WorldWideScience

Sample records for machine side requesters

  1. A double-sided linear primary permanent magnet vernier machine.

    Science.gov (United States)

    Du, Yi; Zou, Chunhua; Liu, Xianxing

    2015-01-01

    The purpose of this paper is to present a new double-sided linear primary permanent magnet (PM) vernier (DSLPPMV) machine, which can offer high thrust force, low detent force, and improved power factor. Both PMs and windings of the proposed machine are on the short translator, while the long stator is designed as a double-sided simple iron core with salient teeth so that it is very robust to transmit high thrust force. The key of this new machine is the introduction of double stator and the elimination of translator yoke, so that the inductance and the volume of the machine can be reduced. Hence, the proposed machine offers improved power factor and thrust force density. The electromagnetic performances of the proposed machine are analyzed including flux, no-load EMF, thrust force density, and inductance. Based on using the finite element analysis, the characteristics and performances of the proposed machine are assessed.

  2. A Double-Sided Linear Primary Permanent Magnet Vernier Machine

    Directory of Open Access Journals (Sweden)

    Yi Du

    2015-01-01

    Full Text Available The purpose of this paper is to present a new double-sided linear primary permanent magnet (PM vernier (DSLPPMV machine, which can offer high thrust force, low detent force, and improved power factor. Both PMs and windings of the proposed machine are on the short translator, while the long stator is designed as a double-sided simple iron core with salient teeth so that it is very robust to transmit high thrust force. The key of this new machine is the introduction of double stator and the elimination of translator yoke, so that the inductance and the volume of the machine can be reduced. Hence, the proposed machine offers improved power factor and thrust force density. The electromagnetic performances of the proposed machine are analyzed including flux, no-load EMF, thrust force density, and inductance. Based on using the finite element analysis, the characteristics and performances of the proposed machine are assessed.

  3. Brushless machine having ferromagnetic side plates and side magnets

    Science.gov (United States)

    Hsu, John S

    2012-10-23

    An apparatus is provided having a cylindrical stator and a rotor that is spaced from a stator to define an annular primary air gap that receives AC flux from the stator. The rotor has a plurality of longitudinal pole portions disposed parallel to the axis of rotation and alternating in polarity around a circumference of the rotor. Each longitudinal pole portion includes portions of permanent magnet (PM) material and at least one of the longitudinal pole portions has a first end and an opposing second end and a side magnet is disposed adjacent the first end and a side pole is disposed adjacent the second end.

  4. On Cascade Source Coding with A Side Information "Vending Machine"

    CERN Document Server

    Ahmadi, Behzad; Choudhuri, Chiranjib; Mitra, Urbashi

    2012-01-01

    The model of a side information "vending machine" accounts for scenarios in which acquiring side information is costly and thus should be done efficiently. In this paper, the three-node cascade source coding problem is studied under the assumption that a side information vending machine is available either at the intermediate or at the end node. In both cases, a single-letter characterization of the available trade-offs among the rate, the distortions in the reconstructions at the intermediate and at the end node, and the cost in acquiring the side information are derived under given conditions.

  5. "Source Coding With a Side Information ""Vending Machine"""

    OpenAIRE

    Weissman, Tsachy; Permuter, Haim H.

    2011-01-01

    We study source coding in the presence of side information, when the system can take actions that affect the availability, quality, or nature of the side information. We begin by extending the Wyner-Ziv problem of source coding with decoder side information to the case where the decoder is allowed to choose actions affecting the side information. We then consider the setting where actions are taken by the encoder, based on its observation of the source. Actions may have costs that are commens...

  6. Machining variability impacts on the strength of a 'chair-side' CAD-CAM ceramic.

    LENUS (Irish Health Repository)

    Addison, Owen

    2012-08-01

    To develop a novel methodology to generate specimens for bi-axial flexure strength (BFS) determination from a \\'chair-side\\' CAD-CAM feldspathic ceramic with surface defect integrals analogous to the clinical state. The hypotheses tested were: BFS and surface roughness (R(a)) are independent of machining variability introduced by the renewal or deterioration of form-grinding tools and that a post-machining annealing cycle would significantly modify BFS.

  7. Rotary ultrasonic elliptical machining for side milling of CFRP: tool performance and surface integrity.

    Science.gov (United States)

    Geng, Daxi; Zhang, Deyuan; Xu, Yonggang; He, Fengtao; Liu, Dapeng; Duan, Zuoheng

    2015-05-01

    The rotary ultrasonic elliptical machining (RUEM) has been recognized as a new effective process to machining circular holes on CFRP materials. In CFRP face machining, the application of grinding tools is restricted for the tool clogging and the machined surface integrity. In this paper, we proposed a novel approach to extend the RUEM process to side milling of CFRP for the first time, which kept the effect of elliptical vibration in RUEM. The experiment apparatus was developed, and the preliminary experiments were designed and conducted, with comparison to conventional grinding (CG). The experimental results showed that when the elliptical vibration was applied in RUEM, a superior cutting process can be obtained compared with that in CG, including providing reduced cutting forces (2-43% decrement), an extended tool life (1.98 times), and improved surface integrity due to the intermittent material removal mechanism and the excellent chip removal conditions achieved in RUEM. It was concluded that the RUEM process is suitable to mill flat surface on CFRP composites.

  8. Distributed and Cascade Lossy Source Coding with a Side Information "Vending Machine"

    CERN Document Server

    Ahmadi, Behzad

    2011-01-01

    Source coding with a side information "vending machine" is a recently proposed framework in which the statistical relationship between the side information and the source, instead of being given and fixed as in the classical Wyner-Ziv problem, can be controlled by the decoder. This control action is selected by the decoder based on the message encoded by the source node. Unlike conventional settings, the message can thus carry not only information about the source to be reproduced at the decoder, but also control information aimed at improving the quality of the side information. In this paper, the single-letter characterization of the trade-offs between rate, distortion and cost associated with the control actions is extended from the previously studied point-to-point set-up to two basic multiterminal models. First, a distributed source coding model is studied, in which an arbitrary number of encoders communicate over rate-limited links to a decoder, whose side information can be controlled. The control acti...

  9. A Reordering Model Using a Source-Side Parse-Tree for Statistical Machine Translation

    Science.gov (United States)

    Hashimoto, Kei; Yamamoto, Hirofumi; Okuma, Hideo; Sumita, Eiichiro; Tokuda, Keiichi

    This paper presents a reordering model using a source-side parse-tree for phrase-based statistical machine translation. The proposed model is an extension of IST-ITG (imposing source tree on inversion transduction grammar) constraints. In the proposed method, the target-side word order is obtained by rotating nodes of the source-side parse-tree. We modeled the node rotation, monotone or swap, using word alignments based on a training parallel corpus and source-side parse-trees. The model efficiently suppresses erroneous target word orderings, especially global orderings. Furthermore, the proposed method conducts a probabilistic evaluation of target word reorderings. In English-to-Japanese and English-to-Chinese translation experiments, the proposed method resulted in a 0.49-point improvement (29.31 to 29.80) and a 0.33-point improvement (18.60 to 18.93) in word BLEU-4 compared with IST-ITG constraints, respectively. This indicates the validity of the proposed reordering model.

  10. Positioning method of a cylindrical cutter for ruled surface machining based on minimizing one-sided Hausdorff distance

    Institute of Scientific and Technical Information of China (English)

    Cao Lixin; Dong Lei

    2015-01-01

    Motivated by the definition of the machining errors induced by tool path planning methods, a mapping curve of the tool axis of a cylindrical cutter is constructed on the tool surface. The mapping curve is a typical one that can be used to express the closeness between the tool surface and the surface to be machined. A novel tool path planning method is proposed for flank or plunge milling ruled surfaces based on the minimization of the one-sided Hausdorff distance (HD) from the mapping curve to the surface to be machined. It is a nonlinear optimization problem in best uniform approximation (BUA) or Chebyshev sense. A mathematical programming model for computing the minimum one-sided HD is proposed. The linearization method of the programming model is provided and the final optimal solutions are obtained by simplex method. The effectiveness of the proposed BUA method is verified by two numerical examples and compared with the least squares (LS) and double point offset (DPO) methods. The variation in tool orientation induced by the optimization of the tool positions is also evaluated.

  11. Building a Robust Client-Side Protection Against Cross Site Request Forgery

    Directory of Open Access Journals (Sweden)

    Abdalla AlAmeen

    2015-06-01

    Full Text Available In recent years, the web has been an indispensable part of business all over the world and web browsers have become the backbones of today's systems and applications. Unfortunately, the number of web application attacks has increased a great deal, so the matter of concern is securing web applications. One of the most serious cyber-attacks has been by cross site request forgery (CSRF. CSRF has been recognized among the major threats to web applications and among the top ten worst vulnerabilities for web applications. In a CSRF attack, an attacker takes liberty be authorized to take a sensitive action on a target website on behalf of a user without his knowledge. This paper, providing an overview about CSRF attack, describes the various possible attacks, the developed solutions, and the risks in the current preventive techniques. This paper comes up with a highly perfect protection mechanism against reflected CSRF called RCSR. RCSR is a tool gives computer users with full control on the attack. RCSR tool relies on specifying HTTP request source, whether it comes from different tab or from the same one of a valid user, it observes and intercepts every request that is passed through the user’s browser and extracts session information, post the extracted information to the Server, then the server create a token for user's session. We checked the working of RCSR extension, our evaluation results show that it is working well and it successfully protects web applications against reflected CSRF.

  12. Reverse engineering smart card malware using side channel analysis with machine learning techniques

    CSIR Research Space (South Africa)

    Djonon Tsague, Hippolyte

    2016-12-01

    Full Text Available by evaluating its power consumption only. Besides well-studied methods from side channel analysis, we apply a combination of dimensionality reduction techniques in the form of PCA and LDA models to compress the large amount of data generated while preserving...

  13. 双面抛光机内外齿圈齿比的研究%Study on Inner and Outer Gears Ratio of Double-Sided Polishing Machine

    Institute of Scientific and Technical Information of China (English)

    金程; 李伟

    2011-01-01

    双面抛光机作为超精密加工的重要设备,它的加工质量主要由工件表面加工轨迹和抛光机的振动所决定.作为抛光机的关键因素之一,工件表面的加工轨迹和内外齿圈齿比有着直接的联系.调整内外齿圈齿比是双面抛光机进行生产之前最重要的一件事.最新的研究表明,双面抛光机的振动也与内外齿圈齿比有很大的联系,但是具体的关联理论尚不明确.文章通过具体实验调整内外齿圈齿比得到1个优化的参数使双面抛光机的振动减小,为固定内外齿圈齿比双面抛光机的制造提供参考,同时在实验中,还发现了抛光机振动与加工轨迹的1个新的关系.%The double-sided polishing machine has been considered as important equipment for ultra-precision processing, its processing quality is mainly determined by processing trail on work-piece and the vibration of polishing machine. As the key factors to the machine, it is well known that the processing trail on work-piece is direct relative with the inner and outer gears ratio. Adjusting the ratio to make the trail even is the first thing to concern before polishing machine running. However, the latest study shows that the vibration of polishing machine is also interacted with the inner and outer gears ratio. The paper carried out experiment to get an optimal parameter through adjusting inner and outer gears ratio to reduce vibration of double-sided polishing machine, thus provided a reference for manufacture double-sided polishing machine with fixed inner and outer gears ratio. Mean while, a new relationship between the trail and the vibration was discovered.

  14. Controller for the Machine-Side Power Converter of a 2kW Switched Reluctance Motor; Controlador del Convertidor Electronico de Potencia Lado Maquina de un Motor de Reluctancia Variable de 2kW

    Energy Technology Data Exchange (ETDEWEB)

    Vazquez, C.

    2006-07-01

    The ACE2 project deals with the development of a kynetic energy storage (KES) system for power peak shaving in high speed railway substations. This KES system consists in a double power converter which drives a switched reluctance machine (SRM) along with a flywheel operating in a wide speed range. This document presents from a technical point of view the features of the controller for the machine-side power converter of a 2kW SRM prototype. Hardware and software issues are treated in detail. (Author)

  15. Controller for the Machine-Side Power Converter of a 2kW Switched Reluctance Motor; Controlador del Convertidor Electronico de Potencia Lado Red de un Motor de Reluctancia Variable de 2kW

    Energy Technology Data Exchange (ETDEWEB)

    Vazquez, C.

    2006-12-19

    The ACE2 project deals with the development of a kynetic energy storage (KES) system for power peak shaving in high speed railway substations. This KES system consists in a double power converter which drives a switched reluctance machine (SRM) along with a flywheel operating in a wide speed range. This document presents from a technical point of view the features of the controller for the machine-side power converter of a 2kW SRM prototype. Hardware and software issues are treated in detail. (Author)

  16. Canon multifunction copier machines – now with onsite support!

    CERN Multimedia

    2013-01-01

    Following a retendering process in 2012, the IT Department is pleased to announce that leased multifunction copier machines are now covered by onsite support, provided by Canon technicians via the CERN Service Desk support system.   You can now contact the Service Desk regarding any problems or requests for toner: Telephone: 77777 Email: Service-Desk@cern.ch Please remember to quote the machine printer name and/or serial number (marked on the side of the machine). The following submission forms are available online: Report a failure with a printer or copier Request for network printer or copier installation or move Request toner/ink for my printer or copier The website below details the range of models available, all of which include print, photocopy and scan-to-mail functions as standard. These multifunction copier machines are leased subject to a monthly charge (minimum of 48 months) plus a “per click” charge to cover consumables (except staples), leaving you noth...

  17. Part Machinability Evaluation System

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    In the early design period, estimation of the part or the whole product machinability is useful to consider the function and process request of the product at the same time so as to globally optimize the design decision. This paper presents a part machinability evaluation system, discusses the general restrictions of part machinability, and realizes the inspection of these restrictions with the relation between tool scan space and part model. During the system development, the expansibility and understandability were considered, and an independent restriction algorithm library and a general function library were set up. Additionally, the system has an interpreter and a knowledge manager.

  18. The Vertical Single Side Extending-Hinging Four-Station Modular Machine Tool for Tappet-hole In Cylinder Body%立式单面四工位扩铰缸体挺柱孔组合机床

    Institute of Scientific and Technical Information of China (English)

    吴慧萍; 李前明

    2013-01-01

    This paper provided a vertical single side modular machine tool,which have moving front guiding device and be suitable for multi-species processing,multi-station extending-hinging tappet-hole in cylinder body.The machine positioned workpiece by cylinder base and two pin hole,completed Ⅰ,Ⅲ and Ⅱ,Ⅳ station switching by two groups of activities bolt institutions and two groups of ejecting cylinder,processed two parts simultaneously with moving front guiding device,pawl delivery device and hydraulic clamping mechanism.This can not only save the equipment cost,but also improve production efficiency.%文章介绍了一种带有移动前导向装置,适合一系列多品种加工,多工位扩、铰缸体挺柱孔的组合机床.该机床采用缸体底面和两个销孔的定位方式,运用两组活动插销机构和两组推件油缸同时完成Ⅰ、Ⅲ和Ⅱ、Ⅳ工位的切换,利用移动前导向装置和棘爪输送装置配合液压夹紧,实现两个零件的同时加工.不仅节约了设备成本,而且提高了生产效益.

  19. When Machines Design Machines!

    DEFF Research Database (Denmark)

    2011-01-01

    Until recently we were the sole designers, alone in the driving seat making all the decisions. But, we have created a world of complexity way beyond human ability to understand, control, and govern. Machines now do more trades than humans on stock markets, they control our power, water, gas...... and food supplies, manage our elevators, microclimates, automobiles and transport systems, and manufacture almost everything. It should come as no surprise that machines are now designing machines. The chips that power our computers and mobile phones, the robots and commercial processing plants on which we...... depend, all are now largely designed by machines. So what of us - will be totally usurped, or are we looking at a new symbiosis with human and artificial intelligences combined to realise the best outcomes possible. In most respects we have no choice! Human abilities alone cannot solve any of the major...

  20. Lymphedema as a Cancer Treatment Side Effect

    Science.gov (United States)

    ... Navigating Cancer Care > Side Effects > Lymphedema Request Permissions Lymphedema Approved by the Cancer.Net Editorial Board , 05/ ... years after cancer treatment has ended. Symptoms of lymphedema People with lymphedema in their arm or leg ...

  1. HELPDESK TROUBLESHOOTING REQUESTS

    CERN Multimedia

    2004-01-01

    As of the 08/03/2004 all the repair requests and other communication concerning the CERN tertiary buildings that so far have been transmitted to the TCR via 72201 will be handled directly by the FM helpdesk under the phone number 77777, i.e. problems on systems and equipment as: • Electricity and lighting in office buildings, halls and workshops • Heating and air conditioning in office buildings, halls and workshops • Lifts (excluded the ones in shafts) • Motorised doors • Building structure and equipment: roofs, doors, windows, blinds, etc. • Plumbing • Toilets • Cleaning (CERN wide) • Restaurant equipment • Roads and green areas • Wastes collection The FM Helpdesk is available between 07h30 and 18h30. Troubleshooting requests, complaints and work requests will only be accepted during these opening hours. Outside these opening hours and for any problem in a machine building or on equipment that is ...

  2. HELPDESK TROUBLESHOOTING REQUESTS

    CERN Multimedia

    2004-01-01

    As of the 08/03/2004 all the repair requests and other communication concerning the CERN tertiary buildings that so far have been transmitted to the TCR via 72201 will be handled directly by the FM helpdesk under the phone number 77777, i.e. problems on systems and equipment as: • Electricity and lighting in office buildings, halls and workshops • Heating and air conditioning in office buildings, halls and workshops • Lifts (excluded the ones in shafts) • Motorised doors • Building structure and equipment: roofs, doors, windows, blinds, etc. • Plumbing • Toilets • Cleaning (CERN wide) • Restaurant equipment • Roads and green areas • Wastes collection The FM Helpdesk is available between 07h30 and 18h30. Troubleshooting requests, complaints and work requests will only be accepted during these opening hours. Outside these opening hours and for any problem in a machine building or on equipment that is ...

  3. European side markers effect on traffic safety

    NARCIS (Netherlands)

    Roelfsema, A.; Theeuwes, J.; Alferdinck, J.W.A.M

    1999-01-01

    In 1993 new European legislation regarding side-markers for passenger cars became effective. Volvo requested the TNO-Human Factors Research Institute (HFRI) to investigate the possible safety benefit of this European side-markers configuration. A test panel at TNO- HFRI was used to determine the dif

  4. Machine Translation

    Institute of Scientific and Technical Information of China (English)

    张严心

    2015-01-01

    As a kind of ancillary translation tool, Machine Translation has been paid increasing attention to and received different kinds of study by a great deal of researchers and scholars for a long time. To know the definition of Machine Translation and to analyse its benefits and problems are significant for translators in order to make good use of Machine Translation, and helpful to develop and consummate Machine Translation Systems in the future.

  5. Sustainable machining

    CERN Document Server

    2017-01-01

    This book provides an overview on current sustainable machining. Its chapters cover the concept in economic, social and environmental dimensions. It provides the reader with proper ways to handle several pollutants produced during the machining process. The book is useful on both undergraduate and postgraduate levels and it is of interest to all those working with manufacturing and machining technology.

  6. 75 FR 11936 - Norforge and Machining, Inc., Bushnell, IL; Notice of Termination of Investigation

    Science.gov (United States)

    2010-03-12

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF LABOR Employment and Training Administration Norforge and Machining, Inc., Bushnell, IL; Notice of Termination of... and Machining, Inc., Bushnell, Illinois. The petitioner has requested that the petition be...

  7. HELPDESK TROUBLESHOOTING REQUESTS

    CERN Multimedia

    FM and CSE Group, TS Department

    2004-01-01

    As of the 08/03/2004 all the repair requests and other communication concerning the CERN tertiary buildings that so far have been transmitted to the TCR via 72201 will be handled directly by the FM helpdesk under the phone number 77777, i.e. problems on systems and equipment as: Electricity and lighting in office buildings, halls and workshops Heating and air conditioning in office buildings, halls and workshops Lifts (excluded the ones in shafts) Motorised doors Building structure and equipment: roofs, doors, windows, blinds, etc. Plumbing Toilets Cleaning (CERN wide) Restaurant equipment Roads and green areas Wastes collection The FM Helpdesk is available between 07h30 and 18h30. Troubleshooting requests, complaints and work requests will only be accepted during these opening hours. Outside these opening hours and for any problem in a machine building or on equipment that is not in the list above, you shall continue to contact the TCR under 72201 - 24 hours a day, 365 days a year. Machine buildings are ...

  8. HELPDESK TROUBLESHOOTING REQUESTS

    CERN Multimedia

    TS Department

    2004-01-01

    As of the 08/03/2004 all the repair requests and other communication concerning the CERN tertiary buildings that so far have been transmitted to the TCR via 72201 will be handled directly by the FM helpdesk under the phone number 77777, i.e. problems on systems and equipment as: Electricity and lighting in office buildings, halls and workshops Heating and air conditioning in office buildings, halls and workshops Lifts (excluded the ones in shafts) Motorised doors Building structure and equipment: roofs, doors, windows, blinds, etc. Plumbing Toilets Cleaning (CERN wide) Restaurant equipment Roads and green areas Wastes collection The FM Helpdesk is available between 07h30 and 18h30. Troubleshooting requests, complaints and work requests will only be accepted during these opening hours. Outside these opening hours and for any problem in a machine building or on equipment that is not in the list above, you shall continue to contact the TCR under 72201 - 24 hours a day, 365 days a year. Machine buildings are e...

  9. Road maintaining and constructing machine training center project in Morocco; Morocco doro hoshu kensetsu kiki kunren center project

    Energy Technology Data Exchange (ETDEWEB)

    Hagiwara, T. [Japan Sewage Works Agency, Tokyo (Japan)

    1997-10-25

    This paper describes technical cooperation with Morocco on road maintenance. In the latter half of the 1980`s, road transportation accounted for 95% of traveler transportation and 80% of freight transportation. Thereafter, construction of new roads has been reduced due to financial situation, and maintenance of the existing roads has become the core of road project of the government. The government has requested Japan in 1986 a gratuitous fund cooperation required for building a training facility for road maintenance, and technical cooperation for implementing the training courses. The Japan International Cooperation Agency has built the Morocco road maintaining and constructing machine training center under a gratuitous fund cooperation of about 1.6 billion yen, and provided construction machines, and other machines and appliances. The center inauguration ceremony was held in July 1993. The Japanese side has provided implements and materials, sent professional persons, and accepted trainees. The Moroccan side has taken burden of land development, construction of staff boarding houses and locative structures, and other local costs. The center holds 35 official staff members. The training courses cover operation, servicing, management of machines, and road maintenance, and have a total of 719 persons completed the courses. The five-year project has been completed, and the subsequent project is now being performed by the Moroccan side alone. 5 figs., 4 tabs.

  10. Simple machines

    CERN Document Server

    Graybill, George

    2007-01-01

    Just how simple are simple machines? With our ready-to-use resource, they are simple to teach and easy to learn! Chocked full of information and activities, we begin with a look at force, motion and work, and examples of simple machines in daily life are given. With this background, we move on to different kinds of simple machines including: Levers, Inclined Planes, Wedges, Screws, Pulleys, and Wheels and Axles. An exploration of some compound machines follows, such as the can opener. Our resource is a real time-saver as all the reading passages, student activities are provided. Presented in s

  11. Surface errors in the course of machining precision optics

    Science.gov (United States)

    Biskup, H.; Haberl, A.; Rascher, R.

    2015-08-01

    Precision optical components are usually machined by grinding and polishing in several steps with increasing accuracy. Spherical surfaces will be finished in a last step with large tools to smooth the surface. The requested surface accuracy of non-spherical surfaces only can be achieved with tools in point contact to the surface. So called mid-frequency errors (MSFE) can accumulate with zonal processes. This work is on the formation of surface errors from grinding to polishing by conducting an analysis of the surfaces in their machining steps by non-contact interferometric methods. The errors on the surface can be distinguished as described in DIN 4760 whereby 2nd to 3rd order errors are the so-called MSFE. By appropriate filtering of the measured data frequencies of errors can be suppressed in a manner that only defined spatial frequencies will be shown in the surface plot. It can be observed that some frequencies already may be formed in the early machining steps like grinding and main-polishing. Additionally it is known that MSFE can be produced by the process itself and other side effects. Beside a description of surface errors based on the limits of measurement technologies, different formation mechanisms for selected spatial frequencies are presented. A correction may be only possible by tools that have a lateral size below the wavelength of the error structure. The presented considerations may be used to develop proposals to handle surface errors.

  12. Electric machine

    Science.gov (United States)

    El-Refaie, Ayman Mohamed Fawzi [Niskayuna, NY; Reddy, Patel Bhageerath [Madison, WI

    2012-07-17

    An interior permanent magnet electric machine is disclosed. The interior permanent magnet electric machine comprises a rotor comprising a plurality of radially placed magnets each having a proximal end and a distal end, wherein each magnet comprises a plurality of magnetic segments and at least one magnetic segment towards the distal end comprises a high resistivity magnetic material.

  13. The Machine within the Machine

    CERN Multimedia

    Katarina Anthony

    2014-01-01

    Although Virtual Machines are widespread across CERN, you probably won't have heard of them unless you work for an experiment. Virtual machines - known as VMs - allow you to create a separate machine within your own, allowing you to run Linux on your Mac, or Windows on your Linux - whatever combination you need.   Using a CERN Virtual Machine, a Linux analysis software runs on a Macbook. When it comes to LHC data, one of the primary issues collaborations face is the diversity of computing environments among collaborators spread across the world. What if an institute cannot run the analysis software because they use different operating systems? "That's where the CernVM project comes in," says Gerardo Ganis, PH-SFT staff member and leader of the CernVM project. "We were able to respond to experimentalists' concerns by providing a virtual machine package that could be used to run experiment software. This way, no matter what hardware they have ...

  14. ROME (Request Object Management Environment)

    Science.gov (United States)

    Kong, M.; Good, J. C.; Berriman, G. B.

    2005-12-01

    Most current astronomical archive services are based on an HTML/ CGI architecture where users submit HTML forms via a browser and CGI programs operating under a web server process the requests. Most services return an HTML result page with URL links to the result files or, for longer jobs, return a message indicating that email will be sent when the job is done. This paradigm has a few serious shortcomings. First, it is all too common for something to go wrong and for the user to never hear about the job again. Second, for long and complicated jobs there is often important intermediate information that would allow the user to adjust the processing. Finally, unless some sort of custom queueing mechanism is used, background jobs are started immediately upon receiving the CGI request. When there are many such requests the server machine can easily be overloaded and either slow to a crawl or crash. Request Object Management Environment (ROME) is a collection of middleware components being developed under the National Virtual Observatory Project to provide mechanism for managing long jobs such as computationally intensive statistical analysis requests or the generation of large scale mosaic images. Written as EJB objects within the open-source JBoss applications server, ROME receives processing requests via a servelet interface, stores them in a DBMS using JDBC, distributes the processing (via queuing mechanisms) across multiple machines and environments (including Grid resources), manages realtime messages from the processing modules, and ensures proper user notification. The request processing modules are identical in structure to standard CGI-programs -- though they can optionally implement status messaging -- and can be written in any language. ROME will persist these jobs across failures of processing modules, network outages, and even downtime of ROME and the DBMS, restarting them as necessary.

  15. Machine Learning

    CERN Document Server

    CERN. Geneva

    2017-01-01

    Machine learning, which builds on ideas in computer science, statistics, and optimization, focuses on developing algorithms to identify patterns and regularities in data, and using these learned patterns to make predictions on new observations. Boosted by its industrial and commercial applications, the field of machine learning is quickly evolving and expanding. Recent advances have seen great success in the realms of computer vision, natural language processing, and broadly in data science. Many of these techniques have already been applied in particle physics, for instance for particle identification, detector monitoring, and the optimization of computer resources. Modern machine learning approaches, such as deep learning, are only just beginning to be applied to the analysis of High Energy Physics data to approach more and more complex problems. These classes will review the framework behind machine learning and discuss recent developments in the field.

  16. Abdominal respiration expression of side-view single pig based on machine vision%基于机器视觉的单侧视猪腹式呼吸表达

    Institute of Scientific and Technical Information of China (English)

    马丽; 纪滨

    2012-01-01

    为了监测猪的呼吸急促,引入机器视觉技术构建单侧视猪的腹式呼吸表达。根据猪腹式呼吸时脊腹部分呈起伏的特点,从视频帧的猪轮廓图像中提取形心,确定感兴趣的脊腹线段,然后在垂直方向提取脊线与腹线的截距,接着,构建脊腹线截距描述子(RACID)作为度量脊腹轮廓波动的指标,最后,根据帧序列中随时间变化的RACID,得到猪腹式呼吸表达。逐段检测猪视频腹式呼吸频次,实验结果显示机器法和人工法相关系数为98.23%。%To monitor the tachypnea of pigs, the machine-vision is introduced to construct a model on the pig's abdominal respiration. Firstly, according to the marked dilating and shrinking at ridge-abdomen of pigs, tworidge-abdomen profile segments are ensured based on the centroid of pig's contour. Secondly, the intercepts between both segments are obtained in vertical direction. Thirdly, Ridge-Abdomen Contour Intercept Descriptor (RACID) is created as an index of the fluctuating ones. Finally, the pig abdominal breathing expression is created according to the varying RACID over time. The frequency of the pig abdominal respiration was respectively obtained by the machine-vision method and the artificial method. Experiments showed that the correlation coefficient between the two methods is 98.23%.

  17. Diagnóstico de Fallas en Máquinas Eléctricas Rotatorias Utilizando la Técnica de Espectros de Frecuencia de Bandas Laterales Fault Diagnosis in Rotating Electrical Machines by Side Bands Frequency Spectra Technique

    Directory of Open Access Journals (Sweden)

    Roberto Flores

    2011-01-01

    Full Text Available En el presente trabajo se muestra y se aplica una metodología para el diagnóstico de fallas en máquinas eléctricas rotatorias utilizando la técnica de espectros de frecuencia de bandas laterales de las corrientes de fase. Se establecen sistemas de prueba de laboratorio para verificar las magnitudes de las bandas originadas por fallas tanto mecánicas como eléctricas. Se muestra una serie de resultados para un grupo motor de corriente directa-generador síncrono de 5 kVA desalineado y de dos motores de inducción de 5 HP tipo jaula de ardilla, uno con holgura en soporte de baleros y otro con barras rotas. Además, se comparan los resultados de los espectros empleando un sensor de corriente convencional contra una bobina de Rogowski, obteniendo resultados adecuados para detectar la presencia de falla en las máquinas.In this article a methodology to diagnose faults in rotating electrical machines is presented. The method uses spectral frequency analysis of the phase currents sidebands. Online systems to verify the magnitude of these frequencies, caused not only by mechanical faults but also electrical faults, are presented. The results of a faulty set formed by a direct current motor plus a synchronous generator of 5 kVA and two squirrel-cage induction motors of 5 HP, one with slacked bearings faults and other with broken rotor bars, are presented. Also, the results of the spectra using a conventional current sensor are compared with those of a Rogowski coil, showing that the results of both sensors are suitable to detect machine faults.

  18. Machine Learning

    Energy Technology Data Exchange (ETDEWEB)

    Chikkagoudar, Satish; Chatterjee, Samrat; Thomas, Dennis G.; Carroll, Thomas E.; Muller, George

    2017-04-21

    The absence of a robust and unified theory of cyber dynamics presents challenges and opportunities for using machine learning based data-driven approaches to further the understanding of the behavior of such complex systems. Analysts can also use machine learning approaches to gain operational insights. In order to be operationally beneficial, cybersecurity machine learning based models need to have the ability to: (1) represent a real-world system, (2) infer system properties, and (3) learn and adapt based on expert knowledge and observations. Probabilistic models and Probabilistic graphical models provide these necessary properties and are further explored in this chapter. Bayesian Networks and Hidden Markov Models are introduced as an example of a widely used data driven classification/modeling strategy.

  19. Machine testning

    DEFF Research Database (Denmark)

    De Chiffre, Leonardo

    This document is used in connection with a laboratory exercise of 3 hours duration as a part of the course GEOMETRICAL METROLOGY AND MACHINE TESTING. The exercise includes a series of tests carried out by the student on a conventional and a numerically controled lathe, respectively. This document...

  20. Representational Machines

    DEFF Research Database (Denmark)

    Petersson, Dag; Dahlgren, Anna; Vestberg, Nina Lager

    to the enterprises of the medium. This is the subject of Representational Machines: How photography enlists the workings of institutional technologies in search of establishing new iconic and social spaces. Together, the contributions to this edited volume span historical epochs, social environments, technological...

  1. Adding machine and calculating machine

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    In 1642 the French mathematician Blaise Pascal(1623-1662) invented a machine;.that could add and subtract. It had.wheels that each had: 1 to 10 marked off along its circumference. When the wheel at the right, representing units, made one complete circle, it engaged the wheel to its left, represents tens, and moved it forward one notch.

  2. Behind the machines

    CERN Document Server

    Laëtitia Pedroso

    2010-01-01

    One of the first things we think about when someone mentions physics is the machines. But behind the machines, there are the men and women who design, build and operate them. In an exhibition at the Thinktank planetarium’s art gallery in Birmingham (UK), Claudia Marcelloni and her husband Neal Hartman—she is a photographer and Outreach Officer for ATLAS, while he is an engineer working on the ATLAS pixel detector—explore the human side of scientists.   The exhibition at the Thinktank Planetarium art gallery, Birmingham (UK). It all began two years ago with the publication of Exploring the mystery of matter, a book about ATLAS. “A Norwegian physicist friend, Heidi Sandaker, saw my photographs and suggested that I display them in a museum. I thought this was an interesting idea, except that the photos consisted entirely of depictions of machinery, with human beings completely absent. For me, showing the people who are behind the machines and the fascination ...

  3. Genesis machines

    CERN Document Server

    Amos, Martyn

    2014-01-01

    Silicon chips are out. Today's scientists are using real, wet, squishy, living biology to build the next generation of computers. Cells, gels and DNA strands are the 'wetware' of the twenty-first century. Much smaller and more intelligent, these organic computers open up revolutionary possibilities. Tracing the history of computing and revealing a brave new world to come, Genesis Machines describes how this new technology will change the way we think not just about computers - but about life itself.

  4. Shuttle requests

    CERN Multimedia

    2007-01-01

    Please note that starting from 1 March 2007, the shuttle requests: for official visits or bidders' conferences on the CERN site; towards/from the airport or central Geneva; for long distances, shall be made via Fm.Support@cern.ch or by calling 77777. The radio taxi will still be reachable at 76969. TS/FM Group

  5. Mineral mining machines

    Energy Technology Data Exchange (ETDEWEB)

    Mc Gaw, B.H.

    1984-01-01

    A machine for mining minerals is patented. It is a cutter loader with a drum actuating element of the worm type equipped with a multitude of cutting teeth reinforced with tungsten carbide. A feature of the patented machine is that all of the cutting teeth and holders on the drum have the identical design. This is achieved through selecting a slant angle for the cutting teeth which is the mean between the slant angle of the conventional radial teeth and the slant angle of the advance teeth. This, in turn, is provided thanks to the corresponding slant of the holders relative to the drum and (or) the slant of the cutting part of the teeth relative to their stems. Thus, the advance teeth projecting beyond the surface of the drum on the face side and providing upper and lateral clearances have the same angle of attack as the radial teeth, that is, from 20 to 35 degrees. A series of modifications of the cutting teeth is patented. One of the designs allows the cutting tooth to occupy a varying position relative to the drum, from the conventional vertical to an inverted, axially projecting position. In the last case the tooth in the extraction process provides the upper and lateral clearances for the drum on the face side. Among the different modifications of the cutting teeth, a design is proposed which provides for the presence of a stem which is shaped like a truncated cone. This particular stem is designed for use jointly with a wedge which unfastens the teeth and is placed in a holder. The latter is completed in a transverse slot thanks to which the rear end of the stem is compressed, which simplifies replacement of a tooth. Channels are provided in the patented machine for feeding water to the worm spiral, the holders and the cutting teeth themselves in order to deal with dust.

  6. Simulating Turing machines on Maurer machines

    NARCIS (Netherlands)

    Bergstra, J.A.; Middelburg, C.A.

    2008-01-01

    In a previous paper, we used Maurer machines to model and analyse micro-architectures. In the current paper, we investigate the connections between Turing machines and Maurer machines with the purpose to gain an insight into computability issues relating to Maurer machines. We introduce ways to

  7. Environmentally Friendly Machining

    CERN Document Server

    Dixit, U S; Davim, J Paulo

    2012-01-01

    Environment-Friendly Machining provides an in-depth overview of environmentally-friendly machining processes, covering numerous different types of machining in order to identify which practice is the most environmentally sustainable. The book discusses three systems at length: machining with minimal cutting fluid, air-cooled machining and dry machining. Also covered is a way to conserve energy during machining processes, along with useful data and detailed descriptions for developing and utilizing the most efficient modern machining tools. Researchers and engineers looking for sustainable machining solutions will find Environment-Friendly Machining to be a useful volume.

  8. Machine Transliteration

    CERN Document Server

    Knight, K; Knight, Kevin; Graehl, Jonathan

    1997-01-01

    It is challenging to translate names and technical terms across languages with different alphabets and sound inventories. These items are commonly transliterated, i.e., replaced with approximate phonetic equivalents. For example, "computer" in English comes out as "konpyuutaa" in Japanese. Translating such items from Japanese back to English is even more challenging, and of practical interest, as transliterated items make up the bulk of text phrases not found in bilingual dictionaries. We describe and evaluate a method for performing backwards transliterations by machine. This method uses a generative model, incorporating several distinct stages in the transliteration process.

  9. Shuttle requests

    CERN Multimedia

    2007-01-01

    Please note that, to improve the service we provide, a new telephone number - 72500 - has been set up for all shuttle requests concerning: journeys within the CERN site, i.e. official visits or bidders' conferences; journeys to or from the airport or city centre; long-distance journeys. However, it will still be possible to submit requests in writing to Fm.Support@cern. The radio taxi can also still be reached on 76969. The TS/FM group would also like to inform you that details of all light logistics services (transport of persons, distribution and collection of parcels up to 1 tonne, distribution and collection of mail) can be found on the group's website: http://ts-dep.web.cern.ch/ts-dep/groups/fm/fm.htm TS/FM Group 160239

  10. 一种利用电化学钝化极化现象的超深小孔电火花复合加工工艺%A New Electro-discharge Drilling Technique Based on Electrochemical Passivation Effect of Avoiding Side Discharge for Ultra Deep Micro Hole Machine-shaping

    Institute of Scientific and Technical Information of China (English)

    马名峻; 王德新

    2015-01-01

    通过对超深小孔电火花复合加工工艺的试验研究,研发了一种液体成膜的低浓度电解质环保水溶液,作为电火花高速小孔机专用工作液,用于超深小孔的电火花复合加工,成功解决了大深径比超深小孔的电火花加工工艺难题。而其中独具特点的“电极管平头低损耗”现象,也为解决诸如钨钼类高熔金属超深小孔及航空发动机叶片气膜孔加工等难题找到了一种新的工艺方法。%To drill the ultra deep micro hole by electrical-discharge machining technique ,mass of experiments were carried out with kinds of different technical approach. At last ,a new kind of appropriative working fluid was developed ,with which a layer of electrochemical passivation insulating film could be formed on the inner hole wall of the work piece to avoid side discharge ,the shape of the end of the electrode is flat instead of cone ,as a result. At the same time ,electrode loss was decreased significantly,based on which the efficiency of electrical-discharge drilling was improved. This kind of electrical-discharge machining working fluid could be applied for drilling deep hole on the tungsten molybdenum materials and manufacturing cooling film holes on aero engine blade.

  11. Machine Protection

    CERN Document Server

    Schmidt, R

    2014-01-01

    The protection of accelerator equipment is as old as accelerator technology and was for many years related to high-power equipment. Examples are the protection of powering equipment from overheating (magnets, power converters, high-current cables), of superconducting magnets from damage after a quench and of klystrons. The protection of equipment from beam accidents is more recent. It is related to the increasing beam power of high-power proton accelerators such as ISIS, SNS, ESS and the PSI cyclotron, to the emission of synchrotron light by electron–positron accelerators and FELs, and to the increase of energy stored in the beam (in particular for hadron colliders such as LHC). Designing a machine protection system requires an excellent understanding of accelerator physics and operation to anticipate possible failures that could lead to damage. Machine protection includes beam and equipment monitoring, a system to safely stop beam operation (e.g. dumping the beam or stopping the beam at low energy) and an ...

  12. Analysis of machining and machine tools

    CERN Document Server

    Liang, Steven Y

    2016-01-01

    This book delivers the fundamental science and mechanics of machining and machine tools by presenting systematic and quantitative knowledge in the form of process mechanics and physics. It gives readers a solid command of machining science and engineering, and familiarizes them with the geometry and functionality requirements of creating parts and components in today’s markets. The authors address traditional machining topics, such as: single and multiple point cutting processes grinding components accuracy and metrology shear stress in cutting cutting temperature and analysis chatter They also address non-traditional machining, such as: electrical discharge machining electrochemical machining laser and electron beam machining A chapter on biomedical machining is also included. This book is appropriate for advanced undergraduate and graduate mechani cal engineering students, manufacturing engineers, and researchers. Each chapter contains examples, exercises and their solutions, and homework problems that re...

  13. The Emerging Web of Social Machines

    CERN Document Server

    Meira, Silvio R L; Nascimento, Leandro M; de Figueiredo, Elaine G M; Neto, Misael; Encarnação, Bruno P; Garcia, Vinícius

    2010-01-01

    We define a notion of social machine and envisage an algebra that can describe networks of such. To start with, social machines are defined as tuples of input, output, processes, constraints, state, requests and responses; apart from defining the machines themselves, the algebra defines a set of connectors and conditionals that can be used to describe the interactions between any number of machines in a multitude of ways, as a means to represent real machines interacting in the real web, such as Twitter, Twitter running on top of Amazon AWS, mashups built using Twitter and, obviously, other social machines. This work is not a theoretical paper as yet; but, in more than one sense, we think we have found a way to describe web based information systems and are starting to work on what could be a practical way of dealing with the complexity of this emerging web of social machines that is all around us. This version should be read as work in progress and comments, observations, bugs... are most welcome and should ...

  14. Machine Readable Passports & The Visa Waiver Programme

    CERN Document Server

    2003-01-01

    From 1 October 2003, all passengers intending to enter the USA on the Visa Waiver Programme (VWP) will be required to present a machine-readable passport (MRP). Passengers travelling to the USA with a non-machine readable passport will require a valid US entry visa. Applying for a US visa is a lengthy process, which can take several weeks or even months. Therefore it is strongly recommended that: • All Visa Waiver nationals who hold a non-machine readable passport should obtain a MRP before their next visit to the USA. • Children travelling on a parent's passport (be it machine readable or non-machine readable) cannot benefit from the Visa Waiver Programme and should obtain their own MRP prior to travelling to the USA or request a visa. What is a Machine Readable Passport (MRP)? A MRP has the holders' personal details, e.g. name, date of birth, nationality and their passport number contained in two lines of text at the base of the photo page. This text may be read by machine. These 2 lines ...

  15. Side Effects (Management)

    Science.gov (United States)

    ... cancer care is relieving side effects, called symptom management, palliative care, or supportive care. It is important ... treat them. To learn about the symptoms and management of the long-term side effects of cancer ...

  16. Evaluating current processors performance and machines stability

    CERN Document Server

    Esposito, R; Tortone, G; Taurino, F M

    2003-01-01

    Accurately estimate performance of currently available processors is becoming a key activity, particularly in HENP environment, where high computing power is crucial. This document describes the methods and programs, opensource or freeware, used to benchmark processors, memory and disk subsystems and network connection architectures. These tools are also useful to stress test new machines, before their acquisition or before their introduction in a production environment, where high uptimes are requested.

  17. Electrical machines and assemblies including a yokeless stator with modular lamination stacks

    Energy Technology Data Exchange (ETDEWEB)

    Qu, Ronghai; Jansen, Patrick Lee; Bagepalli, Bharat Sampathkumar; Carl, Jr., Ralph James; Gadre, Aniruddha Dattatraya; Lopez, Fulton Jose

    2010-04-06

    An electrical machine includes a rotor with an inner rotor portion and an outer rotor portion, and a double-sided yokeless stator. The yokeless stator includes modular lamination stacks and is configured for radial magnetic flux flow. The double-sided yokeless stator is concentrically disposed between the inner rotor portion and the outer rotor portion of the electrical machine. Examples of particularly useful embodiments for the electrical machine include wind turbine generators, ship propulsion motors, switch reluctance machines and double-sided synchronous machines.

  18. Improved side information generation for distributed video coding

    DEFF Research Database (Denmark)

    Huang, Xin; Forchhammer, Søren

    2008-01-01

    information generation method, fewer bits will be requested from the encoder and more reliable decoded frames will be obtained. In this paper, a side information generation method is introduced to further improve the rate-distortion (RD) performance of transform domain distributed video coding. This algorithm......As a new coding paradigm, distributed video coding (DVC) deals with lossy source coding using side information to exploit the statistics at the decoder to reduce computational demands at the encoder. The performance of DVC highly depends on the quality of side information. With a better side...

  19. Automation of printing machine

    OpenAIRE

    Sušil, David

    2016-01-01

    Bachelor thesis is focused on the automation of the printing machine and comparing the two types of printing machines. The first chapter deals with the history of printing, typesettings, printing techniques and various kinds of bookbinding. The second chapter describes the difference between sheet-fed printing machines and offset printing machines, the difference between two representatives of rotary machines, technological process of the products on these machines, the description of the mac...

  20. Machine musicianship

    Science.gov (United States)

    Rowe, Robert

    2002-05-01

    The training of musicians begins by teaching basic musical concepts, a collection of knowledge commonly known as musicianship. Computer programs designed to implement musical skills (e.g., to make sense of what they hear, perform music expressively, or compose convincing pieces) can similarly benefit from access to a fundamental level of musicianship. Recent research in music cognition, artificial intelligence, and music theory has produced a repertoire of techniques that can make the behavior of computer programs more musical. Many of these were presented in a recently published book/CD-ROM entitled Machine Musicianship. For use in interactive music systems, we are interested in those which are fast enough to run in real time and that need only make reference to the material as it appears in sequence. This talk will review several applications that are able to identify the tonal center of musical material during performance. Beyond this specific task, the design of real-time algorithmic listening through the concurrent operation of several connected analyzers is examined. The presentation includes discussion of a library of C++ objects that can be combined to perform interactive listening and a demonstration of their capability.

  1. Compensation strategy for machining optical freeform surfaces by the combined on- and off-machine measurement.

    Science.gov (United States)

    Zhang, Xiaodong; Zeng, Zhen; Liu, Xianlei; Fang, Fengzhou

    2015-09-21

    Freeform surface is promising to be the next generation optics, however it needs high form accuracy for excellent performance. The closed-loop of fabrication-measurement-compensation is necessary for the improvement of the form accuracy. It is difficult to do an off-machine measurement during the freeform machining because the remounting inaccuracy can result in significant form deviations. On the other side, on-machine measurement may hides the systematic errors of the machine because the measuring device is placed in situ on the machine. This study proposes a new compensation strategy based on the combination of on-machine and off-machine measurement. The freeform surface is measured in off-machine mode with nanometric accuracy, and the on-machine probe achieves accurate relative position between the workpiece and machine after remounting. The compensation cutting path is generated according to the calculated relative position and shape errors to avoid employing extra manual adjustment or highly accurate reference-feature fixture. Experimental results verified the effectiveness of the proposed method.

  2. Electrical machines mathematical fundamentals of machine topologies

    CERN Document Server

    Gerling, Dieter

    2015-01-01

    Electrical Machines and Drives play a powerful role in industry with an ever increasing importance. This fact requires the understanding of machine and drive principles by engineers of many different disciplines. Therefore, this book is intended to give a comprehensive deduction of these principles. Special attention is given to the precise mathematical derivation of the necessary formulae to calculate machines and drives and to the discussion of simplifications (if applied) with the associated limits. The book shows how the different machine topologies can be deduced from general fundamentals, and how they are linked together. This book addresses graduate students, researchers, and developers of Electrical Machines and Drives, who are interested in getting knowledge about the principles of machine and drive operation and in detecting the mathematical and engineering specialties of the different machine and drive topologies together with their mutual links. The detailed - but nevertheless compact - mat...

  3. Laser machining of advanced materials

    CERN Document Server

    Dahotre, Narendra B

    2011-01-01

    Advanced materialsIntroductionApplicationsStructural ceramicsBiomaterials CompositesIntermetallicsMachining of advanced materials IntroductionFabrication techniquesMechanical machiningChemical Machining (CM)Electrical machiningRadiation machining Hybrid machiningLaser machiningIntroductionAbsorption of laser energy and multiple reflectionsThermal effectsLaser machining of structural ceramicsIntrodu

  4. The deleuzian abstract machines

    DEFF Research Database (Denmark)

    Werner Petersen, Erik

    2005-01-01

    production. In Kafka: Toward a Minor Literature, Deleuze and Guatari gave the most comprehensive explanation to the abstract machine in the work of art. Like the war-machines of Virilio, the Kafka-machine operates in three gears or speeds. Furthermore, the machine is connected to spatial diagrams...

  5. ANALYSIS OF DECREASE MACHINABILITY POSSIBLE CAUSES FOR CLAIMED ALLOY

    Directory of Open Access Journals (Sweden)

    Nataša Náprstková

    2016-09-01

    Full Text Available The Faculty of Production Technology and Management is often asked by companies with a request to solve a specific technical task. One of these tasks was the analysis of aluminum alloy worsened machinability when the rods from this alloy exhibited against assumption significantly worse (longer chips during machining. The alloy was complaint and, of course, it created economic damage. Obviously, the company was interested in the causes of this alloy behavior change that could possibly generate future complaints procedures to defend itself better, or to avoid mistakes in the production of the material. At the faculty analysis that could contribute to identifying the cause of the worsened machinability were done.

  6. Single-sided NMR

    CERN Document Server

    Casanova, Federico; Blümich, Bernhard

    2011-01-01

    Single-Sided NMR describes the design of the first functioning single-sided tomograph, the related measurement methods, and a number of applications. One of the key advantages to this method is the speed at which the images are obtained.

  7. One-sided arguments

    NARCIS (Netherlands)

    van Laar, J.A.

    2007-01-01

    When is an argument to be called one-sided? When is putting forward such an argument fallacious? How can we develop a model for critical discussion, such that a fallaciously one-sided argument corresponds to a violation of a discussion rule? These issues are dealt with within 'the limits of the dial

  8. Present status and prospects for vending machines; Jido hanbaiki no genjo to tenbo

    Energy Technology Data Exchange (ETDEWEB)

    Hirano, Y. [Fuji Denki Reiki Co. Ltd., Tokyo (Japan); Ota, T.; Iwamoto, S. [Fuji Electric Co. Ltd., Tokyo (Japan)

    1999-08-10

    The number of automatic vending and service machines installed in Japan at the end of 1998 is about 5.5 million. The number of units per head exceeds that of USA, a pioneer in vending machines. They are now playing an indispensable role in daily living. Recent needs of vending machines have increased in social requests or problems, such as (1) strengthening of crime prevention, (2) consideration of global ecology and (3) prevention of minors from using alcoholic drinks vending machines. This paper describes the current state of marketing and future prospects for vending machines. (author)

  9. GRINDING OF DOUBLE DISC GRINDING MACHINE

    Institute of Scientific and Technical Information of China (English)

    Hu Huiqing

    2005-01-01

    The grinding of two parallel sides of a component is accomplished with the accuracy and higher productivity by passing a blank through the truncated cone shape grinders, which are turned angles. The machine is designated by the name of double disc grinding machine (DDGM). Usually, it is used in the mass production. The relationship between these angles, the accuracy, productivity,allowance and parameters of the machine and technology is explained in detail by math, such as vector analysis, transformation of 3D space coordinates, etc. Therefore, in the aspects of qualitative and quantitative analyses, the grinding potential of DDGM is enormous increased and superior to conventional methods. Furthermore, the theoretical foundation of DDGM grinding design and technology is provided to improve, to expand and to create for future. The established machine design and practical experience of grinding technology will get great benefit by them.

  10. Machine tool structures

    CERN Document Server

    Koenigsberger, F

    1970-01-01

    Machine Tool Structures, Volume 1 deals with fundamental theories and calculation methods for machine tool structures. Experimental investigations into stiffness are discussed, along with the application of the results to the design of machine tool structures. Topics covered range from static and dynamic stiffness to chatter in metal cutting, stability in machine tools, and deformations of machine tool structures. This volume is divided into three sections and opens with a discussion on stiffness specifications and the effect of stiffness on the behavior of the machine under forced vibration c

  11. Troubleshooting Requests e-mail Confirmation

    CERN Multimedia

    TS Department

    2004-01-01

    In an ongoing effort to improve quality of the repair requests, a new e-mail confirmation automatic system will be implemented starting from the 21st October. All repair requests transmitted to the TCR (72201) or the FM Helpdesk (77777) will be confirmed in an e-mail to the requestor, provided that the latter has a valid e-mail address in the HR database. The e-mail will contain a reference number, a brief description of the problem, the location and a contact where more information can be obtained. A second e-mail will be sent when the processing of the repair request is finished. We hope that this initiative will improve the transparency and quality of our service. Helpdesk Troubleshooting Requests (reminder) We remind you that all the repair requests and other communication concerning the CERN machine buildings have to be transmitted to the TCR via 72201, whereas the ones concerning tertiary buildings are handled directly by the FM helpdesk under the phone number 77777, i.e. problems on systems and equ...

  12. Side Effects of Chemotherapy

    Science.gov (United States)

    ... Jacket Fashion Show Contact Us Side Effects of Chemotherapy Each of the chemotherapy drugs available today works in a slightly different ... few rules of thumb when it comes to chemotherapy that should always be kept in mind. Ignore ...

  13. Design of Demining Machines

    CERN Document Server

    Mikulic, Dinko

    2013-01-01

    In constant effort to eliminate mine danger, international mine action community has been developing safety, efficiency and cost-effectiveness of clearance methods. Demining machines have become necessary when conducting humanitarian demining where the mechanization of demining provides greater safety and productivity. Design of Demining Machines describes the development and testing of modern demining machines in humanitarian demining.   Relevant data for design of demining machines are included to explain the machinery implemented and some innovative and inspiring development solutions. Development technologies, companies and projects are discussed to provide a comprehensive estimate of the effects of various design factors and to proper selection of optimal parameters for designing the demining machines.   Covering the dynamic processes occurring in machine assemblies and their components to a broader understanding of demining machine as a whole, Design of Demining Machines is primarily tailored as a tex...

  14. Applied machining technology

    CERN Document Server

    Tschätsch, Heinz

    2010-01-01

    Machining and cutting technologies are still crucial for many manufacturing processes. This reference presents all important machining processes in a comprehensive and coherent way. It includes many examples of concrete calculations, problems and solutions.

  15. Machining with abrasives

    CERN Document Server

    Jackson, Mark J

    2011-01-01

    Abrasive machining is key to obtaining the desired geometry and surface quality in manufacturing. This book discusses the fundamentals and advances in the abrasive machining processes. It provides a complete overview of developing areas in the field.

  16. Women, Men, and Machines.

    Science.gov (United States)

    Form, William; McMillen, David Byron

    1983-01-01

    Data from the first national study of technological change show that proportionately more women than men operate machines, are more exposed to machines that have alienating effects, and suffer more from the negative effects of technological change. (Author/SSH)

  17. Machine medical ethics

    CERN Document Server

    Pontier, Matthijs

    2015-01-01

    The essays in this book, written by researchers from both humanities and sciences, describe various theoretical and experimental approaches to adding medical ethics to a machine in medical settings. Medical machines are in close proximity with human beings, and getting closer: with patients who are in vulnerable states of health, who have disabilities of various kinds, with the very young or very old, and with medical professionals. In such contexts, machines are undertaking important medical tasks that require emotional sensitivity, knowledge of medical codes, human dignity, and privacy. As machine technology advances, ethical concerns become more urgent: should medical machines be programmed to follow a code of medical ethics? What theory or theories should constrain medical machine conduct? What design features are required? Should machines share responsibility with humans for the ethical consequences of medical actions? How ought clinical relationships involving machines to be modeled? Is a capacity for e...

  18. Brain versus Machine Control.

    Directory of Open Access Journals (Sweden)

    Jose M Carmena

    2004-12-01

    Full Text Available Dr. Octopus, the villain of the movie "Spiderman 2", is a fusion of man and machine. Neuroscientist Jose Carmena examines the facts behind this fictional account of a brain- machine interface

  19. A Universal Reactive Machine

    DEFF Research Database (Denmark)

    Andersen, Henrik Reif; Mørk, Simon; Sørensen, Morten U.

    1997-01-01

    Turing showed the existence of a model universal for the set of Turing machines in the sense that given an encoding of any Turing machine asinput the universal Turing machine simulates it. We introduce the concept of universality for reactive systems and construct a CCS processuniversal...

  20. [Psychoanalysis and Side Effect].

    Science.gov (United States)

    Shirahase, Joichiro

    2015-01-01

    A study of psychoanalysis from the perspective of side effects reveals that its history was a succession of measures to deal with its own side effects. This, however, does not merely suggest that, as a treatment method, psychoanalysis is incomplete and weak: rather, its history is a record of the growth and development of psychoanalysis that discovered therapeutic significance from phenomena that were initially regarded as side effects, made use of these discoveries, and elaborated them as a treatment method. The approach of research seen during the course of these developments is linked to the basic therapeutic approach of psychoanalysis. A therapist therefore does not draw conclusions about a patient's words and behaviors from a single aspect, but continues to make efforts to actively discover a variety of meanings and values from them, and to make the patient's life richer and more productive. This therapeutic approach is undoubtedly one of the unique aspects of psychoanalysis. I discuss the issue of psychoanalysis and side effects with the aim of clarifying this unique characteristic of psychoanalysis. The phenomenon called resistance inevitably emerges during the process of psychoanalytic treatment. Resistance can not only obstruct the progress of therapy; it also carries the risk of causing a variety of disadvantages to the patient. It can therefore be seen as an adverse effect. However, if we re-examine this phenomenon from the perspective of transference, we find that resistance is in fact a crucial tool in psychoanalysis, and included in its main effect, rather than a side effect. From the perspective of minimizing the character of resistance as a side effect and maximizing its character as a main effect, I have reviewed logical organization, dynamic evaluation, the structuring of treatment, the therapist's attitudes, and the training of therapists. I conclude by stating that psychoanalysis has aspects that do not match the perspective known as a side

  1. Asynchronized synchronous machines

    CERN Document Server

    Botvinnik, M M

    1964-01-01

    Asynchronized Synchronous Machines focuses on the theoretical research on asynchronized synchronous (AS) machines, which are "hybrids” of synchronous and induction machines that can operate with slip. Topics covered in this book include the initial equations; vector diagram of an AS machine; regulation in cases of deviation from the law of full compensation; parameters of the excitation system; and schematic diagram of an excitation regulator. The possible applications of AS machines and its calculations in certain cases are also discussed. This publication is beneficial for students and indiv

  2. Quantum machine learning.

    Science.gov (United States)

    Biamonte, Jacob; Wittek, Peter; Pancotti, Nicola; Rebentrost, Patrick; Wiebe, Nathan; Lloyd, Seth

    2017-09-13

    Fuelled by increasing computer power and algorithmic advances, machine learning techniques have become powerful tools for finding patterns in data. Quantum systems produce atypical patterns that classical systems are thought not to produce efficiently, so it is reasonable to postulate that quantum computers may outperform classical computers on machine learning tasks. The field of quantum machine learning explores how to devise and implement quantum software that could enable machine learning that is faster than that of classical computers. Recent work has produced quantum algorithms that could act as the building blocks of machine learning programs, but the hardware and software challenges are still considerable.

  3. Precision machine design

    CERN Document Server

    Slocum, Alexander H

    1992-01-01

    This book is a comprehensive engineering exploration of all the aspects of precision machine design - both component and system design considerations for precision machines. It addresses both theoretical analysis and practical implementation providing many real-world design case studies as well as numerous examples of existing components and their characteristics. Fast becoming a classic, this book includes examples of analysis techniques, along with the philosophy of the solution method. It explores the physics of errors in machines and how such knowledge can be used to build an error budget for a machine, how error budgets can be used to design more accurate machines.

  4. Working the Dark Side

    DEFF Research Database (Denmark)

    Bjering, Jens Christian Borrebye

    A few days after the terror attacks of 9/11, then Vice President Dick Cheney appeared on television with a call for “working the dark side.” While still unclear what this expression entailed at the time, Cheney's comment appears in retrospect to almost have been prophetic for the years to come....... By analyzing official reports and testimonies from soldiers partaking in the War On Terror, the dissertation's second part—dark arts—focuses on the transformation of the dark side into a productive space in which “information” and the hunt for said information overshadowed all legal, ethical, or political...

  5. Working the Dark Side

    DEFF Research Database (Denmark)

    Bjering, Jens Christian Borrebye

    half—dark side—documents the making and nature of the dark side by analyzing a series of legal memos from the Department of Justice's Office of Legal Council and from the White House and concludes by relating its findings to traditional ideas about emergency action, national security, and torture....... By analyzing official reports and testimonies from soldiers partaking in the War On Terror, the dissertation's second part—dark arts—focuses on the transformation of the dark side into a productive space in which “information” and the hunt for said information overshadowed all legal, ethical, or political...

  6. Design and Application on Auto-vending Machine for Cupped Beverage

    Directory of Open Access Journals (Sweden)

    Xiaowei Jiang

    2014-12-01

    Full Text Available The purpose of this study is to design an auto-vending machine for cupped beverage, specifically studying its shape design and color design. The article elaborates that the shape design of this auto-vending machine for cupped beverage should follow the art rule of variation and unity and meanwhile the whole shape still should be simple and direct; the color design of the auto-vending machine for cupped beverage not only should satisfy the request of man-machine coordination and environment and function, but also should value the choice of tone, match the new age request of appreciation beauty and notice novelty. And then the working principle and working process of the auto-vending machine for cupped beverage is introduced, based on which the conclusion has been reached.

  7. Perspex machine: VII. The universal perspex machine

    Science.gov (United States)

    Anderson, James A. D. W.

    2006-01-01

    The perspex machine arose from the unification of projective geometry with the Turing machine. It uses a total arithmetic, called transreal arithmetic, that contains real arithmetic and allows division by zero. Transreal arithmetic is redefined here. The new arithmetic has both a positive and a negative infinity which lie at the extremes of the number line, and a number nullity that lies off the number line. We prove that nullity, 0/0, is a number. Hence a number may have one of four signs: negative, zero, positive, or nullity. It is, therefore, impossible to encode the sign of a number in one bit, as floating-point arithmetic attempts to do, resulting in the difficulty of having both positive and negative zeros and NaNs. Transrational arithmetic is consistent with Cantor arithmetic. In an extension to real arithmetic, the product of zero, an infinity, or nullity with its reciprocal is nullity, not unity. This avoids the usual contradictions that follow from allowing division by zero. Transreal arithmetic has a fixed algebraic structure and does not admit options as IEEE, floating-point arithmetic does. Most significantly, nullity has a simple semantics that is related to zero. Zero means "no value" and nullity means "no information." We argue that nullity is as useful to a manufactured computer as zero is to a human computer. The perspex machine is intended to offer one solution to the mind-body problem by showing how the computable aspects of mind and, perhaps, the whole of mind relates to the geometrical aspects of body and, perhaps, the whole of body. We review some of Turing's writings and show that he held the view that his machine has spatial properties. In particular, that it has the property of being a 7D lattice of compact spaces. Thus, we read Turing as believing that his machine relates computation to geometrical bodies. We simplify the perspex machine by substituting an augmented Euclidean geometry for projective geometry. This leads to a general

  8. Four Sided Seal Tester

    Science.gov (United States)

    2009-07-01

    The Center for Advanced Food Technology School of Enviromental and Biological Sciences New Brunswick, NJ 08903 FTR 216 Defense Logistics Agency...specification for four sided seal tester as function of confinement plate distance” The following modifications were issued :  Jul 18, 2007 0013/01

  9. Colorectal cancers choosing sides

    NARCIS (Netherlands)

    Albuquerque, Cristina; Bakker, Elvira R. M.; van Veelen, Wendy; Smits, Ron

    2011-01-01

    In contrast to the majority of sporadic colorectal cancer which predominantly occur in the distal colon, most mismatch repair deficient tumours arise at the proximal side. At present, these regional preferences have not been explained properly. Recently, we have screened colorectal tumours for mutat

  10. Side effects of ergotamine

    NARCIS (Netherlands)

    Meyler, WJ

    1996-01-01

    Ergotamine has been used for many years in the treatment of migraine, although there is Little formal clinical evidence that it is significantly more efficacious than placebo. A number of side effects associated with ergotamine have been reported in the literature, including myocardial infarction, i

  11. Simulation of machine interference in randomly changing environments

    Directory of Open Access Journals (Sweden)

    Sztrik J.

    2002-01-01

    Full Text Available The simulation tool lcpSim can be used to investigate special level crossing problems of queuing systems of type HYPOk / HYPOr / 1 // n embedded in different Markovian environments (recently referred to as Markov modulated ones. Our observed system consists of n heterogeneous machines (requests and a server that 'repairs' the broken machines according to the most commonly used service disciplines, such as FIFO, LIFO, PPS, HOL, Preemptive Priorities (Resume, Repeat, Transfer, Polling, Nearest. We specify a maximum number of stopped machines for an operating system and our aim is to give the main steady-state performance measures of the system, such as, server utilization, machine utilization, mean waiting times, mean response times, the probability of an operating system and the mean operating time of the system. These values can be calculated by lcpSim level crossing problem Simulation package for different random environment types and service disciplines.

  12. SHIPPING REQUESTS ON EDH

    CERN Multimedia

    Logistics Group

    2001-01-01

    Users are informed that as from 1 September 2001 all Shipping Requests must be made on EDH using the appropriate electronic form. The submission of user requests directly into EDH will help rationalise the activities of the Shipping Service (Import & Export), with requests being automatically forwarded to hierarchical supervisors thereby improving the processing speed and facilitating the follow-up. Thank you for your collaboration.

  13. SHIPPING REQUESTS ON EDH

    CERN Multimedia

    Logistics Group

    2001-01-01

    Users are informed that as from 1 September 2001 all Shipping Requests must be made on EDH using the appropriate electronic form. The submission of user requests directly into EDH will help rationalise the activities of the Shipping Service (Import & Export), with requests being automatically forwarded to hierarchical supervisors thereby improving the processing speed and facilitating the follow-up. Thank you for your collaboration.

  14. Machinability of advanced materials

    CERN Document Server

    Davim, J Paulo

    2014-01-01

    Machinability of Advanced Materials addresses the level of difficulty involved in machining a material, or multiple materials, with the appropriate tooling and cutting parameters.  A variety of factors determine a material's machinability, including tool life rate, cutting forces and power consumption, surface integrity, limiting rate of metal removal, and chip shape. These topics, among others, and multiple examples comprise this research resource for engineering students, academics, and practitioners.

  15. Pattern recognition & machine learning

    CERN Document Server

    Anzai, Y

    1992-01-01

    This is the first text to provide a unified and self-contained introduction to visual pattern recognition and machine learning. It is useful as a general introduction to artifical intelligence and knowledge engineering, and no previous knowledge of pattern recognition or machine learning is necessary. Basic for various pattern recognition and machine learning methods. Translated from Japanese, the book also features chapter exercises, keywords, and summaries.

  16. Support vector machines applications

    CERN Document Server

    Guo, Guodong

    2014-01-01

    Support vector machines (SVM) have both a solid mathematical background and good performance in practical applications. This book focuses on the recent advances and applications of the SVM in different areas, such as image processing, medical practice, computer vision, pattern recognition, machine learning, applied statistics, business intelligence, and artificial intelligence. The aim of this book is to create a comprehensive source on support vector machine applications, especially some recent advances.

  17. Machining of titanium alloys

    CERN Document Server

    2014-01-01

    This book presents a collection of examples illustrating the resent research advances in the machining of titanium alloys. These materials have excellent strength and fracture toughness as well as low density and good corrosion resistance; however, machinability is still poor due to their low thermal conductivity and high chemical reactivity with cutting tool materials. This book presents solutions to enhance machinability in titanium-based alloys and serves as a useful reference to professionals and researchers in aerospace, automotive and biomedical fields.

  18. Rotating electrical machines

    CERN Document Server

    Le Doeuff, René

    2013-01-01

    In this book a general matrix-based approach to modeling electrical machines is promulgated. The model uses instantaneous quantities for key variables and enables the user to easily take into account associations between rotating machines and static converters (such as in variable speed drives).   General equations of electromechanical energy conversion are established early in the treatment of the topic and then applied to synchronous, induction and DC machines. The primary characteristics of these machines are established for steady state behavior as well as for variable speed scenarios. I

  19. Chaotic Boltzmann machines.

    Science.gov (United States)

    Suzuki, Hideyuki; Imura, Jun-ichi; Horio, Yoshihiko; Aihara, Kazuyuki

    2013-01-01

    The chaotic Boltzmann machine proposed in this paper is a chaotic pseudo-billiard system that works as a Boltzmann machine. Chaotic Boltzmann machines are shown numerically to have computing abilities comparable to conventional (stochastic) Boltzmann machines. Since no randomness is required, efficient hardware implementation is expected. Moreover, the ferromagnetic phase transition of the Ising model is shown to be characterised by the largest Lyapunov exponent of the proposed system. In general, a method to relate probabilistic models to nonlinear dynamics by derandomising Gibbs sampling is presented.

  20. Tribology in machine design

    CERN Document Server

    Stolarski, Tadeusz

    1999-01-01

    ""Tribology in Machine Design is strongly recommended for machine designers, and engineers and scientists interested in tribology. It should be in the engineering library of companies producing mechanical equipment.""Applied Mechanics ReviewTribology in Machine Design explains the role of tribology in the design of machine elements. It shows how algorithms developed from the basic principles of tribology can be used in a range of practical applications within mechanical devices and systems.The computer offers today's designer the possibility of greater stringen

  1. Debugging the virtual machine

    Energy Technology Data Exchange (ETDEWEB)

    Miller, P.; Pizzi, R.

    1994-09-02

    A computer program is really nothing more than a virtual machine built to perform a task. The program`s source code expresses abstract constructs using low level language features. When a virtual machine breaks, it can be very difficult to debug because typical debuggers provide only low level machine implementation in formation to the software engineer. We believe that the debugging task can be simplified by introducing aspects of the abstract design into the source code. We introduce OODIE, an object-oriented language extension that allows programmers to specify a virtual debugging environment which includes the design and abstract data types of the virtual machine.

  2. Electrical machines & drives

    CERN Document Server

    Hammond, P

    1985-01-01

    Containing approximately 200 problems (100 worked), the text covers a wide range of topics concerning electrical machines, placing particular emphasis upon electrical-machine drive applications. The theory is concisely reviewed and focuses on features common to all machine types. The problems are arranged in order of increasing levels of complexity and discussions of the solutions are included where appropriate to illustrate the engineering implications. This second edition includes an important new chapter on mathematical and computer simulation of machine systems and revised discussions o

  3. Machine learning with R

    CERN Document Server

    Lantz, Brett

    2013-01-01

    Written as a tutorial to explore and understand the power of R for machine learning. This practical guide that covers all of the need to know topics in a very systematic way. For each machine learning approach, each step in the process is detailed, from preparing the data for analysis to evaluating the results. These steps will build the knowledge you need to apply them to your own data science tasks.Intended for those who want to learn how to use R's machine learning capabilities and gain insight from your data. Perhaps you already know a bit about machine learning, but have never used R; or

  4. Induction machine handbook

    CERN Document Server

    Boldea, Ion

    2002-01-01

    Often called the workhorse of industry, the advent of power electronics and advances in digital control are transforming the induction motor into the racehorse of industrial motion control. Now, the classic texts on induction machines are nearly three decades old, while more recent books on electric motors lack the necessary depth and detail on induction machines.The Induction Machine Handbook fills industry's long-standing need for a comprehensive treatise embracing the many intricate facets of induction machine analysis and design. Moving gradually from simple to complex and from standard to

  5. SEAMLESS TECHNOLOGY ON CIRCULAR KNITTING MACHINES

    OpenAIRE

    CRETU Viorica

    2014-01-01

    With industrial progress, the advancements in garment manufacturing have evolved from cut & sew to complete garment knitting, which produces one entire garment without sewing or linking process. Seamless knitting technology is similar to sock manufacture, the specialized circular knitting machines producing 3 dimensional garments with no side seams, with the waistband integrated with body of the garment and with knitted washing instructions and logos. The paper starts by presenting the main a...

  6. Virtual machine vs Real Machine: Security Systems

    Directory of Open Access Journals (Sweden)

    Dr. C. Suresh Gnana Das

    2009-08-01

    Full Text Available This paper argues that the operating system and applications currently running on a real machine should relocate into a virtual machine. This structure enables services to be added below the operating system and to do so without trusting or modifying the operating system or applications. To demonstrate the usefulness of this structure, we describe three services that take advantage of it: secure logging, intrusion prevention and detection, and environment migration. In particular, we can provide services below the guest operating system without trusting or modifying it. We believe providing services at this layer are especially useful for enhancing security and mobility. This position paper describes the general benefits and challenges that arise from running most applications in a virtual machine, and then describes some example services and alternative ways to provide those services.

  7. ADVANCED DESIGN SOLUTIONS FOR HIGH-PRECISION WOODWORKING MACHINES

    Directory of Open Access Journals (Sweden)

    Giuseppe Lucisano

    2016-03-01

    Full Text Available With the aim at performing the highest precision during woodworking, a mix of alternative approaches, fruitfully integrated in a common design strategy, is essential. This paper represents an overview of technical solutions, recently developed by authors, in design of machine tools and their final effects on manufacturing. The most advanced solutions in machine design are reported side by side with common practices or little everyday expedients. These design actions are directly or indirectly related to the rational use of materials, sometimes very uncommon, as in the case of magnetorheological fluids chosen to implement an active control in speed and force on the electro-spindle, and permitting to improve the quality of wood machining. Other actions are less unusual, as in the case of the adoption of innovative anti-vibration supports for basement. Tradition or innovation, all these technical solutions contribute to the final result: the highest precision in wood machining.

  8. Stirling machine operating experience

    Energy Technology Data Exchange (ETDEWEB)

    Ross, B. [Stirling Technology Co., Richland, WA (United States); Dudenhoefer, J.E. [Lewis Research Center, Cleveland, OH (United States)

    1994-09-01

    Numerous Stirling machines have been built and operated, but the operating experience of these machines is not well known. It is important to examine this operating experience in detail, because it largely substantiates the claim that stirling machines are capable of reliable and lengthy operating lives. The amount of data that exists is impressive, considering that many of the machines that have been built are developmental machines intended to show proof of concept, and are not expected to operate for lengthy periods of time. Some Stirling machines (typically free-piston machines) achieve long life through non-contact bearings, while other Stirling machines (typically kinematic) have achieved long operating lives through regular seal and bearing replacements. In addition to engine and system testing, life testing of critical components is also considered. The record in this paper is not complete, due to the reluctance of some organizations to release operational data and because several organizations were not contacted. The authors intend to repeat this assessment in three years, hoping for even greater participation.

  9. Perpetual Motion Machine

    Directory of Open Access Journals (Sweden)

    D. Tsaousis

    2008-01-01

    Full Text Available Ever since the first century A.D. there have been relative descriptions of known devices as well as manufactures for the creation of perpetual motion machines. Although physics has led, with two thermodynamic laws, to the opinion that a perpetual motion machine is impossible to be manufactured, inventors of every age and educational level appear to claim that they have invented something «entirely new» or they have improved somebody else’s invention, which «will function henceforth perpetually»! However the fact of the failure in manufacturing a perpetual motion machine till now, it does not mean that countless historical elements for these fictional machines become indifferent. The discussion on every version of a perpetual motion machine on the one hand gives the chance to comprehend the inventor’s of each period level of knowledge and his way of thinking, and on the other hand, to locate the points where this «perpetual motion machine» clashes with the laws of nature and that’s why it is impossible to have been manufactured or have functioned. The presentation of a new «perpetual motion machine» has excited our interest to locate its weak points. According to the designer of it the machine functions with the work produced by the buoyant force

  10. Machine Intelligence and Explication

    NARCIS (Netherlands)

    Wieringa, Roelf J.

    1987-01-01

    This report is an MA ("doctoraal") thesis submitted to the department of philosophy, university of Amsterdam. It attempts to answer the question whether machines can think by conceptual analysis. Ideally. a conceptual analysis should give plausible explications of the concepts of "machine" and "inte

  11. Microsoft Azure machine learning

    CERN Document Server

    Mund, Sumit

    2015-01-01

    The book is intended for those who want to learn how to use Azure Machine Learning. Perhaps you already know a bit about Machine Learning, but have never used ML Studio in Azure; or perhaps you are an absolute newbie. In either case, this book will get you up-and-running quickly.

  12. Reactive Turing machines

    NARCIS (Netherlands)

    Baeten, J.C.M.; Luttik, B.; Tilburg, P.J.A. van

    2013-01-01

    We propose reactive Turing machines (RTMs), extending classical Turing machines with a process-theoretical notion of interaction, and use it to define a notion of executable transition system. We show that every computable transition system with a bounded branching degree is simulated modulo diverge

  13. Machine Intelligence and Explication

    NARCIS (Netherlands)

    Wieringa, Roel

    1987-01-01

    This report is an MA ("doctoraal") thesis submitted to the department of philosophy, university of Amsterdam. It attempts to answer the question whether machines can think by conceptual analysis. Ideally. a conceptual analysis should give plausible explications of the concepts of "machine" and "inte

  14. Coordinate measuring machines

    DEFF Research Database (Denmark)

    De Chiffre, Leonardo

    This document is used in connection with three exercises of 2 hours duration as a part of the course GEOMETRICAL METROLOGY AND MACHINE TESTING. The exercises concern three aspects of coordinate measuring: 1) Measuring and verification of tolerances on coordinate measuring machines, 2) Traceability...

  15. Simple Machine Junk Cars

    Science.gov (United States)

    Herald, Christine

    2010-01-01

    During the month of May, the author's eighth-grade physical science students study the six simple machines through hands-on activities, reading assignments, videos, and notes. At the end of the month, they can easily identify the six types of simple machine: inclined plane, wheel and axle, pulley, screw, wedge, and lever. To conclude this unit,…

  16. Human Machine Learning Symbiosis

    Science.gov (United States)

    Walsh, Kenneth R.; Hoque, Md Tamjidul; Williams, Kim H.

    2017-01-01

    Human Machine Learning Symbiosis is a cooperative system where both the human learner and the machine learner learn from each other to create an effective and efficient learning environment adapted to the needs of the human learner. Such a system can be used in online learning modules so that the modules adapt to each learner's learning state both…

  17. Machine learning with R

    CERN Document Server

    Lantz, Brett

    2015-01-01

    Perhaps you already know a bit about machine learning but have never used R, or perhaps you know a little R but are new to machine learning. In either case, this book will get you up and running quickly. It would be helpful to have a bit of familiarity with basic programming concepts, but no prior experience is required.

  18. 15 CFR 700.31 - Metalworking machines.

    Science.gov (United States)

    2010-01-01

    ... Drilling and tapping machines Electrical discharge, ultrasonic and chemical erosion machines Forging..., power driven Machining centers and way-type machines Manual presses Mechanical presses, power...

  19. LHC Report: machine development

    CERN Multimedia

    Rogelio Tomás García for the LHC team

    2015-01-01

    Machine development weeks are carefully planned in the LHC operation schedule to optimise and further study the performance of the machine. The first machine development session of Run 2 ended on Saturday, 25 July. Despite various hiccoughs, it allowed the operators to make great strides towards improving the long-term performance of the LHC.   The main goals of this first machine development (MD) week were to determine the minimum beam-spot size at the interaction points given existing optics and collimation constraints; to test new beam instrumentation; to evaluate the effectiveness of performing part of the beam-squeezing process during the energy ramp; and to explore the limits on the number of protons per bunch arising from the electromagnetic interactions with the accelerator environment and the other beam. Unfortunately, a series of events reduced the machine availability for studies to about 50%. The most critical issue was the recurrent trip of a sextupolar corrector circuit –...

  20. Micro-machining.

    Science.gov (United States)

    Brinksmeier, Ekkard; Preuss, Werner

    2012-08-28

    Manipulating bulk material at the atomic level is considered to be the domain of physics, chemistry and nanotechnology. However, precision engineering, especially micro-machining, has become a powerful tool for controlling the surface properties and sub-surface integrity of the optical, electronic and mechanical functional parts in a regime where continuum mechanics is left behind and the quantum nature of matter comes into play. The surprising subtlety of micro-machining results from the extraordinary precision of tools, machines and controls expanding into the nanometre range-a hundred times more precise than the wavelength of light. In this paper, we will outline the development of precision engineering, highlight modern achievements of ultra-precision machining and discuss the necessity of a deeper physical understanding of micro-machining.

  1. Introduction to machine learning.

    Science.gov (United States)

    Baştanlar, Yalin; Ozuysal, Mustafa

    2014-01-01

    The machine learning field, which can be briefly defined as enabling computers make successful predictions using past experiences, has exhibited an impressive development recently with the help of the rapid increase in the storage capacity and processing power of computers. Together with many other disciplines, machine learning methods have been widely employed in bioinformatics. The difficulties and cost of biological analyses have led to the development of sophisticated machine learning approaches for this application area. In this chapter, we first review the fundamental concepts of machine learning such as feature assessment, unsupervised versus supervised learning and types of classification. Then, we point out the main issues of designing machine learning experiments and their performance evaluation. Finally, we introduce some supervised learning methods.

  2. Putting the Side first

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-01

    SIDE Minerals is a relative newcomer to the South African mining industry. It combines coal and anthracite mining and has base and precious metal interests. Side Minerals has offices in Boksburg from where its mining operations in Delmas, Witbank and Carolina in the Eastern Transvaal, and Newcastle in Natal are controlled. Lakeside Colliery at Witbank -a mine with a life expectancy of 15 years - is both an underground and opencast operation with an annual production capacity of 1,2 Mt of high, medium and low grade coal. Opencast extraction there is by the strip mining method. This is done on contract by Concor Mining Opencast Division, a member of the Concor Holding Group. A high wall face provides entry to the underground operations. Eastside Colliery at Carolina, which has the capacity to produce 480 000 tons of coal a year, is currently an opencast operation with underground mining scheduled to begin during 1994. Westside Colliery near Delmas is on a care and maintenance basis, but it has the capacity to produce 600 000 tons of low grade phosphorous coal which is required by the ferro-alloy and steel industries. 2 figs.

  3. Variable-Speed, Robust Synchronous Reluctance Machine Drive Systems

    DEFF Research Database (Denmark)

    Wang, Dong

    The synchronous reluctance machine drive is getting more and more interests from the industrial side, since it can provide higher system energy efficiency than traditional inverter-fed induction machine drive systems with similar production cost. It is considered as a good candidate for super...... premium efficiency machine and commercial products are available in the market. The research work in this dissertation aims at developing a simple, compact and robust synchronous reluctance machine drive system that can provide satisfactory performance with optimized system energy efficiency at various...... working conditions. Field oriented control assisted with various position estimation algorithms is in-vestigated. Position sensing via machine flux linkage is implemented with the assistance of a widely used flux observer. Experiments show that it may not always work properly and system oscillation...

  4. Traction sheave elevator, hoisting unit and machine space

    Science.gov (United States)

    Hakala, Harri; Mustalahti, Jorma; Aulanko, Esko

    2000-01-01

    Traction sheave elevator consisting of an elevator car moving along elevator guide rails, a counterweight moving along counterweight guide rails, a set of hoisting ropes (3) on which the elevator car and counterweight are suspended, and a drive machine unit (6) driving a traction sheave (7) acting on the hoisting ropes (3) and placed in the elevator shaft. The drive machine unit (6) is of a flat construction. A wall of the elevator shaft is provided with a machine space with its open side facing towards the shaft, the essential parts of the drive machine unit (6) being placed in the space. The hoisting unit (9) of the traction sheave elevator consists of a substantially discoidal drive machine unit (6) and an instrument panel (8) mounted on the frame (20) of the hoisting unit.

  5. Machine Learning and Radiology

    Science.gov (United States)

    Wang, Shijun; Summers, Ronald M.

    2012-01-01

    In this paper, we give a short introduction to machine learning and survey its applications in radiology. We focused on six categories of applications in radiology: medical image segmentation, registration, computer aided detection and diagnosis, brain function or activity analysis and neurological disease diagnosis from fMR images, content-based image retrieval systems for CT or MRI images, and text analysis of radiology reports using natural language processing (NLP) and natural language understanding (NLU). This survey shows that machine learning plays a key role in many radiology applications. Machine learning identifies complex patterns automatically and helps radiologists make intelligent decisions on radiology data such as conventional radiographs, CT, MRI, and PET images and radiology reports. In many applications, the performance of machine learning-based automatic detection and diagnosis systems has shown to be comparable to that of a well-trained and experienced radiologist. Technology development in machine learning and radiology will benefit from each other in the long run. Key contributions and common characteristics of machine learning techniques in radiology are discussed. We also discuss the problem of translating machine learning applications to the radiology clinical setting, including advantages and potential barriers. PMID:22465077

  6. The basic anaesthesia machine.

    Science.gov (United States)

    Gurudatt, Cl

    2013-09-01

    After WTG Morton's first public demonstration in 1846 of use of ether as an anaesthetic agent, for many years anaesthesiologists did not require a machine to deliver anaesthesia to the patients. After the introduction of oxygen and nitrous oxide in the form of compressed gases in cylinders, there was a necessity for mounting these cylinders on a metal frame. This stimulated many people to attempt to construct the anaesthesia machine. HEG Boyle in the year 1917 modified the Gwathmey's machine and this became popular as Boyle anaesthesia machine. Though a lot of changes have been made for the original Boyle machine still the basic structure remains the same. All the subsequent changes which have been brought are mainly to improve the safety of the patients. Knowing the details of the basic machine will make the trainee to understand the additional improvements. It is also important for every practicing anaesthesiologist to have a thorough knowledge of the basic anaesthesia machine for safe conduct of anaesthesia.

  7. The basic anaesthesia machine

    Directory of Open Access Journals (Sweden)

    C L Gurudatt

    2013-01-01

    Full Text Available After WTG Morton′s first public demonstration in 1846 of use of ether as an anaesthetic agent, for many years anaesthesiologists did not require a machine to deliver anaesthesia to the patients. After the introduction of oxygen and nitrous oxide in the form of compressed gases in cylinders, there was a necessity for mounting these cylinders on a metal frame. This stimulated many people to attempt to construct the anaesthesia machine. HEG Boyle in the year 1917 modified the Gwathmey′s machine and this became popular as Boyle anaesthesia machine. Though a lot of changes have been made for the original Boyle machine still the basic structure remains the same. All the subsequent changes which have been brought are mainly to improve the safety of the patients. Knowing the details of the basic machine will make the trainee to understand the additional improvements. It is also important for every practicing anaesthesiologist to have a thorough knowledge of the basic anaesthesia machine for safe conduct of anaesthesia.

  8. ANALYSIS OF PARAMETERS AFFECTING THE QUALITY OF A CUTTING MACHINE

    Directory of Open Access Journals (Sweden)

    Iveta Onderová

    2014-02-01

    Full Text Available The quality of cutting machines is affected by several factors that can be directly or indirectly influenced by manufacturers, technicians and users of machine tools. The most critical qualitative evaluation parameters of machine tools include accuracy and stability. Investigations of accuracy and repeatable positioning accuracy were essential for the research presented in this paper. The aim was to develop and experimentally verify the design of a methodology for cutting centers aimed at achieving the desired working precision. Before working on the topic described here, it was necessary to make several scientific analyses, which are summarized in this paper. We can build on the initial working hypothesis that by improving the technological parameters (e.g. by increasing the working speed of the machine, or by improving the precision of the positioning the quality of the cutting machine will also be improved. For the purposes of our study, several investigated parameters were set affecting positioning accuracy, such as rigidity, positioning speed, etc. First, the stiffness of the portal structure of the cutting machine was analyzed. FEM analysis was used to investigate several alternative structures of the cutting machine, and also an innovative solution for beam mounting. The second step was to integrate two types of drives into the design of the cutting machine. The first drive is a classic rack and pinion drive for cutting machines. To increase (improve the working speed of the machine, linear motors were designed as an alternative drive. The portal of the cutting machine was designed for a working speed of 260mmin−1 and acceleration of 25 m. s−2. The third step was based on the results of the analysis. In collaboration with Microstep, an experimental cutting machine in a portal version was produced using linear synchronous motors driving the portal on both sides, and with direct linear metering of its position. In the fourth step, an

  9. Fundamentals of machine design

    CERN Document Server

    Karaszewski, Waldemar

    2011-01-01

    A forum of researchers, educators and engineers involved in various aspects of Machine Design provided the inspiration for this collection of peer-reviewed papers. The resultant dissemination of the latest research results, and the exchange of views concerning the future research directions to be taken in this field will make the work of immense value to all those having an interest in the topics covered. The book reflects the cooperative efforts made in seeking out the best strategies for effecting improvements in the quality and the reliability of machines and machine parts and for extending

  10. Machine Tool Software

    Science.gov (United States)

    1988-01-01

    A NASA-developed software package has played a part in technical education of students who major in Mechanical Engineering Technology at William Rainey Harper College. Professor Hack has been using (APT) Automatically Programmed Tool Software since 1969 in his CAD/CAM Computer Aided Design and Manufacturing curriculum. Professor Hack teaches the use of APT programming languages for control of metal cutting machines. Machine tool instructions are geometry definitions written in APT Language to constitute a "part program." The part program is processed by the machine tool. CAD/CAM students go from writing a program to cutting steel in the course of a semester.

  11. Analysis of synchronous machines

    CERN Document Server

    Lipo, TA

    2012-01-01

    Analysis of Synchronous Machines, Second Edition is a thoroughly modern treatment of an old subject. Courses generally teach about synchronous machines by introducing the steady-state per phase equivalent circuit without a clear, thorough presentation of the source of this circuit representation, which is a crucial aspect. Taking a different approach, this book provides a deeper understanding of complex electromechanical drives. Focusing on the terminal rather than on the internal characteristics of machines, the book begins with the general concept of winding functions, describing the placeme

  12. Database machine performance

    Energy Technology Data Exchange (ETDEWEB)

    Cesarini, F.; Salza, S.

    1987-01-01

    This book is devoted to the important problem of database machine performance evaluation. The book presents several methodological proposals and case studies, that have been developed within an international project supported by the European Economic Community on Database Machine Evaluation Techniques and Tools in the Context of the Real Time Processing. The book gives an overall view of the modeling methodologies and the evaluation strategies that can be adopted to analyze the performance of the database machine. Moreover, it includes interesting case studies and an extensive bibliography.

  13. Virtual Machine Introspection

    Directory of Open Access Journals (Sweden)

    S C Rachana

    2014-06-01

    Full Text Available Cloud computing is an Internet-based computing solution which provides the resources in an effective manner. A very serious issue in cloud computing is security which is a major obstacle for the adoption of cloud. The most important threats of cloud computing are Multitenancy, Availability, Loss of control, Loss of Data, outside attacks, DOS attacks, malicious insiders, etc. Among many security issues in cloud, the Virtual Machine Security is one of the very serious issues. Thus, monitoring of virtual machine is essential. The paper proposes a Virtual Network Introspection [VMI] System to secure the Virtual machines from Distributed Denial of Service [DDOS] and Zombie attacks.

  14. Virtual Machine Introspection

    Directory of Open Access Journals (Sweden)

    S C Rachana

    2015-11-01

    Full Text Available Cloud computing is an Internet-based computing solution which provides the resources in an effective manner. A very serious issue in cloud computing is security which is a major obstacle for the adoption of cloud. The most important threats of cloud computing are Multitenancy, Availability, Loss of control, Loss of Data, outside attacks, DOS attacks, malicious insiders, etc. Among many security issues in cloud, the Virtual Machine Security is one of the very serious issues. Thus, monitoring of virtual machine is essential. The paper proposes a Virtual Network Introspection [VMI] System to secure the Virtual machines from Distributed Denial of Service [DDOS] and Zombie attacks.

  15. Machine Learning for Hackers

    CERN Document Server

    Conway, Drew

    2012-01-01

    If you're an experienced programmer interested in crunching data, this book will get you started with machine learning-a toolkit of algorithms that enables computers to train themselves to automate useful tasks. Authors Drew Conway and John Myles White help you understand machine learning and statistics tools through a series of hands-on case studies, instead of a traditional math-heavy presentation. Each chapter focuses on a specific problem in machine learning, such as classification, prediction, optimization, and recommendation. Using the R programming language, you'll learn how to analyz

  16. Probiotics: Safety and Side Effects

    Science.gov (United States)

    ... of this page please turn JavaScript on. Feature: Probiotics Safety and Side Effects Past Issues / Winter 2016 ... Says About the Safety and Side Effects of Probiotics Whether probiotics are likely to be safe for ...

  17. Some relations between quantum Turing machines and Turing machines

    CERN Document Server

    Sicard, A; Sicard, Andrés; Vélez, Mario

    1999-01-01

    For quantum Turing machines we present three elements: Its components, its time evolution operator and its local transition function. The components are related with deterministic Turing machines, the time evolution operator is related with reversible Turing machines and the local transition function is related with probabilistic and reversible Turing machines.

  18. HIV Medicines and Side Effects

    Science.gov (United States)

    Side Effects of HIV Medicines HIV Medicines and Side Effects (Last updated 1/17/2017; last reviewed 1/17/2017) Key Points HIV medicines help people with ... will depend on a person’s individual needs. Can HIV medicines cause side effects? HIV medicines help people ...

  19. Machining of hard-to-machine materials

    OpenAIRE

    2016-01-01

    Bakalářská práce se zabývá studiem obrábění těžkoobrobitelných materiálů. V první části jsou rozděleny těžkoobrobitelné materiály a následuje jejich analýza. V další části se práce zaměřuje na problematiku obrobitelnosti jednotlivých slitin. Závěrečná část práce je věnovaná experimentu, jeho statistickému zpracování a nakonec následnému vyhodnocení. This bachelor thesis studies the machining of hard-to-machine materials. The first part of the thesis considers hard-to-machine materials and ...

  20. Machine (bulk) harvest

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This is a summary of machine harvesting activities on Neal Smith National Wildlife Refuge between 1991 and 2008. Information is provided for each year about...

  1. Machine Vision Handbook

    CERN Document Server

    2012-01-01

    The automation of visual inspection is becoming more and more important in modern industry as a consistent, reliable means of judging the quality of raw materials and manufactured goods . The Machine Vision Handbook  equips the reader with the practical details required to engineer integrated mechanical-optical-electronic-software systems. Machine vision is first set in the context of basic information on light, natural vision, colour sensing and optics. The physical apparatus required for mechanized image capture – lenses, cameras, scanners and light sources – are discussed followed by detailed treatment of various image-processing methods including an introduction to the QT image processing system. QT is unique to this book, and provides an example of a practical machine vision system along with extensive libraries of useful commands, functions and images which can be implemented by the reader. The main text of the book is completed by studies of a wide variety of applications of machine vision in insp...

  2. Electrical-assisted double side incremental forming and processes thereof

    Science.gov (United States)

    Roth, John; Cao, Jian

    2014-06-03

    A process for forming a sheet metal component using an electric current passing through the component is provided. The process can include providing a double side incremental forming machine, the machine operable to perform a plurality of double side incremental deformations on the sheet metal component and also apply an electric direct current to the sheet metal component during at least part of the forming. The direct current can be applied before or after the forming has started and/or be terminated before or after the forming has stopped. The direct current can be applied to any portion of the sheet metal. The electrical assistance can reduce the magnitude of force required to produce a given amount of deformation, increase the amount of deformation exhibited before failure and/or reduce any springback typically exhibited by the sheet metal component.

  3. Comparisons between designs for single-sided linear electric motors: Homopolar synchronous and induction

    Science.gov (United States)

    Nondahl, T. A.; Richter, E.

    1980-09-01

    A design study of two types of single sided (with a passive rail) linear electric machine designs, namely homopolar linear synchronous machines (LSM's) and linear induction machines (LIM's), is described. It is assumed the machines provide tractive effort for several types of light rail vehicles and locomotives. These vehicles are wheel supported and require tractive powers ranging from 200 kW to 3735 kW and top speeds ranging from 112 km/hr to 400 km/hr. All designs are made according to specified magnetic and thermal criteria. The LSM advantages are a higher power factor, much greater restoring forces for track misalignments, and less track heating. The LIM advantages are no need to synchronize the excitation frequency precisely to vehicle speed, simpler machine construction, and a more easily anchored track structure. The relative weights of the two machine types vary with excitation frequency and speed; low frequencies and low speeds favor the LSM.

  4. Tests of Machine Intelligence

    CERN Document Server

    Legg, Shane

    2007-01-01

    Although the definition and measurement of intelligence is clearly of fundamental importance to the field of artificial intelligence, no general survey of definitions and tests of machine intelligence exists. Indeed few researchers are even aware of alternatives to the Turing test and its many derivatives. In this paper we fill this gap by providing a short survey of the many tests of machine intelligence that have been proposed.

  5. Metalworking and machining fluids

    Science.gov (United States)

    Erdemir, Ali; Sykora, Frank; Dorbeck, Mark

    2010-10-12

    Improved boron-based metal working and machining fluids. Boric acid and boron-based additives that, when mixed with certain carrier fluids, such as water, cellulose and/or cellulose derivatives, polyhydric alcohol, polyalkylene glycol, polyvinyl alcohol, starch, dextrin, in solid and/or solvated forms result in improved metalworking and machining of metallic work pieces. Fluids manufactured with boric acid or boron-based additives effectively reduce friction, prevent galling and severe wear problems on cutting and forming tools.

  6. mlpy: Machine Learning Python

    CERN Document Server

    Albanese, Davide; Merler, Stefano; Riccadonna, Samantha; Jurman, Giuseppe; Furlanello, Cesare

    2012-01-01

    mlpy is a Python Open Source Machine Learning library built on top of NumPy/SciPy and the GNU Scientific Libraries. mlpy provides a wide range of state-of-the-art machine learning methods for supervised and unsupervised problems and it is aimed at finding a reasonable compromise among modularity, maintainability, reproducibility, usability and efficiency. mlpy is multiplatform, it works with Python 2 and 3 and it is distributed under GPL3 at the website http://mlpy.fbk.eu.

  7. Human-machine interactions

    Science.gov (United States)

    Forsythe, J. Chris; Xavier, Patrick G.; Abbott, Robert G.; Brannon, Nathan G.; Bernard, Michael L.; Speed, Ann E.

    2009-04-28

    Digital technology utilizing a cognitive model based on human naturalistic decision-making processes, including pattern recognition and episodic memory, can reduce the dependency of human-machine interactions on the abilities of a human user and can enable a machine to more closely emulate human-like responses. Such a cognitive model can enable digital technology to use cognitive capacities fundamental to human-like communication and cooperation to interact with humans.

  8. Machine Learning with Distances

    Science.gov (United States)

    2015-02-16

    and demonstrated their usefulness in experiments. 1 Introduction The goal of machine learning is to find useful knowledge behind data. Many machine...212, 172]. However, direct divergence approximators still suffer from the curse of dimensionality. A possible cure for this problem is to combine them...obtain the global optimal solution or even a good local solution without any prior knowledge . For this reason, we decided to introduce the unit-norm

  9. mlpy: Machine Learning Python

    OpenAIRE

    Albanese, Davide; Visintainer, Roberto; Merler, Stefano; Riccadonna, Samantha; Jurman, Giuseppe; Furlanello, Cesare

    2012-01-01

    mlpy is a Python Open Source Machine Learning library built on top of NumPy/SciPy and the GNU Scientific Libraries. mlpy provides a wide range of state-of-the-art machine learning methods for supervised and unsupervised problems and it is aimed at finding a reasonable compromise among modularity, maintainability, reproducibility, usability and efficiency. mlpy is multiplatform, it works with Python 2 and 3 and it is distributed under GPL3 at the website http://mlpy.fbk.eu.

  10. AWA RMAT Service Requests

    Data.gov (United States)

    Department of Transportation — Lotus Notes application used by local support to request AWA Tier 3 support (RMATS). Consolidates and automates several routine IT support tasks and facilitates more...

  11. TRANSPORT/HANDLING REQUESTS

    CERN Multimedia

    Groupe ST/HM

    2002-01-01

    A new EDH document entitled 'Transport/Handling Request' will be in operation as of Monday, 11th February 2002, when the corresponding icon will be accessible from the EDH desktop, together with the application instructions. This EDH form will replace the paper-format transport/handling request form for all activities involving the transport of equipment and materials. However, the paper form will still be used for all vehicle-hire requests. The introduction of the EDH transport/handling request form is accompanied by the establishment of the following time limits for the various services concerned: 24 hours for the removal of office items, 48 hours for the transport of heavy items (of up to 6 metric tons and of standard road width), 5 working days for a crane operation, extra-heavy transport operation or complete removal, 5 working days for all transport operations relating to LHC installation. ST/HM Group, Logistics Section Tel: 72672 - 72202

  12. EVALUATION OF MACHINE TOOL QUALITY

    Directory of Open Access Journals (Sweden)

    Ivan Kuric

    2011-12-01

    Full Text Available Paper deals with aspects of quality and accuracy of machine tools. As the accuracy of machine tools has key factor for product quality, it is important to know the methods for evaluation of quality and accuracy of machine tools. Several aspects of diagnostics of machine tools are described, such as aspects of reliability.

  13. An HTS machine laboratory prototype

    DEFF Research Database (Denmark)

    Mijatovic, Nenad; Jensen, Bogi Bech; Træholt, Chresten

    2012-01-01

    This paper describes Superwind HTS machine laboratory setup which is a small scale HTS machine designed and build as a part of the efforts to identify and tackle some of the challenges the HTS machine design may face. One of the challenges of HTS machines is a Torque Transfer Element (TTE) which...

  14. Change-Exchange Currency based Vending Machine using VHDL

    Directory of Open Access Journals (Sweden)

    Nikita Khandelwal

    2013-01-01

    Full Text Available A vending machine is a coin-operated, automatic device which dispenses items such as snacks, beverages, lottery tickets, consumer products and even gold and gems to customers automatically, after the customer inserts currency or credit into the machine. These are more accessible and practical than the convention purchasing method. It is for the reason that vending machines provide us for our necessities almost instantly and with high quality, that people consider it as a very much reliable choice. In this paper a new approach is proposed to design a Vending Machine with automatic currency change or exchange multi select feature using which user can get a change of its currency or can exchange its currency to other available currency options. The machine also supports a cancel feature which means that the user can withdraw the request and the money will be returned back to him. This machine can be used at various places like Hotels, Restaurants, Stations and shopping centers. This reduces the time and cost. The proposed model is implemented using FPGA, the simulation results and circuit parameters are also presented.

  15. Machining of fiber reinforced composites

    Science.gov (United States)

    Komanduri, Ranga; Zhang, Bi; Vissa, Chandra M.

    Factors involved in machining of fiber-reinforced composites are reviewed. Consideration is given to properties of composites reinforced with boron filaments, glass fibers, aramid fibers, carbon fibers, and silicon carbide fibers and to polymer (organic) matrix composites, metal matrix composites, and ceramic matrix composites, as well as to the processes used in conventional machining of boron-titanium composites and of composites reinforced by each of these fibers. Particular attention is given to the methods of nonconventional machining, such as laser machining, water jet cutting, electrical discharge machining, and ultrasonic assisted machining. Also discussed are safety precautions which must be taken during machining of fiber-containing composites.

  16. Machining of Metal Matrix Composites

    CERN Document Server

    2012-01-01

    Machining of Metal Matrix Composites provides the fundamentals and recent advances in the study of machining of metal matrix composites (MMCs). Each chapter is written by an international expert in this important field of research. Machining of Metal Matrix Composites gives the reader information on machining of MMCs with a special emphasis on aluminium matrix composites. Chapter 1 provides the mechanics and modelling of chip formation for traditional machining processes. Chapter 2 is dedicated to surface integrity when machining MMCs. Chapter 3 describes the machinability aspects of MMCs. Chapter 4 contains information on traditional machining processes and Chapter 5 is dedicated to the grinding of MMCs. Chapter 6 describes the dry cutting of MMCs with SiC particulate reinforcement. Finally, Chapter 7 is dedicated to computational methods and optimization in the machining of MMCs. Machining of Metal Matrix Composites can serve as a useful reference for academics, manufacturing and materials researchers, manu...

  17. Non-conventional electrical machines

    CERN Document Server

    Rezzoug, Abderrezak

    2013-01-01

    The developments of electrical machines are due to the convergence of material progress, improved calculation tools, and new feeding sources. Among the many recent machines, the authors have chosen, in this first book, to relate the progress in slow speed machines, high speed machines, and superconducting machines. The first part of the book is dedicated to materials and an overview of magnetism, mechanic, and heat transfer.

  18. Machinability evaluation of machinable ceramics with fuzzy theory

    Institute of Scientific and Technical Information of China (English)

    YU Ai-bing; ZHONG Li-jun; TAN Ye-fa

    2005-01-01

    The property parameters and machining output parameters were selected for machinability evaluation of machinable ceramics. Based on fuzzy evaluation theory, two-stage fuzzy evaluation approach was applied to consider these parameters. Two-stage fuzzy comprehensive evaluation model was proposed to evaluate machinability of machinable ceramic materials. Ce-ZrO2/CePO4 composites were fabricated and machined for evaluation of machinable ceramics. Material removal rates and specific normal grinding forces were measured. The parameters concerned with machinability were selected as alternative set. Five grades were chosen for the machinability evaluation of machnable ceramics. Machinability grades of machinable ceramics were determined through fuzzy operation. Ductile marks are observed on Ce-ZrO2/CePO4 machined surface. Five prepared Ce-ZrO2/CePO4 composites are classified as three machinability grades according to the fuzzy comprehensive evaluation results. The machinability grades of Ce-ZrO2/CePO4 composites are concerned with CePO4 content.

  19. MACHINE MOTION EQUATIONS

    Directory of Open Access Journals (Sweden)

    Florian Ion Tiberiu Petrescu

    2015-09-01

    Full Text Available This paper presents the dynamic, original, machine motion equations. The equation of motion of the machine that generates angular speed of the shaft (which varies with position and rotation speed is deduced by conservation kinetic energy of the machine. An additional variation of angular speed is added by multiplying by the coefficient dynamic D (generated by the forces out of mechanism and or by the forces generated by the elasticity of the system. Kinetic energy conservation shows angular speed variation (from the shaft with inertial masses, while the dynamic coefficient introduces the variation of w with forces acting in the mechanism. Deriving the first equation of motion of the machine one can obtain the second equation of motion dynamic. From the second equation of motion of the machine it determines the angular acceleration of the shaft. It shows the distribution of the forces on the mechanism to the internal combustion heat engines. Dynamic, the velocities can be distributed in the same way as forces. Practically, in the dynamic regimes, the velocities have the same timing as the forces. Calculations should be made for an engine with a single cylinder. Originally exemplification is done for a classic distribution mechanism, and then even the module B distribution mechanism of an Otto engine type.

  20. Flexible Envelope Request Notation (FERN)

    Science.gov (United States)

    Zoch, David R.; Lavallee, David; Weinstein, Stuart

    1991-01-01

    The following topics are presented in view graph form and include the following: scheduling application; the motivation for the Flexible Envelope Request Notation (FERN); characteristics of FERN; types of information needed in requests; where information is stored in requests; FERN structures; generic requests; resource availability for pooled resources; expressive notation; temporal constraints; time formats; changes to FERN; sample FERN requests; the temporal relationship between two steps; maximum activity length to limit step delays; alternative requests; the temporal relationship between two activities; and idle resource usage between steps.

  1. Three sided complex adaptative systems

    CERN Document Server

    D'Hulst, R

    1999-01-01

    We introduce two three sided adaptative systems as toy models to mimic the exchange of commodities between buyers and sellers. These models are simple extensions of the minority game, exhibiting similar behaviour as well as some new features. The main difference between our two models is that in the first the three sides are equivalent while in the second, one choice appears as a compromise between the two other sides. Both models are investigated numerically and compared with the original minority game.

  2. Fingerprinting Communication and Computation on HPC Machines

    Energy Technology Data Exchange (ETDEWEB)

    Peisert, Sean

    2010-06-02

    How do we identify what is actually running on high-performance computing systems? Names of binaries, dynamic libraries loaded, or other elements in a submission to a batch queue can give clues, but binary names can be changed, and libraries provide limited insight and resolution on the code being run. In this paper, we present a method for"fingerprinting" code running on HPC machines using elements of communication and computation. We then discuss how that fingerprint can be used to determine if the code is consistent with certain other types of codes, what a user usually runs, or what the user requested an allocation to do. In some cases, our techniques enable us to fingerprint HPC codes using runtime MPI data with a high degree of accuracy.

  3. Dynamics of cyclic machines

    CERN Document Server

    Vulfson, Iosif

    2015-01-01

    This book focuses on modern methods of oscillation analysis in machines, including cyclic action mechanisms (linkages, cams, steppers, etc.). It presents schematization techniques and mathematical descriptions of oscillating systems, taking into account the variability of the parameters and nonlinearities, engineering evaluations of dynamic errors, and oscillation suppression methods. The majority of the book is devoted to the development of new methods of dynamic analysis and synthesis for cyclic machines that form regular oscillatory systems with multiple duplicate modules.  There are also sections examining aspects of general engineering interest (nonlinear dissipative forces, systems with non-stationary constraints, impacts and pseudo-impacts in clearances, etc.)  The examples in the book are based on the widely used results of theoretical and experimental studies as well as engineering calculations carried out in relation to machines used in the textile, light, polygraphic and other industries. Particu...

  4. Chatter and machine tools

    CERN Document Server

    Stone, Brian

    2014-01-01

    Focussing on occurrences of unstable vibrations, or Chatter, in machine tools, this book gives important insights into how to eliminate chatter with associated improvements in product quality, surface finish and tool wear. Covering a wide range of machining processes, including turning, drilling, milling and grinding, the author uses his research expertise and practical knowledge of vibration problems to provide solutions supported by experimental evidence of their effectiveness. In addition, this book contains links to supplementary animation programs that help readers to visualise the ideas detailed in the text. Advancing knowledge in chatter avoidance and suggesting areas for new innovations, Chatter and Machine Tools serves as a handbook for those desiring to achieve significant reductions in noise, longer tool and grinding wheel life and improved product finish.

  5. Machines and Metaphors

    Directory of Open Access Journals (Sweden)

    Ángel Martínez García-Posada

    2016-10-01

    Full Text Available The edition La ley del reloj. Arquitectura, máquinas y cultura moderna (Cátedra, Madrid, 2016 registers the useful paradox of the analogy between architecture and technique. Its author, the architect Eduardo Prieto, also a philosopher, professor and writer, acknowledges the obvious distance from machines to buildings, so great that it can only be solved using strange comparisons, since architecture does not move nor are the machines habitable, however throughout the book, from the origin of the metaphor of the machine, with clarity in his essay and enlightening erudition, he points out with certainty some concomitances of high interest, drawing throughout history a beautiful cartography of the fruitful encounter between organics and mechanics.

  6. Machine Learning Markets

    CERN Document Server

    Storkey, Amos

    2011-01-01

    Prediction markets show considerable promise for developing flexible mechanisms for machine learning. Here, machine learning markets for multivariate systems are defined, and a utility-based framework is established for their analysis. This differs from the usual approach of defining static betting functions. It is shown that such markets can implement model combination methods used in machine learning, such as product of expert and mixture of expert approaches as equilibrium pricing models, by varying agent utility functions. They can also implement models composed of local potentials, and message passing methods. Prediction markets also allow for more flexible combinations, by combining multiple different utility functions. Conversely, the market mechanisms implement inference in the relevant probabilistic models. This means that market mechanism can be utilized for implementing parallelized model building and inference for probabilistic modelling.

  7. Machine Learning for Security

    CERN Document Server

    CERN. Geneva

    2015-01-01

    Applied statistics, aka ‘Machine Learning’, offers a wealth of techniques for answering security questions. It’s a much hyped topic in the big data world, with many companies now providing machine learning as a service. This talk will demystify these techniques, explain the math, and demonstrate their application to security problems. The presentation will include how-to’s on classifying malware, looking into encrypted tunnels, and finding botnets in DNS data. About the speaker Josiah is a security researcher with HP TippingPoint DVLabs Research Group. He has over 15 years of professional software development experience. Josiah used to do AI, with work focused on graph theory, search, and deductive inference on large knowledge bases. As rules only get you so far, he moved from AI to using machine learning techniques identifying failure modes in email traffic. There followed digressions into clustered data storage and later integrated control systems. Current ...

  8. Advanced Analysis of Nontraditional Machining

    CERN Document Server

    Tsai, Hung-Yin

    2013-01-01

    Nontraditional machining utilizes thermal, chemical, electrical, mechanical and optical sources of energy to form and cut materials. Advanced Analysis of Nontraditional Machining explains in-depth how each of these advanced machining processes work, their machining system components, and process variables and industrial applications, thereby offering advanced knowledge and scientific insight. This book also documents the latest and frequently cited research results of a few key nonconventional machining processes for the most concerned topics in industrial applications, such as laser machining, electrical discharge machining, electropolishing of die and mold, and wafer processing for integrated circuit manufacturing. This book also: Fills the gap of the advanced knowledge of nonconventional machining between industry and research Documents latest and frequently cited research of key nonconventional machining processes for the most sought after topics in industrial applications Demonstrates advanced multidisci...

  9. Machining strategy choice: performance VIEWER

    CERN Document Server

    Tapie, Laurent; Anselmetti, Bernard

    2009-01-01

    Nowadays high speed machining (HSM) machine tool combines productivity and part quality. So mould and die maker invested in HSM. Die and mould features are more and more complex shaped. Thus, it is difficult to choose the best machining strategy according to part shape. Geometrical analysis of machining features is not sufficient to make an optimal choice. Some research show that security, technical, functional and economical constrains must be taken into account to elaborate a machining strategy. During complex shape machining, production system limits induce feed rate decreases, thus loss of productivity, in some part areas. In this paper we propose to analyse these areas by estimating tool path quality. First we perform experiments on HSM machine tool to determine trajectory impact on machine tool behaviour. Then, we extract critical criteria and establish models of performance loss. Our work is focused on machine tool kinematical performance and numerical controller unit calculation capacity. We implement...

  10. The Perfect Science Machine

    Science.gov (United States)

    2008-05-01

    ESO celebrates 10 years since First Light of the VLT Today marks the 10th anniversary since First Light with ESO's Very Large Telescope (VLT), the most advanced optical telescope in the world. Since then, the VLT has evolved into a unique suite of four 8.2-m Unit Telescopes (UTs) equipped with no fewer than 13 state-of-the-art instruments, and four 1.8-m moveable Auxiliary Telescopes (ATs). The telescopes can work individually, and they can also be linked together in groups of two or three to form a giant 'interferometer' (VLTI), allowing astronomers to see details corresponding to those from a much larger telescope. Green Flash at Paranal ESO PR Photo 16a/08 The VLT 10th anniversary poster "The Very Large Telescope array is a flagship facility for astronomy, a perfect science machine of which Europe can be very proud," says Tim de Zeeuw, ESO's Director General. "We have built the most advanced ground-based optical observatory in the world, thanks to the combination of a long-term adequately-funded instrument and technology development plan with an approach where most of the instruments were built in collaboration with institutions in the member states, with in-kind contributions in labour compensated by guaranteed observing time." Sitting atop the 2600m high Paranal Mountain in the Chilean Atacama Desert, the VLT's design, suite of instruments, and operating principles set the standard for ground-based astronomy. It provides the European scientific community with a telescope array with collecting power significantly greater than any other facilities available at present, offering imaging and spectroscopy capabilities at visible and infrared wavelengths. Blue Flash at Paranal ESO PR Photo 16b/08 A Universe of Discoveries The first scientifically useful images, marking the official 'First Light' of the VLT, were obtained on the night of 25 to 26 May 1998, with a test camera attached to "Antu", Unit Telescope number 1. They were officially presented to the press on

  11. Variable-Speed, Robust Synchronous Reluctance Machine Drive Systems

    DEFF Research Database (Denmark)

    Wang, Dong

    algorithm, the proposed machine inductance in-dependent position estimation algorithm shows better dynamic response against the step load changes but requires more accurate signal sampling in steady state. Therefore, the flux linkage based position estimation algorithm with adaptive PI controllers......The synchronous reluctance machine drive is getting more and more interests from the industrial side, since it can provide higher system energy efficiency than traditional inverter-fed induction machine drive systems with similar production cost. It is considered as a good candidate for super...... inductance independency. High frequency signal injection based on duty cycle shifting is introduced, which can achieve signal injection without sacrificing the maximum allowable fundamental voltage for torque production, so that the machine induct-ance independent position estimation algorithm can...

  12. Electrical machines diagnosis

    CERN Document Server

    Trigeassou, Jean-Claude

    2013-01-01

    Monitoring and diagnosis of electrical machine faults is a scientific and economic issue which is motivated by objectives for reliability and serviceability in electrical drives.This book provides a survey of the techniques used to detect the faults occurring in electrical drives: electrical, thermal and mechanical faults of the electrical machine, faults of the static converter and faults of the energy storage unit.Diagnosis of faults occurring in electrical drives is an essential part of a global monitoring system used to improve reliability and serviceability. This diagnosis is perf

  13. Refrigerating machine oil

    Energy Technology Data Exchange (ETDEWEB)

    Nozawa, K.

    1981-03-17

    Refrigerating machine oil to be filled in a sealed motorcompressor unit constituting a refrigerating cycle system including an electric refrigerator, an electric cold-storage box, a small-scaled electric refrigerating show-case, a small-scaled electric cold-storage show-case and the like, is arranged to have a specifically enhanced property, in which smaller initial driving power consumption of the sealed motor-compressor and easier supply of the predetermined amount of the refrigerating machine oil to the refrigerating system are both guaranteed even in a rather low environmental temperature condition.

  14. Machine shop basics

    CERN Document Server

    Miller, Rex

    2004-01-01

    Use the right tool the right wayHere, fully updated to include new machines and electronic/digital controls, is the ultimate guide to basic machine shop equipment and how to use it. Whether you're a professional machinist, an apprentice, a trade student, or a handy homeowner, this fully illustrated volume helps you define tools and use them properly and safely. It's packed with review questions for students, and loaded with answers you need on the job.Mark Richard Miller is a Professor and Chairman of the Industrial Technology Department at Texas A&M University in Kingsville, T

  15. Electrical machines & their applications

    CERN Document Server

    Hindmarsh, J

    1984-01-01

    A self-contained, comprehensive and unified treatment of electrical machines, including consideration of their control characteristics in both conventional and semiconductor switched circuits. This new edition has been expanded and updated to include material which reflects current thinking and practice. All references have been updated to conform to the latest national (BS) and international (IEC) recommendations and a new appendix has been added which deals more fully with the theory of permanent-magnets, recognising the growing importance of permanent-magnet machines. The text is so arra

  16. Clojure for machine learning

    CERN Document Server

    Wali, Akhil

    2014-01-01

    A book that brings out the strengths of Clojure programming that have to facilitate machine learning. Each topic is described in substantial detail, and examples and libraries in Clojure are also demonstrated.This book is intended for Clojure developers who want to explore the area of machine learning. Basic understanding of the Clojure programming language is required, but thorough acquaintance with the standard Clojure library or any libraries are not required. Familiarity with theoretical concepts and notation of mathematics and statistics would be an added advantage.

  17. Perpetual Motion Machine

    OpenAIRE

    D. Tsaousis

    2008-01-01

    Ever since the first century A.D. there have been relative descriptions of known devices as well as manufactures for the creation of perpetual motion machines. Although physics has led, with two thermodynamic laws, to the opinion that a perpetual motion machine is impossible to be manufactured, inventors of every age and educational level appear to claim that they have invented something «entirely new» or they have improved somebody else’s invention, which «will function henceforth perpetuall...

  18. Man - Machine Communication

    CERN Document Server

    Petersen, Peter; Nielsen, Henning

    1984-01-01

    This report describes a Man-to-Machine Communication module which together with a STAC can take care of all operator inputs from the touch-screen, tracker balls and mechanical buttons. The MMC module can also contain a G64 card which could be a GPIB driver but many other G64 cards could be used. The soft-ware services the input devices and makes the results accessible from the CAMAC bus. NODAL functions for the Man Machine Communication is implemented in the STAC and in the ICC.

  19. Machine Fault Signature Analysis

    Directory of Open Access Journals (Sweden)

    Pratesh Jayaswal

    2008-01-01

    Full Text Available The objective of this paper is to present recent developments in the field of machine fault signature analysis with particular regard to vibration analysis. The different types of faults that can be identified from the vibration signature analysis are, for example, gear fault, rolling contact bearing fault, journal bearing fault, flexible coupling faults, and electrical machine fault. It is not the intention of the authors to attempt to provide a detailed coverage of all the faults while detailed consideration is given to the subject of the rolling element bearing fault signature analysis.

  20. Design of rotating electrical machines

    CERN Document Server

    Pyrhonen , Juha; Hrabovcova , Valeria

    2013-01-01

    In one complete volume, this essential reference presents an in-depth overview of the theoretical principles and techniques of electrical machine design. This timely new edition offers up-to-date theory and guidelines for the design of electrical machines, taking into account recent advances in permanent magnet machines as well as synchronous reluctance machines. New coverage includes: Brand new material on the ecological impact of the motors, covering the eco-design principles of rotating electrical machinesAn expanded section on the design of permanent magnet synchronous machines, now repo

  1. Challenges in Request Management

    DEFF Research Database (Denmark)

    Sommer, Anita Friis

    2014-01-01

    Request management (RQM) is a new term used for managing customer requests for new products. It is the counterpart to typical product development processes, which has no direct customer involvement. It is essential to manage customer requests in a structured and efficient way to obtain...... profitability. This research study seeks to investigate the challenges of RQM in practice. Existing demand chain management literature is used as a basis for developing a RQM framework. RQM is investigated through an explorative research design in a dyadic B2B case study including a global industrial company...... and its customers. The study provides an insight into a new area of supply chain management, including the process activity flow and challenges involved across the process. Furthermore, the method is dyadic including the customer in the case study, which is rare in related research....

  2. Machine speech and speaking about machines

    Energy Technology Data Exchange (ETDEWEB)

    Nye, A. [Univ. of Wisconsin, Whitewater, WI (United States)

    1996-12-31

    Current philosophy of language prides itself on scientific status. It boasts of being no longer contaminated with queer mental entities or idealist essences. It theorizes language as programmable variants of formal semantic systems, reimaginable either as the properly epiphenomenal machine functions of computer science or the properly material neural networks of physiology. Whether or not such models properly capture the physical workings of a living human brain is a question that scientists will have to answer. I, as a philosopher, come at the problem from another direction. Does contemporary philosophical semantics, in its dominant truth-theoretic and related versions, capture actual living human thought as it is experienced, or does it instead reflect, regardless of (perhaps dubious) scientific credentials, pathology of thought, a pathology with a disturbing social history.

  3. The Dark Side of Creativity

    Science.gov (United States)

    Cropley, David H., Ed.; Cropley, Arthur J., Ed.; Kaufman, James C., Ed.; Runco, Mark A., Ed.

    2010-01-01

    With few exceptions, scholarship on creativity has focused on its positive aspects while largely ignoring its dark side. This includes not only creativity deliberately aimed at hurting others, such as crime or terrorism, or at gaining unfair advantages, but also the accidental negative side effects of well-intentioned acts. This book brings…

  4. Managing Chemotherapy Side Effects: Diarrhea

    Science.gov (United States)

    ... such as Pedialyte ® ••Tea (without caffeine) ••Water ••Applesauce ••Bananas ••Crackers ••Cream of wheat or rice cereal ••Eggs •• ... has a series of 18 Chemotherapy Side Effects Sheets at: www.cancer.gov/chemo-side-effects

  5. Hybrid machining processes perspectives on machining and finishing

    CERN Document Server

    Gupta, Kapil; Laubscher, R F

    2016-01-01

    This book describes various hybrid machining and finishing processes. It gives a critical review of the past work based on them as well as the current trends and research directions. For each hybrid machining process presented, the authors list the method of material removal, machining system, process variables and applications. This book provides a deep understanding of the need, application and mechanism of hybrid machining processes.

  6. Cybernetic anthropomorphic machine systems

    Science.gov (United States)

    Gray, W. E.

    1974-01-01

    Functional descriptions are provided for a number of cybernetic man machine systems that augment the capacity of normal human beings in the areas of strength, reach or physical size, and environmental interaction, and that are also applicable to aiding the neurologically handicapped. Teleoperators, computer control, exoskeletal devices, quadruped vehicles, space maintenance systems, and communications equipment are considered.

  7. ARM : abstract rewriting machine

    NARCIS (Netherlands)

    J.F.T. Kamperman; H.R. Walters (Pum)

    1993-01-01

    textabstractTerm rewriting is frequently used as implementation technique for algebraic specifications. In this paper we present the abstract term rewriting machine (ARM), which has an extremely compact instruction set and imposes no restrictions on the implemented TRSs. Apart from standard

  8. A "Living" Machine

    Institute of Scientific and Technical Information of China (English)

    N.R.Bogatyrev

    2004-01-01

    Biomimetics (or bionics) is the engineering discipline that constructs artificial systems using biological principles. The ideal final result in biomimetics is to create a living machine. But what are the desirable and non-desirable properties of biomimetic product? Where can natural prototypes be found? How can technical solutions be transferred from nature to technology? Can we use living nature like LEGO bricks for construction our machines? How can biology help us? What is a living machine? In biomimetic practice only some "part" (organ, part of organ, tissue) of the observed whole organism is utilized. A possible template for future super-organism extension for biomimetic methods might be drawn from experiments in holistic ecological agriculture (ecological design, permaculture, ecological engineering, etc. ). The necessary translation of these rules to practical action can be achieved with the Russian Theory of Inventive Problem Solving (TRIZ), specifically adjusted to biology. Thus, permaculture, reinforced by a TRIZ conceptual framework, might provide the basis for Super-Organismic Bionics, which is hypothesized as necessary for effective ecological engineering. This hypothesis is supported by a case study-the design of a sustainable artificial nature reserve for wild pollinators as a living machine.

  9. Of machines and men ...

    CERN Multimedia

    CERN; Daniel Boileau

    1990-01-01

    Engineering and construction at LEP. Committed work and physicists motivation to work on this type of machine. With Guido Altarelli Theory Division Physicist, Ugo Amaldi Delphi Experiment Spokesman, Oscar Barbalat Head of Industry and Technology Liaison Office, Jonathan Ellis Head of Theory Division.

  10. Technology Time Machine 2012

    DEFF Research Database (Denmark)

    Lehner, Wolfgang; Fettweis, Gerhard; Fitzek, Frank

    2013-01-01

    The IEEE Technology Time Machine (TTM) is a unique event for industry leaders, academics, and decision making government officials who direct R&D activities, plan research programs or manage portfolios of research activities. This report covers the main topics of the 2nd Symposium of future...

  11. Training Restricted Boltzmann Machines

    DEFF Research Database (Denmark)

    Fischer, Asja

    Restricted Boltzmann machines (RBMs) are probabilistic graphical models that can also be interpreted as stochastic neural networks. Training RBMs is known to be challenging. Computing the likelihood of the model parameters or its gradient is in general computationally intensive. Thus, training...

  12. Laser machining of explosives

    Science.gov (United States)

    Perry, Michael D.; Stuart, Brent C.; Banks, Paul S.; Myers, Booth R.; Sefcik, Joseph A.

    2000-01-01

    The invention consists of a method for machining (cutting, drilling, sculpting) of explosives (e.g., TNT, TATB, PETN, RDX, etc.). By using pulses of a duration in the range of 5 femtoseconds to 50 picoseconds, extremely precise and rapid machining can be achieved with essentially no heat or shock affected zone. In this method, material is removed by a nonthermal mechanism. A combination of multiphoton and collisional ionization creates a critical density plasma in a time scale much shorter than electron kinetic energy is transferred to the lattice. The resulting plasma is far from thermal equilibrium. The material is in essence converted from its initial solid-state directly into a fully ionized plasma on a time scale too short for thermal equilibrium to be established with the lattice. As a result, there is negligible heat conduction beyond the region removed resulting in negligible thermal stress or shock to the material beyond a few microns from the laser machined surface. Hydrodynamic expansion of the plasma eliminates the need for any ancillary techniques to remove material and produces extremely high quality machined surfaces. There is no detonation or deflagration of the explosive in the process and the material which is removed is rendered inert.

  13. Electrical Discharge Machining.

    Science.gov (United States)

    Montgomery, C. M.

    The manual is for use by students learning electrical discharge machining (EDM). It consists of eight units divided into several lessons, each designed to meet one of the stated objectives for the unit. The units deal with: introduction to and advantages of EDM, the EDM process, basic components of EDM, reaction between forming tool and workpiece,…

  14. The Answer Machine.

    Science.gov (United States)

    Feldman, Susan

    2000-01-01

    Discusses information retrieval systems and the need to have them adapt to user needs, integrate information in any format, reveal patterns and trends in information, and answer questions. Topics include statistics and probability; natural language processing; intelligent agents; concept mapping; machine-aided indexing; text mining; filtering;…

  15. Massively collaborative machine learning

    NARCIS (Netherlands)

    Rijn, van J.N.

    2016-01-01

    Many scientists are focussed on building models. We nearly process all information we perceive to a model. There are many techniques that enable computers to build models as well. The field of research that develops such techniques is called Machine Learning. Many research is devoted to develop comp

  16. Recent Advances on Permanent Magnet Machines

    Institute of Scientific and Technical Information of China (English)

    诸自强

    2012-01-01

    This paper overviews advances on permanent magnet(PM) brushless machines over last 30 years,with particular reference to new and novel machine topologies.These include current states and trends for surface-mounted and interior PM machines,electrically and mechanically adjusted variable flux PM machines including memory machine,hybrid PM machines which uniquely integrate PM technology into induction machines,switched and synchronous reluctance machines and wound field machines,Halbach PM machines,dual-rotor PM machines,and magnetically geared PM machines,etc.The paper highlights their features and applications to various market sectors.

  17. 75 FR 68361 - Agency Information Collection Activities; Proposed Collection; Comment Request; Restaurant Menu...

    Science.gov (United States)

    2010-11-05

    ... recordkeeper records record Restaurant Chains 516 117 60,372 4 241,488 $16.2 million Grocery and Convenience... disclosure Restaurants 135,705 3 407,115 2 814,230 Grocery and Convenience Store Chains 41,945 1 41,945 2 83... Collection; Comment Request; Restaurant Menu and Vending Machine Labeling: Recordkeeping and Mandatory...

  18. Motherhood and the Machine

    Directory of Open Access Journals (Sweden)

    Miglena Nikolchina

    2014-12-01

    Full Text Available In her conceptualization of the human as defined by the capacity for revolt Kristeva unavoidably touches upon issues of robotization, technology, and the virtual. The concepts of animal and machine, however, although they do appear occasionally and in important ways, are never at the focus of her inquiries and are absent in her “New Forms of Revolt.” Yet these two concepts to a large extent define the field of contemporary philosophical debates of the human giving rise to three major theoretical orientations. On the one hand, there is the trend which tries to come to terms with technological novelties and the merging of human and machine that they imply. This trend unfolds under the rubric of “transhuman” or “posthuman” and of the “enhancement” of man. The second trend predominates in animal studies. Mostly in an ethical perspective but also ontologically, this trend, to which Derrida’s later writing made a significant contribution, questions the idea of the “human exception” and the rigorous distinction between man and animal on which this exception rests. While apparently antagonistic, both trends align the human with the animal and oppose it to technology. The third trend collapses the distinctions on which the previous two rely through the lens of biopolitics: drawing on Heidegger, Kojève, and Foucault, it regards contemporary technological transformations as amounting to the animalization of man.  The human disappears in the animal, in the machine, or in the indistinguishability of the two, confirming what Agamben has described as the inoperativeness of the anthropological machine. The present text turns to Kristeva’s conceptions of motherhood and revolt as introducing a powerful inflection in this tripartite field. Remarkably, it is precisely new sagas of rebellious machines like Battlestar “Galactica” that foreground the relevance of Kristeva’s approach.

  19. Machine learning in image steganalysis

    CERN Document Server

    Schaathun, Hans Georg

    2012-01-01

    "The only book to look at steganalysis from the perspective of machine learning theory, and to apply the common technique of machine learning to the particular field of steganalysis; ideal for people working in both disciplines"--

  20. New Applications of Learning Machines

    DEFF Research Database (Denmark)

    Larsen, Jan

    * Machine learning framework for sound search * Genre classification * Music separation * MIMO channel estimation and symbol detection......* Machine learning framework for sound search * Genre classification * Music separation * MIMO channel estimation and symbol detection...

  1. New Applications of Learning Machines

    DEFF Research Database (Denmark)

    Larsen, Jan

    * Machine learning framework for sound search * Genre classification * Music separation * MIMO channel estimation and symbol detection......* Machine learning framework for sound search * Genre classification * Music separation * MIMO channel estimation and symbol detection...

  2. Hinged Shields for Machine Tools

    Science.gov (United States)

    Lallande, J. B.; Poland, W. W.; Tull, S.

    1985-01-01

    Flaps guard against flying chips, but fold away for tool setup. Clear plastic shield in position to intercept flying chips from machine tool and retracted to give operator access to workpiece. Machine shops readily make such shields for own use.

  3. Request for All - Generalized Request Framework for PhEDEx

    CERN Document Server

    Huang, C-H; Ratnikova, N.; Sanchez-Hernandez, A.; Zhang, X.; Magini, N.

    2014-01-01

    PhEDEx has been serving CMS community since 2004 as the data broker. Every PhEDEx operation is initiated by a request, such as request to move data, request to delete data, and so on. A request has it own life cycle, including creation, approval, notification, and book keeping and the details depend on its type. Currently, only two kinds of requests, transfer and deletion, are fully integrated in PhEDEx. They are tailored specifically to the operations workflows. To be able to serve a new type of request it generally means a fair amount of development work.After several years of operation, we have gathered enough experience to rethink the request handling in PhEDEx. Generalized Request Project is set to abstract such experience and come up with a request system which is not tied into current workflow yet it is general enough to accommodate current and future requests.The challenges are dealing with different stages in a requests life cycle, complexity of approval process and complexity of the ability and auth...

  4. Design of Sugarcane Peeling Machine

    Directory of Open Access Journals (Sweden)

    Ge Xinfeng

    2015-02-01

    Full Text Available In order to solve the problem that appeared in hand peeling sugarcane, the sugarcane peeling machine is designed, the sugarcane peeling machine includes motor, groove wheel, cutting room, slider crank mechanism, reducer (including belt drive, chain drive and so on. The designed sugarcane peeling machine is simulated, the results show that the sugarcane peeling machine can peel sugarcane successfully with convenient, fast and uniform.

  5. Automatically-Programed Machine Tools

    Science.gov (United States)

    Purves, L.; Clerman, N.

    1985-01-01

    Software produces cutter location files for numerically-controlled machine tools. APT, acronym for Automatically Programed Tools, is among most widely used software systems for computerized machine tools. APT developed for explicit purpose of providing effective software system for programing NC machine tools. APT system includes specification of APT programing language and language processor, which executes APT statements and generates NC machine-tool motions specified by APT statements.

  6. Automatically-Programed Machine Tools

    Science.gov (United States)

    Purves, L.; Clerman, N.

    1985-01-01

    Software produces cutter location files for numerically-controlled machine tools. APT, acronym for Automatically Programed Tools, is among most widely used software systems for computerized machine tools. APT developed for explicit purpose of providing effective software system for programing NC machine tools. APT system includes specification of APT programing language and language processor, which executes APT statements and generates NC machine-tool motions specified by APT statements.

  7. Feature Recognition for Virtual Machining

    OpenAIRE

    Xú, Shixin; Anwer, Nabil; Qiao, Lihong

    2014-01-01

    International audience; Virtual machining uses software tools to simulate machining processes in virtual environments ahead of actual production. This paper proposes that feature recognition techniques can be applied in the course of virtual machining, such as identifying some process problems, and presenting corresponding correcting advices. By comparing with the original CAD model, form errors of the machining features can be found. And then corrections are suggested to process designers. T...

  8. Blind loop perforation after side-to-side ileocolonic anastomosis

    Institute of Scientific and Technical Information of China (English)

    Raffaele; Dalla; Valle; Roberto; Zinicola; Maurizio; Iaria

    2014-01-01

    Blind loop syndrome after side-to-side ileocolonic anas-tomosis is a well-recognized entity even though its in-cidence and complication rates are not clearly defined. The inevitable dilation of the ileal cul-de-sac leads to stasis and bacterial overgrowth which eventually leads to mucosal ulceration and even full-thickness perfora-tion. Blind loop syndrome may be an underestimated complication in the setting of digestive surgery. It should always be taken into account in cases of acute abdomen in patients who previously underwent right hemicolectomy. We herein report 3 patients who were diagnosed with perforative blind loop syndrome a few years after standard right hemicolectomy followed by a side-to-side ileocolonic anastomosis.

  9. Blind loop perforation after side-to-side ileocolonic anastomosis.

    Science.gov (United States)

    Valle, Raffaele Dalla; Zinicola, Roberto; Iaria, Maurizio

    2014-08-27

    Blind loop syndrome after side-to-side ileocolonic anastomosis is a well-recognized entity even though its incidence and complication rates are not clearly defined. The inevitable dilation of the ileal cul-de-sac leads to stasis and bacterial overgrowth which eventually leads to mucosal ulceration and even full-thickness perforation. Blind loop syndrome may be an underestimated complication in the setting of digestive surgery. It should always be taken into account in cases of acute abdomen in patients who previously underwent right hemicolectomy. We herein report 3 patients who were diagnosed with perforative blind loop syndrome a few years after standard right hemicolectomy followed by a side-to-side ileocolonic anastomosis.

  10. Two-Sided Tests and One-Sided Confidence Bounds

    OpenAIRE

    1994-01-01

    Based on the duality between tests and confidence sets we introduce a new method to derive one-sided confidence bounds following the rejection of a null hypothesis with two-sided alternatives. This method imputes that the experimenter is only interested in confidence bounds if the null hypothesis is rejected. Furthermore, we suppose that he is only interested in the direction and a lower confidence bound concerning the distance of the true parameter value to the parameter values in the null h...

  11. The Neural Support Vector Machine

    NARCIS (Netherlands)

    Wiering, Marco; van der Ree, Michiel; Embrechts, Mark; Stollenga, Marijn; Meijster, Arnold; Nolte, A; Schomaker, Lambertus

    2013-01-01

    This paper describes a new machine learning algorithm for regression and dimensionality reduction tasks. The Neural Support Vector Machine (NSVM) is a hybrid learning algorithm consisting of neural networks and support vector machines (SVMs). The output of the NSVM is given by SVMs that take a

  12. The Neural Support Vector Machine

    NARCIS (Netherlands)

    Wiering, Marco; van der Ree, Michiel; Embrechts, Mark; Stollenga, Marijn; Meijster, Arnold; Nolte, A; Schomaker, Lambertus

    2013-01-01

    This paper describes a new machine learning algorithm for regression and dimensionality reduction tasks. The Neural Support Vector Machine (NSVM) is a hybrid learning algorithm consisting of neural networks and support vector machines (SVMs). The output of the NSVM is given by SVMs that take a centr

  13. At Your Request

    NARCIS (Netherlands)

    Doorduijn, A.S.; Gameren, van Yvonne; Vasse, Emmelyne; Roos, de N.M.

    2016-01-01

    Background: Malnutrition in hospitals may be combatted by improving the meal service. Aim: To evaluate whether At Your Request®, a meal service concept by Sodexo with a restaurant style menu card and room service, improved patient satisfaction, nutritional status, and food intake compa

  14. At Your Request

    NARCIS (Netherlands)

    Doorduijn, A.S.; Gameren, van Yvonne; Vasse, Emmelyne; Roos, de N.M.

    2016-01-01

    Background: Malnutrition in hospitals may be combatted by improving the meal service. Aim: To evaluate whether At Your Request®, a meal service concept by Sodexo with a restaurant style menu card and room service, improved patient satisfaction, nutritional status, and food intake

  15. The DarkSide project

    Energy Technology Data Exchange (ETDEWEB)

    Agnes, P.; Agostino, L.; Albuquerque, Ivone Freire Da Mota; Alexander, Thomas R.; Alton, A.; Arisaka, K.; Back, Henning O.; Baldin, B.; Biery, K.; Bonfini, G.; Bossa, M.; Bottino, Bianca; Brigatti, A.; Brodsky, J.; Budano, F.; Bussino, Severino; Cadeddu, Matteo; Cadonati, L.; Cadoni, M.; Calaprice, F.; Canci, N.; Candela, A.; Cao, H.; Cariello, M.; Carlini, Macro; Catalanotti, Sergio; Cavalcante, P.; Chepurnov, A.; Cocco, A. G.; Covone, G.; Crippa, L.; D' Angelo, D.; D' Incecco, M.; Davini, S.; De Cecco, Sandro; De Deo, M.; De Vincenzi, Mario; Derbin, A.; Devoto, A.; Di Eusanio, F.; Di Pietro, Giuseppe; Edkins, E.; Empl, Anton; Fan, A.; Fiorillo, G.; Fomenko, K.; Forster, G.; Franco, D.; Gabriele, F.; Galbiati, C.; Giganti, C.; Goretti, A.; Granato, Francesco; Grandi, L.; Gromov, M.; Guan, M. Y.; Guardincerri, Y.; Hackett, B.; Herner, K.; Hungerford, Edward; Ianni, Al.; Ianni, An.; James, I.; Jollet, C.; Keeter, K.; Kendziora, C.; Kobychev, V.; Koh, G.; Korablev, D.; Korga, G.; Kubankin, Alexander; Li, X.; Lissia, M.; Lombardi, P.; Luitz, S.; Ma, Y. Q.; Machulin, I.; Mandarano, A.; Mari, S. M.; Maricic, J.; Marini, L.; Martoff, J.; Meregaglia, A.; Meyers, P. D.; Miletic, T.; Milincic, R.; Montanari, D.; Monte, Alissa; Montuschi, M.; Monzani, M. E.; Mosteiro, P.; Mount, B.; Muratova, V.; Musico, P.; Napolitano, James; Nelson, A.; Odrowski, S.; Orsini, M.; Ortica, F.; Pagani, L.; Pallavicini, Marco; Pantic, E.; Parmeggiano, S.; Pelczar, K.; Pelliccia, N.; Perasso, S.; Pocar, A.; Pordes, S.; Pugachev, D.; Qian, H.; Randle, K.; Ranucci, Gioacchino; Razeto, A.; Reinhold, B.; Renshaw, Andrew; Romani, A.; Rossi, B.; Rossi, N.; Rountree, S. D.; Sablone, D.; Saggese, P.; Saldanha, R.; Sands, W.; Sangiorgio, Samuele; Savarese, Claudio; Segreto, E.; Semenov, D.; Shields, E.; Singh, Parth; Skorokhvatov, Mikhail; Smirnov, Oleg; Sotnikov, Albert; Stanford, Chris; Suvorov, Yura; Tartaglia, Roberto; Tatarowicz, John; Testera, Gemma; Tonazzo, Alessandra; Trinchese, P.; Unzhakov, Eugenii; Vishneva, Alina; Vogelaar, R. B.; Wada, Masayuki; Walker, Susan E.; Wang, H.; Wang, Y.; Watson, A. W.; Westerdale, S.; Wilhelmi, James; Wojcik, M.; Xiang, Xin; Xu, Jingke; Yang, C. G.; Yoo, J.; Zavatarelli, Sandra; Zec, Adam; Zhong, W. L.; Zhu, Chengliang; Zuzel, G.

    2016-02-01

    DarkSide is a graded experimental project based on radiopure argon, and is now, and will be, used in direct dark matter searches. The present DarkSide-50 detector, operating at the Gran Sasso National Laboratory, is a dual-phase, 50 kg, liquid argon time-projection-chamber surrounded by an active liquid scintillator veto. It is designed to be background free in 3 years of operation. DS-50 performances, when filled with atmospheric argon, are reported. However DS-50 filled with underground argon, shows impressive reduction of the 39Ar isotope. The application of this powerful technology in a future generation of the DarkSide program is discussed.

  16. Cost-Minimizing Scheduling of Workflows on a Cloud of Memory Managed Multicore Machines

    Science.gov (United States)

    Grounds, Nicolas G.; Antonio, John K.; Muehring, Jeff

    Workflows are modeled as hierarchically structured directed acyclic graphs in which vertices represent computational tasks, referred to as requests, and edges represent precedent constraints among requests. Associated with each workflow is a deadline that defines the time by which all computations of a workflow should be complete. Workflows are submitted by numerous clients to a scheduler that assigns workflow requests to a cloud of memory managed multicore machines for execution. A cost function is assumed to be associated with each workflow, which maps values of relative workflow tardiness to corresponding cost function values. A novel cost-minimizing scheduling framework is introduced to schedule requests of workflows so as to minimize the sum of cost function values for all workflows. The utility of the proposed scheduler is compared to another previously known scheduling policy.

  17. Prediction of Machine Tool Condition Using Support Vector Machine

    Science.gov (United States)

    Wang, Peigong; Meng, Qingfeng; Zhao, Jian; Li, Junjie; Wang, Xiufeng

    2011-07-01

    Condition monitoring and predicting of CNC machine tools are investigated in this paper. Considering the CNC machine tools are often small numbers of samples, a condition predicting method for CNC machine tools based on support vector machines (SVMs) is proposed, then one-step and multi-step condition prediction models are constructed. The support vector machines prediction models are used to predict the trends of working condition of a certain type of CNC worm wheel and gear grinding machine by applying sequence data of vibration signal, which is collected during machine processing. And the relationship between different eigenvalue in CNC vibration signal and machining quality is discussed. The test result shows that the trend of vibration signal Peak-to-peak value in surface normal direction is most relevant to the trend of surface roughness value. In trends prediction of working condition, support vector machine has higher prediction accuracy both in the short term ('One-step') and long term (multi-step) prediction compared to autoregressive (AR) model and the RBF neural network. Experimental results show that it is feasible to apply support vector machine to CNC machine tool condition prediction.

  18. Workload-aware request routing in cloud data center using software-defined networking

    Institute of Scientific and Technical Information of China (English)

    Haitao Yuan; Jing Bi; Bohu Li

    2015-01-01

    Large latency of applications wil bring revenue loss to cloud infrastructure providers in the cloud data center. The existing control ers of software-defined networking architecture can fetch and process traffic information in the network. Therefore, the con-trol ers can only optimize the network latency of applications. How-ever, the serving latency of applications is also an important factor in delivered user-experience for arrival requests. Unintel igent re-quest routing wil cause large serving latency if arrival requests are al ocated to overloaded virtual machines. To deal with the re-quest routing problem, this paper proposes the workload-aware software-defined networking control er architecture. Then, request routing algorithms are proposed to minimize the total round trip time for every type of request by considering the congestion in the network and the workload in virtual machines (VMs). This paper final y provides the evaluation of the proposed algorithms in a sim-ulated prototype. The simulation results show that the proposed methodology is efficient compared with the existing approaches.

  19. Server-side Statistics Scripting in PHP

    Directory of Open Access Journals (Sweden)

    Jan de Leeuw

    1997-06-01

    Full Text Available On the UCLA Statistics WWW server there are a large number of demos and calculators that can be used in statistics teaching and research. Some of these demos require substantial amounts of computation, others mainly use graphics. These calculators and demos are implemented in various different ways, reflecting developments in WWW based computing. As usual, one of the main choices is between doing the work on the client-side (i.e. in the browser or on the server-side (i.e. on our WWW server. Obviously, client-side computation puts fewer demands on the server. On the other hand, it requires that the client downloads Java applets, or installs plugins and/or helpers. If JavaScript is used, client-side computations will generally be slow. We also have to assume that the client is installed properly, and has the required capabilities. Requiring too much on the client-side has caused browsing machines such as Netscape Communicator to grow beyond all reasonable bounds, both in size and RAM requirements. Moreover requiring Java and JavaScript rules out such excellent browsers as Lynx or Emacs W3. For server-side computing, we can configure the server and its resources ourselves, and we need not worry about browser capabilities and configuration. Nothing needs to be downloaded, except the usual HTML pages and graphics. In the same way as on the client side, there is a scripting solution, where code is interpreted, or a ob ject-code solution using compiled code. For the server-side scripting, we use embedded languages, such as PHP/FI. The scripts in the HTML pages are interpreted by a CGI program, and the output of the CGI program is send to the clients. Of course the CGI program is compiled, but the statistics procedures will usually be interpreted, because PHP/FI does not have the appropriate functions in its scripting language. This will tend to be slow, because embedded languages do not deal efficiently with loops and similar constructs. Thus a first

  20. SEAMLESS TECHNOLOGY ON CIRCULAR KNITTING MACHINES

    Directory of Open Access Journals (Sweden)

    CRETU Viorica

    2014-05-01

    Full Text Available With industrial progress, the advancements in garment manufacturing have evolved from cut & sew to complete garment knitting, which produces one entire garment without sewing or linking process. Seamless knitting technology is similar to sock manufacture, the specialized circular knitting machines producing 3 dimensional garments with no side seams, with the waistband integrated with body of the garment and with knitted washing instructions and logos. The paper starts by presenting the main advantages of seamless garments but also some limitations because the technology. Because for a seamless garment, which is realized as a knitted tub, is very important to ensure the required final chest size, it was presented the main components involved: the knitting machine, the garment design and the yarns used. The knitting machines, beside the values of diameters and gauges with a great impact on the chest size, are characterized by a very innovative and complex construction. The design of a seamless garment is fundamental different compared to garments produced on a traditional way because the designer must to work backwards from a finished garment to create the knitting programme that will ultimately give the correct finished size. On the end of the paper it was presented some of the applications of the seamless products that cover intimate apparel and other bodywear, outwear, activewear and functional sportswear, upholstery, industrial, automotive and medical textiles.

  1. A Boltzmann machine for the organization of intelligent machines

    Science.gov (United States)

    Moed, Michael C.; Saridis, George N.

    1989-01-01

    In the present technological society, there is a major need to build machines that would execute intelligent tasks operating in uncertain environments with minimum interaction with a human operator. Although some designers have built smart robots, utilizing heuristic ideas, there is no systematic approach to design such machines in an engineering manner. Recently, cross-disciplinary research from the fields of computers, systems AI and information theory has served to set the foundations of the emerging area of the design of intelligent machines. Since 1977 Saridis has been developing an approach, defined as Hierarchical Intelligent Control, designed to organize, coordinate and execute anthropomorphic tasks by a machine with minimum interaction with a human operator. This approach utilizes analytical (probabilistic) models to describe and control the various functions of the intelligent machine structured by the intuitively defined principle of Increasing Precision with Decreasing Intelligence (IPDI) (Saridis 1979). This principle, even though resembles the managerial structure of organizational systems (Levis 1988), has been derived on an analytic basis by Saridis (1988). The purpose is to derive analytically a Boltzmann machine suitable for optimal connection of nodes in a neural net (Fahlman, Hinton, Sejnowski, 1985). Then this machine will serve to search for the optimal design of the organization level of an intelligent machine. In order to accomplish this, some mathematical theory of the intelligent machines will be first outlined. Then some definitions of the variables associated with the principle, like machine intelligence, machine knowledge, and precision will be made (Saridis, Valavanis 1988). Then a procedure to establish the Boltzmann machine on an analytic basis will be presented and illustrated by an example in designing the organization level of an Intelligent Machine. A new search technique, the Modified Genetic Algorithm, is presented and proved

  2. Coping – Late Side Effects

    Science.gov (United States)

    Cancer treatment can cause late side effects that may not show up for months or years after treatment. These late effects may include heart and lung problems, bone loss, eye and hearing changes, lymphedema, and other problems

  3. Managing Chemotherapy Side Effects: Constipation

    Science.gov (United States)

    N ational C ancer I nstitute Managing Chemotherapy Side Effects Constipation Take these steps: Eat high-fiber foods such as: ● ● Whole-grain breads and cereals ● ● Fruits and vegetables ● ● Nuts and seeds ...

  4. Engineering molecular machines

    Science.gov (United States)

    Erman, Burak

    2016-04-01

    Biological molecular motors use chemical energy, mostly in the form of ATP hydrolysis, and convert it to mechanical energy. Correlated thermal fluctuations are essential for the function of a molecular machine and it is the hydrolysis of ATP that modifies the correlated fluctuations of the system. Correlations are consequences of the molecular architecture of the protein. The idea that synthetic molecular machines may be constructed by designing the proper molecular architecture is challenging. In their paper, Sarkar et al (2016 New J. Phys. 18 043006) propose a synthetic molecular motor based on the coarse grained elastic network model of proteins and show by numerical simulations that motor function is realized, ranging from deterministic to thermal, depending on temperature. This work opens up a new range of possibilities of molecular architecture based engine design.

  5. Boosting Support Vector Machines

    Directory of Open Access Journals (Sweden)

    Elkin Eduardo García Díaz

    2006-11-01

    Full Text Available En este artículo, se presenta un algoritmo de clasificación binaria basado en Support Vector Machines (Máquinas de Vectores de Soporte que combinado apropiadamente con técnicas de Boosting consigue un mejor desempeño en cuanto a tiempo de entrenamiento y conserva características similares de generalización con un modelo de igual complejidad pero de representación más compacta./ In this paper we present an algorithm of binary classification based on Support Vector Machines. It is combined with a modified Boosting algorithm. It run faster than the original SVM algorithm with a similar generalization error and equal complexity model but it has more compact representation.

  6. Quo vadis, Intelligent Machine?

    Directory of Open Access Journals (Sweden)

    Rosemarie Velik

    2010-09-01

    Full Text Available Artificial Intelligence (AI is a branch of computer science concerned with making computers behave like humans. At least this was the original idea. However, it turned out that this is no task easy to be solved. This article aims to give a comprehensible review on the last 60 years of artificial intelligence taking a philosophical viewpoint. It is outlined what happened so far in AI, what is currently going on in this research area, and what can be expected in future. The goal is to mediate an understanding for the developments and changes in thinking in course of time about how to achieve machine intelligence. The clear message is that AI has to join forces with neuroscience and other brain disciplines in order to make a step towards the development of truly intelligent machines.

  7. Introduction to Machine Protection

    CERN Document Server

    Schmidt, R

    2016-01-01

    Protection of accelerator equipment is as old as accelerator technology and was for many years related to high-power equipment. Examples are the protection of powering equipment from overheating (magnets, power converters, high-current cables), of superconducting magnets from damage after a quench and of klystrons. The protection of equipment from beam accidents is more recent, although there was one paper that discussed beam-induced damage for the SLAC linac (Stanford Linear Accelerator Center) as early as in 1967. It is related to the increasing beam power of high-power proton accelerators, to the emission of synchrotron light by electron-positron accelerators and to the increase of energy stored in the beam. Designing a machine protection system requires an excellent understanding of accelerator physics and operation to anticipate possible failures that could lead to damage. Machine protection includes beam and equipment monitoring, a system to safely stop beam operation (e.g. dumping the beam or stopping ...

  8. Technological requirements of profile machining

    Institute of Scientific and Technical Information of China (English)

    PARK Sangchul; CHUNG Yunchan

    2006-01-01

    The term ‘profile machining’is used to refer to the milling of vertical surfaces described by profile curves. Profile machining requires higher precision (1/1000 mm) than regular 3D machining (1/100 mm) with the erosion of sharp vertices should being especially avoided. Although, profile machining is very essential for making trimming and flangedies, it seldom brought into focus. This paper addresses the technological requirements of profile machining including machining width and depth control,minimizing toolware, and protecting sharp vertices. Issues of controller alarms are also addressed.

  9. Machining fiber-reinforced composites

    Science.gov (United States)

    Komanduri, Ranga

    1993-04-01

    Compared to high tool wear and high costs of tooling of fiber-reinforced composites (FRCs), noncontact material-removal processes offer attractive alternative. Noncontact machining methods can also minimize dust, noise, and extensive plastic deformation and consequent heat generation associated with conventional machining of FRCs, espacially those with an epoxy matrix. The paper describes the principles involved in and the details of machining of FRCs by laser machining, water jet-cutting and abrasive water jet-cutting, and electrical discharge machining of composites, as well as the limitations of each method.

  10. Novel side branch ostial stent.

    Science.gov (United States)

    Chen, Shao-Liang; Lv, Shu-Zheng; Kwan, Tak W

    2009-04-01

    Bifurcation lesions are technically challenging and plagued by a high incidence of restenosis, especially at the side branch orifice, which results in a more frequent need for revascularization during the follow-up period. This report discusses two clinical experiences with a novel side branch ostial stent, the BIGUARD stent, designed for the treatment of bifurcation lesions; procedural success with no in-hospital complications was observed in types IVb and Ia lesions.

  11. Future database machine architectures

    OpenAIRE

    Hsiao, David K.

    1984-01-01

    There are many software database management systems available on many general-purpose computers ranging from micros to super-mainframes. Database machines as backened computers can offload the database management work from the mainframe so that we can retain the same mainframe longer. However, the database backend must also demonstrate lower cost, higher performance, and newer functionality. Some of the fundamental architecture issues in the design of high-performance and great-capacity datab...

  12. Machine Learning at Scale

    OpenAIRE

    Izrailev, Sergei; Stanley, Jeremy M.

    2014-01-01

    It takes skill to build a meaningful predictive model even with the abundance of implementations of modern machine learning algorithms and readily available computing resources. Building a model becomes challenging if hundreds of terabytes of data need to be processed to produce the training data set. In a digital advertising technology setting, we are faced with the need to build thousands of such models that predict user behavior and power advertising campaigns in a 24/7 chaotic real-time p...

  13. Cost of photochemical machining

    OpenAIRE

    Roy, Rajkumar; Allen, David; Zamora, Oscar

    2004-01-01

    Photochemical machining (PCM), also known as photoetching, photofabrication or photochemical milling, is a non-traditional manufacturing method based on the combination of photoresist imaging and chemical etching. PCM uses techniques similar to those employed for the production of printed circuit boards and silicon integrated circuits. The PCM industry plays a valuable worldwide role in the production of metal precision parts and decorative items. Parts produced by PCM are t...

  14. Austempered Ductile Iron Machining

    Science.gov (United States)

    Pilc, Jozef; Šajgalík, Michal; Holubják, Jozef; Piešová, Marianna; Zaušková, Lucia; Babík, Ondrej; Kuždák, Viktor; Rákoci, Jozef

    2015-12-01

    This article deals with the machining of cast iron. In industrial practice, Austempered Ductile Iron began to be used relatively recently. ADI is ductile iron that has gone through austempering to get improved properties, among which we can include strength, wear resistance or noise damping. This specific material is defined also by other properties, such as high elasticity, ductility and endurance against tenigue, which are the properties, that considerably make the tooling characteristic worse.

  15. Quantum Virtual Machine (QVM)

    Energy Technology Data Exchange (ETDEWEB)

    2016-11-18

    There is a lack of state-of-the-art HPC simulation tools for simulating general quantum computing. Furthermore, there are no real software tools that integrate current quantum computers into existing classical HPC workflows. This product, the Quantum Virtual Machine (QVM), solves this problem by providing an extensible framework for pluggable virtual, or physical, quantum processing units (QPUs). It enables the execution of low level quantum assembly codes and returns the results of such executions.

  16. Agent Based Computing Machine

    Science.gov (United States)

    2005-12-09

    be used in Phase 2 to accomplish the following enhancements. Due to the speed and support of MPI for C/C++ on Beowulf clusters , these languages could...1.7 ABC Machine Formal Definition 24 1.8 Computational Analysis 31 1.9 Programming Concepts 34 1.10 Cluster Mapping 38 1.11 Phase 1 Results 43 2...options for hardware implementation are explored including an emulation with a high performance cluster , a high performance silicon chip and the

  17. Magnetic Electrochemical Finishing Machining

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    How to improve the finishing efficiency and surface roughness have been all along the objective of research in electrochemical polishing. However, the research activity, i.e. during electrochemical polishing, directly introduce the magnetic field to study how the magnetic field influences on the finishing efficiency, quality and the electrochemical process in the field of finishing machining technology, is insufficient. When introducing additional magnetic field in the traditional electrochemical pol...

  18. FMS precision machining

    Energy Technology Data Exchange (ETDEWEB)

    Burnham, M.W.

    1980-01-01

    In evaluating the technical obstacles and accuracy limits to producing a Precision Flexible Manufacturing System, a current system is subjected to an error budget analysis. It is noted that to make complex part geometries with tolerances in the lower thousandths range, machining to tenths is required for process control. Actual parts made to tenths are illustrated, along with a discussion of the requirements for automation and for process control.

  19. Machine on Trial

    Science.gov (United States)

    2012-06-01

    front of the Judge, how did we come to justify the ethical use of such a machine? The Judge called for a recess so that he could further educate ...commerce, where money would change hands, or for the purposes of controlling critical systems.”29 The initial group that set up the ARPANET did not... EBook of Fundamental Principals of the Metaphysic of Morals, May, 2004 [ EBook #5682 translated by Thomas Kingsmill Abbott, 12. http://manybooks.net

  20. Electrochemical Discharge Machining Process

    Directory of Open Access Journals (Sweden)

    Anjali V. Kulkarni

    2007-09-01

    Full Text Available Electrochemical discharge machining process is evolving as a promising micromachiningprocess. The experimental investigations in the present work substantiate this trend. In the presentwork, in situ, synchronised, transient temperature and current measurements have been carriedout. The need for the transient measurements arose due to the time-varying nature of the dischargeformation and time varying circuit current. Synchronised and transient measurements revealedthe discrete nature of the process. It also helped in formulating the basic mechanism for thedischarge formation and the material removal in the process. Temperature profile on workpieceand in electrochemical discharge machining cell is experimentally measured using pyrometer,and two varieties of K-type thermocouples. Surface topography of the discharge-affected zoneson the workpiece has been carried out using scanning electron microscope. Measurements andsurface topographical studies reveal the potential use of this process for machining in micronregime. With careful experimental set-up design, suitable supply voltage and its polarity, theprocess can be applied for both micromachining and micro-deposition. It can be extended formachining and or deposition of wide range of materials.

  1. Introduction: Minds, Bodies, Machines

    Directory of Open Access Journals (Sweden)

    Deirdre Coleman

    2008-10-01

    Full Text Available This issue of 19 brings together a selection of essays from an interdisciplinary conference on 'Minds, Bodies, Machines' convened last year by Birkbeck's Centre for Nineteenth-Century Studies, University of London, in partnership with the English programme, University of Melbourne and software developers Constraint Technologies International (CTI. The conference explored the relationship between minds, bodies and machines in the long nineteenth century, with a view to understanding the history of our technology-driven, post-human visions. It is in the nineteenth century that the relationship between the human and the machine under post-industrial capitalism becomes a pervasive theme. From Blake on the mills of the mind by which we are enslaved, to Carlyle's and Arnold's denunciation of the machinery of modern life, from Dickens's sooty fictional locomotive Mr Pancks, who 'snorted and sniffed and puffed and blew, like a little labouring steam-engine', and 'shot out […]cinders of principles, as if it were done by mechanical revolvency', to the alienated historical body of the late-nineteenth-century factory worker under Taylorization, whose movements and gestures were timed, regulated and rationalised to maximize efficiency; we find a cultural preoccupation with the mechanisation of the nineteenth-century human body that uncannily resonates with modern dreams and anxieties around technologies of the human.

  2. Machine Learning in Medicine.

    Science.gov (United States)

    Deo, Rahul C

    2015-11-17

    Spurred by advances in processing power, memory, storage, and an unprecedented wealth of data, computers are being asked to tackle increasingly complex learning tasks, often with astonishing success. Computers have now mastered a popular variant of poker, learned the laws of physics from experimental data, and become experts in video games - tasks that would have been deemed impossible not too long ago. In parallel, the number of companies centered on applying complex data analysis to varying industries has exploded, and it is thus unsurprising that some analytic companies are turning attention to problems in health care. The purpose of this review is to explore what problems in medicine might benefit from such learning approaches and use examples from the literature to introduce basic concepts in machine learning. It is important to note that seemingly large enough medical data sets and adequate learning algorithms have been available for many decades, and yet, although there are thousands of papers applying machine learning algorithms to medical data, very few have contributed meaningfully to clinical care. This lack of impact stands in stark contrast to the enormous relevance of machine learning to many other industries. Thus, part of my effort will be to identify what obstacles there may be to changing the practice of medicine through statistical learning approaches, and discuss how these might be overcome.

  3. Soft computing in machine learning

    CERN Document Server

    Park, Jooyoung; Inoue, Atsushi

    2014-01-01

    As users or consumers are now demanding smarter devices, intelligent systems are revolutionizing by utilizing machine learning. Machine learning as part of intelligent systems is already one of the most critical components in everyday tools ranging from search engines and credit card fraud detection to stock market analysis. You can train machines to perform some things, so that they can automatically detect, diagnose, and solve a variety of problems. The intelligent systems have made rapid progress in developing the state of the art in machine learning based on smart and deep perception. Using machine learning, the intelligent systems make widely applications in automated speech recognition, natural language processing, medical diagnosis, bioinformatics, and robot locomotion. This book aims at introducing how to treat a substantial amount of data, to teach machines and to improve decision making models. And this book specializes in the developments of advanced intelligent systems through machine learning. It...

  4. Machine Translation Effect on Communication

    DEFF Research Database (Denmark)

    Jensen, Mika Yasuoka; Bjørn, Pernille

    2011-01-01

    Intercultural collaboration facilitated by machine translation has gradually spread in various settings. Still, little is known as for the practice of machine-translation mediated communication. This paper investigates how machine translation affects intercultural communication in practice. Based...... determines communication process largely, our data indicates communication relies more on a dynamic process where participants establish common ground than on reproducibility and grammatical accuracy.......Intercultural collaboration facilitated by machine translation has gradually spread in various settings. Still, little is known as for the practice of machine-translation mediated communication. This paper investigates how machine translation affects intercultural communication in practice. Based...... on communication in which multilingual communication system is applied, we identify four communication types and its’ influences on stakeholders’ communication process, especially focusing on establishment and maintenance of common ground. Different from our expectation that quality of machine translation results...

  5. The Moon's near side megabasin and far side bulge

    CERN Document Server

    Byrne, Charles

    2013-01-01

    Since Luna and Lunar Orbiter photographed the far side of the Moon, the mysterious dichotomy between the face of the Moon as we see it from Earth and the side of the Moon that is hidden has puzzled lunar scientists. As we learned more from the Apollo sample return missions and later robotic satellites, the puzzle literally deepened, showing asymmetry of the crust and mantle, all the way to the core of the Moon. This book summarizes the author’s successful search for an ancient impact feature, the Near Side Megabasin of the Moon and the extensions to impact theory needed to find it. The implications of this ancient event are developed to answer many of the questions about the history of the Moon.

  6. Wake flow behind two side-by-side square cylinders

    Energy Technology Data Exchange (ETDEWEB)

    Yen, Shun C., E-mail: scyen@mail.ntou.edu.t [Department of Mechanical and Mechatronic Engineering, National Taiwan Ocean University, Keelung 202, Taiwan (China); Liu, Jung H. [Department of Mechanical and Mechatronic Engineering, National Taiwan Ocean University, Keelung 202, Taiwan (China)

    2011-02-15

    This study investigates the flow structures, form drag coefficients and vortex-shedding characteristics behind a single-square cylinder and two side-by-side cylinders in an open-loop wind tunnel. The Reynolds number (Re) and gap ratio (g*) are 2262 < Re < 28,000 and 0 {<=} g* {<=} 12, respectively. The flow patterns around the square cylinders are determined using the smoke-wire scheme. Experimental results indicate that the flow structures behind two side-by-side square cylinders are classified into three modes -single mode, gap-flow mode and couple vortex-shedding. The gap-flow mode displays anti-phase vortex shedding induced from the interference between the two square cylinders. However, the couple vortex-shedding mode exhibits in-phase vortex shedding that is caused by the independent flow behavior behind each square cylinder. The surface-pressure profile, form drag coefficient for each square cylinder (C{sub D}-bar) and vortex-shedding frequency were measured and calculated using a pressure transducer and a hot-wire anemometer. For two side-by-side cylinder configurations, the maximum C{sub D}-bar of 2.24 occurs in the single mode, while the minimum C{sub D}-bar of 1.68 occurs in the gap-flow mode. Additionally, the C{sub D}-bar in the coupled vortex-shedding mode is intermediate and approximately equal to that of a single (isolated) square cylinder. Moreover, the single mode has the highest Strouhal number (St) and the gap-flow mode has the lowest St.

  7. Drug side effect extraction from clinical narratives of psychiatry and psychology patients.

    Science.gov (United States)

    Sohn, Sunghwan; Kocher, Jean-Pierre A; Chute, Christopher G; Savova, Guergana K

    2011-12-01

    To extract physician-asserted drug side effects from electronic medical record clinical narratives. Pattern matching rules were manually developed through examining keywords and expression patterns of side effects to discover an individual side effect and causative drug relationship. A combination of machine learning (C4.5) using side effect keyword features and pattern matching rules was used to extract sentences that contain side effect and causative drug pairs, enabling the system to discover most side effect occurrences. Our system was implemented as a module within the clinical Text Analysis and Knowledge Extraction System. The system was tested in the domain of psychiatry and psychology. The rule-based system extracting side effects and causative drugs produced an F score of 0.80 (0.55 excluding allergy section). The hybrid system identifying side effect sentences had an F score of 0.75 (0.56 excluding allergy section) but covered more side effect and causative drug pairs than individual side effect extraction. The rule-based system was able to identify most side effects expressed by clear indication words. More sophisticated semantic processing is required to handle complex side effect descriptions in the narrative. We demonstrated that our system can be trained to identify sentences with complex side effect descriptions that can be submitted to a human expert for further abstraction. Our system was able to extract most physician-asserted drug side effects. It can be used in either an automated mode for side effect extraction or semi-automated mode to identify side effect sentences that can significantly simplify abstraction by a human expert.

  8. The Effects of Different Electrode Types for Obtaining Surface Machining Shape on Shape Memory Alloy Using Electrochemical Machining

    Science.gov (United States)

    Choi, S. G.; Kim, S. H.; Choi, W. K.; Moon, G. C.; Lee, E. S.

    2017-06-01

    Shape memory alloy (SMA) is important material used for the medicine and aerospace industry due to its characteristics called the shape memory effect, which involves the recovery of deformed alloy to its original state through the application of temperature or stress. Consumers in modern society demand stability in parts. Electrochemical machining is one of the methods for obtained these stabilities in parts requirements. These parts of shape memory alloy require fine patterns in some applications. In order to machine a fine pattern, the electrochemical machining method is suitable. For precision electrochemical machining using different shape electrodes, the current density should be controlled precisely. And electrode shape is required for precise electrochemical machining. It is possible to obtain precise square holes on the SMA if the insulation layer controlled the unnecessary current between electrode and workpiece. If it is adjusting the unnecessary current to obtain the desired shape, it will be a great contribution to the medical industry and the aerospace industry. It is possible to process a desired shape to the shape memory alloy by micro controlling the unnecessary current. In case of the square electrode without insulation layer, it derives inexact square holes due to the unnecessary current. The results using the insulated electrode in only side show precise square holes. The removal rate improved in case of insulated electrode than others because insulation layer concentrate the applied current to the machining zone.

  9. Helpdesk troubleshooting requests

    CERN Multimedia

    2006-01-01

    We should like to remind all CERN users that the FM Help Desk handles all work and repair requests and other enquiries relating to CERN's tertiary buildings, in particular the following systems and equipment: Electricity and lighting in office buildings, halls and workshops Heating, ventilation and air conditioning in office buildings, halls and workshops Lifts (excluding those in underground areas) Motorised doors Buildings and their equipment: roofs, doors, windows, blinds, etc. Plumbing Toilets Cleaning (all buildings and underground areas) Restaurant equipment Roads and green areas Waste collection The FM Helpdesk is open between 7.30 a.m. and 6.30 p.m. and can be contacted on Tel. 77777 or by e-mail (Fm.Support@cern.ch). Troubleshooting requests, complaints and work requests will only be accepted during these hours. Outside these hours and for any problems relating to non-tertiary buildings or to equipment not included in the above list, please contact the TI Control Room on Tel. 72201, 24 hours a d...

  10. An alternate side coupled structure for the Fermilab LINAC upgrade

    Energy Technology Data Exchange (ETDEWEB)

    Jurgens, T.G.; Kerns, Q.A.; Fritz, J.R.; May, M.A.

    1988-10-01

    An alternate side coupled structure (SCS) is being investigated. Comparisons are made to the traditional SCS. Mechanical comparisons include the relative cost and ease of fabrication. This discussion also addresses the use of CNC machining. Electrical comparisons include field distributions and coupling constants. Measured and numerical data are presented. The coupling constant of the alternate SCS is adjusted by independently changing either the separation of the coupling and accelerating cavity centers or the length of the slot. These two parameters are not independent in the traditional SCS design. 4 refs., 5 figs

  11. Advanced Machine learning Algorithm Application for Rotating Machine Health Monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Kanemoto, Shigeru; Watanabe, Masaya [The University of Aizu, Aizuwakamatsu (Japan); Yusa, Noritaka [Tohoku University, Sendai (Japan)

    2014-08-15

    The present paper tries to evaluate the applicability of conventional sound analysis techniques and modern machine learning algorithms to rotating machine health monitoring. These techniques include support vector machine, deep leaning neural network, etc. The inner ring defect and misalignment anomaly sound data measured by a rotating machine mockup test facility are used to verify the above various kinds of algorithms. Although we cannot find remarkable difference of anomaly discrimination performance, some methods give us the very interesting eigen patterns corresponding to normal and abnormal states. These results will be useful for future more sensitive and robust anomaly monitoring technology.

  12. Social identity performance : Extending the strategic side of SIDE

    NARCIS (Netherlands)

    Klein, Olivier; Spears, Russell; Reicher, Stephen

    This article extends the social identity model of deindividuation effects (SIDE) by considering the various ways in which relations of visibility to an audience can affect the public expression of identity-relevant norms (identity performance). It is suggested that social identity performance can

  13. Side Effects of Side Effects Information in Drug Information Leaflets.

    Science.gov (United States)

    Maat, H. Pander; Klaassen, R.

    1994-01-01

    Describes a study in which drug information leaflets given to patients were improved in two ways, first by adding a short introductory paragraph on the nature of side effects generally, and second by adjusting frequency descriptors to more accurately reflect pretesting of the drug. Explains that participants in the study were less likely to…

  14. Running away from side effects

    DEFF Research Database (Denmark)

    Casla, S; Hojman, P; Márquez-Rodas, I

    2015-01-01

    be an integrative complementary intervention to improve physiological, physical and psychological factors that affect survival and quality of life of these patients. For that reason, the main objective of this review is to provide a general overview of exercise benefits in breast cancer patients and recommendations......The number of breast cancer survivors increases every year, thanks to the development of new treatments and screening techniques. However, patients present with numerous side effects that may affect their quality of life. Exercise has been demonstrated to reduce some of these side effects......, but in spite of this, few breast cancer patients know and follow the exercise recommendations needed to remain healthy. In this review, we describe the different breast cancer treatments and the related side effects and implications of exercise in relation to these. We propose that exercise could...

  15. Experimental determination of demand side management potential of wet appliances in the Netherlands

    NARCIS (Netherlands)

    Staats, M. R.; de Boer-Meulman, P. D M; van Sark, W. G J H M

    2017-01-01

    The potential of demand side management (DSM) of wet appliances (washing machine, dishwasher and tumble dryer) in households with photovoltaic (PV) systems is studied experimentally focusing on evening peak demand reduction and increase in PV self-consumption. In a sample of 100 Dutch households the

  16. Experimental determination of demand side management potential of wet appliances in the Netherlands

    NARCIS (Netherlands)

    Staats, M. R.; de Boer-Meulman, P. D M; van Sark, W. G J H M

    2017-01-01

    The potential of demand side management (DSM) of wet appliances (washing machine, dishwasher and tumble dryer) in households with photovoltaic (PV) systems is studied experimentally focusing on evening peak demand reduction and increase in PV self-consumption. In a sample of 100 Dutch households the

  17. Diamond Measuring Machine

    Energy Technology Data Exchange (ETDEWEB)

    Krstulic, J.F.

    2000-01-27

    The fundamental goal of this project was to develop additional capabilities to the diamond measuring prototype, work out technical difficulties associated with the original device, and perform automated measurements which are accurate and repeatable. For this project, FM and T was responsible for the overall system design, edge extraction, and defect extraction and identification. AccuGem provided a lab and computer equipment in Lawrence, 3D modeling, industry expertise, and sets of diamonds for testing. The system executive software which controls stone positioning, lighting, focusing, report generation, and data acquisition was written in Microsoft Visual Basic 6, while data analysis and modeling were compiled in C/C++ DLLs. All scanning parameters and extracted data are stored in a central database and available for automated analysis and reporting. The Phase 1 study showed that data can be extracted and measured from diamond scans, but most of the information had to be manually extracted. In this Phase 2 project, all data required for geometric modeling and defect identification were automatically extracted and passed to a 3D modeling module for analysis. Algorithms were developed which automatically adjusted both light levels and stone focus positioning for each diamond-under-test. After a diamond is analyzed and measurements are completed, a report is printed for the customer which shows carat weight, summarizes stone geometry information, lists defects and their size, displays a picture of the diamond, and shows a plot of defects on a top view drawing of the stone. Initial emphasis of defect extraction was on identification of feathers, pinpoints, and crystals. Defects were plotted color-coded by industry standards for inclusions (red), blemishes (green), and unknown defects (blue). Diamonds with a wide variety of cut quality, size, and number of defects were tested in the machine. Edge extraction, defect extraction, and modeling code were tested for

  18. Tribology in machine design

    CERN Document Server

    Stolarski, T A

    1990-01-01

    Tribology in Machine Design aims to promote a better appreciation of the increasingly important role played by tribology at the design stage in engineering. This book shows how algorithms developed from the basic principles of tribology can be used in a range of practical applications. The concept of tribodesign is introduced in Chapter 1. Chapter 2 is devoted to a brief discussion of the basic principles of tribology, including some concepts and models of lubricated wear and friction under complex kinematic conditions. Elements of contact mechanics, presented in Chapter 3, are confined to the

  19. Quantum adiabatic machine learning

    CERN Document Server

    Pudenz, Kristen L

    2011-01-01

    We develop an approach to machine learning and anomaly detection via quantum adiabatic evolution. In the training phase we identify an optimal set of weak classifiers, to form a single strong classifier. In the testing phase we adiabatically evolve one or more strong classifiers on a superposition of inputs in order to find certain anomalous elements in the classification space. Both the training and testing phases are executed via quantum adiabatic evolution. We apply and illustrate this approach in detail to the problem of software verification and validation.

  20. Daphne machine project

    Energy Technology Data Exchange (ETDEWEB)

    Vignola, G. and Daphne Project Team [Istituto Nazionale di Fisica Nucleare, Frascati (Italy)

    1996-07-01

    Daphne, a high luminosity e{sup +}/e{sup -} {Phi} factory, is presently under construction in Frascati. The beginning of the collider commissioning is scheduled by winter 1997, with a short term luminosity goal L=1.3 10{sup 32} cm{sup -2} sec{sup -1}. Daphne shall be the first of the new generation of very high luminosity colliders, called factories, to come in operation. Other factories under construction are PEP-II and KEK-B: first collision, for both machines, is planned for 1998.

  1. CENTRIFUGAL CASTING MACHINE

    Science.gov (United States)

    Shuck, A.B.

    1958-04-01

    A device is described that is specifically designed to cast uraniumn fuel rods in a vacuunn, in order to obtain flawless, nonoxidized castings which subsequently require a maximum of machining or wastage of the expensive processed material. A chamber surrounded with heating elements is connected to the molds, and the entire apparatus is housed in an airtight container. A charge of uranium is placed in the chamber, heated, then is allowed to flow into the molds While being rotated. Water circulating through passages in the molds chills the casting to form a fine grained fuel rod in nearly finished form.

  2. Electrical machines with Matlab

    CERN Document Server

    Gonen, Turan

    2011-01-01

    Basic ConceptsDistribution SystemImpact of Dispersed Storage and GenerationBrief Overview of Basic Electrical MachinesReal and Reactive Powers in Single-Phase AC CircuitsThree-Phase CircuitsThree-Phase SystemsUnbalanced Three-Phase LoadsMeasurement of Average Power in Three-Phase CircuitsPower Factor CorrectionMagnetic CircuitsMagnetic Field of Current-Carrying ConductorsAmpère's Magnetic Circuital LawMagnetic CircuitsMagnetic Circuit with Air GapBrief Review of FerromagnetismMagnetic Core LossesHow to Determine Flux for a Given MMFPermanent MagnetsTransformersTransformer ConstructionBrief Rev

  3. Patterns in clinical chemistry requests

    OpenAIRE

    Hemel, Jan B.; Hindriks, Frans R.; van der Voet, Hilko; Rijnveld, Leo R.

    1989-01-01

    For each patient sample that is presented to the clinical chemistry laboratory a combination of various tests can be requested. This combination or profile will depend on the condition of the patient, and hence also on the requesting hospital department. Several techniques were applied to detect and describe patterns in tests requested by the cardiology, hepatology and nephrology sections of the out-patient's Department for Internal Medicine. Comparison of the frequencies of ordering the test...

  4. A Typology of Multi-sided Platforms

    DEFF Research Database (Denmark)

    Staykova, Kalina Stefanova; Damsgaard, Jan

    2015-01-01

    which evolved several steps into being multi-sided (Facebook). Our analysis shows a structural difference between one-sided, two-sided and multi-sided platforms and that platforms consist of a core and potentially also a periphery. The sides of a platform and the ties which connect them can be arranged...

  5. Dark Side of the Universe

    CERN Document Server

    2016-01-01

    The Dark Side of the Universe (DSU) workshops bring together a wide range of theorists and experimentalists to discuss current ideas on models of the dark side, and relate them to current and future experiments. This year's DSU will take place in the colorful Norwegian city of Bergen. Topics include dark matter, dark energy, cosmology, and physics beyond the standard model. One of the goals of the workshop is to expose in particular students and young researchers to the fascinating topics of dark matter and dark energy, and to provide them with the opportunity to meet some of the best researchers in these areas .

  6. The Dark Side of Management

    DEFF Research Database (Denmark)

    Hanlon, Gerard; Dunne, Stephen; Johnsen, Christian Garmann

    2017-01-01

    Towards the end of 2015, the ephemera collective organised, chaired and participated within two separate Q+A panels celebrating the launch of Gerard Hanlon’s The dark side of management: A secret history of management theory. The events took place in The University of Leicester’s School of Manage......Towards the end of 2015, the ephemera collective organised, chaired and participated within two separate Q+A panels celebrating the launch of Gerard Hanlon’s The dark side of management: A secret history of management theory. The events took place in The University of Leicester’s School...

  7. Detecting Milling Deformation in 7075 Aluminum Alloy Aeronautical Monolithic Components Using the Quasi-Symmetric Machining Method

    Directory of Open Access Journals (Sweden)

    Qiong Wu

    2016-04-01

    Full Text Available The deformation of aeronautical monolithic components due to CNC machining is a bottle-neck issue in the aviation industry. The residual stress releases and redistributes in the process of material removal, and the distortion of the monolithic component is generated. The traditional one-side machining method will produce oversize deformation. Based on the three-stage CNC machining method, the quasi-symmetric machining method is developed in this study to reduce deformation by symmetry material removal using the M-symmetry distribution law of residual stress. The mechanism of milling deformation due to residual stress is investigated. A deformation experiment was conducted using traditional one-side machining method and quasi-symmetric machining method to compare with finite element method (FEM. The deformation parameters are validated by comparative results. Most of the errors are within 10%. The reason for these errors is determined to improve the reliability of the method. Moreover, the maximum deformation value of using quasi-symmetric machining method is within 20% of that of using the traditional one-side machining method. This result shows the quasi-symmetric machining method is effective in reducing deformation caused by residual stress. Thus, this research introduces an effective method for reducing the deformation of monolithic thin-walled components in the CNC milling process.

  8. Optimal online algorithms for scheduling on two identical machines under a grade of service

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    This work is aimed at investigating the online scheduling problem on two parallel and identical machines with a new feature that service requests from various customers are entitled to many different grade of service (GoS) levels, so each job and machine are labelled with the GoS levels, and each job can be processed by a particular machine only when its GoS level is no less than that of the machine. The goal is to minimize the makespan. For non-preemptive version, we propose an optimal online algorithm with competitive ratio 5/3. For preemptive version, we propose an optimal online algorithm with competitive ratio 3/2.

  9. Machining of Complex Sculptured Surfaces

    CERN Document Server

    2012-01-01

    The machining of complex sculptured surfaces is a global technological topic in modern manufacturing with relevance in both industrialized and emerging in countries particularly within the moulds and dies sector whose applications include highly technological industries such as the automotive and aircraft industry. Machining of Complex Sculptured Surfaces considers new approaches to the manufacture of moulds and dies within these industries. The traditional technology employed in the manufacture of moulds and dies combined conventional milling and electro-discharge machining (EDM) but this has been replaced with  high-speed milling (HSM) which has been applied in roughing, semi-finishing and finishing of moulds and dies with great success. Machining of Complex Sculptured Surfaces provides recent information on machining of complex sculptured surfaces including modern CAM systems and process planning for three and five axis machining as well as explanations of the advantages of HSM over traditional methods ra...

  10. Learning thermodynamics with Boltzmann machines

    Science.gov (United States)

    Torlai, Giacomo; Melko, Roger G.

    2016-10-01

    A Boltzmann machine is a stochastic neural network that has been extensively used in the layers of deep architectures for modern machine learning applications. In this paper, we develop a Boltzmann machine that is capable of modeling thermodynamic observables for physical systems in thermal equilibrium. Through unsupervised learning, we train the Boltzmann machine on data sets constructed with spin configurations importance sampled from the partition function of an Ising Hamiltonian at different temperatures using Monte Carlo (MC) methods. The trained Boltzmann machine is then used to generate spin states, for which we compare thermodynamic observables to those computed by direct MC sampling. We demonstrate that the Boltzmann machine can faithfully reproduce the observables of the physical system. Further, we observe that the number of neurons required to obtain accurate results increases as the system is brought close to criticality.

  11. Cesarean section by maternal request

    Directory of Open Access Journals (Sweden)

    RAPHAEL CÂMARA

    Full Text Available ABSTRACT Cesarean section by maternal request is the one performed on a pregnant woman without medical indication and without contraindication to vaginal delivery. There is great controversy over requested cesarean section. Potential risks include complications in subsequent pregnancies, such as uterine rupture, placenta previa and accreta. Potential benefits of requested cesareans include a lower risk of postpartum hemorrhage in the first cesarean and fewer surgical complications compared with vaginal delivery. Cesarean section by request should never be performed before 39 weeks.

  12. Novel Transverse Flux Machine for Vehicle Traction Applications: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Wan, Z.; Ahmed, A.; Husain, I.; Muljadi, E.

    2015-04-02

    A novel transverse flux machine topology for electric vehicle traction applications using ferrite magnets is presented in this paper. The proposed transverse flux topology utilizes novel magnet arrangements in the rotor that are similar to the Halbach array to boost flux linkage; on the stator side, cores are alternately arranged around a pair of ring windings in each phase to make use of the entire rotor flux that eliminates end windings. Analytical design considerations and finite-element methods are used for an optimized design of a scooter in-wheel motor. Simulation results from finite element analysis (FEA) show that the motor achieved comparable torque density to conventional rare-earth permanent magnet (PM) machines. This machine is a viable candidate for direct-drive applications with low cost and high torque density.

  13. Machine learning with R cookbook

    CERN Document Server

    Chiu, Yu-Wei

    2015-01-01

    If you want to learn how to use R for machine learning and gain insights from your data, then this book is ideal for you. Regardless of your level of experience, this book covers the basics of applying R to machine learning through to advanced techniques. While it is helpful if you are familiar with basic programming or machine learning concepts, you do not require prior experience to benefit from this book.

  14. Machine learning in healthcare informatics

    CERN Document Server

    Acharya, U; Dua, Prerna

    2014-01-01

    The book is a unique effort to represent a variety of techniques designed to represent, enhance, and empower multi-disciplinary and multi-institutional machine learning research in healthcare informatics. The book provides a unique compendium of current and emerging machine learning paradigms for healthcare informatics and reflects the diversity, complexity and the depth and breath of this multi-disciplinary area. The integrated, panoramic view of data and machine learning techniques can provide an opportunity for novel clinical insights and discoveries.

  15. Autocoding State Machine in Erlang

    DEFF Research Database (Denmark)

    Guo, Yu; Hoffman, Torben; Gunder, Nicholas

    2008-01-01

    This paper presents an autocoding tool suit, which supports development of state machine in a model-driven fashion, where models are central to all phases of the development process. The tool suit, which is built on the Eclipse platform, provides facilities for the graphical specification...... of a state machine model. Once the state machine is specified, it is used as input to a code generation engine that generates source code in Erlang....

  16. Stacked Extreme Learning Machines.

    Science.gov (United States)

    Zhou, Hongming; Huang, Guang-Bin; Lin, Zhiping; Wang, Han; Soh, Yeng Chai

    2015-09-01

    Extreme learning machine (ELM) has recently attracted many researchers' interest due to its very fast learning speed, good generalization ability, and ease of implementation. It provides a unified solution that can be used directly to solve regression, binary, and multiclass classification problems. In this paper, we propose a stacked ELMs (S-ELMs) that is specially designed for solving large and complex data problems. The S-ELMs divides a single large ELM network into multiple stacked small ELMs which are serially connected. The S-ELMs can approximate a very large ELM network with small memory requirement. To further improve the testing accuracy on big data problems, the ELM autoencoder can be implemented during each iteration of the S-ELMs algorithm. The simulation results show that the S-ELMs even with random hidden nodes can achieve similar testing accuracy to support vector machine (SVM) while having low memory requirements. With the help of ELM autoencoder, the S-ELMs can achieve much better testing accuracy than SVM and slightly better accuracy than deep belief network (DBN) with much faster training speed.

  17. Interaction with Machine Improvisation

    Science.gov (United States)

    Assayag, Gerard; Bloch, George; Cont, Arshia; Dubnov, Shlomo

    We describe two multi-agent architectures for an improvisation oriented musician-machine interaction systems that learn in real time from human performers. The improvisation kernel is based on sequence modeling and statistical learning. We present two frameworks of interaction with this kernel. In the first, the stylistic interaction is guided by a human operator in front of an interactive computer environment. In the second framework, the stylistic interaction is delegated to machine intelligence and therefore, knowledge propagation and decision are taken care of by the computer alone. The first framework involves a hybrid architecture using two popular composition/performance environments, Max and OpenMusic, that are put to work and communicate together, each one handling the process at a different time/memory scale. The second framework shares the same representational schemes with the first but uses an Active Learning architecture based on collaborative, competitive and memory-based learning to handle stylistic interactions. Both systems are capable of processing real-time audio/video as well as MIDI. After discussing the general cognitive background of improvisation practices, the statistical modelling tools and the concurrent agent architecture are presented. Then, an Active Learning scheme is described and considered in terms of using different improvisation regimes for improvisation planning. Finally, we provide more details about the different system implementations and describe several performances with the system.

  18. Vector control of induction machines

    CERN Document Server

    Robyns, Benoit

    2012-01-01

    After a brief introduction to the main law of physics and fundamental concepts inherent in electromechanical conversion, ""Vector Control of Induction Machines"" introduces the standard mathematical models for induction machines - whichever rotor technology is used - as well as several squirrel-cage induction machine vector-control strategies. The use of causal ordering graphs allows systematization of the design stage, as well as standardization of the structure of control devices. ""Vector Control of Induction Machines"" suggests a unique approach aimed at reducing parameter sensitivity for

  19. Beam Transfer and Machine Protection

    CERN Document Server

    Kain, V

    2016-01-01

    Beam transfer, such as injection into or extraction from an accelerator, is one of the most critical moments in terms of machine protection in a high-intensity machine. Special equipment is used and machine protection aspects have to be taken into account in the design of the beam transfer concepts. A brief introduction of the principles of beam transfer and the equipment involved will be given in this lecture. The main concepts of machine protection for injection and extraction will be presented, with examples from the CERN SPS and LHC.

  20. Turing Automata and Graph Machines

    Directory of Open Access Journals (Sweden)

    Miklós Bartha

    2010-06-01

    Full Text Available Indexed monoidal algebras are introduced as an equivalent structure for self-dual compact closed categories, and a coherence theorem is proved for the category of such algebras. Turing automata and Turing graph machines are defined by generalizing the classical Turing machine concept, so that the collection of such machines becomes an indexed monoidal algebra. On the analogy of the von Neumann data-flow computer architecture, Turing graph machines are proposed as potentially reversible low-level universal computational devices, and a truly reversible molecular size hardware model is presented as an example.

  1. Accuracy and Reliability of a New Tennis Ball Machine

    Directory of Open Access Journals (Sweden)

    Cyril Brechbuhl, Grégoire Millet, Laurent Schmitt

    2016-06-01

    Full Text Available The aim was to evaluate the reliability of a newly-developed ball machine named 'Hightof', on the field and to assess its accuracy. The experiment was conducted in the collaboration of the 'Hawk-Eye' technology. The accuracy and reliability of this ball machine were assessed during an incremental test, with 1 min of exercise and 30 sec of recovery, where the frequency of the balls increased from 10 to 30 balls·min-1. The initial frequency was 10 and increased by 2 until 22, then by 1 until 30 balls·min-1. The reference points for the impact were 8.39m from the net and 2.70m from lateral line for the right side and 2.83m for the left side. The precision of the machine was similar on the right and left sides (0.63 ± 0.39 vs 0.63 ± 0.34 m. The distances to the reference point were 0.52 ± 0.42, 0.26 ± 0.19, 0.52 ± 0.37, 0.28 ± 0.19 m for the Y-right, X-right, Y-left and X-left impacts. The precision was constant and did not increase with the intensity. (e.g ball frequency. The ball velocity was 86.3 ± 1.5 and 86.5 ± 1.3 km·h-1 for the right and the left side, respectively. The coefficient of variation for the velocity ranged between 1 and 2% in all stages (ball velocity ranging from 10 to 30 balls·min-1. Conclusion: both the accuracy and the reliability of this new ball machine appear satisfying enough for field testing and training.

  2. Side-View Face Recognition

    NARCIS (Netherlands)

    Santemiz, Pinar; Spreeuwers, Luuk J.; Veldhuis, Raymond N.J.; Biggelaar , van den Olivier

    2011-01-01

    As a widely used biometrics, face recognition has many advantages such as being non-intrusive, natural and passive. On the other hand, in real-life scenarios with uncontrolled environment, pose variation up to side-view positions makes face recognition a challenging work. In this paper we discuss th

  3. The DarkSide Program

    Directory of Open Access Journals (Sweden)

    Rossi B.

    2016-01-01

    Full Text Available DarkSide-50 at Gran Sasso underground laboratory (LNGS, Italy, is a direct dark matter search experiment based on a liquid argon TPC. DS-50 has completed its first dark matter run using atmospheric argon as target. The detector performances and the results of the first physics run are presented in this proceeding.

  4. The Human Side of Libraries.

    Science.gov (United States)

    Surace, Cecily J.

    This paper discusses current trends in personnel management, with emphasis on performance standards and employee evaluation. Advances in personnel management from the scientific management theory to the application of the "human side of enterprise" approach should be reflected in how library managers review personnel and operate their libraries.…

  5. 77 FR 36250 - Information Collection Request; Request for Aerial Photography

    Science.gov (United States)

    2012-06-18

    ...; ] DEPARTMENT OF AGRICULTURE Farm Service Agency Information Collection Request; Request for Aerial Photography... FSA Aerial Photography Program. The FSA Aerial Photography Field Office (APFO) uses the information from this form to collect the customer and photography information needed to produce and ship...

  6. Production Machine Shop Employment Competencies. Part Four: The Milling Machine.

    Science.gov (United States)

    Bishart, Gus; Werner, Claire

    Competencies for production machine shop are provided for the fourth of four topic areas: the milling machine. Each competency appears in a one-page format. It is presented as a goal statement followed by one or more "indicator" statements, which are performance objectives describing an ability that, upon attainment, will establish…

  7. Standardized Curriculum for Machine Tool Operation/Machine Shop.

    Science.gov (United States)

    Mississippi State Dept. of Education, Jackson. Office of Vocational, Technical and Adult Education.

    Standardized vocational education course titles and core contents for two courses in Mississippi are provided: machine tool operation/machine shop I and II. The first course contains the following units: (1) orientation; (2) shop safety; (3) shop math; (4) measuring tools and instruments; (5) hand and bench tools; (6) blueprint reading; (7)…

  8. 76 FR 28034 - Labor-Management Relations Information Collection Requests

    Science.gov (United States)

    2011-05-13

    ... CONCILIATION SERVICE Labor-Management Relations Information Collection Requests AGENCY: Federal Mediation and... information collection requests. The information collection requests are FMCS forms: Arbitrator's Report and... Request for Arbitration Services (Agency Form R-43). These information collection requests were...

  9. Music emotion detection using hierarchical sparse kernel machines.

    Science.gov (United States)

    Chin, Yu-Hao; Lin, Chang-Hong; Siahaan, Ernestasia; Wang, Jia-Ching

    2014-01-01

    For music emotion detection, this paper presents a music emotion verification system based on hierarchical sparse kernel machines. With the proposed system, we intend to verify if a music clip possesses happiness emotion or not. There are two levels in the hierarchical sparse kernel machines. In the first level, a set of acoustical features are extracted, and principle component analysis (PCA) is implemented to reduce the dimension. The acoustical features are utilized to generate the first-level decision vector, which is a vector with each element being a significant value of an emotion. The significant values of eight main emotional classes are utilized in this paper. To calculate the significant value of an emotion, we construct its 2-class SVM with calm emotion as the global (non-target) side of the SVM. The probability distributions of the adopted acoustical features are calculated and the probability product kernel is applied in the first-level SVMs to obtain first-level decision vector feature. In the second level of the hierarchical system, we merely construct a 2-class relevance vector machine (RVM) with happiness as the target side and other emotions as the background side of the RVM. The first-level decision vector is used as the feature with conventional radial basis function kernel. The happiness verification threshold is built on the probability value. In the experimental results, the detection error tradeoff (DET) curve shows that the proposed system has a good performance on verifying if a music clip reveals happiness emotion.

  10. Machine performance assessment and enhancement for a hexapod machine

    Energy Technology Data Exchange (ETDEWEB)

    Mou, J.I. [Arizona State Univ., Tempe, AZ (United States); King, C. [Sandia National Labs., Livermore, CA (United States). Integrated Manufacturing Systems Center

    1998-03-19

    The focus of this study is to develop a sensor fused process modeling and control methodology to model, assess, and then enhance the performance of a hexapod machine for precision product realization. Deterministic modeling technique was used to derive models for machine performance assessment and enhancement. Sensor fusion methodology was adopted to identify the parameters of the derived models. Empirical models and computational algorithms were also derived and implemented to model, assess, and then enhance the machine performance. The developed sensor fusion algorithms can be implemented on a PC-based open architecture controller to receive information from various sensors, assess the status of the process, determine the proper action, and deliver the command to actuators for task execution. This will enhance a hexapod machine`s capability to produce workpieces within the imposed dimensional tolerances.

  11. Theory and practice in machining systems

    CERN Document Server

    Ito, Yoshimi

    2017-01-01

    This book describes machining technology from a wider perspective by considering it within the machining space. Machining technology is one of the metal removal activities that occur at the machining point within the machining space. The machining space consists of structural configuration entities, e.g., the main spindle, the turret head and attachments such the chuck and mandrel, and also the form-generating movement of the machine tool itself. The book describes fundamental topics, including the form-generating movement of the machine tool and the important roles of the attachments, before moving on to consider the supply of raw materials into the machining space, and the discharge of swarf from it, and then machining technology itself. Building on the latest research findings “Theory and Practice in Machining System” discusses current challenges in machining. Thus, with the inclusion of introductory and advanced topics, the book can be used as a guide and survey of machining technology for students an...

  12. Development of Mathematical Model for Lifecycle Management Process of New Type of Multirip Saw Machine

    Directory of Open Access Journals (Sweden)

    B. V. Phung

    2017-01-01

    Full Text Available The subject of research is a new type of the multirip saw machine with circular reciprocating saw blades. This machine has a number of advantages in comparison with other machines of similar purpose. The paper presents an overview of different types of saw equipment and describes basic characteristics of the machine under investigation.Using the concept of lifecycle management of the considered machine in a unified information space is necessary to improve quality and competitiveness in the current production environment. In this lifecycle all the members, namely designers, technologists, customers, etc., have a philosophy to tend to optimize the overall machine design as much as possible. However, it is not always possible to achieve. Conversely, at the boundary between the phases there are several mismatching situations, if not even conflicting inconsistencies. For example, improvement of mass characteristics can lead to poor stability and rigidity of the saw blade. Machine output improvement through increasing frequency of the machine motor rotation, on the other side, results in reducing stable ability of the saw blades and so on.In order to provide a coherent framework for the collaborative environment between the members of the life cycle, the article presents a technique to construct a mathematical model that allows combining all different members’ requirements in the unified information model. The article also gives analysis of kinematic and dynamic behavior and technological characteristics of the machine. Describes in detail all the controlled parameters, functional constraints, and quality criteria of the machine under consideration. Depending on the controlled parameters, the analytical relationships formulate functional constraints and quality criteria of the machine. The proposed algorithm allows fast and exact calculation of all the functional constraints and quality criteria of the machine for a given vector of the control

  13. Server-side Filtering and Aggregation within a Distributed Environment

    Science.gov (United States)

    Currey, J. C.; Bartle, A.

    2015-12-01

    Intercalibration, validation, and data mining use cases require more efficient access to the massive volumes of observation data distributed across multiple agency data centers. The traditional paradigm of downloading large volumes of data to a centralized server or desktop computer for analysis is no longer viable. More analysis should be performed within the host data centers using server-side functions. Many comparative analysis tasks require far less than 1% of the available observation data. The Multi-Instrument Intercalibration (MIIC) Framework provides web services to find, match, filter, and aggregate multi-instrument observation data. Matching measurements from separate spacecraft in time, location, wavelength, and viewing geometry is a difficult task especially when data are distributed across multiple agency data centers. Event prediction services identify near coincident measurements with matched viewing geometries near orbit crossings using complex orbit propagation and spherical geometry calculations. The number and duration of event opportunities depend on orbit inclinations, altitude differences, and requested viewing conditions (e.g., day/night). Event observation information is passed to remote server-side functions to retrieve matched data. Data may be gridded, spatially convolved onto instantaneous field-of-views, or spectrally resampled or convolved. Narrowband instruments are routinely compared to hyperspectal instruments such as AIRS and CRIS using relative spectral response (RSR) functions. Spectral convolution within server-side functions significantly reduces the amount of hyperspectral data needed by the client. This combination of intelligent selection and server-side processing significantly reduces network traffic and data to process on local servers. OPeNDAP is a mature networking middleware already deployed at many of the Earth science data centers. Custom OPeNDAP server-side functions that provide filtering, histogram analysis (1D

  14. Semantic Vector Machines

    CERN Document Server

    Vincent, Etter

    2011-01-01

    We first present our work in machine translation, during which we used aligned sentences to train a neural network to embed n-grams of different languages into an $d$-dimensional space, such that n-grams that are the translation of each other are close with respect to some metric. Good n-grams to n-grams translation results were achieved, but full sentences translation is still problematic. We realized that learning semantics of sentences and documents was the key for solving a lot of natural language processing problems, and thus moved to the second part of our work: sentence compression. We introduce a flexible neural network architecture for learning embeddings of words and sentences that extract their semantics, propose an efficient implementation in the Torch framework and present embedding results comparable to the ones obtained with classical neural language models, while being more powerful.

  15. Regularized maximum correntropy machine

    KAUST Repository

    Wang, Jim Jing-Yan

    2015-02-12

    In this paper we investigate the usage of regularized correntropy framework for learning of classifiers from noisy labels. The class label predictors learned by minimizing transitional loss functions are sensitive to the noisy and outlying labels of training samples, because the transitional loss functions are equally applied to all the samples. To solve this problem, we propose to learn the class label predictors by maximizing the correntropy between the predicted labels and the true labels of the training samples, under the regularized Maximum Correntropy Criteria (MCC) framework. Moreover, we regularize the predictor parameter to control the complexity of the predictor. The learning problem is formulated by an objective function considering the parameter regularization and MCC simultaneously. By optimizing the objective function alternately, we develop a novel predictor learning algorithm. The experiments on two challenging pattern classification tasks show that it significantly outperforms the machines with transitional loss functions.

  16. Machine Learning Exciton Dynamics

    CERN Document Server

    Häse, Florian; Pyzer-Knapp, Edward; Aspuru-Guzik, Alán

    2015-01-01

    Obtaining the exciton dynamics of large photosynthetic complexes by using mixed quantum mechanics/molecular mechanics (QM/MM) is computationally demanding. We propose a machine learning technique, multi-layer perceptrons, as a tool to reduce the time required to compute excited state energies. With this approach we predict time-dependent density functional theory (TDDFT) excited state energies of bacteriochlorophylls in the Fenna-Matthews-Olson (FMO) complex. Additionally we compute spectral densities and exciton populations from the predictions. Different methods to determine multi-layer perceptron training sets are introduced, leading to several initial data selections. In addition, we compute spectral densities and exciton populations. Once multi-layer perceptrons are trained, predicting excited state energies was found to be significantly faster than the corresponding QM/MM calculations. We showed that multi-layer perceptrons can successfully reproduce the energies of QM/MM calculations to a high degree o...

  17. Training Restricted Boltzmann Machines

    DEFF Research Database (Denmark)

    Fischer, Asja

    Restricted Boltzmann machines (RBMs) are probabilistic graphical models that can also be interpreted as stochastic neural networks. Training RBMs is known to be challenging. Computing the likelihood of the model parameters or its gradient is in general computationally intensive. Thus, training...... relies on sampling based approximations of the log-likelihood gradient. I will present an empirical and theoretical analysis of the bias of these approximations and show that the approximation error can lead to a distortion of the learning process. The bias decreases with increasing mixing rate...... of the applied sampling procedure and I will introduce a transition operator that leads to faster mixing. Finally, a different parametrisation of RBMs will be discussed that leads to better learning results and more robustness against changes in the data representation....

  18. Mechanics of Wood Machining

    CERN Document Server

    Csanády, Etele

    2013-01-01

    Wood is one of the most valuable materials for mankind, and since our earliest days wood materials have been widely used. Today we have modern woodworking machine and tools; however, the raw wood materials available are continuously declining. Therefore we are forced to use this precious material more economically, reducing waste wherever possible. This new textbook on the “Mechanics of Wood Machining” combines the quantitative, mathematical analysis of the mechanisms of wood processing with practical recommendations and solutions. Bringing together materials from many sources, the book contains new theoretical and experimental approaches and offers a clear and systematic overview of the theory of wood cutting, thermal loading in wood-cutting tools, dynamic behaviour of tool and work piece, optimum choice of operational parameters and energy consumption, the wear process of the tools, and the general regularities of wood surface roughness. Diagrams are provided for the quick estimation of various process ...

  19. Deep Neural Network Based Demand Side Short Term Load Forecasting

    Directory of Open Access Journals (Sweden)

    Seunghyoung Ryu

    2016-12-01

    Full Text Available In the smart grid, one of the most important research areas is load forecasting; it spans from traditional time series analyses to recent machine learning approaches and mostly focuses on forecasting aggregated electricity consumption. However, the importance of demand side energy management, including individual load forecasting, is becoming critical. In this paper, we propose deep neural network (DNN-based load forecasting models and apply them to a demand side empirical load database. DNNs are trained in two different ways: a pre-training restricted Boltzmann machine and using the rectified linear unit without pre-training. DNN forecasting models are trained by individual customer’s electricity consumption data and regional meteorological elements. To verify the performance of DNNs, forecasting results are compared with a shallow neural network (SNN, a double seasonal Holt–Winters (DSHW model and the autoregressive integrated moving average (ARIMA. The mean absolute percentage error (MAPE and relative root mean square error (RRMSE are used for verification. Our results show that DNNs exhibit accurate and robust predictions compared to other forecasting models, e.g., MAPE and RRMSE are reduced by up to 17% and 22% compared to SNN and 9% and 29% compared to DSHW.

  20. CREDITWORTHINESS OF MACHINE BUILDING ENTERPRISES

    OpenAIRE

    Freimanis, Tālis; Svarinskis, Leonārs

    2009-01-01

    The previous research showed that the Latvian machine building enterprises experienced regular liquidity problems at the end of each year. Therefore to ensure their development the constant access to bank credits is a necessity. For that reason the analysis and evaluation of machine building enterprises creditworthiness was performed.

  1. SOLVENCY OF MACHINE BUILDING ENTERPRISES

    OpenAIRE

    Freimanis, Tālis; Svarinskis, Leonārs

    2009-01-01

    Machine building as a competative exporting industry plays an important role in the Latvian national open market economy. The further development of machine building is possible under the conditions of the stable solvency. Therefore, it is crucial to perform the solvency analysis of the industry enterprises and give its evaluation.

  2. Storytelling machines for video search

    NARCIS (Netherlands)

    Habibian, A.

    2016-01-01

    We study a fundamental question for developing storytelling machines: what vocabulary is suited for machines to tell the story of a video? We start by manually specifying the vocabulary concepts and their annotations. In order to effectively handcraft the vocabulary, we empirically study what are

  3. Understanding and applying machine vision

    CERN Document Server

    Zeuch, Nello

    2000-01-01

    A discussion of applications of machine vision technology in the semiconductor, electronic, automotive, wood, food, pharmaceutical, printing, and container industries. It describes systems that enable projects to move forward swiftly and efficiently, and focuses on the nuances of the engineering and system integration of machine vision technology.

  4. Storytelling machines for video search

    NARCIS (Netherlands)

    Habibian, A.

    2016-01-01

    We study a fundamental question for developing storytelling machines: what vocabulary is suited for machines to tell the story of a video? We start by manually specifying the vocabulary concepts and their annotations. In order to effectively handcraft the vocabulary, we empirically study what are th

  5. Cleaning of Free Machining Brass

    Energy Technology Data Exchange (ETDEWEB)

    Shen, T

    2005-12-29

    We have investigated four brightening treatments proposed by two cleaning vendors for cleaning free machining brass. The experimental results showed that none of the proposed brightening treatments passed the swipe test. Thus, we maintain the recommendation of not using the brightening process in the cleaning of free machining brass for NIF application.

  6. Man and Machines: Three Criticisms.

    Science.gov (United States)

    Schneider, Edward F.

    As machines have become a more common part of daily life through the passage of time, the idea that the line separating man and machine is slowly fading has become more popular as well. This paper examines three critics of change through their most famous works. One of the most popular views of Mary Shelley's "Frankenstein" is that it is a…

  7. Anaesthesia machine: Checklist, hazards, scavenging

    Directory of Open Access Journals (Sweden)

    Umesh Goneppanavar

    2013-01-01

    Full Text Available From a simple pneumatic device of the early 20 th century, the anaesthesia machine has evolved to incorporate various mechanical, electrical and electronic components to be more appropriately called anaesthesia workstation. Modern machines have overcome many drawbacks associated with the older machines. However, addition of several mechanical, electronic and electric components has contributed to recurrence of some of the older problems such as leak or obstruction attributable to newer gadgets and development of newer problems. No single checklist can satisfactorily test the integrity and safety of all existing anaesthesia machines due to their complex nature as well as variations in design among manufacturers. Human factors have contributed to greater complications than machine faults. Therefore, better understanding of the basics of anaesthesia machine and checking each component of the machine for proper functioning prior to use is essential to minimise these hazards. Clear documentation of regular and appropriate servicing of the anaesthesia machine, its components and their satisfactory functioning following servicing and repair is also equally important. Trace anaesthetic gases polluting the theatre atmosphere can have several adverse effects on the health of theatre personnel. Therefore, safe disposal of these gases away from the workplace with efficiently functioning scavenging system is necessary. Other ways of minimising atmospheric pollution such as gas delivery equipment with negligible leaks, low flow anaesthesia, minimal leak around the airway equipment (facemask, tracheal tube, laryngeal mask airway, etc. more than 15 air changes/hour and total intravenous anaesthesia should also be considered.

  8. A multipurpose tissue bending machine.

    Science.gov (United States)

    Vesely, I; Boughner, D R

    1985-01-01

    A unique tissue bending machine was developed to test the bending properties of normal and bioprosthetic heart valve material. It can be operated in air or in a tissue bath and can measure bending torques with an accuracy in excess of 1.0 microN m. Three contrasting substances were tested to compare their stiffness and to demonstrate the machine.

  9. Self-Adjusting Teaching Machines.

    Science.gov (United States)

    Dovgyallo, A. M.

    A study was made on the synthesis of teaching machine elements to ensure the stabilization of the chi indicator of the teaching process of each student. At first, a procedure was developed for calculating the chi indicator for the case when the teaching machine predicts the magnitude of this indicator based on probabilities derived from an…

  10. The Machine Scoring of Writing

    Science.gov (United States)

    McCurry, Doug

    2010-01-01

    This article provides an introduction to the kind of computer software that is used to score student writing in some high stakes testing programs, and that is being promoted as a teaching and learning tool to schools. It sketches the state of play with machines for the scoring of writing, and describes how these machines work and what they do.…

  11. Real Analytic Machines and Degrees

    CERN Document Server

    Gärtner, Tobias; 10.4204/EPTCS.24.12

    2010-01-01

    We study and compare in two degree-theoretic ways (iterated Halting oracles analogous to Kleene's arithmetical hierarchy and the Borel hierarchy of descriptive set theory) the capabilities and limitations of three models of analytic computation: BSS machines (aka real-RAM) and strongly/weakly analytic machines as introduced by Hotz et. al. (1995).

  12. Storytelling machines for video search

    NARCIS (Netherlands)

    Habibian, A.

    2016-01-01

    We study a fundamental question for developing storytelling machines: what vocabulary is suited for machines to tell the story of a video? We start by manually specifying the vocabulary concepts and their annotations. In order to effectively handcraft the vocabulary, we empirically study what are th

  13. Anaesthesia machine: checklist, hazards, scavenging.

    Science.gov (United States)

    Goneppanavar, Umesh; Prabhu, Manjunath

    2013-09-01

    From a simple pneumatic device of the early 20(th) century, the anaesthesia machine has evolved to incorporate various mechanical, electrical and electronic components to be more appropriately called anaesthesia workstation. Modern machines have overcome many drawbacks associated with the older machines. However, addition of several mechanical, electronic and electric components has contributed to recurrence of some of the older problems such as leak or obstruction attributable to newer gadgets and development of newer problems. No single checklist can satisfactorily test the integrity and safety of all existing anaesthesia machines due to their complex nature as well as variations in design among manufacturers. Human factors have contributed to greater complications than machine faults. Therefore, better understanding of the basics of anaesthesia machine and checking each component of the machine for proper functioning prior to use is essential to minimise these hazards. Clear documentation of regular and appropriate servicing of the anaesthesia machine, its components and their satisfactory functioning following servicing and repair is also equally important. Trace anaesthetic gases polluting the theatre atmosphere can have several adverse effects on the health of theatre personnel. Therefore, safe disposal of these gases away from the workplace with efficiently functioning scavenging system is necessary. Other ways of minimising atmospheric pollution such as gas delivery equipment with negligible leaks, low flow anaesthesia, minimal leak around the airway equipment (facemask, tracheal tube, laryngeal mask airway, etc.) more than 15 air changes/hour and total intravenous anaesthesia should also be considered.

  14. Bionic machines and systems

    Energy Technology Data Exchange (ETDEWEB)

    Halme, A.; Paanajaervi, J. (eds.)

    2004-07-01

    Introduction Biological systems form a versatile and complex entirety on our planet. One evolutionary branch of primates, called humans, has created an extraordinary skill, called technology, by the aid of which it nowadays dominate life on the planet. Humans use technology for producing and harvesting food, healthcare and reproduction, increasing their capability to commute and communicate, defending their territory etc., and to develop more technology. As a result of this, humans have become much technology dependent, so that they have been forced to form a specialized class of humans, called engineers, who take care of the knowledge of technology developing it further and transferring it to later generations. Until now, technology has been relatively independent from biology, although some of its branches, e.g. biotechnology and biomedical engineering, have traditionally been in close contact with it. There exist, however, an increasing interest to expand the interface between technology and biology either by directly utilizing biological processes or materials by combining them with 'dead' technology, or by mimicking in technological solutions the biological innovations created by evolution. The latter theme is in focus of this report, which has been written as the proceeding of the post-graduate seminar 'Bionic Machines and Systems' held at HUT Automation Technology Laboratory in autumn 2003. The underlaying idea of the seminar was to analyze biological species by considering them as 'robotic machines' having various functional subsystems, such as for energy, motion and motion control, perception, navigation, mapping and localization. We were also interested about intelligent capabilities, such as learning and communication, and social structures like swarming behavior and its mechanisms. The word 'bionic machine' comes from the book which was among the initial material when starting our mission to the fascinating world

  15. Machinability of Stellite 6 hardfacing

    Science.gov (United States)

    Benghersallah, M.; Boulanouar, L.; Le Coz, G.; Devillez, A.; Dudzinski, D.

    2010-06-01

    This paper reports some experimental findings concerning the machinability at high cutting speed of nickel-base weld-deposited hardfacings for the manufacture of hot tooling. The forging work involves extreme impacts, forces, stresses and temperatures. Thus, mould dies must be extremely resistant. The aim of the project is to create a rapid prototyping process answering to forging conditions integrating a Stellite 6 hardfacing deposed PTA process. This study talks about the dry machining of the hardfacing, using a two tips machining tool and a high speed milling machine equipped by a power consumption recorder Wattpilote. The aim is to show the machinability of the hardfacing, measuring the power and the tip wear by optical microscope and white light interferometer, using different strategies and cutting conditions.

  16. Machine intelligence and signal processing

    CERN Document Server

    Vatsa, Mayank; Majumdar, Angshul; Kumar, Ajay

    2016-01-01

    This book comprises chapters on key problems in machine learning and signal processing arenas. The contents of the book are a result of a 2014 Workshop on Machine Intelligence and Signal Processing held at the Indraprastha Institute of Information Technology. Traditionally, signal processing and machine learning were considered to be separate areas of research. However in recent times the two communities are getting closer. In a very abstract fashion, signal processing is the study of operator design. The contributions of signal processing had been to device operators for restoration, compression, etc. Applied Mathematicians were more interested in operator analysis. Nowadays signal processing research is gravitating towards operator learning – instead of designing operators based on heuristics (for example wavelets), the trend is to learn these operators (for example dictionary learning). And thus, the gap between signal processing and machine learning is fast converging. The 2014 Workshop on Machine Intel...

  17. Machinability of Stellite 6 hardfacing

    Directory of Open Access Journals (Sweden)

    Dudzinski D.

    2010-06-01

    Full Text Available This paper reports some experimental findings concerning the machinability at high cutting speed of nickel-base weld-deposited hardfacings for the manufacture of hot tooling. The forging work involves extreme impacts, forces, stresses and temperatures. Thus, mould dies must be extremely resistant. The aim of the project is to create a rapid prototyping process answering to forging conditions integrating a Stellite 6 hardfacing deposed PTA process. This study talks about the dry machining of the hardfacing, using a two tips machining tool and a high speed milling machine equipped by a power consumption recorder Wattpilote. The aim is to show the machinability of the hardfacing, measuring the power and the tip wear by optical microscope and white light interferometer, using different strategies and cutting conditions.

  18. Nontraditional machining processes research advances

    CERN Document Server

    2013-01-01

    Nontraditional machining employs processes that remove material by various methods involving thermal, electrical, chemical and mechanical energy or even combinations of these. Nontraditional Machining Processes covers recent research and development in techniques and processes which focus on achieving high accuracies and good surface finishes, parts machined without burrs or residual stresses especially with materials that cannot be machined by conventional methods. With applications to the automotive, aircraft and mould and die industries, Nontraditional Machining Processes explores different aspects and processes through dedicated chapters. The seven chapters explore recent research into a range of topics including laser assisted manufacturing, abrasive water jet milling and hybrid processes. Students and researchers will find the practical examples and new processes useful for both reference and for developing further processes. Industry professionals and materials engineers will also find Nontraditional M...

  19. An art history of machines?

    Directory of Open Access Journals (Sweden)

    Daniel Bridgman

    2016-12-01

    Full Text Available A toast offered in honor of Donald Preziosi on the cusp of his seventy-fifth birthday, this essay considers a range of machine metaphors, their art historical settings, and their implications. Addressing the mythography of Daedalus and his wonder machines in relation to art history’s machinic enterprises, an ancient art-archaeology seminar Preziosi directed at UCLA (in 1988 and the book, Rethinking Art History: Meditations on a Coy Science (1989 form the focus of my thinking about Preziosi’s work. At issue across the essay is the work of recursion, when machines make machines and in so doing create a recessive subjectivity for the maker. The essay ends with the speculation that art history’s disciplinary machinery may owe its generative strength to a perpetual need for replacement parts.

  20. The Dark Side of Management

    DEFF Research Database (Denmark)

    Hanlon, Gerard; Dunne, Stephen; Johnsen, Christian Garmann

    2017-01-01

    Towards the end of 2015, the ephemera collective organised, chaired and participated within two separate Q+A panels celebrating the launch of Gerard Hanlon’s The dark side of management: A secret history of management theory. The events took place in The University of Leicester’s School...... of Management and Copenhagen Business School’s Management, Politics and Philosophy Department. Each of the events were recorded, transcribed, edited and amalgamated into the following feature....

  1. Semiactive Vibration Control for Horizontal Axis Washing Machine

    Directory of Open Access Journals (Sweden)

    Barış Can Yalçın

    2015-01-01

    Full Text Available A semiactive vibration control method is developed to cope with the dynamic stability problem of a horizontal axis washing machine. This method is based on adjusting the maximum force values produced by the semiactive suspension elements considering a washing machine’s vibration data (three axis angular position and three axis angular acceleration values in time. Before actuation signals are received by the step motors of the friction dampers, vibration data are evaluated, and then, the step motors start to narrow or expand the radius of bracelets located on the dampers. This changes the damping properties of the damper in the suspension system, and thus, the semiactive suspension system absorbs unwanted vibrations and contributes to the dynamic stability of the washing machine. To evaluate the vibration data, the angular position and angular acceleration values in three axes are defined in a function, and the maximum forces produced by semiactive suspension elements are calculated according to the gradient of this function. The relation between the dynamic stability and the walking stability is also investigated. A motion (gyroscope and accelerometer sensor is installed on the top-front panel of the washing machine because a mathematical model of a horizontal axis washing machine suggests that the walking behavior starts around this location under some assumptions, and therefore, calculating the vibrations occurring there is crucial. Semiactive damping elements are located under the left and right sides of the tub. The proposed method is tested during the spinning cycle of washing machine operation, increasing gradually from 200 rpm to 900 rpm, which produces the most challenging vibration patterns for dynamic stability. Moreover, the sound power levels produced by the washing machine are measured to evaluate the noise performance of the washing machine while the semiactive suspension system is controlled. The effectiveness of the

  2. Density Based Support Vector Machines for Classification

    Directory of Open Access Journals (Sweden)

    Zahra Nazari

    2015-04-01

    Full Text Available Support Vector Machines (SVM is the most successful algorithm for classification problems. SVM learns the decision boundary from two classes (for Binary Classification of training points. However, sometimes there are some less meaningful samples amongst training points, which are corrupted by noises or misplaced in wrong side, called outliers. These outliers are affecting on margin and classification performance, and machine should better to discard them. SVM as a popular and widely used classification algorithm is very sensitive to these outliers and lacks the ability to discard them. Many research results prove this sensitivity which is a weak point for SVM. Different approaches are proposed to reduce the effect of outliers but no method is suitable for all types of data sets. In this paper, the new method of Density Based SVM (DBSVM is introduced. Population Density is the basic concept which is used in this method for both linear and non-linear SVM to detect outliers. Experiments on artificial data sets, real high-dimensional benchmark data sets of Liver disorder and Heart disease, and data sets of new and fatigued banknotes’ acoustic signals can prove the efficiency of this method on noisy data classification and the better generalization that it can provide compared to the standard SVM.

  3. Microelectrical Discharge Machining: A Suitable Process for Machining Ceramics

    Directory of Open Access Journals (Sweden)

    Andreas Schubert

    2015-01-01

    Full Text Available Today ceramics are used in many industrial applications, for example, in the biomedical field, for high-temperature components or for cutting tools. This is attributed to their excellent mechanical and physical properties, as low density, high strength, and hardness or chemical resistance. However, these specific mechanical properties lead to problems regarding the postprocessing of ceramics. In particular, cutting processes require expensive tools which cause high manufacturing costs to machine ceramics. Consequently, there is a demand for alternative machining processes. Microelectrical discharge machining (micro-EDM is a thermal abrasion process which is based on electrical discharges between a tool and a workpiece. The advantages of micro-EDM are more and more in focus for ceramic machining. These advantages include the process of being a noncontact technology, an independency of material brittleness and hardness, a low impact on the material, and the achievable microstructures. This paper presents the current state of investigations regarding micro-EDM of ceramics. Beside the process principle of EDM, the used procedures for machining ceramics and insulating ceramics are described. Furthermore several machining examples are presented to demonstrate the possibilities of the micro-EDM process with regard to the machining of ceramics.

  4. Machining Error Control by Integrating Multivariate Statistical Process Control and Stream of Variations Methodology

    Institute of Scientific and Technical Information of China (English)

    WANG Pei; ZHANG Dinghua; LI Shan; CHEN Bing

    2012-01-01

    For aircraft manufacturing industries,the analyses and prediction of part machining error during machining process are very important to control and improve part machining quality.In order to effectively control machining error,the method of integrating multivariate statistical process control (MSPC) and stream of variations (SoV) is proposed.Firstly,machining error is modeled by multi-operation approaches for part machining process.SoV is adopted to establish the mathematic model of the relationship between the error of upstream operations and the error of downstream operations.Here error sources not only include the influence of upstream operations but also include many of other error sources.The standard model and the predicted model about SoV are built respectively by whether the operation is done or not to satisfy different requests during part machining process.Secondly,the method of one-step ahead forecast error (OSFE) is used to eliminate autocorrelativity of the sample data from the SoV model,and the T2 control chart in MSPC is built to realize machining error detection according to the data characteristics of the above error model,which can judge whether the operation is out of control or not.If it is,then feedback is sent to the operations.The error model is modified by adjusting the operation out of control,and continually it is used to monitor operations.Finally,a machining instance containing two operations demonstrates the effectiveness of the machining error control method presented in this paper.

  5. Metabolic Side Effects of Lithium

    Directory of Open Access Journals (Sweden)

    M. Cagdas Eker

    2010-04-01

    Full Text Available Lithium is an alkaline ion being used since 19th century. After its widespread use in psychiatric disorders, observed side effects caused skepticism about its therapeutic efficacy. Despite several disadvantages, lithium is one of the indispensible drugs used in affective disorders, especially in bipolar disorder. It became a necessity for physicians to recognize its side effects since lithium is still accepted as a gold standard in the treatment of bipolar disorder. Adverse effects of chronic administration of lithium on several organ systems are widely known. In this article metabolic effects of lithium on thyroid and parathyroid glands, body mass index and kidneys will be discussed along with their mechanisms, clinical findings, possible risk factors and treatment. One of the most common side effect of lithium is hypothyroidism. It has the same clinical and biochemical properties as primary hypothyroidism and observed as subclinical hypothyroidism in the first place. Hypothyroidism, even its subclinical form, may be associated with non-response or inadequate response and is indicated as a risk factor for development of rapid cycling bipolar disorder. Therefore, hypothyroidism should be screened no matter how severe it is and should be treated with thyroid hormone in the presence of clinical hypothyroidism. Weight gain due to lithium administration disturbs the compliance to treatment and negatively affects the course of the illness. Increased risk for diabetes, hypertension, ischemic heart disease and stroke because of weight gain constitute other centers of problem. Indeed, it is of importance to determine the risk factors before treatment, to follow up the weight, to re-organize nutritional habits and to schedule exercises. Another frequent problematic side effect of lithium treatment is renal dysfunction which clinically present as nephrogenic diabetes insipidus with the common symptoms of polyuria and polydipsia. Nephrogenic diabetes

  6. Optimal Privacy-Cost Trade-off in Demand-Side Management with Storage

    OpenAIRE

    Tan, Onur; Gündüz, Deniz; Gómez-Vilardebó, Jesús

    2015-01-01

    Demand-side energy storage management is studied from a joint privacy-energy cost optimization perspective. Assuming that the user's power demand profile as well as the electricity prices are known non-causally, the optimal energy management (EM) policy that jointly increases the privacy of the user and reduces his energy cost is characterized. The backward water-filling interpretation is provided for the optimal EM policy. While the energy cost is reduced by requesting more energy when the p...

  7. Negotiating a demand side bid: City of San Jose case study

    Energy Technology Data Exchange (ETDEWEB)

    1993-06-01

    This report emphasizes the transferability of the gathered information to other local municipal governments. The report provides: general background information on demand side bidding; advantages and disadvantages of participation; alternative and ``ideal`` scenarios for bidding; review of potential pitfalls and lessons learned; and a general framework of information based on this particular request for DSB proposals and the City of San Joe`s response experience.

  8. A new MSc course on diagnostics of electrical machines and power electronics

    DEFF Research Database (Denmark)

    Leban, Krisztina Monika; Ritchie, Ewen

    2011-01-01

    This paper presents the structure, methodology and content of a new Diagnostics course at the Department of Energy Engineering, AAU. The lectures were to suit the problem based learning teaching method practised at AAU. Teaching was oriented to support the semester projects of the participating...... students. Additionally, specific subjects requested by participants, basic diagnosis and testing methods were presented during the lectures and workshops. General engineering knowledge about electric machines, power electronics and the combination of these was presented. The laboratory method, experiments...

  9. Decomposition of forging dies for machining planning

    CERN Document Server

    Tapie, Laurent; Anselmetti, Bernard

    2009-01-01

    This paper will provide a method to decompose forging dies for machining planning in the case of high speed machining finishing operations. This method lies on a machining feature approach model presented in the following paper. The two main decomposition phases, called Basic Machining Features Extraction and Process Planning Generation, are presented. These two decomposition phases integrates machining resources models and expert machining knowledge to provide an outstanding process planning.

  10. Decomposition of forging dies for machining planning

    OpenAIRE

    Tapie, Laurent; Mawussi, Kwamiwi; Anselmetti, Bernard

    2009-01-01

    International audience; This paper will provide a method to decompose forging dies for machining planning in the case of high speed machining finishing operations. This method lies on a machining feature approach model presented in the following paper. The two main decomposition phases, called Basic Machining Features Extraction and Process Planning Generation, are presented. These two decomposition phases integrates machining resources models and expert machining knowledge to provide an outs...

  11. Flapping propulsion with side-by-side pitching foils

    Science.gov (United States)

    Huera-Huarte, Francisco

    2016-11-01

    Fish schools are one of the most common types of collective behaviour observed in nature. One of the reasons why fish swim in groups, is to reduce the cost of transport of the school. In this work we explore the propulsive performance of two foils flapping in a symmetric configuration, i.e. with an out-of-phase flapping motion. Direct thrust measurements and Particle Image Velocimetry (PIV) allowed a detailed examination of the forces and the wake generated by the system, for different kinematics (swept angles and frequencies) and shaft separations. For certain specific cases, volumetric PIV shows major differences on how the different structures in the wake of the system evolve, depending on the imposed kinematics and the side-by-side separation between the foils. Results obtained will be compared against data produced with isolated flapping foils with similar imposed kinematics, with the aim to better understand the interactions between both and the performance of the system as a whole. The author would like to acknowledge the financial support provided by the Spanish Ministerio de Economia y competitividad (MINECO) through Grant DPI2015-71645-P.

  12. HUMAN MACHINE COOPERATIVE TELEROBOTICS

    Energy Technology Data Exchange (ETDEWEB)

    William R. Hamel; Spivey Douglass; Sewoong Kim; Pamela Murray; Yang Shou; Sriram Sridharan; Ge Zhang; Scott Thayer; Rajiv V. Dubey

    2003-06-30

    described as Human Machine Cooperative Telerobotics (HMCTR). The HMCTR combines the telerobot with robotic control techniques to improve the system efficiency and reliability in teleoperation mode. In this topical report, the control strategy, configuration and experimental results of Human Machines Cooperative Telerobotics (HMCTR), which modifies and limits the commands of human operator to follow the predefined constraints in the teleoperation mode, is described. The current implementation is a laboratory-scale system that will be incorporated into an engineering-scale system at the Oak Ridge National Laboratory in the future.

  13. 78 FR 50449 - Proposed Collection, Comment Request

    Science.gov (United States)

    2013-08-19

    ... ``Telephone Point of Purchase Survey.'' A copy of the proposed information collection request (ICR) can be... request for Office of Management and Budget approval of the information collection request; they also will... of Labor Statistics Proposed Collection, Comment Request ACTION: Notice. SUMMARY: The Department of...

  14. Machine Learning for Medical Imaging.

    Science.gov (United States)

    Erickson, Bradley J; Korfiatis, Panagiotis; Akkus, Zeynettin; Kline, Timothy L

    2017-01-01

    Machine learning is a technique for recognizing patterns that can be applied to medical images. Although it is a powerful tool that can help in rendering medical diagnoses, it can be misapplied. Machine learning typically begins with the machine learning algorithm system computing the image features that are believed to be of importance in making the prediction or diagnosis of interest. The machine learning algorithm system then identifies the best combination of these image features for classifying the image or computing some metric for the given image region. There are several methods that can be used, each with different strengths and weaknesses. There are open-source versions of most of these machine learning methods that make them easy to try and apply to images. Several metrics for measuring the performance of an algorithm exist; however, one must be aware of the possible associated pitfalls that can result in misleading metrics. More recently, deep learning has started to be used; this method has the benefit that it does not require image feature identification and calculation as a first step; rather, features are identified as part of the learning process. Machine learning has been used in medical imaging and will have a greater influence in the future. Those working in medical imaging must be aware of how machine learning works. (©)RSNA, 2017.

  15. RETRACTED: Flap side edge noise modeling and prediction

    Science.gov (United States)

    Guo, Yueping

    2013-08-01

    This article has been retracted: please see Elsevier Policy on Article Withdrawal (http://www.elsevier.com/locate/withdrawalpolicy).This article has been retracted at the request of the first author because of the overlap with previously published papers. The first author takes full responsibility and sincerely apologizes for the error made.This article has been retracted at the request of the Editor-in-Chief.The article duplicates significant parts of an earlier paper by the same author, published in AIAA (Y.P. Guo, Aircraft flap side edge noise modeling and prediction. American Institute of Aeronautics and Astronautics, (2011), 10.2514/6.2011-2731). Prior to republication, conference papers should be comprehensively extended, and re-use of any data should be appropriately cited. As such this article represents a severe abuse of the scientific publishing system. The scientific community takes a very strong view on this matter and apologies are offered to readers of the journal that this was not detected during the submission process.

  16. Lighter side of adaptive optics

    CERN Document Server

    Tyson, Robert K

    2009-01-01

    Adaptive optics has been under development for well over 40 years. It is an indisputable necessity for all major ground-based astronomical telescopes and is the foundation for laser and wavefront sensor design. Lighter Side of Adaptive Optics is a nontechnical explanation of optics, the atmosphere, and the technology for ""untwinkling"" the stars. While interweaving a fictional romantic relationship as an analogy to adaptive optics, and inserting satire, humor, and philosophical rants, Tyson makes a difficult scientific topic understandable. The ""why"" and ""how"" of adaptive optics has never

  17. [The human side of business].

    Science.gov (United States)

    Gutiérrez, M

    1989-06-01

    This article condenses some psychological and social concepts that should be understood in order to undertake any type of enterprise. This is fundamental factor in dental practice. An aid is hereby presented for the dentist to understand and apply this type of insights, which are usually kept apart from a technical activity such as odontology. Success of an enterprise depends on the quality of services rendered (in a service institution) as well as on concurrence of the different factors making up the enterprise; in this respect, the human side is a vital essence of our structure.

  18. Learning with Support Vector Machines

    CERN Document Server

    Campbell, Colin

    2010-01-01

    Support Vectors Machines have become a well established tool within machine learning. They work well in practice and have now been used across a wide range of applications from recognizing hand-written digits, to face identification, text categorisation, bioinformatics, and database marketing. In this book we give an introductory overview of this subject. We start with a simple Support Vector Machine for performing binary classification before considering multi-class classification and learning in the presence of noise. We show that this framework can be extended to many other scenarios such a

  19. Gloved Human-Machine Interface

    Science.gov (United States)

    Adams, Richard (Inventor); Olowin, Aaron (Inventor); Hannaford, Blake (Inventor)

    2015-01-01

    Certain exemplary embodiments can provide a system, machine, device, manufacture, circuit, composition of matter, and/or user interface adapted for and/or resulting from, and/or a method and/or machine-readable medium comprising machine-implementable instructions for, activities that can comprise and/or relate to: tracking movement of a gloved hand of a human; interpreting a gloved finger movement of the human; and/or in response to interpreting the gloved finger movement, providing feedback to the human.

  20. Machine learning in virtual screening.

    Science.gov (United States)

    Melville, James L; Burke, Edmund K; Hirst, Jonathan D

    2009-05-01

    In this review, we highlight recent applications of machine learning to virtual screening, focusing on the use of supervised techniques to train statistical learning algorithms to prioritize databases of molecules as active against a particular protein target. Both ligand-based similarity searching and structure-based docking have benefited from machine learning algorithms, including naïve Bayesian classifiers, support vector machines, neural networks, and decision trees, as well as more traditional regression techniques. Effective application of these methodologies requires an appreciation of data preparation, validation, optimization, and search methodologies, and we also survey developments in these areas.

  1. LHCb Computing Resources: 2019 requests and reassessment of 2018 requests

    CERN Document Server

    Bozzi, Concezio

    2017-01-01

    This document presents the computing resources needed by LHCb in 2019 and a reassessment of the 2018 requests, as resulting from the current experience of Run2 data taking and minor changes in the LHCb computing model parameters.

  2. Fundamentals of Machine Learning for Neural Machine Translation

    OpenAIRE

    Kelleher, John

    2016-01-01

    This paper presents a short introduction to neural networks and how they are used for machine translation and concludes with some discussion on the current research challenges being addressed by neural machine translation (NMT) research. The primary goal of this paper is to give a no-tears introduction to NMT to readers that do not have a computer science or mathematical background. The secondary goal is to provide the reader with a deep enough understanding of NMT that they can appreciate th...

  3. Demand Side Bidding. Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Spahn, Andrew

    2003-12-31

    This document sets forth the final report for a financial assistance award for the National Association of Regulatory Utility Commissioners (NARUC) to enhance coordination between the building operators and power system operators in terms of demand-side responses to Location Based Marginal Pricing (LBMP). Potential benefits of this project include improved power system reliability, enhanced environmental quality, mitigation of high locational prices within congested areas, and the reduction of market barriers for demand-side market participants. NARUC, led by its Committee on Energy Resources and the Environment (ERE), actively works to promote the development and use of energy efficiency and clean distributive energy policies within the framework of a dynamic regulatory environment. Electric industry restructuring, energy shortages in California, and energy market transformation intensifies the need for reliable information and strategies regarding electric reliability policy and practice. NARUC promotes clean distributive generation and increased energy efficiency in the context of the energy sector restructuring process. NARUC, through ERE's Subcommittee on Energy Efficiency, strives to improve energy efficiency by creating working markets. Market transformation seeks opportunities where small amounts of investment can create sustainable markets for more efficient products, services, and design practices.

  4. 78 FR 63181 - Information Collection Request Submitted to OMB for Review and Approval; Comment Request...

    Science.gov (United States)

    2013-10-23

    ... AGENCY Information Collection Request Submitted to OMB for Review and Approval; Comment Request; Information Requirements for Boilers and Industrial Furnaces (Renewal) AGENCY: Environmental Protection Agency... collection request (ICR), ``Information Requirements for Boilers and Industrial Furnaces (Renewal)'' (EPA ICR...

  5. 78 FR 57630 - Information Collection Request Submitted to OMB for Review and Approval; Comment Request...

    Science.gov (United States)

    2013-09-19

    ... AGENCY Information Collection Request Submitted to OMB for Review and Approval; Comment Request; Information Requirements for Importation of Nonconforming Vehicles (Renewal) AGENCY: Environmental Protection... collection request (ICR), Information Requirements for Importation of Nonconforming Vehicles (EPA ICR No.0010...

  6. 78 FR 15010 - Proposed Information Collection Request; Comment Request: Information Requirements for...

    Science.gov (United States)

    2013-03-08

    ... AGENCY Proposed Information Collection Request; Comment Request: Information Requirements for Importation... to submit three information collection requests (ICRs), ``Information Requirements for Importation of... aspects of the proposed information collections as described below. These are proposed extensions of the...

  7. 78 FR 13053 - Information Collection Request Submitted to OMB for Review and Approval; Comment Request...

    Science.gov (United States)

    2013-02-26

    ... AGENCY Information Collection Request Submitted to OMB for Review and Approval; Comment Request; Information Requirements for Locomotives and Locomotive Engines (Renewal) AGENCY: Environmental Protection... collection request (ICR), ``Information Requirements for Locomotives and Locomotive Engines (Renewal)'' (EPA...

  8. 78 FR 36776 - Proposed Information Collection Request; Comment Request; Emission Control System Performance...

    Science.gov (United States)

    2013-06-19

    ... AGENCY Proposed Information Collection Request; Comment Request; Emission Control System Performance... an information collection request (ICR), ``Emission Control System Performance Warranty Regulations and Voluntary Aftermarket Part Certification Program (Renewal)'' (EPA ICR No. 0116.10, OMB Control...

  9. 78 FR 41926 - Proposed Information Collection Request; Comment Request; Performance Evaluation Studies on...

    Science.gov (United States)

    2013-07-12

    ... AGENCY Proposed Information Collection Request; Comment Request; Performance Evaluation Studies on... an information collection request (ICR), ``Performance Evaluation Studies on Wastewater Laboratories...: (i) Evaluate whether the proposed collection of information is necessary for the proper...

  10. Machine Learning examples on Invenio

    CERN Document Server

    CERN. Geneva

    2017-01-01

    This talk will present the different Machine Learning tools that the INSPIRE is developing and integrating in order to automatize as much as possible content selection and curation in a subject based repository.

  11. ENERGY STAR Certified Vending Machines

    Data.gov (United States)

    U.S. Environmental Protection Agency — Certified models meet all ENERGY STAR requirements as listed in the Version 3.0 ENERGY STAR Program Requirements for Refrigerated Beverage Vending Machines that are...

  12. Particle accelerator; the Universe machine

    CERN Multimedia

    Yurkewicz, Katie

    2008-01-01

    "In summer 2008, scientists will switch on one of the largest machines in the world to search for the smallest of particle. CERN's Large Hadron Collider particle accelerator has the potential to chagne our understanding of the Universe."

  13. Quantum-Enhanced Machine Learning.

    Science.gov (United States)

    Dunjko, Vedran; Taylor, Jacob M; Briegel, Hans J

    2016-09-23

    The emerging field of quantum machine learning has the potential to substantially aid in the problems and scope of artificial intelligence. This is only enhanced by recent successes in the field of classical machine learning. In this work we propose an approach for the systematic treatment of machine learning, from the perspective of quantum information. Our approach is general and covers all three main branches of machine learning: supervised, unsupervised, and reinforcement learning. While quantum improvements in supervised and unsupervised learning have been reported, reinforcement learning has received much less attention. Within our approach, we tackle the problem of quantum enhancements in reinforcement learning as well, and propose a systematic scheme for providing improvements. As an example, we show that quadratic improvements in learning efficiency, and exponential improvements in performance over limited time periods, can be obtained for a broad class of learning problems.

  14. Quantum-Enhanced Machine Learning

    Science.gov (United States)

    Dunjko, Vedran; Taylor, Jacob M.; Briegel, Hans J.

    2016-09-01

    The emerging field of quantum machine learning has the potential to substantially aid in the problems and scope of artificial intelligence. This is only enhanced by recent successes in the field of classical machine learning. In this work we propose an approach for the systematic treatment of machine learning, from the perspective of quantum information. Our approach is general and covers all three main branches of machine learning: supervised, unsupervised, and reinforcement learning. While quantum improvements in supervised and unsupervised learning have been reported, reinforcement learning has received much less attention. Within our approach, we tackle the problem of quantum enhancements in reinforcement learning as well, and propose a systematic scheme for providing improvements. As an example, we show that quadratic improvements in learning efficiency, and exponential improvements in performance over limited time periods, can be obtained for a broad class of learning problems.

  15. Diamond turning machine controller implementation

    Energy Technology Data Exchange (ETDEWEB)

    Garrard, K.P.; Taylor, L.W.; Knight, B.F.; Fornaro, R.J.

    1988-12-01

    The standard controller for a Pnuemo ASG 2500 Diamond Turning Machine, an Allen Bradley 8200, has been replaced with a custom high-performance design. This controller consists of four major components. Axis position feedback information is provided by a Zygo Axiom 2/20 laser interferometer with 0.1 micro-inch resolution. Hardware interface logic couples the computers digital and analog I/O channels to the diamond turning machine`s analog motor controllers, the laser interferometer, and other machine status and control information. It also provides front panel switches for operator override of the computer controller and implement the emergency stop sequence. The remaining two components, the control computer hardware and software, are discussed in detail below.

  16. The efficiency of combined machinings

    OpenAIRE

    2012-01-01

    This paper analyses the efficiency of the finish process applied in machining of hard surfaces, completed by grinding, hard turning and also by the combination of these two procedures, on the basis of time consumption.

  17. Machine learning for healthcare technologies

    CERN Document Server

    Clifton, David A

    2016-01-01

    This book brings together chapters on the state-of-the-art in machine learning (ML) as it applies to the development of patient-centred technologies, with a special emphasis on 'big data' and mobile data.

  18. 4th Machining Innovations Conference

    CERN Document Server

    2014-01-01

    This contributed volume contains the research results presented at the 4th Machining Innovations Conference, Hannover, September 2013. The topic of the conference are new production technologies in aerospace industry and the focus is on energy efficient machine tools as well as sustainable process planning. The target audience primarily comprises researchers and experts in the field but the book may also be beneficial for graduate students.

  19. Function Concepts for Machine Parts

    DEFF Research Database (Denmark)

    Mortensen, Niels Henrik

    1999-01-01

    The majority of resources, like time and costs, consumed in industrial product development can be related to detailed design, i.e. the materialisation of machine parts (German Maschinenteile). Existing design theories based on a systems approach, e.g. Haberfellner [5] all have function, i...... to be identification of a purposeful behaviour concept, i.e. function for a machine part. The contribution is based on the theory of technical systems, Hubka and the domain theory, Andreasen....

  20. Constructing a modern city machine

    DEFF Research Database (Denmark)

    Lindegaard, Hanne; Jørgensen, Ulrik

    1998-01-01

    Based on the Copenhagen sewers debates and constructions the role of changing perceptions of water, hygiene and environment is discussed in relation to the modernisation of cities by machinating flows and infrastructures.......Based on the Copenhagen sewers debates and constructions the role of changing perceptions of water, hygiene and environment is discussed in relation to the modernisation of cities by machinating flows and infrastructures....

  1. Biosleeve Human-Machine Interface

    Science.gov (United States)

    Assad, Christopher (Inventor)

    2016-01-01

    Systems and methods for sensing human muscle action and gestures in order to control machines or robotic devices are disclosed. One exemplary system employs a tight fitting sleeve worn on a user arm and including a plurality of electromyography (EMG) sensors and at least one inertial measurement unit (IMU). Power, signal processing, and communications electronics may be built into the sleeve and control data may be transmitted wirelessly to the controlled machine or robotic device.

  2. Submission of Telecommunications Service Requests

    Science.gov (United States)

    1992-07-23

    PTTs normally require formal routing investigation be initiated for high speed data/ digital services , as well as for those occasions when a large number...4-22 DISAC 310-130-1 TABLE 14. LEADTIMES FOR EUROPEAN SERVICE (CON.) NALLA/PTT’s normally require formal RI be initiated for high speed data/ digital ... services , as well as for those occasions when a large number of circuits are requested to the same location, or circuits are requested to a new

  3. The Complexity of Abstract Machines

    Directory of Open Access Journals (Sweden)

    Beniamino Accattoli

    2017-01-01

    Full Text Available The lambda-calculus is a peculiar computational model whose definition does not come with a notion of machine. Unsurprisingly, implementations of the lambda-calculus have been studied for decades. Abstract machines are implementations schema for fixed evaluation strategies that are a compromise between theory and practice: they are concrete enough to provide a notion of machine and abstract enough to avoid the many intricacies of actual implementations. There is an extensive literature about abstract machines for the lambda-calculus, and yet—quite mysteriously—the efficiency of these machines with respect to the strategy that they implement has almost never been studied. This paper provides an unusual introduction to abstract machines, based on the complexity of their overhead with respect to the length of the implemented strategies. It is conceived to be a tutorial, focusing on the case study of implementing the weak head (call-by-name strategy, and yet it is an original re-elaboration of known results. Moreover, some of the observation contained here never appeared in print before.

  4. Shortest Paths With Side Sensors

    CERN Document Server

    Salaris, Paolo; Bicchi, Antonio

    2011-01-01

    We present a complete characterization of shortest paths to a goal position for a vehicle with unicycle kinematics and a limited range sensor, constantly keeping a given landmark in sight. Previous work on this subject studied the optimal paths in case of a frontal, symmetrically limited Field--Of--View (FOV). In this paper we provide a generalization to the case of arbitrary FOVs, including the case that the direction of motion is not an axis of symmetry for the FOV, and even that it is not contained in the FOV. The provided solution is of particular relevance to applications using side-scanning, such as e.g. in underwater sonar-based surveying and navigation.

  5. The dark side of technology

    CERN Document Server

    Townsend, Peter

    2016-01-01

    Technological progress comes with a dark side where good ideas and intentions produce undesirable results (extreme downsides include atomic and biological weapons). The many and various unexpected outcomes of technology span humorous to bizarre, to situations that threaten human survival. Development can be positive for some, but negative and isolating for others (e.g. older or poorer people). Progress is often transient, as faster electronics and computers dramatically shorten retention time of data, knowledge, and information loss (e.g. even photos may be unreadable within a generation). Progress and globalization are also destroying past languages and cultures. Advances cut across all areas of science and life, and the scope is vast from biology, medicine, agriculture, transport, electronics, computers, long-range communications, to a global economy. Reliance on technology causes unexpected technology-driven vulnerability to natural events (e.g. intense sunspot activity) that could annihilate advanced soci...

  6. Enter the DarkSide

    Science.gov (United States)

    Davini, Stefano

    2014-04-01

    A wide range of astrophysical measurements evidence that the stars and gas in all galaxies are immersed in a much larger cloud of non-luminous and non-baryonic dark matter. The nature of the dark matter is still totally unknown, and the resolution of the dark matter puzzle is of fundamental importance to cosmology, astrophysics, and elementary particle physics. One of the major lines of researches directing their efforts at detection of dark matter is direct searches of Weakly Interacting Massive Particles (WIMPs) with detectors operated in deep underground laboratories. The new generation of direct searches of WIMPs promises to probe the most interesting region of parameters for the dark matter candidates. I will review and describe the DarkSide-50 underground Argon detector at Laboratori Nazionali del Gran Sasso.

  7. Machine function based control code algebras

    NARCIS (Netherlands)

    Bergstra, J.A.

    2008-01-01

    Machine functions have been introduced by Earley and Sturgis in [6] in order to provide a mathematical foundation of the use of the T-diagrams proposed by Bratman in [5]. Machine functions describe the operation of a machine at a very abstract level. A theory of hardware and software based on machin

  8. Machining dynamics fundamentals, applications and practices

    CERN Document Server

    Cheng, Kai

    2008-01-01

    Machining dynamics are vital to the performance of machine tools and machining processes in manufacturing. This book discusses the state-of-the-art applications, practices and research in machining dynamics. It presents basic theory, analysis and control methodology. It is useful for manufacturing engineers, supervisors, engineers and designers.

  9. Singer CNC sewing and embroidery machine

    Directory of Open Access Journals (Sweden)

    Lokodi Zsolt

    2011-12-01

    Full Text Available This paper presents the adaptation of a classic foot pedal operated Singer sewing machine to a computerized numerical control (CNC sewing and embroidery machine. This machine is composed of a Singer sewing machine and a two-degrees-of-freedom XY stage designed specifically for this application. The whole system is controlled from a PC using adequate CNC control software.

  10. Process parameters effect on material removal mechanism and cut quality of abrasive water jet machining

    Directory of Open Access Journals (Sweden)

    Janković P.

    2013-01-01

    Full Text Available The process of the abrasive water jet cutting of materials, supported by the theories of fluid mechanics, abrasive wear and damage mechanics, is a high-tech technologies that provides unique capabilities compared to conventional machining processes. This paper, along the theoretical derivations, provides original contributions in the form of mathematical models of the quantity of the cut surface damage, expressed by the values of cut surface roughness. The particular part of this paper deal with the results of the original experimental research. The research aim was connected with the demands of industry, i.e. the end user. Having in mind that the conventional machining processes are not only lagging behind in terms of quality of cut, or even some requests are not able to meet, but with the advent of composite materials were not able to machine them, because they occurred unacceptable damage (mechanical damage or delamination, fiber pull-out, burning, frayed edges.

  11. Application of TRIZ approach to machine vibration condition monitoring problems

    Science.gov (United States)

    Cempel, Czesław

    2013-12-01

    Up to now machine condition monitoring has not been seriously approached by TRIZ1TRIZ= Russian acronym for Inventive Problem Solving System, created by G. Altshuller ca 50 years ago. users, and the knowledge of TRIZ methodology has not been applied there intensively. However, there are some introductory papers of present author posted on Diagnostic Congress in Cracow (Cempel, in press [11]), and Diagnostyka Journal as well. But it seems to be further need to make such approach from different sides in order to see, if some new knowledge and technology will emerge. In doing this we need at first to define the ideal final result (IFR) of our innovation problem. As a next we need a set of parameters to describe the problems of system condition monitoring (CM) in terms of TRIZ language and set of inventive principles possible to apply, on the way to IFR. This means we should present the machine CM problem by means of contradiction and contradiction matrix. When specifying the problem parameters and inventive principles, one should use analogy and metaphorical thinking, which by definition is not exact but fuzzy, and leads sometimes to unexpected results and outcomes. The paper undertakes this important problem again and brings some new insight into system and machine CM problems. This may mean for example the minimal dimensionality of TRIZ engineering parameter set for the description of machine CM problems, and the set of most useful inventive principles applied to given engineering parameter and contradictions of TRIZ.

  12. Compiling scheme using abstract state machines

    OpenAIRE

    2003-01-01

    The project investigates the use of Abstract State Machine in the process of computer program compilation. Compilation is to produce machine-code from a source program written in a high-level language. A compiler is a program written for the purpose. Machine-code is the computer-readable representation of sequences of computer instructions. An Abstract State Machine (ASM) is a notional computing machine, developed by Yuri Gurevich, for accurately and easily representing the semantics of...

  13. 49 CFR 238.217 - Side structure.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Side structure. 238.217 Section 238.217 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION... Equipment § 238.217 Side structure. Each passenger car shall comply with the following: (a) Side posts...

  14. Digital Signature Based Fax Machine Using ARM9 and Linux

    Directory of Open Access Journals (Sweden)

    Ch. Komali

    2013-01-01

    Full Text Available In this method we are having the S3C2240A (ARM9 Board which is ported with Linux in it. And this ARM9 board with Linux will be connected to the Touch Screen device. This ARM9 board intern will be connected to the LAN network (Ethernet. To design this fax machine we are using two Arm controller boards. One Arm board will keep at fax Transmission side and another board will keep at fax receiving side. By using the Ethernet we will send and receive the fax, for that we are using TCP/IP server and TCP/IP client. In this fax machine we have too many options on touch screen of arm like retrieve, sign, send, save etc. By selecting the retrieve option we can see the received text data on touch screen. If we want to transmit text data, we can select send option, then the fax will sent to the destination. On the receiving side, the received fax will be displayed on LCD touch screen. If necessary, we can sign directly on the touch panel by selecting the sign option. If we want to retransmit that signed document, we should active server. In this way bidirectional transmission and reception is possible

  15. Sensitivity of Double-Sided Split Ring Resonator Arrays to Fabrication Tolerances

    CERN Document Server

    Trang, Frank; Rogalla, Horst; Popovic, Zoya

    2012-01-01

    We present a study of the effects of fabrication tolerances on the performance of a planar array of double-sided split-ring resonators, printed on two sides of a dielectric substrate and fabricated using a printed circuit board (PCB) milling machine. The array is simulated and measured in an X-band waveguide, and the measured resonant frequency is found to be 6.3% higher than the predicted one. The sensitivity of the frequency response to several possible fabrication and measurement errors is investigated, and the dominant effect identified and demonstrated experimentally and in simulation.

  16. Transforming Biology Assessment with Machine Learning: Automated Scoring of Written Evolutionary Explanations

    Science.gov (United States)

    Nehm, Ross H.; Ha, Minsu; Mayfield, Elijah

    2012-01-01

    This study explored the use of machine learning to automatically evaluate the accuracy of students' written explanations of evolutionary change. Performance of the Summarization Integrated Development Environment (SIDE) program was compared to human expert scoring using a corpus of 2,260 evolutionary explanations written by 565 undergraduate…

  17. Transforming Biology Assessment with Machine Learning: Automated Scoring of Written Evolutionary Explanations

    Science.gov (United States)

    Nehm, Ross H.; Ha, Minsu; Mayfield, Elijah

    2012-01-01

    This study explored the use of machine learning to automatically evaluate the accuracy of students' written explanations of evolutionary change. Performance of the Summarization Integrated Development Environment (SIDE) program was compared to human expert scoring using a corpus of 2,260 evolutionary explanations written by 565 undergraduate…

  18. Automated Computer Access Request System

    Science.gov (United States)

    Snook, Bryan E.

    2010-01-01

    The Automated Computer Access Request (AutoCAR) system is a Web-based account provisioning application that replaces the time-consuming paper-based computer-access request process at Johnson Space Center (JSC). Auto- CAR combines rules-based and role-based functionality in one application to provide a centralized system that is easily and widely accessible. The system features a work-flow engine that facilitates request routing, a user registration directory containing contact information and user metadata, an access request submission and tracking process, and a system administrator account management component. This provides full, end-to-end disposition approval chain accountability from the moment a request is submitted. By blending both rules-based and rolebased functionality, AutoCAR has the flexibility to route requests based on a user s nationality, JSC affiliation status, and other export-control requirements, while ensuring a user s request is addressed by either a primary or backup approver. All user accounts that are tracked in AutoCAR are recorded and mapped to the native operating system schema on the target platform where user accounts reside. This allows for future extensibility for supporting creation, deletion, and account management directly on the target platforms by way of AutoCAR. The system s directory-based lookup and day-today change analysis of directory information determines personnel moves, deletions, and additions, and automatically notifies a user via e-mail to revalidate his/her account access as a result of such changes. AutoCAR is a Microsoft classic active server page (ASP) application hosted on a Microsoft Internet Information Server (IIS).

  19. MATERIAL PROCESSING FOR SELF-ASSEMBLING MACHINE SYSTEMS

    Energy Technology Data Exchange (ETDEWEB)

    K. LACKNER; D. BUTT; C. WENDT

    1999-06-01

    We are developing an important aspect of a new technology based on self-reproducing machine systems. Such systems could overcome resource limitations and control the deleterious side effects of human activities on the environment. Machine systems capable of building themselves promise an increase in industrial productivity as dramatic as that of the industrial revolution. To operate successfully, such systems must procure necessary raw materials from their surroundings. Therefore, next to automation, most critical for this new technology is the ability to extract important chemicals from readily available soils. In contrast to conventional metallurgical practice, these extraction processes cannot make substantial use of rare elements. We have designed a thermodynamically viable process and experimentally demonstrated most steps that differ from common practice. To this end we had to develop a small, disposable vacuum furnace system. Our work points to a viable extraction process.

  20. 12 CFR 978.4 - Form of request.

    Science.gov (United States)

    2010-01-01

    ... REQUESTS FOR INFORMATION § 978.4 Form of request. A request by a Bank to a financial regulatory agency for... and the financial regulatory agency. The request shall reference section 22 of the Act (12 U.S.C....

  1. Game-powered machine learning.

    Science.gov (United States)

    Barrington, Luke; Turnbull, Douglas; Lanckriet, Gert

    2012-04-24

    Searching for relevant content in a massive amount of multimedia information is facilitated by accurately annotating each image, video, or song with a large number of relevant semantic keywords, or tags. We introduce game-powered machine learning, an integrated approach to annotating multimedia content that combines the effectiveness of human computation, through online games, with the scalability of machine learning. We investigate this framework for labeling music. First, a socially-oriented music annotation game called Herd It collects reliable music annotations based on the "wisdom of the crowds." Second, these annotated examples are used to train a supervised machine learning system. Third, the machine learning system actively directs the annotation games to collect new data that will most benefit future model iterations. Once trained, the system can automatically annotate a corpus of music much larger than what could be labeled using human computation alone. Automatically annotated songs can be retrieved based on their semantic relevance to text-based queries (e.g., "funky jazz with saxophone," "spooky electronica," etc.). Based on the results presented in this paper, we find that actively coupling annotation games with machine learning provides a reliable and scalable approach to making searchable massive amounts of multimedia data.

  2. Mechanical design of walking machines.

    Science.gov (United States)

    Arikawa, Keisuke; Hirose, Shigeo

    2007-01-15

    The performance of existing actuators, such as electric motors, is very limited, be it power-weight ratio or energy efficiency. In this paper, we discuss the method to design a practical walking machine under this severe constraint with focus on two concepts, the gravitationally decoupled actuation (GDA) and the coupled drive. The GDA decouples the driving system against the gravitational field to suppress generation of negative power and improve energy efficiency. On the other hand, the coupled drive couples the driving system to distribute the output power equally among actuators and maximize the utilization of installed actuator power. First, we depict the GDA and coupled drive in detail. Then, we present actual machines, TITAN-III and VIII, quadruped walking machines designed on the basis of the GDA, and NINJA-I and II, quadruped wall walking machines designed on the basis of the coupled drive. Finally, we discuss walking machines that travel on three-dimensional terrain (3D terrain), which includes the ground, walls and ceiling. Then, we demonstrate with computer simulation that we can selectively leverage GDA and coupled drive by walking posture control.

  3. Reusable State Machine Code Generator

    Science.gov (United States)

    Hoffstadt, A. A.; Reyes, C.; Sommer, H.; Andolfato, L.

    2010-12-01

    The State Machine model is frequently used to represent the behaviour of a system, allowing one to express and execute this behaviour in a deterministic way. A graphical representation such as a UML State Chart diagram tames the complexity of the system, thus facilitating changes to the model and communication between developers and domain experts. We present a reusable state machine code generator, developed by the Universidad Técnica Federico Santa María and the European Southern Observatory. The generator itself is based on the open source project architecture, and uses UML State Chart models as input. This allows for a modular design and a clean separation between generator and generated code. The generated state machine code has well-defined interfaces that are independent of the implementation artefacts such as the middle-ware. This allows using the generator in the substantially different observatory software of the Atacama Large Millimeter Array and the ESO Very Large Telescope. A project-specific mapping layer for event and transition notification connects the state machine code to its environment, which can be the Common Software of these projects, or any other project. This approach even allows to automatically create tests for a generated state machine, using techniques from software testing, such as path-coverage.

  4. Machine Learning in Parliament Elections

    Directory of Open Access Journals (Sweden)

    Ahmad Esfandiari

    2012-09-01

    Full Text Available Parliament is considered as one of the most important pillars of the country governance. The parliamentary elections and prediction it, had been considered by scholars of from various field like political science long ago. Some important features are used to model the results of consultative parliament elections. These features are as follows: reputation and popularity, political orientation, tradesmen's support, clergymen's support, support from political wings and the type of supportive wing. Two parameters of reputation and popularity and the support of clergymen and religious scholars that have more impact in reducing of prediction error in election results, have been used as input parameters in implementation. In this study, the Iranian parliamentary elections, modeled and predicted using learnable machines of neural network and neuro-fuzzy. Neuro-fuzzy machine combines the ability of knowledge representation of fuzzy sets and the learning power of neural networks simultaneously. In predicting the social and political behavior, the neural network is first trained by two learning algorithms using the training data set and then this machine predict the result on test data. Next, the learning of neuro-fuzzy inference machine is performed. Then, be compared the results of two machines.

  5. Viscoelastic machine elements elastomers and lubricants in machine systems

    CERN Document Server

    MOORE, D F

    2015-01-01

    Viscoelastic Machine Elements, which encompass elastomeric elements (rubber-like components), fluidic elements (lubricating squeeze films) and their combinations, are used for absorbing vibration, reducing friction and improving energy use. Examplesinclude pneumatic tyres, oil and lip seals, compliant bearings and races, and thin films. This book sets out to show that these elements can be incorporated in machine analysis, just as in the case of conventional elements (e.g. gears, cogs, chaindrives, bearings). This is achieved by introducing elementary theory and models, by describing new an

  6. Spectrum Assignment Algorithm for Cognitive Machine-to-Machine Networks

    Directory of Open Access Journals (Sweden)

    Soheil Rostami

    2016-01-01

    Full Text Available A novel aggregation-based spectrum assignment algorithm for Cognitive Machine-To-Machine (CM2M networks is proposed. The introduced algorithm takes practical constraints including interference to the Licensed Users (LUs, co-channel interference (CCI among CM2M devices, and Maximum Aggregation Span (MAS into consideration. Simulation results show clearly that the proposed algorithm outperforms State-Of-The-Art (SOTA algorithms in terms of spectrum utilisation and network capacity. Furthermore, the convergence analysis of the proposed algorithm verifies its high convergence rate.

  7. Distributed video coding with multiple side information

    DEFF Research Database (Denmark)

    Huang, Xin; Brites, C.; Ascenso, J.

    2009-01-01

    Distributed Video Coding (DVC) is a new video coding paradigm which mainly exploits the source statistics at the decoder based on the availability of some decoder side information. The quality of the side information has a major impact on the DVC rate-distortion (RD) performance in the same way...... the quality of the predictions had a major impact in predictive video coding. In this paper, a DVC solution exploiting multiple side information is proposed; the multiple side information is generated by frame interpolation and frame extrapolation targeting to improve the side information of a single...

  8. 18 CFR 388.108 - Requests for Commission records not available through the Public Reference Room (FOIA requests).

    Science.gov (United States)

    2010-04-01

    ... “Freedom of Information Act Request.” (ii) The request must include: (A) A statement by the requester of a... be true and correct to the requester's best knowledge and belief. (3) The Director, Office of...

  9. Machine-Tractor Aggregates Operation Assurance by Mobile Maintenance Teams

    Science.gov (United States)

    Redreev, G. V.; Myalo, O. V.; Prokopov, S. P.; Solomkin, A. P.; Okunev, G. A.

    2017-07-01

    operability of machine-tractor aggregates (MTA) is ensured by purposeful activity of maintenance and repair performers. MTAs operation assurance can provide achievement of absolutely different goals. For further development of technical service formation concept concretization in the part of determining locations of maintenance and repair performers and their area of expertise is suggested, as well as of arising peculiarities of equipment. The theoretical task is reduced to the type of tasks of distribution of recourses or transportation tasks. Mobile maintenance teams of regional agricultural equipment manufacturers’ dealers have experience of technical service performance. The formed stream of requests from agricultural plants determines the direction of correcting of existing theoretical provisions, confirming necessity of further development of centralized method of technical service by efforts and means of manufacturers’ dealers.

  10. Build your own time machine

    CERN Document Server

    Clegg, Brian

    2012-01-01

    There is no physical law to prevent time travel nothing in physics to say it is impossible. So who is to say it can't be done? In Build Your Own Time Machine, acclaimed science writer Brian Clegg takes inspiration from his childhood heroes, Doctor Who and H. G. Wells, to explain the nature of time. How do we understand it and why measure it the way we do? How did the theories of one man change the way time was perceived by the world? Why wouldn't H. G. Wells's time machine have worked? And what would we need to do to make a real one? Build Your Own Time Machine explores the amazing possib

  11. Emerging Paradigms in Machine Learning

    CERN Document Server

    Jain, Lakhmi; Howlett, Robert

    2013-01-01

    This  book presents fundamental topics and algorithms that form the core of machine learning (ML) research, as well as emerging paradigms in intelligent system design. The  multidisciplinary nature of machine learning makes it a very fascinating and popular area for research.  The book is aiming at students, practitioners and researchers and captures the diversity and richness of the field of machine learning and intelligent systems.  Several chapters are devoted to computational learning models such as granular computing, rough sets and fuzzy sets An account of applications of well-known learning methods in biometrics, computational stylistics, multi-agent systems, spam classification including an extremely well-written survey on Bayesian networks shed light on the strengths and weaknesses of the methods. Practical studies yielding insight into challenging problems such as learning from incomplete and imbalanced data, pattern recognition of stochastic episodic events and on-line mining of non-stationary ...

  12. INVESTIGATION OF MAGNESIUM ALLOYS MACHINABILITY

    Directory of Open Access Journals (Sweden)

    Berat Barıs BULDUM

    2013-01-01

    Full Text Available Magnesium is the lightest structural metal. Magnesium alloys have a hexagonal lattice structure, which affects the fundamental properties of these alloys. Plastic deformation of the hexagonal lattice is more complicated than in cubic latticed metals like aluminum, copper and steel. Magnesium alloy developments have traditionally been driven by industry requirements for lightweight materials to operate under increasingly demanding conditions. Magnesium alloys have always been attractive to designers due to their low density, only two thirds that of aluminium and its alloys [1]. The element and its alloys take a big part of modern industry needs. Especially nowadays magnesium alloys are used in automotive and mechanical (trains and wagons manufacture, because of its lightness and other features. Magnesium and magnesium alloys are the easiest of all metals to machine, allowing machining operations at extremely high speed. All standard machining operations such as turning, drilling, milling, are commonly performed on magnesium parts.

  13. Higgs Machine Learning Challenge 2014

    CERN Multimedia

    Olivier, A-P; Bourdarios, C ; LAL / Orsay; Goldfarb, S ; University of Michigan

    2014-01-01

    High Energy Physics (HEP) has been using Machine Learning (ML) techniques such as boosted decision trees (paper) and neural nets since the 90s. These techniques are now routinely used for difficult tasks such as the Higgs boson search. Nevertheless, formal connections between the two research fields are rather scarce, with some exceptions such as the AppStat group at LAL, founded in 2006. In collaboration with INRIA, AppStat promotes interdisciplinary research on machine learning, computational statistics, and high-energy particle and astroparticle physics. We are now exploring new ways to improve the cross-fertilization of the two fields by setting up a data challenge, following the footsteps of, among others, the astrophysics community (dark matter and galaxy zoo challenges) and neurobiology (connectomics and decoding the human brain). The organization committee consists of ATLAS physicists and machine learning researchers. The Challenge will run from Monday 12th to September 2014.

  14. Single Bacteria as Turing Machines

    Science.gov (United States)

    Bos, Julia; Zang, Qiucen; Vyawahare, Saurabh; Austin, Robert

    2014-03-01

    In Allan Turing's famous 1950 paper on Computing Machinery and Intelligence, he started with the provocative statement: ``I propose to consider the question, `Can machines think?' This should begin with definitions of the meaning of the terms `machine' and `think'.'' In our own work on exploring the way that organisms respond to stress and evolve, it seems at times as if they come to remarkably fast solutions to problems, indicating some sort of very clever computational machinery. I'll discuss how it would appear that bacteria can indeed create a form of a Turing Machine, the first example of a computer, and how they might use this algorithm to do rapid evolution to solve a genomics problem.

  15. Plug into 'the modernizing machine'!

    DEFF Research Database (Denmark)

    Krejsler, John B.

    2013-01-01

    ‘The modernizing machine’ codes individual bodies, things and symbols with images from New Public Management, neoliberal and Knowledge Economy discourses. Drawing on Deleuze & Guattari’s concept of machines, this article explores how ‘the modernizing machine’ produces neo-liberal modernization...... of the public sector. Taking its point of departure in Danish university reform, the article explores how the university is transformed by this desiring-producing machine. ‘The modernizing machine’ wrestles with the so-called ‘democratic-Humboldtian machine’. The University Act of 2003 and the host of reforms...... bodies and minds simultaneously produce academic subjectivities by plugging into these transformative machinic forces and are produced as they are traversed by them. What is experienced as stressful closures vis-à-vis new opportunities depends to a great extent upon how these producing...

  16. Machine learning methods in chemoinformatics

    Science.gov (United States)

    Mitchell, John B O

    2014-01-01

    Machine learning algorithms are generally developed in computer science or adjacent disciplines and find their way into chemical modeling by a process of diffusion. Though particular machine learning methods are popular in chemoinformatics and quantitative structure–activity relationships (QSAR), many others exist in the technical literature. This discussion is methods-based and focused on some algorithms that chemoinformatics researchers frequently use. It makes no claim to be exhaustive. We concentrate on methods for supervised learning, predicting the unknown property values of a test set of instances, usually molecules, based on the known values for a training set. Particularly relevant approaches include Artificial Neural Networks, Random Forest, Support Vector Machine, k-Nearest Neighbors and naïve Bayes classifiers. WIREs Comput Mol Sci 2014, 4:468–481. How to cite this article: WIREs Comput Mol Sci 2014, 4:468–481. doi:10.1002/wcms.1183 PMID:25285160

  17. Vector grammars and PN machines

    Institute of Scientific and Technical Information of China (English)

    蒋昌俊

    1996-01-01

    The concept of vector grammars under the string semantic is introduced.The dass of vector grammars is given,which is similar to the dass of Chomsky grammars.The regular vector grammar is divided further.The strong and weak relation between the vector grammar and scalar grammar is discussed,so the spectrum system graph of scalar and vector grammars is made.The equivalent relation between the regular vector grammar and Petri nets (also called PN machine) is pointed.The hybrid PN machine is introduced,and its language is proved equivalent to the language of the context-free vector grammar.So the perfect relation structure between vector grammars and PN machines is formed.

  18. Machine learning phases of matter

    Science.gov (United States)

    Carrasquilla, Juan; Melko, Roger G.

    2017-02-01

    Condensed-matter physics is the study of the collective behaviour of infinitely complex assemblies of electrons, nuclei, magnetic moments, atoms or qubits. This complexity is reflected in the size of the state space, which grows exponentially with the number of particles, reminiscent of the `curse of dimensionality' commonly encountered in machine learning. Despite this curse, the machine learning community has developed techniques with remarkable abilities to recognize, classify, and characterize complex sets of data. Here, we show that modern machine learning architectures, such as fully connected and convolutional neural networks, can identify phases and phase transitions in a variety of condensed-matter Hamiltonians. Readily programmable through modern software libraries, neural networks can be trained to detect multiple types of order parameter, as well as highly non-trivial states with no conventional order, directly from raw state configurations sampled with Monte Carlo.

  19. Alpha Channeling in Mirror Machines

    Energy Technology Data Exchange (ETDEWEB)

    Fisch N.J.

    2005-10-19

    Because of their engineering simplicity, high-β, and steady-state operation, mirror machines and related open-trap machines such as gas dynamic traps, are an attractive concept for achieving controlled nuclear fusion. In these open-trap machines, the confinement occurs by means of magnetic mirroring, without the magnetic field lines closing upon themselves within the region of particle confinement. Unfortunately, these concepts have not achieved to date very spectacular laboratory results, and their reactor prospects are dimmed by the prospect of a low Q-factor, the ratio of fusion power produced to auxiliary power. Nonetheless, because of its engineering promise, over the years numerous improvements have been proposed to enhance the reactor prospects of mirror fusion, such as tandem designs, end-plugging, and electric potential barriers.

  20. Traditional machining processes research advances

    CERN Document Server

    2015-01-01

    This book collects several examples of research in machining processes. Chapter 1 provides information on polycrystalline diamond tool material and its emerging applications. Chapter 2 is dedicated to the analysis of orthogonal cutting experiments using diamond-coated tools with force and temperature measurements. Chapter 3 describes the estimation of cutting forces and tool wear using modified mechanistic models in high performance turning. Chapter 4 contains information on cutting under gas shields for industrial applications. Chapter 5 is dedicated to the machinability of magnesium and its alloys. Chapter 6 provides information on grinding science. Finally, chapter 7 is dedicated to flexible integration of shape and functional modelling of machine tool spindles in a design framework.    

  1. Machine learning for evolution strategies

    CERN Document Server

    Kramer, Oliver

    2016-01-01

    This book introduces numerous algorithmic hybridizations between both worlds that show how machine learning can improve and support evolution strategies. The set of methods comprises covariance matrix estimation, meta-modeling of fitness and constraint functions, dimensionality reduction for search and visualization of high-dimensional optimization processes, and clustering-based niching. After giving an introduction to evolution strategies and machine learning, the book builds the bridge between both worlds with an algorithmic and experimental perspective. Experiments mostly employ a (1+1)-ES and are implemented in Python using the machine learning library scikit-learn. The examples are conducted on typical benchmark problems illustrating algorithmic concepts and their experimental behavior. The book closes with a discussion of related lines of research.

  2. Aerosols generated during beryllium machining.

    Science.gov (United States)

    Martyny, J W; Hoover, M D; Mroz, M M; Ellis, K; Maier, L A; Sheff, K L; Newman, L S

    2000-01-01

    Some beryllium processes, especially machining, are associated with an increased risk of beryllium sensitization and disease. Little is known about exposure characteristics contributing to risk, such as particle size. This study examined the characteristics of beryllium machining exposures under actual working conditions. Stationary samples, using eight-stage Lovelace Multijet Cascade Impactors, were taken at the process point of operation and at the closest point that the worker would routinely approach. Paired samples were collected at the operator's breathing zone by using a Marple Personal Cascade Impactor and a 35-mm closed-faced cassette. More than 50% of the beryllium machining particles in the breathing zone were less than 10 microns in aerodynamic diameter. This small particle size may result in beryllium deposition into the deepest portion of the lung and may explain elevated rates of sensitization among beryllium machinists.

  3. Music Emotion Detection Using Hierarchical Sparse Kernel Machines

    Directory of Open Access Journals (Sweden)

    Yu-Hao Chin

    2014-01-01

    Full Text Available For music emotion detection, this paper presents a music emotion verification system based on hierarchical sparse kernel machines. With the proposed system, we intend to verify if a music clip possesses happiness emotion or not. There are two levels in the hierarchical sparse kernel machines. In the first level, a set of acoustical features are extracted, and principle component analysis (PCA is implemented to reduce the dimension. The acoustical features are utilized to generate the first-level decision vector, which is a vector with each element being a significant value of an emotion. The significant values of eight main emotional classes are utilized in this paper. To calculate the significant value of an emotion, we construct its 2-class SVM with calm emotion as the global (non-target side of the SVM. The probability distributions of the adopted acoustical features are calculated and the probability product kernel is applied in the first-level SVMs to obtain first-level decision vector feature. In the second level of the hierarchical system, we merely construct a 2-class relevance vector machine (RVM with happiness as the target side and other emotions as the background side of the RVM. The first-level decision vector is used as the feature with conventional radial basis function kernel. The happiness verification threshold is built on the probability value. In the experimental results, the detection error tradeoff (DET curve shows that the proposed system has a good performance on verifying if a music clip reveals happiness emotion.

  4. 42 CFR 102.44 - Representatives of requesters.

    Science.gov (United States)

    2010-10-01

    ... COMPENSATION PROGRAM Procedures for Filing Request Packages § 102.44 Representatives of requesters. (a) Persons other than a requester (e.g., a lawyer, guardian, friend) may file a Request Package on a requester's behalf as his or her representative. A requester need not use the services of a lawyer to secure benefits...

  5. Rotating electrical machines part 4: methods for determining synchronous machine quantities from tests

    CERN Document Server

    International Electrotechnical Commission. Geneva

    1985-01-01

    Applies to three-phase synchronous machines of 1 kVA rating and larger with rated frequency of not more than 400 Hz and not less than 15 Hz. An appendix gives unconfirmed test methods for determining synchronous machine quantities. Notes: 1 -Tests are not applicable to synchronous machines such as permanent magnet field machines, inductor type machines, etc. 2 -They also apply to brushless machines, but certain variations exist and special precautions should be taken.

  6. 15 CFR 2004.6 - Requesting records.

    Science.gov (United States)

    2010-01-01

    ... STATES TRADE REPRESENTATIVE FREEDOM OF INFORMATION POLICIES AND PROCEDURES Procedures § 2004.6 Requesting..., true and correct to the best of the requester's knowledge and belief, explaining why expedited...

  7. 77 FR 65688 - Proposed Collection; Comment Request

    Science.gov (United States)

    2012-10-30

    ... Member Assets, Core Mission Activities, Investments and Advances,'' to the Office of Management and...; Comment Request: Federal Home Loan Bank Acquired Member Assets, Core Mission Activities, Investments and... Collection; Comment Request: Federal Home Loan Bank Acquired Member Assets, Core Mission...

  8. Controls and Machine Protection Systems

    CERN Document Server

    Carrone, E

    2016-01-01

    Machine protection, as part of accelerator control systems, can be managed with a 'functional safety' approach, which takes into account product life cycle, processes, quality, industrial standards and cybersafety. This paper will discuss strategies to manage such complexity and the related risks, with particular attention to fail-safe design and safety integrity levels, software and hardware standards, testing, and verification philosophy. It will also discuss an implementation of a machine protection system at the SLAC National Accelerator Laboratory's Linac Coherent Light Source (LCLS).

  9. Magnet management in electric machines

    Energy Technology Data Exchange (ETDEWEB)

    Reddy, Patel Bhageerath; El-Refaie, Ayman Mohamed Fawzi; Huh, Kum Kang

    2017-03-21

    A magnet management method of controlling a ferrite-type permanent magnet electrical machine includes receiving and/or estimating the temperature permanent magnets; determining if that temperature is below a predetermined temperature; and if so, then: selectively heating the magnets in order to prevent demagnetization and/or derating the machine. A similar method provides for controlling magnetization level by analyzing flux or magnetization level. Controllers that employ various methods are disclosed. The present invention has been described in terms of specific embodiment(s), and it is recognized that equivalents, alternatives, and modifications, aside from those expressly stated, are possible and within the scope of the appending claims.

  10. Cooling system for rotating machine

    Science.gov (United States)

    Gerstler, William Dwight; El-Refaie, Ayman Mohamed Fawzi; Lokhandwalla, Murtuza; Alexander, James Pellegrino; Quirion, Owen Scott; Palafox, Pepe; Shen, Xiaochun; Salasoo, Lembit

    2011-08-09

    An electrical machine comprising a rotor is presented. The electrical machine includes the rotor disposed on a rotatable shaft and defining a plurality of radial protrusions extending from the shaft up to a periphery of the rotor. The radial protrusions having cavities define a fluid path. A stationary shaft is disposed concentrically within the rotatable shaft wherein an annular space is formed between the stationary and rotatable shaft. A plurality of magnetic segments is disposed on the radial protrusions and the fluid path from within the stationary shaft into the annular space and extending through the cavities within the radial protrusions.

  11. Magnet management in electric machines

    Science.gov (United States)

    Reddy, Patel Bhageerath; El-Refaie, Ayman Mohamed Fawzi; Huh, Kum Kang

    2017-03-21

    A magnet management method of controlling a ferrite-type permanent magnet electrical machine includes receiving and/or estimating the temperature permanent magnets; determining if that temperature is below a predetermined temperature; and if so, then: selectively heating the magnets in order to prevent demagnetization and/or derating the machine. A similar method provides for controlling magnetization level by analyzing flux or magnetization level. Controllers that employ various methods are disclosed. The present invention has been described in terms of specific embodiment(s), and it is recognized that equivalents, alternatives, and modifications, aside from those expressly stated, are possible and within the scope of the appending claims.

  12. Towards green lubrication in machining

    CERN Document Server

    Liew Yun Hsien, Willey

    2014-01-01

    The book gives an overview of environmental friendly gaseous and vapour, refrigerated compressed gas, solid lubricant, mist lubrication, minimum quantity lubrication (MQL) and vegetable oils that can be used as lubricants and additives in industrial machining applications. This book introduces vegetable oils as viable and good alternative resources because of their environmental friendly, non-toxic and readily biodegradable nature.  The effectiveness of various types of vegetables oils as lubricants and additives in reducing wear and friction is discussed in this book. Engineers and scientist working in the field of lubrication and machining will find this book useful.

  13. Machine-to-machine communications architectures, technology, standards, and applications

    CERN Document Server

    Misic, Vojislav B

    2014-01-01

    With the number of machine-to-machine (M2M)-enabled devices projected to reach 20 to 50 billion by 2020, there is a critical need to understand the demands imposed by such systems. Machine-to-Machine Communications: Architectures, Technology, Standards, and Applications offers rigorous treatment of the many facets of M2M communication, including its integration with current technology.Presenting the work of a different group of international experts in each chapter, the book begins by supplying an overview of M2M technology. It considers proposed standards, cutting-edge applications, architectures, and traffic modeling and includes case studies that highlight the differences between traditional and M2M communications technology.Details a practical scheme for the forward error correction code designInvestigates the effectiveness of the IEEE 802.15.4 low data rate wireless personal area network standard for use in M2M communicationsIdentifies algorithms that will ensure functionality, performance, reliability, ...

  14. Learning as a Machine: Crossovers between Humans and Machines

    Science.gov (United States)

    Hildebrandt, Mireille

    2017-01-01

    This article is a revised version of the keynote presented at LAK '16 in Edinburgh. The article investigates some of the assumptions of learning analytics, notably those related to behaviourism. Building on the work of Ivan Pavlov, Herbert Simon, and James Gibson as ways of "learning as a machine," the article then develops two levels of…

  15. Time machines and traversable wormholes in modified theories of gravity

    Directory of Open Access Journals (Sweden)

    Lobo Francisco S.N.

    2013-09-01

    Full Text Available We review recent work on wormhole geometries in the context of modified theories of gravity, in particular, in f(R gravity and with a nonminimal curvature-matter coupling, and in the recently proposed hybrid metric-Palatini theory. In principle, the normal matter threading the throat can be shown to satisfy the energy conditions and it is the higher order curvatures terms that sustain these wormhole geometries. We also briefly review the conversion of wormholes into time-machines, explore several of the time travel paradoxes and possible remedies to these intriguing side-effects in wormhole physics.

  16. PRAGMATIC TRANSFER IN REQUEST REALIZATIONS

    Directory of Open Access Journals (Sweden)

    Indawan Syahri

    2007-01-01

    Full Text Available This study investigates the pragmatic transfer in English request realizations made by EFL learners, i.e. the proficient learners. The subjects were students of an English Study Program who obtained TOEFL-like scores of at least 450. The data were collected by means of DCT-questionnaires and Role-plays. The results show that the subjects realize requests in the form of external modifications more frequently. Most of them embed their requests with supportive moves dominantly. They enfold the acts with the moves before, after or in both positions. Of the three positions, they mostly insert the moves initial position, i.e., through inductive patterns. This is due to pragmatic transfer.

  17. Side force formation mechanism and change law of TBM center cutter

    Institute of Scientific and Technical Information of China (English)

    夏毅敏; 田彦朝; 谭青; 侯禹蒙

    2016-01-01

    The center cutter of a hard rock tunnel boring machine (TBM) is installed on the cutterhead at a small radius and thus bears complex side force. Given this fact, the formation mechanism and change law of the side force suffered by the center cutter were studied. Based on the rock shear failure criterion in combination with the lateral rolling width, a model for predicting the average side force was set up. Besides, a numerical analysis model of the rock fragmentation of the center cutter was established, and the instantaneous load changing features were investigated. Results shows that the inner side of the center cutter can form lateral rolling annulus in rock during the rotary cutting process. The smaller the installation radius is, the greater the cutter side force will be. In a working condition, the side force of the innermost center cutter is 11.66 kN, while it decreases sharply when installation radius increases. Variation tends to be gentle when installation radius is larger than 500 mm, and the side force of the outermost center cutter is reduced to 0.74 kN.

  18. Car Side Structure Crashworthiness in Pole and Moving Deformable Barrier Side Impacts

    Institute of Scientific and Technical Information of China (English)

    WANG Dazhi; DONG Guang; ZHANG Jinhuan; HUANG Shilin

    2006-01-01

    To clearly understand passenger car structure's crashworthiness in typical side impacts of pole and moving deformable barrier (MDB) impact modes, which could assist the establishment of Chinese vehicle side impact safety regulations, a full midsized car finite element model, calibrated by pole side impact test, was built and the pole side impact according to European New Car Assessment Program (EuroNCAP) and the MDB side impact according to ECE R95 regulations were simulated with LS-DYNA. The accelerations and the structure deformations from simulations were compared. It can be concluded that the pole side impact focuses primarily on side structure crashworthiness as a result of large intrusions, while the MDB side impact focuses primarily on full side structure crashworthiness. Accordingly, occupant protection strategies focus on different aspects to improve side impact safety. In the pole side impact the objective is to maintain the passenger compartment and protect the passenger's head from impacting the pole, while in the MDB side impact the objective is to protect the full human body. In the design of the car side structures, at least these two tests should be considered for assessing their side impact crashworthiness. Conducting these two side impact tests as certified tests provides insights into car safety during side impacts.

  19. Online algorithms for scheduling with machine activation cost on two uniform machines

    Institute of Scientific and Technical Information of China (English)

    HAN Shu-guang; JIANG Yi-wei; HU Jue-liang

    2007-01-01

    In this paper we investigate a variant of the scheduling problem on two uniform machines with speeds 1 and s. For this problem, we are given two potential uniform machines to process a sequence of independent jobs. Machines need to be activated before starting to process, and each machine activated incurs a fixed machine activation cost. No machines are initially activated,and when a job is revealed, the algorithm has the option to activate new machines. The objective is to minimize the sum of the makespan and the machine activation cost. We design optimal online algorithms with competitive ratio of (2s+1)/(s+1) for every s≥1.

  20. Investigation of Surfaces after Non Conventional Machining

    Science.gov (United States)

    Micietova, Anna; Neslusan, Miroslav; Cillikova, Maria

    2016-12-01

    This paper deals with analysis of surface integrity of steel after electro discharge machining (EDM), water jet machining, (WJM) laser beam machining (LBM) and plasma beam machining (PBM). The paper discusses surface integrity expressed in surface roughness, sample precision expressed in perpendicularity deviation as well as stress state. This study also demonstrates influence of the various non-conventional methods on structure transformations and reports about sensitivity of the different non-conventional methods of machining with regard to variable thickness of machined samples.

  1. System Research Of Multi-Barrel Machine Guns Installed On Board Of The Helicopter Of Mi-17 Type

    Directory of Open Access Journals (Sweden)

    Bęczkowski Grzegorz

    2015-08-01

    Full Text Available This article presents tests of a multi-barreled machine gun system built on board of a helicopter. The described weapon system consists of three 7.62 mm M-134G multi-barreled machine guns built on the designed frames of shooting positions located in the escape hatch window, the side doors and the rear doors of the transport cabin of the Mi-17-1V helicopter.

  2. 75 FR 5783 - Request for Information (RFI)

    Science.gov (United States)

    2010-02-04

    ... of Energy Efficiency and Renewable Energy Request for Information (RFI) AGENCY: Office of Energy Efficiency and Renewable Energy, Department of Energy. ACTION: Request for information (RFI). SUMMARY: The... 2009, Public Law 111-5. DOE is seeking information organized into two distinct parts. Part 1 requests...

  3. 21 CFR 710.4 - Information requested.

    Science.gov (United States)

    2010-04-01

    ... VOLUNTARY REGISTRATION OF COSMETIC PRODUCT ESTABLISHMENTS § 710.4 Information requested. Form FD-2511 requests information on the name and address of the cosmetic product establishment, including post office... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Information requested. 710.4 Section 710.4 Food...

  4. 75 FR 55612 - Proposed Collection, Comment Request

    Science.gov (United States)

    2010-09-13

    ... ``Telephone Point of Purchase Survey.'' A copy of the proposed information collection request (ICR) can be.../or included in the request for Office of Management and Budget approval of the information collection... of Labor Statistics Proposed Collection, Comment Request ACTION: Notice. SUMMARY: The Department of...

  5. 32 CFR 887.4 - Requesting CILs.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 6 2010-07-01 2010-07-01 false Requesting CILs. 887.4 Section 887.4 National... CERTIFICATES IN LIEU OF LOST OR DESTROYED CERTIFICATES OF SEPARATION § 887.4 Requesting CILs. (a) Standard Form...: Persons authorized CILs may be assisted in their request by the Customer Service Unit (DPMAC) in the...

  6. 31 CFR 103.81 - Submitting requests.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 1 2010-07-01 2010-07-01 false Submitting requests. 103.81 Section 103.81 Money and Finance: Treasury Regulations Relating to Money and Finance FINANCIAL RECORDKEEPING... which the request is made. (b) A request filed by a corporation shall be signed by a corporate officer...

  7. Development and Application of Rare Earth Permanent Magnet (REPM) Material in Electric Machines

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    With the development of permanent materials, the development and application of permanent material electric machine (REPM) have been more mature. At first the state of development and application of REPM electric machine is presented in this paper, many RMEM have been produced in volume such as the pilot exciter used for power set of large-scale thermal power station, the special RMEM synchronous motor for textile, the starter motor for automobile, the brushless permanent magnet DC motor for electric facilities, permanent magnet servomotor for numerical controlled machine tool, rare-earth torque motor, special micro-motor for automobile and so on. Secondly the field of application of REPM electric machine and remaining problems is analyzed, because of the price of the rare-earth permanent magnet materials, the cost of RMEM is currently higher than that of induction machine, on the other side the dispersibility of performance of rare-earth permanent magnet materials and the limitation of technique of integral excitation are also remaining problems, above-mentioned problems handicapped the popularization of REPMEM. At last the developing prospect and trend of REPM electric machines is described, there are four promising types of PMEM: economical type, high performance type, high efficiency and energy-saving type, micromation, intelligibility type. With the appearance of new REPM material and the improvement of its performance and the continuous perfection of performance of electric-power electronic components, the development and the application of REPM electric machines will be further progressed.

  8. Machine Room Less Elevator Traction Machine Installation Shock Absorption Design%无机房电梯曳引机安装减震设计

    Institute of Scientific and Technical Information of China (English)

    黄义茂

    2014-01-01

    传统的大载重无机房电梯,曳引机侧置在井道时,由于曳引机布置问题,在搁机梁上设置防震橡胶时,防震橡胶受力不均衡,曳引机有倾覆的趋势,在不改变传统布局的情况下,设计一种减震方式,以达到曳引机安装减震的目的。%For the traditional heavy load machine room less elevator,when the traction machine is side put in the hoistway,because the machine layout problem,if set the shockproof rubber in the machine beam,shockproof rubber stress is not balanced,traction machine has the trend to overturn. Aiming at this problem,designs a shockproof mode without changing the traditional layout,in order to achieve the purpose of the traction machine shock absorption.

  9. LHCb Computing Resources: 2018 requests and preview of 2019 requests

    CERN Document Server

    Bozzi, Concezio

    2017-01-01

    This document presents a reassessment of computing resources needed by LHCb in 2018 and a preview of computing requests for 2019, as resulting from the current experience of Run2 data taking and recent changes in the LHCb computing model parameters.

  10. Coordination Control Of Complex Machines

    NARCIS (Netherlands)

    J.C.M. Baeten; B. van Beek; J. Markovski; L.J.A.M. Somers

    2015-01-01

    Control and coordination are important aspects of the development of complex machines due to an ever-increasing demand for better functionality, quality, and performance. In WP6 of the C4C project, we developed a synthesis-centric systems engineering framework suitable for supervisory coordination o

  11. Attention: A Machine Learning Perspective

    DEFF Research Database (Denmark)

    Hansen, Lars Kai

    2012-01-01

    We review a statistical machine learning model of top-down task driven attention based on the notion of ‘gist’. In this framework we consider the task to be represented as a classification problem with two sets of features — a gist of coarse grained global features and a larger set of low...

  12. Machine Learning applications in CMS

    CERN Document Server

    CERN. Geneva

    2017-01-01

    Machine Learning is used in many aspects of CMS data taking, monitoring, processing and analysis. We review a few of these use cases and the most recent developments, with an outlook to future applications in the LHC Run III and for the High-Luminosity phase.

  13. Parsing statistical machine translation output

    NARCIS (Netherlands)

    Carter, S.; Monz, C.; Vetulani, Z.

    2009-01-01

    Despite increasing research into the use of syntax during statistical machine translation, the incorporation of syntax into language models has seen limited success. We present a study of the discriminative abilities of generative syntax-based language models, over and above standard n-gram models,

  14. Man-machine interactions 3

    CERN Document Server

    Czachórski, Tadeusz; Kozielski, Stanisław

    2014-01-01

    Man-Machine Interaction is an interdisciplinary field of research that covers many aspects of science focused on a human and machine in conjunction.  Basic goal of the study is to improve and invent new ways of communication between users and computers, and many different subjects are involved to reach the long-term research objective of an intuitive, natural and multimodal way of interaction with machines.  The rapid evolution of the methods by which humans interact with computers is observed nowadays and new approaches allow using computing technologies to support people on the daily basis, making computers more usable and receptive to the user's needs.   This monograph is the third edition in the series and presents important ideas, current trends and innovations in  the man-machine interactions area.  The aim of this book is to introduce not only hardware and software interfacing concepts, but also to give insights into the related theoretical background. Reader is provided with a compilation of high...

  15. Teaching Machines to Think Fuzzy

    Science.gov (United States)

    Technology Teacher, 2004

    2004-01-01

    Fuzzy logic programs for computers make them more human. Computers can then think through messy situations and make smart decisions. It makes computers able to control things the way people do. Fuzzy logic has been used to control subway trains, elevators, washing machines, microwave ovens, and cars. Pretty much all the human has to do is push one…

  16. Macchines per scoprire - Discovery Machines

    CERN Multimedia

    Auditorium, Rome

    2016-01-01

    During the FCC week 2016 a public event entitled “Discovery Machines: The Higgs Boson and the Search for New Physics took place on 14 April at the Auditorium in Rome. The event, brought together physicists and experts from economics to discuss intriguing questions on the origin and evolution of the Universe and the societal impact of large-scale research projects.

  17. Precision Machining Technology. Curriculum Guide.

    Science.gov (United States)

    Idaho State Dept. of Education, Boise. Div. of Vocational Education.

    This curriculum guide was developed from a Technical Committee Report prepared with the assistance of industry personnel and containing a Task List which is the basis of the guide. It presents competency-based program standards for courses in precision machining technology and is part of the Idaho Vocational Curriculum Guide Project, a cooperative…

  18. The Garden and the Machine

    DEFF Research Database (Denmark)

    Clemmensen, Thomas Juel

    2014-01-01

    The aim of this paper is to explore how the concepts of garden and machine might inform our understanding of the complex relationship between infrastructure and nature. The garden is introduced as a third nature and used to shed a critical light on the promotion of landscape ‘as’ infrastructure...

  19. Automatic Evaluation of Machine Translation

    DEFF Research Database (Denmark)

    Martinez, Mercedes Garcia; Koglin, Arlene; Mesa-Lao, Bartolomé

    2015-01-01

    The availability of systems capable of producing fairly accurate translations has increased the popularity of machine translation (MT). The translation industry is steadily incorporating MT in their workflows engaging the human translator to post-edit the raw MT output in order to comply with a set...

  20. THE GARDEN AND THE MACHINE

    DEFF Research Database (Denmark)

    Clemmensen, Thomas Juel

    2012-01-01

    The aim of this paper is to explore how the concepts of garden and machine might inform our understanding of the complex relationship between infrastructure and nature. The garden is introduced as a third nature and used to shed a critical light on the promotion of landscape as infrastructure...

  1. Dimensioning, Tolerancing, and Machine Finishes.

    Science.gov (United States)

    Adams, George C.

    Intended for use with the vocational education student interested in technical drawing, this guide provides answers to questions relating to dimensioning and tolerancing machine drawings. It also gives examples of standard dimensioning practices, tolerancing applications, and finish applications. The problems and examples presented are based on…

  2. High Temperature Superconductor Machine Prototype

    DEFF Research Database (Denmark)

    Mijatovic, Nenad; Jensen, Bogi Bech; Træholt, Chresten

    2011-01-01

    A versatile testing platform for a High Temperature Superconductor (HTS) machine has been constructed. The stationary HTS field winding can carry up to 10 coils and it is operated at a temperature of 77K. The rotating armature is at room temperature. Test results and performance for the HTS field...

  3. Machine Tool Operation, Course Description.

    Science.gov (United States)

    Denny, Walter E.; Anderson, Floyd L.

    Prepared by an instructor and curriculum specialists, this course of study was designed to meet the individual needs of the dropout and/or hard-core unemployed youth by providing them skill training, related information, and supportive services knowledge in machine tool operation. The achievement level of each student is determined at entry, and…

  4. The Improved Relevance Voxel Machine

    DEFF Research Database (Denmark)

    Ganz, Melanie; Sabuncu, Mert; Van Leemput, Koen

    The concept of sparse Bayesian learning has received much attention in the machine learning literature as a means of achieving parsimonious representations of features used in regression and classification. It is an important family of algorithms for sparse signal recovery and compressed sensing...

  5. Electrical discharge machining in dentistry.

    Science.gov (United States)

    Van Roekel, N B

    1992-01-01

    A brief history of electrical discharge machining (EDM) is given and the process is discussed. A description of the application of EDM for fabricating precision attachment removable partial dentures, fixed-removable implant prostheses, and titanium-ceramic crowns is presented. The advantages and disadvantages of the EDM process for the dental profession are evaluated. Although expensive, the procedure has merit.

  6. Machinic Deconstruction : literature/ politics/ technics

    NARCIS (Netherlands)

    Ieven, Bram Koen

    2007-01-01

    Taking its cue from Jacques Derrida’s concept of différance, Machinic Deconstruction: Literature / Politics / Technics addresses the question whether it is possible to conceive of a work of technics that is operative at the same quasi-ontological level as différance itself. To do so, this study deve

  7. Molecular machines open cell membranes

    Science.gov (United States)

    García-López, Víctor; Chen, Fang; Nilewski, Lizanne G.; Duret, Guillaume; Aliyan, Amir; Kolomeisky, Anatoly B.; Robinson, Jacob T.; Wang, Gufeng; Pal, Robert; Tour, James M.

    2017-08-01

    Beyond the more common chemical delivery strategies, several physical techniques are used to open the lipid bilayers of cellular membranes. These include using electric and magnetic fields, temperature, ultrasound or light to introduce compounds into cells, to release molecular species from cells or to selectively induce programmed cell death (apoptosis) or uncontrolled cell death (necrosis). More recently, molecular motors and switches that can change their conformation in a controlled manner in response to external stimuli have been used to produce mechanical actions on tissue for biomedical applications. Here we show that molecular machines can drill through cellular bilayers using their molecular-scale actuation, specifically nanomechanical action. Upon physical adsorption of the molecular motors onto lipid bilayers and subsequent activation of the motors using ultraviolet light, holes are drilled in the cell membranes. We designed molecular motors and complementary experimental protocols that use nanomechanical action to induce the diffusion of chemical species out of synthetic vesicles, to enhance the diffusion of traceable molecular machines into and within live cells, to induce necrosis and to introduce chemical species into live cells. We also show that, by using molecular machines that bear short peptide addends, nanomechanical action can selectively target specific cell-surface recognition sites. Beyond the in vitro applications demonstrated here, we expect that molecular machines could also be used in vivo, especially as their design progresses to allow two-photon, near-infrared and radio-frequency activation.

  8. Design of Waste Shredder Machine

    Directory of Open Access Journals (Sweden)

    Asst. Prof. S.Nithyananth

    2014-03-01

    Full Text Available The conventional agro-waste disposal is a traditional and oldest method of waste disposal in which agriculture wastes are dumped as it is to degrade in a particular place for decomposing. As the wastes are dumped as such, it takes more time to degrade and it causes environmental pollution. The waste shredder machine aims to reduce the agro waste and convert it into useful nourishing fertilizer. It decreases the man work making the farm neat and clean. Also it reduces the heap amount of pollution, disease causing agro-wastes and produces a better fertilizer with vermin compost. The waste shredder machine is an attachment as like a ploughing attachment. In the shredder attachment input power and rigid support is provided by a KAMCO Tera-trac 4W tractor by means of PTO (power take off shaft and three point linkage. PTO shaft of the tractor acts as a basic power input and the three point linkage provide a rigid support to the machine. Various kinds of blades are used for chipping and powdering operations like sawing blades, rotatory blades, and triangular shape blades. The blades are mounted on the shaft. The power is transmitted to another shaft by means of pulley and belt. For designing waste shredder machine, Creo parametric 1.0 software is used.

  9. Machine Gun Liner Bond Strength

    Science.gov (United States)

    2007-08-01

    explosive bonding of pure tantalum, several tantalum alloys, and Stellite 25 (an alloy of cobalt, chrome , nickel, and tungsten) in a liner...Difficulties have been experienced in machining an explosively- clad tantalum alloy in an M242 Bushmaster barrel [6].) One disadvantage of Stellite 25 was

  10. How To Teach Common Characteristics of Machine Tools

    Science.gov (United States)

    Kazanas, H. C.

    1970-01-01

    Organizes machine tools and machine operations into commonalities in order to help the student visualize and distinguish the common characteristics which exist between machine tools and operations. (GR)

  11. Physiological and skill demands of 'on-side' and 'off-side' games.

    Science.gov (United States)

    Gabbett, Tim J; Jenkins, David G; Abernethy, Bruce

    2010-11-01

    This study investigated the physiological and skill demands of 'on-side' and 'off-side' games in elite rugby league players. Sixteen male rugby league players participated in 'on-side' and 'off-side' games. Both small-sided games were played in a 40- × 40-m playing area. The 'off-side' game permitted players to have 3 'plays' while in possession of the ball. Players were permitted to pass backward or forward (to an 'off-side' player). The 'on-side' game also permitted players to have 3 'plays' while in possession of the ball. However, players were only permitted to pass backward to players in an 'on-side' position. Heart rate and movement patterns (via global positioning system) were recorded continuously throughout both games. Data were collected on the distance covered, number of high-acceleration and velocity efforts, and recovery between efforts. Video footage was also taken to track the performance of the players. Post hoc inspection of the footage was undertaken to count the number of possessions and the number and quality of disposals. In comparison to 'on-side' games, 'off-side' games had a greater number of involvements ("touches"), passes, and effective passes. However, the cognitive demands of 'on-side' games were greater than 'off-side' games. 'Off-side' games resulted in a greater total distance covered, greater distance covered in mild and moderate accelerations, and greater distance covered in low, moderate, and high-velocity efforts. There were also a greater number of short duration recovery periods between efforts in 'off-side' games. The results of this study demonstrate that 'off-side' games provide greater physiological and skill demands than 'on-side' games. 'Off-side' games may provide a practical alternative to 'on-side' games for the development of skill and fitness in elite rugby league players.

  12. Sexual side effects induced by psychotropic drugs

    DEFF Research Database (Denmark)

    Kristensen, Ellids

    2002-01-01

    with no or very few sexual side effects have begun to emerge. The treatment of sexual side effects induced by psychotropic drugs may consist of: modified sexual habits, reduction in dosage, switching to another medication, possibly in combination with different psychotropic agents, other varieties......The majority of psychotropic drugs entail sexual side effects. The sexual side effects may reduce quality of life and may give rise to non-compliance. For example, 30-60 per cent of patients treated with antidepressants are known to develop a sexual dysfunction. However, some psychotropic drugs...

  13. Right-sided diverticulitis mimics appendicitis.

    Science.gov (United States)

    Gilmore, Thomas; Jordan, Charlton; Edelstein, Elisabeth

    2013-01-01

    Right-sided diverticulitis is a rare source of right lower quadrant pain in Western society; however, it is quite common in Asian societies. Right-sided diverticulitis presents very similarly to appendicitis, with right lower quadrant pain, fever, nausea, and laboratory abnormalities, and is often seen in young patients. In this report, we present a case of right-sided diverticulitis. We review right-sided diverticulitis' diagnosis and management. It is important to diagnose right-sided diverticulitis because it is a good mimic of appendicitis and ideally should be diagnosed before a patient has unnecessary surgery. A 26-year-old Asian woman presented for evaluation of right lower quadrant pain and fever. She was initially thought to have appendicitis clinically, but had right-sided diverticulitis diagnosed by computed tomography (CT) scan. She was admitted and received intravenous antibiotics and bowel rest. Her right-sided diverticulitis resolved in 3 days. Severe right lower quadrant pain in young patients of Asian descent can be right-sided diverticulitis. Right-sided diverticulitis is a benign condition managed medically that mimics appendicitis. CT imaging seems to be the best way to avoid unnecessary surgery. Copyright © 2013 Elsevier Inc. All rights reserved.

  14. New Typewriter Displaces "Big Name" Machines.

    Science.gov (United States)

    School Business Affairs, 1983

    1983-01-01

    The Schoolwriter is a typewriter available at nearly half the price of competing machines. Schools in Minnesota and Maryland have purchased it for classroom machines and have had substantial savings. (MD)

  15. Mastering machine learning with scikit-learn

    CERN Document Server

    Hackeling, Gavin

    2014-01-01

    If you are a software developer who wants to learn how machine learning models work and how to apply them effectively, this book is for you. Familiarity with machine learning fundamentals and Python will be helpful, but is not essential.

  16. A Concrete Framework for Environment Machines

    DEFF Research Database (Denmark)

    Biernacka, Malgorzata; Danvy, Olivier

    2007-01-01

    calculus with explicit substitutions), we extend it minimally so that it can also express one-step reduction strategies, and we methodically derive a series of environment machines from the specification of two one-step reduction strategies for the lambda-calculus: normal order and applicative order....... The derivation extends Danvy and Nielsen’s refocusing-based construction of abstract machines with two new steps: one for coalescing two successive transitions into one, and the other for unfolding a closure into a term and an environment in the resulting abstract machine. The resulting environment machines...... include both the Krivine machine and the original version of Krivine’s machine, Felleisen et al.’s CEK machine, and Leroy’s Zinc abstract machine....

  17. Machine-Aided Indexing for NASA STI.

    Science.gov (United States)

    Wilson, John

    1987-01-01

    Describes the use of machine aided indexing as part of NASA's information systems. The discussion covers reasons for incorporating machine aided indexing, the lexical dictionary used, subject switching, natural language processing, benefits to the system, and possible future developments. (CLB)

  18. Novel Switched Flux Permanent Magnet Machine Topologies

    Institute of Scientific and Technical Information of China (English)

    诸自强

    2012-01-01

    This paper overviews various switched flux permanent magnet machines and their design and performance features,with particular emphasis on machine topologies with reduced magnet usage or without using magnet,as well as with variable flux capability.

  19. Setup Aid for Electrical-Discharge Machining

    Science.gov (United States)

    Lines, G.; Duca, J.

    1985-01-01

    Interlock assures that workpiece is correctly assembled in machining fixture. A Plunger in a Hollow Shaft actuates a switch, allowing a power supply to produce current for electrical-discharge machining. Plunger operates only when necessary parts are position.

  20. Cesarean section by maternal request.

    Science.gov (United States)

    Câmara, Raphael; Burlá, Marcelo; Ferrari, José; Lima, Lana; Amim, Joffre; Braga, Antonio; Rezende, Jorge

    2016-01-01

    Cesarean section by maternal request is the one performed on a pregnant woman without medical indication and without contraindication to vaginal delivery. There is great controversy over requested cesarean section. Potential risks include complications in subsequent pregnancies, such as uterine rupture, placenta previa and accreta. Potential benefits of requested cesareans include a lower risk of postpartum hemorrhage in the first cesarean and fewer surgical complications compared with vaginal delivery. Cesarean section by request should never be performed before 39 weeks. RESUMO A cesariana a pedido materno é aquela realizada em uma gestante sem indicações médicas e sem contraindicação para tentativa do parto vaginal. Existe grande controvérsia sobre a realização da cesariana a pedido. Riscos potenciais da cesariana a pedido incluem complicações em gravidezes subsequentes, tais como: rotura uterina, placenta prévia e acretismo. Potenciais benefícios da cesariana a pedido englobam um menor risco de hemorragia pós-parto na primeira cesariana e menos complicações cirúrgicas quando comparada ao parto vaginal. A cesariana a pedido jamais deve ser realizada antes de 39 semanas.

  1. Optimized Virtual Machine Placement with Traffic-Aware Balancing in Data Center Networks

    Directory of Open Access Journals (Sweden)

    Tao Chen

    2016-01-01

    Full Text Available Virtualization has been an efficient method to fully utilize computing resources such as servers. The way of placing virtual machines (VMs among a large pool of servers greatly affects the performance of data center networks (DCNs. As network resources have become a main bottleneck of the performance of DCNs, we concentrate on VM placement with Traffic-Aware Balancing to evenly utilize the links in DCNs. In this paper, we first proposed a Virtual Machine Placement Problem with Traffic-Aware Balancing (VMPPTB and then proved it to be NP-hard and designed a Longest Processing Time Based Placement algorithm (LPTBP algorithm to solve it. To take advantage of the communication locality, we proposed Locality-Aware Virtual Machine Placement Problem with Traffic-Aware Balancing (LVMPPTB, which is a multiobjective optimization problem of simultaneously minimizing the maximum number of VM partitions of requests and minimizing the maximum bandwidth occupancy on uplinks of Top of Rack (ToR switches. We also proved it to be NP-hard and designed a heuristic algorithm (Least-Load First Based Placement algorithm, LLBP algorithm to solve it. Through extensive simulations, the proposed heuristic algorithm is proven to significantly balance the bandwidth occupancy on uplinks of ToR switches, while keeping the number of VM partitions of each request small enough.

  2. Cutting tool materials for high speed machining

    Institute of Scientific and Technical Information of China (English)

    LIU Zhanqiang; AI Xing

    2005-01-01

    High speed machining (HSM) is one of the emerging cutting processes, which is machining at a speed significantlyhigher than the speed commonly in use on the shop floor. In the last twenty years, high speed machining has received great attentions as a technological solution for high productivity in manufacturing. This article reviews the developments of tool materials in high speed machining operations, and the properties, applications and prospective developments of tool materials in HSM are also presented.

  3. Design of equipment for training machine tools

    Directory of Open Access Journals (Sweden)

    Císar Miroslav

    2017-01-01

    Full Text Available The article proposes multiple devices designed to be used with training machine tools EMCO Concept series. Design was focused to enchant educational potential of training machine tools located in the laboratory of CNC programing, department of automation and production systems, Faculty of mechanical engineering, University of Zilina. The described device allows monitoring of machine tool, to measure tool offset and dimension, to use alternative ways of clamping, and to create video of machining.

  4. Calibration of a Parallel Kinematic Machine Tool

    Institute of Scientific and Technical Information of China (English)

    HE Xiao-mei; DING Hong-sheng; FU Tie; XIE Dian-huang; XU Jin-zhong; LI Hua-feng; LIU Hui-lin

    2006-01-01

    A calibration method is presented to enhance the static accuracy of a parallel kinematic machine tool by using a coordinate measuring machine and a laser tracker. According to the established calibration model and the calibration experiment, the factual 42 kinematic parameters of BKX-I parallel kinematic machine tool are obtained. By circular tests the comparison is made between the calibrated and the uncalibrated parameters and shows that there is 80% improvement in accuracy of this machine tool.

  5. FORMING AND PRECISION MACHINING TO NANOMATERIALS LUMP

    Institute of Scientific and Technical Information of China (English)

    Zhan Jie; Zhang Jin; Chen Bingkui; Chen Xiaoan

    2004-01-01

    The technology of forming and machining lump nano-materials has been investigated. Grinding, abrasive machining test has been conducted to Fe, Co, Ni and Al lump nano-materials. Experiments have been done to measure grinding force, grinding thermal, machining roughness and micro-hardness. Image analysis is carried out by metallographic and scanning tunnel microscopic microscope. Researches provide the basis data for forming and machining lump nano-materials.

  6. Permutation parity machines for neural cryptography.

    Science.gov (United States)

    Reyes, Oscar Mauricio; Zimmermann, Karl-Heinz

    2010-06-01

    Recently, synchronization was proved for permutation parity machines, multilayer feed-forward neural networks proposed as a binary variant of the tree parity machines. This ability was already used in the case of tree parity machines to introduce a key-exchange protocol. In this paper, a protocol based on permutation parity machines is proposed and its performance against common attacks (simple, geometric, majority and genetic) is studied.

  7. Laser-assisted machining of difficult-to-machine materials

    Energy Technology Data Exchange (ETDEWEB)

    Incropera, F.P.; Rozzi, J.C.; Pfefferkorn, F.E.; Lei, S.; Shin, Y.C.

    1999-07-01

    Laser-assisted machining (LAM) is a hybrid process for which a difficult-to-machine material, such as a ceramic or super alloy, is irradiated by a laser source prior to material removal by a cutting tool. The process has the potential to significantly increase material removal rates, as well as to improve the geometry and properties of the finished work piece. Features and limitations of theoretical and experimental procedures for determining the transient thermal response of a work piece during LAM are described, and representative results are presented for laser-assisted turning of sintered silicon nitride. Significant physical trends are revealed by the calculations, as are guidelines for the selection of appropriate operating conditions.

  8. Mini lathe machine converted to CNC

    Directory of Open Access Journals (Sweden)

    Alexandru Morar

    2012-06-01

    Full Text Available This paper presents the adaptation of a mechanical mini-lathing machine to a computerized numerical control (CNC lathing machine. This machine is composed of a ASIST mini-lathe and a two-degrees-of-freedom XZ stage designed specifically for this application. The whole system is controlled from a PC using adequate CNC control software.

  9. Gold Rush to China for Italian Machines

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Italy exported two billion worth of textile machines in 2006, 46% of which went to Asia.China paid 365 million Euro to become the largest importer of ltaly’s machines in Aisa.China, a country that sustains Italian interest in coming,is the country where the investment in textile machines is growing...

  10. Evaluation of an improved centrifugal casting machine.

    Science.gov (United States)

    Donovan, T E; White, L E

    1985-05-01

    A Type III gold alloy, a silver-palladium alloy, and a base metal alloy were cast in two different centrifugal casting machines. With the number of complete cast mesh squares as an indicator of castability, the Airspin casting machine produced superior castings with all three alloys. The base metal alloy produced the greatest number of complete squares with both casting machines.

  11. 7 CFR 58.429 - Washing machine.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Washing machine. 58.429 Section 58.429 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards....429 Washing machine. When used, the washing machine for cheese cloths and bandages shall be...

  12. Method and apparatus for monitoring machine performance

    Science.gov (United States)

    Smith, Stephen F.; Castleberry, Kimberly N.

    1996-01-01

    Machine operating conditions can be monitored by analyzing, in either the time or frequency domain, the spectral components of the motor current. Changes in the electric background noise, induced by mechanical variations in the machine, are correlated to changes in the operating parameters of the machine.

  13. Machine scheduling with resource dependent processing times

    NARCIS (Netherlands)

    Grigoriev, A.; Sviridenko, M.; Uetz, Marc Jochen

    We consider machine scheduling on unrelated parallel machines with the objective to minimize the schedule makespan. We assume that, in addition to its machine dependence, the processing time of any job is dependent on the usage of a discrete renewable resource, e.g. workers. A given amount of that

  14. Automated solar-cell-array assembly machine

    Science.gov (United States)

    Costogue, E. N.; Mueller, R. L.; Person, J. K.; Yasui, R. K.

    1978-01-01

    Continuous-feeding machine automatically bonds solar cells to printed-circuit substrate. In completed machine, cells move to test station where electrical characteristics could be checked. If performance of cell is below specifications, that cell is marked and removed. All machine functions are synchronized by electronics located within unit. It may help to lower costs in future solar-cell production.

  15. Time-machine in Perfect Fluid Cosmologies

    Institute of Scientific and Technical Information of China (English)

    DUAN Yan-zhi

    2009-01-01

    This letter investigates the time-machine problem in perfect fluid cosmologies. It solves the Einstein's field equations with the energy-momentum tensors for perfect fluid and constructs a class of time-machine solutions,by which the time-machine problem in the perfect fluid cosmologies is solved.

  16. Patient and family requests for hastened death.

    Science.gov (United States)

    Abrahm, Janet L

    2008-01-01

    Patient and family requests for hastened death, upsetting as they are to the treating team, are usually a way for patients and their families to express their need for an increase in the intensity of communication, improved symptom control, or acknowledgment of an existential or spiritual crisis. Rarely do they represent the need for patients to control the time, place, and manner of their death. Using a hypothetical case study, this paper reviews the unspoken concerns underlying these requests; characteristics of patients who request a hastened death, and when and why they make the request; the Oregon Death with Dignity Act and its implementation since its passage in 1997; the effect these requests have on clinicians, their common reactions, and suggestions for self-care after such requests; techniques for responding to the requests and keeping the dialogue open with the patient and family; and the legal and ethical options available to clinicians outside of Oregon.

  17. Energy Analysis of Contention Tree-Based Access Protocols in Dense Machine-to-Machine Area Networks

    Directory of Open Access Journals (Sweden)

    Francisco Vázquez-Gallego

    2015-01-01

    Full Text Available Machine-to-Machine (M2M area networks aim at connecting an M2M gateway with a large number of energy-constrained devices that must operate autonomously for years. Therefore, attaining high energy efficiency is essential in the deployment of M2M networks. In this paper, we consider a dense M2M area network composed of hundreds or thousands of devices that periodically transmit data upon request from a gateway or coordinator. We theoretically analyse the devices’ energy consumption using two Medium Access Control (MAC protocols which are based on a tree-splitting algorithm to resolve collisions among devices: the Contention Tree Algorithm (CTA and the Distributed Queuing (DQ access. We have carried out computer-based simulations to validate the accuracy of the theoretical models and to compare the energy performance using DQ, CTA, and Frame Slotted-ALOHA (FSA in M2M area networks with devices in compliance with the IEEE 802.15.4 physical layer. Results show that the performance of DQ is totally independent of the number of contending devices, and it can reduce the energy consumed per device in more than 35% with respect to CTA and in more than 80% with respect to FSA.

  18. Trusted Virtual Machine Allocation in Cloud Computing IaaS Service

    Directory of Open Access Journals (Sweden)

    A. Radhakrishnan

    2014-04-01

    Full Text Available Cloud computing is a new era in computing paradigm. It helps Information Technology (IT companies to cut the cost by outsourcing data and computation on-demand. Cloud computing provides different kind of services which includes Hardware as a Service, Software as a Service (SaaS, Infrastructure as a Service (IaaS etc. Despite these potential benefits, many IT companies are reluctant to do cloud business due to outstanding trust issues. Cloud consumer and provider are the most interested parties to maximize their benefits. In IaaS, the cloud provider operates the whole computing platform as a resource for the customer, which is accessed by customer as a Virtual Machine (VM via the internet. The cloud provider must predict the best machine among the available machines to launch VM. This strategic prediction would avoid exodus of computation in middle due to machine heavy load or any failure which severely affect the benefits of both consumer and provider. Since VM allocation for IaaS request is a challenging task, in this study novel architecture is proposed for IaaS cloud computing environment in which VM allocation is done through genetically weight optimized neural network. In this scenario the host load of each machine is taken as its resource information. The neural network predicts the host load of each machine in near future based on the recent past host load. It would help the VM allocator to choose the right machine. Analysis is done on the performance of genetically weight optimized Back Propagation Neural Network (BPNN, Elman Neural Network (ELNN and Jordan Neural Network (JNN for prediction accuracy.

  19. Identifying Cross-Sided Liquidity Externalities

    NARCIS (Netherlands)

    J.A. Skjeltorp (Johannes); E. Sojli (Elvira); W.W. Tham (Wing Wah)

    2013-01-01

    markdownabstract__Abstract__ We study the relevance of the cross-sided externality between liquidity makers and takers from the two-sided market perspective. We use exogenous changes in the make/take fee structure, minimum tick-size and technological shocks for liquidity takers and makers, as exper

  20. 7 CFR 29.6035 - Side.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Side. 29.6035 Section 29.6035 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Standards Definitions § 29.6035 Side. A certain phase of quality as contrasted with some...

  1. Managing Chemotherapy Side Effects: Nausea and Vomiting

    Science.gov (United States)

    ... boiled, without the skin ••White rice ••White toast ••Bananas ••Canned fruit such as applesauce, peaches, and pears •• ... has a series of 18 Chemotherapy Side Effects Sheets at: www.cancer.gov/chemo-side-effects

  2. MACHINING OPTIMISATION AND OPERATION ALLOCATION FOR NC LATHE MACHINES IN A JOB SHOP MANUFACTURING SYSTEM

    Directory of Open Access Journals (Sweden)

    MUSSA I. MGWATU

    2013-08-01

    Full Text Available Numerical control (NC machines in a job shop may not be cost and time effective if the assignment of cutting operations and optimisation of machining parameters are overlooked. In order to justify better utilisation and higher productivity of invested NC machine tools, it is necessary to determine the optimum machining parameters and realize effective assignment of cutting operations on machines. This paper presents two mathematical models for optimising machining parameters and effectively allocating turning operations on NC lathe machines in a job shop manufacturing system. The models are developed as non-linear programming problems and solved using a commercial LINGO software package. The results show that the decisions of machining optimisation and operation allocation on NC lathe machines can be simultaneously made while minimising both production cost and cycle time. In addition, the results indicate that production cost and cycle time can be minimised while significantly reducing or totally eliminating idle times among machines.

  3. Method and apparatus for mining machine cutter head

    Energy Technology Data Exchange (ETDEWEB)

    Mann, J.P.; Levenstein, V.M.; Fox, C.H.

    1987-03-10

    This patent describes a continuous mining machine having a frame assembly pivotally attached to the machine and a rotary cutting head mounted on a shaft on the forward end of the frame assembly and having cutting bits thereon for cutting loose mining material from the face of a mine and extending beyond each side of the frame assembly. The improvement described here comprises: a. at least one bearing mounted on the cutting head shaft for enabling rotation of the shaft, b. at least one C-shaped bearing support housing on the forward end of the frame assembly for receiving the bearing on the shaft, c. a matching removable C-shaped bearing support end cap for attachment to the frame assembly C-shaped bearing support housing for encompassing and supporting the shaft bearing for rotation of the shaft. This is used so that the shaft may be removed from the mining machine without lateral movement of the shaft by removing the matching removable C-shaped bearing support housing, and d. drive means coupled to the cutting head shaft to provide rotary motion thereto for cutting mining material.

  4. Back-side readout semiconductor photomultiplier

    Science.gov (United States)

    Choong, Woon-Seng; Holland, Stephen E

    2014-05-20

    This disclosure provides systems, methods, and apparatus related to semiconductor photomultipliers. In one aspect, a device includes a p-type semiconductor substrate, the p-type semiconductor substrate having a first side and a second side, the first side of the p-type semiconductor substrate defining a recess, and the second side of the p-type semiconductor substrate being doped with n-type ions. A conductive material is disposed in the recess. A p-type epitaxial layer is disposed on the second side of the p-type semiconductor substrate. The p-type epitaxial layer includes a first region proximate the p-type semiconductor substrate, the first region being implanted with p-type ions at a higher doping level than the p-type epitaxial layer, and a second region disposed on the first region, the second region being doped with p-type ions at a higher doping level than the first region.

  5. A Typology of Multi-sided Platforms

    DEFF Research Database (Denmark)

    Staykova, Kalina Stefanova; Damsgaard, Jan

    2015-01-01

    exemplary cases which allow us to illustrate the platform heterogeneity and to support new MSPs typology. As examples we include a physical two-sided platform (Gatwick Airport) that adds a third side, a digital one-sided platform transformed into being two-sided (Pingit) and a digital one-sided platform......In this paper we address how the composition of a platform impacts the platform’s business model. By platform’s business model we mean platform features, platform architecture and platform governance. To this end, we construct the Platform Business Model Framework. We apply the framework to three...... in several configurations. The particular platform architecture can explain the difficulties in designing a viable business models for platforms....

  6. Temperature based Restricted Boltzmann Machines.

    Science.gov (United States)

    Li, Guoqi; Deng, Lei; Xu, Yi; Wen, Changyun; Wang, Wei; Pei, Jing; Shi, Luping

    2016-01-13

    Restricted Boltzmann machines (RBMs), which apply graphical models to learning probability distribution over a set of inputs, have attracted much attention recently since being proposed as building blocks of multi-layer learning systems called deep belief networks (DBNs). Note that temperature is a key factor of the Boltzmann distribution that RBMs originate from. However, none of existing schemes have considered the impact of temperature in the graphical model of DBNs. In this work, we propose temperature based restricted Boltzmann machines (TRBMs) which reveals that temperature is an essential parameter controlling the selectivity of the firing neurons in the hidden layers. We theoretically prove that the effect of temperature can be adjusted by setting the parameter of the sharpness of the logistic function in the proposed TRBMs. The performance of RBMs can be improved by adjusting the temperature parameter of TRBMs. This work provides a comprehensive insights into the deep belief networks and deep learning architectures from a physical point of view.

  7. Reliability analysis in intelligent machines

    Science.gov (United States)

    Mcinroy, John E.; Saridis, George N.

    1990-01-01

    Given an explicit task to be executed, an intelligent machine must be able to find the probability of success, or reliability, of alternative control and sensing strategies. By using concepts for information theory and reliability theory, new techniques for finding the reliability corresponding to alternative subsets of control and sensing strategies are proposed such that a desired set of specifications can be satisfied. The analysis is straightforward, provided that a set of Gaussian random state variables is available. An example problem illustrates the technique, and general reliability results are presented for visual servoing with a computed torque-control algorithm. Moreover, the example illustrates the principle of increasing precision with decreasing intelligence at the execution level of an intelligent machine.

  8. Machine learning a probabilistic perspective

    CERN Document Server

    Murphy, Kevin P

    2012-01-01

    Today's Web-enabled deluge of electronic data calls for automated methods of data analysis. Machine learning provides these, developing methods that can automatically detect patterns in data and then use the uncovered patterns to predict future data. This textbook offers a comprehensive and self-contained introduction to the field of machine learning, based on a unified, probabilistic approach. The coverage combines breadth and depth, offering necessary background material on such topics as probability, optimization, and linear algebra as well as discussion of recent developments in the field, including conditional random fields, L1 regularization, and deep learning. The book is written in an informal, accessible style, complete with pseudo-code for the most important algorithms. All topics are copiously illustrated with color images and worked examples drawn from such application domains as biology, text processing, computer vision, and robotics. Rather than providing a cookbook of different heuristic method...

  9. Attractor Control Using Machine Learning

    CERN Document Server

    Duriez, Thomas; Noack, Bernd R; Cordier, Laurent; Segond, Marc; Abel, Markus

    2013-01-01

    We propose a general strategy for feedback control design of complex dynamical systems exploiting the nonlinear mechanisms in a systematic unsupervised manner. These dynamical systems can have a state space of arbitrary dimension with finite number of actuators (multiple inputs) and sensors (multiple outputs). The control law maps outputs into inputs and is optimized with respect to a cost function, containing physics via the dynamical or statistical properties of the attractor to be controlled. Thus, we are capable of exploiting nonlinear mechanisms, e.g. chaos or frequency cross-talk, serving the control objective. This optimization is based on genetic programming, a branch of machine learning. This machine learning control is successfully applied to the stabilization of nonlinearly coupled oscillators and maximization of Lyapunov exponent of a forced Lorenz system. We foresee potential applications to most nonlinear multiple inputs/multiple outputs control problems, particulary in experiments.

  10. Differentially Private Support Vector Machines

    CERN Document Server

    Sarwate, Anand; Monteleoni, Claire

    2009-01-01

    This paper addresses the problem of practical privacy-preserving machine learning: how to detect patterns in massive, real-world databases of sensitive personal information, while maintaining the privacy of individuals. Chaudhuri and Monteleoni (2008) recently provided privacy-preserving techniques for learning linear separators via regularized logistic regression. With the goal of handling large databases that may not be linearly separable, we provide privacy-preserving support vector machine algorithms. We address general challenges left open by past work, such as how to release a kernel classifier without releasing any of the training data, and how to tune algorithm parameters in a privacy-preserving manner. We provide general, efficient algorithms for linear and nonlinear kernel SVMs, which guarantee $\\epsilon$-differential privacy, a very strong privacy definition due to Dwork et al. (2006). We also provide learning generalization guarantees. Empirical evaluations reveal promising performance on real and...

  11. Finite State Machine based Vending Machine Controller with Auto-Billing Features

    OpenAIRE

    2012-01-01

    Nowadays, Vending Machines are well known among Japan, Malaysia and Singapore. The quantity of machines in these countries is on the top worldwide. This is due to the modern lifestyles which require fast food processing with high quality. This paper describes the designing of multi select machine using Finite State Machine Model with Auto-Billing Features. Finite State Machine (FSM) modelling is the most crucial part in developing proposed model as this reduces the hardware. In this paper th...

  12. Study On Machining Processing Technology Risk Control

    Institute of Scientific and Technical Information of China (English)

    Li Xiqing

    2015-01-01

    In the industrial production process,only to ful y guarantee the machining production safety, it can been ensured that the smooth completion of machining process.Under this back ground,in the machining production process,the machinery processing safety would been ful y concerned,several factors, which may lead to the problem of mechanical processing and production process,were analyzed,and the relevant control strategies were researched.In view of this situation,this paper wil specifical y combined with the machining process characteristics to study the machining process manufacturability risk control.

  13. EXPERIMENTAL EVALUATION OF WEDM MACHINED SURFACE WAVINESS

    Directory of Open Access Journals (Sweden)

    Katerina Mouralova

    2016-10-01

    Full Text Available Wire Electrical Discharge Machining (WEDM an unconventional machining technology which has become indispensable in many industries. The typical morphology of a surface machined using the electrical discharge technology is characterized with a large number of craters caused by electro-spark discharges produced during the machining process. The study deals with an evaluation of the machine parameter setting on the profile parameters of surface waviness on samples made of two metal materials Al 99.5 and Ti-6Al-4V. Attention was also paid to an evaluation of the surface morphology using 3D colour filtered and non-filtered images.

  14. A New Incremental Support Vector Machine Algorithm

    Directory of Open Access Journals (Sweden)

    Wenjuan Zhao

    2012-10-01

    Full Text Available Support vector machine is a popular method in machine learning. Incremental support vector machine algorithm is ideal selection in the face of large learning data set. In this paper a new incremental support vector machine learning algorithm is proposed to improve efficiency of large scale data processing. The model of this incremental learning algorithm is similar to the standard support vector machine. The goal concept is updated by incremental learning. Each training procedure only includes new training data. The time complexity is independent of whole training set. Compared with the other incremental version, the training speed of this approach is improved and the change of hyperplane is reduced.

  15. Selected problems relating to the dynamics of block-type foundations for machines

    Directory of Open Access Journals (Sweden)

    Marek Zombroń

    2014-07-01

    Full Text Available Atypical but real practical problems relating to the dynamics of block-type foundations for machines are considered using the deterministic approach and assuming that the determined parameters are random variables. A foundation model in the form of an undeformable solid on which another undeformable solid modelling a machine is mounted via viscoelastic constraints was adopted. The dynamic load was defined by a harmonically varying signal and by a series of short duration signals. The vibration of the system was investigated for the case when stratified ground (groundwater occurred within the side backfill was present. Calculation results illustrating the theoretical analyses are presented.

  16. Strategies for measuring machine consciousness

    OpenAIRE

    2009-01-01

    The accurate measurement of the level of consciousness of a creature remains a major scientific challenge, nevertheless a number of new accounts that attempt to address this problem have been proposed recently. In this paper we analyze the principles of these new measures of consciousness along with other classical approaches focusing on their applicability to Machine Consciousness (MC). Furthermore, we propose a set of requirements of what we think a suitable measure for MC should be, discus...

  17. Machine vision theory, algorithms, practicalities

    CERN Document Server

    Davies, E R

    2005-01-01

    In the last 40 years, machine vision has evolved into a mature field embracing a wide range of applications including surveillance, automated inspection, robot assembly, vehicle guidance, traffic monitoring and control, signature verification, biometric measurement, and analysis of remotely sensed images. While researchers and industry specialists continue to document their work in this area, it has become increasingly difficult for professionals and graduate students to understand the essential theory and practicalities well enough to design their own algorithms and systems. This book directl

  18. The bacteriophage DNA packaging machine.

    Science.gov (United States)

    Feiss, Michael; Rao, Venigalla B

    2012-01-01

    Large dsDNA bacteriophages and herpesviruses encode a powerful ATP-driven DNA-translocating machine that encapsidates a viral genome into a preformed capsid shell or prohead. The key components of the packaging machine are the packaging enzyme (terminase, motor) and the portal protein that forms the unique DNA entrance vertex of prohead. The terminase complex, comprised of a recognition subunit (small terminase) and an endonuclease/translocase subunit (large terminase), cuts viral genome concatemers. The terminase-viral DNA complex docks on the portal vertex, assembling a motor complex containing five large terminase subunits. The pentameric motor processively translocates DNA until the head shell is full with one viral genome. The motor cuts the DNA again and dissociates from the full head, allowing head-finishing proteins to assemble on the portal, sealing the portal, and constructing a platform for tail attachment. A body of evidence from molecular genetics and biochemical, structural, and biophysical approaches suggests that ATP hydrolysis-driven conformational changes in the packaging motor (large terminase) power DNA motion. Various parts of the motor subunit, such as the ATPase, arginine finger, transmission domain, hinge, and DNA groove, work in concert to translocate about 2 bp of DNA per ATP hydrolyzed. Powerful single-molecule approaches are providing precise delineation of steps during each translocation event in a motor that has a speed as high as a millisecond/step. The phage packaging machine has emerged as an excellent model for understanding the molecular machines, given the mechanistic parallels between terminases, helicases, and numerous motor proteins.

  19. Waterless Clothes-Cleaning Machine

    Science.gov (United States)

    Johnson, Glenn; Ganske, Shane

    2013-01-01

    A waterless clothes-cleaning machine has been developed that removes loose particulates and deodorizes dirty laundry with regenerative chemical processes to make the clothes more comfortable to wear and have a fresher smell. This system was initially developed for use in zero-g, but could be altered for 1-g environments where water or other re sources are scarce. Some of these processes include, but are not limited to, airflow, filtration, ozone generation, heat, ultraviolet light, and photocatalytic titanium oxide.

  20. Media-Augmented Exercise Machines

    Science.gov (United States)

    Krueger, T.

    2002-01-01

    Cardio-vascular exercise has been used to mitigate the muscle and cardiac atrophy associated with adaptation to micro-gravity environments. Several hours per day may be required. In confined spaces and long duration missions this kind of exercise is inevitably repetitive and rapidly becomes uninteresting. At the same time, there are pressures to accomplish as much as possible given the cost- per-hour for humans occupying orbiting or interplanetary. Media augmentation provides a the means to overlap activities in time by supplementing the exercise with social, recreational, training or collaborative activities and thereby reducing time pressures. In addition, the machine functions as an interface to a wide range of digital environments allowing for spatial variety in an otherwise confined environment. We hypothesize that the adoption of media augmented exercise machines will have a positive effect on psycho-social well-being on long duration missions. By organizing and supplementing exercise machines, data acquisition hardware, computers and displays into an interacting system this proposal increases functionality with limited additional mass. This paper reviews preliminary work on a project to augment exercise equipment in a manner that addresses these issues and at the same time opens possibilities for additional benefits. A testbed augmented exercise machine uses a specialty built cycle trainer as both input to a virtual environment and as an output device from it using spatialized sound, and visual displays, vibration transducers and variable resistance. The resulting interactivity increases a sense of engagement in the exercise, provides a rich experience of the digital environments. Activities in the virtual environment and accompanying physiological and psychological indicators may be correlated to track and evaluate the health of the crew.