WorldWideScience

Sample records for m11 portable decontamination

  1. Testing of a portable ultrahigh pressure water decontamination system (UHPWDS)

    Energy Technology Data Exchange (ETDEWEB)

    Lovell, A.; Dahlby, J.

    1996-02-01

    This report describes the tests done with a portable ultrahigh pressure water decontamination system (UHPWDS) on highly radioactively contaminated surfaces. A small unit was purchased, modified, and used for in-situ decontamination to change the waste level of the contaminated box from transuranic (TRU) waste to low- level waste (LLW). Low-level waste is less costly by as much as a factor of five or more if compared with TRU waste when handling, storage, and disposal are considered. The portable unit we tested is commercially available and requires minimal utilities for operation. We describe the UHPWDS unit itself, a procedure for its use, the results of the testing we did, and conclusions including positive and negative aspects of the UHPWDS.

  2. Portable Chemical Sterilizer for Microbial Decontamination of Surgical Instruments, Fruits and Vegetables, and Field Feeding Equipment

    National Research Council Canada - National Science Library

    Doona, C. J; Feeherry, F. E; Kustin, K; Curtin, M. A; Baer, D. G

    2006-01-01

    The Portable Chemical Sterilizer (PCS) is a revolutionary biomedical sterilization technology that provides the capability for portable, power-free, point-of-use sterilization to meet the Army's Far-Forward Surgical Teams (FSTs...

  3. Development of a Portable Sensitive Equipment Decontamination System. Volume 2: Activated Carbon Fiber Wipe

    Science.gov (United States)

    2010-05-01

    Wipe) and the measurements taken to determine its performance. 15. SUBJECT TERMS Wipes CARC ACAMS Decontaminant GD DAAMS Antibacterial HFE VX...30 4.4.8.3 Extraction Procedure for Wiper Layers 30 4.4.9 Validation Baseline Wiping Efficacy Tests 31 4.4.9.1 Effect of Multiple Wipe Cycles 32...and Wipe Testing 38 4.4.13 Contaminant Off-Gassing from Activated Carbon Fabrics 40 4.4.14 Off-Gassing of CEES 41 4.4.15 Off-Gassing of Bonide Fruit

  4. The Portable Chemical Sterilizer (PCS), D-FENS, and D-FEND ALL: novel chlorine dioxide decontamination technologies for the military.

    Science.gov (United States)

    Doona, Christopher J; Feeherry, Florence E; Setlow, Peter; Malkin, Alexander J; Leighton, Terrence J

    2014-06-29

    There is a stated Army need for a field-portable, non-steam sterilizer technology that can be used by Forward Surgical Teams, Dental Companies, Veterinary Service Support Detachments, Combat Support Hospitals, and Area Medical Laboratories to sterilize surgical instruments and to sterilize pathological specimens prior to disposal in operating rooms, emergency treatment areas, and intensive care units. The following ensemble of novel, 'clean and green' chlorine dioxide technologies are versatile and flexible to adapt to meet a number of critical military needs for decontamination(6,15). Specifically, the Portable Chemical Sterilizer (PCS) was invented to meet urgent battlefield needs and close critical capability gaps for energy-independence, lightweight portability, rapid mobility, and rugged durability in high intensity forward deployments(3). As a revolutionary technological breakthrough in surgical sterilization technology, the PCS is a Modern Field Autoclave that relies on on-site, point-of-use, at-will generation of chlorine dioxide instead of steam. Two (2) PCS units sterilize 4 surgical trays in 1 hr, which is the equivalent throughput of one large steam autoclave (nicknamed "Bertha" in deployments because of its cumbersome size, bulky dimensions, and weight). However, the PCS operates using 100% less electricity (0 vs. 9 kW) and 98% less water (10 vs. 640 oz.), significantly reduces weight by 95% (20 vs. 450 lbs, a 4-man lift) and cube by 96% (2.1 vs. 60.2 ft(3)), and virtually eliminates the difficult challenges in forward deployments of repairs and maintaining reliable operation, lifting and transporting, and electrical power required for steam autoclaves.

  5. Environmental decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Cristy, G.A.; Jernigan, H.C. (eds.)

    1981-02-01

    The record of the proceedings of the workshop on environmental decontamination contains twenty-seven presentations. Emphasis is placed upon soil and surface decontamination, the decommissioning of nuclear facilities, and assessments of instrumentation and equipment used in decontamination. (DLS)

  6. Decontamination Data - Blister Agents

    Data.gov (United States)

    U.S. Environmental Protection Agency — Decontamination efficacy data for blister agents on various building materials using various decontamination solutions. This dataset is associated with the following...

  7. Amalgams of Rank 2 and Characteristic 3 Involving M11

    Institute of Scientific and Technical Information of China (English)

    黄建华; 李慧陵

    1994-01-01

    In this paper we investigate the amalgams (M11,X) of rank 2 and characteristic 3,where X is a group of Lie type of rank 1 or permutation group of low rank,and give a characterization of the 3 local subgroups of the finite sporadic groups Co3 of Ly and Suz.

  8. Gross decontamination experiment report

    Energy Technology Data Exchange (ETDEWEB)

    Mason, R.; Kinney, K.; Dettorre, J.; Gilbert, V.

    1983-07-01

    A Gross Decontamination Experiment was conducted on various levels and surfaces of the TMI - Unit 2 reactor building in March 1982. The polar crane, D-rings, missile shields, refueling canals, refueling bridges, equipment, and elevations 305' and 347'-6'' were flushed with low pressure water. Additionally, floor surfaces on elevation 305' and floor surfaces and major pieces of equipment on elevation 347'-6'' were sprayed with high pressure water. Selective surfaces were decontaminated with a mechanical scrubber and chemicals. Strippable coating was tested and evaluated on equipment and floor surfaces. The effectiveness, efficiency, and safety of several decontamination techniques were established for the large, complex decontamination effort. Various decontamination equipment was evaluated and its effectiveness was documented. Decontamination training and procedures were documented and evaluated, as were the support system and organization for the experiment.

  9. Courseware Portability.

    Science.gov (United States)

    Fletcher, J. D.

    Portability enables interactive courseware (ICW) and associated application programs to operate on computer-based systems other than the ones on which they are developed. Courseware portability will increase sharing of ICW across a range of instructional settings within military services and across internationally allied military services. The…

  10. PWR decontamination feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Silliman, P.L.

    1978-12-18

    The decontamination work which has been accomplished is reviewed and it is concluded that it is worthwhile to investigate further four methods for decontamination for future demonstration. These are: dilute chemical; single stage strong chemical; redox processes; and redox/chemical in combination. Laboratory work is recommended to define the agents and processes for demonstration and to determine the effect of the solvents on PWR materials. The feasibility of Indian Point 1 for decontamination demonstrations is discussed, and it is shown that the system components of Indian Point 1 are well suited for use in demonstrations.

  11. Long lasting decontamination foam

    Science.gov (United States)

    Demmer, Ricky L.; Peterman, Dean R.; Tripp, Julia L.; Cooper, David C.; Wright, Karen E.

    2010-12-07

    Compositions and methods for decontaminating surfaces are disclosed. More specifically, compositions and methods for decontamination using a composition capable of generating a long lasting foam are disclosed. Compositions may include a surfactant and gelatin and have a pH of less than about 6. Such compositions may further include affinity-shifting chemicals. Methods may include decontaminating a contaminated surface with a composition or a foam that may include a surfactant and gelatin and have a pH of less than about 6.

  12. Food decontamination using nanomaterials

    Science.gov (United States)

    The research indicates that nanomaterials including nanoemulsions are promising decontamination media for the reduction of food contaminating pathogens. The inhibitory effect of nanoparticles for pathogens could be due to deactivate cellular enzymes and DNA; disrupting of membrane permeability; and/...

  13. Facility decontamination technology workshop

    Energy Technology Data Exchange (ETDEWEB)

    None

    1980-10-01

    Purpose of the meeting was to provide a record of experience at nuclear facilities, other than TMI-2, of events and incidents which have required decontamination and dose reduction activities, and to furnish GPU and others involved in the TMI-2 cleanup with the results of that decontamination and dose reduction technology. Separate abstracts were prepared for 24 of the 25 papers; the remaining paper had been previously abstracted. (DLC)

  14. Chemical Decontaminant Testing

    Science.gov (United States)

    2014-10-20

    any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display...Some test methods for efficacy require the use of CWAs and decontaminants. 15. SUBJECT TERMS decontamination; chemical warfare agent; CWA...contaminant in samples from contact samplers , coupons, rinsate, or other samples. MS, GC or LC, FID, FPD, or equivalents. ±15 percent of the mass of

  15. Lessons Learned from Decontamination Experiences

    Energy Technology Data Exchange (ETDEWEB)

    Sorensen, JH

    2000-11-16

    This interim report describes a DOE project currently underway to establish what is known about decontamination of buildings and people and the procedures and protocols used to determine when and how people or buildings are considered ''clean'' following decontamination. To fulfill this objective, the study systematically examined reported decontamination experiences to determine what procedures and protocols are currently employed for decontamination, the timeframe involved to initiate and complete the decontamination process, how the contaminants were identified, the problems encountered during the decontamination process, how response efforts of agencies were coordinated, and the perceived social psychological effects on people who were decontaminated or who participated in the decontamination process. Findings and recommendations from the study are intended to aid decision-making and to improve the basis for determining appropriate decontamination protocols for recovery planners and policy makers for responding to chemical and biological events.

  16. Aquatic Toxicity of the Decontamination Agent: Multipurpose (DAM) decontamination Solution

    Science.gov (United States)

    1994-05-01

    DECONTAMINATION SOLUTION ELETI M.V. Holey •I• E LF- , C.W. Kurnas J •i W.T. Muse B RESEARCH AND TECHNOLOGY DIRECTORATE May 1994 Approved for public release...FUNDING NUMBERS Aquatic Toxicity of the Decontaminating S.O.-2FK4 Agent: Multipurpose (DAM) Decontamination Solution 6. AUTHOR(S) Haley, M.V.; Kurnas

  17. Electrokinetic decontamination of concrete

    Energy Technology Data Exchange (ETDEWEB)

    Lomasney, H. [ISOTRON Corp., New Orleans, LA (United States)

    1995-10-01

    The U.S. Department of Energy has assigned a priority to the advancement of technology for decontaminating concrete surfaces which have become contaminated with radionuclides, heavy metals, and toxic organics. This agency is responsible for decontamination and decommissioning of thousands of buildings. Electrokinetic extraction is one of the several innovative technologies which emerged in response to this initiative. This technique utilizes an electropotential gradient and the subsequent electrical transport mechanism to cause the controlled movement of ionics species, whereby the contaminants exit the recesses deep within the concrete. This report discusses the technology and use at the Oak Ridge k-25 plant.

  18. Decontamination: back to basics.

    Science.gov (United States)

    Meredith, Susan J; Sjorgen, Geoff

    2008-07-01

    My invitation from this Journal's Editor, Felicia Cox, to provide a paper for this themed issue, included the sentence 'I was wondering if you or a colleague would like to contribute a back to basics article on the relevant standards and guidelines for decontamination, including what is compliance?'. The reason it is so interesting to me is that the term 'back to basics' implies reverting to a simpler time in life - when by just sticking to the rules, life became easier. However, with decontamination this is not actually true.

  19. [Advances in peroxide-based decontaminating technologies].

    Science.gov (United States)

    Xi, Hai-ling; Zhao, San-ping; Zhou, Wen

    2013-05-01

    With the boosting demand for eco-friendly decontaminants, great achievements in peroxide-based decontaminating technologies have been made in recent years. These technologies have been applied in countering chemical/biological terrorist attacks, dealing with chemical/biological disasters and destructing environmental pollutants. Recent research advances in alpha-nucleophilic/oxidative reaction mechanisms of peroxide-based decontamination against chemical warfare agents were reviewed, and some classical peroxide-based decontaminants such as aqueous decontaminating solution, decontaminating foam, decontaminating emulsions, decontaminating gels, decontaminating vapors, and some newly developed decontaminating media (e.g., peroxide-based self-decontaminating materials and heterogeneous nano-catalytic decontamination systems) were introduced. However, currently available peroxide-based decontaminants still have some deficiencies. For example, their decontamination efficiencies are not as high as those of chlorine-containing decontaminants, and some peroxide-based decontaminants show relatively poor effect against certain agents. More study on the mechanisms of peroxide-based decontaminants and the interfacial interactions in heterogeneous decontamination media is suggested. New catalysts, multifunctional surfactants, self-decontaminating materials and corrosion preventing technologies should be developed before peroxide-based decontaminants really become true "green" decontaminants.

  20. Decontamination and protection

    Energy Technology Data Exchange (ETDEWEB)

    Maloney, J.C.; Dhein, E.H.; Morgenthau, M.

    1954-01-01

    Test panels, four ft square, of 14 building materials were mounted on the weather surfaces of two remotely controlled liberty ships and on a stationary barge. One of the ships was protected by a washdown system. All surfaces were contaminated significantly with tenacious fallout. Vertical surfaces facing upwind became equally or more highly contaminated than horizontal or pitched surfaces, probably due to wind currents impacting the tenacious contaminant onto surfaces normal to it. A sequence of hosing and vigorous scrubbing operations resulted in contamination reductions of 40 to 70%, but with reductions on most surfaces being less than 50%. The most effective decontamination method was scrubbing. Under the conditions of this test, painting and joint sealing had little effect while the washdown countermeasure reduced the initial contamination over 90%. It is concluded that contamination from fallout encountered in these tests presents a serious decontamination problem on buildings and paved areas and further development of effective countermeasures is necessary.

  1. Development of laser decontamination technique

    Energy Technology Data Exchange (ETDEWEB)

    Ogawa, Ryuichiro; Fukui, Yasutaka; Tanimoto, Kenichi [Japan Nuclear Cycle Development Inst., Oarai, Ibaraki (Japan). Oarai Engineering Center

    2002-06-01

    For decommissioning of nuclear fuel facilities, a laser decontamination technique has been developed. The technique was expected to decontaminate high-level radioactive waste to back ground levels, keep the amount of secondary waste low, and be operated by remote control. In the development, a decontamination experiment was executed. Type and operation mode of the laser oscillator, Type and flow rate of the assist gas, repetition rate of the laser pulse, moving velocity of the laser nozzle and irradiation energy were parameters in the experiment. Hot radioactive waste could be decontaminated to background levels uniformly with optimized parameters, which were determined by comparative evaluation. (author)

  2. Development of a Portable Binary Chlorine Dioxide Generator for Decontamination

    Science.gov (United States)

    2010-03-01

    solutions, but the yields do not vary linearly with increasing chlorite concentrations in the > 50 mM range as predicted by the PFR model, and indeed...the PFR model. We considered two dominant factors. First, kinetic saturation can occur if the chlorite concentration is so high that bromine...Cmax) due to physical flow in large spaces and perhaps other side reactions not yet identified. Thus the poor overall fit of the basic PFR model is

  3. Potential biodefense model applications for portable chlorine dioxide gas production.

    Science.gov (United States)

    Stubblefield, Jeannie M; Newsome, Anthony L

    2015-01-01

    Development of decontamination methods and strategies to address potential infectious disease outbreaks and bioterrorism events are pertinent to this nation's biodefense strategies and general biosecurity. Chlorine dioxide (ClO2) gas has a history of use as a decontamination agent in response to an act of bioterrorism. However, the more widespread use of ClO2 gas to meet current and unforeseen decontamination needs has been hampered because the gas is too unstable for shipment and must be prepared at the application site. Newer technology allows for easy, onsite gas generation without the need for dedicated equipment, electricity, water, or personnel with advanced training. In a laboratory model system, 2 unique applications (personal protective equipment [PPE] and animal skin) were investigated in the context of potential development of decontamination protocols. Such protocols could serve to reduce human exposure to bacteria in a decontamination response effort. Chlorine dioxide gas was capable of reducing (2-7 logs of vegetative and spore-forming bacteria), and in some instances eliminating, culturable bacteria from difficult to clean areas on PPE facepieces. The gas was effective in eliminating naturally occurring bacteria on animal skin and also on skin inoculated with Bacillus spores. The culturable bacteria, including Bacillus spores, were eliminated in a time- and dose-dependent manner. Results of these studies suggested portable, easily used ClO2 gas generation systems have excellent potential for protocol development to contribute to biodefense strategies and decontamination responses to infectious disease outbreaks or other biothreat events.

  4. Skin decontamination: principles and perspectives.

    Science.gov (United States)

    Chan, Heidi P; Zhai, Hongbo; Hui, Xiaoying; Maibach, Howard I

    2013-11-01

    Skin decontamination is the primary intervention needed in chemical, biological and radiological exposures, involving immediate removal of the contaminant from the skin performed in the most efficient way. The most readily available decontamination system on a practical basis is washing with soap and water or water only. Timely use of flushing with copious amounts of water may physically remove the contaminant. However, this traditional method may not be completely effective, and contaminants left on the skin after traditional washing procedures can have toxic consequences. This article focuses on the principles and practices of skin decontamination.

  5. Decontamination & decommissioning focus area

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-01

    In January 1994, the US Department of Energy Office of Environmental Management (DOE EM) formally introduced its new approach to managing DOE`s environmental research and technology development activities. The goal of the new approach is to conduct research and development in critical areas of interest to DOE, utilizing the best talent in the Department and in the national science community. To facilitate this solutions-oriented approach, the Office of Science and Technology (EM-50, formerly the Office of Technology Development) formed five Focus AReas to stimulate the required basic research, development, and demonstration efforts to seek new, innovative cleanup methods. In February 1995, EM-50 selected the DOE Morgantown Energy Technology Center (METC) to lead implementation of one of these Focus Areas: the Decontamination and Decommissioning (D & D) Focus Area.

  6. Large-bore pipe decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Ebadian, M.A.

    1998-01-01

    The decontamination and decommissioning (D and D) of 1200 buildings within the US Department of Energy-Office of Environmental Management (DOE-EM) Complex will require the disposition of miles of pipe. The disposition of large-bore pipe, in particular, presents difficulties in the area of decontamination and characterization. The pipe is potentially contaminated internally as well as externally. This situation requires a system capable of decontaminating and characterizing both the inside and outside of the pipe. Current decontamination and characterization systems are not designed for application to this geometry, making the direct disposal of piping systems necessary in many cases. The pipe often creates voids in the disposal cell, which requires the pipe to be cut in half or filled with a grout material. These methods are labor intensive and costly to perform on large volumes of pipe. Direct disposal does not take advantage of recycling, which could provide monetary dividends. To facilitate the decontamination and characterization of large-bore piping and thereby reduce the volume of piping required for disposal, a detailed analysis will be conducted to document the pipe remediation problem set; determine potential technologies to solve this remediation problem set; design and laboratory test potential decontamination and characterization technologies; fabricate a prototype system; provide a cost-benefit analysis of the proposed system; and transfer the technology to industry. This report summarizes the activities performed during fiscal year 1997 and describes the planned activities for fiscal year 1998. Accomplishments for FY97 include the development of the applicable and relevant and appropriate regulations, the screening of decontamination and characterization technologies, and the selection and initial design of the decontamination system.

  7. DECONTAMINATION TECHNOLOGIES FOR FACILITY REUSE

    Energy Technology Data Exchange (ETDEWEB)

    Bossart, Steven J.; Blair, Danielle M.

    2003-02-27

    As nuclear research and production facilities across the U.S. Department of Energy (DOE) nuclear weapons complex are slated for deactivation and decommissioning (D&D), there is a need to decontaminate some facilities for reuse for another mission or continued use for the same mission. Improved technologies available in the commercial sector and tested by the DOE can help solve the DOE's decontamination problems. Decontamination technologies include mechanical methods, such as shaving, scabbling, and blasting; application of chemicals; biological methods; and electrochemical techniques. Materials to be decontaminated are primarily concrete or metal. Concrete materials include walls, floors, ceilings, bio-shields, and fuel pools. Metallic materials include structural steel, valves, pipes, gloveboxes, reactors, and other equipment. Porous materials such as concrete can be contaminated throughout their structure, although contamination in concrete normally resides in the top quarter-inch below the surface. Metals are normally only contaminated on the surface. Contamination includes a variety of alpha, beta, and gamma-emitting radionuclides and can sometimes include heavy metals and organic contamination regulated by the Resource Conservation and Recovery Act (RCRA). This paper describes several advanced mechanical, chemical, and other methods to decontaminate structures, equipment, and materials.

  8. Selective decontamination and antibiotic resistance in ICUs

    NARCIS (Netherlands)

    Plantinga, Nienke L.; Bonten, Marc J. M.|info:eu-repo/dai/nl/123144337

    2015-01-01

    Selective digestive decontamination (SDD) and selective oropharyngeal decontamination (SOD) have been associated with reduced mortality and lower ICU-acquired bacteremia and ventilator-associated pneumonia rates in areas with low levels of antibiotic resistance. However, the effect of selective

  9. Public experiences of mass casualty decontamination.

    Science.gov (United States)

    Carter, Holly; Drury, John; Rubin, G James; Williams, Richard; Amlôt, Richard

    2012-09-01

    In this article, we analyze feedback from simulated casualties who took part in field exercises involving mass decontamination, to gain an understanding of how responder communication can affect people's experiences of and compliance with decontamination. We analyzed questionnaire data gathered from 402 volunteers using the framework approach, to provide an insight into the public's experiences of decontamination and how these experiences are shaped by the actions of emergency responders. Factors that affected casualties' experiences of the decontamination process included the need for greater practical information and better communication from responders, and the need for privacy. Results support previous findings from small-scale incidents that involved decontamination in showing that participants wanted better communication from responders during the process of decontamination, including more practical information, and that the failure of responders to communicate effectively with members of the public led to anxiety about the decontamination process. The similarity between the findings from the exercises described in this article and previous research into real incidents involving decontamination suggests that field exercises provide a useful way to examine the effect of responder communication strategies on the public's experiences of decontamination. Future exercises should examine in more detail the effect of various communication strategies on the public's experiences of decontamination. This will facilitate the development of evidence-based communication strategies intended to reduce anxiety about decontamination and increase compliance among members of the public during real-life incidents that involve mass decontamination.

  10. Decontamination in a Russian settlement

    DEFF Research Database (Denmark)

    Fogh, C.L.; Andersson, Kasper Grann; Barkovsky, A.N.

    1999-01-01

    Decontamination was carried out in an area with three houses in Novo Bobovichi, Bryansk region, Russia, in the autumn of 1995. It was demonstrated that significant reductions in the dose rate both indoor (DRF = 0.34) and outdoor (DRF = 0.20) can be achieved when a controlled cleaning is undertaken...

  11. Detection and decontamination of residual energetics from ordnance and explosives scrap.

    Science.gov (United States)

    Jung, Carina M; Newcombe, David A; Crawford, Don L; Crawford, Ronald L

    2004-02-01

    Extensive manufacturing of explosives in the last century has resulted in widespread contamination of soils and waters. Decommissioning and cleanup of these materials has also led to concerns about the explosive hazards associated with residual energetics still present on the surfaces of ordnance and explosives scrap. Typically, open burning or detonation is used to decontaminate ordinance and explosive scrap. Here the use of an anaerobic microbiological system applied as a bioslurry to decontaminate energetics from the surfaces of metal scrap is described. Decontamination of model metal scrap artificially contaminated with 2,4,6-trinitrotoluene and of decommissioned mortar rounds still containing explosives residue was examined. A portable ion mobility spectrometer was employed for the detection of residual explosives residues on the surfaces of the scrap. The mixed microbial populations of the bioslurries effectively decontaminated both the scrap and the mortar rounds. Use of the ion mobility spectrometer was an extremely sensitive field screening method for assessing decontamination and is a method by which minimally trained personnel can declare scrap clean with a high level of certainty.

  12. Review of the MDF-LSA 100 Spray Decontamination System

    Science.gov (United States)

    2011-12-01

    UNCLASSIFIED Review of the MDF -LSA 100 Spray Decontamination System Rodi Sferopoulos Human Protection and Performance Division...and performance of the Modec Decontamination Foam ( MDF )-LSA 100 Spray Decontamination System as well as information regarding the decontamination...RELEASE UNCLASSIFIED UNCLASSIFIED UNCLASSIFIED Review of the MDF -LSA 100 Spray Decontamination System Executive Summary DSTO were

  13. Software Engineering for Portability.

    Science.gov (United States)

    Stanchev, Ivan

    1990-01-01

    Discussion of the portability of educational software focuses on the software design and development process. Topics discussed include levels of portability; the user-computer dialog; software engineering principles; design techniques for student performance records; techniques of courseware programing; and suggestions for further research and…

  14. Portable raman explosives detection

    Energy Technology Data Exchange (ETDEWEB)

    Moore, David Steven [Los Alamos National Laboratory; Scharff, Robert J [Los Alamos National Laboratory

    2008-01-01

    Recent advances in portable Raman instruments have dramatically increased their application to emergency response and forensics, as well as homeland defense. This paper reviews the relevant attributes and disadvantages of portable Raman spectroscopy, both essentially and instrumentally, to the task of explosives detection in the field.

  15. Decontamination in a Russian settlement

    Energy Technology Data Exchange (ETDEWEB)

    Roed, J.; Lange, C.; Andersson, K.G. [and others

    1996-03-01

    Decontamination was carried out in and around three houses in Novo Bobovichi, Russia, in the autumn of 1995. It was demonstrated that significant reductions in the dose rate both indoor (DRF = 0.34) and outdoor (DRF = 0.20) can be achieved when a careful cleaning is undertaken. This report describes the decontamination work carried out and the results obtained. The roofs of the houses were swept and cleaned by special roof cleaning equipment. The soil around the houses was removed by hand while carefully monitoring the ground for residual contamination. By monitoring the decline in the dose rate during the different stages of the work the dose reducing effect of each action has been estimated. This report also describes a test of a triple digging method that reduces the dose rate without generating waste. In the appendices of the report the measurement data are available for further analysis. (au) 16 tabs., 15 ills.

  16. Decontamination of Drinking Water Infrastructure ...

    Science.gov (United States)

    Technical Brief This study examines the effectiveness of decontaminating corroded iron and cement-mortar coupons that have been contaminated with spores of Bacillus atrophaeus subsp. globigii (B. globigii), which is often used as a surrogate for pathogenic B. anthracis (anthrax) in disinfection studies. Bacillus spores are persistent on common drinking water material surfaces like corroded iron, requiring physical or chemical methods to decontaminate the infrastructure. In the United States, free chlorine and monochloramine are the primary chemical disinfectants used by the drinking water industry to inactivate microorganisms. Flushing is also a common, easily implemented practice in drinking water distribution systems, although large volumes of contaminated water needing treatment could be generated. Identifying readily available alternative disinfectant formulations for infrastructure decontamination could give water utilities options for responding to specific types of contamination events. In addition to presenting data on flushing alone, which demonstrated the persistence of spores on water infrastructure in the absence of high levels of disinfectants, data on acidified nitrite, chlorine dioxide, free chlorine, monochloramine, ozone, peracetic acid, and followed by flushing are provided.

  17. Pickering emulsions for skin decontamination.

    Science.gov (United States)

    Salerno, Alicia; Bolzinger, Marie-Alexandrine; Rolland, Pauline; Chevalier, Yves; Josse, Denis; Briançon, Stéphanie

    2016-08-01

    This study aimed at developing innovative systems for skin decontamination. Pickering emulsions, i.e. solid-stabilized emulsions, containing silica (S-PE) or Fuller's earth (FE-PE) were formulated. Their efficiency for skin decontamination was evaluated, in vitro, 45min after an exposure to VX, one of the most highly toxic chemical warfare agents. Pickering emulsions were compared to FE (FE-W) and silica (S-W) aqueous suspensions. PE containing an oil with a similar hydrophobicity to VX should promote its extraction. All the formulations reduced significantly the amount of VX quantified on and into the skin compared to the control. Wiping the skin surface with a pad already allowed removing more than half of VX. FE-W was the less efficient (85% of VX removed). The other formulations (FE-PE, S-PE and S-W) resulted in more than 90% of the quantity of VX removed. The charge of particles was the most influential factor. The low pH of formulations containing silica favored electrostatic interactions of VX with particles explaining the better elimination from the skin surface. Formulations containing FE had basic pH, and weak interactions with VX did not improve the skin decontamination. However, these low interactions between VX and FE promote the transfer of VX into the oil droplets in the FE-PE.

  18. Vibratory finishing as a decontamination process

    Energy Technology Data Exchange (ETDEWEB)

    McCoy, M.W.; Arrowsmith, H.W.; Allen, R.P.

    1980-10-01

    The major objective of this research is to develop vibratory finishing into a large-scale decontamination technique that can economicaly remove transuranic and other surface contamination from large volumes of waste produced by the operation and decommissioning of retired nuclear facilities. The successful development and widespread application of this decontamination technique would substantially reduce the volume of waste requiring expensive geologic disposal. Other benefits include exposure reduction for decontamination personnel and reduced risk of environmental contamination. Laboratory-scale studies showed that vibratory finishing can rapidly reduce the contamination level of transuranic-contaminated stainless steel and Plexiglas to well below the 10-nCi/g limit. The capability of vibratory finishing as a decontamination process was demonstrated on a large scale. The first decontamination demonstration was conducted at the Hanford N-Reactor, where a vibratory finisher was installed to reduce personnel exposure during the summer outage. Items decontaminated included fuel spacers, process-tube end caps, process-tube inserts, pump parts, ball-channel inspection tools and miscellaneous hand tools. A second demonstration is currently being conducted in the decontamination facility at the Hanford 231-Z Building. During this demonstration, transuranic-contaminated material from decommissioned plutonium facilities is being decontaminated to <10 nCi/g to minimize the volume of material that will require geologic disposal. Items that are being decontaminated include entire glove boxes, process-hood structural material and panels, process tanks, process-tank shields, pumps, valves and hand tools used during the decommissioning work.

  19. A solar powered handheld plasma source for microbial decontamination applications

    Science.gov (United States)

    Ni, Y.; Lynch, M. J.; Modic, M.; Whalley, R. D.; Walsh, J. L.

    2016-09-01

    A fully portable atmospheric pressure air plasma system is reported to be suitable for the microbial decontamination of both surfaces and liquids. The device operates in quiescent air, and includes an integrated battery which is charged from a solar cell and weighs less than 750 g, making it highly amenable for a wide variety of applications beyond the laboratory. Using particle imaging velocimetry to visualise air flows around the device, the geometric configuration of the plasma generating electrodes was enhanced to induce a gas flow on the order of 0.5 m s-1 directed towards a sample placed downstream, thus improving the transport of plasma generated reactive species to the sample. The microbial decontamination efficiency of the system was assessed using potable water samples inoculated with common waterborne organisms Escherichia coli and Pseudomonas fluorescens. The reduction in the number of microorganisms was found to be in the range of 2-8 log and was strongly dependent on the plasma generation conditions.

  20. Complete genome sequence of Thermosphaera aggregans type strain (M11TLT)

    Energy Technology Data Exchange (ETDEWEB)

    Spring, Stefan [DSMZ - German Collection of Microorganisms and Cell Cultures GmbH, Braunschweig, Germany; Rachel, Dr. Reinhard [Universitat Regensburg, Regensburg, Germany; Lapidus, Alla L. [U.S. Department of Energy, Joint Genome Institute; Davenport, Karen W. [Los Alamos National Laboratory (LANL); Tice, Hope [U.S. Department of Energy, Joint Genome Institute; Copeland, A [U.S. Department of Energy, Joint Genome Institute; Cheng, Jan-Fang [U.S. Department of Energy, Joint Genome Institute; Lucas, Susan [U.S. Department of Energy, Joint Genome Institute; Nolan, Matt [U.S. Department of Energy, Joint Genome Institute; Bruce, David [U.S. Department of Energy, Joint Genome Institute; Goodwin, Lynne A. [Los Alamos National Laboratory (LANL); Pitluck, Sam [U.S. Department of Energy, Joint Genome Institute; Ivanova, N [U.S. Department of Energy, Joint Genome Institute; Mavromatis, K [U.S. Department of Energy, Joint Genome Institute; Ovchinnikova, Galina [U.S. Department of Energy, Joint Genome Institute; Pati, Amrita [U.S. Department of Energy, Joint Genome Institute; Chen, Amy [U.S. Department of Energy, Joint Genome Institute; Palaniappan, Krishna [U.S. Department of Energy, Joint Genome Institute; Land, Miriam L [ORNL; Hauser, Loren John [ORNL; Chang, Yun-Juan [ORNL; Jeffries, Cynthia [Oak Ridge National Laboratory (ORNL); Detter, J. Chris [U.S. Department of Energy, Joint Genome Institute; Tapia, Roxanne [Los Alamos National Laboratory (LANL); Han, Cliff [Los Alamos National Laboratory (LANL); Heimerl, Dr. Thomas [Universitat Regensburg, Regensburg, Germany; Weikl, Fabian [University of Regensburg, Archaeenzentrum, Regensburg, Germany; Brambilla, Evelyne-Marie [DSMZ - German Collection of Microorganisms and Cell Cultures GmbH, Braunschweig, Germany; Goker, Markus [DSMZ - German Collection of Microorganisms and Cell Cultures GmbH, Braunschweig, Germany; Bristow, James [U.S. Department of Energy, Joint Genome Institute; Eisen, Jonathan [U.S. Department of Energy, Joint Genome Institute; Markowitz, Victor [U.S. Department of Energy, Joint Genome Institute; Hugenholtz, Philip [U.S. Department of Energy, Joint Genome Institute; Kyrpides, Nikos C [U.S. Department of Energy, Joint Genome Institute; Klenk, Hans-Peter [DSMZ - German Collection of Microorganisms and Cell Cultures GmbH, Braunschweig, Germany

    2010-01-01

    Thermosphaera aggregans Huber et al. 1998 is the type species of the genus Thermosphaera, which comprises at the time of writing only one species. This species represents archaea with a hyperthermophilic, heterotrophic, strictly anaerobic and fermentative phenotype. The type strain M11TLT was isolated from a water-sediment sample of a hot terrestrial spring (Obsidian Pool, Yellowstone National Park, Wyoming). Here we describe the features of this organism, together with the complete genome sequence and annotation. The 1,316,595 bp long single replicon genome with its 1,410 protein-coding and 47 RNA genes is a part of the Genomic Encyclopedia of Bacteria and Archaea project.

  1. The Detached Eclipsing Binary KV29 and the Age of the Open Cluster M11

    CERN Document Server

    Bavarsad, Ernest A; Shetrone, Matthew D; Orosz, Jerome A

    2016-01-01

    We present an extensive set of photometry and radial velocities for the detached eclipsing binary KV 29 in the intermediate-aged open cluster M11 (NGC 6705). Spectroscopy shows that the system is double-lined and all available evidence (proper motion, photometry, and position on the CMD) indicates it is a member of the cluster. We find the period of the binary to be $4.64276\\pm0.00001$ days. We find masses $3.604^{+0.002}_{-0.011}M_\\odot$ and $1.837^{+0.001}_{-0.006}M_\\odot$, and radii $5.392^{+0.018}_{-0.035}R_\\odot$ and $1.656^{+0.007}_{-0.044}R_\\odot$ for the primary and secondary stars, respectively. Because the primary star in the binary is rapidly evolving and is brighter than the cluster turnoff in a color-magnitude diagram, the measurement of its radius leads to a strong constraint on the cluster age. We find the age of M11 to be $222^{+2}_{-3}\\pm15$ Myr, where the quoted uncertainties come from statistical errors in the calculated masses and radii, and systematic uncertainties due to the ambiguity of...

  2. Portable treatment systems study

    Energy Technology Data Exchange (ETDEWEB)

    Sherick, M.J.; Schwinkendorf, W.E.; Bechtold, T.E.; Cole, L.T.

    1997-03-01

    In developing their Site Treatment Plans (STPs), many of the Department of Energy installations identified some form of portable treatment, to facilitate compliant disposition of select mixed low-level wastestreams. The Environmental Management Office of Science and Technology requested that a systems study be performed to better define the potential role of portable treatment with respect to mixed low-level waste, highlight obstacles to implementation, and identify opportunities for future research and development emphasis. The study was performed by first establishing a representative set of mixed waste, then formulating portable treatment system concepts to meet the required processing needs for these wastes. The portable systems that were conceptualized were evaluated and compared to a fixed centralized treatment alternative. The system evaluations include a life-cycle cost analysis and an assessment of regulatory, institutional, and technical issues associated with the potential use of portable systems. The results of this study show that when all costs are included, there are no significant cost differences between portable systems and fixed systems. However, it is also emphasized that many uncertainties exist that could impact the cost of implementing portable treatment systems. Portable treatment could be made more attractive through private sector implementation, although there is little economic incentive for a commercial vendor to develop small, specialized treatment capabilities with limited applicability. Alternatively, there may also be valid reasons why fixed units cannot be used for some problematic wastestreams. In any event, there are some site-specific problems that still need to be addressed, and there may be some opportunity for research and development to make a positive impact in these areas.

  3. Selective decontamination and antibiotic resistance in ICUs

    NARCIS (Netherlands)

    Plantinga, Nienke L.; Bonten, Marc J. M.

    2015-01-01

    Selective digestive decontamination (SDD) and selective oropharyngeal decontamination (SOD) have been associated with reduced mortality and lower ICU-acquired bacteremia and ventilator-associated pneumonia rates in areas with low levels of antibiotic resistance. However, the effect of selective deco

  4. [Decontamination of chemical and biological warfare agents].

    Science.gov (United States)

    Seto, Yasuo

    2009-01-01

    Chemical and biological warfare agents (CBWA's) are diverse in nature; volatile acute low-molecular-weight toxic compounds, chemical warfare agents (CWA's, gaseous choking and blood agents, volatile nerve gases and blister agents, nonvolatile vomit agents and lacrymators), biological toxins (nonvolatile low-molecular-weight toxins, proteinous toxins) and microbes (bacteria, viruses, rickettsiae). In the consequence management against chemical and biological terrorism, speedy decontamination of victims, facilities and equipment is required for the minimization of the damage. In the present situation, washing victims and contaminated materials with large volumes of water is the basic way, and additionally hypochlorite salt solution is used for decomposition of CWA's. However, it still remains unsolved how to dispose large volumes of waste water, and the decontamination reagents have serious limitation of high toxicity, despoiling nature against the environments, long finishing time and non-durability in effective decontamination. Namely, the existing decontamination system is not effective, nonspecifically affecting the surrounding non-target materials. Therefore, it is the urgent matter to build up the usable decontamination system surpassing the present technologies. The symposiast presents the on-going joint project of research and development of the novel decontamination system against CBWA's, in the purpose of realizing nontoxic, fast, specific, effective and economical terrorism on-site decontamination. The projects consists of (1) establishment of the decontamination evaluation methods and verification of the existing technologies and adaptation of bacterial organophosphorus hydrolase, (2) development of adsorptive elimination technologies using molecular recognition tools, and (4) development of deactivation technologies using photocatalysis.

  5. Electrochemical decontamination system for actinide processing gloveboxes

    Energy Technology Data Exchange (ETDEWEB)

    Wedman, D.E.; Lugo, J.L.; Ford, D.K.; Nelson, T.O.; Trujillo, V.L.; Martinez, H.E.

    1998-03-01

    An electrolytic decontamination technology has been developed and successfully demonstrated at Los Alamos National Laboratory (LANL) for the decontamination of actinide processing gloveboxes. The technique decontaminates the interior surfaces of stainless steel gloveboxes utilizing a process similar to electropolishing. The decontamination device is compact and transportable allowing it to be placed entirely within the glovebox line. In this way, decontamination does not require the operator to wear any additional personal protective equipment and there is no need for additional air handling or containment systems. Decontamination prior to glovebox decommissioning reduces the potential for worker exposure and environmental releases during the decommissioning, transport, and size reduction procedures which follow. The goal of this effort is to reduce contamination levels of alpha emitting nuclides for a resultant reduction in waste level category from High Level Transuranic (TRU) to low Specific Activity (LSA, less than or equal 100 nCi/g). This reduction in category results in a 95% reduction in disposal and disposition costs for the decontaminated gloveboxes. The resulting contamination levels following decontamination by this method are generally five orders of magnitude below the LSA specification. Additionally, the sodium sulfate based electrolyte utilized in the process is fully recyclable which results in the minimum of secondary waste. The process bas been implemented on seven gloveboxes within LANL`s Plutonium Facility at Technical Area 55. Of these gloveboxes, two have been discarded as low level waste items and the remaining five have been reused.

  6. INTEGRATED VERTICAL AND OVERHEAD DECONTAMINATION SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    M.A. Ebadian, Ph.D.

    1999-01-01

    This report summarizes the activities performed during FY98 and describes the planned activities for FY99. Accomplishments for FY98 include identifying and selecting decontamination, the screening of potential characterization technologies, development of minimum performance factors for the decontamination technology, and development and identification of Applicable, Relevant and Appropriate Regulations (ARARs).

  7. Managing mass casualties and decontamination.

    Science.gov (United States)

    Chilcott, Robert P

    2014-11-01

    Careful planning and regular exercising of capabilities is the key to implementing an effective response following the release of hazardous materials, although ad hoc changes may be inevitable. Critical actions which require immediate implementation at an incident are evacuation, followed by disrobing (removal of clothes) and decontamination. The latter can be achieved through bespoke response facilities or various interim methods which may utilise water or readily available (dry, absorbent) materials. Following transfer to a safe holding area, each casualty's personal details should be recorded to facilitate a health surveillance programme, should it become apparent that the original contaminant has chronic health effects.

  8. Comparison of skin decontamination efficacy of commercial decontamination products following exposure to VX on human skin.

    Science.gov (United States)

    Thors, L; Koch, M; Wigenstam, E; Koch, B; Hägglund, L; Bucht, A

    2017-08-01

    The decontamination efficacy of four commercially available skin decontamination products following exposure to the nerve agent VX was evaluated in vitro utilizing a diffusion cell and dermatomed human skin. The products included were Reactive Skin Decontamination Lotion (RSDL), the Swedish decontamination powder 104 (PS104), the absorbent Fuller's Earth and the aqueous solution alldecontMED. In addition, various decontamination procedures were assessed to further investigate important mechanisms involved in the specific products, e.g. decontamination removal from skin, physical removal by sponge swabbing and activation of degradation mechanisms. The efficacy of each decontamination product was evaluated 5 or 30 min after dermal application of VX (neat or diluted to 20% in water). The RSDL-lotion was superior in reducing the penetration of VX through human skin, both when exposed as neat agent and when diluted to 20% in water. Swabbing with the RSDL-sponge during 2 min revealed decreased efficacy compared to applying the RSDL-lotion directly on the skin for 30 min. Decontamination with Fuller's Earth and alldecontMED significantly reduced the penetration of neat concentration of VX through human skin. PS104-powder was insufficient for decontamination of VX at both time-points, independently of the skin contact time of PS104. The PS104-slurry (a mixture of PS104-powder and water), slightly improved the decontamination efficacy. Comparing the time-points for initiated decontamination revealed less penetrated VX for RSDL and Fuller's Earth when decontamination was initiated after 5 min compared to 30 min post-exposure, while alldecontMED displayed similar efficacy at both time-points. Decontamination by washing with water only resulted in a significant reduction of penetrated VX when washing was performed 5 min after exposure, but not when decontamination was delayed to 30 min post-exposure of neat VX. In conclusion, early initiated decontamination with the

  9. Strömgren-Hβ Photometry of the Galactic Open Cluster M11

    Science.gov (United States)

    Beaver, John; Briley, M. M.; Kaltcheva, N.; Conger, C.; Piehl, D.

    2013-01-01

    We present uvbyβ CCD photometry of the central region of the rich Galactic open cluster M11. Our study utilizes photometric data obtained with the 0.9-m WIYN telescope at the Kitt Peak National Observatory during two observing runs in 2007 and 2008. We match stars by position to identified stars in the WEBDA catalog and we compare our V and b-y observations to two previously-published data sets of V and B-V observations. From our photometry we identify nearly 250 stars earlier than spectral type A0 and we use them to derive a metallicity-independent average color excess and distance for the cluster. Our magnitude limit of V=17 allows us to reach late G spectral type and obtain accurate fits to the ZAMS in order to estimate the age of the cluster. Acknowledgements: this work was supported by NSF grants AST-0708950 and AST-1135760.

  10. Complete genome sequence of Thermosphaera aggregans type strain (M11TL).

    Science.gov (United States)

    Spring, Stefan; Rachel, Reinhard; Lapidus, Alla; Davenport, Karen; Tice, Hope; Copeland, Alex; Cheng, Jan-Fang; Lucas, Susan; Chen, Feng; Nolan, Matt; Bruce, David; Goodwin, Lynne; Pitluck, Sam; Ivanova, Natalia; Mavromatis, Konstantinos; Ovchinnikova, Galina; Pati, Amrita; Chen, Amy; Palaniappan, Krishna; Land, Miriam; Hauser, Loren; Chang, Yun-Juan; Jeffries, Cynthia C; Brettin, Thomas; Detter, John C; Tapia, Roxanne; Han, Cliff; Heimerl, Thomas; Weikl, Fabian; Brambilla, Evelyne; Göker, Markus; Bristow, James; Eisen, Jonathan A; Markowitz, Victor; Hugenholtz, Philip; Kyrpides, Nikos C; Klenk, Hans-Peter

    2010-06-15

    Thermosphaera aggregans Huber et al. 1998 is the type species of the genus Thermosphaera, which comprises at the time of writing only one species. This species represents archaea with a hyperthermophilic, heterotrophic, strictly anaerobic and fermentative phenotype. The type strain M11TL(T) was isolated from a water-sediment sample of a hot terrestrial spring (Obsidian Pool, Yellowstone National Park, Wyoming). Here we describe the features of this organism, together with the complete genome sequence and annotation. The 1,316,595 bp long single replicon genome with its 1,410 protein-coding and 47 RNA genes is a part of the Genomic Encyclopedia of Bacteria and Archaea project.

  11. Portable biochip scanner device

    Energy Technology Data Exchange (ETDEWEB)

    Perov, Alexander (Troitsk, RU); Sharonov, Alexei (Moscow, RU); Mirzabekov, Andrei D. (Darien, IL)

    2002-01-01

    A portable biochip scanner device used to detect and acquire fluorescence signal data from biological microchips (biochips) is provided. The portable biochip scanner device employs a laser for emitting an excitation beam. An optical fiber delivers the laser beam to a portable biochip scanner. A lens collimates the laser beam, the collimated laser beam is deflected by a dichroic mirror and focused by an objective lens onto a biochip. The fluorescence light from the biochip is collected and collimated by the objective lens. The fluorescence light is delivered to a photomultiplier tube (PMT) via an emission filter and a focusing lens. The focusing lens focuses the fluorescence light into a pinhole. A signal output of the PMT is processed and displayed.

  12. Deactivation, Decontamination and Decommissioning Project Summaries

    Energy Technology Data Exchange (ETDEWEB)

    Peterson, David Shane; Webber, Frank Laverne

    2001-07-01

    This report is a compilation of summary descriptions of Deactivation, Decontamination and Decommissioning, and Surveillance and Maintenance projects planned for inactive facilities and sites at the INEEL from FY-2002 through FY-2010. Deactivations of contaminated facilities will produce safe and stable facilities requiring minimal surveillance and maintenance pending further decontamination and decommissioning. Decontamination and decommissioning actions remove contaminated facilities, thus eliminating long-term surveillance and maintenance. The projects are prioritized based on risk to DOE-ID, the public, and the environment, and the reduction of DOE-ID mortgage costs and liability at the INEEL.

  13. Deactivation, Decontamination and Decommissioning Project Summaries

    Energy Technology Data Exchange (ETDEWEB)

    Peterson, David Shane; Webber, Frank Laverne

    2001-07-01

    This report is a compilation of summary descriptions of Deactivation, Decontamination and Decommissioning, and Surveillance and Maintenance projects planned for inactive facilities and sites at the INEEL from FY-2002 through FY-2010. Deactivations of contaminated facilities will produce safe and stable facilities requiring minimal surveillance and maintenance pending further decontamination and decommissioning. Decontamination and decommissioning actions remove contaminated facilities, thus eliminating long-term surveillance and maintenance. The projects are prioritized based on risk to DOE-ID, the public, and the environment, and the reduction of DOE-ID mortgage costs and liability at the INEEL.

  14. Portable Audio Design

    DEFF Research Database (Denmark)

    Groth, Sanne Krogh

    2014-01-01

    The chapter presents a methodological approach to the early process of producing portable audio design. The chapter high lights audio walks and audio guides, but can also be of inspiration when working with graphical and video production for portable devices. The final products can be presented...... within online and physical institutional contexts. The approach focuses especially on the relationship to specific sites, and how an awareness of the relationship between the site and the production can be part of the design process. Such awareness entails several approaches: the necessity of paying...

  15. Decontamination Efficacy Testing of COTS SteriFx Prodcuts for Mass Personnel and Casualty Decontamination

    Science.gov (United States)

    2011-09-01

    Water‐based decontamination technologies (e.g. soap and water) facilitate removal of the biological agent from skin, but have little effect on the...runoff from personnel decontamination is still biologically hazardous. Spores and bacterial cells will be prepared for the decontamination...of the stimulants will be compared to evaluate the disinfection efficacy of the technology on bacterial cells and spores. The minimum time to reach

  16. Radiation decontamination of poultry viscera

    Energy Technology Data Exchange (ETDEWEB)

    Jamdar, S.N. [Food Technology Division, FIPLY, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India)], E-mail: snjam2@yahoo.com; Harikumar, P. [Food Technology Division, FIPLY, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India)

    2008-04-15

    Application of gamma radiation for decontamination of poultry viscera was examined. Exposure to a dose of 20 kGy rendered the viscera sterile (<1 CFU/10 g tissue), while 5 and 10 kGy reduced the total bacterial count by 4 and 6 log{sub 10} cycles, respectively, eliminating the coliforms to <1 CFU/g of tissue. Analysis of organoleptic and biochemical parameters [proximate composition, total volatile basic nitrogen (TVBN), lipid peroxidation (TBARS value), and levels of TCA soluble peptides and proteolytic enzyme] showed that gamma irradiation (20 kGy) followed by storage at 4 deg. C for 62 days induced no significant change (except lipid peroxidation) in the acceptability of poultry viscera. However, storage at ambient temperature (26 {sup o}C) produced enhanced levels of TVBN and TCA soluble products accompanied by higher drip loss. Activities of proteolytic enzymes, except acid protease, did not show any significant change during post-irradiation storage at either temperature.

  17. Radiation decontamination of poultry viscera

    Science.gov (United States)

    Jamdar, S. N.; Harikumar, P.

    2008-04-01

    Application of gamma radiation for decontamination of poultry viscera was examined. Exposure to a dose of 20 kGy rendered the viscera sterile (TVBN), lipid peroxidation (TBARS value), and levels of TCA soluble peptides and proteolytic enzyme] showed that gamma irradiation (20 kGy) followed by storage at 4 °C for 62 days induced no significant change (except lipid peroxidation) in the acceptability of poultry viscera. However, storage at ambient temperature (26 °C) produced enhanced levels of TVBN and TCA soluble products accompanied by higher drip loss. Activities of proteolytic enzymes, except acid protease, did not show any significant change during post-irradiation storage at either temperature.

  18. Structure and stellar content analysis of the open cluster M11 with 2MASS photometry

    CERN Document Server

    Santos, J F C; Bica, E

    2005-01-01

    An overall analysis of the structure and stellar content of M11 is presented, thanks to the wide-angle 2MASS spatial coverage. We derive photometric and structural parameters and discuss the spatial dependance of the luminosity and mass functions. Photometric parameters basically agree with previous ones mostly based on the optical. We obtained a core radius of 1.23pc and a tidal radius of 29pc. In particular, the cluster is populous enough so that the tidal radius could be obtained by fitting the three-parameter King profile to the radial distribution of stars. We analyzed the spatial distribution of mass functions, finding that the the slope changes from -0.73 in the core to +2.88 in the outer halo. The spatial distribution of mass function slopes derived from 2MASS agrees with that derived from optical CCD data, which further confirms the reliability of 2MASS data for future analyses of this kind at comparable observational limits. We detect mass segregation up to distances from the center of ~20arcmin. We...

  19. PORTABLE SOURCE OF RADIOACTIVITY

    Science.gov (United States)

    Goertz, R.C.; Ferguson, K.R.; Rylander, E.W.; Safranski, L.M.

    1959-06-16

    A portable source for radiogiaphy or radiotherapy is described. It consists of a Tl/sup 170/ or Co/sup 60/ source mounted in a rotatable tungsten alloy plug. The plug rotates within a brass body to positions of safety or exposure. Provision is made for reloading and carrying the device safely. (T.R.H.)

  20. Plasma Air Decontamination System (PADS) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed Plasma Air Decontamination System (PADS) is a trace contaminant control device based on non-thermal atmospheric pressure plasma technology that operates...

  1. Plasma Air Decontamination System (PADS) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed Plasma Air Decontamination System (PADS) is a trace contaminant control device based on non-thermal atmospheric-pressure plasma technology. Compared to...

  2. Decontamination of protective clothing against radioactive contamination.

    Science.gov (United States)

    Vošahlíková, I; Otáhal, P

    2014-11-01

    The aim of this study is to describe the experimental results of external surface mechanical decontamination of the studied materials forming selected suits. Seven types of personal protective suits declaring protection against radioactive aerosol contamination in different price ranges were selected for decontamination experiments. The outcome of this study is to compare the efficiency of a double-step decontamination process on various personal protective suits against radioactive contamination. A comparison of the decontamination effectiveness for the same type of suit, but for the different chemical mixtures ((140)La in a water-soluble or in a water-insoluble compound), was performed. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  3. Urban Decontamination Experience at Pripyat Ukraine - 13526

    Energy Technology Data Exchange (ETDEWEB)

    Paskevych, Sergiy [Institute for Safety Problems of Nuclear Power Plants, National Academy of Sciences of Ukraine, 36 a Kirova str. Chornobyl, Kiev region, 07200 (Ukraine); Voropay, Dmitry [Federal State Unitary Enterprise ' Russian State Center of Inventory and Registration and Real Estate - Federal Bureau of Technical Inventory' , 37-2 Bernadsky Prospekt, Moscow Russia 119415 (Russian Federation); Schmieman, Eric [Battelle Memorial Institute, PO Box 999 MSIN K6-90, Richland, WA 99352 (United States)

    2013-07-01

    This paper describes the efficiency of radioactive decontamination activities of the urban landscape in the town of Pripyat, Ukraine. Different methods of treatment for various urban infrastructure and different radioactive contaminants are assessed. Long term changes in the radiation condition of decontaminated urban landscapes are evaluated: 1. Decontamination of the urban system requires the simultaneous application of multiple methods including mechanical, chemical, and biological. 2. If a large area has been contaminated, decontamination of local areas of a temporary nature. Over time, there is a repeated contamination of these sites due to wind transport from neighboring areas. 3. Involvement of earth-moving equipment and removal of top soil by industrial method achieves 20-fold reduction in the level of contamination by radioactive substances, but it leads to large amounts of waste (up to 1500 tons per hectare), and leads to the re-contamination of treated areas due to scatter when loading, transport pollutants on the wheels of vehicles, etc.. (authors)

  4. Dismantling decontamination of research reactor equipment

    Energy Technology Data Exchange (ETDEWEB)

    Voronik, N. I.; Davydov, Yu. P.; Shatilo, N. N. [Institute of Radioecological Problems Belarus Ac. Sci., Minsk-Sosny (Belarus)

    1999-07-01

    The purpose of the work was to check applicability of the existing and new compositions for decontamination and their adjustment to the specific conditions dealing with operation of the research reactor. (author)

  5. PREFACE: EmerQuM 11: Emergent Quantum Mechanics 2011 (Heinz von Foerster Congress)

    Science.gov (United States)

    Grössing, Gerhard

    2012-05-01

    These proceedings comprise the plenary lectures and poster contributions of the 'Heinz von Foerster Conference 2011' on Emergent Quantum Mechanics (EmerQuM11), which was held at the University of Vienna, 11-13 November 2011. With the 5th International Heinz von Foerster Conference convened at the occasion of von Foerster's 100th birthday, the organizers opted for a twin conference to take place at the Large and Small Ceremonial Halls of the University's main building, respectively. The overall topic was chosen as 'Self-Organization and Emergence', a topic to which von Foerster was an early contributor. While the first conference ('Self-Organization and Emergence in Nature and Society') addressed a more general audience, the second one ('Emergent Quantum Mechanics') was intended as a specialist meeting with a contemporary topic that could both serve as an illustration of von Foerster's intellectual heritage and, more generally, point towards future directions in physics. We thus intended to bring together many of those physicists who are interested in or are working on attempts to understand quantum mechanics as emerging from a suitable classical (or, more generally, deeper level) physics. EmerQuM11 was organized by the Austrian Institute for Nonlinear Studies (AINS), with essential support from the Wiener Institute for Social Science Documentation and Methodology (WISDOM), the Department of Contemporary History at the University of Vienna, and the Heinz von Foerster-Gesellschaft. There were a number of individuals who contributed to the smooth course of our meeting and whom I would like to sincerely thank: Christian Bischof, Thomas Elze, Marianne Ertl, Gertrud Hafner, Werner Korn, Angelika Krawanja, Florian Krug and his team, Sonja Lang, Albert Müller, Ilse Müller, Irene Müller, Karl Müller, Armin Reautschnig, Marion Schirrmacher, Anton Staudinger, Roman Zlabinger, and, last but not least, my AINS colleagues Siegfried Fussy, Herbert Schwabl and Johannes Mesa

  6. Decontamination Efficacy and Skin Toxicity of Two Decontaminants against Bacillus anthracis.

    Directory of Open Access Journals (Sweden)

    Chad W Stratilo

    Full Text Available Decontamination of bacterial endospores such as Bacillus anthracis has traditionally required the use of harsh or caustic chemicals. The aim of this study was to evaluate the efficacy of a chlorine dioxide decontaminant in killing Bacillus anthracis spores in solution and on a human skin simulant (porcine cadaver skin, compared to that of commonly used sodium hypochlorite or soapy water decontamination procedures. In addition, the relative toxicities of these decontaminants were compared in human skin keratinocyte primary cultures. The chlorine dioxide decontaminant was similarly effective to sodium hypochlorite in reducing spore numbers of Bacillus anthracis Ames in liquid suspension after a 10 minute exposure. After five minutes, the chlorine dioxide product was significantly more efficacious. Decontamination of isolated swine skin contaminated with Bacillus anthracis Sterne with the chlorine dioxide product resulted in no viable spores sampled. The toxicity of the chlorine dioxide decontaminant was up to two orders of magnitude less than that of sodium hypochlorite in human skin keratinocyte cultures. In summary, the chlorine dioxide based decontaminant efficiently killed Bacillus anthracis spores in liquid suspension, as well as on isolated swine skin, and was less toxic than sodium hypochlorite in cultures of human skin keratinocytes.

  7. Decontamination Efficacy and Skin Toxicity of Two Decontaminants against Bacillus anthracis.

    Science.gov (United States)

    Stratilo, Chad W; Crichton, Melissa K F; Sawyer, Thomas W

    2015-01-01

    Decontamination of bacterial endospores such as Bacillus anthracis has traditionally required the use of harsh or caustic chemicals. The aim of this study was to evaluate the efficacy of a chlorine dioxide decontaminant in killing Bacillus anthracis spores in solution and on a human skin simulant (porcine cadaver skin), compared to that of commonly used sodium hypochlorite or soapy water decontamination procedures. In addition, the relative toxicities of these decontaminants were compared in human skin keratinocyte primary cultures. The chlorine dioxide decontaminant was similarly effective to sodium hypochlorite in reducing spore numbers of Bacillus anthracis Ames in liquid suspension after a 10 minute exposure. After five minutes, the chlorine dioxide product was significantly more efficacious. Decontamination of isolated swine skin contaminated with Bacillus anthracis Sterne with the chlorine dioxide product resulted in no viable spores sampled. The toxicity of the chlorine dioxide decontaminant was up to two orders of magnitude less than that of sodium hypochlorite in human skin keratinocyte cultures. In summary, the chlorine dioxide based decontaminant efficiently killed Bacillus anthracis spores in liquid suspension, as well as on isolated swine skin, and was less toxic than sodium hypochlorite in cultures of human skin keratinocytes.

  8. Decontamination tests on cotton materials; Essais de decontamination sur tissus de coton

    Energy Technology Data Exchange (ETDEWEB)

    Cohen, P.; Pelletier, C. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    It is shown that versene gives the best decontamination results on cotton materials soiled by a mixture of fission products. (author) [French] On a montre que le versene donne les meilleurs resultats de decontamination sur des tissus de coton souilles par un melange de produits de fission. (auteur)

  9. Reactive skin decontamination lotion (RSDL) for the decontamination of chemical warfare agent (CWA) dermal exposure.

    Science.gov (United States)

    Schwartz, M D; Hurst, C G; Kirk, M A; Reedy, S J D; Braue, E H

    2012-08-01

    Rapid decontamination of the skin is the single most important action to prevent dermal absorption of chemical contaminants in persons exposed to chemical warfare agents (CWA) and toxic industrial chemicals (TICs) as a result of accidental or intentional release. Chemicals on the skin may be removed by mechanical means through the use of dry sorbents or water. Recent interest in decontamination systems which both partition contaminants away from the skin and actively neutralize the chemical has led to the development of several reactive decontamination solutions. This article will review the recently FDA-approved Reactive Skin Decontamination Lotion (RSDL) and will summarize the toxicity and efficacy studies conducted to date. Evidence of RSDL's superior performance against vesicant and organophosphorus chemical warfare agents compared to water, bleach, and dry sorbents, suggests that RSDL may have a role in mass human exposure chemical decontamination in both the military and civilian arenas.

  10. Portable Planetariums Teach Science

    Science.gov (United States)

    2015-01-01

    With the Internet proving to be the wave of the future, in the 1990s Johnson Space Center awarded grants to Rice University in Houston for developing the world's first Internet-accessible museum kiosk. Further grants were awarded to the school for creating educational software for use in homes and schools, leading to the creation of Museums Teaching Planet Earth Inc. The company has gone on to develop and sell portable planetariums and accompanying educational shows.

  11. Smart portable rehabilitation devices

    OpenAIRE

    Leahey Matt; Arango Roberto; Stuart Ryan; Prugnarola Jennifer; Pelletier Philip; Jensen Katherine; Danaher Gil; Weinberg Brian; Nikitczuk Jason; Mavroidis Constantinos; Pavone Robert; Provo Andrew; Yasevac Dan

    2005-01-01

    Abstract Background The majority of current portable orthotic devices and rehabilitative braces provide stability, apply precise pressure, or help maintain alignment of the joints with out the capability for real time monitoring of the patient's motions and forces and without the ability for real time adjustments of the applied forces and motions. Improved technology has allowed for advancements where these devices can be designed to apply a form of tension to resist motion of the joint. Thes...

  12. MRSA decontamination using octenidine-based products.

    Science.gov (United States)

    Danilevicius, Mindaugas; Juzéniené, Audra; Juzénaité-Karneckiené, Indré; Veršinina, Anželika

    Methicillin-resistant Staphylococcus aureus (MRSA) infections are an increasing problem worldwide with a high risk of severe illness and mortality in hospitalised patients. Patients with chronic wounds are at particular risk of developing MRSA infections. As octenidine-based products have shown promising success in decontamination in the past, the aim of the present study was to determine its efficacy, safety, and tolerability in decontaminating hospitalised MRSA-positive patients. From 1 April 2011 until 9 November 2012, 36 patients were screened MRSA-positive at the Republican Vilnius University Hospital, Vilnius, Lithuania. At least three swab tests were performed for each patient to screen for MRSA, one from each nostril and one from the perineum. In patients with wounds, an additional swab was taken from the wound surface. In the affected patients octenidine-based products were used in one or two cycles of 7 days each. In addition, adverse events were recorded and the tolerability was assessed using a 4-point scale ranging from 'very good' to 'poor'. Complete decontamination was achieved in 24 patients (67%) following treatment with the octenidine-based products. None of the patients experienced side-effects or secondary symptoms such as skin irritation or allergic reactions during the course of the study. In addition, octenidine was very well tolerated in the majority of patients (n=31; 86%). The results demonstrate that octenidine-based products are highly efficient in the multifaceted decontamination of hospitalised MRSA-positive patients. Having a range of products that can be used for full body decontamination (including the scalp and nasal passages) is of particular significance when developing an MRSA decontamination protocol, as multiple parts of the body can be affected. Combined with a favourable safety and tolerability profile, octenidine-based products thus represent a good choice in multifaceted MRSA decontamination regimes, which are necessary to

  13. Remotely operated decontamination systems for use in DFDF

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ki Ho; Park, Jang Jin; Yang, Myung Seung [KAERI, Taejon (Korea, Republic of)

    2003-07-01

    This paper presents the development of the remotely operated decontamination systems for use in a highly radioactive zone of the DUPIC Fuel Development Facility of the Irradiated Material Examination Facility at the Korea Atomic Energy Research Institute. The remotely operated decontamination systems were designed to completely eliminate human interaction with hazardous radioactive contaminants. These decontamination systems are mainly classified into three systems depending on the task environment- a fabrication equipment decontamination system, a hot-cell floor decontamination system, and an isolation room floor decontamination system. A decontamination system for contaminated fabrication equipment utilizes dry ice pellet blasting method to decontaminate contaminated surface of the equipment. The decontamination systems for the hot-cell floor and isolation room floor employ a vacuum cleaning method to decontaminate the contaminated floor and collect loose dry spent nuclear fuel debris and other radioactive waste placed on the floor. The human operator from the out-of-cell performs a series of decontamination tasks remotely by manipulating decontamination systems located in-cell via a hand controller with the aid of vision feedback information. The environmental, functional and mechanical design considerations, control system and capabilities of the remotely operated decontamination systems at a high radioactive environment are also described.

  14. Smart portable rehabilitation devices

    Directory of Open Access Journals (Sweden)

    Leahey Matt

    2005-07-01

    Full Text Available Abstract Background The majority of current portable orthotic devices and rehabilitative braces provide stability, apply precise pressure, or help maintain alignment of the joints with out the capability for real time monitoring of the patient's motions and forces and without the ability for real time adjustments of the applied forces and motions. Improved technology has allowed for advancements where these devices can be designed to apply a form of tension to resist motion of the joint. These devices induce quicker recovery and are more effective at restoring proper biomechanics and improving muscle function. However, their shortcoming is in their inability to be adjusted in real-time, which is the most ideal form of a device for rehabilitation. This introduces a second class of devices beyond passive orthotics. It is comprised of "active" or powered devices, and although more complicated in design, they are definitely the most versatile. An active or powered orthotic, usually employs some type of actuator(s. Methods In this paper we present several new advancements in the area of smart rehabilitation devices that have been developed by the Northeastern University Robotics and Mechatronics Laboratory. They are all compact, wearable and portable devices and boast re-programmable, real time computer controlled functions as the central theme behind their operation. The sensory information and computer control of the three described devices make for highly efficient and versatile systems that represent a whole new breed in wearable rehabilitation devices. Their applications range from active-assistive rehabilitation to resistance exercise and even have applications in gait training. The three devices described are: a transportable continuous passive motion elbow device, a wearable electro-rheological fluid based knee resistance device, and a wearable electrical stimulation and biofeedback knee device. Results Laboratory tests of the devices

  15. Smart portable rehabilitation devices.

    Science.gov (United States)

    Mavroidis, Constantinos; Nikitczuk, Jason; Weinberg, Brian; Danaher, Gil; Jensen, Katherine; Pelletier, Philip; Prugnarola, Jennifer; Stuart, Ryan; Arango, Roberto; Leahey, Matt; Pavone, Robert; Provo, Andrew; Yasevac, Dan

    2005-07-12

    The majority of current portable orthotic devices and rehabilitative braces provide stability, apply precise pressure, or help maintain alignment of the joints with out the capability for real time monitoring of the patient's motions and forces and without the ability for real time adjustments of the applied forces and motions. Improved technology has allowed for advancements where these devices can be designed to apply a form of tension to resist motion of the joint. These devices induce quicker recovery and are more effective at restoring proper biomechanics and improving muscle function. However, their shortcoming is in their inability to be adjusted in real-time, which is the most ideal form of a device for rehabilitation. This introduces a second class of devices beyond passive orthotics. It is comprised of "active" or powered devices, and although more complicated in design, they are definitely the most versatile. An active or powered orthotic, usually employs some type of actuator(s). In this paper we present several new advancements in the area of smart rehabilitation devices that have been developed by the Northeastern University Robotics and Mechatronics Laboratory. They are all compact, wearable and portable devices and boast re-programmable, real time computer controlled functions as the central theme behind their operation. The sensory information and computer control of the three described devices make for highly efficient and versatile systems that represent a whole new breed in wearable rehabilitation devices. Their applications range from active-assistive rehabilitation to resistance exercise and even have applications in gait training. The three devices described are: a transportable continuous passive motion elbow device, a wearable electro-rheological fluid based knee resistance device, and a wearable electrical stimulation and biofeedback knee device. Laboratory tests of the devices demonstrated that they were able to meet their design

  16. Portable radiation detector and mapping system

    Energy Technology Data Exchange (ETDEWEB)

    Hofstetter, K.J.; Hayes, D.W.; Eakle, R.F. [Westinghouse Savannah River Company, Aiken, SC (United States)

    1995-12-31

    A portable radiation detector and mapping system (RADMAPS) has been developed to detect, locate, and plot nuclear radiation intensities on commercially available digital maps and other images. The field unit records gamma-ray spectra or neutron signals together with positions from a global positioning system (GPS) on flash memory cards. The recorded information is then transferred to a laptop computer for spectral data analyses and then georegistered graphically on maps, photographs, etc. RADMAPS integrates several existing technologies to produce a preprogrammable field unit uniquely suited for each survey, as required. The system records spectra from a NaI(Tl) gamma-ray detector or an enriched {sup 6}Li doped glass neutron scintillator. Standard Geographic Information System (GIS) software installed in a lap-top, complete with CD-ROM supporting digitally imaged maps, permits the characterization of nuclear material in the field when the presence of such material is not otherwise documented. This paper gives the results of a typical site survey of the Savannah River site (SRS) using RADMAPS. The ability to provide rapid field data should be of use in treaty verification, safeguards, decontamination, and nuclear weapons dismantlement.

  17. Chemical Warfare Agent Degradation and Decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Talmage, Sylvia Smith [ORNL; Watson, Annetta Paule [ORNL; Hauschild, Veronique [U.S. Environmental Protection Agency; Munro, Nancy B [ORNL; King, J. [U.S. Army Environmental Center

    2007-02-01

    The decontamination of chemical warfare agents (CWA) from structures, environmental media, and even personnel has become an area of particular interest in recent years due to increased homeland security concerns. In addition to terrorist attacks, scenarios such as accidental releases of CWA from U.S. stockpile sites or from historic, buried munitions are also subjects for response planning. To facilitate rapid identification of practical and effective decontamination approaches, this paper reviews pathways of CWA degradation by natural means as well as those resulting from deliberately applied solutions and technologies; these pathways and technologies are compared and contrasted. We then review various technologies, both traditional and recent, with some emphasis on decontamination materials used for surfaces that are difficult to clean. Discussion is limited to the major threat CWA, namely sulfur mustard (HD, bis(2-chloroethyl)sulfide), VX (O-ethyl S-(2-diisopropylaminoethyl) methylphosphonothioate), and the G-series nerve agents. The principal G-agents are GA (tabun, ethyl N,N-dimethylphosphoramidocyanidate), GB (sarin, isopropyl methylphosphonofluoridate), and GD (soman, pinacolyl methylphosphonofluoridate). The chemical decontamination pathways of each agent are outlined, with some discussion of intermediate and final degradation product toxicity. In all cases, and regardless of the CWA degradation pathway chosen for decontamination, it will be necessary to collect and analyze pertinent environmental samples during the treatment phase to confirm attainment of clearance levels.

  18. Civilian First Responder Decontamination Equipment Characteristics Survey Results

    Science.gov (United States)

    2010-01-01

    of Standards and Technology (DHS/NIST) Standards Development Team to develop a survey to determine important characteristics of first responder decontamination...a draft American Society for Testing Materials standard for civilian first responder decontamination systems.

  19. Radio-decontamination efficacy and safety studies on optimized decontamination lotion formulation.

    Science.gov (United States)

    Rana, S; Bhatt, S; Dutta, M; Khan, A W; Ali, J; Sultana, S; Kotta, S; Ansari, S H; Sharma, R K

    2012-09-15

    Objective of the present study was to optimize decontamination lotion and to evaluate its relative decontamination efficacy using three radio-isotopes (Technetium-99m, Iodine-131 and Thallium-201) as contaminants with varying length of contaminant exposure (0-1h). Experiments were performed on Sprague Dawley rat's intact skin and human tissue equivalent models. Rat's hair was removed by using depilator after trimming with scissors. Relative decontamination efficacy of the optimized lotion was investigated and compared with water as control. Static counts were recorded before and after decontamination using single photon emission computed tomography (SPECT). Measured decontamination efficacy (DE) values were analyzed using one way ANOVA and Student's t-test (p valueDecontamination efficacy of the lotion was observed to be 90 ± 5%, 80 ± 2% and 85 ± 2%, for the (131)I, (201)Tl and (99m)Tc radio-contaminants respectively on skin. Reduced contaminant removal was recorded for the skin which was cleaned by depilator (50-60%). Skin decontamination was found more efficacious for rat skin decontamination than the human tissue equivalent model. Decontamination efficacy of the lotion against (99m)Tc was recorded 70 ± 15% at 0-1h on the tissue equivalent model. In vitro chelation efficacy of the lotion was also established by using the instant thin layer chromatography-slica gel (ITLC-SG) and >95% of (99m)Tc was recorded. Neither erythema nor edema was scored in the primary skin irritancy test visually observed for two weeks.

  20. Surface decontamination using dry ice snow

    Energy Technology Data Exchange (ETDEWEB)

    Ryu, Jungdong; Park, Kwangheon [College of Mechnical and Industrial System Engineering, Kyunghee University, Yongin (Korea, Republic of); Lee, Bumsik; Kim Yangeun [Wolsung Nuclear Power Plants, KEPCO (Korea, Republic of)

    1999-07-01

    An adjustable nozzle for controlling the size of dry ice snow was developed. The converging/diverging nozzle can control the size of snows from sub-microns to 10 micron size. Using the nozzle, a surface decontamination device was made. The removal mechanisms of surface contaminants are mechanical impact, partial dissolving and evaporation process, and viscous flow. A heat supply system is added for the prevention of surface ice layer formation. The cleaning power is slightly dependent on the size of snow. Small snows are the better in viscous flow cleaning, while large snows are slightly better in dissolving and sublimation process. Human oils like fingerprints on glass were easy to remove. Decontamination ability was tested using a contaminated pump-housing surface. About 40 to 80% of radioactivity was removed. This device is effective in surface-decontamination of any electrical devices like detector, controllers which cannot be cleaned in aqueous solution. (author)

  1. DECONTAMINATION AND BENEFICIAL USE OF DREDGED MATERIALS.

    Energy Technology Data Exchange (ETDEWEB)

    STERN, E.A.; LODGE, J.; JONES, K.W.; CLESCERI, N.L.; FENG, H.; DOUGLAS, W.S.

    2000-12-03

    Our group is leading a large-sale demonstration of dredged material decontamination technologies for the New York/New Jersey Harbor. The goal of the project is to assemble a complete system for economic transformation of contaminated dredged material into an environmentally-benign material used in the manufacture of a variety of beneficial use products. This requires the integration of scientific, engineering, business, and policy issues on matters that include basic knowledge of sediment properties, contaminant distribution visualization, sediment toxicity, dredging and dewatering techniques, decontamination technologies, and product manufacturing technologies and marketing. A summary of the present status of the system demonstrations including the use of both existing and new manufacturing facilities is given here. These decontamination systems should serve as a model for use in dredged material management plans of regions other than NY/NJ Harbor, such as Long Island Sound, where new approaches to the handling of contaminated sediments are desirable.

  2. Physicians' and nurses' opinions on selective decontamination of the digestive tract and selective oropharyngeal decontamination : a survey

    NARCIS (Netherlands)

    Jongerden, Irene P.; de Smet, Anne Marie G.; Kluytmans, Jan A.; Velde, Leo F. Te; Dennesen, Paul J.; Wesselink, Ronald M.; Bouw, Martijn P.; Spanjersberg, Rob; Bogaers-Hofman, Diana; van der Meer, Nardo J.; de Vries, Jaap W.; Kaasjager, Karin; van Iterson, Mat; Kluge, Georg H.; van der Werf, Tjip S.; Harinck, Hubertus I.; Bindels, Alexander J.; Pickkers, Peter; Bonten, Marc J.

    2010-01-01

    Introduction: Use of selective decontamination of the digestive tract (SDD) and selective oropharyngeal decontamination (SOD) in intensive care patients has been controversial for years. Through regular questionnaires we determined expectations concerning SDD (effectiveness) and experience with SDD

  3. Physicians' and nurses' opinions on selective decontamination of the digestive tract and selective oropharyngeal decontamination: a survey.

    NARCIS (Netherlands)

    Jongerden, I.P.; Smet, A.M. de; Kluytmans, J.A.; Velde, L.F. te; Dennesen, P.J.; Wesselink, R.M.; Bouw, M.P.W.J.M.; Spanjersberg, R.; Bogaers-Hofman, D.; Meer, N.J. van der; Vries, J.W. de; Kaasjager, K.; Iterson, M. van; Kluge, G.H.; Werf, T.S. van der; Harinck, H.I.; Bindels, A.J.; Pickkers, P.; Bonten, M.J.

    2010-01-01

    INTRODUCTION: Use of selective decontamination of the digestive tract (SDD) and selective oropharyngeal decontamination (SOD) in intensive care patients has been controversial for years. Through regular questionnaires we determined expectations concerning SDD (effectiveness) and experience with SDD

  4. T55-L-714 Engine Development and Qualification. Engine M11 Low Cycle Fatigue Test Report. (0213-005-87),

    Science.gov (United States)

    1987-12-01

    feature items) that are or may be scheduled for inclusion in production engines and which may be sensitive to this type of cycling. Engine M-11 testing was...Remove SGB seal 2-300-138-01 and install seal R. Willard 2-300-138-02G. M. Wolfram M. Zoccoli 2.4) Check balance GP rotors, correct as necessary to

  5. Attempt of portable HLS

    Energy Technology Data Exchange (ETDEWEB)

    Matsui, S. [Japan Synchrotron Radiation Research Institute, JASRI, Hyogo (Japan)

    1999-07-01

    This article presents the work that has been made to get a reliable magnet level surveys of the Spring-8 ring. The hydrostatic level system (HLS) completed with a capacitive sensor of water surface, has been used. If the length is about 20 m and the inner diameter of the water pipe is 10 mm, the decay time is stable within a few minutes after the sensor was set on stage. Thus the portable HLS is convenient for measuring points between the reference level ones.

  6. Possibilities of plasma decontamination at atmospheric pressure

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Masaaki; Windarto, Hendri; Matsumoto, Takeshi; Akatsuka, Hiroshi [Tokyo Institute of Technology, Tokyo (Japan); Sakagishi, Kohji [ATOX Co., Ltd., Chiba (Japan)

    1999-07-01

    The highly effective decontamination process by using atmospheric pressure plasma is proposed. The microwave plasma generator, which we designed, is suitable for discharge of molecular gas and it has a special feature as a source of high concentration reactive atoms in the discharge o molecular gases rather than a plasma source. To demonstrate this idea and discuss about its possibility, some cold experiments were carried out. Our experimental results shows the high effectiveness and it can be concluded consequently that the proposed process has the possibility of the practical processing with having the advantage of plasma decontamination technique which have been investigated under the low pressure conditions. (author)

  7. Reaction-diffusion models of decontamination

    DEFF Research Database (Denmark)

    Hjorth, Poul G.

    A contaminant, which also contains a polymer is in the form of droplets on a solid surface. It is to be removed by the action of a decontaminant, which is applied in aqueous solution. The contaminant is only sparingly soluble in water, so the reaction mechanism is that it slowly dissolves...... in the aqueous solution and then is oxidized by the decontaminant. The polymer is insoluble in water, and so builds up near the interface, where its presence can impede the transport of contaminant. In these circumstances, Dstl wish to have mathematical models that give an understanding of the process, and can...

  8. Green coffee decontamination by electron beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Nemtanu, Monica R. [National Institute for Lasers, Plasma and Radiation Physics, Department of Electron Accelerators, 409 Atomistilor St., P.O. Box MG-36, RO 76 900, Bucharest-Magurele (Romania)]. E-mail: monica@infim.ro; Brasoveanu, Mirela [National Institute for Lasers, Plasma and Radiation Physics, Department of Electron Accelerators, 409 Atomistilor St., P.O. Box MG-36, RO 76 900, Bucharest-Magurele (Romania); Grecu, Maria Nicoleta [National Institute for Materials Physics, RO 77 125, Bucharest-Magurele (Romania); Minea, R. [National Institute for Lasers, Plasma and Radiation Physics, Department of Electron Accelerators, 409 Atomistilor St., P.O. Box MG-36, RO 76 900, Bucharest-Magurele (Romania)

    2005-10-15

    Microbiological load of green coffee is a real problem considering that it is extremely sensitive to contamination. Irradiation is a decontamination method for a lot of foodstuffs, being a feasible, very effective and environment friendly one. Beans and ground green coffee were irradiated with electron beams up to 40 kGy. Microbial load, rheological behavior, electron paramagnetic resonance (EPR) and visible spectroscopy were carried out. The results show that electron beam irradiation of green coffee could decontaminate it without severe changes in its properties.

  9. Green coffee decontamination by electron beam irradiation

    Science.gov (United States)

    Nemtanu, Monica R.; Brasoveanu, Mirela; Grecu, Maria Nicoleta; Minea, R.

    2005-10-01

    Microbiological load of green coffee is a real problem considering that it is extremely sensitive to contamination. Irradiation is a decontamination method for a lot of foodstuffs, being a feasible, very effective and environment friendly one. Beans and ground green coffee were irradiated with electron beams up to 40 kGy. Microbial load, rheological behavior, electron paramagnetic resonance (EPR) and visible spectroscopy were carried out. The results show that electron beam irradiation of green coffee could decontaminate it without severe changes in its properties.

  10. Portable Virtual Training Units

    Science.gov (United States)

    Malone, Reagan; Johnston, Alan

    2015-01-01

    The Mission Operations Lab initiated a project to design, develop, deliver, test, and validate a unique training system for astronaut and ground support personnel. In an effort to keep training costs low, virtual training units (VTUs) have been designed based on images of actual hardware and manipulated by a touch screen style interface for ground support personnel training. This project helped modernized the training system and materials by integrating them with mobile devices for training when operators or crew are unavailable to physically train in the facility. This project also tested the concept of a handheld remote device to control integrated trainers using International Space Station (ISS) training simulators as a platform. The portable VTU can interface with the full-sized VTU, allowing a trainer co-located with a trainee to remotely manipulate a VTU and evaluate a trainee's response. This project helped determine if it is useful, cost effective, and beneficial for the instructor to have a portable handheld device to control the behavior of the models during training. This project has advanced NASA Marshall Space Flight Center's (MSFC's) VTU capabilities with modern and relevant technology to support space flight training needs of today and tomorrow.

  11. Decontamination of cephalosporin-resistant Enterobacteriaceae during selective digestive tract decontamination in intensive care units

    NARCIS (Netherlands)

    Oostdijk, E.A.; Smet, A.M. de; Kesecioglu, J.; Bonten, M.J.; Hoeven, J.G. van der; Pickkers, P.; Sturm, P.D.; Voss, A.

    2012-01-01

    OBJECTIVES: Prevalences of cephalosporin-resistant Enterobacteriaceae are increasing globally, especially in intensive care units (ICUs). The effect of selective digestive tract decontamination (SDD) on the eradication of cephalosporin-resistant Enterobacteriaceae from the intestinal tract is unknow

  12. Decontamination of cephalosporin-resistant Enterobacteriaceae during selective digestive tract decontamination in intensive care units

    NARCIS (Netherlands)

    Oostdijk, Evelien A. N.; de Smet, Anne Marie G. A.; Kesecioglu, Jozef; Bonten, Marc J. M.

    2012-01-01

    Prevalences of cephalosporin-resistant Enterobacteriaceae are increasing globally, especially in intensive care units (ICUs). The effect of selective digestive tract decontamination (SDD) on the eradication of cephalosporin-resistant Enterobacteriaceae from the intestinal tract is unknown. We quanti

  13. A study on dry decontamination using ion exchange polymer

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Ki Jung; Ahn, Byung Gil

    1997-12-01

    Through the project of {sup A} study on dry decontamination using ion exchange polymer{sup ,} the followings were investigated. 1. Highly probable decontamination technologies for the decontamination were investigated. 2. Development of gel type decontamination agent using ion-exchange resin powder (mixed type) as an ion exchanger. 3. Manufacturing of contaminated specimens (5 kinds) with Cs-137 solution and dust / Cs-137 solution. 4. Decontamination performance evaluation of the manufactured agent. 5. Analysis of composition (XRF) and the structure of surface of specimens (optic micrography). (author). 20 refs., 11 figs.

  14. Study on the Decontamination of Radionuclides in Spent Phosphogypsum

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Chong Hun; Won, H. J.; Moon, J. K.

    2010-01-15

    The objective of the study is to confirm the possibility of further R and D thru pre-study on the decontamination technology for the safe, high decontamination factor, low waste arising and cost effective removal of radionuclide in spent phosphogypsum. The following contents were studied. 1) Decontamination of Radionuclide in Phosphogypsum - Effect of decontamination chemical formulation on Ra removal - Effect of H{sub 2}O{sub 2} concentration on Ra removal - Effect of Sr concentration on Ra removal 2) Removal of Radionuclide in Liquid Waste from Decontamination of Phosphogypsum - Ra removal by chromate treatment - Ra removal by zeolite and ACF treatment

  15. Hand decontamination: nurses' opinions and practices.

    Science.gov (United States)

    Gould, D

    Infection is spread in hospital mainly by hands, making hand decontamination the most important means of preventing dissemination. There is some evidence to suggest that when access to hand-decontaminating agents is poor or the agents available are disliked, hands are washed too seldom, increasing risks of cross-infection. However, little attention has been paid to the use of towels and factors which promote their use, although it is known that damp hands transfer bacteria more readily than dry ones and that hands which become sore through poor drying have higher bacterial counts, contributing to the risk of cross-infection. This paper reports the results of the Nursing Times Hand Drying survey designed to assess nurses' access to hand decontamination agents and towels. The results suggest that the 112 nurses who participated were aware of the need for attention to hand hygiene but that access to both hand-decontaminating agents and paper towels was variable. Forty-one per cent complained of a shortage of soap and although nearly all used paper towels, these were in many cases of poor quality. Such towels were perceived as damaging to hands, leaving them feeling damp and sore. Good-quality, soft, paper towels were much appreciated by respondents in this sample. It is concluded that the quality of paper towels contributes to good infection control practice.

  16. 40 CFR 170.250 - Decontamination.

    Science.gov (United States)

    2010-07-01

    ... pesticides into the tank. (3) The handler employer shall provide soap and single-use towels in quantities... vehicular access: (i) The soap, single-use towels, clean change of clothing, and water may be at the nearest..., streams, lakes, or other sources for decontamination at the remote work site, if such water is more...

  17. Decontamination and decommissioning focus area. Technology summary

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-06-01

    This report presents details of the facility deactivation, decommissioning, and material disposition research for development of new technologies sponsored by the Department of Energy. Topics discussed include; occupational safety, radiation protection, decontamination, remote operated equipment, mixed waste processing, recycling contaminated metals, and business opportunities.

  18. Solid waste handling and decontamination facility

    Energy Technology Data Exchange (ETDEWEB)

    Lampton, R. E.

    1979-01-01

    The Title 1 design of the decontamination part of the SWH and D facility is underway. Design criteria are listed. A flowsheet is given of the solid waste reduction. The incinerator scrubber is described. Design features of the Gunite Tank Sludge Removal and a schematic of the sluicer, TV camera, and recirculating system are given. 9 figures. (DLC)

  19. INTEGRATED VERTICAL AND OVERHEAD DECONTAMINATION (IVOD) SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    M.A. Ebadian, Ph.D.

    2001-01-01

    The deactivation and decommissioning of 1200 buildings within the U.S. Department of Energy-Office of Environmental Management complex will require the disposition of a large quantity of contaminated concrete and metal surfaces. It has been estimated that 23 million cubic meters of concrete and over 600,000 tons of metal will need disposition. The disposition of such large quantities of material presents difficulties in the area of decontamination and characterization. The final disposition of this large amount of material will take time and money as well as risk to the D&D work force. A single automated system that would decontaminate and characterize surfaces in one step would not only reduce the schedule and decrease cost during D&D operations but would also protect the D&D workers from unnecessary exposures to contaminated surfaces. This report summarizes the activities performed during FY00 and describes the planned activities for FY01. Accomplishments for FY00 include the following: Development and field-testing of characterization system; Completion of Title III design of deployment platform and decontamination unit; In-house testing of deployment platform and decontamination unit; Completion of system integration design; Identification of deployment site; and Completion of test plan document for deployment of IVOD at Rancho Seco nuclear power facility.

  20. Portability and networked learning environments

    NARCIS (Netherlands)

    Collis, B.A.; De Diana, I.P.F.

    1994-01-01

    Abstract The portability of educational software is defined as the likelihood of software usage, with or without adaptation, in an educational environment different from that for which it was originally designed and produced. Barriers and research relevant to the portability of electronic learning r

  1. Portable reinforcing timbering

    Energy Technology Data Exchange (ETDEWEB)

    Trukhin, P.M.; Kan, Ye.V.; Novikov, V.Ya.; Popov, K.P.; Rusyaykin, I.P.; Sardov, A.I.

    1984-01-01

    The purpose of the invention is to improve reliability and safety of the timbering. This goal is achieved because in the portable reinforcing timbering which contains a cross beam connected on the edges to the support elements interacting with the permanent timbering frames, hydrostands with supports, assemblies for connecting the hydrostands to the cross beam, the support elements are turned towards each other and are attached at the bottom by stands that rotate on the cross beam, while the connecting assemblies are made in the form of easily detachable clamps. The connecting assemblies of the hydrostands with cross beams are made in the form of a cantilever and walls interacting with the base of the cross beam through the vertical ribs with slits in the shape of the base of the cross beam and with the hydrostand by horizontal ribs, and among themselves by vertical ribs of the cantilever and vertical slits in the wall. In addition, the rapidly detachable connection of the cantilever to the wall is made in the form of a lever with short supports interacting with the vertical slits and the round openings in their upper section on the cantilever ribs, and the diameter of the lever axis and the round openings of the slits is greater than the diameter of the lever supports and the vertical slits of the cantilever, while the inner distance between the supports equals the outer distance between the vertical ribs of the cantilever.

  2. Portable Data Acquisition System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Armstrong researchers have developed a portable data acquisition system (PDAT) that can be easily transported and set up at remote locations to display and archive...

  3. 49 CFR 176.137 - Portable magazine.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Portable magazine. 176.137 Section 176.137... Requirements for Class 1 (Explosive) Materials Stowage § 176.137 Portable magazine. (a) Each portable magazine... wood, a portable magazine must be framed of nominal 5 cm × 10 cm (2×4 inch) lumber, and sheathed...

  4. Lotus LADM Based Self-Decontaminating Surfaces

    Science.gov (United States)

    2007-05-01

    angle on the prepared surfaces was measured with sessile water drops using a lab- designed goniometer at 20℃. The contact angle images were obtained... contact angles up to 178°. We have also developed Light Activated Decontamination Materials, LADM, that produce singlet oxygen. In addition a series of...materials. SELF-CLEANING SURFACES Superhydrophobic surfaces are defined as surfaces upon which water has an apparent contact angle of greater than

  5. Methods of decontaminating surfaces and related compositions

    Energy Technology Data Exchange (ETDEWEB)

    Demmer, Ricky L.; Crosby, Daniel; Norton, Christopher J.

    2016-11-22

    A composition of matter includes water, at least one acid, at least one surfactant, at least one fluoride salt, and ammonium nitrate. A method of decontaminating a surface includes exposing a surface to such a composition and removing the composition from the surface. Other compositions of matter include water, a fatty alcohol ether sulfate, nitrilotriacetic acid, at least one of hydrochloric acid and nitric acid, sodium fluoride, potassium fluoride, ammonium nitrate, and gelatin.

  6. Surface Decontamination of Blister Agents Lewisite, Sulfur ...

    Science.gov (United States)

    Journal Article Sulfur mustard (HD) and Lewisite (L) are blister agents that have a high potential for terrorist use. Agent Yellow (HL) is the eutectic mixture of HD and L. Bench-scale testing was used to determine the residual amount of these chemical warfare agents remaining on three building materials coupons (wood, metal and glass) after application of various decontaminants (household bleach, full strength and dilute; hydrogen peroxide 3 % solution; and EasyDECON® DF200).

  7. Advanced robotics for decontamination and dismantlement

    Energy Technology Data Exchange (ETDEWEB)

    Hamel, W.R.; Haley, D.C.

    1994-06-01

    The decontamination and dismantlement (D&D) robotics technology application area of the US Department of Energy`s Robotics Technology Development Program is explained and described. D&D robotic systems show real promise for the reduction of human exposure to hazards, for improvement of productivity, and for the reduction of secondary waste generation. Current research and development pertaining to automated floor characterization, robotic equipment removal, and special inspection is summarized. Future research directions for these and emerging activities is given.

  8. ET-46ONCOLYTIC VIRAL THERAPY FOR MALIGNANT GLIOMAS USING MYXOMA VIRUS DELETED FOR ANTI-APOPTOTIC M11L GENE

    Science.gov (United States)

    Pisklakova, Alexandra; McKenzie, Brienne; Kenchappa, Rajappa; McFadden, Grant; Forsyth, Peter

    2014-01-01

    Brain Tumour Initiating Cells (BTICs) are stem-like cells hypothesized to mediate recurrence in high-grade gliomas. Myxoma virus (MyxV) is a promising oncolytic virus, which is highly effective in conventional long term resistant glioma cell lines and less effective in BTICs. We hypothesized that one possible factor limiting efficacy in BTICs is that cell death following infection with MyxV is inhibited by virally encoded anti-apoptotic proteins, such as the Bcl-2 structural homologue, M011L. To test this we evaluated and compared the efficacy of wtMYXV versus the viral construct MyxV-M011L-KO (in which the anti-apoptotic protein M11L has been deleted) in BTICs. We found that WT-MyxV does not induce significant level of apoptosis in infected BTICs, but that MyxV-M011L-KO induces dramatically more apoptosisas shown by caspase activation, PARP cleavage, and Cytochrome C release from the mitochondria M11L from the WT-MyxV localized to the mitochondrial membrane and prevented the association of Bax with the mitochondrial membrane. Finally, silencing of Bax using specific siRNAs significantly blocked the induction of apoptosis and cell death that occurs after infection with mutant MyxV-M011L-KO virus. Therefore MyxV-M011L-KO, which is has the anti-apoptotic virally derived gene M11L, dramatically improves the oncolytic efficacy in BTICs and this is dependent on the presence of the pro-apoptotic host protein, Bax. This is the first demonstration, that the MyxV mutant, genetically modified to promote apoptosis in tumor initiating cells, is significantly more efficacious than the wildtype virus. Strategies, such as this one, that promotes apoptosis in tumor initiating cells might be particularly effective.

  9. Metallic surfaces decontamination by using laser light

    Energy Technology Data Exchange (ETDEWEB)

    Moggia, Fabrice [AREVA, Back End Business Group, Clean-Up Business Unit, Gif-sur-Yvette (France); Lecardonnel, Xavier [AREVA, Back End Business Group, Clean-Up Business Unit,La Hague (France)

    2013-07-01

    Metal surface cleaning appears to be one of the major priorities for industries especially for nuclear industries. The research and the development of a new technology that is able to meet the actual requirements (i.e. waste volume minimization, liquid effluents and chemicals free process...) seems to be the main commitment. Currently, a wide panel of technologies already exists (e.g. blasting, disk sander, electro-decontamination...) but for some of them, the efficiency is limited (e.g, Dry Ice blasting) and for others, the wastes production (liquid and/or solid) remains an important issue. One answer could be the use of a LASER light process. Since a couple of years, the Clean- Up Business Unit of the AREVA group investigates this decontamination technology. Many tests have been already performed in inactive (i.e. on simulants such as paints, inks, resins, metallic oxides) or active conditions (i.e. pieces covered with a thick metallic oxide layer and metallic pieces covered with grease). The paper will describe the results obtained in term of decontamination efficiency during all our validation process. Metallographic characterizations (i.e. SEM, X-ray scattering) and radiological analysis will be provided. We will also focus our paper on the future deployment of the LASER technology and its commercial use at La Hague reprocessing facility in 2013. (authors)

  10. Biodegradation of concrete intended for their decontamination; Biodegradation de matrices cimentaires en vue de leur decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Jestin, A

    2005-05-15

    The decontamination of sub-structural materials represents a stake of high importance because of the high volume generated. It is agreed then to propose efficient and effective processes. The process of bio-decontamination of the hydraulic binders leans on the mechanisms of biodegradation of concretes, phenomenon characterized in the 40's by an indirect attack of the material by acids stem from the microbial metabolism: sulphuric acid (produced by Thiobacillus), nitric acid (produced by Nitrosomonas and Nitrobacter) and organic acids (produced by fungi). The principle of the bio-decontamination process is to apply those microorganisms on the surface of the contaminated material, in order to damage its surface and to retrieve the radionuclides. One of the multiple approaches of the process is the use of a bio-gel that makes possible the micro-organisms application. (author)

  11. Decontamination techniques of pathogen bacteria in meat and poultry.

    Science.gov (United States)

    Dinçer, A Handan; Baysal, Taner

    2004-01-01

    Means of controlling or even improving the safety of food products is to decontaminate the carcasses or products during or at the end of the production line. The decontamination of meat and poultry can help to reduce human foodborne infections. However, process hygiene to prevent contamination should never be neglected. Some techniques of decontaminating raw meat and poultry meat products are discussed in this review.

  12. Decontamination and dismantlement of Plant 7 at Fernald

    Energy Technology Data Exchange (ETDEWEB)

    Albertin, M.; Borgman, T.; Zebick, B.

    1994-11-07

    Decontamination and dismantlement (D&D) tasks have been successfully completed on Plant 7 at the Fernald Environmental Management Project. The seven story facility was radiologically, chemically, and biologically contaminated. The work involved the D&D work beginning with safe shutdown and gross decontamination, and ended with removal of the structural steel. A series of lessons learned were gained which include use of explosives, bidding tactics, safe shutdown, building decontamination and lockdown, use of seam climbers, etc.

  13. New decontamination process using foams containing particles

    Energy Technology Data Exchange (ETDEWEB)

    Guignot, S.; Faure, S. [CEA Marcoule, Lab. des Procedes Avances de Decontamination, 30 (France)

    2008-07-01

    One key point in the dismantling of nuclear facilities is the thorough cleaning of radiation- exposed surfaces on which radioactive deposits have formed. This cleaning step is often achieved by successive liquid rinses with specific solutions containing alkaline, acidic, or even oxidizing species depending on whether the aim is to dissolve greasy deposits (like ter-butylphosphate) or to corrode surfaces on micrometric thicknesses. An alternative process to reduce the amount of chemicals and the volume of the resulting nuclear wastes consists in using the same but foamed solutions (1). Carrying less liquid, the resulting foams still display similar kinetics of dissolution rates and their efficiency is determined by their ability to hold sufficient wetnesses during the time required for the decontamination. Classical foam decontamination process illustrated by foam pulverization or circulation in the 90 turned five years ago into a specific static process using high-lifetime viscosified foam at a steady state. One way to slow down the liquid drainage is to raise liquid viscosity by adding organic viscosifiers like xanthan gum (2). In 2005, new studies started on an innovative process proposed by S. Faure and based on triphasic foams containing particles [3]. The aim is to generate new decontamination foams containing less quantities of organics materials (surfactants and viscosifiers). Silica particles are obviously known to stabilize or destabilize foams (4). In the frame of S. Guignot Ph.D., new fundamental studies are initiated in order to clarify the role of silica solid microparticles in these foams. Our final goal is to determine whether this kind of new foam can be stable for several hours for a decontamination process. The results we will report focus on wet foams used for nuclear decontamination and incorporating fumed silica. The study is conducted on a vertical foam column in a pseudo-free drainage configuration, and aims at investigating the influence of

  14. Personal protective equipment and decontamination of adults and children.

    Science.gov (United States)

    Holland, Michael G; Cawthon, David

    2015-02-01

    Accurate identification of the hazardous material is essential for proper care. Efficient hospital security and triage must prevent contaminated victims from entering the emergency department (ED) and causing secondary contamination. The decontamination area should be located outside the ambulance entrance. Decontamination priorities are protection of the health care worker, utilization of Level C personal protective equipment, and proper decontamination of the exposed patient. Decontamination proceeds in a head-to-toe sequence. Run-off water is a hazardous waste. Hospital and Community Management Planning for these emergencies is essential for proper preparation and effective response to the hazardous materials incident.

  15. 40 CFR 761.79 - Decontamination standards and procedures.

    Science.gov (United States)

    2010-07-01

    ... separation, spraying, soaking, wiping, stripping of insulation, scraping, scarification or the use of... separated from regulated waste during decontamination (such as by chopping, shredding, scraping, abrading...

  16. Portable Multiplex Pathogen Detector

    Energy Technology Data Exchange (ETDEWEB)

    Visuri, S; McBride, M T; Matthews, D; Rao, R

    2002-07-15

    Tumor marker concentrations in serum provide useful information regarding clinical stage and prognosis of cancer and can thus be used for presymptomatic diagnostic purposes. Currently, detection and identification of soluble analytes in biological fluids is conducted by methods including bioassays, ELISA, PCR, DNA chip or strip tests. While these technologies are generally sensitive and specific, they are time consuming, labor intensive and cannot be multiplexed. Our goal is to develop a simple, point-of-care, portable, liquid array-based immunoassay device capable of simultaneous detection of a variety of cancer markers. Here we describe the development of assays for the detection of Serum Prostate Specific Antigen, and Ovalbumin from a single sample. The multiplexed immunoassays utilize polystyrene microbeads. The beads are imbedded with precise ratios of red and orange fluorescent dyes yielding an array of 100 beads, each with a unique spectral address (Figure 1). Each bead can be coated with capture antibodies specific for a given antigen. After antigen capture, secondary antibodies sandwich the bound antigen and are indirectly labeled by the fluorescent reporter phycoerythrin (PE). Each optically encoded and fluorescently-labeled microbead is then individually interrogated. A red laser excites the dye molecules imbedded inside the bead and classifies the bead to its unique bead set, and a green laser quantifies the assay at the bead surface. This technology has been proven to be comparable to the ELISA in terms of sensitivity and specificity. We also describe the laser-based instrumentation used to acquire fluorescent bead images Following the assay, droplets of bead suspension containing a mixture of bead classes were deposited onto filters held in place by a disposable plexiglass device and the resultant arrays viewed under the fluorescent imaging setup. Using the appropriate filter sets to extract the necessary red, orange and green fluorescence from the

  17. Development of Decontamination Chest Set with Electrolyzed Oxidizing Water%氧化电位水洗消箱组的研制

    Institute of Scientific and Technical Information of China (English)

    夏本立; 陈志林; 王力

    2011-01-01

    Objective To develop a decontamination chest set with electrolyzed oxidizing water. Methods with the advantages such as non -toxic, innocuity and reproducible, was a new -style and green bactericide. The EOW decontamination technology was apllied in the mobile platform, according to the theories of miniaturization, modularization and functionality. The decontamination chest set with EOW was composed of EOW decontamination chest and individual portable EOW decontamination shelter, of which, the former had non-metal-polymers trunk and totally enclosed structure, and the latter used teflon materials and closed structure. Results The decontamination chest set, being mobile, anti-shock, anti-high-temperature, cold-resistant and damp-proofing, could be used for mobile or field decontamination at wartime and peacetime. Conclusion The decontamination chest set with electrolyzed oxidizing water, with the simple structure and being easy to operate, enhances the decontamination ability of the troops.[Chinese Medical Equipment Journal,2011,32 (12):40-41,55]%目的:研制氧化电位水洗消箱组,以提升军队卫勤装备的保障能力.方法:氧化电位水洗消箱组将氧化电位水洗消技术搭载到移动平台,整个箱组由氧化电位水洗消箱和氧化电位水单兵便携洗消仓组成.其中氧化电位水洗消箱为非金属高分子复合材料箱仓式全封闭结构:氧化电位水单兵便携洗消仓为聚四氟乙烯密闭结构.结果:该装备操作简便,具有“可移动、防震、防高温、防寒、防潮排湿”的特点,在野战条件下、自然灾害发生时能机动至现场进行消毒洗消.结论:该氧化电位水消毒箱组操作简单快捷,提高了部队的洗消能力.

  18. Polluted soils. Electro-kinetic decontamination seems promising; Sols pollues. Les promesses de la decontamination electrocinetique

    Energy Technology Data Exchange (ETDEWEB)

    Tellier, S.; Astruc, M. [Pau Univ., Lab. de Chimie Analytique Bio-Inorganique et Environnement, UMR 5034 64 (France)

    2000-10-01

    The electro-kinetic treatment of polluted soils is a recent technique. It is particularly well adapted to the decontamination of low permeable media or of difficult species (metals, arsenic, polycyclic aromatic hydrocarbons..). Conditions where classical methods are often inefficient. (O.M.)

  19. Full system decontamination experience in BWR

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, N.; Sugai, K.; Katayouse, N.; Fujimori, A.; Iida, K.; Hayashi, K. [Tokyo Electric Power Company, Tokyo (Japan); Kanasaki, T.; Inami, I. [Toshiba Corporation, Yokohama (Japan); Strohmer, F. [Framatome ANP Gmbh, Eelangen (Germany)

    2002-07-01

    At the Fukushima Daiichi Nuclear Power Station unit 3, unit 2, unit 5 and unit 1 of Tokyo Electric Power Company (TEPCO), the replacement of the core shroud and internals has been conducted since 1997 in this order. The welded core internals in operating BWR plants were replaced to improve stress corrosion cracking (SCC) resistance. At present these units are operating smoothly. The developed technology concept is to restore those internals in open air inside the reactor pressure vessel (RPV). To reduce the radiation dose rate inside the RPV, not only a shielding method was applied to cut the radiation from the irradiated structures but also a chemical decontamination method was applied to dissolve the radioactive crud deposited on the surface by using chemical agents. The calculated decontamination factor (DF) at the RPV bottom reached 35-117. As result, the dose rate decreased to approximately 0.1 mSv/h under water. Before and after the installation of the in-vessel shielding, a mechanical cleaning was extensively applied inside the RPV to remove the residual crud as well as the swarf, chips from cutting. As a result, the dose rate at the RPV bottom decreased to ranging from 0.2 to 0.4 mSv/h in air. A working environment for human access, which was better than expected, was established inside the RPV, resulting in 70, 140, 50 and 70 man-Sv (estimated) saving respectively at unit 3 (1F-3), unit 2(1F-2), unit 5(1F-5) and unit 1(1F-1). All four full system decontamination (FSDs) contributed to the successful realization of the core shroud replacement project under the dry condition in RPV.

  20. Contactless decontamination of hair samples: cannabinoids.

    Science.gov (United States)

    Restolho, José; Barroso, Mário; Saramago, Benilde; Dias, Mário; Afonso, Carlos A M

    2017-02-01

    Room temperature ionic liquids (ILs) have already been shown to provide efficient extraction media for several systems, and to capture volatile compounds, namely opiates. In this work, a novel, contactless, artefact-free extraction procedure for the removal of Δ(9) -tetrahrydrocannabinol (THC) from the surface of human hair is presented. To prepare in vitro cannabinoids-contaminated hair, samples were flushed with hashish smoke for 7 h. The decontamination experiments were carried at 100 °C for 24 h, according to the procedure previously described. Fifty-three ILs were screened and presented decontamination efficiencies ranging from 0 to 96 %. Although the majority of the ILs presented efficiencies above 90%, the 1-ethanol-3-methyl tetrafluoroborate (96%) was chosen for further process optimization. The Design of Experiments results demonstrated that all studied variables were significant for the process and the obtained optimum conditions were: 100 °C, 13 h and 175 mg of IL. In the work of Perrotin-Brunel et al. (J. Mol. Struct. 2011, 987, 67), it is demonstrated that, at 100 °C, full conversion of tetrahydrocannabinolic acid (THCA) into THC is obtained after 60 min. Since our decontamination takes place over 13 h at 100 °C, full conversion of THCA into THC is expected. Additionally, our method was compared with the method proposed by Cairns et al. (Forensic Sci. Int. 2004, 145, 97), through the analysis of 15 in vitro contaminated hair samples. The results demonstrated that with our method a mean extraction efficiency of 11 % higher was obtained. Copyright © 2016 John Wiley & Sons, Ltd.

  1. [Portable instrument for arteriosclerosis assessment].

    Science.gov (United States)

    Cao, Shuai; Chen, Xiang

    2014-01-01

    A portable instrument for arteriosclerosis assessment containing sensor module, acquisition board and embedded module was developed for home care in this paper. The sensor module consists of one ECG module and three pulse wave extraction modules, synchronously acquiring human ECG and pulse wave signal of carotid, radial, and dorsal, respectively. The acquisition board converts the sensor module's analog output signals into digital signals and transmits them to the embedded module. The embedded module realizes the functions including signal display, storage and the calculation and output of pulse wave velocity. The structure of the proposed portable instrument is simple, easy to use, and easy to expand. Small size, low cost, and low power consumption are also the advantages of this device. Experimental results demonstrated that the proposed portable instrument for arteriosclerosis assessment has high accuracy, good repeatability and can assess the degree of atherosclerosis appropriately.

  2. MacBook portable genius

    CERN Document Server

    Miser, Brad

    2008-01-01

    The Genius is in. You don't have to be a genius to use a MacBook. But if you want to get the very most out of yours, put this savvy Portable Genius guide to work. Want to connect your MacBook to other Macs? Use Expose to its fullest potential? Troubleshoot? You'll find cool and useful Genius tips, insider secrets, full-color screenshots, and pages of easy-to-access shortcuts and tools that will save you loads of time and make your MacBook IQ soar. Portable GENIUS Fun, hip, and straightforward, the new Portable Genius series gives forward-thinking Apple users useful informat

  3. Development of decontamination, decommissioning and environmental restoration technology

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Byung Jik; Kwon, H. S.; Kim, G. N. and others

    1999-03-01

    Through the project of 'Development of decontamination, decommissioning and environmental restoration technology', the followings were studied. 1. Development of decontamination and repair technology for nuclear fuel cycle facilities 2. Development of dismantling technology 3. Development of environmental restoration technology. (author)

  4. Reactivity of Dual-Use Decontaminants with Chemical Warfare Agents

    Science.gov (United States)

    2016-07-01

    decrease the logistical burden associated with transport and storage of decontaminants. The experiments in this study were focused on evaluating...propanediammonium dichloride, isopropanol, inert ingredients/water, hydrogen peroxide, diacetin Decontaminant formulated for chemical warfare agents F...potassium bisulfate, potassium sulfate, dipotassium peroxodisulfate, magnesium carbonate Acidic oxidative chemistry, used for VX laboratory waste

  5. Stability of Decontamination Foam Containing Silica Nanoparticles and Viscosifier

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, In Ho; Jung, Chong Hun; Yoon, Suk Bon; Kim, Chorong; Jung, Jun Young; Park, Sang Yoon; Moon, Jei Kwon; Choi, Wang Kyu [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2013-10-15

    This formulation can significantly decrease the amounts of chemical reagents and secondary waste. The advantage of decontamination foam is its potentially wide application for metallic walls, overhead surfaces, and the elements of complex components and facilities. In addition, foam is a good material for in situ decontamination because it generates low final waste volumes owing to its volume expansion. The application of foam allows for remote decontamination processing using only an injection nozzle and the equipment to generate the decontamination foam, which reduces operator exposure to high radioactivity. The decontamination efficiency can be enhanced by improving the contact time between chemical reagents and a contaminated surface through the addition of surfactants and viscosifiers into the decontamination foam. The objective of this study is to investigate the effect of silica nanoparticles and a viscosifier on the foam stability and the dissolution behaviors of corroded specimens using a non-ionic surfactant. This study showed the effect of viscosifiers and nanoparticles on the foam stability when developing new formulations of decontamination foam. The addition of xanthan gum and the mixture of xanthan gum and silica nanoparticles (M-5) significantly increased the foam stability, compared to the surfactant solution alone. This result indicates that both the viscosifier and nanoparticles have a synergistic effect on the foam stability. As the contact time increased, the dissolution rate increased to become similar to the dissolution that contained decontamination liquid.

  6. 41 CFR 101-45.001 - Demilitarization and decontamination.

    Science.gov (United States)

    2010-07-01

    ... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Demilitarization and..., ABANDONMENT, OR DESTRUCTION OF PERSONAL PROPERTY § 101-45.001 Demilitarization and decontamination. (a... characteristics, or otherwise making it unfit for further use. (b) Demilitarization or decontamination of...

  7. The effects of selective decontamination in Dutch Intensive Care Units

    NARCIS (Netherlands)

    Oostdijk, E.A.N.

    2013-01-01

    Infections are an important complication in the treatment of critical ill patients in Intensive Care Units (ICUs) and are associated with increased mortality, morbidity and health care costs. Selective Decontamination of the Digestive Tract (SDD) and Selective Oropharyngeal Decontamination (SOD) are

  8. Decontamination, decommissioning, and vendor advertorial issue, 2006

    Energy Technology Data Exchange (ETDEWEB)

    Agnihotri, Newal (ed.)

    2006-07-15

    The focus of the July-August issue is on Decontamination, decommissioning, and vendor advertorials. Major articles/reports in this issue include: NPP Krsko revised decommissioning program, by Vladimir Lokner and Ivica Levanat, APO d.o.o., Croatia, and Nadja Zeleznik and Irena Mele, ARAO, Slovenia; Supporting the renaissance, by Marilyn C. Kray, Exelon Nuclear; Outage world an engineer's delight, by Tom Chrisopher, Areva, NP Inc.; Optimizing refueling outages with R and D, by Ross Marcoot, GE Energy; and, A successful project, by Jim Lash, FirstEnergy.

  9. Automated Single Cell Data Decontamination Pipeline

    Energy Technology Data Exchange (ETDEWEB)

    Tennessen, Kristin [Lawrence Berkeley National Lab. (LBNL), Walnut Creek, CA (United States). Dept. of Energy Joint Genome Inst.; Pati, Amrita [Lawrence Berkeley National Lab. (LBNL), Walnut Creek, CA (United States). Dept. of Energy Joint Genome Inst.

    2014-03-21

    Recent technological advancements in single-cell genomics have encouraged the classification and functional assessment of microorganisms from a wide span of the biospheres phylogeny.1,2 Environmental processes of interest to the DOE, such as bioremediation and carbon cycling, can be elucidated through the genomic lens of these unculturable microbes. However, contamination can occur at various stages of the single-cell sequencing process. Contaminated data can lead to wasted time and effort on meaningless analyses, inaccurate or erroneous conclusions, and pollution of public databases. A fully automated decontamination tool is necessary to prevent these instances and increase the throughput of the single-cell sequencing process

  10. Microwave-Based Water Decontamination System

    Science.gov (United States)

    Arndt, G. Dickey (Inventor); Byerly, Diane (Inventor); Sognier, Marguerite (Inventor); Dusl, John (Inventor)

    2016-01-01

    A system for decontaminating a medium. The system can include a medium having one or more contaminants disposed therein. The contaminants can be or include bacteria, fungi, parasites, viruses, and combinations thereof. A microwave energy radiation device can be positioned proximate the medium. The microwave energy radiation device can be adapted to generate a signal having a frequency from about 10 GHz to about 100 GHz. The signal can be adapted to kill one or more of the contaminants disposed within the medium while increasing a temperature of the medium by less than about 10 C.

  11. Development and field testing of a mobile chlorine dioxide generation system for the decontamination of buildings contaminated with Bacillus anthracis

    Energy Technology Data Exchange (ETDEWEB)

    Wood, Joseph P., E-mail: wood.joe@epa.gov [U.S. Environmental Protection Agency, Office of Research and Development, National Homeland Security Research Center, MC-E343-06, Research Triangle Park, NC 27711 (United States); Blair Martin, G., E-mail: martin.blair@epa.gov [U.S. Environmental Protection Agency, Office of Research and Development, National Risk Management Research Laboratory, MC-E340-C, Research Triangle Park, NC 27711 (United States)

    2009-05-30

    The numerous buildings that became contaminated with Bacillus anthracis (the bacterium causing the disease anthrax) in 2001, and more recent B. anthracis - related events, point to the need to have effective decontamination technologies for buildings contaminated with biological threat agents. The U.S. Government developed a portable chlorine dioxide (ClO{sub 2}) generation system to decontaminate buildings contaminated with B. anthracis spores, and this so-called mobile decontamination trailer (MDT) prototype was tested through a series of three field trials. The first test of the MDT was conducted at Fort McClellan in Anniston, AL. during October 2004. Four test attempts occurred over two weekends; however, a number of system problems resulted in termination of the activity prior to any ClO{sub 2} introduction into the test building. After making several design enhancements and equipment changes, the MDT was subjected to a second test. During this test, extensive leak checks were made using argon and nitrogen in lieu of chlorine gas; each subsystem was checked for functionality, and the MDT was operated for 24 h. This second test demonstrated the MDT flow and control systems functioned satisfactorily, and thus it was decided to proceed to a third, more challenging field trial. In the last field test, ClO{sub 2} was generated and routed directly to the scrubber in a 12-h continuous run. Measurement of ClO{sub 2} levels at the generator outlet showed that the desired production rate was not achieved. Additionally, only one of the two scrubbers performed adequately with regard to maintaining ClO{sub 2} emissions below the limit. Numerous lessons were learned in the field trials of this ClO{sub 2} decontamination technology.

  12. A Portable Passive Physiotherapeutic Exoskeleton

    Directory of Open Access Journals (Sweden)

    Dasheek Naidu

    2012-10-01

    A physiotherapeutic mechanism was designed to be portable and adjustable, without limiting the spherical motion and workspace of the human arm. The exoskeleton was designed to be portable in the sense that it could be transported geographically. It is a complete device allowing for motion in the shoulder, elbow, wrist and hand joints. The inverse kinematics was solved iteratively via the Damped Least Squares (DLS method. The electronic and computer system allowed for professional personnel to either change an individual joint or a combination of joints angles via the kinematic models. A ramp PI controller was established to provide a smooth response to simulate the passive therapy motion.

  13. Portable Heat Pump Testing Device

    Directory of Open Access Journals (Sweden)

    Kłosowiak R.

    2015-08-01

    Full Text Available The aim of this paper is to present the design and working principle of a portable testing device for heat pumps in the energy recirculation system. The presented test stand can be used for any refrigerating/reverse flow cycle device to calculate the device energy balance. The equipment is made of two portable containers of the capacity of 250 liters to simulate the air heat source and ground heat source with a system of temperature stabilization, compressor heat pump of the coefficient of performance (COP of = 4.3, a failsafe system and a control and measurement system.

  14. Evaluation of five decontamination methods for filtering facepiece respirators.

    Science.gov (United States)

    Viscusi, Dennis J; Bergman, Michael S; Eimer, Benjamin C; Shaffer, Ronald E

    2009-11-01

    Concerns have been raised regarding the availability of National Institute for Occupational Safety and Health (NIOSH)-certified N95 filtering facepiece respirators (FFRs) during an influenza pandemic. One possible strategy to mitigate a respirator shortage is to reuse FFRs following a biological decontamination process to render infectious material on the FFR inactive. However, little data exist on the effects of decontamination methods on respirator integrity and performance. This study evaluated five decontamination methods [ultraviolet germicidal irradiation (UVGI), ethylene oxide, vaporized hydrogen peroxide (VHP), microwave oven irradiation, and bleach] using nine models of NIOSH-certified respirators (three models each of N95 FFRs, surgical N95 respirators, and P100 FFRs) to determine which methods should be considered for future research studies. Following treatment by each decontamination method, the FFRs were evaluated for changes in physical appearance, odor, and laboratory performance (filter aerosol penetration and filter airflow resistance). Additional experiments (dry heat laboratory oven exposures, off-gassing, and FFR hydrophobicity) were subsequently conducted to better understand material properties and possible health risks to the respirator user following decontamination. However, this study did not assess the efficiency of the decontamination methods to inactivate viable microorganisms. Microwave oven irradiation melted samples from two FFR models. The remainder of the FFR samples that had been decontaminated had expected levels of filter aerosol penetration and filter airflow resistance. The scent of bleach remained noticeable following overnight drying and low levels of chlorine gas were found to off-gas from bleach-decontaminated FFRs when rehydrated with deionized water. UVGI, ethylene oxide (EtO), and VHP were found to be the most promising decontamination methods; however, concerns remain about the throughput capabilities for EtO and VHP

  15. Selective decontamination of the digestive tract and selective oropharyngeal decontamination in intensive care unit patients : a cost-effectiveness analysis

    NARCIS (Netherlands)

    Oostdijk, Evelien A. N.; de Wit, G. A.; Bakker, Marina; de Smet, Anne-Marie; Bonten, M. J. M.

    2013-01-01

    Objective: To determine costs and effects of selective digestive tract decontamination (SDD) and selective oropharyngeal decontamination (SOD) as compared with standard care (ie, no SDD/SOD (SC)) from a healthcare perspective in Dutch Intensive Care Units (ICUs). Design: A post hoc analysis of a pre

  16. Project n.4: local strategies for decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Hubert, Ph. [CEA Centre d`Etudes de Fontenay-aux-Roses, 92 (France). Inst. de Protection et de Surete Nucleaire; Ramzaev, V. [Branch of Institute of Radiation Hygiene, Karchovka, Bryandk (Russian Federation); Antsypov, G. [Chernobyl State Committee of the Republic of Belarus, (Belarus); Sobotovich, E. [Institute of Geochemistry, Mineralogy and Ore formation, Kiev (Ukraine); Anisimova, L. [EMERCOM, Moscow (Russian Federation)

    1995-12-31

    The efficiencies of a great number of techniques for decontamination or dose reduction in contaminated areas have been investigated by several teams of E.C. and CIS scientists (ECP4 project). Modelling, laboratory and field experiments, and a return from experience from the area contaminated by the Chernobyl accident allowed to assess radiological efficiencies and requirements for the operation of numerous practical solutions. Then those data were supplemented with data on cost and waste generation in order to elaborate all the information for the optimisation of decontamination strategies. Results are presented for about 70 techniques. However, a technique cannot be compared to another from a generic point of view. Rather it is designed for a specific target and the best technology depends on the objectives. It has been decided to implement decision analyses on case studies and the local conditions and objectives have been investigated. Individual doses ranged from 1 to 5 mSv, with the contrasted contributions of internal and external doses. The desire to restore a normal activity in a partially depopulated settlement and concerns about the recent increase in internal doses were typical incentives for action. The decision aiding analysis illustrated that actions can be usually recommended. Results are outlined. (authors). 23 refs.

  17. Progress in portable direct methanol fuel cell

    Institute of Scientific and Technical Information of China (English)

    佘沛亮; 胡信国; 陈怀林

    2004-01-01

    The progresses in portable DMFC worldwide were reviewed, the current status of its components, catalysts, proton exchange membrane and flow field plate, the market development of portable electronic appliances, such as mobile phone, PDA and notebook were introduced.

  18. The Evolution of Educational Software Portability.

    Science.gov (United States)

    Collis, Betty

    1996-01-01

    Discusses issues related to the portability, or transferability, of educational software. Topics include motivations for portability, including economic and social; technology transfer experiences; technical, educational, social/cultural, and organizational factors; examples, including international projects; handling multiple languages; graphical…

  19. Portable File Format (PFF) specifications

    Energy Technology Data Exchange (ETDEWEB)

    Dolan, Daniel H. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-02-01

    Created at Sandia National Laboratories, the Portable File Format (PFF) allows binary data transfer across computer platforms. Although this capability is supported by many other formats, PFF files are still in use at Sandia, particularly in pulsed power research. This report provides detailed PFF specifications for accessing data without relying on legacy code.

  20. Portable Pallet-Weighing Apparatus

    Science.gov (United States)

    Day, R. M.

    1983-01-01

    Portable apparatus intended for standard four-trunnion pallets readily adaptable to any large payload or other loads where shifting of cargo is to be avoided. Device lifts trunnion of pallet short distance above its resting place. Weight at trunnion applied to load cell. Similar units placed at all four trunnions.

  1. 49 CFR 172.326 - Portable tanks.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Portable tanks. 172.326 Section 172.326... SECURITY PLANS Marking § 172.326 Portable tanks. (a) Shipping name. No person may offer for transportation or transport a portable tank containing a hazardous material unless it is legibly marked on...

  2. Long-term decontamination engineering study. Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Geuther, W.J.

    1995-04-03

    This report was prepared by Westinghouse Hanford Company (WHC) with technical and cost estimating support from Pacific Northwest Laboratories (PNL) and Parsons Environmental Services, Inc. (Parsons). This engineering study evaluates the requirements and alternatives for decontamination/treatment of contaminated equipment at the Hanford Site. The purpose of this study is to determine the decontamination/treatment strategy that best supports the Hanford Site environmental restoration mission. It describes the potential waste streams requiring treatment or decontamination, develops the alternatives under consideration establishes the criteria for comparison, evaluates the alternatives, and draws conclusions (i.e., the optimum strategy for decontamination). Although two primary alternatives are discussed, this study does identify other alternatives that may warrant additional study. hanford Site solid waste management program activities include storage, special processing, decontamination/treatment, and disposal facilities. This study focuses on the decontamination/treatment processes (e.g., waste decontamination, size reduction, immobilization, and packaging) that support the environmental restoration mission at the Hanford Site.

  3. Planning guidance for nuclear-power-plant decontamination. [PWR; BWR

    Energy Technology Data Exchange (ETDEWEB)

    Munson, L.F.; Divine, J.R.; Martin, J.B.

    1983-06-01

    Direct and indirect costs of decontamination are considered in the benefit-cost analysis. A generic form of the benefit-cost ratio is evaluated in monetary and nonmonetary terms, and values of dollar per man-rem are cited. Federal and state agencies that may have jurisiction over various aspects of decontamination and waste disposal activities are identified. Methods of decontamination, their general effectiveness, and the advantages and disadvantages of each are outlined. Dilute or concentrated chemical solutions are usually used in-situ to dissolve the contamination layer and a thin layer of the underlying substrate. Electrochemical techniques are generally limited to components but show high decontamination effectiveness with uniform corrosion. Mechanical agents are particularly appropriate for certain out-of-system surfaces and disassembled parts. These processes are catagorized and specific concerns are discussed. The treatment, storage, and disposal or discharge or discharge of liquid, gaseous, and solid wastes generated during the decontamination process are discussed. Radioactive and other hazardous chemical wastes are considered. The monitoring, treatment, and control of radioactive and nonradioactive effluents, from both routine operations and possible accidents, are discussed. Protecting the health and safety of personnel onsite during decontamination is of prime importance and should be considered in each facet of the decontamination process. The radiation protection philosophy of reducing exposure to levels as low as reasonably achievable should be stressed. These issues are discussed.

  4. Gaseous decontamination for major cp, fp and tru

    Energy Technology Data Exchange (ETDEWEB)

    Tatenuma, K.; Hishinuma, T.; Isoyama, N.; Noguchi, T. [Kaken Co. Mito-Institute, Ibaraki (Japan); Suzuki, M. [Tokyo Institute of Technology, Tokyo (Japan)

    1999-07-01

    As an effective decontamination based on dry-base treatment, we have developed two types practical gaseous decontamination technologies, one is based on carbonylation and fluorination reactions using several types of chemically reactive plasmas which have the performances and high efficiencies to decontaminate simultaneously the contaminants of major CP, FP and TRU, and another is based on fluorination reaction using fluoric reagent (i e., ClF{sub 3}, BrF{sub 5}, IF{sub 7}, etc.) to decontaminate the contaminants of major F P and TRU. In this study, it was verified that all of the chemically reactive plasmas of five types, which are electron cyclotron resonance, direct current, radio frequency, down stream micro wave and corona discharge, have high decontamination efficiencies of {sup 60}Co and uranium, and on the other hand the result of highly reactive gas decontamination using ClF{sub 3} as fluoric reagent showed that the contaminants of UF{sub 6} centrifugal concentrator were mostly cleaned up to non-radioactive materials under the treatment conditions of ambient temperature, short time and reduced pressure. The developed gas-phase decontamination technology based on volumes of waste created each year or non-incinerable radioactive waste. (author)

  5. Benefits of automated surface decontamination of a radioiodine ward.

    Science.gov (United States)

    Westcott, Eliza; Broadhurst, Alicia; Crossley, Steven; Lee, Lloyd; Phan, Xuyen; Scharli, Rainer; Xu, Yan

    2012-02-01

    A floor-washing robot has been acquired to assist physicists with decontamination of radioiodine therapy ward rooms after discharge of the patient at Sir Charles Gairdner Hospital. The effectiveness of the robot in decontaminating the ward has been evaluated. A controlled experiment was performed by deliberately contaminating a polyvinyl chloride flooring offcut with 131I followed by automated decontamination with the robot. The extent of fixed and removable contamination was assessed before and after decontamination by two methods: (1) direct Geiger-Mueller counting and (2) beta-counting wipe tests. Surface contamination was also assessed in situ on the ward by Geiger-Mueller counting and wipe testing. Contamination maps confirmed that contamination was removed rather than spread around by the robot. Wipe testing revealed that the robot was successful in clearing approximately 60-80% of removable contamination. The robotic floor-washing device was considered suitable to provide effective automated decontamination of the radioiodine ward. In addition, the robot affords other benefits: the time spent by the physicists decontaminating the room is greatly reduced offering financial and occupational safety and health benefits. The robot has also found utility in other decontamination applications in the healthcare environment.

  6. Comparative analysis of showering protocols for mass-casualty decontamination.

    Science.gov (United States)

    Amlot, Richard; Larner, Joanne; Matar, Hazem; Jones, David R; Carter, Holly; Turner, Elizabeth A; Price, Shirley C; Chilcott, Robert P

    2010-01-01

    A well-established provision for mass-casualty decontamination that incorporates the use of mobile showering units has been developed in the UK. The effectiveness of such decontamination procedures will be critical in minimizing or preventing the contamination of emergency responders and hospital infrastructure. The purpose of this study was to evaluate three empirical strategies designed to optimize existing decontamination procedures: (1) instructions in the form of a pictorial aid prior to decontamination; (2) provision of a washcloth within the showering facility; and (3) an extended showering period. The study was a three-factor, between-participants (or "independent") design with 90 volunteers. The three factors each had two levels: use of washcloths (washcloth/no washcloth), washing instructions (instructions/no instructions), and shower cycle duration (three minutes/six minutes). The effectiveness of these strategies was quantified by whole-body fluorescence imaging following application of a red fluorophore to multiple, discrete areas of the skin. All five showering procedures were relatively effective in removing the fluorophore "contaminant", but the use of a cloth (in the absence of instructions) led to a significant ( appox. 20%) improvement in the effectiveness of decontamination over the standard protocol (p mass-casualty decontamination effectiveness, especially in children, can be optimized by the provision of a washcloth. This simple but effective approach indicates the value of performing controlled volunteer trials for optimizing existing decontamination procedures.

  7. Nuclear disaster. Fukushima, hundred years of decontamination; Catastrophe nucleaire: Fukushima, cent ans de decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Dupin, L.

    2011-04-15

    This article gives an overview of what will have to be done on the site of Fukushima to decontaminate and to dismantle it. Based on the experience gained in Three Mile Island and in Chernobyl, experts foresee ten years of work within the reactor cores, thirty years around the plant, sixty years of decontamination within the no man's land area around the plant; and centuries as far as scattered spots are concerned more than hundred kilometres away from the plant. Three radionuclides must be surveyed, but with different half lives: iodine 131 (8 days), caesium 137 (30 years), and plutonium 239 (24000 years). The expertise of French companies (Areva, Assystem, Bouygues and Vinci) in reactor dismantling, dismantling procedure design, and public works (protection arch like in Chernobyl) is briefly evoked, as well as the French approach for post-accident management

  8. Showering effectiveness for human hair decontamination of the nerve agent VX.

    Science.gov (United States)

    Josse, Denis; Wartelle, Julien; Cruz, Catherine

    2015-05-05

    In this work, our goals were to establish whether hair decontamination by showering one hour post-exposure to the highly toxic organophosphate nerve agent VX was effective, whether it required the addition of a detergent to water and, if it could be improved by using the adsorbent Fuller's Earth (FE) or the Reactive Skin Decontamination Lotion (RSDL) 30 min prior to showering. Hair exposure to VX and decontamination was performed by using an in vitro model. Hair showering led to 72% reduction of contamination. Addition of detergent to water slightly increased the decontamination effectiveness. Hair treatment with FE or RSDL improved the decontamination rate. Combination of FE use and showering, which yielded a decontamination factor of 41, was demonstrated to be the most effective hair decontamination procedure. Hair wiping after showering was shown to contribute to hair decontamination. Altogether, our results highlighted the importance of considering hair decontamination as an important part of body surface decontamination protocols.

  9. Skin decontamination of G, V, H L agents by Canadian reactive skin decontaminant lotion

    Energy Technology Data Exchange (ETDEWEB)

    Bide, R.W.; Sawyer, T.W.; DiNinno, V.L.; Armour, S.J.; Risk, D.J.

    1993-05-13

    The Canadian Reactive Skin Decontaminant Lotion (RSDL) is a reactive solution designed to be applied directly to skin for the decontamination and destruction of the classical chemical warfare agents. The solvent of the RSDL is very effective in dissolving liquid agents from the skin surface and the differential solubility of agents in the RSDL and the skin strongly favors retention of agents in the lotion. The active ingredient in the RSDL reacts rapidly and completely with G-agents, V-agents, mustard Lewisite producing relatively nontoxic products. The RSDL will dissolve and destroy agent thickened with acrylate polymers. The lotion is water soluble and readily removed from the skin. Since the RSDL is water soluble, it is active against water soluble agents even at high dilutions. For water insoluble agents, the activity is reduced as the water content rises above abrasive 50% due to insolubility of the agents. Skin and eye irritancy trials indicate that the RSDL is only a mild irritant to the eyes (equivalent to a chlorinated swimming pool) and to abraded skin. Acute toxicity trials showed that large oral and intraperitoneal doses were essentially non-toxic. The RSDL was fielded by the Canadian Forces for the Gulf Conflict. The RSDL may be used in open wounds for short periods. Wound decontamination and irrigation with RSDL diluted 1:1 with isotonic saline was recommended for the Gulf conflict.

  10. Laser Decontamination of Surfaces Contaminated with Cs+ Ion

    Energy Technology Data Exchange (ETDEWEB)

    Baigalmaaa, B.; Won, H. J.; Moon, J. K.; Jung, C. H.; Lee, K. W. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Hyun, J. H. [Chungnam National University, Daejon (Korea, Republic of)

    2008-10-15

    Laser decontamination technology has been proven to be an efficient method for a surface modification of metals and concretes contaminated with radioactive isotopes. Furthermore, the generation of a secondary waste is negligible. The radioactivity of hot cells in the DFDF (Dupic Fuel Development Facility) is presumed to be very high and the predominant radionuclide is Cs-137. A series of laser decontamination studies by a fabricated Q-switched Nd:YAG laser system were performed on stainless steel specimens artificially contaminated with Cs+ ion. Decontamination characteristics of the stainless steel were analyzed by SEM and EPMA.

  11. Decontamination Technologies, Task 3, Urban Remediation and Response Project

    Energy Technology Data Exchange (ETDEWEB)

    Heiser,J.; Sullivan, T.

    2009-06-30

    In the aftermath of a Radiological Dispersal Device (RDD, also known as a dirty bomb) it will be necessary to remediate the site including building exteriors and interiors, equipment, pavement, vehicles, personal items etc. Remediation will remove or reduce radioactive contamination from the area using a combination of removing and disposing of many assets (including possible demolition of buildings), decontaminating and returning to service other assets, and fixing in place or leaving in place contamination that is deemed 'acceptable'. The later will require setting acceptable dose standards, which will require negotiation with all involved parties and a balance of risk and cost to benefit. To accomplish the first two, disposal or decontamination, a combination of technologies will be deployed that can be loosely classified as: Decontamination; Equipment removal and size reduction; and Demolition. This report will deal only with the decontamination technologies that will be used to return assets to service or to reduce waste disposal. It will not discuss demolition, size reduction or removal technologies or equipment (e.g., backhoe mounted rams, rock splitter, paving breakers and chipping hammers, etc.). As defined by the DOE (1994), decontamination is removal of radiological contamination from the surfaces of facilities and equipment. Expertise in this field comes primarily from the operation and decommissioning of DOE and commercial nuclear facilities as well as a small amount of ongoing research and development closely related to RDD decontamination. Information related to decontamination of fields, buildings, and public spaces resulting from the Goiania and Chernobyl incidents were also reviewed and provide some meaningful insight into decontamination at major urban areas. In order to proceed with decontamination, the item being processed needs to have an intrinsic value that exceeds the cost of the cleaning and justifies the exposure of any workers

  12. Decision Analysis System for Selection of Appropriate Decontamination Technologies

    Energy Technology Data Exchange (ETDEWEB)

    Ebadian, M.A.; Boudreaux, J.F.; Chinta, S.; Zanakis, S.H.

    1998-01-01

    The principal objective for designing Decision Analysis System for Decontamination (DASD) is to support DOE-EM's endeavor to employ the most efficient and effective technologies for treating radiologically contaminated surfaces while minimizing personnel and environmental risks. DASD will provide a tool for environmental decision makers to improve the quality, consistency, and efficacy of their technology selection decisions. The system will facilitate methodical comparisons between innovative and baseline decontamination technologies and aid in identifying the most suitable technologies for performing surface decontamination at DOE environmental restoration sites.

  13. [Advances of portable electrocardiogram monitor design].

    Science.gov (United States)

    Ding, Shenping; Wang, Yinghai; Wu, Weirong; Deng, Lingli; Lu, Jidong

    2014-06-01

    Portable electrocardiogram monitor is an important equipment in the clinical diagnosis of cardiovascular diseases due to its portable, real-time features. It has a broad application and development prospects in China. In the present review, previous researches on the portable electrocardiogram monitors have been arranged, analyzed and summarized. According to the characteristics of the electrocardiogram (ECG), this paper discusses the ergonomic design of the portable electrocardiogram monitor, including hardware and software. The circuit components and software modules were parsed from the ECG features and system functions. Finally, the development trend and reference are provided for the portable electrocardiogram monitors and for the subsequent research and product design.

  14. Decontaminating soil organic pollutants with manufactured nanoparticles.

    Science.gov (United States)

    Li, Qi; Chen, Xijuan; Zhuang, Jie; Chen, Xin

    2016-06-01

    Organic pollutants in soils might threaten the environmental and human health. Manufactured nanoparticles are capable to reduce this risk efficiently due to their relatively large capacity of sorption and degradation of organic pollutants. Stability, mobility, and reactivity of nanoparticles are prerequisites for their efficacy in soil remediation. On the basis of a brief introduction of these issues, this review provides a comprehensive summary of the application and effectiveness of various types of manufactured nanoparticles for removing organic pollutants from soil. The main categories of nanoparticles include iron (oxides), titanium dioxide, carbonaceous, palladium, and amphiphilic polymeric nanoparticles. Their advantages (e.g., unique properties and high sorption capacity) and disadvantages (e.g., high cost and low recovery) for soil remediation are discussed with respect to the characteristics of organic pollutants. The factors that influence the decontamination effects, such as properties, surfactants, solution chemistry, and soil organic matter, are addressed.

  15. Decontamination, decommissioning, and vendor advertorial issue, 2008

    Energy Technology Data Exchange (ETDEWEB)

    Agnihotri, Newal (ed.)

    2008-07-15

    The focus of the July-August issue is on Decontamination, decommissioning, and vendor advertorials. Articles and reports in this issue include: D and D technical paper summaries; The role of nuclear power in turbulent times, by Tom Chrisopher, AREVA, NP, Inc.; Enthusiastic about new technologies, by Jack Fuller, GE Hitachi Nuclear Energy; It's important to be good citizens, by Steve Rus, Black and Veatch Corporation; Creating Jobs in the U.S., by Guy E. Chardon, ALSTOM Power; and, and, An enviroment and a community champion, by Tyler Lamberts, Entergy Nuclear Operations, Inc. The Industry Innovations article is titled Best of the best TIP achievement 2008, by Edward Conaway, STP Nuclear Operating Company.

  16. ONLINE MEASUREMENT OF THE PROGRESS OF DECONTAMINATION

    Energy Technology Data Exchange (ETDEWEB)

    M.A. Ebadian, Ph.D.

    1999-01-01

    In order to determine if the sensor technology and the decontamination technology will face problems once integrated, a feasibility study (see Appendix B) was produced in which the effect of motion on the efficiency of a radiation sensor was measured. It was found that the effect is not negligible; however, it is not catastrophic, and if the sensors are properly calibrated, this obstacle can be overcome. During the first year of this project, many important tasks have been accomplished. The search for radiation sensors provided knowledge on the technologies commercially available. This, in turn, allowed for a proper assessment of the properties, limitations, different methods of measurement, and requirements of a large number of sensors. The best possible characterization and data collection instrument and decontamination technologies were chosen using the requirement information in Appendix A. There are technical problems with installing sensors within the blasting head, such as steel shot and dust interference. Therefore, the sensor array is placed so that it will measure the radioactivity after the blasting. Sensors are rather sensitive, and therefore it is not feasible to place the sensor windows in such an abrasive environment. Other factors, such as the need for radiation hardening in extreme cases, and the possible interference of gamma rays with the radio frequency modem, have been considered. These factors are expected to be negligible and can be revisited at the time of prototype production. Factors that need to be addressed are the vibrations of the blasting unit and how to isolate the sensor array from these. In addition, an electromagnetic survey must be performed to ensure there will be no interference with the electronic component that will be integrated. The integration design is shown in section 4.0.

  17. Microbial decontamination of uranium mine drainage

    Energy Technology Data Exchange (ETDEWEB)

    Hard, B.C.; Babel, W. [UFZ - Umweltforschungszentrum Leipzig-Halle GmbH, Leipzig (Germany)

    2001-07-01

    One of the problems one is faced with when uranium mines are closed is the decontamination of acid mine drainage (AMD) from tailings and flooding of the underground mines. The high concentrations of sulfates and metals in mining water make it impossible to dispose of the water into rivers without having to decontaminate it first. A bioremediation process is proposed in which sulfate-reducing bacteria are used to remove metals, neutralize the water and reduce the sulfate concentrations. Methylotrophic sulfate-reducing strains have been isolated which can be used in such a process. Lab scale experiments with different reactor types were carried out in order to find the optimum design for this bioremediation process. Comparisons were made between methanol and other electron donors with regards to their suitability as substrate for this process. Methanol was found to be most suited. Laboratory data suggest that immobilizing the bacteria on pumice particles increases the sulfate-reduction rate (SRR) up to three fold to 18 mg/l.h, compared to the rates of free flowing cells of between 3.7 and 6.8 mg/l.h. Preliminary experiments on a larger scale (15 l) using acid mine drainage pH 2.5 show SRR of 0.71 mg/l.h. In biosorption experiments up to 140 mg of aluminium per g biomass was removed from the water. One strain was found to reduce uranium VI, thus changing it from the soluble to the insoluble form. The application of the proposed process with regards to bioremediation of AMD are discussed. (orig.)

  18. Portable sensor for hazardous waste

    Energy Technology Data Exchange (ETDEWEB)

    Piper, L.G.; Fraser, M.E.; Davis, S.J. [Physical Sciences Inc., Andover, MA (United States)

    1995-10-01

    We are beginning the second phase of a three and a half year program designed to develop a portable monitor for sensitive hazardous waste detection. The ultimate goal of the program is to develop our concept to the prototype instrument level. Our monitor will be a compact, portable instrument that will allow real-time, in situ, monitoring of hazardous wastes. This instrument will be able to provide the means for rapid field screening of hazardous waste sites to map the areas of greatest contamination. Remediation efforts can then focus on these areas. Further, our instrument can show whether cleanup technologies are successful at reducing hazardous materials concentrations below regulated levels, and will provide feedback to allow changes in remediation operations, if necessary, to enhance their efficacy.

  19. Microprocessor controlled portable TLD system

    Science.gov (United States)

    Apathy, I.; Deme, S.; Feher, I.

    1996-01-01

    An up-to-date microprocessor controlled thermoluminescence dosemeter (TLD) system for environmental and space dose measurements has been developed. The earlier version of the portable TLD system, Pille, was successfully used on Soviet orbital stations as well as on the US Space Shuttle, and for environmental monitoring. The new portable TLD system, Pille'95, consists of a reader and TL bulb dosemeters, and each dosemeter is provided with an EEPROM chip for automatic identification. The glow curve data are digitised and analysed by the program of the reader. The measured data and the identification number appear on the LED display of the reader. Up to several thousand measured data together with the glow curves can be stored on a removable flash memory card. The whole system is supplied either from built-in rechargeable batteries or from the mains of the space station.

  20. iPad Portable Genius

    CERN Document Server

    McFedries, Paul

    2010-01-01

    Everything everyone wants to know about using the Apple iPad. On January 27, 2010, Apple announced the latest in its line of revolutionary, ultraportable devices - the iPad. iPad Portable Genius is the latest in a line of ultra handy, go-to and goes-with you anywhere guides for getting the most out of a new Apple product. Written to provide readers with highly useful information that's easily accessible, iPad Portable Genius is full of tips, tricks and techniques for maximizing each of the iPad's most popular features.:; Designed in full-color with an Apple look and feel, and written in a hip,

  1. Portable technologies at the museum

    DEFF Research Database (Denmark)

    Svabo, Connie

    2011-01-01

    A topic of interest in contemporary museum studies is how digital technologies contribute to museum visitor experiences. Building on insights from media and technology studies that new media should be understood for how they overlap with old media, the article reports an ethnographic study...... of the intersections between the exhibition at a modern museum of natural history and three portable technologies – one of which is digital. Mobile phone cameras, exercise pamphlets and dress-up costumes link visitors with an exhibition, but they simultaneously shape this relation in their own specific directions....... This is shown by drawing on the concept of mediation as it is developed by philosopher Michel Serres and philosopher of technology Bruno Latour. The article is based on the Ph.D. thesis entitled “Portable Objects at the Museum”, defended at Roskilde University on 22 September 2010....

  2. Portable code development in C

    Energy Technology Data Exchange (ETDEWEB)

    Brown, S.A.

    1990-11-06

    With a new generation of high performance computers appearing around us on a time scale of months, a new challenge for developers of simulation codes is to write and maintain production codes that are both highly portable and maximally efficient. My contention is that C is the language that is both best suited to that goal and is widely available today. GLF is a new code written mainly in C which is intended to have all of the XRASER physics and run on any platform of interest. It demonstrates the power of the C paradigm for code developers and flexibility and ease of use for the users. Three fundamental problems are discussed: the C/UNIX development environment; the supporting tools and libraries which handle data and graphics portability issues; and the advantages of C in numerical simulation code development.

  3. Portable High Voltage Impulse Generator

    Directory of Open Access Journals (Sweden)

    S. Gómez

    2011-07-01

    Full Text Available This paper presents a portable high voltage impulse generator which was designed and built with insulation up to 20 kV. This design was based on previous work in which simulation software for standard waves was developed. Commercial components and low-cost components were used in this work; however, these particular elements are not generally used for high voltage applications. The impulse generators used in industry and laboratories are usually expensive; they are built to withstand extra high voltage and they are big, making them impossible to transport. The proposed generator is portable, thereby allowing tests to be made on devices that cannot be moved from their location. The results obtained with the proposed impulse generator were satisfactory in terms of time and waveforms compared to other commercial impulse generators and the standard impulse wave simulator.

  4. Portable telepathology: methods and tools.

    Science.gov (United States)

    Alfaro, Luis; Roca, Ma José

    2008-07-15

    Telepathology is becoming easier to implement in most pathology departments. In fact e-mail image transmit can be done from almost any pathologist as a simplistic telepathology system. We tried to develop a way to improve capabilities of communication among pathologists with the idea that the system should be affordable for everybody. We took the premise that any pathology department would have microscopes and computers with Internet connection, and selected a few elements to convert them into a telepathology station. Needs were reduced to a camera to collect images, a universal microscope adapter for the camera, a device to connect the camera to the computer, and a software for the remote image transmit. We found out a microscope adapter (MaxView Plus) that allowed us connect almost any domestic digital camera to any microscope. The video out signal from the camera was sent to the computer through an Aver Media USB connector. At last, we selected a group of portable applications that were assembled into a USB memory device. Portable applications are computer programs that can be carried generally on USB flash drives, but also in any other portable device, and used on any (Windows) computer without installation. Besides, when unplugging the device, none of personal data is left behind. We selected open-source applications, and based the pathology image transmission to VLC Media Player due to its functionality as streaming server, portability and ease of use and configuration. Audio transmission was usually done through normal phone lines. We also employed alternative videoconferencing software, SightSpeed for bi-directional image transmission from microscopes, and conventional cameras allowing visual communication and also image transmit from gross pathology specimens. All these elements allowed us to install and use a telepathology system in a few minutes, fully prepared for real time image broadcast.

  5. Portable Presentation And Instruction Unit

    Science.gov (United States)

    Christman, L.; Hoang, N.

    1994-01-01

    Proposed electronic display unit reminiscent of kiosk serves as portable, interactive, multimedia information terminal. Used as traveling science exhibit, aid for teaching science in schools, or training and skill-refresher device for space flight crews. Provides interactive video and audio displays, including three-dimensional-appearing video simulations. Speeds learning and improves retention by applying principles of scientific visualization. Also helps previously trained but recently unpracticed personnel relearn special skills and procedures quickly.

  6. Software Complexity Threatens Performance Portability

    Energy Technology Data Exchange (ETDEWEB)

    Gamblin, T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-09-11

    Modern HPC software packages are rarely self-contained. They depend on a large number of external libraries, and many spend large fractions of their runtime in external subroutines. Performance portability depends not only on the effort of application teams, but also on the availability of well-tuned libraries. At most sites, the burden of maintaining libraries is shared by code teams and facilities. Facilities typically provide well-tuned default versions, but code teams frequently build with bleeding-edge compilers to achieve high performance. For this reason, HPC has no “standard” software stack, unlike other domains where performance is not critical. Incompatibilities among compilers and software versions force application teams and facility staff to re-build custom versions of libraries for each new toolchain. Because the number of potential configurations is combinatorial, and because HPC software is notoriously difficult to port to new machines [3, 7, 8], the tuning effort required to support and maintain performance-portable libraries outstrips the available manpower at most sites. Software complexity is a growing obstacle to performance portability for HPC.

  7. A Portable Passive Physiotherapeutic Exoskeleton

    Directory of Open Access Journals (Sweden)

    Dasheek Naidu

    2012-10-01

    Full Text Available The public healthcare system in South Africa is in need of urgent attention in no small part because there has been an escalation in the number of stroke victims which could be due to the increase in hypertension in this urbanizing society. There is a growing need for physiotherapists and occupational therapists in the country, which is further hindered by the division between urban and rural areas. A possible solution is a portable passive physiotherapeutic exoskeleton device. The exoskeleton device has been formulated to encapsulate methodologies that enable the anthropomorphic integration between a biological and mechatronic limb. A physiotherapeutic mechanism was designed to be portable and adjustable, without limiting the spherical motion and workspace of the human arm. The exoskeleton was designed to be portable in the sense that it could be transported geographically. It is a complete device allowing for motion in the shoulder, elbow, wrist and hand joints. The inverse kinematics was solved iteratively via the Damped Least Squares (DLS method. The electronic and computer system allowed for professional personnel to either change an individual joint or a combination of joints angles via the kinematic models. A ramp PI controller was established to provide a smooth response to simulate the passive therapy motion.

  8. Evaluation of Cost and Effectiveness of Decontamination Scenarios on External Radiation Exposure in Fukushima

    Energy Technology Data Exchange (ETDEWEB)

    Yasutaka, T.; Naito, W. [National Institute of Advanced Industrial Science and Technology (Japan)

    2014-07-01

    Despite the enormous cost associated with radiation decontamination, almost no quantitative assessment has been performed on the relationship between the potential reduction in long-term radiation exposure and the costs of the various decontamination strategies considered for the decontamination areas in Fukushima. In order to establish effective and pragmatic decontamination strategies for use in the radiation contaminated areas in Fukushima, a holistic approach for assessing decontamination strategies, their costs, and long-term external radiation doses is needed. The objective of the present study is to evaluate the cost and effectiveness of decontamination scenarios in the decontamination areas in Fukushima in regard to external radiation exposure. The choice of decontamination strategies in the decontamination areas should be based on a comprehensive analysis of multiple attributes such as radiological, economic, and socio-psychological attributes. The cost and effectiveness of the different decontamination strategies is not sole determinant of the decontamination strategies of the special decontamination area but is one of the most important attributes when making the policy decision. In the current study, we focus on radiological and economic attributes in determining decontamination strategies. A geographical information system (GIS) was used to relate the predicted external dose in the affected areas to the number of potential inhabitants and the land use in the areas. A comprehensive review of the costs of various decontamination methods was conducted as part of the analysis. The results indicate that aerial decontamination in the special decontamination areas in Fukushima would be effective for reducing the air dose rate to the target level in a short period of time in some but not all of the areas. In a standard scenario, the analysis of cost suggests that decontamination costs of decontamination in Fukushima was estimated to be up to approximately 5

  9. Biological decontamination of surfaces using guided ionization waves

    Science.gov (United States)

    Jarrige, Julien; Zaepffel, Clement

    2016-09-01

    Atmospheric pressure plasma jets have received an increasing attention these last ten years in various domains, including biomedical applications and decontamination. Among these technologies, guided ionization waves (also called ``plasma bullets'') are very promising because of their ability to produce a highly non-equilibrium plasma. Reactive species can be generated in the open air over a long distance during the propagation of the wave (typically: several cm), while the background gas remains at ambient temperature. A non-thermal plasma system has been developed and tested for the biological decontamination of surfaces. It consists of a dielectric barrier discharge in a helium flow driven by high voltage pulses. The propagation of the ionization wave and the spatial distribution of the species have been characterized by high speed imaging and optical emission spectroscopy. The influence of the discharge parameters on the plasma properties is investigated. Results of decontamination on several bacteria are shown, and the decontamination efficiency is compared with the plasma properties.

  10. Steam Generator Group Project. Task 6. Channel head decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Allen, R.P.; Clark, R.L.; Reece, W.D.

    1984-08-01

    The Steam Generator Group Project utilizes a retired-from-service pressurized-water-reactor steam generator as a test bed and source of specimens for research. An important preparatory step to primary side research activities was reduction of the radiation field in the steam generator channel head. This task report describes the channel head decontamination activities. Though not a programmatic research objective it was judged beneficial to explore the use of dilute reagent chemical decontamination techniques. These techniques presented potential for reduced personnel exposure and reduced secondary radwaste generation, over currently used abrasive blasting techniques. Two techniques with extensive laboratory research and vendors prepared to offer commercial application were tested, one on either side of the channel head. As indicated in the report, both techniques accomplished similar decontamination objectives. Neither technique damaged the generator channel head or tubing materials, as applied. This report provides details of the decontamination operations. Application system and operating conditions are described.

  11. Modification of the Decontamination Facility at the Kruemmel NPP - 13451

    Energy Technology Data Exchange (ETDEWEB)

    Klute, Stefan; Kupke, Peter [Siempelkamp Nukleartechnik GmbH Am Taubenfeld 25/1, 69123 Heidelberg (Germany)

    2013-07-01

    In February 2009, Siempelkamp Nukleartechnik GmbH was awarded the contract for the design, manufacture, delivery and construction of a new Decontamination Facility in the controlled area for Kruemmel NPP. The new decontamination equipment has been installed according to the state of art of Kruemmel NPP. The existing space required the following modification, retrofitting and reconstruction works: - Demounting of the existing installation: to create space for the new facility it was necessary to dismantle the old facility. The concrete walls and ceilings were cut into sizes of no more than 400 kg for ease of handling. This enabled decontamination so largest possible amount could be released for recycling. All steel parts were cut into sizes fitting for iron-barred boxes, respecting the requirement to render the parts decontaminable and releasable. - Reconstructing a decontamination facility: Reconstruction of a decontamination box with separate air lock as access area for the decontamination of components and assemblies was conducted using pressurized air with abrasives (glass beads or steel shots). The walls were equipped with sound protection, the inner walls were welded gap-free to prevent the emergence of interstices and were equipped with changeable wear and tear curtains. Abrasive processing unit positioned underneath the dry blasting box adjacent to the two discharge hoppers. A switch has been installed for the separation of the glass beads and the steel shot. The glass beads are directed into a 200 l drum for the disposal. The steel shot was cleaned using a separator. The cleaned steel shot was routed via transportation devices to the storage container, making it available for further blasting operations. A decontamination box with separate air lock as access area for the decontamination of components and assemblies using high pressure water technology was provided by new construction. Water pressures between 160 bar and 800 bar can be selected. The inner

  12. Advance in radioactive decontamination; Avances en descontaminacion radiactiva

    Energy Technology Data Exchange (ETDEWEB)

    Basteris M, J. A. [Universidad Autonoma de Yucatan, Facultad de Medicina, Departamento de Diagnostico por Laboratorio y Gabinete, Av. Cupules No. 232, Col. Garcia Gineres, 97070 Merida, Yucatan (Mexico); Farrera V, R., E-mail: basteris@prodigy.net.m [Hospital de Especialidades de la UMAE, Centro Medico Nacional Ignacio Garcia Tellez, Departamento de Medicina Nuclear, Calle 34 x 41, Exterrenos el Fenix s/n, Col. Industrial, 91750 Merida, Yucatan (Mexico)

    2010-09-15

    The objective of the present work was to determine if the application of the Na hypochlorite has some utility in the radioactive decontamination, in comparison with the water, detergent and alcohol. Several methods were compared for decontaminate the iodine 131 and technetium 99, the work table and the skin it was carried out an initial count with the Geiger Muller. Later on, in a single occasion, the areas were washed with abundant water, alcohol, clothes detergent and sodium hypochlorite (used commercially as domestic bleacher) without diluting. Observing that the percentage in the decrease of the counted radioactivity by the Geiger Muller, decreased in the following way: It was demonstrated that the Na hypochlorite presents the highest index of radioactive decontamination with 100% of effectiveness. The Na hypochlorite is an excellent substance that can be used with effectiveness and efficiency like decontamination element in the accident cases of radioactive contamination in the clinical laboratories of nuclear medicine. (Author)

  13. Cold Atmospheric Plasma Decontamination of the Pericarps of Fruit

    National Research Council Canada - National Science Library

    Perni, Stefano; Liu, David W; Shama, Gilbert; Kong, Michael G

    2008-01-01

    .... The operating voltage necessary for efficient microbial decontamination of fruit pericarps was first established using Escherichia coli at a concentration of 107 CFU/cm2 on the surface of mango...

  14. Enhanced toxic cloud knockdown spray system for decontamination applications

    Science.gov (United States)

    Betty, Rita G [Rio Rancho, NM; Tucker, Mark D [Albuquerque, NM; Brockmann, John E [Albuquerque, NM; Lucero, Daniel A [Albuquerque, NM; Levin, Bruce L [Tijeras, NM; Leonard, Jonathan [Albuquerque, NM

    2011-09-06

    Methods and systems for knockdown and neutralization of toxic clouds of aerosolized chemical or biological warfare (CBW) agents and toxic industrial chemicals using a non-toxic, non-corrosive aqueous decontamination formulation.

  15. Decontamination of process equipment using recyclable chelating solvent

    Energy Technology Data Exchange (ETDEWEB)

    Jevec, J.; Lenore, C.; Ulbricht, S. [Babcock & Wilcox, Co., R& DD, Alliance, OH (United States)

    1995-10-01

    The Department of Energy (DOE) is now faced with the task of meeting decontamination and decommissioning obligations at numerous facilities by the year 2019. Due to the tremendous volume of material involved, innovative decontamination technologies are being sought that can reduce the volumes of contaminated waste materials and secondary wastes requiring disposal. This report describes the results of the performance testing of chelates and solvents for the dissolution of uranium.

  16. Evaluation of Five Decontamination Methods for Filtering Facepiece Respirators

    OpenAIRE

    Viscusi, Dennis J.; Bergman, Michael S.; Eimer, Benjamin C.; Ronald E. Shaffer

    2009-01-01

    Concerns have been raised regarding the availability of National Institute for Occupational Safety and Health (NIOSH)-certified N95 filtering facepiece respirators (FFRs) during an influenza pandemic. One possible strategy to mitigate a respirator shortage is to reuse FFRs following a biological decontamination process to render infectious material on the FFR inactive. However, little data exist on the effects of decontamination methods on respirator integrity and performance. This study eval...

  17. Recent developments in collaborative CBRN decontamination science : a retrospective

    Energy Technology Data Exchange (ETDEWEB)

    Yanofsky, N. [Defence Research and Development Canada, Ottawa, ON (Canada); Volchek, K.; Fingas, M. [Environment Canada, Ottawa, ON (Canada). Emergencies Science and Technology Division, Environmental Technology Centre, Science and Technology Branch; Filatov, B. [Research Inst. of Hygiene, Toxicology and Occupational Pathology, Volgograd (Russian Federation)

    2006-07-01

    The importance of addressing the risk of chemical, biological and radiological/nuclear (CBRN) attacks was discussed with particular reference to recent developments in Canadian-led decontamination studies as part of the remediation response to a terrorist attack. Research efforts have been supported by government programs such as the CBRN Research and Technology Initiative of Defence Research and Development Canada and the Global Partnership Program of the Department of Foreign Affairs. In 2005, Environment Canada and Defence Research and Development Canada co-organized an international workshop with the Research Institute of Health, Toxicology and Occupational Pathology of Volgograd, Russia. The workshop brought together researchers from Canada, Russia, United States, United Kingdom, Netherlands, Poland and Bulgaria, with the view to eventually develop longer term collaborations. The theme focused on membrane technology and its application in CBRN decontamination. This paper reviewed these collaborative and international research efforts and identified areas in need of future work, such as bioremediation and radio-nuclear remediation. It addressed issues supporting a collaborative international research agenda in decontamination science; membrane filtration as a feasible approach to decontamination waste treatment; and possible areas of CBRN collaboration. It was suggested that the key to successful decontamination requires the creation of computer systems for the initial identification of chemical substances; complete toxicological characterization of the most dangerous agents; regulatory safety standards; quantitative determination of chemical substances; antidotes for most chemical threat agents; universal decontamination agents; and, validation of criteria for decontaminating buildings. The question of who pays for decontamination, be it the private or public sector, was also discussed.

  18. A survey of decontamination processes applicable to DOE nuclear facilities

    Energy Technology Data Exchange (ETDEWEB)

    Chen, L.; Chamberlain, D.B.; Conner, C.; Vandegrift, G.F.

    1997-05-01

    The objective of this survey was to select an appropriate technology for in situ decontamination of equipment interiors as part of the decommissioning of U.S. Department of Energy nuclear facilities. This selection depends on knowledge of existing chemical decontamination methods. This report provides an up-to-date review of chemical decontamination methods. According to available information, aqueous systems are probably the most universally used method for decontaminating and cleaning metal surfaces. We have subdivided the technologies, on the basis of the types of chemical solvents, into acid, alkaline permanganate, highly oxidizing, peroxide, and miscellaneous systems. Two miscellaneous chemical decontamination methods (electrochemical processes and foam and gel systems) are also described. A concise technical description of various processes is given, and the report also outlines technical considerations in the choice of technologies, including decontamination effectiveness, waste handing, fields of application, and the advantages and limitations in application. On the basis of this survey, six processes were identified for further evaluation. 144 refs., 2 tabs.

  19. Experience Practices on Decontamination Activity in NPP Decommissioning

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Suk Bon; Kim, Jeongju; Sohn, Wook [Korea Hydro and Nuclear Power Co., Daejeon (Korea, Republic of)

    2016-10-15

    Decommissioning of a nuclear power plant (NPP) involves various technical and administrative activities for a utility to terminate its license, which allows the plant site to be released from the regulatory control (site release). Decontamination activity in NPP decommissioning is one of the main technical activities to be performed during the decommissioning. The decontamination at decommissioning sites is usually performed due to several reasons such as reducing personnel dose and disposal costs, and cleanup to meet license termination requirements by using physical or chemical removal techniques proven through the previous experience practices. This paper introduces the best and worst practices for the decontamination activities collected from the decommissioning operational experiences through the implementation of nuclear decommissioning projects around the world. Review of the experiences of decontamination shows that it is important to conduct an advanced planning for optimized implementation of decontamination taking into considering site specific conditions such as operating time, reactor type, system, and so on. Also, a review of newer decontamination methods is necessary to safely and economically decommission the nuclear facility.

  20. Reducing Risk of Salmonellosis through Egg Decontamination Processes

    Directory of Open Access Journals (Sweden)

    Thilini Piushani Keerthirathne

    2017-03-01

    Full Text Available Eggs have a high nutritional value and are an important ingredient in many food products. Worldwide foodborne illnesses, such as salmonellosis linked to the consumption of eggs and raw egg products, are a major public health concern. This review focuses on previous studies that have investigated the procedures for the production of microbiologically safe eggs. Studies exploring pasteurization and decontamination methods were investigated. Gamma irradiation, freeze drying, hot air, hot water, infra-red, atmospheric steam, microwave heating and radiofrequency heating are all different decontamination methods currently considered for the production of microbiologically safe eggs. However, each decontamination procedure has different effects on the properties and constituents of the egg. The pasteurization processes are the most widely used and best understood; however, they influence the coagulation, foaming and emulsifying properties of the egg. Future studies are needed to explore combinations of different decontamination methods to produce safe eggs without impacting the protein structure and usability. Currently, eggs which have undergone decontamination processes are primarily used in food prepared for vulnerable populations. However, the development of a decontamination method that does not affect egg properties and functionality could be used in food prepared for the general population to provide greater public health protection.

  1. Reducing Risk of Salmonellosis through Egg Decontamination Processes.

    Science.gov (United States)

    Keerthirathne, Thilini Piushani; Ross, Kirstin; Fallowfield, Howard; Whiley, Harriet

    2017-03-22

    Eggs have a high nutritional value and are an important ingredient in many food products. Worldwide foodborne illnesses, such as salmonellosis linked to the consumption of eggs and raw egg products, are a major public health concern. This review focuses on previous studies that have investigated the procedures for the production of microbiologically safe eggs. Studies exploring pasteurization and decontamination methods were investigated. Gamma irradiation, freeze drying, hot air, hot water, infra-red, atmospheric steam, microwave heating and radiofrequency heating are all different decontamination methods currently considered for the production of microbiologically safe eggs. However, each decontamination procedure has different effects on the properties and constituents of the egg. The pasteurization processes are the most widely used and best understood; however, they influence the coagulation, foaming and emulsifying properties of the egg. Future studies are needed to explore combinations of different decontamination methods to produce safe eggs without impacting the protein structure and usability. Currently, eggs which have undergone decontamination processes are primarily used in food prepared for vulnerable populations. However, the development of a decontamination method that does not affect egg properties and functionality could be used in food prepared for the general population to provide greater public health protection.

  2. Anthrax Sampling and Decontamination: Technology Trade-Offs

    Energy Technology Data Exchange (ETDEWEB)

    Price, Phillip N.; Hamachi, Kristina; McWilliams, Jennifer; Sohn, Michael D.

    2008-09-12

    The goal of this project was to answer the following questions concerning response to a future anthrax release (or suspected release) in a building: 1. Based on past experience, what rules of thumb can be determined concerning: (a) the amount of sampling that may be needed to determine the extent of contamination within a given building; (b) what portions of a building should be sampled; (c) the cost per square foot to decontaminate a given type of building using a given method; (d) the time required to prepare for, and perform, decontamination; (e) the effectiveness of a given decontamination method in a given type of building? 2. Based on past experience, what resources will be spent on evaluating the extent of contamination, performing decontamination, and assessing the effectiveness of the decontamination in abuilding of a given type and size? 3. What are the trade-offs between cost, time, and effectiveness for the various sampling plans, sampling methods, and decontamination methods that have been used in the past?

  3. Full Scale Development and Initial Production of the Personnel/Casualty Decontamination System Skin Decontamination Kit (PCDS SDK)

    Science.gov (United States)

    1991-11-01

    contact with the Ambergard XE-555 resin. The JSOR for the SDK requires that the decontaminant must not degrade the protective characteristics of the HOPP...Joint Services Operational Requirements ( JSOR ) and AR 70-71. (Compatibility was not determined during this effort). Decontaminability is the ability of...and biological contaminants, although covered by AR 70-71. were not tested since they are not addressed in the JSOR . b. Conclusions Using thickened

  4. Selective Collection of Used Portable Batteries

    OpenAIRE

    POPIŢA Gabriela-Emilia; Antoanela POPOVICI; Raluca HAŢEGAN

    2010-01-01

    One of the main sources of pollution with heavy metals in municipal landfills, is the used portable batteries. Ananalysis of soil pollution with heavy metals from the waste landfills show that the predominantly heavy metals are: lead,zinc, cadmium, manganese and nickel.The selective collection of portable batteries has been required by EU legislation (2006) transposed in Romanianlegislation (2008), and is important because of heavy metals content of portable batteries. Under the law, the mini...

  5. The Portable Metal Detecting Meter

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Using backscatter principle of ray, one kind of the portable metal detecting meters, which comprises five parts, i.e., a ray-emitter, a ray acceptor, discriminating and forming pulse circuits, storing and processing data units, a light and sound alarm device, and a power supply, had been invented. It can judge existence of danger articles as weapons and daggers hided inside luggages, pracels, or clothing of passengers or persons without opening packing. The detecting distance between the meter and danger objects, at present, is about one meter, but can be extended adopting improvement for key parts. For comparison, up to now, in the whole world, known information

  6. Portable smartphone optical fibre spectrometer

    Science.gov (United States)

    Hossain, Md. Arafat; Canning, John; Cook, Kevin; Jamalipour, Abbas

    2015-09-01

    A low cost, optical fibre based spectrometer has been developed on a smartphone platform for field-portable spectral analysis. Light of visible wavelength is collected using a multimode optical fibre and diffracted by a low cost nanoimprinted diffraction grating. A measurement range over 300 nm span (λ = 400 to 700 nm) is obtained using the smartphone CMOS chip. The spectral resolution is Δλ ~ 0.42 nm/screen pixel. A customized Android application processed the spectra on the same platform and shares with other devices. The results compare well with commercially available spectrometer.

  7. Portable X-Ray Device

    Science.gov (United States)

    1983-01-01

    Portable x-ray instrument developed by NASA now being produced commercially as an industrial tool may soon find further utility as a medical system. The instrument is Lixiscope - Low Intensity X-Ray Imaging Scope -- a self-contained, battery-powered fluoroscope that produces an instant image through use of a small amount of radioactive isotope. Originally developed by Goddard Space Flight Center, Lixiscope is now being produced by Lixi, Inc. which has an exclusive NASA license for one version of the device.

  8. Mobile worksystems for decontamination and dismantlement

    Energy Technology Data Exchange (ETDEWEB)

    Osborn, J. [Carnegie Mellon Univ., Pittsburgh, PA (United States); Bares, L.C.; Thompson, B.R. [RedZone Robotics, Inc., Pittsburgh, PA (United States)

    1995-10-01

    Many DOE nuclear facilities have aged beyond their useful lifetimes. They need to be decommissioned in order to be safe for human presence in the short term, to eventually recover valuable materials they contain, and ultimately to be transitioned to alternative uses or green field conditions. Decontamination and dismantlement are broad classes of activities that will enable these changes to occur. Most of these facilities - uranium enrichment plants, weapons assembly plants, research and production reactors, and fuel recycling facilities - are dormant, though periodic inspection, surveillance and maintenance activities within them are on-going. DOE estimates that there are over 5000 buildings that require deactivation to reduce the costs of performing such work with manual labor. In the long term, 1200 buildings will be decommissioned, and millions of metric tons of metal and concrete will have to be recycled or disposed of. The magnitude of the problem calls for new approaches that are far more cost effective than currently available techniques. This paper describes a mobile workstation termed ROSIE, which provides remote work capabilities for D&D activities.

  9. Decontamination and decommissioning of Shippingport commercial reactor

    Energy Technology Data Exchange (ETDEWEB)

    Schreiber, J. [Dept. of Energy, Pittsburgh, PA (United States)

    1989-11-01

    To a certain degree, the decontamination and decommissioning (D and D) of the Shippingport reactor was a joint venture with Duquesne Light Company. The structures that were to be decommissioned were to be removed to at least three feet below grade. Since the land had been leased from Duquesne Light, there was an agreement with them to return the land to them in a radiologically safe condition. The total enclosure volume for the steam and nuclear containment systems was about 1.3 million cubic feet, more than 80% of which was below ground. Engineering plans for the project were started in July of 1980 and the final environmental impact statement (EIS) was published in May of 1982. The plant itself was shut down in October of 1982 for end-of-life testing and defueling. The engineering services portion of the decommissioning plans was completed in September of 1983. DOE moved onto the site and took over from the Navy in September of 1984. Actual physical decommissioning began after about a year of preparation and was completed about 44 months later in July of 1989. This paper describes the main parts of D and D.

  10. Waste Isolation Pilot Plant Salt Decontamination Testing

    Energy Technology Data Exchange (ETDEWEB)

    Rick Demmer; Stephen Reese

    2014-09-01

    On February 14, 2014, americium and plutonium contamination was released in the Waste Isolation Pilot Plant (WIPP) salt caverns. At the request of WIPP’s operations contractor, Idaho National Laboratory (INL) personnel developed several methods of decontaminating WIPP salt, using surrogate contaminants and also americium (241Am). The effectiveness of the methods is evaluated qualitatively, and to the extent possible, quantitatively. One of the requirements of this effort was delivering initial results and recommendations within a few weeks. That requirement, in combination with the limited scope of the project, made in-depth analysis impractical in some instances. Of the methods tested (dry brushing, vacuum cleaning, water washing, strippable coatings, and mechanical grinding), the most practical seems to be water washing. Effectiveness is very high, and it is very easy and rapid to deploy. The amount of wastewater produced (2 L/m2) would be substantial and may not be easy to manage, but the method is the clear winner from a usability perspective. Removable surface contamination levels (smear results) from the strippable coating and water washing coupons found no residual removable contamination. Thus, whatever is left is likely adhered to (or trapped within) the salt. The other option that shows promise is the use of a fixative barrier. Bartlett Nuclear, Inc.’s Polymeric Barrier System (PBS) proved the most durable of the coatings tested. The coatings were not tested for contaminant entrapment, only for coating integrity and durability.

  11. Decontamination method for radioactively contaminated material

    Energy Technology Data Exchange (ETDEWEB)

    Shoji, Yuichi; Mizuguchi, Hiroshi; Sakai, Hitoshi; Komatsubara, Masaru

    1998-09-02

    Radioactively contaminated materials having surfaces contaminated by radioactive materials are dissolved in molten salts by the effect of chlorine gas. The molten salts are brought into contact with a low melting point metal to reduce only radioactive materials by substitution reaction and recover them into the low melting point metal. Then, a low melting point metal phase and a molten salt phase are separated. The low melting point metal phase is evaporated to separate the radioactive materials from molten metals. On the other hand, other metal ions dissolved in the molten salts are reduced into metals by electrolysis at an anode and separated from the molten salts and served for regeneration. The low melting point metals are reutilized together with contaminated lead, after subjected to decontamination, generated from facilities such as nuclear power plant or lead for disposal. Since almost all materials including the molten salts and the molten metals can be enclosed, the amount of wastes can be reduced. In addition, radiation exposure of operators who handle them can be reduced. (T.M.)

  12. Waste Isolation Pilot Plant Salt Decontamination Testing

    Energy Technology Data Exchange (ETDEWEB)

    Demmer, Ricky Lynn [Idaho National Laboratory; Reese, Stephen Joseph [Idaho National Laboratory

    2015-03-01

    On February 14, 2014, americium and plutonium contamination was released in the Waste Isolation Pilot Plant (WIPP) salt caverns. Several practical, easily deployable methods of decontaminating WIPP salt, using a surrogate contaminant and americium (241Am), were developed and tested. The effectiveness of the methods is evaluated qualitatively, and to the extent practical, quantitatively. Of the methods tested (dry brushing, vacuum cleaning, water washing, mechanical grinding, strippable coatings, and fixative barriers), the most practical seems to be water washing. Effectiveness is very high, and water washing is easy and rapid to deploy. The amount of wastewater produced (~2 L/m2) would be substantial and may not be easy to manage, but the method is the clear winner from a usability perspective. Removable surface contamination levels (smear results) from water washed coupons found no residual removable contamination. Thus, whatever contamination is left is likely adhered to (or trapped within) the salt. The other option that shows promise is the use of a fixative barrier. Bartlett Nuclear, Inc.’s Polymeric Barrier System proved the most durable of the coatings tested. The coatings were not tested for contaminant entrapment, only for coating integrity and durability.

  13. Mycotoxins - prevention and decontamination by yeasts.

    Science.gov (United States)

    Pfliegler, Walter P; Pusztahelyi, Tünde; Pócsi, István

    2015-07-01

    The application of yeasts has great potential in reducing the economic damage caused by toxigenic fungi in the agriculture. Some yeasts may act as biocontrol agents inhibiting the growth of filamentous fungi. These species may also gain importance in the preservation of agricultural products and in the reduction of their mycotoxin contamination, yet the extent of mycotoxin production in the presence of biocontrol agents is relatively less understood. The application of yeasts in various technological processes may have a direct inhibitory effect on the toxin production of certain molds, which is independent of their growth suppressing effect. Furthermore, several yeast species are capable of accumulating mycotoxins from agricultural products, thereby effectively decontaminating them. Probiotic yeasts or products containing yeast cell wall are also applied to counteract mycotoxicosis in livestock. Several yeast strains are also able to degrade toxins to less-toxic or even non-toxic substances. This intensively researched field would greatly benefit from a deeper knowledge on the genetic and molecular basis of toxin degradation. Moreover, yeasts and their biotechnologically important enzymes may exhibit sensitivity to certain mycotoxins, thereby mounting a considerable problem for the biotechnological industry. It is noted that yeasts are generally regarded as safe; however, there are reports of toxin degrading species that may cause human fungal infections. The aspects of yeast-mycotoxin relations with a brief consideration of strain improvement strategies and genetic modification for improved detoxifying properties and/or mycotoxin resistance are reviewed here.

  14. Establishing the irradiation dose for paper decontamination

    Science.gov (United States)

    Moise, Ioan Valentin; Virgolici, Marian; Negut, Constantin Daniel; Manea, Mihaela; Alexandru, Mioara; Trandafir, Laura; Zorila, Florina Lucica; Talasman, Catalina Mihaela; Manea, Daniela; Nisipeanu, Steluta; Haiducu, Maria; Balan, Zamfir

    2012-08-01

    Museums, libraries and archives are preserving documents that are slowly degrading due to the inherent ageing of the cellulose substrate or to the technological errors of the past (acid paper, iron gall ink). Beside this, large quantities of paper are rapidly damaged by biological attacks following natural disasters and improper storage conditions. The treatment of paper documents with ionizing radiation can be used for mass decontamination of cultural heritage items but conservators and restaurators are still reserved because of the radiation induced degradation. We conducted a study for establishing the dose needed for the effective treatment of paper documents, taking into account the biological burden and the irradiation effects on paper structure. We used physical testing specific to paper industry and less destructive analytical methods (thermal analysis). Our results show that an effective treatment can be performed with doses lower than 10 kGy. Old paper appears to be less affected by gamma radiation than recent paper but the sampling is highly affected by the non-uniform degree of the initial degradation status. The extent of testing for degradation and the magnitude of acceptable degradation should take into account the biological threat and the expected life time of the paper documents.

  15. Oxidation of Ce(III) in Foam Decontaminant by Ozone

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Chong Hun; Yoon, I. H.; Choi, W. K.; Moon, J. K.; Yang, H. B. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Lee, J. S. [Gachon University, Seongnam (Korea, Republic of)

    2016-10-15

    A nanoparticle-based foam decontaminant is composed of a surfactant and nanoparticles for the generation and maintenance of foam, and a chemical decontamination agent made of Ce(IV) dissolved in nitric acid. Ce(IV) will be reduced to Ce(III) through the decontamination process. Oxidizing cerium(III) can be reused as a decontamination agent, Ce(IV). Oxidation treatment technology by ozone uses its strong oxidizing power. It can be regarded as an environmentally friendly process, because ozone cannot be stored and transported like other industrial gases (because it quickly decays into diatomic oxygen) and must therefore be produced on site, and used ozone can decompose immediately. The ozonation treatment of Ce(III) in foam decontaminant containing a surfactant is necessary for the effective regeneration of Ce(III). Thus, the present study was undertaken to determine the optimal conditions for ozonation treatment in the regeneration of Ce(III) into Ce(IV) in the nanoparticle-based foam decontaminant containing surfactant. This study was undertaken to determine the optimal conditions for ozonation treatment in the regeneration of Ce(III) to Ce(IV) in nanoparticle-based foam decontaminant containing a TBS surfactant. The oxidation conversion rate of Ce(III) was increased with an increase in the flow rate of the gas mixture and ozone injection amount. The oxidation time required for the 100% oxidation conversion of Ce(III) to Ce(IV) at a specific ozone injection amount can be predicted from these experimental data.

  16. A simplified model of decontamination by BWR steam suppression pools

    Energy Technology Data Exchange (ETDEWEB)

    Powers, D.A.

    1997-05-01

    Phenomena that can decontaminate aerosol-laden gases sparging through steam suppression pools of boiling water reactors during reactor accidents are described. Uncertainties in aerosol properties, aerosol behavior within gas bubbles, and bubble behavior in plumes affect predictions of decontamination by steam suppression pools. Uncertainties in the boundary and initial conditions that are dictated by the progression of severe reactor accidents and that will affect predictions of decontamination by steam suppression pools are discussed. Ten parameters that characterize boundary and initial condition uncertainties, nine parameters that characterize aerosol property and behavior uncertainties, and eleven parameters that characterize uncertainties in the behavior of bubbles in steam suppression pools are identified. Ranges for the values of these parameters and subjective probability distributions for parametric values within the ranges are defined. These uncertain parameters are used in Monte Carlo uncertainty analyses to develop uncertainty distributions for the decontamination that can be achieved by steam suppression pools and the size distribution of aerosols that do emerge from such pools. A simplified model of decontamination by steam suppression pools is developed by correlating features of the uncertainty distributions for total decontamination factor, DF(total), mean size of emerging aerosol particles, d{sub p}, and the standard deviation of the emerging aerosol size distribution, {sigma}, with pool depth, H. Correlations of the median values of the uncertainty distributions are suggested as the best estimate of decontamination by suppression pools. Correlations of the 10 percentile and 90 percentile values of the uncertainty distributions characterize the uncertainty in the best estimates. 295 refs., 121 figs., 113 tabs.

  17. Mass Casualty Decontamination in the United States: An Online Survey of Current Practice.

    Science.gov (United States)

    Power, Sarah; Symons, Charles; Carter, Holly; Jones, Emma; Amlôt, Richard; Larner, Joanne; Matar, Hazem; Chilcott, Robert P

    2016-01-01

    Mass casualty decontamination is a public health intervention that would be employed by emergency responders following a chemical, biological, or radiological incident. The decontamination of large numbers of casualties is currently most often performed with water to remove contaminants from the skin surface. An online survey was conducted to explore US fire departments' decontamination practices and their preparedness for responding to incidents involving mass casualty decontamination. Survey respondents were asked to provide details of various aspects of their decontamination procedures, including expected response times to reach casualties, disrobing procedures, approaches to decontamination, characteristics of the decontamination showering process, provision for special populations, and any actions taken following decontamination. The aim of the survey was to identify any differences in the way in which decontamination guidance is implemented across US states. Results revealed that, in line with current guidance, many US fire departments routinely use the "ladder-pipe system" for conducting rapid, gross decontamination of casualties. The survey revealed significant variability in ladder-pipe construction, such as the position and number of fire hoses used. There was also variability in decontamination characteristics, such as water temperature and water pressure, detergent use, and shower duration. The results presented here provide important insights into the ways in which implementation of decontamination guidance can vary between US states. These inconsistencies are thought to reflect established perceived best practices and local adaptation of response plans to address practical and logistical constraints. These outcomes highlight the need for evidence-based national guidelines for conducting mass casualty decontamination.

  18. Portable Diagnostics and Rapid Germination

    Energy Technology Data Exchange (ETDEWEB)

    Dunn, Zachary Spencer [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-12-01

    In the Bioenergy and Defense Department of Sandia National Laboratories, characterization of the BaDx (Bacillus anthracis diagnostic cartridge) was performed and rapid germination chemistry was investigated. BaDx was tested with complex sample matrixes inoculated with Bacillus anthracis, and the trials proved that BaDx will detect Bacillus anthracis in a variety of the medium, such as dirt, serum, blood, milk, and horse fluids. The dimensions of the device were altered to accommodate an E. coli or Listeria lateral flow immunoassay, and using a laser printer, BaDx devices were manufactured to identify E. coli and Listeria. Initial testing with E. coli versions of BaDx indicate that the device will be viable as a portable diagnostic cartridge. The device would be more effective with faster bacteria germination; hence studies were performed the use of rapid germination chemistry. Trials with calcium dipicolinic acid displayed increased cell germination, as shown by control studies using a microplate reader. Upon lyophilization the rapid germination chemistry failed to change growth patterns, indicating that the calcium dipicolinic acid was not solubilized under the conditions tested. Although incompatible with the portable diagnostic device, the experiments proved that the rapid germination chemistry was effective in increasing cell germination.

  19. Portable electrocardiograph through android application.

    Science.gov (United States)

    De Oliveira, Igor H; Cene, V H; Balbinot, A

    2015-01-01

    An electrocardiograph was designed and implemented, being capable of obtaining electrical signals from the heart, and sending this data via Bluetooth to a tablet, in which the signals are graphically shown. The user interface is developed as an Android application. Because of the technological progress and the increasing use of full portable systems, such as tablets and cell phones, it is important to understand the functioning and development of an application, which provides a basis for conducting studies using this technology as an interface. The project development includes concepts of electronics and its application to achieve a portable and functional final project, besides using a specific programmable integrated circuit for electrocardiogram, electroencephalogram and electromyogram, the ADS1294. Using a simulator of cardiac signals, 36 different waveforms were recorded, including normal sinus rhythm, arrhythmias and artifacts. Simulations include variations of heart rate from 30 to 190 beats per minute (BPM), with variations in peak amplitude of 1 mV to 2 mV. Tests were performed with a subject at rest and in motion, observing the signals obtained and the damage to their interpretation due to the introduction of muscle movement artifacts in motion situations.

  20. a Portable Pulsed Neutron Generator

    Science.gov (United States)

    Skoulakis, A.; Androulakis, G. C.; Clark, E. L.; Hassan, S. M.; Lee, P.; Chatzakis, J.; Bakarezos, M.; Dimitriou, V.; Petridis, C.; Papadogiannis, N. A.; Tatarakis, M.

    2014-02-01

    The design and construction of a pulsed plasma focus device to be used as a portable neutron source for material analysis such as explosive detection using gamma spectroscopy is presented. The device is capable of operating at a repetitive rate of a few Hz. When deuterium gas is used, up to 105 neutrons per shot are expected to be produced with a temporal pulse width of a few tens of nanoseconds. The pulsed operation of the device and its portable size are its main advantage in comparison with the existing continuous neutron sources. Parts of the device include the electrical charging unit, the capacitor bank, the spark switch (spark gap), the trigger unit and the vacuum-fuel chamber / anode-cathode. Numerical simulations are used for the simulation of the electrical characteristics of the device including the scaling of the capacitor bank energies with total current, the pinch current, and the scaling of neutron yields with energies and currents. The MCNPX code is used to simulate the moderation of the produced neutrons in a simplified geometry and subsequently, the interaction of thermal neutrons with a test target and the corresponding prompt γ-ray generation.

  1. Portable humanitarian mine detector overview

    Science.gov (United States)

    Allsopp, David J.; Dibsdall, Ian M.

    2002-08-01

    This paper will present an overview and early results of the QinetiQ Portable Humanitarian Mine Detector project, funded by the UK Treasury Capital Modernization Fund. The project aims to develop a prototype multi-sensor man-portable detector for humanitarian demining, drawing on experience from work for UK MoD. The project runs from July 2000 to October 2002. The project team have visited mined areas and worked closely with a number of demining organizations and a manufacturer of metal detectors used in the field. The primary objective is to reduce the number of false alarms resulting from metallic ground clutter. An analysis of such clutter items found during actual demining has shown a large proportion to be very small when compared with anti-personnel mines. The planned system integrates: a lightweight multi-element pseudo-random-code ground penetrating radar array; a pulse induction metal detector and a capacitive sensor. Data from the GPR array and metal detector are fused to provide a simple audio-visual operator interface. The capacitive sensor provides information to aid processing of the radar responses and to provide feedback to the operator of the position of the sensors above the ground. At the time of presentation the project should be in the final stages of build, prior to tests and field trials, which QinetiQ hope to carry out under the International Test and Evaluation Project (ITEP) banner.

  2. MERCURY CONTAMINATED MATERIAL DECONTAMINATION METHODS: INVESTIGATION AND ASSESSMENT

    Energy Technology Data Exchange (ETDEWEB)

    M.A. Ebadian, Ph.D.

    2001-01-01

    Over the years mercury has been recognized as having serious impacts on human health and the environment. This recognition has led to numerous studies that deal with the properties of various mercury forms, the development of methods to quantify and speciate the forms, fate and transport, toxicology studies, and the development of site remediation and decontamination technologies. This report reviews several critical areas that will be used in developing technologies for cleaning mercury from mercury-contaminated surfaces of metals and porous materials found in many DOE facilities. The technologies used for decontamination of water and mixed wastes (solid) are specifically discussed. Many technologies that have recently appeared in the literature are included in the report. Current surface decontamination processes have been reviewed, and the limitations of these technologies for mercury decontamination are discussed. Based on the currently available technologies and the processes published recently in the literature, several processes, including strippable coatings, chemical cleaning with iodine/iodide lixiviant, chemisorbing surface wipes with forager sponge and grafted cotton, and surface/pore fixation through amalgamation or stabilization, have been identified as potential techniques for decontamination of mercury-contaminated metal and porous surfaces. Their potential merits and applicability are discussed. Finally, two processes, strippable coatings and chemical cleaning with iodine/iodide lixiviant, were experimentally investigated in Phase II of this project.

  3. Electrochemical Decontamination of Painted and Heavily Corroded Metals

    Energy Technology Data Exchange (ETDEWEB)

    Marczak, S.; Anderson, J.; Dziewinski, J.

    1998-09-08

    The radioactive metal wastes that are generated from nuclear fuel plants and radiochemical laboratories are mainly contaminated by the surface deposition of radioactive isotopes. There are presently several techniques used in removing surface contamination involving physical and chemical processes. However, there has been very little research done in the area of soiled, heavily oxidized, and painted metals. Researchers at Los Alamos National Laboratory have been developing electrochemical procedures for the decontamination of bare and painted metal objects. These methods have been found to be effective on highly corroded as well as relatively new metals. This study has been successful in decontaminating projectiles and shrapnel excavated during environmental restoration projects after 40+ years of exposure to the elements. Heavily corroded augers used in sampling activities throughout the area were also successfully decontaminated. This process has demonstrated its effectiveness and offers several advantages over the present metal decontamination practices of media blasting and chemical solvents. These advantages include the addition of no toxic or hazardous chemicals, low operating temperature and pressure, and easily scaleable equipment. It is in their future plans to use this process in the decontamination of gloveboxes destined for disposal as TRU waste.

  4. Laser decontamination and decomposition of PCB-containing paint

    Science.gov (United States)

    Anthofer, A.; Kögler, P.; Friedrich, C.; Lippmann, W.; Hurtado, A.

    2017-01-01

    Decontamination of concrete surfaces contaminated with paint containing polychlorinated biphenyls is an elaborate and complex task that must be performed within the scope of nuclear power plant dismantling as well as conventional pollutant cleanup in buildings. The state of the art is mechanical decontamination, which generates dust as well as secondary waste and is both dangerous and physically demanding. Moreover, the ablated PCB-containing paint has to be treated in a separate process step. Laser technology offers a multitude of possibilities for contactless surface treatment with no restoring forces and a high potential for automation. An advanced experimental setup was developed for performing standard laser decontamination investigations on PCB-painted concrete surfaces. As tested with epoxy paints, a high-power diode laser with a laser power of 10 kW in continuous wave (CW) mode was implemented and resulted in decontamination of the concrete surfaces as well as significant PCB decomposition. The experimental results showed PCB removal of 96.8% from the concrete surface and PCB decomposition of 88.8% in the laser decontamination process. Significant PCDD/F formation was thereby avoided. A surface ablation rate of approx. 7.2 m2/h was realized.

  5. Modelling Mass Casualty Decontamination Systems Informed by Field Exercise Data

    Directory of Open Access Journals (Sweden)

    Richard Amlôt

    2012-10-01

    Full Text Available In the event of a large-scale chemical release in the UK decontamination of ambulant casualties would be undertaken by the Fire and Rescue Service (FRS. The aim of this study was to track the movement of volunteer casualties at two mass decontamination field exercises using passive Radio Frequency Identification tags and detection mats that were placed at pre-defined locations. The exercise data were then used to inform a computer model of the FRS component of the mass decontamination process. Having removed all clothing and having showered, the re-dressing (termed re-robing of casualties was found to be a bottleneck in the mass decontamination process during both exercises. Computer simulations showed that increasing the capacity of each lane of the re-robe section to accommodate 10 rather than five casualties would be optimal in general, but that a capacity of 15 might be required to accommodate vulnerable individuals. If the duration of the shower was decreased from three minutes to one minute then a per lane re-robe capacity of 20 might be necessary to maximise the throughput of casualties. In conclusion, one practical enhancement to the FRS response may be to provide at least one additional re-robe section per mass decontamination unit.

  6. Ecological effects of selective decontamination on resistant gram-negative bacterial colonization.

    NARCIS (Netherlands)

    Oostdijk, E.A.; Smet, A.M. de; Blok, H.E.; Thieme Groen, E.S.; Asselt, G.J. van; Benus, R.F.; Bernards, S.A.; Frenay, I.H.; Jansz, A.R.; Jongh, B.M. de; Kaan, J.A.; Leverstein-van Hall, M.A.; Mascini, E.M.; Pauw, W.; Sturm, P.D.J.; Thijsen, S.F.; Kluytmans, J.A.; Bonten, M.J.

    2010-01-01

    RATIONALE: Selective digestive tract decontamination (SDD) and selective oropharyngeal decontamination (SOD) eradicate gram-negative bacteria (GNB) from the intestinal and respiratory tract in intensive care unit (ICU) patients, but their effect on antibiotic resistance remains controversial. OBJECT

  7. Selective decontamination of the oropharynx and the digestive tract in ICU patients

    NARCIS (Netherlands)

    de Smet, A.M.G.A.

    2009-01-01

    Background: Selective Digestive tract Decontamination (SDD) and Selective Oropharyngeal Decontamination (SOD) are effective infection prevention measures in intensive care patients, but reported effects on patient outcome are conflicting and the effects on infections and respiratory tract colonizati

  8. Ecological Effects of Selective Decontamination on Resistant Gram-negative Bacterial Colonization

    NARCIS (Netherlands)

    Oostdijk, Evelien A. N.; de Smet, Anne Marie G. A.; Blok, Hetty E. M.; Groen, Emily S. Thieme; van Asselt, Gerard J.; Benus, Robin F. J.; Bernards, Sandra A. T.; Frenay, Ine H. M. E.; Jansz, Arjan R.; de Jongh, Bartelt M.; Kaan, Jan A.; Leverstein-van Hall, Maurine A.; Mascini, Ellen M.; Pauw, Wouter; Sturm, Patrick D. J.; Thijsen, Steven F. T.; Kluytmans, Jan A. J. W.; Bonten, Marc J. M.

    2010-01-01

    Rationale: Selective digestive tract decontamination (SDD) and selective oropharyngeal decontamination (SOD) eradicate gram-negative bacteria (GNB) from the intestinal and respiratory tract in intensive care unit (ICU) patients, but their effect on antibiotic resistance remains controversial. Object

  9. The Economics of Educational Software Portability.

    Science.gov (United States)

    Oliveira, Joao Batista Araujo e

    1990-01-01

    Discusses economic issues that affect the portability of educational software. Topics discussed include economic reasons for portability, including cost effectiveness; the nature and behavior of educational computer software markets; the role of producers, buyers, and consumers; potential effects of government policies; computer piracy; and…

  10. 77 FR 31894 - Portable Gauge Licenses

    Science.gov (United States)

    2012-05-30

    ... COMMISSION Portable Gauge Licenses AGENCY: Nuclear Regulatory Commission. ACTION: Draft NUREG; request for... guidance for portable gauge licensees. The NRC is requesting public comment on NUREG-1556, Volume 1...- 4737, or by email to pdr.resource@nrc.gov . The NUREG-1556, Volume 1, Revision 2, is under...

  11. Decontamination Systems Information and Reseach Program

    Energy Technology Data Exchange (ETDEWEB)

    Cook, Echol E

    1998-04-01

    The following paragraphs comprise the research efforts during the first quarter of 1998 (January 1 - March 31). These tasks have been granted a continuation from the 1997 work and will all end in June 1998. This report represents the last technical quarterly report deliverable for the WVU Cooperative Agreement - Decontamination Systems Information and Research Program. Final reports for all of the 1997 projects will be submitted afterwards as one document. During this period, groundwater extraction operations were completed on Task 1.6 - Pilot Scale Demonstration of TCE Flushing Through PVDs at the DOE/RMI Extrusion Plant. The data have been evaluated and graphs are presented. The plot of TCE Concentration versus Time shows that the up-gradient groundwater monitoring well produced consistent levels of TCE contamination. A similar trend was observed for the down-gradient wells via grab samples tested. Groundwater samples from the PVD test pad Zone of Influence showed consistent reductions in TCE concentrations with respect to time. In addition, a natural pulse frequency is evident which will have a significant impact on the efficiency of the contaminant removal under natural groundwater advection/diffusion processes. The relationships between the PVD Extraction Flow Rate versus Cumulative Time shows a clear trend in flow rate. Consistent values between 20 to 30 g.p.m. at the beginning of the extraction duration, to less than 10 g.p.m. by the end of the extraction cycle are observed. As evidenced by the aquifer's diminishing recharge levels, the PVD extraction is affecting the response of the aquifer's natural attenuation capability. Progress was also marked on the Injection and Circulation of Potable Water Through PVDs task. Data reduction from this sequence of testing is ongoing. Work planned for next quarter includes completing the Injection / Extraction of potable water task and beginning the Surfactant Injection and removal task.

  12. Encryption And Portable Data Storage

    Directory of Open Access Journals (Sweden)

    Cynthia L. Knott

    2011-04-01

    Full Text Available The protection of data is key issue in today’s world. The wide of availability and use of portable technologies such as USB flash has increased concern about securing the data resides on these devices. Because USB flash drives are small, relatively inexpensive, and easy to use, the security of the information stored on these thumb drives is on-going concern. A number of approaches to safeguarding the information stored on these drives are available. This paper examines one approach to this goal through the use of encryption. This method encrypts all the data on the drive. In addition the fact the data on the drive is encrypted is not visually obvious when viewing the contents of the disk. The proposed approach uses publically available and free encryption algorithms. A user password is needed to view and access the data that has been encrypted.  The proposed methodology is quick and easy to use. Individuals who routinely carry around their USB drives need to be able to decrypt and encrypt the device quickly and conveniently. Furthermore, if the device is lost, it is still possible with the method advocated in this paper to include information about how to return the device to the owner without compromising the secured data on the drive. Without encrypting the data on portable drives, the user risks the disclosure of information. This paper argues that portable storage should be secured and suggests a way to secure the data through password and encryption that further enhances the usability and flexibility of the USB flash drive.  The paper includes the results and analysis of an undergraduate student survey that determined what habits and practices they followed with respect to securing their personal data and files.  Some of the questions included in the analysis are the following: Do you encrypt your USB flash drive?Do you use any type of security for your USB flash drive?How important do you think security is for a flash drive? (A

  13. Decomposition Technology Development of Organic Component in a Decontamination Waste Solution

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Chong Hun; Oh, W. Z.; Won, H. J.; Choi, W. K.; Kim, G. N.; Moon, J. K

    2007-11-15

    Through the project of 'Decomposition Technology Development of Organic Component in a Decontamination Waste Solution', the followings were studied. 1. Investigation of decontamination characteristics of chemical decontamination process 2. Analysis of COD, ferrous ion concentration, hydrogen peroxide concentration 3. Decomposition tests of hardly decomposable organic compounds 4. Improvement of organic acid decomposition process by ultrasonic wave and UV light 5. Optimization of decomposition process using a surrogate decontamination waste solution.

  14. A Rapid and Inexpensive Bioassay to Evaluate the Decontamination of Organophosphates

    Science.gov (United States)

    2012-01-01

    anydrolase (a hydrolyzing enzyme ), and decon- taminating foam with hydrogen peroxide. Much of the research required to quantify CWA decontamination re...household cleaners as potential decontaminating agents, but only 5% bleach was effective at improving survival of insects on steel plates treated...required to obtain nearly complete decontamination of malathion. The bioassay was also used to screen common household cleaners as potential decontaminating

  15. Biophysical Evaluation of Food Decontamination Effects on Tissue and Bacteria

    DEFF Research Database (Denmark)

    Andersen, Ann Zahle; Duelund, Lars; Brewer, Jonathan R.

    2011-01-01

    employ differential scanning calorimetry, second harmonics generation imaging microscopy, two-photon fluorescence microscopy, and green fluorescence protein-expressing bacteria and compare our results with those obtained by traditional methods of food quality and safety evaluations. Our results show......Traditionally, the effects and efficiency of food surface decontamination processes, such as chlorine washing, radiation, or heating, have been evaluated by sensoric analysis and colony-forming unit (CFU) counts of surface swabs or carcass rinses. These methods suffice when determining probable...... in both food surface and bacteria upon surface decontamination by SonoSteam®. SonoSteam® is a recently developed method of food surface decontamination, which employs steam and ultrasound for effective heat transfer and short treatment times, resulting in significant reduction in surface bacteria. We...

  16. Criteria for the evaluation of a dilute decontamination demonstration

    Energy Technology Data Exchange (ETDEWEB)

    FitzPatrick, V.F.; Divine, J.R.; Hoenes, G.R.; Munson, L.F.; Card, C.J.

    1981-12-01

    This document provides the prerequisite technical information required to evaluate and/or develop a project to demonstrate the dilute chemical decontamination of the primary coolant system of light water reactors. The document focuses on five key areas: the basis for establishing programmatic prerequisites and the key decision points that are required for proposal evaluation and/or RFP (Request for Proposal) issuance; a technical review of the state-of-the-art to identify the potential impacts of a reactor's primary-system decontamination on typical BWR and PWR plants; a discussion of the licensing, recertification, fuel warranty, and institutional considerations and processes; a preliminary identification and development of the selection criteria for the reactor and the decontamination process; and a preliminary identification of further research and development that might be required.

  17. Systems analysis of decontamination options for civilian vehicles.

    Energy Technology Data Exchange (ETDEWEB)

    Foltz, Greg W.; Hoette, Trisha Marie

    2010-11-01

    The objective of this project, which was supported by the Department of Homeland Security (DHS) Science and Technology Directorate (S&T) Chemical and Biological Division (CBD), was to investigate options for the decontamination of the exteriors and interiors of vehicles in the civilian setting in order to restore those vehicles to normal use following the release of a highly toxic chemical. The decontamination of vehicles is especially challenging because they often contain sensitive electronic equipment, multiple materials some of which strongly adsorb chemical agents, and in the case of aircraft, have very rigid material compatibility requirements (i.e., they cannot be exposed to reagents that may cause even minor corrosion). A systems analysis approach was taken examine existing and future civilian vehicle decontamination capabilities.

  18. Biophysical Evaluation of Food Decontamination Effects on Tissue and Bacteria

    DEFF Research Database (Denmark)

    Andersen, Ann Zahle; Duelund, Lars; Brewer, Jonathan R.

    2011-01-01

    Traditionally, the effects and efficiency of food surface decontamination processes, such as chlorine washing, radiation, or heating, have been evaluated by sensoric analysis and colony-forming unit (CFU) counts of surface swabs or carcass rinses. These methods suffice when determining probable...... consumer responses or meeting legislative contamination limits. However, in the often very costly, optimization process of a new method, more quantitative and unbiased results are invaluable. In this study, we employed a biophysical approach for the investigation of qualitative and quantitative changes...... in both food surface and bacteria upon surface decontamination by SonoSteam®. SonoSteam® is a recently developed method of food surface decontamination, which employs steam and ultrasound for effective heat transfer and short treatment times, resulting in significant reduction in surface bacteria. We...

  19. Testing and evaluation of electrokinetic decontamination of concrete

    Energy Technology Data Exchange (ETDEWEB)

    DePaoli, D.W.; Harris, M.T.; Ally, M.R. [Oak Ridge National Lab., TN (United States). Chemical Technology Div.] [and others

    1996-10-01

    The goals and objectives of the technical task plan (TTP) are to (1) describe the nature and extent of concrete contamination within the Department of Energy (DOE) complex and emerging and commercial technologies applicable to these problems; (2) to match technologies to the concrete problems and recommend up to four demonstrations; (3) to initiate recommended demonstrations; and (4) to continue investigation and evaluation of the application of electrokinetic decontamination processes to concrete. This document presents findings of experimental and theoretical studies of the electrokinetic decontamination (EK) process and their implications for field demonstrations. This effort is an extension of the work performed under TTP 142005, ``Electroosmotic Concrete Decontamination. The goals of this task were to determine the applicability of EK for treating contaminated concrete and, if warranted, to evaluate EK as a potential technology for demonstration. 62 refs.

  20. Treatment of spent NTA-based decontamination solutions

    Science.gov (United States)

    Pavlík, A.; Semelová, M.; John, J.; Černochová, K.; Šebesta, F.

    2006-01-01

    This study deals with potential treatment of spent NTA-containing decontamination solutions for final disposal. The method proposed is based on the degradation of organic substances followed by the separation of radionuclides. The influence of various parameters (pH value, irradiation time, temperature, catalyst amount, type and various combinations of catalysts) on photocatalytic degradation of NTA has been studied. Photo-Fenton reagent (Fe3+/H2O2) as a homogenous catalyst was found to be much more efficient than the TiO2-based heterogeneous catalyst Degussa P25. Under optimum conditions NTA in a simulant of a spent decontamination solution without or with hydrazine could be degraded within 5 or 9 hours, respectively. The study of sorption properties of a series of absorbers revealed that radiostrontium and radiosilver can be effectively removed from the simulant of a spent decontamination solution even in the presence of NTA, while total NTA degradation is necessary for effective radiocobalt separation.

  1. A portable miniature anechoic chamber

    Science.gov (United States)

    Lorthioir, Jack; Gavin, Paul

    The portable miniature anechoic chamber (PMAC), a low-cost alternative to a full-size anechoic chamber, is presented. The PMAC is a miniature, enclosed, RF-tight microwave antenna range, which approximates the performance of an indoor range over the C through Ku (G through J)-band frequencies. The small footprint, four by six feet, allows for ease of movement by one person to a test site, indoors or outdoors. The PMAC can be used at I (intermediate)-level to support the operational readiness (OR) requirements of the U.S. Army, Navy or Air Force. In conjunction with the antenna test equipment (ATE), and under TPS control, it can be used for performance verification, fault detection and fault isolation. A typical application using the PMAC in this operating mode is described.

  2. Compact portable electric power sources

    Energy Technology Data Exchange (ETDEWEB)

    Fry, D.N.; Holcomb, D.E.; Munro, J.K.; Oakes, L.C.; Matson, M.J.

    1997-02-01

    This report provides an overview of recent advances in portable electric power source (PEPS) technology and an assessment of emerging PEPS technologies that may meet US Special Operations Command`s (SOCOM) needs in the next 1--2- and 3--5-year time frames. The assessment was performed through a literature search and interviews with experts in various laboratories and companies. Nineteen PEPS technologies were reviewed and characterized as (1) PEPSs that meet SOCOM requirements; (2) PEPSs that could fulfill requirements for special field conditions and locations; (3) potentially high-payoff sources that require additional R and D; and (4) sources unlikely to meet present SOCOM requirements. 6 figs., 10 tabs.

  3. iPad portable genius

    CERN Document Server

    McFedries, Paul

    2013-01-01

    Make the most of your iPad with these savvy tips and techniques The iPad, iPad Air, and iPad mini are taking the world by storm. This no-nonsense guide covers everything you want to know to take full advantage of all your iPad has to offer. Along with necessary basics about the newest iPad; iPad Air, iPad mini; and iOS; it gives you smart; innovative ways to accomplish a variety of tasks and tips to help you maximize the convenience of your Apple digital lifestyle. More than 100 million iPads have been sold; and the number continues to growHip and practical; Portable Genius guides are packed

  4. Portable Userspace Virtual Filesystem Switch

    Directory of Open Access Journals (Sweden)

    Łukasz Faber

    2013-01-01

    Full Text Available Multiple different filesystems — including disk-based, network, distributed, abstract — arean integral part of every operating system. They are usually written as kernel modules and abstracted to the user via a virtual filesystem switch. In this paper we analyse the feasibility of reimplementing the virtual filesystem switch as a userspace daemon and applicability of this approach in real-life usage. Such reimplementation will require a way to virtualise processes behaviour related to filesystem operations. The problem is non-trivial, as we assume limited capabilities of the VFS switch implemented in userspace. We present a layered architecture comprising of a monitoring process, the VFS abstraction and real filesystem implementations. All working in userspace. Then, we evaluate this solution in four areas: portability, feasibility, usability and performance. Our results demonstrate possible gains in using the userspace-based approach with monolithic kernels, but also underline problems that are encountered in this approach.

  5. Decontamination Options for Drinking Water Contaminated with Bacillus anthracis Spores

    Energy Technology Data Exchange (ETDEWEB)

    Raber, E; Burklund, A

    2010-02-16

    Five parameters were evaluated with surrogates of Bacillus anthracis spores to determine effective decontamination options for use in a contaminated drinking water supply. The parameters were: (1) type of Bacillus spore surrogate (B. thuringiensis or B. atrophaeus); (2) spore concentration in suspension (10{sup 2} to 10{sup 6} spores/ml); (3) chemical characteristics of decontaminant [sodium dicholor-s-triazinetrione dihydrate (Dichlor), hydrogen peroxide, potassium peroxymonosulfate (Oxone), sodium hypochlorite, and VirkonS{reg_sign}]; (4) decontaminant concentration (0.01% to 5%); and (5) decontaminant exposure time (10 min to 24 hr). Results from 162 suspension tests with appropriate controls are reported. Hydrogen peroxide at a concentration of 5%, and Dichlor and sodium hypochlorite at a concentration of 2%, were effective at spore inactivation regardless of spore type tested, spore exposure time, or spore concentration evaluated. This is the first reported study of Dichlor as an effective decontaminant for B. anthracis spore surrogates. Dichlor's desirable characteristics of high oxidation potential, high level of free chlorine, and more neutral pH than that of other oxidizers evaluated appear to make it an excellent alternative. All three oxidizers were effective against B. atrophaeus spores in meeting EPA's biocide standard of greater than a 6 log kill after a 10-minute exposure time and at lower concentrations than typically reported for biocide use. Solutions of 5% VirkonS{reg_sign} and Oxone were less effective decontaminants than other options evaluated in this study and did not meet the EPA's efficacy standard for biocides. Differences in methods and procedures reported by other investigators make quantitative comparisons among studies difficult.

  6. Physicochemical characteristics of PFC surfactants for dry decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Oh, Won Jin; Lee, Chi Woo [Korea University, Seoul (Korea)

    2001-04-01

    Even the trace amount of the used nuclear fuels of high radioactivity are hazardous to the earth and humans. Perfluorocarbons and perfluorocarbon surfactants are emerging to be efficient chemicals in the dry decontamination process of the used fuels of high radioactivity. The theme was undertaken to increase the knowledge on perfluorocarbon surfactants to develop the perfluorocarbon system in the dry decontamination process in Korea. Several cationic and anionic pfc surfactants were synthesized. Effects of pfc surfactants on electrochemical etching of silicon were investigated to form porous silicons. Forces were measured between silicon surfaces and AFM tip in the absence and presence of pfc surfactants. 7 refs., 10 figs. (Author)

  7. Electron beam irradiation for biological decontamination of Spirulina platensis

    Energy Technology Data Exchange (ETDEWEB)

    Brasoveanu, Mirela [National Institute for Lasers, Plasma and Radiation Physics, Department of Electron Accelerators, 409 Atomistilor Street, P.O. Box MG-36, RO 76 900 Bucharest-Magurele (Romania)]. E-mail: mirela@infim.ro; Nemtanu, Monica [National Institute for Lasers, Plasma and Radiation Physics, Department of Electron Accelerators, 409 Atomistilor Street, P.O. Box MG-36, RO 76 900 Bucharest-Magurele (Romania); Minea, R. [National Institute for Lasers, Plasma and Radiation Physics, Department of Electron Accelerators, 409 Atomistilor Street, P.O. Box MG-36, RO 76 900 Bucharest-Magurele (Romania); Grecu, Maria Nicoleta [National Institute for Materials Physics, Bucharest-Magurele (Romania); Mazilu, Elena [Hofigal SA (Romania); Radulescu, Nora [Hofigal SA (Romania)

    2005-10-15

    The Cyanobacterium Spirulina is commercialized for its use in health foods and for therapeutic purposes due to its valuable constituents particularly proteins and vitamins. The aim of the paper is to study the Spirulina platensis behaviour when it is electron beam irradiated for biological decontamination. Microbial load, antioxidant activity, enzymatic inhibition, electron spin resonance (ESR) and UV-Vis spectra were measured for doses up to 80 kGy. The results were correlated with doses in order to find where decontamination is efficient, keeping the Spirulina qualities.

  8. Decontamination properties of bentonite in rats irradiated contaminated with radiocesium

    Energy Technology Data Exchange (ETDEWEB)

    Kossakowski, S.; Dziura, A. [National Veterinary Research Institute, Pulawy (Poland)

    1994-12-31

    Decontamination properties of bentonite were examined in rats irradiated with 154.5 mC/kg and contaminated with 13.83 kBq of Cs-137. The rats were fed a granulated LSM diet supplemented with 10% bentonite for 1, 3 and 5 days and were examined radiometrically for Cs-137 concentration in the small intestine, liver, kidneys, lung, spleen, heart, muscles, tongue, blood, brain, testicles and prostate. The findings revealed that the highest decontamination efficacy in the rats contaminated 1 and 5 days postirradiation was achieved after three-day administration of bentonite. (author). 16 refs, 2 tabs.

  9. A Method for Image Decontamination Based on Partial Differential Equation

    Directory of Open Access Journals (Sweden)

    Hou Junping

    2015-01-01

    Full Text Available This paper will introduce the method to apply partial differential equations for the decontamination processing of images. It will establish continuous partial differential mathematical models for image information and use specific solving methods to conduct decontamination processing to images during the process of solving partial differential equations, such as image noise reduction, image denoising and image segmentation. This paper will study the uniqueness of solution for the partial differential equations and the monotonicity that functional constrain has on multipliers by making analysis of the ROF model in the partial differential mathematical model.

  10. Economies of capacity use in decontamination of pig carcasses

    DEFF Research Database (Denmark)

    Jensen, Jørgen Dejgård; Lawson, Lartey Godwin; Lund, Mogens

    2013-01-01

    This article analyzes the economies of capacity use regarding hot water decontamination to reduce postslaughter risk of pathogens in meat, taking interfarm heterogeneities of Salmonella risk and costs of transportation into account, using Denmark as a case study. If risk reduction goals are stated...... at the processing plant level, then the exploitation of the favorable cost-effectiveness properties of hot water slaughtering requires fairly ambitious risk reduction goals and thus high use of decontamination capacity. If instead risk reduction goals are formulated for the sector as a whole, the cost...

  11. [Decontamination of continual cell lines spontaneously infected with mycoplasmas].

    Science.gov (United States)

    Machatková, M; Jurmanová, K; Snejdar, V

    1986-07-01

    The continual cell lines of bovine kidneys MDBK and AUBEK, and porcine kidneys RPD and IBRS, spontaneously infected with Mycoplasma arginini and Acholeplasma laidlawii, were decontaminated by the method of selective elimination. Two elimination procedures were modified to be used for the decontamination: one based on the reduction of infection by the light treatment of the cultures, the other based on the selection of mycoplasma-free cell population through cell clonation. On the basis of a long-continued control of the cell clones a methodical procedure of the preparation of mycoplasma-free cell lines was worked out.

  12. Electron beam irradiation for biological decontamination of Spirulina platensis

    Science.gov (United States)

    Brasoveanu, Mirela; Nemtanu, Monica; Minea, R.; Grecu, Maria Nicoleta; Mazilu, Elena; Radulescu, Nora

    2005-10-01

    The Cyanobacterium Spirulina is commercialized for its use in health foods and for therapeutic purposes due to its valuable constituents particularly proteins and vitamins. The aim of the paper is to study the Spirulina platensis behaviour when it is electron beam irradiated for biological decontamination. Microbial load, antioxidant activity, enzymatic inhibition, electron spin resonance (ESR) and UV-Vis spectra were measured for doses up to 80 kGy. The results were correlated with doses in order to find where decontamination is efficient, keeping the Spirulina qualities.

  13. Decontamination and Decommissioned Small Nuclear AIP Hybrid Systems Submarines

    Directory of Open Access Journals (Sweden)

    Guangya Liu

    2013-11-01

    Full Text Available Being equipped with small reactor AIP is the trend of conventional submarine power in 21st century as well as a real power revolution in conventional submarine. Thus, the quantity of small reactor AIP Submarines is on the increase, and its decommissioning and decontamination will also become a significant international issue. However, decommissioning the small reactor AIP submarines is not only a problem that appears beyond the lifetime of the small reactor nuclear devices, but the problem involving the entire process of design, construction, running and closure. In the paper, the problem is explored based on the conception and the feasible decommissioning and decontamination means are supplied to choose from.

  14. A mass casualty incident involving children and chemical decontamination.

    Science.gov (United States)

    Timm, Nathan; Reeves, Scott

    2007-01-01

    Mass casualty incidents involving contaminated children are a rare but ever-present possibility. In this article we outline one such event that resulted in 53 pediatric patients and 3 adults presenting to the emergency department of a children's hospital for decontamination and treatment. We pay special attention to the training that allowed this responses to occur. We also outline the institutional response with emphasis on incident command, communication, and resource utilization. Specific lessons learned are explored in detail. Finally, we set forth a series of recommendations to assist other institutions should they be called upon to care for and decontaminate pediatric patients.

  15. Concrete decontamination by Electro-Hydraulic Scabbling (EHS)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-11-01

    EHS is being developed for decontaminating concrete structures from radionuclides, organic substances, and hazardous metals. EHS involves the generation of powerful shock waves and intense cavitation by a strong pulsed electric discharge in a water layer at the concrete surface; high impulse pressure results in stresses which crack and peel off a concrete layer of controllable thickness. Scabbling produces contaminated debris of relatively small volume which can be easily removed, leaving clean bulk concrete. Objective of Phase I was to prove the technical feasibility of EH for controlled scabbling and decontamination of concrete. Phase I is complete.

  16. Mycotoxin Decontamination of Food: Cold Atmospheric Pressure Plasma versus "Classic" Decontamination.

    Science.gov (United States)

    Hojnik, Nataša; Cvelbar, Uroš; Tavčar-Kalcher, Gabrijela; Walsh, James L; Križaj, Igor

    2017-04-28

    Mycotoxins are secondary metabolites produced by several filamentous fungi, which frequently contaminate our food, and can result in human diseases affecting vital systems such as the nervous and immune systems. They can also trigger various forms of cancer. Intensive food production is contributing to incorrect handling, transport and storage of the food, resulting in increased levels of mycotoxin contamination. Mycotoxins are structurally very diverse molecules necessitating versatile food decontamination approaches, which are grouped into physical, chemical and biological techniques. In this review, a new and promising approach involving the use of cold atmospheric pressure plasma is considered, which may overcome multiple weaknesses associated with the classical methods. In addition to its mycotoxin destruction efficiency, cold atmospheric pressure plasma is cost effective, ecologically neutral and has a negligible effect on the quality of food products following treatment in comparison to classical methods.

  17. Definition of a concrete bio-decontamination process in nuclear substructures; Biodegradation de matrices cimentaires en vue de leur decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Jestin, A

    2005-05-15

    The decontamination of sub-structural materials represents a stake of high-importance because of the high volume generated. It is agreed then to propose efficient and effective processes. The process of bio-decontamination of the hydraulic binders leans on the mechanisms of biodegradation of concretes, phenomenon characterized in the 40's by an indirect attack of the material by acids stem from the microbial metabolism: sulphuric acid (produced by Thiobacillus), nitric acid (produced by Nitrosomonas and Nitrobacter) and organic acids (produced by fungi). The principle of the bio-decontamination process is to apply those micro-organisms on the surface of the contaminated material, in order to damage its surface and to retrieve the radionuclides. One of the multiple approaches of the process is the use of a bio-gel that makes possible the micro-organisms application. (author)

  18. Modelling of the hydrodynamic behaviour of a decontamination foam; Modelisation du comportement hydrodynamique d'une mousse de decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Faury, M.; Fournel, B. [CEA Cadarache, Dept. d' Entreposage et de Stockage des Dechets, 13 - Saint-Paul-lez-Durance (France)

    2001-07-01

    Decontamination of large components of nuclear power plants (refrigerants, vapor generators, effluents storage tanks...) produces an important volume of secondary effluents. The use of decontamination foams is an alternative allowing a significant diminution of this volume (about of a factor ten). The aim of this work is to propose models which could be applied by an industrialist in order to anticipate the behaviour of a foam flowing out in a component of any geometry and simplifying then the pre-study steps. (O.M.)

  19. Evaluating Performance Portability of OpenACC

    Energy Technology Data Exchange (ETDEWEB)

    Sabne, Amit J [ORNL; Sakdhnagool, Putt [ORNL; Lee, Seyong [ORNL; Vetter, Jeffrey S [ORNL

    2015-01-01

    Accelerator-based heterogeneous computing is gaining momentum in High Performance Computing arena. However, the increased complexity of the accelerator architectures demands more generic, high-level programming models. OpenACC is one such attempt to tackle the problem. While the abstraction endowed by OpenACC offers productivity, it raises questions on its portability. This paper evaluates the performance portability obtained by OpenACC on twelve OpenACC programs on NVIDIA CUDA, AMD GCN, and Intel MIC architectures. We study the effects of various compiler optimizations and OpenACC program settings on these architectures to provide insights into the achieved performance portability.

  20. Portable Tablets in Science Museum Learning

    DEFF Research Database (Denmark)

    Gronemann, Sigurd Trolle

    2016-01-01

    Despite the increasing use of portable tablets in learning, their impact has received little attention in research. In five different projects, this media-ethnographic and design-based analysis of the use of portable tablets as a learning resource in science museums investigates how young people......’s learning with portable tablets matches the intentions of the museums. By applying media and information literacy (MIL) components as analytical dimensions, a pattern of discrepancies between young people’s expectations, their actual learning and the museums’ approaches to framing such learning...

  1. Mac OS X Lion portable genius

    CERN Document Server

    Spivey, Dwight

    2012-01-01

    Two e-books, Mac OS X Lion Portable Genius and MacBook Pro Portable Genius, Third Edition, bundled in one package Books in the Portable Genius series provide readers with the most accessible, useful information possible, including plenty of tips and techniques for the most-used features in a product or software. These e-books will show you what you may not find out by just working with your MacBook Pro and OS X Lion. Genius icons present smart or innovative ways to do something, saving time and hassle. Easy-to-find information gives you the essentials plus insightful tips on how to navigate

  2. An Overview of Portable Distributed Techniques

    Directory of Open Access Journals (Sweden)

    Sanjay Bansal

    2010-05-01

    Full Text Available In this paper, we reviewed of several portable parallel programming paradigms for use in a distributed programming environment. The Techniques reviewed here are portable. These are mainly distributing computing using MPI pure java based, MPI native java based (JNI and PVM. We will discuss architecture and utilities of each technique based on our literature review. We explored these portable distributed techniques in four important characteristics scalability, fault tolerance, load balancing and performance. We have identified the various factors and issues for improving these four important characteristics.

  3. An Overview of Portable Distributed Techniques

    CERN Document Server

    Bansal, Sanjay

    2011-01-01

    In this paper, we reviewed of several portable parallel programming paradigms for use in a distributed programming environment. The Techniques reviewed here are portable. These are mainly distributing computing using MPI pure java based, MPI native java based (JNI) and PVM. We will discuss architecture and utilities of each technique based on our literature review. We explored these portable distributed techniques in four important characteristics scalability, fault tolerance, load balancing and performance. We have identified the various factors and issues for improving these four important characteristics.

  4. One of the First Portable Macs

    CERN Multimedia

    1989-01-01

    It was one of the first portable macs released. The Portable had many new advances in mobile computing : The display was crispy clear, and looked beautiful when used in daylight ; The Portable came with a Lead-acid gel/cell battery that could run a anywhere from 6 -12 hours ; It supported to internal hard drives, and an external one. The reaction to the laptop was weak because it was slow, it had no capacity for expansion, it weighed heavily, its price was expensive. It has been stayed 1 year and half on the market.

  5. Results of chemical decontamination of DOE`s uranium-enrichment scrap metal

    Energy Technology Data Exchange (ETDEWEB)

    Levesque, R.G.

    1997-02-01

    The CORPEX{reg_sign} Nuclear Decontamination Processes were used to decontaminate representative scrap metal specimens obtained from the existing scrap metal piles located at the Department of Energy (DOE) Portsmouth Gaseous Diffusion Plant (PORTS), Piketon, Ohio. In September 1995, under contract to Lockheed Martin Energy Systems, MELE Associates, Inc. performed the on-site decontamination demonstration. The decontamination demonstration proved that significant amounts of the existing DOE scrap metal can be decontaminated to levels where the scrap metal could be economically released by DOE for beneficial reuse. This simple and environmentally friendly process can be used as an alternative, or in addition to, smelting radiologically contaminated scrap metal.

  6. Portable Unit for Metabolic Analysis

    Science.gov (United States)

    Dietrich, Daniel L.; Pitch, Nancy D.; Lewis, Mark E.; Juergens, Jeffrey R.; Lichter, Michael J.; Stuk, Peter M.; Diedrick, Dale M.; Valentine, Russell W.; Pettegrew, Richard D.

    2007-01-01

    The Portable Unit for Metabolic Analysis (PUMA) is an instrument that measures several quantities indicative of human metabolic function. Specifically, this instrument makes time-resolved measurements of temperature, pressure, flow, and the partial pressures of oxygen and carbon dioxide in breath during both inhalation and exhalation. Portable instruments for measuring these quantities have been commercially available, but the response times of those instruments are too long to enable temporal resolution of phenomena on the time scales of human respiration cycles. In contrast, the response time of the PUMA is significantly shorter than characteristic times of human respiration phenomena, making it possible to analyze varying metabolic parameters, not only on sequential breath cycles but also at successive phases of inhalation and exhalation within the same breath cycle. In operation, the PUMA is positioned to sample breath near the subject s mouth. Commercial off-the-shelf sensors are used for three of the measurements: a miniature pressure transducer for pressure, a thermistor for temperature, and an ultrasonic sensor for flow. Sensors developed at Glenn Research Center are used for measuring the partial pressures of oxygen and carbon dioxide: The carbon dioxide sensor exploits the relatively strong absorption of infrared light by carbon dioxide. Light from an infrared source passes through the stream of inhaled or exhaled gas and is focused on an infrared- sensitive photodetector. The oxygen sensor exploits the effect of oxygen in quenching the fluorescence of ruthenium-doped organic molecules in a dye on the tip of an optical fiber. A blue laser diode is used to excite the fluorescence, and the optical fiber carries the fluorescent light to a photodiode, the temporal variation of the output of which bears a known relationship with the rate of quenching of fluorescence and, hence, with the partial pressure of oxygen. The outputs of the sensors are digitized

  7. Chemical decontamination of façade cracks

    Science.gov (United States)

    Etzold, Merlin A.; Landel, Julien R.; Dalziel, Stuart B.

    2016-11-01

    The problem of cleaning and decontamination of buildings arises in the context of chemical spillages, terrorist attacks, industrial applications and in day-to-day situations such as the removal of graffiti. A common feature of all buildings is the existence of cracks and fissures, which act as contaminant traps. This contribution reports experiments and modelling of the removal of a water-soluble contaminant from the bottom of an idealised V-shaped crack. The contaminant is dissolved in a polymer thickened droplet. The surface washing techniques commonly used in industrial decontamination induce a flow in the crack which is mostly controlled by the crack geometry. Rinsing with pure water is compared against the situation in which a neutralising chemical is present. The cleaning process is modelled by solving the time-dependent diffusion equation within the droplet coupled to the steady state advection-diffusion equation outside the droplet. This approach is similar to the work of Landel et al. on decontaminating plane surfaces beneath falling films. Our results indicate that the proposed model describes successfully the earlier stages of decontamination. In later stages the dissolution of the thickened matrix may contribute to the process.

  8. Chemical decontamination technical resources at Los Alamos National Laboratory (2008)

    Energy Technology Data Exchange (ETDEWEB)

    Moore, Murray E [Los Alamos National Laboratory

    2008-01-01

    This document supplies information resources for a person seeking to create planning or pre-planning documents for chemical decontamination operations. A building decontamination plan can be separated into four different sections: Pre-planning, Characterization, Decontamination (Initial response and also complete cleanup), and Clearance. Of the identified Los Alamos resources, they can be matched with these four sections: Pre-planning -- Dave Seidel, EO-EPP, Emergency Planning and Preparedness; David DeCroix and Bruce Letellier, D-3, Computational fluids modeling of structures; Murray E. Moore, RP-2, Aerosol sampling and ventilation engineering. Characterization (this can include development projects) -- Beth Perry, IAT-3, Nuclear Counterterrorism Response (SNIPER database); Fernando Garzon, MPA-11, Sensors and Electrochemical Devices (development); George Havrilla, C-CDE, Chemical Diagnostics and Engineering; Kristen McCabe, B-7, Biosecurity and Public Health. Decontamination -- Adam Stively, EO-ER, Emergency Response; Dina Matz, IHS-IP, Industrial hygiene; Don Hickmott, EES-6, Chemical cleanup. Clearance (validation) -- Larry Ticknor, CCS-6, Statistical Sciences.

  9. The Ultimate Hacker: SETI Signals May Need to Be Decontaminated

    Science.gov (United States)

    Carrigan, Richard A., Jr.

    2004-06-01

    Biological contamination from space is a remote but recognized possibility. SETI signals might also contain harmful information. Some argue that a SETI signal could not contaminate a terrestrial computer because the idiosyncratic computer logic and code constitute an impenetrable firewall. Suggestions are given below on how to probe these arguments and decontaminate SETI signals.

  10. Radiation decontamination of dry food ingredients and processing aids

    Energy Technology Data Exchange (ETDEWEB)

    Farkas, J.

    1984-01-01

    Radiation decontamination of dry ingredients, herbs and enzyme preparations is a technically feasible, economically viable and safe physical process. The procedure is direct, simple, requires no additives and is highly efficient. Its dose requirement is moderate. Radiation doses of 3-10 kGy (0.3-1 mrad) have proved sufficient to reduce the viable counts to a satisfactory level. Ionising radiations do not cause any significant rise in temperature. The flavour, texture or other important technological or sensory properties of most ingredients are not influenced at radiation doses necessary for satisfactory decontamination, and radiation obviates the chemical residue problem. The microflora surviving radiation decontamination of dry ingredients are more susceptible to subsequent antimicrobial treatments. Recontamination can be prevented as the product can be irradiated in its final packaging. Irradiation could be carried out in commercial containers and would result in considerable savings of energy and labour as compared to alternative decontamination techniques. Radiation processing of these commodities is an established technology in several countries and more clearances on irradiated foods are expected to be granted in the near future.

  11. Disinfectants used for environmental disinfection and new room decontamination technology.

    Science.gov (United States)

    Rutala, William A; Weber, David J

    2013-05-01

    Environmental contamination plays an important role in the transmission of several key health care-associated pathogens. Effective and thorough cleaning/disinfecting of the patient environment is essential. Room decontamination units (such as ultraviolet-C and hydrogen peroxide systems) aid in reducing environmental contamination after terminal room cleaning and disinfection.

  12. Use of selective digestive tract decontamination in European intensive cares

    DEFF Research Database (Denmark)

    Reis Miranda, D; Citerio, G; Perner, A

    2015-01-01

    BACKGROUND: Several studies have shown that the use of selective digestive tract decontamination (SDD) reduces mortality. However, fear for increasing multi drug resistance might prevent wide acceptance. A survey was performed among the units registered in the European Registry for Intensive Care...

  13. Ultrasonic decontamination of prototype fast breeder reactor fuel pins.

    Science.gov (United States)

    Kumar, Aniruddha; Bhatt, R B; Behere, P G; Afzal, Mohd

    2014-04-01

    Fuel pin decontamination is the process of removing particulates of radioactive material from its exterior surface. It is an important process step in nuclear fuel fabrication. It assumes more significance with plutonium bearing fuel known to be highly radio-toxic owing to its relatively longer biological half life and shorter radiological half life. Release of even minute quantity of plutonium oxide powder in the atmosphere during its handling can cause alarming air borne activity and may pose a severe health hazard to personnel working in the vicinity. Decontamination of fuel pins post pellet loading operation is thus mandatory before they are removed from the glove box for further processing and assembly. This paper describes the setting up of ultrasonic decontamination process, installed inside a custom built fume-hood in the production line, comprising of a cleaning tank with transducers, heaters, pin handling device and water filtration system and its application in cleaning of fuel pins for prototype fast breeder reactor. The cleaning process yielded a typical decontamination efficiency of more than 99%.

  14. Pulse lavage washing in decontamination of allografts improves safety.

    Science.gov (United States)

    Hirn, M; Laitinen, M; Vuento, R

    2003-01-01

    We analyzed the bacterial contamination rate of 140 femoral head allografts after rinsing the allografts in different decontamination solutions. Bacterial screening methods and cleansing effect of antibiotics (cefuroxime and rifampicin) and pulse lavage were compared. Swabbing and taking small pieces of bone for culture were the screening methods used. Both methods proved to be quite unreliable. Approximately one-fourth of the results were false negative. Culturing small pieces of bone gave the most accurate and reliable results and, therefore, can be recommended as a bacterial screening method. The use of antibiotics in allograft decontamination is controversial. In prophylactic use antibiotics include risks of allergic reactions and resistant development and our results in the present study show that antibiotics do not improve the decontamination any better than low-pressure pulse lavage with sterile saline solution. Therefore, pulse lavage with sterile saline solution can be recommended for allograft decontamination. Our results demonstrate that it decreases bacterial bioburden as effectively as the antibiotics without persisting the disadvantages.

  15. Fundamental study of cesium decontamination from soil by superconducting magnet

    Energy Technology Data Exchange (ETDEWEB)

    Igarashi, Susumu, E-mail: igarashi@qb.see.eng.osaka-u.ac.jp; Mishima, Fumihito; Akiyama, Yoko, E-mail: yoko-ak@see.eng.osaka-u.ac.jp; Nishijima, Shigehiro

    2013-11-15

    Highlights: •The method for the soil decontamination by the superconducting magnet is proposed. •Cesium ion can be absorbed by Prussian blue in potassium iodide wash fluid. •It is possible to recover Cs{sup +} ion-adsorbing Prussian blue with a high rate by HGMS. •It is expected that HGMS can be applied to the actual soil decontamination. -- Abstract: The radioactive substances have been spread out all over the surrounding area of Fukushima Daiichi Nuclear Power Plant caused by the accident in March 2011. Decontamination and volume reduction of radioactive substances, especially cesium ion, are desired issue. This study proposed a decontamination method of the soil by the magnetic separation using superconducting magnet. Cesium ion was adsorbed by Prussian blue in the potassium iodide solution. We succeeded in separating selectively the cesium ion-adsorbed Prussian blue out of the liquid phase by high gradient magnetic separation. High recovery ratio of the Prussian blue was achieved by this method.

  16. Pesticides water decontamination in oxygen-limited conditions.

    Science.gov (United States)

    Suciu, Nicoleta Alina; Ferrari, Federico; Vasileiadis, Sotirios; Merli, Annalisa; Capri, Ettore; Trevisan, Marco

    2013-01-01

    This study was undertaken to develop a laboratory bioreactor, with a functioning principle similar with that of biobed systems but working in oxygen-limited conditions, suitable for decontaminating wastewater mixtures with pesticides. The system is composed by two cylindrical plastic containers. The first one, where the pesticides solution is collected, is open, whereas the second one, where the biomass is disposed, is closed. The pesticides solution was pumped at the biomass surface and subsequently recollected and disposed in the first container. Four pesticides with different physical-chemical characteristics were tested. The results obtained showed a relatively good capacity of the developed prototype to decontaminate waste water containing the mixture of pesticides. The time of the experiment, the number of cycles that the solution made in the system and the environmental temperature have a significantly influence for the decontamination of acetochlor and chlorpyrifos whereas for the decontamination of terbuthylazine and metalaxyl no significant influence was observed. Even if the present prototype could represent a valid solution to manage the water pesticides residues in a farm and to increase the confidence of bystanders and residents, the practical difficulties when replacing the biomass could represent a limit of the system.

  17. Decontamination of tried-in orthodontic molar bands.

    Science.gov (United States)

    Fulford, M R; Ireland, A J; Main, B G

    2003-12-01

    Molar bands are commonly used to retain orthodontic attachments on posterior teeth and due to the variation in the size of such teeth, it is usually necessary to 'try in' several bands before the correct one is selected. A possible concern with re-using such bands is the lack of cross-infection control, even following autoclaving, due to the presence of one or more small bore lumen (the archwire and headgear tubes). The aim of this experiment was, therefore, to determine whether such bands could be successfully decontaminated so that they could be re-used without a cross-infection risk. Two hundred orthodontic molar bands that had previously been tried in patients' mouths, but not cemented into place, were tested. Each band was decontaminated using an enzymatic cleaner/disinfectant and then sterilized using either a downward displacement (n = 100) or a vacuum cycle autoclave (n = 100). Following autoclaving each band was inoculated into brain heart infusion culture broth and incubated at 37 degrees C for 5 days. None of the decontaminated bands exhibited growth after 5 days. It would appear that, using this methodology, there is little risk of a cross-infection hazard occurring with the re-use of previously tried-in and decontaminated molar bands.

  18. Selective digestive decontamination in patients in intensive care

    NARCIS (Netherlands)

    Bonten, MJM; Kullberg, BJ; Girbes, ARJ; Hoepelman, IM; Hustinx, W; van der Meer, JWM; Speelman, P; Stobberingh, EE; Verbrugh, HA; Verhoef, J; Zwaveling, JH

    2000-01-01

    Selective digestive decontamination (SDD) is the most extensively studied method for the prevention of infection in patients in intensive care units (ICUs). Despite 27 prospective randomized studies and six meta-analyses, routine use of SDD is still controversial. In this review, we summarize the av

  19. Legionella on board trains: effectiveness of environmental surveillance and decontamination

    Directory of Open Access Journals (Sweden)

    Quaranta Gianluigi

    2012-08-01

    Full Text Available Abstract Background Legionella pneumophila is increasingly recognised as a significant cause of sporadic and epidemic community-acquired and nosocomial pneumonia. Many studies describe the frequency and severity of Legionella spp. contamination in spa pools, natural pools, hotels and ships, but there is no study analysing the environmental monitoring of Legionella on board trains. The aims of the present study were to conduct periodic and precise environmental surveillance of Legionella spp. in water systems and water tanks that supply the toilet systems on trains, to assess the degree of contamination of such structures and to determine the effectiveness of decontamination. Methods A comparative pre-post ecological study was conducted from September 2006 to January 2011. A total of 1,245 water samples were collected from plumbing and toilet water tanks on passenger trains. The prevalence proportion of all positive samples was calculated. The unpaired t-test was performed to evaluate statistically significant differences between the mean load values before and after the decontamination procedures; statistical significance was set at p ≤ 0.05. Results In the pre-decontamination period, 58% of the water samples were positive for Legionella. Only Legionella pneumophila was identified: 55.84% were serogroup 1, 19.03% were serogroups 2–14 and 25.13% contained both serogroups. The mean bacterial load value was 2.14 × 103 CFU/L. During the post-decontamination period, 42.75% of water samples were positive for Legionella spp.; 98.76% were positive for Legionella pneumophila: 74.06% contained serogroup 1, 16.32% contained serogroups 2–14 and 9.62% contained both. The mean bacterial load in the post-decontamination period was 1.72 × 103 CFU/L. According to the t-test, there was a statistically significant decrease in total bacterial load until approximately one and a half year after beginning the decontamination programme (p

  20. Decontamination Processes for Restorative Operations and as a Precursor to Decommissioning: A Literature Review

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, J. L.; Divine, J. R.

    1981-05-01

    Pacific Northwest Laboratory (PNL) conducted an comprehensive literature review of actual reactor decontamination processes that are currently available. In general, any decontamination process should be based on the following criteria: effectiveness, efficiency, safety, and waste production. The information that was collected and analyzed has been divided into three major categories of decontamination: chemical, mechanical, and electrochemical. Chemical methods can be further classified as either low-concentration, singlestep processes or high-concentration, single- or multistep processes. Numerous chemical decontamination methods are detailed. Mechanical decontamination methods are usually restricted to the removal of a contaminated surface layer, whlch limits their versatility; several mechanical decontamination methods are described. Electrochemical decontamination. is both fast and easily controlled, and numerous processes that have been used in industry for many years are discussed. Information obtained from this work is tabulated in Appendix A for easy access, and a bibliography and a glossary have been provided.

  1. Development of portable fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Nakatou, K.; Sumi, S.; Nishizawa, N. [Sanyo Electric Co., Ltd., Osaka (Japan)

    1996-12-31

    Sanyo Electric has been concentrating on developing a marketable portable fuel cell using phosphoric acid fuel cells (PAFC). Due to the fact that this power source uses PAFC that operate at low temperature around 100{degrees} C, they are easier to handle compared to conventional fuel cells that operate at around 200{degrees} C , they can also be expected to provide extended reliable operation because corrosion of the electrode material and deterioration of the electrode catalyst are almost completely nonexistent. This power source is meant to be used independently and stored at room temperature. When it is started up, it generates electricity itself using its internal load to raise the temperature. As a result, the phosphoric acid (the electolyte) absorbs the reaction water when the temperature starts to be raised (around room temperature). At the same time the concentration and volume of the phosphoric acid changes, which may adversely affect the life time of the cell. We have studied means for starting, operating PAFC stack using methods that can simply evaluate changes in the concentration of the electrolyte in the stack with the aim of improving and extending cell life and report on them in this paper.

  2. Portable Microleak-Detection System

    Science.gov (United States)

    Rivers, H. Kevin; Sikora, Joseph G.; Sankaran, Sankara N.

    2007-01-01

    The figure schematically depicts a portable microleak-detection system that has been built especially for use in testing hydrogen tanks made of polymer-matrix composite materials. (As used here, microleak signifies a leak that is too small to be detectable by the simple soap-bubble technique.) The system can also be used to test for microleaks in tanks that are made of other materials and that contain gases other than hydrogen. Results of calibration tests have shown that measurement errors are less than 10 percent for leak rates ranging from 0.3 to 200 cm3/min. Like some other microleak-detection systems, this system includes a vacuum pump and associated plumbing for sampling the leaking gas, and a mass spectrometer for analyzing the molecular constituents of the gas. The system includes a flexible vacuum chamber that can be attached to the outer surface of a tank or other object of interest that is to be tested for leakage (hereafter denoted, simply, the test object). The gas used in a test can be the gas or vapor (e.g., hydrogen in the original application) to be contained by the test object. Alternatively, following common practice in leak testing, helium can be used as a test gas. In either case, the mass spectrometer can be used to verify that the gas measured by the system is the test gas rather than a different gas and, hence, that the leak is indeed from the test object.

  3. Portable basketball rim testing device

    Science.gov (United States)

    Abbott, W. Bruce; Davis, Karl C.

    1993-01-01

    A portable basketball rim rebound testing device 10 is illustrated in two preferred embodiments for testing the rebound or energy absorption characteristics of a basketball rim 12 and its accompanying support to determine likely rebound or energy absorption charcteristics of the system. The apparatus 10 includes a depending frame 28 having a C-clamp 36 for releasably rigidly connecting the frame to the basketball rim 12. A glide weight 60 is mounted on a guide rod 52 permitting the weight 60 to be dropped against a calibrated spring 56 held on an abutment surface on the rod to generate for deflecting the basketball rim and then rebounding the weight upwardly. A photosensor 66 is mounted on the depending frame 28 to sense passage of reflective surfaces 75 on the weight to thereby obtain sufficient data to enable a processing means 26 to calculate the rebound velocity and relate it to an energy absorption percentage rate of the rim system 12. A readout is provided to display the energy absorption percentage.

  4. Evaluation of a portable air purifier.

    OpenAIRE

    Lawrence, J.C.; Lilly, H. A.; Wilkins, M. D.

    1981-01-01

    A portable air purifier significantly reduced mal odour in a small room. If the atmosphere was deliberately contaminated with Serratia marcescens the unit rapidly removed this organism. However, if incorrectly sited, the purifier could disperse organisms into the atmosphere.

  5. Portable Remote Imaging Spectrometer (PRISM) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Develop an UV-NIR (350nm to 1050 nm) portable remote imaging spectrometer (PRISM) for flight on a variety of airborne platforms with high SNR and response...

  6. Portability of supplementary pension rights in Europe

    DEFF Research Database (Denmark)

    Guardiancich, Igor

    2015-01-01

    In its effort to guarantee the free movement of workers, the European Union devised an advanced system of coordination of social security rights. Since 1958, statutory pensions are being aggregated for workers moving across the Member States. However, until mid-2014, the portability of supplement......In its effort to guarantee the free movement of workers, the European Union devised an advanced system of coordination of social security rights. Since 1958, statutory pensions are being aggregated for workers moving across the Member States. However, until mid-2014, the portability...... a slowly recovering Europe. After nine years of negotiations, the EU has finally passed a Portability Directive, which is, however, a watered down version of the 2005 original proposal. Given such state of affairs, this study has three aims. First, it explains why portability of supplementary pensions...

  7. Fighting Ebola through Novel Spore Decontamination Technologies for the Military

    Directory of Open Access Journals (Sweden)

    Christopher J. Doona

    2015-08-01

    Full Text Available AbstractRecently, global public health organizations such as Doctors without Borders (MSF, the World Health Organization (WHO, Public Health Canada, National Institutes of Health (NIH, and the U.S. government developed and deployed Field Decontamination Kits (FDKs, a novel, lightweight, compact, reusable decontamination technology to sterilize Ebola-contaminated medical devices at remote clinical sites lacking infra-structure in crisis-stricken regions of West Africa (medical waste materials are placed in bags and burned. The basis for effectuating sterilization with FDKs is chlorine dioxide (ClO2 produced from a patented invention developed by researchers at the US Army – Natick Soldier RD&E Center (NSRDEC and commercialized as a dry mixed-chemical for bacterial spore decontamination. In fact, the NSRDEC research scientists developed an ensemble of ClO2 technologies designed for different applications in decontaminating fresh produce; food contact and handling surfaces; personal protective equipment; textiles used in clothing, uniforms, tents, and shelters; graywater recycling; airplanes; surgical instruments; and hard surfaces in latrines, laundries, and deployable medical facilities. These examples demonstrate the far-reaching impact, adaptability, and versatility of these innovative technologies. We present herein the unique attributes of NSRDEC’s novel decontamination technologies and a Case Study of the development of FDKs that were deployed in West Africa by international public health organizations to sterilize Ebola-contaminated medical equipment. FDKs use bacterial spores as indicators of sterility. We review the properties and structures of spores and the mechanisms of bacterial spore inactivation by ClO2. We also review mechanisms of bacterial spore inactivation by novel, emerging, and established nonthermal technologies for food preservation, such as high pressure processing, irradiation, cold plasma, and chemical sanitizers

  8. Development of the dry decontamination technique using plasma

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Yong Soo; Seo, Yong Dae; Lee, Dong Uk; Jeon, Sang Hwan; Jung, Young Suk [Hanyang University, Seoul (Korea)

    2001-04-01

    In order to develop an advanced dry decontamination method, dry decontamination technique using gaseous plasma is studied. Scopes of the research are 1) literature survey and case studies of the international R and D activities and industrial application, 2) contaminant characteristics analysis, 3) feasibility and applicability study of the unit techniques, 4) process development study on the plasma decontamination, 5) plasma diagnostics and quantitative analysis by QMS and OES, and 6) design of (microwave) plasma torch system. The major research results are as belows. The maximum etching rate of UO{sub 2} is achieved to be 0.8 {mu}m/min. under 300 deg C, 150 W CF{sub 4}/O{sub 2}/N{sub 2} r.f. plasma maintaining the optimum ratio of CF{sub 4}/O{sub 2} of four, and that of Co and Mo is 0.06 {mu}m/min. and 1.9 {mu}m/min., respectively, under 380 deg C, 220 W CF{sub 4}/O{sub 2} r.f. plasma. The optimum process for the dry decontamination of TRU, CP, and or FP nuclides, therefore, requires the optimum gas composition above 350 deg C and 220W power. It is also demonstrated that this optimum process can be extrapolated to atmospheric high power torch system. In conclusion, if plasma power and temperature increases with maintaining the optimum gas composition, this dry decontamination techniques must be definitely effective and efficient. 17 refs., 62 figs., 4 tabs. (Author)

  9. Nonacid meat decontamination technologies: model studies and commercial applications.

    Science.gov (United States)

    Sofos, J N; Smith, G C

    1998-11-10

    Increased consumer awareness and concern about microbial foodborne diseases has resulted in intensified efforts to reduce contamination of raw meat, as evidenced by new meat and poultry inspection regulations being implemented in the United States. In addition to requiring operation of meat and poultry slaughtering and processing plants under the principles of the hazard analysis critical control point (HACCP) system, the new regulations have established microbiological testing criteria for Escherichia coli and Salmonella, as a means of evaluating plant performance. These developments have renewed and intensified interest in the development and commercial application of meat and poultry decontamination procedures. Technologies developed and evaluated for decontamination include live animal cleaning/washing, chemical dehairing, carcass knife-trimming to remove physical contaminants, steam/hot water-vacuuming for spot-cleaning/decontamination of carcasses, spray washing/rinsing of carcasses with water of low or high pressures and temperatures or chemical solutions, and exposure of carcass sides to pressurized steam. Under appropriate conditions, the technologies applied to carcasses may reduce mean microbiological counts by approximately one-three log colony forming units (cfu)/cm2, and some of them have been approved and are employed in commercial applications (i.e., steam-vacuuming; carcass spray-washing with water, chlorine, organic acid or trisodium phosphate solutions; hot water deluging/spraying/rinsing, and pressurized steam). The contribution of these decontamination technologies to the enhancement of food safety will be determined over the long term, as surveillance data on microbial foodborne illness are collected. This review examines carcass decontamination technologies, other than organic acids, with emphasis placed on recent advances and commercial applications.

  10. Treatability studies for decontamination of Melton Valley Storage Tank supernate

    Energy Technology Data Exchange (ETDEWEB)

    Arnold, W.D.; Fowler, V.L.; Perona, J.J.; McTaggart, D.R.

    1992-08-01

    Liquid low-level waste, primarily nitric acid contaminated with radionuclides and minor concentrations of organics and heavy metals, is neutralized with sodium hydroxide, concentrated by evaporation, and stored for processing and disposal. The evaporator concentrate separates into sludge and supernate phases upon cooling. The supernate is 4 to 5 mol/L sodium nitrate contaminated with soluble radionuclides, principally {sup 137}Cs, {sup 90}Sr, and {sup 14}C, while the sludge consists of precipitated carbonates and hydroxides of metals and transuranic elements. Methods for treatment and disposal of this waste are being developed. In studies to determine the feasibility of removing {sup 137}Cs from the supernates before solidification campaigns, batch sorption measurements were made from four simulated supernate solutions with four different samples of potassium hexacyanocobalt ferrate (KCCF). Cesium decontamination factors of 1 to 8 were obtained with different KCCF batches from a highly-salted supernate at pH 13. Decontamination factors as high as 50 were measured from supernates with lower salt content and pH, in fact, the pH had a greater effect than the solution composition on the decontamination factors. The decontamination factors were highest after 1 to 2 d of mixing and decreased with longer mixing times due to decomposition of the KCCF in the alkaline solution. The decontamination factors decreased with settling time and were lower for the same total contact time (mixing + settling) for the longer mixing times, indicating more rapid KCCF decomposition during mixing than during settling. There was no stratification of cesium in the tubes as the KCCF decomposed.

  11. 46 CFR 195.11-30 - Portable tanks.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Portable tanks. 195.11-30 Section 195.11-30 Shipping... AND MISCELLANEOUS SYSTEMS AND EQUIPMENT Portable Vans and Tanks § 195.11-30 Portable tanks. (a) All portable tanks, whether hazardous or nonhazardous commodities, shall be loaded and stowed in...

  12. 49 CFR 180.603 - Qualification of portable tanks.

    Science.gov (United States)

    2010-10-01

    ... portable tanks. (d) A portable tank that also meets the definition of “container” in 49 CFR 450.3(a)(3... 49 Transportation 2 2010-10-01 2010-10-01 false Qualification of portable tanks. 180.603 Section... QUALIFICATION AND MAINTENANCE OF PACKAGINGS Qualification and Maintenance of Portable Tanks §...

  13. Decontamination Systems Information and Research Program

    Energy Technology Data Exchange (ETDEWEB)

    Cook, Echol E; Beatty, Tia Maria

    1998-07-01

    The following paragraphs comprise the research efforts during the second quarter of 1998 (April 1 - June 30.) These tasks have been granted a continuation until the end of August 1998. This report represents the last technical quarterly report deliverable for the WVU Cooperative Agreement - Decontamination Systems Information and Research Program. Final draft technical reports will be the next submission. During this period, work was completed on the Injection and Circulation of Potable Water Through PVDs on Task 1.6 - Pilot Scale Demonstration of TCE Flushing Through PVDs at the DOE/RMI Extrusion Plant. The data has been evaluated and representative graphs are presented. The plot of Cumulative Injected Volume vs. Cumulative Week Time show the ability to consistently inject through the two center PVDs at a rate of approximately ten (10) gallons per hour. This injection rate was achieved under a static head that varied from five (5) feet to three (3) feet. The plot of Extracted Flow Rate vs. Cumulative Week Time compares the extraction rate with and without the injection of water. The injection operation was continuous for eight hour periods while the extraction operation was executed over a pulsing schedule. Extraction rates as high as forty-five (45) gallons per hour were achieved in conjunction with injection (a 350% increase over no injection.) The retrieved TCE in the liquid phase varied to a considerable degree depending on the pulsing scheme, indicating a significant amount of stripping (volatilization) took place during the extraction process. A field experiment was conducted to confirm this. A liquid sample was obtained using the same vacuum system used in the pad operation and a second liquid sample was taken by a bailer. Analyzation of TCE concentration showed 99.5% volatilization when the vacuum system was used for extraction. This was also confirmed by data from the air monitoring program which indicated that 92%-99% of the retrieved TCE was being

  14. Forensic Analysis of the Sony Playstation Portable

    Science.gov (United States)

    Conrad, Scott; Rodriguez, Carlos; Marberry, Chris; Craiger, Philip

    The Sony PlayStation Portable (PSP) is a popular portable gaming device with features such as wireless Internet access and image, music and movie playback. As with most systems built around a processor and storage, the PSP can be used for purposes other than it was originally intended - legal as well as illegal. This paper discusses the features of the PSP browser and suggests best practices for extracting digital evidence.

  15. Development of a Portable Sensitive Equipment Decontamination System. Volume 1: Commercial Candidates Materials Evaluation (Chemical Agent Studies)

    Science.gov (United States)

    2010-05-01

    wiping tests were conducted with: 3MScotch-Britc2011 3MScotch-Brite2021N Activated Carbon Felt Activated Carbon Fiber Procter and Gamble Swiffer...Cloths, manufactured by Proctor and Gamble and purchased locally. • Pledge® Grab-It Wipes: Dry wipes cut from commercial Pledge® Grab-It disposable...registered trademark of Proctor and Gamble . Cincinnati. OH. Pledged is a registered trademark of S.C. Johnson & Son, Racine, WI. CutexS is a

  16. Comparison of Four Skin Decontamination Procedures Using Reactive Skin Decontamination Lotion (RSDL) Following Cutaneous VX Exposure in Guinea Pigs

    Science.gov (United States)

    2016-01-01

    decontaminated with RSDL. RSDL was applied with an applicator made by stapling one fourth of an RSDL sponge pad (25 mm x 50 mm) to a wooden tongue ...RSDL was applied by swiping the applicator across the exposure site ten times in a head-to-tail direction with steady pressure on the exposure site

  17. Portable apparatus for separating sample and detecting target analytes

    Energy Technology Data Exchange (ETDEWEB)

    Renzi, Ronald F. (Tracy, CA); Wally, Karl (Lafayette, CA); Crocker, Robert W. (Fremont, CA); Stamps, James F. (Livermore, CA); Griffiths; Stewart K. ,(Livermore, CA); Fruetel, Julia A. (Livermore, CA); Horn, Brent A. (Roy, UT); Shokair, Isaac R. (Livermore, CA); Yee, Daniel D. (Dublin, CA); VanderNoot, Victoria A. (Pleasanton, CA); Wiedenman, Boyd J. (Aiken, SC); West, Jason A. A. (Pleasanton, CA); Ferko, Scott M. (Livermore, CA)

    2008-11-18

    Portable devices and methods for determining the presence of a target analyte using a portable device are provided. The portable device is preferably hand-held. A sample is injected to the portable device. A microfluidic separation is performed within the portable device and at least one separated component detected by a detection module within the portable device, in embodiments of the invention. A target analyte is identified, based on the separated component, and the presence of the target analyte is indicated on an output interface of the portable device, in accordance with embodiments of the invention.

  18. Decontamination of human and rabbit skin experimentally contaminated with 99mTc radionuclide using the active components of "Shudhika"-a skin decontamination kit.

    Science.gov (United States)

    Rana, Sudha; Dutta, Mita; Soni, Nakshe L; Chopra, Mahendra K; Kumar, Vinod; Goel, Rajeev; Bhatnagar, Aseem; Sultana, Sarwat; Sharma, Rakesh Kumar

    2012-04-01

    Radioactive contamination can occur as a result of accidental or intentional release of radioactive materials (RM) into the environment. RM may deposit on clothing, skin, or hair. Decontamination of contaminated persons should be done as soon as possible to minimize the deleterious health effects of radiation. The goal of this study was to evaluate the decontamination efficiency (for residual contaminant) of the active components of "Shudhika," an indigenously developed skin decontamination kit. The study kit is for external radioactive decontamination of intact skin. Decontamination efficiency was evaluated on the skin surface of rabbit (n = 6) and human volunteers (n = 13). 99mTc sodium pertechnetate (200-250 μCi) was used as the radio-contaminant. Skin surface area (5 × 5 cm2) of thoracic abdominal region of the rabbit and the forearm and the palm of human volunteers were used for the study. Decontamination was performed by using cotton swabs soaked with chemical decontamination agents of the kit. Decontamination efficiency (% of the contaminant removed) was calculated for each component of the study. Overall effectiveness of the kit was calculated to be 85% ± 5% in animal and 92% ± 3% in human skin surfaces. Running water and liquid soap with water was able to decontaminate volunteers' hand and animal skin up to 70% ± 5%. Chemical decontamination agents were applied only for trace residues (30% ± 5%). Efficiency of all the kit components was found up to be 20% ± 3% (animal) and 28% ± 2 (human), respectively. Residual contamination after final decontamination attempt for both the models was observed to be 12% ± 3% and 5% ± 2%. After 24 and 48 hours of the decontamination procedure, skin was found to be normal (no redness, erythema and edema were observed). Decontaminants of the study kit were effective in removal of localized radioactive skin contamination when water is ineffective for further decontamination. By using the chemical decontaminants of

  19. Evaluation of the PhysioTel™ Digital M11 cardiovascular telemetry implant in socially housed cynomolgus monkeys up to 16weeks after surgery.

    Science.gov (United States)

    Andersen, Ninette K; Meyer, Olivier; Bradley, Alys; Dragsted, Nils; Lassen, Anders B; Sjögren, Ingrid; Larsen, Julie M; Harvey, Warren; Bator, Rastislav; Milne, Aileen

    2017-09-01

    The novel PhysioTel™ Digital M11 telemetry implant was evaluated in socially housed monkeys with respect to both safety pharmacological cardiovascular (arterial blood pressure (BP), heart rate (HR) and electrocardiogram (ECG)) and toxicological (clinical pathology and histopathology) endpoints. Telemetry and clinical pathology data were obtained repeatedly up to 16weeks after surgery in four female cynomolgus monkeys, followed by necropsy. Due to postsurgical complications, one spare animal was included and only toxicological endpoints from the affected (fifth animal) were reported. Continuous telemetry recordings were conducted at periods without dosing and after ascending doses of moxifloxacin (0, 10, 30, 100mg/kg) and L-NAME (0, 0.1, 1, 10mg/kg). Additionally, a retrospective power analysis was conducted based on baseline M11 implant data from 32 other animals. During periods without dosing, the cardiovascular endpoints were stable over time and within normal ranges. Moxifloxacin and L-NAME elicited the expected pharmacological responses with dose-dependent increase in QTca (8, 17, 22ms) and BP (mean BP: 12, 21, 34mmHg), respectively. Expected intravascular and tissue reactions were observed at the sites of the BP catheter and the transmitter. Signs of infection (localised to the transmitter implantation site with associated systemic effects) was noted in the fifth animal. No systemic pathologies were seen in any animals. Power analysis (80% power) indicated that the minimal differences which can be detected in a parallel group design (n=6) are 7mmHg (mean BP), 16bpm (HR), 12ms (QTca). The M11 implant provided stable, high quality ECG and BP data for a duration covering the length of sub-chronic repeated dose toxicity studies without important impact on toxicological endpoints. Adequate power in order to elucidate major treatment-related cardiovascular effects was demonstrated. However to avoid post-surgical complications the implantation procedures should be

  20. Study on the Decontamination Methodology for the Refurbishment of Spent Fuel Dry Processing Facility

    Energy Technology Data Exchange (ETDEWEB)

    Won, H. J.; Jung, C. H.; Moon, J. K.; Byambatsere, Baigalmaa; Park, G. I.; Lee, D. Y.; Lee, J. W.; Song, K. C.

    2010-01-15

    As the increase of the operation age of the domestic high radiation facilities such as IMEF, PIEF and DFDF, the necessity of decontamination and refurbishment of hot cells in these facilities is also increased. In the near future, the possibilities of refurbishment of hot cells in compliance with the new regulations, the reuse of hot cells for the other purposes and the decommissioning of the facilities also exist. The following contents were studied. 1) State of the art on the decontamination technologies on the spent fuel dry processing facility - Case study on the decontamination and refurbishment of hot cells in the foreign countries. - Understanding of radioactive contamination characteristics of spent fuel powder treatment equipment operated under the high radiation field of the spent fuel dry processing facility. - Evaluation of applicable decontamination technologies 2) Comparative tests of the candidate decontamination technology - Preparation of the surrogate test specimens and derivation of gel decontamination condition - Decontamination tests and comparison with light ablation method 3) Establishment of decontamination methodology for the refurbishment of hot cells of the spent fuel dry processing facility - Derivation of required equipment for the hot cell decontamination - Establishment of decontamination methodologies on the contaminated equipment

  1. Assessing cost and effectiveness of radiation decontamination in Fukushima Prefecture, Japan.

    Science.gov (United States)

    Yasutaka, Tetsuo; Naito, Wataru

    2016-01-01

    Despite the enormous cost of radiation decontamination in Fukushima Prefecture, it is not clear what levels of reduction in external radiation exposure are possible in the Special Decontamination Area, the Intensive Contamination Survey Areas and the whole of Fukushima. The objective of this study was to evaluate the cost and effectiveness of radiation decontamination in Fukushima Prefecture in its entirety. Using a geographic information system, we calculated the costs of removal, storage containers, transport, and temporary and interim storage facilities as well as the reduction in air dose rate for a cumulative external exposure for 9000 1 km × 1 km mesh units incorporating 51 municipalities. The decontamination cost for the basic scenario, for which forested areas within 20 m of habitation areas were decontaminated, was JPY2.53-5.12 trillion; the resulting reduction in annual external dose was about 2500 person-Sv. The transport, storage, and administrative costs of decontamination waste and removed soil reached JPY1.55-2.12 trillion under this scenario. Although implementing decontamination of all forested areas provides some major reductions in the external radiation dose for the average inhabitant, decontamination costs could potentially exceed JPY16 trillion. These results indicate that technologies for reducing the volume of decontamination waste and removed soil should be considered to reduce storage costs and that further discussions about forest decontamination policies are needed.

  2. Fighting Ebola with novel spore decontamination technologies for the military.

    Science.gov (United States)

    Doona, Christopher J; Feeherry, Florence E; Kustin, Kenneth; Olinger, Gene G; Setlow, Peter; Malkin, Alexander J; Leighton, Terrance

    2015-01-01

    Recently, global public health organizations such as Doctors without Borders (MSF), the World Health Organization (WHO), Public Health Canada, National Institutes of Health (NIH), and the U.S. government developed and deployed Field Decontamination Kits (FDKs), a novel, lightweight, compact, reusable decontamination technology to sterilize Ebola-contaminated medical devices at remote clinical sites lacking infra-structure in crisis-stricken regions of West Africa (medical waste materials are placed in bags and burned). The basis for effectuating sterilization with FDKs is chlorine dioxide (ClO2) produced from a patented invention developed by researchers at the US Army Natick Soldier RD&E Center (NSRDEC) and commercialized as a dry mixed-chemical for bacterial spore decontamination. In fact, the NSRDEC research scientists developed an ensemble of ClO2 technologies designed for different applications in decontaminating fresh produce; food contact and handling surfaces; personal protective equipment; textiles used in clothing, uniforms, tents, and shelters; graywater recycling; airplanes; surgical instruments; and hard surfaces in latrines, laundries, and deployable medical facilities. These examples demonstrate the far-reaching impact, adaptability, and versatility of these innovative technologies. We present herein the unique attributes of NSRDEC's novel decontamination technologies and a Case Study of the development of FDKs that were deployed in West Africa by international public health organizations to sterilize Ebola-contaminated medical equipment. FDKs use bacterial spores as indicators of sterility. We review the properties and structures of spores and the mechanisms of bacterial spore inactivation by ClO2. We also review mechanisms of bacterial spore inactivation by novel, emerging, and established non-thermal technologies for food preservation, such as high pressure processing, irradiation, cold plasma, and chemical sanitizers, using an array of Bacillus

  3. Fighting Ebola with novel spore decontamination technologies for the military

    Science.gov (United States)

    Doona, Christopher J.; Feeherry, Florence E.; Kustin, Kenneth; Olinger, Gene G.; Setlow, Peter; Malkin, Alexander J.; Leighton, Terrance

    2015-01-01

    Recently, global public health organizations such as Doctors without Borders (MSF), the World Health Organization (WHO), Public Health Canada, National Institutes of Health (NIH), and the U.S. government developed and deployed Field Decontamination Kits (FDKs), a novel, lightweight, compact, reusable decontamination technology to sterilize Ebola-contaminated medical devices at remote clinical sites lacking infra-structure in crisis-stricken regions of West Africa (medical waste materials are placed in bags and burned). The basis for effectuating sterilization with FDKs is chlorine dioxide (ClO2) produced from a patented invention developed by researchers at the US Army Natick Soldier RD&E Center (NSRDEC) and commercialized as a dry mixed-chemical for bacterial spore decontamination. In fact, the NSRDEC research scientists developed an ensemble of ClO2 technologies designed for different applications in decontaminating fresh produce; food contact and handling surfaces; personal protective equipment; textiles used in clothing, uniforms, tents, and shelters; graywater recycling; airplanes; surgical instruments; and hard surfaces in latrines, laundries, and deployable medical facilities. These examples demonstrate the far-reaching impact, adaptability, and versatility of these innovative technologies. We present herein the unique attributes of NSRDEC’s novel decontamination technologies and a Case Study of the development of FDKs that were deployed in West Africa by international public health organizations to sterilize Ebola-contaminated medical equipment. FDKs use bacterial spores as indicators of sterility. We review the properties and structures of spores and the mechanisms of bacterial spore inactivation by ClO2. We also review mechanisms of bacterial spore inactivation by novel, emerging, and established non-thermal technologies for food preservation, such as high pressure processing, irradiation, cold plasma, and chemical sanitizers, using an array of Bacillus

  4. The impact of skin decontamination on the time window for effective treatment of percutaneous VX exposure.

    Science.gov (United States)

    Joosen, M J A; van den Berg, R M; de Jong, A L; van der Schans, M J; Noort, D; Langenberg, J P

    2017-04-01

    The main goal of the present study was to obtain insight into depot formation and penetration following percutaneous VX poisoning, in order to identify an appropriate decontamination window that can enhance or support medical countermeasures. The study was executed in two phases, using the hairless guinea pig as an animal model. In the first phase the effect of various decontamination regimens on levels of free VX in skin and plasma were studied as well as on blood cholinesterase levels. Animals were exposed to 0.5 mg/kg VX and were not decontaminated (control), decontaminated with RSDL once at 15 or 90 min after exposure or three times at 15, 25 and 35 (10-min interval) or 15, 45 and 75 min after exposure (30-min interval). There was no significant effect of any of the decontamination regimens on the 6-h survival rate of the animals. However, all animals that had been decontaminated 15 min after exposure, showed a survival rate of more than 90%, compared to 50-60% in animals that were not decontaminated or decontaminated at 90 min after exposure. In the second phase of the study, hairless guinea pigs were exposed to 1 mg/kg VX on the shoulder, followed either by decontamination with RSDL (10 min interval), conventional treatment on indication of clinical signs or a combination thereof. It appeared that a thorough, repeated decontamination alone could not save the majority of the animals. A 100% survival rate was observed in the group that received a combination of decontamination and treatment. In conclusion, the effects of VX exposure could be influenced by various RSDL decontamination regimens. The results in freely moving animals showed that skin decontamination, although not fully effective in removing all VX from the skin and skin depot is crucial to support pharmacological intervention.

  5. Decontamination of rat and human skin experimentally contaminated with (99m)Tc, (201)Tl and (131)I radionuclides using "Dermadecon" - a skin decontamination kit: an efficacy study.

    Science.gov (United States)

    Nishad, Dhruv Kumar; Bhalla, Supriya; Khanna, Kushagra; Sharma, Braj Gaurav; Rawat, Harish Singh; Mittal, Gaurav; Bhatnagar, Aseem

    2017-05-03

    Radioactive skin contamination is one of the most likely risks which occurs after accidental or occupational radiological accidents apart from internal contamination. In such cases where the radioactive contamination has occurred, the person who is contaminated should be decontaminated as early as possible to reduce the damaging health effects of radiation. In the present study, the decontamination efficiency of a developed skin decontamination kit "dermadecon" has been evaluated in animal models and human subjects using gamma scintigraphy. Decontamination efficiency (percentage of the radioactive contaminant removed) was calculated for each radioactive isotope of the study and compared with control where general washing procedure was followed using liquid and soap. The effectiveness of the kit was calculated in animal model with respect to (99m)Tc-sodium-pertechnetate ((99m)TcO(4-)), (201)TlCl and (131)I and was found 92.84 ± 4.9%, 91.18 ± 3.23% and 94.67 ± 2.92%, respectively. Whereas, in case of human skin, the decontamination efficiency for (99m)TcO(4-) was observed to be 95.00 ± 3.21%. On the basis of findings from the study, it can be concluded that the decontamination agents of the used skin decontamination kit are effective for removal of localized radioactive contaminants from skin, as compared with normal decontamination using soap and water.

  6. Cefuroxime, rifampicin and pulse lavage in decontamination of allograft bone.

    Science.gov (United States)

    Hirn, M; Laitinen, M; Pirkkalainen, S; Vuento, R

    2004-03-01

    The risk of bacterial infection through allogenic bone transplantation is one of the major problems facing tissue banks. Different screening methods and decontamination procedures are being used to achieve a safe surgical result. The purpose of this study was to investigate the contamination rate in fresh frozen bone allografts after treating them with different decontamination methods. The allografts were contaminated by rubbing on the operating theatre floor for 60 min, after which they were rinsed either with sterile physiological saline, cefuroxime or rifampicin solution or they were washed with low-pressure pulse lavage of sterile physiological saline. Our findings show that low-pressure pulse lavage with sterile saline solution is very effective in removing bacteria from bone allograft, when compared with the antibiotic solutions tested.

  7. Biofilm mediated decontamination of pollutants from the environment

    Directory of Open Access Journals (Sweden)

    Arindam Mitra

    2016-01-01

    Full Text Available In this review, we highlight beneficial use of microbial biofilms in remediation of environmental pollutants by bioremediation. Bioremediation is an environment friendly, cost effective, sustainable technology that utilizes microbes to decontaminate and degrade a wide variety of pollutants into less harmful products. Relative to free-floating planktonic cells, microbes existing in biofilm mode are advantageous for bioremediation because of greater tolerance to pollutants, environmental stress and ability to degrade varied harsh pollutants via diverse catabolic pathways. In biofilm mode, microbes are immobilized in a self-synthesized matrix which offers protection from stress, contaminants and predatory protozoa. Contaminants ranging from heavy metals, petroleum, explosives, pesticides have been remediated using microbial consortia of biofilms. In the industry, biofilm based bioremediation is used to decontaminate polluted soil and groundwater. Here we discuss conventional and newer strategies utilizing biofilms in environmental remediation.

  8. Physico-Chemical Dynamics of Nanoparticle Formation during Laser Decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, M.D.

    2005-06-01

    Laser-ablation based decontamination is a new and effective approach for simultaneous removal and characterization of contaminants from surfaces (e.g., building interior and exterior walls, ground floors, etc.). The scientific objectives of this research are to: (1) characterize particulate matter generated during the laser-ablation based decontamination, (2) develop a technique for simultaneous cleaning and spectroscopic verification, and (3) develop an empirical model for predicting particle generation for the size range from 10 nm to tens of micrometers. This research project provides fundamental data obtained through a systematic study on the particle generation mechanism, and also provides a working model for prediction of particle generation such that an effective operational strategy can be devised to facilitate worker protection.

  9. Decontamination and Decommissioning activities photobriefing book FY 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-04-01

    The Decontamination and Decommissioning (D and D) Program at Argonne National Laboratory-East (ANL-E) is dedicated to the safe and cost effective D{ampersand}D of surplus nuclear facilities. There is currently a backlog of more than 7,000 contaminated US Department of Energy facilities nationwide. Added to this are 110 licensed commercial nuclear power reactors operated by utilities learning to cope with deregulation and an aging infrastructure that supports the commercial nuclear power industry, as well as medical and other uses of radioactive materials. With this volume it becomes easy to understand the importance of addressing the unique issues and objectives associated with the D{ampersand}D of surplus nuclear facilities. This photobriefing book summarizes the decontamination and decommissioning projects and activities either completed or continuing at the ANL-E site during the year.

  10. A Nanosecond Pulsed Plasma Brush for Surface Decontamination

    Science.gov (United States)

    Neuber, Johanna; Malik, Muhammad; Song, Shutong; Jiang, Chunqi

    2015-11-01

    This work optimizes a non-thermal, atmospheric pressure plasma brush for surface decontamination. The generated plasma plumes with a maximum length of 2 cm are arranged in a 5 cm long, brush-like array. The plasma was generated in ambient air with plasma chamber at a rate varying between 1 to 7 SLPM. Optimization of the cold plasma brush for surface decontamination was tested in a study of the plasma inactivation of two common pathogens, Staphylococcus aureus and Acinetobacter baumannii. Laminate surfaces inoculated with over-night cultured bacteria were subject to the plasma treatment for varying water concentrations in He, flow rates and discharge voltages. It was found that increasing the water content of the feed gas greatly enhanced the bactericidal effect. Emission spectroscopy was performed to identify the reactive plasma species that contribute to this variation. Additional affiliation: Frank Reidy Research Center for Bioelectrics

  11. Decontamination of Radionuclides from Concrete During and After Thermal Treatment

    Energy Technology Data Exchange (ETDEWEB)

    Bazant, Z.P.

    1998-09-15

    The objective was to clarify from the theoretical viewpoint the mechanical, diffusional, thermodynamic and electromagnetic aspects of the decontaminations problem, by means of developing a powerful computational model to evaluate the effect of a very rapid heating regime on the on the contaminated concrete walls or slabs. The practical objective was to assess the feasibility of the microwave heating scheme envisaged and determine its suitable parameters such as power and duration. This objective was complementary to, but separate from, the chemical and nuclear aspects of long-time processes that led to the contamination and various conceivable alternative methods of decontamination which were investigated by Dr. Brian Spalding of Oak Ridge National Laboratory, with whom the start-up phase of this project was coordinated.

  12. Biophysical Evaluation of Food Decontamination Effects on Tissue and Bacteria

    DEFF Research Database (Denmark)

    Andersen, Ann Zahle; Duelund, Lars; Brewer, Jonathan

    2011-01-01

    Traditionally, the effects and efficiency of food surface decontamination processes, such as chlorine washing, radiation, or heating, have been evaluated by sensoric analysis and colony-forming unit (CFU) counts of surface swabs or carcass rinses. These methods suffice when determining probable...... employ differential scanning calorimetry, second harmonics generation imaging microscopy, two-photon fluorescence microscopy, and green fluorescence protein-expressing bacteria and compare our results with those obtained by traditional methods of food quality and safety evaluations. Our results show...

  13. Decontamination effectiveness of bentonite after a single administration of radiocesium

    Energy Technology Data Exchange (ETDEWEB)

    Kossakowski, S.; Dziura, A. [National Veterinary Research Institute, Pulawy (Poland)

    1992-12-31

    Decontamination effectiveness of bentonite was investigated in male Wistar rats contaminated intragastrically with Cs 137. The contaminated animals were fed a granulated LSM diet with 10% addition of bentonite for 1, 3 and 5 days after the contamination. The results revealed that rats fed bentonite showed a significant decrease in the radioactivity in examined organs and tissues as early as one day after the contamination, which was intensified with the feeding period. (author). 28 refs, 1 tab.

  14. Radiation survey and decontamination of cape Arza from depleted uranium

    Directory of Open Access Journals (Sweden)

    Vukotić Perko

    2003-01-01

    Full Text Available In the action of NATO A-10 airplanes in 1999, the cape Arza, Serbia and Montenegro was contaminated by depleted uranium. The clean-up operations were undertaken at the site, and 242 uranium projectiles and their 49 larger fragments were removed from the cape. That is about 85% of the total number of projectiles by which Arza was contaminated. Here are described details of the applied procedures and results of the soil radioactivity measurements after decontamination.

  15. Uranium Enrichment: Analysis of Decontamination and Decommissioning Scenarios

    Science.gov (United States)

    1991-11-01

    from a September 1991 report entitled Preliminary Cost Estimate Decontamination & Decommissioning of the Gaseous Diffusion Plants , prepared for DOE by...DOE) three aging uranium enrichment plants . These plants are located in Oak Ridge, Tennessee; Paducah , Kentucky; and Portsmouth, Ohio. On October 16... Diffusion Plants Assessment of Costs for Remedial Actions. This report was prepared for DOE by Martin Marietta Energy Systems, DOE’s management and

  16. Recommendations and Proposed Strategic Plan: Water Sector Decontamination Priorities

    Science.gov (United States)

    2008-10-01

    representing the GCC and SCC on this working group, we would like to thank you for the opportunity to serve as leaders of this esteemed group of professionals...revolving fund-type initiative, self insurance, regional pooling, stratification of funding based on risk) Provide utilities with a resource to...SECTOR DECONTAMINATION ISSUES − Residential uses (e.g., toilet, washing, showering, cooling, pet consumption, cooking) − Business uses (e.g., with

  17. DECONTAMINATION/DESTRUCTION TECHNOLOGY DEMONSTRATION FOR ORGANICS IN TRANSURANIC WASTE

    Energy Technology Data Exchange (ETDEWEB)

    Chris Jones; Javier Del Campo; Patrick Nevins; Stuart Legg

    2002-08-01

    The United States Department of Energy's Savannah River Site has approximately 5000 55-gallon drums of {sup 238}Pu contaminated waste in interim storage. These may not be shipped to WIPP in TRUPACT-II containers due to the high rate of hydrogen production resulting from the radiolysis of the organic content of the drums. In order to circumvent this problem, the {sup 238}Pu needs to be separated from the organics--either by mineralization of the latter or by decontamination by a chemical separation. We have conducted ''cold'' optimization trials and surrogate tests in which a combination of a mediated electrochemical oxidation process (SILVER II{trademark}) and ultrasonic mixing have been used to decontaminate the surrogate waste materials. The surrogate wastes were impregnated with copper oxalate for plutonium dioxide. Our process combines both mineralization of reactive components (such cellulose, rubber, and oil) and surface decontamination of less reactive materials such as polyethylene, polystyrene and polyvinylchloride. By using this combination of SILVER II and ultrasonic mixing, we have achieved 100% current efficiency for the destruction of the reactive components. We have demonstrated that: The degree of decontamination achieved would be adequate to meet both WIPP waste acceptance criteria and TRUPACT II packaging and shipping requirements; The system can maintain near absolute containment of the surrogate radionuclides; Only minimal pre-treatment (coarse shredding) and minimal waste sorting are required; The system requires minimal off gas control processes and monitoring instrumentation; The laboratory trials have developed information that can be used for scale-up purposes; The process does not produce dioxins and furans; Disposal routes for secondary process arisings have already been demonstrated in other programs. Based on the results from Phase 1, the recommendation is to proceed to Phase 2 and use the equipment at Savannah

  18. Dental unit water lines decontamination with the aid of nanotechnology

    Directory of Open Access Journals (Sweden)

    Rashmi Paramashivaiah

    2016-01-01

    Conclusions: Biofilm formation in DUWLs is inevitable with the subsequent release of part of microbiota into the otherwise sterile dental settings. These consequences can be quite serious on clinicians and dental patients. Though conventional measures in water decontamination have been partly successful, the quest for more foolproof methods has led to the use of latest technology, i.e., nanotechnology. The most practical option has to be chosen based on the ease of their usage.

  19. Dental unit water lines decontamination with the aid of nanotechnology

    OpenAIRE

    Rashmi Paramashivaiah; M. L. V. Prabhuji; Roopalakshmi Narayanan

    2016-01-01

    Aim: This article reviews the issue of dental unit waterline (DUWL) contamination which affects all the clinical and hospital settings. The contaminating microorganisms commonly isolated from these settings and the most pathogenic among them have serious consequences. Over the years several measures are inculcated for decontamination of water, their advantages and shortcomings have been addressed. Options using nanotechnology which are available in the market are described briefly. Materi...

  20. DECONTAMINATION/DESTRUCTION TECHNOLOGY DEMONSTRATION FOR ORGANICS IN TRANSURANIC WASTE

    Energy Technology Data Exchange (ETDEWEB)

    Chris Jones; Javier Del Campo; Patrick Nevins; Stuart Legg

    2002-08-01

    The United States Department of Energy's Savannah River Site has approximately 5000 55-gallon drums of {sup 238}Pu contaminated waste in interim storage. These may not be shipped to WIPP in TRUPACT-II containers due to the high rate of hydrogen production resulting from the radiolysis of the organic content of the drums. In order to circumvent this problem, the {sup 238}Pu needs to be separated from the organics--either by mineralization of the latter or by decontamination by a chemical separation. We have conducted ''cold'' optimization trials and surrogate tests in which a combination of a mediated electrochemical oxidation process (SILVER II{trademark}) and ultrasonic mixing have been used to decontaminate the surrogate waste materials. The surrogate wastes were impregnated with copper oxalate for plutonium dioxide. Our process combines both mineralization of reactive components (such cellulose, rubber, and oil) and surface decontamination of less reactive materials such as polyethylene, polystyrene and polyvinylchloride. By using this combination of SILVER II and ultrasonic mixing, we have achieved 100% current efficiency for the destruction of the reactive components. We have demonstrated that: The degree of decontamination achieved would be adequate to meet both WIPP waste acceptance criteria and TRUPACT II packaging and shipping requirements; The system can maintain near absolute containment of the surrogate radionuclides; Only minimal pre-treatment (coarse shredding) and minimal waste sorting are required; The system requires minimal off gas control processes and monitoring instrumentation; The laboratory trials have developed information that can be used for scale-up purposes; The process does not produce dioxins and furans; Disposal routes for secondary process arisings have already been demonstrated in other programs. Based on the results from Phase 1, the recommendation is to proceed to Phase 2 and use the equipment at Savannah

  1. Application of a novel decontamination process using gaseous ozone

    Energy Technology Data Exchange (ETDEWEB)

    Moat, J.; Shone, J.; Upton, M. [Manchester Univ., School of Medecine, Manchester (United Kingdom). Medical Microbiology, Translation Medicine; Cargill, J. [Old Medical School, Leeds (United Kingdom). Dept. of Microbiology

    2009-08-15

    Hospital surfaces that are touched regularly by staff carry bacterial spores and pathogens. Environmental disinfection of health care facilities is an important aspect of infection control. This paper presented a recent innovation aimed at improving hospital hygiene and decontamination of laboratory equipment. The vapour- and gas-based treatment was developed to penetrate rooms or soft furnishings and reach places inaccessible by conventional approaches. Surfaces seeded with a range of vegetative cells and spores of bacteria of clinical relevance were decontaminated using the ozone-based treatment. The efficiency of the approach for room sanitization was also evaluated. A quenching agent was used to rapidly reduce ozone concentrations to safe levels allowing treatment times of less than 1 h for most of the organisms tested. Bacteria was seeded onto agar plates and solid surfaces. Reductions in bacterial load of greater than 3 log values were then recorded for a number of organisms including Escherichia coli and methicillin-resistant Staphylococcus aureus. Application of the process in a 30 m{sup 3} room showed similar reductions in viable counts for these organisms and for Clostridium difficile spores. It was concluded that ozone-based decontamination of healthcare environments could prove to be a highly cost-effective intervention. 35 refs., 1 tab., 3 figs.

  2. Decontamination Methods Used for Dental Burs – A Comparative Study

    Science.gov (United States)

    Hugar, Deepa; Hugar, Santosh; Ranjan, Shashi; Kadani, Megha

    2014-01-01

    Aims and Objectives: Infection control and modes of sterilizations are the key factors to avoid cross transmission of infection in the field of dentistry. Transmission of disease or infection is noted with improper sterilization of reused instruments. Dental burs are the most important tool in any endodontic or conservative procedures of teeth involving tooth contouring, restorative filling procedures and endodontic procedures. Hence, the present study is undertaken to assess the efficacy of different methods of sterilization or decontamination which are routinely used in dental clinics. Materials and Methods: For the present study 96 round diamond burs were selected and divided into 6 groups. These burs were used for the access cavity preparation to get contamination and subjected for bacteriological culture. After getting base line date burs were subjected to manual scrubbing, hot air oven, glass bead sterilizer, ultrasonic cleaner and autoclave to get post decontamination data. Results: The study revealed that mean colony forming units/ml of Streptococcus mutans decreased maximum for autoclave with 80% reduction, for Lactobacilli 76% reduction and for Candida albicans maximum reduction seen for glass bead sterilizer with 74%. Conclusion: Findings of our study revealed that none of the methods used were found to be absolutely efficacious in the decontamination of dental burs. However, among the experimental groups used in the present study, autoclave was found to be the relatively best method. PMID:25121062

  3. Decontamination and decommissioning of the Mayaguez (Puerto Rico) facility

    Energy Technology Data Exchange (ETDEWEB)

    Jackson, P.K.; Freemerman, R.L. [Bechtel National, Inc., Oak Ridge, TN (United States)

    1989-11-01

    On February 6, 1987 the US Department of Energy (DOE) awarded the final phase of the decontamination and decommissioning of the nuclear and reactor facilities at the Center for Energy and Environmental Research (CEER), in Mayaguez, Puerto Rico. Bechtel National, Inc., was made the decontamination and decommissioning (D and D) contractor. The goal of the project was to enable DOE to proceed with release of the CEER facility for use by the University of Puerto Rico, who was the operator. This presentation describes that project and lesson learned during its progress. The CEER facility was established in 1957 as the Puerto Rico Nuclear Center, a part of the Atoms for Peace Program. It was a nuclear training and research institution with emphasis on the needs of Latin America. It originally consisted of a 1-megawatt Materials Testing Reactor (MTR), support facilities and research laboratories. After eleven years of operation the MTR was shutdown and defueled. A 2-megawatt TRIGA reactor was installed in 1972 and operated until 1976, when it woo was shutdown. Other radioactive facilities at the center included a 10-watt homogeneous L-77 training reactor, a natural uranium graphite-moderated subcritical assembly, a 200KV particle accelerator, and a 15,000 Ci Co-60 irradiation facility. Support facilities included radiochemistry laboratories, counting rooms and two hot cells. As the emphasis shifted to non-nuclear energy technology a name change resulted in the CEER designation, and plans were started for the decontamination and decommissioning effort.

  4. Atmospheric Pressure Plasma Jet for Chem/Bio Warfare Decontamination

    Science.gov (United States)

    Herrmann, Hans W.; Henins, Ivars; Park, Jaeyoung; Selwyn, Gary S.

    1999-11-01

    Atmospheric Pressure Plasma Jet (APPJ) technology may provide a much needed method of CBW decontamination which, unlike traditional decon methods, is dry and nondestructive to sensitive equipment and materials. The APPJ discharge uses a high-flow feedgas consisting primarily of an inert carrier gas, such as He, and a small amount of a reactive additive, such as O2, which flows between capacitively-coupled electrodes powered at 13.56 MHz. The plasma generates highly reactive metastable and atomic species of oxygen which are then directed onto a contaminated surface. The reactive effluent of the APPJ has been shown to effectively neutralize VX nerve agent as well as simulants for anthrax and mustard blister agent. Research efforts are now being directed towards reducing He consumption and increasing the allowable stand-off distance. Recent results demonstrate that by replacing the O2 reactive additive with CO2, ozone formation is greatly reduced. This has the result of extending the lifetime of atomic oxygen by an order of magnitude or more. A recirculating APP Decon Chamber which combines heat, vacuum, forced convection and reactivity is currently being developed for enhanced decontamination of sensitive equipment. Several techniques are also being evaluated for use in an APP Decon Jet for decontamination of items which cannot be placed inside a chamber.

  5. Personnel decontamination and preventive skin care; Personendekontamination und Hautprophylaxe

    Energy Technology Data Exchange (ETDEWEB)

    Henning, Klaus; Gojowczyk, Peter [AKA Kunz GmbH, Waldenbuch (Germany)

    2010-07-15

    Skin contamination arises from contact with contaminated aqueous solutions and from transmission of radioactively contaminated dirt particles. As long as the surface of the skin is neither inflamed nor showing any lesions, normally only a limited part of the top layer (epidermis), i.e. the upper layers of the stratum corneum, is contaminated. The intact horny layer has a barrier function protecting against the penetration of chemicals and dirt particles. The horny layer can be damaged by water, solvents, alkaline substances, and acids. In general, it is safe to say that the horny layer acts as a natural barrier to the penetration of liquid and particulate impurities into lower layers of the skin. As long as the horny layer is intact and free from lesions, the risk of incorporation can be considered low. When decontaminating and cleansing the skin, also in daily skin cleansing, care must be taken to prevent the acid protective layer and the horny layer from being compromised. Daily cleansing and cleansing for decontamination must be carried out with a mild, weakly acidic detergent. In addition, prevention should be achieved daily by applying a non-greasy skin lotion to protect the skin. Following a systematic regular regimen in skin cleansing and preventive skin care as well as a specific approach in skin decontamination and cleansing will avoid damage to the skin and remove any contamination incurred. This approach comprises a three-pronged concept, namely skin protection, cleansing and care. (orig.)

  6. Decontamination of mass casualties--re-evaluating existing dogma.

    Science.gov (United States)

    Levitin, Howard W; Siegelson, Henry J; Dickinson, Stanley; Halpern, Pinchas; Haraguchi, Yoshikura; Nocera, Anthony; Turineck, David

    2003-01-01

    The events of 11 September 2001 became the catalyst for many to shift their disaster preparedness efforts towards mass-casualty incidents. Emergency responders, healthcare workers, emergency managers, and public health officials worldwide are being tasked to improve their readiness by acquiring equipment, providing training and implementing policy, especially in the area of mass-casualty decontamination. Accomplishing each of these tasks requires good information, which is lacking. Management of the incident scene and the approach to victim care varies throughout the world and is based more on dogma than scientific data. In order to plan effectively for and to manage a chemical, mass-casualty event, we must critically assess the criteria upon which we base our response. This paper reviews current standards surrounding the response to a release of hazardous materials that results in massive numbers of exposed human survivors. In addition, a significant effort is made to prepare an international perspective on this response. Preparations for the 24-hour threat of exposure of a community to hazardous material are a community responsibility for first-responders and the hospital. Preparations for a mass-casualty event related to a terrorist attack are a governmental responsibility. Reshaping response protocols and decontamination needs on the differences between vapor and liquid chemical threats can enable local responders to effectively manage a chemical attack resulting in mass casualties. Ensuring that hospitals have adequate resources and training to mount an effective decontamination response in a rapid manner is essential.

  7. Cold Atmospheric Plasma Technology for Decontamination of Space Equipment

    Science.gov (United States)

    Thomas, Hubertus; Rettberg, Petra; Shimizu, Tetsuji; Thoma, Markus; Morfill, Gregor; Zimmermann, Julia; Müller, Meike; Semenov, Igor

    2016-07-01

    Cold atmospheric plasma (CAP) technology is very fast and effective in inactivation of all kinds of pathogens. It is used in hygiene and especially in medicine, since the plasma treatment can be applied to sensitive surfaces, like skin, too. In a first study to use CAP for the decontamination of space equipment we could show its potential as a quite promising alternative to the standard "dry heat" and H2O2 methods [Shimizu et al. Planetary and Space Science, 90, 60-71. (2014)]. In a follow-on study we continue the investigations to reach high application level of the technology. First, we redesign the actual setup to a plasma-gas circulation system, increasing the effectivity of inactivation and the sustainability. Additionally, we want to learn more about the plasma chemistry processes involved in the inactivation. Therefore, we perform detailed plasma and gas measurements and compare them to numerical simulations. The latter will finally be used to scale the decontamination system to sizes useful also for larger space equipment. Typical materials relevant for space equipment will be tested and investigated on surface material changes due to the plasma treatment. Additionally, it is planned to use electronic boards and compare their functionality before and after the CAP expose. We will give an overview on the status of the plasma decontamination project funded by the Bavarian Ministry of Economics.

  8. Irradiation as a decontamination processing for rice paper sheet

    Energy Technology Data Exchange (ETDEWEB)

    Araujo, Michel M.; Thomaz, Fernanda S.; Fanaro, Gustavo B.; Duarte, Renato C.; Aquino, Simone; Villavicencio, Anna Lucia C.H. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)]. E-mail: villavic@ipen.br; Correa, Benedito [Universidade de Sao Paulo USP, SP (Brazil). Inst. de Ciencias Biomedicas. Dept. de Micologia]. E-mail: correabe@usp.br

    2007-07-01

    Starch is one of the most important plant products to man. The major sources of this compound for man's use are the cereals, but roots and tubers are also important. The starch industry comes in recent years growing and perfecting it self, leading to the necessity products with specific characteristics that take care the requirements of the market, it makes possible through processing raw material, still seldom explored. Rice paper sheet is an edible product derived from potatoes and rice, being commonly used to cover cakes, pies, and sweets in confectioner's shop. A microbiological control is necessary to give a high quality and to guarantee the security of this food. Irradiation would be a safe alternative as a decontamination method without adverse effects on the physical properties in the final products. The aim of this study was to investigate the best dose used as a decontamination method as well as discover the most prevalent fungi found in this product and changes on physical properties. Samples of rice paper sheet were irradiated with 2.5, 5.0 and 10.0 kGy using a {sup 60}Co irradiator. Irradiation appeared as a safe alternative as a decontamination method without adverse effects on the physical properties in the final products. (author)

  9. Decontamination of dental implant surface in peri-implantitis treatment: a literature review

    OpenAIRE

    Mellado Valero, Ana; Buitrago Vera, Pedro José; Solá Ruiz, María Fernanda; Ferrer García, Juan Carlos

    2013-01-01

    Etiological treatment of peri-implantitis aims to reduce the bacterial load within the peri-implant pocket and decontaminate the implant surface in order to promote osseointegration. The aim of this literature review was to evaluate the efficacy of different methods of implant surface decontamination. A search was conducted using the PubMed (Medline) database, which identified 36 articles including in vivo and in vitro studies, and reviews of different decontamination systems (chemical, mecha...

  10. Compatibility and Decontamination of High-Density Polyethylene Exposed to Sulfur Mustard

    Science.gov (United States)

    2014-05-01

    and taken through the entire decontamination procedure. ***For coupons 11–20, the water temperature was ~65 oC when added. In all subsequent trials...the water temperature was ~ 95 oC. NA, not applicable. 11 Table 3. Decontamination Data–Pretreated Coupons Coupon Name and Number...COMPATIBILITY AND DECONTAMINATION OF HIGH-DENSITY POLYETHYLENE EXPOSED TO SULFUR MUSTARD ECBC-TR-1235

  11. EDF/CIDEN - ONECTRA: PWR decontamination; EDF/CIDEN - ONECTRA: assainissement REP

    Energy Technology Data Exchange (ETDEWEB)

    Fayolle, P. [EDFICIDEN, 35-37, rue Louis Guerin - B.P. 21212, 69611 Villeurbanne Cedex (France); Orcel, H. [ONECTRA, ZA les Tomples BP45, 26701 Pierrelatte Cedex (France); Wertz, L. [ONECTRA, Le Britannia, Allee C, 20 Bd Eugene Deruelle, 69432 Lyon Cedex 03 (France)

    2010-07-01

    In the context of PWR circuit renewal (expected in 2011) and their decontamination, an analysis of data coming from cartography and on site decontamination measurements as well as from premise modelling by means of the PANTHERE radioprotection code, is presented. Several French PWRs have been studied. After a presentation of code principles and operation, the authors discuss the radiological context of a workstation, and give an assessment of the annual dose associated with maintenance operations with or without decontamination

  12. Military display market segment: wearable and portable

    Science.gov (United States)

    Desjardins, Daniel D.; Hopper, Darrel G.

    2003-09-01

    The military display market (MDM) is analyzed in terms of one of its segments, wearable and portable displays. Wearable and portable displays are those embedded in gear worn or carried by warfighters. Categories include hand-mobile (direct-view and monocular/binocular), palm-held, head/helmet-mounted, body-strapped, knee-attached, lap-born, neck-lanyard, and pocket/backpack-stowed. Some 62 fielded and developmental display sizes are identified in this wearable/portable MDM segment. Parameters requiring special consideration, such as weight, luminance ranges, light emission, viewing angles, and chromaticity coordinates, are summarized and compared. Ruggedized commercial versus commercial off-the-shelf designs are contrasted; and a number of custom displays are also found in this MDM category. Display sizes having aggregate quantities of 5,000 units or greater or having 2 or more program applications are identified. Wearable and portable displays are also analyzed by technology (LCD, LED, CRT, OLED and plasma). The technical specifications and program history of several high-profile military programs are discussed to provide a systems context for some representative displays and their function. As of August 2002 our defense-wide military display market study has documented 438,882 total display units distributed across 1,163 display sizes and 438 weapon systems. Wearable and portable displays account for 202,593 displays (46% of total DoD) yet comprise just 62 sizes (5% of total DoD) in 120 weapons systems (27% of total DoD). Some 66% of these wearable and portable applications involve low information content displays comprising just a few characters in one color; however, there is an accelerating trend towards higher information content units capable of showing changeable graphics, color and video.

  13. A mobile and portable trusted computing platform

    Directory of Open Access Journals (Sweden)

    Nepal Surya

    2011-01-01

    Full Text Available Abstract The mechanism of establishing trust in a computing platform is tightly coupled with the characteristics of a specific machine. This limits the portability and mobility of trust as demanded by many emerging applications that go beyond the organizational boundaries. In order to address this problem, we propose a mobile and portable trusted computing platform in a form of a USB device. First, we describe the design and implementation of the hardware and software architectures of the device. We then demonstrate the capabilities of the proposed device by developing a trusted application.

  14. Decontamination of B. globigii spores from drinking water infrastructure using disinfectants

    Data.gov (United States)

    U.S. Environmental Protection Agency — Decontamination of Bacillus spores adhered to common drinking water infrastructure surfaces was evaluated using a variety of disinfectants. Corroded iron and...

  15. Water decontamination of chemical skin/eye splashes: a critical review.

    Science.gov (United States)

    Hall, Alan H; Maibach, Howard I

    2006-01-01

    Skin/eye chemical splashes are a significant workplace problem. Initial water decontamination is usually recommended, but there are few well-conducted experimental animal and human studies of efficacy. An extensive review of the literature and other available information sources was performed to define the scope of the problem and critically review the evidence for water decontamination efficacy. Although water decontamination can decrease the severity of chemical skin/eye burns, it cannot completely prevent them. An ideal replacement decontamination solution would be sterile, nontoxic, chelating, polyvalent, amphoteric, and slightly hypertonic to retard skin or corneal penetration of the chemical.

  16. RSDL decontamination of human skin contaminated with the nerve agent VX.

    Science.gov (United States)

    Thors, L; Lindberg, S; Johansson, S; Koch, B; Koch, M; Hägglund, L; Bucht, A

    2017-03-05

    Dermal exposure to low volatile organophosphorus compounds (OPC) may lead to penetration through the skin and uptake in the blood circulation. Skin decontamination of toxic OPCs, such as pesticides and chemical warfare nerve agents, might therefore be crucial for mitigating the systemic toxicity following dermal exposure. Reactive skin decontamination lotion (RSDL) has been shown to reduce toxic effects in animals dermally exposed to the nerve agent VX. In the present study, an in vitro flow-through diffusion cell was utilized to evaluate the efficacy of RSDL for decontamination of VX exposed to human epidermis. In particular, the impact of timing in the initiation of decontamination and agent dilution in water was studied. The impact of the lipophilic properties of VX in the RSDL decontamination was additionally addressed by comparing chemical degradation in RSDL and decontamination efficacy between the VX and the hydrophilic OPC triethyl phosphonoacetate (TEPA). The epidermal membrane was exposed to 20, 75 or 90% OPC diluted in deionized water and the decontamination was initiated 5, 10, 30, 60 or 120min post-exposure. Early decontamination of VX with RSDL, initiated 5-10min after skin exposure, was very effective. Delayed decontamination initiated 30-60min post-exposure was less effective but still the amount of penetrated agent was significantly reduced, while further delayed start of decontamination to 120min resulted in very low efficacy. Comparing RSDL decontamination of VX with that of TEPA showed that the decontamination efficacy at high agent concentrations was higher for VX. The degradation mechanism of VX and TEPA during decontamination was dissected by (31)P NMR spectroscopy of the OPCs following reactions with RSDL and its three nucleophile components. The degradation rate was clearly associated with the high pH of the specific solution investigated; i.e. increased pH resulted in a more rapid degradation. In addition, the solubility of the OPC in RSDL

  17. Decontamination and decommissioning technology tree and the current status of the technologies

    Energy Technology Data Exchange (ETDEWEB)

    Oh, Won Zin; Won, H.J.; Kim, G.N.; Lee, K.W.; Chol, W.K.; Jung, C.H.; Kim, C.J.; Kim, S.H.; Kwon, S.O.; Chung, C.M

    2001-03-01

    A technology tree diagram was developed on the basis of the necessary technologies applicable to the decontamination and decommissioning of nuclear facilities. The technology tree diagram is consist of 6 main areas such as characterization, decontamination, decommissioning and remote technology, radwaste management, site restoration, and decommissioning plan and engineering. Characterization is divided into 4 regions such as sampling and data collection, general characterization, chemical analysis and radiological analysis. Decontamination is also divided into 4 regions such as chemical decontamination, mechanical decontamination, the other decontamination technologies and new decontamination technologies. Decommissioning and remote technology area is divided into 4 regions such as cutting techniques, decommissioning technologies, new developing technologies and remote technologies. Radwaste management area is divided into 5 regions such as solid waste treatment, sludge treatment, liquid waste treatment, gas waste treatment and thermal treatment. Site restoration area is divided into 3 regions such as the evaluation of site contamination, soil decontamination and ground water decontamination. Finally, permission, decommissioning process, cost evaluation, quality assurance and the estimation of radionuclide inventory were mentioned in the decommissioning plan and engineering area. The estimated items for each technology are applicable domestic D and D facilities, D and D problem area and contamination/requirement, classification of D and D technology, similar technology, principle and overview of technology, status, science technology needs, implementation needs, reference and contact point.

  18. 48 CFR 1837.170 - Pension portability.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Pension portability. 1837.170 Section 1837.170 Federal Acquisition Regulations System NATIONAL AERONAUTICS AND SPACE ADMINISTRATION SPECIAL CATEGORIES OF CONTRACTING SERVICE CONTRACTING Service Contracts-General 1837.170...

  19. Portable Data Logger for Photovoltaic Panels

    Science.gov (United States)

    Cole, S. W.

    1983-01-01

    Instrument measures rapidly changing knee of V-I curve with extra care. Portable data logger runs on own batteries. Includes microcomputer, which controls voltage-, current-measurement increment, and solid state memory, which stores data until transferred to EPROM module. Data logger is light, compact and easily caried to remote field locations.

  20. Portable Power And Digital-Communication Units

    Science.gov (United States)

    Levin, Richard R.; Henry, Paul K.; Rosenberg, Leigh S.

    1992-01-01

    Conceptual network of electronic-equipment modules provides electrical power and digital radio communications at multiple sites not served by cables. System includes central communication unit and portable units powered by solar photovoltaic arrays. Useful to serve equipment that must be set up quickly at remote sites or buildings that cannot be modified to provide cable connections.

  1. Selection of Power Sources for Portable Applications

    NARCIS (Netherlands)

    Flipsen, S.F.J.

    2009-01-01

    New power sources emerge very quickly. Implementation of hybrid power sources for portable electronics depends on the knowledge of industrial designers. For now this group has little understanding of fuel cells and especially fuel-cell hybrids. This slows down implementation and increases the chance

  2. Variable-speed, portable routing skate

    Science.gov (United States)

    Pesch, W. A.

    1967-01-01

    Lightweight, portable, variable-speed routing skate is used on heavy metal subassemblies which are impractical to move to a stationary machine. The assembly, consisting of the housing with rollers, router, and driving mechanism with transmission, weighs about forty pounds. Both speed and depth of cut are adjustable.

  3. A microcontroller-based portable electrocardiograph recorder.

    Science.gov (United States)

    Segura-Juárez, José J; Cuesta-Frau, David; Samblas-Pena, Luis; Aboy, Mateo

    2004-09-01

    We describe a low cost portable Holter design that can be implemented with off-the-shelf components. The recorder is battery powered and includes a graphical display and keyboard. The recorder is capable of acquiring up to 48 hours of continuous electrocardiogram data at a sample rate of up to 250 Hz.

  4. Comparison of selected skin decontaminant products and regimens against VX in domestic swine.

    Science.gov (United States)

    Bjarnason, S; Mikler, J; Hill, I; Tenn, C; Garrett, M; Caddy, N; Sawyer, T W

    2008-03-01

    An anesthetized domestic swine model was used to compare the efficacy and cross-contamination potential of selected skin decontaminant products and regimens against the chemical warfare agent, VX. Animals topically exposed to 2x, 3x or 5x LD(50) VX showed typical signs of organophosphate nerve agent poisoning, including miosis, salivation, mastication, dysrhythmias, and respiratory distress prior to death. Animals were exposed to 5x LD(50) VX and then decontaminated 45 min later with the reactive skin decontamination lotion (RSDL), Fuller's earth (FE), 0.5% hypochlorite, or soapy water. Survival was 100% when the reactive skin decontamination lotion or FE was utilized, although 50% of Fuller's earth-decontaminated animals exhibited serious signs of VX poisoning. Decontamination of VX-treated animals with 0.5% hypochlorite was less effective but also increased survival. Soapy water was ineffective in preventing lethality. Blood cholinesterase levels were not predictive of clinical outcome in decontaminated animals. The potential of "decontaminated" VX in open wounds to cause poisoning was assessed by vigorously mixing 5x LD(50) VX with the test decontaminants for 5 min and then placing the mixture onto a full-thickness skin wound. Soapy water was ineffective in preventing lethality. Although treatment with dry Fuller's earth prevented death and all signs of organophosphate poisoning, a significant proportion of treated animals decontaminated with Fuller's earth in aqueous suspension exhibited serious signs of organophosphate poisoning, suggesting that live agent may be desorbed from Fuller's earth when it is exposed to a liquid environment. Animals treated with reactive skin decontamination lotion or 0.5% hypochlorite-VX mixtures showed no signs of organophosphate poisoning during the 6- h test period.

  5. 29 CFR 1915.132 - Portable electric tools.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 7 2010-07-01 2010-07-01 false Portable electric tools. 1915.132 Section 1915.132 Labor... § 1915.132 Portable electric tools. The provisions of this section shall apply to ship repairing... frames of portable electric tools and appliances, except double insulated tools approved by...

  6. Decontamination of liquid radioactive waste by thorium phosphate

    Energy Technology Data Exchange (ETDEWEB)

    Rousselle, J.; Grandjean, S.; Dacheux, N.; Genet, M

    2004-07-01

    In the field of the complete reexamination of the chemistry of thorium phosphate and of the improvement of the homogeneity of Thorium Phosphate Diphosphate (TPD, Th{sub 4}(PO{sub 4}){sub 4}P{sub 2}O{sub 7}) prepared at high temperature, several crystallized compounds were prepared as initial powdered precursors. Due to the very low solubility products associated to these phases, their use in the field of the efficient decontamination of high-level radioactive liquid waste containing actinides (An) was carefully considered. Two main processes (called 'oxalate' and 'hydrothermal' chemical routes) were developed through a new concept combining the decontamination of liquid waste and the immobilization of the actinides in a ceramic matrix (TPD). In phosphoric media ('hydrothermal route'), the key-precursor was the Thorium Phosphate Hydrogen Phosphate hydrate (Th{sub 2}(PO{sub 4}){sub 2}(HPO{sub 4}). H{sub 2}O, TPHP, solubility product log(K{sub S,0}{sup 0}) {approx} - 67). The replacement of thorium by other tetravalent actinides (U, Np, Pu) in the structure, leading to the preparation of Th{sub 2-x/2}An{sub x/2}(PO{sub 4}){sub 2}(HPO{sub 4}). H{sub 2}O solid solutions, was examined. A second method was also considered in parallel to illustrate this concept using the more well-known precipitation of oxalate as the initial decontamination step. For this method, the final transformation to single phase TPD containing actinides was purchased by heating a mixture of phosphate ions with the oxalate precipitate at high temperature. (authors)

  7. Method for Cs-137 separation from the decontamination solutions

    Energy Technology Data Exchange (ETDEWEB)

    Toropov, I.G.; Efremenkov, V.M.; Toropova, V.V.; Satsukevich, V.M.; Davidov, Yu.P.

    1995-12-31

    In this work results of investigations are presented on separation of radiocaesium from the decontamination solutions containing reducing agents (thiocarbamide). The scientific basis for radiocaesium removal from the solution focuses on the state of the radionuclide and its sorption behavior in the solution with a complicated composition. Then using a combination of sorption and ultrafiltration methods it would be possible to concentrate the radionuclide in a small volume and to purify the main part of the solution. As a sorbent for radiocaesium removal from the solution, a ferrocyanide based sorbent is proposed. Use of this sorbent is justified since its high selectivity and effectiveness for radiocaesium sorption from the solutions of different composition is well known. When synthesis of the sorbent is performed directly in the treating solution, two components as a minimum should be added to it, namely K{sub 4}Fe(CN){sub 6} and metal ions of Ni-II, Co-II, Cu-II, etc. The results are presented which show the possibility of radiocaesium separation from the decontamination solutions (containing 60--100 g/l of salts) using sorption and membrane separation methods without the use of metal salts. At the same time by using FE-2 in solution in the presence of cyanide ions and thiocarbamide, it is possible to avoid the addition of metal salts (Ni, Cu, etc.). Utilization of the proposed method for spent decontamination solution treatment allows a relatively easy way to reduce the concentration of radiocaesium in solution on 2--4 orders of magnitudes, and to exclude the utilization of relatively expensive metal salts.

  8. A state of the art on the chemical gel decontamination technology

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Chong Hun; Moon, J. K.; Won, H. J.; Lee, K. W.; Kim, C. K. [KAERI, Daejeon (Korea, Republic of)

    2010-12-15

    Overseas, highly radioactive hot cell facilities has been aging and was contaminated with radioactivity inside through reprocessing research activities. These facilities enhance the safety regulations and the need for change in any other purposes or complete demolition of these facilities, is growing. As the increase of the operation age of the domestic high radiation facilities such as IMEF, PIEF and DFDF, the necessity of decontamination and refurbishment of hot cells in these facilities is also increased. Since the hot cell facilities has the limited space of the highly radioactive, high removal efficiency(a high DF, rapid decontamination), the remote control, and minimization of the 2nd waste is essential as an effective decontamination technology. Chemical gel decontamination technology that has the characteristics of rapid removal from large contaminated area and no waste arising, has been developed as one of main decontamination technologies. In this study, chemical contamination and decontamination chemistry with respect to chemical gel decontamination are examined, and the gel manufacturing precursors and control factors of the gel viscosity is described. In the high radiation hot cell facilities of the United States, France and other countries overseas, demonstration and application cases on site, and R and D status of the chemical gel decontamination technology have been investigated. This requires the current level of technology and related research topics were derived

  9. A State of the Art Report on the Case Study of Hot Cell Decontamination and Refurbishment

    Energy Technology Data Exchange (ETDEWEB)

    Won, H. J.; Jung, C. H.; Moon, J. K.; Park, G. I.; Song, K. C

    2008-08-15

    As the increase of the operation age of the domestic high radiation facilities such as IMEF, PIEF and DFDF, the necessity of decontamination and refurbishment of hot cells in these facilities is also increased. In the near future, the possibilities of refurbishment of hot cells in compliance with the new regulations, the reuse of hot cells for the other purposes and the decommissioning of the facilities also exist. To prepare against the decontamination and refurbishment of hot cells, the reports on the refurbishment, decommissioning and decontamination experiences of hot cells in USA, Japan, France, Belgium and Great Britain were investigated. ANL of USA performed the project on the decontamination of hot cells. The purpose of the project was to practically eliminate the radioactive emissions of Rn-220 to the environment and to restore the hot cells to an empty restricted use condition. The five hot cells were emptied and decontaminated for restricted use. Chemical processing facility in JAEA of Japan was used for the reprocessing study of spent fuels, hot cells in CPF were refurbished from 1995 for the tests of the newly developed reprocessing process. In a first stage, decommissioning and decontamination were fully performed by the remote operation Then, decommissioning and decontamination were performed manually. By the newly developed process, they reported that the radiation exposure of workers were satisfactorily reduced. In the other countries, they also make an effort for the refurbishment and decontamination of hot cells and it is inferred that they accumulate experiences in these fields.

  10. For whom should we use selective decontamination of the digestive tract?

    NARCIS (Netherlands)

    de Smet, Anne Marie G. A.; Bonten, Marc J. M.; Kluytmans, Jan A. J. W.

    2012-01-01

    Purpose of review This review discusses the relevant studies on selective decontamination of the digestive tract (SDD) published between 2009 and mid-2011. Recent findings In a multicenter cluster-randomized cross-over study in the Netherlands, SDD and selective oropharyngeal decontamination (SOD) w

  11. Decontamination and Management of Human Remains Following Incidents of Hazardous Chemical Release

    Energy Technology Data Exchange (ETDEWEB)

    Hauschild, Veronique [U.S. Army Public Health Command; Watson, Annetta Paule [ORNL; Bock, Robert Eldon [ORNL

    2012-01-01

    Abstract Objective: To provide specific procedural guidance and resources for identification, assessment, control, and mitigation of compounds that may contaminate human remains resulting from chemical attack or release. Design: A detailed technical, policy, and regulatory review is summarized. Setting: Guidance is suitable for civilian or military settings where human remains potentially contaminated with hazardous chemicals may be present. Settings would include sites of transportation accidents, natural disasters, terrorist or military operations, mortuary affairs or medical examiner processing and decontamination points, and similar. Patients, Participants: While recommended procedures have not been validated with actual human remains, guidance has been developed from data characterizing controlled experiments with fabrics, materiel, and laboratory animals. Main Outcome Measure(s): Presentation of logic and specific procedures for remains management, protection and decontamination of mortuary affairs personnel, as well as decision criteria for determining when remains are sufficiently decontaminated so as to pose no chemical health hazard. Results: Established procedures and existing equipment/materiel available for decontamination and verification provide appropriate and reasonable means to mitigate chemical hazards from remains. Extensive characterization of issues related to remains decontamination indicates that supra-lethal concentrations of liquid chemical warfare agent VX may prove difficult to decontaminate and verify in a timely fashion. Specialized personnel can and should be called upon to assist with monitoring necessary to clear decontaminated remains for transport and processing. Conclusions: Once appropriate decontamination and verification have been accomplished, normal procedures for remains processing and transport to the decedent s family and the continental United States can be followed.

  12. Chem-Bio Self-Decontaminating Surfaces (Briefing Slides). AFRL Quarterly Summary on DARPA Effort

    Science.gov (United States)

    2007-12-05

    AFRL-RX-TY-TP-2008-4558 CHEM- BIO SELF-DECONTAMINATING SURFACES (BRIEFING SLIDES) AFRL QUARTERLY SUMMARY ON DARPA EFFORT Joseph D...distribution unlimited. Chem- Bio Self-Decontaminating Surfaces 2 Coupon Test Method Development Small scale aerosol test stand was optimized to

  13. Percutaneous toxicity and decontamination of soman, VX, and paraoxon in rats using detergents.

    Science.gov (United States)

    Misík, Jan; Pavliková, Růžena; Kuča, Kamil

    2013-06-01

    Highly toxic organophosphorus compounds (OPs) were originally developed for warfare or as agricultural pesticides. Today, OPs represent a serious threat to military personnel and civilians. This study investigates the in vivo decontamination of male Wistar rats percutaneously exposed to paraoxon and two potent nerve agents--soman (GD) and VX. Four commercial detergents were tested as decontaminants--Neodekont(TM), Argos(TM), Dermogel(TM), and FloraFree(TM). Decontamination performed 2 min after exposure resulted in a higher survival rate in comparison with non-decontaminated controls. The decontamination effectiveness was expressed as protective ratio (PR, median lethal dose of agent in decontaminated animals divided by the median lethal dose of agent in untreated animals). The highest decontamination effectiveness was consistently achieved with Argos(TM) (PR=2.3 to 64.8), followed by Dermogel(TM) (PR=2.4 to 46.1). Neodekont(TM) and FloraFree(TM) provided the lowest decontamination effectiveness, equivalent to distilled water (PR=1.0 to 43.2).

  14. 40 CFR 265.114 - Disposal or decontamination of equipment, structures and soils.

    Science.gov (United States)

    2010-07-01

    ... equipment, structures and soils. 265.114 Section 265.114 Protection of Environment ENVIRONMENTAL PROTECTION... decontamination of equipment, structures and soils. During the partial and final closure periods, all contaminated equipment, structures and soil must be properly disposed of, or decontaminated unless specified otherwise...

  15. Advanced technologies for decontamination and conversion of scrap metal

    Energy Technology Data Exchange (ETDEWEB)

    Muth, T.R.; Shasteen, K.E.; Liby, A.L. [Manufacturing Sciences Corp., Oak Ridge, TN (United States)] [and others

    1995-10-01

    The Department of Energy (DOE) accumulated large quantities of radioactive scrap metal (RSM) through historic maintenance activities. The Decontamination and Decommissioning (D&D) of major sites formerly engaged in production of nuclear materials and manufacture of nuclear weapons will generate additional quantities of RSM, as much as 3 million tons of such metal according to a recent study. The recycling of RSM is quickly becoming appreciated as a key strategy in DOE`s cleanup of contaminated sites and facilities. The work described here has focused on recycle of the concentrated and high-value contaminated scrap metal resource that will arise from cleanup of DOE`s gaseous diffusion plants.

  16. Unit for air decontamination; Unidad para descontaminacion de aire

    Energy Technology Data Exchange (ETDEWEB)

    Mariano H, E

    1991-02-15

    To fulfill the applicable requirements of safety to the ventilation systems in nuclear facilities, it is necessary to make a cleaning of the air that hurtles to the atmosphere. For that which was designed and it manufactured an unit for decontamination of the air for the Pilot plant of production of Nuclear Fuel that this built one with national parts, uses Hepa national filters and the design can adapt for different dimensions of filters, also can be added a lodging for a prefilter or to adopt two Hepa filters. (Author)

  17. [Detection of enzyme activity in decontaminated spices in industrial use].

    Science.gov (United States)

    Müller, R; Theobald, R

    1995-03-01

    A range of decontaminated species of industrial use have been examined for their enzymes (catalase, peroxidase, amylase, lipase activity). The genuine enzymes remain fully active in irradiated spices, whereas the microbial load is clearly reduced. In contrast steam treated spices no longer demonstrate enzyme activities. Steam treatment offers e.g. black pepper without lipase activity, which can no longer cause fat deterioration. Low microbial load in combination with clearly detectable enzyme activity in spices is an indication for irradiation, whereas, reduced microbial contamination combined with enzyme inactivation indicate steam treatment of raw material.

  18. [Biological decontamination of the imprints obtained from different dental materials].

    Science.gov (United States)

    Brekhlichuk, P P; Petrov, V O; Bati, V V; Levchuk, O B; Boĭko, N V

    2013-01-01

    Microbiological contamination of the imprints made of alginate ("Ypeen") and silicone material ("Speedex") with and without the correction supplement has been investigated. Streptococcus and Staphylococcus have been estimated to be the most survivable species on the imprint surface, however their concentration differ depending on the type of imprints' material. The strains resistant to antibiotics dominated among all the isolated microorganisms. Bacterial preparations based on Bacillus - Biosporin and Subalin and some extracts of edible plants, fruits and berries can be used in dentistry for the decontamination of imprints obtained by the use of different materials.

  19. Improved Technologies for Decontamination of Crated Large Metal Objects

    Energy Technology Data Exchange (ETDEWEB)

    McFee, J.; Barbour, K.; Stallings, E.

    2003-02-25

    The Los Alamos Large Scale Demonstration and Deployment Project (LSDDP) in support of the US Department of Energy (DOE) Deactivation and Decommissioning Focus Area (DDFA) has been identifying and demonstrating technologies to reduce the cost and risk of management of transuranic element contaminated large metal objects, i.e. gloveboxes. DOE must dispose of hundreds of gloveboxes from Rocky Flats Environmental Technology Site (RFETS), Los Alamos National Laboratory (LANL), and other DOE sites. This paper reports on the results of four technology demonstrations on decontamination of plutonium contaminated gloveboxes with each technology compared to a common baseline technology, wipedown with nitric acid.

  20. Development of high-level radioactive waste treatment and conversion technologies 'Dry decontamination technology development for highly radioactive contaminants'

    Energy Technology Data Exchange (ETDEWEB)

    Oh, Won Zin; Lee, K. W.; Won, H. J.; Jung, C. J.; Choi, W. K.; Kim, G. N.; Moon, J. K

    2001-04-01

    The followings were studied through the project entitled 'Dry Decontamination Technology Development for Highly Radioactive Contaminants'. 1.Contaminant Characteristics Analysis of Domestic Nuclear Fuel Cycle Projects(NFCP) and Applicability Study of the Unit Dry-Decontamination Techniques A. Classification of contaminated equipments and characteristics analysis of contaminants B. Applicability study of the unit dry-decontamination techniques 2.Performance Evaluation of Unit Dry Decontamination Technique A. PFC decontamination technique B. CO2 decontamination technique C. Plasma decontamination technique 3.Development of Residual Radiation Assessment Methodology for High Radioactive Facility Decontamination A. Development of radioactive nuclide diffusion model on highly radioactive facility structure B. Obtainment of the procedure for assessment of residual radiation dose 4.Establishment of the Design Concept of Dry Decontamination Process Equipment Applicable to Highly Radioactive Contaminants 5.TRIGA soil unit decontamination technology development A. Development of soil washing and flushing technologies B. Development of electrokinetic soil decontamination technology.

  1. Japan, one year after. In Fukushima, a decontamination by forced march; Japon, un an apres. A Fukushima, une decontamination a marche forcee

    Energy Technology Data Exchange (ETDEWEB)

    Leglu, D.; Mulot, R.; Khalathari, A.; Lafon, B.; Stanley, T.; Linton, M.

    2012-03-15

    In a first part, the author describes how people living in the contaminated area around Fukushima try to deal with the difficult and almost impossible decontamination of their houses, gardens, schools, and so on. The destruction of forests is planned as they concentrate radioactivity. Thousands of inhabitants must wear dosimeters. An article comments the caesium activity measurements. Several data and figures are presented: evacuation areas, radioactive emissions and releases, doses received by emergency personnel, size of areas to be decontaminated, impact on the Japanese energy sector, contamination rates for soils and seawater, decontamination and dismantling costs, health impacts. An article proposes an overview of the different methods which are implemented and tested by the Japanese for large scale decontamination

  2. Efficacy of scalp hair decontamination following exposure to vapours of sulphur mustard simulants 2-chloroethyl ethyl sulphide and methyl salicylate.

    Science.gov (United States)

    Spiandore, Marie; Piram, Anne; Lacoste, Alexandre; Prevost, Philippe; Maloni, Pascal; Torre, Franck; Asia, Laurence; Josse, Denis; Doumenq, Pierre

    2017-04-01

    Chemical warfare agents are an actual threat and victims' decontamination is a main concern when mass exposure occurs. Skin decontamination with current protocols has been widely documented, as well as surface decontamination. However, considering hair ability to trap chemicals in vapour phase, we investigated hair decontamination after exposure to sulphur mustard simulants methyl salicylate and 2-chloroethyl ethyl sulphide. Four decontamination protocols were tested on hair, combining showering and emergency decontamination (use of Fuller's earth or Reactive Skin Decontamination Lotion RSDL(®)). Both simulants were recovered from hair after treatment, but contents were significantly reduced (42-85% content allowance). Showering alone was the least efficient protocol. Concerning 2-chloroethyl ethyl sulphide, protocols did not display significant differences in decontamination efficacy. For MeS, use of emergency decontaminants significantly increased showering efficacy (10-20% rise), underlining their usefulness before thorough decontamination. Our results highlighted the need to extensively decontaminate hair after chemical exposure. Residual amounts after decontamination are challenging, as their release from hair could lead to health issues. Copyright © 2016. Published by Elsevier B.V.

  3. Development of Novel Decontamination Techniques for Chemical Agents (GB, VX, HD) Contaminated Facilities. Phase 1. Identification and Evaluation of Novel Decontamination Concepts. Volume 2

    Science.gov (United States)

    1983-02-01

    composition reaction the effect will be probably smal I. 4.2.2 Removal or Reaction of Contaminant from Surface Complete decontamination of all surfaces is...spallIng and descaling . 1.2 Origination of Idea Used in the decontamination of nuclear facilities ond described in deta’l in the Decommissioning Handbook...for RD. 1.4 Variations of Idea Various application methods could be used including sprays, foams, gels , creams, etc. Inclusion of an additive might make

  4. Chemical, biological, radiological, and nuclear decontamination: Recent trends and future perspective

    Directory of Open Access Journals (Sweden)

    Vinod Kumar

    2010-01-01

    Full Text Available Chemical, biological, radiological, and nuclear (CBRN decontamination is the removal of CBRN material from equipment or humans. The objective of the decontamination is to reduce radiation burden, salvage equipment, and materials, remove loose CBRN contaminants, and fix the remaining in place in preparation for protective storage or permanent disposal work activities. Decontamination may be carried out using chemical, electrochemical, and mechanical means. Like materials, humans may also be contaminated with CBRN contamination. Changes in cellular function can occur at lower radiation doses and exposure to chemicals. At high dose, cell death may take place. Therefore, decontamination of humans at the time of emergency while generating bare minimum waste is an enormous task requiring dedication of large number of personnel and large amount of time. General principles of CBRN decontamination are discussed in this review with emphasis on radiodecontamination.

  5. Decontamination of VX, GD, and HD on a surface using modified vaporized hydrogen peroxide.

    Science.gov (United States)

    Wagner, George W; Sorrick, David C; Procell, Lawrence R; Brickhouse, Mark D; Mcvey, Iain F; Schwartz, Lewis I

    2007-01-30

    Vaporized hydrogen peroxide (VHP) has proven efficacy for biological decontamination and is a common gaseous sterilant widely used by industry. Regarding chemical warfare agent decontamination, VHP is also effective against HD and VX, but not GD. Simple addition of ammonia gas to VHP affords reactivity toward GD, while maintaining efficacy for HD (and bioagents) and further enhancing efficacy for VX. Thus, modified VHP is a broad-spectrum CB decontaminant suitable for fumigant-type decontamination scenarios, i.e., building, aircraft, and vehicle interiors and sensitive equipment. Finally, as an interesting aside to the current study, commercial ammonia-containing cleaners are also shown to be effective surface decontaminants for GD, but not for VX or HD.

  6. Development and application of ozone chemical decontamination for nuclear power station

    Energy Technology Data Exchange (ETDEWEB)

    Enda, Masami; Yaita, Yumi; Inami, Ichiro; Sakai, Hitoshi [Toshiba Corp. (Japan). Power systems and Services Company; Nakagami, Motoyori; Kani, Kazuhiro [Chubu Electric Power Co. Inc., Nagoya (Japan)

    2003-03-01

    By focusing to use gaseous ozone for an oxidant under aiming to further reduce amounts of the secondary wastes, ozone chemical decontamination technique was developed. Here were described results of investigation on a process applying ozone to oxidation process for chemical decontamination and of application to decontamination of contaminated machine. As a result carrying out the contaminated machine, it was found that , 1) temperature of ozone water processing at solution test of chromium oxide using ozone water was selected to 80 centigrade, 2) ozone concentration of ozone water using for decontamination test of metal test pieces polluted by radioactive materials was more than 1 ppm, and 3) ion-exchange resins consumed by decontamination agents could be regenerated by using a third of amounts of permanganic acid. (G.K.)

  7. Electrolytic decontamination of metal low level waste (LLW) and mixed low level waste (MLLW)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-11-01

    Metal objects resulting from ER activities were decontaminated using electrolytic methods. The project involved about 500 kg of ballistic test projectiles, 23 augers and drill heads, and 50 pieces of shrapnel containing lead. All objects were free-released and either reclaimed as scrap metal or reused. Electrolytic decontamination was proven to be an effective method to decontaminate metal waste objects to free-release standards. A cost analysis showed the process to be economical, especially when applied to decontamination of mixed waste, TRU waste, or when the recovered materials could be reused or recycled. The cost of decontamination of scrap iron is approximately equal to the cost of its land disposal as low level waste.

  8. Guide on the use of low energy electron beams for microbiological decontamination of surfaces

    DEFF Research Database (Denmark)

    Miller, Arne; Helt-Hansen, Jakob; Gondim, Ondina

    This Guide describes the validation and routine monitoring of microbiological decontamination of surfaces by low energy electron beams (100-200 keV). The Guide is mainly based on experience gained in connection with installation of electron beam systems for surface decontamination of pre-steriliz......This Guide describes the validation and routine monitoring of microbiological decontamination of surfaces by low energy electron beams (100-200 keV). The Guide is mainly based on experience gained in connection with installation of electron beam systems for surface decontamination of pre......-sterilized containers at several aseptic filling lines at pharmaceutical manufacturers. Its main emphasis is on the dosimetric measurements that should be carried out for the validation of the decontamination process and on establishing the appropriate effective dose. Other aspects such as use of measurement...... uncertainties and formation of radiation induced by-products are also addressed....

  9. Adh enhances Actinobacillus pleuropneumoniae pathogenicity by binding to OR5M11 and activating p38 which induces apoptosis of PAMs and IL-8 release.

    Science.gov (United States)

    Wang, Lei; Qin, Wanhai; Zhang, Jing; Bao, Chuntong; Zhang, Hu; Che, Yanyi; Sun, Changjiang; Gu, Jingmin; Feng, Xin; Du, Chongtao; Han, Wenyu; Richard, Paul Langford; Lei, Liancheng

    2016-04-05

    Members of the Trimeric Autotransporter Adhesin (TAA) family play a crucial role in the adhesion of Gram-negative pathogens to host cells, but the immunopathogenesis of TAAs remains unknown. Our previous studies demonstrated that Adh from Actinobacillus pleuropneumoniae (A. pleuropneumoniae) is required for full bacterial pathogenicity. Alveolar macrophages are the first line of defense against respiratory infections. This study compared the interactions between porcine alveolar macrophages (PAMs) and wild-type A. pleuropneumoniae (5b WT) or an Adh-deletion strain (5b ΔAdh) via gene microarray, immunoprecipitation and other technologies. We found that Adh was shown to interact with the PAMs membrane protein OR5M11, an olfactory receptor, resulting in the high-level secretion of IL-8 by activation of p38 MAPK signaling pathway. Subsequently, PAMs apoptosis via the activation of the Fax and Bax signaling pathways was observed, followed by activation of caspases 8, 9, and 3. The immunological pathogenic roles of Adh were also confirmed in both murine and piglets infectious models in vivo. These results identify a novel immunological strategy for TAAs to boost the pathogenicity of A. pleuropneumoniae. Together, these datas reveal the high versatility of the Adh protein as a virulence factor and provide novel insight into the immunological pathogenic role of TAAs.

  10. Harmonic Vibrational Frequencies: Approximate Global Scaling Factors for TPSS, M06, and M11 Functional Families Using Several Common Basis Sets.

    Science.gov (United States)

    Kashinski, D O; Chase, G M; Nelson, R G; Di Nallo, O E; Scales, A N; VanderLey, D L; Byrd, E F C

    2017-03-23

    We propose new approximate global multiplicative scaling factors for the DFT calculation of ground state harmonic vibrational frequencies using functionals from the TPSS, M06, and M11 functional families with standard correlation consistent cc-pVxZ and aug-cc-pVxZ (x = D, T, and Q), 6-311G split valence family, Sadlej and Sapporo polarized triple-ζ basis sets. Results for B3LYP, CAM-B3LYP, B3PW91, PBE, and PBE0 functionals with these basis sets are also reported. A total of 99 harmonic frequencies were calculated for 26 gas-phase organic and nonorganic molecules typically found in detonated solid propellant residue. Our proposed approximate multiplicative scaling factors are determined using a least-squares approach comparing the computed harmonic frequencies to experimental counterparts well established in the scientific literature. A comparison of our work to previously published global scaling factors is made to verify method reliability and the applicability of our molecular test set.

  11. CO{sub 2} pellet blasting literature search and decontamination scoping tests report

    Energy Technology Data Exchange (ETDEWEB)

    Archibald, K.E.

    1993-12-01

    Past decontamination and solvent recovery activities at the Idaho Chemical Processing Plant (ICPP) have resulted in the accumulation of 1.5 million gallons of radioactively contaminated sodium-bearing liquid waste. Future decontamination activities at the ICPP could result in the production of 5 million gallons or more of sodium-bearing waste using current decontamination techniques. Chemical decontamination flushes have provided a satisfactory level of decontamination. However, this method generates large amounts of sodium-bearing secondary waste. Steam jet cleaning has also been used with a great deal of success but cannot be used on concrete or soft materials. With the curtailment of reprocessing at the ICPP, the focus of decontamination is shifting from maintenance for continued operation of the facilities to decommissioning. Treatment of sodium-bearing waste is a particularly difficult problem due to the high content of alkali metals in the sodium-bearing liquid waste. It requires a very large volume of cold chemical additive for calcination. In addition, the sodium content of the sodium-bearing waste exceeds the limit that can be incorporated into vitrified waste without the addition of glass-forming compounds (primarily silicon) to produce an acceptable immobilized waste form. The primary initiatives of the Decontamination Development Program is the development of methods to eliminate/minimize the use of sodium-bearing decontamination chemicals and to minimize all liquid decontamination wastes. One method chosen for cold scoping studies during FY-93 was CO{sub 2} pellet blasting. CO{sub 2} pellet blasting has been used extensively by commercial industries for general cleaning. However, using this method for decontamination of nuclear materials is a fairly new concept. The following report discusses the research and scoping tests completed on CO{sub 2} pellet blasting.

  12. Effectiveness of three decontamination treatments against influenza virus applied to filtering facepiece respirators.

    Science.gov (United States)

    Lore, Michael B; Heimbuch, Brian K; Brown, Teanne L; Wander, Joseph D; Hinrichs, Steven H

    2012-01-01

    Filtering facepiece respirators (FFRs) are recommended for use as precautions against airborne pathogenic microorganisms; however, during pandemics demand for FFRs may far exceed availability. Reuse of FFRs following decontamination has been proposed but few reported studies have addressed the feasibility. Concerns regarding biocidal efficacy, respirator performance post decontamination, decontamination cost, and user safety have impeded adoption of reuse measures. This study examined the effectiveness of three energetic decontamination methods [ultraviolet germicidal irradiation (UVGI), microwave-generated steam, and moist heat] on two National Institute for Occupational Safety and Health-certified N95 FFRs (3M models 1860s and 1870) contaminated with H5N1. An aerosol settling chamber was used to apply virus-laden droplets to FFRs in a method designed to simulate respiratory deposition of droplets onto surfaces. When FFRs were examined post decontamination by viral culture, all three decontamination methods were effective, reducing virus load by > 4 log median tissue culture infective dose. Analysis of treated FFRs using a quantitative molecular amplification assay (quantitative real-time polymerase chain reaction) indicated that UVGI decontamination resulted in lower levels of detectable viral RNA than the other two methods. Filter performance was evaluated before and after decontamination using a 1% NaCl aerosol. As all FFRs displayed <5% penetration by 300-nm particles, no profound reduction in filtration performance was caused in the FFRs tested by exposure to virus and subsequent decontamination by the methods used. These findings indicate that, when properly implemented, these methods effectively decontaminate H5N1 on the two FFR models tested and do not drastically affect their filtering function; however, other considerations may influence decisions to reuse FFRs.

  13. Catalytic microreactors for portable power generation

    Energy Technology Data Exchange (ETDEWEB)

    Karagiannidis, Symeon [Paul Scherer Institute, Villigen (Switzerland)

    2011-07-01

    ''Catalytic Microreactors for Portable Power Generation'' addresses a problem of high relevance and increased complexity in energy technology. This thesis outlines an investigation into catalytic and gas-phase combustion characteristics in channel-flow, platinum-coated microreactors. The emphasis of the study is on microreactor/microturbine concepts for portable power generation and the fuels of interest are methane and propane. The author carefully describes numerical and experimental techniques, providing a new insight into the complex interactions between chemical kinetics and molecular transport processes, as well as giving the first detailed report of hetero-/homogeneous chemical reaction mechanisms for catalytic propane combustion. The outcome of this work will be widely applied to the industrial design of micro- and mesoscale combustors. (orig.)

  14. Portable power applications of fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Weston, M.; Matcham, J.

    2002-07-01

    This report describes the state-of-the-art of fuel cell technology for portable power applications. The study involved a comprehensive literature review. Proton exchange membrane fuel cells (PEMFCs) have attracted much more interest than either direct methanol fuel cells (DMFCs) or solid oxide fuel cells (SOFCs). However, issues relating to fuel choice and catalyst design remain with PEMFCs; DMFCs have excellent potential provided issues relating to the conducting membrane can be resolved but the current high temperature of operation and low power density currently makes SOFCs less applicable to portable applications. Available products are listed and the obstacles to market penetration are discussed. The main barriers are cost and the size/weight of fuel cells compared with batteries. Another key problem is the lack of a suitable fuel infrastructure.

  15. Decontamination of control rod housing from Palisades Nuclear Power Station.

    Energy Technology Data Exchange (ETDEWEB)

    Kaminski, M.D.; Nunez, L.; Purohit, A.

    1999-05-03

    Argonne National Laboratory has developed a novel decontamination solvent for removing oxide scales formed on ferrous metals typical of nuclear reactor piping. The decontamination process is based on the properties of the diphosphonic acids (specifically 1-hydroxyethane-1,1-diphosphonic acid or HEDPA) coupled with strong reducing-agents (e.g., sodium formaldehyde sulfoxylate, SFS, and hydroxylamine nitrate, HAN). To study this solvent further, ANL has solicited actual stainless steel piping material that has been recently removed from an operating nuclear reactor. On March 3, 1999 ANL received segments of control rod housing from Consumers Energy's Palisades Nuclear Plant (Covert, MI) containing radioactive contamination from both neutron activation and surface scale deposits. Palisades Power plant is a PWR type nuclear generating plant. A total of eight segments were received. These segments were from control rod housing that was in service for about 6.5 years. Of the eight pieces that were received two were chosen for our experimentation--small pieces labeled Piece A and Piece B. The wetted surfaces (with the reactor's pressurized water coolant/moderator) of the pieces were covered with as a scale that is best characterized visually as a smooth, shiny, adherent, and black/brown in color type oxide covering. This tenacious oxide could not be scratched or removed except by aggressive mechanical means (e.g., filing, cutting).

  16. Decontamination and decommissioning project for the nuclear facilities

    Energy Technology Data Exchange (ETDEWEB)

    Park, J. H.; Paik, S. T.; Park, S. W. (and others)

    2007-02-15

    The final goal of this project is to complete the decommissioning of the Korean Research Reactor no.1 and no. 2(KRR-1 and 2) and uranium conversion plant safely and successfully. The goal of this project in 2006 is to complete the decontamination of the inside reactor hall of the KRR-2 which will be operating as a temporary storage for the radioactive waste until the construction and operation of the national repository site. Also the decommissioning work of the KRR-1 and auxiliary facilities is being progress. As the compaction of decommissioning project is near at hand, a computer information system was developed for a systematically control and preserve a technical experience and decommissioning data for the future reuse. The nuclear facility decommissioning, which is the first challenge in Korea, is being closed to the final stages. We completed the decommissioning of all the bio-shielding concrete for KRR-2 in 2005 and carried out the decontamination and waste material grouping of the roof, wall and bottom of the reactor hall of the KRR-2. The decommissioning for nuclear facility were demanded the high technology, remote control equipment and radioactivity analysis. So developed equipment and experience will be applied at the decommissioning for new nuclear facility in the future.

  17. Mechanical decontamination tests in areas affected by the Chernobyl accident

    Energy Technology Data Exchange (ETDEWEB)

    Roed, J.; Andersson, K.G.; Barkovsky, A.N.; Fogh, C.L.; Mishine, A.S.; Olsen, S.K.; Ponamarjov, A.V.; Prip, H.; Ramzaev, V.P.; Vorobiev, B.F

    1998-08-01

    Decontamination was carried out around three houses in Novo Bobovichi, Russia, in the summer of 1997. It was demonstrated that significant reductions in the dose rate both indoor (DRF = 0.27) and outdoor (DRF = 0.17) can be achieved when a careful cleaning is undertaken. This report describes the decontamination work carried out and the results obtained. The roof of one of the houses was replaced with a new roof. This reduced the Chernobyl related dose rate by 10% at the ground floor and by 27% at the first floor. The soil around the houses was removed by a bobcat, while carefully monitoring the ground for residual contamination with handheld dose meters. By monitoring the decline in the dose rate during the different stages of the work the dose reducing effect of each action has been estimated. This report also describes a test of a skim-and-burial plough developed especially for treatment of contaminated land. In the appendices of the report the measurement data is available for further analysis. (au) 24 tabs., 75 ills., 33 refs.

  18. Potential of Biological Agents in Decontamination of Agricultural Soil

    Directory of Open Access Journals (Sweden)

    Muhammad Kashif Javaid

    2016-01-01

    Full Text Available Pesticides are widely used for the control of weeds, diseases, and pests of cultivated plants all over the world, mainly since the period after the Second World War. The use of pesticides is very extensive to control harm of pests all over the globe. Persistent nature of most of the synthetic pesticides causes serious environmental concerns. Decontamination of these hazardous chemicals is very essential. This review paper elaborates the potential of various biological agents in decontamination of agricultural soils. The agricultural crop fields are contaminated by the periodic applications of pesticides. Biodegradation is an ecofriendly, cost-effective, highly efficient approach compared to the physical and chemical methods which are expensive as well as unfriendly towards environment. Biodegradation is sensitive to the concentration levels of hydrogen peroxide and nitrogen along with microbial community, temperature, and pH changes. Experimental work for optimum conditions at lab scale can provide very fruitful results about specific bacterial, fungal strains. This study revealed an upper hand of bioremediation over physicochemical approaches. Further studies should be carried out to understand mechanisms of biotransformation.

  19. Tritium contamination and decontamination of sealing oil for vacuum pump

    Energy Technology Data Exchange (ETDEWEB)

    Takeishi, T.; Kotoh, K.; Kawabata, Y.; Tanaka, J.I. [Faculty of Engineering, Kyushu University, Nishi-ku, Fukuoka (Japan); Kawamura, S.; Iwata, M. [ATOX Co. Ltd, Technoly Development Center, Kashiwa, Chiba (Japan)

    2015-03-15

    The existence of tritium-contaminated oils from vacuum pumps used in tritium facilities, is becoming an important issue since there is no disposal way for tritiated waste oils. On recovery of tritiated water vapor in gas streams, it is well-known that the isotope exchange reaction between the gas phase and the liquid phase occurs effectively at room temperature. We have carried out experiments using bubbles to examine the tritium contamination and decontamination of a volume of rotary-vacuum-pump oil. The contamination of the pump oil was made by bubbling tritiated water vapor and tritiated hydrogen gas into the oil. Subsequently the decontamination was processed by bubbling pure water vapor and dry argon gas into the tritiated oil. Results show that the water vapor bubbling was more effective than dry argon gas. The experiment also shows that the water vapor bubbling in an oil bottle can remove and transfer tritium efficiently from the tritiated oil into another water-bubbling bottle.

  20. Decontamination and decommissioning surveillance and maintenance report for FY 1991

    Energy Technology Data Exchange (ETDEWEB)

    Gunter, David B.; Burwinkle, T. W.; Cannon, T. R.; Ford, M. K.; Holder, Jr., L.; Clotfelter, O. K.; Faulkner, R. L.; Smith, D. L.; Wooten, H. O.

    1991-12-01

    The Decontamination and Decommissioning (D D) Program has three distinct phases: (1) surveillance and maintenance (S M); (2) decontamination and removal of hazardous materials and equipment (which DOE Headquarters in Washington, D.C., calls Phase I of remediation); and (3) decommissioning and ultimate disposal, regulatory compliance monitoring, and property transfer (which DOE Headquarters calls Phase II of remediation). A large part of D D is devoted to S M at each of the sites. Our S M activities, which are performed on facilities awaiting decommissioning, are designed to minimize potential hazards to human health and the environment by: ensuring adequate containment of residual radioactive and hazardous materials; and, providing physical safety and security controls to minimize potential hazards to on-site personnel and the general public. Typically, we classify maintenance activities as either routine or special (major repairs). Routine maintenance includes such activities as painting, cleaning, vegetation control, minor structural repairs, filter changes, and building system(s) checks. Special maintenance includes Occupational Safety and Health Act facility upgrades, roof repairs, and equipment overhaul. Surveillance activities include inspections, radiological measurements, reporting, records maintenance, and security (as required) for controlling and monitoring access to facilities. This report summarizes out FY 1991 S M activities for the Tennessee plant sites, which include the K-25 Site, the Gas Centrifuge facilities, ORNL, and the Y-12 Plant.

  1. Potential of Biological Agents in Decontamination of Agricultural Soil

    Science.gov (United States)

    Javaid, Muhammad Kashif; Ashiq, Mehrban; Tahir, Muhammad

    2016-01-01

    Pesticides are widely used for the control of weeds, diseases, and pests of cultivated plants all over the world, mainly since the period after the Second World War. The use of pesticides is very extensive to control harm of pests all over the globe. Persistent nature of most of the synthetic pesticides causes serious environmental concerns. Decontamination of these hazardous chemicals is very essential. This review paper elaborates the potential of various biological agents in decontamination of agricultural soils. The agricultural crop fields are contaminated by the periodic applications of pesticides. Biodegradation is an ecofriendly, cost-effective, highly efficient approach compared to the physical and chemical methods which are expensive as well as unfriendly towards environment. Biodegradation is sensitive to the concentration levels of hydrogen peroxide and nitrogen along with microbial community, temperature, and pH changes. Experimental work for optimum conditions at lab scale can provide very fruitful results about specific bacterial, fungal strains. This study revealed an upper hand of bioremediation over physicochemical approaches. Further studies should be carried out to understand mechanisms of biotransformation. PMID:27293964

  2. Dismantlement and decontamination of a plutonium-238 facility at SRS

    Energy Technology Data Exchange (ETDEWEB)

    Smith, R.H. Jr.; Hootman, H.E.

    1994-01-01

    There has been very little, documented decontamination and decommissioning (D&D) experience on which to project cleanup costs and schedules for plutonium facilities at SRS and other DOE sites. A portion of the HB-Line, a plutonium-238 processing facility at SRS, has been undergoing D&D intermittently since 1984. Although this cleanup effort was not originally intended to quantify results, some key data have been project has demonstrated effective methods of accumulated, and the performing D&D work, and has demonstrated cleanup equipment and techniques under conditions of high contamination. Plutonium facilities where D&D is already underway provide an opportunity for` timely field testing of characterization, size reduction, and decontamination techniques. Some data are presented here; however, more specific tests and data may be obtained during the remainder of this project. This project has been recommended as a candidate test facility for a DOE planned ``Integrated D&D Demonstration`` managed by EM-50 to develop and demonstrate technology for D&D and surplus facilities deactivation. Both the remainder of this project and the Integrated D&D Demonstration Program can benefit from a joint effort, and the, overall costs should be reduced.

  3. A comparative study of the bactericidal activity and daily disinfection housekeeping surfaces by a new portable pulsed UV radiation device.

    Science.gov (United States)

    Umezawa, Kazuo; Asai, Satomi; Inokuchi, Sadaki; Miyachi, Hayato

    2012-06-01

    Daily cleaning and disinfecting of non-critical surfaces in the patient-care areas are known to reduce the occurrence of health care-associated infections. However, the conventional means for decontamination of housekeeping surfaces of sites of frequent hand contact such as manual disinfection using ethanol wipes are laborious and time-consuming in daily practice. This study evaluated a newly developed portable pulsed ultraviolet (UV) radiation device for its bactericidal activity in comparison with continuous UV-C, and investigated its effect on the labor burden when implemented in a hospital ward. Pseudomonas aeruginosa, Multidrug-resistant P. aeruginosa, Escherichia coli, Acinetobacter baumannii, Amikacin and Ciprofloxacin-resistant A. baumannii, Staphylococcus aureus, Methicillin-resistant S. aureus and Bacillus cereus were irradiated with pulsed UV or continuous UV-C. Pulsed UV and continuous UV-C required 5 and 30 s of irradiation, respectively, to attain bactericidal activity with more than 2Log growth inhibition of all the species. The use of pulsed UV in daily disinfection of housekeeping surfaces reduced the working hours by half in comparison to manual disinfection using ethanol wipes. The new portable pulsed UV radiation device was proven to have a bactericidal activity against critical nosocomial bacteria, including antimicrobial-resistant bacteria after short irradiation, and was thus found to be practical as a method for disinfecting housekeeping surfaces and decreasing the labor burden.

  4. Performance Portability for Unstructured Mesh Physics

    Energy Technology Data Exchange (ETDEWEB)

    Keasler, J A

    2012-03-23

    ASC legacy software must be ported to emerging hardware architectures. This paper notes that many programming models used by DOE applications are similar, and suggests that constructing a common terminology across these models could reveal a performance portable programming model. The paper then highlights how the LULESH mini-app is used to explore new programming models with outside solution providers. Finally, we suggest better tools to identify parallelism in software, and give suggestions for enhancing the co-design process with vendors.

  5. Selection of Power Sources for Portable Applications

    OpenAIRE

    Flipsen, S.F.J.

    2009-01-01

    New power sources emerge very quickly. Implementation of hybrid power sources for portable electronics depends on the knowledge of industrial designers. For now this group has little understanding of fuel cells and especially fuel-cell hybrids. This slows down implementation and increases the chance of failure. In this paper a review is given of tools and methods which gives concept designers a first guesstimate of the volumes they have to deal with when designing the power source. Second the...

  6. Operational test report, 500 CFM portable exhauster

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, O.D.

    1997-05-15

    A 500 cubic foot per minute (CFM) portable exhauster system was fabricated for use on 241-A-101 [a Hydrogen Watch List tank] during saltwell pumping activities. An operational test was performed on this unit during 9/20/96 through 1O/14/96 in the 241-A Tank Farm. This operational test was done in accordance with OTP-060-001 Rev 0 (See Appendix A of this report). The test was performed with exceptions.

  7. Using a portable holographic camera in cosmetology

    Science.gov (United States)

    Bakanas, R.; Gudaitis, G. A.; Zacharovas, S. J.; Ratcliffe, D. B.; Hirsch, S.; Frey, S.; Thelen, A.; Ladrière, N.; Hering, P.

    2006-07-01

    The HSF-MINI portable holographic camera is used to record holograms of the human face. The recorded holograms are analyzed using a unique three-dimensional measurement system that provides topometric data of the face with resolution less than or equal to 0.5 mm. The main advantages of this method over other, more traditional methods (such as laser triangulation and phase-measurement triangulation) are discussed.

  8. Portable Electromagnetic Induction Sensor with Integrated Positioning

    Science.gov (United States)

    2012-04-16

    OF ABSTRACT Same as Report ( SAR ) 18. NUMBER OF PAGES 38 19a. NAME OF RESPONSIBLE PERSON a. REPORT unclassified b. ABSTRACT unclassified c...work is to design and fabricate a novel time-domain bistatic EMI sensor that allows for the physical decoupling of the transmitter (Tx) and receiver...Rx) coil(s). This bistatic , physically decoupled, portable EMI instrument with precise positioning would be a valuable re- search instrument for

  9. Miniature PCR based portable bioaerosol monitor development.

    Science.gov (United States)

    Agranovski, I E; Usachev, E V; Agranovski, E; Usacheva, O V

    2017-01-01

    A portable bioaerosol monitor is greatly demanded technology in many areas including air quality control, occupational exposure assessment and health risk evaluation, environmental studies and, especially, in defence and bio-terrorism applications. Our recent groundwork allowed us to formulate the concept of a portable bioaerosol monitor, which needs to be light, user friendly, reliable and capable of detecting airborne pathogens within 1-1·5 h on the spot. Conceptually, the event of a bioaerosol concentration burst is determined by triggers to commence the representative air sampling with sequential real-time polymerase chain reaction (PCR) confirmation of the targeted micro-organism present in the air. To minimize reagent consumption and idle running of the technology, an event of a bioaerosol burst is confirmed by three parameters: aerosol particle size, concentration and composition. Only particle sizes above 200 nm attract interest in the bioaerosol. Only an elevated aerosol concentration above the threshold (background aerosol concentration) is a signal to commence the analytical procedure. The combination of our previously developed personal bioaerosol sampler, aerosol particle counter based trigger and portable real-time PCR device formed the basis of the bioaerosol monitoring technology. The portable real-time PCR device was advanced to provide internally controlled detection, significantly reducing false-positive alarms. The technique is capable of detecting selected airborne micro-organisms on the spot within 30-80 min, depending on the genome organization of the particular strain. Due to recent outbreaks of infectious airborne diseases and the continuing threat of intentionally released bioaerosol attacks, investigations into the possibility of the early and reliable detection of pathogenic micro-organisms in the air is becoming increasingly important. The proposed technology consisting of a bioaerosol sampler, technology trigger and PCR device is

  10. A parallel, portable and versatile treecode

    Energy Technology Data Exchange (ETDEWEB)

    Warren, M.S. [Los Alamos National Lab., NM (United States); Salmon, J.K. [Australian National Univ., Canberra, ACT (Australia)]|[California Inst. of Technology, Pasadena, CA (United States)

    1994-10-01

    Portability and versatility are important characteristics of a computer program which is meant to be generally useful. We describe how we have developed a parallel N-body treecode to meet these goals. A variety of applications to which the code can be applied are mentioned. Performance of the program is also measured on several machines. A 512 processor Intel Paragon can solve for the forces on 10 million gravitationally interacting particles to 0.5% rms accuracy in 28.6 seconds.

  11. Performances of a portable electrospinning apparatus.

    Science.gov (United States)

    Mouthuy, Pierre-Alexis; Groszkowski, Lukasz; Ye, Hua

    2015-05-01

    To demonstrate that portable electrospinning devices can spin a wide range of polymers into submicron fibres and provide a mesh quality comparable to those produced with benchtop machines. We have designed a small, battery-operated electrospinning apparatus which enables control over the voltage and the flow rate of the polymer solution via a microcontroller. It can be used to electrospin a range of commonly used polymers including poly(ε-caprolactone), poly(p-dioxanone), poly(lactic-co-glycolic acid), poly(3-hydroxybutyrate), poly(ethylene oxide), poly(vinyl acohol) and poly(vinyl butyral). Moreover, electrospun meshes are produced with a quality comparable to a benchtop machine. We also show that the portable apparatus is able to electrospray beads and microparticles. Finally, we highlight the potential of the device for wound healing applications by demonstrating the possibility of electrospinning onto pig and human skins. Portable electrospinning devices are still at an early stage of development but they could soon become an attractive alternative to benchtop machines, in particular for uses that require mobility and a higher degree of flexibility, such as for wound healing applications.

  12. Decontamination of Surfaces by Ultrasonics; La decontamination des surfaces par l'emploi des ultra-sons

    Energy Technology Data Exchange (ETDEWEB)

    Cerre, P.; Mestre, E.; Kerdelleau, J. de [Commissariat a l' Energie Atomique. Centre d' Etudes Nucleaires de Saclay, 91 - Gif-sur-Yvette (France)

    1962-07-01

    A study was made of factors such as frequency, intensity, and time in the case of steel and of cotton cloth contaminated by fission products. Results show that the method is only of value in the case of steel and that it is necessary to operate at an optimum frequency of 80 khz and with an intensity of at least 4 W/cm{sup 2}. The difficulty of proposing a valid explanation for the decontamination mechanism is discussed. (authors) [French] Apres un examen des donnees theoriques du probleme, les auteurs font une etude systematique des facteurs frequence, intensite et temps dans le cas de l'acier et des tissus de coton contamines par des produits de fission. Ils montrent que la methode n'est interessante que pour l'acier qu'il faut operer a la frequence optimale de 80 kHz avec une intensite d'au moins 4 W/cm{sup 2}. Ils concluent en insistant sur la difficulte de proposer une explication valable pour le mecanisme de decontamination. (auteurs)

  13. Assessment of Environmental Contamination and Environmental Decontamination Practices within an Ebola Holding Unit, Freetown, Sierra Leone.

    Directory of Open Access Journals (Sweden)

    Daniel Youkee

    Full Text Available Evidence to inform decontamination practices at Ebola holding units (EHUs and treatment centres is lacking. We conducted an audit of decontamination procedures inside Connaught Hospital EHU in Freetown, Sierra Leone, by assessing environmental swab specimens for evidence of contamination with Ebola virus by RT-PCR. Swabs were collected following discharge of Ebola Virus Disease (EVD patients before and after routine decontamination. Prior to decontamination, Ebola virus RNA was detected within a limited area at all bedside sites tested, but not at any sites distant to the bedside. Following decontamination, few areas contained detectable Ebola virus RNA. In areas beneath the bed there was evidence of transfer of Ebola virus material during cleaning. Retraining of cleaning staff reduced evidence of environmental contamination after decontamination. Current decontamination procedures appear to be effective in eradicating persistence of viral RNA. This study supports the use of viral swabs to assess Ebola viral contamination within the clinical setting. We recommend that regular refresher training of cleaning staff and audit of environmental contamination become standard practice at all Ebola care facilities during EVD outbreaks.

  14. Decontamination and management of human remains following incidents of hazardous chemical release.

    Science.gov (United States)

    Hauschild, Veronique D; Watson, Annetta; Bock, Robert

    2012-01-01

    To provide specific guidance and resources for systematic and orderly decontamination of human remains resulting from a chemical terrorist attack or accidental chemical release. A detailed review and health-based decision criteria protocol is summarized. Protocol basis and logic are derived from analyses of compound-specific toxicological data and chemical/physical characteristics. Guidance is suitable for civilian or military settings where human remains potentially contaminated with hazardous chemicals may be present, such as sites of transportation accidents, terrorist operations, or medical examiner processing points. Guidance is developed from data-characterizing controlled experiments with laboratory animals, fabrics, and materiel. Logic and specific procedures for decontamination and management of remains, protection of mortuary affairs personnel, and decision criteria to determine when remains are sufficiently decontaminated are presented. Established procedures as well as existing materiel and available equipment for decontamination and verification provide reasonable means to mitigate chemical hazards from chemically exposed remains. Unique scenarios such as those involving supralethal concentrations of certain liquid chemical warfare agents may prove difficult to decontaminate but can be resolved in a timely manner by application of the characterized systematic approaches. Decision criteria and protocols to "clear" decontaminated remains for transport and processing are also provided. Once appropriate decontamination and verification have been accomplished, normal procedures for management of remains and release can be followed.

  15. Efficacy of liquid and foam decontamination technologies for chemical warfare agents on indoor surfaces.

    Science.gov (United States)

    Love, Adam H; Bailey, Christopher G; Hanna, M Leslie; Hok, Saphon; Vu, Alex K; Reutter, Dennis J; Raber, Ellen

    2011-11-30

    Bench-scale testing was used to evaluate the efficacy of four decontamination formulations on typical indoor surfaces following exposure to the liquid chemical warfare agents sarin (GB), soman (GD), sulfur mustard (HD), and VX. Residual surface contamination on coupons was periodically measured for up to 24h after applying one of four selected decontamination technologies [0.5% bleach solution with trisodium phosphate, Allen Vanguard Surface Decontamination Foam (SDF™), U.S. military Decon Green™, and Modec Inc. and EnviroFoam Technologies Sandia Decontamination Foam (DF-200)]. All decontamination technologies tested, except for the bleach solution, performed well on nonporous and nonpermeable glass and stainless-steel surfaces. However, chemical agent residual contamination typically remained on porous and permeable surfaces, especially for the more persistent agents, HD and VX. Solvent-based Decon Green™ performed better than aqueous-based bleach or foams on polymeric surfaces, possibly because the solvent is able to penetrate the polymer matrix. Bleach and foams out-performed Decon Green for penetrating the highly polar concrete surface. Results suggest that the different characteristics needed for an ideal and universal decontamination technology may be incompatible in a single formulation and a strategy for decontaminating a complex facility will require a range of technologies.

  16. Decontamination of viable Streptococcus mutans from orthodontic tungsten carbide debonding burs. An in vitro microbiological study.

    Science.gov (United States)

    Sheriteh, Zahra; Hassan, Tasnim; Sherriff, Martyn; Cobourne, Martyn; Cobourne, Martin; Riley, Peter

    2010-09-01

    To investigate the effectiveness of currently recommended decontamination procedures on tungsten carbide debonding burs (TCDBs). In vitro microbiological study. St George's Hospital NHS Trust, UK. A total of 240 extracted tooth surfaces were bonded with orthodontic brackets, debonded to leave residual composite and artificially contaminated with Streptococcus mutans. Sterilized TCDBs in a slow handpiece were used to remove this composite before random allocation into one of six different decontamination groups of 40 burs each. These included a control group that was not decontaminated and a further five that underwent different methods of presterilization cleaning within the decontamination process (none, manual, ultrasonic, washer disinfector and enzyme soak) followed by sterilization in a vacuum phase autoclave at 134 degrees C for 3 min. The burs were placed in brain heart infusion (BHI) broths, incubated for 48 h. Following this the broths were inspected for turbidity and microbiological analysis was carried out to detect viable bacterial growth. Data were analysed using the Kruskal-Wallis test for single ordered data. S. mutans was recovered from 39 out of 40 burs in the control group and no burs from the decontamination groups, which was statistically significant (P = 0.001). No differences were found between decontamination groups (P = 0.271). However, skin flora contamination was noted in 17 broths. The five methods of decontaminating TCDBs investigated in this study were effective in removing viable S. mutans. Other investigations are required to determine if TCDBs can be successfully cleaned of blood and protein residue prior reuse.

  17. Assessment of Environmental Contamination and Environmental Decontamination Practices within an Ebola Holding Unit, Freetown, Sierra Leone.

    Science.gov (United States)

    Youkee, Daniel; Brown, Colin S; Lilburn, Paul; Shetty, Nandini; Brooks, Tim; Simpson, Andrew; Bentley, Neil; Lado, Marta; Kamara, Thaim B; Walker, Naomi F; Johnson, Oliver

    2015-01-01

    Evidence to inform decontamination practices at Ebola holding units (EHUs) and treatment centres is lacking. We conducted an audit of decontamination procedures inside Connaught Hospital EHU in Freetown, Sierra Leone, by assessing environmental swab specimens for evidence of contamination with Ebola virus by RT-PCR. Swabs were collected following discharge of Ebola Virus Disease (EVD) patients before and after routine decontamination. Prior to decontamination, Ebola virus RNA was detected within a limited area at all bedside sites tested, but not at any sites distant to the bedside. Following decontamination, few areas contained detectable Ebola virus RNA. In areas beneath the bed there was evidence of transfer of Ebola virus material during cleaning. Retraining of cleaning staff reduced evidence of environmental contamination after decontamination. Current decontamination procedures appear to be effective in eradicating persistence of viral RNA. This study supports the use of viral swabs to assess Ebola viral contamination within the clinical setting. We recommend that regular refresher training of cleaning staff and audit of environmental contamination become standard practice at all Ebola care facilities during EVD outbreaks.

  18. Decontamination Experiments on Intact Pig Skin Contaminated with Beta-Gamma- Emitting Nuclides

    Energy Technology Data Exchange (ETDEWEB)

    Edvardsson, K.A.; Hagsgaard, S. [AB Atomenergi, Nykoeping (Sweden); Swensson, A. [Dept. of Occupational Medicine, Karolinska Sjukhuset, Stockholm (Sweden)

    1966-11-15

    A number of decontamination experiments have been performed on intact pig skin. In most of the experiments NaI-131 in water solution has been utilized because this nuclide is widely used within the Studsvik research establishment, is easy to detect and relatively harmless, and is practical to use in these experiments. Among the {beta} {gamma}-nuclides studied 1-131 has furthermore proved to be the one most difficult to remove from the skin. The following conclusions and recommendations regarding the decontamination of skin are therefore valid primarily for iodine in the form of Nal, but are probably also applicable to many other {beta} {gamma}-nuclides. a) A prolonged interval between contamination and decontamination has a negative effect on the result of the decontamination. Therefore start decontamination as soon as possible after the contamination. b) Soap and water has proved to be the most suitable decontamination agent. A number of other agents have appeared to be harmful to the skin. Therefore, first of all use only soap and water in connection with gentle rubbing. c) No clear connection between the temperature of the water for washing and the result of the decontamination has been demonstrated. d) Skin not degreased before the contamination seems to be somewhat easier to decontaminate than degreased skin, particularly if the activity has been on the skin for a long time. Therefore do not remove the sebum of the skin when engaged on radioactive work involving contamination risks. e) Irrigation of the contaminated surface with a solution containing the corresponding inactive ions or ordinary water in large quantities may considerably decrease the skin contamination. f) In radioactive work of long duration involving high risks of contamination prophylactic measures in the form of a protective substance ('invisible glove'), type Kerodex, may make decontamination easier.

  19. The restoration project : decontamination of facilities from chemical, biological and radiological contamination after terrorist action

    Energy Technology Data Exchange (ETDEWEB)

    Fingas, M.; Volchek, K.; Thouin, G.; Harrison, S.; Kuang, W. [Environment Canada, Ottawa, ON (Canada). Emergencies Science Div; Velicogna, D.; Hornof, M.; Punt, M. [SAIC Canada, Ottawa, ON (Canada); Payette, P.; Duncan, L.; Best, M.; Krishnan; Wagener, S.; Bernard, K.; Majcher, M. [Public Health Agency of Canada, Ottawa, ON (Canada); Cousins, T.; Jones, T. [Defence Research and Development Canada, Ottawa, ON (Canada)

    2005-07-01

    Bioterrorism poses a real threat to the public health and national security, and the restoration of affected facilities after a chemical, biological or radiological attack is a major concern. This paper reviewed aspects of a project conducted to collect information, test and validate procedures for site restoration after a terrorist attack. The project began with a review of existing technology and then examined new technologies. Restoration included pickup, neutralization, decontamination, removal and final destruction and deposition of contaminants as well as cleaning and neutralization of material and contaminated waste from decontamination. The project was also intended to test existing concepts and develop new ideas. Laboratory scale experiments consisted of testing, using standard laboratory techniques. Radiation decontamination consisted of removal and concentration of the radioisotopes from removal fluid. General restoration guidelines were provided, as well as details of factors considered important in specific applications, including growth conditions and phases of microorganisms in biological decontamination, or the presence of inhibitors or scavengers in chemical decontamination. Various agents were proposed that were considered to have broad spectrum capability. Test surrogates for anthrax were discussed. The feasibility of enhanced oxidation processes was examined in relation to the destruction of organophosphorus, organochlorine and carbamate pesticides. The goal was to identify a process for the treatment of surfaces contaminated with pesticides. Tests included removal from carpet, porous ceiling tile, steel plates, and floor tiles. General radiation contamination procedures and techniques were reviewed, as well as radiological decontamination waste treatment. It was concluded that there is no single decontamination technique applicable for all contaminants, and decontamination methods depend on economic, social and health factors. The amount of

  20. Innovative surface decontamination using a manipulator-deployed laser system

    Energy Technology Data Exchange (ETDEWEB)

    Bremmer, J.; Gentes, S. [Karlsruhe Institute of Technology (KIT), Karlsruhe (Germany). Inst. for Technology and Management in Construction Technology and Management for the Decommissioning of Nuclear Facilities; Littwin, R.; Hurtado, A.; Lippmann, W. [Dresden Univ. of Technology (TUD) (Germany). Chair of Hydrogen Technology and Nuclear Power Engineering

    2010-05-15

    The successful decommissioning and dismantlement of nuclear facilities requires a great number and variety of processes and actions. These include, inter alia, the qualified decontamination of surfaces. The associated tasks are manifold, ranging from simple cleaning to complete surface ablation. The latter is particularly challenging due to the multitude of surfaces in nuclear facilities which, to complicate things further, are made of the most diverse materials. Consequently, besides pure surfaces of concrete, plaster or masonry, it is also necessary to ablate coatings such as protective paints. These can be found both on mineral and metallic constructional components. A crucial factor in surface decontamination work is the effectiveness and economic efficiency of the methods used. The same applies to the avoidance of cross contamination and secondary waste. Only few of the currently available processes fully meet all these criteria and are suited for this kind of task. Due to the increasing number of decommissioning projects in Germany and the small number of processes available to accomplish them, there is a rising demand for suitable and efficient decommissioning systems. An innovative system for manipulator-controlled laser ablation of surfaces that fully meets these criteria is currently being developed under the research project MANOLA (manipulatorgesteuerter Abtrag von Oberflaechen durch Lasertechnologie = manipulator-controlled laser ablation of surfaces), a joint project of the Chair of Hydrogen Technology and Power Engineering of the Dresden University of Technology and the Chair of Technology and Management of the Decommissioning of Nuclear Facilities at the Karlsruhe Institute of Technology (KIT), funded by the German Federal Ministry of Education and Research (BMBF). The objective of this research project is to ablate contaminated surfaces by means of a manipulator-deployed laser head. It was shown by numerous experiments in the preceding research

  1. Decontamination of Surfaces Exposed to Carbonbased Nanotubes and Nanomaterials

    Science.gov (United States)

    Karimi, Zahra

    Contamination of surfaces by nanomaterials can happen due to accidental spillage and release or gradual accumulation during processing or handling. Considering the increasingly wide use of nanomaterials in industry and research labs and also taking into account the diversity of physical and chemical properties of different nanomaterials (such as solubility, aggregation/agglomeration, and surface reactivity), there is a pressing need to define reliable nanomaterial-specific decontamination guidelines. In this project, we propose and investigate a potential method for surface decontamination of carbon-based nanomaterials using solvent cleaning and wipes. The results show that the surfactant-assisted removal efficiencies of multi-walled carbon nanotubes, single walled carbon nantubes and single walled carbon nano-horns from silicon wafers through wiping is greater than 95%, 90% and 78%, respectively. The need for further studies to understand the mechanisms of nanomaterial removal from surfaces and development of standard techniques for surface decontamination of nanomaterials is highlighted. Another phase of experiments were performed to examine the efficiency of surfactants to remove multi-walled carbon nanotubes (MWCNTs) from silicon substrates with nano and microscaled features. In the first set of experiments, nanoscale features were induced on silicon wafers using SF6 and O2 plasma. Atomic force microscopy (AFM) was used to observe the surface topology and roughness. In the second set, well-defined microscale topological features were induced on silicon wafers using photo lithography and plasma etching. The etching time was varied to create semi-ellipsoidal pits with average diameter and height of ~ 7-9 microm, and ~ 1-3 microm, respectively. MWCNTs in the form of liquid solution were deposited on the surface of silicon wafers using the spin coating process. For the cleaning process, the contaminated surfaces were first sprayed with different types of surfactant

  2. Decontamination Characteristics of Stainless Steel Surface Contaminated with Cs{sup +} Ion by Light Ablation

    Energy Technology Data Exchange (ETDEWEB)

    Baigalmaa, Byambatseren; Won, Hui-Jun; Moon, Jei-Kwon; Jung, Chong-Hun [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Hyun, Jae-Hyuk [Chungnam National University, Daejeon (Korea, Republic of)

    2008-05-15

    The characteristics of decontamination method by light ablation are the remote operation, a short application time, and the high removal efficiency. Furthermore, the generation of the secondary waste is negligible. The radioactivity of hot cells in DFDF (Dupic Fuel Development Facility) is presumed to be very high and the predominant radionuclide is Cs-137. A series of laser decontamination studies by the fabricated Qswitched Nd-YAG laser system were performed on the stainless steel specimens artificially contaminated with Cs{sup +} ion. Decontamination characteristics of the stainless steel were analyzed by SEM and EPMA.

  3. The pharmacological activity of medical herbs after microbiological decontamination by irradiation

    Science.gov (United States)

    Owczarczyk, H. B.; Migdał, W.; K ȩdzia, B.

    2000-03-01

    In the Institute of Nuclear Chemistry and Technology research on microbiological decontamination of medicinal herbs by irradiation has been carried out since 1996. It was shown that using ionizing radiation (a dose of 10 kGy) can obtain satisfactory results of microbiological decontamination of these products. The content of essential biologically active substances such as essential oils, flavonoids, glycosides, anthocyans, antra-compounds, poliphenoloacids, triterpene saponins, oleanosides and plants mucus did not change significantly after irradiation. Pharmacological activity of medicinal herbs has been found satisfactory after microbiological decontamination by irradiation.

  4. Electromagnetic mixed waste processing system for asbestos decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Kasevich, R.S. [KAI Technologies, Inc., Portsmouth, NH (United States); Vaux, W.G. [Westinghouse Electric Corp., Pittsburgh, PA (United States); Nocito, T. [Ohio DSI Corp., New York (United States)

    1995-10-01

    DOE sites contain a broad spectrum of asbestos materials (cloth, pipe lagging, sprayed insulation and other substances) which are contaminated with a combination of hazardous and radioactive wastes due to its use during the development of the U.S. nuclear weapons complex. These wastes consist of cutting oils, lubricants, solvents, PCB`s, heavy metals and radioactive contaminants. The radioactive contaminants are the activation, decay and fission products of DOE operations. The asbestos must be converted by removing and separating the hazardous and radioactive materials to prevent the formation of mixed wastes and to allow for both sanitary disposal and effective decontamination. Currently, no technology exists that can meet these sanitary and other objectives.

  5. Composition suitable for decontaminating a porous surface contaminated with cesium

    Science.gov (United States)

    Kaminski, Michael D.; Finck, Martha R.; Mertz, Carol J.

    2010-06-15

    A method of decontaminating porous surfaces contaminated with water soluble radionuclides by contacting the contaminated porous surfaces with an ionic solution capable of solubilizing radionuclides present in the porous surfaces followed by contacting the solubilized radionuclides with a gel containing a radionuclide chelator to bind the radionuclides to the gel, and physically removing the gel from the porous surfaces. A dry mix is also disclosed of a cross-linked ionic polymer salt, a linear ionic polymer salt, a radionuclide chelator, and a gel formation controller present in the range of from 0% to about 40% by weight of the dry mix, wherein the ionic polymer salts are granular and the non cross-linked ionic polymer salt is present as a minor constituent.

  6. Natural coagulation for the decontamination of industrial effluents

    Directory of Open Access Journals (Sweden)

    Carlos Banchón

    2016-12-01

    Full Text Available Industrial and agricultural pollution has generated undoubtedly a high environmental impact on the natural resources of our planet. Deficiencies in the provision of water for human consumption due to pollution from natural sources are expected. In response to this, the application of iron and aluminum coagulants are the first choice for wastewater treatment. However, the abundant use of aluminum is subject of discussion because of the potential impact on humans. Therefore, this article highlights the latest advances in the field of natural coagulation, an ancestral technology used for water decontamination. Its proven effectiveness is based on electrokinetic destabilization mechanisms that remove turbidity up to 99%. Experimental evidence agrees that concentrations of tannins and mucilages allow the remediation of effluents from chemical industries such as textile and tanneries.

  7. [Efficacy of selective digestive decontamination (SDD) for severe acute pancreatitis].

    Science.gov (United States)

    Kitamura, Nobuya; Hirano, Takeshi; Moriguchi, Takeshi; Hirasawa, Hiroyuki; Ohtani, Shunsuke

    2004-11-01

    Bacterial translocation (BT) is involved in the development of pancreatic infection in severe acute pancreatitis (SAP) and influences the prognosis. We should suppress BT to prevent pancreatic infection and improve survival rate. Selective digestive decontamination (SDD) is rational treatment. We should aim at effective SDD, ensuring the following 4 points: (1) enteral antimicrobials, in combination with, (2) parenteral antibiotics given immediately on admission, (3) hand hygiene, (4) surveillance cultures of throat and rectum. Starting enteral feeding as soon as possible and avoiding long-term SDD is useful for maintaining the defenses of the intestinal mucosa and preventing emergence of resistant bacteria. We used glutamine and dietary fiber besides SDD and were able to reduce pancreatic infection.

  8. OIL DECONTAMINATION OF BOTTOM SEDIMENTS EXPERIMENTAL WORK RESULTS

    Directory of Open Access Journals (Sweden)

    Lushnikov Sergey V.

    2006-08-01

    Full Text Available This article presents the results of experimental work during 2004-2005 on oil decontamination of bottom sediments of Lake Schuchye, situated in the Komi Republic (Northern Russia. The cause of thecontamination were huge oil spills occurred after a series of accidental ruptures on the Harjaga-Usinsk and Vozej-Usinsk oil-pipe lines in 1994. Flotation technology was used for the cleaning of bottom sediments.157 tons of crude oil were removed during the course of 2-year experimental work from an area of 4,1 ha.The content of aliphatic and alicyclic oil hydrocarbons was reduced from 53,3 g/kg to 2,2 g/kg, on average.Hydrobiological investigations revealed that bottom sediments started to be inhabited by benthos organisms, dominantly Oligochaeta. Besides Oligochaeta, Chironomidae maggots and Bivalvia were detected. Theappearance of Macrozoobenthos organisms can serve as a bioindicator of water quality.

  9. Nanomaterials for Electrochemical Sensing and Decontamination of Pesticides.

    Science.gov (United States)

    Viswanathan, S; Manisankar, P

    2015-09-01

    We are all aware of growing environmental concerns, and the need to provide new and improved means for maintaining a healthy environment. Pesticides are the only toxic chemicals released intentionally into the environment to kill living organisms. Pesticide detection and destruction has become a very important and inevitable area of research because of the rapid expansion of agriculture and stringent environmental protection acts. Electrochemistry offers promising approaches for the determination and destruction of pollutants. The interaction of nanotechnology opens the possibility for a wide variety of chemical and biological research topics and day-to-day applications at the molecular and cellular level. Nanotechnology has allowed introducing novel strategies in sensors and biosensor research. Recently researchers have become increasingly interested in nanomaterial assisted electrochemical techniques. This review emphasizes the recent developments of electrochemical methods combined with nanotechnology for sensing and decontamination of pesticides.

  10. Contaminated concrete: Occurrence and emerging technologies for DOE decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Dickerson, K.S.; Wilson-Nichols, M.J. [Oak Ridge National Lab., Grand Junction, CO (United States); Morris, M.I. [Oak Ridge National Lab., TN (United States)

    1995-08-01

    The goals of the Facility Deactivation, Decommissioning, and Material Disposition Focus Area, sponsored by the US Department of Energy (DOE) Office of Technology Development, are to select, demonstrate, test, and evaluate an integrated set of technologies tailored to provide a complete solution to specific problems posed by deactivation, decontamination, and decommissioning, (D&D). In response to these goals, technical task plan (TTP) OR152002, entitled Accelerated Testing of Concrete Decontamination Methods, was submitted by Oak Ridge National Laboratory. This report describes the results from the initial project tasks, which focused on the nature and extent of contaminated concrete, emerging candidate technologies, and matching of emerging technologies to concrete problems. Existing information was used to describe the nature and extent of contamination (technology logic diagrams, data bases, and the open literature). To supplement this information, personnel at various DOE sites were interviewed, providing a broad perspective of concrete contamination. Because characterization is in the initial stage at many sites, complete information is not available. Assimilation of available information into one location is helpful in identifying potential areas of concern in the future. The most frequently occurring radiological contaminants within the DOE complex are {sup 137}Cs, {sup 238}U (and it daughters), and {sup 60}Co, followed closely by {sup 90}Sr and tritium, which account for {minus}30% of the total occurrence. Twenty-four percent of the contaminants were listed as unknown, indicating a lack of characterization information, and 24% were listed as other contaminants (over 100 isotopes) with less than 1% occurrence per isotope.

  11. Hair decontamination procedure prior to multi-class pesticide analysis.

    Science.gov (United States)

    Duca, Radu-Corneliu; Hardy, Emilie; Salquèbre, Guillaume; Appenzeller, Brice M R

    2014-06-01

    Although increasing interest is being observed in hair analysis for the biomonitoring of human exposure to pesticides, some limitations still have to be addressed for optimum use of this matrix in that specific context. One main possible issue concerns the need to differentiate chemicals biologically incorporated into hair from those externally deposited on hair surface from contaminated air or dust. The present study focuses on the development of a washing procedure for the decontamination of hair before analysis of pesticides from different chemical classes. For this purpose, three different procedures of artificial contamination (with silica, cellulose, and aqueous solution) were used to simulate pesticides deposition on hair surface. Several washing solvents (four organic: acetone, dichloromethane, methanol, acetonitrile; and four aqueous: water, phosphate buffer, shampoo, sodium dodecylsulfate) were evaluated for their capacity to remove artificially deposited pesticides from hair surface. The most effective washing solvents were sodium dodecylsulfate and methanol for aqueous and organic solvents, respectively. Moreover, after a first washing with sodium dodecylsulfate or methanol, the majority of externally deposited pesticides was removed and a steady-state was reached since significantly lower amounts were removed by additional second and third washings. Finally, the effectiveness of a decontamination procedure comprising washing with sodium dodecylsulfate and methanol was successively demonstrated. In parallel, it was determined that the final procedure did not affect the chemicals biologically incorporated, as hair strands naturally containing pesticides were used. Such a procedure appears to remove in one-shot the fraction of chemicals located on hair surface and does not require repeated washing steps.

  12. Cold atmospheric plasma - A new technology for spacecraft component decontamination

    Science.gov (United States)

    Shimizu, Satoshi; Barczyk, Simon; Rettberg, Petra; Shimizu, Tetsuji; Klaempfl, Tobias; Zimmermann, Julia L.; Hoeschen, Till; Linsmeier, Christian; Weber, Peter; Morfill, Gregor E.; Thomas, Hubertus M.

    2014-01-01

    Cold atmospheric plasma (CAP) based on the Surface Micro-Discharge (SMD) technology was investigated for inactivation of different bacteria and endospores. The used technique was developed to serve as an alternative method for the decontamination of spacecraft components based on the COSPAR planetary protection policy where currently the dry heat microbial reduction method is the only applicable way to satisfy the required demands. However it is known, that dry heat can thermally damage sophisticated components installed on the device. Therefore, the development of a low temperature sterilization system is one of the high priority issues for upcoming space missions in the extraterrestrial field. In the study presented here, the vegetative bacteria Escherichia coli and Deinococcus radiodurans and several types of bacterial endospores - including Bacillus atrophaeus, Bacillus safensis, Bacillus megaterium, Bacillus megaterium 2c1 and Bacillus thuringiensis E24 - were inactivated by exposing them indirectly i.e. only to the reactive gases produced by the SMD electrode at room temperature. The results showed a 5 log inactivation for E. coli after 10 min of exposure. In contrast D. radiodurans proved to be more resistant resulting in a reduction of 3 log after exposure of 30 min. More than 6 log reductions were achieved for B. safensis, B. megaterium and B. megaterium 2c1 after 90 min of exposure. Furthermore the applicability of the used CAP system for spacecraft decontamination according to the planetary protection policy was investigated. This included also the investigation of the inactivation homogeneity by the plasma gas, the control of the temperature at the area of interest, the measurement of the O3 density in the treatment region and the detailed investigation of the effects of the exposure on different materials.

  13. Bagworm bags as portable armour against invertebrate predators

    OpenAIRE

    Shinji Sugiura

    2016-01-01

    Some animals have evolved the use of environmental materials as “portable armour” against natural enemies. Portable bags that bagworm larvae (Lepidoptera: Psychidae) construct using their own silk and plant parts are generally believed to play an important role as a physical barrier against natural enemies. However, no experimental studies have tested the importance of bags as portable armour against predators. To clarify the defensive function, I studied the bagworm Eumeta minuscula and a po...

  14. Portability and the National Energy Software Center

    Energy Technology Data Exchange (ETDEWEB)

    Butler, M K

    1978-01-01

    The software portability problem is examined from the viewpoint of experience gained in the operation of a software exchange and information center. First, the factors contributing to the program interchange to date are identified, then major problem areas remaining are noted. The import of the development of programing language and documentation standards is noted, and the program packaging procedures and dissemination practices employed by the Center to facilitate successful software transport are described. Organization, or installation, dependencies of the computing environment, often hidden from the program author, and data interchange complexities are seen as today's primary issues, with dedicated processors and network communications offering an alternative solution.

  15. Portable Battery Charger Berbasis Sel Surya

    OpenAIRE

    Budhi Anto; Edy Hamdani; Rizki Abdullah

    2014-01-01

    A type of solar battery charger is introduced in this paper. This equipment functions as a medium size rechargeable battery that is needed to move culinary merchants and coastal fishermen living in area which is not supplied by electrical networks. The equipment consists of solar module mounted onto portable mechanical construction, a 12-V 7.5-Ah lead acid battery and charge controller. Solar module charges the battery through charge controller and then the battery can be discharged to power ...

  16. Portability and the National Energy Software Center

    Science.gov (United States)

    Butler, M. K.

    1978-01-01

    The software portability problem is examined from the viewpoint of experience gained in the operation of a software exchange and information center. First, the factors contributing to the program interchange to date are identified, then major problem areas remaining are noted. The import of the development of programming language and documentation standards is noted, and the program packaging procedures and dissemination practices employed by the Center to facilitate successful software transport are described. Organization, or installation, dependencies of the computing environment, often hidden from the program author, and data interchange complexities are seen as today's primary issues with dedicated processors and network communications offering an alternative solution.

  17. High volume, multiple use, portable precipitator

    Science.gov (United States)

    Carlson, Duane C.

    2011-10-25

    A portable high air volume electrostatic collection precipitator for analyzing air is provided which is a relatively small, self-contained device. The device has a collection electrode adapted to carry a variety of collecting media. An air intake is provided such that air to be analyzed flows through an ionization section with a transversely positioned ionization wire to ionize analytes in the air, and then flows over the collection electrode where ionized analytes are collected. Air flow is maintained at but below turbulent flow, Ionizable constituents in the air are ionized, attracted to the collection electrode, and precipitated in the selected medium which can be removed for analysis.

  18. Portable crushers resolve frozen coal problem

    Energy Technology Data Exchange (ETDEWEB)

    Massa, P.; Fuller, L.; Buckley, T. [Public Services of Indiana (PSI), IN (United States)

    2001-11-01

    In 2002, PSI contracted XMS Equipment to design a pair of modularized and portable crushers to overcome the problem of frozen coal during winter months. The rollers of the crusher can be removed during non-winter months, reducing wear. The article describes the design, construction and installation of the system which takes care of the frozen coal in the hoppers and the coal feed systems in the 1000 W Cayuga plant and overcomes the problem of coal freezing in the reclaim hoppers and the open coal storage areas. 4 figs.

  19. Development of a Portable Water Quality Analyzer

    Directory of Open Access Journals (Sweden)

    Germán COMINA

    2010-08-01

    Full Text Available A portable water analyzer based on a voltammetric electronic tongue has been developed. The system uses an electrochemical cell with two working electrodes as sensors, a computer controlled potentiostat, and software based on multivariate data analysis for pattern recognition. The system is suitable to differentiate laboratory made and real in-situ river water samples contaminated with different amounts of Escherichia coli. This bacteria is not only one of the main indicators for water quality, but also a main concern for public health, affecting especially people living in high-burden, resource-limiting settings.

  20. Portable Biomarker Detection with Magnetic Nanotags.

    Science.gov (United States)

    Hall, Drew A; Wang, Shan X; Murmann, Boris; Gaster, Richard S

    2010-08-03

    This paper presents a hand-held, portable biosensor platform for quantitative biomarker measurement. By combining magnetic nanoparticle (MNP) tags with giant magnetoresistive (GMR) spin-valve sensors, the hand-held platform achieves highly sensitive (picomolar) and specific biomarker detection in less than 20 minutes. The rapid analysis and potential low cost make this technology ideal for point-of-care (POC) diagnostics. Furthermore, this platform is able to detect multiple biomarkers simultaneously in a single assay, creating a promising diagnostic tool for a vast number of applications.

  1. Security risks arising from portable storage devices

    CSIR Research Space (South Africa)

    Molotsi, K

    2012-10-01

    Full Text Available ? To identify and provide security countermeasures to help organisations and users to address the security risks from PSDs DEFINITION OF PORTABLE STORAGE DEVICES A PSD can be defined as: ? A small, lightweight device that is capable of storing... stream_source_info Molotsi_2012.pdf.txt stream_content_type text/plain stream_size 4841 Content-Encoding ISO-8859-1 stream_name Molotsi_2012.pdf.txt Content-Type text/plain; charset=ISO-8859-1 Security risks arising from...

  2. 33 CFR 127.603 - Portable fire extinguishers.

    Science.gov (United States)

    2010-07-01

    ... (CONTINUED) WATERFRONT FACILITIES WATERFRONT FACILITIES HANDLING LIQUEFIED NATURAL GAS AND LIQUEFIED HAZARDOUS GAS Waterfront Facilities Handling Liquefied Natural Gas Firefighting § 127.603 Portable...

  3. Selective oropharyngeal decontamination versus selective digestive decontamination in critically ill patients: a meta-analysis of randomized controlled trials

    Directory of Open Access Journals (Sweden)

    Zhao D

    2015-07-01

    Full Text Available Di Zhao,1,* Jian Song,2,* Xuan Gao,3 Fei Gao,4 Yupeng Wu,2 Yingying Lu,5 Kai Hou1 1Department of Neurosurgery, The First Hospital of Hebei Medical University, 2Department of Neurosurgery, 3Department of Neurology, The Second Hospital of Hebei Medical University, 4Hebei Provincial Procurement Centers for Medical Drugs and Devices, 5Department of Neurosurgery, The Second Hospital of Hebei Medical University, Shijiazhuang People’s Republic of China *These authors contributed equally to this work Background: Selective digestive decontamination (SDD and selective oropharyngeal decontamination (SOD are associated with reduced mortality and infection rates among patients in intensive care units (ICUs; however, whether SOD has a superior effect than SDD remains uncertain. Hence, we conducted a meta-analysis of randomized controlled trials (RCTs to compare SOD with SDD in terms of clinical outcomes and antimicrobial resistance rates in patients who were critically ill. Methods: RCTs published in PubMed, Embase, and Web of Science were systematically reviewed to compare the effects of SOD and SDD in patients who were critically ill. Outcomes included day-28 mortality, length of ICU stay, length of hospital stay, duration of mechanical ventilation, ICU-acquired bacteremia, and prevalence of antibiotic-resistant Gram-negative bacteria. Results were expressed as risk ratio (RR with 95% confidence intervals (CIs, and weighted mean differences (WMDs with 95% CIs. Pooled estimates were performed using a fixed-effects model or random-effects model, depending on the heterogeneity among studies. Results: A total of four RCTs involving 23,822 patients met the inclusion criteria and were included in this meta-analysis. Among patients whose admitting specialty was surgery, cardiothoracic surgery (57.3% and neurosurgery (29.7% were the two main types of surgery being performed. Pooled results showed that SOD had similar effects as SDD in day-28 mortality (RR =1

  4. How Clean is Safe? Improving the Effectiveness of Decontamination of Structures and People Following Chemical and Biological Incidents

    Energy Technology Data Exchange (ETDEWEB)

    Vogt (Sorensen), B.M.

    2003-04-03

    This report describes a U.S. Department of Energy, (DOE) Chemical and Biological National Security Program project that sought to establish what is known about decontamination of structures, objects, and people following an exposure to chemical or biological materials. Specifically we sought to identify the procedures and protocols used to determine when and how people or buildings are considered ''clean'' following decontamination. To fulfill this objective, the study systematically examined reported decontamination experiences to determine what procedures and protocols are currently employed for decontamination, the timeframe involved to initiate and complete the decontamination process, how the contaminants were identified, the factors determining when people were (or were not) decontaminated, the problems encountered during the decontamination process, how response efforts of agencies were coordinated, and the perceived social psychological effects on people who were decontaminated or who participated in the decontamination process. Findings and recommendations from the study are intended to aid decision-making and to improve the basis for determining appropriate decontamination protocols for recovery planners and policy makers for responding to chemical and biological events.

  5. Change in tensile properties of neoprene and nitrile gloves after repeated exposures to acetone and thermal decontamination.

    Science.gov (United States)

    Gao, Pengfei; Tomasovic, Beth

    2005-11-01

    This study investigated the change in tensile properties of neoprene and nitrile gloves after repeated cycles of exposure to acetone, followed by thermal decontamination. The glove was exposed to acetone (outer surface in contact with chemical), subjected to thermal decontamination, and tested for the tensile strength and the ultimate elongation. Thermal decontamination was carried out inside an oven for 16 hours at 100 degrees C. The exposure/decontamination procedure was repeated for a maximum of 10 cycles. For neoprene versus acetone, the mean tensile strength consistently decreased after each exposure/decontamination cycle. Multiple comparisons indicated that the mean tensile strengths between the new swatches and each exposure/decontamination group were significantly different (p 0.05). The mean tensile strength for the new swatches was 37.1 MPa and the mean tensile strength after nine exposure/decontamination cycles was 36.0 MPa, with a loss less than 3%. The largest single cycle loss for ultimate elongation occurred during the first exposure/decontamination cycle for both glove materials. In our previous study, decisions regarding the effectiveness of the decontamination process were based on having no discernible change in the breakthrough time and steady-state permeation rate. The results of this study indicate that the effectiveness of the decontamination process cannot be based on permeation parameters alone but must also take into account the change in physical properties.

  6. A DECONTAMINATION PROCESS FOR METAL SCRAPS FROM THE DECOMMISSIONING OF TRR

    Energy Technology Data Exchange (ETDEWEB)

    Wei, T.Y.; Gan, J.S.; Lin, K.M.; Chung, Z.J.

    2003-02-27

    A decontamination facility including surface condition categorizing, blasting, chemical/electrochemical cleaning, very low radioactivity measuring, and melting, is being established at INER. The facility will go into operation by the end of 2004. The main purpose is to clean the dismantled metal wastes from the decommissioning of Taiwan Research Reactor (TRR). The pilot test shows that over 70% of low level metal waste can be decontaminated to very low activity and can be categorized as BRC (below regulatory concern) waste. All the chemical decontamination technologies applied are developed by INER. In order to reduce the secondary wastes, chemical reagents will be regenerated several times with a selective precipitation method. The exhausted chemical reagent will be solidified with INER's patented process. The total secondary waste is estimated about 0.1-0.3 wt.% of the original waste. This decontamination process is accessed to be economic and feasible.

  7. A study on decontamination and decommissioning of experimental DUPIC equipment at PIEF 9405 hot cell

    Energy Technology Data Exchange (ETDEWEB)

    Lee, H. H.; Park, J. J.; Shin, J. M.; Yang, M. S.; Lee, H. S.; Lee, E. P

    2000-09-01

    The characterization experiment for powder and sintered fuel had been performed using about 1 kg-U spent PWR fuel at No. 9405 hot-cell in PIEF(Post Irradiated Experiment Facility) since early in 1999. Currently, The experiments in PIEF have been completed. It is supposed to dismantle and decontaminate the installed equipment by the end of year 2000. Since all of DUPIC equipment in hot-cell are contaminated by high radioactive material, the decontamination and dismantlement must br performed remotely by M/S manipulator. During the radioactive waste packing and transportation, the reduction method of radiation exposure has to be considered. Firstly, This report describes the basic plan for dismantlement/decontamination of the characterization equipment(power and sintered fuel). And methods of measurement/packing/ transportation, method of dismantlement/decontamination of the experimental apparatus and the reduction method of radiation dose exposure, etc. are explained in order.

  8. [Effective cleansing and decontamination of the base of an injury; reduction in time for cicatrization].

    Science.gov (United States)

    González, Juan Antonio Jiménez; Resúa, María Rosa Pérez

    2008-02-01

    The authors evaluate a solution and a gel composed of undecylenate prophyl betaine and polyhexanide recommended for cleansing and decontaminating injuries, without having any cytotoxic, irritating or sensibility effect which favors and stimulates the natural cicatrization process.

  9. Controlled clinical trial of selective decontamination for the treatment of severe acute pancreatitis

    NARCIS (Netherlands)

    E.J.T. Luiten (Ernest); W.C.J. Hop (Wim); J.F. Lange (Johan); H.A. Bruining (Hajo)

    1995-01-01

    textabstractOBJECTIVE: A randomized, controlled, multicenter trial was undertaken in 102 patients with objective evidence of severe acute pancreatitis to evaluate whether selective decontamination reduces mortality. SUMMARY BACKGROUND DATA: Secondary pancreatic infectio

  10. Assessing microbial decontamination of indoor air with particular focus on human pathogenic viruses.

    Science.gov (United States)

    Duchaine, Caroline

    2016-09-01

    Transmission of bacterial, fungal, and viral pathogens is of primary importance in public and occupational health and infection control. Although several standardized protocols have been proposed to target microbes on fomites through surface decontamination, use of microbicidal agents, and cleaning processes, only limited guidance is available on microbial decontamination of indoor air to reduce the risk of pathogen transmission between individuals. This article reviews the salient aspects of airborne transmission of infectious agents, exposure assessment, in vitro assessment of microbicidal agents, and processes for air decontamination for infection prevention and control. Laboratory-scale testing (eg, rotating chambers, wind tunnels) and promising field-scale methodologies to decontaminate indoor air are also presented. The potential of bacteriophages as potential surrogates for the study of airborne human pathogenic viruses is also discussed.

  11. Oral decontamination with chlorhexidine reduces the incidence of ventilator-associated pneumonia.

    NARCIS (Netherlands)

    Koeman, M.; Ven, A.J.A.M. van der; Hak, E.; Joore, H.C.; Kaasjager, K.A.; Smet, A.G. de; Ramsay, G.; Dormans, T.P.J.; Aarts, L.P.H.J.; Bel, E.E. de; Hustinx, W.; Tweel, I. van de; Hoepelman, A.M.; Bonten, M.J.M.

    2006-01-01

    RATIONALE: Ventilator-associated pneumonia (VAP) is the most frequently occurring nosocomial infection associated with increased morbidity and mortality. Although oral decontamination with antibiotics reduces incidences of VAP, it is not recommended because of potential selection of antibiotic-resis

  12. Mass Casualty Decontamination in a Chemical or Radiological/ Nuclear Incident: Further Guiding Principles

    Science.gov (United States)

    Carter, Holly; Amlôt, Richard; Williams, Richard; Rubin, G. James; Drury, John

    2016-01-01

    This short report presents a response to an article written by Cibulsky et al. (2016). The paper by Cibulsky et al. presents a useful and timely overview of the evidence surrounding the technical and operational aspects of mass casualty decontamination. It identifies three priority targets for future research, the third of which is how casualties' needs can be met in ways that best support compliance with and effectiveness of casualty decontamination. While further investigation into behavioural, communication and privacy issues during mass decontamination is warranted, there is now a substantial body of research in this area which is not considered in detail in the succinct summary provided by Cibulsky et al. (2016). In this short report, we summarise the available evidence around likely public behaviour during mass decontamination, effective communication strategies, and potential issues resulting from a lack of privacy. Our intention is to help further focus the research needs in this area and highlight topics on which more research is needed.

  13. Controlled clinical trial of selective decontamination for the treatment of severe acute pancreatitis

    NARCIS (Netherlands)

    E.J.T. Luiten (Ernest); W.C.J. Hop (Wim); J.F. Lange (Johan); H.A. Bruining (Hajo)

    1995-01-01

    textabstractOBJECTIVE: A randomized, controlled, multicenter trial was undertaken in 102 patients with objective evidence of severe acute pancreatitis to evaluate whether selective decontamination reduces mortality. SUMMARY BACKGROUND DATA: Secondary pancreatic

  14. Technical Improvements to an Absorbing Supergel for Radiological Decontamination in Tropical Environments

    Energy Technology Data Exchange (ETDEWEB)

    Kaminski, Michael D. [Argonne National Lab. (ANL), Argonne, IL (United States); Mertz, Carol J. [Argonne National Lab. (ANL), Argonne, IL (United States); Kivenas, Nadia [Argonne National Lab. (ANL), Argonne, IL (United States); demmer, Rick [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-01-01

    Argonne National Laboratory (Argonne) developed a superabsorbing gel-based process (SuperGel) for the decontamination of cesium from concrete and other porous building materials. Here, we report on results that tested the gel decontamination technology on specific concrete and ceramic formulations from a coastal city in Southeast Asia, which may differ significantly from some U.S. sources. Results are given for the evaluation of americium and cesium sequestering agents that are commercially available at a reasonable cost; the evaluation of a new SuperGel formulation that combines the decontamination properties of cesium and americium; the variation of the contamination concentration to determine the effects on the decontamination factors with concrete, tile, and brick samples; and pilot-scale testing (0.02–0.09 m2 or 6–12 in. square coupons).

  15. A study on the decontamination of the gravels contaminated by uranium

    Energy Technology Data Exchange (ETDEWEB)

    Park, Ukryang; Kim, Gyenam; Kim, Seungsoo; Moon, Jaikwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-05-15

    The amount of gravels contaminated by uranium is usually about 10% of the contaminated soil. Since such contaminated gravels show different kinds and volumes, it would cost a considerable amount of money if they are to be disposed of without going through any special process. Also, there has not been any particular way or technology for processing the gravels contaminated by uranium. Therefore, various fundamental experiments and researches have been carried out for the decontamination of the gravels contaminated by uranium. Through such experiments and researches, it has been possible to obtain some significant results. The acid cleaning process, which is based on the application of the soil cleaning method, can be regarded as one of the major ways used for decontamination. When the gravels contaminated by uranium are cleaned as they are, most of them tend to show an extremely-low level of decontamination. Therefore, it could be said that the inside of each gravel is also contaminated by uranium. As a result, the gravels contaminated by uranium need to be crushed before being cleaned, which would result in a higher level of efficiency for decontamination compared to the previous way. Therefore, it is more effective to crush the subject gravels before cleaning them in terms of decontamination. However, such test results can only be applied to the gravels contaminated by an average level of uranium concentration. Regarding the gravels showing a higher level of uranium concentration than the average, it is still necessary to carry out more researches. Therefore, this study focused on the level of efficiency for decontamination after the contaminated gravels were crushed before being cleaned, in order to find a way to effectively dispose of the gravels contaminated by high-concentration uranium and secure a high level of efficiency for decontamination. In order to decontaminate the gravels which were contained in the soil contaminated by uranium and showed a higher

  16. How star women build portable skills.

    Science.gov (United States)

    Groysberg, Boris

    2008-02-01

    In May 2004, with the war for talent in high gear, Groysberg and colleagues from Harvard Business School wrote in these pages about the risks of hiring star performers away from competitors. After studying the fortunes of more than 1,000 star stock analysts, they found that when a star switched companies, not only did his performance plunge, so did the effectiveness of the group he joined and the market value of his new company. But further analysis of the data reveals that it's not that simple. In fact, one group of analysts reliably maintained star rankings even after changing employers: women. Unlike their male counterparts, female stars who switched firms performed just as well, in the aggregate, as those who stayed put. The 189 star women in the sample (18% of the star analysts studied) achieved a higher rank after switching firms than the men did. Why the discrepancy? First, says the author, the best female analysts appear to have built their franchises on portable, external relationships with clients and the companies they covered, rather than on relationships rooted within their firms. By contrast, male analysts built up greater firm- and team-specific human capital by investing more in the internal networks and unique capabilities and resources of their own companies. Second, women took greater care when assessing a prospective new employer. In this article, Groysberg explores the reasons behind the star women's portable performance.

  17. Portable Hybrid Powered Water Filtration Device

    Directory of Open Access Journals (Sweden)

    Maria Lourdes V. Balansay

    2015-08-01

    Full Text Available The existing water filtration device has features that can be developed to be more useful and functional during emergency situations. The project’s development has been aided by following provisions in PEC, NEC, NEMA and Philippine National Standard for Safe Drinking Water provide standards for the construction of the project. These standards protect both the prototype and the user. These also served as guide for the maintenance of every component. The design of the portable hybrid powered water filtration device shows that the project has more advanced features such as portability and the power supply used such as photovoltaic module solar cells and manually operated generator. This also shows its effectiveness and reliability based on the results of discharging test, water quality test and water production test. Based on analysis of the overall financial aspects, the machine can be profitable and the amount of revenue and operating cost will increase as years pass. Using the proper machine/ tools and methods of fabrication helps in easy assembly of the project. The materials and components used are cost effective and efficient. The best time for charging the battery using solar panel is 9:00 am onwards while the hand crank generator is too slow because the generated current is little. The water filtration device is very efficient regarding the operating hours and water production. The machine may have a great effect to society and economy in generation of clean available water at less cost.

  18. Portable fluorescence meter with reference backscattering channel

    Science.gov (United States)

    Kornilin, Dmitriy V.; Grishanov, Vladimir N.; Zakharov, Valery P.; Burkov, Dmitriy S.

    2016-09-01

    Methods based on fluorescence and backscattering are intensively used for determination of the advanced glycation end products (AGE) concentration in the biological tissues. There are strong correlation between the AGE concentration and the severity of such diseases like diabetes, coronary heart disease and renal failure. This fact can be used for diagnostic purposes in medical applications. Only few investigations in this area can be useful for development of portable and affordable in vivo AGE meter because the most of them are oriented on using spectrometers. In this study we describe the design and the results of tests on volunteers of portable fluorescence meter based on two photodiodes. One channel of such fluorimeter is used for measurement of the autofluorescence (AF) intensity, another one - for the intensity of elastically scattered radiation, which can be used as a reference. This reference channel is proposed for normalization of the skin autofluorescence signal to the human skin photo type. The fluorimeter, that was developed is relatively compact and does not contain any expensive optical and electronic components. The experimental results prove that proposed tool can be used for the AGE estimation in human skin.

  19. DOE Centers of Excellence Performance Portability Meeting

    Energy Technology Data Exchange (ETDEWEB)

    Neely, J. R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2016-04-21

    Performance portability is a phrase often used, but not well understood. The DOE is deploying systems at all of the major facilities across ASCR and ASC that are forcing application developers to confront head-on the challenges of running applications across these diverse systems. With GPU-based systems at the OLCF and LLNL, and Phi-based systems landing at NERSC, ACES (LANL/SNL), and the ALCF – the issue of performance portability is confronting the DOE mission like never before. A new best practice in the DOE is to include “Centers of Excellence” with each major procurement, with a goal of focusing efforts on preparing key applications to be ready for the systems coming to each site, and engaging the vendors directly in a “shared fate” approach to ensuring success. While each COE is necessarily focused on a particular deployment, applications almost invariably must be able to run effectively across the entire DOE HPC ecosystem. This tension between optimizing performance for a particular platform, while still being able to run with acceptable performance wherever the resources are available, is the crux of the challenge we call “performance portability”. This meeting was an opportunity to bring application developers, software providers, and vendors together to discuss this challenge and begin to chart a path forward.

  20. Portable Battery Charger Berbasis Sel Surya

    Directory of Open Access Journals (Sweden)

    Budhi Anto

    2014-04-01

    Full Text Available A type of solar battery charger is introduced in this paper. This equipment functions as a medium size rechargeable battery that is needed to move culinary merchants and coastal fishermen living in area which is not supplied by electrical networks. The equipment consists of solar module mounted onto portable mechanical construction, a 12-V 7.5-Ah lead acid battery and charge controller. Solar module charges the battery through charge controller and then the battery can be discharged to power on electric lamps for lightening culinary wagon or fisherman’s boat at night. Charge controller charges the battery with float charging which is implemented by maintaining 13.5 Volt between battery terminals and limiting the charging current to 1.5 Amperes. Charge controller circuit is based on adjustable linear voltage regulator LM338. The battery is of sealed lead acid type. This type of battery is maintenance free and more hygiene than other types of lead acid battery. The field experiment of charging the baterry of 50% residual capacity from 8 am to 4 pm under sunny weather shows that the solar module has charged the battery to its full capacity under battery safe charging conditions.Keywords: portable solar battery charger, float charging, LM338

  1. Portable Radiation Package (PRP) Instrument Handbook

    Energy Technology Data Exchange (ETDEWEB)

    Reynolds, R Michael [Remote Measurements and Research Company

    2017-08-03

    The Portable Radiation Package (PRP) was developed to provide basic radiation information in locations such as ships at sea where proper exposure is remote and difficult, the platform is in motion, and azimuth alignment is not fixed. Development of the PRP began at Brookhaven National Laboratory (BNL) in the mid-1990s and versions of it were deployed on ships in the U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Climate Research Facility’s Nauru-99 project. The PRP was deployed on ships in support of the National Aeronautics and Space Administration (NASA) Sensor Intercomparison for Marine Biological and Interdisciplinary Ocean Studies (SIMBIOS) program. Over the years the measurements have remained the same while the post-processing data analysis, especially for the FRSR, has evolved. This document describes the next-generation Portable Radiation Package (PRP2) that was developed for the DOE ARM Facility, under contract no. 9F-31462 from Argonne National Laboratory (ANL). The PRP2 has the same scientific principles that were well validated in prior studies, but has upgraded electronic hardware. The PRP2 approach is completely modular, both in hardware and software. Each sensor input is treated as a separate serial stream into the data collection computer. In this way the operator has complete access to each component of the system for purposes of error checking, calibration, and maintenance. The resulting system is more reliable, easier to install in complex situations, and more amenable to upgrade.

  2. Development and Applications of Portable Biosensors.

    Science.gov (United States)

    Srinivasan, Balaji; Tung, Steve

    2015-08-01

    The significance of microfluidics-based and microelectromechanical systems-based biosensors has been widely acknowledged, and many reviews have explored their potential applications in clinical diagnostics, personalized medicine, global health, drug discovery, food safety, and forensics. Because health care costs are increasing, there is an increasing need to remotely monitor the health condition of patients by point-of-care-testing. The demand for biosensors for detection of biological warfare agents has increased, and research is focused on ways of producing small portable devices that would allow fast, accurate, and on-site detection. In the past decade, the demand for rapid and accurate on-site detection of plant disease diagnosis has increased due to emerging pathogens with resistance to pesticides, increased human mobility, and regulations limiting the application of toxic chemicals to prevent spread of diseases. The portability of biosensors for on-site diagnosis is limited due to various issues, including sample preparation techniques, fluid-handling techniques, the limited lifetime of biological reagents, device packaging, integrating electronics for data collection/analysis, and the requirement of external accessories and power. Many microfluidic, electronic, and biological design strategies, such as handling liquids in biosensors without pumps/valves, the application of droplet-based microfluidics, paper-based microfluidic devices, and wireless networking capabilities for data transmission, are being explored.

  3. Portable Facial Recognition Jukebox Using Fisherfaces (Frj

    Directory of Open Access Journals (Sweden)

    Richard Mo

    2016-03-01

    Full Text Available A portable real-time facial recognition system that is able to play personalized music based on the identified person’s preferences was developed. The system is called Portable Facial Recognition Jukebox Using Fisherfaces (FRJ. Raspberry Pi was used as the hardware platform for its relatively low cost and ease of use. This system uses the OpenCV open source library to implement the computer vision Fisherfaces facial recognition algorithms, and uses the Simple DirectMedia Layer (SDL library for playing the sound files. FRJ is cross-platform and can run on both Windows and Linux operating systems. The source code was written in C++. The accuracy of the recognition program can reach up to 90% under controlled lighting and distance conditions. The user is able to train up to 6 different people (as many as will fit in the GUI. When implemented on a Raspberry Pi, the system is able to go from image capture to facial recognition in an average time of 200ms.

  4. Intelligent hand-portable proliferation sensing system

    Energy Technology Data Exchange (ETDEWEB)

    Dieckman, S.L.; Bostrom, G.A.; Waterfield, L.G.; Jendrzejczyk, J.A.; Ahuja, S.; Raptis, A.C.

    1997-08-01

    Argonne National Laboratory, with support from DOE`s Office of Nonproliferation and National Security, is currently developing an intelligent hand-portable sensor system. This system is designed specifically to support the intelligence community with the task of in-field sensing of nuclear proliferation and related activities. Based upon pulsed laser photo-ionization time-of-flight mass spectrometry technology, this novel sensing system is capable of quickly providing a molecular or atomic analysis of specimens. The system is capable of analyzing virtually any gas phase molecule, or molecule that can be induced into the gas phase by (for example) sample heating. This system has the unique advantages of providing unprecedented portability, excellent sensitivity, tremendous fieldability, and a high performance/cost ratio. The system will be capable of operating in a highly automated manner for on-site inspections, and easily modified for other applications such as perimeter monitoring aboard a plane or drone. The paper describes the sensing system.

  5. DECONTAMINATION OF LOCALITIES IN THE BRYANSK REGION AFTER THE CHERNOBYL ACCIDENT

    Directory of Open Access Journals (Sweden)

    M. I. Balonov

    2014-01-01

    Full Text Available The paper presents at first time in Russian the experience of decontamination of settlements located in the ‘Strict control area’ of the Bryansk region. Large scale decontamination campaign was implemented in summer 1989 by Russian Civil Defence forces jointly with the experts of the Institute of Radiation Hygiene. Radiological criteria  for  decontamination  are  presented  and  external  dosimetry  of  the  public  considered.  Recommendations for  decontamination  of  settlements  were  developed  based  on  modeling  and  experiments.  During  five  months, 93  settlements  with  population  of  90  this.  were  decontaminated.  Repeated  radiation  measurements  next  year and  afterwards  proved  that  there  was  no  radioactive  re-contamination  of  the  treated  areas.  Effectiveness  of decontamination was estimated by modeling and by individual TLD measurements conducted before and after decontamination. The results of two methods agreed well and the average effectiveness was estimated as 20%. The collective effective dose averted by the decontamination works in 1989 was estimated as 350 man-Sv.

  6. A decontamination system for chemical weapons agents using a liquid solution on a solid sorbent

    Energy Technology Data Exchange (ETDEWEB)

    Waysbort, Daniel [Israel Institute for Biological Research, PO Box 19, Ness-Ziona 74100 (Israel); McGarvey, David J. [R and T Directorate, Edgewood Chemical and Biological Center (ECBC), Aberdeen Proving Ground-Edgewood Area, MD 21010 (United States)], E-mail: david.mcgarvey@us.army.mil; Creasy, William R.; Morrissey, Kevin M.; Hendrickson, David M. [SAIC, P.O. Box 68, Gunpowder Branch, Aberdeen Proving Ground, MD 21010 (United States); Durst, H. Dupont [R and T Directorate, Edgewood Chemical and Biological Center (ECBC), Aberdeen Proving Ground-Edgewood Area, MD 21010 (United States)

    2009-01-30

    A decontamination system for chemical warfare agents was developed and tested that combines a liquid decontamination reagent solution with solid sorbent particles. The components have fewer safety and environmental concerns than traditional chlorine bleach-based products or highly caustic solutions. The liquid solution, based on Decon Green{sup TM}, has hydrogen peroxide and a carbonate buffer as active ingredients. The best solid sorbents were found to be a copolymer of ethylene glycol dimethacrylate and n-lauryl methacrylate (Polytrap 6603 Adsorber); or an allyl methacrylate cross-linked polymer (Poly-Pore E200 Adsorber). These solids are human and environmentally friendly and are commonly used in cosmetics. The decontaminant system was tested for reactivity with pinacolyl methylphosphonofluoridate (Soman, GD), bis(2-chloroethyl)sulfide (Mustard, HD), and S-(2-diisopropylaminoethyl) O-ethyl methylphosphonothioate (VX) by using NMR Spectroscopy. Molybdate ion (MoO{sub 4}{sup -2}) was added to the decontaminant to catalyze the oxidation of HD. The molybdate ion provided a color change from pink to white when the oxidizing capacity of the system was exhausted. The decontaminant was effective for ratios of agent to decontaminant of up to 1:50 for VX (t{sub 1/2} {<=} 4 min), 1:10 for HD (t{sub 1/2} < 2 min with molybdate), and 1:10 for GD (t{sub 1/2} < 2 min). The vapor concentrations of GD above the dry sorbent and the sorbent with decontamination solution were measured to show that the sorbent decreased the vapor concentration of GD. The E200 sorbent had the additional advantage of absorbing aqueous decontamination solution without the addition of an organic co-solvent such as isopropanol, but the rate depended strongly on mixing for HD.

  7. Evaluation of Microwave Steam Bags for the Decontamination of Filtering Facepiece Respirators

    OpenAIRE

    Fisher, Edward M.; Jessica L Williams; Shaffer, Ronald E.

    2011-01-01

    Reusing filtering facepiece respirators (FFRs) has been suggested as a strategy to conserve available supplies for home and healthcare environments during an influenza pandemic. For reuse to be possible, used FFRs must be decontaminated before redonning to reduce the risk of virus transmission; however, there are no approved methods for FFR decontamination. An effective method must reduce the microbial threat, maintain the function of the FFR, and present no residual chemical hazard. The meth...

  8. An efficient multistrategy DNA decontamination procedure of PCR reagents for hypersensitive PCR applications.

    Directory of Open Access Journals (Sweden)

    Sophie Champlot

    Full Text Available BACKGROUND: PCR amplification of minute quantities of degraded DNA for ancient DNA research, forensic analyses, wildlife studies and ultrasensitive diagnostics is often hampered by contamination problems. The extent of these problems is inversely related to DNA concentration and target fragment size and concern (i sample contamination, (ii laboratory surface contamination, (iii carry-over contamination, and (iv contamination of reagents. METHODOLOGY/PRINCIPAL FINDINGS: Here we performed a quantitative evaluation of current decontamination methods for these last three sources of contamination, and developed a new procedure to eliminate contaminating DNA contained in PCR reagents. We observed that most current decontamination methods are either not efficient enough to degrade short contaminating DNA molecules, rendered inefficient by the reagents themselves, or interfere with the PCR when used at doses high enough to eliminate these molecules. We also show that efficient reagent decontamination can be achieved by using a combination of treatments adapted to different reagent categories. Our procedure involves γ- and UV-irradiation and treatment with a mutant recombinant heat-labile double-strand specific DNase from the Antarctic shrimp Pandalus borealis. Optimal performance of these treatments is achieved in narrow experimental conditions that have been precisely analyzed and defined herein. CONCLUSIONS/SIGNIFICANCE: There is not a single decontamination method valid for all possible contamination sources occurring in PCR reagents and in the molecular biology laboratory and most common decontamination methods are not efficient enough to decontaminate short DNA fragments of low concentration. We developed a versatile multistrategy decontamination procedure for PCR reagents. We demonstrate that this procedure allows efficient reagent decontamination while preserving the efficiency of PCR amplification of minute quantities of DNA.

  9. Timing of decontamination and treatment in case of percutaneous VX poisoning: a mini review.

    Science.gov (United States)

    Joosen, Marloes J A; van der Schans, Marcel J; Kuijpers, Willem C; van Helden, Herman P M; Noort, Daan

    2013-03-25

    Low volatile organophosphorous nerve agents such as VX, will most likely enter the body via the skin. The pharmacokinetics of drugs such as oximes, atropine and diazepam, are not aligned with the variable and persistent toxicokinetics of the agent. Repeated administration of these drugs showed to improve treatment efficacy compared to a single injection treatment. Because of the effectiveness of continuous treatment, it was investigated to what extent a subchronic pretreatment with carbamate (pyridostigmine or physostigmine combined with either procyclidine or scopolamine) would protect against percutaneous VX exposure. Inclusion of scopolamine in the pretreatment prevented seizures in all animals, but none of the pretreatments affected survival time or the onset time of cholinergic signs. These results indicate that percutaneous poisoning with VX requires additional conventional treatment in addition to the current pretreatment regimen. Decontamination of VX-exposed skin is one of the most important countermeasures to mitigate the effects of the exposure. To evaluate the window of opportunity for decontamination, the fielded skin decontaminant Reactive Skin Decontaminant Lotion (RSDL) was tested at different times in hairless guinea pigs percutaneously challenged with 4× LD50 VX in IPA. The results showed that RSDL decontamination at 15 min after exposure could not prevent progressive blood cholinesterase inhibition and therefore would still require additional treatment. A similar decontamination regimen with RSDL at 90 min showed that it still might effectively increase the time window of opportunity for treatment. In conclusion, the delay in absorption presents a window of opportunity for decontamination and treatment. The continuous release of VX from the skin presents a significant challenge for efficacious therapy, which should ideally consist of thorough decontamination and continuous treatment.

  10. Mesoporous binary metal oxide nanocomposites: Synthesis, characterization and decontamination of sulfur mustard

    Energy Technology Data Exchange (ETDEWEB)

    Praveen Kumar, J., E-mail: praveenjella10@gmail.com; Prasad, G.K.; Ramacharyulu, P.V.R.K.; Singh, Beer; Gopi, T.; Krishna, R.

    2016-04-15

    Mesoporous MnO{sub 2}–ZnO, Fe{sub 2}O{sub 3}–ZnO, NiO–ZnO, and CeO{sub 2}–ZnO binary metal oxide nanocomposites were studied as sorbent decontaminants against sulfur mustard. They were synthesized by precipitation pyrolysis method and characterized by means of transmission electron microscopy, scanning electron microscopy coupled with energy dispersive analysis of X rays, X ray diffraction, and nitrogen adsorption techniques. The transmission electron microscopy and nitrogen adsorption data indicated the presence of pores with diameter ranging from 10 to 70 nm in the binary metal oxide nanocomposites and these materials exhibited surface area values in the range of 76–134 m{sup 2}/g. These binary metal oxide nanocomposites demonstrated large decontamination efficiencies against sulfur mustard when compared to their single component metal oxide nanoparticles. The binary metal oxide nanocomposites effectively decontaminated sulfur mustard into relatively non toxic products such as chloro ethyl vinyl sulfide, divinyl sulfide, 1,4-oxathiane, etc. The promising decontamination properties of binary metal oxide nanocomposites against sulfur mustard were attributed to the basic sites, Lewis acid sites, and the presence of these sites was confirmed by CO{sub 2} and NH{sub 3} temperature programmed desorption. - Graphical abstract: Mesoporous MnO{sub 2}–ZnO, Fe{sub 2}O{sub 3}–ZnO, NiO–ZnO, and CeO{sub 2}–ZnO binary metal oxide nanocomposites were studied as sorbent decontaminants against sulfur mustard. - Highlights: • Binary metal oxide nanocomposites were synthesized by co-precipitation method. • They were studied as sorbent decontaminants against sulfur mustard. • They decontaminated sulfur mustard into non toxic products. • MnO{sub 2}–ZnO and CeO{sub 2}–ZnO nanocomposites showed greater decontamination efficiency.

  11. Decontamination System Development of Radioative Activated Carbon using Micro-bubbles

    Energy Technology Data Exchange (ETDEWEB)

    Jeon, Jong seon; Kim, Wi soo [NESS, Daejeon (Korea, Republic of); Han, Byoung sub. [Enesys Co., Daejeon (Korea, Republic of)

    2016-10-15

    This study was aimed to develop a decontamination system by applying such technical characteristics that minimizes a generation of secondary wastes while decontaminating radiation wastes. The radioactive activated carbon is removed from the end-of-life air cleaning filter in replacement or decommission of nuclear power plant or nuclear facility. By removing radioactive activated carbon, the filter would be classified as a low radioactive contaminant. And thus the amount of radioactive wastes and the treatment cost would be decreased. We are in development of the activated carbon cleaning technique by utilizing micro-bubbles, which improve efficiency and minimize damage of activated carbon. The purpose of using micro-bubbles is to decontamination carbon micropore, which is difficult to access, by principle of cavitation phenomenon generated in collapse of micro-bubbles. In this study, we introduced the micro-bubble decontamination system developed to decontaminate activated carbon. For further researches, we will determine carbon weight change and the decontamination rate under the experimental conditions such as temperature and pH.

  12. Conversion of transuranic waste to low level waste by decontamination: a technical and economic evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Allen, R.P.; Hazelton, R.F.

    1984-12-01

    A study was conducted to evaluate the technical and economic feasibility of using in-situ decontamination techniques to convert glove boxes and other large TRU-contaminated components directly into LLW. The results of the technical evaluation indicate that in-situ decontamination of these types of components to non-TRU levels is technically feasible. Applicable decontamination techniques include electropolishing, hand scrubbing, chemical washes/sprays, strippable coatings and Freon spray-cleaning. The removal of contamination from crevices and other holdup areas remains a problem, but may be solved through further advances in decontamination technology. Also, the increase in the allowable maximum TRU level from 10 nCi/g to 100 nCi/g as defined in DOE Order 5820.2 reduces the removal requirement and facilitates measurement of the remaining quantities. The major emphasis of the study was on a cost/benefit evaluation that included a review and update of previous analyses and evaluations of TRU-waste volume reduction and conversion options. The results of the economic evaluation show, for the assumptions used, that there is a definite cost incentive to size reduce large components, and that decontamination of sectioned material has become cost competitive with the size reduction options. In-situ decontamination appears to be the lowest cost option when based on routine-type operations conducted by well-trained and properly equipped personnel. 16 references, 1 figure, 7 tables.

  13. Decontamination of biological agents from drinking water infrastructure: a literature review and summary.

    Science.gov (United States)

    Szabo, Jeff; Minamyer, Scott

    2014-11-01

    This report summarizes the current state of knowledge on the persistence of biological agents on drinking water infrastructure (such as pipes) along with information on decontamination should persistence occur. Decontamination options for drinking water infrastructure have been explored for some biological agents, but data gaps remain. Data on bacterial spore persistence on common water infrastructure materials such as iron and cement-mortar lined iron show that spores can be persistent for weeks after contamination. Decontamination data show that common disinfectants such as free chlorine have limited effectiveness. Decontamination results with germinant and alternate disinfectants such as chlorine dioxide are more promising. Persistence and decontamination data were collected on vegetative bacteria, such as coliforms, Legionella and Salmonella. Vegetative bacteria are less persistent than spores and more susceptible to disinfection, but the surfaces and water quality conditions in many studies were only marginally related to drinking water systems. However, results of real-world case studies on accidental contamination of water systems with E. coli and Salmonella contamination show that flushing and chlorination can help return a water system to service. Some viral persistence data were found, but decontamination data were lacking. Future research suggestions focus on expanding the available biological persistence data to other common infrastructure materials. Further exploration of non-traditional drinking water disinfectants is recommended for future studies.

  14. Decontamination of FAST (CPP-666) fuel storage area stainless steel fuel storage racks

    Energy Technology Data Exchange (ETDEWEB)

    Kessinger, G.F.

    1993-10-01

    The purpose of this report was to identify and evaluate alternatives for the decontamination of the RSM stainless steel that will be removed from the Idaho Chemical Processing plant (ICPP) fuel storage area (FSA) located in the FAST (CPP-666) building, and to recommend decontamination alternatives for treating this material. Upon the completion of a literature search, the review of the pertinent literature, and based on the review of a variety of chemical, mechanical, and compound (both chemical and mechanical) decontamination techniques, the preliminary results of analyses of FSA critically barrier contaminants, and the data collected during the FSA Reracking project, it was concluded that decontamination and beneficial recycle of the FSA stainless steel produced is technically feasible and likely to be cost effective as compared to burying the material at the RWMC. It is recommended that an organic acid, or commercial product containing an organic acid, be used to decontaminate the FSA stainless steel; however, it is also recommended that other surface decontamination methods be tested in the event that this method proves unsuitable. Among the techniques that should be investigated are mechanical techniques (CO{sub 2} pellet blasting and ultra-high pressure water blasting) and chemical techniques that are compatible with present ICPP waste streams.

  15. Effect of surface modification of silica nanoparticles on foam stability in decontamination foam

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, In-Ho; Jung, Chong-Hun; Kim, Chorong; Yang, Han-Beom; Choi, Mansoo; Moon, Jei-Kwon; Choi, Wang-Kyu [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    Decontamination foam is a non-stable, two-phase fluid with aqueous and gas phases representing not more than 10% and 90% of the total volume, respectively. This formulation can significantly decrease the amounts of chemical reagents and secondary waste. The advantage of decontamination foam is its potentially wide application for metallic walls, overhead surfaces, and the elements of complex components and facilities. In addition, the application of foam allows for remote decontamination processing using only an injection nozzle and the equipment to generate the decontamination foam, which reduces operator exposure to high radioactivity. Solid colloidal particles increase the foam stability in the foam formulation. These particles can be specifically hydrophobized for optimal adsorption at the liquid/gas interface, which creates armor for the bubbles and prevents coalescence by reducing the internal gas transfer. Conversely, hydrophilic particles remain confined in the liquid phase, and to enhance the foam stability. In this study, we aimed to modify the surface of silica nanoparticles with dichlorodimethylsilane (DCDMS) reagents using methods proposed in previous literatures. We plan to investigate further the influence pH and the concentration of chemical reagent in decontamination foam system. In future studies, decontamination tests will be conducted on a surface contaminated with radionuclides such as cesium and cobalt.

  16. Hairy skin exposure to VX in vitro: effectiveness of delayed decontamination.

    Science.gov (United States)

    Rolland, P; Bolzinger, M-A; Cruz, C; Josse, D; Briançon, S

    2013-02-01

    The chemical warfare agents such as VX represent a threat for both military and civilians, which involves an immediate need of effective decontamination systems. Since human scalp is usually unprotected compared to other body regions covered with clothes, it could be a preferential site of exposure in case of terrorist acts. The purpose of this study was to determine if skin decontamination could be efficient when performed more than 1h after exposure. In addition, the impact of hairs in skin contamination was investigated. By using in vitro skin models, we demonstrated that about 75% of the applied quantity of VX was recovered on the skin surface 2h after skin exposition, which means that it is worth decontaminating even if contamination occurred 2h before. The stratum corneum reservoir for VX was quickly established and persistent. In addition, the presence of hairs modified the percutaneous penetration of the nerve agent by binding of VX to hairs. Hair shaft has thus to be taken into account in the decontamination process. Reactive Skin Decontamination Lotion (RSDL) and Fuller's Earth (FE) were active in the skin decontamination 45min post-exposure, but RSDL was more efficient in reducing the amount of VX either in the skin or in the hair.

  17. Off-site consequences of radiological accidents: methods, costs and schedules for decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Tawil, J.J.; Bold, F.C.; Harrer, B.J.; Currie, J.W.

    1985-08-01

    This report documents a data base and a computer program for conducting a decontamination analysis of a large, radiologically contaminated area. The data base, which was compiled largely through interviews with knowledgeable persons both in the public and private sectors, consists of the costs, physical inputs, rates and contaminant removal efficiencies of a large number of decontamination procedures. The computer program utilizes this data base along with information specific to the contaminated site to provide detailed information that includes the least costly method for effectively decontaminating each surface at the site, various types of property losses associated with the contamination, the time at which each subarea within the site should be decontaminated to minimize these property losses, the quantity of various types of labor and equipment necessary to complete the decontamination, dose to radiation workers, the costs for surveying and monitoring activities, and the disposal costs associated with radiological waste generated during cleanup. The program and data base are demonstrated with a decontamination analysis of a hypothetical site. 39 refs., 24 figs., 155 tabs.

  18. 49 CFR 174.63 - Portable tanks, IM portable tanks, IBCs, Large Packagings, cargo tanks, and multi-unit tank car...

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Portable tanks, IM portable tanks, IBCs, Large Packagings, cargo tanks, and multi-unit tank car tanks. 174.63 Section 174.63 Transportation Other....63 Portable tanks, IM portable tanks, IBCs, Large Packagings, cargo tanks, and multi-unit tank...

  19. 48 CFR 1852.237-71 - Pension portability.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Pension portability. 1852.237-71 Section 1852.237-71 Federal Acquisition Regulations System NATIONAL AERONAUTICS AND SPACE... 1852.237-71 Pension portability. As prescribed at 1837.110-70(b), insert the following clause:...

  20. 49 CFR 178.274 - Specifications for UN portable tanks.

    Science.gov (United States)

    2010-10-01

    ... from a fire (see § 178.275(g)). Jacket means the outer insulation cover or cladding which may be part... attachments and supports between the shell and jacket, provided their material properties at the minimum and... loads through the expected life of the portable tank. (2) Portable tank shells, fittings, and pipework...

  1. 36 CFR 1194.26 - Desktop and portable computers.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Desktop and portable computers. 1194.26 Section 1194.26 Parks, Forests, and Public Property ARCHITECTURAL AND TRANSPORTATION... § 1194.26 Desktop and portable computers. (a) All mechanically operated controls and keys shall comply...

  2. 33 CFR 127.203 - Portable gas detectors.

    Science.gov (United States)

    2010-07-01

    ...) WATERFRONT FACILITIES WATERFRONT FACILITIES HANDLING LIQUEFIED NATURAL GAS AND LIQUEFIED HAZARDOUS GAS Waterfront Facilities Handling Liquefied Natural Gas Equipment § 127.203 Portable gas detectors. The marine... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Portable gas detectors....

  3. 14 CFR 91.21 - Portable electronic devices.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Portable electronic devices. 91.21 Section... electronic devices. (a) Except as provided in paragraph (b) of this section, no person may operate, nor may any operator or pilot in command of an aircraft allow the operation of, any portable electronic...

  4. The portability of the "Electronics Workbench" simulation software to China

    NARCIS (Netherlands)

    Collis, Betty; Zhi-Cheng, Dong

    1993-01-01

    This article discusses the portability of the Canadian-made simulation software package, "Electronic Workbench" package (EWB) to China. As part of a larger project investigating the portability of various educational software packages, the EWB package was used in electronics instruction in China and

  5. Adaptable educational courseware : an antidote to several portability problems

    NARCIS (Netherlands)

    De Diana, I.P.F.; Vries, de S.A.

    1990-01-01

    The concepts of adaptability and portability of educational software and courseware seem to be interwoven in several respects. This article explores these interrelationships in some detail, based upon the presumption that adaptable educational products are also more portable. A conceptual framework

  6. 14 CFR 121.306 - Portable electronic devices.

    Science.gov (United States)

    2010-01-01

    ... section does not apply to— (1) Portable voice recorders; (2) Hearing aids; (3) Heart pacemakers; (4) Electric shavers; or (5) Any other portable electronic device that the part 119 certificate holder has determined will not cause interference with the navigation or communication system of the aircraft on...

  7. 30 CFR 75.1703 - Portable electric lamps.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Portable electric lamps. 75.1703 Section 75... HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Miscellaneous § 75.1703 Portable electric lamps. Persons underground shall use only permissible electric lamps approved by the Secretary for...

  8. Stress analysis of portable safety platform (Core Sampler Truck)

    Energy Technology Data Exchange (ETDEWEB)

    Ziada, H.H.

    1995-03-30

    This document provides the stress analysis and evaluation of the portable platform of the rotary mode core sampler truck No. 2 (RMCST {number_sign}2). The platform comprises railing, posts, deck, legs, and a portable ladder; it is restrained from lateral motion by means of two brackets added to the drill-head service platform.

  9. 29 CFR 1910.25 - Portable wood ladders.

    Science.gov (United States)

    2010-07-01

    ... user equips them with safety shoes; (xviii) (xix) The user should equip all portable rung ladders with... Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR OCCUPATIONAL SAFETY AND HEALTH STANDARDS Walking-Working Surfaces § 1910.25 Portable wood ladders....

  10. 77 FR 58576 - Certain Wireless Communication Devices, Portable Music and Data Processing Devices, Computers...

    Science.gov (United States)

    2012-09-21

    ... COMMISSION Certain Wireless Communication Devices, Portable Music and Data Processing Devices, Computers, and... importation of certain wireless communication devices, portable music and data processing devices, computers... after importation of certain wireless communication devices, portable music and data processing...

  11. 77 FR 51571 - Certain Wireless Communication Devices, Portable Music and Data Processing Devices, Computers...

    Science.gov (United States)

    2012-08-24

    ... COMMISSION Certain Wireless Communication Devices, Portable Music and Data Processing Devices, Computers, and... communication devices, portable music and data processing devices, computers, and components thereof. The.... International Trade Commission has received a complaint entitled Wireless Communication Devices, Portable...

  12. 78 FR 12785 - Certain Wireless Communication Devices, Portable Music and Data Processing Devices, Computers and...

    Science.gov (United States)

    2013-02-25

    ... COMMISSION Certain Wireless Communication Devices, Portable Music and Data Processing Devices, Computers and... communication devices, portable music and data processing devices, computers and components thereof by reason of... evidence demonstrates that the existence of portable communication devices using ``touch sensitive...

  13. Bioremediation of {sup 60}Co from simulated spent decontamination solutions

    Energy Technology Data Exchange (ETDEWEB)

    Rashmi, K.; Naga Sowjanya, T.; Maruthi Mohan, P.; Balaji, V.; Venkateswaran, G

    2004-07-26

    Bioremediation of {sup 60}Co from simulated spent decontamination solutions by utilizing different biomass of (Neurospora crassa, Trichoderma viridae, Mucor recemosus, Rhizopus chinensis, Penicillium citrinum, Aspergillus niger and, Aspergillus flavus) fungi is reported. Various fungal species were screened to evaluate their potential for removing cobalt from very low concentrations (0.03-0.16 {mu}M) in presence of a high background of iron (9.33 mM) and nickel (0.93 mM) complexed with EDTA (10.3 mM). The different fungal isolates employed in this study showed a pickup of cobalt in the range 8-500 ng/g of dry biomass. The [Fe]/[Co] and [Ni]/[Co] ratios in the solutions before and after exposure to the fungi were also determined. At micromolar level the cobalt pickup by many fungi especially the mutants of N. crassa is seen to be proportional to the initial cobalt concentration taken in the solution. However, R. chinensis exhibits a low but iron concentration dependent cobalt pickup. Prior saturating the fungi with excess of iron during their growth showed the presence of selective cobalt pickup sites. The existence of cobalt specific sorption sites is shown by a model experiment with R. chinensis wherein at a constant cobalt concentration (0.034 {mu}M) and varying iron concentrations so as to yield [Fe/Co]{sub initial} ratios in solution of 10, 100, 1000 and 287 000 have all yielded a definite Co pickup capacity in the range 8-47 ng/g. The presence of Cr(III)EDTA (3 mM) in solution along with complexed Fe and Ni has not influenced the cobalt removal. The significant feature of this study is that even when cobalt is present in trace level (sub-micromolar) in a matrix of high concentration (millimolar levels) of iron, nickel and chromium, a situation typically encountered in spent decontamination solutions arising from stainless steel based primary systems of nuclear reactors, a number of fungi studied in this work showed a good sensitivity for cobalt pickup.

  14. Self-Decontaminating Fibrous Materials Reactive toward Chemical Threats.

    Science.gov (United States)

    Bromberg, Lev; Su, Xiao; Martis, Vladimir; Zhang, Yunfei; Hatton, T Alan

    2016-07-13

    Polymers that possess highly nucleophilic pyrrolidinopyridine (Pyr) and primary amino (vinylamine, VAm) groups were prepared by free-radical copolymerization of N,N-diallylpyridin-4-amine (DAAP) and N-vinylformamide (NVF) followed by acidic hydrolysis of NVF into VAm. The resulting poly(DAAP-co-VAm-co-NVF) copolymers were water-soluble and reacted with water-dispersible polyurethane possessing a high content of unreacted isocyanate groups. Spray-coating of the nylon-cotton (NYCO), rayon, and poly(p-phenylene terephthalamide) (Kevlar 119) fibers pretreated with phosphoric acid resulted in covalent bonding of the polyurethane with the hydroxyl groups on the fiber surface. A second spray-coating of aqueous solutions of poly(DAAP-co-VAm-co-NVF) on the polyurethane-coated fiber enabled formation of urea linkages between unreacted isocyanate groups of the polyurethane layer and the amino groups of poly(DAAP-co-VAm-co-NVF). Fibers with poly(DAAP-co-VAm-co-NVF) attached were compared with fibers modified by adsorption of water-insoluble poly(butadiene-co-pyrrolidinopyridine) (polyBPP) in terms of the stability against polymer leaching in aqueous washing applications. While the fibers modified by attachment of poly(DAAP-co-VAm-co-NVF) exhibited negligible polymer leaching, over 65% of adsorbed polyBPP detached and leached from the fibers within 7 days. Rayon fibers modified by poly(DAAP-co-VAm-co-NVF) were tested for sorption of dimethyl methylphosphonate (DMMP) in the presence of moisture using dynamic vapor sorption technique. Capability of the fibers modified with poly(DAAP-co-VAm-co-NVF) to facilitate hydrolysis of the sorbed DMMP in the presence of moisture was uncovered. The self-decontaminating property of the modified fibers against chemical threats was tested using a CWA simulant diisopropylfluorophosphate (DFP) in aqueous media at pH 8.7. Fibers modified with poly(DAAP-co-VAm-co-NVF) facilitated hydrolysis of DFP with the half-lives up to an order of magnitude

  15. Decontamination of hard cheeses by pulsed UV light.

    Science.gov (United States)

    Can, Fidan O; Demirci, Ali; Puri, Virendra M; Gourama, Hassan

    2014-10-01

    Cheese is a ready-to-eat food that may be contaminated on the surface by undesirable spoilage and pathogenic microorganisms during production, packaging, and postpackaging processes. Penicillium roqueforti is commonly found on cheese surfaces at refrigeration temperatures and is one of the most common spoilage fungal species. Consumption of cheese contaminated with Listeria monocytogenes can result in foodborne listeriosis. Therefore, cheese should be decontaminated at postprocessing stages. Pulsed UV light is a nonthermal method for food preservation that involves the use of intense short pulses to ensure microbial decontamination on the surface of foods or packaging materials. In this study, the efficacy of pulsed UV light for inactivation of P. roqueforti and L. monocytogenes inoculated onto packaged and unpackaged hard cheeses was investigated. Treatment times and the distance from the UV strobe were evaluated to determine optimum treatment conditions. Packaged and unpackaged cheeses were treated at distances of 5, 8, and 13 cm for up to 60 s. For P. roqueforti, maximum reduction after 40 s at 5 cm was 1.32 log CFU/cm(2) on unpackaged cheese and 1.24 log CFU/cm(2) on packaged cheese. Reductions of L. monocytogenes under the same treatment conditions were about 2.9 and 2.8 log CFU/cm(2) on packaged and unpackaged cheeses, respectively. The temperature changes and total energy increases were directly proportional to treatment time and inversely proportional to distance between the UV lamp and the samples. The changes in color and lipid oxidation were determined at mild (5 s at 13 cm), moderate (30 s at 8 cm), and extreme (40 s at 5 cm) treatments. The color and chemical quality of cheeses were not significantly different after mild treatments (P > 0.05). The mechanical properties of the plastic packaging material (polypropylene) also were evaluated after mild, moderate, and extreme treatments. A decreasing trend was noted for elastic modulus; however, no

  16. Portable fiber sensors based on surface-enhanced Raman scattering.

    Science.gov (United States)

    Yang, Xuan; Tanaka, Zuki; Newhouse, Rebecca; Xu, Qiao; Chen, Bin; Chen, Shaowei; Zhang, Jin Z; Gu, Claire

    2010-12-01

    Two portable molecular sensing systems based on surface-enhanced Raman scattering (SERS) have been experimentally demonstrated using either a tip-coated multimode fiber (TCMMF) or a liquid core photonic crystal fiber (LCPCF) as the SERS probe. With Rhodamine 6G as a test molecule, the TCMMF-portable SERS system achieved 2-3 times better sensitivity than direct sampling (focusing the laser light directly into the sample without the fiber probe), and a highly sensitive LCPCF-portable SERS system reached a sensitivity up to 59 times that of direct sampling, comparable to the sensitivity enhancement achieved using fiber probes in the bulky Renishaw system. These fiber SERS probes integrated with a portable Raman spectrometer provide a promising scheme for a compact and flexible molecular sensing system with high sensitivity and portability.

  17. Universal Oxidation for CBW Decontamination: L-Gel System Development and Deployment

    Energy Technology Data Exchange (ETDEWEB)

    Raber, E.; McGuire, R.; Hoffman, M.; Alcaraz, A.; Shepley, D.; Elliot, J.; Krauter, P.; Garcia, E.

    2000-12-16

    The general philosophy of this work is to develop an integrated set of decontamination methods and tools that will work on the major CBW threat agents. The work includes some near term techniques that can be demonstrated within a year and implemented soon thereafter as well as longer term research objectives. It is recognized that there is a balance between somewhat less effective methods which can be demonstrated quickly and more effective ones which may require a much longer time to fruition. The optimum goal of this study is to find a single decontamination system for chemical and biological agents which is non-toxic, non-corrosive, and easily deployable. One of the goals is to have decontamination systems that might be used by first responders as well as more complete systems to be used by specialized decontamination teams. Therefore, the overall project goal is to develop better decontamination methods that can be quickly implemented by these organizations. This includes early demonstrations and field work with companies or other government agencies who can identify implementation concerns and needs. The approach taken in this work is somewhat different than the standard military approach to decontamination. In a battlefield scenario, it is critical to decontaminate to a useful level in a very short time so the soldiers can continue their mission. In a domestic, urban scenario, time is of less consequence but collateral damage and recertification (public perception and stakeholder acceptance) are of much greater importance. The specific objective of the LLNL work to date has been to evaluate various oxidizer systems as reagents to allow for detoxification and/or degradation to non-toxic environmentally acceptable components rather than necessitate complete destruction. Detoxification requires less reagent material than total oxidation, thereby reducing the logistic burden for a decontamination team. Since we also wanted to maximize the contact time between the

  18. Large-Scale Urban Decontamination; Developments, Historical Examples and Lessons Learned

    Energy Technology Data Exchange (ETDEWEB)

    Rick Demmer

    2007-02-01

    Recent terrorist threats and actual events have lead to a renewed interest in the technical field of large scale, urban environment decontamination. One of the driving forces for this interest is the real potential for the cleanup and removal of radioactive dispersal device (RDD or “dirty bomb”) residues. In response the U. S. Government has spent many millions of dollars investigating RDD contamination and novel decontamination methodologies. Interest in chemical and biological (CB) cleanup has also peaked with the threat of terrorist action like the anthrax attack at the Hart Senate Office Building and with catastrophic natural events such as Hurricane Katrina. The efficiency of cleanup response will be improved with these new developments and a better understanding of the “old reliable” methodologies. Perhaps the most interesting area of investigation for large area decontamination is that of the RDD. While primarily an economic and psychological weapon, the need to cleanup and return valuable or culturally significant resources to the public is nonetheless valid. Several private companies, universities and National Laboratories are currently developing novel RDD cleanup technologies. Because of its longstanding association with radioactive facilities, the U. S. Department of Energy National Laboratories are at the forefront in developing and testing new RDD decontamination methods. However, such cleanup technologies are likely to be fairly task specific; while many different contamination mechanisms, substrate and environmental conditions will make actual application more complicated. Some major efforts have also been made to model potential contamination, to evaluate both old and new decontamination techniques and to assess their readiness for use. Non-radioactive, CB threats each have unique decontamination challenges and recent events have provided some examples. The U. S. Environmental Protection Agency (EPA), as lead agency for these emergency

  19. The first chemical decontamination system for decommissioning in italy 'Phadec Technology' in Caorso

    Energy Technology Data Exchange (ETDEWEB)

    Benvenuto, F.; Lupu, M.; Mazzoni, C.; Orlandi, S.; Ricci, C. [Nuclear System Engineering Department, Ansaldo Nucleare S.p.A., Corso Perrone 25, 16161 Genova (Italy)

    2010-07-01

    The PHADEC Process (Phosphoric Acid Decontamination Process) is designed for surface decontamination of steel scrap using phosphoric acid. It has been successfully installed at Caorso NPP (Piacenza, Italy) at the end of 2008. The decontamination of steel scrap is done by removing the radioactivity localized in a few micron thickness from the surface with an electro-polishing (Stainless Steel) or acid pickling (Carbon Steel) treatment in basins filled with 40%-Phosphoric Acid that is regenerated and recycled for reuse. (authors)

  20. Portable cosmic muon telescope for environmental applications

    Energy Technology Data Exchange (ETDEWEB)

    Barnafoeldi, Gergely Gabor [Institute for Particle and Nuclear Physics, Wigner Research Centre for Physics, Hungarian Academy of Sciences, 29-33 Konkoly-Thege Miklos Str., H-1121 Budapest (Hungary); Hamar, Gergo [Institute for Particle and Nuclear Physics, Wigner Research Centre for Physics, Hungarian Academy of Sciences, 29-33 Konkoly-Thege Miklos Str., H-1121 Budapest (Hungary); Department of Physics of Complex Systems, Eoetvoes University, 1/A Pazmany P. setany, H-1117 Budapest (Hungary); Melegh, Hunor Gergely [Budapest University of Technology and Economics, 3-9 Muegyetem rkp., H-1111 Budapest (Hungary); Olah, Laszlo [Department of Physics of Complex Systems, Eoetvoes University, 1/A Pazmany P. setany, H-1117 Budapest (Hungary); Suranyi, Gergely [Geological, Geophysical and Space Science Research Group of the HAS, Eoetvoes University, 1/C Pazmany P. setany, H-1117 Budapest (Hungary); Varga, Dezso, E-mail: dezso.varga@cern.ch [Department of Physics of Complex Systems, Eoetvoes University, 1/A Pazmany P. setany, H-1117 Budapest (Hungary)

    2012-10-11

    A portable, low power consumption cosmic muon tracking system based on Close Cathode MWPC technology is presented, which is designed for operation in highly humid environmental conditions such as underground caves, tunnels, or cellars. The system measures the angular distribution of cosmic muons with resolution of 10 mrad, allowing for a tomographic mapping of the soil density above the detector unit. The size of the detector, 0.1 m{sup 2} of total sensitive surface, was designed to fulfill the requirement of transport through humanly passable natural cave tunnels. First results from the Ariadne Cave System in Pilis Mountains, Hungary are shown, which constrains the necessary data taking time for meaningful tomographic mapping. -- Highlights: Black-Right-Pointing-Pointer Cosmic muon tracking system for underground applications presented. Black-Right-Pointing-Pointer Operation in highly humid environment of natural caves demonstrated. Black-Right-Pointing-Pointer Tomographic mapping at 60 m depth was performed during 50 days in Pilis Mountains, Hungary.

  1. A portable rehabilitation device for the Hand.

    Science.gov (United States)

    Iqbal, Jamshed; Tsagarakis, Nikos G; Fiorilla, Angelo E; Caldwell, Darwin G

    2010-01-01

    This paper presents the design of a direct driven under-actuated portable hand exoskeleton for rehabilitation. The design of the proposed Hand EXOskeleton SYStem (HEXOSYS) was driven by multi-objective optimisation strategy and inspiration from the human hand. The optimisation algorithm resulted in the choice of optimum link lengths of the device. The optimisation criteria are based on dexterity, isotropy and exertion of perpendicular forces on the finger digits. Furthermore, a series of experiments on the human hand using appropriate sensory instrumentation guided the selection of actuators thereby resulting in a rehabilitation device which is compatible with the human hand force capabilities. The provision of force as well as position feedback gives quantitative feedback to the therapist and would imply a more efficient rehabilitation process. The first prototype of the device has been designed and realized.

  2. Portable design rules for bulk CMOS

    Science.gov (United States)

    Griswold, T. W.

    1982-01-01

    It is pointed out that for the past several years, one school of IC designers has used a simplified set of nMOS geometric design rules (GDR) which is 'portable', in that it can be used by many different nMOS manufacturers. The present investigation is concerned with a preliminary set of design rules for bulk CMOS which has been verified for simple test structures. The GDR are defined in terms of Caltech Intermediate Form (CIF), which is a geometry-description language that defines simple geometrical objects in layers. The layers are abstractions of physical mask layers. The design rules do not presume the existence of any particular design methodology. Attention is given to p-well and n-well CMOS processes, bulk CMOS and CMOS-SOS, CMOS geometric rules, and a description of the advantages of CMOS technology.

  3. Portable UDP port forwarding in user space

    Directory of Open Access Journals (Sweden)

    Vancea Florin

    2009-05-01

    Full Text Available Port forwarding is frequently used to selectively expose services available on remote machines to clients running on the local machine or on machines connected to the local network. Services running over TCP are easy to forward using SSH, at least as long as the details of the transported protocol are transparent. Tools are available for other classes of tunneling, including UDP tunneling. However, thesetools are not very portable and may be limited to root/admin usage or may simply not be available. We are presenting a Java client/server pair that may be successfully used in almost any environment to forward a UDP dialog over an existing forwarded TCPconnection. The tool is tested for traffic like SNMP with multiple clients and multiple targets.

  4. Portable fluorescence meter for medical applications

    Science.gov (United States)

    Kornilin, Dmitriy V.; Grishanov, Vladimir N.

    2016-04-01

    Recently, there are great deals of skin fluorescence studies for diagnostic purposes in medicine. Measurement of the intensity of autofluorescence (AF) is suitable method for diagnostic, because it does not require traumatic procedures. Skin AF is widely used by doctors in order to assess the concentration of advanced glycation endproduct (AGE). There are no in vivo fluorescence meters made in Russia, which are affordable, portable, easy-to-use and easily replicable. This paper is devoted to study of the fluorimeter and its mathematical model of spectral characteristics that were developed by authors. Fluorimeter and its software are fully operational and they were given to doctors for testing in the real clinic conditions in order to get a set of AF statistics for patients.

  5. Passive and Portable Polymer Optical Fiber Cleaver

    DEFF Research Database (Denmark)

    Saez-Rodriguez, D.; Min, R.; Ortega, B.

    2016-01-01

    Polymer optical fiber (POF) is a growing technology in short distance telecommunication due to its flexibility, easy connectorization, and lower cost than the mostly deployed silica optical fiber technology. Microstructured POFs (mPOFs) have particular promising potential applications in the sens......Polymer optical fiber (POF) is a growing technology in short distance telecommunication due to its flexibility, easy connectorization, and lower cost than the mostly deployed silica optical fiber technology. Microstructured POFs (mPOFs) have particular promising potential applications...... opening up the possibility of an electrically passive cleaver. In this letter, we describe the implementation and testing of a high quality cleaver based on a mechanical system formed by a constant force spring and a damper, which leads to the first reported electrical passive and portable cleaver....

  6. Portable mini gamma camera for medical applications

    CERN Document Server

    Porras, E; Benlloch, J M; El-Djalil-Kadi-Hanifi, M; López, S; Pavon, N; Ruiz, J A; Sánchez, F; Sebastiá, A

    2002-01-01

    A small, portable and low-cost gamma camera for medical applications has been developed and clinically tested. This camera, based on a scintillator crystal and a Position Sensitive Photo-Multiplier Tube, has a useful field of view of 4.6 cm diameter and provides 2.2 mm of intrinsic spatial resolution. Its mobility and light weight allow to reach the patient from any desired direction. This camera images small organs with high efficiency and so addresses the demand for devices of specific clinical applications. In this paper, we present the camera and briefly describe the procedures that have led us to choose its configuration and the image reconstruction method. The clinical tests and diagnostic capability are also presented and discussed.

  7. Note: A portable rotating waveplate polarimeter

    Science.gov (United States)

    Bobach, Søren; Hidic, Adnan; Arlt, Jan J.; Hilliard, Andrew J.

    2017-03-01

    We describe the construction and performance of a polarimeter based on a quarter-wave plate rotated by a model airplane motor. The motor rotates at a high angular frequency of ω ˜2 π ×160 Hz, which enables the polarimeter to monitor the polarization state of an incident beam of light in real-time. We show that a simple analysis of the polarimeter signal using the fast Fourier transform on a standard digital oscilloscope provides an excellent measure of the polarization state for many laboratory applications. The polarimeter is straightforward to construct, portable, and features a high-dynamic range, facilitating a wide range of optics laboratory tasks that require free-space or fiber-based polarization analysis.

  8. Portable calibration instrument of hemodialysis unit

    Science.gov (United States)

    Jin, Liang-bing; Li, Dong-sheng; Chen, Ai-jun

    2013-01-01

    For the purpose of meeting the rapid development of blood purification in China, improve the level of blood purification treatment, and get rid of the plight of the foreign technology monopolization to promise patients' medical safety, a parameter-calibrator for the hemodialysis unit, which can detect simultaneously multi-parameter, is designed. The instrument includes a loop, which connects to the hemodialysis unit. Sensors are in the loop in series, so that the dialysis can flow through this loop and the sensors can acquisitive data of various parameters. In order to facilitate detection and carrying, the integrated circuit part modularly based on the ultralow-power microcontrollers,TI MSP430 is designed. High-performance and small-packaged components are used to establish a modular, high-precision, multi-functional, portable system. The functions and the key technical indexes of the instrument have reached the level of products abroad.

  9. Portable nuclear material detector and process

    Energy Technology Data Exchange (ETDEWEB)

    Hofstetter, Kenneth J (Aiken, SC); Fulghum, Charles K (Aiken, SC); Harpring, Lawrence J (North Augusta, SC); Huffman, Russell K (Augusta, GA); Varble, Donald L (Evans, GA)

    2008-04-01

    A portable, hand held, multi-sensor radiation detector is disclosed. The detection apparatus has a plurality of spaced sensor locations which are contained within a flexible housing. The detection apparatus, when suspended from an elevation, will readily assume a substantially straight, vertical orientation and may be used to monitor radiation levels from shipping containers. The flexible detection array can also assume a variety of other orientations to facilitate any unique container shapes or to conform to various physical requirements with respect to deployment of the detection array. The output of each sensor within the array is processed by at least one CPU which provides information in a usable form to a user interface. The user interface is used to provide the power requirements and operating instructions to the operational components within the detection array.

  10. MacBook Pro Portable Genius

    CERN Document Server

    Miser, Brad

    2011-01-01

    Tips and techniques for forward-thinking MacBook Pro users Now that you have a MacBook Pro, you need just one more accessory, your very own copy of MacBook Pro Portable Genius, Third Edition. This handy, compact book lets you in on a wealth of tips and tricks, so you get the very most out of Apple's very popular notebook. Discover the latest on the most recent release of iLife, get the skinny on the new Intel Core i7 and i5 processors in the Pro, see how to go wireless in a smart way, and much more. The book is easy to navigate, doesn't skimp on the essentials, and helps you save time and avoi

  11. The state of the art on the dry decontamination technologies applicable to highly radioactive contaminants and their needs for the national nuclear fuel cycle developent

    Energy Technology Data Exchange (ETDEWEB)

    Oh, Won Zin; Lee, K.W.; Won, H.J.; Jung, C.H.; Chol, W.K.; Kim, G.N.; Moon, J.K

    2000-12-01

    This report is intended to establish their needs to support the dry decontamination activities applicable to highly radioactive contaminants based on the requirement of technologies development suggested from the national nuclear fuel cycle projects, such as DUPIC, advanced spent fuel management and long-lived radionuclides conversion. The technology needs associated with decontamination addressed the requirements associated with the efficiency of decontamination technology, the reduction of secondary wastes, applicabilities and the remote operation. And also, Characterization and decontamination technologies for various contaminants are reviewed and analysed. Based on the assessment, Unit dry decontamination processes are selected and the schematic flow diagram for decontamination of highly radioactive contaminants.

  12. Opportunities for portable Ballard Fuel Cells

    Energy Technology Data Exchange (ETDEWEB)

    Voss, H.H.; Huff, J.R. [Ballard Power Systems Inc., Burnaby, British Columbia (Canada)

    1996-12-31

    With the increasing proliferation and sophistication of portable electronic devices in both commercial and military markets, the need has arisen for small, lightweight power supplies that can provide increased operating life over those presently available. A solution to this power problem is the development of portable Ballard Fuel Cell power systems that operate with a hydrogen fuel source and air. Ballard has developed PEM fuel cell stacks and power systems in the 25 to 100 watt range for both of these markets. For military use, Ballard has teamed with Ball Corporation and Hydrogen Consultants, Inc. and has provided the Ballard Fuel Cell stack for an ambient PEM fuel cell power system for the DoD. The system provides power from idle to I 00 watts and has the capability of delivering overloads of 125 watts for short periods of time. The system is designed to operate over a wide range of temperature, relative humidity and altitude. Hydrogen is supplied as a compressed gas, metal hydride or chemical hydride packaged in a unit that is mated to the power/control unit. The hydrogen sources provide 1.5, 5 and 15 kWh of operation, respectively. The design of the fuel cell power system enables the unit to operate at 12 volts or 24 volts depending upon the equipment being used. For commercial applications, as with the military, fuel cell power sources in the 25 to 500 watt range will be competing with advanced batteries. Ambient PEM fuel cell designs and demonstrators are being developed at 25 watts and other low power levels. Goals are minimum stack volume and weight and greatly enhanced operating life with reasonable system weight and volume. This paper will discuss ambient PEM fuel cell designs and performance and operating parameters for a number of power levels in the multiwatt range.

  13. Disposable cartridge biosensor platform for portable diagnostics

    Science.gov (United States)

    Yaras, Yusuf S.; Cakmak, Onur; Gunduz, Ali B.; Saglam, Gokhan; Olcer, Selim; Mostafazadeh, Aref; Baris, Ibrahim; Civitci, Fehmi; Yaralioglu, Goksen G.; Urey, Hakan

    2017-03-01

    We developed two types of cantilever-based biosensors for portable diagnostics applications. One sensor is based on MEMS cantilever chip mounted in a microfluidic channel and the other sensor is based on a movable optical fiber placed across a microfluidic channel. Both types of sensors were aimed at direct mechanical measurement of coagulation time in a disposable cartridge using plasma or whole blood samples. There are several similarities and also some important differences between the MEMS based and the optical fiber based solutions. The aim of this paper is to provide a comparison between the two solutions and the results. For both types of sensors, actuation of the cantilever or the moving fiber is achieved using an electro coil and the readout is optical. Since both the actuation and sensing are remote, no electrical connections are required for the cartridge. Therefore it is possible to build low cost disposable cartridges. The reader unit for the cartridge contains light sources, photodetectors, the electro coil, a heater, analog electronics, and a microprocessor. The reader unit has different optical interfaces for the cartridges that have MEMS cantilevers and moving fibers. MEMS based platform has better sensitivity but optomechanical alignment is a challenge and measurements with whole blood were not possible due to high scattering of light by the red blood cells. Fiber sensor based platform has relaxed optomechanical tolerances, ease of manufacturing, and it allows measurements in whole blood. Both sensors were tested using control plasma samples for activated-Partial-Thromboplastin-Time (aPTT) measurements. Control plasma test results matched with the manufacturer's datasheet. Optical fiber based system was tested for aPTT tests with human whole blood samples and the proposed platform provided repeatable test results making the system method of choice for portable diagnostics.

  14. Portable sensor technology for rotational ground motions

    Science.gov (United States)

    Bernauer, Felix; Wassermann, Joachim; Guattari, Frédéric; Igel, Heiner

    2016-04-01

    In this contribution we present performance characteristics of a single component interferometric fiber-optic gyroscope (IFOG). The prototype sensor is provided by iXBlue, France. It is tested in the framework of the European Research Council Project, ROMY (Rotational motions - a new observable for seismology), on its applicability as a portable and field-deployable sensor for rotational ground motions. To fully explore the benefits of this new seismic observable especially in the fields of vulcanology, ocean generated noise and geophysical exploration, such a sensor has to fulfill certain requirements regarding portability, power consumption, time stamping stability and dynamic range. With GPS-synchronized time stamping and miniseed output format, data acquisition is customized for the use in seismology. Testing time stamping accuracy yields a time shift of less than 0.0001 s and a correlation coefficient of 0.99 in comparison to a commonly used data acquisition system, Reftek 120. Sensor self-noise is below 5.0 ṡ 10-8 rads-1Hz-1/2 for a frequency band from 0.001 Hz to 5.0 Hz. Analysis of Allan deviation shows an angle random walk of 3.5 ṡ 10-8 rads-1Hz-1/2. Additionally, the operating range diagram is shown and ambient noise analysis is performed. The sensitivity of sensor self-noise to variations in surrounding temperature and magnetic field is tested in laboratory experiments. With a power consumption of less than 10 W, the whole system (single component sensor + data acquisition) is appropriate for field use with autonomous power supply.

  15. Decontamination of drinking water by direct heating in solar panels.

    Science.gov (United States)

    Fjendbo Jørgensen, A J; Nøhr, K; Sørensen, H; Boisen, F

    1998-09-01

    A device was developed for direct heating of water by solar radiation in a flow-through system of copper pipes. An adjustable thermostat valve prevents water below the chosen temperature from being withdrawn. The results show that it is possible to eliminate coliform and thermotolerant coliform bacteria from naturally contaminated river water by heating to temperatures of 65 degrees C or above. Artificial additions of Salmonella typhimurium, Streptococcus faecalis and Escherichia coli to contaminated river water were also inactivated after heating to 65 degrees C and above. The total viable count could be reduced by a factor of 1000. The heat-resistant bacteria isolated from the Mlalakuva River (Tanzania) were spore-forming bacteria which exhibited greater heat resistance than commonly used test bacteria originating from countries with colder climates. To provide a good safety margin it is recommended that an outlet water temperature of 75 degrees C be used. At that temperature the daily production was about 501 of decontaminated water per m2 of solar panel, an amount that could be doubled by using a heat exchanger to recycle the heat.

  16. Irradiation disinfestation and decontamination of Iranian dates and pistachio nuts

    Science.gov (United States)

    Zare, Z.; Sayhoon, M.; Maghsoudi, V.

    1993-07-01

    Decontamination and disinfestation effect of gamma radiation on microflora of dates and artificially infested packed dates (Mazafaty, Zard and Sayer variety) with Tribolium Confusum, Oryzaephilus Surinamensis and Ephestia Cautella in different stages studied. Treatment with 0.75 kGy dose of gamma radiation leads to complete and satisfactory insect disinfestation of dates during a storage period of 9, 20 and 35 days. This study shows that microbiological quality of Mazafaty dates can be significantly improved when they have received a gamma radiation dose of 2.5 kGy. Finally the sugar content of irradiated and unirradiated samples have compared. In this study, we have also used gamma radiation treatment for the control of microbial spoilage of pistachio nuts caused by toxigenic Aspergillus Flavus. The first sequence involved, the freshly harvested pistachio nuts inoculated with A. Flavus spores and exposed to radiation treatment, then retention of samples in a environmental chamber, set at temperature of 15-20 C at 75-80% relative humidity and stored for six months. In the second sequence during the storage period the changes in protein, lipid content of pistachio nuts have analyzed.

  17. Pulmonary decontamination for photodynamic inactivation with extracorporeal illumination

    Science.gov (United States)

    Geralde, Mariana C.; Leite, Ilaiáli S.; Inada, Natalia M.; Grecco, Clóvis; Medeiros, Alexandra I.; Kurachi, Cristina; Bagnato, Vanderlei S.

    2014-03-01

    Infectious pneumonia is a major cause of morbidity and mortality, despite advances in diagnostics and therapeutics in pulmonary infections. One of the major difficulties associated with the infection comes from the high rate of antibiotic resistant microorganisms, claiming for the use of alternative techniques with high efficiency and low cost. The photodynamic inactivation (PDI) is emerging as one of the great possibilities in this area, once its action is oxidative, not allowing microorganism develops resistance against the treatment. PDI for decontamination pulmonary has potential for treatment or creating better conditions for the action of antibiotics. In this study, we are developing a device to implement PDI for the treatment of lung diseases with extracorporeal illumination. To validate our theory, we performed measurements in liquid phantom to simulate light penetration in biological tissues at various fluency rates, the temperature was monitored in a body of hairless mice and the measurements of light transmittance in this same animal model. A diode laser emitting at 810 nm in continuous mode was used. Our results show 70% of leakage at 0.5 mm of thickness in phantom model. The mouse body temperature variation was 5.4 °C and was observed light transmittance through its chest. These results are suggesting the possible application of the extracorporeal illumination using infrared light source. Based on these findings, further studies about photodynamic inactivation will be performed in animal model using indocyanine green and bacteriochlorin as photosensitizers. The pulmonary infection will be induced with Streptococcus pneumoniae and Klebsiella pneumoniae.

  18. [Decontamination and antidotes in acute cases of poisoning].

    Science.gov (United States)

    Kupferschmidt, Hugo; Züst, Ariane; Rauber-Lüthy, Christine

    2009-05-01

    In acute poisoning the maintenance or reconstitution of vital functions is the first and most critical action. All subsequent therapies and the prognosis depend on the identification of the causative agent and on information about substance-specific toxicity. Despite incomplete evidence the concept of harm reduction by decreased absorption of the toxicants and by shortening the course of illness is consistent with toxicokinetic-dynamic principles and is therefore still used by clinical toxicologists. All these treatment options have to be seen within the context of the prognosis and the time course of an individual case of poisoning. Treatment options of gastrointestinal decontamination are (in decreasing order of importance) single-dose activated charcoal, whole bowel irritation, and gastric lavage. Induced emesis by ipecac syrup is not practiced anymore. Enhanced elimination techniques are multiple-dose activated charcoal, urine alkalinization, and extracorporeal techniques such as hemodialysis and hemoperfusion. Enhanced elimination is only beneficial in toxicants with long half-life. Antidotes are directed against specific agents and therefore may be used only in a limited number of cases. The procurement of specific antidotes, often hardly available and not approved, is facilitated if the supply is organized in a transparent and standardized manner.

  19. Practical means for decontamination 9 years after a nuclear accident

    Energy Technology Data Exchange (ETDEWEB)

    Roed, J.; Andersson, K.G.; Prip, H. [eds.

    1995-12-01

    Nine years after the Chernobyl accident, the contamination problems of the most severely affected areas remain unsolved. As a consequence of this, large previously inhabited areas and areas of farmland now lie deserted. An international group of scientists funded by the EU European Collaboration Programme (ECP/4) has investigated in practice a great number of feasible means to solve the current problems. The basic results of this work group are presented in this report that was prepared in a format which facilitates an intercomparison (cost-benefit analysis) of the individual examined techniques for decontamination or dose reduction in various different types of environmental scenarios. Each file containing information on a method or procedure was created by the persons and institutes responsible for the practical trial. Although the long period that has elapsed since the contamination took place has added to the difficulties in removing the radioactive matter, it could be concluded that many of the methods are still capable of reducing the dose level substantially. (au).

  20. Electrokinetics and soil decontamination: concepts and overview (Review

    Directory of Open Access Journals (Sweden)

    Mohammed A. Karim

    2014-12-01

    Full Text Available Electrokinetic decontamination and extraction have been proven to be one of the most viable, cost effective and emerging techniques in removing contaminants, especially heavy metals from soils for about last five decades. Basic concepts and an overview of the electrokinetic extraction processes and their potential applications in geotechnical and geoenvironmental engineering have been reviewed based on the literature and presented in this paper. Primarily, theoretical and laboratory experimental studies related to electroreclamation of soils are summarised in brief with basic concepts of electrokinetic processes. The paper has been divided into different sections that include history of electrokinetics, background and concepts, modelling, parameter effects, instrumentation, contaminant extraction, field applications, and summary and recommendation. Based on the review it is obvious that the field application of electrokinetic technology to remediate heavy metal contaminated soils /sediments is very limited and site specific. Additional laboratory studies and more pilot- and full-scale information from field applications are critical to the further understanding of the technology and to customize the process in different field conditions.

  1. DECONTAMINATING AND PROCESSING DREDGED MATERIAL FOR BENEFICIAL USE

    Energy Technology Data Exchange (ETDEWEB)

    CLESCERI,N.L.; STERN,E.A.; FENG,H.; JONES,K.W.

    2000-07-01

    Management of contaminated dredged material is a major problem in the Port of New York and New Jersey. One component of an overall management plan can be the application of a decontamination technology followed by creation of a product suitable for beneficial use. This concept is the focus of a project now being carried out by the US Environmental Protection Agency-Region 2, the US Army Corps of Engineers-New York District, the US Department of Energy-Brookhaven National Laboratory, and regional university groups that have included Rensselaer Polytechnic Institute, Rutgers University, New Jersey Institute of Technology, and Stevens Institute of Technology. The project has gone through phased testing of commercial technologies at the bench scale (15 liters) and pilot scale (1.5--500 m{sup 3}) levels. Several technologies are now going forward to large-scale demonstrations that are intended to treat from 23,000 to 60,000 m{sup 3}. Selections of the technologies were made based on the effectiveness of the treatment process, evaluation of the possible beneficial use of the treated materials, and other factors. Major elements of the project are summarized here.

  2. Protocol for seaweed decontamination to isolate unialgal cultures

    Directory of Open Access Journals (Sweden)

    Daniela R. P. Fernandes

    2011-04-01

    Full Text Available Decontamination protocols in seaweeds are essential tools for ecophysiological studies in laboratory cultures. These protocols consist of a set of procedures and physical and chemical treatments that must be adjusted for each species. Thus, the effects of explant size and of combinations of physical treatments (brushing and cutting and chemical treatments (sodium hypochlorite, detergent, seawater, distilled water, germanium dioxide on the process of obtaining unialgal culture of two pigmentar morphos of Hypnea musciformis were investigated. It was found that thallus segments 50 mm in length, when transported from the field to the laboratory, remained healthier and were less susceptible to epiphytes than those 7 mm in length. The collected material had surfaces contaminated by diatoms, which were weakly attached, as well as surface contamination caused by strongly attached Sahlingia subintegra. The most efficient combination of physical and chemical treatments was explant brushing, cutting and washing with detergent. This combination eliminated the contamination by S. subintegra, but not all of the diatom contamination. The population of the latter was reduced by using physical treatment and by washing with detergent and distilled water and then exterminated by using germanium dioxide (0.003 mg/L. Employing this protocol, unialgal cultures of H. musciformis could be established in approximately eight to ten weeks.

  3. Development of Novel Decontamination Techniques for Chemical Agents (GB, VX, HD) Contaminated Facilities. Phase II. Laboratory Evaluation of Novel Agent Decontamination Concepts

    Science.gov (United States)

    1985-06-21

    Frijlink, C., "Degradation of S-2-di-isopropyla- minoethyl O-ethyl Methylphosphonothioate in Soil:Sulphur Containing Products", Pestic . Science, 8, 510-514...Soil:Phosphorus Containing Products", Pestic . Science, 7, 355-362 (1976). 586 ............ APPENDIX VIII SUBTASK 10. JACADS DECONTAMINANT DATA BASE 587

  4. Evaluation of microwave steam bags for the decontamination of filtering facepiece respirators.

    Directory of Open Access Journals (Sweden)

    Edward M Fisher

    Full Text Available Reusing filtering facepiece respirators (FFRs has been suggested as a strategy to conserve available supplies for home and healthcare environments during an influenza pandemic. For reuse to be possible, used FFRs must be decontaminated before redonning to reduce the risk of virus transmission; however, there are no approved methods for FFR decontamination. An effective method must reduce the microbial threat, maintain the function of the FFR, and present no residual chemical hazard. The method should be readily available, inexpensive and easily implemented by healthcare workers and the general public. Many of the general decontamination protocols used in healthcare and home settings are unable to address all of the desired qualities of an efficient FFR decontamination protocol. The goal of this study is to evaluate the use of two commercially available steam bags, marketed to the public for disinfecting infant feeding equipment, for FFR decontamination. The FFRs were decontaminated with microwave generated steam following the manufacturers' instructions then evaluated for water absorption and filtration efficiency for up to three steam exposures. Water absorption of the FFR was found to be model specific as FFRs constructed with hydrophilic materials absorbed more water. The steam had little effect on FFR performance as filtration efficiency of the treated FFRs remained above 95%. The decontamination efficacy of the steam bag was assessed using bacteriophage MS2 as a surrogate for a pathogenic virus. The tested steam bags were found to be 99.9% effective for inactivating MS2 on FFRs; however, more research is required to determine the effectiveness against respiratory pathogens.

  5. Evaluation of microwave steam bags for the decontamination of filtering facepiece respirators.

    Science.gov (United States)

    Fisher, Edward M; Williams, Jessica L; Shaffer, Ronald E

    2011-04-15

    Reusing filtering facepiece respirators (FFRs) has been suggested as a strategy to conserve available supplies for home and healthcare environments during an influenza pandemic. For reuse to be possible, used FFRs must be decontaminated before redonning to reduce the risk of virus transmission; however, there are no approved methods for FFR decontamination. An effective method must reduce the microbial threat, maintain the function of the FFR, and present no residual chemical hazard. The method should be readily available, inexpensive and easily implemented by healthcare workers and the general public. Many of the general decontamination protocols used in healthcare and home settings are unable to address all of the desired qualities of an efficient FFR decontamination protocol. The goal of this study is to evaluate the use of two commercially available steam bags, marketed to the public for disinfecting infant feeding equipment, for FFR decontamination. The FFRs were decontaminated with microwave generated steam following the manufacturers' instructions then evaluated for water absorption and filtration efficiency for up to three steam exposures. Water absorption of the FFR was found to be model specific as FFRs constructed with hydrophilic materials absorbed more water. The steam had little effect on FFR performance as filtration efficiency of the treated FFRs remained above 95%. The decontamination efficacy of the steam bag was assessed using bacteriophage MS2 as a surrogate for a pathogenic virus. The tested steam bags were found to be 99.9% effective for inactivating MS2 on FFRs; however, more research is required to determine the effectiveness against respiratory pathogens.

  6. Self-care Decontamination within a Chemical Exposure Mass-casualty Incident.

    Science.gov (United States)

    Monteith, Raymond G; Pearce, Laurie D R

    2015-06-01

    Growing awareness and concern for the increasing frequency of incidents involving hazardous materials (HazMat) across a broad spectrum of contaminants from chemical, biological, radiological, and nuclear (CBRN) sources indicates a clear need to refine the capability to respond successfully to mass-casualty contamination incidents. Best results for decontamination from a chemical agent will be achieved if done within minutes following exposure, and delays in decontamination will increase the length of time a casualty is in contact with the contaminate. The findings presented in this report indicate that casualties involved in a HazMat/CBRN mass-casualty incident (MCI) in a typical community would not receive sufficient on-scene care because of operational delays that are integral to a standard HazMat/CBRN first response. This delay in response will mean that casualty care will shift away from the incident scene into already over-tasked health care facilities as casualties seek aid on their own. The self-care decontamination protocols recommended here present a viable option to ensure decontamination is completed in the field, at the incident scene, and that casualties are cared for more quickly and less traumatically than they would be otherwise. Introducing self-care decontamination procedures as a standard first response within the response community will improve the level of care significantly and provide essential, self-care decontamination to casualties. The process involves three distinct stages which should not be delayed; these are summarized by the acronym MADE: Move/Assist, Disrobe/Decontaminate, Evaluate/Evacuate.

  7. Chemical System Decontamination at PWR Power Stations Biblis A and B by Advanced System Decontamination by Oxidizing Chemistry (ASDOC-D) Process Technology - 13081

    Energy Technology Data Exchange (ETDEWEB)

    Loeb, Andreas; Runge, Hartmut; Stanke, Dieter [NIS Ingenieurgesellschaft mbH, Industriestrasse 13, 63755 Alzenau (Germany); Bertholdt, Horst-Otto [NCT Consulting, Leonhardstrasse 16-18, 90443 Nuernberg (Germany); Adams, Andreas; Impertro, Michael; Roesch, Josef [RWE Power, 68643 Biblis (Germany)

    2013-07-01

    For chemical decontamination of PWR primary systems the so called ASDOC-D process has been developed and qualified at the German PWR power station Biblis. In comparison to other chemical decontamination processes ASDOC-D offers a number of advantages: - ASDOC-D does not require separate process equipment but is completely operated and controlled by the nuclear site installations. Feeding of chemical concentrates into the primary system is done by means of the site's dosing systems. Process control is performed by standard site instrumentation and analytics. - ASDOC-D safely prevents any formation and precipitation of insoluble constituents - Since ASDOC-D is operated without external equipment there is no need for installation of such equipment in high radioactive radiation surrounding. The radioactive exposure rate during process implementation and process performance may therefore be neglected in comparison to other chemical decontamination processes. - ASDOC-D does not require auxiliary hose connections which usually bear high leakage risk. The above mentioned technical advantages of ASDOC-D together with its cost-effectiveness gave rise to Biblis Power station to agree on testing ASDOC-D at the volume control system of PWR Biblis unit A. By involving the licensing authorities as well as expert examiners into this test ASDOC-D received the official qualification for primary system decontamination in German PWR. As a main outcome of the achieved results NIS received contracts for full primary system decontamination of both units Biblis A and B (each 1.200 MW) by end of 2012. (authors)

  8. Evaluation of Decontamination Factor of Aerosol in Pool Scrubber according to Bubble Shape and Size

    Energy Technology Data Exchange (ETDEWEB)

    Jo, Hyun Joung; Ha, Kwang Soon; Jang, Dong Soon [KAERI, Daejeon (Korea, Republic of)

    2016-05-15

    The scrubbing pool could play an important role in the wet type FCVS because a large amount of aerosol is captured in the water pool. The pool scrubbing phenomena have been modelled and embedded in several computer codes, such as SPARC (Suppression Pool Aerosol Removal Code), BUSCA (BUbble Scrubbing Algorithm) and SUPRA (Suppression Pool Retention Analysis). These codes aim at simulating the pool scrubbing process and estimating the decontamination factors (DFs) of the radioactive aerosol and iodine gas in the water pool, which is defined as the ratio of initial mass of the specific radioactive material to final massy after passing through the water pool. The pool scrubbing models were reviewed and an aerosol scrubbing code has been prepared to calculate decontamination factor through the pool. The developed code has been verified using the experimental results and parametric studies the decontamination factor according to bubble shape and size. To evaluate the decontamination factor more accurate whole pool scrubber phenomena, the code was improved to consider the variety shape and size of bubbles. The decontamination factor were largely evaluated in ellipsoid bubble rather than in sphere bubble. The pool scrubbing models will be enhanced to apply more various model such as aerosol condensation of hygroscopic. And, it is need to experiment to measure to bubble shape and size distribution in pool to improve bubble model.

  9. The separation of silica nanoparticle by cetyltrimethylammonium bromide from decontamination foam waste

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Man Soo; Yoon, In Ho; Jung, Chong Hun; Moon, Jei Kwon; Choi, Wang Kyu [KAERI, Daejeon (Korea, Republic of)

    2016-05-15

    Decontamination foam has been considered as a potential application for the cleaning of radioactive contaminant in the field of metallic walls, overhead surfaces, and complex components. Moreover, foam decontamination could generate the low secondary waste amount owing to its volume expansion. In order to increase the decontamination efficiency, it is essential to improve the foam stability with low amount of chemical decontamination agent. Yoon et al. reported that the silica nanoparticle containing surfactant increased the foam stability compared to only surfactant solution[3]. Nanoparticle has been used with surfactant, which they adsorb at fluid/fluid interface, to stabilize emulsions or bubbles in foams. Despite of improving foam stability, they still used the surfactant, silica nanoparticle (1 wt%), and viscosifier. In addition, it is difficult to separate silica nanoparticle from decontamination solution. Because nanoparticles differ from classical solid particles due to smaller particle size and their specific properties. Thus, the separation method for nanoparticle should be also developed with high recovery rates. The flocculation of silica nanoparticle added by CTAB could be quickly achieved for only 30 min. The particle size of SiO{sub 2} was larger as CTAB amount increased, and SiO{sub 2} contents in the top solution were decreased after centrifugation.

  10. Analysis of the application of decontamination technologies to radioactive metal waste minimization using expert systems

    Energy Technology Data Exchange (ETDEWEB)

    Bayrakal, Suna [Iowa State Univ., Ames, IA (United States)

    1993-09-30

    Radioactive metal waste makes up a significant portion of the waste currently being sent for disposal. Recovery of this metal as a valuable resource is possible through the use of decontamination technologies. Through the development and use of expert systems a comparison can be made of laser decontamination, a technology currently under development at Ames Laboratory, with currently available decontamination technologies for applicability to the types of metal waste being generated and the effectiveness of these versus simply disposing of the waste. These technologies can be technically and economically evaluated by the use of expert systems techniques to provide a waste management decision making tool that generates, given an identified metal waste, waste management recommendations. The user enters waste characteristic information as input and the system then recommends decontamination technologies, determines residual contamination levels and possible waste management strategies, carries out a cost analysis and then ranks, according to cost, the possibilities for management of the waste. The expert system was developed using information from literature and personnel experienced in the use of decontamination technologies and requires validation by human experts and assignment of confidence factors to the knowledge represented within.

  11. An electrochemical and high-speed imaging study of micropore decontamination by acoustic bubble entrapment.

    Science.gov (United States)

    Offin, Douglas G; Birkin, Peter R; Leighton, Timothy G

    2014-03-14

    Electrochemical and high-speed imaging techniques are used to study the abilities of ultrasonically-activated bubbles to clean out micropores. Cylindrical pores with dimensions (diameter × depth) of 500 μm × 400 μm (aspect ratio 0.8), 125 μm × 350 μm (aspect ratio 2.8) and 50 μm × 200 μm (aspect ratio 4.0) are fabricated in glass substrates. Each pore is contaminated by filling it with an electrochemically inactive blocking organic material (thickened methyl salicylate) before the substrate is placed in a solution containing an electroactive species (Fe(CN)6(3-)). An electrode is fabricated at the base of each pore and the Faradaic current is used to monitor the decontamination as a function of time. For the largest pore, decontamination driven by ultrasound (generated by a horn type transducer) and bulk fluid flow are compared. It is shown that ultrasound is much more effective than flow alone, and that bulk fluid flow at the rates used cannot decontaminate the pore completely, but that ultrasound can. In the case of the 125 μm pore, high-speed imaging is used to elucidate the cleaning mechanisms involved in ultrasonic decontamination and reveals that acoustic bubble entrapment is a key feature. The smallest pore is used to explore the limits of decontamination and it is found that ultrasound is still effective at this size under the conditions employed.

  12. Study on magnetic separation for decontamination of cesium contaminated soil by using superconducting magnet

    Energy Technology Data Exchange (ETDEWEB)

    Igarashi, Susumu, E-mail: igarashi@qb.see.eng.osaka-u.ac.jp; Nomura, Naoki; Mishima, Fumihito; Akiyama, Yoko, E-mail: yoko-ak@see.eng.osaka-u.ac.jp

    2014-09-15

    Highlights: • The method for the soil decontamination by the superconducting magnet is proposed. • Magnetic separation of clay minerals was performed by HGMS. • Soil separation ratio was evaluated by quantitative analysis using XRD. • It is expected that HGMS can be applied to the actual soil decontamination. - Abstract: The accident of Fukushima Daiichi nuclear power plant caused the diffusion of radioactive cesium over the wide area. We examined the possibility of applying magnetic separation method using the superconducting magnet, which can process a large amount of the soil in high speed, to the soil decontamination and volume reduction of the radioactive cesium contaminated soil. Clay minerals are classified as 2:1 and 1:1 types by the difference of their layer structures, and these types of minerals are respectively paramagnetic and diamagnetic including some exception. It is known that most of the radioactive cesium is strongly adsorbed on the clay, especially on 2:1 type clay minerals. It is expected that the method which can separate only 2:1 type clay minerals selectively from the mixture clay minerals can enormously contribute to the volume reduction of the contaminated soil. In this study, the components in the clay before and after separation were evaluated to estimate the magnetic separation efficiency by using X-ray diffraction. From the results, the decontamination efficiency and the volume reduction ratio were estimated in order to examine the appropriate separation conditions for the practical decontamination of the soil.

  13. Development of an assessment instrument to evaluate performance of the skill of decontamination.

    Science.gov (United States)

    Farra, Sharon; Smith, Sherrill; French, DeAnne; Gillespie, Gordon

    2015-10-01

    Nurses must competently demonstrate psychomotor skills. Few reliable and valid instruments are available for psychomotor evaluation for disaster skills, including the skill of decontamination. The purpose of this study was to develop and refine an instrument to measure the skill of decontamination. A seven step instrument development design was implemented that included content validity and reliability as well as inter-rater reliability analysis. A convenience sample of approximately 140 participants was drawn from two colleges of nursing at two large academic universities. The sample included senior nursing students in either their community or final practicum nursing course. Based on a sample of 140 students who participated in a decontamination training experience using virtual reality simulation, a seven step established process for assessment of reliability and validity was implemented to develop a checklist for the skill of decontamination. The final instrument statistics: Content Validity Index for the overall instrument score was 0.94, Internal consistency coefficient=0.607(KR-20) and Inter-rater reliability=0.9114. This instrument provides a reliable and valid assessment of nurses' competency in performing the skill of decontamination offering a template for educators to develop similar tools. Copyright © 2015 Elsevier Ltd. All rights reserved.

  14. Evaluation of the biological efficacy of hydrogen peroxide vapour decontamination in wards of an Australian hospital.

    Science.gov (United States)

    Chan, H-T; White, P; Sheorey, H; Cocks, J; Waters, M-J

    2011-10-01

    This study assessed the efficacy of a 'dry' hydrogen peroxide vapour decontamination in an Australian hospital via a two-armed study. The in vivo arm examined the baseline bacterial counts in high-touch zones within wards and evaluated the efficacy of cleaning with a neutral detergent followed by either hydrogen peroxide vapour decontamination, or a manual terminal clean with bleach or Det-Sol 500. The in vitro arm examined the efficacy of hydrogen peroxide vapour decontamination on a variety of different surfaces commonly found in the wards of an Australian hospital, deliberately seeded with a known concentration of vancomycin-resistant enterococci (VRE). All bacterial counts were evaluated by a protocol of contact plate method. In the in vivo arm, 33.3% of the high-touch areas assessed had aerobic bacterial count below the detection limit (i.e. no bacteria recoverable) post hydrogen peroxide decontamination, and in all circumstances the highest microbial density was ≤3 cfu/cm(2), while in the in vitro arm there was at least a reduction in bacterial load by a factor of 10 at all surfaces investigated. These results showed that dry hydrogen peroxide vapour room decontamination is highly effective on a range of surfaces, although the cleanliness data obtained by these methods cannot be easily compared among the different surfaces as recovery of organisms is affected by the nature of the surface.

  15. Next Generation Non-particulate Dry Nonwoven Pad for Chemical Warfare Agent Decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Ramkumar, S S; Love, A; Sata, U R; Koester, C J; Smith, W J; Keating, G A; Hobbs, L; Cox, S B; Lagna, W M; Kendall, R J

    2008-05-01

    New, non-particulate decontamination materials promise to reduce both military and civilian casualties by enabling individuals to decontaminate themselves and their equipment within minutes of exposure to chemical warfare agents or other toxic materials. One of the most promising new materials has been developed using a needlepunching nonwoven process to construct a novel and non-particulate composite fabric of multiple layers, including an inner layer of activated carbon fabric, which is well-suited for the decontamination of both personnel and equipment. This paper describes the development of a composite nonwoven pad and compares efficacy test results for this pad with results from testing other decontamination systems. The efficacy of the dry nonwoven fabric pad was demonstrated specifically for decontamination of the chemical warfare blister agent bis(2-chloroethyl)sulfide (H or sulfur mustard). GC/MS results indicate that the composite fabric was capable of significantly reducing the vapor hazard from mustard liquid absorbed into the nonwoven dry fabric pad. The mustard adsorption efficiency of the nonwoven pad was significantly higher than particulate activated carbon (p=0.041) and was similar to the currently fielded US military M291 kit (p=0.952). The nonwoven pad has several advantages over other materials, especially its non-particulate, yet flexible, construction. This composite fabric was also shown to be chemically compatible with potential toxic and hazardous liquids, which span a range of hydrophilic and hydrophobic chemicals, including a concentrated acid, an organic solvent and a mild oxidant, bleach.

  16. Applying crowd psychology to develop recommendations for the management of mass decontamination.

    Science.gov (United States)

    Carter, Holly; Drury, John; Rubin, G James; Williams, Richard; Amlôt, Richard

    2015-01-01

    Mass decontamination is a public health intervention employed by emergency responders following a chemical, biological, or radiological release. It involves a crowd of people whose interactions with each other and with the emergency responders managing the incident are likely to affect the success of the decontamination process. The way in which members of the public collectively experience decontamination is likely to affect their behavior and hence is crucial to the success of the decontamination process. Consequently, responders and the responsible authorities need to understand crowd psychology during mass emergencies and disasters. Recently, the social identity approach to crowd psychology has been applied to explain public perceptions and behavior during mass emergencies. This approach emphasizes that crowd events are characteristically intergroup encounters, in which the behavior of one group can affect the perceptions and behavior of another. We summarize the results from a program of research in which the social identity approach was applied to develop and test recommendations for the management of mass decontamination. The findings from this program of research show that (1) responders' perceptions of crowd behavior matter; (2) participants value greater communication and this affects their compliance; and (3) social identity processes explain the relationship between effective responder communication and relevant outcome variables, such as public compliance, public cooperation, and public anxiety. Based on this program of research, we recommend 4 responder management strategies that focus on increasing public compliance, increasing orderly and cooperative behavior among members of the public, reducing public anxiety, and respecting public needs for privacy.

  17. A comparative study of infrared and microwave heating for microbial decontamination of paprika powder

    Directory of Open Access Journals (Sweden)

    Lovisa eEliasson

    2015-09-01

    Full Text Available There is currently a need in developing new decontamination technologies for spices due to limitations of existing technologies, mainly regarding their effects on spices’ sensory quality. In the search of new decontamination solutions, it is of interest to compare different technologies, to provide the industry with knowledge for taking decisions concerning appropriate decontamination technologies for spices. The present study compares infrared and microwave decontamination of naturally contaminated paprika powder after adjustment of water activity to 0.88. Infrared respectively microwave heating was applied to quickly heat up paprika powder to 98°C, after which the paprika sample was transferred to a conventional oven set at 98°C to keep the temperature constant during a holding time up to 20 min. In the present experimental set-up microwave treatment at 98°C for 20 min resulted in a reduction of 4.8 log units of the total number of mesophilic bacteria, while the infrared treatment showed a 1 log unit lower reduction for the corresponding temperature and treatment time. Microwave and infrared heating created different temperature profiles and moisture distribution within the paprika sample during the heating up part of the process, which is likely to have influenced the decontamination efficiency. The results of this study are used to discuss the difficulties in comparing two thermal technologies on equal conditions due to differences in their heating mechanisms.

  18. 324 and 325 Building hot cell cleanout program: Decontamination of C-Cell

    Energy Technology Data Exchange (ETDEWEB)

    Katayama, Y.B.; Holton, L.K. Jr.

    1989-10-01

    During FY 1989 the decontamination of C-Cell of Hanford's 324 Building was completed as part of the 324 and 325 Building Hot Cell Cleanout Program sponsored by the DOE Nuclear Energy's Surplus Facilities Management Program. The decontamination effort was completed using a series of remote and contact decontamination techniques. Initial radiation readings in C-Cell averaged 50 rad/hr and were reduced remotely to less than 200 mrad/hr using an alkaline foam cleaner followed by a 5000-psi water flush. Contact decontamination was then permissible using ultra high-pressure water, at 36,000 psi, further reducing the average radiation level in the cell to less than 86 mrem/hr. The approach used in decontaminating C-Cell resulted in a savings in radiation exposure of 87% and a cost savings of 39% compared to a hands-on procedure used in A-Cell, 324 Building in 1987. The radiation dose and the costs to achieve a 244-fold reduction in radiation contamination were 1.65 mrem per ft{sup 2} and $96 per ft{sup 2} of cell surface area. 14 figs., 4 tabs.

  19. All-Weather Hydrogen Peroxide-Based Decontamination of CBRN Contaminants

    Energy Technology Data Exchange (ETDEWEB)

    Wagner, George W. [U.S. Army Edgewood Chemical Biological Center (ECBC), Aberdeen Proving Ground, MD (United States); Procell, Lawrence R. [U.S. Army Edgewood Chemical Biological Center (ECBC), Aberdeen Proving Ground, MD (United States); Sorrick, David C. [U.S. Army Edgewood Chemical Biological Center (ECBC), Aberdeen Proving Ground, MD (United States); Lawson, Glenn E. [Naval Surface Warfare Center (NSWC), Dahlgren, VA (United States); Wells, Claire M. [Naval Surface Warfare Center (NSWC), Dahlgren, VA (United States); Reynolds, Charles M. [U.S. Army Cold Regions Research and Engineering Lab. (CRREL), Hanover, NH (United States); Ringelberg, D. B. [U.S. Army Cold Regions Research and Engineering Lab. (CRREL), Hanover, NH (United States); Foley, Karen L. [U.S. Army Cold Regions Research and Engineering Lab. (CRREL), Hanover, NH (United States); Lumetta, Gregg J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Blanchard, David L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2010-03-11

    A hydrogen peroxide-based decontaminant, Decon Green, is efficacious for the decontamination of chemical agents VX (S-2-(diisopropylamino)ethyl O-ethyl methylphosphonothioate), GD (Soman, pinacolyl methylphosphonofluoridate), and HD (mustard, bis(2-chloroethyl) sulfide); the biological agent anthrax (Bacillus anthracis); and radiological isotopes Cs-137 and Co-60; thus demonstrating the ability of this decontamination approach to ameliorate the aftermath of all three types of weapons of mass destruction (WMD). Reaction mechanisms afforded for the chemical agents are discussed as are rationales for the enhanced removal efficacy of recalcitrant 60Co on certain surfaces. Decontaminants of this nature can be deployed, and are effective, at very low temperatures (-32 °C), as shown for studies done with VX and HD simulants, without the need for external heat sources. Finally, the efficacy of a lower-logistics, dry decontaminant powder concentrate (utilizing the solid active-oxygen compounds peracetyl borate and Peroxydone) which can be reconstituted with water in the field prior to use, is presented.

  20. Portability of Prolog programs: theory and case-studies

    CERN Document Server

    Wielemaker, Jan

    2010-01-01

    (Non-)portability of Prolog programs is widely considered as an important factor in the lack of acceptance of the language. Since 1995, the core of the language is covered by the ISO standard 13211-1. Since 2007, YAP and SWI-Prolog have established a basic compatibility framework. This article describes and evaluates this framework. The aim of the framework is running the same code on both systems rather than migrating an application. We show that today, the portability within the family of Edinburgh/Quintus derived Prolog implementations is good enough to allow for maintaining portable real-world applications.