Effects of Different Types of Clays and Maleic Anhydride Modified Polystyrene on Polystyrene/Clay Nanocomposites

Directory of Open Access Journals (Sweden)

M. Mehrabzadeh

2013-01-01

Full Text Available Polymer/clay nanocomposites are considered as a new subject of research in Iran and the world. Addition of a minimum amount of clay (2-5wt% can improve the mechanical properties, enhance barrier properties and reduce flammability dramatically. Polystyrene (PS exhibits high strength, high modulus and excellent dimensional stability, but it has poor ductility, elongation, and flexural modulus. By incorporating clay into polystyrene these properties can be improved. In this study preparation of polystyrene/clay nanocomposite, effects of different types of clays (Cloisite 10A andNanomer I.30TC and maleic anhydride modified polystyrene on mechanical properties of the prepared polystyrene/clay nanocomposites were evaluated. Samples were prepared by a twin screw extruder. Transmission electron microscopy (TEM and X-ray diffraction (XRD techniques were employed to evaluate the extent of intercalation and exfoliation of silicate layers in the nanocomposites. Mechanical tests show that by addition of clay and maleic anhydride modified polystyrene the flexural modulus (~30% and elongation-at-break (~40% of prepared nanocomposites have been improved. XRD and TEM results show that nanocomposite have an intercalated structure with ability to change to further exfoliation structure.

Solid polystyrene and deuterated polystyrene light output response to fast neutrons

International Nuclear Information System (INIS)

Simpson, R.; Danly, C.; Merrill, F. E.; Volegov, P. L.; Wilde, C.; Glebov, V. Yu.; Hurlbut, C.

2016-01-01

The Neutron Imaging System has proven to be an important diagnostic in studying DT implosion characteristics at the National Ignition Facility. The current system depends on a polystyrene scintillating fiber array, which detects fusion neutrons born in the DT hotspot as well as neutrons that have scattered to lower energies in the surrounding cold fuel. Increasing neutron yields at NIF, as well as a desire to resolve three-dimensional information about the fuel assembly, have provided the impetus to build and install two additional next-generation neutron imaging systems. We are currently investigating a novel neutron imaging system that will utilize a deuterated polystyrene (CD) fiber array instead of standard hydrogen-based polystyrene (CH). Studies of deuterated xylene or deuterated benzene liquid scintillator show an improvement in imaging resolution by a factor of two [L. Disdier et al., Rev. Sci. Instrum. 75, 2134 (2004)], but also a reduction in light output [V. Bildstein et al., Nucl. Instrum. Methods Phys. Res., Sect. A 729, 188 (2013); M. I. Ojaruega, Ph.D. thesis, University of Michigan, 2009; M. T. Febbraro, Ph.D. thesis, University of Michigan, 2014] as compared to standard plastic. Tests of the relative light output of deuterated polystyrene and standard polystyrene were completed using 14 MeV fusion neutrons generated through implosions of deuterium-tritium filled capsules at the OMEGA laser facility. In addition, we collected data of the relative response of these two scintillators to a wide energy range of neutrons (1-800 MeV) at the Weapons Neutrons Research Facility. Results of these measurements are presented.

Solid polystyrene and deuterated polystyrene light output response to fast neutrons

Energy Technology Data Exchange (ETDEWEB)

Simpson, R., E-mail: raspberry@lanl.gov; Danly, C.; Merrill, F. E.; Volegov, P. L.; Wilde, C. [Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Glebov, V. Yu. [Laboratory for Laser Energetics, Rochester, New York 14623 (United States); Hurlbut, C. [Eljen Technology, Sweetwater, Texas 79556 (United States)

2016-04-15

The Neutron Imaging System has proven to be an important diagnostic in studying DT implosion characteristics at the National Ignition Facility. The current system depends on a polystyrene scintillating fiber array, which detects fusion neutrons born in the DT hotspot as well as neutrons that have scattered to lower energies in the surrounding cold fuel. Increasing neutron yields at NIF, as well as a desire to resolve three-dimensional information about the fuel assembly, have provided the impetus to build and install two additional next-generation neutron imaging systems. We are currently investigating a novel neutron imaging system that will utilize a deuterated polystyrene (CD) fiber array instead of standard hydrogen-based polystyrene (CH). Studies of deuterated xylene or deuterated benzene liquid scintillator show an improvement in imaging resolution by a factor of two [L. Disdier et al., Rev. Sci. Instrum. 75, 2134 (2004)], but also a reduction in light output [V. Bildstein et al., Nucl. Instrum. Methods Phys. Res., Sect. A 729, 188 (2013); M. I. Ojaruega, Ph.D. thesis, University of Michigan, 2009; M. T. Febbraro, Ph.D. thesis, University of Michigan, 2014] as compared to standard plastic. Tests of the relative light output of deuterated polystyrene and standard polystyrene were completed using 14 MeV fusion neutrons generated through implosions of deuterium-tritium filled capsules at the OMEGA laser facility. In addition, we collected data of the relative response of these two scintillators to a wide energy range of neutrons (1-800 MeV) at the Weapons Neutrons Research Facility. Results of these measurements are presented.

On the Mass Distribution of Stellar-Mass Black Holes

Directory of Open Access Journals (Sweden)

Malkov O. Yu.

2014-12-01

Full Text Available The observational stellar-mass black hole mass distribution exhibits a maximum at about 8 M⊙. It can be explained via the details of the massive star evolution, supernova explosions, or consequent black hole evolution. We propose another explanation, connected with an underestimated influence of the relation between the initial stellar mass and the compact remnant mass. We show that an unimodal observational mass distribution of black holes can be produced by a power-law initial mass function and a monotonic “remnant mass versus initial mass” relation.

The neutron star mass distribution

Energy Technology Data Exchange (ETDEWEB)

Kiziltan, Bülent [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street, Cambridge, MA 02138 (United States); Kottas, Athanasios; De Yoreo, Maria [Department of Applied Mathematics and Statistics, University of California, Santa Cruz, CA 95064 (United States); Thorsett, Stephen E., E-mail: bkiziltan@cfa.harvard.edu [Department of Astronomy and Astrophysics, University of California and UCO/Lick Observatory, Santa Cruz, CA 95064 (United States)

2013-11-20

In recent years, the number of pulsars with secure mass measurements has increased to a level that allows us to probe the underlying neutron star (NS) mass distribution in detail. We critically review the radio pulsar mass measurements. For the first time, we are able to analyze a sizable population of NSs with a flexible modeling approach that can effectively accommodate a skewed underlying distribution and asymmetric measurement errors. We find that NSs that have evolved through different evolutionary paths reflect distinctive signatures through dissimilar distribution peak and mass cutoff values. NSs in double NS and NS-white dwarf (WD) systems show consistent respective peaks at 1.33 M {sub ☉} and 1.55 M {sub ☉}, suggesting significant mass accretion (Δm ≈ 0.22 M {sub ☉}) has occurred during the spin-up phase. The width of the mass distribution implied by double NS systems is indicative of a tight initial mass function while the inferred mass range is significantly wider for NSs that have gone through recycling. We find a mass cutoff at ∼2.1 M {sub ☉} for NSs with WD companions, which establishes a firm lower bound for the maximum NS mass. This rules out the majority of strange quark and soft equation of state models as viable configurations for NS matter. The lack of truncation close to the maximum mass cutoff along with the skewed nature of the inferred mass distribution both enforce the suggestion that the 2.1 M {sub ☉} limit is set by evolutionary constraints rather than nuclear physics or general relativity, and the existence of rare supermassive NSs is possible.

Synthesis and Linear Viscoelasticity of Polystyrene Stars with a Polyketone Core

NARCIS (Netherlands)

Polgar, L. M.; Lentzakis, H.; Collias, D.; Snijkers, F.; Lee, S.; Chang, T.; Sakellariou, G.; Wever, D. A. Z.; Toncelli, C.; Broekhuis, A. A.; Picchioni, F.; Gotsis, A. D.; Vlassopoulos, D.

2015-01-01

We report on a novel synthetic route to synthesize relatively large quantities of polystyrene (PS) star polymers with targeted arm functionality and molar mass and their theological properties in the molten state. The synthetic route involves grafting styrene monomers onto a modified (aliphatic,

Simulative calculation of bromo-polystyrene mechanical properties

CERN Document Server

Wang Chao; Tang Yong Jian

2002-01-01

The non-crystal model of polystyrene and bromo-polystyrene was established with the help of simulative software in the computer. DREIDING was chosen as force field and its parameters is modified according to the published data. Based on the calculation results and other published data the mechanism properties of polystyrene and bromo-polystyrene, such as bulk module, Yong's module and Poisson's ratios, were discussed

ON THE MASS DISTRIBUTION AND BIRTH MASSES OF NEUTRON STARS

International Nuclear Information System (INIS)

Özel, Feryal; Psaltis, Dimitrios; Santos Villarreal, Antonio; Narayan, Ramesh

2012-01-01

We investigate the distribution of neutron star masses in different populations of binaries, employing Bayesian statistical techniques. In particular, we explore the differences in neutron star masses between sources that have experienced distinct evolutionary paths and accretion episodes. We find that the distribution of neutron star masses in non-recycled eclipsing high-mass binaries as well as of slow pulsars, which are all believed to be near their birth masses, has a mean of 1.28 M ☉ and a dispersion of 0.24 M ☉ . These values are consistent with expectations for neutron star formation in core-collapse supernovae. On the other hand, double neutron stars, which are also believed to be near their birth masses, have a much narrower mass distribution, peaking at 1.33 M ☉ , but with a dispersion of only 0.05 M ☉ . Such a small dispersion cannot easily be understood and perhaps points to a particular and rare formation channel. The mass distribution of neutron stars that have been recycled has a mean of 1.48 M ☉ and a dispersion of 0.2 M ☉ , consistent with the expectation that they have experienced extended mass accretion episodes. The fact that only a very small fraction of recycled neutron stars in the inferred distribution have masses that exceed ∼2 M ☉ suggests that only a few of these neutron stars cross the mass threshold to form low-mass black holes.

Renewable aromatics from the degradation of polystyrene under mild conditions

Directory of Open Access Journals (Sweden)

Nouf M. Aljabri

2017-12-01

Full Text Available A bimetallic FeCu/alumina catalyst was prepared and characterized. It showed excellent catalytic activity to quantitatively convert polystyrene (PS into aromatics at low temperatures. A clear goldish yellow liquid was produced at 250 °C in a batch reactor without distillation. A liquid yield of 66% in an inert environment was achieved without the formation of coke and gas by-products. An exposure time of 90 min. and a catalyst loading of 200 mg were considered as an optimum conditions to minimize the styrene re-polymerization. The gas chromatography/mass spectrometry (GC/MS analysis confirms that the primary products are styrene, ethylbenzene, cumene, toluene and α-methylstyrene. Keywords: Polystyrene, Bimetallic, Low-temperature, Catalytic degradation

Effect of Recycling in Post-Consumer Polystyrene Cups

OpenAIRE

Ahmed, Mehnaz

2016-01-01

The aim of the thesis was to recycle post-consumer polystyrene cups and to analyze the changes in mechanical and rheological properties of the recycled polystyrene. The me-chanical properties were tensile strength, Young’s modulus and the rheological proper-ties was melt flow index. In order to analyze the changes in properties, material testing results of pristine polystyrene were compared with the recycled polystyrene. The same polystyrene material was recycled and tested twice in order to ...

Simple Coatings to Render Polystyrene Protein Resistant

Directory of Open Access Journals (Sweden)

Marcelle Hecker

2018-02-01

Full Text Available Non-specific protein adsorption is detrimental to the performance of many biomedical devices. Polystyrene is a commonly used material in devices and thin films. Simple reliable surface modification of polystyrene to render it protein resistant is desired in particular for device fabrication and orthogonal functionalisation schemes. This report details modifications carried out on a polystyrene surface to prevent protein adsorption. The trialed surfaces included Pluronic F127 and PLL-g-PEG, adsorbed on polystyrene, using a polydopamine-assisted approach. Quartz crystal microbalance with dissipation (QCM-D results showed only short-term anti-fouling success of the polystyrene surface modified with F127, and the subsequent failure of the polydopamine intermediary layer in improving its stability. In stark contrast, QCM-D analysis proved the success of the polydopamine assisted PLL-g-PEG coating in preventing bovine serum albumin adsorption. This modified surface is equally as protein-rejecting after 24 h in buffer, and thus a promising simple coating for long term protein rejection of polystyrene.

THE MASS DISTRIBUTION OF COMPANIONS TO LOW-MASS WHITE DWARFS

International Nuclear Information System (INIS)

Andrews, Jeff J.; Price-Whelan, Adrian M.; Agüeros, Marcel A.

2014-01-01

Measuring the masses of companions to single-line spectroscopic binary stars is (in general) not possible because of the unknown orbital plane inclination. Even when the mass of the visible star can be measured, only a lower limit can be placed on the mass of the unseen companion. However, since these inclination angles should be isotropically distributed, for a large enough, unbiased sample, the companion mass distribution can be deconvolved from the distribution of observables. In this work, we construct a hierarchical probabilistic model to infer properties of unseen companion stars given observations of the orbital period and projected radial velocity of the primary star. We apply this model to three mock samples of low-mass white dwarfs (LMWDs; M ≲ 0.45 M ☉ ) and a sample of post-common-envelope binaries. We use a mixture of two Gaussians to model the WD and neutron star (NS) companion mass distributions. Our model successfully recovers the initial parameters of these test data sets. We then apply our model to 55 WDs in the extremely low-mass (ELM) WD Survey. Our maximum a posteriori model for the WD companion population has a mean mass μ WD = 0.74 M ☉ , with a standard deviation σ WD = 0.24 M ☉ . Our model constrains the NS companion fraction f NS to be <16% at 68% confidence. We make samples from the posterior distribution publicly available so that future observational efforts may compute the NS probability for newly discovered LMWDs

THE MASS DISTRIBUTION OF COMPANIONS TO LOW-MASS WHITE DWARFS

Energy Technology Data Exchange (ETDEWEB)

Andrews, Jeff J.; Price-Whelan, Adrian M.; Agüeros, Marcel A. [Department of Astronomy, Columbia University, 550 W 120th Street, New York, NY 10027 (United States)

2014-12-20

Measuring the masses of companions to single-line spectroscopic binary stars is (in general) not possible because of the unknown orbital plane inclination. Even when the mass of the visible star can be measured, only a lower limit can be placed on the mass of the unseen companion. However, since these inclination angles should be isotropically distributed, for a large enough, unbiased sample, the companion mass distribution can be deconvolved from the distribution of observables. In this work, we construct a hierarchical probabilistic model to infer properties of unseen companion stars given observations of the orbital period and projected radial velocity of the primary star. We apply this model to three mock samples of low-mass white dwarfs (LMWDs; M ≲ 0.45 M {sub ☉}) and a sample of post-common-envelope binaries. We use a mixture of two Gaussians to model the WD and neutron star (NS) companion mass distributions. Our model successfully recovers the initial parameters of these test data sets. We then apply our model to 55 WDs in the extremely low-mass (ELM) WD Survey. Our maximum a posteriori model for the WD companion population has a mean mass μ{sub WD} = 0.74 M {sub ☉}, with a standard deviation σ{sub WD} = 0.24 M {sub ☉}. Our model constrains the NS companion fraction f {sub NS} to be <16% at 68% confidence. We make samples from the posterior distribution publicly available so that future observational efforts may compute the NS probability for newly discovered LMWDs.

Polystyrene/Hyperbranched Polyester Blends and Reactive Polystyrene/Hyperbranched Polyester Blends

National Research Council Canada - National Science Library

Mulkern, Thomas

1999-01-01

.... In this work, the incorporation of HBPs in thermoplastic blends was investigated. Several volume fractions of hydroxyl functionalized hyperbranched polyesters were melt blended with nonreactive polystyrene (PS...

''Nonisolated-sensor'' solid polystyrene absorbed dose measurements

International Nuclear Information System (INIS)

Zeitz, L.; Laughlin, J.S.

1982-01-01

A ''nonisolated-sensor'' solid polystyrene calorimeter was constructed to test the role of thermal diffusion in limiting the length of irradiation time during which temperature measurements with nonisolated sensors could be made sufficiently free of drift for determining dose with radiation fields such as gamma rays, x rays, and high-energy electrons. From measured ratios of dose at 5.0 and 0.5 cm in polystyrene and comparisons to dose measurements with a polystyrene parallel-plate (pancake) ion chamber, it was shown that thermal diffusion is sufficiently small in polystyrene to permit accurate measurements for irradiation periods of less than 20 min. Comparison of the absorbed dose measurements and depth dose ratios with pancake ion chambers and calorimeter showed, that within the precision and accuracy of the two measuring systems, there is close agreement. The nonisolated-sensor solid polystyrene calorimeter has the interesting features of (i) simplicity of construction, (ii) simplicity of operation without vacuum or feedback for temperature control, (iii) capability of simultaneous measurements at several depths and off-axis positions, (iv) the very small thermal defect correction with polystyrene, and (v) operation with the calorimeter in any orientation

Nonisolated-sensor solid polystyrene absorbed dose measurements

International Nuclear Information System (INIS)

Zeitz, L.; Laughlin, J.S.

1982-01-01

A nonisolated-sensor solid polystyrene calorimeter was constructed to test the role of thermal diffusion in limiting the length of irradiation time during which temperature measurements with nonisolated sensors could be made sufficiently free of drift for determining dose with radiation fields such as gamma rays, x rays, and high-energy electrons. From measured ratios of dose at 5.0 and 0.5 cm in polystyrene and comparisons to dose measurements with a polystyrene parallel-plate (pancake) ion chamber, it was shown that thermal diffusion is sufficiently small in polystyrene to permit accurate measurements for irradiation periods of less than 20 min. Comparison of the absorbed dose measurements and depth dose ratios with pancake ion chambers and calorimeter showed, that within the precision and accuracy of the two measuring systems, there is close agreement. The nonisolated-sensor solid polystyrene calorimeter has the interesting features of (i) simplicity of construction, (ii) simplicity of operation without vacuum or feedback for temperature control, (iii) capability of simultaneous measurements at several depths and off-axis positions, (iv) the very small thermal defect correction with polystyrene, and (v) operation with the calorimeter in any orientation

Site-specific fragmentation of polystyrene molecule using size-selected Ar gas cluster ion beam

International Nuclear Information System (INIS)

Moritani, Kousuke; Mukai, Gen; Hashinokuchi, Michihiro; Mochiji, Kozo

2009-01-01

The secondary ion mass spectrum (SIMS) of a polystyrene thin film was investigated using a size-selected Ar gas cluster ion beam (GCIB). The fragmentation in the SIM spectrum varied by kinetic energy per atom (E atom ); the E atom dependence of the secondary ion intensity of the fragment species of polystyrene can be essentially classified into three types based on the relationship between E atom and the dissociation energy of a specific bonding site in the molecule. These results indicate that adjusting E atom of size-selected GCIB may realize site-specific bond breaking within a molecule. (author)

Thermo-mechanical characterization of a monochlorophenyl, hepta isobutyl polyhedral oligomeric silsesquioxane/polystyrene composite

International Nuclear Information System (INIS)

Blanco, Ignazio; Bottino, Francesco A.; Cicala, Gianluca; Cozzo, Giulia; Latteri, Alberta; Recca, Antonino

2014-01-01

The thermal and mechanical properties of a monochlorophenyl, hepta isobutyl Polyhedral Oligomeric Silsesquioxane/Polystyrene (ph,hib-POSS/PS) composite were studied and compared with those of pristine polymer. ph,hib-POSS/PS system was prepared by solubilization and precipitation of Polystyrene (PS) in the presence of POSS. Scanning Electron Microscopy (SEM) was performed to check the distribution of the filler in the polymer matrix. Dynamic Mechanical Analysis (DMA) was carried out to measure viscoelastic properties of solid samples. Degradations were carried out into a thermobalance and the obtained thermogravimetric (TG) and differential thermogravimetric (DTG) curves were discussed and interpreted

Biodegradation of starch–graft–polystyrene and starch–graft–poly(methacrylic acid copolymers in model river water

Directory of Open Access Journals (Sweden)

Nikolić Vladimir

2013-01-01

Full Text Available In this paper the biodegradation study of grafted copolymers of polystyrene (PS and corn starch and poly(methacrylic acid and corn starch in model river water is described. These copolymers were obtained in the presence of different amine activators. The synthesized copolymers and products of degradation were characterized by Fourier Transform Infrared Spectroscopy (FTIR and Scanning Electron Microscopy (SEM. Biodegradation was monitored by mass decrease and number of microorganisms by Koch’s method. Biodegradation of both copolymers advanced with time, poly(methacrylic acid-graft-starch copolymers completely degraded after 21 day, and polystyrene-graft-starch partially degraded (45.78-93.09 % of total mass after 27 days. Differences in the degree of biodegradation are consequences of different structure of the samples, and there is a significant negative correlation between the share of polystyrene in copolymer and degree of biodegradation. The grafting degree of PS necessary to prevent biodegradation was 54 %. Based on experimental evidence, mechanisms of both biodegradation processes are proposed, and influence of degree of starch and synthetic component of copolymers on degradation were established. [Projekat Ministarstva nauke Republike Srbije, br. 172001 i br. 172062

Mass distributions in disk galaxies

NARCIS (Netherlands)

Martinsson, Thomas; Verheijen, Marc; Bershady, Matthew; Westfall, Kyle; Andersen, David; Swaters, Rob

We present results on luminous and dark matter mass distributions in disk galaxies from the DiskMass Survey. As expected for normal disk galaxies, stars dominate the baryonic mass budget in the inner region of the disk; however, at about four optical scale lengths (hR ) the atomic gas starts to

On the Mass Distribution of Animal Species

Science.gov (United States)

Redner, Sidney; Clauset, Aaron; Schwab, David

2009-03-01

We develop a simple diffusion-reaction model to account for the broad and asymmetric distribution of adult body masses for species within related taxonomic groups. The model assumes three basic evolutionary features that control body mass: (i) a fixed lower limit that is set by metabolic constraints, (ii) a species extinction risk that is a weakly increasing function of body mass, and (iii) cladogenetic diffusion, in which daughter species have a slight tendency toward larger mass. The steady-state solution for the distribution of species masses in this model can be expressed in terms of the Airy function. This solution gives mass distributions that are in good agreement with data on 4002 terrestrial mammal species from the late Quaternary and 8617 extant bird species.

Activity of Antimicrobial Silver Polystyrene Nanocomposites

Directory of Open Access Journals (Sweden)

M. Palomba

2012-01-01

Full Text Available A simple technique based on doping polymers with in situ generated silver nanoparticles (Ag/PS films has been developed. In particular, an antiseptic material has been prepared by dissolving silver 1,5-cyclooctadiene-hexafluoroacetylacetonate in amorphous polystyrene, and the obtained solid solution has been heated for ca. 10 s at a convenient temperature (180°C. Under such conditions the metal precursor decomposes producing silver atoms that diffuse into the polymer and clusterize. The antimicrobial characteristics of the resulting polystyrene-based material have been accurately evaluated toward Escherichia coli (E. coli comparing the cytotoxicity effect of 10 wt.% and 30 wt.% (drastic and mild annealing silver-doped polystyrene to the corresponding pure micrometric silver powder. Two different bacterial viability assays were performed in order to demonstrate the cytotoxic effect of Ag/PS films on cultured E. coli: (1 turbidimetric determination of optical density; (2 BacLight fluorescence-based test. Both methods have shown that silver-doped polystyrene (30 wt.% provides higher antibacterial activity than pure Ag powder, under similar concentration and incubation conditions.

A constitutive analysis of transient and steady-state elongational viscosities of bidisperse polystyrene blends

DEFF Research Database (Denmark)

Wagner, Manfred H.; Rolon-Garrido, Victor H.; Nielsen, Jens Kromann

2008-01-01

The transient and steady-state elongational viscosity data of three bidisperse polystyrene blends were investigated recently by Nielsen et al. [J. Rheol. 50, 453-476 (2006)]. The blends contain a monodisperse high molar mass component (M-L= 390 kg/ mol) in a matrix of a monodisperse small molar m...

A proton-conducting composite membrane: Sn0.95Al0.05P2O7 and polystyrene-b-poly(ethylene/propylene)-b-polystyrene

International Nuclear Information System (INIS)

Jin, Yongcheng; Hibino, Takashi

2010-01-01

An anhydrous proton conductor, Sn 0.95 Al 0.05 P 2 O 7 (SAPO), composed of polystyrene-b-poly(ethylene/propylene)-b-polystyrene (SEPS), was developed and characterized using morphological, structural, and electrochemical analyses. In the composite membrane with 20 wt% SEPS, a homogeneous distribution of SAPO particles in the matrix was obtained in the thickness range of 65-90 μm, yielding a proton conductivity of 3.4 x 10 -3 S cm -1 at 200 o C, tensile strength of 4.6 MPa and an elongation at break of 711.0% at room temperature. Fuel cell tests verified that the open-circuit voltage was maintained at a constant value of approximately 1 V between 100 and 250 o C. The peak power densities achieved with unhumidified H 2 and air were 77.0 mW cm -2 at 100 o C, 121.0 mW cm -2 at 150 o C, and 163.1 mW cm -2 at 225 o C.

Synthesis of micro-sized polystyrene magnetic particles

International Nuclear Information System (INIS)

Neves, Juliete S.; Suarez, Paulo A.Z.; Umpierre, Alexandre P.; Machado, Fabricio; Souza Junior, Fernando G. de

2011-01-01

The present work illustrates the synthesis of spherical and micro-sized polystyrene magnetic particles by using a water-based suspension polymerization process to incorporate in situ surface modified superparamagnetic Fe 3 O 4 nanoparticles. The crystallite size of Fe 3 O 4 was determined to be equal to 7.7 nm, based on Scherrer's equation and XRD measurement. According to EDX analyses, Fe 3 O 4 / polystyrene nanocomposites particles show strong characteristic peaks Kα and Kβ of iron at the interval from 6.38 KeV to 7.04 KeV with an amount of iron in the samples equal to 98 %, indicating that the inorganic material dispersed in the polystyrene matrix is essentially Fe in the form of iron oxide (Fe 3 O 4 ). The obtained polymeric materials presented good magnetic behavior, indicating that the modified Fe 3 O 4 nanoparticles were successfully dispersed in the polystyrene particles. (author)

Intermediate mass distribution of the dual resonance pomeron

International Nuclear Information System (INIS)

Chiu, C.B.; Matsuda, S.

1978-01-01

The intermediate mass distribution of the dual resonance pomeron is determined at the one-loop level and it is shown that the mass distribution obtained is remarkably similar to a suitably defined mass distribution in the dual multiperipheral model. Thus it is suggestive to identify the intermediate states of the dual resonance pomeron with multiperipheral processes. (Auth.)

Radiosynthesis and in vitro evaluation of the polystyrene particles as a promising probe in biomedical sciences

International Nuclear Information System (INIS)

Chen Jianmin; Tan Mingguang; Wu Yuanfang; Zhang Guilin; Li Yan

2005-01-01

Polystyrene particles with precise monodisperse particle size distributions ranging from 20nm to 90μm is now commercially available and it has very useful and versatile applications in many life sciences research fields. A simple direct labeling method was used to synthesis the iodinated ultrafine polystyrene particles. The assay of X-ray photoelectron spectroscopy(XPS) as well as Fourier Transform Infrared Spectroscopy (FTIR) indicated the formation of stable covalent bond to aryl group of the polymer particles. The purified radiosynthesis product was incubated with serum of rat, and then evaluated by in vitro stability test. The result showed that radioiodinated ultrafine polystyrene particles were largely unmetablized at 2 hours post-exposure, indicating the potential useful application of this widely used polymer particles as a promising probe in biomedical and pharmaceutical sciences.

Technical Note: Effect of Incorporating Expanded Polystyrene ...

African Journals Online (AJOL)

Incorporating expanded polystyrene granules in concrete matrix can produce lightweight polystyrene aggregate concrete of various densities. Workability which is an important property of concrete, aects the rate of placement and the degree of compaction of concrete. Inadequate compaction leads to reduction in both ...

Polystyrene calorimeter for electron beam dose measurements

DEFF Research Database (Denmark)

Miller, A.

1995-01-01

Calorimeters from polystrene have been constructed for dose measurement at 4-10 MeV electron accelerators. These calorimeters have been used successfully for a few years, and polystyrene calorimeters for use at energies down to 1 MeV and being tested. Advantage of polystyrene as the absorbing...

Fabrication of polystyrene porous films with gradient pore structures

International Nuclear Information System (INIS)

Yan Hongwei; Zhang Lin; Li Bo; Yin Qiang

2010-01-01

Silica opals and multilayer heterostructures were fabricated by vertical deposition technique. Polystyrene inverse opals and gradient porous structures were obtained by colloidal templating, in order to control the pore microstructure of polymer porous materials. As shown in the scanning electron microscopy images, the polystyrene porous structures are precise replicas of inverse structures of the original templates. After being infiltrated with the polystyrene, the photonic stop-band position of the opal composite is redshifted compared with the original template, and it is blueshifted after the opal template being removed. The filling ratio of polystyrene was calculated according to the Bragg formula. (authors)

Nano-sized polystyrene affects feeding, behavior and physiology of brine shrimp Artemia franciscana larvae

NARCIS (Netherlands)

Bergami, Elisa; Bocci, Elena; Vannuccini, Maria Luisa; Monopoli, Marco; Salvati, Anna; Dawson, Kenneth A; Corsi, Ilaria

Nano-sized polymers as polystyrene (PS) constitute one of the main challenges for marine ecosystems, since they can distribute along the whole water column affecting planktonic species and consequently disrupting the energy flow of marine ecosystems. Nowadays very little knowledge is available on

Transmission of terahertz radiation by anisotropic MWCNT/polystyrene composite films

Energy Technology Data Exchange (ETDEWEB)

Okotrub, A.V.; Bulusheva, L.G. [Nikolaev Institute of Inorganic Chemistry, SB RAS, 3 Acad. Lavrentiev Ave., 630090 Novosibirsk (Russian Federation); Novosibirsk State Technical University, 20 Karl Marx Ave., 630092 Novosibirsk (Russian Federation); Kubarev, V.V. [Budker Institute of Nuclear Physics, SB RAS, 11 Acad. Lavrentiev Ave., 630090 Novosibirsk (Russian Federation); Novosibirsk State University, 2 Pirogova st., 630090 Novosibirsk (Russian Federation); Kanygin, M.A.; Sedelnikova, O.V. [Nikolaev Institute of Inorganic Chemistry, SB RAS, 3 Acad. Lavrentiev Ave., 630090 Novosibirsk (Russian Federation)

2011-11-15

Anisotropic composite materials have been prepared by repeated forge rolling of polystyrene and carbon nanotubes (CNTs) with length of {proportional_to}65 {mu}m. Transmission spectra of the composites were recorded for two different polarizations of the electric field. Obtained data indicated that the forge rolling resulted in a predominant orientation of CNTs in polymer matrix. Anisotropic response of the composites was measured at 130 {mu}m wavelength on the Novosibirsk terahertz free electron laser and angular dependence of the transmitted light was determined. Absorption spectrum showed no strong resonance features and it was interpreted by CNTs breaking and agglomeration of CNT fragments during the composite fabrication procedure. Based on classical theory of scattering, considered the scatters as electromagnetic antennas, the size distribution of CNTs in composites was found. Anisotropy of terahertz radiation transmitted from MWCNT/polystyrene composite film on the Novosibirsk free electron laser at 130 {mu}m wavelength. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Effect of planar extension on the structure and mechanical properties of polystyrene-poly(ethylene-¤co¤-butylene)-polystyrene triblock copolymers

DEFF Research Database (Denmark)

Daniel, C.; Hamley, I.W.; Mortensen, K.

2000-01-01

Two thermoplastic poly(styrene)-poly(ethylene-co-butylene) -poly(styrene) triblock copolymers containing either spherical or cylindrical poly(styrene) microdomains were pre-oriented through extensional flow. Small angle neutron scattering (SANS) measurements revealed that the pre-oriented triblock...

Synthesis in pilot plant scale and physical properties of sulfonated polystyrene

Directory of Open Access Journals (Sweden)

Martins Cristiane R.

2003-01-01

Full Text Available The homogenous sulfonation of polystyrene was developed in a pilot plant scale producing polymers with different sulfonation degrees (18 to 22 mole % of sulfonated styrene units. The reaction yield depends chiefly on the concentration ratio of acetyl sulfate and polystyrene. The morphological and thermal properties of the sulfonated polystyrene obtained by homogeneous sulfonation were studied by means of scanning electron microscopy, differential scanning calorimetry and thermogravimetry. The glass transition temperature of sulfonated polystyrene increases in relation to pure polystyrene and DCp was evaluated in order to confirm the strong interactions among the ~SO3H groups.

Procedure of non-contacting local mass density and mass density distribution measurements

International Nuclear Information System (INIS)

Menzel, M.; Winkler, K.

1985-01-01

The invention has been aimed at a procedure of non-contacting local mass density and/or mass density distribution measurements i.e. without the interfering influence of sensors or probes. It can be applied to installations, apparatuses and pipings of chemical engineering, to tank constructions and transportation on extreme temperature and/or pressure conditions and aggressive media influences respectively. The procedure has utilized an ionizing quantum radiation whereby its unknown weakening and scattering is compensated by a suitable combination of scattering and transmission counter rate measurements in such a way that the local mass densities and the mass density distribution respectively are determinable

ESR studies of the radiation effects on polystyrene

International Nuclear Information System (INIS)

Garrett, R.W.; O'Donnell, J.H.; Pomery, P.J.

1976-01-01

The aim of this work was to investigate the polystyrene system (both pure and commercial samples) to elucidate the type and percentage of each paramagnetic species upon exposure to various irradiation doses. The size of dose plays a vital role in the type of spectra obtained. Upon irradiation in vacuo, polystyrene displays ESR spectra which are basically triplet in character but the line spacing and intensities of components are observed to depend on the magnitude of the irradiation dose. G value for the total radicals present and for the individual species present as a function of dose have been obtained. The relative concentration of each paramagnetic species has been determined through computer simulation of the observed ESR spectra. The relative stability of the different species with respect to temperature is discussed. The results for deuterated polystyrene is used to support those obtained for the unsubstituted polystyrene system. (author)

Pore Structure and Fluoride Ion Adsorption Characteristics of Zr (IV) Surface-Immobilized Resin Prepared Using Polystyrene as a Porogen

Science.gov (United States)

Mizuki, Hidenobu; Ito, Yudai; Harada, Hisashi; Uezu, Kazuya

Zr(IV) surface-immobilized resins for removal of fluoride ion were prepared by surface template polymerization using polystyrene as a porogen. At polymerization, polystyrene was added in order to increase mesopores (2-50 nm) and macropore (>50 nm) with large macropores (around 300 nm) formed with internal aqueous phase of W⁄O emulsion. The pore structure of Zr(IV) surface-immobilized resins was evaluated by measuring specific surface area, pore volume, and pore size distribution with volumetric adsorption measurement instrument and mercury porosimeter. The adsorption isotherms were well fitted by Langmuir equation. The removal of fluoride was also carried out with column method. Zr(IV) surface-immobilized resins, using 10 g⁄L polystyrene in toluene at polymerization, possessed higher volume of not only mesopores and macropores but also large macropores. Furethermore, by adding the polystyrene with smaller molecular size, the pore volume of mesopores, macropores and large macropores was significantly increased, and the fluoride ion adsorption capacity and the column utilization also increased.

Polystyrene Plastic Waste Conversion into Liquid Fuel with Catalytic Cracking Process Using Al2O3 as Catalyst

Directory of Open Access Journals (Sweden)

Nurul Kholidah

2018-01-01

Full Text Available The increase in energy consumption and an increase in the plastic waste generation are two major problems that arise along with economic growth and the increase in population. Styrofoam is one type of polystyrene plastic waste that can be processed into liquid fuels by cracking process. In this study, the cracking process of polystyrene plastic waste into liquid fuel carried by the catalytic cracking process using Al2O3 as a catalyst. This study aimed to determine the effect of the catalyst weight, length of cracking time and range of temperature in the catalytic cracking process of polystyrene plastic waste into liquid fuel toward the mass and characteristics of liquid fuels produced and to determine the composition of liquid fuels produced. The catalytic cracking process of polystyrene plastic waste with catalyst was done in the fixed bed type reactor by heating the reactor with a heater, where the process took place at temperature of 150°C, 200°C, 250°C and 300°C and the length of the process was varied into 20, 40, and 60 minutes and the catalyst weight was also varied, which were 4%, 6% and 8%, while the styrofoam weight was 250 grams. From the research, the highest mass of liquid fuel derived from polystyrene catalytic cracking process was in the amount of 48.8 grams and liquid yield percentage of 19.5% at temperature of  250°C, cracking time of 60 minutes and weight of 8% catalyst, while the characteristics of liquid fuel that were approaching the characteristics of gasoline was at temperatures of 250°C, cracking time of 60 minutes and weight of 6% catalyst, in which each value of density of 0.763 g/ml, specific gravity of 0.778 and oAPI gravity of 50.2. While other liquid fuels obtained from the cracking of polystyrene were still within the tolerance range characteristic properties of gasoline. Liquid fuels produced from the catalytic cracking process was analyzed using a GC-MS, in which the analysis results indicated that liquid

Elongational viscosity of monodisperse and bidisperse polystyrene melts

DEFF Research Database (Denmark)

Nielsen, Jens Kromann; Rasmussen, Henrik K.; Hassager, Ole

2006-01-01

The start-up and steady uniaxial elongational viscosity have been measured for two monodisperse polystyrene melts with molecular weights of 52 and 103 kg/mole, and for three bidisperse polystyrene melts. The monodisperse melts show a maximum in the steady elongational viscosity vs. the elongational...

Modelling of Convective Process of Water Desorption from Polystyrene

International Nuclear Information System (INIS)

Stakic, M.; Nikolic, A.

2008-01-01

This study presents a mathematical model developed to evaluate the influence of structural and operational factors on convective dehydration process (desorption of liquid phase from capillary-porous material), as well as the possibility to utilize this model for the case of water desorption from polystyrene cation resin CG-8. The model accounts for unsteady one-dimensional simultaneous heat and mass transfer between the gas (air) and the solid phase (resin). The identification of effective transport properties for the considered fixed bed of material (resin CG 8) is discussed. To this purpose available data from the literature are used. (author)

Lipase polystyrene giant amphiphiles.

Science.gov (United States)

Velonia, Kelly; Rowan, Alan E; Nolte, Roeland J M

2002-04-24

A new type of giant amphiphilic molecule has been synthesized by covalently connecting a lipase enzyme headgroup to a maleimide-functionalized polystyrene tail (40 repeat units). The resulting biohybrid forms catalytic micellar rods in water.

THE EFFECTS OF VIEWING ANGLE ON THE MASS DISTRIBUTION OF EXOPLANETS

International Nuclear Information System (INIS)

Lopez, S.; Jenkins, J. S.

2012-01-01

We present a mathematical method to statistically decouple the effects of unknown inclination angles on the mass distribution of exoplanets that have been discovered using radial-velocity (RV) techniques. The method is based on the distribution of the product of two random variables. Thus, if one assumes a true mass distribution, the method makes it possible to recover the observed distribution. We compare our prediction with available RV data. Assuming that the true mass function is described by a power law, the minimum mass function that we recover proves a good fit to the observed distribution at both mass ends. In particular, it provides an alternative explanation for the observed low-mass decline, usually explained as sample incompleteness. In addition, the peak observed near the low-mass end arises naturally in the predicted distribution as a consequence of imposing a low-mass cutoff in the true distribution. If the low-mass bins below 0.02 M J are complete, then the mass distribution in this regime is heavily affected by the small fraction of lowly inclined interlopers that are actually more massive companions. Finally, we also present evidence that the exoplanet mass distribution changes form toward low mass, implying that a single power law may not adequately describe the sample population.

Polystyrene Microbeads by Dispersion Polymerization: Effect of Solvent on Particle Morphology

Directory of Open Access Journals (Sweden)

Lei Jinhua

2014-01-01

Full Text Available Polystyrene microspheres (PS were synthesized by dispersion polymerization in ethanol/2-Methoxyethanol (EtOH/EGME blend solvent using styrene (St as monomer, azobisisobutyronitrile (AIBN as initiator, and PVP (polyvinylpyrrolidone K-30 as stabilizer. The typical recipe of dispersion polymerization is as follows: St/Solvent/AIBN/PVP = 10 g/88 g/0.1 g/2 g. The morphology of polystyrene microspheres was characterized by the scanning electron microscopy (SEM and the molecular weights of PS particles were measured by the Ubbelohde viscometer method. The effect of ethanol content in the blend solvent on the morphology and molecular weight of polystyrene was studied. We found that the size of polystyrene microspheres increased and the molecular weight of polystyrene microspheres decreased with the decreasing of the ethanol content in the blend solvent from 100 wt% to 0 wt%. What is more, the size monodispersity of polystyrene microspheres was quite good when the pure ethanol or pure 2-Methoxyethanol was used; however when the blend ethanol/2-Methoxyethanol solvent was used, the polystyrene microspheres became polydisperse. We further found that the monodispersity of polystyrene microspheres can be significantly improved by adding a small amount of water into the blend solvent; the particles became monodisperse when the content of water in the blend solvent was up to 2 wt%.

Modification of Jute Fibers with Polystyrene via Atom Transfer Radical Polymerization

DEFF Research Database (Denmark)

Plackett, David; Jankova, Katja Atanassova; Egsgaard, Helge

2005-01-01

Atom transfer radical polymerization (ATRP) was investigated as a method of covalently bonding polystyrene to jute (Corchorus capsularis) and as a possible approach to fiber composites with enhanced properties. Jute fibers were modified with a brominated initiator and subsequently ATRP modified...... to attach polystyrene and then examined using SEM, DSC, TGA, FTIR, XPS, elemental analysis, and Py-GC-MS. These techniques confirmed that polystyrene had been covalently bound to the fibers and consequently ATRP-modified jute fiber mats were used to prepare hot-pressed polystyrene composites. Composite...

Comparative characteristics of polystyrene scintillation strips

International Nuclear Information System (INIS)

Gapienko, V.A.; Denisov, A.G.; Mel'nikov, E.A.

1992-01-01

Results are provided for a study of the main characteristics of polystyrene scintillation strips with a cross-section of 200 x 10 mm with two different scintillation-additive compositions: 1.5% p-terphenyl + 0.01% POPOP and 1.5% p-terphenyl + 0.01% DBP. The mean light-attenuation lengths are 180 cm and 260 cm, respectively, for strips with POPOP and DBP. The emittances of the polystyrene scintillators with DBP and POPOP additives have a ratio of 0.8:1.0 as recorded by an FEU-110 photomultiplier. 2 refs., 1 fig., 2 tabs

Local Segmental Dynamics and Stresses in Polystyrene - C$_{60}$ Mixtures

OpenAIRE

Vogiatzis, Georgios G.; Theodorou, Doros N.

2014-01-01

The polymer dynamics of homogeneous C$_{60}$-polystyrene mixtures in the molten state are studied via molecular simulations using two interconnected levels of representation for polystyrene nanocomposites: (a) A coarse-grained representation, in which each polystyrene repeat unit is mapped into a single "superatom" and each fullerene is viewed as a spherical shell. Equilibration of coarse-grained polymer-nanoparticle systems at all length scales is achieved via connectivity-altering Monte Car...

Synthesis of Ag-coated polystyrene colloids by an improved surface seeding and shell growth technique

International Nuclear Information System (INIS)

Tian Chungui; Wang Enbo; Kang Zhenhui; Mao Baodong; Zhang Chao; Lan Yang; Wang Chunlei; Song Yanli

2006-01-01

In this paper, an improved surface seeding and shell growth technique was developed to prepare Ag-polystyrene core shell composite. Polyethyleneimine (PEI) could act as the linker between Ag ions (Ag nanoparticles) and polystyrene (PS) colloids and the reducing agent in the formation of Ag nanoparticles. Due to the multi-functional characteristic of PEI, Ag seeds formed in-situ and were immobilized on the surface of PEI-modified PS colloids and no free Ag clusters coexist with the Ag 'seeding' PS colloids in the system. Then, the additional agents could be added into the resulting dispersions straightly to produce a thick Ag nanoshell. The Ag nanoshell with controllable thickness was formed on the surface of PS by the 'one-pot' surface seeding and shell growth method. The Ag-coverage increased gradually with the increasing of mass ratio of AgNO 3 /PS. The optical properties of the Ag-PS colloids could be tailored by changing the coverage of Ag. - Graphical abstract: An improved surface seeding and shell growth technique was developed to prepare Ag-polystyrene core shell composite. The optical properties of the Ag-PS colloids could be tailored by changing the coverage of Ag. Display Omitted

Invariant mass distributions in cascade decays

International Nuclear Information System (INIS)

Miller, David J.; Osland, Per; Raklev, Are R.

2006-01-01

We derive analytical expressions for the shape of the invariant mass distributions of massless Standard Model endproducts in cascade decays involving massive New Physics (NP) particles, D→Cc→Bbc→Aabc, where the final NP particle A in the cascade is unobserved and where two of the particles a, b, c may be indistinguishable. Knowledge of these expressions can improve the determination of NP parameters at the LHC. The shape formulas are composite, but contain nothing more complicated than logarithms of simple expressions. We study the effects of cuts, final state radiation and detector effects on the distributions through Monte Carlo simulations, using a supersymmetric model as an example. We also consider how one can deal with the width of NP particles and with combinatorics from the misidentification of final state particles. The possible mismeasurements of NP masses through 'feet' in the distributions are discussed. Finally, we demonstrate how the effects of different spin configurations can be included in the distributions

The effectiveness of the biodegradation of raw and processed polystyrene by mealworms

Science.gov (United States)

Leluk, Karol; Hanus-Lorenz, Beata; Rybak, Justyna; Bożek, Magdalena

2017-11-01

In our studies biodegradation of four variants of polystyrene was performed. We tested: raw material (PS), processed polystyrene (PSr), building insulation material (EPS) and food packaging boxes (PSp). Materials were characterized by means melt flow ratio (MFR), shore hardness and gloss. The biochemical assessment of macromolecules (proteins, lipids and sugars) in the mealworms organisms fed with tested forms of polystyrene allowed us to set how efficient and beneficial the biodegradation of types of polystyrene is. We also evaluated the variability of bacterial community in larval guts by the use of denaturing gradient gel electrophoresis (DGGE) on the bacterial DNA of 16S rRNA genes amplified in polymerase chain reaction (PCR). The results suggest that EPS and PSp polystyrene are the most digestible for T. molitor larvae. The metabolic degradation of polystyrene is probably strictly connected with the changes in biodiversity of gut bacteria.

The effectiveness of the biodegradation of raw and processed polystyrene by mealworms

Directory of Open Access Journals (Sweden)

Leluk Karol

2017-01-01

Full Text Available In our studies biodegradation of four variants of polystyrene was performed. We tested: raw material (PS, processed polystyrene (PSr, building insulation material (EPS and food packaging boxes (PSp. Materials were characterized by means melt flow ratio (MFR, shore hardness and gloss. The biochemical assessment of macromolecules (proteins, lipids and sugars in the mealworms organisms fed with tested forms of polystyrene allowed us to set how efficient and beneficial the biodegradation of types of polystyrene is. We also evaluated the variability of bacterial community in larval guts by the use of denaturing gradient gel electrophoresis (DGGE on the bacterial DNA of 16S rRNA genes amplified in polymerase chain reaction (PCR. The results suggest that EPS and PSp polystyrene are the most digestible for T. molitor larvae. The metabolic degradation of polystyrene is probably strictly connected with the changes in biodiversity of gut bacteria.

Field efficacy of expanded polystyrene and shredded waste polystyrene beads for mosquito control in artificial pools and field trials, Islamic Republic of Iran.

Science.gov (United States)

Soltani, A; Vatandoost, H; Jabbari, H; Mesdaghinia, A R; Mahvi, A H; Younesian, M; Hanafi-Bojd, A A; Bozorgzadeh, S

2012-10-01

Concerns about traditional chemical pesticides has led to increasing research into novel mosquito control methods. This study compared the effectiveness of 2 different types of polystyrene beads for control of mosquito larvae in south-east Islamic Republic of Iran. Simulated field trials were done in artificial pools and field trials were carried out in 2 villages in an indigenous malaria area using WHO-recommended methods. Application of expanded polystyrene beads or shredded, waste polystyrene chips to pool surfaces produced a significant difference between pre-treatment and post-treatment density of mosquitoes (86% and 78% reduction respectively 2 weeks after treatment). There was no significant difference between the efficacy of the 2 types of material. The use of polystyrene beads as a component of integrated vector management with other supportive measures could assist in the control of mosquito-borne diseases in the Islamic Republic of Iran and neighbouring countries.

The polymerization of aniline in polystyrene latex particles

Czech Academy of Sciences Publication Activity Database

Blinova, Natalia V.; Reynaud, S.; Roby, F.; Trchová, Miroslava; Stejskal, Jaroslav

2010-01-01

Roč. 160, 15/16 (2010), s. 1598-1602 ISSN 0379-6779 R&D Projects: GA AV ČR IAA400500905; GA ČR GA203/08/0686; GA ČR GA202/09/1626 Institutional research plan: CEZ:AV0Z40500505 Keywords : polyaniline * polystyrene latex * polyaniline-polystyrene composite Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.871, year: 2010

Microstructural study of a nitroxide-mediated poly(ethylene oxide)/polystyrene block copolymer (PEO-b-PS) by electrospray tandem mass spectrometry.

Science.gov (United States)

Girod, Marion; Phan, Trang N T; Charles, Laurence

2008-08-01

Electrospray ionization tandem mass spectrometry has been used to characterize the microstructure of a nitroxide-mediated poly(ethylene oxide)/polystyrene block copolymer, called SG1-capped PEO-b-PS. The main dissociation route of co-oligomers adducted with lithium or silver cation was observed to proceed via the homolytic cleavage of a C-ON bond, aimed at undergoing reversible homolysis during nitroxide mediated polymerization. This cleavage results in the elimination of the terminal SG1 end-group as a radical, inducing a complete depolymerization process of the PS block from the so-formed radical cation. These successive eliminations of styrene molecules allowed a straightforward determination of the PS block size. An alternative fragmentation pathway of the radical cation was shown to provide structural information on the junction group between the two blocks. Proposed dissociation mechanisms were supported by accurate mass measurements. Structural information on the SG1 end-group could be reached from weak abundance fragment ions detected in the low m/z range of the MS/MS spectrum. Amongst fragments typically expected from PS dissociation, only beta ions were produced. Moreover, specific dissociation of the PEO block was not observed to occur in MS/MS, suggesting that these rearrangement reactions do not compete effectively with dissociations of the odd-electron fragment ions. Information about the PEO block length and the initiated end-group were obtained in MS(3) experiments.

Microporous polystyrene particles for selective carbon dioxide capture.

Science.gov (United States)

Kaliva, Maria; Armatas, Gerasimos S; Vamvakaki, Maria

2012-02-07

This study presents the synthesis of microporous polystyrene particles and the potential use of these materials in CO(2) capture for biogas purification. Highly cross-linked polystyrene particles are synthesized by the emulsion copolymerization of styrene (St) and divinylbenzene (DVB) in water. The cross-link density of the polymer is varied by altering the St/DVB molar ratio. The size and the morphology of the particles are characterized by scanning and transmission electron microscopy. Following supercritical point drying with carbon dioxide or lyophilization from benzene, the polystyrene nanoparticles exhibit a significant surface area and permanent microporosity. The dried particles comprising 35 mol % St and 65 mol % DVB possess the largest surface area, ∼205 m(2)/g measured by Brunauer-Emmett-Teller and ∼185 m(2)/g measured by the Dubinin-Radushkevich method, and a total pore volume of 1.10 cm(3)/g. Low pressure measurements suggest that the microporous polystyrene particles exhibit a good separation performance of CO(2) over CH(4), with separation factors in the range of ∼7-13 (268 K, CO(2)/CH(4) = 5/95 gas mixture), which renders them attractive candidates for use in gas separation processes.

Novel Programmable Shape Memory Polystyrene Film: A Thermally Induced Beam-power Splitter.

Science.gov (United States)

Li, Peng; Han, Yu; Wang, Wenxin; Liu, Yanju; Jin, Peng; Leng, Jinsong

2017-03-09

Micro/nanophotonic structures that are capable of optical wave-front shaping are implemented in optical waveguides and passive optical devices to alter the phase of the light propagating through them. The beam division directions and beam power distribution depend on the design of the micro/nanostructures. The ultimate potential of advanced micro/nanophotonic structures is limited by their structurally rigid, functional singleness and not tunable against external impact. Here, we propose a thermally induced optical beam-power splitter concept based on a shape memory polystyrene film with programmable micropatterns. The smooth film exhibits excellent transparency with a transmittance of 95% in the visible spectrum and optical stability during a continuous heating process up to 90 °C. By patterning double sided shape memory polystyrene film into erasable and switchable micro-groove gratings, the transmission light switches from one designed light divided directions and beam-power distribution to another because of the optical diffraction effect of the shape changing micro gratings during the whole thermal activated recovery process. The experimental and theoretical results demonstrate a proof-of-principle of the beam-power splitter. Our results can be adapted to further extend the applications of micro/nanophotonic devices and implement new features in the nanophotonics.

Enhanced sensitivity of a microfabricated resonator using a graphene-polystyrene bilayer membrane

Energy Technology Data Exchange (ETDEWEB)

Yun, Minhyuk; Lee, Eunho; Cho, Kilwon; Jeon, Sangmin, E-mail: jeons@postech.ac.kr [Department of Chemical Engineering, Pohang University of Science and Technology (POSTECH), Pohang (Korea, Republic of)

2014-08-18

A graphene layer was synthesized using chemical vapor deposition methods and a polystyrene solution was spin-cast onto the graphene film. The graphene-polystyrene bilayer membrane was attached between the two tines of a microfabricated quartz tuning fork (QTF). The modulus of the graphene-polystyrene bilayer was measured to be twice that of a pristine polystyrene membrane. Exposure of the membrane-coated QTF to ethanol vapor decreased the resonance frequency of the microresonator. The bilayer membrane-coated QTF produced a frequency change that was three times the change obtained using a polystyrene membrane-coated QTF, with a lower degree of degradation in the Q factor. The limit of detection of the bilayer membrane-coated QTF to ethanol vapor was determined to be 20 ppm.

The Study of the Microbes Degraded Polystyrene

Directory of Open Access Journals (Sweden)

Zhi-Long Tang

2017-01-01

Full Text Available Under the observation that Tenebrio molitor and Zophobas morio could eat polystyrene (PS, we setup the platform to screen the gut microbes of these two worms. To take advantage of that Tenebrio molitor and Zophobas morio can eat and digest polystyrene as its diet, we analyzed these special microbes with PS plate and PS turbidity system with time courses. There were two strains TM1 and ZM1 which isolated from Tenebrio molitor and Zophobas morio, and were identified by 16S rDNA sequencing. The results showed that TM1 and ZM1 were cocci-like and short rod shape Gram-negative bacteria under microscope. The PS plate and turbidity assay showed that TM1 and ZM1 could utilize polystyrene as their carbon sources. The further study of PS degraded enzyme and cloning warrants our attention that this platform will be an excellent tools to explore and solve this problem.

Mass distribution studies in 28Si + 232Th

International Nuclear Information System (INIS)

Sodaye, Suparna; Tripathi, R.; Sudarshan, K.; Pujari, P.K.

2014-01-01

Mass distribution is one of the important observables to understand the fusion-fission potential energy landscape. In the fission involving composite systems with Z ∼ 100, the fission barrier is lower and the saddle point is compact. Thus, apart from transfer induced fission,various non compound nucleus (NCN) fission processes like quasi-fission, pre-equilibrium fission and fast fission compete with the complete fusion fission (CFF). This would be further affected by the entrance channel parameters like choice of the target-projectile combination (mass asymmetry) and the projectile energy. Charge and mass distribution studies in such system would provide information about various fission processes such as complete fusion fission, non-compound nucleus fission and transfer induced fission, which would help in understanding the fusion-fission process in heavy ion collisions forming composite system in the heavy and trans-actinide region. In view of this, a systematic study of the charge and mass distribution in 28 Si+ 232 Th reaction was planned at beam energy close to and above the entrance channel Coulomb barrier. The experiments were carried out at the TIFR-LINAC booster facility. Self supporting foils of 232 Th were bombarded with 180 and 160 MeV 28 Si beam in a stack foil arrangement. The recoiling fission products were assayed radiochemically by off-line gamma-ray spectrometry. Results of charge distribution studies at E lab =180 MeV have been reported earlier. In the poster, the data on charge and mass distribution distribution will be presented.The results of the present studies will be compared with those from the reactions involving lighter and heavier composite systems

Formation of core (polystyrene)-shell (polybenzimidazole) nanoparticles using sulfonated polystyrene as template.

Science.gov (United States)

Hazarika, Mousumi; Arunbabu, Dhamodaran; Jana, Tushar

2010-11-15

We report formation of core (polystyrene)-shell (polybenzimidazole) nanoparticles from a new blend system consisting of an amorphous polymer polybenzimidazole (PBI) and an ionomer sodium salt of sulfonated polystyrene (SPS-Na). The ionomer used for the blending is spherical in shape with sulfonate groups on the surface of the particles. An in depth investigation of the blends at various sulfonation degrees and compositions using Fourier transform infrared (FT-IR) spectroscopy provides direct evidence of specific hydrogen bonding interactions between the N-H groups of PBI and the sulfonate groups of SPS-Na. The disruption of PBI chains self association owing to the interaction between the functional groups of these polymer pairs is the driving force for the blending. Thermodynamical studies carried out by using differential scanning calorimeter (DSC) establish partially miscible phase separated blending of these polymers in a wider composition range. The two distinguishable glass transition temperatures (T(g)) which are different from the neat components and unaltered with the blends composition attribute that the domain size of heterogeneity (d(d)) of the blends is >20 nm since one of the blend component (SPS-Na particle) diameter is ∼70 nm. The diminish of PBI chains self association upon blending with SPS-Na particles and the presence of invariant T(g)'s of the blends suggest the wrapping of PBI chains over the SPS-Na spherical particle surface and hence resulting a core-shell morphology. Transmission electron microscopy (TEM) study provides direct evidence of core-shell nanoparticle formation; where core is the polystyrene and shell is the PBI. The sulfonation degree affects the blends phase separations. The higher degree of sulfonation favors the disruption of PBI self association and thus forms partially miscible two phases blends with core-shell morphology. Copyright © 2010 Elsevier Inc. All rights reserved.

Behavior of positronium in polystyrene and its derivatives

International Nuclear Information System (INIS)

Honda, Y.; Watanabe, M.; Tashiro, M.; Terashima, Y.; Miyamoto, K.; Kimura, N.; Tagawa, S.

2003-01-01

The polystyrene, poly(4-bromostyrene) and poly(4-vinylphenol) are investigated using slow positron beam based on electron linac. There was a difference in the intensity of long-lived component of lifetime in o-Ps (τ 3 ). The S-parameter and the intensity of τ 3 were strongly influenced by the presence of the substituents of polystyrene. In thin films, irradiation effect caused by positron beam was observed

Combined effect of gamma radiation and stress cracking in polystyrene

International Nuclear Information System (INIS)

Amorim, Fernando A.; Rabello, Marcelo S.; Silva, Leonardo G.A.

2011-01-01

This study aimed to evaluate the combined effect of gamma radiation and stress cracking in polystyrene. Three different grades of polystyrene were analysed. The material was submitted to tensile tests and relaxation, analysis of molecular weight and determination of crosslinking. The results showed an increase in tensile strength in the specimens that had been exposed to radiation. The higher the molecular weight polystyrene showed better mechanical properties and after suffering the effects of gamma radiation there was an increase of 5.67% in the resistance to stress cracking effects. (author)

Green Synthesis, Characterization, and Antibacterial Activity of Silver/Polystyrene Nanocomposite

Directory of Open Access Journals (Sweden)

Manal A. Awad

2015-01-01

Full Text Available A novel, nontoxic, simple, cost-effective and ecofriendly technique was used to synthesize green silver nanoparticles (AgNPs. The AgNPs were synthesized using orange peel extract as a reducing agent for silver nitrate salt (AgNO3. The particle size distribution of AgNPs was determined by Dynamic Light Scattering (DLS. The average size of silver nanoparticles was 98.43 nm. The stable dispersion of silver nanoparticles was added slowly to polystyrene solution in toluene maintaining the temperature at 70°C. The AgNPs/polystyrene (PS nanocomposite solution was cast in a petri dish. The silver nanoparticles encapsulated within polymer chains were characterized by X-ray diffraction (XRD and Scanning Electron Microscopy (SEM equipped with Energy Dispersive Spectroscopy (EDS in addition to Transmission Electron Microscopy (TEM. The green AgNPs/PS nanocomposite film exhibited antimicrobial activity against Gram-negative bacteria Escherichia coli, Klebsiella pneumoniae and Salmonella, and Gram-positive bacteria Staphylococcus aureus. Thus, the key findings of the work include the use of a safe and simple AgNPs/PS nanocomposite which had a marked antibacterial activity which has a potential application in food packaging.

Invariant mass distributions in cascade decays

CERN Document Server

Miller, D J; Raklev, A R

2006-01-01

We derive analytical expressions for the shape of the invariant mass distributions of massless Standard Model endproducts in cascade decays involving massive New Physics (NP) particles, D -> Cc -> Bbc -> Aabc, where the final NP particle A in the cascade is unobserved and where two of the particles a, b, c may be indistinguishable. Knowledge of these expressions can improve the determination of NP parameters at the LHC. The shape formulas are composite, but contain nothing more complicated than logarithms of simple expressions. We study the effects of cuts, final state radiation and detector effects on the distributions through Monte Carlo simulations, using a supersymmetric model as an example. We also consider how one can deal with the width of NP particles and with combinatorics from the misidentification of final state particles. The possible mismeasurements of NP masses through `feet' in the distributions are discussed. Finally, we demonstrate how the effects of different spin configurations can be inclu...

Synthesis of polystyrene, poly(styrene/4-vinylpyridine), poly(p-nitrostyrene) and poly(p-aminostyrene)-coated silica and their extraction capabilities for amphetamine

International Nuclear Information System (INIS)

Sun Changmei; Zhang Shuanhong; Qu Rongjun; Sun Tao; Zhang Ying; Zhang Xiang; Song Jingyang

2010-01-01

Several novel organic-inorganic hybrid materials, including polystyrene-coated silica (SG-PS), poly(styrene/4-vinylpyridine)-coated silica (SG-PVP), poly(p-nitrostyrene)-coated silica (SG-PS-NO 2 ) and poly(p-aminostyrene)-coated silica (SG-PS-NH 2 ), were synthesized in order to improve the extraction methods of harmful stimulants via solid phase extraction. The materials were characterized using infrared spectra (IR), scanning electron microscope (SEM), Brunauer-Emmett-Teller (BET) surface area measurement and thermogravimetric analysis (TG). The application of the new materials in solid phase extraction columns to extract methamphetamine revealed that the extraction capability of poly(styrene/4-vinylpyridine)-coated silica is the best among the four materials, which provides novel supporter materials for extracting amphetamine-derived drugs.

Synthesis of polystyrene, poly(styrene/4-vinylpyridine), poly(p-nitrostyrene) and poly(p-aminostyrene)-coated silica and their extraction capabilities for amphetamine

Energy Technology Data Exchange (ETDEWEB)

Sun Changmei; Zhang Shuanhong [School of Chemistry and Materials Science, Ludong University, Yantai, Shandong 264025 (China); Qu Rongjun, E-mail: qurongjun@eyou.com [School of Chemistry and Materials Science, Ludong University, Yantai, Shandong 264025 (China); Sun Tao; Zhang Ying; Zhang Xiang; Song Jingyang [School of Chemistry and Materials Science, Ludong University, Yantai, Shandong 264025 (China)

2010-11-01

Several novel organic-inorganic hybrid materials, including polystyrene-coated silica (SG-PS), poly(styrene/4-vinylpyridine)-coated silica (SG-PVP), poly(p-nitrostyrene)-coated silica (SG-PS-NO{sub 2}) and poly(p-aminostyrene)-coated silica (SG-PS-NH{sub 2}), were synthesized in order to improve the extraction methods of harmful stimulants via solid phase extraction. The materials were characterized using infrared spectra (IR), scanning electron microscope (SEM), Brunauer-Emmett-Teller (BET) surface area measurement and thermogravimetric analysis (TG). The application of the new materials in solid phase extraction columns to extract methamphetamine revealed that the extraction capability of poly(styrene/4-vinylpyridine)-coated silica is the best among the four materials, which provides novel supporter materials for extracting amphetamine-derived drugs.

Partially-Functionalized Isotactic Polystyrene with Blocky Comonomer Segments

Science.gov (United States)

Siegel, Ariel; Powers, Wayne; Ryu, Chang Y.

2012-02-01

Isotactic polystyrenes (iPSs) have been functionalized in solution, while the accessibility of functionalizing agent is limited by the formation of crystalline domains at various temperatures. The chemical system used is the borylated isotactic polystyrene system, and we investigated the temperature effects on reaction kinetics to ultimately control the blockiness of borylated segments in the resulting copolymer. The chemical composition of partially borylated iPS reaches a steady state that is dependent on temperature. This synthesis has been performed at many different temperatures, with different steady states being reached at different temperatures. Further analysis by differential scanning calorimetry (DSC) has shown that the higher temperature reactions have greater effect on breaking down the crystal lattice structure of the isotactic polystyrene. As a result, the lower temperature reactions affect the crystalline structure less, and the resulting copolymer has more blockiness.

Polystyrene nanoparticles activate ion transport in human airway epithelial cells

Directory of Open Access Journals (Sweden)

McCarthy J

2011-06-01

Full Text Available J McCarthy1, X Gong2, D Nahirney2, M Duszyk2, MW Radomski11School of Pharmacy and Pharmaceutical Sciences, Panoz Institute, Trinity College Dublin, Dublin, Ireland; 2Department of Physiology, University of Alberta, Edmonton, Alberta, CanadaBackground: Over the last decade, nanotechnology has provided researchers with new nanometer materials, such as nanoparticles, which have the potential to provide new therapies for many lung diseases. In this study, we investigated the acute effects of polystyrene nanoparticles on epithelial ion channel function.Methods: Human submucosal Calu-3 cells that express cystic fibrosis transmembrane conductance regulator (CFTR and baby hamster kidney cells engineered to express the wild-type CFTR gene were used to investigate the actions of negatively charged 20 nm polystyrene nanoparticles on short-circuit current in Calu-3 cells by Ussing chamber and single CFTR Cl- channels alone and in the presence of known CFTR channel activators by using baby hamster kidney cell patches.Results: Polystyrene nanoparticles caused sustained, repeatable, and concentration-dependent increases in short-circuit current. In turn, these short-circuit current responses were found to be biphasic in nature, ie, an initial peak followed by a plateau. EC50 values for peak and plateau short-circuit current responses were 1457 and 315.5 ng/mL, respectively. Short-circuit current was inhibited by diphenylamine-2-carboxylate, a CFTR Cl- channel blocker. Polystyrene nanoparticles activated basolateral K+ channels and affected Cl- and HCO3- secretion. The mechanism of short-circuit current activation by polystyrene nanoparticles was found to be largely dependent on calcium-dependent and cyclic nucleotide-dependent phosphorylation of CFTR Cl- channels. Recordings from isolated inside-out patches using baby hamster kidney cells confirmed the direct activation of CFTR Cl- channels by the nanoparticles.Conclusion: This is the first study to identify

Mass distribution and evolutionary scheme for central stars of planetary nebulae

International Nuclear Information System (INIS)

Heap, S.R.; Augensen, H.J.; Widener Univ., Chester, PA)

1987-01-01

IUE data and a distance measuring method that considered central stars in optically thick nebulae were used to examine mass distributions of planetary nebulae. Other data such as spectral type, spatial and kinematic characteristics, etc., were studied to derive relationships between population type and mass distribution. A central star mass range of at least 0.55 solar mass was obtained. Stars with masses of at least 0.64 solar mass, concentrated in the galactic disk, originated from 1.5 solar mass stars. Low mass nuclei originated in old disk or halo populations and evolved from 1.0 solar mass objects. A mass-loss parameter value of 1/3 was calculated for red giants, implying that white dwarfs evolve from stars of under 5 solar masses. Mass distributions around planetary nuclei were concluded to follow patterns associated with the individual mass. 75 references

Renewable Aromatics from the Degradation of Polystyrene under Mild Conditions

KAUST Repository

Jabri, Nouf M

2017-05-25

A bimetallic FeCu/alumina catalyst was prepared and characterized. It showed excellent catalytic activity to quantitatively convert polystyrene (PS) into aromatics at low temperatures. A clear goldish yellow liquid was produced at 250 °C in a batch reactor without distillation. A liquid yield of 66% in an inert environment was achieved without the formation of coke and gas by-products. An exposure time of 90 min. and a catalyst loading of 200 mg were considered as an optimum condition to minimize the styrene re-polymerization. The gas chromatography/ mass spectrometry (GC/MS) analysis confirms that the primary products are styrene, ethylbenzene, cumene, toluene and α-methylstyrene.

Human plasma fibrinogen adsorption and platelet adhesion to polystyrene.

Science.gov (United States)

Tsai, W B; Grunkemeier, J M; Horbett, T A

1999-02-01

The purpose of this study was to further investigate the role of fibrinogen adsorbed from plasma in mediating platelet adhesion to polymeric biomaterials. Polystyrene was used as a model hydrophobic polymer; i.e., we expected that the role of fibrinogen in platelet adhesion to polystyrene would be representative of other hydrophobic polymers. Platelet adhesion was compared to both the amount and conformation of adsorbed fibrinogen. The strategy was to compare platelet adhesion to surfaces preadsorbed with normal, afibrinogenemic, and fibrinogen-replenished afibrinogenemic plasmas. Platelet adhesion was determined by the lactate dehydrogenase (LDH) method, which was found to be closely correlated with adhesion of 111In-labeled platelets. Fibrinogen adsorption from afibrinogenemic plasma to polystyrene (Immulon I(R)) was low and polystyrene preadsorbed with fibrinogen-replenished afibrinogenemic plasma. Addition of even small, subnormal concentrations of fibrinogen to afibrinogenemic plasma greatly increased platelet adhesion. In addition, surface-bound fibrinogen's ability to mediate platelet adhesion was different, depending on the plasma concentration from which fibrinogen was adsorbed. These differences correlated with changes in the binding of a monoclonal antibody that binds to the Aalpha chain RGDS (572-575), suggesting alteration in the conformation or orientation of the adsorbed fibrinogen. Platelet adhesion to polystyrene preadsorbed with blood plasma thus appears to be a strongly bivariate function of adsorbed fibrinogen, responsive to both low amounts and altered states of the adsorbed molecule. Copyright 1999 John Wiley & Sons, Inc.

X-ray excited luminescence of polystyrene composites loaded with SrF{sub 2} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Demkiv, T.M.; Halyatkin, O.O.; Vistovskyy, V.V. [Ivan Franko National University of Lviv, 8a Kyryla i Mefodiya St., 79005 Lviv (Ukraine); Hevyk, V.B. [Ivano-Frankivsk National Technical University of Oil and Gas, 15 Karpatska St., 76019 Ivano-Frankivsk (Ukraine); Yakibchuk, P.M. [Ivan Franko National University of Lviv, 8a Kyryla i Mefodiya St., 79005 Lviv (Ukraine); Gektin, A.V. [Institute for Scintillation Materials, NAS of Ukraine, 60 Lenina Ave, 61001 Kharkiv (Ukraine); Voloshinovskii, A.S. [Ivan Franko National University of Lviv, 8a Kyryla i Mefodiya St., 79005 Lviv (Ukraine)

2017-03-01

The polystyrene film nanocomposites of 0.3 mm thickness with embedded SrF{sub 2} nanoparticles up to 40 wt% have been synthesized. The luminescent and kinetic properties of the polystyrene composites with embedded SrF{sub 2} nanoparticles upon the pulse X-ray excitation have been investigated. The luminescence intensity of the pure polystyrene scintillator film significantly increases when it is loaded with the inorganic SrF{sub 2} nanoparticles. The film nanocomposites show fast (∼2.8 ns) and slow (∼700 ns) luminescence decay components typical for a luminescence of polystyrene activators (p-Terphenyl and POPOP) and SrF{sub 2} nanoparticles, respectively. It is revealed that the fast decay luminescence component of the polystyrene composites is caused by the excitation of polystyrene by the photoelectrons escaped from the nanoparticles due to photoeffect, and the slow component is caused by reabsorption of the self-trapped exciton luminescence of SrF{sub 2} nanoparticles by polystyrene.

Mass distribution law of systems of protocluster fragments

Energy Technology Data Exchange (ETDEWEB)

Ferraioli, F; Virgopia, N [Rome Univ. (Italy). Ist. di Matematica

1979-02-01

Starting from the hypothesis of coalescence through inelastic collisions of small fast moving interstellar gas clouds, an attempt has been made to study the evolutionary mass distribution of a system of fragments simulating a protocluster. The assumption of a mass spectrum with a continuous injection of newly formed entities into the primeval system, and the condition of gravitational reduction of the impact cross-section, have been considered. Comparisons of numerical experiments with the mass spectrum in some well-known young galactic clusters, confirm the mass distribution power-law already obtained by other authors. The empirical Schmidt's law concerning the rate of star formation is also confirmed. The hypothesis of the universal validity of the luminosity function, should not be 'a priori' rejected.

Improved synthesis of polystyrene-poly(ethylene oxide)-heparin block copolymers

NARCIS (Netherlands)

Vulic, I.; Loman, A.J.B.; Feijen, Jan; Okano, T.; Kim, S.W.

1990-01-01

A novel procedure for the synthesis of block copolymers composed of a hydrophobic block of polystyrene, a hydrophilic block of poly(ethylene oxide) and a bioactive block of nitrous acid-degraded heparin was developed. Amino-semitelechelic polystyrene was prepared by anionic polymerization of styrene

An Empirical Mass Function Distribution

Science.gov (United States)

Murray, S. G.; Robotham, A. S. G.; Power, C.

2018-03-01

The halo mass function, encoding the comoving number density of dark matter halos of a given mass, plays a key role in understanding the formation and evolution of galaxies. As such, it is a key goal of current and future deep optical surveys to constrain the mass function down to mass scales that typically host {L}\\star galaxies. Motivated by the proven accuracy of Press–Schechter-type mass functions, we introduce a related but purely empirical form consistent with standard formulae to better than 4% in the medium-mass regime, {10}10{--}{10}13 {h}-1 {M}ȯ . In particular, our form consists of four parameters, each of which has a simple interpretation, and can be directly related to parameters of the galaxy distribution, such as {L}\\star . Using this form within a hierarchical Bayesian likelihood model, we show how individual mass-measurement errors can be successfully included in a typical analysis, while accounting for Eddington bias. We apply our form to a question of survey design in the context of a semi-realistic data model, illustrating how it can be used to obtain optimal balance between survey depth and angular coverage for constraints on mass function parameters. Open-source Python and R codes to apply our new form are provided at http://mrpy.readthedocs.org and https://cran.r-project.org/web/packages/tggd/index.html respectively.

Incorporation of Nanohybrid Films of Silica into Recycled Polystyrene Matrix

Directory of Open Access Journals (Sweden)

Genoveva Hernández-Padrón

2015-01-01

Full Text Available An alternative for the reutilization of polystyrene waste containers consisting in creating a hybrid material made of SiO2 nanoparticles embedded in a matrix of recycled polystyrene (PSR has been developed. Recycled polystyrene functionalized (PSRF was used to influence the morphological and antifog properties by the sol-gel synthesis of nanohybrid silica. To this end, silica nanoparticles were produced from alkoxide precursors in the presence of recycled polystyrene. The functionalization of this polymeric matrix was with the purpose of uniting in situ carboxyl and silanol groups during the sol-gel process. In this way, opaque or transparent solid substrates can be obtained, with each of these endowed with optical conditions that depend on the amount of reactants employed to prepare each nanohybrid specimen. The nanohybrids were labelled as SiO2/PSR (HPSR and SiO2/PSRF (HPSRF and their properties were then compared to those of commercial polystyrene (PS. All the prepared samples were used for coating glass substrates. The hydrophobicity of the resultant coatings was determined through contact angle measurement. The nanohybrid materials were characterized by FT-IR and 1H-NMR techniques. Additionally, TGA and SEM were employed to determine their thermal and textural properties.

Charge and mass distribution in 20Ne induced fission of 181Ta

International Nuclear Information System (INIS)

Tripathi, R.; Sudarshan, K.; Goswami, A.; Reddy, A.V.R.; Guin, R.

2005-01-01

Charge and mass distribution studies have been carried out at E lab =180 MeV in 20 Ne induced fission of 181 Ta. The mass distribution has been found to be symmetric. The width of the mass distribution has been theoretically calculated using the random neck rupture of Brosa et al. A good agreement between the calculated and experimental mass distribution has been observed. (author)

Jordanian silica sand and cement as a reinforcement material for polystyrene matrix composites

International Nuclear Information System (INIS)

Jalham, S. I.

1999-01-01

The behaviour of polystyrene matrix composites with different percentages of Jordaanian Silica Sand as a Reinforcement Materials (0, 5, 25, 50, and 75 wt%) and different mean grain sizes of sand particles (60, 75, 85, and 300μ m) and with cement as a boning materials in the amount fo 1/6 wt% of the wt% of silica sand were manufactured and tested under compression loading in the Industrial Engineering Department as the Uninersity of Jordan as a part of large study on local materials. The main conclusions of this investigation are: a long-term, durable structure of the polystyrene composite reinforced by silica sand and cement was achieved by mixing the constituents with water; the higher the volume fraction of the reinforcement, the higher the volume fraction of reinforcement, the higher the strength while for 75% of reinforcement, the strength dropped to an amount less than that of the matrix; the higher the grain size, the higher the strength; longitudinal brittle fracture was observed for the composites, and a homogeneous distribution of the sand particles helped in increasing the strength of the composite by playing an important role in distributing the applied load. (author). 11 refs., 6 tabs, 2 figs

Microscopy evidence of the face-centered cubic arrangement of monodisperse polystyrene nanospheres

Energy Technology Data Exchange (ETDEWEB)

Zhang Hui [School of Science, Beijing Jiaotong University, Beijing 100044 (China)]. E-mail: zhanghui14305@sohu.com; Duan Renguan [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Li Fan [Department of Physical Chemistry, University of Science and Technology Beijing, Beijing 100083 (China); Tang Qing [Institute of Process Engineering, Chinese Academy of Sciences, Beijing 100080 (China); Li Wenchao [Department of Physical Chemistry, University of Science and Technology Beijing, Beijing 100083 (China)

2007-07-01

This paper reports a scanning electron microscopy (SEM) investigation of polystyrene artificial opal achieved through self-assembly of monodisperse polystyrene nanospheres with a diameter of 250 nm from colloidal suspension after being ambient dried. A detailed analysis of the SEM images verifies that the face-centered cubic (fcc) phase is the most stable one for the polystyrene opal prepared. This finding provides a strong support for, by using polystyrene opal as template, fabricating a photonic crystal with inverse fcc structure of full band gap if the refractive index contrast is higher than 2.8 and the filling fraction of the high index materials is between 0.2 and 0.3.

Microscopy evidence of the face-centered cubic arrangement of monodisperse polystyrene nanospheres

International Nuclear Information System (INIS)

Zhang Hui; Duan Renguan; Li Fan; Tang Qing; Li Wenchao

2007-01-01

This paper reports a scanning electron microscopy (SEM) investigation of polystyrene artificial opal achieved through self-assembly of monodisperse polystyrene nanospheres with a diameter of 250 nm from colloidal suspension after being ambient dried. A detailed analysis of the SEM images verifies that the face-centered cubic (fcc) phase is the most stable one for the polystyrene opal prepared. This finding provides a strong support for, by using polystyrene opal as template, fabricating a photonic crystal with inverse fcc structure of full band gap if the refractive index contrast is higher than 2.8 and the filling fraction of the high index materials is between 0.2 and 0.3

Radiation-induced chemical processes in polystyrene scintillators

International Nuclear Information System (INIS)

Milinchuk, V.K.; Bolbit, N.M.; Klinshpont, E.R.; Tupikov, V.I.; Zhdanov, G.S.; Taraban, S.B.; Shelukhov, I.P.; Smoljanskii, A.S.

1999-01-01

The regularities established for macroradical accumulation and intensity of radioluminescence under γ-irradiation of a polystyrene scintillator prove benzyl macroradicals to be efficient quenchers of the excited scintillator molecules. Dissolved oxygen was determined to have a constant of the quenching rate 100 times lower than that of macroradicals. Oxygen is an efficient antirad because of participating in oxidation reactions and subsequent recombination of macroradicals. The method was developed to obtain a polymeric scintillator with a polystyrene matrix containing a dispersed system of pores and channels. Radiation resistance of such a scintillator is 5-10 times higher than that of standard types

Possible mass distributions in the nebulae of other solar systems

International Nuclear Information System (INIS)

Brown, W.K.

1987-01-01

The supernova shell fragmentation model of solar system formation - previously shown to be successful in describing the mass distribution of our solar system - is used to calculate the mass distributions of other solar nebulae. (Auth.)

RESEARCHES OF WORKING LIFE OF FOAM POLYSTYRENE OF BUILDING APPOINTMENT

Directory of Open Access Journals (Sweden)

Guyumdzhjan Perch Pogosovich

2012-09-01

Full Text Available Results of experimental researches of physicomechanical properties of foam polystyrene thermal insulation materials are presented in article. The operational resource was defined on materials subject to ageing, action of liquid excited environments and atmospheric impacts. The destructive processes leading to destruction of foam polystyrene are revealed.

Characterization of SWNT based Polystyrene Nanocomposites

Science.gov (United States)

Mitchell, Cynthia; Bahr, Jeffrey; Tour, James; Arepalli, Sivaram; Krishnamoorti, Ramanan

2003-03-01

Polystyrene nanocomposites with functionalized single walled carbon nanotubes (SWNTs), prepared by the in-situ generation and addition of organic diazonium compounds, were characterized using a range of structural and dynamic methods. These were contrasted to the properties of polystyrene composites prepared with unfunctionalized SWNTs at the same loadings. The functionalized nanocomposites demonstrated a percolated SWNT network structure at concentrations of 1 vol SWNT based composites at similar loadings of SWNT exhibited behavior comparable to that of the unfilled polymer. This formation of the SWNT network structure is because of the improved compatibility between the SWNTs and the polymer matrix due to the functionalization. Further structural evidence for the compatibility of the modified SWNTs and the polymer matrix will be discussed in the presentation.

A Dual Power Law Distribution for the Stellar Initial Mass Function

Science.gov (United States)

Hoffmann, Karl Heinz; Essex, Christopher; Basu, Shantanu; Prehl, Janett

2018-05-01

We introduce a new dual power law (DPL) probability distribution function for the mass distribution of stellar and substellar objects at birth, otherwise known as the initial mass function (IMF). The model contains both deterministic and stochastic elements, and provides a unified framework within which to view the formation of brown dwarfs and stars resulting from an accretion process that starts from extremely low mass seeds. It does not depend upon a top down scenario of collapsing (Jeans) masses or an initial lognormal or otherwise IMF-like distribution of seed masses. Like the modified lognormal power law (MLP) distribution, the DPL distribution has a power law at the high mass end, as a result of exponential growth of mass coupled with equally likely stopping of accretion at any time interval. Unlike the MLP, a power law decay also appears at the low mass end of the IMF. This feature is closely connected to the accretion stopping probability rising from an initially low value up to a high value. This might be associated with physical effects of ejections sometimes (i.e., rarely) stopping accretion at early times followed by outflow driven accretion stopping at later times, with the transition happening at a critical time (therefore mass). Comparing the DPL to empirical data, the critical mass is close to the substellar mass limit, suggesting that the onset of nuclear fusion plays an important role in the subsequent accretion history of a young stellar object.

Mass measurement errors of Fourier-transform mass spectrometry (FTMS): distribution, recalibration, and application.

Science.gov (United States)

Zhang, Jiyang; Ma, Jie; Dou, Lei; Wu, Songfeng; Qian, Xiaohong; Xie, Hongwei; Zhu, Yunping; He, Fuchu

2009-02-01

The hybrid linear trap quadrupole Fourier-transform (LTQ-FT) ion cyclotron resonance mass spectrometer, an instrument with high accuracy and resolution, is widely used in the identification and quantification of peptides and proteins. However, time-dependent errors in the system may lead to deterioration of the accuracy of these instruments, negatively influencing the determination of the mass error tolerance (MET) in database searches. Here, a comprehensive discussion of LTQ/FT precursor ion mass error is provided. On the basis of an investigation of the mass error distribution, we propose an improved recalibration formula and introduce a new tool, FTDR (Fourier-transform data recalibration), that employs a graphic user interface (GUI) for automatic calibration. It was found that the calibration could adjust the mass error distribution to more closely approximate a normal distribution and reduce the standard deviation (SD). Consequently, we present a new strategy, LDSF (Large MET database search and small MET filtration), for database search MET specification and validation of database search results. As the name implies, a large-MET database search is conducted and the search results are then filtered using the statistical MET estimated from high-confidence results. By applying this strategy to a standard protein data set and a complex data set, we demonstrate the LDSF can significantly improve the sensitivity of the result validation procedure.

Insecticide-treated nets mass distribution campaign: benefits and lessons in Zambia.

Science.gov (United States)

Masaninga, Freddie; Mukumbuta, Nawa; Ndhlovu, Ketty; Hamainza, Busiku; Wamulume, Pauline; Chanda, Emmanuel; Banda, John; Mwanza-Ingwe, Mercy; Miller, John M; Ameneshewa, Birkinesh; Mnzava, Abraham; Kawesha-Chizema, Elizabeth

2018-04-24

Zambia was an early adopter of insecticide-treated nets strategy in 2001, and policy for mass distribution with long-lasting insecticidal nets (LLINs) in 2005. Since then, the country has implemented mass distribution supplemented with routine delivery through antenatal care and under five clinics in health facilities. The national targets of universal (100%) coverage and 80% utilization of LLINs have not been attained. Free mass LLIN distribution campaign in Zambia offers important lessons to inform future campaigns in the African region. This study reviewed LLIN free mass distribution campaign information derived from Zambia's national and World Health Organization Global Malaria Programme annual reports and strategic plans published between 2001 and 2016. In 2014, a nationwide mass distribution campaign in Zambia delivered all the 6.0 million LLINs in 6 out of 10 provinces in 4 months between June and September before the onset of the rainy season. Compared with 235,800 LLINs and 2.9 million LLINs distributed on a rolling basis in 2008 and 2013, respectively, the 2014 mass campaign, which distributed 6 million LLINs represented the largest one-time-nationwide LLIN distribution in Zambia. The province (Luapula) with highest malaria transmission, mostly with rural settings recorded 98-100% sleeping spaces in homes covered with LLINs. The percentage of households owning at least 1 LLIN increased from 50.9% in 2006 to 77.7% in 2015. The 2014 mass campaign involved a coordinated response with substantial investments into macro (central) and micro (district) level planning, capacity building, tracking and logistics management supported by a new non-health sector partnership landscape. Coordination of LLIN distribution and logistics benefited from the mobile phone technology to transmit "real time" data on commodity tracking that facilitated timely delivery to districts. Free mass distribution of LLINs policy was adopted in 2005 in Zambia. Consistently implemented

Pyrolysis of polystyrene waste in the presence of activated carbon in conventional and microwave heating using modified thermocouple.

Science.gov (United States)

Prathiba, R; Shruthi, M; Miranda, Lima Rose

2018-06-01

Pyrolysis process was experimented using two types of heating source, namely conventional and microwave. Polystyrene (PS) plastic waste was used as feedstock in a batch reactor for both the conventional (slow pyrolysis) and microwave pyrolysis. The effect of activated carbon to polystyrene ratio on (i) yield of oil, gas and residues (ii) reaction temperature (iii) reaction time were studied. Quality of oil from pyrolysis of polystyrene were assessed for the possible applicability in fuel production. Microwave power of 450 W and polymer to activated carbon ratio of 10:1, resulted in the highest oil yield of 93.04 wt.% with a higher heating value of 45 MJ kg -1 and a kinematic viscosity of 2.7 cSt. Microwave heating when compared to conventional heating method, exhibits a reaction temperature and time of 330 °C in 5.5 min, whereas in conventional heating system it was 418 °C in 60 min. The gas chromatography-mass spectrometry analysis of liquid oil from microwave pyrolysis predominantly yields alkenes of 8.44 wt.%, α-methyl styrene 0.96 wt.%, condensed ring aromatics 23.21 wt.% and benzene derivatives 26.77 wt.% when the polystyrene to activated carbon ratio was 10:1. Significant factor of using microwave heating is the amount of energy converted (kWh) is lesser than conventional heating. Copyright © 2018 Elsevier Ltd. All rights reserved.

A study of the deep structure of the energy landscape of glassy polystyrene: the exponential distribution of the energy barriers revealed by high-field electron spin resonance spectroscopy

International Nuclear Information System (INIS)

Bercu, V; Martinelli, M; Massa, C A; Pardi, L A; Leporini, D

2004-01-01

The reorientation of one small paramagnetic molecule (spin probe) in glassy polystyrene (PS) is studied by high-field electron spin resonance spectroscopy at two different Larmor frequencies (190 and 285 GHz). The exponential distribution of the energy barriers for the rotational motion of the spin probe is unambiguously evidenced at both 240 and 270 K. The same shape for the distribution of the energy barriers of PS was evidenced by the master curves provided by previous mechanical and light scattering studies. The breadth of the energy barrier distribution of the spin probe is in the range of the estimates of the breadth of the PS energy barrier distribution. The evidence that the deep structure of the energy landscape of PS exhibits the exponential shape of the energy barrier distribution agrees with the results from extreme-value statistics (Bouchaud and Mezard 1997 J. Phys. A: Math. Gen. 30 7997) and the trap model by Bouchaud and co-workers (1996 J. Phys. A: Math. Gen. 29 3847, 2001 Phys. Rev. B 64 104417). (letter to the editor)

Mass formula dependence of calculated spallation reaction product distributions

International Nuclear Information System (INIS)

Nishida, Takahiko; Nakahara, Yasuaki

1990-01-01

A new version of the spallation reaction simulation code NUCLEUS was developed by incorporating Uno and Yamada's mass formula. This version was used to calculate the distribution of products from the spallation of uranium nuclei by high-energy protons. The dependence of the distributions on the mass formula was examined by comparing the results with those from the original version, which is based on Cameron's mass formula and the mass table compiled by Wapstra et al. As regards the fission component of spallation products, the new version reproduces the reaction product data obtained from thin foil experiments much better, especially on the neutron excess side. (orig.) [de

Preparation of tritiated polystyrene and its application in radio luminescent paints

International Nuclear Information System (INIS)

Ravi, S.; Mathewy, K.M.; Seshadri, N.K.; Subramanian, T.K.

2001-01-01

Beta radiation emanating from tritiated polystyrene in close proximity with copper activated zinc sulphide phosphor will provide self-sustained light sources and are used for nocturnal illumination of watches and clocks, product advertisements, telephone numbers, exit signs etc. Phenylacetylene was partially reduced in diethyl ether medium with tritium using 5% Pd/C poisoned with quinoline to give styrene. Styrene formed was polymerised to polystyrene by subjecting it to irradiation with γ-radiation (20 mega rad dose). Copper activated zinc sulphide phosphor was coated with tritiated polystyrene to give self-sustained light sources. (author)

Amino-modified polystyrene nanoparticles affect signalling pathways of the sea urchin (Paracentrotus lividus) embryos.

Science.gov (United States)

Pinsino, Annalisa; Bergami, Elisa; Della Torre, Camilla; Vannuccini, Maria Luisa; Addis, Piero; Secci, Marco; Dawson, Kenneth A; Matranga, Valeria; Corsi, Ilaria

2017-03-01

Polystyrene nanoparticles have been shown to pose serious risk to marine organisms including sea urchin embryos based on their surface properties and consequently behaviour in natural sea water. The aim of this study is to investigate the toxicity pathways of amino polystyrene nanoparticles (PS-NH 2 , 50 nm) in Paracentrotus lividus embryos in terms of development and signalling at both protein and gene levels. Two sub-lethal concentrations of 3 and 4 μg/mL of PS-NH 2 were used to expose sea urchin embryos in natural sea water (PS-NH 2 as aggregates of 143 ± 5 nm). At 24 and 48 h post-fertilisation (hpf) embryonic development was monitored and variations in the levels of key proteins involved in stress response and development (Hsp70, Hsp60, MnSOD, Phospho-p38 Mapk) as well as the modulation of target genes (Pl-Hsp70, Pl-Hsp60, Pl-Cytochrome b, Pl-p38 Mapk, Pl-Caspase 8, Pl-Univin) were measured. At 48 hpf various striking teratogenic effects were observed such as the occurrence of cells/masses randomly distributed, severe skeletal defects and delayed development. At 24 hpf a significant up-regulation of Pl-Hsp70, Pl-p38 Mapk, Pl-Univin and Pl-Cas8 genes was found, while at 48 hpf only for Pl-Univin was observed. Protein profile showed different patterns as a significant increase of Hsp70 and Hsp60 only after 48 hpf compared to controls. Conversely, P-p38 Mapk protein significantly increased at 24 hpf and decreased at 48 hpf. Our findings highlight that PS-NH 2 are able to disrupt sea urchin embryos development by modulating protein and gene profile providing new understandings into the signalling pathways involved.

Investigation the effect of time detention on the removal of chromuim from aqueous solution by using polyaniline/polystyrene nanocomposite

International Nuclear Information System (INIS)

Eisazade, Hossein; Davodi, Behzad; Soleimani lashkenari, Mohammad

2010-01-01

In this study Polyaniline/polystyrene nanocomposites were prepared in the aqueous solution by using ammonium peroxy disulfate as an oxidant in the presence of poly (vinyl pyrrolidone) as surfactant. Morphology and chemical structure was characterized by using scaning electron micrograph(SEM), fourier transform infrared (FTIR) spectrometer and removal percentage obtained by using mass atomic absorption.

Structural analysis of syndiotactic polystyrene

Energy Technology Data Exchange (ETDEWEB)

Mitani, Masahiro

1988-09-01

Since the stereostructure of a high-molecular compound includes three types of isotactic, atactic and sydiotactic structures, a high-molecular compound with excellent properties can be produced by controlling the stereogularity of the compound with the identical composition. The stereoregularity of a stereogular polystyrene, or syndiotactic polystyrene (SPS), which had been successfully synthesized recently was quantitatively determined and the open chain structure by polymerization was investigated by nuclear magnetic resonance spectroscopy. Two SPSs were synthesized from cis-beta-d/sub/1-styrene and trans-beta-d/sub/1-styrene with alpha, beta, beta-d/sub/3-styrene. The results of spectral analysis of these two SPSs indicate that the former is of trans-conformation and the latter is of gauche conformation and that accordingly the open chain structure by polymerization of SPS is of cis-open chain and SPS has a planar zigzag structure even in the solution. (5 figs, 9 refs)

Facile approach in fabricating superhydrophobic ZnO/polystyrene nanocomposite coating

Science.gov (United States)

Qing, Yongquan; Zheng, Yansheng; Hu, Chuanbo; Wang, Yong; He, Yi; Gong, Yong; Mo, Qian

2013-11-01

In this paper, we report a simple and inexpensive method for fabricating modified-ZnO/polystyrene superhydrophobic surface on the cotton textiles. The surface wettability and topology of coating were characterized by contact angle measurement, Scanning electron microscope and Fourier transform infrared spectrometry. The results showed that the hydrophobic CH3 and CF2 group was introduced into ZnO particles via modification, the ZnO nanoparticles were modified from hydrophilic to hydrophobic. When the weight ratio of modified-ZnO to polystyrene was 7:3, the ZnO/polystyrene composite coating contact angle was 158°, coating surface with hierarchical micro/nano structures. Furthermore, the superhydrophobic cotton texiles have a very extensive application prospect in water-oil separation.

Fabrication of polystyrene microfluidic devices using a pulsed CO2 laser system

KAUST Repository

Li, Huawei

2013-10-10

In this article, we described a simple and rapid method for fabrication of droplet microfluidic devices on polystyrene substrate using a CO2 laser system. The effects of the laser power and the cutting speed on the depth, width and aspect ratio of the microchannels fabricated on polystyrene were investigated. The polystyrene microfluidic channels were encapsulated using a hot press bonding technique. The experimental results showed that both discrete droplets and laminar flows could be obtained in the device.

Fabrication of polystyrene microfluidic devices using a pulsed CO2 laser system

KAUST Repository

Li, Huawei; Fan, Yiqiang; Foulds, Ian G.; Kodzius, Rimantas

2013-01-01

In this article, we described a simple and rapid method for fabrication of droplet microfluidic devices on polystyrene substrate using a CO2 laser system. The effects of the laser power and the cutting speed on the depth, width and aspect ratio of the microchannels fabricated on polystyrene were investigated. The polystyrene microfluidic channels were encapsulated using a hot press bonding technique. The experimental results showed that both discrete droplets and laminar flows could be obtained in the device.

Reconsideration of mass-distribution models

Directory of Open Access Journals (Sweden)

Ninković S.

2014-01-01

Full Text Available The mass-distribution model proposed by Kuzmin and Veltmann (1973 is revisited. It is subdivided into two models which have a common case. Only one of them is subject of the present study. The study is focused on the relation between the density ratio (the central one to that corresponding to the core radius and the total-mass fraction within the core radius. The latter one is an increasing function of the former one, but it cannot exceed one quarter, which takes place when the density ratio tends to infinity. Therefore, the model is extended by representing the density as a sum of two components. The extension results into possibility of having a correspondence between the infinite density ratio and 100% total-mass fraction. The number of parameters in the extended model exceeds that of the original model. Due to this, in the extended model, the correspondence between the density ratio and total-mass fraction is no longer one-to-one; several values of the total-mass fraction can correspond to the same value for the density ratio. In this way, the extended model could explain the contingency of having two, or more, groups of real stellar systems (subsystems in the diagram total-mass fraction versus density ratio. [Projekat Ministarstva nauke Republike Srbije, br. 176011: Dynamics and Kinematics of Celestial Bodies and Systems

Instantaneous x-ray radiation energy from laser produced polystyrene plasmas for shock ignition conditions

International Nuclear Information System (INIS)

Shang, Wanli; Wei, Huiyue; Li, Zhichao; Yi, Rongqing; Zhu, Tuo; Song, Tianmin; Huang, Chengwu; Yang, Jiamin

2013-01-01

Laser target energy coupling mechanism is crucial in the shock ignition (SI) scheme, and x-ray radiation energy is a non-negligible portion of the laser produced plasma energy. To evaluate the x-ray radiation energy amount at conditions relevant to SI scheme, instantaneous x-ray radiation energy is investigated experimentally with continuum phase plates smoothed lasers irradiating layer polystyrene targets. Comparative laser pulses without and with shock spike are employed. With the measured x-ray angular distribution, full space x-ray radiation energy and conversion efficiency are observed. Instantaneous scaling law of x-ray conversion efficiency is obtained as a function of laser intensity and time. It should be pointed out that the scaling law is available for any laser pulse shape and intensity, with which irradiates polystyrene planar target with intensity from 2 × 10 14 to 1.8 × 10 15 W/cm 2 . Numerical analysis of the laser energy transformation is performed, and the simulation results agree with the experimental data

Effects of water on starch-g-polystyrene and starch-g-poly(methyl acrylate) extrudates

International Nuclear Information System (INIS)

Henderson, A.M.; Rudin, A.

1982-01-01

Polystyrene and poly(methyl acrylate) were grafted onto wheat starch by gamma radiation and chemical initiation, respectively. The respective percent add-on values were 46 and 45; 68% of the polystyrene formed was grafted to starch, and corresponding proportion of poly(methyl acrylate) was 41%. The molecular weight distributions of the homopolymer and graft portions were characterized, and extrusion conditions were established for production of ribbon samples of starch-g-PS and starch-g-PMA. Both copolymer types were considerably weakened by soaking in water, and this effect was more immediate and drastic for starch-g-poly(methyl acrylate). Both graft copolymers regained their original tensile strengths on drying, but the poly(methyl acrylate) specimens did not recover their original unswollen dimensions and retained high breaking elongations characteristic of soaked specimens. Tensile and dynamic mechanical properties of extruded and molded samples of both graft polymers are reported, and plasticizing effects of water are summarized

On the Importance of Purification of Sodium Polystyrene Sulfonate

OpenAIRE

Sen, Akhil K.; Roy, Sandip; Juvekar, Vinay A.

2012-01-01

Ion exchange is commonly employed for purification of sodium polystyrene sulfonate (NaPSS), a molecule widely used as a model polyelectrolyte. However, the present work demonstrates that the ion exchange process itself may introduce some extraneous species into NaPSS samples by two possible mechanisms: (i) chemical transformation of polystyrene sulfonic acid (HPSS), a relatively unstable intermediate formed during ion exchange and (ii) release of small amount of “condensed” acid from cationic...

Reflection electron energy loss spectroscopy as efficient technique for the determination of optical properties of polystyrene intermixed with gold nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Deris, Jamileh [Department of Physics, Yasouj University, Yasouj 75918-74831 (Iran, Islamic Republic of); Hajati, Shaaker, E-mail: Hajati@mail.yu.ac.ir [Department of Physics, Yasouj University, Yasouj 75918-74831 (Iran, Islamic Republic of); Department of Semiconductors, Materials and Energy Research Center, Karaj 3177983634 (Iran, Islamic Republic of)

2017-01-15

Highlights: • Reflection Electron Energy Loss Spectroscopy of nano-metalized polymer. • Determination of real part of the dielectric function of nanostructured sample. • Determination of imaginary part of the dielectric function of nanostructured sample. • Determination of refractive index and coefficient of extinction of the sample. • Determination of reflection and absorption coefficients of nano-metalized Polymer. - Abstract: The electronic properties (electron inelastic cross section, energy loss function) of a nano-metalized polystyrene obtained by reflection electron energy loss spectroscopy (REELS) in a previous study [J. Deris, S. Hajati, S. Tougaard, V. Zaporojtchenko, Appl. Surf. Sci. 377 (2016) 44–47], which relies on the Yubero-Tougaard method, were used in the complementary application of Kramers-Kronig transformation to determine its optical properties such as the real part (ε{sub 1}) and imaginary part (ε{sub 2}) of the dielectric function (ε), refractive index (n), coefficients of extinction (k), reflection (R) and absorption (μ). The degree of intermixing of polystyrene thin film and gold nanoparticles of sizes 5.5 nm was controlled by annealing the sample to achieve a morphology in which the nanoparticles were homogeneously distributed within polystyrene. It is worth noting that no data are available on the optical properties of metalized polymers such as gold nanoparticles intermixed with polystyrene. Therefore, this work is of high importance in terms of both the sample studied here and the method applied. The advantage of the method applied here is that no information on the lateral distribution of the nanocomposite sample is required. This means that the REELS technique has been presented here to suitably, efficiently and easily obtain the optical properties of such nano-metalized polymer in which the metal nanoparticles have been vertically well distributed (homogeneous in depth). Therefore, for vertically homogeneous and

Mass distribution in 20Ne+232Th reaction

International Nuclear Information System (INIS)

Sodaye, Suparna; Tripathi, R.; Sudarshan, K.

2011-01-01

Mass distribution was measured in 20 Ne+ 232 Th reaction at E lab =145 MeV using recoil catcher technique followed by off-line gamma-ray spectrometry. Significant contribution from transfer fission was observed in the yield of comparatively neutron rich fission products. The variance of mass distribution for complete fusion fission, obtained by excluding neutron rich fission products, was observed to be consistent with the values reported in literature for similar reaction systems which showed a deviation from the systematics obtained using random neck rupture and liquid drop model. (author)

Synthesis and characterization of polystyrene-poly(ethylene oxide)-heparin block copolymers

NARCIS (Netherlands)

Vulić, I.; Okano, T.; Kim, S.W.; Feijen, Jan

1988-01-01

A procedure for the preparation of new block copolymers composed of a hydrophobic block of polystyrene, a hydrophilic spacer-block of poly(ethylene oxide) and a bioactive block of heparin was investigated. Polystyrene with one amino group per chain was synthesized by free radical oligomerization of

Copolymers of fluorinated polydienes and sulfonated polystyrene

Science.gov (United States)

Mays, Jimmy W [Knoxville, TN; Gido, Samuel P [Hadley, MA; Huang, Tianzi [Knoxville, TN; Hong, Kunlun [Knoxville, TN

2009-11-17

Copolymers of fluorinated polydienes and sulfonated polystyrene and their use in fuel cell membranes, batteries, breathable chemical-biological protective materials, and templates for sol-gel polymerization.

Serotyping of Actinobacillus pleuropneumoniae serotype 5 strains using a monoclonal-based polystyrene agglutination test

DEFF Research Database (Denmark)

Dubreuil, J.D.; Letellier, A.; Stenbæk, Eva

1996-01-01

A polystyrene agglutination test has been developed for serotyping Actinobacillus pleuropneumoniae serotype 5a and 5b strains. Protein A-coated polystyrene microparticles were sensitized with a murine monoclonal antibody recognizing an epitope on serotype 5 LPS-O chain as shown by SDS-PAGE and We......A polystyrene agglutination test has been developed for serotyping Actinobacillus pleuropneumoniae serotype 5a and 5b strains. Protein A-coated polystyrene microparticles were sensitized with a murine monoclonal antibody recognizing an epitope on serotype 5 LPS-O chain as shown by SDS...... suspension of bacterial cells grown for 18 h. All A, pleuropneumoniae strains had been previously serotyped using standard procedures, The polystyrene agglutination test was rapid (less than 3 min) and easy to perform. Overall a very good correlation (97.3%) with the standard techniques was found...

Variable Lysozyme Transport Dynamics on Oxidatively Functionalized Polystyrene Films.

Science.gov (United States)

Moringo, Nicholas A; Shen, Hao; Tauzin, Lawrence J; Wang, Wenxiao; Bishop, Logan D C; Landes, Christy F

2017-10-17

Tuning protein adsorption dynamics at polymeric interfaces is of great interest to many biomedical and material applications. Functionalization of polymer surfaces is a common method to introduce application-specific surface chemistries to a polymer interface. In this work, single-molecule fluorescence microscopy is utilized to determine the adsorption dynamics of lysozyme, a well-studied antibacterial protein, at the interface of polystyrene oxidized via UV exposure and oxygen plasma and functionalized by ligand grafting to produce varying degrees of surface hydrophilicity, surface roughness, and induced oxygen content. Single-molecule tracking indicates lysozyme loading capacities, and surface mobility at the polymer interface is hindered as a result of all functionalization techniques. Adsorption dynamics of lysozyme depend on the extent and the specificity of the oxygen functionalities introduced to the polystyrene surface. Hindered adsorption and mobility are dominated by hydrophobic effects attributed to water hydration layer formation at the functionalized polystyrene surfaces.

Polystyrene microplastics induce microbiota dysbiosis and inflammation in the gut of adult zebrafish.

Science.gov (United States)

Jin, Yuanxiang; Xia, Jizhou; Pan, Zihong; Yang, Jiajing; Wang, Wenchao; Fu, Zhengwei

2018-04-01

Microplastic (MP) are environmental pollutants and have the potential to cause varying degrees of aquatic toxicity. In this study, the effects on gut microbiota of adult male zebrafish exposed for 14 days to 100 and 1000 μg/L of two sizes of polystyrene MP were evaluated. Both 0.5 and 50 μm-diameter spherical polystyrene MP increased the volume of mucus in the gut at a concentration of 1000 μg/L (about 1.456 × 10 10 particles/L for 0.5 μm and 1.456 × 10 4 particles/L for 50 μm). At the phylum level, the abundance of Bacteroidetes and Proteobacteria decreased significantly and the abundance of Firmicutes increased significantly in the gut after 14-day exposure to 1000 μg/L of both sizes of polystyrene MP. In addition, high throughput sequencing of the 16S rRNA gene V3-V4 region revealed a significant change in the richness and diversity of microbiota in the gut of polystyrene MP-exposed zebrafish. A more in depth analysis, at the genus level, revealed that a total of 29 gut microbes identified by operational taxonomic unit (OTU) analysis were significantly changed in both 0.5 and 50 μm-diameter polystyrene MP-treated groups. Moreover, it was observed that 0.5 μm polystyrene MP not only increased mRNA levels of IL1α, IL1β and IFN but also their protein levels in the gut, indicating that inflammation occurred after polystyrene MP exposure. Our findings suggest that polystyrene MP could induce microbiota dysbiosis and inflammation in the gut of adult zebrafish. Copyright © 2017 Elsevier Ltd. All rights reserved.

Mass distribution of fission fragments within the Born-Oppenheimer approximation

Energy Technology Data Exchange (ETDEWEB)

Pomorski, K.; Nerlo-Pomorska, B. [M.C.S. University, Department of Theoretical Physics, Lublin (Poland); Ivanyuk, F.A. [Institute for Nuclear Research, Kiev (Ukraine)

2017-03-15

The fission fragments mass-yield of {sup 236} U is obtained by an approximate solution of the eigenvalue problem of the collective Hamiltonian that describes the dynamics of the fission process whose degrees of freedom are: the fission (elongation), the neck and mass-asymmetry modes. The macroscopic-microscopic method is used to evaluate the potential energy surface. The macroscopic energy part is calculated using the liquid drop model and the microscopic corrections are obtained using a Woods-Saxon single-particle levels. The four-dimensional modified Cassini ovals shape parametrization is used to describe the shape of the fissioning nucleus. The mass tensor is taken within a cranking-type approximation. The final fragment mass distribution is obtained by weighting the adiabatic density distribution in the collective space with the neck-dependent fission probability. The neck degree of freedom is found to play a significant role in determining the final fragment mass distribution. (orig.)

Wettability control of polystyrene by ion implantation

International Nuclear Information System (INIS)

Suzuki, Yoshiaki; Kusakabe, Masahiro; Iwaki, Masaya

1994-01-01

The permanent effects of ion implantation on the improvement of wettability of polystyrene is investigated in relation to ion species and fluences. The He + , Ne + , Na + , N 2 + , O 2 + , Ar + , K + and Kr + ion implantations were performed at energies of 50 and 150 keV at room temperature. The fluences ranged from 1x10 15 to 1x10 17 ions/cm 2 . The results showed that the contact angle of water for Na + and K + implanted polystyrene decreased from 87 to 0 , as the fluences increased to 1x10 17 ions/cm 2 at an energy of 50 keV. The contact angle for Na + and K + implanted polystyrene did not change under ambient room conditions, even when time elapsed. However, the contact an gle for He + , C + , O + , Ne + , N 2 + , O 2 + , Ar + , and Kr + ion implanted specimens decreased slightly immediately after ion implantation. Results of X-ray photoelectron spectroscopy showed that the increase in the Na content in the surface of Na + implanted specimens were observed with increasing fluence. It is concluded that permanent improvement in wettability was caused by doping effects rather than by radiation effects from Na + and K + ion implantation. ((orig.))

Vibration Analysis of Inclined Laminated Composite Beams under Moving Distributed Masses

Directory of Open Access Journals (Sweden)

E. Bahmyari

2014-01-01

Full Text Available The dynamic response of laminated composite beams subjected to distributed moving masses is investigated using the finite element method (FEM based on the both first-order shear deformation theory (FSDT and the classical beam theory (CLT. Six and ten degrees of freedom beam elements are used to discretize the CLT and FSDT equations of motion, respectively. The resulting spatially discretized beam governing equations including the effect of inertial, Coriolis, and centrifugal forces due to moving distributed mass are evaluated in time domain by applying Newmark’s scheme. The presented approach is first validated by studying its convergence behavior and comparing the results with those of existing solutions in the literature. Then, the effect of incline angle, mass, and velocity of moving body, layer orientation, load length, and inertial, Coriolis, and centrifugal forces due to the moving distributed mass and friction force between the beam and the moving distributed mass on the dynamic behavior of inclined laminated composite beams are investigated.

Solid-Phase Immunoassay of Polystyrene-Encapsulated Semiconductor Coreshells for Cardiac Marker Detection

Directory of Open Access Journals (Sweden)

Sanghee Kim

2012-01-01

Full Text Available A solid-phase immunoassay of polystyrene-encapsulated semiconductor nanoparticles was demonstrated for cardiac troponin I (cTnI detection. CdSe/ZnS coreshells were encapsulated with a carboxyl-functionalized polystyrene nanoparticle to capture the target antibody through a covalent bonding and to eliminate the photoblinking and toxicity of semiconductor luminescent immunosensor. The polystyrene-encapsulated CdSe/ZnS fluorophores on surface-modified glass chip identified cTnI antigens at the level of ~ng/mL. It was an initial demonstration of diagnostic chip for monitoring a cardiovascular disease.

Fabrication of microlens and microlens array on polystyrene using CO 2 laser

KAUST Repository

Fan, Yiqiang

2011-11-01

This study presents a new process for fabricating microlens and microlens arrays directly on a surface of polystyrene using a CO2 laser. The working spot of the polystyrene is heated locally by a focused CO2 laser beam, which tends to have a hyperboloid profile due to the surface tension and can be used as a microlens. The microlenses with different dimensions were fabricated by changing the power of the laser beam. Microlens array was also fabricated with multiple scans of the laser beam on the polystyrene surface. © (2012) Trans Tech Publications, Switzerland.

Photooxidation of polystyrene: irradiation at 254 and 365 nm

International Nuclear Information System (INIS)

Otocka, E.P.; Curran, S.; Porter, R.S.

1983-01-01

Studies have been made of the near surface photooxidation of atactic polystyrene films prepared in the absence of air. The samples were photooxidized on exposure to air at two frequencies, 254 and 365 nm, using a calibrated mercury irradiation source with filters. Most studies were made at 40 0 C and as a function of irradiation time with the reactions characterized by changes in molecular weight and composition. The former was evaluated by gel permeation chromatography and the latter by transmission Fourier transform infrared ir spectroscopy and by multiple-internal-reflectance ir spectra using different angles and different crystals to evaluate compositions as a function of film depth. Species identified in photooxidation include the generation of hydroperoxides and the appearance of carbonyl bands with the latter identified by the spectral shift associated with the exposure of the photooxidized polystyrene surface to ammonia. These results suggest that principal products of near-surface oxidation of polystyrene are carboxylic acids. 6 figures, 1 table

Stress relaxation of bi-disperse polystyrene melts

DEFF Research Database (Denmark)

Hengeller, Ludovica; Huang, Qian; Dorokhin, Andriy

2016-01-01

We present start-up of uniaxial extension followed by stress relaxation experiments of a bi-disperse 50 % by weight blend of 95k and 545k molecular weight polystyrene. We also show, for comparison, stress relaxation measurements of the polystyrene melts with molecular weight 95k and 545k, which...... are the components of the bi-disperse melt. The measurements show three separated relaxation regimes: a fast regime, a transition regime, and a slow regime. In the fast regime, the orientation of the long chains is frozen and the stress relaxation is due to stretch relaxation of the short chains primarily....... Conversely in the slow regime, the long chains have retracted and undergo relaxation of orientation in fully relaxed short chains....

Foam supported sulfonated polystyrene as a new acidic material for catalytic reactions

NARCIS (Netherlands)

Ordomskiy, V.; Schouten, J.C.; Schaaf, van der J.; Nijhuis, T.A.

2012-01-01

Polystyrene was grafted on carbon foam with a melted polypropylene film predeposited on the surface. Polystyrene was subsequently sulfonated by chlorosulfonic acid. The effect of the temperature, time of grafting and concentration of radical initiator was studied. The materials were characterized by

Functionalized polystyrene nanoparticles as a platform for studying bio–nano interactions

Directory of Open Access Journals (Sweden)

Cornelia Loos

2014-12-01

Full Text Available Nanoparticles of various shapes, sizes, and materials carrying different surface modifications have numerous technological and biomedical applications. Yet, the mechanisms by which nanoparticles interact with biological structures as well as their biological impact and hazards remain poorly investigated. Due to their large surface to volume ratio, nanoparticles usually exhibit properties that differ from those of bulk materials. Particularly, the surface chemistry of the nanoparticles is crucial for their durability and solubility in biological media as well as for their biocompatibility and biodistribution. Polystyrene does not degrade in the cellular environment and exhibits no short-term cytotoxicity. Because polystyrene nanoparticles can be easily synthesized in a wide range of sizes with distinct surface functionalizations, they are perfectly suited as model particles to study the effects of the particle surface characteristics on various biological parameters. Therefore, we have exploited polystyrene nanoparticles as a convenient platform to study bio–nano interactions. This review summarizes studies on positively and negatively charged polystyrene nanoparticles and compares them with clinically used superparamagnetic iron oxide nanoparticles.

Application of polystyrene - water calorimeter in determination of absorbed dose. Vol. 4.

Energy Technology Data Exchange (ETDEWEB)

Soliman, F A [Nuclear Materials Authority, Maadi, Cairo (Egypt); Ashry, H A; El-Behay, A Z; Abdou, S [National Center, for Radiation Research and Technology, Atomic Energy Authority, Cairo (Egypt)

1996-03-01

The polystyrene-water calorimeter was investigated as a modification of the water calorimeter, where the polystyrene has a low specific heat and negligible known heat defect. This calorimeter was designed, constructed and calibrated for measurement of radiation absorbed dose. The system utilizes a thermistor to detect the radiation-induced temperature rise in the polystyrene absorber at certain point from the radiation source. A temperature stability of as low as 0.0018 degree C/min in a 42.0 degree C environment, and a gamma-radiation sensitivity of as high as 1.9720 ohm/Gy were obtained. Comparisons of the results obtained by using the polystyrene-water calorimeter with those obtained by applying other types of calorimeters i.e., water and graphite calorimeters were also done to aid in the possible realization of an accurate and efficient instrument for use under widely different irradiation conditions. 4 figs., 1 tab.

Fabrication of microlens and microlens array on polystyrene using CO 2 laser

KAUST Repository

Fan, Yiqiang; Li, Huawei; Foulds, Ian G.

2011-01-01

This study presents a new process for fabricating microlens and microlens arrays directly on a surface of polystyrene using a CO2 laser. The working spot of the polystyrene is heated locally by a focused CO2 laser beam, which tends to have a

Measurements of the electron dose distribution near inhomogeneities using a plastic scintillation detector

International Nuclear Information System (INIS)

Wells, C.M.M.; Mackie, T.R.; Podgorsak, M.B.; Holmes, M.A.; Papanikolaou, N.; Reckwerdt, P.J.; Cygler, J.; Rogers, D.W.O.; Bielajew, A.F.; Schmidt, D.G.

1994-01-01

Accurate measurement of the electron dose distribution near an inhomogeneity is difficult with traditional dosimeters which themselves perturb the electron field. The authors tested the performance of a new high resolution, water-equivalent plastic scintillation detector which has ideal properties for this application. A plastic scintillation detector with a 1 mm diameter, 3 mm long cylindrical sensitive volume was used to measure the dose distributions behind standard benchmark inhomogeneities in water phantoms. The plastic scintillator material is more water equivalent than polystyrene in terms of its mass collision stopping power and mass scattering power. Measurements were performed for beams of electrons having initial energies of 6 and 18 MeV at depths from 0.2-4.2 cm behind the inhomogeneities. The detector reveals hot and cold spots behind heterogeneities at resolutions equivalent to typical film digitizer spot sizes. Plots of the dose distributions behind air, aluminum, lead, and formulations for cortical and inner bone-equivalent materials are presented. The plastic scintillation detector is suited for measuring the electron dose distribution near an inhomogeneity. 14 refs., 9 figs

The jet mass distribution after Soft Drop

Energy Technology Data Exchange (ETDEWEB)

Marzani, Simone [Universita di Genova, Dipartimento di Fisica, Genoa (Italy); INFN, Sezione di Genova (Italy); Schunk, Lais [Deutsches Elektronen-Synchrotron DESY, Hamburg (Germany); Soyez, Gregory [IPhT, CEA Saclay, CNRS UMR 3681, Gif-Sur-Yvette (France)

2018-02-15

We present a first-principle computation of the mass distribution of jets which have undergone the grooming procedure known as Soft Drop. This calculation includes the resummation of the large logarithms of the jet mass over its transverse momentum, up to next-to-logarithmic accuracy, matched to exact fixed-order results at next-to-leading order. We also include non-perturbative corrections obtained from Monte-Carlo simulations and discuss analytic expressions for hadronisation and Underlying Event effects. (orig.)

The jet mass distribution after Soft Drop

Science.gov (United States)

Marzani, Simone; Schunk, Lais; Soyez, Gregory

2018-02-01

We present a first-principle computation of the mass distribution of jets which have undergone the grooming procedure known as Soft Drop. This calculation includes the resummation of the large logarithms of the jet mass over its transverse momentum, up to next-to-logarithmic accuracy, matched to exact fixed-order results at next-to-leading order. We also include non-perturbative corrections obtained from Monte-Carlo simulations and discuss analytic expressions for hadronisation and Underlying Event effects.

Effect of injection molded micro-structured polystyrene surfaces on proliferation of MC3T3-E1 cells

Directory of Open Access Journals (Sweden)

G. Lucchetta

2015-04-01

Full Text Available In this work, osteoinductive micro-pillared polystyrene surfaces were mass-produced for bone replacement applications, by means of the micro injection molding process. Firstly, the molding process parameters were optimized with a two-level, three-factor central composite face-centered plan to increase the quality of polystyrene micro pillars replication and to maximize the pillars height uniformity over the molded part. Secondly, osteoblastic MC3T3-E1 cells adhesion and proliferation on the replicated substrates were assessed as a function of micro topography parameters, such as pillars diameter, aspect ratio and spacing. Cell morphology and proliferation were evaluated through MTS test after 1, 3 and 7 days from seeding. The experimental results showed that cells adhesion and proliferation is more positively promoted on micro-pillared surfaces compared to flat surfaces, but no correlations were observed between cell proliferation and pillar diameter and spacing.

Mass Distribution in Rotating Thin-Disk Galaxies According to Newtonian Dynamics

Directory of Open Access Journals (Sweden)

James Q. Feng

2014-04-01

Full Text Available An accurate computational method is presented for determining the mass distribution in a mature spiral galaxy from a given rotation curve by applying Newtonian dynamics for an axisymmetrically rotating thin disk of finite size with or without a central spherical bulge. The governing integral equation for mass distribution is transformed via a boundary-element method into a linear algebra matrix equation that can be solved numerically for rotation curves with a wide range of shapes. To illustrate the effectiveness of this computational method, mass distributions in several mature spiral galaxies are determined from their measured rotation curves. All the surface mass density profiles predicted by our model exhibit approximately a common exponential law of decay, quantitatively consistent with the observed surface brightness distributions. When a central spherical bulge is present, the mass distribution in the galaxy is altered in such a way that the periphery mass density is reduced, while more mass appears toward the galactic center. By extending the computational domain beyond the galactic edge, we can determine the rotation velocity outside the cut-off radius, which appears to continuously decrease and to gradually approach the Keplerian rotation velocity out over twice the cut-off radius. An examination of circular orbit stability suggests that galaxies with flat or rising rotation velocities are more stable than those with declining rotation velocities especially in the region near the galactic edge. Our results demonstrate the fact that Newtonian dynamics can be adequate for describing the observed rotation behavior of mature spiral galaxies.

Absence of molecular deuterium dissociation during room-temperature permeation into polystyrene ICF target shells

International Nuclear Information System (INIS)

Honig, A.; Alexander, N.; Fan, Q.; Gram, R.; Kim, H.

1991-01-01

Polystyrene microshells filled with deuterium and tritium gas are important target shells for inertially confined fusion (ICF) and are particularly promising for target containing spin-polarized hydrogens fuels. A currently active approach to the latter uses polarized D in HD, in a method which requires preservation of the high purity of the initially prepared HD (very low specified H 2 and D 2 concentrations). This would not be possible if dissociation should occur during permeation into the target shells. We have thus tested polystyrene shells using a novel method which employs very pure polystyrene shells using a novel method which employs very pure ortho-D 2 as the test gas. An upper limit of 6 x 10 -4 was deduced for the dissociation of D 2 upon room temperature permeation through an approximately 8 um wall of polystyrene, clearing the way for use of polystyrene target shells for ICF fusion experiments with spin-polarized hydrogens fuels. 19 refs., 1 fig

Novel one-step route for synthesizing CdS/polystyrene nanocomposite hollow spheres.

Science.gov (United States)

Wu, Dazhen; Ge, Xuewu; Zhang, Zhicheng; Wang, Mozhen; Zhang, Songlin

2004-06-22

CdS/polystyrene nanocomposite hollow spheres with diameters between 240 and 500 nm were synthesized under ambient conditions by a novel microemulsion method in which the polymerization of styrene and the formation of CdS nanoparticles were initiated by gamma-irradiation. The product was characterized by transmission electron microscopy (TEM), field-emission scanning electron microscopy (FESEM), X-ray powder diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, and thermogravimetric analysis (TGA), which show the walls of the hollow spheres are porous and composed of polystyrene containing homogeneously dispersed CdS nanoparticles. The quantum-confined effect of the CdS/polystyrene nanocomposite hollow spheres is confirmed by the ultraviolet-visible (UV-vis) and photoluminescent (PL) spectra. We propose that the walls of these nanocomposite hollow spheres originate from the simultaneous synthesis of polystyrene and CdS nanoparticles at the interface of microemulsion droplets. This novel method is expected to produce various inorganic/polymer nanocomposite hollow spheres with potential applications in the fields of materials science and biotechnology.

A study of the effect of polystyrene sulfonation on the performance of terephthaloyl chloride-dihydroxydiphenyl sulfone copolymer/polystyrene system

Science.gov (United States)

Kahraman, R.; Kahn, K. A.; Ali, S. A.; Hamid, S. H.; Sahin, A. Z.

1998-12-01

Thermal, morphological, and mechanical properties of composites of a liquid crystalline copolymer (LCP) poly(terephthaloyl chloride)-co-(p,p’-dihydroxydiphenyl sulfone) with polystyrene (PS) and sulfonated polystyrene (SPS) are presented and discussed. Sulfonation of polystyrene was expected to improve the interfacial adhesion by introducing hydrogen bonding in the LCP/PS system. The degree of sulfonation was 11 %. The incompatibility (lack of proper interfacial adhesion) of the LCP/PS system resulted in sharp decrease in the composite tensile strength with LCP addition. The performance of the system did not change when processed at a higher temperature (270 °C instead of 225 °C). While a composite plate of 25% LCP/PS could not be fabricated, it was possible for LCP/SPS (processed at 215 °C), indicating some improvement in interfacial bonding by sulfonation. Sulfonation of PS resulted in fracture with some degree of plastic deformation for pure SPS matrix and also the LCP/SPS system with the lowest LCP content (1 wt%), whereas plastic deformation was not observed for PS used as received. The strength of the LCP/SPS system also decreased with increase in LCP content, indicating that 11% sulfonation is not sufficient to introduce significant compatibility, but it was not as dramatic as that for LCP/PS. The performance of the LCP/SPS system was not affected significantly by heat treatment at the process temperature.

Dynamical Mass Measurements of Contaminated Galaxy Clusters Using Support Distribution Machines

Science.gov (United States)

Ntampaka, Michelle; Trac, Hy; Sutherland, Dougal; Fromenteau, Sebastien; Poczos, Barnabas; Schneider, Jeff

2018-01-01

We study dynamical mass measurements of galaxy clusters contaminated by interlopers and show that a modern machine learning (ML) algorithm can predict masses by better than a factor of two compared to a standard scaling relation approach. We create two mock catalogs from Multidark’s publicly available N-body MDPL1 simulation, one with perfect galaxy cluster membership infor- mation and the other where a simple cylindrical cut around the cluster center allows interlopers to contaminate the clusters. In the standard approach, we use a power-law scaling relation to infer cluster mass from galaxy line-of-sight (LOS) velocity dispersion. Assuming perfect membership knowledge, this unrealistic case produces a wide fractional mass error distribution, with a width E=0.87. Interlopers introduce additional scatter, significantly widening the error distribution further (E=2.13). We employ the support distribution machine (SDM) class of algorithms to learn from distributions of data to predict single values. Applied to distributions of galaxy observables such as LOS velocity and projected distance from the cluster center, SDM yields better than a factor-of-two improvement (E=0.67) for the contaminated case. Remarkably, SDM applied to contaminated clusters is better able to recover masses than even the scaling relation approach applied to uncon- taminated clusters. We show that the SDM method more accurately reproduces the cluster mass function, making it a valuable tool for employing cluster observations to evaluate cosmological models.

Effect of distributive mass of spring on power flow in engineering test

Science.gov (United States)

Sheng, Meiping; Wang, Ting; Wang, Minqing; Wang, Xiao; Zhao, Xuan

2018-06-01

Mass of spring is always neglected in theoretical and simulative analysis, while it may be a significance in practical engineering. This paper is concerned with the distributive mass of a steel spring which is used as an isolator to simulate isolation performance of a water pipe in a heating system. Theoretical derivation of distributive mass effect of steel spring on vibration is presented, and multiple eigenfrequencies are obtained, which manifest that distributive mass results in extra modes and complex impedance properties. Furthermore, numerical simulation visually shows several anti-resonances of the steel spring corresponding to impedance and power flow curves. When anti-resonances emerge, the spring collects large energy which may cause damage and unexpected consequences in practical engineering and needs to be avoided. Finally, experimental tests are conducted and results show consistency with that of the simulation of the spring with distributive mass.

Low-voltage bendable pentacene thin-film transistor with stainless steel substrate and polystyrene-coated hafnium silicate dielectric.

Science.gov (United States)

Yun, Dong-Jin; Lee, Seunghyup; Yong, Kijung; Rhee, Shi-Woo

2012-04-01

The hafnium silicate and aluminum oxide high-k dielectrics were deposited on stainless steel substrate using atomic layer deposition process and octadecyltrichlorosilane (OTS) and polystyrene (PS) were treated improve crystallinity of pentacene grown on them. Besides, the effects of the pentacene deposition condition on the morphologies, crystallinities and electrical properties of pentacene were characterized. Therefore, the surface treatment condition on dielectric and pentacene deposition conditions were optimized. The pentacene grown on polystyrene coated high-k dielectric at low deposition rate and temperature (0.2-0.3 Å/s and R.T.) showed the largest grain size (0.8-1.0 μm) and highest crystallinity among pentacenes deposited various deposition conditions, and the pentacene TFT with polystyrene coated high-k dielectric showed excellent device-performance. To decrease threshold voltage of pentacene TFT, the polystyrene-thickness on high-k dielectric was controlled using different concentration of polystyrene solution. As the polystyrene-thickness on hafnium silicate decreases, the dielectric constant of polystyrene/hafnium silicate increases, while the crystallinity of pentacene grown on polystyrene/hafnium silicate did not change. Using low-thickness polystyrene coated hafnium silicate dielectric, the high-performance and low voltage operating (pentacene thin film transistor (μ: ~2 cm(2)/(V s), on/off ratio, >1 × 10(4)) and complementary inverter (DC gains, ~20) could be fabricated.

A rationale for continuing mass antibiotic distributions for trachoma

Directory of Open Access Journals (Sweden)

House Jenafir

2007-08-01

Full Text Available Abstract Background The World Health Organization recommends periodic mass antibiotic distributions to reduce the ocular strains of chlamydia that cause trachoma, the world's leading cause of infectious blindness. Their stated goal is to control infection, not to completely eliminate it. A single mass distribution can dramatically reduce the prevalence of infection. However, if infection is not eliminated in every individual in the community, it may gradually return back into the community, so often repeated treatments are necessary. Since public health groups are reluctant to distribute antibiotics indefinitely, we are still in need of a proven long-term rationale. Here we use mathematical models to demonstrate that repeated antibiotic distributions can eliminate infection in a reasonable time period. Methods We fit parameters of a stochastic epidemiological transmission model to data collected before and 6 months after a mass antibiotic distribution in a region of Ethiopia that is one of the most severely affected areas in the world. We validate the model by comparing our predicted results to Ethiopian data which was collected biannually for two years past the initial mass antibiotic distribution. We use the model to simulate the effect of different treatment programs in terms of local elimination of infection. Results Simulations show that the average prevalence of infection across all villages progressively decreases after each treatment, as long as the frequency and coverage of antibiotics are high enough. Infection can be eliminated in more villages with each round of treatment. However, in the communities where infection is not eliminated, it returns to the same average level, forming the same stationary distribution. This phenomenon is also seen in subsequent epidemiological data from Ethiopia. Simulations suggest that a biannual treatment plan implemented for 5 years will lead to elimination in 95% of all villages. Conclusion Local

A rationale for continuing mass antibiotic distributions for trachoma.

Science.gov (United States)

Ray, Kathryn J; Porco, Travis C; Hong, Kevin C; Lee, David C; Alemayehu, Wondu; Melese, Muluken; Lakew, Takele; Yi, Elizabeth; House, Jenafir; Chidambaram, Jaya D; Whitcher, John P; Gaynor, Bruce D; Lietman, Thomas M

2007-08-07

The World Health Organization recommends periodic mass antibiotic distributions to reduce the ocular strains of chlamydia that cause trachoma, the world's leading cause of infectious blindness. Their stated goal is to control infection, not to completely eliminate it. A single mass distribution can dramatically reduce the prevalence of infection. However, if infection is not eliminated in every individual in the community, it may gradually return back into the community, so often repeated treatments are necessary. Since public health groups are reluctant to distribute antibiotics indefinitely, we are still in need of a proven long-term rationale. Here we use mathematical models to demonstrate that repeated antibiotic distributions can eliminate infection in a reasonable time period. We fit parameters of a stochastic epidemiological transmission model to data collected before and 6 months after a mass antibiotic distribution in a region of Ethiopia that is one of the most severely affected areas in the world. We validate the model by comparing our predicted results to Ethiopian data which was collected biannually for two years past the initial mass antibiotic distribution. We use the model to simulate the effect of different treatment programs in terms of local elimination of infection. Simulations show that the average prevalence of infection across all villages progressively decreases after each treatment, as long as the frequency and coverage of antibiotics are high enough. Infection can be eliminated in more villages with each round of treatment. However, in the communities where infection is not eliminated, it returns to the same average level, forming the same stationary distribution. This phenomenon is also seen in subsequent epidemiological data from Ethiopia. Simulations suggest that a biannual treatment plan implemented for 5 years will lead to elimination in 95% of all villages. Local elimination from a community is theoretically possible, even in the

Separation of transfer ribonucleic acids on polystyrene anion exchangers

Energy Technology Data Exchange (ETDEWEB)

Singhal, R.P.; Griffin, G.D.; Novelli, G.D.

1976-11-16

The transfer RNA separation by chromatography on strong-base-polystyrene exchange materials is examined and compared with the widely used reversed-phase chromatography. Results indicate important differences in some transfer RNA (tRNA) elution patterns by the anion-exchange chromatography, as compared with the reversed-phase chromatography. Transfer RNAs containing hydrophobic groups are adsorbed more strongly. The anion exchanger has twice the number of theoretical plates. Single peaks of tRNA/sub 2//sup Glu/ and tRNA/sub 1//sup Phe/ obtained from the reversed-phase column give multiple peaks on polystyrene anion-exchange chromatography. All six leucine tRNAs (Escherichia coli) and differences in tRNA populations synthesized during early and late stages of the dividing lymphocytes from normal human blood can be characterized by the anion-exchange chromatography. Different separation profiles are obtained by two separation systems for tyrosine tRNAs from mouse liver and mouse-plasma-cell tumor. The results indicate that, in contrast to the reversed-phase chromatography, strong-base-polystyrene anion-exchange chromatography is capable of separating tRNAs with minor structural differences.

High impact polystyrene (HIPS). Predicting its molecular, morphological and mechanical properties

International Nuclear Information System (INIS)

Luciani, C; Estenoz, D; Morales, G; Meira, G

2004-01-01

A mathematical model that is able to predict the molecular and morphological structure of high impact polystyrene (HIPS) and the Fluidity Index (MFI) is presented. The model is divided into two parts: a) the estimation of the material's molecular and morphological properties, simulating the polymerization process in discontinuous mass based on the recipe and the conditions of synthesis; and b) the prediction of rheological variables (viscosity at low deformation speeds and relaxation time), and of the MFI, based on average molecular and morphological variables. The model also combines with empirical correlations proposed in the literature [1] in order to estimate impact strength (IS). The predictions for a), b) and impact strength were co-validated by independent data and resulted in a good fit (CW)

Coupling of carboxylic groups onto the surface of polystyrene parts during fused filament fabrication

Science.gov (United States)

Nagel, Jürgen; Zimmermann, Philipp; Schubert, Oliver; Simon, Frank; Schlenstedt, Kornelia

2017-11-01

A method for the fabrication of polystyrene parts, modified with carboxylic groups during Fused Filament Fabrication (FFF), is being introduced. This method is based on the application of a thin layer of a reactive polymer carrying carboxylic groups on a substrate surface. A polystyrene film is printed on top of this layer. During contact between the hot melt and the reactive layer, a Friedel-Crafts type acylation using a green catalyst takes place, which attaches the reactive polymer to the polystyrene surface. The modified surface is homogeneous, hydrophilic and able to bind copper ions. The method could be used to fabricate unique parts of polystyrene with tailored surface functionalisation. It could be applied for laboratory use, e.g. for the manufacture of lab-on-a-chip devices.

Effect of salivary secretory IgA on the adhesion of Candida albicans to polystyrene.

Science.gov (United States)

San Millán, R; Elguezabal, N; Regúlez, P; Moragues, M D; Quindós, G; Pontón, J

2000-09-01

Attachment of Candida albicans to plastic materials of dental prostheses or to salivary macromolecules adsorbed on their surface is believed to be a critical event in the development of denture stomatitis. In an earlier study, it was shown that adhesion of C. albicans to polystyrene, a model system to study the adhesion of C. albicans to plastic materials, can be partially inhibited with an mAb directed against cell wall polysaccharides of C. albicans. In the present study, the role of whole saliva in the adhesion of C. albicans to polystyrene has been investigated, and three mAbs directed against epitopes of cell wall mannoproteins have been used to mimic the inhibitory effect observed with salivary secretory IgA (sIgA) on the adhesion of C. albicans to polystyrene. In the absence of whole saliva, adherence of C. albicans 3153 increased with germination. However, the presence of whole saliva enhanced the adhesion to polystyrene of C. albicans 3153 yeast cells but decreased the adhesion of germinated cells. The enhancement of adhesion of yeast cells to polystyrene mediated by saliva was confirmed with an agerminative mutant of C. albicans 3153. The inhibition of the adhesion of C. albicans 3153 germ tubes to polystyrene was due to the salivary sIgA since sIgA-depleted saliva enhanced the adhesion of C. albicans 3153 to polystyrene. The inhibitory effect mediated by sIgA was not related to the inhibition of germination but to the blockage of adhesins expressed on the cell wall surface of the germ tubes. The three mAbs studied reduced the adhesion of C. albicans 3153 to polystyrene at levels equivalent to those for purified sIgA. The highest reduction in the adhesion was obtained with the IgA mAb N3B. The best results were obtained when the three mAbs were combined. The results suggest that whole saliva plays a different role in the adhesion of C. albicans to polystyrene depending on the morphological phase of C. albicans. These results may give new insights into the

Stereoselective Copolymerization of Styrene with Terpenes Catalyzed by an Ansa-Lanthanidocene Catalyst: Access to New Syndiotactic Polystyrene-Based Materials

Directory of Open Access Journals (Sweden)

Eva Laur

2017-11-01

Full Text Available The copolymerization of bio-renewable β-myrcene or β-farnesene with styrene was examined using an ansa-neodymocene catalyst, affording two series of copolymers with high styrene content and unprecedented syndioregularity of the polystyrene sequences. The incorporation of terpene in the copolymers ranged from 5.6 to 30.8 mol % (β-myrcene and from 2.5 to 9.8 mol % (β-farnesene, respectively. NMR spectroscopy and DSC analyses suggested that the microstructure of the copolymers consists of 1,4- and 3,4-poly(terpene units randomly distributed along syndiotactic polystyrene chains. The thermal properties of the copolymers are strongly dependent on the terpene content, which is easily controlled by the initial feed. The terpolymerization of styrene with β-myrcene in the presence of ethylene was also examined.

Differential distributions for top-quark hadro-production with a running mass

International Nuclear Information System (INIS)

Dowling, M.; Moch, S.; Hamburg Univ.

2013-05-01

We take a look at how the differential distributions for top-quark production are affected by changing to the running mass scheme. Specifically we consider the transverse momentum, rapidity and pair-invariant mass distributions at NLO for the top-quark mass in the MS scheme. It is found that, similar to the total cross section, the perturbative expansion converges faster and the scale dependence improves using the mass in the MS scheme as opposed to the on-shell scheme. We also update the analysis for the total cross section using the now available full NNLO contribution.

Differential distributions for top-quark hadro-production with a running mass

Energy Technology Data Exchange (ETDEWEB)

Dowling, M. [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Moch, S. [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Hamburg Univ. (Germany). 2. Inst. fuer Theoretische Physik

2013-05-15

We take a look at how the differential distributions for top-quark production are affected by changing to the running mass scheme. Specifically we consider the transverse momentum, rapidity and pair-invariant mass distributions at NLO for the top-quark mass in the MS scheme. It is found that, similar to the total cross section, the perturbative expansion converges faster and the scale dependence improves using the mass in the MS scheme as opposed to the on-shell scheme. We also update the analysis for the total cross section using the now available full NNLO contribution.

Preparation of Track Etch Membrane Filters Using Polystyrene Film

International Nuclear Information System (INIS)

Kaewsaenee, Jerawut; Ratanatongchai, Wichian; Supaphol, Pitt; Visal-athaphand, Pinpan

2007-08-01

Full text: Polystyrene nuclear track etch membrane filters was prepared by exposed 13 .m thin film polystyrene with fission fragment. Nuclear latent track was enlarged to through hole on the film by etching with 80 o C 40% H 2 SO 4 with K 2 Cr 2 O 7 solution for 6-10 hour. The hole size was depend on concentration of etching solution and etching time with 1.3-3.4 .m hole diameter. The flow rate test of water was 0.79-1.56 mm cm-2 min-1 at 109.8-113.7 kPa pressure

Trichomonas vaginalis clinical isolates: cytoadherence and adherence to polystyrene, intrauterine device, and vaginal ring.

Science.gov (United States)

Dos Santos, Odelta; Rigo, Graziela Vargas; Macedo, Alexandre José; Tasca, Tiana

2017-12-01

The parasitism by Trichomonas vaginalis is complex and in part is mediated by cytoadherence accomplished via five surface proteins named adhesins and a glycoconjugate called lipophosphoglycan (TvLPG). In this study, we evaluated the ability of T. vaginalis isolates to adhere to cells, plastic (polystyrene microplates), intrauterine device (IUD), and vaginal ring. Of 32 T. vaginalis isolates, 4 (12.5%) were strong adherent. The T. vaginalis isolates TV-LACM6 and TV-LACM14 (strong polystyrene-adherent) were also able to adhere to IUD and vaginal ring. Following chemical treatments, results demonstrated that the T. vaginalis components, lipophosphoglycan, cytoskeletal proteins, and surface molecules, were involved in both adherence to polystyrene and cytoadherence. The gene expression level from four adhesion proteins was highest in trophozoites adhered to cells than trophozoites adhered to the abiotic surface (polystyrene microplate). Our data indicate the major involvement of TvLPG in adherence to polystyrene, and that adhesins are important for cytoadherence. Furthermore, to our knowledge, this is the first report showing the T. vaginalis adherence to contraceptive devices, reaffirming its importance as pathogen among women in reproductive age.

Effect of Surface Modification of Nanosilica on the Viscoelastic Properties of Its Polystyrene Nanocomposite

Directory of Open Access Journals (Sweden)

M. Mortezaei

2008-12-01

Full Text Available The preparation and characterization of the vinyltriethoxysilane-modified silica nanoparticles were investigated. Also the surface tension of polystyrene, native (hydrophilic silica and silane-modified (hydrophobic silica were determined. Two kinds of polystyrene/silica (treated and non-treated nanocomposites were prepared with different filler loadings by solution method. Their viscoelastic properties were studied by dynamic stress controlled rotary shear rheometer. Solid-like response of polystyrene/native silica nanocomposites were observed in the terminal zone. Solid inclusionsincrease the storage modulus more than the loss modulus, hence decrease the material damping. By increasing filler volume fraction, the particles tend to agglomerate and build clusters. The presence of clusters increases the viscosity, the moduli and the viscoelastic non-linearity of the composites.Treating the filler surface reduces its tendency to agglomerate as well as the adhesion between the particles and the polystyrene, leading to lower viscosity and interfacial slippage. Also the loss modulus peak is affected significantly by the particle surface area and its surface property in silica-filled polystyrene, which corresponds to its glass transition.

Non-aqueous retention measurement: ultrafiltration behaviour of polystyrene solutions and colloidal silver particles

NARCIS (Netherlands)

Beerlage, M.A.M.; Beerlage, M.A.M.; Heijnen, M.L.; Mulder, M.H.V.; Smolders, C.A.; Smolders, C.A.; Strathmann, H.

1996-01-01

The retention behaviour of polyimide ultrafiltration membranes was investigated using dilute solutions of polystyrene in ethyl acetate as test solutions. It is shown that flow-induced deformation of the polystyrene chains highly affects the membrane retention. This coil-stretch transition is not

Hydrophilic nanoporous polystyrenes and 1,2-polybutadienes

DEFF Research Database (Denmark)

Guo, Fengxiao; Jankova Atanasova, Katja; Vigild, Martin Etchells

2008-01-01

Nanoporous polymers from ordered block copolymers having hydrophilic cavity surfaces were successfully prepared by two methodologies: ' 1. Nanoporous polystyrenes fromPtBA-b-PS diblock or PDMS-b-PtBA-b-PS triblock copolymer precursors by atom transfer radical polymerization (ATRP), or combination...... of living anionic polymerization~ and ATRP r~spectively. The one, PtBA block, can be modified to the hydrophilic PAA, where the dther, polydimethysiloxane (PDMS) block, can be fully degraded. Deprotection of the tert-butyl groups in PtBA and the selective etching of PDMS· chains were accomplished...... by applying HF or TFA in one step. Thus both the di- and triblock copolymers after such a treatment resulted. in nanoporous polystyrenes with hexagonal cavities of different nanosizes (6-11 nm, Figure 1). 2. Nanoporous I,2-polybutadienes (I,2-PB) by grafting various acrylic monomers onto the pore. surfaces...

Magnetic properties of Fe-oxide and (Fe, Co) oxide nanoparticles synthesized in polystyrene resin matrix

Science.gov (United States)

Rodak, D.; Kroll, E.; Tsoi, G. M.; Vaishnava, P. P.; Naik, R.; Wenger, L. E.; Suryanarayanan, R.; Naik, V. M.; Boolchand, P.

2003-03-01

Magnetic nanoparticles have potential applications ranging from drug delivery and imaging in the medical field to sensing and memory storage in technology. The preparation, structure, and physical properties of iron oxide-based nanoparticles synthesized by ion exchange in a polystyrene resin matrix have been investigated. Employing a synthesis method developed originally by Ziolo, et. al^1, nanoparticles were prepared in a sulfonated divinyl benzene polystyrene resin matrix using various aqueous solutions of (1) FeCl_2, (2) FeCl_3, (3) FeCl2 : 2FeCl3 , (4) 9FeCl2 : CoCl_2, and (5) 4FeCl2 : CoCl_2. Powder x-ray diffraction measurements were used to identify the phases present while transmission electron microscopy was used for particle size distribution determinations. SQUID magnetization measurements (field-cooled and zero-field-cooled) and Fe^57 Mössbauer effect measurements indicate the presence of ferromagnetic iron oxide phases and a superparamagnetic behavior with blocking temperatures (T_B) varying from 50 K to room temperature. Nanoparticles synthesized using a stoichiometric mixture of FeCl2 and FeCl3 exhibit the lowest TB and smallest particle size distribution. The Mössbauer effect measurements have also been used to identify the iron oxides phases present and their relative amounts in the nanoparticles ^1R.F. Ziolo, et al., Science 207, 219 (1992). *Permanent address: Kettering University, Flint, MI 48504

The properties of the wood-polystyrene interphase determined by inverse gas chromatography

Science.gov (United States)

John Simonsen; Zhenqiu Hong; Timothy G. Rials

1997-01-01

The properties of the interphase in wood-polymer composites are important determinants of the properties of the final composite. This study used inverse gas chromatography (IGC) to measure interphasal properties of composites of polystyrene and two types of wood fiber fillers and an inoranic substrate (CW) with varying amounts of surface coverage of polystyrene. Glass...

Attitude dynamics and control of a spacecraft using shifting mass distribution

Science.gov (United States)

Ahn, Young Tae

Spacecraft need specific attitude control methods that depend on the mission type or special tasks. The dynamics and the attitude control of a spacecraft with a shifting mass distribution within the system are examined. The behavior and use of conventional attitude control actuators are widely developed and performing at the present time. However, the advantage of a shifting mass distribution concept can complement spacecraft attitude control, save mass, and extend a satellite's life. This can be adopted in practice by moving mass from one tank to another, similar to what an airplane does to balance weight. Using this shifting mass distribution concept, in conjunction with other attitude control devices, can augment the three-axis attitude control process. Shifting mass involves changing the center-of-mass of the system, and/or changing the moments of inertia of the system, which then ultimately can change the attitude behavior of the system. This dissertation consists of two parts. First, the equations of motion for the shifting mass concept (also known as morphing) are developed. They are tested for their effects on attitude control by showing how shifting the mass changes the spacecraft's attitude behavior. Second, a method for optimal mass redistribution is shown using a combinatorial optimization theory under constraints. It closes with a simple example demonstrating an optimal reconfiguration. The procedure of optimal reconfiguration from one mass distribution to another to accomplish attitude control has been demonstrated for several simple examples. Mass shifting could work as an attitude controller for fine-tuning attitude behavior in small satellites. Various constraints can be applied for different situations, such as no mass shift between two tanks connected by a failed pipe or total amount of shifted mass per pipe being set for the time optimum solution. Euler angle changes influenced by the mass reconfiguration are accomplished while stability

Unexplained structure in (μ,π) invariant mass distribution

International Nuclear Information System (INIS)

Ramm, C.A.

2000-01-01

Structures in invariant mass distributions from (μ,π) combinations in the range 0.380 μ -π 0.470 GeV from neutrino and kaon experiments are presented in comparable formats. No artifacts have been found to account for any part of the structure. Hypotheses that the similarities are due to recurrent statistical fluctuations are beyond credibility. My conclusion is that the similarities are overwhelming evidence that the structure is of an unexplained physical origin. It includes an enhancement which would accord with the decay of a narrow (μ,π) state of mass 0.429 GeV. The purpose of this report is to request and enable every experimenter with precise M μ , π distributions to investigate their degree of correspondence with these analyses (author)

Colonic necrosis due to calcium polystyrene sulfonate (Kalimate not suspended in sorbitol

Directory of Open Access Journals (Sweden)

María Dolores Castillo-Cejas

2013-04-01

Full Text Available Cation-exchange resins are used in the management of hyperkalemia, particularly in patients with end-stage renal disease. These resins were associated with gastrointestinal tract lesions, especially sodium polystyrene sulfonate (Kayexalate mixed with sorbitol. We present a case of colonic necrosis after the administration of calcium polystyrene sulfonate (Kalimate not suspended in sorbitol.

APPLICATION OF POLYSTYRENE FOAM CORE FUSIBLE PATTERNS IN PRODUCTION OF GAS TURBINES’ CAST PARTS

Directory of Open Access Journals (Sweden)

O. I. Shinsky

2016-01-01

Full Text Available The task of replacing the LVM dissolves polystyrene molding on models is at the present time, technologically, economically and environmentally promising from the point of view of industrial applications for gas turbine plants in Ukraine. The authors proposed and tested manufacturing process of casting ceramic molds way to remove the polystyrene model of the dissolution of her organic solvents. Kinetic parameters of the process of dissolving and removing patterns of degradation products the polystyrene in the group of solvents depending on the type and amount of polystyrene were identified. The absence of surface defects of castings, reduction of roughness, increased their accuracy class in comparison to accepted technological regulations of the process of production, which reduced the cost of machined parts and increased utilization of expensive heat-resistant alloys were produced.

Gas puff radiation performance as a function of radial mass distribution

International Nuclear Information System (INIS)

Coleman, Philip L.; Krishnan, Mahadevan; Prasad, Rahul; Qi, Niansheng; Waisman, Eduardo; Failor, B.H.; Levine, J.S.; Sze, H.

2002-01-01

The basic concept of a z-pinch, that JxB forces implode a shell of mass, creating a hot dense plasma on-axis, is coming under closer scrutiny. Wire arrays may start with an initial cold mass in a near 'ideal' shell, but in fact they appear to develop complex radial mass distributions well before the final x-ray output. We consider here the situation for gas puff z-pinches. While the ideal of a gas 'shell' has been the nominal objective for many years, detailed measurements of gas flow show that nozzles used for plasma radiation sources (PRS) also have complex radial distributions. In particular, there are significant data showing that the best x-ray yield comes from the least shell-like distributions. Recent experiments on the Double Eagle generator with argon have further enhanced this view. For those tests with a double 'shell' nozzle, there was a factor of almost 4 increase in yield when the relative mass (outer:inner) in the two shells was changed from 2:1 to less than 1:1. We suggest the following explanation. A configuration with most of its mass at large radii is subject to severe disruption by instabilities during the implosion. A more continuous radial mass distribution with dρ/dr < 0 may mitigate instability development (via the 'snowplow stabilization' mechanism) and thus enhance the thermalization of the kinetic energy of the imploding mass. In addition, the appropriate balance of outer to inner mass maximizes the formation of a strong shock in the core of the pinch that heats the plasma and leads to x-ray emission

THE DEPENDENCE OF PRESTELLAR CORE MASS DISTRIBUTIONS ON THE STRUCTURE OF THE PARENTAL CLOUD

International Nuclear Information System (INIS)

Parravano, Antonio; Sánchez, Néstor; Alfaro, Emilio J.

2012-01-01

The mass distribution of prestellar cores is obtained for clouds with arbitrary internal mass distributions using a selection criterion based on the thermal and turbulent Jeans mass and applied hierarchically from small to large scales. We have checked this methodology by comparing our results for a log-normal density probability distribution function with the theoretical core mass function (CMF) derived by Hennebelle and Chabrier, namely a power law at large scales and a log-normal cutoff at low scales, but our method can be applied to any mass distributions representing a star-forming cloud. This methodology enables us to connect the parental cloud structure with the mass distribution of the cores and their spatial distribution, providing an efficient tool for investigating the physical properties of the molecular clouds that give rise to the prestellar core distributions observed. Simulated fractional Brownian motion (fBm) clouds with the Hurst exponent close to the value H = 1/3 give the best agreement with the theoretical CMF derived by Hennebelle and Chabrier and Chabrier's system initial mass function. Likewise, the spatial distribution of the cores derived from our methodology shows a surface density of companions compatible with those observed in Trapezium and Ophiucus star-forming regions. This method also allows us to analyze the properties of the mass distribution of cores for different realizations. We found that the variations in the number of cores formed in different realizations of fBm clouds (with the same Hurst exponent) are much larger than the expected root N statistical fluctuations, increasing with H.

Production and testing of 244Cm-labeled fluorescent polystyrene latex microspheres

International Nuclear Information System (INIS)

Guilmette, R.A.; Mueller, H.L.; Brodbeck, R.D.

1988-01-01

To provide a useful tool for studying the mechanisms of retention and translocation of respirable-sized, alpha-emitting particles, we have developed a method of incorporating 244 Cm into fluorescent polystyrene latex microspheres. The resultant particles contain alpha radioactivity comparable to μm-size (AMAD) 239 Pu0 2 particles, but are easily visible by fluorescent light microscopy. Preliminary testing of the particles with dog macrophages in vitro has shown that the initial uptake of these Cm-labeled particles is more rapid than uptake of unlabeled particles of similar size. We are continuing to develop procedures for achieving better particle yields, smaller dispersity of particle size distributions and improved retention of the Cm label by the particles. (author)

Preparation of polystyrene brush film by radical chain-transfer polymerization and micromechanical properties

Energy Technology Data Exchange (ETDEWEB)

Zhao Jing [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Graduate School of Chinese Academy of Sciences, Beijing 100039 (China); Chen Miao [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China)], E-mail: miaochen99@yahoo.com; An Yanqing [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Graduate School of Chinese Academy of Sciences, Beijing 100039 (China); Liu Jianxi [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Yan Fengyuan [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China)], E-mail: fyyan@lzb.ac.cn

2008-12-30

A radical chain-transfer polymerization technique has been applied to graft-polymerize brushes of polystyrene (PSt) on single-crystal silicon substrates. 3-Mercapto-propyltrimethoxysilane (MPTMS), as a chain-transfer agent for grafting, was immobilized on the silicon surface by a self-assembling process. The structure and morphology of the graft-functionalized silicon surfaces were characterized by the means of contact-angle measurement, ellipsometric thickness measurement, Fourier transformation infrared (FTIR) spectroscopy, and atomic force microscopy (AFM). The nanotribological and micromechanical properties of the as-prepared polymer brush films were investigated by frictional force microscopy (FFM), force-volume analysis and scratch test. The results indicate that the friction properties of the grafted polymer films can be improved significantly by the treatment of toluene, and the chemically bonded polystyrene film exhibits superior scratch resistance behavior compared with the spin-coated polystyrene film. The resultant polystyrene brush film is expected to develop as a potential lubrication coating for microelectromechanical systems (MEMS)

submitter Preparation and luminescence properties of ZnO:Ga – polystyrene composite scintillator

CERN Document Server

Burešová, Hana; Turtos, Rosana Martinez; Jarý, Vítězslav; Mihóková, Eva; Beitlerová, Alena; Pjatkan, Radek; Gundacker, Stefan; Auffray, Etiennette; Lecoq, Paul; Nikl, Martin; Čuba, Václav

2016-01-01

Highly luminescent ZnO:Ga-polystyrene composite (ZnO:Ga-PS) with ultrafast subnanosecond decay was prepared by homogeneous embedding the ZnO:Ga scintillating powder into the scintillating organic matrix. The powder was prepared by photo-induced precipitation with subsequent calcination in air and Ar/H2 atmospheres. The composite was subsequently prepared by mixing the ZnO:Ga powder into the polystyrene (10 wt% fraction of ZnO:Ga) and press compacted to the 1 mm thick pellet. Luminescent spectral and kinetic characteristics of ZnO:Ga were preserved. Radioluminescence spectra corresponded purely to the ZnO:Ga scintillating phase and emission of polystyrene at 300-350 nm was absent. These features suggest the presence of non-radiative energy transfer from polystyrene host towards the ZnO:Ga scintillating phase which is confirmed by the measurement of X-ray excited scintillation decay with picosecond time resolution. It shows an ultrafast rise time below the time resolution of the experiment (18 ps) and a single-...

Patient distribution in a mass casualty event of an airplane crash

NARCIS (Netherlands)

Postma, Ingri L. E.; Weel, Hanneke; Heetveld, Martin J.; van der Zande, Ineke; Bijlsma, Taco S.; Bloemers, Frank W.; Goslings, J. Carel

2013-01-01

Difficulties have been reported in the patient distribution during Mass Casualty Incidents. In this study we analysed the regional patient distribution protocol (PDP) and the actual patient distribution after the 2009 Turkish Airlines crash near Amsterdam. Analysis of the patient distribution of 126

IDENTIFICATION OF THE MASS DISTRIBUTIONS OF THE MILK FAT PHASE USING UNIVERSAL PEARSON DISTRIBUTIONS

Directory of Open Access Journals (Sweden)

A. A. Khvostov

2015-01-01

Full Text Available In this paper we consider the problem of approximating the experimental values of the coefficient of attenuation of ultrasonic oscillations and the mass distribution of the fat globules in the milk and milk products. The analysis of experimental data in terms of the choice of the method of approximation was done. A approximating dependence is based on the solution of Pearson differential equations. The advantages of the proposed method for the type of approximation of the experimental data obtained. An algorithm for constructing a mathematical model describing the relaxation spectrum and mass distribution of the fat globules in the milk and milk products was implemented. As a result, a family of Pearson approximation curves of the experimental data shows the ability to qualitatively correctly describe the change in the distribution of the fat phase in the process of homogenization. It estimates the error of approximating dependence, which amounted to 18 %. It is shown that during of the process of homogenization of dairy products changes shape of the curve describing the distribution of the fat globules, in view of the fact that there is a local extremum, caused by the presence of the non-homogenized fat globules. The accuracy of the selected mathematical model is significantly reduced. At the same time, it loses its physical meaning and its parameters. To address the identified deviations in the proposed mass distribution of fat globules as a function with two modes. It is proved that the complexity of the model is not only doubles the number of its parameters, but also complicates the interpretation of measurement results in a control system, and makes it difficult to analyze the obtained parameters of approximation by decision-maker. As a result of approximation of experimental data suggested to use statistical moments of the distribution for problem decision.

Polystyrene Based Silver Selective Electrodes

Directory of Open Access Journals (Sweden)

Shiva Agarwal

2002-06-01

Full Text Available Silver(I selective sensors have been fabricated from polystyrene matrix membranes containing macrocycle, Me6(14 diene.2HClO4 as ionophore. Best performance was exhibited by the membrane having a composition macrocycle : Polystyrene in the ratio 15:1. This membrane worked well over a wide concentration range 5.0×10-6–1.0×10-1M of Ag+ with a near-Nernstian slope of 53.0 ± 1.0 mV per decade of Ag+ activity. The response time of the sensor is <15 s and the membrane can be used over a period of four months with good reproducibility. The proposed electrode works well in a wide pH range 2.5-9.0 and demonstrates good discriminating power over a number of mono-, di-, and trivalent cations. The sensor has also been used as an indicator electrode in the potentiometric titration of silver(II ions against NaCl solution. The sensor can also be used in non-aqueous medium with no significant change in the value of slope or working concentration range for the estimation of Ag+ in solution having up to 25% (v/v nonaqueous fraction.

Organic nanostructures on silicon, created with semitransparent polystyrene spheres and 248 nm laser pulses

International Nuclear Information System (INIS)

Rothe, Erhard W; Manke, Charles W; Piparia, Reema; Baird, Ronald J

2008-01-01

Arrays of nanostructures are made starting with a template of close-packed, polystyrene spheres on a silicon surface. The spheres are either 1.091 or 2.99 μm in diameter (d) and are of polystyrene (PS). They are irradiated with a pulse of either 308 or 248 nm light to which they are transparent and semitransparent, respectively. A transparent sphere with d = 1.091 μm diameter concentrates incident light onto a small substrate area. As has been previously reported, that creates silicon nanobumps that rise from circular craters. At 248 nm and d = 2.99 μm, the light energy is mainly absorbed, destroys the sphere, and leaves a shrunken mass (typically about 500 nm wide and 100 nm high) of organic material that is probably polystyrene and its thermal degradation products. At 248 nm and d = 1.091 μm, the residual organic structures are on the order of 300 nm wide and 100 nm high. A distinctive feature is that these organic structures are connected by filaments that are on the order of 50 nm wide and 10 nm high. Filaments form because the close-packed PS spheres expand into each other during the early part of the laser pulse, and then, as the main structures shrink, their viscoelasticity leads to threads between them. Our results with 248 nm and d = 1.091 μm differ from those described by Huang et al with 248 nm and d = 1.0 μm. Future studies might include the further effect of wavelength and fluence upon the process as well the use of other materials and the replacement of nanospheres by other focusing shapes, such as ellipsoids or rods

Rear surface light emission measurements from laser-produced shock waves in clear and Al-coated polystyrene targets

Science.gov (United States)

McLean, E. A.; Deniz, A. V.; Schmitt, A. J.; Stamper, J. A.; Obenschain, S. P.; Lehecka, T.; Mostovych, A. N.; Seely, J.

1999-08-01

The Nike KrF laser, with its very uniform focal distributions, has been used at intensities near 10 14 W/cm 2 to launch shock waves in polystyrene targets. The rear surface visible light emission differed between clear polystyrene (CH) targets and targets with a thin (125 nm) Al coating on the rear side. The uncoated CH targets showed a relatively slowly rising emission followed by a sudden fall when the shock emerges, while the Al-coated targets showed a rapid rise in emission when the shock emerges followed by a slower fall, allowing an unambiguous determination of the time the shock arrived at the rear surface. A half-aluminized target allowed us to observe this difference in a single shot. The brightness temperature of both the aluminized targets and the non-aluminized targets was slightly below but close to rear surface temperature predictions of a hydrodynamic code. A discussion of preheat effects is given.

Application of 60Co γ-ray irradiated polystyrene microplate for anti-HCV ELISA

International Nuclear Information System (INIS)

Feng Bo; Zeng Hongyan; Tang Yufang; Wang Lu

2005-01-01

In order to explore the effect of 60 Co γ-ray irradiation on minor polypeptides absorption of polystyrene microplate, an indirect ELISA detection of anti-HCV was established, 60 Co γ-ray irradiated polystyrene microplates and the controls (without irradiation or UV-irradiated) were applied to absorb recombinant HCV antigens respectively. Cooperated with Bovine antihuman IgG labelled HRP, their related indices of sensitivity, specificity, homogeneity and stability were determinate. The results indicated that, optimum dose of the γ-ray irradiation is 8 kGy, and compared with the controls, detection sensitivity and homogeneity of the polystyrene microplate irradiated to 8 kGy could be improved markedly. (authors)

Fabrication of polystyrene/agave particle biocomposites using ...

Indian Academy of Sciences (India)

Polystyrene (PS) composites reinforced with ungrafted and acrylonitrile (AN) grafted agave particles (AgP) have been prepared with 10–30% particle content by weight using compression molding technique. The composite specimens thus prepared were subjected to the evaluation of mechanical, chemical, flammability and ...

High mass-asymmetry distributions of fissioning nuclei

International Nuclear Information System (INIS)

Sandulescu, A.; Lusting, H.J.; Hahn, J.; Greiner, W.

1978-07-01

It is shown that new mass-asymmetry valleys are appearing in the fragmentation potential V(l,eta) as function of the length l and mass-asymmetry coordinate eta = (A 1 - A 2 )to a correct treatment of the shell effects such that for separated fragments the shell effects equal the sum of the shell effects of the individual fragments and correspond to the double magic fragments 48 Ca, 78 Ni, 132 Sn and 208 Pb or may be 56 Ni. Also is shown that the fission mass-distributions have additional peaks corresponding to the bottom of these new valleys. The calculations are illustrated for 252 No and 238 U. The preliminary results show for 238 U relatively high percent yields in agreement with present available experimental data. (author)

Search for Z' --> e+ e- using dielectron mass and angular distribution.

Science.gov (United States)

Abulencia, A; Acosta, D; Adelman, J; Affolder, T; Akimoto, T; Albrow, M G; Ambrose, D; Amerio, S; Amidei, D; Anastassov, A; Anikeev, K; Annovi, A; Antos, J; Aoki, M; Apollinari, G; Arguin, J-F; Arisawa, T; Artikov, A; Ashmanskas, W; Attal, A; Azfar, F; Azzi-Bacchetta, P; Azzurri, P; Bacchetta, N; Bachacou, H; Badgett, W; Barbaro-Galtieri, A; Barnes, V E; Barnett, B A; Baroiant, S; Bartsch, V; Bauer, G; Bedeschi, F; Behari, S; Belforte, S; Bellettini, G; Bellinger, J; Belloni, A; Ben Haim, E; Benjamin, D; Beretvas, A; Beringer, J; Berry, T; Bhatti, A; Binkley, M; Bisello, D; Blair, R E; Blocker, C; Blumenfeld, B; Bocci, A; Bodek, A; Boisvert, V; Bolla, G; Bolshov, A; Bortoletto, D; Boudreau, J; Boveia, A; Brau, B; Bromberg, C; Brubaker, E; Budagov, J; Budd, H S; Budd, S; Burkett, K; Busetto, G; Bussey, P; Byrum, K L; Cabrera, S; Campanelli, M; Campbell, M; Canelli, F; Canepa, A; Carlsmith, D; Carosi, R; Carron, S; Casarsa, M; Castro, A; Catastini, P; Cauz, D; Cavalli-Sforza, M; Cerri, A; Cerrito, L; Chang, S H; Chapman, J; Chen, Y C; Chertok, M; Chiarelli, G; Chlachidze, G; Chlebana, F; Cho, I; Cho, K; Chokheli, D; Chou, J P; Chu, P H; Chuang, S H; Chung, K; Chung, W H; Chung, Y S; Ciljak, M; Ciobanu, C I; Ciocci, M A; Clark, A; Clark, D; Coca, M; Compostella, G; Convery, M E; Conway, J; Cooper, B; Copic, K; Cordelli, M; Cortiana, G; Cresciolo, F; Cruz, A; Cuenca Almenar, C; Cuevas, J; Culbertson, R; Cyr, D; DaRonco, S; D'Auria, S; D'Onofrio, M; Dagenhart, D; de Barbaro, P; De Cecco, S; Deisher, A; De Lentdecker, G; Dell'Orso, M; Delli Paoli, F; Demers, S; Demortier, L; Deng, J; Deninno, M; De Pedis, D; Derwent, P F; Dionisi, C; Dittmann, J R; DiTuro, P; Dörr, C; Donati, S; Donega, M; Dong, P; Donini, J; Dorigo, T; Dube, S; Ebina, K; Efron, J; Ehlers, J; Erbacher, R; Errede, D; Errede, S; Eusebi, R; Fang, H C; Farrington, S; Fedorko, I; Fedorko, W T; Feild, R G; Feindt, M; Fernandez, J P; Field, R; Flanagan, G; Flores-Castillo, L R; Foland, A; Forrester, S; Foster, G W; Franklin, M; Freeman, J C; Furic, I; Gallinaro, M; Galyardt, J; Garcia, J E; Garcia Sciveres, M; Garfinkel, A F; Gay, C; Gerberich, H; Gerdes, D; Giagu, S; Giannetti, P; Gibson, A; Gibson, K; Ginsburg, C; Giokaris, N; Giolo, K; Giordani, M; Giromini, P; Giunta, M; Giurgiu, G; Glagolev, V; Glenzinski, D; Gold, M; Goldschmidt, N; Goldstein, J; Gomez, G; Gomez-Ceballos, G; Goncharov, M; González, O; Gorelov, I; Goshaw, A T; Gotra, Y; Goulianos, K; Gresele, A; Griffiths, M; Grinstein, S; Grosso-Pilcher, C; Group, R C; Grundler, U; Guimaraes da Costa, J; Gunay-Unalan, Z; Haber, C; Hahn, S R; Hahn, K; Halkiadakis, E; Hamilton, A; Han, B-Y; Han, J Y; Handler, R; Happacher, F; Hara, K; Hare, M; Harper, S; Harr, R F; Harris, R M; Hatakeyama, K; Hauser, J; Hays, C; Heijboer, A; Heinemann, B; Heinrich, J; Herndon, M; Hidas, D; Hill, C S; Hirschbuehl, D; Hocker, A; Holloway, A; Hou, S; Houlden, M; Hsu, S-C; Huffman, B T; Hughes, R E; Huston, J; Incandela, J; Introzzi, G; Iori, M; Ishizawa, Y; Ivanov, A; Iyutin, B; James, E; Jang, D; Jayatilaka, B; Jeans, D; Jensen, H; Jeon, E J; Jindariani, S; Jones, M; Joo, K K; Jun, S Y; Junk, T R; Kamon, T; Kang, J; Karchin, P E; Kato, Y; Kemp, Y; Kephart, R; Kerzel, U; Khotilovich, V; Kilminster, B; Kim, D H; Kim, H S; Kim, J E; Kim, M J; Kim, S B; Kim, S H; Kim, Y K; Kirsch, L; Klimenko, S; Klute, M; Knuteson, B; Ko, B R; Kobayashi, H; Kondo, K; Kong, D J; Konigsberg, J; Korytov, A; Kotwal, A V; Kovalev, A; Kraan, A; Kraus, J; Kravchenko, I; Kreps, M; Kroll, J; Krumnack, N; Kruse, M; Krutelyov, V; Kuhlmann, S E; Kusakabe, Y; Kwang, S; Laasanen, A T; Lai, S; Lami, S; Lammel, S; Lancaster, M; Lander, R L; Lannon, K; Lath, A; Latino, G; Lazzizzera, I; LeCompte, T; Lee, J; Lee, J; Lee, Y J; Lee, S W; Lefèvre, R; Leonardo, N; Leone, S; Levy, S; Lewis, J D; Lin, C; Lin, C S; Lindgren, M; Lipeles, E; Liss, T M; Lister, A; Litvintsev, D O; Liu, T; Lockyer, N S; Loginov, A; Loreti, M; Loverre, P; Lu, R-S; Lucchesi, D; Lujan, P; Lukens, P; Lungu, G; Lyons, L; Lys, J; Lysak, R; Lytken, E; Mack, P; MacQueen, D; Madrak, R; Maeshima, K; Maki, T; Maksimovic, P; Malde, S; Manca, G; Margaroli, F; Marginean, R; Marino, C; Martin, A; Martin, V; Martínez, M; Maruyama, T; Matsunaga, H; Mattson, M E; Mazini, R; Mazzanti, P; McFarland, K S; McIntyre, P; McNulty, R; Mehta, A; Menzemer, S; Menzione, A; Merkel, P; Mesropian, C; Messina, A; von der Mey, M; Miao, T; Miladinovic, N; Miles, J; Miller, R; Miller, J S; Mills, C; Milnik, M; Miquel, R; Mitra, A; Mitselmakher, G; Miyamoto, A; Moggi, N; Mohr, B; Moore, R; Morello, M; Movilla Fernandez, P; Mülmenstädt, J; Mukherjee, A; Muller, Th; Mumford, R; Murat, P; Nachtman, J; Naganoma, J; Nahn, S; Nakano, I; Napier, A; Naumov, D; Necula, V; Neu, C; Neubauer, M S; Nielsen, J; Nigmanov, T; Nodulman, L; Norniella, O; Nurse, E; Ogawa, T; Oh, S H; Oh, Y D; Okusawa, T; Oldeman, R; Orava, R; Osterberg, K; Pagliarone, C; Palencia, E; Paoletti, R; Papadimitriou, V; Paramonov, A A; Parks, B; Pashapour, S; Patrick, J; Pauletta, G; Paulini, M; Paus, C; Pellett, D E; Penzo, A; Phillips, T J; Piacentino, G; Piedra, J; Pinera, L; Pitts, K; Plager, C; Pondrom, L; Portell, X; Poukhov, O; Pounder, N; Prakoshyn, F; Pronko, A; Proudfoot, J; Ptohos, F; Punzi, G; Pursley, J; Rademacker, J; Rahaman, A; Rakitin, A; Rappoccio, S; Ratnikov, F; Reisert, B; Rekovic, V; van Remortel, N; Renton, P; Rescigno, M; Richter, S; Rimondi, F; Ristori, L; Robertson, W J; Robson, A; Rodrigo, T; Rogers, E; Rolli, S; Roser, R; Rossi, M; Rossin, R; Rott, C; Ruiz, A; Russ, J; Rusu, V; Saarikko, H; Sabik, S; Safonov, A; Sakumoto, W K; Salamanna, G; Saltó, O; Saltzberg, D; Sanchez, C; Santi, L; Sarkar, S; Sartori, L; Sato, K; Savard, P; Savoy-Navarro, A; Scheidle, T; Schlabach, P; Schmidt, E E; Schmidt, M P; Schmitt, M; Schwarz, T; Scodellaro, L; Scott, A L; Scribano, A; Scuri, F; Sedov, A; Seidel, S; Seiya, Y; Semenov, A; Sexton-Kennedy, L; Sfiligoi, I; Shapiro, M D; Shears, T; Shepard, P F; Sherman, D; Shimojima, M; Shochet, M; Shon, Y; Shreyber, I; Sidoti, A; Sinervo, P; Sisakyan, A; Sjolin, J; Skiba, A; Slaughter, A J; Sliwa, K; Smith, J R; Snider, F D; Snihur, R; Soderberg, M; Soha, A; Somalwar, S; Sorin, V; Spalding, J; Spezziga, M; Spinella, F; Spreitzer, T; Squillacioti, P; Stanitzki, M; Staveris-Polykalas, A; St Denis, R; Stelzer, B; Stelzer-Chilton, O; Stentz, D; Strologas, J; Stuart, D; Suh, J S; Sukhanov, A; Sumorok, K; Sun, H; Suzuki, T; Taffard, A; Takashima, R; Takeuchi, Y; Takikawa, K; Tanaka, M; Tanaka, R; Tanimoto, N; Tecchio, M; Teng, P K; Terashi, K; Tether, S; Thom, J; Thompson, A S; Thomson, E; Tipton, P; Tiwari, V; Tkaczyk, S; Toback, D; Tokar, S; Tollefson, K; Tomura, T; Tonelli, D; Tönnesmann, M; Torre, S; Torretta, D; Tourneur, S; Trischuk, W; Tsuchiya, R; Tsuno, S; Turini, N; Ukegawa, F; Unverhau, T; Uozumi, S; Usynin, D; Vaiciulis, A; Vallecorsa, S; Varganov, A; Vataga, E; Velev, G; Veramendi, G; Veszpremi, V; Vidal, R; Vila, I; Vilar, R; Vine, T; Vollrath, I; Volobouev, I; Volpi, G; Würthwein, F; Wagner, P; Wagner, R G; Wagner, R L; Wagner, W; Wallny, R; Walter, T; Wan, Z; Wang, S M; Warburton, A; Waschke, S; Waters, D; Wester, W C; Whitehouse, B; Whiteson, D; Wicklund, A B; Wicklund, E; Williams, G; Williams, H H; Wilson, P; Winer, B L; Wittich, P; Wolbers, S; Wolfe, C; Wright, T; Wu, X; Wynne, S M; Yagil, A; Yamamoto, K; Yamaoka, J; Yamashita, T; Yang, C; Yang, U K; Yang, Y C; Yao, W M; Yeh, G P; Yoh, J; Yorita, K; Yoshida, T; Yu, G B; Yu, I; Yu, S S; Yun, J C; Zanello, L; Zanetti, A; Zaw, I; Zetti, F; Zhang, X; Zhou, J; Zucchelli, S

2006-06-02

We search for Z' bosons in dielectron events produced in pp collisions at square root of s = 1.96 TeV, using 0.45 fb(-1) of data accumulated with the Collider Detector at Fermilab II detector at the Fermilab Tevatron. To identify the Z' --> e+ e- signal, both the dielectron invariant mass distribution and the angular distribution of the electron pair are used. No evidence of a signal is found, and 95% confidence level lower limits are set on the Z' mass for several models. Limits are also placed on the mass and gauge coupling of a generic Z', as well as on the contact-interaction mass scales for different helicity structure scenarios.

Fission fragment mass distributions via prompt γ-ray spectroscopy

Indian Academy of Sciences (India)

The distribution of fragment masses formed in nuclear fission is one of the most strik- ing features .... 80. 100. 120. 140. 160. 10. 3. 10. 4. Fragment Mass. Relative yield. Sn. Cd. Te. Pd ... the secondary fragment at Z = 50 and N = 82 shells, where the yields are depleted. Both ... More systematic experimental data are required.

Generalised extreme value distributions provide a natural hypothesis for the shape of seed mass distributions.

Directory of Open Access Journals (Sweden)

Will Edwards

Full Text Available Among co-occurring species, values for functionally important plant traits span orders of magnitude, are uni-modal, and generally positively skewed. Such data are usually log-transformed "for normality" but no convincing mechanistic explanation for a log-normal expectation exists. Here we propose a hypothesis for the distribution of seed masses based on generalised extreme value distributions (GEVs, a class of probability distributions used in climatology to characterise the impact of event magnitudes and frequencies; events that impose strong directional selection on biological traits. In tests involving datasets from 34 locations across the globe, GEVs described log10 seed mass distributions as well or better than conventional normalising statistics in 79% of cases, and revealed a systematic tendency for an overabundance of small seed sizes associated with low latitudes. GEVs characterise disturbance events experienced in a location to which individual species' life histories could respond, providing a natural, biological explanation for trait expression that is lacking from all previous hypotheses attempting to describe trait distributions in multispecies assemblages. We suggest that GEVs could provide a mechanistic explanation for plant trait distributions and potentially link biology and climatology under a single paradigm.

Biodegradation of weathered polystyrene films in seawater microcosms.

Science.gov (United States)

Syranidou, Evdokia; Karkanorachaki, Katerina; Amorotti, Filippo; Franchini, Martina; Repouskou, Eftychia; Kaliva, Maria; Vamvakaki, Maria; Kolvenbach, Boris; Fava, Fabio; Corvini, Philippe F-X; Kalogerakis, Nicolas

2017-12-21

A microcosm experiment was conducted at two phases in order to investigate the ability of indigenous consortia alone or bioaugmented to degrade weathered polystyrene (PS) films under simulated marine conditions. Viable populations were developed on PS surfaces in a time dependent way towards convergent biofilm communities, enriched with hydrocarbon and xenobiotics degradation genes. Members of Alphaproteobacteria and Gammaproteobacteria were highly enriched in the acclimated plastic associated assemblages while the abundance of plastic associated genera was significantly increased in the acclimated indigenous communities. Both tailored consortia efficiently reduced the weight of PS films. Concerning the molecular weight distribution, a decrease in the number-average molecular weight of films subjected to microbial treatment was observed. Moreover, alteration in the intensity of functional groups was noticed with Fourier transform infrared spectrophotometry (FTIR) along with signs of bio-erosion on the PS surface. The results suggest that acclimated marine populations are capable of degrading weathered PS pieces.

Syntheses, spectroscopic and magnetic properties of polystyrene-anchored coordination compounds of thiazolidinone

Directory of Open Access Journals (Sweden)

D. Kumar

2014-01-01

Full Text Available The reaction between polystyrene 3-formylsalicylate and furoic acid hydrazide in DMF in the presence of ethyl acetate results in the formation of polystyrene N-(2-carbamoylfuranyl-3'-carboxy-2'-hydroxybenzylideneimine (I. A benzene suspension of I reacts with mercaptoacetic acid and forms the polystyrene N-(2-carbamoylfuranyl-C-(3'-carboxy-2'-hydroxyphenylthiazolidin-4-one, PSCH2–LH2 (II. A DMF suspension of II reacts with Mn(II, Ni(II, Cd(II, Fe(III and UO2(VI ions and forms the polystyrene-anchored coordination compounds of the types, [PSCH2–LMn(DMF3], [PSCH2–LNi(DMF3], [PSCH2–LCd(DMF], [PSCH2–LH2FeCl3] and [PSCH2–LHUO2(NO3(DMF]. The polystyrene-anchored coordination compounds have been characterized on the basis of elemental analyses, spectral (IR, reflectance studies and magnetic susceptibility measurements. II acts as a neutral tridentate ONO donor ligand in [PSCH2–LH2FeCl3], a monobasic tridentate ONO donor ligand in [PSCH2–LHUO2(NO3(DMF], a dibasic tridentate ONO donor ligand in [PSCH2–LMn(DMF3], [PSCH2–LNi(DMF3] and [PSCH2–LCd(DMF]. A tetrahedral structure for Cd(II and an octahedral structure for Mn(II, Ni(II, Fe(III and a square-antiprism geometry for UO2(VI complex are suggested. DOI: http://dx.doi.org/10.4314/bcse.v28i1.4

Polystyrene tube radioimmunoabsorbent assay for IgE anti-penicillin antibody

International Nuclear Information System (INIS)

Urena, V.; Delgado, R.G.; Daroca, P.; Lahoz, C.

1977-01-01

A radioimmunoassay technique has been developed based on the binding capacity of polystyrene for proteins. The method was tested on sera from thirteen patients with suspected penicillin allergy, five healthy controls, and three patients with seasonal pollen reactions. The results were compared with those obtained by the radio-allergoabsorbent method (RAST) and with basophil degranulation by penicillin. A penicillin/ovalbumin conjugate (pen-OA) was prepared and polystyrene tubes were incubated with pen-OA, 3% human serum albumin to block free sites, 1/10 dilution of test serum, anti-IgE antiserum specific for epsilon chains, and 125 I-IgE. The tubes were washed after the incubation period and the empty tubes counted in a γ scintillation counter. The specificity of the method was tested by an inhibition assay. The technique seemed more sensitive than the RAST method, the results were reproducible and in general showed good correlation with those of the RAST method. This polystyrene tube radioimmunoabsorbent method therefore provides a simple, specific and sensitive diagnostic technique for penicillin allergy. (U.K)

Polystyrene star-shaped polymers made by the new In-Inmethod

International Nuclear Information System (INIS)

Fazeli, N.; Afshar Toromi, F.

2002-01-01

Three main methods are usually used for the synthesis of star-shaped polymers, where each one has its own advantages and disadvantages. Among these techniques, i n-out m ethod is the best one to produce hetero arm star polymers with narrow molecular weight distribution and long arms with active sites at the end of the second-generation arms. This method, however, has some difficulties during the synthesis of hetero-arm star polymers with styrene or dienes as the second monomers. The reason is that in the o ut s tep, the carbanions of the growing chain attack the existing double bonds of the other cores and produce an irreversible gel. The new i n-in m ethod mentioned in this paper, is used to synthesize double-star polystyrene polymers with relatively narrow molecular weight distribution and without occurrence of any gelation during the process. With the monomers, which are able to attack the existing double bonds of the cores of the star polymers, it is also possible to produce-hetero-arm star polymers using this new method

The supernova progenitor mass distributions of M31 and M33: further evidence for an upper mass limit

Energy Technology Data Exchange (ETDEWEB)

Jennings, Zachary G.; Weisz, Daniel R. [University of California Observatories, Santa Cruz, CA 95064 (United States); Williams, Benjamin F.; Dalcanton, Julianne J.; Gilbert, Karoline M.; Fouesneau, Morgan [Box 351580, The University of Washington Seattle, WA 98195 (United States); Murphy, Jeremiah W. [Department of Physics, Florida State University, Tallahassee, FL 32306 (United States); Dolphin, Andrew E., E-mail: zgjennin@ucsc.edu, E-mail: adolphin@raytheon.com [Raytheon, 1151 E. Hermans Road, Tucson, AZ 85706 (United States)

2014-11-10

Using Hubble Space Telescope photometry to measure star formation histories, we age-date the stellar populations surrounding supernova remnants (SNRs) in M31 and M33. We then apply stellar evolution models to the ages to infer the corresponding masses for their supernova progenitor stars. We analyze 33 M33 SNR progenitors and 29 M31 SNR progenitors in this work. We then combine these measurements with 53 previously published M31 SNR progenitor measurements to bring our total number of progenitor mass estimates to 115. To quantify the mass distributions, we fit power laws of the form dN/dM∝M {sup –α}. Our new larger sample of M31 progenitors follows a distribution with α=4.4{sub −0.4}{sup +0.4}, and the M33 sample follows a distribution with α=3.8{sub −0.5}{sup +0.4}. Thus both samples are consistent within the uncertainties, and the full sample across both galaxies gives α=4.2{sub −0.3}{sup +0.3}. Both the individual and full distributions display a paucity of massive stars when compared to a Salpeter initial mass function, which we would expect to observe if all massive stars exploded as SN that leave behind observable SNR. If we instead fix α = 2.35 and treat the maximum mass as a free parameter, we find M {sub max} ∼ 35-45 M {sub ☉}, indicative of a potential maximum cutoff mass for SN production. Our results suggest that either SNR surveys are biased against finding objects in the youngest (<10 Myr old) regions, or the highest mass stars do not produce SNe.

Determination of several trace metals in biological materials by PIXE analysis after solvent extraction and polystyrene-film collection

International Nuclear Information System (INIS)

Iwata, Yoshihiro; Korenaga, Tatsumi; Suzuki, Nobuo

1991-01-01

Traces of vanadium, manganese, iron, cobalt, nickel, copper, and zinc were quantitatively extracted with diethyldithiocarbamate (DDTC) in benzene from a digested solution of biological materials and the metal-DDTC complexes were collected into a small amount of polystyrene foam produced by lyophilization of the benzene extract after addition of polystyrene. The polystyrene foam was dissolved in benzene and spread on Mylar film. After drying, a polystyrene film containing metal-DDTC complexes was produced on Mylar film, and then the polystyrene film was peeled from the Mylar film. This film was subjected to PIXE analysis. This method was applied to NBS SRM 1572 citrus leaves and a marine macroalgal sample, and 6 trace metals were simultaneously and accurately determined. (author)

Effects of fissioning nuclei distributions on fragment mass distributions for high energy fission

Directory of Open Access Journals (Sweden)

Rossi P C R

2012-02-01

Full Text Available We study the effects of fissioning nuclei mass- and energy-distributions on the formation of fragments for fission induced by high energy probes. A Monte Carlo code called CRISP was used for obtaining mass distributions and spectra of the fissioning nuclei for reactions induced by 660 MeV protons on 241Am and on 239Np, by 500 MeV protons on 208Pb, and by Bremsstrahlung photons with end-point energies at 50 MeV and 3500 MeV on 238U. The results show that even at high excitation energies, asymmetric fission may still contribute significantly to the fission cross section of actinide nuclei, while it is the dominante mode in the case of lead. However, more precise data for high energy fission on actinide are necessary in order to allow definite conclusions.

AFM-based force spectroscopy on polystyrene brushes: effect of brush thickness on protein adsorption.

Science.gov (United States)

Hentschel, Carsten; Wagner, Hendrik; Smiatek, Jens; Heuer, Andreas; Fuchs, Harald; Zhang, Xi; Studer, Armido; Chi, Lifeng

2013-02-12

Herein we present a study on nonspecific binding of proteins at highly dense packed hydrophobic polystyrene brushes. In this context, an atomic force microscopy tip was functionalized with concanavalin A to perform single-molecule force spectroscopy measurements on polystyrene brushes with thicknesses of 10 and 60 nm, respectively. Polystyrene brushes with thickness of 10 nm show an almost two times stronger protein adsorption than brushes with a thickness of 60 nm: 72 pN for the thinner and 38 pN for the thicker layer, which is in qualitative agreement with protein adsorption studies conducted macroscopically by fluorescence microscopy.

Tritium-doping enhancement of polystyrene by ultraviolet laser and hydrogen plasma irradiation for laser fusion experiments

Energy Technology Data Exchange (ETDEWEB)

Iwasa, Yuki, E-mail: iwasa-y@ile.osaka-u.ac.jp [Institute of Laser Engineering, Osaka University, 2-6 Yamadaoka, Suita, Osaka 565-0871 (Japan); Yamanoi, Kohei; Iwano, Keisuke; Empizo, Melvin John F.; Arikawa, Yasunobu; Fujioka, Shinsuke; Sarukura, Nobuhiko; Shiraga, Hiroyuki; Takagi, Masaru; Norimatsu, Takayoshi; Azechi, Hiroshi [Institute of Laser Engineering, Osaka University, 2-6 Yamadaoka, Suita, Osaka 565-0871 (Japan); Noborio, Kazuyuki; Hara, Masanori; Matsuyama, Masao [Hydrogen Isotope Research Center, Organization for Promotion of Research, University of Toyama, 3190 Gofuku, Toyama 930-8555 (Japan)

2016-11-15

Highlights: • Tritium-doped polystyrene films are fabricated by the Wilzbach method with UV laser and hydrogen plasma irradiation. • The 266-nm laser-irradiated, 355-nm laser-irradiated, and hydrogen plasma-irradiated polystyrene films exhibit higher PSL intensities and specific radioactivities than the non-irradiated sample. • Tritium doping by UV laser irradiation can be largely affected by the laser wavelength because of polystyrene’s absorption. • Hydrogen plasma irradiation results to a more uniform doping concentration even at low partial pressure and short irradiation time. • UV laser and plasma irradiations can be utilized to fabricate tritium-doped polystyrene shell targets for future laser fusion experiments. - Abstract: We investigate the tritium-doping enhancement of polystyrene by ultraviolet (UV) laser and hydrogen plasma irradiation. Tritium-doped polystyrene films are fabricated by the Wilzbach method with UV laser and hydrogen plasma. The 266-nm laser-irradiated, 355-nm laser-irradiated, and hydrogen plasma-irradiated polystyrene films exhibit higher PSL intensities and specific radioactivities than the non-irradiated sample. Tritium doping by UV laser irradiation can be largely affected by the laser wavelength because of polystyrene’s absorption. In addition, UV laser irradiation is more localized and concentrated at the spot of laser irradiation, while hydrogen plasma irradiation results to a more uniform doping concentration even at low partial pressure and short irradiation time. Both UV laser and plasma irradiations can nevertheless be utilized to fabricate tritium-doped polystyrene targets for future laser fusion experiments. With a high doping rate and efficiency, a 1% tritium-doped polystyrene shell target having 7.6 × 10{sup 11} Bq g{sup −1} specific radioactivity can be obtained at a short period of time thereby decreasing tritium consumption and safety management costs.

Optical Properies of Polystyrene Films Doped by Methyl Green Dye

Directory of Open Access Journals (Sweden)

Asrar A. Saeed

2017-11-01

Full Text Available Effects of methyl green (MG dye on the optical properties of polystyrene (PS have been studied. Pure polystyrene and MG doped PS films were prepared by using casting method. These films were characterized using UV/VIS spectrophotometer technique in order to estimate the type of electric transition which was found to be indirect transition. The value of the optical energy gap was decreased with increasing doping ratios of methyl green dye. Absorption coefficient, extinction coefficient, refractive index and energy gap have been also investigated; it was found that all the above parameters affects by doping dye.

HYDRATION AND MICROSTRUCTURE OF BLENDED CEMENT WITH SODIUM POLYSTYRENE SULFONATE

Directory of Open Access Journals (Sweden)

Weifeng Li

2017-03-01

Full Text Available Polystyrene foamed plastic wastes are a kind of environmental pollutant. It could be recycled in cement industry as a chemical agent. In this paper, the effects of sodium polystyrene sulfonate (SPS on the hydration and microstructure of blended cement were investigated by calorimetry, X-ray diffraction (XRD, scanning electron microscopy (SEM and mercury intrusion porosimetry (MIP. SPS slightly delayed the hydration of alite and decreased its hydration degree. SPS did not change the phase compositions during hydration. SPS changed the morphology of ettringite (AFt and decreased the pore volumes and the sizes of pores.

Synthesis of magnetic hollow silica using polystyrene bead as a template

International Nuclear Information System (INIS)

Wu, W.; Caruntu, D.; Martin, A.; Yu, M.H.; O'Connor, C.J.; Zhou, W.L.; Chen, J.-F.

2007-01-01

In this paper, we report a new route to synthesize novel magnetic hollow silica nanospheres (MHSNs) using polystyrene particles as sacrificial templates, and TEOS and Fe 3 O 4 as precursors. TEM, EDS, XRD, and SQUID were applied to characterize MHSNs. TEM and EDS results show that the MHSNs consist of about 200 nm of hollow cores and ∼35 nm shells with ∼10 nm of Fe 3 O 4 nanoparticles embedded. The polystyrene beads were successfully removed by immersing the as-prepared silica nanocomposite in a toluene solution. XRD results demonstrate that the Fe 3 O 4 magnetic nanoparticles still keep spinel structure even heated at low temperature. The surface status of the polystyrene beads and Fe 3 O 4 nanoparticles has an important effect on the formation of the MHSNs. The MHSNs present a superparamagnetism at room temperature by SQUID measurement. The MHSNs have potential applications in biosystem and nanomedicine

Impact of water chemistry on surface charge and aggregation of polystyrene microspheres suspensions.

Science.gov (United States)

Lu, Songhua; Zhu, Kairuo; Song, Wencheng; Song, Gang; Chen, Diyun; Hayat, Tasawar; Alharbi, Njud S; Chen, Changlun; Sun, Yubing

2018-07-15

The discharge of microplastics into aquatic environment poses the potential threat to the hydrocoles and human health. The fate and transport of microplastics in aqueous solutions are significantly influenced by water chemistry. In this study, the effect of water chemistry (i.e., pH, foreign salts and humic acid) on the surface charge and aggregation of polystyrene microsphere in aqueous solutions was conducted by batch, zeta potentials, hydrodynamic diameters, FT-IR and XPS analysis. Compared to Na + and K + , the lower negative zeta potentials and larger hydrodynamic diameters of polystyrene microspheres after introduction of Mg 2+ were observed within a wide range of pH (2.0-11.0) and ionic strength (IS, 0.01-500mmol/L). No effect of Cl - , HCO 3 - and SO 4 2- on the zeta potentials and hydrodynamic diameters of polystyrene microspheres was observed at low IS concentrations (10mmol/L). The zeta potentials of polystyrene microspheres after HA addition were decreased at pH2.0-11.0, whereas the lower hydrodynamic diameters were observed at pH<4.0. According to FT-IR and XPS analysis, the change in surface properties of polystyrene microspheres after addition of hydrated Mg 2+ and HA was attributed to surface electrostatic and/or steric repulsions. These investigations are crucial for understanding the effect of water chemistry on colloidal stability of microplastics in aquatic environment. Copyright © 2018 Elsevier B.V. All rights reserved.

A novel anion exchange membrane from polystyrene (ethylene butylene) polystyrene: Synthesis and characterization

Energy Technology Data Exchange (ETDEWEB)

Vinodh, Rajangam; Ilakkiya, Arjunan; Elamathi, Swaminathan [Department of Chemistry, Anna University Chennai, Sardar Patel Road, Chennai 600025, Tamil Nadu (India); Sangeetha, Dharmalingam, E-mail: sangeetha@annauniv.ed [Department of Chemistry, Anna University Chennai, Sardar Patel Road, Chennai 600025, Tamil Nadu (India)

2010-02-25

We look forward for an eco-friendly hydrocarbon polymer with higher molecular weight for the preparation of an anion exchange membrane. Polystyrene ethylene butylene polystyrene (PSEBS) was chosen as the polymer matrix. The anion exchange membrane was prepared from PSEBS tri-block co-polymer and then the properties were characterized for alkaline fuel cell application. The preparation of anion exchange polymer involved two steps namely chloromethylation and quaternization. The anion exchange membrane with high conductivity has been prepared by introducing quaternary ammonium groups in to the polymer. Finally, the membrane was prepared using solution casting method. The solution casting method yields highly hydrophilic membranes with uniform structure that were suitable for electrochemical applications. The efficiency of the entrapment was monitored by swelling ratio, chemical stability and ion exchange measurement. The characteristic structural properties of the membrane were investigated by FT-IR spectroscopy and {sup 1}H NMR spectroscopy. The thermal stability of the membrane was characterized by TGA, DSC and DMA (dynamic mechanical analysis). The prepared uniform electrolyte membrane in this study has high thermal and chemical stability. The surface morphology and elemental composition of the quaternized PSEBS was determined by SEM-EDXA techniques, respectively. The measured hydroxyl ion conductivity of the synthesized alkaline PSEBS polymer electrolyte membrane showed ionic conductivity in the range of 10{sup -3} S/cm in deionized water at room temperature. It was found that the substitution provided a flexible, chemically and thermally stable membrane. Hence, the membrane will have potential application in the alkaline fuel cell.

A novel anion exchange membrane from polystyrene (ethylene butylene) polystyrene: Synthesis and characterization

International Nuclear Information System (INIS)

Vinodh, Rajangam; Ilakkiya, Arjunan; Elamathi, Swaminathan; Sangeetha, Dharmalingam

2010-01-01

We look forward for an eco-friendly hydrocarbon polymer with higher molecular weight for the preparation of an anion exchange membrane. Polystyrene ethylene butylene polystyrene (PSEBS) was chosen as the polymer matrix. The anion exchange membrane was prepared from PSEBS tri-block co-polymer and then the properties were characterized for alkaline fuel cell application. The preparation of anion exchange polymer involved two steps namely chloromethylation and quaternization. The anion exchange membrane with high conductivity has been prepared by introducing quaternary ammonium groups in to the polymer. Finally, the membrane was prepared using solution casting method. The solution casting method yields highly hydrophilic membranes with uniform structure that were suitable for electrochemical applications. The efficiency of the entrapment was monitored by swelling ratio, chemical stability and ion exchange measurement. The characteristic structural properties of the membrane were investigated by FT-IR spectroscopy and 1 H NMR spectroscopy. The thermal stability of the membrane was characterized by TGA, DSC and DMA (dynamic mechanical analysis). The prepared uniform electrolyte membrane in this study has high thermal and chemical stability. The surface morphology and elemental composition of the quaternized PSEBS was determined by SEM-EDXA techniques, respectively. The measured hydroxyl ion conductivity of the synthesized alkaline PSEBS polymer electrolyte membrane showed ionic conductivity in the range of 10 -3 S/cm in deionized water at room temperature. It was found that the substitution provided a flexible, chemically and thermally stable membrane. Hence, the membrane will have potential application in the alkaline fuel cell.

Learning Curves of Virtual Mastoidectomy in Distributed and Massed Practice.

Science.gov (United States)

Andersen, Steven Arild Wuyts; Konge, Lars; Cayé-Thomasen, Per; Sørensen, Mads Sølvsten

2015-10-01

Repeated and deliberate practice is crucial in surgical skills training, and virtual reality (VR) simulation can provide self-directed training of basic surgical skills to meet the individual needs of the trainee. Assessment of the learning curves of surgical procedures is pivotal in understanding skills acquisition and best-practice implementation and organization of training. To explore the learning curves of VR simulation training of mastoidectomy and the effects of different practice sequences with the aim of proposing the optimal organization of training. A prospective trial with a 2 × 2 design was conducted at an academic teaching hospital. Participants included 43 novice medical students. Of these, 21 students completed time-distributed practice from October 14 to November 29, 2013, and a separate group of 19 students completed massed practice on May 16, 17, or 18, 2014. Data analysis was performed from June 6, 2014, to March 3, 2015. Participants performed 12 repeated virtual mastoidectomies using a temporal bone surgical simulator in either a distributed (practice blocks spaced in time) or massed (all practice in 1 day) training program with randomization for simulator-integrated tutoring during the first 5 sessions. Performance was assessed using a modified Welling Scale for final product analysis by 2 blinded senior otologists. Compared with the 19 students in the massed practice group, the 21 students in the distributed practice group were older (mean age, 25.1 years), more often male (15 [62%]), and had slightly higher mean gaming frequency (2.3 on a 1-5 Likert scale). Learning curves were established and distributed practice was found to be superior to massed practice, reported as mean end score (95% CI) of 15.7 (14.4-17.0) in distributed practice vs. 13.0 (11.9-14.1) with massed practice (P = .002). Simulator-integrated tutoring accelerated the initial performance, with mean score for tutored sessions of 14.6 (13.9-15.2) vs. 13.4 (12.8-14.0) for

The surface pressure dynamics and appearance of mixed monolayers of cholesterol and different sized polystyrenes at an air-water interface.

Science.gov (United States)

Mudgil, Poonam; Dennis, Gary R; Millar, Thomas J

2005-02-15

Synthetic polymers are increasingly being used in situations where they are designed to interact with biological systems. As a result, it is important to investigate the interactions of the polymers with biochemicals. We have used cholesterol, as an example of an important biological surfactant component, to study its interactions with polystyrene. Mixed monolayers of cholesterol and one of two different molecular weight polystyrenes were formed at an air-water interface to investigate their interactions and to determine whether the size of the polystyrene affected the interaction. The pressure-area (pi-A) isocycles of mixed monolayers of cholesterol and polystyrene MW 2700 or polystyrene MW32700 showed that strongest attractive interactions occur at high surface pressures and in polystyrene rich films. The excess area and excess free energy of mixing were most negative at high surface pressures and at high mole fraction of polystyrene. The most stable mixed monolayers were formed with X(PS2700) = 0.9 and X(PS32700) = 0.09. Microscopic observation of the mixed monolayers of cholesterol and polystyrene showed the formation of stable islands in the cholesterol/polystyrene mixtures. These observations, the nature of the inflection points in the isocycles, and the anomalous changes in free energy lead us to conclude that there is a stable rearrangement of polystyrene into compact islands when it is mixed with cholesterol. Any excess cholesterol is excluded from these islands and remains as a separate film surrounding the islands.

Fission profits of thorium: Distribution in charge and mass

International Nuclear Information System (INIS)

Guarnieri, A.A.

1985-01-01

It is presented the improvement of a semi-empiric model to describe behavior fo the 235 U + thermal neutrons system. The model is applied to fission of the 232 Th case reproducing the distribution of mass profits of fission products from the behavior of independent profits of fragments related the mass and charge, and the emission of prompt neutrons per fragment. (M.C.K.) [pt

Implications of the Cosmological Constant for Spherically Symmetric Mass Distributions

Science.gov (United States)

Zubairi, Omair; Weber, Fridolin

2013-04-01

In recent years, scientists have made the discovery that the expansion rate of the Universe is increasing rather than decreasing. This acceleration leads to an additional term in Albert Einstein's field equations which describe general relativity and is known as the cosmological constant. This work explores the aftermath of a non-vanishing cosmological constant for relativistic spherically symmetric mass distributions, which are susceptible to change against Einstein's field equations. We introduce a stellar structure equation known as the Tolman-Oppenhiemer-Volkoff (TOV) equation modified for a cosmological constant, which is derived from Einstein's modified field equations. We solve this modified TOV equation for these spherically symmetric mass distributions and obtain stellar properties such as mass and radius and investigate changes that may occur depending on the value of the cosmological constant.

Small angle X-ray scattering study on the conformation of polystyrene in the anti-solvent process of supercritical fluids

International Nuclear Information System (INIS)

Liu Yi; Wang Hongli; Zhao Xin; Chen Na; Li Dan; Liu Zhimin; Han Buxing; Rong Lixia; Zhao Hui; Wang Jun; Dong Baozhong

2003-01-01

The conformation of polystyrene in the anti-solvent process of supercritical fluids (compressed CO 2 + polystyrene + tetrahydrofuran) is studied by synchrotron radiation X-ray small angle scattering (SAXS). Coil-to-globule transform of polystyrene chain is observed with increasing the concentration of CO 2 . It is found that polystyrene coils at the pressure lower than cloud point pressure (p c ) and changes into globule with uniform density at the pressure higher than p c

Fragment mass distribution of proton-induced spallation reaction with intermediate energy

International Nuclear Information System (INIS)

Fan Sheng; Ye Yanlin; Xu Chuncheng; Chen Tao; Sobolevsky, N.M.

2000-01-01

The test of part benchmark of SHIELD code is finished. The fragment cross section and mass distribution and excitation function of the residual nuclei from proton-induced spallation reaction on thin Pb target with intermediate energy have been calculated by SHIELD code. And the results are in good agreement with measured data. The fragment mass distribution of the residual nuclei from proton-induced spallation reaction on thick Pb target with incident energy 1.6 GeV have been simulated

On widths of mass distributions in statistical theory of fission

International Nuclear Information System (INIS)

Volkov, N.G.; Emel'yanov, V.M.

1979-01-01

The process of nucleon tunneling from one fragment to another near the point of the compoUnd-nucleus fragmentation has been studied in the model of a two-center oscillator. The effect of the number of transferred nucleons on the mass distribution of fragments is estimated. Sensitivity of the model to the form of the single-particle potential, excitation eneraies and deformation of fragments is examined. The calculations performed show that it is possible to calculate the mass distributions at the point of fragment contact in the statistical fission model, taking account of the nucleon exchange between fragments

Altered behavior, physiology, and metabolism in fish exposed to polystyrene nanoparticles

DEFF Research Database (Denmark)

Mattsson, Karin; Ekvall, Mikael T; Hansson, Lars-Anders

2015-01-01

that enter natural ecosystems, such as oceans and lakes, is increasing, and degradation of the disposed plastics produces smaller particles toward the nano scale. Therefore, it is of utmost importance to gain knowledge about how plastic nanoparticles enter and affect living organisms. Here we have...... administered 24 and 27 nm polystyrene nanoparticles to fish through an aquatic food chain, from algae through Daphnia, and studied the effects on behavior and metabolism. We found severe effects on feeding and shoaling behavior as well as metabolism of the fish; hence, we conclude that polystyrene...

Calculating the mass distribution of heavy nucleus fission product by neutrons

International Nuclear Information System (INIS)

Gudkov, A.N.; Koldobskij, A.B.; Kolobashkin, V.M.; Semenova, E.V.

1981-01-01

The technique of calculating the fission product mass yields by neutrons which are necessary for performing nucleus physical calculations in designing nuclear reactor cores is considered. The technique is based on the approximation of fission product mass distribution over the whole mass range by five Gauss functions. New analytical expressions for determining energy weights of used gaussians are proposed. The results of comparison of experimental data with calculated values for fission product mass obtained for reference processes in the capacity of which the fission reactions are chosen: 233 U, 235 U fission by thermal neutrons, 232 Th, 233 U, 235 U, 238 U by fission spectrum neutrons and 14 MeV neutrons and for 232 Th fission reactions by 11 MeV neutrons and 238 U by 7.7 MeV neutrons. On the basis of the analysis of results obtained the conclusion is drawn on a good agreement of fission product mass yield calculation values obtained using recommended values of mass distribution parameters with experimental data [ru

Tuning the wettability of calcite cubes by varying the sizes of the polystyrene nanoparticles attached to their surfaces

International Nuclear Information System (INIS)

He Yongjun; Li Tanliang; Yu Xiangyang; Zhao Shiyong; Lu Jianhua; He Jia

2007-01-01

The wettability of calcite cubes was tuned by varying the sizes of the polystyrene nanoparticles attached to their surfaces via a dispersion polymerization. The products were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersion spectrum (EDS) and Fourier transformation infrared spectrum (FTIR). The results showed that the hydrophobicity of the calcite cubes was enhanced with the increase of the size of the polystyrene nanoparticles attached. Using polystyrene nanoparticle-attached calcite cubes (PNACC) as emulsifiers, stable water-in-tricaprylin Pickering emulsions were produced. By gelling the water droplets of the Pickering emulsions, the hierarchical structures of polystyrene nanoparticle-attached calcite cube-armored microspheres were obtained. The polystyrene nanoparticle-attached calcite cubes were expected to have novel surface properties similar neither to traditional Pickering particles, nor to macroscopically asymmetrical Janus particles

Mass and angular distributions of the reaction products in heavy ion collisions

Science.gov (United States)

Nasirov, A. K.; Giardina, G.; Mandaglio, G.; Kayumov, B. M.; Tashkhodjaev, R. B.

2018-05-01

The optimal reactions and beam energies leading to synthesize superheavy elements is searched by studying mass and angular distributions of fission-like products in heavy-ion collisions since the evaporation residue cross section consists an ignorable small part of the fusion cross section. The intensity of the yield of fission-like products allows us to estimate the probability of the complete fusion of the interacting nuclei. The overlap of the mass and angular distributions of the fusion-fission and quasifission products causes difficulty at estimation of the correct value of the probability of the compound nucleus formation. A study of the mass and angular distributions of the reaction products is suitable key to understand the interaction mechanism of heavy ion collisions.

Cathodic electrogenerated chemiluminescence of aromatic Tb(III) chelates at polystyrene-graphite composite electrodes

International Nuclear Information System (INIS)

Salminen, Kalle; Grönroos, Päivi; Tuomi, Sami; Kulmala, Sakari

2017-01-01

Tb(III) chelates exhibit intense hot electron-induced electrogenerated chemiluminescence during cathodic polarization of metal/polystyrene-graphite (M/PG) electrodes in fully aqueous solutions. The M/PG working electrode provides a sensitive means for the determination of aromatic Tb(III) chelates at nanomolar concentration levels with a linear log-log calibration curve spanning more than five orders of magnitude. The charge transport and other properties of these novel electrodes were studied by electrochemiluminescence measurements and cyclic voltammetry. The present composite electrodes can by utilized both under pulse polarization and DC polarization unlike oxide-coated metal electrodes which do not tolerate cathodic DC polarization. The present cost-effective electrodes could be utilized e.g. in immunoassays where polystyrene is extensively used as a solid phase for various bioaffinity assays by using electrochemiluminescent Tb(III) chelates or e.g. Ru(bpy) 3 2+ as labels. - Highlights: • Generation of hydrated electrons at Polystyrene-graphite electrodes. • The insulating polystyrene layer on the outer electrode surface seems necessary. • Hydrated electrons are able to produce chemiluminescence. • Strongest signal and lowest std. dev. achieved at same graphite weight fraction.

Nano-porous Material with Spherical or Gyroid Cavities Created by Quantitative Etching of Polydimethylsiloxane in Polystyrene-Polydimethylsiloxane Block Copolymers

DEFF Research Database (Denmark)

Ndoni, Sokol; Vigild, Martin Etchells; Berg, Rolf H.

2003-01-01

A new method for quantitative etching of the poly(dimethylsiloxane) block in polystyrene-poly(dimethylsiloxane) (PS-PDMS) block copolymers is reported. Reacting the block copolymer with anhydrous hydrogen fluoride renders a nanoporous material (NPM) with the remaining glassy PS maintaining...... the original bulk morphology. 1H NMR, mass difference, size exclusion chromatography, and X-ray photoelectron spectroscopy were used to characterize the materials before and after etching. NPMs containing spherical and gyroid cavities were prepared, as ascertained by small-angle X-ray scattering...

Influence of polystyrene addition to cellulose on chemical structure and properties of bio-oil obtained during pyrolysis

International Nuclear Information System (INIS)

Rutkowski, Piotr; Kubacki, Andrzej

2006-01-01

The cellulose (C), polystyrene (PS) and cellulose/polystyrene (C-PS) mixtures (3:1, 1:1, 1:3 w/w) were subjected to a pyrolysis process to produce bio-oil. The pyrolytic oil yield was in the range of 45.5-94.8 wt% depending on the composition of the sample. Pyrolysis of polystyrene gives the highest oil yield, whereas for cellulose, the yield of liquid products was the lowest. The basic physicochemical properties of oils are strongly influenced by the original material and do not change additively. The polystyrene addition to cellulose clearly improves the quality of the bio-oil, resulting in decreases in acid number, pour point and density. The change of color is not so distinct. The FT-IR analysis of the oils showed that the oxygen functionalities and hydrocarbons contents highly depend on the composition of the cellulose/polystyrene mixture. The fractionation of bio-oils by column chromatography using hexane and benzene was followed by GC-MS analyses. Different classes of organic compounds were identified, i.e., carboxylic acids, phenols, aldehydes, ketones, esters, ethers and unsaturated linear and cyclic hydrocarbons. The proportion of hydrocarbons increases with a decrease of the cellulose/polystyrene ratio. The obtained results indicate that during pyrolysis, not only does decomposition of cellulose and polystyrene occur, but also, reactions between products from C and PS take place. That was proved by the presence of compounds identified only in the bio-oils obtained from C-PS compositions

Leachate From Expanded Polystyrene Cups Is Toxic to Aquatic Invertebrates (Ceriodaphnia dubia

Directory of Open Access Journals (Sweden)

Clara Thaysen

2018-02-01

Full Text Available Expanded polystyrene (EPS products and their associated chemicals (e.g., styrenes are widespread in the marine environment. As a consequence, bans on their use for single-use packaging materials are being proposed in several municipalities. To better understand how science can inform decision-making, we looked at the available scientific literature about contamination and effects and conducted experiments to measure chemical leachate from polystyrene products and toxicity from the leachate. We conducted leaching experiments with common food matrices (water, soup broth, gravy, black coffee and coffee with cream and sugar at relevant temperatures (70 and 95°C that are consumed in or with several polystyrene products (coffee cup lids, polystyrene stir sticks, polystyrene spoons, EPS cups, EPS bowls, and EPS takeout containers. We analyzed each sample for styrene, ethylbenzene, toluene, benzene, meta- and para- xylene, isopropylbenzene, and isopropyltoluene—chemicals associated with polystyrene products. To determine whether the leachates are toxic, we conducted chronic toxicity tests, measuring survival and reproductive output in Ceriodaphnia dubia. Toxicity tests included nine treatments: seven concentrations of ethylbenzene, EPS cup leachate and a negative control. Overall, we found that temperature has a significant effect on leaching. We only detected leachates in trials conducted at higher temperature −95°C. Ethylbenzene was the only target analyte with final concentrations above the method limit of detection, and was present in the greatest concentrations in EPS and with soup broth. Measurable concentrations of ethylbenzene in the leachate ranged from 1.3 to 3.4 μg/L. In toxicity tests, the calculated LC50 for ethylbenzene was 14 mg/L and the calculated LC20 was 210 μg/L. For the treatment exposed to the EPS cup leachate, mortality was 40%—four times greater than the negative control. Finally, there was no significant difference (p

The Mass-Ratio Distribution of Visual Binary Stars

NARCIS (Netherlands)

Hogeveen, S.J.

1990-01-01

The selection effects that govern the observations of Visual Binary Stars are in- vestigated, in order to obtain a realistic statistical distribution of the mass-ratio q = Msec=Mprim. To this end a numerical simulation programme has been developed, which `generates' binary stars and `looks' at

Conversion of Hazardous Motor Vehicle Used Tire and Polystyrene Waste Plastic Mixture into useful Chemical Products

OpenAIRE

Moinuddin Sarker; Mohammad Mamunor Rashid

2014-01-01

Motor vehicle used tire and polystyrene waste plastic mixture into fuel recovery using thermal degradation process in laboratory batch process. Motor vehicle used tire and polystyrene waste plastic was use 75 gm by weight. Motor vehicle tire was 25 gm and polystyrene waste plastic was 50 gm. In presence of oxygen experiment was performed under laboratory fume hood. Thermal degradation temperature range was 100 - 420 oC and experiment run time was 5 hours. Product fuel density is 0.84 gm/ml an...

Core-powered mass-loss and the radius distribution of small exoplanets

Science.gov (United States)

Ginzburg, Sivan; Schlichting, Hilke E.; Sari, Re'em

2018-05-01

Recent observations identify a valley in the radius distribution of small exoplanets, with planets in the range 1.5-2.0 R⊕ significantly less common than somewhat smaller or larger planets. This valley may suggest a bimodal population of rocky planets that are either engulfed by massive gas envelopes that significantly enlarge their radius, or do not have detectable atmospheres at all. One explanation of such a bimodal distribution is atmospheric erosion by high-energy stellar photons. We investigate an alternative mechanism: the luminosity of the cooling rocky core, which can completely erode light envelopes while preserving heavy ones, produces a deficit of intermediate sized planets. We evolve planetary populations that are derived from observations using a simple analytical prescription, accounting self-consistently for envelope accretion, cooling and mass-loss, and demonstrate that core-powered mass-loss naturally reproduces the observed radius distribution, regardless of the high-energy incident flux. Observations of planets around different stellar types may distinguish between photoevaporation, which is powered by the high-energy tail of the stellar radiation, and core-powered mass-loss, which depends on the bolometric flux through the planet's equilibrium temperature that sets both its cooling and mass-loss rates.

A multivariate rank test for comparing mass size distributions

KAUST Repository

Lombard, F.

2012-04-01

Particle size analyses of a raw material are commonplace in the mineral processing industry. Knowledge of particle size distributions is crucial in planning milling operations to enable an optimum degree of liberation of valuable mineral phases, to minimize plant losses due to an excess of oversize or undersize material or to attain a size distribution that fits a contractual specification. The problem addressed in the present paper is how to test the equality of two or more underlying size distributions. A distinguishing feature of these size distributions is that they are not based on counts of individual particles. Rather, they are mass size distributions giving the fractions of the total mass of a sampled material lying in each of a number of size intervals. As such, the data are compositional in nature, using the terminology of Aitchison [1] that is, multivariate vectors the components of which add to 100%. In the literature, various versions of Hotelling\\'s T 2 have been used to compare matched pairs of such compositional data. In this paper, we propose a robust test procedure based on ranks as a competitor to Hotelling\\'s T 2. In contrast to the latter statistic, the power of the rank test is not unduly affected by the presence of outliers or of zeros among the data. © 2012 Copyright Taylor and Francis Group, LLC.

Integration of polystyrene microlenses with both convex and concave profiles in a polymer-based microfluidic system

KAUST Repository

Fan, Yiqiang; Li, Huawei; Foulds, Ian G.

2013-01-01

This paper reports a new technique of fabricating polystyrene microlenses with both convex and concave profiles that are integrated in polymer-based microfluidic system. The polystyrene microlenses, or microlens array, are fabricated using the free

Fabrication of Cationic Exchange Polystyrene Nanofibers for Drug ...

African Journals Online (AJOL)

Purpose: To prepare polystyrene nanofiber ion exchangers (PSNIE) with surface cation exchange functionality using a new method based on electrospinning and also to optimize crosslinking and sulfonation reactions to obtain PSNIE with maximum ion exchange capacity (IEC). Method: The nanofibers were prepared from ...

Syntheses, magnetic and spectral studies on polystyrene supported ...

Indian Academy of Sciences (India)

Unknown

DMF results in the formation of polystyrene-anchored monobasic bidentate Schiff base, ... studied ligands in coordination chemistry. On ac- count of their pronounced coordinating properties, a ... Experimental ... temperature and then was suction-filtered, washed .... vent due to its high dielectric constant and its ability.

Steady shear rheology of dilute polystyrene particle gels

NARCIS (Netherlands)

Folkersma, R.; Diemen, van A.J.G.; Laven, J.; Stein, H.N.

1999-01-01

This paper describes an experimental study on dispersions of monodisperse polystyrene (PS) spheres with a typical radius of 1 µm, dispersed in an electrolyte at high ionic strength, screening the electrostatic repulsion. These suspensions gelate at rest even at low volume fractions of PS particles.

Search for new physics in dijet mass and angular distributions

Indian Academy of Sciences (India)

We present a search for physics beyond the Standard Model in proton–proton collisions at a centre-of-mass energy of s = 7 TeV, performed with the ATLAS detector at the Large Hadron Collider (LHC). No evidence for new physics is found in dijet mass and angular distributions and stringent limits are set on a variety of ...

Mass and charge distribution in heavy-ion collisions

International Nuclear Information System (INIS)

Beck, F.; Dworzecka, M.; Feldmeier, H.

1978-01-01

A statistical model based on the independent particle picture is used to calculate mass and charge distributions in deep inelastic heavy-ion collisions. Different assumptions on volume and charge equilibrations are compared with measured variances of charge distributions. One combination of assumptions is clearly favoured by experiment, and gives a reasonable description of the variance versus energy loss curves up to energy losses of about 200 MeV in the heavy systems Kr+Ho and Xe+Bi, and up to about 60 MeV for the light system Ar+Ca [af

Mass Distribution in Galaxy Cluster Cores

Energy Technology Data Exchange (ETDEWEB)

Hogan, M. T.; McNamara, B. R.; Pulido, F.; Vantyghem, A. N. [Department of Physics and Astronomy, University of Waterloo, Waterloo, ON, N2L 3G1 (Canada); Nulsen, P. E. J. [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street, Cambridge, MA 02138 (United States); Russell, H. R. [Institute of Astronomy, Madingley Road, Cambridge CB3 0HA (United Kingdom); Edge, A. C. [Centre for Extragalactic Astronomy, Department of Physics, Durham University, Durham DH1 3LE (United Kingdom); Main, R. A., E-mail: m4hogan@uwaterloo.ca [Canadian Institute for Theoretical Astrophysics, University of Toronto, 60 St. George Street, Toronto, ON, M5S 3H8 (Canada)

2017-03-01

Many processes within galaxy clusters, such as those believed to govern the onset of thermally unstable cooling and active galactic nucleus feedback, are dependent upon local dynamical timescales. However, accurate mapping of the mass distribution within individual clusters is challenging, particularly toward cluster centers where the total mass budget has substantial radially dependent contributions from the stellar ( M {sub *}), gas ( M {sub gas}), and dark matter ( M {sub DM}) components. In this paper we use a small sample of galaxy clusters with deep Chandra observations and good ancillary tracers of their gravitating mass at both large and small radii to develop a method for determining mass profiles that span a wide radial range and extend down into the central galaxy. We also consider potential observational pitfalls in understanding cooling in hot cluster atmospheres, and find tentative evidence for a relationship between the radial extent of cooling X-ray gas and nebular H α emission in cool-core clusters. At large radii the entropy profiles of our clusters agree with the baseline power law of K ∝ r {sup 1.1} expected from gravity alone. At smaller radii our entropy profiles become shallower but continue with a power law of the form K ∝ r {sup 0.67} down to our resolution limit. Among this small sample of cool-core clusters we therefore find no support for the existence of a central flat “entropy floor.”.

Scaling analysis of meteorite shower mass distributions

DEFF Research Database (Denmark)

Oddershede, Lene; Meibom, A.; Bohr, Jakob

1998-01-01

Meteorite showers are the remains of extraterrestrial objects which are captivated by the gravitational field of the Earth. We have analyzed the mass distribution of fragments from 16 meteorite showers for scaling. The distributions exhibit distinct scaling behavior over several orders of magnetude......; the observed scaling exponents vary from shower to shower. Half of the analyzed showers show a single scaling region while the orther half show multiple scaling regimes. Such an analysis can provide knowledge about the fragmentation process and about the original meteoroid. We also suggest to compare...... the observed scaling exponents to exponents observed in laboratory experiments and discuss the possibility that one can derive insight into the original shapes of the meteoroids....

Measuring thermal conductivity of polystyrene nanowires using the dual-cantilever technique.

Science.gov (United States)

Canetta, Carlo; Guo, Samuel; Narayanaswamy, Arvind

2014-10-01

Thermal conductance measurements are performed on individual polystyrene nanowires using a novel measurement technique in which the wires are suspended between two bi-material microcantilever sensors. The nanowires are fabricated via electrospinning process. Thermal conductivity of the nanowire samples is found to be between 6.6 and 14.4 W m(-1) K(-1) depending on sample, a significant increase above typical bulk conductivity values for polystyrene. The high strain rates characteristic of electrospinning are believed to lead to alignment of molecular polymer chains, and hence the increase in thermal conductivity, along the axis of the nanowire.

Production and testing of {sup 244}Cm-labeled fluorescent polystyrene latex microspheres

Energy Technology Data Exchange (ETDEWEB)

Guilmette, R A; Mueller, H L; Brodbeck, R D

1988-12-01

To provide a useful tool for studying the mechanisms of retention and translocation of respirable-sized, alpha-emitting particles, we have developed a method of incorporating {sup 244}Cm into fluorescent polystyrene latex microspheres. The resultant particles contain alpha radioactivity comparable to {mu}m-size (AMAD) {sup 239}Pu0{sub 2} particles, but are easily visible by fluorescent light microscopy. Preliminary testing of the particles with dog macrophages in vitro has shown that the initial uptake of these Cm-labeled particles is more rapid than uptake of unlabeled particles of similar size. We are continuing to develop procedures for achieving better particle yields, smaller dispersity of particle size distributions and improved retention of the Cm label by the particles. (author)

Preparation and thermal properties of polystyrene/silica nanocomposites

Czech Academy of Sciences Publication Activity Database

Bera, O.; Pilić, B.; Pavličević, J.; Jovičić, M.; Holló, B.; Meszaros Szecsenyi, K.; Špírková, Milena

2011-01-01

Roč. 515, č. 1/2 (2011), s. 1-5 ISSN 0040-6031 R&D Projects: GA AV ČR(CZ) IAAX08240901 Institutional research plan: CEZ:AV0Z40500505 Keywords : polystyrene * silica nanoparticles * nanocomposites Subject RIV: JI - Composite Materials Impact factor: 1.805, year: 2011

Fission fragment mass and total kinetic energy distributions of spontaneously fissioning plutonium isotopes

Science.gov (United States)

Pomorski, K.; Nerlo-Pomorska, B.; Bartel, J.; Schmitt, C.

2018-03-01

The fission-fragment mass and total kinetic energy (TKE) distributions are evaluated in a quantum mechanical framework using elongation, mass asymmetry, neck degree of freedom as the relevant collective parameters in the Fourier shape parametrization recently developed by us. The potential energy surfaces (PES) are calculated within the macroscopic-microscopic model based on the Lublin-Strasbourg Drop (LSD), the Yukawa-folded (YF) single-particle potential and a monopole pairing force. The PES are presented and analysed in detail for even-even Plutonium isotopes with A = 236-246. They reveal deep asymmetric valleys. The fission-fragment mass and TKE distributions are obtained from the ground state of a collective Hamiltonian computed within the Born-Oppenheimer approximation, in the WKB approach by introducing a neck-dependent fission probability. The calculated mass and total kinetic energy distributions are found in good agreement with the data.

Elongational viscosity of monodisperse and bidisperse polystyrene melts

DEFF Research Database (Denmark)

Nielsen, Jens Kromann; Rasmussen, Henrik Koblitz; Hassager, Ole

2005-01-01

The startup and steady uniaxial elongational viscosity have been measured for two monodisperse polystyrene melts with molecular weights of 52 kg/mole (PS52K) and 103 kg/mole (PS103K), and for three bidisperse polystyrene melts. The bidisperse melts consist of PS103K or PS52K and a monodisperse...... (closed loop proportional regulator) using the laser in such a way that the stretch rate at the neck is kept constant. The rheometer has been described in more detail in (A. Bach, H.K. Rasmussen and O. Hassager, Journal of Rheology, 47 (2003) 429). PS390K show a decrease in the steady viscosity as a power......-law function of the elongational rate (A. Bach, K. Almdal, H.K. Rasmussen and O. Hassager, Macromolecules 36 (2003) 5174). PS52K and PS103K show that the steady viscosity has a maximum that is respectively 100% and 50% above 3 times the zero-shear-rate viscosity. The bidisperse melts show a significant...

Surface-enhanced Raman spectroscopy substrate based on Ag-coated self-assembled polystyrene spheres

Science.gov (United States)

Mikac, Lara; Ivanda, Mile; Gotić, Marijan; Janicki, Vesna; Zorc, Hrvoje; Janči, Tibor; Vidaček, Sanja

2017-10-01

The silver (Ag) films were deposited on the monodispersed polystyrene spheres that were drop-coated on hydrophilic glass substrates in order to form a self-assembled 2D monolayer. Thus prepared Ag films over polystyrene nanospheres (AgFONs) were used to record the surface-enhanced Raman scattering (SERS) spectra of rhodamine 6G (R6G) and pyridine (λex = 514.5 nm). AgFONs were prepared by depositing 120, 180 and 240 nm thick Ag layer on the 1000 nm polystyrene spheres and 80, 120, 160 and 200 nm thick Ag layer on the 350 nm spheres as well as on their mixture (350 + 1000 nm). The silver was deposited by electron beam evaporation technique. The best enhancement of the Raman signal for both test molecules was obtained using 180 nm Ag film deposited on the 1000 nm spheres and using 80 nm Ag film deposited on the 350 nm polystyrene spheres. The lowest detectable concentrations of R6G and pyridine were 10-9 mol L-1 and 1.2 × 10-3 mol L-1, respectively. This study has shown that AgFONs could be regarded as good and reproducible SERS substrate for analytical detection of various organic molecules.

Physical and Chemical Changes of Polystyrene Nanospheres Irradiated with Laser

International Nuclear Information System (INIS)

Mustafa, Mohd Ubaidillah; Juremi, Nor Rashidah Md.; Mohamad, Farizan; Wibawa, Pratama Jujur; Agam, Mohd Arif; Ali, Ahmad Hadi

2011-01-01

It has been reported that polymer resist such as PMMA (Poly(methyl methacrylate) which is a well known and commonly used polymer resist for fabrication of electronic devices can show zwitter characteristic due to over exposure to electron beam radiation. Overexposed PMMA tend to changes their molecular structure to either become negative or positive resist corresponded to electron beam irradiation doses. These characteristic was due to crosslinking and scissors of the PMMA molecular structures, but till now the understanding of crosslinking and scissors of the polymer resist molecular structure due to electron beam exposure were still unknown to researchers. Previously we have over exposed polystyrene nanospheres to various radiation sources, such as electron beam, solar radiation and laser, which is another compound that can act as polymer resist. We investigated the physical and chemical structures of the irradiated polystyrene nanospheres with FTIR analysis. It is found that the physical and chemical changes of the irradiated polystyrene were found to be corresponded with the radiation dosages. Later, combining Laser irradiation and Reactive Ion Etching manipulation, created a facile technique that we called as LARIEA NSL (Laser and Reactive Ion Etching Assisted Nanosphere Lithography) which can be a facile technique to fabricate controllable carbonaceous nanoparticles for applications such as lithographic mask, catalysts and heavy metal absorbers.

Radiation effect on polystyrene deposited and grafted on silica gel

International Nuclear Information System (INIS)

Kusama, Y.; Udagawa, A.; Takehisa, M.

1978-01-01

The effect of radiation on polystyrene was studied in the presence and absence of silica gel by molecular weight measurement with gel permeation chromatography (GPC). Polystyrene crosslinked under vacuum in the absence of silica gel, but it either crosslinked or degraded by radiation, depending on the molecular weight of the polymer in the presence of silica gel. part of the deposited polymer bonded to silica gel by radiation; the G value for graft-chain formation is in the range of 0.01 to 0.1. Irradiation of polystyrene grafted on silica gel resulted in degradation of the graft chain because of the transfer of energy from silica gel. The G value for main chain scission was about 2 when graft polymer was irradiated in the absence of homopolymer. The degradation of graft polymer was suppressed when the polymer was irradiated in the presence of homopolymer, and the amount of unextractable polymer from silica gel increased with increasing irradiation. This adds evidence to the estimation that an increase in grafting percent coupled with a slight decrease in molecular weight at a later stage of radiation-induced polymerization of styrene adsorbed on slica gel is due to a secondary effect of radiation on the polymer

Characteristic relation for the mass and energy distribution of the nuclear fission products

International Nuclear Information System (INIS)

Alexandru, G.

1977-01-01

The dispersion relation for nuclear fission is written in the two part fragmentation approach which allows to obtain the characteristic relation for the mass and energy distribution of the nuclear fission products. One explains the resonance approximation in the mass distribution of the fission products taking into account the high order resonances too. (author)

Determination of the mass-ratio distribution, I: single-lined spectroscopic binary stars

NARCIS (Netherlands)

Hogeveen, S.J.

1992-01-01

For single-lined spectroscopic binary stars (sbi), the mass ratio q = Msec=Mprim is calculated from the mass function f(m), which is determined from observations. For statistical investigations of the mass-ratio distribution, the term sin^3 i, that remains in the cubic equation from which q is

Few-layer graphene growth from polystyrene as solid carbon source utilizing simple APCVD method

Science.gov (United States)

Ahmadi, Shahrokh; Afzalzadeh, Reza

2016-07-01

This research article presents development of an economical, simple, immune and environment friendly process to grow few-layer graphene by controlling evaporation rate of polystyrene on copper foil as catalyst and substrate utilizing atmospheric pressure chemical vapor deposition (APCVD) method. Evaporation rate of polystyrene depends on molecular structure, amount of used material and temperature. We have found controlling rate of evaporation of polystyrene by controlling the source temperature is easier than controlling the material weight. Atomic force microscopy (AFM) as well as Raman Spectroscopy has been used for characterization of the layers. The frequency of G‧ to G band ratio intensity in some samples varied between 0.8 and 1.6 corresponding to few-layer graphene. Topography characterization by atomic force microscopy confirmed Raman results.

Radiation damage studies on polystyrene-based scintillators

International Nuclear Information System (INIS)

Britvich, G.I.; Peresypkin, A.I.; Rykalin, V.I.

1991-01-01

The radiation resistance of polystyrene-based scintillators containing various scintillation dopes is reported. All samples were irradiated to 137 Cs gamma rays in air at room temperature. The examination of radiation resistance of about thirty fluorescence compounds has been made. The most radiation-hard fluores are X25, X31, 3HF and M3HF. 1 fig.; 6 tabs

Spectroscopic and antimicrobial studies of polystyrene films under ...

Indian Academy of Sciences (India)

Spectroscopic and antimicrobial studies of polystyrene films under air plasma and He-Ne laser treatment ... The parameters such as (1) surface area by contact angle measurements, (2) quality of material before and after treatment by SEM and FTIR spectra and (3) material characterization by UV-vis spectra were studied.

Functional electrospun polystyrene nanofibers incorporating α-, β-, and γ-cyclodextrins: comparison of molecular filter performance.

Science.gov (United States)

Uyar, Tamer; Havelund, Rasmus; Hacaloglu, Jale; Besenbacher, Flemming; Kingshott, Peter

2010-09-28

Electrospinning has been used to successfully create polystyrene (PS) nanofibers containing either of three different types of cyclodextrin (CD); α-CD, β-CD, and γ-CD. These three CDs are chosen because they have different sized cavities that potentially allow for selective inclusion complex (IC) formation with molecules of different size or differences in affinity of IC formation with one type of molecule. The CD containing electrospun PS nanofibers (PS/CD) were initially characterized by scanning electron microscopy (SEM) to determine the uniformity of the fibers and their fiber diameter distributions. X-ray photoelectron spectroscopy (XPS) was used to quantitatively determine the concentration of each CD on the different fiber surfaces. Static time-of-flight secondary ion mass spectrometry (static-ToF-SIMS) showed the presence of each type of CD on the PS nanofibers by the detection of both the CD sodium adduct molecular ions (M + Na+) and lower molecular weight oxygen containing fragment ions. The comparative efficiency of the PS/CD nanofibers/nanoweb for removing phenolphthalein, a model organic compound, from solution was determined by UV-vis spectrometry, and the kinetics of phenolphthalein capture was shown to follow the trend PS/α-CD > PS/β-CD > PS/γ-CD. Direct pyrolysis mass spectrometry (DP-MS) was also performed to ascertain the relative binding strengths of the phenolphthalein for the CD cavities, and the results showed the trend in the interaction strength was β-CD > γ-CD > α-CD. Our results demonstrate that nanofibers produced by electrospinning that incorporate cyclodextrins with different sized cavities can indeed filter organic molecules and can potentially be used for filtration, purification, and/or separation processes.

Thermo-mechanical properties of polystyrene-based shape memory nanocomposites

NARCIS (Netherlands)

Xu, B.; Fu, Y.Q.; Ahmad, M.; Luo, J.K.; Huang, W.M.; Kraft, A.; Reuben, R.; Pei, Y.T.; Chen, Zhenguo; Hosson, J.Th.M. De

2010-01-01

Shape memory nanocomposites were fabricated using chemically cross-linked polystyrene (PS) copolymer as a matrix and different nanofillers (including alumina, silica and clay) as the reinforcing agents. Their thermo-mechanical properties and shape memory effects were characterized. Experimental

Polystyrene negative resist for high-resolution electron beam lithography

Directory of Open Access Journals (Sweden)

Ma Siqi

2011-01-01

Full Text Available Abstract We studied the exposure behavior of low molecular weight polystyrene as a negative tone electron beam lithography (EBL resist, with the goal of finding the ultimate achievable resolution. It demonstrated fairly well-defined patterning of a 20-nm period line array and a 15-nm period dot array, which are the densest patterns ever achieved using organic EBL resists. Such dense patterns can be achieved both at 20 and 5 keV beam energies using different developers. In addition to its ultra-high resolution capability, polystyrene is a simple and low-cost resist with easy process control and practically unlimited shelf life. It is also considerably more resistant to dry etching than PMMA. With a low sensitivity, it would find applications where negative resist is desired and throughput is not a major concern.

Hydrophobic Polystyrene Passivation Layer for Simultaneously Improved Efficiency and Stability in Perovskite Solar Cells.

Science.gov (United States)

Li, Minghua; Yan, Xiaoqin; Kang, Zhuo; Huan, Yahuan; Li, Yong; Zhang, Ruxiao; Zhang, Yue

2018-06-06

The major restraint for the commercialization of the high-performance hybrid metal halide perovskite solar cells is the long-term stability, especially at the infirm interface between the perovskite film and organic charge-transfer layer. Recently, engineering the interface between the perovskite and spiro-OMeTAD becomes an effective strategy to simultaneously improve the efficiency and stability in the perovskite solar cells. In this work, we demonstrated that introducing an interfacial polystyrene layer between the perovskite film and spiro-OMeTAD layer can effectively improve the perovskite solar cells photovoltaic performance. The inserted polystyrene layer can passivate the interface traps and defects effectively and decrease the nonradiative recombination, leading to enhanced photoluminescence intensity and carrier lifetime, without compromising the carrier extraction and transfer. Under the optimized condition, the perovskite solar cells with the polystyrene layer achieve an enhanced average power efficiency of about 19.61% (20.46% of the best efficiency) from about 17.63% with negligible current density-voltage hysteresis. Moreover, the optimized perovskite solar cells with the hydrophobic polystyrene layer can maintain about 85% initial efficiency after 2 months storage in open air conditions without encapsulation.

Mass distribution for the two-photon channel

CERN Multimedia

ATLAS, collaboration

2012-01-01

Mass distribution for the two-photon channel. The strongest evidence for this new particle comes from analysis of events containing two photons. The smooth dotted line traces the measured background from known processes. The solid line traces a statistical fit to the signal plus background. The new particle appears as the excess around 126.5 GeV. The full analysis concludes that the probability of such a peak is three chances in a million.

Mass distribution for the four-lepton channel.

CERN Multimedia

ATLAS, collaboration

2012-01-01

Mass distribution for the four-lepton channel. The search with the purest expected signal is done by examining events with two Z bosons that have decayed to pairs of electrons or muons. In the region from 120 to 130 GeV, 13 events are seen where only 5.3 were expected. The complete analysis concludes that the probability of such an excess would be three times in ten thousand if there were no new particle.

Optimization of orthotropic distributed-mode loudspeaker using attached masses and multi-exciters.

Science.gov (United States)

Lu, Guochao; Shen, Yong; Liu, Ziyun

2012-02-01

Based on the orthotropic model of the plate, the method to optimize the sound response of the distributed-mode loudspeaker (DML) using the attached masses and the multi-exciters has been investigated. The attached masses method will rebuild the modes distribution of the plate, based on which multi-exciter method will smooth the sound response. The results indicate that the method can be used to optimize the sound response of the DML. © 2012 Acoustical Society of America

Phenotyping polyclonal kappa and lambda light chain molecular mass distributions in patient serum using mass spectrometry.

Science.gov (United States)

Barnidge, David R; Dasari, Surendra; Ramirez-Alvarado, Marina; Fontan, Adrian; Willrich, Maria A V; Tschumper, Renee C; Jelinek, Diane F; Snyder, Melissa R; Dispenzieri, Angela; Katzmann, Jerry A; Murray, David L

2014-11-07

We previously described a microLC-ESI-Q-TOF MS method for identifying monoclonal immunoglobulins in serum and then tracking them over time using their accurate molecular mass. Here we demonstrate how the same methodology can be used to identify and characterize polyclonal immunoglobulins in serum. We establish that two molecular mass distributions observed by microLC-ESI-Q-TOF MS are from polyclonal kappa and lambda light chains using a combination of theoretical molecular masses from gene sequence data and the analysis of commercially available purified polyclonal IgG kappa and IgG lambda from normal human serum. A linear regression comparison of kappa/lambda ratios for 74 serum samples (25 hypergammaglobulinemia, 24 hypogammaglobulinemia, 25 normal) determined by microflowLC-ESI-Q-TOF MS and immunonephelometry had a slope of 1.37 and a correlation coefficient of 0.639. In addition to providing kappa/lambda ratios, the same microLC-ESI-Q-TOF MS analysis can determine the molecular mass for oligoclonal light chains observed above the polyclonal background in patient samples. In 2 patients with immune disorders and hypergammaglobulinemia, we observed a skewed polyclonal molecular mass distribution which translated into biased kappa/lambda ratios. Mass spectrometry provides a rapid and simple way to combine the polyclonal kappa/lambda light chain abundance ratios with the identification of dominant monoclonal as well as oligoclonal light chain immunoglobulins. We anticipate that this approach to evaluating immunoglobulin light chains will lead to improved understanding of immune deficiencies, autoimmune diseases, and antibody responses.

Uniaxial Elongational viscosity of bidisperse polystyrene melts

DEFF Research Database (Denmark)

Nielsen, Jens Kromann; Rasmussen, Henrik K.; Hassager, Ole

2006-01-01

The startup and steady uniaxial elongational viscosity have been measured for three bidisperse polystyrene (PS) melts, consisting of blends of monodisperse PS with molecular weights of 52 kg/mole or 103 kg/mole and 390 kg/mole. The bidisperse melts have a maximum in the steady elongational...... viscosity, of up to a factor of 7 times the Trouton limit of 3 times the zero-shear viscosity....

Melt dispersion of thermoplastic polystyrene in polymer polyols

NARCIS (Netherlands)

2009-01-01

Polystyrene is dispersed into a polyol via a mechanical dispersion process. A stabilizer is present to stabilize the dispersed polymer particles. The stabilizer includes a copolymer of (1) from 10 to 70% by weight of a branched polyol which has a molecular weight of from 4000 to 20,000, from 0.2 to

Large-Scale Ichthyoplankton and Water Mass Distribution along the South Brazil Shelf

Science.gov (United States)

de Macedo-Soares, Luis Carlos Pinto; Garcia, Carlos Alberto Eiras; Freire, Andrea Santarosa; Muelbert, José Henrique

2014-01-01

Ichthyoplankton is an essential component of pelagic ecosystems, and environmental factors play an important role in determining its distribution. We have investigated simultaneous latitudinal and cross-shelf gradients in ichthyoplankton abundance to test the hypothesis that the large-scale distribution of fish larvae in the South Brazil Shelf is associated with water mass composition. Vertical plankton tows were collected between 21°27′ and 34°51′S at 107 stations, in austral late spring and early summer seasons. Samples were taken with a conical-cylindrical plankton net from the depth of chlorophyll maxima to the surface in deep stations, or from 10 m from the bottom to the surface in shallow waters. Salinity and temperature were obtained with a CTD/rosette system, which provided seawater for chlorophyll-a and nutrient concentrations. The influence of water mass on larval fish species was studied using Indicator Species Analysis, whereas environmental effects on the distribution of larval fish species were analyzed by Distance-based Redundancy Analysis. Larval fish species were associated with specific water masses: in the north, Sardinella brasiliensis was found in Shelf Water; whereas in the south, Engraulis anchoita inhabited the Plata Plume Water. At the slope, Tropical Water was characterized by the bristlemouth Cyclothone acclinidens. The concurrent analysis showed the importance of both cross-shelf and latitudinal gradients on the large-scale distribution of larval fish species. Our findings reveal that ichthyoplankton composition and large-scale spatial distribution are determined by water mass composition in both latitudinal and cross-shelf gradients. PMID:24614798

Large-scale ichthyoplankton and water mass distribution along the South Brazil Shelf.

Directory of Open Access Journals (Sweden)

Luis Carlos Pinto de Macedo-Soares

Full Text Available Ichthyoplankton is an essential component of pelagic ecosystems, and environmental factors play an important role in determining its distribution. We have investigated simultaneous latitudinal and cross-shelf gradients in ichthyoplankton abundance to test the hypothesis that the large-scale distribution of fish larvae in the South Brazil Shelf is associated with water mass composition. Vertical plankton tows were collected between 21°27' and 34°51'S at 107 stations, in austral late spring and early summer seasons. Samples were taken with a conical-cylindrical plankton net from the depth of chlorophyll maxima to the surface in deep stations, or from 10 m from the bottom to the surface in shallow waters. Salinity and temperature were obtained with a CTD/rosette system, which provided seawater for chlorophyll-a and nutrient concentrations. The influence of water mass on larval fish species was studied using Indicator Species Analysis, whereas environmental effects on the distribution of larval fish species were analyzed by Distance-based Redundancy Analysis. Larval fish species were associated with specific water masses: in the north, Sardinella brasiliensis was found in Shelf Water; whereas in the south, Engraulis anchoita inhabited the Plata Plume Water. At the slope, Tropical Water was characterized by the bristlemouth Cyclothone acclinidens. The concurrent analysis showed the importance of both cross-shelf and latitudinal gradients on the large-scale distribution of larval fish species. Our findings reveal that ichthyoplankton composition and large-scale spatial distribution are determined by water mass composition in both latitudinal and cross-shelf gradients.

Large-scale ichthyoplankton and water mass distribution along the South Brazil Shelf.

Science.gov (United States)

de Macedo-Soares, Luis Carlos Pinto; Garcia, Carlos Alberto Eiras; Freire, Andrea Santarosa; Muelbert, José Henrique

2014-01-01

Ichthyoplankton is an essential component of pelagic ecosystems, and environmental factors play an important role in determining its distribution. We have investigated simultaneous latitudinal and cross-shelf gradients in ichthyoplankton abundance to test the hypothesis that the large-scale distribution of fish larvae in the South Brazil Shelf is associated with water mass composition. Vertical plankton tows were collected between 21°27' and 34°51'S at 107 stations, in austral late spring and early summer seasons. Samples were taken with a conical-cylindrical plankton net from the depth of chlorophyll maxima to the surface in deep stations, or from 10 m from the bottom to the surface in shallow waters. Salinity and temperature were obtained with a CTD/rosette system, which provided seawater for chlorophyll-a and nutrient concentrations. The influence of water mass on larval fish species was studied using Indicator Species Analysis, whereas environmental effects on the distribution of larval fish species were analyzed by Distance-based Redundancy Analysis. Larval fish species were associated with specific water masses: in the north, Sardinella brasiliensis was found in Shelf Water; whereas in the south, Engraulis anchoita inhabited the Plata Plume Water. At the slope, Tropical Water was characterized by the bristlemouth Cyclothone acclinidens. The concurrent analysis showed the importance of both cross-shelf and latitudinal gradients on the large-scale distribution of larval fish species. Our findings reveal that ichthyoplankton composition and large-scale spatial distribution are determined by water mass composition in both latitudinal and cross-shelf gradients.

Evidence for a maximum mass cut-off in the neutron star mass distribution and constraints on the equation of state

Science.gov (United States)

Alsing, Justin; Silva, Hector O.; Berti, Emanuele

2018-04-01

We infer the mass distribution of neutron stars in binary systems using a flexible Gaussian mixture model and use Bayesian model selection to explore evidence for multi-modality and a sharp cut-off in the mass distribution. We find overwhelming evidence for a bimodal distribution, in agreement with previous literature, and report for the first time positive evidence for a sharp cut-off at a maximum neutron star mass. We measure the maximum mass to be 2.0M⊙ sharp cut-off is interpreted as the maximum stable neutron star mass allowed by the equation of state of dense matter, our measurement puts constraints on the equation of state. For a set of realistic equations of state that support >2M⊙ neutron stars, our inference of mmax is able to distinguish between models at odds ratios of up to 12: 1, whilst under a flexible piecewise polytropic equation of state model our maximum mass measurement improves constraints on the pressure at 3 - 7 × the nuclear saturation density by ˜30 - 50% compared to simply requiring mmax > 2M⊙. We obtain a lower bound on the maximum sound speed attained inside the neutron star of c_s^max > 0.63c (99.8%), ruling out c_s^max c/√{3} at high significance. Our constraints on the maximum neutron star mass strengthen the case for neutron star-neutron star mergers as the primary source of short gamma-ray bursts.

Polystyrene nanoparticles facilitate the internalization of impermeable biomolecules in non-tumour and tumour cells from colon epithelium

Energy Technology Data Exchange (ETDEWEB)

Cabeza, Laura [University of Granada, Department of Human Anatomy and Embryology, Institute of Biopathology and Regenerative Medicine (IBIMER) (Spain); Cano-Cortés, Victoria; Rodríguez, María J. [University of Granada, Department of Pharmaceutical and Organic Chemistry (Spain); Vélez, Celia; Melguizo, Consolación, E-mail: melguizo@ugr.es [University of Granada, Department of Human Anatomy and Embryology, Institute of Biopathology and Regenerative Medicine (IBIMER) (Spain); Sánchez-Martín, Rosario M., E-mail: rmsanchez@ugr.es [University of Granada, Department of Pharmaceutical and Organic Chemistry (Spain); Prados, Jose [University of Granada, Department of Human Anatomy and Embryology, Institute of Biopathology and Regenerative Medicine (IBIMER) (Spain)

2015-01-15

Advanced colon cancer has a poor prognosis due to the limited effectiveness of current chemotherapies. Treatment failures may be avoided by the utilization of nanoparticles, which can enhance the effects of antitumor drugs, reduce their side effects and increase their directionality. Polystyrene nanoparticles have shown high biocompatibility and appropriate physicochemical properties and may represent a novel and more effective approach against colon cancer. In the present study, polystyrene nanoparticles were synthesized and fluorescently labelled, analyzing their cell internalization, intracellular localization and capacity to release transported molecules in tumour and non-tumour human colon cell lines (T84 and CCD-18). Flow cytometry and fluorescence microscopy studies demonstrated that polystyrene nanoparticles are an effective vehicle for the intracellular delivery of small molecules into colon epithelium cells. The percentage cell uptake was around 100 % in both T84 and CCD-18 cell lines after only 24 h of exposure and was cell confluence-independent. The polystyrene nanoparticles showed no cytotoxicity in either colon cell line. It was found that small molecules can be efficiently delivered into colon cells by using a disulphide bridge as release strategy. Analysis of the influence of the functionalization of the polystyrene nanoparticles surface on the internalization efficiency revealed some morphological changes in these cells. These results demonstrate that polystyrene nanoparticles may improve the transport of biomolecules into colon cells which could have a potential application in chemotherapeutic treatment against colon cancer.

Polystyrene nanoparticles facilitate the internalization of impermeable biomolecules in non-tumour and tumour cells from colon epithelium

International Nuclear Information System (INIS)

Cabeza, Laura; Cano-Cortés, Victoria; Rodríguez, María J.; Vélez, Celia; Melguizo, Consolación; Sánchez-Martín, Rosario M.; Prados, Jose

2015-01-01

Advanced colon cancer has a poor prognosis due to the limited effectiveness of current chemotherapies. Treatment failures may be avoided by the utilization of nanoparticles, which can enhance the effects of antitumor drugs, reduce their side effects and increase their directionality. Polystyrene nanoparticles have shown high biocompatibility and appropriate physicochemical properties and may represent a novel and more effective approach against colon cancer. In the present study, polystyrene nanoparticles were synthesized and fluorescently labelled, analyzing their cell internalization, intracellular localization and capacity to release transported molecules in tumour and non-tumour human colon cell lines (T84 and CCD-18). Flow cytometry and fluorescence microscopy studies demonstrated that polystyrene nanoparticles are an effective vehicle for the intracellular delivery of small molecules into colon epithelium cells. The percentage cell uptake was around 100 % in both T84 and CCD-18 cell lines after only 24 h of exposure and was cell confluence-independent. The polystyrene nanoparticles showed no cytotoxicity in either colon cell line. It was found that small molecules can be efficiently delivered into colon cells by using a disulphide bridge as release strategy. Analysis of the influence of the functionalization of the polystyrene nanoparticles surface on the internalization efficiency revealed some morphological changes in these cells. These results demonstrate that polystyrene nanoparticles may improve the transport of biomolecules into colon cells which could have a potential application in chemotherapeutic treatment against colon cancer

Synthesis of amylose-block-polystyrene rod-coil block copolymers

NARCIS (Netherlands)

Loos, Katja; Stadler, Reimund

1997-01-01

In the present communication we demonstrate the synthesis of a hybrid block copolymer based on the combination of a biopolymer (amylose) with a synthetic block (polystyrene). To obtain such materials, amino-functionalized polymers were modified with maltoheptaose moieties that serve as initiators

One-step routes from di- and triblock copolymer precursors to hydrophilic nanoporous poly(acrylic acid)-b-polystyrene

DEFF Research Database (Denmark)

Guo, Fengxiao; Jankova Atanasova, Katja; Schulte, Lars

2008-01-01

Nanoporous polystyrene with hydrophilic pores was prepared from di- and triblock copolymer precursors. The precursor material was either a poly(tert-butyl acryl ate)-b-polystyrene (PtBA-b-PS) diblock copolymer synthesized by atom transfer radical polymerization (ATRP) or a polydimethylsiloxane......-b-poly(tertbutyl acrylate)-b-polystyrene (PDMS-b-PtBA-b-PS) triblock copolymer synthesized by a combination of living anionic polymerization and ATRP. In the latter copolymer, PS was the matrix and mechanically stable component, PtBA was converted by acidic deprotection to hydrophilic poly(acrylic acid) (PAA) providing...

Extruded expanded polystyrene sheets coated by TiO{sub 2} as new photocatalytic materials for foodstuffs packaging

Energy Technology Data Exchange (ETDEWEB)

Loddo, V.; Marci, G. [Schiavello-Grillone Photocatalysis Group - Dipartimento di Ingegneria Elettrica, Elettronica e delle Telecomunicazioni, di tecnologie Chimiche, Automatica e modelli Matematici - Universita degli Studi di Palermo, Viale delle Scienze (Ed. 6) - 90128 Palermo (Italy); Palmisano, G., E-mail: giovanni_palmisano@yahoo.it [Schiavello-Grillone Photocatalysis Group - Dipartimento di Ingegneria Elettrica, Elettronica e delle Telecomunicazioni, di tecnologie Chimiche, Automatica e modelli Matematici - Universita degli Studi di Palermo, Viale delle Scienze (Ed. 6) - 90128 Palermo (Italy); Yurdakal, S. [Kimya Boeluemue, Fen-Edebiyat Fakueltesi, Afyon Kocatepe Ueniversitesi - Ahmet Necdet Sezer Kampuesue - 03200 Afyon (Turkey); Brazzoli, M.; Garavaglia, L. [Sirap-Gema S.p.A. - Via Industriale, 1/3 - 25028 Verolanuova (Brescia) (Italy); Palmisano, L., E-mail: leonardo.palmisano@unipa.it [Schiavello-Grillone Photocatalysis Group - Dipartimento di Ingegneria Elettrica, Elettronica e delle Telecomunicazioni, di tecnologie Chimiche, Automatica e modelli Matematici - Universita degli Studi di Palermo, Viale delle Scienze (Ed. 6) - 90128 Palermo (Italy)

2012-11-15

Highlights: Black-Right-Pointing-Pointer An extruded polystyrene has been functionalised by TiO{sub 2}. Black-Right-Pointing-Pointer A photocatalytic polymer has been developed via a sol-gel method. Black-Right-Pointing-Pointer Thermoformed packagings for foodstuffs application have been prepared. - Abstract: Nanostructured, photoactive anatase TiO{sub 2} sol prepared under very mild conditions using titanium tetraisopropoxide as the precursor is used to functionalise extruded expanded polystyrene (XPS) sheets by spray-coating resulting in stable and active materials functionalised by TiO{sub 2} nanoparticles. Photocatalytic tests of these sheets performed in a batch reactor in gas-solid system under UV irradiation show their successful activity in degrading probe molecules (2-propanol, trimethylamine and ethene). Raman spectra ensure the deposition of TiO{sub 2} as crystalline anatase phase on the polymer surface. The presence of TiO{sub 2} with respect to polymer surface can be observed in SEM images coupled to EDAX mapping allowing to monitor the surface morphology and the distribution of TiO{sub 2} particles. Finally thermoforming of these sheets in industrial standard equipment leads to useful containers for foodstuffs.

Radial distributions of surface mass density and mass-to-luminosity ratio in spiral galaxies

Science.gov (United States)

Sofue, Yoshiaki

2018-03-01

We present radial profiles of the surface mass density (SMD) in spiral galaxies directly calculated using rotation curves of two approximations of flat-disk (SMD-F) and spherical mass distribution (SMD-S). The SMDs are combined with surface brightness using photometric data to derive radial variations of the mass-to-luminosity ratio (ML). It is found that the ML generally has a central peak or a plateau, and decreases to a local minimum at R ˜ 0.1-0.2 h, where R is the radius and h is the scale radius of optical disk. The ML, then, increases rapidly until ˜0.5 h, and is followed by gradual rise till ˜2 h, remaining at around ˜2 [M_{⊙} L^{-1}_{⊙}] in the w1 band (infrared λ3.4 μm) and ˜ 10 [M_⊙ L_⊙ ^{-1}] in the r band (λ6200-7500 Å). Beyond this radius, the ML increases steeply with approaching the observed edges at R ˜ 5 h, attaining to as high values as ˜20 in w1 and ˜ 10^2 [M_⊙ L_⊙ ^{-1}] in the r band, which are indicative of dominant dark matter. The general properties of the ML distributions will be useful for constraining cosmological formation models of spiral galaxies.

Proton conducting sulphonated fluorinated poly(styrene) crosslinked electrolyte membranes

Energy Technology Data Exchange (ETDEWEB)

Soules, A.; Ameduri, B.; Boutevin, B.; David, G. [Institut Charles Gerhardt UMR CNRS 5253 Equipe, Ingenierie et Architectures Macromoleculaires,' ' Ecole Nationale Superieure de Chimie de Montpellier, 8 rue de l' Ecole Normale, 34296 Montpellier, Cedex 05 (France); Perrin, R. [CEA Le Ripault Departement des Materiaux, DMAT/SCMF/LSTP, BP16 - 37260 Monts (France); Gebel, G. [Structure et Proprietes des Architectures Moleculaires UMR 5819 (CEA-CNRS-UJF), INAC, SPrAM, CEA Grenoble, 17 Rue des Martyrs, 38054 Grenoble, Cedex 9 (France)

2011-10-15

Potential membranes for polymer electrolyte membrane fuel cell based on crosslinked sulphonated fluorinated polystyrenes (PS) were synthesised in two steps. First, azide-telechelic polystyrene was obtained by iodine transfer polymerisation of styrene in the presence of 1,6-diiodoperfluorohexane followed by azido chain-end functionalisation. Then azide-telechelic polystyrene was efficiently crosslinked with 1,10-diazido-1H,1H,2H,2H,9H,9H,10H,10H-perfluorodecane under UV irradiation. After 45 min only, almost completion of azide crosslinking could be achieved, resulting in crosslinked membranes with insoluble fractions higher than 95%. The sulphonation of the crosslinked membranes afforded ionic exchange capacities (IECs) ranging from 2.2 to 3.2 meq g{sup -1}. The hydration number was shown to be very high (from 30 to 75), depending on both the content of perfluorodecane and of sulphonic acid groups. The morphology of the membranes, assessed by small-angle X-ray scattering, was found to be a lamellar-type structure with two types of ionic domains. For the membrane that exhibited an IEC value of 2.2 meq.g{sup -1}, proton conductivity was in the same range as that of Nafion {sup registered} (120-135 mS.cm{sup -1}), whereas the membrane IEC value of 3.2 meq.g{sup -1} showed a proton conductivity higher than that of Nafion {sup registered} in liquid water from 25 to 80 C, though a high water uptake. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Diameter measurements of polystyrene particles with atomic force microscopy

International Nuclear Information System (INIS)

Garnaes, J

2011-01-01

The size of (nano) particles is a key parameter used in controlling their function. The particle size is also important in order to understand their physical and chemical properties and regulate their number in health and safety issues. In this work, the geometric diameters of polystyrene spheres of nominal diameter 100 nm are measured using atomic force microscopy. The measurements are based on the apex height and on the average distance between neighbouring spheres when they form a close-packed monolayer on a flat mica substrate. The most important influence parameters for the determination of the geometric diameter are the lateral air gaps and deformation of the spheres. The lateral air gaps are caused by significant size variations of the individual spheres, and a correction is calculated based on the simulation of packing of spheres. The deformation of the spheres is caused mainly by capillary forces acting when they are in contact with each other or with the mica substrate. Based on calculated capillary forces and the literature values of the elastic properties of the polystyrene and mica, the deformation is estimated to be 2 nm with a standard uncertainty of 2 nm. The geometric diameter of the polystyrene spheres was measured with a combined standard uncertainty of ≈3 nm. The measured vertical diameter of 92.3 nm and the certified mobility equivalent diameter measured by differential mobility analysis (DMA) are marginally consistent at a confidence level of 95%. However, the measured lateral geometric diameter was 98.9 nm and is in good agreement with DMA

Coupling of mass and charge distributions for low excited nuclear fission

International Nuclear Information System (INIS)

Salamatin, V.S.; )

2000-01-01

The simple model for calculation of charge distributions of fission fragments for low exited nuclear fission from experimental mass distributions is offered. The model contains two parameters, determining amplitude of even-odd effect of charge distributions and its dependence on excitation energy. Results for reactions 233 U(n th ,f), 235 U(n th ,f), 229 Th(n th ,f), 249 Cf(n th ,f) are spent [ru

SYNTHESIS AND POLYMERIZATION OF α-METHACRYLYOXYL-ETHYLOXYCARBONYLMETHYL- ω-(N,N-DIETHYLDITHIOCARBAMYL) POLYSTYRENE MACROMONOMERS

Institute of Scientific and Technical Information of China (English)

Shu-hui Qin; Kun-yuan Qiu

2000-01-01

Polystyrene macromonomers with different molecular weight were prepared by radical polymerization of styrene (St) in benzene using β-methacryloxylethyl 2-N,N-diethyldithiocarbamylacetate (MAEDCA) as a monomer-iniferter.Characterization of the macromonomer by 1H-NMR showed that the end groups were α-methacrylyoxylethyloxycarbonyl-methyl and ω-(N,N-diethyldithiocarbamyl). The macromonomer was difficult to homopolymerize, but it was easily copolymerized with methyl methacrylate (MMA) initiated by AIBN to form graft copolymers (PMMA-g-PSt) with PSt branches randomly distributed along the PMMA backbone. Copolymerization reaction and the structure of the graft copolymers were strongly affected by Mn and concentration of the macromonomer. The composition and Mn of the purified graft copolymer were determined by 1H-NMR and GPC analysis.

Low cost plastic scintillator by using commercial polystyrene

International Nuclear Information System (INIS)

Oktar, O.; Ari, G.; Guenduez, O.; Demirel, H.; Demirbas, A.

2009-01-01

Plastic scintillation detectors have been used in nuclear and high energy physics for many decades. Among their benefits are fast response, ease of manufacture and versatility. Their main drawbacks are radiation resistance and cost. Plastic Scintillators can be described as solid materials which contain organic fluorescent compounds dissolved within a polymer matri10. Transparent plastics commonly used for light scintillation are Polystyrene (or PS, poly-vinyl-benzene) and polyvinyl-toluene (or PVT, poly-methyl-styron). In this activity, preliminary studies for low cost plastic scintillator production by using commercial polystyrene pellets and extrusion method were aimed. For this purpose, PS blocks consist of commercial fluorescent dopant were prepared by an extruder in SANAEM. Molds suitable for extruder were designed and manufactured and optimum production parameters such as extrusion temperature profile, extrusion rate and pressure were obtained. Plastic blocks prepared were optically and mechanically tested and its response against various radioactive sources was measured.This study has shown that plastic scintillators imported can be produced in SANAEM domestically and be used for detection of radioactive materials within the country or border gates.

PARTICLEBOARDS PRODUCED WITH Eucalyptus grandis W. Hill ex Maiden POLYSTYRENE AND POLYETHYLENE THEREPHTHALATE PARTICLES

Directory of Open Access Journals (Sweden)

Antônio da Silva Maciel

2004-06-01

Full Text Available This research investigated the properties of wood particleboards, containing particles of polystyrene (PS and polyethylene therephthalate (PET. Particleboards were produced with 0%, 25% or 50% of polystyrene and 100%, 75% or 50% of Eucalyptus grandis particles. Additional boards were produced with two amounts of PET/PS (5/20% or 10/40% and 75% or 50% wood particles. As binding agents three amounts (0%, 4% or 6% of urea-formaldehyde or phenol-formaldehyde adhesive and three amounts of polystyrene in toluene solution (0%, 4% or 6% were used. One-layer boards, measuring approximately 400,0 x 400,0 x 10,0 mm with density approximately equal to 0,60 g/cm3, were produced. Internal bond, modulus of rupture and elasticity, screw withdrawal, as well water absorption and thickness swelling, after 24 hours of immersion were determined. All mechanical boards’ properties were superior to the established by ANSI/A 208.1-1993 standards. All wood/plastic particleboards absorbed more water then those observed in commercial boards. However the observed thickness swelling was quite similar to the values of commercial wood particleboards. Boards in which the solution of polystyrene was applied were, in general, presented the best values for all properties.

Increased adsorption of histidine-tagged proteins onto tissue culture polystyrene

DEFF Research Database (Denmark)

Holmberg, Maria; Hansen, Thomas Steen; Lind, Johan Ulrik

2012-01-01

and ethylenediaminetetraacetic acid (EDTA), as well as adsorption performed at different pH and ionic strength indicates that the high adsorption is caused by electrostatic interaction between negatively charged carboxylate groups on the TCPS surface and positively charged histidine residues in the proteins. Pre......In this study we compare histidine-tagged and native proteins with regards to adsorption properties. We observe significantly increased adsorption of proteins with an incorporated polyhistidine amino acid motif (HIS-tag) onto tissue culture polystyrene (TCPS) compared to similar proteins without...... a HIS-tag. The effect is not observed on polystyrene (PS). Adsorption experiments have been performed at physiological pH (7.4) and the effect was only observed for the investigated proteins that have pI values below or around 7.4. Competitive adsorption experiments with imidazole...

Polystyrene cryostat facilitates testing tensile specimens under liquid nitrogen

Science.gov (United States)

Shogan, R. P.; Skalka, R. J.

1967-01-01

Lightweight cryostat made of expanded polystyrene reduces eccentricity in a tensile system being tested under liquid nitrogen. The cryostat is attached directly to the tensile system by a special seal, reducing misalignment effects due to cryostat weight, and facilitates viewing and loading of the specimens.

Rheological Behavior of Entangled Polystyrene-Polyhedral Oligosilsesquioxane (POSS) Copolymer

National Research Council Canada - National Science Library

Wu, Jian; Mather, Patrick T; Haddad, Timothy S; Kim, Gyeong-Man

2006-01-01

...: random copolymers of polystyrene (PS) and styryl-based polyhedral oligosilsesquioxane (POSS), R7(Si8O12)(C6H4CH=CH2), with R = isobutyl (iBu). A series of styrene-styryl POSS random copolymers with 0, 6, 15, 30, 50 wt...

Formation of fission-fragment mass distribution for nuclei lighter than thorium

International Nuclear Information System (INIS)

Itkis, M.G.; Mul'gin, S.I.; Rusanov, A.Y.; Okolovich, A.N.; Smirenkin, G.N.

1986-01-01

A phenomenological approach to description of fission-fragment mass distribution Y(M) for nuclei in the vicinity of Pb is developed and used to extract from the experimental Y(M) data the nuclear deformation potential energy V(M) and its components: the macroscopic (liquid-drop) part and the shell correction in the transition state. The results of the analysis are compared with the theoretically obtained V(M) and Y(M). The three-hump fragment-mass distributions observed in Ra fission are satisfactorily described within the framework of the approach developed. The properties of the symmetric and asymmetric fission valleys and the related Y(M) components are discussed

Fragment Size Distribution of Blasted Rock Mass

Science.gov (United States)

Jug, Jasmin; Strelec, Stjepan; Gazdek, Mario; Kavur, Boris

2017-12-01

Rock mass is a heterogeneous material, and the heterogeneity of rock causes sizes distribution of fragmented rocks in blasting. Prediction of blasted rock mass fragmentation has a significant role in the overall economics of opencast mines. Blasting as primary fragmentation can significantly decrease the cost of loading, transport, crushing and milling operations. Blast fragmentation chiefly depends on the specific blast design (geometry of blast holes drilling, the quantity and class of explosive, the blasting form, the timing and partition, etc.) and on the properties of the rock mass (including the uniaxial compressive strength, the rock mass elastic Young modulus, the rock discontinuity characteristics and the rock density). Prediction and processing of blasting results researchers can accomplish by a variety of existing software’s and models, one of them is the Kuz-Ram model, which is possibly the most widely used approach to estimating fragmentation from blasting. This paper shows the estimation of fragmentation using the "SB" program, which was created by the authors. Mentioned program includes the Kuz-Ram model. Models of fragmentation are confirmed and calibrated by comparing the estimated fragmentation with actual post-blast fragmentation from image processing techniques. In this study, the Kuz-Ram fragmentation model has been used for an open-pit limestone quarry in Dalmatia, southern Croatia. The resulting calibrated value of the rock factor enables the quality prognosis of fragmentation in further blasting works, with changed drilling geometry and blast design parameters. It also facilitates simulation in the program to optimize blasting works and get the desired fragmentations of the blasted rock mass.

Mass and Angular Distributions of Charged Dihadron Production

Energy Technology Data Exchange (ETDEWEB)

Cummings, Mary Clare [Michigan U.

1990-01-01

Experiment 711, conducted at Fermilab. provided a unique handle towards understanding valence quark scattering by studying pairs of single. charged, high transverse momentum hadrons produced in collisions of 800 GeV /c protons on fixed metal targets. The apparatus consisted of a double-arm spectrometer. calorimetrically triggered. with high momentum resolution and a large angular acceptance for all charge states of particle pairs. The experiment was designed to select those hadron pairs that carrted most of the momentum and energy of the underlying scattered quarks and gluons. The charge of such "leading" hadrons is correlated with the charge of the quark that produced it. Quantum Chromodynamics (QCD) assumes that the scattering behavior of quarks ts independent of their charge, or "flavour": Experiment 711 could test this assumption. Tilis dissertation descrtbes the analysis of the mass and angular distributions of hadron pair production for three separate charge states: +-, ++ and --. The angular distributions are found to deviate from theory predictions of flavour symmetry. Also. the mass cross sections indicate ratios of positive to negative hard-scattered particles that are larger than expected from theory. These results could warrant reconsideration of the assumptions and approximations currently made in leading-order QCD calculations.

Analysis for mass distribution of proton-induced reactions in intermediate energy range

CERN Document Server

Xiao Yu Heng

2002-01-01

The mass and charge distribution of residual products produced in the spallation reactions needs to be studied, because it can provide useful information for the disposal of nuclear waste and residual radioactivity generated by the spallation neutron target system. In present work, the Many State Dynamical Model (MSDM) is based on the Cascade-Exciton Model (CEM). The authors use it to investigate the mass distribution of Nb, Au and Pb proton-induced reactions in energy range from 100 MeV to 3 GeV. The agreement between the MSDM simulations and the measured data is good in this energy range, and deviations mainly show up in the mass range of 90 - 150 for the high energy proton incident upon Au and Pb

Langevin description of mass distributions of fragments originating from the fission of excited nuclei

International Nuclear Information System (INIS)

Vanin, D.V.; Nadtochy, P.N.; Adeev, G.D.; Kosenko, G.I.

2000-01-01

A stochastic approach to fission dynamics is proposed. The approach, which is based on Langevin equations, is used to calculate the mass distributions of fragments originating from the fission of excited nuclei. The effect of viscosity and light-particle emission on the variance of mass distributions is studied. The results of the calculations based on the above approach reveal that, in order to obtain a simultaneous description of mass-distribution parameters and the multiplicities of prescission particles, it is necessary to use sufficiently large values of nuclear viscosity both for the one-body and for the two-body viscosity mechanism, anomalously large values of the viscosity coefficient being required in the latter case

Adsorption of lysozyme unto silica and polystyrene surfaces in ...

African Journals Online (AJOL)

The adsorption capacity of lysozyme (chicken egg white) from aqueous solutions unto silica and polystyrene interfaces was studied at varying lysozyme concentrations and ionic strength. The studies revealed an increase in adsorption capacity with increase in concentration and with maximum adsorption densities of 1.34 ...

BINARY FORMATION MECHANISMS: CONSTRAINTS FROM THE COMPANION MASS RATIO DISTRIBUTION

International Nuclear Information System (INIS)

Reggiani, Maddalena M.; Meyer, Michael R.

2011-01-01

We present a statistical comparison of the mass ratio distribution of companions, as observed in different multiplicity surveys, to the most recent estimate of the single-object mass function. The main goal of our analysis is to test whether or not the observed companion mass ratio distribution (CMRD) as a function of primary star mass and star formation environment is consistent with having been drawn from the field star initial mass function (IMF). We consider samples of companions for M dwarfs, solar-type stars, and intermediate-mass stars, both in the field as well as clusters or associations, and compare them with populations of binaries generated by random pairing from the assumed IMF for a fixed primary mass. With regard to the field we can reject the hypothesis that the CMRD was drawn from the IMF for different primary mass ranges: the observed CMRDs show a larger number of equal-mass systems than predicted by the IMF. This is in agreement with fragmentation theories of binary formation. For the open clusters α Persei and the Pleiades we also reject the IMF random-pairing hypothesis. Concerning young star-forming regions, currently we can rule out a connection between the CMRD and the field IMF in Taurus but not in Chamaeleon I. Larger and different samples are needed to better constrain the result as a function of the environment. We also consider other companion mass functions and we compare them with observations. Moreover the CMRD both in the field and clusters or associations appears to be independent of separation in the range covered by the observations. Combining therefore the CMRDs of M (1-2400 AU) and G (28-1590 AU) primaries in the field and intermediate-mass primary binaries in Sco OB2 (29-1612 AU) for mass ratios, q = M 2 /M 1 , from 0.2 to 1, we find that the best chi-square fit follows a power law dN/dq∝q β , with β = -0.50 ± 0.29, consistent with previous results. Finally, we note that the Kolmogorov-Smirnov test gives a ∼1

A study of jet mass distributions with grooming

Science.gov (United States)

Marzani, Simone; Schunk, Lais; Soyez, Gregory

2017-07-01

We perform a phenomenological study of the invariant mass distribution of hadronic jets produced in proton-proton collisions, in conjunction with a grooming algorithm. In particular, we consider the modified MassDrop Tagger (mMDT), which corresponds to Soft Drop with angular exponent β = 0. Our calculation, which is differential in both jet mass and jet transverse momentum, resums large logarithms of the jet mass, including the full dependence on the groomer's energy threshold z cut, and it is matched to fixed-order QCD matrix elements at next-to-leading order. In order to account for non-perturbative contributions, originating from the hadronisation process and from the underlying event, we also include a phenomenological correction factor derived from Monte Carlo parton shower simulations. Furthermore, we consider two different possibilities for the jet transverse momentum: before or after grooming. We show that the former should be preferred for comparisons with upcoming experimental data essentially because the mMDT transverse momentum spectrum is not collinear safe, though the latter exhibits less sensitivity to underlying event and displays properties that may provide complementary information for probing non-perturbative effects.

The properties of water in swollen cross-linked polystyrene sulfo acids

Science.gov (United States)

Gagarin, A. N.; Tokmachev, M. G.; Kovaleva, S. S.; Ferapontov, N. B.

2008-11-01

The properties of water in polystyrene sulfo acid gels with various cross-linking degrees were studied by optical volumetry and dynamic desorption porosimetry. The isotherms of water desorption obtained by dynamic desorption porosimetry coincided with isopiestic isotherms, which allowed this method to be recommended for the determination of the amount of water in polymer gels. Joint optical volumetry and dynamic desorption porosimetry studies showed that the interphase boundary in the cross-liked hydrophilic polymer-water system did not coincide with the visible gel boundary, because gels were two-phase systems, which contained water of two types, “free” and “bound.” The influence of the degree of polymer cross-linking on the amounts and properties of water of the two types was studied. It was shown that constants of water distribution in the polymer could be calculated from the dynamic desorption porosimetry data.

Distribution of mass in the planetary system and solar nebulae

Energy Technology Data Exchange (ETDEWEB)

Weidenschilling, S J [Carnegie Institution of Washington, D.C. (USA). Dept. of Terrestrial Magnetism

1977-09-01

A model 'solar nebula' is constructed by adding the solar complement of light elements to each planet, using recent models of planetary compositions. Uncertainties in this approach are estimated. The computed surface density varies approximately as rsup(-3/2). Mercury, Mars and the asteroid belt are anomalously low in mass, but processes exist which would preferentially remove matter from these regions. Planetary masses and compositions are generally consistent with a monotonic density distribution in the primordial solar nebula.

Modelling of Radiolytical Proceses in Polystyrenic Structures

International Nuclear Information System (INIS)

Postolache, C.

2006-01-01

The behavior of polystyrene, poly α-methylstyrene and poly β-methylstyrene structures in ionizing fields was analyzed using computational methods. In this study, the primary radiolytic effect was evaluated using a free radical mechanism. Molecular structures were built and geometrical optimized using quantum-chemical methods. Binding energies for different quantum states and peripheral orbitals distribution were determined. Based on obtained results it was proposed an evaluation model of radiolytical processes in polymers in solid phase. Suggested model suppose to distinguish the dominant processes by binding energies values analysis and LUMO peripheral orbital distribution. Computed binding energies analysis of energetically optimized molecular structures in ionized state (charge +1, multiplicity 2) reveals a high similitude of obtained binding energies for ionized states. The same similitude was observed also in case of total binding energies for neutral state (charge 0, multiplicity 1). Analyzed molecular structures can be associated with ionized molecule state right after one electron capture. This fact suggests that the determined stage of radiolitical fragmentation act is intermediate state of ionized molecule. This molecule captured one electron but it had no necessary time for atoms rearrangement in the molecule for new quantum state. This supposition is in accordance with literature, the time period between excitation act and fragmentation act being lower than 10 - 15 seconds. Based on realized model could be explained the behavior differences of polymeric structures in ionizing radiation field. Preferential fracture of main chains in fragmentation poly α-methylstirene can be explained in accordance with proposed model by C-C from main C bonding energies decreasing in the neighboring of quaternary C

Evaluation of mass distribution data from 252Cf spontaneous fission

International Nuclear Information System (INIS)

Liu Tingjin

2003-01-01

The mass distribution data of 252 Cf spontaneous fission were evaluated based on 7 sets of available experimental data. The measured data were corrected for the standards and γ intensity used by using the new evaluated ones. The errors were made necessary adjusting. The evaluated experimental data were fitted with spline function without any restriction and with symmetric restriction. These two sets of fit data were recommended as reference data of the mass distribution of 252 Cf spontaneous fission. The errors of the recommended data were considerably reduced comparing with the measured ones. The light and heavy peaks are not completely symmetric. Also there are fine structures on the right side of the light peak at A=109-111 and left side of the heavy peak at A=137-139. These should be paid attention and studied further. (author)

Effect of γ-ray irradiation on polystyrene, poly (methyl methacrylate), and their copolymer prepared by cast polymerization

International Nuclear Information System (INIS)

Tsukame, Takahiro; Kutsuzawa, Michio; Saitoh, Hideki; Shibasaki, Yoshio

1998-01-01

Effect of γ-ray irradiation on polystyrene (PS), poly(methyl methacrylate) (PMMA), and their copolymer prepared by cast polymerization was studied using size exclusion chromatography. The main chemical reactions in irradiated polymers were crosslinking and scission. Conversion of all irradiated samples increased regardless of the concentration of initiator (AIBN) used for cast polymerization. On γ-ray irradiation, the molecular weight of PS increased and its distribution broadened, whereas the molecular weight of PMMA decreased. These phenomena should be attributable to the competitive occurrence of scission and crosslinking in PS by γ-ray irradiation, whereas scission occurred mainly in PMMA. (author)

Syntheses, Magnetic and Spectral Studies on the Coordination Compounds of the Polystyrene-anchored Thiazolidin-4-one

Directory of Open Access Journals (Sweden)

Dinesh Kumar

2012-01-01

Full Text Available The reaction between polystyrene 3-formylsalicylate and thiophene-2-carboxylic acid hydrazide in DMF in the presence of ethyl acetate results in the formation of polystyrene N-(2-carbamoylthienyl-3'-carboxy-2'-hydroxybenzylideneimine (I. A benzene suspension of I reacts with mercaptoacetic acid and forms the polystyrene N-(2-carbamoylthienyl-C-(3'-carboxy-2'-hydroxyphenyl thiazolidin-4-one, PSCH2–LH2 (II. A DMF suspension of II reacts with Zn(II, Co(II, Cu(II, Zr(OH2(IV and MoO2(VI ions and forms the corresponding polystyrene-anchored coordination compounds, [PSCH2–LZn(DMF] (III, [PSCH2–LCo(DMF3] (IV, [PSCH2–LHCu(OAc] (V, [PSCH2–LH2Zr(OH2(OAc2] (VI and [PSCH2–LHMoO2(acac] (VII respectively. The polystyrene-anchored coordination compounds have been characterized on the basis of elemental analyses, spectral (IR, reflectance, ESR studies and magnetic susceptibility measurements. II acts as a neutral tridentate ONS donor ligand in VI, a monobasic bidentate OS donor ligand in VII, a monobasic tridentate ONS donor ligand in V and a dibasic tridentate ONO donor ligand in III and IV. The acetato groups behave as monodentate ligands in V and VI. A square-planar structure for V, a tetrahedral structure for III, an octahedral structure for IV and VII and a pentagonal-bipyramidal structure for VI are suggested.

Cognitive load in distributed and massed practice in virtual reality mastoidectomy simulation.

Science.gov (United States)

Andersen, Steven Arild Wuyts; Mikkelsen, Peter Trier; Konge, Lars; Cayé-Thomasen, Per; Sørensen, Mads Sølvsten

2016-02-01

Cognitive load theory states that working memory is limited. This has implications for learning and suggests that reducing cognitive load (CL) could promote learning and skills acquisition. This study aims to explore the effect of repeated practice and simulator-integrated tutoring on CL in virtual reality (VR) mastoidectomy simulation. Prospective trial. Forty novice medical students performed 12 repeated virtual mastoidectomy procedures in the Visible Ear Simulator: 21 completed distributed practice with practice blocks spaced in time and 19 participants completed massed practice (all practices performed in 1 day). Participants were randomized for tutoring with the simulator-integrated tutor function. Cognitive load was estimated by measuring reaction time in a secondary task. Data were analyzed using linear mixed models for repeated measurements. The mean reaction time increased by 37% during the procedure compared with baseline, demonstrating that the procedure placed substantial cognitive demands. Repeated practice significantly lowered CL in the distributed practice group but not in massed practice group. In addition, CL was found to be further increased by 10.3% in the later and more complex stages of the procedure. The simulator-integrated tutor function did not have an impact on CL. Distributed practice decreased CL in repeated VR mastoidectomy training more consistently than was seen in massed practice. This suggests a possible effect of skills and memory consolidation occurring over time. To optimize technical skills learning, training should be organized as time-distributed practice rather than as a massed block of practice, which is common in skills-training courses. N/A. © 2015 The American Laryngological, Rhinological and Otological Society, Inc.

The distribution of mass for spiral galaxies in clusters and in the field

International Nuclear Information System (INIS)

Forbes, D.A.; Whitmore, B.C.

1989-01-01

A comparison is made between the mass distributions of spiral galaxies in clusters and in the field using Burstein's mass-type methodology. Both the H-alpha emission-line rotation curves and more extended H I rotation curves are used. The fitting technique for determining mass types used by Burstein and coworkers has been replaced by an objective chi-sq method. Mass types are shown to be a function of both the Hubble type and luminosity, contrary to earlier results. The present data show a difference in the distribution of mass types for spiral galaxies in the field and in clusters, in the sense that mass type I galaxies, where the inner and outer velocity gradients are similar, are generally found in the field rather than in clusters. This can be understood in terms of the results of Whitmore, Forbes, and Rubin (1988), who find that the rotation curves of galaxies in the central region of clusters are generally failing, while the outer galaxies in a cluster and field galaxies tend to have flat or rising rotation curves. 15 refs

Delineating fibronectin bioadhesive micropatterns by photochemical immobilization of polystyrene and poly(vinylpyrrolidone).

Science.gov (United States)

Sterner, Olof; Giazzon, Marta; Zürcher, Stefan; Tosatti, Samuele; Liley, Martha; Spencer, Nicholas D

2014-01-01

Bioadhesive micropatterns, capable of laterally confining cells to a 2D lattice, have proven effective in simulating the in vivo tissue environment. They reveal fundamental aspects of the role of adhesion in cell mechanics, proliferation, and differentiation. Here we present an approach based on photochemistry for the fabrication of synthetic polymer micropatterns. Perfluorophenyl azide (PFPA), upon deep-UV exposure, forms a reactive nitrene capable of covalently linking to a molecule that is in close proximity. PFPA has been grafted onto a backbone of poly(allyl amine), which readily forms a self-assembled monolayer on silicon wafers or glass. A film of polystyrene was applied by spin-coating, and by laterally confining the UV exposure through a chromium-on-quartz photomask, monolayers of polymers could be immobilized in circular microdomains. Poly(vinylpyrrolidone) (PVP) was attached to the background to form a barrier to nonspecific protein adsorption and cell adhesion. Micropatterns were characterized with high-lateral-resolution time-of-flight secondary ion mass spectrometry (TOF-SIMS), which confirmed the formation of polystyrene domains within a PVP background. Fluorescence-microscopy adsorption assays with rhodamine-labeled bovine serum albumin demonstrated the nonfouling efficiency of PVP and, combined with TOF-SIMS, allowed for a comprehensive characterization of the pattern geometry. The applicability of the micropatterned platform in single-cell assays was tested by culturing two cell types, WM 239 melanoma cells and SaOs-2 osteoblasts, on micropatterned glass, either with or without backfilling of the patterns with fibronectin. It was demonstrated that the platform was efficient in confining cells to the fibronectin-backfilled micropatterns for at least 48 h. PVP is thus proposed as a viable, highly stable alternative to poly(ethylene glycol) for nonfouling applications. Due to the versatility of the nitrene-insertion reaction, the platform could be

Thermal dewetting behavior of polystyrene composite thin films with organic-modified inorganic nanoparticles.

Science.gov (United States)

Kubo, Masaki; Takahashi, Yosuke; Fujii, Takeshi; Liu, Yang; Sugioka, Ken-ichi; Tsukada, Takao; Minami, Kimitaka; Adschiri, Tadafumi

2014-07-29

The thermal dewetting of polystyrene composite thin films with oleic acid-modified CeO2 nanoparticles prepared by the supercritical hydrothermal synthesis method was investigated, varying the nanoparticle concentration (0-30 wt %), film thickness (approximately 50 and 100 nm), and surface energy of silanized silicon substrates on which the composite films were coated. The dewetting behavior of the composite thin films during thermal annealing was observed by an optical microscope. The presence of nanoparticles in the films affected the morphology of dewetting holes, and moreover suppressed the dewetting itself when the concentration was relatively high. It was revealed that there was a critical value of the surface energy of the substrate at which the dewetting occurred. In addition, the spatial distributions of nanoparticles in the composite thin films before thermal annealing were investigated using AFM and TEM. As a result, we found that most of nanoparticles segregated to the surface of the film, and that such distributions of nanoparticles contribute to the stabilization of the films, by calculating the interfacial potential of the films with nanoparticles.

Compression behavior of cellular metals with inhomogeneous mass distribution

International Nuclear Information System (INIS)

Foroughi, B.

2001-05-01

Mechanical behavior of two types of closed cell metals (ALULIGHT and ALPORAS) is investigated experimentally and numerically. Compressive tests performed on prismatic specimens indicate that inhomogeneities in the mass density distribution are a key factor in the deformation behavior of cellular metals. The three dimensional cellular structure of the investigated specimens is recorded using x-ray medical computed tomography (CT). A special procedure called density mapping method has been used to transfer the recorded CT data into a continuum by averaging over a certain domain (averaging domain). This continuum model is implemented using finite elements to study the effect of variations in local mass densities. The finite element model is performed by a simple regular discretization of a specimen's volume with elements which have constant edge length. Mechanical properties derived from compression tests of ALPORAS samples are assigned to the corresponding mesoscopic density value of each element. The effect of averaging domain size is studied to obtain a suitable dimension which fulfils the homogenization requirements and allows the evaluation of inhomogenities in the specimens. The formation and propagation of deformation band(s) and stress-strain responses of tested cellular metals are modeled with respect to their mass distribution. It is shown that the inhomogeneous density distribution leads to plastic strain localization and causes a monotonically increase of the stress in the plateau regime although no hardening response was considered for homogeneous material in this regime. The simulated plastic strain localization and the calculated stress-strain responses are compared with the experimental results. The stiffness values of experiment and simulation agree very well for both cellular materials. The values of plateau strength as well, but it differs in some cases of ALULIGHT samples, where the hardening response can be predicted at least qualitatively

Preparation and Characterization of Polystyrene-Silver NanocompositeUsing MicroemulsionMethod and its Antibacterial Activity

Directory of Open Access Journals (Sweden)

A. Salabat

2014-07-01

Full Text Available Polymer nanocomposites containing metals have been used in a wide range of applications due to their versatility, and tunable characteristics including physical, chemical, biological and mechanical properties. In this research work polystyrene-silver nanocomposite has been produced using polymerization of a w/o microemulsion system. Styrene monomer was used as the oil or continues phase of the microemulsion system and polymerized following formation of Ag nanoparticles in the fluid medium. The UV-vis absorption and dynamic light scattering methods have been used to trace the growth process and size distribution of the Ag nanoparticles in the microemulsion system. Scanning electron microscopy (SEM was used to determine the morphology and particle size of the Ag particles in the synthesized nanocomposites.

Pyrolysis of virgin and waste polypropylene and its mixtures with waste polyethylene and polystyrene.

Science.gov (United States)

Kiran Ciliz, Nilgun; Ekinci, Ekrem; Snape, Colin E

2004-01-01

A comparison of waste and virgin polypropylene (PP) plastics under slow pyrolysis conditions is presented. Moreover, mixtures of waste PP with wastes of polyethylene (PE) and polystyrene (PS) were pyrolyzed under the same operating conditions. Not only the impact of waste on degradation products but also impacts of the variations in the mixing ratio were investigated. The thermogravimetric weight loss curves and their derivatives of virgin and waste PP showed differences due to the impurities which are dirt and food residues. The liquid yield distribution concerning the aliphatic, mono-aromatic and poly-aromatic compounds varies as the ratio of PP waste increases in the waste plastic mixtures. In addition to this, the alkene/alkane ratio of gas products shows variations depending on the mixing ratio of wastes.

The Role of Mucin in the Toxicological Impact of Polystyrene Nanoparticles

Directory of Open Access Journals (Sweden)

Iwona Inkielewicz-Stepniak

2018-05-01

Full Text Available The development of novel oral drug delivery systems is an expanding area of research and both new approaches for improving their efficacy and the investigation of their potential toxicological effect are crucial and should be performed in parallel. Polystyrene nanoparticles (NPs have been used for the production of diagnostic and therapeutic nanosystems, are widely used in food packaging, and have also served as models for investigating NPs interactions with biological systems. The mucous gel layer that covers the epithelium of the gastrointestinal system is a complex barrier-exchange system that it is mainly constituted by mucin and it constitutes the first physical barrier encountered after ingestion. In this study, we aimed to investigate the effect of polystyrene NPs on mucin and its potential role during NP–cell interactions. For this purpose, we evaluated the interaction of polystyrene NPs with mucin in dispersion by dynamic light scattering and with a deposited layer of mucin using a quartz crystal microbalance with dissipation technology. Next, we measured cell viability and the apoptotic state of three enterocyte-like cell lines that differ in their ability to produce mucin, after their exposure to the NPs. Positive charged NPs showed the ability to strongly interact and aggregate mucin in our model. Positive NPs affected cell viability and induced apoptosis in all cell lines independently of their ability of produce mucin.

The Interplay Between Fat Mass and Fat Distribution as Determinants of the Metabolic Syndrome Is Sex-Dependent.

Science.gov (United States)

Lind, Lars; Ärnlöv, Johan; Lampa, Erik

2017-09-01

Fat mass and fat distribution are major determinants of the metabolic syndrome (MetS), but the interplay between them has not been thoroughly investigated. In addition, fat mass and fat distribution are generally different in men than in women. We aimed to determine whether the interplay between fat mass and fat distribution regarding MetS and its components is sex-dependent using data from the large-scale population-based sample EpiHealth. Occurrence of MetS and its components was determined together with fat mass by bioimpedance in 19,094 participants in the EpiHealth sample [mean age 61 years (SD 8.5), 56% females]. MetS was defined by the NCEP/ATPIII-criteria. MetS prevalence was 23.0%. Fat mass (percent of body weight) was more strongly related to MetS (and the number of MetS components) in men than in women (P distribution on the fat mass versus MetS-relationship is stronger in women.

Mass distributions in nucleon-induced fission at intermediate energies

CERN Document Server

Duijvestijn, M C; Hambsch, F J

2001-01-01

Temperature-dependent fission barriers and fission-fragment mass distributions are calculated in the framework of the multimodal random neck-rupture model (MM-RNRM). It is shown how the distinction between the different fission modes disappears at higher excitation energies, due to the melting of shell effects. The fission-fragment mass yield calculations are coupled to the nuclear reaction code ALICE-91, which takes into account the competition between the other reaction channels and fission. With the combination of the temperature-dependent MM-RNRM and ALICE-91 nucleon-induced fission is investigated at energies between 10 and 200 MeV for nuclei varying from Au to Am. (72 refs).

Mass and charge distributions in Fe-induced reactions

International Nuclear Information System (INIS)

Madani, H.; Mignerey, A.C.; Marchetti, A.A.; Weston-Dawkes, A.P.; Kehoe, W.L.; Obenshain, F.

1995-01-01

The charge and mass of the projectile-like fragments produced in the 12-MeV/nucleon 56 Fe + 165 Ho reaction were measured at a laboratory scattering angle of 16 degrees. The mass and charge distributions of the projectile-like fragments were generated as a function of total kinetic energy loss (TKEL), and characterized by their neutron and proton centroids and variances, and correlation factors. A weak drift of the system towards mass asymmetry, opposite to the direction which minimizes the potential energy of the composite system, was observed. The increase in the variances with energy loss is consistent with a nucleon exchange mechanism as a means for energy dissipation. Predictions of two nucleon exchange models, Randrup's and, Tassan-Got's models, are compared to the experimental results of the 672-MeV 56 Fe + 165 Ho reaction and to other Fe-induced reactions. The proton and neutron centroids were found to be generally better reproduced by Tassan-Got's model than by Randrup's model. The variances and correlation factor are well reproduced for asymmetric systems by both models

Grafting of Polystyrene Chains at the Edge of Graphene Nanolayers by "Grafting Through" Approach Using Reversible Addition-Fragmentation Chain Transfer Polymerization

Directory of Open Access Journals (Sweden)

Hossein Roghani-Mamaqani

2017-09-01

Full Text Available Edge-functionalized graphene nanolayers with polystyrene chains were prepared by a “grafting through” reversible addition-fragmentation chain transfer (RAFT polymerization. For this purpose, double-bond containing modifier (MD was prepared. After edge-functionalization of graphene oxide (GO by two different amounts of MD and preparation of modified graphenes (LFG and HFG, RAFT polymerization of styrene was applied for preparation of functionalized GO with different densities of polystyrene chains. Fourier transform infrared spectroscopy showed that MD and polystyrene chains were grafted at the edge of GO. Gas chromatography showed that conversion decreased by the addition of modified GO content and also grafting density of MD. Number-average molecular weight and polydispersity index of polystyrene chains were derived from gel permeation chromatography. Increase of modified graphene content results in a decrease in molecular weight of attached polystyrene chains and also an increase in their PDI value. Increase of grafting density of MD results in decrease of molecular weight of polystyrene chains with no considerable variation in PDI value. Thermogravimetric analysis results showed that char residue is about 45.1 and 46.8% for LFG and HFG, respectively. The content of degradation ascribed to polystyrene increased with increase of grafting density of MD and decreased with increase of modified graphene content. X-ray diffraction results were used for evaluation of interlayer spacing of graphene layers after functionalization process and also study of nanocomposites structure. The results of scanning electron microscopy and transmission electron microscopy show that graphene layers with high clarity turned to opaque layers with lots of creases by oxidation and attachment of polystyrene chains.

Synthesis and characterization of the polystyrene - asphaltene graft copolymer BY FT-IR spectroscopy

International Nuclear Information System (INIS)

Leo, Adan Yovani; Salazar Ramiro

2008-01-01

The creation of new polymer compounds to be added to asphalt has drawn considerable attention because these substances have succeeded in modifying the asphalt rheological characteristics and physical properties for the enhancement of its behavior during the time of use. This work explains the synthesis of a new graft copolymer based on an asphalt fraction called asphaltene, modified with maleic anhydride. Polystyrene functionalization is conducted in a parallel fashion in order to obtain polybenzylamine resin with an amine - NH2 free group that reacts with the anhydride graft groups in the asphaltene, thus obtaining the new Polystyrene/Asphaltene graft copolymer

Biodegradation of weathered polystyrene films in seawater microcosms

OpenAIRE

Syranidou, Evdokia; Karkanorachaki, Katerina; Amorotti, Filippo; Franchini, Martina; Repouskou, Eftychia; Kaliva, Maria; Vamvakaki, Maria; Kolvenbach, Boris; Fava, Fabio; Corvini, Philippe F.-X.; Kalogerakis, Nicolas

2017-01-01

A microcosm experiment was conducted at two phases in order to investigate the ability of indigenous consortia alone or bioaugmented to degrade weathered polystyrene (PS) films under simulated marine conditions. Viable populations were developed on PS surfaces in a time dependent way towards convergent biofilm communities, enriched with hydrocarbon and xenobiotics degradation genes. Members of Alphaproteobacteria and Gammaproteobacteria were highly enriched in the acclimated plastic associate...

Molecular modeling and simulation of atactic polystyrene/amorphous silica nanocomposites

International Nuclear Information System (INIS)

Mathioudakis, I; Vogiatzis, G G; Tzoumanekas, C; Theodorou, D N

2016-01-01

The local structure, segmental dynamics, topological analysis of entanglement networks and mechanical properties of atactic polystyrene - amorphous silica nanocomposites are studied via molecular simulations using two interconnected levels of representation: (a) A coarse - grained level. Equilibration at all length scales at this level is achieved via connectivity - altering Monte Carlo simulations. (b) An atomistic level. Initial configurations for atomistic Molecular Dynamics (MD) simulations are obtained by reverse mapping well- equilibrated coarse-grained configurations. By analyzing atomistic MD trajectories, the polymer density profile is found to exhibit layering in the vicinity of the nanoparticle surface. The dynamics of polystyrene (in neat and filled melt systems) is characterized in terms of bond orientation. Well-equilibrated coarse-grained long-chain configurations are reduced to entanglement networks via topological analysis with the CReTA algorithm. Atomistic simulation results for the mechanical properties are compared to the experimental measurements and other computational works. (paper)

The influence of organo-bentonite clay on the processing and mechanical properties of nylon 6 and polystyrene composites

International Nuclear Information System (INIS)

Araujo, E.M.; Melo, T.J.A.; Santana, L.N.L.; Neves, G.A.; Ferreira, H.C.; Lira, H.L.; Carvalho, L.H.; A'vila, M.M.; Pontes, M.K.G.; Araujo, I.S.

2004-01-01

The influence of organoclay on the processing and mechanical properties of nylon 6 and polystyrene was investigated. A bentonite sample from Boa Vista/PB, Northeast of Brazil, was treated with alkyldimethylbenzylammonium chloride. After the treatment, the powder was characterized by thermal analysis and infrared spectroscopy. Composites were prepared by using a Torque rheometer. The results show the intercalation of quaternary ammonium salt in the structure of bentonite and organo-bentonite produced significant changes on the processing of the nylon 6 and polystyrene with increase in the viscosity and rigidity. However, the mechanical properties of polystyrene/organoclay system did not show significant changes

Elemental mass size distribution of the Debrecen urban aerosol

International Nuclear Information System (INIS)

Kertesz, Zs.; Szoboszlai, Z.; Dobos, E.; Borbely-Kiss, I.

2007-01-01

Complete text of publication follows. Size distribution is one of the basic properties of atmospheric aerosol. It is closely related to the origin, chemical composition and age of the aerosol particles, and it influences the optical properties, environmental effects and health impact of aerosol. As part of the ongoing aerosol research in the Group of Ion Beam Applications of the Atomki, elemental mass size distribution of urban aerosol were determined using particle induced X-ray emission (PIXE) analytical technique. Aerosol sampling campaigns were carried out with 9-stage PIXE International cascade impactors, which separates the aerosol into 10 size fractions in the 0.05-30 ?m range. Five 48-hours long samplings were done in the garden of the Atomki, in April and in October, 2007. Both campaigns included weekend and working day samplings. Basically two different kinds of particles could be identified according to the size distribution. In the size distribution of Al, Si, Ca, Fe, Ba, Ti, Mn and Co one dominant peak can be found around the 3 m aerodynamic diameter size range, as it is shown on Figure 1. These are the elements of predominantly natural origin. Elements like S, Cl, K, Zn, Pb and Br appears with high frequency in the 0.25-0.5 mm size range as presented in Figure 2. These elements are originated mainly from anthropogenic sources. However sometimes in the size distribution of these elements a 2 nd , smaller peak appears at the 2-4 μm size ranges, indicating different sources. Differences were found between the size distribution of the spring and autumn samples. In the case of elements of soil origin the size distribution was shifted towards smaller diameters during October, and a 2 nd peak appeared around 0.5 μm. A possible explanation to this phenomenon can be the different meteorological conditions. No differences were found between the weekend and working days in the size distribution, however the concentration values were smaller during the weekend

Design and Preparation of Cross-Linked Polystyrene Nanoparticles for Elastomer Reinforcement

Directory of Open Access Journals (Sweden)

Ming Lu

2010-01-01

Full Text Available Cross-linked polystyrene (PS particles in a latex form were synthesized by free radical emulsion polymerization. The nano-PS-filled elastomer composites were prepared by the energy-saving latex compounding method. Results showed that the PS particles took a spherical shape in the size of 40–60 nm with a narrow size distribution, and the glass-transition temperature of the PS nanoparticles increased with the cross-linking density. The outcomes from the mechanical properties demonstrated that when filled into styrene-butadiene rubber (SBR, nitrile-butadiene rubber (NBR, and natural rubber (NR, the cross-linked PS nano-particles exhibited excellent reinforcing capabilities in all the three matrices, and the best in the SBR matrix. In comparison with that of the carbon black filled composites, another distinguished advantage of the cross-linked PS particles filled elastomer composites was found to be light weight in density, which could help to save tremendous amount of energy when put into end products.

Eddington's demon: inferring galaxy mass functions and other distributions from uncertain data

Science.gov (United States)

Obreschkow, D.; Murray, S. G.; Robotham, A. S. G.; Westmeier, T.

2018-03-01

We present a general modified maximum likelihood (MML) method for inferring generative distribution functions from uncertain and biased data. The MML estimator is identical to, but easier and many orders of magnitude faster to compute than the solution of the exact Bayesian hierarchical modelling of all measurement errors. As a key application, this method can accurately recover the mass function (MF) of galaxies, while simultaneously dealing with observational uncertainties (Eddington bias), complex selection functions and unknown cosmic large-scale structure. The MML method is free of binning and natively accounts for small number statistics and non-detections. Its fast implementation in the R-package dftools is equally applicable to other objects, such as haloes, groups, and clusters, as well as observables other than mass. The formalism readily extends to multidimensional distribution functions, e.g. a Choloniewski function for the galaxy mass-angular momentum distribution, also handled by dftools. The code provides uncertainties and covariances for the fitted model parameters and approximate Bayesian evidences. We use numerous mock surveys to illustrate and test the MML method, as well as to emphasize the necessity of accounting for observational uncertainties in MFs of modern galaxy surveys.

Rheological Behavior of Entangled Polystyrene-Polyhedral Oligosilsesquioxane (POSS) Copolymer (Postprint)

National Research Council Canada - National Science Library

Wu, Jian; Mather, Patrick T; Haddad, Timothy S; Kim, Gyeong-Man

2006-01-01

...: random copolymers of polystyrene (PS) and styryl-based polyhedral oligosilsesquioxane (POSS), R7(Si8O12)(C6H4CH=CH2), with R = isobutyl (iBu). A series of styrene-styryl POSS random copolymers with 0, 6, 15, 30, 50 wt...

Synthesis of polystyrene coated SiC nanowires as fillers in a polyurethane matrix for electromechanical conversion

Energy Technology Data Exchange (ETDEWEB)

Rybak, Andrzej; Warde, Micheline; Bechelany, Mikhael; Brioude, Arnaud; Toury, Berangere; Cornu, David; Miele, Philippe [Laboratoire des Multimateriaux et Interfaces, UMR 5615 CNRS, Universite Lyon 1, Universite de Lyon, 43 Boulevard du 11 Novembre 1918, F-69622 Villeurbanne Cedex (France); Beyou, Emmanuel; Chaumont, Philippe [Ingenierie des Materiaux Polymeres, UMRCNRS 5223, Laboratoire des Materiaux Polymeres et des Biomateriaux, Universite Lyon 1, Universite de Lyon, 15 Boulevard Latarget, 69622 Villeurbanne Cedex (France); Guiffard, Benoit; Seveyrat, Laurence; Guyomar, Daniel, E-mail: beyou@univ-lyon1.fr, E-mail: David.Cornu@iemm.univ-montp2.fr [Laboratoire de Genie Electrique et Ferroelectricite, LGEF-INSA Lyon, Batiment Gustave Ferrie, 8 rue de la Physique, F-69621 Villeurbanne Cedex (France)

2010-04-09

Grafting of polystyrene (PS) from silica coating of silicon carbide nanowires (SiCNWs) has been performed by a two-step nitroxide mediated free radical polymerization (NMP) of styrene. First, an alkoxyamine based on N-tert-butyl-N-(1-diethylphosphono-2,2-dimethylpropyl) nitroxide (DEPN) was covalently attached onto NWs through free surface silanol groups. To immobilize the alkoxyamine initiator on the silica surface, alkoxylamine was formed in situ by the simultaneous reaction of polymerizable acryloxy propyl trimethoxysilane (APTMS), azobis isobutyronitrile (AIBN), and DEPN, which was used as a radical trap. Polystyrene chains with controlled molecular weights and narrow polydispersity were then grown from the alkoxyamine-functionalized NWs surface in the presence of a 'free' sacrificial styrylDEPN alkoxyamine. Both the initiator and polystyrene chains were characterized by FTIR and {sup 13}C solid-state NMR and quantified by TGA. Ensuing nanocomposites were characterized by FEG-SEM, TEM and Raman spectroscopy. EDX analysis performed on functionalized nanowires during FEG-SEM analysis also gave evidence of grafting by a strong increase in the average C/Si atomic ratio. Incorporation of 2 wt% NWs into the polyurethane (PU) matrix has been carried out to prepare homogeneous nanocomposite films. The electric field induced thickness strain response has been investigated for the polystyrene-grafted silica coated SiC NWs (PU-SiC-SiO{sub 2}-PS) nanocomposites and compared to pure polyurethane film and PU-SiC-SiO{sub 2} nanocomposite without polystyrene grafting. At a moderate electric field of 10 V {mu}m{sup -1}, SiC-SiO{sub 2}-PS loading increased the strain level of pure PU by a factor of 2.2. This improvement came partially due to polystyrene grafting since PU-SiC-SiO{sub 2} films showed only a 1.7 times increase. The observed higher strain response of these nanocomposites makes them very attractive for micro-electromechanical applications.

Circularly polarized luminescence of syndiotactic polystyrene

Science.gov (United States)

Rizzo, Paola; Abbate, Sergio; Longhi, Giovanna; Guerra, Gaetano

2017-11-01

Syndiotactic polystyrene (s-PS) films, when crystallized from the amorphous state by temporary sorption of non-racemic guest molecules (like carvone) not only exhibit unusually high optical activity, both in the UV-Visible and Infrared ranges, but also present circularly polarized luminescence (CPL) with high dissymmetry ratios (g = ΔI/I values in the range 0.02-0.03). Experimental evidences provide support, rather than to the usual molecular circular dichroism, to a supramolecular chiral optical response being extrinsic to the site of photon absorption and emission, possibly associated with a helical morphology of s-PS crystallites.

Synthesis of Well-Defined Three-Arm Star-Branched Polystyrene through Arm-First Coupling Approach by Atom Transfer Radical Polymerization

Directory of Open Access Journals (Sweden)

Syed Shahabuddin

2015-01-01

Full Text Available Here we describe a simple route to synthesize three-arm star-branched polystyrene. Atom transfer radical polymerization technique has been utilized to yield branched polystyrene involving Williamson coupling strategy. Initially a linear polymeric chain of predetermined molecular weight has been synthesized which is further end-functionalized into a primary alkyl bromide moiety, a prime requisition for Williamson reaction. The end-functionalized polymer is then coupled using 1,1,1-tris(4-hydroxyphenylethane, a trifunctional core molecule, to give well-defined triple-arm star-branched polystyrene.

Copolymer fingerprints of polystyrene-block-polyisoprene by MALDI-ToF-MS

NARCIS (Netherlands)

Willemse, R.X.E.; Staal, B.B.P.; Donkers, E.H.D.; Herk, van A.M.

2004-01-01

MALDI-ToF-MS mass spectra of copolymers contain a lot of information on both chain length distribution (CLD) and chemical composition distribution (CCD). In this paper an approach for extracting detailed information from a MALDI-ToF-MS mass spectrum is presented that enables the study of

Silica-Polystyrene Nanocomposite Particles Synthesized by Nitroxide-Mediated Polymerization and Their Encapsulation through Miniemulsion Polymerization

Directory of Open Access Journals (Sweden)

Bérangère Bailly

2006-01-01

Full Text Available Polystyrene (PS chains with molecular weights comprised between 8000 and 64000 g⋅mol-1 and narrow polydispersities were grown from the surface of silica nanoparticles (Aerosil A200 fumed silica and Stöber silica, resp. through nitroxide-mediated polymerization (NMP. Alkoxyamine initiators based on N-tert-butyl-1-diethylphosphono-2,2-dimethylpropyl nitroxide (DEPN and carrying a terminal functional group have been synthesized in situ and grafted to the silica surface. The resulting grafted alkoxyamines have been employed to initiate the growth of polystyrene chains from the inorganic surface. The maximum grafting density of the surface-tethered PS chains was estimated and seemed to be limited by initiator confinement at the interface. Then, the PS-grafted Stöber silica nanoparticles were entrapped inside latex particles via miniemulsion polymerization. Transmission electron microscopy indicated the successful formation of silica-polystyrene core-shell particles.

POTENTIAL USE OF GRAFT COPOLYMERS OF MERCERIZED FLAX AS FILLER IN POLYSTYRENE COMPOSITE MATERIALS

Directory of Open Access Journals (Sweden)

Susheel Kalia

2008-11-01

Full Text Available Graft copolymerization of binary vinyl monomers onto mercerized flax fiber was carried out for the enhancement of mechanical properties of polystyrene composites. Binary vinyl monomer mixture of AA+AN has been found to show maximum grafting (33.55% onto mercerized flax. Graft copolymers thus synthesized were characterized with FT-IR spectroscopy, SEM, and TGA techniques. Mercerized flax (MF showed maximum thermal stability in comparison to graft copolymers. It has been found that polystyrene composites reinforced with graft copolymers showed improvement in mechanical properties such as wear resistance, compressive strength, and tensile strength.

Plasticization effect of C60 on the fast dynamics of polystyrene and related polymers: an incoherent neutron scattering study

International Nuclear Information System (INIS)

Sanz, Alejandro; Ruppel, Markus; Cabral, Joao T; Douglas, Jack F

2008-01-01

We utilize inelastic incoherent neutron scattering (INS) to quantify how fullerenes affect the 'fast' molecular dynamics of a family of polystyrene related macromolecules. In particular, we prepared bulk nanocomposites of (hydrogenous and ring-deuterated) polystyrene and poly(4-methyl styrene) using a rapid precipitation method where the C 60 relative mass fraction ranged from 0% to 4%. Elastic window scan measurements, using a high resolution (0.9 μeV) backscattering spectrometer, are reported over a wide temperature range (2-450 K). Apparent Debye-Waller (DW) factors 2 >, characterizing the mean-square amplitude of proton displacements, are determined as a function of temperature, T. We find that the addition of C 60 to these polymers leads to a progressive increase in 2 > relative to the pure polymer value over the entire temperature range investigated, where the effect is larger for larger nanoparticle concentration. This general trend seems to indicate that the C 60 nanoparticles plasticize the fast (∼10 -15 s) local (∼1 A) dynamics of these polymer glasses. Generally, we expect nanoparticle additives to affect polymer dynamics in a similar fashion to thin films in the sense that the high interfacial area may cause both a speeding up and slowing down of the glass state dynamics depending on the polymer-surface interaction

The link between the baryonic mass distribution and the rotation curve shape

Science.gov (United States)

Swaters, R. A.; Sancisi, R.; van der Hulst, J. M.; van Albada, T. S.

2012-09-01

The observed rotation curves of disc galaxies, ranging from late-type dwarf galaxies to early-type spirals, can be fitted remarkably well simply by scaling up the contributions of the stellar and H I discs. This 'baryonic scaling model' can explain the full breadth of observed rotation curves with only two free parameters. For a small fraction of galaxies, in particular early-type spiral galaxies, H I scaling appears to fail in the outer parts, possibly due to observational effects or ionization of H I. The overall success of the baryonic scaling model suggests that the well-known global coupling between the baryonic mass of a galaxy and its rotation velocity (known as the baryonic Tully-Fisher relation) applies at a more local level as well, and it seems to imply a link between the baryonic mass distribution and the distribution of total mass (including dark matter).

Mass resolved angular distribution of fission products in 20Ne + 232Th reaction

International Nuclear Information System (INIS)

Tripathi, R.; Sodaye, S.; Sudarshan, K.; Kumar, Amit; Guin, R.

2011-01-01

Mass resolved angular distribution of fission products was measured in 20 Ne + 232 Th reaction at beam energy of 120 MeV. A preliminary analysis of the angular distribution data of fission products shows higher average anisotropy compared to that calculated using statistical theory. A signature of rise in anisotropy near symmetry, as reported in earlier studies in literature, is also seen. Further study is in progress to get more detailed information about the contribution from non-compound nucleus fission and dependence of angular anisotropy on asymmetry of mass division

The effect of nuclear gas distribution on the mass determination of supermassive black holes

Science.gov (United States)

Mejía-Restrepo, J. E.; Lira, P.; Netzer, H.; Trakhtenbrot, B.; Capellupo, D. M.

2018-01-01

Supermassive black holes reside in the nuclei of most galaxies. During their active episodes, black holes are powered by accretion discs where gravitational energy is converted into radiation1. Accurately determining black hole masses is key to understand how the population evolves over time and how the black holes relate to their host galaxies2-4. Beyond the local universe, z ≳ 0.2, the mass is commonly estimated assuming a virialized motion of gas in the close vicinity of the active black holes, traced through broad emission lines5,6. However, this procedure has uncertainties associated with the unknown distribution of the gas clouds. Here, we show that the black hole masses derived from the properties of the accretion disk and virial mass estimates differ by a factor that is inversely proportional to the width of the broad emission lines. This leads to virial mass misestimations up to a factor of six. Our results suggest that a planar gas distribution that is inclined with respect to the line of sight may account for this effect. However, radiation pressure effects on the distribution of gas can also reproduce our results. Regardless of the physical origin, our findings contribute to mitigating the uncertainties in current black hole mass estimations and, in turn, will help us to better understand the evolution of distant supermassive black holes and their host galaxies.

Does mass azithromycin distribution impact child growth and nutrition in Niger? A cluster-randomized trial.

Directory of Open Access Journals (Sweden)

Abdou Amza

2014-09-01

Full Text Available Antibiotic use on animals demonstrates improved growth regardless of whether or not there is clinical evidence of infectious disease. Antibiotics used for trachoma control may play an unintended benefit of improving child growth.In this sub-study of a larger randomized controlled trial, we assess anthropometry of pre-school children in a community-randomized trial of mass oral azithromycin distributions for trachoma in Niger. We measured height, weight, and mid-upper arm circumference (MUAC in 12 communities randomized to receive annual mass azithromycin treatment of everyone versus 12 communities randomized to receive biannual mass azithromycin treatments for children, 3 years after the initial mass treatment. We collected measurements in 1,034 children aged 6-60 months of age.We found no difference in the prevalence of wasting among children in the 12 annually treated communities that received three mass azithromycin distributions compared to the 12 biannually treated communities that received six mass azithromycin distributions (odds ratio = 0.88, 95% confidence interval = 0.53 to 1.49.We were unable to demonstrate a statistically significant difference in stunting, underweight, and low MUAC of pre-school children in communities randomized to annual mass azithromycin treatment or biannual mass azithromycin treatment. The role of antibiotics on child growth and nutrition remains unclear, but larger studies and longitudinal trials may help determine any association.

An immunoassay for dibutyl phthalate based on direct hapten linkage to the polystyrene surface of microtiter plates.

Directory of Open Access Journals (Sweden)

Chenxi Wei

Full Text Available BACKGROUND: Dibutyl phthalate (DBP is predominantly used as a plasticizer inplastics to make them flexible. Extensive use of phthalates in both industrial processes and other consumer products has resulted in the ubiquitous presence of phthalates in the environment. In order to better determine the level of pollution in the environment and evaluate the potential adverse effects of exposure to DBP, immunoassay for DBP was developed. METHODOLOGY/PRINCIPAL FINDINGS: A monoclonal antibody specific to DBP was produced from a stable hybridoma cell line generated by lymphocyte hybridoma technique. An indirect competitive enzyme-linked immunosorbent assay (icELISA employing direct coating of hapten on polystyrene microtiter plates was established for the detection of DBP. Polystyrene surface was first oxidized by permanganate in dilute sulfuric acid to generate carboxyl groups. Then dibutyl 4-aminophthalate, which is an analogue of DBP, was covalently linked to the carboxyl groups of polystyrene surface with 1-ethyl-3-(3-dimethylaminopropyl carbodiimide hydrochloride (EDC. Compared with conjugate coated format (IC(50=106 ng/mL, the direct hapten coated format (IC(50=14.6 ng/mL improved assay sensitivity after careful optimization of assay conditions. The average recovery of DBP from spiked water sample was 104.4% and the average coefficient of variation was 9.95%. Good agreement of the results obtained by the hapten coated icELISA and gas chromatography-mass spectrometry further confirmed the reliability and accuracy of the icELISA for the detection of DBP in certain plastic and cosmetic samples. CONCLUSIONS/SIGNIFICANCE: The stable and efficient hybridoma cell line obtained is an unlimited source of sensitive and specific antibody to DBP. The hapten coated format is proposed as generally applicable because the carboxyl groups on modified microtiter plate surface enables stable immobilization of aminated or hydroxylated hapten with EDC. The developed

Effects of fracture distribution and length scale on the equivalent continuum elastic compliance of fractured rock masses

Directory of Open Access Journals (Sweden)

Marte Gutierrez

2015-12-01

Full Text Available Fracture systems have strong influence on the overall mechanical behavior of fractured rock masses due to their relatively lower stiffness and shear strength than those of the rock matrix. Understanding the effects of fracture geometrical distribution, such as length, spacing, persistence and orientation, is important for quantifying the mechanical behavior of fractured rock masses. The relation between fracture geometry and the mechanical characteristics of the fractured rock mass is complicated due to the fact that the fracture geometry and mechanical behaviors of fractured rock mass are strongly dependent on the length scale. In this paper, a comprehensive study was conducted to determine the effects of fracture distribution on the equivalent continuum elastic compliance of fractured rock masses over a wide range of fracture lengths. To account for the stochastic nature of fracture distributions, three different simulation techniques involving Oda's elastic compliance tensor, Monte Carlo simulation (MCS, and suitable probability density functions (PDFs were employed to represent the elastic compliance of fractured rock masses. To yield geologically realistic results, parameters for defining fracture distributions were obtained from different geological fields. The influence of the key fracture parameters and their relations to the overall elastic behavior of the fractured rock mass were studied and discussed. A detailed study was also carried out to investigate the validity of the use of a representative element volume (REV in the equivalent continuum representation of fractured rock masses. A criterion was also proposed to determine the appropriate REV given the fracture distribution of the rock mass.

Two-Dimensional Liquid Chromatography Analysis of Polystyrene/Polybutadiene Block Copolymers.

Science.gov (United States)

Lee, Sanghoon; Choi, Heejae; Chang, Taihyun; Staal, Bastiaan

2018-05-15

A detailed characterization of a commercial polystyrene/polybutadiene block copolymer material (Styrolux) was carried out using two-dimensional liquid chromatography (2D-LC). The Styrolux is prepared by statistical linking reaction of two different polystyrene- block-polybutadienyl anion precursors with a multivalent linking agent. Therefore, it is a mixture of a number of branched block copolymers different in molecular weight, composition, and chain architecture. While individual LC analysis, including size exclusion chromatography, interaction chromatography, or liquid chromatography at critical condition, is not good enough to resolve all the polymer species, 2D-LC separations coupling two chromatography methods were able to resolve all polymer species present in the sample; at least 13 block copolymer species and a homopolystyrene blended. Four different 2D-LC analyses combining a different pair of two LC methods provide their characteristic separation results. The separation characteristics of the 2D-LC separations are compared to elucidate the elution characteristics of the block copolymer species.

Sorption behaviour of polystyrene grafted sago starch in various solvents

International Nuclear Information System (INIS)

Janarthanan, P.; Yunus, W.M.Z.W.; Ahmed, M.B.; Rahman, M.Z.; Haron, M.J.; Silong, S.

2001-01-01

This paper describes swelling properties of polystyrene grafted sago starch in dimethyl sulfoxide (DMSO); chloroform (CHCl/sub 3/), water, acetone carbon tetrachloride (CCl/sub 4/) cyclohexanone and toluene. The copolymer for this study was prepared by grafting styrene onto sago starch using ceric ammonium nitrate as a redox initiator. Solvent uptake of the copolymer with respect to time was obtained by soaking the samples in chosen solvents for various time intervals at 25+-1 degree centigrade. The results obtained from swelling of polystyrene grafted sago starch in polar and non polar solvents showed that the percentage of swelling at equilibrium and the swelling rate coefficient decreased in the following order: DMSO > water > acetone cyclohexanone approx. CHCl/sub 3/ > toluene approx. CCl/sub 4/. Dimethyl sulfoxide showed the highest percentage of swelling at equilibrium that is 765%. Diffusions of the solvents onto the polymers were found to be of a Fickian only for DMSO. (author)

Measurement of mass distribution of U-235 fission products in the intermediate neutron region

International Nuclear Information System (INIS)

Nakagomi, Yoshihiro; Kobayashi, Shohei; Yamamoto, Shuji; Kanno, Ikuo; Wakabayashi, Hiroaki.

1982-01-01

The mass distribution and the momentum distribution of U-235 fission products in the intermediate neutron region were measured by using a combination system of the Yayoi intermediate neutron column and an electron linear accelerator. The double energy measurement method was applied. A fission chamber, which consists of an enriched uranium target and two Si surface barrier detectors, was used for the measurement of the neutrons with energy above 1.3 eV. The linear accelerator was operated at the repetition rate of 100 Hz and the pulse width of 10 ns. The data obtained by the two-dimensional pulse height analysis were analyzed by the Schmitt's method. The preliminary results of the mass distribution and the momentum distribution of fission fragments were obtained. (Kato, T.)

Low-cost silver capped polystyrene nanotube arrays as super-hydrophobic substrates for SERS applications.

Science.gov (United States)

Lovera, Pierre; Creedon, Niamh; Alatawi, Hanan; Mitchell, Micki; Burke, Micheal; Quinn, Aidan J; O'Riordan, Alan

2014-05-02

In this paper, we describe the fabrication, simulation and characterization of dense arrays of freestanding silver capped polystyrene nanotubes, and demonstrate their suitability for surface enhanced Raman scattering (SERS) applications. Substrates are fabricated in a rapid, low-cost and scalable way by melt wetting of polystyrene (PS) in an anodized alumina (AAO) template, followed by silver evaporation. Scanning electron microscopy reveals that substrates are composed of a dense array of freestanding polystyrene nanotubes topped by silver nanocaps. SERS characterization of the substrates, employing a monolayer of 4-aminothiophenol (4-ABT) as a model molecule, exhibits an enhancement factor of ∼1.6 × 10(6), in agreement with 3D finite difference time domain simulations. Contact angle measurements of the substrates revealed super-hydrophobic properties, allowing pre-concentration of target analyte into a small volume. These super-hydrophobic properties of the samples are taken advantage of for sensitive detection of the organic pollutant crystal violet, with detection down to ∼400 ppt in a 2 μl aliquot demonstrated.

Low-cost silver capped polystyrene nanotube arrays as super-hydrophobic substrates for SERS applications

International Nuclear Information System (INIS)

Lovera, Pierre; Creedon, Niamh; Alatawi, Hanan; Mitchell, Micki; Burke, Micheal; Quinn, Aidan J; O’Riordan, Alan

2014-01-01

In this paper, we describe the fabrication, simulation and characterization of dense arrays of freestanding silver capped polystyrene nanotubes, and demonstrate their suitability for surface enhanced Raman scattering (SERS) applications. Substrates are fabricated in a rapid, low-cost and scalable way by melt wetting of polystyrene (PS) in an anodized alumina (AAO) template, followed by silver evaporation. Scanning electron microscopy reveals that substrates are composed of a dense array of freestanding polystyrene nanotubes topped by silver nanocaps. SERS characterization of the substrates, employing a monolayer of 4-aminothiophenol (4-ABT) as a model molecule, exhibits an enhancement factor of ∼1.6 × 10 6 , in agreement with 3D finite difference time domain simulations. Contact angle measurements of the substrates revealed super-hydrophobic properties, allowing pre-concentration of target analyte into a small volume. These super-hydrophobic properties of the samples are taken advantage of for sensitive detection of the organic pollutant crystal violet, with detection down to ∼400 ppt in a 2 μl aliquot demonstrated. (paper)

The distribution of mass in the planetary system and solar nebulae

International Nuclear Information System (INIS)

Weidenschilling, S.J.

1977-01-01

A model 'solar nebula' is constructed by adding the solar complement of light elements to each planet, using recent models of planetary compositions. Uncertainties in this approach are estimated. The computed surface density varies approximately as rsup(-3/2). Mercury, Mars and the asteroid belt are anomalously low in mass, but processes exist which would preferentially remove matter from these regions. Planetary masses and compositions are generally consistent with a monotonic density distribution in the primordial solar nebula. (Auth.)

Application of methods of mathematical modeling for determining of radiation-protective characteristics of polystyrene-metal composite materials

International Nuclear Information System (INIS)

Klepikov, V.F.; Prokhorenko, E.M.; Lytvynenko, V.V.; Zakharchenko, A.A.; Nazhmuradov, M.A.

2016-01-01

Radiation safety features of polystyrene steel composite materials were found by means of mathematical modeling techniques. We determined the attenuation of the gamma quantum flux passing through a solid protective layer compared with those attenuation for the bulk protective layer. Change of fractional attenuation of the dose absorbed by 10 and 50 mm thick composites is calculated. Dependence between protective properties of composite and its blend composition was studied. Modifications of technical process of composite materials production were performed. Rotation speed of agitator system was found. It was defined that heating time of polystyrene steel mix is longer than heating time of polystyrene tungstic one. Degree of mix heating and integrity of thermic field on its surface was controlled with the help of IR radiometry methods.

Ionoluminescence properties of polystyrene-hosted fluorophore films induced by helium ions of energy 50-350 keV

Science.gov (United States)

Chakraborty, Subha; Huang, Mengbing

2017-10-01

We report on measurements and analysis of ionoluminescence properties of pure polystyrene films and polystyrene films doped with four types of fluorophores in low kinetic energies (50-350 keV) of ion irradiation. We have developed a theoretical model to understand the experimentally observed ionoluminescence behaviors in terms of scintillation yield from individual ion tracks, photophysical energy transfer mechanisms, and irradiation-induced defects. A comparison of the model and experimental results suggests that singlet up-conversion resulting from triplet-triplet annihilation processes may be responsible for enhanced singlet emission of the fluorophores at high ion beam flux densities. Energy transfer from the polystyrene matrix to the fluorophore molecules has been identified as an effective pathway to increasing the fluorescence efficiency in the doped scintillator films.

Uniform formation of Au coated polystyrene core-shell structure using metallization process

Energy Technology Data Exchange (ETDEWEB)

Kim, Kyoungseob; Koo, Jonghyun; Roh, Yonghan, E-mail: yhroh@skku.edu

2011-08-01

There are several methods for the fabrication of core-shell particles, including chemical reduction and self-assembly. In this study, the chemical reduction method was used to fabricate 100 nm, Au-coated polystyrene nanoparticles. The formation of the gold layer was based on the increase of gold coverage by the reaction with aniline and HAuCl{sub 4}. This method allowed for efficient control of the gold coverage and led to relatively stable products. The formation of Au clusters on the surface of the 100 nm polystyrene beads was characterized by scanning electron microscope and high resolution tunneling electron microscope. As a result, the Au-coated nanoparticles can be used in various applications such as surface plasmon resonators, drug delivery systems and electronic optical devices.

Synthesis and characterization of magnetic and non-magnetic core-shell polyepoxide micrometer-sized particles of narrow size distribution.

Science.gov (United States)

Omer-Mizrahi, Melany; Margel, Shlomo

2009-01-15

Core polystyrene microspheres of narrow size distribution were prepared by dispersion polymerization of styrene in a mixture of ethanol and 2-methoxy ethanol. Uniform polyglycidyl methacrylate/polystyrene core-shell micrometer-sized particles were prepared by emulsion polymerization at 73 degrees C of glycidyl methacrylate in the presence of the core polystyrene microspheres. Core-shell particles with different properties (size, surface morphology and composition) have been prepared by changing various parameters belonging to the above seeded emulsion polymerization process, e.g., volumes of the monomer glycidyl methacrylate and the crosslinker monomer ethylene glycol dimethacrylate. Magnetic Fe(3)O(4)/polyglycidyl methacrylate/polystyrene micrometer-sized particles were prepared by coating the former core-shell particles with magnetite nanoparticles via a nucleation and growth mechanism. Characterization of the various particles has been accomplished by routine methods such as light microscopy, SEM, FTIR, BET and magnetic measurements.

Impact of fat mass distribution body shapes on muscles strength and the joints pain

Directory of Open Access Journals (Sweden)

Zerf Mohammed

2016-01-01

Full Text Available Our study focuses on fat mass distribution body shapes type as measured to determine their effect on skeletal muscle strengthening lumbar extensors (upper and lower limbs where our background confirms that every girl has a natural body type of rectangle, apple, pear, or hourglass. It is good for her to know which type of body shape she is, so she can learn what exercises to do, whereas similar studies suggest that it is much better to challenge weight problems with exercise and dietary measures before resorting to figure shaping. For this purpose, our study was carried out with a total of thirty students, females listed in the Institute of Physical Education and Sport, University of Mostaganem, aged between 20 and 23 years; their homogeneity was based on age, sex, and academic specialty, classified based on the body mass index (BMI into two groups (normal and overweight and based on their body shape′s type into three groups (9 pear shape, 10 rectangle shape, and 11 hourglass shape as a protocol experimental to examine the impact of fat mass distribution body shapes type on lumbar extensor strength. Based on our data analysis, we confirm that the pear and the rectangle shape affect the strength lumbar extensors due to body weight distribution which increases the risks relating to the skeletal muscles. Weight gain is a factor contributing to the weakness of skeletal muscles. However, the body shape explains the anomalies of the distribution of fat mass and BMI risk observed in our sample in the lower and upper part of the body recorded by the values of Killy test and endurance of trunk, the case of the pear and the rectangle shape back pain, which are consisting in excess of the body fat distributed in comparison with less percentage of muscle mass. Whereas this difference can affect the pelvic position.

Measurement of particle size distribution and mass concentration of nuclear fuel aerosols

International Nuclear Information System (INIS)

Pickering, S.

1982-01-01

The particle size distribution and particle mass concentration of a nuclear fuel aerosol is measured by admitting the aerosol into a vertically-extending container, positioning an alpha particle detector within the container so that its window is horizontal and directed vertically, stopping the admission of aerosol into the container, detecting the alpha-activity of the particles of the aerosol sedimenting onto the detector window (for example in a series of equal time intervals until a constant level is reached), and converting the alpha-activity measurements into particle size distribution and/or particle mass concentration measurements. The detector is attached to a pivotted arm and by raising a counterweight can be lowered from the container for cleaning. (author)

Effects of Habitual Physical Activity and Fitness on Tibial Cortical Bone Mass, Structure and Mass Distribution in Pre-pubertal Boys and Girls: The Look Study.

Science.gov (United States)

Duckham, Rachel L; Rantalainen, Timo; Ducher, Gaele; Hill, Briony; Telford, Richard D; Telford, Rohan M; Daly, Robin M

2016-07-01

Targeted weight-bearing activities during the pre-pubertal years can improve cortical bone mass, structure and distribution, but less is known about the influence of habitual physical activity (PA) and fitness. This study examined the effects of contrasting habitual PA and fitness levels on cortical bone density, geometry and mass distribution in pre-pubertal children. Boys (n = 241) and girls (n = 245) aged 7-9 years had a pQCT scan to measure tibial mid-shaft total, cortical and medullary area, cortical thickness, density, polar strength strain index (SSIpolar) and the mass/density distribution through the bone cortex (radial distribution divided into endo-, mid- and pericortical regions) and around the centre of mass (polar distribution). Four contrasting PA and fitness groups (inactive-unfit, inactive-fit, active-unfit, active-fit) were generated based on daily step counts (pedometer, 7-days) and fitness levels (20-m shuttle test and vertical jump) for boys and girls separately. Active-fit boys had 7.3-7.7 % greater cortical area and thickness compared to inactive-unfit boys (P girls, but active-fit girls had 6.1 % (P girls, which was likely due to their 6.7 % (P active-fit girls. Higher levels of habitual PA-fitness were associated with small regional-specific gains in 66 % tibial cortical bone mass in pre-pubertal children, particularly boys.

Impact of Mass and Weight Distribution on Manual Wheelchair Propulsion Torque.

Science.gov (United States)

Sprigle, Stephen; Huang, Morris

2015-01-01

Propulsion effort of manual wheelchairs, a major determinant of user mobility, is a function of human biomechanics and mechanical design. Human studies that investigate both variables simultaneously have resulted in largely inconsistent outcomes, motivating the implementation of a robotic propulsion system that characterizes the inherent mechanical performance of wheelchairs. This study investigates the impacts of mass and mass distribution on manual wheelchair propulsion by configuring an ultra-lightweight chair to two weights (12-kg and 17.6-kg) and two load distributions (70% and 55% on drive wheels). The propulsion torques of these four configurations were measured for a straight maneuver and a fixed-wheel turn, on both tile and carpet. Results indicated that increasing mass to 17.6-kg had the largest effect on straight acceleration, requiring 7.4% and 5.8% more torque on tile and carpet, respectively. Reducing the drive wheel load to 55% had the largest effect on steady-state straight motion and on both turning acceleration and steady-state turning; for tile and carpet, propulsion torque increased by 13.5% and 11.8%, 16.5% and 4.1%, 73% and 5.1%, respectively. These results demonstrate the robot's high sensitivity, and support the clinical importance of evaluating effects of wheelchair mass and axle position on propulsion effort across maneuvers and surfaces.

Nano Petri dishes: a new polystyrene platform for studying cell-nanoengineered surface interactions

International Nuclear Information System (INIS)

Cha, Kyoung Je; Na, Moon-Hee; Kim, Hyung Woo; Kim, Dong Sung

2014-01-01

In this study, we fabricated and fully characterized a new type of polystyrene (PS) cell-culture platform containing nanoengineered surfaces (NES), referred to as a nano Petri dish, which can be used at the transition stage of basic cell–NES interaction studies for clinical applications. Nano-injection molding in this study was used for the mass production of the nano Petri dish having nanopore arrays. The effects of processing parameters of the injection molding on the replication quality of the nanopore arrays were quantitatively evaluated by means of design of experiments based on the Taguchi method. This allowed efficient and reliable cell culture studies by providing large numbers of the same dishes, in addition to removing the fixation step of the NES plates inside the cell-culture container. Physical, chemical and mechanical properties of the NES, as well as cell behavior including attachment and proliferation of human osteosarcoma MG-63 cells on the NES, were then characterized, with and without the oxygen plasma surface treatment. (paper)

Nano Petri dishes: a new polystyrene platform for studying cell-nanoengineered surface interactions

Science.gov (United States)

Cha, Kyoung Je; Na, Moon-Hee; Kim, Hyung Woo; Kim, Dong Sung

2014-05-01

In this study, we fabricated and fully characterized a new type of polystyrene (PS) cell-culture platform containing nanoengineered surfaces (NES), referred to as a nano Petri dish, which can be used at the transition stage of basic cell-NES interaction studies for clinical applications. Nano-injection molding in this study was used for the mass production of the nano Petri dish having nanopore arrays. The effects of processing parameters of the injection molding on the replication quality of the nanopore arrays were quantitatively evaluated by means of design of experiments based on the Taguchi method. This allowed efficient and reliable cell culture studies by providing large numbers of the same dishes, in addition to removing the fixation step of the NES plates inside the cell-culture container. Physical, chemical and mechanical properties of the NES, as well as cell behavior including attachment and proliferation of human osteosarcoma MG-63 cells on the NES, were then characterized, with and without the oxygen plasma surface treatment.

Binary star statistics: the mass ratio distribution for very wide systems

International Nuclear Information System (INIS)

Trimble, V.

1987-01-01

The distribution of mass ratios for a sample of common proper motion (CPM) binaries is determined and compared with that of 798 visual binaries (VB's) studied earlier, in hopes of answering the question: Can the member stars of these systems have been drawn at random from the normal initial mass function for single stars? The observed distributions peak strongly toward q = 1.0 for both kinds of systems, but less strongly for the CPM's than for the VB's. Due allowance having been made for assorted observational selection effects, it seems quite probable that the CPM's represent the observed part of a population drawn at random from the normal IMF, while the VB's are much more difficult to interpret that way and could, perhaps, result from a formation mechanism that somewhat favors sytems with roughly equal components. (author)

3D-HST + CANDELS: the Evolution of the Galaxy Size-mass Distribution Since Z=3

Science.gov (United States)

VanDerWel, A.; Franx, M.; vanDokkum, P. G.; Skelton, R. E.; Momcheva, I. G.; Whitaker, K. E.; Brammer, G. B.; Bell, E. F.; Rix, H.-W.; Wuyts, S.;

Integrated lenses in polystyrene microfluidic devices

KAUST Repository

Fan, Yiqiang

2013-04-01

This paper reports a new method for integrating microlenses into microfluidic devices for improved observation. Two demonstration microfluidic devices were provided which were fabricated using this new technique. The integrated microlenses were fabricated using a free-surface thermo-compression molding method on a polystyrene (PS) sheet which was then bonded on top of microfluidic channels as a cover plate, with the convex microlenses providing a magnified image of the channel for the easier observation of the flow in the microchannels. This approach for fabricating the integrated microlens in microfluidic devices is rapid, low cost and without the requirement of cleanroom facilities. © 2013 IEEE.

Synthesis and properties of deuterated polystyrene

International Nuclear Information System (INIS)

Liu Chang; Jin Rong; Xu Yewei; Zhang Lin; Yan Hongwei; Du Kai; Wei Chengfu

2012-01-01

Deuterated poly(vinylcyclohexane) (D-PVCH, C 8 H 8 D 6 ) was successfully prepared via deuterated catalytic technology of polystyrene (PS). The structure of D-PVCH was characterized by FT-IR and 1 HNMR spectroscopy, and the results show good agreement with the proposed structure and the deuterated ratio is 41.5%. DSC and TG analyses of the D-PVCH show that D-PVCH possesses good thermal stability (glass transition temperature of 125 ℃, 5% weight loss temperature of 403 ℃). Additionally, D-PVCH dissolves in common solvents such as petroleum ether, cyclohexane and toluene at room temperature. Compared with PS, D-PVCH possesses better thermal stability and improved solubility. (authors)

The influence of some factors on the electrical conductivity and particle size of core/shell polystyrene/polyaniline composites

Directory of Open Access Journals (Sweden)

GORDANA D. NESTOROVIC

2005-11-01

Full Text Available The electrically conductive, micron-sized, core/shell polystyrene (PS/polyaniline (PANI composite particles were synthesized by chemical oxidative polymerization of aniline in the presence of micron-sized PS particles in 1 M HCl. The conditions of the dispersion polymerization of styrene were optimized. The influence of the initiator type employed for the chemical oxidative polymerization of aniline and the aniline (ANI concentration on the PS/PANI particle size and size distribution and their conductivity was investigated. The obtained results show that the conductivity of the samples increased with increasing ANI concentration. The conductivity of the PS/PANI composite particles obtained with the highest ANI concentration was of the same order of magnitude as that for PANI powder. The particle size did not depend on the concentration of ANI, while the particle size distribution was narrower at higher concentrations of ANI.

Evaluation of the environmental performance of alternatives for polystyrene production in Brazil.

Science.gov (United States)

Hansen, Adriana Petrella; da Silva, Gil Anderi; Kulay, Luiz

2015-11-01

The global demand for polystyrene is supposed to reach an overall baseline of 23.5 million tons by 2020. The market has experienced the effects of such growth, especially regarding the environmental performance of the production processes. In Brazil, renewable assets have been used to overcome the adverse consequences of this expansion. This study evaluates this issue for the production of Brazilian polystyrene resins, general-purpose polystyrene (GPPS) and high-impact polystyrene (HIPS). The effects of replacing fossil ethylene with a biobased alternative are also investigated. Life Cycle Assessment is applied for ten scenarios, with different technological approaches for renewable ethylene production and an alternative for obtaining bioethanol, which considers the export of electricity. The fossil GPPS and HIPS show a better performance than the partially renewable sources in terms of Climate Change (CC), Terrestrial Acidification (TA), Photochemical Oxidant Formation (POF), and Water Depletion (WD). The exception is Fossil Depletion (FD), a somewhat predictable result. The main environmental loads associated with the renewable options are related to the sugarcane production. Polybutadiene fails to provide greater additional impact to HIPS when compared to GPPS. With regard to obtaining ethylene from ethanol, Adiabatic Dehydration (AD) technology consumes less sugarcane than Adiabatic Dehydration at High Pressure (ADHP), which leads to gains in TA and POF. In contrast, ADHP was more eco-friendly for WD because of its lower water losses and in terms of CC because of the advantageous balance of fossil CO2(eq) at the agricultural stage and the lower consumption of natural gas in ethylene production. The electricity export is an auspicious environmental opportunity because it can counterbalance some of the negative impacts associated with the renewable route. According to a "cradle-to-grave" perspective, the partially renewable resins show a more favorable balance of

Extensional Rheology of Entangled Polystyrene Solutions Suggests Importance of Nematic Interactions

DEFF Research Database (Denmark)

Huang, Qian; Javier Alvarez, Nicolas; Matsumiya, Yumi

2013-01-01

We compare the linear and nonlinear rheological response of three entangled polystyrene solutions with the same concentration of polymer, but diluted using different solvents. The three solutions have exactly the same physical tube model parameters when normalized to the same time scale. Although...

Single-Step Nanoporation of Water-Immersed Polystyrene Film by Gaseous Nanobubbles

Czech Academy of Sciences Publication Activity Database

Tarábková, Hana; Janda, Pavel

2016-01-01

Roč. 32, č. 43 (2016), s. 11221-11229 ISSN 0743-7463 R&D Projects: GA ČR(CZ) GAP208/12/2429 Institutional support: RVO:61388955 Keywords : Atomic force microscopy * Biocompatibility * Polystyrenes Subject RIV: CG - Electrochemistry Impact factor: 3.833, year: 2016

Electrokinetic properties and conductance relaxation of polystyrene and silver iodide plugs

NARCIS (Netherlands)

Hoven, van den J.J.

1984-01-01

This thesis describes an experimental study on the electrokinetic and electrical properties of concentrated polystyrene and silver iodide dispersions. The purpose of the study is to obtain information on the structure of the electrical double layer at the solid-liquid interface. Special

Ferroferric oxide/polystyrene (Fe3O4/PS superparamagnetic nanocomposite via facile in situ bulk radical polymerization

Directory of Open Access Journals (Sweden)

2010-03-01

Full Text Available Organo-modified ferroferric oxide superparamagnetic nanoparticles, synthesized by the coprecipitation of superparamagnetic nanoparticles in presence of oleic acid (OA, were incorporated in polystyrene (PS by the facile in situ bulk radical polymerization by using 2,2-azobisisobutyronitrile (AIBN as initiator. The transmission electron microscopy (TEM analysis of the resultant uniform ferroferric oxide/polystyrene superparamagnetic nanocomposite (Fe3O4/PS showed that the superparamagnetic nanoparticles had been dispersed homogeneously in the polymer matrix due to the surface grafted polystyrene, confirmed by Fourier transform infrared (FT-IR spectroscopy and thermogravimetric analysis (TGA. The superparamagnetic property of the Fe3O4/PS nanocomposite was testified by the vibrating sample magnetometer (VSM analysis. The strategy developed is expected to be applied for the large-scale industrial manufacturing of the superparamagnetic polymer nanocomposite.

Extended x-ray absorption fine structure: Studies of zinc-neutralized sulfonated polystyrene ionomers

International Nuclear Information System (INIS)

Ding, Y.S.; Yarusso, D.J.; Pan, H.K.D.; Cooper, S.L.

1984-01-01

Extended x-ray absorption fine structure (EXAFS) measurements were performed on a series of zinc-neutralized sulfonated polystyrene ionomers and the local structure around the zinc atom was determined. An interference effect in the EXAFS signal between sulfur and oxygen atoms was found to be significant in these materials. A model for the local structure in the zinc-neutralized sulfonated polystyrene ionomers is proposed which suggests a highly ordered tetrahedral coordination of oxygen around the zinc atoms at a distance of 1.97 +- 0.02 A. In addition there are four sulfur atoms and four oxygen atoms at a distance of 3.15 +- 0.05 A. No zinc-zinc coordination within 5 A was detected in this study

Nanocomposite of polystyrene foil grafted with metallaboranes for antimicrobial activity

Czech Academy of Sciences Publication Activity Database

Benkocká, M.; Kolářová, K.; Matoušek, J.; Semerádtová, A.; Šícha, Václav; Kolská, Z.

2018-01-01

Roč. 441, MAY (2018), s. 120-129 ISSN 0169-4332 R&D Projects: GA MŠk(CZ) LM2015073 Institutional support: RVO:61388980 Keywords : Antimicrobial activity * Chemical grafting * Metallaboranes * Piranha solution * Polystyrene * Surface properties Subject RIV: CA - Inorganic Chemistry OBOR OECD: Inorganic and nuclear chemistry Impact factor: 3.387, year: 2016

Spectroscopic study of the charge-transfer complexes TiCl4/styrene and TiCl4/polystyrene

Science.gov (United States)

Gonçalves, Norberto S.; Noda, Lúcia. K.

2017-10-01

In this work, solutions of TiCl4/styrene and TiCl4/polystyrene charge-transfer complexes in CHCl3 or CDCl3 were investigated by UV-vis, resonance Raman and 1H NMR spectroscopies in order to study their molecular and electronic structures. Both show a yellow colour due to absorption in the 400 nm region, related to a charge-transfer transition. In Raman spectra, as the excitation approaches the resonance region, the primary enhancement of aromatic ring modes was mainly observed, rather than intensification of the vinylic double-bond stretch. Under the experimental conditions it was observed that formation of polystyrene takes place, as showed by 1H NMR spectra, and the most significant interaction occurs at the aromatic ring, as supported by the results from interaction of TiCl4 with polystyrene, as indicated by the charge-transfer band and resonant intensification of the aromatic ring modes.

Analysis of fission-fragment mass distribution within the quantum-mechanical fragmentation theory

Energy Technology Data Exchange (ETDEWEB)

Singh, Pardeep; Kaur, Harjeet [Guru Nanak Dev University, Department of Physics, Amritsar (India)

2016-11-15

The fission-fragment mass distribution is analysed for the {sup 208}Pb({sup 18}O, f) reaction within the quantum-mechanical fragmentation theory (QMFT). The reaction potential has been calculated by taking the binding energies, Coulomb potential and proximity potential of all possible decay channels and a stationary Schroedinger equation has been solved numerically to calculate the fission-fragment yield. The overall results for mass distribution are compared with those obtained in experiment. Fine structure dips in yield, corresponding to fragment shell closures at Z = 50 and N=82, which are observed by Bogachev et al., are reproduced successfully in the present calculations. These calculations will help to estimate the formation probabilities of fission fragments and to understand many related phenomena occurring in the fission process. (orig.)

Synthesis of Hollow Conductive Polypyrrole Balls by the Functionalized Polystyrene as Template

Directory of Open Access Journals (Sweden)

Choo Hwan Chang

2010-01-01

Full Text Available We report the preparation of hollow spherical polypyrrole balls (HSPBs by two different approaches. In the first approach, core-shell conductive balls, CSCBs, were prepared with poly(styrene as core and polypyrrole (PPy as shell by in situ polymerization of pyrrole in the presence of polystyrene (PS latex particles. In the other approach, CSCBs were obtained by in situ copolymerization of pyrrole in the presence of PS(F with hydrophilic groups like anhydride, boronic acid, carboxylic acid, or sulfonic acid, and then HSPBs were obtained by the removal of PS or PS(F core from CSCBs. TEM images reveal the spherical morphology for HSPBs prepared from PS(F. The conductivity of CSCBs and HSPBs was in the range of 0.20–0.90 S/cm2.

Morphology and Viscoelastic Properties of Polystyrene Blended with Fully Condensed Polyhedral Oligomeric Silsesquioxanes

National Research Council Canada - National Science Library

Namani, Madhu; Geng, Hai-Ping; Lee, Andre; Blanski, Rusty L

2004-01-01

.... Experiments were performed using a nearly-monodisperse molecular weight polystyrene (PS) blended with varying amounts of two fully condensed POSS molecules surrounded with phenethyl and styrenyl groups...

Preparation of polystyrene microsphere with emulsion microencapsulation method

International Nuclear Information System (INIS)

Li Bo Zhang Lin; Zhang Zhganwen; You Dan; Wei Yun; Wang Chaoyang; Lin Bo; Shi Tao; Chu Qiaomei

2003-01-01

The preparation of hollow polystyrene microspheres that are used as inner shell of multi-shell plastic microspheres in the ICF experiments is focused on. The effects of surfactants, water-soluble polymer and electrolyte on the properties of resultant microspheres are studied. Based on these experiments, a fabricating procedure was established with which hollow microspheres were prepared with diameter about 150-3000 μm, wall thickness 0.8-15 μm and toughness Ra less than 4 nm. (authors)

Extension of the pseudo dynamic method to test structures with distributed mass

International Nuclear Information System (INIS)

Renda, V.; Papa, L.; Bellorini, S.

1993-01-01

The PsD method is a mixed numerical and experimental procedure. At each time step the dynamic deformation of the structure, computed by solving the equation of the motion for a given input signal, is reproduced in the laboratory by means of actuators attached to the sample at specific points. The reaction forces at those points are measured and used to compute the deformation for the next time step. The reaction forces being known, knowledge of the stiffness of the structure is not needed, so that the method can be effective also for deformations leading to strong nonlinear behaviour of the structure. On the contrary, the mass matrix and the applied forces must be well known. For this reason the PsD method can be applied without approximations when the masses can be considered as lumped at the testing points of the sample. The present work investigates the possibility to extend the PsD method to test structures with distributed mass. A standard procedure is proposed to provide an equivalent mass matrix and force vector reduced to the testing points and to verify the reliability of the model. The verification is obtained comparing the results of multi-degrees of freedom dynamic analysis, done by means of a Finite Elements (FE) numerical program, with a simulation of the PsD method based on the reduced degrees of freedom mass matrix and external forces, assuming in place of the experimental reactions, those computed with the general FE model. The method has been applied to a numerical simulation of the behaviour of a realistic and complex structure with distributed mass consisting of a masonry building of two floors. The FE model consists of about two thousand degrees of freedom and the condensation has been made for four testing points. A dynamic analysis has been performed with the general FE model and the reactions of the structure have been recorded in a file and used as input for the PsD simulation with the four degree of freedom model. The comparison between

A Detailed Study of the Mass Distribution of the Galaxy Cluster RXC J2248.7-4431

International Nuclear Information System (INIS)

Caminha, G B; Rosati, P; Grillo, C

2016-01-01

In this work we use strong gravitational lensing techniques to constrain the total mass distribution of the galaxy cluster RXC J2248.7-4432 (RXC J2248, z lens = 0.348), also known as Abell S1063, observed within the Cluster Lensing And Supernova survey with Hubble (CLASH). Thanks to its strong lensing efficiency and exceptional data quality from the VIsible Multi-Object Spectrograph (VIMOS) and Multi Unit Spectroscopic Explorer (MUSE) on the Very Large Telescope, we can build a parametric model for the total mass distribution. Using the positions of the multiple images generated by 7 multiply-lensed background sources with measured spectroscopic redshifs, we find that the best-fit parametrisation for the cluster total mass distribution is composed of an elliptical pseudo-isothermal mass distribution with a significant core for the overall cluster halo, and of truncated pseudo-isothermal mass profiles for the cluster galaxies. This model is capable to predict the positions of the multiple images with an unprecedented precision of ≈ 0”.3. We also show that varying freely the cosmological parameters of the ΛCDM model, our strong lensing model can constrain the underlying geometry of the universe via the angular diameter distances between the lens and the sources and the observer and the sources. (paper)

Attentionally splitting the mass distribution of hand-held rods.

Science.gov (United States)

Burton, G; Turvey, M T

1991-08-01

Two experiments on the length-perception capabilities of effortful or dynamic touch differed only in terms of what the subject intended to perceive, while experimental conditions and apparatus were held constant. In each trial, a visually occluded rod was held as still as possible by the subject at an intermediate position. For two thirds of the trials, a weight was attached to the rod above or below the hand. In Experiment 1, in which the subject's task was to perceive the distance reachable with the portion of the rod forward of the hand, perceived extent was a function of the first moment of the mass distribution associated with the forward portion of the rod, and indifferent to the first moment of the entire rod. In Experiment 2, in which the task was to perceive the distance reachable with the entire rod if it was held at an end, the pattern of results was reversed. These results indicate the capability of selective sensitivity to different aspects of a hand-held object's mass distribution, without the possibility of differential exploration specific to these two tasks. Results are discussed in relation to possible roles of differential information, intention, and self-organization in the explanations of selective perceptual abilities.

Fast synthesis, formation mechanism, and control of shell thickness of CuS–polystyrene core–shell microspheres

International Nuclear Information System (INIS)

Zhao, Li-min; Shao, Xin; Yin, Yi-bin; Li, Wen-zhi

2012-01-01

Graphical abstract: Core–shell structure PSt/CuS were prepared using polystyrene which were modified by 3-methacryloxypropyltrimethoxysilane as template. The coating thickness of CuS can be controlled by the amount of 3-methacryloxypropyltrimethoxysilane and the UV–vis absorption intensity of PSt/CuS composite also changed with the coating thickness of CuS. Highlights: ► Core–shell structure PSt/CuS were prepared using silanol-modified polystyrene microspheres as template. ► The coating thickness of core–shell structure PSt/CuS can be controlled by a simple method. ► The UV–vis absorption intensity of PSt/CuS composite also changed with the coating thickness of CuS. -- Abstract: The silanol-modified polystyrene microspheres were prepared through dispersion polymerization. Then copper sulfide particles were grown on silanol-modified polystyrene through sonochemical deposition in an aqueous bath containing copper acetate and sulfide, released through the hydrolysis of thioacetamide. The resulting particles were continuous and uniform as characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Fourier transform infrared, thermogravimetric analysis and UV–vis absorption spectroscopy were used to characterize the structure and properties of core–shell particles. The results showed the coating thickness of CuS shell can be controlled by the amount of silanol and the UV–vis absorption intensity of PSt/CuS composite also changed with the coating thickness of CuS.

Renewable Aromatics from the Degradation of Polystyrene under Mild Conditions

KAUST Repository

Al Jabri, Nouf M.

2017-08-01

Polystyrene (PS) is one of the most important polymers in the plastic sector due to its inexpensive cost as well as many preferred properties. Its international market is expected to achieve $28.2 billion by 2019. Although PS has a high calorific value of 87 GJ tonne-1, there is no a practical method to manage its waste but landfill. As a result, the PS debris in the oceans has reached 70% of the total plastic debris. This issue is considered as the main economical and environmental drivers of converting polystyrene waste into renewable chemical feedstocks. The aim of this work is to develop a catalyst for converting PS into renewable chemicals under mild conditions. We introduce FeCu/Alumina with excellent catalytic activity to fully degrade polystyrene with 66% liquid yield at 250 °C. The GC/MS confirmed that the primary products are in the gasoline range. Next, we present the bimetallic FeCo/Alumina and successfully we have obtained 100% PS conversion and 90% liquid yield with maintaining the products selectivity. Later, the tri-metallic FeCuCo/Alumina was synthesized and showed 100% PS conversion and 91% liquid yield. Surprisingly, ethylbenzene was the major product in which 80 wt. % was achieved with excellent reproducibility. Furthermore, the real waste Styrofoam was thermally and catalytically degraded at 250 °C. Interestingly, a high styrene content of 78 wt. % was recovered after 30 minutes of the reaction under mild conditions. Keeping in mind that a good balance between acidity and basicity is required to convert PS into aromatic under mild reaction conditions catalytically. Finally, the performance of the catalysts was compared to literature reports and showed novel liquid yields. In conclusion, we have synthesized cheap, easy to scale up, and efficient catalysts to fully degrade PS into high liquid yields of aromatics with excellent selectivity.

Fluorescent QDs-polystyrene composite nanospheres for highly efficient and rapid protein antigen detection

Energy Technology Data Exchange (ETDEWEB)

Zhou, Changhua; Mao, Mao [Henan University, Key Laboratory for Special Functional Materials of the Ministry of Education (China); Yuan, Hang [Tsinghua University, Life Science Division, Graduate School at Shenzhen (China); Shen, Huaibin [Henan University, Key Laboratory for Special Functional Materials of the Ministry of Education (China); Wu, Feng; Ma, Lan, E-mail: malan@sz.tsinghua.edu.cn [Tsinghua University, Life Science Division, Graduate School at Shenzhen (China); Li, Lin Song, E-mail: lsli@henu.edu.cn [Henan University, Key Laboratory for Special Functional Materials of the Ministry of Education (China)

2013-09-15

In this paper, high-quality carboxyl-functionalized fluorescent (red, green, and blue emitting) nanospheres (46-103 nm) consisting of hydrophobic quantum dots (QDs) and polystyrene were prepared by a miniemulsion polymerization approach. This miniemulsion polymerization approach induced a homogeneous distribution and high aqueous-phase transport efficiency of fluorescent QDs in composite nanospheres, which proved the success of our encoding QDs strategy. The obtained fluorescent nanospheres exhibited high stability in aqueous solution under a wide range of pH, different salt concentrations, PBS buffer, and thermal treatment at 80 Degree-Sign C. Based on the red emitting composite nanosphere, we performed fluorescent lateral flow immunoassay (LFIA) strips for high-sensitivity and rapid alpha-fetal protein detection. The detection limit reached 0.1 ng/mL, which was 200 times higher than commercial colloidal gold-labeled LFIA strips, and it reached similar detection level in enzyme-linked immunosorbent assay kit.

Polystyrene/magnetite nanocomposite synthesis and characterization: investigation of magnetic and electrical properties for using as microelectromechanical systems (MEMS

Directory of Open Access Journals (Sweden)

Omidi Mohammad Hassan

2017-02-01

Full Text Available In this work, a novel polystyrene/Fe3O4 nanocomposite prepared by in-situ method is presented. Magnetic Fe3O4 nanoparticles were encapsulated by polystyrene. The FT-IR spectra confirmed polystyrene/Fe3O4 nanocomposite preparation. The electrical properties of prepared nanocomposite were investigated by cyclic voltammetry (CV. The CV analysis showed good electrical conductivity of the synthesized nanocomposite. Magnetic properties of the nanocomposite were studied by vibrating sample magnetometer (VSM. The VSM analysis confirmed magnetic properties of the nanocomposite. The morphology and the size of the synthesized nanocomposite were investigated by field emission scanning electron microscope (FESEM. According to the VSM and CV results, such nanocomposite can be used in microelectromechanical systems.

Long-term clearance of inhaled magnetite and polystyrene latex from the lung: a comparison

Energy Technology Data Exchange (ETDEWEB)

Schlesinger, R.B.; Halpern, M.; Lippmann, M. (New York Univ., NY (USA). Inst. of Environmental Medicine)

1982-01-01

As part of a larger study evaluating the applicability of a magnetic detection technique for monitoring lung retention of inhaled particles, simultaneous radiological measurements of the retention of magnetite and polystyrene latex particles in four donkeys were performed. The radiometric measurements were performed using a scintillation detector series modified for separation of the higher energy ..gamma..-emissions of /sup 59/Fe and /sup 85/Sr. In all animals, after 24 hr post-exposure, both polystyrene and magnetite exhibited a relatively rapid phase for 80 days (Tsub(1/2) = 15-22 days) which, in three donkeys, was clearly followed by a slower phase (Tsub(1/2) = 42-173 days); activity levels after 80 days in the fourth donkey were too low to permit determination of clearance rate. During the second phase, a deviation in pattern was clearly observed between the two aerosols, the polystyrene being cleared consistently faster than the magnetite. It is suggested that this deviation implies that, beginning at this time, there were functional differences between the dominant clearance mechanisms for the two aerosols. Exactly what these mechanisms were, or whether the difference was attributable to specific differences in particle characteristics, could not be determined.

Long-term clearance of inhaled magnetite and polystyrene latex from the lung: a comparison

International Nuclear Information System (INIS)

Schlesinger, R.B.; Halpern, M.; Lippmann, M.

1982-01-01

As part of a larger study evaluating the applicability of a magnetic detection technique for monitoring lung retention of inhaled particles, simultaneous radiological measurements of the retention of magnetite and polystyrene latex particles in four donkeys were performed. The radiometric measurements were performed using a scintillation detector series modified for separation of the higher energy γ-emissions of 59 Fe and 85 Sr. In all animals, after 24 hr post-exposure, both polystyrene and magnetite exhibited a relatively rapid phase for 80 days (Tsub(1/2) = 15-22 days) which, in three donkeys, was clearly followed by a slower phase (Tsub(1/2) = 42-173 days); activity levels after 80 days in the fourth donkey were too low to permit determination of clearance rate. During the second phase, a deviation in pattern was clearly observed between the two aerosols, the polystyrene being cleared consistently faster than the magnetite. It is suggested that this deviation implies that, beginning at this time, there were functional differences between the dominant clearance mechanisms for the two aerosols. Exactly what these mechanisms were, or whether the difference was attributable to specific differences in particle characteristics, could not be determined. (U.K.)

Synthesis of well-defined polystyrene macrophotoinitiators by ATRP

International Nuclear Information System (INIS)

Degirmenci, M.

2004-01-01

Macrophotointiators are polymers with a photoinitiator functionality at side chains or in the end or middle of the chain. these materials are of great scientific and technological interest because of their application in UV-curable coatings and as precursors for graft and block copolymers depending on the position of the photoinitiator moiety incorporated. Many macrophotoinitiators have been synthesized and their utilization in both applications have been studied. The major concern for their uses particulary in the latter application was related to the efficiency of functionalization, well-defined and predetermined structures, and low polydispersities. Obviously, if the all chains are not functionalized, upon irradiation non-funtionalized chains will not be activated and consequently remain as homopolymers in the system. In this study, new mono and bifunctional atom transfer radical polymerization (ATRP) initionars were synthesized by the condensation of 2-bromopropanoyl bromide with 2-hydroxy-2-methyl-1-phenyl propan-1-one (HMPP) and 2-hydroxy-1-(4-(2-hydroxyethoxy) phenyl)-2-methyl propan-1-one (HE-HMPP), respectively and characterized. The ATRP of styrene (St) in bulk at 110 degrees by means of these initiators in conjunction with a cuprous complex Cu(I) Br/bipyridine yields polystyrenes with photoactive alkoxy phenylketone groups. GPC, spectroscopic and photodegradation studies revealed that the initiation efficiency was quantitative and low-polydispersity polystyrenes with photoinitiator functionality in the end or middle of chain were obtained

The ATLAS3D project - XX. Mass-size and mass-σ distributions of early-type galaxies: bulge fraction drives kinematics, mass-to-light ratio, molecular gas fraction and stellar initial mass function

Science.gov (United States)

Cappellari, Michele; McDermid, Richard M.; Alatalo, Katherine; Blitz, Leo; Bois, Maxime; Bournaud, Frédéric; Bureau, M.; Crocker, Alison F.; Davies, Roger L.; Davis, Timothy A.; de Zeeuw, P. T.; Duc, Pierre-Alain; Emsellem, Eric; Khochfar, Sadegh; Krajnović, Davor; Kuntschner, Harald; Morganti, Raffaella; Naab, Thorsten; Oosterloo, Tom; Sarzi, Marc; Scott, Nicholas; Serra, Paolo; Weijmans, Anne-Marie; Young, Lisa M.

2013-07-01

In the companion Paper XV of this series, we derive accurate total mass-to-light ratios (M/L)_JAM≈ (M/L)({r}= {R_e}) within a sphere of radius r= {R_e} centred on the galaxy, as well as stellar (M/L)stars (with the dark matter removed) for the volume-limited and nearly mass-selected (stellar mass M_star ≳ 6× 10^9 { M_{⊙}}) ATLAS3D sample of 260 early-type galaxies (ETGs, ellipticals Es and lenticulars S0s). Here, we use those parameters to study the two orthogonal projections ({M_JAM}, {σ _e}) and ({M_JAM}, {R_e^maj}) of the thin Mass Plane (MP) ({M_JAM}, {σ _e}, {R_e^maj}) which describes the distribution of the galaxy population, where {M_JAM}≡ L× (M/L)_JAM≈ M_star. The distribution of galaxy properties on both projections of the MP is characterized by: (i) the same zone of exclusion (ZOE), which can be transformed from one projection to the other using the scalar virial equation. The ZOE is roughly described by two power laws, joined by a break at a characteristic mass {M_JAM}≈ 3× 10^{10} { M_{⊙}}, which corresponds to the minimum Re and maximum stellar density. This results in a break in the mean {M_JAM}-{σ _e} relation with trends {M_JAM}∝ σ _e^{2.3} and {M_JAM}∝ σ _e^{4.7} at small and large σe, respectively; (ii) a characteristic mass {M_JAM}≈ 2× 10^{11} { M_{⊙}} which separates a population dominated by flat fast rotator with discs and spiral galaxies at lower masses, from one dominated by quite round slow rotators at larger masses; (iii) below that mass the distribution of ETGs' properties on the two projections of the MP tends to be constant along lines of roughly constant σe, or equivalently along lines with {R_e^maj}∝ {M_JAM}, respectively (or even better parallel to the ZOE: {R_e^maj}∝ M_JAM^{0.75}); (iv) it forms a continuous and parallel sequence with the distribution of spiral galaxies; (v) at even lower masses, the distribution of fast-rotator ETGs and late spirals naturally extends to that of dwarf ETGs (Sph

Fluorescent polystyrene photonic crystals self-assembled with water-soluble conjugated polyrotaxanes

Directory of Open Access Journals (Sweden)

Francesco Di Stasio

2013-10-01

Full Text Available We demonstrate control of the photoluminescence spectra and decay rates of water-soluble green-emitting conjugated polyrotaxanes by incorporating them in polystyrene opals with a stop-band spectrally tuned on the rotaxane emission (405–650 nm. We observe a suppression of the luminescence within the photonic stop-band and a corresponding enhancement of the high-energy edge (405–447 nm. Time-resolved measurements reveal a wavelength-dependent modification of the emission lifetime, which is shortened at the high-energy edge (by ∼11%, in the range 405–447 nm, but elongated within the stop-band (by ∼13%, in the range 448–482 nm. We assign both effects to the modification of the density of photonic states induced by the photonic crystal band structure. We propose the growth of fluorescent composite photonic crystals from blends of “solvent-compatible” non-covalently bonded nanosphere-polymer systems as a general method for achieving a uniform distribution of polymeric dopants in three-dimensional self-assembling photonic structures.

Photothermal therapy of Lewis lung carcinoma in mice using gold nanoshells on carboxylated polystyrene spheres

Science.gov (United States)

Liu, Huiyu; Chen, Dong; Tang, Fangqiong; Du, Gangjun; Li, Linlin; Meng, Xianwei; Liang, Wei; Zhang, Yangde; Teng, Xu; Li, Yi

2008-11-01

A new approach towards the design of gold nanoshells on carboxylated polystyrene spheres (GNCPSs) is reported here. Gold nanoshells were self-assembled on the surface of carboxylated polystyrene spheres by a seed growth method. Chitosan (CHI) was used as a functional agent of carboxylated polystyrene spheres for attaching gold seeds. The surface plasmon resonance (SPR) peak of GNCPSs can be tuned, greatly redshifted, over a broad spectral range including the near-infrared (NIR) wavelength region, which provides maximal penetration of light through tissue. Irradiation of GNCPSs at their peak extinction coefficient results in the conversion of light to heat energy that produces a local rise in temperature. Our study revealed that the Lewis lung carcinoma (LLC) in mice treated with GNCPSs exposed to a low dose of NIR light (808 nm, 4 W cm-2) induced irreversible tissue damage. The tumor volumes of the treatment group by GNCPSs were significantly lower than those of control groups, with an average inhibition rate over 55% (P<0.005). This study proves that GNCPSs are promising in plasmonic photothermal tumor therapy.

Photothermal therapy of Lewis lung carcinoma in mice using gold nanoshells on carboxylated polystyrene spheres

International Nuclear Information System (INIS)

Liu Huiyu; Chen Dong; Tang Fangqiong; Li Linlin; Meng Xianwei; Li Yi; Du Gangjun; Liang Wei; Zhang Yangde; Teng Xu

2008-01-01

A new approach towards the design of gold nanoshells on carboxylated polystyrene spheres (GNCPSs) is reported here. Gold nanoshells were self-assembled on the surface of carboxylated polystyrene spheres by a seed growth method. Chitosan (CHI) was used as a functional agent of carboxylated polystyrene spheres for attaching gold seeds. The surface plasmon resonance (SPR) peak of GNCPSs can be tuned, greatly redshifted, over a broad spectral range including the near-infrared (NIR) wavelength region, which provides maximal penetration of light through tissue. Irradiation of GNCPSs at their peak extinction coefficient results in the conversion of light to heat energy that produces a local rise in temperature. Our study revealed that the Lewis lung carcinoma (LLC) in mice treated with GNCPSs exposed to a low dose of NIR light (808 nm, 4 W cm -2 ) induced irreversible tissue damage. The tumor volumes of the treatment group by GNCPSs were significantly lower than those of control groups, with an average inhibition rate over 55% (P<0.005). This study proves that GNCPSs are promising in plasmonic photothermal tumor therapy.

Heparainization of gas plasma-modified polystyrene surfaces and the interactions of these surfaces with proteins studied with surface plasmon resonance

NARCIS (Netherlands)

van Delden, C.J.; van Delden, C.J.; Lens, J.P.; Lens, J.P.; Kooyman, R.P.H.; Engbers, G.H.M.; Feijen, Jan

1997-01-01

Polystyrene surfaces obtained by spin-coating a solution of polystyrene in toluene on a gold layer were functionalized with carboxylic acid groups by preadsorption of the sodium salt of undecylenic acid, followed by an argon plasma treatment. A conjugate of albumin and heparin (alb-hep) was

Synthesis and characterization of kaolin with polystyrene via in-situ polymerization and their application on polypropylene

International Nuclear Information System (INIS)

Zhao, Songfang; Qiu, Shangchang; Zheng, Yuying; Cheng, Lei; Guo, Yong

2011-01-01

To improve both the mechanical and thermal properties of kaolin/polypropylene (PP) composites, kaolin was modified by using 3-(trimethoxysilyl) propylmethacrylate (YDH-570) as a coupling agent to form polymerizable particle. Styrene was radically polymerized through the immobilized vinyl using benzoyl peroxide (BPO) as an initiator. Fourier transform-infrared (FTIR) spectroscopy, particle size distribution, X-ray diffraction (XRD) and thermo-gravimetric analysis (TGA) well demonstrated that the kaolin-polystyrene particles were successfully synthesized via in-situ polymerization. While the modified kaolin and raw kaolin were introduced into the PP matrix, it could be concluded that modified kaolin/PP composites have better mechanical and thermal properties than raw kaolin/PP composites, and these improvements were attributed to the desirable dispersion of kaolin in PP matrix.

Formation of Conjugated Double Bonds to Induce Polystyrene Conductivity by using Different Concentrations of Methoxo-Oxo Bis (8-Quinolyloxo Vanadium (V

Directory of Open Access Journals (Sweden)

Basim Mohamad Hasan

2017-02-01

Full Text Available The effect of different concentrations of additive compound methoxo–oxo bis (8-quinolyloxo vanadium (v on formation of conjugated double bonds as part of photo transformation of polystyrene has been investigated. The UV-Vis spectrophotometery has been used in this work. The results are show that additive concentrations applied increase the formation of conjugated double bond as compared with polystyrene. In this study methoxo – oxo bis (8-quinolyloxo vanadium (v indicates great activity to enhance the conductivity of polystyrene by formation of conjugated double bonds.

Rapid coagulation of polystyrene latex in a stopped-flow spectrophotometer

NARCIS (Netherlands)

Lichtenbelt, J.W.Th.; Pathmamanoharan, C.; Wiersema, P.H.

1974-01-01

With a stopped-flow method the rapid coagulation by electrolyte of several polystyrene latices is measured. By extrapolating back to zero time the initial process of two single particles forming a doublet is observed. We find an average rate constant ifk11 = 6.0 × 10−12 p−1 cm3 sec su−1 at 20°C,

Thermodynamic and Kinetic Behavior of the Polystyrene/Poly(vinyl methyl ether) Blend as Studied by Excimer Fluorescence.

Science.gov (United States)

1986-01-02

AD-A±63 895 THERMODYNAMIC AND KINETIC BEHAVIOR OF THE / POLYSTYRENE/POLY(YINYL METHYL E..(U) STANFORD UNIY CALIFDEPT OF CHEMICAL ENGINEERING C N...Polystyrene/Poly(vinyl methyl ether) Blend 7. DEcFRMN 81 toOR 30USptE8 00~ as Studied by Excimer Fluorescence 6 EFRIGOG EOTNME *AUTHOR() a. CONTRACT OR GRANT...werea fondoare ihemoriisof * ~ Ex e sp fluodecositionsdu to deud Gen e and hoog Pinus Florsneis shownhase migrationprocSECURITY CLASIFICTIO OFd

The impact of fluorescent dyes on the performances of polystyrene-based plastic scintillators

International Nuclear Information System (INIS)

Zhu, Jun; Deng, Cheng; Jiang, Huimin; Zheng, Zhanlong; Gong, Rui; Bi, Yutie; Zhang, Lin; Lin, Runxiong

2016-01-01

To investigate the influence of both the first luminescent additive and the wavelength-shifter on the performance of plastic scintillator, a series of polystyrene-based scintillator had been prepared by thermal polymerization. Three first luminescent additives (PPO, p-TP and b-PBD) and four wavelength-shifters (POPOP, Bis-MSB, Me-MSB and DPA) were added to the scintillators respectively. The comparison results showed that PPO and POPOP were the most adequate fluorescent dyes for the polystyrene-based plastic scintillator. Moreover, with the increase of the concentration of PPO and POPOP, the fluorescence intensity and light yield were increased firstly and then decreased. The plastic scintillator containing 2% PPO and 0.02% POPOP had the highest fluorescence intensity and light yield.

The impact of fluorescent dyes on the performances of polystyrene-based plastic scintillators

Energy Technology Data Exchange (ETDEWEB)

Zhu, Jun [Research Center of Laser Fusion, China Academy of Engineering Physics, Mianyang 621900 (China); Engineering Research Center of High Performance Polymer and Molding Technology, Ministry of Education, Qingdao University of Science and Technology, Qingdao 266042 (China); Joint Laboratory for Extreme Conditions Matter Properties, Southwest University of Science and Technology and Research Center of Laser Fusion, China Academy of Engineering Physics, Mianyang 621010 (China); Deng, Cheng; Jiang, Huimin [Engineering Research Center of High Performance Polymer and Molding Technology, Ministry of Education, Qingdao University of Science and Technology, Qingdao 266042 (China); Zheng, Zhanlong; Gong, Rui [Research Center of Laser Fusion, China Academy of Engineering Physics, Mianyang 621900 (China); Joint Laboratory for Extreme Conditions Matter Properties, Southwest University of Science and Technology and Research Center of Laser Fusion, China Academy of Engineering Physics, Mianyang 621010 (China); Bi, Yutie [Joint Laboratory for Extreme Conditions Matter Properties, Southwest University of Science and Technology and Research Center of Laser Fusion, China Academy of Engineering Physics, Mianyang 621010 (China); Zhang, Lin, E-mail: zhlmy@sina.com [Research Center of Laser Fusion, China Academy of Engineering Physics, Mianyang 621900 (China); Lin, Runxiong, E-mail: qdlrx@qust.edu.cn [Engineering Research Center of High Performance Polymer and Molding Technology, Ministry of Education, Qingdao University of Science and Technology, Qingdao 266042 (China)

2016-11-01

To investigate the influence of both the first luminescent additive and the wavelength-shifter on the performance of plastic scintillator, a series of polystyrene-based scintillator had been prepared by thermal polymerization. Three first luminescent additives (PPO, p-TP and b-PBD) and four wavelength-shifters (POPOP, Bis-MSB, Me-MSB and DPA) were added to the scintillators respectively. The comparison results showed that PPO and POPOP were the most adequate fluorescent dyes for the polystyrene-based plastic scintillator. Moreover, with the increase of the concentration of PPO and POPOP, the fluorescence intensity and light yield were increased firstly and then decreased. The plastic scintillator containing 2% PPO and 0.02% POPOP had the highest fluorescence intensity and light yield.

Synthesis and self-assembly of Chitosan-g-Polystyrene copolymer: A new route for the preparation of heavy metal nanoparticles

KAUST Repository

Francis, Raju S.

2015-01-01

Amphiphilic graft copolymers made of a Chitosan (CS) backbone and three arm polystyrene (PS) grafts were prepared by "grafting onto" strategy using Toluene Diisocyanate. IR spectroscopy and SEC show the successful grafting process. SEM pictures of Chitosan-g-Polystyrene (CS-g-PS) indicate a spherulite like surface and exhibit properties that result from the disappearance of Chitosan crystallinity. The introduced polystyrene star grafts units improve hydrophobic properties considerably as confirmed by the very high solubility of (CS-g-PS) in organic solvents. The graft copolymer which self-assembles into polymeric micelles in organic media demonstrates much better adsorption of transition and inner transition metal ions than pure Chitosan whose amine groups are not necessarily available due to crystallinity.

The relationship between cellular adhesion and surface roughness in polystyrene modified by microwave plasma radiation

Directory of Open Access Journals (Sweden)

Biazar E

2011-03-01

Full Text Available Esmaeil Biazar1, Majid Heidari2, Azadeh Asefnezhad2, Naser Montazeri11Department of Chemistry, Islamic Azad University, Tonekabon Branch, Mazandaran; 2Department of Biomaterial Engineering, Faculty of Biomedical Engineering, Science and Research Branch, Islamic Azad University, Tehran, IranBackground: Surface modification of medical polymers can improve biocompatibility. Pure polystyrene is hydrophobic and cannot provide a suitable environment for cell cultures. The conventional method for surface modification of polystyrene is treatment with plasma. In this study, conventional polystyrene was exposed to microwave plasma treatment with oxygen and argon gases for 30, 60, and 180 seconds.Methods and results: Attenuated total reflection Fourier transform infrared spectra investigations of irradiated samples indicated clearly the presence of functional groups. Atomic force microscopic images of samples irradiated with inert and active gases indicated nanometric surface topography. Samples irradiated with oxygen plasma showed more roughness (31 nm compared with those irradiated with inert plasma (16 nm at 180 seconds. Surface roughness increased with increasing duration of exposure, which could be due to reduction of the contact angle of samples irradiated with oxygen plasma. Contact angle analysis showed reduction in samples irradiated with inert plasma. Samples irradiated with oxygen plasma showed a lower contact angle compared with those irradiated by argon plasma.Conclusion: Cellular investigations with unrestricted somatic stem cells showed better adhesion, cell growth, and proliferation for samples radiated by oxygen plasma with increasing duration of exposure than those of normal samples.Keywords: surface topography, polystyrene, plasma treatment, argon, oxygen

Effects of gamma irradiation on food contact polyethylene, polypropylene and polystyrene. Volatiles

International Nuclear Information System (INIS)

Kawamura, Yoko; Sayama, Kayo; Yamada, Takashi

2000-01-01

The effects of gamma irradiation on the generation of volatiles from food contact polyethylene and polypropylene were investigated using head space (HS)/GC/MS. All samples generated volatiles such as acetic acid, propionic acid, butanoic acid, 2,2-dimethylpropionic acid, acetone, 2-butanone, 2-propanol, 2-methyl-2-propanol, hydrocarbons, etc., due to the gamma irradiation. Especially, acetic acid and acetone were formed in greatest amounts. Since these volatiles did not exist before irradiation and their amounts increased with increasing irradiation dose, they should be degradation products from the polymer or additives by irradiation. Polypropylene generated more kinds and larger amounts of volatiles than polyethylene, which showed that polypropylene is more sensitive to irradiation. Polystyrene contained styrene and ethylbenzene as monomers before irradiation and their amounts decreased after irradiation. Polystyrene generated few degradation products during the irradiation. (author)

Teacher candidates' mastery of phoneme-grapheme correspondence: massed versus distributed practice in teacher education.

Science.gov (United States)

Sayeski, Kristin L; Earle, Gentry A; Eslinger, R Paige; Whitenton, Jessy N

2017-04-01

Matching phonemes (speech sounds) to graphemes (letters and letter combinations) is an important aspect of decoding (translating print to speech) and encoding (translating speech to print). Yet, many teacher candidates do not receive explicit training in phoneme-grapheme correspondence. Difficulty with accurate phoneme production and/or lack of understanding of sound-symbol correspondence can make it challenging for teachers to (a) identify student errors on common assessments and (b) serve as a model for students when teaching beginning reading or providing remedial reading instruction. For students with dyslexia, lack of teacher proficiency in this area is particularly problematic. This study examined differences between two learning conditions (massed and distributed practice) on teacher candidates' development of phoneme-grapheme correspondence knowledge and skills. An experimental, pretest-posttest-delayed test design was employed with teacher candidates (n = 52) to compare a massed practice condition (one, 60-min session) to a distributed practice condition (four, 15-min sessions distributed over 4 weeks) for learning phonemes associated with letters and letter combinations. Participants in the distributed practice condition significantly outperformed participants in the massed practice condition on their ability to correctly produce phonemes associated with different letters and letter combinations. Implications for teacher preparation are discussed.

Using high performance interconnects in a distributed computing and mass storage environment

International Nuclear Information System (INIS)

Ernst, M.

1994-01-01

Detector Collaborations of the HERA Experiments typically involve more than 500 physicists from a few dozen institutes. These physicists require access to large amounts of data in a fully transparent manner. Important issues include Distributed Mass Storage Management Systems in a Distributed and Heterogeneous Computing Environment. At the very center of a distributed system, including tens of CPUs and network attached mass storage peripherals are the communication links. Today scientists are witnessing an integration of computing and communication technology with the open-quote network close-quote becoming the computer. This contribution reports on a centrally operated computing facility for the HERA Experiments at DESY, including Symmetric Multiprocessor Machines (84 Processors), presently more than 400 GByte of magnetic disk and 40 TB of automoted tape storage, tied together by a HIPPI open-quote network close-quote. Focussing on the High Performance Interconnect technology, details will be provided about the HIPPI based open-quote Backplane close-quote configured around a 20 Gigabit/s Multi Media Router and the performance and efficiency of the related computer interfaces

Polystyrene nanoparticles affect Xenopus laevis development

Energy Technology Data Exchange (ETDEWEB)

Tussellino, Margherita; Ronca, Raffaele [University of Naples Federico II, Department of Biology (Italy); Formiggini, Fabio [Italian Institute of Technology, Center for Advanced Biomaterials for Health Care IIT@CRIB (Italy); Marco, Nadia De [University of Naples Federico II, Department of Biology (Italy); Fusco, Sabato; Netti, Paolo Antonio [Italian Institute of Technology, Center for Advanced Biomaterials for Health Care IIT@CRIB (Italy); Carotenuto, Rosa, E-mail: rosa.carotenuto@unina.it [University of Naples Federico II, Department of Biology (Italy)

2015-02-15

Exposing living organisms to nanoparticulates is potentially hazardous, in particular when it takes place during embryogenesis. In this investigation, we have studied the effects of 50-nm-uncoated polystyrene nanoparticles (PSNPs) as a model to investigate the suitability of their possible future employments. We have used the standardized Frog Embryo Teratogenesis Assay-Xenopus test during the early stages of larval development of Xenopus laevis, and we have employed either contact exposure or microinjections. We found that the embryos mortality rate is dose dependent and that the survived embryos showed high percentage of malformations. They display disorders in pigmentation distribution, malformations of the head, gut and tail, edema in the anterior ventral region, and a shorter body length compared with sibling untreated embryos. Moreover, these embryos grow more slowly than the untreated embryos. Expressions of the mesoderm markers, bra (T-box Brachyury gene), myod1 (myogenic differentiation1), and of neural crest marker sox9 (sex SRY (determining region Y-box 9) transcription factor sox9), are modified. Confocal microscopy showed that the nanoparticles are localized in the cytoplasm, in the nucleus, and in the periphery of the digestive gut cells. Our data suggest that PSNPs are toxic and show a potential teratogenic effect for Xenopus larvae. We hypothesize that these effects may be due either to the amount of NPs that penetrate into the cells and/or to the “corona” effect caused by the interaction of PSNPs with cytoplasm components. The three endpoints of our study, i.e., mortality, malformations, and growth inhibition, suggest that the tests we used may be a powerful and flexible bioassay in evaluating pollutants in aquatic embryos.

Polystyrene nanoparticles affect Xenopus laevis development

International Nuclear Information System (INIS)

Tussellino, Margherita; Ronca, Raffaele; Formiggini, Fabio; Marco, Nadia De; Fusco, Sabato; Netti, Paolo Antonio; Carotenuto, Rosa

2015-01-01

Exposing living organisms to nanoparticulates is potentially hazardous, in particular when it takes place during embryogenesis. In this investigation, we have studied the effects of 50-nm-uncoated polystyrene nanoparticles (PSNPs) as a model to investigate the suitability of their possible future employments. We have used the standardized Frog Embryo Teratogenesis Assay-Xenopus test during the early stages of larval development of Xenopus laevis, and we have employed either contact exposure or microinjections. We found that the embryos mortality rate is dose dependent and that the survived embryos showed high percentage of malformations. They display disorders in pigmentation distribution, malformations of the head, gut and tail, edema in the anterior ventral region, and a shorter body length compared with sibling untreated embryos. Moreover, these embryos grow more slowly than the untreated embryos. Expressions of the mesoderm markers, bra (T-box Brachyury gene), myod1 (myogenic differentiation1), and of neural crest marker sox9 (sex SRY (determining region Y-box 9) transcription factor sox9), are modified. Confocal microscopy showed that the nanoparticles are localized in the cytoplasm, in the nucleus, and in the periphery of the digestive gut cells. Our data suggest that PSNPs are toxic and show a potential teratogenic effect for Xenopus larvae. We hypothesize that these effects may be due either to the amount of NPs that penetrate into the cells and/or to the “corona” effect caused by the interaction of PSNPs with cytoplasm components. The three endpoints of our study, i.e., mortality, malformations, and growth inhibition, suggest that the tests we used may be a powerful and flexible bioassay in evaluating pollutants in aquatic embryos

Mass size distribution of particle-bound water

Science.gov (United States)

Canepari, S.; Simonetti, G.; Perrino, C.

2017-09-01

The thermal-ramp Karl-Fisher method (tr-KF) for the determination of PM-bound water has been applied to size-segregated PM samples collected in areas subjected to different environmental conditions (protracted atmospheric stability, desert dust intrusion, urban atmosphere). This method, based on the use of a thermal ramp for the desorption of water from PM samples and the subsequent analysis by the coulometric KF technique, had been previously shown to differentiate water contributes retained with different strength and associated to different chemical components in the atmospheric aerosol. The application of the method to size-segregated samples has revealed that water showed a typical mass size distribution in each one of the three environmental situations that were taken into consideration. A very similar size distribution was shown by the chemical PM components that prevailed during each event: ammonium nitrate in the case of atmospheric stability, crustal species in the case of desert dust, road-dust components in the case of urban sites. The shape of the tr-KF curve varied according to the size of the collected particles. Considering the size ranges that better characterize the event (fine fraction for atmospheric stability, coarse fraction for dust intrusion, bi-modal distribution for urban dust), this shape is coherent with the typical tr-KF shape shown by water bound to the chemical species that predominate in the same PM size range (ammonium nitrate, crustal species, secondary/combustion species - road dust components).

Mass distributions in monoenergetic-neutron-induced fission of 232Th

International Nuclear Information System (INIS)

Glendenin, L.E.; Gindler, J.E.; Ahmad, I.; Henderson, D.J.; Meadows, J.W.

1980-01-01

Fission product yields for 38 masses were determined for the fission of 232 Th with essentially monoenergetic neutrons of 2.0, 3.0, 4.0, 5.9, 6.4, 6.9, 7.6, and 8.0 MeV. Fission product activities were measured by Ge(Li) γ-ray spectrometry of irradiated 232 Th foils and by chemical separation of the fission product elements followed by β counting. The mass yield data for 232 Th(n,f ) show a sensitive increase of fission yields in the near-symmetric mass region (valley) with increasing incident neutron energy E/sub n/ and a pronounced dip in yield at the onset of second-chance fission just above the neutron binding energy (at approx. 6 MeV) where the excitation energy is lowered by competition with neutron evaporation prior to fission. The effect of second-chance fission is also seen in the yields of asymmetric peak products. A distinct third peak is observed at symmetry in the valley of the mass distribution, and enhanced yields are observed in the asymmetric peaks at masses associated with even Z (proton pairing effect). The fission yeilds of 232 Th(n,f ) are compared with those of 238 U(n,f ) and 232 Th

Measurement of the t anti-t invariant mass distribution and search for t anti-t resonances

Energy Technology Data Exchange (ETDEWEB)

Vaupel, Maren [Wuppertal U.

2006-03-01

In this thesis the measurement of the top-antitop invariant mass distribution and a search for top-antitop resonances is presented. This analysis has been performed in top-antitop events using 370 inverse pb of data collected with the D0 detector at the Tevatron collider from August 2002 to August 2004. The event selection made use of the b-jet identification via secondary vertices which enhanced the top-antitop fraction in the data sample considerably. The top-antitop invariant mass distribution was obtained from a kinematic fit where the mass of the W boson and the top quark were constraint to nominal values. The resulting distribution agrees well with the Standard Model prediction and no statistically significant deviation indicating a top-antitop resonance could be observed. Therefore, no evidence for new physics can be claimed. Model independent upper limits at 95% C.L. on the production cross section using a Bayesian method have been obtained for different hypothesized masses of a narrow-width heavy resonance decaying into top-antitop. Within a topcolor-assisted technicolor model, the existence of a leptophobic Z' boson with a width of 1.2% of its mass can be excluded at 95% C.L. for masses of M_Z' < 660 GeV.

Aerosol formation from high-velocity uranium drops: Comparison of number and mass distributions. Final report

Energy Technology Data Exchange (ETDEWEB)

Rader, D.J.; Benson, D.A.

1995-05-01

This report presents the results of an experimental study of the aerosol produced by the combustion of high-velocity molten-uranium droplets produced by the simultaneous heating and electromagnetic launch of uranium wires. These tests are intended to simulate the reduction of high-velocity fragments into aerosol in high-explosive detonations or reactor accidents involving nuclear materials. As reported earlier, the resulting aerosol consists mainly of web-like chain agglomerates. A condensation nucleus counter was used to investigate the decay of the total particle concentration due to coagulation and losses. Number size distributions based on mobility equivalent diameter obtained soon after launch with a Differential Mobility Particle Sizer showed lognormal distributions with an initial count median diameter (CMD) of 0.3 {mu}m and a geometric standard deviation, {sigma}{sub g} of about 2; the CMD was found to increase and {sigma}{sub g} decrease with time due to coagulation. Mass size distributions based on aerodynamic diameter were obtained for the first time with a Microorifice Uniform Deposit Impactor, which showed lognormal distributions with mass median aerodynamic diameters of about 0.5 {mu}m and an aerodynamic geometric standard deviation of about 2. Approximate methods for converting between number and mass distributions and between mobility and aerodynamic equivalent diameters are presented.

Aerosol formation from high-velocity uranium drops: Comparison of number and mass distributions. Final report

International Nuclear Information System (INIS)

Rader, D.J.; Benson, D.A.

1995-05-01

This report presents the results of an experimental study of the aerosol produced by the combustion of high-velocity molten-uranium droplets produced by the simultaneous heating and electromagnetic launch of uranium wires. These tests are intended to simulate the reduction of high-velocity fragments into aerosol in high-explosive detonations or reactor accidents involving nuclear materials. As reported earlier, the resulting aerosol consists mainly of web-like chain agglomerates. A condensation nucleus counter was used to investigate the decay of the total particle concentration due to coagulation and losses. Number size distributions based on mobility equivalent diameter obtained soon after launch with a Differential Mobility Particle Sizer showed lognormal distributions with an initial count median diameter (CMD) of 0.3 μm and a geometric standard deviation, σ g of about 2; the CMD was found to increase and σ g decrease with time due to coagulation. Mass size distributions based on aerodynamic diameter were obtained for the first time with a Microorifice Uniform Deposit Impactor, which showed lognormal distributions with mass median aerodynamic diameters of about 0.5 μm and an aerodynamic geometric standard deviation of about 2. Approximate methods for converting between number and mass distributions and between mobility and aerodynamic equivalent diameters are presented

Asymmetry distributions and mass effects in dijet-events at a polarized HERA

CERN Document Server

Maul, M; Mirkes, E; Rädel, G

1998-01-01

The asymmetry distributions for several kinematic variables are considered for finding a systematic way to maximize the signal for the extraction of the polarized gluon density. The relevance of mass effects for the corresponding dijet cross section is discussed and the different approximations for including mass effects are compared. We also compare via the programs PEPSI and MEPJET two different Monte Carlo (MC) approaches for simulating the expected signal in the dijet asymmetry at a polarized HERA.

Accurately controlled sequential self-folding structures by polystyrene film

Science.gov (United States)

Deng, Dongping; Yang, Yang; Chen, Yong; Lan, Xing; Tice, Jesse

2017-08-01

Four-dimensional (4D) printing overcomes the traditional fabrication limitations by designing heterogeneous materials to enable the printed structures evolve over time (the fourth dimension) under external stimuli. Here, we present a simple 4D printing of self-folding structures that can be sequentially and accurately folded. When heated above their glass transition temperature pre-strained polystyrene films shrink along the XY plane. In our process silver ink traces printed on the film are used to provide heat stimuli by conducting current to trigger the self-folding behavior. The parameters affecting the folding process are studied and discussed. Sequential folding and accurately controlled folding angles are achieved by using printed ink traces and angle lock design. Theoretical analyses are done to guide the design of the folding processes. Programmable structures such as a lock and a three-dimensional antenna are achieved to test the feasibility and potential applications of this method. These self-folding structures change their shapes after fabrication under controlled stimuli (electric current) and have potential applications in the fields of electronics, consumer devices, and robotics. Our design and fabrication method provides an easy way by using silver ink printed on polystyrene films to 4D print self-folding structures for electrically induced sequential folding with angular control.

[Simultaneous determination of 33 primary aromatic amines in polystyrene and polyethylene masterbatches for foods by ultra-performance liquid chromatography-tandem mass spectrometry

Science.gov (United States)

Man, Zhengyin; Wang, Quanlin; Li, Hesheng; Zhang, Aizhi; Shen, Jian

2015-03-01

A comprehensive analytical method based on ultra-performance liquid chromatography coupled with triple quadrupole mass spectrometry (UPLC-MS/MS) has been developed for the simultaneous determination of 33 primary aromatic amines (PAAs) in polystyrene (PS) and polyethylene (PE) masterbatches for foods. The PS masterbatches were dissolved with dichloromethane, and methanol was added to precipitate after extraction by ultrasound extraction. Then the extract was purified by passing through a carbon graphite solid phase extraction column. The PE masterbatches were swelled and extracted with dichloromethane by ultrasound. The purified PS solution and PE extract were concentrated, and diluted to 2 mL with methanol-water (1:9, v/v), and filtered through the membranes of 0.22 µm before UPLC-MS/MS analysis. The analytes were separated on a BEH Phenyl column (100 mm x 2.1 mm, 1.7 µm), eluted by gradient with 0.07% (v/v) formic acid in methanol-water (1:9, v/v). The PAAs were detected by UPLC-MS/MS under multiple reaction monitoring (MRM) mode and quantified by the internal standard method. The separation conditions, fragment voltages and collision energies were optimized. The impacts of extraction times, extraction solvents and concentration methods on recoveries were studied. The limits of detection for the 33 primary aromatic amines were 6-10 µg/kg, and the limits of quantitation were 20-30 µg/kg. The mean recoveries of the two different masterbatch products at three spiked levels of 20, 100, 200 µg/kg were 61.3%-119.8%, and the relative standard deviations were 1.4%-14.8%. The experimental results indicated that the method is simple, rapid, sensitive, accurate, and can meet the related requirements for determination.

Modeling The GRB Host Galaxy Mass Distribution: Are GRBs Unbiased Tracers of Star Formation?

Energy Technology Data Exchange (ETDEWEB)

Kocevski, Daniel; /KIPAC, Menlo Park; West, Andrew A.; /UC, Berkeley, Astron. Dept. /MIT, MKI; Modjaz, Maryam; /UC, Berkeley, Astron. Dept.

2009-08-03

We model the mass distribution of long gamma-ray burst (GRB) host galaxies given recent results suggesting that GRBs occur in low metallicity environments. By utilizing measurements of the redshift evolution of the mass-metallicity (M-Z) relationship for galaxies, along with a sharp host metallicity cut-off suggested by Modjaz and collaborators, we estimate an upper limit on the stellar mass of a galaxy that can efficiently produce a GRB as a function of redshift. By employing consistent abundance indicators, we find that sub-solar metallicity cut-offs effectively limit GRBs to low stellar mass spirals and dwarf galaxies at low redshift. At higher redshifts, as the average metallicity of galaxies in the Universe falls, the mass range of galaxies capable of hosting a GRB broadens, with an upper bound approaching the mass of even the largest spiral galaxies. We compare these predicted limits to the growing number of published GRB host masses and find that extremely low metallicity cut-offs of 0.1 to 0.5 Z{sub {circle_dot}} are effectively ruled out by a large number of intermediate mass galaxies at low redshift. A mass function that includes a smooth decrease in the efficiency of producing GRBs in galaxies of metallicity above 12+log(O/H){sub KK04} = 8.7 can, however, accommodate a majority of the measured host galaxy masses. We find that at z {approx} 1, the peak in the observed GRB host mass distribution is inconsistent with the expected peak in the mass of galaxies harboring most of the star formation. This suggests that GRBs are metallicity biased tracers of star formation at low and intermediate redshifts, although our model predicts that this bias should disappear at higher redshifts due to the evolving metallicity content of the universe.

MODELING THE GRB HOST GALAXY MASS DISTRIBUTION: ARE GRBs UNBIASED TRACERS OF STAR FORMATION?

International Nuclear Information System (INIS)

Kocevski, Daniel; West, Andrew A.; Modjaz, Maryam

2009-01-01

We model the mass distribution of long gamma-ray burst (GRB) host galaxies given recent results suggesting that GRBs occur in low-metallicity environments. By utilizing measurements of the redshift evolution of the mass-metallicity relationship for galaxies, along with a sharp host metallicity cutoff suggested by Modjaz and collaborators, we estimate an upper limit on the stellar mass of a galaxy that can efficiently produce a GRB as a function of redshift. By employing consistent abundance indicators, we find that subsolar metallicity cutoffs effectively limit GRBs to low-stellar mass spirals and dwarf galaxies at low redshift. At higher redshifts, as the average metallicity of galaxies in the Universe falls, the mass range of galaxies capable of hosting a GRB broadens, with an upper bound approaching the mass of even the largest spiral galaxies. We compare these predicted limits to the growing number of published GRB host masses and find that extremely low-metallicity cutoffs of 0.1 to 0.5 Z sun are effectively ruled out by a large number of intermediate mass galaxies at low redshift. A mass function that includes a smooth decrease in the efficiency of producing GRBs in galaxies of metallicity above 12+log(O/H) KK04 = 8.7 can, however, accommodate a majority of the measured host galaxy masses. We find that at z ∼ 1, the peak in the observed GRB host mass distribution is inconsistent with the expected peak in the mass of galaxies harboring most of the star formation. This suggests that GRBs are metallicity-biased tracers of star formation at low and intermediate redshifts, although our model predicts that this bias should disappear at higher redshifts due to the evolving metallicity content of the universe.

Mass spectrometric probes of metal cluster distributions and metastable ion decay

International Nuclear Information System (INIS)

Parks, E.K.; Liu, K.; Cole, S.K.; Riley, S.J.

1988-01-01

The study of metal clusters has provided both an opportunity and a challenge to the application of mass spectrometry. These days the most often-used technique for cluster generation - laser vaporization - leads to extensive distributions of cluster sizes, from one to perhaps thousands of atoms, and most studies reported to date use excimer laser ionization and time-of-flight mass spectrometry for cluster detection. Our apparatus is a simple one-stage TOF design employing Wiley-McLauren spatial focusing and a one-meter drift tube. In a second apparatus employing a pulsed valve in the cluster source, we see asymmetric broadening of niobium cluster mass peaks under multiphoton ionization conditions, indicating metastable decay of parent cluster ions. Other studies of niobium clusters have shown no such asymmetric peaks. 2 figs

Ternary hybrid polymeric nanocomposites through grafting of polystyrene on graphene oxide-TiO_2 by surface initiated atom transfer radical polymerization (SI-ATRP)

International Nuclear Information System (INIS)

Kumar, Arvind; Bansal, Ankushi; Behera, Babita; Jain, Suman L.; Ray, Siddharth S.

2016-01-01

A ternary hybrid of graphene oxide-titania-polystyrene (GO-TiO_2-PS) nanocomposite is developed where polystyrene composition is regulated by controlling growth of polymer chains and nanoarchitectonics is discussed. Graphene Oxide-TiO_2 (GO-TiO_2) nanocomposite is prepared by in-situ hydrothermal method and the surface is anchored with α-bromoisobutyryl bromide to activate GO-TiO_2 as initiator for polymerization. In-situ grafting of polystyrene through surface initiated atom transfer radical polymerization (SI- ATRP) on this Br-functionalized nano-composite initiator yields GO-TiO_2-PS ternary hybrid. Varying the monomer amount and keeping the concentration of initiator constant, polystyrene chain growth is regulated with narrow poly-dispersivity to achieve desired composition. This composite is well characterized by various analytical techniques like FTIR, XRD, DSC, SEM, TEM, and TGA. - Highlights: • Nanocomposite of ternary hybrid of GO-TiO_2 with polystyrene. • PS is surface grafted on GO-TiO_2. • Polymer chain lengths are well regulated by SI-ATRP living polymerization. • Thermal stability of this hybrid is relatively high.

Mass media health communication campaigns combined with health-related product distribution: a community guide systematic review.

Science.gov (United States)

Robinson, Maren N; Tansil, Kristin A; Elder, Randy W; Soler, Robin E; Labre, Magdala P; Mercer, Shawna L; Eroglu, Dogan; Baur, Cynthia; Lyon-Daniel, Katherine; Fridinger, Fred; Sokler, Lynn A; Green, Lawrence W; Miller, Therese; Dearing, James W; Evans, William D; Snyder, Leslie B; Kasisomayajula Viswanath, K; Beistle, Diane M; Chervin, Doryn D; Bernhardt, Jay M; Rimer, Barbara K

2014-09-01

Health communication campaigns including mass media and health-related product distribution have been used to reduce mortality and morbidity through behavior change. The intervention is defined as having two core components reflecting two social marketing principles: (1) promoting behavior change through multiple communication channels, one being mass media, and (2) distributing a free or reduced-price product that facilitates adoption and maintenance of healthy behavior change, sustains cessation of harmful behaviors, or protects against behavior-related disease or injury. Using methods previously developed for the Community Guide, a systematic review (search period, January 1980-December 2009) was conducted to evaluate the effectiveness of health communication campaigns that use multiple channels, including mass media, and distribute health-related products. The primary outcome of interest was use of distributed health-related products. Twenty-two studies that met Community Guide quality criteria were analyzed in 2010. Most studies showed favorable behavior change effects on health-related product use (a median increase of 8.4 percentage points). By product category, median increases in desired behaviors ranged from 4.0 percentage points for condom promotion and distribution campaigns to 10.0 percentage points for smoking-cessation campaigns. Health communication campaigns that combine mass media and other communication channels with distribution of free or reduced-price health-related products are effective in improving healthy behaviors. This intervention is expected to be applicable across U.S. demographic groups, with appropriate population targeting. The ability to draw more specific conclusions about other important social marketing practices is constrained by limited reporting of intervention components and characteristics. Published by Elsevier Inc.

Electrospinning fabrication and oxygen sensing properties of Cu(I) complex-polystyrene composite microfibrous membranes

Energy Technology Data Exchange (ETDEWEB)

Wang Liyan, E-mail: wanglykmmc@163.co [Department of Orthodontics, School of Stomatology, Fourth Military Medical University, XiAn (China); Xu Yun [Department of Orthodontics, School of Stomatology, KunMing Medical College, Kunming (China); Lin Zhu [Department of Orthodontics, School of Stomatology, Fourth Military Medical University, XiAn (China); Zhao Ning [Department of Orthodontics, School of Stomatology, West China College, SiChuan University, ChengDu (China); Xu Yanhua [Department of Orthodontics, School of Stomatology, KunMing Medical College, Kunming (China)

2011-07-15

In this paper, a phosphorescent Cu(I) complex of [Cu(POP)(ECI-Phen)]BF{sub 4}, where POP=bis[2-(diphenylphosphino)phenyl]ether, and ECI-Phen=1-ethyl-2-(N-ethyl-carbazole-yl-4-)imidazo[4,5-f]1,10-phenanthroline, is incorporated into a polystyrene matrix of polystyrene (PS) to form microfibers membranes. The possibility of using the resulted composite microfibrous membranes as an optical oxygen sensor is explored. Good linearity and short response time are obtained with a sensitivity of 9.8. These results suggest that phosphorescent [Cu(POP)(ECI-Phen)]BF{sub 4} is a promising candidate for oxygen-sensors and PS is an excellent matrix for oxygen sensing material because it owns a large surface-area-to-volume ratio and can supply a homogeneous matrix for probe molecules. Further analysis suggests that the molecular structure of diamine ligand in Cu(I) complexes is critical for sensitivity due to the characteristic electronic structure of excited state Cu(I) complexes. - Highlights: {yields} Cu(I) complex is incorporated into polystyrene matrix to form nanofibers. {yields} Resulted sample exhibit good linearity and short response time. {yields} PS is an excellent matrix for oxygen sensing material for probe molecules. {yields} Molecular structure of diamine ligand is critical for sensitivity.

Genotoxicity of styrene oligomers extracted from polystyrene intended for use in contact with food

Directory of Open Access Journals (Sweden)

Makoto Nakai

2014-01-01

Full Text Available Here, we conducted in vitro genotoxicity tests to evaluate the genotoxicity of styrene oligomers extracted from polystyrene intended for use in contact with food. Styrene oligomers were extracted with acetone and the extract was subjected to the Ames test (OECD test guideline No. 471 and the in vitro chromosomal aberration test (OECD test guideline No. 473 under good laboratory practice conditions. The concentrations of styrene dimers and trimers in the concentrated extract were 540 and 13,431 ppm, respectively. Extraction with acetone provided markedly higher concentrations of styrene oligomers compared with extraction with 50% ethanol aqueous solution, which is the food simulant currently recommended for use in safety assessments of polystyrene by both the United States Food and Drug Administration and the European Food Safety Authority. And these high concentrations of styrene dimers and trimers were utilized for the evaluation of genotoxicity in vitro. Ames tests using five bacterial tester strains were negative both in the presence or absence of metabolic activation. The in vitro chromosomal aberration test using Chinese hamster lung cells (CHL/IU was also negative. Together, these results suggest that the risk of the genotoxicity of styrene oligomers that migrate from polystyrene food packaging into food is very low.

Electrospinning fabrication and oxygen sensing properties of Cu(I) complex-polystyrene composite microfibrous membranes

International Nuclear Information System (INIS)

Wang Liyan; Xu Yun; Lin Zhu; Zhao Ning; Xu Yanhua

2011-01-01

In this paper, a phosphorescent Cu(I) complex of [Cu(POP)(ECI-Phen)]BF 4 , where POP=bis[2-(diphenylphosphino)phenyl]ether, and ECI-Phen=1-ethyl-2-(N-ethyl-carbazole-yl-4-)imidazo[4,5-f] 1,10-phenanthroline, is incorporated into a polystyrene matrix of polystyrene (PS) to form microfibers membranes. The possibility of using the resulted composite microfibrous membranes as an optical oxygen sensor is explored. Good linearity and short response time are obtained with a sensitivity of 9.8. These results suggest that phosphorescent [Cu(POP)(ECI-Phen)]BF 4 is a promising candidate for oxygen-sensors and PS is an excellent matrix for oxygen sensing material because it owns a large surface-area-to-volume ratio and can supply a homogeneous matrix for probe molecules. Further analysis suggests that the molecular structure of diamine ligand in Cu(I) complexes is critical for sensitivity due to the characteristic electronic structure of excited state Cu(I) complexes. - Highlights: → Cu(I) complex is incorporated into polystyrene matrix to form nanofibers. → Resulted sample exhibit good linearity and short response time. → PS is an excellent matrix for oxygen sensing material for probe molecules. → Molecular structure of diamine ligand is critical for sensitivity.

Measuring Distributional Inequality: Relative Body Mass Index Distributions by Gender, Race/Ethnicity, and Education, United States (1999–2006

Directory of Open Access Journals (Sweden)

Brian C. Houle

2010-01-01

Full Text Available Few studies consider obesity inequalities as a distributional property. This study uses relative distribution methods to explore inequalities in body mass index (BMI; kg/m2. Data from 1999–2006 from the National Health and Nutrition Examination Survey were used to compare BMI distributions by gender, Black/White race, and education subgroups in the United States. For men, comparisons between Whites and Blacks show a polarized relative distribution, with more Black men at increased risk of over or underweight. Comparisons by education (overall and within race/ethnic groups effects also show a polarized relative distribution, with more cases of the least educated men at the upper and lower tails of the BMI distribution. For women, Blacks have a greater probability of high BMI values largely due to a right-shifted BMI distribution relative to White women. Women with less education also have a BMI distribution shifted to the right compared to the most educated women.

Polystyrene/magnesium hydroxide nanocomposite particles prepared by surface-initiated in-situ polymerization

International Nuclear Information System (INIS)

Liu Hui; Yi Jianhong

2009-01-01

In order to avoid their agglomeration and incompatibility with hydrophobic polystyrene substrate, magnesium hydroxide nanoparticles were encapsulated by surface-initiated in-situ polymerization of styrene. The process contained two steps: electrostatic adsorption of initiator and polymerization of monomer on the surface of magnesium hydroxide. It was found that high adsorption ratio in the electrostatic adsorption of initiator could be attained only in acidic region, and the adsorption belonged to typical physical process. Compared to traditional in-situ polymerization, higher grafting ratio was obtained in surface-initiated in-situ polymerization, which can be attributed to weaker steric hindrance. Both Fourier transform infrared spectroscopy (FTIR) and transmission electron microscopy (TEM) indicated that polystyrene/magnesium hydroxide nanocomposite particles had been successfully prepared by surface-initiated in-situ polymerization. The resulting samples were also analyzed and characterized by means of contact angle testing, dispersibility evaluation and thermogravimetric analysis

The impact of mass transfer limitations on size distributions of particle associated SVOCs in outdoor and indoor environments

Energy Technology Data Exchange (ETDEWEB)

Liu, Cong; Zhang, Yinping [Department of Building Science, Tsinghua University, Beijing (China); Weschler, Charles J., E-mail: weschlch@rwjms.rutgers.edu [Department of Building Science, Tsinghua University, Beijing (China); Environmental and Occupational Health Sciences Institute, Rutgers University, Piscataway, NJ (United States); International Center for Indoor Environment and Energy, Technical University of Denmark, Lyngby (Denmark)

2014-11-01

Semi-volatile organic compounds (SVOCs) partition between the gas phase and airborne particles. The size distribution of particle-associated SVOCs impacts their fate in outdoor and indoor environments, as well as human exposure to these compounds and subsequent health risks. Allen et al. (1996) previously proposed that the rate of mass transfer can impact polycyclic aromatic hydrocarbon (PAH) partitioning among different sized particles, especially for time scales relevant to urban aerosols. The present study quantitatively builds on this idea, presenting a model that incorporates dynamic SVOC/particle interaction and applying this model to typical outdoor and indoor scenarios. The model indicates that the impact of mass transfer limitations on the size distribution of a particle-associated SVOC can be evaluated by the ratio of the time to achieve gas–particle equilibrium relative to the residence time of particles. The higher this ratio, the greater the influence of mass transfer limitations on the size distribution of particle-associated SVOCs. The influence of such constraints is largest on the fraction of particle-associated SVOCs in the coarse mode (> 2 μm). Predictions from the model have been found to be in reasonable agreement with size distributions measured for PAHs at roadside and suburban locations in Japan. The model also quantitatively explains shifts in the size distributions of particle associated SVOCs compared to those for particle mass, and the manner in which these shifts vary with temperature and an SVOC's molecular weight. - Highlights: • Rate of mass transfer can impact SVOC partitioning among different sized particles. • Model was developed that incorporates dynamic SVOC/particle sorption. • Key parameters: mass-transfer coefficients, partition coefficient, residence time • Model explains observed SVOC size distribution shifts with temperature and MW. • Largest impact of mass transfer constraints: SVOC sorption to coarse

Water mass distributions and transports for the 2014 GEOVIDE cruise in the North Atlantic

Science.gov (United States)

García-Ibáñez, Maribel I.; Pérez, Fiz F.; Lherminier, Pascale; Zunino, Patricia; Mercier, Herlé; Tréguer, Paul

2018-04-01

We present the distribution of water masses along the GEOTRACES-GA01 section during the GEOVIDE cruise, which crossed the subpolar North Atlantic Ocean and the Labrador Sea in the summer of 2014. The water mass structure resulting from an extended optimum multiparameter (eOMP) analysis provides the framework for interpreting the observed distributions of trace elements and their isotopes. Central Waters and Subpolar Mode Waters (SPMW) dominated the upper part of the GEOTRACES-GA01 section. At intermediate depths, the dominant water mass was Labrador Sea Water, while the deep parts of the section were filled by Iceland-Scotland Overflow Water (ISOW) and North-East Atlantic Deep Water. We also evaluate the water mass volume transports across the 2014 OVIDE line (Portugal to Greenland section) by combining the water mass fractions resulting from the eOMP analysis with the absolute geostrophic velocity field estimated through a box inverse model. This allowed us to assess the relative contribution of each water mass to the transport across the section. Finally, we discuss the changes in the distribution and transport of water masses between the 2014 OVIDE line and the 2002-2010 mean state. At the upper and intermediate water levels, colder end-members of the water masses replaced the warmer ones in 2014 with respect to 2002-2010, in agreement with the long-term cooling of the North Atlantic Subpolar Gyre that started in the mid-2000s. Below 2000 dbar, ISOW increased its contribution in 2014 with respect to 2002-2010, with the increase being consistent with other estimates of ISOW transports along 58-59° N. We also observed an increase in SPMW in the East Greenland Irminger Current in 2014 with respect to 2002-2010, which supports the recent deep convection events in the Irminger Sea. From the assessment of the relative water mass contribution to the Atlantic Meridional Overturning Circulation (AMOC) across the OVIDE line, we conclude that the larger AMOC intensity in

Water-stable diblock polystyrene-block-poly(2-vinyl pyridine) and diblock polystyrene-block-poly(methyl methacrylate) cylindrical patterned surfaces inhibit settlement of zoospores of the green alga Ulva.

Science.gov (United States)

Grozea, Claudia M; Gunari, Nikhil; Finlay, John A; Grozea, Daniel; Callow, Maureen E; Callow, James A; Lu, Zheng-Hong; Walker, Gilbert C

2009-04-13

Nanopatterned surfaces with hydrophobic and hydrophilic domains were produced using the diblock copolymer polystyrene-block-poly(2-vinyl pyridine) (PS-b-P2VP) and polystyrene-block-poly(methyl methacrylate) (PS-b-PMMA). The PS-b-P2VP diblock copolymer, mixed with the cross-linker benzophenone and spin-coated onto silicon wafers, showed self-assembled cylindrical structures, which were retained after UV treatment for cross-linking. The thin films displayed cylindrical domains after immersion in water. This study shows that pattern retention in water is possible for a long period of time, at least for two weeks in pure water and three weeks in artificial seawater. The PS-b-PMMA diblock showed self-assembled cylindrical structures. PS-b-P2VP and PS-b-PMMA cylindrical patterned surfaces showed reduced settlement of zoospores of the green alga Ulva compared to unpatterned surfaces. The copolymers were investigated using atomic force microscopy and X-ray photoelectron spectroscopy.

Conversion of waste polystyrene through catalytic degradation into valuable products

Energy Technology Data Exchange (ETDEWEB)

Shah, Jasmin; Jan, Muhammad Rasul; Adnan [University of Peshawar, Peshawar (Pakistan)

2014-08-15

Waste expanded polystyrene (EPS) represents a source of valuable chemical products like styrene and other aromatics. The catalytic degradation was carried out in a batch reactor with a mixture of polystyrene (PS) and catalyst at 450 .deg. C for 30 min in case of Mg and at 400 .deg. C for 2 h both for MgO and MgCO{sub 3} catalysts. At optimum degradation conditions, EPS was degraded into 82.20±3.80 wt%, 91.60±0.20 wt% and 81.80±0.53 wt% liquid with Mg, MgO and MgCO{sub 3} catalysts, respectively. The liquid products obtained were separated into different fractions by fractional distillation. The liquid fractions obtained with three catalysts were compared, and characterized using GC-MS. Maximum conversion of EPS into styrene monomer (66.6 wt%) was achieved with Mg catalyst, and an increase in selectivity of compounds was also observed. The major fraction at 145 .deg. C showed the properties of styrene monomer. The results showed that among the catalysts used, Mg was found to be the most effective catalyst for selective conversion into styrene monomer as value added product.

Increased adsorption of histidine-tagged proteins onto tissue culture polystyrene.

Science.gov (United States)

Holmberg, Maria; Hansen, Thomas Steen; Lind, Johan Ulrik; Hjortø, Gertrud Malene

2012-04-01

In this study we compare histidine-tagged and native proteins with regards to adsorption properties. We observe significantly increased adsorption of proteins with an incorporated polyhistidine amino acid motif (HIS-tag) onto tissue culture polystyrene (TCPS) compared to similar proteins without a HIS-tag. The effect is not observed on polystyrene (PS). Adsorption experiments have been performed at physiological pH (7.4) and the effect was only observed for the investigated proteins that have pI values below or around 7.4. Competitive adsorption experiments with imidazole and ethylenediaminetetraacetic acid (EDTA), as well as adsorption performed at different pH and ionic strength indicates that the high adsorption is caused by electrostatic interaction between negatively charged carboxylate groups on the TCPS surface and positively charged histidine residues in the proteins. Pre-adsorption of bovine serum albumin (BSA) does not decrease the adsorption of HIS-tagged proteins onto TCPS. Our findings identify a potential problem in using HIS-tagged signalling molecule in assays with cells cultured on TCPS, since the concentration of the molecule in solution might be affected and this could critically influence the assay outcome. Copyright © 2011 Elsevier B.V. All rights reserved.

3D-HST+CANDELS: The Evolution of the Galaxy Size-Mass Distribution since z = 3

Science.gov (United States)

van der Wel, A.; Franx, M.; van Dokkum, P. G.; Skelton, R. E.; Momcheva, I. G.; Whitaker, K. E.; Brammer, G. B.; Bell, E. F.; Rix, H.-W.; Wuyts, S.; Ferguson, H. C.; Holden, B. P.; Barro, G.; Koekemoer, A. M.; Chang, Yu-Yen; McGrath, E. J.; Häussler, B.; Dekel, A.; Behroozi, P.; Fumagalli, M.; Leja, J.; Lundgren, B. F.; Maseda, M. V.; Nelson, E. J.; Wake, D. A.; Patel, S. G.; Labbé, I.; Faber, S. M.; Grogin, N. A.; Kocevski, D. D.

2014-06-01

Spectroscopic+photometric redshifts, stellar mass estimates, and rest-frame colors from the 3D-HST survey are combined with structural parameter measurements from CANDELS imaging to determine the galaxy size-mass distribution over the redshift range 0 3 × 109 M ⊙, and steep, R_{eff}\\propto M_*^{0.75}, for early-type galaxies with stellar mass >2 × 1010 M ⊙. The intrinsic scatter is lsim0.2 dex for all galaxy types and redshifts. For late-type galaxies, the logarithmic size distribution is not symmetric but is skewed toward small sizes: at all redshifts and masses, a tail of small late-type galaxies exists that overlaps in size with the early-type galaxy population. The number density of massive (~1011 M ⊙), compact (R eff < 2 kpc) early-type galaxies increases from z = 3 to z = 1.5-2 and then strongly decreases at later cosmic times.

Applications for skimmer coupling systems, combining simultaneous thermal analysers with mass spectrometers

International Nuclear Information System (INIS)

Kaisersberger, E.; Post, E.

1998-01-01

The sensitivity of the Skimmer coupling for combining the simultaneous thermal analysis (STA) method TG-DTA/DSC and mass spectrometry (MS) is further improved by a factor of three using an automatic vacuum control device. Especially high mass numbers are detected without the common condensation problems met in capillary couplings, as is shown by application of the skimmer coupling for coal, CuGaSe 2 -semiconductor material and polystyrene. The basic idea of the novel pulse thermal analysis technique (PTA) is demonstrated. (Copyright (c) 1998 Elsevier Science B.V., Amsterdam. All rights reserved.)

Rapid and low-cost fabrication of polystyrene-based molds for PDMS microfluidic devices using a CO2 laser

KAUST Repository

Li, Huawei; Fan, Yiqiang; Foulds, Ian G.

2011-01-01

In this article, we described a rapid and low-cost method to fabricate polystyrene molds for PDMS microfluidic devices using a CO2 laser system. It takes only several minutes to fabricate the polystyrene mold with bump pattern on top of it using a CO2 laser system. The bump pattern can be easily transferred to PDMS and fabricate microchannles as deep as 3μm on PDMS. © (2012) Trans Tech Publications, Switzerland.

Rapid and low-cost fabrication of polystyrene-based molds for PDMS microfluidic devices using a CO2 laser

KAUST Repository

Li, Huawei

2011-11-01

In this article, we described a rapid and low-cost method to fabricate polystyrene molds for PDMS microfluidic devices using a CO2 laser system. It takes only several minutes to fabricate the polystyrene mold with bump pattern on top of it using a CO2 laser system. The bump pattern can be easily transferred to PDMS and fabricate microchannles as deep as 3μm on PDMS. © (2012) Trans Tech Publications, Switzerland.

Performance ratio hardness characteristics polystyrene-metal composite materials

International Nuclear Information System (INIS)

Klepikov, V.F.; Prokhorenko, E.M.; Lytvynenko, V.V.; Zakharchenko, A.A.; Hazhmuradov, M.A.

2015-01-01

The methods of measuring the hardness of layered polystyrene-metallic composite materials. It is proposed to use powder-like tungsten and powder-like steel as radiation-protective layer. A measurement of the hardness of composites of different composition, and given its dependence on the particle size and their form. The possibility of increasing the hardness of the composites reinforced with metallic additives. Radiation-protective characteristics were calculated for the studied species of composite materials. Influence of the quantitative composition of the metal components is studied on the change of the absorbed dose of gamma radiation

Melt dispersion of thermoplastic polystyrene in polymer polyols

OpenAIRE

2009-01-01

Polystyrene is dispersed into a polyol via a mechanical dispersion process. A stabilizer is present to stabilize the dispersed polymer particles. The stabilizer includes a copolymer of (1) from 10 to 70% by weight of a branched polyol which has a molecular weight of from 4000 to 20,000, from 0.2 to about 1.2 polymerizable ethylenically unsaturated groups per molecule and from about 3 to about 8 hydroxyl groups per molecule with (2) from 30 to 90% by weight of styrene or a mixture of styrene a...

Pre-Hawking radiation may allow for reconstruction of the mass distribution of the collapsing object

Energy Technology Data Exchange (ETDEWEB)

Dai, De-Chang, E-mail: diedachung@gmail.com [Institute of Natural Sciences, Shanghai Key Lab for Particle Physics and Cosmology, and Center for Astrophysics and Astronomy, Department of Physics and Astronomy, Shanghai Jiao Tong University, Shanghai 200240 (China); Stojkovic, Dejan [HEPCOS, Department of Physics, SUNY, University at Buffalo, Buffalo, NY 14260-1500 (United States)

2016-07-10

Hawking radiation explicitly depends only on the black hole's total mass, charge and angular momentum. It is therefore generally believed that one cannot reconstruct the information about the initial mass distribution of an object that made the black hole. However, instead of looking at radiation from a static black hole, we can study the whole time-dependent process of the gravitational collapse, and pre-Hawking radiation which is excited because of the time-dependent metric. We compare radiation emitted by a single collapsing shell with that emitted by two concentric shells of the equivalent total mass. We calculate the gravitational trajectory and the momentum energy tensor. We show that the flux of energy emitted during the collapse by a single shell is significantly different from the flux emitted by two concentric shells of the equivalent total mass. When the static black hole is formed, the fluxes become indistinguishable. This implies that an observer studying the flux of particles from a collapsing object could in principle reconstruct information not only about the total mass of the collapsing object, but also about the mass distribution.

Pre-Hawking radiation may allow for reconstruction of the mass distribution of the collapsing object

Directory of Open Access Journals (Sweden)

De-Chang Dai

2016-07-01

Full Text Available Hawking radiation explicitly depends only on the black hole's total mass, charge and angular momentum. It is therefore generally believed that one cannot reconstruct the information about the initial mass distribution of an object that made the black hole. However, instead of looking at radiation from a static black hole, we can study the whole time-dependent process of the gravitational collapse, and pre-Hawking radiation which is excited because of the time-dependent metric. We compare radiation emitted by a single collapsing shell with that emitted by two concentric shells of the equivalent total mass. We calculate the gravitational trajectory and the momentum energy tensor. We show that the flux of energy emitted during the collapse by a single shell is significantly different from the flux emitted by two concentric shells of the equivalent total mass. When the static black hole is formed, the fluxes become indistinguishable. This implies that an observer studying the flux of particles from a collapsing object could in principle reconstruct information not only about the total mass of the collapsing object, but also about the mass distribution.

A model for the stress-strain behavior of toughened polystyrene. Part 2

NARCIS (Netherlands)

Sjoerdsma, S.D.; Heikens, D.

1982-01-01

The general stress-strain relationship derived in an earlier paper is applied to analyse experimental stress-strain curves of polystyrene-polyethylene blends. It is concluded from the stress and temperature dependence of the rates of craze initiation and craze growth that these rates can be

Ordering of Polystyrene Nanoparticles on Substrates Pre-Coated with Different Polyelectrolyte Architectures

Directory of Open Access Journals (Sweden)

Matthias Karg

2013-06-01

Full Text Available Adjusting the inter-particle distances in ordered nanoparticle arrays can create new nano-devices and is of increasing importance to a number of applications such as nanoelectronics and optical devices. The assembly of negatively charged polystyrene (PS nanoparticles (NPs on Poly(2-(dimethylaminoethyl methacrylate (PDMAEMA brushes, quaternized PDMAEMA brushes and Si/PEI/(PSS/PAH2, was studied using dip- and spin-coating techniques. By dip-coating, two dimensional (2-D, randomly distributed non-close packed particle arrays were assembled on Si/PEI/(PSS/PAH2 and PDMAEMA brushes. The inter-particle repulsion leads to lateral mobility of the particles on these surfaces. The 200 nm diameter PS NPs tended to an inter-particle distance of 350 to 400 nm (center to center. On quaternized PDMAEMA brushes, the strong attractive interaction between the NPs and the brush dominated, leading to clustering of the particles on the brush surface. Particle deposition using spin-coating at low spin rates resulted in hexagonal close-packed multilayer structures on Si/PEI/(PSS/PAH2. Close-packed assemblies with more pronounced defects are also observed on PDMAEMA brushes and QPDMAEMA brushes. In contrast, randomly distributed monolayer NP arrays were achieved at higher spin rates on all polyelectrolyte architectures. The area fraction of the particles decreased with increasing spin rate.

Application of “Boomerang” Linear Polystyrene-Stabilized Pd Nanoparticles to a Series of C-C Coupling Reactions in Water

Directory of Open Access Journals (Sweden)

Atsushi Ohtaka

2015-02-01

Full Text Available The application of a catch-and-release system for soluble Pd species between water (reaction medium and polystyrene (polymer support was examined in the Suzuki coupling reaction with 2-bromothiophene and the Heck reaction with styrene or bromobenzene. Although a slight increase in particle size was observed by TEM after re-stabilization of the Pd species on linear polystyrene, no agglomeration was observed.

Subchannel measurements of the equilibrium quality and mass flux distribution in a rod bundle

International Nuclear Information System (INIS)

Lahey, R.T. Jr.

1986-01-01

An experiment was performed to measure the equilibrium subchannel void and mass flux distribution in a simulated BWR rod bundle. These new equilibrium subchannel data are unique and represent an excellent basis for subchannel ''void drift'' model development and assessment. Equilibrium subchannel void and mass flux distributions have been determined from the data presented herein. While the form of these correlations agree with the results of previous theoretical investigations, they should be generalized with caution since the current data base has been taken at only one (low) system pressure. Clearly there is a need for equilibrium subchannel data at higher system pressures if mechanistic subchannel models are to be developed

Non-conductive ferromagnetic carbon-coated (Co, Ni) metal/polystyrene nanocomposites films

Energy Technology Data Exchange (ETDEWEB)

Takacs, H., E-mail: helene.takacs@gmail.com [CEA, LETI, MINATEC Campus, Grenoble 38054 (France); LTM-CNRS-UJF, CEA, LETI, Minatec Campus, Grenoble 38054 (France); Viala, B.; Hermán, V. [CEA, LETI, MINATEC Campus, Grenoble 38054 (France); Tortai, J.-H. [LTM-CNRS-UJF, CEA, LETI, Minatec Campus, Grenoble 38054 (France); Duclairoir, F. [Université Grenoble Alpes, INAC, Grenoble 38054 (France); CEA, INAC, Grenoble 38054 (France)

2016-03-07

This article reports non-conductive ferromagnetic properties of metal/polymer nanocomposite films intended to be used for RF applications. The nanocomposite arrangement is unique showing a core double-shell structure of metal-carbon-polystyrene: M/C//P{sub 1}/P{sub 2}, where M = Co, Ni is the core material, C = graphene or carbon is the first shell acting as a protective layer against oxidation, P{sub 1} = pyrene-terminated polystyrene is the second shell for electrical insulation, and P{sub 2} = polystyrene is a supporting matrix (// indicates actual grafting). The nanocomposite formulation is briefly described, and the film deposition by spin-coating is detailed. Original spin-curves are reported and analyzed. One key outcome is the achievement of uniform and cohesive films at the wafer scale. Structural properties of films are thoroughly detailed, and weight and volume fractions of M/C are considered. Then, a comprehensive overview of DC magnetic and electrical properties is reported. A discussion follows on the magnetic softness of the nanocomposites vs. that of a single particle (theoretical) and the raw powder (experimental). Finally, unprecedented achievement of high magnetization (∼0.6 T) and ultra-high resistivity (∼10{sup 10 }μΩ cm) is shown. High magnetization comes from the preservation of the existing protective shell C, with no significant degradation on the particle net-moment, and high electrical insulation is ensured by adequate grafting of the secondary shell P{sub 1}. To conclude, the metal/polymer nanocomposites are situated in the landscape of soft ferromagnetic materials for RF applications (i.e., inductors and antennas), by means of two phase-diagrams, where they play a crucial role.

Microbial degradation of high impact polystyrene (HIPS), an e-plastic with decabromodiphenyl oxide and antimony trioxide

International Nuclear Information System (INIS)

Sekhar, Vini C.; Nampoothiri, K. Madhavan; Mohan, Arya J.; Nair, Nimisha R.; Bhaskar, Thallada; Pandey, Ashok

2016-01-01

Highlights: • Biodegradation of a high impact polystyrene e − plastic. • 12.4% (w/w) e plastic film lost using an isolate, Enterobacter sp. • Noted changes in the physico-chemical characteristics of degraded e-plastic film. • Polystyrene intermediates were detected in the degradation medium. • e-plastic degrading microbes displayed extracellular depolymerase activity. - Abstract: Accumulation of electronic waste has increased catastrophically and out of that various plastic resins constitute one of the leading thrown out materials in the electronic machinery. Enrichment medium, containing high impact polystyrene (HIPS) with decabromodiphenyl oxide and antimony trioxide as sole carbon source, was used to isolate microbial cultures. The viability of these cultures in the e-plastic containing mineral medium was further confirmed by triphenyl tetrazolium chloride (TTC) reduction test. Four cultures were identified by 16S rRNA sequencing as Enterobacter sp., Citrobacter sedlakii, Alcaligenes sp. and Brevundimonas diminuta. Biodegradation experiments were carried out in flask level and gelatin supplementation (0.1% w/v) along with HIPS had increased the degradation rate to a maximum of 12.4% (w/w) within 30 days. This is the first report for this kind of material. The comparison of FTIR, NMR, and TGA analysis of original and degraded e-plastic films revealed structural changes under microbial treatment. Polystyrene degradation intermediates in the culture supernatant were also detected using HPLC analysis. The gravity of biodegradation was validated by morphological changes under scanning electron microscope. All isolates displayed depolymerase activity to substantiate enzymatic degradation of e-plastic.

Microbial degradation of high impact polystyrene (HIPS), an e-plastic with decabromodiphenyl oxide and antimony trioxide

Energy Technology Data Exchange (ETDEWEB)

Sekhar, Vini C. [Biotechnology Division, CSIR-National Institute for Interdisciplinary Science and Technology (NIIST), Trivandrum 695 019, Kerala (India); Nampoothiri, K. Madhavan, E-mail: madhavan85@hotmail.com [Biotechnology Division, CSIR-National Institute for Interdisciplinary Science and Technology (NIIST), Trivandrum 695 019, Kerala (India); Mohan, Arya J.; Nair, Nimisha R. [Biotechnology Division, CSIR-National Institute for Interdisciplinary Science and Technology (NIIST), Trivandrum 695 019, Kerala (India); Bhaskar, Thallada [Bio-Fuels Division (BFD), CSIR-Indian Institute of Petroleum (IIP), Dehradun, Uttarakhand 248005 (India); Pandey, Ashok [Biotechnology Division, CSIR-National Institute for Interdisciplinary Science and Technology (NIIST), Trivandrum 695 019, Kerala (India)

2016-11-15

Highlights: • Biodegradation of a high impact polystyrene e − plastic. • 12.4% (w/w) e plastic film lost using an isolate, Enterobacter sp. • Noted changes in the physico-chemical characteristics of degraded e-plastic film. • Polystyrene intermediates were detected in the degradation medium. • e-plastic degrading microbes displayed extracellular depolymerase activity. - Abstract: Accumulation of electronic waste has increased catastrophically and out of that various plastic resins constitute one of the leading thrown out materials in the electronic machinery. Enrichment medium, containing high impact polystyrene (HIPS) with decabromodiphenyl oxide and antimony trioxide as sole carbon source, was used to isolate microbial cultures. The viability of these cultures in the e-plastic containing mineral medium was further confirmed by triphenyl tetrazolium chloride (TTC) reduction test. Four cultures were identified by 16S rRNA sequencing as Enterobacter sp., Citrobacter sedlakii, Alcaligenes sp. and Brevundimonas diminuta. Biodegradation experiments were carried out in flask level and gelatin supplementation (0.1% w/v) along with HIPS had increased the degradation rate to a maximum of 12.4% (w/w) within 30 days. This is the first report for this kind of material. The comparison of FTIR, NMR, and TGA analysis of original and degraded e-plastic films revealed structural changes under microbial treatment. Polystyrene degradation intermediates in the culture supernatant were also detected using HPLC analysis. The gravity of biodegradation was validated by morphological changes under scanning electron microscope. All isolates displayed depolymerase activity to substantiate enzymatic degradation of e-plastic.

Avaliação das propriedades de misturas de poliestireno com oligômeros de poli(Óxido de Propileno e poliestireno Property relationships in blends based on polystyrene

Directory of Open Access Journals (Sweden)

Maria Andréa P. R. Torres

1998-01-01

Full Text Available Misturas poliméricas de poliestireno (PS1 com poli(óxido de propileno (PPO e de poliestireno (PS1 com poliestireno de baixíssima massa molecular (PS2, foram preparadas, em diversas composições, para avaliação das propriedades térmicas, mecânicas e de escoamento. As propriedades térmicas foram avaliadas por calorimetria diferencial de varredura (DSC e as propriedades mecânicas e de escoamento foram determinadas através de ensaios de tração e monitoração do valor do torque durante o processamento das misturas, respectivamente. Foi observado que o PPO atua como plastificante do poliestireno enquanto que o PS2 não apresenta este comportamento. Entretanto, a adição de ambos os componentes produz mudança no empacotamento molecular, originando o aparecimento de fissuras na superfície dos materiais.Poly(propylene oxide (PPO and polystyrene of lower molecular weight were added to commercial polystyrene. These blends were prepared in a Haake internal mixer and the properties of polystyrene/poly(propylene oxide and polystyrene/polystyrene of lower molecular weight blends were evaluated using tensile testing, differential scanning calorimetry and torque curves obtained during the process. The results obtained show that PPO acts as a plasticizer for polystyrene, decreasing significantly its torque value and the glass transition temperature. The addition of polystyrene of lower molecular weight to polystyrene causes subtle modifications. However, the addition of both PPO and polystyrene of lower molecular weight to polystyrene probably accelerates crazes formation and it is usually detrimental to the mechanical properties.

Mass exchange and angular distribution in a dynamical treatment of heavy ion collisions

International Nuclear Information System (INIS)

Ngo, C.; Hofmann, H.

1977-01-01

One presents a first numerical computation of the absolute value of the double differential cross section as a function of mass asymmetry and detection angle including a dynamical coupling between relative motion and mass asymmetry. One applies it to the 63 Cu+ 197 Au experiment at two different energies. The equation of motion used is a Fokker-Planck equation for distribution function in classical phase space. The coefficients needed are those known from classical model calculations, besides a friction coefficient introduced for the mass asymmetry degree. Encouraging agreement between the calculated and experimental curves is found

B10(n,α)Li7 irradiation effects on high impact polystyrene

International Nuclear Information System (INIS)

Gupta, M.C.; Bansod, V.P.

1984-01-01

Irradiation effects of B 10 (n,α)Li 7 charged particles on high impact polystyrene were compared with those of Co 60 γ-rays, from the viewpoint of linear energy transfer (LET). For irradiation in air, the G values of crosslinks and main-chain scissions, G(X) and G(S) are 0.018 and 0.06, respectively, for γ-rays of low LET (ca. 0.22 eV/nm). Charged particles [B 10 (n,α)Li 7 ] of high LET (ca. 280 eV/nm) increase the G(X) value to 0.15 but G(S) is not much affected. All these findings are explained qualitatively by a difference in the distribution of energy deposition and the mechanism involving the competition between the deactivation of an excited molecule by the collision with ground state molecules and the macroradical formation by the bimolecular reaction of the excited molecules. These excited molecules in HIPS might be produced more closely to one another by charged particles than by γ-rays. (author)

Study of the solubility and stability of polystyrene wastes in a dissolution recycling process

International Nuclear Information System (INIS)

Garcia, Maria Teresa; Gracia, Ignacio; Duque, Gema; Lucas, Antonio de; Rodriguez, Juan Francisco

2009-01-01

Dissolution with suitable solvents is one of the cheapest and more efficient processes for polystyrene waste management. In this work the solubility of polystyrene foams in several solvents benzene, toluene, xylene, tetrahydrofuran, chloroform, 1,3-butanediol, 2-butanol, linalool, geraniol, d-limonene, p-cymene, terpinene, phellandrene, terpineol, menthol, eucalyptol, cinnamaldheyde, nitrobenzene, N,N-dimethylformamide and water has been determined. Experimental results have shown that to develop a 'green process' the constituents of essential oils, d-limonene, p-cymene, terpinene, phellandrene, are the most appropriate solvents. The action of these solvent does not produce any degradation of polymer chains. The solubility of the polymer in the mentioned solvents at different temperatures has been investigated. The solvent can be easily recycled by distillation.

The Study of Prompt and Delayed Muon Induced Fission. I.Total kinetic energies and mass distributions

NARCIS (Netherlands)

David, P; Hartfiel, J.; Janszen, H.; Petitjean, C.; Reist, H.W.; Polikanov, S.M.; Konijn, J.; Laat, de C.T.A.M.; Taal, A.; Krogulski, T.; Johansson, T.; Tibell, G.; Achard van Enschut, d' J.F.M.

1987-01-01

Mass yield and total kinetic energy release (TKE) distributions of fragments from prompt and delayed muon induced fission, separately, have been measured for the isotopes235U,238U,237Np and242Pu. The distributions from prompt muon induced fission are compared with the corresponding distributions

The β Pictoris association low-mass members: Membership assessment, rotation period distribution, and dependence on multiplicity

Science.gov (United States)

Messina, S.; Lanzafame, A. C.; Malo, L.; Desidera, S.; Buccino, A.; Zhang, L.; Artemenko, S.; Millward, M.; Hambsch, F.-J.

2017-10-01

Context. Low-mass members of young loose stellar associations and open clusters exhibit a wide spread of rotation periods. Such a spread originates from the distributions of masses and initial rotation periods. However, multiplicity can also play a significant role. Aims: We aim to investigate the role played by physical companions in multiple systems in shortening the primordial disk lifetime, anticipating the rotation spin up with respect to single stars. Methods: We have compiled the most extensive list to date of low-mass bona fide and candidate members of the young 25-Myr β Pictoris association. We have measured from our own photometric time series or from archival time series the rotation periods of almost all members. In a few cases the rotation periods were retrieved from the literature. We used updated UVWXYZ components to assess the membership of the whole stellar sample. Thanks to the known basic properties of most members we built the rotation period distribution distinguishing between bona fide members and candidate members and according to their multiplicity status. Results: We find that single stars and components of multiple systems in wide orbits (>80 AU) have rotation periods that exhibit a well defined sequence arising from mass distribution with some level of spread likely arising from initial rotation period distribution. All components of multiple systems in close orbits (Pleiades shows that whereas the evolution of F-G stars is well reproduced by angular momentum evolution models, this is not the case for the slow K and early-M stars. Finally, we find that the amplitude of their light curves is correlated neither with rotation nor with mass. Conclusions: Once single stars and wide components of multiple systems are separated from close components of multiple systems, the rotation period distributions exhibit a well defined dependence on mass that allows us to make a meaningful comparison with similar distributions of either younger or older

Measurement of the average mass of proteins adsorbed to a nanoparticle by using a suspended microchannel resonator.

Science.gov (United States)

Nejadnik, M Reza; Jiskoot, Wim

2015-02-01

We assessed the potential of a suspended microchannel resonator (SMR) to measure the adsorption of proteins to nanoparticles. Standard polystyrene beads suspended in buffer were weighed by a SMR system. Particle suspensions were mixed with solutions of bovine serum albumin (BSA) or monoclonal human antibody (IgG), incubated at room temperature for 3 h and weighed again with SMR. The difference in buoyant mass of the bare and protein-coated polystyrene beads was calculated into real mass of adsorbed proteins. The average surface area occupied per protein molecule was calculated, assuming a monolayer of adsorbed protein. In parallel, dynamic light scattering (DLS), nanoparticle tracking analysis (NTA), and zeta potential measurements were performed. SMR revealed a statistically significant increase in the mass of beads because of adsorption of proteins (for BSA and IgG), whereas DLS and NTA did not show a difference between the size of bare and protein-coated beads. The change in the zeta potential of the beads was also measurable. The surface area occupied per protein molecule was in line with their known size. Presented results show that SMR can be used to measure the mass of adsorbed protein to nanoparticles with a high precision in the presence of free protein. © 2014 Wiley Periodicals, Inc. and the American Pharmacists Association.

Boring crustaceans damage polystyrene floats under docks polluting marine waters with microplastic.

Science.gov (United States)

Davidson, Timothy M

2012-09-01

Boring isopods damage expanded polystyrene floats under docks and, in the process, expel copious numbers of microplastic particles. This paper describes the impacts of boring isopods in aquaculture facilities and docks, quantifies and discusses the implications of these microplastics, and tests if an alternate foam type prevents boring. Floats from aquaculture facilities and docks were heavily damaged by thousands of isopods and their burrows. Multiple sites in Asia, Australia, Panama, and the USA exhibited evidence of isopod damage. One isopod creates thousands of microplastic particles when excavating a burrow; colonies can expel millions of particles. Microplastics similar in size to these particles may facilitate the spread of non-native species or be ingested by organisms causing physical or toxicological harm. Extruded polystyrene inhibited boring, suggesting this foam may prevent damage in the field. These results reveal boring isopods cause widespread damage to docks and are a novel source of microplastic pollution. Copyright © 2012 Elsevier Ltd. All rights reserved.

The Influence of Methods Massed Practice and Distributed Practice Model on The Speed and Accuracy of Service Tennis Courts

Directory of Open Access Journals (Sweden)

Desak Wiwin,

2017-06-01

Full Text Available The purpose of this study was to analyze about (1 the effect of the method massed practice against the speed and accuracy of service, (2 the effect of the method of distributed practice against the speed and accuracy of service and (3 the influence of methods of massed practice and distributed practice against the speed and accuracy of service. This type of research used in this research is quantitative with quasiexperimental methods. The research design uses a non-randomized control group pretest posttest design, and data analysis using Manova. The process of data collection is done by testing the speed of service (dartfish and test accuracy (Hewitt during the pretest and posttest. The results of the study as follows: (1 there is a significant influence on the methods of massed practice to increase the speed and accuracy of service (2 there is a significant influence on the method of distributed practice to increase the speed and accuracy of service (3 There is no significant difference influence among methods massed ptactice practice and distributed to the speed and accuracy of service. Conclusions of this research is a method massed practice and distributed practice equally provide significant results but that gives the influence of better is method distributed practice to speed and accuracy of service.

Phase Segregation in Polystyrene?Polylactide Blends

Energy Technology Data Exchange (ETDEWEB)

Leung, Bonnie; Hitchcock, Adam; Brash, John; Scholl, Andreas; Doran, Andrew

2010-06-09

Spun-cast films of polystyrene (PS) blended with polylactide (PLA) were visualized and characterized using atomic force microscopy (AFM) and synchrotron-based X-ray photoemission electron microscopy (X-PEEM). The composition of the two polymers in these systems was determined by quantitative chemical analysis of near-edge X-ray absorption signals recorded with X-PEEM. The surface morphology depends on the ratio of the two components, the total polymer concentration, and the temperature of vacuum annealing. For most of the blends examined, PS is the continuous phase with PLA existing in discrete domains or segregated to the air?polymer interface. Phase segregation was improved with further annealing. A phase inversion occurred when films of a 40:60 PS:PLA blend (0.7 wt percent loading) were annealed above the glass transition temperature (Tg) of PLA.

Synthesis of Fluorophore-Doped Polystyrene Microspheres: Seed Material for Airflow Sensing.

Science.gov (United States)

Wohl, Christopher J; Kiefer, Jacob M; Petrosky, Brian J; Tiemsin, Pacita I; Lowe, K Todd; Maisto, Pietro M F; Danehy, Paul M

2015-09-23

Kiton red 620 (KR620) doped polystyrene latex microspheres (PSLs) were synthesized via soap-free emulsion polymerization to be utilized as a relatively nontoxic, fluorescent seed material for airflow characterization experiments. Poly(styrene-co-styrenesulfonate) was used as the PSL matrix to promote KR620 incorporation. Additionally, a bicarbonate buffer and poly(diallyldimethylammonium chloride), polyD, cationic polymer were added to the reaction solution to stabilize the pH and potentially influence the electrostatic interactions between the PSLs and dye molecules. A design of experiments (DOE) approach was used to efficiently investigate the variation of these materials. Using a 4-factor, 2-level response surface design with a center point, a series of experiments were performed to determine the dependence of these factors on particle diameter, diameter size distribution, fluorescent emission intensity, and KR620 retention. Using statistical analysis, the factors and factor interactions that most significantly affect the outputs were identified. These particles enabled velocity measurements to be made much closer to walls and surfaces than previously. Based on these results, KR620-doped PSLs may be utilized to simultaneously measure the velocity and mixing concentration, among other airflow parameters, in complex flows.

Water contentwater of determination of cationic polystyrene sulfonate resins by infrared spectrophotometry

International Nuclear Information System (INIS)

Noki, V.

1987-01-01

A method of the determination of water content in polystyrene sulfonate ion-exchange resins in the presence of alkaline earth counter-ions by I.R. spectrophotometry is proposed. This method does not hold in the case of transition metal due to the formation of coordinated complexes with water molecules.

Electrorheological Properties of Suspensions Prepared from Polystyrene- Block- Polyisoprene Copolymer

OpenAIRE

YAVUZ, Mustafa

2014-01-01

Considerable scientific and industrial interest is currently being focused on a class of materials known as electrorheological (ER) fluids, which display remarkable rheological behaviour, being able to convert rapidly and repeatedly from a liquid to solid when an electric field (E) is applied or removed. In this article, the synthesis, characterization, partial hydrolysis and ER properties of polystyrene- block}-polyisoprene copolymer (COP) were investigated. The block copolymer was ...

Relativistic Mechanics in Gravitational Fields Exterior to Rotating Homogeneous Mass Distributions within Spherical Geometry

Directory of Open Access Journals (Sweden)

Chifu E. N.

2009-07-01

Full Text Available General Relativistic metric tensors for gravitational fields exterior to homogeneous spherical mass distributions rotating with constant angular velocity about a fixed di- ameter are constructed. The coeffcients of affine connection for the gravitational field are used to derive equations of motion for test particles. The laws of conservation of energy and angular momentum are deduced using the generalized Lagrangian. The law of conservation of angular momentum is found to be equal to that in Schwarzschild’s gravitational field. The planetary equation of motion and the equation of motion for a photon in the vicinity of the rotating spherical mass distribution have rotational terms not found in Schwarzschild’s field.

Water mass distributions and transports for the 2014 GEOVIDE cruise in the North Atlantic

Directory of Open Access Journals (Sweden)

M. I. García-Ibáñez

2018-04-01

Full Text Available We present the distribution of water masses along the GEOTRACES-GA01 section during the GEOVIDE cruise, which crossed the subpolar North Atlantic Ocean and the Labrador Sea in the summer of 2014. The water mass structure resulting from an extended optimum multiparameter (eOMP analysis provides the framework for interpreting the observed distributions of trace elements and their isotopes. Central Waters and Subpolar Mode Waters (SPMW dominated the upper part of the GEOTRACES-GA01 section. At intermediate depths, the dominant water mass was Labrador Sea Water, while the deep parts of the section were filled by Iceland–Scotland Overflow Water (ISOW and North-East Atlantic Deep Water. We also evaluate the water mass volume transports across the 2014 OVIDE line (Portugal to Greenland section by combining the water mass fractions resulting from the eOMP analysis with the absolute geostrophic velocity field estimated through a box inverse model. This allowed us to assess the relative contribution of each water mass to the transport across the section. Finally, we discuss the changes in the distribution and transport of water masses between the 2014 OVIDE line and the 2002–2010 mean state. At the upper and intermediate water levels, colder end-members of the water masses replaced the warmer ones in 2014 with respect to 2002–2010, in agreement with the long-term cooling of the North Atlantic Subpolar Gyre that started in the mid-2000s. Below 2000 dbar, ISOW increased its contribution in 2014 with respect to 2002–2010, with the increase being consistent with other estimates of ISOW transports along 58–59° N. We also observed an increase in SPMW in the East Greenland Irminger Current in 2014 with respect to 2002–2010, which supports the recent deep convection events in the Irminger Sea. From the assessment of the relative water mass contribution to the Atlantic Meridional Overturning Circulation (AMOC across the OVIDE line, we conclude

Binding and orientation of fibronectin on polystyrene surfaces using immobilized bacterial adhesin-related peptides.

Science.gov (United States)

Klueh, U; Bryers, J D; Kreutzer, D L

2003-10-01

Fibronectin (FN) is known to bind to bacteria via high affinity receptors on bacterial surfaces known as adhesins. The binding of bacteria to FN is thought to have a key role in foreign device associated infections. For example, previous studies have indicated that Staphylococcus aureus adhesins bind to the 29 kDa NH(3) terminus end of FN, and thereby promote bacteria adherence to surfaces. Recently, the peptide sequences within the S. aureus adhesin molecule that are responsible for FN binding have been identified. Based on these observations, we hypothesize that functional FN can be bound and specifically oriented on polystyrene surfaces using bacterial adhesin-related (BRP-A) peptide. We further hypothesize that monoclonal antibodies that react with specific epitopes on the FN can be used to quantify both FN binding and orientation on these surfaces. Based on this hypothesis, we initiated a systematic investigation of the binding and orientation of FN on polystyrene surfaces using BRP-A peptide. To test this hypothesis, the binding and orientation of the FN to immobilized BRP-A was quantified using (125)I-FN, and monoclonal antibodies. (125)I-FN was used to quantitate FN binding to peptide-coated polystyrene surfaces. The orientation of bound FN was demonstrated by the use of monoclonal antibodies, which are reactive with the amine (N) or carboxyl (C) termini of the FN. The results of our studies demonstrated that when the BRP-A peptide was used to bind FN to surfaces that: 1. functional FN was bound to the peptide; 2. anti-C terminus antibodies bound to the peptide FN; and 3. only limited binding of anti-N terminus antibodies to peptide-bound FN occurred. We believe that the data that indicate an enhanced binding of anti-C antibodies reactive to anti-N antibodies are a result of the FN binding in an oriented manner with the N termini of FN bound tightly to the BRP-A on the polystyrene surface. Copyright 2003 Wiley Periodicals, Inc. J Biomed Mater Res 67A: 36

Liquid-liquid phase separation in dilute solutions of poly(styrene sulfonate) with multivalent cations: Phase diagrams, chain morphology, and impact of temperature

Science.gov (United States)

Hansch, Markus; Hämisch, Benjamin; Schweins, Ralf; Prévost, Sylvain; Huber, Klaus

2018-01-01

The dilute solution behavior of sodium poly(styrene sulfonate) is studied in the presence of trivalent Al3+ and bivalent Ba2+ cations at various levels of excess NaCl. The study evaluates the phase behavior and the morphology of the polyelectrolyte chains with increasing extent of decoration with the Al3+ and Ba2+ cations and analyses the effect of temperature on these decorated chains. The phase behavior is presented in the form of the cation concentration versus the respective poly(styrene sulfonate) concentration, recorded at the onset of precipitation. Whereas poly(styrene sulfonate) with Al3+ exhibits a linear phase boundary, denoted as the "threshold line," which increases with increasing poly(styrene sulfonate) concentration, Ba2+ cations show a threshold line which is independent of the poly(styrene sulfonate) concentration. An additional re-entrant phase, at considerably higher cation content than those of the threshold lines, is observed with Al3+ cations but not with Ba2+ cations. The threshold line and the re-entrant phase boundary form parts of the liquid-liquid phase boundary observed at the limit of low polymer concentration. The dimensions of the polyelectrolyte chains shrink considerably while approaching the respective threshold lines on increase of the Al3+ and Ba2+ cation content. However, subtle differences occur between the morphological transformation induced by Al3+ and Ba2+. Most strikingly, coils decorated with Al3+ respond very differently to temperature variations than coils decorated with Ba2+ do. As the temperature increases, the poly(styrene sulfonate) chains decrease their size in the presence of Al3+ cations but increase in size in the presence of Ba2+ cations.

ANALYSIS DEGRADATION OF POLYSTYRENE WITH MONTMORILLONITE NANOFILLERS

Directory of Open Access Journals (Sweden)

Maria Mihalikova

2014-01-01

Full Text Available The paper is focused on the experimental investigation of the montmorillonite nanofillers effect on deformation properties of polystyrene KRASTEN 171. In some cases, combination of a low amount of clay with dispersed polymeric phase may cause synergistic effects leading to very fair balance of mechanical behaviour. This seems to be a consequence of complex influencing the multiphase system by clay such as modification of components (reinforcement and parameters of the interface accompanied by influencing the dynamic phase behaviour, i.e., the compactibilizing effect. The paper analyses the effect of nanocomposites and type of the material on the individual measured parameters, relations between them, strength and deformation behaviour. Deformation was evaluated by non-contact videoextensometry method

Correlated dewetting patterns in thin polystyrene films

CERN Document Server

Neto, C; Seemann, R; Blossey, R; Becker, J; Grün, G

2003-01-01

We describe preliminary results of experiments and simulations concerned with the dewetting of thin polystyrene films (thickness < 7 nm) on top of silicon oxide wafers. In the experiments we scratched an initially flat film with an atomic force microscopy (AFM) tip, producing dry channels in the film. Dewetting of the films was imaged in situ using AFM and a correlated pattern of holes ('satellite holes') was observed along the rims bordering the channels. The development of this complex film rupture process was simulated and the results of experiments and simulations are in good agreement. On the basis of these results, we attempt to explain the appearance of satellite holes and their positions relative to pre-existing holes.

Correlated dewetting patterns in thin polystyrene films

International Nuclear Information System (INIS)

Neto, Chiara; Jacobs, Karin; Seemann, Ralf; Blossey, Ralf; Becker, Juergen; Gruen, Guenther

2003-01-01

We describe preliminary results of experiments and simulations concerned with the dewetting of thin polystyrene films (thickness < 7 nm) on top of silicon oxide wafers. In the experiments we scratched an initially flat film with an atomic force microscopy (AFM) tip, producing dry channels in the film. Dewetting of the films was imaged in situ using AFM and a correlated pattern of holes ('satellite holes') was observed along the rims bordering the channels. The development of this complex film rupture process was simulated and the results of experiments and simulations are in good agreement. On the basis of these results, we attempt to explain the appearance of satellite holes and their positions relative to pre-existing holes

Synthesis of Well-Defined Three-Arm Star-Branched Polystyrene through Arm-First Coupling Approach by Atom Transfer Radical Polymerization

OpenAIRE

Shahabuddin, Syed; Hamime Ismail, Fatem; Mohamad, Sharifah; Muhamad Sarih, Norazilawati

2015-01-01

Here we describe a simple route to synthesize three-arm star-branched polystyrene. Atom transfer radical polymerization technique has been utilized to yield branched polystyrene involving Williamson coupling strategy. Initially a linear polymeric chain of predetermined molecular weight has been synthesized which is further end-functionalized into a primary alkyl bromide moiety, a prime requisition for Williamson reaction. The end-functionalized polymer is then coupled using 1,1,1-tris(4-hydro...

Two-jet invariant-mass distribution at √s =1.8 TeV

International Nuclear Information System (INIS)

Abe, F.; Amidei, D.; Apollinari, G.; Ascoli, G.; Atac, M.; Auchincloss, P.; Baden, A.R.; Barbaro-Galtieri, A.; Barnes, V.E.; Bedeschi, F.; Behrends, S.; Belforte, S.; Bellettini, G.; Bellinger, J.; Bensinger, J.; Beretvas, A.; Berge, P.; Bertolucci, S.; Bhadra, S.; Binkley, M.; Blair, R.; Blocker, C.; Bofill, J.; Booth, A.W.; Brandenburg, G.; Brown, D.; Byon, A.; Byrum, K.L.; Campbell, M.; Carey, R.; Carithers, W.; Carlsmith, D.; Carroll, J.T.; Cashmore, R.; Cervelli, F.; Chadwick, K.; Chapin, T.; Chiarelli, G.; Chinowsky, W.; Cihangir, S.; Cline, D.; Connor, D.; Contreras, M.; Cooper, J.; Cordelli, M.; Curatolo, M.; Day, C.; DelFabbro, R.; Dell'Orso, M.; DeMortier, L.; Devlin, T.; DiBitonto, D.; Diebold, R.; Dittus, F.; DiVirgilio, A.; Elias, J.E.; Ely, R.; Errede, S.; Esposito, B.; Flaugher, B.; Focardi, E.; Foster, G.W.; Franklin, M.; Freeman, J.; Frisch, H.; Fukui, Y.; Garfinkel, A.F.; Giannetti, P.; Giokaris, N.; Giromini, P.; Gladney, L.; Gold, M.; Goulianos, K.; Grosso-Pilcher, C.; Haber, C.; Hahn, S.R.; Handler, R.; Harris, R.M.; Hauser, J.; Hessing, T.; Hollebeek, R.; Hu, P.; Hubbard, B.; Hurst, P.; Huth, J.; Jensen, H.; Johnson, R.P.; Joshi, U.; Kadel, R.W.; Kamon, T.; Kanda, S.; Kardelis, D.A.; Karliner, I.; Kearns, E.; Kephart, R.; Kesten, P.; Keutelian, H.; Kim, S.; Kirsch, L.; Kondo, K.; Kruse, U.; Kuhlmann, S.E.; Laasanen, A.T.; Li, W.; Liss, T.; Lockyer, N.; Marchetto, F.; Markeloff, R.; Markosky, L.A.; McIntyre, P.; Menzione, A.; Meyer, T.; Mikamo, S.; Miller, M.; Mimashi, T.; Miscetti, S.; Mishina, M.; Miyashita, S.; Mondal, N.; Mori, S.; Morita, Y.; Mukherjee, A.; Newman-Holmes, C.; Nodulman, L.; Paoletti, R.; Para, A.; Patrick, J.; Phillips, T.J.; Piekarz, H.; Plunkett, R.; Pondrom, L.; Proudfoot, J.; Punzi, G.; Quarrie, D.; Ragan, K.; Redlinger, G.; Rhoades, J.; Rimondi, F.; Ristori, L.; Rohaly, T.; Roodman, A.; Sansoni, A.; Sard, R.; Scarpine, V.; Schlabach, P.; Schmidt, E.E.; Schoessow, P.; Schub, M.H.; Schwitters, R.; Scribano, A.

1990-01-01

We present the dijet invariant-mass distribution in the region between 60 and 500 GeV, measured in 1.8-TeV bar pp collisions in the Collider Detector at Fermilab. Jets are restricted to the pseudorapidity interval |η| A A =Nα s M A /6, with N=5

Preparative-scale separation of C60 and C70 on polystyrene gel

International Nuclear Information System (INIS)

Guegel, A.; Becker, M.; Hammel, D.; Mindach, L.; Raeder, J.; Simon, T.; Wagner, M.; Muellen, K.

1992-01-01

Five grams of a mixture of C 60 /C 70 can be separated in 24 hours by gel permeation chromatography on polystyrene gel. The mobile phase can be completely recovered, and the method can be scaled up by a simple increase in the inner diameter of the column. (orig.) [de

Effects of the alkylamine functionalization of graphene oxide on the properties of polystyrene nanocomposites

Science.gov (United States)

Jang, Jinhee; Pham, Viet Hung; Rajagopalan, Balasubramaniyan; Hur, Seung Hyun; Chung, Jin Suk

2014-05-01

Alkylamine-functionalized graphene oxides (FGOs) have superior dispersibility in low-polar solvents and, as a result, they interact with low-polar polymers such as polystyrene. In this work, the functionalization of graphene oxide using three types of alkylamines, octylamine (OA), dodecylamine (DDA), and hexadecylamine (HDA), was performed, and nanocomposites of polystyrene (PS) and FGOs were prepared via solution blending. Different dispersions of FGOs over PS were obtained for the three alkylamines, and the properties of the PS composites were influenced by the length of the alkylamine. A better thermal stability was observed with a longer chain length of the alkylamine. On the other hand, functionalization with the shortest chain length alkylamine resulted in the highest increase in the storage modulus (3,640 MPa, 140%) at a 10 wt.% loading of FGO.

(Quasi-) 2D aggregation of polystyrene-b-dextran at the air-water interface

NARCIS (Netherlands)

Bosker, W.T.E.; Cohen Stuart, M.A.; Norde, W.

2013-01-01

Polystyrene-b-dextran (PS-b-Dextran) copolymers can be used to prepare dextran brushes at solid surfaces, applying Langmuir–Blodgett deposition. When recording the interfacial pressure versus area isotherms of a PS-b-Dextran monolayer, time-dependent hysteresis was observed upon compression and

(Quasi-) 2D Aggregation of Polystyrene-b-Dextran at the Air-Water Interface

NARCIS (Netherlands)

Bosker, Wouter T. E.; Stuart, Martien A. Cohen; Norde, Willem

2013-01-01

Polystyrene-b-dextran (PS-b-Dextran) copolymers can be used to prepare dextran brushes at solid surfaces, applying Langmuir Blodgett deposition. When recording the interfacial pressure versus area isotherms of a PS-b-Dextran monolayer, time-dependent hysteresis was observed upon compression and

Mechanical properties and local mobility of atactic-polystyrene films under constant-shear deformation

NARCIS (Netherlands)

Hudzinskyy, D.; Michels, M.A.J.; Lyulin, A.V.

2012-01-01

We have performed molecular-dynamics simulations of atactic polystyrene thin films to study the effect of shear rate, pressure, and temperature on the stress-strain behaviour, the relevant energetic contributions and non-affine displacements of polymer chains during constant-shear deformation. Under

System effectiveness of a targeted free mass distribution of long lasting insecticidal nets in Zanzibar, Tanzania

Directory of Open Access Journals (Sweden)

Abass Ali K

2010-06-01

Full Text Available Abstract Background Insecticide-treated nets (ITN and long-lasting insecticidal treated nets (LLIN are important means of malaria prevention. Although there is consensus regarding their importance, there is uncertainty as to which delivery strategies are optimal for dispensing these life saving interventions. A targeted mass distribution of free LLINs to children under five and pregnant women was implemented in Zanzibar between August 2005 and January 2006. The outcomes of this distribution among children under five were evaluated, four to nine months after implementation. Methods Two cross-sectional surveys were conducted in May 2006 in two districts of Zanzibar: Micheweni (MI on Pemba Island and North A (NA on Unguja Island. Household interviews were conducted with 509 caretakers of under-five children, who were surveyed for socio-economic status, the net distribution process, perceptions and use of bed nets. Each step in the distribution process was assessed in all children one to five years of age for unconditional and conditional proportion of success. System effectiveness (the accumulated proportion of success and equity effectiveness were calculated, and predictors for LLIN use were identified. Results The overall proportion of children under five sleeping under any type of treated net was 83.7% (318/380 in MI and 91.8% (357/389 in NA. The LLIN usage was 56.8% (216/380 in MI and 86.9% (338/389 in NA. Overall system effectiveness was 49% in MI and 87% in NA, and equity was found in the distribution scale-up in NA. In both districts, the predicting factor of a child sleeping under an LLIN was caretakers thinking that LLINs are better than conventional nets (OR = 2.8, p = 0.005 in MI and 2.5, p = 0.041 in NA, in addition to receiving an LLIN (OR = 4.9, p Conclusions Targeted free mass distribution of LLINs can result in high and equitable bed net coverage among children under five. However, in order to sustain high effective coverage, there

Preparation and Characterization of Wood Plastic Composite Made Up of Durian Husk Fiber and Recycled Polystyrene Foam.

Directory of Open Access Journals (Sweden)

Koay Seong Chun

2018-01-01

Full Text Available Polystyrene foam is one of the major plastic waste that hardly to recycle. The present research is aims to recycle polystyrene foam as raw material to produce wood plastic composites (WPC. The WPC was produced from recycled polystyrene (rPS and durian husk fiber (DHF using melt compound and compression moulding processes. This paper is focus on effect of fiber content on tensile and thermal properties of rPS/DHF composite. The results found the tensile strength modulus of this WPC increased at higher fiber content, but elongation at break was reduced. However, this composites exhibited an early thermal degradation when subjected to high temperature and this was commonly found among WPC. The thermal degradation of rPS/DHF composites yielded high percentage of char residue due to char formation of DHF. Overall, the rPS/DHF composites with 60 phr fiber content able to achieved strength slight above 16 MPa without any chemical treatment additives. This indicates the rPS/DHF composites can be a potential WPC if further modify with to improve its strength.

The mechanical and physical properties of concrete containing polystyrene beads as aggregate and palm oil fuel ash as cement replacement material

Science.gov (United States)

Adnan, Suraya Hani; Abadalla, Musab Alfatih Salim; Jamellodin, Zalipah

2017-10-01

One of the disadvantages of normal concrete is the high self-weight of the concrete. Density of the normal concrete is in the range of 2200 kg/m3 to 2600 kg/ m3. This heavy self-weight make it as an uneconomical structural material. Advantages of expended polystyrene beads in lightweight concrete is its low in density which can reduce the dead load (self-weight) Improper disposal of the large quantity of palm oil fuel ash which has been produced may contribute to environmental problem in future. In this study, an alternative of using palm oil fuel ash as a cement replacement material is to improve the properties of lightweight concrete. The tests conducted in this study were slump test, compression strength, splitting tensile and water absorption test. These samples were cured under water curing condition for 7, 28 and 56 days before testing. Eight types of mixtures were cast based on percentage (25%, 50%) of polystyrene beads replacement for control samples and (25%, 50%) of polystyrene beads by different ratio 10%, 15%, and 20% replacement of palm oil fuel ash, respectively. Samples with 25% polystyrene beads and 10% palm oil fuel ash obtained the highest compressive strength which is 16.8 MPa, and the splitting tensile strength is 1.57 MPa. The water absorption for samples 25%, 50% polystyrene and 20% palm oil fuel ash is 3.89% and 4.67%, respectively which is lower compared to control samples.

Coarse-grained simulations of polyelectrolyte complexes: MARTINI models for poly(styrene sulfonate) and poly(diallyldimethylammonium)

Energy Technology Data Exchange (ETDEWEB)

Vögele, Martin [Institute for Computational Physics, University of Stuttgart, Stuttgart (Germany); Department of Theoretical Biophysics, Max Planck Institute of Biophysics, Frankfurt a. M. (Germany); Holm, Christian; Smiatek, Jens, E-mail: smiatek@icp.uni-stuttgart.de [Institute for Computational Physics, University of Stuttgart, Stuttgart (Germany)

2015-12-28

We present simulations of aqueous polyelectrolyte complexes with new MARTINI models for the charged polymers poly(styrene sulfonate) and poly(diallyldimethylammonium). Our coarse-grained polyelectrolyte models allow us to study large length and long time scales with regard to chemical details and thermodynamic properties. The results are compared to the outcomes of previous atomistic molecular dynamics simulations and verify that electrostatic properties are reproduced by our MARTINI coarse-grained approach with reasonable accuracy. Structural similarity between the atomistic and the coarse-grained results is indicated by a comparison between the pair radial distribution functions and the cumulative number of surrounding particles. Our coarse-grained models are able to quantitatively reproduce previous findings like the correct charge compensation mechanism and a reduced dielectric constant of water. These results can be interpreted as the underlying reason for the stability of polyelectrolyte multilayers and complexes and validate the robustness of the proposed models.

Coarse-grained simulations of polyelectrolyte complexes: MARTINI models for poly(styrene sulfonate) and poly(diallyldimethylammonium)

International Nuclear Information System (INIS)

Vögele, Martin; Holm, Christian; Smiatek, Jens

2015-01-01

We present simulations of aqueous polyelectrolyte complexes with new MARTINI models for the charged polymers poly(styrene sulfonate) and poly(diallyldimethylammonium). Our coarse-grained polyelectrolyte models allow us to study large length and long time scales with regard to chemical details and thermodynamic properties. The results are compared to the outcomes of previous atomistic molecular dynamics simulations and verify that electrostatic properties are reproduced by our MARTINI coarse-grained approach with reasonable accuracy. Structural similarity between the atomistic and the coarse-grained results is indicated by a comparison between the pair radial distribution functions and the cumulative number of surrounding particles. Our coarse-grained models are able to quantitatively reproduce previous findings like the correct charge compensation mechanism and a reduced dielectric constant of water. These results can be interpreted as the underlying reason for the stability of polyelectrolyte multilayers and complexes and validate the robustness of the proposed models

Ternary hybrid polymeric nanocomposites through grafting of polystyrene on graphene oxide-TiO{sub 2} by surface initiated atom transfer radical polymerization (SI-ATRP)

Energy Technology Data Exchange (ETDEWEB)

Kumar, Arvind; Bansal, Ankushi; Behera, Babita; Jain, Suman L.; Ray, Siddharth S., E-mail: ssray@iip.res.in

2016-04-01

A ternary hybrid of graphene oxide-titania-polystyrene (GO-TiO{sub 2}-PS) nanocomposite is developed where polystyrene composition is regulated by controlling growth of polymer chains and nanoarchitectonics is discussed. Graphene Oxide-TiO{sub 2} (GO-TiO{sub 2}) nanocomposite is prepared by in-situ hydrothermal method and the surface is anchored with α-bromoisobutyryl bromide to activate GO-TiO{sub 2} as initiator for polymerization. In-situ grafting of polystyrene through surface initiated atom transfer radical polymerization (SI- ATRP) on this Br-functionalized nano-composite initiator yields GO-TiO{sub 2}-PS ternary hybrid. Varying the monomer amount and keeping the concentration of initiator constant, polystyrene chain growth is regulated with narrow poly-dispersivity to achieve desired composition. This composite is well characterized by various analytical techniques like FTIR, XRD, DSC, SEM, TEM, and TGA. - Highlights: • Nanocomposite of ternary hybrid of GO-TiO{sub 2} with polystyrene. • PS is surface grafted on GO-TiO{sub 2}. • Polymer chain lengths are well regulated by SI-ATRP living polymerization. • Thermal stability of this hybrid is relatively high.

Physical conditions, dynamics and mass distribution in the center of the galaxy

Science.gov (United States)

Genzel, R.; Townes, C. H.

1987-01-01

Investigations of the central 10 pc of the Galaxy, and conclusions on energetics, dynamics, and mass distribution derived from X and gamma ray measurements and from infrared and microwave studies, especially from spectroscopy, high resolution imaging, and interferometry are reviewed. Evidence for and against a massive black hole is analyzed.

TWO MASS DISTRIBUTIONS IN THE L 1641 MOLECULAR CLOUDS: THE HERSCHEL CONNECTION OF DENSE CORES AND FILAMENTS IN ORION A

International Nuclear Information System (INIS)

Polychroni, D.; Schisano, E.; Elia, D.; Molinari, S.; Turrini, D.; Rygl, K. L. J.; Benedettini, M.; Busquet, G.; Di Giorgio, A. M.; Pestalozzi, M.; Pezzuto, S.; Roy, A.; André, Ph.; Hennemann, M.; Hill, T.; Könyves, V.; Martin, P.; Di Francesco, J.; Arzoumanian, D.; Bontemps, S.

2013-01-01

We present Herschel survey maps of the L 1641 molecular clouds in Orion A. We extracted both the filaments and dense cores in the region. We identified which of the dense sources are proto- or pre-stellar, and studied their association with the identified filaments. We find that although most (71%) of the pre-stellar sources are located on filaments there, is still a significant fraction of sources not associated with such structures. We find that these two populations (on and off the identified filaments) have distinctly different mass distributions. The mass distribution of the sources on the filaments is found to peak at 4 M ☉ and drives the shape of the core mass function (CMF) at higher masses, which we fit with a power law of the form dN/dlogM∝M –1.4±0.4 . The mass distribution of the sources off the filaments, on the other hand, peaks at 0.8 M ☉ and leads to a flattening of the CMF at masses lower than ∼4 M ☉ . We postulate that this difference between the mass distributions is due to the higher proportion of gas that is available in the filaments, rather than in the diffuse cloud

TWO MASS DISTRIBUTIONS IN THE L 1641 MOLECULAR CLOUDS: THE HERSCHEL CONNECTION OF DENSE CORES AND FILAMENTS IN ORION A

Energy Technology Data Exchange (ETDEWEB)

Polychroni, D. [Department of Astrophysics, University of Athens, Astronomy and Mechanics, Faculty of Physics, Panepistimiopolis, 15784 Zografos, Athens (Greece); Schisano, E.; Elia, D.; Molinari, S.; Turrini, D.; Rygl, K. L. J.; Benedettini, M.; Busquet, G.; Di Giorgio, A. M.; Pestalozzi, M.; Pezzuto, S. [Istituto di Astrofisica e Planetologia Spaziali (INAF-IAPS), via del Fosso del Cavaliere 100, I-00133 Roma (Italy); Roy, A.; André, Ph.; Hennemann, M.; Hill, T.; Könyves, V. [Laboratoire AIM, CEA/IRFU CNRS/INSU Université Paris Diderot, Paris-Saclay, F-91191 Gif-sur-Yvette (France); Martin, P. [Canadian Institute for Theoretical Astrophysics, University of Toronto, 60 St. George Street, Toronto, ON M5S 3H8 (Canada); Di Francesco, J. [National Research Council Canada, 5071 West Saanich Road, Victoria, BC V9E 2E7 (Canada); Arzoumanian, D. [IAS, CNRS (UMR 8617), Université Paris-Sud, Bâtiment 121, F-91400 Orsay (France); Bontemps, S., E-mail: dpolychroni@phys.uoa.gr [Université de Bordeaux, Laboratoire d' Astrophysique de Bordeaux, CNRS/INSU, UMR 5804, BP 89, F-33271, Floirac Cedex (France); and others

2013-11-10

We present Herschel survey maps of the L 1641 molecular clouds in Orion A. We extracted both the filaments and dense cores in the region. We identified which of the dense sources are proto- or pre-stellar, and studied their association with the identified filaments. We find that although most (71%) of the pre-stellar sources are located on filaments there, is still a significant fraction of sources not associated with such structures. We find that these two populations (on and off the identified filaments) have distinctly different mass distributions. The mass distribution of the sources on the filaments is found to peak at 4 M {sub ☉} and drives the shape of the core mass function (CMF) at higher masses, which we fit with a power law of the form dN/dlogM∝M {sup –1.4±0.4}. The mass distribution of the sources off the filaments, on the other hand, peaks at 0.8 M {sub ☉} and leads to a flattening of the CMF at masses lower than ∼4 M {sub ☉}. We postulate that this difference between the mass distributions is due to the higher proportion of gas that is available in the filaments, rather than in the diffuse cloud.

Occurrence and spatial distribution of microplastics in sediments from Norderney

International Nuclear Information System (INIS)

Dekiff, Jens H.; Remy, Dominique; Klasmeier, Jörg; Fries, Elke

2014-01-01

The spatial distribution of small potential microplastics (SPM) ( 1 mm) was also examined. Small microparticles were extracted from 36 one kg sediment samples and analysed by visual microscopic inspection and partly by thermal desorption pyrolysis gas chromatography/mass spectrometry. The smallest particle size that could be analysed with this method was estimated to be 100 μm. The mean number of SPM at the three sampling sites (n = 12) was 1.7, 1.3 and 2.3 particles per kg dry sediment, respectively. SPM were identified as polypropylene, polyethylene, polyethylene terephthalate, polyvinylchloride, polystyrene and polyamide. The organic plastic additives found were benzophenone, 1,2-benzenedicarboxylic acid, dimethyl phthalate, diethylhexyl phthalate, dibutyl phthalate, diethyl phthalate, phenol and 2,4-di-tert-butylphenol. Particles were distributed rather homogenously and the occurrence of SPM did not correlate with that of VPD. -- Highlights: • The small-scale variability of small potential microplastics (<1 mm) occurrence in beach sediments was studied. • Within 500 m, small potential microplastics (<1 mm) were distributed rather homogeneously in investigated beach sediments. • The occurrence of small potential microplastics (<1 mm) did not correlate with that of visible plastic debris. • Procedural contamination of sediments by fibres (blank) constitutes an analytical problem. • These findings must be considered when setting up standardized monitoring protocols. -- On a small scale within 500 m, small microplastics are distributed rather homogeneously in sediments from the North Sea island of Norderney

Evolution models of helium white dwarf-main-sequence star merger remnants: the mass distribution of single low-mass white dwarfs

Science.gov (United States)

Zhang, Xianfei; Hall, Philip D.; Jeffery, C. Simon; Bi, Shaolan

2018-02-01

It is not known how single white dwarfs with masses less than 0.5Msolar -- low-mass white dwarfs -- are formed. One way in which such a white dwarf might be formed is after the merger of a helium-core white dwarf with a main-sequence star that produces a red giant branch star and fails to ignite helium. We use a stellar-evolution code to compute models of the remnants of these mergers and find a relation between the pre-merger masses and the final white dwarf mass. Combining our results with a model population, we predict that the mass distribution of single low-mass white dwarfs formed through this channel spans the range 0.37 to 0.5Msolar and peaks between 0.45 and 0.46Msolar. Helium white dwarf--main-sequence star mergers can also lead to the formation of single helium white dwarfs with masses up to 0.51Msolar. In our model the Galactic formation rate of single low-mass white dwarfs through this channel is about 8.7X10^-3yr^-1. Comparing our models with observations, we find that the majority of single low-mass white dwarfs (<0.5Msolar) are formed from helium white dwarf--main-sequence star mergers, at a rate which is about $2$ per cent of the total white dwarf formation rate.

Fission fragment mass distribution in the 13C+182W and 176Yb reactions

International Nuclear Information System (INIS)

Ramachandran, K.; Hinde, D.J.; Dasgupta, M.; Williams, E.; Wakhle, A.; Luong, D.H.; Evers, M.; Carter, I.P.; Das, S.

2014-01-01

Fission fragment mass distributions have been measured for many systems and found to be asymmetric in the fission of nuclei with nucleon number A in the range 228-258 and proton number Z in the range 90-100. For lighter systems, it has been observed that fission fragment mass distributions are usually symmetric. At high excitation energies the shell effects are expected to vanish and the nuclei are expected to behave like a charged liquid drop; hence, only symmetric fission is expected for all the nuclei. Even after much experimental and theoretical work in this field, the rate of damping of shell effects with excitation energy is not well known. This abstract reports our measurements with 13 C beams on 182 W and 176 Yb targets

Damping of Mechanical Waves with Styrene/Butadiene Rubber Filled with Polystyrene Particle: Effects of Particles Size and Wave Frequency

Directory of Open Access Journals (Sweden)

M. Haghgo

2007-08-01

Full Text Available Utilizing polymeric materials for damping mechanical waves is of great importance in various fields of applications such as military camouflage, prevention of structural vibrational energy transfer, and noise attenuation. This ability originates from segmental dynamics of chain-like polymer molecules. Damping properties of styrene-butadiene rubbercontaining 10 wt% of monosize polystyrene particles with different diameters (from 80 nm to 500 μm was investigated in the frequency range of vibration, sound, and ultrasound via dynamic mechanical thermal analysis, normalsound adsorption test, and ultrasound attenuation coefficient measurement. The obtained results indicated that for different systems, containing different sizes of polystyrene particles, the area under the damping curve does not show significant change comparing to the neat SBR in the frequency range studied. However, addition of polystyrene particles, specifically nanosized particles, resulted in emergence of a secondary glass transition temperature which could be attributed to the modified dynamics of a layer of matrix molecules near the surface of PS particles. In the range of sound frequency, 0.5 to 6.3 kHz, the maximum damping was observed for the system containing polystyrene nanoparticles. However the single damping curve of neat SBR was separated into two or even three distinct curves owing to the presence of the particles. The maximum damping in the ultrasound frequency range was found for the system containing 0.5 mm polystyrene particles. This is attributed to different contributions from matrix chains dynamics and the reflection of mechanical waves from particles-matrix interface at different frequency ranges. On other words, the increase in the glass transition temperature of the elastomeric matrix phase with increasing the mechanical wave frequency causes a reduction in the contribution from matrix chains dynamics while the contribution due to diffraction from dispersed

CO2 Induced Foaming Behavior of Polystyrene near the Glass Transition

Directory of Open Access Journals (Sweden)

Salah Al-Enezi

2017-01-01

Full Text Available This paper examines the effect of high-pressure carbon dioxide on the foaming process in polystyrene near the glass transition temperature and the foaming was studied using cylindrical high-pressure view cell with two optical windows. This technique has potential applications in the shape foaming of polymers at lower temperatures, dye impregnation, and the foaming of polystyrene. Three sets of experiments were carried out at operating temperatures of 50, 70, and 100°C, each over a range of pressures from 24 to 120 bar. Foaming was not observed when the polymer was initially at conditions below Tg but was observed above Tg. The nucleation appeared to occur randomly leading to subsequent bubble growth from these sites, with maximum radius of 0.02–0.83 mm. Three models were applied on the foaming experimental data. Variable diffusivity and viscosity model (Model C was applied to assess the experimental data with the WLF equation. The model shows very good agreement by using realistic parameter values. The expansion occurs by diffusion of a dissolved gas from the supersaturated polymer envelope into the bubble.

Micellar aggregates of amylose-block-polystyrene rod-coil block copolymers in water and THF

NARCIS (Netherlands)

Loos, Katja; Böker, Alexander; Zettl, Heiko; Zhang, Mingfu; Krausch, Georg; Müller, Axel H.E.; Boker, A.; Zhang, A.F.

2005-01-01

Amylose-block-polystyrenes with various block copolymer compositions were investigated in water and in THF solution. Fluorescence correlation spectroscopy, dynamic light, scattering (DLS), and asymmetric flow field-flow fractionation with multiangle light scattering detection indicate the presence

Separation and concentration of lead, uranium and copper using polystyrene resins functionalised with azobenzylphosphonic acid ligands

International Nuclear Information System (INIS)

Ueda, Kazumasa; Sato, Yuko; Yoshimura, Osamu; Yamamoto, Yoshikazu

1988-01-01

Two polystyrene resins functionalised with azobenzylphosphonic acid ligands were synthesised and applications for the concentration, separation and determination of micro- or milligram concentrations of metal ions were studied. Physical and chemical properties such as specific mass, water content and ion-exchange capacity were measured and the characteristics of the resins were examined. The resins were especially useful for the concentration of Pbsup(II), Usup(VI) and Cusup(II) by batch and column operations, and effective separations of Pbsup(II) from Group VIII and IIB ions could be achieved by selecting the eluents. Trace amounts of Pbsup(II), Usup(VI), Cusup(II), Mnsup(II), Znsup(II) and Fesup(III) were quantitatively retained on the resin columns at neutral pH and easily recovered by elution with 2M HCl and 2M HNO 3 . The resins were successfully applied to the concentration of trace amounts of metals in river and sea waters prior to spectroscopic determinations. (author)

Effect of acid treated carbon nanotubes on mechanical, rheological and thermal properties of polystyrene nanocomposites

KAUST Repository

Amr, Issam Thaher; Al-Amer, Adnan M J; Selvin, Thomas P.; Al-Harthi, Mamdouh Ahmed; Girei, Salihu Adamu; Sougrat, Rachid; Atieh, Muataz Ali

2011-01-01

In this work, multiwall carbon nanotubes (CNT) were functionalized by acid treatment and characterized using Fourier Transform Infrared Spectroscopy (FTIR) and thermogravimetric analysis (TGA). Polystyrene/CNT composites of both the untreated

The Eating Habits of Milky Way-mass Halos: Destroyed Dwarf Satellites and the Metallicity Distribution of Accreted Stars

Science.gov (United States)

Deason, Alis J.; Mao, Yao-Yuan; Wechsler, Risa H.

2016-04-01

We study the mass spectrum of destroyed dwarfs that contribute to the accreted stellar mass of Milky Way (MW)-mass (Mvir ˜ 1012.1 M⊙) halos using a suite of 45 zoom-in dissipationless simulations. Empirical models are employed to relate (peak) subhalo mass to dwarf stellar mass, and we use constraints from z = 0 observations and hydrodynamical simulations to estimate the metallicity distribution of the accreted stellar material. The dominant contributors to the accreted stellar mass are relatively massive dwarfs with Mstar ˜ 108-1010M⊙. Halos with more quiescent accretion histories tend to have lower mass progenitors (108-109 M⊙), and lower overall accreted stellar masses. Ultra-faint mass (Mstar 108 M⊙ can contribute a considerable fraction (˜20%-60%) of metal-poor stars if their metallicity distributions have significant metal-poor tails. Finally, we find that the generic assumption of a quiescent assembly history for the MW halo seems to be in tension with the mass spectrum of its surviving dwarfs. We suggest that the MW could be a “transient fossil” a quiescent halo with a recent accretion event(s) that disguises the preceding formation history of the halo.

Effects of statistical distribution of joint trace length on the stability of tunnel excavated in jointed rock mass

Directory of Open Access Journals (Sweden)

Kayvan Ghorbani

2015-12-01

Full Text Available The rock masses in a construction site of underground cavern are generally not continuous, due to the presence of discontinuities, such as bedding, joints, faults, and fractures. The performance of an underground cavern is principally ruled by the mechanical behaviors of the discontinuities in the vicinity of the cavern. During underground excavation, many surrounding rock failures have close relationship with joints. The stability study on tunnel in jointed rock mass is of importance to rock engineering, especially tunneling and underground space development. In this study, using the probability density distribution functions of negative exponential, log-normal and normal, we investigated the effect of joint trace length on the stability parameters such as stress and displacement of tunnel constructed in rock mass using UDEC (Universal Distinct Element Code. It was obtained that normal distribution function of joint trace length is more critical on the stability of tunnel, and exponential distribution function has less effect on the tunnel stability compared to the two other distribution functions.

Subterranean Termite Resistance of Polystyrene-Treated Wood from Three Tropical Wood Species

Directory of Open Access Journals (Sweden)

Yusuf Sudo Hadi

2016-07-01

Full Text Available The objective of this work was to investigate the resistance of three Indonesian wood species to termite attack. Samples from sengon (Falcataria moluccana, mangium (Acacia mangium, and pine (Pinus merkusii were treated with polystyrene at loading levels of 26.0%, 8.6%, and 7.7%, respectively. Treated and untreated samples were exposed to environmental conditions in the field for 3 months. Untreated specimens of sengon, mangium, and pine had resistance ratings of 3.0, 4.6, and 2.4, respectively, based on a 10-point scale from 0 (no resistance to 10 (complete or near-complete resistance. Corresponding resistance values of 7.8, 7.2, and 8.2 were determined for specimens treated with polystyrene. Overall weight loss values of 50.3%, 23.3%, and 66.4% were found for untreated sengon, mangium, and pine samples, respectively; for treated samples, the values were 7.6%, 14.4%, and 5.1%, respectively. Based on the findings in this study, overall resistance to termite attack was higher for treated samples compared to untreated samples.

Evidence for Different Disk Mass Distributions between Early- and Late-type Be Stars in the BeSOS Survey

Energy Technology Data Exchange (ETDEWEB)

Arcos, C.; Kanaan, S.; Curé, M. [Instituto de Física y Astronomía, Facultad de Ciencias, Universidad de Valparaíso. Av. Gran Bretana 1111, Valparaíso (Chile); Jones, C. E.; Sigut, T. A. A. [Department of Physics and Astronomy, The University of Western Ontario, London, ON N6A 3K7 (Canada)

2017-06-10

The circumstellar disk density distributions for a sample of 63 Be southern stars from the BeSOS survey were found by modeling their H α emission line profiles. These disk densities were used to compute disk masses and disk angular momenta for the sample. Average values for the disk mass are 3.4 × 10{sup −9} and 9.5 × 10{sup −10} M {sub ⋆} for early (B0–B3) and late (B4–B9) spectral types, respectively. We also find that the range of disk angular momentum relative to the star is (150–200) J {sub ⋆}/ M {sub ⋆} and (100–150) J {sub ⋆}/ M {sub ⋆}, again for early- and late-type Be stars, respectively. The distributions of the disk mass and disk angular momentum are different between early- and late-type Be stars at a 1% level of significance. Finally, we construct the disk mass distribution for the BeSOS sample as a function of spectral type and compare it to the predictions of stellar evolutionary models with rapid rotation. The observed disk masses are typically larger than the theoretical predictions, although the observed spread in disk masses is typically large.

Comparison of film measurements and Monte Carlo simulations of dose delivered with very high-energy electron beams in a polystyrene phantom.

Science.gov (United States)

Bazalova-Carter, Magdalena; Liu, Michael; Palma, Bianey; Dunning, Michael; McCormick, Doug; Hemsing, Erik; Nelson, Janice; Jobe, Keith; Colby, Eric; Koong, Albert C; Tantawi, Sami; Dolgashev, Valery; Maxim, Peter G; Loo, Billy W

2015-04-01

To measure radiation dose in a water-equivalent medium from very high-energy electron (VHEE) beams and make comparisons to Monte Carlo (MC) simulation results. Dose in a polystyrene phantom delivered by an experimental VHEE beam line was measured with Gafchromic films for three 50 MeV and two 70 MeV Gaussian beams of 4.0-6.9 mm FWHM and compared to corresponding MC-simulated dose distributions. MC dose in the polystyrene phantom was calculated with the EGSnrc/BEAMnrc and DOSXYZnrc codes based on the experimental setup. Additionally, the effect of 2% beam energy measurement uncertainty and possible non-zero beam angular spread on MC dose distributions was evaluated. MC simulated percentage depth dose (PDD) curves agreed with measurements within 4% for all beam sizes at both 50 and 70 MeV VHEE beams. Central axis PDD at 8 cm depth ranged from 14% to 19% for the 5.4-6.9 mm 50 MeV beams and it ranged from 14% to 18% for the 4.0-4.5 mm 70 MeV beams. MC simulated relative beam profiles of regularly shaped Gaussian beams evaluated at depths of 0.64 to 7.46 cm agreed with measurements to within 5%. A 2% beam energy uncertainty and 0.286° beam angular spread corresponded to a maximum 3.0% and 3.8% difference in depth dose curves of the 50 and 70 MeV electron beams, respectively. Absolute dose differences between MC simulations and film measurements of regularly shaped Gaussian beams were between 10% and 42%. The authors demonstrate that relative dose distributions for VHEE beams of 50-70 MeV can be measured with Gafchromic films and modeled with Monte Carlo simulations to an accuracy of 5%. The reported absolute dose differences likely caused by imperfect beam steering and subsequent charge loss revealed the importance of accurate VHEE beam control and diagnostics.

Comparison of film measurements and Monte Carlo simulations of dose delivered with very high-energy electron beams in a polystyrene phantom

Energy Technology Data Exchange (ETDEWEB)

Bazalova-Carter, Magdalena; Liu, Michael; Palma, Bianey; Koong, Albert C.; Maxim, Peter G., E-mail: Peter.Maxim@Stanford.edu, E-mail: BWLoo@Stanford.edu; Loo, Billy W., E-mail: Peter.Maxim@Stanford.edu, E-mail: BWLoo@Stanford.edu [Department of Radiation Oncology, Stanford University, Stanford, California 94305-5847 (United States); Dunning, Michael; McCormick, Doug; Hemsing, Erik; Nelson, Janice; Jobe, Keith; Colby, Eric; Tantawi, Sami; Dolgashev, Valery [SLAC National Accelerator Laboratory, Menlo Park, California 94025 (United States)

2015-04-15

Purpose: To measure radiation dose in a water-equivalent medium from very high-energy electron (VHEE) beams and make comparisons to Monte Carlo (MC) simulation results. Methods: Dose in a polystyrene phantom delivered by an experimental VHEE beam line was measured with Gafchromic films for three 50 MeV and two 70 MeV Gaussian beams of 4.0–6.9 mm FWHM and compared to corresponding MC-simulated dose distributions. MC dose in the polystyrene phantom was calculated with the EGSnrc/BEAMnrc and DOSXYZnrc codes based on the experimental setup. Additionally, the effect of 2% beam energy measurement uncertainty and possible non-zero beam angular spread on MC dose distributions was evaluated. Results: MC simulated percentage depth dose (PDD) curves agreed with measurements within 4% for all beam sizes at both 50 and 70 MeV VHEE beams. Central axis PDD at 8 cm depth ranged from 14% to 19% for the 5.4–6.9 mm 50 MeV beams and it ranged from 14% to 18% for the 4.0–4.5 mm 70 MeV beams. MC simulated relative beam profiles of regularly shaped Gaussian beams evaluated at depths of 0.64 to 7.46 cm agreed with measurements to within 5%. A 2% beam energy uncertainty and 0.286° beam angular spread corresponded to a maximum 3.0% and 3.8% difference in depth dose curves of the 50 and 70 MeV electron beams, respectively. Absolute dose differences between MC simulations and film measurements of regularly shaped Gaussian beams were between 10% and 42%. Conclusions: The authors demonstrate that relative dose distributions for VHEE beams of 50–70 MeV can be measured with Gafchromic films and modeled with Monte Carlo simulations to an accuracy of 5%. The reported absolute dose differences likely caused by imperfect beam steering and subsequent charge loss revealed the importance of accurate VHEE beam control and diagnostics.

Effects of Neutron Emission on Fragment Mass and Kinetic Energy Distribution from Thermal Neutron-Induced Fission of 235U

International Nuclear Information System (INIS)

Montoya, M.; Rojas, J.; Saetone, E.

2007-01-01

The mass and kinetic energy distribution of nuclear fragments from thermal neutron-induced fission of 235 U(n th ,f) have been studied using a Monte-Carlo simulation. Besides reproducing the pronounced broadening in the standard deviation of the kinetic energy at the final fragment mass number around m = 109, our simulation also produces a second broadening around m = 125. These results are in good agreement with the experimental data obtained by Belhafaf et al. and other results on yield of mass. We conclude that the obtained results are a consequence of the characteristics of the neutron emission, the sharp variation in the primary fragment kinetic energy and mass yield curves. We show that because neutron emission is hazardous to make any conclusion on primary quantities distribution of fragments from experimental results on final quantities distributions

Enhancement of water retention by cross-linked carboxymethylcellulose through polystyrene grafting or γ irradiation

International Nuclear Information System (INIS)

Bhattacharjee, S.S.; Perlin, A.S.

1975-01-01

The absorbency and retention characteristics of crosslinked carboxymethylcellulose (CLCMC) with respect to water and saline can be substantially improved by two different treatments. One treatment involves γ-radioinduced grafting of polystyrene onto fibers of CLCMC. At a critical level of grafting (approximately 25 percent) the retentive capacity of the fibers is almost doubled. Particularly noteworthy is the sharp increase that follows an initial drop in retentivity. It is concluded the polystyrene becomes associated preferentially with residual ordered regions of the CLCMC macromolecule, through the localization of free radicals in these regions. A second means for enhancing the water and saline retention value of CLCMC, consists of subjecting the material to gamma irradiation from a 60 Co source. Dosages used have ranged from 1.0 to 4.8 megarads (MR), depending on the degree of substitution of the initial carboxymethylcellulose. (JGB)

Mass Distribution and Gravitational Potential of the Milky Way

Directory of Open Access Journals (Sweden)

Ninković Slobodan

2017-04-01

Full Text Available Models of mass distribution in the Milky Way are discussed where those yielding the potential analytically are preferred. It is noted that there are three main contributors to the Milky Way potential: bulge, disc and dark halo. In the case of the disc the Miyamoto-Nagai formula, as simple enough, has shown as a very good solution, but it has not been able to satisfy all requirements. Therefore, improvements, such as adding new terms or combining several Miyamoto-Nagai terms, have been attempted. Unlike the disc, in studying the bulge and dark halo the flattening is usually neglected, which offers the possibility of obtaining an exact solution of the Poisson equation. It is emphasized that the Hernquist formula, used very often for the bulge potential, is a special case of another formula and the properties of that formula are analysed. In the case of the dark halo, the slopes of its cumulative mass for the inner and outer parts are explained through a new formalism presented here for the first time.

The Surface Imprinted Polystyrene Beads Prepared via Emulsion Templates

Institute of Scientific and Technical Information of China (English)

Guo Xiang CHENG; Guang Ling PEI; Ling Gang ZENG; Li Yong ZHANG; Chao LIU

2004-01-01

In this paper, the surface imprinted cross-linked polystyrene beads were prepared via suspension polymerization with styrene (St), divinylbezene (DVB), polyvinyl alcohol (PVA1788), the mixture of Span 85 and xylene or the mixture of Span 85 and paraffin as monomer, cross-linking agent, dispersion stabilizer and templates, respectively. The results indicate that there are dense cavities on the surface of beads, and the diameter and density of cavity are related with the composition and amount of emulsion template. The forming mechanism of cavity from thermodynamics and dynamics was proposed.

The dijet mass spectrum and angular distributions with the D0 detector

International Nuclear Information System (INIS)

Abachi, S.

1996-07-01

We present preliminary results from an analysis of dijet data collected during the 1994-95 Tevatron Collider run with an integrated luminosity of 91 pb -1 . Measurements of dijet mass spectra and dijet angular distributions in anti pp collisions at √s- = 1.8 TeV are compared with next-to-leading order QCD theory

Neutron emission effects on final fragments mass and kinetic energy distribution from low energy fission of 234U

International Nuclear Information System (INIS)

Montoya, M.; Rojas, J.; Lobato, I.

2008-01-01

The standard deviation of the final kinetic energy distribution (σ e ) as a function of mass of final fragments (m) from low energy fission of 234 U, measured with the Lohengrin spectrometer by Belhafaf et al., presents a peak around m = 109 and another around m = 122. The authors attribute the first peak to the evaporation of a large number of neutrons around the corresponding mass number, i.e. there is no peak on the standard deviation of the primary kinetic energy distribution (σ E ) as a function of primary fragment mass (A). The second peak is attributed to a real peak on σ E (A). However, theoretical calculations related to primary distributions made by H.R. Faust and Z. Bao do not suggest any peak on σ E (A). In order to clarify this apparent controversy, we have made a numerical experiment in which the masses and the kinetic energy of final fragments are calculated, assuming an initial distribution of the kinetic energy without structures on the standard deviation as function of fragment mass. As a result we obtain a pronounced peak on σ e (m) curve around m = 109, a depletion from m = 121 to m = 129, and an small peak around m = 122, which is not as great as that measured by Belhafaf et al. Our simulation also reproduces the experimental results on the yield of the final mass Y(m), the average number of emitted neutrons as a function of the provisional mass (calculated from the values of the final kinetic energy of the complementary fragments) and the average value of fragment kinetic energy as a function of the final mass. From our results we conclude that there are no peaks on the σ E (A) curve, and the observed peaks on σ e (m) are due to the emitted neutron multiplicity and the variation of the average fragment kinetic energy as a function of primary fragment mass. (Author)