WorldWideScience

Sample records for m3 spectral range

  1. The Moon Mineralogy (M3) Imaging Spectrometer: Early Assessment of the Spectral, Radiometric, Spatial and Uniformity Properties

    Science.gov (United States)

    Green, Robert O.; Pieters, C. M.; Boardman, J.; Barr, D.; Bruce, C.; Bousman, J.; Chatterjee, A.; Eastwood, M.; Essandoh, V.; Geier, S.; Glavich, T.; Green, R.; Haemmerle, V.; Hyman, S.; Hovland, L.; Koch, T.; Lee, K.; Lundeen, S.; Motts, E.; Mouroulis, P.; Paulson, S.; Plourde, K.; Racho, C.; Robinson, D.; Rodriquez, J.

    2009-01-01

    The Moon Mineralogy Mapper's (M3) is a high uniformity and high signal-to-noise ratio NASA imaging spectrometer that is a guest instrument on the Indian Chandrayaan-1 Mission to the Moon. The laboratory measured spectral, radiometric, spatial, and uniformity characteristics of the M3 instrument are given. The M3 imaging spectrometer takes advantage of a suite of critical enabling capabilities to achieve its measurement requirement with a mass of 8 kg, power usage of 15 W, and volume of 25X18X12 cm. The M3 detector and spectrometer are cooled by a multi-stage passive cooler. This paper presents early M3 performance assessment results.

  2. Full Stokes observations in the He I 1083 nm spectral region covering an M3.2 flare

    CERN Document Server

    Kuckein, C; Sainz, R Manso; Ramos, A Asensio

    2015-01-01

    We present an exceptional data set acquired with the Vacuum Tower Telescope (Tenerife, Spain) covering the pre-flare, flare, and post-flare stages of an M3.2 flare. The full Stokes spectropolarimetric observations were recorded with the Tenerife Infrared Polarimeter in the He I 1083.0 nm spectral region. The object under study was active region NOAA 11748 on 2013 May 17. During the flare the chomospheric He I 1083.0 nm intensity goes strongly into emission. However, the nearby photospheric Si I 1082.7 nm spectral line profile only gets shallower and stays in absorption. Linear polarization (Stokes Q and U) is detected in all lines of the He I triplet during the flare. Moreover, the circular polarization (Stokes V) is dominant during the flare, being the blue component of the He I triplet much stronger than the red component, and both are stronger than the Si I Stokes V profile. The Si I inversions reveal enormous changes of the photospheric magnetic field during the flare. Before the flare magnetic field conc...

  3. Characterisation of red supergiants in the Gaia spectral range

    Science.gov (United States)

    Dorda, Ricardo; González-Fernández, Carlos; Negueruela, Ignacio

    2016-11-01

    Context. The infrared calcium triplet and its nearby spectral region have been used for spectral and luminosity classification of late-type stars, but the samples of cool supergiants (CSGs) used have been very limited (in size, metallicity range, and spectral types covered). The spectral range of the Gaia Radial Velocity Spectrograph (RVS) covers most of this region but does not reach the main TiO bands in this region, whose depths define the M sequence. Aims: We study the behaviour of spectral features around the calcium triplet and develop effective criteria to identify and classify CSGs, comparing their efficiency with other methods previously proposed. Methods: We measure the main spectral features in a large sample (almost 600) of red supergiants (RSGs) from three different galaxies, and we analyse their behaviour through a principal component analysis. Using the principal components, we develop an automatised method to differentiate CSGs from other bright late-type stars, and to classify them. Results: The proposed method identifies a high fraction (0.98 ± 0.04) of the supergiants in our test sample, which cover a wide metallicity range (supergiants from the Magellanic Clouds and the Milky Way) and with spectral types from G0 up to late-M. In addition, it is capable to separate most of the non-supergiants in the sample, identifying as supergiants only a very small fraction of them (0.02 ± 0.04). A comparison of this method with other previously proposed shows that it is more efficient and selects less interlopers. A way to automatically assign a spectral type to the supergiants is also developed. We apply this study to spectra at the resolution and spectral range of the Gaia RVS, with a similar success rate. Conclusions: The method developed identifies and classifies CSGs in large samples, with high efficiency and low contamination, even in conditions of wide metallicity and spectral-type ranges. As this method uses the infrared calcium triplet spectral

  4. Adaptive optimal spectral range for dynamically changing scene

    Science.gov (United States)

    Pinsky, Ephi; Siman-tov, Avihay; Peles, David

    2012-06-01

    A novel multispectral video system that continuously optimizes both its spectral range channels and the exposure time of each channel autonomously, under dynamic scenes, varying from short range-clear scene to long range-poor visibility, is currently being developed. Transparency and contrast of high scattering medium of channels with spectral ranges in the near infrared is superior to the visible channels, particularly to the blue range. Longer wavelength spectral ranges that induce higher contrast are therefore favored. Images of 3 spectral channels are fused and displayed for (pseudo) color visualization, as an integrated high contrast video stream. In addition to the dynamic optimization of the spectral channels, optimal real-time exposure time is adjusted simultaneously and autonomously for each channel. A criterion of maximum average signal, derived dynamically from previous frames of the video stream is used (Patent Application - International Publication Number: WO2009/093110 A2, 30.07.2009). This configuration enables dynamic compatibility with the optimal exposure time of a dynamically changing scene. It also maximizes the signal to noise ratio and compensates each channel for the specified value of daylight reflections and sensors response for each spectral range. A possible implementation is a color video camera based on 4 synchronized, highly responsive, CCD imaging detectors, attached to a 4CCD dichroic prism and combined with a common, color corrected, lens. Principal Components Analysis (PCA) technique is then applied for real time "dimensional collapse" in color space, in order to select and fuse, for clear color visualization, the 3 most significant principal channels out of at least 4 characterized by high contrast and rich details in the image data.

  5. Characterisation of red supergiants in the Gaia spectral range

    CERN Document Server

    Dorda, Ricardo; Negueruela, Ignacio

    2016-01-01

    The infrared Calcium Triplet and its nearby spectral region have been used for spectral and luminosity classification of late-type stars, but the samples of cool supergiants (CSGs) used have been very limited (in size, metallicity range, and spectral types covered). The spectral range of the Gaia Radial Velocity Spectrograph (RVS) covers most of this region but does not reach the main TiO bands in this region, whose depths define the M sequence. We study the behaviour of spectral features around the Calcium Triplet and develop effective criteria to identify and classify CSGs, comparing their efficiency with other methods previously proposed. We measure the main spectral features in a large sample (almost 600) of CSGs from three different galaxies, and we analyse their behaviour through a principal component analysis. Using the principal components, we develop an automatised method to differentiate CSGs from other bright late-type stars, and to classify them. The proposed method identifies a high fraction of t...

  6. Broad spectral range synchronized flat-top arrayed waveguide grating

    NARCIS (Netherlands)

    Akca, B. Imran; Doerr, Christopher R.; Pollnau, Markus; Ridder, de René M.

    2012-01-01

    A broad-band Mach-Zehnder-interferometer-synchronized flat-top arrayed waveguide grating is presented with a 0.5-dB bandwidth of 12 nm over 90 nm of spectral range and a central excess loss value of -0.5 dB.

  7. A wide spectral range photoacoustic aerosol absorption spectrometer.

    Science.gov (United States)

    Haisch, C; Menzenbach, P; Bladt, H; Niessner, R

    2012-11-06

    A photoacoustic spectrometer for the measurement of aerosol absorption spectra, based on the excitation of a pulsed nanosecond optical parametrical oscillator (OPO), will be introduced. This spectrometer is working at ambient pressure and can be used to detect and characterize different classes of aerosols. The spectrometer features a spectral range of 410 to 2500 nm and a sensitivity of 2.5 × 10(-7) m(-1) at 550 nm. A full characterization of the system in the visible spectral range is demonstrated, and the potential of the system for near IR measurement is discussed. In the example of different kinds of soot particles, the performance of the spectrometer was assessed. As we demonstrate, it is possible to determine a specific optical absorption per particle by a combination of the new spectrometer with an aerosol particle counter.

  8. Innovative static spectropolarimeter concept for wide spectral ranges: tolerancing study

    CERN Document Server

    Pertenais, Martin; Parès, Laurent; Petit, Pascal

    2015-01-01

    Developing an efficient and robust polarimeter for wide spectral ranges and space applications is a main issue in many projects. As part of the UVMag consortium created to develop UV facilities in space (e.g. the Arago mission proposed to ESA), we are studying an innovative concept of polarimeter that is robust, simple, and efficient on a wide spectral range. The idea, based on the article by Sparks et al. (2012), is to use polarization scramblers to create a spatial modulation of the polarization. Along the height of the wedges of the scramblers, the thickness of the birefringent material crossed by the light, and thus the retardance, vary continuously. This variation creates an intensity modulation of the light related to the entrance polarization state. Analyzing this modulation with a linear polarizer, and dispersing the light spectrally in the orthogonal spatial direction, enables the measurement of the full Stokes vector over the entire spectrum. This determination is performed with a single-shot measur...

  9. Novel spectral range expansion method for liquid crystal adaptive optics.

    Science.gov (United States)

    Mu, Quanquan; Cao, Zhaoliang; Hu, Lifa; Liu, Yonggang; Peng, Zenghui; Xuan, Li

    2010-10-11

    Energy loss is a main problem of liquid crystal adaptive optics systems (LC AOSs). It is caused by the polarization dependence and narrow spectral range. The polarization dependence has been avoided by Love and Mu et al. [Appl. Opt. 32, 2222 (1993); Appl. Opt. 47, 4297 (2008)]. In this paper, a novel method was proposed to extend the spectral range of LC AOSs using multiple liquid crystal wavefront correctors (LCWFCs) to improve the energy utilization. Firstly, the chromatism of an LCWFC was measured and analyzed. The calculated results indicate that one LCWFC is only suitable to perform adaptive correction for a narrow waveband; therefore, multiple LCWFCs must be used to achieve a broadband correction. Secondly, based on open-loop control, a novel optical layout consisting of three LCWFCs was proposed to extend the spectral range of LC AOSs and thus achieve correction in the whole waveband of 520-810 nm. Thirdly, a broadband correction experiment was conducted and near diffraction-limited resolution was achieved in the waveband of 520-690 nm. Finally, a 500 m horizontal turbulence correction experiment was performed in the waveband of 520-690 nm. With adaptive correction, the resolution of the optical system was improved significantly and the image of the single fiber was clearly resolved. Furthermore, compared with a sub-waveband system, the system energy was improved. The energy of the whole waveband is equal to the sum of all the sub-wavebands. The experiment results validated our method and indicate that the chromatism in a broad waveband of LC AOSs can be eliminated. And then, the system energy can be improved greatly using the novel method.

  10. Wide spectral range characterization of antireflective coatings and their optimization

    Science.gov (United States)

    Franta, Daniel; Nečas, David; Ohlídal, Ivan; Jankuj, Jiří

    2015-09-01

    Development of antireflective coatings realized by thin film systems requires their characterization and optimization of their properties. Functional properties of such interference devices are determined by optical constants and thicknesses of the individual films and various defects taking place in these systems. In optics industry the characterization of the films is mostly performed in a relatively narrow spectral range using simple dispersion models and, moreover, the defects are not taken into account at all. This manner of characterization fails if applied to real-world non-ideal thin film systems because the measured data do not contain sufficient information about all the parameters describing the system including imperfections. Reliable characterization requires the following changes: extension of spectral range of measurements, combination of spectrophotometry and ellipsometry, utilization of physically correct dispersion models (Kramers-Kronig consistency, sum rules), inclusion of structural defects instrument imperfection into the models and simultaneous processing of all experimental data. This enables us to remove or reduce a correlation among the parameters searched so that correct and sufficiently precise determination of parameter values is achieved. Since the presence and properties of the defects are difficult to control independently by tuning of the deposition conditions, the optimization does not in general involve the elimination of defects. Instead they are taken into account in the design of the film systems. The outlined approach is demonstrated on the characterization and optimization of ultraviolet antireflective coating formed by double layer of Al2O3 and MgF2 deposited on fused silica.

  11. Method for detection and imaging over a broad spectral range

    Science.gov (United States)

    Yefremenko, Volodymyr; Gordiyenko, Eduard; Pishko, legal representative, Olga; Novosad, Valentyn; Pishko, deceased; Vitalii

    2007-09-25

    A method of controlling the coordinate sensitivity in a superconducting microbolometer employs localized light, heating or magnetic field effects to form normal or mixed state regions on a superconducting film and to control the spatial location. Electron beam lithography and wet chemical etching were applied as pattern transfer processes in epitaxial Y--Ba--Cu--O films. Two different sensor designs were tested: (i) a 3 millimeter long and 40 micrometer wide stripe and (ii) a 1.25 millimeters long, and 50 micron wide meandering-like structure. Scanning the laser beam along the stripe leads to physical displacement of the sensitive area, and, therefore, may be used as a basis for imaging over a broad spectral range. Forming the superconducting film as a meandering structure provides the equivalent of a two-dimensional detector array. Advantages of this approach are simplicity of detector fabrication, and simplicity of the read-out process requiring only two electrical terminals.

  12. A New and Inexpensive Pyranometer for the Visible Spectral Range

    Directory of Open Access Journals (Sweden)

    Miguel A. Martínez

    2009-06-01

    Full Text Available This paper presents the design, construction and testing of a new photodiode-based pyranometer for the visible spectral range (approx. 400 to 750 nm, whose principal characteristics are: accuracy, ease of connection, immunity to noise, remote programming and operation, interior temperature regulation, cosine error minimisation and all this at a very low cost, tens of times lower than that of commercial thermopile-based devices. This new photodiode-based pyranometer overcomes traditional problems in this type of device and offers similar characteristics to those of thermopile-based pyranometers and, therefore, can be used in any installation where reliable measurement of solar irradiance is necessary, especially in those where cost is a deciding factor in the choice of a meter. This new pyranometer has been registered in the Spanish Patent and Trademark Office under the number P200703162.

  13. Laser Meter of Atmospheric Inhomogeneity Properties in UV Spectral Range

    Directory of Open Access Journals (Sweden)

    S. E. Ivanov

    2015-01-01

    Full Text Available Development of laser systems designed to operate in conditions of the terrestrial atmosphere demands reliable information about the atmosphere condition. The aerosol lidars for operational monitoring of the atmosphere allow us to define remotely characteristics of atmospheric aerosol and cloudy formations in the atmosphere.Today the majority of aerosol lidars run in the visible range. However, in terms of safety (first of all to eyes also ultra-violet (UF range is of interest. A range of the wavelengths of the harmful effect on the eye retina is from 0.38 to 1.4 mμ. Laser radiation with the wavelengths less than 0.38 mμ and over 1.4 mμ influences the anterior ambient of an eye and is safer, than laser radiation with the wavelengths of 0.38 – 1.4 mμ.The paper describes a laser meter to measure characteristics of atmospheric inhomogeneity propertis in UF spectral range at the wavelength of 0.355 mμ.As a radiation source, the meter uses a semiconductor-pumped pulse solid-state Nd:YAG laser. As a receiving lens, Kassegren's scheme-implemented mirror lens with a socket to connect optical fibre is used in the laser meter. Radiation from the receiving lens is transported through the optical fibre to the optical block. The optical block provides spectral selection of useful signal and conversion of optical radiation into electric signal.To ensure a possibility for alignment of the optical axes of receiving lens and laser radiator the lens is set on the alignment platform that enables changing lens inclination and turn with respect to the laser.The software of the laser meter model is developed in the NI LabVIEW 2012 graphic programming environment.The paper gives the following examples: a typical laser echo signal, which is back scattered by the atmosphere and spatiotemporal distribution of variation coefficient of the volumetric factor of the back scattered atmosphere. Results of multi-day measurements show that an extent of the recorded aerosol

  14. Single-order operation of lamellar multilayer gratings in the soft x-ray spectral range

    NARCIS (Netherlands)

    Meer, van der R.; Kozhevnikov, I.V.; Krishnan, B.; Huskens, J.; Hegeman, P.E.; Brons, C.; Vratzov, B.; Bastiaens, H.M.J.; Boller, K-J.; Bijkerk, F.

    2013-01-01

    We demonstrate single-order operation of Lamellar Multilayer Gratings in the soft x-ray spectral range. The spectral resolution was found to be 3.8 times higher than from an unpatterned multilayer mirror, while there were no significant spectral sideband structures adjacent to the main Bragg peak. T

  15. Single-order operation of lamellar multilayer gratings in the soft x-ray spectral range

    Directory of Open Access Journals (Sweden)

    Robert van der Meer

    2013-01-01

    Full Text Available We demonstrate single-order operation of Lamellar Multilayer Gratings in the soft x-ray spectral range. The spectral resolution was found to be 3.8 times higher than from an unpatterned multilayer mirror, while there were no significant spectral sideband structures adjacent to the main Bragg peak. The measured spectral bandwidths and peak reflectivities were in good agreement with our theoretical calculations.

  16. Airborne hyperspectral imaging in the visible-to-mid wave infrared spectral range by fusing three spectral sensors

    Science.gov (United States)

    Jakovels, Dainis; Filipovs, Jevgenijs; Erinš, Gatis; Taskovs, Juris

    2014-10-01

    Airborne hyperspectral imaging is widely used for remote sensing of environment. The choice of spectral region usually depends on the availability and cost of the sensor. Visible-to-near infrared (400-1100 nm) spectral range corresponds to spectral sensitivity of relatively cheap Si detectors therefore it is the most commonly used. The implementation of shortwave infrared (1100-3000 nm) requires more expensive solutions, but can provide valuable information about the composition of the substance. Mid wave infrared (3000-8000 nm) is rarely used for civilian applications, but it provides information on the thermal emission of materials. The fusion of different sensors allows spectral analysis of a wider spectral range combining and improving already existing algorithms for the analysis of chemical content and classification. Here we introduce our Airborne Surveillance and Environmental Monitoring System (ARSENAL) that was developed by fusing seven sensors. The first test results from the fusion of three hyperspectral imaging sensors in the visible-to-mid wave infrared (365-5000 nm) are demonstrated. Principal component analysis (PCA) is applied to test correlation between principal components (PCs) and common vegetation indices.

  17. The properties of ITE's silicon avalanche photodiodes within the spectral range used in scintillation detection

    CERN Document Server

    Wegrzecka, I

    1999-01-01

    The design and properties of 3 mm silicon avalanche photodiodes developed at ITE are presented. Their performance parameters within the spectral range applicable in scintillation detection (400-700 nm) are discussed and compared to those for near infrared radiation.

  18. Transmittance, Reflectance, and Emission Spectroscopy of Meteorites from the UV to the IR Spectral Range

    Science.gov (United States)

    Maturilli, A.; Helbert, J.; Koulen, J. M.; Ferrari, S.; Martellato, E.

    2016-08-01

    Transmittance, reflectance, and emissivity Spectra of six meteorites have been collected at the Planetary Spectroscopy Laboratory (PSL) of DLR in Berlin in the whole spectral range from the UV to the IR.

  19. New confocal microscopy hyperspectral imager for NIR-emitting bioprobes: high spectral resolution for a wide spectral range (Conference Presentation)

    Science.gov (United States)

    Marcet, Stéphane; Benayas, Antonio; Quintanilla, Marta; Mangiarini, Francesca; Verhaegen, Marc; Vetrone, Fiorenzo; Blais-Ouellette, Sébastien

    2016-03-01

    Functional nanoscale materials are being extensively investigated for applications in biology and medicine and are ready to make significant contributions in the realization of exciting advancements in diverse areas of diagnostics and therapeutics. Aiming for more accurate, efficient, non-invasive and fast diagnostic tools, the use of near-infrared (NIR) light in the range of the 1st and 2nd biological window (NIR-I: 0.70-0.95 µm; NIR-II: 1.00-1.35 µm) provides deeper penetration depth into biological tissue, better image contrast, reduced phototoxicity and photobleaching. Consequently, NIR-based bioimaging became a quickly emerging field and manifold new NIR-emitting bioprobes have been reported. Since commercially available microscopes are not optimized for this kind of NPs, a new microscopy hyperspectral confocal imager has been developed to cover a broad spectral range (400 to 1700 nm) with high spectral resolution. The smallest spectral variation can be easily monitored thanks to the high spectral resolution (as low as 0.2 nm). This is possible thanks to a combination of an EMCCD and an InGaAs camera with a high resolution spectrometer. An extended number of NPs can be excited with a Ti:Sapphire laser, which provides tunable illumination within 690-1040 nm. Cells and tissues can be mapped in less than 100 ms, allowing in-vivo imaging. As a proof of concept, here we present the preliminary results of the spatial distribution of the fluorescence signal intensity from lanthanide doped nanoparticles incorporated into a system of biological interest. The temperature sub-mm gradient - analyzing the spectral features so gathered through an all-optical route is also thoroughly discussed.

  20. [Influence of human body target's spectral characteristics on visual range of low light level image intensifiers].

    Science.gov (United States)

    Zhang, Jun-Ju; Yang, Wen-Bin; Xu, Hui; Liu, Lei; Tao, Yuan-Yaun

    2013-11-01

    To study the effect of different human target's spectral reflective characteristic on low light level (LLL) image intensifier's distance, based on the spectral characteristics of the night-sky radiation and the spectral reflective coefficients of common clothes, we established a equation of human body target's spectral reflective distribution, and analyzed the spectral reflective characteristics of different human targets wearing the clothes of different color and different material, and from the actual detection equation of LLL image intensifier distance, discussed the detection capability of LLL image intensifier for different human target. The study shows that the effect of different human target's spectral reflective characteristic on LLL image intensifier distance is mainly reflected in the average reflectivity rho(-) and the initial contrast of the target and the background C0. Reflective coefficient and spectral reflection intensity of cotton clothes are higher than polyester clothes, and detection capability of LLL image intensifier is stronger for the human target wearing cotton clothes. Experimental results show that the LLL image intensifiers have longer visual ranges for targets who wear cotton clothes than targets who wear same color but polyester clothes, and have longer visual ranges for targets who wear light-colored clothes than targets who wear dark-colored clothes. And in the full moon illumination conditions, LLL image intensifiers are more sensitive to the clothes' material.

  1. Dynamic Range Adaptation to Spectral Stimulus Statistics in Human Auditory Cortex

    Science.gov (United States)

    Schlichting, Nadine; Obleser, Jonas

    2014-01-01

    Classically, neural adaptation refers to a reduction in response magnitude by sustained stimulation. In human electroencephalography (EEG), neural adaptation has been measured, for example, as frequency-specific response decrease by previous stimulation. Only recently and mainly based on animal studies, it has been suggested that statistical properties in the stimulation lead to adjustments of neural sensitivity and affect neural response adaptation. However, it is thus far unresolved which statistical parameters in the acoustic stimulation spectrum affect frequency-specific neural adaptation, and on which time scales the effects take place. The present human EEG study investigated the potential influence of the overall spectral range as well as the spectral spacing of the acoustic stimulation spectrum on frequency-specific neural adaptation. Tones randomly varying in frequency were presented passively and computational modeling of frequency-specific neural adaptation was used. Frequency-specific adaptation was observed for all presentation conditions. Critically, however, the spread of adaptation (i.e., degree of coadaptation) in tonotopically organized regions of auditory cortex changed with the spectral range of the acoustic stimulation. In contrast, spectral spacing did not affect the spread of frequency-specific adaptation. Therefore, changes in neural sensitivity in auditory cortex are directly coupled to the overall spectral range of the acoustic stimulation, which suggests that neural adjustments to spectral stimulus statistics occur over a time scale of multiple seconds. PMID:24381293

  2. Retrieving Soil Hydraulic Properties by Diffuse Spectral Reflectance Data in Vis-NIR-SWIR Range

    Science.gov (United States)

    Babaeian, E.; Homaee, M.; Vereecken, H.; Montzka, C.; Norouzi, A. A.; Van Genuchten, M.

    2014-12-01

    Information about the soil water characteristics is necessary for modeling water flow and solute transport processes in vadose zone. Soil spectroscopy in the visible, near-infrared and shortwave infrared (Vis-NIR-SWIR) range has been widely used as a rapid, cost-effective and non-destructive technique to predict basic soil properties. In this paper we used three different approaches to retrieve soil hydraulic parameters from spectral data in the visible, near-infrared and shortwave-infrared (Vis-NIR-SWIR) region and basic soil properties. Using stepwise multiple linear statistics coupled with bootstrapping, we derived and validated three types of point and parametric transfer functions: i) spectral transfer functions (STFs), ii) pedotransfer functions (PTFs) and iii) spectral pedotransfer functions (SPTFs) which respectively used spectral data, basic soil properties and spectral based basic soil predictions as their inputs. We further evaluated a direct fit of the van Genuchten (VG) and Brooks-Corey (BC) retention models to the predicted water contents obtained with each approach. According to the results, soil water contents, the VG and BC parameters as well as basic soil properties showed significant (pwater contents in the mid and dry parts of retention curve. In the wet range, PTFs were found to perform better than the other two approaches. Compared to the STFs, however, better water content estimates were obtained using the SPTFs in the wet range. The parametric STFs and SPTFs of both the VG and BC models developed from spectral data performed slightly better than parametric PTFs for the retention curve. The best predictions were obtained with a direct fit of the retention models to soil water contents estimated with point transfer functions. Our findings suggest that spectral information, as a promising approach, may be used to accurately predict soil water contents, and indirectly the water retention curve. Using spectral data as an input of PTFs provides an

  3. Dispersion model for optical thin films applicable in wide spectral range

    Science.gov (United States)

    Franta, Daniel; Nečas, David; Ohlídal, Ivan; Giglia, Angelo

    2015-09-01

    In the optics industry thin film systems are used to construct various interference devices such as antireflective coatings, high-reflectance mirrors, beam splitters and filters. The optical characterization of complex optical systems can not be performed by measurements only in the short spectral range in which the interference devices will be employed because the measured data do not contain sufficient information about all relevant parameters of these systems. The characterization of film materials requires the extension of the spectral range of the measurements to the IR region containing phonon absorption and to the UV region containing the electronic excitations. However, this leads to necessity of a dispersion model suitable for the description of the dielectric response in the wide spectral range. Such model must respect the physical conditions following from theory of dispersion, particularly Kramers-Kronig relations and integrability imposed by sum rules. This work presents the construction of a universal dispersion model composed from individual contributions representing both electronic and phonon excitations. The efficiency of presented model is given by the fact that all the contributions are described by analytical expressions. It is shown that the model is suitable for precise modeling of spectral dependencies of optical constants of a broad class of materials used in the optical industry for thin film systems such as MgF2, SiO2, Al2O3, HfO2, Ta2O5 and TiO2 in the spectral range from far IR to vacuum UV.

  4. High Dynamic Range Spectral Analysis in the kHz Band

    CERN Document Server

    Boccardi, A

    2009-01-01

    Many beam instrumentation signals of large circular accelerators are in the kHz range and can thus be digitised with powerful high resolution ADCs. A particularly large dynamic range can be achieved if the signals are analysed in the frequency domain. This report presents a system employing audio ADCs and FPGA-based spectral analysis, initially developed for tune measurement applications. Technical choices allowing frequency domain dynamic ranges beyond 140 dB are summarised.

  5. High-q microring resonator with narrow free spectral range for pulse repetition rate multiplication

    DEFF Research Database (Denmark)

    Pu, Minhao; Ji, Hua; Frandsen, Lars Hagedorn

    2009-01-01

    We demonstrate a silicon-on-insulator microring resonator with a free-spectral-range of 0.32 nm, an extinction ratio of 27 dB, and a quality factor of ~140900 at 1550 nm that is used for pulse repetition-rate multiplication from 10 to 40 GHz.......We demonstrate a silicon-on-insulator microring resonator with a free-spectral-range of 0.32 nm, an extinction ratio of 27 dB, and a quality factor of ~140900 at 1550 nm that is used for pulse repetition-rate multiplication from 10 to 40 GHz....

  6. Light field camera as a Fourier transform spectrometer sensor: instrument characterization and passive spectral ranging.

    Science.gov (United States)

    Côté, Alex; Levasseur, Simon; Boudreau, Sylvain; Genest, Jérôme

    2014-07-01

    This paper presents a concept using field cameras in combination with Fourier transform spectrometers. The device can produce five-dimensional (position-angle-spectra) data cubes. This can lead to accurate measurements in both spectrum and distance and allows a thorough characterization of the interferometer, as well as adds passive ranging information to hyperspectral images. Shear and tilt fringes are simultaneously observed in a fixed optical path difference interferometer, and a passive spectral ranging demonstration is done in both absorption and emission for the 500-900 nm spectral bands.

  7. Multi-Nucleon Short-Range Correlation Model for Nuclear Spectral Functions: I. Theoretical Framework

    CERN Document Server

    Artiles, Oswaldo

    2016-01-01

    We develop a theoretical approach for nuclear spectral functions at high missing momenta and removal energy based on the multi-nucleon short-range correlation~(SRC) model. The approach is based on the effective Feynman diagrammatic method which allows to account for the relativistic effects important in the SRC domain. In addition to two-nucleon SRC with center of mass motion we derived also the contribution of three-nucleon SRCs to the nuclear spectral functions. The latter is modeled based on the assumption that 3N SRCs are a product of two sequential short range NN interactions. This approach allowed us to express the 3N SRC part of the nuclear spectral function as a convolution of two NN SRCs. Thus the knowledge of 2N SRCs allows us to model both two- and three-nucleon SRC contribution to the spectral function. The derivations of the spectral functions are based on the two theoretical frameworks in evaluating covariant Feynman diagrams: In the first, referred as virtual nucleon approximation, we reduce Fe...

  8. Multinucleon short-range correlation model for nuclear spectral functions: Theoretical framework

    Science.gov (United States)

    Artiles, Oswaldo; Sargsian, Misak M.

    2016-12-01

    We develop a theoretical approach for nuclear spectral functions at high missing momenta and removal energies based on the multinucleon short-range correlation (SRC) model. The approach is based on the effective Feynman diagrammatic method which allows us to account for the relativistic effects important in the SRC domain. In addition to two-nucleon (2N) SRC with center of mass motion we also derive the contribution of three-nucleon SRCs to the nuclear spectral functions. The latter is modeled based on the assumption that 3N SRCs are a product of two sequential short-range nucleon-nucleon (NN) interactions. This approach allows us to express the 3N SRC part of the nuclear spectral function as a convolution of two NN SRCs. Thus the knowledge of 2N SRCs allows us to model both two- and three-nucleon SRC contributions to the spectral function. The derivations of the spectral functions are based on two theoretical frameworks for evaluating covariant Feynman diagrams: In the first, referred to as virtual nucleon approximation, we reduce Feynman diagrams to the time ordered noncovariant diagrams by evaluating nucleon spectators in the SRC at their positive energy poles, neglecting explicitly the contribution from vacuum diagrams. In the second approach, referred to as light-front approximation, we formulate the boost invariant nuclear spectral function in the light-front reference frame in which case the vacuum diagrams are generally suppressed and the bound nucleon is described by its light-front variables such as momentum fraction, transverse momentum, and invariant mass.

  9. Multi-Nucleon Short-Range Correlation Model for Nuclear Spectral Functions.

    Science.gov (United States)

    Artiles, Oswaldo; Sargsian, Misak

    2017-01-01

    We develop a theoretical model for nuclear spectral functions at high missing momenta and energies based on the multi-nucleon short-range correlation (SRC) model aimed at probing nuclear structure at short-distances. The model is based on the effective Feynman diagram method which allows us to account for the relativistic effects in the SRC domain. We derive the contribution of two-nucleon SRC with center of mass motion, and three-nucleon SRCs to the nuclear spectral functions. The spectral functions are based on two theoretical approaches in evaluating covariant Feynman diagrams: In the first, referred to as virtual nucleon approximation, we reduce Feynman diagrams to the time ordered non-covariant diagrams by evaluating nucleon spectators on the SRC at their positive energy poles, neglecting the contribution from vacuum diagrams. In the second approach, referred to as light-front approximation, we formulate the boost invariant nuclear spectral function on the light-front reference frame, on which the vacuum diagrams are suppressed. Numerical calculations and parametrization of spectral functions and momentum distributions are presented. This work is supported by U.S. Department of Energy grant under contract DE- FG02-01ER41172.

  10. Integration of Absorption Feature Information from Visible to Longwave Infrared Spectral Ranges for Mineral Mapping

    Directory of Open Access Journals (Sweden)

    Veronika Kopačková

    2017-09-01

    Full Text Available Merging hyperspectral data from optical and thermal ranges allows a wider variety of minerals to be mapped and thus allows lithology to be mapped in a more complex way. In contrast, in most of the studies that have taken advantage of the data from the visible (VIS, near-infrared (NIR, shortwave infrared (SWIR and longwave infrared (LWIR spectral ranges, these different spectral ranges were analysed and interpreted separately. This limits the complexity of the final interpretation. In this study a presentation is made of how multiple absorption features, which are directly linked to the mineral composition and are present throughout the VIS, NIR, SWIR and LWIR ranges, can be automatically derived and, moreover, how these new datasets can be successfully used for mineral/lithology mapping. The biggest advantage of this approach is that it overcomes the issue of prior definition of endmembers, which is a requested routine employed in all widely used spectral mapping techniques. In this study, two different airborne image datasets were analysed, HyMap (VIS/NIR/SWIR image data and Airborne Hyperspectral Scanner (AHS, LWIR image data. Both datasets were acquired over the Sokolov lignite open-cast mines in the Czech Republic. It is further demonstrated that even in this case, when the absorption feature information derived from multispectral LWIR data is integrated with the absorption feature information derived from hyperspectral VIS/NIR/SWIR data, an important improvement in terms of more complex mineral mapping is achieved.

  11. Materials Pushing the Application Limits of Wire Grid Polarizers further into the Deep Ultraviolet Spectral Range

    CERN Document Server

    Siefke, Thomas; Pfeiffer, Kristin; Puffky, Oliver; Dietrich, Kay; Franta, Daniel; Ohlídal, Ivan; Szeghalmi, Adriana; Kley, Ernst-Bernhard; Tünnermann, Andreas

    2016-01-01

    Wire grid polarizers (WGPs), periodic nano-optical meta-surfaces, are convenient polarizing elements for many optical applications. However, they are still inadequate in the deep ultraviolet spectral range. We show that to achieve high performance ultraviolet WGPs a material with large absolute value of the complex permittivity and extinction coefficient at the wavelength of interest has to be utilized. This requirement is compared to refractive index models considering intraband and interband absorption processes. We elucidate why the extinction ratio of metallic WGPs intrinsically humble in the deep ultraviolet, whereas wide bandgap semiconductors are superior material candidates in this spectral range. To demonstrate this, we present the design, fabrication and optical characterization of a titanium dioxide WGP. At a wavelength of 193 nm an unprecedented extinction ratio of 384 and a transmittance of 10 % is achieved.

  12. Semiconductor lasers with a continuous tuning range above 100 nm in the nearest IR spectral region

    Energy Technology Data Exchange (ETDEWEB)

    Kostin, Yu O; Lobintsov, A A; Shramenko, M V [OOO ' Opton' , Moscow (Russian Federation); Ladugin, M A; Marmalyuk, A A [Open Joint-Stock Company M.F. Stel' makh Polyus Research Institute, Moscow (Russian Federation); Chamorovsky, A Yu [Superlum Ltd., Unit B3, Fota Point Enterprise Park, Carrigtwohill, Co Cork (Ireland); Yakubovich, S D [Moscow State Institute of Radio-Engineering, Electronics and Automation (Technical University), Moscow (Russian Federation)

    2015-08-31

    We have developed two new types of lasers based on quantum-confined semiconductor optical amplifiers with an acousto-optic tunable filter in an external fibre ring cavity. The lasers offer continuous wavelength tuning ranges from 780 to 885 and from 880 to 1010 nm, 20 mW of cw output power, and a tuning rate up to 10{sup 4} nm s{sup -1} at an instantaneous spectral linewidth less than 0.1 nm. (lasers)

  13. Spectral characteristics of nanometer-thick chromium films in terahertz frequency range

    Science.gov (United States)

    Andreev, V. G.; Angeluts, A. A.; Vdovin, V. A.; Lukichev, V. F.

    2015-02-01

    The spectral characteristics (reflection, transmission, and absorption coefficients) of thin chromium films on silica substrates have been measured using a pulsed source of terahertz radiation. The spectra of optical coefficients were obtained in a frequency range of 0.25-1.1 THz. Dependences of the optical coefficients on the metal film thickness at 1 THz were constructed. The maximum absorption coefficient (43%) was observed at a film thickness of 10 nm.

  14. Influence of spectral resolution, spectral range and signal-to-noise ratio of Fourier transform infra-red spectra on identification of high explosive substances.

    Science.gov (United States)

    Banas, Krzysztof; Banas, Agnieszka M; Heussler, Sascha P; Breese, Mark B H

    2018-01-05

    In the contemporary spectroscopy there is a trend to record spectra with the highest possible spectral resolution. This is clearly justified if the spectral features in the spectrum are very narrow (for example infra-red spectra of gas samples). However there is a plethora of samples (in the liquid and especially in the solid form) where there is a natural spectral peak broadening due to collisions and proximity predominately. Additionally there is a number of portable devices (spectrometers) with inherently restricted spectral resolution, spectral range or both, which are extremely useful in some field applications (archaeology, agriculture, food industry, cultural heritage, forensic science). In this paper the investigation of the influence of spectral resolution, spectral range and signal-to-noise ratio on the identification of high explosive substances by applying multivariate statistical methods on the Fourier transform infra-red spectral data sets is studied. All mathematical procedures on spectral data for dimension reduction, clustering and validation were implemented within R open source environment. Copyright © 2017 Elsevier B.V. All rights reserved.

  15. Spectral Range Optimization to Enhance the Effectiveness of Phototherapy for Neonatal Hyperbilirubinemia

    Science.gov (United States)

    Plavskii, V. Yu.; Mikulich, A. V.; Leusenko, I. A.; Tretyakova, A. I.; Plavskaya, L. G.; Serdyuchenko, N. S.; Gao, J.; Xiong, D.; Wu, X.

    2017-03-01

    The effectiveness of phototherapy for hyperbilirubinemia of newborns using narrowband LED sources was found to depend not only on the position of the LED emission spectrum peak within the absorption band of bilirubin but also on the width of the incident radiation spectrum. Extension of the spectral range of radiation by adding a green component with λmax ≈ 505 nm to the blue light band with λmax ≈ 462 nm (provided equal integrated power density) gives a more efficient decrease in the total bilirubin level in the blood of newborns. This effect was attributed to heterogeneity of the spectral characteristics of bilirubin in different microenvironments as well as dependence of the optimal wavelength for photoisomerization of the pigment on the depth of the blood vessels where the bilirubin phototransformation reactions occur. Moreover, extension of the spectral range of the incident radiation by adding a green component increases the irradiated volumes of blood where the photoisomerization reactions with a high lumirubin quantum yield underlying this phototherapy are initiated.

  16. Extending the Effective Ranging Depth of Spectral Domain Optical Coherence Tomography by Spatial Frequency Domain Multiplexing

    Directory of Open Access Journals (Sweden)

    Tong Wu

    2016-11-01

    Full Text Available We present a spatial frequency domain multiplexing method for extending the imaging depth range of a spectral domain optical coherence tomography (SDOCT system without any expensive device. This method uses two galvo scanners with different pivot-offset distances in two independent reference arms for spatial frequency modulation and multiplexing. The spatial frequency contents corresponding to different depth regions of the sample can be shifted to different frequency bands. The spatial frequency domain multiplexing SDOCT system provides an approximately 1.9-fold increase in the effective ranging depth compared with that of a conventional full-range SDOCT system. The reconstructed images of phantom and biological tissue demonstrate the expected increase in ranging depth. The parameters choice criterion for this method is discussed.

  17. Silicon photonics athermal Mach-Zehnder interferometer with wide thermal and spectral operating range

    Science.gov (United States)

    Xing, Peng; Viegas, Jaime

    2015-02-01

    In the context of 3D-integrated circuit (3DIC) integration of photonic and electronic components on vertical stacks covering different domains (digital, analog, RF, optical and MEMS), the control and minimization of adverse thermal effects on the behavior of the different parts of the microsystem is a major concern. Solutions based on passive athermal design are good candidates for enabling operation of optical components over electronic ICs with variable temporal and spatial thermal load while at the same time, minimizing energy loss on thermal biasing resistive loads. In this work, an improved athermal design method and the corresponding validating fabricated prototype are presented with the aim of extending the spectral athermal operating range of a Mach-Zehnder interferometer (MZI) over a wide thermal range with minimal temperature sensitivity. The proposed approach is demonstrated with a CMOS compatible silicon-on-insulator process flow fabrication run. The fabricated MZIs have a temperature sensitivity of around 20 pm/K over a spectral range larger than 60 nm for operating temperatures in the range of 20°C to 60°C. These devices are suitable for future optical and electronic 3D IC integration.

  18. Statistical Analysis of Partial Discharges in SF6 Gas via Optical Detection in Various Spectral Ranges

    Directory of Open Access Journals (Sweden)

    Ming Ren

    2016-03-01

    Full Text Available Partial discharge (PD detection is essential to the operation of high-voltage systems. In this context, we investigate the basic characteristics of light emission during PDs in SF6 gas from the perspective of insulation diagnosis. A synchronous system is constructed using three optical photoelectric instruments with separate wavelength responses in the ultraviolet (UV, 189–352 nm, visible (VIS, 381–675 nm, and near-infrared (NIR, 737–920 nm spectral ranges and a wide-band PD current pulse detector with a response of 1 pC. The results indicate that light emission depends upon the type of insulation defect and discharge energy. An increase in PD charge gives rise to more components in the spectral range from UV to VIS, and the presence of an insulator surface in discharges yields a more complex VIS-to-NIR spectrum. The phase-resolved partial discharge pattern (PRPD of UV light pulses can reasonably reflect the electroluminescence process in the presence of the insulator surface and weak corona at negative voltage points. The PRPD of VIS light describes the features of the actual PD pattern in most cases. In comparison with the other two spectral ranges, light intensity in the VIS range is more sensitive to changes in gas-pressure-normalized voltage (Vrms/p. The linear fitting analysis of the relationships between the light intensity and PD charge shows that UV light detection has a greater sensitivity to the PD charge and that UV detection exhibits a greater degree of linearity. NIR detection is applicable only to severe PDs. We believe that our findings can significantly aid in application of optical PD diagnosis in SF6 gas insulated systems.

  19. Adaptive uniform grayscale coded aperture design for high dynamic range compressive spectral imaging

    Science.gov (United States)

    Diaz, Nelson; Rueda, Hoover; Arguello, Henry

    2016-05-01

    Imaging spectroscopy is an important area with many applications in surveillance, agriculture and medicine. The disadvantage of conventional spectroscopy techniques is that they collect the whole datacube. In contrast, compressive spectral imaging systems capture snapshot compressive projections, which are the input of reconstruction algorithms to yield the underlying datacube. Common compressive spectral imagers use coded apertures to perform the coded projections. The coded apertures are the key elements in these imagers since they define the sensing matrix of the system. The proper design of the coded aperture entries leads to a good quality in the reconstruction. In addition, the compressive measurements are prone to saturation due to the limited dynamic range of the sensor, hence the design of coded apertures must consider saturation. The saturation errors in compressive measurements are unbounded and compressive sensing recovery algorithms only provide solutions for bounded noise or bounded with high probability. In this paper it is proposed the design of uniform adaptive grayscale coded apertures (UAGCA) to improve the dynamic range of the estimated spectral images by reducing the saturation levels. The saturation is attenuated between snapshots using an adaptive filter which updates the entries of the grayscale coded aperture based on the previous snapshots. The coded apertures are optimized in terms of transmittance and number of grayscale levels. The advantage of the proposed method is the efficient use of the dynamic range of the image sensor. Extensive simulations show improvements in the image reconstruction of the proposed method compared with grayscale coded apertures (UGCA) and adaptive block-unblock coded apertures (ABCA) in up to 10 dB.

  20. Comparison of Free Spectral Range and Quality Factor for Two-Dimensional Square and Circular Microcavities

    Institute of Scientific and Technical Information of China (English)

    国伟华; 黄永箴; 陆巧银; 于丽娟

    2004-01-01

    Free spectral range of whispering-gallery (WG)-like modes in a two-dimensional (2D) square microcavity is found to be twice that in a 2D circular microcavity. The quality factor of the WG-like mode with the low mode number in a 2D square microcavity, calculated by the finite-difference time-domain (FDTD) technique and the Pade approximation method, is found to exceed that of the WG mode in 2D circular microcavity with the same cavity dimension and close mode wavelength.

  1. Calibrating image plate sensitivity in the 700 to 5000 eV spectral energy range

    Science.gov (United States)

    Haugh, Michael J.; Lee, Joshua; Romano, Edward; Schneider, Marilyn

    2013-09-01

    This paper describes a method to calibrate image plate sensitivity for use in the low energy spectral range. Image plates, also known as photostimulable luminescence (PSL) detectors, have often proved to be a valuable tool as a detector for plasma physics studies. Their advantages of large dynamic range, high stopping power, and resistance to neutron damage sometimes outweigh the problems of limited resolution and the remote processing required. The neutron damage resistance is required when the X-ray source is producing a high neutron flux. The Static X-ray Imager (SXI) is a key diagnostic on the National Ignition Facility (NIF) target chamber at LLNL for use in determining the symmetry of the laser beams. The SXI is essential to proper interpretation of the data from the Dante diagnostic to determine the X-ray radiation temperature. It is comprised of two diagnostics located at the top and the bottom of the target chamber. The usual detector is a large array CCD camera. For shots giving high yields of neutrons, the camera would not only be blinded by the neutrons, it would be damaged. To get around this problem, an image plate (IP) is used as the detector. The NIF application covers the energy range from 700 to 5000 eV. The type of image plates typically used for plasma physics are the Fuji BAS-MS, BAS-SR, and BAS-TR models. All models consist of an X-ray sensitive material made of BaF(Br,I):Eu2+ embedded in a plastic binder. X-rays incident on the phosphor ionize the Eu 2+ producing Eu3+ and free electrons that are trapped in lattice defects (F-centers) produced by the absence of halogen ions in the BaF2 crystal. An image plate readout scanner irradiates the IP with a red laser causing reduction of the Eu3+ and emission of a blue photon. The photon is collected using a photomultiplier and digitized to make an electronic image. Image plates are cleared of all F-centers by putting them under a bright light for about 10 minutes. They are then ready for producing a

  2. Extension of spectral range of Peltier cooled photodetectors to 16 μm

    Science.gov (United States)

    Piotrowski, A.; Piotrowski, J.; Gawron, W.; Pawluczyk, J.; Pedzinska, M.

    2009-05-01

    We have developed various types of photodetectors operating without cryocooling. Initially, the devices were mostly used for uncooled detection of CO2 laser radiation. Over the years the performance and speed of response has been steadily improved. At present the uncooled or Peltier cooled photodetectors can be used for sensitive and fast response detection in the MWIR and LWIR spectral range. The devices have found important applications in IR spectrometry, quantum cascade laser based gas analyzers, laser radiation alerters and many other IR systems. Recent efforts were concentrated on the extension of useful spectral range to >13 μm, as required for its application in FTIR spectrometers. This was achieved with improved design of the active elements, use of monolithic optical immersion technology, enhanced absorption of radiation, dedicated electronics, series connection of small cells in series, and last but not least, applying more efficient Peltier coolers. Practical devices are based on the complex HgCdTe heterostructures grown on GaAs substrates with MOCVD technique with immersion lens formed by micromachining in the GaAs substrates. The results are very encouraging. The devices cooled with miniature 4 stage Peltier coolers mounted in TO-8 style housings show significant response at wavelength exceeding 16 μm.

  3. Military reconnaissance platform for the spectral range from the visible to the MWIR

    Science.gov (United States)

    Gerken, M.; Fritze, J.; Münzberg, M.; Weispfenning, M.

    2017-02-01

    The reconnaissance capability of a military observation and targeting platform is mainly driven by the performance of the used sensors. In general, the MWIR thermal imager is the primary sensor and the use of a visible camera increases the identification capability of the platform during day for very long observation ranges. In addition to the imaging sensors a laser pointer, a laser rangefinder (LRF), and a combined laser rangefinder/ designator (LRF/D) completes the sensor suite. As LRF a single pulse eye safe rangefinder based on an OPO shifted Nd:YAG transmitter can be used. The alternative LRF/D uses an diode laser pumped dual wavelength OPO/Nd:YAG transmitter and can be operated either at 1570 nm or at 1064 nm with a pulse rate of maximum 25 pps [1]. A MWIR thermal imager [2] with a 1280x1024 MWIR detector and an optical zoom range between 1.2° and 20° horizontal fields of view provides a HD-SDI video stream in the 720p or 1080p standard. A camera build in software image stabilizer and a smart tone mapping algorithm improves the reconnaissance results for the observer. A combined camera covers the visible, NIR and SWIR spectral range [3] using a common entrance optics. The resolution of the color camera Si-CMOS chip is 1920x1080 and of the InGaAs focal plane array it is 640x512 detector pixel. The combined VIS/NIR/SWIR camera provides improved ranging under hazy and misty atmospheric conditions and also improved detection of laser spots e.g. of the integrated laser designator with high sensitivity in the spectral range between 450 nm up to 1700 nm, most of the military lasers are operating in the NIR and SWIR spectral band [3]. The combination of the sensors in the platform improves significantly the operational use. The application of the described platform is not limited to military scout vehicles, the available sensors are also integrated in a targeting platform with similar performances but other environmental demands. The possibilities, improvements in

  4. Broadband semiconductor optical amplifiers of the spectral range 750 – 1100 nm

    Energy Technology Data Exchange (ETDEWEB)

    Andreeva, E V; Il' chenko, S N; Lobintsov, A A; Shramenko, M V [Superlum Diodes Ltd., Moscow (Russian Federation); Ladugin, M A [' Sigm Plyus' Ltd, Moscow (Russian Federation); Marmalyuk, A A [Open Joint-Stock Company M.F. Stel' makh Polyus Research Institute, Moscow (Russian Federation); Yakubovich, S D [Moscow State Institute of Radio-Engineering, Electronics and Automation (Technical University), Moscow (Russian Federation)

    2013-11-30

    A line of travelling-wave semiconductor optical amplifiers (SOAs) based on heterostructures used for production of broadband superluminescent diodes is developed. The pure small-signal gains of the developed SOA modules are about 25 dB, while the gain bandwidths at a level of –10 dB reach 50 – 100 nm. As a whole, the SOA modules cover the IR spectral range from 750 to 1100 nm. The SOAs demonstrate a high reliability at a single-mode fibre-coupled cw output power up to 50 mW. Examples of application of two of the developed SOA modules as active elements of broadband fast-tunable lasers are presented. (lasers)

  5. Circuit model optimization of a nano split ring resonator dimer antenna operating in infrared spectral range

    Energy Technology Data Exchange (ETDEWEB)

    Gneiding, N., E-mail: Natalia.Gneiding@physik.uni-erlangen.de [Erlangen Graduate School in Advanced Optical Technologies (SAOT), University of Erlangen-Nuremberg, 91052 Erlangen (Germany); Zhuromskyy, O.; Peschel, U. [Institute of Optics, Information and Photonics, University of Erlangen-Nuremberg, 91058 Erlangen (Germany); Shamonina, E. [Department of Engineering Science, University of Oxford, Parks Road, OX1 3PJ Oxford (United Kingdom)

    2014-10-28

    Metamaterials are comprised of metallic structures with a strong response to incident electromagnetic radiation, like, for example, split ring resonators. The interaction of resonator ensembles with electromagnetic waves can be simulated with finite difference or finite elements algorithms, however, above a certain ensemble size simulations become inadmissibly time or memory consuming. Alternatively a circuit description of metamaterials, a well developed modelling tool at radio and microwave frequencies, allows to significantly increase the simulated ensemble size. This approach can be extended to the IR spectral range with an appropriate set of circuit element parameters accounting for physical effects such as electron inertia and finite conductivity. The model is verified by comparing the coupling coefficients with the ones obtained from the full wave numerical simulations, and used to optimize the nano-antenna design with improved radiation characteristics.

  6. Broadband semiconductor optical amplifiers of the spectral range 750 - 1100 nm

    Science.gov (United States)

    Andreeva, E. V.; Il'chenko, S. N.; Ladugin, M. A.; Lobintsov, A. A.; Marmalyuk, A. A.; Shramenko, M. V.; Yakubovich, S. D.

    2013-11-01

    A line of travelling-wave semiconductor optical amplifiers (SOAs) based on heterostructures used for production of broadband superluminescent diodes is developed. The pure small-signal gains of the developed SOA modules are about 25 dB, while the gain bandwidths at a level of -10 dB reach 50 - 100 nm. As a whole, the SOA modules cover the IR spectral range from 750 to 1100 nm. The SOAs demonstrate a high reliability at a single-mode fibre-coupled cw output power up to 50 mW. Examples of application of two of the developed SOA modules as active elements of broadband fast-tunable lasers are presented.

  7. A full free spectral range tuning of p-i-n doped Gallium Nitride microdisk cavity

    CERN Document Server

    Niu, Nan; Aharonovich, Igor; Russell, Kasey J; Woolf, Alexander; Sadler, Thomas C; El-Ella, Haitham A R; Kappers, Menno J; Oliver, Rachel A; Hu, Evelyn L

    2012-01-01

    Effective, permanent tuning of the whispering gallery modes (WGMs) of p-i-n doped GaN microdisk cavity with embedded InGaN quantum dots over one free spectral range is successfully demonstrated by irradiating the microdisks with a ultraviolet laser (380nm) in DI water. For incident laser powers between 150 and 960 nW, the tuning rate varies linearly. Etching of the top surface of the cavity is proposed as the driving force for the observed shift in WGMs, and is supported by experiments. The tuning for GaN/InGaN microdisk cavities is an important step for deterministically realizing novel nanophotonic devices for studying cavity quantum electrodynamics.

  8. Collisional Induced Absorption (CIA) bands measured in the IR spectral range .

    Science.gov (United States)

    Stefani, S.; Piccioni, G.; Snels, M.; Adriani, A.; Grassi, D.

    In this work we present two experimental setup able to characterize the optical properties of gases, in particular CO_2 and H_2, at typically planetary conditions. The apparatus consists of a Fourier Transform InfraRed (FT-IT) interferometer able to work in a wide spectral range, from 350 to 25000 cm-1 (0.4 to 29 mu m ) with a relatively high spectral resolution, from 10 to 0.07 cm-1. Two dedicated gas cells have been integrated with the FT-IR. The first, called High Pressure High Temperature (HP-HT), can support pressures up to 300 bar, temperatures up to 300oC and is characterized by an optical path of 2 cm. The second one, a Multi Pass (MP) absorption gas cell, is designed to have a variable optical path, from 2.5 to 30 m, can be heated up to 200o and operate at pressures up to 10 bar. In this paper, measurements of Collision-Induced Absorption (CIA) bands in carbon dioxide and hydrogen recorded in the InfraRed spectral range will be presented. In principle, linear symmetric molecules such as CO_2 and H_2 possess no dipole moment, but, even when the pressure is only a few bar, we have observed the Collisional Induced Absorption (CIA) bands. This absorption results from a short-time collisional interaction between molecules. The band integrated intensity shows a quadratic dependence versus density opposed to the absorption by isolated molecules, which follows Beer's law \\citep{Beer's}. This behaviour suggests an absorption by pairs rather than by individual molecules. The bands integrated intensities show a linear dependence vs square density according to \\citep {CIA Shape} and \\citep{CIA posi}. For what concerns the H_2 CIA bands, a preliminary comparison between simulated data obtained with the model described in \\citep{CIA H2}and measured, shows a good agreement. These processes are very relevant in the dense atmospheres of planets, such as those of Venus and Jupiter and also in extrasolar planets. A detailed knowledge of these contributions is very

  9. Luminescent properties of the ZnSe:Yb crystals in the visible spectral range

    Energy Technology Data Exchange (ETDEWEB)

    Radevici, I., E-mail: ivarad@utu.fi [Wihuri Physical Laboratory, Department of Physics and Astronomy, University of Turku, FI-20014 Turku (Finland); Faculty of Physics and Engineering, Moldova State University, Mateevici str. 60, MD-2009, Chisinau, Republic of Moldova (Moldova, Republic of); Sushkevich, K. [Faculty of Physics and Engineering, Moldova State University, Mateevici str. 60, MD-2009, Chisinau, Republic of Moldova (Moldova, Republic of); Sirkeli, V. [Wihuri Physical Laboratory, Department of Physics and Astronomy, University of Turku, FI-20014 Turku (Finland); Faculty of Physics and Engineering, Moldova State University, Mateevici str. 60, MD-2009, Chisinau, Republic of Moldova (Moldova, Republic of); Huhtinen, H. [Wihuri Physical Laboratory, Department of Physics and Astronomy, University of Turku, FI-20014 Turku (Finland); Nedeoglo, D. [Faculty of Physics and Engineering, Moldova State University, Mateevici str. 60, MD-2009, Chisinau, Republic of Moldova (Moldova, Republic of); Paturi, P. [Wihuri Physical Laboratory, Department of Physics and Astronomy, University of Turku, FI-20014 Turku (Finland)

    2013-11-15

    Luminescent properties of the ytterbium doped zinc selenide crystals with various concentrations of the doping impurity in 0.03–8 at % range within the temperature interval from 6 K to 300 K were studied. It was shown that ytterbium does not form any proper photoluminescence (PL) bands in the visible spectral range, but it has significant influence on the crystals luminescent properties by changing their defect composition. An attempt to determine ytterbium ion surroundings in the crystal lattice was made based on the obtained experimental results. An assumption about simultaneous compensation of donor and acceptor defects as a result of doping annealing in Zn+X at % Yb melt was made. -- Highlights: • ZnSe:Yb crystals with Yb concentration within 0.03–8 at% range were obtained • Temperature and concentration dependences of ZnSe:Yb PL properties were studied • Ytterbium impurity contribution to formation of the PL bans was determined • A model explaining Yb interaction with native and extrinsic defects was proposed.

  10. MMI-based MOEMS FT spectrometer for visible and IR spectral ranges

    Science.gov (United States)

    Al-Demerdash, Bassem M.; Medhat, Mostafa; Sabry, Yasser M.; Saadany, Bassam; Khalil, Diaa

    2014-03-01

    MEMS spectrometers have very strong potential in future healthcare and environmental monitoring applications, where Michelson interferometers are the core optical engine. Recently, MEMS Michelson interferometers based on using silicon interface as a beam splitter (BS) has been proposed [7, 8]. This allows having a monolithically-integrated on-chip FTIR spectrometer. However silicon BS exhibits high absorption loss in the visible range and high material dispersion in the near infrared (NIR) range. For this reason, we propose in this work a novel MOEMS interferometer allowing operation over wider spectral range covering both the infrared (IR) and the visible ranges. The proposed architecture is based on spatial splitting and combining of optical beams using the imaging properties of Multi-Mode Interference MMI waveguide. The proposed structure includes an optical splitter for spatial splitting an input beam into two beams and a combiner for spatial combining the two interferometer beams. A MEMS moveable mirror is provided to produce an optical path difference between the two beams. The new interferometer is fabricated using DRIE technology on an SOI wafer. The movable mirror is metalized and attached to a comb-drive actuator fabricated in the same lithography step in a self-aligned manner on chip. The novel interferometer is tested as a Fourier transform spectrometer. Red laser, IR laser and absorption spectra of different materials are measured with a resolution of 2.5 nm at 635-nm wavelength. The structure is a very compact one that allows its integration and fabrication on a large scale with very low cost.

  11. Upgrades to improve the usability, reliability, and spectral range of the MST Thomson scattering diagnostic

    Science.gov (United States)

    Kubala, S. Z.; Borchardt, M. T.; Den Hartog, D. J.; Holly, D. J.; Jacobson, C. M.; Morton, L. A.; Young, W. C.

    2016-11-01

    The Thomson scattering diagnostic on MST records both equilibrium and fluctuating electron temperature with a range capability of 10 eV-5 keV. Standard operation with two modified commercial Nd:YAG lasers allows measurements at rates of 1 kHz-25 kHz. Several subsystems of the diagnostic are being improved. The power supplies for the avalanche photodiode detectors (APDs) that record the scattered light are being replaced to improve usability, reliability, and maintainability. Each of the 144 APDs will have an individual rack mounted switching supply, with bias voltage adjustable to match the APD. Long-wavelength filters (1140 nm center, 80 nm bandwidth) have been added to the polychromators to improve capability to resolve non-Maxwellian distributions and to enable directed electron flow measurements. A supercontinuum (SC) pulsed white light source has replaced the tungsten halogen lamp previously used for spectral calibration of the polychromators. The SC source combines substantial brightness produced in nanosecond pulses with a spectrum that covers the entire range of the polychromators.

  12. High-dynamic range compressive spectral imaging by grayscale coded aperture adaptive filtering

    Directory of Open Access Journals (Sweden)

    Nelson Eduardo Diaz

    2015-12-01

    Full Text Available The coded aperture snapshot spectral imaging system (CASSI is an imaging architecture which senses the three dimensional informa-tion of a scene with two dimensional (2D focal plane array (FPA coded projection measurements. A reconstruction algorithm takes advantage of the compressive measurements sparsity to recover the underlying 3D data cube. Traditionally, CASSI uses block-un-block coded apertures (BCA to spatially modulate the light. In CASSI the quality of the reconstructed images depends on the design of these coded apertures and the FPA dynamic range. This work presents a new CASSI architecture based on grayscaled coded apertu-res (GCA which reduce the FPA saturation and increase the dynamic range of the reconstructed images. The set of GCA is calculated in a real-time adaptive manner exploiting the information from the FPA compressive measurements. Extensive simulations show the attained improvement in the quality of the reconstructed images when GCA are employed.  In addition, a comparison between traditional coded apertures and GCA is realized with respect to noise tolerance.

  13. A wide spectral range single-photon avalanche diode fabricated in an advanced 180 nm CMOS technology

    NARCIS (Netherlands)

    Mandai, S.; Fishburn, M.W.; Maruyama, Y.; Charbon, E.

    2012-01-01

    We present a single-photon avalanche diode (SPAD) with a wide spectral range fabricated in an advanced 180 nm CMOS process. The realized SPAD achieves 20 % photon detection probability (PDP) for wavelengths ranging from 440 nm to 820 nm at an excess bias of 4V, with 30 % PDP at wavelengths from 520

  14. A wide spectral range single-photon avalanche diode fabricated in an advanced 180 nm CMOS technology

    NARCIS (Netherlands)

    Mandai, S.; Fishburn, M.W.; Maruyama, Y.; Charbon, E.

    2012-01-01

    We present a single-photon avalanche diode (SPAD) with a wide spectral range fabricated in an advanced 180 nm CMOS process. The realized SPAD achieves 20 % photon detection probability (PDP) for wavelengths ranging from 440 nm to 820 nm at an excess bias of 4V, with 30 % PDP at wavelengths from 520

  15. Spectral conditions for strong local nondeterminism and exact Hausdorff measure of ranges of Gaussian random fields

    CERN Document Server

    Luan, Nana

    2011-01-01

    Let $X= \\{X(t), t \\in \\R^N\\}$ be a Gaussian random field with values in $\\R^d$ defined by \\[ X(t) = \\big(X_1(t),..., X_d(t)\\big),\\qquad t \\in \\R^N, \\] where $X_1, ..., X_d$ are independent copies of a real-valued, centered, anisotropic Gaussian random field $X_0$ which has stationary increments and the property of strong local nondeterminism. In this paper we determine the exact Hausdorff measure function for the range $X([0, 1]^N)$. We also provide a sufficient condition for a Gaussian random field with stationary increments to be strongly locally nondeterministic. This condition is given in terms of the spectral measures of the Gaussian random fields which may contain either an absolutely continuous or discrete part. This result strengthens and extends significantly the related theorems of Berman (1973, 1988), Pitt (1978) and Xiao (2007, 2009), and will have wider applicability beyond the scope of the present paper.

  16. Group delay dispersion measurements in the mid-infrared spectral range of 2-20 µm.

    Science.gov (United States)

    Habel, Florian; Trubetskov, Michael; Pervak, Vladimir

    2016-07-25

    We present two measurement devices which both allow the direct measurement of the group delay (GD) and group delay dispersion (GDD) of laser optics, covering the near- and mid-infrared (MIR) spectral range from 2 to 20 µm (500-5,000 cm-1). Two different kinds of devices were developed to measure the GDD of multilayer interference coatings. One is a resonant scanning interferometer (RSI) and the other is a white light interferometer (WLI). The WLI is also capable of measuring the GDD in transmission, for instance of bulk material. GDD measurements of a high dispersive mirror for wavelengths from 2.0 to 2.15 µm and one of a multilayer mirror from 8.5 to 12.0 µm are presented. A measurement of a zinc selenide (ZnSe) substrate in transmission was made with the WLI demonstrating the full bandwidth of the device from 1.9 to 20 µm. The comparison of all measurements with their related theoretical values shows a remarkable correspondence.

  17. Effect of spectral range in surface inactivation of Listeria innocua using broad-spectrum pulsed light.

    Science.gov (United States)

    Woodling, Sarah E; Moraru, Carmen I

    2007-04-01

    Pulsed light (PL) treatment is an alternative to traditional thermal treatment that has the potential to achieve several log-cycle reductions in the concentration of microorganisms. One issue that is still debated is related to what specifically causes cell death after PL treatments. The main objective of this work was to elucidate which portions of the PL range are responsible for bacterial inactivation. Stainless steel coupons with controlled surface properties were inoculated with a known concentration of Listeria innocua in the stationary growth phase and treated with 1 to 12 pulses of light at a pulse rate of 3 pulses per s and a pulse width of 360 micros. The effects of the full spectrum (lambda = 180 to 1,100 nm) were compared with the effects obtained when only certain regions of UV, visible, and near-infrared light were used. The effectiveness of the treatments was determined in parallel by the standard plate count and most-probable-number techniques. At a fluence of about 6 J/cm(2), the full-spectrum PL treatment resulted in a 4.08-log reduction of L. innocua on a Mill finish surface, the removal of lambda light resulted in no lethal effects on L. innocua. Overwhelmingly, the portions of the PL spectrum responsible for bacterial death are the UV-B and UV-C spectral ranges (X light (lambda > 400 nm). This work provides additional supporting evidence that cell death in PL treatment is due to exposure to UV light. Additionally, it was shown that even a minor modification of the light path or the UV light spectrum in PL treatments can have a significant negative impact on the treatment intensity and effectiveness.

  18. Highly photoresponsive, ZnO nanorod-based photodetector for operation in the visible spectral range

    Science.gov (United States)

    Choi, Daniel S.; Hansen, Matthew; Van Keuren, Edward; Hahm, Jong-in

    2017-04-01

    While significant advances have been made for gold nanoparticle (AuNP)-coupled zinc oxide (ZnO) as visibly blind, ultraviolet photodetection devices, very few ZnO nanomaterial systems have been developed specifically for use in the visible wavelength regime. Further efforts to develop ZnO-based visible photodetectors (PDs) are still highly warranted in order to better understand the precise effect of AuNP load, operation wavelength, and beam position on the device output. In this study, we demonstrate significantly enhanced, photoresponse behaviors of AuNP-coupled ZnO nanorod (NR) network devices in the visible wavelength range with their photoresponse capacity comparable to, if not far exceeding, most commercial PDs as well as recently reported, visible, AuNP-coupled ZnO detectors. In addition, the nature and degree of the photoresponsivity enhancement are systematically elucidated by investigating their light-triggered electrical signals under varying incident wavelengths, AuNP amounts, and illumination positions. We discuss a possible photoconduction mechanism of our AuNP-coupled ZnO NR PDs and the origins of the high photoresponsivity. Specifically related to the AuNP amount-dependent photoresponse behaviors, the nanoparticle density yielding photoresponse maxima is explained as the interplay between localized surface plasmon resonance, plasmonic heating, and scattering in our photothermoelectric effect-driven device. We show that the AuNP-coupled ZnO NR PDs can be constructed via a straightforward method without the need for ultrahigh vacuum, sputtering procedures, or photo/electron-beam lithographic tools. Hence, the approach demonstrated in this study may serve as a convenient and viable means to advance the current state of ZnO-based PDs for operation in the visible spectral range with greatly increased photoresponsivity.

  19. Spatial distribution of spectral parameters of high latitude geomagnetic disturbances in the Pc5/Pi3 frequency range

    Directory of Open Access Journals (Sweden)

    V. A. Pilipenko

    2010-09-01

    Full Text Available We analyze spectral parameters of the geomagnetic disturbances within the 1–4 mHz (Pc5/Pi3 frequency range for 29 observatories from polar to auroral latitudes. The main object of this study is the broadband (noise background under quiet and moderately disturbed conditions. To obtain a quantitative description of background high-latitude long period ULF activity the log-log dependence of the spectral power on frequency is expanded over Legendre polynomials, and the coefficients of this expansion (spectral moments are used to describe the most common features of these spectra. Not only the spectral power, but also the spectral slope and higher spectral moments, averaged over relatively long time intervals, demonstrate a systematic dependence on corrected geomagnetic (CGM latitude, Φ, and magnetic local time, MLT. The 2-D distributions of the spectral moments in Φ-MLT coordinates are characterized by existence of structures, narrow in latitude and extended in MLT, which can be attributed to the projections of different magnetospheric domains. Spatio-temporal distributions of spectral power of elliptically (P-component and randomly (N-component polarized signal are similar, but not identical. The N-component contribution to the total signal becomes non-negligible in regions with a high local activity, such as the auroral oval and dayside polar cusp. The spectral slope indicates a larger relative contribution of higher frequencies upon the latitude decrease, probably, as a result of the resonant effects in the ULF noise. The higher spectral moments are also controlled mostly by CGM latitude and MLT and are fundamentally different for the polarized and non-polarized components. This study is a step towards the construction of an empirical model of the ULF wave power in Earth's magnetosphere.

  20. Spectral emission properties of a LPP light source in the sub-200nm range for wafer inspection applications

    Science.gov (United States)

    Gambino, Nadia; Rollinger, Bob; Hudgins, Duane; Abhari, Reza; Abreau, F.

    2015-03-01

    In this work, the spectral emission proprieties of a droplet-based laser-produced plasma are investigated in the VUV range. These studies are performed with a spectrograph operating from 30 nm to 180 nm at a spectral resolution of 0.1 nm. The emission spectra are recorded for different droplet-based metal fuels such as tin, indium and gallium in the presence of different background gas pressure levels. The experimental results are relevant for alternative light sources that would be needed for future wafer inspection tools. In addition, the experimental results help to determine the Out- Of-Band (OOB) radiation emission of the EUV source. By tuning the type of fuel, the laser energies and the background gas, the LPP light source shows good capabilities to be operated as a tunable light source that covers a spectral emission range from the EUV to the sub-200 nm range.

  1. Spectral Characteristics of Vegetation Functional Traits across a Range of Thaw Gradients on Alaska's Seward Peninsula

    Science.gov (United States)

    Goswami, S.; Hayes, D. J.; Sloan, V. L.; Liebig, J. A.; Norby, R. J.; Wullschleger, S. D.

    2014-12-01

    The Arctic and Boreal regions are warming rapidly, leading to the thawing of the underlying permafrost and associated changes in vegetation structure and composition. The thawing of ice-rich permafrost drives land surface dynamics called thermokarst, characterized by a variety of geomorphic surface features across high latitude landscapes. The development of these thermokarst or thermo-erosional features depends on factors such as local permafrost conditions, hydrology, geomorphology, vegetation, and climate, but their degree of dependence are not well understood across scales. The structure, functions and traits of the vegetation can work as effective indicators of these landscape changes. Our ability to characterize these vegetation characteristics across a wide range of thaw gradients at the local scale could help us to better understand the dependency as well as the impacts of thermokarst processes on them. This will also help us to develop capabilities to quantify these characteristics and dependencies from local to regional scales by using remote sensing and ecosystem modeling techniques. During the months of June - July of 2013 and 2014, we conducted field surveys at various sites across the central Seward Peninsula in Alaska covering a range of thaw gradients to collect data for vegetation functional traits, ancillary data and also hyperspectral data in the 400-2500 nm range using a field spectrometer. Data were collected from plots established along 50 m transects to capture transitional states of these thaw features from the upland zone, transition zone, and thaw lake basins as well as in polygonal features. Here we discuss the characteristics of vegetation functional traits and how they relate to the ground-based spectral measurements. Some of these findings could be scaled up using airborne and satellite remote sensing data. The findings from this study can improve our understanding of disturbance patterns and their feedbacks to local scale plant and

  2. Characterization of spectral hole depth in Tm3+ :YAG within the cryogenic temperature range

    Institute of Scientific and Technical Information of China (English)

    Chen Lei; Ma Xiu-Rong; Wang Wei; Zhang Shuang-Gen; Mu Kuan-Lin; Wang Xia-Yang; Zhang Shi-Yu

    2013-01-01

    In this paper,spectral hole depth dependence on temperature below 10 K in Tm3+∶YAG crystal is investigated in detail.A novel model is proposed to analyze the temperature dependence on the spectral hole.By using the proposed model,we theoretically deduce the temperature dependence of spectral hole depth.The results are compared with experimental results and they are in good agreement.According to the theoretic results,the optimum temperature in experiment can be found.

  3. Fabry-Perot Based Ranging Interferometer Receiver for High Spectral Resolution Lidar Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Michigan Aerospace Corporation (MAC) is pleased to present the following Phase II proposal for a Fabry-Perot Based Interferometer Receiver for the High Spectral...

  4. The optical properties and spectral features of malignant skin melanocytes in the terahertz frequency range

    Science.gov (United States)

    Goryachuk, A. A.; Begaeva, V. A.; Khodzitsky, M. K.; Truloff, A. S.

    2016-08-01

    The samples of cells of mice's melanocytes have been investigated. Their optical properties and spectral features were investigated by terahertz time-domain spectroscopy (TDS) in transmission mode. It was found that the optical properties of oncological melanocytes and normal cells are different and oncological cells have spectral features of absorption coefficient so it can be concluded that it is easy to discriminate mice's oncological skin melanocytes by using THz TDS.

  5. Development and testing of a fast Fourier transform high dynamic-range spectral diagnostics for millimeter wave characterization

    NARCIS (Netherlands)

    Thoen, D. J.; Bongers, W. A.; Westerhof, E.; Oosterbeek, J. W.; M.R. de Baar,; van den Berg, M. A.; van Beveren, V.; Burger, A.; Goede, A. P. H.; Graswinckel, M. F.; Hennen, B.A.; Schüller, F. C.

    2009-01-01

    A fast Fourier transform (FFT) based wide range millimeter wave diagnostics for spectral characterization of scattered millimeter waves in plasmas has been successfully brought into operation. The scattered millimeter waves are heterodyne downconverted and directly digitized using a fast analog-digi

  6. First observation of SASE radiation using the compact wide-spectral-range XUV spectrometer at FLASH2

    Energy Technology Data Exchange (ETDEWEB)

    Tanikawa, T., E-mail: takanori.tanikawa@desy.de [Deutsches Elektronen-Synchrotron DESY, Notkestrasse 85, 22607 Hamburg (Germany); Hage, A. [Deutsches Elektronen-Synchrotron DESY, Notkestrasse 85, 22607 Hamburg (Germany); School of Mathematics and Physics, Queen' s University Belfast, University Road, Belfast BT7 1NN (United Kingdom); Kuhlmann, M. [Deutsches Elektronen-Synchrotron DESY, Notkestrasse 85, 22607 Hamburg (Germany); Gonschior, J. [Max Planck Research Group for Structural Dynamics, Notkestrasse 85, 22607 Hamburg (Germany); Grunewald, S.; Plönjes, E.; Düsterer, S.; Brenner, G.; Dziarzhytski, S.; Braune, M.; Brachmanski, M. [Deutsches Elektronen-Synchrotron DESY, Notkestrasse 85, 22607 Hamburg (Germany); Yin, Z. [Deutsches Elektronen-Synchrotron DESY, Notkestrasse 85, 22607 Hamburg (Germany); Max Planck Institute for Biophysical Chemistry, Am Fassberg 11, 37077 Göttingen (Germany); Siewert, F. [Helmholtz Zentrum Berlin, Albert-Einstein-Str. 15, 12489 Berlin (Germany); Dzelzainis, T.; Dromey, B. [School of Mathematics and Physics, Queen' s University Belfast, University Road, Belfast BT7 1NN (United Kingdom); Prandolini, M.J. [Helmholtz-Institut Jena, Fröbelstieg 3, 07743 Jena (Germany); Tavella, F. [SLAC National Accelerator Laboratory, 2575 Sand Hill Road, CA 94025 (United States); Zepf, M. [School of Mathematics and Physics, Queen' s University Belfast, University Road, Belfast BT7 1NN (United Kingdom); Helmholtz-Institut Jena, Fröbelstieg 3, 07743 Jena (Germany); Faatz, B. [Deutsches Elektronen-Synchrotron DESY, Notkestrasse 85, 22607 Hamburg (Germany)

    2016-09-11

    The Free-electron LASer in Hamburg (FLASH) has been extended with a new undulator line FLASH2 in 2014. A compact grazing-incident wide-spectral-range spectrometer based on spherical-variable-line-spacing (SVLS) gratings in the extreme ultraviolet (XUV) region was constructed to optimize and characterize the free-electron laser (FEL) performance at FLASH2. The spectrometer is equipped with three different concave SVLS gratings covering a spectral range from 1 to 62 nm to analyze the spectral characteristics of the XUV radiation. Wavelength calibration and evaluation of the spectral resolution were performed at the plane grating monochromator beamline PG2 at FLASH1 before the installation at FLASH2, and compared with analytical simulations. The first light using self-amplified spontaneous emission from FLASH2 was observed by the spectrometer during a simultaneous operation of both undulator lines—FLASH1 and FLASH2. In addition, the spectral resolution of the spectrometer was evaluated by comparing the measured spectrum from FLASH2 with FEL simulations.

  7. A first glance into the Spectral Energy Distributions of Single Stellar Populations in the Infrared range

    NARCIS (Netherlands)

    Meneses-Goytia, Sofia; Peletier, Reynier F.; Tuffs, RJ; Popescu, CC

    2012-01-01

    The present work shows the Spectral Energy Distributions (SEDs) in the infrared using the IRTF stellar library, obtained using models based on Single Stellar population Models (SSP). We have focused on the K band in order to compare with observables of elliptical galaxies. We also present the compar

  8. A Tape Method for Fast Characterization and Identification of Active Pharmaceutical Ingredients in the 2-18 THz Spectral Range

    Science.gov (United States)

    Kissi, Eric Ofosu; Bawuah, Prince; Silfsten, Pertti; Peiponen, Kai-Erik

    2015-03-01

    In order to find counterfeit drugs quickly and reliably, we have developed `tape method' a transmission spectroscopic terahertz (THz) measurement technique and compared it with a standard attenuated total reflection (ATR) THz spectroscopic measurement. We used well-known training samples, which include commercial paracetamol and aspirin tablets to check the validity of these two measurement techniques. In this study, the spectral features of some active pharmaceutical ingredients (APIs), such as aspirin and paracetamol are characterized for identification purpose. This work covers a wide THz spectral range namely, 2-18 THz. This proposed simple but novel technique, the tape method, was used for characterizing API and identifying their presence in their dosage forms. By comparing the spectra of the APIs to their dosage forms (powder samples), all distinct fingerprints present in the APIs are also present in their respective dosage forms. The positions of the spectral features obtained with the ATR techniques were akin to that obtained from the tape method. The ATR and the tape method therefore, complement each other. The presence of distinct fingerprints in this spectral range has highlighted the possibility of developing fast THz sensors for the screening of pharmaceuticals. It is worth noting that, the ATR method is applicable to flat faced tablets whereas the tape method is suitable for powders in general (e.g. curved surface tablets that require milling before measurement). Finally, we have demonstrated that ATR techniques can be used to screen counterfeit antimalarial tablets.

  9. A feasibility study for the retrieval of the total column precipitable water vapor from satellite observations in the blue spectral range

    Directory of Open Access Journals (Sweden)

    T. Wagner

    2013-04-01

    Full Text Available We present a new algorithm for satellite retrievals of the atmospheric water vapor column in the blue spectral range. The water vapor absorption cross section in the blue spectral range is much weaker than in the red spectral range. Thus the detection limit and the uncertainty of individual observations is systematically larger than for retrievals at longer wavelengths. Nevertheless, water vapor retrievals in the blue spectral range have also several advantages: since the surface albedo in the blue spectral range is similar over land and ocean, water vapor retrievals are more consistent than for longer wavelengths. Compared to retrievals at longer wavelengths, over ocean the sensitivity for atmospheric layers close to the surface is higher due to the (typically 2 to 3 times higher ocean albedo in the blue. Water vapor retrievals in the blue spectral range are also possible for satellite sensors, which do not measure at longer wavelengths of the visible spectral range like the Ozone Monitoring instrument (OMI. We investigated details of the water vapor retrieval in the blue spectral range based on radiative transfer simulations and observations from the Global Ozone Monitoring Experiment 2 (GOME-2 and OMI. It is demonstrated that it is possible to retrieve the atmospheric water vapor column density in the blue spectral range over most parts of the globe. The findings of our study are of importance also for future satellite missions like e.g. Sentinel 4 and 5.

  10. A feasibility study for the retrieval of the total column precipitable water vapour from satellite observations in the blue spectral range

    Directory of Open Access Journals (Sweden)

    T. Wagner

    2013-10-01

    Full Text Available We present a new algorithm for satellite retrievals of the atmospheric water vapour column in the blue spectral range. The water vapour absorption cross section in the blue spectral range is much weaker than in the red spectral range. Thus the detection limit and the uncertainty of individual observations are systematically larger than for retrievals at longer wavelengths. Nevertheless, water vapour retrievals in the blue spectral range have also several advantages: since the surface albedo in the blue spectral range is similar over land and ocean, water vapour retrievals are more consistent than for longer wavelengths. Compared to retrievals at longer wavelengths, the sensitivity for atmospheric layers close to the surface is higher due to the (typically 2 to 3 times higher ocean albedo in the blue. Water vapour retrievals in the blue spectral range are also possible for satellite sensors, which do not measure at longer wavelengths of the visible spectral range like the Ozone Monitoring Instrument (OMI. We investigated details of the water vapour retrieval in the blue spectral range based on radiative transfer simulations and observations from the Global Ozone Monitoring Experiment 2 (GOME-2 and OMI. It is demonstrated that it is possible to retrieve the atmospheric water vapour column density in the blue spectral range over most parts of the globe. The findings of our study are of importance also for future satellite missions (e.g. Sentinel 4 and 5.

  11. Polylogarithmic representation of radiative and thermodynamic properties of thermal radiation in a given spectral range: II. Real-body radiation

    CERN Document Server

    Fisenko, Anatoliy I

    2015-01-01

    The general analytical expressions for the thermal radiative and thermodynamic properties of a real-body are obtained in a finite range of frequencies at different temperatures. The frequency dependence of the spectral emissivity is represented as a power series. The Stefan-Boltzmann law, total energy density, number density of photons, Helmholtz free energy density, internal energy density, enthalpy density, entropy density, heat capacity at constant volume, pressure, and total emissivity are expressed in terms of the polylogarithm functions. The general expressions for the thermal radiative and thermodynamic functions are applied for the study of thermal radiation of liquid and solid zirconium carbide. These functions are calculated using experimental data for the frequency dependence of the normal spectral emissivity in the visible-near infrared range at the melting (freezing) point. The gaps between the thermal radiative and thermodynamic functions of liquid and solid zirconium carbide are observed. The g...

  12. Optical Characterization of Organic Light-Emitting Thin Films in the Ultraviolet and Visible Spectral Ranges

    CERN Document Server

    Montereali, R M; Nichelatti, E; Di Pompeo, F; Segreto, E; Canci, N; Cavanna, F

    2012-01-01

    The spectrophotometric characterization of high efficiency, optically-active samples such as light-emitting organic bulks and thin films can be problematic because their broad-band luminescence is detected together with the monochromatic transmitted and reflected signals, hence perturbing measurements of optical transmittance and reflectance at wavelengths within the photoexcitation band. As a matter of fact, most commercial spectrophotometers apply spectral filtering before the light beam reaches the sample, not after it. In this Report, we introduce and discuss the method we have developed to correct photometric spectra that are perturbed by photoluminescence.

  13. Spectral Unmixing of Forest Crown Components at Close Range, Airborne and Simulated Sentinel-2 and EnMAP Spectral Imaging Scale

    Directory of Open Access Journals (Sweden)

    Anne Clasen

    2015-11-01

    Full Text Available Forest biochemical and biophysical variables and their spatial and temporal distribution are essential inputs to process-orientated ecosystem models. To provide this information, imaging spectroscopy appears to be a promising tool. In this context, the present study investigates the potential of spectral unmixing to derive sub-pixel crown component fractions in a temperate deciduous forest ecosystem. However, the high proportion of foliage in this complex vegetation structure leads to the problem of saturation effects, when applying broadband vegetation indices. This study illustrates that multiple endmember spectral mixture analysis (MESMA can contribute to overcoming this challenge. Reference fractional abundances, as well as spectral measurements of the canopy components, could be precisely determined from a crane measurement platform situated in a deciduous forest in North-East Germany. In contrast to most other studies, which only use leaf and soil endmembers, this experimental setup allowed for the inclusion of a bark endmember for the unmixing of components within the canopy. This study demonstrates that the inclusion of additional endmembers markedly improves the accuracy. A mean absolute error of 7.9% could be achieved for the fractional occurrence of the leaf endmember and 5.9% for the bark endmember. In order to evaluate the results of this field-based study for airborne and satellite-based remote sensing applications, a transfer to Airborne Imaging Spectrometer for Applications (AISA and simulated Environmental Mapping and Analysis Program (EnMAP and Sentinel-2 imagery was carried out. All sensors were capable of unmixing crown components with a mean absolute error ranging between 3% and 21%.

  14. High dynamic range measurement of spectral responsivity and linearity of a radiation thermometer using a super-continuum laser and LEDs

    Energy Technology Data Exchange (ETDEWEB)

    Yoo, Y. S.; Lee, D. H.; Park, C. W.; Park, S. N. [Korea Research Institute of Standards and Science 209 Gajeong-Ro, Yuseong-Gu, Daejon 305-340 (Korea, Republic of)

    2013-09-11

    To realize the temperature scale above the freezing point of silver according to the definition of ITS-90, the dynamic range of the spectral responsivity is one of the most important factors which limit its uncertainty. When the residual spectral response at both side bands of a spectral band is not negligible, a significant uncertainty can be caused by a low dynamic range of the spectral responsivity measurement. In general, incandescent lamps are used to measure the spectral responsivity and the linearity. The dynamic range of the spectral responsivity measurement is often limited by a trade-off with the desired spectral resolution, which is less than 6 decades. Nonlinearity is another limiting fact of uncertainties of the temperature scale. Tungsten lamps have disadvantage in the nonlinearity measurements in terms of adjustability of radiance level and spectral selectivity. We report spectral responsivity measurements of which the measurable dynamic range is enhanced 50 times after replacing a QTH lamp with a super continuum laser. We also present a spectrally selected linearity measurement over a wide dynamic range using high-brightness light emitting diode arrays to observe a slight saturation of linearity.

  15. High-dynamic-range hybrid analog-digital control broadband optical spectral processor using micromirror and acousto-optic devices.

    Science.gov (United States)

    Riza, Nabeel A; Reza, Syed Azer

    2008-06-01

    For the first time, to the best of our knowledge, the design and demonstration of a programmable spectral filtering processor is presented that simultaneously engages the power of an analog-mode optical device such as an acousto-optic tunable filter and a digital-mode optical device such as the digital micromirror device. The demonstrated processor allows a high 50 dB attenuation dynamic range across the chosen 1530-1565 nm (~C band). The hybrid analog-digital spectral control mechanism enables the processor to operate with greater versatility when compared to analog- or digital-only processor designs. Such a processor can be useful both as a test instrument in biomedical applications and as an equalizer in fiber communication networks.

  16. UAS BASED TREE SPECIES IDENTIFICATION USING THE NOVEL FPI BASED HYPERSPECTRAL CAMERAS IN VISIBLE, NIR AND SWIR SPECTRAL RANGES

    Directory of Open Access Journals (Sweden)

    R. Näsi

    2016-06-01

    Full Text Available Unmanned airborne systems (UAS based remote sensing offers flexible tool for environmental monitoring. Novel lightweight Fabry-Perot interferometer (FPI based, frame format, hyperspectral imaging in the spectral range from 400 to 1600 nm was used for identifying different species of trees in a forest area. To the best of the authors’ knowledge, this was the first research where stereoscopic, hyperspectral VIS, NIR, SWIR data is collected for tree species identification using UAS. The first results of the analysis based on fusion of two FPI-based hyperspectral imagers and RGB camera showed that the novel FPI hyperspectral technology provided accurate geometric, radiometric and spectral information in a forested scene and is operational for environmental remote sensing applications.

  17. Spectral optical properties of long-range transport Asian dust and pollution aerosols over Northeast Asia in 2007 and 2008

    Directory of Open Access Journals (Sweden)

    J. Jung

    2010-06-01

    Full Text Available As a part of the IGAC (International Global Atmospheric Chemistry Mega-cities program, aerosol physical and optical properties were continuously measured from March 2007 to March 2008 at an urban site (37.57° N, 126.94° E in Seoul, Korea. Spectral optical properties of long-range transported Asian dust and pollution aerosols have been investigated based on the year long measurement data. Optically measured black carbon/thermally measured elemental carbon (BC/EC ratio showed clear monthly variation with high values in summer and low values in winter mainly due to the enhancement of light attenuation by the internal mixing of EC. Novel approach has been suggested to retrieve the spectral light absorption coefficient (babs from Aethalometer raw data by using BC/EC ratio. Mass absorption efficiency, σabs (=babs/EC at 550 nm was determined to be 9.0±1.3, 8.9±1.5, 9.5±2.0, and 10.3±1.7 m2 g−1 in spring, summer, fall, and winter, respectively with an annual mean of 9.4±1.8 m2 g−1. Threshold values to classify severe haze events were suggested in this study. Increasing trend of aerosol single scattering albedo (SSA with wavelength was observed during Asian dust events while little spectral dependence of SSA was observed during long-range transport pollution (LTP events. Satellite aerosol optical thickness (AOT and Hysplit air mass backward trajectory analyses as well as chemical analysis were performed to characterize the dependence of spectral optical properties on aerosol type. Results from this study can provide useful information for studies on regional air quality and aerosol's effects on climate change.

  18. Infrared normal spectral emissivity of Ti-6Al-4V alloy in the 500-1150 K temperature range

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez-Fernandez, L. [Departamento de Fisica de la Materia Condensada, Facultad de Ciencia y Tecnologia, Universidad del Pais Vasco, Barrio Sarriena s/n, 48940 Leioa, Bizkaia (Spain); Industria de Turbo Propulsores, S.A., Planta de Zamudio, Edificio 300, 48170 Zamudio, Bizkaia (Spain); Risueno, E. [CIC Energigune, Parque Tecnologico, Albert Einstein 48, 01510 Minano, Alava, Spain. (Spain); Perez-Saez, R.B., E-mail: raul.perez@ehu.es [Departamento de Fisica de la Materia Condensada, Facultad de Ciencia y Tecnologia, Universidad del Pais Vasco, Barrio Sarriena s/n, 48940 Leioa, Bizkaia (Spain); Instituto de Sintesis y Estudio de Materiales, Universidad del Pais Vasco, Apdo. 644,48080 Bilbao, Spain. (Spain); Tello, M.J. [Departamento de Fisica de la Materia Condensada, Facultad de Ciencia y Tecnologia, Universidad del Pais Vasco, Barrio Sarriena s/n, 48940 Leioa, Bizkaia (Spain); Instituto de Sintesis y Estudio de Materiales, Universidad del Pais Vasco, Apdo. 644,48080 Bilbao, Spain. (Spain)

    2012-11-15

    Highlights: Black-Right-Pointing-Pointer First heating cycle acts as a annealing, relieving the surface stresses. Black-Right-Pointing-Pointer Stress relieving occurs mainly above 900 K. Black-Right-Pointing-Pointer Emissivity decreases between 0.35 and 0.10 in the 2.5-22 {mu}m spectral range. Black-Right-Pointing-Pointer Emissivity increases linearly with temperature, with the same slope for {lambda} > 10 {mu}m. Black-Right-Pointing-Pointer Good agreement between resistivity and emissivity by means of Hagen-Rubens relation. - Abstract: Thermal radiative emissivity is related to the optical and electrical properties of materials, and it is a key parameter required in a large number of industrial applications. In the case of Ti-6Al-4V, spectral emissivity experimental data are not available for the range of temperatures between 400 and 1200 K, where almost all industrial applications take place. The experimental results in this paper show that the normal spectral emissivity decreases with wavelength from a value of about 0.35 at 2.5 {mu}m to about 0.10 at 22 {mu}m. At the same time, the spectral emissivity shows a slight linear increase with temperature between 500 and 1150 K, with approximately the same slope for all wavelengths. Additionally, the influence of the samples thermal history on the emissivity is studied. A strong decrease in the emissivity values appears due to the effect of surface stress relaxation processes. This means that the radiative properties of this alloy strongly depend on the surface stress state. A thermal treatment to relieve the surface stress should be carried out to achieve a steady state of the radiative properties. In addition, a good qualitative agreement is found between the temperature dependence of the electrical resistivity obtained using conventional measurements and the one obtained from the emissivity experimental results by using the Hagen-Rubens equation.

  19. Analysis of global water vapour trends from satellite measurements in the visible spectral range

    Directory of Open Access Journals (Sweden)

    S. Mieruch

    2008-02-01

    Full Text Available Global water vapour total column amounts have been retrieved from spectral data provided by the Global Ozone Monitoring Experiment (GOME flying on ERS-2, which was launched in April 1995, and the SCanning Imaging Absorption spectroMeter for Atmospheric CHartographY (SCIAMACHY onboard ENVISAT launched in March 2002. For this purpose the Air Mass Corrected Differential Optical Absorption Spectroscopy (AMC-DOAS approach has been used. The combination of the data from both instruments provides us with a long-term global data set spanning more than 11 years with the potential of extension up to 2020 by GOME-2 data on MetOp.

    Using linear and non-linear methods from time series analysis and standard statistics the trends of H2O columns and their errors have been calculated. In this study, factors affecting the trend such as the length of the time series, the magnitude of the variability of the noise, and the autocorrelation of the noise are investigated. Special emphasis has been placed on the calculation of the statistical significance of the observed trends, which reveal significant local changes from −5% per year to +5% per year. These significant trends are distributed over the whole globe. Increasing trends have been calculated for Greenland, East Europe, Siberia and Oceania, whereas decreasing trends have been observed for the northwest USA, Central America, Amazonia, Central Africa and the Arabian Peninsular.

  20. A new undulator for the extension of the spectral range of the CLIO FEL

    Energy Technology Data Exchange (ETDEWEB)

    Marcouille, O.; Berset, J.M.; Glotin, F. [LURE, Orsay (France)] [and others

    1995-12-31

    We built a new undulator in order to extend the lasing range of the CLIO infrared FEL. Presently, CLIO operates in the wavelength range 2 - 17 {mu}m. Beyond 14 {mu}m, the power decreases rapidly, because of the diffraction losses of the vacuum chamber (7 mm height and 2 m long). Thus, lasing at higher wavelengths implies installing a chamber with a height approximately twice. Then the minimum gap is increased and the maximum deflection parameter, K, is reduced from 2 to 1 : the laser tunability is greatly reduced. This is why a new undulator has been built.

  1. Spectral reflectance and soil morphology characteristics of Santa Rita Experimental Range soils

    Science.gov (United States)

    A. Karim Batchily; Donald F. Post; R. B. Bryant; Donald J. Breckenfeld

    2003-01-01

    The Santa Rita Experimental Range (SRER) soils are mostly transported alluvial sediments that occur on the piedmont slope flanking the Santa Rita Mountains in Arizona. The major geomorphic land forms are alluvial fans or fan terraces, but there are also areas of residual soils formed on granite and limestone bedrock, basin floor, stream terraces, and flood plains. The...

  2. Constitutive spectral EEG peaks in the gamma range: suppressed by sleep, reduced by mental activity and resistant to sensory stimulation

    Directory of Open Access Journals (Sweden)

    Tyler Samuel Grummett

    2014-11-01

    Full Text Available Objective: In a systematic study of gamma activity in neuro-psychiatric disease, we unexpectedly observed distinctive, apparently persistent, electroencephalogram (EEG spectral peaks in the gamma range (25-100 Hz. Our objective, therefore, was to examine the incidence, distribution and some of the characteristics of these peaks.Methods: High sample-rate, 128-channel, EEG was recorded in 603 volunteers (510 with neuropsychiatric disorders, 93 controls, whilst performing cognitive tasks, and converted to power spectra. Peaks of spectral power, including in the gamma range, were determined algorithmically for all electrodes. To determine if peaks were stable, 24-hour ambulatory recordings were obtained from 16 subjects with peaks. In 10 subjects, steady-state responses to stimuli at peak frequency were compared with off-peak-frequency stimulation to determine if peaks were a feature of underlying network resonances and peaks were evaluated with easy and hard versions of oddball tasks to determine if peaks might be influenced by mental effort.Results: 57 % of subjects exhibited peaks > 2 dB above trough power at or above 25 Hz. Larger peaks (> 5 dB were present in 13 % of subjects. Peaks were distributed widely over the scalp, more frequent centrally. Peaks were present through the day and were suppressed by slow-wave-sleep. Steady-state responses were the same with on- or off-peak sensory stimulation. In contrast, mental effort resulted in reductions in power and frequency of gamma peaks, although the suppression did not correlate with level of effort.Conclusions: Gamma EEG can be expressed constitutively as concentrations of power in narrow or wide frequency bands that play an, as yet, unknown role in cognitive activity.Significance: These findings expand the described range of rhythmic EEG phenomena. In particular, in addition to evoked, induced and sustained gamma band activity, gamma activity can be present constitutively in spectral peaks.

  3. Ultra low-loss hypocycloid-core Kagome hollow-core photonic crystal fiber for green spectral-range applications.

    Science.gov (United States)

    Debord, B; Alharbi, M; Benoît, A; Ghosh, D; Dontabactouny, M; Vincetti, L; Blondy, J-M; Gérôme, F; Benabid, F

    2014-11-01

    We report on the development of a hypocycloidal-core Kagome hollow-core photonic crystal fiber guiding, with low transmission loss in the 450-650 nm visible spectral range. Transmission loss records have been achieved with 70  dB/km at 600 nm, and 130  dB/km at 532 nm. As a demonstration of the fiber potential applications, we report on a compact 600 THz wide Raman comb generator, centered around 532 nm, and on a 10 W average power frequency-doubled Yb-fiber picosecond laser beam delivery, along with its use for organic material laser micro-processing.

  4. Electrical and thermal tuning of quality factor and free spectral range of optical resonance of nematic liquid crystal microdroplets

    Science.gov (United States)

    Sofi, Junaid Ahmad; Mohiddon, M. A.; Dutta, N.; Dhara, Surajit

    2017-08-01

    We experimentally study the effect of temperature and electric field on the quality (Q ) factor and free spectral range (FSR) of whispering-gallery-mode optical resonance of dye-doped nematic liquid crystal microdroplets. Both the Q factor and the FSR are highly sensitive to the temperature and electric field and are tunable. The Q factor decreases, whereas the FSR increases substantially, with increasing temperature and electric field. The variation of the Q factor and FSR is understood based on the change in the effective refractive index and the dynamic size of the microdroplets.

  5. Impact of blood volume changes within the human skin on the diffuse reflectance measurements in visible and NIR spectral ranges

    Science.gov (United States)

    Zherebtsov, Evgeny; Bykov, Alexander; Popov, Alexey; Doronin, Alexander; Meglinski, Igor

    2017-03-01

    We consider changes in the volume of blood and oxygen saturation caused by a pulse wave and their influence on the diffuse reflectance spectra in the visible/NIR spectral range. CUDA-based Monte-Carlo model was used for routine simulation of detector depth sensitivity (sampling volume) and skin spectra, and their variations associated with physiological changes in the human skin. The results presented in the form of animated graphs of sampling volume changes for scaling of the parameters of the main human skin layers related to the results of experimental measurements are of particular interest for pulse oximetry, photoplethysmography, Doppler flowmetry, reflectance spectroscopy.

  6. Growth and Characterization of Multisegment Chalcogenide Alloy Nanostructures for Photonic Applications in a Wide Spectral Range

    Science.gov (United States)

    Turkdogan, Sunay

    In this dissertation, I described my research on the growth and characterization of various nanostructures, such as nanowires, nanobelts and nanosheets, of different semiconductors in a Chemical Vapor Deposition (CVD) system. In the first part of my research, I selected chalcogenides (such as CdS and CdSe) for a comprehensive study in growing two-segment axial nanowires and radial nanobelts/sheets using the ternary CdSxSe1-x alloys. I demonstrated simultaneous red (from CdSe-rich) and green (from CdS-rich) light emission from a single monolithic heterostructure with a maximum wavelength separation of 160 nm. I also demonstrated the first simultaneous two-color lasing from a single nanosheet heterostructure with a wavelength separation of 91 nm under sufficiently strong pumping power. In the second part, I considered several combinations of source materials with different growth methods in order to extend the spectral coverage of previously demonstrated structures towards shorter wavelengths to achieve full-color emissions. I achieved this with the growth of multisegment heterostructure nanosheets (MSHNs), using ZnS and CdSe chalcogenides, via our novel growth method. By utilizing this method, I demonstrated the first growth of ZnCdSSe MSHNs with an overall lattice mismatch of 6.6%, emitting red, green and blue light simultaneously, in a single furnace run using a simple CVD system. The key to this growth method is the dual ion exchange process which converts nanosheets rich in CdSe to nanosheets rich in ZnS, demonstrated for the first time in this work. Tri-chromatic white light emission with different correlated color temperature values was achieved under different growth conditions. We demonstrated multicolor (191 nm total wavelength separation) laser from a single monolithic semiconductor nanostructure for the first time. Due to the difficulties associated with growing semiconductor materials of differing composition on a given substrate using traditional planar

  7. Image Simulation for Mingantu Ultrawide Spectral Radioheliograph in the Decimetre Wave Range

    Science.gov (United States)

    Du, Jing; Yan, Yihua; Wang, Wei; Liu, Donghao

    2015-06-01

    The MUSER is a solar-dedicated radio interferometric array, which will observe the Sun over a wide range of radio frequencies (0.4-15 GHz), and make high time, space and frequency resolution images of the Sun simultaneously. MUSER is located in Mingantu Station in Inner Mongolia of China, which is about 400 kilometres away from Beijing. MUSER consists of two arrays: MUSER-I and MUSER-II. MUSER-I contains 40 antennas with 4.5-m aperture operating at 400 MHz to 2 GHz. MUSER-II contains 60 antennas with 2-m aperture operating at 2 to 15 GHz. Currently, MUSER has already been established and entered into the stage of test observation. This work is focus on the imaging performance of MUSER-I. This paper introduces MUSER-I briefly, presents the analysis of the array configurations, and evaluates the image quality mainly using the dynamic range, fidelity index, and the peak signal-to-noise ratio, also make some actual solar model simulations with CASA, the results will be shown below.

  8. AlGaN/AlN integrated photonics platform for the ultraviolet and visible spectral range.

    Science.gov (United States)

    Soltani, Mohammad; Soref, Richard; Palacios, Tomas; Englund, Dirk

    2016-10-31

    We analyze a photonic integrated circuit (PIC) platform comprised of a crystalline AlxGa1-xN optical guiding layer on an AlN substrate for the ultraviolet to visible (UV-vis) wavelength range. An Al composition of x~0.65 provides a refractive index difference of ~0.1 between AlxGa1-xN and AlN, and a small lattice mismatch (xGa1-xN/AlN interface. This small refractive index difference is beneficial at shorter wavelengths to avoid extra-small waveguide dimensions. The platform enables compact waveguides and bends with high field confinement in the wavelength range from 700 nm down to 300 nm (and potentially lower) with waveguide cross-section dimensions comparable to those used for telecom PICs such as silicon and silicon nitride waveguides, allowing for well-established optical lithography. This platform can potentially enable cost-effective, manufacturable, monolithic UV-vis photonic integrated circuits.

  9. External quantum efficiency of Pt/n-GaN Schottky diodes in the spectral range 5-500nm

    Energy Technology Data Exchange (ETDEWEB)

    Aslam, Shahid [Raytheon ITSS, 4400 Forbes Boulevard, Lanham, MD 20706 (United States) and Goddard Space Flight Center, NASA, Bld. 11, Rm E015, Greenbelt, MD 20771 (United States)]. E-mail: saslam@pop200.gsfc.nasa.gov; Vest, Robert E. [National Institute of Standards and Technology, 100 Bureau Drive, Gaithersburg, MD 20899 (United States); Franz, David [Raytheon ITSS, 4400 Forbes Boulevard, Lanham, MD 20706 (United States); Goddard Space Flight Center, NASA, Bld. 11, Rm E015, Greenbelt, MD 20771 (United States); Yan Feng [Raytheon ITSS, 4400 Forbes Boulevard, Lanham, MD 20706 (United States); Goddard Space Flight Center, NASA, Bld. 11, Rm E015, Greenbelt, MD 20771 (United States); Zhao Yuegang [Keithley Instruments, Inc., 30500 Bainbridge Rd., Cleveland, OH 44139-2216 (United States); Mott, Brent [Goddard Space Flight Center, NASA, Bld. 11, Rm E015, Greenbelt, MD 20771 (United States)

    2005-02-21

    The external quantum efficiency in the spectral wavelength range 5-500nm of a large active area Pt/n-type GaN Schottky photodiode that exhibits low reverse bias leakage current, is reported. The Schottky photodiodes were fabricated from n{sup -}/n{sup +} epitaxial layers grown by low pressure metalorganic vapour phase epitaxy on single crystal c-plane sapphire. The current-voltage (I-V) characteristics of several 0.25cm{sup 2} devices are presented together with the capacitance-voltage (C-V) characteristics of one of these devices. A leakage current as low as 14 pA at 0.5V reverse bias is reported, for a 0.25cm{sup 2} diode. The ultraviolet quantum efficiency measurements show that the diodes can be used as radiation hard detectors for the 5-365nm spectral range without the use of visible blocking filters. A peak responsivity of 77.5mA/W at 320nm is reported for one of the fabricated devices, corresponding to a spectral detectivity, D*=1.5x10{sup 14}cmHz{sup 1/2}W{sup -1}. The average detectivity between 250 and 350nm, for the same device, is reported to be D-bar*=1.3x10{sup 14}cmHz{sup 1/2}W{sup -1}. The spatial responsivity uniformity variation was established, using H{sub 2} Lyman-{alpha} radiation, to be +/-3% across the surface of a typical 0.25cm{sup 2} diode.

  10. Universal dispersion model for characterization of optical thin films over a wide spectral range: application to hafnia.

    Science.gov (United States)

    Franta, Daniel; Nečas, David; Ohlídal, Ivan

    2015-11-01

    A dispersion model capable of expressing the dielectric response of a broad class of optical materials in a wide spectral range from far IR to vacuum UV is described in detail. The application of this universal dispersion model to a specific material is demonstrated using the ellipsometric and spectrophotometric characterization of a hafnia film prepared by vacuum evaporation on silicon substrate. The characterization utilizes simultaneous processing of data from multiple techniques and instruments covering the wide spectral range and includes the characterization of roughness, nonuniformity, transition layer, and native oxide layer on the back of the substrate. It is shown how the combination of measurements in light reflected from both sides of the sample and transmitted light allows the separation of weak absorption in films and substrates. This approach is particularly useful in the IR region where the absorption structures in films and substrates often overlap and a prior measurement of the bare substrate may be otherwise necessary for precise separation. Individual phenomena that contribute to the dielectric response, i.e., interband electronic transitions, electronic excitations involving the localized states, and phonon absorption, are discussed in detail. A quantitative analysis of absorption on localized states, permitting the separation of transitions between localized states from transitions between localized and extended states, is utilized to obtain estimates of the density of localized states and film stoichiometry.

  11. Polylogarithmic Representation of Radiative and Thermodynamic Properties of Thermal Radiation in a Given Spectral Range: II. Real-Body Radiation

    Science.gov (United States)

    Fisenko, Anatoliy I.; Lemberg, Vladimir

    2015-11-01

    There are several classes of materials and space objects for which the frequency dependence of the spectral emissivity is represented as a power series. Therefore, the study of the properties of thermal radiation for these real bodies is an important task for both fundamental science and industrial applications. The general analytical expressions for the thermal radiative and thermodynamic functions of a real body are obtained in a finite range of frequencies at different temperatures. The Stefan-Boltzmann law, total energy density, number density of photons, Helmholtz free energy density, internal energy density, enthalpy density, entropy density, heat capacity at constant volume, pressure, and total emissivity are expressed in terms of the polylogarithm functions. The obtained general expressions for the thermal radiative and thermodynamic functions are applied for the study of thermal radiation of liquid and solid zirconium carbide. These functions are calculated using experimental data for the frequency dependence of the normal spectral emissivity in the visible and near-infrared range at the melting (freezing) point. The gaps between the thermal radiative and thermodynamic functions of liquid and solid zirconium carbide are observed. The general analytical expressions obtained can easily be presented in the wavenumber domain.

  12. Exploring negative refraction conditions for quantum cascade semiconductor metamaterials in the terahertz spectral range

    Science.gov (United States)

    Daničić, A.; Radovanović, J.; Ramović, S.; Milanović, V.

    2016-03-01

    In order to avoid losses in metamaterial unit cells at frequencies of interest, caused by metallic inclusions, an active medium design has been proposed. As candidate structures for this active medium, we have chosen quantum cascade lasers because of their high output gain. Here we analyze and compare two quantum cascade structures that emit at 4.6 THz and 3.9 THz, respectively, placed under the influence of a strong magnetic field. We first solve the full system of rate equations for all relevant Landau levels, and obtain the necessary information about carrier distribution among the levels, after which we are able to evaluate the permittivity component along the growth direction of the structure. With these data one can determine the conditions under which negative refraction occurs, and calculate the values of the refractive index of the structure, as well as the range of frequencies at which the structure exhibits negative refraction for a predefined total electron sheet density.

  13. Very-large-mode-area photonic bandgap Bragg fiber polarizing in a wide spectral range.

    Science.gov (United States)

    Aleshkina, Svetlana S; Likhachev, Mikhail E; Pryamikov, Andrey D; Gaponov, Dmitry A; Denisov, Alexandr N; Bubnov, Mikhail M; Salganskii, Mikhail Yu; Laptev, Alexandr Yu; Guryanov, Aleksei N; Uspenskii, Yurii A; Popov, Nikolay L; Février, Sébastien

    2011-09-15

    A design of a polarizing all-glass Bragg fiber with a microstructure core has been proposed for the first time. This design provides suppression of high-order modes and of one of the polarization states of the fundamental mode. The polarizing fiber was fabricated by a new, simple method based on a combination of the modified chemical vapor deposition (MCVD) process and the rod-in-tube technique. The mode field area has been found to be about 870 μm² near λ=1064 nm. The polarization extinction ratio better than 13 dB has been observed over a 33% wavelength range (from 1 to 1.4 μm) after propagation in a 1.7 m fiber piece bent to a radius of 70 cm.

  14. Novel SO2 spectral evaluation scheme using the 360–390 nm wavelength range

    Directory of Open Access Journals (Sweden)

    T. Wagner

    2010-03-01

    Full Text Available Differential Optical Absorption Spectroscopy (DOAS is a well established spectroscopic method to determine trace gases in the atmosphere. During the last decade, passive DOAS, which uses solar radiation scattered in the atmosphere as a light source, has become a standard tool to determine SO2 column densities and emission fluxes from volcanoes and other large sources by ground based as well as satellite measurements. For the determination of SO2 column densities, the structured absorption of the molecule in the 300–330 nm region (due to the A1B1←X1A1 transition is used. However, there are several problems limiting the accuracy of the technique in this particular application. Here we propose to use an alternative wavelength region (360–390 nm due to the spin-forbidden a3B2←X1A1 transition for the DOAS evaluation of SO2 in conditions where high SO2 column densities prevail. We show this range to have considerable advantages in such cases, in particular when the particle content of the plume is high and when measurements are performed at large distances from the area of interest.

  15. Novel SO2 spectral evaluation scheme using the 360–390 nm wavelength range

    Directory of Open Access Journals (Sweden)

    T. Wagner

    2010-07-01

    Full Text Available Differential Optical Absorption Spectroscopy (DOAS is a well established spectroscopic method to determine trace gases in the atmosphere. During the last decade, passive DOAS, which uses solar radiation scattered in the atmosphere as a light source, has become a standard tool to determine SO2 column densities and emission fluxes from volcanoes and other large sources by ground based as well as satellite measurements. For the determination of SO2 column densities, the structured absorption of the molecule in the 300–330 nm region (due to the A1B1 ← X1A1 transition is used. However, there are several problems limiting the accuracy of the technique in this particular application. Here we propose to use an alternative wavelength region (360–390 nm due to the spin-forbidden a3B2 ← X1A1 transition for the DOAS evaluation of SO2 in conditions where high SO2 column densities prevail. We show this range to have considerable advantages in such cases, in particular when the particle content of the plume is high and when measurements are performed at large distances from the area of interest.

  16. Development and testing of a fast Fourier transform high dynamic-range spectral diagnostics for millimeter wave characterization

    Energy Technology Data Exchange (ETDEWEB)

    Thoen, D. J.; Bongers, W. A.; Westerhof, E.; Baar, M. R. de; Berg, M. A. van den; Beveren, V. van; Goede, A. P. H.; Graswinckel, M. F.; Schueller, F. C. [Association EURATOM-FOM, Trilateral Euregio Cluster, FOM-Institute for Plasma Physics Rijnhuizen, P.O. Box 1207, 3430 BE Nieuwegein (Netherlands); Oosterbeek, J. W.; Buerger, A. [Association EURATOM-FZJ, Institut fuer Energieforschung-Plasmaphysik, Forschungszentrum Juelich GMBH, 52425 Juelich (Germany); Hennen, B. A. [Association EURATOM-FOM, Trilateral Euregio Cluster, FOM-Institute for Plasma Physics Rijnhuizen, P.O. Box 1207, 3430 BE Nieuwegein (Netherlands); Control Systems Technology Group, Eindhoven University of Technology, P.O. Box 513, NL-5600 MB Eindhoven (Netherlands)

    2009-10-15

    A fast Fourier transform (FFT) based wide range millimeter wave diagnostics for spectral characterization of scattered millimeter waves in plasmas has been successfully brought into operation. The scattered millimeter waves are heterodyne downconverted and directly digitized using a fast analog-digital converter and a compact peripheral component interconnect computer. Frequency spectra are obtained by FFT in the time domain of the intermediate frequency signal. The scattered millimeter waves are generated during high power electron cyclotron resonance heating experiments on the TEXTOR tokamak and demonstrate the performance of the diagnostics and, in particular, the usability of direct digitizing and Fourier transformation of millimeter wave signals. The diagnostics is able to acquire 4 GHz wide spectra of signals in the range of 136-140 GHz. The rate of spectra is tunable and has been tested between 200 000 spectra/s with a frequency resolution of 100 MHz and 120 spectra/s with a frequency resolution of 25 kHz. The respective dynamic ranges are 52 and 88 dB. Major benefits of the new diagnostics are a tunable time and frequency resolution due to postdetection, near-real time processing of the acquired data. This diagnostics has a wider application in astrophysics, earth observation, plasma physics, and molecular spectroscopy for the detection and analysis of millimeter wave radiation, providing high-resolution spectra at high temporal resolution and large dynamic range.

  17. Satellite monitoring of different vegetation types by differential optical absorption spectroscopy (DOAS in the red spectral range

    Directory of Open Access Journals (Sweden)

    T. Wagner

    2007-01-01

    Full Text Available A new method for the satellite remote sensing of different types of vegetation and ocean colour is presented. In contrast to existing algorithms relying on the strong change of the reflectivity in the red and near infrared spectral region, our method analyses weak narrow-band (few nm reflectance structures (i.e. "fingerprint" structures of vegetation in the red spectral range. It is based on differential optical absorption spectroscopy (DOAS, which is usually applied for the analysis of atmospheric trace gas absorptions. Since the spectra of atmospheric absorption and vegetation reflectance are simultaneously included in the analysis, the effects of atmospheric absorptions are automatically corrected (in contrast to other algorithms. The inclusion of the vegetation spectra also significantly improves the results of the trace gas retrieval. The global maps of the results illustrate the seasonal cycles of different vegetation types. In addition to the vegetation distribution on land, they also show patterns of biological activity in the oceans. Our results indicate that improved sets of vegetation spectra might lead to more accurate and more specific identification of vegetation type in the future.

  18. Design concepts of monolithic metamorphic vertical-cavity surface-emitting lasers for the 1300–1550 nm spectral range

    Energy Technology Data Exchange (ETDEWEB)

    Egorov, A. Yu., E-mail: anton@beam.ioffe.ru; Karachinsky, L. Ya.; Novikov, I. I.; Babichev, A. V.; Nevedomskiy, V. N. [Russian Academy of Sciences, Ioffe Institute (Russian Federation); Bugrov, V. E. [ITMO University (Russian Federation)

    2015-11-15

    Possible design concepts for long-wavelength vertical-cavity surface-emitting lasers for the 1300–1550 nm spectral range on GaAs substrates are suggested. It is shown that a metamorphic GaAs–InGaAs heterostructure with a thin buffer layer providing rapid transition from the lattice constant of GaAs to that of In{sub x}Ga{sub 1–x}As with an indium fraction of x < 0.3 can be formed by molecular-beam epitaxy. Analysis by transmission electron microscopy demonstrated the effective localization of mismatch dislocations in the thin buffer layer and full suppression of their penetration into the overlying InGaAs metamorphic layer.

  19. Quantum efficiency of cesium iodide photocathodes in the 120-220 nm spectral range traceable to a primary detector standard

    CERN Document Server

    Rabus, H; Richter, M; Ulm, G; Friese, J; Gernhäuser, R; Kastenmüller, A; Maier-Komor, P; Zeitelhack, K

    1999-01-01

    Differently prepared CsI samples have been investigated in the 120-220 nm spectral range for their quantum efficiency, spatial uniformity and the effect of radiation aging. The experiments were performed at the PTB radiometry laboratory at the Berlin synchrotron radiation facility BESSY. A calibrated GaAsP Schottky photodiode was used as transfer detector standard to establish traceability to the primary detector standard, because this type of photodiode - unlike silicon p-on-n photodiodes - proved to be of sufficiently stable response when exposed to vacuum ultraviolet radiation. The paper reviews the experimental procedures that were employed to characterize and calibrate the GaAsP photodiode and reports the results that were obtained on the investigated CsI photocathodes.

  20. InGaN light emitting diodes for 415 nm-520 nm spectral range by plasma assisted MBE

    Energy Technology Data Exchange (ETDEWEB)

    Szankowska, M.L.; Smalc-Koziorowska, J.; Cywinski, G.; Grzanka, S.; Grzegory, I.; Lucznik, B. [Institute of High Pressure Physics, Polish Academy of Sciences, 01-142 Warszawa (Poland); Feduniewicz-Zmuda, A. [TopGaN Ltd, ul Sokolowska 29/37, 01-142 Warszawa (Poland); Wasilewski, Z.R. [Institute for Microstructural Sciences, National Research Council, Ottawa (Canada); Porowski, S.; Skierbiszewski, C. [Institute of High Pressure Physics, Polish Academy of Sciences, 01-142 Warszawa (Poland); TopGaN Ltd, ul Sokolowska 29/37, 01-142 Warszawa (Poland); Siekacz, M

    2009-06-15

    In this work we study the growth of the Light Emitting Diodes (LEDs) by Plasma Assisted MBE (PAMBE). The active LEDs region was grown to cover the spectral range spanning from 415 nm to 520 nm. We demonstrate efficient LEDs with the highest optical power output of 1.5 mW and 20 mA for 415 nm. For longer wavelengths we observe a drop of the optical power. The reduction of the quantum efficiency for green emission can be related to the presence of strong built-in piezoelectric fields or increased number of nonradiative recombination centers. (copyright 2009 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  1. An improved algorithm for the determination of aerosol optical depth in the ultraviolet spectral range from Brewer spectrophotometer observations

    Science.gov (United States)

    Sellitto, P.; di Sarra, A.; Siani, A. M.

    2006-10-01

    Methods to derive aerosol optical depth in the UV spectral range from ground-based remote-sensing stations equipped with Brewer spectrophotometers have been recently developed. In this study a modified Langley plot method has been implemented to retrieve aerosol optical depth from direct sun Brewer measurements. The method uses measurements over an extended range of atmospheric airmasses obtained with two different neutral density filters, and accounts for short-term variations of total ozone, derived from the same direct sun observations. The improved algorithm has been applied to data collected with a Brewer mark IV, operational in Rome, Italy, and with a Brewer mark III, operational in Lampedusa, Italy, in the Mediterranean. The efficiency of the improved algorithm has been tested comparing the number of determinations of the extraterrestrial constant against those obtained with a standard Langley plot procedure. The improved method produces a larger number of reliable Langley plots, allowing for a better statistical characterization of the extraterrestrial constant and a better study of its temporal variability. The values of aerosol optical depth calculated in Rome and Lampedusa compare well with simultaneous determinations in the 416-440 nm interval derived from MFRSR and CIMEL measurements.

  2. Observing ice clouds in the submillimeter spectral range: the CloudIce mission proposal for ESA's Earth Explorer 8

    Directory of Open Access Journals (Sweden)

    S. A. Buehler

    2012-02-01

    Full Text Available Passive submillimeter-wave sensors are a way to obtain urgently needed global data on ice clouds, particularly on the so far poorly characterized "essential climate variable" ice water path (IWP and on ice particle size. CloudIce was a mission proposal to the European Space Agency ESA in response to the call for Earth Explorer 8 (EE8, which ran in 2009/2010. It proposed a passive submillimeter-wave sensor with channels ranging from 183 GHz to 664 GHz. The article describes the CloudIce mission proposal, with particular emphasis on describing the algorithms for the data-analysis of submillimeter-wave cloud ice data (retrieval algorithms and demonstrating their maturity. It is shown that we have a robust understanding of the radiative properties of cloud ice in the millimeter/submillimeter spectral range, and that we have a proven toolbox of retrieval algorithms to work with these data. Although the mission was not selected for EE8, the concept will be useful as a reference for other future mission proposals.

  3. Observing ice clouds in the submillimeter spectral range: the CloudIce mission proposal for ESA's Earth Explorer 8

    Directory of Open Access Journals (Sweden)

    S. A. Buehler

    2012-07-01

    Full Text Available Passive submillimeter-wave sensors are a way to obtain urgently needed global data on ice clouds, particularly on the so far poorly characterized "essential climate variable" ice water path (IWP and on ice particle size. CloudIce was a mission proposal to the European Space Agency ESA in response to the call for Earth Explorer 8 (EE8, which ran in 2009/2010. It proposed a passive submillimeter-wave sensor with channels ranging from 183 GHz to 664 GHz. The article describes the CloudIce mission proposal, with particular emphasis on describing the algorithms for the data-analysis of submillimeter-wave cloud ice data (retrieval algorithms and demonstrating their maturity. It is shown that we have a robust understanding of the radiative properties of cloud ice in the millimeter/submillimeter spectral range, and that we have a proven toolbox of retrieval algorithms to work with these data. Although the mission was not selected for EE8, the concept will be useful as a reference for other future mission proposals.

  4. CCPR-S1 Supplementary comparison for spectral radiance in the range of 220 nm to 2500 nm

    Science.gov (United States)

    Khlevnoy, Boris; Sapritsky, Victor; Rougie, Bernard; Gibson, Charles; Yoon, Howard; Gaertner, Arnold; Taubert, Dieter; Hartmann, Juergen

    2009-08-01

    In 1997, the Consultative Committee for Photometry and Radiometry (CCPR) initiated a supplementary comparison of spectral radiance in the wavelength range from 220 nm to 2500 nm (CCPR-S1) using tungsten strip-filament lamps as transfer standards. Five national metrology institutes (NMIs) took part in the comparison: BNM/INM (France), NIST (USA), NRC (Canada), PTB (Germany) and VNIIOFI (Russia), with VNIIOFI as the pilot laboratory. Each NMI provided the transfer lamps that were used to transfer their measurements to the pilot laboratory. The intercomparison sequence began with the participant measurements, then the pilot measurements, followed by a second set of measurements by the participant laboratory. The measurements were carried out from 1998 to 2002, with the final report completed in 2008. This paper presents the descriptions of measurement facilities and uncertainties of the participants, as well as the comparison results that were analysed in accordance with the Guidelines for CCPR Comparisons Report Preparation, and a re-evaluation of the results taking into account the instability of some of the transfer lamps. Excluding a few wavelengths, all participants agree with each other within ±1.5%. The disagreement decreases to approximately ±1.0% when the anomalous data are excluded from the analysis.

  5. Effects of external intermittency and mean shear on the spectral inertial-range exponent in a turbulent square jet.

    Science.gov (United States)

    Zhang, J; Xu, M; Pollard, A; Mi, J

    2013-05-01

    This study investigates by experiment the dependence of the inertial-range exponent m of the streamwise velocity spectrum on the external intermittency factor γ (≡ the fraction of time the flow is fully turbulent) and the mean shear S in a turbulent square jet. Velocity measurements were made using hot-wire anemometry in the jet at 15 < x/D(e) < 40, where D(e) denotes the exit equivalent diameter, and for an exit Reynolds number of Re = 50,000. The Taylor microscale Reynolds number R(λ) varies from about 70 to 450 in the present study. The TERA (turbulent energy recognition algorithm) method proposed by Falco and Gendrich [in Near-Wall Turbulence: 1988 Zoran Zariç Memorial Conference, edited by S. J. Kline and N. H. Afgan (Hemisphere Publishing Corp., Washington, DC, 1990), pp. 911-931] is discussed and applied to estimate the intermittency factor from velocity signals. It is shown that m depends strongly on γ but negligibly on S. More specifically, m varies with γ following m=m(t)+(lnγ(-0.0173))(1/2), where m(t) denotes the spectral exponent found in fully turbulent regions.

  6. Beta-range cortical motor spectral power and corticomuscular coherence as a mechanism for effective corticospinal interaction during steady-state motor output.

    Science.gov (United States)

    Kristeva, Rumyana; Patino, Luis; Omlor, Wolfgang

    2007-07-01

    The steady-state motor output, occurring during static force, is characterized by synchronization between oscillatory cortical motor and muscle activity confined to the beta frequency range (15-30 Hz). The functional significance of this beta-range coherence remains unclear. We hypothesized that if the beta-range coherence had a functional role, it would have a behavioral correlate; specifically, it would be related to the precision of the steady-state motor output. To test this hypothesis, we investigated the corticomuscular (EEG-EMG) coherence in eight healthy subjects during steady-state motor output in a visuomotor task, in which the subjects exerted a static force with their right index finger to keep a visual cursor within a target zone. We show that the beta-range EEG-EMG coherence is related to the behavioral performance, i.e. the error signal between target and exerted force. Furthermore, we show that the amplitude of the cortical spectral power is also related to the performance. Moreover, we provide evidence that the EEG-EMG coherence and the cortical spectral power are not completely independent phenomena. Together, our findings indicate that higher beta-range cortical spectral power and increased corticospinal coherence in the beta-range improve motor performance during steady-state motor output. This suggests that the beta-range cortical motor spectral power and corticomuscular coherence may promote effective corticospinal interaction.

  7. Formando planetas habitables en estrellas M3

    Science.gov (United States)

    Dugaro, A.; de Elía, G. C.; Brunini, A.

    2016-08-01

    Studies of stellar evolution allow us to infer that the low-mass stars are the most abundant in the galaxy. In the present investigation, we analyze the formation of planetary systems without gas giants around M3-type stars, which have a mass of 0.29 M. In particular, we are interested in studying the terrestrial-like planet formation processes and water delivery in the Habitable Zone (HZ) of those systems. To develop this investigation, we assume massive protoplanetary disks for such stars, which have 5 of the mass of the central star. Once defined the working disk, we use a semi-analytical model, which is able to determine the distribution of planetary embryos and planetesimals at the end of the gaseous phase. Then, these distributions are used as initial conditions for running -body simulations. Due to the stochastic nature of the accretion process, we carry out ten -body simulations in order to analyze the evolution of the planetary systems after the gas dissipation. Our results suggest the efficient formation of terrestrial-like planets in the HZ with a wide range of masses and water contents. The planets formed in the HZ of the system have masses between 0.07 M and 0.15 M and final water contents between 5.4 and 29 by mass. The physical properties of the terrestrial-like planets formed in the HZ of our simulations suggest that they should be able to retain a permanent and substantial atmosphere.

  8. Spectral emissivity modeling of steel 201 during the growth of oxidation film over the temperature range from 800 to 1100 K in air

    Science.gov (United States)

    Shi, Deheng; Zou, Fenghui; Wang, Shuai; Zhu, Zunlue; Sun, Jinfeng; Wang, Baokui

    2014-11-01

    This study explores the spectral emissivity modeling of steel 201 during the growth of oxidation film over the temperature range from 800 to 1100 K at 1.5 μm. The radiance coming from the specimen is received by an InGaAs photodiode detector. The specimen temperature is obtained by averaging the two platinum-rhodium thermocouples, which are tightly welded in the front surface of specimen near the measuring area viewed by the detector. The variation of spectral emissivity with the temperature is studied at a given heating time. The variation of spectral emissivity with the heating time is evaluated at a definite temperature. The strong oscillations of spectral emissivity are observed and discussed in detail, which originate from the interference effect between the radiation stemming from the oxidization film on the specimen surface and the radiation coming from the specimen surface. The measurement uncertainties of spectral emissivity contributed only by the surface oxidization are about 3.2-14.1%. At a given heating time, the variation of spectral emissivity with the temperature abides well by a simple analytic functional form. And at a definite temperature, the variation of spectral emissivity with the heating time can also be well reproduced by fitting except for the periodical oscillations.

  9. A single-shot nonlinear autocorrelation approach for time-resolved physics in the vacuum ultraviolet spectral range

    Energy Technology Data Exchange (ETDEWEB)

    Rompotis, Dimitrios

    2016-02-15

    In this work, a single-shot temporal metrology scheme operating in the vacuum-extreme ultraviolet spectral range has been designed and experimentally implemented. Utilizing an anti-collinear geometry, a second-order intensity autocorrelation measurement of a vacuum ultraviolet pulse can be performed by encoding temporal delay information on the beam propagation coordinate. An ion-imaging time-of-flight spectrometer, offering micrometer resolution has been set-up for this purpose. This instrument enables the detection of a magnified image of the spatial distribution of ions exclusively generated by direct two-photon absorption in the combined counter-propagating pulse focus and thus obtain the second-order intensity autocorrelation measurement on a single-shot basis. Additionally, an intense VUV light source based on high-harmonic generation has been experimentally realized. It delivers intense sub-20 fs Ti:Sa fifth-harmonic pulses utilizing a loose-focusing geometry in a long Ar gas cell. The VUV pulses centered at 161.8 nm reach pulse energies of 1.1 μJ per pulse, while the corresponding pulse duration is measured with a second-order, fringe-resolved autocorrelation scheme to be 18 ± 1 fs on average. Non-resonant, two-photon ionization of Kr and Xe and three-photon ionization of Ne verify the fifth-harmonic pulse intensity and indicate the feasibility of multi-photon VUV pump/VUV probe studies of ultrafast atomic and molecular dynamics. Finally, the extended functionally of the counter-propagating pulse metrology approach is demonstrated by a single-shot VUV pump/VUV probe experiment aiming at the investigation of ultrafast dissociation dynamics of O{sub 2} excited in the Schumann-Runge continuum at 162 nm.

  10. Influence of the number of atomic levels on the spectral opacity of low temperature nickel and iron in the spectral range 50–300 eV

    Directory of Open Access Journals (Sweden)

    Busquet M.

    2013-11-01

    Full Text Available Opacity is a fundamental ingredient for the secular evolution of stars. The calculation of the stellar plasma absorption coefficients is complex due to the composition of these plasmas, generally an H /He dominated mixture with a low concentration of partially ionized heavy ions (the iron group. The international collaboration OPAC recently presented extensive comparisons of spectral opacities of iron and nickel for temperatures between 15 and 40 eV and for densities of ∼ 3 mg/cm3, relevant to the stellar envelope conditions [1, 2]. The role of Configuration Interaction (CI and the influence of the number of atomic levels on the opacity using the recently improved version of HULLAC atomic code [3, 4] are illustrated in this article. Comparisons with theoretical predictions already presented in [1] are discussed.

  11. New acceptor-bridge-donor strategy for enhancing NLO response with long-range excess electron transfer from the NH2...M/M3O donor (M = Li, Na, K) to inside the electron hole cage C20F19 acceptor through the unusual σ chain bridge (CH2)4.

    Science.gov (United States)

    Bai, Yang; Zhou, Zhong-Jun; Wang, Jia-Jun; Li, Ying; Wu, Di; Chen, Wei; Li, Zhi-Ru; Sun, Chia-Chung

    2013-04-01

    Using the strong electron hole cage C20F19 acceptor, the NH2...M/M3O (M = Li, Na, and K) complicated donors with excess electron, and the unusual σ chain (CH2)4 bridge, we construct a new kind of electride molecular salt e(-)@C20F19-(CH2)4-NH2...M(+)/M3O(+) (M = Li, Na, and K) with excess electron anion inside the hole cage (to be encapsulated excess electron-hole pair) serving as a new A-B-D strategy for enhancing nonlinear optical (NLO) response. An interesting push-pull mechanism of excess electron generation and its long-range transfer is exhibited. The excess electron is pushed out from the (super)alkali atom M/M3O by the lone pair of NH2 in the donor and further pulled inside the hole cage C20F19 acceptor through the efficient long σ chain (CH2)4 bridge. Owing to the long-range electron transfer, the new designed electride molecular salts with the excess electron-hole pair exhibit large NLO response. For the e(-)@C20F19-(CH2)4-NH2...Na(+), its large first hyperpolarizability (β0) reaches up to 9.5 × 10(6) au, which is about 2.4 × 10(4) times the 400 au for the relative e(-)@C20F20...Na(+) without the extended chain (CH2)4-NH2. It is shown that the new strategy is considerably efficient in enhancing the NLO response for the salts. In addition, the effects of different bridges and alkali atomic number on β0 are also exhibited. Further, three modulating factors are found for enhancing NLO response. They are the σ chain bridge, bridge-end group with lone pair, and (super)alkali atom. The new knowledge may be significant for designing new NLO materials and electronic devices with electrons inside the cages. They may also be the basis of establishing potential organic chemistry with electron-hole pair.

  12. Spectral redistribution of energy and the origin of inverse cascade for gyrokinetics in the sub-Larmor range

    CERN Document Server

    Plunk, G G

    2010-01-01

    It is known that an inverse cascade of energy occurs in two-dimensional neutral fluid turbulence and also, under certain conditions, in magnetized plasma turbulence. The reason for this phenomenon in both cases is due to the existence of two quadratic invariants. The crucial feature of these invariants is that they are {\\em mutually-constraining} in the sense that the spectral redistribution of one is constrained by the other. The gyrokinetic equation, a kinetic equation for magnetized plasma dynamics, has two collisionless quadratic invariants when restricted to two dimensions (in position-space). In this paper, we consider the consequences of this fact for scales smaller than the thermal Larmor radius, where turbulent fluctuations exist, with equal importance, in the position and velocity space dependence of the kinetic distribution function. Using a spectral formalism for position and velocity space, we find that the gyrokinetic invariants are mutually constraining with respect to spectral redistribution o...

  13. Microscopic nucleon spectral function for finite nuclei featuring two- and three-nucleon short-range correlations: The model versus ab initio calculations for three-nucleon systems

    Science.gov (United States)

    Ciofi degli Atti, Claudio; Mezzetti, Chiara Benedetta; Morita, Hiko

    2017-04-01

    Background: Two-nucleon (2 N ) short-range correlations (SRC) in nuclei have been recently thoroughly investigated, both theoretically and experimentally and the study of three-nucleon (3 N ) SRC, which could provide important information on short-range hadronic structure, is underway. Novel theoretical ideas concerning 2 N and 3 N SRC are put forward in the present paper. Purpose: The general features of a microscopic one-nucleon spectral function which includes the effects of both 2 N and 3 N SRC and its comparison with ab initio spectral functions of the three-nucleon systems are illustrated. Methods: A microscopic and parameter-free one-nucleon spectral function expressed in terms of a convolution integral involving ab initio relative and center-of-mass (c.m.) momentum distributions of a 2 N pair and aimed at describing two- and three-nucleon short-range correlations, is obtained by using: (i) the two-nucleon momentum distributions obtained within ab initio approaches based upon nucleon-nucleon interactions of the Argonne family; (ii) the exact relation between one- and two-nucleon momentum distributions; (iii) the fundamental property of factorization of the nuclear wave function at short internucleon ranges. Results: The comparison between the ab initio spectral function of 3He and the one based upon the convolution integral shows that when the latter contains only two-nucleon short-range correlations the removal energy location of the peaks and the region around them exhibited by the ab initio spectral function are correctly predicted, unlike the case of the high and low removal energy tails; the inclusion of the effects of three-nucleon correlations brings the convolution model spectral function in much better agreement with the ab initio one; it is also found that whereas the three-nucleon short-range correlations dominate the high energy removal energy tail of the spectral function, their effects on the one-nucleon momentum distribution are almost one

  14. Design of a sun tracker for the automatic measurement of spectral irradiance and construction of an irradiance database in the 330-1100 nm range

    Energy Technology Data Exchange (ETDEWEB)

    Canada, J.; Maj, A. [Departamento de Termodinamica Aplicada, Universidad Politecnica de Valencia, Camino de Vera, s/n. 46022 Valencia (Spain); Utrillas, M.P.; Martinez-Lozano, J.A.; Pedros, R.; Gomez-Amo, J.L. [Departamento de Fisica de la Tierra y Termodinamica, Facultat de Fisica, Universitat de Valencia, 46100 Burjassot (Valencia) (Spain)

    2007-10-15

    An automatic global and direct solar spectral irradiance system has been designed based on two LICOR spectro radiometers equipped with fibre optics and remote cosine sensors. To measure direct irradiance a sun tracker based on step motors has been developed. The whole system is autonomous and works continuously. From the measurements provided by this system a spectral irradiance database in the 330-1100 nm range has been created. This database contains normal direct and global horizontal irradiances as well as diffuse irradiance on a horizontal plane, together with total atmospheric optical thickness and aerosol optical depth. (author)

  15. Spectral emission properties of a laser-produced plasma light source in the sub-200 nm range for wafer inspection applications

    Science.gov (United States)

    Gambino, Nadia; Rollinger, Bob; Hudgins, Duane; Abhari, Reza S.

    2015-07-01

    The spectral emission properties of a droplet-based laser-produced plasma are investigated in the vacuum ultraviolet (VUV) range. Measurements are performed with a spectrograph that operates from 30 to 180 nm with a spectral resolution of 0.1 nm. The emission spectra are recorded for different metal droplet targets, namely tin, indium, and gallium. Measurements were performed at different pressure levels of the background gas. Several characteristic emission lines are observed. The spectra are also calibrated in intensity in terms of spectral radiance to allow absolute emission power estimations from the light source in the VUV region. The presented experimental results are relevant for alternative light sources that would be needed for future wafer inspection tools. In addition, the experimental results help to determine the out-of-band radiation emission of a tin-based extreme ultraviolet (EUV) source. By tuning the type of fuel, the laser energies, and the background gas, the laser-produced plasma light source shows good capabilities to be operated as a light source that covers a spectral emission range from the EUV to the sub-200 nm range.

  16. Full-disk observations of the saturnian moons in the VIS-NIR spectral range by Cassini- VIMS

    Science.gov (United States)

    Filacchione, G.; Capaccioni, F.; Coradini, A.; Cerroni, P.; Tosi, F.; Adriani, A.; McCord, T. B.; Baines, K. H.; Bellucci, G.; Brown, R. H.; Bibring, J.; Buratti, B. J.; Clark, R. N.; Combes, M.; Cruikshank, D. P.; Drossart, P.; Formisano, V.; Jaumann, R.; Langevin, Y.; Matson, D. L.; Mennella, V.; Robert, N. M.; Nicholson, P. D.; Sicardy, B.; Sotin, C.; Moriconi, M.

    2006-12-01

    During the first two years of the Cassini's nominal mission, VIMS (Visual and Infrared Mapping Spectrometer) has explored the whole system of Saturnian icy satellites. Here we report a comparative analysis of more than 600 full-disk observations obtained from July 2004 to nowadays for 15 regular and minor satellites: Atlas, Prometheus, Pandora, Janus, Epimetheus, Mimas, Enceladus, Tethys, Telesto, Calypso, Dione, Rhea, Hyperion, Iapetus and Phoebe. These observations, done from the equatorial plane, are particularly suitable to highlight the spectral differences between the leading and trailing sides of the regular satellites as function of the illumination angle (Filacchione et al., 2006a, 2006b); a byproduct of this activity is the measurement of the phase curves. The combined use of several VIS and IR spectral quantities (e.g. spectral slopes, water ice bands strengths, continuum levels, etc.) allows to find correlations between classes of satellites orbiting at different distances from Saturn: in this way it is possible to discriminate the almost pure ice surfaces of Enceladus and Calypso from the organic rich Hyperion, Iapetus and Phoebe (Tosi et al., 2006). This research was completed thanks to the support of the Italian Space Agency (ASI), Grant ASI/Cassini I/031/05/0. Filacchione et al., 2006a. Saturn's icy satellites investigated by Cassini-VIMS. I. Full-disk properties: 350-5100 nm reflectance spectra and phase curves, Icarus, in press. Filacchione et al., 2006b. VIS-NIR Spectral Properties of Saturn's Minor Icy Moons. 37th LPSC, abstract no.1271 Tosi et al., 2006. Iapetus, Phoebe and Hyperion: Are They Related? 37th LPSC, abstract no.1582

  17. Broadband photon time-of-flight spectroscopy of pharmaceuticals and highly scattering plastics in the VIS and close NIR spectral ranges.

    Science.gov (United States)

    Khoptyar, Dmitry; Subash, Arman Ahamed; Johansson, Sören; Saleem, Muhammad; Sparén, Anders; Johansson, Jonas; Andersson-Engels, Stefan

    2013-09-01

    We present extended spectroscopic analysis of pharmaceutical tablets in the close near infrared spectral range performed using broadband photon time-of-flight (PTOF) absorption and scattering spectra measurements. We show that the absorption spectra can be used to perform evaluation of the chemical composition of pharmaceutical tablets without need for chemo-metric calibration. The spectroscopic analysis was performed using an advanced PTOF spectrometer operating in the 650 to 1400 nm spectral range. By employing temporal stabilization of the system we achieve the high precision of 0.5% required to evaluate the concentration of tablet ingredients. In order to further illustrate the performance of the system, we present the first ever reported broadband evaluation of absorption and scattering spectra from pure and doped Spectralon®.

  18. Investigation of the spectral characteristics of a pulsed F/sub 2/-center laser tunable in the range 1. 1--1. 26. mu

    Energy Technology Data Exchange (ETDEWEB)

    Gusev, Y.L.; Kirpichnikov, A.V.; Marennikov, S.I.

    1979-12-01

    A description is given of a simple resonator system in which single-frequency stimulated emission was achieved from a pulsed F-center laser. The average line width due to fluctuations of the lasing frequency was 0.01 cm/sup -1/ in the 1.1--1.26 ..mu.. spectral range. Investigations were made of the reasons for these fluctuations and numerical estimates were made of the different factors responsible for these fluctuations.

  19. 3D coaxial out-of-plane metallic antennas for filtering and multi-spectral imaging in the infrared range.

    Science.gov (United States)

    Jacassi, Andrea; Bozzola, Angelo; Zilio, Pierfrancesco; Tantussi, Francesco; De Angelis, Francesco

    2016-06-27

    We fabricated and investigated a new configuration of 3D coaxial metallic antennas working in the infrared which combines the strong lateral light scattering of vertical plasmonic structures with the selective spectral transmission of 2D arrays of coaxial apertures. The coaxial structures are fabricated with a top-down method based on a template of hollow 3D antennas. Each antenna has a multilayer radial structure consisting of dielectric and metallic materials not achievable in a 2D configuration. A planar metallic layer is inserted normally to the antennas. The outer dielectric shell of the antenna defines a nanometric gap between the horizontal plane and the vertical walls. Thanks to this aperture, light can tunnel to the other side of the plane, and be transmitted to the far field in a set of resonances. These are investigated with finite-elements electromagnetic calculations and with Fourier-transform infrared spectroscopy measurements. The spectral position of the resonances can be tuned by changing the lattice period and/or the antenna length. Thanks to the strong scattering provided by the 3D geometry, the transmission peaks possess a high signal-to-noise ratio even when the illuminated area is less than 2 × 2 times the operation wavelength. This opens new possibilities for multispectral imaging in the IR with wavelength-scale spatial resolution.

  20. Lasing of multiperiod quantum-cascade lasers in the spectral range of (5.6–5.8)-μm under current pumping

    Energy Technology Data Exchange (ETDEWEB)

    Egorov, A. Yu., E-mail: anton@beam.ioffe.ru; Babichev, A. V.; Karachinsky, L. Ya.; Novikov, I. I. [Ioffe Institute (Russian Federation); Nikitina, E. V. [St. Petersburg Academic University (Russian Federation); Tchernycheva, M. [University Paris Sud XI, Institut d’Electronique Fondamentale (France); Sofronov, A. N.; Firsov, D. A.; Vorobjev, L. E. [Peter the Great St. Petersburg Polytechnic University (Russian Federation); Pikhtin, N. A.; Tarasov, I. S. [Ioffe Institute (Russian Federation)

    2015-11-15

    The lasing of multiperiod quantum-cascade lasers in the spectral range of (5.6–5.8)-μm under current pumping are demonstrated. The quantum-cascade laser heterostructure is grown by molecular-beam epitaxy technique. Despite the relatively short laser cavity length and high level of external loss the laser shows the lasing in the temperature range of 80–220 K. The threshold current density below 4 kA/cm{sup 2} at 220 K with the characteristic temperature T{sub 0} = 123 K was demonstrated.

  1. The Luminosity Function of M3

    CERN Document Server

    Rood, R T; Paltrinieri, B; Ferraro, F R; Pecci, F F; Dorman, B; Chieffi, A; Straniero, O; Buonanno, R

    1999-01-01

    We present a high precision, large sample luminosity function (LF) for the Galactic globular cluster M3. With a combination of ground based and Hubble Space Telescope data we cover the entire radial extent of the cluster. The observed LF is well fit by canonical standard stellar models from the red giant branch (RGB) tip to below the main sequence turnoff point. Specifically, neither the RGB LF-bump nor subgiant branch LF indicate any breakdown in the standard models. On the main sequence we find evidence for a flat initial mass function and for mass segregation due to the dynamical evolution of the cluster.

  2. Modelling the spectral induced polarization response of water-saturated sands in the intermediate frequency range (102-105 Hz) using mechanistic and empirical approaches

    Science.gov (United States)

    Kremer, Thomas; Schmutz, Myriam; Leroy, Philippe; Agrinier, Pierre; Maineult, Alexis

    2016-11-01

    The intermediate frequency range 102-105 Hz forms the transition range between the spectral induced polarization frequency domain and the dielectric spectroscopy frequency domain. Available experimental data showed that the spectral induced polarization response of sands fully saturated with water was particularly sensitive to variations of the saturating water electrical conductivity value in the intermediate frequency range. An empirical and a mechanistic model have been developed and confronted to this experimental data. This confrontation showed that the Maxwell Wagner polarization alone is not sufficient to explain the observed signal in the intermediate frequency range. The SIP response of the media was modelled by assigning relatively high dielectric permittivity values to the sand particle or high effective permittivity values to the media. Such high values are commonly observed in the dielectric spectroscopy literature when entering the intermediate frequency range. The physical origin of these high dielectric permittivity values is discussed (grain shape, electromagnetic coupling), and a preliminary study is presented which suggests that the high impedance values of the non-polarizable electrodes might play a significant role in the observed behaviour.

  3. Gas-phase absorption cross sections of 24 monocyclic aromatic hydrocarbons in the UV and IR spectral ranges

    Science.gov (United States)

    Etzkorn, Thomas; Klotz, Björn; Sørensen, Søren; Patroescu, Iulia V.; Barnes, Ian; Becker, Karl H.; Platt, Ulrich

    Absorption cross sections of 24 volatile and non-volatile derivatives of benzene in the ultraviolet (UV) and the infrared (IR) regions of the electromagnetic spectrum have been determined using a 1080 l quartz cell. For the UV a 0.5 m Czerny-Turner spectrometer coupled with a photodiode array detector (spectral resolution 0.15 nm) was used. IR spectra were recorded with an FT-IR spectrometer (Bruker IFS-88, spectral resolution 1 cm -1). Absolute absorption cross sections and the instrument function are given for the UV, while for the IR, absorption cross sections and integrated band intensities are reported. The study focused primarily on the atmospherically relevant methylated benzenes (benzene, toluene, o-xylene, m-xylene, p-xylene, 1,2,4-trimethylbenzene, 1,3,5-trimethylbenzene, ethylbenzene, styrene) and their ring retaining oxidation products (benzaldehyde, o-tolualdehyde, m-tolualdehyde, p-tolualdehyde, phenol, o-cresol, m-cresol, p-cresol, 2,3-dimethylphenol, 2,4-dimethylphenol, 2,5-dimethylphenol, 2,6-dimethylphenol, 3,4-dimethylphenol, 3,5-dimethylphenol, 2,4,6-trimethylphenol and ( E,Z)- and ( E,E)-2,4-hexadienedial). The UV absorption cross sections reported here can be used for the evaluation of DOAS spectra (Differential Optical Absorption Spectroscopy) for measurements of the above compounds in the atmosphere and in reaction chambers, while the IR absorption cross sections will primarily be useful in laboratory studies on atmospheric chemistry, where FT-IR spectrometry is an important tool.

  4. Review of an assortment of IR materials-devices technologies used for imaging in spectral bands ranging from the visible to very long wavelengths

    Science.gov (United States)

    DeWames, Roger E.

    2016-05-01

    In this paper we review the intrinsic and extrinsic technological properties of the incumbent technology, InP/In0.53Ga0.47As/InP, for imaging in the visible- short wavelength spectral band, InSb and HgCdTe for imaging in the mid-wavelength spectral band and HgCdTe for imaging in the long wavelength spectral band. These material systems are in use for a wide range of applications addressing compelling needs in night vision imaging, low light level astronomical applications and defense strategic satellite sensing. These materials systems are direct band gap energy semiconductors hence the internal quantum efficiency η, is near unity over a wide spectral band pass. A key system figure of merit of a shot noise limited detector technology is given by the equation (1+Jdark. /Jphoton), where Jdark is the dark current density and Jphoton ~qηΦ is the photocurrent density; Φ is the photon flux incident on the detector and q is the electronic charge. The capability to maintain this factor for a specific spectral band close to unity for low illumination conditions and low temperature onset of non-ideal dark current components, basically intrinsic diffusion limited performance all the way, is a marker of quality and versatility of a semiconductor detector technology. It also enables the highest temperature of operation for tactical illumination conditions. A purpose of the work reported in this paper is to explore the focal plane array data sets of photodiode detector technologies widely used to bench mark their fundamental and technology properties and identify paths for improvements.

  5. Digital image multiplexing/demultiplexing method using spatial spectral diffusion and virtual phase conjugation technique for reduction of dynamic range consumption in holographic medium

    Science.gov (United States)

    Goto, Yuta; Okamoto, Atsushi; Takabayashi, Masanori; Ogawa, Kazuhisa; Tomita, Akihisa

    2017-09-01

    The recording density in holographic data storage (HDS) systems is determined by the dynamic range of the recording medium. If a hologram is recorded with a small exposure, the consumption amount of the dynamic range per hologram is reduced, and the recording density can be improved. In this report, we propose a digital image multiplexing/demultiplexing method using spatial spectral diffusion and a virtual phase conjugation technique to reduce the consumption amount of the dynamic range in a recording medium. In our method, multiple signals are simultaneously recorded in a medium by multiplexing those signals using a beam combiner before recording, unlike the general multiplexing method of HDS. Then, each original signal can be reproduced independently by utilizing the property of a random diffuser and a phase-conjugated light. In the simulation, we confirmed that our method can improve the recording density because the consumption of the dynamic range is reduced.

  6. Study of wave chaos in a randomly-inhomogeneous oceanic acoustic waveguide: spectral analysis of the finite-range evolution operator

    CERN Document Server

    Makarov, D V; Uleysky, M Yu; Petrov, P S

    2012-01-01

    The proplem of sound propagation in an oceanic waveguide is considered. Scattering on random inhomogeneity of the waveguide leads to wave chaos. Chaos reveals itself in spectral properties of the finite-range evolution operator (FREO). FREO describes transformation of a wavefield in course of propagation along a finite segment of a waveguide. We study transition to chaos by tracking variations in spectral statistics with increasing length of the segment. Analysis of the FREO is accompanied with ray calculations using the one-step Poincar\\'e map which is the classical counterpart of the FREO. Underwater sound channel in the Sea of Japan is taken for an example. Several methods of spectral analysis are utilized. In particular, we approximate level spacing statistics by means of the Berry-Robnik and Brody distributions, explore the spectrum using the procedure elaborated by A. Relano with coworkers (Relano et al, Phys. Rev. Lett., 2002; Relano, Phys. Rev. Lett., 2008), and analyze modal expansions of the eigenfu...

  7. Single-shot high-dynamic range laser pulse contrast measurement using Fourth-Order-Crosscorrelation via Self-Referenced-Spectral-Interferometry (FOX-SRSI)

    CERN Document Server

    Palaniyappan, Sasi; Shimada, T; Shah, R C; Jung, D; Gautier, D C; Hegelich, B M; Fernandez, J C

    2012-01-01

    High-dynamic range isolation of the interference term and the non-interference term in the inverse Fourier-transformed spectral interferogram as required in Self-Referenced-Spectral-Interferometry (SRSI) for single-shot high-dynamic range laser pulse characterization is not always practically possible due to presence of the non-interference term over the entire temporal widow. Alternatively, we propose and demonstrate that one could directly obtain the single-shot Fourth-Order-Crosscorrelation (FOX) of the laser pulse to be characterized via SRSI (FOX-SRSI) from the interference term as the high-dynamic range laser contrast measurement, avoiding the need to isolate the interference and non-interference terms. As a consequence, the undesired contribution from the non-interference term limits the valid temporal window of the measurement. The single-shot FOX-SRSI result is consistent with the laser contrast measured independently using a multi-shot scanning third-order autocorrelator.

  8. Ultrawideband coherent noise lidar range-Doppler imaging and signal processing by use of spatial-spectral holography in inhomogeneously broadened absorbers.

    Science.gov (United States)

    Li, Youzhi; Hoskins, Alan; Schlottau, Friso; Wagner, Kelvin H; Embry, Carl; Babbitt, William Randall

    2006-09-01

    We introduce a new approach to coherent lidar range-Doppler sensing by utilizing random-noise illuminating waveforms and a quantum-optical, parallel sensor based on spatial-spectral holography (SSH) in a cryogenically cooled inhomogeneously broadened absorber (IBA) crystal. Interference between a reference signal and the lidar return in the spectrally selective absorption band of the IBA is used to sense the lidar returns and perform the front-end range-correlation signal processing. Modulating the reference by an array of Doppler compensating frequency shifts enables multichannel Doppler filtering. This SSH sensor performs much of the postdetection signal processing, increases the lidar system sensitivity through range-correlation gain before detection, and is capable of not only Doppler processing but also parallel multibeam reception using the high-spatial resolution of the IBA crystals. This approach permits the use of ultrawideband, high-power, random-noise, cw lasers as ranging waveforms in lidar systems instead of highly stabilized, injection-seeded, and amplified pulsed or modulated laser sources as required by most conventional coherent lidar systems. The capabilities of the IBA media for many tens of gigahertz bandwidth and resolution in the 30-300 kHz regime, while using either a pseudo-noise-coded waveform or just a high-power, noisy laser with a broad linewidth (e.g., a truly random noise lidar) may enable a new generation of improved lidar sensors and processors. Preliminary experimental demonstrations of lidar ranging and simulation on range-Doppler processing are presented.

  9. Monolithic integration of InGaN segments emitting in the blue, green, and red spectral range in single ordered nanocolumns

    Energy Technology Data Exchange (ETDEWEB)

    Albert, S.; Bengoechea-Encabo, A.; Sanchez-Garcia, M. A.; Calleja, E. [ISOM and Dept. Ingenieria Electronica, ETSI Telecomunicacion, Universidad Politecnica de Madrid, Ciudad Universitaria s/n, 28040 Madrid (Spain); Kong, X.; Trampert, A. [Paul-Drude-Institut fuer Festkoeperelektronik, Hausvogteiplatz 5-7, 10117 Berlin (Germany)

    2013-05-06

    This work reports on the selective area growth by plasma-assisted molecular beam epitaxy and characterization of InGaN/GaN nanocolumnar heterostructures. The optimization of the In/Ga and total III/V ratios, as well as the growth temperature, provides control on the emission wavelength, either in the blue, green, or red spectral range. An adequate structure tailoring and monolithic integration in a single nanocolumnar heterostructure of three InGaN portions emitting in the red-green-blue colors lead to white light emission.

  10. Validation of HITEMP-2010 for carbon dioxide and water vapour at high temperatures and atmospheric pressures in 450-7600cm-1 spectral range

    DEFF Research Database (Denmark)

    Alberti, Michael; Weber, Roman; Mancini, Marco

    2015-01-01

    The objective of the work is validation of HITEMP-2010 at atmospheric pressures and temperatures reaching 1770K. To this end, spectral transmissivities at 1cm-1 resolution and excellent signal-to-noise-ratio have been measured for 22 CO2/H2O/N2 mixtures. In this paper we consider the 450cm-1-7600...... absorption lines listed in HITEMP-2010 have not been observed in the measured spectra and/or are wrongly scaled with temperature. The complete (there are no missing bands) spectra spanning the 450-7600cm-1 range are appended as Supplementary Material....

  11. Monolithic integration of InGaN segments emitting in the blue, green, and red spectral range in single ordered nanocolumns

    Science.gov (United States)

    Albert, S.; Bengoechea-Encabo, A.; Kong, X.; Sanchez-Garcia, M. A.; Calleja, E.; Trampert, A.

    2013-05-01

    This work reports on the selective area growth by plasma-assisted molecular beam epitaxy and characterization of InGaN/GaN nanocolumnar heterostructures. The optimization of the In/Ga and total III/V ratios, as well as the growth temperature, provides control on the emission wavelength, either in the blue, green, or red spectral range. An adequate structure tailoring and monolithic integration in a single nanocolumnar heterostructure of three InGaN portions emitting in the red-green-blue colors lead to white light emission.

  12. Plasmonic resonances in hybrid systems of aluminum nanostructured arrays and few layer graphene within the UV-IR spectral range.

    Science.gov (United States)

    González-Campuzano, Ricardo; Saniger, J M; Mendoza, Doroteo

    2017-09-15

    The size-controllable and ordered Al nanocavities and nanodomes arrays were synthesized by electrochemical anodization of aluminum using phosphoric acid, citric acid and mixture both acids. Few layer graphene (FLG) was transferred directly on top of Al nanostructures and their morphology were evaluated by Scanning Electron Microscopy. The interaction between FLG and the plasmonic properties of Al nanostructures arrays were investigated based on specular reflectivity in the UV-Vis-IR range and Raman Spectroscopy. We found that their optical reflectivity was dramatically reduced as compared with unstructured Al. At the same time pronounced reflectivity dips were detectable in the 200 nm-896 nm wavelength range, which were ascribed to plasmonic resonances. The plasmonic properties of these nanostructures do not exhibit evident changes by the presence of FLG in the UV-Vis range of the electromagnetic spectrum. By contrast, the Surface-Enhanced Raman Spectroscopy (SERS) of FLG was observed in nanocavities and nanodomes structures that result in an intensity increase of the characteristic G and 2D bands of FLG induced by the plasmonic properties of Al nanostructures. © 2017 IOP Publishing Ltd.

  13. Transport Coefficients of Black M3-Branes

    CERN Document Server

    Dhuria, Mansi

    2014-01-01

    The local uplift via local SYZ mirror symmetry of (M)N (fractional)D3-branes, and wrapped N_f flavor D7-branes in the presence of a black-hole resulting in a non-Kaehler resolved warped deformed conifold (NKRWDC) in [1], was carried out in [2] and resulted in black M3-branes; the deviation from the ISD condition of G_3 proportional to the square of the resolution parameter, in the limits of [1] and MQGP limit of [2], imposed on (g_s,M,N), can be ignored [3]. The uplift, if valid globally, asymptotes to M5-branes wrapping a two-cycle (homologously an (large) integer sum of two-spheres) in AdS_5xM_6. Interestingly, in the limits of [1]/ [2], assuming the deformation > resolution, by estimating the five SU(3) structure torsion (\\tau) classes W_{1,2,3,4,5} we show that \\tau\\in W_5 in the large-r limit, implying the NKRWDC reduces to a warped Kaehler deformed conifold. Further, the local T^3 of [2] in the large-r limit and the limits of [1] and the `MQGP' limit of [2], satisfies the same conditions as the maximal ...

  14. Wide-Band Spatially Tunable Photonic Bandgap in Visible Spectral Range and Laser based on a Polymer Stabilized Blue Phase

    OpenAIRE

    2016-01-01

    This work successfully develops a largely-gradient-pitched polymer-stabilized blue phase (PSBP) photonic bandgap (PBG) device with a wide-band spatial tunability in nearly entire visible region within a wide blue phase (BP) temperature range including room temperature. The device is fabricated based on the reverse diffusion of two injected BP-monomer mixtures with a low and a high chiral concentrations and afterwards through UV-curing. This gradient-pitched PSBP can show a rainbow-like reflec...

  15. In-vivo gingival sulcus imaging using full-range, complex-conjugate-free, endoscopic spectral domain optical coherence tomography

    Science.gov (United States)

    Huang, Yong; Zhang, Kang; Yi, WonJin; Kang, Jin U.

    2012-01-01

    Frequent monitoring of gingival sulcus will provide valuable information for judging the presence and severity of periodontal disease. Optical coherence tomography, as a 3D high resolution high speed imaging modality is able to provide information for pocket depth, gum contour, gum texture, gum recession simultaneously. A handheld forward-viewing miniature resonant fiber-scanning probe was developed for in-vivo gingival sulcus imaging. The fiber cantilever driven by magnetic force vibrates at resonant frequency. A synchronized linear phase-modulation was applied in the reference arm by the galvanometer-driven reference mirror. Full-range, complex-conjugate-free, real-time endoscopic SD-OCT was achieved by accelerating the data process using graphics processing unit. Preliminary results showed a real-time in-vivo imaging at 33 fps with an imaging range of lateral 2 mm by depth 3 mm. Gap between the tooth and gum area was clearly visualized. Further quantification analysis of the gingival sulcus will be performed on the image acquired.

  16. Sensitivity gains, linearity, and spectral reproducibility in nonuniformly sampled multidimensional MAS NMR spectra of high dynamic range

    Science.gov (United States)

    Suiter, Christopher L.; Paramasivam, Sivakumar; Hou, Guangjin; Sun, Shangjin; Rice, David; Hoch, Jeffrey C.; Rovnyak, David

    2014-01-01

    Recently, we have demonstrated that considerable inherent sensitivity gains are attained in MAS NMR spectra acquired by nonuniform sampling (NUS) and introduced maximum entropy interpolation (MINT) processing that assures the linearity of transformation between the time and frequency domains. In this report, we examine the utility of the NUS/MINT approach in multidimensional datasets possessing high dynamic range, such as homonuclear 13C–13C correlation spectra. We demonstrate on model compounds and on 1–73-(U-13C, 15N)/74–108-(U-15N) E. coli thioredoxin reassembly, that with appropriately constructed 50 % NUS schedules inherent sensitivity gains of 1.7–2.1-fold are readily reached in such datasets. We show that both linearity and line width are retained under these experimental conditions throughout the entire dynamic range of the signals. Furthermore, we demonstrate that the reproducibility of the peak intensities is excellent in the NUS/MINT approach when experiments are repeated multiple times and identical experimental and processing conditions are employed. Finally, we discuss the principles for design and implementation of random exponentially biased NUS sampling schedules for homonuclear 13C–13C MAS correlation experiments that yield high-quality artifact-free datasets. PMID:24752819

  17. Sensitivity Gains, Linearity, and Spectral Reproducibility in Nonuniformly Sampled Multidimensional MAS NMR Spectra of High Dynamic Range.

    Energy Technology Data Exchange (ETDEWEB)

    Suiter, Christopher L.; Paramasivam, Sivakumar; Hou, Guangjin; Sun, Shangjin; Rice, David M.; Hoch, Jeffrey C.; Rovnyak, David S.; Polenova, Tatyana E.

    2014-04-22

    Recently, we have demonstrated that considerable inherent sensitivity gains are attained in MAS NMR spectra acquired by nonuniform sampling (NUS) and introduced maximum entropy interpolation (MINT) processing that assures the linearity of transformation between the time and frequency domains. In this report, we examine the utility of the NUS/MINT approach in multidimensional datasets possessing high dynamic range, such as homonuclear 13C–13C correlation spectra. We demonstrate on model compounds and on 1–73-(U-13C,15N)/74–108-(U-15N) E. coli thioredoxin reassembly, that with appropriately constructed 50 % NUS schedules inherent sensitivity gains of 1.7–2.1-fold are readily reached in such datasets. We show that both linearity and line width are retained under these experimental conditions throughout the entire dynamic range of the signals. Furthermore, we demonstrate that the reproducibility of the peak intensities is excellent in the NUS/MINT approach when experiments are repeated multiple times and identical experimental and processing conditions are employed. Finally, we discuss the principles for design and implementation of random exponentially biased NUS sampling schedules for homonuclear 13C–13C MAS correlation experiments that yield high quality artifact-free datasets.

  18. Spectral evolution of star clusters in the Large Magellanic Cloud: I. Blue concentrated clusters in the age range 40-300 Myr

    CERN Document Server

    Santos, J F C; Ahumada, A V; Bica, E; Piatti, A E; Parisi, M C

    2005-01-01

    Integrated spectroscopy of a sample of 17 blue concentrated Large Magellanic Cloud (LMC) clusters is presented and its spectral evolution studied. The spectra span the range ~3600-6800A with a resolution of ~14A FWHM, being used to determine cluster ages and, in connection with their spatial distribution, to explore the LMC structure and cluster formation history. Cluster reddening values were estimated by interpolation, using the available extinction maps. We used two methods to derive cluster ages: (i) template matching, in which line strengths and continuum distribution of the cluster spectra were compared and matched to those of template clusters with known astrophysical properties, and (ii) equivalent width (EW) method, in which new age/metallicity calibrations were used together with diagnostic diagrams involving the sum of EWs of selected spectral lines (KCaII, G band (CH), MgI, Hdelta, Hgamma and Hbeta). The derived cluster ages range from 40Myr (NGC2130 and SL237) to 300Myr (NGC1932 and SL709), a goo...

  19. Polylogarithmic representation of radiative and thermodynamic properties of thermal radiation in a given spectral range: I. Blackbody radiation

    CERN Document Server

    Fisenko, Anatoliy I

    2014-01-01

    Using polylogarithm functions the exact analytical expressions for the radiative and thermodynamic properties of blackbody radiation, such as the Wien displacement law, Stefan-Boltzmann law, total energy density, number density of photons, Helmholtz free energy density, internal energy density, enthalpy density, entropy density, heat capacity at constant volume, and pressure in the finite range of frequencies are constructed. The obtained expressions allow us to tabulate these functions in various finite frequency bands at different temperatures for practical applications. As an example, the radiative and thermodynamic functions using experimental data for the monopole spectrum of the Cosmic Microwave Background (CMB) radiation measured by the COBE FIRAS instrument in the 60 - 600 GHz frequency interval at the temperature T = 2.725 K are calculated. The expressions obtained for the radiative and thermodynamic functions can be easily presented in wavelength and wavenumber domains.

  20. Graphitic Csub>3sub>Nsub>4sub> as a new saturable absorber for the mid-infrared spectral range.

    Science.gov (United States)

    Fan, Mingqi; Li, Tao; Li, Guiqiu; Ma, Houyi; Zhao, Shengzhi; Yang, Kejian; Kränkel, Christian

    2017-01-15

    The saturable absorption properties of few-layer graphitic carbon nitride (g-Csub>3sub>Nsub>4sub>) nanosheets near 3 μm were investigated. A stable Q-switched Er:Lusub>2sub>Osub>3sub> laser at 2.84 μm was realized by using a home-made g-Csub>3sub>Nsub>4sub> saturable absorber (SA), generating a pulse duration of 351 ns and an average output power of 1.09 W at a repetition rate of 99 kHz, corresponding to a pulse energy of 11.1 μJ. Our result indicates a great potential of g-Csub>3sub>Nsub>4sub> as a new SA in the 3 μm wavelength range.

  1. High resolution spectral survey of symbiotic stars in the near-IR over the GAIA wavelength range

    CERN Document Server

    Marrese, P M; Munari, U; Marrese, Paola M.; Sordo, Rosanna; Munari, Ulisse

    2002-01-01

    High resolution (R~20,000), high signal-to-noise (S/N~100) spectra were collected for ~40 symbiotic stars with the Asiago echelle spectrograph over the same 8480-8740 Ang wavelength range covered by the ESA Cornerstone mission GAIA, centered on the near-IR CaII triplet and the head of the Paschen series. A large number (~140) of cool MKK giant and supergiant templates were observed with the same instrumentation to serve as a reference and classification grid. The spectra offer bright prospects in classifying and addressing the nature of the cool component of symbiotic stars (deriving T(eff), log g, [Fe/H], [alpha/Fe], V(rot)sin i both via MDM-like methods and syntetic atmosphere modeling) and mapping the physical condition and kinematics of the gas regions responsible for the emission lines.

  2. Optimization of cubic GaN/AlGaN quantum well-based structures for intersubband absorption in the infrared spectral range

    Science.gov (United States)

    Radosavljević, Ana; Radovanović, Jelena; Milanović, Vitomir

    2014-03-01

    A method is proposed for the optimization of structural parameters of GaN/AlGaN quantum wells and Bragg-confined structures, with respect to peak intersubband absorption from the ground to the first excited electronic state in the mid and near infrared spectral range. It is based on the application of the Genetic Algorithm and delivers globally optimal structures with a preset number of embedded layers. Simple rectangular quantum well profile is investigated for the maximal Stark effect and applications to tunable mid-infrared photodetectors. In case of Bragg-confined structures, an above the barrier bound state is used to extend the range of transition energies above the values available in conventional quantum wells. The effects of band nonparabolicity are taken into account.

  3. Enhanced optical transmission through a star-shaped bull's eye at dual resonant-bands in UV and the visible spectral range.

    Science.gov (United States)

    Nazari, Tavakol; Khazaeinezhad, Reza; Jung, Woohyun; Joo, Boram; Kong, Byung-Joo; Oh, Kyunghwan

    2015-07-13

    Dual resonant bands in UV and the visible range were simultaneously observed in the enhanced optical transmission (EOT) through star-shaped plasmonic structures. EOTs through four types of polygonal bull's eyes with a star aperture surrounded by the concentric star grooves were analyzed and compared for 3, 4, 5, and 6 corners, using finite difference time domain (FDTD) method. In contrast to plasmonic resonances in the visible range, the UV-band resonance intensity was found to scale with the number of corners, which is related with higher order multipole interactions. Spectral positions and relative intensities of the dual resonances were analyzed parametrically to find optimal conditions to maximize EOT in UV-visible dual bands.

  4. Simulation of laser propagation through a three-layer human skin model in the spectral range from 1000 to 1900 nm

    Science.gov (United States)

    Nasouri, Babak; Murphy, Thomas E.; Berberoglu, Halil

    2014-07-01

    For understanding the mechanisms of low-level laser/light therapy (LLLT), accurate knowledge of light interaction with tissue is necessary. We present a three-dimensional, multilayer reduced-variance Monte Carlo simulation tool for studying light penetration and absorption in human skin. Local profiles of light penetration and volumetric absorption were calculated for uniform as well as Gaussian profile beams with different spreads over the spectral range from 1000 to 1900 nm. The results showed that lasers within this wavelength range could be used to effectively and safely deliver energy to specific skin layers as well as achieve large penetration depths for treating deep tissues, without causing skin damage. In addition, by changing the beam profile from uniform to Gaussian, the local volumetric dosage could increase as much as three times for otherwise similar lasers. We expect that this tool along with the results presented will aid researchers in selecting wavelength and laser power in LLLT.

  5. Spectral studies of SiCl4 + N2O + Ar and SiH4 + Ar mixtures in a shock tube in 160-550 nm range

    Science.gov (United States)

    Park, C.; Fujiwara, T.

    1978-01-01

    Gases containing SiO, SiO2, SiH, and Si2 were produced in the reflected-shock region of a shock tube by heating SiCl4 + N2O + Ar and SiH4 + Ar mixtures with shock waves. Spectral absorption characteristics were measured in the 160-550 nm wavelength range and in the 2800-3600 K temperature range and compared to calculated values. The sums of the squares of electronic transition moments at equilibrium separation were derived. It was found that absorption by SiO2 and other known bands of SiO, SiH, and Si2 were too weak to be measured. The cross section of absorption by a continuum, believed due to SiH, varied from 2.5 x 10 to the -17th sq cm at 280 nm to 1.6 x 10 to the -18th sq cm at 440 nm.

  6. Simulation of laser propagation through a three-layer human skin model in the spectral range from 1000 to 1900 nm.

    Science.gov (United States)

    Nasouri, Babak; Murphy, Thomas E; Berberoglu, Halil

    2014-01-01

    For understanding the mechanisms of low-level laser/light therapy (LLLT), accurate knowledge of light interaction with tissue is necessary. We present a three-dimensional, multilayer reduced-variance Monte Carlo simulation tool for studying light penetration and absorption in human skin. Local profiles of light penetration and volumetric absorption were calculated for uniform as well as Gaussian profile beams with different spreads over the spectral range from 1000 to 1900 nm. The results showed that lasers within this wavelength range could be used to effectively and safely deliver energy to specific skin layers as well as achieve large penetration depths for treating deep tissues, without causing skin damage. In addition, by changing the beam profile from uniform to Gaussian, the local volumetric dosage could increase as much as three times for otherwise similar lasers. We expect that this tool along with the results presented will aid researchers in selecting wavelength and laser power in LLLT.

  7. New BMW M3 sports coupe; Neues Sportcoupe M3 von BMW

    Energy Technology Data Exchange (ETDEWEB)

    Biermann, A.; Friedmann, S.; Gehrig, H.; Huebner, W.; Weidhase, U. [Bayerische Motoren Werke AG (BMW), Muenchen (Germany); Koplenig, W. [BMW, Muenchen (Germany). Fachbereich Karosserie

    2000-10-01

    Since 1972 Motorsport (which has been known as BMW M since 1994) has been manufacturing automobiles of exceptionally sporting character on the basis of suitable series-production cars. With its new M3, BMW M continues this tradition. It is a sports coupe based on the latest BMW 3 Series model line. Its sports design embodies the essentials of BMW M's performance philosophy. Both visible and invisible 'highlights' such as the new high-speed driveline rating elevate its longitudinal and lateral driving dynamics to the level of a racing car. We have also succeeded in maintaining the basic car's unlimited suitability for everyday use. The new M3 is therefore a fully-fledged sports car without the typical disadvantages of this type of vehicle. (orig.) [German] Bereits seit 1972 entstehen bei BMW Motorsport (seit 1994 BMW M) auf der Basis von Serienfahrzeugen Automobile mit aussergewoehnlichen sportlichen Eigenschaften. Mit dem neuen M3, abgeleitet von der aktuellen BMW Dreier-Reihe, setzt BMW M diese Tradition fort. Das Sportcoupe erschliesst ueber die weiterentwickelte Hochdrehzahlauslegung eine Fahrdynamik in Laengs- und Querrichtung auf dem Niveau eines Rennsportwagens. Gleichzeitig ist es gelungen, die uneingeschraenkte Alltagstauglichkeit des Basis-Fahrzeugs zu erhalten. Der neue M3 ist somit ein vollwertiger Sportwagen, vermeidet aber dessen typische Nachteile. (orig.)

  8. Narrow-line external cavity diode laser micro-packaging in the NIR and MIR spectral range

    Science.gov (United States)

    Jiménez, A.; Milde, T.; Staacke, N.; Aßmann, C.; Carpintero, G.; Sacher, J.

    2017-07-01

    Narrow-linewidth tunable diode lasers are an important tool for spectroscopic instrumentation. Conventional external cavity diode lasers offer high output power and narrow linewidth. However, most external cavity diode lasers are designed as laboratory instrument and do not allow portability. In comparison, other commonly used lasers, like distributed feedback lasers (DFB) that are capable of driving a handheld device, are limited in power and show linewidths which are not sufficiently narrow for certain applications. We present new miniaturized types of tunable external cavity diode laser which overcome the drawbacks of conventional external cavity diode lasers and which preserve the advantages of this laser concept. Three different configurations are discussed in this article. The three types of miniaturized external cavity diode laser systems achieve power values of more than 50 mW within the 1.4 μm water vapor absorption band with excellent side-mode suppression and linewidth below 100 kHz. Typical features outstand with respect to other type of laser systems which are of extended use such as DFB laser diodes. The higher output power and the lower linewidth will enable a higher sensitivity and resolution for a wide range of applications.

  9. The potential for extending the spectral range accessible to the European XFEL down to 0.05 nm

    CERN Document Server

    Geloni, Gianluca; Saldin, Evgeni

    2010-01-01

    Specifications of the European XFEL cover a range of wavelengths down to 0.1 nm. The baseline design of the European XFEL assumes standard (SASE) FEL mode for production of radiation i.e. only one photon beam at one fixed wavelength from each baseline undulator with tunable gap. Recent developments in the field of FEL physics and technology form a reliable basis for an extensions of the mode of operation of XFEL facilities. This paper explores how the wavelength of the output radiation can be decreased well beyond the European XFEL design, down to 0.05 nm. In the proposed scheme, which is based on the use "fresh bunch" technique, simultaneous operation at two different wavelengths possible. It is shown that one can generate simultaneously, in the same baseline undulator with tunable gap, high intensity radiation at 0.05 nm at saturation, and high intensity radiation around 0.15 nm according to design specifications. We present a feasibility study and we make exemplifications with the parameters of SASE2 line ...

  10. Large-Scale Structure of the Molecular Gas in Taurus Revealed by High Linear Dynamic Range Spectral Line Mapping

    CERN Document Server

    Goldsmith, Paul F; Narayanan, Gopal; Snell, Ronald; Li, Di; Brunt, Chris

    2008-01-01

    We report the results of a 100 square degree survey of the Taurus Molecular Cloud region in the J = 1-0 transition of 12CO and 13CO. The image of the cloud in each velocity channel includes ~ 3 million Nyquist sampled pixels on a 20" grid. The high sensitivity and large linear dynamic range of the maps in both isotopologues reveal a very complex, highly structured cloud morphology. There are large scale correlated structures evident in 13CO emission having very fine dimensions, including filaments, cavities, and rings. The 12CO emission shows a quite different structure, with particularly complex interfaces between regions of greater and smaller column density defining the boundaries of the largest-scale cloud structures. The axes of the striations seen in the 12CO emission from relatively diffuse gas are aligned with the direction of the magnetic field. Using a column density-dependent model for the CO fractional abundance, we derive the mass of the region mapped to be 24,000 solar masses, a factor of three ...

  11. Spectral Modulation Effect in Teleseismic P-waves from North Korean Nuclear Tests Recorded in Broad Azimuthal Range and Possible Source Depth Estimation

    Science.gov (United States)

    Gitterman, Y.; Kim, S. G.; Hofstetter, R.

    2016-04-01

    Three underground nuclear explosions, conducted by North Korea in 2006, 2009 and 2013, are analyzed. The last two tests were recorded by the Israel Seismic Network. Pronounced coherent minima (spectral nulls) at 1.2-1.3 Hz were revealed in the spectra of teleseismic P -waves. For a ground-truth explosion with a shallow source depth, this phenomenon can be interpreted in terms of the interference between the down-going P-wave and the pP phase reflected from the Earth's surface. This effect was also observed at ISN stations for a Pakistan nuclear explosion at a different frequency 1.7 Hz and the PNE Rubin-2 in West Siberia at 1 Hz, indicating a source-effect and not a site-effect. Similar spectral minima having essentially the same frequency, as at ISN, were observed in teleseismic P-waves for all the three North Korean explosions recorded at networks and arrays in Kazakhstan (KURK), Norway (NNSN), Australia (ASAR, WRA) and Canada (YKA), covering a broad azimuthal range. Data of 2009 and 2013 tests at WRA and KURK arrays showed harmonic spectral modulation with three multiple minima frequencies, evidencing the clear interference effect. These observations support the above-mentioned interpretation. Based on the null frequency dependency on the near-surface acoustic velocity and the source depth, the depth of the North Korean tests was estimated about 2.0-2.1 km. It was shown that the observed null frequencies and the obtained source depth estimates correspond to P- pP interference phenomena in both cases of a vertical shaft or a horizontal drift in a mountain. This unusual depth estimation needs additional validation based on more stations and verification by other methods.

  12. The potential for extending the spectral range accessible to the european X-ray free electron laser in the direction of longer wavelengths

    CERN Document Server

    Saldin, E L; Yurkov, M V

    2004-01-01

    The baseline specifications of European XFEL give a range of wavelengths between 0.1 nm and 2 nm. This wavelength range at fixed electron beam energy 17.5 GeV can be covered by operating the SASE FEL with three undulators which have different period and tunable gap. A study of the potential for the extending the spectral range accessible to the XFEL in the direction of longer wavelengths is presented. The extension of the wavelength range to 6 nm would be cover the water window in the VUV region, opening the facility to a new class of experiments. There are at least two possible sources of VUV radiation associated with the X-ray FEL; the "low (2.5 GeV) energy electron beam dedicated" and the " 17.5 GeV spent beam parasitic" (or "after-burner") source modes. The second alternative, "after-burner undulator" is the one we regard as most favorable. It is possible to place an undulator as long as 80 meters after 2 nm undulator. Ultimately, VUV undulator would be able to deliver output power approaching 100 GW. A b...

  13. Empirical classification of VLT/Giraffe stellar spectra in the wavelength range 6440-6810 A in the gamma Vel cluster, and calibration of spectral indices

    CERN Document Server

    Damiani, F; Micela, G; Randich, S; Gilmore, G; Drew, J E; Jeffries, R D; Frémat, Y; Alfaro, E J; Bensby, T; Bragaglia, A; Flaccomio, E; Lanzafame, A C; Pancino, E; Recio-Blanco, A; Sacco, G G; Smiljanic, R; Jackson, R J; de Laverny, P; Morbidelli, L; Worley, C C; Hourihane, A; Costado, M T; Jofré, P; Lind, K; Maiorca, E

    2014-01-01

    We study spectral diagnostics available from optical spectra with R=17000 obtained with the VLT/Giraffe HR15n setup, using observations from the Gaia-ESO Survey, on the gamma Vel young cluster, in order to determine the fundamental parameters of these stars. We define a set of spectroscopic indices, sampling TiO bands, H-alpha core and wings, and many temperature- and gravity-sensitive lines. Combined indices tau (gamma) are also defined as Teff (log g) indicators over a wide spectral-type range. H-alpha emission-line indices are also chromospheric activity or accretion indicators. A metallicity-sensitive index is also defined. These indices enable us to find a clear difference between gravities of main-sequence and pre-main-sequence stars (as well as giant stars): the (gamma,tau) diagram is thus argued to be a promising distance-independent age measurement tool for young clusters. Our indices were quantitatively calibrated by means of photometry and literature reference spectra (from UVES-POP and ELODIE 3.1 ...

  14. The Herschel/HIFI spectral survey of OMC-2 FIR 4 (CHESS): An overview of the 480 to 1902 GHz range

    CERN Document Server

    Kama, M; Dominik, C; Ceccarelli, C; Fuente, A; Caux, E; Higgins, R; Tielens, A G G M; Alonso-Albi, T

    2013-01-01

    Broadband spectral surveys of protostars offer a rich view of the physical, chemical and dynamical structure and evolution of star-forming regions. The Herschel Space Observatory opened up the terahertz regime to such surveys, giving access to the fundamental transitions of many hydrides and to the high-energy transitions of many other species. A comparative analysis of the chemical inventories and physical processes and properties of protostars of various masses and evolutionary states is the goal of the Herschel CHEmical Surveys of Star forming regions (CHESS) key program. This paper focusses on the intermediate-mass protostar, OMC-2 FIR 4. We obtained a spectrum of OMC-2 FIR 4 in the 480 to 1902 GHz range with the HIFI spectrometer onboard Herschel and carried out the reduction, line identification, and a broad analysis of the line profile components, excitation, and cooling. We detect 719 spectral lines from 40 species and isotopologs. The line flux is dominated by CO, H2O, and CH3OH. The line profiles ar...

  15. Low-Loss Coupling of Quantum Cascade Lasers into Hollow-Core Waveguides with Single-Mode Output in the 3.7–7.6 μm Spectral Range

    Directory of Open Access Journals (Sweden)

    Pietro Patimisco

    2016-04-01

    Full Text Available We demonstrated low-loss and single-mode laser beam delivery through hollow-core waveguides (HCWs operating in the 3.7–7.6 μm spectral range. The employed HCWs have a circular cross section with a bore diameter of 200 μm and metallic/dielectric internal coatings deposited inside a glass capillary tube. The internal coatings have been produced to enhance the spectral response of the HCWs in the range 3.5–12 µm. We demonstrated Gaussian-like outputs throughout the 4.5–7.6 µm spectral range. A quasi single-mode output beam with only small beam distortions was achieved when the wavelength was reduced to 3.7 μm. With a 15-cm-long HCW and optimized coupling conditions, we measured coupling efficiencies of >88% and transmission losses of <1 dB in the investigated infrared spectral range.

  16. Shock-tube studies of atomic silicon emission in the spectral range 180 to 300 nm. [environment simulation for Jupiter probes

    Science.gov (United States)

    Prakash, S. G.; Park, C.

    1978-01-01

    Emission spectroscopy of shock-heated atomic silicon was performed in the spectral range 180 to 300 nm, in an environment simulating the ablation layer expected around a Jovian entry probe with a silica heat shield. From the spectra obtained at temperatures from 6000 to 10,000 K and electron number densities from 1 quadrillion to 100 quadrillion per cu cm, the Lorentzian line-widths were determined. The results showed that silicon lines are broadened significantly by both electrons (Stark broadening) and hydrogen atoms (Van der Waals broadening), and the combined line-widths are much larger than previously assumed. From the data, the Stark and the Van der Waals line-widths were determined for 34 silicon lines. Radiative transport through a typical shock layer was computed using the new line-width data. The computations showed that silicon emission in the hot region is large, but it is mostly absorbed in the colder region adjacent to the wall.

  17. (In,Ga,Al)P–GaP laser diodes grown on high-index GaAs surfaces emitting in the green, yellow and bright red spectral range

    Science.gov (United States)

    Ledentsov, N. N.; Shchukin, V. A.; Shernyakov, Yu M.; Kulagina, M. M.; Payusov, A. S.; Gordeev, N. Yu; Maximov, M. V.; Cherkashin, N. A.

    2017-02-01

    We report on low threshold current density (region. Extended waveguide concept results in a vertical beam divergence with a full width at half maximum of 15° for (611)A substrates. The lasing at the wavelength of 569 nm is realized at 85 K. In an orange–red laser diode structure low threshold current density (190 A cm‑2) in the orange spectral range (598 nm) is realized at 85 K. The latter devices demonstrated room temperature lasing at 628 nm at ∼2 kA cm‑2 and a total power above 3 W. The red laser diodes grown on (211)A substrates demonstrated a far field characteristic for vertically multimode lasing indicating a lower optical confinement factor for the fundamental mode as compared to the devices grown on (611)A. However, as expected from previous research, the temperature stability of the threshold current and the wavelength stability were significantly higher for (211)A-grown structures.

  18. The spectral characteristics of Gd sub 2 SiO sub 5 :Eu sup 3 sup + in VUV-UV range

    CERN Document Server

    Chen Yong; Wei Ya Guang; Tao Ye

    2002-01-01

    Synchrotron radiation source was used to investigated the spectral characteristics of Gd sub 2 SiO sub 5 :Eu sup 3 sup + in VUV-UV range. The various energy transfers at room temperature and 10 K, including from host or Gd sup 3 sup + ions to Eu sup 3 sup + ions and transfer between Eu sup 3 sup + ions at two different lattice sites, were discussed. In addition the emission spectra under 186 nm and 276 nm excitation were compared from the view of quantum cutting. The results indicate that Gd sub 2 SiO sub 5 :Eu sup 3 sup + is a kind of material with potential high efficiency quantum cutting

  19. Intersubband absorption of cubic GaN/Al(Ga)N quantum wells in the near-infrared to terahertz spectral range

    Science.gov (United States)

    Machhadani, H.; Tchernycheva, M.; Sakr, S.; Rigutti, L.; Colombelli, R.; Warde, E.; Mietze, C.; As, D. J.; Julien, F. H.

    2011-02-01

    The intersubband absorption of cubic GaN/Al(Ga)N quantum wells is studied experimentally and theoretically over a wide spectral range. By changing the quantum well thickness it is possible to tune the intersubband absorption peak wavelength from 1.4 μm (214 THz) to 63 μm (4.76 THz). Comparing the experimental results with simulations based on the effective-mass model we demonstrate that the GaN/AlN conduction-band offset is higher than 1.2 eV. The best fit with the experimental data is achieved for a conduction-band offset of 1.4 eV and for a GaN effective mass of 0.11m0.

  20. Depolarization effect in rare-earth doped Y{sub 2}O{sub 3} films in blue and UV spectral range

    Energy Technology Data Exchange (ETDEWEB)

    Gasimov, Naghi; Mammadov, Eldar; Babayev, Sardar; Mamedova, Irada; Mamedov, Nazim [Department of Ellipsometry, Institute of Physics, Azerbaijan National Academy of Sciences, H. Javid ave. 33, Baku-1143 (Azerbaijan); Joudrier, Anne L.; Andriamiadamanana, Christian; Naghavi, Negar; Guillemoles, Jean F. [Institute for Research and Development of Photovoltaic Energy, 6 Quai Watier, 78401 Chatou, Paris (France)

    2015-06-15

    The 200 to 300 nm thick, Er and Er,Yb doped Y{sub 2}O{sub 3} films deposited onto silicon substrate by spin coating have been studied by spectroscopic ellipsometry over the 192-1680 nm spectral range at room temperature. All samples have been found to be strongly depolarizing in the blue and UV part of the spectrum. Complimentary examination of the sample surfaces, using confocal photoluminescence microscopy has disclosed the non-uniform distribution of the rare-earth dopants. The depolarization effects have then been modeled and found to be best reproduced by taking the thickness non-uniformity as the main source of depolarization. The optical constants of the studied films have been determined after four-step modeling with sequential decrease of the mean square error. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  1. Light-Emitting-Diodes based on ordered InGaN nanocolumns emitting in the blue, green and yellow spectral range

    Science.gov (United States)

    Bengoechea-Encabo, A.; Albert, S.; Lopez-Romero, D.; Lefebvre, P.; Barbagini, F.; Torres-Pardo, A.; Gonzalez-Calbet, J. M.; Sanchez-Garcia, M. A.; Calleja, E.

    2014-10-01

    The growth of ordered arrays of InGaN/GaN nanocolumnar light emitting diodes by molecular beam epitaxy, emitting in the blue (441 nm), green (502 nm), and yellow (568 nm) spectral range is reported. The device active region, consisting of a nanocolumnar InGaN section of nominally constant composition and 250 to 500 nm length, is free of extended defects, which is in strong contrast to InGaN (planar) layers of similar composition and thickness. Electroluminescence spectra show a very small blue shift with increasing current (almost negligible in the yellow device) and line widths slightly broader than those of state-of-the-art InGaN quantum wells.

  2. The Herschel/HIFI spectral survey of OMC-2 FIR 4 (CHESS). An overview of the 480 to 1902 GHz range

    Science.gov (United States)

    Kama, M.; López-Sepulcre, A.; Dominik, C.; Ceccarelli, C.; Fuente, A.; Caux, E.; Higgins, R.; Tielens, A. G. G. M.; Alonso-Albi, T.

    2013-08-01

    Context. Broadband spectral surveys of protostars offer a rich view of the physical, chemical and dynamical structure and evolution of star-forming regions. The Herschel Space Observatory opened up the terahertz regime to such surveys, giving access to the fundamental transitions of many hydrides and to the high-energy transitions of many other species. Aims: A comparative analysis of the chemical inventories and physical processes and properties of protostars of various masses and evolutionary states is the goal of the Herschel CHEmical Surveys of Star forming regions (CHESS) key program. This paper focusses on the intermediate-mass protostar, OMC-2 FIR 4. Methods: We obtained a spectrum of OMC-2 FIR 4 in the 480 to 1902 GHz range with the HIFI spectrometer onboard Herschel and carried out the reduction, line identification, and a broad analysis of the line profile components, excitation, and cooling. Results: We detect 719 spectral lines from 40 species and isotopologs. The line flux is dominated by CO, H2O, and CH3OH. The line profiles are complex and vary with species and upper level energy, but clearly contain signatures from quiescent gas, a broad component likely due to an outflow, and a foreground cloud. Conclusions: We find abundant evidence for warm, dense gas, as well as for an outflow in the field of view. Line flux represents 2% of the 7 L⊙ luminosity detected with HIFI in the 480 to 1250 GHz range. Of the total line flux, 60% is from CO, 13% from H2O and 9% from CH3OH. A comparison with similar HIFI spectra of other sources is set to provide much new insight into star formation regions, a case in point being a difference of two orders of magnitude in the relative contribution of sulphur oxides to the line cooling of Orion KL and OMC-2 FIR 4. Appendix A is available in electronic form at http://www.aanda.org

  3. Spectral Aerosol Extinction (SpEx): A New Instrument for In situ Ambient Aerosol Extinction Measurements Across the UV/Visible Wavelength Range

    Science.gov (United States)

    Jordan, C. E.; Anderson, B. E.; Beyersdorf, A. J.; Corr, C. A.; Dibb, J. E.; Greenslade, M. E.; Martin, R. F.; Moore, R. H.; Scheuer, E.; Shook, M. A.; hide

    2015-01-01

    We introduce a new instrument for the measurement of in situ ambient aerosol extinction over the 300-700 nm wavelength range, the Spectral Aerosol Extinction (SpEx) instrument. This measurement capability is envisioned to complement existing in situ instrumentation, allowing for simultaneous measurement of the evolution of aerosol optical, chemical, and physical characteristics in the ambient environment. In this work, a detailed description of the instrument is provided along with characterization tests performed in the laboratory. Measured spectra of NO2 and polystyrene latex spheres agreed well with theoretical calculations. Good agreement was also found with simultaneous aerosol extinction measurements at 450, 530, and 630 nm using CAPS PMex instruments in a series of 22 tests including non-absorbing compounds, dusts, soot, and black and brown carbon analogs. SpEx can more accurately distinguish the presence of brown carbon from other absorbing aerosol due to its 300 nm lower wavelength limit compared to measurements limited to visible wavelengths. In addition, the spectra obtained by SpEx carry more information than can be conveyed by a simple power law fit that is typically defined by the use of Angstrom Exponents. Future improvements aim at lowering detection limits and ruggedizing the instrument for mobile operation.

  4. Spectral Aerosol Extinction (SpEx): A New Instrument for In situ Ambient Aerosol Extinction Measurements Across the UV/Visible Wavelength Range

    Science.gov (United States)

    Jordan, C. E.; Anderson, B. E.; Beyersdorf, A. J.; Corr, C. A.; Dibb, J. E.; Greenslade, M. E.; Martin, R. F.; Moore, R. H.; Scheuer, E.; Shook, M. A.; Thornhill, K. L.; Troop, D.; Winstead, Edward L.; Ziemba, L. D.

    2015-01-01

    We introduce a new instrument for the measurement of in situ ambient aerosol extinction over the 300-700 nm wavelength range, the Spectral Aerosol Extinction (SpEx) instrument. This measurement capability is envisioned to complement existing in situ instrumentation, allowing for simultaneous measurement of the evolution of aerosol optical, chemical, and physical characteristics in the ambient environment. In this work, a detailed description of the instrument is provided along with characterization tests performed in the laboratory. Measured spectra of NO2 and polystyrene latex spheres agreed well with theoretical calculations. Good agreement was also found with simultaneous aerosol extinction measurements at 450, 530, and 630 nm using CAPS PMex instruments in a series of 22 tests including non-absorbing compounds, dusts, soot, and black and brown carbon analogs. SpEx can more accurately distinguish the presence of brown carbon from other absorbing aerosol due to its 300 nm lower wavelength limit compared to measurements limited to visible wavelengths. In addition, the spectra obtained by SpEx carry more information than can be conveyed by a simple power law fit that is typically defined by the use of Angstrom Exponents. Future improvements aim at lowering detection limits and ruggedizing the instrument for mobile operation.

  5. Spectral Aerosol Extinction (SpEx: a new instrument for in situ ambient aerosol extinction measurements across the UV/visible wavelength range

    Directory of Open Access Journals (Sweden)

    C. E. Jordan

    2015-06-01

    Full Text Available We introduce a new instrument for the measurement of in situ ambient aerosol extinction over the 300–700 nm wavelength range, the Spectral Aerosol Extinction (SpEx instrument. This measurement capability is envisioned to complement existing in situ instrumentation, allowing for simultaneous measurement of the evolution of aerosol optical, chemical, and physical characteristics in the ambient environment. In this work, a detailed description of the instrument is provided along with characterization tests performed in the laboratory. Measured spectra of NO2 and polystyrene latex spheres (PSLs agreed well with theoretical calculations. Good agreement was also found with simultaneous aerosol extinction measurements at 450, 530, and 630 nm using CAPS PMex instruments in a series of 22 tests including non-absorbing compounds, dusts, soot, and black and brown carbon analogs. SpEx can more accurately distinguish the presence of brown carbon from other absorbing aerosol due to its 300 nm lower wavelength limit compared to measurements limited to visible wavelengths. Extinction spectra obtained with SpEx contain more information than can be conveyed by a simple power law fit (typically represented by Ångström Exponents. Planned future improvements aim to lower detection limits and ruggedize the instrument for mobile operation.

  6. Calculating 14N16O2 spectral line parameters in an infrared range: A comparison of "global" and "local" effective operator methods

    Science.gov (United States)

    Voitsekhovskaya, O. K.; Egorov, O. V.; Kashirskii, D. E.

    2016-08-01

    Nitrogen dioxide, 14N16O2, line positions and intensities calculated by us based on a "local" effective operator method are compared to the recent results of the "global" calculation. The comparison was made for theoretical absorption coefficients in the spectral range of 600-3700 cm- 1 using the measured data taken from the Pacific Northwest National Laboratory. In order to conduct the calculations, empirical parameters of the effective rotational Hamiltonian of the twenty-one vibrational states were applied from the most recent experimental works. The second order parameters of the dipole moment function of 14N16O2 were determined for the first time. The "local" line list in this research consists of one hundred and four bands and includes the line intensities of the v1 + v2 + v3 band of 14N16O2 that have not yet been investigated in the literature. Among these bands, only eleven bands are included in HITRAN2012. The reasons behind the disagreements between the theoretical and measured absorption coefficients of 14N16O2 are discussed.

  7. Luminophores of tunable colors from ternary Ag-In-S and quaternary Ag-In-Zn-S nanocrystals covering the visible to near-infrared spectral range.

    Science.gov (United States)

    Gabka, Grzegorz; Bujak, Piotr; Kotwica, Kamil; Ostrowski, Andrzej; Lisowski, Wojciech; Sobczak, Janusz W; Pron, Adam

    2017-01-04

    Ternary Ag-In-S or quaternary Ag-In-Zn-S nanocrystals were prepared from simple precursors (silver nitrate, indium(iii) chloride, zinc stearate in a mixture of DDT and ODE) by injecting a solution of elemental sulfur into OLA. Ternary nanocrystals were modified by depositing either a ZnS or a CdS shell, yielding type I and type II core/shell systems exhibiting photoluminescence QY in the range of 12-16%. Careful optimization of the reaction conditions allowed alloyed quaternary Ag-In-Zn-S nanocrystals exhibiting tunable photoluminescence in the spectral range of 520-720 nm with a QY of 48% and 59% for green and red radiations, respectively, to be obtained. (1)H NMR analysis of the nanocrystal organic shell, after dissolution of its inorganic core, indicated that surfacial sulfur atoms were covalently bonded to aliphatic chains whereas surfacial cations were coordinated by amines and carboxylate anions. No thiol-type ligands were detected. Transfer of the prepared nanocrystals to water could be achieved in one step by exchanging the initial ligands for 11-mercaptoundecanoic ones resulting in a QY value of 31%. A new Ag-In-Zn-S nanocrystal preparation method was elaborated in which indium and zinc salts of fatty acids were used as cation precursors and DDT was replaced by thioacetamide. This original DDT-free method enabled similar tuning of the photoluminescence properties of the nanocrystals as in the previous method; however the measured photoluminescence QYs were three times lower. Hence, further optimization of the new method is required.

  8. Goldschmidt crater and the Moon's north polar region: Results from the Moon Mineralogy Mapper (M3)

    Science.gov (United States)

    Cheek, L.C.; Pieters, C.M.; Boardman, J.W.; Clark, R.N.; Combe, J.-P.; Head, J.W.; Isaacson, P.J.; McCord, T.B.; Moriarty, D.; Nettles, J.W.; Petro, N.E.; Sunshine, J.M.; Taylor, L.A.

    2011-01-01

    Soils within the impact crater Goldschmidt have been identified as spectrally distinct from the local highland material. High spatial and spectral resolution data from the Moon Mineralogy Mapper (M3) on the Chandrayaan-1 orbiter are used to examine the character of Goldschmidt crater in detail. Spectral parameters applied to a north polar mosaic of M3 data are used to discern large-scale compositional trends at the northern high latitudes, and spectra from three widely separated regions are compared to spectra from Goldschmidt. The results highlight the compositional diversity of the lunar nearside, in particular, where feldspathic soils with a low-Ca pyroxene component are pervasive, but exclusively feldspathic regions and small areas of basaltic composition are also observed. Additionally, we find that the relative strengths of the diagnostic OH/H2O absorption feature near 3000 nm are correlated with the mineralogy of the host material. On both global and local scales, the strongest hydrous absorptions occur on the more feldspathic surfaces. Thus, M3 data suggest that while the feldspathic soils within Goldschmidt crater are enhanced in OH/H2O compared to the relatively mafic nearside polar highlands, their hydration signatures are similar to those observed in the feldspathic highlands on the farside. Copyright 2011 by the American Geophysical Union.

  9. Robust Satellite Techniques for monitoring earth emitted radiation in the Japanese seismic area by using MTSAT observations in the TIR spectral range

    Science.gov (United States)

    Genzano, Nicola; Filizzola, Carolina; Hattori, Katsumi; Lisi, Mariano; Paciello, Rossana; Pergola, Nicola; Tramutoli, Valerio

    2016-04-01

    Since eighties, the fluctuations of Earth's thermally emitted radiation, measured by satellite sensors operating in the thermal infrared (TIR) spectral range, have been associated with the complex process of preparation for major earthquakes. But, like other claimed earthquake precursors (seismological, physical, chemical, biological, etc.) they have been for long-time considered with some caution by scientific community. The lack of a rigorous definition of anomalous TIR signal fluctuations and the scarce attention paid to the possibility that other causes (e.g. meteorological) different from seismic activity could be responsible for the observed TIR variations were the main causes of such skepticism. Compared with previously proposed approaches the general change detection approach, named Robust Satellite Techniques (RST), showed good ability to discriminate anomalous TIR signals possibly associated to seismic activity, from the normal variability of TIR signal due to other causes. Thanks to its full exportability on different satellite packages, since 2001 RST has been implemented on TIR images acquired by polar (e.g. NOAA-AVHRR, EOS -MODIS) and geostationary (e.g. MSG-SEVIRI, NOAA-GOES/W, GMS-5/VISSR) satellite sensors, in order to verify the presence (or absence) of TIR anomalies in presence (absence) of earthquakes (with M>4) in different seismogenic areas around the world (e.g. Italy, Greece, Turkey, India, Taiwan, etc.). In this paper, the RST data analysis approach has been implemented on TIR satellite records collected over Japan by the geostationary satellite sensor MTSAT (Multifunctional Transport SATellites) and RETIRA (Robust Estimator of TIR Anomalies) index was used to identify Significant Sequences of TIR Anomalies (SSTAs) in a possible space-time relations with seismic events. Achieved results will be discussed in the perspective of a multi-parametric approach for a time-Dependent Assessment of Seismic Hazard (t-DASH).

  10. Role of Al coordination in barium phosphate glasses on the emission features of Ho{sup 3+} ion in the visible and IR spectral ranges

    Energy Technology Data Exchange (ETDEWEB)

    Satyanarayana, T.; Kalpana, T.; Ravi Kumar, V. [Department of Physics, Acharya Nagarjuna University-Nuzvid Campus, Nuzvid-521 201, A.P. (India); Veeraiah, N., E-mail: nvr8@rediffmail.co [Department of Physics, Acharya Nagarjuna University-Nuzvid Campus, Nuzvid-521 201, A.P. (India)

    2010-03-15

    The glasses of the composition (39-x)BaO-xAl{sub 2}O{sub 3}-60P{sub 2}O{sub 5}:1.0Ho{sub 2}O{sub 3} (in mol%) with x value ranging from 1.0 to 4.0 have been synthesized. The IR spectral studies of these glasses have indicated that there is a gradual transformation of Al{sup 3+} ions from tetrahedral to octahedral with increase in the concentration of Al{sub 2}O{sub 3} up to 3.0 mol%. Optical absorption and fluorescence spectra (in the visible and NIR regions) of these glasses have been recorded at room temperature. The Judd-Ofelt theory could successfully be applied to characterize the absorption and luminescence spectra of Ho{sup 3+} ions in these glasses. From the luminescence spectra, various radiative properties like transition probability A, branching ratio beta{sub r}, the radiative lifetime tau{sub r} and emission cross-section sigma{sup E} for various emission levels of these glasses have been evaluated. The radiative lifetime of the {sup 5}S{sub 2}->{sup 5}I{sub 8} (green emission) transition has also been measured. The variations observed in these parameters have been discussed in the light of varying co-ordinations (tetrahedral and octahedral positions) of Al{sup 3+} ions in the glass network. The influence of hydroxyl groups on the luminescence efficiency of the transition {sup 5}S{sub 2}->{sup 5}I{sub 8} has also been discussed. Finally the optimum concentration of Al{sub 2}O{sub 3} for getting maximum luminescence output has also been identified and reported.

  11. Genomic standards consortium workshop: metagenomics, metadata and metaanalysis (M3).

    Science.gov (United States)

    Sterk, Peter; Hirschman, Lynette; Field, Dawn; Wooley, John

    2010-01-01

    The M3 workshop has, as its primary focus, the rapidly growing area of metagenomics, including the metadata standards and the meta-analysis approaches needed to organize, process and interpret metagenomics data. The PSB Workshop builds on the first M3 meeting, a Special Interest Group (SIG) meeting at ISMB 2009, organized by the Genomics Standards Consortium.

  12. Effect of Surface Oxidization on the Spectral Normal Emissivity of Aluminum 3A21 at the Wavelength of 1.5 m Over the Temperature Range from 800 K to 910 K

    Science.gov (United States)

    Shi, Deheng; Zou, Fenghui; Wang, Shuai; Zhu, Zunlue; Sun, Jinfeng

    2015-04-01

    This study explores the dependence of the spectral emissivity on the temperature ranging from 800 K to 910 K for an oxidizing surface of aluminum 3A21. In this experiment, the infrared radiation stemming from the specimen is received by an InGaAs photodiode detector, which operates at the wavelength of 1.5 m with a bandwidth of about 20 nm. The temperature of the specimen surface is determined by averaging the two R-type platinum-rhodium thermocouples, which are tightly welded on the specimen surface. The spectral emissivity is reported before the first measurement over the temperature range from 800 K to 910 K. The variation of the spectral emissivity with the heating time is evaluated at a given temperature. The variation of the spectral emissivity with temperature is discussed for a given heating time. Oscillations of the spectral emissivity have been observed, which are affirmed to be connected with the thickness of the oxidization layer on the specimen surface, and formed by the interference effect between the radiation coming from the oxidization layer and the radiation stemming from the substrate. The effect of surface oxidization on the spectral emissivity of aluminum 3A21 is evaluated, and compared with that of SPHC steel. Analytical expressions of the spectral emissivity of aluminum 3A21 versus the temperature are derived at some given heating times. A conclusion is obtained that the experimental results obtained at a given heating time from 800 K to 910 K abide by the same functional form.

  13. Experimental Line List of Water Vapor Absorption Lines in the Spectral Ranges 1850 - 2280 CM-1 and 2390-4000 CM-1

    Science.gov (United States)

    Loos, Joep; Birk, Manfred; Wagner, Georg

    2017-06-01

    A new experimental line parameter list of water vapor absorption lines in the spectral ranges 1850 - 2280 cm-1 and 2390 - 4000 cm-1 is presented. The line list is based on the analysis of several transmittance spectra measured using a Bruker IFS 125 HR high resolution Fourier transform spectrometer. A total of 54 measurements of pure water and water/air-mixtures at 296 K as well as water/air-mixtures at high and low temperatures were performed. A multispectrum fitting approach was used applying a quadratic speed-dependent hard collision line shape model in the Hartmann-Tran implementation extended to account for line mixing in the Rosenkranz approximation in order to retrieve line positions, intensities, self- and air-broadening parameters, their speed-dependence, self- and air-shifts as well as line mixing and in some cases collisional narrowing parameters. Additionally, temperature dependence parameters for widths, shifts and in a few cases line mixing were retrieved. For every parameter an extensive error estimation calculation was performed identifying and specifying systematic error sources. The resulting parameters are compared to the databases HITRAN12 as well as experimental values. For intensities, a detailed comparison to results of recent ab initio calculations performed at University College London was done showing an agreement within 2 % for a majority of the data. However, for some bands there are systematic deviations attributed to ab initio calculation errors. .H. Ngo et al. JQSRT 129, 89-100 (2013) doi:10.1016/j.jqsrt.2013.05.034; JQSRT 134, 105 (2014) doi:10.1016/j.jqsrt.2013.10.016. H. Tran et al. JQSRT 129, 199-203 (2013) doi:10.1016/j.jqsrt.2013.06.015; JQSRT 134, 104 (2014) doi:10.1016/j.jqsrt.2013.10.015. L.S. Rothman et al. JQSRT 130, 4-50 (2013) doi:10.1016/j.jqsrt.2013.07.002. N. Jacquinet-Husson et al. JMS 112, 2395-2445 (2016) doi:10.1016/j.jms.2016.06.007.

  14. On M3-transition rates in selected odd-mass nuclei

    Energy Technology Data Exchange (ETDEWEB)

    Lombard, R.J. E-mail: lombard@ipno.in2p3.fr; Vdovin, A.I.; Shirikova, N.Yu.; Sushkov, A.V

    2003-06-02

    The reduced probabilities of M3 transitions are studied in five deformed and three spherical or near-spherical odd-mass nuclei. In deformed nuclei, the states linked by M3 transitions are predominantly of single-quasiparticle nature and the calculations are performed taking into account the single-quasiparticle as well as core-polarization terms in the M3-operator. Whereas in {sup 159}Ho, {sup 175}Yb, and {sup 179}Hf the ratio between theoretical and experimental B(M3) values range from 0.5 to 1.4, the situation is much worse in neutron deficient nuclides {sup 179}W and {sup 183}Pt where the theory used can not explain a very sharp drop of the B(M3) values. In the soft nuclei {sup 121}Cs and {sup 207}Po the states connected by M3 transitions are treated as 'quasiparticle x phonon' states. In {sup 113}Sn, the small 'quasiparticle x phonon' components are not sufficient to compensate vanishing contribution of the dominant quasiparticle component, which shares {delta}l forbidden transitions. Thus, on the whole theoretical description of B(M3) with the present simple models seems to be unsatisfactory. It constitutes a challenging problem both at the level of the nuclear structure and the transition operator.

  15. Energy transfers and spectral eddy viscosity in large-eddy simulations of homogeneous isotropic turbulence: Comparison of dynamic Smagorinsky and multiscale models over a range of discretizations

    NARCIS (Netherlands)

    Hughes, T.J.R.; Wells, G.N.; Wray, A.A.

    2004-01-01

    Energy transfers within large-eddy simulation (LES) and direct numerical simulation (DNS) grids are studied. The spectral eddy viscosity for conventional dynamic Smagorinsky and variational multiscale LES methods are compared with DNS results. Both models underestimate the DNS results for a very coa

  16. M3: Matrix Multiplication on MapReduce

    DEFF Research Database (Denmark)

    Silvestri, Francesco; Ceccarello, Matteo

    2015-01-01

    M3 is an Hadoop library for performing dense and sparse matrix multiplication in MapReduce. The library is based on multi-round algorithms exploiting the 3D decomposition of the problem.......M3 is an Hadoop library for performing dense and sparse matrix multiplication in MapReduce. The library is based on multi-round algorithms exploiting the 3D decomposition of the problem....

  17. An Impurity Emission Survey in the near UV and Visible Spectral Ranges of Electron Cyclotron Heated (ECH) Plasma in the TJ-II Stellarator

    Energy Technology Data Exchange (ETDEWEB)

    McCarthy, K. J.; Zurro, B.; Baciero, A.

    2001-07-01

    We report on a near-ultraviolet and visible spectroscopic survey (220-600 nm) of electron cyclotron resonance (ECR) heated plasmas created in the TJ-II stellarator, with central electron temperatures up to 2 keV and central electron densities up to 1.7 x 10 ''19 m''-3. Approximately 1200 lines from thirteen elements have been identified. The purpose of the work is to identify the principal impurities and spectral lines present in TJ-II plasmas, as well as their possible origin to search for transitions from highly ionised ions. This work will act as a base for identifying suitable transitions for following the evolution of impurities under different operating regimens and multiplet systems for line polarisation studies. It is intended to use the database creates as a spectral line reference for comparing spectra under different operating and plasma heating regimes. (Author)

  18. Computer Control of the Spectral Composition of the Powerful Laser System Irradiation with a Wide Range of Laser Transitions on Metal Vapors

    Directory of Open Access Journals (Sweden)

    Soldatov Anatoly

    2016-01-01

    Full Text Available The results of the experimental study cycle of the multiwave metal vapor laser system on the basis of the original configuration of the multimedia laser emitter. The spectral parameters of the setup have been controlled using a personal computer (PC. This allows carrying out their independent optimization according to excitation conditions, and, therefore, promptly allocating the output set of oscillating wavelengths and their relative distribution in power, which makes the system attractive for scientific and technological application.

  19. M3D project for simulation studies of plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Park, W.; Belova, E.V.; Fu, G.Y. [Princeton Univ., NJ (United States). Plasma Physics Lab.; Strauss, H.R. [New York Univ., NY (United States); Sugiyama, L.E. [Massachusetts Inst. of Tech., Cambridge, MA (United States)

    1998-12-31

    The M3D (Multi-level 3D) project carries out simulation studies of plasmas of various regimes using multi-levels of physics, geometry, and mesh schemes in one code package. This paper and papers by Strauss, Sugiyama, and Belova in this workshop describe the project, and present examples of current applications. The currently available physics models of the M3D project are MHD, two-fluids, gyrokinetic hot particle/MHD hybrid, and gyrokinetic particle ion/two-fluid hybrid models. The code can be run with both structured and unstructured meshes.

  20. Assembly language programming ARM Cortex-M3

    CERN Document Server

    Mahout, Vincent

    2013-01-01

    ARM designs the cores of microcontrollers which equip most "embedded systems" based on 32-bit processors. Cortex M3 is one of these designs, recently developed by ARM with microcontroller applications in mind. To conceive a particularly optimized piece of software (as is often the case in the world of embedded systems) it is often necessary to know how to program in an assembly language.This book explains the basics of programming in an assembly language, while being based on the architecture of Cortex M3 in detail and developing many examples.It is written for people who have never pr

  1. Optimizing Concurrent M3-Transactions: A Fuzzy Constraint Satisfaction Approach

    Directory of Open Access Journals (Sweden)

    Peng LI

    2004-10-01

    Full Text Available Due to the high connectivity and great convenience, many E-commerce application systems have a high transaction volume. Consequently, the system state changes rapidly and it is likely that customers issue transactions based on out-of-date state information. Thus, the potential of transaction abortion increases greatly. To address this problem, we proposed an M3-transaction model. An M3-transaction is a generalized transaction where users can issue their preferences in a request by specifying multiple criteria and optional data resources simultaneously within one transaction. In this paper, we introduce the transaction grouping and group evaluation techniques. We consider evaluating a group of M3-transactions arrived to the system within a short duration together. The system makes optimal decisions in allocating data to transactions to achieve better customer satisfaction and lower transaction failure rate. We apply the fuzzy constraint satisfaction approach for decision-making. We also conduct experimental studies to evaluate the performance of our approach. The results show that the M3-transaction with group evaluation is more resilient to failure and yields much better performance than the traditional transaction model.

  2. Optimizing Concurrent M3-Transactions: A Fuzzy Constraint Satisfaction Approach

    Directory of Open Access Journals (Sweden)

    Peng LI

    2004-10-01

    Full Text Available Due to the high connectivity and great convenience, many E-commerce application systems have a high transaction volume. Consequently, the system state changes rapidly and it is likely that customers issue transactions based on out-of-date state information. Thus, the potential of transaction abortion increases greatly. To address this problem, we proposed an M3-transaction model. An M3-transaction is a generalized transaction where users can issue their preferences in a request by specifying multiple criteria and optional data resources simultaneously within one transaction. In this paper, we introduce the transaction grouping and group evaluation techniques. We consider evaluating a group of M3-transactions arrived to the system within a short duration together. The system makes optimal decisions in allocating data to transactions to achieve better customer satisfaction and lower transaction failure rate. We apply the fuzzy constraint satisfaction approach for decision-making. We also conduct experimental studies to evaluate the performance of our approach. The results show that the M3-transaction with group evaluation is more resilient to failure and yields much better performance than the traditional transaction model.

  3. M3: An Open Model for Measuring Code Artifacts

    NARCIS (Netherlands)

    Izmaylova, A.; Klint, P.; Shahi, A.; Vinju, J.J.

    2013-01-01

    In the context of the EU FP7 project ``OSSMETER'' we are developing an infra-structure for measuring source code. The goal of OSSMETER is to obtain insight in the quality of open-source projects from all possible perspectives, including product, process and community. This is a "white paper" on M3,

  4. Low-lying electronic states of M(3)O(9)(-) and M(3)O(9)(2-) (M = Mo, W).

    Science.gov (United States)

    Li, Shenggang; Dixon, David A

    2007-11-01

    Multiple low-lying electronic states of M(3)O(9)(-) and M(3)O(9)(2-) (M = Mo, W) arise from the occupation of the near-degenerate low-lying virtual orbitals in the neutral clusters. We used density functional theory (DFT) and coupled cluster theory (CCSD(T)) with correlation consistent basis sets to study the structures and energetics of the electronic states of these anions. The adiabatic and vertical electron detachment energies (ADEs and VDEs) of the anionic clusters were calculated with 27 exchange-correlation functionals including one local spin density approximation functional, 13 generalized gradient approximation (GGA) functionals, and 13 hybrid GGA functionals, as well as the CCSD(T) method. For M(3)O(9)(-), CCSD(T) and nearly all of the DFT exchange-correlation functionals studied predict the (2)A(1) state arising from the Jahn-Teller distortion due to singly occupying the degenerate e' orbital to be lower in energy than the (2)A(1)' state arising from singly occupying the nondegenerate a(1)' orbital. For W(3)O(9)(-), the (2)A(1) state was predicted to have essentially the same energy as the (2)A(1)' state at the CCSD(T) level with core-valence correlation corrections included and to be higher in energy or essentially isoenergetic with most DFT methods. The calculated VDEs from the CCSD(T) method are in reasonable agreement with the experimental values for both electronic states if estimates for the corrections due to basis set incompleteness are included. For M(3)O(9)(2-), the singlet state arising from doubly occupying the nondegenerate a(1)' orbital was predicted to be the most stable state for both M = Mo and W. However, whereas M(3)O(9)(2-) was predicted to be less stable than M(3)O(9)(-), W(3)O(9)(2-) was predicted to be more stable than W(3)O(9)(-).

  5. Context Dependent Spectral Unmixing

    Science.gov (United States)

    2014-08-01

    International Geoscience and Remote Sensing Symposium (IGARSS), Cape Town, South Africa , July 2009. HONORS AND AWARDS: 1. IEEE Outstanding CECS Student Award...COMMEND on the Usgs1C2M3 data across the 25 runs and at all noise levels: (a) SME , (b) SMAE, (c) AME. . . . . . . . . . . . . . 59 6.10 True (solid lines...identifying multiple sets of endmembers. In other words, the unmixing process is adapted to different regions of the spectral space. Another challenge with most

  6. M3与M5的MICM鉴别

    Institute of Scientific and Technical Information of China (English)

    索翠平; 李寅; 赵霞

    2003-01-01

    @@ 急性早幼粒细胞自血病(M3型,acute promyelocytic leukemia,APL)和急性单核细胞白血病(M5型,acute monocytic leukemia,AMOL)同属于急性非淋巴细胞白血病.二者在临床与形态上均有相似之处,特别是细颗粒型急性早幼粒细胞白血病(M3b)在形态上更易被误诊为急性单核细胞白血病.但二者的治疗与预后却有很大的区别.在此,结合MICM分型原则对二者加以鉴别,以免造成误诊,导致不应有的后果.

  7. An imaging Fourier transform spectroradiometer with a multi-element photodetector for the spectral range of 7-14 μm

    Science.gov (United States)

    Bashkin, S. V.; Karfidov, A. O.; Kornienko, V. N.; Lel'kov, M. V.; Mironov, A. I.; Morozov, A. N.; Svetlichnyi, S. I.; Tabalin, S. E.; Fufurin, I. L.

    2016-09-01

    The construction and principle of operation of a imaging Fourier transform infrared spectroradiometer (FTIR spectrometer) equipped with a cooled 32-area photodetector designed for spectral analysis of open atmospheric paths are considered. The main technical characteristics of the Fourier spectrometer are reported. The technique of visualization of the detected vapor cloud is described. The results of field experiments using the imaging FTIR spectrometer are shown. Based on these results, the dynamics of motion of the cloud of material has been investigated, its angular and linear velocities have been estimated, and data on propagation of the cloud of material and change in its angular sizes in air have been obtained. A technique for analyzing data provided by two FTIR spectrometers is given, based on which one can estimate the size of the cloud and the distance to it from each device. It is shown that the results of detection of the cloud of material by the imaging FTIR spectrometer can be used to predict the propagation of material under study in space.

  8. First INTEGRAL observations of V404 Cygni during the 2015 outburst : spectral behavior in the 20 - 650 keV energy range

    CERN Document Server

    Roques, Jean-Pierre; Bazzano, Angela; Fiocchi, Mariateresa; Natalucci, Lorenzo; Ubertini, Pietro

    2015-01-01

    In June 2015, the source V404 Cygni (= GS2023+38) underwent an extraordinary outburst. We present the results obtained during the first revolution dedicated to this target by the INTEGRAL mission, and focus on the spectral behavior in the hard X-ray domain, using both SPI and IBIS instruments. The source exhibits extreme variability, and reaches fluxes of several tens of Crab. However, the emission between 20 and 650 keV can be understood in terms of two main components, varying on all the observable timescales, similar to what is observed in the persistent black hole system Cyg X-1. The low energy component (up to ~ 200 keV) presents a rather unusual shape, probably due to the intrinsic source variability. Nonetheless, a satisfactory description is obtained with a Comptonization model, if an unusually hot population of seed photons ($kT_0$ ~ 7 keV) is introduced. Above this first component, a clear excess extending up to 400-600 keV leads us to investigate a scenario where an additional (cutoff) power law co...

  9. FIRST INTEGRAL OBSERVATIONS OF V404 CYGNI DURING THE 2015 OUTBURST: SPECTRAL BEHAVIOR IN THE 20–650 KeV ENERGY RANGE

    Energy Technology Data Exchange (ETDEWEB)

    Roques, Jean-Pierre; Jourdain, Elisabeth [Université Toulouse, UPS-OMP, CNRS, IRAP, 9 Av. Roche, BP 44346, F-31028 Toulouse (France); Bazzano, Angela; Fiocchi, Mariateresa; Natalucci, Lorenzo; Ubertini, Pietro [Istituto di Astrofisica e Planetologia Spaziali, INAF, Via Fosso del Cavaliere 100, I-00133 Roma, Italy (Italy)

    2015-11-01

    In 2015 June, the source V404 Cygni (= GS2023+38) underwent an extraordinary outburst. We present the results obtained during the first revolution dedicated to this target by the INTEGRAL mission and focus on the spectral behavior in the hard X-ray domain, using both SPI and IBIS instruments. The source exhibits extreme variability and reaches fluxes of several tens of Crab. However, the emission between 20 and 650 keV can be understood in terms of two main components, varying on all the observable timescales, similar to what is observed in the persistent black hole system Cyg X-1. The low-energy component (up to ∼200 keV) presents a rather unusual shape, probably due to the intrinsic source variability. Nonetheless, a satisfactory description is obtained with a Comptonization model, if an unusually hot population of seed photons (kT{sub 0} ∼ 7 keV) is introduced. Above this first component, a clear excess extending up to 400–600 keV leads us to investigate a scenario where an additional (cutoff) power law could correspond to the contribution of the jet synchrotron emission, as proposed in Cyg X-1. A search for an annihilation feature did not provide any firm detection, with an upper limit of 2 × 10{sup −4} ph cm{sup −2} s{sup −1} (2σ) for a narrow line centered at 511 keV, on the averaged obtained spectrum.

  10. First INTEGRAL Observations of V404 Cygni during the 2015 Outburst: Spectral Behavior in the 20-650 keV Energy Range

    Science.gov (United States)

    Roques, Jean-Pierre; Jourdain, Elisabeth; Bazzano, Angela; Fiocchi, Mariateresa; Natalucci, Lorenzo; Ubertini, Pietro

    2015-11-01

    In 2015 June, the source V404 Cygni (= GS2023+38) underwent an extraordinary outburst. We present the results obtained during the first revolution dedicated to this target by the INTEGRAL mission and focus on the spectral behavior in the hard X-ray domain, using both SPI and IBIS instruments. The source exhibits extreme variability and reaches fluxes of several tens of Crab. However, the emission between 20 and 650 keV can be understood in terms of two main components, varying on all the observable timescales, similar to what is observed in the persistent black hole system Cyg X-1. The low-energy component (up to ˜200 keV) presents a rather unusual shape, probably due to the intrinsic source variability. Nonetheless, a satisfactory description is obtained with a Comptonization model, if an unusually hot population of seed photons (kT0 ˜ 7 keV) is introduced. Above this first component, a clear excess extending up to 400-600 keV leads us to investigate a scenario where an additional (cutoff) power law could correspond to the contribution of the jet synchrotron emission, as proposed in Cyg X-1. A search for an annihilation feature did not provide any firm detection, with an upper limit of 2 × 10-4 ph cm-2 s-1 (2σ) for a narrow line centered at 511 keV, on the averaged obtained spectrum. Based on observations with INTEGRAL, an ESA project with instruments and science data center funded by ESA member states (especially the PI countries: Denmark, France, Germany, Italy, Spain, and Switzerland), Czech Republic, and Poland with the participation of Russia and USA.

  11. Absolute distance measurement method without a non-measurable range and directional ambiguity based on the spectral-domain interferometer using the optical comb of the femtosecond pulse laser

    Science.gov (United States)

    Park, J.; Jin, J.; Kim, J.-A.; Kim, J. W.

    2016-12-01

    With the help of the optical comb of a femtosecond pulse laser, a spectral-domain interferometer has been utilized for measuring absolute distances. Even if the technique can measure distances at a high speed and with good precision, it has two fundamental problems: non-measurable range and directional ambiguity. First, the non-measurable range arises due to the sampling limit of the interference spectra at very short distances or the integer multiple of a double non-ambiguity range. Second, the peak corresponding to the desired distance in the Fourier domain has a directional ambiguity owing to the repeated property of the optical comb. Therefore, due to these two fundamental problems, most previous works never measure the absolute distances by itself in a single operation. In this letter, an interferometric method for measuring arbitrary absolute distances based on a spectral-domain interferometer operating with two reference mirrors is proposed and demonstrated. The two reference mirrors generate two distinguishable signals, primary and secondary, with a predetermined offset, thus solving these fundamental problems clearly. More importantly, as a practical advantage, the simple layout of the proposed method makes it readily applicable to most previous studies.

  12. Structure and dynamics of the M3 muscarinic acetylcholine receptor

    Energy Technology Data Exchange (ETDEWEB)

    Kruse, Andrew C.; Hu, Jianxin; Pan, Albert C.; Arlow, Daniel H.; Rosenbaum, Daniel M.; Rosemond, Erica; Green, Hillary F.; Liu, Tong; Chae, Pil Seok; Dror, Ron O.; Shaw, David E.; Weis, William I.; Wess, Jürgen; Kobilka, Brian K. (Stanford); (NIH); (D.E. Shaw); (Hanyang); (UTSMC)

    2012-03-01

    Acetylcholine, the first neurotransmitter to be identified, exerts many of its physiological actions via activation of a family of G-protein-coupled receptors (GPCRs) known as muscarinic acetylcholine receptors (mAChRs). Although the five mAChR subtypes (M1-M5) share a high degree of sequence homology, they show pronounced differences in G-protein coupling preference and the physiological responses they mediate. Unfortunately, despite decades of effort, no therapeutic agents endowed with clear mAChR subtype selectivity have been developed to exploit these differences. We describe here the structure of the G{sub q/11}-coupled M3 mAChR ('M3 receptor', from rat) bound to the bronchodilator drug tiotropium and identify the binding mode for this clinically important drug. This structure, together with that of the G{sub i/o}-coupled M2 receptor, offers possibilities for the design of mAChR subtype-selective ligands. Importantly, the M3 receptor structure allows a structural comparison between two members of a mammalian GPCR subfamily displaying different G-protein coupling selectivities. Furthermore, molecular dynamics simulations suggest that tiotropium binds transiently to an allosteric site en route to the binding pocket of both receptors. These simulations offer a structural view of an allosteric binding mode for an orthosteric GPCR ligand and provide additional opportunities for the design of ligands with different affinities or binding kinetics for different mAChR subtypes. Our findings not only offer insights into the structure and function of one of the most important GPCR families, but may also facilitate the design of improved therapeutics targeting these critical receptors.

  13. The boundary RSOS \\mathcal{M}(3,5) model

    CERN Document Server

    Deeb, Omar El

    2015-01-01

    We consider the critical non-unitary minimal model {\\cal M}(3,5) with integrable boundaries. We analyze the patterns of zeros of the eigenvalues of the transfer matrix and then determine the spectrum of the critical theory through the Thermodynamic Bethe Ansatz (TBA) equations. We derive these equations for all excitations by solving, the TBA functional equation satisfied by the transfer matrices of the associated A_{4} RSOS lattice model of Forrester and Baxter in Regime III, then determine their corresponding energies. The excitations are classified in terms of (m,n) systems.

  14. 3000m3/h cutter-suction dredge

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    @@ In October 2004, the Fumin 9 3000 m3/h cutter-suction dredge co-designed by the Dutch IHC and Guangzhou Wenchong Shipyard went through a dock usability test and a 25 meter clean water test. The dredge is the largest of its kind in China, and the most advanced and most efficient cutter-suction dredge in the world. The IHC was responsible for the design of the ship till its working design was taken over by Guangzhou Wenchong Shipyard, the builder of the dredge, who had started its construction on October 23, 2003.

  15. Hydraulic supports for polishing TMT M3MP

    Science.gov (United States)

    Hu, Haifei; Qi, Erhui; Cole, Glen; Hu, Haixiang; Luo, Xiao; Ford, Virginia; Zhang, Xuejun

    2016-10-01

    For polishing the ultra-thin TMT M3MP, a polishing support system with 18 hydraulic supports (HS) is introduced. This work focuses on the designing and testing of these HSs. Firstly the design concept of HS system is discussed; then mechanical implementation of the HS structure is carried out, with special consideration of fluid cycling, work pressurization and the weight component. Afterward the piping installation and the de-gas process for the working fluid are implemented. Pressurization and stiffness are well checked before system integration for the single HS unit. Finally the support system is integrated for the polishing process.

  16. Heteronuclear Micro-Helmholtz Coil Facilitates µm-Range Spatial and Sub-Hz Spectral Resolution NMR of nL-Volume Samples on Customisable Microfluidic Chips.

    Science.gov (United States)

    Spengler, Nils; Höfflin, Jens; Moazenzadeh, Ali; Mager, Dario; MacKinnon, Neil; Badilita, Vlad; Wallrabe, Ulrike; Korvink, Jan G

    2016-01-01

    We present a completely revised generation of a modular micro-NMR detector, featuring an active sample volume of ∼ 100 nL, and an improvement of 87% in probe efficiency. The detector is capable of rapidly screening different samples using exchangeable, application-specific, MEMS-fabricated, microfluidic sample containers. In contrast to our previous design, the sample holder chips can be simply sealed with adhesive tape, with excellent adhesion due to the smooth surfaces surrounding the fluidic ports, and so withstand pressures of ∼2.5 bar, while simultaneously enabling high spectral resolution up to 0.62 Hz for H2O, due to its optimised geometry. We have additionally reworked the coil design and fabrication processes, replacing liquid photoresists by dry film stock, whose final thickness does not depend on accurate volume dispensing or precise levelling during curing. We further introduced mechanical alignment structures to avoid time-intensive optical alignment of the chip stacks during assembly, while we exchanged the laser-cut, PMMA spacers by diced glass spacers, which are not susceptible to melting during cutting. Doing so led to an overall simplification of the entire fabrication chain, while simultaneously increasing the yield, due to an improved uniformity of thickness of the individual layers, and in addition, due to more accurate vertical positioning of the wirebonded coils, now delimited by a post base plateau. We demonstrate the capability of the design by acquiring a 1H spectrum of ∼ 11 nmol sucrose dissolved in D2O, where we achieved a linewidth of 1.25 Hz for the TSP reference peak. Chemical shift imaging experiments were further recorded from voxel volumes of only ∼ 1.5 nL, which corresponded to amounts of just 1.5 nmol per voxel for a 1 M concentration. To extend the micro-detector to other nuclei of interest, we have implemented a trap circuit, enabling heteronuclear spectroscopy, demonstrated by two 1H/13C 2D HSQC experiments.

  17. Heteronuclear Micro-Helmholtz Coil Facilitates µm-Range Spatial and Sub-Hz Spectral Resolution NMR of nL-Volume Samples on Customisable Microfluidic Chips.

    Directory of Open Access Journals (Sweden)

    Nils Spengler

    Full Text Available We present a completely revised generation of a modular micro-NMR detector, featuring an active sample volume of ∼ 100 nL, and an improvement of 87% in probe efficiency. The detector is capable of rapidly screening different samples using exchangeable, application-specific, MEMS-fabricated, microfluidic sample containers. In contrast to our previous design, the sample holder chips can be simply sealed with adhesive tape, with excellent adhesion due to the smooth surfaces surrounding the fluidic ports, and so withstand pressures of ∼2.5 bar, while simultaneously enabling high spectral resolution up to 0.62 Hz for H2O, due to its optimised geometry. We have additionally reworked the coil design and fabrication processes, replacing liquid photoresists by dry film stock, whose final thickness does not depend on accurate volume dispensing or precise levelling during curing. We further introduced mechanical alignment structures to avoid time-intensive optical alignment of the chip stacks during assembly, while we exchanged the laser-cut, PMMA spacers by diced glass spacers, which are not susceptible to melting during cutting. Doing so led to an overall simplification of the entire fabrication chain, while simultaneously increasing the yield, due to an improved uniformity of thickness of the individual layers, and in addition, due to more accurate vertical positioning of the wirebonded coils, now delimited by a post base plateau. We demonstrate the capability of the design by acquiring a 1H spectrum of ∼ 11 nmol sucrose dissolved in D2O, where we achieved a linewidth of 1.25 Hz for the TSP reference peak. Chemical shift imaging experiments were further recorded from voxel volumes of only ∼ 1.5 nL, which corresponded to amounts of just 1.5 nmol per voxel for a 1 M concentration. To extend the micro-detector to other nuclei of interest, we have implemented a trap circuit, enabling heteronuclear spectroscopy, demonstrated by two 1H/13C 2D HSQC

  18. InSe and GaSe considered as efficient photosensitive materials in a wide spectral range (1-6 eV)

    Energy Technology Data Exchange (ETDEWEB)

    Salaev, E.IU.; Godzhaev, M.O.; Aliev, E.T.; Zarbaliev, M.Z.

    1988-09-01

    Experimental results are presented on the quantum efficiency of the photoconductance of layered crystals of InSe and GaSe (candidate UV-detector materials), indicating that these crystals have high values of photosensitivity up to photon energies of 6 eV. The elevated quantum efficiency of these crystals in the UV range is connected with changes in the scattering mechanism of charge carriers and their lifetime near the surface of the material. 8 references.

  19. Thermal coagulation-induced changes of the optical properties of normal and adenomatous human colon tissues in vitro in the spectral range 400-1100 nm

    Energy Technology Data Exchange (ETDEWEB)

    Ao Huilan; Xing Da; Wei Huajiang; Gu Huaimin [MOE Key Laboratory of Laser Life Science and Institute of Laser Life Science, ina Normal University, Guangzhou 510631 (China); Wu Guoyong; Lu Jianjun [Department of Surgery, The First Affiliated Hospital, Sun Yat-Sen University, Guangzhou 510080 (China)], E-mail: xingda@scnu.edu.cn

    2008-04-21

    The absorption coefficients, the reduced scattering coefficients and the optical penetration depths for native and coagulated human normal and adenomatous colon tissues in vitro were determined over the range of 400-1100 nm using a spectrophotometer with an internal integrating sphere system, and the inverse adding-doubling method was applied to calculate the tissue optical properties from diffuse reflectance and total transmittance measurements. The experimental results showed that in the range of 400-1100 nm there were larger absorption coefficients (P < 0.01) and smaller reduced scattering coefficients (P < 0.01) for adenomatous colon tissues than for normal colon tissues, and there were smaller optical penetration depths for adenomatous colon tissues than for normal colon tissues, especially in the near-infrared wavelength. Thermal coagulation induced significant increase of the absorption coefficients and reduced scattering coefficients for the normal and adenomatous colon tissues, and significantly reduced decrease of the optical penetration depths for the normal and adenomatous colon tissues. The smaller optical penetration depth for coagulated adenomatous colon tissues is a disadvantage for laser-induced thermotherapy (LITT) and photodynamic therapy (PDT). It is necessary to adjust the application parameters of lasers to achieve optimal therapy.

  20. 人体目标光谱特性对微光像增强器视距的影响%Influence of Human Body Target ’ s Spectral Characteristics on Visual Range of Low Light Level Image Intensifiers

    Institute of Scientific and Technical Information of China (English)

    张俊举; 杨文彬; 许辉; 刘磊; 陶媛媛

    2013-01-01

    To study the effect of different human target’s spectral reflective characteristic on low light level (LLL) image intensi-fier’s distance ,based on the spectral characteristics of the night-sky radiation and the spectral reflective coefficients of common clothes ,we established a equation of human body target’s spectral reflective distribution ,and analyzed the spectral reflective characteristics of different human targets wearing the clothes of different color and different material ,and from the actual detec-tion equation of LLL image intensifier distance ,discussed the detection capability of LLL image intensifier for different human target .The study shows that the effect of different human target’s spectral reflective characteristic on LLL image intensifier dis-tance is mainly reflected in the average reflectivity ρand the initial contrast of the target and the background C0 .Reflective coeffi-cient and spectral reflection intensity of cotton clothes are higher than polyester clothes ,and detection capability of LLL image intensifier is stronger for the human target wearing cotton clothes .Experimental results show that the LLL image intensifiers have longer visual ranges for targets who wear cotton clothes than targets who wear same color but polyester clothes ,and have longer visual ranges for targets who wear light-colored clothes than targets who wear dark-colored clothes .And in the full moon illumination conditions ,LLL image intensifiers are more sensitive to the clothes’ material .%为研究不同人体目标的反射光谱特性对微光像增强器视距的影响,以夜天空辐射光谱特性和常见衣服的光谱反射系数为基础,建立了人体目标的反射光谱分布方程,分析了人体目标穿着不同材质和颜色衣服时的反射光谱特性,并从微光像增强器视距实际探测方程出发,讨论了微光像增强器对不同人体目标的探测能力。发现不同人体目标的反射光谱特性

  1. On the spectral domain approach to long-range propagation of high-frequency waves along a strip conductor above a PEC surface

    CERN Document Server

    Norgren, Martin

    2012-01-01

    A generic problem of high frequency wave propagation along a metallic strip in parallel above a PEC ground plane is considered. The wave is excited by an elemental electric dipole at an arbitrary location above the PEC plane. The full wave problem, for arbitrary widths of the strip, is solved by means of a mode matching approach and expansion of the strip surface current into Chebyshev polynomials. For narrow strips, an approximate method using only longitudinal currents is derived, and compared numerically with the full wave method. Utilizing the concept of equivalent radius, the approximate method for narrow strips is evaluated numerically against results for thin circular wires. It is concluded that the approximate method is suitable for handling multiple wires in layered structures, wherefore the method has potential usefulness for estimating long range propagation of high frequency waves in wire structures like power lines and railway feeding systems, containing over-head wires and wires submerged into g...

  2. Determination of Seed Soundness in Conifers Cryptomeria japonica and Chamaecyparis obtusa Using Narrow-Multiband Spectral Imaging in the Short-Wavelength Infrared Range.

    Science.gov (United States)

    Matsuda, Osamu; Hara, Masashi; Tobita, Hiroyuki; Yazaki, Kenichi; Nakagawa, Toshinori; Shimizu, Kuniyoshi; Uemura, Akira; Utsugi, Hajime

    2015-01-01

    Regeneration of planted forests of Cryptomeria japonica (sugi) and Chamaecyparis obtuse (hinoki) is the pressing importance to the forest administration in Japan. Low seed germination rate of these species, however, has hampered low-cost production of their seedlings for reforestation. The primary cause of the low germinability has been attributed to highly frequent formation of anatomically unsound seeds, which are indistinguishable from sound germinable seeds by visible observation and other common criteria such as size and weight. To establish a method for sound seed selection in these species, hyperspectral imaging technique was used to identify a wavelength range where reflectance spectra differ clearly between sound and unsound seeds. In sound seeds of both species, reflectance in a narrow waveband centered at 1,730 nm, corresponding to a lipid absorption band in the short-wavelength infrared (SWIR) range, was greatly depressed relative to that in adjacent wavebands on either side. Such depression was absent or less prominent in unsound seeds. Based on these observations, a reflectance index SQI, abbreviated for seed quality index, was formulated using reflectance at three narrow SWIR wavebands so that it represents the extent of the depression. SQI calculated from seed area-averaged reflectance spectra and spatial distribution patterns of pixelwise SQI within each seed area were both proven as reliable criteria for sound seed selection. Enrichment of sound seeds was accompanied by an increase in germination rate of the seed lot. Thus, the methods described are readily applicable toward low-cost seedling production in combination with single seed sowing technology.

  3. Determination of Seed Soundness in Conifers Cryptomeria japonica and Chamaecyparis obtusa Using Narrow-Multiband Spectral Imaging in the Short-Wavelength Infrared Range.

    Directory of Open Access Journals (Sweden)

    Osamu Matsuda

    Full Text Available Regeneration of planted forests of Cryptomeria japonica (sugi and Chamaecyparis obtuse (hinoki is the pressing importance to the forest administration in Japan. Low seed germination rate of these species, however, has hampered low-cost production of their seedlings for reforestation. The primary cause of the low germinability has been attributed to highly frequent formation of anatomically unsound seeds, which are indistinguishable from sound germinable seeds by visible observation and other common criteria such as size and weight. To establish a method for sound seed selection in these species, hyperspectral imaging technique was used to identify a wavelength range where reflectance spectra differ clearly between sound and unsound seeds. In sound seeds of both species, reflectance in a narrow waveband centered at 1,730 nm, corresponding to a lipid absorption band in the short-wavelength infrared (SWIR range, was greatly depressed relative to that in adjacent wavebands on either side. Such depression was absent or less prominent in unsound seeds. Based on these observations, a reflectance index SQI, abbreviated for seed quality index, was formulated using reflectance at three narrow SWIR wavebands so that it represents the extent of the depression. SQI calculated from seed area-averaged reflectance spectra and spatial distribution patterns of pixelwise SQI within each seed area were both proven as reliable criteria for sound seed selection. Enrichment of sound seeds was accompanied by an increase in germination rate of the seed lot. Thus, the methods described are readily applicable toward low-cost seedling production in combination with single seed sowing technology.

  4. Determination of Seed Soundness in Conifers Cryptomeria japonica and Chamaecyparis obtusa Using Narrow-Multiband Spectral Imaging in the Short-Wavelength Infrared Range

    Science.gov (United States)

    Matsuda, Osamu; Hara, Masashi; Tobita, Hiroyuki; Yazaki, Kenichi; Nakagawa, Toshinori; Shimizu, Kuniyoshi; Uemura, Akira; Utsugi, Hajime

    2015-01-01

    Regeneration of planted forests of Cryptomeria japonica (sugi) and Chamaecyparis obtuse (hinoki) is the pressing importance to the forest administration in Japan. Low seed germination rate of these species, however, has hampered low-cost production of their seedlings for reforestation. The primary cause of the low germinability has been attributed to highly frequent formation of anatomically unsound seeds, which are indistinguishable from sound germinable seeds by visible observation and other common criteria such as size and weight. To establish a method for sound seed selection in these species, hyperspectral imaging technique was used to identify a wavelength range where reflectance spectra differ clearly between sound and unsound seeds. In sound seeds of both species, reflectance in a narrow waveband centered at 1,730 nm, corresponding to a lipid absorption band in the short-wavelength infrared (SWIR) range, was greatly depressed relative to that in adjacent wavebands on either side. Such depression was absent or less prominent in unsound seeds. Based on these observations, a reflectance index SQI, abbreviated for seed quality index, was formulated using reflectance at three narrow SWIR wavebands so that it represents the extent of the depression. SQI calculated from seed area-averaged reflectance spectra and spatial distribution patterns of pixelwise SQI within each seed area were both proven as reliable criteria for sound seed selection. Enrichment of sound seeds was accompanied by an increase in germination rate of the seed lot. Thus, the methods described are readily applicable toward low-cost seedling production in combination with single seed sowing technology. PMID:26083366

  5. 针对MCU应用的Cortex-M3

    Institute of Scientific and Technical Information of China (English)

    费浙平

    2005-01-01

    传统上MCU领域一直由4/8位架构占据了主导地位,部分采用16位架构,而32位才刚起步,在多数人印象中它还是一种奢侈的高端应用。但近几年这种情况已有了很大变化,越来越多的设计采用32位MCU架构,而ARMCotex—M3的面世也为32位MCU应用带来更多可能。

  6. Wavelength conversion based spectral imaging

    DEFF Research Database (Denmark)

    Dam, Jeppe Seidelin

    There has been a strong, application driven development of Si-based cameras and spectrometers for imaging and spectral analysis of light in the visible and near infrared spectral range. This has resulted in very efficient devices, with high quantum efficiency, good signal to noise ratio and high...... resolution for this spectral region. Today, an increasing number of applications exists outside the spectral region covered by Si-based devices, e.g. within cleantech, medical or food imaging. We present a technology based on wavelength conversion which will extend the spectral coverage of state of the art...... visible or near infrared cameras and spectrometers to include other spectral regions of interest....

  7. Joint M3 and Diviner Analysis of the Mineralogy, Glass Composition, and Country Rock Content of Pyroclastic Deposits in Oppenheimer Crater

    Science.gov (United States)

    Bennett, Kristen A.; Horgan, Briony H. N.; Greenhagen, Benjamin T.; Allen, Carlton C.; Paige, David A.; Bell, James F., III

    2013-01-01

    Here we present our analysis of the near- and mid-infrared spectral properties of pyroclastic deposits within the floor fractured Oppenheimer Crater that are hypothesized to be Vulcanian in origin. These are the first results of our global study of lunar pyroclastic deposits aimed at constraining the range of eruption processes on the Moon. In the near-infrared, we have employed a new method of spectral analysis developed in Horgan et al. (2013) of the 1 ?m iron absorption band in Chandrayaan-1 Moon Mineralogy Mapper (M3) spectra. By analyzing both the position and shape of the 1 ?m band we can detect and map the distribution of minerals, glasses, and mixtures of these phases in pyroclastic deposits. We are also using mid-infrared spectra from the Lunar Reconnaissance Orbiter Diviner Lunar Radiometer Experiment to develop 200 m/pixel Christiansen Feature (CF) maps, which correlate with silica abundance. One of the benefits of using CF maps for analysis of pyroclastic deposits is that they can be used to detect silicic country rock that may have been emplaced by Vulcanian-style eruptions, and are sensitive to iron abundance in glasses, neither of which is possible in the near-infrared. M3 analysis reveals that the primary spectral endmembers are low-calcium pyroxene and iron-bearing glass, with only minor high-calcium pyroxene, and no detectable olivine. The large deposit in the south shows higher and more extensive glass concentrations than the surrounding deposits. We interpret the M3 spectra of the pyroclastic deposits as indicating a mixture of low-calcium pyroxene country rock and juvenile glass, and no significant olivine. Analysis of Diviner CF maps of the Oppenheimer crater floor indicates an average CF value of 8.16, consistent with a mixture of primarily plagioclase and some pyroxene. The average CF values of the pyroclastic deposits range from 8.31 in the SW to 8.24 in the SE. Since CF values within the deposits are as high as 8.49, the lower average CF

  8. Assessment of spruce (Picea obovata) abundance by spectral unmixing algorithm for sustainable forest management in highland Natural Reserve (case study of Zigalga Range, South-Ural State Natural Reserve, Russia).

    Science.gov (United States)

    Mikheeva, Anna; Moiseev, Pavel

    2017-04-01

    In mountain territories climate change affects forest productivity and growth, which results in the tree line advancing and increasing of the forest density. These changes pose new challenges for forest managers whose responsibilities include forest resources inventory, monitoring and protection of ecosystems, and assessment of forest vulnerability. These activities require a range of sources of information, including exact squares of forested areas, forest densities and species abundances. Picea obovata, dominant tree species in South-Ural State Natural Reserve, Russia has regenerated, propagated and increased its relative cover during the recent 70 years. A remarkable shift of the upper limit of Picea obovata up to 60-80 m upslope was registered by repeating photography, especially on gentle slopes. The stands of Picea obovata are monitored by Reserve inspectors on the test plots to ensure that forests maintain or improve their productivity, these studies also include projective cover measurements. However, it is impossible to cover the entire territory of the Reserve by detailed field observations. Remote sensing data from Terra ASTER imagery provides valuable information for large territories (scene covers an area of 60 x 60 km) and can be used for quantitative mapping of forest and non-forest vegetation at regional scale (spatial resolution is 15-30 m for visible and infrared bands). A case study of estimating Picea obovata abundance was conducted for forest and forest-tundra sites of Zigalga Range, using 9-band ASTER multispectral imagery of 23.08.2007, field data and spectral unmixing algorithm. This type of algorithms intends to derive object and its abundance from a mixed pixel of multispectral imagery which can be further converted to object's projective cover. Atmospheric correction was applied to the imagery prior to spectral unmixing, and then pure spectra of Picea obovata were extracted from the image in 10 points and averaged. These points located in

  9. Third-harmonic generation in silicon and photonic crystals of macroporous silicon in the spectral intermediate-IR range; Erzeugung der Dritten Harmonischen in Silizium und Photonischen Kristallen aus makroporoesem Silizium im spektralen mittleren IR-Bereich

    Energy Technology Data Exchange (ETDEWEB)

    Mitzschke, Kerstin

    2007-11-01

    Nonlinear optical spectroscopy is a powerful method to study surface or bulk properties of condensed matter. In centrosymmetric materials like silicon even order nonlinear optical processes are forbidden. Besides self-focussing or self phase modulation third-harmonic-generation (THG) is the simplest process that can be studied. This work demonstrates that THG is a adapted non-contact and non-invasive optical method to get information about bulk structures of silicon and Photonic crystals (PC), consisting of silicon. Until now most studies are done in the visible spectral range being limited by the linear absorption losses. So the extension of THG to the IR spectral range is extremely useful. This will allow the investigation of Photonic Crystals, where frequencies near a photonic bandgap are of special interest. 2D- photonic structures under investigation were fabricated via photoelectrochemical etching of the Si (100) wafer (thickness 500 {mu}m) receiving square and hexagonal arranged pores. The typical periodicity of the structures used is 2 {mu}m and the length of the pores reached to 400 {mu}m. Because of stability the photonic structures were superimposed on silicon substrate. The experimental set-up used for the THG experiments generates tuneable picosecond IR pulses (tuning range 1500-4000 cm{sup -1}). The IR-pulse hit the sample either perpendicular to the sample surface or under an angle {theta}. The sample can be rotated (f) around the surface normal. The generated third harmonic is analysed by a polarizer, spectrally filtered by a polychromator and registered by a CCD camera. The setup can be used either in transmission or in reflection mode. Optical transmission and reflection spectra of the Si bulk correspond well with the theoretical description, a 4-fold and a 8-fold dependencies of the azimuth angle resulting in the structure of the x{sup (3)}-tensor of (100)-Si. The situation changes dramatically if the PC with hexagonal structure is investigated

  10. Spectral Methods

    CERN Document Server

    Shen, Jie; Wang, Li-Lian

    2011-01-01

    Along with finite differences and finite elements, spectral methods are one of the three main methodologies for solving partial differential equations on computers. This book provides a detailed presentation of basic spectral algorithms, as well as a systematical presentation of basic convergence theory and error analysis for spectral methods. Readers of this book will be exposed to a unified framework for designing and analyzing spectral algorithms for a variety of problems, including in particular high-order differential equations and problems in unbounded domains. The book contains a large

  11. Magnetic circular dichroism of porphyrin lanthanide M3+ complexes.

    Science.gov (United States)

    Andrushchenko, Valery; Padula, Daniele; Zhivotova, Elena; Yamamoto, Shigeki; Bouř, Petr

    2014-10-01

    Lanthanide complexes exhibit interesting spectroscopic properties yielding many applications as imaging probes, natural chirality amplifiers, and therapeutic agents. However, many properties are not fully understood yet. Therefore, we applied magnetic circular dichroism (MCD) spectroscopy, which provides enhanced information about the underlying electronic structure to a series of lanthanide compounds. The metals in the M(3+) state included Y, La, Eu, Tb, Dy, Ho, Er, Tm, Yb, and Lu; the spectra were collected for selected tetraphenylporphin (TPP) and octaethylporphin (OEP) complexes in chloroform. While the MCD and UV-VIS absorption spectra were dominated by the porphyrin signal, metal binding significantly modulated them. MCD spectroscopy was found to be better suited to discriminate between various species than absorption spectroscopy alone. The main features and trends in the lanthanide series observed in MCD and absorption spectra of the complexes could be interpreted at the Density Functional Theory (DFT) level, with effective core potentials on metal nuclei. The sum over state (SOS) method was used for simulation of the MCD intensities. The combination of the spectroscopy and quantum-chemical computations is important for understanding the interactions of the metals with the organic compounds.

  12. Remote compositional analysis of lunar olivine-rich lithologies with Moon Mineralogy Mapper (M3) spectra

    Science.gov (United States)

    Isaacson, P.J.; Pieters, C.M.; Besse, S.; Clark, R.N.; Head, J.W.; Klima, R.L.; Mustard, J.F.; Petro, N.E.; Staid, M.I.; Sunshine, J.M.; Taylor, L.A.; Thaisen, K.G.; Tompkins, S.

    2011-01-01

    A systematic approach for deconvolving remotely sensed lunar olivine-rich visible to near-infrared (VNIR) reflectance spectra with the Modified Gaussian Model (MGM) is evaluated with Chandrayaan-1 Moon Mineralogy Mapper (M 3) spectra. Whereas earlier studies of laboratory reflectance spectra focused only on complications due to chromite inclusions in lunar olivines, we develop a systematic approach for addressing (through continuum removal) the prominent continuum slopes common to remotely sensed reflectance spectra of planetary surfaces. We have validated our continuum removal on a suite of laboratory reflectance spectra. Suites of olivine-dominated reflectance spectra from a small crater near Mare Moscoviense, the Copernicus central peak, Aristarchus, and the crater Marius in the Marius Hills were analyzed. Spectral diversity was detected in visual evaluation of the spectra and was quantified using the MGM. The MGM-derived band positions are used to estimate the olivine's composition in a relative sense. Spectra of olivines from Moscoviense exhibit diversity in their absorption features, and this diversity suggests some variation in olivine Fe/Mg content. Olivines from Copernicus are observed to be spectrally homogeneous and thus are predicted to be more compositionally homogeneous than those at Moscoviense but are of broadly similar composition to the Moscoviense olivines. Olivines from Aristarchus and Marius exhibit clear spectral differences from those at Moscoviense and Copernicus but also exhibit features that suggest contributions from other phases. If the various precautions discussed here are weighed carefully, the methods presented here can be used to make general predictions of absolute olivine composition (Fe/Mg content). Copyright ?? 2011 by the American Geophysical Union.

  13. Hemopoietic tissue in newts flown aboard Foton M3

    Science.gov (United States)

    Domaratskaya, Elena I.; Almeida, Eduardo; Butorina, Nina N.; Nikonova, Tatyana M.; Grigoryan, Eleonora N.; Poplinskaya, Valentina A.; Souza, Kenneth; Skidmore, Mike

    The effect of 12-day spaceflight aboard the Foton-M3 biosatellite on the hematopoietic tissue of P. waltl newts was studied. These animals used at the same time in regeneration experiments after lens and tail tip amputation. In flight and synchronous groups there were performed video recording, temperature and radiation monitoring and continuous contact (via skin) with thymidine analog BrdU. We took differential blood counts and assessed histologically the liver in the flight (F), basal (BC) and synchronous (SC)control groups of animals. In the peripheral blood, we identified neutrophils, eosinophils, basophils, lymphocytes, and monocytes. Lymphocytes (L) and neutrophils (N) prevailed, accounting for about 60 and 20% of white blood cells, respectively. The spaceflight had no apparent effect on the differential blood count in the F group: neither the L and N contents nor the maturing to mature N - ratio differed from those in the control groups. No significant differences between F, SC and BC groups were observed with respect to the structure of hematopoietic areas and the liver morphology. As in Foton-M2, BrdU labeled cells revealed in blood as well as in the hemopoietic areas of the liver. However, in previous experiments performed at satellites Bion-10 and Foton-M2 the changes in peripheral blood contents were registered in operated F newts, and we supposed it could be the result of additive effects of spaceflight factors and stimulation of reparative potency and stress due to surgical operation. Possibly, the temperature conditions also may provide some influence on blood cell content of newts that belong to poikilothermic animals. Thus, in present experiment F and SC groups were reared in the same temperature regims, whereas it was nearly 3o C differences between SC and F groups exposed on Foton-M2. At the same time as it was found in experiments on Bion-11 and Foton-M2 spaceflight factors did not affect on differential blood counts of intact non

  14. Relativistic electrons high doses at International Space Station and Foton M2/M3 satellites

    Science.gov (United States)

    Dachev, T. P.; Tomov, B.; Matviichuk, Yu.; Dimitrov, Pl.; Bankov, N.

    2009-12-01

    The paper presents observation of relativistic electrons. Data are collected by the Radiation Risk Radiometer-Dosimeters (R3D) B2/B3 modifications during the flights of Foton M2/M3 satellites in 2005 and 2007 as well as by the R3DE instrument at the European Technology Exposure Facility (EuTEF) on the Columbus External Payload Adaptor at the International Space Station (ISS) in the period February 20 - April 28, 2008. On the Foton M2/M3 satellites relativistic electrons are observed more frequently than on the ISS because of higher (62.8°) inclination of the orbit. At both Foton satellites the usual duration of the observations are a few minutes long. On the ISS the duration usually is about 1 min or less. The places of observations of high doses due to relativistic electrons are distributed mainly at latitudes above 50° geographic latitude in both hemispheres on Foton M2/M3 satellites. A very high maximum is found in the southern hemisphere at longitudinal range 0°-60°E. At the ISS the maximums are observed between 45° and 52° geographic latitude in both hemispheres mainly at longitudes equatorward from the magnetic poles. The measured absolute maximums of dose rates generated by relativistic electrons are found to be as follows: 304 μGy h -1 behind 1.75 g cm -2 shielding at Foton M2, 2314 μGy h -1 behind 0.71 g cm -2 shielding at Foton M3 and 19,195 μGy h -1 (Flux is 8363 cm -2 s -1) behind les than 0.4 g cm -2 shielding at ISS.

  15. Spectral Analysis

    CERN Document Server

    Cecconi, Jaures

    2011-01-01

    G. Bottaro: Quelques resultats d'analyse spectrale pour des operateurs differentiels a coefficients constants sur des domaines non bornes.- L. Garding: Eigenfuction expansions.- C. Goulaouic: Valeurs propres de problemes aux limites irreguliers: applications.- G. Grubb: Essential spectra of elliptic systems on compact manifolds.- J.Cl. Guillot: Quelques resultats recents en Scattering.- N. Schechter: Theory of perturbations of partial differential operators.- C.H. Wilcox: Spectral analysis of the Laplacian with a discontinuous coefficient.

  16. In Situ Measurements of Aerosol Mass Concentration and Spectral Absorption at Three Location in and Around Mexico City

    Science.gov (United States)

    Chaudhry, Z.; Martins, V.; Li, Z.

    2006-12-01

    As a result of population growth and increasing industrialization, air pollution in heavily populated urban areas is one of the central environmental problems of the century. As a part of the MILAGRO (Megacity Initiative: Local and Global Research Observations) study, Nuclepore filters were collected in two size ranges (PM10 and PM2.5) at 12 hour intervals at three location in Mexico during March, 2006. Sampling stations were located at the Instituto Mexicano del Petroleo (T0), at the Rancho La Bisnago in the State of Hidalgo (T2) and along the Gulf Coast in Tampico (Tam). Each filter was analyzed for mass concentration, aerosol scattering and absorption efficiencies. Mass concentrations at T0 ranged from 47 to 179 μg/m3 for PM10 with an average concentration of 96 μg/m3, and from 20 to 93 μg/m3 for PM2.5 with an average concentration of 41 μg/m3. Mass concentrations at T2 ranged from 12 to 154 μg/m3 for PM10 with an average concentration of 51 μg/m3, and from 7 to 50 μg/m3 for PM2.5 with an average concentration of 25 μg/m3. Mass concentrations at Tam ranged from 34 to 80 μg/m3 for PM10 with an average concentration of 52 μg/m3, and from 8 to 23 μg/m3 for PM2.5 with an average concentration of 13 μg/m3. While some of the extreme values are likely linked to local emissions, regional air pollution episodes also played important roles. Each of the sampling stations experienced a unique atmospheric condition. The site at T0 was influenced by urban air pollution and dust storms, the site at T2 was significantly less affected by air pollution but more affected by regional dust storms and local dust devils while Tam was influenced by air pollution, dust storms and the natural marine environment. The spectral mass absorption efficiency was measured from 350 to 2500 nm and shows large differences between the absorption properties of soil dust, black carbon, and organic aerosols. The strong spectral differences observed can be related to differences in

  17. Transport coefficients of black MQGP M3-branes

    Energy Technology Data Exchange (ETDEWEB)

    Dhuria, Mansi [Physical Research Laboratory, Theoretical Physics Division, Ahmedabad (India); Misra, Aalok [Indian Institute of Technology, Department of Physics, Roorkee, Uttaranchal (India)

    2015-01-01

    The Strominger-Yau-Zaslow (SYZ) mirror, in the 'delocalised limit' of Becker et al. (Nucl Phys B 702:207, 2004), of N D3-branes, M fractional D3-branes and N{sub f} flavour D7-branes wrapping a non-compact four-cycle in the presence of a black hole (BH) resulting in a non-Kahler resolved warped deformed conifold (NKRWDC) in Mia et al. (Nucl Phys B 839:187, 2010), was carried out in Dhuria and Misra (JHEP 1311:001, 2013) and resulted in black M3- branes. There are two parts in our paper. In the first we show that in the 'MQGP' limit discussed in Dhuria and Misra (JHEP 1311:001, 2013) a finite g{sub s} (and hence expected to be more relevant to QGP), finite g{sub s}M, N{sub f}, g{sub s}{sup 2}MN{sub f} and very large g{sub s}N, and very small (g,M{sup 2})/(N), we have the following. (i) The uplift, if valid globally (like Dasgupta et al., Nucl Phys B 755:21, 2006) for fractional D3 branes in conifolds, asymptotically goes to M5-branes wrapping a two-cycle (homologously a (large) integer sum of two-spheres) in AdS{sub 5} x M{sub 6}. (ii) Assuming the deformation parameter to be larger than the resolution parameter, by estimating the five SU(3) structure torsion (τ) classes W{sub 1,2,3,4,5} we verify that τ element of W{sub 5} in the large-r limit, implying the NKRWDC reduces to a warped Kahler deformed conifold. (iii) The local T{sup 3} of Dhuria and Misra (JHEP 1311:001, 2013) in the large-r limit satisfies the same conditions as the maximal T{sup 2}-invariant special Lagrangian three-cycle of T*S{sup 3} of Ionel and Min-OO (J Math 52(3), 2008), partly justifying use of SYZ-mirror symmetry in the ''delocalised limit'' of Becker et al. (Nucl Phys B 702:207, 2004) in Dhuria and Misra (JHEP 1311:001, 2013). In the second part of the paper, by either integrating out the angular coordinates of the non-compact four-cycle which a D7-brane wraps around, using the Ouyang embedding, in the DBI action of a D7-brane evaluated at infinite

  18. Discovery of a wide planetary-mass companion to the young M3 star GU PSC

    Energy Technology Data Exchange (ETDEWEB)

    Naud, Marie-Eve; Artigau, Étienne; Malo, Lison; Albert, Loïc; Doyon, René; Lafrenière, David; Gagné, Jonathan; Boucher, Anne [Département de physique and Observatoire du Mont-Mégantic, Université de Montréal, Montréal H3C 3J7 (Canada); Saumon, Didier [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Morley, Caroline V. [Department of Astronomy and Astrophysics, University of California, Santa Cruz, CA 95064 (United States); Allard, France; Homeier, Derek [Centre de Recherche Astrophysique de Lyon, UMR 5574 CNRS, Université de Lyon, École Normale Supérieure de Lyon, 46 Allée d' Italie, F-69364 Lyon Cedex 07 (France); Beichman, Charles A.; Gelino, Christopher R., E-mail: naud@astro.umontreal.ca [Infrared Processing and Analysis Center, MS 100-22, California Institute of Technology, Pasadena, CA 91125 (United States)

    2014-05-20

    We present the discovery of a comoving planetary-mass companion ∼42'' (∼2000 AU) from a young M3 star, GU Psc, a likely member of the young AB Doradus Moving Group (ABDMG). The companion was first identified via its distinctively red i – z color (>3.5) through a survey made with Gemini-S/GMOS. Follow-up Canada-France-Hawaii Telescope/WIRCam near-infrared (NIR) imaging, Gemini-N/GNIRS NIR spectroscopy and Wide-field Infrared Survey Explorer photometry indicate a spectral type of T3.5 ± 1 and reveal signs of low gravity which we attribute to youth. Keck/Adaptive Optics NIR observations did not resolve the companion as a binary. A comparison with atmosphere models indicates T {sub eff} = 1000-1100 K and log g = 4.5-5.0. Based on evolution models, this temperature corresponds to a mass of 9-13 M {sub Jup} for the age of ABDMG (70-130 Myr). The relatively well-constrained age of this companion and its very large angular separation to its host star will allow its thorough characterization and will make it a valuable comparison for planetary-mass companions that will be uncovered by forthcoming planet-finder instruments such as Gemini Planet Imager and SPHERE 9.

  19. Magnetic and dynamical photospheric disturbances observed during an M3.2 solar flare

    CERN Document Server

    Kuckein, C; Sainz, R Manso

    2015-01-01

    This letter reports on a set of full-Stokes spectropolarimetric observations in the near infrared He I 10830 A spectral region covering the pre-, flare, and post-flare phases of an M3.2 class solar flare. The flare originated on 2013 May 17 and belonged to active region NOAA 11748. We detected strong He I 10830 A emission in the flare. The red component of the He I triplet peaks at an intensity ratio to the continuum of about 1.86. During the flare, He I Stokes V is substantially larger and appears reversed compared to the usually larger Si I Stokes V profile. The photospheric Si I inversions of the four Stokes profiles reveal the following: (1) the magnetic field strength in the photosphere decreases or is even absent during the flare phase, as compared to the pre-flare phase. However, this decrease is not permanent. After the flare the magnetic field recovers its pre-flare configuration in a short time (i.e., in 30 minutes after the flare). (2) In the photosphere, the line-of-sight velocities show a regular...

  20. Discovery of a wide planetary-mass companion to the young M3 star GU Psc

    CERN Document Server

    Naud, Marie-Eve; Malo, Lison; Albert, Loïc; Doyon, René; Lafrenière, David; Gagné, Jonathan; Saumon, Didier; Morley, Caroline V; Allard, France; Homeier, Derek; Beichman, Charles A; Gelino, Christopher R; Boucher, Anne

    2014-01-01

    We present the discovery of a co-moving planetary-mass companion ~42" (~2000 AU) from a young M3 star, GU Psc, likely member of the young AB Doradus Moving Group (ABDMG). The companion was first identified via its distinctively red i - z color (> 3.5) through a survey made with Gemini-S/GMOS. Follow-up Canada-France-Hawaii Telescope/WIRCam near-infrared (NIR) imaging, Gemini-N/GNIRS NIR spectroscopy and Wide-field Infrared Survey Explorer photometry indicate a spectral type of T3.5+-1 and reveal signs of low gravity which we attribute to youth. Keck/Adaptive Optics NIR observations did not resolve the companion as a binary. A comparison with atmosphere models indicates Teff = 1000-1100 K and logg = 4.5-5.0. Based on evolution models, this temperature corresponds to a mass of 9-13 MJup for the age of ABDMG (70-130 Myr). The relatively well-constrained age of this companion and its very large angular separation to its host star will allow its thorough characterization and will make it a valuable comparison for ...

  1. Spectral-kinetic properties of heterostructures with GaAsSb/InGaAs/GaAs-based quantum wells emitting in the range of 1.0-1.2 {mu}m

    Energy Technology Data Exchange (ETDEWEB)

    Morozov, S. V., E-mail: more@ipm.sci.-nnov.ru; Kryzhkov, D. I.; Aleshkin, V. Ya. [Russian Academy of Sciences, Institute for Physics of Microstructures (Russian Federation); Zvonkov, B. N.; Vikhrova, O. I. [Nizhni Novgorod State University, Physical-Technical Research Institute (Russian Federation)

    2013-11-15

    The spectral-kinetic properties of heterostructures with GaAs/GaAsSb-based and GaAsSb/InGaAs/GaAs-based quantum wells, emitting in the range of 1.0-1.2 {mu}m are studied with picosecond and nanosecond temporal resolution. Intense photoluminescence in the GaAsSb/InGaAs/GaAs structure, as well as an increase in the photoluminescence wavelength by a factor of 2.5 and a shift of the location of the maximum of the peak ({approx}100 meV) to the longer-wavelength region were observed up to room temperature. It is established that as the molar fraction of Sb and the thickness of the InGaAs layer increase, the energy of the fundamental transition decreases by a factor of 140 meV compared with the GaAsSb/InGaAs/GaAs structure with a lower Sb content and a smaller thickness of the InGaAs layer. At 300 K, the emission wavelength of such a structure was 1.18 {mu}m. In addition, an increase in the thickness of the InGaAs layer led to an increase in the room-temperature photoluminescence intensity by a factor of 60, which is associated with a decrease in the energy of the fundamental state for electrons in the InGaAs layer and, consequently, to larger electron localization and smaller temperature quenching of photoluminescence.

  2. Effects of Modulating M3 Muscarinic Receptor Activity on Azoxymethane-Induced Liver Injury in Mice

    OpenAIRE

    2013-01-01

    Previously, we reported that azoxymethane (AOM)-induced liver injury is robustly exacerbated in M3 muscarinic receptor (M3R)-deficient mice. We used the same mouse model to test the hypothesis that selective pharmacological modulation of M3R activity regulates the liver injury response. Initial experiments confirmed that giving a selective M3R antagonist, darifenacin, to AOM-treated mice mimicked M3R gene ablation. Compared to vehicle controls, mice treated with the M3R antagonist had reduced...

  3. Spectral Ranking

    CERN Document Server

    Vigna, Sebastiano

    2009-01-01

    This note tries to attempt a sketch of the history of spectral ranking, a general umbrella name for techniques that apply the theory of linear maps (in particular, eigenvalues and eigenvectors) to matrices that do not represent geometric transformations, but rather some kind of relationship between entities. Albeit recently made famous by the ample press coverage of Google's PageRank algorithm, spectral ranking was devised more than fifty years ago, almost exactly in the same terms, and has been studied in psychology and social sciences. I will try to describe it in precise and modern mathematical terms, highlighting along the way the contributions given by previous scholars.

  4. Spectral Tagging

    Energy Technology Data Exchange (ETDEWEB)

    Smartt, Heidi A. [Sandia National Laboratories (United States)

    2003-05-01

    This research examines the feasibility of spectral tagging, which involves modifying the spectral signature of a target, e.g. by mixing an additive with the target's paint. The target is unchanged to the human eye, but the tag is revealed when viewed with a spectrometer. This project investigates a layer of security that is not obvious, and therefore easy to conceal. The result is a tagging mechanism that is difficult to counterfeit. Uniquely tagging an item is an area of need in safeguards and security and non-proliferation. The powdered forms of the minerals lapis lazuli and olivine were selected as the initial test tags due to their availability and uniqueness in the visible to near-infrared spectral region. They were mixed with paints and applied to steel. In order to verify the presence of the tags quantitatively, the data from the spectrometer was input into unmixing models and signal detection algorithms. The mixture with the best results was blue paint mixed with lapis lazuli and olivine. The tag had a 0% probability of false alarm and a 100% probability of detection. The research proved that spectral tagging is feasible, although certain tag/paint mixtures are more detectable than others.

  5. High temperature EPR study of the M3Fe4V6O24 (M = Cu, Zn, Mg and Mn

    Directory of Open Access Journals (Sweden)

    Guskos Niko

    2016-09-01

    Full Text Available Electron paramagnetic resonance (EPR spectra of M3Fe4V6O24 (M = Cu, Zn, Mg and Mn compounds in high temperature range (293 K to 493 K have been investigated. The role of magnetic (Cu, Mn and non-magnetic (Zn, Mg ions in M3Fe4V6O24 structure in formation of magnetic resonance spectra was studied. Temperature dependence of EPR parameters: resonance field, linewidth and integrated intensity were examined. Similarities and differences in temperature behavior of these parameters has been discussed in terms of different relaxation mechanisms and magnetic interactions in the spin systems. An important role of additional magnetic ions (M = Mn or Cu in the M3Fe4V6O24 structure has been identified and its consequences considered.

  6. Exception Processing of Cortex-M3%Cortex-M3的异常处理机制研究

    Institute of Scientific and Technical Information of China (English)

    方安平; 蔡俊宇

    2009-01-01

    详细阐述Cortex-M3异常的分类、优先级、进入和退出,以及在Cortex-M3异常处理机制中使用的新技术--迟到(late-arriving)和尾链(tail-chaining);最后,比较Cortex-M3和ARM7异常控制机制的区别,并量化分析迟到和尾链技术在异常处理中的优越性.

  7. Half lives of spherical proton emitters using density dependent M3Y interaction

    CERN Document Server

    Chowdhury, P R; Basu, D N

    2005-01-01

    The proton radioactivity lifetimes of spherical proton emitters from the ground and the isomeric states are calculated using the microscopic nucleon-nucleus interaction potentials. The daughter nuclei density distributions are folded with a realistic density dependent M3Y effective interaction supplemented by a zero-range pseudo-potential. The density dependence parameters of the interaction are extracted from the nuclear matter calculations. The saturation energy per nucleon used for nuclear matter calculations is determined from the co-efficient of the volume term of Bethe-Weizsacker mass formula which is evaluated by fitting the recent experimental and estimated atomic mass excesses from Audi-Wapstra-Thibault atomic mass table by minimizing the mean square deviation. The quantum mechanical tunneling probability is calculated within the WKB approximation. Spherical charge distributions are used for calculating the Coulomb interaction potentials. These calculations provide good estimates for the observed pro...

  8. The BIOPAN experiment MARSTOX II of the FOTON M-3 mission

    Science.gov (United States)

    Rettberg, P.; Moeller, R.; Rabbow, E.; Panitz, C.; Horneck, G.; Meyer, C.; Lammer, H.; Douki, T.; Cadet, J.

    2008-09-01

    The experiment MARSTOX II on FOTON M-3 mission (September 14 - 26, 2007) was a further step in the study of the Responses of Organisms to the Martian Environment (ROME) which already started with first ground-based experiments in Mars simulation chambers and with the space experiment MARSTOX I, flown in 2005 in the ESA facility BIOPAN (Fig. 1) on FOTON M-2. The survivability of bacterial spores of B. subtilis, a well-characterized model system for highly resistant microorganisms, was investigated under the extreme environmental conditions as they exist on the surface of Mars. By use of exterrestrial UV radiation and cut-off filters the photoprotection and potential UV-phototoxicity of different minerals of the Martian soil were investigated.In MARSTOX II two further aspects were addressed (i) the influence of different concentrations of dust in the Martian atmosphere, which change the solar irradiance on the surface significantly compared to vacuum exposure under the same conditions (experiment parts 'DUST MARS' and 'DUST SPACE'), and (ii) the survivability of spores under martian atmosphere and pressure exposed to a mars-like spectral irradiance compared to vacuum exposure under the same conditions (experiment parts 'MIXED MARS' and 'MIXED SPACE') (Fig. 2 and 3). After exposure to space during the FOTON M-3 mission the sample analysis was performed at CEA in Grenoble, F, and at DLR in Cologne, D, together with parallel samples from the corresponding ground control experiment performed in the space simulation facilities at DLR. As biological endpoints in these investigations survival and UV-induced DNAphotoproducts were analysed.From the results of MARSTOX II the following conclusions can be drawn: (i) Spores mixed with martian soil analogue are protected only to a low degree against UV radiation. The protective effect of several defined layers of spores mixed with Martian soil analogue were quantified. (ii) The two investigated martian soil analogues, MRS07 (47

  9. Correction of the recording artifacts and detection of the functional deviations in ECG by means of syndrome decoding with an automatic burst error correction of the cyclic codes using periodograms for determination of code component spectral range

    Directory of Open Access Journals (Sweden)

    Evgenie D. Adamoviс

    2016-05-01

    Full Text Available Aims This paper describes a novel approach to the analysis of electrocardiographic data based on the consideration of the repetitive P, Q, R, S, T sequences as cyclic codes. In Part I we introduce a principle similar to the syndrome decoding using the control numbers, which allows correcting the noise combinations. Materials and methods We propose to apply the burst-error-correcting algorithms for automatic detection of the ECG artifacts and the functional abnormalities, including those compared to the reference model. Our approach is compared to the symbolic dynamics methods in cardiology practice. During the automated search of the code components (i.e. point values and spectral ranges one-to-one corresponding to P, Q, R, S, T considered in Part II, the authors apply the Lomb-Scargle periodogram method with the phase control which allows to determine the code components not only from the main harmonics, but also using the sidebands, avoiding the phase errors. Results The results of the method testing on rats with the heart failure using a simplified telemetric recording from the implantable chips are given in Part III. A complete independence of the results of the determination of the code points (fingerprints from the variables for which the calculation is performed is shown. We also prove the robustness of the above approach with respect to the most types of the non-adaptive filtration. Conclusion The above method can be useful not only for experimental medicine, but also for veterinary and clinical diagnostic practice. This method is adequately reproducable both on animals and human ECG, except for some constant values.

  10. Spectral Predictors

    Energy Technology Data Exchange (ETDEWEB)

    Ibarria, L; Lindstrom, P; Rossignac, J

    2006-11-17

    Many scientific, imaging, and geospatial applications produce large high-precision scalar fields sampled on a regular grid. Lossless compression of such data is commonly done using predictive coding, in which weighted combinations of previously coded samples known to both encoder and decoder are used to predict subsequent nearby samples. In hierarchical, incremental, or selective transmission, the spatial pattern of the known neighbors is often irregular and varies from one sample to the next, which precludes prediction based on a single stencil and fixed set of weights. To handle such situations and make the best use of available neighboring samples, we propose a local spectral predictor that offers optimal prediction by tailoring the weights to each configuration of known nearby samples. These weights may be precomputed and stored in a small lookup table. We show that predictive coding using our spectral predictor improves compression for various sources of high-precision data.

  11. MAGNETIC AND DYNAMICAL PHOTOSPHERIC DISTURBANCES OBSERVED DURING AN M3.2 SOLAR FLARE

    Energy Technology Data Exchange (ETDEWEB)

    Kuckein, C. [Leibniz-Institut für Astrophysik Potsdam (AIP), An der Sternwarte 16, D-14482, Potsdam (Germany); Collados, M.; Sainz, R. Manso, E-mail: ckuckein@aip.de [Instituto de Astrofísica de Canarias (IAC), Vía Láctea s/n, E-38205, La Laguna, Tenerife (Spain)

    2015-02-01

    This Letter reports on a set of full-Stokes spectropolarimetric observations in the near-infrared He i 10830 Å spectral region covering the pre-flare, flare, and post-flare phases of an M3.2 class solar flare. The flare originated on 2013 May 17 and belonged to active region NOAA 11748. We detected strong He i 10830 Å emission in the flare. The red component of the He i triplet peaks at an intensity ratio to the continuum of about 1.86. During the flare, He i Stokes V is substantially larger and appears reversed compared to the usually larger Si i Stokes V profile. The photospheric Si i inversions of the four Stokes profiles reveal the following: (1) the magnetic field strength in the photosphere decreases or is even absent during the flare phase, as compared to the pre-flare phase. However, this decrease is not permanent. After the flare, the magnetic field recovers its pre-flare configuration in a short time (i.e., 30 minutes after the flare). (2) In the photosphere, the line of sight velocities show a regular granular up- and downflow pattern before the flare erupts. During the flare, upflows (blueshifts) dominate the area where the flare is produced. Evaporation rates of ∼10{sup −3} and ∼10{sup −4} g cm{sup −2} s{sup −1} have been derived in the deep and high photosphere, respectively, capable of increasing the chromospheric density by a factor of two in about 400 s.

  12. Doping Asymmetry Problem in ZnO: Current Status and Outlook. A Review of Experimental and Theoretical Efforts Focused on Achieving P-Type ZnO Suitable for Light-Emitting Optoelectronic Devices for the Blue/Ultraviolet Spectral Range

    Science.gov (United States)

    2009-04-24

    Richmond VA 23284 USA. (e-mail: hmorkoc@vcu.edu). Donald Silversmith is with the Air Force Office of Scientific Research, Arlington, VA 22203 USA (e...for light-emitting optoelectronic devices for the blue/ultraviolet spectral range. Vitaliy Avrutin, Donald Silversmith , Fellow, IEEE, and Hadis Morkoç

  13. Different Characteristics of the Bright Branches of the Globular Clusters M3 and M13

    CERN Document Server

    Cho, D H; Jeon, Y B; Sim, K J; Cho, Dong-Hwan; Lee, Sang-Gak; Jeon, Young-Beom; Sim, Kyung Jin

    2005-01-01

    We carried out wide-field BVI CCD photometric observations of the GCs M3 and M13 using the BOAO 1.8 m telescope equipped with a 2K CCD. We present CMDs of M3 and M13. We have found AGB bumps at V = 14.85 for M3 at V = 14.25 for M13. It is found that AGB stars in M3 are more concentrated near the bump, while those in M13 are scattered along the AGB sequence. We identified the RGB bump of M3 at V = 15.50 and that of M13 at V = 14.80. We have estimated the ratios R and R2 for M3 and M13 and found that of R for M3 is larger than that for M13 while R2's for M3 and M13 are similar when only normal HB stars are used in R and R2 for M13. However, we found that R's for M3 and M13 are similar while R2 for M3 is larger than that for M13 when all the HB stars are included in R and R2 for M13. We have compared the observed RGB LFs of M3 and M13 with the theoretical RGB LF of Bergbusch & VandenBerg at the same radial distances from the cluster centers as used in R and R2 for M3 and M13. We found "extra stars" belonging...

  14. Second Parameter Effects in and between M3 and Palomar 3

    CERN Document Server

    Catelan, M; Ferraro, F R

    2001-01-01

    We study the globular clusters M3 and Palomar 3 as a "second parameter (2ndP) pair," showing that: i) M3 has a surprisingly strong *internal* 2ndP; ii) The dispersion in mass on the Pal 3 horizontal branch (HB) is intrinsically very small, leading to the most apparent differences in HB morphology between M3 and Pal 3; iii) Ignoring the difference in HB mass dispersion between M3 and Pal 3, their relative HB types can be accounted for by a fairly small difference in age, of order 0.5-1 Gyr.

  15. Design Essentials of 80 m3 Diluted Acetaldehyde Storage Tank%浅谈80 m3稀乙醛储槽设计要点

    Institute of Scientific and Technical Information of China (English)

    白春山; 刘文元

    2009-01-01

    Combination 80 m3 thin acetaldehyde tank design, the paper focused on low-pressure tank-top cans bearing ring, tank walls, tank top and anchor set design and the method of calculating and comparing the general design of storage tanks were introduced.%结合80 m3稀乙醛储槽的设计,着重介绍低压储罐罐顶承压环、罐壁、罐顶以及锚栓设置的设计及其计算方法,并与一般储罐设计进行比较.

  16. Effects of Modulating M3 Muscarinic Receptor Activity on Azoxymethane-Induced Liver Injury in Mice

    Science.gov (United States)

    Khurana, Sandeep; Jadeja, Ravirajsinh; Twadell, William; Cheng, Kunrong; Rachakonda, Vikrant; Saxena, Neeraj; Raufman, Jean-Pierre

    2013-01-01

    Previously, we reported that azoxymethane (AOM)-induced liver injury is robustly exacerbated in M3 muscarinic receptor (M3R)-deficient mice. We used the same mouse model to test the hypothesis that selective pharmacological modulation of M3R activity regulates the liver injury response. Initial experiments confirmed that giving a selective M3R antagonist, darifenacin, to AOM-treated mice mimicked M3R gene ablation. Compared to vehicle controls, mice treated with the M3R antagonist had reduced survival and increased liver nodularity and fibrosis. We next assessed AOM-induced liver injury in mice treated with a selective M3R agonist, pilocarpine. After pilocarpine treatment, stimulation of post-M3R signaling in the liver was evidenced by ERK and AKT activation. In contrast to the damaging effects of the M3R antagonist, administering pilocarpine to AOM-treated mice significantly attenuated hepatic stellate cell activation, collagen deposition, bile ductule proliferation, and liver fibrosis and nodularity. As anticipated from these findings, livers from pilocarpine-treated mice exhibited reduced expression of key players in fibrosis (α1 collagen, α-smooth muscle actin, TGF-β1, PGDF, TGF-β1R, PGDFR) and decreased mRNA levels for molecules that regulate extracellular matrix formation (TIMP-1, TIMP-2, MMP-2, MMP-13). Cleaved caspase-3, nitrotyrosine and BrdU immunostaining provided evidence that pilocarpine treatment reduced hepatocyte apoptosis and oxidative stress, while increasing hepatocyte proliferation. Collectively, these findings identify several downstream mechanisms whereby M3R activation ameliorates toxic liver injury. These novel observations provide a proof-of-principle that selectively stimulating M3R activation to prevent or diminish liver injury is a therapeutic strategy worthy of further investigation. PMID:23707755

  17. Scale-up of industrial biodiesel production to 40 m3using a liquid lipase formulation

    DEFF Research Database (Denmark)

    Price, Jason; Nordblad, Mathias; Martel, Hannah H.

    2016-01-01

    In this work, we demonstrate the scale-up from an 80 L fed-batch scale to 40 m3 along with the design of a 4 m3continuous process for enzymatic biodiesel production catalysed by NS-40116 (a liquid formulation of a modified Thermomyces lanuginosus lipase). Based on the analysis of actual pilot pla...

  18. Residual stress in a M3:2 PM high speed steel; effect of mechanical loading

    DEFF Research Database (Denmark)

    Højerslev, Christian; Odén, Magnus; Carstensen, Jesper V.;

    2001-01-01

    X-ray lattice strains were investigated in an AISI M3:2 PM high-speed steel in the as heat treated condition and after exposure to alternating mechanical load. The volume changes during heat treatment were monitored with dilatometry. Hardened and tempered AISI M3:2 steel consists of tempered lath...

  19. [Handling and maintenance of gerbils during the spacecraft Foton-M3 mission].

    Science.gov (United States)

    Soldatov, P E; Smirnov, I A; Il'in, E A; Gur'eva, T S; Mednikova, E I; Smolenskaia, T S; Lysenko, L A; Kaminskaia, E V

    2009-01-01

    Pressurized low-sized module Kontur with an independent life support system (LSS) was developed by the Institute of Biomedical Problems cooperatively with the Special Design Bureau of Experimental Equipment to house gerbils (Meriones unguiculatus) aboard robotic technology-purpose spacecraft. Design of the module precludes pollution of the environment The fully equipped module weighs 69 kg; average daily power consumption is 62 watts. The environmental parameters for 12 animals flown on Foton-M3 in the period of September 14-26, 2007 were controlled within the following ranges: pO2 - 143-156 mm Hg, (mean 150 mm Hg), pCO2 - 0.76 mm Hg maximum (mean 0.64 mm Hg), temperature - 23-28 degrees C (mean 26.7 degrees C), relative humidity - 29% and 57% at the beginning and end of the flight, respectively (mean 39%). The animals consumed the palletized food prepared of natural products with a moisture content of approx. 20%. The day-night periods were 12 hrs. long. The daytime video recording of the animals went on continuously in the throughout the flight. The experiment showed that the module meets the requirements of experiments with mammals aboard returnable robotic spacecraft and piloted space stations. At the moment, the model is being redesigned for a 30-day BION-M1 mission.

  20. A spectral invariant representation of spectral reflectance

    Science.gov (United States)

    Ibrahim, Abdelhameed; Tominaga, Shoji; Horiuchi, Takahiko

    2011-03-01

    Spectral image acquisition as well as color image is affected by several illumination factors such as shading, gloss, and specular highlight. Spectral invariant representations for these factors were proposed for the standard dichromatic reflection model of inhomogeneous dielectric materials. However, these representations are inadequate for other characteristic materials like metal. This paper proposes a more general spectral invariant representation for obtaining reliable spectral reflectance images. Our invariant representation is derived from the standard dichromatic reflection model for dielectric materials and the extended dichromatic reflection model for metals. We proof that the invariant formulas for spectral images of natural objects preserve spectral information and are invariant to highlights, shading, surface geometry, and illumination intensity. It is proved that the conventional spectral invariant technique can be applied to metals in addition to dielectric objects. Experimental results show that the proposed spectral invariant representation is effective for image segmentation.

  1. COOLING METHOD OF SILUMINA CASTINGS AK15M3 AT VERTICAL CENTRIFUGAL CASTING

    Directory of Open Access Journals (Sweden)

    V. Yu. Stecenko

    2013-01-01

    Full Text Available The way of cooling of castings from silumin AK15M3 is developed at the vertical centrifugal casting, enabling to receive bimetallic blanks with high-disperse eutectic and hypereutectic microstructures and minimal allowance for machining.

  2. Complete Genome Sequence of the Novel Leech Symbiont Mucinivorans hirudinis M3T

    OpenAIRE

    Nelson, Michael C.; Bomar, Lindsey; Graf, Joerg

    2015-01-01

    Mucinivorans hirudinis M3T was isolated from the digestive tract of the medicinal leech, Hirudo verbana, and is the type species of a new genus within the Rikenellaceae. Here, we report the complete annotated genome sequence of this bacterium.

  3. Complete Genome Sequence of the Novel Leech Symbiont Mucinivorans hirudinis M3T.

    Science.gov (United States)

    Nelson, Michael C; Bomar, Lindsey; Graf, Joerg

    2015-02-05

    Mucinivorans hirudinis M3(T) was isolated from the digestive tract of the medicinal leech, Hirudo verbana, and is the type species of a new genus within the Rikenellaceae. Here, we report the complete annotated genome sequence of this bacterium.

  4. spectral-cube: Read and analyze astrophysical spectral data cubes

    Science.gov (United States)

    Robitaille, Thomas; Ginsburg, Adam; Beaumont, Chris; Leroy, Adam; Rosolowsky, Erik

    2016-09-01

    Spectral-cube provides an easy way to read, manipulate, analyze, and write data cubes with two positional dimensions and one spectral dimension, optionally with Stokes parameters. It is a versatile data container for building custom analysis routines. It provides a uniform interface to spectral cubes, robust to the wide range of conventions of axis order, spatial projections, and spectral units that exist in the wild, and allows easy extraction of cube sub-regions using physical coordinates. It has the ability to create, combine, and apply masks to datasets and is designed to work with datasets too large to load into memory, and provide basic summary statistic methods like moments and array aggregates.

  5. Posttranslational modifications of human M3 muscarinic acetylcholine receptor: zooming in its functional implications

    OpenAIRE

    Romero Fernández, Wilber

    2011-01-01

    The human M3 muscarinic acetylcholine receptor (M3R) regulates many important physiological roles in the central and peripheral nervous systems, and it is involved in the pathophysiology of several neurodegenerative and autoimmune diseases, representing attractive potential pharmacological target for intervention. However, the lack of structural information on this receptor hampered the development of new potent antagonist with increased selectivity and lower side effects. Such structural inf...

  6. M3B: A coarse grain model for the simulation of oligosaccharides and their water mixtures.

    Science.gov (United States)

    Goddard, William A.; Cagin, Tahir; Molinero, Valeria

    2003-03-01

    Water and sugar dynamics in concentrated carbohydrate solutions is of utmost importance in food and pharmaceutical technology. Water diffusion in concentrated sugar mixtures can be slowed down many orders of magnitude with respect to bulk water [1], making extremely expensive the simulation of these systems with atomistic detail for the required time-scales. We present a coarse grain model (M3B) for malto-oligosaccharides and their water mixtures. M3B speeds up molecular dynamics simulations about 500-1000 times with respect to the atomistic model while retaining enough detail to be mapped back to the atomistic structures with low uncertainty in the positions. The former characteristic allows the study of water and carbohydrate dynamics in supercooled and polydisperse mixtures with characteristic time scales above the nanosecond. The latter makes M3B well suited for combined atomistic-mesoscale simulations. We present the parameterization of M3B force field for water and a family of technologically relevant glucose oligosaccharides, the alpha-(1->4) glucans. The coarse grain force field is completely parameterized from atomistic simulations to reproduce the density, cohesive energy and structural parameters of amorphous sugars. We will show that M3B is capable to describe the helical character of the higher oligosaccharides, and that the water structure in low moisture mixtures shows the same features obtained with the atomistic and M3B models. [1] R Parker, SG Ring: Carbohydr. Res. 273 (1995) 147-55.

  7. Spectral Variability of FSRQs

    Indian Academy of Sciences (India)

    Minfeng Gu; Y. L. Ai

    2011-03-01

    The optical variability of 29 flat spectrum radio quasars in SDSS Stripe 82 region are investigated by using DR7 released multi-epoch data. All FSRQs show variations with overall amplitude ranging from 0.24 mag to 3.46 mag in different sources. About half of FSRQs show a bluer-when-brighter trend, which is commonly observed for blazars. However, only one source shows a redder-when-brighter trend, which implies it is rare in FSRQs. In this source, the thermal emission may be responsible for the spectral behaviour.

  8. Spectral Decomposition Algorithm (SDA)

    Data.gov (United States)

    National Aeronautics and Space Administration — Spectral Decomposition Algorithm (SDA) is an unsupervised feature extraction technique similar to PCA that was developed to better distinguish spectral features in...

  9. New M+, M3+-arsenates – the framework structures of AgM3+(HAsO42 (M3+ = Al, Ga and M+GaAs2O7 (M+ = Na, Ag

    Directory of Open Access Journals (Sweden)

    Karolina Schwendtner

    2017-05-01

    Full Text Available The crystal structures of hydrothermally synthesized silver(I aluminium bis[hydrogen arsenate(V], AgAl(HAsO42, silver(I gallium bis[hydrogen arsenate(V], AgGa(HAsO42, silver gallium diarsenate(V, AgGaAs2O7, and sodium gallium diarsenate(V, NaGaAs2O7, were determined from single-crystal X-ray diffraction data collected at room temperature. The first two compounds are representatives of the MCV-3 structure type known for KSc(HAsO42, which is characterized by a three-dimensional anionic framework of corner-sharing alternating M3+O6 octahedra (M = Al, Ga and singly protonated AsO4 tetrahedra. Intersecting channels parallel to [101] and [110] host the Ag+ cations, which are positionally disordered in the Ga compound, but not in the Al compound. The hydrogen bonds are relatively strong, with O...O donor–acceptor distances of 2.6262 (17 and 2.6240 (19 Å for the Al and Ga compounds, respectively. The two diarsenate compounds are representatives of the NaAlAs2O7 structure type, characterized by an anionic framework topology built of M3+O6 octahedra (M = Al, Ga sharing corners with diarsenate groups, and M+ cations (M = Ag hosted in the voids of the framework. Both structures are characterized by a staggered conformation of the As2O7 groups.

  10. 3 800 m3耙吸挖泥船的HVAC设计%HVAC design for a 3 800 m3 trailing suction dredger

    Institute of Scientific and Technical Information of China (English)

    戴菁; 赵骊; 陈维茂

    2007-01-01

    挖泥船的需求量与日俱增,逐渐形成系列船型.通过介绍3 800 m3耙吸挖泥船的HVAC设计系统,与以往挖泥船型比较,以及用户的评价,指出该船的空调系统设计思想和方法上的优点,为后续船提供了有益的参考.

  11. Muscarinic M3 receptors on structural cells regulate cigarette smoke-induced neutrophilic airway inflammation in mice

    NARCIS (Netherlands)

    Kistemaker, Loes E.M.; van Os, Ronald P.; Dethmers-Ausema, Albertina; Bos, I. Sophie T.; Hylkema, Machteld N.; van den Berge, Maarten; Hiemstra, Pieter S; Wess, Jürgen; Meurs, Herman; Kerstjens, Huib A.M.; Gosens, Reinoud

    2015-01-01

    Anticholinergics, blocking the muscarinic M-3 receptor, are effective bronchodilators for patients with chronic obstructive pulmonary disease. Recent evidence from M-3 receptor-deficient mice (M3R-/-) indicates that M-3 receptors also regulate neutrophilic inflammation in response to cigarette smoke

  12. Design of USB smart card reader based on Cortex-M3%基于Cortex-M3的智能卡USB读卡器设计

    Institute of Scientific and Technical Information of China (English)

    李冬霞; 张雪庆

    2010-01-01

    为了提高智能卡系统的通信速度和中断响应速度,设计了基于Cortex-M3和USB接口的智能卡读卡器系统.设计中采用具有ARM Cortex-M3内核的STM32F103R6T6等芯片进行相关的硬件设计,分别使用Keil和Visual C++6.0进行读卡器固件子系统程序和PC端子系统驱动程序开发,在此基础上,专门设计了测试程序用于测试系统的正确性和有效性.实验结果表明,该智能卡读卡器系统可实现计算机与智能卡的准确,高效通信.

  13. Renovation of stirring system in 300m3 L-lysine fermentor%300m3赖氨酸发酵罐搅拌系统改造

    Institute of Scientific and Technical Information of China (English)

    王远海

    2012-01-01

    以加强传质混合为目的提出300m3赖氨酸发酵罐搅拌系统改造方案,采用计算流体力学(CFD)数值模拟方法分析了搅拌系统轴功率、流型、传质混合能力,成功指导了搅拌系统改造,在电流增大的情况下,平均单罐产量提高2.44t,平均糖酸转化率提高约1个百分点.%To strengthen mass transfer and mixing for purpose, the reform scheme of stirring system in 300m3 L-lysine fermentor was proposed, CFD (Computational Fluid Dynamics) numerical simulation was used in analysing shaft power, flow pattern, mass transfer mixing ability of the stirring system, when current increased, the fermentation yield and L-lysine acid conversion rate of sugar was 2.44t and about 1% higher than the fermentor which not renovated.

  14. M3-receptor activation counteracts opioid-mediated apneusis, but the apneusis per se is not necessarily related to an impaired M3 mechanism in rats.

    Science.gov (United States)

    Niwa, Yuka; Haji, Akira

    2011-11-07

    Morphine slows the respiratory cycle due to a predominant prolongation of inspiration (apneusis) by postponing the spontaneous termination of inspiration (inspiratory off-switching). The present study investigates whether the morphine-induced apneusis results from impairment of cholinergic mechanisms in the central respiratory network. The efferent discharge was recorded from the phrenic nerve in artificially ventilated and anesthetized rats with vagotomy. All drugs were injected intravenously. The phrenic nerve displayed an augmenting discharge during inspiration and arrest of discharge during expiration in normal condition. Administration of morphine (0.3-10.0mg/kg) dose-dependently provoked apneusis characterized by a long-lasting, plateau inspiratory discharge of the phrenic nerve. It shortened the expiratory duration. Subsequent administration of physostigmine (0.1mg/kg) restored the morphine-induced apneusis to eupnea with a partial recovery of the augmenting inspiratory discharge. This modification of physostigmine was blocked by a non-specific muscarinic antagonist scopolamine (3.0mg/kg), leading to re-prolongation of inspiration. A similar antagonism was affected by an antagonist of M3 cholinergic receptors, 4-diphenylacetoxy-N-methylpiperidine methiodide (4-DAMP, 1.0 and 10.0mg/kg) but not by an antagonist of M1 cholinergic receptors, pirenzepine (1.0 and 10.0mg/kg). These results demonstrate that the activation of endogenous M3 cholinergic mechanisms counteracts the morphine-induced apneusis. Copyright © 2011 Elsevier Inc. All rights reserved.

  15. The application of pentaprism scanning technology on the manufacturing of M3MP

    Science.gov (United States)

    Qi, Erhui; Hu, Haixiang; Hu, Haifei; Cole, Glen; Luo, Xiao; Ford, Virginia; Zhang, Xuejun

    2016-10-01

    The PSS (pentaprism scanning system) has advantages of simple structure, needless of reference flat, be able of on-site testing, etc, it plays an important role in large flat reflective mirror's manufacturing, especially the high accuracy testing of low order aberrations. The PSS system measures directly the slope information of the tested flat surface. Aimed at the unique requirement of M3MP, which is the prototype mirror of the tertiary mirror in TMT (Thirty Meter Telescope) project, this paper analyzed the slope distribution of low order aberrations, power and astigmatism, which is very important in the manufacturing process of M3MP. Then the sample route lines of PSS are reorganized and new data process algorism is implemented. All this work is done to improve PSS's measure sensitivity of power and astigmatism, for guiding the manufacturing process of M3MP.

  16. Muscarinic M3 receptor subtype gene expression in the human heart.

    Science.gov (United States)

    Hellgren, I; Mustafa, A; Riazi, M; Suliman, I; Sylvén, C; Adem, A

    2000-01-20

    The heart is an important target organ for cholinergic function. In this study, muscarinic receptor subtype(s) in the human heart were determined using reverse transcription-polymerase chain reaction. Our results demonstrated muscarinic receptor M2 and M3 subtype RNA in left/right atria/ventricles of donor hearts. Receptor autoradiography analysis using selective muscarinic ligands indicated an absence of M1 receptor subtype in the human heart. The level of muscarinic receptor binding in atria was two to three times greater than in ventricles. Our results suggest that muscarinic receptors in the human heart are of the M2 and M3 subtypes. This is the first report of M3 receptors in the human myocardium.

  17. M3 User's Manual. Version 3.0

    Energy Technology Data Exchange (ETDEWEB)

    Laaksoharju, Marcus (Geopoint AB, Sollentuna (Sweden)); Skaarman, Erik (Abscondo Utveckling, Bromma (Sweden)); Gomez, Javier B. (Univ. of Zaragoza (Spain). Geochemical modelling Group); Gurban, Ioana (3D Terra (Canada))

    2006-07-15

    This report describes the Multivariate Mixing and Mass balance calculations (M3). This new method and computer code is developed to trace the mixing and reaction processes in the groundwater. The aim of the M3 concept is to decode the often hidden and complex information gathered in the groundwater analytical data. The manual presents shortly the theory and practice behind the M3 method. The M3 computer code is also presented and emphasis is put on the reference manual. This includes detailed reference to the M3 program's abilities and limitations, installation procedures and all functions and operations that the program can perform. It also describes sample cases of how the program is used to analyse a test data set. This guide is part of the Help Files distributed together with M3. Two accompanying reports cover other aspects: - Concepts, Methods, and Mathematical Formulation, gives a complete description of the mathematical framework of M3 and introduces concepts and methods useful for the end user. - M3 version 3.0: Verification and Validation, gathers a collection of validation and verification exercises, designed to test each part of M3 code and to build confidence in its methodology. The M3 method has been tested and modified over several years. The development work has been supported by the Swedish Nuclear Fuel and Waste Management Company (SKB). The main test site for the model was the underground Aespoe Hard Rock Laboratory (HRL). The examples used in this manual are from a Aespoe international groundwater modelling co-operation project where one of the tools used was M3. The M3 concept has been applied on the data from SKB's site investigation programme and in data from Canada, Japan, Jordan, Gabon and Finland. The groundwater composition is a result of mixing processes and water-rock interaction. Standard groundwater models based on thermodynamic laws may not be applicable in a normal temperature groundwater system where equilibrium with many

  18. A Discussion of the High Energy Density Primary Battery Employed in the FOTON M3 Mission

    Science.gov (United States)

    Bennetti, A.; Reece, D.; Spurrett, R.; Schautz, M.; Green, K.

    2008-09-01

    In 2005, ABSL Space Products (ABSL) was contracted by QinetiQ to deliver the lithium sulfuryl chloride primary battery system for the FOTON M3 ESA (European Space Agency) mission. FOTON M3 was led by the ESA Directorate of Human Spaceflight & Exploration and carried a number of materials science, fluid physics and biology experiments as well as technology demonstration payloads. A number of the experiments required a very high energy density primary battery power source. This battery was manufactured by ABSL, and the mission was successfully completed in September 2007 following a twelve days orbiting in Low Earth Orbit (LEO).

  19. Development of RT-components for the M-3 Strawberry Harvesting Robot

    Science.gov (United States)

    Yamashita, Tomoki; Tanaka, Motomasa; Yamamoto, Satoshi; Hayashi, Shigehiko; Saito, Sadafumi; Sugano, Shigeki

    We are now developing the strawberry harvest robot called “M-3” prototype robot system under the 4th urgent project of MAFF. In order to develop the control software of the M-3 robot more efficiently, we innovated the RT-middleware “OpenRTM-aist” software platform. In this system, we developed 9 kind of RT-Components (RTC): Robot task sequence player RTC, Proxy RTC for image processing software, DC motor controller RTC, Arm kinematics RTC, and so on. In this paper, we discuss advantages of RT-middleware developing system and problems about operating the RTC-configured robotic system by end-users.

  20. Quantum Spectral Symmetries

    Science.gov (United States)

    Hamhalter, Jan; Turilova, Ekaterina

    2017-02-01

    Quantum symmetries of spectral lattices are studied. Basic properties of spectral order on A W ∗-algebras are summarized. Connection between projection and spectral automorphisms is clarified by showing that, under mild conditions, any spectral automorphism is a composition of function calculus and Jordan ∗-automorphism. Complete description of quantum spectral symmetries on Type I and Type II A W ∗-factors are completely described.

  1. 1500 m3立式圆筒形煤仓有限元计算%Finite Element Calculation of 1 500 m3 Vertical Cylindrical Bunker

    Institute of Scientific and Technical Information of China (English)

    汪志福; 陶保林; 孙文红

    2015-01-01

    Large cylindrical bunker is widely used in oil fired steam injection station project.An analysis of stress strength for the design of a 1 500 m3 vertical cylindrical bunker is given.A large general finite element software ANSYS is used to establish a actual size of the finite element nu-merical model,which connected with a coal bunker tank top,tank walls,bearing,cone bottom, consistent with steel support columns,using powerful border simulation and all kinds of applied load function,in a state filled with water + wind + snow + load cases,to calculate and check the various structural parts of coal bunker.The calculated results show that it has sufficient safe-ty margin and reliability.%大型圆筒式煤仓在油田燃煤注汽站工程中应用广泛,对某1500 m3立式圆筒形煤仓进行了应力强度分析。运用有限元软件 ANSYS 建立了与煤仓罐顶、罐壁、支座连接、锥底、支撑钢架以及立柱实际尺寸相一致的有限元数值计算模型,利用软件的边界模拟和各种荷载施加功能,针对煤仓各结构部分,在充水状态+风载荷+雪载荷+地震载荷工况下进行了应力计算和校核,结果表明,此煤仓具有足够的安全裕度及可靠性。

  2. Wide-Range Enhancement of Spectral Response by Highly Conductive and Transparent μc-SiOx:H Doped Layers in μc-Si:H and a-Si:H/μc-Si:H Thin-Film Solar Cells

    Directory of Open Access Journals (Sweden)

    Pei-Ling Chen

    2016-01-01

    Full Text Available The enhancement of optical absorption of silicon thin-film solar cells by the p- and n-type μc-SiOx:H as doped and functional layers was presented. The effects of deposition conditions and oxygen content on optical, electrical, and structural properties of μc-SiOx:H films were also discussed. Regarding the doped μc-SiOx:H films, the wide optical band gap (E04 of 2.33 eV while maintaining a high conductivity of 0.2 S/cm could be obtained with oxygen incorporation of 20 at.%. Compared to the conventional μc-Si:H(p as window layer in μc-Si:H single-junction solar cells, the application of μc-SiOx:H(p increased the VOC and led to a significant enhancement in the short-wavelength spectral response. Meanwhile, the employment of μc-SiOx:H(n instead of conventional ITO as back reflecting layer (BRL enhanced the external quantum efficiency (EQE of μc-Si:H single-junction cell in the long-wavelength region, leading to a relative efficiency gain of 10%. Compared to the reference cell, the optimized a-Si:H/μc-Si:H tandem cell by applying p- and n-type μc-SiOx:H films achieved a VOC of 1.37 V, JSC of 10.55 mA/cm2, FF of 73.67%, and efficiency of 10.51%, which was a relative enhancement of 16%.

  3. HST UV Observations of the Cores of M3 and M13

    CERN Document Server

    Ferraro, F R; Pecci, F F; Cacciari, C; Dorman, B; Rood, R T; Ferraro, Francesco R.; Paltrinieri, Barbara; Pecci, Flavio Fusi; Cacciari, Carla; Dorman, Ben; Rood, Robert T.

    1997-01-01

    We present preliminary results from HST/WFPC2 observations of the central regions of the of the Galactic globular clusters M13 and M3. The clusters are almost identical in most respects including chemical composition, but there are dramatic differences in both the horizontal branch (HB) and blue straggler (BSS) populations. The M13 HB has a long blue tail extending 4.5 mag in V, reaching well below the level of the main sequence turn-off. M3 has no such feature. M3 and M13 are thus an extreme case of the ``second parameter problem'' in HB morphology. Also present in the M13 HB are two gaps similar to those seen in the clusters NGC 6752 and NGC 2808. M3 has a specific frequency of BSS three times larger than that of M13. Our results imply that neither age nor cluster density, two popular second parameter candidates, are likely to be responsible for the observed differences.

  4. Experimental Conditions: SE37_S16_M3_D1 [Metabolonote[Archive

    Lifescience Database Archive (English)

    Full Text Available opes SE37_S16 Blank (80% methanol) SE37_S16_M3 0mg [MassBase ID] MDLC1_43486 SE37_MS1 Metabolites extraction... with 80% methanol and analysis by LC-Orbitrap-MS SE37_DS1 Peak extraction for unlabeled data ...

  5. The Spectral Shift Function and Spectral Flow

    Science.gov (United States)

    Azamov, N. A.; Carey, A. L.; Sukochev, F. A.

    2007-11-01

    At the 1974 International Congress, I. M. Singer proposed that eta invariants and hence spectral flow should be thought of as the integral of a one form. In the intervening years this idea has lead to many interesting developments in the study of both eta invariants and spectral flow. Using ideas of [24] Singer’s proposal was brought to an advanced level in [16] where a very general formula for spectral flow as the integral of a one form was produced in the framework of noncommutative geometry. This formula can be used for computing spectral flow in a general semifinite von Neumann algebra as described and reviewed in [5]. In the present paper we take the analytic approach to spectral flow much further by giving a large family of formulae for spectral flow between a pair of unbounded self-adjoint operators D and D + V with D having compact resolvent belonging to a general semifinite von Neumann algebra {mathcal{N}} and the perturbation V in {mathcal{N}} . In noncommutative geometry terms we remove summability hypotheses. This level of generality is made possible by introducing a new idea from [3]. There it was observed that M. G. Krein’s spectral shift function (in certain restricted cases with V trace class) computes spectral flow. The present paper extends Krein’s theory to the setting of semifinite spectral triples where D has compact resolvent belonging to {mathcal{N}} and V is any bounded self-adjoint operator in {mathcal{N}} . We give a definition of the spectral shift function under these hypotheses and show that it computes spectral flow. This is made possible by the understanding discovered in the present paper of the interplay between spectral shift function theory and the analytic theory of spectral flow. It is this interplay that enables us to take Singer’s idea much further to create a large class of one forms whose integrals calculate spectral flow. These advances depend critically on a new approach to the calculus of functions of non

  6. On the Family of Thue Equation |x3 + mx2y- (m + 3) xy2 + y3 |= k

    Institute of Scientific and Technical Information of China (English)

    XIA Jingbo; CHEN Jianhua; ZHANG Silan

    2006-01-01

    The family of cubic Thue equation which depend on two parameters | x3 + mx2 y- (m+3) xy2 + y3|=k is studied. Using rational approximation, we give a smaller upper bound of the solution of the equation, that is quite better than the present result. Moreover, we study two inequalities |x3 +mx2y- (m+3)xy2 +y3|=k≤2m+3 and |m3 +mm2y- (m+3)my2 + y3 | = k≤(2m+ 3)2 separately. Our result of upper bound make it easy to solve those inequalities by simple method of continuous fraction expansion.

  7. Divergent evolution of the M3A family of metallopeptidases in plants.

    Science.gov (United States)

    Kmiec, Beata; Teixeira, Pedro F; Murcha, Monika W; Glaser, Elzbieta

    2016-07-01

    Plants, as stationary organisms, have developed mechanisms allowing them efficient resource reallocation and a response to changing environmental conditions. One of these mechanisms is proteome remodeling via a broad peptidase network present in various cellular compartments including mitochondria and chloroplasts. The genome of the model plant Arabidopsis thaliana encodes as many as 616 putative peptidase-coding genes organized in 55 peptidase families. In this study, we describe the M3A family of peptidases, which comprises four members: mitochondrial and chloroplastic oligopeptidase (OOP), cytosolic oligopeptidase (CyOP), mitochondrial octapeptidyl aminopeptidase 1 (Oct1) and plant-specific protein of M3 family (PSPM3) of unknown function. We have analyzed the evolutionary conservation of M3A peptidases across plant species and the functional specialization of the three distinct subfamilies. We found that the subfamily-containing OOP and CyOP-like peptidases, responsible for oligopeptide degradation in the endosymbiotic organelles (OOP) or in the cytosol (CyOP), are highly conserved in all kingdoms of life. The Oct1-like peptidase subfamily involved in pre-protein maturation in mitochondria is conserved in all eukaryotes, whereas the PSPM3-like protein subfamily is strictly conserved in higher plants only and is of unknown function. Specific characteristics within PSPM3 sequences, i.e. occurrence of a N-terminal transmembrane domain and amino acid changes in distal substrate-binding motif, distinguish PSPM3 proteins from other members of M3A family. We performed peptidase activity measurements to analyze the role of substrate-binding residues in the different Arabidopsis M3A paralogs. © 2016 Scandinavian Plant Physiology Society.

  8. XSL : The X-Shooter Spectral Library

    NARCIS (Netherlands)

    Chen, Yanping; Trager, Scott; Peletier, Reynier; Lançon, Ariane

    2011-01-01

    We are building a new spectral library with the X-Shooter instrument on ESO's VLT: XSL, the X-Shooter Spectral Library. We present our progress in building XSL, which covers the wavelength range from the near-UV to the near-IR with a resolution of R~10 000. At the time of writing we have collected s

  9. XSL: The X-Shooter Spectral Library

    NARCIS (Netherlands)

    Chen, Yanping; Trager, Scott; Peletier, Reynier; Lançon, Ariane

    2011-01-01

    We are building a new spectral library with the X-Shooter instrument on ESO's VLT: XSL, the X-Shooter Spectral Library. We present our progress in building XSL, which covers the wavelength range from the near-UV to the near-IR with a resolution of R~10 000. At the time of writing we have collected s

  10. XSL : The X-Shooter Spectral Library

    NARCIS (Netherlands)

    Chen, Yanping; Trager, Scott; Peletier, Reynier; Lan¸con, Ariane

    2011-01-01

    We are building a new spectral library with the X-Shooter instrument on ESO’s VLT: XSL, the X-Shooter Spectral Library. We present our progress in building XSL, which covers the wavelength range from the near-UV to the near-IR with a resolution of R 10000. At the time of writing we have collected sp

  11. Autoregressive Spectral Estimation and Functional Inference.

    Science.gov (United States)

    1982-06-01

    spectral density function . Note that F(O) - 0, F(l) = 1, and (15) F(w) = f(w’) dw’, O<w<l...correlation function p(v) is summable, and its spectral density function f(w) is bounded above and below in the sense that the dynamic range of f(w) (2) DR...l The AR(-n) and MA(-) representations have important implications for spectral 6 analysis since they provide formulas for the spectral density function

  12. Optical Spectral Variability of Blazars

    Indian Academy of Sciences (India)

    Haritma Gaur

    2014-09-01

    It is well established that blazars show flux variations in the complete electromagnetic (EM) spectrum on all possible time scales ranging from a few tens of minutes to several years. Here, we report the review of optical flux and spectral variability properties of different classes of blazars on IDV and STV time-scales. Our analysis show HSPs are less variable in optical bands as compared to LSPs. Also, we investigated the spectral slope variability and found that the average spectral slopes of LSPs showed a good agreement with the synchrotron self-Compton loss-dominated model. However, spectra of the HSPs and FSRQs have significant additional emission components. In general, spectra of BL Lacs get flatter when they become brighter, while for FSRQs the opposite trend appears to hold.

  13. 藏红T在核酸分子表面进行长距组装的光谱特征%Spectral characteristics of the long range assembly of safranine T on the molecular surfaces of nucleic acids

    Institute of Scientific and Technical Information of China (English)

    黄承志; 黄新华; 李原芳

    2000-01-01

    The long-range assembly of Safranine T(ST) on the molecular surfaces of nucleic acids is characterized by measuring resonance light scattering (RLS), electronic absorption and fluorescence emission. It was found that the long range assembly of ST on the molecular surfaces of nucleic acids at pH 7.05 and ionic strength 0.004 5, depending on the molar ratio of ST to nucleic acids, involves two processes. When the molar ratio of ST to nucleic acids is larger than 1.33, the long range assembly of ST on the molecular surface of nucleic acids occurs, which characterizes hypsochromicly hypochromic effect, fluorescence quenching, and three strong enhanced peaks of resonance light-scattering at 328.0, 472.0 and 572.0 nm. When the molar ratio is lower than 1.33, however, the disassociation of the species of the long range assembly of ST takes places, which characterizes bathochromically hypochromic effect, fluorescence quenching, and weak enhanced resonance light-scattering. Intercalative binding of ST in to DNA takes place in the process of the disassociation of the assembly species.%表征了藏红T(ST)在核酸分子表面进行长距组装的共振光散射光谱、电子吸收和发射特征. 结果表明, pH 7.05、离子强度0.004 5下ST在核酸表面进行的长距组装随着ST与核酸的摩尔比(R)不同涉及到两种作用机理, 当R>1.3时, 长距组装表现为紫移的减色效应和荧光猝灭, 在328.0 nm、472.0 nm和572.0 nm; R<1.33时, 长距组装产物发生离解, 具有红移的减色效应、荧光猝灭和微弱的共振光散射增强, 并有部分ST嵌入到DNA碱基对之间.

  14. Spectral Classification Beyond M

    CERN Document Server

    Leggett, S K; Burgasser, A J; Jones, H R A; Marley, M S; Tsuji, T

    2004-01-01

    Significant populations of field L and T dwarfs are now known, and we anticipate the discovery of even cooler dwarfs by Spitzer and ground-based infrared surveys. However, as the number of known L and T dwarfs increases so does the range in their observational properties, and difficulties have arisen in interpreting the observations. Although modellers have made significant advances, the complexity of the very low temperature, high pressure, photospheres means that problems remain such as the treatment of grain condensation as well as incomplete and non-equilibrium molecular chemistry. Also, there are several parameters which control the observed spectral energy distribution - effective temperature, grain sedimentation efficiency, metallicity and gravity - and their effects are not well understood. In this paper, based on a splinter session, we discuss classification schemes for L and T dwarfs, their dependency on wavelength, and the effects of the parameters T_eff, f_sed, [m/H] and log g on optical and infra...

  15. Resolution-enhancing hybrid, spectral CT reconstruction

    Science.gov (United States)

    Clark, D. P.; Badea, C. T.

    2016-04-01

    Spectral x-ray imaging based on photon-counting x-ray detectors (PCXD) is an area of growing interest. By measuring the energy of x-ray photons, a spectral CT system can better differentiate elements using a single scan. However, the spatial resolution achievable with most PCXDs limits their application, particularly in preclinical CT imaging. Consequently, our group is developing a hybrid micro-CT scanner based on a high-resolution, energy-integrating (EID) detector and a lower-resolution, PCXD. To complement this system, we propose and demonstrate a hybrid, spectral CT reconstruction algorithm which robustly combines the spectral contrast of the PCXD with the spatial resolution of the EID. Specifically, the high-resolution, spectrally resolved data (X) is recovered as the sum of two matrices: one with low column rank (XL) determined from the EID data and one with intensity gradient sparse columns (XS) corresponding to the upsampled spectral contrast obtained from the PCXD data. We test the proposed algorithm in a feasibility study focused on molecular imaging of atherosclerotic plaque using activatable iodine and gold nanoparticles. The results show accurate estimation of material concentrations at increased spatial resolution for a voxel size ratio between the PCXD and the EID of 500 μm3:100 μm3. Specifically, regularized, iterative reconstruction of the MOBY mouse phantom around the K-edges of iodine (33.2 keV) and gold (80.7 keV) reduces the reconstruction error by more than a factor of three relative to least-squares, algebraic reconstruction. Likewise, the material decomposition accuracy into iodine, gold, calcium, and water improves by more than a factor of two.

  16. Residual stress in a M3:2 PM high speed steel; effect of mechanical loading

    DEFF Research Database (Denmark)

    Højerslev, Christian; Odén, Magnus; Carstensen, Jesper V.

    2001-01-01

    X-ray lattice strains were investigated in an AISI M3:2 PM high-speed steel in the as heat treated condition and after exposure to alternating mechanical load. The volume changes during heat treatment were monitored with dilatometry. Hardened and tempered AISI M3:2 steel consists of tempered lath...... martensite and the carbides M6C,V8C7 and M23C6. In the as heat treated condition the stress state is triaxial. The primary carbides M6C and V8C7 experience a compressive state of stress. Exposure to an alternating mechanical load, changes the states of stress of V8C7 and tempered martensite, but does...... not appear to change the state of stress in M6C....

  17. The Abundance of Lithium in an AGB Star in the Globular Cluster M3 (NGC 5272)

    CERN Document Server

    Givens, R A

    2016-01-01

    A survey of red giants in the globular cluster M3 with the Hydra multi-object spectrograph on the WIYN 3.5-m telescope indicated a prominent Li I 6707 $\\AA$ feature in the red giant vZ 1050. Follow-up spectroscopy with the ARC 3.5-m telescope confirmed this observation and yielded a derived abundance of A(Li)$_{NLTE}$ = 1.6 $\\pm$ 0.05. In addition, the high oxygen and low sodium abundances measured from the same spectrum suggest that vZ 1050 is a first generation cluster star. The location vZ 1050 above the horizontal branch and blueward of the red giant branch in the cluster's color-magnitude diagram places vZ 1050 on M3's asymptotic giant branch. The likely source for the enhanced lithium abundance is the Cameron-Fowler mechanism operating in vZ 1050 itself.

  18. The Abundance of Lithium in an ABG Star in the Globular Cluster M3 (NGC 5272)

    Science.gov (United States)

    Givens, R. A.; Pilachowski, C. A.

    2016-12-01

    A survey of red giants in the globular cluster M3 with the Hydra multi-object spectrograph on the WIYN 3.5 m telescope indicated a prominent Li i 6707 Å feature in the red giant vZ 1050. Followup spectroscopy with the ARC 3.5 m telescope confirmed this observation and yielded a derived abundance of A(Li)NLTE = 1.6 ± 0.05. In addition, the high oxygen and low sodium abundances measured from the same spectrum suggest that vZ 1050 is a first generation cluster star. The location of vZ 1050 above the horizontal branch and blueward of the red giant branch in the cluster’s color-magnitude diagram places vZ 1050 on M3's asymptotic giant branch. The likely source for the enhanced lithium abundance is the Cameron-Fowler mechanism operating in vZ 1050 itself.

  19. M3A system (2000–2005 – operation and maintenance

    Directory of Open Access Journals (Sweden)

    G. Petihakis

    2006-05-01

    Full Text Available During the Pilot Phase of the Mediterranean Forecasting System (MFSPP (1998–2001 a prototype observing system (Mediterranean Moored Multi-sensor Array – M3A was designed, developed and operated in the Cretan Sea for continuous oceanographic measurements in real time. The main problems encountered were associated with biofouling, underwater and aerial communication and with the design of the surface buoy. In the second phase of the MFS project named Mediterranean Forecasting System Towards Environmental Predictions (MFSTEP (2001–2005, the aim was to solve those problems and to consolidate the M3A. During the approximately five years of operation there were 13 scheduled and 15 emergency visits with a total duration of 65 days. The acquired experience through the maintenance program proved that the continuous observation of a so important system with a relative low cost is feasible.

  20. M3MS-16OR0401086 – Report on NEAMS Workbench Support for MOOSE Applications

    Energy Technology Data Exchange (ETDEWEB)

    Lefebvre, Robert A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Reactor and Nuclear Systems Division; Langley, Brandon R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Reactor and Nuclear Systems Division; Thompson, Adam B. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Reactor and Nuclear Systems Division

    2016-09-23

    This report summarizes the status of the Nuclear Energy Advanced Modeling and Simulation (NEAMS) Workbench from Oak Ridge National Laboratory (ORNL) and the integration of the MOOSE framework. This report marks the completion of NEAMS milestone M3MS-16OR0401086. This report documents the developed infrastructure to support the MOOSE framework applications, the applications’ results, visualization status, the collaboration that facilitated this progress, and future considerations.

  1. New species of Triplocania Roesler with forewing M3 forked (Psocodea: 'Psocoptera': Ptiloneuridae), from Brazil.

    Science.gov (United States)

    Da Silva Neto, Alberto Moreira; Rafael, José Albertino; Aldrete, Alfonso N García

    2014-07-16

    Four new Brazilian species of Triplocania with forewing M3 forked are described and illustrated based on male specimens, namely: Triplocania lamasi n.sp. (Mato Grosso: Brazil), Triplocania mariateresae n.sp. (Rio de Janeiro: Brazil), Triplocania newi n.sp. (Tocantins: Brazil) and Triplocania plaumanni n.sp. (Santa Catarina: Brasil). They differ from all the other species in the genus, in which the males are known, by the hypandrium and phallosome structures.

  2. A novel antiarrhythmic target-M3-R/IKM3

    Institute of Scientific and Technical Information of China (English)

    Bao-fengYANG

    2004-01-01

    The total efficient rate of antiarrhythmic agents is only 30%to 60%, and the compounding problem is the lack of an effective therapy for some serious arrhythmias. Muscarinic receptors have been cloned and subdivided into the five subtypes M1, M2, M3,M4 and M5. And M2 receptors have long been believed to be the only functional subtype of muscarinic acetylcholine receptor (mAChR) in the heart, although recent studies have provided

  3. A picrotoxin-specific conformational change in the glycine receptor M2-M3 loop.

    Science.gov (United States)

    Hawthorne, Rebecca; Lynch, Joseph W

    2005-10-28

    The external loop linking the M2 and M3 transmembrane domains is crucial for coupling agonist binding to channel gating in the glycine receptor chloride channel (GlyR). A substituted cysteine accessibility scan previously showed that glycine activation increased the surface accessibility of 6 contiguous residues (Arg271-Lys276) toward the N-terminal end of the homomeric alpha1 GlyR M2-M3 loop. In the present study we used a similar approach to determine whether the allosteric antagonist, picrotoxin, could impose conformational changes to this domain that cannot be induced by varying agonist concentrations alone. Picrotoxin slowed the reaction rate of a sulfhydryl-containing compound (MTSET) with A272C, S273C, and L274C. Before interpreting this as a picrotoxin-specific conformational change, it was necessary to eliminate the possibility of steric competition between picrotoxin and MTSET. Accordingly, we showed that picrotoxin and the structurally unrelated blocker, bilobalide, were both trapped in the R271C GlyR in the closed state and that a point mutation to the pore-lining Thr6' residue abolished inhibition by both compounds. We also demonstrated that the picrotoxin dissociation rate was linearly related to the channel open probability. These observations constitute a strong case for picrotoxin binding in the pore. We thus conclude that the picrotoxin-specific effects on the M2-M3 loop are mediated allosterically. This suggests that the M2-M3 loop responds differently to the occupation of different binding sites.

  4. Study of the continuum removal method for the Moon Mineralogy Mapper (M3) and its application to Mare Humorum and Mare Nubium

    Science.gov (United States)

    Zhang, Xun-Yu; Ouyang, Zi-Yuan; Zhang, Xiao-Meng; Chen, Yuan; Tang, Xiao; Xu, Ao-Ao; Tang, Ze-Sheng; Wu, Yun-Zhao

    2016-07-01

    The absorption band center of visible and near infrared reflectance spectra is a key spectral parameter for lunar mineralogical studies, especially for the mafic minerals (olivine and pyroxene) of mare basalts, which have two obvious absorption bands at 1000 nm (Band I) and 2000nm (Band II). Removal of the continuum from spectra, which was developed by Clark and Roush and used to isolate the particular absorption feature, is necessary to estimate this parameter. The Moon Mineralogy Mapper (M3) data are widely used for lunar mineral identification. However, M3 data show a residual thermal effect, which interferes with the continuum removal, and systematic differences exist among optical data taken during different optical periods. This study investigated a suitable continuum removal method and compared the difference between two sets of M3 data taken during different optical periods, Optical Period 1B (OP1B) and Optical Period 2A (OP2A). Two programs for continuum removal are reported in this paper. Generally, a program respectively constructs two straight lines across Band I and Band II to remove the continuum, which is recommended for locating band centers, because it can find the same Band I center with different right endpoints. The optimal right endpoint for continuum removal is mainly dominated by two optical period data at approximately 2480 and 2560nm for OP1B and OP2A data, respectively. The band center values derived from OP1B data are smaller than those derived from OP2A data in Band I but larger in Band II, especially for the spectra using longer right endpoints (>2600 nm). This may be due to the spectral slopes of OP1B data being steeper than those of OP2A data in Band I but gentler in Band II. These results were applied to Mare Humorum and Mare Nubium, and the measurements were found to mainly vary from intermediate- to high-Ca pyroxene.

  5. Development, Implementation and Evaluation of an M3 Community Health Curriculum

    Directory of Open Access Journals (Sweden)

    Staci Young, MS

    2004-03-01

    Full Text Available Objectives: This paper describes the development, implementation and evaluation of an M3 community health curriculum that responds to recent changes within the health care finance and delivery system. Methods: The new curriculum was developed based on AAMC recommendations, LCME requirements, a national review of undergraduate community health curricula, and an internal review of the integration of community health concepts in M3 clerkships. Results: The M3 curriculum teaches: 1 the importance of being a community responsive physician; 2 SES factors that influence health; 3 cultural competency; and 4 the role of physicians as health educators. Student evaluations for the first twelve months of implementation indicate that students are most satisfied with presentations and less satisfied with required readings and a patient interview project. Discussion: Most students agree that at the completion of the course they understand what it means to be a community-responsive physician, and they have developed skills to help them become more community responsive. Evaluation tools need to be developed to assess if students’ behavior has changed due to course participation.

  6. Performance of 500 m3 TankCell® at Kevitsa Cu-Ni-PGM concentrator

    Directory of Open Access Journals (Sweden)

    Mattsson Toni

    2016-01-01

    Full Text Available Outotec TankCell e500 flotation cell, with 500 m3 of efficient flotation volume, has been in operation since October 2014 at Kevitsa Cu-Ni-PGM concentrator as the first Cu rougher flotation cell. The 500 m3 flotation cell has proven to provide metallurgical superiority at very low specific power. On average the cell has recovered 71% of copper contained in the flotation feed. The cell has produced the concentrate with the Cu grade equal to 17% Cu. The typical specific power for the cell is around 0.4 kW/m3 (blower power not included. After the start-up of the cell the operating parameters have varied. The mixing speed have varied from 4.9 to 7.0 m/s and the superficial gas velocity from 0.3 to 1.5 cm/s. At various operating parameters the mixing, gas dispersion and metallurgical performance of the cell have been evaluated. In this paper a review of the hydrodynamic and metallurgical performance of the cell is presented. The paper focuses on the interactions of mixing intensity, bubble size and metallurgical performance in industrial application.

  7. Mice Lacking M1 and M3 Muscarinic Acetylcholine Receptors Have Impaired Odor Discrimination and Learning

    Science.gov (United States)

    Chan, Wilson; Singh, Sanmeet; Keshav, Taj; Dewan, Ramita; Eberly, Christian; Maurer, Robert; Nunez-Parra, Alexia; Araneda, Ricardo C.

    2017-01-01

    The cholinergic system has extensive projections to the olfactory bulb (OB) where it produces a state-dependent regulation of sensory gating. Previous work has shown a prominent role of muscarinic acetylcholine (ACh) receptors (mAChRs) in regulating the excitability of OB neurons, in particular the M1 receptor. Here, we examined the contribution of M1 and M3 mAChR subtypes to olfactory processing using mice with a genetic deletion of these receptors, the M1−/− and the M1/M3−/− knockout (KO) mice. Genetic ablation of the M1 and M3 mAChRs resulted in a significant deficit in odor discrimination of closely related molecules, including stereoisomers. However, the discrimination of dissimilar molecules, social odors (e.g., urine) and novel object recognition was not affected. In addition the KO mice showed impaired learning in an associative odor-learning task, learning to discriminate odors at a slower rate, indicating that both short and long-term memory is disrupted by mAChR dysfunction. Interestingly, the KO mice exhibited decreased olfactory neurogenesis at younger ages, a deficit that was not maintained in older animals. In older animals, the olfactory deficit could be restored by increasing the number of new born neurons integrated into the OB after exposing them to an olfactory enriched environment, suggesting that muscarinic modulation and adult neurogenesis could be two different mechanism used by the olfactory system to improve olfactory processing. PMID:28210219

  8. 微波辅助表面修饰:大范围可控调节CdTe纳米粒子发光光谱%Tunable Photoluminescence of CdTe Nanocrystals over Wide Spectral Range via Microwave-assisted Surface Modification

    Institute of Scientific and Technical Information of China (English)

    刘斌; 李军; 李景虹

    2007-01-01

    An easy and fast microwave-assisted method of tuning the photoluminescence properties of CdTe nanocrystals in aqueous phase is presented. The photoluminescence could be tuned covering almost the whole visual spectral range (537-680 nm), and even partially extending to the near-infrared spectral range. The effect is probably related to the formation of core/shell structure and complex nano-assemblies. These results provide a promising means of tuning the photoluminescence of CdTe nanocrystals, leading to potential applications in biomedical labeling, solar cells, lasers, and other fields.%利用微波辅助合成方法简单快捷地调节水溶液中CdTe纳米晶的发光性质,使其发光光谱可以覆盖整个可见光区,甚至部分扩展到近红外(537~680 nm).这种光谱调控的原因可能是由于CdTe纳米晶表面形成了核壳结构以及纳米粒子之间形成复杂的纳米组合体.

  9. Anomalous Hall hysteresis in T m3F e5O12/Pt with strain-induced perpendicular magnetic anisotropy

    Science.gov (United States)

    Tang, Chi; Sellappan, Pathikumar; Liu, Yawen; Xu, Yadong; Garay, Javier E.; Shi, Jing

    2016-10-01

    We demonstrate robust interface strain-induced perpendicular magnetic anisotropy in atomically flat ferrimagnetic insulator T m3F e5O12 (TIG) films grown with pulsed laser deposition on a substituted G d3G a5O12 substrate which maximizes the tensile strain at the interface. In bilayers consisting of Pt and TIG, we observe large squared Hall hysteresis loops over a wide range of thicknesses of Pt at room temperature. When a thin Cu layer is inserted between Pt and TIG, the Hall hysteresis magnitude decays but stays finite as the thickness of Cu increases up to 5 nm. However, if the Cu layer is placed atop Pt instead, the Hall hysteresis magnitude is consistently larger than when the Cu layer with the same thickness is inserted in between for all Cu thicknesses. These results suggest that both the proximity-induced ferromagnetism and spin current contribute to the anomalous Hall effect.

  10. 基于能量守恒的星间距离变率与地球重力场频谱关系的建立与分析%Establishment and Analysis of the Spectral Relationship Between Range-Rate and Gravity Potential Based on Energy Conservation

    Institute of Scientific and Technical Information of China (English)

    宁津生; 钟波; 罗志才; 罗佳

    2009-01-01

    The spectral relationship between range-rate measurements and the gravity potential for low-low satellite-to-satellite tracking mission was established based on the energy conservation theory. Then the performances of satellite separation, the orbital altitude, and the accuracy of range-rate measurements in recovering the earth's gravity field were simulated and analyzed by this method. Finally, the cumulative geoid errors of the reference mode were obtained by using the configuration parameters of the GRACE mission. By comparing the cumulative geoid errors of the reference mode and GGMO2S and EIGEN-GRACEO2S models, it basically reflected the performance of GRACE and proved the feasibility of this method.

  11. Detection of Mg spinel lithologies on central peak of crater Theophilus using Moon Mineralogy Mapper (M3) data from Chandrayaan-1

    Indian Academy of Sciences (India)

    D Lal; P Chauhan; R D Shah; S Bhattacharya; Ajai; A S Kiran Kumar

    2012-06-01

    Spectral reflectance data derived from Moon Mineralogy Mapper (M3) onboard India’s Chandrayaan-1 has revealed Fe bearing Mg-spinel-rich lithology on central peaks of the crater Theophilus. These newly identified Fe bearing Mg-spinel-rich rock types are defined by their strong 2-m absorption and lack of 1-m absorptions in spectral reflectance response. Such lithology has been reported previously along the inner ring of Moscoviense Basin on the lunar far side. The Modified Gaussian Modeling (MGM) analysis of the Fe bearing Mg-spinel reflectance spectra has been done and the results of the analysis clearly bring out a strong spectral absorption at 1872 nm with no significant absortion around 1000 nm. The presence of spinel group of minerals in the Theophilus central peak and the fact that central peaks mostly represent uplifted mass of deep crustal material confirm that central peaks can be used as a window to study the deep crustal and/or upper mantle composition and may lead to a fresh perspective about the crustal composition of Moon.

  12. Vasco da Gama 33000m3耙吸挖泥船

    Institute of Scientific and Technical Information of China (English)

    刘厚恕; 顾洁

    2001-01-01

    The 33000m3 Vasco da Gama was delivered to the owner in 2000, which is the largest trailing suction hopper dredger up to now. The vessel is designed for the following main functions: loading spoil with two side suction pipes at a depth of 45-60m; transporting the spoil at a speed of 16.Skn; dumping spoil through six pairs of bottom doors; self-discharging of spoil via floating pipeline; self-discharging of spoil through bow-jet nozzle; deep dredging at 131m with 5500kW submerged dredge pump. This paper fully described its arrangement, key dredging equipments and major design features,

  13. Deposition of CdTe films under microgravity: Foton M3 mission

    Energy Technology Data Exchange (ETDEWEB)

    Benz, K.W.; Croell, A. [Freiburger Materialforschungszentrum FMF, Albert-Ludwigs-Universitaet Freiburg (Germany); Zappettini, A.; Calestani, D. [CNR Parma, Instituto Materiali Speciali per Elettronica e Magnetismo IMEM, Fontani Parma (Italy); Dieguez, E. [Universidad Autonoma de Madrid (Spain). Departamento de Fisica de Materiales; Carotenuto, L.; Bassano, E. [Telespazio Napoli, Via Gianturco 31, 80146 Napoli (Italy); Fiederle, M.

    2009-10-15

    Experiments of deposition of CdTe films have been carried out under microgravity in the Russian Foton M3 mission. The influence of gravity has been studied with these experiments and compared to the results of simulations. The measured deposition rate could be confirmed by the theoretical results for lower temperatures. For higher temperatures the measured thickness of the deposited films was larger compared to the theoretical data. (copyright 2009 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  14. Postpartum Diagnosis of AML-M3: A Rare Case Report

    Directory of Open Access Journals (Sweden)

    Manjula Biradar

    2016-07-01

    Full Text Available A 27 year old female gravid 2, para 1, presented at 39 weeks of gestation with pain in abdomen going in for labour, and delivered healthy baby. The patient later had post-partum haemorrhage with Prothrombin Time (PT 10min, platelet count 70,000 cells/cumm. Peripheral smear showed shift to left with myeloblasts, promyelocytes. The diagnosis of Acute Myeloid Leukemia (AML was given and advised for bone marrow examination. The diagnosis AML-M3 was confirmed by marrow study. Unfortunately, patient went in for Disseminated Intravascular Coagulation (DIC and died 2 days after the diagnosis.

  15. Lunar Exploration Insights Recognized from Chandrayaan-1 M3 Imaging Spectrometer

    Science.gov (United States)

    Pieters, Carle; Green, Robert O.; Boardman, Joseph

    2016-07-01

    One of the most important lessons learned from the renaissance of lunar exploration over the last decade is that new discoveries and surprises occur with every new mission to the Moon. Although the color of the Moon had been measured using Earth-based telescopes even before Apollo, modern instruments sent to orbit the Moon provide a scope of inquiry unimaginable during the last century. Spacecraft have now been successfully sent to the Moon by six different space agencies from around the world and the number is growing. The Indian Chandrayaan- 1 spacecraft carried a suite of indigenous instruments as well as several guest instruments from other countries, including the Moon Mineralogy Mapper (M-cube) supplied by NASA. Even though Chandrayaan's lifetime in orbit was shortened by technical constraints, M3 provided a taste of the power of near-infrared imaging spectroscopy used for science and exploration at the Moon. Contrary to expectations, the lunar surface was discovered to be hydrated, which is now known to result from solar wind H combining with O of rocks and soil. Surficial hydration was found to be pervasive across the Moon and the limited data hint at both local concentrations and temporal variations. The prime objective of M3 was to characterize lunar mineralogy in a spatial context. Working in tandem with related instruments on JAXA's SELENE, M3 readily recognized and mapped known minerals from mare and highland terrains (pyroxenes, olivine) at high resolution, but also detected diagnostic properties of crystalline plagioclase which, when mapped across a spatial context, enabled the unambiguous identification of a massive crustal layer of plagioclase that clearly resulted from an early magma ocean. An additional surprise came with the discovery of a new rock type on the Moon that had not been recognized in samples returned by Apollo and Luna: a Mg-rich spinel anorthosite associated with material excavated from some of the greatest lunar depths. In

  16. Forsmark Site: M3 modelling and 2D visualisation of the hydrochemical parameters in Forsmark groundwater

    Energy Technology Data Exchange (ETDEWEB)

    Gurban, Ioana (3D Terra (Canada))

    2008-08-15

    This work represents the stage 2.3 of the hydrochemical evaluation and modelling of the Forsmark data. This comprises M3 modelling and 2D visualisation of the data along the boreholes. The following conclusions can be drawn: - M3 modelling helped to summarise and understand the data, by using as variables the major elements and the isotopes delta18O and deltaD. - Previous alternative models and the experience from Forsmark 1.2, 2.1 and 2.2, helped to clarify different previously unsolved issues such as: the use of variables, tests with different endmembers, the use of only groundwater data in order to build a bedrock hydrochemical model. - The visualisation of the mixing proportions along the boreholes helps to understand the distribution of the data in the domain and to check and compare the results of different models; and therefore to chose the model which best describes the measured data. - The different M3 modelling tests resulted in the following conclusions: a) When calculating mixing proportions only samples from the boreholes will be used, b) the altered meteoric end-member which best describes the more shallow groundwater compositions is defined by a representative upper bedrock sample; the Littorina end-member employed the existing modelled compositions; the Deep saline and glacial end-members compositions were tested by means of a feasibility study and employed in the modelling. - Three models were presented. All the models are good and can be used, but the best is to use the one that fits the conceptual model best and the hydrogeochemical understanding. - The use of Littorina, Glacial, Deep Saline and Altered Meteoric end-members makes possible the comparison of different sites such as Laxemar and Forsmark. - All the data used in the M3 modelling and the results of the modelling and visualisation along the boreholes are presented in SKB database SIMON. - The extended data do not affect the results of the modelling of the Forsmark 2.3 dataset (the

  17. Spectral analysis by correlation; Analyse spectrale par correlation

    Energy Technology Data Exchange (ETDEWEB)

    Fauque, J.M.; Berthier, D.; Max, J.; Bonnet, G. [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1969-07-01

    The spectral density of a signal, which represents its power distribution along the frequency axis, is a function which is of great importance, finding many uses in all fields concerned with the processing of the signal (process identification, vibrational analysis, etc...). Amongst all the possible methods for calculating this function, the correlation method (correlation function calculation + Fourier transformation) is the most promising, mainly because of its simplicity and of the results it yields. The study carried out here will lead to the construction of an apparatus which, coupled with a correlator, will constitute a set of equipment for spectral analysis in real time covering the frequency range 0 to 5 MHz. (author) [French] La densite spectrale d'un signal qui represente la repartition de sa puissance sur l'axe des frequences est une fonction de premiere importance, constamment utilisee dans tout ce qui touche le traitement du signal (identification de processus, analyse de vibrations, etc...). Parmi toutes les methodes possibles de calcul de cette fonction, la methode par correlation (calcul de la fonction de correlation + transformation de Fourier) est tres seduisante par sa simplicite et ses performances. L'etude qui est faite ici va deboucher sur la realisation d'un appareil qui, couple a un correlateur, constituera un ensemble d'analyse spectrale en temps reel couvrant la gamme de frequence 0 a 5 MHz. (auteur)

  18. The Mediterranean Moored Multi-sensor Array (M3A: system development and initial results

    Directory of Open Access Journals (Sweden)

    K. Nittis

    Full Text Available Operational forecasting of ocean circulation and marine ecosystem fluctuations requires multi-parametric real-time measurements of physical and biochemical properties. The architecture of a system that is able to provide such measurements from the upper-thermocline layers of the Mediterranean Sea is described here. The system was developed for the needs of the Mediterranean Forecasting System and incorporates state-of-the-art sensors for optical and chemical measurements in the upper 100 m and physical measurements down to 500 m. Independent moorings that communicate via hydro-acoustic modems are hosting the sensors. The satellite data transfer and the large autonomy allow for the operation of the system in any open-ocean site. The system has been in pre-operational use in the Cretan Sea since January 2000. The results of this pilot phase indicate that multi-parametric real-time observations with the M3A system are feasible, if a consistent maintenance and re-calibration program is followed. The main limitations of the present configuration of M3A are related: (a to bio-fouling that primarily affects the turbidity and secondarily affects the other optical sensors, and (b to the limited throughput of the currently used satellite communication system.

    Key words. Atmospheric composition and structure (instruments and techniques. Oceanography: general (ocean prediction Oceanography: physical (upper ocean process

  19. Connexins and M3 Muscarinic Receptors Contribute to Heterogeneous Ca2+ Signaling in Mouse Aortic Endothelium

    Directory of Open Access Journals (Sweden)

    François-Xavier Boittin

    2013-02-01

    Full Text Available Background/Aims: Smooth muscle tone is controlled by Ca2+ signaling in the endothelial layer. Mouse endothelial cells are interconnected by gap junctions made of Connexin40 (Cx40 and Cx37, which allow the exchange of signaling molecules to coordinate their activity. Here, we investigated the role of Cx40 in the endothelial Ca2+ signaling of the mouse aorta. Methods: Ca2+ imaging was performed on intact aortic endothelium from both wild type (Cx40+/+ and Connexin40-deficient (Cx40 -/- mice. Results: Acetylcholine (ACh induced early fast and high amplitude Ca2+ transients in a fraction of endothelial cells expressing the M3 muscarinic receptors. Inhibition of intercellular communication using carbenoxolone or octanol fully blocked the propagation of ACh-induced Ca2+ transients toward adjacent cells in WT and Cx40-/- mice. As compared to WT, Cx40-/- mice displayed a reduced propagation of ACh-induced Ca2+ waves, indicating that Cx40 contributes to the spreading of Ca2+ signals. The propagation of those Ca2+ responses was not blocked by suramin, a blocker of purinergic ATP receptors, indicating that there is no paracrine effect of ATP release on the Ca2+ waves. Conclusions: Altogether our data show that Cx40 and Cx37 contribute to the propagation and amplification of the Ca2+ signaling triggered by ACh in endothelial cells expressing the M3 muscarinic receptors.

  20. HST Observations of Blue Straggler Stars in the Core of the Globular Cluster M3

    CERN Document Server

    Ferraro, F R; Pecci, F F; Cacciari, C; Dorman, B; Rood, R T; Buonanno, R; Corsi, C E; Burgarella, D; Laget, M

    1997-01-01

    The core of the Galactic Globular Cluster M3 (NGC 5272) has been observed with the WFPC2 through the filters F255W, F336W, F555W, and F814W. Using these observations along with a thorough reanalysis of earlier catalogs, we have produced a catalog of blue straggler stars (BSS) spanning the cluster. Earlier studies and the fainter part of our sample suffer severe selection biases. Our analysis is based on a more reliable bright global sample of 122 BSS. We confirm earlier suggestions that the radial BSS distribution in M3 is bimodal. It is strongly peaked in the center, has a clear dip 100--200" from the center, and rises again at larger radii. The observed distribution agrees with the dynamical model of Sigurdsson et al. (1994) which takes into account both star collisions and merging of primordial binaries for the origin of BSS. The observed luminosity functions of BSS in the inner and outer parts of the cluster are different. Interpreting these using the models of Bailyn & Pinsonneault (1995), we suggest...

  1. Scale-up of industrial biodiesel production to 40 m3using a liquid lipase formulation

    DEFF Research Database (Denmark)

    Price, Jason; Nordblad, Mathias; Martel, Hannah H.

    2016-01-01

    In this work, we demonstrate the scale-up from an 80 L fed-batch scale to 40 m3 along with the design of a 4 m3continuous process for enzymatic biodiesel production catalysed by NS-40116 (a liquid formulation of a modified Thermomyces lanuginosus lipase). Based on the analysis of actual pilot plant...... the fed-batch and CSTR cases. Given similar operating conditions, the CSTR operation on average, has a reaction time which is 1.3 times greater than the fed-batch operation. We also showed how the process metrics can be used to quickly estimate the selling price of the enzyme. Assuming a biodiesel selling...... price of 0.6 USD/kg and a one-time use of the enzyme (0.1% (w/woil) enzyme dosage); the enzyme can then be sold for 30 USD/kg which ensures that that the enzyme cost is not more than 5% of the biodiesel revenue. This article is protected by copyright. All rights reserved...

  2. M3A system (2000–2005 – operation and maintenance

    Directory of Open Access Journals (Sweden)

    G. Petihakis

    2007-01-01

    Full Text Available During the pilot phase of the Mediterranean Forecasting System (MFSPP (2000 2003, a prototype observing system (Mediterranean Moored Multi-sensor Array – M3A was designed, developed and operated in the Cretan Sea for continuous oceanographic measurements in real time. The main problems encountered were associated with biofouling, underwater and aerial communication and with the design of the surface buoy. In the second phase of the MFS project named Mediterranean Forecasting System Towards Environmental Predictions (MFSTEP (2003–2005, the aim was to solve those problems and to consolidate the M3A. For the minimisation of biofouling a pilot field study was performed and the techniques of bromine solution and copper shielding were evaluated. Additionally, the oligotrophy of the Aegean Sea dictated the need to ignore factory calibrations and to perform site-specific laboratory calibrations of the sensors. This procedure was proved necessary and produced calibration coefficients that gave results comparable to the measurements obtained with the laboratory analysis method. During the approximately five years of operation, there were 13 scheduled and 15 emergency visits, with a total duration of 65 days. The acquired experience through the maintenance program proved that the continuous observation of such a very important system with a relative low cost is feasible.

  3. Machining risk of beryllium disease and sensitization with median exposures below 2 micrograms/m3.

    Science.gov (United States)

    Kreiss, K; Mroz, M M; Newman, L S; Martyny, J; Zhen, B

    1996-07-01

    We examined the prevalence of beryllium sensitization in relation to work process and beryllium exposure measurements in a beryllia ceramics plant that had operated since 1980. We interviewed 136 employees (97.8% of the workforce), ascertained beryllium sensitization with the beryllium lymphocyte proliferation blood test, and reviewed historical industrial hygiene measurements. Of eight beryllium-sensitized employees (5.9%), six (4.4% of participating employees) had granulomatous disease on transbronchial lung biopsy. Machinists had a sensitization rate of 14.3% compared to a rate of 1.2% among other employees. Machining had significantly higher general area and breathing zone measurements than did other processes in the time period in which most beryllium-sensitized cases had started machining work. Daily weighted average (DWA) estimates of exposure for matching processes also exceeded estimates for other work processes in that time period, with a median DWA of 0.9 microgram/m3. Machining process DWAs accounted for the majority of DWAs exceeding the 2.0 micrograms/m3 OSHA standard, with 8.1% of machining DWAs above the standard. We conclude that lowering machining process-related exposures may be important to lowering risk of beryllium disease.

  4. The Moon Mineralogy Mapper (M3) imaging spectrometer for lunar science: Instrument description, calibration, on-orbit measurements, science data calibration and on-orbit validation

    Science.gov (United States)

    Green, R.O.; Pieters, C.; Mouroulis, P.; Eastwood, M.; Boardman, J.; Glavich, T.; Isaacson, P.; Annadurai, M.; Besse, S.; Barr, D.; Buratti, B.; Cate, D.; Chatterjee, A.; Clark, R.; Cheek, L.; Combe, J.; Dhingra, D.; Essandoh, V.; Geier, S.; Goswami, J.N.; Green, R.; Haemmerle, V.; Head, J.; Hovland, L.; Hyman, S.; Klima, R.; Koch, T.; Kramer, G.; Kumar, A.S.K.; Lee, Kenneth; Lundeen, S.; Malaret, E.; McCord, T.; McLaughlin, S.; Mustard, J.; Nettles, J.; Petro, N.; Plourde, K.; Racho, C.; Rodriquez, J.; Runyon, C.; Sellar, G.; Smith, C.; Sobel, H.; Staid, M.; Sunshine, J.; Taylor, L.; Thaisen, K.; Tompkins, S.; Tseng, H.; Vane, G.; Varanasi, P.; White, M.; Wilson, D.

    2011-01-01

    The NASA Discovery Moon Mineralogy Mapper imaging spectrometer was selected to pursue a wide range of science objectives requiring measurement of composition at fine spatial scales over the full lunar surface. To pursue these objectives, a broad spectral range imaging spectrometer with high uniformity and high signal-to-noise ratio capable of measuring compositionally diagnostic spectral absorption features from a wide variety of known and possible lunar materials was required. For this purpose the Moon Mineralogy Mapper imaging spectrometer was designed and developed that measures the spectral range from 430 to 3000 nm with 10 nm spectral sampling through a 24 degree field of view with 0.7 milliradian spatial sampling. The instrument has a signal-to-noise ratio of greater than 400 for the specified equatorial reference radiance and greater than 100 for the polar reference radiance. The spectral cross-track uniformity is >90% and spectral instantaneous field-of-view uniformity is >90%. The Moon Mineralogy Mapper was launched on Chandrayaan-1 on the 22nd of October. On the 18th of November 2008 the Moon Mineralogy Mapper was turned on and collected a first light data set within 24 h. During this early checkout period and throughout the mission the spacecraft thermal environment and orbital parameters varied more than expected and placed operational and data quality constraints on the measurements. On the 29th of August 2009, spacecraft communication was lost. Over the course of the flight mission 1542 downlinked data sets were acquired that provide coverage of more than 95% of the lunar surface. An end-to-end science data calibration system was developed and all measurements have been passed through this system and delivered to the Planetary Data System (PDS.NASA.GOV). An extensive effort has been undertaken by the science team to validate the Moon Mineralogy Mapper science measurements in the context of the mission objectives. A focused spectral, radiometric

  5. RR Lyrae stars in the outer region of the globular cluster M3: a shortage of long periods at r ~ 3.5 to 6 arcmin ?

    CERN Document Server

    Butler, D J

    2004-01-01

    An analysis of the radial distribution of ab-type RR Lyrae star periods in the outer region of the globular cluster M3 at r >= 0.83 arcmin has been performed. That analysis points towards a real shortage of stars with long periods in the radial distance range 3.5 to 6 arcmin (or about 7 to 12 core radii). A brief discussion is presented. The origin of the phenomenon remains an open question.

  6. Compressive Spectral Renormalization Method

    CERN Document Server

    Bayindir, Cihan

    2016-01-01

    In this paper a novel numerical scheme for finding the sparse self-localized states of a nonlinear system of equations with missing spectral data is introduced. As in the Petviashivili's and the spectral renormalization method, the governing equation is transformed into Fourier domain, but the iterations are performed for far fewer number of spectral components (M) than classical versions of the these methods with higher number of spectral components (N). After the converge criteria is achieved for M components, N component signal is reconstructed from M components by using the l1 minimization technique of the compressive sampling. This method can be named as compressive spectral renormalization (CSRM) method. The main advantage of the CSRM is that, it is capable of finding the sparse self-localized states of the evolution equation(s) with many spectral data missing.

  7. Spectral analysis of signals the missing data case

    CERN Document Server

    Wang, Yanwei

    2006-01-01

    Spectral estimation is important in many fields including astronomy, meteorology, seismology, communications, economics, speech analysis, medical imaging, radar, sonar, and underwater acoustics. Most existing spectral estimation algorithms are devised for uniformly sampled complete-data sequences. However, the spectral estimation for data sequences with missing samples is also important in many applications ranging from astronomical time series analysis to synthetic aperture radar imaging with angular diversity. For spectral estimation in the missing-data case, the challenge is how to extend t

  8. A Spectral Atlas of F and G Stars

    Institute of Scientific and Technical Information of China (English)

    V.G.Klochkova; Gang Zhao; V.E.Panchuk; S.V.Ermakov

    2004-01-01

    We present an atlas of a group of bright stars in the range of spectral classes F-G and luminosity classes Ⅰ-Ⅴ.The spectra were obtained with spectral resolution R ~ 15 000 within spectral region 4500-6620 A.Typical spectra of stars with different metallicity [Fe/H] are included.We also show the digital version of the spectral data in FITS format.

  9. CCN Spectral Measurements

    Energy Technology Data Exchange (ETDEWEB)

    Hudson, James G.

    2009-02-27

    Detailed aircraft measurements were made of cloud condensation nuclei (CCN) spectra associated with extensive cloud systems off the central California coast in the July 2005 MASE project. These measurements include the wide supersaturation (S) range (2-0.01%) that is important for these polluted stratus clouds. Concentrations were usually characteristic of continental/anthropogenic air masses. The most notable feature was the consistently higher concentrations above the clouds than below. CCN measurements are so important because they provide a link between atmospheric chemistry and cloud-climate effects, which are the largest climate uncertainty. Extensive comparisons throughout the eleven flights between two CCN spectrometers operated at different but overlapping S ranges displayed the precision and accuracy of these difficult spectral determinations. There are enough channels of resolution in these instruments to provide differential spectra, which produce more rigorous and precise comparisons than traditional cumulative presentations of CCN concentrations. Differential spectra are also more revealing than cumulative spectra. Only one of the eleven flights exhibited typical maritime concentrations. Average below cloud concentrations over the two hours furthest from the coast for the 8 flights with low polluted stratus was 614?233 at 1% S, 149?60 at 0.1% S and 57?33 at 0.04% S cm-3. Immediately above cloud average concentrations were respectively 74%, 55%, and 18% higher. Concentration variability among those 8 flights was a factor of two. Variability within each flight excluding distances close to the coast ranged from 15-56% at 1% S. However, CN and probably CCN concentrations sometimes varied by less than 1% over distances of more than a km. Volatility and size-critical S measurements indicated that the air masses were very polluted throughout MASE. The aerosol above the clouds was more polluted than the below cloud aerosol. These high CCN concentrations from

  10. Rayleigh imaging in spectral mammography

    Science.gov (United States)

    Berggren, Karl; Danielsson, Mats; Fredenberg, Erik

    2016-03-01

    Spectral imaging is the acquisition of multiple images of an object at different energy spectra. In mammography, dual-energy imaging (spectral imaging with two energy levels) has been investigated for several applications, in particular material decomposition, which allows for quantitative analysis of breast composition and quantitative contrast-enhanced imaging. Material decomposition with dual-energy imaging is based on the assumption that there are two dominant photon interaction effects that determine linear attenuation: the photoelectric effect and Compton scattering. This assumption limits the number of basis materials, i.e. the number of materials that are possible to differentiate between, to two. However, Rayleigh scattering may account for more than 10% of the linear attenuation in the mammography energy range. In this work, we show that a modified version of a scanning multi-slit spectral photon-counting mammography system is able to acquire three images at different spectra and can be used for triple-energy imaging. We further show that triple-energy imaging in combination with the efficient scatter rejection of the system enables measurement of Rayleigh scattering, which adds an additional energy dependency to the linear attenuation and enables material decomposition with three basis materials. Three available basis materials have the potential to improve virtually all applications of spectral imaging.

  11. The other spectral flow

    CERN Document Server

    Gato-Rivera, Beatriz; Gato-Rivera, Beatriz; Rosado, Jose Ignacio

    1995-01-01

    Recently we showed that the spectral flow acting on the N=2 twisted topological theories gives rise to a topological algebra automorphism. Here we point out that the untwisting of that automorphism leads to a spectral flow on the untwisted N=2 superconformal algebra which is different from the usual one. This "other" spectral flow does not interpolate between the chiral ring and the antichiral ring. In particular, it maps the chiral ring into the chiral ring and the antichiral ring into the antichiral ring. We discuss the similarities and differences between both spectral flows. We also analyze their action on null states.

  12. Range Tracing

    OpenAIRE

    Jenke, Philipp; Huhle, Benjamin

    2010-01-01

    In this report, we tackle the problem of merging an arbitrary number of range scans (depth images) into a single surface mesh. The mesh-based representation is superior to point-based approaches since it contains important connectivity information. Most previous mesh-based merge methods, however, lose surface details by using simplifying intermediate surface representations (e.g.\\ implicit functions). Such details are essential for further processing steps, especially for feature-preserving r...

  13. Variable Free Spectral Range Spherical Mirror Fabry-Perot Interferometer

    CERN Document Server

    Kerner, K; Yashchuk, V V; Budker, D; Kerner, Katherine; Rochester, Simon M.; Yashchuk, Valeriy V.

    2003-01-01

    A spherical Fabry-Perot interferometer with adjustable mirror spacing is used to produce interference fringes with frequency separation (c/2L)/N, N=2-15. The conditions for observation of these fringes are derived from the consideration of the eigenmodes of the cavity with high transverse indices.

  14. Extension of the spectral range of the CLIO FEL

    Energy Technology Data Exchange (ETDEWEB)

    Marcouille, O.; Boyer, J.C.; Corlier, M. [LURE, Orsay (France)] [and others

    1995-12-31

    The CLIO FEL has been designed to lase between 2 and 20 {mu}m. The electrons are produced by a 32/50 MeV RF linear accelerator. The injector is a 100 keV thermoionic gun, followed by a subharmonic prebuncher at 0.5 GHz and a buncher at 3 GHz. The electron beam is then accelerated in a 4.5 m long travelling wave accelerating section, to the nominal energy. The undulator consisted of 48 periods of 40 mm and the optical cavity is 4.8 m long which corresponds to a 1.2 m Rayleigh length. The peak power extracted by a ZnSe Brewster plate is 10 MW at 10 {mu}. But, beyond 11{mu}m, the laser power decreases rapidely and no laser oscillation appears above 17 {mu}m. In order to lase at farther wavelengths, few changes have been made: First of all, the power limit is due to the diffraction losses of the undulator vaccuum chamber (7 mm height and 2 m long). Numerical calculations have been made and show that cavity losses reach 55 % at 15 {mu}m whereas the measured gain is 60 %. Consequently, the undulator vaccuum chamber have been replaced by a approximately twice bigger one. Then, the minimum gap is increased and the maximum deflection parameter K is reduced by a factor 2: laser tunability is greatly reduced. This why a new undulator has been built. The main characteristics are summarized.

  15. VARIABILITY STUDIES IN M3 GENERATION IN BLACKGRAM (VIGNA MUNGO (L.HEPPER

    Directory of Open Access Journals (Sweden)

    M P MESHRAM

    2013-12-01

    Full Text Available In the present study, pure line seeds of black gram variety viz. T-9, TPU-4 and one promising genotype AKU-18 was treated with gamma irradiation (15kR, 25kR and 35kR with the objective to assess the variability in M3 generation.. Highest GCV and PCV and high estimates of heritability were recorded for the characters sprouting percentage, number of pods plant-1 and grain yield plant-1 (g. High heritability accompanied with high genetic advance was recorded for number of pods plant-1 governed by additive gene effects and therefore selection based on phenotypic performance will be useful to improve character in future.

  16. Trimble M3 1” and South Nts-362R Total Station Angle Measurement Accuracy Analysis

    Directory of Open Access Journals (Sweden)

    Oleniacz Grzegorz

    2017-03-01

    Full Text Available The main purpose of this study was to obtain information about the actual precision of angle measurements with two instruments (Trimble M3 1 "and South NTS-362R, realizable in given measurement conditions. This object is achieved by using a simplified method of testing instruments contained in the PN-ISO 17123-3 standard [1]. This is a continuation of research described in [2], carried out on the same test base, but this time in a different, less favorable field conditions. The use of the same instrument has created an opportunity to compare and analyze the measurement results. The scope of work includes the measurement and results preparation along with statistical processing of the obtained results for both instruments.

  17. Electrodialytic remediation of CCA-treated waste wood in a 2 m3 pilot plant

    DEFF Research Database (Denmark)

    Christensen, Iben Vernegren; Pedersen, Anne Juul; Ottosen, Lisbeth M.;

    2006-01-01

    Waste wood that has been treated with chromated-copper-arsenate (CCA) poses a potential environmental problem due to the content of copper, chromium and arsenic. A pilot plant for electrodialytic remediation of up to 2 m3 wood has been designed and tested and the results are presented here. Several...... fractions. The best remediation efficiency was obtained in an experiment with an electrode distance of 60 cm, and 100 kg wood chips. In this experiment 87% copper, 81% chromium and > 95% arsenic were removed. One other experiment was also analysed for arsenic. In this experiment the distance between...... the working electrodes was 1.5 m and here 95% As was removed. The results showed that arsenic may be the easiest removable of the copper, chromium and arsenic investigated here. This is very encouraging since arsenic is the CCA components of most environmental concern....

  18. Variable Star Status of Two Stars: V204 and I-I-39 in M3

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The star I-I-42 (=vZ1390), a cluster member in M3, located near the red edge of the instability strip of the horizontal branch, was discovered by Roberts and Sandage as a low amplitude variable, it was designated as V204 in the "second catalogue of variable stars in globular clusters", but its coordinates given in all versions of this catalogue are wrong since 1955. We argue that V204 is indeed a low amplitude HB variable star, located near to the red edge of the instability strip, with a period of 0.74785d and an amplitude of about 0.04 mag in V. We also find that the red cluster member star I-I-39 is a low amplitude variable with a period of 1.16d and amplitude of about 0.03 mag in V which might be pulsating at the second overtone.

  19. Modeling of lithium granule injection in NSTX using M3D-C1

    Science.gov (United States)

    Fil, A.; Kolemen, E.; Ferraro, N.; Jardin, S.; Parks, P. B.; Lunsford, R.; Maingi, R.

    2017-05-01

    In this paper, we present simulations of pedestal control by lithium granule injection (LGI) in NSTX. A model for small granule ablation has been implemented in the M3D-C1 code (Jardin et al 2012 Comput. Sci. Discovery 5 014002), allowing the simulation of realistic lithium granule injections. 2D and 3D simulations of Li injections in NSTX H-mode plasmas are performed and the effect of granule size, injection angle and velocity on the pedestal gradient increase is studied. The amplitude of the local pressure perturbation caused by the granules is found to be highly dependent on the solid granule size. Adjusting the granule injection velocity allows one to inject more particles at the pedestal top. 3D simulations show the destabilization of high order MHD modes whose amplitude is directly linked to the localized pressure perturbation, which is found to depend on the toroidal localization of the granule density source.

  20. CH5M3D: an HTML5 program for creating 3D molecular structures.

    Science.gov (United States)

    Earley, Clarke W

    2013-11-18

    While a number of programs and web-based applications are available for the interactive display of 3-dimensional molecular structures, few of these provide the ability to edit these structures. For this reason, we have developed a library written in JavaScript to allow for the simple creation of web-based applications that should run on any browser capable of rendering HTML5 web pages. While our primary interest in developing this application was for educational use, it may also prove useful to researchers who want a light-weight application for viewing and editing small molecular structures. Molecular compounds are drawn on the HTML5 Canvas element, with the JavaScript code making use of standard techniques to allow display of three-dimensional structures on a two-dimensional canvas. Information about the structure (bond lengths, bond angles, and dihedral angles) can be obtained using a mouse or other pointing device. Both atoms and bonds can be added or deleted, and rotation about bonds is allowed. Routines are provided to read structures either from the web server or from the user's computer, and creation of galleries of structures can be accomplished with only a few lines of code. Documentation and examples are provided to demonstrate how users can access all of the molecular information for creation of web pages with more advanced features. A light-weight (≈ 75 kb) JavaScript library has been made available that allows for the simple creation of web pages containing interactive 3-dimensional molecular structures. Although this library is designed to create web pages, a web server is not required. Installation on a web server is straightforward and does not require any server-side modules or special permissions. The ch5m3d.js library has been released under the GNU GPL version 3 open-source license and is available from http://sourceforge.net/projects/ch5m3d/.

  1. Nonlinear spectral imaging of biological tissues

    Science.gov (United States)

    Palero, J. A.

    2007-07-01

    The work presented in this thesis demonstrates live high resolution 3D imaging of tissue in its native state and environment. The nonlinear interaction between focussed femtosecond light pulses and the biological tissue results in the emission of natural autofluorescence and second-harmonic signal. Because biological intrinsic emission is generally very weak and extends from the ultraviolet to the visible spectral range, a broad-spectral range and high sensitivity 3D spectral imaging system is developed. Imaging the spectral characteristics of the biological intrinsic emission reveals the structure and biochemistry of the cells and extra-cellular components. By using different methods in visualizing the spectral images, discrimination between different tissue structures is achieved without the use of any stain or fluorescent label. For instance, RGB real color spectral images of the intrinsic emission of mouse skin tissues show blue cells, green hair follicles, and purple collagen fibers. The color signature of each tissue component is directly related to its characteristic emission spectrum. The results of this study show that skin tissue nonlinear intrinsic emission is mainly due to the autofluorescence of reduced nicotinamide adenine dinucleotide (phosphate), flavins, keratin, melanin, phospholipids, elastin and collagen and nonlinear Raman scattering and second-harmonic generation in Type I collagen. In vivo time-lapse spectral imaging is implemented to study metabolic changes in epidermal cells in tissues. Optical scattering in tissues, a key factor in determining the maximum achievable imaging depth, is also investigated in this work.

  2. Tilting structures in inverse perovskites, M3TtO (M = Ca, Sr, Ba, Eu; Tt = Si, Ge, Sn, Pb).

    Science.gov (United States)

    Nuss, Jürgen; Mühle, Claus; Hayama, Kyouhei; Abdolazimi, Vahideh; Takagi, Hidenori

    2015-06-01

    Single-crystal X-ray diffraction experiments were performed for a series of inverse perovskites, M3TtO (M = Ca, Sr, Ba, Eu; Tt = tetrel element: Si, Ge, Sn, Pb) in the temperature range 500-50 K. For Tt = Sn, Pb, they crystallize as an 'ideal' perovskite-type structure (Pm3m, cP5); however, all of them show distinct anisotropies of the displacement ellipsoids of the M atoms at room temperature. This behavior vanishes on cooling for M = Ca, Sr, Eu, and the structures can be regarded as `ideal' cubic perovskites at 50 K. The anisotropies of the displacement ellipsoids are much more enhanced in the case of the Ba compounds. Finally, their structures undergo a phase transition at ∼ 150 K. They change from cubic to orthorhombic (Ibmm, oI20) upon cooling, with slightly tilted OBa6 octahedra, and bonding angles O-Ba-O ≃ 174° (100 K). For the larger Ba(2+) cations, the structural changes are in agreement with smaller tolerance factors (t) as defined by Goldschmidt. Similar structural behavior is observed for Ca3TtO. Smaller Tt(4-) anions (Si, Ge) introduce reduced tolerance factors. Both compounds Ca3SiO and Ca3GeO with cubic structures at 500 K, change into orthorhombic (Ibmm) at room temperature. Whereby, Ca3SiO is the only representative within the M3TtO family where three polymorphs can be found within the temperature range 500-50 K: Pm3m-Ibmm-Pbnm. They show tiny differences in the tilting of the OCa6 octahedra, expressed by O-Ca-O bond angles of 180° (500 K), ∼ 174° (295 K) and 170° (100 K). For larger M (Sr, Eu, Ba), together with smaller Tt (Si, Ge) atoms, pronounced tilting of the OM6 octahedra, and bonding angles of O-M-O ≃ 160° (295 K) are observed. They crystallize in the anti-GdFeO3 type of structure (Pbnm, oP20), and no phase transitions occur between 500 and 50 K. The observed phase transitions are all accompanied by multiple twinning, in terms of pseudo-merohedry or reticular pseudo-merohedry.

  3. On Longitudinal Spectral Coherence

    DEFF Research Database (Denmark)

    Kristensen, Leif

    1979-01-01

    It is demonstrated that the longitudinal spectral coherence differs significantly from the transversal spectral coherence in its dependence on displacement and frequency. An expression for the longitudinal coherence is derived and it is shown how the scale of turbulence, the displacement between...

  4. Spectral geometry of spacetime

    CERN Document Server

    Kopf, T

    2000-01-01

    Spacetime, understood as a globally hyperbolic manifold, may be characterized by spectral data using a 3+1 splitting into space and time, a description of space by spectral triples and by employing causal relationships, as proposed earlier. Here, it is proposed to use the Hadamard condition of quantum field theory as a smoothness principle.

  5. Hydrocarbon Spectral Database

    Science.gov (United States)

    SRD 115 Hydrocarbon Spectral Database (Web, free access)   All of the rotational spectral lines observed and reported in the open literature for 91 hydrocarbon molecules have been tabulated. The isotopic molecular species, assigned quantum numbers, observed frequency, estimated measurement uncertainty and reference are given for each transition reported.

  6. USGS Spectral Library Version 7

    Science.gov (United States)

    Kokaly, Raymond F.; Clark, Roger N.; Swayze, Gregg A.; Livo, K. Eric; Hoefen, Todd M.; Pearson, Neil C.; Wise, Richard A.; Benzel, William M.; Lowers, Heather A.; Driscoll, Rhonda L.; Klein, Anna J.

    2017-04-10

    We have assembled a library of spectra measured with laboratory, field, and airborne spectrometers. The instruments used cover wavelengths from the ultraviolet to the far infrared (0.2 to 200 microns [μm]). Laboratory samples of specific minerals, plants, chemical compounds, and manmade materials were measured. In many cases, samples were purified, so that unique spectral features of a material can be related to its chemical structure. These spectro-chemical links are important for interpreting remotely sensed data collected in the field or from an aircraft or spacecraft. This library also contains physically constructed as well as mathematically computed mixtures. Four different spectrometer types were used to measure spectra in the library: (1) Beckman™ 5270 covering the spectral range 0.2 to 3 µm, (2) standard, high resolution (hi-res), and high-resolution Next Generation (hi-resNG) models of Analytical Spectral Devices (ASD) field portable spectrometers covering the range from 0.35 to 2.5 µm, (3) Nicolet™ Fourier Transform Infra-Red (FTIR) interferometer spectrometers covering the range from about 1.12 to 216 µm, and (4) the NASA Airborne Visible/Infra-Red Imaging Spectrometer AVIRIS, covering the range 0.37 to 2.5 µm. Measurements of rocks, soils, and natural mixtures of minerals were made in laboratory and field settings. Spectra of plant components and vegetation plots, comprising many plant types and species with varying backgrounds, are also in this library. Measurements by airborne spectrometers are included for forested vegetation plots, in which the trees are too tall for measurement by a field spectrometer. This report describes the instruments used, the organization of materials into chapters, metadata descriptions of spectra and samples, and possible artifacts in the spectral measurements. To facilitate greater application of the spectra, the library has also been convolved to selected spectrometer and imaging spectrometers sampling and

  7. Lunar mare deposits associated with the Orientale impact basin: New insights into mineralogy, history, mode of emplacement, and relation to Orientale Basin evolution from Moon Mineralogy Mapper (M3) data from Chandrayaan-1

    Science.gov (United States)

    Whitten, J.; Head, J.W.; Staid, M.; Pieters, C.M.; Mustard, J.; Clark, R.; Nettles, J.; Klima, R.L.; Taylor, L.

    2011-01-01

    Moon Mineralogy Mapper (M3) image and spectral reflectance data are combined to analyze mare basalt units in and adjacent to the Orientale multiring impact basin. Models are assessed for the relationships between basin formation and mare basalt emplacement. Mare basalt emplacement on the western nearside limb began prior to the Orientale event as evidenced by the presence of cryptomaria. The earliest post-Orientale-event mare basalt emplacement occurred in the center of the basin (Mare Orientale) and postdated the formation of the Orientale Basin by about 60-100 Ma. Over the next several hundred million years, basalt patches were emplaced first along the base of the Outer Rook ring (Lacus Veris) and then along the base of the Cordillera ring (Lacus Autumni), with some overlap in ages. The latest basalt patches are as young as some of the youngest basalt deposits on the lunar nearside. M3 data show several previously undetected mare patches on the southwestern margins of the basin interior. Regardless, the previously documented increase in mare abundance from the southwest toward the northeast is still prominent. We attribute this to crustal and lithospheric trends moving from the farside to the nearside, with correspondingly shallower density and thermal barriers to basaltic magma ascent and eruption toward the nearside. The wide range of model ages for Orientale mare deposits (3.70-1.66 Ga) mirrors the range of nearside mare ages, indicating that the small amount of mare fill in Orientale is not due to early cessation of mare emplacement but rather to limited volumes of extrusion for each phase during the entire period of nearside mare basalt volcanism. This suggests that nearside and farside source regions may be similar but that other factors, such as thermal and crustal thickness barriers to magma ascent and eruption, may be determining the abundance of surface deposits on the limbs and farside. The sequence, timing, and elevation of mare basalt deposits

  8. Spectral Geometry and Causality

    CERN Document Server

    Kopf, T

    1996-01-01

    For a physical interpretation of a theory of quantum gravity, it is necessary to recover classical spacetime, at least approximately. However, quantum gravity may eventually provide classical spacetimes by giving spectral data similar to those appearing in noncommutative geometry, rather than by giving directly a spacetime manifold. It is shown that a globally hyperbolic Lorentzian manifold can be given by spectral data. A new phenomenon in the context of spectral geometry is observed: causal relationships. The employment of the causal relationships of spectral data is shown to lead to a highly efficient description of Lorentzian manifolds, indicating the possible usefulness of this approach. Connections to free quantum field theory are discussed for both motivation and physical interpretation. It is conjectured that the necessary spectral data can be generically obtained from an effective field theory having the fundamental structures of generalized quantum mechanics: a decoherence functional and a choice of...

  9. Spectral computations for bounded operators

    CERN Document Server

    Ahues, Mario; Limaye, Balmohan

    2001-01-01

    Exact eigenvalues, eigenvectors, and principal vectors of operators with infinite dimensional ranges can rarely be found. Therefore, one must approximate such operators by finite rank operators, then solve the original eigenvalue problem approximately. Serving as both an outstanding text for graduate students and as a source of current results for research scientists, Spectral Computations for Bounded Operators addresses the issue of solving eigenvalue problems for operators on infinite dimensional spaces. From a review of classical spectral theory through concrete approximation techniques to finite dimensional situations that can be implemented on a computer, this volume illustrates the marriage of pure and applied mathematics. It contains a variety of recent developments, including a new type of approximation that encompasses a variety of approximation methods but is simple to verify in practice. It also suggests a new stopping criterion for the QR Method and outlines advances in both the iterative refineme...

  10. Compositional diversity of near-, far-side transitory zone around Naonobu, Webb and Sinus Successus craters: Inferences from Chandrayaan-1 Moon Mineralogy Mapper (M3) data

    Indian Academy of Sciences (India)

    Rishikesh Bharti; D Ramakrishnan; K D Singh

    2014-02-01

    This study investigated the potential of Moon Mineralogy Mapper (M3) data for studying compositional variation in the near-, far-side transition zone of the lunar surface. For this purpose, the radiance values of the M3 data were corrected for illumination and emission related effects and converted to apparent reflectance. Dimensionality of the calibrated reflectance image cube was reduced using Independent Component Analysis (ICA) and endmembers were extracted by using Pixel Purity Index (PPI) algorithm. The selected endmembers were linearly unmixed and resolved for mineralogy using United States Geological Survey (USGS) library spectra of minerals. These mineralogically resolved endmembers were used to map the compositional variability within, and outside craters using Spectral Angle Mapper (SAM) algorithm. Cross validation for certain litho types was attempted using band ratios like Optical Maturity (OMAT), Color Ratio Composite and Integrated Band Depth ratio (IBD). The identified lithologies for highland and basin areas match well with published works and strongly support depth related magmatic differentiation. Prevalence of pigeonite-basalt, pigeonite-norite and pyroxenite in crater peaks and floors are unique to the investigated area and are attributed to local, lateral compositional variability in magma composition due to pressure, temperature, and rate of cooling.

  11. Constraints on olivine-rich rock types on the Moon as observed by Diviner and M3: Implications for the formation of the lunar crust

    Science.gov (United States)

    Arnold, J. A.; Glotch, T. D.; Lucey, P. G.; Song, E.; Thomas, I. R.; Bowles, N. E.; Greenhagen, B. T.

    2016-07-01

    We place upper limits on lunar olivine abundance using midinfrared (5-25 µm) data from the Lunar Reconnaissance Orbiter Diviner Lunar Radiometer Experiment (Diviner) along with effective emissivity spectra of mineral mixtures in a simulated lunar environment. Olivine-bearing, pyroxene-poor lithologies have been identified on the lunar surface with visible-near-infrared (VNIR) observations. Since the Kaguya Spectral Profiler (SP) VNIR survey of olivine-rich regions is the most complete to date, we focus this work on exposures identified by that study. We first confirmed the locations with VNIR data from the Moon Mineralogy Mapper (M3) instrument. We then developed a Diviner olivine index from our laboratory data which, along with M3 and Lunar Reconnaissance Orbiter Camera wide-angle camera data, was used to select the geographic area over which Diviner emissivity data were extracted. We calculate upper limits on olivine abundance for these areas using laboratory emissivity spectra of anorthite-forsterite mixtures acquired under lunar-like conditions. We find that these exposures have widely varying olivine content. In addition, after applying an albedo-based space weathering correction to the Diviner data, we find that none of the areas are unambiguously consistent with concentrations of forsterite exceeding 90 wt %, in contrast to the higher abundance estimates derived from VNIR data.

  12. M3 Macrophages Stop Division of Tumor Cells In Vitro and Extend Survival of Mice with Ehrlich Ascites Carcinoma.

    Science.gov (United States)

    Kalish, Sergey; Lyamina, Svetlana; Manukhina, Eugenia; Malyshev, Yuri; Raetskaya, Anastasiya; Malyshev, Igor

    2017-01-26

    BACKGROUND M1 macrophages target tumor cells. However, many tumors produce anti-inflammatory cytokines, which reprogram the anti-tumor M1 macrophages into the pro-tumor M2 macrophages. We have hypothesized that the problem of pro-tumor macrophage reprogramming could be solved by using a special M3 switch phenotype. The M3 macrophages, in contrast to the M1 macrophages, should respond to anti-inflammatory cytokines by increasing production of pro-inflammatory cytokines to retain its anti-tumor properties. Objectives of the study were to form an M3 switch phenotype in vitro and to evaluate the effect of M3 macrophages on growth of Ehrlich ascites carcinoma (EAC) in vitro and in vivo. MATERIAL AND METHODS Tumor growth was initiated by an intraperitoneal injection of EAC cells into C57BL/6J mice. RESULTS 1) The M3 switch phenotype can be programed by activation of M1-reprogramming pathways with simultaneous inhibition of the M2 phenotype transcription factors, STAT3, STAT6, and/or SMAD3. 2) M3 macrophages exerted an anti-tumor effect both in vitro and in vivo, which was superior to anti-tumor effects of cisplatin or M1 macrophages. 3) The anti-tumor effect of M3 macrophages was due to their anti-proliferative effect. CONCLUSIONS Development of new biotechnologies for restriction of tumor growth using in vitro reprogrammed M3 macrophages is very promising.

  13. M3 Macrophages Stop Division of Tumor Cells In Vitro and Extend Survival of Mice with Ehrlich Ascites Carcinoma

    Science.gov (United States)

    Kalish, Sergey; Lyamina, Svetlana; Manukhina, Eugenia; Malyshev, Yuri; Raetskaya, Anastasiya; Malyshev, Igor

    2017-01-01

    Background M1 macrophages target tumor cells. However, many tumors produce anti-inflammatory cytokines, which reprogram the anti-tumor M1 macrophages into the pro-tumor M2 macrophages. We have hypothesized that the problem of pro-tumor macrophage reprogramming could be solved by using a special M3 switch phenotype. The M3 macrophages, in contrast to the M1 macrophages, should respond to anti-inflammatory cytokines by increasing production of pro-inflammatory cytokines to retain its anti-tumor properties. Objectives of the study were to form an M3 switch phenotype in vitro and to evaluate the effect of M3 macrophages on growth of Ehrlich ascites carcinoma (EAC) in vitro and in vivo. Material/Methods Tumor growth was initiated by an intraperitoneal injection of EAC cells into C57BL/6J mice. Results 1) The M3 switch phenotype can be programed by activation of M1-reprogramming pathways with simultaneous inhibition of the M2 phenotype transcription factors, STAT3, STAT6, and/or SMAD3. 2) M3 macrophages exerted an anti-tumor effect both in vitro and in vivo, which was superior to anti-tumor effects of cisplatin or M1 macrophages. 3) The anti-tumor effect of M3 macrophages was due to their anti-proliferative effect. Conclusions Development of new biotechnologies for restriction of tumor growth using in vitro reprogrammed M3 macrophages is very promising. PMID:28123171

  14. Chemokine Binding Protein M3 of Murine Gammaherpesvirus 68 Modulates the Host Response to Infection in a Natural Host

    Science.gov (United States)

    Hughes, David J.; Kipar, Anja; Leeming, Gail H.; Bennett, Elaine; Howarth, Deborah; Cummerson, Joanne A.; Papoula-Pereira, Rita; Flanagan, Brian F.; Sample, Jeffery T.; Stewart, James P.

    2011-01-01

    Murine γ-herpesvirus 68 (MHV-68) infection of Mus musculus-derived strains of mice is an attractive model of γ-herpesvirus infection. Surprisingly, however, ablation of expression of MHV-68 M3, a secreted protein with broad chemokine-binding properties in vitro, has no discernable effect during experimental infection via the respiratory tract. Here we demonstrate that M3 indeed contributes significantly to MHV-68 infection, but only in the context of a natural host, the wood mouse (Apodemus sylvaticus). Specifically, M3 was essential for two features unique to the wood mouse: virus-dependent inducible bronchus-associated lymphoid tissue (iBALT) in the lung and highly organized secondary follicles in the spleen, both predominant sites of latency in these organs. Consequently, lack of M3 resulted in substantially reduced latency in the spleen and lung. In the absence of M3, splenic germinal centers appeared as previously described for MHV-68-infected laboratory strains of mice, further evidence that M3 is not fully functional in the established model host. Finally, analyses of M3's influence on chemokine and cytokine levels within the lungs of infected wood mice were consistent with the known chemokine-binding profile of M3, and revealed additional influences that provide further insight into its role in MHV-68 biology. PMID:21445235

  15. Chemokine binding protein M3 of murine gammaherpesvirus 68 modulates the host response to infection in a natural host.

    Directory of Open Access Journals (Sweden)

    David J Hughes

    2011-03-01

    Full Text Available Murine γ-herpesvirus 68 (MHV-68 infection of Mus musculus-derived strains of mice is an attractive model of γ-herpesvirus infection. Surprisingly, however, ablation of expression of MHV-68 M3, a secreted protein with broad chemokine-binding properties in vitro, has no discernable effect during experimental infection via the respiratory tract. Here we demonstrate that M3 indeed contributes significantly to MHV-68 infection, but only in the context of a natural host, the wood mouse (Apodemus sylvaticus. Specifically, M3 was essential for two features unique to the wood mouse: virus-dependent inducible bronchus-associated lymphoid tissue (iBALT in the lung and highly organized secondary follicles in the spleen, both predominant sites of latency in these organs. Consequently, lack of M3 resulted in substantially reduced latency in the spleen and lung. In the absence of M3, splenic germinal centers appeared as previously described for MHV-68-infected laboratory strains of mice, further evidence that M3 is not fully functional in the established model host. Finally, analyses of M3's influence on chemokine and cytokine levels within the lungs of infected wood mice were consistent with the known chemokine-binding profile of M3, and revealed additional influences that provide further insight into its role in MHV-68 biology.

  16. Limit of Spectral Resolution in Terahertz Time-Domain Spectroscopy

    Institute of Scientific and Technical Information of China (English)

    Jingzhou Xu; Tao Yuan; Samuel Mickan; X.-C.Zhang

    2003-01-01

    The pulsed nature of terahertz time-domain spectroscopy (THz-TDS) sets a fundamental limit on its spectral resolution. The spectral resolution of THz-TDS can be improved by increasing the duration of the temporal measurement, but is limited by the dynamic range of the system in the time domain. This paper presents calculations and experimental results relating the temporal dynamic range of a THz-TDS system to its spectral resolution. We discuss three typical terahertz sources in terms of their dynamic range and hence achievable spectral resolution.

  17. Snapshot spectral imaging system

    Science.gov (United States)

    Arnold, Thomas; De Biasio, Martin; McGunnigle, Gerald; Leitner, Raimund

    2010-02-01

    Spectral imaging is the combination of spectroscopy and imaging. These fields are well developed and are used intensively in many application fields including industry and the life sciences. The classical approach to acquire hyper-spectral data is to sequentially scan a sample in space or wavelength. These acquisition methods are time consuming because only two spatial dimensions, or one spatial and the spectral dimension, can be acquired simultaneously. With a computed tomography imaging spectrometer (CTIS) it is possible to acquire two spatial dimensions and a spectral dimension during a single integration time, without scanning either spatial or spectral dimensions. This makes it possible to acquire dynamic image scenes without spatial registration of the hyperspectral data. This is advantageous compared to tunable filter based systems which need sophisticated image registration techniques. While tunable filters provide full spatial and spectral resolution, for CTIS systems there is always a tradeoff between spatial and spectral resolution as the spatial and spectral information corresponding to an image cube is squeezed onto a 2D image. The presented CTIS system uses a spectral-dispersion element to project the spectral and spatial image information onto a 2D CCD camera array. The system presented in this paper is designed for a microscopy application for the analysis of fixed specimens in pathology and cytogenetics, cell imaging and material analysis. However, the CTIS approach is not limited to microscopy applications, thus it would be possible to implement it in a hand-held device for e.g. real-time, intra-surgery tissue classification.

  18. Soluble M3 proteins of murine gammaherpesviruses 68 and 72 expressed in Escherichia coli: analysis of chemokine-binding properties.

    Science.gov (United States)

    Matúšková, R; Pančík, P; Štibrániová, I; Belvončíková, P; Režuchová, I; Kúdelová, M

    2015-12-01

    M3 protein of murine gammaherpesvirus 68 (MHV-68) was identified as a viral chemokine-binding protein 3 (vCKBP-3) capable to bind a broad spectrum of chemokines and their receptors. During both acute and latent infection MHV-68 M3 protein provides a selective advantage for the virus by inhibiting the antiviral and inflammatory response. A unique mutation Asp307Gly was identified in the M3 protein of murine gammaherpesvirus 72 (MHV-72), localized near chemokine-binding domain. Study on chemokine-binding properties of MHV-72 M3 protein purified from medium of infected cells implied reduced binding to some chemokines when compared to MHV-68 M3 protein. It was suggested that the mutation in the M3 protein might be involved in the attenuation of immune response to infection with MHV-72. Recently, Escherichia coli cells were used to prepare native recombinant M3 proteins of murine gammaherpesviruses 68 and 72 (Pančík et al., 2013). In this study, we assessed the chemokine-binding properties of three M3 proteins prepared in E. coli Rosetta-gami 2 (DE3) cells, the full length M3 protein of both MHV-68 and MHV-72 and MHV-68 M3 protein truncated in the signal sequence (the first 24 aa). They all displayed binding activity to human chemokines CCL5 (RANTES), CXCL8 (IL-8), and CCL3 (MIP-1α). The truncated MHV-68 M3 protein had more than twenty times reduced binding activity to CCL5, but only about five and three times reduced binding to CXCL8 and CCL3 when compared to its full length counterpart. Binding of the full length MHV-72 M3 protein to all chemokines was reduced when compared to MHV-68 M3 protein. Its binding to CCL5 and CCL3 was reduced over ten and seven times. However, its binding to CXCL8 was only slightly reduced (64.8 vs 91.8%). These data implied the significance of the signal sequence and also of a single mutation (at aa 307) for efficient M3 protein binding to some chemokines.

  19. Automated measurement and monitoring of bioprocesses: key elements of the M(3)C strategy.

    Science.gov (United States)

    Sonnleitner, Bernhard

    2013-01-01

    The state-of-routine monitoring items established in the bioprocess industry as well as some important state-of-the-art methods are briefly described and the potential pitfalls discussed. Among those are physical and chemical variables such as temperature, pressure, weight, volume, mass and volumetric flow rates, pH, redox potential, gas partial pressures in the liquid and molar fractions in the gas phase, infrared spectral analysis of the liquid phase, and calorimetry over an entire reactor. Classical as well as new optical versions are addressed. Biomass and bio-activity monitoring (as opposed to "measurement") via turbidity, permittivity, in situ microscopy, and fluorescence are critically analyzed. Some new(er) instrumental analytical tools, interfaced to bioprocesses, are explained. Among those are chromatographic methods, mass spectrometry, flow and sequential injection analyses, field flow fractionation, capillary electrophoresis, and flow cytometry. This chapter surveys the principles of monitoring rather than compiling instruments.

  20. CH5M3D: an HTML5 program for creating 3D molecular structures

    Science.gov (United States)

    2013-01-01

    Background While a number of programs and web-based applications are available for the interactive display of 3-dimensional molecular structures, few of these provide the ability to edit these structures. For this reason, we have developed a library written in JavaScript to allow for the simple creation of web-based applications that should run on any browser capable of rendering HTML5 web pages. While our primary interest in developing this application was for educational use, it may also prove useful to researchers who want a light-weight application for viewing and editing small molecular structures. Results Molecular compounds are drawn on the HTML5 Canvas element, with the JavaScript code making use of standard techniques to allow display of three-dimensional structures on a two-dimensional canvas. Information about the structure (bond lengths, bond angles, and dihedral angles) can be obtained using a mouse or other pointing device. Both atoms and bonds can be added or deleted, and rotation about bonds is allowed. Routines are provided to read structures either from the web server or from the user’s computer, and creation of galleries of structures can be accomplished with only a few lines of code. Documentation and examples are provided to demonstrate how users can access all of the molecular information for creation of web pages with more advanced features. Conclusions A light-weight (≈ 75 kb) JavaScript library has been made available that allows for the simple creation of web pages containing interactive 3-dimensional molecular structures. Although this library is designed to create web pages, a web server is not required. Installation on a web server is straightforward and does not require any server-side modules or special permissions. The ch5m3d.js library has been released under the GNU GPL version 3 open-source license and is available from http://sourceforge.net/projects/ch5m3d/. PMID:24246004

  1. Real-time monitoring of genetically modified Chlamydomonas reinhardtii during the Foton M3 space mission

    Science.gov (United States)

    Lambreva, M.; Rea, G.; Antonacci, A.; Serafini, A.; Damasso, M.; Pastorelli, S.; Margonelli, A.; Johanningmeier, U.; Bertalan, I.; Pezzotti, G.; Giardi, M. T.

    2008-09-01

    Long-term space exploration, colonization or habitation requires biological life support systems capable to cope with the deleterious space environment. The use of oxygenic photosynthetic microrganisms is an intriguing possibility mainly for food, O2 and nutraceutical compounds production. The critical points of utilizing plants- or algae-based life support systems are the microgravity and the ionizing radiation, which can influence the performance of these organisms. The aim of the present study was to assess the effects of space environment on the photosynthetic activity of various microrganisms and to select space stresstolerant strains. Photosystem II D1 protein sitedirected and random mutants of the unicellular green alga Chlamydomonas reinhardtii [1] were used as a model system to test and select the amino acid substitutions capable to account for space stress tolerance. We focussed our studies also on the accumulation of the Photosystem II photoprotective carotenoids (the xantophylls violaxanthin, anteraxanthin and zeaxanthin), powerful antioxidants that epidemiological studies demonstrated to be human vision protectors. For this purpose some mutants modified at the level of enzymes involved in the biosynthesis of xanthophylls were included in the study [2]. To identify the consequences of the space environment on the photosynthetic apparatus the changes in the Photosystem II efficiency were monitored in real time during the ESA-Russian Foton- M3 mission in September 2007. For the space flight a high-tech, multicell fluorescence detector, Photo-II, was designed and built by the Centre for Advanced Research in Space Optics in collaboration with Kayser-Italy, Biosensor and DAS. Photo-II is an automatic device developed to measure the chlorophyll fluorescence and to provide a living conditions for several different algae strains (Fig.1). Twelve different C. reinhardti strains were analytically selected and two replications for each strain were brought to space

  2. Spectral range calculation inside the Research Irradiating Facility Army Technology Center using code MCNPX and comparison with the spectra of energy Caesium 137 raised in laboratory; Calculo gama espectral no interior do irradiador de pesquisa do Centro Tecnologico do Exercito utilizando o codigo MCNPX e comparacao com espectros de energia do Cesio 137 levantados em laboratorio

    Energy Technology Data Exchange (ETDEWEB)

    Gomes, Renato G.; Rebello, Wilson F.; Cavaliere, Marcos Paulo; Vellozo, Sergio O.; Moreira Junior, Luis, E-mail: renatoguedes@ime.eb.br, E-mail: rebello@ime.eb.br, E-mail: eng.cavaliere@gmail.com, E-mail: vellozo@cbpf.br, E-mail: luisjrmoreira@hotmail.com [Instituto Militar de Engenharia (IME), Rio de Janeiro, RJ (Brazil); Vital, Helio C., E-mail: vital@ctex.eb.br [Centro Tecnologico do Exercito (CTEX), Barra de Guaratiba, RJ (Brazil); Silva, Ademir X., E-mail: ademir@con.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil)

    2013-07-01

    Using the MCNPX code, the objective was to calculate by means of computer simulation spectroscopy range inside the irradiation chamber upper radiator gamma research irradiating facility Army Technology Center (CTEx). The calculations were performed in the spectral range usual 2 points for research purposes irradiating the energy spectra of gamma rays from the source of Cesium chloride 137. Sought the discretization of the spectrum in 100 channels at points of upper bound of 1cm higher and lower dose rates previously known. It was also conducted in the laboratory lifting the spectrum of Cesium-137 source using NaI scintillator detector and multichannel analyzer. With the source spectrum Cesium-137 contained in the literature and raised in the laboratory, both used as reference for comparison and analysis in terms of probability of emission maximum of 0.661 MeV The spectra were quite consistent in terms of the behavior of the energy distributions with scores. The position of maximum dose rate showed absorption detection almost maximum energy of 0.661 MeV photopeak In the spectrum of the position of minimum dosage rate, it was found that due to the removal of the source point of interest, some loss detection were caused by Compton scattering. (author)

  3. Spectral Reconstruction for Obtaining Virtual Hyperspectral Images

    Science.gov (United States)

    Perez, G. J. P.; Castro, E. C.

    2016-12-01

    Hyperspectral sensors demonstrated its capabalities in identifying materials and detecting processes in a satellite scene. However, availability of hyperspectral images are limited due to the high development cost of these sensors. Currently, most of the readily available data are from multi-spectral instruments. Spectral reconstruction is an alternative method to address the need for hyperspectral information. The spectral reconstruction technique has been shown to provide a quick and accurate detection of defects in an integrated circuit, recovers damaged parts of frescoes, and it also aids in converting a microscope into an imaging spectrometer. By using several spectral bands together with a spectral library, a spectrum acquired by a sensor can be expressed as a linear superposition of elementary signals. In this study, spectral reconstruction is used to estimate the spectra of different surfaces imaged by Landsat 8. Four atmospherically corrected surface reflectance from three visible bands (499 nm, 585 nm, 670 nm) and one near-infrared band (872 nm) of Landsat 8, and a spectral library of ground elements acquired from the United States Geological Survey (USGS) are used. The spectral library is limited to 420-1020 nm spectral range, and is interpolated at one nanometer resolution. Singular Value Decomposition (SVD) is used to calculate the basis spectra, which are then applied to reconstruct the spectrum. The spectral reconstruction is applied for test cases within the library consisting of vegetation communities. This technique was successful in reconstructing a hyperspectral signal with error of less than 12% for most of the test cases. Hence, this study demonstrated the potential of simulating information at any desired wavelength, creating a virtual hyperspectral sensor without the need for additional satellite bands.

  4. A spectral line survey from 17.5-250 nm of plasmas created in a magnetic confinement device

    Science.gov (United States)

    McCarthy, K. J.; Zurro, B.; Hollmann, E. M.; Hernández Sánchez, J.; TJ-II Team1, the

    2016-11-01

    Spectral emission lines continue to be a powerful tool for studying astrophysical, process, laser-produced, and magnetically confined plasmas, among others. Hence, numerous spectroscopy-based plasma diagnostics, from the x-ray to the infrared, make use of the relative intensity, width, displacement in wavelength, or temporal evolution of such emission lines emitted by the atoms and ions present in such plasmas. In this work, a spectral line survey, from 17.5-250 nm, is presented for electron cyclotron resonance heated (ECRH) and neutral beam injection (NBI) heated plasmas created and maintained in the TJ-II stellarator, a medium-sized magnetically confined plasma device. In these plasmas, for which hydrogen, deuterium or helium have been used as the working gas, central electron temperatures and densities up to 1 keV and 5 × 1019 m-3, respectively, are achieved. This work is a compilation of the identified spectral emission lines emitted by the working gas as well by the intrinsic and injected impurity ions in the above wavelength range. For this, spectra were recorded, over the past fifteen years of TJ-II operation, using a 1 m focal length normal incidence spectrometer equipped with a charge-coupled detector at its output focal plane. In total, almost 400 spectral emission lines from eighteen different elements have been identified using a number of atomic line emission databases.

  5. The Swift/UVOT Stars Survey. II. RR Lyrae Stars in M 3 and M 15

    CERN Document Server

    Siegel, Michael H; Balzer, Benjamin G; Hagen, Lea M Z

    2015-01-01

    We present the first results of an near-ultraviolet (NUV) survey of RR Lyrae stars from the Ultraviolet Optical Telescope (UVOT) aboard the Swift Gamma-Ray Burst Mission. It is well-established that RR Lyrae have large amplitudes in the far- and near-ultraviolet. We have used UVOT's unique wide-field NUV imaging capability to perform the first systematic NUV survey of variable stars in the Galactic globular clusters M 3 and M 15. We identify 280 variable stars, comprising 275 RR Lyrae, two anomalous Cepheids, one classical Cepheid, one SX Phoenicis star and one possible long-period or irregular variable. Only two of these are new discoveries. We compare our results to previous investigations and find excellent agreement in the periods with significantly larger amplitudes in the NUV. We map out, for the first time, an NUV Bailey diagram from globular clusters, showing the usual loci for fundamental mode RRab and first overtone RRc pulsators. We show the unique sensitivity of NUV photometry to both the temperat...

  6. THE SWIFT UVOT STARS SURVEY. II. RR LYRAE STARS IN M3 AND M15

    Energy Technology Data Exchange (ETDEWEB)

    Siegel, Michael H.; Porterfield, Blair L.; Balzer, Benjamin G.; Hagen, Lea M. Z., E-mail: siegel@astro.psu.edu, E-mail: blp14@psu.edu, E-mail: bgb5080@psu.edu, E-mail: lea.zernow.hagen@gmail.com [Pennsylvania State University, Department of Astronomy, 525 Davey Laboratory, University Park, PA 16802 (United States)

    2015-10-15

    We present the first results of a near-ultraviolet (NUV) survey of RR Lyrae stars from the Ultraviolet Optical Telescope (UVOT) on board the Swift Gamma-ray Burst Mission. It is well-established that RR Lyrae stars have large amplitudes in the far- and near-ultraviolet. We have used UVOT’s unique wide-field NUV imaging capability to perform the first systematic NUV survey of variable stars in the Galactic globular clusters M3 and M15. We identify 280 variable stars, comprised of 275 RR Lyrae, 2 anomalous Cepheids, 1 classical Cepheid, 1 SX Phoenicis star, and 1 possible long-period or irregular variable. Only two of these are new discoveries. We compare our results to previous investigations and find excellent agreement in the periods with significantly larger amplitudes in the NUV. We map out, for the first time, an NUV Bailey diagram from globular clusters, showing the usual loci for fundamental mode RRab and first overtone RRc pulsators. We show the unique sensitivity of NUV photometry to both the temperatures and the surface gravities of RR Lyrae stars. Finally, we show evidence of an NUV period–metallicity–luminosity relationship. Future investigations will further examine the dependence of NUV pulsation parameters on metallicity and Oosterhoff classification.

  7. Molecular Modeling of the M3 Acetylcholine Muscarinic Receptor and Its Binding Site

    Science.gov (United States)

    Martinez-Archundia, Marlet; Cordomi, Arnau; Garriga, Pere; Perez, Juan J.

    2012-01-01

    The present study reports the results of a combined computational and site mutagenesis study designed to provide new insights into the orthosteric binding site of the human M3 muscarinic acetylcholine receptor. For this purpose a three-dimensional structure of the receptor at atomic resolution was built by homology modeling, using the crystallographic structure of bovine rhodopsin as a template. Then, the antagonist N-methylscopolamine was docked in the model and subsequently embedded in a lipid bilayer for its refinement using molecular dynamics simulations. Two different lipid bilayer compositions were studied: one component palmitoyl-oleyl phosphatidylcholine (POPC) and two-component palmitoyl-oleyl phosphatidylcholine/palmitoyl-oleyl phosphatidylserine (POPC-POPS). Analysis of the results suggested that residues F222 and T235 may contribute to the ligand-receptor recognition. Accordingly, alanine mutants at positions 222 and 235 were constructed, expressed, and their binding properties determined. The results confirmed the role of these residues in modulating the binding affinity of the ligand. PMID:22500107

  8. [Gerbil experiment in the flight of spacecraft "Foton-M3"].

    Science.gov (United States)

    Il'in, E A; Smirnov, I A; Soldatov, P E; Orlov, O I

    2009-01-01

    The 12-d mission of Russian spacecraft Foton-M3 in September of 2007 was used as an opportunity to fly an experiment with 12 male gerbils (Meriones unguiculatus) at the age of 4-4.5 mos. and mean body weight of 51.6 grams. Considering the behavior pattern of these animals, selection and preparation of the experimental groups continued in the course of 2.5-3 months. The flight animals were contained in module Kontur-L outfitted with a self-sustained system of life support. In orbit, the animals received a palletized hydrogenous feed. The physiological and hygienic parameters of the gerbil environment during the flight complied with the official standards. Analysis of the video recorded behavior of animals in microgravity showed that virtually throughout the flight they moved chaotically along the cage never attempting to stabilize position catching at the wire netting of the cage. The animals were decapitated in 21-24 hours after landing. The investigations showed that structural and functional changes in gerbil organs and tissues were generally of the same type as in rats following fights of comparable duration. However, some differences between the animals were attributed to the specifics of water turnover in gerbils.

  9. [Glycogen content in gerbil's liver following the spacecraft Foton-M3 mission].

    Science.gov (United States)

    Atiakshin, D A; Bykov, E G; Il'in, E A; Pashkov, A N

    2009-01-01

    Glycogen cytochemistry and distribution in hepatocytes of the classic liver lobules were studied in three groups of gerbils Meriones unguiculatus: vivarium, synchronous control and flown in the 12-d Foton-M3 mission. The control animals were shown to have the central glycogen distribution with a large pool of polysaccharides found in hepatocytes of the pericentral and intermediate lobules and a small pool in the periportal area. Glycogen in hepatocyte plasm was within the physiological norm in the alpha- and beta-granules, typically localized on the cell periphery. Exposure to the spaceflight conditions decreased significantly glycogen concentrations in each functional region of the hepatic lobules and reduced the gradient of polysaccharide distribution from the portal triads toward the central vein. In parallel, high glycogen heterogeneity formed in adjacent hepatocytes and loci. The presence of glycosomes evidenced disturbance of carbohydrates metabolism. In addition, intracellular topography of glycogen granules in cytoplasm was altered. Trends of glycogen in gerbils of the synchronous control were similar to the space flown animals but much less pronounced.

  10. [Jejunum intersticium in mongolian gerbils after the flight on spacecraft Foton-M3].

    Science.gov (United States)

    Atiashkin, D A; Bykov, É G; Il'in, E A; Pashkov, A N

    2012-01-01

    Methods of light optical microscopy were used to explore histoarchitectonics, topography and tinctorial properties of the extracellular phase of fibers of jejunum wall intersticium in Mongolian gerbils following 12-day orbital flight aboard Foton-M3, ground-based simulation of the spaceflight factors in the KONTUR-L facility, and in the group of biological control Postflight destructive changes were found in reticulin fibers (type-III collagen) of villi stroma, intercrypt intersticium and submucosa. Local acidophilia and fiber homogenization formed in type I collagen present in the intestinal subserous layer, muscular layers endomysium and submucose against the background of progressing edema and arterial, venous plethora and lymphostasis. Elastic component of the intersticium was disarranged in the structures of internal elastic membrane of submucous vessels, fragmented and partly reduced. Simulation of the orbital factors, except for microgravity, in the KONTUR-L facility called forth similar, although less often and diffuse, changes in intersticium fibers. The results of examination of intestinal intersticium fibers in the vivarium control gerbils discovered expressed species characters that should be taken into account by investigators, especially when comparing with data obtained from other animal species.

  11. [Rna content of gerbil hepatocytes after the flight aboard space platform Foton-M3].

    Science.gov (United States)

    Atiashkin, D A; Bykov, E G; Il'in, E A; Pashkov, A N

    2010-01-01

    The paper compares and contrasts the results of measuring the hepatocyte cytoplasm area and RNA content in 35 gerbils in three series of experiments, i.e. the vivarium control, modeled space flight (synchronous control) and exposure to the factors of 12-d Foton-M3 orbital flight. Central, intermediate and peripheral zones of hepatic lobes were subjected to histological and histochemical analyses to measure the hepatocyte cytoplasm area; the RNA content was determined from the level of cytoplasm basophilia after azure staining. Cytometric and cytophotometric investigations were performed using image analyzer Video-7-Test-Morpho. In the vivarium animals, hepatocytes with the largest cytoplasm localized predominantly in the intermediate and central zones of the lobes. Judging from the results of microdensitometry, the RNA content was particularly high in binucleate hepatocytes of the intermediate zone. In the synchronous control, hepatocytes tended to grow in size, in the peripheral zone specifically, whereas RNA content was largely equal no matter hepatocyte topography. After space flight, cytoplasm enlargement transcended this process in the vivarium animals. The cytoplasm RNA content along the entire liver parenchyma made a significant decrease equally as compared with the vivarium and synchronous control animals.

  12. Molecular Modeling of the M3 Acetylcholine Muscarinic Receptor and Its Binding Site

    Directory of Open Access Journals (Sweden)

    Marlet Martinez-Archundia

    2012-01-01

    Full Text Available The present study reports the results of a combined computational and site mutagenesis study designed to provide new insights into the orthosteric binding site of the human M3 muscarinic acetylcholine receptor. For this purpose a three-dimensional structure of the receptor at atomic resolution was built by homology modeling, using the crystallographic structure of bovine rhodopsin as a template. Then, the antagonist N-methylscopolamine was docked in the model and subsequently embedded in a lipid bilayer for its refinement using molecular dynamics simulations. Two different lipid bilayer compositions were studied: one component palmitoyl-oleyl phosphatidylcholine (POPC and two-component palmitoyl-oleyl phosphatidylcholine/palmitoyl-oleyl phosphatidylserine (POPC-POPS. Analysis of the results suggested that residues F222 and T235 may contribute to the ligand-receptor recognition. Accordingly, alanine mutants at positions 222 and 235 were constructed, expressed, and their binding properties determined. The results confirmed the role of these residues in modulating the binding affinity of the ligand.

  13. [2 fatal cases of acute myeloid leukemia (M3, M4) during pregnancy].

    Science.gov (United States)

    Aragona, M; Asmundo, A

    1995-04-01

    Two cases of unexpected post-partum death of women with acute leukemia are described. In the first case (1st pregnancy) the diagnosis (acute promyelocytic leukemia: M3) was performed one week before delivery and death occurred 3 days later, because of hemorrhagic and renal DIC complication. Since one month before hospitalization, laboratory exams indicated a serious hematological pathology and no further exams were carried out by the physicians, elements of professional fault were recognized in them, considering that because of the diagnostic omission it was impossible to make an early diagnosis and thus perform to specific therapy, adopted only in the terminal phase. This specific therapy is able to determine remission from most cases of acute promyelocytic leukemia. In the second case (2nd pregnancy) the diagnosis (acute myelomonocytic leukemia: M4) was performed only postmortem because, during the whole pregnancy, no signs of disease were evident. After a few hours from the spontaneous delivery, death occurred as a result of an intractable + hemorrhagic syndrome caused by primary hyperfibrinolysis and repeated episodes of cardiac arrest, without possibility of recognizing it. The medical procedures for this case, both throughout pregnancy and terminal phases, appeared free of censure.

  14. Experimental Study of Ultralight (<300 kg/m3 Foamed Concrete

    Directory of Open Access Journals (Sweden)

    Xianjun Tan

    2014-01-01

    Full Text Available A type of ultralight (<300 kg/m3 foamed concrete (FC, which can be used as a new energy-conservation and environmental-protection building material and is particularly suitable for the thermal-insulation engineering of building external walls, was produced. The influences of different mixing amounts of fly ash, fly ash activator, WC (WC ratio, and foaming agent (FA on the compressive strength of FC were reported. The experimental study indicated that (1 the addition of fly ash reduced the strength of the FC and that the appropriate mixing amount of fly ash in this ultralight FC system should not exceed 45%; (2 with the increasing of fly ash activator, the strength of the FC sample is notably enhanced and the appropriate mixing amount of fly ash activator is 2.5%; (3 the optimized proportion of WC ratio is 0.45, and the FC that was produced according to this proportion has relatively high compressive strength; (4 by increasing the mixing amount of FA, the compressive strength of the FC notably decreases, and the optimal mixing amount of FA in this experiment is 3.5%.

  15. GRAVITAS : General Relativistic Astrophysics VIa Timing And Spectroscopy: An ESA M3 mission proposal

    CERN Document Server

    Nandra, Kirpal; Fabian, Andy; Strueder, Lothar; Willingale, Richard; Watson, Mike; Jonker, Peter; Kunieda, Hideyo; Miniutti, Giovanni; Motch, Christian; Predehl, Peter

    2011-01-01

    GRAVITAS is an X-ray observatory, designed and optimised to address the ESA Cosmic Vision theme of "Matter under extreme conditions". It was submitted as a response to the call for M3 mission proposals. The concept centres around an X-ray telescope of unprecedented effective area, which will focus radiation emitted from close to the event horizon of black holes or the surface of neutron stars. To reveal the nature and behaviour of matter in the most extreme astrophysical environments, GRAVITAS targets a key feature in the X-ray spectra of compact objects: the iron Kalpha line at ~6.5 keV. The energy, profile, and variability of this emission line, and the properties of the surrounding continuum emission, shaped by General Relativity (GR) effects, provide a unique probe of gravity in its strong field limit. Among its prime targets are hundreds of supermassive black holes in bright Active Galactic Nuclei (AGN), which form the perfect laboratory to help understand the physical processes behind black hole growth....

  16. Overtone and multi-mode RR Lyrae stars in the globular cluster M3

    CERN Document Server

    Jurcsik, J; Hajdu, G; Sódor, Á; Nuspl, J; Kolenberg, K; Fűrész, G; Moór, A; Kun, E; Pál, A; Bakos, J; Kelemen, J; Kovács, T; Kriskovics, L; Sárneczky, K; Szalai, T; Szing, A; Vida, K

    2015-01-01

    The overtone and multi-mode RR Lyrae stars in the globular cluster M3 are studied using a 200-d long, $B,V$ and $I_{\\mathrm C}$ time-series photometry obtained in 2012. 70\\% of the 52 overtone variables observed show some kind of multi-periodicity (additional frequency at ${f_{0.61}}={f_{\\mathrm {1O}}}/0.61$ frequency ratio, Blazhko effect, double/multi-mode pulsation, period doubling). A signal at 0.587 frequency ratio to the fundamental-mode frequency is detected in the double-mode star, V13, which may be identified as the second radial overtone mode. If this mode-identification is correct, than V13 is the first RR Lyrae star showing triple-mode pulsation of the first three radial modes. Either the Blazhko effect or the ${f_{0.61}}$ frequency (or both of these phenomena) appear in 7 double-mode stars. The $P_{\\mathrm{1O}}/P_{\\mathrm{F}}$ period ratio of RRd stars showing the Blazhko effect are anomalous. A displacement of the main frequency component at the fundamental-mode with the value of modulation freq...

  17. IFR safety tests M2 and M3 in TREAT: data and analysis

    Energy Technology Data Exchange (ETDEWEB)

    Robinson, W R; Lo, R K; Bauer, T H; Froehle, P H; Helenberg, H W; Morman, J A; Stanford, G S; Wright, A E

    1985-06-01

    TREAT tests M2 and M3 were performed to obtain information on the characteristics of metal-alloy reactor fuel under slow transient overpower accident conditions, in particular, the margin to cladding breach and the axial self-extrusion of fuel within intact cladding. The tests used U-5Fs fuel pins irradiated to burnup levels of 0.3 at. %, 4.5 at. % and 7.9 at. %. Each pin was located in a separte flowtube and cooled by flowing sodium. In one test, a pin of each burnup was heated to incipient cladding breach. In the other, pins of the medium and high burnup levels wer heated to slightly beyond breach. Pre- and post-failure fuel motions were monitored by the fast-neutron hodoscope. The time and axial location of cladding breach were determined from the test-loop instrumentation. Computations of fuel extrusion and cladding failure are desribed. The models used in the computations include effects of retained fission gas expansion, vaporization of the sodium-bond annulus in low burnup fuel, and cladding-wall thinning by eutectic formation.

  18. Spectral radius of graphs

    CERN Document Server

    Stevanovic, Dragan

    2015-01-01

    Spectral Radius of Graphs provides a thorough overview of important results on the spectral radius of adjacency matrix of graphs that have appeared in the literature in the preceding ten years, most of them with proofs, and including some previously unpublished results of the author. The primer begins with a brief classical review, in order to provide the reader with a foundation for the subsequent chapters. Topics covered include spectral decomposition, the Perron-Frobenius theorem, the Rayleigh quotient, the Weyl inequalities, and the Interlacing theorem. From this introduction, the

  19. Comparison of human and porcine gastric clasp and sling fiber contraction by M2 and M3 muscarinic receptors.

    Science.gov (United States)

    Vegesna, Anil K; Braverman, Alan S; Miller, Larry S; Tallarida, Ronald J; Tiwana, Mansoor I; Khayyam, Umar; Ruggieri, Michael R

    2010-04-01

    To compare the gastroesophageal junction of the human with the pig, M(2) and M(3) receptor densities and the potencies of M(2) and M(3) muscarinic receptor subtype selective antagonists were determined in gastric clasp and sling smooth muscle fibers. Total muscarinic and M(2) receptors are higher in pig than human clasp and sling fibers. M(3) receptors are higher in human compared with pig sling fibers but lower in human compared with pig clasp fibers. Clasp fibers have fewer M(3) receptors than sling fibers in both humans and pigs. Similar to human clasp fibers, pig clasp fibers contract significantly less than pig sling fibers. Analysis of the methoctramine Schild plot suggests that M(2) receptors are involved in mediating contraction in pig clasp and sling fibers. Darifenacin potency suggests that M(3) receptors mediate contraction in pig sling fibers and that M(2) and M(3) receptors mediate contraction in pig clasp fibers. Taken together, the data suggest that both M(2) and M(3) muscarinic receptors mediate the contraction in both pig clasp and sling fibers similar to human clasp and sling fibers.

  20. Unmixing of spectrally similar minerals

    CSIR Research Space (South Africa)

    Debba, Pravesh

    2009-01-01

    Full Text Available -bearing oxide/hydroxide/sulfate minerals in complex mixtures be obtained using hyperspectral data? Debba (CSIR) Unmixing of spectrally similar minerals MERAKA 2009 3 / 18 Method of spectral unmixing Old method: problem Linear Spectral Mixture Analysis (LSMA...

  1. The JCMT Spectral Legacy Survey

    CERN Document Server

    Plume, R; Helmich, F; Van der Tak, F F S; Roberts, H; Bowey, J; Buckle, J; Butner, H; Caux, E; Ceccarelli, C; Van Dishoeck, E F; Friberg, P; Gibb, A G; Hatchell, J; Hogerheijde, M R; Matthews, H; Millar, T; Mitchell, G; Moore, T J T; Ossenkopf, V; Rawlings, J; Richer, J; Roellig, M; Schilke, P; Spaans, M; Tielens, A G G M; Thompson, M A; Viti, S; Weferling, B; White, G J; Wouterloot, J; Yates, J; Zhu, M; White, Glenn J.

    2006-01-01

    Stars form in the densest, coldest, most quiescent regions of molecular clouds. Molecules provide the only probes which can reveal the dynamics, physics, chemistry and evolution of these regions, but our understanding of the molecular inventory of sources and how this is related to their physical state and evolution is rudimentary and incomplete. The Spectral Legacy Survey (SLS) is one of seven surveys recently approved by the JCMT Board. Starting in 2007, the SLS will produce a spectral imaging survey of the content and distribution of all the molecules detected in the 345 GHz atmospheric window (between 332 GHz and 373 GHz) towards a sample of 5 sources. Our intended targets are: a low mass core (NGC1333 IRAS4), 3 high mass cores spanning a range of star forming environments and evolutionary states (W49, AFGL2591, and IRAS20126), and a PDR (the Orion Bar). The SLS will use the unique spectral imaging capabilities of HARP-B/ACSIS to study the molecular inventory and the physical structure of these objects, w...

  2. Vowel Inherent Spectral Change

    CERN Document Server

    Assmann, Peter

    2013-01-01

    It has been traditional in phonetic research to characterize monophthongs using a set of static formant frequencies, i.e., formant frequencies taken from a single time-point in the vowel or averaged over the time-course of the vowel. However, over the last twenty years a growing body of research has demonstrated that, at least for a number of dialects of North American English, vowels which are traditionally described as monophthongs often have substantial spectral change. Vowel Inherent Spectral Change has been observed in speakers’ productions, and has also been found to have a substantial effect on listeners’ perception. In terms of acoustics, the traditional categorical distinction between monophthongs and diphthongs can be replaced by a gradient description of dynamic spectral patterns. This book includes chapters addressing various aspects of vowel inherent spectral change (VISC), including theoretical and experimental studies of the perceptually relevant aspects of VISC, the relationship between ar...

  3. Temporal Lorentzian spectral triples

    Science.gov (United States)

    Franco, Nicolas

    2014-09-01

    We present the notion of temporal Lorentzian spectral triple which is an extension of the notion of pseudo-Riemannian spectral triple with a way to ensure that the signature of the metric is Lorentzian. A temporal Lorentzian spectral triple corresponds to a specific 3 + 1 decomposition of a possibly noncommutative Lorentzian space. This structure introduces a notion of global time in noncommutative geometry. As an example, we construct a temporal Lorentzian spectral triple over a Moyal-Minkowski spacetime. We show that, when time is commutative, the algebra can be extended to unbounded elements. Using such an extension, it is possible to define a Lorentzian distance formula between pure states with a well-defined noncommutative formulation.

  4. Spectral recognition of graphs

    Directory of Open Access Journals (Sweden)

    Cvetković Dragoš

    2012-01-01

    Full Text Available At some time, in the childhood of spectral graph theory, it was conjectured that non-isomorphic graphs have different spectra, i.e. that graphs are characterized by their spectra. Very quickly this conjecture was refuted and numerous examples and families of non-isomorphic graphs with the same spectrum (cospectral graphs were found. Still some graphs are characterized by their spectra and several mathematical papers are devoted to this topic. In applications to computer sciences, spectral graph theory is considered as very strong. The benefit of using graph spectra in treating graphs is that eigenvalues and eigenvectors of several graph matrices can be quickly computed. Spectral graph parameters contain a lot of information on the graph structure (both global and local including some information on graph parameters that, in general, are computed by exponential algorithms. Moreover, in some applications in data mining, graph spectra are used to encode graphs themselves. The Euclidean distance between the eigenvalue sequences of two graphs on the same number of vertices is called the spectral distance of graphs. Some other spectral distances (also based on various graph matrices have been considered as well. Two graphs are considered as similar if their spectral distance is small. If two graphs are at zero distance, they are cospectral. In this sense, cospectral graphs are similar. Other spectrally based measures of similarity between networks (not necessarily having the same number of vertices have been used in Internet topology analysis, and in other areas. The notion of spectral distance enables the design of various meta-heuristic (e.g., tabu search, variable neighbourhood search algorithms for constructing graphs with a given spectrum (spectral graph reconstruction. Several spectrally based pattern recognition problems appear in many areas (e.g., image segmentation in computer vision, alignment of protein-protein interaction networks in bio

  5. Signal transduction by M3 muscarinic acetylcholine receptor in prostate cancer

    Science.gov (United States)

    GUO, LIQIANG; LIU, YUQIANG; DING, ZHIBO; SUN, WENDONG; YUAN, MINGZHEN

    2016-01-01

    The present study aimed to investigate the potential mechanisms used during signal transduction by M3 muscarinic acetylcholine receptor (CHRM3) in prostate cancer. The microarray datasets of GSE3325, including 5 clinically localized primary prostate cancers and 4 benign prostate tissues, were downloaded from the Gene Expression Omnibus database. The differentially-expressed genes (DEGs) in primary prostate cancer tissues compared with benign controls were screened using the Limma package. Gene Ontology and pathway enrichment analyses were performed using the Database for Annotation Visualization and Integrated Discovery. Next, a protein-protein interaction (PPI) network was constructed. Additionally, microRNAs (miRNAs) associated with DEGs were predicted and miRNA-target DEG analysis was performed using a Web-based Gene Set Analysis Toolkit. Finally, the PPI network and the miRNA-target DEG network were integrated using Cytoscape. In total, 224 DEGs were screened in the prostate cancer tissues, including 113 upregulated and 111 downregulated genes. CHRM3 and epidermal growth factor (EGF) were enriched in the regulation of the actin cytoskeleton. EGF and v-myc avian myelocytomatosis viral oncogene homolog (Myc) were enriched in the mitogen-activated protein kinase (MAPK) signaling pathway. EGF with the highest degree of connectivity was the hub node in the PPI network, and miR-34b could interact with Myc directly in the miRNA-target DEG network. EGF and Myc may exhibit significant roles in the progression of prostate cancer via regulation of the actin cytoskeleton and the MAPK signaling pathway. CHRM3 may activate these two pathways in prostate cancer progression. Thus, these two key factors and pathways may be crucial mechanisms during signal transduction by CHRM3 in prostate cancer. PMID:26870222

  6. Simulation of VANAM M3 test using MELCOR 1.8.3

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Sung Won; Kim, Hee Dong [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1996-07-01

    A standard problem is defined as a comparison between experimental and analytical results in the field of reactor safety research. The detailed comparison of the data permits conclusions for the reliability and precision of computer simulations of postulated accidents and contributions to the development and improvement of reactor safety computer codes. Following a suggestion of the Federal Republic of Germany, the OECD-CSNI agreed to offer the experiment VANAM M3 at the Battelle Model Containment (BMC), an experiment on thermohydraulics and aerosol behavior in a containment, as International Standard Problem No. 37 (ISP 37). The general objectives of the ISP 37 are to analyse the thermohydraulics of a containment atmosphere and the distribution and settlement of aerosol after a high pressure path with depressurization by pressurizer relief valve discharge. Steam condensation at the aerosol particles(condensation in volume) is enhanced by the hygroscopic properties of the aerosol materials, even in case of limited steam supply. The originally small, low-density NaOH particles are converted to solution droplets by steam condensation, the increasing droplet mass significantly enhancing aerosol depletion by gravity settlement. As a result, higher depletion rate have been obtained for the NaOH aerosol than for the SnO{sub 2} aerosol in M2. The MELCOR code, version 1.8.3, has been used for the simulation of this experiment, and the results are compared with the results of other calculations at GRS. The objectives of this report are to contribute to the efficient use of MELCOR code and understanding of the aerosol behavior. 12 tabs., 19 figs., 11 refs. (Author).

  7. Agronomic Characterization of Wheat Mutants (Triticum aestivum of M3 Generation Planted in Sukabumi

    Directory of Open Access Journals (Sweden)

    Laela Sari

    2016-11-01

    Full Text Available The purpose of this study was to identify the selection criteria to obtain a superior mutant derived from the wheat plants of such varieties as Dewata, Selayar and Alibey, adaptive in medium land. The analysis of agronomic growth characters showed a significantly effect on a growth percentage of the initial growth (8 mutants, flowering time (1 mutant, panicle stem length (15 mutants, number of panicles (7 mutants, the number of grains per panicle (8 mutants, grain weight observed (8 mutants, grain weight per genotype (6 mutants, leaf area (2 mutants and leaf greenness (5 mutants. The effects on the characters of ripe time, harvest, panicle length and plant height were not significant. The mutants of Dewata, Selayar and Alibey could be selected based on the characters of panicle stem length, number of grains per panicle and grain weight per observation because these characters generated more mutants than the other characters. The correlation analysis between the characters of growth and yield components of wheat mutants showed that the number of grains per panicle was positively correlated with the grain weight observed, while the length of panicle stem was positively correlated with grain weight per genotype, number of panicles and leaf area. Hopefully some mutants produced could adapt to the tropical medium land, thus adding to the diversity of wheat germplasm in Indonesia, thereby reducing the import of wheat to Indonesia.How to CiteSari, L., Purwito, A., Sopandie, D., Purnamaningsih, R. & Sudarmonowati, E. (2016. Agronomic Characterization of Wheat Mutants (Triticum aestivum of M3 Generation Planted in Sukabumi. Biosaintifika: Journal of Biology & Biology Education, 8(3, 353-361. 

  8. Spectrally selective glazings

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-08-01

    Spectrally selective glazing is window glass that permits some portions of the solar spectrum to enter a building while blocking others. This high-performance glazing admits as much daylight as possible while preventing transmission of as much solar heat as possible. By controlling solar heat gains in summer, preventing loss of interior heat in winter, and allowing occupants to reduce electric lighting use by making maximum use of daylight, spectrally selective glazing significantly reduces building energy consumption and peak demand. Because new spectrally selective glazings can have a virtually clear appearance, they admit more daylight and permit much brighter, more open views to the outside while still providing the solar control of the dark, reflective energy-efficient glass of the past. This Federal Technology Alert provides detailed information and procedures for Federal energy managers to consider spectrally selective glazings. The principle of spectrally selective glazings is explained. Benefits related to energy efficiency and other architectural criteria are delineated. Guidelines are provided for appropriate application of spectrally selective glazing, and step-by-step instructions are given for estimating energy savings. Case studies are also presented to illustrate actual costs and energy savings. Current manufacturers, technology users, and references for further reading are included for users who have questions not fully addressed here.

  9. Thermophotovoltaic Spectral Control

    Energy Technology Data Exchange (ETDEWEB)

    DM DePoy; PM Fourspring; PF Baldasaro; JF Beausang; EJ Brown; MW Dashiel; KD Rahner; TD Rahmlow; JE Lazo-Wasem; EJ Gratrix; B Wemsman

    2004-06-09

    Spectral control is a key technology for thermophotovoltaic (TPV) direct energy conversion systems because only a fraction (typically less than 25%) of the incident thermal radiation has energy exceeding the diode bandgap energy, E{sub g}, and can thus be converted to electricity. The goal for TPV spectral control in most applications is twofold: (1) Maximize TPV efficiency by minimizing transfer of low energy, below bandgap photons from the radiator to the TPV diode. (2) Maximize TPV surface power density by maximizing transfer of high energy, above bandgap photons from the radiator to the TPV diode. TPV spectral control options include: front surface filters (e.g. interference filters, plasma filters, interference/plasma tandem filters, and frequency selective surfaces), back surface reflectors, and wavelength selective radiators. System analysis shows that spectral performance dominates diode performance in any practical TPV system, and that low bandgap diodes enable both higher efficiency and power density when spectral control limitations are considered. Lockheed Martin has focused its efforts on front surface tandem filters which have achieved spectral efficiencies of {approx}83% for E{sub g} = 0.52 eV and {approx}76% for E{sub g} = 0.60 eV for a 950 C radiator temperature.

  10. Truthful approximations to range voting

    DEFF Research Database (Denmark)

    Filos-Ratsika, Aris; Miltersen, Peter Bro

    We consider the fundamental mechanism design problem of approximate social welfare maximization under general cardinal preferences on a finite number of alternatives and without money. The well-known range voting scheme can be thought of as a non-truthful mechanism for exact social welfare...... maximization in this setting. With m being the number of alternatives, we exhibit a randomized truthful-in-expectation ordinal mechanism implementing an outcome whose expected social welfare is at least an Omega(m^{-3/4}) fraction of the social welfare of the socially optimal alternative. On the other hand, we...... show that for sufficiently many agents and any truthful-in-expectation ordinal mechanism, there is a valuation profile where the mechanism achieves at most an O(m^{-{2/3}) fraction of the optimal social welfare in expectation. We get tighter bounds for the natural special case of m = 3...

  11. Spectral polarimetric light-scattering by particulate media: 1. Theory of spectral Vector Radiative Transfer

    Science.gov (United States)

    Ceolato, Romain; Riviere, Nicolas

    2016-07-01

    Spectral polarimetric light-scattering by particulate media has recently attracted growing interests for various applications due to the production of directional broadband light sources. Here the spectral polarimetric light-scattering signatures of particulate media are simulated using a numerical model based on the spectral Vector Radiative Transfer Equation (VRTE). A microphysical analysis is conducted to understand the dependence of the light-scattering signatures upon the microphysical parameters of particles. We reveal that depolarization from multiple scattering results in remarkable spectral and directional features, which are simulated by our model over a wide spectral range from visible to near-infrared. We propose to use these features to improve the inversion of the scattering problem in the fields of remote sensing, astrophysics, material science, or biomedical.

  12. Rapid spectral analysis for spectral imaging.

    Science.gov (United States)

    Jacques, Steven L; Samatham, Ravikant; Choudhury, Niloy

    2010-07-15

    Spectral imaging requires rapid analysis of spectra associated with each pixel. A rapid algorithm has been developed that uses iterative matrix inversions to solve for the absorption spectra of a tissue using a lookup table for photon pathlength based on numerical simulations. The algorithm uses tissue water content as an internal standard to specify the strength of optical scattering. An experimental example is presented on the spectroscopy of portwine stain lesions. When implemented in MATLAB, the method is ~100-fold faster than using fminsearch().

  13. Peculiarities of lens and tail regeneration detected in newts after spaceflight aboard Foton M3

    Science.gov (United States)

    Grigoryan, Eleonora N.; Almeida, Eduardo; Poplinskaya, Valentina; Novikova, Julia; Domaratskaya, Elena; Aleinikova, Karina; Souza, Kenneth; Skidmore, Mike; Grigoryan, Eleonora N.

    In September 2007 the joint, 12 day long experiment was carried out aboard Russian satellite Foton M3. The goal of the experiment was to study eye lens, tail and forelimb toe regeneration in adult 16 newts (Pl. waltl.) operated 10 days before taking-off. In spaceflight and synchronous ground control we used video recording, temperature and irradiation control, as well as constant availability of thymidine analog BrdU for its absorption via animals' skin. New techniques allowed us to analyze animals' behavior in hyperand microgravity periods of time, to take proper account of spaceflight factors, and measure accumulated pools of DNA-synthesizing cells in regenerating tissues. All tissue specimens obtained from animals were isolated in the day of landing and then prepared for morphological, immunochemical and molecular investigations. Synchronous control was shifted for two days and reproduced flight conditions except changes of gravity influence. As a result in flown animals as compared with synchronous ground control we found lens regeneration of 0.5-1 stage speeded up and an increased BrdU+ (S-phase) cell number in eye cornea, growth zone, limbus and newly forming lens. These features of regeneration were accompanied by an increase of FGF2 expression in eye growth zone and heat shock protein (HSP90) induction purely in retinal macroglial cells of regenerating eyes. Toe regeneration rate was equal and achieved the stage of accomplished healing of amputation area in both groups - "flown" and control animals. We found no essential differences in tail regeneration rate and tail regenerate sizes in the newts exposed to space and on ground. In both groups tail regeneration reached the stage IV-V when tail length and square were around 4.4 mm and 15.5 mm2, correspondingly. However we did observe remarkable changes of tail regenerate form and some of pigmentation. Computer morphometrical analysis showed that only in ground control animals the evident dorso

  14. Bipolar spectral associative memories.

    Science.gov (United States)

    Spencer, R G

    2001-01-01

    Nonlinear spectral associative memories are proposed as quantized frequency domain formulations of nonlinear, recurrent associative memories in which volatile network attractors are instantiated by attractor waves. In contrast to conventional associative memories, attractors encoded in the frequency domain by convolution may be viewed as volatile online inputs, rather than nonvolatile, off-line parameters. Spectral memories hold several advantages over conventional associative memories, including decoder/attractor separability and linear scalability, which make them especially well suited for digital communications. Bit patterns may be transmitted over a noisy channel in a spectral attractor and recovered at the receiver by recurrent, spectral decoding. Massive nonlocal connectivity is realized virtually, maintaining high symbol-to-bit ratios while scaling linearly with pattern dimension. For n-bit patterns, autoassociative memories achieve the highest noise immunity, whereas heteroassociative memories offer the added flexibility of achieving various code rates, or degrees of extrinsic redundancy. Due to linear scalability, high noise immunity and use of conventional building blocks, spectral associative memories hold much promise for achieving robust communication systems. Simulations are provided showing bit error rates for various degrees of decoding time, computational oversampling, and signal-to-noise ratio.

  15. Noncomputable Spectral Sets

    CERN Document Server

    Teutsch, J

    2007-01-01

    It is possible to enumerate all computer programs. In particular, for every partial computable function, there is a shortest program which computes that function. f-MIN is the set of indices for shortest programs. In 1972, Meyer showed that f-MIN is Turing equivalent to 0'', the halting set with halting set oracle. This paper generalizes the notion of shortest programs, and we use various measures from computability theory to describe the complexity of the resulting "spectral sets." We show that under certain Godel numberings, the spectral sets are exactly the canonical sets 0', 0'', 0''', ... up to Turing equivalence. This is probably not true in general, however we show that spectral sets always contain some useful information. We show that immunity, or "thinness" is a useful characteristic for distinguishing between spectral sets. In the final chapter, we construct a set which neither contains nor is disjoint from any infinite arithmetic set, yet it is 0-majorized and contains a natural spectral set. Thus ...

  16. Preliminary evaluation of vector flow and spectral velocity estimation

    DEFF Research Database (Denmark)

    Pedersen, Mads Møller; Pihl, Michael Johannes; Haugaard, Per

    Spectral estimation is considered as the golden standard in ultrasound velocity estimation. For spectral velocity estimation the blood flow angle is set by the ultrasound operator. Vector flow provides temporal and spatial estimates of the blood flow angle and velocity. A comparison of vector flow...... agrees with the spectral flow angle. The vector velocity estimates agrees with the spectral estimates at PS and ED. From preliminary data it is concluded that vector flow angle estimation can replace the operator-dependent angle correction used for spectral velocity estimation....... estimation and spectral estimates is presented. The variation of the blood flow angle and the effect on the velocity estimate is investigated. The right common carotid arteries of three healthy volunteers were scanned. Real-time spectral and vector flow data were obtained simultaneously from one range gate...

  17. Some remarks on the level of helium enhancement among M3's horizontal-branch stars

    CERN Document Server

    Valcarce, A A R; Alonso-García, J; Ramos, R Contreras; Alves, S

    2016-01-01

    (Abridged) The color and luminosity distribution of horizontal branch (HB) stars in globular clusters are sensitive probes of their original helium abundances. However, recent analyses based on visual and near-ultraviolet (UV) CMDs have provided conflicting results. To clarify the situation, we address the optimum ranges of applicability (in terms of the $T_{eff}$ range covered by the HB stars) for visual and near-UV CMDs, as far as application of this HB $Y$ test goes. We consider both Stromgren and Hubble Space Telescope (HST) bandpasses. Our results indicate that the distributions of HB stars in the y vs (b-y) plane can be a reliable indicator of the He content in cool blue HB (BHB) stars, particularly when a differential comparison between blue and red HB stars is carried out in the range $T_{eff}<8300$K. Conversely, we demonstrate that CMDs using the F336W filter have a much less straightforward interpretation at the cool end of the BHB, as the distributions of HB stars in the F336W vs (F336W-F555W) p...

  18. SAP is required for the development of innate phenotype in H2-M3-restricted CD8+ T cells1

    Science.gov (United States)

    Bediako, Yaw; Bian, Yao; Zhang, Hong; Cho, Hoonsik; Stein, Paul L.; Wang, Chyung-Ru

    2012-01-01

    H2-M3-restricted T cells have a pre-activated surface phenotype, rapidly expand and produce cytokines upon stimulation and as such, are classified as innate T cells. Unlike most innate T cells, M3-restricted T cells also express CD8αβ co-receptors and a diverse TCR repertoire: hallmarks of conventional MHC Ia-restricted CD8+ T cells. Although iNKT cells are also innate lymphocytes, they are selected exclusively on hematopoietic cells (HC), while M3-restricted T cells can be selected on either hematopoietic or thymic epithelial cells (TEC). Moreover, their phenotypes differ depending on what cells mediate their selection. Though there is a clear correlation between selection on HC and development of innate phenotype, the underlying mechanism remains unclear. SAP is required for the development of iNKT cells and mediates signals from SLAM receptors that are exclusively expressed on HC. Based on their dual selection pathway, M3-restricted T cells present a unique model for studying the development of innate T cell phenotype. Using both polyclonal and transgenic mouse models we demonstrate that while M3-restricted T cells are capable of developing in the absence of SAP, SAP is required for HC-mediated selection, development of pre-activated phenotype and heightened effector functions of M3-restricted T cells. These findings are significant because they directly demonstrate the need for SAP in HC-mediated acquisition of innate T cell phenotype and suggest that due to their SAP-dependent HC-mediated selection, M3-restricted T cells develop a pre-activated phenotype and an intrinsic ability to proliferate faster upon stimulation, allowing for an important role in the early response to infection. PMID:23041566

  19. Parametric Explosion Spectral Model

    Energy Technology Data Exchange (ETDEWEB)

    Ford, S R; Walter, W R

    2012-01-19

    Small underground nuclear explosions need to be confidently detected, identified, and characterized in regions of the world where they have never before occurred. We develop a parametric model of the nuclear explosion seismic source spectrum derived from regional phases that is compatible with earthquake-based geometrical spreading and attenuation. Earthquake spectra are fit with a generalized version of the Brune spectrum, which is a three-parameter model that describes the long-period level, corner-frequency, and spectral slope at high-frequencies. Explosion spectra can be fit with similar spectral models whose parameters are then correlated with near-source geology and containment conditions. We observe a correlation of high gas-porosity (low-strength) with increased spectral slope. The relationship between the parametric equations and the geologic and containment conditions will assist in our physical understanding of the nuclear explosion source.

  20. Photovoltaic spectral responsivity measurements

    Energy Technology Data Exchange (ETDEWEB)

    Emery, K.; Dunlavy, D.; Field, H.; Moriarty, T. [National Renewable Energy Lab., Golden, CO (United States)

    1998-09-01

    This paper discusses the various elemental random and nonrandom error sources in typical spectral responsivity measurement systems. The authors focus specifically on the filter and grating monochrometer-based spectral responsivity measurement systems used by the Photovoltaic (PV) performance characterization team at NREL. A variety of subtle measurement errors can occur that arise from a finite photo-current response time, bandwidth of the monochromatic light, waveform of the monochromatic light, and spatial uniformity of the monochromatic and bias lights; the errors depend on the light source, PV technology, and measurement system. The quantum efficiency can be a function of he voltage bias, light bias level, and, for some structures, the spectral content of the bias light or location on the PV device. This paper compares the advantages and problems associated with semiconductor-detector-based calibrations and pyroelectric-detector-based calibrations. Different current-to-voltage conversion and ac photo-current detection strategies employed at NREL are compared and contrasted.

  1. Spectral Networks and Snakes

    CERN Document Server

    Gaiotto, Davide; Neitzke, Andrew

    2012-01-01

    We apply and illustrate the techniques of spectral networks in a large collection of A_{K-1} theories of class S, which we call "lifted A_1 theories." Our construction makes contact with Fock and Goncharov's work on higher Teichmuller theory. In particular we show that the Darboux coordinates on moduli spaces of flat connections which come from certain special spectral networks coincide with the Fock-Goncharov coordinates. We show, moreover, how these techniques can be used to study the BPS spectra of lifted A_1 theories. In particular, we determine the spectrum generators for all the lifts of a simple superconformal field theory.

  2. USGS Digital Spectral Library splib06a

    Science.gov (United States)

    Clark, Roger N.; Swayze, Gregg A.; Wise, Richard A.; Livo, K. Eric; Hoefen, Todd M.; Kokaly, Raymond F.; Sutley, Stephen J.

    2007-01-01

    Introduction We have assembled a digital reflectance spectral library that covers the wavelength range from the ultraviolet to far infrared along with sample documentation. The library includes samples of minerals, rocks, soils, physically constructed as well as mathematically computed mixtures, plants, vegetation communities, microorganisms, and man-made materials. The samples and spectra collected were assembled for the purpose of using spectral features for the remote detection of these and similar materials. Analysis of spectroscopic data from laboratory, aircraft, and spacecraft instrumentation requires a knowledge base. The spectral library discussed here forms a knowledge base for the spectroscopy of minerals and related materials of importance to a variety of research programs being conducted at the U.S. Geological Survey. Much of this library grew out of the need for spectra to support imaging spectroscopy studies of the Earth and planets. Imaging spectrometers, such as the National Aeronautics and Space Administration (NASA) Airborne Visible/Infra Red Imaging Spectrometer (AVIRIS) or the NASA Cassini Visual and Infrared Mapping Spectrometer (VIMS) which is currently orbiting Saturn, have narrow bandwidths in many contiguous spectral channels that permit accurate definition of absorption features in spectra from a variety of materials. Identification of materials from such data requires a comprehensive spectral library of minerals, vegetation, man-made materials, and other subjects in the scene. Our research involves the use of the spectral library to identify the components in a spectrum of an unknown. Therefore, the quality of the library must be very good. However, the quality required in a spectral library to successfully perform an investigation depends on the scientific questions to be answered and the type of algorithms to be used. For example, to map a mineral using imaging spectroscopy and the mapping algorithm of Clark and others (1990a, 2003b

  3. Intruder States and their Local Effect on Spectral Statistics

    CERN Document Server

    Flores, J; Leyvraz, F

    1997-01-01

    The effect on spectral statistics and on the revival probability of intruder states in a random background is analysed numerically and with perturbative methods. For random coupling the intruder does not affect the GOE spectral statistics of the background significantly, while a constant coupling causes very strong correlations at short range with a fourth power dependence of the spectral two-point function at the origin.The revival probability is significantly depressed for constant coupling as compared to random coupling.

  4. Spectral library searching in proteomics.

    Science.gov (United States)

    Griss, Johannes

    2016-03-01

    Spectral library searching has become a mature method to identify tandem mass spectra in proteomics data analysis. This review provides a comprehensive overview of available spectral library search engines and highlights their distinct features. Additionally, resources providing spectral libraries are summarized and tools presented that extend experimental spectral libraries by simulating spectra. Finally, spectrum clustering algorithms are discussed that utilize the same spectrum-to-spectrum matching algorithms as spectral library search engines and allow novel methods to analyse proteomics data.

  5. 1750m3高炉煤气除尘改造及TRT发电技术的应用%De-dusting System Improvement and TRT Technology Application on the 1750m3 Blast Furnaces

    Institute of Scientific and Technical Information of China (English)

    曹海刚; 许强

    2012-01-01

    介绍了济钢2座1750m3高炉煤气湿法改干法涂尘及TRT发电的主体设备、主要技术参数及取得的经济效益。%On the two 1750m3 blast furnaces of Jinan Iron and Steel Co., the wet BFG de-ducting system is replaced with the dry de-dusting system and the TRT generation unit is installed. These equipment and their technical data and economic benefits are presented.

  6. Spectral ladar: towards active 3D multispectral imaging

    Science.gov (United States)

    Powers, Michael A.; Davis, Christopher C.

    2010-04-01

    In this paper we present our Spectral LADAR concept, an augmented implementation of traditional LADAR. This sensor uses a polychromatic source to obtain range-resolved 3D spectral images which are used to identify objects based on combined spatial and spectral features, resolving positions in three dimensions and up to hundreds of meters in distance. We report on a proof-of-concept Spectral LADAR demonstrator that generates spectral point clouds from static scenes. The demonstrator transmits nanosecond supercontinuum pulses generated in a photonic crystal fiber. Currently we use a rapidly tuned receiver with a high-speed InGaAs APD for 25 spectral bands with the future expectation of implementing a linear APD array spectrograph. Each spectral band is independently range resolved with multiple return pulse recognition. This is a critical feature, enabling simultaneous spectral and spatial unmixing of partially obscured objects when not achievable using image fusion of monochromatic LADAR and passive spectral imagers. This enables higher identification confidence in highly cluttered environments such as forested or urban areas (e.g. vehicles behind camouflage or foliage). These environments present challenges for situational awareness and robotic perception which can benefit from the unique attributes of Spectral LADAR. Results from this demonstrator unit are presented for scenes typical of military operations and characterize the operation of the device. The results are discussed here in the context of autonomous vehicle navigation and target recognition.

  7. Horizontal-Branch Models and the Second-Parameter Effect. IV. The Case of M3 and Palomar 3

    CERN Document Server

    Catelan, M; Rood, R T

    2001-01-01

    We present a detailed analysis of the "second-parameter pair" of globular clusters M3 (NGC 5272) and Palomar 3. Our main results can be summarized as follows: i) The horizontal-branch (HB) morphology of M3 is significantly bluer in its inner regions (observed with the Hubble Space Telescope) than in the cluster outskirts (observed from the ground), i.e., M3 has an internal second parameter. Most plausibly the mass loss on the red giant branch (RGB) has been more efficient in the inner than in the outer regions of the cluster. ii) The dispersion in mass of the Pal 3 HB is found to be very small -- consistent with zero -- and we argue that this is unlikely to be due to a statistical fluctuation. It is this small mass dispersion that leads to the most apparent difference in the HB morphologies of M3 and Pal 3. iii) The relative HB types of M3 and Pal 3, as measured by mean colors or parameters involving the number of blue, variable, and red HB stars, can easily be accounted for by a fairly small difference in ag...

  8. Acetylcholine acts through M3 muscarinic receptor to activate the EGFR signaling and promotes gastric cancer cell proliferation

    Science.gov (United States)

    Yu, Huangfei; Xia, Hongwei; Tang, Qiulin; Xu, Huanji; Wei, Guoqing; Chen, Ying; Dai, Xinyu; Gong, Qiyong; Bi, Feng

    2017-01-01

    Acetylcholine (ACh), known as a neurotransmitter, regulates the functions of numerous fundamental central and peripheral nervous system. Recently, emerging evidences indicate that ACh also plays an important role in tumorigenesis. However, little is known about the role of ACh in gastric cancer. Here, we reported that ACh could be auto-synthesized and released from MKN45 and BGC823 gastric cancer cells. Exogenous ACh promoted cell proliferation in a does-dependent manner. The M3R antagonist 4-DAMP, but not M1R antagonist trihexyphenidyl and M2/4 R antagonist AFDX-116, could reverse the ACh-induced cell proliferation. Moreover, ACh, via M3R, activated the EGFR signaling to induce the phosphorylation of ERK1/2 and AKT, and blocking EGFR pathway by specific inhibitor AG1478 suppressed the ACh induced cell proliferation. Furthermore, the M3R antagonist 4-DAMP and darifenacin could markedly inhibit gastric tumor formation in vivo. 4-DAMP could also significantly enhance the cytotoxic activity of 5-Fu against the MKN45 and BGC823 cells, and induce the expression of apoptosis-related proteins such as Bax and Caspase-3. Together, these findings indicated that the autocrine ACh could act through M3R and the EGFR signaling to promote gastric cancer cells proliferation, targeting M3R or EGFR may provide us a potential therapeutic strategy for gastric cancer treatment. PMID:28102288

  9. Genetic environments of the transferable plasmid-mediated blaCTX-M-3 gene in Serratia marcescens isolates.

    Science.gov (United States)

    Chu, Pei-Yu; Peng, Chien-Fang

    2014-01-01

    In this study, genetic environments of the transferable plasmid-mediated blaCTX-M-3 gene were characterized among 14 isolates of cefotaxime-resistant Serratia marcescens using PCR and BLAST DNA sequence analysis. A total of 3 types of genetic architectures in the regions surrounding this blaCTX-M-3 gene were identified. Type I architecture was characterized by the presence of a complete insertion sequence of tnpA-ISEcp1, identified as interrupting a reverse IS26 sequence in the upstream region of the blaCTX-M-3 gene. A reverse-directional orf477 fragment was located downstream of the blaCTX-M-3 gene, which was in the same direction of the mucA gene. A common region containing the orf513 element was located upstream of the mucA gene. Moreover, a copy of the 3'-CS2 element was located immediately upstream of the orf513 element. A novel complex class 1 integron was characterized by the presence of the dfrA19 gene, which was flanked by two copies of class 1 integrons. This is the first report to describe the dfrA19 gene within a novel complex class 1 integron in S. marcescens isolates from Taiwan. This novel complex class 1 integron structure was located distantly upstream of the blaCTX-M-3 gene.

  10. Hypocholesterolemic effects of Kluyveromyces marxianus M3 isolated from Tibetan mushrooms on diet-induced hypercholesterolemia in rat

    Directory of Open Access Journals (Sweden)

    Yuanhong Xie

    2015-06-01

    Full Text Available To investigate the effects of Kluyveromyces marxianus M3 isolated from Tibetan mushrooms on diet-induced hypercholesterolemia in rats, female Wistar rats were fed a high-cholesterol diet (HCD for 28 d to generate hyperlipidemic models. Hyperlipidemic rats were assigned to four groups, which were individually treated with three different dosages of K. marxianus M3+HCD or physiological saline+HCD via oral gavage for 28 d. The total cholesterol (TC, triglycerides (TG, high-density lipoprotein cholesterol (HDL-C, and low-density lipoprotein cholesterol (LDL-C levels in the serum and liver of the rats were measured using commercially available enzyme kits. In addition, the liver morphology was also examined using hematoxylin and eosin staining and optical microscopy. According to our results, the serum and liver TC, TG, LDL-C levels and atherogenic index (AI were significantly decreased in rats orally administered K. marxianus M3 (p <0.01, and the HDL-C levels and anti atherogenic index (AAI were significantly increased (p <0.01 compared to the control group. Moreover, K. marxianus M3 treatment also reduced the build-up of lipid droplets in the liver and exhibited normal hepatocytes, suggesting a protective effect of K. marxianus M3 in hyperlipidemic rats.

  11. Hypocholesterolemic effects of Kluyveromyces marxianus M3 isolated from Tibetan mushrooms on diet-induced hypercholesterolemia in rat.

    Science.gov (United States)

    Xie, Yuanhong; Zhang, Hongxing; Liu, Hui; Xiong, Lixia; Gao, Xiuzhi; Jia, Hui; Lian, Zhengxing; Tong, Nengsheng; Han, Tao

    2015-06-01

    To investigate the effects of Kluyveromyces marxianus M3 isolated from Tibetan mushrooms on diet-induced hypercholesterolemia in rats, female Wistar rats were fed a high-cholesterol diet (HCD) for 28 d to generate hyperlipidemic models. Hyperlipidemic rats were assigned to four groups, which were individually treated with three different dosages of K. marxianus M3+HCD or physiological saline+HCD via oral gavage for 28 d. The total cholesterol (TC), triglycerides (TG), high-density lipoprotein cholesterol (HDL-C), and low-density lipoprotein cholesterol (LDL-C) levels in the serum and liver of the rats were measured using commercially available enzyme kits. In addition, the liver morphology was also examined using hematoxylin and eosin staining and optical microscopy. According to our results, the serum and liver TC, TG, LDL-C levels and atherogenic index (AI) were significantly decreased in rats orally administered K. marxianus M3 (p <0.01), and the HDL-C levels and anti atherogenic index (AAI) were significantly increased (p <0.01) compared to the control group. Moreover, K. marxianus M3 treatment also reduced the build-up of lipid droplets in the liver and exhibited normal hepatocytes, suggesting a protective effect of K. marxianus M3 in hyperlipidemic rats.

  12. Spectral statistics of random geometric graphs

    CERN Document Server

    Dettmann, Carl P; Knight, Georgie

    2016-01-01

    We study the spectrum of random geometric graphs using random matrix theory. We look at short range correlations in the level spacings via the nearest neighbour and next nearest neighbour spacing distribution and long range correlations via the spectral rigidity $\\Delta_3$ statistic. These correlations in the level spacings give information about localisation of eigenvectors, level of community structure and the level of randomness within the networks. We find that the spectral statistics of random geometric graphs fits the universality of random matrix theory. In particular, the short range correlations are very close to those found in the Gaussian orthogonal ensemble of random matrix theory. For long range correlations we find deviations from Gaussian orthogonal ensemble statistics towards Poisson. We compare with previous results for Erd\\H{o}s-R\\'{e}nyi, Barab{\\'a}si-Albert and Watts-Strogatz random graphs where similar random matrix theory universality has been found.

  13. EFFECT OF Nb ON THE MICROSTRUCTURE AND PROPERTIES OF SPRAY FORMED M3 HIGH SPEED STEEL%Nb对喷射成形M3型高速钢组织和性能的影响

    Institute of Scientific and Technical Information of China (English)

    于一鹏; 黄进峰; 崔华; 蔡元华; 张济山

    2012-01-01

    为了利用NbC的高硬度和高热稳定性,并避免其在凝固过程中的过分长大,采用喷射成形快速凝固技术制备了M3型高速钢和以Nb代V的M3型高速钢.利用SEM,EDX和XRD等方法研究了Nb对喷射成形M3型高速钢沉积态组织的影响;利用SRV高温摩擦磨损试验机和三维白光干涉表面形貌仪研究了Nb对喷射成形M3型高速钢摩擦磨损性能的影响.结果表明,用等原子分数的Nb替代V,可大幅增加沉积态中一次MC型碳化物,减少一次M2C型碳化物,同时由于喷射成形高冷速的作用,使得MC碳化物尺寸减小,分布更弥散;这些MC型碳化物的存在是M3型高速钢的抗磨粒磨损性能提高的主要原因,但其对抗氧化性能并无贡献,在高载荷时抗氧化剥落磨损能力增加不明显;Nb对提高M3高速钢回火稳定性也有明显的作用.%Spray forming with a short process chains has been proven to be a powerful tool for the production of high-alloyed materials. Niobium, as a strong former for the carbide, will mainly form primary MC carbides, such as NbC, which can be formed via the reaction between Nb and C atoms at the beginning of solidification, and it can act as the inoculants and refine the cast structure of steel which can mainly form primary MC carbides. M3 high speed steel with or without Nb addition were prepared via spray forming. The effect of Nb on the microstructure of spray formed M3 high speed steel was investigated by SEM, EDX and XRD methods; the friction performances of these two steels were studied by SRV high temperature tribometer and 3D white-light interfering profilometer. The results show that the amount of primary MC carbides can increase sharply while the reduction of the amount of primary M2C due to the substitution of 2% Nb for 1% V (mass fraction) in M3 high speed steel. For the high cooling rate during the spray forming, the primary MC carbides can be refined and dispersed. Large number of primary MC carbides

  14. Blue spectral inflation

    CERN Document Server

    Schunck, Franz E

    2008-01-01

    We reconsider the nonlinear second order Abel equation of Stewart and Lyth, which follows from a nonlinear second order slow-roll approximation. We find a new eigenvalue spectrum in the blue regime. Some of the discrete values of the spectral index n_s have consistent fits to the cumulative COBE data as well as to recent ground-base CMB experiments.

  15. Large Spectral Library Problem

    Energy Technology Data Exchange (ETDEWEB)

    Chilton, Lawrence K.; Walsh, Stephen J.

    2008-10-03

    Hyperspectral imaging produces a spectrum or vector at each image pixel. These spectra can be used to identify materials present in the image. In some cases, spectral libraries representing atmospheric chemicals or ground materials are available. The challenge is to determine if any of the library chemicals or materials exist in the hyperspectral image. The number of spectra in these libraries can be very large, far exceeding the number of spectral channels collected in the ¯eld. Suppose an image pixel contains a mixture of p spectra from the library. Is it possible to uniquely identify these p spectra? We address this question in this paper and refer to it as the Large Spectral Library (LSL) problem. We show how to determine if unique identi¯cation is possible for any given library. We also show that if p is small compared to the number of spectral channels, it is very likely that unique identi¯cation is possible. We show that unique identi¯cation becomes less likely as p increases.

  16. Quarkonium Spectral Functions

    Energy Technology Data Exchange (ETDEWEB)

    Mocsy, Agnes [Department of Mathematics and Science, Pratt Institute, Brooklyn, NY 11205 (United States)

    2009-11-01

    In this talk I summarize the progress achieved in recent years on the understanding of quarkonium properties at finite temperature. Theoretical studies from potential models, lattice QCD, and effective field theories are discussed. I also highlight a bridge from spectral functions to experiment.

  17. Spectral representation of fingerprints

    NARCIS (Netherlands)

    Xu, Haiyun; Bazen, Asker M.; Veldhuis, Raymond N.J.; Kevenaar, Tom A.M.; Akkermans, Anton H.M.

    2007-01-01

    Most fingerprint recognition systems are based on the use of a minutiae set, which is an unordered collection of minutiae locations and directions suffering from various deformations such as translation, rotation and scaling. The spectral minutiae representation introduced in this paper is a novel m

  18. Expression of the M3 Muscarinic Receptor on Orexin Neurons that Project to the Rostral Ventrolateral Medulla.

    Science.gov (United States)

    Dai, Yu-Wen E; Lee, Yen-Hsien; Chen, Jennifer Y S; Lin, Yen-Kuang; Hwang, Ling-Ling

    2016-05-01

    Activation of central cholinergic receptors causes a pressor response in rats, and the hypothalamus is important for this response. Projections from hypothalamic orexin neurons to the rostral ventrolateral medulla (RVLM) are involved in sympatho-excitation of the cardiovascular system. A small population of orexin neurons is regulated by cholinergic inputs through M3 muscarinic acetylcholine receptor (M3 R). To elucidate whether the M3 R on orexin neurons is involved in cardiosympathetic regulation through the RVLM, we examined the presence of the M3 R on retrograde-labeled RVLM-projecting orexin neurons. The retrograde tracer was unilaterally injected into the RVLM. Within the hypothalamus, retrograde-labeled neurons were located predominantly ipsilateral to the injection side. In the anterior hypothalamus (-1.5 to -2.3 mm to the bregma), retrograde-labeled neurons were densely distributed in the paraventricular nuclei and scattered in the retrochiasmatic area. At -2.3 to -3.5 mm from the bregma, labeled neurons were located in the regions where orexin neurons were situated, that is, the tuberal lateral hypothalamic area, perifornical area, and dorsomedial nuclei. Very few retrograde-labeled neurons were observed in the hypothalamus at -3.5 to -4.5 mm from the bregma. About 19.5% ± 1.6% of RVLM-projecting neurons in the tuberal hypothalamus were orexinergic. The M3 R was present on 18.7% ± 3.0% of RVLM-projecting orexin neurons. Injection of a muscarinic agonist, oxotremorine, in the perifornical area resulted in a pressor response, which was attenuated by a pretreatment of atropine. We conclude that cholinergic inputs to orexin neurons may be involved in cardiosympathetic regulation through the M3 R on the orexin neurons that directly project to the RVLM.

  19. Study and Implementation of Floating-point Operations Based on Cortex-M3 Core%Cortex-M3内核浮点型运算的研究与实现

    Institute of Scientific and Technical Information of China (English)

    梅静静; 王申良

    2011-01-01

    通过分析Cortex-M3内核的结构与浮点型格式,充分利用Cortex-M3内核中的分支预测、单周期乘法、硬件除法等众多功能强大的特性,使用Thumb-2指令集实现了单精度浮点型的加、减、乘、除与比较运算,并给出了加减法运算的流程图和除法运算的源程序.%By analyzing the Cortex-M3 core structure and floating-point format, this paper uses the Thumb-2 instruction set to achieve addition, subtraction, multiplication, division and comparison operations of single-precision floating-point numbers, making full use of such powerful features of Cortex-M3 core as branch prediction, single-cycle multiplication and hardware division. The flow chart of addition and subtraction operations, as well as the source program of division operation, is provided.

  20. TREATMENT OF ABNORMAL TEMPERATURE RISE OF 1 800 m3 BF HEARTH%宣钢1800 m3高炉炉缸温度异常升高的处理

    Institute of Scientific and Technical Information of China (English)

    武建新; 匡祎

    2014-01-01

    This paper is aimed at the abnormal temperature rise of the 1800m3 BF hearth carbon bricks . Through correct diagnosis of furnace body corrosion condition , such measures are taken as increasing tita-nium load into the furnace , enhancing cooling intensity , enhancing tap -hole maintenance to guarantee tap-hole depth , changing field on time while tapping and so on , many hidden safety troubles are elimi-nated , and long-time and smooth operation of the 1 800 m3 BF is guaranteed .%针对2013年1月16日宣钢1800 m3高炉炉缸碳砖温度大幅度异常升高。通过正确诊断炉体侵蚀状况,采取提高入炉钛负荷、提高冷却强度、加强铁口维护保证铁口深度、出铁及时倒场等多项护炉措施,消除了安全隐患,保证了1800 m3高炉炉况长期稳定顺行。

  1. M3(Au,Ge)19 and M(3.25)(Au,Ge)18 (M = Ca, Yb): distinctive phase separations driven by configurational disorder in cubic YCd6-type derivatives.

    Science.gov (United States)

    Lin, Qisheng; Corbett, John D

    2010-05-17

    Exploratory syntheses in the M-Au-Ge (M = Ca, Yb) systems have led to the discovery of two cleanly separated non-stoichiometric phases M(3)Au(approximately 14.4)Ge(approximately 4.6) (I) and M(3.25)Au(approximately 12.7)Ge(approximately 5.3) (II). Single crystal X-ray studies reveal that both (space group Im3) feature body-centered-cubic packing of five-shell multiply endohedral clusters that resemble those in the parent YCd(6) (= Y(3)Cd(18)) and are akin to approximate phases in other quasicrystal systems. However, differences resulting from various disorders in these are distinctive. The innermost cluster in the M(3)Au(approximately 14.4)Ge(approximately 4.6) phase (I) remains a disordered tetrahedron, as in the YCd(6) parent. In contrast, its counterpart in the electron-richer M(3.25)Au(approximately 12.7)Ge(approximately 5.3) phase (II) is a "rattling" M atom. The structural differentiations between I and II exhibit strong correlations between lattice parameters, cluster sizes, particular site occupancies, and valence electron counts.

  2. Spectral-collocation variational integrators

    Science.gov (United States)

    Li, Yiqun; Wu, Boying; Leok, Melvin

    2017-03-01

    Spectral methods are a popular choice for constructing numerical approximations for smooth problems, as they can achieve geometric rates of convergence and have a relatively small memory footprint. In this paper, we introduce a general framework to convert a spectral-collocation method into a shooting-based variational integrator for Hamiltonian systems. We also compare the proposed spectral-collocation variational integrators to spectral-collocation methods and Galerkin spectral variational integrators in terms of their ability to reproduce accurate trajectories in configuration and phase space, their ability to conserve momentum and energy, as well as the relative computational efficiency of these methods when applied to some classical Hamiltonian systems. In particular, we note that spectrally-accurate variational integrators, such as the Galerkin spectral variational integrators and the spectral-collocation variational integrators, combine the computational efficiency of spectral methods together with the geometric structure-preserving and long-time structural stability properties of symplectic integrators.

  3. The Relative Spectral Response Calibration of the ISO-SWS

    NARCIS (Netherlands)

    Vandenbussche, B.; Morris, P. W.; Valentijn, E. A.; Beintema, D. A.; Boxhoorn, D. R.; Decin, L.; de Graauw, T.; Feuchtgruber, H.; Heras, A. M.; Lahuis, F.; Lorente, R.; Lutz, D.; Roelfsema, P. R.; Salama, A.; Shipman, R. F.; van Malderen, R.; Wieprecht, E.

    2001-01-01

    The Relative Spectral Response Function (RSRF) characterises the wavelength dependent response of a spectrometer. The wavelength range of the grating section of the ISO-SWS is covered in 15 spectral bands for each of which the RSRF has to be determined. We discuss how the RSRF was measured during th

  4. The X-shooter Spectral Library and Carbon stars

    NARCIS (Netherlands)

    Gonneau, A.; Lançon, A.; Trager, S. C.; Chen, Y.; Peletier, R.; Aringer, B.; Nowotny, W.; Cambrésy, L.; Martins, F.; Nuss, E.; Palacios, A.

    2013-01-01

    Until recently, most empirical stellar spectral libraries were limited to a certain wavelength range or combined data from different stars, taken by different instruments of which some have low spectral resolution, limiting for instance our ability to analyze galaxies jointly in the ultraviolet, the

  5. Rapid Measurement of Spectral Characteristics by Correlation Matching Method

    CERN Document Server

    Kim, Chol-Sun; Im, Song-Jin

    2015-01-01

    In this paper, we have established the couple system of a spectroscope, CCD and computer and proposed a method of the rapid measurement on spectral characteristics such as central wavelengths, relative intensities, sensitivity lines and the wavelength range and image pixel of the spectral images of a material by using the correlation matching method for the image discernment of digital spectra.

  6. Comparative study of AISI M3:2 high speed steel produced through different techniques of manufacturing; Estudo comparativo de acos rapidos AISI M3:2 produzidos por diferentes processos de fabricacao

    Energy Technology Data Exchange (ETDEWEB)

    Araujo Filho, Oscar Olimpio de

    2006-07-01

    In this work AISI M3:2 high speed steels obtained through different techniques of manufacturing, submitted to the same heat treatment procedure were evaluated by measuring their mechanical properties of transverse rupture strength and hardness. Sinter 23 obtained by hot isostatic pressing (HIP), VWM3C obtained by the conventional route and a M3:2 high speed steel obtained by cold compaction of water atomized powders and vacuum sintered with and without the addition of a small quantity of carbon were evaluated after the same heat treatment procedure. The vacuum sintered M3:2 high speed steel can be an alternative to the more expensive high speed steel produced by hot isostatic pressing and with similar properties presented by the conventional one. The characterization of the vacuum sintered M3:2 high speed steel was performed by measuring the densities of the green compacts and after the sintering cycle. The sintering produced an acceptable microstructure and densities near to the theoretical. The transverse rupture strength was evaluated by means of three point bending tests and the hardness by means of Rockwell C and Vickers tests. The technique of scanning electronic microscopy (SEM) was used to evaluate the microstructure and to establish a relation with the property of transverse rupture strength. The structure was determined by means of X-ray diffraction (XRD) patterns and the retained austenite was detected to all the conditions of heat treatment. The main contribution of this work is to establish a relation between the microstructure and the mechanical property of transverse rupture strength and to evaluate the AISI M3:2 vacuum sintered high speed steel as an alternative to the similar commercial high speed steels. (author)

  7. Milestone Report - M3FT-15OR03120215 - Recommend HIP Conditions for AgZ

    Energy Technology Data Exchange (ETDEWEB)

    Bruffey, Stephanie H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jubin, Robert Thomas [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-09-18

    The purpose of this study was to continue research to determine if HIPing could directly convert I-Ag0Z into a suitable waste form. Fiscal year (FY) 2015 work completed studies of Phase IIA, IIB, and IIC samples. Product consistency testing (PCT) of Phase IIA samples resulted in iodine release below detection limit for six of twelve samples. This is promising and indicates that a durable waste form may be produced through HIPing even if transformation of the zeolite to a distinct mineral phase does not occur. From PCT results of Phase IIA samples, it was determined that future pressing should be conducted at a temperature of 900°C. Phase IIC testing continued production of samples to examine the effects of multiple source materials, compositional variations, and an expanded temperature range. The density of each sample was determined and x-ray diffraction (XRD) patterns were obtained. In all cases, there was nothing in the XRD analyses to indicate the creation of any AgI-containing silicon phase; the samples were found to be largely amorphous.

  8. Precise acquisition and unsupervised segmentation of multi-spectral images

    DEFF Research Database (Denmark)

    Gomez, David Delgado; Clemmensen, Line Katrine Harder; Ersbøll, Bjarne Kjær

    2007-01-01

    In this work, an integrated imaging system to obtain accurate and reproducible multi-spectral images and a novel multi-spectral image segmentation algorithm are proposed. The system collects up to 20 different spectral bands within a range that vary from 395 nm to 970 nm. The system is designed...... to acquire geometrically and chromatically corrected images in homogeneous and diffuse illumination, so images can be compared over time. The proposed segmentation algorithm combines the information provided by all the spectral bands to segment the different regions of interest. Three experiments...

  9. Reactor Dosimetry Applications Using RAPTOR-M3G:. a New Parallel 3-D Radiation Transport Code

    Science.gov (United States)

    Longoni, Gianluca; Anderson, Stanwood L.

    2009-08-01

    The numerical solution of the Linearized Boltzmann Equation (LBE) via the Discrete Ordinates method (SN) requires extensive computational resources for large 3-D neutron and gamma transport applications due to the concurrent discretization of the angular, spatial, and energy domains. This paper will discuss the development RAPTOR-M3G (RApid Parallel Transport Of Radiation - Multiple 3D Geometries), a new 3-D parallel radiation transport code, and its application to the calculation of ex-vessel neutron dosimetry responses in the cavity of a commercial 2-loop Pressurized Water Reactor (PWR). RAPTOR-M3G is based domain decomposition algorithms, where the spatial and angular domains are allocated and processed on multi-processor computer architectures. As compared to traditional single-processor applications, this approach reduces the computational load as well as the memory requirement per processor, yielding an efficient solution methodology for large 3-D problems. Measured neutron dosimetry responses in the reactor cavity air gap will be compared to the RAPTOR-M3G predictions. This paper is organized as follows: Section 1 discusses the RAPTOR-M3G methodology; Section 2 describes the 2-loop PWR model and the numerical results obtained. Section 3 addresses the parallel performance of the code, and Section 4 concludes this paper with final remarks and future work.

  10. Bonding the superalkali M3O (M = Li and K): An effective strategy to improve the electronic and nonlinear optical properties of the inorganic B40 nanocage

    Science.gov (United States)

    Li, Zhipeng; Yu, Guangtao; Zhang, Xueying; Huang, Xuri; Chen, Wei

    2017-10-01

    Inspired by the fascinating finding of all-boron fullerene B40 (Nat Chem, 2014, 6, 727), we propose a new and effective strategy to construct a series of typical Donor-Acceptor (D-A) frameworks via linking the superalkali M3O (M = Li and K) unit with the low ionization potential to the B40 nanocage with large electron affinity. By means of the density functional theory computations, we have systematically investigated the structures, electronic properties, the first and second hyperpolarizabilities of these modified B40 nanocage systems. Owing to the formation of a B-O chemical bond, these composite systems (M3O)n-B40 (M = Li and K, n = 1 and 2) can possess the considerably large binding energy ranging from 57.0 to 99.8 kcal/mol, indicating their high structure stabilities. Compared with the pristine B40 nanocage, linking the superalkali M3O can effectively narrow the wide energy gap from the original 2.86 eV to 0.61-1.11 eV, and significantly increase the first and second hyperpolarizabilities to as large as 5.00 × 104-2.46 × 105 au and 1.48 × 107-4.85 × 108 au, respectively, owing to the occurrence of evident electron transfer process in this kind of typical D-A framework. These fascinating findings will be advantageous for promoting the potential applications of the inorganic boron-based nanosystems in the new type of electronic nanodevices and high-performance nonlinear optical materials.

  11. Studying stellar populations at high spectral resolution

    CERN Document Server

    Bruzual, Gustavo A

    2007-01-01

    I describe very briefly the new libraries of empirical spectra of stars covering wide ranges of values of the atmospheric parameters Teff, log g, [Fe/H], as well as spectral type, that have become available in the recent past, among them the HNGSL, MILES, UVES-POP, ELODIE, and the IndoUS libraries. I show the results of using the IndoUS and the HNGSL libraries, as well as an atlas of theoretical model atmospheres, to build population synthesis models. These libraries are complementary in spectral resolution and wavelength coverage, and will prove extremely useful to describe spectral features expected in galaxy spectra from the NUV to the NIR. The fits to observed galaxy spectra using simple and composite stellar population models are discussed.

  12. Spectrally multiplexed chromatic confocal multipoint sensing.

    Science.gov (United States)

    Hillenbrand, Matthias; Lorenz, Lucia; Kleindienst, Roman; Grewe, Adrian; Sinzinger, Stefan

    2013-11-15

    We present a concept for chromatic confocal distance sensing that employs two levels of spectral multiplexing for the parallelized evaluation of multiple lateral measurement points; at the first level, the chromatic confocal principle is used to encode distance information within the spectral distribution of the sensor signal. For lateral multiplexing, the total spectral bandwidth of the sensor is split into bands. Each band is assigned to a different lateral measurement point by a segmented diffractive element. Based on this concept, we experimentally demonstrate a chromatic confocal three-point sensor that is suitable for harsh production environments, since it works with a single-point spectrometer and does not require scanning functionality. The experimental system has a working distance of more than 50 mm, a measurement range of 9 mm, and an axial resolution of 50 μm.

  13. Anomalous spectral lines and relic quantum nonequilibrium

    CERN Document Server

    Underwood, Nicolas G

    2016-01-01

    We describe general features that might be observed in the line spectra of relic cosmological particles should quantum nonequilibrium be preserved in their statistics. According to our arguments, these features would represent a significant departure from those of a conventional origin. Among other features, we find a possible spectral broadening (for incident photons) that is proportional to the energy resolution of the recording telescope (and so could be orders of magnitude larger than any intrinsic broadening). Notably, for a range of possible initial conditions we find the possibility of spectral line `narrowing' whereby a telescope could observe a spectral line which is narrower than it should conventionally be able to resolve. We briefly discuss implications for the indirect search for dark matter.

  14. Lead generation using pharmacophore mapping and three-dimensional database searching: application to muscarinic M(3) receptor antagonists.

    Science.gov (United States)

    Marriott, D P; Dougall, I G; Meghani, P; Liu, Y J; Flower, D R

    1999-08-26

    By using a pharmacophore model, a geometrical representation of the features necessary for molecules to show a particular biological activity, it is possible to search databases containing the 3D structures of molecules and identify novel compounds which may possess this activity. We describe our experiences of establishing a working 3D database system and its use in rational drug design. By using muscarinic M(3) receptor antagonists as an example, we show that it is possible to identify potent novel lead compounds using this approach. Pharmacophore generation based on the structures of known M(3) receptor antagonists, 3D database searching, and medium-throughput screening were used to identify candidate compounds. Three compounds were chosen to define the pharmacophore: a lung-selective M(3) antagonist patented by Pfizer and two Astra compounds which show affinity at the M(3) receptor. From these, a pharmacophore model was generated, using the program DISCO, and this was used subsequently to search a UNITY 3D database of proprietary compounds; 172 compounds were found to fit the pharmacophore. These compounds were then screened, and 1-[2-(2-(diethylamino)ethoxy)phenyl]-2-phenylethanone (pA(2) 6.67) was identified as the best hit, with N-[2-(piperidin-1-ylmethyl)cycohexyl]-2-propoxybenz amide (pA(2) 4. 83) and phenylcarbamic acid 2-(morpholin-4-ylmethyl)cyclohexyl ester (pA(2) 5.54) demonstrating lower activity. As well as its potency, 1-[2-(2-(diethylamino)ethoxy)phenyl]-2-phenylethanone is a simple structure with limited similarity to existing M(3) receptor antagonists.

  15. Spectral compression of single photons

    CERN Document Server

    Lavoie, Jonathan; Wright, Logan G; Fedrizzi, Alessandro; Resch, Kevin J

    2013-01-01

    Photons are critical to quantum technologies since they can be used for virtually all quantum information tasks: in quantum metrology, as the information carrier in photonic quantum computation, as a mediator in hybrid systems, and to establish long distance networks. The physical characteristics of photons in these applications differ drastically; spectral bandwidths span 12 orders of magnitude from 50 THz for quantum-optical coherence tomography to 50 Hz for certain quantum memories. Combining these technologies requires coherent interfaces that reversibly map centre frequencies and bandwidths of photons to avoid excessive loss. Here we demonstrate bandwidth compression of single photons by a factor 40 and tunability over a range 70 times that bandwidth via sum-frequency generation with chirped laser pulses. This constitutes a time-to-frequency interface for light capable of converting time-bin to colour entanglement and enables ultrafast timing measurements. It is a step toward arbitrary waveform generatio...

  16. Active spectral imaging and mapping

    Science.gov (United States)

    Steinvall, Ove

    2014-04-01

    Active imaging and mapping using lasers as illumination sources have been of increasing interest during the last decades. Applications range from defense and security, remote sensing, medicine, robotics, and others. So far, these laser systems have mostly been based on a fix wavelength laser. Recent advances in lasers enable emission of tunable, multiline, or broadband emission, which together with the development of array detectors will extend the capabilities of active imaging and mapping. This paper will review some of the recent work on active imaging mainly for defense and security and remote sensing applications. A short survey of basic lidar relations and present fix wavelength laser systems is followed by a review of the benefits of adding the spectral dimension to active and/or passive electro-optical systems.

  17. Solar spectral irradiance changes during cycle 24

    Energy Technology Data Exchange (ETDEWEB)

    Marchenko, S. V.; DeLand, M. T. [Also at NASA/Goddard Space Flight Center, Greenbelt, MD, USA. (United States)

    2014-07-10

    We use solar spectra obtained by the Ozone Monitoring Instrument (OMI) on board the Aura satellite to detect and follow long-term (years) and short-term (weeks) changes in the solar spectral irradiance (SSI) in the 265-500 nm spectral range. During solar Cycle 24, in the relatively line-free regions the SSI changed by ∼0.6% ± 0.2% around 265 nm. These changes gradually diminish to 0.15% ± 0.20% at 500 nm. All strong spectral lines and blends, with the notable exception of the upper Balmer lines, vary in unison with the solar 'continuum'. Besides the lines with strong chromospheric components, the most involved species include Fe I blends and all prominent CH, NH, and CN spectral bands. Following the general trend seen in the solar 'continuum', the variability of spectral lines also decreases toward longer wavelengths. The long-term solar cycle SSI changes are closely, to within the quoted 0.1%-0.2% uncertainties, matched by the appropriately adjusted short-term SSI variations derived from the 27 day rotational modulation cycles. This further strengthens and broadens the prevailing notion about the general scalability of the UV SSI variability to the emissivity changes in the Mg II 280 nm doublet on timescales from weeks to years. We also detect subtle deviations from this general rule: the prominent spectral lines and blends at λ ≳ 350 nm show slightly more pronounced 27 day SSI changes when compared to the long-term (years) trends. We merge the solar data from Cycle 21 with the current Cycle 24 OMI and GOME-2 observations and provide normalized SSI variations for the 170-795 nm spectral region.

  18. Extended inertial range phenomenology of magnetohydrodynamic turbulence

    Science.gov (United States)

    Matthaeus, William H.; Zhou, YE

    1989-01-01

    A phenomenological treatment of the inertial range of isotropic statistically steady magnetohydrodynamic turbulence is presented, extending the theory of Kraichnan (1965). The role of Alfven wave propagation is treated on equal footing with nonlinear convection, leading to a simple generalization of the relations between the times characteristic of wave propagation, convection, energy transfer, and decay of triple correlations. The theory leads to a closed-form steady inertial range spectral law that reduces to the Kraichnan and Kolmogorov laws in appropriate limits. The Kraichnan constant is found to be related in a simple way to the Kolmogorov constant; for typical values of the latter constant, the former has values in the range 1.22-1.87. Estimates of the time scale associated with spectral transfer of energy also emerge from the new approach, generalizing previously presented 'golden rules' for relating the spectral transfer time scale to the Alfven and eddy-turnover time scales.

  19. Spectral variability of the particulate backscattering ratio

    Science.gov (United States)

    Whitmire, A. L.; Boss, E.; Cowles, T. J.; Pegau, W. S.

    2007-05-01

    The spectral dependency of the particulate backscattering ratio is relevant in the fields of ocean color inversion, light field modeling, and inferring particle properties from optical measurements. Aside from theoretical predictions for spherical, homogeneous particles, we have very limited knowledge of the actual in situ spectral variability of the particulate backscattering ratio. This work presents results from five research cruises that were conducted over a three-year period. Water column profiles of physical and optical properties were conducted across diverse aquatic environments that offered a wide range of particle populations. The main objective of this research was to examine the behavior of the spectral particulate backscattering ratio in situ, both in terms of its absolute magnitude and its variability across visible wavelengths, using over nine thousand 1-meter binned data points for each of five wavelengths of the spectral particulate backscattering ratio. Our analysis reveals no spectral dependence of the particulate backscattering ratio within our measurement certainty, and a geometric mean value of 0.013 for this dataset. This is lower than the commonly used value of 0.0183 from Petzold’s integrated volume scattering data. Within the first optical depth of the water column, the mean particulate backscattering ratio was 0.010.

  20. 高顶压技术在莱钢1000m3高炉的应用%Application of High Top Pressure Technology in Laigang 1000 m3 Blast Furnace

    Institute of Scientific and Technical Information of China (English)

    王丰巧

    2015-01-01

    高压操作是强化高炉冶炼的一项重要措施,利于高炉炉况稳定顺行、提高煤气利用率,莱钢1000 m3高炉通过加强原料管理、增加鼓风动能、加强炉前管理等措施提高炉顶压力,取得了显著的经济效益。%High pressure operation is an important measure to strengthen the blast furnace smelting of blast furnace, can be conducive to the stable operation and the exploitation rate of gas.By improving raw material management, increasing the en-ergy of blast furnace, strengthening management measures to strengthen blast furnace top pressure, remarkable economic benefits has been achieved for Laigang 1000 m3 furnace.

  1. Development of Protection System Preventing 60 000 m3 Air Compressor from Stall%60000m3空压机喘振保护系统的研发

    Institute of Scientific and Technical Information of China (English)

    李学波

    2014-01-01

    This article describes the reason and harm of air compressor stall in detail ,and elaborates the principle of the anti-stall control system .A protection system for 60 000 m3 air compressor is set up .By using the function of DCS and PLC ,we can make the control of compressor fast and reliable .This work has important reference value to the other anti-stall control systems .%简述了喘振的原理及危害。详细阐述了防喘振系统的控制原理,并建立了60000 m3空压机的保护系统,利用DCS和PLC的强大功能实现快速可靠的控制,对其他系统的防喘振控制有着重要的参考价值。

  2. M3 version 3.0: Verification and validation; Hydrochemical model of ground water at repository site

    Energy Technology Data Exchange (ETDEWEB)

    Gomez, Javier B. (Dept. of Earth Sciences, Univ. of Zaragoza, Zaragoza (Spain)); Laaksoharju, Marcus (Geopoint AB, Sollentuna (Sweden)); Skaarman, Erik (Abscondo, Bromma (Sweden)); Gurban, Ioana (3D-Terra (Canada))

    2009-01-15

    Hydrochemical evaluation is a complex type of work that is carried out by specialists. The outcome of this work is generally presented as qualitative models and process descriptions of a site. To support and help to quantify the processes in an objective way, a multivariate mathematical tool entitled M3 (Multivariate Mixing and Mass balance calculations) has been constructed. The computer code can be used to trace the origin of the groundwater, and to calculate the mixing proportions and mass balances from groundwater data. The M3 code is a groundwater response model, which means that changes in the groundwater chemistry in terms of sources and sinks are traced in relation to an ideal mixing model. The complexity of the measured groundwater data determines the configuration of the ideal mixing model. Deviations from the ideal mixing model are interpreted as being due to reactions. Assumptions concerning important mineral phases altering the groundwater or uncertainties associated with thermodynamic constants do not affect the modelling because the calculations are solely based on the measured groundwater composition. M3 uses the opposite approach to that of many standard hydrochemical models. In M3, mixing is evaluated and calculated first. The constituents that cannot be described by mixing are described by reactions. The M3 model consists of three steps: the first is a standard principal component analysis, followed by mixing and finally mass balance calculations. The measured groundwater composition can be described in terms of mixing proportions (%), while the sinks and sources of an element associated with reactions are reported in mg/L. This report contains a set of verification and validation exercises with the intention of building confidence in the use of the M3 methodology. At the same time, clear answers are given to questions related to the accuracy and the precision of the results, including the inherent uncertainties and the errors that can be made

  3. M3 version 3.0: Verification and validation; Hydrochemical model of ground water at repository site

    Energy Technology Data Exchange (ETDEWEB)

    Gomez, Javier B. (Dept. of Earth Sciences, Univ. of Zaragoza, Zaragoza (Spain)); Laaksoharju, Marcus (Geopoint AB, Sollentuna (Sweden)); Skaarman, Erik (Abscondo, Bromma (Sweden)); Gurban, Ioana (3D-Terra (Canada))

    2009-01-15

    Hydrochemical evaluation is a complex type of work that is carried out by specialists. The outcome of this work is generally presented as qualitative models and process descriptions of a site. To support and help to quantify the processes in an objective way, a multivariate mathematical tool entitled M3 (Multivariate Mixing and Mass balance calculations) has been constructed. The computer code can be used to trace the origin of the groundwater, and to calculate the mixing proportions and mass balances from groundwater data. The M3 code is a groundwater response model, which means that changes in the groundwater chemistry in terms of sources and sinks are traced in relation to an ideal mixing model. The complexity of the measured groundwater data determines the configuration of the ideal mixing model. Deviations from the ideal mixing model are interpreted as being due to reactions. Assumptions concerning important mineral phases altering the groundwater or uncertainties associated with thermodynamic constants do not affect the modelling because the calculations are solely based on the measured groundwater composition. M3 uses the opposite approach to that of many standard hydrochemical models. In M3, mixing is evaluated and calculated first. The constituents that cannot be described by mixing are described by reactions. The M3 model consists of three steps: the first is a standard principal component analysis, followed by mixing and finally mass balance calculations. The measured groundwater composition can be described in terms of mixing proportions (%), while the sinks and sources of an element associated with reactions are reported in mg/L. This report contains a set of verification and validation exercises with the intention of building confidence in the use of the M3 methodology. At the same time, clear answers are given to questions related to the accuracy and the precision of the results, including the inherent uncertainties and the errors that can be made

  4. Restoration of Bottom Plate Leakage at 80,000 m3 Wiggins Gasholder%8万m3威金斯煤气柜柜底板泄漏修复

    Institute of Scientific and Technical Information of China (English)

    董永涛

    2015-01-01

    8万m3威金斯柜在生产运行中柜底板发生泄漏,采取临时措施封堵后效果不佳,为了避免事态扩大停柜检修,针对柜底板蜂窝状腐蚀,以托补钢板的形式予以加强,消除煤气泄漏的安全隐患.

  5. 基于ARM Cortex-M3的步进电机线性速度控制的实现%The Realization of Linear Speed Control of Stepper Motor Based on ARM Cortex-M3

    Institute of Scientific and Technical Information of China (English)

    罗鑫; 张峰

    2009-01-01

    Conex-M3是ARM公司最新推出的基于ARMy7体系架构的处理核.步进电机已被广泛的应用于速度、位置等控制领域.本文实现了基于Codex-M3内核处理器的步进电机的线性速度控制.针对步进电机控制过程中易出现的失步和过冲现象,提出了一种步进电机加减速控制算法.首先,在Codex-M3内核处理器上移植了μCOS-Ⅱ实时操作系统.在此基础上,利用系统的API接口函数用程序实现了加减速控制算法,并最终实现了对两路步进电机的控制.

  6. Spectral Ages of CSOs and CSS Sources

    CERN Document Server

    Murgia, M

    2003-01-01

    This paper deals with the spectral ageing study of a representative sample of compact symmetric objects (CSOs) and compact steep spectrum (CSS) sources. Observations reveal a distinctive high-frequency steepening of the radio spectra of many of these sources. The existence of such a spectral feature is expected or may be naturally interpreted in terms of radiative ageing of synchrotron emitting electrons. The small angular size of CSS sources makes it relatively easy to measure their integrated spectra over a wide frequency range for a conspicuous number of objects. For those sources whose emission is dominated by the mini-lobes, the integrated spectra can be used to constrain the source age. Assuming equipartition magnetic fields, the spectral ages we found are in the range from 10^2 to 10^5 yr. Multifrequency VLBA observations allow us to study the spectral properties of two CSOs: B1323+321 and B1943+546. The case of B1943+546 is particularly interesting since for this source a kinematic age has been derive...

  7. [Biological experiments in flights of unmanned space craft Foton-M2 and Foton-M3].

    Science.gov (United States)

    Ilyin, E A

    2013-01-01

    Missions of unmanned spacecraft Foton-M2 (2005) and Foton-M3 (2007) of 16 and 12 days in duration, respectively, provided an opportunity to conduct the Russian/US experiments with snails (Helix lucorum and Helix aspera), newts (Pleurodeles waltli), geckos (Pachydactilus turneri) and microorganisms (Streptomyces lividans 66, E. coli and others). Besides, Foton-M3 carried a Russian experiment with Mongolian gerbils (Meriones unguiculatus). Objectives of the space experiments were to study the micro-g effects on the living systems' behavior, structure and functioning, post-traumatic regeneration of bone and organs, stable inheritance of plasmid pIJ 702, and melanin pigment synthesis by streptomycets. The survey paper presents the major findings of a large team of investigators.

  8. Electrochemical properties of mixed conducting (La,M)(CoFe) oxide perovskites (M=3DSr, Ca, and Ba)

    Energy Technology Data Exchange (ETDEWEB)

    Stevenson, J.W.; Armstrong, T.R.; Bates, J.L. [and others

    1996-04-01

    Electrical properties and oxygen permeation properties of solid mixed-conducting electrolytes (La,M)(CoFe) oxide perovskites (M=3DSr, Ca, and Ba) have been characterized. These materials are potentially useful as passive membranes to separate high purity oxygen from air and as the cathode in a fuel cell. Dilatometric linear expansion measurements were performed as a function of temperature and oxygen partial pressure to evaluate the stability.

  9. The Armys M-1 Abrams, M-2/M-3 Bradley, and M-1126 Stryker: Background and Issues for Congress

    Science.gov (United States)

    2016-04-05

    entered service with the Army in 1980; the M-2/M-3 Bradley Fighting Vehicle in 1981; and the Stryker Combat Vehicle in 2001. Under current Army... Under current Army modernization plans, the Army envisions all three vehicles in service with Active and National Guard forces beyond FY2028...Information from this section, unless otherwise noted, is taken from Jane’s Armour and Artillery, 2011-2012, pp.177- 185, and the author’s personal

  10. Inhalation by design: dual pharmacology β-2 agonists/M3 antagonists for the treatment of COPD.

    Science.gov (United States)

    Jones, Lyn H; Baldock, Helen; Bunnage, Mark E; Burrows, Jane; Clarke, Nick; Coghlan, Michele; Entwistle, David; Fairman, David; Feeder, Neil; Fulton, Craig; Hilton, Laura; James, Kim; Jones, Rhys M; Kenyon, Amy S; Marshall, Stuart; Newman, Sandra D; Osborne, Rachel; Patel, Sheena; Selby, Matthew D; Stuart, Emilio F; Trevethick, Michael A; Wright, Karen N; Price, David A

    2011-05-01

    This paper describes the successful design and development of dual pharmacology β-2 agonists-M3 antagonists, for the treatment of chronic obstructive pulmonary disorder using the principles of 'inhalation by design'. A key feature of this work is the combination of balanced potency and pharmacodynamic duration with desirable pharmacokinetic and material properties, whilst keeping synthetic complexity to a minimum. Copyright © 2010 Elsevier Ltd. All rights reserved.

  11. Spectral signatures of chirality

    DEFF Research Database (Denmark)

    Pedersen, Jesper Goor; Mortensen, Asger

    2009-01-01

    We present a new way of measuring chirality, via the spectral shift of photonic band gaps in one-dimensional structures. We derive an explicit mapping of the problem of oblique incidence of circularly polarized light on a chiral one-dimensional photonic crystal with negligible index contrast...... to the formally equivalent problem of linearly polarized light incident on-axis on a non-chiral structure with index contrast. We derive analytical expressions for the first-order shifts of the band gaps for negligible index contrast. These are modified to give good approximations to the band gap shifts also...

  12. Spectrally encoded confocal microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Tearney, G.J.; Webb, R.H.; Bouma, B.E. [Wellman Laboratories of Photomedicine, Massachusetts General Hospital, 50 Blossom Street, BAR 703, Boston, Massachusetts 02114 (United States)

    1998-08-01

    An endoscope-compatible, submicrometer-resolution scanning confocal microscopy imaging system is presented. This approach, spectrally encoded confocal microscopy (SECM), uses a quasi-monochromatic light source and a transmission diffraction grating to detect the reflectivity simultaneously at multiple points along a transverse line within the sample. Since this method does not require fast spatial scanning within the probe, the equipment can be miniaturized and incorporated into a catheter or endoscope. Confocal images of an electron microscope grid were acquired with SECM to demonstrate the feasibility of this technique. {copyright} {ital 1998} {ital Optical Society of America}

  13. Implications for Damage Recognition during Dpo4-Mediated Mutagenic Bypass of m1G and m3C Lesions

    Energy Technology Data Exchange (ETDEWEB)

    Rechkoblit, Olga; Delaney, James C.; Essigmann, John M.; Patel, Dinshaw J. (MIT); (MSKCC)

    2012-05-08

    DNA is susceptible to alkylation damage by a number of environmental agents that modify the Watson-Crick edge of the bases. Such lesions, if not repaired, may be bypassed by Y-family DNA polymerases. The bypass polymerase Dpo4 is strongly inhibited by 1-methylguanine (m1G) and 3-methylcytosine (m3C), with nucleotide incorporation opposite these lesions being predominantly mutagenic. Further, extension after insertion of both correct and incorrect bases, introduces additional base substitution and deletion errors. Crystal structures of the Dpo4 ternary extension complexes with correct and mismatched 3'-terminal primer bases opposite the lesions reveal that both m1G and m3C remain positioned within the DNA template/primer helix. However, both correct and incorrect pairing partners exhibit pronounced primer terminal nucleotide distortion, being primarily evicted from the DNA helix when opposite m1G or misaligned when pairing with m3C. Our studies provide insights into mechanisms related to hindered and mutagenic bypass of methylated lesions and models associated with damage recognition by repair demethylases.

  14. Drop by drop backscattered signal of a 50 × 50 × 50 m3 volume: A numerical experiment

    Science.gov (United States)

    Gires, A.; Tchiguirinskaia, I.; Schertzer, D.

    2016-09-01

    The goal of this paper is to analyse the influence of individual drop positions on a backscattered radar signal. This is achieved through a numerical experiment: a 3D rain drop field generator is developed and implemented over a volume of 50 × 50 × 50 m3, and then the sum of the electromagnetic waves backscattered by its hydrometeors is computed. Finally the temporal evolution over 1 s is modelled with simplistic assumptions. For the rainfall generator, the liquid water content (LWC) distribution is represented with the help of a multiplicative cascade down to 0.5 m, below which it is considered as homogeneous. Within each 0.5 × 0.5 × 0.5 m3 patch, liquid water is distributed into drops, located randomly uniformly according to a pre-defined drop size distribution (DSD). Such configuration is compared with the one consisting of the same drops being uniformly distributed over the entire 50 × 50 × 50 m3 volume. Due to the fact that the radar wave length is much smaller than the size of a rainfall "patch", it appears that, in agreement with the theory, we retrieve an exponential distribution for potential measures on horizontal reflectivity. Much thinner dispersion is noticed for differential reflectivity. We show that a simple ballistic assumption for drop velocities does not enable the reproduction of radar observations, and turbulence should be taken into account. Finally the sensitivity of these outputs to the various model parameters is quantified.

  15. The surface accessibility of the glycine receptor M2-M3 loop is increased in the channel open state.

    Science.gov (United States)

    Lynch, J W; Han, N L; Haddrill, J; Pierce, K D; Schofield, P R

    2001-04-15

    Mutations in the extracellular M2-M3 loop of the glycine receptor (GlyR) alpha1 subunit have been shown previously to affect channel gating. In this study, the substituted cysteine accessibility method was used to investigate whether a structural rearrangement of the M2-M3 loop accompanies GlyR activation. All residues from R271C to V277C were covalently modified by both positively charged methanethiosulfonate ethyltrimethylammonium (MTSET) and negatively charged methanethiosulfonate ethylsulfonate (MTSES), implying that these residues form an irregular surface loop. The MTSET modification rate of all residues from R271C to K276C was faster in the glycine-bound state than in the unliganded state. MTSES modification of A272C, L274C, and V277C was also faster in the glycine-bound state. These results demonstrate that the surface accessibility of the M2-M3 loop is increased as the channel transitions from the closed to the open state, implying that either the loop itself or an overlying domain moves during channel activation.

  16. Synthesis and characterization of M3V2O8 (M = Ca, Sr and Ba) by a solid-state metathesis approach

    Indian Academy of Sciences (India)

    Purnendu Parhi; V Manivannan; Sandeep Kohli; Patrick Mccurdy

    2008-11-01

    A solid-state metathesis approach initiated by microwave energy has been successfully applied for the synthesis of orthovanadates, M3V2O8 (M = Ca, Sr, and Ba). The structural, vibrational, thermal, optical and chemical properties of synthesized powders are determined by powder X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, differential scanning calorimetry, magnetic property measurements and diffused reflectance spectra in the UV–VIS range. The direct bandgap of the synthesized materials was found to be 3.55 ± 0.2 eV, 3.75 ± 0.2 eV and 3.57 ± 0.2 eV for Ca3V2O8, Sr3V2O8 and Ba3V2O8, respectively.

  17. Upconversion based spectral imaging in 6 to 8 μm spectral regime

    DEFF Research Database (Denmark)

    Junaid, Saher; Tidemand-Lichtenberg, Peter; Pedersen, Christian

    2017-01-01

    Spectral imaging in the 6 to 8μm range has great potential for medical diagnostics. Here a novel technique based on frequency upconversion of the infrared images to the near visible for subsequent acquisition using a Si-CCD camera is investigated. The upconversion unit consists of an AgGaS2 crystal...

  18. Structural and electronic properties of reduced transition metal oxide clusters, M3O8 and M3O8- (M = Cr, W), from photoelectron spectroscopy and quantum chemical calculations.

    Science.gov (United States)

    Li, Shenggang; Zhai, Hua-Jin; Wang, Lai-Sheng; Dixon, David A

    2009-10-22

    We report a comparative study of reduced transition metal oxide clusters, M(3)O(8)(-) (M = Cr, W) anions and their neutrals, via anion photoelectron spectroscopy (PES) and density functional theory (DFT) and molecular orbital theory (CCSD(T)) calculations. Well-resolved PES spectra are obtained for M(3)O(8)(-) (M = Cr, W) at 193 and 157 nm photon energies. Different PES spectra are observed for M = Cr versus M = W. Extensive DFT and CCSD(T) calculations are performed to locate the ground and low-lying excited states for the neutrals and anions. The ground states of Cr(3)O(8) and Cr(3)O(8)(-) are predicted to be the (3)B(2) and (4)B(2) states of a C(2v) structure, respectively, revealing ferromagnetic spin coupling for Cr 3d electrons. In contrast, the ground states of W(3)O(8) and W(3)O(8)(-) are predicted to be the (1)A' state (C(s) symmetry) and the (2)A(1) state (C(2v) symmetry), respectively, showing metal-metal d-d bonding in the anion. The current cluster geometries are in qualitative agreement with prior DFT studies at the PBE level for M = Cr and the B3LYP level for M = W. The BP86 and PW91 functionals significantly outperform the B3LYP functional for the Cr species, in terms of relative energies, electron detachment energies, and electronic excitation energies, whereas the B3LYP functional is better for the W species. Accurate heats of formation for the ground states of M(3)O(8) are calculated from the clustering energies and the heats of formation of MO(2) and MO(3). The energetics have been used to predict redox reaction thermochemistry.

  19. Analysis of errors in spectral reconstruction with a Laplace transform pair model

    Energy Technology Data Exchange (ETDEWEB)

    Archer, B.R.; Bushong, S.C. (Baylor Univ., Houston, TX (USA). Coll. of Medicine); Wagner, L.K. (Texas Univ., Houston (USA). Dept. of Radiology); Johnston, D.A.; Almond, P.R. (Anderson (M.D.) Hospital and Tumor Inst., Houston, TX (USA))

    1985-05-01

    The sensitivity of a Laplace transform pair model for spectral reconstruction to random errors in attenuation measurements of diagnostic x-ray units has been investigated. No spectral deformation or significant alteration resulted from the simulated attenuation errors. It is concluded that the range of spectral uncertainties to be expected from the application of this model is acceptable for most scientific applications.

  20. The spectral appearance of primeval galaxies

    CERN Document Server

    Guiderdoni, B

    1999-01-01

    The current and forthcoming observations of large samples of high-redshift galaxies selected according to various photometric and spectroscopic criteria can be interpreted in the context of galaxy formation, by means of models of evolving spectral energy distributions (SEDs). We hereafter present STARDUST which gives synthetic SEDs from the far UV to the submm wavelength range. These SEDs are designed to be implemented into semi-analytic models of galaxy formation.

  1. Design of Instrument Lathe Control System Based on CORTEX-M3 Technology%基于CORTEX-M3技术的仪表车床控制系统设计

    Institute of Scientific and Technical Information of China (English)

    李香泉; 刘浪; 洪耀球

    2012-01-01

    采用了基于CORTEX-M3核的STM32F103VCT6 ARM芯片作为核心,实现4轴步进电机控制功能,同时系统还实现了与基于MODBUS RTU协议的文本显示或工业触摸屏的通信功能,以及获取相关输入信号和控制继电器功能.

  2. 8×104m3威金斯转炉煤气柜密封膜破损修复处理%Renovation the Broken Sealing Membrane of 8×104m3 Wiggins Converter Gas Tank

    Institute of Scientific and Technical Information of China (English)

    王树奇; 张军; 刘芳荣

    2013-01-01

    文章介绍了8× 104m3威金斯转炉煤气柜发生密封膜破损泄漏事故,分析了密封膜损坏的原因分析.希望通过此次事故,能提高运行人员和点检人员对八万转炉煤气柜的高度认识和密切关注,在以后的工作当中,避免此类事情的发生.

  3. lOT Data Acquisition Substation for forestry ecology monitor Based on Cortex- M3%Cortex—M3的生态物联网数据采集分站设计

    Institute of Scientific and Technical Information of China (English)

    李骏慧; 陶华; 俞哲伟; 宋军

    2011-01-01

    The IOT(Internet of things)data acquisition substation for forestry ecology monitor is proposed, which employs the Cortex- M3 processor as the CPU. Digital temperature humidity sensor, smoke sensor, C()2 sensor and digital luminance sensor are employed to acquire the environment information which is related with forestry ecology. Then the sensors data are collected by LM3S811 and ID of substation is added to data packet. Further more, LM3SSll transmits the data packet to servers using RF module.%以Cortex—M3处理器LM3S811为核心,设计了面向森林生态监测的物联网数据采集终端分站系统。通过单总线数字式温湿度传感器、烟雾传感器、CO2传感器和环境光亮度传感器分别采集温度、湿度、可燃性颗粒物、CO2含量和光照等与林木生态相关的环境信息和林场防火的相关信息。由LM3S81l处理器处理并添加分站ID和校验码后,采用无线模块传送给服务器。

  4. 100 m3/min往复式空压机长周期安全稳定运行研究%Study on Long, Safe and Stable Operation of 100 m3/min Reciprocating Air Compressor

    Institute of Scientific and Technical Information of China (English)

    陈山

    2015-01-01

    介绍了安徽晋煤中能化工股份有限公司100 m3/min往复式空压机的工况,针对影响机组长周期稳定、安全运行的问题,采取了优化设备结构和工艺结构的措施,优化结果表明:年创造经济效益16.28万元,实现了节能降耗的目的。%This paper introduces the working conditions of 100 m3/min reciprocating air compressor of Anhui Jinmei Zhongneng Chemical Co. , Ltd. To solve the problem affecting long, safe and stable operation of the unit, the author optimizes the structures of the equipment and the process. The opti-mization results show that it has gained 162 800 RMB yuan/a economic benefit and achieved its energy-saving and consumption-reducing purpose.

  5. 石家庄陕鼓2×40000m^3/h空分设备设计优化%Optimized design of Shijiazhuang Shaanxi Blower Group 2 ×40000m^3/h air separation plant

    Institute of Scientific and Technical Information of China (English)

    张岑; 卢子学

    2012-01-01

    At design stage of Shijiazhuang Shaanxi Blower Group 2 ×40000m^3/h air separation plants, it found unreasonable design in the nitrogen compression and supply system, air compressor vent silencer, and connection mode for feeding boosted air to plate-fin type heat exchanger, as well as the factors impairing stable and safe operation of the product continuous supply and air separation plant. Here, the optimization measures taken for the unreasonable factors are described, which puts a sound basis for stable run of the air separation plant.%在石家庄陕鼓2×40000m^3/h空分设备设计阶段,发现氮气压缩和供应系统、空压机放空消声器以及增压空气进板翅式换热器的连接方式设计不舍理,存在影响产品连续供应和空分设备稳定、安全运行的因素。介绍对这些不合理因素所采取的优化措施,为空分设备建成后稳定运行奠定基础。

  6. 3500m3/h绞吸挖泥船甲板机舱振动分析与优化%Analysis and Optimization of Deck Cabin Vibration in 3 500 m3/h Cutter Suction Dredger

    Institute of Scientific and Technical Information of China (English)

    王炜

    2015-01-01

    针对3500 m3/h绞吸式挖泥船的甲板机舱异常振动问题,建立机舱结构有限元模型,进行振动模态分析,发现甲板下支柱与柴油机工作频率耦合引起的共振是导致甲板机舱异常振动的主要原因,进行甲板机舱结构和立柱位置的优化,检测表明,优化后的结构有效避开了共振频率,振动速度峰值和加速度大幅下降,优化效果良好。%In view of abnormal vibration on deck engine room of 3 500 m3/h cutter suction dredger, the FE structural model of the engine room is established.Via the analysis of mode of vibration, resonance coupling of working frequency of the diesel en-gine with the pillar under deck is the primary cause for abnormal vibration of deck engine room.So the location of pillars is rede-signed to avoid the resonant frequency.The test results verify that the peaks of vibration acceleration and velocity are sharply de-creased;the effects of optimization are satisfactory.

  7. Logic control of molecular sieve purification system of 65000m3· h-1 air separation plant%65000m3·h-1空分设备分子筛纯化系统逻辑控制

    Institute of Scientific and Technical Information of China (English)

    朱玉芹

    2012-01-01

    The structure and technical process of molecular sieve purification system of 65000m3/ an air separation plant of Hebi coal and electeicity 600 ktpa methanol project are briefed, automatic valve closing / opening logical control of molecular sieve purification system, automatic / manual operation sequence control program,implementation of the sequence control program and optimized reform of the sequence control configuration program of the molecular sieve absorber in accordance with site operation conditions are described.%简介鹤壁煤电股份有限公司化工分公司空分厂65000m3·h-1空分设备分子筛纯化系统结构和工艺流程,介绍分子筛纯化系统阀门自动开关控制逻辑、顺控程序自动/手动运行、顺控程序执行过程,以及根据现场生产运行实际情况,对分子筛吸附器顺控组态程序进行的优化改进.

  8. Design of Low-cost LCD Touch Screen Based on Cortex-M3%基于Cortex-M3的低成本液晶触摸屏设计

    Institute of Scientific and Technical Information of China (English)

    张勇; 邹卫军

    2014-01-01

    选用NXP公司内置LCD控制器的Cortex-M3处理器LPC1788作为主控,设计了一种低成本的液晶触摸屏。介绍了四线电阻式触摸屏与LPC1788的接口设计,移植emWin图形界面库为GUI提供支持。实际运用证明,低成本液晶触摸屏运行稳定,界面设计便捷。%This paper provides a Iow-cost LCD Touch Screen design which use LPC1788 as the processor.LPC1788 which is de-signed by NXP,is a SoC based on Cortex-M3 CPU and contains a buiId-in LCD controI er,and introduces the interface of 4-wire resistive touch pad with LPC1788.In addition,transpIant the graphicaI interface Iibrary emWin to provide best support for the design of GUI.The practicaI appIication shows this screen works stabIy and makes the interface design convenient.

  9. 基于ARM Cortex M3内核TFT触摸屏无线遥控设计%On Wireless Remote Control System Design Based on the ARM Cortex M3 core TFT Touch Screen

    Institute of Scientific and Technical Information of China (English)

    李金赐; 梁九兴

    2012-01-01

    The designing is based on Bluetooth communication through the ARM Contex M3 core microprocessor STM32F103VET6 and TEF color LCD touch screen to design a touch-screen remote control.This kind of remote control,through touching the controls displayed on the TFT color LCD of the host computer,triggers variety of control signals and then wireless Bluetooth module sends control signals.%本设计是建立在蓝牙通信下通过ARM Cortex M3内核的微处理器STM32F103VET6与TFT彩色液晶触摸屏来设计一种触摸屏遥控器。该遥控器通过触摸上位机TFT彩色液晶触摸屏上显示的各个控件来触发各种控制信号;无线蓝牙模块发送各种控制信号。

  10. Design and Realization of GUI Based on ARM Cortex-M3%基于ARM Cortex-M3的图形用户界面设计和实现

    Institute of Scientific and Technical Information of China (English)

    韩定

    2015-01-01

    采用基于Cortex-M3内核的LPC1788为主控芯片和320(RGB)*480 pixels的带触摸点阵液晶屏,应用emWin图形库设计了一款简单易用的小型人机交互界面,并提供大容量的图片存储空间和可扩展字库存储空间,便于用户使用,可以广泛应用于家庭自动化和工业控制领域。%The ARM Cortex-M3 kernel processor LPC1788 and 320*480 pixels LCD with touch is used to design a small Graphical User Interface. EmWin is a kind of open source software, which is used to GUI embedded system. It can be widely used in home automation and industrial control.

  11. 年产5000m3意杨LVL主材及设备量的计算与配置%Calculation and Configuration of Main Material and Equipment Quantity for Annual 5000m3 Populus LVL

    Institute of Scientific and Technical Information of China (English)

    蒋瞻

    2012-01-01

      LVL has become the fastest kind of wooden composite material product in the current woodworking industry. The configuration of materials and equipment of an enterprise located in Northern Jiangsu that manufactures 5000 m 3 Populus LVL annually is introduced, with emphasis placed on relevant design calculation and configuration of such main materials as veneer and adhesive and such main equipment as presses, with the aim to provide reference for China’s small and medium-sized plywood manufacturing enterprises in term of design of the materials and equipment for manufacturing Populus LVL products.%  LVL已成为当今木材加工行业发展速度最快的一种木质复合材料产品。介绍了苏北一家年产5000m3意杨LVL企业的加工材料与设备配置情况,着重对单板、胶黏剂主材及压机等主要设备进行了相关的设计计算与配置,为我国制造胶合板的中小型企业做好意杨LVL产品的主材及其设备的设计工作提供参考。

  12. DISCUSSION ABOUT HEAT BALANCE CALCULATION AND ENERGY SAVING FOR 2500 m3 BLAST FURNACE%承钢2500 m3高炉热平衡测算与节能探讨

    Institute of Scientific and Technical Information of China (English)

    王秀英

    2014-01-01

    以承钢3座2 500 m3高炉为研究对象,用第一总热平衡测试法进行了高炉热平衡测算.结果表明:承钢2 500 m3高炉近年来节能主要是降低了冷却软熔带带走热量约0.29 GJ/tFe,减少煤气带走热量约0.12 GJ/tFe,降低瓦斯灰带走热量约0.04 GJ/tFe.从测算结果可以看出,因高炉工艺优化吨铁耗风量降低后,收入项中热风带入的热量减少约0.4 GJ/tFe,碳素氧化带入的热量减少约0.12 GJ/tFe.介绍了承钢高炉近年采用的节能技术及应用效果,根据热平衡测算结果和目前的前沿节能技术,提出了承钢高炉进一步降低能耗的措施.

  13. Rectangular spectral collocation

    KAUST Repository

    Driscoll, Tobin A.

    2015-02-06

    Boundary conditions in spectral collocation methods are typically imposed by removing some rows of the discretized differential operator and replacing them with others that enforce the required conditions at the boundary. A new approach based upon resampling differentiated polynomials into a lower-degree subspace makes differentiation matrices, and operators built from them, rectangular without any row deletions. Then, boundary and interface conditions can be adjoined to yield a square system. The resulting method is both flexible and robust, and avoids ambiguities that arise when applying the classical row deletion method outside of two-point scalar boundary-value problems. The new method is the basis for ordinary differential equation solutions in Chebfun software, and is demonstrated for a variety of boundary-value, eigenvalue and time-dependent problems.

  14. Spectral disentangling with Spectangular

    Science.gov (United States)

    Sablowski, Daniel P.; Weber, Michael

    2017-01-01

    The paper introduces the software Spectangular for spectral disentangling via singular value decomposition with global optimisation of the orbital parameters of the stellar system or radial velocities of the individual observations. We will describe the procedure and the different options implemented in our program. Furthermore, we will demonstrate the performance and the applicability using tests on artificial data. Additionally, we use high-resolution spectra of Capella to demonstrate the performance of our code on real-world data. The novelty of this package is the implemented global optimisation algorithm and the graphical user interface (GUI) for ease of use. We have implemented the code to tackle SB1 and SB2 systems with the option of also dealing with telluric (static) lines. Based in part on data obtained with the STELLA robotic telescope in Tenerife, an AIP facility jointly operated by AIP and IAC.

  15. Spectral Animation Compression

    Institute of Scientific and Technical Information of China (English)

    Chao Wang; Yang Liu; Xiaohu Guo; Zichun Zhong; Binh Le; Zhigang Deng

    2015-01-01

    This paper presents a spectral approach to compress dynamic animation consisting of a sequence of homeomor-phic manifold meshes. Our new approach directly compresses the field of deformation gradient defined on the surface mesh, by decomposing it into rigid-body motion (rotation) and non-rigid-body deformation (stretching) through polar decompo-sition. It is known that the rotation group has the algebraic topology of 3D ring, which is different from other operations like stretching. Thus we compress these two groups separately, by using Manifold Harmonics Transform to drop out their high-frequency details. Our experimental result shows that the proposed method achieves a good balance between the reconstruction quality and the compression ratio. We compare our results quantitatively with other existing approaches on animation compression, using standard measurement criteria.

  16. Spectral disentangling with Spectangular

    CERN Document Server

    Sablowski, Daniel P

    2016-01-01

    The paper introduces the software Spectangular for spectral disentangling via singular value decomposition with global optimisation of the orbital parameters of the stellar system or radial velocities of the individual observations. We will describe the procedure and the different options implemented in our program. Furthermore, we will demonstrate the performance and the applicability using tests on artificial data. Additionally, we use high-resolution spectra of Capella to demonstrate the performance of our code on real-world data. The novelty of this package is the implemented global optimisation algorithm and the graphical user interface (GUI) for ease of use. We have implemented the code to tackle SB1 and SB2 systems with the option of also dealing with telluric (static) lines.

  17. Spectral proper orthogonal decomposition

    CERN Document Server

    Sieber, Moritz; Paschereit, Christian Oliver

    2015-01-01

    The identification of coherent structures from experimental or numerical data is an essential task when conducting research in fluid dynamics. This typically involves the construction of an empirical mode base that appropriately captures the dominant flow structures. The most prominent candidates are the energy-ranked proper orthogonal decomposition (POD) and the frequency ranked Fourier decomposition and dynamic mode decomposition (DMD). However, these methods fail when the relevant coherent structures occur at low energies or at multiple frequencies, which is often the case. To overcome the deficit of these "rigid" approaches, we propose a new method termed Spectral Proper Orthogonal Decomposition (SPOD). It is based on classical POD and it can be applied to spatially and temporally resolved data. The new method involves an additional temporal constraint that enables a clear separation of phenomena that occur at multiple frequencies and energies. SPOD allows for a continuous shifting from the energetically ...

  18. SPECTRAL ANALYSIS OF RADIOXENON

    Energy Technology Data Exchange (ETDEWEB)

    Cooper, Matthew W.; Bowyer, Ted W.; Hayes, James C.; Heimbigner, Tom R.; Hubbard, Charles W.; McIntyre, Justin I.; Schrom, Brian T.

    2008-09-23

    Monitoring changes in atmospheric radioxenon concentrations is a major tool in the detection of an underground nuclear explosion. Ground based systems like the Automated Radioxenon Sampler /Analyzer (ARSA), the Swedish Unattended Noble gas Analyzer (SAUNA) and the Automatic portable radiometer of isotopes Xe (ARIX), can collect and detect several radioxenon isotopes by processing and transferring samples into a high efficiency beta-gamma coincidence detector. The high efficiency beta-gamma coincidence detector makes these systems highly sensitive to the radioxenon isotopes 133Xe, 131mXe, 133mXe and 135Xe. The standard analysis uses regions of interest (ROI) to determine the amount of a particular radioxenon isotope present. The ROI method relies on the peaks of interest falling within energy limits of the ROI. Some potential problems inherent in this method are the reliance on stable detector gains and a fixed resolution for each energy peak. In addition, when a high activity sample is measured there will be more interference among the ROI, in particular within the 133Xe, 133mXe, and 131mXe regions. A solution to some of these problems can be obtained through spectral fitting of the data. Spectral fitting is simply the fitting of the peaks using known functions to determine the number and relative peak positions and widths. By knowing this information it is possible to determine which isotopes are present. Area under each peak can then be used to determine an overall concentration for each isotope. Using the areas of the peaks several key detector characteristics can be determined: efficiency, energy calibration, energy resolution and ratios between interfering isotopes (Radon daughters).

  19. Scale-up of industrial biodiesel production to 40 m(3) using a liquid lipase formulation.

    Science.gov (United States)

    Price, Jason; Nordblad, Mathias; Martel, Hannah H; Chrabas, Brent; Wang, Huali; Nielsen, Per Munk; Woodley, John M

    2016-08-01

    In this work, we demonstrate the scale-up from an 80 L fed-batch scale to 40 m(3) along with the design of a 4 m(3) continuous process for enzymatic biodiesel production catalyzed by NS-40116 (a liquid formulation of a modified Thermomyces lanuginosus lipase). Based on the analysis of actual pilot plant data for the transesterification of used cooking oil and brown grease, we propose a method applying first order integral analysis to fed-batch data based on either the bound glycerol or free fatty acid content in the oil. This method greatly simplifies the modeling process and gives an indication of the effect of mixing at the various scales (80 L to 40 m(3) ) along with the prediction of the residence time needed to reach a desired conversion in a CSTR. Suitable process metrics reflecting commercial performance such as the reaction time, enzyme efficiency, and reactor productivity were evaluated for both the fed-batch and CSTR cases. Given similar operating conditions, the CSTR operation on average, has a reaction time which is 1.3 times greater than the fed-batch operation. We also showed how the process metrics can be used to quickly estimate the selling price of the enzyme. Assuming a biodiesel selling price of 0.6 USD/kg and a one-time use of the enzyme (0.1% (w/woil ) enzyme dosage); the enzyme can then be sold for 30 USD/kg which ensures that that the enzyme cost is not more than 5% of the biodiesel revenue. Biotechnol. Bioeng. 2016;113: 1719-1728. © 2016 Wiley Periodicals, Inc.

  20. Theoretical study of neutral and charged Sc{sub n{<=}2}-(benzene){sub m{<=}3} clusters

    Energy Technology Data Exchange (ETDEWEB)

    Maynez-Rojas, Miguel; Castro, Miguel, E-mail: castro@quetzal.pquim.unam.mx [Universidad Nacional Autonoma de Mexico, Departamento de Fisica y Quimica Teorica, DEPg. Facultad de Quimica (Mexico)

    2013-01-15

    Interactions of benzene molecules with scandium atoms, Sc{sub n{<=}2}-(C{sub 6}H{sub 6}){sub m{<=}3}, in the gas phase were studied by means of density functional theory. All-electron calculations were performed using the B3LYP hybrid functional in concert with 6-311+G(d,p) orbital basis sets for the Sc, C, and H atoms. Multiple-decker sandwich (MDS) structures are identified as the ground states for Sc{sub n{<=}2}-(C{sub 6}H{sub 6}){sub m{<=}3}, where the ligands are attached to the metal through Sc-C bonding, formed between the 3d electrons and the {pi}-clouds of the benzene rings. Significant distortion is produced on the absorbed benzene molecules by the metal-ligand bonding. Rice ball structures also appeared, but they were found at higher energies, in such a way that essentially MDS isomers may emerge in the molecular beams. Even the low number of valence electrons (3d{sup 2}4s{sup 1}) of the Sc atom; sextuple coordinations are formed, but they show different Sc-C bond lengths, diminishing the symmetry of neutral and charged clusters. The estimated ionization energies, in near agreement with experimental data, and electron affinities, suggest delocalization of the valence electrons through the network of 3d-{pi} bonds of Sc{sub 1,2}-(C{sub 6}H{sub 6}){sub m{<=}3}. The binding energies decrease with the absorption of more benzene molecules, and in some cases increase as more metal atoms are added to the cluster.

  1. Adsorption of aromatics on the (111) surface of PtM and PtM3 (M = Fe, Ni) alloys

    Energy Technology Data Exchange (ETDEWEB)

    Hensley, Alyssa; Schneider, Sebastian; Wang, Yong; McEwen, Jean-Sabin

    2015-09-18

    The adsorption of benzene and phenol was studied on PtM and PtM3 (111) surfaces, with M being either Ni or Fe. Under vacuum, the most favorable near surface structures showed an enrichment in Pt over the M species. An analysis of the electronic structure of the metal species in the clean surfaces with different near surface structures was done with the d-band model and showed that the Pt's d-states are significantly shifted away from the Fermi level due to the Pt-M interactions while the M species' d-states were less affected, with Ni's d-band shifting closer to the Fermi level and Fe's d-band shifting away from the Fermi level. The adsorption of aromatics, benzene and phenol, on several near surface structures for the PtM and PtM3 (111) surfaces showed that higher surface M concentrations resulted in a stronger adsorption due to the larger amount of charge transferred between the adsorbate and surface. However, compared to the adsorption of benzene and phenol on monometallic surfaces, the adsorption of these species on the PtM and PtM3 (111) surfaces was significantly weakened. Overall, our results show that the observed behavior of these Pt/Fe and Pt/Ni alloys is similar to that seen for the previously studied Pd/Fe surfaces. Furthermore, balancing the weakly adsorbing Pt surface species with the more strongly interacting Fe or Ni species can lead to the tailored adsorption of aromatics with applications in both hydrodeoxygenation and hydrogenation reactions by increasing the desorption rate of wanted aromatic products.

  2. Syntheses, crystal structure and magnetic properties of Rm+nCo5m+3nB2n

    Institute of Scientific and Technical Information of China (English)

    梁敬魁; 陈怡; 陈小龙

    2001-01-01

    The phase relations at the 600℃ and 700℃ isothermal sections of the ternary systems R-Co-B for R= Nd, Pr and R = Sm, Gd respectively were summarized in this paper. For Rm+ n Co5m+3n B2n, two new types ofcompounds R3Co13B2(R=Pr, Nd, Sm, Gd, Dy, Ho, Er, Y) (m=2, n=1) andR5Co19B6(R=Pr, Nd) (m=2,n = 3 ) were synthesized by utilizing the principle of structural combination. Their crystalstructures and easymagnetization direction were determined by X-ray powder diffraction, and structures were refined by the Rietveldmethod. The Curie temperature Tc, saturation magnetization M8 and anisotropic field HA of the new compounds weremeasured using a vibrating-sample magnetometer, an extraction sample magnetometer and M(H) - H curves of samplesin different magnetization directions respectively. The Tc and Ms of Rm + n Co5 m + 3 n B2n increase with increasing values of mat a given n value. HA increases with an increase in n when m is kept invariable. The effects of the substitution of Ni for Co on the magnetic properties of Nd13 Co15- x Nix B2 were also investigated. It was found that TsR decreased monotonously as the concentration of Ni increased, and at x = 3 the easy magnetization direction becomes axial at room temperature. The relations between crystal structure and magnetic properties of Rm + nCo5m+ 3nB2n and the possible routes of synthesizing permanent magnetic materials are also discussed.

  3. Single-hole spectral function and spin-charge separation in the t-J model

    Science.gov (United States)

    Mishchenko, A. S.; Prokof'ev, N. V.; Svistunov, B. V.

    2001-07-01

    Worm algorithm Monte Carlo simulations of the hole Green function with subsequent spectral analysis were performed for 0.1hole spectral function in the thermodynamic limit. Spectral analysis reveals a δ-function-sharp quasiparticle peak at the lower edge of the spectrum that is incompatible with the power-law singularity and thus rules out the possibility of spin-charge separation in this parameter range. Spectral continuum features two peaks separated by a gap ~4÷5 t.

  4. Successful management of pulmonary hemorrhage and aspergillosis in a patient with acute myeloid leukemia (AML-M3

    Directory of Open Access Journals (Sweden)

    Hulya Gunbatar

    2015-01-01

    Full Text Available A 35-year-old man presented with a one month history of gingival bleeding. He was diagnosed with Acute Myeloid Leukemia (AML-M3. During treatment he developed alveolar hemorrhage for which he was treated with a steroid. After the steroid treatment he developed a nodule, a cavitary lesion and atelectasia in the left lung. He was treated with voriconazole. After therapy with voriconazole his lesion significantly decreased. This case illustrates the efficacy and safety of antifungal therapy with voriconazole for aspergillosis complicated by AML.

  5. Successful management of pulmonary hemorrhage and aspergillosis in a patient with acute myeloid leukemia (AML-M3).

    Science.gov (United States)

    Gunbatar, Hulya; Demir, Cengiz; Kara, Erdal; Esen, Ramazan; Sertogullarindan, Bunyamin; Asker, Selvi

    2015-01-01

    A 35-year-old man presented with a one month history of gingival bleeding. He was diagnosed with Acute Myeloid Leukemia (AML-M3). During treatment he developed alveolar hemorrhage for which he was treated with a steroid. After the steroid treatment he developed a nodule, a cavitary lesion and atelectasia in the left lung. He was treated with voriconazole. After therapy with voriconazole his lesion significantly decreased. This case illustrates the efficacy and safety of antifungal therapy with voriconazole for aspergillosis complicated by AML.

  6. Spectral unmixing: estimating partial abundances

    CSIR Research Space (South Africa)

    Debba, Pravesh

    2009-01-01

    Full Text Available of spectral unmixing 3 End-member spectra and synthetic mixtures 4 Results 5 Conclusions Debba (CSIR) Spectral Unmixing LQM 2009 2 / 22 Background and Research Question If research could be as easy as eating a chocolate cake . . . Figure: Can you guess... the ingredients for this chocolate cake? Debba (CSIR) Spectral Unmixing LQM 2009 3 / 22 Background and Research Question Ingredients Quantity unsweetened chocolate unsweetened cocoa powder boiling water flour baking powder baking soda salt unsalted...

  7. Spectral Signatures of Surface Materials in Pig Buildings

    DEFF Research Database (Denmark)

    Zhang, GuoQiang; Strøm, Jan; Blanke, Mogens

    2006-01-01

    and after high-pressure water cleaning. The spectral signatures of the surface materials and dirt attached to the surfaces showed that it is possible to make discrimination and hence to classify areas that are visually clean. When spectral bands 450, 600, 700 and 800 nm are chosen, there are at least two...... the cleaning process and to minimise the amount of water and electricity consumed. This research is aimed at utilising a spectral imaging method for cleanliness detection. Consequently, information on the reflectance of building materials and contamination in different spectral ranges is important...... in the investigation. Reflectance data were sampled under controlled lighting conditions using a spectrometer communicating with a portable computer. The measurements were performed in a laboratory with materials used in a pig house for 4-5 weeks. The spectral data were collected for the surfaces before, during...

  8. White light spectral interferometry as a spectrometer calibration tool.

    Science.gov (United States)

    de la Fuente, Raúl

    2014-01-01

    For this paper, we used a white light interferometer in combination with spectral lamps to perform the wavelength calibration of a dispersive spectrometer. Illuminating the spectrometer with suitable spectral lamps gives the wavelength-pixel number relationship at discrete positions of the spectrometer detector array, and the wavelength-dependent phase difference at the output of the white light interferometer allows for a complete spectral calibration at any point on the detector (i.e., for every wavelength in the spectral range of the spectrometer). The details of this new calibration procedure are discussed, and two practical examples exhibiting the robustness of the method are presented. In addition, certain issues relating to minimizing the number of spectral lines used in the calibration procedure are examined.

  9. Quantitative Analysis of Spectral Impacts on Silicon Photodiode Radiometers: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Myers, D. R.

    2011-04-01

    Inexpensive broadband pyranometers with silicon photodiode detectors have a non-uniform spectral response over the spectral range of 300-1100 nm. The response region includes only about 70% to 75% of the total energy in the terrestrial solar spectral distribution from 300 nm to 4000 nm. The solar spectrum constantly changes with solar position and atmospheric conditions. Relative spectral distributions of diffuse hemispherical irradiance sky radiation and total global hemispherical irradiance are drastically different. This analysis convolves a typical photodiode response with SMARTS 2.9.5 spectral model spectra for different sites and atmospheric conditions. Differences in solar component spectra lead to differences on the order of 2% in global hemispherical and 5% or more in diffuse hemispherical irradiances from silicon radiometers. The result is that errors of more than 7% can occur in the computation of direct normal irradiance from global hemispherical irradiance and diffuse hemispherical irradiance using these radiometers.

  10. Snapshot Raman Spectral Imager

    Science.gov (United States)

    2010-03-31

    range is appealing in this regard as upper atmospheric absorption by oxygen and ozone eliminate almost all radiation in the Raman shifted range of a...customer wanted to replace a bulky Fourier-Transform Infrared ( FTIR ) system with a dispersive system to lower the cost and size of the instrument. AQT

  11. [Review of digital ground object spectral library].

    Science.gov (United States)

    Zhou, Xiao-Hu; Zhou, Ding-Wu

    2009-06-01

    A higher spectral resolution is the main direction of developing remote sensing technology, and it is quite important to set up the digital ground object reflectance spectral database library, one of fundamental research fields in remote sensing application. Remote sensing application has been increasingly relying on ground object spectral characteristics, and quantitative analysis has been developed to a new stage. The present article summarized and systematically introduced the research status quo and development trend of digital ground object reflectance spectral libraries at home and in the world in recent years. Introducing the spectral libraries has been established, including desertification spectral database library, plants spectral database library, geological spectral database library, soil spectral database library, minerals spectral database library, cloud spectral database library, snow spectral database library, the atmosphere spectral database library, rocks spectral database library, water spectral database library, meteorites spectral database library, moon rock spectral database library, and man-made materials spectral database library, mixture spectral database library, volatile compounds spectral database library, and liquids spectral database library. In the process of establishing spectral database libraries, there have been some problems, such as the lack of uniform national spectral database standard and uniform standards for the ground object features as well as the comparability between different databases. In addition, data sharing mechanism can not be carried out, etc. This article also put forward some suggestions on those problems.

  12. The Horizontal Branch in the UV Colour Magnitude Diagrams. II. The case of M3, M13 and M79

    CERN Document Server

    Dalessandro, Emanuele; Ferraro, Francesco R; Mucciarelli, Alessio; Cassisi, Santi

    2012-01-01

    We present a detailed comparison between far-UV/optical colour Magnitude Diagrams obtained with high-resolution Hubble Space Telescope data and suitable theoretical models for three Galactic Globular Clusters: M3, M13 and M79. These systems represents a classical example of clusters in the intermediate metallicity regime that, even sharing similar metal content and age, show remarkably different Horizontal Branch morphologies. As a consequence, the observed differences in the colour distributions of Horizontal Branch stars cannot be interpreted in terms of either first (metallicity) or a second parameter such as age. We investigate here the possible role of variations of initial Helium abundance (Y). Thanks to the use of a proper setup of far-UV filters, we are able to put strong constraints on the maximum Y (Y_{max}) values compatible with the data. We find differences Delta Y_{max} ~ 0.02-0.04 between the clusters with M13 showing the largest value (Y_{max} ~ 0.30) and M3 the smallest (Y_{max} ~ 0.27). In g...

  13. 安钢10万m3威金斯气柜利用效率探讨与应用%Efficiency Analysis and Application of Anyang Iron and Steel 100 000 m3 Wiggins Gasholder

    Institute of Scientific and Technical Information of China (English)

    于海顺; 王志峰; 王祥凯; 张文杰; 赵卫兵

    2015-01-01

    As to the operating situation of Augang 100 000 Wiggins gas holder, this paper analyzes the efficiency factors of Wiggins gesholder, and puts forward improving weasuers, including establishing a liaision mechauism, adjusting part programs of micro oxygen analzer before gasholder in gasholder control system to improve the gas-holder efficiency.%针对安钢10万m3威金斯气柜运行现状,对影响威金斯气柜利用效率的因素进行了探讨,并提出了建立联络机制、调整气柜控制系统中气柜进口前微氧分析仪的部分程序等改进措施。采取有效措施后提高了气柜的利用效率。

  14. Spectral selectivity in optical fiber capillary dye lasers.

    Science.gov (United States)

    Mobini, Esmaeil; Abaie, Behnam; Peysokhan, Mostafa; Mafi, Arash

    2017-05-01

    We explore the spectral properties of a capillary dye laser in the highly multimode regime. Our experiments indicate that the spectral behavior of the laser does not conform to a simple Fabry-Perot (FP) analysis; rather, it is strongly dictated by a Vernier resonant mechanism involving multiple modes, which propagate with different group velocities. The laser operates over a very broad spectral range and the Vernier effect gives rise to a free spectral range, which is orders of magnitude larger than that expected from a simple FP mechanism. The theoretical calculations presented confirm the experimental results. Propagating modes of the capillary fiber are calculated using the finite-element method and it is shown that the optical path lengths resulting from simultaneous beatings of these modes are in close agreement with the optical path lengths directly extracted from the Fourier transform of the experimentally measured laser emission spectra.

  15. 高铝渣对济钢3200m3高炉冶炼的影响%Influence of High Al2O3 Slag on Operation of 3 200 m3 BF in Jinan Steel

    Institute of Scientific and Technical Information of China (English)

    王军

    2015-01-01

    To the characteristics of high Al2O3 slag with higher viscosity, poor liquidity, and poor desulphurization ability, by adjusting the thermal system and distributing system, the Mg/Al ratio in the slag is controlled lager than 0.6 by increasing the MgO content in sintering, the MgO content in the slag is made between 8%-11%, the overall operation of 3 200 m3 BF in Jinan Steel can fit smelting requirement with high Al2O3 slag. Under the condition of slag ratio increase by 43 kg/t, the silicon in the pig iron was decreased, the desulphurization ability of the slag was strengthened and third grade iron was eliminated basically.%针对高铝渣特有的黏度高、流动性差、脱硫能力差的特点,济钢3 200 m3高炉通过调整热制度和布料制度,在烧结时提高MgO含量,控制渣中镁铝比>0.6,使渣中MgO含量在8%~11%,高炉的整体操作炉型适应了高铝渣的冶炼要求.在渣铁比升高43 kg/t的条件下,高炉生铁含硅降低,炉渣脱硫能力增强,基本杜绝了三类铁.

  16. New Technology Adopted and Operation Practice in No.3 3 200 m3 BF in Laiwu Steel%莱钢3#3200 m3高炉采用的新技术及生产实践

    Institute of Scientific and Technical Information of China (English)

    贾利军; 孟淑敏; 王冰

    2016-01-01

    In the paper, a series of new process and technology adopted in newly built No.3 3 200 m3 BF in laiwu steel are introduced, such as comprehensive technology of blast furnace longevity,multi nozzle type and fixed hopper of PW bell-less top, technology of axial cyclone deduster plus automatically discharging ash system, environmental INBA slag granulation technology, the dehumidified blast technology of BF and so on. The blast furnace was started up smoothly and reached the design product, in addition, all kinds of operation experience was happened, for example, intensified smelting, high coal ratio, large ore batch, limited production, wind-off without plan. The results were verified that every system ran normally and had better technical and economic index.%介绍了莱钢3#3200 m3高炉采用的长寿综合技术、多流嘴式料流分配器+固定料罐的PW无料钟炉顶设备、轴流旋风除尘器+吸排罐车自动卸灰系统、环保型INBA法渣处理技术、高炉脱湿鼓风技术等设计特点,高炉顺利开炉达产,历经强化冶炼、高煤比、大矿批、限产、无计划休风等不同操作实践,炉况顺行良好,各工艺系统运行正常,取得了良好的技术经济指标。

  17. Portable and Smart Ultrasonic Fluid Level Meter Based on ARM Cortex- M3%基于ARM Cortex - M3便携式智能超声波液位计

    Institute of Scientific and Technical Information of China (English)

    张根宝; 李秀平; 庞苏娟

    2012-01-01

    为了准确测量环境恶劣工业生产中的液位以保证生产效率,通过研究超声波测距工作原理,采用新型高性能、低功耗和低成本的ARM - Cortex M3内核微控制器,结合超声波技术、红外传输与DS1820温度补偿修正设计了一款便携式智能超声波液位计.其采用的先进微处理器以及无线传输的方式,简化了硬件电路,优化了软件编程.研究表明:该液位计设计提高了液位测量精度、实时性、灵活性与快速性.%To measure fluid level in poor industrial production conditions accurately for ensuring production efficiency,a portable intelligent correction ultrasonic fluid level meter was designed by studying the working principle of ultrasonic distance measurement. New high-performance, low power and low-cost ARM-Cortex M3 microcontroller core, combined with ultrasonic technology, infrared transmission and DS1820 temperature compensation were used in the level meter. The use of advanced microprocessor and wireless transmission, simplified hardware and optimized software programming. Studies show that the design of this fluid level gauge improved accuracy,timeliness,flexibility and rapidity of the level measurement.

  18. 莱钢3号3200 m3高炉设计创新与实践%Design innovation and practice of No. 3200 m3 BF in Laigang

    Institute of Scientific and Technical Information of China (English)

    王冰; 孟淑敏; 贾利军

    2016-01-01

    莱钢3号3200m3高炉设计采用了串罐无料钟炉顶、软水密闭循环冷却、炉体全覆盖冷却壁、铜冷却壁、 UCAR热压小块炭砖、改进型顶燃式热风炉、环保型INBA渣处理、轴流式旋风除尘器、环保平坦化出铁场、全干法布袋除尘、高富氧喷煤等一系列先进实用、成熟可靠、清洁环保、高效长寿的新技术设备,为实现高炉“高效、优质、低耗、长寿、环保”的目标打下了坚实的基础。%A series of advanced and suitable , mature and reliable , clean and environmentally friendly, high efficiency and long campaign techniques were adopted in the design of No. 3 3200m3 BF in Laiwu Steel, such as BLT, closed loop soft water cooling, complete coverage of furnace body cooling stave, copper cooling staves, UCAR hot pressing small pieces of carbon brick, improved top combus-tion hot blast stove, environmental friendly INBA slag treatment, axial cyclone deduster, green flat cast house, completely dry method bag deduster, high oxygen enrichment PCI, all the new technolo-gies mentioned above has laid a solid foundation for blast the target of high efficiency, high quality, low consumption, long campaign and clean environmental protection.

  19. Hearth Erosion Situation Analysis for the 1 750 m3 Blast Furnace in Jinan Steel%济钢1750 m3高炉炉缸侵蚀情况分析

    Institute of Scientific and Technical Information of China (English)

    张小伟; 张熙玮

    2015-01-01

    通过对生产条件及炉缸结构相同的济钢1#、3#1750 m3高炉炉缸侵蚀情况进行调查,发现1#高炉炉缸呈浅锅底—象脚状侵蚀,扒炉实测表明,炉缸、炉底交接处侵蚀最为严重,炭砖残存厚度最薄处仅为300 mm;3#高炉铁口附近炭砖出现不同程度裂纹,侵蚀严重处炭砖残存厚度600 mm。建议考虑炭砖的微孔度,使用高可靠性热电偶,降低炉底冷却水流量,增加炉缸冷却水流量等,以提高高炉寿命。%The hearth erosion of Jinan Steel’s No.1 and No.3 1 750 m3 BF have been investigated, although they have the same production conditions and hearth structure. It is found that the No.1 blast furnace hearth pale pot is like the foot-shaped erosion, griddle test shows junction of hearth and bottom are the most serious erosion position, the remaining thickness of the thinnest carbon brick is only 300 mm. The carbon bricks near the iron mouth of the No.3 BF have cracked to some extent, the remaining carbon brick thickness of severe erosion is 600 mm. To improve and prolong the life of the blast furnace, it is suggested that to apply the porous carbon bricks and high reliability thermocouples, reduce the cooling water flow for bottom, increase the cooling water flow of the hearth etc.

  20. Design of on-broad diagnose terminal with real-time warning based on CORTEX-M3%基于CORTEX-M3的实时车载诊断预警系统的设计

    Institute of Scientific and Technical Information of China (English)

    陈鲤文; 邹复民

    2013-01-01

    The design of ODB-II standard framework is based on embedded real-time operation and it can be realized on Cortex-M3 CPU core with uc/os II operating system. We have successful read real-time OBD-II data of vehicles from PC monitor and gather accident codes and sensor data through CAN bus, which can be used to evaluate the health of the automobiles, preventive against trouble, deduce the cost of driving and improve the driving safety. The advantage to the device is taking full account of all sorts of vehicle buses and put forward a kind of resolved scheme about remote on-boarded diagnosis in complicated vehicle circumstance.%基于嵌入式实时操作系统的OBD-Ⅱ诊断协议框架,以Cortex-M3为内核,采用uc/os Ⅱ操作系统实现了ISO15765协议,成功通过CAN总线读取了车辆的OBD-Ⅱ系统数据,通过上位机监控窗口,能实时检查汽车故障码与汽车传感器数据.可在此基础上评价汽车健康状况,并可对故障及早预防,降低行车成本,提供行车安全性;本设计充分考虑中国汽车市场主流总线发展的情况,提供了在复杂的车载环境下远程车载诊断设备的解决方案.

  1. Miniaturized spectral imager for Aalto-1 nanosatellite

    Science.gov (United States)

    Mannila, Rami; Näsilä, Antti; Praks, Jaan; Saari, Heikki; Antila, Jarkko

    2011-11-01

    The Aalto-1 is a 3U-cubesat project coordinated by Aalto University. The satellite, Aalto-1, will be mainly built by students as project assignments and thesis works. VTT Technical Research Centre of Finland will develop the main Earth observation payload, a miniaturized spectral imager, for the satellite. It is a novel highly miniaturized tunable filter type spectral imager. Mass of the spectral imager will be less than 400 grams, and dimensions will be approximately 80 mm x 80 mm x 45 mm. The spectral imager is based on a tunable Fabry-Pérot interferometer (FPI) accompanied by an RGB CMOS image sensor. The FPI consists of two highly reflective surfaces separated by a tunable air gap and it is based either on a microelectromechanical (MEMS) or piezo-actuated structure. The MEMS FPI is a monolithic device, i.e. it is made entirely on one substrate in a batch process, without assembling separate pieces together. The gap is adjusted by moving the upper mirror with electrostatic force. Benefits of the MEMS FPI are low mass and small size. However, large aperture (2-10 mm) MEMS FPIs are currently under development, thus it is not yet known if their performance is adequate. The piezo-actuated FPI uses three piezo-actuators and is controlled in a closed capacitive feedback loop. The drawback of the piezo-actuated FPI is its higher mass. However, it has a large aperture which enables a shorter exposure times. Selection of the FPI type will be done after thorough evaluation. Depending on the selected FPI type, the spectral resolution of the imager will be 5 - 10 nm at full width at half maximum and it will operate in the visible and/or near infrared range.

  2. THE INFLUENCE OF THE INGOT MOLD COOLING ON THE STRUCTURE OF SILUMINA CASTINGS AK15M3 AT VERTICAL CENTRIFUGAL CASTING

    Directory of Open Access Journals (Sweden)

    V. Yu. Stecenko

    2013-01-01

    Full Text Available Influence of ways of the mold cooling on structure of castings with diameter of 135 mm from AK15M3 silumin at vertical centrifugal casting is investigated. It is established that for production of castings with diameter 135 mm from AK15M3 silumin with high mechanical and tribotechnical properties it is necessary to apply a shaped mould with water-spray cooling at expense of cooler of 0,42 m3/h.

  3. Spectral Analysis of Markov Chains

    OpenAIRE

    2007-01-01

    The paper deals with the problem of a statistical analysis of Markov chains connected with the spectral density. We present the expressions for the function of spectral density. These expressions may be used to estimate the parameter of the Markov chain.

  4. SPECTRAL ANALYSIS OF EXCHANGE RATES

    Directory of Open Access Journals (Sweden)

    ALEŠA LOTRIČ DOLINAR

    2013-06-01

    Full Text Available Using spectral analysis is very common in technical areas but rather unusual in economics and finance, where ARIMA and GARCH modeling are much more in use. To show that spectral analysis can be useful in determining hidden periodic components for high-frequency finance data as well, we use the example of foreign exchange rates

  5. Miniature spectrally selective dosimeter

    Energy Technology Data Exchange (ETDEWEB)

    Adams, R.R.; Macconochie, I.O.; Poole, B.D.

    1983-02-08

    The present invention discloses a miniature spectrally selective dosimeter capable of measuring selected bandwidths of radiation exposure on small mobile areas. This is achieved by the combination of photovoltaic detectors, electrochemical integrators (e-cells) and filters in a small compact case which can be easily attached in close proximity to and substantially parallel to the surface being measured. In one embodiment two photovoltaic detectors, two e-cells and three filters are packaged in a small case with attaching means consisting of a safety pin. In another embodiment, two detectors, one e-cell and three filters are packaged in a small case with attaching means consisting of a clip to clip over a side piece of an eye glass frame in a further embodiment, the electro-optic elements a packaged in a wristwatch case with attaching means being a watchband. The filters in all embodiments allow only selected wavelengths of radiation to be detected by the photovoltaic detectors and then integrated by the e-cells.

  6. Spectral numbers in Floer theories

    CERN Document Server

    Usher, Michael

    2007-01-01

    The chain complexes underlying Floer homology theories typically carry a real-valued filtration, allowing one to associate to each Floer homology class a spectral number defined as the infimum of the filtration levels of chains representing that class. These spectral numbers have been studied extensively in the case of Hamiltonian Floer homology by Oh, Schwarz, and others. We prove that the spectral number associated to any nonzero Floer homology class is always finite, and that the infimum in the definition of the spectral number is always attained. In the Hamiltonian case, this implies that what is known as the "nondegenerate spectrality" axiom holds on all closed symplectic manifolds. Our proofs are entirely algebraic and rather elementary, and apply to any Floer-type theory (including Novikov homology) satisfying certain standard formal properties provided that one works with coefficients in a Novikov ring whose degree-zero part \\Lambda_0 is a field. The key ingredient is a theorem about linear transforma...

  7. The spectral irradiance traceability chain at PTB

    Science.gov (United States)

    Sperfeld, P.; Pape, S.; Nevas, S.

    2013-05-01

    international intercomparisons among NMIs. Ultimately, the spectral irradiance can be realized with expanded measurement uncertainties of far less than 1 % over a wide spectral range. Thus, for customers with high demands on low measurement uncertainties, it is possible to calibrate their working standards directly against the blackbody-radiator, taking into account the higher necessary effort. In special cases it is possible to calibrate the customer's spectroradiometric facilities directly in front of the blackbody-radiator. In the context of the European Metrology Research Project Traceability for surface spectral solar ultraviolet radiation, the traceability chain will be improved and adapted.

  8. The spectral irradiance traceability chain at PTB

    Energy Technology Data Exchange (ETDEWEB)

    Sperfeld, P.; Pape, S.; Nevas, S. [Physikalisch-Technische Bundesanstalt, Bundesallee 10, 381160 Braunschweig (Germany)

    2013-05-10

    confirmed by international intercomparisons among NMIs. Ultimately, the spectral irradiance can be realized with expanded measurement uncertainties of far less than 1 % over a wide spectral range. Thus, for customers with high demands on low measurement uncertainties, it is possible to calibrate their working standards directly against the blackbody-radiator, taking into account the higher necessary effort. In special cases it is possible to calibrate the customer's spectroradiometric facilities directly in front of the blackbody-radiator. In the context of the European Metrology Research Project Traceability for surface spectral solar ultraviolet radiation, the traceability chain will be improved and adapted.

  9. Spectral functions from anisotropic lattice QCD

    Energy Technology Data Exchange (ETDEWEB)

    Aarts, G.; Allton, C. [Department of Physics, Swansea University, Swansea SA2 8PP, Wales (United Kingdom); Amato, A. [Helsinki Institute of Physics and University of Helsinki, Helsinki (Finland); Evans, W. [Albert Einstein Center for Fundamental Physics, Institute for Theoretical Physics Universitat Bern, Sidlerstrasse 5, CH-3012 Bern (Switzerland); Giudice, P. [Institut für Theoretische Physik, Universität Münster, D–48149 Münster (Germany); Harris, T. [School of Mathematics, Trinity College, Dublin 2 (Ireland); Kelly, A. [Department of Mathematical Physics, Maynooth University, Maynooth, Co Kildare (Ireland); Kim, S.Y. [Department of Physics, Sejong University, Seoul 143-747 (Korea, Republic of); Lombardo, M.P. [INFN–Laboratori Nazionali di Frascati, I–00044 Frascati (RM) (Italy); Praki, K. [Department of Physics, Swansea University, Swansea SA2 8PP, Wales (United Kingdom); Ryan, S.M. [School of Mathematics, Trinity College, Dublin 2 (Ireland); Skullerud, J.-I. [Department of Mathematical Physics, Maynooth University, Maynooth, Co Kildare (Ireland)

    2016-12-15

    The FASTSUM collaboration has been carrying out lattice simulations of QCD for temperatures ranging from one third to twice the crossover temperature, investigating the transition region, as well as the properties of the Quark Gluon Plasma. In this contribution we concentrate on quarkonium correlators and spectral functions. We work in a fixed scale scheme and use anisotropic lattices which help achieving the desirable fine resolution in the temporal direction, thus facilitating the (ill posed) integral transform from imaginary time to frequency space. We contrast and compare results for the correlators obtained with different methods, and different temporal spacings. We observe robust features of the results, confirming the sequential dissociation scenario, but also quantitative differences indicating that the methods' systematic errors are not yet under full control. We briefly outline future steps towards accurate results for the spectral functions and their associated statistical and systematic errors.

  10. Spectral functions from anisotropic lattice QCD

    Science.gov (United States)

    Aarts, G.; Allton, C.; Amato, A.; Evans, W.; Giudice, P.; Harris, T.; Kelly, A.; Kim, S. Y.; Lombardo, M. P.; Praki, K.; Ryan, S. M.; Skullerud, J.-I.

    2016-12-01

    The FASTSUM collaboration has been carrying out lattice simulations of QCD for temperatures ranging from one third to twice the crossover temperature, investigating the transition region, as well as the properties of the Quark Gluon Plasma. In this contribution we concentrate on quarkonium correlators and spectral functions. We work in a fixed scale scheme and use anisotropic lattices which help achieving the desirable fine resolution in the temporal direction, thus facilitating the (ill posed) integral transform from imaginary time to frequency space. We contrast and compare results for the correlators obtained with different methods, and different temporal spacings. We observe robust features of the results, confirming the sequential dissociation scenario, but also quantitative differences indicating that the methods' systematic errors are not yet under full control. We briefly outline future steps towards accurate results for the spectral functions and their associated statistical and systematic errors.

  11. Spectral partitioning of random regular blockmodels

    CERN Document Server

    Barucca, Paolo

    2016-01-01

    Graph partitioning problems emerge in a wide variety of complex systems, ranging from biology to finance, but can be rigorously analyzed and solved only for a few graph ensembles. Here, an ensemble of random graphs with regular block structure is introduced, for which analytical results can be obtained. In particular, the spectral density of such random regular blockmodels is computed exactly for a modular, bipartite and core-periphery structure. McKay's law for random regular graphs is found analytically to apply also for regular modular and bipartite structures when blocks are homogeneous. In core-periphery structures, where blocks are intrinsically heterogeneous, a new law is found to apply for the spectral density. Exact solution to the inference problem is provided for the models discussed. All analytical results show perfect agreement with numerical experiments. Final discussion summarizes results and outlines the relevance of the results for the solution of graph partitioning problems in other graph en...

  12. Infinite matter properties and zero-range limit of nonrelativistic finite-range interactions

    CERN Document Server

    Davesne, D; Pastore, A; Navarro, J

    2016-01-01

    We discuss some infinite matter properties of two finite-range interactions widely used for nuclear structure calculations, namely Gogny and M3Y interactions. We show that some useful informations can be deduced for the central, tensor and spin-orbit terms from the spin-isospin channels and the partial wave decomposition of the symmetric nuclear matter equation of state. We show in particular that the central part of the Gogny interaction should benefit from the introduction of a third Gaussian and the tensor parameters of both interactions can be deduced from special combinations of partial waves. We also discuss the fact that the spin-orbit of the M3Y interaction is not compatible with local gauge invariance. Finally, we show that the zero-range limit of both families of interactions coincides with the specific form of the zero-range N3LO Skyrme interaction and we emphasize from this analogy the benefits of N3LO.

  13. Infinite matter properties and zero-range limit of non-relativistic finite-range interactions

    Science.gov (United States)

    Davesne, D.; Becker, P.; Pastore, A.; Navarro, J.

    2016-12-01

    We discuss some infinite matter properties of two finite-range interactions widely used for nuclear structure calculations, namely Gogny and M3Y interactions. We show that some useful informations can be deduced for the central, tensor and spin-orbit terms from the spin-isospin channels and the partial wave decomposition of the symmetric nuclear matter equation of state. We show in particular that the central part of the Gogny interaction should benefit from the introduction of a third Gaussian and the tensor parameters of both interactions can be deduced from special combinations of partial waves. We also discuss the fact that the spin-orbit of the M3Y interaction is not compatible with local gauge invariance. Finally, we show that the zero-range limit of both families of interactions coincides with the specific form of the zero-range Skyrme interaction extended to higher momentum orders and we emphasize from this analogy its benefits.

  14. Infinite matter properties and zero-range limit of non-relativistic finite-range interactions

    Energy Technology Data Exchange (ETDEWEB)

    Davesne, D. [Université de Lyon, Université Lyon 1, CNRS/IN2P3, Institut de Physique Nucléaire de Lyon, UMR 5822, F-69622 Villeurbanne cedex (France); Becker, P., E-mail: pbecker@ipnl.in2p3.fr [Université de Lyon, Université Lyon 1, CNRS/IN2P3, Institut de Physique Nucléaire de Lyon, UMR 5822, F-69622 Villeurbanne cedex (France); Pastore, A. [Department of Physics, University of York, Heslington, York, Y010 5DD (United Kingdom); Navarro, J. [IFIC (CSIC-Universidad de Valencia), Apartado Postal 22085, E-46.071-Valencia (Spain)

    2016-12-15

    We discuss some infinite matter properties of two finite-range interactions widely used for nuclear structure calculations, namely Gogny and M3Y interactions. We show that some useful informations can be deduced for the central, tensor and spin–orbit terms from the spin–isospin channels and the partial wave decomposition of the symmetric nuclear matter equation of state. We show in particular that the central part of the Gogny interaction should benefit from the introduction of a third Gaussian and the tensor parameters of both interactions can be deduced from special combinations of partial waves. We also discuss the fact that the spin–orbit of the M3Y interaction is not compatible with local gauge invariance. Finally, we show that the zero-range limit of both families of interactions coincides with the specific form of the zero-range Skyrme interaction extended to higher momentum orders and we emphasize from this analogy its benefits.

  15. Dependence of Wave Height Distribution on Spectral Width and Wave Steepness

    Institute of Scientific and Technical Information of China (English)

    文凡; 吴自库; 吕红民

    2004-01-01

    In this paper experimental wind wave data are analyzed. It is found that differences in spectral width will give rise to differences in wave height distribution. The effect of spectral width on the distribution is mainly in the high wave range.The effect of wave steepness is in low, medium and high wave ranges. In the high wave range the effect of spectral width is comparable to that of wave steepness. Differences in spectral width in the observations may give rise to discrepancies in the result when wave steepness is the only parameter in the distribution.

  16. [Morphological changes in gastric wall of mongolian gerbils following the 12-day orbital flight aboard Foton-M3].

    Science.gov (United States)

    Atiashkin, D A; Bykov, É G

    2012-01-01

    Gastric wall of Meriones unguiculatus is distinguished by species-specific properties arising from the peculiar proportion of interstitium, muscle and epithelial tissues. Exposure to the factors of the 12-d Foton-M3 flight led to microfocal lesions of the mucous coat, dystrophic developments in the acid glands, dissociation of the mucous barrier function and deterioration of its biosynthetic function. Modifications of the tinctorial properties of the interstitium reticulum in every stomach layer progressed concurrently with reductions in prismatic epithelium height, as well as in mucous and muscular layer thickness. It is assumed that existence in the low gravity aboard the Biosat stimulated involutory processes in the gastric wall. Animals of the ground synchronous control conducted in the flight equipment mockup (Kontur-L) exhibited though similar yet less pronounced changes.

  17. Elements in the canine distemper virus M 3' UTR contribute to control of replication efficiency and virulence.

    Directory of Open Access Journals (Sweden)

    Danielle E Anderson

    Full Text Available Canine distemper virus (CDV is a negative-sense, single-stranded RNA virus within the genus Morbillivirus and the family Paramyxoviridae. The Morbillivirus genome is composed of six transcriptional units that are separated by untranslated regions (UTRs, which are relatively uniform in length, with the exception of the UTR between the matrix (M and fusion (F genes. This UTR is at least three times longer and in the case of CDV also highly variable. Exchange of the M-F region between different CDV strains did not affect virulence or disease phenotype, demonstrating that this region is functionally interchangeable. Viruses carrying the deletions in the M 3' UTR replicated more efficiently, which correlated with a reduction of virulence, suggesting that overall length as well as specific sequence motifs distributed throughout the region contribute to virulence.

  18. Conversión de diagramas de procesos en diagramas de casos de usos usando AToM3

    Directory of Open Access Journals (Sweden)

    CARLOS M. ZAPATA J.

    2005-01-01

    Full Text Available Toda pieza de software se origina en el modelo verbal, con el cual se pueden definir los diferentes modelos conceptuales que acerquen el problema a una solución. Las herramientas convencionales para la construcción de los modelos conceptuales no toman en consideración las diferentes reglas de consistencia que se pueden presentar entre los diferentes modelos. En este artículo se emplea el AToM3 como herramienta para la definición de los meta-modelos del diagrama de procesos y el diagrama de casos de uso, con el fin de reexpresar el primero para obtener algunos elementos básicos del segundo.

  19. Photometric and spectroscopic observations of the F3+M3 eclipsing binary T-Lyr0-08070

    CERN Document Server

    Cakirli, O; Sipahi, E

    2012-01-01

    The multi-color photometric and spectroscopic observations of the newly discovered eclipsing binary T-Lyr0-08070 were obtained. The resultant light and radial velocities were analysed and the absolute parameters of the components were determined. The system is composed of an F3 and an M3 main-sequence stars. Masses and radii were estimated to be 1.37$\\pm$0.23 M$_{\\odot}$ and 1.60$\\pm$0.09 R$_{\\odot}$ for the primary and 0.32$\\pm$0.04 M$_{\\odot}$ and 0.86$\\pm$0.06R$_{\\odot}$ for the secondary star. The less massive secondary component has a radius at least two times larger with respect to its mass. Using the BVJHK magnitudes of the system we estimated an interstellar reddening of 0.22 mag and a distance to the system as 479$\\pm$36 pc.

  20. Moment Tensors and their Uncertainties for M3 Earthquakes in the Geysers, California, from Waveform Modeling and First Motions

    Science.gov (United States)

    Guilhem, A.; Dreger, D. S.; Hutchings, L. J.; Johnson, L.

    2012-12-01

    We investigate moment tensor solutions and their uncertainties for magnitude (M) ~3 earthquakes located in the northwest Geysers geothermal field, California. We are exploiting an unusual opportunity where data for M~3 events have been recorded by three different networks and have moment tensor solutions calculated by three different methods. We solve for both deviatoric and full moment tensor solutions. The data sets include local short-period instruments (4.5 Hz) of the 30 stations of the Lawrence Berkeley National Laboratory (LBNL), with which we obtain waveform inversion solutions at relatively high frequencies (i.e., up to 2.5 Hz), and regionally distributed broadband stations operated by the Berkeley Seismological Laboratory (BSL), with which are used to provide waveform inversion solutions with data filtered at longer periods (i.e., > 10 sec). We also utilize the LBNL data to obtain moment tensor solutions by fitting the P-wave first motions. The USGS, LBNL, and BSL obtain different event locations, utilize different velocity models, and analyze different frequency bands and wave types (i.e., body waves for LBNL method and primarily surface waves for the BSL analysis). Preliminary results indicate that the BSL and LBNL waveform modeling analyses give similar results in terms of nodal plane characteristics, moment magnitude, and moment tensor decomposition. Analysis of the P-wave first motions recorded by LBNL stations can illuminate complexities in the source processes when compared to waveform moment tensor solutions. We discuss uncertainties in the source inversions that use broadband and/or short-period waveform modeling, and in the source inversions from first motions only. We also combine the different datasets and compare their individual importance as they can help illustrate the complex source processes happening in the Geysers. This study introduces the possibility to interpret the seismic sources as complex processes in which both shear and tensile