present results on the damage caused by 1 MeV protons at fluences of 10 13 , 10 14 , 10 15 , and 10 16 protons/cm 2 . The energy deposited during such hydrogen bombardment breaks the polymeric chains with the release of fluorine in amounts directly proportional to the amount of deposited energy. Virgin samples were first analyzed by RBS. Subsequent damage was then profiled by monitoring the alpha emission spectrum, resulting from the nuclear reaction: 19 F(p,αγ) 16 O induced by 1.38 MeV protons on the remaining fluorine content of damaged polymer samples. (author)

Fast atom bombardment mass spectrometry of condensed tannin sulfonate derivatives

Science.gov (United States)

J.J. Karchesy; L.Y. Foo; Richard W. Hemingway; E. Barofsky; D.F. Barofsky

1989-01-01

Condensed tannin sulfonate derivatives were studied by fast atom bombardment mass spectrometry (FAB-MS) to assess the feasibility of using this technique for determining molecular weight and structural information about these compounds. Both positive- and negative-ion spectra provided useful data with regard to molecular weight, cation species present, and presence of...

Dependence of secondary electron emission on the incident angle and the energy of primary electrons bombarding bowl-structured beryllium surfaces

International Nuclear Information System (INIS)

Kawata, Jun; Ohya, Kaoru.

1994-01-01

A Monte Carlo simulation of the secondary electron emission from beryllium is combined with a model of bowl structure for surface roughness, for analyzing the difference between the electron emissions for normal and oblique incidences. At normal incidence, with increasing the roughness parameter H/W, the primary energy E pm at which the maximum electron yield occurs becomes higher, and at more than the E pm , the decrease in the yield is slower; where H and W are the depth and width of the bowl structure, respectively. The dispersion of incident angle to the microscopic surface causes a small increase in the yield at oblique incidence, whereas the blocking of primary electrons from bombarding the bottom of the structure causes an opposite trend. The strong anisotropy in the polar angular distribution with respect to the azimuthal angle is calculated at oblique incidence. (author)

Particle bombardment and the genetic enhancement of crops: myths and realities

NARCIS (Netherlands)

Altpeter, F.; Baisakh, N.; Beachy, R.; Bock, R.; Capell, T.; Christou, P.; Daniell, H.; Datta, K.; Datta, S.; Dix, P.J.; Fauquet, C.; Huang, N.; Kohli, A.; Mooibroek, H.; Nicholson, L.; Nguyen, T.T.; Nugent, G.; Raemakers, C.J.J.M.; Romano, A.; Somers, D.A.; Stoger, E.; Taylor, N.; Visser, R.G.F.

2005-01-01

DNA transfer by particle bombardment makes use of physical processes to achieve the transformation of crop plants. There is no dependence on bacteria, so the limitations inherent in organisms such as Agrobacterium tumefaciens do not apply. The absence of biological constraints, at least until DNA

Ion bombardment induced surface topography modification of clean and contaminated single crystal Cu and Si

International Nuclear Information System (INIS)

Lewis, G.W.; Kiriakides, G.; Carter, G.; Nobes, M.J.

1982-01-01

Among the several factors which lead to depth resolution deterioration during sputter profiling, surface morphological modification resulting from local differences of sputtering rate can be important. This paper reports the results of direct scanning, electron microscopic studies obtained quasi-dynamically during increasing fluence ion bombardment of the evolution of etch pit structures on Si and Cu, and how such elaboration may be suppressed. It also reports on the elaboration of contaminant-induced cone generation for different ion species bombardment. The influence of such etch pit and cone generation on achievable depth resolution is assessed. (author)

Determining the Mechanical Properties of Lattice Block Structures

Science.gov (United States)

Wilmoth, Nathan

2013-01-01

Lattice block structures and shape memory alloys possess several traits ideal for solving intriguing new engineering problems in industries such as aerospace, military, and transportation. Recent testing at the NASA Glenn Research Center has investigated the material properties of lattice block structures cast from a conventional aerospace titanium alloy as well as lattice block structures cast from nickel-titanium shape memory alloy. The lattice block structures for both materials were sectioned into smaller subelements for tension and compression testing. The results from the cast conventional titanium material showed that the expected mechanical properties were maintained. The shape memory alloy material was found to be extremely brittle from the casting process and only compression testing was completed. Future shape memory alloy lattice block structures will utilize an adjusted material composition that will provide a better quality casting. The testing effort resulted in baseline mechanical property data from the conventional titanium material for comparison to shape memory alloy materials once suitable castings are available.

High resistivity in InP by helium bombardment

International Nuclear Information System (INIS)

Focht, M.W.; Macrander, A.T.; Schwartz, B.; Feldman, L.C.

1984-01-01

Helium implants over a fluence range from 10 11 to 10 16 ions/cm 2 , reproducibly form high resistivity regions in both p- and n-type InP. Average resistivities of greater than 10 9 Ω cm for p-type InP and of 10 3 Ω cm for n-type InP are reported. Results are presented of a Monte Carlo simulation of helium bombardment into the compound target InP that yields the mean projected range and the range straggling

Target bombardment by ion beams generated in the Focus experiment

International Nuclear Information System (INIS)

Bernard, Alain; Coudeville, Alain; Garconnet, J.-P.; Jolas, A.; Mascureau, J. de; Nazet, Christian.

1976-01-01

In a Mather-Focus experiment, it was shown that 80% of the neutron emitted were generated through bombardment. The apparatus was operated with various targets at a distance of 13mm from the anode. In the low pressure regime, a deuteron beam of high energy was produced. Its emission duration was measured using a CD 2 target [fr

Low energy Ar ion bombardment damage of Si, GaAs, and InP surfaces

International Nuclear Information System (INIS)

Williams, R.S.

1982-01-01

Argon bombardment damage to (100) surfaces of Si, GaAs, and InP for sputter ion-gun potentials of 1, 2, and 3 kilovolts was studied using Rutherford backscattering. Initial damage rates and saturation damage levels were determined. Bombardment damage sensitivity increased for the sequence Si, GaAs, and InP. Saturation damage levels for Si and GaAs correspond reasonably to LSS projected range plus standard deviation estimates; damage to InP exceeded this level significantly. For an ion-gun potential of 3 keV, the initial sputter yield of P from an InP surface exceeded the sputter yield of In by four atoms per incident Ar projectile. (author)

The development of cones and associated features on ion bombarded copper

International Nuclear Information System (INIS)

Whitton, J.L.; Carter, G.; Nobes, M.J.; Williams, J.S.

1977-01-01

Observations of ion-bombardment-induced surface modifications on crystalline copper substrates have been made using scanning electron microscopy. The delineation and development of grain boundary edges, faceted and terraced etch pits and small-scale ripple structure, together with the formation of faceted conical features, have all been observed on low and high purity polycrystalline substrates. In general, the density of such surface morphological features, although variable from grain to grain, is higher in the proximity of grain boundaries. In particular, cones are only found within regions where other surface erosional features are present and it would appear that the development of these other features is a pre-requisite to cone generation in high-purity crystalline substrates. We suggest the operation of a defect-induced mechanism of cone formation whereby sputter elaboration of bulk defects (either pre-existing or bombardment-induced) leads to the formation and development of surface features which, in turn, may intersect and result in the generation of cones. (author)

The development of cones and associated features on ion bombarded copper

International Nuclear Information System (INIS)

Whitton, J.L.; Williams, J.S.

1977-01-01

Observations of ion-bombardment-induced surface modifications on crystalline copper substrates have been made using scanning electron microscopy. The delineation and development of grain boundary edges, faceted and terraced etch pits and small-scale ripple structure, together with the formation of faceted conical features have all been observed on low and high purity polycrystalline substrates. In general, the density of such surface morphological features, although variable from grain to grain, is higher in the proximity of grain boundaries. In particular, cones are only found within regions where other surface erosional features are present and it would appear that the development of these other surface features is a pre-requisite to cone generation in high-purity crystalline substrates. The authors suggest the operation of a defect-induced mechanism of cone formation whereby sputter elaboration of bulk defects (either preexisting or bombardment-induced) leads to the formation and development of surface features which, in turn, may intersect and result in the generation of cones. (Auth.)

Genetic Transformation of Metroxylon sagu (Rottb.) Cultures via Agrobacterium-Mediated and Particle Bombardment

Science.gov (United States)

Ibrahim, Evra Raunie

2014-01-01

Sago palm (Metroxylon sagu) is a perennial plant native to Southeast Asia and exploited mainly for the starch content in its trunk. Genetic improvement of sago palm is extremely slow when compared to other annual starch crops. Urgent attention is needed to improve the sago palm planting material and can be achieved through nonconventional methods. We have previously developed a tissue culture method for sago palm, which is used to provide the planting materials and to develop a genetic transformation procedure. Here, we report the genetic transformation of sago embryonic callus derived from suspension culture using Agrobacterium tumefaciens and gene gun systems. The transformed embryoids cells were selected against Basta (concentration 10 to 30 mg/L). Evidence of foreign genes integration and function of the bar and gus genes were verified via gene specific PCR amplification, gus staining, and dot blot analysis. This study showed that the embryogenic callus was the most suitable material for transformation as compared to the fine callus, embryoid stage, and initiated shoots. The gene gun transformation showed higher transformation efficiency than the ones transformed using Agrobacterium when targets were bombarded once or twice using 280 psi of helium pressure at 6 to 8 cm distance. PMID:25295258

Genetic Transformation of Metroxylon sagu (Rottb. Cultures via Agrobacterium-Mediated and Particle Bombardment

Directory of Open Access Journals (Sweden)

Evra Raunie Ibrahim

2014-01-01

Full Text Available Sago palm (Metroxylon sagu is a perennial plant native to Southeast Asia and exploited mainly for the starch content in its trunk. Genetic improvement of sago palm is extremely slow when compared to other annual starch crops. Urgent attention is needed to improve the sago palm planting material and can be achieved through nonconventional methods. We have previously developed a tissue culture method for sago palm, which is used to provide the planting materials and to develop a genetic transformation procedure. Here, we report the genetic transformation of sago embryonic callus derived from suspension culture using Agrobacterium tumefaciens and gene gun systems. The transformed embryoids cells were selected against Basta (concentration 10 to 30 mg/L. Evidence of foreign genes integration and function of the bar and gus genes were verified via gene specific PCR amplification, gus staining, and dot blot analysis. This study showed that the embryogenic callus was the most suitable material for transformation as compared to the fine callus, embryoid stage, and initiated shoots. The gene gun transformation showed higher transformation efficiency than the ones transformed using Agrobacterium when targets were bombarded once or twice using 280 psi of helium pressure at 6 to 8 cm distance.

Influence of ion bombardment induced patterning of exchange bias in pinned artificial ferrimagnets on the interlayer exchange coupling

Energy Technology Data Exchange (ETDEWEB)

Schmalhorst, Jan; Reiss, Guenter; Hoenik, V. [Thin Films and Nanostructures, Department of Physics, Univ. Bielefeld (Germany); Weis, Tanja; Engel, Dieter; Ehresmann, Arno [Institute of Physics and Center for Interdisciplinary Nanostructure Science and Technology, Kassel Univ. (Germany)

2007-07-01

Artificial ferrimagnets (AFi) have many applications as, e.g., pinned reference electrodes in magnetic tunnel junctions. It is known that the application of ion bombardment induced magnetic patterning with He ions on a single layer reference electrode of magnetic tunnel junctions is possible. For some applications a combination of ion bombardment induced magnetic patterning and artificial ferrimagnets as a reference electrode is desirable. The effect of ion bombardment induced magnetic patterning on pinned artificial ferrimagnets with a Ru interlayer which is frequently used in magnetic tunnel junctions as well as pinned AFis with a Cu interlayer has been tested. Special attention has been given to the question whether the antiferromagnetic interlayer exchange coupling can withstand the ion dose necessary to turn the exchange bias.

Fusion reactor materials

International Nuclear Information System (INIS)

Anon.

1977-01-01

Data are given for each of the following areas: (1) depth distribution of bubbles in 20-keV 4 He + irradiated nickel, (2) surface damage of Al irradiated with 4 He + to high doses, (3) secondary photon emission from ion bombarded surfaces, (4) dosimetry and damage analysis work in support of the MFE materials program, (5) hydrogen permeation and materials behavior in alloys, (6) radiation damage of diagnostic windows in TFTR, and (7) fast neutron irradiations of superconducting Nb 3 Sn

Ion bombardment induced smoothing of amorphous metallic surfaces: Experiments versus computer simulations

International Nuclear Information System (INIS)

Vauth, Sebastian; Mayr, S. G.

2008-01-01

Smoothing of rough amorphous metallic surfaces by bombardment with heavy ions in the low keV regime is investigated by a combined experimental-simulational study. Vapor deposited rough amorphous Zr 65 Al 7.5 Cu 27.5 films are the basis for systematic in situ scanning tunneling microscopy measurements on the smoothing reaction due to 3 keV Kr + ion bombardment. The experimental results are directly compared to the predictions of a multiscale simulation approach, which incorporates stochastic rate equations of the Langevin type in combination with previously reported classical molecular dynamics simulations [Phys. Rev. B 75, 224107 (2007)] to model surface smoothing across length and time scales. The combined approach of experiments and simulations clearly corroborates a key role of ion induced viscous flow and ballistic effects in low keV heavy ion induced smoothing of amorphous metallic surfaces at ambient temperatures

Composition and structure of ion-bombardment-induced growth cones on InP

International Nuclear Information System (INIS)

Malherbe, J.B.; Lakner, H.; Gries, W.H.

1991-01-01

The previously reported effect of low-energy (several keV) ion bombardment on the surface topography of InP was investigated by scanning transmission electron microscopy. Convergent beam electron diffraction patterns of the surface growth 'cones' induced by argon ion bombardment of (100) InP between 7 and 10 keV proved the cones to consist of crystalline InP (and not metallic indium, as has sometimes been claimed). The investigation showed that the irradiated surface region is not rendered completely amorphous but that it recrystallizes from the crystalline/amorphous interface in a columnar growth pattern, often terminating in growth cones protruding above the surface. Weak beam investigations revealed that the overwhelming majority of the cones have the orientation of the substrate. These phenomena were observed at all dose densities from 7 x 10 15 to 2 x 10 17 cm -2 . (author)

A process for doping an amorphous semiconductor material by ion implantation

International Nuclear Information System (INIS)

Kalbitzer, S.; Muller, G.; Spear, W.E.; Le Comber, P.G.

1979-01-01

In a process for doping a body of amorphous semiconductor material, the body is held at a predetermined temperature above 20 deg. C which is below the recrystallization temperature of the amorphous semiconductor material during bombardment by accelerated ions of a predetermined doping material. (U.K.)

Ion bombardment effects on the fatigue life of stainless steel under simulated fusion first wall conditions

International Nuclear Information System (INIS)

Kohse, G.; Harling, O.K.

1983-01-01

Pressurized tube specimens have been exposed to simultaneous multi-energy surface ion bombardment, fast neutron irradiation and stress and temperature cycling, in a simulation of a possible fusion reactor first wall environment. After ion bombardments equivalent to months-years of reactor operation and up to 30,000 cycles, no detrimental effects on post-irradiation fatigue life were found. The ion damage is found to enhance surface cracking, but this effect is limited to the several micron surface layer in which the ions are implanted

The terrestrial record of Late Heavy Bombardment

Science.gov (United States)

Lowe, Donald R.; Byerly, Gary R.

2018-04-01

Until recently, the known impact record of the early Solar System lay exclusively on the surfaces of the Moon, Mars, and other bodies where it has not been erased by later weathering, erosion, impact gardening, and/or tectonism. Study of the cratered surfaces of these bodies led to the concept of the Late Heavy Bombardment (LHB), an interval from about 4.1 to 3.8 billion years ago (Ga) during which the surfaces of the planets and moons in the inner Solar System were subject to unusually high rates of bombardment followed by a decline to present low impact rates by about 3.5 Ga. Over the past 30 years, however, it has become apparent that there is a terrestrial record of large impacts from at least 3.47 to 3.22 Ga and from 2.63 to 2.49 Ga. The present paper explores the earlier of these impact records, providing details about the nature of the 8 known ejecta layers that constitute the evidence for large terrestrial impacts during the earlier of these intervals, the inferred size of the impactors, and the potential effects of these impacts on crustal development and life. The existence of this record implies that LHB did not end abruptly at 3.8-3.7 Ga but rather that high impact rates, either continuous or as impact clusters, persisted until at least the close of the Archean at 2.5 Ga. It implies that the shift from external, impact-related controls on the long-term development of the surface system on the Earth to more internal, geodynamic controls may have occurred much later in geologic history than has been supposed previously.

Universality of spectator fragmentation at relativistic bombarding energies

International Nuclear Information System (INIS)

Schuettauf, A.; Woerner, A.

1996-06-01

Multi-fragment decays of 129 Xe, 197 Au, and 238 U projectiles in collisions with Be, C, Al, Cu, In, Au, and U targets at energies between E/A=400 MeV and 1000 MeV have been studied with the ALADIN forward-spectrometer at SIS. By adding an array of 84 Si-CsI(Tl) telescopes the solid-angle coverage of the setup was extended to θ lab =16 . This permitted the complete detection of fragments from the projectile-spectator source. The dominant feature of the systematic set of data is the Z bound universality that is obeyed by the fragment multiplicities and correlations. These observables are invariant with respect to the entrance channel if plotted as a function of Z bound , where Z bound is the sum of the atomic numbers Z i of all projectile fragments with Z i ≥2. No significant dependence on the bombarding energy nor on the target mass is observed. The dependence of the fragment multiplicity on the projectile mass follows a linear scaling law. The reasons for and the limits of the observed universality of spectator fragmentation are explored within the realm of the available data and with model studies. It is found that the universal properties should persist up to much higher bombarding energies than explored in this work and that they are consistent with universal features exhibited by the intranuclear cascade and statistical multifragmentation models. (orig.)

Uniaxial backfill block compaction

International Nuclear Information System (INIS)

Koskinen, V.

2012-05-01

The main parts of the project were: to make a literature survey of the previous uniaxial compaction experiments; do uniaxial compaction tests in laboratory scale; and do industrial scale production tests. Object of the project was to sort out the different factors affecting the quality assurance chain of the backfill block uniaxial production and solve a material sticking to mould problem which appeared during manufacturing the blocks of bentonite and cruched rock mixture. The effect of mineralogical and chemical composition on the long term functionality of the backfill was excluded from the project. However, the used smectite-rich clays have been tested for mineralogical consistency. These tests were done in B and Tech OY according their SOPs. The objective of the Laboratory scale tests was to find right material- and compaction parameters for the industrial scale tests. Direct comparison between the laboratory scale tests and industrial scale tests is not possible because the mould geometry and compaction speed has a big influence for the compaction process. For this reason the selected material parameters were also affected by the previous compaction experiments. The industrial scale tests were done in summer of 2010 in southern Sweden. Blocks were done with uniaxial compaction. A 40 tons of the mixture of bentonite and crushed rock blocks and almost 50 tons of Friedland-clay blocks were compacted. (orig.)

Study on the growth of aligned carbon nanotubes controlled by ion bombardment

International Nuclear Information System (INIS)

Wang Biben; Zhang Bing; Zheng Kun; Hao Wei; Wang Wanlu; Liao Kejun

2004-01-01

Aligned carbon nanotubes were prepared by plasma-enhanced hot filament chemical vapor deposition using CH 4 , H 2 and NH 3 as reaction gases. It was investigated how different negative bias affects the growth of aligned carbon nanotubes. The results indicate that the average diameter of the aligned carbon nanotubes is reduced and the average length of the aligned carbon nanotubes is increased with increasing negative bias. Because of the occurrence of glow discharge, a cathode sheath forms near the substrate surface, and a number of ions are produced in it, and a very strong electrical field builds up near the substrate surface. Under the effect of the field, the strong bombardment of ions on the substrate surface will influence the growth of aligned carbon nanotubes. Combined with related theories, authors have analyzed and discussed the ion bombardment effects on the growth of the aligned carbon nanotudes

Chemical changes in titanate surfaces induced by Ar+ ion bombardment

International Nuclear Information System (INIS)

Gonzalez-Elipe, A.R.; Fernandez, A.; Espinos, J.P.; Munuera, G.; Sanz, J.M.

1992-01-01

The reduction effects and compositional changes induced by 3.5 keV Ar + bombardment of several titanates (i.e. SrTiO 3 , Al 2 TiO 5 and NiTiO 3 ) have been quantitatively investigated by XPS. In all the samples studied here the original Ti 4+ species were reduced to lower oxidation states (i.e. Ti 3+ and Ti 2+ ), although to a lesser extent than in pure TiO 2 . On the contrary, whereas Sr 2+ and Al 3+ seem to remain unaffected by Ar + bombardment, in agreement with the behaviour of the respective oxides (i.e. SrO and Al 2 O 3 ), Ni 2+ appears more easily reducible to Ni o in NiTiO 3 than in NiO. In addition, other specific differences were observed between the titanates, which reveal the existence of interesting chemical effects related to the presence of the different counter-ions in the titanates. In the case of Al 2 TiO 5 , its Ar + -induced decomposition to form TiO 2 + Al 2 O 3 could be followed by XPS. (Author)

Considerations about projectile and target X-rays induced during heavy ion bombardment

Science.gov (United States)

Fernandes, F.; Bauer, D. V.; Duarte, A.; Ferrari, T. M.; Niekraszewicz, L. A. B.; Amaral, L.; Dias, J. F.

2018-02-01

In this work we present some results concerning the X-rays emitted by heavy ions during target bombardment. In this case, Cl4+ and Cl5+ ions with energies from 4 MeV to 10 MeV were employed to irradiate vitreous carbon planchets. Moreover, total X-ray production cross sections of titanium X-rays induced by chlorine ions were obtained as well for the same energy range. Only inner shell transitions were considered in the present work. The titanium target consisted of a thin film deposited over vitreous carbon planchets. The results indicate that the projectile X-ray yields increase as a function of the bombarding energy for the present energy range. Effects due to projectile charge state appears to be of minor importance at these low ion velocities. It is shown that a simple exponential function can represent the continuum background of such complex spectra. The chlorine transition rates Kβ/Kα obtained from chlorine acting as a projectile interacting with a carbon target are about half the value when compared to the chlorine Kβ/Kα ratios obtained when a LiCl target is bombarded with C+ and C3+ ions with energies from 2 MeV to 6 MeV. As far as the total X-ray production cross sections of Ti induced by chlorine ions are concerned, the ECPSSR theory underestimates the Ti total X-rays production cross sections by several orders of magnitude. The role of electron capture and possible mechanisms responsible for these effects are discussed.

Thermo-mechanical design aspects of mercury bombardment ion thrusters.

Science.gov (United States)

Schnelker, D. E.; Kami, S.

1972-01-01

The mechanical design criteria are presented as background considerations for solving problems associated with the thermomechanical design of mercury ion bombardment thrusters. Various analytical procedures are used to aid in the development of thruster subassemblies and components in the fields of heat transfer, vibration, and stress analysis. Examples of these techniques which provide computer solutions to predict and control stress levels encountered during launch and operation of thruster systems are discussed. Computer models of specific examples are presented.

RBS and NRA damage analysis on PFA films bombarded with hydrogen

Energy Technology Data Exchange (ETDEWEB)

Parada, Marco A.; Petchevist, Paulo C.D.; Minamisawa, Renato A.; Almeida, Adelaide de [Sao Paulo Univ., SP (Brazil). Inst. de Fisica]. E-mail: dalmeida@ffclrp.usp.br; Muntele, Claudiu I.; Zimmerman, Robert L.; Ila, Daryush [A and M University, Normal, AL (United States). Center for Irradiation of Materials]. E-mail: ila@cim.aamu.edu

2005-07-01

The fluoropolymer PFA (Tetrafluoroethylene-per-fluoromethoxy ethylene) is a conventional thermoplastic used in civil engineering applications such as anti-adherent coatings and concrete additives. It is also candidate materials for radiation dosimetry with applications in medical physics. When such a polymer is exposed to ionizing radiation, it can suffers damages that depend on the type, energy, and intensity of the radiation. We present results on the damage caused by 1 MeV protons at fluences of 10{sup 13}, 10{sup 14}, 10{sup 15}, and 10{sup 16} protons/cm{sup 2}. The energy deposited during such hydrogen bombardment breaks the polymeric chains with the release of fluorine in amounts directly proportional to the amount of deposited energy. Virgin samples were first analyzed by RBS. Subsequent damage was then profiled by monitoring the alpha emission spectrum, resulting from the nuclear reaction: {sup 19}F(p,{alpha}{gamma}){sup 16}O induced by 1.38 MeV protons on the remaining fluorine content of damaged polymer samples. (author)

Effect of Ni +-ION bombardment on nickel and binary nickel alloys

Science.gov (United States)

Roarty, K. B.; Sprague, J. A.; Johnson, R. A.; Smidt, F. A.

1981-03-01

Pure nickel and four binary nickel alloys have been subjected to high energy Ni ion bombardment at 675, 625 and 525°C. After irradiation, each specimen was studied by transmission electron microscopy. The pure nickel control was found to swell appreciably (1 to 5%) and the Ni-Al and the Ni-Ti samples were found to swell at all temperatures, but to a lesser degree (0.01 to 0.35%). The Ni-Mo contained a significant density of voids only at 525° C, while swelling was suppressed at all temperatures in the Ni-Si alloy. The dislocation structure progressed from loops to tangles as temperature increased in all materials except the Ni-Ti, in which there was an absence of loops at all temperatures. Dislocation densities decreased as temperature increased in all samples. These results do not correlate well with the relative behavior of the same alloys observed after neutron irradiation at 455°C. The differences between these two sets of data appear to be caused by different mechanisms controlling void nucleation in ion and neutron irradiation of these alloys.

Formation of a highly doped ultra-thin amorphous carbon layer by ion bombardment of graphene

Science.gov (United States)

Piotr Michałowski, Paweł; Pasternak, Iwona; Ciepielewski, Paweł; Guinea, Francisco; Strupiński, Włodek

2018-07-01

Ion bombardment of graphene leads to the formation of defects which may be used to tune properties of the graphene based devices. In this work, however, we present that the presence of the graphene layer on a surface of a sample has a significant impact on the ion bombardment process: broken sp2 bonds react with the incoming ions and trap them close to the surface of the sample, preventing a standard ion implantation. For an ion bombardment with a low impact energy and significant dose (in the range of 1014 atoms cm‑2) an amorphization of the graphene layer is observed but at the same time, most of the incoming ions do not penetrate the sample but stop at the surface, thus forming a highly doped ultra-thin amorphous carbon layer. The effect may be used to create thin layers containing desired atoms if no other technique is available. This approach is particularly useful for secondary ion mass spectrometry where a high concentration of Cs at the surface of a sample significantly enhances the negative ionization probability, allowing it to reach better detection limits.

Self-organised nano-structuring of thin oxide-films under swift heavy ion bombardment

International Nuclear Information System (INIS)

Bolse, Wolfgang

2006-01-01

Surface instabilities and the resulting self-organisation processes play an important role in nano-technology since they allow for large-array nano-structuring. We have recently found that the occurrence of such instabilities in thin film systems can be triggered by energetic ion bombardment and the subsequent self-assembly of the surface can be nicely controlled by fine-tuning of the irradiation conditions. The role of the ion in such processes is of double nature: If the instability is latently present already in the virgin sample, but self-assembly cannot take place because of kinetic barriers, the ion impact may just supply the necessary atomic mobility. On the other hand, the surface may become instable due to the ion beam induced material modifications and further irradiation then results in its reorganisation. In the present paper, we will review recently observed nano-scale self-organisation processes in thin oxide-films induced by the irradiation with swift heavy ions (SHI) at some MeV/amu energies. The first example is about SHI induced dewetting, which is driven by capillary forces already present in the as-deposited samples. The achieved dewetting pattern show an amazing similarity to those observed for liquid polymer films on Si, although in the present case the samples were kept at 80 K and hence have never reached their melting point. The second example is about self-organised lamellae formation driven by planar stresses, which are induced by SHI bombardment under grazing incidence and result in a surface instability and anisotropic plastic deformation (hammering effect). Taking advantage of these effects and modifying the irradiation procedure, we were able to generate more complex structures like NiO-'nano-towers' of 2 μm height and 200 nm in diameter

CEMENT KILN DUST AS A MATERIAL FOR BUILDING BLOCKS ...

African Journals Online (AJOL)

This paper presents the results of a study on the properties of hollow sandcrete blocks with cement kiln dust (CKD) as an additive and as a replacement for ordinary portland cement (OPC). When CKD was used as a replacement for cement, the compressive strength and density of blocks generally decreased with higher ...

Immediate fabrication of flower-like graphene oxide by ion beam bombardment

International Nuclear Information System (INIS)

Cheng, Junjie; Zhang, Yuanyuan; Zhang, Guilong; Xiong, Shiquan; Pei, Renjun; Cai, Dongqing; Wu, Zhengyan

2015-01-01

Graphical abstract: - Highlights: • Ion beam bombardment (IBB) could modify the microstructure of graphene oxide (GO). • IBB could transform a compact multi-layered GO to a few-layered flower-like GO. • IBB could effectively improve the dispersion and the related properties of GO. • The main mechanism was proposed to be the etching and charge effects of IBB. - Abstract: An effective and convenient method using ion beam bombardment (IBB) for separating a multi-layered compact graphene oxide (GO) piece into several small few-layered loose pieces was developed, and it was found that those small GO pieces had formed a flower-like structure. Therein, the main mechanism was proposed to be the etching and charge effects of IBB. This work could provide a facile and promising approach for improving the dispersion and the related properties of GO. Furthermore, X-ray diffraction and Raman spectrum determinations demonstrated that, with the increasing fluence, IBB could effectively decrease the chemical groups in the layers of GO, resulting in the decrease of the layer distance.

Immediate fabrication of flower-like graphene oxide by ion beam bombardment

Energy Technology Data Exchange (ETDEWEB)

Cheng, Junjie [Key Laboratory of Ion Beam Bioengineering, Hefei Institutes of Physical Science, Chinese Academy of Sciences and Anhui Province, Hefei, Anhui 230031 (China); Division of Nanobiomedicine, Key Laboratory for Nano-Bio Interface Research, Suzhou Institute of Nano-tech and Nano-bionics, Chinese Academy of Sciences, Suzhou 215123 (China); Zhang, Yuanyuan; Zhang, Guilong [Key Laboratory of Ion Beam Bioengineering, Hefei Institutes of Physical Science, Chinese Academy of Sciences and Anhui Province, Hefei, Anhui 230031 (China); University of Science and Technology of China, Hefei 230026 (China); Xiong, Shiquan [Key Laboratory of Ion Beam Bioengineering, Hefei Institutes of Physical Science, Chinese Academy of Sciences and Anhui Province, Hefei, Anhui 230031 (China); Pei, Renjun, E-mail: rjpei2011@sinano.ac.cn [Division of Nanobiomedicine, Key Laboratory for Nano-Bio Interface Research, Suzhou Institute of Nano-tech and Nano-bionics, Chinese Academy of Sciences, Suzhou 215123 (China); Cai, Dongqing, E-mail: dqcai@ipp.ac.cn [Key Laboratory of Ion Beam Bioengineering, Hefei Institutes of Physical Science, Chinese Academy of Sciences and Anhui Province, Hefei, Anhui 230031 (China); Wu, Zhengyan, E-mail: zywu@ipp.ac.cn [Key Laboratory of Ion Beam Bioengineering, Hefei Institutes of Physical Science, Chinese Academy of Sciences and Anhui Province, Hefei, Anhui 230031 (China)

2015-12-01

Graphical abstract: - Highlights: • Ion beam bombardment (IBB) could modify the microstructure of graphene oxide (GO). • IBB could transform a compact multi-layered GO to a few-layered flower-like GO. • IBB could effectively improve the dispersion and the related properties of GO. • The main mechanism was proposed to be the etching and charge effects of IBB. - Abstract: An effective and convenient method using ion beam bombardment (IBB) for separating a multi-layered compact graphene oxide (GO) piece into several small few-layered loose pieces was developed, and it was found that those small GO pieces had formed a flower-like structure. Therein, the main mechanism was proposed to be the etching and charge effects of IBB. This work could provide a facile and promising approach for improving the dispersion and the related properties of GO. Furthermore, X-ray diffraction and Raman spectrum determinations demonstrated that, with the increasing fluence, IBB could effectively decrease the chemical groups in the layers of GO, resulting in the decrease of the layer distance.

Suppression secondary electrons from target surface under pulsed ion beams bombardment

International Nuclear Information System (INIS)

Yang Zhen; Peng Yufei; Long Jidong; Lan Chaohui; Dong Pan; Shi Jinshui

2012-01-01

The producing mechanism of secondary electrons from target surface under ion beams bombardment is discussed. Several methods to suppress the secondary electrons in special vacuum devices and their advantages and disadvantages are introduced. The ways of using self-bias and curved surface target are proposed and verified in the experiment. The results show that the secondary electrons can be effectively suppressed when the self-bias is larger than 80 V. The secondary electron yield decreases by using curved surface target instead of flat target. The secondary electron yield calculated from the experimental data is about 0.67, which is slightly larger than the value (0.58) from the literature due to the impurities of the ion beam and target surface. The effect of suppressing the electron countercurrent by the self-bias method is analyzed. The result shows that the self-bias method can not only suppress the secondary electrons from target surface under ion beams bombardment, but also suppress the electron countercurrent resulting from the instability of the pulsed power source. (authors)

Blending of styrene-block-butadiene-block-styrene copolymer with sulfonated vinyl aromatic polymers

NARCIS (Netherlands)

Ruggeri, Giacomo; Passaglia, Elisa; Giorgi, Ivan; Picchioni, Francesco; Aglietto, Mauro

2001-01-01

Different polymers containing sulfonic groups attached to the phenyl rings were prepared by sulfonation of polystyrene (PS) and styrene-block-(ethylene-co-1-butene)-block-styrene (SEBS). The sulfonation degree (SD) was varied between 1 and 20 mol% of the styrene units. Polyphase materials containing

Measurement of induced radioactivity in a spallation neutron field of a mercury target for GeV-proton bombardment

International Nuclear Information System (INIS)

Kasugai, Y.; Takada, H.; Nakashima, H.

2001-01-01

An integral experiment on radioactivity induced in spallation neutron fields was carried out under the ASTE (AGS-Spallation Target Experiment) collaboration using AGS (Alternative Gradient Synchrotron) at BNL (Brookhaven National Laboratory). The spallation neutrons were produced by bombarding a mercury target with protons of 1.6, 12 and 24 GeV. The number of protons was 3 - 4 x 10 13 for each irradiation. The irradiated materials were titanium, nickel, cobalt, yttrium, and bismuth, and placed on the cylindrical surface of the mercury target at the distance of 15 - 16 cm from the beam-incident-surface of the target. Disintegration rates of induced radioactivities were measured at several cooling-time ranging from hours to months. The principal nuclides contributing to the radioactivity were pointed out for each material. The experimental results for bismuth were compared with the calculations with DCAHIN-SP code. (author)

Surface temperature measurements for ion-bombarded Si and GaAs at 1.0 to 2.0 MeV

International Nuclear Information System (INIS)

Lowe, L.F.; Kennedy, J.K.; Davies, D.E.; Deane, M.L.; Eyges, L.J.

1975-01-01

Surface temperatures of ion-bombarded silicon and gallium arsenide have been measured using an infrared detector. Ion beams of N + , N + 2 , O + , O + 2 , C + , CO + , and H + were used at energies from 1--2.0 MeV and at current densities up to 12 μAcenter-dotcm/sup -2/. No temperature dependence was found on ion species, energy, or current. The change in temperature depended only on beam power, target material, and sample mounting technique. With proper mounting temperature increases of 20 degreeC for silicon and 65 degreeC for gallium arsenide were observed for a beam power density of 1.0 Wcenter-dotcm/sup -2/

Fusion reactor materials

International Nuclear Information System (INIS)

Anon.

1977-01-01

The following topics are briefly discussed: (1) surface blistering studies on fusion reactor materials, (2) TFTR design support activities, (3) analysis of samples bombarded in-situ in PLT, (4) chemical sputtering effects, (5) modeling of surface behavior, (6) ion migration in glow discharge tube cathodes, (7) alloy development for irradiation performance, (8) dosimetry and damage analysis, and (9) development of tritium migration in fusion devices and reactors

A comparison of atom and ion induced SSIMS - evidence for a charge induced damage effect in insulator materials

International Nuclear Information System (INIS)

Brown, A.; Berg, J.A. van den; Vickerman, J.C.

1985-01-01

A static secondary ion mass spectrometry (SSIMS) study of two very low conductivity materials, polystyrene and niobium pentoxide, using on the one hand a primary ion beam with electron neutralisation, and on the other, atom bombardment, shows that whilst the initial spectra obtained were quite similar, subsequent damage effects were much greater under ion impact conditions. For an equivalent flux density the half-life of the polystyrene surface structure was four times longer under atom bombardment. Significant reduction of the niobium surface was observed under ion bombardment whereas an equivalent atom flux had little apparent effect on the surface oxidation state. These data suggest that the requirement to dissipate the charge delivered to the sample by the primary ion beam contributes significantly to the damage mechanisms in electrically insulating materials. (author)

Liquid crystal alignment in electro-responsive nanostructured thermosetting materials based on block copolymer dispersed liquid crystal

Energy Technology Data Exchange (ETDEWEB)

Tercjak, A; Garcia, I; Mondragon, I [Materials-Technologies Group, Departamento IngenierIa Quimica y M Ambiente, Escuela Politecnica, Universidad PaIs Vasco/Euskal Herriko Unibertsitatea, Plaza Europa 1, E-20018 Donostia-San Sebastian (Spain)], E-mail: scptesza@sc.ehu.es, E-mail: inaki.mondragon@ehu.es

2008-07-09

Novel well-defined nanostructured thermosetting systems were prepared by modification of a diglicydylether of bisphenol-A epoxy resin (DGEBA) with 10 or 15 wt% amphiphilic poly(styrene-b-ethylene oxide) block copolymer (PSEO) and 30 or 40 wt% low molecular weight liquid crystal 4'-(hexyl)-4-biphenyl-carbonitrile (HBC) using m-xylylenediamine (MXDA) as a curing agent. The competition between well-defined nanostructured materials and the ability for alignment of the liquid crystal phase in the materials obtained has been studied by atomic and electrostatic force microscopy, AFM and EFM, respectively. Based on our knowledge, this is the first time that addition of an adequate amount (10 wt%) of a block copolymer to 40 wt% HBC-(DGEBA/MXDA) leads to a well-organized nanostructured thermosetting system (between a hexagonal and worm-like ordered structure), which is also electro-responsive with high rate contrast. This behavior was confirmed using electrostatic force microscopy (EFM), by means of the response of the HBC liquid crystal phase to the voltage applied to the EFM tip. In contrast, though materials containing 15 wt% PSEO and 30 wt% HBC also form a well-defined nanostructured thermosetting system, they do not show such a high contrast between the uncharged and charged surface.

Liquid crystal alignment in electro-responsive nanostructured thermosetting materials based on block copolymer dispersed liquid crystal.

Science.gov (United States)

Tercjak, A; Garcia, I; Mondragon, I

2008-07-09

Novel well-defined nanostructured thermosetting systems were prepared by modification of a diglicydylether of bisphenol-A epoxy resin (DGEBA) with 10 or 15 wt% amphiphilic poly(styrene-b-ethylene oxide) block copolymer (PSEO) and 30 or 40 wt% low molecular weight liquid crystal 4'-(hexyl)-4-biphenyl-carbonitrile (HBC) using m-xylylenediamine (MXDA) as a curing agent. The competition between well-defined nanostructured materials and the ability for alignment of the liquid crystal phase in the materials obtained has been studied by atomic and electrostatic force microscopy, AFM and EFM, respectively. Based on our knowledge, this is the first time that addition of an adequate amount (10 wt%) of a block copolymer to 40 wt% HBC-(DGEBA/MXDA) leads to a well-organized nanostructured thermosetting system (between a hexagonal and worm-like ordered structure), which is also electro-responsive with high rate contrast. This behavior was confirmed using electrostatic force microscopy (EFM), by means of the response of the HBC liquid crystal phase to the voltage applied to the EFM tip. In contrast, though materials containing 15 wt% PSEO and 30 wt% HBC also form a well-defined nanostructured thermosetting system, they do not show such a high contrast between the uncharged and charged surface.

Liquid crystal alignment in electro-responsive nanostructured thermosetting materials based on block copolymer dispersed liquid crystal

International Nuclear Information System (INIS)

Tercjak, A; Garcia, I; Mondragon, I

2008-01-01

Novel well-defined nanostructured thermosetting systems were prepared by modification of a diglicydylether of bisphenol-A epoxy resin (DGEBA) with 10 or 15 wt% amphiphilic poly(styrene-b-ethylene oxide) block copolymer (PSEO) and 30 or 40 wt% low molecular weight liquid crystal 4'-(hexyl)-4-biphenyl-carbonitrile (HBC) using m-xylylenediamine (MXDA) as a curing agent. The competition between well-defined nanostructured materials and the ability for alignment of the liquid crystal phase in the materials obtained has been studied by atomic and electrostatic force microscopy, AFM and EFM, respectively. Based on our knowledge, this is the first time that addition of an adequate amount (10 wt%) of a block copolymer to 40 wt% HBC-(DGEBA/MXDA) leads to a well-organized nanostructured thermosetting system (between a hexagonal and worm-like ordered structure), which is also electro-responsive with high rate contrast. This behavior was confirmed using electrostatic force microscopy (EFM), by means of the response of the HBC liquid crystal phase to the voltage applied to the EFM tip. In contrast, though materials containing 15 wt% PSEO and 30 wt% HBC also form a well-defined nanostructured thermosetting system, they do not show such a high contrast between the uncharged and charged surface

Effect of Ar bombardment on the electrical and optical properties of ...

Indian Academy of Sciences (India)

The influence of low-energy Ar ion beam irradiation on both electrical and optical properties of low-density polyethylene (LDPE) films is presented. The polymer films were bombarded with 320 keV Ar ions with fuences up to 1 × 10 15 cm − 2 . Electrical properties of LDPE films were measured and the effect of ion ...

Molecular projectile effects for kinetic electron emission from carbon- and metal-surfaces bombarded by slow hydrogen ions

International Nuclear Information System (INIS)

Cernusca, S.; Winter, H.P.; Aumayr, F.; Diez Muino, R.; Juaristi, J.I.

2003-01-01

Total yields for kinetic electron emission (KE) have been determined for impact of hydrogen monomer-, dimer- and trimer-ions (impact energy <10 keV) on atomically clean surfaces of carbon-fiber inforced graphite used as first-wall armour in magnetic fusion devices. The data are compared with KE yields for impact of same projectile ions on atomically clean highly oriented pyrolytic graphite and polycrystalline gold. We discuss KE yields for the different targets if bombarded by equally fast molecular and atomic ions in view to 'projectile molecular effects' (different yields per proton for equally fast atomic and molecular ions), which are expected from calculated electronic projectile energy losses in these target materials

Molecular projectile effects for kinetic electron emission from carbon- and metal-surfaces bombarded by slow hydrogen ions

CERN Document Server

Cernusca, S; Aumayr, F; Diez-Muino, R; Juaristi, J I

2003-01-01

Total yields for kinetic electron emission (KE) have been determined for impact of hydrogen monomer-, dimer- and trimer-ions (impact energy <10 keV) on atomically clean surfaces of carbon-fiber inforced graphite used as first-wall armour in magnetic fusion devices. The data are compared with KE yields for impact of same projectile ions on atomically clean highly oriented pyrolytic graphite and polycrystalline gold. We discuss KE yields for the different targets if bombarded by equally fast molecular and atomic ions in view to 'projectile molecular effects' (different yields per proton for equally fast atomic and molecular ions), which are expected from calculated electronic projectile energy losses in these target materials.

On the modification of metal/ceramic interfaces by low energy ion/atom bombardment during film growth

International Nuclear Information System (INIS)

Rigsbee, J.M.; Scott, P.A.; Knipe, R.K.; Hock, V.F.

1986-01-01

Elemental Cu and Ti films have been deposited onto ceramic substrates with a plasma-aided physical vapor deposition (ion-plating) process. This paper discusses how the structure and chemistry of the metallic film and the metal/ceramic interface are modified by low energy ion and neutral atom bombardment. Emphasis is placed on determining how low energy ion/neutral atom bombardment affects the strength of the metal/ceramic interface. Analyses of the film, interface and substrate regions have employed scanning Auger microprobe, secondary ion mass spectroscopy, SEM/STEM-energy dispersive X-ray and TEM/STEM imaging and microdiffraction techniques. (Auth.)

X-ray diffraction study of stress relaxation in cubic boron nitride films grown with simultaneous medium-energy ion bombardment

International Nuclear Information System (INIS)

Abendroth, B.; Gago, R.; Eichhorn, F.; Moeller, W.

2004-01-01

Relaxation of the intrinsic stress of cubic boron nitride (cBN) thin films has been studied by x-ray diffraction (XRD) using synchrotron light. The stress relaxation has been attained by simultaneous medium-energy ion bombardment (2-10 keV) during magnetron sputter deposition, and was confirmed macroscopically by substrate curvature measurements. In order to investigate the stress-release mechanisms, XRD measurements were performed in in-plane and out-of-plane geometry. The analysis shows a pronounced biaxial state of compressive stress in the cBN films grown without medium-energy ion bombardment. This stress is partially released during the medium-energy ion bombardment. It is suggested that the main path for stress relaxation is the elimination of strain within the cBN grains due to annealing of interstitials

Titanium oxidation-reduction at low oxygen pressure under electron bombardment

International Nuclear Information System (INIS)

Brasca, R.; Passeggi, M.C.G.; Ferron, J.

2006-01-01

The effect of the electron bombardment on the first stages of the titanium oxidation process has been studied by means of Auger Electron Spectroscopy. Using Factor Analysis and the valence electron dependence behaviour of the titanium LMV Auger transition, we found that the process is strongly dependent on the oxygen pressure and electron current density. Depending on the irradiation conditions, films of different thickness and Ti oxidized states are obtained

Treatment of PVC using an alternative low energy ion bombardment procedure

Science.gov (United States)

Rangel, Elidiane C.; dos Santos, Nazir M.; Bortoleto, José Roberto R.; Durrant, Steven F.; Schreiner, Wido H.; Honda, Roberto Y.; Rangel, Rita de Cássia C.; Cruz, Nilson C.

2011-12-01

In many applications, polymers have progressively substituted traditional materials such as ceramics, glasses, and metals. Nevertheless, the use of polymeric materials is still limited by their surface properties. Frequently, selective modifications are necessary to suit the surface to a given application. Amongst the most common treatments, plasma immersion ion implantation (PIII) has attracted the attention of many researchers owing to its versatility and practicality. This method, however, requires a power supply to provide high voltage (tens of kV) negative pulses, with a controlled duty cycle, width and frequency. Owing to this, the implementation of PIII on the industrial scale can become economically inviable. In this work, an alternative plasma treatment that enables low energy ion bombardment without the need of a high voltage pulse generator is presented. To evaluate the efficiency of the treatment of polymers, polyvinylchloride, PVC, specimens were exposed to 5 Pa argon plasmas for 3600 s, at excitation powers, P, of between 10 and 125 W. Through contact angle and atomic force microscopy data, the influence of P on the wettability, surface free energy and roughness of the samples was studied. Surface chemical composition was measured by X-ray photoelectron spectroscopy, XPS. To evaluate the effect of aging under atmospheric conditions, contact angle and XPS measurements were performed one and 1334 days after the treatment. The plasma potential and ion density around the driven electrode were determined from Langmuir probe measurements while the self-bias potential was derived with the aid of an oscilloscope. From these data it was possible to estimate the mean energy of ions bombarding the PVC surface. Chlorine, carbon and oxygen contamination were detected on the surface of the as-received PVC. Upon exposure to the plasma, the proportion of chlorine was observed to decrease while that of oxygen increased. Consequently, the wettability and surface energy

Treatment of PVC using an alternative low energy ion bombardment procedure

International Nuclear Information System (INIS)

Rangel, Elidiane C.; Santos, Nazir M. dos; Bortoleto, José Roberto R.; Durrant, Steven F.; Schreiner, Wido H.; Honda, Roberto Y.; Cássia C Rangel, Rita de; Cruz, Nilson C.

2011-01-01

In many applications, polymers have progressively substituted traditional materials such as ceramics, glasses, and metals. Nevertheless, the use of polymeric materials is still limited by their surface properties. Frequently, selective modifications are necessary to suit the surface to a given application. Amongst the most common treatments, plasma immersion ion implantation (PIII) has attracted the attention of many researchers owing to its versatility and practicality. This method, however, requires a power supply to provide high voltage (tens of kV) negative pulses, with a controlled duty cycle, width and frequency. Owing to this, the implementation of PIII on the industrial scale can become economically inviable. In this work, an alternative plasma treatment that enables low energy ion bombardment without the need of a high voltage pulse generator is presented. To evaluate the efficiency of the treatment of polymers, polyvinylchloride, PVC, specimens were exposed to 5 Pa argon plasmas for 3600 s, at excitation powers, P, of between 10 and 125 W. Through contact angle and atomic force microscopy data, the influence of P on the wettability, surface free energy and roughness of the samples was studied. Surface chemical composition was measured by X-ray photoelectron spectroscopy, XPS. To evaluate the effect of aging under atmospheric conditions, contact angle and XPS measurements were performed one and 1334 days after the treatment. The plasma potential and ion density around the driven electrode were determined from Langmuir probe measurements while the self-bias potential was derived with the aid of an oscilloscope. From these data it was possible to estimate the mean energy of ions bombarding the PVC surface. Chlorine, carbon and oxygen contamination were detected on the surface of the as-received PVC. Upon exposure to the plasma, the proportion of chlorine was observed to decrease while that of oxygen increased. Consequently, the wettability and surface energy

Friction and wear measurements of sputtered MoS/sub x/ films amorphized by ion bombardment

International Nuclear Information System (INIS)

Mikkelsen, N.J.; Chevallier, J.; Soerensen, G.; Straede, C.A.

1988-01-01

The present study presents an experimental evidence for amorphization of rf sputtered MoS/sub x/ films by ion bombardment. Even at low doses (3 x 10 15 ions/cm 2 ) of 400 keV argon ions a complete amorphization was confirmed by x-ray diffraction analysis and transmission electron microscopy. As a result of the ion bombardment the film density increased 100% to almost the bulk value for MoS 2 . The friction coefficient for ion beam amorphized MoS/sub x/ was measured to be 0.04 in agreement with the values reported for crystalline films but disagreeing considerably with the friction coefficient of 0.4 previously reported for amorphous films

High Energy Ion Bombardment Simulation Facility at the University of Pittsburgh

International Nuclear Information System (INIS)

McGruer, J.N.; Choyke, W.J.; Doyle, N.J.; Spitznagel, J.A.

1975-01-01

The High Energy Ion Bombardment Simulation (HEIBS) Facility located at the University of Pittsburgh is now operational. The E-22 tandem accelerator of the Nuclear Physics Laboratory, fitted with a UNIS source, provides the heavy high energy ions. An auxiliary Van de Graaff accelerator is used for the simultaneous production of He ions. Special features of the simulation laboratory are reported

Polymerization of solid C60 under C60 cluster ion bombardment

Czech Academy of Sciences Publication Activity Database

Lavrentiev, Vasyl; Vacík, Jiří; Naramoto, H.; Narumi, K.

2009-01-01

Roč. 95, - (2009), s. 867-873 ISSN 0947-8396 R&D Projects: GA AV ČR(CZ) KAN400480701; GA MŠk(CZ) LC06041 Institutional research plan: CEZ:AV0Z10480505 Keywords : fulleren * cluster * bombardment * polymerization Subject RIV: BG - Nuclear, Atomic and Molecular Physics, Colliders Impact factor: 1.595, year: 2009 http://www.springerlink.com/content/0947-8396

The interpretation of ellipsometric measurements of ion bombardment of noble gases on semiconductor surfaces

NARCIS (Netherlands)

Holtslag, A.H.M.; Slager, U.C.; van Silfhout, Arend

1985-01-01

Low energy noble gas ion bombardment and thermal desorption studies were carried out on Si(111) and analysed, in situ, using spectroscopic ellipsometry. The amorphous layer thickness and implanted noble gas fraction were calculated.

Metallo-supramolecular block copolymer micelles

NARCIS (Netherlands)

Gohy, J.M.W.

2009-01-01

Supramolecular copolymers have become of increasing interest in recent years in the search for new materials with tunable properties. In particular, metallo-supramolecular block copolymers in which metal-ligand complexes are introduced in block copolymer architectures, have known important progress,

Electron bombardment fusion and continuous casting of uranium carbide. Fundamental study of the metallurgical and thermal processes

International Nuclear Information System (INIS)

Trouve, J.

1968-02-01

During a pilot production run, about 1.200 kg of uranium carbide cylindrical rods were prepared by electron bombardment fusion and continuous casting in an apparatus making it possible to operate in a constant vacuum automatically. In order to make the most of the fusion technique used, it was necessary to resolve a certain number of problems involved in this production. It was found that the energy yield for the electron bombardment heating using accelerating voltages of about 10 kV was 100 per cent; about 40 per cent of the electrons are re-emitted by back-scattering. These electrons leave the surface with practically zero energy. The fusion technique leads to the elimination of the majority of the metallic impurities. In order to explain the variations in the non-metallic impurity contents the different reactions occurring in the molten uranium monocarbide have been determined. A micrographic study of the rods obtained has shown various types of crystallization depending on the rate of casting and, despite the uniaxial symmetry of the cooling, no texture has been observed, whatever the rate of fusion employed. The aspects of the fracture surfaces observed on certain rods can be explained by theory in the domain where the material is elastic. Furthermore it has been shown that a decrease in the brittleness occurs as a result of the formation of fine precipitates of the Wiedmanstatten structure type. (authors) [fr

In-Situ atomic force microscopic observation of ion beam bombarded plant cell envelopes

International Nuclear Information System (INIS)

Sangyuenyongpipat, S.; Yu, L.D.; Brown, I.G.; Seprom, C.; Vilaithong, T.

2007-01-01

A program in ion beam bioengineering has been established at Chiang Mai University (CMU), Thailand, and ion beam induced transfer of plasmid DNA molecules into bacterial cells (Escherichia coli) has been demonstrated. However, a good understanding of the fundamental physical processes involved is lacking. In parallel work, onion skin cells have been bombarded with Ar + ions at energy 25 keV and fluence1-2 x 10 15 ions/cm 2 , revealing the formation of microcrater-like structures on the cell wall that could serve as channels for the transfer of large macromolecules into the cell interior. An in-situ atomic force microscope (AFM) system has been designed and installed in the CMU bio-implantation facility as a tool for the observation of these microcraters during ion beam bombardment. Here we describe some of the features of the in-situ AFM and outline some of the related work

Organic photovoltaic cell incorporating electron conducting exciton blocking layers

Science.gov (United States)

Forrest, Stephen R.; Lassiter, Brian E.

2014-08-26

The present disclosure relates to photosensitive optoelectronic devices including a compound blocking layer located between an acceptor material and a cathode, the compound blocking layer including: at least one electron conducting material, and at least one wide-gap electron conducting exciton blocking layer. For example, 3,4,9,10 perylenetetracarboxylic bisbenzimidazole (PTCBI) and 1,4,5,8-napthalene-tetracarboxylic-dianhydride (NTCDA) function as electron conducting and exciton blocking layers when interposed between the acceptor layer and cathode. Both materials serve as efficient electron conductors, leading to a fill factor as high as 0.70. By using an NTCDA/PTCBI compound blocking layer structure increased power conversion efficiency is achieved, compared to an analogous device using a conventional blocking layers shown to conduct electrons via damage-induced midgap states.

Ion bombardment and adsorption studies on ilmenite (FeTiO3) by X-ray photoelectron spectroscopy

International Nuclear Information System (INIS)

Schulze, P.D.

1983-01-01

The effects of 5 KeV argon and oxygen ion bombardment on FeTiO3 (ilmenite) at low temperatures have been studied using x-ray photoelectron spectroscopy (XPS). Also, using this same technique, the adsorption of O 2 , NO, N 2 O, and CO at 300 K and the adsorption of O 2 and D 2 O at 150K have been studied. Argon and oxygen ion bombardment of ilmenite have confirmed earlier studies on metal oxides that argon ions generally reduce the anion species while oxygen ions generally oxidize the anion species. The two iron states involved were Fe sup +2 and Fe sup O. The reduction of Ti sup +4 was not verified although a significant shift in the Ti(2p1,3) binding energies toward the metallic state was observed after oxygen ion bombardment at low temperatures. At temperatures above 150K, O 2 adsorbs dissociatively on ilmenite while D 2 O adsorbs molecularly below 170K. Above 300 K NO, N 2 O, and CO do not appear to adsorb dissociatively. Low temperature adsorption of D 2 O was found to be inhibited by predosing the ilmenite with O 2

Ion bombardment and adsorption studies on ilmenite (FeTiO3) by X-ray photoelectron spectroscopy

Science.gov (United States)

Schulze, P. D.

1983-01-01

The effects of 5 KeV argon and oxygen ion bombardment on FeTiO3 (ilmenite) at low temperatures have been studied using X-ray photoelectron spectroscopy (XPS). Also, using this same technique, the adsorption of O2, NO, N2O, and CO at 300 K and the adsorption of O2 and D2O at 150K have been studied. Argon and oxygen ion bombardment of ilmenite have confirmed earlier studies on metal oxides that argon ions generally reduce the anion species while oxygen ions generally oxidize the anion species. The two iron states involved were Fe sup +2 and Fe sup O. The reduction of Ti sup +4 was not verified although a significant shift in the Ti(2p1,3) binding energies toward the metallic state was observed after oxygen ion bombardment at low temperatures. At temperatures above 150K, O2 adsorbs dissociatively on ilmenite while D2O adsorbs molecularly below 170K. Above 300 K No, N2O, and CO do not appear to adsorb dissociatively. Low temperature adsorption of D2O was found to be inhibited by predosing the ilmenite with O2.

Naming Block Structures: A Multimodal Approach

Science.gov (United States)

Cohen, Lynn; Uhry, Joanna

2011-01-01

This study describes symbolic representation in block play in a culturally diverse suburban preschool classroom. Block play is "multimodal" and can allow children to experiment with materials to represent the world in many forms of literacy. Combined qualitative and quantitative data from seventy-seven block structures were collected and analyzed.…

Measurement of induced radioactivity in a spallation neutron field of a mercury target for GeV-proton bombardment

Energy Technology Data Exchange (ETDEWEB)

Kasugai, Y.; Takada, H.; Nakashima, H. [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment] [and others

2001-03-01

An integral experiment on radioactivity induced in spallation neutron fields was carried out under the ASTE (AGS-Spallation Target Experiment) collaboration using AGS (Alternative Gradient Synchrotron) at BNL (Brookhaven National Laboratory). The spallation neutrons were produced by bombarding a mercury target with protons of 1.6, 12 and 24 GeV. The number of protons was 3 - 4 x 10{sup 13} for each irradiation. The irradiated materials were titanium, nickel, cobalt, yttrium, and bismuth, and placed on the cylindrical surface of the mercury target at the distance of 15 - 16 cm from the beam-incident-surface of the target. Disintegration rates of induced radioactivities were measured at several cooling-time ranging from hours to months. The principal nuclides contributing to the radioactivity were pointed out for each material. The experimental results for bismuth were compared with the calculations with DCAHIN-SP code. (author)

Conical surface textures formed by ion bombarding 2% Be-Cu alloy

International Nuclear Information System (INIS)

Panitz, J.K.G.

1991-01-01

A homogeneous, micrometer-sized conical surface texture forms on 2% Be-Cu alloy which is bombarded with an argon beam produced by a Kaufman ion source. The dimensions of the features that form depend strongly on argon energy (from 250 to 1500 eV); argon fluence (10 19 to 10 20 ions cm -2 ); and argon flux (0.1 to 1 mA cm -2 ). The texture morphology depends less strongly on the background ambient (Mo versus graphite), earlier alloy heat treatments and the temperature during bombardment (100 o C and 450 o C). As the texture matures with increasing fluence, the number of large features increases at the expense of the number of small features. The observed relationship between texture formation and ion flux suggests that the evolution of these features is not adequately described by theories predicting that the mature conical side-wall angle is related to the angle of the maximum sputtering yield. These textured surfaces can be coated with other metals for a variety of possible applications including pulsed power Li + beam anodes; cold cathode field emission devices; optical absorbers and catalysis supports. (author)

Conical surface textures formed by ion bombarding 2% Be Cu alloy

International Nuclear Information System (INIS)

Panitz, J.K.G.

1990-01-01

A homogeneous, micrometer-sized conical surface texture forms on 2% Be-Cu alloy which is bombarded with an argon beam produced by a Kaufman ion source. The dimensions of the features that form strongly depend on: (1) argon energy (from 250 to 1500 eV), (2) fluence (10 19 to 10 20 ions/cm 2 ), and (3) flux (0.1 to 1 mA/cm 2 ). The texture morphology depends less strongly on the background ambient (Mo vs graphite), earlier alloy heat treatments and the temperature during bombardment (100 degree C and 450 degree C). As the texture matures with increasing fluence, the number of large features increases at the expense of the number of small features. The observed relationship between texture formation and ion flux suggests that the evolution of these features is not adequately described by theories predicting that the mature conical sidewall angle is related to the angle of the maximum sputtering yield. These textured surfaces can be coated with other metals for a variety of possible applications including: (1) pulsed power Li+ beam anodes, (2) cold cathode field emission devices, (3) optical absorbers and (4) catalysis supports. 18 refs., 5 figs

Development of soil-cement blocks with three interventions: natural soil, soil corrected with sand and soil more phase change materials (PCMs)

International Nuclear Information System (INIS)

Dantas, Valter Bezerra; Gomes, Uilame Umbelino; Reis, Edmilson Pedreira; Valcacer, Samara Melo; Silva, A.S.

2014-01-01

In this work, the results of characterization tests of soil samples collected in Mossoro-RN, UFERSA-RN Campus, located approximately 20 meters high, and "5 ° 12'34.68 south latitude and 37 ° 19'5.74 "west longitude, with the purpose of producing soil-cement for the manufacture of pressed blocks with good resistance to compression and thermal stability. The following tests were performed: granulometry, plasticity limit, liquidity limit, particle size correction, scanning electron microscopy (SEM), X-ray fluorescence. In this soil, based on the results of the granulometric analysis, 10% of medium sand with 3% and 5% of eicosane paraffin and 10% of medium sand with 3% and 5% of paraffin 120 / 125F were added, forming analysis compositions, standard soil-cement block and natural soil-cement block with addition of 10% medium sand and 0% paraffin. Paraffins are referred to as PCMs (Phase Change Material). The contrasting effect between the different dosages on the compressive strength values of the soil-cement blocks was observed. The objective is to create new materials that give the block quality equal to or higher than the recommendations of ABNT norms, and that offer greater thermal comfort in the constructions. Soil particles of different sizes were added to 8% (by weight) of cement, and about 9.20% of water added to the mixture

Thermal stress analysis of HTGR fuel and control rod fuel blocks in the HTGR in-block carbonization and annealing furnace

International Nuclear Information System (INIS)

Gwaltney, R.C.; McAfee, W.J.

1977-01-01

A new approach that utilizes the equivalent solid plate method has been applied to the thermal stress analysis of HTGR fuel and control rod fuel blocks. Cases were considered where these blocks, loaded with reprocessed HTGR fuel pellets, were being cured at temperatures up to 1800 0 C. A two-dimensional segment of a fuel block cross section including fuel, coolant holes, and graphite matrix was analyzed using the ORNL HEATING3 heat transfer code to determine the temperature-dependent effective thermal conductivity for the perforated region of the block. Using this equivalent conductivity to calculate the temperature distributions through different cross sections of the blocks, two-dimensional thermal-stress analyses were performed through application of the equivalent solid plate method. In this approach, the perforated material is replaced by solid homogeneous material of the same external dimensions but whose material properties have been modified to account for the perforations

Block copolymer based composition and morphology control in nanostructured hybrid materials for energy conversion and storage: solar cells, batteries, and fuel cells

KAUST Repository

Orilall, M. Christopher

2011-01-01

The development of energy conversion and storage devices is at the forefront of research geared towards a sustainable future. However, there are numerous issues that prevent the widespread use of these technologies including cost, performance and durability. These limitations can be directly related to the materials used. In particular, the design and fabrication of nanostructured hybrid materials is expected to provide breakthroughs for the advancement of these technologies. This tutorial review will highlight block copolymers as an emerging and powerful yet affordable tool to structure-direct such nanomaterials with precise control over structural dimensions, composition and spatial arrangement of materials in composites. After providing an introduction to materials design and current limitations, the review will highlight some of the most recent examples of block copolymer structure-directed nanomaterials for photovoltaics, batteries and fuel cells. In each case insights are provided into the various underlying fundamental chemical, thermodynamic and kinetic formation principles enabling general and relatively inexpensive wet-polymer chemistry methodologies for the efficient creation of multiscale functional materials. Examples include nanostructured ceramics, ceramic-carbon composites, ceramic-carbon-metal composites and metals with morphologies ranging from hexagonally arranged cylinders to three-dimensional bi-continuous cubic networks. The review ends with an outlook towards the synthesis of multicomponent and hierarchical multifunctional hybrid materials with different nano-architectures from self-assembly of higher order blocked macromolecules which may ultimately pave the way for the further development of energy conversion and storage devices. © 2011 The Royal Society of Chemistry.

Block copolymer based composition and morphology control in nanostructured hybrid materials for energy conversion and storage: solar cells, batteries, and fuel cells.

Science.gov (United States)

Orilall, M Christopher; Wiesner, Ulrich

2011-02-01

The development of energy conversion and storage devices is at the forefront of research geared towards a sustainable future. However, there are numerous issues that prevent the widespread use of these technologies including cost, performance and durability. These limitations can be directly related to the materials used. In particular, the design and fabrication of nanostructured hybrid materials is expected to provide breakthroughs for the advancement of these technologies. This tutorial review will highlight block copolymers as an emerging and powerful yet affordable tool to structure-direct such nanomaterials with precise control over structural dimensions, composition and spatial arrangement of materials in composites. After providing an introduction to materials design and current limitations, the review will highlight some of the most recent examples of block copolymer structure-directed nanomaterials for photovoltaics, batteries and fuel cells. In each case insights are provided into the various underlying fundamental chemical, thermodynamic and kinetic formation principles enabling general and relatively inexpensive wet-polymer chemistry methodologies for the efficient creation of multiscale functional materials. Examples include nanostructured ceramics, ceramic-carbon composites, ceramic-carbon-metal composites and metals with morphologies ranging from hexagonally arranged cylinders to three-dimensional bi-continuous cubic networks. The review ends with an outlook towards the synthesis of multicomponent and hierarchical multifunctional hybrid materials with different nano-architectures from self-assembly of higher order blocked macromolecules which may ultimately pave the way for the further development of energy conversion and storage devices.

Electron emission from molybdenum under ion bombardment

International Nuclear Information System (INIS)

Ferron, J.; Alonso, E.V.; Baragiola, R.A.; Oliva-Florio, A.

1981-01-01

Measurements are reported of electron emission yields of clean molybdenum surfaces under bombardment with H + , H 2 + , D + , D 2 + , He + , N + , N 2 + , O + , O 2 + , Ne + , Ar + , Kr + and Xe + in the wide energy range 0.7-60.2 keV. The clean surfaces were produced by inert gas sputtering under ultrahigh vacuum. The results are compared with those predicted by a core-level excitation model. The disagreement found when using correct values for the energy levels of Mo is traced to wrong assumptions in the model. A substantially improved agreement with experiment is obtained using a model in which electron emission results from the excitation of valence electrons from the target by the projectiles and fast recoiling target atoms. (author)

Electron bombardment fusion and continuous casting of uranium carbide. Fundamental study of the metallurgical and thermal processes; Fusion sous bombardement d'electrons et coulee continue de carbure d'uranium. Etude fondamentale des processus metallurgiques et thermiques

Energy Technology Data Exchange (ETDEWEB)

Trouve, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1968-02-01

During a pilot production run, about 1.200 kg of uranium carbide cylindrical rods were prepared by electron bombardment fusion and continuous casting in an apparatus making it possible to operate in a constant vacuum automatically. In order to make the most of the fusion technique used, it was necessary to resolve a certain number of problems involved in this production. It was found that the energy yield for the electron bombardment heating using accelerating voltages of about 10 kV was 100 per cent; about 40 per cent of the electrons are re-emitted by back-scattering. These electrons leave the surface with practically zero energy. The fusion technique leads to the elimination of the majority of the metallic impurities. In order to explain the variations in the non-metallic impurity contents the different reactions occurring in the molten uranium monocarbide have been determined. A micrographic study of the rods obtained has shown various types of crystallization depending on the rate of casting and, despite the uniaxial symmetry of the cooling, no texture has been observed, whatever the rate of fusion employed. The aspects of the fracture surfaces observed on certain rods can be explained by theory in the domain where the material is elastic. Furthermore it has been shown that a decrease in the brittleness occurs as a result of the formation of fine precipitates of the Wiedmanstatten structure type. (authors) [French] Au cours d'une fabrication pilote, environ 1 200 kg de barreaux cylindriques de carbure d'uranium ont ete prepares par fusion sous bombardement d'electrons et coulee continue dans un appareillage permettant d'operer d'une maniere automatique sous vide constant. Afin de tirer le meilleur parti possible de la technique de fusion utilisee, il importait de repondre a un certain nombre de questions soulevees par cette fabrication. Le rendement energetique du chauffage par bombardement d'electrons pour des tensions acceleratrices de l'ordre de 10 kV a ete

Comparison of compressive strength of paving block with a mixture of Sinabung ash and paving block with a mixture of lime

Science.gov (United States)

Hastuty, I. P.; Sembiringand Nursyamsi, I. S.

2018-02-01

Paving block is one of the material used as the top layer of road structure besides asphalt and concrete paving block is usually made of mixed material such as Portland cement or other adhesive material, water, and aggregate. People nowadays prefer paving block compared to other pavement such as concrete or asphalt. Their interest toward the use of paving block increase because paving block is an eco-friendly construction which is very useful in helping soil water conservation, can be done faster, has easier installation and maintenance, has a variety of shades that increase the aesthetic value, also costs cheaper than the other. Preparation of the specimens with a mixture of Sinabung ash and a mixture of Sinabung ash and lime are implemented with a mixture ratio of cement : sand : stone ash is 1: 2 : 3. The mixture is used as a substitute material by reducing the percentage amount of the weight of the cement with the composition ratio variation based on the comparative volume category of the paving block aggregate, i.e. 0%, 5%, 10%, 15%, 20%, and 25%. The result of this research shows that the maximum compressive strength value is 42.27 Mpa, it was obtained from a mixture of 10% lime with curing time 28 days. The maximum compressive strength value which is obtained from the mixture of sinabung ash is 41.60 Mpa, it was obtained from a mixture of 15% sinabung ash. From the use of these two materials, paving blocks produced are classified as paving blocks quality A and B (350 - 400 Mpa) in accordance to specification from SNI 03-0691-1996.

Films deposited from reactive sputtering of aluminum acetylacetonate under low energy ion bombardment

Energy Technology Data Exchange (ETDEWEB)

Battaglin, Felipe Augusto Darriba; Prado, Eduardo Silva; Cruz, Nilson Cristino da; Rangel, Elidiane Cipriano, E-mail: elidiane@sorocaba.unesp.br [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Sorocaba, SP (Brazil). Lab. de Plasmas Tecnologicos; Caseli, Luciano [Universidade Federal de Sao Paulo (UNIFESP), Diadema, SP (Brazil). Instituto de Ciencias Ambientais, Quimicas e Farmaceuticas; Silva, Tiago Fiorini da; Tabacniks, Manfredo Harri [Universidade de Sao Paulo (USP), SP (Brazil). Instituto de Fisica

2017-07-15

Films were deposited from aluminum acetylacetonate (Al(acac)3 ) using a methodology involving reactive sputtering and low energy ion bombardment. The plasma was generated by the application of radiofrequency power to the powder containing electrode and simultaneously, negative pulses were supplied to the electrode where the substrates were attached. It was investigated the effect of the duty cycle of the pulses (Δ) on the properties of the coatings. Association of ion bombardment to the deposition process increased film thickness, structure reticulation and organic content. Ions from the deposition environment were implanted at the film-air interface or underneath it. Morphology and topography were altered depending on Δ. Considering the enhancement of Δ, it affected the flux of ions reaching the depositing interface and then the deposition rate, H content, crosslinking degree and surface microstructure. Alumina groups were detected in the infrared spectra, whereas the precipitation of amorphous alumina was confirmed by X-ray diffraction. (author)

Responsive linear-dendritic block copolymers.

Science.gov (United States)

Blasco, Eva; Piñol, Milagros; Oriol, Luis

2014-06-01

The combination of dendritic and linear polymeric structures in the same macromolecule opens up new possibilities for the design of block copolymers and for applications of functional polymers that have self-assembly properties. There are three main strategies for the synthesis of linear-dendritic block copolymers (LDBCs) and, in particular, the emergence of click chemistry has made the coupling of preformed blocks one of the most efficient ways of obtaining libraries of LDBCs. In these materials, the periphery of the dendron can be precisely functionalised to obtain functional LDBCs with self-assembly properties of interest in different technological areas. The incorporation of stimuli-responsive moieties gives rise to smart materials that are generally processed as self-assemblies of amphiphilic LDBCs with a morphology that can be controlled by an external stimulus. Particular emphasis is placed on light-responsive LDBCs. Furthermore, a brief review of the biomedical or materials science applications of LDBCs is presented. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effects produced in GaAs by MeV ion bombardment

International Nuclear Information System (INIS)

Wie, C.R.

1985-01-01

The first part of this thesis presents work performed on the ionizing energy beam induced adhesion enhancement of thin (approx.500 A) Au films on GaAs substrates. The ionizing beam, employed in the present thesis, is the MeV ions (i.e., 16 O, 19 F, and 35 Cl), with energies between 1 and 20 MeV. Using the Scratch test for adhesion measurement, and ESCA for chemical analysis of the film substrate interface, the native oxide layer at the interface is shown to play an important role in the adhesion enhancement by the ionizing radiation. A model is discussed that explains the experimental data on the dependence of adhesion enhancement on the energy which was deposited into electronic processes at the interface. The second part of the thesis presents research results on the radiation damage in GaAs crystals produced by MeV ions. Lattice parameter dilatation in the surface layers of the GaAs crystals becomes saturated after a high dose bombardment at room temperature. The strain produced by nuclear collisions is shown to relax partially due to electronic excitation (with a functional dependence on the nuclear and electronic stopping power of bombarding ions. Data on the GaAs and GaP crystals suggest that low temperature recovery stage defects produce major crystal distortion

Triazole: a unique building block for the construction of functional materials.

Science.gov (United States)

Juríček, Michal; Kouwer, Paul H J; Rowan, Alan E

2011-08-21

Over the past 50 years, numerous roads towards carbon-based materials have been explored, all of them being paved using mainly one functional group as the brick: acetylene. The acetylene group, or the carbon-carbon triple bond, is one of the oldest and simplest functional groups in chemistry, and although not present in any of the naturally occurring carbon allotropes, it is an essential tool to access their synthetic carbon-rich family. In general, two strategies towards the synthesis of π-conjugated carbon-rich structures can be employed: (a) either the acetylene group serves as a building block to access acetylene-derived structures or (b) it serves as a synthetic tool to provide other, usually benzenoid, structures. The recently discovered copper-catalysed azide-alkyne cycloaddition (CuAAC) reaction, however, represents a new powerful alternative: it transforms the acetylene group into a five-membered heteroaromatic 1H-1,2,3-triazole (triazole) ring and this gives rise to new opportunities. Compared with all-carbon aromatic non-functional rings, the triazole ring possesses three nitrogen atoms and, thus, can serve as a ligand to coordinate metals, or as a hydrogen bond acceptor and donor. This Feature Article summarises examples of using the triazole ring to construct conjugation- and/or function-related heteroaromatic materials, such as tuneable multichromophoric covalent ensembles, macrocyclic receptors or responsive foldamers. These recent examples, which open a new sub-field within organic materials, started to appear only few years ago and represent "a few more bricks" on the road to carbon-rich functional materials. This journal is © The Royal Society of Chemistry 2011

Influence of substrate pre-treatments by Xe{sup +} ion bombardment and plasma nitriding on the behavior of TiN coatings deposited by plasma reactive sputtering on 100Cr6 steel

Energy Technology Data Exchange (ETDEWEB)

Vales, S., E-mail: sandra.vales@usp.br [Universidade de São Paulo (USP), Escola de Engenharia de São Carlos, Av. Trabalhador São Carlense 400, São Carlos, SP CEP 13566-590 (Brazil); Brito, P., E-mail: ppbrito@gmail.com [Pontifícia Universidade Católica de Minas Gerais (PUC-MG), Av. Dom José Gaspar 500, 30535-901 Belo Horizonte, MG (Brazil); Pineda, F.A.G., E-mail: pipe8219@gmail.com [Universidade de São Paulo (USP), Escola de Engenharia de São Carlos, Av. Trabalhador São Carlense 400, São Carlos, SP CEP 13566-590 (Brazil); Ochoa, E.A., E-mail: abigail_ochoa@hotmail.com [Universidade Estadual de Campinas (UNICAMP), Campus Universitário Zeferino Vaz, Barão Geraldo, Campinas, SP CEP 13083-970 (Brazil); Droppa, R., E-mail: roosevelt.droppa@ufabc.edu.br [Universidade Federal do ABC (UFABC), Av. dos Estados, 5001, Santo André, SP CEP 09210-580 (Brazil); Garcia, J., E-mail: jose.garcia@sandvik.com [Sandvik Coromant R& D, Lerkrogsvägen 19, SE-12680, Stockholm (Sweden); Morales, M., E-mail: monieriz@gmail.com [Universidade Estadual de Campinas (UNICAMP), Campus Universitário Zeferino Vaz, Barão Geraldo, Campinas, SP CEP 13083-970 (Brazil); Alvarez, F., E-mail: alvarez@ifi.unicamp.br [Universidade Estadual de Campinas (UNICAMP), Campus Universitário Zeferino Vaz, Barão Geraldo, Campinas, SP CEP 13083-970 (Brazil); and others

2016-07-01

In this paper the influence of pre-treating a 100Cr6 steel surface by Xe{sup +} ion bombardment and plasma nitriding at low temperature (380 °C) on the roughness, wear resistance and residual stresses of thin TiN coatings deposited by reactive IBAD was investigated. The Xe{sup +} ion bombardment was carried out using a 1.0 keV kinetic energy by a broad ion beam assistance deposition (IBAD, Kaufman cell). The results showed that in the studied experimental conditions the ion bombardment intensifies nitrogen diffusion by creating lattice imperfections, stress, and increasing roughness. In case of the combined pre-treatment with Xe{sup +} ion bombardment and subsequent plasma nitriding, the samples evolved relatively high average roughness and the wear volume increased in comparison to the substrates exposed to only nitriding or ion bombardment. - Highlights: • Effect of Xe ion bombardment and plasma nitriding on TiN coatings was investigated. • Xe ion bombardment with 1.0 KeV increases nitrogen retention in plasma nitriding. • 1.0 KeV ion impact energy causes sputtering, thus increasing surface roughness. • TiN coating wear is minimum after plasma nitriding due to lowest roughness.

Engineering catalytic activity via ion beam bombardment of catalyst supports for vertically aligned carbon nanotube growth

Science.gov (United States)

Islam, A. E.; Nikolaev, P.; Amama, P. B.; Zakharov, D.; Sargent, G.; Saber, S.; Huffman, D.; Erford, M.; Semiatin, S. L.; Stach, E. A.; Maruyama, B.

2015-09-01

Carbon nanotube growth depends on the catalytic activity of metal nanoparticles on alumina or silica supports. The control on catalytic activity is generally achieved by variations in water concentration, carbon feed, and sample placement on a few types of alumina or silica catalyst supports obtained via thin film deposition. We have recently expanded the choice of catalyst supports by engineering inactive substrates like c-cut sapphire via ion beam bombardment. The deterministic control on the structure and chemistry of catalyst supports obtained by tuning the degree of beam-induced damage have enabled better regulation of the activity of Fe catalysts only in the ion beam bombarded areas and hence enabled controllable super growth of carbon nanotubes. A wide range of surface characterization techniques were used to monitor the catalytically active surface engineered via ion beam bombardment. The proposed method offers a versatile way to control carbon nanotube growth in patterned areas and also enhances the current understanding of the growth process. With the right choice of water concentration, carbon feed and sample placement, engineered catalyst supports may extend the carbon nanotube growth yield to a level that is even higher than the ones reported here, and thus offers promising applications of carbon nanotubes in electronics, heat exchanger, and energy storage.

High-energy particle emission from galena and pyrite bombarded with Cs and O ions

International Nuclear Information System (INIS)

Karpuzov, D.S.; McIntyre, N.S.

2002-01-01

The ejection of energetic particles during steady-state ion surface bombardment has been investigated by means of a dynamic computer simulation as well as in a secondary ion mass spectrometry (SIMS)/low-energy ion scattering from surfaces (LEIS) experiment. The emphasis of this comparative study is on the mass dependence of high-energy tails in sputtering and backscattering for the bombardment of galena (PbS) and pyrite (FeS 2 ) with keV energy ion beam of cesium and oxygen. In the experiment, kinetic energy distributions of sputtered secondary ions (S + , Fe + , Pb + , S - ), as well as backscattered or re-sputtered primary ions (Cs + , O + , O - ), have been measured on a modified Cameca IMS-3f magnetic sector mass spectrometer for keV cesium (Cs + ) and oxygen (O 2 + , O - ) bombardment of galena and pyrite. Ejection of high-energy particles, with emission energies of up to ∼40% or up to ∼60% of the bombarding energy for sputtering of the lighter component (S ± ) with cesium or oxygen, respectively, and of up to ∼40% (Cs + ) and ∼80% (O ± ) for backscattering, has been observed for PbS. The computer simulations were based on the well-known MARLOWE code. In order to model the change of the stoichiometry of the binary compounds, dynamic modification of the target composition in the near-surface region was introduced. Cs incorporation was included, and a relative enrichment of the metallic component (Pb, Fe) in the top few layers due to preferential sputtering of sulfur was allowed. The computer simulations provide information on the formation of altered layer under sputter equilibrium as well as on the energy and angular emission distributions of sputtered and backscattered particles in steady-state conditions. Multiple scattering of Cs projectiles and dynamic re-sputtering of cesium that was previously incorporated in the altered near-surface region can be distinguished in the simulation, and matched with the experimental observations. In addition

Micro-shear bond strength of different resin cements to ceramic/glass-polymer CAD-CAM block materials.

Science.gov (United States)

Cekic-Nagas, Isil; Ergun, Gulfem; Egilmez, Ferhan; Vallittu, Pekka Kalevi; Lassila, Lippo Veli Juhana

2016-10-01

The aim of this study was to evaluate the effects of hydrofluoric acid treatment on bond strength of resin cements to three different types of ceramic/glass containing CAD-CAM block composite materials. CAD-CAM block materials of polymer infiltrated (Vita Enamic), resin nanoceramic (Lava Ultimate) and nanoceramic (Cerasmart) with a thickness of 1.5mm were randomly divided into two groups according to the surface treatment performed. In Group 1, specimens were wet-ground with silicon carbide abrasive papers up to no. 1000. In Group 2, 9.6% hydrofluoric acid gel was applied to ceramics. Three different resin cements (RelyX, Variolink Esthetic and G-CEM LinkAce) were applied to the tubes in 1.2-mm thick increments and light-cured for 40s using LED light curing unit. Half of the specimens (n=10) were submitted to thermal cycling (5000 cycles, 5-55°C). The strength measurements were accomplished with a universal testing machine (Lloyd Instruments) at a cross-head speed of 0.5mm/min until the failure occurs. Failure modes were examined using a stereomicroscope and scanning electron microscope. The data were analyzed with multivariate analysis of variance (MANOVA) and Tukey's post hoc tests (α=0.05). There were significant differences between ceramics and resin cements (pceramics (pceramic/glass-polymer materials might promote the bonding capacity of these systems. Copyright © 2016 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Influence of keV-He ion bombardment on the magnetic properties of Co/Pd multilayers

Energy Technology Data Exchange (ETDEWEB)

Mueglich, Nicolas; Buhl, Oliver; Weis, Tanja; Engel, Dieter; Ehresmann, Arno [Institute of Physics and Center for Interdisciplinary Nanostructure Science and Technology (CINSaT), University of Kassel (Germany); Hellwig, Olav [San Jose Research Center, HGST, A Western Digital Company, CA (United States)

2013-07-01

Thin films of ferromagnetic Co separated by Pd films with thicknesses in the first ferromagnetic maximum of interlayer exchange coupling are magnetically dominated by perpendicular-to-plane anisotropy and labyrinth stripe domain patterns in remanence. During the magnetization reversal of such a multilayer system domain nucleation and domain wall movement can be observed for different external magnetic fields H. The influence of keV-He ion bombardment on the microstructure of the system and its resultant decrease of magnetic anisotropy has been investigated by vibrating sample magnetometry, polar magneto-optical Kerr effect and magnetic force microscopy. It is shown that areas of ferromagnetic in-plane anisotropy are created due to the ion bombardement and that the system shows an increasing quotient of superparamagnetism in the deeper layers of the multilayersystem.

Depth profiling using C60+ SIMS-Deposition and topography development during bombardment of silicon

International Nuclear Information System (INIS)

Gillen, Greg; Batteas, James; Michaels, Chris A.; Chi, Peter; Small, John; Windsor, Eric; Fahey, Albert; Verkouteren, Jennifer; Kim, K.J.

2006-01-01

A C 60 + primary ion source has been coupled to an ion microscope secondary ion mass spectrometry (SIMS) instrument to examine sputtering of silicon with an emphasis on possible application of C 60 + depth profiling for high depth resolution SIMS analysis of silicon semiconductor materials. Unexpectedly, C 60 + SIMS depth profiling of silicon was found to be complicated by the deposition of an amorphous carbon layer which buries the silicon substrate. Sputtering of the silicon was observed only at the highest accessible beam energies (14.5 keV impact) or by using oxygen backfilling. C 60 + SIMS depth profiling of As delta-doped test samples at 14.5 keV demonstrated a substantial (factor of 5) degradation in depth resolution compared to Cs + SIMS depth profiling. This degradation is thought to result from the formation of an unusual platelet-like grain structure on the SIMS crater bottoms. Other unusual topographical features were also observed on silicon substrates after high primary ion dose C 60 + bombardment

Doubly versus singly positively charged oxygen ions back-scattered from a silicon surface under dynamic O2+ bombardment

International Nuclear Information System (INIS)

Franzreb, Klaus; Williams, Peter; Loerincik, Jan; Sroubek, Zdenek

2003-01-01

Mass-resolved (and emission-charge-state-resolved) low-energy ion back-scattering during dynamic O 2 + bombardment of a silicon surface was applied in a Cameca IMS-3f secondary ion mass spectrometry (SIMS) instrument to determine the bombarding energy dependence of the ratio of back-scattered O 2+ versus O + . While the ratio of O 2+ versus O + drops significantly at reduced bombarding energies, O 2+ back-scattered from silicon was still detectable at an impact energy (in the lab frame) as low as about 1.6 keV per oxygen atom. Assuming neutralization prior to impact, O 2+ ion formation in an asymmetric 16 O→ 28 Si collision is expected to take place via 'collisional double ionization' (i.e. by promotion of two outer O 2p electrons) rather than by the production of an inner-shell (O 2s or O 1s) core hole followed by Auger-type de-excitation during or after ejection. A molecular orbital (MO) correlation diagram calculated for a binary 'head-on' O-Si collision supports this interpretation

Radiographic and histological study of perennial bone defect repair in rat calvaria after treatment with blocks of porous bovine organic graft material.

Science.gov (United States)

Marins, Lucele Vieira; Cestari, Tania Mary; Sottovia, André Dotto; Granjeiro, José Mauro; Taga, Rumio

2004-03-01

Over the last few years, various bone graft materials of bovine origin to be used in oromaxillofacial surgeries have entered the market. In the present study, we determined the capacity of a block organic bone graft material (Gen-ox, Baumer SA, Brazil) prepared from bovine cancellous bone to promote the repair of critical size bone injuries in rat calvaria. A transosseous defect measuring approximately 8mm in diameter was performed with a surgical trephine in the parietal bone of 25 rats. In 15 animals, the defects were filled with a block of graft material measuring 8mm in diameter and soaked in the animal's own blood, and in the other 10 animals the defects were only filled with blood clots. The calvariae of rats receiving the material were collected 1, 3 and 6 months after surgery, and those of animals receiving the blood clots were collected immediately and 6 months after surgery. During surgery, the graft material was found to be of easy handling and to adapt perfectly to the receptor bed after soaking in blood. The results showed that, in most animals treated, the material was slowly resorbed and served as a space filling and maintenance material, favoring angiogenesis, cell migration and adhesion, and bone neoformation from the borders of the lesion. However, a foreign body-type granulomatous reaction, with the presence of numerous giant cells preventing local bone neoformation, was observed in two animals of the 1-month subgroup and in one animal of the 3-month subgroup. These cases were interpreted as resulting from the absence of demineralization and the lack of removal of potential antigen factors during production of the biomaterial. We conclude that, with improvement in the quality control of the material production, block organic bone matrix will become a good alternative for bone defect repair in the oromaxillofacial region due to its high osteoconductive capacity.

Transformation of triploid bermudagrass (Cynodon dactylon x C. transvaalensis cv. TifEagle) by means of biolistic bombardment.

Science.gov (United States)

Zhang, G; Lu, S; Chen, T A; Funk, C R; Meyer, W A

2003-06-01

A transformation system for triploid bermudagrass ( Cynodon dactylon x C. transvaalensis cv. TifEagle) was established with a biolistic bombardment delivery system. Embryogenic callus was induced from stolons and maintained on Murashige and Skoog's medium supplemented with 30 microM dicamba, 20 microM benzylaminopurine, and 100 mg/l myo-inositol. Using the hygromycin phosphotransferase ( hpt) gene as the selectable marker gene, we obtained 75 transgenic lines from 18 petri dishes bombarded. Integration of the hpt gene into genomic DNA and transcription of hpt was confirmed by Southern and Northern blot analyses, respectively. Through suspension culture screening, we obtained homogeneously transformed plants showing stable transcription of the hpt gene.

Measures to alleviate the back bombardment effect of thermionic rf electron gun

International Nuclear Information System (INIS)

Huang, Y.; Xie, J.

1991-01-01

Thermionic rf electron gun finds application as a high brightness electron source for rf linacs. However, cathode heating from back-bombardment effect causes a ramp in the macro-pulse beam current and limit the usable pulse width. Three methods: ring cathode, magnetic deflection and laser assisted heating are studied in theory and in experiment. The results of these studies are reported

Back bombardment for dispenser and lanthanum hexaboride cathodes

Directory of Open Access Journals (Sweden)

Mahmoud Bakr

2011-06-01

Full Text Available The back bombardment (BB effect limits wide usage of thermionic rf guns. The BB effect induces not only ramping-up of a cathode’s temperature and beam current, but also degradation of cavity voltage and beam energy during a macropulse. This paper presents a comparison of the BB effect for the case of dispenser tungsten-base (DC and lanthanum hexaboride (LaB_{6} thermionic rf gun cathodes. For each, particle simulation codes are used to simulate the BB effect and electron beam dynamics in a thermionic rf gun cathode. A semiempirical equation is also used to investigate the stopping range and deposited heat power of BB electrons in the cathode material. A numerical simulation method is used to calculate the change of the cathode temperature and current density during a single macropulse. This is done by solving two differential equations for the rf gun cavity equivalent circuit and one-dimensional thermal diffusion equation. High electron emission and small beam size are required for generation of a high-brightness electron beam, and so in this work the emission properties of the cathode are taken into account. Simulations of the BB effect show that, for a pulse of 6  μs duration, the DC cathode experiences a large change in the temperature compared with LaB_{6}, and a change in current density 6 times higher. Validation of the simulation results is performed using experimental data for beam current beyond the gun exit. The experimental data is well reproduced using the simulation method.

Photocatalytic pavement blocks. Air purification by pavement blocks. Final results of the research at BRRC

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-07-01

The use of materials can influence to a large extent the environmental impact of traffic and of road infrastructure. Especially in urban areas, where the risk on smog formation during hot summer days is high, the use of photocatalytic pavement blocks can reduce the air pollution significantly. A project on environmental friendly concrete pavement blocks is conducted at the Belgian Road Research Centre. The use of photocatalytic material in the surface of pavement blocks to obtain air purifying materials is investigated. In contact with light, TiO2 as photocatalyst, is able to reduce the NO and NO2 content in the air, caused by the exhaust of traffic. The efficiency is tested on pavement blocks, but the technique can as well be applied on other road elements (e.g. noise reducing walls, linear elements) or as a coating on new materials or existing structures. At the previous TRA conference in Gotenborgh, Sweden, the principle of photocatalysis was presented. In this paper, emphasis will be put on the final results of the 4-year project obtained in laboratory as well as on site at the Leien of Antwerp (10,000 m{sup 2}). The results indicate a durable efficiency towards NOx reduction, which is in favour for the diminishing of the risk on ozone formation. However, the precise translation from the laboratory towards the site is still in question. The results obtained during the project are discussed in this paper.

Photocatalytic pavement blocks. Air purification by pavement blocks. Final results of the research at BRRC

International Nuclear Information System (INIS)

2009-01-01

The use of materials can influence to a large extent the environmental impact of traffic and of road infrastructure. Especially in urban areas, where the risk on smog formation during hot summer days is high, the use of photocatalytic pavement blocks can reduce the air pollution significantly. A project on environmental friendly concrete pavement blocks is conducted at the Belgian Road Research Centre. The use of photocatalytic material in the surface of pavement blocks to obtain air purifying materials is investigated. In contact with light, TiO2 as photocatalyst, is able to reduce the NO and NO2 content in the air, caused by the exhaust of traffic. The efficiency is tested on pavement blocks, but the technique can as well be applied on other road elements (e.g. noise reducing walls, linear elements) or as a coating on new materials or existing structures. At the previous TRA conference in Gotenborgh, Sweden, the principle of photocatalysis was presented. In this paper, emphasis will be put on the final results of the 4-year project obtained in laboratory as well as on site at the Leien of Antwerp (10,000 m 2 ). The results indicate a durable efficiency towards NOx reduction, which is in favour for the diminishing of the risk on ozone formation. However, the precise translation from the laboratory towards the site is still in question. The results obtained during the project are discussed in this paper

Influence of ion bombardment on growth and properties of PLD created DLC films

Czech Academy of Sciences Publication Activity Database

Jelínek, Miroslav; Písařík, Petr; Kocourek, Tomáš; Zemek, Josef; Lukeš, J.

2013-01-01

Roč. 110, č. 4 (2013), s. 943-947 ISSN 0947-8396 R&D Projects: GA MŠk LD12069 Institutional research plan: CEZ:AV0Z10100522 Keywords : DLC * ion bombardment * sp3 /sp2 * thin films * PLD Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.694, year: 2013

The effect of incidence angle on ion bombardment induced surface topography development on single crystal copper

International Nuclear Information System (INIS)

Carter, G.; Nobes, M.J.; Lewis, G.W.; Whitton, J.L.

1982-01-01

The fluence dependence of development of microscopic surface features, particularly etch pits, during 9 keV Ar + ion bombardment of (11,3,1) oriented Cu single crystals has been studied employing quasi-dynamic irradiation and observation techniques in a scanning electron microscope-accelerator system. 9 keV ions are observed not to produce crystallographic pyramids under all irradiation conditions for this surface, a very different result from our earlier studies with higher energy ions. The bombardment does elaborate etch pits however, the habits and growth kinetics of which depend upon both polar and azimuthal angles of ion incidence to the surface. The results are explained in terms of differential erosion of crystal planes modified by the presence of pre-existing and irradiation induces extended defects. (orig.)

Strength and deformability of hollow concrete blocks: correlation of block and cylindrical sample test results

OpenAIRE

Barbosa, C. S.; Hanai, J.B.

2009-01-01

This paper deals with correlations among mechanical properties of hollow blocks and those of concrete used to make them. Concrete hollow blocks and test samples were moulded with plastic consistency concrete, to assure the same material in all cases, in three diferente levels of strength (nominally 10 N/mm², 20 N/mm² and 30 N/mm²). The mechanical properties and structural behaviour in axial compression and tension tests were determined by standard tests in blocks and cylinders. Stress and str...

Additional ion bombardment in PVD processes generated by a superimposed pulse bias voltage

International Nuclear Information System (INIS)

Olbrich, W.; Kampschulte, G.

1993-01-01

The superimposed pulse bias voltage is a tool to apply an additional ion bombardment during deposition in physical vapour deposition (PVD) processes. It is generated by the combination of a d.c. ground voltage and a higher d.c. pulse voltage. Using a superimposed pulse bias voltage in ion-assisted PVD processes effects an additional all-around ion bombardment on the surface with ions of higher energy. Both metal and reactive or inert-gas ions are accelerated to the surface. The basic principles and important characteristics of this newly developed process such as ion fluxes or deposition rates are shown. Because of pulsing the high voltage, the deposition temperature does not increase much. The adhesion, structure, morphology and internal stresses are influenced by these additional ion impacts. The columnar growth of the deposited films could be suppressed by using the superimposed pulse bias voltage without increasing the deposition temperature. Different metallizations (Cr and Cu) produced by arc and sputter ion plating are investigated. Carbon-fibre-reinforced epoxy are coated with PVD copper films for further treatment in electrochemical processes. (orig.)

Secondary Electron Emission Yields from PEP-II Accelerator Materials

International Nuclear Information System (INIS)

Kirby, Robert E.

2000-01-01

The PEP-II B-Factory at SLAC operates with aluminum alloy and copper vacuum chambers, having design positron and electron beam currents of 2 and 1 A, respectively. Titanium nitride coating of the aluminum vacuum chamber in the arcs of the positron ring is needed in order to reduce undesirable electron-cloud effects. The total secondary electron emission yield of TiN-coated aluminum alloy has been measured after samples of beam chamber material were exposed to air and again after electron-beam bombardment, as a function of incident electron beam angle and energy. The results may be used to simulate and better understand electron-cloud effects under actual operating conditions. We also present yield measurements for other accelerator materials because new surface effects are expected to arise as beam currents increase. Copper, in particular, is growing in popularity for its good thermal conductivity and self-radiation-shielding properties. The effect of electron bombardment, ''conditioning'', on the yield of TiN and copper is shown

Studies on radiation-sensitive nonsilver halide materials, (1)

International Nuclear Information System (INIS)

Komizu, Hideo; Honda, Koichi; Yabe, Akira; Kawasaki, Masami; Fujii, Etsuo

1978-01-01

In order to discover new radiation-sensitive nonsilver halide materials, the coloration based on the formation of Stenhouse salts was studied in the following three systems: (a) furfural-amine/HCl aq/methanol solution, (b) furfural-amine/polyhalogenide/PMMA matrix, (c) furfural-amine/PVC matrix. Firstly, forty-five aromatic amines were surveyed to find out the amines suitable for the color precursors (reactant from furfural and amine) in the system (a). As a result, the five amines, which gave the precursors in good yields by the reaction with furfural, were selected: m-nitroaniline, N-methylaniline, m-methyl-N-methylaniline, aniline, and o-methoxyaniline. Secondly, the coloration induced by electron beam bombardment was studied in the systems (b) and (c) containing the color precursors (the reactants from these amines and furfural). Although the PMMA films containing the color precursors and polyhalogenides were sensitive to electron beam, they were not stable when standing under daylight at room temperature. The PVC films containing the color precursors were very stable and colored to reddish yellow (lambda sub(max) 498 - 545 nm) by electron beam bombardment. The PVC film containing N-methylaniline-furfural was the most sensitive and the increase in absorbance at 498 nm was 0.78 by electron beam bombardment of 60 kV - 7.5 x 10 -7 C/cm 2 . A good linear relationship existed between the degree of coloration and the amounts of electron beam bombardment in the range from 0 to 10 -6 C/cm 2 . (author)

Production and Evaluation of 236gNp and Reference Materials for Naturally Occurring Radioactive Materials

Science.gov (United States)

Larijani, Cyrus Kouroush

This thesis is based on the development of a radiochemical separation scheme capable of separating both 236gNp and 236Pu from a uranium target of natural isotopic composition ( 1 g uranium) and 200 MBq of fission decay products. The isobaric distribution of fission residues produced following the bombardment of a natural uranium target with a beam of 25 MeV protons has been evaluated. Decay analysis of thirteen isobarically distinct fission residues were carried out using high-resolution gamma-ray spectrometry at the UK National Physical Laboratory. Stoichiometric abundances were calculated via the determination of absolute activity concentrations associated with the longest-lived members of each isobaric chain. This technique was validated by computational modelling of likely sequential decay processes through an isobaric decay chain. The results were largely in agreement with previously published values for neutron bombardments on natural uranium at energies of 14 MeV. Higher relative yields of products with mass numbers A 110-130 were found, consistent with the increasing yield of these radionuclides as the bombarding energy is increased. Using literature values for the production cross-section for fusion of protons with uranium targets, it is estimated that an upper limit of approximately 250 Bq of activity from the 236Np ground state was produced in this experiment. Using a radiochemical separation scheme, Np and Pu fractions were separated from the produced fission decay products, with analyses of the target-based final reaction products made using Inductively Couple Plasma Mass Spectrometry (ICP-MS) and high-resolution alpha and gamma-ray spectrometry. In a separate research theme, reliable measurement of Naturally Occurring Radioactive Materials is of significance in order to comply with environmental regulations and for radiological protection purposes. The thesis describes the standardisation of three reference materials, namely Sand, Tuff and TiO2 which

Experiments on secondary ion emission with multicharged keV ion bombardement

International Nuclear Information System (INIS)

Della Negra, S.; Depauw, J.; Joret, H.; Le Beyec, Y.; Schweikert, E.A.

1987-01-01

An electron cyclotron resonance ion source was used to study the influence of the incident charge state of keV ions on secondary ion emission. The experiments were run with 18 keV Arn+ (1 < n < 11) beams produced by a minimafios source. Various types of targets were bombarded by the ion beam and the sputtered ionized species were identified by time of flight mass spectrometry. The experimental arrangement is detailed and preliminary results are indicated

Modeling the reduction of gross lithium erosion observed under high-flux deuterium bombardment

NARCIS (Netherlands)

Abrams, T.; Jaworski, M. A.; Kaita, R.; Nichols, J. H.; Stotler, D. P.; De Temmerman, G.; van den Berg, M. A.; van der Meiden, H. J.; Morgan, T. W.

2015-01-01

Abstract Both thin (<1 μm) and thick (∼500 μm) lithium films under high-flux deuterium and neon plasma bombardment were studied in the linear plasma device Magnum-PSI at ion fluxes >1024 m−2 s−1 and surface temperatures <700 °C.

Block Play: Practical Suggestions for Common Dilemmas

Science.gov (United States)

Tunks, Karyn Wellhousen

2009-01-01

Learning materials and teaching methods used in early childhood classrooms have fluctuated greatly over the past century. However, one learning tool has stood the test of time: Wood building blocks, often called unit blocks, continue to be a source of pleasure and learning for young children at play. Wood blocks have the unique capacity to engage…

A note on the random walk theory of recoil movement in prolonged ion bombardment

International Nuclear Information System (INIS)

Koponen, Ismo

1994-01-01

A characteristic function is derived for the probability distribution of final positions of recoil atoms in prolonged ion bombardment of dense matter. The derivation is done within the framework of Poissonian random walk theory using a jump distribution, which is somewhat more general than those studied previously. ((orig.))

Effect of ion beam bombardment on the carbide in M2 steel modified by ion-beam-assisted deposition

Energy Technology Data Exchange (ETDEWEB)

Li, X.Y.; Wang, F.J.; Wang, Y.K. (Dept. of Materials Engineering, Dalian Univ. of Technology (China)); Ma, T.C. (National Lab. of Materials Modification by Beam Three, Dalian (China))

1991-10-30

Transmission electron microscopy was used to study the effect of nitrogen ion bombardment with different doses on the carbides in M2 high speed steel as the nitrogen ions penetrated into the nitride films during ion-beam-assisted deposition. With different doses of nitrogen, alterations in the morphological characteristics of the carbide M6C at the interface were observed. With lower doses, knitting-like contrast within the carbide showed subboundary structure defects in M6C. With increasing dose, the substructure defects were broken up into small fragments owing to heavy bombardment. The microstructures of carbides at the interface damaged by nitrogen ions are discussed in detail. (orig.).

21 CFR 882.1925 - Ultrasonic scanner calibration test block.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ultrasonic scanner calibration test block. 882... Ultrasonic scanner calibration test block. (a) Identification. An ultrasonic scanner calibration test block is a block of material with known properties used to calibrate ultrasonic scanning devices (e.g., the...

Thermal-stress analysis of HTGR fuel and control rod fuel blocks in in-block carbonization and annealing furnace

International Nuclear Information System (INIS)

Gwaltney, R.C.; McAfee, W.J.

1977-01-01

A new method for performing thermal stress analyses in structures with multiple penetrations was applied to these analyses. This method couples the development of an equivalent thermal conductivity for the blocks, a technique that has been used extensively for modeling the thermal characteristics of reactor cores, with the use of the equivalent solid plate method for stress analysis. Using this equivalent thermal conductivity, which models as one material the heat transfer characteristics of the fuel, coolant, and graphite two-dimensional, steady-state thermal analyses of the fuel and control rod fuel blocks were performed to establish all temperature boundaries required for the stress analyses. In applying the equivalent solid plate method, the region of penetrations being modeled was replaced by a pseudo material having the same dimensions but whose materials properties were adjusted to account for the penetration. The peak stresses and strains were determined by applying stress and strain intensification factors to the calculated distributions. The condition studied was where the blocks were located near the center of the furnace. In this position, the axial surface of the block is heated near one end and cooled near the other. The approximate axial surface temperatures ranged from 1521 0 C at both the heated and the cooled ends to a peak of 1800 0 C near the center. Five specific cases were analyzed: plane (two-dimensional thermal, plane stress strain) analyses of each end of a standard fuel block (2 cases), plane analyses of each end of a control rod fuel block (2 cases), and a two-dimensional analysis of a fuel block treated as an axisymmetric cylind

Ion beam modification of biological materials in nanoscale

Science.gov (United States)

Yu, L. D.; Anuntalabhochai, S.

2012-07-01

Ion interaction with biological objects in nanoscale is a novel research area stemming from applications of low-energy ion beams in biotechnology and biomedicine. Although the ion beam applications in biotechnology and biomedicine have achieved great successes, many mechanisms remain unclear and many new applications are to be explored. We have carried out some research on exploring the mechanisms and new applications besides attaining ion beam induction of mutation breeding and gene transformation. In the studies on the mechanisms, we focused our investigations on the direct interaction in nanoscale between ions and biological living materials. Our research topics have included the low-energy ion range in DNA, low-energy ion or neutral beam bombardment effect on DNA topological form change and mutation, low-energy ion or neutral beam bombardment effect on the cell envelope and gene transformation, and molecular dynamics simulation of ultra-low-energy ion irradiation of DNA. In the exploration of new applications, we have started experiments on ion irradiation or bombardment, in the nanoscaled depth or area, of human cells for biomedical research. This paper introduces our experiments and reports interesting results.

Ion beam modification of biological materials in nanoscale

International Nuclear Information System (INIS)

Yu, L.D.; Anuntalabhochai, S.

2012-01-01

Ion interaction with biological objects in nanoscale is a novel research area stemming from applications of low-energy ion beams in biotechnology and biomedicine. Although the ion beam applications in biotechnology and biomedicine have achieved great successes, many mechanisms remain unclear and many new applications are to be explored. We have carried out some research on exploring the mechanisms and new applications besides attaining ion beam induction of mutation breeding and gene transformation. In the studies on the mechanisms, we focused our investigations on the direct interaction in nanoscale between ions and biological living materials. Our research topics have included the low-energy ion range in DNA, low-energy ion or neutral beam bombardment effect on DNA topological form change and mutation, low-energy ion or neutral beam bombardment effect on the cell envelope and gene transformation, and molecular dynamics simulation of ultra-low-energy ion irradiation of DNA. In the exploration of new applications, we have started experiments on ion irradiation or bombardment, in the nanoscaled depth or area, of human cells for biomedical research. This paper introduces our experiments and reports interesting results.

Probabilities of symmetric and asymmetric fission in the proton bombardment of Th{sup 232}

Energy Technology Data Exchange (ETDEWEB)

Bowles, B J [Atomic Energy Research Establishment, Chemistry Div., Harwell (United Kingdom); Brown, F; Butler, J P

1957-08-01

The ratio of symmetric to asymmetric fission in the proton bombardment of Th{sup 232} does not rise steadily with increasing proton energy; a periodic decrease in superposed upon the over-all increase. This is attributed to the changing pattern of various fission reactions, (p,f), (p,nf), etc. (author)

Erosion of lithium coatings on TZM molybdenum and graphite during high-flux plasma bombardment

NARCIS (Netherlands)

Abrams, T.; Jaworski, M. A.; Kaita, R.; Stotler, D. P.; De Temmerman, G.; Morgan, T. W.; van den Berg, M. A.; van der Meiden, H. J.

2014-01-01

Abstract The rate at which Li films will erode under plasma bombardment in the NSTX-U divertor is currently unknown. It is important to characterize this erosion rate so that the coatings can be replenished before they are completely depleted. An empirical formula for the Li erosion rate as a

Block copolymer-nanoparticle hybrid self-assembly

KAUST Repository

Hoheisel, Tobias N.; Hur, Kahyun; Wiesner, Ulrich B.

2015-01-01

© 2014 Published by Elsevier Ltd. Polymer-inorganic hybrid materials provide exciting opportunities as they may display favorable properties from both constituents that are desired in applications including catalysis and energy conversion and storage. For the preparation of hybrid materials with well-defined morphologies, block copolymer-directed nanoparticle hybrids present a particularly promising approach. As will be described in this review, once the fundamental characteristics for successful nanostructure formation at or close to the thermodynamic equilibrium of these nanocomposites are identified, the approach can be generalized to various materials classes. In addition to the discussion of recent materials developments based on the use of AB diblock copolymers as well as ABC triblock terpolymers, this review will therefore emphasize progress in the fundamental understanding of the underlying formation mechanisms of such hybrid materials. To this end, critical experiments for, as well as theoretical progress in the description of these nanostructured block copolymer-based hybrid materials will be discussed. Rather than providing a comprehensive overview, the review will emphasize work by the Wiesner group at Cornell University, US, on block copolymer-directed nanoparticle assemblies as well as their use in first potential application areas. The results provide powerful design criteria for wet-chemical synthesis methodologies for the generation of functional nanomaterials for applications ranging from microelectronics to catalysis to energy conversion and storage.

Block copolymer battery separator

Science.gov (United States)

Wong, David; Balsara, Nitash Pervez

2016-04-26

The invention herein described is the use of a block copolymer/homopolymer blend for creating nanoporous materials for transport applications. Specifically, this is demonstrated by using the block copolymer poly(styrene-block-ethylene-block-styrene) (SES) and blending it with homopolymer polystyrene (PS). After blending the polymers, a film is cast, and the film is submerged in tetrahydrofuran, which removes the PS. This creates a nanoporous polymer film, whereby the holes are lined with PS. Control of morphology of the system is achieved by manipulating the amount of PS added and the relative size of the PS added. The porous nature of these films was demonstrated by measuring the ionic conductivity in a traditional battery electrolyte, 1M LiPF.sub.6 in EC/DEC (1:1 v/v) using AC impedance spectroscopy and comparing these results to commercially available battery separators.

Low-energy ion bombardment to tailor the interfacial and mechanical properties of polycrystalline 3C-silicon carbide

International Nuclear Information System (INIS)

Liu Fang; Li, Carolina H.; Pisano, Albert P.; Carraro, Carlo; Maboudian, Roya

2010-01-01

Low-energy Ar + ion bombardment of polycrystalline 3C-silicon carbide (poly-SiC) films is found to be a promising surface modification method to tailor the mechanical and interfacial properties of poly-SiC. The film average stress decreases as the ion energy and the bombardment time increase. Furthermore, this treatment is found to change the strain gradient of the films from positive to negative values. The observed changes in stress and strain gradient are explained by ion peening and thermal spikes models. In addition, the poly-SiC films show a significant enhancement in corrosion resistance by this treatment, which is attributed to a reduction in surface energy and to an increase in the compressive stress in the near-surface region.

Effects of particle size, helium gas pressure and microparticle dose on the plasma concentration of indomethacin after bombardment of indomethacin-loaded poly-L-lactic acid microspheres using a Helios gun system.

Science.gov (United States)

Uchida, Masaki; Natsume, Hideshi; Kobayashi, Daisuke; Sugibayashi, Kenji; Morimoto, Yasunori

2002-05-01

We investigated the effects of the particle size of indomethacin-loaded poly-L-lactic acid microspheres (IDM-loaded PLA MS), the helium pressure used to accelerate the particles, and the bombardment dose of PLA MS on the plasma concentration of IDM after bombarding with IDM-loaded PLA MS of different particle size ranges, 20-38, 44-53 and 75-100 microm, the abdomen of hairless rats using the Helios gene gun system (Helios gun system). Using larger particles and a higher helium pressure, produced an increase in the plasma IDM concentration and the area under the plasma concentration-time curve (AUC) and resultant F (relative bioavailability with respect to intracutaneous injection) of IDM increased by an amount depending on the particle size and helium pressure. Although a reduction in the bombardment dose led to a decrease in C(max) and AUC, F increased on decreasing the bombardment dose. In addition, a more efficient F was obtained after bombarding with IDM-loaded PLA MS of 75-100 microm in diameter at each low dose in different sites of the abdomen compared with that after bolus bombardment with a high dose (dose equivalent). These results suggest that the bombardment injection of drug-loaded microspheres by the Helios gun system is a very useful tool for delivering a variety of drugs in powder form into the skin and systemic circulation.

Rapidity distributions of Ca+Ca, Nb+Nb, Ne+Au and Au+Au at bombarding energies from 250 to 2100 MeV/nucleon

International Nuclear Information System (INIS)

Gutbrod, H.H.; Kolb, B.W.; Schmidt, H.R.; Kampert, K.H.; Poskanzer, A.M.; Ritter, H.G.

1990-02-01

We present experimental rapidity distributions dN ch /dy over a wide range of bombarding energies and projectile and target masses. Target and projectile spectators are observed for peripheral collisions but not for the most central collisions. This behavior is found for all systems and bombarding energies investigated. Although detector inefficiencies tend to distort the experimental distributions, they are on a tolerable level and do not remove sensitivity to theoretical descriptions. (orig.)

The repetitive flaking of Inconel 625 by 100 keV helium bombardment

International Nuclear Information System (INIS)

Whitton, J.L.; Chen, H.M.; Littmark, U.

1981-01-01

Repetitive flaking of Inconel 625 occurs with ion bombardment doses of > than 10 18 100 keV helium ions cm -2 , with up to 39 exfoliations being observed after bombardment with 3 x 10 19 ions cm -2 . The thickness of the flakes, measured by scanning electron microscopy, is some 30% greater than when measured by Rutherford backscattering (RBS) of 1.8 MeV helium ions. These RBS measurements compare well with the thickness of the remaining layers in the resultant craters and to the most probable range of the 100 keV helium. The area of the flakes is dictated by the grain boundaries, and when one flake is ejected, the adjacent grains are prevented from doing so since there now exists an escape route for the injected helium. A strong dose rate dependence is observed; decreasing the beam current from 640 μA cm -2 to 64 μA cm -2 results in a factor 20 fewer flakes being exfoliated (for the same total dose of 3 x 10 19 ions cm -2 ). Successive flakes decrease in area, suggesting that eventually a cratered, but stable, surface will result with the only erosion being by the much less effective mechanism of sputtering. (orig.)

Mineralogical and technology characterization of raw materials of clay used for ceramic blocks fabrication

International Nuclear Information System (INIS)

Campos, N.Q.; Tapajos, N.S.

2012-01-01

In the state of Para, the red ceramic industry has several segments highly generators of jobs and a strong social appeal. With so many companies focused on this productive sector emerge, but many without any administration quality. Therefore, this study focused the technological and mineralogical characterization of the raw material used in the manufacture of ceramic blocks, by Ceramica Vermelha Company, located in the district of Inhangapi-PA. The raw material was obtained by the techniques of X-ray diffraction (XRD) to determine the present crystalline phases through an accurate and efficient procedure, where it was possible to identify the peaks relating to montmorillonite, illite and kaolinite clay in the sample, and kaolinite and quartz in the sample laterite. Another important result was the absorption of water, with average satisfactory according to the standards. According to a sieve analysis, the laterite the sand fraction showed a greater extent compared to the other, while the clay silt exceeding 80% was found to be too plastic material. The resistance to compression, the results were below the required by the standard, suggesting more accurate test methods. (author)

Experimental investigation of neutron generation in thick target blocks of Pb, Hg and W with 0.4 to 2.5 GeV proton beams

International Nuclear Information System (INIS)

Jahnke, U.; Enke, M.; Filges, D.

2002-01-01

Detailed experimental neutron data relevant to the design of the target station of neutron spallation sources have been gathered by the NESSI-collaboration at the COSY accelerator in FZ Juelich. Numerous neutron multiplicity distributions and reaction probabilities have been measured for 0.4 to 2.5 GeV protons bombarding highly segmented target blocks from Pb, Hg and W of up to 35 cm in length and 15 cm in diameter with the intention to provide a comprehensive data base for the improvement and validation of existing reaction simulation codes. (author)

Accelerator-driven neutron sources for materials research

International Nuclear Information System (INIS)

Jameson, R.A.

1990-01-01

Particle accelerators are important tools for materials research and production. Advances in high-intensity linear accelerator technology make it possible to consider enhanced neutron sources for fusion material studies or as a source of spallation neutrons. Energy variability, uniformity of target dose distribution, target bombardment from multiple directions, time-scheduled dose patterns, and other features can be provided, opening new experimental opportunities. New designs have also been used to ensure hands-on maintenance on the accelerator in these factory-type facilities. Designs suitable for proposals such as the Japanese Energy-Selective Intense Neutron Source, and the international Fusion Materials Irradiation Facility are discussed

Angular and energy dependence of ion bombardment of Mo/Si multilayers

DEFF Research Database (Denmark)

Voorma, H.J.; Louis, E.; Bijkerk, F.

1997-01-01

The process of ion bombardment is investigated for the fabrication of Mo/Si multilayer x-ray mirrors using e-beam evaporation. The ion treatment is applied immediately after deposition of each of the Si layers to smoothen the layers by removing an additional thickness of the Si layer. In this stu......, the angular dependence of the etch yield, obtained from the in situ reflectivity measurements, is investigated in order o determine the optimal ion beam parameters for the production of multilayer mirrors on curved substrates....

Changes of electronic properties of p-GaN(0 0 0 1) surface after low-energy N+-ion bombardment

Science.gov (United States)

Grodzicki, M.; Mazur, P.; Ciszewski, A.

2018-05-01

The p-GaN(0 0 0 1) crystal with a relatively low acceptor concentration of 5 × 1016 cm-3 is used in these studies, which are carried out in situ under ultrahigh vacuum (UHV) by ultraviolet photoelectron spectroscopy (UPS), X-ray photoelectron spectroscopy (XPS) and low-energy electron diffraction (LEED). The p-GaN(0 0 0 1)-(1 × 1) surface is achieved by thermal cleaning. N+-ion bombardment by a 200 eV ion beam changes the surface stoichiometry, enriches it with nitrogen, and disorders it. Such modified surface layer inverts its semiconducting character from p- into n-type. The electron affinity for the already cleaned p-GaN surface and that just after bombardment shows a shift from 2.2 eV to 3.2 eV, as well as an increase of band bending at the vacuum/surface interface from 1.4 eV to 2.5 eV. Proper post-bombardment heating of the sample restores the initial atomic order of the modified layer, leaving its n-type semiconducting character unchanged. The results of the measurements are discussed based on two types of surface states concepts.

Systematic analysis of neutron yields from thick targets bombarded by heavy ions and protons with moving source model

Energy Technology Data Exchange (ETDEWEB)

Kato, Takashi; Kurosawa, Tadahiro; Nakamura, Takashi E-mail: nakamura@cyric.tohoku.ac.jp

2002-03-21

A simple phenomenological analysis using the moving source model has been performed on the neutron energy spectra produced by bombarding thick targets with high energy heavy ions which have been systematically measured at the Heavy-Ion Medical Accelerator (HIMAC) facility (located in Chiba, Japan) of the National Institute of Radiological Sciences (NIRS). For the bombardment of both heavy ions and protons in the energy region of 100-500 MeV per nucleon, the moving source model incorporating the knock-on process could be generally successful in reproducing the measured neutron spectra within a factor of two margin of accuracy. This phenomenological analytical equation is expressed having several parameters as functions of atomic number Z{sub p}, mass number A{sub p}, energy per nucleon E{sub p} for projectile, and atomic number Z{sub T}, mass number A{sub T} for target. By inputting these basic data for projectile and target into this equation we can easily estimate the secondary neutron energy spectra at an emission angle of 0-90 deg. for bombardment with heavy ions and protons in the aforementioned energy region. This method will be quite useful to estimate the neutron source term in the neutron shielding design of high energy proton and heavy ion accelerators.

MWTF jumper connector integral seal block development and leak testing

International Nuclear Information System (INIS)

Ruff, E.S.; Jordan, S.R.

1995-01-01

In fiscal year 1993, tests of an o-ring/tetraseal retainer designed to replace a gasket-type seal used in PUREX-type process jumper connectors encouraged the design of an improved seal block. This new seal block combines several parts into one unitized component called an integral seal block. This report summarizes development and leak testing of the new integral seal block. The integral seal block uses a standard o-ring nested in a groove to accomplish leak tightness. This seal block eliminates the need to machine acme threads into the lower skirt casting and seal retainers, eliminates tolerance stack-up, reduces parts inventory, and eliminates an unnecessary leak path in the jumper connector assembly. This report also includes test data on various types of o-ring materials subjected to heat and pressure. Materials tested included Viton, Kalrez, and fluorosilicone, with some incidental data on teflon coated silicone o-rings. Test experience clearly demonstrates the need to test each seal material for temperature and pressure in its intended application. Some materials advertised as being open-quotes betterclose quotes at higher temperatures did not perform up to expectations. Inspection of the fluorosilicone and Kalrez seals after thermal testing indicates that they are much more susceptible to heat softening than Viton

Effects of uranium bombardment by 20-40 KeV argon ions, Annex 2

International Nuclear Information System (INIS)

Nenadovic, T.; Jurela, Z.

1966-01-01

This paper shows the results of argon ions interaction with the polycrystal natural uranium. Thin foil of uranium about 200 μ was bombarded by 20-40 KeV argon ions. Coefficients of cathode scattering δ and secondary electrons emission γ were measured, during the process A + →U. The foil was then studied by transmission method and method of single step replica using an electron microscope [sr

Modelling and simulation of surface morphology driven by ion bombardment

Energy Technology Data Exchange (ETDEWEB)

Yewande, E.O.

2006-05-02

Non-equilibrium surfaces, at nanometer length scales, externally driven via bombardment with energetic particles are known to exhibit well ordered patterns with a variety of applications in nano-technology. These patterns emerge at time scales on the order of minutes. Continuum theory has been quite successful in giving a general picture of the processes that interplay to give the observed patterns, as well as how such competition might determine the properties of the nanostructures. However, continuum theoretical descriptions are ideal only in the asymptotic limit. The only other theoretical alternative, which happens to be more suitable for the characteristic length-and time-scales of pattern formation, is Monte Carlo simulation. In this thesis, surface morphology is studied using discrete solid-on-solid Monte Carlo models of sputtering and surface diffusion. The simulations are performed in the context of the continuum theories and experiments. In agreement with the experiments, the ripples coarsen with time and the ripple velocity exhibits a power-law behaviour with the ripple wavelength, in addition, the exponent was found to depend on the simulation temperature, which suggests future experimental studies of flux dependence. Moreover, a detailed exploration of possible topographies, for different sputtering conditions, corresponding to different materials, was performed. And different surface topographies e.g. holes, ripples, and dots, were found at oblique incidence, without sample rotation. With sample rotation no new topography was found, its only role being to destroy any inherent anisotropy in the system. (orig.)

An efficient, block-by-block algorithm for inverting a block tridiagonal, nearly block Toeplitz matrix

International Nuclear Information System (INIS)

Reuter, Matthew G; Hill, Judith C

2012-01-01

We present an algorithm for computing any block of the inverse of a block tridiagonal, nearly block Toeplitz matrix (defined as a block tridiagonal matrix with a small number of deviations from the purely block Toeplitz structure). By exploiting both the block tridiagonal and the nearly block Toeplitz structures, this method scales independently of the total number of blocks in the matrix and linearly with the number of deviations. Numerical studies demonstrate this scaling and the advantages of our method over alternatives.

Effect of Phase Change Materials (PCMs Integrated into a Concrete Block on Heat Gain Prevention in a Hot Climate

Directory of Open Access Journals (Sweden)

Ahmad Hasan

2016-10-01

Full Text Available In the current study, a phase change material (PCM contained in an insulated concrete block is tested in extremely hot weather in the United Arab Emirates (UAE to evaluate its cooling performance. An insulated chamber is constructed behind the block containing PCM to mimic a scaled down indoor space. The effect of placement of the PCM layer on heat gain indoors is studied at two locations: adjacent to the outer as well as the inner concrete layer. The inclusion of PCM reduced heat gain through concrete blocks compared to blocks without PCM, yielding a drop in cooling load indoors. The placement of PCM and insulation layers adjacent to indoors exhibited better cooling performance compared to that adjacent to the outdoors. In the best case, a temperature drop of 8.5% and a time lag of 2.6 h are achieved in peak indoor temperature, rendering a reduction of 44% in the heat gain. In the tested hot climate, the higher ambient temperature and the lower wind speed hampered heat dissipation and PCM re-solidification by natural ventilation. The findings recommend employing a mechanical ventilation in hot climates to enhance regeneration of the PCM to solid state for its optimal performance.

Hybrid Silicon-Based Organic/Inorganic Block Copolymers with Sol-Gel Active Moieties: Synthetic Advances, Self-Assembly and Applications in Biomedicine and Materials Science.

Science.gov (United States)

Czarnecki, Sebastian; Bertin, Annabelle

2018-03-07

Hybrid silicon-based organic/inorganic (multi)block copolymers are promising polymeric precursors to create robust nano-objects and nanomaterials due to their sol-gel active moieties via self-assembly in solution or in bulk. Such nano-objects and nanomaterials have great potential in biomedicine as nanocarriers or scaffolds for bone regeneration as well as in materials science as Pickering emulsifiers, photonic crystals or coatings/films with antibiofouling, antibacterial or water- and oil-repellent properties. Thus, this Review outlines recent synthetic efforts in the preparation of these hybrid inorganic/organic block copolymers, gives an overview of their self-assembled structures and finally presents recent examples of their use in the biomedical field and material science. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Block copolymer based composition and morphology control in nanostructured hybrid materials for energy conversion and storage: solar cells, batteries, and fuel cells

KAUST Repository

Orilall, M. Christopher; Wiesner, Ulrich

2011-01-01

to materials design and current limitations, the review will highlight some of the most recent examples of block copolymer structure-directed nanomaterials for photovoltaics, batteries and fuel cells. In each case insights are provided into the various

Concrete Waste as a Cement Replacement Material in Concrete Blocks for Optimization of Thermal and Mechanical Properties

OpenAIRE

Rosman M.S.; Abas N.F.; Othuman Mydin M.A.

2014-01-01

The sustainability of the natural environment and eco-systems is of great importance. Waste generated from construction forces mankind to find new dumping grounds and at the same time, more natural resources are required for use as construction materials. In order to overcome this problem, this study was conducted to investigate the use of concrete waste in concrete blocks with a special focus on the thermal and mechanical properties of the resulting products. Three varieties of concrete mixt...

Polymer-Block-Polypeptides and Polymer-Conjugated Hybrid Materials as Stimuli-Responsive Nanocarriers for Biomedical Applications.

Science.gov (United States)

John, Johnson V; Johnson, Renjith P; Heo, Min Seon; Moon, Byeong Kyu; Byeon, Seong Jin; Kim, Il

2015-01-01

Stimuli-responsive nanocarriers are a class of soft materials that includes natural polymers, synthetic polymers, and polypeptides. Recently, modern synthesis tools such as atom transfer radical polymerization, reversible addition-fragmentation chain transfer polymerization, nitroxide-mediated radical polymerization, ring-opening polymerization of α-amino acid N-carboxyanhydrides, and various "click" chemistry strategies were simultaneously employed for the design and synthesis of nanosized drug delivery vehicles. Importantly, the research focused on the improvement of the nanocarrier targetability and the site-specific, triggered release of therapeutics with high drug loading efficiency and minimal drug leakage during the delivery to specific targets. In this context, nanocarriers responsive to common stimuli such as pH, temperature, redox potential, light, etc. have been widely used for the controlled delivery of therapeutics to pathological sites. Currently, different synthesis and self-assembly strategies improved the drug loading efficacy and targeted delivery of therapeutic agents to the desired site. In particular, polypeptide-containing hybrid materials have been developed for the controlled delivery of therapeutic agents. Therefore, stimuli-sensitive synthetic polypeptide-based materials have been extensively investigated in recent years. This review focuses on recent advances in the development of polymer-block-polypeptides and polymer-conjugated hybrid materials that have been designed and evaluated for various stimuli-responsive drug and gene delivery applications.

A Unique Photon Bombardment System for Space Applications

Science.gov (United States)

Klein, E. J.

1993-01-01

The innovative Electromagnetic Radiation Collection and Concentration System (EMRCCS) described is the foundation for the development of a multiplicity of space and terrestrial system formats. The system capability allows its use in the visual, infrared, and ultraviolet ranges of the spectrum for EM collection, concentration, source/receptor tracking, and targeting. The nonimaging modular optical system uses a physically static position aperture for EM radiation collection. Folded optics provide the concentration of the radiation and source autotracking. The collected and concentrated electromagnetic radiation is utilized in many applications, e.g., solar spectrum in thermal and associative photon bombardment applications for hazardous waste management, water purification, metal hardening, hydrogen generation, photovoltaics, etc., in both space and terrestrial segment utilization. Additionally, at the high end of the concentration capability range, i.e., 60,000+, a solar-pulsed laser system is possible.

Removal of foreign atoms from a metal surface bombarded with fast atomic particles

Energy Technology Data Exchange (ETDEWEB)

Dolotov, S.K.; Evstigneev, S.A.; Luk' yanov, S.Yu.; Martynenko, Yu.V.; Chicherov, V.M.

1976-07-01

A metal surface coated with foreign atoms was irradiated with periodically repeating ion current pulses. The energy of the ions bombarding the target was 20 to 30 keV, and inert gas ions were used. A study of the time dependences of the current of the dislodged foreign atoms showed that the rate of their removal from the target surface is determined by the sputtering coefficient of the substrate metal.

Removal of foreign atoms from a metal surface bombarded with fast atomic particles

International Nuclear Information System (INIS)

Dolotov, S.K.; Evstigneev, S.A.; Luk'yanov, S.Yu.; Martynenko, Yu.V.; Chicherov, V.M.

A metal surface coated with foreign atoms was irradiated with periodically repeating ion current pulses. The energy of the ions bombarding the target was 20 to 30 keV, and inert gas ions were used. A study of the time dependences of the current of the dislodged foreign atoms showed that the rate of their removal from the target surface is determined by the sputtering coefficient of the substrate metal

Arthroscopic medial meniscus trimming or repair under nerve blocks: Which nerves should be blocked?

Science.gov (United States)

Taha, AM; Abd-Elmaksoud, AM

2016-01-01

Background: This study aimed to determine the role of the sciatic and obturator nerve blocks (in addition to femoral block) in providing painless arthroscopic medial meniscus trimming/repair. Materials and Methods: One hundred and twenty patients with medial meniscus tear, who had been scheduled to knee arthroscopy, were planned to be included in this controlled prospective double-blind study. The patients were randomly allocated into three equal groups; FSO, FS, and FO. The femoral, sciatic, and obturator nerves were blocked in FSO groups. The femoral and sciatic nerves were blocked in FS group, while the femoral and obturator nerves were blocked in FO group. Intraoperative pain and its causative surgical maneuver were recorded. Results: All the patients (n = 7, 100%) in FO group had intraoperative pain. The research was terminated in this group but completed in FS and FSO groups (40 patients each). During valgus positioning of the knee for surgical management of the medial meniscus tear, the patients in FS group experienced pain more frequently than those in FSO group (P = 0.005). Conclusion: Adding a sciatic nerve block to the femoral nerve block is important for painless knee arthroscopy. Further adding of an obturator nerve block may be needed when a valgus knee position is required to manage the medial meniscus tear. PMID:27375382

AES, EELS and TRIM simulation method study of InP(100 subjected to Ar+, He+ and H+ ions bombardment.

Directory of Open Access Journals (Sweden)

Abidri B.

2012-06-01

Full Text Available Auger Electron Spectroscopy (AES and Electron Energy Loss Spectroscopy (EELS have been performed in order to investigate the InP(100 surface subjected to ions bombardment. The InP(100 surface is always contaminated by carbon and oxygen revealed by C-KLL and O-KLL AES spectra recorded just after introduction of the sample in the UHV spectrometer chamber. The usually cleaning process of the surface is the bombardment by argon ions. However, even at low energy of ions beam (300 eV indium clusters and phosphorus vacancies are usually formed on the surface. The aim of our study is to compare the behaviour of the surface when submitted to He+ or H+ ions bombardment. The helium ions accelerated at 500V voltage and for 45 mn allow removing contaminants but induces damaged and no stoichiometric surface. The proton ions were accelerated at low energy of 500 eV to bombard the InP surface at room temperature. The proton ions broke the In-P chemical bonds to induce the formation of In metal islands. Such a chemical reactivity between hydrogen and phosphorus led to form chemical species such as PH and PH3, which desorbed from the surface. The chemical susceptibly and the small size of H+ advantaged their diffusion into bulk. Since the experimental methods alone were not able to give us with accuracy the disturbed depth of the target by these ions. We associate to the AES and EELS spectroscopies, the TRIM (Transport and Range of Ions in Matter simulation method in order to show the mechanism of interaction between Ar+, He+ or H+ ions and InP and determine the disturbed depth of the target by argon, helium or proton ions.

Strength and deformability of hollow concrete blocks: correlation of block and cylindrical sample test results

Directory of Open Access Journals (Sweden)

C. S. Barbosa

Full Text Available This paper deals with correlations among mechanical properties of hollow blocks and those of concrete used to make them. Concrete hollow blocks and test samples were moulded with plastic consistency concrete, to assure the same material in all cases, in three diferente levels of strength (nominally 10 N/mm², 20 N/mm² and 30 N/mm². The mechanical properties and structural behaviour in axial compression and tension tests were determined by standard tests in blocks and cylinders. Stress and strain analyses were made based on concrete’s modulus of elasticity obtained in the sample tests as well as on measured strain in the blocks’ face-shells and webs. A peculiar stress-strain analysis, based on the superposition of effects, provided an estimation of the block load capacity based on its deformations. In addition, a tentative method to preview the block deformability from the concrete mechanical properties is described and tested. This analysis is a part of a broader research that aims to support a detailed structural analysis of blocks, prisms and masonry constructions.

Material selection for TFTR limiters

International Nuclear Information System (INIS)

Ulrickson, M.

1980-10-01

The requirements for the material to be used as the first surface of limiters in TFTR are that it: (1) withstand a heat flux of 1 kw/cm 2 for a pulse length of 1.5s and a duty cycle of 1/200 for 10 5 cycles, (2) withstand the thermal and electro-magnetic loads from 10 4 plasma current disruptions lasting about 200 μs, (3) generate impurities at a rate low enough to meet impurity control requirements (which depend on the atomic number of the material) for TFTR, and (4) have tritium retention characteristics consistent with tritium inventory requirements for TFTR. An extensive set of material tests using electron beams, neutral beams, and plasma bombardment have been carried out to identify materials which can meet the thermal requirements of the above

CO dissociation and CO hydrogenation on smooth and ion-bombarded Pd(1 1 1): SFG and XPS spectroscopy at mbar pressures

Science.gov (United States)

Rupprechter, G.; Kaichev, V. V.; Unterhalt, H.; Morkel, M.; Bukhtiyarov, V. I.

2004-07-01

The CO dissociation probability on transition metals is often invoked to explain the product distribution (selectivity) of catalytic CO hydrogenation. Along these lines, we have investigated CO adsorption and dissociation on smooth and ion-bombarded Pd(1 1 1) at pressures up to 1 mbar using vibrational sum frequency generation (SFG) and X-ray photoelectron spectroscopy (XPS). Under high pressure, CO adsorbate structures were observed that were identical to high-coverage structures in UHV. On ion-bombarded surfaces an additional species was detected which was attributed to CO bridge bonded to defect (low-coordinated) sites. On both surfaces, no indications of CO dissociation were found even after hours of 0.1 mbar CO exposure. However, exposing CO/H 2 mixtures to ion-bombarded Pd(1 1 1) produced carbonaceous deposits suggesting CH xO species as precursors for CO bond cleavage and that the formation of CH xO is facilitated by surface defects. The relevance of the observations for CO hydrogenation on Pd catalysts is discussed.

CO dissociation and CO hydrogenation on smooth and ion-bombarded Pd(1 1 1): SFG and XPS spectroscopy at mbar pressures

Energy Technology Data Exchange (ETDEWEB)

Rupprechter, G.; Kaichev, V.V.; Unterhalt, H.; Morkel, M.; Bukhtiyarov, V.I

2004-07-31

The CO dissociation probability on transition metals is often invoked to explain the product distribution (selectivity) of catalytic CO hydrogenation. Along these lines, we have investigated CO adsorption and dissociation on smooth and ion-bombarded Pd(1 1 1) at pressures up to 1 mbar using vibrational sum frequency generation (SFG) and X-ray photoelectron spectroscopy (XPS). Under high pressure, CO adsorbate structures were observed that were identical to high-coverage structures in UHV. On ion-bombarded surfaces an additional species was detected which was attributed to CO bridge bonded to defect (low-coordinated) sites. On both surfaces, no indications of CO dissociation were found even after hours of 0.1 mbar CO exposure. However, exposing CO/H{sub 2} mixtures to ion-bombarded Pd(1 1 1) produced carbonaceous deposits suggesting CH{sub x}O species as precursors for C---O bond cleavage and that the formation of CH{sub x}O is facilitated by surface defects. The relevance of the observations for CO hydrogenation on Pd catalysts is discussed.

Effect of N4+ and C4+ ion beam bombardment on the optical and structural characteristics of ethylene-norbornene copolymer (TOPAS)

International Nuclear Information System (INIS)

Siljegovic, M.; Kacarevic-Popovic, Z.M.; Krkljes, A.N.; Stojanovic, Z.; Jovanovic, Z.M.

2011-01-01

Ion bombardment is a suitable tool to modify the optical properties of polymers. In the present study the effect of ion bombardment on the optical absorption of ethylene-norbornene copolymer (TOPAS) was studied using ultraviolet-visible (UV-Vis) and Raman spectroscopy. Polymer samples were bombarded with 60 keV C 4+ and N 4+ ion beams to various fluences ranging from 1.0 x 10 13 to 1.0 x 10 16 cm -2 . The indirect and direct band gaps have been determined. The values of direct band gaps have been found to be greater than the corresponding values of the indirect band gaps. Activation energy has been investigated as the function of ion fluences. The number of carbon atoms per conjugated length is determined according to modified Tauc's equation. The correlation between the optical band gap, activation energy for optical transition and the number of carbon atoms per conjugated length as well as chemical structure changes induced by ion beams irradiation have been discussed in the case of ethylene-norbornene copolymer.

Temperature effect on the formation of a relief of diamond-like carbon coatings and its modification by ion bombardment

International Nuclear Information System (INIS)

Rubshtein, A.P.; Trakhtenberg, I.Sh.; Yugov, V.A.; Vladimirov, A.B.; Plotnikov, S.A.; Ponosov, Yu.S

2006-01-01

Using the method of pulsed arc sputtering of a graphite target the diamond-like coatings (DLC) ∼1.5 μm thick are deposited on a steel R6M5 substrate. The relief of the coatings obtained under various temperature conditions is investigated. Variations of carbon DLC surfaces are followed after their bombardment with accelerated argon or chemically active oxygen ions. Argon ion bombardment is established to be preferred for producing a smoothed-out DLC relief. It is shown that a DLC relief should be taken into account when measuring microhardness. It is recommended that transformation of interatomic bonds in irradiated subsurface layers be taken into consideration if information index of methods applied constitutes several monolayers [ru

Effects of MeV Si ions bombardment on the thermoelectric generator from SiO{sub 2}/SiO{sub 2} + Cu and SiO{sub 2}/SiO{sub 2} + Au nanolayered multilayer films

Energy Technology Data Exchange (ETDEWEB)

Budak, S., E-mail: satilmis.budak@aamu.edu [Department of Electrical Engineering, Alabama A and M University, Normal, AL (United States); Chacha, J., E-mail: chacha_john79@hotmail.com [Department of Electrical Engineering, Alabama A and M University, Normal, AL (United States); Smith, C., E-mail: cydale@cim.aamu.edu [Center for Irradiation of Materials, Alabama A and M University, Normal, AL (United States); Department of Physics, Alabama A and M University, Normal, AL (United States); Pugh, M., E-mail: marcuspughp@yahoo.com [Department of Electrical Engineering, Alabama A and M University, Normal, AL (United States); Colon, T. [Department of Mechanical Engineering, Alabama A and M University, Normal, AL (United States); Heidary, K., E-mail: kaveh.heidary@aamu.edu [Department of Electrical Engineering, Alabama A and M University, Normal, AL (United States); Johnson, R.B., E-mail: barry@w4wb.com [Department of Physics, Alabama A and M University, Normal, AL (United States); Ila, D., E-mail: ila@cim.aamu.edu [Center for Irradiation of Materials, Alabama A and M University, Normal, AL (United States); Department of Physics, Alabama A and M University, Normal, AL (United States)

2011-12-15

The defects and disorder in the thin films caused by MeV ions bombardment and the grain boundaries of these nanoscale clusters increase phonon scattering and increase the chance of an inelastic interaction and phonon annihilation. We prepared the thermoelectric generator devices from 100 alternating layers of SiO{sub 2}/SiO{sub 2} + Cu multi-nano layered superlattice films at the total thickness of 382 nm and 50 alternating layers of SiO{sub 2}/SiO{sub 2} + Au multi-nano layered superlattice films at the total thickness of 147 nm using the physical vapor deposition (PVD). Rutherford Backscattering Spectrometry (RBS) and RUMP simulation have been used to determine the stoichiometry of the elements of SiO{sub 2}, Cu and Au in the multilayer films and the thickness of the grown multi-layer films. The 5 MeV Si ions bombardments have been performed using the AAMU-Center for Irradiation of Materials (CIM) Pelletron ion beam accelerator to make quantum (nano) dots and/or quantum (quantum) clusters in the multilayered superlattice thin films to decrease the cross plane thermal conductivity, increase the cross plane Seebeck coefficient and cross plane electrical conductivity. To characterize the thermoelectric generator devices before and after Si ion bombardments we have measured Seebeck coefficient, cross-plane electrical conductivity, and thermal conductivity in the cross-plane geometry for different fluences.

Capillary condensation in porous materials. Hysteresis and interaction mechanism without pore blocking/percolation process.

Science.gov (United States)

Grosman, Annie; Ortega, Camille

2008-04-15

We have performed measurements of boundary hysteresis loops, reversal curves, and subloops in p+-type porous silicon, a porous material composed of straight non-interconnected pores. These data show that a strong interaction mechanism exists between the pores. The pores of porous silicon are non-independent, whereas they are not interconnected. This hysteretic behavior is very similar to that observed in porous glass, which consists of cavities connected to each other by constrictions. This questions the so-called pore blocking/percolation model developed to explain the behavior of fluid in porous glass. More generally, if we disregard the shape of the boundary hysteresis loops which depends on the porous material (H1 for MCM-41 and SBA-15, H2 for porous glass and p+-type porous silicon), the hysteretic features inside the main loop are qualitatively the same for all these porous systems. This shows that none of these systems are composed of independent pores. A coupling between the pores is always present whether they are interconnected or not and whatever the shape of the main loop is.

A liquid-like model for the morphology evolution of ion bombarded thin films

Energy Technology Data Exchange (ETDEWEB)

Repetto, L., E-mail: luca.repetto@unige.it [Department of Physics and Nanomed Labs, Università di Genova, Via Dodecaneso 33, 16146 Genova (Italy); Lo Savio, R. [Department of Physics and Nanomed Labs, Università di Genova, Via Dodecaneso 33, 16146 Genova (Italy); Šetina Batič, B. [Inštitut Za Kovinske Materiale in Tehnologije, Lepi pot 11, 1000 Ljubljana (Slovenia); Firpo, G.; Angeli, E.; Valbusa, U. [Department of Physics and Nanomed Labs, Università di Genova, Via Dodecaneso 33, 16146 Genova (Italy)

2015-07-01

Thin solid films exposed to ion irradiation exhibit a peculiar evolution that can differ substantially from what is observed for bulk samples. The phenomenology of the patterns that self-organize on the substrate is very rich, with morphologies that display several degrees of order upon the modification of initial film characteristics and irradiation parameters. This richness paves the way for the fabrication of novel functional surfaces, but it is also an indication of the complexity of the underlying driving mechanisms. A remarkable simplification for the comprehension of these phenomena can come from the noteworthy similarity of the obtained patterns with those showing up when liquids dewet from their substrates. Here, we analyze the possibility to apply a liquid-like model to explain the morphology evolution of ion bombarded thin films for the whole phenomenology showing up in experiments. In establishing this connection between liquids and ion bombarded thin films, we propose to use also for liquids the insight gained for our system with recent experiments that stress the importance of the substrate topography for the selection of the dewetting mechanism. If confirmed, this result would lead to a reconsideration of the importance of capillary waves in spinodal dewetting, and will help to understand the low reproducibility of the related experimental results.

Neutron bombardment of single wall carbon nanohorn (SWCNH). DSC determination of the stored Wigner-Szilard energy

International Nuclear Information System (INIS)

Franco Cataldo; Susana Iglesias-Groth; Yaser Hafez; Giancarlo Angelini

2014-01-01

Single wall carbon nanohorn (SWCNH) were neutron-bombarded to a dose of 3.28 × 10 16 n/cm 2 . The Wigner or stored energy was determined by a differential scanning calorimeter and was found 5.49 J/g, 50 times higher than the Wigner energy measured on graphite flakes treated at the same neutron dose. The activation energy for the thermal annealing of the accumulated radiation damage in SWCNH was determined in the range 6.3-6.6 eV against a typical activation energy for the annealing of the radiation-damaged graphite which is in the range of 1.4-1.5 eV. Furthermore the stored energy in neutron-damaged SWCNH is released at 400-430 deg C while the main peak in the neutron-damaged graphite occurs at 200-220 deg C. The radiation damaged SWCNH were examined with FT-IR spectroscopy showing the formation of acetylenic and aliphatic moieties suggesting the aromatic C=C breakdown caused by the neutron bombardment. (author)

Foil analysis of 1.5-GeV proton bombardment of a mercury target

CERN Document Server

Charlton, L A; Glasgow, D C; Gabriel, T A

1999-01-01

The number of reactant nuclei in a series of foils surrounding a container of mercury that has been bombarded by 1.5-GeV protons is calculated and compared with experimental measurements. This procedure is done to aid in the validation of the mercury cross sections used in the design studies of the Spallation Neutron Source (SNS). It is found that the calculations match the measurements to within the uncertainties inherent in the analysis.

Charge generation and trapping in bisphenol-A-polycarbonate/N-isopropylcarbazole mixture: A study by electron bombardment-induced conductivity

International Nuclear Information System (INIS)

Santos, S.; Caraballo, D.

2007-01-01

Electron bombardment-induced conductivity measurements were carried out on cast films of N-isopropylcarbazole (NIPC) dispersed into an amorphous matrix of bisphenol-A-polycarbonate. The charge generation was studied by estimating the hole yield (g), the fraction of charge escaping recombination, as a function of electric field and concentration of NIPC at room temperature. The hole yield, besides increasing by increasing the content of NIPC, was observed to increase with the electric field in the manner predicted by the Onsager theory of geminate recombination. Deep trapping levels were studied by filling under electron bombardment and observing transients. The deep traps were neutral in nature with a concentration on the order of 8.0x10 14 cm -3 , which was low enough not to degrade transport under normal conditions

Reducing Energy Degradation Due to Back-bombardment Effect with Modulated RF Input in S-band Thermionic RF Gun

Science.gov (United States)

Kii, Toshiteru; Nakai, Yoko; Fukui, Toshio; Zen, Heishun; Kusukame, Kohichi; Okawachi, Norihito; Nakano, Masatsugu; Masuda, Kai; Ohgaki, Hideaki; Yoshikawa, Kiyoshi; Yamazaki, Tetsuo

2007-01-01

Energy degradation due to back-bombardment effect is quite serious to produce high-brightness electron beam with long macro-pulse with thermionic rf gun. To avoid the back-bombardment problem, a laser photo cathode is used at many FEL facilities, but usually it costs high and not easy to operate. Thus we have studied long pulse operation of the rf gun with thermionic cathode, which is inexpensive and easy to operate compared to the photocathode rf gun. In this work, to reduce the energy degradation, we controlled input rf power amplitude by controlling pulse forming network of the power modulator for klystron. We have successfully increased the pulse duration up to 4 μs by increasing the rf power from 7.8 MW to 8.5 MW during the macro pulse.

Thermo-responsive block copolymers

NARCIS (Netherlands)

Mocan Cetintas, Merve

2017-01-01

Block copolymers (BCPs) are remarkable materials because of their self-assembly behavior into nano-sized regular structures and high tunable properties. BCPs are in used various applications such as surfactants, nanolithography, biomedicine and nanoporous membranes. In these thesis, we aimed to

Developing Key Parameters for Green Performance of Partition Wall Blocks

Directory of Open Access Journals (Sweden)

Goh Cheng Siew

2016-01-01

Full Text Available To promote sustainable construction, it is important to consider green performance of construction materials throughout the life cycle. Selecting inappropriate materials could not only affect the functional performance but also preclude the achievement of green building performance as a whole. Green performance of construction materials has therefore been one of the primary considerations of green building assessment systems. Using partition wall blocks as an example, this paper examines green performance of building materials primarily from the cradle to gate boundaries. Nine key parameters are proposed for the green performance of partition wall blocks. Apart from environmental features, technical performance of partition wall blocks is also taken into consideration since it is the determinant of the lifecycle performance. This paper offers a roadmap to decision makers to make environmentally responsible choices for their materials of internal walls and partitions, and hence provides a potential sustainable solution for green buildings.

Steam-cured stabilised soil blocks for masonry construction

Energy Technology Data Exchange (ETDEWEB)

Venkatarama Reddy, B.V. [Indian Inst. of Science, Bangalore (India). Dept. of Civil Engineering; Lokras, S.S. [Indian Inst. of Science, Bangalore (India). ASTRA

1998-12-01

Energy-efficient, economical and durable building materials are essential for sustainable construction practices. The paper deals with production and properties of energy-efficient steam-cured stabilised soil blocks used for masonry construction. Problems of mixing expansive soil and lime, and production of blocks using soil-lime mixtures have been discussed briefly. Details of steam curing of stabilised soil blocks and properties of such blocks are given. A comparison of energy content of steam-cured soil blocks and burnt bricks is presented. It has been shown that energy-efficient steam cured soil blocks (consuming 35% less thermal energy compared to burnt clay bricks) having high compressive strength can be easily produced in a decentralised manner. (orig.)

Comments on Auger electron production by Ne/sup +/ bombardment of surfaces

Energy Technology Data Exchange (ETDEWEB)

Pepper, S V; Ferrante, J [National Aeronautics and Space Administration, Cleveland, OH (USA). Lewis Research Center

1979-09-01

In this letter, the authors first report rather conclusive experimental evidence showing that the Ne Auger signal is due to asymmetric Ne-metal collisions and not symmetric Ne-Ne collisions. Next it is shown that the Ne Auger signal is in fact observable by Ne/sup +/ bombardment of Si and with signal strength comparable to that of the Si Auger signal for 3 keV incident ion energy. Finally, they comment on some trends in the relative amplitudes of the 21.9 and 25.1 eV Ne Auger signals as a function of incident ion energy and target species.

A theoretical approach to sputtering due to molecular ion bombardment, 1

International Nuclear Information System (INIS)

Karashima, Shosuke; Ootoshi, Tsukuru; Kamiyama, Masahide; Kim, Pil-Hyon; Namba, Susumu.

1981-01-01

A shock wave model is proposed to explain theoretically the non-linear effects in sputtering phenomena by molecular ion bombardments. In this theory the sputtering processes are separated into two parts; one is due to linear effects and another is due to non-linear effects. The treatment of the linear parts is based on the statistical model by Schwarz and Helms concerning a broad range of atomic collision cascades. The non-linear parts are treated by the model of shock wave due to overlapping cascades, and useful equations to calculate the sputtering yields and the dynamical quantities in the system are derived. (author)

EPR study of electron bombarded alkali- and alkaline-earth halide crystal surfaces

Science.gov (United States)

Fryburg, G. C.; Lad, R. A.

1975-01-01

An EPR study of electron bombarded LiF, NaCl, KCl, CaF2 and BaF2 polycrystalline surfaces has shown that small metal particles are formed on the surfaces of the crystals. Identification was made from CESR signals. The symmetric line-shape of the signals, even at 77 K, indicated that the particles were less than 0.5 micron in diameter. Signals due to F centers were observed in LiF but not in the other halides. Implications to metal deposition are considered.

Study of ion-bombardment-induced surface topography of silver by stereophotogrammetric method

International Nuclear Information System (INIS)

Fayazov, I.M.; Sokolov, V.N.

1992-01-01

The ion-bombardment-induced surface topography of polycrystalline silver was studied using the stereophotogrammetric method. The samples were irradiated with 30keV argon ions at fairly high fluences (> 10 17 ions/cm 2 ). The influence of the inclination angle of the sample in the SEM on the cone shape of a SEM-picture is discussed. To analyse the irradiated surfaces covered with cones, the SEM-stereotechnique is proposed. The measurements of the sample section perpendicular to the incidence plane are also carried out. (author)

Self-assembling block copolymer systems involving competing length scales : A route toward responsive materials

NARCIS (Netherlands)

Nap, R; Erukhimovich, [No Value; ten Brinke, G; Erukhimovich, Igor

2004-01-01

The phase behavior of block copolymers melts involving competing length scales, i.e., able to microphase separate on two different length scales, is theoretically investigated using a self-consistent field approach. The specific block copolymers studied consist of a linear A-block linked to an

Performance of a liquid-junction interface for capillary electrophoresis mass spectrometry using continuous-flow fast-atom bombardment

NARCIS (Netherlands)

Reinhoud, N.J.; Niessen, W.M.A.; Tjaden, U.R.; Gramberg, L.G.; Verheij, E.R.; Greef, J. van der

1989-01-01

The on-line coupling of capillary electrophoresis and mass spectrometry using a continuous-flow fast-atom bombardment system in combination with a liquid-junction interface is described. The influence of the liquid-junction coupling on the efficiency and the resolution is investigated. Qualitative

Heavy-ion induced desorption yields of cryogenic surfaces bombarded with 4.2 MeV/u lead ions

CERN Document Server

Mahner, E; Evans, L; Kollmus, H; Küchler, D; Scrivens, R; Severin, D; Wengenroth, M; CERN. Geneva. ATS Department

2011-01-01

The ion-induced desorption experiment, installed in the CERN Heavy-Ion Accelerator LINAC 3, has been used to study the dynamic outgassing of cryogenic surfaces. Two different targets, bare and goldcoated copper, were bombarded under perpendicular impact with 4.2 MeV/u Pb54+ ions. Partial pressure rises of H2, CH4, CO, and CO2 and effective desorption yields were measured at 300, 77, and 6.3 K using single shot and continuous ion bombardment techniques. We find that the heavy-ion-induced desorption yield is temperature dependent and investigate the influence of CO gas cryosorbed at 6.3 K. The gain in desorption yield reduction at cryogenic temperature vanishes after several monolayers of CO are cryosorbed on both targets. In this paper we describe the new cryogenic target assembly, the temperature-dependent pressure rise, desorption yield, and gas adsorption measurements.

Nanoporous Crosslinked Polyisoprene from Polyisoprene-Polydimethylsiloxane Block Copolymer

DEFF Research Database (Denmark)

Hansen, Michael Steffen; Vigild, Martin Etchells; Berg, Rolf Henrik

2004-01-01

The polyisoprene block of a polyisoprene-polydimethylsiloxane (PI-PDMS) diblock copolymer with 0.68 volume fraction of PI was tightly crosslinked with dicumylperoxide. The PDMS part of the obtained glassy material was subsequently quantitatively etched with anhydrous hydrogen fluoride or tetrabut......The polyisoprene block of a polyisoprene-polydimethylsiloxane (PI-PDMS) diblock copolymer with 0.68 volume fraction of PI was tightly crosslinked with dicumylperoxide. The PDMS part of the obtained glassy material was subsequently quantitatively etched with anhydrous hydrogen fluoride...

Surface Morphologies of Ti and Ti-Al-V Bombarded by 1.0-MeV Au+ Ions

Science.gov (United States)

Garcia, M. A.; Rickards, J.; Cuerno, R.; Trejo-Luna, R.; Cañetas-Ortega, J.; de la Vega, L. R.; Rodríguez-Fernández, L.

2017-12-01

Ion implantation is known to enhance the mechanical properties of biomaterials such as, e.g., the wear resistance of orthopedic joints. Increasing the surface area of implants may likewise improve their integration with, e.g., bone tissue, which requires surface features with sizes in the micron range. Ion implantation of biocompatible metals has recently been demonstrated to induce surface ripples with wavelengths of a few microns. However, the physical mechanisms controlling the formation and characteristics of these patterns are yet to be understood. We bombard Ti and Ti-6Al-4V surfaces with 1.0-MeV Au+ ions. Analysis by scanning electron and atomic force microscopies shows the formation of surface ripples with typical dimensions in the micron range, with potential indeed for biomedical applications. Under the present specific experimental conditions, the ripple properties are seen to strongly depend on the fluence of the implanted ions while being weakly dependent on the target material. Moreover, by examining experiments performed for incidence angle values θ =8 ° , 23°, 49°, and 67°, we confirm the existence of a threshold incidence angle for (ripple) pattern formation. Surface indentation is also used to study surface features under additional values of θ , agreeing with our single-angle experiments. All properties of the surface structuring process are very similar to those found in the production of surface nanopatterns under low-energy ion bombardment of semiconductor targets, in which the stopping power is dominated by nuclear contributions, as in our experiments. We consider a continuum model that combines the effects of various physical processes as originally developed in that context, with parameters that we estimate under a binary-collision approximation. Notably, reasonable agreement with our experimental observations is achieved, even under our high-energy conditions. Accordingly, in our system, ripple formation is determined by mass

Phenomenology of the plastic flow of amorphous solids induced by heavy-ion bombardment

International Nuclear Information System (INIS)

Klaumuenzer, S.; Benyagoub, A.

1991-01-01

Amorphous solids exhibit at temperatures far below the glass transition plastic flow when bombarded with fast heavy ions (kinetic energy ∼1 MeV/u). The dimensions perpendicular to the ion beam grow whereas the sample dimension parallel to the ion beam shrinks. The strain tensor describing phenomenologically these dimensional changes is derived from symmetry considerations and compared with experiment. Particular attention is devoted to angular changes, which have not been discussed in this context so far

Linoleum Block Printing Revisited.

Science.gov (United States)

Chetelat, Frank J.

1980-01-01

The author discusses practical considerations of teaching linoleum block printing in the elementary grades (tool use, materials, motivation) and outlines a sequence of design concepts in this area for the primary, intermediate and junior high grades. A short list of books and audiovisual aids is appended. (SJL)

Gene gun bombardment-mediated expression and translocation of EGFP-tagged GLUT4 in skeletal muscle fibres in vivo

DEFF Research Database (Denmark)

Lauritzen, Hans P M M; Reynet, Christine; Schjerling, Peter

2002-01-01

the enhanced green fluorescent protein (EGFP) labelling technique with physical transfection methods in vivo: intramuscular plasmid injection or gene gun bombardment. During optimisation experiments with plasmid coding for the EGFP reporter alone EGFP-positive muscle fibres were counted after collagenase...... treatment of in vivo transfected flexor digitorum brevis (FDB) muscles. In contrast to gene gun bombardment, intramuscular injection produced EGFP expression in only a few fibres. Regardless of the transfection technique, EGFP expression was higher in muscles from 2-week-old rats than in those from 6-week......Cellular protein trafficking has been studied to date only in vitro or with techniques that are invasive and have a low time resolution. To establish a gentle method for analysis of glucose transporter-4 (GLUT4) trafficking in vivo in fully differentiated rat skeletal muscle fibres we combined...

A novel detector based on dual-mode fiber polished half block's characteristics for sensitive monitorings of radiation and materials

International Nuclear Information System (INIS)

Saeed, Ghadirli

2005-01-01

Full text : The overlay index dependence characteristics of the power distribution between two modes of dual-mode fiber polished half blocks is studied. The heat dependence characteristics of a certain overlay index affects the modal power distributions at the input of interferometer sensors used for monitoring the sensitive heat radiation changes. The other fundamental applications such as material recognitions through the index dependence characteristics in the closed chambers is also suggested

Ultrafast carrier dynamics in Br.sup.+./sup.-bombarded InP studied by time-resolved terahertz spectroscopy

Czech Academy of Sciences Publication Activity Database

Němec, Hynek; Fekete, Ladislav; Kadlec, Filip; Kužel, Petr

2008-01-01

Roč. 78, č. 23 (2008), 235206/1-235206/7 ISSN 1098-0121 R&D Projects: GA MŠk LC512 Institutional research plan: CEZ:AV0Z10100520 Keywords : InP * carrier lifetime * carrier mobility * ultrafast * ion-bombardment * terahertz Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.322, year: 2008

Erosion tests of materials by energetic particle beams

Energy Technology Data Exchange (ETDEWEB)

Schechter, D.E.; Tsai, C.C.; Sluss, F.; Becraft, W.R.; Hoffman, D.J.

1985-01-01

The internal components of magnetic fusion devices must withstand erosion from and high heat flux of energetic plasma particles. The selection of materials for the construction of these components is important to minimize contamination of the plasma. In order to study various materials' comparative resistance to erosion by energetic particles and their ability to withstand high heat flux, water-cooled copper swirl tubes coated or armored with various materials were subjected to bombardment by hydrogen and helium particle beams. Materials tested were graphite, titanium carbide (TiC), chromium, nickel, copper, silver, gold, and aluminum. Details of the experimental arrangement and methods of application or attachment of the materials to the copper swirl tubes are presented. Results including survivability and mass losses are discussed.

Effects of electron blocking and hole trapping of the red guest emitter materials on hybrid white organic light emitting diodes

International Nuclear Information System (INIS)

Hong, Lin-Ann; Vu, Hoang-Tuan; Juang, Fuh-Shyang; Lai, Yun-Jr; Yeh, Pei-Hsun; Tsai, Yu-Sheng

2013-01-01

Hybrid white organic light emitting diodes (HWOLEDs) with fluorescence and phosphorescence hybrid structures are studied in this work. HWOLEDs were fabricated with blue/red emitting layers: fluorescent host material doped with sky blue material, and bipolar phosphorescent host emitting material doped with red dopant material. An electron blocking layer is applied that provides hole red guest emitter hole trapping effects, increases the charge carrier injection quantity into the emitting layers and controls the recombination zone (RZ) that helps balance the device color. Spacer layers were also inserted to expand the RZ, increase efficiency and reduce energy quenching along with roll-off effects. The resulting high efficiency warm white OLED device has the lower highest occupied molecule orbital level red guest material, current efficiency of 15.9 cd/A at current density of 20 mA/cm 2 , and Commission Internationale de L'Eclairage coordinates of (0.34, 0.39)

Effects of electron blocking and hole trapping of the red guest emitter materials on hybrid white organic light emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Hong, Lin-Ann; Vu, Hoang-Tuan [National Formosa University, Institute of Electro-Optical and Materials Science, Huwei, Yunlin County, Taiwan (China); Juang, Fuh-Shyang, E-mail: fsjuang@seed.net.tw [National Formosa University, Institute of Electro-Optical and Materials Science, Huwei, Yunlin County, Taiwan (China); Lai, Yun-Jr [National Formosa University, Institute of Electro-Optical and Materials Science, Huwei, Yunlin County, Taiwan (China); Yeh, Pei-Hsun [Raystar Optronics, Inc., 5F No. 25, Keya Rd. Daya Township, Taichung County, Taiwan (China); Tsai, Yu-Sheng [National Formosa University, Institute of Electro-Optical and Materials Science, Huwei, Yunlin County, Taiwan (China)

2013-10-01

Hybrid white organic light emitting diodes (HWOLEDs) with fluorescence and phosphorescence hybrid structures are studied in this work. HWOLEDs were fabricated with blue/red emitting layers: fluorescent host material doped with sky blue material, and bipolar phosphorescent host emitting material doped with red dopant material. An electron blocking layer is applied that provides hole red guest emitter hole trapping effects, increases the charge carrier injection quantity into the emitting layers and controls the recombination zone (RZ) that helps balance the device color. Spacer layers were also inserted to expand the RZ, increase efficiency and reduce energy quenching along with roll-off effects. The resulting high efficiency warm white OLED device has the lower highest occupied molecule orbital level red guest material, current efficiency of 15.9 cd/A at current density of 20 mA/cm{sup 2}, and Commission Internationale de L'Eclairage coordinates of (0.34, 0.39)

Initial Mechanical Testing of Superalloy Lattice Block Structures Conducted

Science.gov (United States)

Krause, David L.; Whittenberger, J. Daniel

2002-01-01

The first mechanical tests of superalloy lattice block structures produced promising results for this exciting new lightweight material system. The testing was performed in-house at NASA Glenn Research Center's Structural Benchmark Test Facility, where small subelement-sized compression and beam specimens were loaded to observe elastic and plastic behavior, component strength levels, and fatigue resistance for hundreds of thousands of load cycles. Current lattice block construction produces a flat panel composed of thin ligaments arranged in a three-dimensional triangulated trusslike structure. Investment casting of lattice block panels has been developed and greatly expands opportunities for using this unique architecture in today's high-performance structures. In addition, advances made in NASA's Ultra-Efficient Engine Technology Program have extended the lattice block concept to superalloy materials. After a series of casting iterations, the nickel-based superalloy Inconel 718 (IN 718, Inco Alloys International, Inc., Huntington, WV) was successfully cast into lattice block panels; this combination offers light weight combined with high strength, high stiffness, and elevated-temperature durability. For tests to evaluate casting quality and configuration merit, small structural compression and bend test specimens were machined from the 5- by 12- by 0.5-in. panels. Linear elastic finite element analyses were completed for several specimen layouts to predict material stresses and deflections under proposed test conditions. The structural specimens were then subjected to room-temperature static and cyclic loads in Glenn's Life Prediction Branch's material test machine. Surprisingly, the test results exceeded analytical predictions: plastic strains greater than 5 percent were obtained, and fatigue lives did not depreciate relative to the base material. These assets were due to the formation of plastic hinges and the redundancies inherent in lattice block construction

Study and optimisation of SIMS performed with He+ and Ne+ bombardment

International Nuclear Information System (INIS)

Pillatsch, L.; Vanhove, N.; Dowsett, D.; Sijbrandij, S.; Notte, J.; Wirtz, T.

2013-01-01

The combination of the high-brightness He + /Ne + atomic level ion source with the detection capabilities of secondary ion mass spectrometry (SIMS) opens up the prospect of obtaining chemical information with high lateral resolution and high sensitivity on the Zeiss ORION helium ion microscope (HIM). A feasibility study with He + and Ne + ion bombardment is presented in order to determine the performance of SIMS analyses using the HIM. Therefore, the sputtering yields, useful yields and detection limits obtained for metallic (Al, Ni and W) as well as semiconductor samples (Si, Ge, GaAs and InP) were investigated. All the experiments were performed on a Cameca IMS4f SIMS instrument which was equipped with a caesium evaporator and oxygen flooding system. For most of the elements, useful yields in the range of 10 −4 to 3 × 10 −2 were measured with either O 2 or Cs flooding. SIMS experiments performed directly on the ORION with a prototype secondary ion extraction and detection system lead to results that are consistent with those obtained on the IMS4f. Taking into account the obtained useful yields and the analytical conditions, such as the ion current and typical dwell time on the ORION HIM, detection limits in the at% range and better can be obtained during SIMS imaging at 10 nm lateral resolution with Ne + bombardment and down to the ppm level when a lateral resolution of 100 nm is chosen. Performing SIMS on the HIM with a good detection limit while maintaining an excellent lateral resolution (<50 nm) is therefore very promising.

3D imaging by serial block face scanning electron microscopy for materials science using ultramicrotomy.

Science.gov (United States)

Hashimoto, Teruo; Thompson, George E; Zhou, Xiaorong; Withers, Philip J

2016-04-01

Mechanical serial block face scanning electron microscopy (SBFSEM) has emerged as a means of obtaining three dimensional (3D) electron images over volumes much larger than possible by focused ion beam (FIB) serial sectioning and at higher spatial resolution than achievable with conventional X-ray computed tomography (CT). Such high resolution 3D electron images can be employed for precisely determining the shape, volume fraction, distribution and connectivity of important microstructural features. While soft (fixed or frozen) biological samples are particularly well suited for nanoscale sectioning using an ultramicrotome, the technique can also produce excellent 3D images at electron microscope resolution in a time and resource-efficient manner for engineering materials. Currently, a lack of appreciation of the capabilities of ultramicrotomy and the operational challenges associated with minimising artefacts for different materials is limiting its wider application to engineering materials. Consequently, this paper outlines the current state of the art for SBFSEM examining in detail how damage is introduced during slicing and highlighting strategies for minimising such damage. A particular focus of the study is the acquisition of 3D images for a variety of metallic and coated systems. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights reserved.

Application of interconnected porous hydroxyapatite ceramic block for onlay block bone grafting in implant treatment: A case report.

Science.gov (United States)

Ohta, Kouji; Tada, Misato; Ninomiya, Yoshiaki; Kato, Hiroki; Ishida, Fumi; Abekura, Hitoshi; Tsuga, Kazuhiro; Takechi, Masaaki

2017-12-01

Autogenous block bone grafting as treatment for alveolar ridge atrophy has various disadvantages, including a limited availability of sufficiently sized and shaped grafts, donor site morbidity and resorption of the grafted bone. As a result, interconnected porous hydroxyapatite ceramic (IP-CHA) materials with high porosity have been developed and used successfully in orthopedic cases. To the best of the author's knowledge, this is the first report of clinical application of an IP-CHA block for onlay grafting for implant treatment in a patient with horizontal alveolar atrophy. The present study performed onlay block grafting using an IP-CHA block to restore bone volume for implant placement in the alveolar ridge area without collecting autogenous bone. Dental X-ray findings revealed that the border of the IP-CHA block became increasingly vague over the 3-year period, whereas CT scanning revealed that the gap between the block and bone had a smooth transition, indicating that IP-CHA improved the process of integration with host bone. In follow-up examinations over a period of 5 years, the implants and superstructures had no problems. An IP-CHA block may be useful as a substitute for onlay block bone grafting in implant treatment.

Toothbrushing alters the surface roughness and gloss of composite resin CAD/CAM blocks.

Science.gov (United States)

Kamonkhantikul, Krid; Arksornnukit, Mansuang; Lauvahutanon, Sasipin; Takahashi, Hidekazu

2016-01-01

This study investigated the surface roughness and gloss of composite resin CAD/CAM blocks after toothbrushing. Five composite resin blocks (Block HC, Cerasmart, Gradia Block, KZR-CAD Hybrid Resin Block, and Lava Ultimate), one hybrid ceramic (Vita Enamic), one feldspar ceramic (Vitablocs Mark II), one PMMA block (Telio CAD), and one conventional composite resin (Filtek Z350 XT) were evaluated. Surface roughness (Ra) and gloss were determined for each group of materials (n=6) after silicon carbide paper (P4000) grinding, 10k, 20k, and 40k toothbrushing cycles. One-way repeated measures ANOVA indicated significant differences in the Ra and gloss of each material except for the Ra of GRA. After 40k toothbrushing cycles, the Ra of BLO and TEL showed significant increases, while CER, KZR, ULT, and Z350 showed significant decreases. GRA, ENA, and VIT maintained their Ra. All of the materials tested, except CER, demonstrated significant decreases in gloss after 40k toothbrushing cycles.

Ion bombardment induced topography evolution on low index crystal surfaces of Cu and Pb

International Nuclear Information System (INIS)

Tanovic, L.; Tanovic, N.; Carter, G.; Nobes, M.J.

1993-01-01

(100), (110) and (111) oriented single crystal surfaces of Cu and Pb have been bombarded with inert gas ions, self ions, ions of the other substrate species and Bi in the energy range 50-150 keV and in the fluence range 10 15 -10 18 ions.cm 2 . The evolving surface topography was observed by scanning electron microscopy. This topography was observed to be strongly influenced by ion species and surface orientation but the habit of the topography was delineated at low fluences and the features increased in size and density with increasing fluence with some mutation to the more stable of the features. As an example Bi and Pb bombardment of (100) Cu leads to little topographic evolution, (110) Cu develops a system of parallel ridges with (100) facets and (111) Cu develops a prismatic surface, each prism possessing (100) facets. These, and the more general, results cannot be explained by surface erosion by sputtering theory alone (this predicts surface stability of the lowest sputtering yield orientation (110), nor by surface free energy density minimisation criteria (this predicts stability of (111) surfaces). It is proposed that the observed topography is most strongly related to the crystallographic form of precipitates of implanted species. (orig.)

Engine Fundamentals: Automotive Mechanics Instructional Program. Block 2.

Science.gov (United States)

O'Brien, Ralph D.

The second of six instructional blocks in automotive mechanics, the lessons and supportive information in the document provide a guide for teachers in planning an instructional program in engine fundamentals at the secondary and postsecondary level. The material, as organized, is a suggested sequence of instruction within each block. Each lesson…

Evaluation of long-term stability of low thermal expansion coefficient materials using gauge block interferometers

Science.gov (United States)

Hirai, Akiko; Bitou, Youichi; Oike, Yoshiyuki

2018-06-01

The long-term stability of NEXCERA™ ceramics having a low coefficient of thermal expansion was evaluated over a period of eight years. Several gauge blocks of differing lengths were prepared, using two types of NEXCERA. Each gauge block was kept wrung to a platen and its absolute length was periodically measured by gauge block interferometer during the eight years. Relative uncertainties of measurement of changes in gauge block length were estimated as 4.1  ×  10‑8 and 2.9  ×  10‑8 for 200 mm and 800 mm gauge blocks, respectively. The experimental results show the trend of expansion and a relative change of less than 0.1  ×  10‑6/year for every gauge block.

Particle Simulations of a Thermionic RF Gun with Gridded Triode Structure for Reduction of Back-Bombardment

CERN Document Server

Kusukame, K; Kii, T; Masuda, K; Nakai, Y; Ohgaki, H; Yamazaki, T; Yoshikawa, K; Zen, H

2005-01-01

Thermionic RF guns show advantageous features compared with photocathode ones such as easy operation and much higher repetition rate of micropulses, both of which are suitable for their application to high average power FELs. They however suffer from the back-bombardment effect [1], i.e., in conventional RF guns, electrons are extracted from cathode also in the latter half of accelerating phase and tend to back-stream to hit the cathode, and as a result the macropulse duration is limited down to severalμsec Against this adverse effect in thermionic RF guns, introduction of the triode structure has been proposed [2], where the accelerating phase and amplitude nearby the cathode can be controlled regardless of the phase of the first accelerating cell in the conventional RF gun. Our one-dimensional particle simulation results predict that the back-bombardment power can be reduced by 99 % only with 30-40 kW RF power fed to the grid in the present triode structure with an optimal phase difference from th...

Photon emission produced by Kr+ ions bombardment of Cr and Cr2O3 targets

International Nuclear Information System (INIS)

Boujlaidi, A. El; Hammoum, K.; Jadoual, L.; Jourdani, R.; Ait El Fqih, M.; Aouchiche, H.; Kaddouri, A.

2015-01-01

The sputter induced photon spectroscopy technique was used to study the luminescence spectra of the species sputtered from chromium powder and its oxide Cr 2 O 3 , during 5 keV Kr + ions bombardment in vacuum better than 10 −7 torr. The optical spectra recorded between 350 and 470 nm exhibit discrete lines which are attributed to neutral excited atoms of chromium (Cr I lines). The experiments are also performed under 10 −5 torr ultra pure oxygen partial pressure. The results demonstrate that the measured intensities of the emitted photons are always higher in the presence of oxygen and even higher than those obtained for Cr 2 O 3 target. In the presence of oxygen vapor we assume that an oxide film is formed on the chromium surface which is responsible of the increase of photon emission. This variation in the intensities is correctly explained in the model of electron transfer processes between the excited sputtered atom and the bombarded surface. This model suggests that the structure formed on the Cr surface in the case of oxygenated chromium is closer to that of Cr 2 O 3 oxide

Comparison of the Cellient(™) automated cell block system and agar cell block method.

Science.gov (United States)

Kruger, A M; Stevens, M W; Kerley, K J; Carter, C D

2014-12-01

To compare the Cellient(TM) automated cell block system with the agar cell block method in terms of quantity and quality of diagnostic material and morphological, histochemical and immunocytochemical features. Cell blocks were prepared from 100 effusion samples using the agar method and Cellient system, and routinely sectioned and stained for haematoxylin and eosin and periodic acid-Schiff with diastase (PASD). A preliminary immunocytochemical study was performed on selected cases (27/100 cases). Sections were evaluated using a three-point grading system to compare a set of morphological parameters. Statistical analysis was performed using Fisher's exact test. Parameters assessing cellularity, presence of single cells and definition of nuclear membrane, nucleoli, chromatin and cytoplasm showed a statistically significant improvement on Cellient cell blocks compared with agar cell blocks (P cell groups, PASD staining or the intensity or clarity of immunocytochemical staining. A discrepant immunocytochemistry (ICC) result was seen in 21% (13/63) of immunostains. The Cellient technique is comparable with the agar method, with statistically significant results achieved for important morphological features. It demonstrates potential as an alternative cell block preparation method which is relevant for the rapid processing of fine needle aspiration samples, malignant effusions and low-cellularity specimens, where optimal cell morphology and architecture are essential. Further investigation is required to optimize immunocytochemical staining using the Cellient method. © 2014 John Wiley & Sons Ltd.

Donor-Acceptor Block Copolymers: Synthesis and Solar Cell Applications

Directory of Open Access Journals (Sweden)

Kazuhiro Nakabayashi

2014-04-01

Full Text Available Fullerene derivatives have been widely used for conventional acceptor materials in organic photovoltaics (OPVs because of their high electron mobility. However, there are also considerable drawbacks for use in OPVs, such as negligible light absorption in the visible-near-IR regions, less compatibility with donor polymeric materials and high cost for synthesis and purification. Therefore, the investigation of non-fullerene acceptor materials that can potentially replace fullerene derivatives in OPVs is increasingly necessary, which gives rise to the possibility of fabricating all-polymer (polymer/polymer solar cells that can deliver higher performance and that are potentially cheaper than fullerene-based OPVs. Recently, considerable attention has been paid to donor-acceptor (D-A block copolymers, because of their promising applications as fullerene alternative materials in all-polymer solar cells. However, the synthesis of D-A block copolymers is still a challenge, and therefore, the establishment of an efficient synthetic method is now essential. This review highlights the recent advances in D-A block copolymers synthesis and their applications in all-polymer solar cells.

Tune Up: Automotive Mechanics Instructional Program. Block 5.

Science.gov (United States)

O'Brien, Ralph D.

The fifth of six instructional blocks in automotive mechanics, the lessons and supportive information in the document provide a guide for teachers in planning an instructional program in automotive tune-ups at the secondary and post secondary level. The material, as organized, is a suggested sequence of instruction within each block. Each lesson…

Fuel System: Automotive Mechanics Instructional Program. Block 4.

Science.gov (United States)

O'Brien, Ralph D.

The fourth of six instructional blocks in automotive mechanics, the lessons and supportive information in the document provide a guide for teachers in planning an instructional program in automotive fuel systems at the secondary and post secondary level. The material, as organized, is a suggested sequence of instruction within each block. Each…

Cooling System: Automotive Mechanics Instructional Program. Block 6.

Science.gov (United States)

O'Brien, Ralph D.

The last of six instructional blocks in automotive mechanics, the lessons and supportive information in the document provide a guide for teachers in planning an instructional program in the automotive cooling system at the secondary and post secondary level. The material, as organized, is a suggested sequence of instruction within each block. Each…

Using GRIDVIEW to Better Understand the Early Bombardment History of the Moon, Mars and Earth

Science.gov (United States)

Frey, Herbert

2012-01-01

For more than a decade we have used GRIDVIEW to help analyze topographic and related data for Mars and more recently for the Moon. Our focus has been to employ the stretching, contouring, profiling, circle-fitting and other capabilities of GRIDVIEW to search for Quasi-Circular Depressions (CTAs) in MOLA, LOLA and other topographic data, and for Circular Thin Areas (CTAs) in Mars and Moon model crustal thickness data. Both QCDs and CTAs likely represent buried or obscured impact craters not readily visible in image data. We found clear evidence for a much larger population of buried impact craters in the northern lowlands of Mars (Frey et al. 2002), suggesting that part of the Red Planet is not significantly younger than the southern highlands. Edgar and Frey (2008) found that the N(300) crater retention ages of both areas were essentially identical, a conclusion confirmed by Wyatt (unpublished data) using more recent crustal thickness data for Mars. MOLA topographic data and MOLA-derived crustal thickness data were used to both identify a large number of previously unrecognized very large impact basins (D> 1000 km) on Mars and to determine relative crater retention ages for them (Frey, 2008). The distribution of N(300) CRAs suggested most formed in a relatively short interval of time. This dating also suggested the main magnetic field of Mars disappeared during this period (Lillis et al., 2008), because only the youngest basins systematically lack a remagnetized signature. Similar QCD and CTA analysis of first Clementine (Frey, 2011) and more recently LOLA topographic and LOLA-derived crustal thickness data for the Moon (Frey et al., 2011) revealed a significantly larger population of impact basins > 300 km in diameter than previously known. N(50) CRAs suggest a two-peak distribution of ages (Frey, 2012). An improved counting process confirms the two peaks, perhaps indicating both a pre-Nectaris Early Heavy Bombardment (EHB) as well as a Late Heavy Bombardment (LHB

Search for superheavy elements in the bombardment of 248Cm with 48Ca

International Nuclear Information System (INIS)

Hulet, E.K.; Lougheed, R.W.; Wild, J.F.; Landrum, J.H.; Stevenson, P.C.; Ghiorso, A.; Nitschke, J.M.; Otto, R.J.; Morrissey, D.J.; Baisden, P.A.; Gavin, B.F.; Lee, D.; Silva, R.J.; Fowler, M.M.; Seaborg, G.T.

1977-01-01

We have searched for superheavy elements 110 to 116 with half-lives between 10 4 and 10 8 s in fractions chemically separated after each of a series of bombardments of 248 Cm made with 267-MeV 48 Ca ions. After 6 months of α and spontaneous-fission counting, our results provide no persuasive evidence for the presence of super-heavy elements. The most plausible explanation for not finding the superheavy elements is that they have either short half-lives or very small formation cross sections

The influence of noble-gas ion bombardment on the electrical and optical properties of clean silicon surfaces

International Nuclear Information System (INIS)

Martens, J.W.D.

1980-01-01

A study of the effect of argon and helium ion bombardment on the electrical and optical properties of the clean silicon (211) surface is described. The objective of the study was to determine the effect of noble gas ions on the density of surface states at the clean silicon surface. (Auth.)

Producing the radioelectric effect in solid dielectrics by bombardment with accelerated electrons. Obrazovaniye radioelektretnogo effekta v tverdykh dielektrikakh v rezul'tate oblucheniya ikh uskorennymi elektronami

Energy Technology Data Exchange (ETDEWEB)

Zavadovskaya, E K; Annenkov, Yu M; Boev, S G; Sigaev, G I

1976-01-01

A theoretical and experimental study was made concerning the kinetics of formation of electric moments in solid dielectrics bombarded with fast electrons in the atmosphere. The energy of bombarding electrons in the experiment ranged from 0.6 to 2.0 MeV, at an incident flux density ranging 1.10/sup -9/ to 5.10/sup -7/ A/cm/sup 2/. The specimens were actually grounded during bonbardment, owing to the high electrical conductivity of the ionized ambient gas, and the electric moments were equal to zero. The formation of electric moments occurred after cessation of the bombardment, because the density of the accumulated space charge had become redistributed. An examination was made of the redistribution of space-charge density due to the electrical conductivity of the dielectric, due to intrinsic charge carriers, and due to the release of charges stored in traps. Analytical relations derived for the kinetics of the electric moments give a qualitative description of the experimental results. 5 references.

The influence of energetic bombardment on the structure formation of sputtered zinc oxide films. Development of an atomistic growth model and its application to tailor thin film properties

Energy Technology Data Exchange (ETDEWEB)

Koehl, Dominik

2011-02-17

The focus of this work is the investigation of the growth of zinc oxide (ZnO) thin films. It is demonstrated that with a modified, ion beam assisted sputtering (IBAS) process, zinc oxide films can be deposited which exhibit a markedly improved crystalline order. Furthermore, it is demonstrated that intense energetic oxygen ion bombardment can be utilized to change film texture from the typical (002)-self-texture to an a-axis texture where the (002)-planes are perpendicular to the substrate surface. An understanding of the underlying mechanisms is developed which also facilitates a more detailed understanding of the action of ion bombardment during zinc oxide film growth. It is shown that zinc oxide films are susceptible to the influence of ion bombardment particularly in the nucleation regime of growth and that this finding is generally true for all observed structural changes induced by ion bombardment with various species, energies and flux densities. It is demonstrated not only that the initial growth stage plays an important role in the formation of a preferred growth orientation but also that the action of texture forming mechanisms in subsequent growth stages is comparatively weak. (orig.)

The influence of energetic bombardment on the structure formation of sputtered zinc oxide films. Development of an atomistic growth model and its application to tailor thin film properties

International Nuclear Information System (INIS)

Koehl, Dominik

2011-01-01

The focus of this work is the investigation of the growth of zinc oxide (ZnO) thin films. It is demonstrated that with a modified, ion beam assisted sputtering (IBAS) process, zinc oxide films can be deposited which exhibit a markedly improved crystalline order. Furthermore, it is demonstrated that intense energetic oxygen ion bombardment can be utilized to change film texture from the typical (002)-self-texture to an a-axis texture where the (002)-planes are perpendicular to the substrate surface. An understanding of the underlying mechanisms is developed which also facilitates a more detailed understanding of the action of ion bombardment during zinc oxide film growth. It is shown that zinc oxide films are susceptible to the influence of ion bombardment particularly in the nucleation regime of growth and that this finding is generally true for all observed structural changes induced by ion bombardment with various species, energies and flux densities. It is demonstrated not only that the initial growth stage plays an important role in the formation of a preferred growth orientation but also that the action of texture forming mechanisms in subsequent growth stages is comparatively weak. (orig.)

Producing p-type conductivity in self-compensating semiconductor material

International Nuclear Information System (INIS)

Vechten, J.A. van; Woodall, J.M.

1981-01-01

This relates to compound type semiconductor materials that exhibit self-compensated n-type conductivity. The process described imparts p-type conductivity to a body of normally n-conductivity self-compensated compound semiconductor material by bombarding it with charged particles, either electrons, protons or ions. Other possible steps include introducing an acceptor impurity and applying a coating onto the crystal body. This technique will allow new semiconductor structures to be made. For example, there are some compound semiconductor materials that exhibit n-conductivity only that have energy gap widths that would permit electrical to light conversion at frequency and colours not readily achieved in semiconductor devices. (U.K.)

Multi-block analysis coupled to laser-induced breakdown spectroscopy for sorting geological materials from caves.

Science.gov (United States)

Ammari, Faten; Bassel, Léna; Ferrier, Catherine; Lacanette, Delphine; Chapoulie, Rémy; Bousquet, Bruno

2016-10-01

In this study, multi-block analysis was applied for the first time to LIBS spectra provided by a portable LIBS system (IVEA Solution, France) equipped with three compact Czerny-Turner spectrometers covering the spectral ranges 200-397nm, 398-571nm and 572-1000nm. 41 geological samples taken from a laboratory-cave situated in the "Vézère valley", an area rich with prehistoric sites and decorated caves listed as a UNESCO world heritage in the south west of France, were analyzed. They were composed of limestone and clay considered as underlying supports and of two types of alterations referred as moonmilk and coralloid. Common Components and Specific Weights Analysis (CCSWA) allowed sorting moonmilk and coralloid samples. The loadings revealed higher amounts of magnesium, silicon, aluminum and strontium in coralloids and the saliences emphasized that among the three spectrometers installed in the LIBS instrument used in this work; that covering the range 572-1000nm was less contributive. This new approach for processing LIBS data not only provides good results for sorting geological materials but also clearly reveals which spectral range contains most of the information. This specific advantage of multi-block analysis could lead for some applications to simplify the design and to reduce the size of LIBS instruments. Copyright © 2016 Elsevier B.V. All rights reserved.

Analytical study of stress and deformation of HTR fuel blocks

International Nuclear Information System (INIS)

Tanaka, M.

1982-01-01

A two-dimensional finite element computer code named HANS-GR has been developed to predict the mechanical behavior of the graphite fuel blocks with realistic material properties and core environment. When graphite material is exposed to high temperature and fast neutron flux of high density, strains arise due to thermal expansion, irradiation-induced shrinkage and creep. Thus stresses and distortions are induced in the fuel block in which there are spatial variation of these strains. The analytical method used in the program to predcit these induced stresses and distortions by finite element method is discussed. In order to illustrate the versatility of the computer code, numerical results of two example analyses of the multi-hole type fuel elements in the VHTR Reactor are given. Two example analyses presented are those concerning the stresses in fuel blocks with control rod holes and distortions of the fuel blocks at the periphery of the reactor core. It is considered these phenomena should be carefully examined when the multi-hole type fuel elements are applied to VHTR. It is assured that the predicted mechanical behavior of the graphite components is strongly dependent on the material properties used and obtaining the reliable material property is important to make the analytical prediction a reliable one

Large area smoothing of surfaces by ion bombardment: fundamentals and applications

International Nuclear Information System (INIS)

Frost, F; Fechner, R; Ziberi, B; Voellner, J; Flamm, D; Schindler, A

2009-01-01

Ion beam erosion can be used as a process for achieving surface smoothing at microscopic length scales and for the preparation of ultrasmooth surfaces, as an alternative to nanostructuring of various surfaces via self-organization. This requires that in the evolution of the surface topography different relaxation mechanisms dominate over the roughening, and smoothing of initially rough surfaces can occur. This contribution focuses on the basic mechanisms as well as potential applications of surface smoothing using low energy ion beams. In the first part, the fundamentals for the smoothing of III/V semiconductors, Si and quartz glass surfaces using low energy ion beams (ion energy: ≤2000 eV) are reviewed using examples. The topography evolution of these surfaces with respect to different process parameters (ion energy, ion incidence angle, erosion time, sample rotation) has been investigated. On the basis of the time evolution of different roughness parameters, the relevant surface relaxation mechanisms responsible for surface smoothing are discussed. In this context, physical constraints as regards the effectiveness of surface smoothing by direct ion bombardment will also be addressed and furthermore ion beam assisted smoothing techniques are introduced. In the second application-orientated part, recent technological developments related to ion beam assisted smoothing of optically relevant surfaces are summarized. It will be demonstrated that smoothing by direct ion bombardment in combination with the use of sacrificial smoothing layers and the utilization of appropriate broad beam ion sources enables the polishing of various technologically important surfaces down to 0.1 nm root mean square roughness level, showing great promise for large area surface processing. Specific examples are given for ion beam smoothing of different optical surfaces, especially for substrates used for advanced optical applications (e.g., in x-ray optics and components for extreme

Ion-materials interactions and their application

International Nuclear Information System (INIS)

Whitlow, H.J.

1998-01-01

The interaction of energetic ions and other charged particles with solid matter leads to a wealth of physical processes. This thesis comprises a collection of papers and an introductory commentary, which explore some aspects of how these interactions may be used for: (i) Characterisation of thin surface layers of material, (ii) characterisation of energetic charged particles, and (iii) modification of materials by ion bombardment. In (i) Elastic Recoil Detection using a detector system for measurement of Time of Flight and kinetic energy of recoiling target atoms has been developed as a quantitative method for elemental depth profiling of thin (0.5-1 μm) surface layers. This method has been applied to the study of reactions of metal/III-V structures, which are of importance for the semiconductor industry. (ii) MeV-ion - materials interactions have been used as the basis for developing Si p-i-n detectors for the CHICSi programme which will undertake experimental studies of heavy ion collisions at intermediate energies. This involved development and testing of extremely thin (10-12 μm) Si ΔE detectors for characterising light- and intermediate mass charged particles as well as calibration of Si p-i-n detectors and their susceptibility to radiation damage. (iii) Nuclear Reaction Analysis (NRA) with resonant nuclear reactions has been used to study modification of material with ion beams. In the first study, the accumulation of fluorine in BF 2 + ion implanted WSi 2 solid diffusion sources was investigated. The second study investigated if there was a correlation between photoluminescence and segregation of hydrogen to buried heterojunctions in plasma-etched III-V quantum-well structures. The ion bombardment in this case was during etching in an Ar+CH 4 plasma using an Electron Cyclotron Resonance (ECR) source. (author)

Intravenous coronary angiography utilizing K-emission and bremsstrahlung X-rays produced by electron bombardment

International Nuclear Information System (INIS)

1992-01-01

The screening of the general population for coronary artery disease would be practical if a method existed for visualizing the extent of occlusion after an intravenous injection of contrast agent. Measurements performed with synchrotron radiation at SSRL and NSLS have shown that such an intravenous angiography procedure would be possible with an intense source of monochromatic X-rays. Because of the high cost of an electron synchrotron, theoretical analysis and experiments using inanimate phantoms has been undertaken to demonstrate the feasibility of using the spectrum produced by two appropriately chosen anode materials when bombarded with electrons in the 100--500 keV energy range for angiography. By using the X-rays emitted at 120 degree to the incident electron direction, about 20--30% of the X-ray intensity would be due to K-emission lines. Calculations using the TIGERP Monte Carlo Code, have shown that high quality angiograms of human coronary arteries should be possible with a contrast agent containing ytterbium, if an electron beam pulses of 16 kJ were used for each anode target. The experimental program supported in part by the DOE has consisted of these theoretical calculations and experiments at the Dynamitron Electron Accelerator Facility at BNL

Modulation transfer function and detective quantum efficiency of electron bombarded charge coupled device detector for low energy electrons

Czech Academy of Sciences Publication Activity Database

Horáček, Miroslav

2005-01-01

Roč. 76, č. 9 (2005), 093704:1-6 ISSN 0034-6748 R&D Projects: GA ČR(CZ) GA202/03/1575 Keywords : electron bombarded CCD * modulation transfer function * detective quantum efficiency Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering Impact factor: 1.235, year: 2005

Ion induced electron emission statistics under Agm- cluster bombardment of Ag

Science.gov (United States)

Breuers, A.; Penning, R.; Wucher, A.

2018-05-01

The electron emission from a polycrystalline silver surface under bombardment with Agm- cluster ions (m = 1, 2, 3) is investigated in terms of ion induced kinetic excitation. The electron yield γ is determined directly by a current measurement method on the one hand and implicitly by the analysis of the electron emission statistics on the other hand. Successful measurements of the electron emission spectra ensure a deeper understanding of the ion induced kinetic electron emission process, with particular emphasis on the effect of the projectile cluster size to the yield as well as to emission statistics. The results allow a quantitative comparison to computer simulations performed for silver atoms and clusters impinging onto a silver surface.

Protein extraction from methanol fixed paraffin embedded tissue blocks: A new possibility using cell blocks

Science.gov (United States)

Kokkat, Theresa J.; McGarvey, Diane; Patel, Miral S.; Tieniber, Andrew D.; LiVolsi, Virginia A.; Baloch, Zubair W.

2013-01-01

Background: Methanol fixed and paraffin embedded (MFPE) cellblocks are an essential cytology preparation. However, MFPE cellblocks often contain limited material and their relatively small size has caused them to be overlooked in biomarker discovery. Advances in the field of molecular biotechnology have made it possible to extract proteins from formalin fixed and paraffin embedded (FFPE) tissue blocks. In contrast, there are no established methods for extracting proteins from MFPE cellblocks. We investigated commonly available CHAPS (3-[(3-cholamidopropyl) dimethylammonio]-1-propanesulfonate) buffer, as well as two commercially available Qiagen® kits and compared their effectiveness on MFPE tissue for protein yields. Materials and Methods: MFPE blocks were made by Cellient™ automated system using human tissue specimens from normal and malignant specimens collected in ThinPrep™ Vials. Protein was extracted from Cellient-methanol fixed and paraffin embedded blocks with CHAPS buffer method as well as FFPE and Mammalian Qiagen® kits. Results: Comparison of protein yields demonstrated the effectiveness of various protein extraction methods on MFPE cellblocks. Conclusion: In the current era of minimally invasive techniques to obtain minimal amount of tissue for diagnostic and prognostic purposes, the use of commercial and lab made buffer on low weight MFPE scrapings obtained by Cellient® processor opens new possibilities for protein biomarker research. PMID:24403950

A procedure for the hardening of materials

International Nuclear Information System (INIS)

Dearnaley, G.

1984-01-01

A method of hardening metals or ceramics which have fcc, bcc or hcp structures in which two species of differing atomic radii are introduced into the material to be hardened. One species is of a size such that it can diffuse through the lattice normally. The other is of a size such that it can diffuse readily only along dislocations. Ion bombardment is the preferred method of introducing the species with different atomic radii. The material to be hardened is subjected to heat and plastic deformation so as to cause a large number of dislocations with jogs. The species meet at the jogs where they interact and are trapped and set up strain fields which prevent further deformation of the material. (author)

Block Copolymers: Synthesis and Applications in Nanotechnology

Science.gov (United States)

Lou, Qin

This study is focused on the synthesis and study of (block) copolymers using reversible deactivation radical polymerizations (RDRPs), including atom transfer radical polymerization (ATRP) and reversible addition-fragmentation chain transfer (RAFT) polymerization. In particular, two primary areas of study are undertaken: (1) a proof-of-concept application of lithographic block copolymers, and (2) the mechanistic study of the deposition of titania into block copolymer templates for the production of well-ordered titania nanostructures. Block copolymers have the ability to undergo microphase separation, with an average size of each microphase ranging from tens to hundreds of nanometers. As such, block copolymers have been widely considered for nanotechnological applications over the past two decades. The development of materials for various nanotechnologies has become an increasingly studied area as improvements in many applications, such as those found in the semiconductor and photovoltaic industries are constantly being sought. Significant growth in developments of new synthetic methods ( i.e. RDRPs) has allowed the production of block copolymers with molecular (and sometimes atomic) definition. In turn, this has greatly expanded the use of block copolymers in nanotechnology. Herein, we describe the synthesis of statistical and block copolymers of 193 nm photolithography methacrylate and acrylate resist monomers with norbornyl and adamantyl moieties using RAFT polymerization.. For these resist (block) copolymers, the phase separation behaviors were examined by atomic force microscopy (AFM). End groups were removed from the polymers to avoid complications during the photolithography since RAFT end groups absorb visible light. Poly(glycidyl methacrylate-block-polystyrene) (PGMA-b-PS) was synthesize by ATRP and demonstrated that this block copolymer acts as both a lithographic UV (365 nm) photoresist and a self-assembly material. The PGMA segments can undergo cationic

Recovery of 201Tl by ion exchange chromatography from proton bombarded thallium cyclotron targets

International Nuclear Information System (INIS)

Walt, T.N. van der; Naidoo, C.

2000-01-01

A method based on ion exchange chromatography is presented for the recovery of 201 Tl and its precursor 201 Pb from proton bombarded natural thallium cyclotron targets. After bombardment the target is dissolved in diluted nitric acid. Water, hydrazine and ammonium acetate are added to the solution and the lead radioisotopes separated from the thallium by cation exchange chromatography on a Bio-Rex 70 column. The sorbed lead radioisotopes are eluted with dilute nitric acid and the separation repeated on a second Bio-Rex 70 column. After elution of the remaining thallium the column is left for 32 hours and the 201 Tl formed by decay of 201 Pb is eluted with an ammonium acetate solution. The 201 Tl eluate is acidified with a HNO 3 -HBr-Br 2 mixture and the resulting solution is passed through an AG MP-1 anion exchanger column to remove any remaining lead isotopes. The 201 Tl is eluted with a hydrazine solution, the eluate evaporated to dryness and the 201 Tl finally dissolved in an appropriate solution to produce a 201 TlCl solution suitable for medical use. A high quality 201 Tl product is obtained containing ≤ 0.1 μg of Tl/mCi (37 MBq) 201 Tl. The radionuclidic impurities are less than the maximum values specified by the US Pharmacopoeia and the British Pharmacopoeia. (orig.)

Radiation damages of material surfaces by plasma emission in thermonuclear devices. Methods of study of surface phenomena and simulation effect of thermonuclear plasma

International Nuclear Information System (INIS)

Rybalko, V.F.

1978-01-01

Phenomena that can introduce a controlling contribution into the erosion of the first wall surface in thermonuclear reactor are reviewed. Considered are the main characteristics of the physical disintegration: dependence of the disintegration coefficient upon the energy and the incidence angle of the bombarding particles, upon the atomic number of the material of the target and the type of bombarding particles. Stressed is the lack of reliable data on the disintegration of materials by light ions, which are of a maximum interest in relation to the controlled thermonuclear synthesis. The chemical disintegration and some regularities of it for the carbon-hydrogen and carbon-oxygen systems are discussed briefly. Listed are the main properties of blistering and its contribution to the erosion of crystalline surfaces

Molecular Building Blocks for Nanotechnology From Diamondoids to Nanoscale Materials and Applications

CERN Document Server

Mansoori, G. Ali; Assoufid, Lahsen; Zhang, Guoping

2007-01-01

This book is a result of the research and educational activities of a group of outstanding scientists worldwide who have authored the chapters of this book dealing with the behavior of nanoscale building blocks. It contains a variety of subjects covering computational, dry and wet nanotechnology. The state-of-the-art subject matters presented here provide the reader with the latest developments on ongoing nanoscience and nanotechnology research from the bottom-up approach, which starts with with atoms and molecules as molecular building blocks.

Energy dependence of the absorptive potential for sub-Coulomb energy proton bombardment of zirconium and molybdenum isotopes

International Nuclear Information System (INIS)

Flynn, D.S.; Hershberger, R.L.; Gabbard, F.

1985-01-01

The measured (p,p) and (p,n) excitation functions for /sup 92,94,96/Zr and /sup 95,98,100/Mo were fitted in the energy range 2 3 for all isotopes studied as the proton bombarding energy is increased toward 15 MeV. This result is consistent with results from analyses at higher energies

Production of no-carrier-added 139Pr via precursor decay in the proton bombardment of natPr

International Nuclear Information System (INIS)

Steyn, G.F.; Vermeulen, C.; Nortier, F.M.; Szelecsenyi, F.; Kovacs, Z.; Qaim, S.M.

2006-01-01

Excitation functions and production rates are presented for various Pr and Nd radionuclides formed in the bombardment of Pr with protons, from their respective thresholds up to 100 MeV. The indirect production route 141 Pr(p, 3n) 139m Nd → 139 Pr is investigated as an alternative to the direct production route 140 Ce(p, 2n) 139 Pr for producing no-carrier-added 139 Pr of high radionuclidic purity. The simultaneous production of 139 Pr and 140 Nd using Pr as target is investigated. The advantages and disadvantages of both production routes are discussed. Experimental thick-target production rates are presented for selected Pr radionuclides formed in the bombardment of nat Ce with protons at incident energies of 20, 26 and 32 MeV. All the experimental excitation functions obtained in this work are compared with theoretical predictions by means of the geometry-dependent hybrid (GDH) model as implemented in the code ALICE-IPPE. The results of this work are also compared with previous literature experimental data, if available

Analysis of natural stone block pavements in urban shared areas

Directory of Open Access Journals (Sweden)

Pablo Zoccali

2018-06-01

Full Text Available This paper analysed and verified an existing block stone pavement in an urban shared area. Fatigue and rutting verification was performed respectively for bound and unbound pavement materials using analytical curves available in the literature. The commercial finite element (FE software Abaqus® was used to calculate the response of the pavement when subjected to different loading, construction and geometrical configurations (i.e. type of analysis, shape and size of meshes, boundary conditions, and bonding contacts between the pavements layers. At the end of this study, a static model of a structure with hexahedral blocks having sides of 0.02 m, with full bonded layers and restrained horizontal displacements on the model sides, was implemented to evaluate the maximum tensile stress induced in a block when the load is applied at its centre. This analysis highlighted the need for rigorous criteria for a correct design, in order to avoid inappropriate and expensive use of road materials. Keywords: Block pavement, Commercial vehicle loads, Finite element model, Hexagonal Stone block, Pedestrian pavement, Shared area

Synthesis and properties of lyotropic poly(amide-block-aramid) copolymers

NARCIS (Netherlands)

De Ruijter, C.

2006-01-01

This thesis describes the synthesis and properties of liquid crystalline block copolymers comprised of alternating rigid and flexible blocks for the preparation of self-reinforcing materials. The incentive for this work was the expectation that the rigid segments would phase separate on a

Block Copolymer Adhesion Measured by Contact Mechanics Methods

Science.gov (United States)

Falsafi, A.; Bates, S.; Tirrell, M.; Pocius, A. V.

1997-03-01

Adhesion measurements for a series of polyolefin diblocks and triblocks are presented. These materials have poly(ethylene-propylene) or poly(ethyl-ethylene) rubbery block, and semicrystalline polyethylene block as physical crosslinker. The experiments consist of compression and decompression profiles of contact area between the samples as a function of normal load, analyzed by the JKR Theory. The samples are prepared either by formation of caps from the bulk material in melting and subsequent cooling, and/or coating them in thin films on surface modified elastic foundations of polydimethylsiloxane caps. The latter minimizes the viscoelastic losses which are dominant in the bulk of material. The effect of molecular architecture and microstructure on adhesion energy and dynamics of separation, obtained from decompression experiments, is discussed in view of their influence on molecular arrangements at the contacting surfaces.

Production of the Ne Auger electrons by Ne/sup +/ bombardment of Mg and Al surfaces

Energy Technology Data Exchange (ETDEWEB)

Ferrante, J; Pepper, S V [National Aeronautics and Space Administration, Cleveland, Ohio (USA). Lewis Research Center

1976-07-01

The authors have bombarded Mg and Al surfaces with Ne/sup +/ ions and in this letter present evidence for the production of an inner shell vacancy in the Ne by the asymmetric Ne-Mg and Ne-Al collision. In addition, autoionization states of neutral Ne have been observed. These states are to be distinguished from the more usual case in Auger electron spectroscopy of de-excitation of an ion with a core vacancy.

Evaluation of Suitability of Non-Standardized Test Block for Ultrasonic Testing

International Nuclear Information System (INIS)

Kwon, Ho Young; Lim, Jong Ho; Kang, Sei Sun

2000-01-01

Standard Test Block(STB) for UT(Ultrasonic Testing) is a block approved by authoritative for material, shape and quality. STB is used for characteristic tests, sensitivity calibration and control of the time base range of UT inspection devices. The material, size and chemical components of STB should be strictly controlled to meet the related standards such as ASTM and JIS because it has an effect upon sensitivity, resolution and reproductivity of UT. The STBs which are not approved are sometimes used because the qualified STBs are very expensive. So, the purpose of this study is to survey the characteristics, quality and usability of Non-Standardized Test Blocks. Non-Standardized Test Blocks did not meet the standard requirements in size or chemical components, and ultrasonic characteristics. Therefore if the Non-Standardized Test Blocks are used without being tested, it's likely to cause errors in detecting the location and measuring the size of the defects

Optical radiation emitted by a silver surface bombarded by low-energy electrons

International Nuclear Information System (INIS)

Miserey, F.; Lebon, P.; Septier, A.; Trehin, F.; Beaugrand, C.

1975-01-01

Thick silver targets are obtained on flat glass discs by evaporation in a UHV cell (p -10 torr) and their optical coefficients measured by ellipsometry. A field-emission electron gun bombards a limited region of the target, corresponding to the entry pupil of a light spectrometer. Radiation emitted in the domain 250-600nm is analyzed for both normal and parallel polarizations. Spectral distributions of photons are obtained by using a very sensitive counting device including a multi channel analyzer. First experimental results concerning optical radiation generated by 6keV electrons are reported and compared to Transition Radiation and Bremsstrahlung theoretical spectra [fr

Applications of simulation experiments in LMFBR core materials technology

International Nuclear Information System (INIS)

Appleby, W.K.

1976-01-01

The development of charged particle bombardment experiments to simulate neutron irradiation induced swelling in austenitic alloys is briefly described. The applications of these techniques in LMFBR core materials technology are discussed. It is shown that use of the techniques to study the behavior of cold-worked Type-316 was instrumental in demonstrating at an early date the need for advanced materials. The simulation techniques then were used to identify alloying elements which can markedly decrease swelling and thus a focused reactor irradiation program is now in place to allow the future use of a lower swelling alloy for LMFBR core components

Secondary ion emission from metal surfaces bombarded by 0.5-10 keV protons and hydrogens

International Nuclear Information System (INIS)

Kitamura, Akira; Yano, Syukuro

1978-01-01

Secondary ion emission coefficients by bombardment of 0.5 - 10 keV protons K 11 and atomic hydrogens K 01 on copper, stainless steel, molybdenum and evaporated gold surfaces have been measured in a moderate vacuum. Results are summarized as follows; 1) There is no significant difference between K 11 and K 01 . 2) Differences in K 11 and K 11 between different samples of the same material and between the sample before baking-out and the same sample after baking-out are of the order of several tens of percent. 3) The incident particle energy E sub(max) at which K 11 and K 01 have the maximum value lies in the keV region, and increases with the target mass. According to the fact that E sub(max) differs substantially from the energy at which the elastic stopping power has the maximum value, a characteristic length l is introduced and calculated to be of the order of hundreds of A; the factor exp (-x/l) represents the degree of contribution of collision at depth x to K 11 or K 01 . (author)

32S-induced reactions at 10 MeV/u bombarding energy

International Nuclear Information System (INIS)

Betz, J.; Graef, H.; Novotny, R.; Pelte, D.; Winkler, U.

1983-01-01

The deep-inelastic processes of the reactions 32 S+ 28 Si, sup(nat)S, 40 Ca, 58 Ni, 74 Ge are studied at 10 MeV/u bombarding energy employing a kinematical coincidence spectrometer. From the measured energies, momenta, masses and atomic numbers of two heavy fragments the corresponding parameters for the unobserved reaction products and the reaction Q-values are deduced. It is found that the reactions generally show the pattern of a normal deep-inelastic process which is followed by the evaporation of several light particles. But with much less intensities other processes also seem to occur: three-fragment excit channels and incomplete energy damping which is correlated with the emission of a few light particles of high momenta. (orig.)

Measurement of electron emission due to energetic ion bombardment in plasma source ion implantation

Science.gov (United States)

Shamim, M. M.; Scheuer, J. T.; Fetherston, R. P.; Conrad, J. R.

1991-11-01

An experimental procedure has been developed to measure electron emission due to energetic ion bombardment during plasma source ion implantation. Spherical targets of copper, stainless steel, graphite, titanium alloy, and aluminum alloy were biased negatively to 20, 30, and 40 kV in argon and nitrogen plasmas. A Langmuir probe was used to detect the propagating sheath edge and a Rogowski transformer was used to measure the current to the target. The measurements of electron emission coefficients compare well with those measured under similar conditions.

Emplacement of small and large buffer blocks

International Nuclear Information System (INIS)

Saari, H.; Nikula, M.; Suikki, M.

2010-05-01

The report describes emplacement of a buffer structure encircling a spent fuel canister to be deposited in a vertical hole. The report deals with installability of various size blocks and with an emplacement gear, as well as evaluates the achieved quality of emplacement and the time needed for installing the buffer. Two block assembly of unequal size were chosen for examination. A first option involved small blocks, the use of which resulted in a buffer structure consisting of small sector blocks 200 mm in height. A second option involved large blocks, resulting in a buffer structure which consists of eight blocks. In these tests, the material chosen for both block options was concrete instead of bentonite. The emplacement test was a three-phase process. A first phase included stacking a two meter high buffer structure with small blocks for ensuring the operation of test equipment and blocks. A second phase included installing buffer structures with both block options to a height matching that of a canister-encircling cylindrical component. A third phase included testing also the installability of blocks to be placed above the canister by using small blocks. In emplacement tests, special attention was paid to the installability of blocks as well as to the time required for emplacement. Lifters for both blocks worked well. Due to the mass to be lifted, the lifter for large blocks had a more heavy-duty frame structure (and other lifting gear). The employed lifters were suspended in the tests on a single steel wire rope. Stacking was managed with both block sizes at adequate precision and stacked-up towers were steady. The stacking of large blocks was considerably faster. Therefore it is probably that the overall handling of the large blocks will be more convenient at a final disposal site. From the standpoint of reliability in lifting, the small blocks were safer to install above the canister. In large blocks, there are strict shape-related requirements which are

Building Blocks for Personal Brands

Science.gov (United States)

Thomas, Lisa Carlucci

2011-01-01

In this article, the author discusses the four essential building blocks for personal brands: (1) name; (2) message; (3) channels; and (4) bridges. However, outstanding building materials can only take a person so far. The author emphasizes that vision, determination, faith, a sense of humor, and humility are also required.

Bremsstrahlung Based Positron Annihilation Spectroscopy for Material Defect Analysis

International Nuclear Information System (INIS)

Selim, F.A.; Wells, D.P.; Harmon, F.; Kwofie, J.; Lancaster, G.; Jones, J.L.

2003-01-01

The Idaho Accelerator Center (IAC) has developed new techniques for Positron Annihilation Spectroscopy (PAS) using highly penetrating γ-rays to create positrons inside the material via pair production. γ-Ray induced positron annihilation spectroscopy can provide highly penetrating probes for material characterization and defect analysis. Bremsstrahlung beams from small, pulsed electron Linacs (6 MeV) have been used to bombard the materials to generate positrons, which annihilate with the material electrons emitting 511 keV radiation. We have also synchronized bremsstrahlung pulses with laser irradiation pulses to study dynamic structural changes in material. In addition, we have developed another method using (p,γ) reactions from a 2 MeV proton beam, which induce coincident γ-rays to perform positron life-time spectroscopy. We have showed the feasibility of extending PAS into thick samples and a wide variety of materials and industrial applications

The search for molecular effects in range corrections: boron determination by proton bombardment

International Nuclear Information System (INIS)

Olivier, C.; Peisach, M.

1985-01-01

Three different nuclear reactions viz. 10 B(p,αγ) 7 Be, 10 B(p,p,'γ) 10 B, and 11 B(p,p'γ) 11 B were used to analyse 21 pure boron compounds and mixtures of known composition by prompt gamma-ray spectrometry under proton bombardment. Elemental stopping powers were calculated from tables and used to compute the stopping power of the target matrices by Bragg's Law. Apparent discrepancies in the measured yield could point to deviations from Bragg's Law and hence to molecular effects. The maximum value for any molecular effect was found to be < 8,3%

Analysis of Block OMP using Block RIP

OpenAIRE

Wang, Jun; Li, Gang; Zhang, Hao; Wang, Xiqin

2011-01-01

Orthogonal matching pursuit (OMP) is a canonical greedy algorithm for sparse signal reconstruction. When the signal of interest is block sparse, i.e., it has nonzero coefficients occurring in clusters, the block version of OMP algorithm (i.e., Block OMP) outperforms the conventional OMP. In this paper, we demonstrate that a new notion of block restricted isometry property (Block RIP), which is less stringent than standard restricted isometry property (RIP), can be used for a very straightforw...

Merging Bottom-Up with Top-Down: Continuous Lamellar Networks and Block Copolymer Lithography

Science.gov (United States)

Campbell, Ian Patrick

Block copolymer lithography is an emerging nanopatterning technology with capabilities that may complement and eventually replace those provided by existing optical lithography techniques. This bottom-up process relies on the parallel self-assembly of macromolecules composed of covalently linked, chemically distinct blocks to generate periodic nanostructures. Among the myriad potential morphologies, lamellar structures formed by diblock copolymers with symmetric volume fractions have attracted the most interest as a patterning tool. When confined to thin films and directed to assemble with interfaces perpendicular to the substrate, two-dimensional domains are formed between the free surface and the substrate, and selective removal of a single block creates a nanostructured polymeric template. The substrate exposed between the polymeric features can subsequently be modified through standard top-down microfabrication processes to generate novel nanostructured materials. Despite tremendous progress in our understanding of block copolymer self-assembly, continuous two-dimensional materials have not yet been fabricated via this robust technique, which may enable nanostructured material combinations that cannot be fabricated through bottom-up methods. This thesis aims to study the effects of block copolymer composition and processing on the lamellar network morphology of polystyrene-block-poly(methyl methacrylate) (PS-b-PMMA) and utilize this knowledge to fabricate continuous two-dimensional materials through top-down methods. First, block copolymer composition was varied through homopolymer blending to explore the physical phenomena surrounding lamellar network continuity. After establishing a framework for tuning the continuity, the effects of various processing parameters were explored to engineer the network connectivity via defect annihilation processes. Precisely controlling the connectivity and continuity of lamellar networks through defect engineering and

Preparation of Autoclaved Foamed Concrete Block from Fly Ash and Carbide Slag

Directory of Open Access Journals (Sweden)

Tan Xing

2018-01-01

Full Text Available To achieve the comprehensive utilization of solid waste and reduce costs, fly ash, carbide slag, and low-clinker cement were used to produce lightweight foamed concrete block. Granulated blast-furnace slag (GBFS was used as composition correction material in the block. The effects of curing temperature and dosage of low-clinker cement on the performance of foamed concrete block were investigated. The optimal material proportioning is obtained: fly ash 58.5%, carbide slag 20%, GBFS 10%, gypsum 1.5% and low-clinker cement 10%. The proper curing regime is “temperature rising 4h-180°C constant temperature 4h-natural cooling”. The results indicate that the compressive strength of the block reaches 3.55 MPa while the density is 616.9 kg/m3. The performance of the product meets JC/T 1062-2007 (China professional standard of foamed concrete block.

Diamond-like carbon layers modified by ion bombardment during growth and researched by Resonant Ultrasound Spectroscopy

Czech Academy of Sciences Publication Activity Database

Kocourek, Tomáš; Jelínek, Miroslav; Písařík, Petr; Remsa, Jan; Janovská, Michaela; Landa, Michal; Zemek, Josef; Havránek, Vladimír

2017-01-01

Roč. 417, Sep (2017), s. 213-217 ISSN 0169-4332 R&D Projects: GA ČR(CZ) GA15-05864S Institutional support: RVO:68378271 ; RVO:61388998 ; RVO:61389005 Keywords : in-situ ion bombardment * pulsed laser deposition * diamond-like carbon * hybrid technology * flm modification Subject RIV: BL - Plasma and Gas Discharge Physics OBOR OECD: Fluids and plasma physics (including surface physics) Impact factor: 3.387, year: 2016

31 CFR 595.301 - Blocked account; blocked property.

Science.gov (United States)

2010-07-01

... (Continued) OFFICE OF FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY TERRORISM SANCTIONS REGULATIONS General Definitions § 595.301 Blocked account; blocked property. The terms blocked account and blocked...

FY 1999 project on the development of new industry support type international standards. Standardization of a method to evaluate the performance of block paving use fiber materials; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Block hosoyo sen'i zairyo no seino hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As to fiber materials (geotextile) used for block paving, survey/experimental study were carried out with the aim of establishing an evaluation method of the performance which has accordance with the site and of proposing it to international standards. The FY 1999 results were outlined. From the results of the literature survey abroad and in Japan, it was found out that the evaluation method of geotextile as simple substrate had already been standardized, but the evaluation method for durability/separation performance/drainage performance as the block paving system was not standardized. The use of geotextile in block paving is mostly for prevention of outflow of cushion sand, and geotextile is paved in the boundary between sand cushion bed and roadbed. From the survey of durability/properties in IL block paving where geotextile was laid, the useful basic data were obtained. About geotextile, there are correlations between the elongation rate and the tensile strength. It was confirmed that the geotextile laid on granular materials is higher in elongation rate, and it is less in damage than that on the permeable bitumen processed roadbed. (NEDO)

Ion-bombardment-induced reduction in vacancies and its enhanced effect on conductivity and reflectivity in hafnium nitride films

Energy Technology Data Exchange (ETDEWEB)

Gu, Zhiqing; Wang, Jiafu; Hu, Chaoquan; Zhang, Xiaobo; Dang, Jianchen; Gao, Jing; Zheng, Weitao [Jilin University, School of Materials Science and Engineering, Key Laboratory of Mobile Materials, MOE, and State Key Laboratory of Superhard Materials, Changchun (China); Zhang, Sam [Nanyang Technological University, School of Mechanical and Aerospace Engineering, Singapore (Singapore); Wang, Xiaoyi [Chinese Academy of Sciences, Key Laboratory of Optical System Advanced Manufacturing Technology, Changchun Institute of Optics, Fine Mechanics and Physics, Changchun (China); Chen, Hong [Jilin University, Department of Control Science and Engineering, Changchun (China)

2016-08-15

Although the role of ion bombardment on electrical conductivity and optical reflectivity of transition metal nitrides films was reported previously, the results were controversial and the mechanism was not yet well explored. Here, we show that proper ion bombardment, induced by applying the negative bias voltage (V{sub b}), significantly improves the electrical conductivity and optical reflectivity in rocksalt hafnium nitride films regardless of level of stoichiometry (i.e., in both near-stoichiometric HfN{sub 1.04} and over-stoichiometric HfN{sub 1.17} films). The observed improvement arises from the increase in the concentration of free electrons and the relaxation time as a result of reduction in nitrogen and hafnium vacancies in the films. Furthermore, HfN{sub 1.17} films have always much lower electrical conductivity and infrared reflectance than HfN{sub 1.04} films for a given V{sub b}, owing to more hafnium vacancies because of larger composition deviation from HfN exact stoichiometry (N:Hf = 1:1). These new insights are supported by good agreement between experimental results and theoretical calculations. (orig.)

Isostatic compression of buffer blocks. Middle scale

International Nuclear Information System (INIS)

Ritola, J.; Pyy, E.

2012-01-01

Manufacturing of buffer components using isostatic compression method has been studied in small scale in 2008 (Laaksonen 2010). These tests included manufacturing of buffer blocks using different bentonite materials and different compression pressures. Isostatic mould technology was also tested, along with different methods to fill the mould, such as vibration and partial vacuum, as well as a stepwise compression of the blocks. The development of manufacturing techniques has continued with small-scale (30 %) blocks (diameter 600 mm) in 2009. This was done in a separate project: Isostatic compression, manufacturing and testing of small scale (D = 600 mm) buffer blocks. The research on the isostatic compression method continued in 2010 in a project aimed to test and examine the isostatic manufacturing process of buffer blocks at 70 % scale (block diameter 1200 to 1300 mm), and the aim was to continue in 2011 with full-scale blocks (diameter 1700 mm). A total of nine bentonite blocks were manufactured at 70 % scale, of which four were ring-shaped and the rest were cylindrical. It is currently not possible to manufacture full-scale blocks, because there is no sufficiently large isostatic press available. However, such a compression unit is expected to be possible to use in the near future. The test results of bentonite blocks, produced with an isostatic pressing method at different presses and at different sizes, suggest that the technical characteristics, for example bulk density and strength values, are somewhat independent of the size of the block, and that the blocks have fairly homogenous characteristics. Water content and compression pressure are the two most important properties determining the characteristics of the compressed blocks. By adjusting these two properties it is fairly easy to produce blocks at a desired density. The commonly used compression pressure in the manufacturing of bentonite blocks is 100 MPa, which compresses bentonite to approximately

Isostatic compression of buffer blocks. Middle scale

Energy Technology Data Exchange (ETDEWEB)

Ritola, J.; Pyy, E. [VTT Technical Research Centre of Finland, Espoo (Finland)

2012-01-15

Manufacturing of buffer components using isostatic compression method has been studied in small scale in 2008 (Laaksonen 2010). These tests included manufacturing of buffer blocks using different bentonite materials and different compression pressures. Isostatic mould technology was also tested, along with different methods to fill the mould, such as vibration and partial vacuum, as well as a stepwise compression of the blocks. The development of manufacturing techniques has continued with small-scale (30 %) blocks (diameter 600 mm) in 2009. This was done in a separate project: Isostatic compression, manufacturing and testing of small scale (D = 600 mm) buffer blocks. The research on the isostatic compression method continued in 2010 in a project aimed to test and examine the isostatic manufacturing process of buffer blocks at 70 % scale (block diameter 1200 to 1300 mm), and the aim was to continue in 2011 with full-scale blocks (diameter 1700 mm). A total of nine bentonite blocks were manufactured at 70 % scale, of which four were ring-shaped and the rest were cylindrical. It is currently not possible to manufacture full-scale blocks, because there is no sufficiently large isostatic press available. However, such a compression unit is expected to be possible to use in the near future. The test results of bentonite blocks, produced with an isostatic pressing method at different presses and at different sizes, suggest that the technical characteristics, for example bulk density and strength values, are somewhat independent of the size of the block, and that the blocks have fairly homogenous characteristics. Water content and compression pressure are the two most important properties determining the characteristics of the compressed blocks. By adjusting these two properties it is fairly easy to produce blocks at a desired density. The commonly used compression pressure in the manufacturing of bentonite blocks is 100 MPa, which compresses bentonite to approximately

Concrete Waste as a Cement Replacement Material in Concrete Blocks for Optimization of Thermal and Mechanical Properties

Directory of Open Access Journals (Sweden)

Rosman M.S.

2014-01-01

Full Text Available The sustainability of the natural environment and eco-systems is of great importance. Waste generated from construction forces mankind to find new dumping grounds and at the same time, more natural resources are required for use as construction materials. In order to overcome this problem, this study was conducted to investigate the use of concrete waste in concrete blocks with a special focus on the thermal and mechanical properties of the resulting products. Three varieties of concrete mixtures were prepared, whereby they each contained different amounts of concrete waste of 0%, 5% and 15%, respectively. These mixtures were formed into cube specimens and were then analysed for data on their compressive strength, density and ultrasonic pulse. Thermal investigations were carried out on each admixture as well as on a control concrete block of model design. The thermal data results indicated that the 15% concrete waste mixture had the lowest temperature in comparison to the surrounding air. For density and compressive strength, the highest readings came from the control mixture at 2390 kg/m3 and 40.69 N/mm2, respectively, at 28 days. In terms of pulse velocity, the 5% concrete waste mixture indicated medium quality results of 4016 m/s.

Fast Atom Bombardment Spectrometry - a novel analytical method for biologically interesting, non-volatile substances

International Nuclear Information System (INIS)

Schmid, E.

1987-03-01

Today important chemical substances like proteins can be produced easily and in large amounts. The primary structure of proteins can be analysed automatically, however the procedure can take some months of time. A novel method, fast atom bombardment mass spectrometry (FAB-MS) in combination with enzymatic degradation not only decreases the analysis time, but gives also additional information about the primary structure. Especially for the verification of protein structures - which is important for recombinant proteins - FAB-MS is a very useful method. 40 refs., 56 figs. (P.W.)

Nerve Blocks

Science.gov (United States)

... News Physician Resources Professions Site Index A-Z Nerve Blocks A nerve block is an injection to ... the limitations of Nerve Block? What is a Nerve Block? A nerve block is an anesthetic and/ ...

Enhancement of sp3 hybridized C in amorphous carbon films by Ar ion bombardment and Si incorporation

International Nuclear Information System (INIS)

Jung, Hae-Suk; Park, Hyung-Ho; Mendieta, I.R.; Smith, D.A.

2003-01-01

We report an effective method of increasing the sp 3 hybridization fraction in sputtered amorphous carbon (a-C) film by the combination of Ar ion bombardment and Si incorporation. In the deposition of an a-C film, Ar ion bombardment by controlling the applied bias voltage plays a role in creating high stress in film and causes the local bonding configuration to change to a sp 3 hybridized bond. Simultaneously, the incorporated Si in an a-C network breaks the sp 2 hybridized bonded ring and promotes the formation of a sp 3 hybridized bond. This enhancement of the sp 3 hybridized bonding characteristic is maximized for an a-C film with 23 at. % of Si and 100-150 V of applied bias voltage. In this region, the increase of resistivity, optical band gap, and mechanical hardness of a-C is attributed to the reduction of the sp 2 hybridized bonded ring and increased fraction of the sp 3 hybridized bond. However, at a higher bias voltage above 150 V, the enhancement effect is reduced due to the resputtering and thermally activated reconversion of a sp 3 to a sp 2 hybridized bond

Methane formation during deuteron bombardment of carbon in the energy range of 100 to 1500 eV

International Nuclear Information System (INIS)

Sone, K.

1982-01-01

Methane (CD 4 ) formation rates during deuteron bombardment of carbon (Papyex) have been measured in the energy range of 100 to 1500 eV. The temperature dependence of the methane formation rate is well explained by the model proposed by Erents et al. in the temperature range of 600 to 1150 K. The model, however, does not explain the dependence of the methane formation rate on the flux of incident deuterons at a certain temperature near Tsub(m) at which the formation rate has a maximum value. An alternative model is proposed in which the methane formation rate is assumed to be proportional to the product of the following three parameters: the surface concentration of deuterium atoms, the chemical reaction rate for the formation of methane, and the rate of production of vacancies on the surface by the deuteron bombardment. This model predicts an energy dependence of methane formation which has a maximum around 900 eV even at different deuteron fluxes, when the calculated result by Weissman and Sigmund is used for the surface deposited energy responsible for the production of vacancies. (author)

Fast atom bombardment tandem mass spectrometry of carotenoids

Energy Technology Data Exchange (ETDEWEB)

van Breeman, R.B. [Univ. of Illinois, Chicago, IL (United States); Schmitz, H.H.; Schwartz, S.J. [North Carolina State Univ., Raleigh, NC (United States)

1995-02-01

Positive ion fast atom bombardment (FAB) tandem mass spectrometry (MS-MS) using a double-focusing mass spectrometer with linked scanning at constant B/E and high-energy collisionally activated dissociation (CAD) was used to differentiate 17 different cartenoids, including {beta}-apo-8{prime}- carotenal, astaxanthin, {alpha}-carotene, {beta}-carotene, {gamma}-carotene, {zeta}-carotene, canthaxanthin, {beta}-cryptoxanthin, isozeaxanthin bis (pelargonate), neoxanthin, neurosporene, nonaprene, lutein, lycopene, phytoene, phytofluene, and zeaxanthin. The carotenoids were either synthetic or isolated from plant tissues. The use of FAB ionization minimized degradation or rearrangement of the carotenoid structures due to the inherent thermal instability generally ascribed to these compounds. Instead of protonated molecules, both polar xanthophylls and nonpolar carotenes formed molecular ions, M{sup {center_dot}+}, during FAB ionization. Following collisionally activated dissociation, fragment ions of selected molecular ion precursors showed structural features indicative of the presence of hydroxyl groups, ring systems, ester groups, and aldehyde groups and the extent of aliphatic polyene conjugation. The fragmentation patterns observed in the mass spectra herein may be used as a reference for the structural determination of carotenoids isolated from plant and animal tissues. 18 refs., 4 figs.

On possibility of degradation of lava-like fuel-containing materials of the 4-th block of Chernobyl NPP under internal self-irradiation by alpha-particle sources

International Nuclear Information System (INIS)

Pazukhin, Eh. M.; Borovoj, A.A.; Rudya, K.G.

2002-01-01

It is shown that internal self-irradiation by alpha-particle beam cannot be a cause of change of strength characteristics of silicate matrix and so a cause of degradation of Chernobyl lava-like materials. A new method is proposed for management with lava-like fuel-containing materials of the 4-th block: vitrification in smelter unit situated in bubbler-basin and storage of prepared immobilized compacts in corresponding depositories [ru

Synthesis and Characterization of Stimuli Responsive Block Copolymers, Self-Assembly Behavior and Applications

Energy Technology Data Exchange (ETDEWEB)

Determan, Michael Duane [Iowa State Univ., Ames, IA (United States)

2005-12-17

The central theme of this thesis work is to develop new block copolymer materials for biomedical applications. While there are many reports of stimuli-responsive amphiphilic [19-21] and crosslinked hydrogel materials [22], the development of an in situ gel forming, pH responsive pentablock copolymer is a novel contribution to the field, Figure 1.1 is a sketch of an ABCBA pentablock copolymer. The A blocks are cationic tertiary amine methacrylates blocked to a central Pluronic F127 triblock copolymer. In addition to the prerequisite synthetic and macromolecular characterization of these new materials, the self-assembled supramolecular structures formed by the pentablock were experimentally evaluated. This synthesis and characterization process serves to elucidate the important structure property relationships of these novel materials, The pH and temperature responsive behavior of the pentablock copolymer were explored especially with consideration towards injectable drug delivery applications. Future synthesis work will focus on enhancing and tuning the cell specific targeting of DNA/pentablock copolymer polyplexes. The specific goals of this research are: (1) Develop a synthetic route for gel forming pentablock block copolymers with pH and temperature sensitive properties. Synthesis of these novel copolymers is accomplished with ATRP, yielding low polydispersity and control of the block copolymer architecture. Well defined macromolecular characteristics are required to tailor the phase behavior of these materials. (2) Characterize relationship between the size and shape of pentablock copolymer micelles and gel structure and the pH and temperature of the copolymer solutions with SAXS, SANS and CryoTEM. (3) Evaluate the temperature and pH induced phase separation and macroscopic self-assembly phenomenon of the pentablock copolymer. (4) Utilize the knowledge gained from first three goals to design and formulate drug delivery formulations based on the multi

Space Environmental Effects on Coated Tether Materials

Science.gov (United States)

Gittemeier, Keith A.; Hawk, Clark W.; Finckenor, Miria M.; Watts, Ed

2005-01-01

The University of Alabama in Huntsville s Propulsion Research Center has teamed with NASA's Marshall Space Flight Center (MSFC) to research the effects of atomic oxygen (AO) bombardment on coated tether materials. Tethers Unlimited Inc. has provided several candidate tether materials with various coatings for AO exposure in MSFC s Atomic Oxygen Beam Facility. Additional samples were exposed to ultraviolet (UV) radiation at MSFC. AO erodes most organic materials, and ultraviolet radiation embrittles polymers. This test series was performed to determine the effect of AO and UV on the mechanical integrity of tether materials that were treated with AO-protective coatings, such as polyhedral oligomeric silsesquioxane (POSS) or metallization. Both TUI's Multi-Application Survivable Tether (MAST) Experiment and Marshall Space Flight Center s Momentum Exchange Electrodynamic Reboost (MXER) programs will benefit from this research by helping to determine tether materials and coatings that give the longest life with the lowest mass penalty.

Effect of Compaction on Compressive Strength of Unfired Clay Blocks

International Nuclear Information System (INIS)

Lakho, N.A.; Zardari, M.A.; Pathan, A.A.

2016-01-01

This study investigates the possible use of unfired compacted clay blocks as a substitute of CSEB (Compressed Stabilized Earth Blocks) for the construction of economical houses. Cubes of 150 mm size were cut from the clay blocks which were compacted at various intensities of pressure during the casting. The results show that the compressive strength of the clay cubes increased with the compacting pressure to which the blocks were subjected during casting. The average crushing strength of the cubes, sawed from clay blocks that were subjected to compacting pressure of 7.2 MPa, was found to be 4.4 MPa. This value of compressive strength is about 50 percent more than that of normal CSEB. This study shows that the compacted clay blocks could be used as economical walling material as replacement of CSEB. (author)

Elastic scattering, inelastic scattering, and transfer reactions induced by 12C bombardment of 12C

International Nuclear Information System (INIS)

Stokstad, R.G.; Wieland, R.M.; Fulmer, C.B.; Hensley, D.C.; Raman, S.; Snell, A.H.; Stelson, P.H.

1977-06-01

Graphs and tables of differential cross sections are presented for the elastic scattering of 12 C by 12 C, the single excitation (Q = -4.43 MeV) and the mutual excitation (Q = -8.86 MeV) for 14 bombarding energies in the range 70.7 less than or equal to E/sub lab/ less than or equal to 126.7 MeV. Differential cross sections for one- and two-nucleon transfer are presented for E/sub lab/ = 93.8 MeV

Material selection and embodied energy

CSIR Research Space (South Africa)

Ampofo-Anti, N

2010-11-01

Full Text Available mix concrete apron Non reinforced, ready mix concrete strip foundation Non reinforced, ready mix ground floor slab Concrete block Modular, hollow concrete block Solid concrete block Finishes Floor screed Insulated ceiling panel Perlite... Predicting the embodied energy contribution of a single material is however not as easy as green building practices assume. As illustrated by the example in Box 1, the choice of a material implies the choice of integral constituents such as insulation...

Testing block subdivision algorithms on block designs

Science.gov (United States)

Wiseman, Natalie; Patterson, Zachary

2016-01-01

Integrated land use-transportation models predict future transportation demand taking into account how households and firms arrange themselves partly as a function of the transportation system. Recent integrated models require parcels as inputs and produce household and employment predictions at the parcel scale. Block subdivision algorithms automatically generate parcel patterns within blocks. Evaluating block subdivision algorithms is done by way of generating parcels and comparing them to those in a parcel database. Three block subdivision algorithms are evaluated on how closely they reproduce parcels of different block types found in a parcel database from Montreal, Canada. While the authors who developed each of the algorithms have evaluated them, they have used their own metrics and block types to evaluate their own algorithms. This makes it difficult to compare their strengths and weaknesses. The contribution of this paper is in resolving this difficulty with the aim of finding a better algorithm suited to subdividing each block type. The proposed hypothesis is that given the different approaches that block subdivision algorithms take, it's likely that different algorithms are better adapted to subdividing different block types. To test this, a standardized block type classification is used that consists of mutually exclusive and comprehensive categories. A statistical method is used for finding a better algorithm and the probability it will perform well for a given block type. Results suggest the oriented bounding box algorithm performs better for warped non-uniform sites, as well as gridiron and fragmented uniform sites. It also produces more similar parcel areas and widths. The Generalized Parcel Divider 1 algorithm performs better for gridiron non-uniform sites. The Straight Skeleton algorithm performs better for loop and lollipop networks as well as fragmented non-uniform and warped uniform sites. It also produces more similar parcel shapes and patterns.

Rapid ordering of block copolymer thin films

International Nuclear Information System (INIS)

Majewski, Pawel W; Yager, Kevin G

2016-01-01

Block-copolymers self-assemble into diverse morphologies, where nanoscale order can be finely tuned via block architecture and processing conditions. However, the ultimate usage of these materials in real-world applications may be hampered by the extremely long thermal annealing times—hours or days—required to achieve good order. Here, we provide an overview of the fundamentals of block-copolymer self-assembly kinetics, and review the techniques that have been demonstrated to influence, and enhance, these ordering kinetics. We discuss the inherent tradeoffs between oven annealing, solvent annealing, microwave annealing, zone annealing, and other directed self-assembly methods; including an assessment of spatial and temporal characteristics. We also review both real-space and reciprocal-space analysis techniques for quantifying order in these systems. (topical review)

Block Play and Mathematics Learning in Preschool: The Effects of Building Complexity, Peer and Teacher Interactions in the Block Area, and Replica Play Materials

Science.gov (United States)

Trawick-Smith, Jeffrey; Swaminathan, Sudha; Baton, Brooke; Danieluk, Courtney; Marsh, Samantha; Szarwacki, Monika

2017-01-01

Block play has been included in early childhood classrooms for over a century, yet few studies have examined its effects on learning. Several previous investigations indicate that the complexity of block building is associated with math ability, but these studies were often conducted in adult-guided, laboratory settings. In the present…

Study of the point defects formed in cobalt by electron bombardment; Etude des defauts ponctuels crees par bombardement electronique dans le cobalt

Energy Technology Data Exchange (ETDEWEB)

Sulpice, G [Commissariat a l' Energie Atomique, 38 - Grenoble (France). Centre d' Etudes Nucleaires

1968-12-01

A study of the point defects formed in cobalt by electron bombardment is presented. The results are compared with those previously obtained for two other ferromagnetic metals of different structure, iron and nickel. In the first part we give a review of the literature concerning the creation of point defects, their contribution to resistivity and their annihilation mode in the three structure types. We then describe the experimental techniques adapted, in particular the study of the resistivity increase during a linear temperature rise. Our investigations concern the following, essential points : the observation of the successive annihilation stages of the point defects formed in pure cobalt, a study of the variations with respect to the doses and energy of the incident particles, and the determination of the annealing kinetics and the corresponding activation energies. The results are finally compared with the various models of point defect annihilation proposed for other metals: none of these interpretations is in perfect agreement with our results. In the case of cobalt we are thus led to modify the model proposed by our laboratory for iron an nickel. The difference between these three metals is explained by the anisotropic character of the cobalt matrix. (author) [French] Nous presentons une etude des defauts ponctuels crees par bombardement electronique dans le cobalt et comparons nos resultats a ceux obtenus precedemment dans deux autres metaux ferromagnetiques de structure differente, le fer et le nickel. Dans une premiere partie nous faisons une mise au point bibliographique comparee sur la creation des defauts, leur contribution a la resistivite et leur mode d'annihilation dans les trois types de structure. Nous decrivons ensuite les techniques experimentales mises au point, en particulier l'etude du revenu de la resistivite au cours d'une montee lineaire de temperature. Au cours de ce travail, nous avons mis en evidence les stades successifs d

Vertical Ridge Augmentation of the Atrophic Posterior Mandible with Sandwich Technique: Bone Block from the Chin Area versus Corticocancellous Bone Block Allograft—Clinical and Histological Prospective Randomized Controlled Study

Directory of Open Access Journals (Sweden)

Luigi Laino

2014-01-01

Full Text Available The aim of the present study is to compare the histological aspects of bone formation in atrophic posterior mandibles augmented by autologous bone block from chin area with corticocancellous bone block allograft used as inlays with the sandwich technique. Materials and Methods. Sixteen patients with bilateral partial edentulism in the posterior mandible were selected. The residual bone height, preliminarily measured by computed tomography scans, ranged between 5 and 7 mm from the inferior alveolar nerve. All patients required regeneration procedure with autologous bone block from chin area (control group versus bone block allograft Puros (Zimmer Dental, 1900 Aston Avenue, Carlsbad, CA, USA (test group. Histological and histomorphometric samples were collected at the time of implant positioning in order to analyze the percentage of newly formed bone, the residual graft material, and marrow spaces/soft tissue. Results. No statistically significant differences between the two groups were found regarding the percentage of newly formed bone. The percentage of residual grafted material was significantly higher in the test group, whilst the percentage of marrow spaces was higher in control group. Conclusions. In conclusion, both procedures supported good results, although the use of bone blocks allograft was less invasive and preferable than harvesting bone from the mental symphysis.

MHSS: a material handling system simulator

Energy Technology Data Exchange (ETDEWEB)

Pomernacki, L.; Hollstien, R.B.

1976-04-07

A Material Handling System Simulator (MHSS) program is described that provides specialized functional blocks for modeling and simulation of nuclear material handling systems. Models of nuclear fuel fabrication plants may be built using functional blocks that simulate material receiving, storage, transport, inventory, processing, and shipping operations as well as the control and reporting tasks of operators or on-line computers. Blocks are also provided that allow the user to observe and gather statistical information on the dynamic behavior of simulated plants over single or replicated runs. Although it is currently being developed for the nuclear materials handling application, MHSS can be adapted to other industries in which material accountability is important. In this paper, emphasis is on the simulation methodology of the MHSS program with application to the nuclear material safeguards problem. (auth)

Annealing of defects in indium antimonide after ion bombardment

International Nuclear Information System (INIS)

Bogatyrev, V.A.; Kachurin, G.A.

1977-01-01

Indium antimonide electric properties are investigated after ion bombardment of different mass (with energy of 60 and 300 keV) and isochrone annealing in the 20-450 deg C temperature range. It is shown that 100-150 deg C n- type stable layers are formed after proton irradiation at room temperature only. Indium antimonide exposure by average mass ions under the same conditions and also by helium ions of 300 keV energy brings to p-type layer formation with high hole concentration. Subsequent heating at the temperature over 150 deg C results in electron conductivity of irradiated layers. Electron volume density and mobility efficiency reaches 10 18 cm -3 and 10 4 cm 2 /Vs respectively. N-type formed layers are stable up to 350 deg C allowing its usage for n-p transition formation admitting thermal treatment. Analysis is given of defect behaviour peculiarities depending upon the irradiation and annealing conditions. Hole conductivity in irradiated indium antimonide is supposed to be stipulated by regions of disorder, while electron conductivity - by relatively simpler disorders

Using MDECR-PECVD to study the impact of ion bombardment energy on microstructural properties of μc-Si:H thin film grown from an SiF{sub 4}/H{sub 2} chemistry

Energy Technology Data Exchange (ETDEWEB)

Wang, Junkang; Florea, Ileana; Bulkin, Pavel V.; Maurice, Jean-Luc; Johnson, Erik V. [LPICM, CNRS, Ecole Polytechnique, Universite Paris Saclay, 91128 Palaiseau (France)

2016-12-15

The matrix-distributed electron cyclotron resonance plasma-enhanced chemical vapor deposition (MDECR-PECVD) technique has been shown to achieve high deposition rates for hydrogenated microcrystalline silicon (μc-Si:H) thin film. Due to the fact that plasma is sustained by a microwave discharge, by biasing the substrate holder with additional power supply, one can achieve independent control over the plasma density and the maximum ion bombardment energy (IBE). In this work, we present studies of the impact of IBE on the microstructural properties of the μc-Si:H film deposited by MDECR-PECVD. Insufficient ion bombardment is found to be responsible for the substantial presence of nano-porous regions within the material, resulting in significant post-deposition oxidation. Good agreement between transmission electron microscopy (TEM) Fresnel contrast analysis and the results of infrared absorption and hydrogen effusion measurements for the deposited films suggest that moderate IBE is of vital importance to achieve high quality μc-Si:H. In doing so, denser films with significantly decreased nano-porous regions and better stability are obtained, which is of great interest to optimize the process parameters for solar cell applications. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Efficient and stable transformation of hop (Humulus lupulus L.) var. Eroica by particle bombardment.

Science.gov (United States)

Batista, Dora; Fonseca, Sandra; Serrazina, Susana; Figueiredo, Andreia; Pais, Maria Salomé

2008-07-01

To the best of our knowledge, this is the first accurate and reliable protocol for hop (Humulus lupulus L.) genetic transformation using particle bombardment. Based on the highly productive regeneration system previously developed by us for hop var. Eroica, two efficient transformation protocols were established using petioles and green organogenic nodular clusters (GONCs) bombarded with gusA reporter and hpt selectable genes. A total of 36 hygromycin B-resistant (hyg(r)) plants obtained upon continuous selection were successfully transferred to the greenhouse, and a first generation group of transplanted plants was followed after spending a complete vegetative cycle. PCR analysis showed the presence of one of both transgenes in 25 plants, corresponding to an integration frequency of 69.4% and an overall transformation efficiency of 7.5%. Although all final transformants were GUS negative, the integration frequency of gusA gene was higher than that of hpt gene. Petiole-derived transgenic plants showed a higher co-integration rate of 76.9%. Real-time PCR analysis confirmed co-integration in 86% of the plants tested and its stability until the first generation, and identified positive plants amongst those previously assessed as hpt (+) only by conventional PCR. Our results suggest that the integration frequencies presented here, as well as those of others, may have been underestimated, and that PCR results should be taken with precaution not only for false positives, but also for false negatives. The protocols here described could be very useful for future introduction of metabolic or resistance traits in hop cultivars even if slight modifications for other genotypes are needed.

Life Cycle CO2 Assessment by Block Type Changes of Apartment Housing

Directory of Open Access Journals (Sweden)

Cheonghoon Baek

2016-08-01

Full Text Available The block type and structural systems in buildings affect the amount of building materials required as well as the CO2 emissions that occur throughout the building life cycle (LCCO2. The purpose of this study was to assess the life cycle CO2 emissions when an apartment housing with ‘flat-type’ blocks (the reference case was replaced with more sustainable ‘T-type’ blocks with fewer CO2 emissions (the alternative case maintaining the same total floor area. The quantity of building materials used and building energy simulations were analyzed for each block type using building information modeling techniques, and improvements in LCCO2 emission were calculated by considering high-strength concrete alternatives. By changing the bearing wall system of the ‘flat-type’ block to the ‘column and beam’ system of the ‘T-type’ block, LCCO2 emissions of the alternative case were 4299 kg-CO2/m2, of which 26% was at the construction stage, 73% was as the operational stage and 1% was at the dismantling and disposal stage. These total LCCO2 emissions were 30% less than the reference case.

Anomalous time-of-flight distributions observed for argon implanted in silicon and resputtered by Ar+-ion bombardment

International Nuclear Information System (INIS)

van Veen, G.N.A.; Sanders, F.H.M.; Dieleman, J.; van Veen, A.; Oostra, D.J.; de Vries, A.E.

1986-01-01

A Si substrate is bombarded by 3-keV Ar + ions. From time-of-flight spectra of resputtered Ar neutrals at various target temperatures, we conclude that Ar-bubble formation takes place in the amorphized-Si top layer. The bubbles form and open during etching. The average kinetic energy of the Ar atoms is in agreement with the calculated average potential energy of the Ar atoms inside the bubbles

Regional anesthesia in transurethral resection of prostate (TURP surgery: A comparative study between saddle block and subarachnoid block

Directory of Open Access Journals (Sweden)

Susmita Bhattacharyya

2015-01-01

Full Text Available Background: Spinal anesthesia is the technique of choice in transurethral resection of prostate (TURP. The major complication of spinal technique is risk of hypotension. Saddle block paralyzed pelvic muscles and sacral nerve roots and hemodynamic derangement is less. Aims and objectives: To compare the hemodynamic changes and adequate surgical condition between saddle block and subarachnoid block for TURP. Material and methods: Ninety patients of aged between 50 to 70 years of ASA-PS I, II scheduled for TURP were randomly allocated into 2 groups of 45 in each group. Group A patients were received spinal (2 ml of hyperbaric bupivacaine and Group B were received saddle block (2 ml of hyperbaric bupivacaine. Baseline systolic, diastolic and mean arterial pressure, heart rate, oxygen saturation were recorded and measured subsequently. The height of block was noted in both groups. Hypotension was corrected by administration of phenylephrine 50 mcg bolus and total requirement of vasopressor was noted. Complications (volume overload, TURP syndrome etc. were noted. Results: Incidence of hypotension and vasopressor requirement was less (P < 0.01 in Gr B patients.Adequate surgical condition was achieved in both groups. There was no incidence of volume overload, TURP syndrome, and bladder perforation. Conclusion: TURP can be safely performed under saddle block without hypotension and less vasopressor requirement.

Cutaneous Sensory Block Area, Muscle-Relaxing Effect, and Block Duration of the Transversus Abdominis Plane Block

DEFF Research Database (Denmark)

Støving, Kion; Rothe, Christian; Rosenstock, Charlotte V

2015-01-01

BACKGROUND AND OBJECTIVES: The transversus abdominis plane (TAP) block is a widely used nerve block. However, basic block characteristics are poorly described. The purpose of this study was to assess the cutaneous sensory block area, muscle-relaxing effect, and block duration. METHODS: Sixteen...... healthy volunteers were randomized to receive an ultrasound-guided unilateral TAP block with 20 mL 7.5 mg/mL ropivacaine and placebo on the contralateral side. Measurements were performed at baseline and 90 minutes after performing the block. Cutaneous sensory block area was mapped and separated...... into a medial and lateral part by a vertical line through the anterior superior iliac spine. We measured muscle thickness of the 3 lateral abdominal muscle layers with ultrasound in the relaxed state and during maximal voluntary muscle contraction. The volunteers reported the duration of the sensory block...

Low-energy ion bombardment of frozen bacterial spores and its relevance to interplanetary space

Energy Technology Data Exchange (ETDEWEB)

Tuleta, M.; Gabla, L. [Jagiellonian Univ., Institute of Physics, Cracow (Poland); Szkarlat, A. [Clinical Children' s Hospital of the Jagiellonian Univ., Medical College, Lab. of Microbiology, Cracow (Poland)

2005-04-01

The panspermia hypothesis is concerned with the dissemination of life in space in the form of simple micro-organisms. During an interplanetary journey the micro-organisms are subjected to the action of, among others, the solar wind. We have simulated experimentally such conditions bombarding frozen bacterial spores with low-energy hydrogen ions. On the basis of the results obtained and our earlier research, a new look at the panspermia hypothesis is discussed. The general conclusion is that unprotected naked spores, their conglomerates and protected spores can survive attack of the solar wind, although to various degrees. (authors)

Low-energy ion bombardment of frozen bacterial spores and its relevance to interplanetary space

International Nuclear Information System (INIS)

Tuleta, M.; Gabla, L.; Szkarlat, A.

2005-01-01

The panspermia hypothesis is concerned with the dissemination of life in space in the form of simple micro-organisms. During an interplanetary journey the micro-organisms are subjected to the action of, among others, the solar wind. We have simulated experimentally such conditions bombarding frozen bacterial spores with low-energy hydrogen ions. On the basis of the results obtained and our earlier research, a new look at the panspermia hypothesis is discussed. The general conclusion is that unprotected naked spores, their conglomerates and protected spores can survive attack of the solar wind, although to various degrees. (authors)

Synthesis of Inorganic Nanocomposites by Selective Introduction of Metal Complexes into a Self-Assembled Block Copolymer Template

Directory of Open Access Journals (Sweden)

Hiroaki Wakayama

2015-01-01

Full Text Available Inorganic nanocomposites have characteristic structures that feature expanded interfaces, quantum effects, and resistance to crack propagation. These structures are promising for the improvement of many materials including thermoelectric materials, photocatalysts, and structural materials. Precise control of the inorganic nanocomposites’ morphology, size, and chemical composition is very important for these applications. Here, we present a novel fabrication method to control the structures of inorganic nanocomposites by means of a self-assembled block copolymer template. Different metal complexes were selectively introduced into specific polymer blocks of the block copolymer, and subsequent removal of the block copolymer template by oxygen plasma treatment produced hexagonally packed porous structures. In contrast, calcination removal of the block copolymer template yielded nanocomposites consisting of metallic spheres in a matrix of a metal oxide. These results demonstrate that different nanostructures can be created by selective use of processes to remove the block copolymer templates. The simple process of first mixing block copolymers and magnetic nanomaterial precursors and then subsequently removing the block copolymer template enables structural control of magnetic nanomaterials, which will facilitate their applicability in patterned media, including next-generation perpendicular magnetic recording media.

Stepwise transformation of the molecular building blocks in a porphyrin-encapsulating metal-organic material

KAUST Repository

Zhang, ZhenJie

2013-04-24

When immersed in solutions containing Cu(II) cations, the microporous metal-organic material P11 ([Cd4(BPT)4]·[Cd(C 44H36N8)(S)]·[S], BPT = biphenyl-3,4′,5-tricarboxylate) undergoes a transformation of its [Cd 2(COO)6]2- molecular building blocks (MBBs) into novel tetranuclear [Cu4X2(COO)6(S) 2] MBBs to form P11-Cu. The transformation occurs in single-crystal to single-crystal fashion, and its stepwise mechanism was studied by varying the Cd2+/Cu2+ ratio of the solution in which crystals of P11 were immersed. P11-16/1 (Cd in framework retained, Cd in encapsulated porphyrins exchanged) and other intermediate phases were thereby isolated and structurally characterized. P11-16/1 and P11-Cu retain the microporosity of P11, and the relatively larger MBBs in P11-Cu permit a 20% unit cell expansion and afford a higher surface area and a larger pore size. © 2013 American Chemical Society.

31 CFR 594.301 - Blocked account; blocked property.

Science.gov (United States)

2010-07-01

... (Continued) OFFICE OF FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY GLOBAL TERRORISM SANCTIONS REGULATIONS General Definitions § 594.301 Blocked account; blocked property. The terms blocked account and...

Modulation transfer function and detective quantum efficiency of electron bombarded charge coupled device detector for low energy electrons

International Nuclear Information System (INIS)

Horacek, Miroslav

2005-01-01

The use of a thinned back-side illuminated charge coupled device chip as two-dimensional sensor working in direct electron bombarded mode at optimum energy of the incident signal electrons is demonstrated and the measurements of the modulation transfer function (MTF) and detective quantum efficiency (DQE) are described. The MTF was measured for energy of electrons 4 keV using an edge projection method and a stripe projection method. The decrease of the MTF for a maximum spatial frequency of 20.8 cycles/mm, corresponding to the pixel size 24x24 μm, is 0.75≅-2.5 dB, and it is approximately the same for both horizontal and vertical directions. DQE was measured using an empty image and the mixing factor method. Empty images were acquired for energies of electrons from 2 to 5 keV and for various doses, ranging from nearly dark image to a nearly saturated one. DQE increases with increasing energy of bombarded electrons and reaches 0.92 for electron energy of 5 keV. For this energy the detector will be used for the angle- and energy-selective detection of signal electrons in the scanning low energy electron microscope

Transmitting Memory between and beyond Generations: The Rotterdam Bombardment in Local Memory Culture and Education from 1980 to 2015

Science.gov (United States)

Hogervorst, Susan

2015-01-01

This article analyses three local educational projects about the Nazi bombing of Rotterdam in May 1940, all of which took place from 1980 to the present day in the context of the dynamic memory culture of the bombardment. These three contexts testify to a process by which memory, increasingly derived from authentic locations and objects instead of…

Hippocampal activation during face-name associative memory encoding: blocked versus permuted design

International Nuclear Information System (INIS)

De Vogelaere, Frederick; Vingerhoets, Guy; Santens, Patrick; Boon, Paul; Achten, Erik

2010-01-01

The contribution of the hippocampal subregions to episodic memory through the formation of new associations between previously unrelated items such as faces and names is established but remains under discussion. Block design studies in this area of research generally tend to show posterior hippocampal activation during encoding of novel associational material while event-related studies emphasize anterior hippocampal involvement. We used functional magnetic resonance imaging to assess the involvement of anterior and posterior hippocampus in the encoding of novel associational material compared to the viewing of previously seen associational material. We used two different experimental designs, a block design and a permuted block design, and applied it to the same associative memory task to perform valid statistical comparisons. Our results indicate that the permuted design was able to capture more anterior hippocampal activation compared to the block design, which emphasized more posterior hippocampal involvement. These differences were further investigated and attributed to a combination of the polymodal stimuli we used and the experimental design. Activation patterns during encoding in both designs occurred along the entire longitudinal axis of the hippocampus, but with different centers of gravity. The maximal activated voxel in the block design was situated in the posterior half of the hippocampus while in the permuted design this was located in the anterior half. (orig.)

Hippocampal activation during face-name associative memory encoding: blocked versus permuted design

Energy Technology Data Exchange (ETDEWEB)

De Vogelaere, Frederick; Vingerhoets, Guy [Ghent University, Laboratory for Neuropsychology, Department of Neurology, Ghent (Belgium); Santens, Patrick; Boon, Paul [Ghent University Hospital, Department of Neurology, Ghent (Belgium); Achten, Erik [Ghent University Hospital, Department of Radiology, Ghent (Belgium)

2010-01-15

The contribution of the hippocampal subregions to episodic memory through the formation of new associations between previously unrelated items such as faces and names is established but remains under discussion. Block design studies in this area of research generally tend to show posterior hippocampal activation during encoding of novel associational material while event-related studies emphasize anterior hippocampal involvement. We used functional magnetic resonance imaging to assess the involvement of anterior and posterior hippocampus in the encoding of novel associational material compared to the viewing of previously seen associational material. We used two different experimental designs, a block design and a permuted block design, and applied it to the same associative memory task to perform valid statistical comparisons. Our results indicate that the permuted design was able to capture more anterior hippocampal activation compared to the block design, which emphasized more posterior hippocampal involvement. These differences were further investigated and attributed to a combination of the polymodal stimuli we used and the experimental design. Activation patterns during encoding in both designs occurred along the entire longitudinal axis of the hippocampus, but with different centers of gravity. The maximal activated voxel in the block design was situated in the posterior half of the hippocampus while in the permuted design this was located in the anterior half. (orig.)

Evaluation of Environmental and Hydraulic Performance of Bio-Composite Revetment Blocks

OpenAIRE

Thamer A.  Ahmeed; Nor A.  Alias; Abdul H.  Ghazali; Mohd. S.  Jaafar

2006-01-01

It is necessary to develop a concrete revetment block which can cater for environment and at the same time it will be effective in protecting river banks (stabilize the slope of banks) from scouring during flood. In the present study, the environmental and hydraulic performance of the proposed revetment block was evaluated through laboratory and field tests. The tested revetment block is called bio-composite because it is composed of concrete, plastic mesh and biological material (coconut hus...

Traces of warping subsided tectonic blocks on Miranda, Enceladus, Titan

Science.gov (United States)

Kochemasov, G.

2007-08-01

Icy satellites of the outer Solar system have very large range of sizes - from kilometers to thousands of kilometers. Bodies less than 400-500 km across have normally irregular shapes , often presenting simple Plato's polyhedrons woven by standing inertiagravity waves (see an accompanying abstract of Kochemasov). Larger bodies with enhanced gravity normally are rounded off and have globular shapes but far from ideal spheres. This is due to warping action of inertia-gravity waves of various wavelengths origin of which is related to body movements in elliptical keplerian orbits with periodically changing accelerations (alternating accelerations cause periodically changing forces acting upon a body what means oscillations of its spheres in form of standing warping waves). The fundamental wave 1 and its first overtone wave 2 produce ubiquitous tectonic dichotomy - two segmental structure and tectonic sectoring superimposed on this dichotomy. Two kinds of tectonic blocks (segments and sectors) are formed: uplifted (+) and subsided (-). Uplifting means increasing planetary radius of blocks, subsiding - decreasing radius (as a sequence subsiding blocks diminishing their surfaces must be warped, folded, wrinkled; uplifting blocks increasing their surfaces tend to be deeply cracked, fallen apart). To level changing angular momenta of blocks subsided areas are filled with denser material than uplifted ones (one of the best examples is Earth with its oceanic basins filled with dense basalts and uplifted continents built of less dense on average andesitic material). Icy satellites follow the same rule. Their warped surfaces show differing chemistries or structures of constructive materials. Uplifted blocks are normally built with light (by color and density) water ice. Subsided blocks - depressions, "seas', "lakes", coronas - by somewhat denser material differing in color from water ice (very sharply - Iapetus, moderately - Europa, slightly - many saturnian satellites). A very

Characterizing the X-ray & Stellar Wind Environment in the ~1 Gyr Late Heavy Bombardment System Eta Corvi

Science.gov (United States)

Lisse, Carey

2012-09-01

We propose a 40 ksec ACIS-S observation of the 1 Gyr old system Eta Corvi, the site of an on-going Late Heavy Bombardment (Lisse et al. 2012), in order to determine the spectrum of x-ray radiation in the burgeoning system, its origin in the stellar coronae and circumstellar debris belts, and its impact on the water and organics recently delivered to a rocky planet in the terrestrial habitability zone.

["Habitual" left branch block alternating with 2 "disguised" bracnch block].

Science.gov (United States)

Lévy, S; Jullien, G; Mathieu, P; Mostefa, S; Gérard, R

1976-10-01

Two cases of alternating left bundle branch block and "masquerading block" (with left bundle branch morphology in the stnadard leads and right bundle branch block morphology in the precordial leads) were studied by serial tracings and his bundle electrocardiography. In case 1 "the masquerading" block was associated with a first degree AV block related to a prolongation of HV interval. This case is to our knowledge the first cas of alternating bundle branch block in which his bundle activity was recorded in man. In case 2, the patient had atrial fibrilation and His bundle recordings were performed while differents degrees of left bundle branch block were present: The mechanism of the alternation and the concept of "masquerading" block are discussed. It is suggested that this type of block represents a right bundle branch block associated with severe lesions of the "left system".

Electrochemically assisted fast-atom-bombardment mass spectrometry

International Nuclear Information System (INIS)

Phillips, L.R.

1988-01-01

The hybridization of electrochemistry and fast atom bombardment (FAB) mass spectrometry (MS) creates a new hyphenated technique, referred to as electrochemically assisted FAB (EFAB) MS, which improves the applicability of FAB MS in selectivity and extends the range of compounds to include low polarity molecules, and also reduces mass spectral complications due to matrix-related artifacts. FAB MS has proven to be indispensable in analysis of samples that are otherwise too intractable for conventional MS, such as peptides, oligosaccharides, and oligonucleotides, due to low volatility and ready thermal degradation. There are limits on its applicability, however, in that it works best with samples that are already ionic, or predisposed to become so by simple proton transfer to or from the matrix. A wide range of chemical substances can be ionized/analyzed by electrochemical methods. Therefore, a possible approach towards improving applicability of FAB MS is through its hybridization with electrochemistry. Samples are activated by electrolysis, carried out directly in the sample matrix through use of a modified FAB sample probe which was constructed containing a small electrolytic cell on the tip. In operation, one electrode is held at normal sample-probe/ion-source voltage, while the other electrode can be continuously varied ±15 volts to create electrochemical potentials. Several chemical substances, known to be unresponsive to FAB MS, have been examined by EFAB MS. Resultant spectra generally show a dramatic increases in signal/chemical noise ratio of structurally significant ions when compared to normal FAB spectra

Fabrication and handling of bentonite blocks

International Nuclear Information System (INIS)

1978-06-01

In accordance with the project for the final storage of spent nuclear fuel, the waste will be encapsulated into copper canisters, which will be deposited in a final repository located in rock 500 m below ground level. The canisters will be placed in vertical holes in the bottoms of the tunnels, where the copper cylinders will be surrounded by blocks of highly compacted bentonite. When the blocks are saturated with water and expansion is essentially retained as in the actual case, a very high swelling pressure will arise. The bentonite will be extremely impermeable and thus it will form a barrier against transport of corrosive matters to the canister. The blocks are fabricated by means of cold isostatic pressing of bentonite powder. The base material in the form of powder is enclosed in flexible forms, which are introduced into pressure vessels where the forms are surrounded by oil or water. Thus the powder is compacted into rigid bodies with a bulk density of about 2.2 t/m 3 for ''air dry'' bentonite, which might be compared with a specific density of about 2.7 t/m 3 . The placing of a canister is preceded by piling up bentonite blocks to a level just below the canister lid position, after which the slot around the blocks is filled with bentonite powder. The rest of the blocks are mounted after filling bentonite powder into the inner slot around the canister as well. Finally the storage tunnels will be sealed by filling them with a mixture o02067NRM 0000181 45

Study of associated gamma from niobium under 14. 9 MeV neutron bombardments

Energy Technology Data Exchange (ETDEWEB)

Zhou Hongyu; Yan Yiming; Fan Guoying; Lan Liqiac; Sun Suxu; Wang Qi; Hua Ming; Han Chongzhen; Liu Shuzhenn; Rong Yaning; and others

1989-02-01

The gamma ray spectra from niobium under 14.9 MeV neutron bombardments were measured by means of a pulsed /ital T/(/ital d/, /ital n/)/sup 4/He neutron source, associated particle method, Ge(Li) detector and time-of-flight technique at 7 angles between 30/degree/ and 140/degree/. 79 gamma lines were determined by a high resolution gamma spectrum analysis program, and reaction types and transition levels of 62 lines were roughly assigned. There were 40 ones of 79 lines, which were first found in reactions induced by neutrons. The differential cross sections of every gamma line at 7 angles were determined. It is shown that associated gamma ray emissions from this reaction are basically isotropic.

Supramolecular materials based on hydrogen-bonded polymers

NARCIS (Netherlands)

ten Brinke, Gerrit; Ruokolainen, Janne; Ikkala, Olli; Binder, W

2007-01-01

Combining supramolecular principles with block copolymer self-assembly offers unique possibilities to create materials with responsive and/or tunable properties. The present chapter focuses on supramolecular materials based on hydrogen bonding and (block co-) polymers. Several cases will be

Superalloy Lattice Block Developed for Use in Lightweight, High-Temperature Structures

Science.gov (United States)

Hebsur, Mohan G.; Whittenberger, J. Daniel; Krause, David L.

2003-01-01

Successful development of advanced gas turbine engines for aircraft will require lightweight, high-temperature components. Currently titanium-aluminum- (TiAl) based alloys are envisioned for such applications because of their lower density (4 g/cm3) in comparison to superalloys (8.5 g/cm3), which have been utilized for hot turbine engine parts for over 50 years. However, a recently developed concept (lattice block) by JAMCORP, Inc., of Willmington, Massachusetts, would allow lightweight, high-temperature structures to be directly fabricated from superalloys and, thus, take advantage of their well-known, characterized properties. In its simplest state, lattice block is composed of thin ligaments arranged in a three dimensional triangulated trusslike configuration that forms a structurally rigid panel. Because lattice block can be fabricated by casting, correctly sized hardware is produced with little or no machining; thus very low cost manufacturing is possible. Together, the NASA Glenn Research Center and JAMCORP have extended their lattice block methodology for lower melting materials, such as Al alloys, to demonstrate that investment casting of superalloy lattice block is possible. This effort required advances in lattice block pattern design and assembly, higher temperature mold materials and mold fabrication technology, and foundry practice suitable for superalloys (ref. 1). Lattice block panels have been cast from two different Ni-base superalloys: IN 718, which is the most commonly utilized superalloy and retains its strength up to 650 C; and MAR M247, which possesses excellent mechanical properties to at least 1100 C. In addition to the open-cell lattice block geometry, same-sized lattice block panels containing a thin (1-mm-thick) solid face on one side have also been cast from both superalloys. The elevated-temperature mechanical properties of the open cell and face-sheeted superalloy lattice block panels are currently being examined, and the

Stochastic simulation of destruction processes in self-irradiated materials

Directory of Open Access Journals (Sweden)

T. Patsahan

2017-09-01

Full Text Available Self-irradiation damages resulting from fission processes are common phenomena observed in nuclear fuel containing (NFC materials. Numerous α-decays lead to local structure transformations in NFC materials. The damages appearing due to the impacts of heavy nuclear recoils in the subsurface layer can cause detachments of material particles. Such a behaviour is similar to sputtering processes observed during a bombardment of the material surface by a flux of energetic particles. However, in the NFC material, the impacts are initiated from the bulk. In this work we propose a two-dimensional mesoscopic model to perform a stochastic simulation of the destruction processes occurring in a subsurface region of NFC material. We describe the erosion of the material surface, the evolution of its roughness and predict the detachment of the material particles. Size distributions of the emitted particles are obtained in this study. The simulation results of the model are in a qualitative agreement with the size histogram of particles produced from the material containing lava-like fuel formed during the Chernobyl nuclear power plant disaster.

Design and Synthesis of Network-Forming Triblock Copolymers Using Tapered Block Interfaces

Science.gov (United States)

Kuan, Wei-Fan; Roy, Raghunath; Rong, Lixia; Hsiao, Benjamin S.; Epps, Thomas H.

2012-01-01

We report a strategy for generating novel dual-tapered poly(isoprene-b-isoprene/styrene-b-styrene-b-styrene/methyl methacrylate-b-methyl methacrylate) [P(I-IS-S-SM-M)] triblock copolymers that combines anionic polymerization, atom transfer radical polymerization (ATRP), and Huisgen 1,3-dipolar cycloaddition click chemistry. The tapered interfaces between blocks were synthesized via a semi-batch feed using programmable syringe pumps. This strategy allows us to manipulate the transition region between copolymer blocks in triblock copolymers providing control over the interfacial interactions in our nanoscale phase-separated materials independent of molecular weight and block constituents. Additionally, we show the ability to retain a desirous and complex multiply-continuous network structure (alternating gyroid) in our dual-tapered triblock material. PMID:23066522

E-Block: A Tangible Programming Tool with Graphical Blocks

Directory of Open Access Journals (Sweden)

Danli Wang

2013-01-01

Full Text Available This paper designs a tangible programming tool, E-Block, for children aged 5 to 9 to experience the preliminary understanding of programming by building blocks. With embedded artificial intelligence, the tool defines the programming blocks with the sensors as the input and enables children to write programs to complete the tasks in the computer. The symbol on the programming block's surface is used to help children understanding the function of each block. The sequence information is transferred to computer by microcomputers and then translated into semantic information. The system applies wireless and infrared technologies and provides user with feedbacks on both screen and programming blocks. Preliminary user studies using observation and user interview methods are shown for E-Block's prototype. The test results prove that E-Block is attractive to children and easy to learn and use. The project also highlights potential advantages of using single chip microcomputer (SCM technology to develop tangible programming tools for children.

25 years and still going strong: 2'-O-(pyren-1-yl)methylribonucleotides - versatile building blocks for applications in molecular biology, diagnostics and materials science.

Science.gov (United States)

Hrdlicka, Patrick J; Karmakar, Saswata

2017-11-29

Oligonucleotides (ONs) modified with 2'-O-(pyren-1-yl)methylribonucleotides have been explored for a range of applications in molecular biology, nucleic acid diagnostics, and materials science for more than 25 years. The first part of this review provides an overview of synthetic strategies toward 2'-O-(pyren-1-yl)methylribonucleotides and is followed by a summary of biophysical properties of nucleic acid duplexes modified with these building blocks. Insights from structural studies are then presented to rationalize the reported properties. In the second part, applications of ONs modified with 2'-O-(pyren-1-yl)methyl-RNA monomers are reviewed, which include detection of RNA targets, discrimination of single nucleotide polymorphisms, formation of self-assembled pyrene arrays on nucleic acid scaffolds, the study of charge transfer phenomena in nucleic acid duplexes, and sequence-unrestricted recognition of double-stranded DNA. The predictable binding mode of the pyrene moiety, coupled with the microenvironment-dependent properties and synthetic feasibility, render 2'-O-(pyren-1-yl)methyl-RNA monomers as a promising class of pyrene-functionalized nucleotide building blocks for new applications in molecular biology, nucleic acid diagnostics, and materials science.

Chemical changes induced on a TiO2 surface by electron bombardment

International Nuclear Information System (INIS)

Vergara, L.I.; Passeggi, M.C.G.; Ferron, J.

2007-01-01

We study the TiO 2 (Ti 4+ ) chemical reduction induced by electron bombardment using Auger electron spectroscopy and factor analysis. We show that the electron irradiation of a TiO 2 sample is characterized by the appearance of a lower Ti oxidation state, Ti 2 O 3 (Ti 3+ ), followed by a further deposition of carbon, which is present inevitably in the environment even under ultra-high vacuum conditions. The appearance of C over the surface is found to be a complex mechanism which affects the reduction process through passivation of the electron-induced oxygen desorption and formation of titanium carbide. For very high irradiation doses, we also found that the chemical changes on the surface are stopped due to the deposition of carbon in a graphitic form

E-Block: A Tangible Programming Tool with Graphical Blocks

OpenAIRE

Danli Wang; Yang Zhang; Shengyong Chen

2013-01-01

This paper designs a tangible programming tool, E-Block, for children aged 5 to 9 to experience the preliminary understanding of programming by building blocks. With embedded artificial intelligence, the tool defines the programming blocks with the sensors as the input and enables children to write programs to complete the tasks in the computer. The symbol on the programming block's surface is used to help children understanding the function of each block. The sequence information is transfer...

Production of 95mTc with proton bombardment of 95Mo

International Nuclear Information System (INIS)

Izumo, M.; Matsuoka, H.; Sorita, T.; Nagame, Y.; Sekine, T.; Hata, K.; Baba, S.

1991-01-01

Formation cross sections of 95m Tc and 95g Tc via the 95 Mo (p,n) reaction have been measured to evaluate the production yield of 95m Tc which is expected to be a useful radiotracer of technetium isotopes. It was found from the cross section data that for incident proton energies above 15 MeV, the thick-target yield of 95m Tc was more than 20 μCi/μAh at the end of bombardment and the 95g Tc contamination was less than 1% after 12 d cooling. To examine the separation and purification of 95m Tc from target, we have carried out a test production of 95m Tc using a thick 95 Mo-enriched target. Other reactions of producing 95m Tc are compared and discussed in terms of the production yield and amounts of contaminants. (author)

Amplifying (Im)perfection: The Impact of Crystallinity in Discrete and Disperse Block Co-oligomers.

Science.gov (United States)

van Genabeek, Bas; Lamers, Brigitte A G; de Waal, Bas F M; van Son, Martin H C; Palmans, Anja R A; Meijer, E W

2017-10-25

Crystallinity is seldomly utilized as part of the microphase segregation process in ultralow-molecular-weight block copolymers. Here, we show the preparation of two types of discrete, semicrystalline block co-oligomers, comprising an amorphous oligodimethylsiloxane block and a crystalline oligo-l-lactic acid or oligomethylene block. The self-assembly of these discrete materials results in lamellar structures with unforeseen uniformity in the domain spacing. A systematic introduction of dispersity reveals the extreme sensitivity of the microphase segregation process toward chain length dispersity in the crystalline block.

Usage de la refusion par bombardement électronique pour la purification et le recyclage des alliages Application of the electron beam remelting for the purification and the recycling of alloys

Directory of Open Access Journals (Sweden)

Bellot Jean-Pierre

2013-11-01

Full Text Available Parmi les techniques de purification ultime de métaux à hauts points de fusion, le procédé de refusion par bombardement électronique associe une puissance thermique garantissant la fusion du métal, et une refusion sous vide permettant l'élimination d'impuretés par distillation. Ce papier présente la technique et le potentiel d'élimination par distillation. Among the ultimate purification techniques applied to the high melting point metallic materials, the electron beam remelting process, combining a high thermal power and vacuum, is particularly conducive to volatilization. This paper describes the technique and its efficiency to remove impurities by distillation.

Effect of block composition on thermal properties and melt viscosity of poly[2-(dimethylaminoethyl methacrylate], poly(ethylene oxide and poly(propylene oxide block co-polymers

Directory of Open Access Journals (Sweden)

2011-09-01

Full Text Available To modify the rheological properties of certain commercial polymers, a set of block copolymers were synthesized through oxyanionic polymerization of 2-(dimethylaminoethyl methacrylate to the chain ends of commercial prepolymers, namely poly(ethylene oxide (PEO, poly(ethylene oxide-block-poly(propylene oxide-block-poly(ethylene oxide (PEO-PPO-PEO, and poly(propylene oxide (PPO. The formed block copolymers were analysed with size exclusion chromatography and nuclear magnetic resonance spectroscopy in order to confirm block formation. Thermal characterization of the resulting polymers was done with differential scanning calorimetry. Thermal transition points were also confirmed with rotational rheometry, which was primarily used to measure melt strength properties of the resulting block co-polymers. It was observed that the synthesised poly[2-(dimethylaminoethyl methacrylate]-block (PDM affected slightly the thermal transition points of crystalline PEO-block but the influence was stronger on amorphous PPO-blocks. Frequency sweeps measured above the melting temperatures for the materials confirmed that the pre-polymers (PEO and PEO-PPO-PEO behave as Newtonian fluids whereas polymers with a PDM block structure exhibit clear shear thinning behaviour. In addition, the PDM block increased the melt viscosity when compared with that one of the pre-polymer. As a final result, it became obvious that pre-polymers modified with PDM were in entangled form, in the melted state as well in the solidified form.

Ultrafast recombination in H+ bombarded InP and GaAs: Consequences for the carrier distribution functions

International Nuclear Information System (INIS)

Lamprecht, K.F.; Juen, S.; Hoepfel, R.A.; Palmetshofer, L.

1992-01-01

The authors studied the lifetimes and the luminescence spectra of photoexcited carriers in H + bombarded InP and GaAs for different damage doses by means of femtosecond luminescence spectroscopy. For InP the lifetime decreases down to 95 fs for the highest dose, whereas for GaAs no shorter lifetime than 650 fs could be observed. With decreasing lifetime they observe an increase of the high energy tail of the time-integrated luminescence spectrum which is even inverted for the 95 fs InP sample

Push-and-stick mechanism for charged and excited small cluster emission under ion bombardment

International Nuclear Information System (INIS)

Bitensky, I.S.; Parilis, E.S.; Wojciechowski, I.A.

1992-01-01

The mechanism for the formation, excitation and ionization of small clusters emitted under ion bombardment is discussed. It is shown that the increased degree of ionization for the transition metal dimers, trimers and tetramers can be explained by the existence of an additional effective channel for their formation, namely the associative ionization process. A simple estimate shows that the sticking together of a fast cascade atom and the pushed out surface atom is 30-40 times more effective for dimer formation, than the recombination of two fast atoms. This push-and-stick mechanism of cluster formation could also be effective for the formation of trimers and tetramers. (orig.)

Electrical conductivity of polytetrafluoroethylene in dc and ac electric fields under continuous electron bombardment

International Nuclear Information System (INIS)

Khatipov, S.A.; Turdybekov, K.M.; Milinchuk, V.K.

1993-01-01

A study has been made of the time of the radiation current density in dc and ac (10 2 -5-10 3 Hz) electric fields (10 3 -5-10 5 V/cm) at temperatures from 80 to 393 K and dose rates from 5-10 3 Gy/sec, for PTFE films (50-180 μm) with various thermal prehistories, when exposed to continuous bombardment by 9-MeV electrons. It has been shown that the experimental results cannot be interpreted from the standpoint of free-charge conduction; they can be explained qualitatively within the framework of concepts of inhomogeneous ionization of the substance, due to the formation of short tracks

Restoration and Preservation of Engraved Limestone Blocks Discovered in Abu Mousa Excavation, Suez - Egypt

Directory of Open Access Journals (Sweden)

Nabil A. Abd El-Tawab BADER

2013-03-01

Full Text Available A lot of engraved limestone blocks were discovered at Awlad Abu Musa (east of Suez, Egypt in 1995/2007 by Supreme Council of Antiquities. The stone blocks were seriously affected by archaeological environments during burial environment in agriculture land. They were covered with thick clay layer with soil particles that disfigured them and hid their inscriptions. Prior to the conservation intervention, the materials were characterized by X-ray diffraction, optical microscopy, scanning electron microscopy with energy-dispersive X-ray spectroscopy, Chemical analyses of ground water and microbiological study. After the material characterization, the conservation and restoration of the stone blocks were carried out including cleaning, consolidation, reduction of salts, Re-jointing, restoration and completion of lost parts. After that the blocks were exhibited in Suez museum.

The Market Gate of Miletus: damages, material characteristics and the development of a compatible mortar for restoration

Science.gov (United States)

Siegesmund, Siegfried; Middendorf, Bernhard

2008-12-01

The indoor exhibit of the Market Gate of Miletus is unique for an archaeological monument. The reconstruction of the gate was done in such a way that most marble fragments were removed leaving cored marble columns 3-4 cm in thickness. These cored columns were mounted on a steel construction and filled with different mortars or filled with specially shaped blocks of brick combined with mortar. All the missing marble elements were replaced by copies made of a Portland cement based concrete, which is compositionally similar to the original building materials. During the Second World War the monument was heavily damaged by aerial bombardment. For 2 years the Market Gate of Miletus was exposed to weathering, because a brick wall protecting the gate was also destroyed. The deterioration phenomena observed are microcracks, macroscopic fractures, flaking, sugaring, greying, salt efflorescence, calcitic-sinter layers and iron oxide formation etc. The rapid deterioration seems to be due to indoor atmospheric effects, and also by a combination of incompatible materials (e.g. marble, steel, mortar, concrete, bricks etc.). Compatible building materials like mortars or stone replacing materials have to be developed for the planned restoration. The requirements for restoration mortars are chemical-mineralogical and physical-mechanical compatibilities with the existing building materials. In detail this means that the mortar should ensure good bonding properties, adapted strength development and not stain the marble when in direct contact. The favoured mortar was developed with a hydraulic binder based on iron-free white cement and pozzolana based on activated clay. A special limestone and quartz sand mixture was used as an aggregate. The cement was adjusted using chemical additives. Specially designed tests were applied extensively to prove whether the developed mortar is suitable for the restoration of this precious monument.

Study of the machining of uranium carbide rods obtained by continuous casting under electronic bombardment; Etude de l'usinage de barreaux de carbure d'uranium obtenus par coulee continue sous bombardement electronique

Energy Technology Data Exchange (ETDEWEB)

Rousset, P; Accary, A [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1965-07-01

The authors consider the various methods of machining uranium mono-carbide and compare them critically in the case of their application to uranium carbide obtained by fusion under an electronic bombardment and continuous casting. This study leads them to propose two mechanical machining methods: cylindrical rectification and center-less rectification, preceded by a preliminary roughing out of a cylinder, the latter appearing more suitable. A study of the machining yields as a function of the diameter of the rough bars and of the diameter of the finished rods has shown that an optimum value of the rough bar diameter exists for each value of the finished rod diameter. It is found that the yield increases as the diameter itself increases, this yield rising from 45 per cent to around 70 per cent as the diameter of the rough bars increases from 25-26 mm to 37-38 mm. (authors) [French] Les auteurs envisagent les differentes methodes d'usinage du monocarbure d'uranium et se livrent a une etude critique de celles-ci, dans le cas de leur application a l'usinage de barreaux de carbure d'uranium obtenus par fusion sous bombardement electronique et coulee continue. Cette etude les conduit a proposer deux methodes d'usinage mecanique: la rectification cylindrique et la rectification 'centerless', precedee d'un ebauchage par carottage, la seconde paraissant la plus appropriee. L'etude des rendements d'usinage en fonction du diametre des barreaux bruts et du diametre des barreaux finis, a mis en evidence une valeur optimale du diametre des barreaux bruts pour chaque valeur du diametre des barreaux usines. Elle a montre que le rendement croit lorsque le diametre croit lui-meme, ce rendement passant d'environ 45 pour cent a environ 70 pour cent, lorsque le diametre des barreaux bruts passe de 25-26 mm a 37-38 mm.

System for studying a sample of material using a heavy ion induced mass spectrometer source

Science.gov (United States)

Fries, D.P.; Browning, J.F.

1998-07-21

A heavy ion generator is used with a plasma desorption mass spectrometer to provide an appropriate neutron flux in the direction of a fissionable material in order to desorb and ionize large molecules from the material for mass analysis. The heavy ion generator comprises a fissionable material having a high (n,f) reaction cross section. The heavy ion generator also comprises a pulsed neutron generator that is used to bombard the fissionable material with pulses of neutrons, thereby causing heavy ions to be emitted from the fissionable material. These heavy ions impinge on a material, thereby causing ions to desorb off that material. The ions desorbed off the material pass through a time-of-flight mass analyzer, wherein ions can be measured with masses greater than 25,000 amu. 3 figs.

Method for studying a sample of material using a heavy ion induced mass spectrometer source

Science.gov (United States)

Fries, D.P.; Browning, J.F.

1999-02-16

A heavy ion generator is used with a plasma desorption mass spectrometer to provide an appropriate neutron flux in the direction of a fissionable material in order to desorb and ionize large molecules from the material for mass analysis. The heavy ion generator comprises a fissionable material having a high n,f reaction cross section. The heavy ion generator also comprises a pulsed neutron generator that is used to bombard the fissionable material with pulses of neutrons, thereby causing heavy ions to be emitted from the fissionable material. These heavy ions impinge on a material, thereby causing ions to desorb off that material. The ions desorbed off the material pass through a time-of-flight mass analyzer, wherein ions can be measured with masses greater than 25,000 amu. 3 figs.

Investigation of energy thresholds of atomic and cluster sputtering of some elements under ion bombardment

CERN Document Server

Atabaev, B G; Lifanova, L F

2002-01-01

Threshold energies of sputtering of negative cluster ions from the Si(111) surface were measured at bombardment by Cs sup + , Rb sup + , and Na sup + ions with energy of 0.1-3.0 keV. These results are compared with the calculations of the similar thresholds by Bohdansky etc. formulas (3) for clusters Si sub n sup - and Cu sub n sup - with n=(1-5) and also for B, C, Al, Si, Fe, Cu atoms. Threshold energies of sputtering for the above elements were also estimated using the data from (5). Satisfactory agreement between the experimental and theoretical results was obtained. (author)

Evidence of incomplete relaxation in the reaction Ag+40Ar at 288 and 340 MeV bombarding energies

International Nuclear Information System (INIS)

Galin, J.; Moretto, L.G.; Babinet, R.; Schmitt, R.; Jared, R.; Thompson, S.G.

1975-01-01

The particles emitted in the reaction induced by 40 Ar on natural Ag at 288 and 340 MeV bombarding energy have been studied. The fragments have been identified in atomic number, their kinetic energy distribution and their angular distributions have been measured. The kinetic energy spectra show two components: a high-energy component related to the beam energy, or quasi-elastic component, and a low kinetic energy component, close to the Coulomb energy called relaxed component. The relaxed component is present at all angles and for all particles. The quasi-elastic component is present close to the grazing angle for atomic numbers close to that of the projectile. The relaxed cross section increases with atomic number for Z>9. The increase in cross section is sharper for the lower bombarding energy. The angular distributions are forward peaked, in excess of 1/sin(theta) for all the measured atomic numbers. The forward peaking is larger for particles close in Z to the projectile. The results are interpreted in terms of characteristic times associated with a short-lived intermediate complex. The cross sections and angular distributions are satisfactorily reproduced on the basis of a model accounting for a diffusion process occurring along the mass asymmetry coordinate of the intermediate complex. (Auth.)

Ejection of fast recoil atoms from solids under ion bombardment (medium-energy ion scattering by solid surfaces: Pt. 3)

International Nuclear Information System (INIS)

Dodonoy, A.I.; Mashkova, E.S.; Molchanov, V.A.

1989-01-01

This paper is the third part of our review surface scattering. Part I, which was devoted to the scattering of ions by the surfaces of disordered solids, was published in 1972; Part II, concerning scattering by crystal surfaces, was published in 1974. Since the publication of these reviews the material contained in them has become obsolete in many respects. A more recent account of the status of the problem has been given in a number of studies, including the book by E.S. Mashkova and V.A. Molchanov, Medium-Energy Ion Scattering by Solid Surfaces (Atomizdat, Moscow, 1980), than extended version of which was published by North-Holland in 1985. We note, however, that at the time these reviews were written the study of fast recoil atoms had not been carried out systematically; the problem was studied only as a by-product of surface scattering and sputtering. For this reason, in the above-mentioned works and in other reviews the data relating to recoil atoms were considered only occasionally. In recent years there have appeared a number of works - theoretical, experimental and computer -specially devoted to the study of the ejection of recoil atoms under ion bombardment. A number of interesting effects, which are due to the crystal structure of the target, have been discovered. It therefore, appeared desirable to us to systematize the available material and to present it as Part III of our continuing review. (author)

Electrorheological Properties of Suspensions Prepared from Polystyrene- Block- Polyisoprene Copolymer

OpenAIRE

YAVUZ, Mustafa

2014-01-01

Considerable scientific and industrial interest is currently being focused on a class of materials known as electrorheological (ER) fluids, which display remarkable rheological behaviour, being able to convert rapidly and repeatedly from a liquid to solid when an electric field (E) is applied or removed. In this article, the synthesis, characterization, partial hydrolysis and ER properties of polystyrene- block}-polyisoprene copolymer (COP) were investigated. The block copolymer was ...

Angular dependence of secondary ion emission from silicon bombarded with inert gas ions

International Nuclear Information System (INIS)

Wittmaack, K.

1984-01-01

The emission of positive and negative, atomic and molecular secondary ions sputtered from silicon has been studied under ultrahigh vacuum conditions. The sample was bombarded with 2-12 keV Ar + and Xe + ions at angles of incidence between 0 0 and 60 0 to the surface normal. The angular dependence of the secondary ion intensity as well as the energy spectra of Si + and Si - were found to differ significantly. The effect is attributed mostly do differences in the rate of neutralization. The stability of molecular ions appears to be independent of the charge state. Supporting evidence is provided for the idea that multiply charged secondary ions are due to Auger de-excitation of sputtered atoms in vacuum. (orig.)

Auger emission from solid surfaces bombarded with ions

International Nuclear Information System (INIS)

Grizzi, Oscar.

1986-01-01

The Auger electron emission from Be, Na, Mg, Al and Si bombarded with 0,5-20 KeV noble gas ions is studied. Sharp structures of the Auger electron spectra of Na and Be were identified. A Monte Carlo program was adapted to simulate the colision cascade in the solid, inner shell excitations and Auger decays. From the comparision of experimental and simulated Auger intensities, the relative role of symmetric and asymmetric collisions in Be K- and Al L-shell excitation were evaluated. In the case of Be, the discussion of the exciting processes to higher projectile energies was extended. To this end, the simulation to early measurements of Be K X-ray yields was applied. From this analysis, information about the variations of the fluorescence yield and outer-shell occupation numbers of Be with projectile energy was obtained. The study of the shape of the sharp Auger structures and their dependence with the energy and incidence projectile angle gives information about the collisional processes, inner hole lifetimes and Auger decays. From the evaluation of the energy and angular distribution of the excited sputtered atoms and the interaction between them and the metallic-surface, the energy shift distributions in the Auger energies were obtained. From the comparison of these distributions with the experimental atomic peaks, the main causes of the broadening of these peaks were determined. (M.E.L.) [es

Influence of ion bombardment on microcrystalline silicon material quality and solar cell performances

OpenAIRE

Bugnon, G; Feltrin, A; Sculati-Meillaud, F; Bailat, J; Ballif, C

2008-01-01

Microcrystalline hydrogenated silicon growth with VHF-PECVD was examined in an industrial type parallel plate KAITM reactor. The influence of pressure on material quality was studied in single junction solar cells. Solar cells with their intrinsic layer prepared at higher pressures exhibit remarkable improvements, reaching 8.2% efficiency at 3.5 mbar. Further analyzes showed that μc- Si:H intrinsic layers grown at higher pressures have a significantly lower defect density. These results are a...

Metallic vapor supplying by the electron bombardment for a metallic ion production with an ECR ion source

Energy Technology Data Exchange (ETDEWEB)

Kitagawa, Atsushi; Sasaki, Makoto; Muramatsu, Masayuki [National Inst. of Radiological Sciences, Chiba (Japan); Jincho, Kaoru; Sasaki, Noriyuki; Sakuma, Tetsuya; Takasugi, Wataru; Yamamoto, Mitsugu [Accelerator Engineering Corporation, Chiba (Japan)

2001-11-19

To produce the metallic ion beam for the injection into the Heavy Ion Medical Accelerator in Chiba (HIMAC) at the National Institute of Radiological Sciences (NIRS), a new gas supply method has been developed for an 18 GHz ECR ion source (NIRS-HEC). A metallic target rod at a high positive potential is melted by the electron bombardment technique. The evaporated gas with a maximum flow rate of 50A/sec is supplied into the ECR plasma in case of Fe metal. (author)

Metallic vapor supplying by the electron bombardment for a metallic ion production with an ECR ion source

International Nuclear Information System (INIS)

Kitagawa, Atsushi; Sasaki, Makoto; Muramatsu, Masayuki; Jincho, Kaoru; Sasaki, Noriyuki; Sakuma, Tetsuya; Takasugi, Wataru; Yamamoto, Mitsugu

2001-01-01

To produce the metallic ion beam for the injection into the Heavy Ion Medical Accelerator in Chiba (HIMAC) at the National Institute of Radiological Sciences (NIRS), a new gas supply method has been developed for an 18 GHz ECR ion source (NIRS-HEC). A metallic target rod at a high positive potential is melted by the electron bombardment technique. The evaporated gas with a maximum flow rate of 50A/sec is supplied into the ECR plasma in case of Fe metal. (author)

Surface etching mechanism of carbon-doped Ge{sub 2}Sb{sub 2}Te{sub 5} phase change material in fluorocarbon plasma

Energy Technology Data Exchange (ETDEWEB)

Shen, Lanlan [Chinese Academy of Sciences, State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Micro-system and Information Technology, Shanghai (China); Graduate School of the Chinese Academy of Sciences, Beijing (China); Song, Sannian; Song, Zhitang; Li, Le; Guo, Tianqi; Cheng, Yan; Lv, Shilong; Wu, Liangcai; Liu, Bo; Feng, Songlin [Chinese Academy of Sciences, State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Micro-system and Information Technology, Shanghai (China)

2016-09-15

Recently, carbon-doped Ge2Sb2Te5 (CGST) phase change material has been widely researched for being highly promising material for future phase change memory application. In this paper, the reactive-ion etching of CGST film in CF{sub 4}/Ar plasma is studied. Compared with GST, the etch rate of CGST is relatively lower due to the existence of carbon which reduce the concentration of F or CF{sub x} reactive radicals. It was found that Argon plays an important role in defining the sidewall edge acuity. Compared with GST, more physical bombardment is required to obtain vertical sidewall of CGST. The effect of fluorocarbon gas on the damage of the etched CGST film was also investigated. A Ge- and Sb-deficient layer with tens of nanometers was observed by TEM combining with XPS analysis. The reaction between fluorocarbon plasma and CGST is mainly dominated by the diffusion and consumption of reactive fluorine radicals through the fluorocarbon layer into the CGST substrate material. The formation of damage layer is mainly caused by strong chemical reactivity, low volatility of reaction compounds and weak ion bombardment. (orig.)

Measuring Gene Expression in Bombarded Barley Aleurone Layers with Increased Throughput.

Science.gov (United States)

Uwase, Grace; Enrico, Taylor P; Chelimo, David S; Keyser, Benjamin R; Johnson, Russell R

2018-03-30

The aleurone layer of barley grains is an important model system for hormone-regulated gene expression in plants. In aleurone cells, genes required for germination or early seedling development are activated by gibberellin (GA), while genes associated with stress responses are activated by abscisic acid (ABA). The mechanisms of GA and ABA signaling can be interrogated by introducing reporter gene constructs into aleurone cells via particle bombardment, with the resulting transient expression measured using enzyme assays. An improved protocol is reported that partially automates and streamlines the grain homogenization step and the enzyme assays, allowing significantly more throughput than existing methods. Homogenization of the grain samples is carried out using an automated tissue homogenizer, and GUS (β-glucuronidase) assays are carried out using a 96-well plate system. Representative results using the protocol suggest that phospholipase D activity may play an important role in the activation of HVA1 gene expression by ABA, through the transcription factor TaABF1.

Topography development on selected inert gas and self-ion bombarded Si

International Nuclear Information System (INIS)

Vishnyakov, V.; Carter, G.; Goddard, D.T.; Nobes, M.J.

1995-01-01

An AFM and SEM study of the topography induced by 20 keV Si + , Ar + and Xe + ion bombardment of Si at 45 o incidence angles and for ion fluences between 10 17 and 10 20 cm -2 has been undertaken at room temperature. All species generate an atomic scale random roughness, the magnitude of which does not increase extensively with ion fluence, suggesting the operation of a local relaxation process. This nanometre scale roughness forms, for Ar and Xe, a background for coarser micrometre scale structures such as pits, chevrons and waves. Apart from isolated etch pits Si + irradiation generates no repetitive micrometre scale structures. Xe + irradiation produces well developed transverse waves while Ar + irradiation results in isolated chevron-like etch pit trains and ripple patches. This latter pattern evolves, with increasing ion fluence, to a corrugated facet structure. The reasons for the different behaviours are still not fully clarified. (author)

A Study on Planning Strategies for Urban Housing Block Development

Institute of Scientific and Technical Information of China (English)

Zeng Wei; Wang Hua; You Juanjuan; Wang Linlin; Li Caige

2016-01-01

As a city is the carrier of human society and housing is an important part of a citizen's life and survival,the citizens' choice of their housing mode will influence the material and spiritual life of the individuals,families,and society.In view of the diversification of values and investments,people are eager for a harmonious relationship between the community and the city.As a kind of compact and efficient housing mode,the housing block highlights the organic link of the community within the city in an open and shared living environment.This paper reviews the development of housing blocks in various countries and summarizes the characteristics of housing blocks through a comparison with traditional gated residential quarters and urban blocks.It then analyzes the current difficulties of housing block development in China from aspects such as the planning concept,planning system,management mode,and development mode and accordingly proposes planning principles and strategies in hope of providing theoretical supports for the development and construction of housing blocks in China.

Discoloration of various CAD/CAM blocks after immersion in coffee

Directory of Open Access Journals (Sweden)

Sasipin Lauvahutanon

2017-02-01

Full Text Available Objectives This study evaluated color differences (ΔEs and translucency parameter changes (ΔTPs of various computer-aided design/computer-aided manufacturing (CAD/CAM blocks after immersion in coffee. Materials and Methods Eight CAD/CAM blocks and four restorative composite resins were evaluated. The CIE L*a*b* values of 2.0 mm thick disk-shaped specimens were measured using the spectrophotometer on white and black backgrounds (n = 6. The ΔEs and ΔTPs of one day, one week, and one month immersion in coffee or water were calculated. The values of each material were analyzed by two-way ANOVA and Tukey's multiple comparisons (α = 0.05. The ΔEs after prophylaxis paste polishing of 1 month coffee immersion specimens, water sorption and solubility were also evaluated. Results After one month in coffee, ΔEs of CAD/CAM composite resin blocks and restorative composites ranged from 1.6 to 3.7 and from 2.1 to 7.9, respectively, and ΔTPs decreased. The ANOVA of ΔEs and ΔTPs revealed significant differences in two main factors, immersion periods and media, and their interaction except for ΔEs of TEL (Telio CAD, Ivoclar Vivadent. The ΔEs significantly decreased after prophylaxis polishing except GRA (Gradia Block, GC. There was no significant correlation between ΔEs and water sorption or solubility in water. Conclusions The ΔEs of CAD/CAM blocks after immersion in coffee varied among products and were comparable to those of restorative composite resins. The discoloration of CAD/CAM composite resin blocks could be effectively removed with prophylaxis paste polishing, while that of some restorative composites could not be removed.

Study of the reuse of construction residues in concrete employed by blocks manufacture

Directory of Open Access Journals (Sweden)

R. C. C. Lintz

Full Text Available The use of construction and demolition waste (CDR comes as an alternative for recycling, for costs reduction and for raw material. The CONAMA Resolution 307 (National Council for the Environment establishes that all cities should find an environmentally correct destination to CDR. In this research the mechanical properties of the concrete containing CDR were analyzed aiming its use in the production of concrete blocks. Here, increasing percentages of aggregates of CDR with the same granulometry an substitute the natural aggregate, and then concrete blocks were molded. Tests were then performed in order to determine the compression strength according to NBR 12118:2007, at ages of 14 days and 28 days. It was noticed that the values resulting from the compression strength test were also influenced by the increasing substitution of CDR percentages to the mixture. This research discusses the great potential of using this material in substitution to the natural aggregates used in the production of concrete based materials such as blocks.

Production of Mg and Al Auger electrons by noble gas ion bombardment of Mg and Al surfaces. [3 KeV, electron promotion

Energy Technology Data Exchange (ETDEWEB)

Ferrante, J; Pepper, S V [National Aeronautics and Space Administration, Cleveland, Ohio (USA). Lewis Research Center

1976-08-01

In this letter the relative production efficiency of Mg and Al Auger electrons by He, Ne, Ar, Kr and Xe ion bombardment as a function of ion energy (<=3 keV) is reported. Some comments on the interpretation of the results in terms of electron promotion are also given.

Poly(ferrocenylsilane)-block-Polylactide Block Copolymers

NARCIS (Netherlands)

Roerdink, M.; van Zanten, Thomas S.; Hempenius, Mark A.; Zhong, Zhiyuan; Feijen, Jan; Vancso, Gyula J.

2007-01-01

A PFS/PLA block copolymer was studied to probe the effect of strong surface interactions on pattern formation in PFS block copolymer thin films. Successful synthesis of PFS-b-PLA was demonstrated. Thin films of these polymers show phase separation to form PFS microdomains in a PLA matrix, and

Two-Dimensional Liquid Chromatography Analysis of Polystyrene/Polybutadiene Block Copolymers.

Science.gov (United States)

Lee, Sanghoon; Choi, Heejae; Chang, Taihyun; Staal, Bastiaan

2018-05-15

A detailed characterization of a commercial polystyrene/polybutadiene block copolymer material (Styrolux) was carried out using two-dimensional liquid chromatography (2D-LC). The Styrolux is prepared by statistical linking reaction of two different polystyrene- block-polybutadienyl anion precursors with a multivalent linking agent. Therefore, it is a mixture of a number of branched block copolymers different in molecular weight, composition, and chain architecture. While individual LC analysis, including size exclusion chromatography, interaction chromatography, or liquid chromatography at critical condition, is not good enough to resolve all the polymer species, 2D-LC separations coupling two chromatography methods were able to resolve all polymer species present in the sample; at least 13 block copolymer species and a homopolystyrene blended. Four different 2D-LC analyses combining a different pair of two LC methods provide their characteristic separation results. The separation characteristics of the 2D-LC separations are compared to elucidate the elution characteristics of the block copolymer species.

Improved cladding nano-structured materials with self-repairing capabilities

International Nuclear Information System (INIS)

Popa-Simil, L.

2012-01-01

When designing nuclear reactors or the materials that go into them, one of the key challenges is finding materials that can withstand an outrageously extreme environment. In addition to constant bombardment by radiation, reactor materials may be subjected to extremes in temperature, physical stress, and corrosive conditions. A limitation in fuel burnup is and usage of the nuclear fuel material is related to the structural material radiation damage, that makes the fuel be removed with low-burnup and immobilized in the waste storage pools. The advanced burnup brings cladding material embitterment due to radiation damage effects corroborated with corrosion effects makes the fuel pellet life shorter. The novel nano-clustered structured sintered material may mitigate simultaneously the radiation damage and corrosion effects driving to more robust structural materials that may make the nuclear reactor safer and more reliable. The development of nano-clustered sinter alloys provides new avenues for further examination of the role of grain boundaries and engineered material interfaces in self-healing of radiation-induced defects driving to the design of highly radiation-tolerant materials for the next generation of nuclear energy applications. (authors)

Orientation: Automotive Mechanics Instructional Program. Block 1.

Science.gov (United States)

O'Brien, Ralph D.

The first six instructional blocks in automotive mechanics, the lessons and supportive information in the document provide a guide for teachers in planning an instructional program in the basic theory and practice of a beginning course at the secondary and post-secondary level. The material, as organized, is a suggested sequence of instruction…

Block copolymer micelles as switchable templates for nanofabrication.

Science.gov (United States)

Krishnamoorthy, Sivashankar; Pugin, Raphaël; Brugger, Juergen; Heinzelmann, Harry; Hoogerwerf, Arno C; Hinderling, Christian

2006-04-11

Block copolymer inverse micelles from polystyrene-block-poly-2-vinylpyridine (PS-b-P2VP) deposited as monolayer films onto surfaces show responsive behavior and are reversibly switchable between two states of different topography and surface chemistry. The as-coated films are in the form of arrays of nanoscale bumps, which can be transformed into arrays of nanoscale holes by switching through exposure to methanol. The use of these micellar films to act as switchable etch masks for the structuring of the underlying material to form either pillars or holes depending on the switching state is demonstrated.

Materials behaviour in PWRs core

International Nuclear Information System (INIS)

Barbu, A.; Massoud, J.P.

2008-01-01

Like in any industrial facility, the materials of PWR reactors are submitted to mechanical, thermal or chemical stresses during particularly long durations of operation: 40 years, and even 60 years. Materials closer to the nuclear fuel are submitted to intense bombardment of particles (mainly neutrons) coming from the nuclear reactions inside the core. In such conditions, the damages can be numerous and various: irradiation aging, thermal aging, friction wear, generalized corrosion, stress corrosion etc.. The understanding of the materials behaviour inside the cores of reactors in operation is a major concern for the nuclear industry and its long term forecast is a necessity. This article describes the main ways of materials degradation without and under irradiation, with the means used to foresee their behaviour using physics-based models. Content: 1 - structures, components and materials: structure materials, nuclear materials; 2 - main ways of degradation without irradiation: thermal aging, stress corrosion, wear; 3 - main ways of degradation under irradiation: microscopic damaging - point defects, dimensional alterations, evolution of mechanical characteristics under irradiation, irradiation-assisted stress corrosion cracking (IASCC), synergies; 4 - forecast of materials evolution under irradiation using physics-based models: primary damage - fast dynamics, primary damage annealing - slow kinetics microstructural evolution, impact of microstructural changes on the macroscopic behaviour, insight on modeling methods; 5 - materials change characterization techniques: microscopic techniques - direct defects observation, nuclear techniques using a particle beam, global measurements, mechanical characterizations; 6 - perspectives. (J.S.)

The use of fiy ash in concrete blocks

Directory of Open Access Journals (Sweden)

Álvarez Alonso, Marina

1991-12-01

Full Text Available This paper describes how fly ashes which are not prescribed by the standards can be used in the manufacturing of concrete blocks. To implement this proposal it was necessary to do tests of the constitutive materials of the blocks, and block tests. The objective of these tests is to obtain the optimum blocks. This paper presents these tests and its main results.

Se describe la posible utilización de cenizas volantes consideradas no aptas como sustituto del cemento por la normativa, que pueden ser utilizadas en otros sectores de la industria de la construcción como la de prefabricación de piezas de hormigón. Para ello, ha sido necesario realizar ensayos sobre los materiales constituyentes de los bloques así como de los propios bloques con el fin de obtener cuál es el elemento de hormigón más idóneo. En este artículo se presentan estos ensayos así como los principales resultados obtenidos.

Block and sub-block boundary strengthening in lath martensite

NARCIS (Netherlands)

Du, C.; Hoefnagels, J.P.M.; Vaes, R.; Geers, M.G.D.

2016-01-01

Well-defined uniaxial micro-tensile tests were performed on lath martensite single block specimens and multi-block specimens with different number of block boundaries parallel to the loading direction. Detailed slip trace analyses consistently revealed that in the {110}<111> slip system with the

On the Eigenvalues and Eigenvectors of Block Triangular Preconditioned Block Matrices

KAUST Repository

Pestana, Jennifer

2014-01-01

Block lower triangular matrices and block upper triangular matrices are popular preconditioners for 2×2 block matrices. In this note we show that a block lower triangular preconditioner gives the same spectrum as a block upper triangular preconditioner and that the eigenvectors of the two preconditioned matrices are related. © 2014 Society for Industrial and Applied Mathematics.

Powder wastes confinement block and manufacturing process of this block

International Nuclear Information System (INIS)

Dagot, L.; Brunel, G.

1996-01-01

This invention concerns a powder wastes containment block and a manufacturing process of this block. In this block, the waste powder is encapsulated in a thermo hardening polymer as for example an epoxy resin, the encapsulated resin being spread into cement. This block can contain between 45 and 55% in mass of wastes, between 18 and 36% in mass of polymer and between 14 and 32% in mass of cement. Such a containment block can be used for the radioactive wastes storage. (O.M.). 4 refs

M-subshell ionization of U by light-ion bombardment

International Nuclear Information System (INIS)

Jesus, A.P.; Ribeiro, J.P.

1988-01-01

M X-rays of U were produced by proton, deuteron and alpha-particle bombardment in the energy range of 0.20-1.00 MeV/u. N 6.7 →M 5 ((M subα)),N 6 →M 4 (M β ), N 5 →M 3 (M γ ), N 4 →M 2 and N 2 →M 1 line yields were obtained from a least-squares fit to the spectra and used to convert M X-ray production into M-subshell ionization cross sections. The uncertainty induced by the atomic parameters (X-ray fluorescence yields, Coster-Kronig and radiative transition rates) used in the conversion is discussed. The subshell ionization cross sections are then compared to PWBA values corrected for Coulomb deflection and energy loss according to Brandt and Lapicki, to the semiclassical theoretical values of Kocbach and to relativistic PWBA results, corrected for Coulomb and binding effects, of Chen et al. Intrashell transitions induced by the projectile and multiple ionization are suggested as causes of disagreement between theory and experiment, especially for alpha-particles. It is concluded that theory must go beyond the simple picture of the first-order pertubation approximation to explain M-subshell results and the care must be taken in the choice of wave functions. (author) [pt

Blocked Randomization with Randomly Selected Block Sizes

Directory of Open Access Journals (Sweden)

Jimmy Efird

2010-12-01

Full Text Available When planning a randomized clinical trial, careful consideration must be given to how participants are selected for various arms of a study. Selection and accidental bias may occur when participants are not assigned to study groups with equal probability. A simple random allocation scheme is a process by which each participant has equal likelihood of being assigned to treatment versus referent groups. However, by chance an unequal number of individuals may be assigned to each arm of the study and thus decrease the power to detect statistically significant differences between groups. Block randomization is a commonly used technique in clinical trial design to reduce bias and achieve balance in the allocation of participants to treatment arms, especially when the sample size is small. This method increases the probability that each arm will contain an equal number of individuals by sequencing participant assignments by block. Yet still, the allocation process may be predictable, for example, when the investigator is not blind and the block size is fixed. This paper provides an overview of blocked randomization and illustrates how to avoid selection bias by using random block sizes.

Structure carbon materials: clusters, nanotubes, ion-implant polymers and diamonds

International Nuclear Information System (INIS)

Lapchuk, N.M.; Odzhaev, V.B.; Poklonskij, N.A.; Sviridov, D.V.

2009-01-01

The paper summarizes the series of research works dealing with the physics of nanostructured carbon materials, which were awarded a Sevchenko Prize in 2008. The paper considers the mechanism of synthesis of 3D carbon nanospecies and their nanomechanics, magnetic properties of ion-implanted diamonds, as well as the regularities of formation of novel forms of amorphous hydrogenated carbon and metal-carbon nanocomposites via ion bombardment of polymers, as well as electronic, magnetic, and structural properties of ion-implanted polymers an their possible applications in micro- and nanoelectronics. (authors)

Study of clean and ion bombardment damaged silver single crystal surfaces by work function measurements

International Nuclear Information System (INIS)

Chelvayohan, N.

1982-06-01

Work function values of the (110), (100) and (111) faces of silver single crystal were measured by the photoelectric emission method and found to be 4.14 +- 0.04 eV, 4.22 +-0.04 eV and 4.46 +- 0.02 eV respectively. Oxygen adsorption on the faces were studied by surface potential measurement. Strong oxygen adsorption was observed on (110) and (100) faces, whereas the (111) face was found to be inert for oxygen adsorption. Oxygen adsorption on the (111) face damaged by argon ion bombardment was also investigated. The above results were compared with those of early reported work function and oxygen adsorption values. (U.K.)

Life cycle cost of different Walling material used for affordable housing in tropics

Directory of Open Access Journals (Sweden)

Chameera Udawattha

2017-12-01

The results show that mud concrete block is the most suitable walling material. The brick has the highest account for the embedded energy. The hollow cement block is the worse building materials in tropics and its carbon footprint is comparatively higher. Even though the brick has higher embedded energy and construction cost, in a long run brick is less expensive than hollow cement block and Cabook walling material. Concluding, mud concrete block is comparatively most sustainable walling material for building affordable housing in tropics.