Treatability and kinetics studies of mesophilic aerobic biodegradation of high oil and grease pet food wastewater

International Nuclear Information System (INIS)

Liu, Victor Lei; Nakhla, G.; Bassi, A.

2004-01-01

In this work, batch activated sludge studies were investigated for the treatment of raw pet food wastewater characterized by oil and grease concentrations of 50,000-66,000 mg/L, COD and BOD concentrations of 100,000 and 80,000 mg/L, respectively, as well as effluent from an existing anaerobic digester treating the aforementioned wastewater. A pre-treatment process, dissolved air flotation (DAF) achieved 97-99% reduction in O and G to about 400-800 mg/L, which is still atypically high for AS. The batch studies were conducted using a 4-L bioreactor at room temperature (21 deg. C) under different conditions. The experimental results showed for the DAF pretreated effluent, 92% COD removal efficiency can be achieved by using conventional activated sludge system at a 5 days contact time and applied initial soluble COD to biomass ratio of 1.17 mg COD/mg VSS. Similarly for the digester effluent at average oil and grease concentrations of 13,500 mg/L, activated sludge affected 63.7-76.2% soluble COD removal at 5 days. The results also showed that all kinetic data best conformed to the zero order biodegradation model with a low biomass specific maximum substrate utilization rate of 0.168 mg COD/mg VSS day reflecting the slow biodegradability of the wastewater even after 99% removal of oil and grease

The processing of used cooking oil (yellow grease) using combination of adsorption and ultrafiltration membrane processes

Science.gov (United States)

Rosnelly, C. M.; Sofyana; Amalia, D.; Sarah, S.

2018-03-01

Yellow grease is used cooking oil whose quality has degraded due to the oxidation, polymerization, or hydrolysis process. In previous studies, yellow grease refining had been conducted either by adsorption or by using membrane. In this study, adsorption process using adsorbent from bagasse activated with H3PO4 12.5%, and ultrafiltration using Polyethersulfone (PES) membrane were combined. In adsorption stage, several variation of bagasse mass was fed into 200 ml of yellow grease and stirred for 60 minutes at 60 rpm. Yellow grease produced from adsorption with best condition was then processed using ultrafiltration membran that is PES membran with concentration by 15 wt % with transmembrane pressure variation by 0.5; 1; 1.5; 2; and 2.5 Bar. Analysis of yellow grease characteristics before refined showed its acid number, peroxide number, iodine number, and water content respectively by 2.68 mgKOH/Kg; 5.97 Meq/Kg; 51,48; and 1.29%. Characteristics of yellow grease after adsorption at its best condition on the parameters of acid number, peroxide number, iodine number, and water content are respectively by 2.55 mgKOH/Kg; 4.19 Meq/Kg; 40,02; and 0.27%. Characteristics of yellow grease after ultrafiltration at its best condition on the parameters of acid number, peroxide number, iodine number, and water content are respectively by 1.12 mgKOH/Kg; 1.8 Meq/Kg; 41,36; and 0.02%. Combination of adsorption and ultrafiltration processes for yellow grease processing showed decreasing value on the parameters of acid number, peroxide number, and water content that conforms to the SNI quality standard, but has not been able to increase the iodine number.

International evolution of fat, oil and grease (FOG) waste management - A review

OpenAIRE

Wallace, Thomas; Gibbons, David; O'Dwyer, Michael; Curran, Thomas P.

2017-01-01

In recent years, issues relating to fat, oil and grease (FOG) in sewer systems have intensified. In the media, sewer blockages caused by FOG waste deposits, commonly referred to as 'fatbergs', are becoming a reminder of the problems that FOG waste can cause when left untreated. These FOG blockages lead to sanitary sewer overflows, property flooding and contamination of water bodies with sewage. Despite these financial and environmentally detrimental effects, a homogenous FOG waste management ...

Film Thickness and Friction Relationship in Grease Lubricated Rough Contacts

Directory of Open Access Journals (Sweden)

David Gonçalves

2017-08-01

Full Text Available The relationship between the film generation and the coefficient of friction in grease lubricated contacts was investigated. Ball-on-disc tests were performed under different operating conditions: entrainment speed, lubricant temperature and surface roughness. The tests were performed with fully formulated greases and their base oils. The greases were formulated with different thickener types and also different base oils natures and viscosities. Film thickness measurements were performed in ball-on-glass disc tests, and Stribeck curves were measured in ball-on-steel disc tests with discs of different roughness. The role of the thickener and the base oil nature/viscosity on the film thickness and coefficient of friction was addressed and the greases’ performance was compared based on their formulation.

Experimental Comparison of the Behavior between Base Oil and Grease Starvation Based on Inlet Film Thickness

Directory of Open Access Journals (Sweden)

D. Kostal

2017-03-01

Full Text Available This paper deals with the experimental study of an elastohydrodynamic contact under conditions of insufficient lubricant supply. Starvation level of this type of the contact may be experimentally determined based on the position of the meniscus, but this way can't determine all levels of starvation. Consequent development in the field of tribology achieved theoretical model that can determine all levels of starvation by dependency on the thickness of the lubricant film entering the contact, but it is difficult for experimental verification. The main goal of this work is an experimental study and description of the behavior of the elastohydrodynamic contact with controlled thickness of the lubricant film at the contact input. Contact was lubricated by the base oil and the grease and compared. Results were surprising because the only differences between oil and grease were observed for more viscous lubricants at thicker film layer entering to the contact.

Microbial community adaptation influences long-chain fatty acid conversion during anaerobic codigestion of fats, oils, and grease with municipal sludge.

Science.gov (United States)

Ziels, Ryan M; Karlsson, Anna; Beck, David A C; Ejlertsson, Jörgen; Yekta, Sepehr Shakeri; Bjorn, Annika; Stensel, H David; Svensson, Bo H

2016-10-15

Codigesting fats, oils, and greases with municipal wastewater sludge can greatly improve biomethane recovery at wastewater treatment facilities. Process loading rates of fats, oils, and greases have been previously tested with little knowledge of the digester microbial community structure, and high transient fat loadings have led to long chain fatty acid (LCFA) accumulation and digester upsets. This study utilized recently-developed quantitative PCR assays for syntrophic LCFA-degrading bacteria along with 16S amplicon sequencing to relate changes in microbial community structure to LCFA accumulation during transient loading increases to an anaerobic codigester receiving waste restaurant oil and municipal wastewater sludge. The 16S rRNA gene concentration of the syntrophic β-oxidizing genus Syntrophomonas increased to ∼15% of the Bacteria community in the codigester, but stayed below 3% in the control digester that was fed only wastewater sludge. Methanosaeta and Methanospirillum were the dominant methanogenic genera enriched in the codigester, and together comprised over 80% of the Archaea community by the end of the experimental period. Constrained ordination showed that changes in the codigester Bacteria and Archaea community structures were related to measures of digester performance. Notably, the effluent LCFA concentration in the codigester was positively correlated to the specific loading rate of waste oil normalized to the Syntrophomonas 16S rRNA concentration. Specific loading rates of 0-1.5 × 10(-12) g VS oil/16S gene copies-day resulted in LCFA concentrations below 30 mg/g TS, whereas LCFA accumulated up to 104 mg/g TS at higher transient loading rates. Based on the community-dependent loading limitations found, enhanced biomethane production from high loadings of fats, oils and greases can be achieved by promoting a higher biomass of slow-growing syntrophic consortia, such as with longer digester solids retention times. This work also

Semi-continuous anaerobic co-digestion of thickened waste activated sludge and fat, oil and grease

International Nuclear Information System (INIS)

Wan Caixia; Zhou Quancheng; Fu Guiming; Li Yebo

2011-01-01

Highlights: → Co-digestion of thickened waste activated sludge (TWAS) with fat, oil and grease (FOG). → Co-digestion of TWAS and FOG at 64% VS increased biogas production by 137%. → FOG addition ratio at 74% of total VS caused inhibition of the anaerobic digestion process. → Micronutrients addition did not significantly improve the biogas production and digestion stabilization. - Abstract: Co-digestion of thickened waste activated sludge (TWAS) and fat, oil and grease (FOG) was conducted semi-continuously under mesophilic conditions. The results showed that daily methane yield at the steady state was 598 L/kg VS added when TWAS and FOG (64% of total VS) were co-digested, which was 137% higher than that obtained from digestion of TWAS alone. The biogas composition was stabilized at a CH 4 and CO 2 content of 66.8% and 29.5%, respectively. Micronutrients added to co-digestion did not improve the biogas production and digestion stabilization. With a higher addition of FOG (74% of total VS), the digester initially failed but was slowly self-recovered; however, the methane yield was only about 50% of a healthy reactor with the same organic loading rate.

Fat, oil and grease reduction in commercial kitchen ductwork: A novel biological approach.

Science.gov (United States)

Mudie, S; Vahdati, M

2017-03-01

Recent research has characterised emissions upon cooking a variety of foods in a commercial catering environment in terms of volume, particle size and composition. However, there has been limited focus on the deposition of solid grease in commercial kitchen ductwork, the sustainability of these systems and their implications on the heat recovery potential of kitchen ventilation extract air. This paper reviews the literature concerning grease, commonly referred to as Fat, Oils and Grease (FOG) abatement strategies and finds that many of these systems fall short of claimed performances. Furthermore these technologies often add to the energy cost of the operation and reduce the potential application of heat recovery in the ventilation ductwork. The aim of this study was to develop and evaluate a novel FOG removal system, with a focus on low environmental impact. The novel FOG removal system, utilises the biological activity of Bacillus subtilis and associated enzymes. The biological reagent is delivered via a misting system. The temperature, relative humidity and FOG deposit thickness were measured in the ductwork throughout a 3month trial period. FOG deposit thickness was reduced by 47% within 7weeks. The system was found to be effective at reducing the FOG deposit thickness with minimal energy cost and impact upon the kitchen and external environment. Internal ductwork operating temperature was measured with respect to future heat recovery potential and a reduction of 7°C was observed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Field Demonstration for Biodegradable Military Multipurpose Grease

National Research Council Canada - National Science Library

Rhee, In-Sik

2001-01-01

Soils and ground water at many military facilities throughout the United States have been contaminated with petroleum based products, such as engine oils, greases, hydraulic fluids, and fuels, often...

Accelerated Testing of UH-60 Viscous Bearings for Degraded Grease Fault

Science.gov (United States)

Dykas, Brian; Hood, Adrian; Krantz, Timothy; Klemmer, Marko

2015-01-01

An accelerated aging investigation of critical aviation bearings lubricated with MIL-PRF- 81322 grease was conducted to derive an understanding of the mechanisms of grease degradation and loss of lubrication over time. The current study focuses on UH-60 Black Hawk viscous damper bearings supporting the tail rotor driveshaft, which were subjected to more than 5800 hours of testing in a heated environment to accelerate the deterioration of the grease. The mechanism of grease degradation is a reduction in the oil/thickener ratio rather than the expected chemical degradation of grease constituents. Over the course of testing, vibration and temperature monitoring of bearings was conducted and trends for failing bearings are presented.

Tribological Performance of Some Pennzane(Registered Trademark) Based Greases for Vacuum Applications

Science.gov (United States)

Marchetti, Mario; Jones, William R., Jr.; Street, Kenneth W.; Wheeler, Donald; Dixon, Duane; Jansen, Mark J.; Kimura, Hiroshi

2002-01-01

Commercial greases for space applications usually fulfill the requirements imposed by the severe conditions of use. The main requirement is their ability to create an EHL film, boundary film, or both under speed, load and temperature conditions that the mechanisms will operate. Three greases, all based on a multiply alkylated cyclopentane (Pennzan(R)) base oil, were studied. The thickeners were an n-octadecylterephthalamate soap, a lithium soap, and a urea derivative. A Four-Ball Tribometer and a Spiral Orbit Tribometer were employed to evaluate the greases under ultrahigh vacuum. Results indicated that all three greases yielded very low wear rates and extended lifetimes. In addition, routine physical property data is reported for each grease.

Case study of the effectiveness of passive grease trap for management on domestic kitchen waste water

Science.gov (United States)

Nidzamuddin, M. Y.; Juffrizal, K.; Mustapha, F.; Zulfattah, Z. M.; Tan, C. F.; Taha, M. M.; Hidayah, I.; Hilwa, M. Z.

2015-05-01

Household waste, generally known as trash or garbage is mostly includes food wastes, product packaging, and other miscellaneous inorganic wastes that are coming from domestic household. Grease waste such as oil and fats can contaminate water and also clot on pipes provoking blockages. Thus, waste water from kitchen sink need a proper way of filtration. Grease trap developed in this paper is viable in trapping the grease residue. The experiments have been conducted in controlled environment and the objectives are to investigate the effectiveness of grease trap by proving the existence of retention time and the expected ratio of collected water and oil during experiment process using a prototype model.

Food Grade Grease Berbahan Baku Minyak Sawit Crude Palm Oil (Cpo Off Grade Dengan Variasi Konsentrasi Thickening

Directory of Open Access Journals (Sweden)

Martanto Totok

2017-03-01

Full Text Available Food grade grease (FGG is a kind of lubricant made from vegetable oil. Food Grease isconsidered safe for healthy and it does not pollute the environment so that it can be veryimportant for particular industries such as pharmaceutical, animal feeding, cosmetic, andespecially food industry. This study is aiming at obtaining optimum basic formulation ofthickening agent (LiOH that can produce qualified food grade grease. It is a kind of factorialexperimental study by using complete random sampling. Based on Fisher test, the treatmentshows a different result significantly. Then, it is continued by conducting Duncan’s MultipleRange Test (DMRT. 2% of activated charcoal is the best treatment because it results FFAscore, lower water content, and the bright yellow color that is shown by the score of 5.48%,0.0498 %, and 3 % that successively obtained. The treatment on thickening agent (LiOH(P1 and the revious one (L1 are the best treatment which produce qualified food gradegrease, corrosion resistance value 12.0, dropping point 130C, lubricating texture value 1,pH value 9.45, water content 0.19%, and ash content value 0.76%.

Green diesel production via catalytic hydrogenation/decarboxylation of triglycerides and fatty acids of vegetable oil and brown grease

Science.gov (United States)

Sari, Elvan

Increase in the petroleum prices, projected increases in the world's energy demand and environmental awareness have shifted the research interest to the alternative fuel technologies. In particular, green diesel, vegetable oil/animal fat/waste oil and grease derived hydrocarbons in diesel boiling range, has become an attractive alternative to biodiesel---a mixture of fatty acid methyl esters, particularly due to its superior fuel properties that are similar to petroleum diesel. Hence, green diesel can be used as a drop-in fuel in the current diesel engines. The current technology for production of green diesel-hydrodeoxygenation of triglycerides and fatty acids over conventional hydrotreating catalysts suffers from fast catalyst deactivation in the absence of hydrogen combined with high temperatures and high fatty acid content in the feedstock. Additionally, excess hydrogen requirement for hydrodeoxygenation technique leads to high production costs. This thesis proposes a new technology-selective decarboxylation of brown grease, which is a mixture of fats and oils collected from waste water trap and rich in fatty acids, over a supported noble metal catalyst that overcomes the green diesel production challenges. In contrast to other feedstocks used for liquid biofuel production, brown grease is inexpensive and non-food competing feedstock, therefore the process finds solution to waste management issues, reduces the renewable fuel production cost and does not add to the global food shortage problems. Special catalyst formulations were developed to have a high activity and stability in the absence of hydrogen in the fatty acid decarboxylation process. The study shows how catalyst innovations can lead to a new technology that overcomes the process challenges. First, the effect of reaction parameters on the activity and the selectivity of brown grease decarboxylation with minimum hydrogen consumption over an activated carbon supported palladium catalyst were

Removal of colour, turbidity, oil and grease for slaughterhouse wastewater using electrocoagulation method

Science.gov (United States)

Yusoff, Mohd Suffian; Azwan, Azlyza Mohd; Zamri, Mohd Faiz Muaz Ahmad; Aziz, Hamidi Abdul

2017-10-01

In this study electrocoagulation method is used to treat slaughterhouse wastewaters. The aim of this study is to determine the efficiency of electrocoagulation method for the removal of colour, turbidity, oil and grease of slaughterhouse wastewaters. The factors of electrode types, and voltage applied during treatment are the study parameters. The types of electrode used are Aluminium (Al) grade 6082 and Iron (Fe) grade 1050. Meanwhile, the ranges of voltage applied are 2, 4, 6, 8 volts at a time interval of 10, 20 and 30 minutes respectively. The effect of these factors on the removal of fat oil and grease (FOG), colour and turbidity are analyzed. The results show maximum removal of FOG, colour and turbidity are recorded using Fe electrode at 8 V of applied voltage with 30 minutes of treatment time. The increase in treatment time of the cell will also increase the amount of hydrogen bubbles at the cathode which results in a greater upwards flux and a faster removal of FOG,, turbidity and colour. The removal of FOG, colour and turbidity are 98%, 92% and 91 % respectively. Meanwhile, by using Al electrodes in the same condition, the removal of FOG, colour and turbidity are 91%, 85% and 87 % respectively. Whereas by using Fe-Al as electrodes pairs, the removal of FOG, colour and turbidity are found to be at 90%, 87% and 76 % respectively. In this case, the Fe-Fe pair electrodes have been proven to provide better performance for FOG, colour and turbidity removals of slaughterhouse wastewaters. Therefore, it is feasible to be considered as an alternative method for wastewater treatment.

Effects of the free fatty acid content in yellow grease on performance, carcass characteristics, and serum lipids in broilers.

Science.gov (United States)

Wu, H; Gong, L M; Guo, L; Zhang, L Y; Li, J T

2011-09-01

This study was conducted to investigate whether the free fatty acid (FFA) content of yellow grease would influence the performance and carcass characteristics of broiler chicks. A total of 432 one-day-old, male Arbor Acres broilers were randomly allotted to 1 of 4 treatments, with each treatment being applied to 6 pens of 18 chicks. The dietary treatments were based on corn and soybean meal and were supplemented with either soybean oil (2.86% FFA) or yellow grease with a low (2.74%), medium (12.59%), or high (19.05%) FFA content. The fat sources were supplemented at 1.5% of the diet during the starter phase (0 to 21 d) and at 3.0% of the diet during the grower phase (22 to 42 d). From d 0 to 42, the BW gains of chicks fed diets containing soybean oil and yellow grease with 2.74% FFA were similar. As the FFA level in the yellow grease increased, the BW gain of chicks decreased (P dressing percentage and the percentage of breast muscle in the carcass were significantly (P < 0.01) lower for broilers fed any yellow grease diet compared with birds fed soybean oil. In contrast, abdominal fat was significantly increased in diets containing yellow grease. These results demonstrate that the performance of birds fed yellow grease with a low content of FFA was essentially equal to that of birds fed soybean oil. However, because yellow grease samples containing FFA levels greater than 2.74% negatively affected bird performance, producers should exercise caution with regard to feeding broilers yellow grease with an elevated FFA content. In 42-d-old broilers, serum total cholesterol and low-density lipoprotein cholesterol levels were elevated in birds fed yellow grease, regardless of the dietary level. In contrast, serum high-density lipoprotein cholesterol and triglyceride levels were unaffected by dietary treatment. Although dietary FFA may influence triglyceride-rich lipoprotein metabolism in broilers, an explanation for the observed effects remains elusive.

Industry sector analysis, Mexico: Oil and gas field machinery and equipment. Export Trade Information

International Nuclear Information System (INIS)

1990-04-01

The Industry Sector Analyses (I.S.A.) for oil and gas field machinery and equipment contains statistical and narrative information on projected market demand, end-users, receptivity of Mexican consumers to U.S. products, the competitive situation - Mexican production, total import market, U.S. market position, foreign competition, and competitive factors, and market access - Mexican tariffs, non-tariff barriers, standards, taxes and distribution channels. The I.S.A. provides the United States industry with meaningful information regarding the Mexican market for oil and gas field machinery and equipment

Effects of Hydrocarbon-Based Grease on Rapid Prototype Material Used for Grease Retention Shrouds

Science.gov (United States)

Zakrajsek, Andrew J.; Valco, Daniel J.; Street, Kenneth W., Jr.

2010-01-01

Effects of hydrocarbon-based greases on specific rapid prototype (RP) materials used to fabricate grease retention shrouds (GRS) were explored in this study. Grease retention shrouds are being considered as a way to maintain adequate grease lubrication at the gear mesh in a prototype research transmission system. Due to their design and manufacturing flexibility, rapid prototype materials were chosen for the grease retention shrouds. In order to gain a better understanding of the short and long term effects grease pose on RP materials, research was conducted on the interaction of hydrocarbon-based grease with RP materials. The materials used in this study were durable polyamide (nylon), acrylonitrile butadiene styrene (ABS), and WaterClear 10120. Testing was conducted using Mobilgrease 28 and Syn-Tech 3913G grease (gear coupling grease). These greases were selected due to their regular use with mechanical components. To investigate the effect that grease has on RP materials, the following methods were used to obtain qualitative and quantitative data: Fourier transform infrared spectroscopy (FT-IR), interference profilometer measurements, digital camera imaging, physical shape measurement, and visual observations. To record the changes in the RP materials due to contact with the grease, data was taken before and after the grease application. Results showed that the WaterClear 10120 RP material provided the best resistance to grease penetration as compared to nylon and ABS RP materials. The manufacturing process, and thus resulting surface conditions of the RP material, played a key role in the grease penetration properties and resilience of these materials.

Design and application on experimental platform for high-speed bearing with grease lubrication

Directory of Open Access Journals (Sweden)

He Qiang

2015-12-01

Full Text Available The experimental platform for high-speed grease is an important tool for research and development of high-speed motorized spindle with grease lubrication. In this article, the experimental platform for high-speed grease is designed and manufactured which consists of the drive system, the test portion, the loading system, the lubrication system, the control system, and so on. In the meantime, the high-speed angular contact ceramic ball bearings B7005C/HQ1P4 as the research object are tested and contrasted in the grease lubrication and oil mist lubrication. The experimental platform performance is validated by contrast experiment, and the high-speed lubricated bearing performance is also studied especially in the relationship among the rotating speed,load and temperature rise. The results show that the experimental platform works steadily, accurate, and reliable in the experimental testing. And the grease lubrication ceramic ball bearings B7005C/HQ1P4 can be used in high-speed motorized spindle in the circular water cooling conditions when the rotating speed is lower than 40,000 r/min or the DN value (the value of the bearing diameter times the rotating speed is lower than the 1.44 × 106 mm r/min. Grease lubrication instead of oil mist lubrication under high-speed rotating will simplify the structure design of the high-speed motorized spindle and reduce the pollution to the environment.

Irradiation effect study on dynamic performance of grease

International Nuclear Information System (INIS)

Arakawa, Kazuo; Sasuga, Tsuneo; Hagiwara, Miyuki; Yajima, Toshio; Nakanishi, Hiroshi; Soda, Takao; Iwamoto, Takeshi.

1986-03-01

The radiation resistance of newly developed grease, MORESCO HIRAD RG-42-0, consisting of polyphenyl ether as base oil and inorganic compound as gelling agent was evaluated by conducting measurements of frictional resistance force on mechanical snubbers. After the irradiation of 60 Co γ-rays up to a predetermined dose [max. 100 MGy (10000 Mrad)], the grease was applied to mechanical snubbers. The rated load of mechanical snubbers used (standard stroke of 125 mm) was set at 0.16 ton and 1.0 ton. The frictional resistance force was measured at a velocity of 0.001, 0.01, 0.1 and 2.0 mm/sec and at temperature of 60 deg C. When the rated load was 0.16 ton, the frictional resistance force of irradiated grease was kept less than a criterion, a greater value of either 5 kgf or 1 % of the rated load, at every tested dose up to 90 MGy. In case of 1.0 ton, the frictional resistance force of the irradiated grease was less than a greater value of either 10 kgf or 1 % of the rated load at doses up to 70 MGy. (author)

Isolation of Bacterial Strain for Biodegradation of Fats, Oil and Grease

International Nuclear Information System (INIS)

Alkhatib, M.F.; Mohd Zahangir Alam; Shabana, H.F.M.

2015-01-01

Fat, oil and grease (FOG) deposition is one of the major problems that harm the environment and cause dissatisfaction for human. Uncontrolled and un-pre-treated FOG removal from the kitchen could lead to its accumulation in the piping system. Problems include the interference of fat with the aerobic microorganisms that are responsible in treating the wastewater by reducing oxygen transfer rates and for anaerobic microorganisms; their efficiency could also be reduced due to the reduction of the transport of soluble substrates to the bacterial biomass. Biodegradation could be one of the effective means to treat FOG. The main objective of this study is to isolate bacterial strains from the FOG waste and identify the strains that are capable in biodegrading FOG waste. FOG sample was collected from a sewer manhole. Enrichment technique was applied, followed by isolation of bacterial strains to determine which strain is able to degrade the FOG deposition. Some morphology for the bacterial strain was done to determine its characteristics. (author)

Problems, control, and treatment of fat, oil, and grease (FOG): a review.

Science.gov (United States)

Husain, Iman A F; Alkhatib, Ma'an Fahmi; Jammi, Mohamed Saedi; Mirghani, Mohamed E S; Bin Zainudin, Zaki; Hoda, Asif

2014-01-01

Presence of fat, oil, and grease (FOG) in wastewater is an ever-growing concern to municipalities and solid-waste facility operators. FOG enters the sewer system from restaurants, residences, and industrial food facilities. Its release into the sewer system results in a continuous build-up that causes eventual blockage of sewer pipes. Several researchers have investigated FOG deposition based on the local conditions of sewers and lifestyle. This paper attempts to review the physical and chemical characteristics of FOG, sources of FOG, and potential chemical and biological reactions of FOG. The effect of the aforementioned factors on the FOG-deposition mechanism is also discussed. Moreover, insight into the current control and treatment methods and potential reuse of FOG is highlighted. It is expected that this review would provide scientists and the concerned authorities a holistic view of the recent researches on FOG control, treatment, and reuse.

Oil and grease (O&G) removal from commercial kitchen waste water using carbonised grass as a key media

OpenAIRE

Rahmat Siti Nazahiyah; Mohd Ali Ahmad Zurisman; Wan Ibrahim Mohd Haziman; Alias Nur Azrena

2017-01-01

Oil and grease (O&G) are usually found in kitchen waste water. O&G are poorly soluble in water and can cause serious problems during the wastewater treatment. Adsorption is a fundamental process in the treatment of kitchen waste water and very economical. Activated carbon is the most effective adsorbent for this application. Therefore, the aim of the current study is to determine the potential of four materials (i.e. sand, gravel, carbonised grass (CG) and clay powder) as filter media for O&G...

Organically modified clay removes oil from water

International Nuclear Information System (INIS)

Alther, G.R.

1995-01-01

When bentonite or other clays and zeolite are modified with quaternary amines, they become organophilic. Such modified bentonites are used to remove mechanically emulsified oil and grease, and other sparingly soluble organics. Types of oil found in water can include fats, lubricants, cutting fluids, heavy hydrocarbons such as tars, grease, crude oil, diesel oils; and light hydrocarbons such as kerosene, jet fuel, and gasoline. If the organoclay is granulated, it is placed into a liquid phase carbon filter vessel to remove FOGs (Free Oil and Grease) and chlorinated hydrocarbons. In this application the clay is mixed with anthrazite to prevent early plugging of the filter by oil or grease droplets. In batch systems a powdered organoclay is employed. Organoclay removes mechanically emulsified oil and grease at 5--7 times the rate of activated carbon, or 50% of its dry weight. Oil and grease and other large sparingly soluble chlorinated hydrocarbons and NOMs (Natural Organic Matter) blind the pores of activated carbon (and ion-exchange resins), reducing its effectiveness significantly. It is therefore economically advantageous for the end user to prepolish the water before it enters carbon vessels. Operating costs can often be reduced by 50% or more

Grease lubrication in rolling bearings

CERN Document Server

Lugt, Piet M

2012-01-01

The definitive book on the science of grease lubrication for roller and needle bearings in industrial and vehicle engineering. Grease Lubrication in Rolling Bearings provides an overview of the existing knowledge on the various aspects of grease lubrication (including lubrication systems) and the state of the art models that exist today. The book reviews the physical and chemical aspects of grease lubrication, primarily directed towards lubrication of rolling bearings. The first part of the book covers grease composition, properties and rheology, including thermal

NEW RADIATION RESISTANT GREASES

Energy Technology Data Exchange (ETDEWEB)

DasGupta, Sharda; Slobodian, J. T.

1962-11-20

New radiation resistant greases were prepared from commercially available greases by carrying out radioinduced reactions with styrene. The radiation tolerances of the products were 250-1000 fold more than the starting materials and any product of similar properties now available. The various properties of the new products initially and after exposure to large radiation doses were in no case inferior to the original greases and in some respects improvements were observed. Radiation tolerance of commercial greases could be enhanced by the addition of polystyrene to form a physical mixture rather than copolymers. The reaction mechanisms involved at all stages were studied using infrared spectroscopic techniques. (P.C.H.)

Evidence for fat, oil, and grease (FOG) deposit formation mechanisms in sewer lines.

Science.gov (United States)

He, Xia; Iasmin, Mahbuba; Dean, Lisa O; Lappi, Simon E; Ducoste, Joel J; de los Reyes, Francis L

2011-05-15

The presence of hardened and insoluble fats, oil, and grease (FOG) deposits in sewer lines is a major cause of line blockages leading to sanitary sewer overflows (SSOs). Despite the central role that FOG deposits play in SSOs, little is known about the mechanisms of FOG deposit formation in sanitary sewers. In this study, FOG deposits were formed under laboratory conditions from the reaction between free fatty acids and calcium chloride. The calcium and fatty acid profile analysis showed that the laboratory-produced FOG deposit displayed similar characteristics to FOG deposits collected from sanitary sewer lines. Results of FTIR analysis showed that the FOG deposits are metallic salts of fatty acid as revealed by comparisons with FOG deposits collected from sewer lines and pure calcium soaps. Based on the data, we propose that the formation of FOG deposits occurs from the aggregation of excess calcium compressing the double layer of free fatty acid micelles and a saponification reaction between aggregated calcium and free fatty acids.

Influence of fat and oil type on the yield, physico-chemical properties, and microstructure of fat, oil, and grease (FOG) deposits.

Science.gov (United States)

Del Mundo, Dann Marie N; Sutheerawattananonda, Manote

2017-11-01

Fat, oil, and grease (FOG) deposit, in the form of calcium soap, was found to cause sanitary sewer overflows due to its adhesion on pipe walls. To address this problem, laboratory-prepared calcium soaps have been used to investigate the formation mechanisms of FOG deposits. However, the fats and oils previously utilized were limited and some soap characteristics were not examined. This research attempted to probe through the properties of calcium soaps prepared from calcium chloride and the fats and oils of chicken, pork, palm olein, soybean, olive, and coconut to further understand FOG formation and stability. Results revealed that FOG deposits may occur as smooth, paste-like material or coarse, semi-solid substance depending on their exposure to excess fat/oil and calcium. The smooth soaps with more excess fat/oil demonstrated high apparent viscosity and consistency index, while the coarse soaps with large levels of calcium signified higher melting endset. Moreover, a soap microstructure showing evident networks and lesser void area displayed higher heat and rheological stability, respectively. Overall, fats and oils with higher oleic to palmitic acid ratio such as palm olein oil, olive oil, chicken fat, and pork fat produced soaps with greater yield and degree of saponification. Hence, establishments and authorities should be alert in managing and monitoring these wastes. On the other hand, soybean oil high in linoleic acid and coconut oil high in lauric acid do not pose an immediate threat to the sewer system since they only produced soaps in small quantity. However, their soaps showed high melting endset which could pose a serious effect when accumulated at large amount. On the whole, the fatty acid profile of fats and oils, the presence of excess fat/oil, and calcium content mainly dictate the appearance, melting, rheology, and microstructure of calcium soaps. Their distinct properties can be used as criteria in predicting the condition and stability of FOG

Preliminary experimental research to detect grease stain of petroleum pipeline by sup 1 sup 3 sup 7 Cs gamma-ray transmission method

CERN Document Server

Wang Shi Heng

2002-01-01

The experimental study on the detection of grease stain for petroleum pipeline in Karamay oil-field of Xinjiang is carried out by gamma-ray transmission method. Experimental provision consists of sup 1 sup 3 sup 7 Cs gamma radiator and NaI(Tl) scintillation detector. The response of grease stain thickness of petroleum pipeline in Karamay oil-field is ln(N sub 0 /N)=0.00548 d-0.0046, and the response of paraffin thickness is ln(N sub 0 /N)=0.00522d-0.0126. The result of experiment indicates that the response of grease stain thickness is more sensitive than the response of paraffin thickness

Physical and Mechanical Properties of Palm Oil Frond and Stem Bunch for Developing Pruner and Harvester Machinery Design

Directory of Open Access Journals (Sweden)

Yazid Ismi Intara

2013-06-01

Full Text Available A development of oil palm pruner and harvester machinery design implemented in the field still faces a problem due to the lack of effective and efficient design which is need to be solved. It was noted that in order to develop the design, an early data and information of physical and mechanical properties of palm oil frond and stem fruits is critically important. The objective of the research was to obtain the physical and mechanical properties of palm oil frond and stem in order to develop the design of pruner and harvester machinery. The result showed that tool machinery was been advantageous by the physical properties of the plant i.e. the total weight of frond and leaf which enable to support the cutting process. The average of total weight of frond and leaf was 16.8 kg. The diagonal cutting trajectory was been more advantageous because of total weight and frond shape toward to the different of the plant tissue area. The measurement result shows that cutting curve follows the time required for cutting. The comparison among cutting curve shows differences in cutting thickness or length. In this case, the thickness is linear with cutting time. Besides, those curves show differences at the height which determine the maximum value of tested material cutting resistance. Alternative solution for machinery development design is pruner-harvester for height plant below 6 m and among 6 to 12 m. For below 6 m, pruner-harvester was designed by incorporating motor as power source and cutter-disc as the knife cutter. That condition was relied on that estate which was maintenance intensively commonly used cutter-disc. Pruner-harvester above 6 m and up to 12 m was improved based on manual egrek-designed by adding fresh fruit bunch alley supply glide in order to keep the fruits still in intact form. The consideration was based on affectivity and efficiency. It also considers homogenous ecological of palm oil plant which should be maintained to reduce global

Urban Waste Grease Resource Assessment

Energy Technology Data Exchange (ETDEWEB)

Wiltsee, G.

1999-03-17

This study collected and analyzed data on urban waste grease resources in 30 randomly selected metropolitan areas in the United States. Two major categories (yellow grease feedstock collected from restaurants by rendering companies; and grease trap wastes from restaurants, which can either be pumped into tank trucks for disposal or flow through municipal sewage systems into wastewater treatment plants) were considered in this study.

Quantifying fat, oil, and grease deposit formation kinetics.

Science.gov (United States)

Iasmin, Mahbuba; Dean, Lisa O; Ducoste, Joel J

2016-01-01

Fat, oil, and grease (FOG) deposits formed in sanitary sewers are calcium-based saponified solids that are responsible for a significant number of nationwide sanitary sewer overflows (SSOs) across United States. In the current study, the kinetics of lab-based saponified solids were determined to understand the kinetics of FOG deposit formation in sewers for two types of fat (Canola and Beef Tallow) and two types of calcium sources (calcium chloride and calcium sulfate) under three pH (7 ± 0.5, 10 ± 0.5, and ≈14) and two temperature conditions (22 ± 0.5 and 45 ± 0.5 °C). The results of this study displayed quick reactions of a fraction of fats with calcium ions to form calcium based saponified solids. Results further showed that increased palmitic fatty acid content in source fats, the magnitude of the pH, and temperature significantly affect the FOG deposit formation and saponification rates. The experimental data of the kinetics were compared with two empirical models: a) Cotte saponification model and b) Foubert crystallization model and a mass-action based mechanistic model that included alkali driven hydrolysis of triglycerides. Results showed that the mass action based mechanistic model was able to predict changes in the rate of formation of saponified solids under the different experimental conditions compared to both empirical models. The mass-action based saponification model also revealed that the hydrolysis of Beef Tallow was slower compared to liquid Canola fat resulting in smaller quantities of saponified solids. This mechanistic saponification model, with its ability to track the saponified solids chemical precursors, may provide an initial framework to predict the spatial formation of FOG deposits in municipal sewers using system wide sewer collection modeling software. Copyright © 2015 Elsevier Ltd. All rights reserved.

Propiedades fisicoquímicas y tribológicas de una grasa grafitada de Jatropha curcas L y jabón de litio//Physicochemical and tribological properties of graphite grease based on Jatrophacurcas L oil and lithium soap

Directory of Open Access Journals (Sweden)

Juliano‐Chitue de Assunção‐Nascimento

2014-08-01

Full Text Available Las grasas lubricantes son consideradas una dispersión coloidal de un espesante en un fluido lubricante. Los aceites vegetales son ampliamente usados en muchas formulaciones de grasas. En este trabajo se determinaron las propiedades fisicoquímicas y tribológicas de una grasa lubricante fabricada con aceite vegetal de Jatropha curcas L y jabón de litio (JC1G5. Alfa tocoferol acetato y grafito fueron usados como aditivos antioxidante y de extrema presión respectivamente. La grasa JC1G5 mostró un color negro, una temperatura de goteo de 140 oC, apropiadas propiedades de corrosión al cobre y un grado de consistencia NLGI Grado1. El efecto de la lubricación de la grasa JC1G5 fue probado, empleando una máquina de cuatro bolas y un tribómetro timken. Los resultados indican que la grasa JC1G5 posee propiedades tribológicas comparables con una grasa mineral de jabón de litio.Palabras claves: grasa, jatropha curcas L, jabón de litio, propiedades fisicoquímicas, propiedades tribológicas.______________________________________________________________________________AbstractLubricating greases are considered as colloidal dispersions of a thickener in a lubricating fluid. The vegetable oils are widely used in many formulations of greases. In this paper were determined the physicochemical and tribological properties of graphite grease based on Jatropha curcas L vegetableoil and lithium soap (JC1G5. Alpha tocofherol acetate and graphite were used as antioxidant and extreme pressure additives respectively. The grease JC1G5 showed a black color, a dropping point of 140 oC, appropriate magnitude of copper corrosion and consistency NLGI Grade 1. Lubrication performance of the grease JC1G5 was tested using the 4-ball wear tester and timken tribometer tester. Results indicate that the grease JC1G5 has tribological properties comparable to that of mineral oil base lithium grease.Key words: grease, jatrophacurcas L, lithium soap, physicochemical

Physico-chemical characterization of grease interceptors with and without biological product addition.

Science.gov (United States)

He, Xia; Osborne, Jason; de los Reyes, Francis L

2012-03-01

Hardened and insoluble fat, oil, and grease (FOG) deposits are the primary cause of sewer line blockages leading to sanitary sewer overflows (SSOs). However, there have been very few long-term assessments of the physico-chemical characteristics of full-scale grease interceptors (GIs), the first "line of defense" against FOG buildup in sewer lines. In this study, we assessed the physico-chemical characteristics of two full-scale GIs (at a restaurant and a retirement community kitchen) over a one-year period. Statistically significant differences between bioaugmented and untreated cycles were detected for several chemical and physical properties. The treated cycles had lower BOD and COD at the grease interceptor outlet. While the combined data for all treated cycles did not show lower FOG concentrations in the GI outlet compared to the combined data for all untreated cycles, comparison of specific individual treated and untreated cycles show a positive effect due to the addition of product.

Organically modified clay removes oil from water

International Nuclear Information System (INIS)

Alther, G.R.

1995-01-01

When bentonite or other clays and zeolites are modified with quaternary amines, they become organophilic. Such modified bentonites are used to remove mechanically emulsified oil and grease, and other sparingly soluble organics. If the organoclay is granulated, it is placed into a liquid phase carbon filter vessel to remove FOG's and chlorinated hydrocarbons. In this application the clay is mixed with anthrazite to prevent early plugging of the filter by oil or grease droplets. In batch systems a powered organoclay is employed. Types of oil found in water can include fats, lubricants, cutting fluids, heavy hydrocarbons such as tars, grease, crude oil, diesel oils; and light hydrocarbons such as kerosene, jet fuel, and gasoline

Fat, oil and grease deposits in sewers: characterisation of deposits and formation mechanisms.

Science.gov (United States)

Williams, J B; Clarkson, C; Mant, C; Drinkwater, A; May, E

2012-12-01

Fat, oil and grease deposits (FOG) in sewers are a major problem and can cause sewer overflows, resulting in environmental damage and health risks. Often simplistically portrayed as cooling of fats, recent research has suggested that saponification may be involved in FOG formation. However there are still questions about the mechanisms effecting transformations in sewers and the role and source of metal cations involved in saponification. This study characterises FOG deposits from pumping stations, sewers and sewage works from different water hardness zones across the UK. The sites all had previous problems with FOG and most catchments contained catering and food preparation establishments. The FOG deposits were highly variable with moisture content ranging from 15 to 95% and oil content from 0 to 548 mg/g. Generally the pumping stations had lower moisture content and higher fat content, followed by the sewers then the sewage works. The water in contact with the FOG had high levels of oil (mean of about 800 mg/L) and this may indicate poor kitchen FOG management practices. FOG fatty acid profiles showed a transformation from unsaturated to saturated forms compared to typical cooking oils. This seems to relate to ageing in the sewer network or the mechanism of formation, as samples from pumping stations had higher proportions of C18:1 compared to C16. This may be due to microbial transformations by bacteria such as Clostridium sp. in a similar process to adipocere formation. There was an association between water hardness and increased Ca levels in FOG along with harder deposits and higher melting points. A link between FOG properties and water hardness has not been previously reported for field samples. This may also be due to microbial processes, such as biocalcification. By developing the understanding of these mechanisms it may be possible to more effectively control FOG deposits, especially when combined with promotion of behavioural change. Copyright © 2012

Dual-fuel production from restaurant grease trap waste: bio-fuel oil extraction and anaerobic methane production from the post-extracted residue.

Science.gov (United States)

Kobayashi, Takuro; Kuramochi, Hidetoshi; Maeda, Kouji; Tsuji, Tomoya; Xu, Kaiqin

2014-10-01

An effective way for restaurant grease trap waste (GTW) treatment to generate fuel oil and methane by the combination of physiological and biological processes was investigated. The heat-driven extraction could provide a high purity oil equivalent to an A-grade fuel oil of Japanese industrial standard with 81-93 wt% of extraction efficiency. A post-extracted residue was treated as an anaerobic digestion feedstock, and however, an inhibitory effect of long chain fatty acid (LCFA) was still a barrier for high-rate digestion. From the semi-continuous experiment fed with the residual sludge as a single substrate, it can be concluded that the continuous addition of calcium into the reactor contributed to reducing LCFA inhibition, resulting in the long-term stable operation over one year. Furthermore, the anaerobic reactor performed well with 70-80% of COD reduction and methane productivity under an organic loading rate up to 5.3g-COD/L/d. Copyright © 2014 Elsevier Ltd. All rights reserved.

Development and evaluation of emulsifying systems of the material grease from Brazilian flora

Directory of Open Access Journals (Sweden)

Douglas Dourado

2015-10-01

Full Text Available Context: Oils and butter of seed from Brazilian biodiversity are extending the range of innovative products for cosmetics development. They have a fat potential similar to skin composition, leading to the improved performance of these product. Aims: Improve the emulsions spreadability through prior screening of grease composition and studying the viscosity, and the emulsions accelerated stability. Methods: Emulsions were formulated using oils from semiarid plants from Bahia: Syagrus coronate, Pachira retusa, and Pachira aquatica, so as to compare them with oils already standard in the production of cosmetics. Spreadability and stability tests were made comparing the results. The same criteria were used with Amazon seed butter: Virola surinamensis, Butyrospermum parkii, Astrocaryum murumuru, Theobroma cacao and Theobroma grandiflorum. For the emulsions screening and performance, a system was developed for oil/ butter, following tests of accelerated stability, viscosity, and spreadability. Results: The combined system of spreadability was optimized using screening. Emollients containing oleic and palmitic acids, and light chain fatty acids obtained good spreadability. The oil emulsion containing Pachira retusa and Virola surinamensis butter had a higher viscosity. Conclusions: With high content of fatty acids such as oleic, palmitic or the light chain fatty acids obtain an appropriated appearance, texture, and spreadability for cosmetic use. Thus, oils with a low fatty acid content may be combined with butter that have a high fatty acid content and vice-versa. Analyzing and strategically combining grease composition, one can optimize the performance of cosmetic formulations.

Study of a magnetorheological grease clutch

International Nuclear Information System (INIS)

Kavlicoglu, Barkan M; Gordaninejad, Faramarz; Wang, Xiaojie

2013-01-01

In high-speed viscous clutch applications that require low drag (viscous) torque, magnetorheological (MR) fluids are problematic due to their plastic viscosity. As the clutch speed increases the drag torque might exceed the allowable drag torque limit, because the viscous torque is proportional to the speed. To eliminate this problem, various MR greases are utilized in a clutch and their performance is examined. In the experimental study, the torque transfer capacity of a double-plate clutch for operating speeds up to 1200 rpm is conducted. Six different MR greases with various particle loadings and particle sizes are evaluated in the clutch. The rheological properties of MR grease with 90% particle loading in weight are compared with a commercially available MR fluid. The torque performance of the MR grease clutch is also compared with that of the clutch using MR fluid. It is demonstrated that the off-state (no applied magnetic field) torque output of the MR grease clutch is constant in the tested range of the operating speed. In contrast, the torque capacity of the clutch with MR fluid shows a strong dependence on the operating speed. Moreover, it is shown that the iron particle size of the MR grease does not affect the torque output. The MR greases demonstrated an up to 75% increase in the torque capacity compared to the commercial MR fluid. (paper)

Mechanisms of fat, oil and grease (FOG) deposit formation in sewer lines.

Science.gov (United States)

He, Xia; de los Reyes, Francis L; Leming, Michael L; Dean, Lisa O; Lappi, Simon E; Ducoste, Joel J

2013-09-01

FOG deposits in sewer systems have recently been shown to be metallic salts of fatty acids. However, the fate and transport of FOG deposit reactant constituents and the complex interactions during the FOG deposit formation process are still largely unknown. In this study, batch tests were performed to elucidate the mechanisms of FOG deposit formation that lead to sanitary sewer overflows (SSOs). We report the first formation of FOG deposits on a concrete surface under laboratory conditions that mimic the formation of deposits in sewer systems. Results showed that calcium, the dominant metal in FOG deposits, can be released from concrete surfaces under low pH conditions and contribute to the formation process. Small amounts of additional oil to grease interceptor effluent substantially facilitated the air/water or pipe surface/water interfacial reaction between free fatty acids and calcium to produce surface FOG deposits. Tests of different fatty acids revealed that more viscous FOG deposit solids were formed on concrete surfaces, and concrete corrosion was accelerated, in the presence of unsaturated FFAs versus saturated FFAs. Based on all the data, a comprehensive model was proposed for the mechanisms of FOG deposit formation in sewer systems. Copyright © 2013 Elsevier Ltd. All rights reserved.

Degradation Characterization of Thermal Interface Greases

Energy Technology Data Exchange (ETDEWEB)

Major, Joshua [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Narumanchi, Sreekant V [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Paret, Paul P [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Blackman, Gregory [DuPont; Wong, Arnold [DuPont; Meth, Jeffery [DuPont

2018-02-12

Thermal interface materials (TIMs) are used in power electronics packaging to minimize thermal resistance between the heat generating component and the heat sink. Thermal greases are one such class. The conformability and thin bond line thickness (BLT) of these TIMs can potentially provide low thermal resistance throughout the operation lifetime of a component. However, their performance degrades over time due to pump-out and dry-out during thermal and power cycling. The reliability performance of greases through operational cycling needs to be quantified to develop new materials with superior properties. NREL, in collaboration with DuPont, has performed thermal and reliability characterization of several commercially available thermal greases. Initial bulk and contact thermal resistance of grease samples were measured, and then the thermal degradation that occurred due to pump-out and dry-out during temperature cycling was monitored. The thermal resistances of five different grease materials were evaluated using NREL's steady-state thermal resistance tester based on the ASTM test method D5470. Greases were then applied, utilizing a 2.5 cm x 2.5 cm stencil, between invar and aluminum plates to compare the thermomechanical performance of the materials in a representative test fixture. Scanning Acoustic microscopy, thermal, and compositional analyses were performed periodically during thermal cycling from -40 degrees C to 125 degrees C. Completion of this characterization has allowed for a comprehensive evaluation of thermal greases both for their initial bulk and contact thermal performance, as well as their degradation mechanisms under accelerated thermal cycling conditions.

7 CFR 2902.31 - Greases.

Science.gov (United States)

2010-01-01

... applies are: (i) Food grade greases. Lubricants that are designed for use on food-processing equipment as... parts and equipment in locations in which there is exposure of the lubricated part to food. (ii... are designed for use on railroad tracks or heavy crane tracks. (iv) Truck greases. Lubricants that are...

Screening of thermotolerant microorganisms and application for oil separation from palm oil mill wastewater

Directory of Open Access Journals (Sweden)

Aran H-Kittikun

2007-05-01

Full Text Available The characteristics of palm oil mill wastewater (POMW were brown color, pH 3.8-4.3, temperature 48-55oC, total solids 68.2-82.1 g/l, suspended solids 26.2-65.6 g/l, oil and grease 19.1-25.1 g/l, COD 49.9-160.7g/l and BOD 32.5-75.3 g/l. After centrifugation (3,184 xg of 50 ml POMW for 10 min, the POMW was separated into 3 layers: top (oil, middle (supernatant and bottom layer (sediment. The sediment containeddry weight 1.19 g and oil and grease 1.07 g. In order to release oil and grease trapped in palm fiber debris in the POMW, cellulase- and/or xylanase-enzyme-producing and thermotolerant microorganisms wereisolated. The isolates SO1 and SO2 were isolated from soil near the first anaerobic pond of the palm oil mill. They were aerobic, Gram positive, rod shaped, thermotolerant microorganisms and produced cellulase 12.11 U/ml (3 days and 7.2 U/ml (4 days, and xylanase 50.98 U/ml (4 days and 20.42 U/ml (4 days, respectivelyin synthetic medium containing carboxymethycellulose as a carbon source. When these 2 isolates were added into the steriled POMW under shaking condition for 7 days, after centrifugation at 3,184 xg the isolate SO1gave the better % reduction of dry weight (64.66 % and of oil and grease in the bottom layer (85.32 % of the POMW.

Biopretreatment of palm oil mill effluent by thermotolerant polymer-producing fungi

Directory of Open Access Journals (Sweden)

Masao Ukita

2001-11-01

Full Text Available Palm oil industry is one of the three major agro-industries in Southern Thailand and generates large quantities of effluent with high organic matter (BOD and COD values of 58,000 and 110,000 mg/l, respectively, total solids and suspended solids (70,000 and 40,000 mg/l, respectively, oil & grease (25,600 mg/l, and has a low pH (4.5. Conventional anaerobic ponding system is normally employed in palm oil mills to treat the effluent. To increase its efficiency, biopretreatment to remove the organic matter and oil & grease by thermotolerant polymer-producing fungi was investigated. The palm oil mill effluent (POME was treated by the two thermotolerant polymer-producing fungi, Rhizopus sp. ST4 and Rhizopus sp. ST29, at 45ºC under aseptic and septic conditions. Rhizopus sp. ST4 gave the same oil & grease removal (84.2% under both conditions but COD removal under septic condition (62.2% was 8.8% higher than that under aseptic condition (53.4%. On the contrary, Rhizopus sp. ST 29 under aseptic condition showed 11% and 25.4% higher oil & grease removal (91.4% and COD removal (66.0% than those under septic condition. Comparison between the two isolates under aseptic condition revealed that Rhizopus sp. ST29 exhibited higher oil & grease removal (91.4% as well as COD removal (66.0% than those of Rhizopus sp. ST4 (84.2% and 53.4%, respectively. Under septic condition, Rhizopus sp. ST4 gave higher oil & grease removal (84.2% and COD removal (62.2% than did Rhizopus sp. ST 29 (80.5 and 40.6%, respectively.

Statistical modelling of Fat, Oil and Grease (FOG) deposits in wastewater pump sumps.

Science.gov (United States)

Nieuwenhuis, Eva; Post, Johan; Duinmeijer, Alex; Langeveld, Jeroen; Clemens, François

2018-05-15

The accumulation of FOG (Fat, Oil and Grease) deposits in sewer pumping stations results in an increase in maintenance costs, malfunctioning of pumps and, a potential increase of wastewater spills in receiving open water bodies. It is thought that a variety of parameters (e.g. geometry of the pump sump, pump operation, socioeconomic parameters of the catchment) influences the built-up of FOG. Based on a database containing data of 126 pumping stations located in five Dutch municipalities a statistical model was built. It is shown that 3 parameters are most significant in explaining the occurrence of FOG deposits: mean income of the population in a catchment, the amount of energy (kinetic and potential) per m 3 per day and the density of restaurants, bars and hotels in a catchment. Further it is shown that there are significant differences between municipalities that can be traced back to the local 'design paradigm'. For example, in Amsterdam, the design philosophy of discharging in the pump sump under the water surface (and hence maintaining a low level of turbulence in the pump sump) results in an increase of the probability of the formation of FOG. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

Understanding the spatial formation and accumulation of fats, oils and grease deposits in the sewer collection system.

Science.gov (United States)

Dominic, Christopher Cyril Sandeep; Szakasits, Megan; Dean, Lisa O; Ducoste, Joel J

2013-01-01

Sanitary sewer overflows are caused by the accumulation of insoluble calcium salts of fatty acids, which are formed by the reaction between fats, oils and grease (FOG) and calcium found in wastewaters. Different sewer structural configurations (i.e., manholes, pipes, wet wells), which vary spatially, along with other obstructions (roots intrusion) and pipe deformations (pipe sags), may influence the detrimental buildup of FOG deposits. The purpose of this study was to quantify the spatial variation in FOG deposit formation and accumulation in a pilot-scale sewer collection system. The pilot system contained straight pipes, manholes, roots intrusion, and a pipe sag. Calcium and oil were injected into the system and operated at alkaline (pH = 10) and neutral (pH = 7) pH conditions. Results showed that solid accumulations were slightly higher at neutral pH. Fourier transform infrared (FTIR) analysis on the solids samples confirmed that the solids were indeed calcium-based fatty acid salts. However, the fatty acid profiles of the solids deviated from the profile found from FOG deposits in sewer systems, which were primarily saturated fatty acids. These results confirm the work done previously by researchers and suggest an alternative fate of unsaturated fatty acids that does not lead to their incorporation in FOG deposits in full-scale sewer systems.

The reduction of oil pollutants of petroleum products storage-tanks sludge using low-cost adsorbents

Directory of Open Access Journals (Sweden)

Mokhtari-Hosseini Zahra Beagom

2017-01-01

Full Text Available Disposal of storage tank sludge in oil depots is a major environmental concern due to the high concentration of hydrocarbons involved. This paper investigates the reduction of the sludge oil pollutants with initial oil and grease concentration of about 50 mass% using low cost adsorbents. Among the examined adsorbents, sawdust indicated the maximum removal of oil and grease. The screening and optimizing of process parameters were evaluated employing Plackett-Burman design and response surface method. For the optimized conditions, more than 60 mass% of oil and grease from the sludge was removed. Moreover, it was found that sawdust adsorption of the oil and grease approximately followed the Freundlich isotherm. The results indicated that oil pollutants of sludge could be reduced using sawdust as a low-cost, available and flammable adsorbent so that thus saturated adsorbents could be used as fuel in certain industries.

Degradation Characterization of Thermal Interface Greases: Preprint

Energy Technology Data Exchange (ETDEWEB)

DeVoto, Douglas J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Major, Joshua [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Paret, Paul P [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Blackman, G. S. [DuPont Experimental Station; Wong, A. [DuPont Experimental Station; Meth, J. S. [DuPont Experimental Station

2017-08-03

Thermal interface materials (TIMs) are used in power electronics packaging to minimize thermal resistance between the heat generating component and the heat sink. Thermal greases are one such class. The conformability and thin bond line thickness (BLT) of these TIMs can potentially provide low thermal resistance throughout the operation lifetime of a component. However, their performance degrades over time due to pump-out and dry-out during thermal and power cycling. The reliability performance of greases through operational cycling needs to be quantified to develop new materials with superior properties. NREL, in collaboration with DuPont, has performed thermal and reliability characterization of several commercially available thermal greases. Initial bulk and contact thermal resistance of grease samples were measured, and then the thermal degradation that occurred due to pump-out and dry-out during temperature cycling was monitored. The thermal resistances of five different grease materials were evaluated using NREL's steady-state thermal resistance tester based on the ASTM test method D5470. Greases were then applied, utilizing a 2.5 cm x 2.5 cm stencil, between invar and aluminum plates to compare the thermomechanical performance of the materials in a representative test fixture. Scanning Acoustic microscopy, thermal, and compositional analyses were performed periodically during thermal cycling from -40 degrees Celcius to 125 degrees Celcius. Completion of this characterization has allowed for a comprehensive evaluation of thermal greases both for their initial bulk and contact thermal performance, as well as their degradation mechanisms under accelerated thermal cycling conditions.

High-purity fatty acid methyl ester production from canola, soybean, palm, and yellow grease lipids by means of a membrane reactor

International Nuclear Information System (INIS)

Cao Peigang; Dube, Marc A.; Tremblay, Andre Y.

2008-01-01

High-purity fatty acid methyl ester (FAME) was produced from different lipids, such as soybean oil, canola oil, a hydrogenated palm oil/palm oil blend, yellow grease, and brown grease, combined with methanol using a continuous membrane reactor. The membrane reactor combines reaction and separation in a single unit, provides continuous mixing of raw materials, and maintains a high molar ratio of methanol to lipid in the reaction loop while maintaining two phases during the reaction. It was demonstrated that the membrane reactor can be operated using a very broad range of feedstocks at highly similar operating conditions to produce FAME. The total glycerine and free glycerine contents of the FAME produced were below the ASTM D6751 standard after a single reaction step. Under essentially the same reaction conditions, a conventional batch reaction was not able to achieve the same degree of FAME purity. The effect of the fatty acid composition of the lipid feedstocks on the FAME purity was also shown. It was demonstrated that, due to the fatty acid composition, FAME from virgin soybean oil and virgin canola oil was produced in the membrane reactor within ASTM specifications even without a water washing step

[Determination of 3-monochloropropane-1,2-diol in grease food by solid phase extraction-derivatization-gas chromatography-mass spectrometry].

Science.gov (United States)

Xiang, Xiaoling; Wang, Liyuan; Shen, Xianghong; Li, Chunsong; Shen, Jianfu; Wu, Pinggu

2017-09-01

To establish the method of determination of 3-monochloropropane-1,2-diol( 3-MCPD) in grease food by gas chromatography-mass spectrometry( GC-MS). 3-MCPD in grease food represented by bean paste was extracted by ultrasound,purified by alkaline earth solid phase extraction column,derivatived using phenylboronic acid( PBA) and detected by GC-MS. The linearity of 3-MCPD ranged from 1-100 ng/mL,with correlation coefficient at 0. 9993.The limits of quantitation( LOQ) in soy sauce,bean paste,pepper oil were 0. 6,0. 5 and7. 0 μg/kg and limits of detection( LOD) were 1. 9,1. 6 and 18. 8 μg/kg,respectively.Average recovery rate and relative standard deviation was 78. 3%-106. 7% and 1. 9%-11. 6%( n = 6), when 3-MCPD was added in grease food at 2. 5-1000 μg/kg. The method has good purification effect and the detection sensitivity and accuracy,and can be used for the determination of 3-MCPD in grease food.

Consistency-dependent optical properties of lubricating grease studied by terahertz spectroscopy

International Nuclear Information System (INIS)

Tian Lu; Zhao Kun; Zhou Qing-Li; Shi Yu-Lei; Zhao Dong-Mei; Zhang Cun-Lin; Zhao Song-Qing; Zhao Hui; Bao Ri-Ma; Zhu Shou-Ming; Miao Qing

2011-01-01

The optical properties of four kinds of lubricating greases (urea, lithium, extreme pressure lithium, molybdenum disulfide lithium greases) with different NLGL (National Lubricant Grease Institute of America) numbers were investigated using terahertz time-domain spectroscopy. Greases with different NLGL grades have unique spectral features in the terahertz range. Comparison of the experimental data with predictions based on Lorentz—Lorenz theory exhibited that the refractive indices of each kind of lubricating grease were dependent on the their consistency. In addition, molybdenum disulfide (MoS 2 ) as a libricant additive shows strong absorption from 0.2 to 1.4 THz, leading to higher absorption of MoS 2 -lithium grease than that of lithium grease. (general)

New technologies in Islamic countries. Power engineering, transport, oil industry, machinery construction, building construction and information technologies problems

International Nuclear Information System (INIS)

Sharipova, N.S.

1999-01-01

The published proceedings contain brief presentations concerning new technologies in power engineering, transport, oil industry, machinery construction, building construction and information technologies presented to the International scientific and technical conference: New technologies in Islamic countries, which was organized within frame work of 6 General Assembly of Federation of engineering Institutes of Islamic countries (FEIIC). (author)

Evaluation of physical and chemical properties and their interactions in fat, oil, and grease (FOG) deposits.

Science.gov (United States)

Gross, Martin A; Jensen, Jeanette L; Gracz, Hanna S; Dancer, Jens; Keener, Kevin M

2017-10-15

Fat, oil and grease (FOG) blockages in sewer systems are a substantial problem in the United States. It has been estimated that over 50% of sewer overflows are a result of FOG blockages. In this work, a thorough laboratory study was undertaken to examine key variables that contribute to FOG deposit formation under controlled conditions. Physical and chemical properties and their interactions were evaluated and conditions that generated deposits that mimicked field FOG deposits were identified. It was found that 96 of the of 128 reaction conditions tested in the laboratory formed FOG deposits with similar physical and chemical characteristics as field FOG deposits. It was also found that FOG deposits can be created through fatty acid crystallization and not just saponification. Furthermore FOG deposits were found to be more complex than previously documented and contain free fatty acids, fatty acid metal salts, triacylglycerol's, diacylglycerol's and, monoacylglycerol's. Lastly it was found that FOG deposits that only contained saturated fatty acids were on average 2.1 times higher yield strength than deposits that contained unsaturated fatty acids. Copyright © 2017 Elsevier Ltd. All rights reserved.

New technologies in Islamic countries. Power engineering, transport, oil industry, machinery construction, building construction and information technologies problems

International Nuclear Information System (INIS)

Sharipova, N.S.

1999-01-01

This issue contains papers, which reflect the most important achievements of new technologies in power engineering, transport, oil industry, machinery construction, building construction and information technologies presented to the International Scientific and Technical Conference: New technologies in Islamic countries, which was organized within frame work of 6 General Assembly of Federation of Engineering Institutes of Islamic Countries (FEIIC). (author)

Detection of Elemental Composition of Lubricating Grease Using Laser Induced Breakdown Spectroscopy

Directory of Open Access Journals (Sweden)

Cherry Dhiman

2014-12-01

Full Text Available The elemental composition of lubricating soft grease used in rail engines are studied using laser induced breakdown spectroscopy (LIBS technique. LIBS spectra of fresh, partially used and fully used grease samples are recorded using time-gated ICCD spectrometer for verification of compositional degradation of the used grease. LIBS spectra of grease samples are analyzed by comparing with emission spectra of elements published by NIST standard database. Many spectral lines of impurity elements like Fe, Cu, Ba, Mg, Mn, Ni, S, Zn, Si, Pb, Ti, Ca and Al present in the grease in ppm or ppb level in trace level concentrations are observed in excess in the used grease mainly due to wear and tear. On the other hand in fresh grease, spectral lines of Ca, Al and Na are observed predominantly.

Assessment of the impact of oil spill on Mumbai harbor bay

International Nuclear Information System (INIS)

Pandit, G.G.; Saradhi, I.V.; Puranik, V.D.; Sharma, D.N.; Ghosh, A.K.

2011-04-01

On 7 th August, 2010 two cargo ships MSC Chitra and MV Khalijia collided off Mumbai coast causing an oil spill that spread quickly through Maharashtra's coastline. MSC Chitra ruptured its tank when it hit incoming MV Khalijia. MSC Chitra tilted to about 80 degrees soon after the collision, spilling an estimated 400 to 500 tonnes of oil. The ship was loaded with an estimated 2,600 tonnes of oil, 300 tonnes of diesel and 70 tonnes of lubricating oil at the time of the accident. The oil spill has spreaded over an area of 25 square kilometers. MSC Chitra was carrying 1219 containers out of which 31 had hazardous chemicals like organophosphate pesticides. After the collision about 400 containers fall off into to the sea from the deck of MSC Chitra. The oil spill has resulted in severe environmental damage along the Mumbai coastline as well as to the marine life. In order to assess the impact of oil spill on the marine environment daily monitoring of oil and grease levels has been carried out at CIRUS Jetty. Additionally three field surveys have been carried out along the coast line of Mumbai harbor bay from Vashi Jetty to Uran collecting sea water samples. The samples collected at CIRUS Jetty and Mumbai harbor bay are analyzed for various water quality parameters apart from oil and grease. The results indicate the oil and grease levels in sea water at CIRUS Jetty reduced to background levels within 15 days. The filed survey along Mumbai harbor bay also shows a decreasing trend in the oil and grease levels in seawater. (author)

Development of high performance lubricant through the compatibility of polyalphaolefin, polyurea and irradiated polytetrafluoroethylene; Graxa de poliureia: estudo da compatibilidade da poliureia, polialfaolefina e politetrafluoretileno irradiado para melhoria da lubricidade e estabilidade

Energy Technology Data Exchange (ETDEWEB)

Ratao, Natalia Torres

2013-07-01

Lubricants are gaseous, liquid, semi solid or solid (powder) materials those form a film between two parties preventing friction. High performance lubricants are designed to work under severe conditions of temperature, pressure, and contamination. The most used are liquids (oils) and semi solids (greases). Greases are applied where oils can drain or in inaccessible places and are divided generally into two classes, soap and no soap. The most used non soap grease is polyurea, obtained by the reaction between amine and isocyanate, has highly thixotropic, high dielectric strength and excellent anticorrosive property, so it is widely used for lubrication of electric motors and shipbuilding machinery. For a grease with high performance, in this study was used a synthetic lubricant fluid, polyalphaolefin, and was also employed solid lubricant additive polytetrafluoroethylene (PTFE) due its lowest coefficient of friction, is found commercially irradiated in air to obtain smaller particles and to produce oxygenated terminal groups those are more compatible with the metal surface. The tests conducted were comparatively between pure polyurea grease and with PTFE additive. The characterizations were made by infrared spectroscopy and elemental analysis of C, N and H and Free NCO index, proving the formation of four carbons polyurea (tetraurea). The functional analysis of drop point and oil separation showed high stability and compatibility between the polymers increased when PTFE was added. The excellent resistance of pure tetraurea grease to wear and extreme pressure were demonstrated by four-ball and practical bearings tests, characterizing this grease as a high performance lubricant, when compared to most used greases in the market. (author)

Development of high performance lubricant through the compatibility of polyalphaolefin, polyurea and irradiated polytetrafluoroethylene

International Nuclear Information System (INIS)

Ratao, Natalia Torres

2013-01-01

Lubricants are gaseous, liquid, semi solid or solid (powder) materials those form a film between two parties preventing friction. High performance lubricants are designed to work under severe conditions of temperature, pressure, and contamination. The most used are liquids (oils) and semi solids (greases). Greases are applied where oils can drain or in inaccessible places and are divided generally into two classes, soap and no soap. The most used non soap grease is polyurea, obtained by the reaction between amine and isocyanate, has highly thixotropic, high dielectric strength and excellent anticorrosive property, so it is widely used for lubrication of electric motors and shipbuilding machinery. For a grease with high performance, in this study was used a synthetic lubricant fluid, polyalphaolefin, and was also employed solid lubricant additive polytetrafluoroethylene (PTFE) due its lowest coefficient of friction, is found commercially irradiated in air to obtain smaller particles and to produce oxygenated terminal groups those are more compatible with the metal surface. The tests conducted were comparatively between pure polyurea grease and with PTFE additive. The characterizations were made by infrared spectroscopy and elemental analysis of C, N and H and Free NCO index, proving the formation of four carbons polyurea (tetraurea). The functional analysis of drop point and oil separation showed high stability and compatibility between the polymers increased when PTFE was added. The excellent resistance of pure tetraurea grease to wear and extreme pressure were demonstrated by four-ball and practical bearings tests, characterizing this grease as a high performance lubricant, when compared to most used greases in the market. (author)

Fluorescence excitation-emission matrix spectroscopy for degradation monitoring of machinery lubricants

Science.gov (United States)

Sosnovski, Oleg; Suresh, Pooja; Dudelzak, Alexander E.; Green, Benjamin

2018-02-01

Lubrication oil is a vital component of heavy rotating machinery defining the machine's health, operational safety and effectiveness. Recently, the focus has been on developing sensors that provide real-time/online monitoring of oil condition/lubricity. Industrial practices and standards for assessing oil condition involve various analytical methods. Most these techniques are unsuitable for online applications. The paper presents the results of studying degradation of antioxidant additives in machinery lubricants using Fluorescence Excitation-Emission Matrix (EEM) Spectroscopy and Machine Learning techniques. EEM Spectroscopy is capable of rapid and even standoff sensing; it is potentially applicable to real-time online monitoring.

Effect of carbonyl iron particles composition on the physical characteristics of MR grease

Energy Technology Data Exchange (ETDEWEB)

Mohamad, Norzilawati, E-mail: mnorzilawati@gmail.com; Mazlan, Saiful Amri, E-mail: amri.kl@utm.my [Vehicle System Engineering, Malaysia – Japan International Institute of Technology, Universiti Teknologi Malaysia, Jalan Sultan Yahya Petra (Jalan Semarak), Kuala Lumpur, 54000 (Malaysia); Ubaidillah, E-mail: ubaidillah@uns.ac.id [Vehicle System Engineering, Malaysia – Japan International Institute of Technology, Universiti Teknologi Malaysia, Jalan Sultan Yahya Petra (Jalan Semarak), Kuala Lumpur, 54000 (Malaysia); Mechanical Engineering Department, Faculty of Engineering, Universitas Sebelas Maret, Jl. Ir. Sutami 36A, Kentingan, Surakarta, 57126, Central Java, Surakarta (Indonesia)

2016-03-29

Magnetorheological (MR) grease is an extension of the study of magnetorheological materials. The MR grease can help to reduce the particles sedimentation problem occurred in the MR fluids. Within this study, an effort has been taken to investigate the effect of different weight compositions of carbonyl iron particles on the physical and chemical characteristics of the MR grease under off-state condition (no magnetic field). The MR grease is prepared by mixing carbonyl iron particles having a size range of 1 to 10 µm with commercial NPC Highrex HD-3 grease. Characterizations of MR grease are investigated using Vibrating Sample Magnetometer (VSM), Environmental Scanning Electron Microscopy (ESEM), Differential Scanning Calorimeter (DSC) and rheometer. The dependency of carbonyl iron particles weight towards the magnetic properties of MR grease and other characterizations are investigated.

Brown Grease to Biodiesel Demonstration Project Report

Energy Technology Data Exchange (ETDEWEB)

San Francisco Public Utilities Commission; URS Corporation; Biofuels, Blackgold; Carollo Engineers

2013-01-30

Municipal wastewater treatment facilities have typically been limited to the role of accepting wastewater, treating it to required levels, and disposing of its treatment residuals. However, a new view is emerging which includes wastewater treatment facilities as regional resource recovery centers. This view is a direct result of increasingly stringent regulations, concerns over energy use, carbon footprint, and worldwide depletion of fossil fuel resources. Resources in wastewater include chemical and thermal energy, as well as nutrients, and water. A waste stream such as residual grease, which concentrates in the drainage from restaurants (referred to as Trap Waste), is a good example of a resource with an energy content that can be recovered for beneficial reuse. If left in wastewater, grease accumulates inside of the wastewater collection system and can lead to increased corrosion and pipe blockages that can cause wastewater overflows. Also, grease in wastewater that arrives at the treatment facility can impair the operation of preliminary treatment equipment and is only partly removed in the primary treatment process. In addition, residual grease increases the demand in treatment materials such as oxygen in the secondary treatment process. When disposed of in landfills, grease is likely to undergo anaerobic decay prior to landfill capping, resulting in the atmospheric release of methane, a greenhouse gas (GHG). This research project was therefore conceptualized and implemented by the San Francisco Public Utilities Commission (SFPUC) to test the feasibility of energy recovery from Trap Waste in the form of Biodiesel or Methane gas. The research goals are given below: To validate technology performance; To determine the costs and benefits [including economic, socioeconomic, and GHG emissions reduction] associated with co-locating this type of operation at a municipal wastewater treatment plant (WWTP); To develop a business case or model for replication of the

Research on a lubricating grease print process for cylindrical cylinder

Science.gov (United States)

Yang, Liu; Zhang, Xuan; Wang, XianYan; Tan, XiaoYan

2017-09-01

In vehicle braking system and clutch system of transmission, there is always a kind of cylindrical component dose reciprocating motion. The main working method is the reciprocating motion between the rubber sealing parts and cylindrical parts, the main factor affects the service life of the product is the lubricating performance of the moving parts. So the lubricating performance between cylinders and rubber sealing rings is particularly important, same as the quality of the grease applies on the surface of the surface of cylinder. Traditional method of manually applying grease has some defects such as applying unevenly, applying tools like brush and cloth easily falls off and affect the cleanness of products, contact skin easily cause allergy, waste grease due to the uncontrollable of grease quantity using in applying, low efficiency of manual operation. An automatic, quantitative and high pressure applying equipment is introduced in this document to replace the traditional manually applying method, which can guarantee the applying quality of the grease which are painted on the surface of cylinder and bring economic benefits to the company.

Lubricating grease shear flow and boundary layers in a concentric cylinder configuration

NARCIS (Netherlands)

Li, J.X.; Westerberg, L.G.; Höglund, E.; Lugt, Pieter Martin; Baart, P.

2014-01-01

Grease is extensively used to lubricate various machine elements such as rolling bearings, seals, and gears. Understanding the flow dynamics of grease is relevant for the prediction of grease distribution for optimum lubrication and for the migration of wear and contaminant particles. In this study,

Impact of Water on the Rheology of Lubricating Greases

NARCIS (Netherlands)

Cyriac, F.; Lugt, Pieter Martin; Bosman, Rob

2016-01-01

The operational life of bearings is often determined by the performance of the lubricating grease. The consistency of the grease prevents it from leaking out of the bearing and provides good sealing properties. The possible ingress of water into the bearing will have a considerable impact not only

Accumulation of oil and grease in soils irrigated with greywater and their potential role in soil water repellency.

Science.gov (United States)

Travis, Micheal J; Weisbrod, Noam; Gross, Amit

2008-05-01

The potential impact of oil and grease (O and G) to soils irrigated with greywater (GW) was investigated. Greywater streams were sampled and analyzed for O and G content, along with corresponding GW-irrigated soils. Untreated kitchen GW averaged 200 mg L(-1) O and G, over an order of magnitude more than other GW streams. GW-irrigated soils showed O and G accumulation of up to 200 mg kg(-l) within the first 20-cm of depth. To determine the potential effects of such O and G accumulation on water movement in soil, capillary rise and water drop penetration time (WDPT) experiments were conducted. The results showed up to 60% decrease in capillary rise when sand containing 250 mg kg(-1) O and G was used. Interestingly, no additional reduction in capillary rise was observed at concentrations above 250 mg kg(-1). WDPT was observed to increase linearly with increased O and G content, up to 1000 mg kg(-1). This work demonstrated that O and G in GW used for irrigation can accumulate in soil and may lead to a significant reduction in the soils ability to transmit water.

Abnormal vibration of turbine due to oil whip

International Nuclear Information System (INIS)

Koo, Jae Raeyang; Hwang, Jae Hyeon

2001-01-01

Almost all rotating machinery has bearings. Bearing is one of the most important part of rotating machinery. Vibration of rotating machinery depend on its bearing conditions. Bearing conditions are following; oil gap, bearing type, bearing temperature, bearing oil condition. Especially, bearing oil condition influences on rotating machinery vibration directly. In this paper we have discussed the abnormal vibration of turbine due to oil condition. Oil whip problem was occurred in the certain power plant and we had solved this problem through the control of operating values and alignment

Short Communication - Aquatic Oil Pollution Impact Indicators ...

African Journals Online (AJOL)

Aquatic oil pollution impact indicators such as oil-grease, low dissolved oxygen concentration, increased biochemical oxygen demand, increased water temperature and acidity of the water are associated with aquatic habitat degradation, reduced productivity and or loss of biodiversity. These impact indicators are ...

A full-scale UASB reactor for treatment of pig and cattle slaughterhouse wastewater with a high oil and grease content

Directory of Open Access Journals (Sweden)

L. A. S. Miranda

2005-12-01

Full Text Available This paper discusses the performance of an 800m³ full-scale UASB reactor in treating meat-packing plant and slaughterhouse effluents containing high concentrations of oil and grease (O&G (413-645 mg/L, resulting in a COD/O&G ratio of 26-32%. Those macromolecules were considered responsible for the unbalance of the system resulting in a total washout of the biomass. The removal of O&G from the influent using a physicochemical system (coagulation-flocculation improved the physical characteristics of the anaerobic sludge, controlling the biomass washout. Reactor performance was significantly improved when the COD/O&G ratio influent was maintained in the 10%. The COD and O&G removal rates obtained after implantation of the physicochemical system were 70-92% and 27-58%, respectively. The specific methanogenic activity (SMA of the biomass shows towards a tendency stabilisation and adaptation to the substrate influent. Pretreatment of the influent allowed the maximum organic load to be increased (1.46 to 2.43 Kg COD/m³.d and improved the quality of the effluent.

Oil and grease (O&G removal from commercial kitchen waste water using carbonised grass as a key media

Directory of Open Access Journals (Sweden)

Rahmat Siti Nazahiyah

2017-01-01

Full Text Available Oil and grease (O&G are usually found in kitchen waste water. O&G are poorly soluble in water and can cause serious problems during the wastewater treatment. Adsorption is a fundamental process in the treatment of kitchen waste water and very economical. Activated carbon is the most effective adsorbent for this application. Therefore, the aim of the current study is to determine the potential of four materials (i.e. sand, gravel, carbonised grass (CG and clay powder as filter media for O&G removal. The CGs were originated from “Elephant Grass” and it is a fast growing plant with significant potential as carbon. The clay acts as a magnet, drawing the oil molecules out of the water and causing them to attach to the surfaces of the clay. In the current study, two filters were developed with different media materials to get the best percentage removal. Filters 1 and 2 were filled with sand, gravel and CG, and sand, gravel, CG and powder clay, respectively. Three samples were taken during peak hour between April and May 2016. The initial O&G concentration varied from 101.37 mg/l to 248.30 mg/l and the final concentration varied from none to 22.57 mg/l for both filters. The percentage removal (% of O&G were between 90.9 and 97.3 (Filter 1 and between 94.3 and 100 (Filter 2. Overall, both filters could efficiently remove O&G in the waste water and the quality of the carbonised grass proved to be as good as carbon produced from other traditional sources.

Evaluating and modeling biogas production from municipal fat, oil, and grease and synthetic kitchen waste in anaerobic co-digestions.

Science.gov (United States)

Li, Chenxi; Champagne, Pascale; Anderson, Bruce C

2011-10-01

The feasibility of using synthetic kitchen waste (KW) and fat, oil, and grease (FOG) as co-substrates in the anaerobic digestion of waste activated sludge (WAS) was investigated using two series of biochemical methane potential (BMP) tests. Ranges of ideal substrate to inoculum (S/I) ratio were determined for the FOG (0.25-0.75) and KW (0.80-1.26) as single substrates in the first experiment. The second experiment, which estimated the methane production performances of FOG and KW as co-substrates for WAS co-digestion, was conducted based on the optimal parameters selected from the results of the first experiment. Results indicated that co-digestions with FOG and KW enhanced methane production from 117±2.02 mL/gTVS (with only WAS) to 418±13.7 mL/gTVS and 324±4.11 mL/gTVS, respectively. FOG exhibited more biogas production than KW as co-substrate. Non-linear regression results showed that co-substrate addition shortened the lag phases of organic biodegradation from 81.8 (with only WAS) to 28.3 h with FOG and 3.90 h with KW. Copyright © 2011 Elsevier Ltd. All rights reserved.

Characterisation of FOGs in grease trap waste from the processing of chickens in Thailand.

Science.gov (United States)

Nitayapat, Nuttakan; Chitprasert, Pakamon

2014-06-01

Industrial firms that kill and process chickens generate wastewater that contains fat, oil, and grease (FOG). The FOGs are located in the fatty waste that is collected by floatation in grease traps. Chemical and physical characterisation of FOGs would provide useful information that would help in the development of methods designed to decrease the extent of pollution caused by disposal of the waste and to utilise commercially some of its lipid constituents. Employing these methods would enhance the profitability and competitive potential of these commercial organisations. Samples of grease trap waste from 14 firms in central Thailand have been examined. Due to the very different schemes of waste management employed by these firms, the physical appearance of their fatty wastes showed considerable variation. The chemical and physical properties of the FOGs present in these wastes showed considerable variation also. Large amounts of free fatty acids (10-70% as oleic acid) were detected in most of the 14 wastes and palmitic, cis-9-oleic, cis,cis-9,12-linoleic, stearic, and palmitoleic acids were the predominant species of free and esterified acids. Most of the FOGs were solid at temperatures below 40 °C. Many of them contained traces of heavy metals (Cu and Pb) and some contained traces of the pesticides dimethoate and cypermethrin. The content of these potentially hazardous substances would have to be considered very carefully before discarding the fatty wastes and during the development of methods designed to isolate their potentially profitable lipid constituents. Copyright © 2013 Elsevier Ltd. All rights reserved.

Physicochemical Characteristics and Microbial Quality of an Oil ...

African Journals Online (AJOL)

kg and the lowest value from the river shore sand (620) mg/kg. The high level of oil and grease contamination poses a concern. This therefore, validates the concern that releases of large quantities of oil to aquatic and terrestrial environments ...

Evaluation of different polyolefins as rheology modifier additives in lubricating grease formulations

Energy Technology Data Exchange (ETDEWEB)

Martin-Alfonso, J.E.; Valencia, C.; Sanchez, M.C. [Departamento de Ingenieria Quimica, Facultad de Ciencias Experimentales, Universidad de Huelva, Campus Universitario del Carmen, 21071 Huelva (Spain); Franco, J.M., E-mail: franco@uhu.es [Departamento de Ingenieria Quimica, Facultad de Ciencias Experimentales, Universidad de Huelva, Campus Universitario del Carmen, 21071 Huelva (Spain); Gallegos, C. [Departamento de Ingenieria Quimica, Facultad de Ciencias Experimentales, Universidad de Huelva, Campus Universitario del Carmen, 21071 Huelva (Spain)

2011-08-15

Highlights: {yields} Evaluation of different polyolefins as modifiers of the rheological properties and mechanical stability of lithium lubricating greases. {yields} The type of polymer, molecular weight, cristallinity degree and vinyl acetate content influences the rheological and thermal response of lubricating greases. {yields} The crystallinity degree, mainly dependent on the nature of the polymer, is the most highly influencing parameter on the rheology of lubricating greases. {yields} The rheological modification exerted by EVA copolymers mainly depends on the vinyl acetate content. - Abstract: The purpose of the present work is to evaluate the effect that different polyolefins, used as additives in small proportions, exert on the rheological properties of standard lithium lubricating greases. Grease formulations containing several polyolefins, differing in nature and molecular weight, were manufactured and rheologically characterized. The influence of the type of polymer, molecular weight, crystallinity degree and vinyl acetate content has been analyzed. Small-amplitude oscillatory shear (SAOS) and viscous flow measurements, as well as calorimetric (DSC) and thermogravimetric (TGA) analysis, were carried out. In general, the addition of polymers such as HDPE, LDPE, LLDPE and PP to lithium lubricating greases significantly increases the values of the rheological parameters analyzed, consistency and mechanical stability. However, the use of polyolefins as rheology modifiers does not significantly affect the friction coefficient determined in a tribological contact. The crystallinity degree, mainly dependent on the nature of the polymer, has been found the most highly influencing parameter on the rheology of the lubricating greases studied. However, the rheological modification exerted by EVA copolymers mainly depends on the vinyl acetate content. Thus, a negative effect in both apparent viscosity and linear viscoelastic functions of greases was obtained when

San Francisco Biofuel Program: Brown Grease to Biodiesel Demonstration

Energy Technology Data Exchange (ETDEWEB)

Jolis, Domènec [San Francisco Public Utilities Commission, San Francisco, CA (United States); Martis, Mary [San Francisco Public Utilities Commission, San Francisco, CA (United States); Jones, Bonnie [San Francisco Public Utilities Commission, San Francisco, CA (United States); Miot, Alex [San Francisco Public Utilities Commission, San Francisco, CA (United States); Ving, Karri [San Francisco Public Utilities Commission, San Francisco, CA (United States); Sierra, Natalie [San Francisco Public Utilities Commission, San Francisco, CA (United States); Niobi, Morayo [San Francisco Public Utilities Commission, San Francisco, CA (United States)

2013-03-01

Municipal wastewater treatment facilities have typically been limited to the role of accepting wastewater, treating it to required levels, and disposing of its treatment residuals. However, a new view is emerging which includes wastewater treatment facilities as regional resource recovery centers. This view is a direct result of increasingly stringent regulations, concerns over energy use, carbon footprint, and worldwide depletion of fossil fuel resources. Resources in wastewater include chemical and thermal energy, as well as nutrients, and water. A waste stream such as residual grease, which concentrates in the drainage from restaurants (referred to as Trap Waste), is a good example of a resource with an energy content that can be recovered for beneficial reuse. If left in wastewater, grease accumulates inside of the wastewater collection system and can lead to increased corrosion and pipe blockages that can cause wastewater overflows. Also, grease in wastewater that arrives at the treatment facility can impair the operation of preliminary treatment equipment and is only partly removed in the primary treatment process. In addition, residual grease increases the demand in treatment materials such as oxygen in the secondary treatment process. When disposed of in landfills, grease is likely to undergo anaerobic decay prior to landfill capping, resulting in the atmospheric release of methane, a greenhouse gas (GHG). This research project was therefore conceptualized and implemented by the San Francisco Public Utilities Commission (SFPUC) to test the feasibility of energy recovery from Trap Waste in the form of Biodiesel or Methane gas.

Some azine and azole derivatives as antioxidant additives for lithium lubricating grease

Directory of Open Access Journals (Sweden)

Reda M. Fikry

2013-06-01

The structure of these compounds has been confirmed using elemental analysis, nuclear magnetic resonance and infrared spectroscopy. On the other hand, lithium lubricating grease was prepared and evaluated according to the National Lubricating Grease Institute (NLGI and Egyptian Standard (ES. The antioxidant compounds were tested for the prepared grease with concentration 0.1 wt.%. The efficiency of these compounds has been determined using total acid number. It was found that the prepared lithium grease resists oxidation reaction in the presence of these compounds. A correlation between the chemical structure of these compounds and their efficiency as antioxidants additives was discussed. Data showed that the efficiency of these compounds as antioxidants decreases in the order: compound I > compound II > compound III.

The Impact of Water on the Yield Stress and Startup Torque of Lubricating Greases

NARCIS (Netherlands)

Cyriac, F.; Lugt, Pieter Martin; Bosman, Rob

2017-01-01

Water is one of the most common contaminants in grease lubrication. There are numerous applications where bearings are susceptible to water ingresses such as in the steel, food, and pulp and paper industries. A grease can absorb water to different degrees depending upon the type of grease. The

Organic pollutant removal from edible oil process wastewater using electrocoagulation

Science.gov (United States)

Sharma, S.; Can, O. T.; Hammed, M.; Nawarathna, D.; Simsek, H.

2018-03-01

Wastewaters generated from vegetable oil industries contain a high concentration of organic pollutants that are detrimental to the aquatic ecosystem. Electrochemical processes are gaining importance in the treatment of inorganic and resistant organic pollutants in wastewaters. In this study, electrocoagulation (EC) was applied to remove organic pollutants and oil and grease from canola oil wastewater using aluminum (Al) and iron (Fe) electrodes. The application of EC in the wastewater achieved more than 80% removal of organic carbon and nearly 100% removal of suspended solids (SS). The effectiveness of EC is influenced mainly by current density, pH, electrolyte (NaCl), electrode contact time and electrode type. It was observed that Al electrode combination yielded better removal at a lesser time compared to that of Fe electrodes. However, varying current densities had its significance in terms of coagulation time only. Increase in current density achieved decrease in coagulation time. Both Al and Fe could remove between 52-59% of oil and grease from canola oil wastewater

BAURAN PEMASARAN PRODUK BARU PELUMAS FOOD GRADE GREASE BERBAHAN DaSAR MINYAK SAWIT

Directory of Open Access Journals (Sweden)

Ali Maksum

2016-12-01

Full Text Available Grease with food grade specification is essentially required on food processing production activities.  The purpose of this study is to develop a new product marketing mix for food grade grease, i.e 1 product priority, 2 pricing priority, 3 distribution priority and 4 advertising priority. This Research was conducted in Sub District Purbalingga and Padamara, Purbalingga regency with respondent SMEs food processing. Analysis of the determination of marketing mix that includes product, price, advertising and distribution using the Analytical Hierarchy Process (AHP. Sampling was purposive random sampling method with a population of 64 SMEs so drawn sample of 20 respondents. Result of the study showed the marketing mix priority which were: (1 advertising priority for the new food grade grease product with an ads that could attract the attention of consumers in order to made the consumers interested, tried, and bought the new food grade lubricating grease products. (2 Price priority for the new food grade grease products which was by determining the moderate prices to compete the competitors' prices while still maintained a high quality. (3 Product priority for new food grade grease product which was producing a qualified product which could withstand the wear of the engine, green colour of the product, a 350 g size packs with a rectangular shape packaging labels. (4 Distribution priority for the new food grade grease product which was a short distribution channels through mobile vendors so that the consumers were able to save costs, and got the product fast and easily

40 CFR 112.11 - Spill Prevention, Control, and Countermeasure Plan requirements for offshore oil drilling...

Science.gov (United States)

2010-07-01

... POLLUTION PREVENTION Requirements for Petroleum Oils and Non-Petroleum Oils, Except Animal Fats and Oils and Greases, and Fish and Marine Mammal Oils; and Vegetable Oils (Including Oils from Seeds, Nuts, Fruits, and... equipped with dump valves which predominantly fail in the closed position and where pollution risk is high...

A Survey on the Removal Efficiency of Fat, Oil and Grease in Shiraz Municipal Wastewater Treatment Plant

Directory of Open Access Journals (Sweden)

Dehghani

2014-12-01

Full Text Available Background Fat, oil and grease (FOG in municipal wastewater treatment plant (MWWTP caused many problems. Objectives This study aimed to determine the removal efficiency of FOG in Shiraz MWWTP. Materials and Methods The removal efficiencies of FOG in the MWWTP were studied from June 2011 to September 2011 in Shiraz (Iran. The influent and effluent wastewater samples were collected in a volume of one liter (4 samples per week and analyzed according to the standard methods. Samples are transferred to the laboratory immediately. The concentration of FOG was determined using the solvent extraction and separating funnel and then compared with the effluent standards. To analyze the data, SPSS (version 11.5, Chi-square test and t test were used. Results The results showed that the FOG amount in input raw sewage in the MWWTP from June 2011 to September 2011 was around 25.5 mg/L and the amount in treated wastewater was about 8.1 mg/L. The FOG removal efficiency in this refinery was about 70% and met the environmental standards for the discharge (less than 10 mg/L (P < 0.05. Conclusions The effluent can be discharged to surface waters or used for irrigation. In order to the FOG concentration met the effluent standards, it is very crucial to control the entrance of industrial wastewater to the municipal wastewater collection networks. Otherwise, the MWWTP should be upgraded and the special techniques used to reduce FOG.

The Field-Dependent Rheological Properties of Magnetorheological Grease Based on Carbonyl-Iron-Particles

Science.gov (United States)

Mohamad, N.; Mazlan, S. A.; Ubaidillah; Choi, Seung-Bok; Nordin, M. F. M.

2016-09-01

This paper presents dynamic viscoelastic properties of magnetorheological (MR) grease under variation of magnetic fields and magnetic particle fractions. The tests to discern the field-dependent properties are undertaken using both rotational and oscillatory shear rheometers. As a first step, the MR grease is developed by dispersing the carbonyl iron (CI) particles into grease medium with a mechanical stirrer. Experimental data are obtained by changing the magnetic field from 0 to 0.7 T at room temperature of 25 °C. It is found that a strong Payne effect limits the linear viscoelastic region of MR grease at strains above 0.1%. The results exhibit a high dynamic yield stress which is equivalent to Bingham plastic rheological model, and show relatively good MR effect at high shear rate of 2000 s-1. In addition, high dispersion of the magnetic particles and good thermal properties are proven. The results presented in this work directly indicate that MR grease is a smart material candidate that could be widely applicable to various fields including vibration control.

Study on thermal effects & sulfurized additives, in lubricating greases

Science.gov (United States)

Shah, Ami Atul

Lithium Base grease constitutes about 50% of market. The greases are developed to be able to work in multiple working conditions and have longer working life. Greases with extreme pressure additives and anti-wear additives have been developed as a solution to many of the applications. These developed greases are tested under ASTM D2266 testing conditions to meet the requirements. The actual working conditions, although, differ than the real testing conditions. The loading, speed and temperature conditions can be more harsh, or fluctuating in nature. The cyclic nature of the parameters cannot be directly related to the test performance. For this purpose studies on the performance under spectrum loading, variable speed and fluctuating temperature must be performed. This study includes tests to understand the effect of thermal variation on some of the most commonly used grease additives that perform well under ASTM D2266 testing conditions. The studied additives include most widely used industrial extreme pressure additive MoS2. Performance of ZDDP which is trying to replace MoS2 in its industrial applications has also been studied. The tests cover study of extreme pressure, anti-wear and friction modifier additives to get a general idea on the effects of thermal variation in three areas. Sulphur is the most common extreme pressure additive. Sulphur based MoS 2 is extensively used grease additive. Study to understand the tribological performance of this additive through wear testing and SEM/EDX studies has been done. This performance is also studied for other metallic sulfides like WS2 and sulphur based organic compound. The aim is to study the importance of the type of bond that sulphur shares in its additive's structure on its performance. The MoS2 film formation is found to be on the basis of the FeS formation on the substrate and protection through sacrificial monolayer deposition of the MoS2 sheared structure. The free Mo then tends to oxidise. An attempt to

Rheological Behavior of Carbon Nanotubes as an Additive on Lithium Grease

Directory of Open Access Journals (Sweden)

Alaa Mohamed

2013-01-01

Full Text Available The rheological behaviors of carbon nanotubes (CNTs as an additive on lithium grease at different concentrations were examined under various settings of shear rate, shear stress, and apparent viscosity. The results indicated that the optimum content of the CNTs was 2%. These experimental investigations were evaluated with a Brookfield Programmable Rheometer DV-III ULTRA. The results indicated that the shear, stress and apparent viscosity increase with the increase of CNTs concentration. The microstructure of CNTs and lithium grease was examined by high resolution transmission electron microscope (HRTEM and scanning electron microscope (SEM. The results indicated that the microscopic structure of the lithium grease presents a more regular and homogeneous network structure, with long fibers, which confirms the rheological stability.

Bioremediation of oil contaminated soils

International Nuclear Information System (INIS)

Beeson, D.L.; Hogue, J.I.; Peterson, J.C.; Guerra, G.W.

1994-01-01

The Baldwin Waste Oil Site was an abandoned waste oil recycling facility located in Robstown, Nueces County, Texas. As part of their site assessment activities, the US Environmental Protection Agency (EPA) requested that the Ecology and Environment, Inc., Technical Assistance Team (TAT) investigate the feasibility of using in-situ bioremediation to remediate soils contaminated with oil and grease components, petroleum hydrocarbons, and volatile organic compounds. Bioremediation based on the land treatment concept was tested. The land treatment concept uses techniques to optimize indigenous microbial populations and bring them in contact with the contaminants. The study was designed to collect data upon which to base conclusions on the effectiveness of bioremediation, to demonstrate the effectiveness of bioremediation under field conditions, and to identify potential problems in implementing a full-scale project. Bioremediation effectiveness was monitored through total petroleum hydrocarbons (TPH) and Oil and Grease (O and G) analyses. Site specific treatment goals for the pilot project were concentrations of less than 1% for O and G and less than 10,000 mg/kg for TPH. Based on the reduction of TPH and O and G concentrations and the cost effectiveness of bioremediation based on the land treatment concept, full-scale in-situ bioremediation was initiated by the EPA at the Baldwin Waste Oil Site in February of 1993

Opportunities for Biorenewables in Oil Refineries

Energy Technology Data Exchange (ETDEWEB)

Marker, T.L.

2005-12-19

Abstract: The purpose of this study was to evaluate the potential for using biorenewable feedstocks in oil refineries. Economic analyses were conducted, with support from process modeling and proof of principle experiments, to assess a variety of potential processes and configurations. The study considered two primary alternatives: the production of biodiesel and green diesel from vegetable oils and greases and opportunities for utilization of pyrolysis oil. The study identified a number of promising opportunities for biorenewables in existing or new refining operations.

Friction torque in thrust ball bearings grease lubricated

Science.gov (United States)

Ianuş, G.; Dumitraşcu, A. C.; Cârlescu, V.; Olaru, D. N.

2016-08-01

The authors investigated experimentally and theoretically the friction torque in a modified thrust ball bearing having only 3 balls operating at low axial load and lubricated with NGLI-00 and NGLI-2 greases. The experiments were made by using spin-down methodology and the results were compared with the theoretical values based on Biboulet&Houpert's rolling friction equations. Also, the results were compared with the theoretical values obtained with SKF friction model adapted for 3 balls. A very good correlation between experiments and Biboulet_&_Houpert's predicted results was obtained for the two greases. Also was observed that the theoretical values for the friction torque calculated with SKF model adapted for a thrust ball bearing having only 3 balls are smaller that the experimental values.

The potential of restaurant trap grease as biodiesel feedstock

Directory of Open Access Journals (Sweden)

Parichart Hasuntree

2011-10-01

Full Text Available The possibility of using restaurant trap grease as feedstock in the production of biodiesel via acid catalyzed esterificationis explored in this study. Sulfuric acid was used as a catalyst for the esterification reaction of free fatty acid (FFA andmethanol. The FFA levels of restaurant trap greases were reduced from 60.38±2.22 mg KOH/g to 11.60±1.60 mgKOH/g whenconditions for biodiesel production are as follow: methanol-to-FFA ratio of 5:1, 5 wt.% H2SO4, and a reaction temperature at60°C with a reaction time of 60 min. During the acid-catalyzed esterification, the percentage of methyl esters resulting fromconversion of FFA in the obtained product was 83.59±1.51% based on the result of 1H NMR analysis. Data obtained from the23 full factorial designs revealed that methanol-to-FFA ratio term had the most significant effect on the percentage of methylesters, followed by the H2SO4 concentration. Conversely, reaction time between 1 and 3 hours had no significant effect on theesterification of trap greases.

Rheological Behavior of Carbon Nano tubes as an Additive on Lithium Grease

International Nuclear Information System (INIS)

Mohamed, A.; Zaki, M.; Mohamed, A.; Khattab, A.A.; Osman, T.A.

2013-01-01

The rheological behaviors of carbon nano tubes (CNTs) as an additive on lithium grease at different concentrations were examined under various settings of shear rate, shear stress, and apparent viscosity. The results indicated that the optimum content of the CNTs was 2%. These experimental investigations were evaluated with a Brookfield Programmable Rheometer DV-III ULTRA. The results indicated that the shear, stress and apparent viscosity increase with the increase of CNTs concentration. The microstructure of CNTs and lithium grease was examined by high resolution transmission electron microscope (HRTEM) and scanning electron microscope (SEM). The results indicated that the microscopic structure of the lithium grease presents a more regular and homogeneous network structure, with long fibers, which confirms the rheological stability.

Enhancement of biogas production from sewage sludge by addition of grease trap sludge

International Nuclear Information System (INIS)

Grosser, A.; Neczaj, E.

2016-01-01

Highlights: • Addition of grease trap sludge is interesting option for sewage sludge digestion. • Co-digestion of grease trap sludge and sewage sludge improved efficiency of process. • The anaerobic digestion can be carried out at short hydraulic retention time. • Long chain fatty acids concentration was below the ranges for inhibition of anaerobic digestion. - Abstract: Despite having many benefits, a low degree of volatile solids removal as well as long retention time are the main factors limiting the performance of the anaerobic digestion. Co-digestion of sewage sludge with other organic waste (for example fat rich materials) is one of the few potential ways to enhance the performance of the anaerobic digestion. In this article, the effects of adding fatty rich materials on the performance and stability of semi-continuous anaerobic digestion of sewage sludge were investigated on a 6 l laboratory-scale reactor (working volume equal to 5.5 l). The reactor was operated in a semi-continuous mode with a hydraulic retention time of 10 days. The data presented in this paper relate to the period in which the grease trap sludge accounted for 10, 12, 14, 16 and 18% of the mixture on the volatile solids basis. The results clearly indicate that the addition of fat rich materials like grease trap sludge can lead to a satisfactory increase in biogas yield in digester treating sewage sludge. The results showed that co-digestion can enhance the biogas yield by 28–82% compared to anaerobic digestion of sewage sludge alone (control sample). Moreover, the addition of grease trap sludge to digesters resulted in increased volatile solids removal from 44.38% (control sample) to 57.77% (feedstock with 14% addition of grease trap sludge). It was found that the increase of grease trap sludge in the feedstock had a direct impact on the biogas production and methane yield. This proposal has also been confirmed by statistical analysis such as Pearson correlation coefficients and

Evaluation of oil and grease removal by adsorptive polymeric resins in semi-industrial scale: influence of temperature; Avaliacao da remocao de oleos e graxas por resinas polimericas adsorventes em escala semi-industrial: influencia da temperatura

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Luis F.S. de; Silva, Carla M.F. da; Queiros, Yure G.C.; Lucas, Elizabete F. [Universidade Federal do Rio de Janeiro, Instituto de Macromoleculas, Laboratorio de Macromoleculas e Coloides na Industria de Petroleo, Rio de Janeiro, RJ (Brazil)], e-mail: elucas@ima.ufrj.br

2011-07-01

The aim of this study was to evaluate the performance of polymeric resins packed in a fixed bed eluted in semi-industrial scale for oil and greases removal disposed in synthetic oily water in different temperature conditions. For this work, columns packed with vinyl and acryl polymer-base were tested and their efficiency of oil removal was evaluated by fluorimetry technique in two different temperatures: 25 and 60 deg C, in a flow rate condition of 200 mL/min. The experimental results were very good: the removal efficiencies were above 98% in both cases. At 60 deg C, the system keep the efficiency for a longer time: no significant loss in the efficiency was observed after eluting 1,000 times of the column bed volume at 25 deg C and 2,000, at 60 deg C. This result characterizes a great potential of application in the industry. (author)

ubaegesi@yahoo.co.uk Effects of oil spillage on Soil and Surface

African Journals Online (AJOL)

MICHAEL HORSFALL

Keywords: Tozicity, heavy metals, soil and water, WHO standard, Odoro Ikot Ukanafun, ... temperature, pH, electrical conductivity, oil/grease, copper (Cu), cadmium ... recommended standards, therefore there is need for remediation or clean up ... the soil sample analytical results show that the crude oil has polluted the soil ...

Application of a Thermodynamic Concept for the Analysis of Structural Degradation of Soap Thickened Lubricating Greases

Directory of Open Access Journals (Sweden)

Erik Kuhn

2018-01-01

Full Text Available Lubricating greases are special lubricants with a wide range of application. The tribologically stressed grease is used as tribological system and finally modeled as an open thermodynamic system. This study investigated the phenomenon of self-optimization and applied to the process of shearing a grease. The conditions for self-optimization and the consequences of created dissipative structures are investigated according to the interpreted literature.

Enzyme pretreatment of fats, oil and grease from restaurant waste to prolong septic soil treatment system effectiveness.

Science.gov (United States)

Dong, Younsuk; Safferman, Steven I; Ostahowski, Jeff; Herold, Tom; Panter, Ronald

2017-01-02

When a fast-food restaurant's wastewater containing fats, oil and grease (FOG) is discharged into a collection system, it builds up over time and clogs pipes. Similarly, when such wastewater flows into a septic soil treatment system, it adheres to the surface of inlet pipes, gravel/distribution media and soil, restricting the flow and eventually clogging the septic soil treatment system. In this study, an enzymatic pretreatment system was tested on wastewater from a fast-food restaurant to determine its effectiveness in preventing septic soil treatment system clogging. This system used aeration equipment, baffles and a one-time inoculum that excretes enzymes to reduce the molecular weight and number of double bonds associated with FOG. FOG containing triglycerides having lower molecular weights and fewer double bonds are less sticky. The enzymatic pretreatment system was found to cause these changes as verified by measuring the types of triglycerides (compounds in FOG) using liquid chromatography/mass spectrometry. A unique bench-scale septic soil treatment system (soil trench) was also used. Each contained six soil moisture sensors to enable the determination of moisture saturation trends among the five tested conditions: sanitary wastewater only, a combination of sanitary and kitchen wastewater, enzymatically pretreated sanitary and kitchen wastewater, kitchen wastewater, and enzymatically pretreated kitchen wastewater. For all influent types, a significant amount of FOG and other pollutants were removed, regardless of the initial concentrations. Moisture sensor readings showed differences among the tested conditions, indicating that septic soil treatment system clogging was delayed. Inspection of the influent pipe and gravel at the end of testing verified these differences as did the measurements of volatile solids.

Preliminary Study on Treatment of Palm Oil Mill Effluent (POME by Sand Filtration-DBD Plasma System

Directory of Open Access Journals (Sweden)

Ariadi Hazmi

2016-02-01

Full Text Available In the palm oil industry, open ponding, aerobic and anaerobic digestion, physicochemical treatment and membrane filtration are generally applied as conventional treatments of palm oil mill effluent (POME. In this study, a sand filtration-dielectric barrier discharge (DBD system was investigated as an alternative process for treating POME. This system can reduce land usage, processing time and costs compared to conventional systems. The removal efficiency of chemical oxygen demand (COD, biological oxygen demand (BOD5, and oil-grease in relation to the applied voltage were studied. Furthermore, the pH and temperature profiles were investigated. The obtained results indicate that the removal efficiency of COD, BOD5, and oil-grease increased with an increase of the applied voltage. The electrical energy consumption needed is about 10.56 kWh/L of POME.

A study of the use of bio-based technologies (lubricant and grease) in rail applications.

Science.gov (United States)

2014-05-01

The objective of the project was to study the efficacy of using bio-based lubricant and grease technologies in railroad applications : (locomotives and maintenance of way equipment). Several commercially available rail curve greases were identified a...

Nanoclays for polymer nanocomposites, paints, inks, greases

Indian Academy of Sciences (India)

... rheological modifier for paints, inks and greases, drug delivery vehicle for controlled release of therapeutic agents, and nanoclays for industrial waste water as well as potable water treatment to make further step into green environment. A little amount of nanoclay can alter the entire properties of polymers, paints, inks and ...

Greasing the Wheels of Trade

OpenAIRE

Hendrik P. van Dalen; Aico P. van Vuuren

2003-01-01

This discussion paper resulted in a publication in 'De Economist' , 2005, 153(2), 139-165. How much does a nation spend on resources to 'grease the wheels of trade'? To examine this question the Dutch economy is used as an exemplary case as the Netherlands are known as a nation of traders. This image was derived in the seventeenth century from successes in long distance trade, shipping and financial innovations. Despite its historical background in trading the potential to 'truck and barter' ...

Isocyanate-functionalized chitin and chitosan as gelling agents of castor oil.

Science.gov (United States)

Gallego, Rocío; Arteaga, Jesús F; Valencia, Concepción; Franco, José M

2013-06-03

The main objective of this work was the incorporation of reactive isocyanate groups into chitin and chitosan in order to effectively use the products as reactive thickening agents in castor oil. The resulting gel-like dispersions could be potentially used as biodegradable lubricating greases. Three different NCO-functionalized polymers were obtained: two of them by promoting the reaction of chitosan with 1,6-hexamethylene diisocyanate (HMDI), and the other by using chitin instead of chitosan. These polymers were characterized through 1H-NMR, FTIR and thermogravimetric analysis (TGA). Thermal and rheological behaviours of the oleogels prepared by dispersing these polymers in castor oil were studied by means of TGA and small-amplitude oscillatory shear (SAOS) measurements. The evolution and values of the linear viscoelasticity functions with frequency for -NCO-functionalized chitosan- and chitin-based oleogels are quite similar to those found for standard lubricating greases. In relation to long-term stability of these oleogels, no phase separation was observed and the values of viscoelastic functions increase significantly during the first seven days of ageing, and then remain almost constant. TGA analysis showed that the degradation temperature of the resulting oleogels is higher than that found for traditional lubricating greases.

An Electrochemical Processing Strategy for Improving Tribological Performance of Aisi 316 Stainless Steel Under Grease Lubrication

Science.gov (United States)

Zou, Jiaojuan; Li, Maolin; Lin, Naiming; Zhang, Xiangyu; Qin, Lin; Tang, Bin

2014-12-01

In order to improve the tribological performance of AISI 316 stainless steel (316 SS) under grease lubrication, electrochemical processing was conducted on it to obtain a rough (surface texturing-like) surface by making use of the high sensitivity of austenitic stainless steel to pitting corrosion in Cl--rich environment. Numerous corrosion pits or micro-ditches acted as micro-reservoirs on the obtained surface. While the grease could offer consistent lubrication, and then improve the tribological performance of 316 SS. Tribological behaviors of raw 316 SS and the treated sample were measured using a reciprocating type tribometer sliding against GCr15 steel counterpart under dry and grease lubrication conditions. The results showed that the mass losses of the two samples were in the same order of magnitude, and the raw sample exhibited lower friction coefficient in dry sliding. When the tests were conducted under grease lubrication condition, the friction coefficients and mass losses of the treated sample were far lower than those of the raw 316 SS. The tribological performance of 316 SS under grease lubrication was drastically improved after electrochemical processing.

The National Shipbuilding Research Program. Following Development of the Federal Effluent Guidelines for Metal Products and Machinery Facilities

Science.gov (United States)

1999-02-01

Cleaning Rules to Shipyards SDO\\SECT1 1-1 1. Introduction Background The Federal Clean Water Act (CWA) established a program to restore and maintain the...2-1 2. MP&M Rulemaking Process EPA Categorical Discharge Standards Program The Clean Water Act established a program to restore and... microfiltration and reverse osmosis. • Oil and grease content is used as a surrogate for monitoring toxic organics. • The technical and financial

Bioremediation of petrochemical sludge from oil refining operations

International Nuclear Information System (INIS)

Prince, M.J.; Sambasivam, Yasodha

1991-01-01

Petroleum refineries have historically produced large quantities of hydrocarbon sludge as a waste product. A common past practice for disposal of this material was to deposit it in open pits. These hazardous waste sites now require remediation to meet current environmental regulations. This report will present data from a feasibility study on bioremediation for one such site. Data will be presented on the characteristics and composition of the crude sludge including organic analysis by GC/MS techniques, loss on ignition, TOC pH, oil and grease levels, metals content by atomic adsorption and bacteria plate counts. The effectiveness of bioremediation will be examined using data from shaker flask studies with indigenous and other bacteria sources. Key parameters being monitored will include toxicity using a Microtox assay, oil and grease levels, and the concentration of individual chemical species using GC/MS analysis. Biological data such as bacteria growth rates and nutrient uptake rates will also be presented and compared to biodegradation rates

Performance of a Small-scale Treatment Wetland for Treatment of Landscaping Wash Water

Science.gov (United States)

Thompson, R. J.; Fayed, E.; Fish, W.

2011-12-01

A large number of lawn mowers and related equipment must be cleaned each day by commercial landscaping operations and state and local highway maintenance crews. Washing these devices produces wastewater that contains high amounts of organic matter and potentially problematic nutrients, as well as oil and grease and other chemicals and metals that come from the machinery itself. Dirty water washes off the mowers, flows off the pavement and into nearby storm drains without any kind of treatment. A better idea would be to collect such wastewater, retain it in an appropriate catchment such as an engineered wetland where natural processes could break down any pollutants in the wash water, and allow the water to naturally evaporate or percolate into the soil where it could recharge ground water resources safely. This research examines the performance of a small-scale treatment wetland tailored to remove nitrogen from landscaping wash water by incorporating both aerobic and anaerobic phases. Contaminants are analyzed through physical and chemical methods. Both methods involve collection of samples, followed by standardized, validated analytical laboratory tests for measuring total solids, total kjeldahl nitrogen, nitrates, total and dissolved phosphorus, COD, BOD, oil and grease, and metals (Zn and Cu). High levels of total solids, total kjeldahl nitrogen, nitrates, total and dissolved phosphorus, COD, BOD, oil and grease are found. Zinc and copper levels are low. Wetland treatment removes 99% total solids, 77% total kjeldahl nitrogen, 100% nitrates, 94% total phosphorus, 86% dissolved phosphorus, 94% COD, 97% BOD, and 76% oil and grease. The results will be a critical step towards developing a sustainable low-energy system for treating such wastewater that could be used by private landscaping companies and government agencies.

Evaluation of castor oil samples for potential toxin contamination

Science.gov (United States)

Castor oil and its derivatives are widely used as a chemical feedstock for production of lubricants and greases, and for engineering plastics, plasticizers and surfactants. They also have wide application in consumer goods such as lipstick, deodorants and medicinal products. Due to concerns about th...

Rheological Properties of Extreme Pressure Greases Measured Using a Process Control Rheometer

DEFF Research Database (Denmark)

Glasscock, Julie; Smith, Robin S.

2012-01-01

A new process control rheometer (PCR) designed for use in industrial process flows has been used to measure the rheological properties of three extreme-pressure greases. The rheometer is a robust yet sensitive instrument designed to operate in an industrial processing environment in either in......-line or on-line configurations. The PCR was able to measure the rheological properties including the elastic modulus, viscous modulus, and complex viscosity of the greases which in an industrial flow application could be used as variables in a feedback system to control the process and the quality...

Benzoxazole and Benzothiazole Antirust Greases. Work Unit Directive (WUD) 51

National Research Council Canada - National Science Library

Christian, John

1980-01-01

...) and polytetrafluoroethylene (PTFE) thickeners. Testing has shown that one percent concentrations of the additives in the grease formulations provide inhibition against rusting of ferrous metal components under conditions of high humidity...

46 CFR 62.50-30 - Additional requirements for periodically unattended machinery plants.

Science.gov (United States)

2010-10-01

... include machinery plants and spaces that are automated to the degree that they are self-regulating and... engineers' accommodations. Other than fire or flooding alarms, this may be accomplished by summarized visual... in § 111.103 of this chapter; and (7) Voice communications with the bridge. (i) Oil leakage. Leakages...

Effects of ultrasonic and thermo-chemical pre-treatments on methane production from fat, oil and grease (FOG) and synthetic kitchen waste (KW) in anaerobic co-digestion.

Science.gov (United States)

Li, Chenxi; Champagne, Pascale; Anderson, Bruce C

2013-02-01

The effects of ultrasonic and thermo-chemical pre-treatments on the methane production potential of anaerobic co-digestion with synthetic kitchen waste (KW) or fat, oil and grease (FOG) were investigated. Non-linear regressions were fitted to accurately assess and compare the methane production from co-digestion under the various pre-treatment conditions and to achieve representative simulations and predictions. Ultrasonic pre-treatment was not found to improve methane production effectively from either FOG co-digestion or KW co-digestions. Thermo-chemical pre-treatment could increase methane production yields from both FOG and KW co-digestions. COD solubilization was found to effectively represent the effects of pre-treatment. A comprehensive evaluation indicated that the thermo-chemical pre-treatments of pH=10, 55°C and pH=8, 55°C provided the best conditions to increase methane production from FOG and KW co-digestions, respectively. The most effective enhancement of biogas production (288±0.85mLCH(4)/g TVS) was achieved from thermo-chemically pre-treated FOG co-digestion, which was 9.9±1.5% higher than FOG co-digestion without thermo-chemical pre-treatment. Copyright © 2012 Elsevier Ltd. All rights reserved.

Preliminary research on measuring grease in petroleum pipeline using fast neutron transmission method

International Nuclear Information System (INIS)

Liu Qingwei; Liu Shengkang; Zhang Zhiping; Ding Xiaoping

2006-01-01

The principle, experiment and conclusion on the grease stain measurement using fast neutron are reported. The experiment equipment consist of 241 Am-Be fast neutron source, ZnS detector and BH1224 multichannel spectrometer. Paraffin is used instead of real grease stain. Steel plates are used instead of pipeline. The results of the experiment indicate that there is a good linearship between the logarithm of the reciprocal of the neutron transmissivity and the paraffin thickness. The measuring accuracy of the paraffin thickness is 0.6 mm in this experiment. (authors)

Software para estimativa do custo operacional de máquinas agrícolas - MAQCONTROL Development of software to compute operational costs of farm machinery - MAQCONTROL

Directory of Open Access Journals (Sweden)

Liane Piacentini

2012-06-01

Full Text Available A seleção e a otimização de sistemas mecanizados são os principais objetivos da mecanização racional. Não é suficiente uma compra adequada do maquinário agrícola se sua utilização não for controlada em aspectos operacionais e financeiros. Neste trabalho, é descrito o desenvolvimento de software para estimativa do custo operacional de máquinas agrícolas (MAQCONTROL, utilizando o ambiente de desenvolvimento Borland Delphi e o banco de dados Firebird. Os custos operacionais foram divididos em fixos e variáveis. Nos custos fixos, foram estimadas as despesas com depreciação, juros, alojamento e seguros. Nos custos variáveis, foi dada ênfase aos custos de manutenção como: óleos lubrificantes, filtros, pneus, graxa, combustível, pequenos reparos e troca de peças. Os resultados demonstraram a eficiência do software para os objetivos propostos. Assim, o MAQCONTROL pode ser uma importante ferramenta no processo de administração rural, pois reduz os custos da informação e agiliza a determinação precisa dos custos operacionais de máquinas agrícolas.The rational mechanization has as main objectives the selection and optimization of mechanized systems. An adequate purchase of agricultural machinery is not sufficient if its use is not controlled in operational and financial aspects. This work describes the development of software to estimate operational costs of agricultural machinery (MAQCONTROL, using Borland Delphi's development environment and Firebird database. The operational costs were divided in fixed and variable. In fixed costs, the expenses with depreciation, interest, storage and insurance were estimated. In variable costs, the emphasis was given to the expenses on maintenance, lubricating oils, filters, tires, grease, fuel, small repairs, and parts replacement. Results have shown the software efficiency for the proposed objectives. Therefore, the MAQCONTROL software proved to be an important tool in the rural

33 CFR 151.25 - Oil Record Book.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Oil Record Book. 151.25 Section... Treaty as it Pertains to Pollution from Ships Oil Pollution § 151.25 Oil Record Book. (a) Each oil tanker... fixed or floating drilling rig or other platform shall maintain an Oil Record Book Part I (Machinery...

Design of the GLARE tool. A grease lubrication apparatus for research and education

International Nuclear Information System (INIS)

Rawlings, B.

2012-01-01

The GLARE: Grease Lubrication Apparatus for Research and Education was designed as a fourth year thesis project with the University of Ontario Institute of Technology (UOIT). The purpose of the apparatus is to train Ontario Power Generation Nuclear (OPGN) staff to properly lubricate bearings with grease and to help detect early equipment failures. Proper re-lubrication is critical to the nuclear industry as equipment may be inaccessible for long periods of time. A secondary purpose for the tool is for UOIT research and undergraduate laboratories.This abstract provides an overview of the project and its application to the nuclear industry. (author)

Effects of a polymeric organic coagulant for industrial mineral oil ...

African Journals Online (AJOL)

The removal of chemical oxidation demand (COD), soap oil and grease (SOG), total suspended solids (TSS) and turbidity from the MOW were used as the response variables for the coagulation flotation process. This was done with a standard dissolved air flotation jar test. The results show that the actual COD, SOG, TSS ...

Application of Fenton process to remove organic matter and PCBs from waste (fuller's earth) contaminated with insulating oil.

Science.gov (United States)

da Silva, Milady Renata Apolinário; Rodrigues, Eduardo de Oliveira; Espanhol-Soares, Melina; Silva, Flavio Soares; Kondo, Márcia Matiko; Gimenes, Rossano

2018-01-09

Polychlorinated biphenyls (PCBs) are carcinogenic to humans and can be found in fuller's earth used for the treatment of used transformer oil. This work describes an optimization of the Fenton process for the removal of contaminants from fuller's earth. The effects of pH (2.5 and 4.0), [H 2 O 2 ] (1.47 and 2.07 mol L -1 ), and [Fe 2+ ] (1.7 and 40 mmol L -1 ) were studied. The Fenton process efficiency was monitored using the decreases in the chemical oxygen demand (COD) and the concentrations of oil and grease, total carbon (TC), PCBs, and H 2 O 2 . The fuller's earth contaminated with insulating oil presented 35% (w/w) of TC, 34% (w/w) of oil and grease, 297.0 g L -1 COD, and 64 mg of PCBs per kg. The material could therefore be considered a dangerous waste. After Fenton treatment, using a slurry mode, there was a removal of 55% of COD, 20% of oil and grease, and 20% of TC, achieved at pH 2.5 using 2.07 mol L -1 of H 2 O 2 and 40.0 mmol L -1 of Fe 2+ . No PCBs were detected in the samples after the Fenton treatment, even using smaller amounts of Fenton reagents (1.47 mol L -1 of H 2 O 2 , 1.7 mmol L -1 of Fe 2+ , pH 2.5). The results indicated that the treated fuller's earth was free from PCB residues and could be disposed of in a simple landfill, in accordance with Brazilian PCB regulations.

Treatment of Oily Wastewater Produced From Old Processing Plant of North Oil Company

Directory of Open Access Journals (Sweden)

Dr. Faris Hammoodi Al-Ani

2012-03-01

Full Text Available The main objectives of this research were to study and analyses oily wastewater characteristics originating from old-processing plant of North Oil Company and to find a suitable and simple method to treat the waste so it can be disposed off safely. The work consists of two stages; the first was the study of oily wastewater characteristics and its negative impacts. The results indicated that oil and grease were the most dominant pollutant with concentration range between 1069 – 3269.3 mg/l that must be removed; other pollutants were found to be within Iraqi and EPA standards. The next stage was the use of these characteristics to choose the proper technology to treat that wastewater. This stage was divided into two stages: the first stage was a jar tests to find the optimum doses of alum, lime and powdered activated carbon (PAC. The second stage was the treatment by a batch pilot plant constructed for this purpose employing the optimum doses as determined from the first stage to treat the waste using a flotation unit followed by a filtration-adsorption unit. The removal efficiencies of flotation unit for oil and grease, COD, and T.S.S found to be 0.9789, 0.974, and 0.9933, respectively, while the removal efficiency for T.D.S was very low 0.0293. From filtration – adsorption column the removal efficiencies of oil and grease, T.D.S, COD, and T.S.S were found to be 0.9486, 0.8908, 0.6870, and 0.7815, respectively. The overall removal efficiencies of pilot plant were 0.9986, 0.8939, 0.9921, and 0.9950, respectively. The results indicated that this type of treatment was the simplest and most effective method that can be used to treat produced oily wastewater before disposal

Life cycle management. Condition monitoring of wind power plants; Life-cycle-management. Zustandsueberwachung von Windenergieanlagen

Energy Technology Data Exchange (ETDEWEB)

Wolff, R. [cmc GmbH, Kiel (Germany)

2013-06-01

The author of the contribution under consideration reports on maintenance strategies and condition monitoring in the field of wind energy. Beside the components in the drive train of wind turbines under consideration, the condition monitoring of the hardware systems and their software is explained. A brief overview of the field of machinery diagnosis and an explanation of the transmission of the measured data follow. Additional sensors such as sensors for the rotor blade monitoring, oil particles counter or oil quality sensors are described. In the field of diagnostic certainty, special follow-up studies such as video endoscopy, analysis of oil or grease, filter testing and material testing are discussed. The information from these thematic fields is used in the life-cycle management database for operationally relevant evaluations and considerations of economy of condition monitoring systems.

Effect of bacterial lipase on anaerobic co-digestion of slaughterhouse wastewater and grease in batch condition and continuous fixed-bed reactor.

Science.gov (United States)

Affes, Maha; Aloui, Fathi; Hadrich, Fatma; Loukil, Slim; Sayadi, Sami

2017-10-10

This study aimed to investigate the effects of bacterial lipase on biogas production of anaerobic co-digestion of slaughterhouse wastewater (SHWW) and hydrolyzed grease (HG). A neutrophilic Staphylococcus xylosus strain exhibiting lipolytic activity was used to perform microbial hydrolysis pretreatment of poultry slaughterhouse lipid rich waste. Optimum proportion of hydrolyzed grease was evaluated by determining biochemical methane potential. A high biogas production was observed in batch containing a mixture of slaughterhouse composed of 75% SHWW and 25% hydrolyzed grease leading to a biogas yield of 0.6 L/g COD introduced. Fixed bed reactor (FBR) results confirmed that the proportion of 25% of hydrolyzed grease gives the optimum condition for the digester performance. Biogas production was significantly high until an organic loading rate (OLR) of 2 g COD/L. d. This study indicates that the use of biological pre-treatment and FBR for the co-digestion of SHWW and hydrolyzed grease is feasible and effective.

Recycling of Automotive Lubricating Waste Oil and Its Quality Assessment for Environment-Friendly Use

OpenAIRE

Naveed Anwar; Syed Shahid Ali; Zubair Anwar; Jabar Zaman Khan Khattak; Abdul Jabbar; Tariq M. Ansari; Syed Sibtain Raza Naqvi

2012-01-01

Lubricating oils, which are formulated with a number of chemicals blended base oils provide products that last longer, keep machinery cleaner and allow the machinery to work better under severe operating conditions. However, the used oil-waste generated by the automobiles and other allied industries poses an environmental hazard. The motivation of the present research study was to study the merits and demerits of commonly applicable technique acid/clay for reclamation of waste oil. This proce...

40 CFR 761.375 - Specific requirements for surfaces coated or covered with dust, dirt, grime, grease, or another...

Science.gov (United States)

2010-07-01

... coated or covered with dust, dirt, grime, grease, or another absorbent material. 761.375 Section 761.375... coated or covered with dust, dirt, grime, grease, or another absorbent material. (a) First wash. Cover..., absorbent pad until the surface appears dry. This cleaning should remove any residual dirt, dust, grime, or...

Improving machinery reliability

CERN Document Server

Bloch, Heinz P

1998-01-01

This totally revised, updated and expanded edition provides proven techniques and procedures that extend machinery life, reduce maintenance costs, and achieve optimum machinery reliability. This essential text clearly describes the reliability improvement and failure avoidance steps practiced by best-of-class process plants in the U.S. and Europe.

Wear of Spur Gears Having a Dithering Motion and Lubricated with a Perfluorinated Polyether Grease

Science.gov (United States)

Krantz, Timothy; Oswald, Fred; Handschuh, Robert

2007-01-01

Gear contact surface wear is one of the important failure modes for gear systems. Dedicated experiments are required to enable precise evaluations of gear wear for a particular application. The application of interest for this study required evaluation of wear of gears lubricated with a grade 2 perfluorinated polyether grease and having a dithering (rotation reversal) motion. Experiments were conducted using spur gears made from AISI 9310 steel. Wear was measured using a profilometer at test intervals encompassing 10,000 to 80,000 cycles of dithering motion. The test load level was 1.1 GPa maximum Hertz contact stress at the pitch-line. The trend of total wear as a function of test cycles was linear, and the wear depth rate was approximately 1.2 nm maximum wear depth per gear dithering cycle. The observed wear rate was about 600 times greater than the wear rate for the same gears operated at high speed and lubricated with oil.

Radioisotope studies on the paradox in dispersion and agglomeration of sewage greases discharged from ocean outfalls

International Nuclear Information System (INIS)

Davison, A.; Easy, J.F.; Seatonberry, B.W.

1981-04-01

Experiments have been undertaken in the ocean off Sydney, Australia to monitor the movement and the dispersion of sewage solids. These solids were labelled with a radioisotope, gold-198 prior to ocean discharge. The labelled material was followed at sea using submersible scintillation detectors. Lateral and vertical dispersion coefficients were determined. The experiments showed that under some conditions the labelled sewage grease dispersed and under others the grease agglomerated. This variation is explained in terms of non-conservative processes

On the normal stress effect in grease-lubricated bearing seals

NARCIS (Netherlands)

Baart, P.; Lugt, Pieter Martin; Prakash, B.

2014-01-01

The film formation in lip seals, due to the non-Newtonian rheology of the lubricant, has been a topic of speculation. Earlier work suggests that normal stresses in grease would be favorable for the film buildup between the seal lip and shaft or bearing ring. In the current article, we evaluate this

Pumping machinery theory and practice

CERN Document Server

Badr, Hassan M

2014-01-01

Pumping Machinery Theory and Practice comprehensively covers the theoretical foundation and applications of pumping machinery. Key features: Covers characteristics of centrifugal pumps, axial flow pumps and displacement pumpsConsiders pumping machinery performance and operational-type problemsCovers advanced topics in pumping machinery including multiphase flow principles, and two and three-phase flow pumping systemsCovers different methods of flow rate control and relevance to machine efficiency and energy consumptionCovers different methods of flow rate control and relevance to machine effi

Removal of oil from water by bentonite

International Nuclear Information System (INIS)

Moazed, H.; Viraraghavan, T.

1999-01-01

Many materials, included activated carbon, peat, coal, fiberglass, polypropylene, organoclay and bentonite have been used for removing oils and grease from water. However, bentonite has been used only rarely for this purpose. In this study Na-bentonite was used to remove oil from oil-in-water emulsions of various kinds such as standard mineral oil, cutting oils, refinery effluent and produced water from production wells at Estevan, Saskatchewan. Removal efficiencies obtained were 85 to 96 per cent for cutting oils, 84 to 86 per cent for produced water and 54 to 87 per cent for refinery effluent. Bentonite proved to be more effective in the removal of oil from oil-in-water emulsions than from actual waste waters; up to 96 percent from oil-in-water emulsions to only 87 per cent from actual waste water. The percentage of oil removed was found to be a function of the amount of bentonite added and the adsorption time up to the equilibrium time. Result also showed that the Langmuir, Freundlich and BET isotherms are well suited to describe the adsorption of oil by bentonite from the various oily waters employed in this study. 15 refs

77 FR 462 - Regulation of Fuels and Fuel Additives: Identification of Additional Qualifying Renewable Fuel...

Science.gov (United States)

2012-01-05

... sources--qualifying as cellulosic biofuel: [cir] Thermochemical pyrolysis. [cir] Thermochemical... covercrops, algal oil, biogenic waste oils/fats/greases, non-food grade corn oil, Canola/rapeseed oil, and... from annual covercrops, algal oil, biogenic waste oils/fats/greases, or non- food grade corn oil using...

Oil and natural gas technology review-lubrication and lubricants

Energy Technology Data Exchange (ETDEWEB)

Moos, J

1966-01-01

A summary is presented of the advances made during 1967 in the following areas: production and transmission of natural gas; geosciences; drilling and production technology; secondary recovery; transportation by tanker, pipelines, and tank cars; storage; planning of refineries; control and automation; cracking and gasification of crude oil; separation and hydrogenation processes; petrochemicals; combustion technology; fuels and additives; air and water pollution control; production of lubricants; lubrication with mist, gas, and vapors; hydraulic fluids; lubricant additives; oxidation and aging of oils; greases; solid lubricants; bearings; machining; friction and wear; and changes in materials of construction. (220 refs.)

Effects of the concentration of emulsion of oil-in-water on the propagation velocity and attenuation

International Nuclear Information System (INIS)

Silva, L S F; Bibiano, D S; Figueiredo, M K K; Costa-Félix, R P B

2015-01-01

Soybean oil is an important feedstock for production of biodiesel that generates about 20 % of oily effluents. This paper studied the effect of concentration of soybean oil-inwater emulsions, in the range from 6 000 to 14 000 ppm, on the propagation velocity and ultrasonic attenuation. The Emission-Reception method has shown that the propagation velocity depends linearly on the concentration. The behavior of attenuation is similar to the velocity. Thus, both parameters can be used to measure oils and greases content in water

Effects of Atomic Oxygen and Grease on Outgassing and Adhesion of Silicone Elastomers for Space Applications

Science.gov (United States)

de Groh, Henry C.; Puleo, Bernadette J.; Steinetz, Bruce M.

An investigation of silicone elastomers for seals used in docking and habitat systems for future space exploration vehicles is being conducted at NASA. For certain missions, NASA is considering androgynous docking systems where two vehicles each having a seal would be required to: dock for a period of time, seal effectively, and then separate with minimum push-off forces for undocking. Silicone materials are generally chosen for their wide operating temperatures and low leakage rates. However silicone materials are often sticky and usually exhibit considerable adhesion when mated against metals and silicone surfaces. This paper investigates the adhesion unit pressure for a space rated silicone material (S0383-70) for either seal-on-seal (SoS) or seal-on-aluminum (SoAl) operation modes in the following conditions: as-received, after ground-based atomic-oxygen (AO) pre-treatment, after application of a thin coating of a space-qualified grease (Braycote 601EF), and after a combination of AO pre-treatment and grease coating. In order of descending adhesion reduction, the AO treatment reduced seal adhesion the most, followed by the AO plus grease pre-treatment, followed by the grease treatment. The effects of various treatments on silicone (S0383-70 and ELA-SA-401) outgassing properties were also investigated. The leading adhesion AO pre-treatment reduction led to a slight decrease in outgassing for the S0383-70 material and virtually no change in ELA-SA-401 outgassing.

Effects of peroxidized corn oil on performance, AMEn, and abdominal fat pad weight in broiler chicks

Science.gov (United States)

There is a trend to use more alternative lipids in poultry diets, either through animal-vegetable blends, distillers corn oil, or yellow grease. This has resulted in the use of lipids in poultry diets with a higher concentration of unsaturated fatty acids which have a greater potential for peroxidat...

On a new method to determine the yield stress in lubricating grease

NARCIS (Netherlands)

Cyriac, F.; Lugt, Pieter Martin; Bosman, Rob

2015-01-01

An experimental study using both a controlled stress and a controlled strain rheometer has been undertaken to characterize lubricating grease in shear, creep, stress relaxation, and oscillatory flow, with a main focus on determining the yield stress. The yield stress was examined using a cone–plate

9 CFR 316.15 - Marking outside containers of inedible grease, etc.

Science.gov (United States)

2010-01-01

... grease, etc. 316.15 Section 316.15 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE... letters not less than 2 inches high, while on tank cars and tank trucks the letters shall be not less than 4 inches high. (b) Inspected rendered animal fat which is intended not to be used for human food may...

A robust sebum, oil, and particulate pollution model for assessing cleansing efficacy of human skin.

Science.gov (United States)

Peterson, G; Rapaka, S; Koski, N; Kearney, M; Ortblad, K; Tadlock, L

2017-06-01

With increasing concerns over the rise of atmospheric particulate pollution globally and its impact on systemic health and skin ageing, we have developed a pollution model to mimic particulate matter trapped in sebum and oils creating a robust (difficult to remove) surrogate for dirty, polluted skin. To evaluate the cleansing efficacy/protective effect of a sonic brush vs. manual cleansing against particulate pollution (trapped in grease/oil typical of human sebum). The pollution model (Sebollution; sebum pollution model; SPM) consists of atmospheric particulate matter/pollution combined with grease/oils typical of human sebum. Twenty subjects between the ages of 18-65 were enrolled in a single-centre, cleansing study comparisons between the sonic cleansing brush (normal speed) compared to manual cleansing. Equal amount of SPM was applied to the centre of each cheek (left and right). Method of cleansing (sonic vs. manual) was randomized to the side of the face (left or right) for each subject. Each side was cleansed for five-seconds using the sonic cleansing device with sensitive brush head or manually, using equal amounts of water and a gel cleanser. Photographs (VISIA-CR, Canfield Imaging, NJ, USA) were taken at baseline (before application of the SPM), after application of SPM (pre-cleansing), and following cleansing. Image analysis (ImageJ, NIH, Bethesda, MD, USA) was used to quantify colour intensity (amount of particulate pollutants on the skin) using a scale of 0 to 255 (0 = all black pixels; 255 = all white pixels). Differences between the baseline and post-cleansing values (pixels) are reported as the amount of SPM remaining following each method of cleansing. Using a robust cleansing protocol to assess removal of pollutants (SPM; atmospheric particulate matter trapped in grease/oil), the sonic brush removed significantly more SPM than manual cleansing (P pollution method easily allows assessment of efficacy through image analysis. © 2016 The Authors

Wastewater transformations and fertilizer value when co-digesting differing ratios of swine manure and used cooking grease in low-cost digesters

Energy Technology Data Exchange (ETDEWEB)

Lansing, Stephanie [Department of Environmental Science and Technology, University of Maryland, 1445 Animal Sci./Ag. Eng. Bldg., College Park, MD 20742-2315 (United States); Martin, Jay F. [Department of Food, Agricultural, and Biological Engineering, The Ohio State University, 590 Woody Hayes Drive, Columbus, OH 43210-1057 (United States); Botero, Raul Botero; Nogueira da Silva, Tatiana; Dias da Silva, Ederson [EARTH University, Apartado Postal 4442 - 1000, San Jose (Costa Rica)

2010-12-15

A nine-month co-digestion investigation was conducted in Costa Rica to optimize animal wastewater treatment, renewable energy production, and fertilizer creation using 12 Taiwanese-model, plug-flow digesters (250 L each) constructed of tubular polyethylene and PVC piping, operating without mechanical or heating components. The experiment tested three replications of four treatment groups: the control (T0), which contained only swine manure, and T2.5, T5, and T10, which contained 2.5%, 5%, and 10% used cooking grease (by volume) combined with swine manure. T2.5 had the greatest methane production (45 L d{sup -1}), a 124% increase from the control. No adverse effects were observed from co-digesting 2.5% grease in terms of organic matter removal, pathogen reduction, grease removal, and pH. Chemical oxygen demand (COD) was reduced 94.7% to 1.96 g L{sup -1}, fecal coliforms and Escherichia coli were reduced 99.2 and 97.1%, respectively, and grease removal was 99.9%. The average effluent pH (7.05) and alkalinity in T2.5 was within the optimal range for methanogens and increased significantly during the nine-month experiment, likely due to adaptation of the methanogenic organisms to the influent grease concentrations. Total nitrogen concentration decreased 34.0%, and NH{sub 4}-N increased 97.1% during digestion in T2.5, with no significant differences between T2.5 and T0. There was less phosphorus reduction with co-digestion, with 181 mg g{sup -1} of total phosphorus (TP) in T2.5 and only 90.6 mg g{sup -1} of TP in T0, resulting in lower N:P ratios in the grease treatment groups due to the greater concentration of phosphorus in the effluent. (author)

Matrix analysis of electrical machinery

CERN Document Server

Hancock, N N

2013-01-01

Matrix Analysis of Electrical Machinery, Second Edition is a 14-chapter edition that covers the systematic analysis of electrical machinery performance. This edition discusses the principles of various mathematical operations and their application to electrical machinery performance calculations. The introductory chapters deal with the matrix representation of algebraic equations and their application to static electrical networks. The following chapters describe the fundamentals of different transformers and rotating machines and present torque analysis in terms of the currents based on the p

Estimation of modes frictions and greasing in bearing axial hanging of locomotives

Directory of Open Access Journals (Sweden)

V.N. Аstаkhоv

2012-04-01

Full Text Available Dependence is considered between the size of relative diametral gap and descriptions of work of the motor-axial bearing on the different rates of movement of diesel engine: by the type of the mode of greasing, thickness lubricating layer, by the coefficient of friction and intensity of wear.

Biological, medicinal and toxicological significance of Eucalyptus leaf essential oil: a review.

Science.gov (United States)

Dhakad, Ashok K; Pandey, Vijay V; Beg, Sobia; Rawat, Janhvi M; Singh, Avtar

2018-02-01

The genus Eucalyptus L'Heritier comprises about 900 species, of which more than 300 species contain volatile essential oil in their leaves. About 20 species, within these, have a high content of 1,8-cineole (more than 70%), commercially used for the production of essential oils in the pharmaceutical and cosmetic industries. However, Eucalyptus is extensively planted for pulp, plywood and solid wood production, but its leaf aromatic oil has astounding widespread biological activities, including antimicrobial, antiseptic, antioxidant, chemotherapeutic, respiratory and gastrointestinal disorder treatment, wound healing, and insecticidal/insect repellent, herbicidal, acaricidal, nematicidal, and perfumes, soap making and grease remover. In the present review, we have made an attempt to congregate the biological ingredients of leaf essential oil, leaf oil as a natural medicine, and pharmacological and toxicological values of the leaf oil of different Eucalyptus species worldwide. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Fault diagnosis of rotating machinery using an improved HHT based on EEMD and sensitive IMFs

International Nuclear Information System (INIS)

Lei, Yaguo; Zuo, Ming J

2009-01-01

A Hilbert–Huang transform (HHT) is a time–frequency technique and has been widely applied to analyzing vibration signals in the field of fault diagnosis of rotating machinery. It analyzes the vibration signals using intrinsic mode functions (IMFs) extracted using empirical mode decomposition (EMD). However, EMD sometimes cannot reveal the signal characteristics accurately because of the problem of mode mixing. Ensemble empirical mode decomposition (EEMD) was developed recently to alleviate this problem. The IMFs generated by EEMD have different sensitivity to faults. Some IMFs are sensitive and closely related to the faults but others are irrelevant. To enhance the accuracy of the HHT in fault diagnosis of rotating machinery, an improved HHT based on EEMD and sensitive IMFs is proposed in this paper. Simulated signals demonstrate the effectiveness of the improved HHT in diagnosing the faults of rotating machinery. Finally, the improved HHT is applied to diagnosing an early rub-impact fault of a heavy oil catalytic cracking machine set, and the application results prove that the improved HHT is superior to the HHT based on all IMFs of EMD

Model for Determining the Consumption of Machinery, Tableware, Fuel, Oils and Lubricants with the Participation of Units from the Bulgarian Army in Humanitarian Operations

Directory of Open Access Journals (Sweden)

Nichev Nikolay

2017-06-01

Full Text Available Regulating documents of the Bulgarian Army considered norms for support classic combat operations and in fact Bulgarian Army has no planning methods to be used for planning of humanitarian operations. Solving this problem can be achieved through the use of planning factors. Planning factors are generally based on experience or data on the use of resources from previous operations. The participation of units of the Bulgarian Army in humanitarian operations have failed to bring to the accumulation of data needed to create a suitable planning factors. The purpose of the study is to develop a model by which to bring out planning factors in determining the the consumption of machinery, tableware, fuel, oils and lubricants with the participation of units from the Bulgarian Army in humanitarian operations.

The Optimum Selection and Drawing Output Program Development of Shell and Tube Type Oil Cooler

International Nuclear Information System (INIS)

Lee, Y. B.; Kim, T. S.; Ko, J. M

2007-01-01

Shell and Tube type Oil Cooler is widely used for hydraulic presses, die casting machines, generation equipments, machine tools and construction heavy machinery. Temperature of oil in the hydraulic system changes viscosity and thickness of oil film. They have a bad effect to performance and lubrication of hydraulic machinery, so it is important to know exactly the heat exchanging efficiency of oil cooler for controlling oil temperature. But most Korean manufacturers do not have test equipment for oil cooler, so they cannot carry out the efficiency test of oil cooler and it is impossible to verify its performance. This paper includes information of construction of necessary utilities for oil cooler test and design and manufacture of test equipment. One can select the optimum product by obtaining performance data through tests of various kinds of oil coolers. And also the paper developed a program which can be easily used for design of 2D and 3D drawings of oil cooler

Vertical pump turbine oil environmental evaluation

Energy Technology Data Exchange (ETDEWEB)

Culver, G.

1991-04-01

In Oregon low-temperature geothermal injection well construction, siting and receiving formations requires approval by the Water Resources Department (OWRD). In addition, the Oregon Department of Environmental Quality (ODEQ) has regulations concerning injection. Conversations with the OWRD and ODEQ representatives indicated they were very concerned about the potential for contamination of the geothermal (and cooler but hydraulically connected) aquifers by oils and grease. Their primary concern was over the practice of putting paraffin, motor oils and other hydrocarbons in downhole heat exchanger (DHE) wells to prevent corrosion. They also expressed considerable concern about the use of oil in production well pumps since the fluids pumped would be injected. Oregon (and Idaho) prohibit the use of oil-lubricated pumps for public water supplies except in certain situations where non-toxic food-grade lubricants are used. Since enclosed-lineshaft oil-lubricated pumps are the mainstay of direct-use pumping equipment, the potential for restricting their use became a concern to the Geo-Heat Center staff. An investigation into alternative pump lubrication schemes and development of rebuttals to potential restrictions was proposed and approved as a contract task. (SM)

The Design of High Reliability Magnetic Bearing Systems for Helium Cooled Reactor Machinery

International Nuclear Information System (INIS)

Swann, M.; Davies, N.; Jayawant, R.; Leung, R.; Shultz, R.; Gao, R.; Guo, Z.

2014-01-01

The requirements for magnetic bearing equipped machinery used in high temperature, helium cooled, graphite moderated reactor applications present a set of design considerations that are unlike most other applications of magnetic bearing technology in large industrial rotating equipment, for example as used in the oil and gas or other power generation applications. In particular, the bearings are typically immersed directly in the process gas in order to take advantage of the design simplicity that comes about from the elimination of ancillary lubrication and cooling systems for bearings and seals. Such duty means that the bearings will usually see high temperatures and pressures in service and will also typically be subject to graphite particulate and attendant radioactive contamination over time. In addition, unlike most industrial applications, seismic loading events become of paramount importance for the magnetic bearings system, both for actuators and controls. The auxiliary bearing design requirements, in particular, become especially demanding when one considers that the whole mechanical structure of the magnetic bearing system is located inside an inaccessible pressure vessel that should be rarely, if ever, disassembled over the service life of the power plant. Lastly, many machinery designs for gas cooled nuclear power plants utilize vertical orientation. This circumstance presents its own unique requirements for the machinery dynamics and bearing loads. Based on the authors’ experience with machine design and supply on several helium cooled reactor projects including Ft. St. Vrain (US), GT-MHR (Russia), PBMR (South Africa), GTHTR (Japan), and most recently HTR-PM (China), this paper addresses many of the design considerations for such machinery and how the application of magnetic bearings directly affects machinery reliability and availability, operability, and maintainability. Remote inspection and diagnostics are a key focus of this paper. (author)

Effect of bacterial lipase on anaerobic co-digestion of slaughterhouse wastewater and grease in batch condition and continuous fixed-bed reactor

OpenAIRE

Affes, Maha; Aloui, Fathi; Hadrich, Fatma; Loukil, Slim; Sayadi, Sami

2017-01-01

Background This study aimed to investigate the effects of bacterial lipase on biogas production of anaerobic co-digestion of slaughterhouse wastewater (SHWW) and hydrolyzed grease (HG). A neutrophilic Staphylococcus xylosus strain exhibiting lipolytic activity was used to perform microbial hydrolysis pretreatment of poultry slaughterhouse lipid rich waste. Results Optimum proportion of hydrolyzed grease was evaluated by determining biochemical methane potential. A high biogas production was o...

46 CFR 58.01-50 - Machinery space, noise.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Machinery space, noise. 58.01-50 Section 58.01-50... MACHINERY AND RELATED SYSTEMS General Requirements § 58.01-50 Machinery space, noise. (a) Each machinery space must be designed to minimize the exposure of personnel to noise in accordance with IMO A.468(XII...

Cavitation in Hydraulic Machinery

Energy Technology Data Exchange (ETDEWEB)

Kjeldsen, M.

1996-11-01

The main purpose of this doctoral thesis on cavitation in hydraulic machinery is to change focus towards the coupling of non-stationary flow phenomena and cavitation. It is argued that, in addition to turbulence, superimposed sound pressure fluctuations can have a major impact on cavitation and lead to particularly severe erosion. For the design of hydraulic devices this finding may indicate how to further limit the cavitation problems. Chapter 1 reviews cavitation in general in the context of hydraulic machinery, emphasizing the initial cavitation event and the role of the water quality. Chapter 2 discusses the existence of pressure fluctuations for situations common in such machinery. Chapter 3 on cavitation dynamics presents an algorithm for calculating the nucleation of a cavity cluster. Chapter 4 describes the equipment used in this work. 53 refs., 55 figs.,10 tabs.

Biodegradation of polyurethane derived from castor oil

Directory of Open Access Journals (Sweden)

José M. Cangemi

2008-09-01

Full Text Available The aim of this research was to study the biodegradation of a polymer derived from castor oil, which is a renewable, natural material that is a practical alternative for the replacement of traditional polyurethane foams. Due to its molecular structure, which contains polyester segments derived from vegetable oil, the polymeric surface is susceptible to microorganism attack. This study tested the biological degrading agent that was in contact with the microorganisms resulting from microbiological grease degrading agents, when foam was inoculated. Solid-media agar-plate tests were conducted for their potential to evaluate the biodegradation of polymeric particles by specific strains of microorganisms during 216 hours. The growth rate was defined. This technique provides a way of distinguishing the degradation abilities of microorganisms from the degradability of materials.

Biodegradation of Alaska North Slope crude oil enhanced by commercial bioremediation agents

International Nuclear Information System (INIS)

Aldrett, S.; Bonner, J.S.; Mills, M.A.; McDonald, T.J.; Autenrieth, R.L.

1996-01-01

The biodegradation of crude oil was studied. Tests were conducted in which natural unpolluted seawater was collected and then contaminated with Alaska North Slope crude oil. The oil was weathered by heating it to 521 degrees F to remove the light-end hydrocarbons. A total of 13 different bioremediation agents were tested, each one separately. Three samples per treatment were destructively analysed for petroleum chemistry. The thirteen treatments were analyzed for oil and grease. It was found that microbial degradation of petroleum hydrocarbons was enhanced by the addition of bioremediation agents, but it was not possible to identify the intermediate products responsible for the increase of resolved petroleum hydrocarbons through time. It was suggested that caution be used when interpreting results since the protocols used to test the products were prone to uncontrollable variations. 11 refs., 5 tabs., 6 figs

29 CFR 1910.215 - Abrasive wheel machinery.

Science.gov (United States)

2010-07-01

... be securely fastened to the spindle and the bearing surface shall run true. When more than one wheel... 29 Labor 5 2010-07-01 2010-07-01 false Abrasive wheel machinery. 1910.215 Section 1910.215 Labor... OCCUPATIONAL SAFETY AND HEALTH STANDARDS Machinery and Machine Guarding § 1910.215 Abrasive wheel machinery. (a...

Strategies for Improving Enterprise Standardization Management of Tropical Crop Machinery

Institute of Scientific and Technical Information of China (English)

无

2007-01-01

@@ There are two categories of tropical crop machinery. One comprises operation machinery that is used for planting, managing and harvesting tropical crops, while the other comprises process machinery for processing tropical crops. Tropical crop machinery is distinguished from other agricultural machinery by the special crops that such machinery cultivates and processes.

Sand or grease? Corruption-institutional trust nexus in post-Soviet countries

OpenAIRE

Nazim Habibov; Elvin Afandi; Alex Cheung

2017-01-01

This paper empirically tests several hypotheses about the nexus of corruption-institutional trust in Post-Soviet transitional countries of the former Soviet Union and Mongolia. We use two different indices of institutional trust to check the robustness of our analysis and estimate OLS and instrumental variable models with and without interaction terms. All things considered, our findings reject “greases the wheels” and “trust begets an honest political system” hypotheses. Instead, our finding...

Contribution to the study of the physical stability of the suspensions of zinc oxide, titanium dioxide and precipitated sulphur employing emulsified solid greases like vehicle

International Nuclear Information System (INIS)

Porras Navarro, Martha

2001-01-01

This research evaluated the physical stability of the suspensions of zinc oxide, precipitated sulphur and titanium dioxide. By using emulsified vehicles of three solid greases: stearilic alcohol, stearic acid and beeswax. That varies the concentration of solid grease (2%, 4%, 6 %) and the velocity of agitation for the emulsified vehicle's preparation (250, 500, 750 revolutions by minutes). That got 81 suspensions, 27 for every grease employed. The following effects there were evaluated like indicators of the physical stability of the suspensions: volume of sediment, apparent viscosity, facility of resuspension. There was effected an analysis of the varying of two controlled factors to establish the importance since the statistical viewpoint of the variants of the process over the volume of the sediment. This study indicates that the selection of solid grease is an parameter which influence is significant, what supports the got data through the research. By giving as a result that the stearilic alcohol is the most competent vehicle for the preparation of these suspensions. (Author) [es

Frictional properties of lubrication greases with the addition of nickel nanoparticles in pneumatic cylinder

Science.gov (United States)

Chang, Ho; Lan, Chou-Wei; Guo, Jia-Bin

2011-12-01

This paper studies the influence of addition of 100 nm diameter nickel nano-particles on the friction properties of synthetic grease (Li base, VG100) in pneumatic cylinder. The friction force test of pneumatic cylinder equipment measures the frictional force between seal and cylinder bore in pneumatic cylinders. The lubricants with addition of nickel nano-particles were used for lubricating the contact interface between seal and cylinder bore. The friction force test equipment employ a load cell force sensor to measure the friction force between seals and cylinder bores. Results obtained from experimental tests are compared to determine the friction force between seals and cylinder bore in pneumatic cylinders. The study leads to the conclusion that the addition of nickel nano-particles to synthetic grease results in a decrease in friction force between seals and cylinder bores in pneumatic cylinder. This tribological behavior is closely related to the deposition of nano-particles on the rubbing surfaces

Improved surfactants formulation for remediation of oil sludge recovery

International Nuclear Information System (INIS)

Syed Hakimi Sakuma Syed Ahmad; Shahidan Radiman

2000-01-01

Surfactant enhanced remediation based on mobilisation of the residual NAPLs (oil sludge) which is radioactive depends on the tendency of the surfactants to lower interfacial tension. Mobilisation has greater potential than solubilisation to increase the rate of remediation. Optimised surfactants formulation was determined with concentration of Aqua 2000 and D Bond of 1% wt respectively, sodium chloride concentration of 2 gmL -1 and addition of 3% wt butanol as cosolvent. The formulation was of benefit not only able to decrease further the interfacial tension of aqueous solution containing oil emulsion, but also to make possible to be more mobile and destruction of mixed liquid crystals that formed. Formation of liquid crystals can hinders significantly recovery efficiency of aqueous solution containing oil emulsion in field remediation work. In a 100 litres soil column experiment conducted containing oil emulsion in field sludge soil and using the surfactants formulation for flushing, miniemulsion formed sizes maintained at average size between 125 nm and 280 nm before and after remediation. Total oil and grease concentration removed from the soil were significant due to the decreased in oil emulsion sizes, increase mobility and solubility. (Author)

A new green process for biodiesel production from waste oils via catalytic distillation using a solid acid catalyst – Modeling, economic and environmental analysis

Directory of Open Access Journals (Sweden)

Aashish Gaurav

2016-04-01

Full Text Available The challenges in the chemical processing industry today are environmental concerns, energy and capital costs. Catalytic distillation (CD is a green reactor technology which combines a catalytic reaction and separation via distillation in the same distillation column. Utilization of CD in chemical process development could result in capital and energy savings, and the reduction of greenhouse gases. The efficacy of CD and the economic merits, in terms of energy and equipment savings, brought by CD for the production of biodiesel from waste oil such as yellow grease is quantified. Process flow sheets for industrial routes for an annual production of 10 million gallon ASTM purity biodiesel in a conventional process (reactor followed by distillation and CD configurations are modeled in Aspen Plus. Material and energy flows, as well as sized unit operation blocks, are used to conduct an economic assessment of each process. Total capital investment, total operating and utility costs are calculated for each process. The waste oil feedstock is yellow grease containing both triglyceride and free fatty acid. Both transesterification and esterification reactions are considered in the process simulations. Results show a significant advantage of CD compared to a conventional biodiesel processes due to the reduction of distillation columns, waste streams and greenhouse gas emissions. The significant savings in capital and energy costs together with the reduction of greenhouse gases demonstrate that process intensification via CD is a feasible and new green process for the biodiesel production from waste oils. Keywords: Yellow grease, Catalytic distillation, Aspen plus economic analyzer, Process intensification

Caracterización de una biograsa de aceite vegetal de Jatropha curcas L y jabón de litio//Characterization of biogrease based on Jatropha curcas L vegetable oil and Lithium Soap Thickener

Directory of Open Access Journals (Sweden)

Juliano Chitue de Assunção Nascimento

2013-05-01

Full Text Available Los aceites vegetales poseen un gran potencial como fluido base y como sustituto de los aceites minerales para la formulación de grasas lubricantes, estos aceites son biodegradables y renovables. En el trabajo se determinaron las propiedades  fisicoquímicas, antidesgaste y de extrema presión de una biograsa de aceite vegetal de Jatropha curcas L y jabón de litio empleando los métodos de pruebas estándar para las grasas lubricantes. La biograsa posee un color amarillo claro, una textura suave y homogénea,  un grado de penetración NLGI 1, una temperatura de goteo de 145 oC, magnitudes adecuadas del contenido de álcalis libre y corrosión al cobre; así como  propiedades antidesgaste y de extrema presión similares a otras grasas minerales y biograsas formuladas con diferentes aceites vegetales. Palabras claves: biograsa, aceite de Jatropha curcas L, jabón de litio, propiedades fisicoquímicas, propiedades antidesgaste, propiedades de extrema presión. Characterization of biogrease based on Jatropha curcas L vegetable oil and Lithium Soap Thickener. Abstract Vegetable oils have a great potential as a base fluid and a substitute for mineral oil in grease formulation, these oils are biodegradable and renewable. In this paper were determined the  physicochemical, antiwear and extreme pressure properties of a biogrease based on Jatropha curcas L vegetable oil and lithium soap thickener using the lubricanting greases standard test methods. The biogrease have a light yellow color, soft and homogeneous texture, a penetration grade NLGI 1, a drop point of 145 oC, appropriate magnitudes of free alkalis and copper corrosion; as well as antiwear and extreme pressure properties similar to the other mineral lubricating grease and formulated biogreases with differents vegetable oils. Key words: biogrease, Jatropha curcas L vegetable oil, lithium soap thickener, physicochemical properties, antiwear properties, extreme pressure properties.

On Development of Agricultural Machinery Operating Service in Chongqing

Institute of Scientific and Technical Information of China (English)

Chongjing; TAN; Shi; YANG

2015-01-01

Development of agricultural machinery operating service in Chongqing takes on rapid increase in number of service organizations,diversified service methods,improvement in service level,and constant service income. However,there are some problems,including unreasonable composition and small scale of service organization,imbalanced development of four service methods,low service level,and low operating income of agricultural machinery households. To accelerate development of agricultural machinery operating service in Chongqing,it is recommended to take following measures: adjusting subsidy for purchase and operation of agricultural machinery; improving fiscal and taxation and financial system; speeding up infrastructure construction,establishing agricultural machinery information network,and improving organizational form and methods of agricultural machinery operating service.

Influences of Restaurant Waste Fats and Oils (RWFO from Grease Trap as Binder on Rheological and Solvent Extraction Behavior in SS316L Metal Injection Molding

Directory of Open Access Journals (Sweden)

Mohd Halim Irwan Ibrahim

2016-02-01

Full Text Available This article deals with rheological and solvent extraction behavior of stainless steel 316L feedstocks using Restaurant Waste Fats and Oils (RWFO from grease traps as binder components along with Polypropylene (PP copolymer as a backbone binder. Optimal binder formulation and effect of solvent extraction variables on green compacts are being analyzed. Four binder formulations based on volumetric ratio/weight fraction between PP and RWFO being mixed with 60% volumetric powder loading of SS316L powder each as feedstock. The rheological analysis are based on viscosity, shear rate, temperature, activation energy, flow behavior index, and moldability index. The optimal feedstock formulation will be injected to form green compact to undergo the solvent extraction process. Solvent extraction variables are based on solvent temperature which are 40 °C, 50 °C, and 60 °C with different organic solvents of n-hexane and n-heptane. Analysis of the weight loss percentage and diffusion coefficient is done on the green compact during the solvent extraction process. Differential Scanning Calorimeter (DSC is used to confirm the extraction of the RWFO in green compacts. It is found that all binder fractions exhibit pseudoplastic behavior or shear thinning where the viscosity decreases with increasing shear rate. After considering the factors that affect the rheological characteristic of the binder formulation, feedstock with binder formulation of 20/20 volumetric ratio between PP and RWFO rise as the optimal binder. It is found that the n-hexane solvent requires less time for extracting the RWFO at the temperature of 60 °C as proved by its diffusion coefficient.

Mineral oil barrier sequential polymer treatment for recycled paper products in food packaging

Science.gov (United States)

Paul, Uttam C.; Fragouli, Despina; Bayer, Ilker S.; Mele, Elisa; Conchione, Chiara; Cingolani, Roberto; Moret, Sabrina; Athanassiou, Athanassia

2017-01-01

Recycled cellulosic paperboards may include mineral oils after the recycle process, which together with their poor water resistance limit their use as food packaging materials. In this work, we demonstrate that a proper functionalization of the recycled paper with two successive polymer treatments, imposes a mineral oil migration barrier and simultaneously renders it waterproof and grease resistant, making it an ideal material for food contact. The first poly (methyl methacrylate) treatment penetrates the paper network and creates a protective layer around every fiber, permitting thus the transformation of the paperboard to a hydrophobic material throughout its thickness, reducing at the same time the mineral oil migration. Subsequently, the second layer with a cyclic olefin copolymer fills the open pores of the surface, and reduces the mineral oil hydrocarbons migration at levels below those proposed by the BMEL. Online liquid chromatography-gas chromatography coupled with flame ionization detection quantitatively demonstrate that this dual functional treatment prevents the migration of both saturated (mineral oil saturated hydrocarbons) and aromatic hydrocarbon (mineral oil aromatic hydrocarbons) mineral oils from the recycled paperboard to a dry food simulant.

Machinery Vibration Monitoring Program at the Savannah River Site

International Nuclear Information System (INIS)

Potvin, M.M.

1990-01-01

The Reactor Maintenance's Machinery Vibration Monitoring Program (MVMP) plays an essential role in ensuring the safe operation of the three Production Reactors at the Westinghouse Savannah River Company (WRSC) Savannah River Site (SRS). This program has increased machinery availability and reduced maintenance cost by the early detection and determination of machinery problems. This paper presents the Reactor Maintenance's Machinery Vibration Monitoring Program, which has been documented based on Electric Power Research Institute's (EPRI) NP-5311, Utility Machinery Monitoring Guide, and some examples of the successes that it has enjoyed

46 CFR 252.33 - Hull and machinery insurance.

Science.gov (United States)

2010-10-01

... 46 Shipping 8 2010-10-01 2010-10-01 false Hull and machinery insurance. 252.33 Section 252.33... Subsidy Rates § 252.33 Hull and machinery insurance. (a) Subsidy items. The fair and reasonable net premium costs (including stamp taxes) of hull and machinery, increased value, excess general average...

Experimental preliminary exploration on determining grease thickness simulated by paraffin in petroleum pipelines

International Nuclear Information System (INIS)

Zhao Nongxiao; Arkin, Abulim; Yang Kunjie; Wang Shiheng; Shi Feiyue

2009-01-01

1.25 MeV γ-ray of 60 Co Compton scattering coefficient in the simple of paraffin,are measured by γ-ray energy spectrum analysis in two determining means. At the same experimental condition, we have used this scattering coefficient to determining grease thickness simulated by paraffin. The result show the average relative difference is about 1.29% for the best group. (authors)

46 CFR 282.23 - Hull and machinery insurance.

Science.gov (United States)

2010-10-01

... 46 Shipping 8 2010-10-01 2010-10-01 false Hull and machinery insurance. 282.23 Section 282.23... COMMERCE OF THE UNITED STATES Calculation of Subsidy Rates § 282.23 Hull and machinery insurance. (a) Subsidy items. The fair and reasonable net premium costs (including stamp taxes) of hull and machinery...

Analysis of the Effect of Injection Pressure on Ignition Delay and Combustion Process of Biodiesel from Palm Oil, Algae and Waste Cooking Oil

Science.gov (United States)

Irham Anas, Mohd; Khalid, Amir; Hakim Zulkifli, Fathul; Jaat, Norrizam; Faisal Hushim, Mohd; Manshoor, Bukhari; Zaman, Izzuddin

2017-10-01

Biodiesel is a domestically produced, renewable fuel that can be manufactured from vegetable oils, animal fats, or recycled restaurant grease for use in diesel engines. The objective of this research is investigation the effects of the variant injection pressure on ignition delay and emission for different biodiesel using rapid compression machine. Rapid Compression Machine (RCM) is used to simulate a single compression stroke of an internal combustion engine as a real engine. Four types of biodiesel which are waste cooking oil, crude palm oil, algae and jatropha were tested at injection pressure of 80 MPa, 90 MPa and 130 MPa under constant ambient temperature at 950 K. Increased in injection pressure resulted shorter ignition delay proven by WCO5 which decreased from 1.3 ms at 80 MPa to 0.7 ms at 130 MPa. Meanwhile, emission for CO2 increased due to better fuel atomization for fuel-air mixture formation lead to completed combustion.

Bacterial mitotic machineries

DEFF Research Database (Denmark)

Gerdes, Kenn; Møller-Jensen, Jakob; Ebersbach, Gitte

2004-01-01

Here, we review recent progress that yields fundamental new insight into the molecular mechanisms behind plasmid and chromosome segregation in prokaryotic cells. In particular, we describe how prokaryotic actin homologs form mitotic machineries that segregate DNA before cell division. Thus, the P......M protein of plasmid R1 forms F actin-like filaments that separate and move plasmid DNA from mid-cell to the cell poles. Evidence from three different laboratories indicate that the morphogenetic MreB protein may be involved in segregation of the bacterial chromosome.......Here, we review recent progress that yields fundamental new insight into the molecular mechanisms behind plasmid and chromosome segregation in prokaryotic cells. In particular, we describe how prokaryotic actin homologs form mitotic machineries that segregate DNA before cell division. Thus, the Par...

46 CFR 97.30-5 - Accidents to machinery.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Accidents to machinery. 97.30-5 Section 97.30-5 Shipping... Reports of Accidents, Repairs, and Unsafe Equipment § 97.30-5 Accidents to machinery. (a) In the event of an accident to a boiler, unfired pressure vessel, or machinery tending to render the further use of...

46 CFR 196.30-5 - Accidents to machinery.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Accidents to machinery. 196.30-5 Section 196.30-5... Reports of Accidents, Repairs, and Unsafe Equipment § 196.30-5 Accidents to machinery. (a) In the event of an accident to a boiler, unfired pressure vessel, or machinery tending to render the further use of...

Efficient production of biodiesel from waste grease: one-pot esterification and transesterification with tandem lipases.

Science.gov (United States)

Yan, Jinyong; Li, Aitao; Xu, Yi; Ngo, Thao P N; Phua, Szechao; Li, Zhi

2012-11-01

A novel concept and efficient method for producing biodiesel (FAME) from grease (15-40wt% free fatty acid, FFA) were developed by using tandem lipases for one-pot esterification of FFA and transesterification of triglyceride with methanol in a solvent-free system. Combining immobilized Candida antarctica lipase B (CALB) (Novozyme 435) favoring the esterification and immobilized Thermomyces lanuginosus lipase (TLL) (Lipozyme TLIM) preferring the transesterification at 2:8 (wt/wt) gave FAME in 80% yield, being better than that with Novozyme 435 or Lipozyme TLIM. Recombinant Escherichia coli (Calb/Tll) co-expressing CALB and TLL was engineered as a more efficient tandem-lipases system. Using wet or dry cells (4wt%) gave FAME in 87% or 95% yield, which is much better than that with E. coli cells expressing either CALB or TLL alone. Cells of E. coli (Calb/Tll) were recycled for five times and retained 75% productivity, thus being practical for producing biodiesel from grease. Copyright © 2012 Elsevier Ltd. All rights reserved.

Oil analysis in machine diagnostics

Energy Technology Data Exchange (ETDEWEB)

Vaehaeoja, P.

2006-07-01

This study concentrates on developing and tuning various oil analysis methods to meet the requirements of modern industry and environmental analytics. Oil analysis methods form a vital part of techniques used to monitor the condition of machines and may help to improve the overall equipment effectiveness value of a factory in a significant manner. Worm gears are used in various production machines, and their breakdowns may cause significant production losses. Wearing of these gears is relatively difficult to monitor with vibration analysis. Analysis of two indicator metals, copper and iron, may reveal wearing phenomena of worm gears effectively, and savings can be significant. Effective wear metal analysis requires good tools. ICP-OES with kerosene dilution is widely used in wear metal analysis, but purchasing and using of ICP-OES is expensive. A cheaper FAAS technique with similar pre-treatment of oil samples was tested and it proved to be useful especially in analyzing small amounts of samples. The accuracy of FAAS was sufficient for quantitative work in machine diagnostics and waste oil characterization. Solid debris analyses are useful in oil contamination control as well as in detection of wearing mechanisms. Membrane filtration, optical microscopy, SEM and automatic particle counting were applied in analysis of rolling and gear oils. Particle counting is an effective way to detect oil contamination, but in the studied cases even larger particles than those detected in normal ISO classes would be informative. However, membrane filtration and optical microscopy may reveal the wearing machine element exactly. Additives provide oils with desired properties thus they should be monitored intensively. A FTIR method for quantitative analysis of fatty alcohols and fatty acid esters in machinery oils was developed during this work. It has already been used successfully in quantitative and qualitative analysis of machinery oil samples. Various kinds of oils may be

Peak Oil, Food Systems, and Public Health

Science.gov (United States)

Parker, Cindy L.; Kirschenmann, Frederick L.; Tinch, Jennifer; Lawrence, Robert S.

2011-01-01

Peak oil is the phenomenon whereby global oil supplies will peak, then decline, with extraction growing increasingly costly. Today's globalized industrial food system depends on oil for fueling farm machinery, producing pesticides, and transporting goods. Biofuels production links oil prices to food prices. We examined food system vulnerability to rising oil prices and the public health consequences. In the short term, high food prices harm food security and equity. Over time, high prices will force the entire food system to adapt. Strong preparation and advance investment may mitigate the extent of dislocation and hunger. Certain social and policy changes could smooth adaptation; public health has an essential role in promoting a proactive, smart, and equitable transition that increases resilience and enables adequate food for all. PMID:21778492

Optimization of advanced liquid natural gas-fuelled machineries for a high-speed ferry

DEFF Research Database (Denmark)

Tveitaskog, Kari Anne; Haglind, Fredrik

-based optimization routine are used. The top cycle is modeled as the aero-derivative gas turbine LM2500, while the following five options for bottoming cycles are modeled: ∙ Single pressure steam cycle ∙ Dual-pressure steam cycle ∙ ORC using Toluene as the working fluid with an intermediate oil loop ∙ ABC with inter......This report is aimed at designing and optimizing combined cycles in order to define the most suitable machinery system for the future high-speed Incat ferry operated by Mols-Linien. For this purpose, an in-house numerical simulation tool called DNA (Dynamic Network Analysis) and a genetic algorithm...

Levels of Petroleum Hydrocarbons and some Heavy Metals in ...

African Journals Online (AJOL)

Michael Horsfall

has outlets to the Atlantic Ocean. The river which supports major commercial ... acidification. Oils and solids or viscous grease present were separated from liquid samples by filtration. After extraction, the residue after solvent evaporation was weighed to determine the oil and grease content. Compounds volatilized at or ...

Monitoring, characterization and comparison. Operation-project of oil and oil water systems in platforms

International Nuclear Information System (INIS)

P Junior, Oswaldo A.; Louvisse, Ana M.T.; Ramalho, Joao B.V.S.; Miragaya, Jose C.G.

2000-01-01

During the process of petroleum production, water are also commonly produced. Usually, a standard oil-water separation process will not lead to water phase ready to be discharged - the present legislation requires oily contents (oil and/or greases) bellow 20 mg/L concentration level value. Thus, secondary treatment is required to bring such oily concentration to the allowed level or lower, prior to the water discard in the environment. This paper describes the adopted systematic work in the Campos Basin Petroleum Production Platforms, which has allowed to evaluate and optimize the water treatment performed in there. Such description includes the typical water treatment systems installed, the typical physical-chemistry of the effluents and also presents comparisons between the basic designs that guided such systems construction and their present operational conditions and set-ups. The analysis of such results has allowed the introduction of minor modifications leading to the process optimization. The common use of Pilot Plants in such optimization process is also described and their contribution reported. (author)

Greasing the Wheels of Trade: measuring the Dutch transaction with occupational data

OpenAIRE

Dalen, Hendrik; Vuuren, Aico

2003-01-01

textabstractHow much does a nation spend on resources to 'grease the wheels of trade'? To examine this question the Dutch economy is used as an exemplary case as the Netherlands are known as a nation of traders. This image was derived in the seventeenth century from successes in long distance trade, shipping and financial innovations. Despite its historical background in trading the potential to 'truck and barter' has never been adequately measured. In this paper we present a first attempt in...

Influence of Brazilian vegetable oils on mechanical resistence of hair fiber

Directory of Open Access Journals (Sweden)

Maria Valéria Velasco

2015-02-01

Full Text Available Associating the global trend of incorporating active compounds and plants in cosmetic formulations and the vast Brazilian biodiversity, the present work aimed to study the incorporation of Brazilian vegetable oils in hair conditioner formulations, evaluating the mechanical resistance of hair fibers. The following oils were incorporated into base formulations at 5.0 % (w/w: babassu, buriti, andiroba and pequi. The formulations were applied to samples of Caucasian hair, followed by several washing steps, then the evaluation of mechanical strength. It was found that there was no statistically significant difference in mechanical resistance between samples treated with oils and the control between the first and seventh wash cycles. This fact can be explained by the possible low penetration of oils into the cortex, a region responsible for the mechanical properties of the hair fiber, since the grease composition disfavors its diffusion. The common effects of vegetable oils on the cuticle, such as filling in cracks or cavities, lubrication, and increased protein hydrophobicity cannot be excluded. The oils tested in this work were not able to raise or protect hair tresses. However, additional studies are required in order to establish the effects of oil treatments, particularly in damaged hair.

46 CFR 109.205 - Inspection of boilers and machinery.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Inspection of boilers and machinery. 109.205 Section 109... OPERATIONS Tests, Drills, and Inspections § 109.205 Inspection of boilers and machinery. The chief engineer or engineer in charge, before he assumes charge of the boilers and machinery of a unit shall inspect...

Solar Alpha Rotary Joint (SARJ) Lubrication Interval Test and Evaluation (LITE). Post-Test Grease Analysis

Science.gov (United States)

Golden, Johnny L.; Martinez, James E.; Devivar, Rodrigo V.

2015-01-01

The Solar Alpha Rotary Joint (SARJ) is a mechanism of the International Space Station (ISS) that orients the solar power generating arrays toward the sun as the ISS orbits our planet. The orientation with the sun must be maintained to fully charge the ISS batteries and maintain all the other ISS electrical systems operating properly. In 2007, just a few months after full deployment, the starboard SARJ developed anomalies that warranted a full investigation including ISS Extravehicular Activity (EVA). The EVA uncovered unexpected debris that was due to degradation of a nitride layer on the SARJ bearing race. ISS personnel identified the failure root-cause and applied an aerospace grease to lubricate the area associated with the anomaly. The corrective action allowed the starboard SARJ to continue operating within the specified engineering parameters. The SARJ LITE (Lubrication Interval Test and Evaluation) program was initiated by NASA, Lockheed Martin, and Boeing to simulate the operation of the ISS SARJ for an extended time. The hardware was designed to test and evaluate the exact material components used aboard the ISS SARJ, but in a controlled area where engineers could continuously monitor the performance. After running the SARJ LITE test for an equivalent of 36+ years of continuous use, the test was opened to evaluate the metallography and lubrication. We have sampled the SARJ LITE rollers and plate to fully assess the grease used for lubrication. Chemical and thermal analysis of these samples has generated information that has allowed us to assess the location, migration, and current condition of the grease. The collective information will be key toward understanding and circumventing any performance deviations involving the ISS SARJ in the years to come.

46 CFR 185.208 - Accidents to machinery.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Accidents to machinery. 185.208 Section 185.208 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) OPERATIONS Marine Casualties and Voyage Records § 185.208 Accidents to machinery. The owner, managing...

46 CFR 122.208 - Accidents to machinery.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Accidents to machinery. 122.208 Section 122.208 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS CARRYING MORE THAN 150... Voyage Records § 122.208 Accidents to machinery. The owner, managing operator, or master shall report...

Climate design of vegetable oil fuels for agricultural equipment; Klimadesign von Pflanzenoelkraftstoffen fuer landwirtschaftliche Maschinen

Energy Technology Data Exchange (ETDEWEB)

Stoehr, Michael [B.A.U.M. Consult GmbH, Muenchen (Germany). International and Energy Projects; Pickel, Peter [John Deere European Technology Innovation Center, Kaiserslautern (Germany)

2012-07-01

The use of biofuels in agricultural machinery is an option for complying with climate protection requirements that are presently discussed to be placed on manufacturers of mobile off-road machinery by the European Commission. A mathematical model has been developed that allows calculating greenhouse gas emissions (GHGE) of biofuels for complex production paths in a straightforward, transparent manner and in pattern with the EU's Fuel Quality Directive (FQD). Therewith it has been shown that both rape seed and camelina sativa oil fuels can save more than 60 % GHGE. Key parameters have been identified and rules for a climate design of vegetable oil fuels have been formulated. (orig.)

29 CFR 1915.164 - Ship's propulsion machinery.

Science.gov (United States)

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Ship's propulsion machinery. 1915.164 Section 1915.164 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) OCCUPATIONAL SAFETY AND HEALTH STANDARDS FOR SHIPYARD EMPLOYMENT Ship's Machinery and Piping Systems § 1915.164 Ship's...

Thermophilic anaerobic co-digestion of sewage sludge with grease waste: Effect of long chain fatty acids in the methane yield and its dewatering properties

International Nuclear Information System (INIS)

Silvestre, G.; Illa, J.; Fernández, B.; Bonmatí, A.

2014-01-01

Highlights: • Thermophilic anaerobic codigestion of sewage sludge and grease waste (GW) doubles methane yield. • High GW doses in the influent leads to instability and LCFA accumulation in the effluent. • GW addition promotes acetoclastic activity whilst worsening the hydrogenothrophic activity. • The mesophilic codigestion with GW performs better than the thermophilic one. - Abstract: Thermophilic co-digestion of sewage sludge with three different doses of trapped grease waste (GW) from the pre-treatment of a WWTP has been assessed in a CSTR bench-scale reactor. After adding 12% and 27% of grease waste (on COD basis), the organic loading rate increased from 2.2 to 2.3 and 2.8 kg COD m −3 d −1 respectively, and the methane yield increased 1.2 and 2.2 times. Further GW increase (37% on COD basis) resulted in an unstable methane yield and in long chain fatty acids (LCFA) accumulation. Although this inestability, the presence of volatile fatty acids in the effluent was negligible, showing good adaptation to fats of the thermophilic biomass. Nevertheless, the presence of LCFA in the effluent worsens its dewatering properties. Specific methanogenic activity tests showed that the addition of grease waste ameliorates the acetoclastic activity in detriment of the hydrogenotrophic activity, and suggests that the tolerance to LCFA can be further enhanced by slowly increasing the addition of lipid-rich materials

78 FR 14457 - Guidelines Establishing Test Procedures for the Analysis of Pollutants Under the Clean Water Act...

Science.gov (United States)

2013-03-06

... discharge limits. Method 1664A is a liquid/liquid extraction (LLE), gravimetric procedure that employs...: EPA discussed, but did not propose, a new method, ASTM D7575, for oil and grease in the 2010 proposed Methods Update Rule (MUR). Oil and grease is a method-defined parameter. That is, the nature and amount of...

Friction, Wear, and Evaporation Rates of Various Materials in Vacuum to 10(exp -7) mm Hg

Science.gov (United States)

Buckley, Donald H.; Swikert, Max; Johnson, Robert L.

1961-01-01

The requirements for bearings and seals to operate in the environment of space dictate a new area for lubrication research. The low ambient pressures encountered in space can be expected to influence the behavior of oil, grease, and solid-film lubricants. The property of these materials most significantly affected by low ambient pressures is the evaporation rate. Various investigators have therefore measured the evaporation rates of oils and greases in vacuum as one method of establishing their relative merit for space applications (1-3). The results of this work have given some indication as to the oils and greases with the greatest stability at reduced ambient pressures. Only limited experimental work, however, has been reported in the literature for inorganic solids and soft metals which have potential use as solid lubricant films or coatings for hard alloy substrates [e.g. Reference ( 4 )]. In general, the evaporation rates of these materials would be lower than those of oils and greases. These films might therefore be very attractive as lubricants for high vacuum service.

Review of inservice inspections of greased tendons in prestressed-concrete containments

International Nuclear Information System (INIS)

Dougan, J.R.; Ashar, H.

1983-01-01

Prestressed-concrete containments in the United States using greased prestressing tendons are inspected periodically to ensure structural integrity and to identify and correct problem areas before they become critical. An analysis of the available utility inspection data and an evaluation of the current and proposed guidelines were conducted to provide a measure of the reliability of the inspection process. Comments from utility and industry personnel were factored into the analysis. The results indicated that the majority of the few incidences of problems or abnormalities which occurred were minor in nature and did not threaten the structural integrity of the containment

Vibration vector monitoring of rotating machinery: A predictive/preventative maintenance technique

International Nuclear Information System (INIS)

Humes, B.R.

1990-01-01

Monitoring of overall vibration amplitudes to indicate machinery faults is a standard practice in most industries. The appearance of shaft cracks in machines retrofitted for extended life have prompted development of higher levels of machinery monitoring. Part 1 of this paper discusses vibration vector monitoring for machinery malfunction prediction and failure prevention. Machinery faults which can be diagnosed by this type of monitoring, such as rotor rubs, loose parts, shaft cracks, ..., are presented along with their most common characteristics. The newest, most effective methods of permanent machinery monitoring are presented and critiqued. An extensive case history is presented in Part 2 in which a potentially disastrous machinery fault was predicted using vibration vector monitoring and analysis. The addition of vector monitoring to the normal, overall vibration monitoring proved more effective in diagnosing the machinery fault and predicting impending failure

Biodiesel production from Jatropha curcas oil

Energy Technology Data Exchange (ETDEWEB)

Jain, Siddharth; Sharma, M.P. [Alternate Hydro Energy Centre, Indian Institute of Technology Roorkee, Roorkee, Uttarakhand 247667 (India)

2010-12-15

In view of the fast depletion of fossil fuel, the search for alternative fuels has become inevitable, looking at huge demand of diesel for transportation sector, captive power generation and agricultural sector, the biodiesel is being viewed a substitute of diesel. The vegetable oils, fats, grease are the source of feedstocks for the production of biodiesel. Significant work has been reported on the kinetics of transesterification of edible vegetable oils but little work is reported on non-edible oils. Out of various non-edible oil resources, Jatropha curcas oil (JCO) is considered as future feedstocks for biodiesel production in India and limited work is reported on the kinetics of transesterification of high FFA containing oil. The present study reports a review of kinetics of biodiesel production. The paper also reveals the results of kinetics study of two-step acid-base catalyzed transesterification process carried out at pre-determined optimum temperature of 65 and 50 C for esterification and transesterification process, respectively, under the optimum condition of methanol to oil ratio of 3:7 (v/v), catalyst concentration 1% (w/w) for H{sub 2}SO{sub 4} and NaOH and 400 rpm of stirring. The yield of methyl ester (ME) has been used to study the effect of different parameters. The maximum yield of 21.2% of ME during esterification and 90.1% from transesterification of pretreated JCO has been obtained. This is the first study of its kind dealing with simplified kinetics of two-step acid-base catalyzed transesterification process carried at optimum temperature of both the steps which took about 6 h for complete conversion of TG to ME. (author)

Lipase-producing fungi for potential wastewater treatment and ...

African Journals Online (AJOL)

The use of fungal biomass as a lipase biocatalyst represents an attractive approach for the treatments of oil wastewater as well as for the production of biodiesel from oil and residual grease, due to its greater stability, possibility of reuse, and lower cost. In this work, 20 filamentous fungi were isolated from the grease trap ...

Preliminary detection of native lipase producing microorganisms for bio diesel production

International Nuclear Information System (INIS)

Ciudad, G.; Jorquera, M.; Briones, R.; Azocar, L.; Leal, J.; Navia, R.

2009-01-01

Lipase producing microorganisms (LPM) may catalyze the hydrolysis or transesterification of triacylglycerols to alkyl esters of fatty acids (bio diesel). The main objective of this work was to detect LPM in oil and grease contaminated environments for future applications in bio diesel production from rapeseed oil. Samples from contaminated soil (with rapeseed oil) from an industrial facility and contaminated soil (with salmon grease) near to a fish wastewater treatment plant were collected. (Author)

Preliminary detection of native lipase producing microorganisms for bio diesel production

Energy Technology Data Exchange (ETDEWEB)

Ciudad, G.; Jorquera, M.; Briones, R.; Azocar, L.; Leal, J.; Navia, R.

2009-07-01

Lipase producing microorganisms (LPM) may catalyze the hydrolysis or transesterification of triacylglycerols to alkyl esters of fatty acids (bio diesel). The main objective of this work was to detect LPM in oil and grease contaminated environments for future applications in bio diesel production from rapeseed oil. Samples from contaminated soil (with rapeseed oil) from an industrial facility and contaminated soil (with salmon grease) near to a fish wastewater treatment plant were collected. (Author)

Risk assessments and safe machinery ensuring compliance with the EU directives

CERN Document Server

Jespen, Torben

2016-01-01

This book describes the prerequisites for the placing on the market and the safe use of machinery in compliance with the relevant EU Directives, especially the Machinery Directive 2006/42. It provides readers with high-level knowledge concerning the Essential Health and Safety Requirements (EHSR) that machinery must fulfill. The approach and principles of the Machinery Directive were most recently made worldwide acknowledged in the ILO code of practice on safe machinery, released in 2013. The book addresses that code, as well as providing valuable insight into other EU Product and Workplace legislation. Focusing on the key aspect of safe machinery, the “machinery safety risk assessment”, which allows readers to better understand the more difficult aspects of risk assessments, the book equips readers to tackle problems at the manufacturing stage and in different use scenarios, introducing them to risk reduction techniques and functional safety aspects.

46 CFR 182.465 - Ventilation of spaces containing diesel machinery.

Science.gov (United States)

2010-10-01

... furnish natural or powered supply and exhaust ventilation. The total inlet area and the total outlet area... 46 Shipping 7 2010-10-01 2010-10-01 false Ventilation of spaces containing diesel machinery. 182... Ventilation of spaces containing diesel machinery. (a) A space containing diesel machinery must be fitted with...

The Research of Computer Aided Farm Machinery Designing Method Based on Ergonomics

Science.gov (United States)

Gao, Xiyin; Li, Xinling; Song, Qiang; Zheng, Ying

Along with agricultural economy development, the farm machinery product type Increases gradually, the ergonomics question is also getting more and more prominent. The widespread application of computer aided machinery design makes it possible that farm machinery design is intuitive, flexible and convenient. At present, because the developed computer aided ergonomics software has not suitable human body database, which is needed in view of farm machinery design in China, the farm machinery design have deviation in ergonomics analysis. This article puts forward that using the open database interface procedure in CATIA to establish human body database which aims at the farm machinery design, and reading the human body data to ergonomics module of CATIA can product practical application virtual body, using human posture analysis and human activity analysis module to analysis the ergonomics in farm machinery, thus computer aided farm machinery designing method based on engineering can be realized.

Performance of refrigerating machineries with new refrigerants; Performance des machines frigorifiques avec les nouveaux refrigerants

Energy Technology Data Exchange (ETDEWEB)

Bailly, A; Jurkowski, R [CIAT, 01 - Culoz (France)

1998-12-31

This paper reports on a comparative study of the thermal performances of different refrigerants like R-22, R-134a, R-404A and R-407C when used as possible substitutes for the HCFC22 refrigerant in a given refrigerating machinery equipped with compact high performance plate exchangers. Thermal performances are compared in identical operating conditions. The behaviour of the two-phase exchange coefficient is analyzed with respect to the different parameters. The composition of the mixture after one year of operation has been analyzed too and the influence of oil on the performances is studied. (J.S.)

Performance of refrigerating machineries with new refrigerants; Performance des machines frigorifiques avec les nouveaux refrigerants

Energy Technology Data Exchange (ETDEWEB)

Bailly, A.; Jurkowski, R. [CIAT, 01 - Culoz (France)

1997-12-31

This paper reports on a comparative study of the thermal performances of different refrigerants like R-22, R-134a, R-404A and R-407C when used as possible substitutes for the HCFC22 refrigerant in a given refrigerating machinery equipped with compact high performance plate exchangers. Thermal performances are compared in identical operating conditions. The behaviour of the two-phase exchange coefficient is analyzed with respect to the different parameters. The composition of the mixture after one year of operation has been analyzed too and the influence of oil on the performances is studied. (J.S.)

46 CFR 97.15-15 - Examination of boilers and machinery.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Examination of boilers and machinery. 97.15-15 Section... VESSELS OPERATIONS Tests, Drills, and Inspections § 97.15-15 Examination of boilers and machinery. It shall be the duty of the chief engineer when assuming charge of the boilers and machinery of a vessel to...

46 CFR 32.35-1 - Boilers and machinery-TB/ALL.

Science.gov (United States)

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Boilers and machinery-TB/ALL. 32.35-1 Section 32.35-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS SPECIAL EQUIPMENT, MACHINERY, AND HULL REQUIREMENTS Main and Auxiliary Machinery § 32.35-1 Boilers and machinery—TB/ALL. Boilers, main and auxiliary...

46 CFR 78.17-30 - Examination of boilers and machinery.

Science.gov (United States)

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Examination of boilers and machinery. 78.17-30 Section... OPERATIONS Tests, Drills, and Inspections § 78.17-30 Examination of boilers and machinery. It shall be the duty of the chief engineer when assuming charge of the boilers and machinery of a vessel to examine...

Machinery condition monitoring principles and practices

CERN Document Server

Mohanty, Amiya Ranjan

2015-01-01

Find the Fault in the MachinesDrawing on the author's more than two decades of experience with machinery condition monitoring and consulting for industries in India and abroad, Machinery Condition Monitoring: Principles and Practices introduces the practicing engineer to the techniques used to effectively detect and diagnose faults in machines. Providing the working principle behind the instruments, the important elements of machines as well as the technique to understand their conditions, this text presents every available method of machine fault detection occurring in machines in general, an

Handbook of vacuum physics

CERN Document Server

1964-01-01

Handbook of Vacuum Physics, Volume 3: Technology is a handbook of vacuum physics, with emphasis on the properties of miscellaneous materials such as mica, oils, greases, waxes, and rubber. Accurate modern tables of physical constants, properties of materials, laboratory techniques, and properties of commercial pumps, gauges, and leak detectors are presented. This volume is comprised of 12 chapters and begins with a discussion on pump oils, divided into rotary pump oils and vapor pump oils. The next chapter deals with the properties and applications of greases, including outgassing and vapor pr

46 CFR 196.15-15 - Examination of boilers and machinery.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Examination of boilers and machinery. 196.15-15 Section... VESSELS OPERATIONS Test, Drills, and Inspections § 196.15-15 Examination of boilers and machinery. (a) It shall be the duty of the chief engineer when he assumes charge of the boilers and machinery of a vessel...

Vibration of hydraulic machinery

CERN Document Server

Wu, Yulin; Liu, Shuhong; Dou, Hua-Shu; Qian, Zhongdong

2013-01-01

Vibration of Hydraulic Machinery deals with the vibration problem which has significant influence on the safety and reliable operation of hydraulic machinery. It provides new achievements and the latest developments in these areas, even in the basic areas of this subject. The present book covers the fundamentals of mechanical vibration and rotordynamics as well as their main numerical models and analysis methods for the vibration prediction. The mechanical and hydraulic excitations to the vibration are analyzed, and the pressure fluctuations induced by the unsteady turbulent flow is predicted in order to obtain the unsteady loads. This book also discusses the loads, constraint conditions and the elastic and damping characters of the mechanical system, the structure dynamic analysis, the rotor dynamic analysis and the system instability of hydraulic machines, including the illustration of monitoring system for the instability and the vibration in hydraulic units. All the problems are necessary for vibration pr...

46 CFR 78.33-5 - Accidents to machinery.

Science.gov (United States)

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Accidents to machinery. 78.33-5 Section 78.33-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS OPERATIONS Reports of Accidents, Repairs, and Unsafe Equipment § 78.33-5 Accidents to machinery. (a) In the event of an accident...

Open innovation and supply chain management in food machinery ...

African Journals Online (AJOL)

Open innovation and supply chain management in food machinery supply chain: a ... This paradigm describes a new approach to internal R&D management, which ... a picture of the adoption of open innovation in the food machinery industry.

46 CFR 169.629 - Compartments containing gasoline machinery or fuel tanks.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Compartments containing gasoline machinery or fuel tanks. 169.629 Section 169.629 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL... gasoline machinery or fuel tanks. Spaces containing gasoline machinery or fuel tanks must have natural...

Rheology of oleo gels based on sorbitan and glyceryl mono stearates and vegetable oils for lubricating applications

Energy Technology Data Exchange (ETDEWEB)

Sanchez, R.; Franco, J. M.; Delgado, M. A.; Valencia, C.; Gallegos, C.

2011-07-01

Oleo gels based on sorbitan and glyceryl mono stearates and different types of vegetable oils, potentially applicable as biodegradable alternatives to traditional lubricating greases, have been studied. In particular, the rheological behavior, by means of small-amplitude oscillatory shear (SAOS) measurements, and some lubrication performance-related properties (mechanical stability and tribological response) have been evaluated in this work. SAOS response and mechanical stability of these oleo gels are significantly influenced by the type and concentration of the organogelator and the vegetable oil used in the formulations. Glyceryl monostearate (GMS) generally produces stronger gels than sorbitan monostearate (SMS). The use of low-viscosity oils, such as rapeseed and soybean oils, yields gels with significantly higher values of the linear viscoelastic functions than oleo gels prepared with high-viscosity oils, i.e. castor oil. The rheological behavior of SMS-based oleo gels also depends on the cooling rate applied during the gelification process. On the other hand, the oleo gels studied present low values of the friction coefficient obtained in a tribological contact, although only some GMS/castor oil-based oleo gels exhibit a suitable mechanical stability. (Author) 28 refs.

46 CFR 116.620 - Ventilation of machinery and fuel tank spaces.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Ventilation of machinery and fuel tank spaces. 116.620... AND ARRANGEMENT Ventilation § 116.620 Ventilation of machinery and fuel tank spaces. In addition to the requirements of this subpart, ventilation systems for spaces containing machinery or fuel tanks...

Synthesis and chemical modification of polymeric resins for the treatment of cations and aromatic hydrocarbons in produced oily water; Sintese de modificacao quimica de resina polimerica e aplicacao na remocao de cations e hidrocarbonetos aromaticos presentes em agua produzida

Energy Technology Data Exchange (ETDEWEB)

Aversa, Thiago M.; Rodrigues, Monique F.; Vieira, Helida V.P.; Queiros, Yure G.C.; Lucas, Elizabete F. [Universidade Federal do Rio de Janeiro, Instituto de Macromoleculas, Lab. de Macromoleculas e Coloides na Industria do Petroleo, Rio de Janeiro, RJ (Brazil)], e-mail: thiagoaversa@ima.ufrj.br

2011-07-01

The use of chemically modified resins in oily water treatment process is not very developed yet. Because of this, this work suggests to study the styrene and divinylbenzene sulfonation effect on oil and grease, aniline and calcium removal from the water. The aniline, oils and greases belong to a class of toxic organic compounds, with the Brazilian maximum limits established for disposal in CONAMA 393/2007, while the calcium ions belong to the group of cations of alkaline earth metals which improve hardness to the water, may cause fouling as carbonates and sulfates form. By using sulfonated resins in oily water treatment it is possible to remove not only oils and greases but also calcium and aniline. These kinds of polar compounds are removed because of the cation exchange capacity of resin. (author)

46 CFR 91.15-1 - Standards in inspection of hulls, boilers, and machinery.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Standards in inspection of hulls, boilers, and machinery... hulls, boilers, and machinery. In the inspection of hulls, boilers, and machinery of vessels, the..., respecting material and inspection of hulls, boilers, and machinery, and the certificate of classification...

46 CFR 189.15-1 - Standards in inspection of hulls, boilers, and machinery.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Standards in inspection of hulls, boilers, and machinery... inspection of hulls, boilers, and machinery. In the inspection of hulls, boilers, and machinery of vessels... chapter, respecting material and construction of hulls, boilers, and machinery, and certificate of...

46 CFR 71.15-1 - Standards in inspection of hulls, boilers, and machinery.

Science.gov (United States)

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Standards in inspection of hulls, boilers, and machinery..., boilers, and machinery. In the inspection of hulls, boilers, and machinery of vessels, the standards... and inspection of hulls, boilers, and machinery, and the certificate of classification referring...

Development of high performance lubricant through the compatibilization of polyalphaolefin, polyurea and irradiated polytetrafluoroethylene

International Nuclear Information System (INIS)

Ratao, Natalia T.; Zen, Heloisa A.; Lugao, Ademar B.

2013-01-01

High performance lubricants are essential for shipping and oil exploration industries for working under severe conditions of temperature, pressure and contamination. Polytetrafluoroethylene (PTFE) is widely used as a lubricating additive in greases for presenting the lowest known coefficient of friction, is commercially found irradiated in air, by this way can be grinded and oxygenated terminal groups can be formed. PTFE processed by ionizing radiation with 4μ average particle size was supplied by Uniflon and compared with the ultraviolet-irradiated PTFE with the same average particle size, from Dupont. The characterization of functional proprieties by drop point, oil separation and four ball test was conducted with a polyurea base grease additive with both types of PTFE. The chemical characterization was done with Differential Scanning Calorimetry (DSC). The drop point and oil separation tests showed that the Uniflon irradiated PTFE improved the thermal resistance and stability of polyurea grease due to the greater presence of the end groups increase the compatibility of the additive with the fluid. Four ball tests showed that the grease with Uniflon irradiated PTFE also has a better antiwear and extreme pressure performance because of the greater polarity of the molecules improving the dispersion and anchoring of the PTFE in metal surface voids, reducing wear. The PTFE processed by ionizing radiation showed greater compatibility with polyurea grease and polyalphaolefin fluid and the grease functional characteristics met the requirements for a high performance lubricant. (author)

Decontamination flowsheet development for a waste oil containing mixed radioactive contaminants

International Nuclear Information System (INIS)

Vijayan, S.; Buckley, L.P.

1993-01-01

The majority of waste oils contaminated with both radioactive and hazardous components are generated in nuclear power plant, research lab. and uranium-refinery operations. The waste oils are complex, requiring a detailed examination of the waste management strategies and technology options. It may appear that incineration offers a total solution, but this may not be true in all cases. An alternative approach is to decontaminate the waste oils to very low contaminant levels, so that the treated oils can be reused, burned as fuel in boilers, or disposed of by commercial incineration. This paper presents selected experimental data and evaluation results gathered during the development of a decontamination flowsheet for a specific waste oil stores at Chalk River Labs. (CRL). The waste oil contains varying amounts of lube oils, grease, paint, water, particulates, sludge, light chloro- and fluoro-solvents, polychlorinated biphenyls (PCB), complexing chemicals, uranium, chromium, iron, arsenic and manganese. To achieve safe management of this radioactive and hazardous waste, several treatment and disposal methods were screened. Key experiments were performed at the laboratory-scale to confirm and select the most appropriate waste-management scheme based on technical, environmental and economic criteria. The waste-oil-decontamination flowsheet uses a combination of unit operations, including prefiltration, acid scrubbing, and aqueous-leachage treatment by precipitation, microfiltration, filter pressing and carbon adsorption. The decontaminated oil containing open-quotes de minimisclose quotes levels of contaminants will undergo chemical destruction of PCBs and final disposal by incineration. The recovered uranium will be recycled to a uranium milling process

40 CFR 419.42 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Science.gov (United States)

2010-07-01

... Process category Process included Weighting factor Crude Atm crude distillationVacuum, crude distillation... 360.0 187.0 Oil and grease 16.2 8.5 Phenolic compounds 0.38 0.184 Ammonia as N 23.4 10.6 Sulfide 0.33... 1,000 bbl of feedstock) BOD5 17.9 9.1 TSS 12.5 8.0 COD 1 127.0 66.0 Oil and grease 5.7 3.0 Phenolic...

49 CFR 1242.47 - Machinery (account XX-27-40).

Science.gov (United States)

2010-10-01

... 49 Transportation 9 2010-10-01 2010-10-01 false Machinery (account XX-27-40). 1242.47 Section 1242...-Equipment § 1242.47 Machinery (account XX-27-40). Separate common expenses on the basis of the freight/passenger separation of administration (account XX-27-01). ...

Application of biomass in oil and fat reduction content in aqueous effluent; Aplicacao de biomassa na reducao do teor de oleos e graxas presentes em efluentes aquosos

Energy Technology Data Exchange (ETDEWEB)

Boni, Hevelin Tabata; Souza, Antonio Augusto Ulson de; Souza, Selene Maria de Arruda Guelli Ulson de [Universidade Federal de Santa Catarina (UFSC), SC (Brazil)

2012-07-01

In this work, we have studied the bagasse from sugarcane as an alternative bioadsorbent in the treatment to oils and greases contaminated waters. The synthetic effluent was simulated by a distilled water and decahydronaphthalene dispersion, with initial concentration of 8900 mg . L {sup -1}. Gas chromatography was the analytical operation chosen to quantify the oil residual after the adsorption. The biomass was characterized by moisture analysis, CHNS and SEM. The experiments were carried out in batch process with agitation of 120 rpm, evaluating the equilibrium time of adsorptive process and the influence of pH of aqueous level. Results showed that the adsorption process achieved equilibrium quickly, in just 5 minutes of contact between the dispersion and biomass. No significant influence was noticed in the removal of hydrocarbon with the change in pH. The adsorption isotherm was developed changing by the mass of bioadsorbent, at 25 deg C, pH 6 and 120 rpm of agitation. The experimental results were fitted by Langmuir and Langmuir- Freundlich models. The best fit was obtained with Langmuir-Freundlich, providing a maximum adsorption capacity of 6,65 g hydrocarbon / g biomass. The experiments showed the great potential of the sugarcane bagasse to be used as bioadsorbent in reducing the oil and grease levels in industrial effluents. This alternative presents itself as a sustainable route due to the abundance of sugar cane bagasse in the sugar and alcohol industry, avoided the impact of aqueous sources contamination coming from oil and petrochemical industry. (author)

Study on the Tribological Properties of MC Nylon Composites Filled with Hydraulic Oil

Science.gov (United States)

Yuan, S.; Li, Y.; Wen, J.; Yin, L.; Zhang, Q.

2018-03-01

Mechanical parts utilized in machinery, such as nylon slider and pulley, should have certain mechanical properties and good tribological properties, so that equipments’ stability and smoothness can be assured. A kind of MC nylon (monomer cast nylon) composites filled with hydraulic oil was studied in this paper. The addition of hydraulic oil changed nylon’s mechanical properties and tribological properties significantly, and improved the material’s toughness and coefficient of friction. The composites have excellent strength, toughness and relatively low coefficient of friction when the content of the hydraulic oil is 4wt%.

46 CFR 169.315 - Ventilation (other than machinery spaces).

Science.gov (United States)

2010-10-01

... section is satisfied, a vessel having only a natural ventilation system must satisfy the following: V/A≥1... 46 Shipping 7 2010-10-01 2010-10-01 false Ventilation (other than machinery spaces). 169.315... SCHOOL VESSELS Construction and Arrangement Hull Structure § 169.315 Ventilation (other than machinery...

Optical coupling study of plastic scintillation detectors: evaluation of different silicon products

International Nuclear Information System (INIS)

Hamada, M.M.; Madi Filho, T.; Mesquita, C.H. de

1990-01-01

Properties of different optical oils and greases in the range of 320-560 nm were studied. Several parameters as the transmitance, index of refraction, plastic scintillator fluorescence emission and its influence in the resolution and pulse height of the detection system were described. This paper shows a design to analyse the optical quality or adequacy of the silicon oils and greases in the coupling between the detector and the photocathode of the photomultiplier. (author) [pt

Stream Management

Science.gov (United States)

2000-03-01

from coconut husks bound within a woven mesh rope either made from polyethylene or coir rope. The CGR incorporates wetland plants (usually as rooted...Process 6-1 Nonrestoration Alternative Considerations 6-3 Stormwater ponds 6-4 Infiltration (exfiltration) devices 6-6 Oil and grease trap devices 6-8... Oil and Grease Trap Pollutant Removal 6-9 Table 6.4. Sand Filter Pollutant Removal 6-11 Table 6.5. Selection of Appropriate Structural Solutions

40 CFR 112.13-112.15 - [Reserved

Science.gov (United States)

2010-07-01

... POLLUTION PREVENTION Requirements for Animal Fats and Oils and Greases, and Fish and Marine Mammal Oils; and for Vegetable Oils, including Oils from Seeds, Nuts, Fruits, and Kernels. §§ 112.13-112.15 [Reserved] ...

40 CFR 180.521 - Fumigants for grain-mill machinery; tolerances for residues.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Fumigants for grain-mill machinery... Tolerances § 180.521 Fumigants for grain-mill machinery; tolerances for residues. (a) General. Fumigants may be safely used in or on grain-mill machinery in accordance with the following prescribed conditions...

Genome-scale modeling of the protein secretory machinery in yeast

DEFF Research Database (Denmark)

Feizi, Amir; Österlund, Tobias; Petranovic, Dina

2013-01-01

The protein secretory machinery in Eukarya is involved in post-translational modification (PTMs) and sorting of the secretory and many transmembrane proteins. While the secretory machinery has been well-studied using classic reductionist approaches, a holistic view of its complex nature is lacking....... Here, we present the first genome-scale model for the yeast secretory machinery which captures the knowledge generated through more than 50 years of research. The model is based on the concept of a Protein Specific Information Matrix (PSIM: characterized by seven PTMs features). An algorithm...

Machinery failure analysis and troubleshooting practical machinery management for process plants

CERN Document Server

Bloch, Heinz P

2012-01-01

Solve the machinery failure problems costing you time and money with this classic, comprehensive guide to analysis and troubleshooting  Provides detailed, complete and accurate information on anticipating risk of component failure and avoiding equipment downtime Includes numerous photographs of failed parts to ensure you are familiar with the visual evidence you need to recognize Covers proven approaches to failure definition and offers failure identification and analysis methods that can be applied to virtually all problem situations Demonstr

Radiation technologies in metallurgy and machinery

International Nuclear Information System (INIS)

Meshkov, I.N.

1990-01-01

Applications of electron beam accelerators for technologies in metallurgy and machinery are discussed. Processes described are provided with special industrial accelerators, developed in the Institute of Nuclear Physics, Novosibirsk. (author)

FOREWORD: 26th IAHR Symposium on Hydraulic Machinery and Systems

Science.gov (United States)

Wu, Yulin; Wang, Zhengwei; Liu, Shuhong; Yuan, Shouqi; Luo, Xingqi; Wang, Fujun

2012-11-01

The 26th IAHR Symposium on Hydraulic Machinery and Systems, will be held in Beijing, China, 19-23 August 2012. It is jointly organized by Tsinghua University, State Key Laboratory of Hydro Science and Hydraulic Engineering, China, Jiangsu University, Xi'an University of Technology, China Agricultural University, National Engineering Research Center of Hydropower Equipment and Dongfang Electric Machinery Co., Ltd. It is the second time that China hosts such a symposium. By the end of 2011, the China electrical power system had a total of 1 050 GW installed power, out of which 220 GW was in hydropower plants. The energy produced in hydropower facilities was 662.6 TWh from a total of 4,720 TWh electrical energy production in 2011. Moreover, in 2020, new hydropower capacities are going to be developed, with a total of 180 GW installed power and an estimated 708 TWh/year energy production. And in 2011, the installed power of pumped storage stations was about 25GW. In 2020, the data will be 70GW. At the same time, the number of pumps used in China is increasing rapidly. China produces about 29,000,000 pumps with more than 220 series per year. By the end of 2011, the Chinese pumping system has a total of 950 GW installed power. The energy consumed in pumping facilities was 530 TWh in 2011. The pump energy consumption accounted for about 12% of the national electrical energy production. Therefore, there is a large market in the field of hydraulic machinery including water turbines, pump turbines and a variety of pumps in China. There are also many research projects in this field. For example, we have conducted National Key Research Projects on 1000 MW hydraulic turbine, and on the pump turbines with high head, as well as on the large capacity pumps for water supply. Tsinghua University of Beijing is proud to host the 26th IAHR Symposium on Hydraulic Machinery and Systems. Tsinghua University was established in 1911, after the founding of the People's Republic of China. It

Fault size classification of rotating machinery using support vector machine

Energy Technology Data Exchange (ETDEWEB)

Kim, Y. S.; Lee, D. H.; Park, S. K. [Korea Hydro and Nuclear Power Co. Ltd., Daejeon (Korea, Republic of)

2012-03-15

Studies on fault diagnosis of rotating machinery have been carried out to obtain a machinery condition in two ways. First is a classical approach based on signal processing and analysis using vibration and acoustic signals. Second is to use artificial intelligence techniques to classify machinery conditions into normal or one of the pre-determined fault conditions. Support Vector Machine (SVM) is well known as intelligent classifier with robust generalization ability. In this study, a two-step approach is proposed to predict fault types and fault sizes of rotating machinery in nuclear power plants using multi-class SVM technique. The model firstly classifies normal and 12 fault types and then identifies their sizes in case of predicting any faults. The time and frequency domain features are extracted from the measured vibration signals and used as input to SVM. A test rig is used to simulate normal and the well-know 12 artificial fault conditions with three to six fault sizes of rotating machinery. The application results to the test data show that the present method can estimate fault types as well as fault sizes with high accuracy for bearing an shaft-related faults and misalignment. Further research, however, is required to identify fault size in case of unbalance, rubbing, looseness, and coupling-related faults.

Fault size classification of rotating machinery using support vector machine

International Nuclear Information System (INIS)

Kim, Y. S.; Lee, D. H.; Park, S. K.

2012-01-01

Studies on fault diagnosis of rotating machinery have been carried out to obtain a machinery condition in two ways. First is a classical approach based on signal processing and analysis using vibration and acoustic signals. Second is to use artificial intelligence techniques to classify machinery conditions into normal or one of the pre-determined fault conditions. Support Vector Machine (SVM) is well known as intelligent classifier with robust generalization ability. In this study, a two-step approach is proposed to predict fault types and fault sizes of rotating machinery in nuclear power plants using multi-class SVM technique. The model firstly classifies normal and 12 fault types and then identifies their sizes in case of predicting any faults. The time and frequency domain features are extracted from the measured vibration signals and used as input to SVM. A test rig is used to simulate normal and the well-know 12 artificial fault conditions with three to six fault sizes of rotating machinery. The application results to the test data show that the present method can estimate fault types as well as fault sizes with high accuracy for bearing an shaft-related faults and misalignment. Further research, however, is required to identify fault size in case of unbalance, rubbing, looseness, and coupling-related faults

Oil use of the effluent plant ETEO (Effluent Station of Oil Treatment) as combustible for generation of energy in the power plant UG-50Hz; Utulizacao de oleo da ETEO (Estacao de Tratamento de Efluentes Oleosos) para geracao de energia na UG-50Hz

Energy Technology Data Exchange (ETDEWEB)

Souza, Jose Francisco de; Nascimento, Jose Maria do; Silva, Luiz Antonio da; Salazar, Marcos Vinicios; Baptista, Reinaldo Lopes; Barros, Sueli Aguiar [Companhia Siderurgica Nacional (CSN), Volta Redonda, RJ (Brazil)

2009-11-01

The areas of finishing products of CSN Steel Plant generate contaminated effluents with oil and grease , that are treated in ETEO (Effluent Station of Oil Treatment). In this plant, the oil is processed to be sold for the consuming market. However, some seasons of the year, the market does not absorb the oil, and CSN is obliged to defray the burning of this oil, to not interrupt the productive process and cause an environmental impact. Because of this situation, we search alternatives for the viable use of this oil inside CSN steel plant, taking care for the security of the processes and the impact to the environment. This paper describes the details of the work and the implantation of the burning of this oil of the ETEO with BPF oil (type of petrochemical oil) as combustible in the boiler 7 of the power plant UG 50 Hz. For the implantation of this project, operational contingencies of security for equipment was prepared . Moreover, the work included chemical analyses of the oil and the conditions of the boiler using this mixing of oils. The reached results demonstrate the total viability of this project and it was proved another alternative of the use of this residue, with reduction of the fuel costs , steam costs and the electric energy generated in the power plant of CSN. (author)

Grease Cowboy Fever; or, the making of Johnny T.

Science.gov (United States)

Bradford, K

2002-01-01

Through a mix of theory, memoir and performance narrative, this chapter examines the making of drag persona Johnny T. as part of a king movement where the dominant cultural paradigm of gender is reconsidered and remastered. As seen in Grease, Saturday Night Fever and Urban Cowboy, pop culture icon John Travolta's particular blend of 50s greaser, faggy 70s disco, and 80s country masculinities are shown to be prime drag king conditions, particularly for a dyke who came of age during the 70s Travolta fever. While drawing from personal experience as a king, current trends in the king movement, and gender theory, this essay calls into question the lines between performing masculinity on and off the stage, inviting us to see both the work and play, the parody and realness, the struggle and liberation that make up the transgressive world of drag kinging and gender variance. Drawing upon gender theorists Judith Butler and Judith Halberstam, gender is exposed as a social construction both produced and performed, and as such, drag kinging is framed as an arena where gender is reconfigured.

The Autophagic Machinery in Enterovirus Infection.

Science.gov (United States)

Lai, Jeffrey K F; Sam, I-Ching; Chan, Yoke Fun

2016-01-27

The Enterovirus genus of the Picornaviridae family comprises many important human pathogens, including polioviruses, rhinovirus, enterovirus A71, and enterovirus D68. They cause a wide variety of diseases, ranging from mild to severe life-threatening diseases. Currently, no effective vaccine is available against enteroviruses except for poliovirus. Enteroviruses subvert the autophagic machinery to benefit their assembly, maturation, and exit from host. Some enteroviruses spread between cells via a process described as autophagosome-mediated exit without lysis (AWOL). The early and late phases of autophagy are regulated through various lipids and their metabolizing enzymes. Some of these lipids and enzymes are specifically regulated by enteroviruses. In the present review, we summarize the current understanding of the regulation of autophagic machinery by enteroviruses, and provide updates on recent developments in this field.

A Survey of Fish Production and Processing Machinery in Rivers ...

African Journals Online (AJOL)

Survey of fish production and processing machinery in Port Harcourt City Local Government Area of Rivers State, Nigeria was carried out to evaluate the followings: different machines used for fish production and processing, the most acceptable machine, effect of cost of machinery on the fish farmer, whether gender has ...

Study Of The Physicochemical Analysis Of Biodiesel Produced From Waste Vegetable Oil.

Directory of Open Access Journals (Sweden)

C. O. Okpanachi

2017-07-01

Full Text Available The study of the physicochemical analysis of biodiesel produced from waste vegetable oil in Sedi Minna Nigeria was carried out in order to ascertain the quality of the biodiesel produced as regards physical and chemical parameters which include visual appearance colour cloud point flash point and cetane index diesel index kinematic velocity calorific value. Biodiesel is a renewable resource that can replace petroleum diesel which comes from fossil fuels that are limited and will be exhausted in the near future. Biodiesel can be made from the transesterification of vegetable oils animal fat greases and oil crops such as soybean and it is biodegradable. The biodiesel produced was subjected to physicochemical analysis and results of cetane index was established to be 52 the flash point using pensky martens close cup was determine to be 1600C diesel index using IP21 0.3411 kinematic viscosity at 400C to be 4.12 and calorific value of 10867calg. The investigated physicochemical parameters show that the biodiesel produced is suitable for use in diesel engines without modifications and is cheaper to produce compared to petroleum diesel.

Improving biogas production from anaerobic co-digestion of Thickened Waste Activated Sludge (TWAS) and fat, oil and grease (FOG) using a dual-stage hyper-thermophilic/thermophilic semi-continuous reactor.

Science.gov (United States)

Alqaralleh, Rania Mona; Kennedy, Kevin; Delatolla, Robert

2018-07-01

This paper investigates the feasibility and advantages of using a dual-stage hyper-thermophilic/thermophilic semi-continuous reactor system for the co-digestion of Thickened Waste Activated Sludge (TWAS) and Fat, Oil and Grease (FOG) to produce biogas in high quantity and quality. The performance of the dual-stage hyper-thermophilic (70°C)/thermophilic (55°C) anaerobic co-digestion system is evaluated and compared to the performance of a single-stage thermophilic (55°C) reactor that was used to co-digest the same FOG-TWAS mixtures. Both co-digestion reactors were compared to a control reactor (the control reactor was a single-stage thermophilic reactor that only digested TWAS). The effect of FOG% in the co-digestion mixture (based on total volatile solids) and the reactor hydraulic retention time (HRT) on the biogas/methane production and the reactors' performance were thoroughly investigated. The FOG% that led to the maximum methane yield with a stable reactor performance was determined for both reactors. The maximum FOG% obtained for the single-stage thermophilic reactor at 15 days HRT was found to be 65%. This 65% FOG resulted in 88.3% higher methane yield compared to the control reactor. However, the dual-stage hyper-thermophilic/thermophilic co-digestion reactor proved to be more efficient than the single-stage thermophilic co-digestion reactor, as it was able to digest up to 70% FOG with a stable reactor performance. The 70% FOG in the co-digestion mixture resulted in 148.2% higher methane yield compared to the control at 15 days HRT. 70% FOG (based on total volatile solids) is so far the highest FOG% that has been proved to be useful and safe for semi-continuous reactor application in the open literature. Finally, the dual-stage hyper-thermophilic/thermophilic co-digestion reactor also proved to be efficient and stable in co-digesting 40% FOG mixtures at lower HRTs (i.e., 9 and 12 days) and still produce high methane yields and Class A effluents

Detection of Early Faults in Rotating Machinery Based on Wavelet Analysis

Directory of Open Access Journals (Sweden)

Meng Hee Lim

2013-01-01

Full Text Available This paper explores the application of wavelet analysis for the detection of early changes in rotor dynamics caused by common machinery faults, namely, rotor unbalance and minor blade rubbing conditions. In this paper, the time synchronised wavelet analysis method was formulated and its effectiveness to detect machinery faults at the early stage was evaluated based on signal simulation and experimental study. The proposed method provides a more standardised approach to visualise the current state of rotor dynamics of a rotating machinery by taking into account the effects of time shift, wavelet edge distortion, and system noise suppression. The experimental results showed that this method is able to reveal subtle changes of the vibration signal characteristics in both the frequency content distribution and the amplitude distortion caused by minor rotor unbalance and blade rubbing conditions. Besides, this method also appeared to be an effective tool to diagnose and to discriminate the different types of machinery faults based on the unique pattern of the wavelet contours. This study shows that the proposed wavelet analysis method is promising to reveal machinery faults at early stage as compared to vibration spectrum analysis.

Petroleum.

Science.gov (United States)

McManus, T. R.; And Others

1989-01-01

This review of petroleum covers: crude oil; fuels, gaseous and liquid; lubricants, oils, and greases; asphalts, bitumens, tars, and pitches; hydrocarbons; physical properties; metals in oil; nonmetallic elements and heterocompounds; and analytical methods and apparatus. (MVL)

The capacity of sugar beet farms’ machinery and equipment

Directory of Open Access Journals (Sweden)

Małgorzata BZOWSKA – BAKALARZ

2012-12-01

Full Text Available The survey investigates into equipment of sugar beet farms of the Lublin region, Poland, with machinery – with reference to plantation size and yields. To assess the production potential of the farms, the authors determined the age structure of the machinery owned by the farmers and established the scale of investment in new equipment. The machinery most important for sugar beet production are pre-sowing and post-harvest tillage units, sprayers, seed drills, combine harvesters and self-unloading trailers. In most cases, the surveyed farmers own most of these machines, but they are often obsolete: 37% of them is in operation for more than 15 years. As for the machines dedicated solely to sugar beet growing (harvesters and seeders, their age structure is most unfavourable – 70% of them have been used for over 15 years. A trend towards increasing plantation sizes provides incentives for introducing innovation to cultivation methods. However, the scale of investment in new machinery is small, especially in the case of small and medium-sized farms that dominate in the region. The authors surveyed also the scale of using professional services in the field of tillage processes to determine changes in farming practices.

Multiscale singular value manifold for rotating machinery fault diagnosis

Energy Technology Data Exchange (ETDEWEB)

Feng, Yi; Lu, BaoChun; Zhang, Deng Feng [School of Mechanical Engineering, Nanjing University of Science and Technology,Nanjing (United States)

2017-01-15

Time-frequency distribution of vibration signal can be considered as an image that contains more information than signal in time domain. Manifold learning is a novel theory for image recognition that can be also applied to rotating machinery fault pattern recognition based on time-frequency distributions. However, the vibration signal of rotating machinery in fault condition contains cyclical transient impulses with different phrases which are detrimental to image recognition for time-frequency distribution. To eliminate the effects of phase differences and extract the inherent features of time-frequency distributions, a multiscale singular value manifold method is proposed. The obtained low-dimensional multiscale singular value manifold features can reveal the differences of different fault patterns and they are applicable to classification and diagnosis. Experimental verification proves that the performance of the proposed method is superior in rotating machinery fault diagnosis.

STUDY OF THE PARAMETERS OF EFFICIENCY IN CENTRES FOR REPAIR OF AGRICULTURAL MACHINERY

Directory of Open Access Journals (Sweden)

Natalia Stoyanova

2015-06-01

Full Text Available The paper makes a thorough study of the parameters of efficiency in the centers for the repair of agricultural machinery, considering production and technological structure, the basic principles for design of the process of service, the quantitative indicators for servicing. It presents a theoretical model for the management of services in the service business, taking into account the basic system requirements for maintenance of agricultural machinery, the main elements of the standards of customer service, choice of forms for maintenance of agricultural machinery. Opportunities are proposed for the optimization of repair activities in the centers for repair of agricultural machinery.

Synthesis of Green Diesel From Waste Cooking Oil Through Hydrodeoxygenation Technology With NiMo/γ-Al2O3 Catalysts

Directory of Open Access Journals (Sweden)

Heriyanto Heri

2018-01-01

Full Text Available Hydrodeoxygenation (HDO of waste cooking oil (WCO and trapped grease over sulfide catalysts was examined to produce high quality transportation fuel from low-grade resources. The hydrodeoxygenation of waste cooking oils was carried out in a high pressure of 30 and 60 bar and high temperature of 300 – 400 °C in a batch reactor autoclave. NiMo/γ-Al2O3 catalyst was prepared and for the first time tested in hydroprocessing of waste cooking oil. The content of NiMo/γ-Al2O3 in each catalyst was about wCo 5 wt.%. A maximum of 77,97 % green diesel yield was achieved at nearly complete conversion of waste cooking oil using NiMo/γ-Al2O3 at temperature of 400°C, pressure 60 bar and 4 hours of reaction time. The oxygen content was decreased from 14,25 wt.% to 13,35 wt.%, at temperature of 400°C, pressure of 30 bar and 1 hour of reaction time. The Hydrodeoxygenation process was much influenced by temperature, pressure, and time.

Recovery of mineral oil from waste emulsion using electrocoagulation method

Directory of Open Access Journals (Sweden)

Razali Mohd Najib

2016-01-01

Full Text Available This paper presents a research to recover mineral oil from industrial waste emulsion. This research also evaluates the standard of water produced after the oil recovery. The ecosystem could be polluted if this waste is not treated prior to discharge. The equipment needed for this experiment is power supply (generator, connecting wire and metal plate for providing the coagulant. The chosen plates were aluminium and iron plate. The power supply will be connected to the plate producing anode (positive terminal and cathode (negative terminal. Both plates are immersed into a beaker containing waste emulsion. The charge supplied by the current will cause the aluminium or ferum to dissisipate and became ions. These ions will attract the oil to flock together and float at the surface. The water will then filter by using filter paper. Electrocoagulation was done without addition of chemical thus can prevent the hazard from the chemicals. The samples was sent for oil and grease test. The optimum time needed for recovery of oil was 3 hours. The percentage recovery reach constant trend of 95% afterwards. When the power consumption increases, the percentage recovery also increases. However, the current should be lower than 0.5 ampere as it is the limit that human body can withstand. Thus, power consumption of 27.5 Watt was chosen as optimum value. The oil recovery of at power consumption at 27.5W is 96%. The best plate in the process was the aluminium pair which can recover more than ferum plate. The present work concludes the promising future for waste water treatment by usage of electrocoagulation technique.

Condition Monitoring of Machinery in Non-Stationary Operations : Proceedings of the Second International Conference "Condition Monitoring of Machinery in Non-Stationnary Operations"

CERN Document Server

Bartelmus, Walter; Chaari, Fakher; Zimroz, Radoslaw; Haddar, Mohamed

2012-01-01

Condition monitoring of machines in non-stationary operations (CMMNO) can be seen as the major challenge for research in the field of machinery diagnostics. Condition monitoring of machines in non-stationary operations is the title of the presented book and the title of the Conference held in Hammamet - Tunisia March 26 – 28, 2012. It is the second conference under this title, first took place in Wroclaw - Poland , March 2011. The subject CMMNO comes directly from industry needs and observation of real objects. Most monitored and diagnosed objects used in industry works in non-stationary operations condition. The non-stationary operations come from fulfillment of machinery tasks, for which they are designed for. All machinery used in different kind of mines, transport systems, vehicles like: cars, buses etc, helicopters, ships and battleships and so on work in non-stationary operations. The papers included in the book are shaped by the organizing board of the conference and authors of the papers. The papers...

Design and Realization of Rotating Machinery Conditions Monitoring System Based on Labview

Science.gov (United States)

Fan, Qiyuan

Nonlinear dynamic analysis of rotating machinery system has always been the hot spot of the rotational dynamics research. This article sets up a rotating machinery condition monitoring system to realize the measurement of system dynamic characteristic parameters based on NI(National Instruments) virtual instruments technology. The measurement of vibration signal of rotating machinery system is achieved by using NI company general data acquisition module of NI company. Meanwhile, by analyzing and processing the acquired data using Labview 2012, the dynamic characteristics, such as .the speed of the rotating machinery system, the axis trajectory, spectrum parameters, are attained. The measurement results show that the rotating machinery condition monitoring system based on Labview is easy to operate, easy to realize the function extension and maintenance, and that it can be used in the industrial engineering projects with rotation characteristics. Labview as the development tools used by virtual instrument function, is very powerful data acquisition software products support is one of the features of it, so using Labview programming and data acquisition is simple and convenient [1].

Emergence and modular evolution of a novel motility machinery in bacteria.

Directory of Open Access Journals (Sweden)

Jennifer Luciano

2011-09-01

Full Text Available Bacteria glide across solid surfaces by mechanisms that have remained largely mysterious despite decades of research. In the deltaproteobacterium Myxococcus xanthus, this locomotion allows the formation stress-resistant fruiting bodies where sporulation takes place. However, despite the large number of genes identified as important for gliding, no specific machinery has been identified so far, hampering in-depth investigations. Based on the premise that components of the gliding machinery must have co-evolved and encode both envelope-spanning proteins and a molecular motor, we re-annotated known gliding motility genes and examined their taxonomic distribution, genomic localization, and phylogeny. We successfully delineated three functionally related genetic clusters, which we proved experimentally carry genes encoding the basal gliding machinery in M. xanthus, using genetic and localization techniques. For the first time, this study identifies structural gliding motility genes in the Myxobacteria and opens new perspectives to study the motility mechanism. Furthermore, phylogenomics provide insight into how this machinery emerged from an ancestral conserved core of genes of unknown function that evolved to gliding by the recruitment of functional modules in Myxococcales. Surprisingly, this motility machinery appears to be highly related to a sporulation system, underscoring unsuspected common mechanisms in these apparently distinct morphogenic phenomena.

46 CFR 169.631 - Separation of machinery and fuel tank spaces from accommodation spaces.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Separation of machinery and fuel tank spaces from accommodation spaces. 169.631 Section 169.631 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... machinery and fuel tank spaces from accommodation spaces. (a) Machinery and fuel tank spaces must be...

Application of DNA Machineries for the Barcode Patterned Detection of Genes or Proteins.

Science.gov (United States)

Zhou, Zhixin; Luo, Guofeng; Wulf, Verena; Willner, Itamar

2018-06-05

The study introduces an analytical platform for the detection of genes or aptamer-ligand complexes by nucleic acid barcode patterns generated by DNA machineries. The DNA machineries consist of nucleic acid scaffolds that include specific recognition sites for the different genes or aptamer-ligand analytes. The binding of the analytes to the scaffolds initiate, in the presence of the nucleotide mixture, a cyclic polymerization/nicking machinery that yields displaced strands of variable lengths. The electrophoretic separation of the resulting strands provides barcode patterns for the specific detection of the different analytes. Mixtures of DNA machineries that yield, upon sensing of different genes (or aptamer ligands), one-, two-, or three-band barcode patterns are described. The combination of nucleic acid scaffolds acting, in the presence of polymerase/nicking enzyme and nucleotide mixture, as DNA machineries, that generate multiband barcode patterns provide an analytical platform for the detection of an individual gene out of many possible genes. The diversity of genes (or other analytes) that can be analyzed by the DNA machineries and the barcode patterned imaging is given by the Pascal's triangle. As a proof-of-concept, the detection of one of six genes, that is, TP53, Werner syndrome, Tay-Sachs normal gene, BRCA1, Tay-Sachs mutant gene, and cystic fibrosis disorder gene by six two-band barcode patterns is demonstrated. The advantages and limitations of the detection of analytes by polymerase/nicking DNA machineries that yield barcode patterns as imaging readout signals are discussed.

46 CFR 177.620 - Ventilation of machinery and fuel tank spaces.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Ventilation of machinery and fuel tank spaces. 177.620... fuel tank spaces. In addition to the requirements of this subpart, ventilation systems for spaces containing machinery or fuel tanks must comply with the requirements of part 182 of this chapter. ...

The indigenisation of Lubriplate 630-2 and development of Servo-Nuclease-2 grease for the fuelling machine of pressurised heavy water power reactors

International Nuclear Information System (INIS)

Srivastava, S.B.; Thomas, V.G.

1980-01-01

A new grease of NLGI-2 consistency was developed for application in nuclear environments. The evaluation consisted of both static tests employing a cobalt-60 γ-ray source and dynamic tests carried out on specially designed rigs in Fuelling Machine Vaults of RAPS. (auth.)

Structural design of nuclear reactor machinery and equipment

International Nuclear Information System (INIS)

Hara, Hideki

1992-01-01

Since the machinery, equipment and piping which compose nuclear power station facilities are diverse, when those are designed, consideration is given sufficiently to the objective of use and the importance of the object machinery and equipment so that those can maintain the soundness over the design life. In this report, on the contents and the design standard in the design techniques for nuclear reactor machinery and equipment, the way of thinking is shown, taking an example of reactor pressure vessel which is stipulated as the vessel kind 1 in the 'Technical standard of structures and others regarding nuclear facilities for electric power generation', Notice No. 501 of the Ministry of International Trade and Industry. The reactor pressure vessel of 1350 MWe improved type BWR (ABWR) is used under the condition of 87.9 kg/cm 2 and 302 degC, and the inside diameter is about 7.2 m, the inside height is about 21 m, and the wall thickness is about 170 mm. The design standard for reactor pressure vessels and its way of thinking, breakdown prevention design and the design techniques for reactor pressure vessels are described. (K.I.)

Targeting Cell Polarity Machinery to Exhaust Breast Cancer Stem Cells

Science.gov (United States)

2017-10-01

AWARD NUMBER: W81XWH-15-1-0644 TITLE: Targeting Cell Polarity Machinery to Exhaust Breast Cancer Stem Cells PRINCIPAL INVESTIGATOR: Chun-Ju...Targeting Cell Polarity Machinery to Exhaust Breast Cancer Stem Cells 5a. CONTRACT NUMBER 5b. GRANT NUMBER W81XWH-15-1-0644 5c. PROGRAM ELEMENT...Unlimited 13. SUPPLEMENTARY NOTES 14. ABSTRACT Cancer stem cells (CSCs), a cell population with acquired perpetuating self-renewal properties which

Fault Diagnosis for Rotating Machinery: A Method based on Image Processing.

Directory of Open Access Journals (Sweden)

Chen Lu

Full Text Available Rotating machinery is one of the most typical types of mechanical equipment and plays a significant role in industrial applications. Condition monitoring and fault diagnosis of rotating machinery has gained wide attention for its significance in preventing catastrophic accident and guaranteeing sufficient maintenance. With the development of science and technology, fault diagnosis methods based on multi-disciplines are becoming the focus in the field of fault diagnosis of rotating machinery. This paper presents a multi-discipline method based on image-processing for fault diagnosis of rotating machinery. Different from traditional analysis method in one-dimensional space, this study employs computing method in the field of image processing to realize automatic feature extraction and fault diagnosis in a two-dimensional space. The proposed method mainly includes the following steps. First, the vibration signal is transformed into a bi-spectrum contour map utilizing bi-spectrum technology, which provides a basis for the following image-based feature extraction. Then, an emerging approach in the field of image processing for feature extraction, speeded-up robust features, is employed to automatically exact fault features from the transformed bi-spectrum contour map and finally form a high-dimensional feature vector. To reduce the dimensionality of the feature vector, thus highlighting main fault features and reducing subsequent computing resources, t-Distributed Stochastic Neighbor Embedding is adopt to reduce the dimensionality of the feature vector. At last, probabilistic neural network is introduced for fault identification. Two typical rotating machinery, axial piston hydraulic pump and self-priming centrifugal pumps, are selected to demonstrate the effectiveness of the proposed method. Results show that the proposed method based on image-processing achieves a high accuracy, thus providing a highly effective means to fault diagnosis for

Fault Diagnosis for Rotating Machinery: A Method based on Image Processing.

Science.gov (United States)

Lu, Chen; Wang, Yang; Ragulskis, Minvydas; Cheng, Yujie

2016-01-01

Rotating machinery is one of the most typical types of mechanical equipment and plays a significant role in industrial applications. Condition monitoring and fault diagnosis of rotating machinery has gained wide attention for its significance in preventing catastrophic accident and guaranteeing sufficient maintenance. With the development of science and technology, fault diagnosis methods based on multi-disciplines are becoming the focus in the field of fault diagnosis of rotating machinery. This paper presents a multi-discipline method based on image-processing for fault diagnosis of rotating machinery. Different from traditional analysis method in one-dimensional space, this study employs computing method in the field of image processing to realize automatic feature extraction and fault diagnosis in a two-dimensional space. The proposed method mainly includes the following steps. First, the vibration signal is transformed into a bi-spectrum contour map utilizing bi-spectrum technology, which provides a basis for the following image-based feature extraction. Then, an emerging approach in the field of image processing for feature extraction, speeded-up robust features, is employed to automatically exact fault features from the transformed bi-spectrum contour map and finally form a high-dimensional feature vector. To reduce the dimensionality of the feature vector, thus highlighting main fault features and reducing subsequent computing resources, t-Distributed Stochastic Neighbor Embedding is adopt to reduce the dimensionality of the feature vector. At last, probabilistic neural network is introduced for fault identification. Two typical rotating machinery, axial piston hydraulic pump and self-priming centrifugal pumps, are selected to demonstrate the effectiveness of the proposed method. Results show that the proposed method based on image-processing achieves a high accuracy, thus providing a highly effective means to fault diagnosis for rotating machinery.

Modern principles used in conformity assessment of machinery from forestry sector

Directory of Open Access Journals (Sweden)

Antonov Anca Elena

2017-01-01

Full Text Available The paper is aiming to implement the general principles of risk prevention at employer’s level, with respect to occupational risks evaluation, the elimination of risk and accident factors, and information of workers which are using the machinery in the forestry sector. For the use of machinery in the forestry sector in terms of economic performance and a level of maximum safety, it is necessary to ensure the user guides set by the manufacturer in terms of commissioning, use and to provide appropriate safe working operations and interventions and to guarantee the technical and environmental requirements, including appropriate measures and means of protection against accidents and occupational disease. The impact of occupational risks for machinery used in this sector can be reduced through the application of modern principles in conformity assessment and certification and, where appropriate, through technical diagnostics and inspection, taking into account the provisions of the new Machinery Directive 2006/42 / EC which is imposing the obligation of manufacturer to implement conformity assessment procedures in accordance with the methods of assessment and verification of safety at the certification bodies, notified at the European Commission. The paper aims to develop modern technical tools for conformity assessment and verification of this category of machines used in the forestry sector that would provide prerequisite for increasing competitiveness of employers in the market economy. Applying these tools of modern technology for manufacturers and users of this category of machinery provides the necessary conditions for placing on the market of safe products with a appropriate safety level, in the intended using conditions, in order to guarantee the essential requirements for safety and health, technical and environmental conditions, including measures and means of protection. The result of this research is to develop technical tools needed to

Sand or grease? Corruption-institutional trust nexus in post-Soviet countries

Directory of Open Access Journals (Sweden)

Nazim Habibov

2017-07-01

Full Text Available This paper empirically tests several hypotheses about the nexus of corruption-institutional trust in Post-Soviet transitional countries of the former Soviet Union and Mongolia. We use two different indices of institutional trust to check the robustness of our analysis and estimate OLS and instrumental variable models with and without interaction terms. All things considered, our findings reject “greases the wheels” and “trust begets an honest political system” hypotheses. Instead, our findings support the “sand the wheels” hypothesis. Furthermore, a multiplicative interaction model suggests that the negative marginal effects of experienced corruption are higher in the environments where satisfaction with services is low. In addition, we found that increases in corruption erode trust at all levels of the societal institutions including political parties, government and financial institutions, international investors, non-profit organizations, and trade unions. This finding is important since it highlights the negative consequences of corruption on the development of broader level economic institutions and on civil society.

The accident analysis of mobile mine machinery in Indian opencast coal mines.

Science.gov (United States)

Kumar, R; Ghosh, A K

2014-01-01

This paper presents the analysis of large mining machinery related accidents in Indian opencast coal mines. The trends of coal production, share of mining methods in production, machinery deployment in open cast mines, size and population of machinery, accidents due to machinery, types and causes of accidents have been analysed from the year 1995 to 2008. The scrutiny of accidents during this period reveals that most of the responsible factors are machine reversal, haul road design, human fault, operator's fault, machine fault, visibility and dump design. Considering the types of machines, namely, dumpers, excavators, dozers and loaders together the maximum number of fatal accidents has been caused by operator's faults and human faults jointly during the period from 1995 to 2008. The novel finding of this analysis is that large machines with state-of-the-art safety system did not reduce the fatal accidents in Indian opencast coal mines.

Densification of chipper harvested SRC using on-farm machinery

Energy Technology Data Exchange (ETDEWEB)

Paulson, M.

2003-07-01

This report gives details of a project to density wood chips using on-farm machinery in order to avoid problems encountered in bulk handling and storage of low density short rotation cultivation (SRC) wood chips - especially as some customers can only accept baled material. Trials using different lengths of chips produced by a standard SRC harvester are described, and the failure to produce acceptable bales is reported. The potential cost of modifying equipment is deemed to make the baling of SRC chips using standard farm machinery currently not viable.

49 CFR 393.130 - What are the rules for securing heavy vehicles, equipment and machinery?

Science.gov (United States)

2010-10-01

... heavy vehicles, equipment and machinery? (a) Applicability. The rules in this section apply to the transportation of heavy vehicles, equipment and machinery which operate on wheels or tracks, such as front end... heavy vehicles, equipment or machinery with crawler tracks or wheels. (1) In addition to the...

Intelligence and the machinery of government: conceptualizing the intelligence community

OpenAIRE

Davies, PHJ

2010-01-01

This article argues that the failure to address intelligence agencies as public organizations part and parcel with the overt machinery of government constitutes a significant lacuna both in the specialist study of intelligence and the broader discipline of public administration studies. The role and status of intelligence institutions as aspects of the machinery of central government is examined, along with the prospects of certain key paradigms in the field for understanding those institutio...

Knowledge Transfer between Service and Design Phases in the Oil Industry

DEFF Research Database (Denmark)

Vianello, Giovanna; Ahmed, Saeema

2009-01-01

Communication between departments in any company involved in the different phases of product lifecycle is crucial in order to correct faults from previous products. This paper illustrates a case study from the oil industry where knowledge transfer across departments is analysed. Interviews...... with engineering designers and service engineers were carried out. Knowledge arising from the operation of drilling machineries was investigated and compared to that relevant for the engineering designers; furthermore the mechanisms involved in the transfer of knowledge between service and design were investigated....... Differences in knowledge needs were observed in the two departments: engineering designers were more orientated towards knowledge of machinery at a component level while service engineers were interested in obtaining an overview of the systems. The study showed that communication between the departments...

FOREWORD: The XXV IAHR Symposium on Hydraulic Machinery and Systems marks half a century tradition

Science.gov (United States)

Susan-Resiga, Romeo

2010-05-01

results in rising global temperatures and dramatic changes in climate which may also result in flooding in parts of our globe. Energy conservation together with replacement of coal and oil-fired power plants are, therefore, needed. The development and installation of more efficient hydroelectric power plants which work hand in hand with water storage and flood protection is part of this strategy. Waterpower is the most significant 'renewable resource'. The goals of this IAHR - Committee on Hydraulic Machinery and Systems are to improve the value of hydraulic machinery to the end user and to society and to improve society's understanding and appreciation of that value. The series of IAHR Symposia on Hydraulic Machinery and Cavitation started with the 1st edition in Nice in 1960 in France. Within the past decade, all the symposia were focused on an extended portfolio of topics under the name of 'Hydraulic Machinery and Systems', such as the 20th edition in 2000, Charlotte, USA, the 21st in 2002, Lausanne, Switzerland, the 22nd in 2004, Stockholm, Sweden, the 23rd in 2006, Yokohama, Japan, and the 24th in 2008, Foz do Iguassu, Brasil. The 25th IAHR Symposium on Hydraulic Machinery and Systems brings together more than 150 scientists and researchers from 24 countries, affiliated with universities , technology centres and industry to debate topics related to advanced technologies for hydraulic machinery and systems, which will enhance the sustainable development of water resources and hydropower production. The Scientific Committee has selected 118 papers, out of 238 abstracts submitted, on the following topics: (i) Hydraulic Turbines and Pumps, (ii) Sustainable hydropower, (iii) Hydraulic Systems, (iv) Advances in Computational and Experimental Techniques, (v) Innovative Technology, to be presented at the symposium and to be included in the proceedings. All papers published in this Volume 12 of IOP Conference Series: Earth and Environmental Science have been peer reviewed

Vibration Feature Extraction and Analysis for Fault Diagnosis of Rotating Machinery-A Literature Survey

OpenAIRE

Saleem Riaz; Hassan Elahi; Kashif Javaid; Tufail Shahzad

2017-01-01

Safety, reliability, efficiency and performance of rotating machinery in all industrial applications are the main concerns. Rotating machines are widely used in various industrial applications. Condition monitoring and fault diagnosis of rotating machinery faults are very important and often complex and labor-intensive. Feature extraction techniques play a vital role for a reliable, effective and efficient feature extraction for the diagnosis of rotating machinery. Therefore, deve...

Transfer of Service Knowledge: A case from the oil industry

DEFF Research Database (Denmark)

Ahmed, Saeema; Vianello, Giovanna

2009-01-01

The general trend in engineering design is to consider issues related to the product lifecycle during the design of a product. Hence, the capture of knowledge arising during the operation phase (service) and the feedback of this to engineering designers is an important aspect of complex products....... A case study of drilling machinery for offshore oil rigs has been selected. This choice arose from the unique characteristics of this industry where solutions are specific for each rig, so re-design or adaptation of machineries and assembly is required in each project and it’s imperative to have...... a correct set of requirements and design. As the drilling machines are one-off machines, the transfer of experience between projects and knowledge from operational experience is essential. Interviews with the project team from the company owning the rig (drilling contractor), and the service engineers from...

High voltage electrification of tractor and agricultural machinery – A review

International Nuclear Information System (INIS)

Moreda, G.P.; Muñoz-García, M.A.; Barreiro, P.

2016-01-01

Highlights: • CO_2 emission reduction calls for energy-efficient mobile work machines. • Energy recovery could be possible in some agricultural machinery operations. • Owning and operating costs of electrified tractor-implement pairs should be analyzed. • Plug-in hybrid electric tractors running along tramlines make sense. • Electrification allows for precise speed control, noise reduction and flexible design. - Abstract: Reduction of both pollutant emissions and fossil fuel dependency is an objective of energy policies worldwide. In many countries, governments promote the use of efficient vehicles like the hybrid electric vehicle. Incorporation of electric drives in tractor and agricultural machinery presents advantages in terms of increased energy efficiency and expanded functionalities. Higher efficiency means reduction in fuel consumption and subsequent decrease in CO_2 emission. New functionalities improve work quality and increase operator comfort. Tractor electrification takes advantage of decoupling loads and drives from the engine, which allows operating the latter at its highest efficiency point. Major advantages of machinery electrification are torque and speed control, noise reduction, and a more flexible design. In this paper, a review of the state-of-the-art of agricultural machinery high voltage electrification is presented.

Market brief : the oil and gas market in Bolivia

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-03-01

This report presents a market overview of the oil and gas sector in Bolivia and describes the potential for Canadian suppliers to enter into joint ventures to establish local production facilities and transfer technology expertise. Bolivia has an estimated 54.9 trillion cubic feet of natural gas reserves and 440.5 million barrels of proven oil reserves. The main hope for future economic growth in Bolivia hinges on increasing natural gas exports. Opportunities for Canadian companies exist in exploration, production and pipeline construction. There is also a demand for drilling machinery equipment, pipeline components and services for the expansion of the proposed Bolivia-Brazil pipeline. The largest energy company in Bolivia is Repsol YPF which operates through its subsidiary Empress Petrolera Andina. The largest end-users of oil and gas equipment and services include domestic upstream operators and international oil majors and international exploration and production companies. This report describes the key factors shaping market growth along with the competitive environment, local capabilities, international competition and the Canadian position. Considerations for market-entry in Bolivia were also outlined.

CCPIT Machinery Exhibition Succeeded in Kuala Lumpur

Institute of Scientific and Technical Information of China (English)

无

2005-01-01

@@ From August 18 to 20, 2005, China Council for the Promotion of International Trade(CCPIT) held China Machinery and Electronics Trade Exhibition, CME 2005 in Kuala Lumpur, the capital of Malaysia on behalf of China, a good job has been done.

Structural insights into the bacterial carbon - phosphorus lyase machinery

DEFF Research Database (Denmark)

Seweryn, Paulina; Van, Lan Bich; Kjeldgaard, Morten

2015-01-01

Phosphorus is required for all life and microorganisms can extract it from their environment through several metabolic pathways. When phosphate is in limited supply, some bacteria are able to use phosphonate compounds, which require specialized enzymatic machinery to break the stable carbon......–phosphorus (C–P) bond. Despite its importance, the details of how this machinery catabolizes phosphonates remain unknown. Here we determine the crystal structure of the 240-kilodalton Escherichia coli C–P lyase core complex (PhnG–PhnH–PhnI–PhnJ; PhnGHIJ), and show that it is a two-fold symmetric hetero...

Classifying machinery condition using oil samples and binary logistic regression

Science.gov (United States)

Phillips, J.; Cripps, E.; Lau, John W.; Hodkiewicz, M. R.

2015-08-01

The era of big data has resulted in an explosion of condition monitoring information. The result is an increasing motivation to automate the costly and time consuming human elements involved in the classification of machine health. When working with industry it is important to build an understanding and hence some trust in the classification scheme for those who use the analysis to initiate maintenance tasks. Typically "black box" approaches such as artificial neural networks (ANN) and support vector machines (SVM) can be difficult to provide ease of interpretability. In contrast, this paper argues that logistic regression offers easy interpretability to industry experts, providing insight to the drivers of the human classification process and to the ramifications of potential misclassification. Of course, accuracy is of foremost importance in any automated classification scheme, so we also provide a comparative study based on predictive performance of logistic regression, ANN and SVM. A real world oil analysis data set from engines on mining trucks is presented and using cross-validation we demonstrate that logistic regression out-performs the ANN and SVM approaches in terms of prediction for healthy/not healthy engines.

46 CFR 167.65-60 - Examination of boilers and machinery by engineer.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Examination of boilers and machinery by engineer. 167.65-60 Section 167.65-60 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL... machinery by engineer. It shall be the duty of an engineer when he assumes charge of the boilers and...

The oil and gas equipment and services market in India

International Nuclear Information System (INIS)

2002-01-01

In terms of purchasing power, India represents the fourth largest economy in the world. In the year April 1, 2001-Mar 31, 2002, it was estimated that India had a 5.4 per cent growth in gross domestic product (GDP). Canada experienced a 19.9 per cent increase in exports to India in 2001, reaching 656 million dollars. With the world's six-largest energy consumption, oil demand in India is expected to grow to 179 million tonnes in 2006-2007, while the demand for natural gas is expected to reach 231 million cubic metres per day in the same period. To meet this growing demand, India will require investments in the order of 150 billion dollars over the next 10 to 12 years. The oil and gas industry is being opened to the private sector and foreign direct investment, due to new government policies on exploration, production, distribution, and sales. Foreign involvement in exploration, previously restricted to Indian state-owned firms, is now allowed through the New Exploration Licensing Policy. In exploration and production (E and P) activities, as well as the refinery sector, foreign ownership of up to 100 per cent is now allowed. Two Indian companies which dominate the Indian E and P sector, namely Oil and Natural Gas Corporation (ONGC) and Oil India Limited (OIL), will be upgrading their ageing infrastructure, purchasing new equipment and redeveloping existing oil and gas fields, thereby creating opportunities for the supply of equipment and services. Canadian companies possessing the latest technologies and services in exploration, drilling machinery and equipment, directional drilling services, production machinery and equipment, enhanced recovery services, deep-water drilling equipment and services, and equipment for coal methane E and P should benefit from these opportunities. Over 12,000 kilometres of pipelines are being planned across India, as well as private opportunities in the refinery sector which was opened to the private sector in April 2002. Occasional

Development of a new separator oil/water: adaptation of a laboratory prototype envisage an industrial application; Desenvolvimento de um novo separador oleo/agua: adaptacao do prototipo de laboratorio visando aplicacao industrial

Energy Technology Data Exchange (ETDEWEB)

Medeiros, Gustavo de S.; Paulo, Joao B. de A.; Costa Junior, Jose A. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil); Fernandes Junior, Wilaci E. [PETROBRAS, Natal/Fortaleza, RN/CE (Brazil). Unidade RN/CE

2008-07-01

The present work deals with the adaptation of a new separator oil/water called Mixer Settler based on Phase Inversion of (MDIF) in scale of laboratory for future application in industrial scale. The adaptations were carried out by changing of the materials of construction and the substitution of the original system of mechanical mixing by a static or on-line mixer. The equipment works through the unit operation of liquid-liquid extraction associated with the innovative method of phase inversion to separate the fine oil droplets which appear emulsified into produced waters. The extractant solvent was QAV (aviation kerosene). A composed central design was used to evaluate the performance of the equipment, considering the separation efficiency (%) as the response variable in function of the TOG (total oil and greases). Envisaging an industrial application we plotted contour curves to determine the regions which it is possible to operate the equipment on optimized conditions in view of separate oil at low concentrations, minimizing the quantity of extractant solvent. (author)

Thermo-mechanical properties of carbon nanotubes and applications in thermal management

Science.gov (United States)

Nguyen, Manh Hong; Thang Bui, Hung; Trinh Pham, Van; Phan, Ngoc Hong; Nguyen, Tuan Hong; Chuc Nguyen, Van; Quang Le, Dinh; Khoi Phan, Hong; Phan, Ngoc Minh

2016-06-01

Thanks to their very high thermal conductivity, high Young’s modulus and unique tensile strength, carbon nanotubes (CNTs) have become one of the most suitable nano additives for heat conductive materials. In this work, we present results obtained for the synthesis of heat conductive materials containing CNT based thermal greases, nanoliquids and lubricating oils. These synthesized heat conductive materials were applied to thermal management for high power electronic devices (CPUs, LEDs) and internal combustion engines. The simulation and experimental results on thermal greases for an Intel Pentium IV processor showed that the thermal conductivity of greases increases 1.4 times and the saturation temperature of the CPU decreased by 5 °C by using thermal grease containing 2 wt% CNTs. Nanoliquids containing CNT based distilled water/ethylene glycol were successfully applied in heat dissipation for an Intel Core i5 processor and a 450 W floodlight LED. The experimental results showed that the saturation temperature of the Intel Core i5 processor and the 450 W floodlight LED decreased by about 6 °C and 3.5 °C, respectively, when using nanoliquids containing 1 g l-1 of CNTs. The CNTs were also effectively utilized additive materials for the synthesis of lubricating oils to improve the thermal conductivity, heat dissipation efficiency and performance efficiency of engines. The experimental results show that the thermal conductivity of lubricating oils increased by 12.5%, the engine saved 15% fuel consumption, and the longevity of the lubricating oil increased up to 20 000 km by using 0.1% vol. CNTs in the lubricating oils. All above results have confirmed the tremendous application potential of heat conductive materials containing CNTs in thermal management for high power electronic devices, internal combustion engines and other high power apparatus.

CCPIT Machinery Exhibition Succeeded in Kuala Lumpur

Institute of Scientific and Technical Information of China (English)

无

2005-01-01

　　From August 18 to 20, 2005, China Council for the Promotion of International Trade(CCPIT) held China Machinery and Electronics Trade Exhibition, CME 2005 in Kuala Lumpur, the capital of Malaysia on behalf of China, a good job has been done.……

Web-based Interactive Simulator for Rotating Machinery.

Science.gov (United States)

Sirohi, Vijayalaxmi

1999-01-01

Baroma (Balance of Rotating Machinery), the Web-based educational engineering interactive software for teaching/learning combines didactical and software ergonomical approaches. The software in tutorial form simulates a problem using Visual Interactive Simulation in graphic display, and animation is brought about through graphical user interface…

Directional Wigner-Ville distribution and its application for rotating-machinery condition monitoring

International Nuclear Information System (INIS)

Kim, Dong Wan; Ha, Jae HOng; Shin, Hae Gon; Lee, Yoon Hee; Kim, Young Baik

1996-01-01

Vibration analysis is one of the most powerful tools available for the detection and isolation of incipient faults in mechanical systems. The methods of vibration analysis in use today and under continuous study are broad band vibration monitoring, time domain analysis, and frequency domain analysis. In recent years, great interest has been generated concerning the use of time-frequency representation and its application for a machinery diagnostics and condition monitoring system. The objective of the research described in this paper was to develop a new diagnostic tool for the rotating machinery. This paper introduces a new time-frequency representation, Directional Wigner-Ville Distribution, which analyses the time-frequency structure of the rotating machinery vibration

ERGONOMIC AND ECOLOGICALSAFETY - FACTORSNESSARY TO IMPROVETHE COMPETITIVENESS OF THE DOMESTIC CONSTRUCTION MACHINERY

Directory of Open Access Journals (Sweden)

Volkov Andrey Anatol’evich

2017-03-01

Full Text Available The analysis of output and domestic used construction machinery showed that the most vulnerable link remains a problem of underreporting of ergonomics and environmental safety requirements. Compliance with ergonomic requirements enhances the performance of mechanized operations, leading to a decrease in construction costs. Increased environmental requirements reduce the negative impact on air basin. These results suggest the need to improve the structures of building machines. Made recommendations for a comprehensive solution to the problem. The measures to improve environmental safety, ergonomic design requirements of construction machinery, mechanisms of the optimal development of the domestic construction machinery, through the development and implementation of appropriate measures. Keywords: ergonomics of construction equipment, environmental safety of construction equipment

46 CFR 111.103-1 - Power ventilation systems except machinery space ventilation systems.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Power ventilation systems except machinery space ventilation systems. 111.103-1 Section 111.103-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY... Power ventilation systems except machinery space ventilation systems. Each power ventilation system must...

Digestibility of energy and lipids and oxidative stress in nursery pigs fed commercially available lipids

Science.gov (United States)

An experiment was conducted to evaluate the impact of lipid source on GE and ether extract (EE) digestibility, oxidative stress, and gut integrity in nursery pigs fed diets containing 10% of soybean oil (SO), choice white grease (CWG), palm oil (PO), or 2 different distillers corn oils (DCO-1 and DC...

A Method of Rotating Machinery Fault Diagnosis Based on the Close Degree of Information Entropy

Institute of Scientific and Technical Information of China (English)

GENG Jun-bao; HUANG Shu-hong; JIN Jia-shan; CHEN Fei; LIU Wei

2006-01-01

This paper presents a method of rotating machinery fault diagnosis based on the close degree of information entropy. In the view of the information entropy, we introduce four information entropy features of the rotating machinery, which describe the vibration condition of the machinery. The four features are, respectively, denominated as singular spectrum entropy, power spectrum entropy, wavelet space state feature entropy and wavelet power spectrum entropy. The value scopes of the four information entropy features of the rotating machinery in some typical fault conditions are gained by experiments, which can be acted as the standard features of fault diagnosis. According to the principle of the shorter distance between the more similar models, the decision-making method based on the close degree of information entropy is put forward to deal with the recognition of fault patterns. We demonstrate the effectiveness of this approach in an instance involving the fault pattern recognition of some rotating machinery.

Environmental contaminants in oil field produced waters discharged into wetlands

International Nuclear Information System (INIS)

Ramirez, P. Jr.

1994-01-01

The 866-acre Loch Katrine wetland complex in Park County, Wyoming provides habitat for many species of aquatic birds. The complex is sustained primarily by oil field produced waters. This study was designed to determine if constituents in oil field produced waters discharged into Custer Lake and to Loch Katrine pose a risk to aquatic birds inhabiting the wetlands. Trace elements, hydrocarbons and radium-226 concentrations were analyzed in water, sediment and biota collected from the complex during 1992. Arsenic, boron, radium-226 and zinc were elevated in some matrices. The presence of radium-226 in aquatic vegetation suggests that this radionuclide is available to aquatic birds. Oil and grease concentrations in water from the produced water discharge exceeded the maximum 10 mg/l permitted by the WDEQ (1990). Total aliphatic and aromatic hydrocarbon concentrations in sediments were highest at the produced water discharge, 6.376 μg/g, followed by Custer Lake, 1.104 μg/g. The higher levels of hydrocarbons found at Custer Lake, compared to Loch Katrine, may be explained by Custer Lake's closer proximity to the discharge. Benzo(a)pyrene was not detected in bile from gadwalls collected at Loch Katrine but was detected in bile from northern shovelers collected at Custer Lake. Benzo(a)pyrene concentrations in northern shoveler bile ranged from 500 to 960 ng/g (ppb) wet weight. The presence of benzo(a)pyrene in the shovelers indicates exposure to petroleum hydrocarbons

The ongoing changes in the base oil industry and their potential impact on the lubricant industry

Energy Technology Data Exchange (ETDEWEB)

Serra-Holm, Valentina [Nynas AB, Stockholm (Sweden)

2013-06-15

During the last years the base oil industry has undergone significant changes, with the rapid growth of Group II and Group III paraffinic base oils and the corresponding decline of Group I supply. The announcements of future instalments show that the increase of Group II and III capacity is indeed a stable trend all over the world. Based on publicly available information, the Group II capacity is expected to grow by 8.6 million tpa, reaching over 22 million tpa, and Group III capacity is expected to double from current 4.1 million tpa up to 8.2 million tpa. As the demand is not expected to grow at the same pace as the increasing supply, it is likely that this new capacity will lead to an oversupply situation in the next five years. Because of their production disadvantages compared to Group II and III and a shrinking demand in automotive applications, it is likely that Group I plants will close down or will operate at reduced throughput to compensate for the new Group II and III capacity. A decline of Group I capacity in favour of Group II and III may pose problems in the formulation of those industrial lubricants where solvency and/or viscosity are needed, such as lubricating greases, metalworking fluids, and several process oils applications. Either alone or in combination with Group II or III oils, naphthenic oils can be used in the formulation of industrial lubricants, as solvency and viscosity poroviders. (orig.)

Fault Diagnosis for Rotating Machinery Using Vibration Measurement Deep Statistical Feature Learning

Directory of Open Access Journals (Sweden)

Chuan Li

2016-06-01

Full Text Available Fault diagnosis is important for the maintenance of rotating machinery. The detection of faults and fault patterns is a challenging part of machinery fault diagnosis. To tackle this problem, a model for deep statistical feature learning from vibration measurements of rotating machinery is presented in this paper. Vibration sensor signals collected from rotating mechanical systems are represented in the time, frequency, and time-frequency domains, each of which is then used to produce a statistical feature set. For learning statistical features, real-value Gaussian-Bernoulli restricted Boltzmann machines (GRBMs are stacked to develop a Gaussian-Bernoulli deep Boltzmann machine (GDBM. The suggested approach is applied as a deep statistical feature learning tool for both gearbox and bearing systems. The fault classification performances in experiments using this approach are 95.17% for the gearbox, and 91.75% for the bearing system. The proposed approach is compared to such standard methods as a support vector machine, GRBM and a combination model. In experiments, the best fault classification rate was detected using the proposed model. The results show that deep learning with statistical feature extraction has an essential improvement potential for diagnosing rotating machinery faults.

Fault Diagnosis for Rotating Machinery Using Vibration Measurement Deep Statistical Feature Learning.

Science.gov (United States)

Li, Chuan; Sánchez, René-Vinicio; Zurita, Grover; Cerrada, Mariela; Cabrera, Diego

2016-06-17

Fault diagnosis is important for the maintenance of rotating machinery. The detection of faults and fault patterns is a challenging part of machinery fault diagnosis. To tackle this problem, a model for deep statistical feature learning from vibration measurements of rotating machinery is presented in this paper. Vibration sensor signals collected from rotating mechanical systems are represented in the time, frequency, and time-frequency domains, each of which is then used to produce a statistical feature set. For learning statistical features, real-value Gaussian-Bernoulli restricted Boltzmann machines (GRBMs) are stacked to develop a Gaussian-Bernoulli deep Boltzmann machine (GDBM). The suggested approach is applied as a deep statistical feature learning tool for both gearbox and bearing systems. The fault classification performances in experiments using this approach are 95.17% for the gearbox, and 91.75% for the bearing system. The proposed approach is compared to such standard methods as a support vector machine, GRBM and a combination model. In experiments, the best fault classification rate was detected using the proposed model. The results show that deep learning with statistical feature extraction has an essential improvement potential for diagnosing rotating machinery faults.

Performance of machinery in potato production in one growing season

Directory of Open Access Journals (Sweden)

Kun Zhou

2015-12-01

Full Text Available Statistics on the machinery performance are essential for farm managers to make better decisions. In this paper, the performance of all machineries in five sequential operations, namely bed forming, stone separation, planting, spraying and harvesting in the potato production system, were investigated during one growing season. In order to analyse and decompose the recorded GPS data into various time and distance elements for estimation of the machinery performance, an automatic GPS analysis tool was developed. The field efficiency and field capacity were estimated for each operation. Specifically, the measured average field efficiency was 71.3% for bed forming, 68.5% for stone separation, 40.3% for planting, 69.7% for spraying, and 67.4% for harvesting. The measured average field capacities were 1.46 ha/h, 0.53 ha/h, 0.47 ha/h, 10.21 ha/h, 0.51 ha/h, for the bed forming, stone separation, planting, spraying, and harvesting operations, respectively. These results deviate from the corresponding estimations calculated based on norm data from the American Society of Agricultural and Biological Engineers (ASABE. The deviations indicate that norms provided by ASABE cannot be used directly for the prediction of performance of the machinery used in this work. Moreover, the measured data of bed forming and stone separation could be used as supplementary data for the ASABE which does not provide performance norms for these two operations. The gained results can help farm managers to make better management and operational decisions that result in potential improvement in productivity and profitability as well as in potential environmental benefits.

Performance of machinery in potato production in one growing season

Energy Technology Data Exchange (ETDEWEB)

Zhou, K.; Jensen, A.L.; Bochtis, D.D.; Sørensen, C.G.

2015-07-01

Statistics on the machinery performance are essential for farm managers to make better decisions. In this paper, the performance of all machineries in five sequential operations, namely bed forming, stone separation, planting, spraying and harvesting in the potato production system, were investigated during one growing season. In order to analyse and decompose the recorded GPS data into various time and distance elements for estimation of the machinery performance, an automatic GPS analysis tool was developed. The field efficiency and field capacity were estimated for each operation. Specifically, the measured average field efficiency was 71.3% for bed forming, 68.5% for stone separation, 40.3% for planting, 69.7% for spraying, and 67.4% for harvesting. The measured average field capacities were 1.46 ha/h, 0.53 ha/h, 0.47 ha/h, 10.21 ha/h, 0.51 ha/h, for the bed forming, stone separation, planting, spraying, and harvesting operations, respectively. These results deviate from the corresponding estimations calculated based on norm data from the American Society of Agricultural and Biological Engineers (ASABE). The deviations indicate that norms provided by ASABE cannot be used directly for the prediction of performance of the machinery used in this work. Moreover, the measured data of bed forming and stone separation could be used as supplementary data for the ASABE which does not provide performance norms for these two operations. The gained results can help farm managers to make better management and operational decisions that result in potential improvement in productivity and profitability as well as in potential environmental benefits. (Author)

Machinery and labour force requirements for forest chip production in Finland in 2020

Energy Technology Data Exchange (ETDEWEB)

Kaerhae, K.; Strandsroem, M. (Metsaeteho Oy, Helsinki (Finland)), Email: kalle.karha@metsateho.fi, Email: markus.strandstrom@metsateho.fi; Lahtinen, P.; Elo, J. (Poeyry Energy Oy, Espoo (Finland)), Email: perttu.lahtinen@poyry.com, Email: juha.elo@poyry.com

2009-07-01

The research carried out by Metsaeteho Oy and Poeyry Energy Oy estimated how much machinery and labour would be needed for large-scale forest chip production if the use of forest chips increases extensively in Finland during the coming decade. If the production and consumption of forest chips are 25 to 30 TWh in Finland 2020, then 1,900 to 2,200 machinery units, i.e. machines and trucks, would be needed. This would mean total investments in production machinery of 530 to 630 million euro (VAT 0 %). The labour demand would be 3,400 to 4,000 machine operators and drivers, and 4,200 to 5,100 labour years including indirect labour. Respectively, if the production and consumption of forest chips is 15 to 20 TWh in Finland in 2020, then the production machinery requirement would be 1,100 to 1,500 machines and trucks. The total machinery investment cost would be 320 to 420 million euro (VAT 0 %) and the calculated labour demand 2,000 to 2,700 machine operators and drivers (2,500 to 3,400 labour years). The results of the study indicated that forest chip production resources will be a major bottleneck in reaching the consumption target of 12 million m3, i.e. around 24 TWh of forest chips in Finland by 2020. (orig.)

Spatiotemporal Regulation of Nuclear Transport Machinery and Microtubule Organization

Science.gov (United States)

Okada, Naoyuki; Sato, Masamitsu

2015-01-01

Spindle microtubules capture and segregate chromosomes and, therefore, their assembly is an essential event in mitosis. To carry out their mission, many key players for microtubule formation need to be strictly orchestrated. Particularly, proteins that assemble the spindle need to be translocated at appropriate sites during mitosis. A small GTPase (hydrolase enzyme of guanosine triphosphate), Ran, controls this translocation. Ran plays many roles in many cellular events: nucleocytoplasmic shuttling through the nuclear envelope, assembly of the mitotic spindle, and reorganization of the nuclear envelope at the mitotic exit. Although these events are seemingly distinct, recent studies demonstrate that the mechanisms underlying these phenomena are substantially the same as explained by molecular interplay of the master regulator Ran, the transport factor importin, and its cargo proteins. Our review focuses on how the transport machinery regulates mitotic progression of cells. We summarize translocation mechanisms governed by Ran and its regulatory proteins, and particularly focus on Ran-GTP targets in fission yeast that promote spindle formation. We also discuss the coordination of the spatial and temporal regulation of proteins from the viewpoint of transport machinery. We propose that the transport machinery is an essential key that couples the spatial and temporal events in cells. PMID:26308057

THE IMPACT OF THE ELEVATOR GUIDES CONTAMINATION ON THE BRAKING PROCESS DELAY FOR SELECTED PROGRESSIVE GEARS

Directory of Open Access Journals (Sweden)

Rafał Longwic

2017-06-01

Full Text Available The authors’ tests results on the impact of the guiding system (the guides contamination in the friction lift on the delay of progressive gears braking process are presented in this article. The tests were conducted using a free fall method and a test bench built for that purpose. In order to render all working conditions the guiding system of tested gears was lubricated with the most commonly used lubricating agents. Solid grease (SM, mineral oil (OL, the mixture of solid grease and quartz sand (S50 as well as the mixture of mineral oil and quartz sand (O50 were used.

The use of supercritical carbon dioxide for contaminant removal from solid waste

International Nuclear Information System (INIS)

Adkins, C.L.J.; Russick, E.M.; Smith, H.M.; Olson, R.B.

1994-01-01

Supercritical carbon dioxide is being explored as a waste minimization technique for separating oils, greases and solvents from solid waste. The containments are dissolved into the supercritical fluid and precipitated out upon depressurization. The carbon dioxide solvent can then be recycled for continued use. Definitions of the temperature, pressure, flowrate and potential co-solvents are required to establish the optimum conditions for hazardous contaminant removal. Excellent extractive capability for common manufacturing oils, greases, and solvents has been observed in both supercritical and liquid carbon dioxide. Solubility measurements are being used to better understand the extraction process, and to determine if the minimum solubility required by federal regulations is met

Research on bearing fault diagnosis of large machinery based on mathematical morphology

Science.gov (United States)

Wang, Yu

2018-04-01

To study the automatic diagnosis of large machinery fault based on support vector machine, combining the four common faults of the large machinery, the support vector machine is used to classify and identify the fault. The extracted feature vectors are entered. The feature vector is trained and identified by multi - classification method. The optimal parameters of the support vector machine are searched by trial and error method and cross validation method. Then, the support vector machine is compared with BP neural network. The results show that the support vector machines are short in time and high in classification accuracy. It is more suitable for the research of fault diagnosis in large machinery. Therefore, it can be concluded that the training speed of support vector machines (SVM) is fast and the performance is good.

Application of Choi—Williams Reduced Interference Time Frequency Distribution to Machinery Diagnostics

Directory of Open Access Journals (Sweden)

Howard A. Gaberson

1995-01-01

Full Text Available This article discusses time frequency analysis of machinery diagnostic vibration signals. The short time Fourier transform, the Wigner, and the Choi–Williams distributions are explained and illustrated with test cases. Examples of Choi—Williams analyses of machinery vibration signals are presented. The analyses detect discontinuities in the signals and their timing, amplitude and frequency modulation, and the presence of different components in a vibration signal.

An Association of Unique microRNA Turnover Machinery with Prostate Cancer Progression

Science.gov (United States)

2017-10-01

targeting of critical androgen receptor -604 coregulator interactions in prostate cancer . Nature communications 4, 1923, 605 doi:10.1038/ncomms2912 (2013...AWARD NUMBER: W81XWH-16-1-0474 TITLE: An Association of Unique microRNA Turnover Machinery with Prostate Cancer Progression PRINCIPAL INVESTIGATOR...14 Sep 2017 4. Title An Association of Unique microRNA Turnover Machinery with Prostate Cancer Progression 5a. CONTRACT NUMBER 5b. GRANT NUMBER

Molecular building blocks and their architecture in biologically/environmentally compatible soft matter chemical machinery.

Science.gov (United States)

Toyota, Taro; Banno, Taisuke; Nitta, Sachiko; Takinoue, Masahiro; Nomoto, Tomonori; Natsume, Yuno; Matsumura, Shuichi; Fujinami, Masanori

2014-01-01

This review briefly summarizes recent developments in the construction of biologically/environmentally compatible chemical machinery composed of soft matter. Since environmental and living systems are open systems, chemical machinery must continuously fulfill its functions not only through the influx and generation of molecules but also via the degradation and dissipation of molecules. If the degradation or dissipation of soft matter molecular building blocks and biomaterial molecules/polymers can be achieved, soft matter particles composed of them can be used to realize chemical machinery such as selfpropelled droplets, drug delivery carriers, tissue regeneration scaffolds, protocell models, cell-/tissuemarkers, and molecular computing systems.

The RNAi Inheritance Machinery of Caenorhabditis elegans.

Science.gov (United States)

Spracklin, George; Fields, Brandon; Wan, Gang; Becker, Diveena; Wallig, Ashley; Shukla, Aditi; Kennedy, Scott

2017-07-01

Gene silencing mediated by dsRNA (RNAi) can persist for multiple generations in Caenorhabditis elegans (termed RNAi inheritance). Here we describe the results of a forward genetic screen in C. elegans that has identified six factors required for RNAi inheritance: GLH-1/VASA, PUP-1/CDE-1, MORC-1, SET-32, and two novel nematode-specific factors that we term here (heritable RNAi defective) HRDE-2 and HRDE-4 The new RNAi inheritance factors exhibit mortal germline (Mrt) phenotypes, which we show is likely caused by epigenetic deregulation in germ cells. We also show that HRDE-2 contributes to RNAi inheritance by facilitating the binding of small RNAs to the inheritance Argonaute (Ago) HRDE-1 Together, our results identify additional components of the RNAi inheritance machinery whose conservation provides insights into the molecular mechanism of RNAi inheritance, further our understanding of how the RNAi inheritance machinery promotes germline immortality, and show that HRDE-2 couples the inheritance Ago HRDE-1 with the small RNAs it needs to direct RNAi inheritance and germline immortality. Copyright © 2017 by the Genetics Society of America.

Machinery health prognostics: A systematic review from data acquisition to RUL prediction

Science.gov (United States)

Lei, Yaguo; Li, Naipeng; Guo, Liang; Li, Ningbo; Yan, Tao; Lin, Jing

2018-05-01

Machinery prognostics is one of the major tasks in condition based maintenance (CBM), which aims to predict the remaining useful life (RUL) of machinery based on condition information. A machinery prognostic program generally consists of four technical processes, i.e., data acquisition, health indicator (HI) construction, health stage (HS) division, and RUL prediction. Over recent years, a significant amount of research work has been undertaken in each of the four processes. And much literature has made an excellent overview on the last process, i.e., RUL prediction. However, there has not been a systematic review that covers the four technical processes comprehensively. To fill this gap, this paper provides a review on machinery prognostics following its whole program, i.e., from data acquisition to RUL prediction. First, in data acquisition, several prognostic datasets widely used in academic literature are introduced systematically. Then, commonly used HI construction approaches and metrics are discussed. After that, the HS division process is summarized by introducing its major tasks and existing approaches. Afterwards, the advancements of RUL prediction are reviewed including the popular approaches and metrics. Finally, the paper provides discussions on current situation, upcoming challenges as well as possible future trends for researchers in this field.

Availability analysis of selected mining machinery

Directory of Open Access Journals (Sweden)

Brodny Jarosław

2017-06-01

Full Text Available Underground extraction of coal is characterized by high variability of mining and geological conditions in which it is conducted. Despite ever more effective methods and tools, used to identify the factors influencing this process, mining machinery, used in mining underground, work in difficult and not always foreseeable conditions, which means that these machines should be very universal and reliable. Additionally, a big competition, occurring on the coal market, causes that it is necessary to take action in order to reduce the cost of its production, e.g. by increasing the efficiency of utilization machines. To meet this objective it should be pro-ceed with analysis presented in this paper. The analysis concerns to availability of utilization selected mining machinery, conducted using the model of OEE, which is a tool for quantitative estimate strategy TPM. In this article we considered the machines being part of the mechanized longwall complex and the basis of analysis was the data recording by the industrial automation system. Using this data set we evaluated the availability of studied machines and the structure of registered breaks in their work. The results should be an important source of information for maintenance staff and management of mining plants, needed to improve the economic efficiency of underground mining.

Comparison of Management-Operational Efficiency of Agricultural Machinery Operating Systems (Case Study Alborz Province

Directory of Open Access Journals (Sweden)

A Omidi

2017-10-01

Full Text Available Introduction Measuring the efficiency of operating systems in comparison with the methods of comparing the performance of systems explains the various dimensions of issues such as, the lack of full use of agricultural machinery capacity, improper selection of machine, incorrect use of machinery, ownership, etc.. Any improvement in operating system conditions reduces costs,, consumption of inputs, increases the efficiency of production factors and consequently reduces the price and increases agricultural profitability. The main objective of this research is to compare the operational-management efficiency of operating systems in Alborz province and comparison of managerial and operational efficiency of agricultural machinery farming systems by calculating the efficiency of its major components in agricultural machinery farming systems including efficiency, social, economic, technical-operational and managerial and ranking them in order to understand the optimal model of agricultural machinery systems. Materials and Methods This research is a survey study.The study population was beneficiaries of agricultural machinery in the Alborz province which in the multi-stage random sample was determined. Alborz province has 31,438 agricultural operations, of which 543 are exploited agricultural machinery. Cochran formula was used to determine sample size. Since, Cronbach's alpha coefficient greater than 0.7 was obtained by questionnaire, the reliability of the questionnaires was assessed as desirable. To calculate the efficiency the component data were extracted from 4 specialized questionnaires after the initial examination and encoding, then they were analyzed using the software SPSS, MCDM Engine. TOPSIS techniques were used for ranking managerial performance operating system for operating agricultural machinery Alborz province. Results and Discussion The results showed that social efficiency of dedicated-professional operation with an average of 6.6 had

[Effects of heavy machinery operation on the structural characters of cultivated soils in black soil region of Northeast China].

Science.gov (United States)

Wang, En-Heng; Chai, Ya-Fan; Chen, Xiang-Wei

2008-02-01

With the cultivated soils in black soil region of Northeast China as test objects, this paper measured their structural characters such as soil strength, bulk density, and non-capillary porosity/capillary porosity (NCP/CP) ratio before and after heavy and medium-sized machinery operation, aimed to study the effects of machinery operation on the physical properties of test soils. The results showed that after machinery operation, there existed three distinct layers from top to bottom in the soil profiles, i.e., plowed layer, cumulative compacted layer, and non-affected layer, according to the changes of soil strength. Under medium-sized machinery operation, these three layers were shallower, and there was a new plow pan at the depth between 17.5 and 30 cm. Heavy machinery operation had significant positive effects on the improvement of topsoil structure (P heavy machinery, the bulk density of topsoil decreased by 7.2% and 3.5%, respectively, and NCP/CP increased by 556.6% after subsoiling, which would benefit water infiltration, reinforce water storage, and weaken the threat of soil erosion. The main action of heavy machinery operation was soil loosening, while that of medium-sized machinery operation was soil compacting.

On the reversed Brayton cycle with high speed machinery

Energy Technology Data Exchange (ETDEWEB)

Backman, J.

1996-12-31

This work was carried out in the laboratory of Fluid Dynamics, at Lappeenranta University of Technology during the years 1991-1996. The research was a part of larger high speed technology development research. First, there was the idea of making high speed machinery applications with the Brayton cycle. There was a clear need to deepen the knowledge of the cycle itself and to make a new approach in the field of the research. Also, the removal of water from the humid air seemed very interesting. The goal of this work was to study methods of designing high speed machinery for the reversed Brayton cycle, from theoretical principles to practical applications. The reversed Brayton cycle can be employed as an air dryer, a heat pump or a refrigerating machine. In this research the use of humid air as a working fluid has an environmental advantage, as well. A new calculation method for the Brayton cycle is developed. In this method especially the expansion process in the turbine is important because of the condensation of the water vapour in the humid air. This physical phenomena can have significant effects on the level of performance of the application. Also, the influence of calculating the process with actual, achievable process equipment efficiencies is essential for the development of future machinery. The above theoretical calculations are confirmed with two different laboratory prototypes. (53 refs.)

On the reversed Brayton cycle with high speed machinery

Energy Technology Data Exchange (ETDEWEB)

Backman, J

1997-12-31

This work was carried out in the laboratory of Fluid Dynamics, at Lappeenranta University of Technology during the years 1991-1996. The research was a part of larger high speed technology development research. First, there was the idea of making high speed machinery applications with the Brayton cycle. There was a clear need to deepen the knowledge of the cycle itself and to make a new approach in the field of the research. Also, the removal of water from the humid air seemed very interesting. The goal of this work was to study methods of designing high speed machinery for the reversed Brayton cycle, from theoretical principles to practical applications. The reversed Brayton cycle can be employed as an air dryer, a heat pump or a refrigerating machine. In this research the use of humid air as a working fluid has an environmental advantage, as well. A new calculation method for the Brayton cycle is developed. In this method especially the expansion process in the turbine is important because of the condensation of the water vapour in the humid air. This physical phenomena can have significant effects on the level of performance of the application. Also, the influence of calculating the process with actual, achievable process equipment efficiencies is essential for the development of future machinery. The above theoretical calculations are confirmed with two different laboratory prototypes. (53 refs.)

Soybean plant-based toxicity assessment and phytoremediation of soils contaminated by vegetable and mineral oils used in power electrical transformers.

Science.gov (United States)

Sanderson, Karina; Módenes, Aparecido Nivaldo; Espinoza-Quiñones, Fernando Rodolfo; Trigueros, Daniela Estelita Goes; Júnior, Luiz Antônio Zanão; Schuelter, Adilson Ricken; Neves, Camila Vargas; Kroumov, Alexander Dimitrov

2018-04-01

In this work, deleterious effects in soils due to the presence of dielectric fluids were investigated. For this purpose, vegetable (Envirotemp ® FR3) and mineral (Lubrax AV 66 IN) oils were used for simulating a set of soils contaminated in different oil contents (0.5, 1.0, 2.0, 2.5, 5.0, 7.5 and 10%) in which three 120-days soybean crop periods (SCP) were carried out using the species Glycine max (L.) Merr. Both soil and soybean plant samples were analysed on following the changes on chemical attributes, content of oils and greases (COG) in soils and phytotechnical characteristics of soybean plant. No significant changes on soil chemical attributes were found. For a 0.5% vegetable oil fraction, COG removals of 35, 60 and 90% were observed after the 1st, 2nd, and 3rd SCPs, respectively, whereas removals of 25, 40 and 70% were observed for 0.5% mineral oil fraction after the 1st, 2nd, and 3rd SCPs, respectively. There was an effectively accumulated removal on all tested oil fractions as being proportional to the integrated 120-days SCPs, suggesting a lesser number of crops for a complete abatement of oil fraction in soil. A 100% recovery on the seedlings emergence fractions was also evidenced, revealing that at least a number of 7 and 9 SCPs should be applied continuously in soils contaminated by vegetable and mineral oils, respectively, in order to no longer jeopardize soybean plant growth. Finally, an empirical prediction of the number of SCPs necessary for the complete removal of oil from the soil was proposed. Copyright © 2018 Elsevier Ltd. All rights reserved.

A risk-based approach for identifying constituents of concern in oil sands process-affected water from the Athabasca Oil Sands region.

Science.gov (United States)

McQueen, Andrew D; Kinley, Ciera M; Hendrikse, Maas; Gaspari, Daniel P; Calomeni, Alyssa J; Iwinski, Kyla J; Castle, James W; Haakensen, Monique C; Peru, Kerry M; Headley, John V; Rodgers, John H

2017-04-01

Mining leases in the Athabasca Oil Sands (AOS) region produce large volumes of oil sands process-affected water (OSPW) containing constituents that limit beneficial uses and discharge into receiving systems. The aim of this research is to identify constituents of concern (COCs) in OSPW sourced from an active settling basin with the goal of providing a sound rational for developing mitigation strategies for using constructed treatment wetlands for COCs contained in OSPW. COCs were identified through several lines of evidence: 1) chemical and physical characterization of OSPW and comparisons with numeric water quality guidelines and toxicity endpoints, 2) measuring toxicity of OSPW using a taxonomic range of sentinel organisms (i.e. fish, aquatic invertebrates, and a macrophyte), 3) conducting process-based manipulations (PBMs) of OSPW to alter toxicity and inform treatment processes, and 4) discerning potential treatment pathways to mitigate ecological risks of OSPW based on identification of COCs, toxicological analyses, and PBM results. COCs identified in OSPW included organics (naphthenic acids [NAs], oil and grease [O/G]), metals/metalloids, and suspended solids. In terms of species sensitivities to undiluted OSPW, fish ≥ aquatic invertebrates > macrophytes. Bench-scale manipulations of the organic fractions of OSPW via PBMs (i.e. H 2 O 2 +UV 254 and granular activated charcoal treatments) eliminated toxicity to Ceriodaphnia dubia (7-8 d), in terms of mortality and reproduction. Results from this study provide critical information to inform mitigation strategies using passive or semi-passive treatment processes (e.g., constructed treatment wetlands) to mitigate ecological risks of OSPW to aquatic organisms. Copyright © 2017 Elsevier Ltd. All rights reserved.

Machinery fault diagnosis using joint global and local/nonlocal discriminant analysis with selective ensemble learning

Science.gov (United States)

Yu, Jianbo

2016-11-01

The vibration signals of faulty machine are generally non-stationary and nonlinear under those complicated working conditions. Thus, it is a big challenge to extract and select the effective features from vibration signals for machinery fault diagnosis. This paper proposes a new manifold learning algorithm, joint global and local/nonlocal discriminant analysis (GLNDA), which aims to extract effective intrinsic geometrical information from the given vibration data. Comparisons with other regular methods, principal component analysis (PCA), local preserving projection (LPP), linear discriminant analysis (LDA) and local LDA (LLDA), illustrate the superiority of GLNDA in machinery fault diagnosis. Based on the extracted information by GLNDA, a GLNDA-based Fisher discriminant rule (FDR) is put forward and applied to machinery fault diagnosis without additional recognizer construction procedure. By importing Bagging into GLNDA score-based feature selection and FDR, a novel manifold ensemble method (selective GLNDA ensemble, SE-GLNDA) is investigated for machinery fault diagnosis. The motivation for developing ensemble of manifold learning components is that it can achieve higher accuracy and applicability than single component in machinery fault diagnosis. The effectiveness of the SE-GLNDA-based fault diagnosis method has been verified by experimental results from bearing full life testers.

The phototransduction machinery in the rod outer segment has a strong efficacy gradient

KAUST Repository

Mazzolini, Monica

2015-05-04

Rod photoreceptors consist of an outer segment (OS) and an inner segment. Inside the OS a biochemical machinery transforms the rhodopsin photoisomerization into electrical signal. This machinery has been treated as and is thought to be homogenous with marginal inhomogeneities. To verify this assumption, we developed a methodology based on special tapered optical fibers (TOFs) to deliver highly localized light stimulations. By using these TOFs, specific regions of the rod OS could be stimulated with spots of light highly confined in space. As the TOF is moved from the OS base toward its tip, the amplitude of saturating and single photon responses decreases, demonstrating that the efficacy of the transduction machinery is not uniform and is 5-10 times higher at the base than at the tip. This gradient of efficacy of the transduction machinery is attributed to a progressive depletion of the phosphodiesterase along the rod OS. Moreover we demonstrate that, using restricted spots of light, the duration of the photoresponse along the OS does not increase linearly with the light intensity as with diffuse light. © 2015, National Academy of Sciences. All rights reserved.

Non-machinery dialysis that achieves blood purification therapy without using full-scale dialysis machines.

Science.gov (United States)

Abe, Takaya; Onoda, Mistutaka; Matsuura, Tomohiko; Sugimura, Jun; Obara, Wataru; Sato, Toshiya; Takahashi, Mihoko; Chiba, Kenta; Abe, Tomiya

2017-09-01

An electrical or water supply and a blood purification machine are required for renal replacement therapy. There is a possibility that acute kidney injury can occur in large numbers and on a wide scale in the case of a massive earthquake, and there is the potential risk that the current supply will be unable to cope with acute kidney injury cases. However, non-machinery dialysis requires exclusive circuits and has the characteristic of not requiring the full-scale dialysis machines. We performed perfusion experiments that used non-machinery dialysis and recent blood purification machines in 30-min intervals, and the effectiveness of non-machinery dialysis was evaluated by the assessing the removal efficiency of potassium, which causes lethal arrhythmia during acute kidney injury. The non-machinery dialysis potassium removal rate was at the same level as continuous blood purification machines with a dialysate flow rate of 5 L/h after 15 min and continuous blood purification machines with a dialysate flow rate of 3 L/h after 30 min. Non-machinery dialysis required an exclusive dialysate circuit, the frequent need to replace bags, and new dialysate exchanged once every 30 min. However, it can be seen as an effective renal replacement therapy for crush-related acute kidney injury patients, even in locations or facilities not having the full-scale dialysis machines.

Acoustic Camera as a Fool for Identifying Machinery and Equipment Failures

Directory of Open Access Journals (Sweden)

Ľudmila Pavlikova

2018-03-01

Full Text Available Sound and noise are as old as humanity itself. They have accompanied civilization, evolution, and development for centuries. Music and speech represent not only the key elements of human life but also unpleasant feelings of noise that have always been an integral part of human existence. As industrial development has required more energy, powerful machinery, and equipment, there have been still noisier machines. Traffic has grown quickly due to the number and speed of vehicles. For that reason, an acoustic camera is used for the dynamic visualization of machinery and equipment noise as it analyses the sources of noise in details. Subsequently, qualified measures are introduced based on the results of the analysis. The paper considers launching another application. According to the proposed methodology, its use in identifying machinery and equipment failures and their maintenance is proved. The experiment was performed on a four-wheel lawn mower. The primary focus was on the identification of failures using an acoustic camera. The previous method allowed to quickly, precisely and efficiently identifying the failures in two out of five tested machines.

Natural Resource Damage Assessment in highly impacted systems: A case study of the Anacostia River oil spill

International Nuclear Information System (INIS)

Pinkney, A.E.; Frithsen, J.B.; Burton, W.H.; Scott, L.C.; Siciliano, J.

1993-01-01

An approach and case study are presented to assessing natural resource damages due to additional perturbations in highly disturbed systems. The approach involves: (1) defining chemical characteristics unique to the additional perturbation, (2) identifying specific natural resources that may be sensitive to the additional perturbation and the most appropriate sampling period for each, and (3) using existing data to characterize previous conditions. This approach was used to assess the residual effects of a January 1992 spill of 3,400 gallons of number-sign 4 fuel oil in the Anacostia River, Washington, DC. Water quality is poor due to continuing inputs from urban runoff; one upstream tributary (Hickey Run) has a fifty year history of chronic oil spills and stormwater runoff of oil and grease. The challenge was to isolate possible spill impacts from those due to chronic pollutant inputs. GC/FID fingerprinting analyses were used to characterize spill material and hydrocarbons found in the spill area and two adjacent reference areas. Fish larvae (ichthyoplankton) and benthic invertebrates were identified as biological resources most likely to demonstrate residual effects. Results indicated that there were insignificant amounts of the hydrocarbons from the spill in the water, sediments, and biota of the river, and no residual impacts on biological resources could be identified

Safeness of radiological machinery

International Nuclear Information System (INIS)

Yokoyama, Shun

1979-01-01

The human factors affecting the safeness of radiological machinery, which are often very big and complicated machines, are described from the stand point of handling. 20 to 50% of the troubles on equipments seem to be caused by men. This percentage will become even higher in highly developed equipments. Human factors have a great influence on the safeness of radiological equipments. As the human factors, there are sensory factors and knowledge factors as well as psychological factors, and the combination of these factors causes mishandling and danger. Medical services at present are divided in various areas, and consist of the teamwork of the people in various professions. Good human relationship, education and control are highly required to secure the safeness. (Kobatake, H.)

Welding technologies for nuclear machinery and equipment

International Nuclear Information System (INIS)

Kobayashi, Masahiro; Yokono, Tomomi.

1991-01-01

The main welding methods applied to nuclear machinery and equipment are shielded metal arc welding, submerged arc welding, MAG welding and TIG welding. But in the last 10 years, in order to improve the reliability required for the welding of nuclear machinery and equipment, the welding technologies aiming at the reduction of heat input, the decrease of the number of welding pass and the automatic control of welding factors have been applied for the main purpose of bettering the quality and excluding human errors. The merits and the technology of narrow gap, pulsed MAG welding and melt-through welding are explained. As the automation of TIG welding, image processing type narrow gap, hot wire TIG welding and remote control type automatic TIG welding are described. For the longitudinal welding of active metal sheet products, plasma key-hole welding is applied. Since the concentration of its arc is good, high speed welding with low heat input can be done. For the stainless steel cladding by welding, electroslag welding has become to be employed in place of conventional submerged arc welding. Arc is not generated in the electroslag welding, and the penetration into base metal is small. (K.I.)

Rotating Machinery Predictive Maintenance Through Expert System

Directory of Open Access Journals (Sweden)

M. Sarath Kumar

2000-01-01

Full Text Available Modern rotating machines such as turbomachines, either produce or absorb huge amount of power. Some of the common applications are: steam turbine-generator and gas turbine-compressor-generator trains produce power and machines, such as pumps, centrifugal compressors, motors, generators, machine tool spindles, etc., are being used in industrial applications. Condition-based maintenance of rotating machinery is a common practice where the machine's condition is monitored constantly, so that timely maintenance can be done. Since modern machines are complex and the amount of data to be interpreted is huge, we need precise and fast methods in order to arrive at the best recommendations to prevent catastrophic failure and to prolong the life of the equipment. In the present work using vibration characteristics of a rotor-bearing system, the condition of a rotating machinery (electrical rotor is predicted using an off-line expert system. The analysis of the problem is carried out in an Object Oriented Programming (OOP framework using the finite element method. The expert system which is also developed in an OOP paradigm gives the type of the malfunctions, suggestions and recommendations. The system is implemented in C++.

77 FR 59458 - Regulation of Fuels and Fuel Additives: 2013 Biomass-Based Diesel Renewable Fuel Volume

Science.gov (United States)

2012-09-27

... gasoline and diesel fuel or renewable fuels such as ethanol and biodiesel. Potentially regulated categories... of Biodiesel 1. Grease and Rendered Fats 2. Corn Oil 3. Soybean Oil 4. Effects on Food Prices 5.... Deliverability and Transport Costs of Materials, Goods, and Products Other Than Renewable Fuel 6. Wetlands...

Risco de intoxicação profissional por tricloroetileno em processos de desengraxamento no município de São Paulo, Brasil Risk of occupational intoxication due to trichloroethvlene in grease removal operations in the county of S. Paulo, Brazil

Directory of Open Access Journals (Sweden)

Herbert M. A. Stettiner

1977-09-01

Full Text Available A toxicidade de vapores de tricloroetileno (TRI em locais de trabalho é posta em evidência. Determinou-se a concentração de vapores de TRI no ar em fábricas e oficinas onde o líquido serve para desengraxar peças metálicas. Os metabólitos do TRI, o ácido tricloroacético e o tricloroetanol foram determinados em urina de pessoas expostas. Os resultados destas determinações permitem ver a periculosidade potencial que o uso do TRI apresenta.The toxic effects of trichloroethylene (TRI vapors are explained. The TRI vapors have been determined in the air of workingplaces where the liquid is used to remove oil and grease from metal surfaces. Its metabolites, tricehorocetic acid and trichloroethanol have been determined in the urine of exposed persons. The TRI vapors concentrations and urinary TCA resuts confirm the potential danger represented by the use of trichloroethylene in decreasing processes.

46 CFR 35.25-1 - Examination of boilers and machinery by engineer-T/ALL.

Science.gov (United States)

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Examination of boilers and machinery by engineer-T/ALL... Engine Department § 35.25-1 Examination of boilers and machinery by engineer—T/ALL. It shall be the duty of an engineer when assuming charge of the boilers to examine the same forthwith and thoroughly. If...

Trend and current practices of palm oil mill effluent polishing: Application of advanced oxidation processes and their future perspectives.

Science.gov (United States)

Bello, Mustapha Mohammed; Abdul Raman, Abdul Aziz

2017-08-01

Palm oil processing is a multi-stage operation which generates large amount of effluent. On average, palm oil mill effluent (POME) may contain up to 51, 000 mg/L COD, 25,000 mg/L BOD, 40,000 TS and 6000 mg/L oil and grease. Due to its potential to cause environmental pollution, palm oil mills are required to treat the effluent prior to discharge. Biological treatments using open ponding system are widely used for POME treatment. Although these processes are capable of reducing the pollutant concentrations, they require long hydraulic retention time and large space, with the effluent frequently failing to satisfy the discharge regulation. Due to more stringent environmental regulations, research interest has recently shifted to the development of polishing technologies for the biologically-treated POME. Various technologies such as advanced oxidation processes, membrane technology, adsorption and coagulation have been investigated. Among these, advanced oxidation processes have shown potentials as polishing technologies for POME. This paper offers an overview on the POME polishing technologies, with particularly emphasis on advanced oxidation processes and their prospects for large scale applications. Although there are some challenges in large scale applications of these technologies, this review offers some perspectives that could help in overcoming these challenges. Copyright © 2017 Elsevier Ltd. All rights reserved.

Machinery prognostics and prognosis oriented maintenance management

CERN Document Server

Yan, Jihong

2014-01-01

This book gives a complete presentatin of the basic essentials of machinery prognostics and prognosis oriented maintenance management, and takes a look at the cutting-edge discipline of intelligent failure prognosis technologies for condition-based maintenance.  Latest research results and application methods are introduced for signal processing, reliability moelling, deterioration evaluation, residual life prediction and maintenance-optimization as well as applications of these methods.

Optimization Model for Machinery Selection of Multi-Crop Farms in Elsuki Agricultural Scheme

Directory of Open Access Journals (Sweden)

Mysara Ahmed Mohamed

2017-07-01

Full Text Available The optimization machinery model was developed to aid decision-makers and farm machinery managers in determining the optimal number of tractors, scheduling the agricultural operation and minimizing machinery total costs. For purpose of model verification, validation and application input data was collected from primary & secondary sources from Elsuki agricultural scheme for two seasons namely 2011-2012 and 2013-2014. Model verification was made by comparing the numbers of tractors of Elsuki agricultural scheme for season 2011-2012 with those estimated by the model. The model succeeded in reducing the number of tractors and operation total cost by 23%. The effect of optimization model on elements of direct cost saving indicated that the highest cost saving is reached with depreciation, repair and maintenance (23% and the minimum cost saving is attained with fuel cost (22%. Sensitivity analysis in terms of change in model input for each of cultivated area and total costs of operations showing that: Increasing the operation total cost by 10% decreased the total number of tractors after optimization by 23% and total cost of operations was also decreased by 23%. Increasing the cultivated area by 10%, decreased the total number of tractors after optimization by(12% and total cost of operations was also decreased by 12% (16669206 SDG(1111280 $ to 14636376 SDG(975758 $. For the case of multiple input effect of the area and operation total cost resulted in decrease maximum number of tractors by 12%, and the total cost of operations also decreased by 12%. It is recommended to apply the optimization model as pre-requisite for improving machinery management during implementation of machinery scheduling.

Machinery for Forest Chip Production in Finland in 2007 and in the Future

Energy Technology Data Exchange (ETDEWEB)

Kaerhae, Kalle (Metsaeteho Oy, P.O. Box 101, FI-00171 Helsinki (Finland))

2008-10-15

Metsaeteho Oy's study consisted of a survey of the production machinery for forest chips used by energy plants in 2007. The major forest chip suppliers in Finland were involved in the study. In addition, the machinery and equipment stocked by the manufacturers and vendors of energy wood harvester heads, stump lifting devices, and chippers were also surveyed. The study provided also an estimate of future machinery requirements for forest chip production in Finland. The study estimated that a total of 1,100 machine and truck units were employed in the production of forest chips for energy plants in 2007. A total of 770 machine and truck units were contracted for the major forest chip suppliers in 2007. Increasing forest chip consumption will considerable increase the demand for additional forest chip production resources in the future. If the consumption of forest chips by energy plants in 2015 reaches 15 TWh, i.e. about 7.5 mill. m3, then the forest machine and truck requirement will be over 1,700 units. The corresponding machinery requirement at an energy plant with a forest chip consumption of 25 TWh (approx. 12.5 mill. m3), will be close to 2,300 machine and truck units

Non-Dispersive Infrared Sensor for Online Condition Monitoring of Gearbox Oil

Directory of Open Access Journals (Sweden)

Markus S. Rauscher

2017-02-01

Full Text Available The condition of lubricating oil used in automotive and industrial gearboxes must be controlled in order to guarantee optimum performance and prevent damage to machinery parts. In normal practice, this is done by regular oil change intervals and routine laboratory analysis, both of which involve considerable operating costs. In this paper, we present a compact and robust optical sensor that can be installed in the lubrication circuit to provide quasi-continuous information about the condition of the oil. The measuring principle is based on non-dispersive infrared spectroscopy. The implemented sensor setup consists of an optical measurement cell, two thin-film infrared emitters, and two four-channel pyroelectric detectors equipped with optical bandpass filters. We present a method based on multivariate partial least squares regression to select appropriate optical bandpass filters for monitoring the oxidation, water content, and acid number of the oil. We perform a ray tracing analysis to analyze and correct the influence of the light path in the optical setup on the optical parameters of the bandpass filters. The measurement values acquired with the sensor for three different gearbox oil types show high correlation with laboratory reference data for the oxidation, water content, and acid number. The presented sensor can thus be a useful supplementary tool for the online condition monitoring of lubricants when integrated into a gearbox oil circuit.

Physical and Chemical Characterization of Fat and Oil Deposits in Mashhad City Sewer Lines and the Solutions Developed

Directory of Open Access Journals (Sweden)

Mahdi kamali

2017-01-01

Full Text Available Formation of oil, fat, and grease deposits in sewer pipelines is a major concern as they result in sewage overflow and pose health problems. Analysis of two sample deposits collected from the sewer lines of Imam Reza Street in the city of Mashhad suggested that the chemical reactions promoted by edible oils in the sewer lines lead to the formation of insoluble soap and deposits. Being sticky, the deposits accumulate over time to eventually block the lines. The analysis also showed that the moisture content of the samples ranged between 50‒62%, indicating that water does not play a main role in their formation. The samples were also found to contain 61.78% and 84.35% saturated fatty acids, with palmitic acid being the dominant one. Calcium was the main metal in the samples, which is due to both water hardness and corrosion of the sewer lines. Based on the results obtained, the origin of these deposits, and the relevant protocols for the management of oil and fat wastes, solutions were proposed to prevent deposit formation and sewer line clogging that suit the special cultural and environmental conditions of the city. These proposals are under consideration for implementation in the region.

Power electronics and electric machinery challenges and opportunities in electric and hybrid vehicles

Energy Technology Data Exchange (ETDEWEB)

Adams, D.J.; Hsu, J.S.; Young, R.W. [Oak Ridge National Lab., TN (United States); Peng, F.Z. [Univ. of Tennessee, Knoxville, TN (United States)

1997-06-01

The development of power electronics and electric machinery presents significant challenges to the advancement of electric and hybrid vehicles. Electronic components and systems development for vehicle applications have progressed from the replacement of mechanical systems to the availability of features that can only be realized through interacting electronic controls and devices. Near-term applications of power electronics in vehicles will enable integrated powertrain controls, integrated chassis system controls, and navigation and communications systems. Future applications of optimized electric machinery will enable highly efficient and lightweight systems. This paper will explore the areas where research and development is required to ensure the continued development of power electronics and electric machines to meet the rigorous demands of automotive applications. Additionally, recent advances in automotive related power electronics and electric machinery at Oak Ridge National Laboratory will be explained. 3 refs., 5 figs.

The experimental study on efficiency improvement of turbo machinery supported with magnetic bearings

International Nuclear Information System (INIS)

Park, In Hwang; Park, Young Ho; Han, Dong Chul

2007-01-01

To implement a conventional electromagnetic bearing in small turbo machinery, it has problems such as load capacity and size. Therefore, in this paper, these problems are resolved by using a permanent magnet biased electromagnetic bearing as a thrust bearing of small turbo machinery. Because the flux path of the bearing is designed by reluctance path modulation using an electromagnet and a permanent magnet, the bearing improves upon non-linearity, power consumption, size and load capacity of a conventional electromagnetic bearing. Test rotating the shaft over 500,000DN were carried out to verify the performance of the proposed small turbo machinery. In addition, the relationships between mass flow rate and pressure rise were measured as changing the tip clearance to verify the feasibility of efficiency improvement and active surge control and these results were compared with theoretical results

Establishment of Approximate Analytical Model of Oil Film Force for Finite Length Tilting Pad Journal Bearings

Directory of Open Access Journals (Sweden)

Yongliang Wang

2015-01-01

Full Text Available Tilting pad bearings offer unique dynamic stability enabling successful deployment of high-speed rotating machinery. The model of dynamic stiffness, damping, and added mass coefficients is often used for rotordynamic analyses, and this method does not suffice to describe the dynamic behaviour due to the nonlinear effects of oil film force under larger shaft vibration or vertical rotor conditions. The objective of this paper is to present a nonlinear oil force model for finite length tilting pad journal bearings. An approximate analytic oil film force model was established by analysing the dynamic characteristic of oil film of a single pad journal bearing using variable separation method under the dynamic π oil film boundary condition. And an oil film force model of a four-tilting-pad journal bearing was established by using the pad assembly technique and considering pad tilting angle. The validity of the model established was proved by analyzing the distribution of oil film pressure and the locus of journal centre for tilting pad journal bearings and by comparing the model established in this paper with the model established using finite difference method.

Performance and emission analysis on blends of diesel, restaurant yellow grease and n-pentanol in direct-injection diesel engine.

Science.gov (United States)

Ravikumar, J; Saravanan, S

2017-02-01

Yellow grease from restaurants is typically waste cooking oil (WCO) free from suspended food particles with free fatty acid (FFA) content less than 15%. This study proposes an approach to formulate a renewable, eco-friendly fuel by recycling WCO with diesel (D) and n-pentanol (P) to improve fuel-spray characteristics. Three ternary blends (D50-WCO45-P5, D50-WCO40-P10 and D50-WCO30-P20) were selected based on the stability tests and prepared with an objective to substitute diesel by 50% with up to 45% recycled component (WCO) and up to 20% bio-component (n-pentanol) by volume. The fuel properties of these ternary blends were measured and compared. The emission impacts of these blends on a diesel engine were analysed in comparison with diesel and D50-WCO50 (50% of diesel + 50% of WCO) under naturally articulated and EGR (exhaust gas recirculation) approaches. Doping of n-pentanol showed improved fuel properties when compared to D50-WCO50. Viscosity is reduced up to 45%. Cetane number and density were comparable to that of diesel. Addition of n-pentanol to D50-WCO50 presented improved brake specific fuel consumption (BSFC) for all ternary blends. Brake thermal efficiency (BTE) of D50-WCO30-P20 blend is comparable to diesel due to improved atomization. Smoke opacity reduced, HC emissions increased and CO emissions remained unchanged with doping n-pentanol in the WCO. NOx emission increases with increase in n-pentanol and remained lower than diesel and all load conditions. However, NOx can be decreased by up to threefold using EGR. By adopting this approach, WCO can be effectively reused as a clean energy source by negating environmental hazards before and after its use in diesel engines, instead of being dumped into sewers and landfills.

Fluid machinery application, selection, and design

CERN Document Server

Wright, Terry

2013-01-01

Published nearly a decade ago, Fluid Machinery: Performance, Analysis, and Design quickly became popular with students, professors, and professionals because of its comprehensive and comprehensible introduction to the fluid mechanics of turbomachinery. Renamed to reflect its wider scope and reorganized content, this second edition provides a more logical flow of information that will enhance understanding. In particular, it presents a consistent notation within and across chapters, updating material when appropriate. Although the authors do account for the astounding growth in the field of com

The kinematics of machinery outlines of a theory of machines

CERN Document Server

Reuleaux, Franz

2012-01-01

A classic on the kinematics of machinery, this volume was written by the Father of Kinematics. Reuleaux writes with authority and precision, developing the subject from its fundamentals. 450 figures. 1876 edition.

Investigation Antiwear Properties of Lubricants with the Geo-Modifiers of Friction

Directory of Open Access Journals (Sweden)

I. Levanov

2017-09-01

Full Text Available The article describes the influence of the geo-modifiers of friction on the antiwear properties of lubricants. Geo-modifiers of friction are the fine powders of mineral materials. This work is directed on the investigation the influence of the geo-modifiers of friction in the form of the hard lubricant compositions, which based on a mineral serpentine, on the anti-wear properties of greases and gear oils. This composition is the fine powder serpentine with the addition of components such as chalk, borax, kaolin and talc. We compared the antiwear properties of the greases without geo-modifiers of friction and the antiwear properties of greases containing the geo-modifiers of friction from 0.5 % to 3 %. The Litol-24 and transmission oil TAD-17 was used for testihg. The four-ball machine of friction was used for tests accordance with GOST 9490-75. As geo-modifiers the serpentine was used, the fraction of which has a size from 0.87 microns to 2.2 microns. Such parameter as the wear scar diameter was used for evaluation of the antiwear properties of lubricants. As a result of tests it was established that the antiwear greases properties improved on 26-50 % depending on the concentration of the geo-modifiers of friction based on the pure serpentine.

Managing the exploitation life of the mining machinery for an unlimited duration of time

Directory of Open Access Journals (Sweden)

Vujić Slobodan

2011-01-01

Full Text Available The problem of determining the optimum exploitation life of machinery, namely, the optimum time for machinery and equipment replacement, represents a complex and highly responsible engineering task. Taking into consideration the situation prevailing at coal pit mines in Serbia, the tasks of this rank are very complex and difficult. To make a decision on the replacement of capital equipment and machinery, such as bucket wheel excavators within the mentioned systems, implies a management task of utmost responsibility. It requires high professional and analytical knowledge as well as reliable arguments, based on a multidisciplinary professional approach. In this paper, the authors present their views on the problem of establishing the optimum exploitation life of bucket wheel excavators, offering an algorithm, based on dynamic programming, as a solution.

Noise test system of rotating machinery in nuclear power station based on microphone array

Science.gov (United States)

Chang, Xincai; Guan, Jishi; Qi, Liangcai

2017-12-01

Rotating machinery plays an important role in all walks of life. Once the equipment fails, equipment maintenance and shutdown will cause great social harm and economic losses. Equipment safety operations at nuclear power stations have always been of top priority. It is prone to noise when the equipment is out of order or aging. Failure to find or develop equipment at the initial stage of equipment failure or ageing will pose a serious threat to the safety of the plant’s equipment. In this paper, sound imaging diagnosis technology is applied as a supplementary method to the condition monitoring and diagnosis system of rotating machinery in nuclear power stations. It provides a powerful guarantee for the condition monitoring and fault diagnosis of rotating machinery in nuclear power stations.

Present Situation and Activities of ISO 14000 series in Heavy Machinery Industries; Jukikai meka no taiou jokyo

Energy Technology Data Exchange (ETDEWEB)

Tomisawa, Yukio. [Ishikawajima-Harima Heavy Industries Corp., Tokyo (Japan). Research Institute

1999-01-15

This paper shows the outline of the present situation and activities of ISO14000 series, environmental management system in heavy machinery industries. Today, main heavy machinery industries have already certified to ISO 14001 until this summer. The aim of the introduction of ISO 14001 are to establish the system improvement continuously by PDCA, to have essential elements in international trade and to keep up with the risk management. Some example of conducted ISO 14001 in heavy machinery industries are shown. The trend of heavy machinery industries will be able to predict to three key words, internationalization, network and opening information. The new role expected to environmental material engineer are indicated to research and develop ecomaterial by using LCA and to support the recycling, waste treatment and other technical basis of the environmental management system. (author)

29 CFR 1915.157 - Hand and body protection.

Science.gov (United States)

2010-07-01

... such as skin absorption of harmful substances, severe cuts or lacerations, severe abrasions, punctures... with flammable or combustible materials (such as grease or oil) while engaged in hot work operations or...

Pemanfaatan Abu Tandan Kosong Kelapa Sawit Untuk Menurunkan Kandungan Minyak/Lemak BOD Dan COD Dari Limbah Cair Pabrik Kelapa Sawit

OpenAIRE

Sari, Riris Duma

2011-01-01

An investigation of the utilization of oil palm empty fruit bunch ash to reduce the content of oil/grease, BOD and COD from oil mill effluent. Samples of palm oil mill effluent from wastewater treatment plant of PT Nusantara IV (Persero) oil processing unit sopsa of Padang Lawas district. Samples taken from the last pond will be discharged into the environment. Empty Fruit of Oil Palm Ash taken from the kitchen burning empty fruit bunches PT Nusantara IVB (Persero) units Sosa of Padang Law...

A Modelling Approach to Multibody Dynamics of Fluid Power Machinery with Hydrodynamic Lubrication

DEFF Research Database (Denmark)

Johansen, Per; Rømer, Daniel; Andersen, Torben Ole

2013-01-01

The efficiency potential of the digital displacement technology and the increasing interest in hydraulic transmissions in wind and wave energy applications has created an incentive for development of high efficiency fluid power machinery. Modelling and analysis of fluid power machinery loss...... mechanisms is necessary in order to accommodate this demand. At present fully coupled thermo-elastic models for various tribological interfaces has been presented. However, in order to analyse the interaction between tribological interfaces in fluid power pumps and motors, these interface models needs...

Mining aspects of hard to access oil sands deposits

Energy Technology Data Exchange (ETDEWEB)

Stephenson, G.; Wright, D.; Lukacs, Z. [Norwest Corp., Calgary, AB (Canada)

2006-07-01

While a variety of oil sands mining technologies have been explored since the 1960s, the oil sands industry has generally favoured truck and shovel mining as a proven, low-cost mining solution. However, surface mining economics are affected by the price of bitumen, haul distances, tailings storage and geotechnical constraints. Maintenance, labour and the cost of replacing tires and ground engaging tools also have a significant impact on the economics of surface mining. Large volumes of water are used in surface mining, and remediation of surface mined areas can take hundreds of years. Damage to machinery is common as oil sands are abrasive and adhere to equipment. This presentation examined recent technologies developed to improve the economics of surface mining. Various extraction and tailings technologies were reviewed. Issues concerning the integration of mining and extraction processes were discussed. Various monitoring tools were evaluated. A review of new underground mining options included outlines of: longwall mining; sub-level caving; tunnel boring; and room and pillar extraction techniques. A generalized regional geology was presented. It was concluded that the oil sands surfacing mining industry should concentrate on near-term research needs to improve the performance and economics of proven technologies. Screening studies should also be conducted to determine the focus for the development of underground technologies. refs., tabs., figs.

USING CERAMIC MEMBRANES TO RECYCLE TWO NONIONIC ALKALINE METAL-CLEANING SOLUTIONS

Science.gov (United States)

One ZrO2 ultrafilter (0.05 um pore size) and two a-Al2O3 microfilters (0.2 and 0.8 um) were used to remove one synthetic ester oil and two polyalphaolefin-based and two petroleum hydrocarbon-based oils and greases from two nonionic alkaline cleaning solutions (e.g., Turco 4215-NC...

Production method of hydrogen jet plasma process in hydro machinery

International Nuclear Information System (INIS)

Amini, F.

2007-01-01

The purpose of present paper is to the process of plasma formation in hydro machinery when a hydro turbine operates at various conditions and load rejection. By investigation the power, shock pressure , and impact effects of hydro machinery, it is revealed that energy and hydrogen are generated by the plasma process. The investigation on several turbines of various hydro power plants reveals that cold fusion process in hydro machinery generates hydrogen. The hypothesis concerning the participation of alkaline metals in river water and the atomic nuclei of the runner blade material in the formation of hydrogen are considered. It is possible to assume hydrogen, deuterium, helium, and tritium atoms (based on Dr. Mizuno and Dr. Kanarev theories) that are formed, diffuse into cavitation bubbles. The plasma is generated during the collapse of the bubble; thus, the quantity of burnt hydrogen determine the volume of generating hydrogen and the impact force caused by hydrogen explosion (noise).There are five main notions, which can determine hydrogen and plasma process: (1) turbine power effect, (2) high shock pressure, (3) crack on turbine parts, (4) impacts effects and (4) the lift of rotating parts. The frequency of the excitation lies in a range from 0.786 to 1.095 Hz.In future, it may be possible to design hydro turbines based on the plasma process that generates hydrogen; or there may exist turbines that rotate with a mixture of hydrogen explosion and water energies

Rotating machinery surveillance system reduces plant downtime and radiation exposure

International Nuclear Information System (INIS)

Bohanick, J.S.; Robinson, J.C.; Allen, J.W.

1988-01-01

A rotating machinery surveillance system (RMSS) was permanently installed at Grand Gulf nuclear station (GGNS) as part of a program sponsored by the US Department of Energy whose goal was to reduce radiation exposure to power plant personnel resulting from the inspection, maintenance, and repair of rotating machinery. The RMSS was installed at GGNS in 1983 to continuously monitor 173 analog vibration signals from proximity probes mounted on 26 machine trains and ∼450 process data points via a computer data link. Vibration frequency spectra, i.e., the vibration amplitude versus frequency of vibration, and various characterizations of these spectra are the fundamental data collected by the RMSS for performing machinery diagnostics. The RMSS collects vibration frequency spectra on a daily basis for all the monitored rotating equipment and automatically stores the collected spectra for review by the vibration engineer. Vibration spectra automatically stored by the RMSS fall into categories that include the last normal, alarm, minimum and maximum, past three-day data set, baseline, current, and user-saved spectra. During first and second fuel-cycle operation at GGNS, several significant vibration problems were detected by the RMSS. Two of these are presented in this paper: recirculation pumps and turbine-generator bearing degradation. The total reduction in personnel radiation exposure at GGNS from 1985 to 1987 due to the presence of the RMSS was estimated to be in the range from 49 to 54 person-rem

RESOURCE-SAVING TECHNOLOGY OF CONSTRUCTION MACHINERY OPERATION

Directory of Open Access Journals (Sweden)

Fedosov Sergej Viktorovich

2012-10-01

Depending on the type of membranes and the degree of used oil treatment, recovered oil may be applied for the initially designated purpose, as an additive injected into diesel fuel or delivered to major oil recovery facilities, although the latter purpose requires preliminary improvement of physical and chemical properties of used oil to assure its complete recovery.

Hydrothermal synthesis of copper zirconium phosphate hydrate [Cu(OH)2Zr(HPO4)2·2H2O] and an investigation of its lubrication properties in grease.

Science.gov (United States)

Zhang, Xiaosheng; Xu, Hong; Zuo, Zhijun; Lin, Zhi; Ferdov, Stanislav; Dong, Jinxiang

2013-08-28

Copper zirconium phosphate hydrate (Cu(OH)2Zr(HPO4)2·2H2O, hereafter referred to as Cu-α-ZrP) with high crystallinity was directly synthesized in a NaF-CuO-ZrO-P2O5-H2O system under hydrothermal conditions. The copper ion was confirmed to be an exchangeable cation in the Cu-α-ZrP through elemental analysis and a proton ion exchange process. The crystal structure of the Cu-α-ZrP was determined ab initio by using X-ray powder diffraction data. In the structure, the CuO6 octahedron would be located in an exchangeable atom position. Moreover, Cu-α-ZrP was evaluated as an additive in grease in a four ball test. The maximum nonseizure load (PB, representing the load-carrying capacity) of the base grease containing Cu-α-ZrP was increased from 353 to 1235 N. The excellent load-carrying capacity may be explained by the easier adherence of the material to the worn surface forming a tight protective film.

46 CFR 182.460 - Ventilation of spaces containing machinery powered by, or fuel tanks for, gasoline.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Ventilation of spaces containing machinery powered by, or fuel tanks for, gasoline. 182.460 Section 182.460 Shipping COAST GUARD, DEPARTMENT OF HOMELAND..., gasoline. (a) A space containing machinery powered by, or fuel tanks for, gasoline must have a ventilation...

Optimization of municipal sludge and grease co-digestion using disintegration technologies.

Science.gov (United States)

Bouchy, L; Pérez, A; Camacho, P; Rubio, P; Silvestre, G; Fernández, B; Cano, R; Polanco, M; Díaz, N

2012-01-01

Many drivers tend to foster the development of renewable energy production in wastewater treatment plants as many expectations rely upon energy recovery from sewage sludge, for example through biogas use. This paper is focused on the assessment of grease waste (GW) as an adequate substrate for co-digestion with municipal sludge, as it has a methane potential of 479-710 LCH(4)/kg VS, as well as the evaluation of disintegration technologies as a method to optimize the co-digestion process. With this objective three different pre-treatments have been selected for evaluation: thermal hydrolysis, ultrasound and enzymatic treatment. Results have shown that co-digestion processes without pre-treatment had a maximum increment of 128% of the volumetric methane productivity when GW addition was 23% inlet (at 20 days of HRT and with an OLR of 3.0 kg COD/m(3)d), compared with conventional digestion of sewage sludge alone. Concerning the application of the selected disintegration technologies, all pre-treatments showed improvements in terms of methane yield (51.8, 89.5 and 57.6% more for thermal hydrolysis, ultrasound and enzymatic treatment, respectively, compared with non-pretreated wastes), thermal hydrolysis of GW and secondary sludge being the best configuration as it improved the solubilization of the organic matter and the hydrodynamic characteristics of digestates.

Multiple Cylinder Free-Piston Stirling Machinery

Science.gov (United States)

Berchowitz, David M.; Kwon, Yong-Rak

In order to improve the specific power of piston-cylinder type machinery, there is a point in capacity or power where an advantage accrues with increasing number of piston-cylinder assemblies. In the case of Stirling machinery where primary energy is transferred across the casing wall of the machine, this consideration is even more important. This is due primarily to the difference in scaling of basic power and the required heat transfer. Heat transfer is found to be progressively limited as the size of the machine increases. Multiple cylinder machines tend to preserve the surface area to volume ratio at more favorable levels. In addition, the spring effect of the working gas in the so-called alpha configuration is often sufficient to provide a high frequency resonance point that improves the specific power. There are a number of possible multiple cylinder configurations. The simplest is an opposed pair of piston-displacer machines (beta configuration). A three-cylinder machine requires stepped pistons to obtain proper volume phase relationships. Four to six cylinder configurations are also possible. A small demonstrator inline four cylinder alpha machine has been built to demonstrate both cooling operation and power generation. Data from this machine verifies theoretical expectations and is used to extrapolate the performance of future machines. Vibration levels are discussed and it is argued that some multiple cylinder machines have no linear component to the casing vibration but may have a nutating couple. Example applications are discussed ranging from general purpose coolers, computer cooling, exhaust heat power extraction and some high power engines.

Reprocessing and disposal of used lubricating and process materials. requirements, problems, and solution methods

Energy Technology Data Exchange (ETDEWEB)

Matzke, U D

1978-02-01

A discussion covers West German laws concerning used oil disposal and re-refining (316,000 tons were reprocessed in 1976); disposal of sulfuric acid resins or tar and fuller's earth containing mineral oils by solidification (with added lime, alkali ash, clay, etc.) or pyrolysis; disposal of rolling mill scale and sludge containing oil and grease by rolling with a solid carbonaceous material and processing to high-grade sponge iron; and the breaking of oil-water emulsions.

INTEGRAL ASSESSMENT OF EFFICIENCY OF A FLEET OF AGRICULTURAL MACHINERY AND TRACTORS

Directory of Open Access Journals (Sweden)

V. M. Korotchenya

2015-01-01

Full Text Available An indicator for an integral assessment of efficiency of a fleet of agricultural machinery and tractors is proposed. Its calculating consists in multiplying partial efficiencies together: technical and price efficiency of agricultural production, and eco-efficiency of a fleet of agricultural machinery and tractors. Using an axiomatic method, the concept of efficiency of fleet was studied within broader category of productivity and in wider scales - within agriculture. The most general and obvious statements according to which efficiency of machine and tractor fleet is considered as indirectly settlement size counted proceeding from efficiency of agricultural production, were accepted as axioms. In general, efficiency is a ratio between productivity of an object in question and that of the theoretical ideal or an object with maximum productivity efficiency of which is accepted equal to unity or 100%. Technical efficiency of agricultural production characterizes the ability of an agricultural sector to produce the technically maximum output of agricultural produce obtained from the available resources (land, labor, machines, etc.. Price efficiency evaluates the ability of an agricultural sector to produce output of agricultural produce with regard to employing the optimal mix of resources given their prices. Because the theoretical ideal does not exist, efficiency of an agricultural sector, e.g. in Russia and of its fleet of agricultural machinery and tractors, is measured against agriculture of another country with maximum productivity efficiency of which is accepted as equal to unity or 100 percent. The calculation can be made on the basis of the Data Envelopment Analysis method. It is possible to calculate price and economic efficiency of Russian agriculture (fleet of agricultural machinery and tractors due to use its domestic prices.

Control Systems of Rubber Dryer Machinery Components Using Programmable Logic Control (PLC)

Science.gov (United States)

Hendra; Yulianto, A. S.; Indriani, A.; Hernadewita; Hermiyetti

2018-02-01

Application of programmable logic control (PLC) is widely used on the control systems in the many field engineering such as automotive, aviation, food processing and other industries [1-2]. PLC is simply program to control many automatic activity, easy to use, flexible and others. PLC using the ladder program to solve and regulated the control system component. In previous research, PLC was used for control system of rotary dryer machine. In this paper PLC are used for control system of motion component in the rubber dryer machinery. Component of rubber dryer machine is motors, gearbox, sprocket, heater, drying chamber and bearing. Principle working of rubber dryer machinery is wet rubber moving into the drying chamber by sprocket. Sprocket is driven by motors that conducted by PLC to moving and set of wet rubber on the drying chamber. Drying system uses greenhouse effect by making hanger dryer design in the form of line path. In this paper focused on motion control system motors and sensors drying rubber using PLC. The results show that control system of rubber dryer machinery can work in accordance control input and the time required to dry the rubber.

Bio-composite Nonwoven Media Based on Chitosan and Empty Fruit Bunches for Wastewater Application

International Nuclear Information System (INIS)

Sadikin, Aziatul Niza; Nawawi, Mohd Ghazali Mohd; Othman, Norasikin

2011-01-01

Fibrous filter media in the form of non-woven filters have been used extensively in water treatment as pre-filters or to support the medium that does the separation. Lignocellulosic such as empty fruit bunches have potential to be used as a low cost filter media as they represent unused resources, widely available and are environmentally friendly. Laboratory filtration tests were performed to investigate the potential application of empty fruit bunches that enriched with chitosan as a fiber filter media to remove suspended solids, oil and grease, and organics in terms of chemical oxygen demand from palm oil mill effluent. The present paper studies the effect of chitosan concentration on the filter media performance. Bench-scaled experiment results indicated that pre-treatment using the fiber filtration system removed up to 67.3% of total suspended solid, 65.1% of oil and grease and 46.1% of chemical oxygen demand. The results show that the lignocellulosic fiber filter could be a potential technology for primary wastewater treatment.

Vibration Feature Extraction and Analysis for Fault Diagnosis of Rotating Machinery-A Literature Survey

Directory of Open Access Journals (Sweden)

Saleem Riaz

2017-02-01

Full Text Available Safety, reliability, efficiency and performance of rotating machinery in all industrial applications are the main concerns. Rotating machines are widely used in various industrial applications. Condition monitoring and fault diagnosis of rotating machinery faults are very important and often complex and labor-intensive. Feature extraction techniques play a vital role for a reliable, effective and efficient feature extraction for the diagnosis of rotating machinery. Therefore, developing effective bearing fault diagnostic method using different fault features at different steps becomes more attractive. Bearings are widely used in medical applications, food processing industries, semi-conductor industries, paper making industries and aircraft components. This paper review has demonstrated that the latest reviews applied to rotating machinery on the available a variety of vibration feature extraction. Generally literature is classified into two main groups: frequency domain, time frequency analysis. However, fault detection and diagnosis of rotating machine vibration signal processing methods to present their own limitations. In practice, most healthy ingredients faulty vibration signal from background noise and mechanical vibration signals are buried. This paper also reviews that how the advanced signal processing methods, empirical mode decomposition and interference cancellation algorithm has been investigated and developed. The condition for rotating machines based rehabilitation, prevent failures increase the availability and reduce the cost of maintenance is becoming necessary too. Rotating machine fault detection and diagnostics in developing algorithms signal processing based on a key problem is the fault feature extraction or quantification. Currently, vibration signal, fault detection and diagnosis of rotating machinery based techniques most widely used techniques. Furthermore, the researchers are widely interested to make automatic

Part-time farmers and accidents with agricultural machinery: a moderated mediated model on the role played by frequency of use and unsafe beliefs.

Science.gov (United States)

Caffaro, Federica; Roccato, Michele; Micheletti Cremasco, Margherita; Cavallo, Eugenio

2018-01-25

We aimed at testing a model of the direct and indirect effects of being a part-time farmer on the probability of being involved in an agricultural machinery-related accident, considering the role played by unsafe beliefs and the frequency of use of machinery. Two-hundred and fifty-two Italian men, regular users of agricultural machinery (age: Mean = 45.1 years, standard Deviation = 17.5), were administered a paper-and-pencil questionnaire addressing their relation with work, unsafe beliefs, and previous experience of machinery-related accidents. Being a part-time farmer showed a positive association with unsafe beliefs only among occasional machinery users. Unsafe beliefs in turn showed a positive association with accidents. The study gave a novel contribution to the knowledge of the chain of events connecting part-time farmers with machinery-related accidents. Preventive training interventions targeting part-timer farmers using agricultural machinery just occasionally should be developed.

Detoxification of hexavalent chromium by an indigenous facultative ...

African Journals Online (AJOL)

s

2013-03-06

Mar 6, 2013 ... environmental damage. Hence, easy, economic and eco- friendly techniques are ... (VI) using indigenous microorganism offer a new cost- effective and .... phenol, PCP, oil and grease were well above the permissible limits.

User's Manual for CoEAT Tool

Science.gov (United States)

The Co-EAT users manual is designed to help the anaerobic digestion system operators evaluate the costs and benefits of accepting and processing wasted food, fats, oils and greases (FOG) or other organic materials.

2006 China Machinery and Electronical Products Trade Fair:Ample Fruits Shown

Institute of Scientific and Technical Information of China (English)

无

2006-01-01

@@ 2006 Malaysia China Machinery and Electronical Products Trade Fair, organized by China Council for the Promotion of International Trade(CCPIT), was held in August in Prince World Trade Center(PWTC), Kuala Lumpur.

Research on prediction of agricultural machinery total power based on grey model optimized by genetic algorithm

Science.gov (United States)

Xie, Yan; Li, Mu; Zhou, Jin; Zheng, Chang-zheng

2009-07-01

Agricultural machinery total power is an important index to reflex and evaluate the level of agricultural mechanization. It is the power source of agricultural production, and is the main factors to enhance the comprehensive agricultural production capacity expand production scale and increase the income of the farmers. Its demand is affected by natural, economic, technological and social and other "grey" factors. Therefore, grey system theory can be used to analyze the development of agricultural machinery total power. A method based on genetic algorithm optimizing grey modeling process is introduced in this paper. This method makes full use of the advantages of the grey prediction model and characteristics of genetic algorithm to find global optimization. So the prediction model is more accurate. According to data from a province, the GM (1, 1) model for predicting agricultural machinery total power was given based on the grey system theories and genetic algorithm. The result indicates that the model can be used as agricultural machinery total power an effective tool for prediction.

Implications of material selection on the design of packaging machinery.

Science.gov (United States)

Merritt, J P

2009-01-01

Material selection has significant implications on the design and cost of horizontal-form-fill-seal packaging machinery. To avoid excessive costs, machine redesigns and project delays, material selection must be reconciled early in the project and revisited throughout the construction of the machine.

Scattering transform and LSPTSVM based fault diagnosis of rotating machinery

Science.gov (United States)

Ma, Shangjun; Cheng, Bo; Shang, Zhaowei; Liu, Geng

2018-05-01

This paper proposes an algorithm for fault diagnosis of rotating machinery to overcome the shortcomings of classical techniques which are noise sensitive in feature extraction and time consuming for training. Based on the scattering transform and the least squares recursive projection twin support vector machine (LSPTSVM), the method has the advantages of high efficiency and insensitivity for noise signal. Using the energy of the scattering coefficients in each sub-band, the features of the vibration signals are obtained. Then, an LSPTSVM classifier is used for fault diagnosis. The new method is compared with other common methods including the proximal support vector machine, the standard support vector machine and multi-scale theory by using fault data for two systems, a motor bearing and a gear box. The results show that the new method proposed in this study is more effective for fault diagnosis of rotating machinery.

Development and design of a high pressure carbon dioxide system for the separation of hazardous contaminants from non-hazardous debris

International Nuclear Information System (INIS)

Adkins, C.L.J.; Russick, E.M.; Smith, H.M.; Olson, R.B.

1995-01-01

Under the Department of Energy (DOE)/United States Air Force (USAF) Memorandum of Understanding, a system is being designed that will use high pressure carbon dioxide for the separation of oils, greases, and solvents from non-hazardous solid waste. The contaminants are dissolved into the high pressure carbon dioxide and precipitated out upon depressurization. The carbon dioxide solvent can then be recycled for continued use. Excellent extraction capability for common manufacturing oils, greases, and solvents has been measured. It has been observed that extraction performance follows the dilution model if a constant flow system is used. The solvents tested are extremely soluble and have been extracted to 100% under both liquid and mild supercritical carbon dioxide conditions. These data are being used to design a 200 liter extraction system

THE ROLE OF POSTHARVEST MACHINERIES AND PACKAGING IN MINIMIZING AFLATOXIN CONTAMINATION IN PEANUT

Directory of Open Access Journals (Sweden)

Raffi Paramawati

2016-10-01

Full Text Available As a tropical country with relatively high humidity and temperature, Indonesia is struggling with aflatoxin which frequently contaminates peanut. Aflatoxin is a carcinogenic toxic substance that could cause liver cancer. Due to the increasing concern on food safety, the Indonesian Drugs and Foods Agency specifies the maximum aflatoxin allowed in peanut as much as 20 ppb. However, researches showed that aflatoxin contamination in peanut in Indonesia is much higher than the threshold. The study was carried out to observe the effect of using postharvest machineries and packaging  treatments on aflatoxin contamination in peanut. Reduction of postharvest processes was conducted by using series of machineries, e.g. thresher, dryer, and sheller. Packaging treatments, e.g. vacuum plastic pack, hermetic glass chamber, and polyethylene (PE plastic wrap were carried out during storage at ambient temperature (25-27°C. The results showed that using machineries in postharvest handling produced peanut free from aflatoxin contamination. However, without effective packaging, the aflatoxin level would increase during storage. Hermetic packaging could protect peanut from the mold as indicated by low level of aflatoxin contamination.

Large-Scale Analysis Exploring Evolution of Catalytic Machineries and Mechanisms in Enzyme Superfamilies.

Science.gov (United States)

Furnham, Nicholas; Dawson, Natalie L; Rahman, Syed A; Thornton, Janet M; Orengo, Christine A

2016-01-29

Enzymes, as biological catalysts, form the basis of all forms of life. How these proteins have evolved their functions remains a fundamental question in biology. Over 100 years of detailed biochemistry studies, combined with the large volumes of sequence and protein structural data now available, means that we are able to perform large-scale analyses to address this question. Using a range of computational tools and resources, we have compiled information on all experimentally annotated changes in enzyme function within 379 structurally defined protein domain superfamilies, linking the changes observed in functions during evolution to changes in reaction chemistry. Many superfamilies show changes in function at some level, although one function often dominates one superfamily. We use quantitative measures of changes in reaction chemistry to reveal the various types of chemical changes occurring during evolution and to exemplify these by detailed examples. Additionally, we use structural information of the enzymes active site to examine how different superfamilies have changed their catalytic machinery during evolution. Some superfamilies have changed the reactions they perform without changing catalytic machinery. In others, large changes of enzyme function, in terms of both overall chemistry and substrate specificity, have been brought about by significant changes in catalytic machinery. Interestingly, in some superfamilies, relatives perform similar functions but with different catalytic machineries. This analysis highlights characteristics of functional evolution across a wide range of superfamilies, providing insights that will be useful in predicting the function of uncharacterised sequences and the design of new synthetic enzymes. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Electric machinery and drives in thermal power stations

International Nuclear Information System (INIS)

1974-01-01

The following subjects were dealt with during the VDE meeting: 1) Requirements made by the electric network on the generators and their excitation equipment, and the influence thereof on their design; 2) requirements made by the power station process on the electric drives and the influence thereof on type and design; 3) requirements made on protective measures from the point of the electric power station machinery. (TK) [de

Targeting Transcription Elongation Machinery for Breast Cancer Therapy

Science.gov (United States)

2017-05-01

ABSTRACT: This project focuses on the important but under-studied role of the P-TEFb- dependent transcription elongation machinery in human breast...molecule CDK9 inhibitors can be used to halt breast cancer metastasis. 8 experimental groups to test various drug dosage and frequency regimes will...tumor cells, which are said to be ’ addicted ’ to this protein. Consistently, pharmacological inhibition of Hsp90 has demonstrated great promise in

Progress in control equipment for fuel-handling machinery

International Nuclear Information System (INIS)

Nutting, B.A.

1986-01-01

The paper outlines the development of the equipment used to control the fuel-handling machinery associated with nuclear reactors, from the early electromechanical equipment, through solid-state switching logic to programmable controllers and microprocessors. The control techniques have developed along with the technology, and modern systems offer versatility, reliability and ease of design, operation and maintenance. Future trends and developments are discussed together with possible limiting factors. (author)

Application of logical analysis of data to machinery-related accident prevention based on scarce data

International Nuclear Information System (INIS)

Jocelyn, Sabrina; Chinniah, Yuvin; Ouali, Mohamed-Salah; Yacout, Soumaya

2017-01-01

This paper deals with the application of Logical Analysis of Data (LAD) to machinery-related occupational accidents, using belt-conveyor-related accidents as an example. LAD is a pattern recognition and classification approach. It exploits the advancement in information technology and computational power in order to characterize the phenomenon under study. The application of LAD to machinery-related accident prevention is innovative. Ideally, accidents do not occur regularly, and as a result, companies have little data about them. The first objective of this paper is to demonstrate the feasibility of using LAD as an algorithm to characterize a small sample of machinery-related accidents with an adequate average classification accuracy. The second is to show that LAD can be used for prevention of machinery-related accidents. The results indicate that LAD is able to characterize different types of accidents with an average classification accuracy of 72–74%, which is satisfactory when compared with other studies dealing with large amounts of data where such a level of accuracy is considered adequate. The paper shows that the quantitative information provided by LAD about the patterns generated can be used as a logical way to prioritize risk factors. This prioritization helps safety practitioners make decisions regarding safety measures for machines. - Highlights: • LAD is presented as an innovative approach to prevent machinery-related accidents. • LAD is applied to a very small database of belt-conveyor-related accidents. • Despite scarce data, LAD generates patterns with adequate classification accuracy. • The patterns characterize different types of belt-conveyor-related accidents. • The patterns are useful to belt conveyor risk identification and risk estimation.

EXPLORING LINKS AMONG INVENTORY AND FINANCIAL PERFORMANCE IN THE AGRICULTURAL MACHINERY INDUSTRY

Directory of Open Access Journals (Sweden)

Dimitris Folinas

2014-10-01

Full Text Available The paper aims to investigate the effects of Inventory Turnover and Inventory Days on firm performance in the United Kingdom agricultural machinery industry by examining past literature reviews and empirical evidence of a primary research. Specific performance measures such as Earnings before Interest and Tax to Sales Ratio, Gross Profit to Sales Ratio, and Return on Assets are examined by conducting statistical analyses to determine the correlations between inventory and financial performance in agricultural machinery industry. The analysis of Inventory Turnover with financial performance measures doesn’t indicate any links between these variables. Furthermore, based on the results, Inventory Days plays a role in the financial performance of organisations however to varying degrees.

Designing a machinery control system (MCS) security testbed

OpenAIRE

Desso, Nathan H.

2014-01-01

Approved for public release; distribution is unlimited Industrial control systems (ICS) face daily cyber security threats, can have a significant impact to the security of our nation, and present a difficult challenge to defend. Critical infrastructures, including military systems like the machinery control systems (MCS) found onboard modern U.S. warships, are affected because of their use of commercial automation solutions. The increase of automated control systems within the U.S. Navy sa...

Fault diagnosis in rotating machinery by vibration analysis

International Nuclear Information System (INIS)

Behzad, M.; Asayesh, M.

2002-01-01

Dynamic behavior of unbalanced bent shaft has been investigated in this research. Finite element method is used for unbalance response calculation of a bent shaft. The result shows the effect of bent on the unbalance response. The angle between bent vector and unbalance force, position and type of supports, shaft diameter and disk position can affect the outcome. The results of this research can significantly help in fault diagnosis in rotating machinery

Analysis of electric machinery and drive systems

CERN Document Server

Krause, Paul C; Sudhoff, Scott D; Pekarek, Steven

2013-01-01

Introducing a new edition of the popular reference on machine analysis Now in a fully revised and expanded edition, this widely used reference on machine analysis boasts many changes designed to address the varied needs of engineers in the electric machinery, electric drives, and electric power industries. The authors draw on their own extensive research efforts, bringing all topics up to date and outlining a variety of new approaches they have developed over the past decade. Focusing on reference frame theory that has been at the core of this work since the first edition, th

Electrification of agricultural machinery; Elektrifizierung von Landmaschinen

Energy Technology Data Exchange (ETDEWEB)

Goetz, Manuel; Grad, Karl; Weinmann, Olrik [ZF Friedrichshafen AG, Friedrichshafen (Germany)

2012-10-15

As early as 2009, ZF exhibited a generator system for agricultural machinery at Agritechnica under the name Terra+ which consisted of an electric motor in the transmission housing. As part of the ElecTra project, the company is now presenting its first tractor prototype with this generator system at Agritechnica 2011. The project involves combining the electrification of the tractor's auxiliary systems with electric drives for an attachment. The electrification of the implement was carried out in cooperation with Amazone, manufacturer of implements for the agricultural industry. (orig.)

Effects of processing methods and commercial storage conditions on the extra virgin olive oil quality indexes

Directory of Open Access Journals (Sweden)

Kiritsakis, A.

2007-09-01

Full Text Available The effect of machinery groups, packing materials and light intensities was ascertained on indices of oxidative deterioration, peroxide value, and extinction coefficient K232 and K270 of extra virgin olive oil for one season of olive harvesting in an effort to simulate commercial storage conditions. It was revealed that during the storage of olive oil the peroxide value was significantly affected by the type of extraction machinery, packing material and light intensity. It is significant that oil exposed to diffused daylight and artificial light attained maximum PV in the second or third month of storage and de creased thereafter, while samples stored in the dark attained their maximum PV during the sixth month of storage. Oil samples extracted using the centrifugal type of machines and kept in glass containers in the dark had higher peroxide values than those extracted by the classic method. The rate of changes of the PV and the two indices K232 and K270 was also affected similarly by the type of machinery, packing material and light intensity.El efecto de la maquinaria, el material de envasado y la intensidad de luz fue relacionado con los índices de deterioración oxidativa, índice de peróxidos (IP y coeficientes de extinción K232 y K270 del aceite de oliva virgen extra durante una campaña de cosecha de aceituna en un esfuerzo por simular las condiciones de almacenamiento comercial. Esto reveló que durante el almacenamiento del aceite de oliva el índice de peróxidos fue afectado significativamente por el tipo de maquinaria de extracción, el material de envasado y la intensidad de luz. Es significativo que el aceite expuesto a la luz diaria difusa y a la artificial alcanzara el máximo IP en el segundo o tercer mes de almacenamiento, decreciendo a partir de este momento, mientras que las muestras almacenadas en oscuridad no alcanzaban su máximo IP hasta el sexto mes de conservación. Las muestras de aceite extraídas con centr

Eye Injuries at Home

Science.gov (United States)

... by the Numbers — Infographic Five Steps to Safer Champagne Celebrations Eye Injuries at Home Leer en Español: ... that can splatter hot grease or oil. Opening champagne bottles during a celebration. Drilling or hammering screws ...

The Machinery for Enforcement of Domestic Arbitral Awards in Nigeria

African Journals Online (AJOL)

Nnamdi Azikiwe University Journal of International Law and Jurisprudence ... Arbitration is a private means of resolving dispute which is resorted to, chiefly because the parties choose to avoid as much as possible employing the state machinery for dispute resolution, namely the court and its dreaded time consuming ...

Guidelines for meeting emission regulations for rotating machinery with mechanical seals

Science.gov (United States)

Mechanical seals have played a major role during many years in minimizing emissions to atmosphere in rotating machinery. A review is presented of the continuing innovations and new technologies to improve mechanical seal performance in terms of emissions.

The iron-sulfur cluster assembly machineries in plants: current knowledge and open questions

Science.gov (United States)

Couturier, Jérémy; Touraine, Brigitte; Briat, Jean-François; Gaymard, Frédéric; Rouhier, Nicolas

2013-01-01

Many metabolic pathways and cellular processes occurring in most sub-cellular compartments depend on the functioning of iron-sulfur (Fe-S) proteins, whose cofactors are assembled through dedicated protein machineries. Recent advances have been made in the knowledge of the functions of individual components through a combination of genetic, biochemical and structural approaches, primarily in prokaryotes and non-plant eukaryotes. Whereas most of the components of these machineries are conserved between kingdoms, their complexity is likely increased in plants owing to the presence of additional assembly proteins and to the existence of expanded families for several assembly proteins. This review focuses on the new actors discovered in the past few years, such as glutaredoxin, BOLA and NEET proteins as well as MIP18, MMS19, TAH18, DRE2 for the cytosolic machinery, which are integrated into a model for the plant Fe-S cluster biogenesis systems. It also discusses a few issues currently subjected to an intense debate such as the role of the mitochondrial frataxin and of glutaredoxins, the functional separation between scaffold, carrier and iron-delivery proteins and the crosstalk existing between different organelles. PMID:23898337

Application of a biological process for decontamination of soils in the far north

International Nuclear Information System (INIS)

Pouliot, Y.; Sansregret, J.-L.

1994-01-01

The site of a diesel-fuelled power station in the extreme north of Quebec (62 degree latitude) was contaminated with hydrocarbons. The site was characterized by typical Arctic conditions: presence of permafrost, limited land transport facilities, restricted availability of machinery and equipment, and scarcity of skilled labor and specialized services. To remediate the site, it was decided to excavate the contaminated soil and subject it to a biological treatment process. The soil was piled on an impermeable base inside of the old power station building and the following parameters were controlled in order to optimize the biodegradation of the hydrocarbons: temperature, humidity, pH, presence of hydrocarbon degrading microorganisms, and concentrations of oxygen, nitrogen, and phosphorus in the soil. Samples were analyzed to monitor the performance of the biodegradation process. In less than 12 weeks, of treatment, an inital hydrocarbon content estimated at 6,400 mg/kg of oils and greases was reduced to 750 mg/kg, corresponding to a level acceptable for residential areas. Indigenous microorganisms capable of degrading hydrocarbons were already present in the native soil in sufficient quantity, and their performance improved when the soil conditions were optimized. 1 fig., 3 tabs

Application of Functional Link Artificial Neural Network for Prediction of Machinery Noise in Opencast Mines

Directory of Open Access Journals (Sweden)

Santosh Kumar Nanda

2011-01-01

Full Text Available Functional link-based neural network models were applied to predict opencast mining machineries noise. The paper analyzes the prediction capabilities of functional link neural network based noise prediction models vis-à-vis existing statistical models. In order to find the actual noise status in opencast mines, some of the popular noise prediction models, for example, ISO-9613-2, CONCAWE, VDI, and ENM, have been applied in mining and allied industries to predict the machineries noise by considering various attenuation factors. Functional link artificial neural network (FLANN, polynomial perceptron network (PPN, and Legendre neural network (LeNN were used to predict the machinery noise in opencast mines. The case study is based on data collected from an opencast coal mine of Orissa, India. From the present investigations, it could be concluded that the FLANN model give better noise prediction than the PPN and LeNN model.

Hsc70/Hsp90 chaperone machinery mediates ATP-dependent RISC loading of small RNA duplexes.

Science.gov (United States)

Iwasaki, Shintaro; Kobayashi, Maki; Yoda, Mayuko; Sakaguchi, Yuriko; Katsuma, Susumu; Suzuki, Tsutomu; Tomari, Yukihide

2010-07-30

Small silencing RNAs--small interfering RNAs (siRNAs) or microRNAs (miRNAs)--direct posttranscriptional gene silencing of their mRNA targets as guides for the RNA-induced silencing complex (RISC). Both siRNAs and miRNAs are born double stranded. Surprisingly, loading these small RNA duplexes into Argonaute proteins, the core components of RISC, requires ATP, whereas separating the two small RNA strands within Argonaute does not. Here we show that the Hsc70/Hsp90 chaperone machinery is required to load small RNA duplexes into Argonaute proteins, but not for subsequent strand separation or target cleavage. We envision that the chaperone machinery uses ATP and mediates a conformational opening of Ago proteins so that they can receive bulky small RNA duplexes. Our data suggest that the chaperone machinery may serve as the driving force for the RISC assembly pathway. Copyright 2010 Elsevier Inc. All rights reserved.

Anaerobic/aerobic treatment of greywater via UASB and MBR for unrestricted reuse.

Science.gov (United States)

Abdel-Shafy, Hussein I; Al-Sulaiman, Ahmed Makki; Mansour, Mona S M

2015-01-01

The aim of the present study was to investigate the efficiency of integrated up-flow anaerobic sludge blanket (UASB) as anaerobic system followed by membrane bioreactor (MBR) as aerobic system for the treatment of greywater for unrestricted reuse. Pilot-scale UASB and MBR units were installed and operated in the NRC, Egypt. Real raw greywater was subjected to UASB and the effluent was further treated with microfiltration MBR. The necessary trans-membrane pressure difference is applied by the water head above the membrane (gravity flow) without any energy input. The average characteristics of the raw greywater were 95, 392, 298, 10.45, 0.4, 118.5 and 28 mg/L for total suspended solids (TSS), chemical oxygen demand (COD), biochemical oxygen demand (BOD), total phosphates, nitrates, oil and grease, and total Kjeldahl nitrogen (TKN), respectively. The pH was 6.71. The UASB treatment efficiency reached 19.3, 57.8, 67.5 and 83.7% for TSS, COD, BOD5 and oil and grease, respectively. When the UASB effluent was further treated with MBR, the overall removal rate achieved 97.7, 97.8, 97.4 and 95.8% for the same parameters successively. The characteristics of the final effluent reached 2.5, 8.5, 6.1, 0.95, 4.6 and 2.3 mg/L for TSS, COD, BOD, phosphates, oil and grease and TKN, respectively. This final treated effluent could cope with the unrestricted water reuse of local Egyptian guidelines.

DIESEL ENGINE SYSTEMS. AGRICULTURAL MACHINERY--SERVICE OCCUPATIONS, MODULE NUMBER 15.

Science.gov (United States)

Ohio State Univ., Columbus. Center for Vocational and Technical Education.

ONE OF A SERIES DESIGNED TO HELP TEACHERS PREPARE POSTSECONDARY STUDENTS FOR AGRICULTURAL MACHINERY SERVICE OCCUPATIONS AS PARTS MEN, MECHANICS, MECHANIC'S HELPERS, AND SERVICE SUPERVISORS, THIS GUIDE AIMS TO DEVELOP STUDENT UNDERSTANDING OF THE CONSTRUCTION AND OPERATING PRINCIPLES OF DIESEL ENGINES. IT WAS DEVELOPED BY A NATIONAL TASK FORCE ON…

Sources of pollution

Indian Academy of Sciences (India)

First page Back Continue Last page Overview Graphics. Sources of pollution. Domestic wastewater (Sewage). Organic matter; Nitrogen & phosphorus; Pathogens, viruses, …. Agricultural runoff. Nitrogen & phosphorus; Pesticides; Industrial effluents; Organics (oil &grease, pigments, phenols, organic matter ….) Heavy ...

A full-scale biological aerated filtration system application in the ...

African Journals Online (AJOL)

owner

tanks, gravel filter and finally sand anthracite (3:1 by volume) filter. ... sedimentation of the wastewater for six hours reduced the COD, BOD, and ... suspended solids, pigments color and oil and grease. ... The sludge was been dredged every.

40 CFR 421.304 - Standards of performance for new sources.

Science.gov (United States)

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary and... Chromium (total) 0.474 0.192 Lead 0.359 0.167 Nickel 0.705 0.474 Titanium 0.679 0.295 Oil and grease 12.820...

Impact of urban and industrial effluents on the coastal marine environment in Oran, Algeria.

Science.gov (United States)

Tayeb, A; Chellali, M R; Hamou, A; Debbah, S

2015-09-15

In Algeria most of the urban waste water is dumped without treatment into the Sea. It is tremendously important to assess the consequences of organic matter rich sewage on marine ecosystem. In this study we investigated the effects of industrial and urban sewage on the dissolved oxygen (O2), chemical oxygen demand (COD), biochemical oxygen demands (BOD5), pH, salinity, electrical conductivity (EC), Metal element (Hg, Pb, Cu, Ni, Cr, Cd), petroleum hydrocarbons (HC), oil and grease (OG) in Bay of Oran, Algeria. A ten-year follow-up research showed that the concentrations of oil and grease released into the bionetwork are of higher ecological impact and this needs to be given the desired consideration. Information on bathing water quality revealed that the most beaches in Oran are under the national environmental standard limit. Copyright © 2015 Elsevier Ltd. All rights reserved.

Segregation of solid waste from a fish-processing industry: a sustainable action

Directory of Open Access Journals (Sweden)

Yeda dos Santos Silva

2018-05-01

Full Text Available Segregation techniques represent a sustainable alternative to minimize wastes of raw material in processing industries. This study considered the premise; its purpose was to use segregation techniques to determine the theoretical removal rate of solid compounds present in processing effluents, in order to support the sustainable development of the fish industry. The removal rates obtained for different treatments were evaluated for the parameters: total solids, organic matter and oils and greases, and the efficiency of the segregation of the effluent streams in the different stages of fish processing was evaluated through descriptive statistical analysis. The segregation recovered from 31% to 70% of total solids; from 15% to 97.50% of organic matter, and from 10% to 63% of oils and greases. These results indicates that the raw material can be used in new products, leading to reduced final-effluent concentration.

Updating the model TREMOD - Mobile Machinery (TREMOD-MM); Aktualisierung des Modells TREMOD - Mobile Machinery (TREMOD-MM)

Energy Technology Data Exchange (ETDEWEB)

Helms, Hinrich; Lambrecht, Udo; Knoerr, Wolfram [ifeu - Institut fuer Energie- und Umweltforschung Heidelberg gGmbH, Heidelberg (Germany)

2010-05-15

In the context of the project ''Development of a model for the computation of the air pollutant emissions and the fuel consumption of combustion engines in mobile devices and machines'', the Institute for Energy and Environmental Research GmbH (Heidelberg, Federal Republic of Germany) has created the model TREMOD-MM (TREMOD Mobile Machinery). Thus a detailed computation of the emissions from mobile devices and machines in the agriculture, construction industry, forestry and gardening as well as the sport shipping and passenger shipping can be accomplished. Strongly differentiated data are considered to the age structure, engine performance, use and emission behaviour. Thus it is possible to compute the emissions for different scenarios in high degree of detail.

TREATMENT OF PRODUCED OIL AND GAS WATERS WITH SURFACTANT-MODIFIED ZEOLITE

Energy Technology Data Exchange (ETDEWEB)

Lynn E. Katz; R.S. Bowman; E.J. Sullivan

2003-11-01

Co-produced water from the oil and gas industry accounts for a significant waste stream in the United States. It is by some estimates the largest single waste stream in the country, aside from nonhazardous industrial wastes. Characteristics of produced water include high total dissolved solids content, dissolved organic constituents such as benzene and toluene, an oil and grease component, and chemicals added during the oil-production process. While most of the produced water is disposed via reinjection, some must be treated to remove organic constituents before the water is discharged. Current treatment options are successful in reducing the organic content; however, they cannot always meet the levels of current or proposed regulations for discharged water. Therefore, an efficient, cost-effective treatment technology is needed. Surfactant-modified zeolite (SMZ) has been used successfully to treat contaminated ground water for organic and inorganic constituents. In addition, the low cost of natural zeolites makes their use attractive in water-treatment applications. This report summarizes the work and results of this four-year project. We tested the effectiveness of surfactant-modified zeolite (SMZ) for removal of BTEX with batch and column experiments using waters with BTEX concentrations that are comparable to those of produced waters. The data from our experimental investigations showed that BTEX sorption to SMZ can be described by a linear isotherm model, and competitive effects between compounds were not significant. The SMZ can be readily regenerated using air stripping. We field-tested a prototype SMZ-based water treatment system at produced water treatment facilities and found that the SMZ successfully removes BTEX from produced waters as predicted by laboratory studies. When compared to other existing treatment technologies, the cost of the SMZ system is very competitive. Furthermore, the SMZ system is relatively compact, does not require the storage of

40 CFR 428.32 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Science.gov (United States)

2010-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS RUBBER MANUFACTURING POINT SOURCE CATEGORY Solution...) (1) English units (lb/1,000 lb of product) COD 5.91 3.94 BOD5 0.60 .40 TSS 0.98 .65 Oil and grease 0...

Hybridisation of powertrains for construction machinery; Hybridisierung von Antriebsstraengen fuer Baumaschinen

Energy Technology Data Exchange (ETDEWEB)

Mohr, Mark; Goetz, Manuel; Fellmann, Martin [ZF Friedrichshafen AG (Germany). Vorentwicklung Arbeitsmaschinen-Antriebe; Brehmer, Udo [ZF Passau GmbH (Germany). Entwicklung Baumaschinengetriebe

2010-04-15

Increasing fuel prices and increased environmental requirements lead, for construction machinery, to an increased importance of measures to reduce fuel consumption. The hybrid drive in this sector could become an economical option by using synergies for example with the commercial vehicle section. (orig.)

Energy-autonomous wireless vibration sensor for condition-based maintenance of machinery

NARCIS (Netherlands)

Wang, Z.; Bouwens, F.; Vullers, R.; Petré, F.; Devos, S.

2011-01-01

This paper addresses the development of an energy-autonomous wireless vibration sensor for condition-based monitoring of machinery. Such technology plays an increasingly important role in modern manufacturing industry. In this work, energy harvesting is realized by resorting to a custom designed

Cell secretion machinery: Studies using the AFM

International Nuclear Information System (INIS)

Jena, Bhanu P.

2006-01-01

A new field in biology, 'nano-cell biology', has emerged from the successful use of force microscopy in understanding the structure and dynamics of cells and biomolecules, at nm resolution and in real time. Atomic force microscopy, in combination with conventional tools and approaches (electron microscopy, electrophysiology, X-ray diffraction, photon correlation spectroscopy, mass spectroscopy, biochemistry, and molecular biology), has revealed for the first time, the universal molecular machinery and mechanism of secretion in cells. Secretion occurs in all living cells and involves the delivery of intracellular products to the cell exterior. Secretory products are packaged and stored in membranous sacs or vesicles within the cell. When the cell needs to secrete these products, the secretory vesicles containing them, dock and fuse at plasma membrane-associated supramolecular structures called Porosome, to release their contents. Specialized cells for neurotransmission, enzyme secretion, or hormone release utilize a highly regulated secretory process. During secretion, swelling of secretory vesicles results in a build-up of intravesicular pressure, allowing expulsion of vesicular contents. The extent of vesicle swelling dictates the amount of vesicular contents expelled. The discovery of the porosome as the universal secretory machinery, its isolation, its structure and dynamics at nm resolution and in real time, its biochemical composition and functional reconstitution into artificial lipid membrane, have been determined. The molecular mechanism of secretory vesicle swelling, and the fusion of opposing bilayers, i.e., the fusion of secretory vesicle membrane at the base of the porosome membrane, has also been resolved

Motion control of multi-actuator hydraulic systems for mobile machineries: Recent advancements and future trends

Science.gov (United States)

Xu, Bing; Cheng, Min

2018-06-01

This paper presents a survey of recent advancements and upcoming trends in motion control technologies employed in designing multi-actuator hydraulic systems for mobile machineries. Hydraulic systems have been extensively used in mobile machineries due to their superior power density and robustness. However, motion control technologies of multi-actuator hydraulic systems have faced increasing challenges due to stringent emission regulations. In this study, an overview of the evolution of existing throttling control technologies is presented, including open-center and load sensing controls. Recent advancements in energy-saving hydraulic technologies, such as individual metering, displacement, and hybrid controls, are briefly summarized. The impact of energy-saving hydraulic technologies on dynamic performance and control solutions are also discussed. Then, the advanced operation methods of multi-actuator mobile machineries are reviewed, including coordinated and haptic controls. Finally, challenges and opportunities of advanced motion control technologies are presented by providing an overall consideration of energy efficiency, controllability, cost, reliability, and other aspects.

Robust IFE Based Order Analysis of Rotating Machinery in Virtual Instrument

International Nuclear Information System (INIS)

Guo, Y; Chi, Y L; Huang, Y Y; Qin, S R

2006-01-01

Character analysis plays an important role in fault-find and diagnosis of rotating machinery. Order analysis is one of the major methods in character analysis for the analysis of non-stationary vibration signals in run-up or coast down of rotating machinery. An order analysis method, which employs instantaneous frequency estimation based on time-frequency analysis, is introduced. In contrast with traditional order analysis methods, this method avoids the use of tachometer and other special hardware; hence it makes the application of order analysis simplified. The order analysis introduced in the paper with the character that only software is depended for order tracking makes it specially satisfy the requirement of Virtual Instruments. Corresponding order analysis items, such as order spectrum, order spectrum matrix and tracking order spectrum etc., which are applied in Virtual Instruments, are also introduced. A test example is provided to demonstrate the validity of the method presented

Research on monitoring technology of axial gap change about high-speed rotating machinery

International Nuclear Information System (INIS)

Zhang Xiaochan; Liu Fanglei; Hu Shihua; Xie Qing; Li Zhen

2014-01-01

This paper describes that the only measuring point of high-speed rotating machinery (speed monitoring transducer) measuring the operation of the axial gap change and application. According to mechanism analysis the speed monitoring transducer's signal, prove its amplitude changes including the axial gap change information. To carry out the speed monitoring transducer qualitative and quantitative axial gap change research, Find the output signal amplitude and clearance change corresponding relationship formula of speed monitoring transducer, define the measurement method. Based on the above analsis, manufacture the single channel measurement devices and multiple unit measurement system, provide an important fault decision of high-speed rotating machinery, it can be applied to new equipment development and production. (authors)

Fault Severity Estimation of Rotating Machinery Based on Residual Signals

Directory of Open Access Journals (Sweden)

Fan Jiang

2012-01-01

Full Text Available Fault severity estimation is an important part of a condition-based maintenance system, which can monitor the performance of an operation machine and enhance its level of safety. In this paper, a novel method based on statistical property and residual signals is developed for estimating the fault severity of rotating machinery. The fast Fourier transformation (FFT is applied to extract the so-called multifrequency-band energy (MFBE from the vibration signals of rotating machinery with different fault severity levels in the first stage. Usually these features of the working conditions with different fault sensitivities are different. Therefore a sensitive features-selecting algorithm is defined to construct the feature matrix and calculate the statistic parameter (mean in the second stage. In the last stage, the residual signals computed by the zero space vector are used to estimate the fault severity. Simulation and experimental results reveal that the proposed method based on statistics and residual signals is effective and feasible for estimating the severity of a rotating machine fault.

Effects of high-gradient magnetic fields on living cell machinery

International Nuclear Information System (INIS)

Zablotskii, V; Lunov, O; Kubinova, S; Polyakova, T; Dejneka, A; Sykova, E

2016-01-01

A general interest in biomagnetic effects is related to fundamental studies of the influence of magnetic fields on living objects on the cellular and whole organism levels. Emerging technologies offer new directions for the use of high-gradient magnetic fields to control cell machinery and to understand the intracellular biological processes of the emerging field of nanomedicine. In this review we aim at highlighting recent advances made in identifying fundamental mechanisms by which magnetic gradient forces act on cell fate specification and cell differentiation. The review also provides an analysis of the currently available magnetic systems capable of generating magnetic fields with spatial gradients of up to 10 MT m −1 , with the focus on their suitability for use in cell therapy. Relationships between experimental factors and underlying biophysical mechanisms and assumptions that would ultimately lead to a deeper understanding of cell machinery and the development of more predictive models for the evaluation of the effects of magnetic fields on cells, tissue and organisms are comprehensively discussed. (topical review)

40 CFR 80.1100 - How is the statutory default requirement for 2006 implemented?

Science.gov (United States)

2010-07-01

..., greases, and oils, sugarcane, sugar beets, sugar components, tobacco, potatoes, or other biomass; or (B... cellulosic biomass ethanol, waste derived ethanol, biodiesel, and any blending components derived from renewable fuel. (2) Cellulosic biomass ethanol means ethanol derived from any lignocellulosic or...

Designing Bioretention Systems to Improve Nitrogen Removal - poster

Science.gov (United States)

Rain gardens, also referred to as bioretention systems, are designed primarily to infiltrate stormwater flow and reduce surface runoff and peak flows to receiving streams. Additionally, they are known to remove stressors from urban stormwater runoff, including oil and grease, pho...

Vibration sensor data denoising using a time-frequency manifold for machinery fault diagnosis.

Science.gov (United States)

He, Qingbo; Wang, Xiangxiang; Zhou, Qiang

2013-12-27

Vibration sensor data from a mechanical system are often associated with important measurement information useful for machinery fault diagnosis. However, in practice the existence of background noise makes it difficult to identify the fault signature from the sensing data. This paper introduces the time-frequency manifold (TFM) concept into sensor data denoising and proposes a novel denoising method for reliable machinery fault diagnosis. The TFM signature reflects the intrinsic time-frequency structure of a non-stationary signal. The proposed method intends to realize data denoising by synthesizing the TFM using time-frequency synthesis and phase space reconstruction (PSR) synthesis. Due to the merits of the TFM in noise suppression and resolution enhancement, the denoised signal would have satisfactory denoising effects, as well as inherent time-frequency structure keeping. Moreover, this paper presents a clustering-based statistical parameter to evaluate the proposed method, and also presents a new diagnostic approach, called frequency probability time series (FPTS) spectral analysis, to show its effectiveness in fault diagnosis. The proposed TFM-based data denoising method has been employed to deal with a set of vibration sensor data from defective bearings, and the results verify that for machinery fault diagnosis the method is superior to two traditional denoising methods.

DETERMINATION OF AGRICULTURAL MACHINERY OPERATORS’ OPINIONS ABOUT THE CABIN COMFORT IN ESKİŞEHİR

Directory of Open Access Journals (Sweden)

Özge ACARBAŞ BALTACI

2015-08-01

Full Text Available Comfort has a great importance in the interior design of tractor and agricultural machinery cabins. Operators are exposed to muscoskeletal system disorders since they spend long time periods during the day in these vehicles. There is a few work in the literature reporting operators’ opinions about cabin comfort of these machineries. In this study, a questionnaire was conducted in order to get information about agricultural machinery operators’ opinions about the comfort of their vehicles. Tractor cabins and combine harvester machine cabins were selected as machineries. The study was conducted in Eskişehir in Turkey. Questionnaire was composed of four groups of questions and five ordered response levels were used in the Likert's scale. Demographic questions, general questions about the machine, personal evaluation questions and open ended questions were asked to the operators. After the questionnaire completed, collected data were classified according to the machine type. Frequency tables were used to present the results. Visibility and the accessibility were the most satisfied issues for the tractor operators with 55.9% and 55.4% percentages, respectively. Seat comfort has the highest satisfaction degree with 43.7% for the combine harvester operators. Cronbach Alpha reliability coefficient was used for the satisfaction questions in the applied questionnaire. The reliability of the study was high with coefficients of 0.878 and 0.940 for the tractor and combine harvester questionnaires, respectively. This study will support design and development process of new products by considering operator opinions.

Caracterização físico-química de resíduos oleosos do saneamento e dos óleos e graxas extraídos visando a conversão em biocombustíveis

Directory of Open Access Journals (Sweden)

Jairo Pinto de Oliveira

2014-01-01

Full Text Available Oily waste from sanitation processes was characterized for its potential use in the generation of biofuels. The waste residues studied showed high levels of oil and grease, reaching up to 87% (m/m in a grease trap of a food company, showing that these residues can be utilized for the production of biofuels. The results revealed high levels of moisture and saponification as well as high levels of free fatty acids (FFA. Analysis of chromatographic profiles (HPLC showed great heterogeneity of the fatty acids contained in the sample, and a predominance of palmitic, oleic, linoleic and linolenic acids.

Conflicting views on the membrane fusion machinery and the fusion pore

DEFF Research Database (Denmark)

Sørensen, Jakob B

2009-01-01

of the assembly of the fusogenic SNARE-complex. Here, I review conflicting views on the function of the core fusion machinery consisting of the SNAREs, Munc18, complexin, and synaptotagmin. Munc18 controls docking of vesicles to the plasma membrane and initial SNARE-complex assembly, whereas complexin...

Technical development of fluid machinery area

International Nuclear Information System (INIS)

Chung, Kyung Nam; Kim, Jin Young; Kim, Yang Ik

2008-01-01

In this paper, recent research activity of Hyundai Heavy Industries in the fluid machinery area is introduced. Technical development has been carried out in pumps, turbines, construction equipment, side thrusters, engine lubrication flow, etc. Here the technology of pumps and cooling of construction equipment will be dealt with. We have actively used computational fluid dynamics in the performance analysis of pump models and the design of new models of various industrial pumps or marine pumps. And a cooling analysis system composed of 3D flow analysis and 1D cooling analysis has been established, and applied to the design of cooling systems of new models of excavators and wheel loaders. The above mentioned technology is presented in details, and some future works are mentioned

Recent Advances in Precision Machinery and Manufacturing Technology

DEFF Research Database (Denmark)

Liu, Chien-Hung; Hsieh, Wen-Hsiang; Chang, Zong-Yu

2014-01-01

Precision machinery and manufacturing technology are be- coming more important in current and future technologies. New knowledge in this field will aid in the advancement of various technologies that are needed to gain industrial competitiveness. To this end, the special issue aims to disseminate...... the latest advancements of relevant fundamental and applied research works of high quality to the inter- national community. The topics of the accepted articles in the special issue include precision manufacturing pro- cesses, measurements and control, robotics and automation, machine tools, advanced...

A Novel Fault Diagnosis Method for Rotating Machinery Based on a Convolutional Neural Network.

Science.gov (United States)

Guo, Sheng; Yang, Tao; Gao, Wei; Zhang, Chen

2018-05-04

Fault diagnosis is critical to ensure the safety and reliable operation of rotating machinery. Most methods used in fault diagnosis of rotating machinery extract a few feature values from vibration signals for fault diagnosis, which is a dimensionality reduction from the original signal and may omit some important fault messages in the original signal. Thus, a novel diagnosis method is proposed involving the use of a convolutional neural network (CNN) to directly classify the continuous wavelet transform scalogram (CWTS), which is a time-frequency domain transform of the original signal and can contain most of the information of the vibration signals. In this method, CWTS is formed by discomposing vibration signals of rotating machinery in different scales using wavelet transform. Then the CNN is trained to diagnose faults, with CWTS as the input. A series of experiments is conducted on the rotor experiment platform using this method. The results indicate that the proposed method can diagnose the faults accurately. To verify the universality of this method, the trained CNN was also used to perform fault diagnosis for another piece of rotor equipment, and a good result was achieved.

Reuse of drinking water treatment sludge for olive oil mill wastewater treatment.

Science.gov (United States)

Fragoso, R A; Duarte, E A

2012-01-01

Olive mill wastewater (OMW) results from the production of olive oil, which is an important traditional agro-industry in Mediterranean countries. In continuous three-phase centrifugation 1.0-1.2 m(3) of OMW are produced per ton of processed olives. Discharge of OMW is of serious environmental concern due to its high content of organic matter with phytotoxic properties, namely phenolic compounds. Meanwhile, drinking water treatment sludge (DWTS) is produced in high amounts and has long been considered as a waste for landfill. The aim of this work was the assessment of reusing DWTS for OMW treatment. High performance liquid chromatography (HPLC) analysis was carried out to determine the phenolic compounds present and to evaluate if they are recalcitrant. Treatability assays were performed using a dosage of DWTS from 50 to 300 g L(-1). Treatment efficiency was evaluated based on the removal of chemical oxygen demand (COD), biochemical oxygen demand (BOD), total solids (TS), total suspended solids (TSS), total volatile solids (TVS), oil and grease (OG), phenols (total phosphorous (TP) and HPLC fraction). Results from OMW HPLC characterization identified a total of 13 compounds; the major ones were hydroxytyrosol, tyrosol, caffeic acid, p-cumaric acid and oleuropein. Treatability assays led to a maximum reduction of about 90% of some of the phenolic compounds determined by HPLC. Addition of 200-300 g L(-1) of DWTS reduced 40-50% of COD, 45-50% of TP, a maximum of nearly 70% TSS and 45% for TS and TVS. The OG fraction showed a reduction of about 90%, achieved adding 300 g L(-1) od DWTS. This study points out the possibility of establishing an integrated management of OMW and DWTS, contributing to a decrease in the environmental impact of two industrial activities, olive oil production and drinking water treatment.

Outer membrane targeting of Pseudomonas aeruginosa proteins shows variable dependence on the components of Bam and Lol machineries.

Science.gov (United States)

Hoang, Hanh H; Nickerson, Nicholas N; Lee, Vincent T; Kazimirova, Anastasia; Chami, Mohamed; Pugsley, Anthony P; Lory, Stephen

2011-01-01

In Gram-negative bacteria, the Lol and Bam machineries direct the targeting of lipidated and nonlipidated proteins, respectively, to the outer membrane (OM). Using Pseudomonas aeruginosa strains with depleted levels of specific Bam and Lol proteins, we demonstrated a variable dependence of different OM proteins on these targeting pathways. Reduction in the level of BamA significantly affected the ability of the β-barrel membrane protein OprF to localize to the OM, while the targeting of three secretins that are functionally related OM proteins was less affected (PilQ and PscC) or not at all affected (XcpQ). Depletion of LolB affected all lipoproteins examined and had a variable effect on the nonlipidated proteins. While the levels of OprF, PilQ, and PscC were significantly reduced by LolB depletion, XcpQ was unaffected and was correctly localized to the OM. These results suggest that certain β-barrel proteins such as OprF primarily utilize the complete Bam machinery. The Lol machinery participates in the OM targeting of secretins to variable degrees, likely through its involvement in the assembly of lipidated Bam components. XcpQ, but not PilQ or PscC, was shown to assemble spontaneously into liposomes as multimers. This work raises the possibility that there is a gradient of utilization of Bam and Lol insertion and targeting machineries. Structural features of individual proteins, including their β-barrel content, may determine the propensity of these proteins for folding (or misfolding) during periplasmic transit and OM insertion, thereby influencing the extent of utilization of the Bam targeting machinery, respectively. Targeting of lipidated and nonlipidated proteins to the outer membrane (OM) compartment in Gram-negative bacteria involves the transfer across the periplasm utilizing the Lol and Bam machineries, respectively. We show that depletion of Bam and Lol components in Pseudomonas aeruginosa does not lead to a general OM protein translocation defect

29 CFR 1918.98 - Qualifications of machinery operators and supervisory training.

Science.gov (United States)

2010-07-01

...) Qualification of machinery operators. (1) Only an employee determined by the employer to be competent by reason...). Therefore, employers who act in accordance with the employment provisions (Title I) of the ADA (42 U.S.C... authority; elements of accidents prevention; attitudes, leadership and motivation; hazards of longshoring...

40 CFR 428.33 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Science.gov (United States)

2010-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS RUBBER MANUFACTURING POINT SOURCE CATEGORY Solution Crumb...) English units (lb/1,000 lb of product) COD 3.12 2.08 BOD5 0.12 .08 TSS 0.24 .16 Oil and grease 0.12 .08 pH...

Dedicated monitoring and machinery protection systems on reciprocating compressors

Energy Technology Data Exchange (ETDEWEB)

Grande, Alvaro; Wenisch, Markus [Hoerbiger Ventilwerke GmbH and Co KG, Wien (Austria); Jacobs, Denis [HOERBIGER do Brasil Industria de Equipamentos, Cajamar, SP (Brazil)

2012-07-01

Growing demands on reciprocating compressors (recips) in the process gas industry require particular solutions for machinery protection and performance monitoring systems. Compared to rotating equipment, monitoring systems for recips have to consider the special mechanical and physical characteristics, such as oscillating masses, variable vibration behaviour and varying operating conditions. Furthermore, they provide valuable information about the performance of cylinder related components allowing the operator the optimization of efficiency and availability, and therefore increase production. (author)

New formulations of sunflower based bio-lubricants with high oleic acid content – VOSOLUB project

Directory of Open Access Journals (Sweden)

Leao J. D.

2016-09-01

Full Text Available VOSOLUB project is a demonstration project supported by Executive Agency for Small and Medium-sized Enterprises (EASME that aims at testing under real operating conditions new formulations of sunflower-based biolubricants with high oleic acid content. These biolubricant formulations (including hydraulic fluids, greases, and neat oil metal-working fluids will be tested in three European demonstrating sites. Their technical performance will be evaluated and compared to corresponding mineral lubricants ones. In order to cover the demand for the sunflower base oil, a European SMEs network will be established to ensure the supply of the base at a competitive market price. Results presented concerns the base oil quality confirmed to be in accordance with the specification required, in particular on Free Fatty acid content, Phosphorus content, rancimat induction time and oleic acid content (ITERG. The oil characteristics specific for lubricant application analyzed by BfB Oil Research under normalized methods, match with lubricant specifications requirement such as viscosity, cold & hot properties, surface properties, anti-oxidant properties and thermal stability, anti-wear and EP properties, anti-corrosion properties Performance of the new biolubricant have been assessed by formulators and TEKNIKER First results on the use of new lubricant on real condition for rail Grease (produced by RS CLARE and tested with Sheffield Supertram, Hydraulic oil (produced by BRUGAROLAS and cutting oil (produced by MOTUL TECH and tested with innovative machining, turning are described.

Chemical oxidation of carwash industry wastewater as an effort to decrease water pollution

Science.gov (United States)

Bhatti, Zulfiqar Ahmad; Mahmood, Qaisar; Raja, Iftikhar Ahmad; Malik, Amir Haider; Khan, Muhammad Suleman; Wu, Donglei

Car wash wastewater (CWW) contains petroleum, hydrofluoric acid, ammonium bifluoride products, paint residues, rubber, phosphates, oil, grease and volatile organic compounds (VOCs). The present study dealt with various investigations conducted for the treatment of CWW. A treatment system of 5 L capacity was designed in the laboratory. Due to high load of oil and grease, CWW was aerated and scum was removed. Alum was used as coagulant in primary treatment which resulted 93% and 97% reduction in COD and turbidity. During secondary treatment CWW was further treated with waste hydrogen peroxide which resulted in further 71% and 83% reduction in COD and turbidity, respectively. Other desirable changes were also observed in pH, total dissolved solids (TDS), conductivity and dissolved oxygen contents. It was concluded that designed system could be effectively used to treat carwash wastewater that could be reused in the same station.

Flat friction tests applied to austenic stainless steels with several surface finish. Analysis of adhesion conditions in friction

International Nuclear Information System (INIS)

Coello, J.; Miguel, V.; Ferrer, C.; Calatatyd, A.; Martinez, A.

2008-01-01

The main purpose of this work is to evaluate the tribological behaviour of austenic stainless steels AISI 304 with bright surface finishing (B). The assays have been carried out in flat faced dies system with mineral oil of 200 cts viscosity, S 2 Mo grease and in dry conditions. The relationship between friction coefficient and pressure and velocity has been established for the mineral oil as lubricant. In these conditions, a strong adhesive tendency has been found in boundary lubrication regime. The results obtained here, show us that S 2 Mo grease leads to lowest values for the friction coefficient. A minor adhesive behaviour tendency for AISI 316 steel, harder than 304 grades, has been found. A relevant plowing phenomena has been observed for the more critical friction conditions tried out. A surface hardener is produced as a consequence of that. (Author) 19 refs

Abrasive Wear of Alloyed Cast Steels Applied for Heavy Machinery

Directory of Open Access Journals (Sweden)

Studnicki A.

2015-03-01

Full Text Available In the paper the results and analysis of abrasive wear studies were shown for two grades of cast steels: low-alloyed cast steel applied for heavy machinery parts such as housing, covers etc. and chromium cast steels applied for kinetic nodes of pin-sleeve type. Studies were performed using the modified in Department of Foundry pin-on-disc method.

Acute, subchronic, and developmental toxicological properties of lubricating oil base stocks.

Science.gov (United States)

Dalbey, Walden E; McKee, Richard H; Goyak, Katy Olsavsky; Biles, Robert W; Murray, Jay; White, Russell

2014-01-01

Lubricating oil base stocks (LOBs) are substances used in the manufacture of finished lubricants and greases. They are produced from residue remaining after atmospheric distillation of crude oil that is subsequently fractionated by vacuum distillation and additional refining steps. Initial LOB streams that have been produced by vacuum distillation but not further refined may contain polycyclic aromatic compounds (PACs) and may present carcinogenic hazards. In modern refineries, LOBs are further refined by multistep processes including solvent extraction and/or hydrogen treatment to reduce the levels of PACs and other undesirable constituents. Thus, mildly (insufficiently) refined LOBs are potentially more hazardous than more severely (sufficiently) refined LOBs. This article discusses the evaluation of LOBs using statistical models based on content of PACs; these models indicate that insufficiently refined LOBs (potentially carcinogenic LOBs) can also produce systemic and developmental effects with repeated dermal exposure. Experimental data were also obtained in ten 13-week dermal studies in rats, eight 4-week dermal studies in rabbits, and seven dermal developmental toxicity studies with sufficiently refined LOBs (noncarcinogenic and commonly marketed) in which no observed adverse effect levels for systemic toxicity and developmental toxicity were 1000 to 2000 mg/kg/d with dermal exposures, typically the highest dose tested. Results in both oral and inhalation developmental toxicity studies were similar. This absence of toxicologically relevant findings was consistent with lower PAC content of sufficiently refined LOBs. Based on data on reproductive organs with repeated dosing and parameters in developmental toxicity studies, sufficiently refined LOBs are likely to have little, if any, effect on reproductive parameters.

Characterization of Wastewaters obtained from Hatay Tanneries

Directory of Open Access Journals (Sweden)

Şana Sungur

2017-06-01

Full Text Available The leather tanning industry is one of the most significant pollutants in terms of both conventional and toxic parameters. On the other hand, leather industry has an important economic role both in Turkey and in the World. In this study, wastewater samples were taken from 15 different tanneries in the Hatay Region. Wastewaters obtained from liming process and chromium tanning process was analyzed. Sulfide, chromium (III, chromium (VI, oil and grease, total suspended solids (TSS, organic matters, biochemical oxygen demand (BOD, chemical oxygen demand (COD, pH and alkalinity were determined according to Turkish Standard Methods. The determined averages values belong to wastewaters obtained from liming process were as following: pH 11.71; COD 16821 mg L-1; BOD 4357 mg L-1; TSS 39023 mg L-1; oil and grease 364 mg L-1; S-2 concentration 802 mg L-1; alkalinity 2115 mg L-1. The determined averages values belong to wastewaters obtained from chromium tanning process were also as following: pH 4.23; COD 6740 mg L-1; BOD 377 mg L-1; Cr+3 concentrations 372 mg L-1; Cr+6 concentrations 127 mg L-1; TSS 14553 mg L-1; oil and grease 343 mg L-1. The results of all analyzes were higher than wastewater discharge standards. As a result, it’s necessary to use more effective treatments in order to reduce the negative impacts of leather tanning industry that affect environment, natural water resources and at last human health and welfare.

pH-Sensitive self-propelled motion of oil droplets in the presence of cationic surfactants containing hydrolyzable ester linkages.

Science.gov (United States)

Banno, Taisuke; Kuroha, Rie; Toyota, Taro

2012-01-17

Self-propelled oil droplets in a nonequilibrium system have drawn much attention as both a primitive type of inanimate chemical machinery and a dynamic model of the origin of life. Here, to create the pH-sensitive self-propelled motion of oil droplets, we synthesized cationic surfactants containing hydrolyzable ester linkages. We found that n-heptyloxybenzaldehyde oil droplets were self-propelled in the presence of ester-containing cationic surfactant. In basic solution prepared with sodium hydroxide, oil droplets moved as molecular aggregates formed on their surface. Moreover, the self-propelled motion in the presence of the hydrolyzable cationic surfactant lasted longer than that in the presence of nonhydrolyzable cationic surfactant. This is probably due to the production of a fatty acid by the hydrolysis of the ester-containing cationic surfactant and the subsequent neutralization of the fatty acid with sodium hydroxide. A complex surfactant was formed in the aqueous solution because of the cation and anion combination. Because such complex formation can induce both a decrease in the interfacial tension of the oil droplet and self-assembly with n-heptyloxybenzaldehyde and lauric acid in the aqueous dispersion, the prolonged movement of the oil droplet may be explained by the increase in heterogeneity of the interfacial tension of the oil droplet triggered by the hydrolysis of the ester-containing surfactant. © 2011 American Chemical Society

Enhanced treatment of waste frying oil in an activated sludge system by addition of crude rhamnolipid solution.

Science.gov (United States)

Zhang, Hongzi; Xiang, Hai; Zhang, Guoliang; Cao, Xia; Meng, Qing

2009-08-15

The presence of high-strength oil and grease (O&G) in wastewater poses serious challenges for environment. Addition of surfactant into the activated sludge bioreactor is feasible in reducing high concentrations of O&G via enhancing its bioavailability. In this paper, an aqueous biosurfactant solution of rhamnolipid as a cell-free culture broth of Pseudomonas aeruginosa zju.um1 was added into a batch of aerobic activated sludge system for treatment of the waste frying oil. This treatment was conducted on both bench and pilot-scales, whereas the removal efficiency of frying oil was determined by analyzing the residue concentration of O&G and chemical oxygen demand (COD). In the presence of varying concentrations of rhamnolipid from 22.5 mg/L to 90 mg/L, aerobic treatment for 30 h was enough to remove over 93% of O&G while this biodegradability was only 10% in the control system with the absence of rhamnolipids. The equivalent biodegradability was similarly obtained on COD under addition of rhamnolipid. Compared with bench studies, a higher treatment efficiency with the presence of rhamnolipids was achieved on a pilot-scale of activated sludge system, in which a short time of 12h was required for removing approximately 95% of O&G while the control treatment attained a low efficiency of 17%. Finally, foaming and biodegradability of rhamnolipids in activated sludge system were further examined in the whole treatment process. It seems that the addition of rhamnolipid-containing culture broth showed great potential for treatment of oily wastewater by activated sludge.

Enhanced treatment of waste frying oil in an activated sludge system by addition of crude rhamnolipid solution

International Nuclear Information System (INIS)

Zhang Hongzi; Xiang Hai; Zhang Guoliang; Cao Xia; Meng Qing

2009-01-01

The presence of high-strength oil and grease (O and G) in wastewater poses serious challenges for environment. Addition of surfactant into the activated sludge bioreactor is feasible in reducing high concentrations of O and G via enhancing its bioavailability. In this paper, an aqueous biosurfactant solution of rhamnolipid as a cell-free culture broth of Pseudomonas aeruginosa zju.um1 was added into a batch of aerobic activated sludge system for treatment of the waste frying oil. This treatment was conducted on both bench and pilot-scales, whereas the removal efficiency of frying oil was determined by analyzing the residue concentration of O and G and chemical oxygen demand (COD). In the presence of varying concentrations of rhamnolipid from 22.5 mg/L to 90 mg/L, aerobic treatment for 30 h was enough to remove over 93% of O and G while this biodegradability was only 10% in the control system with the absence of rhamnolipids. The equivalent biodegradability was similarly obtained on COD under addition of rhamnolipid. Compared with bench studies, a higher treatment efficiency with the presence of rhamnolipids was achieved on a pilot-scale of activated sludge system, in which a short time of 12 h was required for removing approximately 95% of O and G while the control treatment attained a low efficiency of 17%. Finally, foaming and biodegradability of rhamnolipids in activated sludge system were further examined in the whole treatment process. It seems that the addition of rhamnolipid-containing culture broth showed great potential for treatment of oily wastewater by activated sludge.

Agricultural and oil commodities: price transmission and market integration between US and Italy

Directory of Open Access Journals (Sweden)

Franco Rosa

2014-08-01

Full Text Available Purpose of this article it to get some evidences of market interaction between United States and Italy using the time series analysis of spot prices spanning from January 1999 to May 2012 for crude oil and three ag-commodities: wheat, corn and soybean. These crops have been selected for their relevance in ag-commodity exchanges between US and Italy markets. The integration between US and Italy agricultural markets is hypothesized for the consistent volume of crop traded between these two countries while the price transmission is related to the leading price signals of the CBT (Chicago Board of Trade. The integration between oil and ag-commodity markets is suggested both by the large use of energy intensive inputs, (fertilizer, seed, machinery in production of these ag-commodities, and their use in biofuel production. The results suggest: a for US market the evidence of market integration between crude oil and US ag-commodities; b for Italy the integration with US ag-commodity markets and less evidence of integration with the oil market. These results are valuable information both for the agents and policy makers contributing to improve the information accuracy to predict the price movements used by marketing operators for their strategies and policy makers to set up policies to re-establish conditions of market efficiency and allocate these ag-commodities in alternative market channels.

MODELING ENVIRONMENTAL IMPACT OF MACHINERY SECTORS TO PROMOTE SUSTAINABLE DEVELOPMENT OF THAILAND

Directory of Open Access Journals (Sweden)

Pruethsan Sutthichaimethee

2016-01-01

Full Text Available The objective of this research is to propose an indicator to evaluate environmental impacts from the machinery sectors of Thailand, leading to more sustainable consumption and production in this sector of the economy. The factors used to calculate the forward linkage, backward linkage and real benefit included the total environmental costs. The highest total environmental cost was railway equipment need to be resolved immediately because it uses natural resources in carrying capacity, higher than standard environmental cost, and contribute to low real benefit. Electric accumulator & battery, secondary special industrial machinery, motorcycle, bicycle & other carriages, and engines and turbines need to monitor closely because they are able to link to other production sectors more than other production sector do and they have high environmental cost. In order to decide the sustainable development strategy of the country, there is a need to use this research to support decision-making.

Download this PDF file

African Journals Online (AJOL)

userpc

drained into sewage system, industrial waterborne wastes such as oils, grease, animal and vegetable matter discharged by factories and ground, surface and atmospheric waters that enters the sewage system (Tortoraet al.,. 2010). Domestic wastewater mostly contains waste from home, kitchen and bathroom and consists.

40 CFR Appendix G to Subpart A of... - UNEP Recommendations for Conditions Applied to Exemption for Essential Laboratory and Analytical...

Science.gov (United States)

2010-07-01

... calibration; use as extraction solvents, diluents, or carriers for chemical analysis; biochemical research; inert solvents for chemical reactions, as a carrier or laboratory chemical and other critical analytical... global laboratory exemption: a. Testing of oil and grease and total petroleum hydrocarbons in water; b...

Development and implementation of a propeller test capability for GL-10 "Greased Lightning" propeller design

Science.gov (United States)

Duvall, Brian Edward

Interest in small unmanned aerial vehicles has increased dramatically in recent years. Hybrid vehicles which allow forward flight as a fixed wing aircraft and a true vertical landing capability have always had applications. Management of the available energy and noise associated with electric propeller propulsion systems presents many challenges. NASA Langley has developed the Greased Lightning 10 (GL-10) vertical takeoff, unmanned aerial vehicle with ten individual motors and propellers. All are used for propulsion during takeoff and contribute to acoustic noise pollution which is an identified nuisance to the surrounding users. A propeller test capability was developed to gain an understanding of how the noise can be reduced while meeting minimum thrust requirements. The designed propeller test stand allowed for various commercially available propellers to be tested for potential direct replacement of the current GL-10 propellers and also supported testing of a newly designed propeller provided by the Georgia Institute of Technology. Results from the test program provided insight as to which factors affect the noise as well as performance characteristics. The outcome of the research effort showed that the current GL-10 propeller still represents the best choice of all the candidate propellers tested.

Identification and analysis of the RNA degrading complexes and machinery of Giardia lamblia using an in silico approach.

Science.gov (United States)

Williams, Christopher W; Elmendorf, Heidi G

2011-11-29

RNA degradation is critical to the survival of all cells. With increasing evidence for pervasive transcription in cells, RNA degradation has gained recognition as a means of regulating gene expression. Yet, RNA degradation machinery has been studied extensively in only a few eukaryotic organisms, including Saccharomyces cerevisiae and humans. Giardia lamblia is a parasitic protist with unusual genomic traits: it is binucleated and tetraploid, has a very compact genome, displays a theme of genomic minimalism with cellular machinery commonly comprised of a reduced number of protein components, and has a remarkably large population of long, stable, noncoding, antisense RNAs. Here we use in silico approaches to investigate the major RNA degradation machinery in Giardia lamblia and compare it to a broad array of other parasitic protists. We have found key constituents of the deadenylation and decapping machinery and of the 5'-3' RNA degradation pathway. We have similarly found that all of the major 3'-5' RNA degradation pathways are present in Giardia, including both exosome-dependent and exosome-independent machinery. However, we observe significant loss of RNA degradation machinery genes that will result in important differences in the protein composition, and potentially functionality, of the various RNA degradation pathways. This is most apparent in the exosome, the central mediator of 3'-5' degradation, which apparently contains an altered core configuration in both Giardia and Plasmodium, with only four, instead of the canonical six, distinct subunits. Additionally the exosome in Giardia is missing both the Rrp6, Nab3, and Nrd1 proteins, known to be key regulators of noncoding transcript stability in other cells. These findings suggest that although the full complement of the major RNA degradation mechanisms were present - and likely functional - early in eukaryotic evolution, the composition and function of the complexes is more variable than previously

Assessment of exposure to manganese in welding operations during the assembly of heavy excavation machinery accessories.

Science.gov (United States)

Smargiassi, A; Baldwin, M; Savard, S; Kennedy, G; Mergler, D; Zayed, J

2000-10-01

Welder exposure to metals in various industrial sectors is poorly characterized. We had the opportunity to carry out an exploratory study to characterize manganese exposure in welding operations in a recently established Quebec factory that assembled accessories for heavy excavation machinery. Ten workers were sampled for total manganese for at least two consecutive days out of three followed by two consecutive days for respirable manganese (with a size selective sampler with a median cut-off of 4 microns), during a typical week in the summer of 1998. Parts being welded were characterized as large or small. Small parts were those being welded on tables during subassembly. Workers were divided into two groups according to the parts they were welding. Seventy-eight percent of the total manganese exposure levels of welding operations during the assembly of large accessories of heavy excavation machinery exceeded the manganese American Conference of Governmental Industrial Hygienists (ACGIH) threshold limit value (TLV) of 0.20 mg/m3 (GM 0.24 mg/m3, n = 14) while none exceeded the TLV during the assembly of small pieces (GM 0.06 mg/m3, n = 8). Welding operations during the assembly of large heavy excavation machinery accessories may pose a significant health hazard. Considering the importance of task-related variables affecting exposure among workers, further studies are needed to better characterize exposure determinants of welding operations during the assembly of heavy excavation machinery accessories.

Bioremediation of hydrocarbon-contaminated soils: are treatability and ecotoxicity endpoints related?

International Nuclear Information System (INIS)

Visser, S.

1999-01-01

To determine if there is a relationship between biotreatability and ecotoxicity endpoints in a wide range of hydrocarbon-contaminated soils, including medium and heavy crude oil-contaminated flare pit wastes and lubrication oil contaminated soil, research was conducted. Each test material was analyzed for pH, water repellency, electrical conductivity, available N and P, total extractable hydrocarbons, oil and grease, and toxicity to seedling emergence, root elongation in barley, lettuce and canola, earthworm survival and luminescent bacteria (Microtox), prior to, and following three months of bioremediation in the laboratory. By monitoring soil respiration, progress of the bioremediation process and determination of a treatment endpoint were assessed. The time required to attain a treatment endpoint under laboratory conditions can range from 30 days to 100 days depending on the concentration of hydrocarbons and degree of weathering. Most flare pits are biotreatable, averaging a loss of 25-30% of hydrocarbons during bioremediation. Once a treatment endpoint is achieved, residual hydrocarbons contents almost always exceeds Alberta Tier I criteria for mineral oil and grease. As a result of bioremediation treatments, hydrophobicity is often reduced from severe to low. Many flare pit materials are still moderately to extremely toxic after reaching a treatment endpoint. (Abstract only)

Monitoring of vibrating machinery using artificial neural networks

International Nuclear Information System (INIS)

Alguindigue, I.E.; Loskiewicz-Buczak, A.

1991-01-01

The primary source of vibration in complex engineering systems is rotating machinery. Vibration signatures collected from these components render valuable information about the operational state of the system and may be used to perform diagnostics. For example, the low frequency domain contains information about unbalance, misalignment, instability in journal bearing and mechanical looseness; analysis of the medium frequency range can render information about faults in meshing gear teeth; while the high frequency domain will contain information about incipient faults in rolling-element bearings. Trend analysis may be performed by comparing the vibration spectrum for each machine with a reference spectrum and evaluating the vibration magnitude changes at different frequencies. This form of analysis for diagnostics is often performed by maintenance personnel monitoring and recording transducer signals and analyzing the signals to identify the operating condition of the machine. With the advent of portable fast Fourier transform (FFT) analyzers and ''laptop'' computers, it is possible to collect and analyze vibration data an site and detect incipient failures several weeks or months before repair is necessary. It is often possible to estimate the remaining life of certain systems once a fault has been detected. RMS velocity, acceleration, displacements, peak value, and crest factor readings can be collected from vibration sensors. To exploit all the information embedded in these signals, a robust and advanced analysis technique is required. Our goal is to design a diagnostic system using neural network technology, a system such as this would automate the interpretation of vibration data coming from plant-wide machinery and permit efficient on-line monitoring of these components

Conceptual design and analysis of roads and road construction machinery for initial lunar base operations

Science.gov (United States)

Sines, Jeffrey L.; Banks, Joel; Efatpenah, Keyanoush

1990-01-01

Recent developments have made it possible for scientists and engineers to consider returning to the Moon to build a manned lunar base. The base can be used to conduct scientific research, develop new space technology, and utilize the natural resources of the Moon. Areas of the base will be separated, connected by a system of roads that reduce the power requirements of vehicles traveling on them. Feasible road types for the lunar surface were analyzed and a road construction system was designed for initial lunar base operations. A model was also constructed to show the system configuration and key operating features. The alternate designs for the lunar road construction system were developed in four stages: analyze and select a road type; determine operations and machinery needed to produce the road; develop machinery configurations; and develop alternates for several machine components. A compacted lunar soil road was selected for initial lunar base operations. The only machinery required to produce this road were a grader and a compactor. The road construction system consists of a main drive unit which is used for propulsion, a detachable grader assembly, and a towed compactor.

The Antioxidant Machinery of Young and Senescent Human Umbilical Vein Endothelial Cells and Their Microvesicles

Directory of Open Access Journals (Sweden)

Guillermo Bodega

2017-01-01

Full Text Available We examine the antioxidant role of young and senescent human umbilical vein endothelial cells (HUVECs and their microvesicles (MVs. Proteomic and Western blot studies have shown young HUVECs to have a complete and well-developed antioxidant system. Their MVs also contain antioxidant molecules, though of a smaller and more specific range, specialized in the degradation of hydrogen peroxide and the superoxide anion via the thioredoxin-peroxiredoxin system. Senescence was shown to be associated with a large increase in the size of the antioxidant machinery in both HUVECs and their MVs. These responses might help HUVECs and their MVs deal with the more oxidising conditions found in older cells. Functional analysis confirmed the antioxidant machinery of the MVs to be active and to increase in size with senescence. No glutathione or nonpeptide antioxidant (ascorbic acid and vitamin E activity was detected in the MVs. Endothelial cells and MVs seem to adapt to higher ROS concentrations in senescence by increasing their antioxidant machinery, although this is not enough to recover completely from the senescence-induced ROS increase. Moreover, MVs could be involved in the regulation of the blood plasma redox status by functioning as ROS scavengers.

A sequential fuzzy diagnosis method for rotating machinery using ant colony optimization and possibility theory

Energy Technology Data Exchange (ETDEWEB)

Sun, Hao; Ping, Xueliang; Cao, Yi; Lie, Ke [Jiangnan University, Wuxi (China); Chen, Peng [Mie University, Mie (Japan); Wang, Huaqing [Beijing University, Beijing (China)

2014-04-15

This study proposes a novel intelligent fault diagnosis method for rotating machinery using ant colony optimization (ACO) and possibility theory. The non-dimensional symptom parameters (NSPs) in the frequency domain are defined to reflect the features of the vibration signals measured in each state. A sensitive evaluation method for selecting good symptom parameters using principal component analysis (PCA) is proposed for detecting and distinguishing faults in rotating machinery. By using ACO clustering algorithm, the synthesizing symptom parameters (SSP) for condition diagnosis are obtained. A fuzzy diagnosis method using sequential inference and possibility theory is also proposed, by which the conditions of the machinery can be identified sequentially. Lastly, the proposed method is compared with a conventional neural networks (NN) method. Practical examples of diagnosis for a V-belt driving equipment used in a centrifugal fan are provided to verify the effectiveness of the proposed method. The results verify that the faults that often occur in V-belt driving equipment, such as a pulley defect state, a belt defect state and a belt looseness state, are effectively identified by the proposed method, while these faults are difficult to detect using conventional NN.

Industrial policy and technology diffusion : evidence from paper making machinery in Indonesia

NARCIS (Netherlands)

Dijk, van M.; Szirmai, A.

2006-01-01

In this paper, we analyze the diffusion and adoption of paper making machinery in the Indonesian pulp and paper industry, from 1923 till 2000. We develop a machine level index of technological sophistication (mach), which measures the technological distance of each paper machine to the world

Response of Anopheles gambiae detoxification enzymes to levels of ...

African Journals Online (AJOL)

Some of the sampled larvae were reared to pupae and adult life stages. Levels of 7 physical (pH, temperature, conductivity, transparency, total dissolved solids, dissolved oxygen and biological oxygen demand) and 6 chemical (sulphates, phosphates, nitrites, nitrates, carbon content and oil and grease) environmental ...

Evaluation of some industrial effluents in Jos metropolis, Plateau ...

African Journals Online (AJOL)

P.TECHNOLOGY

Standards and Regulations Enforcement Agency (NESREA) limits for pH, chloride, oil and grease, zinc, ... completely treated or in its natural stage into the ... the highest purity and analytical grade of individual elements. Other ... and sulphide were all determined using Standard Methods for the ..... Drugs and Diseases.

Attenuated Total Reflectance Fourier transform infrared spectroscopy for determination of long chain free fatty acid concentration in oily wastewater using the double wavenumber extrapolation technique

Science.gov (United States)

Long Chain Free Fatty Acids (LCFFAs) from the hydrolysis of fat, oil and grease (FOG) are major components in the formation of insoluble saponified solids known as FOG deposits that accumulate in sewer pipes and lead to sanitary sewer overflows (SSOs). A Double Wavenumber Extrapolative Technique (DW...

New Fault Recognition Method for Rotary Machinery Based on Information Entropy and a Probabilistic Neural Network.

Science.gov (United States)

Jiang, Quansheng; Shen, Yehu; Li, Hua; Xu, Fengyu

2018-01-24

Feature recognition and fault diagnosis plays an important role in equipment safety and stable operation of rotating machinery. In order to cope with the complexity problem of the vibration signal of rotating machinery, a feature fusion model based on information entropy and probabilistic neural network is proposed in this paper. The new method first uses information entropy theory to extract three kinds of characteristics entropy in vibration signals, namely, singular spectrum entropy, power spectrum entropy, and approximate entropy. Then the feature fusion model is constructed to classify and diagnose the fault signals. The proposed approach can combine comprehensive information from different aspects and is more sensitive to the fault features. The experimental results on simulated fault signals verified better performances of our proposed approach. In real two-span rotor data, the fault detection accuracy of the new method is more than 10% higher compared with the methods using three kinds of information entropy separately. The new approach is proved to be an effective fault recognition method for rotating machinery.

A Diagnosis Method for Rotation Machinery Faults Based on Dimensionless Indexes Combined with K-Nearest Neighbor Algorithm

Directory of Open Access Journals (Sweden)

Jianbin Xiong

2015-01-01

Full Text Available It is difficult to well distinguish the dimensionless indexes between normal petrochemical rotating machinery equipment and those with complex faults. When the conflict of evidence is too big, it will result in uncertainty of diagnosis. This paper presents a diagnosis method for rotation machinery fault based on dimensionless indexes combined with K-nearest neighbor (KNN algorithm. This method uses a KNN algorithm and an evidence fusion theoretical formula to process fuzzy data, incomplete data, and accurate data. This method can transfer the signals from the petrochemical rotating machinery sensors to the reliability manners using dimensionless indexes and KNN algorithm. The input information is further integrated by an evidence synthesis formula to get the final data. The type of fault will be decided based on these data. The experimental results show that the proposed method can integrate data to provide a more reliable and reasonable result, thereby reducing the decision risk.

Disparate peroxisome-related defects in Arabidopsis pex6 and pex26 mutants link peroxisomal retrotranslocation and oil body utilization.

Science.gov (United States)

Gonzalez, Kim L; Fleming, Wendell A; Kao, Yun-Ting; Wright, Zachary J; Venkova, Savina V; Ventura, Meredith J; Bartel, Bonnie

2017-10-01

Catabolism of fatty acids stored in oil bodies is essential for seed germination and seedling development in Arabidopsis. This fatty acid breakdown occurs in peroxisomes, organelles that sequester oxidative reactions. Import of peroxisomal enzymes is facilitated by peroxins including PEX5, a receptor that delivers cargo proteins from the cytosol to the peroxisomal matrix. After cargo delivery, a complex of the PEX1 and PEX6 ATPases and the PEX26 tail-anchored membrane protein removes ubiquitinated PEX5 from the peroxisomal membrane. We identified Arabidopsis pex6 and pex26 mutants by screening for inefficient seedling β-oxidation phenotypes. The mutants displayed distinct defects in growth, response to a peroxisomally metabolized auxin precursor, and peroxisomal protein import. The low PEX5 levels in these mutants were increased by treatment with a proteasome inhibitor or by combining pex26 with peroxisome-associated ubiquitination machinery mutants, suggesting that ubiquitinated PEX5 is degraded by the proteasome when the function of PEX6 or PEX26 is reduced. Combining pex26 with mutations that increase PEX5 levels either worsened or improved pex26 physiological and molecular defects, depending on the introduced lesion. Moreover, elevating PEX5 levels via a 35S:PEX5 transgene exacerbated pex26 defects and ameliorated the defects of only a subset of pex6 alleles, implying that decreased PEX5 is not the sole molecular deficiency in these mutants. We found peroxisomes clustered around persisting oil bodies in pex6 and pex26 seedlings, suggesting a role for peroxisomal retrotranslocation machinery in oil body utilization. The disparate phenotypes of these pex alleles may reflect unanticipated functions of the peroxisomal ATPase complex. © 2017 The Authors The Plant Journal © 2017 John Wiley & Sons Ltd.

Industrial policy and technology diffusion : evidence from paper making machinery in Indonesia

NARCIS (Netherlands)

Dijk, van M.; Szirmai, A.

2005-01-01

In this paper, we analyse the diffusion and adoption of paper making machinery in the Indonesian pulp and paper industry, from 1923 till 2000. The two main questions in this paper are: (1) What patterns of technology diffusion can be discerned in the Indonesian paper manufacturing sector? (2) What

46 CFR 167.15-25 - Inspection standards for hulls, boilers and machinery.

Science.gov (United States)

2010-10-01

... SCHOOLS PUBLIC NAUTICAL SCHOOL SHIPS Inspections § 167.15-25 Inspection standards for hulls, boilers and... 46 Shipping 7 2010-10-01 2010-10-01 false Inspection standards for hulls, boilers and machinery... inspection. These rules may be purchased from the American Bureau of Shipping (ABS), ABS Plaza, 16855...

Model Feed for Hydrotreating of Fat for Biodiesel Production

DEFF Research Database (Denmark)

Biodiesel production by the transesterification of oils and fats with an alcohol to fatty acid alkyl esters is rapidly increasing worldwide. Plant oils are usually suited for transesterification, but feedstocks from waste products like trap greases and abattoir wastes are difficult to react due...... resulted in lower conversions and a much higher degree of hydrogenation than with the Pt catalyst. This protocol represents a facile method of studying hydrotreating of waste fats and oils for biodiesel production, which may be a viable alternative to current dominating transesterification technology. 1...

Transportation of part supply improvement in agricultural machinery assembly plant

Science.gov (United States)

Saysaman, Anusit; Chutima, Parames

2018-02-01

This research focused on the problem caused by the transportation of part supply in agricultural machinery assembly plant in Thailand, which is one of the processes that are critical to the whole production process. If poorly managed, it will affect transportation of part supply, the emergence of sink cost, quality problems, and the ability to respond to the needs of the customers in time. Since the competition in the agricultural machinery market is more intense, the efficiency of part transportation process has to be improved. In this study, the process of transporting parts of the plant was studied and it was found that the efficiency of the process of transporting parts from the sub assembly line to its main assembly line was 83%. The approach to the performance improvement is done by using the Lean tool to limit wastes based on the ECRS principle and applying pull production system by changing the transportation method to operate as milkrun for transportation of parts to synchronize with the part demands of the main assembly line. After the transportation of parts from sub-assembly line to the main assembly line was improved, the efficiency raised to 98% and transportation process cost was saved to 540,000 Baht per year.

Experiences with fuels B30 and B 100 in haulage, railway operation and agricultural machinery

Energy Technology Data Exchange (ETDEWEB)

Matejovsky, V. [QMS Consulting, Prague (Czech Republic); Hendrych, K.; Mares, V. [PREOL, Lovosice (Czech Republic)

2013-06-01

High prices of diesel fuel have increased an interest in cheaper biodiesel, especially for vehicles with high fuel consumption and not only for haulage vehicle parks but also for railway vehicles and heavy agricultural machinery. When price difference between standard diesel B7 and cheaper biodiesel B100 reached more than 10% it was a sufficient benefit for operators to use biodiesel but this fuel had not been approved for all vehicles types by their manufacturers. Despite this problem, some operators have begun to use biodiesel also for vehicles not having the approval. To prevent operational problems and misgiving of engines damage, the transition to alternative fuel was organized as field tests of one or more vehicles from the operator's fleet. The tests usually started with B30 fuel and if no operational problems occurred the second stage continued with B100. The tested vehicles were under permanent surveillance at least during one year of operation and once a month and later once in a quarter a deeper inspections were made including engine diagnostics, emissions testing, engine oil sampling for laboratory examination, injectors tenting and filters and fuel hoses condition evaluation. The presentation includes the results of vehicles inspections and the measures that had to be done to prevent engines failure and to ensure trouble-free operation of vehicles using biofuels. (orig.)

Assessment of the most significant causes of transportation and machinery accidents on collieries

CSIR Research Space (South Africa)

Oberholzer, JW

1995-08-01

Full Text Available The purpose of this study is to identify those areas, classified according to the SAMRASS data base system under the codes relating to underground transport and machinery type accidents that give cause to the greatest amount of accidents...

Effects of glycerin concentration in steam-flaked corn-based diets with supplemental yellow grease on performance and carcass characteristics of finishing beef steers.

Science.gov (United States)

Buttrey, E K; Luebbe, M K; McCollum, F T; Cole, N A; MacDonald, J C; Hales, K E

2015-07-01

Forty-eight individually fed crossbred steers (initial BW = 381 ± 7.61 kg) were used to determine the effects of glycerin (GLY) concentration in steam-flaked corn (SFC)-based diets with added yellow grease on animal performance and carcass characteristics. Glycerin was included at 0, 2.5, 5, and 10% dietary DM replacing SFC. A completely randomized design was used with steers as the experimental unit, and the model included the fixed effects of diet. Contrast statements were used to determine linear and quadratic effects of GLY inclusion. Final BW and DMI were not affected (P > 0.27) by GLY concentration. Average daily gain and G:F based on live BW did not differ as GLY level increased in the diet from 0 to 10% of DM (P > 0.33). Carcass-adjusted final BW and carcass-adjusted G:F were also not affected by GLY concentration (P > 0.22); however, carcass-adjusted ADG tended to respond quadratically by decreasing from 2.5 to 5% GLY inclusion and increasing thereafter (P = 0.10). Calculated dietary NEm and NEg did not differ as GLY increased in the diet (P > 0.37). Hot carcass weight tended to respond quadratically, decreasing from 2.5 to 5% GLY and increasing thereafter (P = 0.10). Likewise, dressing percentage tended to respond quadratically by decreasing from 2.5 to 5% GLY inclusion and increasing to 10% GLY inclusion (P = 0.09). Fat thickness decreased linearly as GLY inclusion increased in the diet (P 0.21). Calculated yield grade (YG) decreased linearly as GLY increased in the diet from 0 to 10% of DM (P = 0.04). Based on our results, there was no animal performance benefit for replacing SFC with GLY in diets containing yellow grease, and the only change in carcass merit was a slight improvement in YG.

The adaptive response of lichens to mercury exposure involves changes in the photosynthetic machinery

International Nuclear Information System (INIS)

Nicolardi, Valentina; Cai, Giampiero; Parrotta, Luigi; Puglia, Michele; Bianchi, Laura; Bini, Luca; Gaggi, Carlo

2012-01-01

Lichens are an excellent model to study the bioaccumulation of heavy metals but limited information is available on the molecular mechanisms occurring during bioaccumulation. We investigated the changes of the lichen proteome during exposure to constant concentrations of mercury. We found that most of changes involves proteins of the photosynthetic pathway, such as the chloroplastic photosystem I reaction center subunit II, the oxygen-evolving protein and the chloroplastic ATP synthase β-subunit. This suggests that photosynthesis is a target of the toxic effects of mercury. These findings are also supported by changes in the content of photosynthetic pigments (chlorophyll a and b, and β-carotene). Alterations to the photosynthetic machinery also reflect on the structure of thylakoid membranes of algal cells. Response of lichens to mercury also involves stress-related proteins (such as Hsp70) but not cytoskeletal proteins. Results suggest that lichens adapt to mercury exposure by changing the metabolic production of energy. - Highlights: ► Lichens exposed to Hg° vapors accumulate this metal irreversibly. ► Hg° interferes with physiological processes of the epiphytic lichen Evernia prunastri. ► Hg° promotes changes in the concentration of photosynthetic pigments. ► Hg° treatment causes changes in the ultrastructure of the photobiont plastids. ► Hg° induces changes in the protein machinery involved in the photosynthesis pathway. - Mercury affects the photosynthetic protein machinery of lichens.

What would be the effects of a carbon tax in Japan: an historic analysis of subsidies and fuel pricing on the iron & steel, chemical, and machinery industries

Directory of Open Access Journals (Sweden)

Takako Wakiyama

2016-06-01

Full Text Available This study examines how a carbon tax could affect industrial-related carbon dioxide (CO2 emissions in Japan. Rather than forecasting the effects of a tax, the paper employs a time-series autoregressive moving average (ARMA model to determine how past subsidies and fuel price changes affected investments in energy and carbon intensity in Japan’s iron & steel, chemical, and machinery industries from 1993 to 2004. The results suggest the impacts varied greatly across industries. In the iron & steel industry, subsidies and price changes produced negligible effects on investments in energy and carbon intensity. This may be because existing iron & steel technologies have long lifetimes and substantial replacement costs. It may also be because the few large companies dominating the industry were relatively immune to subsidy provisions and pricing changes. In the chemical industry, subsidies and fuel prices gave rise to investments that improved carbon and energy intensity. This may be because the industry has relatively higher operation costs that could be cut easily given financial incentives. In the machinery industry, two of three fuel price changes (oil and gas, but not subsidy provisions, yielded improvements in carbon and energy intensity. This may reflect the heterogeneity of companies and products comprising the industry. Overall, the study underscores that policymakers need to tailor the rates and revenue recycling provisions of a carbon tax to an industry’s unique features to stimulate CO2 reductions.

40 CFR 136.6 - Method modifications and analytical requirements.

Science.gov (United States)

2010-07-01

... modifications and analytical requirements. (a) Definitions of terms used in this section. (1) Analyst means the..., oil and grease, total suspended solids, total phenolics, turbidity, chemical oxygen demand, and.... Except as set forth in paragraph (b)(3) of this section, an analyst may modify an approved test procedure...

Evaluation of the effect of fat content of sunflower meal on rumen ...

African Journals Online (AJOL)

Yomi

2012-01-03

Jan 3, 2012 ... addition of yellow grease and corn oil increased in vitro rumen degradation and gas production. ... Culturing of rumen anaerobic fungi. Rumen anaerobic fungi were isolated from wheat straw residues, ... concentrate : forage diet (corn grain, barley grain and wheat bran : sugarcane silage, corn silage, alfalfa ...

40 CFR 408.31 - Specialized definitions.

Science.gov (United States)

2010-07-01

... apply to this subpart. (b) The term oil and grease shall mean those components of a waste water amenable to measurement by the method described in Methods for Chemical Analysis of Water and Wastes, 1971, Environmental Protection Agency, Analytical Quality Control Laboratory, page 217. (c) The term seafood shall...

40 CFR 408.91 - Specialized definitions.

Science.gov (United States)

2010-07-01

... apply to this subpart. (b) The term oil and grease shall mean those components of a waste water amenable to measurement by the method described in Methods for Chemical Analysis of Water and Wastes, 1971, Environmental Protection Agency, Analytical Quality Control Laboratory, page 217. (c) The term seafood shall...

40 CFR 408.51 - Specialized definitions.

Science.gov (United States)

2010-07-01

... apply to this subpart. (b) The term oil and grease shall mean those components of a waste water amenable to measurement by the method described in Methods for Chemical Analysis of Water and Wastes, 1971, Environmental Protection Agency, Analytical Quality Control Laboratory, page 217. (c) The term seafood shall...

40 CFR 408.11 - Specialized definitions.

Science.gov (United States)

2010-07-01

... apply to this subpart. (b) The term oil and grease shall mean those components of a waste water amenable to measurement by the method described in Methods for Chemical Analysis of Water and Wastes, 1971, Environmental Protection Agency, Analytical Quality Control Laboratory, page 217. (c) The term seafood shall...

40 CFR 408.21 - Specialized definitions.

Science.gov (United States)

2010-07-01

... apply to this subpart. (b) The term oil and grease shall mean those components of a waste water amenable to measurement by the method described in Methods for Chemical Analysis of Water and Wastes, 1971, Environmental Protection Agency, Analytical Quality Control Laboratory, page 217. (c) The term seafood shall...

40 CFR 408.141 - Specialized definitions.

Science.gov (United States)

2010-07-01

... apply to this subpart. (b) The term oil and grease shall mean those components of a waste water amenable to measurement by the method described in Methods for Chemical Analysis of Water and Wastes, 1971, Environmental Protection Agency, Analytical Quality Control Laboratory, page 217. (c) The term seafood shall...

Purification of biologically treated Tehran refinery oily wastewater using reverse osmosis

DEFF Research Database (Denmark)

Salahi, Abdolhamid; Mohammadi, Toraj; Fini, Mahdi Nikbakht

2012-01-01

were found to be complex. By increasing acidic and basic nature of the feed, permeation flux was found to increase but rejection decrease. At original oily wastewater composition, high rejection of TDS (87%), COD (95%), BOD5 (95%), TOC (90%), turbidity (82%) and oil and grease content (87%) along...

Corrosion inhibitors. Manufacture and technology

International Nuclear Information System (INIS)

Ranney, M.W.

1976-01-01

Detailed information is presented relating to corrosion inhibitors. Areas covered include: cooling water, boilers and water supply plants; oil well and refinery operations; fuel and lubricant additives for automotive use; hydraulic fluids and machine tool lubes; grease compositions; metal surface treatments and coatings; and general processes for corrosion inhibitors

Lubrication fundamentals

International Nuclear Information System (INIS)

Wills, J.G.

1990-01-01

This book is organized under the following headings: lubricating oils; lubricating greases; synthetic lubricants; machine elements; lubricant application; internal combustion engines; stationary gas turbines; steam turbines; hydraulic turbines; nuclear power plants; automotive chassis components; automotive power transmissions; compressors; handling, storing, and dispensing lubricants, in-plant handling for lubricant conservation

21 CFR 173.165 - Candida lipolytica.

Science.gov (United States)

2010-04-01

... may be safely used as the organism for fermentation production of citric acid in accordance with the... intended for use as a pure culture in the fermentation process for the production of citric acid from... such as oil, grease, detergent residues, etc. Examine all glassware including stoppers and stopcocks...

Lead isotope profiling in dairy calves.

Science.gov (United States)

Buchweitz, John; McClure-Brinton, Kimberly; Zyskowski, Justin; Stensen, Lauren; Lehner, Andreas

2015-03-01

Lead (Pb) is a common cause of heavy metal poisonings in cattle. Sources of Pb on farms include crankcase oil, machinery grease, batteries, plumbing, and paint chips. Consequently, consumption of Pb from these sources may negatively impact animal health and Pb may be inadvertently introduced into the food supply. Therefore, the scope of poisoning incidents must be clearly assessed and sources of intoxication identified and strategies to mitigate exposure evaluated and implemented to prevent future exposures. Stable isotope analysis by inductively-coupled plasma mass spectrometry (ICP-MS) has proven itself of value in forensic investigations. We report on the extension of Pb stable isotope analysis to bovine tissues and profile comparisons with paint chips and soils collected from an affected dairy farm to elucidate the primary source. Pb occurs naturally as four stable isotopes: (204)Pb, (206)Pb, (207)Pb, and (208)Pb. Herein a case is reported to illustrate the use of (207)Pb/(206)Pb and (208)Pb/(206)Pb ratios to link environmental sources of exposure with tissues from a poisoned animal. Chemical Pb profiling provides a valuable tool for field investigative approaches to Pb poisoning in production agriculture and is applicable to subclinical exposures. Copyright © 2014 Elsevier Inc. All rights reserved.

Ultra high-temperature solids-free insulating packer fluid for oil and gas production, steam injection and geothermal wells

Energy Technology Data Exchange (ETDEWEB)

Ezell, R.G.; Harrison, D.J. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Halliburton Energy Services, Calgary, AB (Canada)

2008-10-15

Uncontrolled heat transfer from production/injection tubing during thermal oil recovery via steam injection can be detrimental to the integrity of the casing and to the quality of the steam that is injected into the reservoir. An aqueous-based insulating packer fluid (IPF) was introduced to improve the steam injection process by controlling the total heat loss from the produced fluids to the surrounding wellbore, internal annuli and formation. The IPF was developed for elevated temperature environments through extensive investigation across multidisciplinary technology. The innovative system delivers performance beyond conventional systems of comparable thermal conductivity. Its density range and conductivity measurements were presented in this paper. High-temperature static aging tests showed superior gel integrity without any phase separation after exposure to temperatures higher than 260 degrees C. The new fluids are hydrate inhibitive, non-corrosive and pass oil and grease testing. They are considered to be environmentally sound by Gulf of Mexico standards. It was concluded that the new ultra high-performance insulating packer fluid (HTIPF) reduced the heat loss significantly by both conduction and convection. Heat transfer within the aqueous-based HTIPF was 97 per cent less than that of pure water. It was concluded that the HTIPF can be substituted for conventional packer fluids without compromising any well control issues. 21 refs., 1 tab., 4 figs.

Targeting apoptotic machinery as approach for anticancer therapy: Smac mimetics as anticancer agents

Directory of Open Access Journals (Sweden)

Nevine M.Y. Elsayed

2015-06-01

Full Text Available Apoptosis is a chief regulator of cellular homeostasis. Impairment of apoptotic machinery is a main characteristic of several diseases such as cancer, where the evasion of apoptosis is a cardinal hallmark of cancer. Apoptosis is regulated by contribution of pro- and anti- apoptotic proteins, where caspases are the main executioners of the apoptotic machinery. IAP (inhibitors of apoptosis proteins is a family of endogenous inhibitors of apoptosis, which perform their function through interference with the function of caspases. Smac (second mitochondria-derived activator of caspases is endogenous inhibitor of IAPs, thus it is one of the major proapoptotic endogenous proteins. Thus, the development of Smac mimetics has evolved as an approach for anticancer therapy. Several Smac mimetic agents have been introduced to clinical trial such as birinapanet 12. Herein, the history of development of Smac mimetics along with the recent development in this field is briefly discussed.

4th International Conference on Condition Monitoring of Machinery in Non-Stationary Operations

CERN Document Server

Zimroz, Radoslaw; Bartelmus, Walter; Haddar, Mohamed

2016-01-01

The book provides readers with a snapshot of recent research and technological trends in the field of condition monitoring of machinery working under a broad range of operating conditions. Each chapter, accepted after a rigorous peer-review process, reports on an original piece of work presented and discussed at the 4th International Conference on Condition Monitoring of Machinery in Non-stationary Operations, CMMNO 2014, held on December 15-16, 2014, in Lyon, France. The contributions have been grouped into three different sections according to the main subfield (signal processing, data mining, or condition monitoring techniques) they are related to. The book includes both theoretical developments as well as a number of industrial case studies, in different areas including, but not limited to: noise and vibration; vibro-acoustic diagnosis; signal processing techniques; diagnostic data analysis; instantaneous speed identification; monitoring and diagnostic systems; and dynamic and fault modeling. This book no...

Research on a Rotating Machinery Fault Prognosis Method Using Three-Dimensional Spatial Representations

Directory of Open Access Journals (Sweden)

Xiaoni Dong

2016-01-01

Full Text Available Process models and parameters are two critical steps for fault prognosis in the operation of rotating machinery. Due to the requirement for a short and rapid response, it is important to study robust sensor data representation schemes. However, the conventional holospectrum defined by one-dimensional or two-dimensional methods does not sufficiently present this information in both the frequency and time domains. To supply a complete holospectrum model, a new three-dimensional spatial representation method is proposed. This method integrates improved three-dimensional (3D holospectra and 3D filtered orbits, leading to the integration of radial and axial vibration features in one bearing section. The results from simulation and experimental analysis on a complex compressor show that the proposed method can present the real operational status and clearly reveal early faults, thus demonstrating great potential for condition-based maintenance prediction in industrial machinery.

Developing an Online Learning Media Using Smartphone for the Electrical Machinery Course

Science.gov (United States)

Muchlas

2018-01-01

This research is aimed to prepare a desktop-based learning media that can be used to support an online lab activities using android smartphones in Electrical Machinery Course at the Department of Electrical Engineering for the undergraduate level. This work uses a conceptual development model which integrates some sub systems of internet…

Repetitive stimulation of autophagy-lysosome machinery by intermittent fasting preconditions the myocardium to ischemia-reperfusion injury.

Science.gov (United States)

Godar, Rebecca J; Ma, Xiucui; Liu, Haiyan; Murphy, John T; Weinheimer, Carla J; Kovacs, Attila; Crosby, Seth D; Saftig, Paul; Diwan, Abhinav

2015-01-01

Autophagy, a lysosomal degradative pathway, is potently stimulated in the myocardium by fasting and is essential for maintaining cardiac function during prolonged starvation. We tested the hypothesis that intermittent fasting protects against myocardial ischemia-reperfusion injury via transcriptional stimulation of the autophagy-lysosome machinery. Adult C57BL/6 mice subjected to 24-h periods of fasting, every other day, for 6 wk were protected from in-vivo ischemia-reperfusion injury on a fed day, with marked reduction in infarct size in both sexes as compared with nonfasted controls. This protection was lost in mice heterozygous null for Lamp2 (coding for lysosomal-associated membrane protein 2), which demonstrate impaired autophagy in response to fasting with accumulation of autophagosomes and SQSTM1, an autophagy substrate, in the heart. In lamp2 null mice, intermittent fasting provoked progressive left ventricular dilation, systolic dysfunction and hypertrophy; worsening cardiomyocyte autophagosome accumulation and lack of protection to ischemia-reperfusion injury, suggesting that intact autophagy-lysosome machinery is essential for myocardial homeostasis during intermittent fasting and consequent ischemic cardioprotection. Fasting and refeeding cycles resulted in transcriptional induction followed by downregulation of autophagy-lysosome genes in the myocardium. This was coupled with fasting-induced nuclear translocation of TFEB (transcription factor EB), a master regulator of autophagy-lysosome machinery; followed by rapid decline in nuclear TFEB levels with refeeding. Endogenous TFEB was essential for attenuation of hypoxia-reoxygenation-induced cell death by repetitive starvation, in neonatal rat cardiomyocytes, in-vitro. Taken together, these data suggest that TFEB-mediated transcriptional priming of the autophagy-lysosome machinery mediates the beneficial effects of fasting-induced autophagy in myocardial ischemia-reperfusion injury.

Repetitive stimulation of autophagy-lysosome machinery by intermittent fasting preconditions the myocardium to ischemia-reperfusion injury

Science.gov (United States)

Godar, Rebecca J; Ma, Xiucui; Liu, Haiyan; Murphy, John T; Weinheimer, Carla J; Kovacs, Attila; Crosby, Seth D; Saftig, Paul; Diwan, Abhinav

2015-01-01

Autophagy, a lysosomal degradative pathway, is potently stimulated in the myocardium by fasting and is essential for maintaining cardiac function during prolonged starvation. We tested the hypothesis that intermittent fasting protects against myocardial ischemia-reperfusion injury via transcriptional stimulation of the autophagy-lysosome machinery. Adult C57BL/6 mice subjected to 24-h periods of fasting, every other day, for 6 wk were protected from in-vivo ischemia-reperfusion injury on a fed day, with marked reduction in infarct size in both sexes as compared with nonfasted controls. This protection was lost in mice heterozygous null for Lamp2 (coding for lysosomal-associated membrane protein 2), which demonstrate impaired autophagy in response to fasting with accumulation of autophagosomes and SQSTM1, an autophagy substrate, in the heart. In lamp2 null mice, intermittent fasting provoked progressive left ventricular dilation, systolic dysfunction and hypertrophy; worsening cardiomyocyte autophagosome accumulation and lack of protection to ischemia-reperfusion injury, suggesting that intact autophagy-lysosome machinery is essential for myocardial homeostasis during intermittent fasting and consequent ischemic cardioprotection. Fasting and refeeding cycles resulted in transcriptional induction followed by downregulation of autophagy-lysosome genes in the myocardium. This was coupled with fasting-induced nuclear translocation of TFEB (transcription factor EB), a master regulator of autophagy-lysosome machinery; followed by rapid decline in nuclear TFEB levels with refeeding. Endogenous TFEB was essential for attenuation of hypoxia-reoxygenation-induced cell death by repetitive starvation, in neonatal rat cardiomyocytes, in-vitro. Taken together, these data suggest that TFEB-mediated transcriptional priming of the autophagy-lysosome machinery mediates the beneficial effects of fasting-induced autophagy in myocardial ischemia-reperfusion injury. PMID:26103523

Diagnostic suite neuro-fuzzy in an advanced alarm monitoring and predictive diagnostic system for rotating machinery

International Nuclear Information System (INIS)

Geruzzi, P.

1999-01-01

The 'Foxboro SCADA', former 'Automation Systems Division' of Nuovo Pignone, at the end of eighty years, has been involved in the development of a flexible and powerful Diagnostic System for Rotating Machinery designed and manufactured in other divisions of the Company. This system amalgamates, in a single computer, all the functionality nowadays necessary to correctly manage locally and remotely the Evolutionary Maintenance of rotating machines as well as the relevant plants. It's specially designed to plan preventive and emergency maintenance procedures and to help the maintenance staff/service in preventing the occurrence of failures or severe damage to complete turbo-machinery plant including turbine, compressor and other machines. The system is designed to supervise and to analyze the operating state of one or more turbo- machinery units such as turbo-compressors, turbo-generators and turbo-pumps giving an effective support to plan preventive and breakdown maintenance monitoring the performances of each turbo-group's element and analyzing a large number of thermodynamic and mechanical parameters related to high pressure turbines, low pressure turbines, combustion chambers, axial compressors and load (compressors, generators, and pumps). A brief presentation of the system is provided (author) (ml)

A Study on the Current Oil and Gas Price Formula and Its Improvement

Energy Technology Data Exchange (ETDEWEB)

Park, Chang Won; Lee, Young Koo [Korea Energy Economics Institute, Euiwang (Korea)

2000-12-01

The object of this study is to suggest some improvements on current price formulas on oil and gas which have been pivotal roles in the process of Korean economic growth. This study first examines basic frames and transition of oil and gas pricing in Korea and then finds some suggestions on them by scrutinizing their theoretical backgrounds. This study finds several problems on oil and gas pricing formulas. (a) In a model that is now studied to evaluate the current domestic oil price, the costs associated with oil security such as oil stockpile are fully penetrated into oil price without their fair evaluations. There is no evaluation principle on the costs occurred in oil supply security. (b) The Rate Of Equity(ROE), a crucial factor in town-gas pricing which is strictly controlled, is directly connected to the average interest rate on saving accounts of domestic commercial banks. Some arguments may have rise about inclusion a risk factor on ROE in order to compensate the uncertainty of town-gas business. (c) New demand for natural gas which is generated by new technologies or machinery and tools can help reduce the costs occurred from seasonal imbalance between power sector and gas sector. So it is also important to decide how to include the beneficiary of cost reduction in town-gas pricing. In order to evaluate the proper price levels, this study tests energy supply security by adopting methodologies such as Herfindahl Index and Portfolio Variance Risk. They can help develop the method to effectively improve the energy security and include the proper energy security costs into energy prices. This study also provides some suggestions for betterment of current ROE decision rule in town-gas business and for improvement of current town-gas policy that government subsidizes newly developed demand for strengthening price competitiveness in the early stage. (author). 145 refs., 16 figs., 49 tabs.

Decontamination of cosmetic and their raw materials by radiation

International Nuclear Information System (INIS)

Virzeu, D.M.

1990-01-01

The effects of gamma radiation over some cosmetic materials (solvent; thickening, talc, wax, vegetal oils, mineral, animal and synthetic oils, grease, emulsifying, conserving anti oxidizing and vitamin) are shown. The doses used were 20 KGy and 50 KGy, that are considered sterilizing and used in medical-surgical materials. The relation of the showed products is useful as a radio sensibility standard, but both can take as an indicator of what can be or not irradiated. (C.G.C.)

Research Using Virtual Reality: Mobile Machinery Safety in the 21st Century

Directory of Open Access Journals (Sweden)

Giselle P. Delgado

2013-04-01

Full Text Available Whole-body vibration is a significant health risk for between 4% and 7% of the work force in North America. In addition, many factors compound the health risks of heavy machinery operators. For example, twisted trunk and neck postures stiffen the spine and increase the transmission of vibration to the head. Similarly, workers adopt awkward postures in order to gain appropriate lines of sight for machine operations. Although the relative contribution of these various issues can be evaluated in field studies and models, we propose that virtual reality is a powerful medium for investigating issues related to health and safety in mining machine operators. We have collected field data of posture and vibration, as well as visual environment, for a forklift operating in a warehouse. This paper describes the process and outcome of this field data collection, and provides a discussion on the next steps to develop and test the virtual reality model to enable laboratory testing. Our ongoing studies will evaluate the interplay between posture and vibration under conditions replicating routine heavy machinery operations, such as underground mining.

49 CFR 1242.42 - Administration, repair and maintenance, machinery repair, equipment damaged, dismantling retired...

Science.gov (United States)

2010-10-01

... repair, equipment damaged, dismantling retired property, fringe benefits, other casualties and insurance, lease rentals, joint facility rents, other rents, depreciation, joint facility, repairs billed to others... maintenance, machinery repair, equipment damaged, dismantling retired property, fringe benefits, other...

40 CFR 408.101 - Specialized definitions.

Science.gov (United States)

2010-07-01

... shall apply to this subpart. (b) The term oil and grease shall mean those components of a waste water amenable to measurement by the method described in Methods for Chemical Analysis of Water and Wastes, 1971, Environmental Protection Agency, Analytical Quality Control Laboratory, page 217. (c) The term seafood shall...

40 CFR 408.41 - Specialized definitions.

Science.gov (United States)

2010-07-01

... shall apply to this subpart. (b) The term oil and grease shall mean those components of a waste water amenable to measurement by the method described in Methods for Chemical Analysis of Water and Wastes, 1971, Environmental Protection Agency, Analytical Quality Control Laboratory, page 217. (c) The term seafood shall...

The current pollution status of the new Calabar river in the Niger ...

African Journals Online (AJOL)

Administrator

area are directly dependent on the river for their agricul- ... the water itself, but also to the danger of diffusion of toxic substances into other ... Temperature and pH of the water samples were ... phosphate, nitrate, oil and grease, cadmium, copper, nickel, lead, mercury ..... composition and molecular mechanisms including cell.

Impact of effluent from Bodija abattoir on the physico- chemical ...

African Journals Online (AJOL)

SERVER

2007-08-06

Aug 6, 2007 ... gross pollution of the aquatic environment with concomi- tant increase in water borne diseases ... pollution potential of meat processing and slaughter- house plants has been estimated at over one .... were picked with clean plastic containers and glass containers (for oil and grease) at points where there ...

40 CFR 417.156 - Pretreatment standards for new sources.

Science.gov (United States)

2010-07-01

... standard shall be: (1) For normal operation of spray drying towers above, the following values pertain.... Oil and grease Do. pH Do. (2) For air quality restricted operation of a spray drying tower, but only... GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Spray Dried...

Folding machineries displayed on a cation-exchanger for the concerted refolding of cysteine- or proline-rich proteins

Directory of Open Access Journals (Sweden)

Lee Dae-Hee

2009-03-01

Full Text Available Abstract Background Escherichia coli has been most widely used for the production of valuable recombinant proteins. However, over-production of heterologous proteins in E. coli frequently leads to their misfolding and aggregation yielding inclusion bodies. Previous attempts to refold the inclusion bodies into bioactive forms usually result in poor recovery and account for the major cost in industrial production of desired proteins from recombinant E. coli. Here, we describe the successful use of the immobilized folding machineries for in vitro refolding with the examples of high yield refolding of a ribonuclease A (RNase A and cyclohexanone monooxygenase (CHMO. Results We have generated refolding-facilitating media immobilized with three folding machineries, mini-chaperone (a monomeric apical domain consisting of residues 191–345 of GroEL and two foldases (DsbA and human peptidyl-prolyl cis-trans isomerase by mimicking oxidative refolding chromatography. For efficient and simple purification and immobilization simultaneously, folding machineries were fused with the positively-charged consecutive 10-arginine tag at their C-terminal. The immobilized folding machineries were fully functional when assayed in a batch mode. When the refolding-facilitating matrices were applied to the refolding of denatured and reduced RNase A and CHMO, both of which contain many cysteine and proline residues, RNase A and CHMO were recovered in 73% and 53% yield of soluble protein with full enzyme activity, respectively. Conclusion The refolding-facilitating media presented here could be a cost-efficient platform and should be applicable to refold a wide range of E. coli inclusion bodies in high yield with biological function.

Necrosome core machinery: MLKL.

Science.gov (United States)

Zhang, Jing; Yang, Yu; He, Wenyan; Sun, Liming

2016-06-01

In the study of regulated cell death, the rapidly expanding field of regulated necrosis, in particular necroptosis, has been drawing much attention. The signaling of necroptosis represents a sophisticated form of a death pathway. Anti-caspase mechanisms (e.g., using inhibitors of caspases, or genetic ablation of caspase-8) switch cell fate from apoptosis to necroptosis. The initial extracellular death signals regulate RIP1 and RIP3 kinase activation. The RIP3-associated death complex assembly is necessary and sufficient to initiate necroptosis. MLKL was initially identified as an essential mediator of RIP1/RIP3 kinase-initiated necroptosis. Recent studies on the signal transduction using chemical tools and biomarkers support the idea that MLKL is able to make more functional sense for the core machinery of the necroptosis death complex, called the necrosome, to connect to the necroptosis execution. The experimental data available now have pointed that the activated MLKL forms membrane-disrupting pores causing membrane leakage, which extends the prototypical concept of morphological and biochemical events following necroptosis happening in vivo. The key role of MLKL in necroptosis signaling thus sheds light on the logic underlying this unique "membrane-explosive" cell death pathway. In this review, we provide the general concepts and strategies that underlie signal transduction of this form of cell death, and then focus specifically on the role of MLKL in necroptosis.

Development of inspection techniques for quantitatively measuring surface contamination on SRM hardware

Science.gov (United States)

Law, R. D.

1989-01-01

A contaminant is any material or substance which is potentially undesirable or which may adversely affect any part, component, or assembly. Contamination control of SRM hardware surfaces is a serious concern, for both Thiokol and NASA, with particular concern for contaminants which may adversely affect bonding surfaces. The purpose of this study is to develop laboratory analytical techniques which will make it possible to certify the cleanliness of any designated surface, with special focus on particulates (dust, dirt, lint, etc.), oils (hydrocarbons, silicones, plasticizers, etc.), and greases (HD-2, fluorocarbon grease, etc.). The hardware surfaces of concern will include D6AC steel, aluminum alloys, anodized aluminum alloys, glass/phenolic, carbon/phenolic, NBR/asbestos-silica, and EPDM rubber.

Regulation of FA and TAG biosynthesis pathway genes in endosperms and embryos of high and low oil content genotypes of Jatropha curcas L.

Science.gov (United States)

Sood, Archit; Chauhan, Rajinder Singh

2015-09-01

The rising demand for biofuels has raised concerns about selecting alternate and promising renewable energy crops which do not compete with food supply. Jatropha (Jatropha curcas L.), a non-edible energy crop of the family euphorbiaceae, has the potential of providing biodiesel feedstock due to the presence of high proportion of unsaturated fatty acids (75%) in seed oil which is mainly accumulated in endosperm and embryo. The molecular basis of seed oil biosynthesis machinery has been studied in J. curcas, however, what genetic differences contribute to differential oil biosynthesis and accumulation in genotypes varying for oil content is poorly understood. We investigated expression profile of 18 FA and TAG biosynthetic pathway genes in different developmental stages of embryo and endosperm from high (42%) and low (30%) oil content genotypes grown at two geographical locations. Most of the genes showed relatively higher expression in endosperms of high oil content genotype, whereas no significant difference was observed in endosperms versus embryos of low oil content genotype. The promoter regions of key genes from FA and TAG biosynthetic pathways as well as other genes implicated in oil accumulation were analyzed for regulatory elements and transcription factors specific to oil or lipid accumulation in plants such as Dof, CBF (LEC1), SORLIP, GATA and Skn-1_motif etc. Identification of key genes from oil biosynthesis and regulatory elements specific to oil deposition will be useful not only in dissecting the molecular basis of high oil content but also improving seed oil content through transgenic or molecular breeding approaches. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

Effects of dietary lipid sources on performance and apparent total tract digestibility of lipids and energy when fed to nursery pigs.

Science.gov (United States)

Mendoza, S M; van Heugten, E

2014-02-01

Acidulated fats and oils are by-products of the fat-refining industry. They contain high levels of FFA and are 10% to 20% less expensive than refined fats and oils. Two studies were designed to measure the effects of dietary lipid sources low or high in FFA on growth performance and apparent total tract digestibility (ATTD) of lipids and GE in nursery pigs. In Exp. 1, 189 pigs at 14 d postweaning (BW of 9.32 ± 0.11 kg) were used for 21 d with 9 replicate pens per treatment and 3 pigs per pen. Dietary treatments consisted of a control diet without added lipids and 6 diets with 6% inclusion of lipids. Four lipid sources were combined to create the dietary treatments with 2 levels of FFA (0.40% or 54.0%) and 3 degrees of fat saturation (iodine value [IV] = 77, 100, or 123) in a 2 × 3 factorial arrangement. Lipid sources were soybean oil (0.3% FFA and IV = 129.4), soybean-cottonseed acid oil blend (70.5% FFA and IV = 112.9), choice white grease (0.6% FFA and IV = 74.8), and choice white acid grease (56.0% FFA and IV = 79.0). Addition of lipid sources decreased ADFI (810 vs. 872 g/d; P = 0.018) and improved G:F (716 vs. 646 g/kg; P source. Fat increased (P sources.

Reconstitution of Biosynthetic Machinery for the Synthesis of the Highly Elaborated Indole Diterpene Penitrem

DEFF Research Database (Denmark)

Liu, Chengwei; Tagami, Koichi; Minami, Atsushi

2015-01-01

KULNJ). Importantly, without conventional gene disruption, reconstitution of the biosynthetic machinery provided sufficient data to determine the pathway. It was thus demonstrated that the Aspergillus oryzae reconstitution system is a powerful method for studying the biosynthesis of complex natural products....

Transesterification of jojoba oil, sunflower oil, neem oil, rocket seed oil and linseed oil by tin catalysts

International Nuclear Information System (INIS)

Shah, Mazloom; Tariq, Muhammad; Ali, Saqib; Guo, Qing-Xiang; Fu, Yao

2014-01-01

The methanolysis of jojoba oil has been studied in the presence of tin powder, dibutyltin diacetate (C 4 H 9 ) 2 Sn(OOCCH 3 ) 2 , dioctyltin diacetate (C 8 H 17 ) 2 Sn(OOCCH 3 ) 2 , dibutyltin oxide (C 4 H 9 ) 2 SnO, dioctyltin oxide (C 8 H 17 ) 2 SnO, diphenyltin oxide (C 6 H 5 ) 2 SnO, dibutyltin chloride dihydroxide (C 4 H 9 ) 2 Sn(OH) 2 Cl, butyltinhydroxide hydrate (C 4 H 9 )Sn(=O)OH.xH 2 O, Ni nanoparticles and Pd nanoparticles act as catalysts. Among these, 1 weight % of dibutyltin diacetate shows the maximum conversion. Then, methanolysis of sunflower oil, neem oil, rocket seed oil and linseed oil into methyl esters studied in the presence of 1% dibutyltin diacetate as a catalyst and was compared their percentage conversions. The experimental yield for the conversion of jojoba oil, sunflower oil, neem oil, rocket seed oil and linseed oil into biodiesel was found to be 71%, 51%, 50.78%, 40.90% and 39.66%, respectively. The experimental yield of the conversion of jojoba oil into methyl esters was found to be increased up to 96% by increasing reaction time, without emulsion formation. The synthesis of jojoba seed oil biodiesel (JSOB), soybean oil biodiesel (SOB), neem oil biodiesel (NOB), rocket seed oil biodiesel (RSOB) and linseed oil biodiesel (LSOB) was confirmed by NMR ( 1 H and 13 C) and FT-IR analyses of biodiesel. - Highlights: • Transesterification of jojoba oil into biodiesel by tin and nano catalysts. • 1 weight % dibutyltin diacetate showed highest yield at 60 °C. • Catalytic conversion comparison of five oils using dibutyltin diacetate • The experimental yield of the conversion of jojoba oil increased with time. • FT-IR and NMR ( 1 H and 13 C) characterization

Operation and Maintenance of Clarks Hill Lake, Savannah River, Georgia, and South Carolina.

Science.gov (United States)

1981-10-01

gray Gnatcatcher C/S x X Regulus satrapa Golden-crowned Kinglet U/W X R. calendula Ruby-crowned Kinglet C/W X Anthus spinoletta Water Pipit U/W X...water uses. 2. All waters shall be free from oil , 2. The waters of the State scum and floating debris associated shall be free at all times with...municipal or domestic sewage, from floating debris, oil , industrial waste or other discharges grease, scum, and other in amounts sufficient to be unsightly

A joint time-invariant wavelet transform and kurtosis approach to the improvement of in-line oil debris sensor capability

International Nuclear Information System (INIS)

Fan, X; Liang, M; Yeap, T

2009-01-01

In-line oil debris sensors are important devices for the detection of machinery failures. However, two key issues remain to be addressed to more effectively make use of the existing oil debris sensors: the responsiveness to early machine failures and false alarms. The responsiveness level depends on the size of the debris that can be detected by an oil debris sensor. The detectable particle size in turn is mainly limited by the background noise. The false alarms are often caused by spurious impulses such as vibration-like signals. The challenge of improving the responsiveness and reducing false alarms lies in the very weak particle signals and their similarity to spurious signals. In this paper, a joint time-invariant wavelet transform and kurtosis analysis method is proposed to address the two issues simultaneously. The proposed method has been tested by extracting signatures of ultra-small metal particles from background noise and a wide range of simulated vibration-like and real vibration signals. Our test results have demonstrated that the proposed method can effectively detect very weak particle signals buried in strong background noise and eliminate vibration-like spurious signals. The implementation of the proposed method will substantially enhance many existing oil debris sensors

OPTIMIZATION MODEL FOR VEHICLE ROUTING AND EQUIPMENT REPLACEMENT IN FARM MACHINERY

OpenAIRE

Grano, Carolina; Abensur, Eder

2017-01-01

ABSTRACT: An equipment replacement decision takes into account economic engineering models based on discounted cash flow (DCF) such as the Annual Equivalent Cost (AEC). Despite a large number of researches on industrial assets replacement, there is a lack of studies applied to farm goods. This study aimed at assessing an alternative model for economic decision analysis on farm machinery replacement, with no restrictions on the number of replacements and assessed goods during a defined timelin...

Triple Recycling Channel Strategies for Remanufacturing of Construction Machinery in a Retailer-Dominated Closed-Loop Supply Chain

Directory of Open Access Journals (Sweden)

Min Huang

2017-12-01

Full Text Available Firms engaged in remanufacturing activities generally adopt more than one recycling channel to collect more used products and gain more profits. This paper explores the optimal strategies for a retailer-dominated closed-loop supply chain (CLSC with a triple recycling channel in the construction machinery remanufacturing context. In this special system, the retailer is the leader and authorized by the original equipment manufacturer (OEM to remanufacture. Moreover, the OEM, the retailer, and the secondary market all take part in the used products collection activities. Considering the differentiation of the OEM, the retailer, and the secondary market in collecting the used construction machinery, a mathematical model of the CLSC system based on reasonable assumptions is built, the closed-form optimal pricing decisions are derived, and the optimal collection efforts allocation strategies are explored within the framework of the game theory. In addition, the impacts of the reverse logistics cost coefficient, the competing coefficient, and the buy-back price coefficient on the supply chain performance are elaborately analyzed. These achievements provide decision makers with managerial insights and offer efficient guidelines for the construction machinery remanufacturing firms to solve similar puzzles.