WorldWideScience

Sample records for mass production test

  1. Mass production test of Hamamatsu MPPC for T2K neutrino oscillation experiment

    CERN Document Server

    Yokoyama, M; Gomi, S; Minamino, A; Nagai, N; Nitta, K; Orme, D; Otani, M; Murakami, T; Nakadaira, T; Tanaka, M

    2008-01-01

    In the T2K near neutrino detectors, about 60 000 Hamamatsu Multi-Pixel Photon Counters (MPPCs) will be used. The mass production of MPPC has started in February 2008.In order to perform quality assurance and to characterize each device, we have developed an MPPC test system. For each MPPC, gain, breakdown voltage, noise rate, photo detection efficiency, and cross-talk and after-pulse rate are measured as functions of the bias voltage and temperature. The design of the test system and the measurement procedure are described.

  2. TECHNOLOGICAL TESTS USING QUARTZITE RESIDUES AS COMPONENT OF CERAMIC MASS AT THE PORCELAIN STONEWARE PRODUCTION

    Directory of Open Access Journals (Sweden)

    Marcondes Mendes Souza

    2015-03-01

    Full Text Available This work aims to evaluate through technological tests the use of quartzite residues as component at the the production of porcelain stoneware. Were collected five samples of quartzites called of green quartzite, black quartzite, pink quartzite, goldy quartzite, white quartzite. After, the raw materials were milled, passed by a sieve with a Mesh of 200# (Mesh and characterized by chemical analysis in fluorescence of x-rays and also analysis of the crystalline phases by diffraction of x-rays. The porcelain tiles mass is composed of five formulations containing 57% of feldspar, 37% of clay and 6% of residues of quartzite with different coloration. For the preparation of the specimens, it was used uniaxial pressing, which afterwards were synthesized at 1150°C, 1200°C and 1250°C. After the sintering, the specimens were submit for tests of technological characterization like: water absorption, linear shrinkage, apparently porosity, density and flexural strain at three points. The results presented in the fluorescence of x-rays showed a high-content of iron oxide on black quartzite that is why it was discarded the utilization of it in porcelain stoneware. All quartzite formulations had low water absorption achieved when synthesized at 1200°C, getting 0.1 to 0.36% without having gone through the atomization process. At the tests of flexural strain, all the quartzite had in acceptance limits, according to the European norm EN 100, overcoming 27 MPA at 1200°C

  3. PID Testing Method Suitable for Process Control of Solar Cells Mass Production

    Directory of Open Access Journals (Sweden)

    Xianfang Gou

    2015-01-01

    Full Text Available Voltage bias of several hundred volts which are applied between solar cells and module frames may lead to significant power losses, so-called potential-induced degradation (PID, in normal photovoltaic (PV installations system. Modules and minimodules are used to conduct PID test of solar cells. The test procedure is time consuming and of high cost, which cannot be used as process monitoring method during solar cells fabrication. In this paper, three kinds of test including minimodule, Rsh, and V-Q test are conducted on solar cells or wafers with SiNx of different refractive index. All comparisons between test results of Rsh, V-Q, and minimodule tests have shown equal results. It is shown that Rsh test can be used as quality inspection of solar cells and V-Q test of coated wafer can be used as process control of solar cells.

  4. PID Testing Method Suitable for Process Control of Solar Cells Mass Production

    OpenAIRE

    Xianfang Gou; Xiaoyan Li; Su Zhou; Shaoliang Wang; Weitao Fan; Qingsong Huang

    2015-01-01

    Voltage bias of several hundred volts which are applied between solar cells and module frames may lead to significant power losses, so-called potential-induced degradation (PID), in normal photovoltaic (PV) installations system. Modules and minimodules are used to conduct PID test of solar cells. The test procedure is time consuming and of high cost, which cannot be used as process monitoring method during solar cells fabrication. In this paper, three kinds of test including minimodule, Rsh, ...

  5. Standardization of automated industrial test equipment for mass production of control systems

    CERN Document Server

    AUTHOR|(CDS)2090663; Dai, Iosifina Panagiota; Oleniuk, Patryk Wojciech; Todd, Benjamin

    2016-01-01

    Power converters and their controls electronics are key elements for the operation of the CERN accelerator complex, having a direct impact on its availability. They must be designed to achieve a high Mean Time Between Failure (MTBF) and hardware reliability must be ensured by board level testing before hardware is assembled and installed. In this framework, the National Instrument PCI extension for Instrumentation (PXI) was chosen as standard platform for the development of testers. This paper reports on the design strategy and approach used focusing on the tester hardware, firmware and software development.

  6. MASS CUSTOMIZATION and PRODUCT MODELS

    DEFF Research Database (Denmark)

    Svensson, Carsten; Malis, Martin

    2003-01-01

    to the product. Through the application of a mass customization strategy, companies have a unique opportunity to create increased customer satisfaction. In a customized production, knowledge and information have to be easily accessible since every product is a unique combination of information. If the dream...... of a customized alternative instead of a uniform mass-produced product shall become a reality, then the cross-organizational efficiency must be kept at a competitive level. This is the real challenge for mass customization. A radical restructuring of both the internal and the external knowledge management systems...

  7. MASS CUSTOMIZATION and PRODUCT MODELS

    DEFF Research Database (Denmark)

    Svensson, Carsten; Malis, Martin

    2003-01-01

    to the product. Through the application of a mass customization strategy, companies have a unique opportunity to create increased customer satisfaction. In a customized production, knowledge and information have to be easily accessible since every product is a unique combination of information. If the dream...... of a customized alternative instead of a uniform mass-produced product shall become a reality, then the cross-organizational efficiency must be kept at a competitive level. This is the real challenge for mass customization. A radical restructuring of both the internal and the external knowledge management systems......When dealing with complex product models, efficient knowledge distribution is essential to obtain success. This paper describes how product models can be applied to support the knowledge distribution. The change towards individualization will radically affect the knowledge application in relation...

  8. Triple Pulsar Tests Mass Triplets

    CERN Document Server

    Shao, Lijing

    2016-01-01

    Three conceptually different masses appear in equations of motion for objects under gravity, namely, inertial mass, $m_{\\cal I}$, passive gravitational mass, $m_{\\cal P}$, and active gravitational mass, $m_{\\cal A}$. It is assumed that, for any objects, $m_{\\cal I} = m_{\\cal P} = m_{\\cal A}$ in Newtonian gravity, and $m_{\\cal I} = m_{\\cal P}$ in Einsteinian gravity, oblivious to objects' sophisticated internal structure. Empirical examination of the equivalence probes deep into gravity theories. We propose new tests based on pulsar timing of the stellar triple system, PSR J0337+1715. Various machine-precision three-body simulations are performed, from which, equivalence-violating parameters are extracted with Markov chain Monte Carlo sampling that takes full correlations into account. We show that the difference in masses can be probed to $3\\times10^{-8}$, improving the post-Newtonian constraints of strong equivalence principle by $10^3$--$10^6$. The test of $m_{\\cal P}=m_{\\cal A}$ presents the first test of ...

  9. Mass production of entomopathogenic hypocreales

    Science.gov (United States)

    The Hypocreales, Beauveria bassiana, Metarhizium anisopliae sensu lato, Isaria fumosorosea and I. farinosus, and Nomuraea rileyi, have become important insect control agents in recent times and consequently subjects of much scientific study and development. Mass production of infective stages is imp...

  10. Testing the limits in a greenhouse ocean: Did low nitrogen availability limit marine productivity during the end-Triassic mass extinction?

    Science.gov (United States)

    Schoepfer, Shane D.; Algeo, Thomas J.; Ward, Peter D.; Williford, Kenneth H.; Haggart, James W.

    2016-10-01

    The end-Triassic mass extinction has been characterized as a 'greenhouse extinction', related to rapid atmospheric warming and associated changes in ocean circulation and oxygenation. The response of the marine nitrogen cycle to these oceanographic changes, and the extent to which mass extinction intervals represent a deviation in nitrogen cycling from other ice-free 'greenhouse' periods of Earth history, remain poorly understood. The well-studied Kennecott Point section in Haida Gwaii, British Columbia, Canada, was deposited in the open Panthalassic Ocean, and is used here as a test case to better understand changes in the nitrogen cycle and marine productivity from the pre-crisis greenhouse of the Rhaetian to the latest-Rhaetian crisis interval. We estimated marine productivity from the late Norian to the early Hettangian using TOC- and P-based paleoproductivity transform equations, and then compared these estimates to records of sedimentary nitrogen isotopes, redox-sensitive trace elements, and biomarker data. Major negative excursions in δ15N (to ≤ 0 ‰) correspond to periods of depressed marine productivity. During these episodes, the development of a stable pycnocline below the base of the photic zone suppressed vertical mixing and limited N availability in surface waters, leading to low productivity and increased nitrogen fixation, as well as ecological stresses in the photic zone. The subsequent shoaling of euxinic waters into the ocean surface layer was fatal for most Triassic marine fauna, although the introduction of regenerated NH4+ into the photic zone may have allowed phytoplankton productivity to recover. These results indicate that the open-ocean nitrogen cycle was influenced by climatic changes during the latest Triassic, despite having existed in a greenhouse state for over 50 million years previously, and that low N availability limited marine productivity for hundreds of thousands of years during the end-Triassic crisis.

  11. Innovations in Mechatronic Products and Mass Customization

    DEFF Research Database (Denmark)

    Habib, Tufail; Jørgensen, Kaj Asbjørn; Nielsen, Kjeld

    2011-01-01

    Mass Customization (MC) has been recognized as a successful strategy in the design and development of products tailored to customer needs. Global competition demands new products with added functionalities, as in the case of mechatronic products. These products are becoming more and more important...... as a product type and new inventions have resulted in drastic changes in design and development of mechatronic products. Conventional mechanical systems are enhanced by mechatronic systems. In this paper, the particular structure and properties of mechatronic products compared to conventional mechanical...... systems is presented. The successful strategy of mass customization has contributed to innovations in the development of mechatronic products and the paper presents an overview of typical changes regarding functionalities from mechanical products towards mechatronic products....

  12. Fission product separations testing

    Energy Technology Data Exchange (ETDEWEB)

    Bostick, D.A.; DePaoli, S.M. [Oak Ridge National Lab., TN (United States)

    1997-10-01

    The initial goal of this task is to adequately understand the treatment needs of the end user in treating contaminated wastewater. These needs are then incorporated into the evaluation of new treatment technologies for wastewater treatment. Pertinent information is than supplied to the end user so that they can select a preferred process to meet their waste treatment needs. New sorbent materials, ion-exchange materials, or other processes of interest to DOE`s Office of Environmental Restoration (EM-40) will be evaluated initially for the removal of {sup 90}Sr and {sup 137}Cs from groundwater and process wastewater. Laboratory studies will strive to obtain a quantitative understanding of the behavior of these new materials and to evaluate their sorption efficiency in reference to a standard benchmark treatment technique. Testing of the new materials will begin by conducting scoping tests where new treatment materials are compared with standard, commercially available materials in batch shaker tests. Experimental data for the most promising sorbents will then be fit to an equilibrium model so that nuclide sorption can be predicted for variable wastewater composition. Additional testing with actual wastewater will be conducted with two or three of the most effective treatment methods. Once batch testing of a treatment method is completed, dynamic column tests will be performed to validate the equilibrium sorption model and to obtain the defining column operating parameters for scaling up the technology.

  13. Human sports drug testing by mass spectrometry.

    Science.gov (United States)

    Schänzer, Wilhelm; Thevis, Mario

    2017-01-01

    Since the installation of anti-doping rules and regulations and their international enforcement in the mid-1960s, mass spectrometry has been an integral part of doping control procedures. Although its utility was limited in the first decade, instrumental improvements and method optimizations have made mass spectrometry, in all its facets, an indispensable tool in modern sports drug testing. In this review, milestones in doping control analysis accomplished in Germany and reaching from the early developments to the current use of hyphenated mass spectrometric techniques concerning low- and high molecular mass analytes are presented. The considered drug classes include anabolic agents, peptidic drugs, nucleotide-derived therapeutics, approved and non-approved organic as well as inorganic analytes, and particular focus is put on drug class- and instrument-driven strategies. © 2015 Wiley Periodicals, Inc. Mass Spec Rev 36:16-46, 2017.

  14. REQUIREMENT PRODUCT CONFIGURATION IN MASS CUSTOMIZATION

    Institute of Scientific and Technical Information of China (English)

    Wang Xin; Tan Jianrong; Zhang Shuyou; Wu Peining

    2005-01-01

    On the basis of researching on requirement product configuration in mass customization, the concept of product family requirement class (PFRC) and requirement-matching template are put forward. A case-based requirement product configuration (CB-RPC) model and corresponding requirement product model are established. The result of requirement product configuration is obtained by using the method of two-level similar matching. In addition, the effect of the method on requirement responding is analyzed. Finally, the model and the method given are applied in elevator industry, and have improved the enterprise's ability of rapid responding to customer's requirements.

  15. Agility Evaluation of Mass Customization Product Manufacturing

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Mass Customization (MC) is one of the importance en te rprise produces modes in information age progressively. Mass Customization produ ct manufacturing is aimed at the objection of agile responding to customer deman d, market changing and market opportunities to combine with modern management te chnology and advanced manufacture technology, and to use the development model o f design for product family and technology concurrent. Therefore, in the environ ment of market continuing to change with a high spee...

  16. Carbon nanotube mass production: principles and processes.

    Science.gov (United States)

    Zhang, Qiang; Huang, Jia-Qi; Zhao, Meng-Qiang; Qian, Wei-Zhong; Wei, Fei

    2011-07-18

    Our society requires new materials for a sustainable future, and carbon nanotubes (CNTs) are among the most important advanced materials. This Review describes the state-of-the-art of CNT synthesis, with a focus on their mass-production in industry. At the nanoscale, the production of CNTs involves the self-assembly of carbon atoms into a one-dimensional tubular structure. We describe how this synthesis can be achieved on the macroscopic scale in processes akin to the continuous tonne-scale mass production of chemical products in the modern chemical industry. Our overview includes discussions on processing methods for high-purity CNTs, and the handling of heat and mass transfer problems. Manufacturing strategies for agglomerated and aligned single-/multiwalled CNTs are used as examples of the engineering science of CNT production, which includes an understanding of their growth mechanism, agglomeration mechanism, reactor design, and process intensification. We aim to provide guidelines for the production and commercialization of CNTs. Although CNTs can now be produced on the tonne scale, knowledge of the growth mechanism at the atomic scale, the relationship between CNT structure and application, and scale-up of the production of CNTs with specific chirality are still inadequate. A multidisciplinary approach is a prerequisite for the sustainable development of the CNT industry. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  17. Testing substellar models with dynamical mass measurements

    Directory of Open Access Journals (Sweden)

    Liu M.C.

    2011-07-01

    Full Text Available We have been using Keck laser guide star adaptive optics to monitor the orbits of ultracool binaries, providing dynamical masses at lower luminosities and temperatures than previously available and enabling strong tests of theoretical models. We have identified three specific problems with theory: (1 We find that model color–magnitude diagrams cannot be reliably used to infer masses as they do not accurately reproduce the colors of ultracool dwarfs of known mass. (2 Effective temperatures inferred from evolutionary model radii are typically inconsistent with temperatures derived from fitting atmospheric models to observed spectra by 100–300 K. (3 For the only known pair of field brown dwarfs with a precise mass (3% and age determination (≈25%, the measured luminosities are ~2–3× higher than predicted by model cooling rates (i.e., masses inferred from Lbol and age are 20–30% larger than measured. To make progress in understanding the observed discrepancies, more mass measurements spanning a wide range of luminosity, temperature, and age are needed, along with more accurate age determinations (e.g., via asteroseismology for primary stars with brown dwarf binary companions. Also, resolved optical and infrared spectroscopy are needed to measure lithium depletion and to characterize the atmospheres of binary components in order to better assess model deficiencies.

  18. Development and Evaluation of a Test System for the Quality Assurance during the Mass Production of Silicon Microstrip Detector Modules for the CMS Experiment

    CERN Document Server

    Franke, Torsten

    2005-01-01

    The Compact Muon Solenoid (CMS) is one of four large-scale experiments that is going to be installed at the Large Hadron Collider (LHC) at the European Laboratory for Particle Physics (CERN). For CMS an inner tracking system entirely equipped with silicon microstrip detectors was chosen. With an active area of about 198 m2 it will be the largest tracking device of the world that was ever constructed using silicon sensors. The basic components in the construction of the tracking system are approximately 16,000 so-called modules, which are pre-assembled units consisting of the sensors, the readout electronics and a support structure. The module production is carried out by a cooperation of number of institutes and industrial companies. To ensure the operation of the modules within the harsh radiation environment extensive tests have to be performed on all components. An important contribution to the quality assurance of the modules is made by a test system of which all components were developed in Aachen. In ad...

  19. Consumer oriented product noise testing

    Science.gov (United States)

    Blomberg, Les

    2005-09-01

    This paper explores the need for product noise measurements and how best to meet that need in the near future. Currently there is only a small market place for quieter consumer products. This is not because of lack of interest. No one really wants to announce to everyone in their house that they just flushed the toilet, few really want the entire neighborhood to know they are mowing their yard, etc. The small market place is primarily due to a lack of regulations on product noise, a lack of information easily available to consumers about which products are quieter, and market consolidation resulting in fewer manufacturers, most of whom are unwilling to emphasize their quieter products at the risk of eroding sales of their noisier ones (that currently have greater market share). In the absence of the EPA fulfilling its statutory requirement to regulate and label product noise under the Noise Control Act of 1972, and with the unwillingness of most industries to voluntarily publish accurate product noise data, there is a significant role for ``Consumer Oriented Product Noise Testing.'' This paper explores the Noise Pollution Clearinghouse's ongoing and planned product noise testing, evaluating its advantages, disadvantages, and limitations.

  20. RPC Production at General Tecnica: a mass scale production

    Science.gov (United States)

    della Volpe, D.; Morganti, S.

    2006-08-01

    The construction of LHC has deeply changed the RPC production. The enormous amount of detector needed and the strong requirements on gas volume quality had a deep impact on the production chain and on the QC and QA at the production site. This basically has brought the RPC from an almost hand-crafted detector to a medium scale mass product. The most critical aspects of the production chain have been modified and/or improved introducing new and more rigorous QC and QA procedures to guarantee the detector quality and improve the management of storage and the procurement on materials. Here it will be presented the work carried on in the last four year at the production site to improve and check the quality and the results achieved. Something like 10000 RPC were produced between 2002 and 2005. Also a preliminary and rough analysis on the efficiencies of the various phases in the chain production based on ATLAS production will be presented.

  1. Innovative Processes and Products for Mass Customization

    DEFF Research Database (Denmark)

    Blecker, Thorsten; Edwards, Kasper; Hvam, Lars

    simultaneously keeping costs and delivery times low following the approach of mass customization. But the majority of the SMEs with product platforms cannot afford to develop an individual product configurator. Therefore they have a large demand for a more cost-effective and flexible product configuration......This paper describes the solution developed in the KoViP project and presents the results of introducing this solution in the scope of a pilot project. The idea of the KoViP project targets SMEs of the German machine and plant manufacturing, which are forced to produce customized products whilst...... solution. The first part of the paper describes the product configuration software and service platform KoViP, developed by the CAD software provider ISD, Dortmund, in cooperation with the ITM chair of the University of Bochum and funded by the EU and the federal state of North Rhine-Westphalia. The main...

  2. Anaerobic Digestion: Mass Balances and Products

    DEFF Research Database (Denmark)

    Møller, Jacob; Christensen, Thomas Højlund; Jansen, Jes la Cour

    2011-01-01

    While the basic processes involved in anaerobic digestion of waste are described in Chapter 9.4 and the main digestion technologies are presented in Chapter 9.5, this chapter focuses on mass balances, gas production and energy aspects, environmental emissions and unit process inventories. Underst......While the basic processes involved in anaerobic digestion of waste are described in Chapter 9.4 and the main digestion technologies are presented in Chapter 9.5, this chapter focuses on mass balances, gas production and energy aspects, environmental emissions and unit process inventories....... Understanding these issues and being able to account for them is a prerequisite in digestion engineering and for establishing and running a successful anaerobic digestion facility. Of specific importance is the final use of the digestate. Use in agriculture as a fertilizer is described in Chapter 9.10 and use...

  3. Continuous squeeze casting process by mass production

    Institute of Scientific and Technical Information of China (English)

    Yun Xia; Rich Jacques

    2006-01-01

    Squeeze casting has become the most competitive casting process in the automotive industry because of its many advantages over high pressure die casting (HPDC). Many squeeze casting R & D and small amount volume making have been implemented around the world, but the mass production control still exists problem. SPX Contech squeeze casting process P2000 successfully achieved the goal of mass production; it includes lower metal turbulence, less gas entrapment, minimum volumetric shrinkage, and thus less porosity. Like other casting processes, however, the quality of squeeze castings is still sensitive to process control and gate and runner design. Casting defects can form in both die-filling and metal solidification phases. The occurrence of casting defects is directly attributed to improper adjustment or lack of control of process parameters including metal filling velocity, temperature, dwell time, cooling pattern, casting design, and etc. This paper presents examples using P2000 techniques to improve part quality in the following areas: runner & gate design, casting & runner layout in the die, squeeze pin application, high thermal conductivityinserts, cooling/heating systems, spray & lubricant techniques,and part stress calculation from shrinkage or displacement prediction after stress relief.

  4. Fluorine production in intermediate-mass stars

    CERN Document Server

    Mowlavi, N; Arnould, M

    1996-01-01

    The 19F production during the first dozen thermal pulses of AGB stars with (M=3,Z=0.02), (M=6,Z=0.02) and (M=3,Z=0.001) is investigated on grounds of detailed stellar models and of revised rates for 15N(a,g)19F and 18O(a,g)22Ne. These calculations confirm an early expectation that 19F {\\it is} produced in AGB thermal pulses. They also enlarge substantially these previous results by showing that the variations of the level of 19F production during the evolution is very sensitive to the maximum temperature reached at the base of the pulse. These variations are analyzed in detail, and are shown to result from a subtle balance between different nuclear effects (mainly 19F production or destruction in a pulse, and 15N synthesis during the interpulse), possibly super-imposed on dilution effects in more or less extended pulse convective tongues. Our calculations, as most others, do not predict the third dredge-up self- consistently. When parametrized, it appears that our models of intermediate-mass AGB stars are abl...

  5. Aerospace applications of mass market MEMS products

    Science.gov (United States)

    Bauer, Karin; Kroetz, Gerhard; Schalk, Josef; Mueller, Gerhard

    2002-07-01

    Aerospace applications of MEMS products, originally developed for automotive mass markets, are discussed. Various sensor examples with a high dual use potential are presented: inertial sensing, flow and gas sensing, robust micro sensors including SiC- and GaN-based devices, as well as first approaches towards flexible and distributed microsystems. In Europe the automotive industry is one of the main MEMS market drivers, simply because of the sheer size of this market and Europe's strong position in this industrial field. Main MEMS activities are development and integration of vehicle dynamics sensing systems, passenger safety and navigation systems, air and fuel intake systems, as well as sensor systems for exhaust gas after treatment and climate control. Benefits on the customer side are increased safety, passenger comfort and reduced fuel consumption. Benefits on the manufacturer's side are increased sub-system integration, modularity and reduced production cost. In the future the aerospace industry is likely to benefit from the introduction of micro-systems for the same reasons as the automotive industry. Interests of the aerospace industry are increasing safety and reliability of airplane operation, health and state monitoring of fuselage and airplane subsystems as well as improving service and maintenance procedures. In comparison to automotive applications, the numbers of devices needed is likely to be much smaller, however, new challenges arise in so far as distributed sensing and actuating microsystems will be needed. The idea is to identify and to exploit synergies between automotive mass market MEMS applications and lower-volume aerospace ones. The effort necessary to meet aerospace requirements and the extent of necessary trade-offs in customizing automotive MEMS is addressed considering the above-mentioned examples.

  6. Preliminary Investigation into Pyrotechnic Chemical Products via Mass Spectrometry Techniques

    Science.gov (United States)

    2015-03-11

    via Mass Spectrometry Techniques 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Jonathan Dilger, Eric...undesirable side reactions within the combustion. Mass spectrometry (MS) enables the rapid analysis of these products with instrumentation that offers...predicted by theory. 15. SUBJECT TERMS mass spectrometry , gas chromatography, pyrolysis, combustion products, pyrotechnics 16. SECURITY CLASSIFICATION OF

  7. Test masses for the G-POEM test of the weak equivalence principle

    Science.gov (United States)

    Reasenberg, Robert D.; Phillips, James D.; Popescu, Eugeniu M.

    2011-11-01

    We describe the design of the test masses that are used in the ‘ground-based principle of equivalence measurement’ test of the weak equivalence principle. The main features of the design are the incorporation of corner cubes and the use of mass removal and replacement to create pairs of test masses with different test substances. The corner cubes allow for the vertical separation of the test masses to be measured with picometer accuracy by SAO's unique tracking frequency laser gauge, while the mass removal and replacement operations are arranged so that the test masses incorporating different test substances have nominally identical gravitational properties.

  8. An Analysis of Transducer Mass Loading Effect Inshaker Testing

    Directory of Open Access Journals (Sweden)

    A. D. Karle

    2014-06-01

    Full Text Available Modal Analysis has been a developing science in the experimental evaluation of the dynamic properties of the structures. Frequency Response Function (FRF is one of the major steps in modal analysis. Measured frequency response functions (FRFs are used to extract modal parameters. It is also known that the accuracy and the reliability of various analyses using the measured FRFs depend strongly on the quality of measured data. It is well known that the quality of measured frequency response functions (FRFs is adversely affected by many factors, most significant sources being noise and systematic errors like mass loading effects of transducers. A transducer mounted on a vibrating system changes the dynamics of the structure due to the addition of extra mass and introduces errors into measured FRFs. One problem with this is the production of unrealistic results, which cause the measured resonant frequencies to be less than the correct values. These errors also lead to incorrect prediction of modal parameters. In many situations, the mass loading effect is ignored in the analytical and experimental process, based on a usual assumption that the transducer mass is negligible compared to that of the structure under test. However, when light-weighted structures are investigated, this effect can be significant.

  9. Role of Mass Media in Agricultural Productivity in Adamawa State ...

    African Journals Online (AJOL)

    Role of Mass Media in Agricultural Productivity in Adamawa State, Nigeria. ... PROMOTING ACCESS TO AFRICAN RESEARCH ... Specifically, it focused on the extent to which mass media have been used to communicate agricultural ...

  10. Design, production and materials of PV-powered consumer products - The case of mass production

    NARCIS (Netherlands)

    Reinders, A.H.M.E.; Akkerman, R.

    2005-01-01

    Though many options exist, the application of integrated PV systems in mass produced consumer products is still unusual and rare [1]. Therefore, to date, design and manufacturing aspects of product-integrated PV systems have been explored only to a very limited extent. The requirements for the desig

  11. CASE-BASED PRODUCT CONFIGURATION AND REUSE IN MASS CUSTOMIZATION

    Institute of Scientific and Technical Information of China (English)

    Wang Shiwei; Tan Jianrong; Zhang Shuyou; Wang Xin; He Chenqi

    2004-01-01

    The increasing complexity and size of configuration knowledge bases requires the provision of advanced methods supporting the development of the actual configuration process and design reuse.A new framework to find a feasible and practical product configuration method is presented in mass customization.The basic idea of the approach is to integrate case-based reasoning (CBR) with a constraint satisfaction problem(CSP).The similarity measure between a crisp and range is also given,which is common in case retrieves.Based on the configuration model,a product platform and customer needs,case adaptation is carried out with the repair-based algorithm.Lastly,the methodology in the elevator configuration design domain is tested.

  12. Inflight magnetic characterization of the test masses onboard LISA Pathfinder

    CERN Document Server

    Diaz-Aguiló, Marc; Lobo, Alberto

    2012-01-01

    LISA Pathfinder is a science and technology demonstrator of the European Space Agency within the framework of its LISA mission, the latter aiming to be the first space-borne gravitational wave observatory. The payload of LISA Pathfinder is the so-called LISA Technology Package, which is designed to measure relative accelerations between two test masses in nominal free fall. The diagnostics subsystem consists of several modules, one of which is the magnetic diagnostics unit. Its main function is the assessment of the differential acceleration noise between the test masses due to magnetic effects. This subsystem is composed of two onboard coils intended to produce controlled magnetic fields at the location of the test masses. These magnetic fields couple with the remanent magnetic moment and susceptibility and produce forces and torques on the test masses. These, in turn, produce kinematic excursions of the test masses which are sensed by the onboard interferometer. We prove that adequately processing these exc...

  13. Carotenoids in bird testes: links to body carotenoid supplies, plumage coloration, body mass and testes mass in house finches (Carpodacus mexicanus).

    Science.gov (United States)

    Rowe, Melissah; Tourville, Elizabeth A; McGraw, Kevin J

    2012-01-01

    Carotenoid pigments can be allocated to different parts of the body to serve specific functions. In contrast to other body tissues, studies of carotenoid resources in the testes of animals are relatively scarce. We used high-performance liquid chromatography to determine the types and concentrations of carotenoids in the testes of house finches (Carpodacus mexicanus). Additionally, we examined the relationships between testes carotenoid concentrations and carotenoid pools in other body tissues, as well as body mass, testes mass and plumage coloration. We detected low concentrations of several carotenoids - lutein (the predominant carotenoid), zeaxanthin, anhydrolutein, β-cryptoxanthin, β-carotene and an unknown carotene - in the testes of wild house finches. We also found that testes lutein levels were significantly and positively associated with circulating lutein levels, while the concentration of zeaxanthin in testes was positively associated with zeaxanthin levels in liver, though in this instance the relationship was much weaker and only marginally significant. Furthermore, lutein levels in testes were significantly negatively associated with testes mass. Finally, plumage coloration was not associated with either the concentration of carotenoids in the testes or relative testes mass. These results suggest that testes carotenoids are reflective of the pool of circulating carotenoids in house finches, and that plumage coloration is unlikely to signal either the carotenoid content of testes tissue or a male's capacity for sperm production.

  14. Inficon Transpector MPH Mass Spectrometer Random Vibration Test Report

    Science.gov (United States)

    Santiago-Bond, Jo; Captain, Janine

    2015-01-01

    The purpose of this test report is to summarize results from the vibration testing of the INFICON Transpector MPH100M model Mass Spectrometer. It also identifies requirements satisfied, and procedures used in the test. As a payload of Resource Prospector, it is necessary to determine the survivability of the mass spectrometer to proto-qualification level random vibration. Changes in sensitivity of the mass spectrometer can be interpreted as a change in alignment of the instrument. The results of this test will be used to determine any necessary design changes as the team moves forward with flight design.

  15. Test Marketing in New Product Development

    Science.gov (United States)

    Klompmaker, Jay E.; And Others

    1976-01-01

    Discusses the role of test marketing in new product development, based on interviews with marketing executives. Attempts to clarify when a test market should be done, what its aims should be, and how it should be used. (JG)

  16. Test Marketing in New Product Development

    Science.gov (United States)

    Klompmaker, Jay E.; And Others

    1976-01-01

    Discusses the role of test marketing in new product development, based on interviews with marketing executives. Attempts to clarify when a test market should be done, what its aims should be, and how it should be used. (JG)

  17. Production tests 300 series: A Bibliography

    Energy Technology Data Exchange (ETDEWEB)

    Schmidt, B.J.

    1957-03-01

    This bibliography is a compilation of reports on production tests performed in the 300 Area from May 1944 to February 1957. It includes all tests covering engineering and physics experiments in the Hanford Test Reactor development; fabrication and subsequent irradiation of fuel elements and melt plant (slug fabrication) procedures. Subject, author and report number indexes are included. Addendum 1 gives the reactor production test number under which the fuel elements were irradiated.

  18. Composting: Mass Balances and Product Quality

    DEFF Research Database (Denmark)

    Boldrin, Alessio; Christensen, Thomas Højlund; Körner, I.

    2011-01-01

    While the basic processes involved in composting of waste are described in Chapter 9.1 and the main composting technologies are presented in Chapter 9.2, this chapter focuses on mass balances, environmental emissions, unit process inventories and the quality of the compost produced. Understanding...

  19. A Study of Oral Production Tests

    Institute of Scientific and Technical Information of China (English)

    陈瑜

    2013-01-01

    Testing the ability to speak is a most important aspect of language testing. Testing of students’spoken English can bring in a positive washback for English teaching. However,it’s extremely difficult to test. This paper conducts a general analysis of oral production tests from overview,types and items of oral tests and scoring methods,which’s supposed to serve as an introduction to the issue under discussion.

  20. Applications of Mass Customization Production Mode in Chinese Steel Industry

    Institute of Scientific and Technical Information of China (English)

    ZhouShichun; DingJianhua; ChenChao

    2005-01-01

    In this paper, the conflict between individual needs of market and the efficient mass production requirement of manufacture under the background of market globalization is discussed, a trend that the main production mode for domestic steel industry should be the mass customization is pointed out, and the problems to be solved for domestic enterprise are analyzed. Summarizing the practice of Baosteel Co. LTD on the new production mode, the achievements and experiences are presented.

  1. Framework for product knowledge and product related knowledge which supports product modelling for mass customization

    DEFF Research Database (Denmark)

    Riis, Jesper; Hansen, Benjamin Loer; Hvam, Lars

    2003-01-01

    The article presents a framework for product knowledge and product related knowledge which can be used to support the product modelling process which is needed for developing IT systems. These IT systems are important tools for many companies when they aim at achieving mass customization and pers......The article presents a framework for product knowledge and product related knowledge which can be used to support the product modelling process which is needed for developing IT systems. These IT systems are important tools for many companies when they aim at achieving mass customization...... on experience from product modelling projects in several companies. Among them for example companies manufacturing electronic switchboards, spray dryer systems and air conditioning equipment. The framework is divided into three views: the product knowledge view, the life phase system view and the transformation...... process view (“the meeting”). The persons (rolls) involved in the product modelling process are for example: domain experts, change managers, model managers, project leaders, technical facilitators, process managers and software programmers. They need a framework during the product modelling process...

  2. Mass Independent Entropy Products in Conformal Gravity

    CERN Document Server

    Pradhan, Parthapratim

    2016-01-01

    In this work we investigate the thermodynamic properties of conformal holography in four dimensions. We compute the \\emph{area(or entropy) functional} relation for this black hole. We consider both dS and AdS cases. Thermodynamic stability is studied by computing the specific heat. The phase transition occurs at a certain condition. Various types of phase structure has been given for various values of $a$ and $\\Lambda$. In the limit $a=0$, one finds the result of Schwarzschild-dS and Schwarzschild-AdS cases. In the limit $aM<<1$, one obtains the result of Grumiler space-time. Where $a$ is defined in the metric and $M$ is the mass parameter.The \\emph{thermodynamic volume functional} relation is derived in the extended phase space. The \\emph{mass-independent} entropy functional relation and thermodynamic volume functional relation that we have derived could turn out to be an \\emph{universal} quantity.

  3. A Residual Mass Ballistic Testing Method to Compare Armor Materials or Components (Residual Mass Ballistic Testing Method)

    Energy Technology Data Exchange (ETDEWEB)

    Benjamin Langhorst; Thomas M Lillo; Henry S Chu

    2014-05-01

    A statistics based ballistic test method is presented for use when comparing multiple groups of test articles of unknown relative ballistic perforation resistance. The method is intended to be more efficient than many traditional methods for research and development testing. To establish the validity of the method, it is employed in this study to compare test groups of known relative ballistic performance. Multiple groups of test articles were perforated using consistent projectiles and impact conditions. Test groups were made of rolled homogeneous armor (RHA) plates and differed in thickness. After perforation, each residual projectile was captured behind the target and its mass was measured. The residual masses measured for each test group were analyzed to provide ballistic performance rankings with associated confidence levels. When compared to traditional V50 methods, the residual mass (RM) method was found to require fewer test events and be more tolerant of variations in impact conditions.

  4. Innovative Processes and Products for Mass Customization

    DEFF Research Database (Denmark)

    Blecker, Thorsten; Edwards, Kasper; Hvam, Lars

    This paper describes the solution developed in the KoViP project and presents the results of introducing this solution in the scope of a pilot project. The idea of the KoViP project targets SMEs of the German machine and plant manufacturing, which are forced to produce customized products whilst...... summarizes the validation of the KoViP platfor in a pilot project within the company VHV Anlagenbau, Hörstel....

  5. Sailboats, Inc.: A Fourth Grade Mass Production Program

    Science.gov (United States)

    Kazarian, Edward N.; And Others

    1976-01-01

    Describes the implementation of a hands-on minicourse on mass production designed to help students understand this industrial process. Provides instructions and pattern guide for making string-art mandala sailboats. (TA)

  6. Bubbfil spinning for mass-production of nanofibers

    Directory of Open Access Journals (Sweden)

    Chen Rou-Xi

    2014-01-01

    Full Text Available Bubbfil spinning is a generalized bubble electrospinning, including bubble spinning, blown-bubble spinning, and membrane spinning, for mass production of nanofiber. This paper shows small bubbles in liquid membrane are the best candidate for uniform nanofibers.

  7. Sailboats, Inc.: A Fourth Grade Mass Production Program

    Science.gov (United States)

    Kazarian, Edward N.; And Others

    1976-01-01

    Describes the implementation of a hands-on minicourse on mass production designed to help students understand this industrial process. Provides instructions and pattern guide for making string-art mandala sailboats. (TA)

  8. Study on Design Methodology of Mass Customization Products

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Based on introduction characteristics and classific at ion of Mass Customization (MC), the paper expounds foundations and design me thods of MC. The foundations of MC production are standardization, seriation and normality of production, guiding thought of Concurrent Engineering (CE), ap plication of CAD/CAM technology and etc. And design methods of MC products are d esign for product family, modular design, parameterization CAD, variant design, design for manufacturing (DFM) and design by customers. ...

  9. Delivering Mass-Produced Bespoke and Appealing Products

    Science.gov (United States)

    Childs, Thomas Hc; Dalgarno, Kenneth W.; McKay, Alison

    The bottleneck in introducing successful new products quickly to market is moving from factory floor manufacturing to the product design process and interfaces between designers, manufacturers and users. ‘Quality’, for products that contact people, has moved beyond functionality and usability to satisfying people’s subjective and emotional lifestyle needs. Affective (kansei) engineering design offers approaches that can be used to bring the emotional responses of consumers into the design process. In parallel, mass customisation promises the delivery of mass-produced bespoke products to individual users. Together, affective engineering and mass customisation are having a dramatic impact on the ways in which designers, engineers and manufacturers interact with each other. The challenge for leading edge manufacture is to create new product opportunities through integration of and new developments in technology, systems and design.

  10. ConocoPhillips Gas Hydrate Production Test

    Energy Technology Data Exchange (ETDEWEB)

    Schoderbek, David; Farrell, Helen; Howard, James; Raterman, Kevin; Silpngarmlert, Suntichai; Martin, Kenneth; Smith, Bruce; Klein, Perry

    2013-06-30

    Work began on the ConocoPhillips Gas Hydrates Production Test (DOE award number DE-NT0006553) on October 1, 2008. This final report summarizes the entire project from January 1, 2011 to June 30, 2013.

  11. Towards a universal product ion mass spectral library - reproducibility of product ion spectra across eleven different mass spectrometers.

    Science.gov (United States)

    Hopley, Chris; Bristow, Tony; Lubben, Anneke; Simpson, Alec; Bull, Elaine; Klagkou, Katerina; Herniman, Julie; Langley, John

    2008-06-01

    Product ion spectra produced by collision-induced dissociation (CID) in tandem mass spectrometry experiments can differ markedly between instruments. There have been a number of attempts to standardise the production of product ion spectra; however, a consensus on the most appropriate approach to the reproducible production of spectra has yet to be reached. We have previously reported the comparison of product ion spectra on a number of different types of instruments - a triple quadrupole, two ion traps and a Fourier transform ion cyclotron resonance mass spectrometer (Bristow AWT, Webb KS, Lubben AT, Halket JM. Rapid Commun. Mass Spectrom. 2004; 18: 1). The study showed that a high degree of reproducibility was achievable. The goal of this study was to improve the comparability and reproducibility of CID product ion mass spectra produced in different laboratories and using different instruments. This was carried out experimentally by defining a spectral calibration point on each mass spectrometer for product ion formation. The long-term goal is the development of a universal (instrument independent) product ion mass spectral library for the identification of unknowns. The spectra of 48 compounds have been recorded on eleven mass spectrometers: six ion traps, two triple quadrupoles, a hybrid triple quadrupole, and two quadrupole time-of-flight instruments. Initially, 4371 spectral comparisons were carried out using the data from eleven instruments and the degree of reproducibility was evaluated. A blind trial has also been carried out to assess the reproducibility of spectra obtained during LC/MS/MS. The results suggest a degree of reproducibility across all instrument types using the tuning point technique. The reproducibility of the product ion spectra is increased when comparing the tandem in time type instruments and the tandem in space instruments as two separate groups. This may allow the production of a more limited, yet useful, screening library for LC

  12. EOR production technique tested on Codell

    Energy Technology Data Exchange (ETDEWEB)

    Stremel, K.

    1983-05-01

    A production method of natural gas that eliminated marketing problems and allowed maximum recovery was dicussed. The method involved the dehydration of the gas, stripping of the propane and butane products, and the compression and reinjection of the dry gas to the well. This maintenance of pressure will allow storage of the gas until marketing conditions improve. The production method is being tested at pilot wells in Colorado by Petromax Energy Corporation.

  13. Test of pressure transducer for measuring cotton-mass flow

    Science.gov (United States)

    In this study, a cotton harvester yield monitor was developed based on the relationship between air pressure and the mass of seed cotton conveyed. The sensor theory was verified by laboratory tests. The sensor was tested on a cotton picker with seed cotton at two moisture contents, 5.9% and 8.5% we...

  14. Heat and mass transfer during baking: product quality aspects

    NARCIS (Netherlands)

    Asselman, A.; Straten, van G.; Hadiyanto, H.; Boom, R.M.; Esveld, D.C.; Boxtel, van A.J.B.

    2005-01-01

    Abstract Most food product qualities are developed during heating processes. Therefore the internal heating and mass transfer of water are important aspects in food processing. Heating of food products is mostly induced by convection heating. However, the number applications of convective heating in

  15. Heat and mass transfer during baking: product quality aspects

    NARCIS (Netherlands)

    Asselman, A.; Straten, van G.; Hadiyanto, H.; Boom, R.M.; Esveld, D.C.; Boxtel, van A.J.B.

    2005-01-01

    Abstract Most food product qualities are developed during heating processes. Therefore the internal heating and mass transfer of water are important aspects in food processing. Heating of food products is mostly induced by convection heating. However, the number applications of convective heating in

  16. 16 CFR 1209.36 - Production testing.

    Science.gov (United States)

    2010-01-01

    ... SAFETY STANDARD FOR CELLULOSE INSULATION Certification § 1209.36 Production testing. (a) General. Manufacturers, private labelers, and importers shall test the cellulose insulation periodically as it is... standard or a portion of the standard, the insulation produced during the interval will also meet the...

  17. Configuring Product Modularity and Service Modularity for Mass Customization Strategies

    DEFF Research Database (Denmark)

    Bask, Anu; Hsuan, Juliana; Rajahonka, Mervi

    Service modularity is an emerging field of research, and there has been a growing interest on how it can contribute to service design and operations management. In this study we develop a framework to assess configurations of the bundling of products and services through modularization strategies......, and how such configurations become the foundations for mass customization strategies. As a result we identify critical characteristics that are relevant for both product and services, and suggest a conceptual framework consisting of twelve dynamic mass customization strategies with paired product...... and service modularity. Case examples are used for illustration of different strategies....

  18. Configuring Product Modularity and Service Modularity for Mass Customization Strategies

    DEFF Research Database (Denmark)

    Bask, Anu; Hsuan, Juliana; Rajahonka, Mervi

    , and how such configurations become the foundations for mass customization strategies. As a result we identify critical characteristics that are relevant for both product and services, and suggest a conceptual framework consisting of twelve dynamic mass customization strategies with paired product......Service modularity is an emerging field of research, and there has been a growing interest on how it can contribute to service design and operations management. In this study we develop a framework to assess configurations of the bundling of products and services through modularization strategies...... and service modularity. Case examples are used for illustration of different strategies....

  19. Image slicer manufacturing: from space application to mass production

    Science.gov (United States)

    Bonneville, Christophe; Cagnat, Jean-François; Laurent, Florence; Prieto, Eric; Ancourt, Gérard

    2004-09-01

    This presentation aims to show technical and industrial inputs to be taking into account for Image Slicer systems design and development for different types of projects from space application to mass production for multi-IFU instruments. Cybernétix has a strong experience of precision optics assembled thanks to molecular adhesion and have already manufactured 6 prototypes of image slicer subsystem (prototypes of NIRSPEC-IFU, IFS for JWST, MUSE ...) in collaboration with the Laboratoire d"Astrophysique de Marseille (LAM) and the Centre de Recherche Astronomique de Lyon (CRAL). After a brief presentation of the principle of manufacturing and assembly, we will focus on the different performances achieved in our prototypes of slicer mirrors, pupil and slit mirrors lines: an accuracy on centre of curvature position better than 15 arsec has been obtained for a stack of 30 slices. The contribution of the slice stacking to this error is lower than 4 arcsec. In spite of very thin surfaces (~ 0.9 x 40 mm for instance), a special process allows to guarantee a surface roughness about 5 nm and very few digs on the slice borders. The WFE of the mini-mirror can also be measured at a stage of the manufacturing. Different environmental tests have shown the withstanding of these assemblies to cryogenic temperature (30 K). Then, we will describe the different solutions (spherical, flat, cylindrical surfaces) and characteristics of an image slicer that can influence difficulties of manufacturing and metrology, cost, schedule and risks with regard to fabrication. Finally, the study of a mass production plan for MUSE (CRAL) composed of 24 Image Slicers of 38 slices, that"s to say 912 slices, will be exposed as an example of what can be do for multi-module instruments.

  20. Production LHC HTS power lead test results

    CERN Document Server

    Tartaglia, M; Fehér, S; Huang, Y; Orris, D F; Pischalnikov, Y; Rabehl, Roger Jon; Sylvester, C D; Zbasnik, J

    2005-01-01

    The Fermilab Magnet test facility has built and operated a test stand to characterize the performance of HTS power leads. We report here the results of production tests of 20 pairs of 7.5 kA HTS power leads manufactured by industry for installation in feed boxes for the LHC Interaction Region quadrupole strings. Included are discussions of the thermal, electrical, and quench characteristics under "standard" and "extreme" operating conditions, and the stability of performance across thermal cycles.

  1. Note: Discharging fused silica test masses with ionized nitrogen

    Science.gov (United States)

    Ugolini, D.; Funk, Q.; Amen, T.

    2011-04-01

    We have developed a technique for discharging fused silica test masses in a gravitational-wave interferometer with nitrogen ionized by an electron beam. The electrons are produced from a heated filament by thermionic emission in a low-pressure region to avoid contamination and burnout. Some electrons then pass through a small aperture and ionize nitrogen in a higher-pressure region, and this ionized gas is pumped across the test mass surface, neutralizing both polarities of charge. The discharge rate varies exponentially with charge density and filament current, quadratically with filament potential, and has an optimal working pressure of ˜8 mT. Adapting the technique to larger test mass chambers is also discussed.

  2. Top-quark pair production in a running mass scheme

    Energy Technology Data Exchange (ETDEWEB)

    Dowling, M. [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Moch, S. [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Hamburg Univ. (Germany). II. Inst. fuer Theoretische Physik

    2013-11-15

    Between the Tevatron and LHC, top-quark physics is now becoming an area for precision physics. This has lead to an increase in theoretical activity to match the experimental accuracy of top anti-top production. We discuss the difficulty in properly defining the top-quark mass as measured by experiments and present results for differential distributions of top-quark pair production in a running mass scheme. The use of such a scheme shows better convergence in the perturbative expansion and improves the scale dependence as opposed to the typical on-shell scheme.

  3. Cost-Effective Mass Production of Mono Bucket Foundations

    DEFF Research Database (Denmark)

    Gres, Szymon; Nielsen, Søren Andreas; Fejerskov, Morten

    2015-01-01

    No recognized procedures exist for the Mono Bucket Foundation design, which is an obstruction for mass customization/production and industrialization in relation to certifying authorities. This paper presents the outcome of on-going research and development program that provides solution for inno......No recognized procedures exist for the Mono Bucket Foundation design, which is an obstruction for mass customization/production and industrialization in relation to certifying authorities. This paper presents the outcome of on-going research and development program that provides solution...

  4. Old star clusters: Bench tests of low mass stellar models

    Directory of Open Access Journals (Sweden)

    Salaris M.

    2013-03-01

    Full Text Available Old star clusters in the Milky Way and external galaxies have been (and still are traditionally used to constrain the age of the universe and the timescales of galaxy formation. A parallel avenue of old star cluster research considers these objects as bench tests of low-mass stellar models. This short review will highlight some recent tests of stellar evolution models that make use of photometric and spectroscopic observations of resolved old star clusters. In some cases these tests have pointed to additional physical processes efficient in low-mass stars, that are not routinely included in model computations. Moreover, recent results from the Kepler mission about the old open cluster NGC6791 are adding new tight constraints to the models.

  5. Testing galaxy formation models with galaxy stellar mass functions

    Science.gov (United States)

    Lim, S. H.; Mo, H. J.; Lan, Ting-Wen; Ménard, Brice

    2016-10-01

    We compare predictions of a number of empirical models and numerical simulations of galaxy formation to the conditional stellar mass functions (CSMF) of galaxies in groups of different masses obtained recently by Lan et al. to test how well different models accommodate the data. The observational data clearly prefer a model in which star formation in low-mass halos changes behavior at a characteristic redshift zc ˜ 2. There is also tentative evidence that this characteristic redshift depends on environment, becoming zc ˜ 4 in regions that eventually evolve into rich clusters of galaxies. The constrained model is used to understand how galaxies form and evolve in dark matter halos, and to make predictions for other statistical properties of the galaxy population, such as the stellar mass functions of galaxies at high z, the star formation and stellar mass assembly histories in dark matter halos. A comparison of our model predictions with those of other empirical models shows that different models can make vastly different predictions, even though all of them are tuned to match the observed stellar mass functions of galaxies.

  6. Testing galaxy formation models with galaxy stellar mass functions

    Science.gov (United States)

    Lim, S. H.; Mo, H. J.; Lan, T.-W.; Ménard, B.

    2017-01-01

    We compare predictions of a number of empirical models and numerical simulations of galaxy formation to the conditional stellar mass functions of galaxies in groups of different masses obtained recently by Lan et al. to test how well different models accommodate the data. The observational data clearly prefer a model in which star formation in low-mass haloes changes behaviour at a characteristic redshift zc ˜ 2. There is also tentative evidence that this characteristic redshift depends on environment, becoming zc ˜ 4 in regions that eventually evolve into rich clusters of galaxies. The constrained model is used to understand how galaxies form and evolve in dark matter haloes, and to make predictions for other statistical properties of the galaxy population, such as the stellar mass functions of galaxies at high z, the star formation, and stellar mass assembly histories in dark matter haloes. A comparison of our model predictions with those of other empirical models shows that different models can make vastly different predictions, even though all of them are tuned to match the observed stellar mass functions of galaxies.

  7. Production Cost Optimization Model Based on CODP in Mass Customization

    Directory of Open Access Journals (Sweden)

    Yanhong Qin

    2013-01-01

    Full Text Available The key for enterprises to implement the postponement strategy is the right decision on the location of Customer Order Decoupling Point (CODP so as to achieve the scope economics of mass customization and scale economics of mass production fully. To deal with production cost optimization problem of postponement system based on various situation of CODP, a basic model of production cost and its M/M/1 extended model are proposed and compared so as to optimize the overall production cost of the postponement system. The production modes can be classified as MTS (make to stock, ATO (assemble to order, MTO (make to order and ETO (engineering to order according to the inventory location, and the postponed production system considered here includes manufacturing cost, semi-finished inventory cost and customer waiting cost caused by delaying delivery. By Matlab simulation, we can compute the optimal location of CODP in each production mode, which can provide some management insight for the manufacturer to decide the right production mode and utilize the resources efficiently.

  8. Between Product Development and Mass Production: Tensions as Triggers for Concept-Level Learning

    Science.gov (United States)

    Jalonen, Meri; Ristimäki, Päivi; Toiviainen, Hanna; Pulkkis, Anneli; Lohtander, Mika

    2016-01-01

    Purpose: This paper aims to analyze learning in organizational transformations by focusing on concept-level tensions faced in two young companies, which were searching for a reorientation of activity with a production network between innovative product development and efficient mass production. Design/methodology/approach: An intervention-based…

  9. Low-Level waste phase 1 melter testing off gas and mass balance evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Wilson, C.N.

    1996-06-28

    Commercially available melter technologies were tested during 1994-95 as part of a multiphase program to test candidate technologies for vitrification of the low-level waste (LLW) stream to be derived from retrieval and pretreatment of Hanford Site tank wastes. Seven vendors were selected for Phase 1 testing to demonstrate vitrification of a high sodium content liquid LLW simulant. The tested melter technologies included four Joule-heated melters, a carbon electrode melter, a combustion melter, and a plasma melter. Various dry and slurry melter feed preparation processes were also tested. Various feed material samples, product glass samples, and process offgas streams were characterized to provide data for evaluation of process decontamination factors and material mass balances for each vitrification technology. This report describes the melter mass balance evaluations and results for six of the Phase 1 LLW melter vendor demonstration tests.

  10. Mass customization and build to order production - in manufacturing networks

    DEFF Research Database (Denmark)

    Svensson, Carsten

    2003-01-01

    Mass Customization and Build to Order Production – In Manufacturing Networks Mass customization and globalization have radically changed the environment for manufacturers. A new context is emerging with intensified competition and accelerated technology development. In this environment evolution...... in the manufacturing as information processing is accountable for an increasing portion of the value creation. In order to improve the information processing some manufacturers have applied product models, thereby giving the customer access to the manufactures knowledge base. This project will introduce solution...... elements, which can support an improved utilization of product models in relation to new and existing manufacturing systems. The scientific novelty of this project is the exposure of the potential that lies in an improved application and integration of information technology in the supply chain...

  11. Mass customization and build to order production - in manufacturing networks

    DEFF Research Database (Denmark)

    Svensson, Carsten

    2003-01-01

    elements, which can support an improved utilization of product models in relation to new and existing manufacturing systems. The scientific novelty of this project is the exposure of the potential that lies in an improved application and integration of information technology in the supply chain...... to the specification task thereby enabling the coordination of orders through the supply chain. Furthermore the strategic importance of a well structured supply chain is discussed and the potential value of the application of product models in the supply chain is emphasised. In this project the interface between......Mass Customization and Build to Order Production – In Manufacturing Networks Mass customization and globalization have radically changed the environment for manufacturers. A new context is emerging with intensified competition and accelerated technology development. In this environment evolution...

  12. 75 FR 28335 - Testing and Labeling Pertaining to Product Certification

    Science.gov (United States)

    2010-05-20

    ... Safety Commission 16 CFR Part 1107 Testing and Labeling Pertaining to Product Certification; Proposed... Product Certification AGENCY: Consumer Product Safety Commission. ACTION: Proposed rule. SUMMARY: The... product complies with certification requirements under a reasonable testing program for...

  13. MICROBIOLOGICAL TESTING OF SELECTED CONFECTIONERY PRODUCTS QUALITY

    Directory of Open Access Journals (Sweden)

    Ľubomíra Juhaniaková

    2014-02-01

    Full Text Available The aim of this work was to determine microbiological quality and water activity of confectionery products as corpus of desserts, stuffing cakes and finished cakes. In confectionery products microbiological parameters: total count of bacteria, coliforms bacteria, mesophilic aerobic bacteria, yeasts, microscopic filamentous fungi, counts of Staphylococcus aureus and Salmonella spp. were observed. These confectionery products were evaluated: 5 corpus of Kremeš, 5 stuffing of Kremeš and 5 Venček cake. For microbiological tests 15 samples of confectionery products were used. The numbers of total count of bacteria ranged from 2.9 to 3.65 log CFU.g-1, the number of mesophilic aerobic bacteria ranged from 2.00 to 3.28 log CFU.g-1, coliforms bacteria in confectionery products ranged from 0.00 to 3.15 CFU.g-1, number of yeasts ranged from 0.00 to 3.30 log CFU.g-1and the number of microscopic fungi ranged from 0.00 to 2.90 CFU.g-1. None of the samples showed any growth of coliforms bacteria, Staphylococcus aureus and Salmonella spp. From microscopic fungi were isolated genera Alternaria, Aspergillus and Penicillium. Eight from fifteen investigated samples of confectionary products were in accordance with the Codex Alimentarius of the Slovak Republic. The lowest water activity was found in Kremeš corpus samples (0.953 and higher in Venček samples (0.973.

  14. Atom interferometry in the presence of an external test mass

    CERN Document Server

    Dubetsky, B; Libby, S B; Berman, P R

    2016-01-01

    The influence of an external test mass on the phase of the signal of an atom interferometer is studied theoretically. Using traditional techniques in atom optics based on the density matrix equations in the Wigner representation, we are able to extract the various contributions to the phase of the signal associated with the classical motion of the atoms, the quantum correction to this motion resulting from atomic recoil that is produced when the atoms interact with Raman field pulses, and quantum corrections to the atomic motion that occur in the time between the Raman field pulses. By increasing the effective wave vector associated with the Raman field pulses using modified field parameters, we can increase the sensitivity of the signal to the point where the quantum corrections can be measured. The expressions that are derived can be evaluated numerically to isolate the contribution to the signal from an external test mass. The regions of validity of the exact and approximate expressions are determined.

  15. How can we test the neutrino mass seesaw mechanism experimentally?

    Science.gov (United States)

    Buckley, Matthew R; Murayama, Hitoshi

    2006-12-01

    The seesaw mechanism for the small neutrino mass has been a popular paradigm, yet it has been believed that there is no way to test it experimentally. We present a conceivable outcome from future experiments that would convince us of the seesaw mechanism. It would involve data from the CERN Large Hadron Collider, International Linear Collider, cosmology, underground, and low-energy flavor experiments to establish the case.

  16. Proposed production test for reducing minimum downtime

    Energy Technology Data Exchange (ETDEWEB)

    Jaklevick, J.F.

    1961-11-29

    The object of the production test described in this report is to evaluate the operational aspects of a proposed method for reducing minimum downtime. The excess xenon poisoning, which occurs during the first 32--38 hours after the shutdown of a reactor from present equilibrium levels, will be partially overridden by a central enriched zone whose added reactivity contribution would be compensated during normal operation by means of poison splines.

  17. Dual-Resonator Speed Meter for a Free Test Mass

    CERN Document Server

    Braginsky, V B; Khalili, F Ya; Thorne, K S; Braginsky, Vladimir B.; Gorodetsky, Mikhail L.; Khalili, Farid Ya.; Thorne, Kip S.

    2000-01-01

    A description and analysis are given of a ``speed meter'' for monitoring a classical force that acts on a test mass. This speed meter is based on two microwave resonators (``dual resonators''), one of which couples evanescently to the position of the test mass. The sloshing of the resulting signal between the resonators, and a wise choice of where to place the resonators' output waveguide, produce a signal in the waveguide that (for sufficiently low frequencies) is proportional to the test-mass velocity (speed) rather than its position. This permits the speed meter to achieve force-measurement sensitivities better than the standard quantum limit (SQL), both when operating in a narrow-band mode and a wide-band mode. A scrutiny of experimental issues shows that it is feasible, with current technology, to construct a demonstration speed meter that beats the wide-band SQL by a factor 2. A concept is sketched for an adaptation of this speed meter to optical frequencies; this adaptation forms the basis for a possib...

  18. Production and test of the LHCb Muon Chamber

    CERN Multimedia

    2005-01-01

    - The Muon System of LHCb - The Multi-Wire Proportional Chambers for LHCb - Wire tension meter - Wire pitch measurement - Gas leakage test - Test with cosmic rays - Production and test summary - Gap gain uniformity - Production and test summary

  19. Tester Board for testing mass-produced SMB modules for CMS Preshower

    Science.gov (United States)

    Velikzhanin, Y. S.; Chou, C. H.; Hsiung, Y. B.; Lee, Y. J.; Shiu, J. G.; Sun, C. D.; Wang, Y. Z.

    2007-09-01

    We have developed a Tester Board to test the electrical characteristics of the System Motherboard (SMB) for the CMS Preshower detector at CERN. The board is designed to test input resistances, output resistances, connections, interconnections and possible short- circuits of a module having up to 640 connector pins. The Tester Board is general-purpose in nature: it could be used to test any electronic module or cable by using dedicated cable sets. The module can detect a variety of problems not detected by either functional tests or the "flying probes" technique. The design, algorithms and results of using the Tester Board during mass production of CMS Preshower SMBs are presented.

  20. Tester Board for testing mass-produced SMB modules for CMS Preshower

    CERN Document Server

    Velikzhanin, Yu S; Hsiung, Y B; Lee, Y J; Shiu, J G; Sun, C D; Wang, Y Z

    2007-01-01

    We have developed a Tester Board to test the electrical characteristics of the System Motherboard (SMB) for the CMS Preshower detector at CERN. The board is designed to test input resistances, output resistances, connections, interconnections and possible short- circuits of a module having up to 640 connector pins. The Tester Board is general-purpose in nature: it could be used to test any electronic module or cable by using dedicated cable sets. The module can detect a variety of problems not detected by either functional tests or the "flying probes" technique. The design, algorithms and results of using the Tester Board during mass production of CMS Preshower SMBs are presented.

  1. Force Limited Random Vibration Test of TESS Camera Mass Model

    Science.gov (United States)

    Karlicek, Alexandra; Hwang, James Ho-Jin; Rey, Justin J.

    2015-01-01

    The Transiting Exoplanet Survey Satellite (TESS) is a spaceborne instrument consisting of four wide field-of-view-CCD cameras dedicated to the discovery of exoplanets around the brightest stars. As part of the environmental testing campaign, force limiting was used to simulate a realistic random vibration launch environment. While the force limit vibration test method is a standard approach used at multiple institutions including Jet Propulsion Laboratory (JPL), NASA Goddard Space Flight Center (GSFC), European Space Research and Technology Center (ESTEC), and Japan Aerospace Exploration Agency (JAXA), it is still difficult to find an actual implementation process in the literature. This paper describes the step-by-step process on how the force limit method was developed and applied on the TESS camera mass model. The process description includes the design of special fixtures to mount the test article for properly installing force transducers, development of the force spectral density using the semi-empirical method, estimation of the fuzzy factor (C2) based on the mass ratio between the supporting structure and the test article, subsequent validating of the C2 factor during the vibration test, and calculation of the C.G. accelerations using the Root Mean Square (RMS) reaction force in the spectral domain and the peak reaction force in the time domain.

  2. Slant Hole Completion Test, Cozzette and Paludal production testing

    Energy Technology Data Exchange (ETDEWEB)

    Mann, R.L.; Malinowsky, M.S.

    1993-12-31

    The Slant Hole Completion Test has been successful in providing good technology transfer to the oil and gas industry. The gas-producing rate from the Cozzette horizontal open-hole interval was significantly greater than from offset vertical wells. The source of water production from the Cozzette is not presently understood. Diagnosis of the water production mechanism is vital to economic exploitation of the Cozzette gas resource using horizontal well technology. Stimulation in a high-angle cased and cemented wellbore, such as the Paludal 2, 3 and 4 intervals in SHCT No. 1, is more difficult because of high near-wellbore stress that results in higher treating pressures. Low gas production potential following the Paludal 2, 3 and 4 stimulation may result from damage to the natural fracture system resulting from casing cementing operations. Comparison of gas production rates in SHCT No. 1 and MWX No. 1 following similar stimulations in the Paludal 3 and 4 intervals, indicate there is no advantage to a hydraulic fracture treatment in a slant wellbore when compared to a vertical wellbore.

  3. Modelling and visualising modular product architectures for mass customisation

    DEFF Research Database (Denmark)

    Mortensen, Niels Henrik; Pedersen, Rasmus; Kvist, Morten

    2008-01-01

    that the companies are striving for variety from a commercial- and simplicity from a manufacturing one. A conscious structuring of product architectures and/or the use of product platforms can help overcome this challenge. This paper presents a new method for the synthesis and visualisation of product architecture......Companies following a mass customisation strategy have to observe two prerequisites for success: they have to fulfil a wide variety of customer needs and demands, and to harvest the benefits from economies of scale within their organisation and supply chain. This leads to the situation...... concepts that puts emphasis on variety in markets while also treating the consequences in the manufacturing set-up. The work is based on the assumption that a graphical overview of a given solution space and relations between market demands, product architecture and manufacturing layout can support...

  4. Mobile materials handling platform interface architecture for mass production environments

    CSIR Research Space (South Africa)

    Walker, A

    2008-01-01

    Full Text Available stream_source_info Walker_2008.pdf.txt stream_content_type text/plain stream_size 19709 Content-Encoding UTF-8 stream_name Walker_2008.pdf.txt Content-Type text/plain; charset=UTF-8 Mobile Materials Handling Platform... to the operational structure of mass customisation, passive methods alone cannot facilitate customer influenced production dynamics. This is due to the fact that every product is different from the last. Active methods such as flexible materials handling systems...

  5. Expanded newborn screening by mass spectrometry: New tests, future perspectives.

    Science.gov (United States)

    Ombrone, Daniela; Giocaliere, Elisa; Forni, Giulia; Malvagia, Sabrina; la Marca, Giancarlo

    2016-01-01

    Tandem mass spectrometry (MS/MS) has become a leading technology used in clinical chemistry and has shown to be particularly sensitive and specific when used in newborn screening (NBS) tests. The success of tandem mass spectrometry is due to important advances in hardware, software and clinical applications during the last 25 years. MS/MS permits a very rapid measurement of many metabolites in different biological specimens by using filter paper spots or directly on biological fluids. Its use in NBS give us the chance to identify possible treatable metabolic disorders even when asymptomatic and the benefits gained by this type of screening is now recognized worldwide. Today the use of MS/MS for second-tier tests and confirmatory testing is promising especially in the early detection of new disorders such as some lysosomal storage disorders, ADA and PNP SCIDs, X-adrenoleucodistrophy (X-ALD), Wilson disease, guanidinoacetate methyltransferase deficiency (GAMT), and Duchenne muscular dystrophy. The new challenge for the future will be reducing the false positive rate by using second-tier tests, avoiding false negative results by using new specific biomarkers and introducing new treatable disorders in NBS programs.

  6. Simple, inexpensive media for mass production of three entomophthoralean fungi.

    Science.gov (United States)

    Leite, Luis G; Alves, Sérgio B; Batista Filho, Antonio; Roberts, Donald W

    2005-03-01

    The entomophthoralean fungi Batkoa sp., Furia sp. and Neozygites floridana have been suggested for biocontrol of insect pests: the first two for control of spittlebug pests of pasture and sugarcane, and the third for mites of agricultural importance. To develop these agents as biopesticides and bioacaricides, it is important to have available culture media that maximize production at low cost. The research reported here evaluates, in different combinations and concentrations, the effect of four complex sources of nitrogen on production of mycelium or hyphal bodies in liquid media of all three species. Yeast extract allowed the highest production of Batkoa sp., with a concentration of 0.5% being the most suitable for vegetative (mycelial) growth. The combination of 0.33% each of yeast extract + beef extract + skim milk allowed the highest production of Furia sp. Mycelium. The combination of yeast extract + skim milk (0.5% of each) allowed the second highest production of Furia sp., and was the most suitable for mass production due to the lower cost. The combination of 1 %each of yeast extract + peptone + skim milk was the most suitable for production of N. floridana hyphal bodies.

  7. Towards high-precision mass measurements of neutron-rich fission products at TRIGA-SPEC

    Energy Technology Data Exchange (ETDEWEB)

    Nagy, Szilard [Max-Planck-Institut fuer Kernphysik, Heidelberg (Germany); GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, Darmstadt (Germany)

    2010-07-01

    TRIGA-TRAP, the only Penning trap mass spectrometer worldwide at a nuclear research reactor, is installed at TRIGA Mainz as part of the TRIGA-SPEC experiment. The scientific goal is to perform high-precision mass measurements on lanthanoids, actinoids and neutron-rich fission products produced by thermal neutron induced fission of a target inside the reactor. High-precision mass data are scarce in this region of the nuclear chart, and further experimental data are needed for nuclear structure studies of heavy elements, to test the predictive power of nuclear mass models, or as input to nucleosynthesis calculations of the astrophysical r-process. Ions of certain lanthanoids and most actinoids as well as carbon clusters for calibration purposes can be routinely produced by a newly developed non-resonant laser ablation ion source, allowing off-line mass measurements. Besides fundamental research, TRIGA-TRAP serves as a test bench for the development of efficient ion detection techniques, which will enable mass measurements ultimately on a single ion with a half-life of the order of one second. To this end, a unique combination of the commonly used time-of-flight technique and the non-destructive image current detection method is realized in an on-line mass spectrometer. The first mass measurement results are reported.

  8. Test Guideline Methods for Bed Bug Pesticide Products Now Available

    Science.gov (United States)

    EPA’s final test guidelines, 810.3900 - Laboratory Product Performance Testing Methods for Bed Bug Pesticide Products, provides recommendations for the design and execution of laboratory studies to evaluate the performance of pesticide products.

  9. A multivariate rank test for comparing mass size distributions

    KAUST Repository

    Lombard, F.

    2012-04-01

    Particle size analyses of a raw material are commonplace in the mineral processing industry. Knowledge of particle size distributions is crucial in planning milling operations to enable an optimum degree of liberation of valuable mineral phases, to minimize plant losses due to an excess of oversize or undersize material or to attain a size distribution that fits a contractual specification. The problem addressed in the present paper is how to test the equality of two or more underlying size distributions. A distinguishing feature of these size distributions is that they are not based on counts of individual particles. Rather, they are mass size distributions giving the fractions of the total mass of a sampled material lying in each of a number of size intervals. As such, the data are compositional in nature, using the terminology of Aitchison [1] that is, multivariate vectors the components of which add to 100%. In the literature, various versions of Hotelling\\'s T 2 have been used to compare matched pairs of such compositional data. In this paper, we propose a robust test procedure based on ranks as a competitor to Hotelling\\'s T 2. In contrast to the latter statistic, the power of the rank test is not unduly affected by the presence of outliers or of zeros among the data. © 2012 Copyright Taylor and Francis Group, LLC.

  10. Identification by CI-mass spectrometry of an unexpected benzodiazepine degradation product

    Science.gov (United States)

    Buret, D.; Breton, D.; Clair, P.; Lafosse, M.

    2006-01-01

    The French Military Health Service (SSA) has developed an innovative drug product, as a treatment against neurotoxic organophosphate poisoning (NOP). It contains three drug substances: an anticholinergic, an anticonvulsant and a cholinesterase reactivator. Testing stability study, in normal conditions, over 18 months, for this speciality, has given unexpected results. Indeed, one of the drug substances, avizafone (pro-drug of diazepam), breaks down partially into a compound which migrates into the plastic container where this degradation product is demethylated after absorption. Mass spectrometry with negative chemical ionisation (negative CI-MS) was used, to monitor decomposition of the drug substance. This method first showed migration of the degradation product and has been used to monitor its evolution during the stability testing study. The demethylation seems to be due to an additive product present in the plastic. The degradation products remain trapped in the container holding the pharmaceutical formulation.

  11. Testing galaxy formation models with galaxy stellar mass functions

    CERN Document Server

    Lim, Seunghwan; Lan, Ting-Wen; Ménard, Brice

    2016-01-01

    We compare predictions of a number of empirical models and numerical simulations of galaxy formation to the conditional stellar mass functions (CSMF) of galaxies in groups of different masses obtained recently by Lan et al. to test how well different models accommodate the data. Among all the models considered, only the model of Lu et al. can match the observational data; all other models fail to reproduce the faint-end upturn seen in the observation. The CSMFs are used to update the halo-based empirical model of Lu et al., and the model parameters obtained are very similar to those inferred by Lu et al. from a completely different set of observational constraints. The observational data clearly prefer a model in which star formation in low-mass halos changes behavior at a characteristic redshift $z_c \\sim 2$. There is also tentative evidence that this characteristic redshift depends on environments, becoming $z_c \\sim 4$ in regions that eventually evolve into rich clusters of galaxies. The constrained model ...

  12. Testing different stellar mass estimators at 1

    CERN Document Server

    Longhetti, Marcella; Mignano, Arturo

    2008-01-01

    Physical parameters of galaxies (as luminosity, stellar mass, age) are often derived by means of the model templates which best fit their spectro-photometric data. We have performed a quantitative test aimed at exploring the ability of this procedure in recovering the physical parameters of early-type galaxies at 1mass, are used to build mock photometric catalogs with wavelength coverage and photometric uncertainties similar to those of two topical surveys (i.e. VVDS and GOODS). The best fitting analysis of the simulated photometric data allows to study the differences among the recovered parameters and the input ones. Results indicate that the stellar masses measured by means of optical bands are affected by larger uncertainties with respect to those obtained from near-IR bands, and they frequently underestimate the real values. The M/L ratio in the V band results strongly underestimated,...

  13. Cost-Effective Mass Production of Mono Bucket Foundations

    DEFF Research Database (Denmark)

    Nielsen, Søren A.; Ibsen, Lars Bo; Gres, Szymon

    foundations where mass production is needed. The project is planed for a duration of 3 years and is supported by Innovation Fund Denmark and has the following partners: DTU Wind Energy, FORCE Technology, LIC Engineering, AAU Civil and M-tech. The € 4 mill. project involves more than 25 researchers, Ph......Today, the basis for design and manufacturing of offshore foundations is inherited from oil and gas industry where the small repeatability in manufacturing is the case and the cost implications are different. The total opposite is the case when considering offshore Wind Turbine Generator...

  14. Mass shell smearing effects in top pair production

    CERN Document Server

    Kuksa, V I; Vlasenko, D E

    2011-01-01

    The top quark pair production and decay are considered in the framework of the smeared-mass unstable particles model. The results for total and differential cross sections in vicinity of $t\\bar{t}$ threshold are in good agreement with the previous ones in the literature. The strategy of calculations of the higher order corrections in the framework of the model is discussed. Suggested approach significantly simplifies calculations compared to the standard perturbative one and can serve as a convenient tool for fast and precise preliminary analysis of processes involving intermediate time-like top quark exchanges in the near-threshold region.

  15. RESEARCH ON MICROWAVE HUMIDITY TESTING OF CERAMIC PRODUCTS

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    This paper analyses the principle of microwave humidity testing. According to the problems in the production procedure of ceramic products, a microwave humidity testing system is designed and analyzed for its advantages. Furthermore, the system has been applied to the production line that produces ceramic products and the testing results are also satisfying.

  16. Design, production and materials of PV powered consumer products - the case of mass production (cd-rom)

    NARCIS (Netherlands)

    Reinders, Angelina H.M.E.; Akkerman, Remko; Palz, W.; Ossenbrink, H.; Helm, P.

    2005-01-01

    Though many options exist, the application of integrated PV systems in mass produced consumer products is still unusual and rare [1]. Therefore, to date, design and manufacturing aspects of product-integrated PV systems have been explored only to a very limited extent. The requirements for the desig

  17. Design, production and materials of PV powered consumer products - the case of mass production (cd-rom)

    NARCIS (Netherlands)

    Reinders, Angelina H.M.E.; Akkerman, Remko; Palz, W.; Ossenbrink, H.; Helm, P.

    2005-01-01

    Though many options exist, the application of integrated PV systems in mass produced consumer products is still unusual and rare [1]. Therefore, to date, design and manufacturing aspects of product-integrated PV systems have been explored only to a very limited extent. The requirements for the

  18. RECONFIGURABLE PRODUCT ROUTING AND CONTROL FOR MASS CUSTOMISATION MANUFACTURING

    Directory of Open Access Journals (Sweden)

    A. J. Walker

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT:Reconfigurable control of flexible manufacturing systems can allow for the efficient and responsive production of customised product instances. This can aid in providing make-to-order business models for various small- to medium-sized enterprises in South Africa, and provide competitive advantage in a dynamic global marketplace. Reconfigurable control application requires an understanding of the modes of production variability in mass customisation manufacturing. Temporally uncorrelated workflow routings are considered as one of these production variability modes. In this light, this paper addresses the flexible material payload routing problem, and presents a mobile robot platform that has been developed to research and design reconfigurable routing systems.

    AFRIKAANSE OPSOMMING:Verstelbare beheer van aanpasbare vervaardigingstelsels kan die doeltreffende en reaktiewe produksie van doelgemaakte produkeksemplare toelaat. Hierdie beheer kan assisteer in die voorsiening van vervaardig-na-bestellingbesigheidsmodelle aan ’n aantal klein- tot medium-grootte ondernemings in Suid-Afrika, en aan hulle ’n kompeterende voorsprong bied in ’n dinamiese globale mark. Die instelling van verstelbare beheer vereis dat die modi van produkveranderlikheid in massa verbruikersaanpassingsvervaardiging verstaan word. Hierdie artikel spreek die probleem van aanpasbare roetebepaling van materiaalvragte in massa verbruikersaanpassingsvervaardiging aan. ’n Mobiele robot-platform, ontwikkel vir navorsing in verstelbare roetebepalingstelsels, word ook voorgelê.

  19. Mass production of silicon pore optics for ATHENA

    Science.gov (United States)

    Wille, Eric; Bavdaz, Marcos; Collon, Maximilien

    2016-07-01

    Silicon Pore Optics (SPO) provide high angular resolution with low effective area density as required for the Advanced Telescope for High Energy Astrophysics (Athena). The x-ray telescope consists of several hundreds of SPO mirror modules. During the development of the process steps of the SPO technology, specific requirements of a future mass production have been considered right from the beginning. The manufacturing methods heavily utilise off-the-shelf equipment from the semiconductor industry, robotic automation and parallel processing. This allows to upscale the present production flow in a cost effective way, to produce hundreds of mirror modules per year. Considering manufacturing predictions based on the current technology status, we present an analysis of the time and resources required for the Athena flight programme. This includes the full production process starting with Si wafers up to the integration of the mirror modules. We present the times required for the individual process steps and identify the equipment required to produce two mirror modules per day. A preliminary timeline for building and commissioning the required infrastructure, and for flight model production of about 1000 mirror modules, is presented.

  20. Determination of membrane degradation products in the product water of polymer electrolyte membrane fuel cells using liquid chromatography mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Zedda, Marco

    2011-05-12

    The predominant long term failure of polymer electrolyte membranes (PEM) is caused by hydroxyl radicals generated during fuel cell operation. These radicals attack the polymer, leading to chain scission, unzipping and consequently to membrane decomposition products. The present work has investigated decomposition products of novel sulfonated aromatic hydrocarbon membranes on the basis of a product water analysis. Degradation products from the investigated membrane type and the possibility to detect these compounds in the product water for diagnostic purposes have not been discovered yet. This thesis demonstrates the potential of solid phase extraction and liquid chromatography tandem mass spectrometry (SPE-LC-MS/MS) for the extraction, separation, characterization, identification and quantification of membrane degradation products in the product water of fuel cells. For this purpose, several polar aromatic hydrocarbons with different functional groups were selected as model compounds for the development of reliable extraction, separation and detection methods. The results of this thesis have shown that mixed mode sorbent materials with both weak anion exchange and reversed phase retention properties are well suited for reproducible extraction of both molecules and ions from the product water. The chromatographic separation of various polar aromatic hydrocarbons was achieved by means of phase optimized liquid chromatography using a solvent gradient and on a C18 stationary phase. Sensitive and selective detection of model compounds could be successfully demonstrated by the analysis of the product water using tandem mass spectrometry. The application of a hybrid mass spectrometer (Q Trap) for the characterization of unknown polar aromatic hydrocarbons has led to the identification and confirmation of 4-hydroxybenzoic acid in the product water. In addition, 4-HBA could be verified as a degradation product resulting from PEM decomposition by hydroxyl radicals using an

  1. A First Mass Production of Gas Electron Multipliers

    CERN Document Server

    Barbeau, P S; Geissinger, J D; Miyamoto, J; Shipsey, I; Yang, R

    2003-01-01

    We report on the manufacture of a first batch of approximately 2,000 Gas Electron Multipliers (GEMs) using 3M's fully automated roll to roll flexible circuit production line. This process allows low-cost, reproducible fabrication of a high volume of GEMs of dimensions up to 30$\\times$30 cm$^{2}$. First tests indicate that the resulting GEMs have optimal properties as radiation detectors. Production techniques and preliminary measurements of GEM performance are described. This now demonstrated industrial capability should help further establish the prominence of micropattern gas detectors in accelerator based and non-accelerator particle physics, imaging and photodetection.

  2. Low mass dimuon production with the ALICE muon spectrometer

    CERN Document Server

    Casula, Ester Anna Rita

    Low mass vector meson ($\\rho$, $\\omega$, $\\phi$) production provides key information on the hot and dense state of strongly interacting matter produced in high-energy heavy ion collisions (called Quark Gluon Plasma). Strangeness enhancement is one of the possible signatures of the Quark Gluon Plasma formation and can be accessed through the measurement of $\\phi$ meson production with respect to $\\rho$ and $\\omega$ mesons, while the measurement of the $\\phi$ nuclear modification factor provides a powerful tool to probe the production dynamics and hadronization process in relativistic heavy ion collisions. Vector mesons can be detected through their decays into muon pairs with the ALICE muon spectrometer. This thesis presents the results on the measurement of the $\\phi$ differential cross section, as a function of the transverse momentum, in pp collisions at $\\sqrt{s}$ = 2.76 TeV; the measurement of the $\\phi$ yield and of the nuclear modification factor $R_{pA}$ at forward and backward rapidity, as a function...

  3. Probing Radiative Neutrino Mass Generation through Monotop Production

    CERN Document Server

    Ng, John N

    2014-01-01

    We present a generalization of a model where the right-handed up-type quarks serve as messengers for neutrino mass generation and as a portal for dark matter. Within this framework the Standard Model is extended with a single Majorana neutrino, a coloured electroweak-singlet scalar and a coloured electroweak-triplet scalar. We calculate the relic abundance of dark matter and show that we can match the latest experimental results. Furthermore, the implications from the scattering between nuclei and the dark matter candidate are studied and we implement the latest experimental constraints arising from flavour changing interactions, Higgs production and decay and LHC collider searches for a single jet and jets plus missing energy. In addition, we implement constraints arising from scalar top quark pair-production. We also study the production of a single top in association with missing energy and calculate the sensitivity of the LHC to the top quark hadronic and semi-leptonic decay modes with the current $20$ fb...

  4. MODAL TEST AND ANALYSIS OF CANTILEVER BEAM WITH TIP MASS

    Institute of Scientific and Technical Information of China (English)

    肖世富; 杜强; 陈滨; 刘才山; 向荣山; 周为华; 徐友钜; 徐有刚

    2002-01-01

    The phenomenon of dynamic stiffening is a research field of general interest for flexible multi-body systems. In fact, there are not only dynamic stiffening but also dynamic softening phenomenon in the flexible multi-body systems. In this paper, a non-linear dynamic model and its linearization characteristic equations of a cantilever beam with tip mass in the centrifugal field are established by adopting the general Hamilton Variational Principle. Then, the problems of the dynamic stiffening and the dynamic softening are studied by using numerical simulations. Meanwhile,the modal test is carried out on our centrifuge. The numerical results show that the system stiffness will be strengthened when the centrifugal tension force acts on the beam (i.e. the dynamic stiffening). However, the system stiffness will be weakened when the centrifugal compression force acts on the beam (i.e. the dynamic softening).Furthermore, the equilibrium position of the system will lose its stability when the inertial force reaches a critical value. Through theoretical analysis, we find that this phenomenon comes from the effect of dynamic softening resulting from the centrifugal compression force. Our test results verify the above conclusions and confirm that both dynamic stiffening and softening phenomena exist in flexible multi-body systems.

  5. 46 CFR 57.01-1 - Qualifications and production tests.

    Science.gov (United States)

    2010-10-01

    ... production tests for all types of manual and machine arc and gas welding and brazing processes. (b) (Modifies... 46 Shipping 2 2010-10-01 2010-10-01 false Qualifications and production tests. 57.01-1 Section 57... BRAZING Scope § 57.01-1 Qualifications and production tests. (a) (Replaces QW 101 and QB 101.)...

  6. A new torsion pendulum for testing the limits of free-fall for LISA test masses

    Science.gov (United States)

    Cavalleri, A.; Ciani, G.; Dolesi, R.; Heptonstall, A.; Hueller, M.; Nicolodi, D.; Rowan, S.; Tombolato, D.; Vitale, S.; Wass, P. J.; Weber, W. J.

    2009-05-01

    On-ground verification of the precision with which a test mass can be in perfect free-fall, without any stray forces, is among the most challenging aspects of preparing for LISA and LISA Pathfinder. This study aims at improving the sensitivity in torsion pendulum measurements of the stray forces arising in the interaction between a test mass and the capacitive position sensor that surrounds it. Measurements are performed with pendulum suspensions based on both tungsten and higher quality factor uncoated fused silica torsion fibers. The results achieved with the fused silica pendulum establish more stringent upper limits on the excess force noise attributable to the sensor—at a level that roughly coincides with the LISA Pathfinder flight goal around 1 mHz. Additionally, these measurements demonstrate a force sensitivity improvement over what can be achieved with thermal noise-limited tungsten over a wide range of frequencies, with significant further improvements still possible.

  7. Product Sterility Testing . . . To Test or Not to Test? That Is the Question.

    Science.gov (United States)

    Daniell, Elaine; Bryans, Trabue; Darnell, Kimbrell; Hansen, Joyce; Hitchins, Victoria M; Saavedra, Manuel

    2016-04-02

    The applications for sterility testing in the validation and routine control of sterilization of medical devices have changed dramatically over the years. As the definition of sterility assurance has evolved, so has the state of the science associated with product sterility testing. Historically, product sterility testing has been applied to such things as sterilization validation, sterilization lot release, packaging qualification, aseptic processing qualification, and determination of shelf life for the packaged medical device. In most of these cases, however, the results obtained from performing sterility testing on products do not provide the desired confirmation and assurance. Utilizing sterility testing on fully processed finished product is not appropriate for determination of sterilization process effectiveness, sterility assurance level, package integrity, or shelf life. The industry has developed more robust methods for validation of these applications to assure sterility and package performance. This article outlines the appropriate applications for sterility testing and highlight the applications currently in use that have significant limitations within the results and introduce undesirable risk to the validity of the data.

  8. W boson production and mass at the Tevatron

    Energy Technology Data Exchange (ETDEWEB)

    Stelzer-Chilton, Oliver; /Toronto U.

    2005-06-01

    The CDF and D0 collaborations have analyzed up to {approx} 200 pb{sup -1} of Run 2 physics data to measure W production properties such as the W cross section, the W width, lepton universality and the W charge asymmetry. From the cross section measurements, CDF obtains a lepton universality of g{sub {mu}}/g{sub e} = 0.998 {+-} 0.012 and g{sub {tau}}/g{sub e} = 0.99 {+-} 0.04 and an indirect W width of {Lambda}{sub W} = 2079 {+-} 41 MeV. D0 measured the W width directly and finds {Lambda}{sub W} = 2011 {+-} 142 MeV. CDF has estimated the uncertainties on the W boson mass measurements in the electron and muon decay channels and obtains an overall uncertainty of 76 MeV.

  9. W Boson Production and Mass at the Tevatron

    CERN Document Server

    Stelzer-Chilton, O; Abolins, M; Acharya, B S; Adams, M; Adams, T; Agelou, M; Agram, J L; Ahn, S H; Ahsan, M; Alexeev, G D; Alkhazov, G; Alton, A; Alverson, G; Alves, G A; Anastasoaie, M; Andeen, T; Anderson, S; Andrieu, B; Arnoud, Y; Askew, A; Åsman, B; Assis-Jesus, A C S; Atramentov, O; Autermann, C; Avila, C; Badaud, F; Baden, A; Baldin, B Yu; Balm, P W; Banerjee, S; Barberis, E; Bargassa, P; Baringer, P; Barnes, C; Barreto, J; Bartlett, J F; Bassler, U; Bauer, D; Bean, A; Beauceron, S; Begel, M; Bellavance, A; Beri, S B; Bernardi, G; Bernhard, R; Bertram, I; Besançon, M; Beuselinck, R; Bezzubov, V A; Bhat, P C; Bhatnagar, V; Binder, M; Biscarat, C; Black, K M; Blackler, I; Blazey, G; Blekman, F; Blessing, S; Bloch, D; Blumenschein, U; Böhnlein, A; Boeriu, O; Bolton, T A; Borcherding, F; Borissov, G; Bos, K; Bose, T; Brandt, A; Brock, R; Brooijmans, G; Bross, A; Buchanan, N J; Buchholz, D; Bühler, M; Büscher, V; Burdin, S; Burnett, T H; Busato, E; Butler, J M; Bystrický, J; Caron, S; Carvalho, W; Casey, B C K; Cason, N M; Castilla-Valdez, H; Chakrabarti, S; Chakraborty, D; Chan, K M; Chandra, A; Chapin, D; Charles, F; Cheu, E; Cho, D K; Choi, S; Choudhary, B; Christiansen, T; Christofek, L; Claes, D; Clement, B; Clément, C; Coadou, Y; Cooke, M; Cooper, W E; Coppage, D; Corcoran, M; Cothenet, A; Cousinou, M C; Cox, B; Crepe-Renaudin, S; Cristetiu, M; Cutts, D; Da Motta, H; Davies, B; Davies, G; Davis, G A; De, K; de Jong, P; De Jong, S J; De La Cruz-Burelo, E; De Oliveira Martins, C; Dean, S; Degenhardt, J D; Déliot, F; Demarteau, M; Demina, R; Demine, P; Denisov, D; Denisov, S P; Desai, S; Diehl, H T; Diesburg, M; Doidge, M; Dong, H; Doulas, S; Dudko, L V; Duflot, L; Dugad, S R; Duperrin, A; Dyer, J; Dyshkant, A; Eads, M; Edmunds, D; Edwards, T; Ellison, J; Elmsheuser, J; Elvira, V D; Eno, S; Ermolov, P; Eroshin, O V; Estrada, J; Evans, D; Evans, H; Evdokimov, A; Evdokimov, V N; Fast, J; Fatakia, S N; Feligioni, L; Ferbel, T; Fiedler, F; Filthaut, F; Fisher, W; Fisk, H E; Fleck, I; Fortner, M; Fox, H; Fu, S; Fuess, S; Gadfort, T; Galea, C F; Gallas, E; Galyaev, E; García, C; García-Bellido, A; Gardner, J; Gavrilov, V; Gay, P; Gelé, D; Gelhaus, R; Genser, K; Gerber, C E; Gershtein, Yu; Ginther, G; Golling, T; Gómez, B; Gounder, K; Goussiou, A; Grannis, P D; Greder, S; Greenlee, H; Greenwood, Z D; Gregores, E M; Gris, P; Grivaz, J F; Groer, L; Grünendahl, S; Grünewald, M W; Gurzhev, S N; Gutíerrez, G; Gutíerrez, P; Haas, A; Hadley, N J; Hagopian, S; Hall, I; Hall, R E; Han, C; Han, L; Hanagaki, K; Harder, K; Harrington, R; Hauptman, J M; Hauser, R; Hays, J; Hebbeker, T; Hedin, D; Heinmiller, J M; Heinson, A P; Heintz, U; Hensel, C; Hesketh, G; Hildreth, M D; Hirosky, R; Hobbs, J D; Hoeneisen, B; Hohlfeld, M; Hong, S J; Hooper, R; Houben, P; Hu, Y; Huang, J; Iashvili, I; Illingworth, R; Ito, A S; Jabeen, S; Jaffré, M; Jain, S; Jain, V; Jakobs, K; Jenkins, A; Jesik, R; Johns, K; Johnson, M; Jonckheere, A; Jonsson, P; Juste, A; Käfer, D; Kahl, W; Kahn, S; Kajfasz, E; Kalinin, A M; Kalk, J; Karmanov, D; Kasper, J; Kau, D; Kaur, R; Kehoe, R; Kermiche, S; Kesisoglou, S; Khanov, A; Kharchilava, A I; Kharzheev, Yu M; Kim, H; Klima, B; Klute, M; Kohli, J M; Kopal, M; Korablev, V M; Kotcher, J; Kothari, B; Koubarovsky, A; Kozelov, A V; Kozminski, J; Kryemadhi, A; Krzywdzinski, S; Kuleshov, S; Kulik, Y; Kumar, A; Kunori, S; Kupco, A; Kurca, T; Kvita, J; Lager, S; Lahrichi, N; Landsberg, G L; Lazoflores, J; Le Bihan, A C; Lebrun, P; Lee, W M; Leflat, A; Lehner, F; Leonidopoulos, C; Lévêque, J; Lewis, P; Li, J; Li, Q Z; Lima, J G R; Lincoln, D; Linn, S L; Linnemann, J T; Lipaev, V V; Lipton, R; Lobo, L; Lobodenko, A; Lokajícek, M; Lounis, A; Love, P; Lubatti, H J; Lueking, L; Lynker, M; Lyon, A L; Maciel, A K A; Madaras, R J; Mättig, P; Magass, C; Magerkurth, A; Magnan, A M; Makovec, N; Mal, P K; Malbouisson, H B; Malik, S; Malyshev, V L; Mao, H S; Maravin, Y; Martens, M; Mattingly, S E K; Mayorov, A A; McCarthy, R; McCroskey, R; Meder, D; Melanson, H L; Melnitchouk, A S; Mendes, A; Merkin, M; Merritt, K W; Meyer, A; Michaut, M; Miettinen, H; Mitrevski, J; Mokhov, N V; Molina, J; Mondal, N K; Moore, R W; Muanza, G S; Mulders, M; Mutaf, Y D; Nagy, E; Narain, M; Naumann, N A; Neal, H A; Negret, J P; Nelson, S; Neustroev, P; Nöding, C; Nomerotski, A; Novaes, S F; Nunnemann, T; Nurse, E; O'Dell, V; O'Neil, D C; Oguri, V; Oliveira, N; Oshima, N; Oteroy-Garzon, G J; Padley, P; Parashar, N; Park, S K; Parsons, J; Partridge, R; Parua, N; Patwa, A; Perea, P M; Pérez, E; Petroff, P; Petteni, M; Phaf, L; Piegaia, R; Pleier, M A; Podesta-Lerma, P L M; Podstavkov, V M; Pogorelov, Y; Pope, B G; Prado da Silva, W L; Prosper, H B; Protopopescu, S D; Qian, J; Quadt, A; Quinn, B; Rani, K J; Ranjan, K; Rapidis, P A; Ratoff, P N; Reay, N W; Reucroft, S; Rijssenbeek, M; Ripp-Baudot, I; Rizatdinova, F K; Rodrigues, R F; Royon, C; Rubinov, P; Ruchti, R; Rud, V I; Sajot, G; Sánchez-Hernández, A; Sanders, M P; Santoro, A F S; Savage, G; Sawyer, L; Scanlon, T; Schaile, A D; Schamberger, R D; Schellman, H; Schieferdecker, P; Schmitt, C; Schwartzman, A; Schwienhorst, R; Sen-Gupta, S; Severini, H; Shabalina, E; Shamim, M; Shary, V; Shchukin, A A; Shephard, W D; Shivpuri, R K; Shpakov, D; Sidwell, R A; Simák, V; Sirotenko, V I; Skubic, P L; Slattery, P F; Smith, R P; Smolek, K; Snow, G R; Snow, J; Snyder, S; Söldner-Rembold, S; Song, X; Sonnenschein, L; Sopczak, A; Sosebee, M; Soustruznik, K; Souza, M; Spurlock, B; Stanton, N R; Stark, J; Steele, J; Stevenson, K; Stolin, V; Stone, A; Stoyanova, D A; Strandberg, J; Strang, M A; Strauss, M; Ströhmer, R; Strom, D; Strovink, M; Stutte, L; Sumowidagdo, S; Sznajder, A; Talby, M; Tamburello, P; Taylor, W; Telford, P; Temple, J; Thomas, E; Thooris, B; Abazov, V M; Tomoto, M; Toole, T; Torborg, J; Towers, S; Trefzger, T; Trincaz-Duvoid, S; Tuchming, B; Tully, C; Turcot, A S; Tuts, P M; Uvarov, L; Uvarov, S; Uzunyan, S; Vachon, B; Van Kooten, R; Van Leeuwen, W M; Varelas, N; Varnes, E W; Vartapetian, A H; Vasilyev, I A; Vaupel, M; Verdier, P; Vertogradov, L S; Verzocchi, M; Villeneuve-Séguier, F; Vlimant, J R; Von Törne, E; Vreeswijk, M; Vu-Anh, T; Wahl, H D; Walker, R; Wang, L; Wang, Z M; Warchol, J; Watts, G; Wayne, M; Weber, M; Weerts, H; Wegner, M; Wermes, N; White, A; White, V; Wicke, D; Wijngaarden, D A; Wilson, G W; Wimpenny, S J; Wittlin, J; Wobisch, M; Womersley, J; Wood, D R; Wyatt, T R; Xu, Q; Xuan, N; Yacoob, S Y; Yamada, R; Yan, M; Yasuda, T; Yatsunenko, Y A; Yen, Y; Yip, K; Yoo, H D; Youn, S W; Yu, J; Yurkewicz, A; Zabi, A; Zatserklyaniy, A; Zdrazil, M; Zeitnitz, C; Zhang, D; Zhang, X; Zhao, T; Zhao, Z; Zhou, B; Zhu, J; Zielinski, M; Zieminska, D; Zieminski, A; Zitoun, R; Zutshi, V; Zverev, E G; Stelzer-Chilton, Oliver

    2005-01-01

    The CDF and D0 collaborations have analyzed up to ~200/pb of Run 2 physics data to measure W production properties such as the W cross section, the W width, lepton universality and the W charge asymmetry. From the cross section measurements, CDF obtains a lepton universality of g_mu/g_e = 0.998+-0.012 and g_tau/g_e = 0.99+-0.04 and an indirect W width of Gamma_W = 2079+-41 MeV. D0 measured the W width directly and finds Gamma_W = 2011+-142 MeV. CDF has estimated the uncertainties on the W boson mass measurements in the electron and muon decay channels and obtains an overall uncertainty of 76 MeV.

  10. 49 CFR 178.33b-8 - Production tests.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Production tests. 178.33b-8 Section 178.33b-8... Specifications for Inside Containers, and Linings § 178.33b-8 Production tests. (a) Burst Testing. (1) One out of... if the test container shall fail, the lot shall be rejected or ten additional containers may...

  11. MORPHOLOGICAL CHARACTERIZATION AND MASS PRODUCTION OF NEMATOPHAGOUS FUNGUS NEMATOCTONUS ROBUSTUS

    Directory of Open Access Journals (Sweden)

    Ramesh babu S,

    2014-06-01

    Full Text Available The plant parasitic nematodes infect the root tissues of the plant causing root galls that lead to reduced water and mineral uptake in the plant root system. Nematophagous fungus are used as biocontrol for the nematodes. Among those Nematoctonus are one of the species used as bioagent. Nematoctonus species produces an extensive mycelium and capture many nematodes with hour glass shaped adhesive knobs on the hyphae. Nematodes become attached to these adhesive knobs and the cuticle of nematode is penetrated by the infective hyphae. This isolate of Nematoctonus robustus is characterized by hyaline mycelium, dikaryotic in nature containing genetically two different nuclei in each cell, having distinct clamp connection. The fungus has better colonizing ability on natural solid substrates like wheat straw and rice straw. It also show good ability to colonize on different cereal grains and various other waste products like coconut coir and FYM etc. This species is one of the best used for mass production and effective for control of plant parasitic nematodes.

  12. Toxicity Tests Applied to the Biocidal Products

    OpenAIRE

    Karabay Yavaşoğlu, N.Ülkü

    2015-01-01

    Biocides are defined as chemical substances used to suppress, destroy, deter, render harmless, or exert a controlling effect on any harmful organism to human or animal health, or that cause damage to natural or manufactured materials. Biocidal products (BPs) containing biocides are disinfectants, products related to human and veterinary hygiene, products used for pests such as insects, rodents etc., repellents and industrial chemicals like anti-fouling paints for ship and material preservativ...

  13. Testing Gaugino Mass Unification Directly at the LHC

    CERN Document Server

    Nelson, Brent D

    2010-01-01

    We report on the first step of a systematic study of how gaugino mass unification can be probed at the LHC in a quasi-model independent manner. Here we focus our attention on the theoretically well-motivated mirage pattern of gaugino masses, a one-parameter family of models of which universal (high scale) gaugino masses are a limiting case. Using a statistical method to optimize our signature selection we arrive at three ensembles of observables targeted at the physics of the gaugino sector, allowing for a determination of this non-universality parameter without reconstructing individual mass eigenvalues or the soft supersymmetry-breaking gaugino masses themselves. In this controlled environment we find that approximately 80% of the supersymmetric parameter space would give rise to a model for which our method will detect non-universality in the gaugino mass sector at the 10% level with approximately 10 inverse femptobarns of integrated luminosity.

  14. Testing Gaugino Mass Unification Directly at the LHC

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Brent D. [Department of Physics, Northeastern University, Boston, Massachusetts (United States)

    2010-03-15

    We report on the first step of a systematic study of how gaugino mass unification can be probed at the CERN LHC in a quasi-model independent manner. Here we focus our attention on the theoretically well-motivated mirage pattern of gaugino masses, a one-parameter family of models of which universal (high scale) gaugino masses are a limiting case. Using a statistical method to optimize our signature selection we arrive at three ensembles of observables targeted at the physics of the gaugino sector, allowing for a determination of this non-universality parameter without reconstructing individual mass eigenvalues or the soft supersymmetry-breaking gaugino masses themselves. In this controlled environment we find that approximately 80% of the supersymmetric parameter space would give rise to a model for which our method will detect non-universality in the gaugino mass sector at the 10% level with O(10fb{sup -1}) of integrated luminosity.

  15. High Throughput, Continuous, Mass Production of Photovoltaic Modules

    Energy Technology Data Exchange (ETDEWEB)

    Kurt Barth

    2008-02-06

    AVA Solar has developed a very low cost solar photovoltaic (PV) manufacturing process and has demonstrated the significant economic and commercial potential of this technology. This I & I Category 3 project provided significant assistance toward accomplishing these milestones. The original goals of this project were to design, construct and test a production prototype system, fabricate PV modules and test the module performance. The original module manufacturing costs in the proposal were estimated at $2/Watt. The objectives of this project have been exceeded. An advanced processing line was designed, fabricated and installed. Using this automated, high throughput system, high efficiency devices and fully encapsulated modules were manufactured. AVA Solar has obtained 2 rounds of private equity funding, expand to 50 people and initiated the development of a large scale factory for 100+ megawatts of annual production. Modules will be manufactured at an industry leading cost which will enable AVA Solar's modules to produce power that is cost-competitive with traditional energy resources. With low manufacturing costs and the ability to scale manufacturing, AVA Solar has been contacted by some of the largest customers in the PV industry to negotiate long-term supply contracts. The current market for PV has continued to grow at 40%+ per year for nearly a decade and is projected to reach $40-$60 Billion by 2012. Currently, a crystalline silicon raw material supply shortage is limiting growth and raising costs. Our process does not use silicon, eliminating these limitations.

  16. Relevance of microbial finished product testing in food safety management

    NARCIS (Netherlands)

    Zwietering, M.H.; Jacxsens, L.; Membre, J.M.; Nauta, M.; Peterz, M.

    2016-01-01

    Management of microbiological food safety is largely based on good design of processes, products and procedures. Finished product testing may be considered as a control measure at the end of the production process. However, testing gives only very limited information on the safety status of a food.

  17. Relevance of microbial finished product testing in food safety management

    NARCIS (Netherlands)

    Zwietering, M.H.; Jacxsens, L.; Membre, J.M.; Nauta, M.; Peterz, M.

    2016-01-01

    Management of microbiological food safety is largely based on good design of processes, products and procedures. Finished product testing may be considered as a control measure at the end of the production process. However, testing gives only very limited information on the safety status of a food.

  18. Vacuum packaging technology for mass production of uncooled IRFPAs

    Science.gov (United States)

    Ito, Takuya; Tokuda, Takayuki; Kimata, Masafumi; Abe, Hideyuki; Tokashiki, Naotaka

    2009-05-01

    We developed vacuum packaging equipment and low-cost vacuum packaging technology for the mass production of uncooled IRFPAs. The equipment consists of two chambers with identical construction. Two-chamber architecture provides flexibility in the vacuum packaging process, so we can bake the components and achieve getter activation by heating, stem/cap soldering, and cap/window soldering in a series under high-vacuum conditions. Heaters and component-holding jigs are made of graphite to assure rapid and uniform heating to 500°C. The batch size is 27 if we choose a 15-mm diameter TO8 package and can be increased by enlarging the graphite heater area. We also developed a micro-vacuum gauge to evaluate the vacuum level in encapsulated packages. The operation principle of this vacuum gauge is based on thermal conduction by air molecules. It can be integrated in IRFPA chips since the fabrication process is compatible with that for IRFPAs. We encapsulated the vacuum gauges in TO8 packages with our vacuum packaging equipment, and confirmed that the pressure in fabricated packages is sufficiently low for high performance IRFPA operation (<< 1 Pa) with the micro-vacuum gauges.

  19. Mass production of CNTs using CVD multi-quartz tubes

    Energy Technology Data Exchange (ETDEWEB)

    Yousef, Samy; Mohamed, Alaa [Dept. of Production Engineering and Printing Technology, Akhbar Elyom Academy, Giza (Egypt)

    2016-11-15

    Carbon nanotubes (CNTs) have become the backbone of modern industries, including lightweight and heavy-duty industrial applications. Chemical vapor deposition (CVD) is considered as the most common method used to synthesize high yield CNTs. This work aims to develop the traditional CVD for the mass production of more economical CNTs, meeting the growing CNT demands among consumers by increasing the number of three particular reactors. All reactors housing is connected by small channels to provide the heat exchange possibility between the chambers, thereby decreasing synthesis time and reducing heat losses inside the ceramic body of the furnace. The novel design is simple and cheap with a lower reacting time and heat loss compared with the traditional CVD design. Methane, hydrogen, argon, and catalyzed iron nanoparticles were used as a carbon source and catalyst during the synthesis process. In addition, CNTs were produced using only a single quartz tube for comparison. The produced samples were examined using XRD, TEM, SEM, FTIR, and TGA. The results showed that the yield of CNTs increases by 287 % compared with those synthesized with a single quartz tube. Moreover, the total synthesis time of CNTs decreases by 37 % because of decreased heat leakage.

  20. Mass transport-related stratal disruption and sedimentary products

    Science.gov (United States)

    Ogata, Kei; Mutti, Emiliano; Tinterri, Roberto

    2010-05-01

    From an outcrop perspective, mass transport deposit are commonly represented by "chaotic" units, characterized by dismembered and internally deformed slide blocks of different sizes and shapes, embedded in a more or less abundant fine-grained matrix. The large amount of data derived from geophysical investigations of modern continental margins have permitted the characterization of the overall geometry of many of these deposits, which, however, remain still relatively poorly described from outcrop studies of collisional basins. Results of this work show that in mass-transport deposits an unsorted, strongly mixed, relatively fine-grained clastic matrix almost invariably occurs in irregularly interconnected patches and pseudo-veins, infilling space between large clasts and blocks. We interpreted the aspect of this matrix as typical of a liquefied mixture of water and sediment, characterized by an extremely high mobility due to overpressured conditions, as evidenced by both lateral and vertical injections. On a much larger scale this kind of matrix is probably represented by the seismically "transparent" facies separating slide blocks of many mass-transport deposits observed in seismic-reflection profiles. The inferred mechanism of matrix production suggests a progressive soft-sediment deformation, linked to different phases of submarine landslide evolution (i.e. triggering, translation, accumulation and post-depositional stages), leading to an almost complete stratal disruption within the chaotic units. From our data we suggest that most submarine landslides move because of the development of ductile shear zones marked by the presence of "overpressured" matrix, both internally and along the basal surface. The matrix acts as a lubricating medium, accommodating friction forces and deformation, thus permitting the differential movement of discrete internal portions and enhancing the submarine slide mobility. Based on our experience, we suggest that this kind of deposit

  1. Status of the LHC Superconducting Cable Mass Production

    CERN Document Server

    Adam, J D; Cavallari, Giorgio; Charifoulline, Z; Denarié, C H; Le Naour, S; Leroy, D F; Oberli, L R; Richter, D; Verweij, A P; Wolf, R

    2002-01-01

    Six contracts have been placed with industrial companies for the production of 1200 tons of the superconducting (SC) cables needed for the main dipoles and quadrupoles of the Large Hadron Collider (LHC). In addition, two contracts have been placed for the supply of 470 tons of NbTi and 26 tons of Nb sheets. The main characteristic of the specification is that it is functional. This means that the physical, mechanical and electrical properties of strands and cables are specified without defining the manufacturing processes. Facilities for the high precision measurements of the wire and cable properties have been implemented at CERN, such as strand and cable critical current, copper to superconductor ratio, interstrand resistance, magnetisation, RRR at 4.2 K and 1.9 K. The production has started showing that the highly demanding specifications can be fulfilled. This paper reviews the organisation of the contracts, the test facilities installed at CERN, the various types of measurements and the results of the ma...

  2. Product Offerings Testing through Customer Satisfaction

    Directory of Open Access Journals (Sweden)

    Tina Vukasovic

    2014-09-01

    Full Text Available Consumer satisfaction is imperative to a successful business, the reason for the choice of topic for this paper being explained thereby. Market changes have resulted in consumer’s enormous growth of power, which was recognized by many companies who adapted their business to meeting those expectations. Adaptation, however, also resulted in the need for constant measuring and evaluation. According to the above-mentioned, this paper measures consumer satisfaction with the product offer of the drugstore chain X The survey results have shown that X’s offer has not completely come up to the expectations of a smaller number of interviewees. In relation to the measuring ranks of consumer satisfaction defined, the greatest number of consumers has turned out to be satisfied with the product offer, whereas the percentage of those who find it excellent is smaller than the percentage of those who assess it as average.

  3. Product acceptance environmental and destructive testing for reliability.

    Energy Technology Data Exchange (ETDEWEB)

    Dvorack, Michael A.; Kerschen, Thomas J.; Collins, Elmer W.

    2007-08-01

    To determine whether a component is meeting its reliability requirement during production, acceptance sampling is employed in which selected units coming off the production line are subjected to additional environmental and/or destructive tests that are within the normal environment space to which the component is expected to be exposed throughout its life in the Stockpile. This report describes what these tests are and how they are scored for reliability purposes. The roles of screens, Engineering Use Only tests, and next assembly product acceptance testing are also discussed, along with both the advantages and disadvantages of environmental and destructive testing.

  4. Mass production of volume phase holographic gratings for the VIRUS spectrograph array

    Science.gov (United States)

    Chonis, Taylor S.; Frantz, Amy; Hill, Gary J.; Clemens, J. Christopher; Lee, Hanshin; Tuttle, Sarah E.; Adams, Joshua J.; Marshall, J. L.; DePoy, D. L.; Prochaska, Travis

    2014-07-01

    The Visible Integral-field Replicable Unit Spectrograph (VIRUS) is a baseline array of 150 copies of a simple, fiber-fed integral field spectrograph that will be deployed on the Hobby-Eberly Telescope (HET). VIRUS is the first optical astronomical instrument to be replicated on an industrial scale, and represents a relatively inexpensive solution for carrying out large-area spectroscopic surveys, such as the HET Dark Energy Experiment (HETDEX). Each spectrograph contains a volume phase holographic (VPH) grating with a 138 mm diameter clear aperture as its dispersing element. The instrument utilizes the grating in first-order for 350 VPH gratings has been mass produced for VIRUS. Here, we present the design of the VIRUS VPH gratings and a discussion of their mass production. We additionally present the design and functionality of a custom apparatus that has been used to rapidly test the first-order diffraction efficiency of the gratings for various discrete wavelengths within the VIRUS spectral range. This device has been used to perform both in-situ tests to monitor the effects of adjustments to the production prescription as well as to carry out the final acceptance tests of the gratings' diffraction efficiency. Finally, we present the as-built performance results for the entire suite of VPH gratings.

  5. Mass-rearing of Mediterranean fruit fly using low-cost yeast products produced in Brazil

    Directory of Open Access Journals (Sweden)

    Alberto Moreira da Silva Neto

    2012-12-01

    Full Text Available Ceratitis capitata is one of the most important pests of fruits for exportation, and Sterile Insect Technique (SIT has been the most efficient and environmental friendly technique used to control fruit fly populations around the world. A key goal in achieving a successful SIT program is a mass rearing system producing high quality insects at low cost. Providing adults with an artificial diet containing hydrolysed protein has been the major obstacle for bio-production facilities in Brazil, because it is expensive and has to be imported. Two other commercial products, autolysed yeast (AY and yeast extract (YE, of domestic origin and low cost, were tested as substitutes of the imported hydrolyzed protein. To compare their efficiency we observed the female fecundity, adult survival and egg viability of flies raised on diets containing one of each of the different protein products. Flies reared on the domestic yeast products had equivalent or superior performance to the flies reared on imported protein. Both AY and YE can be a possible substitute for imported hydrolyzed protein for C. capitata mass-rearing, as they are cheaper and are readily available in the national market.

  6. Large-scale inhomogeneity in sapphire test masses revealed by Rayleigh scattering imaging

    Science.gov (United States)

    Yan, Zewu; Ju, Li; Eon, François; Gras, Slawomir; Zhao, Chunnong; Jacob, John; Blair, David G.

    2004-03-01

    Rayleigh scattering in test masses can introduce noise and reduce the sensitivity of laser interferometric gravitational wave detectors. In this paper, we present laser Rayleigh scattering imaging as a technique to investigate sapphire test masses. The system provides three-dimensional Rayleigh scattering mapping of entire test masses and quantitative evaluation of the Rayleigh scattering coefficient. Rayleigh scattering mapping of two sapphire samples reveals point defects as well as inhomogeneous structures in the samples. We present results showing significant non-uniform scattering within two 4.5 kg sapphire test masses manufactured by the heat exchanger method.

  7. 46 CFR 160.021-4 - Approval and production tests.

    Science.gov (United States)

    2010-10-01

    ... manufacturer. A new lot must be started with: (i) Any change in construction details, (ii) any change in sources of raw materials, or (iii) the start of production on a new production line or on a previously... (specimen) must be tested as follows: (i) Conditioning of test specimens—water resistance. Immerse specimen...

  8. Methodological issues in testing the marginal productivity theory

    NARCIS (Netherlands)

    P.T. Gottschalk (Peter); J. Tinbergen (Jan)

    1982-01-01

    textabstractPrevious tests of the marginal productivity theory have been criticized on several grounds reviewed by the authors. One important deficiency has been the small number of factor inputs entered in the production functions. In 1978 Gottschalk suggested a method to estimate production functi

  9. Relevance of microbial finished product testing in food safety management

    DEFF Research Database (Denmark)

    Zwietering, Marcel H.; Jacxsens, Liesbeth; Membré, Jeanne Marie

    2016-01-01

    -active way by implementing an effective food safety management system. For verification activities in a food safety management system, finished product testing may however be useful. For three cases studies; canned food, chocolate and cooked ham, the relevance of testing both of finished products...... and the production environment is discussed. Since the level of control of different processes can be largely different it is beneficial if the frequency of sampling of finished products and production environments would be related to the associated human health risk, which can be assessed on the basis of risk...

  10. Dust Production and Mass Loss in Cool Evolved Stars

    Science.gov (United States)

    Boyer, M. L.

    2013-01-01

    Following the red giant branch phase and the subsequent core He-burning phase, the low- to intermediate-mass stars (0.8star. I will briefly review the current status of models that include AGB mass loss and relate them to recent observations of AGB stars from the Surveying the Agents of Galaxy Evolution (SAGE) Spitzer surveys of the Small and Large Magellanic Clouds, including measures of the total dust input to the interstellar medium from AGB stars.

  11. Testing multi-mass dynamical models of star clusters with real data: mass segregation in three Galactic globular clusters

    CERN Document Server

    Sollima, A; Beccari, G; Pallanca, C

    2016-01-01

    We present the results of the analysis of deep photometric data for a sample of three Galactic globular clusters (NGC5466, NGC6218 and NGC6981) with the aim of estimating their degree of mass segregation and testing the predictions of analytic dynamical models. The adopted dataset, composed by both Hubble Space Telescope and ground based data, reaches the low-mass end of the mass functions of these clusters from the center up to their tidal radii allowing to derive their radial distribution of stars with different masses. All the analysed clusters show evidence of mass segregation with the most massive stars more concentrated than low-mass ones. The structures of NGC5466 and NGC6981 are well reproduced by multimass dynamical models adopting a lowered-Maxwellian distribution function and the prescription for mass segregation given by Gunn & Griffin (1979). Instead, NGC6218 appears to be more mass segregated than model predictions. By applying the same technique to mock observations derived from snapshots s...

  12. MICROSCOPE - fabricating test masses for an in-orbit test of the equivalence principle

    Energy Technology Data Exchange (ETDEWEB)

    Hagedorn, Daniel; Heyne, Heinz-Peter; Metschke, Stephan; Langner, Uwe; Gruener, Sven; Loeffler, Frank [Physikalisch-Technische Bundesanstalt (PTB), Braunschweig (Germany); Lebat, Vincent; Rodrigues, Manuel [Office National d' Etudes et de Recherches Aerospatiales (ONERA), Chatillon (France); Touboul, Pierre [ONERA, Chemin de la Huniere, Palaiseau (France)

    2013-09-15

    The MICROSCOPE space mission is to test in 2016 the Weak Equivalence Principle (WEP) with an accuracy of 10{sup -15}. This fundamental physics mission should provide answers to the basic question of the universality of free-falling bodies in a uniform gravity field. During 18 months, the mission should improve the current ground experiments by at least two orders of magnitude. The payload is composed of two electrostatic differential space accelerometers that exhibit a resolution of 2 x 10{sup -12} m s{sup -2} Hz{sup -1/2}. By measuring the difference of acceleration between two concentric test masses at the orbital frequency, a possible WEP violation signal is extracted from the measurement where the gravity gradient effect dominates by a factor of one hundred. This paper addresses the scientific objective of the space mission and describes how the performance drives the specification. A particular focus is made on the work jointly performed by ONERA and PTB to fulfil the fabricating requirements. (copyright 2013 by WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  13. Adopting Product Modularity in House Building to Support Mass Customisation

    Directory of Open Access Journals (Sweden)

    Cecília G. da Rocha

    2015-04-01

    Full Text Available Product modularity is a concept that can contribute to the improvement of product quality and production efficiency in house-building. However, there is a lack of consensus in the literature on the concepts that define product modularity. Furthermore, little attention has been given to the differences between building construction and manufacturing, for which product modularity was originally developed. This research aims to address that gap by adapting the conceptualization of product modularity so that it can effectively be used in the house-building industry. The methodological approach adopted in this study was Design Science Research, and two empirical studies were carried out on construction companies based in Brazil and in the U.K. Those studies are used to illustrate the applicability and utility of the proposed concepts and tools. Research findings indicate that the adoption of product modularity concepts results in benefits to both traditional construction technologies and pre-fabricated building systems.

  14. [Determination of residual glycol ethers in leather and leather products by gas chromatography/mass spectrometry].

    Science.gov (United States)

    Wang, Ghengyun; Zhang, Weiya; Li, Lixia; Shen, Yalei; Lin, Junfeng; Xie, Tangtang; Chu, Naiqing

    2014-08-01

    An effective method was established for the simultaneous determination of residual glycol ethers in leather and leather products by gas chromatography/mass spectrometry. Glycol ethers in leather and leather products were ultrasonically extracted at 45 °C, using ethyl acetate as the extraction solvent. The extracts were purified by solid phase extraction (SPE) columns, and then analyzed by gas chromatography/mass spectrometry in selected ion monitoring mode. The content of each analyte was calibrated by external standard method. The limit of detection of ethylene glycol ethyl ether (EGEE) was 0. 10 mg/kg under the condition of signal to noise (S/N) of 3 and the limits of the other 11 glycol ethers were all less than 0.05 mg/kg. The spiked recoveries varied from 81. 2% to 95. 5% at three different spiked levels with the relative standard deviations (RSDs) ranged from 1.4% to 6. 6%. The proposed method is simple, rapid and accurate, with the limits of detection much less than the requirements of the Regulation Concerning Registration, Evaluation, Authorization and Restriction of Chemicals (REACH) of European Union. It is applicable to the determination of residual glycol ethers in leather and leather products, and provides a reference for the relevant testing standards.

  15. Production and Resource Scheduling in Mass Customization with Dependent Setup Consideration

    DEFF Research Database (Denmark)

    Nielsen, Izabela Ewa; Bocewicz, G.; Do, Ngoc Anh Dung

    2014-01-01

    Mass customization has been implemented in services and manufactures to increase the competitiveness of companies. In a manufacturing company, the procedure for production and resource scheduling has to be changed to adapt to mass customization. A good production and resource scheduling will cont...

  16. Simultaneous determination of cosmetics ingredients in nail products by fast gas chromatography with tandem mass spectrometry.

    Science.gov (United States)

    Zhou, Wanlong; Wang, Perry G; Wittenberg, James B; Rua, Diego; Krynitsky, Alexander J

    2016-05-13

    A rapid and sensitive gas chromatography with tandem mass spectrometry (GC-MS/MS) method has been developed and validated to quantitatively determine cosmetic ingredients, such as toluene, N-methylpyrrolidone, 2,4-dihydroxybenzophenone (benzophenone-1, BP-1), and diethylene glycol dimethacrylate, in nail products. In this procedure, test portions were extracted with acetone, followed by vortexing, sonication, centrifugation, and filtration. During the extraction procedure, BP-1 was derivatized making it amenable to GC-MS analysis, using N,O-​bis(trimethylsilyl)​trifluoroacetamide. The four ingredients were quantified by GC-MS/MS in an electron ionization mode. Four corresponding stable isotopically labeled analogues were selected as internal standards, which were added at the beginning of the sample preparation to correct for recoveries and matrix effects. The validated method was used to screen 34 commercial nail products for these four cosmetic ingredients. The most common ingredients detected in the nail products were toluene and BP-1. Toluene was detected in 26 products and ranged from 1.36 to 173,000μg/g. BP-1 ranged from 18.3 to 2,370μg/g in 10 products. Published by Elsevier B.V.

  17. Correlation Results for a Mass Loaded Vehicle Panel Test Article Finite Element Models and Modal Survey Tests

    Science.gov (United States)

    Maasha, Rumaasha; Towner, Robert L.

    2012-01-01

    High-fidelity Finite Element Models (FEMs) were developed to support a recent test program at Marshall Space Flight Center (MSFC). The FEMs correspond to test articles used for a series of acoustic tests. Modal survey tests were used to validate the FEMs for five acoustic tests (a bare panel and four different mass-loaded panel configurations). An additional modal survey test was performed on the empty test fixture (orthogrid panel mounting fixture, between the reverb and anechoic chambers). Modal survey tests were used to test-validate the dynamic characteristics of FEMs used for acoustic test excitation. Modal survey testing and subsequent model correlation has validated the natural frequencies and mode shapes of the FEMs. The modal survey test results provide a basis for the analysis models used for acoustic loading response test and analysis comparisons

  18. Mass production of genetically modified Aedes aegypti for field releases in Brazil.

    Science.gov (United States)

    Carvalho, Danilo O; Nimmo, Derric; Naish, Neil; McKemey, Andrew R; Gray, Pam; Wilke, André B B; Marrelli, Mauro T; Virginio, Jair F; Alphey, Luke; Capurro, Margareth L

    2014-01-04

    New techniques and methods are being sought to try to win the battle against mosquitoes. Recent advances in molecular techniques have led to the development of new and innovative methods of mosquito control based around the Sterile Insect Technique (SIT)(1-3). A control method known as RIDL (Release of Insects carrying a Dominant Lethal)(4), is based around SIT, but uses genetic methods to remove the need for radiation-sterilization(5-8). A RIDL strain of Ae. aegypti was successfully tested in the field in Grand Cayman(9,10); further field use is planned or in progress in other countries around the world. Mass rearing of insects has been established in several insect species and to levels of billions a week. However, in mosquitoes, rearing has generally been performed on a much smaller scale, with most large scale rearing being performed in the 1970s and 80s. For a RIDL program it is desirable to release as few females as possible as they bite and transmit disease. In a mass rearing program there are several stages to produce the males to be released: egg production, rearing eggs until pupation, and then sorting males from females before release. These males are then used for a RIDL control program, released as either pupae or adults(11,12). To suppress a mosquito population using RIDL a large number of high quality male adults need to be reared(13,14). The following describes the methods for the mass rearing of OX513A, a RIDL strain of Ae. aegypti (8), for release and covers the techniques required for the production of eggs and mass rearing RIDL males for a control program.

  19. Design stage confirmation of lifetime improvement for newly modified products through accelerated life testing

    Energy Technology Data Exchange (ETDEWEB)

    Mohammadian, S. Hossein, E-mail: seyed-h.mohammadian.1@ulaval.c [Centre Interuniversitaire de Recherche sur les Reseaux d' Entreprise, la Logistique et le Transport (CIRRELT), Departement de Genie Mecanique, Pavillon Adrien-Pouliot, Universite Laval, Quebec, G1V 0A6 (Canada) and Centre Interdisciplinaire de Recherche en Readaptation et en Integration Sociale (CIRRIS), Institut de Readaptation en Deficience Physique de Quebec, 525 Boul. Hamel, Quebec, G1M 2S8 (Canada); Ait-Kadi, Daoud, E-mail: Daoud.Aitkadi@gmc.ulaval.c [Centre Interuniversitaire de Recherche sur les Reseaux d' Entreprise, la Logistique et le Transport (CIRRELT), Departement de Genie Mecanique, Pavillon Adrien-Pouliot, Universite Laval, Quebec, G1V 0A6 (Canada); Centre Interdisciplinaire de Recherche en Readaptation et en Integration Sociale (CIRRIS), Institut de Readaptation en Deficience Physique de Quebec, 525 Boul. Hamel, Quebec, G1M 2S8 (Canada)

    2010-08-15

    After a modification to the original version of a product and before mass production, the expected improvement in the product lifetime or reliability needs to be validated. This paper presents three approaches based on accelerated life testing to verify, estimate and confirm the lifetime or reliability of a newly modified product at design stage: ALT comparative approach, reliability estimation approach, and reliability validation test. Test samples of the original and modified versions are expected to fail during the tests in order to obtain their failure time data. In ALT comparative approach, the statistical comparison between failure time data of the original and modified versions is used to verify the required improvement in lifetime. In reliability estimation approach, the relationship made between available lifetime and failure time data of the original version is used to extrapolate lifetime data of the modified version from its failure time data. Since modified versions are usually highly reliable, all test samples might survive the tests (without any failures) that results in the lack of failure time data for statistical analysis. To confirm a level of service reliability with confidence, reliability validation test is presented to make an estimate of the number of samples required to survive the tests. To fulfill the same level of confidence for fewer number of prototypes (as test samples), the test time must be extended. On the other hand, more prototypes are needed to pass a shorter test time if there are any time constraints.

  20. Altered primary production during mass-extinction events

    NARCIS (Netherlands)

    van de Schootbrugge, B.; Gollner, S.

    2013-01-01

    The Big Five mass-extinction events are characterized by dramatic changes in primary producers. Initial disturbance to primary producers is usually followed by a succession of pioneers that represent qualitative and quantitative changes in standing crops of land plants and/or phytoplankton. On land,

  1. Testing catalysts for production performance and runaway limits

    Energy Technology Data Exchange (ETDEWEB)

    Berty, I.J.; Berty, J.M.; Brinkeroff, P.T.; Chovan, T. (Berty Reaction Engineers, Ltd., Akron, OH (US))

    1989-11-01

    The results of laboratory catalyst tests, conducted in recycle reactors under fixed conditions of feed rate and composition and otherwise at average production conditions, permit the evaluation of catalyst performance for production reactors. These tests are performed in short steady-state runs at stepwise increasing temperatures until a specified product concentration is reached. From these results, in addition to performance evaluation, the thermal stability criteria of the reaction can also be calculated. This information is needed to maximize production within the thermal runaway limit. Since the thermal runaway limit, estimated from the catalyst test, does not contain assumptions on kinetics, the experimentally evaluated runaway limit can be used as a benchmark to help discriminate between kinetic models that were developed from other data sets. The evaluation of the performance as well as the thermal runaway limit is shown on actual experimental measurements made for the production of ethylene oxide by oxidation of ethylene.

  2. Hanford Apatite Treatability Test Report Errata: Apatite Mass Loading Calculation

    Energy Technology Data Exchange (ETDEWEB)

    Szecsody, James E.; Vermeul, Vincent R.; Williams, Mark D.; Truex, Michael J.

    2014-05-19

    The objective of this errata report is to document an error in the apatite loading (i.e., treatment capacity) estimate reported in previous apatite treatability test reports and provide additional calculation details for estimating apatite loading and barrier longevity. The apatite treatability test final report (PNNL-19572; Vermeul et al. 2010) documents the results of the first field-scale evaluation of the injectable apatite PRB technology. The apatite loading value in units of milligram-apatite per gram-sediment is incorrect in this and some other previous reports. The apatite loading in units of milligram phosphate per gram-sediment, however, is correct, and this is the unit used for comparison to field core sample measurements.

  3. Variation of mass in primordial nucleosynthesis as a test of induced matter brane gravity

    Energy Technology Data Exchange (ETDEWEB)

    Jalalzadeh, S. [Department of Physics, Shahid Beheshti University, Evin, Tehran 19839 (Iran, Islamic Republic of)], E-mail: s-jalalzadeh@sbu.ac.ir; Yazdani, A.M. [Department of Physics, Qom branch, Islamic Azad University, Qom (Iran, Islamic Republic of); West University of Timisoara, V. Parvan Ave. 4, RO-300223, Timisoara (Romania)], E-mail: yazdani@quantum.physics.uvt.ro

    2008-06-26

    The variation of mass in induced matter theory using Ceroch-Stewart-Walter perturbations of submanifolds is redefined. It is shown that the deviation of primordial Helium production due to a variation on the difference between the 'rest' mass of the nucleus is in agreement with induced matter brane gravity.

  4. Empirical testing of forecast update procedure forseasonal products

    DEFF Research Database (Denmark)

    Wong, Chee Yew; Johansen, John

    2008-01-01

    of a toy supply chain. The theoretical simulation involves historical weekly consumer demand data for 122 toy products. The empirical test is then carried out in real-time with 291 toy products. The results show that the proposed forecast updating procedure: 1) reduced forecast errors of the annual...

  5. Mercury mass flow in iron and steel production process and its implications for mercury emission control.

    Science.gov (United States)

    Wang, Fengyang; Wang, Shuxiao; Zhang, Lei; Yang, Hai; Gao, Wei; Wu, Qingru; Hao, Jiming

    2016-05-01

    The iron and steel production process is one of the predominant anthropogenic sources of atmospheric mercury emissions worldwide. In this study, field tests were conducted to study mercury emission characteristics and mass flows at two iron and steel plants in China. It was found that low-sulfur flue gas from sintering machines could contribute up to 41% of the total atmospheric mercury emissions, and desulfurization devices could remarkably help reduce the emissions. Coal gas burning accounted for 17%-49% of the total mercury emissions, and therefore the mercury control of coal gas burning, specifically for the power plant burning coal gas to generate electricity, was significantly important. The emissions from limestone and dolomite production and electric furnaces can contribute 29.3% and 4.2% of the total mercury emissions from iron and steel production. More attention should be paid to mercury emissions from these two processes. Blast furnace dust accounted for 27%-36% of the total mercury output for the whole iron and steel production process. The recycling of blast furnace dust could greatly increase the atmospheric mercury emissions and should not be conducted. The mercury emission factors for the coke oven, sintering machine and blast furnace were 0.039-0.047gHg/ton steel, and for the electric furnace it was 0.021gHg/ton steel. The predominant emission species was oxidized mercury, accounting for 59%-73% of total mercury emissions to air.

  6. Simple and rapid analysis of methyldibromo glutaronitrile in cosmetic products by gas chromatography mass spectrometry.

    Science.gov (United States)

    Pellegrini, Manuela; Bossù, Elena; Rotolo, Maria Concetta; Pacifici, Roberta; Pichini, Simona

    2011-12-15

    A simple and rapid gas chromatography (GC) method with mass spectrometry (MS) detection has been developed for the determination of methyldibromo glutaronitrile (MDBGN) in cosmetic products. The presence of this preservative in commercial cosmetic samples is prohibited since 2007 because of its allergenic properties. The analyzed products were opportunely diluted in methanol and MDBGN was separated by fused silica capillary column and detected by electron impact (EI)-MS in positive ionization mode with a total run time of 7 min. The assay was validated in the range 0.005-0.100 mg MDBGN per g of examined product with good determination coefficients (r(2)≥0.99) for the calibration curves. At three concentrations spanning the linear dynamic range of the calibration curves, mean recoveries were always higher than 95% for MDBGN in the tested cosmetics. This method was successfully applied to the analysis of cleansing gels, shampoo and solar waters to disclose the eventual presence of MDBGN illegally added in cosmetic products. Copyright © 2011 Elsevier B.V. All rights reserved.

  7. Mass Customisation and Highly Individualised Solutions. Stretching Mass Customisation Beyond the Traditional Paradigm of Industrial Production

    DEFF Research Database (Denmark)

    Morelli, Nicola; Nielsen, Louise Møller

    2007-01-01

    Globalisation if creating large changes in our social and economic system, whereas demand patterns are becoming more and more diversified and highly localised. The difference between global production and local demand relates to a paradigmatic shift in the way of looking at production and consump...

  8. 46 CFR 160.024-4 - Approval and production tests.

    Science.gov (United States)

    2010-10-01

    ... be numbered serially by the manufacturer. A new lot must be started with: (i) Any change in construction details, (ii) any change in sources of raw materials, or (iii) the start of production on a new... tested as follows: (i) Conditioning of test specimens—water resistance. Immerse specimen horizontally...

  9. Food Production Worker. Dietetic Support Personnel Achievement Test.

    Science.gov (United States)

    Oklahoma State Dept. of Vocational and Technical Education, Stillwater.

    This guide contains a series of multiple-choice items and guidelines to assist instructors in composing criterion-referenced tests for use in the food production worker component of Oklahoma's Dietetic Support Personnel training program. Test items addressing each of the following occupational duty areas are provided: human relations; hygiene and…

  10. Medium mass fragments production due to momentum dependent interactions

    CERN Document Server

    Kumar, Sanjeev; Puri, Rajeev K; 10.1103/PhysRevC.78.064602

    2010-01-01

    The role of system size and momentum dependent effects are analyzed in multifragmenation by simulating symmetric reactions of Ca+Ca, Ni+Ni, Nb+Nb, Xe+Xe, Er+Er, Au+Au, and U+U at incident energies between 50 MeV/nucleon and 1000 MeV/nucleon and over full impact parameter zones. Our detailed study reveals that there exist a system size dependence when reaction is simulated with momentum dependent interactions. This dependence exhibits a mass power law behavior.

  11. Tracer mass recovery in fractured aquifers estimated from multiple well tests.

    Science.gov (United States)

    Sanford, William E; Cook, Peter G; Robinson, Neville I; Weatherill, Douglas

    2006-01-01

    Forced-gradient tracer tests in fractured aquifers often report low mass recoveries. In fractured aquifers, fractures intersected by one borehole may not be intersected by another. As a result (1) injected tracer can follow pathways away from the withdrawal well causing low mass recovery and (2) recovered water can follow pathways not connected to the injection well causing significant tracer dilution. These two effects occur along with other forms of apparent mass loss. If the strength of the connection between wells and the amount of dilution can be predicted ahead of time, tracer tests can be designed to optimize mass recovery and dilution. A technique is developed to use hydraulic tests in fractured aquifers to calculate the conductance (strength of connection) between well pairs and to predict mass recovery and amount of dilution during forced gradient tracer tests. Flow is considered to take place through conduits, which connect the wells to each other and to distant sources or sinks. Mass recovery is related to the proportion of flow leaving the injection well and arriving at the withdrawal well, and dilution is related to the proportion of the flow from the withdrawal well that is derived from the injection well. The technique can be used to choose well pairs for tracer tests, what injection and withdrawal rates to use, and which direction to establish the hydraulic gradient to maximize mass recovery and/or minimize dilution. The method is applied to several tracer tests in fractured aquifers in the Clare Valley, South Australia.

  12. Intermediate mass black holes in AGN disks: I. Production & Growth

    CERN Document Server

    McKernan, B; Lyra, W; Perets, H B

    2012-01-01

    Here we propose a mechanism for efficiently growing intermediate mass black holes (IMBH) in disks around supermassive black holes. Stellar mass objects can efficiently agglomerate when facilitated by the gas disk. Stars, compact objects and binaries can migrate, accrete and merge within disks around supermassive black holes. While dynamical heating by cusp stars excites the velocity dispersion of nuclear cluster objects (NCOs) in the disk, gas in the disk damps NCO orbits. If gas damping dominates, NCOs remain in the disk with circularized orbits and large collision cross-sections. IMBH seeds can grow extremely rapidly by collisions with disk NCOs at low relative velocities, allowing for super-Eddington growth rates. Once an IMBH seed has cleared out its feeding zone of disk NCOs, growth of IMBH seeds can become dominated by gas accretion from the AGN disk. However, the IMBH can migrate in the disk and expand its feeding zone, permitting a super-Eddington accretion rate to continue. Growth of IMBH seeds via N...

  13. Protocol for testing bioremediation products against weathered Alaskan crude oil

    Energy Technology Data Exchange (ETDEWEB)

    Venosa, A.D.; Haines, J.R.; Nisamaneepong, W.; Govind, R.; Pradhan, S.

    1990-01-01

    In the summer of 1989, EPA and Exxon Corp. conducted a joint field study to determine if natural biodegradation of the Prudoe Bay crude oil spilled from the Exxon Valdez could be accelerated by application of oleophilic and water soluble fertilizers. Numerous private firms have since submitted proposals to have their microbial products tested for bioremediation enhancement. EPA commissioned the National Environmental Technology Applications Corporation (NETAC) to coordinate an effort to select and test commercial products for efficacy against Alaskan crude oil. A panel of experts was assembled to review the proposals, and nine products were selected for the first tier of testing. The experiments were conducted at the Risk Reduction Engineering Laboratory in Cincinnati. Three lines of evidence were used to select the final products for further testing: cumalative oxygen uptake via electrolytic respirometry, microbial growth, and compositional analysis of treated oil by GC and GC/MS. The commercial products were compared against oleophilic and inorganic fertilizers in a comprehensive protocol incorporating sterile and non-sterile controls. Respirometric vessels and shaker flask microcosms were set up for the comparative testing using weathered oil and natural seawater from Prince William Sound. The paper presents the protocol, the test results, and conclusions derived from the study.

  14. A Listening Test of Contro11ed-Productive Ability

    Institute of Scientific and Technical Information of China (English)

    马静

    2001-01-01

    The purpose of the study is to estimate a new testing method of evaluating the student's ability of Listening Comprehension. The problem to be addressed is whether there is evidence to show that the method can discriminate between the testees, separating the above average students from the average and the below-average studentsThus, the controlled-productive listening test will be" found to be reliable, valid (in that the test distinguished between different proficiency students )and practical.

  15. Development and Production of a Leishmania Skin Test

    Science.gov (United States)

    2009-03-01

    manufacturing process of Leishmania tropica Skin Test Antigen (LtSTA) was made during this contract period to increase the yield and robustness of the...interest group. 15. SUBJECT TERMS LtSTA = Leishmania tropica Skin Test Antigen 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT... tropica Skin Test Antigen (LtSTA), is a sterile injectable microfluidized lysate of Leishmania tropica (WR#1063:C1A) promastigotes. The product is heat

  16. Antimycobacterial susceptibility testing methods for natural products research

    Directory of Open Access Journals (Sweden)

    Juan Gabriel Bueno Sánchez

    2010-06-01

    Full Text Available The emergence of multidrug-resistant strains of Mycobacterium tuberculosis underscores the need of continuous developments on new and efficient methods to determine the susceptibility of isolates of M. tuberculosis in the search for novel antimicrobial agents. Natural products constitute an important source of new drugs, but design and implementation of antimycobacterial susceptibility testing methods are necessary for evaluate the different extracts and compounds. A number of biological assay methodologies are in current use, ranging from the classical disk diffusion and broth dilution assay format, to radiorespirometric (BACTEC, dye-based, and fluorescent/luminescence reporter assays. This review presents an analysis on the in vitro susceptibility testing methods developed for determinate antitubercular activity in natural products and related compounds (semi-synthetic natural products and natural products-derived compounds and the criteria to select the adequate method for determination of biological activity of new natural products.

  17. Multiphoton production and tests of QED at LEP-II

    CERN Document Server

    Winter, M

    2001-01-01

    Data collected by the 4 LEP collaborations from 1995 to 2000 at collision energies ranging from 130 to 208 GeV were used to measure the cross-section of the process e/sup +/e/sup -/ to gamma gamma ( gamma ). QED predictions for this reaction were tested with a few per-cent accuracy and manifestations of physics beyond the standard model (SM) were investigated. Preliminary lower bounds on the cut-off parameter Lambda /sub +or-/, the mass of an excited electron, the string mass scale underlying low-scale quantum gravity and on energy scales expressing various contact interactions were derived.

  18. Central location test vs. home use test: Contrasting results depending on product type

    NARCIS (Netherlands)

    Boutrolle, I.; Delarue, J.; Arranz, D.; Rogeaux, M.; Köster, E.P.

    2007-01-01

    Marketing professionals and sensory scientists have several hedonic testing methods at their disposal to assess product acceptability. The central location test (CLT) which usually takes place in a standardised location under controlled conditions is more frequently used than the home use test (HUT)

  19. Test Sample for the Spatially Resolved Quantification of Illicit Drugs on Fingerprints Using Imaging Mass Spectrometry

    NARCIS (Netherlands)

    Muramoto, S.; Forbes, T.P.; van Asten, A.C.; Gillen, G.

    2015-01-01

    A novel test sample for the spatially resolved quantification of illicit drugs on the surface of a fingerprint using time-of-flight secondary ion mass spectrometry (ToF-SIMS) and desorption electrospray ionization mass spectrometry (DESI-MS) was demonstrated. Calibration curves relating the signal

  20. Test Sample for the Spatially Resolved Quantification of Illicit Drugs on Fingerprints Using Imaging Mass Spectrometry

    NARCIS (Netherlands)

    Muramoto, S.; Forbes, T.P.; van Asten, A.C.; Gillen, G.

    2015-01-01

    A novel test sample for the spatially resolved quantification of illicit drugs on the surface of a fingerprint using time-of-flight secondary ion mass spectrometry (ToF-SIMS) and desorption electrospray ionization mass spectrometry (DESI-MS) was demonstrated. Calibration curves relating the signal i

  1. Statistics of mass production. Technical report, January 1, 1992--March 15, 1992

    Energy Technology Data Exchange (ETDEWEB)

    Williams, R.L.; Gateley, W.Y. [Kaman Sciences Corp., Colorado Springs, CO (United States)

    1993-05-01

    Statistical Quality Control (SQC) is a broad term defining procedures that can be employed during production to insure that parts are produced having specified characteristics and performance. In developing complex systems of systems whose performance cannot be tested as entities, methods exist to identify components and subsystems whose failures, degradations, and variations most severely erect system level performance. Once identified, two methods may be employed to reduce or eliminate the system effects caused by such critical components - (1) design change employing such techniques as redundancy, proliferation, and spatial separation, and (2) component quality improvement. This paper summarizes the SQC methods and procedures that can be employed in mass producing electronic parts - ICs, SRAMs, buffers, capacitors, connectors - to reduce variability and insure performance to specified radiation, current, voltage, temperature, shock, and vibration levels. Producing such quality parts reduces uncertainties in performance and will aid materially in validating the survivability of components, subsystems, and systems to specified threats.

  2. Development of mass-production technique of the ATLAS thin gap chamber in Japan

    CERN Document Server

    Tanaka, S; Ishii, K; Iwasaki, H; Arataki, Y; Bando, T; Homma, Y; Ishino, M; Kondo, T; Kobayashi, T; Kurashige, H; Mikenberg, G; Miyazaki, Y; Nakagawa, Y; Nanjo, H; Ikeno, M; Nozaki, M; Ochi, A; Sasaki, O; Shoa, M; Sugimoto, T; Takeda, H; Takeshita, T; Yokoyama, C

    2004-01-01

    The thin gap chambers (TGCs) are used for the muon trigger system in the end-cap regions of the ATLAS detector. As the anode-cathode distance is small, 1.4 mm, chamber flatness is essential to achieve a uniform gas gain over the chamber. The TGC mass production phase at High Energy Accelerator Research Organization (KEK) started in January 2001. In order to perform a stable production with high quality we developed a chamber closing system. When we glue two half- chambers together, we sandwich them with a granite table and an aluminum honeycomb panel that keep the chamber flat from both sides. By using silk screens, we also control the quantity of epoxy adhesive that affects the chamber thickness. Owing to these developments, we can achieve the flatness of less than 100 mu m. Uniformity of detection efficiency of the TGC is measured with a cosmic-ray test bench at Kobe University. We have tested 300 TGCs so far. Position dependence of the efficiency is measured with a granularity of 5 mm- by-5 mm. The average...

  3. Techniques developed for the ATLAS Thin Gap Chambers mass production in Japan

    CERN Document Server

    Tanaka, S; Ishii, K; Iwasaki, H; Arataki, Y; Bando, T; Homma, Y; Ishino, M; Kondo, T; Kobayashi, T; Kurashige, H; Mikenberg, G; Miyazaki, Y; Nakagawa, Y; Nanjo, H; Ikeno, M; Nozaki, M; Ochi, A; Sasaki, O; Shoa, M; Sugimoto, T; Takeda, H; Takeshita, T; Yokoyama, C

    2004-01-01

    The Thin Gap Chambers (TGCs) are used for the muon trigger system in the end-cap regions of the ATLAS detector. The TGC mass production phase at High Energy Accelerator Research Organization (KEK) started in January 2001. As the anode-cathode distance is small, 1.4 mm, chamber flatness is essential to achieve a uniform gas gain over the chamber. In order to perform a stable production with high quality we developed a chamber closing system. When we glue two half-chambers together, we sandwich them between a granite table and an aluminum honeycomb panel to keep the chamber flat from both sides. By using silk screens, we control the quantity of epoxy adhesive that affects the chamber thickness. Due to these developments, we can achieve the flatness of less than 100 µm. Uniformity of detection efficiency of the TGC is measured with a cosmic-ray test bench at Kobe University. So far we have tested 300 TGCs. Position dependence of the efficiency is measured with a granularity of 5mm-by-5mm. The average efficiency...

  4. Mass extrapolation of the amplitude for pion production in N-N collision

    Energy Technology Data Exchange (ETDEWEB)

    Afnan, I.R.; Thomas, A.W.

    1977-06-01

    The S-wave pion production process (at q/sub ..pi../ = 0) is calculated as a function of the mass of the produced pion. The invariant matrix element is found to be surprisingly constant over a large range of pion mass.

  5. Authentication of Fish Products by Large-Scale Comparison of Tandem Mass Spectra

    DEFF Research Database (Denmark)

    Wulff, Tune; Nielsen, Michael Engelbrecht; Deelder, André M.

    2013-01-01

    a new robust, proteome-wide tandem mass spectrometry method for species recognition and food product authentication. The method does not use or require any genome sequences or selection of tandem mass spectra but uses all acquired data. The experimental steps were performed in a simple, standardized...

  6. STRUCTURAL CHARACTERIZATION OF THE DECOMPOSITION PRODUCTS OF SALBUTAMOL BY LIQUID-CHROMATOGRAPHY IONSPRAY MASS-SPECTROMETRY

    NARCIS (Netherlands)

    MALKKILAINE, L; BRUINS, AP

    1994-01-01

    Liquid chromatography-ionspray mass spectrometry was used to elucidate the structures of the decomposition products of salbutamol. The best sensitivity in mass spectrometry was achieved by using a mixture of acetonitrile and ammonium formate (10 mM, pH 3.3) as the mobile phase in liquid chromatograp

  7. Performance of different fire retardant products applied on Norway spruce tested in a Cone calorimeter

    Directory of Open Access Journals (Sweden)

    Kögl Josef

    2013-11-01

    Full Text Available On the European market there are several fire retardant products available, which reach class B in the European classification system. The producers promise their fire retardants are effective in reducing different reaction to fire parameters of wood such as the time to ignition, the mass loss rate, the heat release rate, the total heat release, the charring rate and the flame spread. This paper discusses the performance of fire retardant products as pressure impregnated wood, non-intumescence surface coatings and intumescence coatings on Norway spruce (Picea abies. The investigations are performed by using a cone calo- rimeter test according to ISO 5660. The thermal exposures of the investigations are 50 kW/m2 and the standard IS0 834 test curve. As result information about the heat release rate, the mass loss rate and the total heat release for duration of 900 seconds will be presented in this paper.

  8. End-Cretaceous marine mass extinction not caused by productivity collapse

    OpenAIRE

    Alegret, Laia; Thomas, Ellen; Lohmann, Kyger C.

    2011-01-01

    An asteroid impact at the end of the Cretaceous caused mass extinction, but extinction mechanisms are not well-understood. The collapse of sea surface to sea floor carbon isotope gradients has been interpreted as reflecting a global collapse of primary productivity (Strangelove Ocean) or export productivity (Living Ocean), which caused mass extinction higher in the marine food chain. Phytoplankton-dependent benthic foraminifera on the deep-sea floor, however, did not suffer significant extinc...

  9. Preconceptual design of the new production reactor circulator test facility

    Energy Technology Data Exchange (ETDEWEB)

    Thurston, G.

    1990-06-01

    This report presents the results of a study of a new circulator test facility for the New Production Reactor Modular High-Temperature Gas-Cooled Reactor. The report addresses the preconceptual design of a stand-alone test facility with all the required equipment to test the Main Circulator/shutoff valve and Shutdown Cooling Circulator/shutoff valve. Each type of circulator will be tested in its own full flow, full power helium test loop. Testing will cover the entire operating range of each unit. The loop will include a test vessel, in which the circulator/valve will be mounted, and external piping. The external flow piping will include a throttle valve, flowmeter, and heat exchanger. Subsystems will include helium handling, helium purification, and cooling water. A computer-based data acquisition and control system will be provided. The estimated costs for the design and construction of this facility are included. 2 refs., 15 figs.

  10. Fission product plateout/liftoff/washoff test plan. Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    Acharya, R.; Hanson, D.

    1988-05-01

    A test program is planned in the COMEDIE loop of the Commissariat a l`Energy Atomique (CEA), Grenoble, France, to generate integral test data for the validation of computer codes used to predict fission product transport and core corrosion in the Modular High Temperature Gas-Cooled Reactor (MHTGR). The inpile testing will be performed by the CEA under contract from the US Department of Energy (DOE); the contract will be administered by Oak Ridge National Laboratory (ORNL). The primary purpose of this test plan is to provide an overview of the proposed program in terms of the overall scope and schedule. 8 refs, 3 figs.

  11. Submerged Culture of Phellinus linteus for Mass Production of Polysaccharides.

    Science.gov (United States)

    Lee, June Woo; Baek, Seong Jin; Kim, Yong Seok

    2008-09-01

    In order to increase the mycelial production of Phellinus linteus, which exhibits potent anticancer activity, some ingredients of the medium used to culture P. linteus were investigated. The optimal medium composition for the production of Phellinus linteus was determined to be as follows: fructose, 40 g/l; yeast extract, 20 g/l; K2HPO4, 0.46 g/l; KH2PO4, 1.00 g/l; MgSO4·7H2O, 0.50 g/l; FeCl2·62O, 0.01 g/l; MnCl2·4H2O, 0.036 g/l; ZnCl2, 0.03 g/l; and CuSO4·7H2O, 0.005 g/l. The optimal culture conditions were determined to be as follows: temperature, 28℃; initial pH, 5.5; aeration, 0.6 vvm; and agitation, 100 rpm, respectively. Under optimal composition and conditions, the maximum mycelial biomass achieved in a 5 l jar fermentor was 29.9 g/l.

  12. Helium mass flow measurement in the International Fusion Superconducting Magnet Test Facility

    Energy Technology Data Exchange (ETDEWEB)

    Baylor, L.R.

    1986-08-01

    The measurement of helium mass flow in the International Fusion Superconducting Magnet Test Facility (IFSMTF) is an important aspect in the operation of the facility's cryogenic system. Data interpretation methods that lead to inaccurate results can cause severe difficulty in controlling the experimental superconducting coils being tested in the facility. This technical memorandum documents the methods of helium mass flow measurement used in the IFSMTF for all participants of the Large Coil Program and for other cryogenic experimentalists needing information on mass flow measurements. Examples of experimental data taken and calculations made are included to illustrate the applicability of the methods used.

  13. Tandem Mass Spectrometry in Combination with Product Ion Mobility for the Identification of Phospholipids

    Energy Technology Data Exchange (ETDEWEB)

    Berry, Karin A. Zemski; Barkley, Robert M.; Berry, Joseph J.; Hankin, Joseph A.; Hoyes, Emmy; Brown, Jeffery M.; Murphy, Robert C.

    2017-01-03

    Concerted tandem and traveling wave ion mobility mass spectrometry (CTS analysis) is a unique method that results in a four-dimensional data set including nominal precursor ion mass, product ion mobility, accurate mass of product ion, and ion abundance. This nontargeted lipidomics CTS approach was applied in both positive- and negative-ion mode to phospholipids present in human serum, and the data set was used to evaluate the value of product ion mobility in identifying lipids in a complex mixture. It was determined that the combination of diagnostic product ions and unique collisional cross-section values of product ions is a powerful tool in the structural identification of lipids in a complex biological sample.

  14. Mass Production of Carbon Nanofibers Using Microwave Technology.

    Science.gov (United States)

    Mubarak, N M; Abdullah, E C; Sahu, J N; Jayakumar, N S; Ganesan, P

    2015-12-01

    Carbon nanotubes (CNFs) were produced by gas phase single stage microwave assisted chemical vapour deposition (MA-CVD) using ferrocene as a catalyst and acetylene (C2H2) and hydrogen (H2) as precursor gases. The effect of the process parameters such as microwave power, radiation time, and gas ratio of C2H2/H2 was investigated. The CNFs were characterized using scanning and transmission electron microscopy (TEM), and by thermogravimetric analysis (TGA). Results reveal that the optimized conditions for CNF production were 1000 W reaction power, 35 min radiation time, and 0.8 gas ratio of C2H2/H2. TEM analyses revealed that the uniformly dispersed CNFs diameters ranging from 115-131 nm. The TGA analysis showed that the purity of CNF produced was 93%.

  15. Alternatives to animal testing in the safety evaluation of products.

    Science.gov (United States)

    Knight, Derek J; Breheny, Damien

    2002-01-01

    The conventional method for assessing the safety of products, ranging from pharmaceuticals to agrochemicals, biocides and industrial and household chemicals - including cosmetics - involves determining their toxicological properties by using experimental animals. The aim is to identify any possible adverse effects in humans by using these animal models. Providing safe products is undoubtedly of the utmost importance but, over the last decade or so, this aim has come into conflict with strong public opinion, especially in Europe, against animal testing. Industry, academia and the regulators have worked in partnership to find other ways of evaluating the safety of products, by non-animal testing, or at least by reducing the numbers of animals required and the severity of the tests in which they are used. There is a long way to go before products can be evaluated without any animal studies, and it may be that this laudable aim is an impossible dream. Nevertheless, considerable progress has been made by using a combination of in vitro tests and the prediction of properties based on chemical structure. The aim of this review is to describe these important and worthwhile developments in various areas of toxicological testing, with a focus on the European regulatory framework for general industrial and household chemicals.

  16. THE PRODUCT CONSISTENCY TEST HOW AND WHY IT WAS DEVELOPED

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C; Ned Bibler, N

    2008-12-15

    The Product Consistency Test (PCT), American Society for Testing Materials (ASTM) Standard C1285, is currently used world wide for testing glass and glass-ceramic waste forms for high level waste (HLW), low level waste (LLW), and hazardous wastes. Development of the PCT was initiated in 1986 because HLW glass waste forms required extensive characterization before actual production began and required continued characterization during production ({ge}25 years). Non-radioactive startup was in 1994 and radioactive startup was in 1996. The PCT underwent extensive development from 1986-1994 and became an ASTM consensus standard in 1994. During the extensive laboratory testing and inter- and intra-laboratory round robins using non-radioactive and radioactive glasses, the PCT was shown to be very reproducible, to yield reliable results rapidly, to distinguish between glasses of different durability and homogeneity, and to easily be performed in shielded cell facilities with radioactive samples. In 1997, the scope was broadened to include hazardous and mixed (radioactive and hazardous) waste glasses. In 2002, the scope was broadened to include glass-ceramic waste forms which are currently being recommended for second generation nuclear wastes yet to be generated in the nuclear renaissance. Since the PCT has proven useful for glass-ceramics with up to 75% ceramic component and has been used to evaluate Pu ceramic waste forms, the use of this test for other ceramic/mineral waste forms such as geopolymers, hydroceramics, and fluidized bed steam reformer mineralized product is under investigation.

  17. Zirconium pressure tube testing: Test procedures, Production Assurance Program (Project H-700)

    Energy Technology Data Exchange (ETDEWEB)

    Zaloudek, F.R.; Lewis, M. [Pacific Northwest Lab., Richland, WA (United States)

    1986-06-01

    UNC Nuclear Industries (UNC) has initiated a plan for the fabrication of zirconium alloy pressure tubes required for the future operation of N-Reactor. As part of this plan, UNC is establishing a program to qualify and develop a process capable of fabricating these pressure tubes to the requirements of UNC specification HWS 6502, REV. 4, Amendment 1. The objective of the Pressure Tube Testing Task is to support the UNC program-by performing physical, mechanical and chemical testing on prototype tube sections produced during FY-1986, 1987 and 1988 and to test samples from production runs after 1988 as may be required. The types of tests included in the Zirconium Pressure Tube Testing Program will be as follows: tensile tests; burst tests; fracture toughness tests; corrosion tests; chemical composition analyses; grain structure evaluations. The purpose of this document is to define the procedures that will be used in each type of test included in this task.

  18. Mass production of volume phase holographic gratings for the VIRUS spectrograph array

    CERN Document Server

    Chonis, Taylor S; Hill, Gary J; Clemens, J Christopher; Lee, Hanshin; Tuttle, Sarah E; Adams, Joshua J; Marshall, J L; DePoy, D L; Prochaska, Travis

    2014-01-01

    The Visible Integral-field Replicable Unit Spectrograph (VIRUS) is a baseline array of 150 copies of a simple, fiber-fed integral field spectrograph that will be deployed on the Hobby-Eberly Telescope (HET). VIRUS is the first optical astronomical instrument to be replicated on an industrial scale, and represents a relatively inexpensive solution for carrying out large-area spectroscopic surveys, such as the HET Dark Energy Experiment (HETDEX). Each spectrograph contains a volume phase holographic (VPH) grating with a 138 mm diameter clear aperture as its dispersing element. The instrument utilizes the grating in first-order for 350-550 nm. Including witness samples, a suite of 170 VPH gratings has been mass produced for VIRUS. Here, we present the design of the VIRUS VPH gratings and a discussion of their mass production. We additionally present the design and functionality of a custom apparatus that has been used to rapidly test the first-order diffraction efficiency of the gratings for various discrete wav...

  19. Differential distributions for top-quark hadro-production with a running mass

    Energy Technology Data Exchange (ETDEWEB)

    Dowling, M. [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Moch, S. [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Hamburg Univ. (Germany). 2. Inst. fuer Theoretische Physik

    2013-05-15

    We take a look at how the differential distributions for top-quark production are affected by changing to the running mass scheme. Specifically we consider the transverse momentum, rapidity and pair-invariant mass distributions at NLO for the top-quark mass in the MS scheme. It is found that, similar to the total cross section, the perturbative expansion converges faster and the scale dependence improves using the mass in the MS scheme as opposed to the on-shell scheme. We also update the analysis for the total cross section using the now available full NNLO contribution.

  20. Smart Product Design and Production Control for Effective Mass Customization in the Industry 4.0 Concept

    Directory of Open Access Journals (Sweden)

    Zawadzki Przemysław

    2016-09-01

    Full Text Available The paper presents a general concept of smart design and production control as key elements for efficient operation of a smart factory. The authors present various techniques that aid the design process of individualized products and organization of their production in the context of realization of the mass customization strategy, which allows a shortened time of development for a new product. Particular attention was paid to integration of additive manufacturing technologies and virtual reality techniques, which are a base of the so-called hybrid prototyping.

  1. Ground testing and flight demonstration of charge management of insulated test masses using UV-LED electron photoemission

    Science.gov (United States)

    Saraf, Shailendhar; Buchman, Sasha; Balakrishnan, Karthik; Lui, Chin Yang; Soulage, Michael; Faied, Dohy; Hanson, John; Ling, Kuok; Jaroux, Belgacem; Suwaidan, Badr Al; AlRashed, Abdullah; Al-Nassban, Badr; Alaqeel, Faisal; Harbi, Mohammed Al; Salamah, Badr Bin; Othman, Mohammed Bin; Qasim, Bandar Bin; Alfauwaz, Abdulrahman; Al-Majed, Mohammed; DeBra, Daniel; Byer, Robert

    2016-12-01

    The UV-LED mission demonstrates the precise control of the potential of electrically isolated test masses. Test mass charge control is essential for the operation of space accelerometers and drag-free sensors which are at the core of geodesy, aeronomy and precision navigation missions as well as gravitational wave experiments and observatories. Charge management using photoelectrons generated by the 254 nm UV line of Hg was first demonstrated on Gravity Probe B and is presently part of the LISA Pathfinder technology demonstration. The UV-LED mission and prior ground testing demonstrates that AlGaN UVLEDs operating at 255 nm are superior to Hg lamps because of their smaller size, lower power draw, higher dynamic range, and higher control authority. We show laboratory data demonstrating the effectiveness and survivability of the UV-LED devices and performance of the charge management system. We also show flight data from a small satellite experiment that was one of the payloads on KACST’s SaudiSat-4 mission that demonstrates ‘AC charge control’ (UV-LEDs and bias are AC modulated with adjustable relative phase) between a spherical test mass and its housing. The result of the mission brings the UV-LED device Technology Readiness Level (TRL) to TRL-9 and the charge management system to TRL-7. We demonstrate the ability to control the test mass potential on an 89 mm diameter spherical test mass over a 20 mm gap in a drag-free system configuration, with potential measured using an ultra-high impedance contact probe. Finally, the key electrical and optical characteristics of the UV-LEDs showed less than 7.5% change in performance after 12 months in orbit.

  2. Productivity affects the density-body mass relationship of soil fauna communities

    NARCIS (Netherlands)

    Comor, V.N.R.; Thakur, M.P.; Berg, M.P.; Bie, de S.; Prins, H.H.T.; Langevelde, van F.

    2014-01-01

    The productivity of ecosystems and their disturbance regime affect the structure of animal communities. However, it is not clear which trophic levels benefit the most from higher productivity or are the most impacted by disturbance. The density-body mass (DBM) relationship has been shown to reflect

  3. Design, construction and testing of holographic PV concentrator modules and construction of a pilot plant for serial production of the holographic optical concentrator system on flexible foils. Follow-up project: Completion of the production process for mass production of large format holographic optical elements on flexible foils for solar technology. Final report; Auslegung, Konstruktion und Test von holographischen PV-Konzentratormodulen und Aufbau einer Pilotanlage zur Serienfertigung der holographischen Konzentratoroptik auf flexiblen Folien. Anschlussvorhaben: Vervollstaendigung der Produktionsverfahren fuer die Serienfertigung von grossformatigen holographischen optischen Elementen auf flexiblen Folien fuer die Solartechnik. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Stojanoff, C.G.; Froehlich, K.; Froening, P.; Schulat, J.; Schuette, H.; Wagemann, E.U.

    1997-06-30

    The aim of the research project is the development of a technique for value for money mass-production of large area holographic focussers made of dichromate gelatine for photo-electrics. The holograms act simultaneously as spectrally dispersing and focussing optical elements, which focus the sunlight in discrete bands on the spectrally matched solar cells. The three marked characteristics of the holographic focussers are the diffraction efficiency, the spectral bandwidth and the central working wavelength. The optimum values of these parameters depend on the variation of the layer thickness and the index of refraction over the aperture of the hologram, and on the ability of the DCG layer to provide great modulation of the index of refraction. Mass-production of large format holographic lenses (transmission holograms) and mirrors (reflection holograms) demands precise coating of the supporting substrate (glass or PET foil) with dichromate gelatine. Mass-production of the holographic lenses requires a matrix hologram with 50% diffraction efficiency and is done with two copier plants developed in the project. (orig./AKF) [Deutsch] Ziel des Forschungsvorhabens ist die Entwicklung einer Technologie fuer die preiswerte serielle Herstellung von grossflaechigen holographischen Konzentratoren in Dichromatgelatine fuer die Photovoltaik. Die Hologramme wirken gleichzeitig als spektral dispergierende und fokussierende optische Elemente, die das Sonnenlicht in diskreten Baendern auf spektral angepasste Solarzellen konzentrieren. Die drei kennzeichnenden Charakteristiken der holographischen Konzentratoren sind die Beugungseffizienz, die spektrale Bandbreite und die zentrale Arbeitswellenlaenge. Die optimalen Werte dieser Parameter sind durch die Variation der Schichtdicke und des Brechnungsindexes ueber die Apertur des Hologramms, sowie durch die Faehigkeit der DCG-Schicht grosse Brechungsindexmodulation zu ermoeglichen, eindeutig bedingt. Die serielle Fertigung der

  4. Estimating kinetic mass transfer by resting-period measurements in flow-interruption tracer tests.

    Science.gov (United States)

    Gong, R; Lu, C; Wu, W-M; Cheng, H; Gu, B; Watson, D B; Criddle, C S; Kitanidis, P K; Brooks, S C; Jardine, P M; Luo, J

    2010-09-20

    Flow-interruption tracer test is an effective approach to identify kinetic mass transfer processes for solute transport in subsurface media. By switching well pumping and resting, one may alter the dominant transport mechanism and generate special concentration patterns for identifying kinetic mass transfer processes. In the present research, we conducted three-phase (i.e., pumping, resting, and pumping) field-scale flow-interruption tracer tests using a conservative tracer bromide in a multiple-well system installed at the US Department of Energy Site, Oak Ridge, TN. A novel modeling approach based on the resting-period measurements was developed to estimate the mass transfer parameters. This approach completely relied on the measured breakthrough curves without requiring detailed aquifer characterization and solving transport equations in nonuniform, transient flow fields. Additional measurements, including hydraulic heads and tracer concentrations in large pumping wells, were taken to justify the assumption that mass transfer processes dominated concentration change during resting periods. The developed approach can be conveniently applied to any linear mass transfer model. Both first-order and multirate mass transfer models were applied to analyze the breakthrough curves at various monitoring wells. The multirate mass transfer model was capable of jointly fitting breakthrough curve behavior, showing the effectiveness and flexibility for incorporating aquifer heterogeneity and scale effects in upscaling effective mass transfer models.

  5. Paired comparison product testing when individual preferences are stochastic

    NARCIS (Netherlands)

    B. Wierenga (Berend)

    1974-01-01

    textabstractThe preference of an individual in a paired comparison product test is stochastic, i.e. the probability p, that he will prefer one of the two alternatives, is not 0 or 1, but lies somewhere between these values. It is shown that the distribution of p, when approximated by a beta distribu

  6. A semianalytic model for the productivity testing of multiple wells

    NARCIS (Netherlands)

    Fokker, P.A.; Verga, F.

    2008-01-01

    We present a semianalytic method for modeling the productivity testing of vertical, horizontal, slanted, or multilateral wells. The method is applicable to both oil and gas reservoirs and automatically accounts for well interference. The use of analytic expressions ensures that short-time transient

  7. Generic development of topical dermatologic products: formulation development, process development, and testing of topical dermatologic products.

    Science.gov (United States)

    Chang, Rong-Kun; Raw, Andre; Lionberger, Robert; Yu, Lawrence

    2013-01-01

    This review presents considerations which can be employed during the development of a semi-solid topical generic product. This includes a discussion on the implementation of quality by design concepts during development to ensure the generic drug product has similar desired quality attributes to the reference-listed drug (RLD) and ensure batch to batch consistency through commercial production. This encompasses the concept of reverse-engineering to copy the RLD as a strategy during product development to ensure qualitative (Q1) and quantitative (Q2) formulation similarity, as well as similarity in formulation microstructure (Q3). The concept of utilizing in vitro skin permeation studies as a tool to justify formulation differences between the test generic product and the RLD to ensure a successful pharmacodynamic or clinical endpoint bioequivalence study is discussed. The review concludes with a discussion on drug product evaluation and quality tests as well as in vivo bioequivalence studies.

  8. Production Facility Prototype Blower 1000 Hour Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Woloshun, Keith Albert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Dale, Gregory E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Romero, Frank Patrick [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Dalmas, Dale Allen [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-10-18

    The roots blower in use at ANL for in-beam experiments and also at LANL for flow tests was sized for 12 mm diameter disks and significantly less beam heating. Currently, the disks are 29 mm in diameter, with a 12 mm FWHM Gaussian beam spot at 42 MeV and 2.86 μA on each side of the target, 5.72 μA total. The target design itself is reported elsewhere. With the increased beam heating, the helium flow requirement increased so that a larger blower was need for a mass flow rate of 400 g/s at 2.76 MPa (400 psig). An Aerzen GM 12.4 blower was selected, and is now installed at the LANL facility for target and component flow testing. Two extended test of >1000 hr operation have been completed. Those results and discussion thereof are reported herein. Also included in Appendix A is the detailed description of the blower and its installation, while Appendix B documents the pressure vessel design analysis. The blower has been operated for 1000 hours as a preliminary investigation of long term performance, operation and possible maintenance issues. The blower performed well, with no significant change in blower head or mass flow rate developed under the operating conditions. Upon inspection, some oil had leaked out of the shaft seal of the blower. The shaft seal and bearing race have been replaced. Test results and conclusions are in Appendix B.

  9. Production Facility Prototype Blower 1000 Hour Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Woloshun, Keith Albert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Dale, Gregory E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Romero, Frank Patrick [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Dalmas, Dale Allen [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-10-18

    The roots blower in use at ANL for in-beam experiments and also at LANL for flow tests was sized for 12 mm diameter disks and significantly less beam heating. Currently, the disks are 29 mm in diameter, with a 12 mm FWHM Gaussian beam spot at 42 MeV and 2.86 μA on each side of the target, 5.72 μA total. The target design itself is reported elsewhere. With the increased beam heating, the helium flow requirement increased so that a larger blower was needed for a mass flow rate of 400 g/s at 2.76 MPa (400 psig). An Aerzen GM 12.4 blower was selected, and is now installed at the LANL facility for target and component flow testing. Two extended tests of >1000 hr operation have been completed. Those results and discussion thereof are reported herein. Also included in Appendix A is the detailed description of the blower and its installation, while Appendix B documents the pressure vessel design analysis. The blower has been operated for 1000 hours as a preliminary investigation of long-term performance, operation and possible maintenance issues. The blower performed well, with no significant change in blower head or mass flow rate developed under the operating conditions. Upon inspection, some oil had leaked out of the shaft seal of the blower. The shaft seal and bearing race have been replaced. Test results and conclusions are in Appendix B.

  10. First Experience in the Mass Production of Components for the LHC Dipoles

    CERN Document Server

    Fessia, P; Perini, D; Verbeeck, T

    2002-01-01

    This paper reports on the manufacturing features and difficulties experienced for the preliminary mass production of the main mechanical components of the dipole cold mass. The production of about 600 km of superconducting coil copper wedges, 5'000 coil layer jump spacers and boxes, 12'500'000 austenitic steel collars and 5'800'000 low-carbon yoke laminations is spread over 4 European countries and involves 6 manufactory firms. The general technical requirements for the manufacturing process as well as the imposed production checks and quality controls are reviewed. An overview of the preliminary results is presented with an outlook towards the analysis and statistical which are in a process to be implemented for the follow-up of the mass production.

  11. Intermediate mass dilepton production during the chemical equilibration of quark gluon plasma

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The production of dileptons from the chemically equilibrating quark gluon plasma in the intermediate mass region has been studied. Comparing with the calculated results based on the thermodynamic equilibrium system of quark gluon plasma, it has been found that the quark phase of the chemically equilibrating system gives rise to an even larger enhancement of the dileptons production. Therefore, such an enhancement of dilepton production may signal the formation of quark gluon plasma.

  12. The development of a modified composition of ceramic mass for the production of bricks

    Science.gov (United States)

    Torosyan, V. F.; Torosyan, E. S.; Yakutova, V. A.; Antyufeev, V. K.

    2016-04-01

    The need to improve the technical level of production of construction materials, their product range, to improve product quality and reduce its cost requires the expansion of the raw material base, the use of resource and energy saving technology and design solutions. To implement all these it is necessary to conduct a more detailed study of the properties of ceramic materials and to investigate the behavior-modifying components of their formulations. This paper presents the development of the composition of ceramic mass for the production of bricks, a modified silicon-waste production of ferrosilicon.

  13. TECHNOLOGY AND APPLICATION OF PRODUCT EVOLUTIONARY DESIGN BASED ON CONFIGURATION IN MASS CUSTOMIZATION MODE

    Institute of Scientific and Technical Information of China (English)

    FENG Yixiong; CHENG Jin; TAN Jianrong; ZHENG Bing; WEI Zhe

    2007-01-01

    Product customization has been recognized as an effective means to implement mass customization (MC). A new theory and method for MC-oriented evolutionary design of configuration product is presented based on the study of developing law of evolutionary design in integrated environment, which focuses on the innovation and reuse properties of configuration product. The key technologies for general requirement modeling in quick response to customer requirement, multi-level stepwise configuration optimization driven by customer requirement and evolutionary deduction of product variable structure based on configuration association are thoroughly investigated. The successful application of the presented method in the development of real-life products demonstrates its utility, flexibility and robusticity.

  14. High-speed impact test using an inertial mass and an optical interferometer.

    Science.gov (United States)

    Jin, T; Watanabe, K; Prayogi, I A; Takita, A; Mitatha, S; Djamal, M; Jia, H Z; Hou, W M; Fujii, Y

    2013-07-01

    A high-speed impact testing method for evaluating mechanical properties of materials is proposed using an inertial mass and a dual beat-frequencies laser Doppler interferometer (DB-LDI). In this method, an inertial mass levitated using an aerostatic linear bearing is made to collide with the material being tested at a high initial velocity. During the collision, the velocity of the mass, which is even higher than the critical velocity (±0.56 m/s) defined by the frequency difference of the Zeeman laser, is accurately measured using the DB-LDI. The position, acceleration, and impact force of the mass are calculated from the measured velocity. Using the proposed method, the mechanical properties of a visco-elastic material under a high-speed impact loading condition can be accurately evaluated.

  15. Phenolsulfonphthalein test in healthy sheep and in sheep with reductions in functional renal mass.

    Science.gov (United States)

    Filippich, L J; English, P B; Ainscow, J

    1985-03-01

    The phenolsulfonphthalein (PSP) plasma clearance and urinary excretion tests were applied to sheep before and after 50% and 75% reductions in functional renal mass. The PSP determinants found most useful as indicators of renal mass reduction were the 15-minute urinary excretion percentage and the 60-minute (PSP60) plasma concentration. Although both of these determinants could be used to detect renal mass reduction, the 15-minute PSP excretion percentage was the more sensitive. The PSP60 value was influenced by factors other than reduced nephron numbers; the contraction of the PSP volume of distribution that occurred after renal mass reduction was one important influencing factor. Overall, the PSP tests more accurately reflected the volume of blood delivered to the kidney than the proximal tubular secretory capacity.

  16. An Efficient Test Facility For The Cherenkov Telescope Array FlashCam Readout Electronics Production

    CERN Document Server

    Eisenkolb, F; Kalkuhl, C; Pühlhofer, G; Santangelo, A; Schanz, T; Tenzer, C

    2016-01-01

    The Cherenkov Telescope Array (CTA) is the planned next-generation instrument for ground-based gamma-ray astronomy, currently under preparation by a world-wide consortium. The FlashCam group is preparing a photomultiplier-based camera for the Medium Size Telescopes of CTA, with a fully digital Readout System (ROS). For the forthcoming mass production of a substantial number of cameras, efficient test routines for all components are currently under development. We report here on a test facility for the ROS components. A test setup and routines have been developed and an early version of that setup has successfully been used to test a significant fraction of the ROS for the FlashCam camera prototype in January 2016. The test setup with its components and interface, as well as first results, are presented here.

  17. Probability of background to produce a signal-like excess, for all Higgs masses tested.

    CERN Multimedia

    ATLAS, collaboration

    2012-01-01

    The probability of background to produce a signal-like excess, for all the Higgs boson masses tested. At almost all masses, the probability (solid curve) is at least a few percent; however, at 126.5 GeV it dips to 3x10-7, or one chance in three million, the '5-sigma' gold-standard normally used for the discovery of a new particle. A Standard Model Higgs boson with that mass would produce a dip to 4.6 sigma.

  18. Equipment and methods for rapid analysis of PWO full size scintillation crystals radiation hardness at mass production

    CERN Document Server

    Annenkov, A N; Drobychev, G Yu; Fedorov, A; Ivankin, P; Korzhik, M V; Lecoq, P; Ligun, V; Lopatik, A; Matveev, L; Missevitch, O V; Zouevski, R F; Peigneux, J P; Sigovski, A

    2000-01-01

    This year an extensive R&D on lead tungstate crystals has entered into the pre-production phase at the Bogoroditsk Techno-Chemical Plant (BTCP). Laboratory small-scale PWO crystal growth technology, which has been tuned and optimised over the last years, is transforming now into an industrial technology of mass production. This mass production technology is based on a set of methods and instrumentation for crystal growth, machining, crystal quality control and certification. According to the specification on lead tungstate pre-production crystals, one of the most important categories of tolerance is the radiation hardness. Control of the PWO radiation hardness at the pre-production phase requires reliability and an easy to use measuring tool with a high productivity. A semi- automatic spectrometric setup for PWO radiation hardness monitoring has been developed and tested at the X5 CERN irradiation facility. After final crosschecks the setup was set into operation at the BTCP. Together with several other m...

  19. The mass balance of production and consumption: Supporting policy-makers for aquatic food security

    Science.gov (United States)

    Lopes, A. S.; Ferreira, J. G.; Vale, C.; Johansen, J.

    2017-03-01

    This work addresses divergences between data on consumption and availability for wild-caught and farmed fish, and normalisation of reported production data, to support integrated fisheries and aquaculture management. The methodologies developed, centred on improved parameterisation and on mass balance closure, were tested in two case studies: (i) the cod fishery in Europe, with particular emphasis on Iceland and the United Kingdom; and (ii) the overall balance of aquatic products for Portugal, the ICES member with the most diverse range of landed marine species. Data for consumption, Illegal, Unreported, or Unregulated (IUU) catch, and official availability statistics were used to identify discrepancies between consumption and official availability data. The identification of discrepancies between supply and demand, when coupled with source-discriminated data, showed a pattern where products with no unmet demand tend to display a considerable IUU percentage-above 9% in three cases (hake, sardine, and horse mackerel). By contrast with fished products with an over-met demand such as cod (144%) and sardine (124%), farmed species display low Optimal Consumption Level (OCL) satisfaction. Atlantic salmon, gilthead seabream, and European seabass register 45%, 58% and 44% respectively; this suggests a considerable unmet demand for these products and/or a high volume of undeclared fish reaching consumers, which may be due to the lack of landings control that exists for wild-caught fish. Improvements to production estimates using live-weight coefficients illustrate the impacts of seafood processing. Different processing methods can generate variations in live-weight estimates, leading to errors in officially reported data, and expose the limitations of the current statistical methods. As an example, the corrected per capita consumption for Portugal for 2014 (the latest FAO data) increases from 57 to 66 kg ind-1 y-1, which places the country as the second-greatest consumer in

  20. Numerical analysis of added mass and damping of floating production,storage and offloading system

    Institute of Scientific and Technical Information of China (English)

    Ke Wang; Xi Zhang; Zhi-Qiang Zhang; Wang Xu

    2012-01-01

    An integral equation approach is utilized to investigate the added mass and damping of floating production,storage and offloading system (FPSO system).Finite water depth Green function and higher-order boundary element method are used to solve integral equation.Numerical results about added mass and damping are presented for odd and even mode motions of FPSO.The results show robust convergence in high frequency range and can be used in wave load analysis for FPSO designing and operation.

  1. Photon pressure induced test mass deformation in gravitational-wave detectors

    CERN Document Server

    Hild, S; Danzmann, K; Grote, H; Hewitson, M; Hough, J; Lueck, H; Martin, I; Mossavi, K; Rainer, N; Reid, S; Smith, J R; Strain, K; Weinert, M; Willems, P; Willke, B; Winkler, W

    2007-01-01

    A widely used assumption within the gravitational-wave community has so far been that a test mass acts like a rigid body for frequencies in the detection band, i.e. for frequencies far below the first internal resonance. In this article we demonstrate that localized forces, applied for example by a photon pressure actuator, can result in a non-negligible elastic deformation of the test masses. For a photon pressure actuator setup used in the gravitational wave detector GEO600 we measured that this effect modifies the standard response function by 10% at 1 kHz and about 100% at 2.5 kHz.

  2. Study of Parametric Instability of gravitational wave detectors using silicon test masses

    CERN Document Server

    Zhang, Jue; Ju, Li; Blair, David

    2016-01-01

    Parametric instability is an intrinsic risk in high power laser interferometer gravitational wave detectors, in which the optical cavity modes interact with the acoustic modes of the mirrors leading to exponential growth of the acoustic vibration. In this paper, we investigate the potential parametric instability for a proposed next generation gravitational wave detector based on cooled silicon test masses. It is shown that there would be about 2 unstable modes per test mass, with the highest parametric gain of ~76. The importance of developing suitable instability suppression schemes is emphasized.

  3. Subtraction of test mass angular noise in the LISA Technology Package interferometer

    CERN Document Server

    Cervantes, Felipe Guzmán; Wanner, Gudrun; Heinzel, Gerhard; Danzmann, Karsten

    2012-01-01

    We present recent sensitivity measurements of the LISA Technology Package interferometer with articulated mirrors as test masses, actuated by piezo-electric transducers. The required longitudinal displacement resolution of 9 pm/sqrt[Hz] above 3 mHz has been demonstrated with an angular noise that corresponds to the expected in on-orbit operation. The excess noise contribution of this test mass jitter onto the sensitive displacement readout was completely subtracted by fitting the angular interferometric data streams to the longitudinal displacement measurement. Thus, this cross-coupling constitutes no limitation to the required performance of the LISA Technology Package interferometry.

  4. Mass Properties Testing and Evaluation for the Multi-Mission Radioisotope Thermoelectric Generator

    Energy Technology Data Exchange (ETDEWEB)

    Felicione, Frank S.

    2009-12-01

    Mass properties (MP) measurements were performed for the Multi-Mission Radioisotope Thermoelectric Generator (MMRTG), serial number (S/N) 0X730401, the power system designated for the Mars Science Laboratory (MSL) mission. Measurements were made using new mounting fixtures at the mass properties testing station in the Idaho National Laboratory (INL) Space and Security Power Systems Facility (SSPSF). The objective of making mass properties measurements was to determine the generator’s flight configured mass and center of mass or center of gravity (CG). Using an extremely accurate platform scale, the mass of the as-tested generator was determined to be 100.117 ± 0.007 lb. Weight accuracy was determined by checking the platform scale with calibrated weights immediately prior to weighing the MMRTG.a CG measurement accuracy was assessed by surrogate testing using an inert mass standard for which the CG could be readily determined analytically. Repeated testing using the mass standard enabled the basic measurement precision of the system to be quantified in terms of a physical confidence interval about the measured CG position. However, repetitious testing with the MMRTG itself was not performed in deference to the gamma and neutron radiation dose to operators and the damage potential to the flight unit from extra handling operations. Since the mass standard had been specially designed to have a total weight and CG location that closely matched the MMRTG, the uncertainties determined from its testing were assigned to the MMRTG as well. On this basis, and at the 99% confidence level, a statistical analysis found the direct, as-measured MMRTG-MSL CG to be located at 10.816 ± 0.0011 in. measured perpendicular from the plane of the lower surface of the generator’s mounting lugs (Z direction), and offset from the generator’s long axis centerline in the X and Y directions by 0.0968 ± 0.0040 in. and 0.0276 ± 0.0026 in., respectively. These uncertainties are based

  5. Mass Transfer Testing of a 12.5-cm Rotor Centrifugal Contactor

    Energy Technology Data Exchange (ETDEWEB)

    D. H. Meikrantz; T. G. Garn; J. D. Law; N. R. Mann; T. A. Todd

    2008-09-01

    TRUEX mass transfer tests were performed using a single stage commercially available 12.5 cm centrifugal contactor and stable cerium (Ce) and europium (Eu). Test conditions included throughputs ranging from 2.5 to 15 Lpm and rotor speeds of 1750 and 2250 rpm. Ce and Eu extraction forward distribution coefficients ranged from 13 to 19. The first and second stage strip back distributions were 0.5 to 1.4 and .002 to .004, respectively, throughout the dynamic test conditions studied. Visual carryover of aqueous entrainment in all organic phase samples was estimated at < 0.1 % and organic carryover into all aqueous phase samples was about ten times less. Mass transfer efficiencies of = 98 % for both Ce and Eu in the extraction section were obtained over the entire range of test conditions. The first strip stage mass transfer efficiencies ranged from 75 to 93% trending higher with increasing throughput. Second stage mass transfer was greater than 99% in all cases. Increasing the rotor speed from 1750 to 2250 rpm had no significant effect on efficiency for all throughputs tested.

  6. Development, Production and Testing of 4500 Beam Loss Monitors

    CERN Document Server

    Holzer, E B; Dehning, B; Ferioli, G; Grishin, V; Jimenez, T M; Koshelev, A; Kramer, Daniel; Larionov, A; Taborelli, M; Seleznev, V; Sleptsov, M; Sytin, A; Wevers, I

    2008-01-01

    Beam-loss monitoring (BLM) [1] is a key element in the LHC machine protection. 4250 nitrogen filled ionization chambers (IC) and 350 secondary emission monitors (SEM) have been manufactured and tested at the Institute for High Energy Physics (IHEP) in Protvino, Russia, following their development at CERN. Signal speed and robustness against aging were the main design criteria. Each monitor is permanently sealed inside a stainless-steel cylinder. The quality of the welding was a critical aspect during production. The SEMs are requested to hold a vacuum of $10^{-7}$ bar. Impurity levels from thermal and radiationinduced desorption should remain in the range of parts per million in the ICs. To avoid radiation aging (up to $2·10^{8}$ Gy in 20 years) production of the chambers followed strict UHV requirements. IHEP designed and built the UHV production stand. Due to the required dynamic range of $10^{8}$, the leakage current of the monitors has to stay below 2 pA. Several tests during and after production were ...

  7. Transient productivity index for numerical well test simulations

    Energy Technology Data Exchange (ETDEWEB)

    Blanc, G.; Ding, D.Y.; Ene, A. [Institut Francais du Petrole, Pau (France)] [and others

    1997-08-01

    The most difficult aspect of numerical simulation of well tests is the treatment of the Bottom Hole Flowing (BHF) Pressure. In full field simulations, this pressure is derived from the Well-block Pressure (WBP) using a numerical productivity index which accounts for the grid size and permeability, and for the well completion. This productivity index is calculated assuming a pseudo-steady state flow regime in the vicinity of the well and is therefore constant during the well production period. Such a pseudo-steady state assumption is no longer valid for the early time of a well test simulation as long as the pressure perturbation has not reached several grid-blocks around the well. This paper offers two different solutions to this problem: (1) The first one is based on the derivation of a Numerical Transient Productivity Index (NTPI) to be applied to Cartesian grids; (2) The second one is based on the use of a Corrected Transmissibility and Accumulation Term (CTAT) in the flow equation. The representation of the pressure behavior given by both solutions is far more accurate than the conventional one as shown by several validation examples which are presented in the following pages.

  8. Production of LEU Fully Ceramic Microencapsulated Fuel for Irradiation Testing

    Energy Technology Data Exchange (ETDEWEB)

    Terrani, Kurt A [ORNL; Kiggans Jr, James O [ORNL; McMurray, Jake W [ORNL; Jolly, Brian C [ORNL; Hunt, Rodney Dale [ORNL; Trammell, Michael P [ORNL; Snead, Lance Lewis [ORNL

    2016-01-01

    Fully Ceramic Microencapsulated (FCM) fuel consists of tristructural isotropic (TRISO) fuel particles embedded inside a SiC matrix. This fuel inherently possesses multiple barriers to fission product release, namely the various coating layers in the TRISO fuel particle as well as the dense SiC matrix that hosts these particles. This coupled with the excellent oxidation resistance of the SiC matrix and the SiC coating layer in the TRISO particle designate this concept as an accident tolerant fuel (ATF). The FCM fuel takes advantage of uranium nitride kernels instead of oxide or oxide-carbide kernels used in high temperature gas reactors to enhance heavy metal loading in the highly moderated LWRs. Production of these kernels with appropriate density, coating layer development to produce UN TRISO particles, and consolidation of these particles inside a SiC matrix have been codified thanks to significant R&D supported by US DOE Fuel Cycle R&D program. Also, surrogate FCM pellets (pellets with zirconia instead of uranium-bearing kernels) have been neutron irradiated and the stability of the matrix and coating layer under LWR irradiation conditions have been established. Currently the focus is on production of LEU (7.3% U-235 enrichment) FCM pellets to be utilized for irradiation testing. The irradiation is planned at INL s Advanced Test Reactor (ATR). This is a critical step in development of this fuel concept to establish the ability of this fuel to retain fission products under prototypical irradiation conditions.

  9. Liquid chromatography and liquid chromatography-mass spectrometry analysis of donepezil degradation products

    Directory of Open Access Journals (Sweden)

    Mladenović Aleksandar R.

    2015-01-01

    Full Text Available This study describes the investigation of degradation products of donepezil (DP using stability indicating RP-HPLC method for determination of donepezil, which is a centrally acting reversible acetylcholinesterase inhibitor. In order to investigate the stability of drug and formed degradation products, a forced degradation study of drug sample and finished product under different forced degradation conditions has been conducted. Donepezil hydrochloride and donepezil tablets were subjected to stress degradation conditions recommended by International Conference on Harmonization (ICH. Donepezil hydrochloride solutions were subjected to acid and alkali hydrolysis, chemical oxidation and thermal degradation. Significant degradation was observed under alkali hydrolysis and oxidative degradation conditions. Additional degradation products were observed under the conditions of oxidative degradation. The degradation products observed during forced degradation studies were monitored using the high performance liquid chromatography (HPLC method developed. The parent method was modified in order to obtain LC-MS compatible method which was used to identify the degradation products from forced degradation samples using high resolution mass spectrometry. The mass spectrum provided the precise mass from which derived molecular formula of drug substance and degradation products formed and proved the specificity of the method unambiguously. [Projekat Ministarstva nauke Republike Srbije, br. 172013

  10. Product consistency testing of West Valley Compositional Variation Glasses

    Energy Technology Data Exchange (ETDEWEB)

    Olson, K.M.; Marschman, S.C.; Piepel, G.F.; Whiting, G.K.

    1994-11-01

    Nuclear waste glass produced by the West Valley Demonstration Project (WVDP) must meet the requirements of the Waste Acceptance Preliminary Specification (WAPS) as developed by the US Department of Energy (DOE). To assist WVDP in complying with WAPS, the Materials Characterization Center (MCC) at Pacific Northwest Laboratory (PNL) used the Product Consistency Test (PCT) to evaluate 44 West Valley glasses that had previously been tested in FY 1987 and FY 1988. This report summarizes the results of the PCTs. The glasses tested, which were fabricated as sets of Compositional Variation Glasses for studies performed by the West Valley Support Task (WVST) at PNL during FY 1987 and FY 1988, were doped with Th and U and were variations of West Valley reference glasses. In addition, Approved Reference Material-1 (ARM-1) was used as a test standard (ARM-1 is supplied by the MCC). The PCT was originated at Westinghouse Savannah River Company (WSRC) by C. M. Jantzen and N. R. Bibler (Jantzen and Bibler 1989). The test is a seven-day modified MCC-3 test that uses crushed glass in the size range -100 +200 mesh with deionized water in a Teflon container. There is no agitation during the PCT, and no attempt to include CO{sub 2} from the test environment. Based on B and Li release, the glasses performed about the same as in previous modified MCC-3 testing performed in FY 1987 and FY 1988 (Reimus et al. 1988). The modified MCC-3 tests performed by Reimus et al. were similar to the PCT containers and the exclusion of CO{sub 2} from the tests.

  11. Development and Testing of the VAHIRR Radar Product

    Science.gov (United States)

    Barrett, Joe III; Miller, Juli; Charnasky, Debbie; Gillen, Robert; Lafosse, Richard; Hoeth, Brian; Hood, Doris; McNamara, Todd

    2008-01-01

    Lightning Launch Commit Criteria (LLCC) and Flight Rules (FR) are used for launches and landings at government and commercial spaceports. They are designed to avoid natural and triggered lightning strikes to space vehicles, which can endanger the vehicle, payload, and general public. The previous LLCC and FR were shown to be overly restrictive, potentially leading to costly launch delays and scrubs. A radar algorithm called Volume Averaged Height Integrated Radar Reflectivity (VAHIRR), along with new LLCC and FR for anvil clouds, were developed using data collected by the Airborne Field Mill II research program. VAHIRR is calculated at every horizontal position in the coverage area of the radar and can be displayed similar to a two-dimensional derived reflectivity product, such as composite reflectivity or echo tops. It is the arithmetic product of two quantities not currently generated by the Weather Surveillance Radar 1988 Doppler (WSR-88D): a volume average of the reflectivity measured in dBZ and the average cloud thickness based on the average echo top height and base height. This presentation will describe the VAHIRR algorithm, and then explain how the VAHIRR radar product was implemented and tested on a clone of the National Weather Service's (NWS) Open Radar Product Generator (ORPG-clone). The VAHIRR radar product was then incorporated into the Advanced Weather Interactive Processing System (AWIPS), to make it more convenient for weather forecasters to utilize. Finally, the reliability of the VAHIRR radar product was tested with real-time level II radar data from the WSR-88D NWS Melbourne radar.

  12. Ground Testing and Flight Demonstration of Charge Management of Insulated Test Masses Using UV LED Electron Photoemission

    OpenAIRE

    Saraf, Shailendhar; Buchman, Sasha; Balakrishnan, Karthik; Lui, Chin Yang; Soulage, Michael; Faied, Dohy; Hanson, John; Ling, Kuok; Jaroux, Belgacem; AlRashed, Abdullah; Nassban, Badr Al; Suwaidan, Badr Al; Harbi, Mohammed Al; Salamah, Badr Bin; Othman, Mohammed Bin

    2016-01-01

    The UV LED mission demonstrates the precise control of the potential of electrically isolated test masses that is essential for the operation of space accelerometers and drag free sensors. Accelerometers and drag free sensors were and remain at the core of geodesy, aeronomy, and precision navigation missions as well as gravitational science experiments and gravitational wave observatories. Charge management using photoelectrons generated by the 254 nm UV line of Hg was first demonstrated on G...

  13. Multiday production of condensing organic aerosol mass in urban and forest outflow

    Directory of Open Access Journals (Sweden)

    J. Lee-Taylor

    2014-07-01

    Full Text Available Secondary organic aerosol (SOA production in air masses containing either anthropogenic or biogenic (terpene-dominated emissions is investigated using the explicit gas-phase chemical mechanism generator GECKO-A. Simulations show several-fold increases in SOA mass continuing for several days in the urban outflow, even as the initial air parcel is diluted into the regional atmosphere. The SOA mass increase in the forest outflow is more modest (∼50% and of shorter duration (1–2 days. The production in the urban outflow stems from continuing oxidation of gas-phase precursors which persist in equilibrium with the particle phase, and can be attributed to multigenerational reaction products of both aromatics and alkanes. In particular we find large contributions from substituted maleic anhydrides and multi-substituted peroxide-bicyclic alkenes. The results show that the predicted production is a robust feature of our model even under changing atmospheric conditions, and contradict the notion that SOA undergoes little mass production beyond a short initial formation period. The results imply that anthropogenic aerosol precursors could influence the chemical and radiative characteristics of the atmosphere over an extremely wide region, and that SOA measurements near precursor sources may routinely underestimate this influence.

  14. On-ground testing of the role of adhesion in the LISA-Pathfinder test mass injection phase

    Science.gov (United States)

    Bortoluzzi, D.; Zanoni, C.; Conklin, J. W.

    2017-05-01

    Many space missions share the need to fly a free-falling body inside the spacecraft, as a reference for navigation and/or as a probe for the local gravitational field. When a mechanism is required to cage such an object during the launch phase, the need arises to release it to free-fall once the operational phase must be initiated in orbit. The criticality of this phase increases when the mechanical interfaces between the body and the mechanism are affected by adhesion and the actuation authority of the control system on the free-falling body is limited. Both conditions are realized in the LISA Pathfinder mission, which aims at injecting a gold-coated 2 kg cubic test mass into a nearly perfect geodesic trajectory to demonstrate the readiness of the developed technology for in-space gravity wave detection. The criticality of adhesion is widely recognized in space technology, because it can affect and jeopardize the functionality of mechanisms, when arising between moving parts. In the LISA Pathfinder case, metallic adhesion potentially plays a relevant role, mainly for two reasons. First, thanks to its properties (ductility, high surface energy) the gold coating on the proof mass easily produces cold weldings, especially in vacuum conditions. Second, the detachment of the proof mass from the releasing device occurs abruptly and a relevant influence of the separation velocity is expected on the strength of the welding. This can produce an excessive velocity of the proof mass at the retraction of the releasing device for the following capture and centring phase on behalf of the control system. A testing activity is performed to characterize the dynamic behaviour of the adhesive bonds between the proof mass and the releasing device, which can be used to predict their contribution on the residual velocity of the proof mass after in-flight release. The study of such a dynamic phenomenon sets some challenging requirements on the measurement technique, both on the

  15. Journal: A Review of Some Tracer-Test Design Equations for Tracer-Mass Estimation and Sample Collection Frequency

    Science.gov (United States)

    Determination of necessary tracer mass, initial sample-collection time, and subsequent sample-collection frequency are the three most difficult aspects to estimate for a proposed tracer test prior to conducting the tracer test. To facilitate tracer-mass estimation, 33 mass-estima...

  16. Journal: A Review of Some Tracer-Test Design Equations for Tracer-Mass Estimation and Sample Collection Frequency

    Science.gov (United States)

    Determination of necessary tracer mass, initial sample-collection time, and subsequent sample-collection frequency are the three most difficult aspects to estimate for a proposed tracer test prior to conducting the tracer test. To facilitate tracer-mass estimation, 33 mass-estima...

  17. Analysis of borehole expansion and gallery tests in anisotropic rock masses

    Science.gov (United States)

    Amadei, B.; Savage, W.Z.

    1991-01-01

    Closed-form solutions are used to show how rock anisotropy affects the variation of the modulus of deformation around the walls of a hole in which expansion tests are conducted. These tests include dilatometer and NX-jack tests in boreholes and gallery tests in tunnels. The effects of rock anisotropy on the modulus of deformation are shown for transversely isotropic and regularly jointed rock masses with planes of transverse isotropy or joint planes parallel or normal to the hole longitudinal axis for plane strain or plane stress condition. The closed-form solutions can also be used when determining the elastic properties of anisotropic rock masses (intact or regularly jointed) in situ. ?? 1991.

  18. Phase 1 pixel modules production and High Density Interconnect testing

    CERN Document Server

    Still, Joseph

    2014-01-01

    During the first run of the LHC, luminosity peaked at $1 \\times 10^{34} cm^{-2}s^{-1}$ with $ \\approx 50 ns$ bunch spacing a pile-up of about 25, or simultaneous inelastic collisions per crossing, occur in the CMS experiment. However after the upgrade of of the LHC during long shut down 1, luminosity, and therefore pile-up. Therefore the CMS pixel tracker has to be upgraded to be able to operate correctly under this news stronger constraints. That is how this CERN Summer Student project, which took place at the CERN Meyrin site, comes within the framework of the pixel detector upgrade in the CMS experiment with a work aimed on the phase 1 of pixel modules production and tests of the HDI. The production and tests of the HDI were held in cleanroom facilities. This included first hand as well as to work on pixel modules building and performing size and flatness tests on them, and on a other hand testing several HDIs. At first, prototypes modules were assembled before real modules building. Another aspect of work...

  19. APALS program status: preproduction flight test results and production implementation

    Science.gov (United States)

    Hvizd, James J.; Dieffenbach, Otto W.

    1996-05-01

    The APALS system is a precision approach and landing system designed to enable low visibility landings at many more airports than now possible. Engineering development of the APALS system began October 1992 culminating in the pre- production Advanced Development Model (ADM) system currently undergoing flight testing. The paper focuses on the Cat III accuracy and integrity requirements defined by ICAO, Annex 10 and the required navigation performance (RNP) tunnel concept. The resulting ADM architecture developed to meet them is described. The primary measurement is made with the aircraft's weather radar and provides range and range rate information to the ADM necessary to update the precision navigation state vector. The system uses stored terrain map data as references for map matching with synthetic aperture radar with synthetic aperture radar maps. A description of the pre-production flight test program is included. Testing is being conducted at six different airports around the country demonstrating system performance in various environmental conditions (precipitation, heavy foliage, sparse terrain, over water and turbulence). ADM flight test results of 131 successful CAT II hand-flown approaches at ALbuquerque, NM and Richmond, VA are presented. Detailed statistical analysis of these results indicate that the APALS system meets the RNP for Cat III.

  20. Endurance test on IR rig for RI production

    Energy Technology Data Exchange (ETDEWEB)

    Chung, Heung June; Youn, Y. J.; Han, H. S.; Hong, S. B.; Cho, Y. G.; Ryu, J. S

    2000-12-01

    This report presents the pressure drop, vibration and endurance test results for IR rig for RI production which were desigened and fabricated by KAERI. From the pressure drop test results, it is noted that the flow rate through the IR rig corresponding to the pressure drop of 200 kPa is measured to be about 3.12 kg/sec. Vibration frequency for the IR rig ranges from 13 to 17 Hz. RMS(Root Mean Square) displacement for the IR rig is less than 30 {mu}m, and the maximum displacement is less than 110{mu}m. These experimental results show that the design criteria of IR rig meet the HANARO limit conditions. Endurance test results show that the appreciable fretting wear for the IR rig does not occur, however tiny trace of wear between contact points is observed.

  1. Testing the Environmental Dependence of the Stellar Initial Mass Function - the Case of L1641

    Science.gov (United States)

    Hsu, Wen-hsin; Hartmann, L.; Allen, L.; Hernandez, J.; Megeath, T.

    2012-01-01

    To test the proposition that the stellar initial mass function (IMF) depends on the environmental density, we conducted an optical spectroscopic and photometric survey of the young stellar population in L1641, a low-density, star-forming region of the Orion A cloud south of the dense Orion Nebula Cluster (ONC). We used low-resolution optical spectra and optical photometry, as well as the Spitzer IRAC photometry (Megeath et al. 2011) to identify members and obtain spectral types. As of now, we have confirmed and spectral-typed 648 members and project a total number of 780 members with moderate extinction. Our study suggests a comparison between L1641 and the ONC can yield a statistically-significant test of the dependence of the upper mass portion of the stellar initial mass function upon environment. Our preliminary results indicate that L1641 may well be deficient in O and early B stars.

  2. Collision-Induced Dissociation Mass Spectrometry: A Powerful Tool for Natural Product Structure Elucidation.

    Science.gov (United States)

    Johnson, Andrew R; Carlson, Erin E

    2015-11-03

    Mass spectrometry is a powerful tool in natural product structure elucidation, but our ability to directly correlate fragmentation spectra to these structures lags far behind similar efforts in peptide sequencing and proteomics. Often, manual data interpretation is required and our knowledge of the expected fragmentation patterns for many scaffolds is limited, further complicating analysis. Here, we summarize advances in natural product structure elucidation based upon the application of collision induced dissociation fragmentation mechanisms.

  3. Mechanical Q-factor measurements on a test mass with a structured surface

    Energy Technology Data Exchange (ETDEWEB)

    Nawrodt, R [Institut fuer Festkoerperphysik, Friedrich-Schiller-Universitaet Jena, Helmholtzweg 5, D-07743 Jena (Germany); Zimmer, A [Institut fuer Festkoerperphysik, Friedrich-Schiller-Universitaet Jena, Helmholtzweg 5, D-07743 Jena (Germany); Koettig, T [Institut fuer Festkoerperphysik, Friedrich-Schiller-Universitaet Jena, Helmholtzweg 5, D-07743 Jena (Germany); Clausnitzer, T [Institut fuer Angewandte Physik, Friedrich-Schiller-Universitaet Jena, Max-Wien-Platz 1, D-07743 Jena (Germany); Bunkowski, A [Max-Planck-Institut fuer Gravitationsphysik (Albert-Einstein-Institut) and Institut fuer Gravitationsphysik, Leibniz Universitaet Hannover, Callinstr. 38, D-30167 Hannover (Germany); Kley, E B [Institut fuer Angewandte Physik, Friedrich-Schiller-Universitaet Jena, Max-Wien-Platz 1, D-07743 Jena (Germany); Schnabel, R [Max-Planck-Institut fuer Gravitationsphysik (Albert-Einstein-Institut) and Institut fuer Gravitationsphysik, Leibniz Universitaet Hannover, Callinstr. 38, D-30167 Hannover (Germany); Danzmann, K [Max-Planck-Institut fuer Gravitationsphysik (Albert-Einstein-Institut) and Institut fuer Gravitationsphysik, Leibniz Universitaet Hannover, Callinstr. 38, D-30167 Hannover (Germany); Nietzsche, S [Institut fuer Festkoerperphysik, Friedrich-Schiller-Universitaet Jena, Helmholtzweg 5, D-07743 Jena (Germany); Vodel, W [Institut fuer Festkoerperphysik, Friedrich-Schiller-Universitaet Jena, Helmholtzweg 5, D-07743 Jena (Germany); Tuennermann, A [Institut fuer Angewandte Physik, Friedrich-Schiller-Universitaet Jena, Max-Wien-Platz 1, D-07743 Jena (Germany); Seidel, P [Institut fuer Festkoerperphysik, Friedrich-Schiller-Universitaet Jena, Helmholtzweg 5, D-07743 Jena (Germany)

    2007-07-15

    We present mechanical Q-factors (quality factors) of a crystalline quartz test mass with a nano-structured surface, measured in the temperature regime from 5 to 300 K. The nano-structure was a grating with a period of 2 {mu}m and a depth of about 0.1 {mu}m. Comparative measurements were performed on the plain substrate and on the structured test mass with different numbers of SiO{sub 2}/Ta{sub 2}O{sub 5} coating layers. The measurements at different stages of the test mass fabrication process show that the surface distortion induced by the nanostructure does not severely lower the mechanical Q-factor of the substrate. Damping due to a multi-layer coating stack was found to be orders of magnitude higher. The results provide vital information concerning the potential usage of low-thermal noise nano-structured test masses in future generations of high-precision laser interferometers and in current attempts to measure quantum effects of macroscopic mirror oscillators.

  4. A wide variety of injection molding technologies is now applicable to small series and mass production

    Science.gov (United States)

    Bloß, P.; Jüttner, G.; Jacob, S.; Löser, C.; Michaelis, J.; Krajewsky, P.

    2014-05-01

    Micro plastic parts open new fields for application, e. g., to electronics, sensor technologies, optics, and medical engineering. Before micro parts can go to mass production, there is a strong need of having the possibility for testing different designs and materials including material combinations. Hence, flexible individual technical and technological solutions for processing are necessary. To manufacture high quality micro parts, a micro injection moulding machine named formicaPlast based on a two-step plunger injection technology was developed. Resulting from its design, the residence time and the accuracy problems for managing small shot volumes with reproducible high accuracy are uncompromisingly solved. Due to their simple geometry possessing smooth transitions and non adherent inner surfaces, the plunger units allow to process "all" thermoplastics from polyolefines to high performance polymers, optical clear polymers, thermally sensitive bioresorbables, highly filled systems (the so-called powder injection molding PIM), and liquid silicon rubber (LSR, here with a special kit). The applied platform strategy in the 1K and 2K version allows integrating automation for assembling, handling and packaging. A perpendicular arrangement allows encapsulation of inserts, also partially, and integration of this machine into process chains. Considering a wide variety of different parts consisting of different materials, the high potential of the technology is demonstrated. Based on challenging industrial parts from electronic applications (2K micro MID and bump mat, where both are highly structured parts), the technological solutions are presented in more detail.

  5. A wide variety of injection molding technologies is now applicable to small series and mass production

    Energy Technology Data Exchange (ETDEWEB)

    Bloß, P., E-mail: bloss@kuz-leipzig.de, E-mail: juettner@kuz-leipzig.de, E-mail: jacob@kuz-leipzig.de, E-mail: loeser@kuz-leipzig.de, E-mail: michaelis@kuz-leipzig.de, E-mail: krajewsky@kuz-leipzig.de; Jüttner, G., E-mail: bloss@kuz-leipzig.de, E-mail: juettner@kuz-leipzig.de, E-mail: jacob@kuz-leipzig.de, E-mail: loeser@kuz-leipzig.de, E-mail: michaelis@kuz-leipzig.de, E-mail: krajewsky@kuz-leipzig.de; Jacob, S., E-mail: bloss@kuz-leipzig.de, E-mail: juettner@kuz-leipzig.de, E-mail: jacob@kuz-leipzig.de, E-mail: loeser@kuz-leipzig.de, E-mail: michaelis@kuz-leipzig.de, E-mail: krajewsky@kuz-leipzig.de; Löser, C., E-mail: bloss@kuz-leipzig.de, E-mail: juettner@kuz-leipzig.de, E-mail: jacob@kuz-leipzig.de, E-mail: loeser@kuz-leipzig.de, E-mail: michaelis@kuz-leipzig.de, E-mail: krajewsky@kuz-leipzig.de; Michaelis, J., E-mail: bloss@kuz-leipzig.de, E-mail: juettner@kuz-leipzig.de, E-mail: jacob@kuz-leipzig.de, E-mail: loeser@kuz-leipzig.de, E-mail: michaelis@kuz-leipzig.de, E-mail: krajewsky@kuz-leipzig.de; Krajewsky, P., E-mail: bloss@kuz-leipzig.de, E-mail: juettner@kuz-leipzig.de, E-mail: jacob@kuz-leipzig.de, E-mail: loeser@kuz-leipzig.de, E-mail: michaelis@kuz-leipzig.de, E-mail: krajewsky@kuz-leipzig.de [Kunststoff-Zentrum in Leipzig gGmbH (KuZ), Leipzig (Germany)

    2014-05-15

    Micro plastic parts open new fields for application, e. g., to electronics, sensor technologies, optics, and medical engineering. Before micro parts can go to mass production, there is a strong need of having the possibility for testing different designs and materials including material combinations. Hence, flexible individual technical and technological solutions for processing are necessary. To manufacture high quality micro parts, a micro injection moulding machine named formicaPlast based on a two-step plunger injection technology was developed. Resulting from its design, the residence time and the accuracy problems for managing small shot volumes with reproducible high accuracy are uncompromisingly solved. Due to their simple geometry possessing smooth transitions and non adherent inner surfaces, the plunger units allow to process 'all' thermoplastics from polyolefines to high performance polymers, optical clear polymers, thermally sensitive bioresorbables, highly filled systems (the so-called powder injection molding PIM), and liquid silicon rubber (LSR, here with a special kit). The applied platform strategy in the 1K and 2K version allows integrating automation for assembling, handling and packaging. A perpendicular arrangement allows encapsulation of inserts, also partially, and integration of this machine into process chains. Considering a wide variety of different parts consisting of different materials, the high potential of the technology is demonstrated. Based on challenging industrial parts from electronic applications (2K micro MID and bump mat, where both are highly structured parts), the technological solutions are presented in more detail.

  6. Calculation of isotopic mass and energy production by a matrix operator method. [Volterra method of the multiplicative integral

    Energy Technology Data Exchange (ETDEWEB)

    Lee, C.E.

    1976-08-01

    The Volterra method of the multiplicative integral is used to determine the isotopic density, mass, and energy production in linear systems. The solution method, assumptions, and limitations are discussed. The method allows a rapid accurate calculation of the change in isotopic density, mass, and energy production independent of the magnitude of the time steps, production or decay rates, or flux levels.

  7. A novel mass spectrometric method for formaldehyde in children's personal-care products and water via derivatization with acetylacetone.

    Science.gov (United States)

    Backe, Will J

    2017-06-30

    New legislation in the state of Minnesota prohibits the sale of children's personal-care products (PCPs) that contain more than 500 ng/mg formaldehyde. Previous attempts to quantify formaldehyde in PCPs use nonspecific derivatization procedures that employ harsh reagents and/or nonspecific detection. Derivatization of formaldehyde by acetylacetone occurs under mild conditions and is specific for formaldehyde but it has not been investigated using high-performance liquid chromatography/tandem mass-spectrometry (HPLC/MS/MS). To determine formaldehyde, PCPs were dissolved and then interferences were minimized by graphitized-carbon solid-phase extraction. Formaldehyde was derivatized to 3,5-diacetyl-1,4-dihydrolutidine (DDL) using an acetylacetone solution. Post-derivatization, samples were diluted and analyzed by HPLC/MS/MS. Quantification was performed by isotopic dilution. Product-ion spectra were acquired for DDL and D12 -DDL. The mass shifts between the two product-ion spectra were used to assign fragment structures. To confirm molecular formulas, high-resolution accurate-mass analysis of the DDL product ions was performed by quadrupole time-of-flight MS. Structures were proposed for all product ions of DDL above 10% relative intensity. Method accuracy ranged between 96-104% for all matrices at all concentrations tested. Method precision was less than 4% relative standard deviation. The reporting limit was 10 ng/mg in PCPs and 100 μg/L in water. Twenty children's PCPs were tested to demonstrate the method and formaldehyde was reported in five from 23-1500 ng/mg. Of those five, two samples contained formaldehyde above the Minnesota regulatory limit. The developed method allows for the accurate quantification of formaldehyde in PCPs at levels below those required by a new regulation on children's products in Minnesota. The method includes a derivatization procedure that is newly adapted to HPLC/MS/MS; therefore, structures were proposed for the product ions of

  8. New Balancing Equipment for Mass Production of Small and Medium-Sized Electrical Machines

    DEFF Research Database (Denmark)

    Argeseanu, Alin; Ritchie, Ewen; Leban, Krisztina Monika

    2010-01-01

    The level of vibration and noise is an important feature. It is good practice to explain the significance of the indicators of the quality of electrical machines. The mass production of small and medium-sized electrical machines demands speed (short typical measurement time), reliability...

  9. Advantages of exclusive \\gamma\\gamma production to probe high mass systems

    CERN Document Server

    Martin, A D

    2016-01-01

    We recall that the exclusive production of high mass objects via \\gamma\\gamma fusion at the LHC is not strongly suppressed in comparison with inclusive \\gamma\\gamma fusion. Therefore it may be promising to study new objects produced by the \\gamma\\gamma subprocess in experiments with exclusive kinematics. We list the main advantages of exclusive experiments.

  10. Rapid differentiation of tea products by surface desorption atmospheric pressure chemical ionization mass spectrometry.

    Science.gov (United States)

    Chen, Huanwen; Liang, Huazheng; Ding, Jianhua; Lai, Jinhu; Huan, Yanfu; Qiao, Xiaolin

    2007-12-12

    Protonated water molecules generated by an ambient corona discharge were directed to impact tea leaves for desorption/ionization at atmospheric pressure. Thus, a novel method based on surface desorption chemical ionization mass spectrometry (DAPCI-MS) has been developed for rapid analysis of tea products without any sample pretreatment. Under the optimized experimental conditions, DAPCI MS spectra of various tea samples are recorded rapidly, and the resulting mass spectra are chemical fingerprints that characterize the tea samples. On the basis of the mass spectral fingerprints, 40 tea samples including green tea, oolong tea, and jasmine tea were successfully differentiated by principal component analysis (PCA) of the mass spectral raw data. The PCA results were also validated with cluster analysis and supervised PCA analysis. The alteration of signal intensity caused by rough surfaces of tea leaves did not cause failure in the separation of the tea products. The experimental findings show that DAPCI-MS creates ions of both volatile and nonvolatile compounds in tea products at atmospheric pressure, providing a practical and convenient tool for high-throughput differentiation of tea products.

  11. Microbial transglutaminase production by Streptoverticillium mobaraense: Analysis of amino acid metabolism using mass balances

    NARCIS (Netherlands)

    Zhu, Y.; Rinzema, A.; Bonarius, H.P.J.; Tramper, J.; Bol, J.

    1998-01-01

    Metabolic flows, especially those of amino acids, were determined and analyzed at different stages of a batch fermentation for microbial transglutaminase production by Streptoverticillium mobaraense. The method is mainly based on mass balances and measurements of amino acids and other metabolites. T

  12. Northeast Atlantic Late Quaternary planktic Foraminifera as primary productivity and water mass indicators

    NARCIS (Netherlands)

    Kreveld, van S.A.

    1996-01-01

    Primary productivity and water mass reconstructions based on planktic Foraminifera reveal distinct interglacial/glacial variations for the past 208 ka in a mid-latitude Northeast Atlantic piston core. Average total planktic foraminiferal absolute frequencies and accumulation rates, which are

  13. Microbial transglutaminase production by Streptoverticillium mobaraense: Analysis of amino acid metabolism using mass balances

    NARCIS (Netherlands)

    Zhu, Y.; Rinzema, A.; Bonarius, H.P.J.; Tramper, J.; Bol, J.

    1998-01-01

    Metabolic flows, especially those of amino acids, were determined and analyzed at different stages of a batch fermentation for microbial transglutaminase production by Streptoverticillium mobaraense. The method is mainly based on mass balances and measurements of amino acids and other metabolites. T

  14. Critical Mass in the Production of Ph.D.s: A Multi-Disciplinary Study.

    Science.gov (United States)

    Scott, Frank; Anstine, Jeff

    2002-01-01

    Uses survivor analysis to evaluate critical mass and minimum efficient scale in the production of Ph.D.s in four academic disciplines: economics, history, physics, and psychology. Finds that size and quality ranking are positively correlated in economics, history, and physics, but no such relationship is apparent in psychology. (Contains 17…

  15. Detection and analysis of polymerase chain reaction products by mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Hurst, G.B., Doktycz, M.J., Britt, P.F., Vass, A.A., Buchanan, M.V.

    1997-02-01

    This paper describes recent and ongoing efforts to overcome some of the obstacles to more routine and robust application of MALDI-TOF to analysis of polymerase chain reaction products and other information- bearing nucleic acid molecules. Methods for purifying nucleic acid samples are described, as is the application of delayed extraction TOF mass spectrometry to analysis of short oligonucleotides.

  16. Top quark mass effects in Higgs boson pair production up to NNLO

    CERN Document Server

    Hoff, Jens

    2016-01-01

    We consider the production of pairs of Standard Model Higgs bosons via gluon fusion. Until recently the full dependence on the top quark mass $M_t$ was not known at next-to-leading order. For this reason we apply an approximation based on the expansion for large top quark masses up to $\\mathcal{O}(1/M_t^{12})$. At next-to-next-to-leading order we avoid the calculation of real corrections via the soft-virtual approximation and obtain top quark mass corrections up to $\\mathcal{O}(1/M_t^4)$. We use our results to estimate the residual uncertainty of the total cross section due to a finite top quark mass to be $\\mathcal{O}(10\\%)$ at next-to-leading order and $\\mathcal{O}(5\\%)$ at next-to-next-to-leading order.

  17. Higgs boson pair production in gluon fusion at NLO with full top-quark mass dependence

    CERN Document Server

    Borowka, S; Heinrich, G; Jones, S P; Kerner, M; Schlenk, J; Schubert, U; Zirke, T

    2016-01-01

    We present the calculation of the cross section and invariant mass distribution for Higgs boson pair production in gluon fusion at next-to-leading order (NLO) in QCD. Top-quark masses are fully taken into account throughout the calculation. The virtual two-loop amplitude has been generated using an extension of the program GoSam supplemented with an interface to Reduze for the integral reduction. The occurring integrals have been calculated numerically using the program SecDec. Our results, including the full top-quark mass dependence for the first time, allow us to assess the validity of various approximations proposed in the literature, which we also recalculate. We find substantial deviations between the NLO result and the different approximations, which emphasizes the importance of including the full top-quark mass dependence at NLO.

  18. Standard test methods for chemical, mass spectrometric, spectrochemical, nuclear, and radiochemical analysis of uranium hexafluoride

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2011-01-01

    1.1 These test methods cover procedures for subsampling and for chemical, mass spectrometric, spectrochemical, nuclear, and radiochemical analysis of uranium hexafluoride UF6. Most of these test methods are in routine use to determine conformance to UF6 specifications in the Enrichment and Conversion Facilities. 1.2 The analytical procedures in this document appear in the following order: Note 1—Subcommittee C26.05 will confer with C26.02 concerning the renumbered section in Test Methods C761 to determine how concerns with renumbering these sections, as analytical methods are replaced with stand-alone analytical methods, are best addressed in subsequent publications. Sections Subsampling of Uranium Hexafluoride 7 - 10 Gravimetric Determination of Uranium 11 - 19 Titrimetric Determination of Uranium 20 Preparation of High-Purity U3O 8 21 Isotopic Analysis 22 Isotopic Analysis by Double-Standard Mass-Spectrometer Method 23 - 29 Determination of Hydrocarbons, Chlorocarbons, and Partially Substitut...

  19. Dust Production and Mass Loss in the Galactic Globular Cluster NGC 362

    CERN Document Server

    Boyer, Martha L; van Loon, Jacco Th; Gordon, Karl D; Babler, Brian; Block, Miwa; Bracker, Steve; Engelbracht, Charles; Hora, Joe; Indebetouw, Remy; Meade, Marilyn; Meixner, Margaret; Misselt, Karl; Oliveira, Joana M; Sewilo, Marta; Shiao, Bernie; Whitney, Barbara

    2009-01-01

    We investigate dust production and stellar mass loss in the Galactic globular cluster NGC 362. Due to its close proximity to the Small Magellanic Cloud (SMC), NGC 362 was imaged with the IRAC and MIPS cameras onboard the Spitzer Space Telescope as part of the Surveying the Agents of Galaxy Evolution (SAGE-SMC) Spitzer Legacy program. We detect several cluster members near the tip of the Red Giant Branch that exhibit infrared excesses indicative of circumstellar dust and find that dust is not present in measurable quantities in stars below the tip of the Red Giant Branch. We modeled the spectral energy distribution (SED) of the stars with the strongest IR excess and find a total cluster dust mass-loss rate of 3.0(+2.0/-1.2) x 10^-9 solar masses per year, corresponding to a gas mass-loss rate of 8.6(+5.6/-3.4) x 10^-6 solar masses per year, assuming [Fe/H] = -1.16. This mass loss is in addition to any dust-less mass loss that is certainly occurring within the cluster. The two most extreme stars, variables V2 an...

  20. Precision Test of the Isobaric Multiplet Mass Equation in the A = 32, T = 2 Quintet

    Science.gov (United States)

    Ferrer, R.; Kwiatkowski, A. A.; Bollen, G.; Campbell, C. M.; Folden, C. M., III; Lincoln, D.; Morrissey, D. J.; Pang, G. K.; Prinke, A.; Savory, J.; Schwarz, S.

    2008-10-01

    Masses of the radionuclides ^32,33Si and ^34P and of the stable nuclide ^32S have been measured with the Low Energy Beam and Ion Trap (LEBIT) Penning trap mass spectrometer. Relative mass uncertainties of 3 x 10-8 and better have been achieved. The measured mass value of ^32Si differs from the literature value [1,2] by four standard deviations. The precise mass determination of ^32Si and ^32S have been employed to test the isobaric multiplet mass equation for the A = 32, T= 2 isospin quintet. The experimental results indicate a significant deviation from the quadratic form. This work has been supported by Michigan State University, the NSF under contract number PHY- 0606007, and the DOE under the contract DE-FG02-00ER41144. References: 1. G. Audi, A.H. Wapstra, and C. Thibault, Nucl. Phys. A729 (2003) 337 2. A. Paul, S. R"ottger, A. Zimbal, and U. Keyser, Hyperfine Interact. 132 (2001) 189

  1. Integrated configurable equipment selection and line balancing for mass production with serial-parallel machining systems

    Science.gov (United States)

    Battaïa, Olga; Dolgui, Alexandre; Guschinsky, Nikolai; Levin, Genrikh

    2014-10-01

    Solving equipment selection and line balancing problems together allows better line configurations to be reached and avoids local optimal solutions. This article considers jointly these two decision problems for mass production lines with serial-parallel workplaces. This study was motivated by the design of production lines based on machines with rotary or mobile tables. Nevertheless, the results are more general and can be applied to assembly and production lines with similar structures. The designers' objectives and the constraints are studied in order to suggest a relevant mathematical model and an efficient optimization approach to solve it. A real case study is used to validate the model and the developed approach.

  2. Apollo Soyuz Test Project Weights and Mass Properties Operational Management System

    Science.gov (United States)

    Collins, M. A., Jr.; Hischke, E. R.

    1975-01-01

    The Apollo Soyuz Test Project (ASTP) Weights and Mass Properties Operational Management System was established to assure a timely and authoritative method of acquiring, controlling, generating, and disseminating an official set of vehicle weights and mass properties data. This paper provides an overview of the system and its interaction with the various aspects of vehicle and component design, mission planning, hardware and software simulations and verification, and real-time mission support activities. The effect of vehicle configuration, design maturity, and consumables updates is discussed in the context of weight control.

  3. Standard test method for uranium and plutonium concentrations and isotopic abundances by thermal ionization mass spectrometry

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2005-01-01

    1.1 This test method covers the determination of the concentration and isotopic composition of uranium and plutonium in solutions. The purified uranium or plutonium from samples ranging from nuclear materials to environmental or bioassay matrices is loaded onto a mass spectrometric filament. The isotopic ratio is determined by thermal ionization mass spectrometry, the concentration is determined by isotope dilution. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish safety and health practices and determine the applicability of regulatory limitations prior to use.

  4. Production of cement requiring low energy expenditure. An industrial test

    Energy Technology Data Exchange (ETDEWEB)

    Gimenez, S.; Blanco, M.T.; Palomo, A.; Puertas, F. (Instituto de Ciencias de la Construccion, Madrid (Spain))

    1991-01-01

    A new method for making cement is proposed. It is based on the use of CaF{sub 2} and CaSO{sub 4} for partial replacement of the usual raw materials in cement manufacturing. This paper shows the feasibility of the proposed method on an industrial scale. A test carried out in a Spanish cement factory (1500 t yield of the new cement) has revealed that the mehtod can not only be adapted to the current technology but also requires a much lower energy expenditure. The final product is shown to have excellent properties in comparison with OPC. (orig.).

  5. Determination of the top-quark mass from hadro-production of single top-quarks

    CERN Document Server

    Alekhin, S; Thier, S

    2016-01-01

    We present a new determination of the top-quark mass $m_t$ based on the experimental data from the Tevatron and the LHC for single-top hadro-production. We use the inclusive cross sections of $s$- and $t$-channel top-quark production to extract $m_t$ and to minimize the dependence on the strong coupling constant and the gluon distribution in the proton compared to the hadro-production of top-quark pairs. As part of our analysis we compute the next-to-next-to-leading order approximation for the $s$-channel cross section in perturbative QCD based on the known soft-gluon corrections and implement it in the program Hathor for the numerical evaluation of the hadronic cross section. Results for the top-quark mass are reported in the $\\bar{MS}$ and in the on-shell renormalization scheme.

  6. Determination of the top-quark mass from hadro-production of single top-quarks

    Science.gov (United States)

    Alekhin, S.; Moch, S.; Thier, S.

    2016-12-01

    We present a new determination of the top-quark mass mt based on the experimental data from the Tevatron and the LHC for single-top hadro-production. We use the inclusive cross sections of s- and t-channel top-quark production to extract mt and to minimize the dependence on the strong coupling constant and the gluon distribution in the proton compared to the hadro-production of top-quark pairs. As part of our analysis we compute the next-to-next-to-leading order approximation for the s-channel cross section in perturbative QCD based on the known soft-gluon corrections and implement it in the program HATHOR for the numerical evaluation of the hadronic cross section. Results for the top-quark mass are reported in the MS ‾ and in the on-shell renormalization scheme.

  7. Low Speed PSP Testing in Production Wind Tunnels

    Science.gov (United States)

    Bell, James; Mehta, Rabi; Schairer, Ed; Hand, Larry; Nixon, David (Technical Monitor)

    1998-01-01

    The brightness signal from a pressure-sensitive paint varies inversely with absolute pressure. Consequently high signal-to-noise ratios are required to resolve aerodynamic pressure fields at low speeds, where the pressure variation around an object might only be a few percent of the mean pressure. This requirement is unavoidable, and implies that care must be taken to minimize noise sources present in the measurement. This paper discusses and compares the main noise sources in low speed PSP testing using the "classical" intensity-based single-luminophore technique. These are: temperature variation, model deformation, and lamp drift/paint degradation. Minimization of these error sources from the point of view of operation in production wind tunnels is discussed, with some examples from recent tests in NASA Ames facilities.

  8. Phase Retrieval Algorithm for Form Testing Metrology in Production Environment

    Directory of Open Access Journals (Sweden)

    Stephan Stuerwald

    2010-08-01

    Full Text Available Form testing interferometry permits a fast, non-tactile and full- field quantitative phase imaging of components in ultra precise manufacturing. To reduce the influence of vibrations under manufacturing conditions, it is most common to use the FT- based spatial carrier phase measurement technique (SCPM which requires only a single interferogram recording. The utilization of a generalized, relatively new spatial phase-shifting method operating in the position space opens up prospects for reduced phase noise and less reconstruction errors of the calculated phase-map under production conditions. Therefore this phase-shifting technique is investigated for applicability in machine integrated interferometric form testing of optical lenses. A characterization of the algorithm and a comparison with the commonly used FT-based algorithm is performed. As a reference, measurements are carried out with a coordinate measuring machine with nanometre accuracy.

  9. Future Food Production System Development Pulling from Space Biology Crop Growth Testing in Veggie

    Science.gov (United States)

    Massa, G. D.; Romeyn, M. W.; Fritsche, R. F.

    2017-01-01

    lessons, as we learn about growing at different scales and move toward developing systems that require less launch mass. Veggie will be used as a test bed for novel food production technologies. Veggie is a relatively simple precursor food production system but the knowledge gained from space biology validation tests in Veggie will have far reaching repercussions on future exploration food production.

  10. Ground Testing and Flight Demonstration of Charge Management of Insulated Test Masses Using UV LED Electron Photoemission

    CERN Document Server

    Saraf, Shailendhar; Balakrishnan, Karthik; Lui, Chin Yang; Soulage, Michael; Faied, Dohy; Hanson, John; Ling, Kuok; Jaroux, Belgacem; AlRashed, Abdullah; Nassban, Badr Al; Suwaidan, Badr Al; Harbi, Mohammed Al; Salamah, Badr Bin; Othman, Mohammed Bin; Qasim, Bandar Bin; DeBra, Daniel; Byer, Robert

    2016-01-01

    The UV LED mission demonstrates the precise control of the potential of electrically isolated test masses that is essential for the operation of space accelerometers and drag free sensors. Accelerometers and drag free sensors were and remain at the core of geodesy, aeronomy, and precision navigation missions as well as gravitational science experiments and gravitational wave observatories. Charge management using photoelectrons generated by the 254 nm UV line of Hg was first demonstrated on Gravity Probe B and is presently part of the LISA Pathfinder technology demonstration. The UV LED mission and prior ground testing demonstrates that AlGaN UV LEDs operating at 255 nm are superior to Mercury vapor lamps because of their smaller size, lower draw, higher dynamic range, and higher control authority. We show flight data from a small satellite mission on a Saudi Satellite that demonstrates AC charge control (UV LEDs and bias are AC modulated with adjustable relative phase) between a spherical test mass and its h...

  11. Testes mass, but not sperm length, increases with higher levels of polyandry in an ancient sex model.

    Directory of Open Access Journals (Sweden)

    David E Vrech

    Full Text Available There is strong evidence that polyandrous taxa have evolved relatively larger testes than monogamous relatives. Sperm size may either increase or decrease across species with the risk or intensity of sperm competition. Scorpions represent an ancient direct mode with spermatophore-mediated sperm transfer and are particularly well suited for studies in sperm competition. This work aims to analyze for the first time the variables affecting testes mass, ejaculate volume and sperm length, according with their levels of polyandry, in species belonging to the Neotropical family Bothriuridae. Variables influencing testes mass and sperm length were obtained by model selection analysis using corrected Akaike Information Criterion. Testes mass varied greatly among the seven species analyzed, ranging from 1.6 ± 1.1 mg in Timogenes dorbignyi to 16.3 ± 4.5 mg in Brachistosternus pentheri with an average of 8.4 ± 5.0 mg in all the species. The relationship between testes mass and body mass was not significant. Body allocation in testes mass, taken as Gonadosomatic Index, was high in Bothriurus cordubensis and Brachistosternus ferrugineus and low in Timogenes species. The best-fitting model for testes mass considered only polyandry as predictor with a positive influence. Model selection showed that body mass influenced sperm length negatively but after correcting for body mass, none of the variables analyzed explained sperm length. Both body mass and testes mass influenced spermatophore volume positively. There was a strong phylogenetic effect on the model containing testes mass. As predicted by the sperm competition theory and according to what happens in other arthropods, testes mass increased in species with higher levels of sperm competition, and influenced positively spermatophore volume, but data was not conclusive for sperm length.

  12. Testes mass, but not sperm length, increases with higher levels of polyandry in an ancient sex model.

    Science.gov (United States)

    Vrech, David E; Olivero, Paola A; Mattoni, Camilo I; Peretti, Alfredo V

    2014-01-01

    There is strong evidence that polyandrous taxa have evolved relatively larger testes than monogamous relatives. Sperm size may either increase or decrease across species with the risk or intensity of sperm competition. Scorpions represent an ancient direct mode with spermatophore-mediated sperm transfer and are particularly well suited for studies in sperm competition. This work aims to analyze for the first time the variables affecting testes mass, ejaculate volume and sperm length, according with their levels of polyandry, in species belonging to the Neotropical family Bothriuridae. Variables influencing testes mass and sperm length were obtained by model selection analysis using corrected Akaike Information Criterion. Testes mass varied greatly among the seven species analyzed, ranging from 1.6 ± 1.1 mg in Timogenes dorbignyi to 16.3 ± 4.5 mg in Brachistosternus pentheri with an average of 8.4 ± 5.0 mg in all the species. The relationship between testes mass and body mass was not significant. Body allocation in testes mass, taken as Gonadosomatic Index, was high in Bothriurus cordubensis and Brachistosternus ferrugineus and low in Timogenes species. The best-fitting model for testes mass considered only polyandry as predictor with a positive influence. Model selection showed that body mass influenced sperm length negatively but after correcting for body mass, none of the variables analyzed explained sperm length. Both body mass and testes mass influenced spermatophore volume positively. There was a strong phylogenetic effect on the model containing testes mass. As predicted by the sperm competition theory and according to what happens in other arthropods, testes mass increased in species with higher levels of sperm competition, and influenced positively spermatophore volume, but data was not conclusive for sperm length.

  13. A data base and a standard material for use in acceptance testing of low-activity waste products

    Energy Technology Data Exchange (ETDEWEB)

    Wolf, S.F.; Ebert, W.L.; Luo, J.S.; Strachan, D.M.

    1998-04-01

    The authors have conducted replicate dissolution tests following the product consistency test (PCT) procedure to measure the mean and standard deviation of the solution concentrations of B, Na, and Si at various combinations of temperature, duration, and glass/water mass ratio. Tests were conducted with a glass formulated to be compositionally similar to low-activity waste products anticipated for Hanford to evaluate the adequacy of test methods that have been designated in privatization contracts for use in product acceptance. An important finding from this set of tests is that the solution concentrations generated in tests at 20 C will likely be too low to measure the dissolution rates of waste products reliably. Based on these results, the authors recommend that the acceptance test be conducted at 40 C. Tests at 40 C generated higher solution concentrations, were more easily conducted, and the measured rates were easily related to those at 20 C. Replicate measurements of other glass properties were made to evaluate the possible use of LRM-1 as a standard material. These include its composition, homogeneity, density, compressive strength, the Na leachability index with the ANSI/ANS 16.1 leach test, and if the glass is characteristically hazardous with the toxicity characteristic leach procedure. The values of these properties were within the acceptable limits identified for Hanford low-activity waste products. The reproducibility of replicate tests and analyses indicates that the glass would be a suitable standard material.

  14. Modified Hodge Test: A Simple and Effective Test for Detection of Carbapenemase Production

    Directory of Open Access Journals (Sweden)

    N Malik

    2011-12-01

    Full Text Available Background and Objectives: Resistance among bacterial isolates is the leading cause of increased mortality and morbidity worldwide. Carbapenems once thought to be effective are becoming ineffective mostly due to the emergence of carbapenemase. This study was designed to determine in vitro efficacy of Modified Hodge test for detection of carbapenemase production in Gram negative rods.Material and Methods: The study was done in the Department of Microbiology, Armed Forces Institute of Pathology Rawalpindi Pakistan from January 2010 to December 2010. A total of 200 Gram negative rods from different clinical samples were taken. Those isolates which showed intermediate or susceptible zones i.e 16mm-21mm on disc diffusion were included in the study. These isolates were then subjected to Modified Hodge test.Result: Out of 200 isolates, 138 (69% were positive for carbapenemase production by Modified Hodge test. Out of 138 MHT positive organisms, the frequency of E. coli was 38%, followed by Pseudomonas aeruginosa (30%, Klebsiella pneumoniae (17%, Acinetobacter baumannii (12%, Citrobacter diversus (2% and Enterobacter agglomerans (1.4%.Conclusion: Modified Hodge test is a simple test which can be performed in the routine lab for detection of carbapenemases in isolates showing intermediate or sensitive zone diameter on disc diffusion.

  15. Application of multiple statistical tests to enhance mass spectrometry-based biomarker discovery

    Directory of Open Access Journals (Sweden)

    Garner Harold R

    2009-05-01

    Full Text Available Abstract Background Mass spectrometry-based biomarker discovery has long been hampered by the difficulty in reconciling lists of discriminatory peaks identified by different laboratories for the same diseases studied. We describe a multi-statistical analysis procedure that combines several independent computational methods. This approach capitalizes on the strengths of each to analyze the same high-resolution mass spectral data set to discover consensus differential mass peaks that should be robust biomarkers for distinguishing between disease states. Results The proposed methodology was applied to a pilot narcolepsy study using logistic regression, hierarchical clustering, t-test, and CART. Consensus, differential mass peaks with high predictive power were identified across three of the four statistical platforms. Based on the diagnostic accuracy measures investigated, the performance of the consensus-peak model was a compromise between logistic regression and CART, which produced better models than hierarchical clustering and t-test. However, consensus peaks confer a higher level of confidence in their ability to distinguish between disease states since they do not represent peaks that are a result of biases to a particular statistical algorithm. Instead, they were selected as differential across differing data distribution assumptions, demonstrating their true discriminatory potential. Conclusion The methodology described here is applicable to any high-resolution MALDI mass spectrometry-derived data set with minimal mass drift which is essential for peak-to-peak comparison studies. Four statistical approaches with differing data distribution assumptions were applied to the same raw data set to obtain consensus peaks that were found to be statistically differential between the two groups compared. These consensus peaks demonstrated high diagnostic accuracy when used to form a predictive model as evaluated by receiver operating characteristics

  16. The mass spectrum of the Schwinger model with matrix product states

    Energy Technology Data Exchange (ETDEWEB)

    Banuls, M.C.; Cirac, J.I. [Max-Planck-Institut fuer Quantenoptik (MPQ), Garching (Germany); Cichy, K. [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Poznan Univ. (Poland). Faculty of Physics; Jansen, K. [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Cyprus Univ., Nicosia (Cyprus). Dept. of Physics

    2013-07-15

    We show the feasibility of tensor network solutions for lattice gauge theories in Hamiltonian formulation by applying matrix product states algorithms to the Schwinger model with zero and non-vanishing fermion mass. We introduce new techniques to compute excitations in a system with open boundary conditions, and to identify the states corresponding to low momentum and different quantum numbers in the continuum. For the ground state and both the vector and scalar mass gaps in the massive case, the MPS technique attains precisions comparable to the best results available from other techniques.

  17. The mass spectrum of the Schwinger model with Matrix Product States

    CERN Document Server

    Bañuls, M C; Jansen, K; Cirac, J I

    2013-01-01

    We show the feasibility of tensor network solutions for lattice gauge theories in Hamiltonian formulation by applying matrix product states algorithms to the Schwinger model with zero and non-vanishing fermion mass. We introduce new techniques to compute excitations in a system with open boundary conditions, and to identify the states corresponding to low momentum and different quantum numbers in the continuum. For the ground state and both the vector and scalar mass gaps in the massive case, the MPS technique attains precisions comparable to the best results available from other techniques.

  18. Mass effects in the Higgs-gluon coupling: boosted vs. off-shell production

    OpenAIRE

    Buschmann, Malte; Gonçalves, Dorival; Kuttimalai, Silvan; Schönherr, Marek; Krauss, Frank; Plehn, Tilman

    2015-01-01

    In the upcoming LHC run we will be able to probe the structure ofthe loop--induced Higgs--gluon coupling through kinematics. First, we establish state-of-the-art simulations with up to two jets to next-to-leading order including top mass effects. They allow us to search for deviations from the low-energy limits in boosted Higgs production. In addition, the size of the top mass effects suggests that they should generally be included in Higgs studies at the LHC. Next, we show how off-shell Higg...

  19. The mass spectrum of the Schwinger model with matrix product states

    Energy Technology Data Exchange (ETDEWEB)

    Banuls, M.C.; Cirac, J.I. [Max-Planck-Institut fuer Quantenoptik (MPQ), Garching (Germany); Cichy, K. [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Poznan Univ. (Poland). Faculty of Physics; Jansen, K. [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Cyprus Univ., Nicosia (Cyprus). Dept. of Physics

    2013-07-15

    We show the feasibility of tensor network solutions for lattice gauge theories in Hamiltonian formulation by applying matrix product states algorithms to the Schwinger model with zero and non-vanishing fermion mass. We introduce new techniques to compute excitations in a system with open boundary conditions, and to identify the states corresponding to low momentum and different quantum numbers in the continuum. For the ground state and both the vector and scalar mass gaps in the massive case, the MPS technique attains precisions comparable to the best results available from other techniques.

  20. Intermediate Mass Dilepton Production in a Chemically Equilibrating Quark-Gluon Matter

    Institute of Scientific and Technical Information of China (English)

    HE Ze-Jun; ZHOU Wen-Jie; ZHANG Jia-Ju; LIU Bo

    2001-01-01

    Dilepton production during the chemical equilibration of quark-gluon matter with a finite baryon density has been studied. We find that due to the slowing down of the cooling rate and the high initial temperature of the quark-gluon matter produced at RHIC energies, the quark phase contribution to dileptons with intermediate masses is significantly heightened and is much larger than that calculated by the evolution of the thermodynamic equilibrium system. The latter has shown an enhancement of intermediate mass dileptons from the quark phase. Therefore, such an enhancement of dileptons should be a signature for quark-gluon matter formation.

  1. Single-top production in the s-channel and the top-quark mass

    CERN Document Server

    Alekhin, Sergey; Thier, Stephan

    2016-01-01

    We use a fixed-order expansion of resummed soft-gluon corrections to determine an approximate NNLO formula for the partonic cross section of single-top production in the $s$-channel. This formula is implemented in the program Hathor for the numerical evaluation of hadronic cross sections. With the resulting code, we perform a fit of the top-quark mass to Tevatron cross section data. Results for $m_t$ are given in the pole-mass scheme and in the $\\overline{\\mathrm{MS}}$ scheme.

  2. Assessment of the structure and variability of Weddell Sea water masses in distinct ocean reanalysis products

    Directory of Open Access Journals (Sweden)

    T. S. Dotto

    2014-02-01

    Full Text Available We assessed and evaluated the performance of five ocean reanalysis in reproducing essential hydrographic properties and their associated temporal variability for the Weddell Sea, Antarctica. The products used in this assessment were ECMWF ORAS4, CFSR, MyOcean UR025.4, ECCO2 and SODA. The present study focuses on the Weddell Sea deep layer, which is composed of the following three main water masses: Warm Deep Water (WDW, Weddell Sea Deep Water (WSDW and Weddell Sea Bottom Water (WSBW. Moreover, all the ocean reanalysis products analyzed showed limited capabilities in representing the surface water masses in the Weddell Sea. The MyOcean UR025.4 product provided the most accurate representation of the structure of the Weddell Sea water masses when compared to observations. The CFSR and ECCO2 products were not able to represent the WSBW throughout the simulation period. The expected WDW warming was only reproduced by the SODA product, while the ECCO2 product was able to represent the WSDW's hydrographic properties trends. All of these ocean reanalysis systems were able to represent the decrease in the WSBW's density. Our results also showed that a simple increase in horizontal resolution does not necessarily imply better representation of the deep layers. Rather, it is needed to observe the physics involved in each model and their parameterizations because the Southern Ocean suffers from the lack of in situ data, and it is biased by summer observations. The choice of the reanalysis product should be made carefully, taking into account the performance, the parameters of interest, and the type of physical processes to be evaluated.

  3. Liquid chromatography coupled to tandem mass spectrometry for the analysis of acrylamide in typical Spanish products.

    Science.gov (United States)

    Bermudo, E; Moyano, E; Puignou, L; Galceran, M T

    2008-07-15

    This paper describes the use of liquid chromatography coupled to tandem mass spectrometry for the determination of acrylamide in several typical foods produced and consumed in Spain. Christmas sweets, olives, traditionally made potato crisps, pastry products, sweet fritters ("churros") and one of Spain's most famous dishes, Spanish omelette, were selected. Using the mass spectra information provided by an ion trap analyzer in combination with the accurate mass measurements from time-of-flight (TOF) spectrometry a co-extractive interference present in some potato products was identified as valine. A porous graphitic carbon column, which enabled the co-extractive and acrylamide to be separated, and ion trap or triple quadrupole analyzers, depending on the acrylamide concentration, were used to determine this genotoxic compound in foodstuffs. The highest values were found in potato products, sweet fritters, Christmas sweets and pastry products, with values ranging between 70 and 2000 microg/g. Spanish omelette presented relatively low levels, similar to those obtained for dried fruits.

  4. Testing sub-gravitational forces on atoms from a miniature in-vacuum source mass

    Science.gov (United States)

    Jaffe, Matt; Haslinger, Philipp; Xu, Victoria; Hamilton, Paul; Upadhye, Amol; Elder, Benjamin; Khoury, Justin; Müller, Holger

    2017-10-01

    Traditional gravity measurements use bulk masses to both source and probe gravitational fields. Matter-wave interferometers enable the use of probe masses as small as neutrons, atoms and molecular clusters, but still require fields generated by masses ranging from hundreds of kilograms to the entire Earth. Shrinking the sources would enable versatile configurations, improve positioning accuracy, enable tests for beyond-standard-model (`fifth') forces, and allow observation of non-classical effects of gravity. Here we detect the gravitational force between freely falling caesium atoms and an in-vacuum, miniature (centimetre-sized, 0.19 kg) source mass using atom interferometry. Sensitivity down to gravitational strength forces accesses the natural scale for a wide class of cosmologically motivated scalar field models of modified gravity and dark energy. We improve the limits on two such models, chameleons and symmetrons, by over two orders of magnitude. We expect further tests of dark energy theories, and measurements of Newton's gravitational constant and the gravitational Aharonov-Bohm effect.

  5. Tinetti mobility test is related to muscle mass and strength in non-institutionalized elderly people.

    Science.gov (United States)

    Curcio, Francesco; Basile, Claudia; Liguori, Ilaria; Della-Morte, David; Gargiulo, Gaetano; Galizia, Gianluigi; Testa, Gianluca; Langellotto, Assunta; Cacciatore, Francesco; Bonaduce, Domenico; Abete, Pasquale

    2016-12-01

    Elderly people are characterized by a high prevalence of falls and sarcopenia. However, the relationship among Tinetti mobility test (TMT) score, a powerful tool to detect elderly people at risk of falls, and sarcopenia is still not thoroughly investigated. Thus, to determine the relationship between TMT score and muscle mass and strength, 337 elderly participants (mean age 77.1 ± 6.9 years) admitted to comprehensive geriatric assessment were enrolled. TMT score, muscle mass by bioimpedentiometer, and muscle strength by grip strength were evaluated. Muscle mass progressively decreased as TMT score decreased (from 15.3 ± 3.7 to 8.8 ± 1.8 kg/m(2); p for trend Tinetti score decreased (from 34.7 ± 8.0 to 23.7 ± 8.7 kg; p for trend 0.001). Linear regression analysis demonstrated that TMT score is linearly related with muscle mass (y = 4.5x + 0.4, r = 0.61; p score and muscle mass (r = 0.48, p = 0.024) and strength (r = 0.39, p = 0.046). The present study indicates that TMT score is significantly related to muscle mass and strength in non-institutionalized elderly participants. This evidence suggests that TMT score, together with evaluation of muscle mass and strength, may identify sarcopenic elderly participants at high risk of falls.

  6. Testing a scale-independent method to measure the mass of black holes

    CERN Document Server

    Gliozzi, M; Satyapal, S; Price, D M; Jang, I

    2011-01-01

    Estimating the black hole mass at the center of galaxies is a fundamental step not only for understanding the physics of accretion, but also for the cosmological evolution of galaxies. Recently a new method, based solely on X-ray data, was successfully applied to determine the black hole mass in Galactic systems. Since X-rays are thought to be produced via Comptonization process both in stellar and supermassive black holes, in principle, the same method may be applied to estimate the mass in supermassive black holes. In this work we test this hypothesis by performing a systematic analysis of a sample of AGNs, whose black hole mass has been already determined via reverberation mapping and which possess high quality XMM-Newton archival data. The good agreement obtained between the black hole masses derived with this novel scaling technique and the reverberation mapping values suggests that this method is robust and works equally well on stellar and supermassive black holes, making it a truly scale-independent t...

  7. Study of parametric instability in gravitational wave detectors with silicon test masses

    Science.gov (United States)

    Zhang, Jue; Zhao, Chunnong; Ju, Li; Blair, David

    2017-03-01

    Parametric instability is an intrinsic risk in high power laser interferometer gravitational wave detectors, in which the optical cavity modes interact with the acoustic modes of the mirrors, leading to exponential growth of the acoustic vibration. In this paper, we investigate the potential parametric instability for a proposed next generation gravitational wave detector, the LIGO Voyager blue design, with cooled silicon test masses of size 45 cm in diameter and 55 cm in thickness. It is shown that there would be about two unstable modes per test mass at an arm cavity power of 3 MW, with the highest parametric gain of  ∼76. While this is less than the predicted number of unstable modes for Advanced LIGO (∼40 modes with max gain of  ∼32 at the designed operating power of 830 kW), the importance of developing suitable instability suppression schemes is emphasized.

  8. Measuring test mass acceleration noise in space-based gravitational wave astronomy

    CERN Document Server

    Congedo, Giuseppe

    2014-01-01

    The basic constituent of interferometric gravitational wave detectors -- the test mass to test mass interferometric link -- behaves as a differential dynamometer measuring effective differential forces, comprising an integrated measure of gravity curvature, inertial effects, as well as non-gravitational spurious forces. This last contribution is going to be characterised by the LISA Pathfinder mission, a technology precursor of future space-borne detectors like eLISA. Changing the perspective from displacement to acceleration can benefit the data analysis of LISA Pathfinder and future detectors. The response in differential acceleration to gravitational waves is derived for a space-based detector's interferometric link. The acceleration formalism can also be integrated into time delay interferometry by building up the unequal-arm Michelson differential acceleration combination. The differential acceleration is nominally insensitive to the system free evolution dominating the slow displacement dynamics of low-...

  9. Project Rio Blanco: additional production testing and reservoir analysis

    Energy Technology Data Exchange (ETDEWEB)

    Ballou, L.B.

    1976-11-01

    Additional subsurface investigations of the Rio Blanco detonation region and adjacent reservoir have been underway since the last technical meeting at IAEA. The lowermost explosion cavity has been reentered and a production test from it was performed. A dry gas volume of 7.6 x 10/sup 5/ m/sup 3/ (27 Mmscf) was withdrawn. Chemical and radiochemical analyses of this gas show that (1) the yield of the bottom explosive was 31 +- 2 kt; (2) the cavity/chimney volume was 2.4 x 10/sup 4/ m/sup 3/ (8.4 x 10/sup 5/ ft/sup 3/); (3) about 7 percent of the tritium produced is associated with the gas; and (4) a slight (approximately 0.1 percent) gas contribution from the middle explosion region was noted. The reservoir/chimney model implies an unstimulated reservoir flow capacity of 0.15 mdarcy-m (0.50 md-ft) connected to the bottom chimney region. A cavity radius of 21 +- 3 m (70 +- 10 ft) was deduced. Unstimulated reservoir production parameters were investigated in a well offset 190 m (625 ft) from the emplacement hole. Insufficient productivity was obtained in the Mesaverde formation (in which the bottom explosive was detonated) to evaluate reservoir properties. The productive sandstones in the Fort Union formation adjoining the top detonation region were individually evaluated. Their aggregate flow capacity was determined to be 0.14 +- 0.2 mdarcy-m (0.45 +- 0.08 md-ft). A numerical simulation model which incorporates these data is described. The lack of a high-permeability connection between the three explosion regions remains unexplained. The two chimney reentry wells have been cemented to the surface and abandoned. The offset well has been plugged in a way which preserves the option for additional subsurface investigation in the future. Project facilities have been removed and the site restored to conditions which minimize environmental impact.

  10. Study on Testing the Composition of Indoor Air Pollution to Benzene Series by Laser Mass Spectrometry

    Institute of Scientific and Technical Information of China (English)

    XUE Mei; HE Le-min; ZHONG Wei-gang; ZHAO Xin; LI Xiu-zhen

    2014-01-01

    This paper reports some experimental detecting results of pollutants in the atmosphere by means of laser mass spectrometry. For toluene as calibration gas, the calibration procedure was also given. Benzene, toluene and xylene were discovered in testing indoor atmosphere resulting from dope in the course of fitment. Meanwhile, it is noticeable that the concentration of various harmful elements is obviously decreasing as time goes on.

  11. Holographic ballistic gravimeter with the fixation of the angular position of a test mass

    Science.gov (United States)

    Dmitriev, A. L.; Kotova, E. I.; Nagibin, Yu. T.

    2016-10-01

    We have reported on the results of an experimental simulation of a holographic absolute ballistic gravimeter with the minimal (down to 0.5 mm) length of the trajectory of a falling test mass and rigid stabilization of its angular position. Gravimeters of this type ensure the mobile measurement of the free fall acceleration and are intended for the application in a new field of research, i.e., HF gravimetry.

  12. Construction of an Ultrahigh Pressure Liquid Chromatography-Tandem Mass Spectral Library of Plant Natural Products and Comparative Spectral Analyses.

    Science.gov (United States)

    Lei, Zhentian; Jing, Li; Qiu, Feng; Zhang, Hua; Huhman, David; Zhou, Zhiqin; Sumner, Lloyd W

    2015-07-21

    A plant natural product tandem mass spectral library has been constructed using authentic standards and purified compounds. Currently, the library contains 1734 tandem mass spectra for 289 compounds, with the majority (76%) of the compounds being plant phenolics such as flavonoids, isoflavonoids, and phenylpropanoids. Tandem mass spectra and chromatographic retention data were acquired on a triple quadrupole mass spectrometer coupled to an ultrahigh pressure liquid chromatograph using six different collision energies (CEs) (10-60 eV). Comparative analyses of the tandem mass spectral data revealed that the loss of ring substituents preceded the C-ring opening during the fragmentation of flavonoids and isoflavonoids. At lower CE (i.e., 10 and 20 eV), the flavonoids and isoflavonoid central ring structures typically remained intact, and fragmentation was characterized by the loss of the substituents (i.e., methyl and glycosyl groups). At higher CE, the flavonoid and isoflavonoid core ring systems underwent C-ring cleavage and/or rearrangement depending on the structure, particularly hydroxylation patterns. In-source electrochemical oxidation was observed for phenolics that had ortho-diphenol moieties (i.e., vicinal hydroxyl groups on the aromatic rings). The ortho-diphenols were oxidized to ortho-quinones, yielding an intensive and, in most cases, a base ion peak corresponding to a [(M - 2H) - H](-) ion in their mass spectra. The library also contains reverse-phase retention times, allowing for the construction, validation, and testing of an artificial neural network retention prediction of other flavonoids and isoflavonoids not contained within the library. The library is freely available for nonprofit, academic use and it can be downloaded at http://www.noble.org/apps/Scientific/WebDownloadManager/DownloadArea.aspx.

  13. Simulation of ASTROD I test mass charging due to solar energetic particles

    CERN Document Server

    Liu, Lei; Ni, Wei-Tou; Shaul, D N A

    2007-01-01

    As ASTROD I travels through space, its test mass will accrue charge due to galactic cosmic-rays and solar energetic particles incident on the spacecraft. This test mass charge will result in Coulomb forces between the test mass and the surrounding electrodes. In earlier work using the GEANT4 toolkit, we predicted a net charging rate of nearly 9.0 +e/s from cosmic-ray protons between 0.1 and 1000 GeV at solar maximum, and rising to 26.5 +e/s at solar minimum. Here we use GEANT4 to simulate the charging process due to solar energetic particle events and to estimate the magnitude of acceleration noise due to this charging. The predicted charging rates range from 2840 to 64300 +e/s, at peak intensity, for the 4 largest SEP events in September and October 1989. For the 2 larger events, the acceleration disturbances due to charging exceeds the ASTROD I acceleration noise budget requirement. Continuous discharge should be considered for suppressing this charging noise. The acceleration noise during the 2 small event...

  14. On the mechanical quality factors of cryogenic test masses from fused silica and crystalline quartz

    CERN Document Server

    Schroeter, Anja; Schnabel, Roman; Reid, Stuart; Martin, Iain; Rowan, Sheila; Schwarz, Christian; Koettig, Torsten; Neubert, Ralf; Thürk, Matthias; Vodel, Wolfgang; Tünnermann, Andreas; Danzmann, Karsten; Seidel, Paul

    2007-01-01

    Current interferometric gravitational wave detectors (IGWDs) are operated at room temperature with test masses made from fused silica. Fused silica shows very low absorption at the laser wavelength of 1064 nm. It is also well suited to realize low thermal noise floors in the detector signal band since it offers low mechanical loss, i. e. high quality factors (Q factors) at room temperature. However, for a further reduction of thermal noise, cooling the test masses to cryogenic temperatures may prove an interesting technique. Here we compare the results of Q factor measurements at cryogenic temperatures of acoustic eigenmodes of test masses from fused silica and its crystalline counterpart. Our results show that the mechanical loss of fused silica increases with lower temperature and reaches a maximum at 30 K for frequencies of slightly above 10 kHz. The losses of crystalline quartz generally show lower values and even fall below the room temperature values of fused silica below 10 K. Our results show that in ...

  15. Higgs boson pair production: Top quark mass effects at NLO and NNLO

    Directory of Open Access Journals (Sweden)

    Jonathan Grigo

    2015-11-01

    Full Text Available We compute next-to-next-to-leading order QCD corrections to the gluon-induced production cross section of Higgs boson pairs in the large top quark mass limit using the soft-virtual approximation. In the limit of infinitely-heavy top quark we confirm the results in the literature. We add two more expansion terms in the inverse top quark mass to the Mt→∞ result. Since the 1/Mt expansion converges poorly, we try to improve on it by factorizing the exact leading order cross section. We discuss two ways of doing that and conclude that the finite top quark mass effects shift the cross section at most by about 10% at next-to-leading order and by about 5% at next-to-next-to-leading order.

  16. Identification of hemoglobin variants by top-down mass spectrometry using selected diagnostic product ions.

    Science.gov (United States)

    Coelho Graça, Didia; Hartmer, Ralf; Jabs, Wolfgang; Beris, Photis; Clerici, Lorella; Stoermer, Carsten; Samii, Kaveh; Hochstrasser, Denis; Tsybin, Yury O; Scherl, Alexander; Lescuyer, Pierre

    2015-04-01

    Hemoglobin disorder diagnosis is a complex procedure combining several analytical steps. Due to the lack of specificity of the currently used protein analysis methods, the identification of uncommon hemoglobin variants (proteoforms) can become a hard task to accomplish. The aim of this work was to develop a mass spectrometry-based approach to quickly identify mutated protein sequences within globin chain variants. To reach this goal, a top-down electron transfer dissociation mass spectrometry method was developed for hemoglobin β chain analysis. A diagnostic product ion list was established with a color code strategy allowing to quickly and specifically localize a mutation in the hemoglobin β chain sequence. The method was applied to the analysis of rare hemoglobin β chain variants and an (A)γ-β fusion protein. The results showed that the developed data analysis process allows fast and reliable interpretation of top-down electron transfer dissociation mass spectra by nonexpert users in the clinical area.

  17. Standard test methods for determining chemical durability of nuclear, hazardous, and mixed waste glasses and multiphase glass ceramics: The product consistency test (PCT)

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2002-01-01

    1.1 These product consistency test methods A and B evaluate the chemical durability of homogeneous glasses, phase separated glasses, devitrified glasses, glass ceramics, and/or multiphase glass ceramic waste forms hereafter collectively referred to as “glass waste forms” by measuring the concentrations of the chemical species released to a test solution. 1.1.1 Test Method A is a seven-day chemical durability test performed at 90 ± 2°C in a leachant of ASTM-Type I water. The test method is static and conducted in stainless steel vessels. Test Method A can specifically be used to evaluate whether the chemical durability and elemental release characteristics of nuclear, hazardous, and mixed glass waste forms have been consistently controlled during production. This test method is applicable to radioactive and simulated glass waste forms as defined above. 1.1.2 Test Method B is a durability test that allows testing at various test durations, test temperatures, mesh size, mass of sample, leachant volume, a...

  18. Mass spectrometry analysis of etch products from CR-39 plastic irradiated by heavy ions

    Science.gov (United States)

    Kodaira, S.; Nanjo, D.; Kawashima, H.; Yasuda, N.; Konishi, T.; Kurano, M.; Kitamura, H.; Uchihori, Y.; Naka, S.; Ota, S.; Ideguchi, Y.; Hasebe, N.; Mori, Y.; Yamauchi, T.

    2012-09-01

    As a feasibility study, gas chromatography-mass spectrometry (GC-MS) and matrix-assisted laser desorption ionization-mass spectrometry (MALDI-MS) have been applied to analyze etch products of CR-39 plastic (one of the most frequently used solid states nuclear track detector) for the understanding of track formation and etching mechanisms by heavy ion irradiation. The etch products of irradiated CR-39 dissolved in sodium hydroxide solution (NaOH) contain radiation-induced fragments. For the GC-MS analysis, we found peaks of diethylene glycol (DEG) and a small but a definitive peak of ethylene glycol (EG) in the etch products from CR-39 irradiated by 60 MeV N ion beams. The etch products of unirradiated CR-39 showed a clear peak of DEG, but no other significant peaks were found. DEG is known to be released from the CR-39 molecule as a fragment by alkaline hydrolysis reaction of the polymer. We postulate that EG was formed as a result of the breaking of the ether bond (C-O-C) of the DEG part of the CR-39 polymer by the irradiation. The mass distribution of polyallylalcohol was obtained from the etch products from irradiated and unirradiated CR-39 samples by MALDI-MS analysis. Polyallylalcohol, with the repeating mass interval of m/z = 58 Da (dalton) between m/z = 800 and 3500, was expected to be produced from CR-39 by alkaline hydrolysis. We used IAA as a matrix to assist the ionization of organic analyte in MALDI-MS analysis and found that peaks from IAA covered mass spectrum in the lower m/z region making difficult to identify CR-39 fragment peaks which were also be seen in the same region. The mass spectrometry analysis using GC-MS and MALDI-MS will be powerful tools to investigate the radiation-induced polymeric fragments and helping to understand the track formation mechanism in CR-39 by heavy ions.

  19. Optimization of Production Medium for Mass Culture of Metarhizium anisopliae ARS 2231

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Seung Woo [Korea University, Seoul (Korea); Moon, Ki Hyuk [Kyungwon University Technology Complex, Songnam (Korea); Yoon, Jeong Weon [Suwon University, Suwon (Korea)

    1999-11-01

    Chemical pesticides which have been commonly used for crop protection have many problems such as high production cost and environmental hazards. Entomogeneous fungi which attack living insects are very powerful means for microbiological insecticide. The purpose of this study is to investigate the culture conditions for mass production of Metarhizium anisopliae ARS 2231 which is a potential microbiological pesticide. The temperature and pH range for optimal cultivation were 28 deg. C and pH 5.0-7.0, respectively. For M. anisopliae ARS 2231, 3.0% (w/v) rice bran, 0.8% (w/v) hydrolyzed casein, and 0.3% (w/v) K{sub 2}HPO{sub 4} were found as the proper nutrients, considering cell mass, enzyme activities, and spore concentration. 16 refs., 10 tabs.

  20. Chemical vapor deposition of carbon nanotubes: a review on growth mechanism and mass production.

    Science.gov (United States)

    Kumar, Mukul; Ando, Yoshinori

    2010-06-01

    This review article deals with the growth mechanism and mass production of carbon nanotubes (CNTs) by chemical vapor deposition (CVD). Different aspects of CNT synthesis and growth mechanism are reviewed in the light of latest progresses and understandings in the field. Materials aspects such as the roles of hydrocarbon, catalyst and catalyst support are discussed. Many new catalysts and new carbon sources are described. Growth-control aspects such as the effects of temperature, vapor pressure and catalyst concentration on CNT diameter distribution and single- or multi-wall formation are explained. Latest reports of metal-catalyst-free CNT growth are considered. The mass-production aspect is discussed from the perspective of a sustainable CNT technology. Existing problems and challenges of the process are addressed with future directions.

  1. Sharing and community curation of mass spectrometry data with Global Natural Products Social Molecular Networking

    DEFF Research Database (Denmark)

    Wang, Mingxun; Carver, Jeremy J.; Pevzner, Pavel

    2016-01-01

    The potential of the diverse chemistries present in natural products (NP) for biotechnology and medicine remains untapped because NP databases are not searchable with raw data and the NP community has no way to share data other than in published papers. Although mass spectrometry (MS) techniques...... are well-suited to high-throughput characterization of NP, there is a pressing need for an infrastructure to enable sharing and curation of data. We present Global Natural Products Social Molecular Networking (GNPS; http://gnps.ucsd.edu), an open-access knowledge base for community-wide organization...... and sharing of raw, processed or identified tandem mass (MS/MS) spectrometry data. In GNPS, crowdsourced curation of freely available community-wide reference MS libraries will underpin improved annotations. Data-driven social-networking should facilitate identification of spectra and foster collaborations...

  2. Mass Transfer of Corrosion Products in the Nonisothermal Sodium Loop of a Fast Reactor

    Science.gov (United States)

    Varseev, E. V.; Alekseev, V. V.

    2014-11-01

    The mass transfer of the products of corrosion of the steel surface of the sodium loop of a fast nuclear power reactor was investigated for the purpose of optimization of its parameters. The problem of deposition of the corrosion products on the surface of the heat-exchange unit of the indicated loop was considered. Experimental data on the rate of accumulation of deposits in the channel of this unit and results of the dispersion analysis of the suspensions contained in the sodium coolant are presented.

  3. Experimental characterization of airflow, heat and mass transfer in a cold room filled with food products

    OpenAIRE

    Duret, S.; Hoang, H. -M.; Flick, Denis; Laguerre, O.

    2014-01-01

    Temperature and moisture heterogeneity, with non-uniform airflow in cold rooms was observed in several studies. This heterogeneity can lead to a deterioration of food quality and safety. Heat and mass transfer in cold rooms is a complex phenomenon because of the presence of the product (airflow modification, heat of respiration.) and the coupling between heat transfer and airflow. Temperature, velocity, humidity and heat transfer coefficient measurements were carried out in a ventilated cold ...

  4. High mass resolution time of flight mass spectrometer for measuring products in heterogeneous catalysis in highly sensitive microreactors

    DEFF Research Database (Denmark)

    Andersen, Thomas; Jensen, Robert; Christensen, M. K.

    2012-01-01

    response. Gas analysis is performed with a time of flight mass spectrometer with a modified nude Bayard-Alpert ionization gauge as gas ionization source. The mass resolution of the time of flight mass spectrometer using the ion gauge as ionization source is estimated to m∕Δm > 2500. The system design...

  5. Iodox process tests in a transuranium element production campaign

    Energy Technology Data Exchange (ETDEWEB)

    Collins, E. D.; Benker, D. E.

    1979-06-01

    The Iodox process, an advanced method for removing gaseous radioiodine from airstreams, was tested at high activity levels during transuranium element production operations. Special equipment was used to remove radioiodine from 3-5M HNO/sub 3/ dissolver solutions by volatilization and to absorb the iodine from the dissolver off-gas into hyperazeotropic HNO/sub 3/. More than 96% of the /sup 131/I in the dissolver solutions was removed by heeating to 100/sup 0/C and air-sparging. Treatments such as boiling, sparging with 5% N/sub 2/O/sub 3/, and adjustment to 10/sup -4/ M KI or 1% H/sub 2/O/sub 2/ effected the additional removal of /sup 131/I by factors of 2 to 5. Other than /sup 131/I, no fission products were volatilized during the treatments. A six-stage bubble-cap column was used for the abosrpttion. Off-gas decontamination factors were in the range of 1 x 10/sup 4/ to 8 x 10/sub 4/, or 5 to 7 per stage; these values are similar to those obtained during previous low-activity studies.

  6. Improving Quality of Seal Leak Test Product using Six Sigma

    Science.gov (United States)

    Luthfi Malik, Abdullah; Akbar, Muhammad; Irianto, Dradjad

    2016-02-01

    Seal leak test part is a polyurethane material-based product. Based on past data, defect level of this product was 8%, higher than the target of 5%. Quality improvement effort was done using six sigma method that included phases of define, measure, analyse, improve, and control. In the design phase, a Delphi method was used to identify factors that were critical to quality. In the measure phase, stability and process capability was measured. Fault tree analysis (FTA) and failure mode and effect analysis (FMEA) were used in the next phase to analize the root cause and to determine the priority issues. Improve phase was done by compiling, selecting, and designing alternative repair. Some improvement efforts were identified, i.e. (i) making a checklist for maintenance schedules, (ii) making written reminder form, (iii) modifying the SOP more detail, and (iv) performing a major service to the vacuum machine. To ensure the continuity of improvement efforts, some control activities were executed, i.e. (i) controlling, monitoring, documenting, and setting target frequently, (ii) implementing reward and punishment system, (iii) adding cleaning tool, and (iv) building six sigma organizational structure.

  7. Power production experiments at the Test Beam Line in the CLIC Test Facility 3

    CERN Document Server

    Lillestøl, Reidar Lunde; Adli, Erik; Lundheim, Lars Magne

    2010-01-01

    CLIC is an international study of a future multi-TeV electron-positron linear collider, where the energy of a high-intensity drive beam is extracted and transferred to the main beam via Power Extraction and Transfer Structures (PETS) in the form of rf power. The study of power production is therefore essential for the feasibility of CLIC. Power production in PETS has been studied, and ex- periments have been performed in the decelerator Test Beam Line in the CLIC Test Facility 3. In particular, the correlation of the power production and the beam position inside the structure has been studied. It is shown that the total produced power is constant when the beam has a position offset through the PETS. In addition, the difference between the measured phases from each side is independent of the beam position, which allows for efficient combination of the fields. However, the ratio of the power on each side of the PETS unexpectedly shows a linear dependence on the horizontal offset, with a correlation value of 0.8...

  8. New product testing and the utilization of user expertise: Evidence from the Pharmaceutical industry

    OpenAIRE

    Smed, Marie; Salomo, Søren; Schultz, Carsten; Getz, Kenneth A.

    2012-01-01

    A significant and often neglected obstacle in new product development is the testing and approval process in the late stages of development. The testing process has primarily been observed as an in-house decision process, however, in many industries products undergo extensive testing before market launch where external stakeholders play a key role. Users are often integrated in testing of new product candidates, and supply valuable knowledge to developers by testing the new product in natural...

  9. Vadose Zone VOC Mass Transfer Testing At The SRS Miscellaneous Chemical Basin

    Energy Technology Data Exchange (ETDEWEB)

    Riha, B

    2005-10-30

    loading rates to groundwater. These metrics will aid in answering the question ''How clean is protective of the environment''? For this study, a field test was developed to measure a mass transfer factor by injecting clean air into the subsurface through a sample port or well and measuring the rebound VOC concentration over time. Interpretation of the he results of these tests will provide a mass transfer rate that will be used to determine the appropriate type of SVE for the area (passive, enhanced or active SVE), a measured field parameter to estimate mass loading to the groundwater, and time frame for cleanup.

  10. Expanding analytical options in sports drug testing: Mass spectrometric detection of prohibited substances in exhaled breath.

    Science.gov (United States)

    Thevis, Mario; Krug, Oliver; Geyer, Hans; Schänzer, Wilhelm

    2017-08-15

    Continuously refining and advancing the strategies and methods employed in sports drug testing is critical for efficient doping controls. Besides improving and expanding the spectrum of target analytes, alternative test matrices have warranted in-depth evaluation as they commonly allow for minimal-/non-invasive and non-intrusive sample collection. In this study, the potential of exhaled breath (EB) as doping control specimen was assessed. EB collection devices employing a non-woven electret-based air filter unit were used to generate test specimens, simulating a potential future application in doping controls. A multi-analyte sports drug testing approach configured for a subset of 12 model compounds that represent specific classes of substances prohibited in sports (anabolic agents, hormone and metabolic modulators, stimulants, and beta-blockers) was established using unispray liquid chromatography/tandem mass spectrometry (LC/MS/MS) and applied to spiked and elimination study EB samples. The test method was characterized concerning specificity, assay imprecision, and limits of detection. The EB collection device allowed for retaining and extracting all selected model compounds from the EB aerosol. Following elution and concentration, LC/MS/MS analysis enabled detection limits between 5 and 100 pg/filter and imprecisions ranging from 3% to 20% for the 12 selected model compounds. By means of EB samples from patients and participants of administration studies, the elimination of relevant compounds and, thus, their traceability in EB for doping control purposes, was investigated. Besides stimulants such as methylhexaneamine and pseudoephedrine, also the anabolic-androgenic steroid dehydrochloromethyltestosterone, the metabolic modulator meldonium, and the beta-blocker bisoprolol was detected in exhaled breath. The EB aerosol has provided a promising proof-of-concept suggesting the expansion of this testing strategy as a complement to currently utilized sports drug

  11. A hybrid approach to urine drug testing using high-resolution mass spectrometry and select immunoassays.

    Science.gov (United States)

    McMillin, Gwendolyn A; Marin, Stephanie J; Johnson-Davis, Kamisha L; Lawlor, Bryan G; Strathmann, Frederick G

    2015-02-01

    The major objective of this research was to propose a simplified approach for the evaluation of medication adherence in chronic pain management patients, using liquid chromatography time-of-flight (TOF) mass spectrometry, performed in parallel with select homogeneous enzyme immunoassays (HEIAs). We called it a "hybrid" approach to urine drug testing. The hybrid approach was defined based on anticipated positivity rates, availability of commercial reagents for HEIAs, and assay performance, particularly analytical sensitivity and specificity for drug(s) of interest. Subsequent to implementation of the hybrid approach, time to result was compared with that observed with other urine drug testing approaches. Opioids, benzodiazepines, zolpidem, amphetamine-like stimulants, and methylphenidate metabolite were detected by TOF mass spectrometry to maximize specificity and sensitivity of these 37 drug analytes. Barbiturates, cannabinoid metabolite, carisoprodol, cocaine metabolite, ethyl glucuronide, methadone, phencyclidine, propoxyphene, and tramadol were detected by HEIAs that performed adequately and/or for which positivity rates were very low. Time to result was significantly reduced compared with the traditional approach. The hybrid approach to urine drug testing provides a simplified and analytically specific testing process that minimizes the need for secondary confirmation. Copyright© by the American Society for Clinical Pathology.

  12. Test Sample for the Spatially Resolved Quantification of Illicit Drugs on Fingerprints Using Imaging Mass Spectrometry.

    Science.gov (United States)

    Muramoto, Shin; Forbes, Thomas P; van Asten, Arian C; Gillen, Greg

    2015-01-01

    A novel test sample for the spatially resolved quantification of illicit drugs on the surface of a fingerprint using time-of-flight secondary ion mass spectrometry (ToF-SIMS) and desorption electrospray ionization mass spectrometry (DESI-MS) was demonstrated. Calibration curves relating the signal intensity to the amount of drug deposited on the surface were generated from inkjet-printed arrays of cocaine, methamphetamine, and heroin with a deposited-mass ranging nominally from 10 pg to 50 ng per spot. These curves were used to construct concentration maps that visualized the spatial distribution of the drugs on top of a fingerprint, as well as being able to quantify the amount of drugs in a given area within the map. For the drugs on the fingerprint on silicon, ToF-SIMS showed great success, as it was able to generate concentration maps of all three drugs. On the fingerprint on paper, only the concentration map of cocaine could be constructed using ToF-SIMS and DESI-MS, as the signals of methamphetamine and heroin were completely suppressed by matrix and substrate effects. Spatially resolved quantification of illicit drugs using imaging mass spectrometry is possible, but the choice of substrates could significantly affect the results.

  13. Optimization of a flat plate glass reactor for mass production of Nannochloropsis sp. outdoors.

    Science.gov (United States)

    Richmond, A; Cheng-Wu, Z

    2001-02-23

    The relationships between areal (g m(-2) per day) and volumetric (g l(-1) per day) productivity of Nannochloropsis sp. as affected by the light-path (ranging from 1.3 to 17.0 cm) of a vertical flat plate glass photobioreactor were elucidated. In general, the shorter the length of the light-path (LP), the smaller the areal volume and the higher the volumetric productivity. The areal productivity in relation to the light-path, in contrast, yielded an optimum curve, the highest areal productivity was obtained in a 10 cm LP reactor, which is regarded, therefore, optimal for mass production of Nannochloropsis. An attempt was made to identify criteria by which to assess the efficiency of a photobioreactor in utilizing strong incident energy. Two basic factors which relate to reactor efficiency and its cost-effectiveness have been defined as (a) the total illuminated surface required to produce a set quantity of product and (b) culture volume required to produce that quantity. As a general guide line, the lower these values are, the more efficient and cost-effective the reactor would be. An interesting feature of this analysis rests with the fact that an open raceways is as effective in productivity per illuminated area as a flat-plate reactor with an optimal light path, both cultivation systems requiring ca. 85 m(2) of illuminated surface to produce 1 kg dry cell mass of Nannochloropsis sp. per day. The difference in light utilization efficiency between the two very different production systems involves three aspects - first, the open raceway requires ca. 6 times greater volume than the 10 cm flat plate reactor to produce the same quantity of cell-mass. Second, the total ground area (i.e. including the ground area between reactors) for the vertical flat plate reactor is less than one half of that occupied by an open raceway, indicating the former is more efficient, photosynthetically, compared with the latter. Finally, the harvested cell density is close to one order of

  14. Dilepton production as a useful probe of quark gluon plasma with temperature dependent chemical potential quark mass

    Science.gov (United States)

    Kumar, Yogesh; Singh, S. Somorendro

    2016-07-01

    We extend the previous study of dilepton production using [S. Somorendro Singh and Y. Kumar, Can. J. Phys. 92 (2014) 31] based on a simple quasiparticle model of quark-gluon plasma (QGP). In this model, finite value of quark mass uses temperature dependent chemical potential the so-called Temperature Dependent Chemical Potential Quark Mass (TDCPQM). We calculate dilepton production in the relevant range of mass region. It is observed that the production rate is marginally enhanced from the earlier work. This is due to the effect of TDCPQM and its effect is highly significant in the production of dilepton.

  15. A modified triple test for palpable breast masses: the value of ultrasound and core needle biopsy.

    Science.gov (United States)

    Wai, Christina J; Al-Mubarak, Ghada; Homer, Marc J; Goldkamp, Allison; Samenfeld-Specht, Marja; Lee, Yoojin; Logvinenko, Tanya; Rothschild, Janice G; Graham, Roger A

    2013-03-01

    The original triple test score (TTS)--clinical examination, mammogram, and fine-needle aspiration (FNA) biopsy--has long been used to evaluate palpable breast masses. We modified the original TTS to include ultrasound (US) and core biopsy to determine their role in evaluating palpable breast masses. A retrospective chart review of 320 female patients was performed. We developed a modified triple test score (mTTS) that included physical examination, mammogram and/or US, and FNA and/or core biopsy. For the examination and imaging score, 1-3 points were given for low, moderate, or high suspicion. Biopsy scores were characterized as benign, atypical, or malignant. Final outcome was determined by open biopsy or follow-up greater than 1 year. Physical examination was 92% accurate (95% confidence interval [CI] 0.89-0.96, p core biopsy changed the scores of 24 patients; only three changed clinical management. For patients with a palpable breast mass and a mTTS score of 3-4, no further assessment is necessary. Those with a mTTS of 8-9 can proceed to definitive therapy. Patients with a mTTS of 5-7 require further assessment. US and/or core biopsy added little to the accuracy or predictive value of the original TTS.

  16. A new class of equivalence principle test masses, with application to SR-POEM

    Science.gov (United States)

    Reasenberg, Robert D.

    2014-09-01

    We describe a new class of test masses (TMs) for use in a Galilean test of the equivalence principle, principally in space. These TMs have n\\geqslant 2 vertical bars that are joined by an off-center connector. A pair of TMs will be positioned to have interleaved bars. For n\\geqslant 3, the principal moments of inertia of a TM can be made equal. With their centers of mass aligned, a TM pair shows decreasing susceptibility to differential acceleration from local mass as n increases. For the Sounding Rocket based Principle Of Equivalence Measurement (SR-POEM), the mission requirements are well met with n=3, but not met with n=2. For a 1 kg SR-POEM TM, vibration frequencies can be made to be above 1 kHz and thus not interfere with the operation of the TM suspension system. The SR-POEM housing supports electrodes for a set of capacitance gauges that observes all six kinematic degrees of freedom of each TM.

  17. Temperature effects on mass-scaling exponents in colonial animals: a manipulative test.

    Science.gov (United States)

    Barneche, Diego R; White, Craig R; Marshall, Dustin J

    2017-01-01

    Body size and temperature are fundamental drivers of ecological processes because they determine metabolic rates at the individual level. Whether these drivers act independently on individual-level metabolic rates remains uncertain. Most studies of intraspecific scaling of unitary organisms must rely on preexisting differences in size to examine its relationship with metabolic rate, thereby potentially confounding size-correlated traits (e.g., age, nutrition) with size, which can affect metabolic rate. Here, we use a size manipulation approach to test whether metabolic mass scaling and temperature dependence interact in four species (two phyla) of colonial marine invertebrates. Size manipulation in colonial organisms allows tests of how ecological processes (e.g., predation) affect individual physiology and consequently population- and community-level energy flux. Body mass and temperature interacted in two species, with one species exhibiting decreased and the other increased mass-scaling exponents with increasing temperature. The allometric scaling of metabolic rate that we observe in three species contrasts with the isometric scaling of ingestion rates observed in some colonial marine invertebrates. Thus, we suggest that the often observed competitive superiority of colonial over unitary organisms may arise because the difference between energy intake and expenditure increases more strongly with size in colonial organisms.

  18. Distortion-Product Otoacoustic Emission Test Performance for Ototoxicity Monitoring

    Science.gov (United States)

    Reavis, Kelly M.; McMillan, Garnett; Austin, Donald; Gallun, Frederick; Fausti, Stephen A.; Gordon, Jane S.; Helt, Wendy J.; Konrad-Martin, Dawn

    2017-01-01

    Introduction A nonbehavioral method for monitoring ototoxicity in patients treated with cisplatin is needed because patients enduring chemotherapy may not be well or cooperative enough to undergo repeated hearing tests. Distortion-product otoacoustic emissions (DPOAEs) provide a nonbehavioral measure of auditory function that is sensitive to cisplatin exposure. However, interpreting DPOAE findings in the context of ototoxicity monitoring requires that their accuracy be determined in relation to a clinically accepted gold standard test. Objectives Among patients receiving cisplatin for the treatment of cancer, we sought to (1) identify the combination of DPOAE metrics and ototoxicity risk factors that best classified ears with and without ototoxic-induced hearing changes; and (2) evaluate the test performance achieved by the composite measure as well as by DPOAEs alone. Design Odds of experiencing hearing changes at a given patient visit were determined using data collected prospectively from 24 Veterans receiving cisplatin. Pure-tone thresholds were examined within an octave of each subject’s high-frequency hearing limit. DPOAE were collected as a set of four response growth (input/output) functions near the highest f2 frequency that yielded a robust response at L2 = L1 = 65 dB SPL. Logistic regression modeled the risk of hearing change using several DPOAE metrics, drug treatment factors, and other patient factors as independent variables. An optimal discriminant function was derived by reducing the model so that only statistically significant variables were included. Receiver operating characteristic curve analyses were used to evaluate test performance. Results At higher cisplatin doses, ears with better hearing at baseline were more likely to exhibit ototoxic hearing changes than those with poorer hearing. Measures of pre-exposure hearing, cumulative drug dose, and DPOAEs generated a highly accurate discriminant function with a cross-validated area under the

  19. How body mass and lifestyle affect juvenile biomass production in placental mammals.

    Science.gov (United States)

    Sibly, Richard M; Grady, John M; Venditti, Chris; Brown, James H

    2014-02-22

    In mammals, the mass-specific rate of biomass production during gestation and lactation, here called maternal productivity, has been shown to vary with body size and lifestyle. Metabolic theory predicts that post-weaning growth of offspring, here termed juvenile productivity, should be higher than maternal productivity, and juveniles of smaller species should be more productive than those of larger species. Furthermore because juveniles generally have similar lifestyles to their mothers, across species juvenile and maternal productivities should be correlated. We evaluated these predictions with data from 270 species of placental mammals in 14 taxonomic/lifestyle groups. All three predictions were supported. Lagomorphs, perissodactyls and artiodactyls were very productive both as juveniles and as mothers as expected from the abundance and reliability of their foods. Primates and bats were unproductive as juveniles and as mothers, as expected as an indirect consequence of their low predation risk and consequent low mortality. Our results point the way to a mechanistic explanation for the suite of correlated life-history traits that has been called the slow-fast continuum.

  20. Productivity of Enewetak Atoll reef flats predicted from mass transfer relationships

    Science.gov (United States)

    Atkinson, M. J.

    1992-07-01

    The productivity of a coral reef flat at Enewetak Atoll is calculated by assuming phosphate (P) uptake is mass transfer limited, and then scaling P uptake to carbon (C) fixation. The approach is to treat the coral reef flat as a rough surface in fully-developed turbulent flow. Input parameters to the equations are water velocity, depth, roughness height of the reef, P concentration and the C:P ratio of autotrophs. A 9-day continuous record of water velocity and depth over the windward reef flats of Enewetak Atoll is used to compare an estimate of productivity from the model to the measured productivity. The calculated productivity is 542 ± 79mmol C m -2 day -1 and the measured productivity is 500 mmol C m -2 day -1. Although there are few experiments to verify empirical scaling of engineering equations to reef communities, these results indicate that neither alternative external supplies of P, nor biological mechanisms of recycling appear to be required to support the high areal productivity of the Enewetak reef flats. A high flow rate of tropical surface water across reef flats can account for the elevated productivity of these communities.

  1. Test mass charging simulation of ASTROD I due to solar energetic particles at 0.5 AU

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Maintaining the geodesic motion of the test mass is vital to ASTROD I space mission. However,the electrostatic charging of the test mass due to cosmic rays and solar energetic particles will result in Coulomb and Lorentz forces and consequently influence the test mass motions. To estimate the size of these effects,a credible simulation of test mass charging processes is critically required. Using the GEANT4 software toolkit,we have modeled the charging processes and predict how the ASTROD I test mass will charge positively at a rate of 217370 e + /s,due to solar energetic particles(SEPs) at~0.5 AU caused by the largest SEPs event on 29,September,1989. In addition to Monte Carlo uncertainty,an error of ±30% in the net charging rates was added to account for uncertainties in the spectra,physics and geometry models.

  2. Syringe test screening of microbial gas production activity: Cases denitrification and biogas formation.

    Science.gov (United States)

    Østgaard, Kjetill; Kowarz, Viktoria; Shuai, Wang; Henry, Ingrid A; Sposob, Michal; Haugen, Hildegunn Hegna; Bakke, Rune

    2017-01-01

    Mass produced plastic syringes may be applied as vessels for cheap, simple and large scale batch culture testing. As illustrated for the cases of denitrification and of biogas formation, metabolic activity was monitored by direct reading of the piston movement due to the gas volume formed. Pressure buildup due to friction was shown to be moderate. A piston pull and slide back routine can be applied before recording gas volume to minimize experimental errors due to friction. Inoculum handling and activity may be conveniently standardized as illustrated by applying biofilm carriers. A robust set of positive as well as negative controls ("blanks") should be included to ensure quality of the actual testing. The denitrification test showed saturation response at increasing amounts of inoculum in the form of adapted moving bed biofilm reactor (MBBR) carriers, with well correlated nitrate consumption vs. gas volume formed. As shown, the denitrification test efficiently screened different inocula at standardized substrates. Also, different substrates were successfully screened and compared at standardized inocula. The biogas potential test showed efficient screening of different substrates with effects of relative amounts of carbohydrate, protein, fat. A second case with CO2 capture reclaimer waste as substrate demonstrated successful use of co-feeding to support waste treatment and how temperature effects on kinetics and stoichiometry can be observed. In total, syringe test screening of microbial gas production seems highly efficient at a low cost when properly applied. Copyright © 2016 Elsevier B.V. All rights reserved.

  3. Time-bound product returns and optimal order quantities for mass merchandisers

    Science.gov (United States)

    Yu, Min-Chun; Goh, Mark

    2012-01-01

    The return guidelines for a mass merchandiser usually entail a grace period, a markdown on the original price and the condition of the returned items. This research utilises eight scenarios formed from the variation of possible return guidelines to model the cost functions of single-product categories for a typical mass merchandiser. Models for the eight scenarios are developed and solved with the objective of maximising the expected profit so as to obtain closed form solutions for the associated optimal order quantity. An illustrative example and sensitivity analysis are provided to demonstrate the applicability of the model. Our results show that merchandisers who allow for returns within a time window, albeit with a penalty cost imposed and the returned products being recoverable, should plan for larger order amounts as such products do not affect the business. Similarly, the merchandisers who allow for returns beyond a grace period and without any penalty charges, but where the returned products are irrecoverable, should manage their stocks in this category more judiciously by ordering as little as possible so as to limit the number of returns and carefully consider the effects of their customer satisfaction-guaranteed policies, if any.

  4. Characterization of the limonene oxidation products with liquid chromatography coupled to the tandem mass spectrometry

    Science.gov (United States)

    Witkowski, Bartłomiej; Gierczak, Tomasz

    2017-04-01

    Composition of the secondary organic aerosol (SOA) generated during ozonolysis of limonene was investigated with liquid chromatography coupled to the negative electrospray ionization (ESI), quadrupole tandem mass spectrometry (MS/MS) as well as high resolution Time-of-Flight mass spectrometry. Aerosol was generated in the flow-tube reactor. HR-MS/MS analysis allowed for proposing structures for the several up-to-date unknown limonene oxidation products. In addition to the low MW limonene oxidation products, significant quantities of oligomers characterized by elemental compositions: C19H30O5, C18H28O6, C19H28O7, C19H30O7 and C20H34O9 were detected in the SOA samples. It was concluded that these compounds are most likely esters, aldol reaction products and/or hemiacetals. In addition to detailed study of the limonene oxidation products, the reaction time as well as initial ozone concentration impact on the limonene SOA composition was investigated. The relative intensities of the two esters of the limonic acid and 7-hydroxy limononic acid increased as a result of lowering the initial ozone concentration and shortening the reaction time, indicating that esterification may be an important oligomerization pathway during limonene SOA formation.

  5. Materials Combustion Testing and Combustion Product Sensor Evaluations in FY12

    Science.gov (United States)

    Meyer, Marit Elisabeth; Mudgett, Paul D.; Hornung, Steven D.; McClure, Mark B.; Pilgrim, Jeffrey S.; Bryg, Victoria; Makel, Darby; Ruff, Gary A.; Hunter, Gary

    2013-01-01

    NASA Centers continue to collaborate to characterize the chemical species and smoke particles generated by the combustion of current space-rated non-metallic materials including fluoropolymers. This paper describes the results of tests conducted February through September 2012 to identify optimal chemical markers both for augmenting particle-based fire detection methods and for monitoring the post-fire cleanup phase in human spacecraft. These studies follow up on testing conducted in August 2010 and reported at ICES 2011. The tests were conducted at the NASA White Sands Test Facility in a custom glove box designed for burning fractional gram quantities of materials under varying heating profiles. The 623 L chamber was heavily instrumented to quantify organics (gas chromatography/mass spectrometry), inorganics by water extraction followed by ion chromatography, and select species by various individual commercially-available sensors. Evaluating new technologies for measuring carbon monoxide, hydrogen cyanide, hydrogen fluoride, hydrogen chloride and other species of interest was a key objective of the test. Some of these sensors were located inside the glovebox near the fire source to avoid losses through the sampling lines; the rest were located just outside the glovebox. Instruments for smoke particle characterization included a Tapered Element Oscillating Microbalance Personal Dust Monitor (TEOM PDM) and a TSI Dust Trak DRX to measure particle mass concentration, a TSI PTrak for number concentration and a thermal precipitator for collection of particles for microscopic analysis. Materials studied included Nomex®, M22759 wire insulation, granulated circuit board, polyvinyl chloride (PVC), Polytetrafluoroethylene (PTFE), Kapton®, and mixtures of PTFE and Kapton®. Furnace temperatures ranged from 340o to 640o C, focusing on the smoldering regime. Of particular interest in these tests was confirming burn repeatability and production of acid gases with different

  6. Materials Combustion Testing and Combustion Product Sensor Evaluations in FY12

    Science.gov (United States)

    Meyer, Marit E.; Hunter, Gary; Ruff, Gary; Mudgett, Paul D.; Hornung, Steven D.; McClure, Mark B.; Pilgrim, Jeffrey S.; Bryg, Victoria; Makel, Darby

    2013-01-01

    NASA Centers continue to collaborate to characterize the chemical species and smoke particles generated by the combustion of current space-rated non-metallic materials including fluoropolymers. This paper describes the results of tests conducted February through September 2012 to identify optimal chemical markers both for augmenting particle-based fire detection methods and for monitoring the post-fire cleanup phase in human spacecraft. These studies follow up on testing conducted in August 2010 and reported at ICES 2011. The tests were conducted at the NASA White Sands Test Facility in a custom glove box designed for burning fractional gram quantities of materials under varying heating profiles. The 623 L chamber was heavily instrumented to quantify organics (gas chromatography/mass spectrometry), inorganics by water extraction followed by ion chromatography, and select species by various individual commercially-available sensors. Evaluating new technologies for measuring carbon monoxide, hydrogen cyanide, hydrogen fluoride, hydrogen chloride and other species of interest was a key objective of the test. Some of these sensors were located inside the glovebox near the fire source to avoid losses through the sampling lines; the rest were located just outside the glovebox. Instruments for smoke particle characterization included a Tapered Element Oscillating Microbalance Personal Dust Monitor (TEOM PDM) and a TSI Dust Trak DRX to measure particle mass concentration, a TSI PTrak for number concentration and a thermal precipitator for collection of particles for microscopic analysis. Materials studied included Nomex(R), M22759 wire insulation, granulated circuit board, polyvinyl chloride (PVC), Polytetrafluoroethylene (PTFE), Kapton(R), and mixtures of PTFE and Kapton(R). Furnace temperatures ranged from 340 to 640 C, focusing on the smoldering regime. Of particular interest in these tests was confirming burn repeatability and production of acid gases with different

  7. Fabrication and testing of the recoil mass spectrometer at Bombay Pelletron

    Indian Academy of Sciences (India)

    S Nagaraj; H C Jain; P K Joshi; S D Paul; R Palit; H V Panchal; B S Naidu; A Chatterjee; A Navin

    2001-07-01

    A recoil mass spectrometer (RMS) has been designed, fabricated and installed at the 15°S beam-line of the Pelletron at TIFR. The RMS consists of a quadrupole doublet just after the target chamber followed by an ‘electrostatic deflector’, a magnetic dipole and a second electrostatic deflector. The recoils produced in the 12C+58Ni reaction using 60 MeV 12C beam were focussed with the help of electric and magnetic fields and detected in a strip detector placed at the focal plane of the RMS. Further testing of the spectrometer to obtain mass resolution and efficiency are in progress.

  8. Standard test methods for chemical, mass spectrometric, and spectrochemical analysis of nuclear-grade boron carbide

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2004-01-01

    1.1 These test methods cover procedures for the chemical, mass spectrometric, and spectrochemical analysis of nuclear-grade boron carbide powder and pellets to determine compliance with specifications. 1.2 The analytical procedures appear in the following order: Sections Total Carbon by Combustion and Gravimetry 7-17 Total Boron by Titrimetry 18-28 Isotopic Composition by Mass Spectrometry 29-38 Chloride and Fluoride Separation by Pyrohydrolysis 39-45 Chloride by Constant-Current Coulometry 46-54 Fluoride by Ion-Selective Electrode 55-63 Water by Constant-Voltage Coulometry 64-72 Impurities by Spectrochemical Analysis 73-81 Soluble Boron by Titrimetry 82-95 Soluble Carbon by a Manometric Measurement 96-105 Metallic Impurities by a Direct Reader Spectrometric Method 106-114

  9. Advantages and Challenges of Dried Blood Spot Analysis by Mass Spectrometry Across the Total Testing Process

    Science.gov (United States)

    Zakaria, Rosita; Allen, Katrina J.; Koplin, Jennifer J.; Roche, Peter

    2016-01-01

    Introduction Through the introduction of advanced analytical techniques and improved throughput, the scope of dried blood spot testing utilising mass spectrometric methods, has broadly expanded. Clinicians and researchers have become very enthusiastic about the potential applications of dried blood spot based mass spectrometric applications. Analysts on the other hand face challenges of sensitivity, reproducibility and overall accuracy of dried blood spot quantification. In this review, we aim to bring together these two facets to discuss the advantages and current challenges of non-newborn screening applications of dried blood spot quantification by mass spectrometry. Methods To address these aims we performed a key word search of the PubMed and MEDLINE online databases in conjunction with individual manual searches to gather information. Keywords for the initial search included; “blood spot” and “mass spectrometry”; while excluding “newborn”; and “neonate”. In addition, databases were restricted to English language and human specific. There was no time period limit applied. Results As a result of these selection criteria, 194 references were identified for review. For presentation, this information is divided into: 1) clinical applications; and 2) analytical considerations across the total testing process; being pre-analytical, analytical and post-analytical considerations. Conclusions DBS analysis using MS applications is now broadly applied, with drug monitoring for both therapeutic and toxicological analysis being the most extensively reported. Several parameters can affect the accuracy of DBS measurement and further bridge experiments are required to develop adjustment rules for comparability between dried blood spot measures and the equivalent serum/plasma values. Likewise, the establishment of independent reference intervals for dried blood spot sample matrix is required. PMID:28149263

  10. Left Ventricular Wall Stress-Mass-Heart Rate Product and Cardiovascular Events in Treated Hypertensive Patients

    DEFF Research Database (Denmark)

    Devereux, Richard B; Bang, Casper N; Roman, Mary J;

    2015-01-01

    In the Losartan Intervention for End Point Reduction in Hypertension (LIFE) study, 4.8 years' losartan- versus atenolol-based antihypertensive treatment reduced left ventricular hypertrophy and cardiovascular end points, including cardiovascular death and stroke. However, there was no difference...... randomized treatment, the triple product was reduced more by atenolol, with prevalences of elevated triple product of 39% versus 51% on losartan (both P≤0.001). In Cox regression analyses adjusting for age, smoking, diabetes mellitus, and prior stroke, MI, and heart failure, 1 SD lower triple product...... was associated with 23% (95% confidence interval 13%-32%) fewer composite end points, 31% (18%-41%) less cardiovascular mortality, 30% (15%-41%) lower MI, and 22% (11%-33%) lower all-cause mortality (all P≤0.001), without association with stroke (P=0.34). Although losartan-based therapy reduced ventricular mass...

  11. Test elements of direct sums and free products of free Lie algebras

    Indian Academy of Sciences (India)

    Cennet Eskal; Naime Ekici

    2016-02-01

    We give a characterization of test elements of a direct sum of free Lie algebras in terms of test elements of the factors. In addition, we construct certain types of test elements and we prove that in a free product of free Lie algebras, product of the homogeneous test elements of the factors is also a test element.

  12. Comparative Study of Professional vs Mass Market Topical Products for Treatment of Facial Photodamage.

    Science.gov (United States)

    Reich, Hilary; Wallander, Irmina; Schulte, Lacie; Goodier, Molly; Zelickson, Brian

    2016-01-01

    Many over the counter topical products claim to reverse the signs of cutaneous photo-damage. To date, the two most studied ingredients for improving the texture, tone, and pigmentation of the skin are topical retinoids and hydroquinone. This split face study compares a mass market skincare regimen with a prescription skin care regimen for improvement in photo damaged skin. Twenty-seven subjects with moderate photo damaged facial skin were enrolled. Each subject was consented and assigned with the mass market anti-aging system (Treatment A) to one side of the face and the prescription anti-aging system (Treatment B or Treatment C) to the other side of the face. Treatment B contained 13 subjects whom did not use 0.025% Retinol cream. Treatment C contained 14 subjects who used a 0.025% Retinol Cream. Subjects had 4 visits over 12 weeks for digital photography and surveys. Photographs were evaluated by blinded physicians. Physician objective analysis showed all three systems to have a statistically significant clinical improvement in photoaged skin seen in as little as 4 weeks of use. Participant's surveys rated the mass market system higher than both of the professional systems for visible skin changes, ease of use, and likelihood to recommend to a friend. Twelve of twenty-seven subjects preferred the mass market system for overall improvement while twelve thought each system gave the same improvement. This study demonstrates that a mass marketed skin care system can give similar clinical improvements in photo-aged skin as a professionally dispensed prescription system and the majority of participants preferred the mass-marketed system.

  13. Direct electrospray tandem mass spectrometry of the unstable hydroperoxy bishemiacetal product derived from cholesterol ozonolysis.

    Science.gov (United States)

    Pulfer, Melissa K; Harrison, Kathleen; Murphy, Robert C

    2004-02-01

    Cholesterol is the most abundant neutral lipid in the epithelial lining fluid of the lower airways of the lung also known as pulmonary surfactant and a potential target for reaction with ambient ozone when inspired into the human lung. The isolated double bond of cholesterol has been shown to be susceptible to attack by ozone, but the major reaction product from cholesterol ozonolysis had been remarkably difficult to structurally characterize. Recently, NMR and X-ray crystallography have been used to suggest the formation of a hydroperoxy, hydroxy hemiacetal product, using various derivatives and models of cholesterol to stabilize this chemically reactive product. Electrospray ionization mass spectrometry was used to study the somewhat unstable ozonolysis product of cholesterol which was found to display unique ionization and fragmentation properties when collisionally activated. The electron-deficient carbon atoms of this highly oxygenated product permitted covalent attachment of an acetate anion during negative ion electrospray ionization, leading to the formation of abundant adduct ions at m/z 511. Surprisingly, positive ions were not readily formed. Collision induced dissociation of the adduct anion yielded a major ion at m/z 477, corresponding to the loss of hydrogen peroxide. The most abundant fragment ion following collisional activation was observed at m/z 93, resulting from a complex rearrangement subsequent to the attack of the hydroperoxide anion on the carbon center of the acetate adduct. Based on the interpretation of the tandem mass spectral data, the major cholesterol ozonization product was characterized as a hydroperoxy, hydroxy hemiacetal derivative, which was consistent with the NMR and X-ray crystallographic studies which were carried out on the more stable methyl ether derivative.

  14. Fabrication and testing history prototypes and production units

    Energy Technology Data Exchange (ETDEWEB)

    1954-09-01

    From April, 1951 to Aug, 1954, New York Shipbuilding Corp. carried out a subcontract with E.I. du Pont de Nemours & Company that was without parallel in the shipyard`s history. The work, designated the NYX Project for reasons of security, was vital to the operations of the Savannah River Plant, Aiken, S.C., which was then being designed and constructed by du Pont for the Atomic Energy Commission. It consisted of three broad parts: developmental and experimental work; fabrication and testing of a prototype unit; fabrication of production units. Five production units were ultimately built, one of them converted from the prototype. All were fabricated from stainless steel, and involved welding techniques, control of thermal distortion and tolerances never previously attempted on assemblies of comparable size. Du Pont`s technical experience and the background of New York Ship in heavy construction, particularly in the fabrication of naval gun turrets, were combined from the outset to resolve the difficult fabrication problems that occurred almost daily. Representatives of both companies worked together as a team in the shops and at supervisory levels to an unprecedented extent. The report is intended primarily to summarize New York Ship`s part in the project, but also includes some of du Pont`s activities since the work of the two organizations was so interrelated. Because of the scope of the program, it will not always be possible to provide detailed information, but rather to record what happened in general terms. Where the reader desires more specific data, he should refer to original plans and records, including various reports compiled during the course of the project.

  15. Field testing of lake water chemistry with a portable and an AUV-based mass spectrometer.

    Science.gov (United States)

    Hemond, Harry F; Mueller, Amy V; Hemond, Michael

    2008-10-01

    Two mass spectrometers (MS) are tested for the measurement of volatile substances, such as hydrocarbons and metabolic gases, in natural waters. KOALA is a backpackable MS operated from above the water surface, in which samples are pumped through a flow cell using a syringe. NEREUS is an underwater instrument hosted by an autonomous underwater vehicle (AUV) that is linked to a communications network to provide chemical data in real time. The mass analyzers of the two MS are nearly identical cycloids, and both use flat-plate membrane inlets. Testing took place in an eutrophic, thermally stratified lake exhibiting steep chemical gradients and significant levels of methane. KOALA provided rapid multispecies analysis of dissolved gases, with a detection limit for methane of 0.1 ppm (readily extendable to 0.01 ppm) and savings of time of at least a factor of 10 compared to that of conventional analysis. The AUV-mounted NEREUS additionally provided rapid spatial coverage and the capability of performing chemical surveys autonomously. Tests demonstrated the need for temperature control of a membrane inlet when steep thermal gradients are present in a water body, as well as the benefits of co-locating all sensors on the AUV to avoid interference from chemically different waters entering and draining from the free-flooding outer hull. The ability to measure dissolved volatiles provided by MS offers potential for complementarity with ionic sensors in the study of natural waters, such as in the case of the carbonate system.

  16. Jet activity as a probe of high-mass resonance production

    Energy Technology Data Exchange (ETDEWEB)

    Harland-Lang, L.A. [University College London, Department of Physics and Astronomy, London (United Kingdom); Khoze, V.A. [Durham University, Institute for Particle Physics Phenomenology, Durham (United Kingdom); NRC Kurchatov Institute, Petersburg Nuclear Physics Institute, St. Petersburg (Russian Federation); Ryskin, M.G. [NRC Kurchatov Institute, Petersburg Nuclear Physics Institute, St. Petersburg (Russian Federation); Spannowsky, M. [Durham University, Institute for Particle Physics Phenomenology, Durham (United Kingdom)

    2016-11-15

    We explore the method of using the measured jet activity associated with a high-mass resonance state to determine the corresponding production modes. To demonstrate the potential of the approach, we consider the case of a resonance of mass M{sub R} decaying to a diphoton final state. We perform a Monte Carlo study, considering three mass points M{sub R} = 0.75, 1.5, 2.5 TeV, and show that the γγ, WW, gg and light and heavy q anti q initiated cases lead to distinct predictions for the jet multiplicity distributions. As an example, we apply this result to the ATLAS search for resonances in diphoton events, using the 2015 data set of 3.2 fb{sup -1} at √(s) = 13 TeV. Taking the spin-0 selection, we demonstrate that a dominantly gg-initiated signal hypothesis is mildly disfavoured, while the γγ and light quark cases give good descriptions within the limited statistics, and a dominantly WW-initiated hypothesis is found to be in strong tension with the data. We also comment on the b anti b initial state, which can already be constrained by the measured b-jet multiplicity. Finally, we present expected exclusion limits with integrated luminosity, and demonstrate that with just a few 10s of fb{sup -1} we can expect to constrain the production modes of such a resonance. (orig.)

  17. Production of dosage forms for oral drug delivery by laminar extrusion of wet masses.

    Science.gov (United States)

    Müllers, Katrin C; Wahl, Martin A; Pinto, João F

    2013-08-01

    Laminar extrusion of wet masses was studied as a novel technology for the production of dosage forms for oral drug delivery. Extrusion was carried out with a ram extruder. Formulations contained either microcrystalline cellulose (MCC) or dicalcium phosphate (DCP) as diluent, hydroxypropyl methylcellulose (HPMC), lactose, and water. Extrudates were characterized for their tensile strength, Young's modulus of elasticity, water absorption, gel forming capacity, and release of two model drugs, coumarin (COU) and propranolol hydrochloride (PRO). Cohesive extrudates could be produced with both filling materials (MCC and DCP) when HPMC was included as a binder at low amounts (3.3-4.5% w/w dry weight). Employing more HPMC, the elasticity of the wet masses increased which resulted in distinct surface defects. For MCC, the maximum HPMC amount that could be included in the formulations (15% w/w dry weight) did not affect the mechanical properties or decrease the drug release significantly. For DCP extrudates, the maximally effective HPMC amount was 30% (w/w dry weight) with influence on both the mechanical properties and drug release. This study suggests that laminar extrusion of wet masses is a feasible technique for the production of dosage forms for oral drug delivery.

  18. INVESTIGATION OF THE RELATIONSHIP OF THE STATISTICAL MOMENTS OF THE FAT PHASE MASS DISTRIBUTION AND RELAXATION SPECTRA OF DAIRY PRODUCTS

    Directory of Open Access Journals (Sweden)

    V. E. Merzlikin

    2015-01-01

    Full Text Available The article deals with the search for optimal parameter estimation of the parameters of the process of homogenization of dairy products. Provides a theoretical basis for relationship of the relaxation time of the fat globules and attenuation coefficient of ultrasonic oscillations in dairy products. Suggested from the measured acoustic properties of milk to make the calculations of the mass distribution of fat globules. Studies on the proof of this hypothesis. Morphological analysis procedure carried out for homogenized milk samples at different pressures, as well as homogenized. As a result of research obtained distribution histogram of fat globules in dependence on the homogenization pressure. Also performed acoustic studies to obtain the frequency characteristics of loss modulus as a function of homogenization pressure. For further research the choice of method for approximating dependences is obtained using statistical moments of distributions. The parameters for the approximation of the distribution of fat globules and loss modulus versus pressure homogenization were obtained. Was carried out to test the hypothesis on the relationship parameters of approximation of the distribution of the fat globules and loss modulus as a function of pressure homogenization. Correlation analysis showed a clear dependence of the first and second statistical moment distributions of the pressure homogenization. The obtain ed dependence is consistent with the physical meaning of the first two moments of a statistical distribution. Correlation analysis was carried out according to the statistical moments of the distribution of the fat globules from moments of loss modulus. It is concluded that the possibility of ultrasonic testing the degree of homogenization and mass distribution of the fat globules of milk products.

  19. Mass identification of the neutral products generated in the plasma treatment of polluted atmospheres

    Science.gov (United States)

    Seymour, David

    2013-09-01

    Plasmas produced using Dielectric Barrier Discharge (DBD) devices are very effective in the abatement of air pollution resulting from, for example, the emission of volatile organic compounds (VCOs) by a range of industrial and agricultural processes. The development and monitoring of effective DBD systems can be investigated by advanced mass spectrometric methods specifically configured for analysis at high and atmospheric pressures The present work involves the operation of a small DBD reactor which uses either a helium or nitrogen carrier gas to sustain the plasma to which may be added reactive gases, such as oxygen, as well as samples of pollutants such as chlorinated hydrocarbons, including trichloroethylene. The mass spectrometric analysis was performed using a specially configured system manufactured by Hiden Analytical Ltd. The DBD source may also be combined with a catalyst for plasma-enhanced catalysis. The neutral products of the reactions proceeding in the plasma at atmospheric pressure are sampled through the capillary sampling system which also reduces the pressure of the gas mixture delivered to the ionisation source of the quadrupole mass spectrometer. The ions produced are subsequently mass identified. We describe typical data and comment on the advantages of this technique.

  20. New product testing and the utilization of user expertise: Evidence from the Pharmaceutical industry

    DEFF Research Database (Denmark)

    Smed, Marie; Salomo, Søren; Schultz, Carsten

    2012-01-01

    A significant and often neglected obstacle in new product development is the testing and approval process in the late stages of development. The testing process has primarily been observed as an in-house decision process, however, in many industries products undergo extensive testing before market...... generated by users in product testing. Further, the important user network in high-tech product testing may likely be globally dispersed, and the mean of communicating between user and producer in the testing process are therefore tested. A dataset of 395 site-representatives are applied to study...... launch where external stakeholders play a key role. Users are often integrated in testing of new product candidates, and supply valuable knowledge to developers by testing the new product in natural business settings. As especially high-tech products are closely linked to related services and usage...

  1. Chemical Characterization and Reactivity Testing of Fuel-Oxidizer Reaction Product (Test Report)

    Science.gov (United States)

    1996-01-01

    The product of incomplete reaction of monomethylhydrazine (MMH) and nitrogen tetroxide (NTO) propellants, or fuel-oxidizer reaction product (FORP), has been hypothesized as a contributory cause of an anomaly which occurred in the chamber pressure (PC) transducer tube on the Reaction Control Subsystem (RCS) aft thruster 467 on flight STS-51. A small hole was found in the titanium-alloy PC tube at the first bend below the pressure transducer. It was surmised that the hole may have been caused by heat and pressure resulting from ignition of FORP. The NASA Johnson Space Center (JSC) White Sands Test Facility (WSTF) was requested to define the chemical characteristics of FORP, characterize its reactivity, and simulate the events in a controlled environment which may have lead to the Pc-tube failure. Samples of FORP were obtained from the gas-phase reaction of MMH with NTO under laboratory conditions, the pulsed firings of RCS thrusters with modified PC tubes using varied oxidizer or fuel lead times, and the nominal RCS thruster firings at WSTF and Kaiser-Marquardt. Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), accelerating rate calorimetry (ARC), ion chromatography (IC), inductively coupled plasma (ICP) spectrometry, thermogravimetric analysis (TGA) coupled to FTIR (TGA/FTIR), and mechanical impact testing were used to qualitatively and quantitatively characterize the chemical, thermal, and ignition properties of FORP. These studies showed that the composition of FORP is variable but falls within a limited range of compositions that depends on the fuel loxidizer ratio at the time of formation, composition of the post-formation atmosphere (reducing or oxidizing), and reaction or postreaction temperature. A typical composition contains methylhydrazinium nitrate (MMHN), ammonium nitrate (AN), methylammonium nitrate (MAN), and trace amounts of hydrazinium nitrate and 1,1-dimethylhydrazinium nitrate. The thermal decomposition

  2. Evaluation of Primary Production in the Lower Amazon River Based on a Dissolved Oxygen Stable Isotopic Mass Balance

    Energy Technology Data Exchange (ETDEWEB)

    Gagne-Maynard, William C.; Ward, Nicholas D.; Keil, Richard G.; Sawakuchi, Henrique O.; Da Cunha, Alan C.; Neu, Vania; Brito, Daimio C.; Da Silva Less, Diani F.; Diniz, Joel E. M.; De Matos Valerio, Aline; Kampel, Milton; Krusche, Alex V.; Richey, Jeffrey E.

    2017-02-07

    The Amazon River outgasses nearly an equivalent amount of CO2 as the rainforest sequesters on an annual basis due to microbial decomposition of terrigenous and aquatic organic matter. Most research performed in the Amazon has been focused on unraveling the mechanisms driving CO2 production since the recognition of a persistent state of CO2 supersaturation. However, although the river system is clearly net heterotrophic, the interplay between primary production and respiration is an essential aspect to understanding the overall metabolism of the ecosystem and potential transfer of energy up trophic levels. For example, an efficient ecosystem is capable of both decomposing high amounts of organic matter at lower trophic levels, driving CO2 emissions, and accumulating energy/biomass in higher trophic levels, stimulating fisheries production. Early studies found minimal evidence for primary production in the Amazon River mainstem and it has since been assumed that photosynthesis is strongly limited by low light penetration attributed to the high sediment load. Here, we test this assumption by measuring the stable isotopic composition of O218O-O2) and O2 saturation levels in the lower Amazon River from Óbidos to the river mouth and its major tributaries, the Xingu and Tapajós rivers, during high and low water periods. An oxygen mass balance model was developed to estimate the input of photosynthetic oxygen in the discrete reach from Óbidos to Almeirim, midway to the river mouth. Based on the oxygen mass balance we estimate that primary production occurred at a rate of 0.39 ± 0.24 g O m3 d-1 at high water and 1.02 ± 0.55 g O m3 d-1 at low water. This translates to 41 ± 24% of the rate of O2 drawdown via respiration during high water and 67 ± 33% during low water. These primary production rates are 2-7 times higher than

  3. Tests of Environmental Effects on Type Ia Supernova Production

    Science.gov (United States)

    Sadler, Suzanna M.; Strolger, L.; Wolff, S.

    2011-01-01

    The host galaxy environments of type Ia supernovae (SNe Ia) provide our best opportunity for constraining the mechanism(s) of the SN Ia progenitor system, i.e., the stars involved, the incubation times, and the sensitivity of SNe Ia to changes in the local gas-phase metallicity. The latter can affect the luminosity of the resultant event, and possibly the success in ultimately yielding a SN Ia. We seek to solidify possible environmental trends in SN Ia rates from direct measures of host galaxy properties, using the sample collected by the Nearby Galaxies Supernova Search project. This study will uncover which has the greatest influence on SN Ia production efficiency: parent population age, rate of star-formation, or metallicity. Here, we will show some preliminary results from SSP model fitting (of age and [Fe/H]) to a selection of hosts obtained thus far from this study. The complete sample will provide a validity test of the mostly indirect trends being established for SNe Ia from the LOSS, SDSS, SNfactory and other surveys, and may ultimately steer future investigations towards more precise SN Ia cosmology.

  4. Tests of Environmental Effects on SN Ia Production

    Science.gov (United States)

    Strolger, Louis-Gregory; van Dyk, Schuyler; Wolff, Schuyler; Campbell, Lachlan; Sadler, Suzanna; Pease, April

    2011-02-01

    The largely unknown type Ia supernova mechanism remains one of the largest sources of possible systematic uncertainty in achieving precise measures of dark energy. The host galaxy environments of SNe Ia provide our best opportunity for constraining the mechanism(s) of the SN Ia progenitor system, i.e., the stars involved, the incubation times, and the sensitivity of SNe Ia to changes in the local gas-phase metallicity. The latter can affect the luminosity of the resultant Ia event, and possibly the success in ultimately yielding a SN Ia event. We seek to solidify possible environmental trends in SN Ia rates from direct measures of host galaxy properties, using the sample collected by the Nearby Galaxies Supernova Search project. This study will uncover which has the greatest influence on SN Ia production efficiency: parent population age, rate of star-formation, or metallicity. Here, we propose to continue our analysis using the Mayall 4m + RCSP to obtain broad SEDs, R_23 metallicities, and star formation rates for 18 of the 25 remaining host galaxies (all z≤0.15) from the NGSS sample (20 targets were obtained in the 2010 semesters). These data will be combined with the remaining sample to be completed in the 2011B semester. The sample will provide a validity test of the mostly indirect trends being established for SNe Ia from the LOSS, SDSS, SNfactory and other surveys, and ultimately steer future investigations towards more precise SN Ia cosmology.

  5. Studies on the rheology and oxygen mass transfer in the clavulanic acid production by Streptomyces clavuligerus

    Directory of Open Access Journals (Sweden)

    E. R. Gouveia

    2000-12-01

    Full Text Available In the present work rheological characteristics and volumetric oxygen transfer coefficient (kLa were investigated during batch cultivations of Streptomyces clavuligerus NRRL 3585 for production of clavulanic acid. The experimental rheological data could be adequately described in terms of the power law model and logistic equation. Significant changes in the rheological parameters consistency index (K and flow behavior index (n were observed with the fermentation evolution. Interesting correlations between the consistency index (K/biomass concentration (C X and the flow behavior index (n/biomass concentration were proposed. Volumetric oxygen mass transfer coefficient (kLa was determined by the gas balance method. Classical correlation relating the volumetric oxygen mass transfer coefficient to the operating conditions, physical and to transport properties, including apparent viscosity (muap, could be applied to the experimental results.

  6. Intermediate mass fragment production in the proton-induced reactions of heavy targets

    CERN Document Server

    Deppman, A; Guimaraes, V; Karapetyan, G S; Balabekyan, A R; Demekhina, N A; Adam, J

    2013-01-01

    The production of intermediate-mass fragments (IMFs) formed in the proton-induced reaction with $^{238}$U and $^{237}$Np at 660 MeV was measured in the LNP Phasotron and in U-400M Cyclotron, Joint Institute for Nuclear Research (JINR), Dubna, Russia. We have applied the induced-activation method in off-line analysis. A total of 115 isotopes of all elements in the range $7 \\leq A \\leq 69$ were unambiguously identified with high precision. There is a consideration that the formed nuclides could be produced in a very asymmetric binary decay of heavy nuclei originating from the spallation of heavy targets. Mass-yield distributions were derived from the data, and were compared with the the simulation code CRISP for multi modal fission.

  7. Resistive thrust production can be as crucial as added mass mechanisms for inertial undulatory swimmers

    CERN Document Server

    Piñeirua, Miguel; Thiria, Benjamin

    2015-01-01

    In this paper, we address a crucial point regarding the description of moderate to high Reynolds numbers aquatic swimmers. For decades, swimming animals have been classified in two different families of propulsive mechanisms based on the Reynolds number: the "resistive" swimmers, using local friction to produce the necessary thrust force for locomotion at low Reynolds number and the "reactive" swimmers, lying in the high Reynolds range, and using added mass acceleration (described by perfect fluid theory). However, inertial swimmers are also systems that dissipate energy, due to their finite size, therefore involving strong resistive contributions, even for high Reynolds numbers. Using a complete model for the hydrodynamic forces, involving both reactive and resistive contributions, we revisit here the physical mechanisms responsible for the thrust production of such swimmers. We show, for instance, that the resistive part of the force balance is as crucial as added mass effects in the modeling of the thrust ...

  8. Estimating initial contaminant mass based on fitting mass-depletion functions to contaminant mass discharge data: Testing method efficacy with SVE operations data

    Science.gov (United States)

    Mainhagu, J.; Brusseau, M. L.

    2016-09-01

    The mass of contaminant present at a site, particularly in the source zones, is one of the key parameters for assessing the risk posed by contaminated sites, and for setting and evaluating remediation goals and objectives. This quantity is rarely known and is challenging to estimate accurately. This work investigated the efficacy of fitting mass-depletion functions to temporal contaminant mass discharge (CMD) data as a means of estimating initial mass. Two common mass-depletion functions, exponential and power functions, were applied to historic soil vapor extraction (SVE) CMD data collected from 11 contaminated sites for which the SVE operations are considered to be at or close to essentially complete mass removal. The functions were applied to the entire available data set for each site, as well as to the early-time data (the initial 1/3 of the data available). Additionally, a complete differential-time analysis was conducted. The latter two analyses were conducted to investigate the impact of limited data on method performance, given that the primary mode of application would be to use the method during the early stages of a remediation effort. The estimated initial masses were compared to the total masses removed for the SVE operations. The mass estimates obtained from application to the full data sets were reasonably similar to the measured masses removed for both functions (13 and 15% mean error). The use of the early-time data resulted in a minimally higher variation for the exponential function (17%) but a much higher error (51%) for the power function. These results suggest that the method can produce reasonable estimates of initial mass useful for planning and assessing remediation efforts.

  9. Blue LED mass production in a close-coupled showerhead MOCVD tool (Conference Presentation)

    Science.gov (United States)

    Boyd, A. R.; Behmenburg, H.; Feron, O.; McAleese, Clifford; O'Dowd, J.; Beckers, Arthur; Heuken, Michael

    2017-02-01

    We report the mass production of blue LEDs on dry-etched patterned sapphire substrates using the AIX R6 tool in a 31×4" configuration. The system was operated in a continuous run mode, i.e. cleaning the showerhead after a series of LED runs. Production stability was characterized by monitoring of wavelength, light output power (LOP), and electrostatic discharge (ESD) yields. We developed a dynamic multi-zone Topside Temperature Control and the TEQualizer function. The TEQualizer function is based on a 400nm pyrometry open loop wafer surface temperature control, using Inside P400 by Laytec. Combining this wafer-to-wafer and run -to-run temperature stability improvement with an optimized wafer carrier, we demonstrated an on-wafer uniformity of stdv of 1.1nm, a wafer-to-wafer uniformity of stdv 1.1nm and a run-to-run reproducibility of stdv 90% in a 6 nm bin. LOP stability was demonstrated within a 3% window with no visible run-to-run trend. An absolute buffer layer growth temperature window was defined through a Design of Experiment on buffer layers targeting best ESD yield - in particular looking into defect related morphology and its correlation with Inside P400 readings. We have demonstrated an ESD yield >90% in continuous run mode to be used in the mass production of InGaN based blue LEDs.

  10. Cost Analysis of Direct Methanol Fuel Cell Stacks for Mass Production

    Directory of Open Access Journals (Sweden)

    Mauro Francesco Sgroi

    2016-11-01

    Full Text Available Fuel cells are very promising technologies for efficient electrical energy generation. The development of enhanced system components and new engineering solutions is fundamental for the large-scale deployment of these devices. Besides automotive and stationary applications, fuel cells can be widely used as auxiliary power units (APUs. The concept of a direct methanol fuel cell (DMFC is based on the direct feed of a methanol solution to the fuel cell anode, thus simplifying safety, delivery, and fuel distribution issues typical of conventional hydrogen-fed polymer electrolyte fuel cells (PEMFCs. In order to evaluate the feasibility of concrete application of DMFC devices, a cost analysis study was carried out in the present work. A 200 W-prototype developed in the framework of a European Project (DURAMET was selected as the model system. The DMFC stack had a modular structure allowing for a detailed evaluation of cost characteristics related to the specific components. A scale-down approach, focusing on the model device and projected to a mass production, was used. The data used in this analysis were obtained both from research laboratories and industry suppliers specialising in the manufacturing/production of specific stack components. This study demonstrates that mass production can give a concrete perspective for the large-scale diffusion of DMFCs as APUs. The results show that the cost derived for the DMFC stack is relatively close to that of competing technologies and that the introduction of innovative approaches can result in further cost savings.

  11. Energy spectra of massive two-body decay products and mass measurement

    CERN Document Server

    Agashe, Kaustubh; Hong, Sungwoo; Kim, Doojin

    2016-01-01

    We have recently established a new method for measuring the mass of unstable particles produced at hadron colliders based on the analysis of the energy distribution of a massless product from their two-body decays. The central ingredient of our proposal is the remarkable result that, for an unpolarized decaying particle, the location of the peak in the energy distribution of the observed decay product is identical to the (fixed) value of the energy that this particle would have in the rest-frame of the decaying particle, which, in turn, is a simple function of the involved masses. In addition, we utilized the property that this energy distribution is symmetric around the location of peak when energy is plotted on a logarithmic scale. The general strategy was demonstrated in several specific cases, including both beyond the SM particles, as well as for the top quark. In the present work, we generalize this method to the case of a massive decay product from a two-body decay; this procedure is far from trivial b...

  12. MASS PRODUCTION OF THE BENEFICIAL NEMATODE STEINERNEMA CARPOCAPSAE UTILIZING A FED-BATCH CULTURING PROCESS

    Directory of Open Access Journals (Sweden)

    Leonard D. Holmes

    2013-04-01

    Full Text Available The present study deals with the batch and fed-batch mass production of Steinernema carpocapsae. S. carpocapsae is an entomoparasitic nematode that is used as a biological control agent of soil-borne crop insect pests. The ability and efficiency of fed-batch culture process was successful through the utilization of the nematode’s bacterial symbiont Xenorhabdus nematophila. Results from the fed-batch process were compared to those obtain from the standard batch process. The fed-batch process successively improved the mass production process of S. carpocapsae employing liquid medium technology. Within the first week of the fed-batch process (day six, the nematode density obtained was 202,000 nematodes mL−1; whereas on day six, batch culture mode resulted in a nematode density of 23,000 nematodes mL−1. The fed-batch process was superior to that of batch production with a yield approximately 8.8-fold higher. In fed-batch process, the nematode yield was improved 88.6 % higher within a short amount of time compared to the batch process. Fed-batch seems to make the process more efficient and possibly economically viable.

  13. 40 CFR 1048.301 - When must I test my production-line engines?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false When must I test my production-line...) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW, LARGE NONROAD SPARK-IGNITION ENGINES Testing Production-line Engines § 1048.301 When must I test my production-line engines? (a) If you produce...

  14. 40 CFR 1054.301 - When must I test my production-line engines?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false When must I test my production-line...) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW, SMALL NONROAD SPARK-IGNITION ENGINES AND EQUIPMENT Production-line Testing § 1054.301 When must I test my production-line engines? (a) If you...

  15. 40 CFR 90.703 - Production line testing by the manufacturer.

    Science.gov (United States)

    2010-07-01

    ... manufacturer. 90.703 Section 90.703 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Manufacturer Production Line Testing Program § 90.703 Production line testing by the manufacturer. (a) Manufacturers of small SI engines shall test production line engines from each engine family according to...

  16. Gravitational quadrupolar coupling to equivalence principle test masses: the general case

    CERN Document Server

    Lockerbie, N A

    2002-01-01

    This paper discusses the significance of the quadrupolar gravitational force in the context of test masses destined for use in equivalence principle (EP) experiments, such as STEP and MICROSCOPE. The relationship between quadrupolar gravity and rotational inertia for an arbitrary body is analysed, and the special, gravitational, role of a body's principal axes of inertia is revealed. From these considerations the gravitational quadrupolar force acting on a cylindrically symmetrical body, due to a point-like attracting source mass, is derived in terms of the body's mass quadrupole tensor. The result is shown to be in agreement with that obtained from MacCullagh's formula (as the starting point). The theory is then extended to cover the case of a completely arbitrary solid body, and a compact formulation for the quadrupolar force on such a body is derived. A numerical example of a dumb-bell's attraction to a local point-like gravitational source is analysed using this theory. Close agreement is found between th...

  17. NGC 1866: A Critical test of Stellar Evolution for Intermediate Mass Stars

    Science.gov (United States)

    Walker, Alistair

    1999-07-01

    We propose to obtain V {F555W} and I {F814W} images centered on the LMC cluster NGC 1866, with a range of exposure times such that we can measure all cluster stars from the brightest at V 15 down to V 25. NGC 1866 has age 100 Myr and is so populous that the evolving stars, with M 5 M_sun, are caught even in short phases of evolution. As such, it provides a critical test of stellar evolution theory applicable to these intermediate mass stars. We will prepare a color- magnitude diagram that will, for the first time, include all the luminous evolved stars. This is impossible to achieve from ground-based observations due to crowding. We will also measure a luminosity function for the unevolved main sequence to M 0.5 M_sun which allows both determination of the IMF for cluster stars with masses in the range 0.5 - 5 M_sun and an investigation of the cluster dynamical evolution by study of the spatial mass distribution. The deep and accurate MS photometry will also permit precise fitting of a fiducial ZAMS, and hence derivation of a distance relative to the Hyades, the basis of the ZAMS calibration. Since NGC 1866 contains at least 23 Cepheid variables, we will thus calibrate the Period-Luminosity relation zeropoint, and determine the distance to the LMC relative to the very accurate Hipparcos parallax distance to the Hyades with a minimum of steps and assumptions.

  18. Pep2Path: automated mass spectrometry-guided genome mining of peptidic natural products.

    Directory of Open Access Journals (Sweden)

    Marnix H Medema

    2014-09-01

    Full Text Available Nonribosomally and ribosomally synthesized bioactive peptides constitute a source of molecules of great biomedical importance, including antibiotics such as penicillin, immunosuppressants such as cyclosporine, and cytostatics such as bleomycin. Recently, an innovative mass-spectrometry-based strategy, peptidogenomics, has been pioneered to effectively mine microbial strains for novel peptidic metabolites. Even though mass-spectrometric peptide detection can be performed quite fast, true high-throughput natural product discovery approaches have still been limited by the inability to rapidly match the identified tandem mass spectra to the gene clusters responsible for the biosynthesis of the corresponding compounds. With Pep2Path, we introduce a software package to fully automate the peptidogenomics approach through the rapid Bayesian probabilistic matching of mass spectra to their corresponding biosynthetic gene clusters. Detailed benchmarking of the method shows that the approach is powerful enough to correctly identify gene clusters even in data sets that consist of hundreds of genomes, which also makes it possible to match compounds from unsequenced organisms to closely related biosynthetic gene clusters in other genomes. Applying Pep2Path to a data set of compounds without known biosynthesis routes, we were able to identify candidate gene clusters for the biosynthesis of five important compounds. Notably, one of these clusters was detected in a genome from a different subphylum of Proteobacteria than that in which the molecule had first been identified. All in all, our approach paves the way towards high-throughput discovery of novel peptidic natural products. Pep2Path is freely available from http://pep2path.sourceforge.net/, implemented in Python, licensed under the GNU General Public License v3 and supported on MS Windows, Linux and Mac OS X.

  19. Hard-Photon Production and Tests of QED at LEP

    CERN Document Server

    Acciarri, M; Adriani, O; Aguilar-Benítez, M; Alcaraz, J; Alemanni, G; Allaby, James V; Aloisio, A; Alviggi, M G; Ambrosi, G; Anderhub, H; Andreev, V P; Angelescu, T; Anselmo, F; Arefev, A; Azemoon, T; Aziz, T; Bagnaia, P; Baksay, L; Balandras, A; Ball, R C; Banerjee, S; Banerjee, Sw; Barczyk, A; Barillère, R; Barone, L; Bartalini, P; Basile, M; Battiston, R; Bay, A; Becattini, F; Becker, U; Behner, F; Bellucci, L; Berdugo, J; Berges, P; Bertucci, B; Betev, B L; Bhattacharya, S; Biasini, M; Biland, A; Blaising, J J; Blyth, S C; Bobbink, Gerjan J; Böhm, A; Boldizsar, L; Borgia, B; Bourilkov, D; Bourquin, Maurice; Braccini, S; Branson, J G; Brigljevic, V; Brochu, F; Buffini, A; Buijs, A; Burger, J D; Burger, W J; Button, A M; Cai, X D; Campanelli, M; Capell, M; Cara Romeo, G; Carlino, G; Cartacci, A M; Casaus, J; Castellini, G; Cavallari, F; Cavallo, N; Cecchi, C; Cerrada-Canales, M; Cesaroni, F; Chamizo-Llatas, M; Chang, Y H; Chaturvedi, U K; Chemarin, M; Chen, A; Chen, G; Chen, G M; Chen, H F; Chen, H S; Chiefari, G; Cifarelli, Luisa; Cindolo, F; Civinini, C; Clare, I; Clare, R; Coignet, G; Colijn, A P; Colino, N; Costantini, S; Cotorobai, F; Cozzoni, B; de la Cruz, B; Csilling, Akos; Cucciarelli, S; Dai, T S; van Dalen, J A; D'Alessandro, R; De Asmundis, R; Déglon, P L; Degré, A; Deiters, K; Della Volpe, D; Denes, P; De Notaristefani, F; De Salvo, A; Diemoz, M; Van Dierendonck, D N; Di Lodovico, F; Dionisi, C; Dittmar, Michael; Dominguez, A; Doria, A; Dova, M T; Duchesneau, D; Dufournaud, D; Duinker, P; Durán, I; El-Mamouni, H; Engler, A; Eppling, F J; Erné, F C; Extermann, Pierre; Fabre, M; Faccini, R; Falagán, M A; Falciano, S; Favara, A; Fay, J; Fedin, O; Felcini, Marta; Ferguson, T; Ferroni, F; Fesefeldt, H S; Fiandrini, E; Field, J H; Filthaut, Frank; Fisher, P H; Fisk, I; Forconi, G; Fredj, L; Freudenreich, Klaus; Furetta, C; Galaktionov, Yu; Ganguli, S N; García-Abia, P; Gataullin, M; Gau, S S; Gentile, S; Gheordanescu, N; Giagu, S; Gong, Z F; Grenier, G; Grimm, O; Grünewald, M W; Guida, M; van Gulik, R; Gupta, V K; Gurtu, A; Gutay, L J; Haas, D; Hasan, A; Hatzifotiadou, D; Hebbeker, T; Hervé, A; Hidas, P; Hirschfelder, J; Hofer, H; Holzner, G; Hoorani, H; Hou, S R; Iashvili, I; Jin, B N; Jones, L W; de Jong, P; Josa-Mutuberria, I; Khan, R A; Kaur, M; Kienzle-Focacci, M N; Kim, D; Kim, D H; Kim, J K; Kim, S C; Kirkby, Jasper; Kiss, D; Kittel, E W; Klimentov, A; König, A C; Kopp, A; Koutsenko, V F; Kräber, M H; Krämer, R W; Krenz, W; Krüger, A; Kunin, A; Ladrón de Guevara, P; Laktineh, I; Landi, G; Lassila-Perini, K M; Lebeau, M; Lebedev, A; Lebrun, P; Lecomte, P; Lecoq, P; Le Coultre, P; Lee, H J; Le Goff, J M; Leiste, R; Leonardi, E; Levchenko, P M; Li Chuan; Likhoded, S A; Lin, C H; Lin, W T; Linde, Frank L; Lista, L; Liu, Z A; Lohmann, W; Longo, E; Lü, Y S; Lübelsmeyer, K; Luci, C; Luckey, D; Lugnier, L; Luminari, L; Lustermann, W; Ma Wen Gan; Maity, M; Malgeri, L; Malinin, A; Maña, C; Mangeol, D J J; Marchesini, P A; Marian, G; Martin, J P; Marzano, F; Massaro, G G G; Mazumdar, K; McNeil, R R; Mele, S; Merola, L; Meschini, M; Metzger, W J; Von der Mey, M; Mihul, A; Milcent, H; Mirabelli, G; Mnich, J; Mohanty, G B; Molnár, P; Monteleoni, B; Moulik, T; Muanza, G S; Muheim, F; Muijs, A J M; Musy, M; Napolitano, M; Nessi-Tedaldi, F; Newman, H; Niessen, T; Nisati, A; Nowak, H; Oh, Yu D; Organtini, G; Oulianov, A; Palomares, C; Pandoulas, D; Paoletti, S; Paolucci, P; Paramatti, R; Park, H K; Park, I H; Pascale, G; Passaleva, G; Patricelli, S; Paul, T; Pauluzzi, M; Paus, C; Pauss, Felicitas; Pedace, M; Pensotti, S; Perret-Gallix, D; Petersen, B; Piccolo, D; Pierella, F; Pieri, M; Piroué, P A; Pistolesi, E; Plyaskin, V; Pohl, M; Pozhidaev, V; Postema, H; Pothier, J; Produit, N; Prokofev, D; Prokofiev, D O; Quartieri, J; Rahal-Callot, G; Rahaman, M A; Raics, P; Raja, N; Ramelli, R; Rancoita, P G; Raspereza, A V; Raven, G; Razis, P A; Ren, D; Rescigno, M; Reucroft, S; Van Rhee, T; Riemann, S; Riles, K; Robohm, A; Rodin, J; Roe, B P; Romero, L; Rosca, A; Rosier-Lees, S; Rubio, Juan Antonio; Ruschmeier, D; Rykaczewski, H; Saremi, S; Sarkar, S; Salicio, J; Sánchez, E; Sanders, M P; Sarakinos, M E; Schäfer, C; Shchegelskii, V; Schmidt-Kärst, S; Schmitz, D; Schopper, Herwig Franz; Schotanus, D J; Schwering, G; Sciacca, C; Sciarrino, D; Seganti, A; Servoli, L; Shevchenko, S; Shivarov, N; Shoutko, V; Shumilov, E; Shvorob, A V; Siedenburg, T; Son, D; Smith, B; Spillantini, P; Steuer, M; Stickland, D P; Stone, A; Stone, H; Stoyanov, B; Strässner, A; Sudhakar, K; Sultanov, G G; Sun, L Z; Suter, H; Swain, J D; Szillási, Z; Sztaricskai, T; Tang, X W; Tauscher, Ludwig; Taylor, L; Timmermans, C; Ting, Samuel C C; Ting, S M; Tonwar, S C; Tóth, J; Tully, C; Tung, K L; Uchida, Y; Ulbricht, J; Valente, E; Vesztergombi, G; Vetlitskii, I; Vicinanza, D; Viertel, Gert M; Villa, S; Vivargent, M; Vlachos, S; Vodopyanov, I; Vogel, H; Vogt, H; Vorobev, I; Vorobyov, A A; Vorvolakos, A; Wadhwa, M; Wallraff, W; Wang, M; Wang, X L; Wang, Z M; Weber, A; Weber, M; Wienemann, P; Wilkens, H; Wu, S X; Wynhoff, S; Xia, L; Xu, Z Z; Yang, B Z; Yang, C G; Yang, H J; Yang, M; Ye, J B; Yeh, S C; Zalite, A; Zalite, Yu; Zhang, Z P; Zhu, G Y; Zhu, R Y; Zichichi, A; Zilizi, G; Zöller, M

    2000-01-01

    The total and differential cross sections of the process $\\epem \\ra n \\gamma$ with $n \\geq 2$ are measuredusing data collected by the L3 experiment at centre--of--mass energies of $\\sqrt{s}=183$ and $189$\\GeV{}. The results are in agreement with the Standard Model expectations. Limits are set on deviationsfrom QED, contact interaction cut-off parameters and masses of excited electrons.

  20. Quantitation of acrylamide in food products by liquid chromatography/mass spectrometry.

    Science.gov (United States)

    Eberhart, B Loye; Ewald, Deborah K; Sanders, Robert A; Tallmadge, Daniel H; Zyzak, David V; Strothers, Melissa A

    2005-01-01

    A simple and inexpensive liquid chromatography/mass spectrometry (LC/MS) method was developed for the quantitation of acrylamide in various food products. The method involved spiking the isotope-substituted internal standard (1-C13 acrylamide) onto 6.00 g of the food product, adding 40 mL distilled/deionized water, and heating at 65 degrees C for 30 min. Afterwards, 10 mL ethylene dichloride was added and the mixture was homogenized for 30 s and centrifuged at 2700 x g for 30 min, and then 8 g supernatant was extracted with 10, 5, and 5 mL portions of ethyl acetate. The extracts were combined, dried with sodium sulfate, and concentrated to 100-200 microL. Acrylamide was determined by analysis of the final extract on a single quadrupole, bench-top mass spectrometer with electrospray ionization, using a 2 mm id C18 column and monitoring m/z = 72 (acrylamide) and m/z = 73 (internal standard). For difficult food matrixes, such as coffee and cocoa, a solid-phase extraction cleanup step was incorporated to improve both chromatography and column lifetime. The method had a limit of quantitation of 10 ppb, and coefficients of determination (r2) for calibration curves were typically better than 0.998. Acceptable spike recovery results were achieved in 11 different food matrixes. Precision in potato chip analyses was 5-8% (relative standard deviation). This method provides an LC/MS alternative to the current LC/MS/MS methods and derivatization gas chromatography/mass spectrometry methods, and is applicable to difficult food products such as coffee, cocoa, and high-salt foods.

  1. Standard test methods for chemical and mass spectrometric analysis of nuclear-grade gadolinium oxide (Gd2O3) powder

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2006-01-01

    1.1 These test methods cover procedures for the chemical and mass spectrometric analysis of nuclear-grade gadolinium oxide powders to determine compliance with specifications. 1.2 The analytical procedures appear in the following order: Sections Carbon by Direct CombustionThermal Conductivity C1408 Test Method for Carbon (Total) in Uranium Oxide Powders and Pellets By Direct Combustion-Infrared Detection Method Total Chlorine and Fluorine by Pyrohydrolysis Ion Selective Electrode C1502 Test Method for Determination of Total Chlorine and Fluorine in Uranium Dioxide and Gadolinium Oxide Loss of Weight on Ignition 7-13 Sulfur by CombustionIodometric Titration Impurity Elements by a Spark-Source Mass Spectrographic C761 Test Methods for Chemical, Mass Spectrometric, Spectrochemical,Nuclear, and Radiochemical Analysis of Uranium Hexafluoride C1287 Test Method for Determination of Impurities In Uranium Dioxide By Inductively Coupled Plasma Mass Spectrometry Gadolinium Content in Gadolinium Oxid...

  2. Networking mass spectrometer data systems for improved productivity and electronic archiving of data.

    Science.gov (United States)

    Hayward, M J; Robandt, P V; Meek, J T; Thomson, M L

    1993-09-01

    Several Finngan-MAT mass spectrometer data systems were networked together to achieve the following two primary objectives: (1) to allow access to mass spectrometry data and data processing functions from remote locations without affecting simultaneous data acquisition at the instruments, and (2) to electronically archive mass spectrometry data at a central location on a high-capacity, fast-access device that allows rapid retrieval of archived data for all data processing operations at all locations. UNIX workstations, IBM PC/AT-compatible computers, and Data General Nova minicomputers were connected via Ethernet interfaces to allow rapid data transfer among all systems as well as X-Windows access to UNIX-based systems. Bridging techniques were used to isolate possible high-traffic areas of the network and to enable security measures for adequate protection of files. Additionally, serial connections were made through a Northern Telecom phone system to provide remote terminal access to the Data General Nova-based systems. Use of these connectivity techniques significantly improved productivity by allowing retrieval, processing, and printing of data from remote locations, such as office areas, without affecting data acquisition, processing, and printing performed simultaneously at the instruments. For archival purposes, data files are electronically stored on high-capacity magneto-optical disks for rapid retrieval. A highcapacity fixed disk is also available for centralized temporary data file storage. A Digital Equipment Corporation DECstation 2100 UNIX workstation was used as the file server for centralized data storage while being simultaneously utilized as the data system computer for one of the mass spectrometers. Utilization of this UNIX-based file server system in conjunction with Ethernet connectivity techniques provides a centralized, rapid-access, high-capacity, cost- and space-efficient method for electronic archival of mass spectrometry raw data recorded

  3. Classification of photobacteria associated with spoilage of fish products by numerical taxanomy and pyrolysis mass spectrometry

    DEFF Research Database (Denmark)

    Dalgaard, Paw; Manfio, G.P.; Goodfellow, M.

    1997-01-01

    , from spoiled products and by using a specific detection method. The data were analysed using the similarity coefficient and the unweighted pair-group with arithmetic averages algorithm. In addition twenty-six of the fish isolates and five reference strains were analysed by Curie-point pyrolysis mass...... sub-groups. One sub-group of psychrotolerant P. phosphoreum strains, which was selected in modified atmosphere packed fish stored at low temperature, was also highlighted using each of the methods. The importance of classifying food spoilage bacteria has been shown and a simple key generated...

  4. Full top quark mass dependence in Higgs boson pair production at NLO

    CERN Document Server

    Borowka, S; Heinrich, G; Jones, S P; Kerner, M; Schlenk, J; Zirke, T

    2016-01-01

    We study the effects of the exact top-quark mass dependent two-loop corrections to Higgs boson pair production by gluon fusion at the LHC and at a 100 TeV hadron collider. We perform a detailed comparison of the full next-to-leading order result to various approximations at the level of differential distributions and also analyse non-standard Higgs self-coupling scenarios. We find that the different next-to-leading order approximations differ from the full result by up to 50 percent in relevant differential distributions. This clearly stresses the importance of the full NLO result.

  5. Large mass Q-Qbar production from the Color Glass Condensate

    CERN Document Server

    Gelis, François

    2004-01-01

    We compute quark-antiquark pair production in the context of the Color Glass Condensate model for central heavy-ion collisions. The calculation is performed analytically to leading order in the density of hard sources present in the projectiles, and is applicable to quarks with a mass large compared to the saturation momentum. The formulas derived in this paper are compared to expressions derived in the framework of collinearly factorized perturbative QCD and in kt factorization models. We comment on the breaking of kt factorization which occurs beyond leading order in our approach.

  6. Study of electron pair production below the Z mass at the CERN overlinepp collider

    Science.gov (United States)

    Alitti, J.; Ambrosini, G.; Ansari, R.; Autiero, D.; Bareyre, P.; Bertram, I. A.; Blaylock, G.; Bonamy, P.; Borer, K.; Bourliaud, M.; Buskulic, D.; Carboni, G.; Cavalli, D.; Cavasinni, V.; Cenci, P.; Chollet, J. C.; Conta, C.; Costa, G.; Costantini, F.; Cozzi, L.; Cravero, A.; Curatolo, M.; Dell'Acqua, A.; DelPrete, T.; DeWolf, R. S.; DiLella, L.; Ducros, Y.; Egan, G. F.; Einsweiler, K. F.; Esposito, B.; Fayard, L.; Federspiel, A.; Ferrari, R.; Fraternali, M.; Friodevaux, D.; Fumagalli, G.; Gaillard, J. M.; Gianotti, F.; Gildemeister, O.; Gössling, C.; Goggi, V. G.; Grünendahl, S.; Hara, K.; Hellman, S.; Hrivnac, J.; Hufnagel, H.; Hugentobler, E.; Hultqvist, K.; Iacopini, E.; Incandela, J.; Jakobs, K.; Jenni, P.; Kluge, E. E.; Kurz, N.; Lami, S.; Lariccia, P.; Lefebvre, M.; Linssen, L.; Livan, M.; Lubrano, P.; Magneville, C.; Mandelli, L.; Mapelli, L.; Mazzanti, M.; Meier, K.; Merkel, B.; Meyer, J. P.; Moniez, M.; Moning, R.; Morganti, M.; Müller, L.; Munday, D. J.; Nessi, M.; Nessi-Tedaldi, F.; Onions, C.; Pal, T.; Parker, M. A.; Parrour, G.; Pastore, F.; Pennacchio, E.; Pentney, J. M.; Pepe, M.; Perini, L.; Petridou, C.; Petroff, P.; Plothow-Besch, H.; Polesello, G.; Poppleton, A.; Pretzl, K.; Primavera, M.; Punturo, M.; Repellin, J. P.; Rimoldi, A.; Sacchi, M.; Scampoli, P.; Schacher, J.; Schmidt, B.; Simak, V.; Singh, S. L.; Sondermann, V.; Spiwoks, R.; Stapnes, S.; Talamonti, C.; Tondini, F.; Tovey, S. N.; Tsesmelis, E.; Unal, G.; Valdata-Nappi, M.; Vercesi, V.; Weidberg, A. R.; Wells, P. S.; White, T. O.; Wood, D. R.; Wotton, S. A.; Zaccone, H.; Zylberstejn, A.; UA2 Collaboration; Bern-Cambridge-CERN-Dortmund-Heidelberg-Melbourne-Milano-Orsay (LAL)-Pavia-Perugia-Pisa-Saclay (CEN)

    1992-01-01

    Results on the cross section for the production of electron pairs in overlinepp collisions at √ s = 630 GeV are presented. The measured value is σ = 405 ± 51 (syst.) ± 84 (syst.) pb, in the invariant mass interval 10 < m< 70 GeV. The results are compared to recent theoretical calculations which include O( αs2) QCD contributions. The comparison of these data with those of lower energy experiments show approximate scaling as a function of the variable √τ = {m}/{√s}.

  7. Inter-comparison of ice sheet mass balance products from GRACE: ESA CCI Round Robin results

    DEFF Research Database (Denmark)

    Groth, A.; Horwath, M.; Horvath, A.

    spatial resolution and complex error structures place particular demands on the applied processing strategy. To choose the most suitable algorithm which minimizes the impact of GRACE errors and signal leakage errors on GMB products, an open Round Robin experiment was set up. Participants were asked...... of the Earth (e.g. cryoshpere, ocean, continental hydrology). By comparing the derived synthetic mass changes with the a priori known 'synthetic truth', leakage errors can be quantified.Here we inter-compare the Round Robin results from six individual contributions, relying on different processing strategies...

  8. Test Mass Temperature Field and Laser Aberration Modeling in Advanced LIGO

    Science.gov (United States)

    Ramette, Joshua; Kasprzack, Marie; Gonzalez, Gabriela; Brooks, Aidan; Blair, Carl; Kandhasamy, Shivaraj; Wang, Haoyu; LIGO Collaboration

    2017-01-01

    Advanced LIGO uses high laser power in the main interferometer arm cavities to achieve design sensitivity. A small part of this power is absorbed in the interferometer cavity mirrors where it creates thermal lenses. Actuation by ``ring heaters,'' additional heater elements aimed to reduce the temperature gradients in the mirrors, minimizes aberrations in the main laser beam due to thermal lensing. We derive the first analytical model of the temperature field contribution in the mirrors generated by an ideal ring heater. In addition, we simulate the test mass temperature field using finite element analysis software and find agreement with the prediction of our ring heater analytical model and existing models for self-heating of the test mass by the main laser beam. From our ring heater temperature field models, we then express the resulting optical aberration contribution in the main laser and compare to Hartmann wavefront sensor measurements of the aberration. Used in conjunction with wavefront measurements, our model provides a more complete understanding of the thermal state of the cavity mirrors and will allow a more efficient use of the ring heaters in Advanced LIGO. We thank the National Science Foundation for supporting this work (NSF grant #1262890 and #1205882).

  9. Testing cold dark matter with the low mass Tully-Fisher relation

    CERN Document Server

    Blanton, Michael R; West, Andrew A

    2007-01-01

    The galaxy circular velocity function at small masses is related to the matter power spectrum on small scales. Although this function is well-studied for Local Group dwarfs, theoretical predictions and observational measurements are difficult for satellite galaxies, because of ram pressure and tidal stripping. By contrast, isolated dwarf galaxies are less affected by these processes, and almost always have enough 21cm emission to trace their dynamics robustly. Here, we test cold dark matter cosmology using isolated low mass dwarf galaxies from the SDSS with measured 21cm widths. We find consistency between the predicted and observed number density of isolated galaxies down to circular velocities of 50 km/s. Our technique yields a direct test of small-scale cosmology independent of the Lyman-alpha forest power spectrum, but our sample is currently statistically less powerful: warm dark matter particles heavier than 0.5 keV cannot be ruled out. Our major systematic uncertainty is the surface brightness limit of...

  10. Interpolation of the magnetic field at the test masses in eLISA

    Science.gov (United States)

    Mateos, I.; Díaz-Aguiló, M.; Ramos-Castro, J.; García-Berro, E.; Lobo, A.

    2015-08-01

    A feasible design for a magnetic diagnostics subsystem for eLISA will be based on that of its precursor mission, LISA Pathfinder. Previous experience indicates that magnetic field estimation at the positions of the test masses has certain complications. This is due to two reasons. The first is that magnetometers usually back-act due to their measurement principles (i.e., they also create their own magnetic fields), while the second is that the sensors selected for LISA Pathfinder have a large size, which conflicts with space resolution and with the possibility of having a sufficient number of them to properly map the magnetic field around the test masses. However, high-sensitivity and small-sized sensors that significantly mitigate the two aforementioned limitations exist, and have been proposed to overcome these problems. Thus, these sensors will be likely selected for the magnetic diagnostics subsystem of eLISA. Here we perform a quantitative analysis of the new magnetic subsystem, as it is currently conceived, and assess the feasibility of selecting these sensors in the final configuration of the magnetic diagnostic subsystem.

  11. Charge-Induced Force Noise on Free-Falling Test Masses: Results from LISA Pathfinder

    Science.gov (United States)

    Armano, M.; Audley, H.; Auger, G.; Baird, J. T.; Binetruy, P.; Born, M.; Bortoluzzi, D.; Brandt, N.; Bursi, A.; Caleno, M.; Cavalleri, A.; Cesarini, A.; Cruise, M.; Danzmann, K.; de Deus Silva, M.; Diepholz, I.; Dolesi, R.; Dunbar, N.; Ferraioli, L.; Ferroni, V.; Fitzsimons, E. D.; Flatscher, R.; Freschi, M.; Gallegos, J.; García Marirrodriga, C.; Gerndt, R.; Gesa, L.; Gibert, F.; Giardini, D.; Giusteri, R.; Grimani, C.; Grzymisch, J.; Harrison, I.; Heinzel, G.; Hewitson, M.; Hollington, D.; Hueller, M.; Huesler, J.; Inchauspé, H.; Jennrich, O.; Jetzer, P.; Johlander, B.; Karnesis, N.; Kaune, B.; Killow, C. J.; Korsakova, N.; Lloro, I.; Liu, L.; López-Zaragoza, J. P.; Maarschalkerweerd, R.; Madden, S.; Mance, D.; Martín, V.; Martin-Polo, L.; Martino, J.; Martin-Porqueras, F.; Mateos, I.; McNamara, P. W.; Mendes, J.; Mendes, L.; Moroni, A.; Nofrarias, M.; Paczkowski, S.; Perreur-Lloyd, M.; Petiteau, A.; Pivato, P.; Plagnol, E.; Prat, P.; Ragnit, U.; Ramos-Castro, J.; Reiche, J.; Romera Perez, J. A.; Robertson, D. I.; Rozemeijer, H.; Rivas, F.; Russano, G.; Sarra, P.; Schleicher, A.; Slutsky, J.; Sopuerta, C.; Sumner, T. J.; Texier, D.; Thorpe, J. I.; Trenkel, C.; Vetrugno, D.; Vitale, S.; Wanner, G.; Ward, H.; Wass, P. J.; Wealthy, D.; Weber, W. J.; Wittchen, A.; Zanoni, C.; Ziegler, T.; Zweifel, P.; LISA Pathfinder Collaboration

    2017-04-01

    We report on electrostatic measurements made on board the European Space Agency mission LISA Pathfinder. Detailed measurements of the charge-induced electrostatic forces exerted on free-falling test masses (TMs) inside the capacitive gravitational reference sensor are the first made in a relevant environment for a space-based gravitational wave detector. Employing a combination of charge control and electric-field compensation, we show that the level of charge-induced acceleration noise on a single TM can be maintained at a level close to 1.0 fm s-2 Hz-1 /2 across the 0.1-100 mHz frequency band that is crucial to an observatory such as the Laser Interferometer Space Antenna (LISA). Using dedicated measurements that detect these effects in the differential acceleration between the two test masses, we resolve the stochastic nature of the TM charge buildup due to interplanetary cosmic rays and the TM charge-to-force coupling through stray electric fields in the sensor. All our measurements are in good agreement with predictions based on a relatively simple electrostatic model of the LISA Pathfinder instrument.

  12. Model test of anchoring effect on zonal disintegration in deep surrounding rock masses.

    Science.gov (United States)

    Chen, Xu-Guang; Zhang, Qiang-Yong; Wang, Yuan; Liu, De-Jun; Zhang, Ning

    2013-01-01

    The deep rock masses show a different mechanical behavior compared with the shallow rock masses. They are classified into alternating fractured and intact zones during the excavation, which is known as zonal disintegration. Such phenomenon is a great disaster and will induce the different excavation and anchoring methodology. In this study, a 3D geomechanics model test was conducted to research the anchoring effect of zonal disintegration. The model was constructed with anchoring in a half and nonanchoring in the other half, to compare with each other. The optical extensometer and optical sensor were adopted to measure the displacement and strain changing law in the model test. The displacement laws of the deep surrounding rocks were obtained and found to be nonmonotonic versus the distance to the periphery. Zonal disintegration occurs in the area without anchoring and did not occur in the model under anchoring condition. By contrasting the phenomenon, the anchor effect of restraining zonal disintegration was revealed. And the formation condition of zonal disintegration was decided. In the procedure of tunnel excavation, the anchor strain was found to be alternation in tension and compression. It indicates that anchor will show the nonmonotonic law during suppressing the zonal disintegration.

  13. Model Test of Anchoring Effect on Zonal Disintegration in Deep Surrounding Rock Masses

    Directory of Open Access Journals (Sweden)

    Xu-Guang Chen

    2013-01-01

    Full Text Available The deep rock masses show a different mechanical behavior compared with the shallow rock masses. They are classified into alternating fractured and intact zones during the excavation, which is known as zonal disintegration. Such phenomenon is a great disaster and will induce the different excavation and anchoring methodology. In this study, a 3D geomechanics model test was conducted to research the anchoring effect of zonal disintegration. The model was constructed with anchoring in a half and nonanchoring in the other half, to compare with each other. The optical extensometer and optical sensor were adopted to measure the displacement and strain changing law in the model test. The displacement laws of the deep surrounding rocks were obtained and found to be nonmonotonic versus the distance to the periphery. Zonal disintegration occurs in the area without anchoring and did not occur in the model under anchoring condition. By contrasting the phenomenon, the anchor effect of restraining zonal disintegration was revealed. And the formation condition of zonal disintegration was decided. In the procedure of tunnel excavation, the anchor strain was found to be alternation in tension and compression. It indicates that anchor will show the nonmonotonic law during suppressing the zonal disintegration.

  14. LISA Pathfinder test-mass charging during galactic cosmic-ray flux short-term variations

    Science.gov (United States)

    Grimani, C.; Fabi, M.; Lobo, A.; Mateos, I.; Telloni, D.

    2015-02-01

    Metal free-floating test masses aboard the future interferometers devoted to gravitational wave detection in space are charged by galactic and solar cosmic rays with energies \\gt 100 MeV/n. This process represents one of the main sources of noise in the lowest frequency band (\\lt 10-3 Hz) of these experiments. We study here the charging of the LISA Pathfinder (LISA-PF) gold-platinum test masses due to galactic cosmic-ray (GCR) protons and helium nuclei with the Fluka Monte Carlo toolkit. Projections of the energy spectra of GCRs during the LISA-PF operations in 2015 are considered. This work was carried out on the basis of the solar activity level and solar polarity epoch expected for LISA-PF. The effects of GCR short-term variations are evaluated here for the first time. Classical Forbush decreases, GCR variations induced by the Sun rotation, and fluctuations in the LISA-PF frequency bandwidth are discussed.

  15. Interpolation of the magnetic field at the test masses in eLISA

    CERN Document Server

    Mateos, I; Ramos-Castro, J; García-Berro, E; Lobo, A

    2016-01-01

    A feasible design for a magnetic diagnostics subsystem for eLISA will be based on that of its precursor mission, LISA Pathfinder. Previous experience indicates that magnetic field estimation at the positions of the test masses has certain complications. This is due to two reasons. The first one is that magnetometers usually back-act due to their measurement principles (i.e., they also create their own magnetic fields), while the second is that the sensors selected for LISA Pathfinder have a large size, which conflicts with space resolution and with the possibility of having a sufficient number of them to properly map the magnetic field around the test masses. However, high-sensitivity and small-size sensors that significantly mitigate the two aforementioned limitations exist, and have been proposed to overcome these problems. Thus, these sensors will be likely selected for the magnetic diagnostics subsystem of eLISA. Here we perform a quantitative analysis of the new magnetic subsystem, as it is currently con...

  16. Hairy root culture for mass-production of high-value secondary metabolites.

    Science.gov (United States)

    Srivastava, Smita; Srivastava, Ashok K

    2007-01-01

    Plant cell cultivations are being considered as an alternative to agricultural processes for producing valuable phytochemicals. Since many of these products (secondary metabolites) are obtained by direct extraction from plants grown in natural habitat, several factors can alter their yield. The use of plant cell cultures has overcome several inconveniences for the production of these secondary metabolites. Organized cultures, and especially root cultures, can make a significant contribution in the production of secondary metabolites. Most of the research efforts that use differentiated cultures instead of cell suspension cultures have focused on transformed (hairy) roots. Agrobacterium rhizogenes causes hairy root disease in plants. The neoplastic (cancerous) roots produced by A. rhizogenes infection are characterized by high growth rate, genetic stability and growth in hormone free media. These genetically transformed root cultures can produce levels of secondary metabolites comparable to that of intact plants. Hairy root cultures offer promise for high production and productivity of valuable secondary metabolites (used as pharmaceuticals, pigments and flavors) in many plants. The main constraint for commercial exploitation of hairy root cultivations is the development and scaling up of appropriate reactor vessels (bioreactors) that permit the growth of interconnected tissues normally unevenly distributed throughout the vessel. Emphasis has focused on designing appropriate bioreactors suitable to culture the delicate and sensitive plant hairy roots. Recent reactors used for mass production of hairy roots can roughly be divided as liquid-phase, gas-phase, or hybrid reactors. The present review highlights the nature, applications, perspectives and scale up of hairy root cultures for the production of valuable secondary metabolites.

  17. Design and mass production of the optical modules for KM3NeT-Italia project

    Directory of Open Access Journals (Sweden)

    Leonora Emanuele

    2016-01-01

    Full Text Available The KM3NeT European project aims at constructing a km3 underwater neutrino telescope in the depths of the Mediterranean Sea. The first phase that is under construction will comprise eight tower-like detection structures (KM3NeT-Italia, which will form the internal core of a km3-scale detector. The detection element of KM3NeT-Italia, the optical module, is made of a 13-inch pressure-resistant glass-vessel that contains a single 10-inch photomultiplier and the relative electronics. The design of the whole optical module, the main results obtained from the massive photomultipliers measurements, and the foremost phases of the mass production procedure performed at the production site of Catania are also presented.

  18. Design and mass production of the optical modules for KM3NeT-Italia project

    Science.gov (United States)

    Leonora, Emanuele; Aiello, Sebastiano; Giordano, Valentina

    2016-04-01

    The KM3NeT European project aims at constructing a km3 underwater neutrino telescope in the depths of the Mediterranean Sea. The first phase that is under construction will comprise eight tower-like detection structures (KM3NeT-Italia), which will form the internal core of a km3-scale detector. The detection element of KM3NeT-Italia, the optical module, is made of a 13-inch pressure-resistant glass-vessel that contains a single 10-inch photomultiplier and the relative electronics. The design of the whole optical module, the main results obtained from the massive photomultipliers measurements, and the foremost phases of the mass production procedure performed at the production site of Catania are also presented.

  19. Nuclear parton density modifications from low-mass lepton pair production at the LHC

    CERN Document Server

    Brandt, M; König, F

    2014-01-01

    In this article, we investigate the potential of low-mass lepton pair production in proton-ion collisions at the LHC to constrain nuclear modifications of parton densities. Similarly to prompt photon production, the transverse momentum spectrum is shown to be dominated by the QCD Compton process, but has virtually no fragmentation or isolation uncertainties. Depending on the orientation of the proton and ion beams and on the use of central or forward detector components, all interesting regions of nuclear effects (shadowing, antishadowing, isospin and EMC effects) can be probed. Ratios of cross sections allow to eliminate theoretical scale and bare-proton parton density errors as well as many experimental systematic uncertainties.

  20. Nuclear parton density modifications from low-mass lepton pair production at the LHC

    Science.gov (United States)

    Brandt, M.; Klasen, M.; König, F.

    2014-07-01

    In this article, we investigate the potential of low-mass lepton pair production in proton-ion collisions at the LHC to constrain nuclear modifications of parton densities. Similarly to prompt photon production, the transverse momentum spectrum is shown to be dominated by the QCD Compton process, but has virtually no fragmentation or isolation uncertainties. Depending on the orientation of the proton and ion beams and on the use of central or forward detector components, all interesting regions of nuclear effects (shadowing, antishadowing, isospin and EMC effects) can be probed. Ratios of cross sections allow to eliminate theoretical scale and bare-proton parton density errors as well as many experimental systematic uncertainties.

  1. Nuclear parton density modifications from low-mass lepton pair production at the LHC

    Energy Technology Data Exchange (ETDEWEB)

    Brandt, M., E-mail: matthiasbrandt@uni-muenster.de; Klasen, M., E-mail: michael.klasen@uni-muenster.de; König, F., E-mail: f.koenig@uni-muenster.de

    2014-07-15

    In this article, we investigate the potential of low-mass lepton pair production in proton–ion collisions at the LHC to constrain nuclear modifications of parton densities. Similarly to prompt photon production, the transverse momentum spectrum is shown to be dominated by the QCD Compton process, but has virtually no fragmentation or isolation uncertainties. Depending on the orientation of the proton and ion beams and on the use of central or forward detector components, all interesting regions of nuclear effects (shadowing, antishadowing, isospin and EMC effects) can be probed. Ratios of cross sections allow to eliminate theoretical scale and bare-proton parton density errors as well as many experimental systematic uncertainties.

  2. Identification of 19 phthalic acid esters in dairy products by gas chromatography with mass spectrometry.

    Science.gov (United States)

    Wu, Pinggu; Cai, Chenggang; Yang, Dajin; Wang, Liyuan; Zhou, Yan; Shen, Xianghong; Ma, Bingjie; Tang, Jun

    2015-01-01

    A detection method for 19 kinds of phthalic acid ester compounds analyzed by n-hexane/ether/acetonitrile 1:7:8 v/v/v mixed solvent extraction, quick, easy, cheap, effective, rugged, and safe purification and internal standard method of quantitative gas chromatography with mass spectrometry was established. This method can effectively remove interfering materials, such as lipids, fatty acids, and pigments, from dairy products. The 19 kinds of phthalic acid ester compounds were within a 0.025-0.2 mg/kg range, the recovery rate was 65.2-125.7%, relative standard deviation was 7.9-15.4% (n = 6), and the limit of detection was 0.005-0.02 mg/kg. Concentrations of the 19 kinds of phthalic acid ester compounds ranged between 0.01 and 0.12 mg/kg in ten dairy materials and 20 dairy products. The established method is simple, rapid, accurate, and highly sensitive.

  3. Atomic mass dependence of hadron production in semi-inclusive deep inelastic lepton-nucleus scattering

    Institute of Scientific and Technical Information of China (English)

    SONG Li-Hua; LIU Na; DUAN Chun-Gui

    2013-01-01

    Hadron production in lepton-nucleus deep inelastic scattering is studied in a quark energy loss model.The leading-order computations for hadron multiplicity ratios are presented and compared with the selected HERMES pions production data with the quark hadronization occurring outside the nucleus by means of the hadron formation time.It is found that the obtained energy loss per unit length is 0.440±0.013 GeV/fm for an outgoing quark by the global fit.It is confirmed that the atomic mass number dependence of hadron attenuation is theoretically and experimentally in good agreement with the A2/3 power law for quark hadronization occurring outside the nucleus.

  4. Mass-corrections to double-Higgs production & TopoID

    CERN Document Server

    Grigo, Jonathan

    2014-01-01

    We consider power corrections due to a finite top quark mass M_t to the production of a Higgs boson pair within the Standard Model at next-to-leading order (NLO) in QCD. Previous calculations for this process and at this precision were done in the limit of an inifinitely heavy top quark. Our results for the inclusive production cross section at NLO include terms up to O(1/M_t^12). We present the Mathematica package TopoID which for arbitrary processes aims to perform the necessary steps from Feynman diagrams to unrenormalized results expressed in terms of master integrals. We employ it for advancing in this process towards next-to-next-to-leading order (NNLO) where further automatization is needed.

  5. Testing of the new Streptomyces strains for production of phenoloxidases

    Directory of Open Access Journals (Sweden)

    Claudia POPA (UNGUREANU

    2013-12-01

    Full Text Available Thirty wild new strains of filamentous bacteria belonging to the genus Streptomyces isolated from different Romanian soil samples and ten strains from Collection of microorganisms of Bioaliment Research Platform (acronym MIUG were tested and screened for their ability to produce extracellular tyrosinase and laccase. Based on preliminary qualitative screening assays for the extracellular phenoloxidases production carried out by stationary cultivation on Gause agar medium (GMA supplemented with 1% (w/w L-tyrosine, nineteen strains were selected as active producers. Furthermore, a quantitative selection based on active strains ability to produce tyrosinase and laccase by submerged cultivation in liquid Gause salts basal medium supplemented with 1 g L-1 L-tyrosine and 0.001 g L-1 CuSO4, during 168 hours was performed. Results showed that 70% of the Streptomyces strains have a good potential for producing tyrosinase and 30% of strains were remarked for their ability to produce laccase. Moreover, it was observed that, Streptomyces strains coded MIUG 4.89 and MIUG 4.88 from MIUG Collection have the ability to simultaneously produce both enzymes. The effect of temperature and pH on enzymes activity was also investigated. The optimum temperature for both activity (tyrosinase and laccase was found to be 30°C. Laccase was found active over a pH range of 4.0 to 6.0 with maximum activity at pH 5.0. The optimum pH for tyrosinases activity was observed to be around 7.0. The obtained results are important for future applications of Streptomyces phenoloxidases in different areas.

  6. Patch testing with own cosmetics-- prospective study of testing and reporting of adverse effects to the Swedish Medical Products Agency.

    Science.gov (United States)

    Tammela, Monica; Lindberg, Magnus; Isaksson, Marléne; Inerot, Annica; Rudel, Jana; Berne, Berit

    2012-07-01

    The Swedish Medical Products Agency (MPA) provides a voluntary reporting system for adverse reactions to cosmetics. However, the reporting is sparse, and the products involved are sometimes difficult to identify. To investigate how often patients referred for patch testing were tested with the cosmetic products that they had been using themselves, and to improve the reporting to the MPA by the use of photographic documentation of product labels. Consecutive patients at five dermatology departments who were patch tested with their own cosmetics were included. Reports including protocols of positive patch test results for the patients' own cosmetics and photographs/photocopies of product labels were sent to the MPA. Three hundred and sixteen of 948 patients (33%) were tested with their own cosmetics, and 15% of these tested positive with one or more products. The number of reports was more than three times higher than in corresponding periods in earlier years. For 79% of the products, photographs/photocopies of the containers were submitted, and for 30%, batch numbers were submitted. For a substantial number of patients, their own cosmetics were suspected of causing adverse reactions and were therefore tested. During the study, the number of reports to the MPA tripled, and the relevant products were easier to identify. © 2012 John Wiley & Sons A/S.

  7. Impact of mass media exposure and innovation proneness on cocoon production

    Directory of Open Access Journals (Sweden)

    Mir M A

    2015-10-01

    Full Text Available A total of 75 farmers were selected from the four sericulturally important districts viz., Kupwara, Baramulla, Budgam and Pulwama of Kashmir valley (India to study the impact of mass media exposure and changing proneness on the cocoon marketing and cocoon production. Results of study indicated that 58.67 per cent of the respondents had low exposure to mass media, while 34 per cent of them had medium level exposure and only 7.33 per cent enjoyed high level exposure. Change proneness status of stakeholders revealed that overall 50 per cent of respondents belonged to medium category of change proneness; this was followed by low category (42% and high category (8% respectively. With respect to marketing, 67.67 percent of the studied farmers complained about delayed marketing and only 26 per cent of them were satisfied with present marketing operations. Although 51 per cent of the farmers expressed that markets were established in the vicinity of district headquarters, yet 49 per cent were not satisfied with the location of market. Furthermore 90.67 per cent of beneficiaries expressed their displeasure over the competitiveness of marketing and as a result of poor marketing, while 77.67 percent of the rearers expressed that they were not getting remunerative prices for the final produce. On cocoon production side, majority of respondents (72% fall into low category whereas 22.33 and 5.67 percent of them were reported in medium and high category of cocoon production respectively. The cocoon productivity figures also revealed that 30.33 percent of respondents of study area harvested 6-31 kg of green cocoons/ounce of silkworm seed, while 61% percent harvested 31.56 kg/ounce whereas only 8.67 per cent of them harvested 56-81 kg of cocoons/ounce of seed

  8. Anxiolytic effects of short- and long-term administration of cacao mass on rat elevated T-maze test.

    Science.gov (United States)

    Yamada, Takashi; Yamada, Yasushi; Okano, Yasuyo; Terashima, Takehiko; Yokogoshi, Hidehiko

    2009-12-01

    We demonstrated the effects of short- and long-term administration of cacao mass on anxiety in the elevated T-maze test, which is an animal model of anxiety. In the first study, we administered cacao mass (100 mg/100 g body weight) per os and immediately performed the elevated T-maze test. Short-term cacao mass significantly abolished delayed avoidance latency compared with the control but did not change escape latency. This result suggested that cacao mass administration reduced conditional fear-relating behavior. Short-term cacao mass administration did not affect the concentration of brain monoamines, emotion-related neurotransmitters such as norepinephrine, serotonin and dopamine, in the rat brain. In the next study, we fed a cacao mass-containing diet to rats for 2 weeks and performed the elevated T-maze test. Contrary to short-term administration, chronic consumption of cacao mass tended to increase avoidance latency and did not change escape latency. Brain serotonin concentration and its turnover were enhanced by chronic consumption of cacao mass. These results suggested that chronic consumption of cacao did not affect fear-related behavior but was involved in brain monoamine metabolism. In conclusion, we suggest that short-term cacao mass consumption showed an anxiolytic effect but chronic consumption did not.

  9. Resummation prediction on the jet mass spectrum in one-jet inclusive production at the LHC

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Ze Long [School of Physics and State Key Laboratory of Nuclear Physics and Technology,Peking University,Beijing 100871 (China); Li, Chong Sheng [School of Physics and State Key Laboratory of Nuclear Physics and Technology,Peking University,Beijing 100871 (China); Center for High Energy Physics, Peking University,Beijing 100871 (China); Wang, Jian [PRISMA Cluster of Excellence Mainz Institute for Theoretical Physics,Johannes Gutenberg University,D-55099 Mainz (Germany); Wang, Yan [School of Physics and State Key Laboratory of Nuclear Physics and Technology,Peking University,Beijing 100871 (China)

    2015-04-01

    We study the factorization and resummation prediction on the jet mass spectrum in one-jet inclusive production at the LHC based on soft-collinear effective theory. The soft function with anti-k{sub T} algorithm is calculated at next-to-leading order and its validity is demonstrated by checking the agreement between the expanded leading singular terms with the exact fixed-order result. The large logarithms ln{sup n}(m{sub J}{sup 2}/p{sub T}{sup 2}) and the global logarithms ln{sup n}(s{sub 4}/p{sub T}{sup 2}) in the process are resummed to all order at next-to-leading logarithmic and next-to-next-to-leading logarithmic level, respectively. The cross section is enhanced by about 23% from the next-to-leading logarithmic level to next-to-next-to-leading logarithmic level. Comparing our resummation predictions with those from Monte Carlo tool PYTHIA and ATLAS data at the 7 TeV LHC, we find that the peak positions of the jet mass spectra agree with those from PYTHIA at parton level, and the predictions of the jet mass spectra with non-perturbative effects are in coincidence with the ATLAS data. We also show the predictions at the future 13 TeV LHC.

  10. Seesaw majoron model of neutrino mass and novel signals in Higgs boson production at LEP

    Science.gov (United States)

    Díaz, Marco A.; García-Jareño, M. A.; Restrepo, Diego A.; Valle, José W. F.

    1998-08-01

    We perform a careful study of the neutral scalar sector of a model which includes a singlet, a doublet, and a triplet scalar field under SU(2). This model is motivated by neutrino physics, since it is simply the most general version of the seesaw model of neutrino mass generation through spontaneous violation of lepton number. The neutral Higgs sector contains three CP-even and one massive CP-odd Higgs boson A, in addition to the massless CP-odd mojoron J. The weakly interacting majoron remains massless if the breaking of lepton number symmetry is purely spontaneous. We show that the massive CP-odd Higgs boson may invisibly decay to three majorons, as well as to a CP-even Higgs H boson plus a majoron. We consider the associated Higgs production e+e- → Z → HA followed by invisible decays A → JJJ and H → JJ and derive the corresponding limits on masses and coupling that follow from LEP I precision measurements of the invisible Z width. We also study a novel b overlinebb overlinebp T signal predicted by the model, analyze the background and perform a Monte Carlo simulation of the signal in order to illustrate the limits on Higgs boson mass, couplings and branching ratios that follow from that.

  11. Oxidation Products of Ester-Based Oils with and without Antioxidants Identified by Stable Isotope Labelling and Mass Spectrometry

    National Research Council Canada - National Science Library

    Marcella Frauscher; Charlotte Besser; Günter Allmaier; Nicole Dörr

    2017-01-01

    ... is of high importance. In order to reveal their degradation products and processes, a novel approach combining artificial alteration, isotope labelling based on oxidation with 16O2 and 18O2, and mass spectrometry (MS...

  12. Natural Convective Heat and Mass Transfer of Water with Corrosion Products at Super—Critical Pressures under Cooling COnditions

    Institute of Scientific and Technical Information of China (English)

    Pei-XueJiang; Ze-PeiRen; 等

    1993-01-01

    A numerical study is reported of laminar natural convective heat and mass transfer on a vertical cooled plate for water containing metal corrosion products at super-critical pressures.The influence of variable properties at super-critical pressures on natural convertion has been analyzed.The difference between heat and mass transfer under cooling or heating conditions is also discussed and some correlations for heat and mass transfer under cooling conditions are recommended.

  13. Development of heat and mass balance analysis code in out-of-pile hydrogen production system for HTTR heat utilization system (contract research)

    Energy Technology Data Exchange (ETDEWEB)

    Inaba, Yoshitomo; Inagaki, Yoshiyuki; Hayashi, Koji; Suyama, Kazumasa [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment

    1999-03-01

    A heat and mass balance analysis code has been developed to examine test conditions, to investigate transient behavior etc. in the out-of-pile hydrogen production system for the HTTR heat utilization system. The code can analyze temperature, mass and pressure profiles of helium and process gases and behavior of the control system under both static state (case of steady operation) and dynamic state (case of transient operation). This report describes analytical methods, basic equations and constitution of the code, and how to make of the input data, estimate of the analytical results and so on. (author)

  14. Development of heat and mass balance analysis code in out-of-pile hydrogen production system for HTTR heat utilization system (contract research)

    Energy Technology Data Exchange (ETDEWEB)

    Inaba, Yoshitomo; Inagaki, Yoshiyuki; Hayashi, Koji; Suyama, Kazumasa [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment

    1999-03-01

    A heat and mass balance analysis code has been developed to examine test conditions, to investigate transient behavior etc. in the out-of-pile hydrogen production system for the HTTR heat utilization system. The code can analyze temperature, mass and pressure profiles of helium and process gases and behavior of the control system under both static state (case of steady operation) and dynamic state (case of transient operation). This report describes analytical methods, basic equations and constitution of the code, and how to make of the input data, estimate of the analytical results and so on. (author)

  15. Full mass dependence in Higgs boson production in association with jets at the LHC and FCC

    CERN Document Server

    Greiner, Nicolas; Luisoni, Gionata; Schönherr, Marek; Winter, Jan-Christopher

    2017-01-01

    The first computation of Higgs production in association with three jets at NLO in QCD has recently been performed using the effective theory, where the top quark is treated as an infinitely heavy particle and integrated out. This approach is restricted to the regions in phase space where the typical scales are not larger than the top quark mass. Here we investigate this statement at a quantitative level by calculating the leading-order contributions to the production of a Standard Model Higgs boson in association with up to three jets taking full top-quark and bottom-quark mass dependence into account. We find that the transverse momentum of the hardest particle or jet plays a key role in the breakdown of the effective theory predictions, and that discrepancies can easily reach an order of magnitude for transverse momenta of about 1 TeV. The impact of bottom-quark loops are found to be visible in the small transverse momentum region, leading to corrections of up to 5 percent. We further study the impact of m...

  16. Full mass dependence in Higgs boson production in association with jets at the LHC and FCC

    CERN Document Server

    Greiner, Nicolas; Luisoni, Gionata; Schonherr, Marek; Winter, Jan-Christopher

    2016-01-01

    The first computation of Higgs production in association with three jets at NLO in QCD has recently been performed using the effective theory, where the top quark is treated as an infinitely heavy particle and integrated out. This approach is restricted to the regions in phase space where the typical scales are not larger than the top quark mass. Here we investigate this statement at a quantitative level by calculating the leading-order contributions to the production of a Standard Model Higgs boson in association with up to three jets taking full top-quark and bottom-quark mass dependence into account. We find that the transverse momentum of the hardest particle or jet plays a key role in the breakdown of the effective theory predictions, and that discrepancies can easily reach an order of magnitude for transverse momenta of about 1 TeV. The impact of bottom-quark loops are found to be visible in the small transverse momentum region, leading to corrections of up to 5 percent. We further study the impact of m...

  17. Estimation of fluid flow and mass transport properties in a natural fracture using laboratory testing system on mass transport in fractured rock (LABROCK)

    Energy Technology Data Exchange (ETDEWEB)

    Yoshino, Naoto; Uchida, Masahiro [Japan Nuclear Cycle Development Inst., Tokai Works, Tokai, Ibaraki (Japan); Satou, Hisashi [Inspection Development Company Ltd., Tokai, Ibaraki (Japan)

    2003-03-01

    The understanding of mass transport and fluid flow properties in natural rock fractures is important for safety assessment of geological disposal of high level nuclear waste. The authors developed advanced tracer test equipment in which a 50-cm cubic scale rock sample was feasible. The mass transport and fluid flow properties in a single fracture were also examined. The relation among hydraulic, transport and mass balance apertures of a natural single fracture were obtained. Heterogeneity of the aperture distribution was evident, as was the possibility of some major flow line perpendicular to the flow direction. Additionally, the relation between normal stress and each aperture was also obtained by loading normal stress on the fracture. In future, measuring the aperture distribution and establishing the model considering fluid flow and mass transport properties in natural rock fractures will be conducted. (author)

  18. Development and evaluation of magnesium oxide-based ceramics for chamber parts in mass-production plasma etching equipment

    Science.gov (United States)

    Kasashima, Yuji; Tsutsumi, Kota; Mitomi, Shinzo; Uesugi, Fumihiko

    2017-06-01

    In mass-production plasma etching equipment, the corrosion of ceramic chamber parts reduces the production yield of LSI and overall equipment effectiveness (OEE) owing to contamination, short useful life, and particle generation. Novel ceramics that can improve the production yield and OEE are highly required. We develop magnesium oxide (MgO)-based ceramics and evaluate them under mass-production plasma etching conditions. The results of this study indicate that the developed MgO-based ceramics with high mechanical properties and low electric resistivity have a higher resistance to corrosion in plasma etching using CF4 gas than Si and conventional ceramic materials such as aluminum oxide and yttrium oxide.

  19. Standard test methods for chemical, mass spectrometric, spectrochemical, nuclear, and radiochemical analysis of nuclear-grade plutonium metal

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2004-01-01

    1.1 These test methods cover procedures for the chemical, mass spectrometric, spectrochemical, nuclear, and radiochemical analysis of nuclear-grade plutonium metal to determine compliance with specifications.

  20. Soft gluon resummation at fixed invariant mass for associated $t\\bar{t}H$ production at the LHC

    CERN Document Server

    Kulesza, Anna; Stebel, Tomasz; Theeuwes, Vincent

    2016-01-01

    In the following we present our results on resummation of invariant mass threshold corrections for the $2 \\to 3$ type hadronic production processes in the Mellin moment space formalism. This method is applied to the associated Higgs boson production process $pp \\to t \\bar{t} H$ at the LHC. The results for the total cross section, the differential distribution with respect to the invariant mass and their uncertainties are presented.

  1. Mass spectrometry for the determination of fission products 135Cs, 137Cs and 90Sr: A review of methodology and applications

    Science.gov (United States)

    Bu, Wenting; Zheng, Jian; Liu, Xuemei; Long, Kaiming; Hu, Sheng; Uchida, Shigeo

    2016-05-01

    The radioactive fission products 135Cs, 137Cs and 90Sr have been released into the environment by human activities such as nuclear weapon tests, nuclear fuel reprocessing and nuclear power plant accidents. Monitoring of these radionuclides is important for dose assessment. Moreover, the 135Cs/137Cs isotopic ratio can be used as an important long-term fingerprint for radioactive source identification as it varies with weapon, reactor and fuel types. In recent years, mass spectrometry has become a powerful method for the determination of 135Cs, 137Cs and 90Sr in environmental samples. Mass spectrometry is characterized by the high sensitivity and low detection limit and the relatively shorter sample preparation and analysis times compared with radiometric methods. However, the mass spectrometric determination of radiocesium and 90Sr is affected by the peak tailings of the stable nuclides 133Cs and 88Sr, respectively, and the related isobaric and polyatomic interferences. Chemical separation and optimization of the mass spectrometry instrumental setup are strongly needed prior to the mass spectrometry detection. In this paper, we have reviewed the published works about the determination of 135Cs, 137Cs and 90Sr by mass spectrometry. The mass spectrometric techniques we cover are resonance ionization mass spectrometry (RIMS), thermal ionization mass spectrometry (TIMS), accelerator mass spectrometry (AMS) and inductively coupled plasma mass spectrometry (ICP-MS). For each technique, the principles or strategies used for the analysis of these radionuclides are discussed; these included the abundance sensitivity, ways to suppress the interference signals, and the instrumental setup. In particular, the chemical procedures for eliminating the interferences are also summarized. To date, triple quadrupole ICP-MS (ICP-QQQ) showed great ability for the analysis of these radionuclides and the detection limits were as low as 0.01 pg/mL levels. Finally, some investigations on the

  2. Problems of Automatic Test of Insulation in Cable Production

    Science.gov (United States)

    Red'ko, V. V.; Leonov, A. P.; Red'ko, L. A.; Bolgova, V. A.

    2016-01-01

    The article presents a qualitative and quantitative assessment of cable products insulation defects that can be reliably detected by means of the electrosparking control during the cable production process. The performance potential of technological control is evaluated: the limit of reliable detection of defective places in insulation taking into account the technical capabilities of modern control devices is marked.

  3. A Test of Color-Octet Heavy Quarkonium Production Mechanism

    Institute of Scientific and Technical Information of China (English)

    DUAN Chun-Gui; YAN Zhan-Yuan; HE Zhen-Min

    2001-01-01

    Using the scale evolution of nuclear parton distributions,the contribution of color-octet heavy quarkonium production mechanism to the P + Fe → J/ψ + γ + X process in calculated and discussed.Comparing our theoretical results with the future experimental data,the color-octet heavy quarkonium production mechanism can be examined.``

  4. The influence of the production process on mechanical properties of rubber testing samples

    OpenAIRE

    Škrobák, Adam; STANĚK, Michal; Maňas, David; Ovsík, Martin; Šenkeřík, Vojtěch; Řezníček, Martin

    2014-01-01

    The article deals with the influence of production technology on mechanical properties of rubber testing samples. In practice, rubber testing samples are cut out from a compression molded sheet, also in case of testing of rubber compounds appointed for injection molding. However, the different way of the preparation of testing samples and the production itself may have a negative effect on the mechanical properties of the final product. Thus the article judges, to what extent the mechanical p...

  5. Mass SAR Test of Cell Phone%手机批量SAR测试方案

    Institute of Scientific and Technical Information of China (English)

    何毅; 范伟杰

    2013-01-01

    SAR is internationally adopted to measure the radiation, but the SAR test of cell phone is a complicated process. Based on the fundamental knowledge of cell phone SAR and the French SAGEM Laboratory Testing System, this paper presents the fundamental theories and key points of the Laboratory Testing System. The major factors which influence the cell phone SAR are analyzed from the aspects of the different circumstances of laboratory environment and the SAR test results of different cell phone models; the correlation between the factors and the SAR is studied. The cell phone SAR is simulated indirectly and a feasible scheme is obtained for the mass SAR test of cell phones.%国际上通行的方法是用比吸收率(SAR)来衡量手机辐射大小,但是手机SAR的测试又是一个非常复杂的过程。本文在介绍手机SAR的基本知识和法国SAGEM实验室测试系统的基础上,对实验室SAR测试的基本原理和要点做了归纳,通过对实验室环境下对各种情况、各个型号手机SAR的测试结果分析,分析手机SAR的主要影响因素,通过对这些影响因素与SAR关系的研究;来间接模拟手机SAR,以获得可用于批量手机SAR测试的可行性方案。

  6. Carbon isotope ratio mass spectrometry for detection of endogenous steroid use: a testing strategy.

    Science.gov (United States)

    Ahrens, Brian D; Butch, Anthony W

    2013-07-01

    Isotope ratio mass spectrometry (IRMS) testing is performed to determine if an atypical steroid profile is due to administration of an endogenous steroid. Androsterone (Andro) and etiocholanolone (Etio), and/or the androstanediols (5α- and 5β-androstane-3α,17β-diol) are typically analyzed by IRMS to determine the (13) C/(12) C ratio. The ratios of these target compounds are compared to the (13) C/(12) C ratio of an endogenous reference compound (ERC) such as 5β-pregnane-3α,20α-diol (Pdiol). Concentrations of Andro and Etio are high so (13) C/(12) C ratios can easily be measured in most urine samples. Despite the potentially improved sensitivity of the androstanediols for detecting the use of some testosterone formulations, additional processing steps are often required that increase labour costs and turnaround times. Since this can be problematic when performing large numbers of IRMS measurements, we established thresholds for Andro and Etio that can be used to determine the need for additional androstanediol testing. Using these criteria, 105 out of 2639 urine samples exceeded the Andro and/or Etio thresholds, with 52 of these samples being positive based on Andro and Etio IRMS testing alone. The remaining 53 urine samples had androstanediol IRMS testing performed and 3 samples were positive based on the androstanediol results. A similar strategy was used to establish a threshold for Pdiol to identify athletes with relatively (13) C-depleted values so that an alternative ERC can be used to confirm or establish a true endogenous reference value. Adoption of a similar strategy by other laboratories can significantly reduce IRMS sample processing and analysis times, thereby increasing testing capacity.

  7. Testing the cosmic distance duality with X-ray gas mass fraction and supernovae data

    CERN Document Server

    Goncalves, R S; Alcaniz, J S

    2011-01-01

    In this paper we discuss a new cosmological model-independent test for the cosmic distance duality relation (CDDR), $\\eta = D_{L}(L)(1+z)^{-2}/D_{A}(z)=1$, where $D_{A}(z)$ and $D_{L}(z)$ are the angular and luminosity distances, respectively. Using the general expression for X-ray gas mass fraction ($f_{gas}$) of galaxy clusters, $f_{gas} \\propto D_L{D_A}^{1/2}$, we show that $f_{gas}$ observations jointly with type Ia supernovae (SNe Ia) data furnish a validity test for the CDDR. To perform our analysis we use 38 $f_{gas}$ measurements recently studied by two groups considering different assumptions to describe the clusters (La Roque {\\it{et al.}} 2006 and Ettori {\\it{et al.}} 2009) and two subsamples of SNe Ia distance lumonosity extracted from the Union2 compilation. In our test we consider the $\\eta$ parameter as a function of the redshift parameterized by two different functional forms. It is found that the La Roque {\\it{et al.}} (2006) sample is in perfect agreement with the duality relation ($\\eta = 1...

  8. A Unified Theory of Impact Crises and Mass Extinctions: Quantitative Tests

    Science.gov (United States)

    Rampino, Michael R.; Haggerty, Bruce M.; Pagano, Thomas C.

    1997-01-01

    Several quantitative tests of a general hypothesis linking impacts of large asteroids and comets with mass extinctions of life are possible based on astronomical data, impact dynamics, and geological information. The waiting of large-body impacts on the Earth derive from the flux of Earth-crossing asteroids and comets, and the estimated size of impacts capable of causing large-scale environmental disasters, predict that impacts of objects greater than or equal to 5 km in diameter (greater than or equal to 10 (exp 7) Mt TNT equivalent) could be sufficient to explain the record of approximately 25 extinction pulses in the last 540 Myr, with the 5 recorded major mass extinctions related to impacts of the largest objects of greater than or equal to 10 km in diameter (greater than or equal to 10(exp 8) Mt Events). Smaller impacts (approximately 10 (exp 6) Mt), with significant regional environmental effects, could be responsible for the lesser boundaries in the geologic record.

  9. Asteroseismic test of rotational mixing in low-mass white dwarfs

    CERN Document Server

    Istrate, A G; Gianninas, A; Grassitelli, L; Marchant, P; Tauris, T M; Langer, N

    2016-01-01

    We exploit the recent discovery of pulsations in mixed-atmosphere (He/H), extremely low-mass white dwarf precursors (ELM proto-WDs) to test the proposition that rotational mixing is a fundamental process in the formation and evolution of low-mass helium core white dwarfs. Rotational mixing has been shown to be a mechanism able to compete efficiently against gravitational settling, thus accounting naturally for the presence of He, as well as traces of metals such as Mg and Ca, typically found in the atmospheres of ELM proto-WDs. Here we investigate whether rotational mixing can maintain a sufficient amount of He in the deeper driving region of the star, such that it can fuel, through HeII-HeIII ionization, the observed pulsations in this type of stars. Using state-of-the-art evolutionary models computed with MESA, we show that rotational mixing can indeed explain qualitatively the very existence and general properties of the known pulsating, mixed-atmosphere ELM proto-WDs. Moreover, such objects are very likel...

  10. Testing mixed action approaches to meson spectroscopy with twisted mass sea quarks

    CERN Document Server

    Berlin, Joshua; Wagner, Marc

    2013-01-01

    We explore and compare three mixed action setups with Wilson twisted mass sea quarks and different valence quark actions: (1) Wilson twisted mass, (2) Wilson twisted mass + clover and (3) Wilson + clover. Our main goal is to reduce lattice discretization errors in mesonic spectral quantities, in particular to reduce twisted mass parity and isospin breaking.

  11. Automatic Rayleigh scattering mapping system for optical quality evaluation of test masses for gravity wave detectors

    Science.gov (United States)

    Yan, Zewu; Zhao, Chunnong; Ju, Li; Gras, Slawomir; Baringa, Pablo; Blair, David G.

    2005-01-01

    This article describes an automatic Rayleigh scattering mapping system (ARSMS), which enables quantitative high-resolution three-dimensional mapping of inhomogeneities in optical materials. The ARSMS allows large high-grade test mass samples for gravitational wave detectors to be evaluated to ensure that an adequate low level of scattering is achieved. The ARSMS combines proprietary camera software with data analysis software and control software to achieve fully automatic operation with graphical user interfaces. This article presents the instrument concept and examples of the output. Device mapping in all degrees of freedom is shown to be better than 0.5mm, with scattering sensitivity better than 0.5ppm/cm. This system is able to scan and map the Rayleigh scattering of large samples in both of cylindrical and rectangular samples using cylindrical and Cartesian coordinates.

  12. Effects of humidity on the interaction between a fused silica test mass and an electrostatic drive

    Energy Technology Data Exchange (ETDEWEB)

    Koptsov, D.V., E-mail: kopcov@physics.msu.ru; Prokhorov, L.G.; Mitrofanov, V.P.

    2015-10-23

    Interaction of a fused silica test mass with electric field of an electrostatic drive with interdigitated electrodes and influence of ambient air humidity on this interaction are investigated. The key element of the experimental setup is the fused silica torsional oscillator. Time dependent increase of the torque acting on the oscillator's plate after application of DC voltage to the drive is demonstrated. The torque relaxation is presumably caused by the redistribution of electric charges on the fused silica plate. The numerical model has been developed to compute the time evolution of the plate's surface charge distribution and the corresponding torque. - Highlights: • Interaction between a fused silica plate and an electrostatic drive was investigated. • The interaction force is time and relative humidity dependent. • Numerical model of the interaction was developed. • Charge redistribution is shown to be the cause of the interaction force evolution.

  13. Standard test methods for chemical, mass spectrometric, spectrochemical, nuclear, and radiochemical analysis of nuclear-grade plutonium nitrate solutions

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2010-01-01

    1.1 These test methods cover procedures for the chemical, mass spectrometric, spectrochemical, nuclear, and radiochemical analysis of nuclear-grade plutonium nitrate solutions to determine compliance with specifications. 1.2 The analytical procedures appear in the following order: Sections Plutonium by Controlled-Potential Coulometry Plutonium by Amperometric Titration with Iron(II) Plutonium by Diode Array Spectrophotometry Free Acid by Titration in an Oxalate Solution 8 to 15 Free Acid by Iodate Precipitation-Potentiometric Titration Test Method 16 to 22 Uranium by Arsenazo I Spectrophotometric Test Method 23 to 33 Thorium by Thorin Spectrophotometric Test Method 34 to 42 Iron by 1,10-Phenanthroline Spectrophotometric Test Method 43 to 50 Impurities by ICP-AES Chloride by Thiocyanate Spectrophotometric Test Method 51 to 58 Fluoride by Distillation-Spectrophotometric Test Method 59 to 66 Sulfate by Barium Sulfate Turbidimetric Test Method 67 to 74 Isotopic Composition by Mass Spectrom...

  14. 76 FR 9028 - Guidance for Industry: Potency Tests for Cellular and Gene Therapy Products; Availability

    Science.gov (United States)

    2011-02-16

    ... Industry: Potency Tests for Cellular and Gene Therapy Products'' dated January 2011. The guidance document provides manufacturers of cellular and gene therapy (CGT) products with recommendations for developing... document entitled ``Guidance for Industry: Potency Tests for Cellular and Gene Therapy Products''...

  15. 77 FR 30887 - Amendments to Sterility Test Requirements for Biological Products; Correction

    Science.gov (United States)

    2012-05-24

    ... Test Requirements for Biological Products; Correction AGENCY: Food and Drug Administration, HHS. ACTION... manufacturers of biological products greater flexibility, as appropriate, and encourages use of the most appropriate and state-of-the-art test methods for assuring the safety of biological products. The rule...

  16. Fast Screening of Chicken Egg Lysozyme in White Wine Products by Extractive Electrospray Ionization Mass Spectrometry

    Institute of Scientific and Technical Information of China (English)

    ZHOU Zhi-quan; JIANG Jie; LI Ming; ZHAO Zhan-feng; FU Jun

    2012-01-01

    Fast detection of trace lysozyme,one of the most important food allergens in white wine samples,was achieved by extractive electrospray ionization mass spectrometry without sample pretreatment in this study.The multiply-charged ions of m/z 1587 were chosen for the quantitative detection of lysozyme in white wine,showing linear dynamic signal responses in a range of 5-75 μg/mL with a linearity coefficient of 0.999 and an acceptable relative standard deviation(RSD)of 8.0%-15.0% for directly measuring lysozyme in the complex food samples.The limit of detection for lysozyme in white wine sample was calculated to be 5 μg/mL,which was lower than the amounts that can provoke allergic reactions(oral test with 3 mg or labial test with 1 mg/mL).A single sample analysis was completed within 1 min.The data demonstrate that extractive electrospray ionization mass spectrometry is a useful tool for fast screening lysozyme in the complex matrix,showing promising application in the rapid detection of food allergen.

  17. IR Camera Report for the 7 Day Production Test

    Energy Technology Data Exchange (ETDEWEB)

    Holloway, Michael Andrew [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-02-22

    The following report gives a summary of the IR camera performance results and data for the 7 day production run that occurred from 10 Sep 2015 thru 16 Sep 2015. During this production run our goal was to see how well the camera performed its task of monitoring the target window temperature with our improved alignment procedure and emissivity measurements. We also wanted to see if the increased shielding would be effective in protecting the camera from damage and failure.

  18. Methodology for the design, production, and test of plastic optical displacement sensors

    Science.gov (United States)

    Rahlves, Maik; Kelb, Christian; Reithmeier, Eduard; Roth, Bernhard

    2016-08-01

    Optical displacement sensors made entirely from plastic materials offer various advantages such as biocompatibility and high flexibility compared to their commonly used electrical and glass-based counterparts. In addition, various low-cost and large-scale fabrication techniques can potentially be utilized for their fabrication. In this work we present a toolkit for the design, production, and test of such sensors. Using the introduced methods, we demonstrate the development of a simple all-optical displacement sensor based on multimode plastic waveguides. The system consists of polymethylmethacrylate and cyclic olefin polymer which serve as cladding and core materials, respectively. We discuss several numerical models which are useful for the design and simulation of the displacement sensors as well as two manufacturing methods capable of mass-producing such devices. Prior to fabrication, the sensor layout and performance are evaluated by means of a self-implemented ray-optical simulation which can be extended to various other types of sensor concepts. Furthermore, we discuss optical and mechanical test procedures as well as a high-precision tensile testing machine especially suited for the characterization of the opto-mechanical performance of such plastic optical displacement sensors.

  19. Blind testing of cross-linking/mass spectrometry hybrid methods in CASP11.

    Science.gov (United States)

    Schneider, Michael; Belsom, Adam; Rappsilber, Juri; Brock, Oliver

    2016-09-01

    Hybrid approaches combine computational methods with experimental data. The information contained in the experimental data can be leveraged to probe the structure of proteins otherwise elusive to computational methods. Compared with computational methods, the structures produced by hybrid methods exhibit some degree of experimental validation. In spite of these advantages, most hybrid methods have not yet been validated in blind tests, hampering their development. Here, we describe the first blind test of a specific cross-link based hybrid method in CASP. This blind test was coordinated by the CASP organizers and utilized a novel, high-density cross-linking/mass-spectrometry (CLMS) approach that is able to collect high-density CLMS data in a matter of days. This experimental protocol was developed in the Rappsilber laboratory. This approach exploits the chemistry of a highly reactive, photoactivatable cross-linker to produce an order of magnitude more cross-links than homobifunctional cross-linkers. The Rappsilber laboratory generated experimental CLMS data based on this protocol, submitted the data to the CASP organizers which then released this data to the CASP11 prediction groups in a separate, CLMS assisted modeling experiment. We did not observe a clear improvement of assisted models, presumably because the properties of the CLMS data-uncertainty in cross-link identification and residue-residue assignment, and uneven distribution over the protein-were largely unknown to the prediction groups and their approaches were not yet tailored to this kind of data. We also suggest modifications to the CLMS-CASP experiment and discuss the importance of rigorous blind testing in the development of hybrid methods. Proteins 2016; 84(Suppl 1):152-163. © 2016 The Authors Proteins: Structure, Function, and Bioinformatics Published by Wiley Periodicals, Inc.

  20. 78 FR 51678 - Market Tests of Experimental Postal Products

    Science.gov (United States)

    2013-08-21

    ... the label that includes a tracking number and a QR code. Id. This enables the mailer to check the... the QR code with a mobile device. Id. The market test began on December 10, 2011 with 50 test... amend chapter III of title 39 of the Code of Federal Regulations as follows: PART 3001--RULES...

  1. 21 CFR 355.70 - Testing procedures for fluoride dentifrice drug products.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Testing procedures for fluoride dentifrice drug... Procedures § 355.70 Testing procedures for fluoride dentifrice drug products. (a) A fluoride dentifrice drug... biological tests are labeled Biological Testing Procedures for Fluoride Dentifrices; these testing procedures...

  2. Setup, tests and results for the ATLAS TileCal Read Out Driver production

    CERN Document Server

    Valero, Alberto; Castillo, V; Cuenca, C; Ferrer, A; Fullana, E; González, V; Higón, E; Munar, A; Poveda, J; Ruiz-Martínez, A; Salvachúa, B; Sanchís, E; Solans, C; Soret, J; Torres, J; Valls, J A

    2007-01-01

    In this paper we describe the performance and test results of the production of the 38 ATLAS TileCal Read Out Drivers (RODs). We first describe the basic hardware specifications and firmware functionality of the modules, the test-bench setup used for production and the test procedure to qualify the boards. We then finally show and discuss the performance results.

  3. 46 CFR 160.026-6 - Sampling, inspection, and tests of production lots.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 6 2010-10-01 2010-10-01 false Sampling, inspection, and tests of production lots. 160... Hermetically Sealed Containers), for Merchant Vessels § 160.026-6 Sampling, inspection, and tests of production... 160.026-6(d1)—Sampling for Laboratory Tests Lot size Number of sets of samples to be selected...

  4. Recent Developments in Cell Vibration Testing at ABSL Space Products

    Science.gov (United States)

    Roberts, Sam; Thwaite, Carl

    2014-08-01

    This paper will describe vibration testing performed at ABSL in recent years on 18650 lithium-ion cells, focussing on work done to expand knowledge of the newest cells (the HCM and NL cells) under random vibration loads. COTS cells as used by ABSL are not necessarily designed for vibration tolerance, and so understanding the conditions that cause failures, and the precise failure modes, is a critical activity.The approach used for cell testing will be described, including the test setup and overall test and analysis flow. In particular, two different approaches (using fixed and resonating interfaces) will be described. The results of survival testing performed on HCM and NL cells will be presented. In addition, the damping behaviour of the HC cell will be described.

  5. Standard test method for analysis of isotopic composition of uranium in nuclear-grade fuel material by quadrupole inductively coupled plasma-mass spectrometry

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2000-01-01

    1.1 This test method is applicable to the determination of the isotopic composition of uranium (U) in nuclear-grade fuel material. The following isotopic weight percentages are determined using a quadrupole inductively coupled plasma-mass spectrometer (Q-ICP-MS): 233U, 234U, 235U, 236U, and 238U. The analysis can be performed on various material matrices after acid dissolution and sample dilution into water or dilute nitric (HNO3) acid. These materials include: fuel product, uranium oxide, uranium oxide alloys, uranyl nitrate (UNH) crystals, and solutions. The sample preparation discussed in this test method focuses on fuel product material but may be used for uranium oxide or a uranium oxide alloy. Other preparation techniques may be used and some references are given. Purification of the uranium by anion-exchange extraction is not required for this test method, as it is required by other test methods such as radiochemistry and thermal ionization mass spectroscopy (TIMS). This test method is also described i...

  6. PETER: A Hardware Simulator for the Test Mass-GRS System of LISA Pathfinder

    Science.gov (United States)

    Marconi, L.; Stanga, R.; Bassan, M.; De Marchi, F.; Pucacco, G.; Visco, M.; Di Fiore, L.; De Rosa, R.; Garufi, F.

    2013-01-01

    Each LISA PathFinder test mass (TM) will be sensitive to forces along all its 6 Degrees of Freedom (DoFs). Extensive ground testing is required in order to evaluate the influence of cross-talks from the read-out and actuator channels. In the INFN laboratory of Firenze we have developed a facility for a good representation of the free fall conditions of the TM on flight. A hollow replica of a TM hanging from a double torsion pendulum can move inside a Gravitational Reference Sensor (GRS) with quasi free fall condition on two Dofs, in the frequency band (0.1 ÷ 100)mHz. On both DoFs, the target residual accelerations (yet to be achieved) at the low end frequency range are ≤ 3 × 10-13ms-2, limited by the thermal noise of the fibres. At higher frequencies, the sensitivity is limited by the readout noise of the readout, a replica of the flight electronics. After a long commissioning, we are now in operating conditions, and can carry out a series of experiments to better qualify the interaction between TM and GRS. In this paper we will show some significant qualification measurements and a first scientific measurements, i.e. the measurement and compensation of the DC bias in the GRS using two independent channels, as well as a measurement of the residual acceleration of the translational DoF, with the feedback loop closed on the rotational one, and viceversa.

  7. Floating wetland islands as a method of nitrogen mass reduction: results of a 1 year test.

    Science.gov (United States)

    Vázquez-Burney, Rafael; Bays, James; Messer, Ryan; Harris, Jeffrey

    2015-01-01

    Floating wetland islands (FWIs) were tested in Pasco County, Florida, as a method of reducing total nitrogen (TN) in reclaimed water during reservoir storage. The Pasco County Master Reuse System (PCMRS) is a regional reclaimed-water transmission and distribution system providing wastewater effluent disposal for the county. Total daily mass loading from reclaimed water is limited by nitrogen content in the PCMRS watershed. To test TN reduction efficacy, 20 FWIs were constructed, installed, and monitored in a lined pond receiving PCMRS reclaimed water. In total, 149 m2 of FWIs were installed, distributed as a connected network covering 1,122 m2, or 7% of pond area. Pond hydraulic residence time averaged 15.7 days. Treatment performance was assessed during three consecutive periods: establishment (first 6 months of grow-in), performance (8 months immediately following grow-in), and control (3 months after the FWIs were removed from the pond). The FWIs enhanced pond nitrogen removal capacity by 32%. The primary effect of the FWIs was to decrease organic nitrogen in the pond outflow. By evaluating the difference between the performance and control periods, an incremental TN removal rate for the FWIs was calculated to be 4.2 kg N/m2 FWI per year.

  8. Development of mass production technology for enhancing wearability of hair clippers blades

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jae Hyung; Park, Jae Won; Lee, Jae Sang; Son, Chang Won

    2003-08-01

    A hair clipper that uses for cutting hairs and pet furs comprises mainly of cutting blades, motor, and body. The most important part among these is the cutting blade, because it often determines the life time of the hair clipper. The material of cutting blade is the stainless steel such as SS440A or SS420 and it is not subjected to the severe abrasive condition. On the bases of the previous studies that showed the enhanced wear resistance upon implanting N ions into the surface of the blade, a facility for mass production of the N ion implanted hair cutting blade has been developed and a process qualification has been performed and established in this project.

  9. PDMAA Hydrogel Coated U-Bend Humidity Sensor Suited for Mass-Production.

    Science.gov (United States)

    Kelb, Christian; Körner, Martin; Prucker, Oswald; Rühe, Jürgen; Reithmeier, Eduard; Roth, Bernhard

    2017-03-04

    We present a full-polymer respiratory monitoring device suited for application in environments with strong magnetic fields (e.g., during an MRI measurement). The sensor is based on the well-known evanescent field method and consists of a 1 mm plastic optical fiber with a bent region where the cladding is removed and the fiber is coated with poly-dimethylacrylamide (PDMAA). The combination of materials allows for a mass-production of the device by spray-coating and enables integration in disposable medical devices like oxygen masks, which we demonstrate here. We also present results of the application of an autocorrelation-based algorithm for respiratory frequency determination that is relevant for real applications of the device.

  10. PDMAA Hydrogel Coated U-Bend Humidity Sensor Suited for Mass-Production

    Directory of Open Access Journals (Sweden)

    Christian Kelb

    2017-03-01

    Full Text Available We present a full-polymer respiratory monitoring device suited for application in environments with strong magnetic fields (e.g., during an MRI measurement. The sensor is based on the well-known evanescent field method and consists of a 1 mm plastic optical fiber with a bent region where the cladding is removed and the fiber is coated with poly-dimethylacrylamide (PDMAA. The combination of materials allows for a mass-production of the device by spray-coating and enables integration in disposable medical devices like oxygen masks, which we demonstrate here. We also present results of the application of an autocorrelation-based algorithm for respiratory frequency determination that is relevant for real applications of the device.

  11. Toward understanding amines and their degradation products from postcombustion CO2 capture processes with aerosol mass spectrometry.

    Science.gov (United States)

    Ge, Xinlei; Shaw, Stephanie L; Zhang, Qi

    2014-05-06

    Amine-based postcombustion CO2 capture (PCCC) is a promising technique for reducing CO2 emissions from fossil fuel burning plants. A concern of the technique, however, is the emission of amines and their degradation byproducts. To assess the environmental risk of this technique, standardized stack sampling and analytical methods are needed. Here we report on the development of an integrated approach that centers on the application of a high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS) for characterizing amines and PCCC-relevant species. Molecular characterization is achieved via ion chromatography (IC) and electrospray ionization high-resolution mass spectrometry (ESI-MS). The method has been optimized, particularly, by decreasing the AMS vaporizer temperature, to gain quantitative information on the elemental composition and major nitrogen-containing species in laboratory-degraded amine solvents commonly tested for PCCC applications, including ethanolamine (MEA), methyldiethanolamine (MDEA), and piperazine (PIP). The AMS-derived nitrogen-to-carbon (N/C) ratios for the degraded solvent and product mixtures agree well with the results from a total organic carbon and total nitrogen (TOC/TN) analyzer. In addition, marker ions identified in the AMS spectra are used to estimate the mass contributions of individual species. Overall, our results indicate that this new approach is suitable for characterizing PCCC-related mixtures as well as organic nitrogen species in other sample types. As an online instrument, AMS can be used for both real-time characterization of emissions from operating PCCC plants and ambient particles in the vicinity of the facilities.

  12. Testing indirect effect of consumer attitudes toward a product

    DEFF Research Database (Denmark)

    Hrubá, Renata; Sudzina, Frantisek

    2016-01-01

    and on the indirect and direct effects of the perception of information through information behavior and the use of the model ordered. It is proposed that consumer levels of product familiarity of attributes affects behavior. Consumer attitudes towards agri-food products and behaviour were analyzed through...... a questionnaire in 2010-2011. The model is estimated using probit analysis to predict relationship between producer and consumer in decision-making when buying a new type of cheese and to examine consumer attitudes toward food origins and nutrient food security. It can be concluded that the indirect effect (e......The number of farmers´ markets has been increasing all around the world. This growth in the popularity of farmers´ markets has been attributed to factors of changing consumer interest in local traditional or innovative food products. This paper focuses on familiarity bias in the Czech dairy market...

  13. Measurement of the W mass in $e^{+}e^{-}$ collisions at production threshold

    CERN Document Server

    Barate, R; Décamp, D; Ghez, P; Goy, C; Lees, J P; Lucotte, A; Minard, M N; Nief, J Y; Pietrzyk, B; Casado, M P; Chmeissani, M; Comas, P; Crespo, J M; Delfino, M C; Fernández, E; Fernández-Bosman, M; Garrido, L; Juste, A; Martínez, M; Miquel, R; Mir, L M; Orteu, S; Padilla, C; Park, I C; Pascual, A; Perlas, J A; Riu, I; Sánchez, F; Teubert, F; Colaleo, A; Creanza, D; De Palma, M; Gelao, G; Iaselli, Giuseppe; Maggi, G; Maggi, M; Marinelli, N; Nuzzo, S; Ranieri, A; Raso, G; Ruggieri, F; Selvaggi, G; Silvestris, L; Tempesta, P; Tricomi, A; Zito, G; Huang, X; Lin, J; Ouyang, Q; Wang, T; Xie, Y; Xu, R; Xue, S; Zhang, J; Zhang, L; Zhao, W; Abbaneo, D; Alemany, R; Bazarko, A O; Becker, U; Bright-Thomas, P G; Cattaneo, M; Cerutti, F; Drevermann, H; Forty, Roger W; Frank, M; Hagelberg, R; Harvey, J; Janot, P; Jost, B; Kneringer, E; Knobloch, J; Lehraus, Ivan; Lutters, G; Mato, P; Minten, Adolf G; Moneta, L; Pacheco, A; Pusztaszeri, J F; Ranjard, F; Rensing, P E; Rizzo, G; Rolandi, Luigi; Schlatter, W D; Schmitt, M; Schneider, O; Tejessy, W; Tomalin, I R; Wachsmuth, H W; Wagner, A; Ajaltouni, Ziad J; Barrès, A; Boyer, C; Falvard, A; Ferdi, C; Gay, P; Guicheney, C; Henrard, P; Jousset, J; Michel, B; Monteil, S; Montret, J C; Pallin, D; Perret, P; Podlyski, F; Proriol, J; Rosnet, P; Rossignol, J M; Fearnley, Tom; Hansen, J B; Hansen, J D; Hansen, J R; Hansen, P H; Nilsson, B S; Rensch, B; Wäänänen, A; Daskalakis, G; Kyriakis, A; Markou, C; Simopoulou, Errietta; Vayaki, Anna; Blondel, A; Brient, J C; Machefert, F P; Rougé, A; Rumpf, M; Valassi, Andrea; Videau, H L; Focardi, E; Parrini, G; Zachariadou, K; Corden, M; Georgiopoulos, C H; Jaffe, D E; Antonelli, A; Bencivenni, G; Bologna, G; Bossi, F; Campana, P; Capon, G; Casper, David William; Chiarella, V; Felici, G; Laurelli, P; Mannocchi, G; Murtas, F; Murtas, G P; Passalacqua, L; Pepé-Altarelli, M; Curtis, L; Dorris, S J; Halley, A W; Knowles, I G; Lynch, J G; O'Shea, V; Raine, C; Scarr, J M; Smith, K; Teixeira-Dias, P; Thompson, A S; Thomson, E; Thomson, F; Turnbull, R M; Geweniger, C; Graefe, G; Hanke, P; Hansper, G; Hepp, V; Kluge, E E; Putzer, A; Schmidt, M; Sommer, J; Tittel, K; Werner, S; Wunsch, M; Beuselinck, R; Binnie, David M; Cameron, W; Dornan, Peter J; Girone, M; Goodsir, S M; Martin, E B; Morawitz, P; Moutoussi, A; Nash, J; Sedgbeer, J K; Stacey, A M; Williams, M D; Dissertori, G; Ghete, V M; Girtler, P; Kuhn, D; Rudolph, G; Betteridge, A P; Bowdery, C K; Colrain, P; Crawford, G; Finch, A J; Foster, F; Hughes, G; Jones, R W L; Sloan, Terence; Whelan, E P; Williams, M I; Hoffmann, C; Jakobs, K; Kleinknecht, K; Quast, G; Renk, B; Rohne, E; Sander, H G; Van Gemmeren, P; Zeitnitz, C; Aubert, Jean-Jacques; Benchouk, C; Bonissent, A; Bujosa, G; Calvet, D; Carr, J; Coyle, P; Diaconu, C A; Konstantinidis, N P; Leroy, O; Motsch, F; Payre, P; Rousseau, D; Talby, M; Sadouki, A; Thulasidas, M; Tilquin, A; Trabelsi, K; Aleppo, M; Ragusa, F; Berlich, R; Blum, Walter; Büscher, V; Dietl, H; Dydak, Friedrich; Ganis, G; Gotzhein, C; Kroha, H; Lütjens, G; Lutz, Gerhard; Männer, W; Moser, H G; Richter, R H; Rosado-Schlosser, A; Schael, S; Settles, Ronald; Seywerd, H C J; Saint-Denis, R; Stenzel, H; Wiedenmann, W; Wolf, G; Boucrot, J; Callot, O; Chen, S; Cordier, A; Davier, M; Duflot, L; Grivaz, J F; Heusse, P; Höcker, A; Jacholkowska, A; Jacquet, M; Kim, D W; Le Diberder, F R; Lefrançois, J; Lutz, A M; Nikolic, I A; Schune, M H; Simion, S; Tournefier, E; Veillet, J J; Videau, I; Zerwas, D; Azzurri, P; Bagliesi, G; Batignani, G; Bettarini, S; Bozzi, C; Calderini, G; Carpinelli, M; Ciocci, M A; Ciulli, V; Dell'Orso, R; Fantechi, R; Ferrante, I; Giassi, A; Gregorio, A; Ligabue, F; Lusiani, A; Marrocchesi, P S; Messineo, A; Palla, Fabrizio; Sanguinetti, G; Sciabà, A; Spagnolo, P; Steinberger, Jack; Tenchini, Roberto; Tonelli, G; Vannini, C; Venturi, A; Verdini, P G; Blair, G A; Bryant, L M; Chambers, J T; Gao, Y; Green, M G; Medcalf, T; Perrodo, P; Strong, J A; Von Wimmersperg-Töller, J H; Botterill, David R; Clifft, R W; Edgecock, T R; Haywood, S; Maley, P; Norton, P R; Thompson, J C; Wright, A E; Bloch-Devaux, B; Colas, P; Kozanecki, Witold; Lançon, E; Lemaire, M C; Locci, E; Pérez, P; Rander, J; Renardy, J F; Roussarie, A; Schuller, J P; Schwindling, J; Trabelsi, A; Vallage, B; Black, S N; Dann, J H; Kim, H Y; Litke, A M; McNeil, M A; Taylor, G; Booth, C N; Boswell, R; Brew, C A J; Cartwright, S L; Combley, F; Kelly, M S; Lehto, M H; Newton, W M; Reeve, J; Thompson, L F; Affholderbach, K; Böhrer, A; Brandt, S; Cowan, G D; Foss, J; Grupen, Claus; Saraiva, P; Smolik, L; Stephan, F; Apollonio, M; Bosisio, L; Della Marina, R; Giannini, G; Gobbo, B; Musolino, G; Pütz, J; Rothberg, J E; Wasserbaech, S R; Williams, R W; Armstrong, S R; Charles, E; Elmer, P; Ferguson, D P S; Gao, Y S; González, S; Greening, T C; Hayes, O J; Hu, H; Jin, S; McNamara, P A; Nachtman, J M; Nielsen, J; Orejudos, W; Pan, Y B; Saadi, Y; Scott, I J; Walsh, J; Wu Sau Lan; Wu, X; Yamartino, J M; Zobernig, G

    1997-01-01

    In June 1996, the LEP centre-of-mass energy was raised to 161 GeV. Pair production of W bosons in e+e- collisions was observed for the first time by the LEP experiments. An integrated luminosity of 11 pb-1 was recorded in the ALEPH detector, in which WW candidate events were observed. In 6 events both Ws decay leptonically. In 16 events, one W decays leptonically, the other into hadrons. In the channel where both Ws decay into hadrons, a signal was separated from the large background by means of several multi-variate analyses. The W pair cross-section is measured to be sigma_WW = 4.23 +-0.73 (stat.) +- 0.19 (syst.) pb From this cross-section, the W mass is derived within the framework of the Standard Model: MW = 80.14 +- 0.34 (stat.) +- 0.09 (syst.) +- 0.03 (LEP~energy) GeV/c2.

  14. The Oklo natural reactor: Cumulative fission yields and retentivity of the symmetric mass region fission products

    Science.gov (United States)

    De Laeter, J. R.; Rosman, K. J. R.; Smith, C. L.

    1980-10-01

    Solid source mass spectrometry has been used to determine the relative cumulative fission yields of five elements in three samples of uranium ore from reactor zones in the Oklo mine site. Eighteen fission chains covering the mass range from 105 ≤ A ≤ 130 have been measured for Pd, Ag, Cd, Sn and Te. These measurements have enabled a number of nuclear parameters to be calculated including the relative proportions of 235U, 238U and 239Pu involved in the fission process. The concentration of the five elements in the Oklo samples have also been measured using the stable isotope dilution technique. These values have then been compared to the estimates of the amount of these elements produced by fission under the conditions that are appropriate to the three samples. This procedure enables the retentivity of the elements in the reactor zones to be evaluated. Our work confirms the fact that Pd and Te are retained almost in their entirety in the samples, whereas the other three elements have been partially lost from the reactor site. Almost all the Cd fission products have been lost, and more than 50% of the Ag and Sn fission-produced material has been removed.

  15. Evidence for a Mass Dependent Forward-Backward Asymmetry in Top Quark Pair Production

    CERN Document Server

    Aaltonen, T.; Amerio, S.; Amidei, D.; Anastassov, A.; Annovi, A.; Antos, J.; Apollinari, G.; Appel, J.A.; Apresyan, A.; Arisawa, T.; Artikov, A.; Asaadi, J.; Ashmanskas, W.; Auerbach, B.; Aurisano, A.; Azfar, F.; Badgett, W.; Barbaro-Galtieri, A.; Barnes, V.E.; Barnett, B.A.; Barria, P.; Bartos, P.; Bauce, M.; Bauer, G.; Bedeschi, F.; Beecher, D.; Behari, S.; Bellettini, G.; Bellinger, J.; Benjamin, D.; Beretvas, A.; Bhatti, A.; Binkley, M.; Bisello, D.; Bizjak, I.; Bland, K.R.; Blumenfeld, B.; Bocci, A.; Bodek, A.; Bortoletto, D.; Boudreau, J.; Boveia, A.; Brau, B.; Brigliadori, L.; Brisuda, A.; Bromberg, C.; Brucken, E.; Bucciantonio, M.; Budagov, J.; Budd, H.S.; Budd, S.; Burkett, K.; Busetto, G.; Bussey, P.; Buzatu, A.; Calancha, C.; Camarda, S.; Campanelli, M.; Campbell, M.; Canelli, F.; Canepa, A.; Carls, B.; Carlsmith, D.; Carosi, R.; Carrillo, S.; Carron, S.; Casal, B.; Casarsa, M.; Castro, A.; Catastini, P.; Cauz, D.; Cavaliere, V.; Cavalli-Sforza, M.; Cerri, A.; Cerrito, L.; Chen, Y.C.; Chertok, M.; Chiarelli, G.; Chlachidze, G.; Chlebana, F.; Cho, K.; Chokheli, D.; Chou, J.P.; Chung, W.H.; Chung, Y.S.; Ciobanu, C.I.; Ciocci, M.A.; Clark, A.; Compostella, G.; Convery, M.E.; Conway, J.; Corbo, M.; Cordelli, M.; Cox, C.A.; Cox, D.J.; Crescioli, F.; Cuenca Almenar, C.; Cuevas, J.; Culbertson, R.; Dagenhart, D.; d'Ascenzo, N.; Datta, M.; de Barbaro, P.; De Cecco, S.; De Lorenzo, G.; Dell'Orso, M.; Deluca, C.; Demortier, L.; Deng, J.; Deninno, M.; Devoto, F.; d'Errico, M.; Di Canto, A.; Di Ruzza, B.; Dittmann, J.R.; D'Onofrio, M.; Donati, S.; Dong, P.; Dorigo, M.; Dorigo, T.; Ebina, K.; Elagin, A.; Eppig, A.; Erbacher, R.; Errede, D.; Errede, S.; Ershaidat, N.; Eusebi, R.; Fang, H.C.; Farrington, S.; Feindt, M.; Fernandez, J.P.; Ferrazza, C.; Field, R.; Flanagan, G.; Forrest, R.; Frank, M.J.; Franklin, M.; Freeman, J.C.; Funakoshi, Y.; Furic, I.; Gallinaro, M.; Galyardt, J.; Garcia, J.E.; Garfinkel, A.F.; Garosi, P.; Gerberich, H.; Gerchtein, E.; Giagu, S.; Giakoumopoulou, V.; Giannetti, P.; Gibson, K.; Ginsburg, C.M.; Giokaris, N.; Giromini, P.; Giunta, M.; Giurgiu, G.; Glagolev, V.; Glenzinski, D.; Gold, M.; Goldin, D.; Goldschmidt, N.; Golossanov, A.; Gomez, G.; Gomez-Ceballos, G.; Goncharov, M.; Gonzalez, O.; Gorelov, I.; Goshaw, A.T.; Goulianos, K.; Gresele, A.; Grinstein, S.; Grosso-Pilcher, C.; Group, R.C.; Guimaraes da Costa, J.; Gunay-Unalan, Z.; Haber, C.; Hahn, S.R.; Halkiadakis, E.; Hamaguchi, A.; Han, J.Y.; Happacher, F.; Hara, K.; Hare, D.; Hare, M.; Harr, R.F.; Hatakeyama, K.; Hays, C.; Heck, M.; Heinrich, J.; Herndon, M.; Hewamanage, S.; Hidas, D.; Hocker, A.; Hopkins, W.; Horn, D.; Hou, S.; Hughes, R.E.; Hurwitz, M.; Husemann, U.; Hussain, N.; Hussein, M.; Huston, J.; Introzzi, G.; Iori, M.; Ivanov, A.; James, E.; Jang, D.; Jayatilaka, B.; Jeon, E.J.; Jha, M.K.; Jindariani, S.; Johnson, W.; Jones, M.; Joo, K.K.; Jun, S.Y.; Junk, T.R.; Kamon, T.; Karchin, P.E.; Kato, Y.; Ketchum, W.; Keung, J.; Khotilovich, V.; Kilminster, B.; Kim, D.H.; Kim, H.S.; Kim, H.W.; Kim, J.E.; Kim, M.J.; Kim, S.B.; Kim, S.H.; Kim, Y.K.; Kimura, N.; Kirby, M.; Klimenko, S.; Kondo, K.; Kong, D.J.; Konigsberg, J.; Kotwal, A.V.; Kreps, M.; Kroll, J.; Krop, D.; Krumnack, N.; Kruse, M.; Krutelyov, V.; Kuhr, T.; Kurata, M.; Kwang, S.; Laasanen, A.T.; Lami, S.; Lammel, S.; Lancaster, M.; Lander, R.L.; Lannon, K.; Lath, A.; Latino, G.; Lazzizzera, I.; LeCompte, T.; Lee, E.; Lee, H.S.; Lee, J.S.; Lee, S.W.; Leo, S.; Leone, S.; Lewis, J.D.; Lin, C.J.; Linacre, J.; Lindgren, M.; Lipeles, E.; Lister, A.; Litvintsev, D.O.; Liu, C.; Liu, Q.; Liu, T.; Lockwitz, S.; Lockyer, N.S.; Loginov, A.; Lucchesi, D.; Lueck, J.; Lujan, P.; Lukens, P.; Lungu, G.; Lys, J.; Lysak, R.; Madrak, R.; Maeshima, K.; Makhoul, K.; Maksimovic, P.; Malik, S.; Manca, G.; Manousakis-Katsikakis, A.; Margaroli, F.; Marino, C.; Martinez, M.; Martinez-Ballarin, R.; Mastrandrea, P.; Mathis, M.; Mattson, M.E.; Mazzanti, P.; McFarland, K.S.; McIntyre, P.; McNulty, R.; Mehta, A.; Mehtala, P.; Menzione, A.; Mesropian, C.; Miao, T.; Mietlicki, D.; Mitra, A.; Miyake, H.; Moed, S.; Moggi, N.; Mondragon, M.N.; Moon, C.S.; Moore, R.; Morello, M.J.; Morlock, J.; Movilla Fernandez, P.; Mukherjee, A.; Muller, Th.; Murat, P.; Mussini, M.; Nachtman, J.; Nagai, Y.; Naganoma, J.; Nakano, I.; Napier, A.; Nett, J.; Neu, C.; Neubauer, M.S.; Nielsen, J.; Nodulman, L.; Norniella, O.; Nurse, E.; Oakes, L.; Oh, S.H.; Oh, Y.D.; Oksuzian, I.; Okusawa, T.; Orava, R.; Ortolan, L.; Griso, S.Pagan; Pagliarone, C.; Palencia, E.; Papadimitriou, V.; Paramonov, A.A.; Patrick, J.; Pauletta, G.; Paulini, M.; Paus, C.; Pellett, D.E.; Penzo, A.; Phillips, T.J.; Piacentino, G.; Pianori, E.; Pilot, J.; Pitts, K.; Plager, C.; Pondrom, L.; Potamianos, K.; Poukhov, O.; Prokoshin, F.; Pronko, A.; Ptohos, F.; Pueschel, E.; Punzi, G.; Pursley, J.; Rahaman, A.; Ramakrishnan, V.; Ranjan, N.; Redondo, I.; Renton, P.; Rescigno, M.; Rimondi, F.; Ristori, L.; Robson, A.; Rodrigo, T.; Rodriguez, T.; Rogers, E.; Rolli, S.; Roser, R.; Rossi, M.; Rubbo, F.; Ruffini, F.; Ruiz, A.; Russ, J.; Rusu, V.; Safonov, A.; Sakumoto, W.K.; Sakurai, Y.; Santi, L.; Sartori, L.; Sato, K.; Saveliev, V.; Savoy-Navarro, A.; Schlabach, P.; Schmidt, A.; Schmidt, E.E.; Schmidt, M.P.; Schmitt, M.; Schwarz, T.; Scodellaro, L.; Scribano, A.; Scuri, F.; Sedov, A.; Seidel, S.; Seiya, Y.; Semenov, A.; Sforza, F.; Sfyrla, A.; Shalhout, S.Z.; Shears, T.; Shepard, P.F.; Shimojima, M.; Shiraishi, S.; Shochet, M.; Shreyber, I.; Simonenko, A.; Sinervo, P.; Sissakian, A.; Sliwa, K.; Smith, J.R.; Snider, F.D.; Soha, A.; Somalwar, S.; Sorin, V.; Squillacioti, P.; Stancari, M.; Stanitzki, M.; Denis, R.St.; Stelzer, B.; Stelzer-Chilton, O.; Stentz, D.; Strologas, J.; Strycker, G.L.; Sudo, Y.; Sukhanov, A.; Suslov, I.; Takemasa, K.; Takeuchi, Y.; Tang, J.; Tecchio, M.; Teng, P.K.; Thom, J.; Thome, J.; Thompson, G.A.; Thomson, E.; Ttito-Guzman, P.; Tkaczyk, S.; Toback, D.; Tokar, S.; Tollefson, K.; Tomura, T.; Tonelli, D.; Torre, S.; Torretta, D.; Totaro, P.; Trovato, M.; Tu, Y.; Ukegawa, F.; Uozumi, S.; Varganov, A.; Vazquez, F.; Velev, G.; Vellidis, C.; Vidal, M.; Vila, I.; Vilar, R.; Vogel, M.; Volpi, G.; Wagner, P.; Wagner, R.L.; Wakisaka, T.; Wallny, R.; Wang, S.M.; Warburton, A.; Waters, D.; Weinberger, M.; Wester, W.C., III; Whitehouse, B.; Whiteson, D.; Wicklund, A.B.; Wicklund, E.; Wilbur, S.; Wick, F.; Williams, H.H.; Wilson, J.S.; Wilson, P.; Winer, B.L.; Wittich, P.; Wolbers, S.; Wolfe, H.; Wright, T.; Wu, X.; Wu, Z.; Yamamoto, K.; Yamaoka, J.; Yang, T.; Yang, U.K.; Yang, Y.C.; Yao, W.M.; Yeh, G.P.; Yi, K.; Yoh, J.; Yorita, K.; Yoshida, T.; Yu, G.B.; Yu, I.; Yu, S.S.; Yun, J.C.; Zanetti, A.; Zeng, Y.; Zucchelli, S.

    2011-01-01

    We present a new measurement of the inclusive forward-backward t-tbar production asymmetry and its rapidity and mass dependence. The measurements are performed with 5.3 fb^{-1} of p-pbar collisions at \\sqrt{s} = 1.96 TeV, recorded with CDF II at the Fermilab Tevatron. Significant inclusive asymmetries are observed in the laboratory and t-tbar rest frame, and are consistent with CP conservation under interchange of t and tbar. In the t-tbar rest frame, the asymmetry increases with the t-tbar rapidity difference, \\Delta(y), and with the invariant mass M_{t-tbar} of the t-tbar system. Parton-level asymmetries are derived in two regions of each variable, and the asymmetry is found to be most significant at large \\Delta(y) and M_{t-tbar}. For M_{t-tbar} > 450 GeV/c^2, the parton-level asymmetry in the t-tbar rest frame is A^{t-tbar} = 0.475\\pm 0.114 compared to a next-to-leading order QCD prediction of 0.088\\pm 0.013.

  16. Daily cortisol production rate in man determined by stable isotope dilution/mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Esteban, N.V.; Loughlin, T.; Yergey, A.L.; Zawadzki, J.K.; Booth, J.D.; Winterer, J.C.; Loriaux, D.L. (National Institute of Child Health and Human Development, Bethesda, MD (USA))

    1991-01-01

    Growth retardation as well as the development of Cushingoid features in adrenally insufficient patients treated with the currently accepted replacement dose of cortisol (33-41 mumol/day.m2; 12-15 mg/m2.day) prompted us to reevaluate the cortisol production rate (FPR) in normal subjects and patients with Cushing's syndrome, using a recently developed thermospray liquid chromatography-mass spectrometry method. The stable isotope (9,12,12-2H3)cortisol was infused continuously for 31 h at about 5% of the anticipated FPR. Blood samples were obtained at 20-min intervals for 24 h, spun, and pooled in 4-h groups. Tracer dilution in plasma was determined by liquid chromatography/mass spectrometry. The method was validated with controlled infusions in 6 patients with adrenal insufficiency. Results from 12 normal volunteers revealed a FPR of 27.3 +/- 7.5 mumol/day (9.9 +/- 2.7 mg/day) or 15.7 mumol/day.m2; 5.7 mg/m2. day. A previously unreported circadian variation in FPR was observed. Patients with Cushing's syndrome demonstrated unequivocal elevation of FPR and cortisol concentration correlated during each sample period in normal volunteers, indicating that cortisol secretion, rather than metabolism, is mainly responsible for changes in plasma cortisol. Our data suggest that the FPR in normal subjects may be lower than previously believed.

  17. Resistive thrust production can be as crucial as added mass mechanisms for inertial undulatory swimmers.

    Science.gov (United States)

    Piñeirua, M; Godoy-Diana, R; Thiria, B

    2015-08-01

    In this Rapid Communication, we address a crucial point regarding the description of moderate to high Reynolds numbers aquatic swimmers. For decades, swimming animals have been classified in two different families of propulsive mechanisms based on the Reynolds number: the resistive swimmers, using local friction to produce the necessary thrust force for locomotion at low Reynolds number, and the reactive swimmers, lying in the high Reynolds range, and using added mass acceleration (described by perfect fluid theory). However, inertial swimmers are also systems that dissipate energy, due to their finite size, therefore involving strong resistive contributions, even for high Reynolds numbers. Using a complete model for the hydrodynamic forces, involving both reactive and resistive contributions, we revisit here the physical mechanisms responsible for the thrust production of such swimmers. We show, for instance, that the resistive part of the force balance is as crucial as added mass effects in the modeling of the thrust force, especially for elongated species. The conclusions brought by this work may have significant contributions to the understanding of complex swimming mechanisms, especially for the future design of artificial swimmers.

  18. Seesaw Majoron Model of Neutrino Mass and Novel Signals in Higgs Boson Production at LEP

    CERN Document Server

    Díaz, M A; Restrepo, D A; Valle, José W F; Diaz, Marco A.; Restrepo, Diego A.

    1998-01-01

    We perform a careful study of the neutral scalar sector of a model which includes a singlet, a doublet, and a triplet scalar field under $SU(2)$. This model is motivated by neutrino physics, since it is simply the most general version of the seesaw model of neutrino mass generation through spontaneous violation of lepton number. The neutral Higgs sector contains three CP-even and one massive CP-odd Higgs boson $A$, in addition to the massless CP-odd majoron $J$. The weakly interacting majoron remains massless if the breaking of lepton number symmetry is purely spontaneous. We show that the massive CP-odd Higgs boson may invisibly decay to three majorons, as well as to a CP-even Higgs $H$ boson plus a majoron. We consider the associated Higgs production $e^+e^- \\to Z corresponding limits on masses and coupling that follow from LEP I precision measurements of the invisible Z width. We also study a novel $b \\bar{b} perform a Monte-Carlo simulation of the signal in order to illustrate the limits on Higgs boson ma...

  19. CALiPER Summary of Results. Round 13 of Product Testing

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2011-10-01

    The Department of Energy (DOE) Commercially Available Light-Emitting Diode (LED) Product Evaluation and Reporting (CALiPER) Program has been purchasing and testing general illumination solid-state lighting (SSL) products since 2006.

  20. Exploiting multiple mahalanobis distance metrics to screen outliers from analog product manufacturing test responses

    NARCIS (Netherlands)

    Krishnan, S.; Kerkhoff, H.G.

    2013-01-01

    Stringent quality requirements on final electronic products are continuously forcing semiconductor industries, especially the automobile industry, to insert additional reliability tests in their production flow. The problem with linear regressions models for outlier identification in analog and RF

  1. Automated CD-SEM recipe creation technology for mass production using CAD data

    Science.gov (United States)

    Kawahara, Toshikazu; Yoshida, Masamichi; Tanaka, Masashi; Ido, Sanyu; Nakano, Hiroyuki; Adachi, Naokaka; Abe, Yuichi; Nagatomo, Wataru

    2011-03-01

    Critical Dimension Scanning Electron Microscope (CD-SEM) recipe creation needs sample preparation necessary for matching pattern registration, and recipe creation on CD-SEM using the sample, which hinders the reduction in test production cost and time in semiconductor manufacturing factories. From the perspective of cost reduction and improvement of the test production efficiency, automated CD-SEM recipe creation without the sample preparation and the manual operation has been important in the production lines. For the automated CD-SEM recipe creation, we have introduced RecipeDirector (RD) that enables the recipe creation by using Computer-Aided Design (CAD) data and text data that includes measurement information. We have developed a system that automatically creates the CAD data and the text data necessary for the recipe creation on RD; and, for the elimination of the manual operation, we have enhanced RD so that all measurement information can be specified in the text data. As a result, we have established an automated CD-SEM recipe creation system without the sample preparation and the manual operation. For the introduction of the CD-SEM recipe creation system using RD to the production lines, the accuracy of the pattern matching was an issue. The shape of design templates for the matching created from the CAD data was different from that of SEM images in vision. Thus, a development of robust pattern matching algorithm that considers the shape difference was needed. The addition of image processing of the templates for the matching and shape processing of the CAD patterns in the lower layer has enabled the robust pattern matching. This paper describes the automated CD-SEM recipe creation technology for the production lines without the sample preparation and the manual operation using RD applied in Sony Semiconductor Kyusyu Corporation Kumamoto Technology Center (SCK Corporation Kumamoto TEC).

  2. Resummation and matching of b-quark mass effects in b anti bH production

    Energy Technology Data Exchange (ETDEWEB)

    Bonvini, Marco [Oxford Univ. (United Kingdom). Rudolf Peierls Center for Theoretical Physics; Papanastasiou, Andrew S.; Tackmann, Frank J. [DESY Hamburg (Germany). Theory Group

    2015-11-15

    We use a systematic effective field theory setup to derive the b anti bH production cross section. Our result combines the merits of both fixed 4-flavor and 5-flavor schemes. It contains the full 4-flavor result, including the exact dependence on the b-quark mass, and improves it with a resummation of collinear logarithms of m{sub b}/m{sub H}. In the massless limit, it corresponds to a reorganized 5-flavor result. While we focus on b anti bH production, our method applies to generic heavy-quark initiated processes at hadron colliders. Our setup resembles the variable flavor number schemes known from heavy-flavor production in deep-inelastic scattering, but also differs in some key aspects. Most importantly, the effective b-quark PDF appears as part of the perturbative expansion of the final result where it effectively counts as an O(α{sub s}) object. The transition between the fixed-order (4-flavor) and resummation (5-flavor) regimes is governed by the low matching scale at which the b-quark is integrated out. Varying this scale provides a systematic way to assess the perturbative uncertainties associated with the resummation and matching procedure and reduces by going to higher orders. We discuss the practical implementation and present numerical results for the b anti bH production cross section at NLO+NLL. We also provide a comparison to the corresponding predictions in the fixed 4-flavor and 5-flavor results and the Santander matching prescription. Compared to the latter, we find a slightly reduced uncertainty and a larger central value, with its central value lying at the lower edge of our uncertainty band.

  3. Improved approaches to ecotoxicity testing of petroleum products

    Energy Technology Data Exchange (ETDEWEB)

    Tsvetnenko, Y.; Evans, L. [Curtin University of Technology, Perth (Australia)

    2002-09-01

    Crude oils produced in the North West shelf of Western Australia are highly volatile, a characteristic not shared by most of the Northern Hemisphere crude oils on which internationally accepted toxicity test protocols were developed. Because of this volatility and some other factors, the LC50 and EC50 values obtained from acute toxicity tests will be significantly affected by the changes of toxicant concentration in test solutions during the period of exposure. To address these issues all steps of a standard protocol for crude oil toxicity testing have been revised. A systematic study has been performed on factors which affect petroleum hydrocarbon solubilisation in aqueous systems during test solution preparations. The influence of mixing time, agitation energy and volume/interface ratio on a hydrocarbon concentration in a water-soluble fraction (WSF) was studied for heavy, medium and light crude oils. A study of the sensitivity of marine unicellular algae to WSF of crude oils was conducted with Isochrysis sp., Nannochloropsis-like sp. and Nitzchia closterium. Total concentrations of hydrocarbons dissolved in test solutions were estimated by UV-spectrometry and GC/FID chemical analyses. When the toxicant concentration decreased during the exposure period, the EC50 values derived from initial or final concentrations either underestimate or overestimate toxicity, respectively. Therefore, weighted average concentrations (WAC) calculated for the whole test period were recommended for expressing hydrocarbon concentrations in test solutions of crude oils. Toxicity indices calculated from WAC of total hydrocarbons for different crude oils can be compared regardless of the rates of hydrocarbon loss. (author)

  4. Angular Distributions of High-Mass Dilepton Production in Hadron Collisions

    Energy Technology Data Exchange (ETDEWEB)

    McClellan, Randall Evan [Illinois U., Urbana

    2016-01-01

    The SeaQuest experiment is a fixed-target dimuon experiment currently running at the Fermi National Accelerator Laboratory (FNAL). By utilizing the high-intensity, 120 GeV proton beam delivered by the FNAL Main Injector (MI), SeaQuest is able to measure proton-induced Drell-Yan dimuon production off of various nuclear targets in kinematic regions inaccessible to previous similar experiments. A suitably large fraction of the final dataset has been recorded, reconstructed, and analyzed. Very preliminary results from light-sea flavor asymmetry, nuclear dependence, and partonic energy loss analyses have been presented at numerous international conferences. A novel, FPGA-based trigger system has been designed, implemented, and optimized for the SeaQuest experiment. By implementing the trigger decision logic in FPGA firmware, it is more adaptable to changing experimental conditions. Additionally, the peripheral tasks of timing alignment, “trigger matrix” generation, and firmware uploading have been mostly automated, reducing the likelihood of user error in the maintenance and operation of the trigger system. Significant upgrades to hardware and firmware have greatly improved the performance of the trigger system since the 2012 commissioning run of SeaQuest. Four additional v1495 modules were added to facilitate thorough pulser testing of the firmware designs and in-situ pulser tests of all compiled firmware. These pulser tests proved crucial for diagnosing many errors that may have otherwise gone unnoticed. A significant change to the internal clocking of the trigger system eliminated a subtle source of rate-dependent trigger efficiency. With this upgrade, the trigger finally meets the “dead-time free” design specification. Drell-Yan dimuon data have been collected and analyzed for central θCS , with nearly flat acceptance in φCS , in the mass range 5.0 GeV < Mγ* < 10.0 GeV at forward xF with the SeaQuest spectrometer at FNAL. A very preliminary extraction of

  5. Angular Distributions of High-Mass Dilepton Production in Hadron Collisions

    Energy Technology Data Exchange (ETDEWEB)

    McClellan, Randall Evan [Illinois U., Urbana

    2016-01-01

    The SeaQuest experiment is a fixed-target dimuon experiment currently running at the Fermi National Accelerator Laboratory (FNAL). By utilizing the high-intensity, 120 GeV proton beam delivered by the FNAL Main Injector (MI), SeaQuest is able to measure proton-induced Drell-Yan dimuon production off of various nuclear targets in kinematic regions inaccessible to previous similar experiments. A suitably large fraction of the final dataset has been recorded, reconstructed, and analyzed. Very preliminary results from light-sea flavor asymmetry, nuclear dependence, and partonic energy loss analyses have been presented at numerous international conferences. A novel, FPGA-based trigger system has been designed, implemented, and optimized for the SeaQuest experiment. By implementing the trigger decision logic in FPGA firmware, it is more adaptable to changing experimental conditions. Additionally, the peripheral tasks of timing alignment, “trigger matrix” generation, and firmware uploading have been mostly automated, reducing the likelihood of user error in the maintenance and operation of the trigger system. Significant upgrades to hardware and firmware have greatly improved the performance of the trigger system since the 2012 commissioning run of SeaQuest. Four additional v1495 modules were added to facilitate thorough pulser testing of the firmware designs and in-situ pulser tests of all compiled firmware. These pulser tests proved crucial for diagnosing many errors that may have otherwise gone unnoticed. A significant change to the internal clocking of the trigger system eliminated a subtle source of rate-dependent trigger efficiency. With this upgrade, the trigger finally meets the “dead-time free” design specification. Drell-Yan dimuon data have been collected and analyzed for central θCS , with nearly flat acceptance in φCS , in the mass range 5.0 GeV < Mγ* < 10.0 GeV at forward xF with the SeaQuest spectrometer at FNAL. A very preliminary extraction of

  6. Application of Liquid Chromatography/Ion Trap Mass Spectrometry Technique to Determine Ergot Alkaloids in Grain Products

    Directory of Open Access Journals (Sweden)

    Krystyna Szymczyk

    2015-01-01

    Full Text Available A liquid chromatography/ion trap mass spectrometry-based method to determine six ergot alkaloids and their isomers is presented. The samples were cleaned on neutral alumina-based solid-phase extraction cartridges. The following method parameters were obtained (depending on the analyte and spiking level: method recovery from 63.0 to 104.6 %, relative standard deviation below 18 %, linear range from 1 to 325 μg/kg, linear correlation coefficient not less than 0.98. The developed analytical procedure was applied to determine the levels of ergot alkaloids in 65 samples of selected rye-based food products (flour– 34 samples, bran – 12 samples, rye – 18 samples, flakes – 1 sample. Measurable levels of alkaloids were found in majority of the analysed samples, particularly in rye flour. Additionally, alkaloids were determined in ergot sclerotia isolated from rye grains. Total content was nearly 0.01 % (97.9 mg/kg. However, the alkaloid profi le was dominated by ergocristine at 45.6 % (44.7 mg/kg, an alkaloid not commonly found in the tested food products. Ergocorninine at 0.2 % (0.2 mg/kg was the least abundant alkaloid.

  7. Biomimetic oxidation studies of monensin A catalyzed by metalloporphyrins: identification of hydroxyl derivative product by electrospray tandem mass spectrometry

    Directory of Open Access Journals (Sweden)

    José N. Sousa-Junior

    2013-08-01

    Full Text Available Monensin A is an important commercially available natural product isolated from Streptomyces cinnamonensins that shows antibiotic and anti-parasitic activities. This molecule has a significant influence in the antibiotic market, but until now there are no studies on putative metabolite formations. Bioorganic catalysts applying metalloporphyrins and mono-oxygen donors are able to mimic the cytochrome P450 reactions. This model has been employed for natural product metabolism studies affording several new putative metabolites and in vivo experiments confirming the relevance of this procedure. In this work we evaluated the potential of 10,15,20-tetrakis (pentafluorophenyl porphyrin metal(III chloride [Fe(TFPPCl] catalyst models to afford a putative monensin A metabolite. Oxidation agents such as meta-chloroperoxy benzoic acid, iodosylbenzene, hydrogen peroxide 30 wt.% and tert-butyl hydroperoxide 70 wt.%, were used to investigate different reaction conditions, in addition to the analysis of the influence of the solvent. The quantification of total monensin A conversion and the structure of the new hydroxylated putative metabolite were proposed based on electrospray ionization tandem mass spectrometry analysis. The porphyrin tested, afforded moderate conversions of monensin A in all reaction conditions and the selectivity was found to be dependent on the oxidation/medium employed.

  8. Power System Mass Analysis for Hydrogen Reduction Oxygen Production on the Lunar Surface

    Science.gov (United States)

    Colozza, Anthony J.

    2009-01-01

    The production of oxygen from the lunar regolith requires both thermal and electrical power in roughly similar proportions. This unique power requirement is unlike most applications on the lunar surface. To efficiently meet these requirements, both solar PV array and solar concentrator systems were evaluated. The mass of various types of photovoltaic and concentrator based systems were calculated to determine the type of power system that provided the highest specific power. These were compared over a range of oxygen production rates. Also a hybrid type power system was also considered. This system utilized a photovoltaic array to produce the electrical power and a concentrator to provide the thermal power. For a single source system the three systems with the highest specific power were a flexible concentrator/Stirling engine system, a rigid concentrator/Stirling engine system and a tracking triple junction solar array system. These systems had specific power values of 43, 34, and 33 W/kg, respectively. The hybrid power system provided much higher specific power values then the single source systems. The best hybrid combinations were the triple junction solar array with the flexible concentrator and the rigid concentrator. These systems had a specific power of 81 and 68 W/kg, respectively.

  9. Agent Behavior-Based Simulation Study on Mass Collaborative Product Development Process

    Directory of Open Access Journals (Sweden)

    Shuo Zhang

    2015-01-01

    Full Text Available Mass collaborative product development (MCPD benefits people by high innovation products with lower cost and shorter lead time due to quick development of group innovation, Internet-based customization, and prototype manufacturing. Simulation is an effective way to study the evolution process and therefore to guarantee the success of MCPD. In this paper, an agent behavior-based simulation approach of MCPD is developed, which models the MCPD process as the interactive process of design agents and the environment objects based on Complex Adaptive System (CAS theory. Next, the structure model of design agent is proposed, and the modification and collaboration behaviors are described. Third, the agent behavior-based simulation flow of MCPD is designed. At last, simulation experiments are carried out based on an engineering case of mobile phone design. The experiment results show the following: (1 the community scale has significant influence on MCPD process; (2 the simulation process can explicitly represent the modification and collaboration behaviors of design agents; (3 the community evolution process can be observed and analyzed dynamically based on simulation data.

  10. Physics of High-Mass Dimuon Production at the 50-GeV Proton Synchrotron

    CERN Document Server

    Peng, J C; Moss, J M; Sawada, S; Chiba, J

    2000-01-01

    We discuss the physics interest and the experimental feasibility for detecting high-mass dimuon pairs using the planned 50-GeV Proton Synchrotron (PS) at the KEK/JHF and JAERI/NSP joint accelerator project. The Drell-Yan measurement of $p+d$ versus $p+p$ at 50 GeV will provide unique information on the flavor asymmetry of proton's up and down sea-quark distributions in the large-$x$ region. A study of the nuclear dependences of Drell-Yan cross sections can reveal the modification of antiquark distributions in nuclei. Furthermore, the effect of energy loss for fast partons traversing nuclear medium could also be sensitively measured. If polarized proton beam becomes available at the 50-GeV PS, unique information on the sea-quark polarization could be obtained. Study of heavy quarkonium production at the 50-GeV PS can set important constraints on the mechanism of vector meson productions. Using a prototype dimuon spectrometer, we have simulated the sensitivities for a variety of measurements.

  11. Mass transport around comets and its impact on the seasonal differences in water production rates

    Energy Technology Data Exchange (ETDEWEB)

    Rubin, M.; Altwegg, K.; Thomas, N. [Physikalisches Institut, University of Bern, Sidlerstrasse 5, 3012 Bern (Switzerland); Fougere, N.; Combi, M. R.; Tenishev, V. M. [Atmospheric, Oceanic and Space Sciences, University of Michigan, 2455 Hayward Street, Ann Arbor, MI 48109 (United States); Le Roy, L. [Center for Space and Habitability, University of Bern, Sidlerstrasse 5, 3012 Bern (Switzerland)

    2014-06-20

    Comets are surrounded by a thin expanding atmosphere, and although the nucleus' gravity is small, some molecules and grains, possibly with the inclusion of ices, can get transported around the nucleus through scattering (atoms/molecules) and gravitational pull (grains). Based on the obliquity of the comet, it is also possible that volatile material and icy grains get trapped in regions, which are in shadow until the comet passes its equinox. When the Sun rises above the horizon and the surface starts to heat up, this condensed material starts to desorb and icy grains will sublimate off the surface, possibly increasing the comet's neutral gas production rate on the outbound path. In this paper we investigate the mass transport around the nucleus, and based on a simplified model, we derive the possible contribution to the asymmetry in the seasonal gas production rate that could arise from trapped material released from cold areas once they come into sunlight. We conclude that the total amount of volatiles retained by this effect can only contribute up to a few percent of the asymmetry observed in some comets.

  12. Non-equilibrium quantum plasmas in scalar QED photon production, magnetic and Debye masses and conductivity

    CERN Document Server

    Boyanovsky, D; Simionato, M

    2000-01-01

    We study the generation of a non-equilibrium plasma in scalar QED with N charged scalar fields through spinodal instabilities in the case of a super cooled second order phase transition and parametric amplification when the order parameter oscillates with large amplitude around the minimum of the potential.The focus is to study the non-equilibrium electromagnetic properties of the plasma, such as photon production, electric and magnetic screening and conductivity. A novel kinetic equation is introduced to compute photon production far away from equilibrium in the large N limit and lowest order in the electromagnetic coupling.During the early stages of the dynamics the photon density grows exponentially and asymptotically the amplitude and frequency distribution becomes \\sim alpha m^2/[lambda^2 ømega^3] with lambda the scalar self-coupling and m the scalar mass.In the case of a phase transition,electric and magnetic fields are correlated on distances xi(t) \\sim sqrt{t} during the early stages and the power sp...

  13. Evolution of stellar collision products in open clusters. II. A grid of low-mass collisions

    CERN Document Server

    Glebbeek, E

    2008-01-01

    In a companion paper we studied the detailed evolution of stellar collision products that occurred in an $N$-body simulation of the old open cluster M67 and compared our detailed models to simple prescriptions. In this paper we extend this work by studying the evolution of the collision products in open clusters as a function of mass and age of the progenitor stars. We calculated a grid of head-on collisions covering the section of parameter space relevant for collisions in open clusters. We create detailed models of the merger remnants using an entropy-sorting algorithm and follow their subsequent evolution during the initial contraction phase, through the main sequence and up to the giant branch with our detailed stellar evolution code. We compare the location of our models in a colour-magnitude diagram to the observed blue straggler population of the old open clusters M67 and NGC 188 and find that they cover the observed blue straggler region of both clusters. For M67, collisions need to have taken place r...

  14. Recommendation for a test battery for the ecotoxicological evaluation of the environmental safety of construction products.

    Science.gov (United States)

    Gartiser, Stefan; Heisterkamp, Ines; Schoknecht, Ute; Bandow, Nicole; Burkhardt, N Michael; Ratte, Monika; Ilvonen, Outi

    2017-03-01

    The European Construction Products Regulation allows Member States to adopt rules for evaluating the environmental impact of their buildings. The aim of the project was to develop recommendations for a test battery for the ecotoxicological assessment of the environmental impact of construction products for outdoor use and contribute to the European harmonization of test methods. From a shortlist of 39 products 20 products were included in the ecotoxicological testing program. Monolithic and plate-like construction products were eluted in the Dynamic Surface Leaching test (DSLT) in accordance with CEN/TS 16637-2, granular products were eluted in a one stage batch test in accordance with DIN EN 12457-1. The eluates were examined in four aquatic toxicity tests (algae, daphnia, luminescent bacteria, fish eggs), a genotoxicity test (umu test) and in the respirometer test (OECD 301 F). Here, low to very high ecotoxicity was observed (up to a dilution factor of 1536). Six out of 8 eluates, whose TOC exceeded 10 mg L(-1) showed a good biodegradability above 75%. The intra-laboratory repeatability of the Lowest Ineffective Dilution (LID) usually was within ±1 dilution steps (ecotoxicity tests) and ±2 dilution steps (leaching and ecotoxicity tests). This is acceptable, when considering that the overall variability of sample preparation, leaching test, and bioassays add up. The conclusions lead to practical recommendations for a suitable combination of leaching and ecotoxicity tests.

  15. Study of test-mass charging process in the LISA missions due to diffuse γ-rays

    Science.gov (United States)

    Finetti, N.; Scrimaglio, R.; Grimani, C.; Fabi, M.

    2009-03-01

    Gravitational inertial sensors will be placed on board the Laser Interferometer Space Antenna (LISA) and aboard its precursor mission LISA Pathfinder (LISA-PF) in order to detect low frequency gravitational waves in space. Free-floating test-masses (Au7Pt3 cubes) will be housed in inertial sensors for detecting possible laser signal variations induced by gravitational waves. Charging of the LISA test-masses due to exposure of the spacecraft to cosmic radiation and energetic solar particles will affect operation of gravitational inertial sensors. In this paper we report on the role of diffuse γ-rays in charging the LISA and LISA-PF test-masses with respect to protons and helium nuclei. The diffuse γ-ray flux in the Galaxy has been interpolated taking into account the outcomes of recent calculations. A comparison with γ-ray observations gathered by different experiments (COMPTEL and EGRET, Milagro, Whipple, HEGRA, TIBET) has been carried out. Simulations of the test-mass charging process have been performed by means of the FLUKA2006.3b package. Monte Carlo simulations of the interaction of cosmic particles with the LISA spacecraft indicate that the diffuse γ-ray contribution to the average steady-state test-mass charging rate and to the single-sided power spectrum of the charge rate noise is marginal with respect to that due to galactic cosmic-rays.

  16. Study of test-mass charging process in the LISA missions due to diffuse gamma-rays

    Energy Technology Data Exchange (ETDEWEB)

    Finetti, N; Scrimaglio, R [Dipartimento di Fisica dell' Universita degli Studi dell' Aquila and Gruppo INFN dell' Aquila collegato ai Laboratori Nazionali del Gran Sasso, Via Vetoio, 67010 Coppito, L' Aquila (Italy); Grimani, C; Fabi, M, E-mail: noemi.finetti@aquila.infn.i [Istituto di Fisica dell' Universita degli Studi di Urbino ' Carlo Bo' , Via S. Chiara, 27, 61029, Urbino (Italy)

    2009-03-01

    Gravitational inertial sensors will be placed on board the Laser Interferometer Space Antenna (LISA) and aboard its precursor mission LISA Pathfinder (LISA-PF) in order to detect low frequency gravitational waves in space. Free-floating test-masses (Au{sub 7}Pt{sub 3} cubes) will be housed in inertial sensors for detecting possible laser signal variations induced by gravitational waves. Charging of the LISA test-masses due to exposure of the spacecraft to cosmic radiation and energetic solar particles will affect operation of gravitational inertial sensors. In this paper we report on the role of diffuse gamma-rays in charging the LISA and LISA-PF test-masses with respect to protons and helium nuclei. The diffuse gamma-ray flux in the Galaxy has been interpolated taking into account the outcomes of recent calculations. A comparison with gamma-ray observations gathered by different experiments (COMPTEL and EGRET, Milagro, Whipple, HEGRA, TIBET) has been carried out. Simulations of the test-mass charging process have been performed by means of the FLUKA2006.3b package. Monte Carlo simulations of the interaction of cosmic particles with the LISA spacecraft indicate that the diffuse gamma-ray contribution to the average steady-state test-mass charging rate and to the single-sided power spectrum of the charge rate noise is marginal with respect to that due to galactic cosmic-rays.

  17. Facility for generating crew waste water product for ECLSS testing

    Science.gov (United States)

    Buitekant, Alan; Roberts, Barry C.

    1990-01-01

    An End-use Equipment Facility (EEF) has been constructed which is used to simulate water interfaces between the Space Station Freedom Environmental Control and Life Support Systems (ECLSS) and man systems. The EEF is used to generate waste water to be treated by ECLSS water recovery systems. The EEF will also be used to close the water recovery loop by allowing test subjects to use recovered hygiene and potable water during several phases of testing. This paper describes the design and basic operation of the EEF.

  18. Facility for generating crew waste water product for ECLSS testing

    Science.gov (United States)

    Buitekant, Alan; Roberts, Barry C.

    1990-01-01

    An End-use Equipment Facility (EEF) has been constructed which is used to simulate water interfaces between the Space Station Freedom Environmental Control and Life Support Systems (ECLSS) and man systems. The EEF is used to generate waste water to be treated by ECLSS water recovery systems. The EEF will also be used to close the water recovery loop by allowing test subjects to use recovered hygiene and potable water during several phases of testing. This paper describes the design and basic operation of the EEF.

  19. Determination of melamine in milk-based products and other food and beverage products by ion-pair liquid chromatography-tandem mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Ibanez, Maria; Sancho, Juan V. [Research Institute for Pesticides and Water, University Jaume I, E-12071, Castellon (Spain); Hernandez, Felix, E-mail: felix.hernandez@qfa.uji.es [Research Institute for Pesticides and Water, University Jaume I, E-12071, Castellon (Spain)

    2009-09-01

    This paper describes a fast method for the sensitive and selective determination of melamine in a wide range of food matrices, including several milk-based products. The method involves an extraction with aqueous 1% trichloroacetic acid before the injection of the 10-fold diluted extract into the liquid chromatography-electrospray tandem mass spectrometry (LC-ESI-MS/MS) system, using labelled melamine as the internal standard. As melamine is present in aqueous media in the cationic form, the chromatographic separation in reversed-phase LC requires the use of anionic ion-pair reagents, such as tridecafluoroheptanoic acid (THFA). This allows a satisfactory chromatographic retention and peak shape in all the types of food samples investigated. The method has been validated in six food matrices (biscuit, dry pasta and four milk-based products) by means of recovery experiments in samples spiked at 1 and 5 mg kg{sup -1}. Average recoveries (n = 5) ranged from 77% to 100%, with excellent precision (RSDs lower than 5%) and limits of detection between 0.01 and 0.1 mg kg{sup -1}. In addition, accuracy and robustness of the method was proven in different soya-based matrices by means of quality control (QC) sample analysis. QC recoveries, at 1 and 2.5 mg kg{sup -1}, were satisfactory, ranging from 79% to 110%. The method developed in this work has been applied to the determination of melamine in different types of food samples. All detections were confirmed by acquiring two MS/MS transitions (127 > 85 for quantification; 127 > 68 for confirmation) and comparing their ion intensity ratio with that of reference standards. Accuracy of the method was also assessed by applying it to a milk-based product and a baking mix material as part of an EU proficiency test, in which highly satisfactory results were obtained.

  20. 46 CFR 160.077-23 - Production tests and inspections.

    Science.gov (United States)

    2010-10-01

    ... MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Hybrid Inflatable Personal Flotation Devices... work is done on hybrid PFD's or component materials, and where completed PFD's are stored; and (vii... specified tolerance for the torque values of the fasteners. (x) Inflation chamber materials test equipment...

  1. An interactive style of the testing database production for EIS

    Directory of Open Access Journals (Sweden)

    Milan Mišovič

    2006-01-01

    Full Text Available Using a progressive Information Technology for development of Software Modules for Enterprise Information Systems brings a lot of practical and theoretical problems. One of them is a verification of results achieved in Life Cycle Stages, especially in the analysis stage. Instead of a very deep theoretical approach we can use quite practical testing by means of a testing database. Such testing database has to be constructed gradually from the Data Flow Diagram by a special algorithm.This article introduces a formal description of the entity population and entity states. There is suggested to deal with fragments of the DFD that are produced with respect to the event set. This DFD event fragment is refined to transactions and their elementary functions. There is defined a transaction path in every transaction. By means of a special state equation system is generally defined conception of a correct functional processing of entities going along a selected transaction path. Solutions of such state equation systems are platform for getting a testing database.

  2. Measurement of the jet mass distribution in boosted $\\mathrm{t}\\bar{\\mathrm{t}}$ production at $\\sqrt{s}=8~\\mathrm{TeV}$

    CERN Document Server

    CMS Collaboration

    2016-01-01

    A first measurement is performed of the differential $\\mathrm{t}\\bar{\\mathrm{t}}$ production cross section as a function of the leading jet mass in fully-merged top quark decays. Data collected with the CMS detector in pp collisions at $\\sqrt{s}=8$ TeV are used, corresponding to an integrated luminosity of 19.7 fb$^{-1}$. The measurement is carried out in the $\\ell$+jets channel, where the products of the leptonic decay are used to select $\\mathrm{t}\\bar{\\mathrm{t}}$ events with high Lorentz boosts. The products of the hadronic decay are reconstructed with a single Cambridge/Aachen jet with distance parameter $R=1.2$, and transverse momentum $p_{\\mathrm{T}}>400$ GeV. The cross section, as a function of the jet mass $m_{\\rm{jet}}$, is unfolded and reported on particle level. The measurement is used to test the modelling of boosted top quark production. The peak position of the $m_{\\rm{jet}}$ distribution is sensitive to the top quark mass $m_\\text{t}$ and the data are used to extract a value of $m_\\text{t}$ to...

  3. Relation between heart rate recovery after exercise testing and body mass index.

    Science.gov (United States)

    Barbosa Lins, Tereza Cristina; Valente, Lucila Maria; Sobral Filho, Dário Celestino; Barbosa e Silva, Odwaldo

    2015-01-01

    Impaired heart rate (HR) recovery after exercise testing is considered a predictor of cardiovascular mortality as it reflects vagus nerve dysfunction. To assess the relationship between body mass index (BMI) and HR recovery after exercise. We analyzed the records of 2443 patients of both sexes, aged between 20 and 59 years, in sinus rhythm, not using negative chronotropic agents and with no myocardial ischemic response to exercise testing carried out at a specialist clinic, between 2005 and 2011. BMI was categorized as normal (18.5-30 kg/m(2)). The different BMI groups were compared in terms of HR recovery after exercise, which was calculated as the difference between maximum HR during exercise and in the first minute of recovery. Recovery was considered impaired when the difference was ≤12 bpm. Eighty-seven (3.6%) patients presented impaired recovery, which was three times more prevalent in the obese group and twice as prevalent in the overweight group compared with the normal group (p<0.001 and p=0.010, respectively). Obese patients presented higher basal HR and lower maximum HR, as well as reduced chronotropic reserve (p<0.001). In multivariate analysis, impaired HR recovery was associated with overweight (relative risk [RR]=1.8; p=0.035), obesity (RR=2; p=0.016), number of metabolic equivalents (RR=0.82; p<0.001) and resting HR (RR=1.05; p<0.001). The hazard ratio for hypertension was 2 (p=0.083, NS). Impaired HR recovery was associated with higher BMI, demonstrating that obese individuals present vagus nerve dysfunction. Copyright © 2014 Sociedade Portuguesa de Cardiologia. Published by Elsevier España. All rights reserved.

  4. The Challenge of Validation: Assessing the Performance of a Test of Productive Vocabulary

    Science.gov (United States)

    Fitzpatrick, Tess; Clenton, Jon

    2010-01-01

    This paper assesses the performance of a vocabulary test designed to measure second language productive vocabulary knowledge.The test, Lex30, uses a word association task to elicit vocabulary, and uses word frequency data to measure the vocabulary produced. Here we report firstly on the reliability of the test as measured by a test-retest study, a…

  5. 76 FR 69585 - Testing and Labeling Pertaining to Product Certification Regarding Representative Samples for...

    Science.gov (United States)

    2011-11-08

    ... the applicable periodic testing interval. The number of samples selected for the sampling procedure... requirement to test representative samples, by requiring each manufacturer of a children's product to select... the last periodic test occurred (or since certification for the first periodic tests). In order...

  6. Testing the Altresyn Product for Oestrus Synchronization in Gilts

    Directory of Open Access Journals (Sweden)

    Liviu BOGDAN

    2017-05-01

    Full Text Available The aim of this study was to evaluate the effect of Altresyn® product (progesterone-based product as a method for synchronization of oestrus in gilts. The gilts were divided into three experimental groups. The synthetic progesterone Altrenogest was fed daily to 39 gilts at 20 mg/gilts for 18 days. In case of the first group (n = 11 gilts the treatment was performed using only Altresyn product. In group II (n=13 gilts was administered the prostaglandin hormone (Prosolvin, 0.75 mg at 24 hours after Altrenogest treatment suppression. Group III (n=15 gilts received one injections of PMSG hormone (Folligon, 500 IU/animal. Gilts were checked for oestrus twice daily and were artificially inseminated. All gilts expressed signs of oestrus between 3 and 6 days after withdrawal of Altrenogest. At the groups that were administered prostaglandin and PMSG there was a shorter duration of oestrus (group III - 26.66 hours, group II - 27.07 hours compared to group I (28.54 hours.  In this study, pregnancy rate ranged from 45.45% (group I and 93.33%(group III, while in group II the value slightly exceeded 50% (53.84%. In group I, the mean litter size was 11.6 piglets, in group II the mean value of farrowed piglets was 13.28 and 15 piglets in group III. Regarding the average number of weaned piglets in group I was 8.8, 12 in group II, while for the third group was 13.14. Altrenogest, the active ingredient in Altresyn® is effective for regulating the oestrus of gilts in commercial pig farms.

  7. Background information for Van Aken on testing of NESTT product

    Energy Technology Data Exchange (ETDEWEB)

    Reynolds, John G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2016-11-18

    Debris from explosives testing in a shot tank that contains 4 weight percent or less of explosive is shown to be non-reactive under the specified testing protocol in the Code of Federal Regulations. This debris can then be regarded as a non-hazardous waste on the basis of reactivity, when collected and packaged in a specified manner. If it is contaminated with radioactive components (e.g. depleted uranium), it can therefore be disposed of as radioactive waste or mixed waste, as appropriate (note that debris may contain other materials that render it hazardous, such as beryllium). We also discuss potential waste generation issues in contained firing operations that are applicable to the planned new Contained Firing Facility (CFF).

  8. Hybrid microcircuit technology handbook materials, processes, design, testing and production

    CERN Document Server

    Licari, James J

    1998-01-01

    The Hybrid Microcircuit Technology Handbook integrates the many diverse technologies used in the design, fabrication, assembly, and testing of hybrid segments crucial to the success of producing reliable circuits in high yields. Among these are: resistor trimming, wire bonding, die attachment, cleaning, hermetic sealing, and moisture analysis. In addition to thin films, thick films, and assembly processes, important chapters on substrate selections, handling (including electrostatic discharge), failure analysis, and documentation are included. A comprehensive chapter of design guidelines will

  9. Evaluation of experimental factors that influence the application and discrimination capability of the product consistency test

    Energy Technology Data Exchange (ETDEWEB)

    Shade, J.W.; Piepel, G.F.

    1991-06-01

    It is desirable to have a means of monitoring possible changes in waste glass durability during protection so that the product remains within acceptable limits. A leach test called the Product Consistency test (PCT) was developed by Savannah River Laboratory (SRL) as such a production test for the Defense Waste Processing Facility (DWPF). This report examines some of the experimental factors that may be used in the PCT that could influence test precision and its ability to function as intended. An experiment was performed to investigate the effects (on pH and elemental releases of Al, Fe, K, Na, Si, B, Li, and Mn) of modifications to the test conditions of the Product Consistency Test (PCT). The experiment was replicated three times; each replicate involved leach testing two glasses with each of 24 different sets of PCT conditions. 6 refs., 1 fig., 12 tabs.

  10. Mass production of chemicals from biomass-derived oil by directly atmospheric distillation coupled with co-pyrolysis

    Science.gov (United States)

    Zhang, Xue-Song; Yang, Guang-Xi; Jiang, Hong; Liu, Wu-Jun; Ding, Hong-Sheng

    2013-01-01

    Production of renewable commodity chemicals from bio-oil derived from fast pyrolysis of biomass has received considerable interests, but hindered by the presence of innumerable components in bio-oil. In present work, we proposed and experimentally demonstrated an innovative approach combining atmospheric distillation of bio-oil with co-pyrolysis for mass production of renewable chemicals from biomass, in which no waste was produced. It was estimated that 51.86 wt.% of distillate just containing dozens of separable organic components could be recovered using this approach. Ten protogenetic and three epigenetic compounds in distillate were qualitatively identified by gas chromatography/mass spectrometry and quantified by gas chromatography. Among them, the recovery efficiencies of acetic acid, propanoic acid, and furfural were all higher than 80 wt.%. Formation pathways of the distillate components in this process were explored. This work opens up a fascinating prospect for mass production of chemical feedstock from waste biomass. PMID:23350028

  11. Results from a round robin test for the ecotoxicological evaluation of construction products using two leaching tests and an aquatic test battery.

    Science.gov (United States)

    Gartiser, Stefan; Heisterkamp, Ines; Schoknecht, Ute; Burkhardt, Michael; Ratte, Monika; Ilvonen, Outi; Brauer, Frank; Brückmann, Jan; Dabrunz, André; Egeler, Philipp; Eisl, Andrea-Maria; Feiler, Ute; Fritz, Ines; König, Sabina; Lebertz, Herbert; Pandard, Pascal; Pötschke, Gabriele; Scheerbaum, Dirk; Schreiber, Frank; Soldán, Přemysl; Weiß, Roland; Weltens, Reinhilde

    2017-05-01

    A European round robin test according to ISO 5725-2 was conceptually prepared, realised, and evaluated. The aim was to determine the inter-laboratory variability of the overall process for the ecotoxicological characterization of construction products in eluates and bioassays. To this end, two construction products BAM-G1 (granulate) and HSR-2 (roof sealing sheet), both made of EPDM polymers (rubber), were selected. The granular construction product was eluted in a one stage batch test, the planar product in the Dynamic Surface Leaching test (DSLT). A total of 17 laboratories from 5 countries participated in the round robin test: Germany (12), Austria (2), Belgium (1), Czech Republic (1) and France (1). A test battery of four standardised ecotoxicity tests with algae, daphnia, luminescent bacteria and zebrafish eggs was used. As toxicity measures, EC50 and LID values were calculated. All tests, except the fish egg test, were basically able to demonstrate toxic effects and the level of toxicity. The reproducibility of test results depended on the test specimens and the test organisms. Generally, the variability of the EC50 or LID values increased with the overall level of toxicity. For the very toxic BAM-G1 eluate a relative high variability of CV = 73%-110% was observed for EC50 in all biotests, while for the less toxic HSR-2 eluate the reproducibility of EC50 varied with sensitivity: it was very good (CV = 9.3%) for the daphnia test with the lowest sensitivity, followed by the algae test (CV = 36.4%). The luminescent bacteria test, being the most sensitive bioassay for HSR-2 Eluate, showed the highest variability (CV = 74.8%). When considering the complex overall process the reproducibility of bioassays with eluates from construction products was acceptable. Copyright © 2017. Published by Elsevier Ltd.

  12. Testing multimass dynamical models of star clusters with real data: mass segregation in three Galactic globular clusters

    Science.gov (United States)

    Sollima, A.; Dalessandro, E.; Beccari, G.; Pallanca, C.

    2017-02-01

    We present the results of the analysis of deep photometric data for a sample of three Galactic globular clusters (NGC5466, NGC6218 and NGC 6981) with the aim of estimating their degree of mass segregation and testing the predictions of analytic dynamical models. The adopted data set, composed of both Hubble Space Telescope and ground-based data, reaches the low-mass end of the mass functions of these clusters from the centre up to their tidal radii allowing us to derive the radial distribution of stars with different masses. All the analysed clusters show evidence of mass segregation with the most massive stars being more concentrated than the low-mass ones. The structures of NGC5466 and NGC6981 are well reproduced by multimass dynamical models adopting a lowered Maxwellian distribution function and the prescription for mass segregation given by Gunn & Griffin. Instead, NGC6218 appears to be more mass segregated than model predictions. By applying the same technique to mock observations derived from snapshots selected from suitable N-body simulations, we show that the deviation from the behaviour predicted by these models depends on the particular stage of dynamical evolution regardless of initial conditions.

  13. A new methodology to test galaxy formation models using the dependence of clustering on stellar mass

    CERN Document Server

    Campbell, David J R; Mitchell, Peter D; Helly, John C; Gonzalez-Perez, Violeta; Lacey, Cedric G; Lagos, Claudia del P; Simha, Vimal; Farrow, Daniel J

    2014-01-01

    We present predictions for the two-point correlation function of galaxy clustering as a function of stellar mass, computed using two new versions of the GALFORM semi-analytic galaxy formation model. These models make use of a new high resolution, large volume N-body simulation, set in the WMAP7 cosmology. One model uses a universal stellar initial mass function (IMF), while the other assumes different IMFs for quiescent star formation and bursts. Particular consideration is given to how the assumptions required to estimate the stellar masses of observed galaxies (such as the choice of IMF, stellar population synthesis model and dust extinction) influence the perceived dependence of galaxy clustering on stellar mass. Broad-band spectral energy distribution fitting is carried out to estimate stellar masses for the model galaxies in the same manner as in observational studies. We show clear differences between the clustering signals computed using the true and estimated model stellar masses. As such, we highligh...

  14. Mass, energy and material balances of SRF production process. Part 3: solid recovered fuel produced from municipal solid waste.

    Science.gov (United States)

    Nasrullah, Muhammad; Vainikka, Pasi; Hannula, Janne; Hurme, Markku; Kärki, Janne

    2015-02-01

    This is the third and final part of the three-part article written to describe the mass, energy and material balances of the solid recovered fuel production process produced from various types of waste streams through mechanical treatment. This article focused the production of solid recovered fuel from municipal solid waste. The stream of municipal solid waste used here as an input waste material to produce solid recovered fuel is energy waste collected from households of municipality. This article presents the mass, energy and material balances of the solid recovered fuel production process. These balances are based on the proximate as well as the ultimate analysis and the composition determination of various streams of material produced in a solid recovered fuel production plant. All the process streams are sampled and treated according to CEN standard methods for solid recovered fuel. The results of the mass balance of the solid recovered fuel production process showed that 72% of the input waste material was recovered in the form of solid recovered fuel; 2.6% as ferrous metal, 0.4% as non-ferrous metal, 11% was sorted as rejects material, 12% as fine faction and 2% as heavy fraction. The energy balance of the solid recovered fuel production process showed that 86% of the total input energy content of input waste material was recovered in the form of solid recovered fuel. The remaining percentage (14%) of the input energy was split into the streams of reject material, fine fraction and heavy fraction. The material balances of this process showed that mass fraction of paper and cardboard, plastic (soft) and wood recovered in the solid recovered fuel stream was 88%, 85% and 90%, respectively, of their input mass. A high mass fraction of rubber material, plastic (PVC-plastic) and inert (stone/rock and glass particles) was found in the reject material stream. © The Author(s) 2014.

  15. 46 CFR 164.013-6 - Production tests, inspections, and marking.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 6 2010-10-01 2010-10-01 false Production tests, inspections, and marking. 164.013-6..., CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL MATERIALS Foam, Unicellular Polyethylene (Buoyant, Slab, Slitted Trigonal Pattern) § 164.013-6 Production tests, inspections, and marking. Manufacturers...

  16. 76 FR 3679 - Market Test of Experimental Product: “Marketing Mail Made Easy”

    Science.gov (United States)

    2011-01-20

    ... of Experimental Product: ``Marketing Mail Made Easy'' AGENCY: Postal Service TM . ACTION: Notice. SUMMARY: The Postal Service gives notice of a market test of an experimental product in accordance with... 39 U.S.C. 3641(c)(1) that it will begin a market test of its ``Marketing Mail Made...

  17. 21 CFR 211.110 - Sampling and testing of in-process materials and drug products.

    Science.gov (United States)

    2010-04-01

    ... PHARMACEUTICALS Production and Process Controls § 211.110 Sampling and testing of in-process materials and drug... production process, e.g., at commencement or completion of significant phases or after storage for long... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Sampling and testing of in-process materials...

  18. 15 CFR 996.12 - Development of standards compliance tests for a hydrographic product or class.

    Science.gov (United States)

    2010-01-01

    ... Quality Assurance Program for Hydrographic Products § 996.12 Development of standards compliance tests for... 15 Commerce and Foreign Trade 3 2010-01-01 2010-01-01 false Development of standards compliance tests for a hydrographic product or class. 996.12 Section 996.12 Commerce and Foreign Trade...

  19. Evaluation of long-term gas hydrate production testing locations on the Alaska North Slope

    Science.gov (United States)

    Collett, Timothy S.; Boswell, Ray; Lee, Myung W.; Anderson, Brian J.; Rose, Kelly K.; Lewis, Kristen A.

    2012-01-01

    The results of short-duration formation tests in northern Alaska and Canada have further documented the energy-resource potential of gas hydrates and have justified the need for long-term gas-hydrate-production testing. Additional data acquisition and long-term production testing could improve the understanding of the response of naturally occurring gas hydrate to depressurization-induced or thermal-, chemical-, or mechanical-stimulated dissociation of gas hydrate into producible gas. The Eileen gashydrate accumulation located in the Greater Prudhoe Bay area in northern Alaska has become a focal point for gas-hydrate geologic and production studies. BP Exploration (Alaska) Incorporated and ConocoPhillips have each established research partnerships with the US Department of Energy to assess the production potential of gas hydrates in northern Alaska. A critical goal of these efforts is to identify the most suitable site for production testing. A total of seven potential locations in the Prudhoe Bay, Kuparuk River, and Milne Point production units were identified and assessed relative to their suitability as a long-term gas-hydrate-production test sites. The test-site-assessment criteria included the analysis of the geologic risk associated with encountering reservoirs for gas-hydrate testing. The site-selection process also dealt with the assessment of the operational/logistical risk associated with each of the potential test sites. From this review, a site in the Prudhoe Bay production unit was determined to be the best location for extended gas-hydrate-production testing. The work presented in this report identifies the key features of the potential test site in the Greater Prudhoe Bay area and provides new information on the nature of gas-hydrate occurrence and the potential impact of production testing on existing infrastructure at the most favorable sites. These data were obtained from well-log analysis, geological correlation and mapping, and numerical

  20. Les méthodesthermiques de production des hydrocarbures. Chapitre 1 : transfert de chaleur et de masse Thermal Methods of Hydrocarbon Production. Chapter 1 : Heat and Mass Transfer

    Directory of Open Access Journals (Sweden)

    Bia P.

    2006-11-01

    Full Text Available Après un rappel général sur le transfert de chaleur et de masse ainsi que sur les lois de conservation dans les milieux continus, on traite de l'adaptation de ces lois au cas des milieux poreux. On donne ensuite des informations quantitatives sur les grandeurs physiques mises en jeu par les phénomènes de transfert en milieu poreux. After making a general review of heat and mass transfer a well as of laws of conservation in continua, this chapter describes how these laws con be adopted to the case of porous media. Quantitative data are then given on the physical magnitudes brought into play by transfer phenomena in porous media.

  1. GridPix detectors: Production and beam test results

    Energy Technology Data Exchange (ETDEWEB)

    Koppert, W.J.C., E-mail: wkoppert@nikhef.nl [Nikhef, Amsterdam (Netherlands); Bakel, N. van [Nikhef, Amsterdam (Netherlands); Bilevych, Y. [Physikalisches Institut, University of Bonn, Bonn (Germany); Colas, P. [IRFU, CEA Saclay, Gif-sur-Yvette (France); Desch, K. [Physikalisches Institut, University of Bonn, Bonn (Germany); Fransen, M.; Graaf, H. van der; Hartjes, F.; Hessey, N.P. [Nikhef, Amsterdam (Netherlands); Kaminski, J. [Physikalisches Institut, University of Bonn, Bonn (Germany); Schmitz, J. [University of Twente, Mesa Institute for Nanotechnology, Enschede (Netherlands); Schön, R.; Zappon, F. [Nikhef, Amsterdam (Netherlands)

    2013-12-21

    The innovative GridPix detector is a Time Projection Chamber (TPC) that is read out with a Timepix-1 pixel chip. By using wafer post-processing techniques an aluminium grid is placed on top of the chip. When operated, the electric field between the grid and the chip is sufficient to create electron induced avalanches which are detected by the pixels. The time-to-digital converter (TDC) records the drift time enabling the reconstruction of high precision 3D track segments. Recently GridPixes were produced on full wafer scale, to meet the demand for more reliable and cheaper devices in large quantities. In a recent beam test the contribution of both diffusion and time walk to the spatial and angular resolutions of a GridPix detector with a 1.2 mm drift gap are studied in detail. In addition long term tests show that in a significant fraction of the chips the protection layer successfully quenches discharges, preventing harm to the chip.

  2. GridPix detectors: Production and beam test results

    Science.gov (United States)

    Koppert, W. J. C.; van Bakel, N.; Bilevych, Y.; Colas, P.; Desch, K.; Fransen, M.; van der Graaf, H.; Hartjes, F.; Hessey, N. P.; Kaminski, J.; Schmitz, J.; Schön, R.; Zappon, F.

    2013-12-01

    The innovative GridPix detector is a Time Projection Chamber (TPC) that is read out with a Timepix-1 pixel chip. By using wafer post-processing techniques an aluminium grid is placed on top of the chip. When operated, the electric field between the grid and the chip is sufficient to create electron induced avalanches which are detected by the pixels. The time-to-digital converter (TDC) records the drift time enabling the reconstruction of high precision 3D track segments. Recently GridPixes were produced on full wafer scale, to meet the demand for more reliable and cheaper devices in large quantities. In a recent beam test the contribution of both diffusion and time walk to the spatial and angular resolutions of a GridPix detector with a 1.2 mm drift gap are studied in detail. In addition long term tests show that in a significant fraction of the chips the protection layer successfully quenches discharges, preventing harm to the chip.

  3. Technology of Mass Rearing Clostera anachoreta and Production of CaGV

    Institute of Scientific and Technical Information of China (English)

    HUYajun; LIANGHongzhu; ZHANGQiushuan; HOUZhengrong

    2004-01-01

    A new technique for mass rearing Clostera anachoreta(C.) was developed through a large number of experiments, so the problem of mass produce of CaGV was solved. The process of CaGV was discussed in detail.

  4. Knowledge productivity : designing and testing a method to diagnose knowledge productivity and plan for enhancement

    NARCIS (Netherlands)

    Stam, Christiaan David

    2007-01-01

    Our economy has changed from an industrial into a knowledge economy in which knowledge productivity has become the main challenge. The lack of appropriate techniques to reveal knowledge productivity hinders organizations to design effective policies aiming at improving knowledge-based performance. T

  5. Urea-formaldehyde resins: production, application, and testing

    Science.gov (United States)

    Nuryawan, A.; Risnasari, I.; Sucipto, T.; Heri Iswanto, A.; Rosmala Dewi, R.

    2017-07-01

    Urea-formaldehyde (UF) resin, one of the most important formaldehyde resin adhesives, is a polymeric condensation product of formaldehyde with urea, and being widely used for the manufacture of wood-based composite panels, such as plywood, particleboard, and fiberboard. In spite of its benefits such as fast curing, good performance in the panels (colorless), and lower cost; formaldehyde emission (FE) originated from either UF resin itself or composite products bonded by UF resins is considered a critical drawback as it affects human health particularly in indoor environment. In order to reduce the FE, lowering formaldehyde/urea (F/U) mole ratio in the synthesis of the UF resin was done. In this study, synthesis of UF resins was carried out following the conventional alkaline-acid two-step reaction with a second addition of urea, resulting in F/U mole ratio around 1.0, namely 0.95; 1.05, and 1.15. The UF resins produced were used as binder for particleboard making. The board was manufactured in the laboratory using shaving type particle of Gmelina wood, 8% UF resin based on oven dry particle, and 1% NH4Cl (20%wt) as hardener for the resin. The target of the thickness was 10 mm and the dimension was 25 cm x 25 cm. The resulted particleboard then was evaluated the physical and the mechanical properties by Japanese Industrial Standard (JIS) A 5908 (2003). Further, the resulted particleboard also was used for the mice cage’s wall in order to mimic the real living environment. After four weeks exposure in the cages, the mice then were evaluated their mucous organs as well as their blood. The experiment results were as follows: 1) It was possible to synthesis UF resins with low F/U mole ratio; 2) However, the particleboard bonded UF resins with low F/U mole ratio showed poor properties, particularly on the thickness swelling and modulus of elasticity; 3) There was no significant differences among the mucous organs of the mice after a month exposure FE originated from

  6. Intermediate mass dilepton production in a chemically equilibrating quark-gluon matter

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    We find that in a chemically equilibrating baryon-rich quark-gluon matter, due to the slow cooling rate, high initial temperature, large gluon density as well as large fusion cross section ofin the intermediate mass region, the gluon fusion provides a dominant contribution to dileptons with intermediate masses, resulting in the significant enhancement of intermediate mass dileptons.

  7. Testing the Reliability of Cluster Mass Indicators with a Systematics Limited Dataset

    CERN Document Server

    Juett, Adrienne M; Mushotzky, Richard

    2009-01-01

    We present the mass-X-ray observable scaling relationships for clusters of galaxies using the XMM-Newton cluster catalog of Snowden et al. Our results are roughly consistent with previous observational and theoretical work, with one major exception. We find 2-3 times the scatter around the best fit mass scaling relationships as expected from cluster simulations or seen in other observational studies. We suggest that this is a consequence of using hydrostatic mass, as opposed to virial mass, and is due to the explicit dependence of the hydrostatic mass on the gradients of the temperature and gas density profiles. We find a larger range of slope in the cluster temperature profiles at r_{500} than previous observational studies. Additionally, we find only a weak dependence of the gas mass fraction on cluster mass, consistent with a constant. Our average gas mass fraction results argue for a closer study of the systematic errors due to instrumental calibration and analysis method variations. We suggest that a mor...

  8. Design, production and testing of PMN-PT electrostrictive transducers.

    Science.gov (United States)

    Coutte, J; Dubus, B; Debus, J C; Granger, C; Jones, D

    2002-05-01

    Lead magnesium niobate ceramics (PMN) are promising materials for application in the field of high power transducers. The advantage of PMN materials are the large strains generated under moderate electric field and the low hysteresis. The electrostrictive effect is non-linear, the corresponding physical constants depend on temperature and frequency and a DC electrical bias is required. These difficulties must be considered at the design stage. A finite element model has been developed and validated in the ATILA code for non-linear static and time-domain analyses. These numerical modelings are used to design and test two Langevin-type electrostrictive transducers. The first transducer is made of PMN-PT-La (90-10-1%) ceramics (TRS Ceramics), the second one of ESCI ceramics (Morgan Matroc). For given static mechanical prestresses, resonance frequencies and effective coupling coefficients are measured at different DC electric fields and temperatures.

  9. Detection of Staphylococcus aureus delta-toxin production by whole-cell MALDI-TOF mass spectrometry.

    Directory of Open Access Journals (Sweden)

    Julie Gagnaire

    Full Text Available The aim of the present study was to detect the Staphylococcus aureus delta-toxin using Whole-Cell (WC Matrix Assisted Laser Desorption Ionization-Time-of-Flight (MALDI-TOF mass spectrometry (MS, correlate delta-toxin expression with accessory gene regulator (agr status, and assess the prevalence of agr deficiency in clinical isolates with and without resistance to methicillin and glycopeptides. The position of the delta-toxin peak in the mass spectrum was identified using purified delta-toxin and isogenic wild type and mutant strains for agr-rnaIII, which encodes delta-toxin. Correlation between delta-toxin production and agr RNAIII expression was assessed by northern blotting. A series of 168 consecutive clinical isolates and 23 unrelated glycopeptide-intermediate S. aureus strains (GISA/heterogeneous GISA were then tested by WC-MALDI-TOF MS. The delta-toxin peak was detected at 3005±5 Thomson, as expected for the naturally formylated delta toxin, or at 3035±5 Thomson for its G10S variant. Multivariate analysis showed that chronicity of S. aureus infection and glycopeptide resistance were significantly associated with delta-toxin deficiency (p = 0.048; CI 95%: 1.01-10.24; p = 0.023; CI 95%: 1.20-12.76, respectively. In conclusion, the S. aureus delta-toxin was identified in the WC-MALDI-TOF MS spectrum generated during routine identification procedures. Consequently, agr status can potentially predict infectious complications and rationalise application of novel virulence factor-based therapies.

  10. Development Strategies for Herbal Products Reducing the Influence of Natural Variance in Dry Mass on Tableting Properties and Tablet Characteristics

    Directory of Open Access Journals (Sweden)

    Firas Alshihabi

    2012-10-01

    Full Text Available One “Quality by Design” approach is the focus on the variability of the properties of the active substance. This is crucially important for active substances that are obtained from natural resources such as herbal plant material and extracts. In this paper, we present various strategies for the development of herbal products especially taking into account the natural batch-to-batch variability (mainly of the dry mass of tablets that contain a fixed amount of tincture. The following steps in the development have been evaluated for the outcome of the physico-chemical properties of the resulting tablets and intermediates: concentration of the tincture extracted from Echinacea fresh plant, loading of the concentrate onto an inert carrier, the respective wet granulation and drying step, including milling, and the adjuvant excipients for the tablet compression step. The responses that were investigated are the mean particle size of the dried and milled granulates, compaction properties and disintegration time of the tablets. Increased particle size showed a significant increase of the disintegration time and a decrease of the compaction properties. In addition, our results showed that the particle size has a great dependency on the ratio of liquid to carrier during the wet granulation process. Thus, the variability of the respective parameters tested was influenced by the performed strategies, which is how the tincture correlated to its dry mass and the relation of the amount of carrier used. In order to optimize these parameters, a strategy considering the above-mentioned points has to be chosen.

  11. Moving Technologies from the Test Tube to Commercial Products

    Science.gov (United States)

    Bryant, Robert G.

    2013-01-01

    Successful technologies include objects, processes, and procedures that share a common theme; they are being used to generate new products that create economic growth. The foundation is the invention, but the invention is a small part of the overall effort. The pathway to success is understanding the competition, proper planning, record keeping, integrating a supply chain, understanding actual costs, intellectual property (IP), benchmarking, and timing. Additionally, there are obstacles that include financing, what to make, buy, and sell, and the division of labor i.e. recognizing who is best at what task. Over the past two decades, NASA Langley Research Center (LaRC) has developed several commercially available technologies. The approach to commercialization of three of these inventions; Langley Research Center-Soluble Imide (LaRC-SI, Imitec Inc.), the Thin Layer Unimorph Driver (THUNDER, FACE International), and the Macrofiber Composite (MFC, Smart Material Corp.) will be described, as well as some of the lessons learned from the process. What makes these three inventions interesting is that one was created in the laboratory; another was built using the previous invention as part of its process, and the last one was created by packaging commercial-off-the-shelf (COTS) materials thereby creating a new component.

  12. Beyond the Main Sequence: Testing the accuracy of stellar masses predicted by the PARSEC evolutionary tracks

    CERN Document Server

    Ghezzi, Luan

    2015-01-01

    Characterizing the physical properties of exoplanets, and understanding their formation and orbital evolution requires precise and accurate knowledge of the physical properties of their host stars. Accurately measuring stellar mass is particularly important because the masses of host stars likely influence planet occurrence and the architectures of planetary systems observed today. Single main-sequence stars typically have masses estimated from evolutionary tracks, which generally provide accurate results due to their extensive empirical calibration. However, the validity of this method for subgiants and giants has been called into question, with suggestions that the evolutionary models could contain systematic errors that would cause mass estimates of these evolved stars to be overestimated. We investigate these concerns using a sample of 59 benchmark evolved stars with model-independent masses (from binary systems or asteroseismology) obtained from the extant literature. We find very good agreement between ...

  13. Testing the Asteroseismic Mass Scale Using Metal-Poor Stars Characterized with APOGEE and Kepler

    CERN Document Server

    Epstein, Courtney R; Johnson, Jennifer A; Shetrone, Matthew; Mosser, Benoît; Hekker, Saskia; Tayar, Jamie; Harding, Paul; Pinsonneault, Marc; Aguirre, Víctor Silva; Basu, Sarbani; Beers, Timothy C; Bizyaev, Dmitry; Bedding, Timothy R; Chaplin, William J; Frinchaboy, Peter M; García, Rafael A; Pérez, Ana E García; Hearty, Fred R; Huber, Daniel; Ivans, Inese I; Majewski, Steven R; Mathur, Savita; Nidever, David; Serenelli, Aldo; Schiavon, Ricardo P; Schneider, Donald P; Schönrich, Ralph; Sobeck, Jennifer S; Stassun, Keivan G; Stello, Dennis; Zasowski, Gail

    2014-01-01

    Fundamental stellar properties, such as mass, radius, and age, can be inferred using asteroseismology. Cool stars with convective envelopes have turbulent motions that can stochastically drive and damp pulsations. The properties of the oscillation frequency power spectrum can be tied to mass and radius through solar-scaled asteroseismic relations. Stellar properties derived using these scaling relations need verification over a range of metallicities. Because the age and mass of halo stars are well-constrained by astrophysical priors, they provide an independent, empirical check on asteroseismic mass estimates in the low-metallicity regime. We identify nine metal-poor red giants (including six stars that are kinematically associated with the halo) from a sample observed by both the Kepler space telescope and the Sloan Digital Sky Survey-III APOGEE spectroscopic survey. We compare masses inferred using asteroseismology to those expected for halo and thick-disk stars. Although our sample is small, standard scal...

  14. Mass, energy and material balances of SRF production process. Part 1: SRF produced from commercial and industrial waste.

    Science.gov (United States)

    Nasrullah, Muhammad; Vainikka, Pasi; Hannula, Janne; Hurme, Markku; Kärki, Janne

    2014-08-01

    This paper presents the mass, energy and material balances of a solid recovered fuel (SRF) production process. The SRF is produced from commercial and industrial waste (C&IW) through mechanical treatment (MT). In this work various streams of material produced in SRF production process are analyzed for their proximate and ultimate analysis. Based on this analysis and composition of process streams their mass, energy and material balances are established for SRF production process. Here mass balance describes the overall mass flow of input waste material in the various output streams, whereas material balance describes the mass flow of components of input waste stream (such as paper and cardboard, wood, plastic (soft), plastic (hard), textile and rubber) in the various output streams of SRF production process. A commercial scale experimental campaign was conducted on an MT waste sorting plant to produce SRF from C&IW. All the process streams (input and output) produced in this MT plant were sampled and treated according to the CEN standard methods for SRF: EN 15442 and EN 15443. The results from the mass balance of SRF production process showed that of the total input C&IW material to MT waste sorting plant, 62% was recovered in the form of SRF, 4% as ferrous metal, 1% as non-ferrous metal and 21% was sorted out as reject material, 11.6% as fine fraction, and 0.4% as heavy fraction. The energy flow balance in various process streams of this SRF production process showed that of the total input energy content of C&IW to MT plant, 75% energy was recovered in the form of SRF, 20% belonged to the reject material stream and rest 5% belonged with the streams of fine fraction and heavy fraction. In the material balances, mass fractions of plastic (soft), plastic (hard), paper and cardboard and wood recovered in the SRF stream were 88%, 70%, 72% and 60% respectively of their input masses to MT plant. A high mass fraction of plastic (PVC), rubber material and non

  15. Mass production of highly-porous graphene for high-performance supercapacitors

    Science.gov (United States)

    Amiri, Ahmad; Shanbedi, Mehdi; Ahmadi, Goodarz; Eshghi, Hossein; Kazi, S. N.; Chew, B. T.; Savari, Maryam; Zubir, Mohd Nashrul Mohd

    2016-09-01

    This study reports on a facile and economical method for the scalable synthesis of few-layered graphene sheets by the microwave-assisted functionalization. Herein, single-layered and few-layered graphene sheets were produced by dispersion and exfoliation of functionalized graphite in ethylene glycol. Thermal treatment was used to prepare pure graphene without functional groups, and the pure graphene was labeled as thermally-treated graphene (T-GR). The morphological and statistical studies about the distribution of the number of layers showed that more than 90% of the flakes of T-GR had less than two layers and about 84% of T-GR were single-layered. The microwave-assisted exfoliation approach presents us with a possibility for a mass production of graphene at low cost and great potentials in energy storage applications of graphene-based materials. Owing to unique surface chemistry, the T-GR demonstrates an excellent energy storage performance, and the electrochemical capacitance is much higher than that of the other carbon-based nanostructures. The nanoscopic porous morphology of the T-GR-based electrodes made a significant contribution in increasing the BET surface as well as the specific capacitance of graphene. T-GR, with a capacitance of 354.1 Fg-1 at 5 mVs-1 and 264 Fg-1 at 100 mVs-1, exhibits excellent performance as a supercapacitor.

  16. Formulation of a low-cost medium for mass production of Spirulina

    Energy Technology Data Exchange (ETDEWEB)

    Raoof, Basirath [Division of Microbiology, Indian Agricultural Research Institute, New Delhi 110 012 (India); Kaushik, B.D. [Division of Microbiology, Indian Agricultural Research Institute, New Delhi 110 012 (India)]. E-mail: bdkaushik@hotmail.com; Prasanna, Radha [Centre for Conservation and Utilization of Blue-Green Algae, Indian Agricultural Research Institute, New Delhi, 110 012 (India)

    2006-06-15

    A new medium was formulated for mass production of Spirulina sp. by incorporating selected nutrients of the standard Zarrouk's medium (SM) and other cost-effective alternative chemicals. This newly formulated medium (RM{sub 6}) contains single super phosphate (1.25 g l{sup -1}), sodium nitrate (2.50 g l{sup -1}), muriate of potash (0.98 g l{sup -1}), sodium chloride (0.5 g l{sup -1}), magnesium sulphate (0.15 g l{sup -1}), calcium chloride (0.04 g l{sup -1}), and sodium bicarbonate (commercial grade) 8 g l{sup -1}. The alga was grown in an illuminated (50 {mu}mol photons m{sup -2} s{sup -1} white light) growth room at 30{+-}1 {sup o}C. Maximum growth rate in terms of dry biomass, chlorophyll and proteins in SM was recorded between 6 and 9 days of growth and values were 0.114, 0.003 and 0.068 as compared to 0.112, 0.003 and 0.069 mg ml{sup -1} d{sup -1} in RM{sub 6},. No significant differences were observed in the protein profiles of Spirulina sp. grown in both the media. From the scale up point of view, the revised medium was found to be highly economical, since it is five times cheaper than Zarrouk's medium.

  17. Research and development of shallow algal mass culture systems for the production of oils

    Energy Technology Data Exchange (ETDEWEB)

    Laws, E.A.

    1984-10-01

    The major accomplishment of the past nine months' work was the identification of a microalgal species which can be grown in the system on a 12-month basis without temperature control. The most promising species identified to date is a strain of platymonas sp. This strain grows rapidly at temperatures from 20/sup 0/ to 34/sup 0/C, and at salinities from 1.5 to 3.5%. Neither the lower temperature limit nor the lower salinity limit of the strain are known at this time. A factorial experiment designed to determine optimum growth conditions indicated that the optimum culture depth was 10 cm, the optimum pH about 7.5, and the optimum flow rate about 30 cm/s. A major discovery was that diluting the culture every third day greatly enhanced production. In this dilution mode daily yields averaged 46 g/m/sup 2/ ash-free dry weight (AFDW) over a one-month period, and photosynthetic efficiencies averaged 11% (based on visible light energy). The former figure is over twice the best long-term yields achieved in microalgal mass culture systems grown exclusively on inorganic nutrients.

  18. MASS PRODUCTION OF NANOPARTICLES BY HIGH GRAVITY REACTIVE PRECIPITATION TECHNOLOGY WITH LOW COST

    Institute of Scientific and Technical Information of China (English)

    Jianfeng Chen; Lei Shao

    2003-01-01

    Mass production of nanoparticles at low cost has attracted much attention from industrial and academic circles. In this paper, a novel method, the high gravity reactive precipitation (HGRP) technology, of manufacturing CaCO3 nanoparticles, presently scaled-up to an annual capacity of 10,000 tons, is presented. This paper describes the process principle, the process design and experiments on the syntheses of 15-30 nm CaCO3, 30-50 nm SiO2,20-30 nm TiO2, 20-60 nm ZnO, 20-30 nm ZnS, 30 nm SrCO3, 40-70 nm BaTiO3, stick-like nano BaCO3 as well as nano-fibrillar aluminum hydroxide measuring 1-10 nm in diameter and 50-300 nm in length, using liquid-liquid,gas-liquid and gas-liquid-solid reactant systems. The advantage of using the HGRP technology is illustrated by comparison to conventional methods.

  19. INVESTIGATION OF THE RELATIONSHIP OF THE STATISTICAL MOMENTS OF THE FAT PHASE MASS DISTRIBUTION AND RELAXATION SPECTRA OF DAIRY PRODUCTS

    OpenAIRE

    V. E. Merzlikin

    2015-01-01

    The article deals with the search for optimal parameter estimation of the parameters of the process of homogenization of dairy products. Provides a theoretical basis for relationship of the relaxation time of the fat globules and attenuation coefficient of ultrasonic oscillations in dairy products. Suggested from the measured acoustic properties of milk to make the calculations of the mass distribution of fat globules. Studies on the proof of this hypothesis. Morphological analysis procedure ...

  20. Assessment for the Masses: A Historical Critique of High-Stakes Testing in Reading

    Science.gov (United States)

    Huddleston, Andrew P.; Rockwell, Elizabeth C.

    2015-01-01

    This historical critique of high-stakes testing in reading focuses on selected events from three historical movements: 1) the history of standardized testing, 2) the history of standardized reading tests, and 3) the history of high-stakes testing. These three interrelated histories have produced the high-stakes, standardized reading tests used in…

  1. BEYOND THE MAIN SEQUENCE: TESTING THE ACCURACY OF STELLAR MASSES PREDICTED BY THE PARSEC EVOLUTIONARY TRACKS

    Energy Technology Data Exchange (ETDEWEB)

    Ghezzi, Luan; Johnson, John Asher, E-mail: lghezzi@cfa.harvard.edu [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street, Cambridge, MA 02138 (United States)

    2015-10-20

    Characterizing the physical properties of exoplanets and understanding their formation and orbital evolution requires precise and accurate knowledge of their host stars. Accurately measuring stellar masses is particularly important because they likely influence planet occurrence and the architectures of planetary systems. Single main-sequence stars typically have masses estimated from evolutionary tracks, which generally provide accurate results due to their extensive empirical calibration. However, the validity of this method for subgiants and giants has been called into question by recent studies, with suggestions that the masses of these evolved stars could have been overestimated. We investigate these concerns using a sample of 59 benchmark evolved stars with model-independent masses (from binary systems or asteroseismology) obtained from the literature. We find very good agreement between these benchmark masses and the ones estimated using evolutionary tracks. The average fractional difference in the mass interval ∼0.7–4.5 M{sub ⊙} is consistent with zero (−1.30 ± 2.42%), with no significant trends in the residuals relative to the input parameters. A good agreement between model-dependent and -independent radii (−4.81 ± 1.32%) and surface gravities (0.71 ± 0.51%) is also found. The consistency between independently determined ages for members of binary systems adds further support for the accuracy of the method employed to derive the stellar masses. Taken together, our results indicate that determination of masses of evolved stars using grids of evolutionary tracks is not significantly affected by systematic errors, and is thus valid for estimating the masses of isolated stars beyond the main sequence.

  2. Targeted natural products discovery from marine cyanobacteria using combined phylogenetic and mass spectrometric evaluation.

    Science.gov (United States)

    Salvador-Reyes, Lilibeth A; Engene, Niclas; Paul, Valerie J; Luesch, Hendrik

    2015-03-27

    Combined phylogenetic and HPLC-MS-based natural products dereplication methods aimed at identifying cyanobacterial collections containing the potent cytotoxins largazole, dolastatin 10, and symplostatin 1 were developed. The profiling of the phylogeny, chemical space, and antiproliferative activity of cyanobacterial collections served to streamline the prioritization of samples for the discovery of new secondary metabolites. The dereplication methods highlighted the biosynthetic potential and combinatorial pharmacology employed by marine cyanobacteria. We found that largazole was always coproduced with dolastatin 10 or with symplostatin 1 and consequently tested combinations of these agents against colon cancer cells. Combinatorial regimens of largazole and dolastatin 10 aimed at curbing the growth of HCT116 cancer cells showed cooperative activity.

  3. Testing improvements in the chocolate traceability system: Impact on product recalls and production efficiency

    DEFF Research Database (Denmark)

    Saltini, Rolando; Akkerman, Renzo

    2012-01-01

    hypothetical improvements of the traceability system within the chocolate production system and supply chain and we illustrate the resulting benefits by using a case study. Based on the case study, we quantify the influence of these improvements on production efficiency and recall size in case of a safety...... crisis by developing a simulation tool. These results are aimed to illustrate and quantify the additional benefits of traceability information, and could help food industries in deciding whether and how to improve their traceability systems....

  4. CP violating phase from minimal texture neutrino mass matrix: Test of the phase relevant to leptogenesis

    CERN Document Server

    Fukugita, Masataka; Shimizu, Yusuke; Tanimoto, Morimitsu; Yanagida, Tsutomu T

    2016-01-01

    The model of neutrino mass matrix with minimal texture is now tightly constrained by experiment so that it can yield a prediction for the phase of CP violation. This phase is predicted to lie in the range $\\delta_{CP}=0.77\\pi - 1.24\\pi$. If neutrino oscillation experiment would find the CP violation phase outside this range, this means that the minimal-texture neutrino mass matrix, the element of which is all real, fails and the neutrino mass matrix must be complex, i.e., the phase must be present that is responsible for leptogenesis.

  5. Confirmation of synthetic glucocorticoids with liquid chromatography/mass spectrometry: Organization and results of an international interlaboratory comparison test

    NARCIS (Netherlands)

    Hauwe, O. van den; Campbell, K.; Crooks, S.R.H.; Schilt, R.; Peteghem, C.H. van

    2005-01-01

    Within the framework of a European Union (EU) research project entitled "Food Safety Screening: Synthetic Glucocorticoids (QLK1-1999-00122)," an international interlaboratory ring test was organized to compare and evaluate different liquid chromatography/mass spectrometry (LC/MS) confirmatory method

  6. Confirmation of synthetic glucocorticoids with liquid chromatography/mass spectrometry: Organization and results of an international interlaboratory comparison test

    NARCIS (Netherlands)

    Hauwe, O. van den; Campbell, K.; Crooks, S.R.H.; Schilt, R.; Peteghem, C.H. van

    2005-01-01

    Within the framework of a European Union (EU) research project entitled "Food Safety Screening: Synthetic Glucocorticoids (QLK1-1999-00122)," an international interlaboratory ring test was organized to compare and evaluate different liquid chromatography/mass spectrometry (LC/MS) confirmatory

  7. Analysis of diffractive pd to Xd and pp to Xp interactions and test of the finite-mass sum rule

    CERN Document Server

    Akimov, Y; Golovanov, L B; Goulianos, K; Gross, D; Malamud, E; Melissinos, A C; Mukhin, S; Nitz, D; Olsen, S; Sticker, H; Tsarev, V A; Yamada, R; Zimmerman, P

    1976-01-01

    The first moment finite mass sum rule is tested by utilising cross- sections for pp to Xp extracted from recent Fermilab data on pd to Xd and also comparing with CERN ISR data. The dependences on M/sub x//sup 2/, t and s are also discussed. (11 refs).

  8. Standard test method for isotopic analysis of uranium hexafluoride by double standard single-collector gas mass spectrometer method

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2010-01-01

    1.1 This is a quantitative test method applicable to determining the mass percent of uranium isotopes in uranium hexafluoride (UF6) samples with 235U concentrations between 0.1 and 5.0 mass %. 1.2 This test method may be applicable for the entire range of 235U concentrations for which adequate standards are available. 1.3 This test method is for analysis by a gas magnetic sector mass spectrometer with a single collector using interpolation to determine the isotopic concentration of an unknown sample between two characterized UF6 standards. 1.4 This test method is to replace the existing test method currently published in Test Methods C761 and is used in the nuclear fuel cycle for UF6 isotopic analyses. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appro...

  9. Metabolic heat production and thermal conductance are mass-independent adaptations to thermal environment in birds and mammals.

    Science.gov (United States)

    Fristoe, Trevor S; Burger, Joseph R; Balk, Meghan A; Khaliq, Imran; Hof, Christian; Brown, James H

    2015-12-29

    The extent to which different kinds of organisms have adapted to environmental temperature regimes is central to understanding how they respond to climate change. The Scholander-Irving (S-I) model of heat transfer lays the foundation for explaining how endothermic birds and mammals maintain their high, relatively constant body temperatures in the face of wide variation in environmental temperature. The S-I model shows how body temperature is regulated by balancing the rates of heat production and heat loss. Both rates scale with body size, suggesting that larger animals should be better adapted to cold environments than smaller animals, and vice versa. However, the global distributions of ∼9,000 species of terrestrial birds and mammals show that the entire range of body sizes occurs in nearly all climatic regimes. Using physiological and environmental temperature data for 211 bird and 178 mammal species, we test for mass-independent adaptive changes in two key parameters of the S-I model: basal metabolic rate (BMR) and thermal conductance. We derive an axis of thermal adaptation that is independent of body size, extends the S-I model, and highlights interactions among physiological and morphological traits that allow endotherms to persist in a wide range of temperatures. Our macrophysiological and macroecological analyses support our predictions that shifts in BMR and thermal conductance confer important adaptations to environmental temperature in both birds and mammals.

  10. Mass, energy and material balances of SRF production process. Part 2: SRF produced from construction and demolition waste.

    Science.gov (United States)

    Nasrullah, Muhammad; Vainikka, Pasi; Hannula, Janne; Hurme, Markku; Kärki, Janne

    2014-11-01

    In this work, the fraction of construction and demolition waste (C&D waste) complicated and economically not feasible to sort out for recycling purposes is used to produce solid recovered fuel (SRF) through mechanical treatment (MT). The paper presents the mass, energy and material balances of this SRF production process. All the process streams (input and output) produced in MT waste sorting plant to produce SRF from C&D waste are sampled and treated according to CEN standard methods for SRF. Proximate and ultimate analysis of these streams is performed and their composition is determined. Based on this analysis and composition of process streams their mass, energy and material balances are established for SRF production process. By mass balance means the overall mass flow of input waste material stream in the various output streams and material balances mean the mass flow of components of input waste material stream (such as paper and cardboard, wood, plastic (soft), plastic (hard), textile and rubber) in the various output streams of SRF production process. The results from mass balance of SRF production process showed that of the total input C&D waste material to MT waste sorting plant, 44% was recovered in the form of SRF, 5% as ferrous metal, 1% as non-ferrous metal, and 28% was sorted out as fine fraction, 18% as reject material and 4% as heavy fraction. The energy balance of this SRF production process showed that of the total input energy content of C&D waste material to MT waste sorting plant, 74% was recovered in the form of SRF, 16% belonged to the reject material and rest 10% belonged to the streams of fine fraction and heavy fraction. From the material balances of this process, mass fractions of plastic (soft), paper and cardboard, wood and plastic (hard) recovered in the SRF stream were 84%, 82%, 72% and 68% respectively of their input masses to MT plant. A high mass fraction of plastic (PVC) and rubber material was found in the reject material

  11. Measurements Of The Top Quark-anti-top Quark Production Cross Section At Center Of Mass Energy = Tev And Top Mass In The Dielectron Channel

    CERN Document Server

    Kozminski, J

    2005-01-01

    The first measurement of the top-antitop production cross section in proton-antiproton collisions at s = 1.96 TeV using 243 pb−1 of data collected with the DØ detector at Fermilab is presented. In this analysis, only the dielectron final state is considered. Five events are observed, and 0.93 background events are expected. The measured cross section, after accounting for the expected branching ratio to the dielectron channel, is: stt&d1;=14.9 +9.4-1.8st at+2.5-1.8 syst±1.0 lumi pb, which agrees with the predicted cross section for top quarks with a mass of 175 GeV. In addition, a first-pass at a measurement of the top mass using the neutrino-weighting method is presented. This measurement is also performed in the dielectron channel using the five events observed in the cross section measurement.

  12. Evaluating mass loading products by comparison to GPS array daily solutions

    Science.gov (United States)

    Xu, Chang

    2017-01-01

    We evaluate the benefit of different global geophysical loading products on the internal scatter of GPS position time-series from 240 globally distributed sites. We focus on the non-tidal atmospheric pressure loading predicted from NASA's Modern-Era Retrospective Analysis for Research and Applications (MERRA-NATML) and the European Center for Medium-Range Weather Forecasts operational model (ECMWF-NATML), non-tidal ocean loading predicted from the Ocean Model for Circulation and Tides model (OMCT-NTOL), and the continental water storage loading predicted from the MERRA model (MERRA-CWSL) and the GFZ's Land Surface Discharge Model (LSDM-CWSL), respectively. The result shows that the root mean square (RMS) discrepancy of different CWSL models is larger than that of NATML models in the vertical component due to the varying model parameters and input data choices. We discuss the performance of different loading models and their combination to reduce the weighted RMS of GPS up-coordinates. MERRA-NATML & OMCT-NTOL & MERRA-CWSL reduced the weighted RMS (WRMS) in 96 per cent (JPL solutions) and 86 per cent (SOPAC solutions) of the cases, and ECMWF-NATML & OMCT-NTOL & LSDM-CWSL reduced the WRMS in 95 per cent (JPL solutions) and 88 per cent (SOPAC solutions) of the cases. The result shows that local effects and technical uncertainties in GPS time-series hamper the meaningful comparison between GPS observations and mass loading models. Hence, simply using the RMS of the time-series as the assessment criteria may lead to biased comparison results. Nonetheless, we give a detailed comparison (differences in phase and amplitude at seasonal timescales) for eight representative stations located adjacent to great rivers, lakes and reservoirs. We find that LSDM can provide a complementary model to study the small-scale hydrological loading like loading extremes along river channels. However, such small-scale hydrological loading effects are still instable to be modelled in some

  13. Identification of multiple serine to asparagine sequence variation sites in an intended copy product of LUCENTIS® by mass spectrometry.

    Science.gov (United States)

    Griaud, François; Winter, Andrej; Denefeld, Blandine; Lang, Manuel; Hensinger, Héloïse; Straube, Frank; Sackewitz, Mirko; Berg, Matthias

    2017-08-28

    Patent expiration of first-generation biological and the high cost of innovative biological are 2 drivers for the development of biosimilar products. There are, however, technical challenges to the production of exact copies of such large molecules. In this study, we performed a head-to-head comparison between the originator anti-VEGF-A Fab product LUCENTIS® (ranibizumab) and an intended copy product using an integrated analytical approach. While no differences could be observed using size-exclusion chromatography, capillary electrophoresis-sodium dodecyl sulfate and potency assays, different acidic peaks were identified with cation ion exchange chromatography and capillary zone electrophoresis. Further investigation of the intact Fab, subunits and primary sequence with mass spectrometry demonstrated the presence of a modified light chain variant in the intended copy product batches. This variant was characterized with a mass increase of 27.01 Da compared with the originator sequence and its abundance was estimated in the range of 6-9% of the intended copy product light chain. MS/MS spectra interrogation confirmed that this modification relates to a serine to asparagine sequence variant found in the intended copy product light chain. We demonstrated that the integration of high-resolution and sensitive orthogonal technologies was beneficial to assess the similarity of an originator and an intended copy product.

  14. Isobaric production cross sections from 0.6 GeV proton irradiation of neptunium and thorium using mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Wenger, H.U. [Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland)]. E-mail: hansueli.wenger@psi.ch; Al Mazouzi, A. [Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Atchison, F. [Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Burghartz, M. [Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Chawla, R. [Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Ecole Polytechnique Federale de Lausanne, CH-1015 Lausanne (Switzerland); Guenther-Leopold, I. [Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Heimgartner, P. [Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Hellwig, Ch. [Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Ingold, F. [Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Kopajtic, Z. [Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Linder, H.P. [Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland)

    2006-01-09

    A high-fluence proton irradiation of neptunium was the last experiment in PSIs programme ATHENA related to accelerator-based transmutation. The principal aim of the programme has been to provide experimental data for the validation of theoretical models in nucleon-meson transport codes, with emphasis on the mass yield distribution of fission and spallation products. An improved mass spectrometry method has allowed the direct derivation of isobaric production cross sections with only minor corrections and an estimate of the fission cross section by integration in the fission hump. In a second sample position of the irradiation head, a repetition of the previous ATHENA experiment with thorium was possible, profiting from the improved mass spectrometry technique. The experimental results are better predicted by the code FUSSPOT than by HETC/RAL, both used at PSI.

  15. Subjective Norms as a Driver of Mass Communication Students' Intentions to Adopt New Media Production Technologies

    Science.gov (United States)

    Hopp, Toby M.

    2013-01-01

    In this study, the impact of subjective norms on mass communication students' intentions to adopt new media production technologies was explored. The results indicated that subjective norms play an instrumental role in explaining behavioral intentions to adopt new media technologies. Moreover, the data indicated that public relations students…

  16. Accurate quantitation of pentaerythritol tetranitrate and its degradation products using liquid chromatography-atmospheric pressure chemical ionization-mass spectrometry

    NARCIS (Netherlands)

    Brust, H.; Asten, A. van; Koeberg, M.; Dalmolen, J.; Heijden, A.E.D.M. van der; Schoenmakers, P.

    2014-01-01

    After an explosion of pentaerythritol tetranitrate (PETN), its degradation products pentaerythritol trinitrate (PETriN), dinitrate (PEDiN) and mononitrate (PEMN) were detected using liquid chromatography-atmospheric-pressure chemical-ionization-mass spectrometry (LC-APCI-MS). Discrimination between

  17. Subjective Norms as a Driver of Mass Communication Students' Intentions to Adopt New Media Production Technologies

    Science.gov (United States)

    Hopp, Toby M.

    2013-01-01

    In this study, the impact of subjective norms on mass communication students' intentions to adopt new media production technologies was explored. The results indicated that subjective norms play an instrumental role in explaining behavioral intentions to adopt new media technologies. Moreover, the data indicated that public relations students…

  18. Auditory presentation at test does not diminish the production effect in recognition.

    Science.gov (United States)

    Forrin, Noah D; MacLeod, Colin M

    2016-06-01

    Three experiments investigated whether auditory information at test would undermine the relational distinctiveness of vocal production at study, diminishing the production effect. In Experiment 1, with visual presentation during study, the production effect was equivalently large regardless of whether participants read each test word out loud prior to making their recognition decision. In Experiment 2, incorporating auditory presentation during study, the production effect was unaltered by whether recognition test words were presented visually or auditorily. In Experiment 3, the authors manipulated whether presentation was visual or auditory both at study and at test. Once again, presentation modality at test did not affect the size of the production effect, although the effect was significantly smaller when words were presented auditorily at study. These experiments demonstrate that production at the time of study stands out as distinct above and beyond auditory information. Moreover, this distinct aloud information need not "stand out" against a background of silent unstudied words on a recognition test. Consistent with the distinctiveness account, encoding via production enhances later recognition consistently, regardless of study or test modality. (PsycINFO Database Record

  19. Testing neutrino mass generation mechanisms from the lepton flavor violating decay of the Higgs boson

    Science.gov (United States)

    Aoki, Mayumi; Kanemura, Shinya; Sakurai, Kodai; Sugiyama, Hiroaki

    2016-12-01

    We investigate how observations of the lepton flavor violating decay of the Higgs boson (h → ℓℓ‧) can narrow down models of neutrino mass generation mechanisms, which were systematically studied in Refs. [1,2] by focusing on the combination of new Yukawa coupling matrices with leptons. We find that a wide class of models for neutrino masses can be excluded if evidence for h → ℓℓ‧ is really obtained in the current or future collider experiments. In particular, simple models of Majorana neutrino masses cannot be compatible with the observation of h → ℓℓ‧. It is also found that some of the simple models to generate masses of Dirac neutrinos radiatively can be compatible with a significant rate of the h → ℓℓ‧ process.

  20. Testing neutrino mass generation mechanisms from the lepton flavor violating decay of the Higgs boson

    CERN Document Server

    Aoki, Mayumi; Sakurai, Kodai; Sugiyama, Hiroaki

    2016-01-01

    We investigate how observations of the lepton flavor violating decay of the Higgs boson ($h \\to \\ell\\ell^\\prime$) can narrow down models of neutrino mass generation mechanisms, which were systematically studied in Refs. [1,2] by focusing on the combination of new Yukawa coupling matrices with leptons. We find that a wide class of models for neutrino masses can be excluded if evidence for $h \\to \\ell\\ell^\\prime$ is really obtained in the current or future collider experiments. In particular, simple models of Majorana neutrino masses cannot be compatible with the observation of $h \\to \\ell\\ell^\\prime$. It is also found that some of the simple models to generate masses of Dirac neutrinos radiatively can be compatible with a significant rate of the $h \\to \\ell\\ell^\\prime$ process.