Demonstration of Intelligent Control and Fan Improvements in Computer Room Air Handlers

Energy Technology Data Exchange (ETDEWEB)

Coles, Henry [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Greenberg, Steve [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Vita, Corinne [Vigilent, Oakland, CA (United States)

2012-11-30

This report documents a demonstration of the energy-efficiency improvement provided by a new control system for computer room air handling devices. It also analyzes measured and reported air handling device fan power associated with changing the fan type. A 135,000 square foot commercial data center was used for the demonstration. All air handling units were upgraded with improved efficiency fans, and a control system that automatically adjusts the fan speed for the air handling units was added. Power measurements were collected for a baseline and for a period with the fan speed control system active. Changing the fan type resulted in a savings of 47 percent of energy used by the air handling equipment and associated chiller plant energy needed to cool the air handlers themselves. The addition of the fan speed control resulted in an additional 37 percent savings in the same two categories. The combined savings for the two improvements for the same categories was 66 percent compared to the data center fitted with the original fans without a control system. The energy use reduction provided by the complete air handling device improvement program for the whole data center site is estimated to be 2.9 million kilowatt hours per year—an overall data center site savings of 8.0 percent. The reduced electrical energy use at the site provides a 1.9 million pound yearly reduction of carbon dioxide emissions. This demonstration showed that fan upgrades and a control system addition provide cost-effective improvements for data centers, with a payback reported to be under two years without utility incentives. In addition to the control system providing energy savings, the data collection and visual analysis capabilities provided immediate and long-term benefits. It is recommended that data center operators consider investing in fan upgrades and/or adding fan speed control for computer room air handlers.

Waste processing of chemical cleaning solutions

International Nuclear Information System (INIS)

Peters, G.A.

1991-01-01

This paper reports on chemical cleaning solutions containing high concentrations of organic chelating wastes that are difficult to reduce in volume using existing technology. Current methods for evaporating low-level radiative waste solutions often use high maintenance evaporators that can be costly and inefficient. The heat transfer surfaces of these evaporators are easily fouled, and their maintenance requires a significant labor investment. To address the volume reduction of spent, low-level radioactive, chelating-based chemical cleaning solutions, ECOSAFE Liquid Volume Reduction System (LVRS) has been developed. The LVRS is based on submerged combustion evaporator technology that was modified for treatment of low-level radiative liquid wastes. This system was developed in 1988 and was used to process 180,000 gallons of waste at Oconee Nuclear Station

Residential Energy Efficiency Demonstration: Hawaii and Guam Energy Improvement Technology Demonstration Project

Energy Technology Data Exchange (ETDEWEB)

Earle, L. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Sparn, B. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Rutter, A. [Sustainability Solutions LLC (Guam); Briggs, D. [Naval Base Guam, Santa Rita (Guam)

2014-03-01

In order to meet its energy goals, the Department of Defense (DOD) has partnered with the Department of Energy (DOE) to rapidly demonstrate and deploy cost-effective renewable energy and energy-efficiency technologies. The scope of this project was to demonstrate tools and technologies to reduce energy use in military housing, with particular emphasis on measuring and reducing loads related to consumer electronics (commonly referred to as 'plug loads'), hot water, and whole-house cooling.

Evaluation of patients undergoing lung volume reduction surgery: Ancillary information available from computed tomography

International Nuclear Information System (INIS)

Cleverley, Joanne R.; Desai, Sujal R.; Wells, Athol U.; Koyama, Hiroshi; Eastick, Sian; Schmidt, Maria A.; Charrier, Clare L.; Gatehouse, Peter D.; Goldstraw, Peter; Pepper, John R.; Geddes, Duncan M.; Hansell, David M.

2000-01-01

AIM: A number of imaging techniques have been used for the pre-operative assessment of patients for lung volume reduction surgery (LVRS). We evaluated whether data currently acquired from perfusion scintigrams and cine MR of the diaphragm are obtainable from high resolution CT (HRCT) of the thorax. MATERIALS AND METHODS: Thirty patients taking part in a randomized controlled trial of LVRS against maximal medical therapy were evaluated. HRCT examinations (n= 30) were scored for (i) the extent and distribution of emphysema; (ii) the extent of normal pulmonary vasculature; and (iii) diaphragmatic contour, apparent defects and herniation. On scintigraphy, (n28), perfusion of the lower thirds of both lungs, as a proportion of total lung perfusion (LZ/T PERF ), was expressed as a percentage of predicted values (derived from 10 normal control subjects). On cine MR (n= 25) hemidiaphragmatic excursion and coordination were recorded. RESULTS: Extensive emphysema was present on HRCT (60% ± 13.2%). There was strong correlation between the extent of normal pulmonary vasculature on HRCT and on perfusion scanning (r s = 0.85, P< 0.00005). Hemidiaphragmatic incoordination on MR was weakly associated with hemidiaphragmatic eventration on HRCT (P0.04). CONCLUSION: The strong correlation between lung perfusion assessed by HRCT and lung perfusion on scintigraphy suggests that perfusion scintigraphy is superfluous in the pre-operative evaluation of patients with emphysema for LVRS. Cleverley, J.R. (2000)

Experimental demonstration of an improved EPON architecture using OFDMA for bandwidth scalable LAN emulation

DEFF Research Database (Denmark)

Deng, Lei; Zhao, Ying; Yu, Xianbin

2011-01-01

We propose and demonstrate an improved Ethernet passive optical network (EPON) architecture supporting bandwidth-scalable physical layer local area network (LAN) emulation. Due to the use of orthogonal frequency division multiple access (OFDMA) technology for the LAN traffic transmission, there i...

Improvement of Cerebral Hypoperfusion with Levothyroxine Therapy in Hashimoto's Encephalopathy Demonstrated by 99mTc-HMPAO-SPECT

Science.gov (United States)

Schnedl, Wolfgang J.; Mirzaei, Siroos; Wallner-Liebmann, Sandra J.; Tafeit, Erwin; Mangge, Harald; Krause, Robert; Lipp, Rainer W.

2013-01-01

Background Hashimoto's encephalopathy (HE) is a rare immune-mediated encephalopathy associated with autoimmune Hashimoto's thyroiditis. Objectives and Methods We report on a patient with HE and significant clinical improvement correlating with an increase in cerebral blood flow demonstrated by hexamethylpropyleneamine oxime (HMPAO) single-photon emission computed tomography (SPECT). HMPAO-SPECT was performed with 740 MBq of technetium-99m-HMPAO. To demonstrate the improvement in regional cerebral blood flow, individual regions of interest were drawn around visually diminished HMPAO uptake, the lesion to reference region ratio was calculated and transverse section images and semi-quantitative measurements were performed. Results We show a 5-year follow-up with significant clinical improvement, a 10-fold reduction in autoantibodies to thyroid peroxidase and an approximately 20% improvement in cerebral blood flow with HMPAO-SPECT. Conclusion Adequate levothyroxine treatment achieving and maintaining euthyroidism should be considered as therapy to lower autoantibodies and improve clinical outcome in patients with Hashimoto's thyroiditis and encephalopathy. PMID:24783049

Improving Your Exploratory Factor Analysis for Ordinal Data: A Demonstration Using FACTOR

Directory of Open Access Journals (Sweden)

James Baglin

2014-06-01

Full Text Available Exploratory factor analysis (EFA methods are used extensively in the field of assessment and evaluation. Due to EFA's widespread use, common methods and practices have come under close scrutiny. A substantial body of literature has been compiled highlighting problems with many of the methods and practices used in EFA, and, in response, many guidelines have been proposed with the aim to improve application. Unfortunately, implementing recommended EFA practices has been restricted by the range of options available in commercial statistical packages and, perhaps, due to an absence of clear, practical - how-to' demonstrations. Consequently, this article describes the application of methods recommended to get the most out of your EFA. The article focuses on dealing with the common situation of analysing ordinal data as derived from Likert-type scales. These methods are demonstrated using the free, stand-alone, easy-to-use and powerful EFA package FACTOR (http://psico.fcep.urv.es/utilitats/factor/, Lorenzo-Seva & Ferrando, 2006. The demonstration applies the recommended techniques using an accompanying dataset, based on the Big 5 personality test. The outcomes obtained by the EFA using the recommended procedures through FACTOR are compared to the default techniques currently available in SPSS.

Experimental demonstration of improved fiber nonlinearity tolerance for unique-word DFT-spread OFDM systems.

Science.gov (United States)

Chen, Xi; Li, An; Gao, Guanjun; Shieh, William

2011-12-19

In this paper we experimentally demonstrate transmission performance of optical DFT-spread OFDM systems in comparison with conventional OFDM systems. A 440.8-Gb/s superchannel consisting of 8 x 55.1-Gb/s densely-spaced DFT-S OFDM signal is successfully received after 1120-km transmission with a spectral efficiency of 3.5 b/s/Hz. It is shown that DFT-S OFDM can achieve an improvement of 1 dB in Q factor and 1 dB in launch power over conventional OFDM. Additionally, unique word aided phase estimation algorithm is proposed and demonstrated enabling extremely long OFDM symbol transmission.

Demonstration Technique to Improve Vocabulary and Grammar Element in Teaching Speaking at EFL Learners

Science.gov (United States)

Husnu, Muhammad

2018-01-01

This study aimed at examining the effectiveness of demonstration technique to improve vocabulary and grammar element in teaching speaking at EFL learners. This research applied true-experimental design. The respondents of the study were 32 students (class IIA) as experimental group and 32 students (class IIB) as control group from the second…

Demonstration of the improved PID method for the accurate temperature control of ADRs

International Nuclear Information System (INIS)

Shinozaki, K.; Hoshino, A.; Ishisaki, Y.; Mihara, T.

2006-01-01

Microcalorimeters require extreme stability (-bar 10μK) of thermal bath at low temperature (∼100mK). We have developed a portable adiabatic demagnetization refrigerator (ADR) system for ground experiments with TES microcalorimeters, in which we observed residual temperature between aimed and measured values when magnet current was controlled with the standard Proportional, Integral, and Derivative control (PID) method. The difference increases in time as the magnet current decreases. This phenomenon can be explained by the theory of the magnetic cooling, and we have introduced a new functional parameter to improve the PID method. With this improvement, long-term stability of the ADR temperature about 10μK rms is obtained up to the period of ∼15ks down to almost zero magnet current. We briefly describe our ADR system and principle of the improved PID method, showing the temperature control result. It is demonstrated that the controlled time of the aimed temperature can be extended by about 30% longer than the standard PID method in our system. The improved PID method is considered to be of great advantage especially in the range of small magnet current

Improvements to the Whoosh Bottle Rocket Car Demonstration

Science.gov (United States)

Campbell, Dean J.; Staiger, Felicia A.; Jujjavarapu, Chaitanya N.

2015-01-01

The whoosh bottle rocket car has been redesigned to be more reusable and more robust, making it even easier to use as a demonstration. Enhancements of this demonstration, including the use of heat sensitive ink and electronic temperature probes, enable users to find warmer and cooler regions on the surface of the whoosh bottle.

After The Demonstration: What States Sustained After the End of Federal Grants to Improve Children's Health Care Quality.

Science.gov (United States)

Ireys, Henry T; Brach, Cindy; Anglin, Grace; Devers, Kelly J; Burton, Rachel

2018-02-01

Introduction Under the CHIPRA Quality Demonstration Grant Program, CMS awarded $100 million through 10 grants that 18 state Medicaid agencies implemented between 2010 and 2015. The program's legislatively-mandated purpose was to evaluate promising ideas for improving the quality of children's health care provided through Medicaid and CHIP. As part of the program's multifaceted evaluation, this study examined the extent to which states sustained key program activities after the demonstration ended. Methods We identified 115 potentially sustainable elements within states' CHIPRA demonstrations and analyzed data from grantee reports and key informant interviews to assess sustainment outcomes and key influential factors. We also assessed sustainment of the projects' intellectual capital. Results 56% of potentially sustainable elements were sustained. Sustainment varied by topic area: Elements related to quality measure reporting and practice facilitation were more likely to be sustained than others, such as parent advisors. Broad contextual factors, the state's Medicaid environment, implementation partners' resources, and characteristics of the demonstration itself all shaped sustainment outcomes. Discussion Assessing sustainment of key elements of states' CHIPRA quality demonstration projects provides insight into the fates of the "promising ideas" that the grant program was designed to examine. As a result of the federal government's investment in this grant program, many demonstration states are in a strong position to extend and spread specific strategies for improving the quality of care for children in Medicaid and CHIP. Our findings provide insights for policymakers and providers working to improve the quality of health care for low income children.

Evaluation of Smart Grid Technologies Employed for System Reliability Improvement: Pacific Northwest Smart Grid Demonstration Experience

Energy Technology Data Exchange (ETDEWEB)

Agalgaonkar, Yashodhan P.; Hammerstrom, Donald J.

2017-06-01

The Pacific Northwest Smart Grid Demonstration (PNWSGD) was a smart grid technology performance evaluation project that included multiple U.S. states and cooperation from multiple electric utilities in the northwest region. One of the local objectives for the project was to achieve improved distribution system reliability. Toward this end, some PNWSGD utilities automated their distribution systems, including the application of fault detection, isolation, and restoration and advanced metering infrastructure. In light of this investment, a major challenge was to establish a correlation between implementation of these smart grid technologies and actual improvements of distribution system reliability. This paper proposes using Welch’s t-test to objectively determine and quantify whether distribution system reliability is improving over time. The proposed methodology is generic, and it can be implemented by any utility after calculation of the standard reliability indices. The effectiveness of the proposed hypothesis testing approach is demonstrated through comprehensive practical results. It is believed that wider adoption of the proposed approach can help utilities to evaluate a realistic long-term performance of smart grid technologies.

Lung Volume Reduction After Stereotactic Ablative Radiation Therapy of Lung Tumors: Potential Application to Emphysema

Energy Technology Data Exchange (ETDEWEB)

Binkley, Michael S. [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California (United States); Shrager, Joseph B. [Division of Thoracic Surgery, Department of Cardiothoracic Surgery, Stanford University School of Medicine, Stanford, California (United States); Stanford Cancer Institute, Stanford University School of Medicine, Stanford, California (United States); Leung, Ann N. [Department of Radiology, Stanford University School of Medicine, Stanford, California (United States); Popat, Rita [Department of Health Research and Policy, Stanford University School of Medicine, Stanford, California (United States); Trakul, Nicholas [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California (United States); Department of Radiation Oncology, University of Southern California Keck School of Medicine, Los Angeles, California (United States); Atwood, Todd F.; Chaudhuri, Aadel [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California (United States); Maxim, Peter G. [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California (United States); Stanford Cancer Institute, Stanford University School of Medicine, Stanford, California (United States); Diehn, Maximilian, E-mail: Diehn@Stanford.edu [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California (United States); Stanford Cancer Institute, Stanford University School of Medicine, Stanford, California (United States); Institute for Stem Cell Biology and Regenerative Medicine, Stanford University School of Medicine, Stanford, California (United States); Loo, Billy W., E-mail: BWLoo@Stanford.edu [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California (United States); Stanford Cancer Institute, Stanford University School of Medicine, Stanford, California (United States)

2014-09-01

Purpose: Lung volume reduction surgery (LVRS) improves dyspnea and other outcomes in selected patients with severe emphysema, but many have excessive surgical risk for LVRS. We analyzed the dose-volume relationship for lobar volume reduction after stereotactic ablative radiation therapy (SABR) of lung tumors, hypothesizing that SABR could achieve therapeutic volume reduction if applied in emphysema. Methods and Materials: We retrospectively identified patients treated from 2007 to 2011 who had SABR for 1 lung tumor, pre-SABR pulmonary function testing, and ≥6 months computed tomographic (CT) imaging follow-up. We contoured the treated lobe and untreated adjacent lobe(s) on CT before and after SABR and calculated their volume changes relative to the contoured total (bilateral) lung volume (TLV). We correlated lobar volume reduction with the volume receiving high biologically effective doses (BED, α/β = 3). Results: 27 patients met the inclusion criteria, with a median CT follow-up time of 14 months. There was no grade ≥3 toxicity. The median volume reduction of the treated lobe was 4.4% of TLV (range, −0.4%-10.8%); the median expansion of the untreated adjacent lobe was 2.6% of TLV (range, −3.9%-11.6%). The volume reduction of the treated lobe was positively correlated with the volume receiving BED ≥60 Gy (r{sup 2}=0.45, P=.0001). This persisted in subgroups determined by high versus low pre-SABR forced expiratory volume in 1 second, treated lobe CT emphysema score, number of fractions, follow-up CT time, central versus peripheral location, and upper versus lower lobe location, with no significant differences in effect size between subgroups. Volume expansion of the untreated adjacent lobe(s) was positively correlated with volume reduction of the treated lobe (r{sup 2}=0.47, P<.0001). Conclusions: We identified a dose-volume response for treated lobe volume reduction and adjacent lobe compensatory expansion after lung tumor SABR, consistent across

After The Demonstration: What States Sustained After the End of Federal Grants to Improve Children’s Health Care Quality

Science.gov (United States)

Brach, Cindy; Anglin, Grace; Devers, Kelly J.; Burton, Rachel

2018-01-01

Introduction Under the CHIPRA Quality Demonstration Grant Program, CMS awarded $100 million through 10 grants that 18 state Medicaid agencies implemented between 2010 and 2015. The program’s legislatively-mandated purpose was to evaluate promising ideas for improving the quality of children’s health care provided through Medicaid and CHIP. As part of the program’s multifaceted evaluation, this study examined the extent to which states sustained key program activities after the demonstration ended. Methods We identified 115 potentially sustainable elements within states’ CHIPRA demonstrations and analyzed data from grantee reports and key informant interviews to assess sustainment outcomes and key influential factors. We also assessed sustainment of the projects’ intellectual capital. Results 56% of potentially sustainable elements were sustained. Sustainment varied by topic area: Elements related to quality measure reporting and practice facilitation were more likely to be sustained than others, such as parent advisors. Broad contextual factors, the state’s Medicaid environment, implementation partners’ resources, and characteristics of the demonstration itself all shaped sustainment outcomes. Discussion Assessing sustainment of key elements of states’ CHIPRA quality demonstration projects provides insight into the fates of the “promising ideas” that the grant program was designed to examine. As a result of the federal government’s investment in this grant program, many demonstration states are in a strong position to extend and spread specific strategies for improving the quality of care for children in Medicaid and CHIP. Our findings provide insights for policymakers and providers working to improve the quality of health care for low income children. PMID:29119478

Demonstrating Success: Web Analytics and Continuous Improvement

Science.gov (United States)

Loftus, Wayne

2012-01-01

As free and low-cost Web analytics tools become more sophisticated, libraries' approach to user analysis can become more nuanced and precise. Tracking appropriate metrics with a well-formulated analytics program can inform design decisions, demonstrate the degree to which those decisions have succeeded, and thereby inform the next iteration in the…

Improving Web-Based Student Learning Through Online Video Demonstrations

Science.gov (United States)

Miller, Scott; Redman, S.

2010-01-01

Students in online courses continue to lag their peers in comparable face-to-face (F2F) courses (Ury 2004, Slater & Jones 2004). A meta-study of web-based vs. classroom instruction by Sitzmann et al (2006) discovered that the degree of learner control positively influences the effectiveness of instruction: students do better when they are in control of their own learning. In particular, web-based courses are more effective when they incorporate a larger variety of instructional methods. To address this need, we developed a series of online videos to demonstrate various astronomical concepts and provided them to students enrolled in an online introductory astronomy course at Penn State University. We found that the online students performed worse than the F2F students on questions unrelated to the videos (t = -2.84), but that the online students who watched the videos performed better than the F2F students on related examination questions (t = 2.11). We also found that the online students who watched the videos performed significantly better than those who did not (t = 3.43). While the videos in general proved helpful, some videos were more helpful than others. We will discuss our thoughts on why this might be, and future plans to improve upon this study. These videos are freely available on iTunesU, YouTube, and Google Video.

H2Oh!: Classroom demonstrations and activities for improving student learning of water concepts

Science.gov (United States)

Chan-Hilton, A.; Neupauer, R. M.; Burian, S. J.; Lauer, J. W.; Mathisen, P. P.; Mays, D. C.; Olson, M. S.; Pomeroy, C. A.; Ruddell, B. L.; Sciortino, A.

2012-12-01

Research has shown that the use of demonstrations and hands-on activities in the classroom enhances student learning. Students learn more and enjoy classes more when visual and active learning are incorporated into the lecture. Most college-aged students prefer visual modes of learning, while most instruction is conducted in a lecture, or auditory, format. The use of classroom demonstrations provides opportunities for incorporating visual and active learning into the classroom environment. However, while most instructors acknowledge the benefits of these teaching methods, they typically do not have the time and resources to develop and test such activities and to develop plans to incorporate them into their lectures. Members of the Excellence in Water Resources Education Task Committee of the Environmental and Water Resources Institute (EWRI) of the American Society of Civil Engineers (ASCE) have produced a publication that contains a collection of activities aimed to foster excellence in water resources and hydrology education and improve student learning of principles. The book contains forty-five demonstrations and activities that can be used in water-related classes with topics in fluid mechanics, hydraulics, surface water hydrology, groundwater hydrology, and water quality. We present examples of these activities, including topics such as conservation of momentum, buoyancy, Bernoulli's principle, drag force, pipe flow, watershed delineation, reservoir networks, head distribution in aquifers, and molecular diffusion in a porous medium. Unlike full laboratory exercises, these brief demonstrations and activities (most of which take less than fifteen minutes) can be easily incorporated into classroom lectures. For each demonstration, guidance for preparing and conducting the activity, along with a brief overview of the principles that are demonstrated, is provided. The target audience of the activities is undergraduate students, although the activities also may be

Improvement of shipborne sky radiometer and its demonstration aboard the Antarctic research vessel Shirase

Directory of Open Access Journals (Sweden)

Noriaki Tanaka

2014-11-01

Full Text Available The sun-tracking performance of a shipborne sky radiometer was improved to attain accurate aerosol optical thickness (AOT from direct solar measurements on a pitching and rolling vessel. Improvements were made in the accuracy of sun-pointing measurements, field-of-view expansion, sun-tracking speed, and measurement method. Radiometric measurements of direct solar and sky brightness distribution were performed using the shipborne sky radiometer onboard the Antarctic research vessel (R/V Shirase during JARE-51 (2009-2010 and JARE-52 (2010-2011. The temporal variation of signal intensity measured by the radiometer under cloudless conditions was smooth, demonstrating that the radiometer could measure direct sunlight onboard the R/V. AOT at 500 nm ranged from 0.01 to 0.34, and values over Southeast Asia and over the western Pacific Ocean in spring were higher than those over other regions. The Angstrom exponent ranged from －0.06 to 2.00, and values over Southeast Asia and off the coast near Sydney were the highest. The improved shipborne sky radiometer will contribute to a good understanding of the nature of aerosols over the ocean.

Demonstration of improved seismic source inversion method of tele-seismic body wave

Science.gov (United States)

Yagi, Y.; Okuwaki, R.

2017-12-01

Seismic rupture inversion of tele-seismic body wave has been widely applied to studies of large earthquakes. In general, tele-seismic body wave contains information of overall rupture process of large earthquake, while the tele-seismic body wave is inappropriate for analyzing a detailed rupture process of M6 7 class earthquake. Recently, the quality and quantity of tele-seismic data and the inversion method has been greatly improved. Improved data and method enable us to study a detailed rupture process of M6 7 class earthquake even if we use only tele-seismic body wave. In this study, we demonstrate the ability of the improved data and method through analyses of the 2016 Rieti, Italy earthquake (Mw 6.2) and the 2016 Kumamoto, Japan earthquake (Mw 7.0) that have been well investigated by using the InSAR data set and the field observations. We assumed the rupture occurring on a single fault plane model inferred from the moment tensor solutions and the aftershock distribution. We constructed spatiotemporal discretized slip-rate functions with patches arranged as closely as possible. We performed inversions using several fault models and found that the spatiotemporal location of large slip-rate area was robust. In the 2016 Kumamoto, Japan earthquake, the slip-rate distribution shows that the rupture propagated to southwest during the first 5 s. At 5 s after the origin time, the main rupture started to propagate toward northeast. First episode and second episode correspond to rupture propagation along the Hinagu fault and the Futagawa fault, respectively. In the 2016 Rieti, Italy earthquake, the slip-rate distribution shows that the rupture propagated to up-dip direction during the first 2 s, and then rupture propagated toward northwest. From both analyses, we propose that the spatiotemporal slip-rate distribution estimated by improved inversion method of tele-seismic body wave has enough information to study a detailed rupture process of M6 7 class earthquake.

Demonstration of Advanced CO₂ Capture Process Improvements for Coal-Fired Flue Gas

Energy Technology Data Exchange (ETDEWEB)

Carroll, John [Southern Company Services, Inc., Wilsonville, AL (United States)

2017-10-01

This document summarizes the activities of Cooperative Agreement DE-FE0026590, “Demonstration of Advanced CO₂ Capture Process Improvements for Coal-Fired Flue Gas” during the performance period of October 1, 2015 through May 31, 2017. This project was funded by the U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL). Southern Company Services, Inc. (SCS) was the prime contractor and co-funder of the project. Mitsubishi Heavy Industries America (MHIA) and AECOM were project team members. The overall project objective was to improve costs, energy requirements, and performance of an existing amine-based CO₂ capture process. This will occur via improvements in three areas: 1. Reboiler design – The first objective of the program was to demonstrate performance of an integrated stripper/reboiler (termed Built-in Reboiler, or BIR) to reduce footprint, capital costs, and integration issues of the current technology. 2. Particulate management – The second objective was to carry out a Particulate Matter Management (PMM) test. This has the potential to reduce operating costs and capital costs due to the reduced or eliminated need for mechanical filtration. 3. Solvent – The third objective was to carry out a new solvent test plan (referred to as NSL) to demonstrate a new solvent (termed New Solvent A), which is expected to reduce regeneration steam. The bulk price is also expected to be lower than KS-1, which is the current solvent used in this process. NSL testing would include baseline testing, optimization, long term testing, solvent reclamation testing, and final inspection. These combine to form the Advanced Carbon Capture (ACC) technology. Much of this work will be applicable to generic solvent processes, especially in regards to improved reboiler design, and focused to meet or exceed the DOE’s overall carbon capture performance goals of 90% CO₂ capture rate with 95% CO₂ purity at a cost of

Improving asthma-related health outcomes among low-income, multiethnic, school-aged children: results of a demonstration project that combined continuous quality improvement and community health worker strategies.

Science.gov (United States)

Fox, Patrick; Porter, Patricia G; Lob, Sibylle H; Boer, Jennifer Holloman; Rocha, David A; Adelson, Joel W

2007-10-01

The purpose of this work was to improve asthma-related health outcomes in an ethnically and geographically disparate population of economically disadvantaged school-aged children by using a team-based approach using continuous quality improvement and community health workers. A demonstration project was conducted with 7 community clinics treating approximately 3000 children with asthma 5 to 18 years of age. The overall clinic population with asthma was assessed for care-process changes through random cross-sectional chart reviews at baseline and 24 months (N = 560). A subset of patients with either moderate or severe persistent asthma or poorly controlled asthma (N = 405) was followed longitudinally for specific asthma-related clinical outcomes, satisfaction with care, and confidence managing asthma by family interview at baseline and at 12 or 24 months. Patient-centered and care-process outcomes included patient/parent assessment of quality of care and confidence in self-management, asthma action plan review, and documentation of guideline-based indicators of quality of care. Direct clinical outcomes included daytime and nighttime symptoms, use of rescue medications, acute care and emergency department visits, hospitalizations, and missed school days. Each clinic site's degree of adherence to the intervention model was evaluated and ranked to examine the correlation between model adherence and outcomes. Cross-sectional data showed clinic-wide improvements in the documentation of asthma severity, review of action plans, health services use, and asthma symptoms. At follow-up in the longitudinal sample, fewer patients reported acute visits, emergency department visits, hospitalizations, frequent daytime and nighttime symptoms, and missed school days compared with baseline. More patients reported excellent or very good quality of care and confidence in asthma self-management. Linear regression analysis of the clinical sites' model adherence ranks against site

Five-year results from a prospective multicentre study of percutaneous pulmonary valve implantation demonstrate sustained removal of significant pulmonary regurgitation, improved right ventricular outflow tract obstruction and improved quality of life

DEFF Research Database (Denmark)

Hager, Alfred; Schubert, Stephan; Ewert, Peter

2017-01-01

. The EQ-5D quality of life utility index and visual analogue scale scores were both significantly improved six months post PPVI and remained so at five years. CONCLUSIONS: Five-year results following PPVI demonstrate resolved moderate or severe pulmonary regurgitation, improved right ventricular outflow...

RM12-2703 Advanced Rooftop Unit Control Retrofit Kit Field Demonstration: Hawaii and Guam Energy Improvement Technology Demonstration Project

Energy Technology Data Exchange (ETDEWEB)

Doebber, I. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Dean, J. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Dominick, J. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Holland, G. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2014-03-01

As part of its overall strategy to meet its energy goals, the Naval Facilities Engineering Command (NAVFAC) partnered with U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) to rapidly demonstrate and deploy cost-effective renewable energy and energy efficiency technologies. This was one of several demonstrations of new and underutilized commercial energy efficiency technologies. The consistent year-round demand for air conditioning and dehumidification in Hawaii provides an advantageous demonstration location for advanced rooftop control (ARC) retrofit kits to packaged rooftop units (RTUs). This report summarizes the field demonstration of ARCs installed on nine RTUs serving a 70,000-ft² exchange store (large retail) and two RTUs, each serving small office buildings located on Joint Base Pearl Harbor-Hickam (JBPHH).

[Lung volume reduction surgery for emphysema and bullous pulmonary emphysema].

Science.gov (United States)

Le Pimpec-Barthes, F; Das Neves-Pereira, J-C; Cazes, A; Arame, A; Grima, R; Hubsch, J-P; Zukerman, C; Hernigou, A; Badia, A; Bagan, P; Delclaux, C; Dusser, D; Riquet, M

2012-04-01

The improvement of respiratory symptoms for emphysematous patients by surgery is a concept that has evolved over time. Initially used for giant bullae, this surgery was then applied to patients with diffuse microbullous emphysema. The physiological and pathological concepts underlying these surgical procedures are the same in both cases: improve respiratory performance by reducing the high intrapleural pressure. The functional benefit of lung volume reduction surgery (LVRS) in the severe diffuse emphysema has been validated by the National Emphysema Treatment Trial (NETT) and the later studies which allowed to identify prognostic factors. The quality of the clinical, morphological and functional data made it possible to develop recommendations now widely used in current practice. Surgery for giant bullae occurring on little or moderately emphysematous lung is often a simpler approach but also requires specialised support to optimize its results. Copyright © 2012 Elsevier Masson SAS. All rights reserved.

Research and demonstration to improve air quality for the U.S. animal feeding operations in the 21st century – A critical review

International Nuclear Information System (INIS)

Ni, Ji-Qin

2015-01-01

There was an increasing interest in reducing production and emission of air pollutants to improve air quality for animal feeding operations (AFOs) in the U.S. in the 21st century. Research was focused on identification, quantification, characterization, and modeling of air pollutions; effects of emissions; and methodologies and technologies for scientific research and pollution control. Mitigation effects were on pre-excretion, pre-release, pre-emission, and post-emission. More emphasis was given on reducing pollutant emissions than improving indoor air quality. Research and demonstrations were generally continuation and improvement of previous efforts. Most demonstrated technologies were still in a limited scale of application. Future efforts are needed in many fundamental and applied research areas. Advancement in instrumentation, computer technology, and biological sciences and genetic engineering is critical to bring major changes in this area. Development in research and demonstration will depend on the actual political, economic, and environmental situations. - Highlights: • More emphasis was placed on pollutant emissions than indoor air quality. • Basic research dedicated to new pollutants, modeling, and baseline emissions. • Applied research focused on developing monitoring and mitigation technologies. • Field demonstrations combined with projects to evaluate new mitigation approaches. • Future efforts are needed in many fundamental and applied research areas. - Different scales of basic and applied research were conducted and 15 mitigation technologies were demonstrated. Future work is needed in many fundamental and applied research areas

Virtual Lab Demonstrations Improve Students’ Mastery of Basic Biology Laboratory Techniques

OpenAIRE

Maldarelli, Grace A.; Hartmann, Erica M.; Cummings, Patrick J.; Horner, Robert D.; Obom, Kristina. M.; Shingles, Richard; Pearlman, Rebecca S.

2009-01-01

Biology laboratory classes are designed to teach concepts and techniques through experiential learning. Students who have never performed a technique must be guided through the process, which is often difficult to standardize across multiple lab sections. Visual demonstration of laboratory procedures is a key element in teaching pedagogy. The main goals of the study were to create videos explaining and demonstrating a variety of lab techniques that would serve as teaching tools for undergradu...

Use of subvoxel registration and subtraction to improve demonstration of contrast enhancement in MRI of the brain

International Nuclear Information System (INIS)

Curati, W.L.; Williams, E.J.; Oatridge, A.; Hajnal, J.V.; Saeed, N.; Bydder, G.M.

1996-01-01

To assess the potential of registration of images before and after contrast medium for improving the demonstration of contrast enhancement, we compared conventional 2 D T 1-weighted spin-echo images with precisely registered 3 D volume images and subtraction images derived from them in 2 normal subjects and 30 patients with a variety of brain disease. The volume images were registered to subvoxel accuracy using a rigid body translation and rotation, sinc interpolation and a least-squares fit; subtraction images were obtained from these. Normal contrast enhancement was demonstrated better with positionally registered volume and subtraction images than with conventional images in the meninges, ependyma, diploic veins, scalp, skin, orbit and sinuses. Abnormal enhancement was seen better in meningeal disease, multiple sclerosis and tumours as well as on follow-up studies. Subvoxel registration of images before and after contrast medium may be of considerable value in the recognition of contrast enhancement where there are small changes, or where the changes affect tissues with high or low baseline signal values. The technique also appears likely to be of value in demonstrating contrast enhancement in tissues at inferfaces and at other areas of complex anatomy, and in follow-up studies. (orig.). With 4 figs., 4 tabs

High-fidelity hybrid simulation of allergic emergencies demonstrates improved preparedness for office emergencies in pediatric allergy clinics.

Science.gov (United States)

Kennedy, Joshua L; Jones, Stacie M; Porter, Nicholas; White, Marjorie L; Gephardt, Grace; Hill, Travis; Cantrell, Mary; Nick, Todd G; Melguizo, Maria; Smith, Chris; Boateng, Beatrice A; Perry, Tamara T; Scurlock, Amy M; Thompson, Tonya M

2013-01-01

Simulation models that used high-fidelity mannequins have shown promise in medical education, particularly for cases in which the event is uncommon. Allergy physicians encounter emergencies in their offices, and these can be the source of much trepidation. To determine if case-based simulations with high-fidelity mannequins are effective in teaching and retention of emergency management team skills. Allergy clinics were invited to Arkansas Children's Hospital Pediatric Understanding and Learning through Simulation Education center for a 1-day workshop to evaluate skills concerning the management of allergic emergencies. A Clinical Emergency Preparedness Team Performance Evaluation was developed to evaluate the competence of teams in several areas: leadership and/or role clarity, closed-loop communication, team support, situational awareness, and scenario-specific skills. Four cases, which focus on common allergic emergencies, were simulated by using high-fidelity mannequins and standardized patients. Teams were evaluated by multiple reviewers by using video recording and standardized scoring. Ten to 12 months after initial training, an unannounced in situ case was performed to determine retention of the skills training. Clinics showed significant improvements for role clarity, teamwork, situational awareness, and scenario-specific skills during the 1-day workshop (all P clinics (all P ≤ .004). Clinical Emergency Preparedness Team Performance Evaluation scores demonstrated improved team management skills with simulation training in office emergencies. Significant recall of team emergency management skills was demonstrated months after the initial training. Copyright © 2013 American Academy of Allergy, Asthma & Immunology. Published by Elsevier Inc. All rights reserved.

Virtual Lab Demonstrations Improve Students’ Mastery of Basic Biology Laboratory Techniques

Directory of Open Access Journals (Sweden)

Grace A. Maldarelli

2009-12-01

Full Text Available Biology laboratory classes are designed to teach concepts and techniques through experiential learning. Students who have never performed a technique must be guided through the process, which is often difficult to standardize across multiple lab sections. Visual demonstration of laboratory procedures is a key element in teaching pedagogy. The main goals of the study were to create videos explaining and demonstrating a variety of lab techniques that would serve as teaching tools for undergraduate and graduate lab courses and to assess the impact of these videos on student learning. Demonstrations of individual laboratory procedures were videotaped and then edited with iMovie. Narration for the videos was edited with Audacity. Undergraduate students were surveyed anonymously prior to and following screening to assess the impact of the videos on student lab performance by completion of two Participant Perception Indicator surveys. A total of 203 and 171 students completed the pre- and posttesting surveys, respectively. Statistical analyses were performed to compare student perceptions of knowledge of, confidence in, and experience with the lab techniques before and after viewing the videos. Eleven demonstrations were recorded. Chi-square analysis revealed a significant increase in the number of students reporting increased knowledge of, confidence in, and experience with the lab techniques after viewing the videos. Incorporation of instructional videos as prelaboratory exercises has the potential to standardize techniques and to promote successful experimental outcomes.

Modelled female sale options demonstrate improved profitability in northern beef herds.

Science.gov (United States)

Niethe, G E; Holmes, W E

2008-12-01

To examine the impact of improving the average value of cows sold, the risk of decreasing the number weaned, and total sales on the profitability of northern Australian cattle breeding properties. Gather, model and interpret breeder herd performances and production parameters on properties from six beef-producing regions in northern Australia. Production parameters, prices, costs and herd structure were entered into a herd simulation model for six northern Australian breeding properties that spay females to enhance their marketing options. After the data were validated by management, alternative management strategies were modelled using current market prices and most likely herd outcomes. The model predicted a close relationship between the average sale value of cows, the total herd sales and the gross margin/adult equivalent. Keeping breeders out of the herd to fatten generally improves their sale value, and this can be cost-effective, despite the lower number of progeny produced and the subsequent reduction in total herd sales. Furthermore, if the price of culled cows exceeds the price of culled heifers, provided there are sufficient replacement pregnant heifers available to maintain the breeder herd nucleus, substantial gains in profitability can be obtained by decreasing the age at which cows are culled from the herd. Generalised recommendations on improving reproductive performance are not necessarily the most cost-effective strategy to improve breeder herd profitability. Judicious use of simulation models is essential to help develop the best turnoff strategies for females and to improve station profitability.

IMPROVING LEARNING PROCESS AND STUDENT RESULTS LEARNING TO TUNE-UPMOTORCYCLE USING DEMONSTRATION METHODOF CLASS XI SMA N 1 PLAYEN YEAR STUDY2013/2014

Directory of Open Access Journals (Sweden)

Haryono Haryono

2014-12-01

Full Text Available This research is to improve the learning process and results in learning a tune-up motorcycle  using the demonstrationmethod of class XI SMA 1 Playen.              This research is a classroom action research (PTK, using the demonstration method.Subyek this study were students of class XI SMA Negeri 1 Playen.Theimplementationofthisstudyusing3cycles,there is a (planning, implementation (actuating, observation (observing, and reflection (reflecting. Collecting data in this study are observations of student learning process and student learning outcomes test data pre-test, postesI, II, III and documentation as a support to the two data. Further observation data based on the observation of student learning just learning the positive process of learning student and test data were analyzed for comparison. Indicators of success in this classroom action research that student learning increases towards positive along with the use of methods of demonstration, is to see an increase from the pre-cycle to end the first cycle, the first cycle to the second cycle and the secondcyclebycycle III.             From the results of this study concluded that the method could improve the demonstration of positive student learning, from the first cycle of 30%, 50% second cycle and third cycle of 80%. Learning is also more effective with students indicated more quickly adapt as a positive activity, especially in terms of increased student asked, noting the test and work on the problems. Demonstration method can improve the learning outcomes  students of class XI SMA 1 Playen as evidenced by an increase in the average yield final test first cycle of 64.09; second cycle of 77.82 and 78.86 for the third cycle. So it proved with the increasing positive student learning canalso improve student learning outcomes.

Challenging demonstrations in the physics classroom

International Nuclear Information System (INIS)

Raz, E.

2004-01-01

Full Text: We consider the role of classroom demonstrations in improving students understanding of physics lectures and suggest criteria to decide whether a given demonstration will be pedagogically useful. In the light of these considerations, we performed two series of related experiments before groups of high-school students. We shall perform one of them with active participation from the audience. We shall also show some challenging demonstrations performed in the final stages of the Israeli Physics Olympiad for high-school students

Waste-to-Energy: Hawaii and Guam Energy Improvement Technology Demonstration Project

Energy Technology Data Exchange (ETDEWEB)

Davis, J. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Gelman, R. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Tomberlin, G. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Bain, R. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2014-03-01

The National Renewable Energy Laboratory (NREL) and the U.S. Navy have worked together to demonstrate new or leading-edge commercial energy technologies whose deployment will support the U.S. Department of Defense (DOD) in meeting its energy efficiency and renewable energy goals while enhancing installation energy security. This is consistent with the 2010 Quadrennial Defense Review report1 that encourages the use of 'military installations as a test bed to demonstrate and create a market for innovative energy efficiency and renewable energy technologies coming out of the private sector and DOD and Department of Energy laboratories,' as well as the July 2010 memorandum of understanding between DOD and the U.S. Department of Energy (DOE) that documents the intent to 'maximize DOD access to DOE technical expertise and assistance through cooperation in the deployment and pilot testing of emerging energy technologies.' As part of this joint initiative, a promising waste-to-energy (WTE) technology was selected for demonstration at the Hickam Commissary aboard the Joint Base Pearl Harbor-Hickam (JBPHH), Hawaii. The WTE technology chosen is called high-energy densification waste-to-energy conversion (HEDWEC). HEDWEC technology is the result of significant U.S. Army investment in the development of WTE technology for forward operating bases.

Lung volume reduction surgery: an overview Cirurgia redutora de volume pulmonar: uma revisão

Directory of Open Access Journals (Sweden)

Rodrigo Afonso da Silva Sardenberg

2010-01-01

Full Text Available This study intends to review the literature on the efficacy, safety and feasibility of lung volume reduction surgery (LVRS in patients with advanced emphysema. Studies on LVRS from January 1995 to December 2009 were included by using Pubmed (MEDLINE and Cochrane Library literature in English. Search words such as lung volume reduction surgery or lung reduction surgery, pneumoplasty or reduction pneumoplasty, COPD or chronic obstructive pulmonary disease and surgery, were used. We also compared medical therapy and surgical technique. Studies consisting of randomized controlled trials, controlled clinical trials (randomized and nonrandomized, reviews and case series were analyzed. Questions regarding validity of the early clinical reports, incomplete follow-up bias, selection criteria and survival, confounded the interpretation of clinical data on LVRS. Patients with upper, lower and diffuse distribution of emphysema were included; we also analyzed as key points perioperative morbidity and mortality and lung function measurement as FEV1. Bullous emphysema was excluded from this review. Surgical approach included median sternotomy, unilateral or bilateral thoracotomy, and videothoracoscopy with stapled or laser ablation. Results of prospective randomized trials between medical management and LVRS are essential before final assessment can be established.O objetivo deste estudo é revisar a literatura acerca da eficácia, segurança e viabilidade da cirurgia redutora de volume pulmonar (CRVP em pacientes com enfisema pulmonar avançado. Estudos de CRVP de janeiro de 1995 a dezembro de 2009 foram incluídos através de pesquisa na Pubmed (MEDLINE e Cochrane Library, na literatura inglesa. Palavras de busca tais como lung volume reduction surgery ou lung reduction surgery, pneumoplasty ou reduction pneumoplasty, COPD ou chronic obstructive pulmonary disease e surgery foram utilizadas. Também realizamos comparação entre terapia médica e cir

Demonstration of innovative monitoring technologies at the Savannah River Integrated Demonstration Site

Energy Technology Data Exchange (ETDEWEB)

Rossabi, J. [Westinghouse Savannah River Co., Aiken, SC (United States); Jenkins, R.A.; Wise, M.B. [Oak Ridge National Lab., TN (United States)] [and others

1993-12-31

The Department of Energy`s Office of Technology Development initiated an Integrated Demonstration Program at the Savannah River Site in 1989. The objective of this program is to develop, demonstrate, and evaluate innovative technologies that can improve present-day environmental restoration methods. The Integrated Demonstration Program at SRS is entitled ``Cleanup of Organics in Soils and Groundwater at Non-Arid Sites.`` New technologies in the areas of drilling, characterization, monitoring, and remediation are being demonstrated and evaluated for their technical performance and cost effectiveness in comparison with baseline technologies. Present site characterization and monitoring methods are costly, time-consuming, overly invasive, and often imprecise. Better technologies are required to accurately describe the subsurface geophysical and geochemical features of a site and the nature and extent of contamination. More efficient, nonintrusive characterization and monitoring techniques are necessary for understanding and predicting subsurface transport. More reliable procedures are also needed for interpreting monitoring and characterization data. Site characterization and monitoring are key elements in preventing, identifying, and restoring contaminated sites. The remediation of a site cannot be determined without characterization data, and monitoring may be required for 30 years after site closure.

Demonstration of innovative monitoring technologies at the Savannah River Integrated Demonstration Site

International Nuclear Information System (INIS)

Rossabi, J.; Jenkins, R.A.; Wise, M.B.

1993-01-01

The Department of Energy's Office of Technology Development initiated an Integrated Demonstration Program at the Savannah River Site in 1989. The objective of this program is to develop, demonstrate, and evaluate innovative technologies that can improve present-day environmental restoration methods. The Integrated Demonstration Program at SRS is entitled ''Cleanup of Organics in Soils and Groundwater at Non-Arid Sites.'' New technologies in the areas of drilling, characterization, monitoring, and remediation are being demonstrated and evaluated for their technical performance and cost effectiveness in comparison with baseline technologies. Present site characterization and monitoring methods are costly, time-consuming, overly invasive, and often imprecise. Better technologies are required to accurately describe the subsurface geophysical and geochemical features of a site and the nature and extent of contamination. More efficient, nonintrusive characterization and monitoring techniques are necessary for understanding and predicting subsurface transport. More reliable procedures are also needed for interpreting monitoring and characterization data. Site characterization and monitoring are key elements in preventing, identifying, and restoring contaminated sites. The remediation of a site cannot be determined without characterization data, and monitoring may be required for 30 years after site closure

Evaluation and demonstration of methods for improved fuel utilization. First semi-annual progress report, September 1979-March 1980

International Nuclear Information System (INIS)

Decher, U.

1980-01-01

Demonstrations of improved fuel management and burnup are being performed in the Fort Calhoun reactor. More efficient fuel management will be achieved through the implementation of a low leakage concept called SAVFUEL (Shimmed And Very Flexible Uranium Element Loading), which is expected to reduce uranium requirements by 2 to 4%. The burnup will be increased sufficiently to reduce uranium requirements by 5 to 15%. Four fuel assemblies scheduled to demonstrate the SAVFUEL duty cycle and loaded into the core in December 1978 were inspected visually prior to their second exposure cycle. In addition, seventeen fuel assemblies were inspected after their fourth exposure cycle having achieved assembly average burnup up to 36 GWD/T. One assembly has been reinserted into Cycle 6 for a fifth exposure cycle. The preliminary results of all visual fuel inspections which appear to show excellent fuel rod performance are presented in this report. This report also contains the results of a licensing activity which was performed to allow insertion of a highly burned assembly into the reactor for a fifth irradiation cycle

Periowave demonstrates bactericidal activity against periopathogens and leads to improved clinical outcomes in the treatment of adult periodontitis

Science.gov (United States)

Street, Cale N.; Andersen, Roger; Loebel, Nicolas G.

2009-02-01

Periodontitis affects half of the U.S. population over 50, and is the leading cause of tooth loss after 35. It is believed to be caused by growth of complex bacterial biofilms on the tooth surface below the gumline. Photodynamic therapy, a technology used commonly in antitumor applications, has more recently been shown to exhibit antimicrobial efficacy. We have demonstrated eradication of the periopathogens Porphyromonas gingivalis, Fusobacterium nucleatum, and Aggregatibacter actinomycetemcomitans in vitro using PeriowaveTM; a commercial photodisinfection system. In addition, several clinical studies have now demonstrated the efficacy of this treatment. A pilot study in the U.S. showed that 68% of patients treated with PeriowaveTM adjunctively to scaling and root planing (SRP) showed clinical attachment level increase of >1 mm, as opposed to 30% with SRP alone. In a subsequent larger study, a second PeriowaveTM treatment 6 weeks after initial treatment led to pocket depth improvements of >1.5 mm in 89% of patients. Finally, in the most recent multicenter, randomized, examiner-blinded study conducted on 121 subjects in Canada, PeriowaveTM treatment produced highly significant gains in attachment level (0.88 mm vs. 0.57 mm; p=0.003) and pocket depth (0.87 mm vs. 0.63 mm; p=0.01) as compared to SRP alone. In summary, PeriowaveTM demonstrated strong bactericidal activity against known periopathogens, and treatment of periodontitis using this system produced significantly better clinical outcomes than SRP alone. This, along with the absence of any adverse events in patients treated to date demonstrates that PDT is a safe and effective treatment for adult chronic periodontitis.

Hybrid Life Support System Technology Demonstrations

Science.gov (United States)

Morrow, R. C.; Wetzel, J. P.; Richter, R. C.

2018-02-01

Demonstration of plant-based hybrid life support technologies in deep space will validate the function of these technologies for long duration missions, such as Mars transit, while providing dietary variety to improve habitability.

Waste and Disposal: Demonstration

International Nuclear Information System (INIS)

Neerdael, B.; Buyens, M.; De Bruyn, D.; Volckaert, G.

2002-01-01

Within the Belgian R and D programme on geological disposal, demonstration experiments have become increasingly important. In this contribution to the scientific report 2001, an overview is given of SCK-CEN's activities and achievements in the field of large-scale demonstration experiments. In 2001, main emphasis was on the PRACLAY project, which is a large-scale experiment to demonstrate the construction and the operation of a gallery for the disposal of HLW in a clay formation. The PRACLAY experiment will contribute to enhance understanding of water flow and mass transport in dense clay-based materials as well as to improve the design of the reference disposal concept. In the context of PRACLAY, a surface experiment (OPHELIE) has been developed to prepare and to complement PRACLAY-related experimental work in the HADES Underground Research Laboratory. In 2001, efforts were focussed on the operation of the OPHELIE mock-up. SCK-CEN also contributed to the SELFRAC roject which studies the self-healing of fractures in a clay formation

A demonstration of the improved efficiency of the canonical coordinates method using nonlinear combined heat and power economic dispatch problems

Science.gov (United States)

Chang, Hung-Chieh; Lin, Pei-Chun

2014-02-01

Economic dispatch is the short-term determination of the optimal output from a number of electricity generation facilities to meet the system load while providing power. As such, it represents one of the main optimization problems in the operation of electrical power systems. This article presents techniques to substantially improve the efficiency of the canonical coordinates method (CCM) algorithm when applied to nonlinear combined heat and power economic dispatch (CHPED) problems. The improvement is to eliminate the need to solve a system of nonlinear differential equations, which appears in the line search process in the CCM algorithm. The modified algorithm was tested and the analytical solution was verified using nonlinear CHPED optimization problems, thereby demonstrating the effectiveness of the algorithm. The CCM methods proved numerically stable and, in the case of nonlinear programs, produced solutions with unprecedented accuracy within a reasonable time.

Reducing Plug Loads in Office Spaces: Hawaii and Guam Energy Improvement Technology Demonstration Project

Energy Technology Data Exchange (ETDEWEB)

Sheppy, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Metzger, I. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Cutler, D. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Holland, G. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Hanada, A. [Naval Facilities Engineering Command, Washington, DC (United States)

2014-01-01

As part of its overall strategy to meet its energy goals, the Naval Facilities Engineering Command (NAVFAC) partnered with the Department of Energy's National Renewable Energy Laboratory (NREL) to rapidly demonstrate and deploy cost-effective renewable energy and energy efficiency technologies. This project was one of several demonstrations of new or underutilized commercial energy technologies. The common goal was to demonstrate and measure the performance and economic benefit of the system while monitoring any ancillary impacts to related standards of service and operation and maintenance (O&M) practices. In short, demonstrations at naval facilities simultaneously evaluate the benefits and compatibility of the technology with the U.S. Department of Defense (DOD) mission, and with NAVFAC's design, construction, operations, and maintenance practices, in particular. This project demonstrated the performance of commercially available advanced power strips (APSs) for plug load energy reductions in building A4 at Joint Base Pearl Harbor-Hickam (JBPHH), Hawaii.

First demonstration of improving laser propagation inside the spherical hohlraums by using the cylindrical laser entrance hole

Directory of Open Access Journals (Sweden)

Wenyi Huo

2016-01-01

Full Text Available The octahedral spherical hohlraums have natural superiority in maintaining high radiation symmetry during the entire capsule implosion process in indirect drive inertial confinement fusion. While, in contrast to the cylindrical hohlraums, the narrow space between the laser beams and the spherical hohlraum wall is usually commented. In this Letter, we address this crucial issue and report our experimental work conducted on the SGIII-prototype laser facility which unambiguously demonstrates that a simple design of cylindrical laser entrance hole (LEH can dramatically improve the laser propagation inside the spherical hohlraums. In addition, the laser beam deflection in the hohlraum is observed for the first time in the experiments. Our 2-dimensional simulation results also verify qualitatively the advantages of the spherical hohlraums with cylindrical LEHs. Our results imply the prospect of adopting the cylindrical LEHs in future spherical ignition hohlraum design.

Smart Grid Demonstration Project

Energy Technology Data Exchange (ETDEWEB)

Miller, Craig [National Rural Electric Cooperative Association, Arlington, VA (United States); Carroll, Paul [National Rural Electric Cooperative Association, Arlington, VA (United States); Bell, Abigail [National Rural Electric Cooperative Association, Arlington, VA (United States)

2015-03-11

The National Rural Electric Cooperative Association (NRECA) organized the NRECA-U.S. Department of Energy (DOE) Smart Grid Demonstration Project (DE-OE0000222) to install and study a broad range of advanced smart grid technologies in a demonstration that spanned 23 electric cooperatives in 12 states. More than 205,444 pieces of electronic equipment and more than 100,000 minor items (bracket, labels, mounting hardware, fiber optic cable, etc.) were installed to upgrade and enhance the efficiency, reliability, and resiliency of the power networks at the participating co-ops. The objective of this project was to build a path for other electric utilities, and particularly electrical cooperatives, to adopt emerging smart grid technology when it can improve utility operations, thus advancing the co-ops’ familiarity and comfort with such technology. Specifically, the project executed multiple subprojects employing a range of emerging smart grid technologies to test their cost-effectiveness and, where the technology demonstrated value, provided case studies that will enable other electric utilities—particularly electric cooperatives— to use these technologies. NRECA structured the project according to the following three areas: Demonstration of smart grid technology; Advancement of standards to enable the interoperability of components; and Improvement of grid cyber security. We termed these three areas Technology Deployment Study, Interoperability, and Cyber Security. Although the deployment of technology and studying the demonstration projects at coops accounted for the largest portion of the project budget by far, we see our accomplishments in each of the areas as critical to advancing the smart grid. All project deliverables have been published. Technology Deployment Study: The deliverable was a set of 11 single-topic technical reports in areas related to the listed technologies. Each of these reports has already been submitted to DOE, distributed to co-ops, and

Improving Perinatal Care in the Rural Regions Worldwide by Wireless Enabled Antepartum Fetal Monitoring: A Demonstration Project

Directory of Open Access Journals (Sweden)

Roberto Tapia-Conyer

2015-01-01

Full Text Available Background. Fetal and neonatal morbidity and mortality are significant problems in developing countries; remote maternal-fetal monitoring offers promise in addressing this challenge. The Gary and Mary West Health Institute and the Instituto Carlos Slim de la Salud conducted a demonstration project of wirelessly enabled antepartum maternal-fetal monitoring in the state of Yucatán, Mexico, to assess whether there were any fundamental barriers preventing deployment and use. Methods. Following informed consent, high-risk pregnant women at 27–29 weeks of gestation at the Chemax primary clinic participated in remote maternal-fetal monitoring. Study participants were randomized to receive either prototype wireless monitoring or standard-of-care. Feasibility was evaluated by assessing technical aspects of performance, adherence to monitoring appointments, and response to recommendations. Results. Data were collected from 153 high-risk pregnant indigenous Mayan women receiving either remote monitoring (n=74 or usual standard-of-care (n=79. Remote monitoring resulted in markedly increased adherence (94.3% versus 45.1%. Health outcomes were not statistically different in the two groups. Conclusions. Remote maternal-fetal monitoring is feasible in resource-constrained environments and can improve maternal compliance for monitoring sessions. Improvement in maternal-fetal health outcomes requires integration of such technology into sociocultural context and addressing logistical challenges of access to appropriate emergency services.

Improving Perinatal Care in the Rural Regions Worldwide by Wireless Enabled Antepartum Fetal Monitoring: A Demonstration Project

Science.gov (United States)

Tapia-Conyer, Roberto; Lyford, Shelley; Saucedo, Rodrigo; Casale, Michael; Gallardo, Hector; Becerra, Karen; Mack, Jonathan; Mujica, Ricardo; Estrada, Daniel; Sanchez, Antonio; Sabido, Ramon; Meier, Carlos; Smith, Joseph

2015-01-01

Background. Fetal and neonatal morbidity and mortality are significant problems in developing countries; remote maternal-fetal monitoring offers promise in addressing this challenge. The Gary and Mary West Health Institute and the Instituto Carlos Slim de la Salud conducted a demonstration project of wirelessly enabled antepartum maternal-fetal monitoring in the state of Yucatán, Mexico, to assess whether there were any fundamental barriers preventing deployment and use. Methods. Following informed consent, high-risk pregnant women at 27–29 weeks of gestation at the Chemax primary clinic participated in remote maternal-fetal monitoring. Study participants were randomized to receive either prototype wireless monitoring or standard-of-care. Feasibility was evaluated by assessing technical aspects of performance, adherence to monitoring appointments, and response to recommendations. Results. Data were collected from 153 high-risk pregnant indigenous Mayan women receiving either remote monitoring (n = 74) or usual standard-of-care (n = 79). Remote monitoring resulted in markedly increased adherence (94.3% versus 45.1%). Health outcomes were not statistically different in the two groups. Conclusions. Remote maternal-fetal monitoring is feasible in resource-constrained environments and can improve maternal compliance for monitoring sessions. Improvement in maternal-fetal health outcomes requires integration of such technology into sociocultural context and addressing logistical challenges of access to appropriate emergency services. PMID:25691900

Transit Marketing : A Program of Research, Demonstration and Communication

Science.gov (United States)

1985-04-01

This report recommends a five-year program of research, demonstration, and communication to improve the effectiveness of marketing practice in the U.S. transit industry. The program is oriented toward the development of improved market research tools...

ARSENIC REMOVAL FROM DRINKING WATER BY ADSORPTIVE MEDIA. U.S. EPA DEMONSTRATION PROJECT AT SOUTH TRUCKEE MEADOWS GENERAL IMPROVEMENT DISTRICT (STMIG), NV. INTERIM EVALUATION REPORT

Science.gov (United States)

This report documents the activities performed during and the results obtained from the first 32 weeks of operation of an arsenic and antimony removal technology currently being demonstrated at the South Truckee Meadows General Improvement District (STMGID) in Washoe County, NV. ...

Evaluating a Program Designed to Demonstrate Continuous Improvement in Teaching at an AACSB-Accredited College of Business at a Regional University: A Case Study

Science.gov (United States)

Pritchard, Robert E.; Saccucci, Michael S.; Potter, Gregory C.

2010-01-01

This article provides a detailed statistical analysis of a process intended to demonstrate continuous improvement in teaching at an AACSB accredited college of business. The Educational Testing Service's SIR II student evaluation instrument was used to measure teaching effectiveness. A six-year longitudinal analysis of the SIR II results does not…

Clean Coal Technology Demonstration Program: Program Update 2001

Energy Technology Data Exchange (ETDEWEB)

Assistant Secretary for Fossil Energy

2002-07-30

Annual report on the Clean Coal Technology Demonstration Program (CCT Program). The report address the role of the CCT Program, implementation, funding and costs, accomplishments, project descriptions, legislative history, program history, environmental aspects, and project contacts. The project descriptions describe the technology and provides a brief summary of the demonstration results. Also includes Power Plant Improvement Initiative Projects.

Plasma hearth process demonstration project

International Nuclear Information System (INIS)

Geimer, R.M.; Gillins, R.L.

1995-01-01

The Plasma Hearth Process (PHP) demonstration project is one of the key technology projects in the US Department of Energy (DOE) Office of Technology Development Mixed Waste Focus Area. The PHP is a high temperature thermal treatment process using a plasma arc torch in a stationary, refractory lined chamber that destroys organics and stabilizes the residuals in a nonleaching, vitrified waste form, greatly improving the disposability of the waste. This paper describes the PHP system and summarizes test results to date, including volume reduction, destruction and removal efficiencies for organic wastes, and emission characteristics. Tests performed so far demonstrate that the PHP adresses DOE mixed waste final waste form requirements and US Environmental Protection Agency Toxicity Characteristic Leaching Procedure requirements

Functional improvement after carotid endarterectomy: demonstrated by gait analysis and acetazolamide stress brain perfusion SPECT

International Nuclear Information System (INIS)

Kim, J. S.; Kim, G. E.; Yoo, J. Y.; Kim, D. G.; Moon, D. H.

2005-01-01

Scientific documentation of neurologic improvement following carotid endarterectomy (CEA) has not been established. The purpose of this prospective study is to investigate whether CEA performed for the internal carotid artery flow lesion improves gait and cerebrovascular hemodynamic status in patients with gait disturbance. We prospectively performed pre- and postCEA gait analysis and acetazolamide stress brain perfusion SPECT (Acz-SPECT) with Tc-99m ECD in 91 patients (M/F: 81/10, mean age: 64.1 y) who had gait disturbance before receiving CEA. Gait performance was assessed using a Vicon 370 motion analyzer. The gait improvement after CEA was correlated to cerebrovascular hemodynamic change as well as symptom duration. 12 hemiparetic stroke patients (M/F=9/3, mean age: 51 y) who did not receive CEA as a control underwent gait analysis twice in a week interval to evaluate whether repeat testing of gait performance shows learning effect. Of 91 patients, 73 (80%) patients showed gait improvement (change of gait speed > 10%) and 42 (46%) showed marked improvement (change of gait speed > 20%), but no improvement was observed in control group at repeat test. Post-operative cerebrovascular hemodynamic improvement was noted in 49 (54%) of 91 patients. There was marked gait improvement in patients group with cerebrovascular hemodynamic improvement compared to no change group (p<0.05). Marked gait improvement and cerebrovascular hemodynamic improvement were noted in 53% and 61% of the patient who had less than 3 month history of symptom compared to 31% and 24% of the patients who had longer than 3 months, respectively (p<0.05). Marked gait improvement was obtained in patients who had improvement of cerebrovascular hemodynamic status on Acz-SPECT after CEA. These results suggest functional improvement such as gait can result from the improved perfusion of misery perfusion area, which is viable for a longer period compared to literatures previously reported

Demonstration of reliability centered maintenance

International Nuclear Information System (INIS)

Schwan, C.A.; Morgan, T.A.

1991-04-01

Reliability centered maintenance (RCM) is an approach to preventive maintenance planning and evaluation that has been used successfully by other industries, most notably the airlines and military. Now EPRI is demonstrating RCM in the commercial nuclear power industry. Just completed are large-scale, two-year demonstrations at Rochester Gas ampersand Electric (Ginna Nuclear Power Station) and Southern California Edison (San Onofre Nuclear Generating Station). Both demonstrations were begun in the spring of 1988. At each plant, RCM was performed on 12 to 21 major systems. Both demonstrations determined that RCM is an appropriate means to optimize a PM program and improve nuclear plant preventive maintenance on a large scale. Such favorable results had been suggested by three earlier EPRI pilot studies at Florida Power ampersand Light, Duke Power, and Southern California Edison. EPRI selected the Ginna and San Onofre sites because, together, they represent a broad range of utility and plant size, plant organization, plant age, and histories of availability and reliability. Significant steps in each demonstration included: selecting and prioritizing plant systems for RCM evaluation; performing the RCM evaluation steps on selected systems; evaluating the RCM recommendations by a multi-disciplinary task force; implementing the RCM recommendations; establishing a system to track and verify the RCM benefits; and establishing procedures to update the RCM bases and recommendations with time (a living program). 7 refs., 1 tab

Demonstration of Passive Fuel Cell Thermal Management Technology

Science.gov (United States)

Burke, Kenneth A.; Jakupca, Ian; Colozza, Anthony; Wynne, Robert; Miller, Michael; Meyer, Al; Smith, William

2012-01-01

The NASA Glenn Research Center is developing advanced passive thermal management technology to reduce the mass and improve the reliability of space fuel cell systems for the NASA Exploration program. The passive thermal management system relies on heat conduction within highly thermally conductive cooling plates to move the heat from the central portion of the cell stack out to the edges of the fuel cell stack. Using the passive approach eliminates the need for a coolant pump and other cooling loop components within the fuel cell system which reduces mass and improves overall system reliability. Previous development demonstrated the performance of suitable highly thermally conductive cooling plates and integrated heat exchanger technology to collect the heat from the cooling plates (Ref. 1). The next step in the development of this passive thermal approach was the demonstration of the control of the heat removal process and the demonstration of the passive thermal control technology in actual fuel cell stacks. Tests were run with a simulated fuel cell stack passive thermal management system outfitted with passive cooling plates, an integrated heat exchanger and two types of cooling flow control valves. The tests were run to demonstrate the controllability of the passive thermal control approach. Finally, successful demonstrations of passive thermal control technology were conducted with fuel cell stacks from two fuel cell stack vendors.

Continuing Robot Skill Learning after Demonstration with Human Feedback

Directory of Open Access Journals (Sweden)

Argall Brenna D.

2011-12-01

Full Text Available Though demonstration-based approaches have been successfully applied to learning a variety of robot behaviors, there do exist some limitations. The ability to continue learning after demonstration, based on execution experience with the learned policy, therefore has proven to be an asset to many demonstration-based learning systems. This paper discusses important considerations for interfaces that provide feedback to adapt and improve demonstrated behaviors. Feedback interfaces developed for two robots with very different motion capabilities - a wheeled mobile robot and high degree-of-freedom humanoid - are highlighted.

Fuel Cell Demonstration Program

Energy Technology Data Exchange (ETDEWEB)

Gerald Brun

2006-09-15

In an effort to promote clean energy projects and aid in the commercialization of new fuel cell technologies the Long Island Power Authority (LIPA) initiated a Fuel Cell Demonstration Program in 1999 with six month deployments of Proton Exchange Membrane (PEM) non-commercial Beta model systems at partnering sites throughout Long Island. These projects facilitated significant developments in the technology, providing operating experience that allowed the manufacturer to produce fuel cells that were half the size of the Beta units and suitable for outdoor installations. In 2001, LIPA embarked on a large-scale effort to identify and develop measures that could improve the reliability and performance of future fuel cell technologies for electric utility applications and the concept to establish a fuel cell farm (Farm) of 75 units was developed. By the end of October of 2001, 75 Lorax 2.0 fuel cells had been installed at the West Babylon substation on Long Island, making it the first fuel cell demonstration of its kind and size anywhere in the world at the time. Designed to help LIPA study the feasibility of using fuel cells to operate in parallel with LIPA's electric grid system, the Farm operated 120 fuel cells over its lifetime of over 3 years including 3 generations of Plug Power fuel cells (Lorax 2.0, Lorax 3.0, Lorax 4.5). Of these 120 fuel cells, 20 Lorax 3.0 units operated under this Award from June 2002 to September 2004. In parallel with the operation of the Farm, LIPA recruited government and commercial/industrial customers to demonstrate fuel cells as on-site distributed generation. From December 2002 to February 2005, 17 fuel cells were tested and monitored at various customer sites throughout Long Island. The 37 fuel cells operated under this Award produced a total of 712,635 kWh. As fuel cell technology became more mature, performance improvements included a 1% increase in system efficiency. Including equipment, design, fuel, maintenance

Demonstration of improved vehicle fuel efficiency through innovative tire design, materials, and weight reduction technologies

Energy Technology Data Exchange (ETDEWEB)

Donley, Tim [Cooper Tire & Rubber Company Incorporated, Findlay, OH (United States)

2014-12-31

Cooper completed an investigation into new tire technology using a novel approach to develop and demonstrate a new class of fuel efficient tires using innovative materials technology and tire design concepts. The objective of this work was to develop a new class of fuel efficient tires, focused on the “replacement market” that would improve overall passenger vehicle fuel efficiency by 3% while lowering the overall tire weight by 20%. A further goal of this project was to accomplish the objectives while maintaining the traction and wear performance of the control tire. This program was designed to build on what has already been accomplished in the tire industry for rolling resistance based on the knowledge and general principles developed over the past decades. Cooper’s CS4 (Figure #1) premium broadline tire was chosen as the control tire for this program. For Cooper to achieve the goals of this project, the development of multiple technologies was necessary. Six technologies were chosen that are not currently being used in the tire industry at any significant level, but that showed excellent prospects in preliminary research. This development was divided into two phases. Phase I investigated six different technologies as individual components. Phase II then took a holistic approach by combining all the technologies that showed positive results during phase one development.

FINDING SOLUTIONS AT THE WEST VALLEY DEMONSTRATION PROJECT

International Nuclear Information System (INIS)

Drake, John L.; Gramling, James M.; Houston, Helene M.

2003-01-01

The United States Department of Energy Office of Environmental Management (DOE-EM) faces a number of sizeable challenges as it begins to transform its mission from managing risk to reducing and eliminating risk throughout the DOE Complex. One of the greatest challenges being addressed by DOE-EM as this transformation takes place is accelerating the deactivation and decommissioning of thousands of facilities within the DOE Complex that were once used to support nuclear-related programs and projects. These facilities are now unused and aging. Finding solutions to complete the cleanup of these aging facilities more safely, efficiently, and effectively while reducing costs is critical to successfully meeting DOE-EM's cleanup challenge. The Large-Scale Demonstration and Deployment Project (LSDDP) of Hot Cells at the West Valley Demonstration Project (WVDP) is a near-term project funded through the DOE's National Energy Technology Laboratory (DOE-NETL) for the specific purpose of identifying, evaluating, demonstrating, and deploying commercially available technologies that are capable of streamlining the cleanup of hot cells in unused facilities while improving worker safety. Two DOE project sites are participating in this LSDDP: the WVDP site in West Valley, New York and the Hanford River Corridor Project (RCP) site in Richland, Washington. The WVDP site serves as the host site for the project. Technologies considered for demonstration and potential deployment at both LSDDP sites are targeted for application in hot cells that require the use of remote and semi-remote techniques to conduct various cleanup-related activities because of high radiation or high contamination levels. These hot cells, the type of cleanup activities being conducted, and technologies selected for demonstration are the main topics discussed in this paper. The range of cleanup-related activities addressed include in-situ characterization, size-reduction, contamination control, decontamination, in

Demonstration of a Moving-Map System for Improved Lane Navigation of Amphibious Vehicles

National Research Council Canada - National Science Library

Clohrenz, Maura

2003-01-01

The Naval Research Laboratory (NRL) is testing and demonstrating a prototype moving-map system on amphibious vehicles and landing craft to aid the location neutralization and navigation around mines and obstacles in the surf and beach zone...

Solar energy parking canopy demonstration project

Energy Technology Data Exchange (ETDEWEB)

Cylwik, Joe [City of Big Bear Lake, Big Bear, CA (United States); David, Lawrence [City of Big Bear Lake, Big Bear, CA (United States)

2015-09-24

The goal of this pilot/demonstration program is to measure the viability of using solar photovoltaic (PV) technology at three locations in a mountain community environment given the harsh weather conditions. An additional goal is to reduce long-term operational costs, minimize green house gas emissions, lower the dependency on energy produced from fossil fuels, and improve the working environment and health of city employees and residents.

Demonstration of 3 buses fuelled with ethanol with ignition improver in the Netherlands

NARCIS (Netherlands)

Verweij, J.; Weide, J. van der; Nie, L.H. de; Bruin, A. de

1996-01-01

This three year demonstration programme was initiated by OBL, a subsidiary of two Dutch sugar companies, and GADO, a public transport company. The programme was financially supported by a regional governmental organisation (ISP). In this programme, three bio-ethanol fuelled buses accumulated more

Program management plan for the conduct of a research, development, and demonstration program for improving the safety of nuclear powerplants

International Nuclear Information System (INIS)

1981-12-01

Congress passed Public Law 96-567, Nuclear Safety Research, Development, and Demonstration Act of 1980, (hereafter referred to as the Act) to provide for an accelerated and coordinated program of light water reactor safety research, development, and demonstration to be carried out by the Department of Energy. In order to assure that this program would be compatible with the needs of Nuclear Regulatory Commission (NRC) and industry, the Department of Energy (DOE) initiated its response to Section 4 of the Act by conducting individual information gathering meetings with NRC and a wide cross section of the nuclear industry. The Department received recommendations on needs of what type of activities would and would not be appropriate for the Department to assist in satisfying these needs. Based on the evaluation of these inputs, it is concluded that the Department's ongoing Light Water Reactor (LWR) safety program is responsive to the Act. Specifically, the Department's ongoing program includes tasks in the areas of regulatory assessment, risk assessment, fission product source term, and emergency preparedness as well as providing technical assistance to the Institute of Nuclear Power Operations (INPO) to improve training of nuclear power personnel. These were among the very high priority efforts that were identified as necessary and appropriate for support by the Department

Future launcher demonstrator. Challenge and pathfinder

Science.gov (United States)

Kleinau, W.; Guerra, L.; Parkinson, R. C.; Lieberherr, J. F.

1996-02-01

For future and advanced launch vehicles emphasis is focused on single-stage-to-orbit (SSTO) concepts and on completely reusable versions with the goal to reduce the recurrent launch cost, to improve the mission success probability and also safety for the space transportation of economically attractive payloads into Low Earth Orbit. Both issues, the SSTO launcher and the low cost reusability are extremely challenging and cannot be proven by studies and on-ground tests alone. In-flight demonstration tests are required to verify the assumptions and the new technologies, and to justify the new launcher-and operations-concepts. Because a number of SSTO launch vehicles are currently under discussion in terms of configurations and concepts such as winged vehicles for vertical or horizontal launch and landing (from ground or a flying platform), or wingless vehicles for vertical take-off and landing, and also in terms of propulsion (pure rockets or a combination of air breathing and rocket engines), an experimental demonstrator vehicle appears necessary in order to serve as a pathfinder in this area of multiple challenges. A suborbital Reusable Rocket Launcher Demonstrator (RRLD) has been studied recently by a European industrial team for ESA. This is a multipurpose, evolutionary demonstrator, conceived around a modular approach of incremental improvements of subsystems and materials, to achieve a better propellant mass fraction i.e. a better performance, and specifically for the accomplishment of an incremental flight test programme. While the RRLD basic test programme will acquire knowledge about hypersonic flight, re-entry and landing of a cryogenic rocket propelled launcher — and the low cost reusability (short turnaround on ground) in the utilization programme beyond basic testing, the RRLD will serve as a test bed for generic testing of technologies required for the realization of an SSTO launcher. This paper will present the results of the European RRLD study which

Arsenic and Antimony Removal from Drinking Water by Adsorptive Media - U.S. EPA Demonstration Project at South Truckee Meadows General Improvement District (STMGID), NV, Final Performance Evaluation Report

Science.gov (United States)

This report documents the activities performed during and the results obtained from the operation of an arsenic and antimony removal technology demonstrated at the South Truckee Meadows General Improvement District (STMGID) in Washoe County, NV. The objectives of the project wer...

Demonstration of artificial intelligence technology for transit railcar diagnostics

Science.gov (United States)

1999-01-01

This report will be of interest to railcar maintenance professionals concerned with improving railcar maintenance fault-diagnostic capabilities through the use of artificial intelligence (AI) technologies. It documents the results of a demonstration ...

Buried Waste Integrated Demonstration lessons learned: 1993 technology demonstrations

International Nuclear Information System (INIS)

Kostelnik, K.M.; Owens, K.J.

1994-01-01

An integrated technology demonstration was conducted by the Buried Waste Integrated Demonstration (BWID) at the Idaho National Engineering Laboratory Cold Test Pit in the summer of 1993. This program and demonstration was sponsored by the US Department of Energy Office of Technology Development. The demonstration included six technologies representing a synergistic system for the characterization and retrieval of a buried hazardous waste site. The integrated technology demonstration proved very successful and a summary of the technical accomplishments is presented. Upon completion of the integrated technology demonstration, cognizant program personnel participated in a lessons learned exercise. This exercise was conducted at the Simplot Decision Support Center at Idaho State University and lessons learned activity captured additional information relative to the integration of technologies for demonstration purposes. This information will be used by BWID to enhance program planning and strengthen future technology demonstrations

Emphasizing the process of science using demonstrations in conceptual chemistry

Science.gov (United States)

Lutz, Courtney A.

The purpose of this project was to teach students a method for employing the process of science in a conceptual chemistry classroom when observing a demonstration of a discrepant event. Students observed six demonstrations throughout a trimester study of chemistry and responded to each demonstration by asking as many questions as they could think of, choosing one testable question to answer by making as many hypotheses as possible, and choosing one hypothesis to make predictions about observed results of this hypothesis when tested. Students were evaluated on their curiosity, confidence, knowledge of the process of science, and knowledge of the nature of science before and after the six demonstrations. Many students showed improvement in using or mastery of the process of science within the context of conceptual chemistry after six intensive experiences with it. Results of the study also showed students gained confidence in their scientific abilities after completing one trimester of conceptual chemistry. Curiosity and knowledge of the nature of science did not show statistically significant improvement according to the assessment tool. This may have been due to the scope of the demonstration and response activities, which focused on the process of science methodology instead of knowledge of the nature of science or the constraints of the assessment tool.

Decision support software technology demonstration plan

Energy Technology Data Exchange (ETDEWEB)

SULLIVAN,T.; ARMSTRONG,A.

1998-09-01

The performance evaluation of innovative and alternative environmental technologies is an integral part of the US Environmental Protection Agency's (EPA) mission. Early efforts focused on evaluating technologies that supported the implementation of the Clean Air and Clean Water Acts. In 1986 the Agency began to demonstrate and evaluate the cost and performance of remediation and monitoring technologies under the Superfund Innovative Technology Evaluation (SITE) program (in response to the mandate in the Superfund Amendments and Reauthorization Act of 1986 (SARA)). In 1990, the US Technology Policy was announced. This policy placed a renewed emphasis on making the best use of technology in achieving the national goals of improved quality of life for all Americans, continued economic growth, and national security. In the spirit of the technology policy, the Agency began to direct a portion of its resources toward the promotion, recognition, acceptance, and use of US-developed innovative environmental technologies both domestically and abroad. Decision Support Software (DSS) packages integrate environmental data and simulation models into a framework for making site characterization, monitoring, and cleanup decisions. To limit the scope which will be addressed in this demonstration, three endpoints have been selected for evaluation: Visualization; Sample Optimization; and Cost/Benefit Analysis. Five topics are covered in this report: the objectives of the demonstration; the elements of the demonstration plan; an overview of the Site Characterization and Monitoring Technology Pilot; an overview of the technology verification process; and the purpose of this demonstration plan.

Demonstration of Human-Autonomy Teaming Principles

Science.gov (United States)

Shively, Robert Jay

2016-01-01

Known problems with automation include lack of mode awareness, automation brittleness, and risk of miscalibrated trust. Human-Autonomy Teaming (HAT) is essential for improving these problems. We have identified some critical components of HAT and ran a part-task study to introduce these components to a ground station that supports flight following of multiple aircraft. Our goal was to demonstrate, evaluate, and refine HAT principles. This presentation provides a brief summary of the study and initial findings.

Three Soil Quality Demonstrations for Educating Extension Clientele

Science.gov (United States)

Hoorman, James J.

2014-01-01

There is a renewed interest in educating youth, Master Gardeners, and agricultural producers about soil quality. Three soil demonstrations show how soil organic matter increases water holding capacity, improves soil structure, and increases nutrient retention. Exercise one uses clay bricks and sponges to represent mineral soils and soil organic…

An industrial demonstration of computer assisted tomography

International Nuclear Information System (INIS)

Lupton, L.R.

1985-09-01

Computerized tomography (CT) is a nondestructive testing technique for generating quantitative density (linear attenuation coefficient) maps of a cross section through an object. By using a series of parallel tomographic images taken at different elevations, a three-dimensional (3-D) map of the object can be obtained. To demonstrate the power of tomography, a 3-D region of a motorcycle carburetor has been imaged using twenty-four parallel two-dimensional images. From these data, new images in planes orthogonal to the original planes have been generated, thereby improving the user's ability to visualize the position of components within the carburetor. The data have also been used to demonstrate the relationship between tomography and radiography

Demonstration Advanced Avionics System (DAAS) function description

Science.gov (United States)

Bailey, A. J.; Bailey, D. G.; Gaabo, R. J.; Lahn, T. G.; Larson, J. C.; Peterson, E. M.; Schuck, J. W.; Rodgers, D. L.; Wroblewski, K. A.

1982-01-01

The Demonstration Advanced Avionics System, DAAS, is an integrated avionics system utilizing microprocessor technologies, data busing, and shared displays for demonstrating the potential of these technologies in improving the safety and utility of general aviation operations in the late 1980's and beyond. Major hardware elements of the DAAS include a functionally distributed microcomputer complex, an integrated data control center, an electronic horizontal situation indicator, and a radio adaptor unit. All processing and display resources are interconnected by an IEEE-488 bus in order to enhance the overall system effectiveness, reliability, modularity and maintainability. A detail description of the DAAS architecture, the DAAS hardware, and the DAAS functions is presented. The system is designed for installation and flight test in a NASA Cessna 402-B aircraft.

Self Reflections of Undergraduate Students on Using Web-Supported Counterintuitive Science Demonstrations

Science.gov (United States)

Kumar, David Devraj; Dunn, Jessica

2018-03-01

Analysis of self-reflections of undergraduate education students in a project involving web-supported counterintuitive science demonstrations is reported in this paper. Participating students (N = 19) taught science with counterintuitive demonstrations in local elementary school classrooms and used web-based resources accessed via wireless USB adapters. Student reflections to seven questions were analyzed qualitatively using four components of reflection (meeting objectives/perception of learning, dynamics of pedagogy, special needs accommodations, improving teaching) deriving 27 initial data categories and 12 emergent themes. Overall the undergraduates reported meeting objectives, engaging students in pedagogically relevant learning tasks including, providing accommodations to students with special needs, and gaining practice and insight to improve their own teaching. Additional research is needed to arrive at generalizable findings concerning teaching with web-supported counterintuitive science demonstrations in elementary classrooms.

Prototype nickel component demonstration. Final report

International Nuclear Information System (INIS)

Boss, D.E.

1994-01-01

We have been developing a process to produce high-purity nickel structures from nickel carbonyl using chemical vapor deposition (CVD). The prototype demonstration effort had been separated into a number of independent tasks to allow Los Alamos National Laboratory (LANL) the greatest flexibility in tailoring the project to their needs. LANL selected three of the proposed tasks to be performed--Task 1- system modification and demonstration, Task 2-stainless steel mandrel trials, and Task 4-manufacturing study. Task 1 focused on converting the CVD system from a hot-wall to a cold-wall configuration and demonstrating the improved efficiency of the reactor type by depositing a 0.01-inch-thick nickel coating on a cylindrical substrate. Since stainless steel substrates were preferred because of their low α-emitter levels, Task 2 evaluated mandrel configurations which would allow removal of the nickel tube from the substrate. The manufacturing study was performed to develop strategies and system designs for manufacturing large quantities of the components needed for the Sudbury Nuetrino Observatory (SNO) program. Each of these tasks was successfully completed. During these efforts, BIRL successfully produced short lengths of 2-inch-diameter tubing and 6-inch-wide foil with levels of α-radiation emitting contaminants lower than either conventional nickel alloys or electroplated materials. We have produced both the tubing and foil using hot-substrate, cold-wall reactors and clearly demonstrated the advantages of higher precursor efficiency and deposition rate associated with this configuration. We also demonstrated a novel mandrel design which allowed easy removal of the nickel tubing and should dramatically simplify the production of 1.5-meter-long tubes in the production phase of the program

Designing Scholarships to Improve College Success: Final Report on the Performance-Based Scholarship Demonstration

Science.gov (United States)

Mayer, Alexander K.; Patel, Reshma; Rudd, Timothy; Ratledge, Alyssa

2015-01-01

Performance-based scholarships have two main goals: (1) to give students more money for college; and (2) to provide incentives for academic progress. MDRC launched the Performance-Based Scholarship (PBS) Demonstration in 2008 to evaluate the effectiveness of these scholarships in a diverse set of states, institutions, and low-income student…

The ORNL fusion power demonstration study

International Nuclear Information System (INIS)

Shannon, T.E.; Steiner, D.

1978-01-01

In this paper, we review the design approach developed in the ORNL Fusion Power Demonstration Study [1]. The major emphasis of this study is in the application of current and near-term technology as the most logical path to near-term demonstration of tokamak fusion power. In addition we are pursuing a number of concepts to simplify the tokamak reactor to be more acceptable to the utility industry as a future source of energy. The discussion will focus on the areas having the greatest overall impact on reactor feasibility: 1) overall size and power output, 2) remote maintenance considerations, 3) electrical power supplies, 4) blanket design; and 5) economics. The tokamak device, by nature of its configuration and pulsed operation, is an exceptionally complex engineering design problem. We have concluded that innovative design concepts are essential to cope with this basic complexity. We feel that the feasibility of tokamak fusion power has been significantly improved by these design approaches. (author)

Task plan for TARA-II compaction and grouting demonstration

International Nuclear Information System (INIS)

Spalding, B.P.

1991-11-01

This task directly supports the corrective measures evaluation for the closure of Solid Waste Storage Area (SWSA) 6 but also supports technology development for the closure of other Oak Ridge National Laboratory (ORNL) SWSAs and waste management units. Previous demonstrations have established the effectiveness of dynamic compaction and in situ grouting in stabilizing burial trenches against subsidence, which would otherwise compromise the support of infiltration barrier structures designed to protect buried waste from leaching. In situ grouting with polyacrylamide has also been demonstrated to improve the hydrologic isolation of buried waste. Both of these stabilization techniques have been demonstrated on burial trenches that are situated well above the water table and, hence, are in a chronic unsaturated moisture regime. Further demonstrations of these shallow-land burial trench stabilization techniques are necessary to establish their effectiveness and safety when applied to burial trenches that are chronically inundated with groundwater

Drilling for improvement : Statoil and Halliburton report significant cost savings and more accurate well placement at the Leismer demonstration project

Energy Technology Data Exchange (ETDEWEB)

Jaremko, D.

2010-07-15

This article discussed new improvements in steam assisted gravity drainage (SAGD) made by Statoil and Halliburton at the Leismer demonstration project. The Leismer project is Statoil's inaugural project in oil sands development, and will have a capacity to produce 10,000 barrels per day through 4 separate well pads with 23 well pairs. Challenges to the project included the long lateral sections required for the well pairs to remain parallel to each other while remaining within the target formation. An azimuthal deep resistivity (ADR) tool was used to detect the proximity of the wellbore to shale and water zones. Use of the tool allowed operators to modify the planned well trajectory in order to optimize placements within the reservoir. A rotary steerable system (RSS) was used increase injection times. The project was completed 6 to 8 weeks ahead of schedule. Applications have now been filed for a further 10 phases that will produce 240,000 barrels per day. 1 fig.

Parker Hybrid Hydraulic Drivetrain Demonstration

Energy Technology Data Exchange (ETDEWEB)

Collett, Raymond [Parker-Hannifin Corporation, Cleveland, OH (United States); Howland, James [Parker-Hannifin Corporation, Cleveland, OH (United States); Venkiteswaran, Prasad [National Energy Technology Lab. (NETL), Morgantown, WV (United States)

2014-03-31

This report examines the benefits of Parker Hannifin hydraulic hybrid brake energy recovery systems used in commercial applications for vocational purposes. A detailed background on the problem statement being addressed as well as the solution set specific for parcel delivery will be provided. Objectives of the demonstration performed in high start & stop applications included opportunities in fuel usage reduction, emissions reduction, vehicle productivity, and vehicle maintenance. Completed findings during the demonstration period and parallel investigations with NREL, CALSTART, along with a literature review will be provided herein on this research area. Lastly, results identified in the study by third parties validated the savings potential in fuel reduction of on average of 19% to 52% over the baseline in terms of mpg (Lammert, 2014, p11), Parker data for parcel delivery vehicles in the field parallels this at a range of 35% - 50%, emissions reduction of 17.4% lower CO2 per mile and 30.4% lower NOx per mile (Gallo, 2014, p15), with maintenance improvement in the areas of brake and starter replacement, while leaving room for further study in the area of productivity in terms of specific metrics that can be applied and studied.

Secure Interoperable Open Smart Grid Demonstration Project

Energy Technology Data Exchange (ETDEWEB)

Magee, Thoman [Consolidated Edison Company Of New York, Inc., NY (United States)

2014-12-28

The Consolidated Edison, Inc., of New York (Con Edison) Secure Interoperable Open Smart Grid Demonstration Project (SGDP), sponsored by the United States (US) Department of Energy (DOE), demonstrated that the reliability, efficiency, and flexibility of the grid can be improved through a combination of enhanced monitoring and control capabilities using systems and resources that interoperate within a secure services framework. The project demonstrated the capability to shift, balance, and reduce load where and when needed in response to system contingencies or emergencies by leveraging controllable field assets. The range of field assets includes curtailable customer loads, distributed generation (DG), battery storage, electric vehicle (EV) charging stations, building management systems (BMS), home area networks (HANs), high-voltage monitoring, and advanced metering infrastructure (AMI). The SGDP enables the seamless integration and control of these field assets through a common, cyber-secure, interoperable control platform, which integrates a number of existing legacy control and data systems, as well as new smart grid (SG) systems and applications. By integrating advanced technologies for monitoring and control, the SGDP helps target and reduce peak load growth, improves the reliability and efficiency of Con Edison’s grid, and increases the ability to accommodate the growing use of distributed resources. Con Edison is dedicated to lowering costs, improving reliability and customer service, and reducing its impact on the environment for its customers. These objectives also align with the policy objectives of New York State as a whole. To help meet these objectives, Con Edison’s long-term vision for the distribution grid relies on the successful integration and control of a growing penetration of distributed resources, including demand response (DR) resources, battery storage units, and DG. For example, Con Edison is expecting significant long-term growth of DG

Does quality improvement work in neonatology improve clinical outcomes?

Science.gov (United States)

Ellsbury, Dan L; Clark, Reese H

2017-04-01

Quality improvement initiatives in neonatology have been promoted as an important way of improving outcomes of newborns. The purpose of this review is to examine the effectiveness of recent quality improvement work in improving the outcomes of infants requiring neonatal intensive care. Quality improvement collaboratives and single-center projects demonstrate improvement of clinical processes and outcomes in neonatology that impact both preterm and term infants. Declines in morbidities, resource use, and length of stay have been associated with reductions in healthcare costs. Recent quality improvement work has shown evidence of improvement in clinical outcomes in neonatal intensive care patients. These improvements have important implications for the reduction of healthcare costs in this population.

ASTRID: Advanced Sodium Technological Reactor for Industrial Demonstration

International Nuclear Information System (INIS)

Vasile, A.

2012-01-01

Conclusions: • R&D results [CEA-AREVA-EDF] obtained from 2007 to 2009 have contributed to ASTRID mid 2010 choice of options; • ASTRID has the objective to demonstrate at the industrial scale progress in the identified domains of SFR weakness (safety, operability, economy). and to perform transmutation demonstrations; • A lot of improvements are related to safety; • The first very important milestone is 2012 (June 2006 French Act on wastes management): – ASTRID pre-conceptual design studies: 2010-2012; – First investment cost evaluation; – First safety Authorities advice on the orientations for ASTRID safety; • With the ASTRID program funded by the French government, France has the opportunity to develop a GEN IV Sodium Fast Reactor

VOC-Arid Integrated Demonstration guide to preparation of demonstration documents

International Nuclear Information System (INIS)

Jensen, E.J.; Brouns, T.M.; Koegler, K.J.; McCabe, G.H.; Morris, F.A.

1994-06-01

This guide has been prepared by Demonstration Operations of the Volatile Organic Compound-Arid Integrated Demonstration (VOC-Arid ID). Its purpose is to describe demonstration documents, designate responsibilities for these documents, and guide the Principal Investigator (PI) and others in their preparation. The main emphasis of this guide is to describe the documentation required of the PI. However, it does cover some of the responsibilities of other members of the VOC-Arid ID team. The VOC-Arid ID is one of several US Department of Energy (DOE) integrated demonstrations designed to support the demonstration of emerging environmental management and restoration technologies. The principal objective of the VOC-Arid ID is to identify, develop, and demonstrate new and innovative technologies for environmental restoration at arid or semiarid sites containing volatile organic compounds with or without associated contamination (e.g., radionuclides and metals)

Strengthening global health security capacity--Vietnam demonstration project, 2013.

Science.gov (United States)

Tran, Phu Dac; Vu, Long Ngoc; Nguyen, Hien Tran; Phan, Lan Trong; Lowe, Wayne; McConnell, Michelle S; Iademarco, Michael F; Partridge, Jeffrey M; Kile, James C; Do, Trang; Nadol, Patrick J; Bui, Hien; Vu, Diep; Bond, Kyle; Nelson, David B; Anderson, Lauren; Hunt, Kenneth V; Smith, Nicole; Giannone, Paul; Klena, John; Beauvais, Denise; Becknell, Kristi; Tappero, Jordan W; Dowell, Scott F; Rzeszotarski, Peter; Chu, May; Kinkade, Carl

2014-01-31

Over the past decade, Vietnam has successfully responded to global health security (GHS) challenges, including domestic elimination of severe acute respiratory syndrome (SARS) and rapid public health responses to human infections with influenza A(H5N1) virus. However, new threats such as Middle East respiratory syndrome coronavirus (MERS-CoV) and influenza A(H7N9) present continued challenges, reinforcing the need to improve the global capacity to prevent, detect, and respond to public health threats. In June 2012, Vietnam, along with many other nations, obtained a 2-year extension for meeting core surveillance and response requirements of the 2005 International Health Regulations (IHR). During March-September 2013, CDC and the Vietnamese Ministry of Health (MoH) collaborated on a GHS demonstration project to improve public health emergency detection and response capacity. The project aimed to demonstrate, in a short period, that enhancements to Vietnam's health system in surveillance and early detection of and response to diseases and outbreaks could contribute to meeting the IHR core capacities, consistent with the Asia Pacific Strategy for Emerging Diseases. Work focused on enhancements to three interrelated priority areas and included achievements in 1) establishing an emergency operations center (EOC) at the General Department of Preventive Medicine with training of personnel for public health emergency management; 2) improving the nationwide laboratory system, including enhanced testing capability for several priority pathogens (i.e., those in Vietnam most likely to contribute to public health emergencies of international concern); and 3) creating an emergency response information systems platform, including a demonstration of real-time reporting capability. Lessons learned included awareness that integrated functions within the health system for GHS require careful planning, stakeholder buy-in, and intradepartmental and interdepartmental coordination and

Demonstration of Focusing Wolter Mirrors for Neutron Phase and Magnetic Imaging

Directory of Open Access Journals (Sweden)

Daniel S. Hussey

2018-03-01

Full Text Available Image-forming focusing mirrors were employed to demonstrate their applicability to two different modalities of neutron imaging, phase imaging with a far-field interferometer, and magnetic-field imaging through the manipulation of the neutron beam polarization. For the magnetic imaging, the rotation of the neutron polarization in the magnetic field was measured by placing a solenoid at the focus of the mirrors. The beam was polarized upstream of the solenoid, while the spin analyzer was situated between the solenoid and the mirrors. Such a polarized neutron microscope provides a path toward considerably improved spatial resolution in neutron imaging of magnetic materials. For the phase imaging, we show that the focusing mirrors preserve the beam coherence and the path-length differences that give rise to the far-field moiré pattern. We demonstrated that the visibility of the moiré pattern is modified by small angle scattering from a highly porous foam. This experiment demonstrates the feasibility of using Wolter optics to significantly improve the spatial resolution of the far-field interferometer.

The evaluation of the National Long Term Care Demonstration. 1. An overview of the channeling demonstration and its evaluation.

OpenAIRE

Carcagno, G J; Kemper, P

1988-01-01

The channeling demonstration sought to substitute community care for nursing home care to reduce long-term care costs and improve the quality of life of elderly clients and the family members and friends who care for them. Two interventions were tested, each in five sites; both had comprehensive case management at their core. One model added a small amount of additional funding for direct community services to fill the gaps in the existing system; the other substantially expanded coverage of ...

Polyethylene encapsulation full-scale technology demonstration. Final report

International Nuclear Information System (INIS)

Kalb, P.D.; Lageraaen, P.R.

1994-10-01

A full-scale integrated technology demonstration of a polyethylene encapsulation process, sponsored by the US Department of Energy (DOE) Office of Technology Development (OTD), was conducted at the Environmental ampersand Waste Technology Center at Brookhaven National Laboratory (BNL.) in September 1994. As part of the Polymer Solidification National Effort, polyethylene encapsulation has been developed and tested at BNL as an alternative solidification technology for improved, cost-effective treatment of low-level radioactive (LLW), hazardous and mixed wastes. A fully equipped production-scale system, capable of processing 900 kg/hr (2000 lb/hr), has been installed at BNL. The demonstration covered all facets of the integrated processing system including pre-treatment of aqueous wastes, precise feed metering, extrusion processing, on-line quality control monitoring, and process control

Technology demonstration of space intravehicular automation and robotics

Science.gov (United States)

Morris, A. Terry; Barker, L. Keith

1994-01-01

Automation and robotic technologies are being developed and capabilities demonstrated which would increase the productivity of microgravity science and materials processing in the space station laboratory module, especially when the crew is not present. The Automation Technology Branch at NASA Langley has been working in the area of intravehicular automation and robotics (IVAR) to provide a user-friendly development facility, to determine customer requirements for automated laboratory systems, and to improve the quality and efficiency of commercial production and scientific experimentation in space. This paper will describe the IVAR facility and present the results of a demonstration using a simulated protein crystal growth experiment inside a full-scale mockup of the space station laboratory module using a unique seven-degree-of-freedom robot.

Results from an in-plant demonstration of intelligent control

International Nuclear Information System (INIS)

Edwards, R.M.; Garcia, H.E.; Messick, N.

1993-01-01

A learning systems-based reconfigurable controller was demonstrated on the deaerating feedwater heater at the Experimental Breeder Reactor II (EBR-II) on April 1, 1993. Failures of the normal pressure regulating process were introduced by reducing the steam flow to the heater by as much as 10%. The controller maintained pressure in the heater at acceptable levels for several minutes, whereas operator intervention would have otherwise been required within a few seconds. This experiment demonstrates the potential of advanced control techniques for improving safety, reliability, and performance of power plant operations as well as the utility of EBR-II as an experimental power plant controls facility

Improving Project Portfolio Management (PPM) for Improvement Projects

DEFF Research Database (Denmark)

Pries-Heje, Jan; Jakobsen, Peter M.; Korsaa, Morten

2017-01-01

Project Portfolio Management (PPM) focus on the integration and alignment of projects with the business operation in order to achieve most value and cost-efficiency for the investment in projects. PPM is often a challenge and especially so for improvement projects where PPM is considerably...... of evaluating a portfolio of improvement projects and combine this evaluation with the effect they have on the CMMI maturity level. Further, the paper demonstrates how the combination of a strong senior management requirement for improved maturity and the focus on getting the most value out of PPM made...

Providing Demonstrable Return-on-Investment for Organisational Learning and Training

Science.gov (United States)

Elliott, Michael; Dawson, Ray; Edwards, Janet

2009-01-01

Purpose: The aim of this paper is to present a holistic approach to training, that clearly demonstrates cost savings with improved effectiveness and efficiencies that are aligned to business objectives. Design/methodology/approach: Extending Kirkpatrick's evaluation framework with Phillips's return-on-investment (ROI) concepts, the paper conveys a…

Demonstration tests for manufacturing the ITER vacuum vessel

International Nuclear Information System (INIS)

Shimizu, Katsusuke; Onozuka, Masanori; Usui, Yukinori; Urata, Kazuhiro; Tsujita, Yoshihiro; Nakahira, Masataka; Takeda, Nobukazu; Kakudate, Satoshi; Ohmori, Junji; Shibanuma, Kiyoshi

2007-01-01

Demonstration tests for manufacturing and assembly of the International Thermonuclear Experimental Reactor (ITER) vacuum vessel have been conducted to confirm manufacturing and assembly process of the vacuum vessel (VV). The full-scale partial mock-up fabrication was planned and is in progress. The results will be available in the near future. Field-joint assembly procedure has been demonstrated using a test stand. Due to limited accessibility to the outer shell at the field joint, some operations, including alignment of the splice plates, field-joint welding, and examination, were found to be very difficult. In addition, a demonstration test on the selected back-seal structures was performed. It was found that the tested structures have insufficient sealing capabilities and need further improvement. The applicability of ultrasonic testing methods has been investigated. Although side drilled holes of 2.4 mm in diameter were detected, detection of the slit-type defects and defect characterization were found to be difficult. Feasibility test of liquid penetrant testing has revealed that the selected liquid penetrant testing (LPT) solutions have sufficient low outgas rates and are applicable to the VV

Demonstration tests for manufacturing the ITER vacuum vessel

Energy Technology Data Exchange (ETDEWEB)

Shimizu, Katsusuke [Mitsubishi Heavy Industries, Ltd., Kobe Shipyard and Machinery Works, Wadasaki-cho 1-1-1, Hyogo-ku, Kobe 652-8585 (Japan)], E-mail: katsusuke_shimizu@mhi.co.jp; Onozuka, Masanori [Mitsubishi Heavy Industries, Ltd., Konan 2-16-5, Minato-ku, Tokyo 108-8215 (Japan); Usui, Yukinori; Urata, Kazuhiro; Tsujita, Yoshihiro [Mitsubishi Heavy Industries, Ltd., Kobe Shipyard and Machinery Works, Wadasaki-cho 1-1-1, Hyogo-ku, Kobe 652-8585 (Japan); Nakahira, Masataka; Takeda, Nobukazu; Kakudate, Satoshi; Ohmori, Junji; Shibanuma, Kiyoshi [Japan Atomic Energy Agency, Mukouyama 801-1, Naka-machi, Naka-gun, Ibaraki 311-0193 (Japan)

2007-10-15

Demonstration tests for manufacturing and assembly of the International Thermonuclear Experimental Reactor (ITER) vacuum vessel have been conducted to confirm manufacturing and assembly process of the vacuum vessel (VV). The full-scale partial mock-up fabrication was planned and is in progress. The results will be available in the near future. Field-joint assembly procedure has been demonstrated using a test stand. Due to limited accessibility to the outer shell at the field joint, some operations, including alignment of the splice plates, field-joint welding, and examination, were found to be very difficult. In addition, a demonstration test on the selected back-seal structures was performed. It was found that the tested structures have insufficient sealing capabilities and need further improvement. The applicability of ultrasonic testing methods has been investigated. Although side drilled holes of 2.4 mm in diameter were detected, detection of the slit-type defects and defect characterization were found to be difficult. Feasibility test of liquid penetrant testing has revealed that the selected liquid penetrant testing (LPT) solutions have sufficient low outgas rates and are applicable to the VV.

FINAL SIMULATION RESULTS FOR DEMONSTRATION CASE 1 AND 2

Energy Technology Data Exchange (ETDEWEB)

David Sloan; Woodrow Fiveland

2003-10-15

The goal of this DOE Vision-21 project work scope was to develop an integrated suite of software tools that could be used to simulate and visualize advanced plant concepts. Existing process simulation software did not meet the DOE's objective of ''virtual simulation'' which was needed to evaluate complex cycles. The overall intent of the DOE was to improve predictive tools for cycle analysis, and to improve the component models that are used in turn to simulate equipment in the cycle. Advanced component models are available; however, a generic coupling capability that would link the advanced component models to the cycle simulation software remained to be developed. In the current project, the coupling of the cycle analysis and cycle component simulation software was based on an existing suite of programs. The challenge was to develop a general-purpose software and communications link between the cycle analysis software Aspen Plus{reg_sign} (marketed by Aspen Technology, Inc.), and specialized component modeling packages, as exemplified by industrial proprietary codes (utilized by ALSTOM Power Inc.) and the FLUENT{reg_sign} computational fluid dynamics (CFD) code (provided by Fluent Inc). A software interface and controller, based on an open CAPE-OPEN standard, has been developed and extensively tested. Various test runs and demonstration cases have been utilized to confirm the viability and reliability of the software. ALSTOM Power was tasked with the responsibility to select and run two demonstration cases to test the software--(1) a conventional steam cycle (designated as Demonstration Case 1), and (2) a combined cycle test case (designated as Demonstration Case 2). Demonstration Case 1 is a 30 MWe coal-fired power plant for municipal electricity generation, while Demonstration Case 2 is a 270 MWe, natural gas-fired, combined cycle power plant. Sufficient data was available from the operation of both power plants to complete the cycle

Case Study for the ARRA-funded GSHP Demonstration at University at Albany

Energy Technology Data Exchange (ETDEWEB)

Liu, Xiaobing [ORNL; Malhotra, Mini [ORNL; Xiong, Zeyu [ORNL

2015-03-01

High initial costs and lack of public awareness of ground-source heat pump (GSHP) technology are the two major barriers preventing rapid deployment of this energy-saving technology in the United States. Under the American Recovery and Reinvestment Act (ARRA), 26 GSHP projects have been competitively selected and carried out to demonstrate the benefits of GSHP systems and innovative technologies for cost reduction and/or performance improvement. This report highlights the findings of a case study of one of the ARRA-funded GSHP demonstration projects—a distributed GSHP system at a new 500-bed apartment-style student residence hall at the University at Albany. This case study is based on the analysis of detailed design documents, measured performance data, published catalog data of heat pump equipment, and actual construction costs. Simulations with a calibrated computer model are performed for both the demonstrated GSHP system and a baseline heating, ventilation, and airconditioning (HVAC) system to determine the energy savings and other related benefits achieved by the GSHP system. The evaluated performance metrics include the energy efficiency of the heat pump equipment and the overall GSHP system, as well as the pumping performance, energy savings, carbon emission reductions, and cost-effectiveness of the demonstrated GSHP system compared with the baseline HVAC system. This case study also identifies opportunities for improving the operational efficiency of the demonstrated GSHP system.

Contribution to a Danish action plan for development and demonstration of CHP from solid biomass; Oplaeg til en national handlingsplan for udvikling og demonstration indenfor kraftvarme fra fast biomasse

Energy Technology Data Exchange (ETDEWEB)

Hansen, Morten Tony

2011-01-15

The report is the contribution from the industry to an action plan for development and demonstration of CHP technology for solid biomass. The report aims to serve as inspiration and basis for administrators and applicants of Danish funding schemes for development and demonstration in future tenders. Although Danish-based cogeneration technologies for solid biofuels are advanced compared to the competitors in many areas there is a large need to continuously improve the technology by sustained development and demonstration activities. The aim is to overcome the technological barriers that this project has identified and thus maintain competitiveness. The industry currently has very strong focus on market deployment of especially technologies for cogeneration in small scale (up to 15 MW thermal power) and on the overall economy of these plants. Reference installations that displays many operational hours with a reasonable economy, are crucial for investors. Currently, no companies market commercial plants that have sufficiently low costs to operate under Danish conditions and few do for the conditions found internationally. Thus, from the industry perspective there is still a need for development and demonstration of CHP technology below 15 MW thermal. The analysis does not exclude any technology tracks, but the development and demonstration efforts should lead to improvements in conditions such as availability, efficiencies and operating and maintenance costs. Also technologies for large plants and systems need to be improved with respect to availability and efficiency and reduced operating and maintenance costs. For all technologies, there is a need to develop the use of special solid biofuels that on the one hand may have troublesome characteristics but on the other may help lower operating costs. The Danish-based companies have good opportunities to find support for the development and demonstration effort. A number of support programs and pools are in place and

Evaluation and demonstration of methods for improved fuel utilization. Second semi-annual progress report, April 1, 1980-September 30, 1980

International Nuclear Information System (INIS)

1981-01-01

Demonstrations are being performed in the Fort Calhoun reactor. The current program consists of two parts, one to demonstrate low leakage fuel management (SAVFUEL - Shimmed And Very Flexible Uranium Element Loading) and the other to demonstrate high burnup. The first part will demonstrate that the power duty cycle which is characteristic of SAVFUEL does not have a deleterious effect on fuel performance, while the second part will demonstrate that the peak rod average burnup of the current 14 x 14 fuel design can be increased to 45 GWD/T. A visual examination conducted at poolside was completed on four fuel assemblies which are scheduled to demonstrate the SAVFUEL power cycle and seventeen fuel assemblies which are scheduled to provide high burnup fuel performance data. Results of visual examinations, shoulder gap closure, fuel assembly growth, and fuel rod channel width measurements are reported which show excellent fuel performance for the high burnup; demonstration assemblies after four exposure cycles. These results support an additional exposure cycle for the high burnup demonstration assemblies which currently have an assembly average burnup up to 37 GWD/T

Documentation of Improvement Competences

DEFF Research Database (Denmark)

Johansen, Jørn; Back, Karsten Kristensen; Korsaa, Morten

2017-01-01

This paper demonstrates how a report used in a Master in Project management and Process improvement training at Roskilde University Denmark can be used to evaluate if a student can pass the ECQA SPI Manager exam. It also demonstrates how the structure of the report addresses all necessary...... Manager job role, which is based on the SPI Manifesto and the ImprovAbilityTM model (part of ISO/IEC 33014 Guideline for Process Improvement) among other types of knowledge and research....... competences, which should or could be brought into play during the project – and therefor also in one way or another addresses the quality of the activated competences in the improvement project – a kind of qualification. The clue is that the structure of the report follows the units and element in the SPI...

Defense waste cyclone incinerator demonstration program: October--March 1979

International Nuclear Information System (INIS)

Klinger, L.M.

1979-01-01

The cyclone incinerator developed at Mound has proven to be an effective tool for waste volume reduction. During the first half of FY-1979, efforts have been made to increase the versatility of the system. Incinerator development was continued in three areas. Design changes were drafted for the present developmental incinerator to rectify several minor operational deficiencies of the system. Improvements will be limited to redesign unless installation is required to prove design or to permit implementation of other portions of the plan. The applications development portion of the feasibility plan is focused upon expanding the versatility of the incinerator. An improved delivery system was installed for burning various liquids. An improved continuous feed system was installed and will be demonstrated later this year. Late in FY-1979, work will begin on the conceptual design of a production cyclone incinerator which will handle nonrecoverable TRU waste, and which will fully demonstrate the capabilities of the cyclone incinerator system. Data generated in past years and during FY-1979 are being collected to establish cyclone incineration effects on solids, liquids, and gases in the system. Data reflecting equipment life cycles and corrosion have been tabulated. Basic design criteria for a cyclone incinerator system based on developmental work on the incinerator through FY-1979 have been assembled. The portion of the material dealing with batch-type operation of the incinerator will be published later this year

Proposed success demonstration criteria for the Department of Energy's waste reduction efforts

International Nuclear Information System (INIS)

Suffern, J.S.

1990-01-01

Seven proposed criteria for demonstration of success in waste reduction have been developed: reduced amount of hazardous waste, reduced waste management cost, improved regulatory compliance, reduced health risk, increased production efficiency, reduced accident risk, and improved public relations. A detailed description of each of the criteria is presented along with a discussion for each of the mechanisms for measurement, required commitments, strengths, and weaknesses. 2 refs

The evaluation of the National Long Term Care Demonstration. 1. An overview of the channeling demonstration and its evaluation.

Science.gov (United States)

Carcagno, G J; Kemper, P

1988-04-01

The channeling demonstration sought to substitute community care for nursing home care to reduce long-term care costs and improve the quality of life of elderly clients and the family members and friends who care for them. Two interventions were tested, each in five sites; both had comprehensive case management at their core. One model added a small amount of additional funding for direct community services to fill the gaps in the existing system; the other substantially expanded coverage of community services regardless of categorical eligibility under existing programs. The demonstration was evaluated using a randomized experimental design to test the effects of channeling on use of community care, nursing homes, hospitals, and informal caregiving, and on measures of the quality of life of clients and their informal caregivers. Data were obtained from interviews with clients and informal caregivers; service use and cost records came from Medicare, Medicaid, channeling, and providers; and death records for an 18-month follow-up period were examined.

Demonstration of Software Application Biogas Optimizer at the Haendeloe Biogas Site

Energy Technology Data Exchange (ETDEWEB)

Cook, Kristofer (Bioprocess Control Sweden AB, Lund (SE))

2008-04-15

There is a growing interest in the utilisation of process optimisation technologies within the biogas industry. This trend is being driven by new and growing market opportunities as well as an interest to improve the overall profitability of commercial biogas processes. Biogas Optimizer, developed by Bioprocess Control Sweden AB based in Lund, Sweden, represents one such process optimisation technology, utilising a supervisory and control approach to improve both biogas production efficiency and process stability. A demonstration project was conducted over a nine month period during 2007 at the Haendeloe biogas plant in Norrkoeping, Sweden, owned and operated by Svensk Biogas AB, to provide an indication of the potential of Biogas Optimizer to improve the competitiveness of biogas producers. The demonstration project attempted to satisfy 3 goals, namely; 1) to obtain baseline production information regarding the average Organic Loading Rate (OLR) and average Biogas Production Rate (BPR), 2) to demonstrate that the technology behind Biogas Optimizer works under full-scale production conditions, and 3) to verify that significant/notable production efficiency improvements can be achieved utilising Biogas Optimizer when compared to baseline production information, and that biogas production can be optimised for maximising the utilisation of reactor capacity while still leaving a comfortable safety margin so as to avoid reactor overloading. The collection of baseline production information during three months resulted in an average OLR of 4.0 Kg VS/m3/day and average BPR of 2.6 Nm3/m3/day being selected as baseline data from which to compare the performance of Biogas Optimizer. The full-scale demonstration of Biogas Optimizer was conducted over a 40 day period. During these 40 days, OLR recommendations from Biogas Optimizer, and the resulting manual adjustment of the OLR by the plant operator, resulted in an increase in the average OLR from 4.0 to 4.7 Kg/m3/day and

Update on Nonsurgical Lung Volume Reduction Procedures

Directory of Open Access Journals (Sweden)

J. Alberto Neder

2016-01-01

Full Text Available There has been a surge of interest in endoscopic lung volume reduction (ELVR strategies for advanced COPD. Valve implants, coil implants, biological LVR (BioLVR, bronchial thermal vapour ablation, and airway stents are used to induce lung deflation with the ultimate goal of improving respiratory mechanics and chronic dyspnea. Patients presenting with severe air trapping (e.g., inspiratory capacity/total lung capacity (TLC 225% predicted and thoracic hyperinflation (TLC > 150% predicted have the greatest potential to derive benefit from ELVR procedures. Pre-LVRS or ELVR assessment should ideally include cardiological evaluation, high resolution CT scan, ventilation and perfusion scintigraphy, full pulmonary function tests, and cardiopulmonary exercise testing. ELVR procedures are currently available in selected Canadian research centers as part of ethically approved clinical trials. If a decision is made to offer an ELVR procedure, one-way valves are the first option in the presence of complete lobar exclusion and no significant collateral ventilation. When the fissure is not complete, when collateral ventilation is evident in heterogeneous emphysema or when emphysema is homogeneous, coil implants or BioLVR (in that order are the next logical alternatives.

Waste and Disposal: Concept and Demonstration

International Nuclear Information System (INIS)

Neerdael, B.; Buyens, M.; De Bruyn, D.; Volckaert, G.

2001-01-01

Principal achievements in 2000 with regard to the PRACLAY programme are presented. The PRACLAY project has been conceived to demonstrate the construction and the operation of a gallery for the disposal of HLW in a clay formation. Within this context, various aspects concerning design and operation are investigated.The PRACLAY experiment will contribute to enhance understanding of water flow and mass transport in dense clay-based materials as well as to improve the design of the reference disposal concept. In 2000, efforts were focussed on the operation of the OPHELIE mock-up, which is a surface experiment designed to prepare and to complement PRACLAY-related experimental work in the HADES Underground Research Laboratory

Smart Columbus : Systems Engineering Management Plan (SEMP) for Smart Columbus Demonstration Program

Science.gov (United States)

2018-01-16

The Smart City Demonstration Program is intended to improve access through expanded mobility options in major job centers, enhance visitor experience by better connecting visitors to transportation options, stimulate regional economic prosperity and ...

USEPA'S SMALL DRINKING WATER TREATMENT TECHNOLOGY DEMONSTRATIONS IN ECUADOR AND MEXICO

Science.gov (United States)

In order to support and help in the struggle to improve the quality of drinking water in the United States and abroad, the United States Environmental Protection Agency (USEPA) conducts research studies for the demonstration and evaluation of alternative and innovative drinking w...

Field demonstration of improved shallow land burial practices for low-level radioactive solid wastes: preliminary site characterization and progress report

International Nuclear Information System (INIS)

Vaughan, N.D.; Haase, C.S.; Huff, D.D.; Lee, S.Y.; Walls, E.C.

1982-12-01

A 5-year field demonstration (ETF) of improved shallow land burial practices for low-level radioactive solid wastes in a humid environment evaluates the use of a trench liner and grout as alternate trench treatments for improving shallow land burial site performance in the humid East. The ETF is located within the Copper Creek thrust block of the Valley and Ridge Province of east Tennessee and is underlain by strata of the Middle to Late Cambrian Conasauga Group. The Maryville Limestone formation, which is composed of ribbon-bedded and interclastic limestones and dark grey shales and mudstones, comprises the bedrock immediately beneath the site. The bedrock and residuum structure are characterized by anticlinal folds with numerous joints and fractures, some of which are filled with calcite. Seismic and electrical resistivity geophysical methods were useful in characterizing the thickness of residuum and presence of structural features. Soils are illitic and range from podzolic to lithosols to alluvial in the vicinity of the ETF, but the original soil solum was removed in 1975 when the mixed hardwood forest was cleared and the site was planted in grasses. The remaining residuum consists of acidic soil aggregate and extensively weathered siltstone and sandstone which exhibit the original rock structure. Mean annual precipitation at the site is 1500 mm, although during the initial study period (10-1-80 to 9-30-81) the annual total was 939 mm. Runoff was estimated to be about 50% of the precipitation total, based on observations at two Parshall flumes installed at the site. Storm runoff is quite responsive to rainfall, and the lag time between peak rainfall and runoff is less than 15 min during winter storms. Tracer studies of the ground-water system, suggest that ground-water flow has two distinct components, one associated with fracture flow and the other with intergranular flow

Fuel Gas Demonstration Plant Program. Volume I. Demonstration plant

Energy Technology Data Exchange (ETDEWEB)

1979-01-01

The objective of this project is for Babcock Contractors Inc. (BCI) to provide process designs, and gasifier retort design for a fuel gas demonstration plant for Erie Mining Company at Hoyt Lake, Minnesota. The fuel gas produced will be used to supplement natural gas and fuel oil for iron ore pellet induration. The fuel gas demonstration plant will consist of five stirred, two-stage fixed-bed gasifier retorts capable of handling caking and non-caking coals, and provisions for the installation of a sixth retort. The process and unit design has been based on operation with caking coals; however, the retorts have been designed for easy conversion to handle non-caking coals. The demonstration unit has been designed to provide for expansion to a commercial plant (described in Commercial Plant Package) in an economical manner.

Joint optimization of phase diversity and adaptive optics : Demonstration of potential

NARCIS (Netherlands)

Korkiakoski, V.; Keller, C.U.; Doelman, N.; Fraanje, P.R.; Verhaegen, M.H.G.

2011-01-01

We study different possibilities to use adaptive optics (AO) and phase diversity (PD) together in a jointly optimized system. The potential of the joint system is demonstrated through numerical simulations. We find that the most significant benefits are obtained from the improved deconvolution of

Solar architecture in The Netherlands : demonstration in the district of tomorrow

NARCIS (Netherlands)

Ritzen, M.J.; Geurts, C.P.W.; Vroon, Zeger; Rovers, R.

2015-01-01

Integration of PV in the Building Envelope (BIPV) is one of the four key developments necessary for large market PV penetration, together with PV efficiency improvement, price decrease and electricity storage [1]. In the course of BIPV development, demonstration projects are realized worldwide to

A low-cost approach for rapidly creating demonstration models for hands-on learning

Science.gov (United States)

Kinzli, Kristoph-Dietrich; Kunberger, Tanya; O'Neill, Robert; Badir, Ashraf

2018-01-01

Demonstration models allow students to readily grasp theory and relate difficult concepts and equations to real life. However drawbacks of using these demonstration models are that they are can be costly to purchase from vendors or take a significant amount of time to build. These two limiting factors can pose a significant obstacle for adding demonstrations to the curriculum. This article presents an assignment to overcome these obstacles, which has resulted in 36 demonstration models being added to the curriculum. The article also presents the results of student performance on course objectives as a result of the developed models being used in the classroom. Overall, significant improvement in student learning outcomes, due to the addition of demonstration models, has been observed.

Water Use Optimization Toolset Project: Development and Demonstration Phase Draft Report

Energy Technology Data Exchange (ETDEWEB)

Gasper, John R. [Argonne National Laboratory; Veselka, Thomas D. [Argonne National Laboratory; Mahalik, Matthew R. [Argonne National Laboratory; Hayse, John W. [Argonne National Laboratory; Saha, Samrat [Argonne National Laboratory; Wigmosta, Mark S. [PNNL; Voisin, Nathalie [PNNL; Rakowski, Cynthia [PNNL; Coleman, Andre [PNNL; Lowry, Thomas S. [SNL

2014-05-19

This report summarizes the results of the development and demonstration phase of the Water Use Optimization Toolset (WUOT) project. It identifies the objective and goals that guided the project, as well as demonstrating potential benefits that could be obtained by applying the WUOT in different geo-hydrologic systems across the United States. A major challenge facing conventional hydropower plants is to operate more efficiently while dealing with an increasingly uncertain water-constrained environment and complex electricity markets. The goal of this 3-year WUOT project, which is funded by the U.S. Department of Energy (DOE), is to improve water management, resulting in more energy, revenues, and grid services from available water, and to enhance environmental benefits from improved hydropower operations and planning while maintaining institutional water delivery requirements. The long-term goal is for the WUOT to be used by environmental analysts and deployed by hydropower schedulers and operators to assist in market, dispatch, and operational decisions.

Demonstration of automated proximity and docking technologies

Science.gov (United States)

Anderson, Robert L.; Tsugawa, Roy K.; Bryan, Thomas C.

An autodock was demonstrated using straightforward techniques and real sensor hardware. A simulation testbed was established and validated. The sensor design was refined with improved optical performance and image processing noise mitigation techniques, and the sensor is ready for production from off-the-shelf components. The autonomous spacecraft architecture is defined. The areas of sensors, docking hardware, propulsion, and avionics are included in the design. The Guidance Navigation and Control architecture and requirements are developed. Modular structures suitable for automated control are used. The spacecraft system manager functions including configuration, resource, and redundancy management are defined. The requirements for autonomous spacecraft executive are defined. High level decisionmaking, mission planning, and mission contingency recovery are a part of this. The next step is to do flight demonstrations. After the presentation the following question was asked. How do you define validation? There are two components to validation definition: software simulation with formal and vigorous validation, and hardware and facility performance validated with respect to software already validated against analytical profile.

A SPECT demonstrator-revival of a gamma camera

International Nuclear Information System (INIS)

Valastyan, I.; Kerek, A.; Molnar, J.; Novak, D.; Vegh, J.; Emri, M.; Tron, L.

2006-01-01

A gamma camera has been updated and converted to serve as a demonstrator for educational purposes. The gantry and the camera head were the only part of the system that remained untouched. The main reason for this modernization was to increase the transparency of the gamma camera by partitioning the different logical building blocks of the system and thus providing access for inspection and improvements throughout the chain. New data acquisition and reconstruction software has been installed. By taking these measures, the camera is now used in education and also serves as a platform for tests of new hardware and software solutions. The camera is also used to demonstrate 3D (SPECT) imaging by collecting 2D projections from a rotatable cylindrical phantom. Since the camera head is not attached mechanically to the phantom, the effect of misalignment between the head and the rotation axis of the phantom can be studied

Airspace Technology Demonstration 2 (ATD-2) Phase 1 Concept of Use (ConUse)

Science.gov (United States)

Jung, Yoon; Engelland, Shawn; Capps, Richard; Coppenbarger, Rich; Hooey, Becky; Sharma, Shivanjli; Stevens, Lindsay; Verma, Savita; Lohr, Gary; Chevalley, Eric;

Conceptual design of the JAERI demonstration fusion reactor

International Nuclear Information System (INIS)

Sako, K.; Tone, T.; Seki, Y.

1976-01-01

Conceptual design of a tokamak demonstration fusion reactor is carried out. This design is an extended and improved version of the previous design which was presented at the 5th IAEA Conference. The main design parameters are as follows: the reactor thermal power 2000 MW, torus radius 10.5 m, plasma radius 2.7 m, first wall radius 3.0 m, toroidal magnetic field on axis 6T, blanket fertile material Li 2 O, coolant He, structural material Mo-alloy and tritium breeding ratio 1.2

Authoring Effective Demonstrations

National Research Council Canada - National Science Library

Fu, Dan; Jensen, Randy; Salas, Eduardo; Rosen, Michael A; Ramachandran, Sowmya; Upshaw, Christin L; Hinkelman, Elizabeth; Lampton, Don

2007-01-01

... or human role-players for each training event. We report our ongoing efforts to (1) research the nature and purpose of demonstration, articulating guidelines for effective demonstration within a training context, and (2...

A nationwide survey of patient centered medical home demonstration projects.

Science.gov (United States)

Bitton, Asaf; Martin, Carina; Landon, Bruce E

2010-06-01

The patient centered medical home has received considerable attention as a potential way to improve primary care quality and limit cost growth. Little information exists that systematically compares PCMH pilot projects across the country. Cross-sectional key-informant interviews. Leaders from existing PCMH demonstration projects with external payment reform. We used a semi-structured interview tool with the following domains: project history, organization and participants, practice requirements and selection process, medical home recognition, payment structure, practice transformation, and evaluation design. A total of 26 demonstrations in 18 states were interviewed. Current demonstrations include over 14,000 physicians caring for nearly 5 million patients. A majority of demonstrations are single payer, and most utilize a three component payment model (traditional fee for service, per person per month fixed payments, and bonus performance payments). The median incremental revenue per physician per year was $22,834 (range $720 to $91,146). Two major practice transformation models were identified--consultative and implementation of the chronic care model. A majority of demonstrations did not have well-developed evaluation plans. Current PCMH demonstration projects with external payment reform include large numbers of patients and physicians as well as a wide spectrum of implementation models. Key questions exist around the adequacy of current payment mechanisms and evaluation plans as public and policy interest in the PCMH model grows.

Strategy Guideline: Demonstration Home

Energy Technology Data Exchange (ETDEWEB)

Savage, C.; Hunt, A.

2012-12-01

This guideline will provide a general overview of the different kinds of demonstration home projects, a basic understanding of the different roles and responsibilities involved in the successful completion of a demonstration home, and an introduction into some of the lessons learned from actual demonstration home projects. Also, this guideline will specifically look at the communication methods employed during demonstration home projects. And lastly, we will focus on how to best create a communication plan for including an energy efficient message in a demonstration home project and carry that message to successful completion.

Strategy Guideline. Demonstration Home

Energy Technology Data Exchange (ETDEWEB)

Hunt, A.; Savage, C.

2012-12-01

This guideline will provide a general overview of the different kinds of demonstration home projects, a basic understanding of the different roles and responsibilities involved in the successful completion of a demonstration home, and an introduction into some of the lessons learned from actual demonstration home projects. Also, this guideline will specifically look at the communication methods employed during demonstration home projects. And lastly, we will focus on how to best create a communication plan for including an energy efficient message in a demonstration home project and carry that message to successful completion.

Evaluation and demonstration of methods for improved fuel utilization. Third semi-annual progress report, October 1, 1980-March 31, 1981

International Nuclear Information System (INIS)

1981-06-01

The demonstrations are being performed in the Fort Calhoun reactor. The current program consists of two parts, one to demonstrate low leakage fuel management (SAVFUEL - Shimmed And Very Flexible Uranium Element Loading) and the other to demonstrate high burnup. During this period the four SAVFUEL demonstration assemblies were undergoing their second exposure cycle, simulating the SAVFUEL power cycle. In addition, one high burnup demonstration assembly, which is being irradiated for a fifth exposure cycle has achieved a peak rod average burnup of 45 GWD/T which is the burnup originally targeted for this program. This assembly is projected to achieve a peak rod average burnup of 49 GWD/T at the end of its fifth exposure cycle. During this period analyses were performed to determine the sensitivity of the economics to cycle lengths chosen for Fort Calhoun. Cost savings for 18 month cycles relative to 12 month cycles are reported

Improvement of the polarized neutron interferometer setup demonstrating violation of a Bell-like inequality

Energy Technology Data Exchange (ETDEWEB)

Geppert, H., E-mail: hgeppert@ati.ac.at [Atominstitut, Vienna University of Technology, Stadionallee 2, 1020 Vienna (Austria); Denkmayr, T.; Sponar, S. [Atominstitut, Vienna University of Technology, Stadionallee 2, 1020 Vienna (Austria); Lemmel, H. [Atominstitut, Vienna University of Technology, Stadionallee 2, 1020 Vienna (Austria); Institut Laue Langevin, 38000 Grenoble (France); Hasegawa, Y. [Atominstitut, Vienna University of Technology, Stadionallee 2, 1020 Vienna (Austria)

2014-11-01

For precise measurements with polarised neutrons high efficient spin-manipulation is required. We developed several neutron optical elements suitable for a new sophisticated setup, i.e., DC spin-turners and Larmor-accelerators which diminish thermal disturbances and depolarisation considerably. The gain in performance is exploited demonstrating violation of a Bell-like inequality for a spin-path entangled single-neutron state. The obtained value of S=2.365(13), which is much higher than previous measurements by neutron interferometry, is 28σ above the limit of S=2 predicted by contextual hidden variable theories. The new setup is more flexible referring to state preparation and analysis, therefore new, more precise measurements can be carried out.

Improvement of the polarized neutron interferometer setup demonstrating violation of a Bell-like inequality.

Science.gov (United States)

Geppert, H; Denkmayr, T; Sponar, S; Lemmel, H; Hasegawa, Y

2014-11-01

For precise measurements with polarised neutrons high efficient spin-manipulation is required. We developed several neutron optical elements suitable for a new sophisticated setup, i.e., DC spin-turners and Larmor-accelerators which diminish thermal disturbances and depolarisation considerably. The gain in performance is exploited demonstrating violation of a Bell-like inequality for a spin-path entangled single-neutron state. The obtained value of [Formula: see text], which is much higher than previous measurements by neutron interferometry, is [Formula: see text] above the limit of S =2 predicted by contextual hidden variable theories. The new setup is more flexible referring to state preparation and analysis, therefore new, more precise measurements can be carried out.

Teaching quality improvement.

Science.gov (United States)

Murray, Marry Ellen; Douglas, Stephen; Girdley, Diana; Jarzemsky, Paula

2010-08-01

Practicing nurses are required to engage in quality improvement work as a part of their clinical practice, but few undergraduate nursing education programs offer course work and applied experience in this area. This article presents a description of class content and teaching strategies, assignments, and evaluation strategies designed to achieve the Quality and Safety Education in Nursing competencies related to quality improvement and interdisciplinary teams. Students demonstrate their application of the quality improvement process by designing and implementing a small-scale quality improvement project that they report in storyboard format on a virtual conference Web site.

Pacific Northwest Smart Grid Demonstration Project Technology Performance Report Volume 1: Technology Performance

Energy Technology Data Exchange (ETDEWEB)

Melton, Ron [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-06-01

The Pacific Northwest Smart Grid Demonstration (PNWSGD), a $179 million project that was co-funded by the U.S. Department of Energy (DOE) in late 2009, was one of the largest and most comprehensive demonstrations of electricity grid modernization ever completed. The project was one of 16 regional smart grid demonstrations funded by the American Recovery and Reinvestment Act. It was the only demonstration that included multiple states and cooperation from multiple electric utilities, including rural electric co-ops, investor-owned, municipal, and other public utilities. No fewer than 55 unique instantiations of distinct smart grid systems were demonstrated at the projects’ sites. The local objectives for these systems included improved reliability, energy conservation, improved efficiency, and demand responsiveness. The demonstration developed and deployed an innovative transactive system, unique in the world, that coordinated many of the project’s distributed energy resources and demand-responsive components. With the transactive system, additional regional objectives were also addressed, including the mitigation of renewable energy intermittency and the flattening of system load. Using the transactive system, the project coordinated a regional response across the 11 utilities. This region-wide connection from the transmission system down to individual premises equipment was one of the major successes of the project. The project showed that this can be done and assets at the end points can respond dynamically on a wide scale. In principle, a transactive system of this type might eventually help coordinate electricity supply, transmission, distribution, and end uses by distributing mostly automated control responsibilities among the many distributed smart grid domain members and their smart devices.

Recovery Act - Demonstration of Sodium Ion Battery for Grid Level Applications

Energy Technology Data Exchange (ETDEWEB)

Wiley, Ted [Aquion Energy, Inc., Pittsburgh, PA (United States); Whitacre, Jay [Aquion Energy, Inc., Pittsburgh, PA (United States); Weber, Eric [Aquion Energy, Inc., Pittsburgh, PA (United States); Eshoo, Michael [Aquion Energy, Inc., Pittsburgh, PA (United States); Noland, James [Aquion Energy, Inc., Pittsburgh, PA (United States); Blackwood, David [Aquion Energy, Inc., Pittsburgh, PA (United States); Campbell, Williams [Aquion Energy, Inc., Pittsburgh, PA (United States); Sheen, Eric [Aquion Energy, Inc., Pittsburgh, PA (United States); Spears, Christopher [Aquion Energy, Inc., Pittsburgh, PA (United States); Smith, Christopher [Aquion Energy, Inc., Pittsburgh, PA (United States)

2012-08-31

Aquion Energy received a $5.179 million cooperative research agreement under the Department of Energy's Smart Grid Demonstration Program Demonstration of Promising Energy Storage Technologies (Program Area 2.5) of FOA DE-FOE-0000036. The main objective of this project was to demonstrate Aquion's low cost, grid-scale, ambient temperature sodium ion energy storage device. The centerpiece of the technology is a novel hybrid energy storage chemistry that has been proven in a laboratory environment. The objective was to translate these groundbreaking results from the small-batch, small-cell test environment to the pilot scale to enable significant numbers of multiple ampere-hour cells to be manufactured and assembled into test batteries. Aquion developed a proof of concept demonstration unit that showed similar performance and major cost improvement over existing technologies. Beyond minimizing cell and system cost, Aquion built a technology that is safe, environmentally benign and durable over many thousands of cycles as used in a variety of grid support roles.

Business process modeling for the Virginia Department of Transportation : a demonstration with the integrated six-year improvement program and the statewide transportation improvement program.

Science.gov (United States)

2005-01-01

This effort demonstrates business process modeling to describe the integration of particular planning and programming activities of a state highway agency. The motivations to document planning and programming activities are that: (i) resources for co...

Oxygenated fixation demonstrates novel and improved ultrastructural features of the human endolymphatic sac

DEFF Research Database (Denmark)

Møller, Martin Nue; Caye-Thomasen, Per; Qvortrup, Klaus

2013-01-01

OBJECTIVES/HYPOTHESIS: The purpose of the present study is to describe in detail the ultrastructure of the human endolymphatic sac using a new and improved method of fixation as well as a refined surgical approach in obtaining specimens. STUDY DESIGN: Transmission electron microscopy of the human...... epithelial cell lining in all 18 specimens. In general, we found very well-preserved specimens with well-defined intracellular structures. In contrast to the results in former studies, a minimum of fixation artifacts was observed in the present study. Three different cell types were observed...... endolymphatic sac, employing an oxygenated fixative. METHODS: Eighteen tissue samples of the human endolymphatic sac were obtained during surgery for vestibular schwannoma using the translabyrinthine approach. The specimens were fixed in 2% glutaraldehyde in an oxygenated fluorocarbon blood substitute vehicle...

Automated Student Model Improvement

Science.gov (United States)

Koedinger, Kenneth R.; McLaughlin, Elizabeth A.; Stamper, John C.

2012-01-01

Student modeling plays a critical role in developing and improving instruction and instructional technologies. We present a technique for automated improvement of student models that leverages the DataShop repository, crowd sourcing, and a version of the Learning Factors Analysis algorithm. We demonstrate this method on eleven educational…

Navy fuel cell demonstration project.

Energy Technology Data Exchange (ETDEWEB)

Black, Billy D.; Akhil, Abbas Ali

2008-08-01

This is the final report on a field evaluation by the Department of the Navy of twenty 5-kW PEM fuel cells carried out during 2004 and 2005 at five Navy sites located in New York, California, and Hawaii. The key objective of the effort was to obtain an engineering assessment of their military applications. Particular issues of interest were fuel cell cost, performance, reliability, and the readiness of commercial fuel cells for use as a standalone (grid-independent) power option. Two corollary objectives of the demonstration were to promote technological advances and to improve fuel performance and reliability. From a cost perspective, the capital cost of PEM fuel cells at this stage of their development is high compared to other power generation technologies. Sandia National Laboratories technical recommendation to the Navy is to remain involved in evaluating successive generations of this technology, particularly in locations with greater environmental extremes, and it encourages their increased use by the Navy.

Enhancing the prospects for palliative care at the end of life: A statewide educational demonstration project to improve advance care planning.

Science.gov (United States)

Litzelman, Debra K; Cottingham, Ann H; Griffin, Wilma; Inui, Thomas S; Ivy, Steven S

2016-12-01

Although patients want to participate in discussions and decisions about their end-of-life care, studies show that providers frequently fail to invite them to explore advanced care preferences or goals for living. The purpose of our demonstration project was to provide education and coaching to individuals, health providers, and organizations across the state of Indiana intended to facilitate these conversations, documenting and honoring individuals' life goals and preferences for care during the final stages of life. Education and training engaged community members as well as healthcare providers to: (1) improve participant comfort and facility discussing end-of-life issues; (2) improve knowledge of healthcare choices, including palliative and hospice care; and (3) prepare all participants to explore and document personal values, life goals, and priorities as well as goals of care. Between January of 2013 and June of 2015, the team educated close to 5,000 participants. Participants' ratings of the quality and perceived usefulness of the educational events ranged from 4 to 5 (using a 5-point scale, with 5 = most effective). Participant comments were overwhelmingly favorable and indicated an intention to put the advance care planning resources, communication skills, knowledge of palliative and hospice care, and personal renewal techniques into practice. Participant motivation to foster advance care planning, discussions of palliative care, and end-of-life conversations was facilitated by the reframing of these conversations as identifying goals of care and priorities for living well during an important stage of life. Successful strategies included helping providers and patients to adopt a broader meaning for "sustaining hope" (not for cure, but for engaging in highly valued activities), developing provider communication skills and comfort in initiating potentially difficult discussions, engaging a new community health workforce who will develop trusting

Osteochondral Biopsy Analysis Demonstrates That BST-CarGel Treatment Improves Structural and Cellular Characteristics of Cartilage Repair Tissue Compared With Microfracture

Science.gov (United States)

Méthot, Stéphane; Changoor, Adele; Tran-Khanh, Nicolas; Hoemann, Caroline D.; Stanish, William D.; Restrepo, Alberto; Shive, Matthew S.; Buschmann, Michael D.

2016-01-01

Objective The efficacy and safety of BST-CarGel, a chitosan-based medical device for cartilage repair, was compared with microfracture alone at 1 year during a multicenter randomized controlled trial (RCT) in the knee. The quality of repair tissue of osteochondral biopsies collected from a subset of patients was compared using blinded histological assessments. Methods The international RCT evaluated repair tissue quantity and quality by 3-dimensional quantitative magnetic resonance imaging as co-primary endpoints at 12 months. At an average of 13 months posttreatment, 21/41 BST-CarGel and 17/39 microfracture patients underwent elective second look arthroscopies as a tertiary endpoint, during which ICRS (International Cartilage Repair Society) macroscopic scoring was carried out, and osteochondral biopsies were collected. Stained histological sections were evaluated by blinded readers using ICRS I and II histological scoring systems. Collagen organization was evaluated using a polarized light microscopy score. Results BST-CarGel treatment resulted in significantly better ICRS macroscopic scores (P = 0.0002) compared with microfracture alone, indicating better filling, integration, and tissue appearance. Histologically, BST-CarGel resulted in a significant improvement of structural parameters—Surface Architecture (P = 0.007) and Surface/Superficial Assessment (P = 0.042)—as well as cellular parameters—Cell Viability (P = 0.006) and Cell Distribution (P = 0.032). No histological parameters were significantly better for the microfracture group. BST-CarGel treatment also resulted in a more organized repair tissue with collagen stratification more similar to native hyaline cartilage, as measured by polarized light microscopy scoring (P = 0.0003). Conclusion Multiple and independent analyses in this biopsy substudy demonstrated that BST-CarGel treatment results in improved structural and cellular characteristics of repair tissue at 1 year posttreatment compared with

SPECT Perfusion Imaging Demonstrates Improvement of Traumatic Brain Injury With Transcranial Near-infrared Laser Phototherapy.

Science.gov (United States)

Henderson, Theodore A; Morries, Larry D

2015-01-01

Traumatic brain injury (TBI) is a growing health concern affecting civilians and military personnel. Near-infrared (NIR) light has shown benefits in animal models and human trials for stroke and in animal models for TBI. Diodes emitting low-level NIR often have lacked therapeutic efficacy, perhaps failing to deliver sufficient radiant energy to the necessary depth. In this case report, a patient with moderate TBI documented in anatomical magnetic resonance imaging (MRI) and perfusion single-photon emission computed tomography (SPECT) received 20 NIR treatments in the course of 2 mo using a high-power NIR laser. Symptoms were monitored by clinical examination and a novel patient diary system specifically designed for this patient population. Clinical application of these levels of infrared energy for this patient with TBI yielded highly favorable outcomes with decreased depression, anxiety, headache, and insomnia, whereas cognition and quality of life improved. Neurological function appeared to improve based on changes in the SPECT by quantitative analysis. NIR in the power range of 10-15 W at 810 and 980 nm can safely and effectively treat chronic symptoms of TBI.

Innovative technology demonstration

International Nuclear Information System (INIS)

Anderson, D.B.; Luttrell, S.P.; Hartley, J.N.; Hinchee, R.

1992-04-01

The Innovative Technology Demonstration (ITD) program at Tinker Air Force Base (TAFB), Oklahoma City, Oklahoma, will demonstrate the overall utility and effectiveness of innovative technologies for site characterization, monitoring, and remediation of selected contaminated test sites. The current demonstration test sites include a CERCLA site on the NPL list, located under a building (Building 3001) that houses a large active industrial complex used for rebuilding military aircraft, and a site beneath and surrounding an abandoned underground tank vault used for storage of jet fuels and solvents. The site under Building 3001 (the NW Test Site) is contaminated with TCE and Cr +6 ; the site with the fuel storage vault (the SW Tanks Site) is contaminated with fuels, BTEX and TCE. These sites and others have been identified for cleanup under the Air Force's Installation Restoration Program (IRP). This document describes the demonstrations that have been conducted or are planned for the TAFB

Low Temperature Combustion Demonstrator for High Efficiency Clean Combustion

Energy Technology Data Exchange (ETDEWEB)

Ojeda, William de

2010-07-31

The project which extended from November 2005 to May of 2010 demonstrated the application of Low Temperature Combustion (LTC) with engine out NOx levels of 0.2 g/bhp-hr throughout the program target load of 12.6bar BMEP. The project showed that the range of loads could be extended to 16.5bar BMEP, therefore matching the reference lug line of the base 2007 MY Navistar 6.4L V8 engine. Results showed that the application of LTC provided a dramatic improvement over engine out emissions when compared to the base engine. Furthermore LTC improved thermal efficiency by over 5% from the base production engine when using the steady state 13 mode composite test as a benchmark. The key enablers included improvements in the air, fuel injection, and cooling systems made in Phases I and II. The outcome was the product of a careful integration of each component under an intelligent control system. The engine hardware provided the conditions to support LTC and the controller provided the necessary robustness for a stable combustion. Phase III provided a detailed account on the injection strategy used to meet the high load requirements. During this phase, the control strategy was implemented in a production automotive grade ECU to perform cycle-by-cycle combustion feedback on each of the engine cylinders. The control interacted on a cycle base with the injection system and with the Turbo-EGR systems according to their respective time constants. The result was a unique system that could, first, help optimize the combustion system and maintain high efficiency, and secondly, extend the steady state results to the transient mode of operation. The engine was upgraded in Phase IV with a Variable Valve Actuation system and a hybrid EGR loop. The impact of the more versatile EGR loop did not provide significant advantages, however the application of VVA proved to be an enabler to further extend the operation of LTC and gain considerable benefits in fuel economy and soot reduction. Finally

Evaluation of waste treatment technologies by LLWDDD [Low-Level Waste Disposal Development and Demonstration] Programs

International Nuclear Information System (INIS)

Kennerly, J.M.; Williams, L.C.; Dole, L.R.; Genung, R.K.

1987-01-01

Waste treatments are divided into four categories: (1) volume reduction; (2) conditioning to improve waste form performance; (3) segregation to achieve waste reduction; and (4) separation to remove radioactive (or hazardous) constituents. Two waste treatment demonstrations are described. In the first, volume reduction by mechanical means was achieved during the supercompaction of 300 55-gal drums of solid waste at ORNL. In the second demonstration, conditioning of waste through immobilization and packaging to improve the performance of the waste form is being evaluated. The final section of this paper describes potential scenarios for the management of uranium-contaminated wastes at the Y-12 Plant in Oak Ridge and emphasizes where demonstrations of treatment technology will be needed to implement the scenarios. Separation and thermal treatment are identified as the principal means for treating these wastes. 15 figs

Integrating empowerment evaluation and quality improvement to achieve healthcare improvement outcomes

Science.gov (United States)

Wandersman, Abraham; Alia, Kassandra Ann; Cook, Brittany; Ramaswamy, Rohit

2015-01-01

While the body of evidence-based healthcare interventions grows, the ability of health systems to deliver these interventions effectively and efficiently lags behind. Quality improvement approaches, such as the model for improvement, have demonstrated some success in healthcare but their impact has been lessened by implementation challenges. To help address these challenges, we describe the empowerment evaluation approach that has been developed by programme evaluators and a method for its application (Getting To Outcomes (GTO)). We then describe how GTO can be used to implement healthcare interventions. An illustrative healthcare quality improvement example that compares the model for improvement and the GTO method for reducing hospital admissions through improved diabetes care is described. We conclude with suggestions for integrating GTO and the model for improvement. PMID:26178332

Innovative technology demonstrations

International Nuclear Information System (INIS)

Anderson, D.B.; Luttrell, S.P.; Hartley, J.N.

1992-08-01

Environmental Management Operations (EMO) is conducting an Innovative Technology Demonstration Program for Tinker Air Force Base (TAFB). Several innovative technologies are being demonstrated to address specific problems associated with remediating two contaminated test sites at the base. Cone penetrometer testing (CPT) is a form of testing that can rapidly characterize a site. This technology was selected to evaluate its applicability in the tight clay soils and consolidated sandstone sediments found at TAFB. Directionally drilled horizontal wells was selected as a method that may be effective in accessing contamination beneath Building 3001 without disrupting the mission of the building, and in enhancing the extraction of contamination both in ground water and in soil. A soil gas extraction (SGE) demonstration, also known as soil vapor extraction, will evaluate the effectiveness of SGE in remediating fuels and TCE contamination contained in the tight clay soil formations surrounding the abandoned underground fuel storage vault located at the SW Tanks Site. In situ sensors have recently received much acclaim as a technology that can be effective in remediating hazardous waste sites. Sensors can be useful for determining real-time, in situ contaminant concentrations during the remediation process for performance monitoring and in providing feedback for controlling the remediation process. Following the SGE demonstration, the SGE system and SW Tanks test site will be modified to demonstrate bioremediation as an effective means of degrading the remaining contaminants in situ. The bioremediation demonstration will evaluate a bioventing process in which the naturally occurring consortium of soil bacteria will be stimulated to aerobically degrade soil contaminants, including fuel and TCE, in situ

75 FR 55109 - Science and Technology Reinvention Laboratory Personnel Management Demonstration Project...

Science.gov (United States)

2010-09-09

.... Satisfaction of customers; and 7. Workforce satisfaction with the personnel management system. An evaluation... personnel system under an appropriate demonstration project as defined in section 342(b) of Public Law 103... for the TARDEC mission, adjust the workforce for change, and improve workforce satisfaction. The...

Demonstration irradiation of CANFLEX in Pt. Lepreau

International Nuclear Information System (INIS)

Inch, W.; Thompson, P.; Suk, Ho Chun

1999-01-01

The demonstration irradiation of CANFLEX in the Point Lepreau Generating Station (PLGS) in New Brunswick, Canada, will mark a major milestone towards delivering this new fuel to CANDU utilities. One high-powered and one instrumented fuel channel are being fuelled with CANFLEX bundles to establish irradiation experience in a power reactor. As CANFLEX is discharged into the reactor bays, it win be examined by fuel experts from PLGS and AECL. Several irradiated CANFLEX bundles will be shipped to Chalk River for extensive post-irradiation examination. CANFLEX is the latest fuel carrier in the evolution of CANDU fuel. Its design has been driven to provide higher dryout powers and lower peak element ratings, while being fully compatible with existing CANDU stations and addressing the development requirements for future advanced CANDU stations. The design has been tuned through analysis and testing at AECL and KAERI. The final CANFLEX design has undergone extensive analysis, performance testing and critical industry review. Safety performance has been analyzed and documented in a licensing submission to the Canadian regulator, the Atomic Energy Control Board, for approval to proceed with the demonstration irradiation. Because CANFLEX is fully compatible with existing plants, CANDU 6 stations can simply substitute CANFLEX-NU for 37-element fuel and achieve improved reactor operating and safety margins, and higher critical channel powers. For CANDU designers, CANFLEX provides the opportunity to benefit from the use of slightly enriched uranium (SEU) or recycled uranium (RU) from reprocessed spent PWR fuel. Enrichment can be used in one of several ways: to increase the power from a given reactor core size through flattening the radial channel power profile; to increase the fuel burnup and reduce the quantity of spent fuel; to improve fuel cycle economics, both front- and back-end; and, in general, to provide greater flexibility in reactor design. (author)

Demonstration of risk-based approaches to nuclear plant regulation

International Nuclear Information System (INIS)

Rahn, F.J.; Sursock, J.P.; Darling, S.S.; Oddo, J.M.

1993-01-01

This paper describes generic technical support EPRI is providing to the nuclear power industry relative to its recent initiatives in the area of risk-based regulations (RBR). A risk-based regulatory approach uses probabilistic risk assessment (PRA), or similar techniques, to allocate safety resources commensurate with the risk posed by nuclear plant operations. This approach will reduce O ampersand M costs, and also improve nuclear plant safety. In order to enhance industry, Nuclear Regulatory Commission (NRC) and public confidence in RBR, three things need to be shown: (1) manpower/resource savings are significant for both NRC and industry; (2) the process is doable in a reasonable amount of time; and (3) the process, if uniformly applied, results in demonstrably cheaper power and safer plants. In 1992, EPRI performed a qualitative study of the key RBR issues contributing to high O ampersand M costs. The results are given on Table 1. This study is being followed up by an in-depth quantitative cost/benefit study to focus technical work on producing guidelines/procedures for licensing submittals to NRC. The guidelines/procedures necessarily will be developed from successful demonstration projects such as the Fitzpatrick pilot plant study proposed by the New York Power Authority and other generic applications. This paper presents three examples: two motor operated valve projects performed by QUADREX Energy Services Corporation working with utilities in responding to NRC Generic Letter 89-10, and a third project working with Yankee Atomic Electric Company on service water systems at a plant in its service system. These demonstration projects aim to show the following: (1) the relative ease of putting together a technical case based on RBR concepts; (2) clarity in differentiating the various risk trade-offs, and in communicating overall reductions in risk with NRC; and (3) improved prioritization of NRC directives

``Wow'' is good, but ``I see'' is better - techniques for more effective Physics demonstrations

Science.gov (United States)

Collins, Stephen

2008-03-01

The use of demonstrations to assist in Physics education at all levels is commonplace, but frequently lacks optimal effectiveness. In many cases, the choice of demonstration is not at issue, but rather the manner in which it is presented to the audience. Modern educational research reveals a number of simple ways to improve instruction of this kind, including objective setting, audience evaluation, concept building, and promoting engagement. These techniques and considerations will be reviewed, explained, and modeled through a demonstration of ``Why Mr. Fork and Mr. Microwave Oven don't get along.''

Combining expedited cleanup with innovative technology demonstrations

International Nuclear Information System (INIS)

Hagood, M.C.; Rohay, V.J.; Valcich, P.J.; Brouns, T.M.; Cameron, R.J.

1993-04-01

A Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) expedited response action (ERA) has been initiated at the Hanford Site, Washington, for the removal of carbon tetrachloride from contaminated soils to mitigate further contamination of the groundwater. Soil vapor extraction with aboveground collection and treatment was chosen as the preferred remedial technology for the first phase of the ERA. At the same time, innovative technology demonstrations are being conducted in coordination with the ERA to determine the viability of emerging technologies that can be used to characterize, remediate, and monitor carbon tetrachloride and cocontaminants. The overall goal is to improve the performance and decrease the costs of carbon tetrachloride remediation while maintaining a safe working environment

Innovative technology demonstrations

International Nuclear Information System (INIS)

Anderson, D.B.; Hartley, J.N.; Luttrell, S.P.

1992-04-01

Currently, several innovative technologies are being demonstrated at Tinker Air Force Base (TAFB) to address specific problems associated with remediating two contaminated test sites at the base. Cone penetrometer testing (CPT) is a form of testing that can rapidly characterize a site. This technology was selected to evaluate its applicability in the tight clay soils and consolidated sandstone sediments found at TAFB. Directionally drilled horizontal wells have been successfully installed at the US Department of Energy's (DOE) Savannah River Site to test new methods of in situ remediation of soils and ground water. This emerging technology was selected as a method that may be effective in accessing contamination beneath Building 3001 without disrupting the mission of the building, and in enhancing the extraction of contamination both in ground water and in soil. A soil gas extraction (SGE) demonstration, also known as soil vapor extraction, will evaluate the effectiveness of SGE in remediating fuels and TCE contamination contained in the tight clay soil formations surrounding the abandoned underground fuel storage vault located at the SW Tanks Site. In situ sensors have recently received much acclaim as a technology that can be effective in remediating hazardous waste sites. Sensors can be useful for determining real-time, in situ contaminant concentrations during the remediation process for performance monitoring and in providing feedback for controlling the remediation process. A demonstration of two in situ sensor systems capable of providing real-time data on contamination levels will be conducted and evaluated concurrently with the SGE demonstration activities. Following the SGE demonstration, the SGE system and SW Tanks test site will be modified to demonstrate bioremediation as an effective means of degrading the remaining contaminants in situ

JOYO modification program for demonstration tests of FBR innovative technology development

International Nuclear Information System (INIS)

Yoshimi, H.; Hachiya, Y.

1990-01-01

A plan is under way at PNC to modify the experimental fast reactor JOYO. The project is called MARK-III (MK-III) program. The purpose of MK-III is to expand the function of JOYO, and to make it possible to receive demonstration tests of new or high level technologies for FBR development. The MK-III program consists of two main modifications: conversion to a highly efficient irradiation facility; and a modification for demonstration testing of new technologies and concepts that have a high potential to reduce FBR plant construction cost, to evaluate plant reliability and to improve plant safety. These modifications are scheduled to start in 1991

Radioactive waste incineration system cold demonstration test, (2)

Energy Technology Data Exchange (ETDEWEB)

Hozumi, Masahiro; Seike, Yasuhiko; Takaoku, Yoshinobu; Yamanaka, Yasuhiro; Asahara, Masaharu; Katagiri, Keishi; Matsumoto, Kenji; Nagae, Madoka

1985-12-01

It is urgently necessary to solve the radioactive waste problem. As an effective means for the volume reduction of low-level radioactive wastes, an improved incineration system is greatly required. SHI's Waste Incineration (WIS) licensed by Combustion Engineering, Inc., has the significant advantage of processing a variety of wastes. We started a cold demonstration test in April, 1984 to verify the excellent performance of WIS. The test was successfully completed in September, 1985 with the record of more than 1000 hours of incineration testing time. In the present paper, we describe the test results during one and half years of test period.

The End-to-end Demonstrator for improved decision making in the water sector in Europe (EDgE)

Science.gov (United States)

Wood, Eric; Wanders, Niko; Pan, Ming; Sheffield, Justin; Samaniego, Luis; Thober, Stephan; Kumar, Rohinni; Prudhomme, Christel; Houghton-Carr, Helen

2017-04-01

High-resolution simulations of water resources from hydrological models are vital to supporting important climate services. Apart from a high level of detail, both spatially and temporally, it is important to provide simulations that consistently cover a range of timescales, from historical reanalysis to seasonal forecast and future projections. In the new EDgE project commissioned by the ECMWF (C3S) we try to fulfill these requirements. EDgE is a proof-of-concept project which combines climate data and state-of-the-art hydrological modelling to demonstrate a water-oriented information system implemented through a web application. EDgE is working with key European stakeholders representative of private and public sectors to jointly develop and tailor approaches and techniques. With these tools, stakeholders are assisted in using improved climate information in decision-making, and supported in the development of climate change adaptation and mitigation policies. Here, we present the first results of the EDgE modelling chain, which is divided into three main processes: 1) pre-processing and downscaling; 2) hydrological modelling; 3) post-processing. Consistent downscaling and bias corrections for historical simulations, seasonal forecasts and climate projections ensure that the results across scales are robust. The daily temporal resolution and 5km spatial resolution ensure locally relevant simulations. With the use of four hydrological models (PCR-GLOBWB, VIC, mHM, Noah-MP), uncertainty between models is properly addressed, while consistency is guaranteed by using identical input data for static land surface parameterizations. The forecast results are communicated to stakeholders via Sectoral Climate Impact Indicators (SCIIs) that have been created in collaboration with the end-user community of the EDgE project. The final product of this project is composed of 15 years of seasonal forecast and 10 climate change projections, all combined with four hydrological

Commercial-Scale Demonstration of the Liquid Phase Methanol (LPMEOTH) Process

Energy Technology Data Exchange (ETDEWEB)

None

1998-12-21

The Liquid Phase Methanol (LPMEOW) Demonstration Project at Kingsport, Tennessee, is a $213.7 million cooperative agreement between the U.S. Department of Energy (DOE) and Air Products Liquid Phase Conversion Company, L.P. (the Partnership) to produce methanol from coal-derived synthesis gas (syngas). Air Products and Chemicals, Inc. (Air Products) and Eastman Chemical Company (Eastman) formed the Partnership to execute the Demonstration Project. The LPMEOI-P Process Demonstration Unit was built at a site located at the Eastman coal-to-chemicals complex in Kingsport. During this quarter, initial planning and procurement work continued on the seven project sites which have been accepted for participation in the off-site, product-use test program. Approximately 12,000 gallons of fuel-grade methanol (98+ wt% methanol, 4 wt% water) produced during operation on carbon monoxide (CO)-rich syngas at the LPMEOW Demonstration Unit was loaded into trailers and shipped off-site for Mure product-use testing. At one of the projects, three buses have been tested on chemical-grade methanol and on fhel-grade methanol from the LPMEOW Demonstration Project. During the reporting period, planning for a proof-of-concept test run of the Liquid Phase Dimethyl Ether (LPDME~ Process at the Alternative Fuels Development Unit (AFDU) in LaPorte, TX continued. The commercial catalyst manufacturer (Calsicat) has prepared the first batch of dehydration catalyst in large-scale equipment. Air Products will test a sample of this material in the laboratory autoclave. Catalyst activity, as defined by the ratio of the rate constant at any point in time to the rate constant for freshly reduced catalyst (as determined in the laborato~ autoclave), was monitored for the initial extended operation at the lower initial reactor operating temperature of 235oC. At this condition, the decrease in catalyst activity with time from the period 20 December 1997 through 27 January 1998 occurred at a rate of 1.0% per

Demonstration of Eastman Christensen horizontal drilling system -- Integrated Demonstration Site, Savannah River Site

International Nuclear Information System (INIS)

1992-12-01

An innovative horizontal drilling system was used to install two horizontal wells as part of an integrated demonstration project at the Savannah River Site (SRS), Aiken, South Carolina. The SRS is located in south-central South Carolina in the upper Coastal Plain physiographic province. The demonstration site is located near the A/M Area, and is currently known as the Integated Demonstration Site. The Department of Energy's Office of Technology Development initiated an integrated demonstration of innovative technologies for cleanup of volatile organic compounds (VOCS) in soils and groundwater at the SRS in 1989. The overall goal of the program is to demonstrate, at a single location, multiple technologies in the fields of drilling, characterization, monitoring, and remediation. Innovative technologies are compared to one another and to baseline technologies in terms of technical performance and cost effectiveness. Transfer of successfully demonstrated technologies and systems to DOE environmental restoration organizations, to other government agencies, and to industry is a critical part of the program

Southern Nevada Alternative Fuels Demonstration Project

Energy Technology Data Exchange (ETDEWEB)

Hyde, Dan; Fast, Matthew

2009-12-31

The Southern Nevada Alternative Fuels Program is designed to demonstrate, in a day-to-day bus operation, the reliability and efficiency of a hydrogen bus operation under extreme conditions. By using ICE technology and utilizing a virtually emission free fuel, benefits to be derived include air quality enhancement and vehicle performance improvements from domestically produced, renewable energy sources. The project objective is to help both Ford and the City demonstrate and evaluate the performance characteristics of the E-450 H2ICE shuttle buses developed by Ford, which use a 6.8-liter supercharged Triton V-10 engine with a hydrogen storage system equivalent to 29 gallons of gasoline. The technology used during the demonstration project in the Ford buses is a modified internal combustion engine that allows the vehicles to run on 100% hydrogen fuel. Hydrogen gives a more thorough fuel burn which results in more power and responsiveness and less pollution. The resultant emissions from the tailpipe are 2010 Phase II compliant with NO after treatment. The City will lease two of these E-450 H2ICE buses from Ford for two years. The buses are outfitted with additional equipment used to gather information needed for the evaluation. Performance, reliability, safety, efficiency, and rider comments data will be collected. The method of data collection will be both electronically and manually. Emissions readings were not obtained during the project. The City planned to measure the vehicle exhaust with an emissions analyzer machine but discovered the bus emission levels were below the capability of their machine. Passenger comments were solicited on the survey cards. The majority of comments were favorable. The controllable issues encountered during this demonstration project were mainly due to the size of the hydrogen fuel tanks at the site and the amount of fuel that could be dispensed during a specified period of time. The uncontrollable issues encountered during this

Electric vehicle demonstration

Energy Technology Data Exchange (ETDEWEB)

Ouellet, M. [National Centre for Advanced Transportation, Saint-Jerome, PQ (Canada)

2010-07-01

The desirable characteristics of Canadian projects that demonstrate vehicle use in real-world operation and the appropriate mechanism to collect and disseminate the monitoring data were discussed in this presentation. The scope of the project was on passenger cars and light duty trucks operating in plug-in electric vehicle (PHEV) or battery electric vehicle modes. The presentation also discussed the funding, stakeholders involved, Canadian travel pattern analysis, regulatory framework, current and recent electric vehicle demonstration projects, and project guidelines. It was concluded that some demonstration project activities may have been duplicated as communication between the proponents was insufficient. It was recommended that data monitoring using automatic data logging with minimum reliance on logbooks and other user entry should be emphasized. figs.

Improvement on a science curriculum including experimental demonstration of environmental radioactivity for secondary school students

International Nuclear Information System (INIS)

Watanabe, Kenji; Matsubara, Shizuo; Aiba, Yoshio; Eriguchi, Hiroshi; Kiyota, Saburo; Takeyama, Tetsuji.

1988-01-01

A science curriculum previously prepared for teaching environmental radioactivity was modified on the basis of the results of trial instructions in secondary schools. The main subject of the revised curriculum is an understanding of the natural radioactivity through the experimental demonstration about air-borne β and γ ray emitters. The other subjects included are the radioactive decay, the biological effects of radiation, the concept of risk-benefit balance (acceptable level) and the peaceful uses of nuclear energy and radiation. The work sheets and reference data prepared as learning materials are in two levels corresponding to the ability of students for this curriculum. (author)

Large-scale demonstration of D ampersand D technologies

International Nuclear Information System (INIS)

Bhattacharyya, S.K.; Black, D.B.; Rose, R.W.

1997-01-01

It is becoming increasingly evident that new technologies will need to be utilized for decontamination and decommissioning (D ampersand D) activities in order to assure safe and cost effective operations. The magnitude of the international D ampersand D problem is sufficiently large in anticipated cost (100's of billions of dollars) and in elapsed time (decades), that the utilization of new technologies should lead to substantial improvements in cost and safety performance. Adoption of new technologies in the generally highly contaminated D ampersand D environments requires assurances that the technology will perform as advertised. Such assurances can be obtained from demonstrations of the technology in environments that are similar to the actual environments without being quite as contaminated and hazardous. The Large Scale Demonstration Project (LSDP) concept was designed to provide such a function. The first LSDP funded by the U.S. Department Of Energy's Environmental Management Office (EM) was on the Chicago Pile 5 (CP-5) Reactor at Argonne National Laboratory. The project, conducted by a Strategic Alliance for Environmental Restoration, has completed demonstrations of 10 D ampersand D technologies and is in the process of comparing the performance to baseline technologies. At the conclusion of the project, a catalog of performance comparisons of these technologies will be developed that will be suitable for use by future D ampersand D planners

Demonstration test of the spent fuel rod cutting process with tube cutter mechanism

International Nuclear Information System (INIS)

Lee, Jong Youl; Jung, Jae Hoo; Hong, Dong Hee; Yoon, Ji Sup; Lee, Eun Pyo

2001-03-01

In this paper, the verification by computer graphics technology for the spent fuel rod cutting devise which belongs to the spent fuel disassembly processes, the performance tests of the real device, and the demonstration tests with tube cutter mechanism are described. The graphical design system is used throughout the design stages from conceptual design to motion analysis like collision detection. By using this system, the device and the process are optimized. The performance test of the real device and the demonstration test using the tube cutter mechanism in the hot cell are carried out. From these results, the spent fuel rod cutting device is improved based on the considerations of circularity of the rod cross-section, debris generation, and fire risk etc. Also, this device is improved to be operated automatically via remote control system considering later use in closed environment like Hot-cell (radioactive area) and the modulization in the structure of this device makes maintenance easy. The result of the performance test and the demonstration in this report is expected to contribute to the optimization of the pre-treatment processes for the reuse of the spent fuel like DUPIC process and the final disposal

Experimental demonstration of nonbinary LDPC convolutional codes for DP-64QAM/256QAM

NARCIS (Netherlands)

Koike-Akino, T.; Sugihara, K.; Millar, D.S.; Pajovic, M.; Matsumoto, W.; Alvarado, A.; Maher, R.; Lavery, D.; Paskov, M.; Kojima, K.; Parsons, K.; Thomsen, B.C.; Savory, S.J.; Bayvel, P.

2016-01-01

We show the great potential of nonbinary LDPC convolutional codes (NB-LDPC-CC) with low-latency windowed decoding. It is experimentally demonstrated that NB-LDPC-CC can offer a performance improvement of up to 5 dB compared with binary coding.

Demonstrating Heisenberg-limited unambiguous phase estimation without adaptive measurements

International Nuclear Information System (INIS)

Higgins, B L; Wiseman, H M; Pryde, G J; Berry, D W; Bartlett, S D; Mitchell, M W

2009-01-01

We derive, and experimentally demonstrate, an interferometric scheme for unambiguous phase estimation with precision scaling at the Heisenberg limit that does not require adaptive measurements. That is, with no prior knowledge of the phase, we can obtain an estimate of the phase with a standard deviation that is only a small constant factor larger than the minimum physically allowed value. Our scheme resolves the phase ambiguity that exists when multiple passes through a phase shift, or NOON states, are used to obtain improved phase resolution. Like a recently introduced adaptive technique (Higgins et al 2007 Nature 450 393), our experiment uses multiple applications of the phase shift on single photons. By not requiring adaptive measurements, but rather using a predetermined measurement sequence, the present scheme is both conceptually simpler and significantly easier to implement. Additionally, we demonstrate a simplified adaptive scheme that also surpasses the standard quantum limit for single passes.

Quality Improvement Initiatives in Inflammatory Bowel Disease.

Science.gov (United States)

Berry, Sameer K; Siegel, Corey A; Melmed, Gil Y

2017-08-01

This article serves as an overview of several quality improvement initiatives in inflammatory bowel disease (IBD). IBD is associated with significant variation in care, suggesting poor quality of care. There have been several efforts to improve the quality of care for patients with IBD. Quality improvement (QI) initiatives in IBD are intended to be patient-centric, improve outcomes for individuals and populations, and reduce costs-all consistent with "the triple aim" put forth by the Institute for Healthcare Improvement (IHI). Current QI initiatives include the development of quality measure sets to standardize processes and outcomes, learning health systems to foster collaborative improvement, and patient-centered medical homes specific to patients with IBD in shared risk models of care. Some of these programs have demonstrated early success in improving patient outcomes, reducing costs, improving patient satisfaction, and facilitating patient engagement. However, further studies are needed to evaluate and compare the effects of these programs over time on clinical outcomes in order to demonstrate long-term value and sustainability.

Learning From Demonstration?

DEFF Research Database (Denmark)

Koch, Christian; Bertelsen, Niels Haldor

2014-01-01

Demonstration projects are often used in the building sector to provide a basis for using new processes and/or products. The climate change agenda implies that construction is not only required to deliver value for the customer, cost reductions and efficiency but also sustainable buildings....... This paper reports on an early demonstration project, the Building of a passive house dormitory in the Central Region of Denmark in 2006-2009. The project was supposed to deliver value, lean design, prefabrication, quality in sustainability, certification according to German standards for passive houses......, and micro combined heat and power using hydrogen. Using sociological and business economic theories of innovation, the paper discusses how early movers of innovation tend to obtain only partial success when demonstrating their products and often feel obstructed by minor details. The empirical work...

A Nationwide Survey of Patient Centered Medical Home Demonstration Projects

Science.gov (United States)

Bitton, Asaf; Martin, Carina

2010-01-01

Background The patient centered medical home has received considerable attention as a potential way to improve primary care quality and limit cost growth. Little information exists that systematically compares PCMH pilot projects across the country. Design Cross-sectional key-informant interviews. Participants Leaders from existing PCMH demonstration projects with external payment reform. Measurements We used a semi-structured interview tool with the following domains: project history, organization and participants, practice requirements and selection process, medical home recognition, payment structure, practice transformation, and evaluation design. Results A total of 26 demonstrations in 18 states were interviewed. Current demonstrations include over 14,000 physicians caring for nearly 5 million patients. A majority of demonstrations are single payer, and most utilize a three component payment model (traditional fee for service, per person per month fixed payments, and bonus performance payments). The median incremental revenue per physician per year was $22,834 (range $720 to $91,146). Two major practice transformation models were identified—consultative and implementation of the chronic care model. A majority of demonstrations did not have well-developed evaluation plans. Conclusion Current PCMH demonstration projects with external payment reform include large numbers of patients and physicians as well as a wide spectrum of implementation models. Key questions exist around the adequacy of current payment mechanisms and evaluation plans as public and policy interest in the PCMH model grows. Electronic supplementary material The online version of this article (doi:10.1007/s11606-010-1262-8) contains supplementary material, which is available to authorized users. PMID:20467907

Social learning in nest-building birds watching live-streaming video demonstrators.

Science.gov (United States)

Guillette, Lauren M; Healy, Susan D

2018-02-13

Determining the role that social learning plays in construction behaviours, such as nest building or tool manufacture, could be improved if more experimental control could be gained over the exact public information that is provided by the demonstrator, to the observing individual. Using video playback allows the experimenter to choose what information is provided, but will only be useful in determining the role of social learning if observers attend to, and learn from, videos in a manner that is similar to live demonstration. The goal of the current experiment was to test whether live-streamed video presentations of nest building by zebra finches Taeniopygia guttata would lead observers to copy the material choice demonstrated to them. Here, males that had not previously built a nest were given an initial preference test between materials of two colours. Those observers then watched live-stream footage of a familiar demonstrator building a nest with material of the colour that the observer did not prefer. After this experience, observers were given the chance to build a nest with materials of the two colours. Although two-thirds of the observer males preferred material of the demonstrated colour after viewing the demonstrator build a nest with material of that colour more than they had previously, their preference for the demonstrated material was not as strong as that of observers that had viewed live demonstrator builders in a previous experiment. Our results suggest researchers should proceed with caution before using video demonstration in tests of social learning. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

The Work Compatibility Improvement Framework: theory and application of improvement action and intervention strategies.

Science.gov (United States)

Genaidy, Ash M; Rinder, Magda M; Sequeira, Reynold; A-Rehim, Amal D

2009-05-01

Challenges facing management of manufacturing firms can be transformed into asset gains by giving careful consideration to the worker-work environment interface. The benefits of a 'healthy' interface may lead to sizable reductions in rising health care costs and retention of highly qualified workers. This paper presents a novel approach for the 'improve' phase of the Work Compatibility Improvement Framework. The work tasks of this research consisted of: (a) fundamentals of cognitive-based improvement action and intervention; (b) design concepts and process of improvement action/intervention generation; (c) assessment model of estimated gains in company's assets; (d) application demonstration in the manufacturing sector. The process of improvement action/intervention generation is described, preceded by a description of the fundamentals of cognitive-based improvement action and intervention and system architecture. This is followed by a documentation of estimated asset gains as a result of the improvement plan. The results showed that expert workers were, on average, 78% in agreement with the algorithm-identified improvement actions. Their knowledge was used to update the recommended actions as well as to detail the multiple strategies required to address the improvement actions. As a result, an integrated improvement plan was developed resulting in estimated asset gains of $1.6 million, which was validated by the general manager. The research reported herein documented the theory and application of the 'improve' phase of the Work Compatibility Improvement Framework. The economic assessment of the suggested improvement is also reported and this has proved to be an important driver to secure the firm collaboration of manufacturing enterprise management. An integrated improvement solution plan backed by a detailed economic assessment of suggested improvements is essential to demonstrate the full potential of workplace micro- and macro-ergonomic interventions.

Central Limit Theorem: New SOCR Applet and Demonstration Activity

Science.gov (United States)

Dinov, Ivo D.; Christou, Nicolas; Sanchez, Juana

2011-01-01

Modern approaches for information technology based blended education utilize a variety of novel instructional, computational and network resources. Such attempts employ technology to deliver integrated, dynamically linked, interactive content and multifaceted learning environments, which may facilitate student comprehension and information retention. In this manuscript, we describe one such innovative effort of using technological tools for improving student motivation and learning of the theory, practice and usability of the Central Limit Theorem (CLT) in probability and statistics courses. Our approach is based on harnessing the computational libraries developed by the Statistics Online Computational Resource (SOCR) to design a new interactive Java applet and a corresponding demonstration activity that illustrate the meaning and the power of the CLT. The CLT applet and activity have clear common goals; to provide graphical representation of the CLT, to improve student intuition, and to empirically validate and establish the limits of the CLT. The SOCR CLT activity consists of four experiments that demonstrate the assumptions, meaning and implications of the CLT and ties these to specific hands-on simulations. We include a number of examples illustrating the theory and applications of the CLT. Both the SOCR CLT applet and activity are freely available online to the community to test, validate and extend (Applet: http://www.socr.ucla.edu/htmls/SOCR_Experiments.html and Activity: http://wiki.stat.ucla.edu/socr/index.php/SOCR_EduMaterials_Activities_GeneralCentralLimitTheorem). PMID:21833159

Demonstrating sustainable energy: A review-based model of sustainable energy demonstration projects

NARCIS (Netherlands)

Bossink, Bart

2017-01-01

This article develops a model of sustainable energy demonstration projects, based on a review of 229 scientific publications on demonstrations in renewable and sustainable energy. The model addresses the basic organizational characteristics (aim, cooperative form, and physical location) and learning

West Valley Demonstration Project Annual Site Environmental Report Calendar Year 2008

Energy Technology Data Exchange (ETDEWEB)

West Valley Environmental Services LLC (WVES) and URS - Washington Division

2009-09-24

Annual Site Environmental Report for the West Valley Demonstration Project (WVDP) for Calendar Year 2008. The report summarizes the calendar year (CY) 2008 environmental monitoring program data at the WVDP so as to describe the performance of the WVDP’s environmental management system (EMS), confirm compliance with standards and regulations, and highlight important programs. Monitoring and surveillance of the facilities used by the DOE are conducted to verify protection of the environment, continual improvement, prevention and/or minimization of pollution, public outreach, and stakeholder involvement. In addition to demonstrating compliance with environmental regulations and directives, evaluation of data collected in 2008 continued to indicate that WVDP activities pose no threat to public health or safety, or to the environment.

West Valley Demonstration Project Annual Site Environmental Report Calendar Year 2008

International Nuclear Information System (INIS)

2009-01-01

Annual Site Environmental Report for the West Valley Demonstration Project (WVDP) for Calendar Year 2008. The report summarizes the calendar year (CY) 2008 environmental monitoring program data at the WVDP so as to describe the performance of the WVDP's environmental management system (EMS), confirm compliance with standards and regulations, and highlight important programs. Monitoring and surveillance of the facilities used by the DOE are conducted to verify protection of the environment, continual improvement, prevention and/or minimization of pollution, public outreach, and stakeholder involvement. In addition to demonstrating compliance with environmental regulations and directives, evaluation of data collected in 2008 continued to indicate that WVDP activities pose no threat to public health or safety, or to the environment.

Photovoltaic demonstration projects

Energy Technology Data Exchange (ETDEWEB)

Gillett, W B; Hacker, R J; Kaut, W [eds.

1991-01-01

This book, the proceedings of the fourth PV-Contractors' Meeting organized by the Commission of the European Communities, Directorate-General for Energy, held at Brussels on 21 and 22 November 1989, provides an overview of the photovoltaic demonstration projects which have been supported in the framework of the Energy Demonstration Program since 1983. It includes reports by each of the contractors who submitted proposals in 1983, 1984, 1985 and 1986, describing progress with their projects. Summaries of the discussions held at the meeting, which included contractors whose projects were submitted in 1987, are also presented. The different technologies which are being demonstrated concern the modules, the cabling of the array, structure design, storage strategy and power conditioning. The various applications include desalination, communications, dairy farms, water pumping, and warning systems. Papers have been processed separately for inclusion on the data base.

Newberry EGS Demonstration: Phase 2.2 Report

Energy Technology Data Exchange (ETDEWEB)

Cladouhos, Trenton T. [AltaRock Energy, Seattle, WA (United States); Petty, Susan [AltaRock Energy, Seattle, WA (United States); Swyer, Mike W. [AltaRock Energy, Seattle, WA (United States); Nordin, Yini [AltaRock Energy, Seattle, WA (United States); Garrison, Geoff [AltaRock Energy, Seattle, WA (United States); Uddenberg, Matt [AltaRock Energy, Seattle, WA (United States); Grasso, Kyla [AltaRock Energy, Seattle, WA (United States); Stern, Paul [PLS Environmental, Boulder, CO (United States); Sonnenthal, Eric [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Foulger, Gillian [Foulger Consulting, Palo Alto, CA (United States); Julian, Bruce [Foulger Consulting, Palo Alto, CA (United States)

2015-07-03

The Newberry Volcano EGS Demonstration is a five year field project designed to demonstrate recent technological advances for engineered geothermal systems (EGS) development. Advances in reservoir stimulation, diverter, and monitoring are being tested in a hot (>300 ºC), dry well (NWG 55-29) drilled in 2008. In the fall of 2014, 9,500m3 (2.5 million gallons) of groundwater were injected at a maximum wellhead pressure of 195 bar (2850 psi) over 4 weeks of hydraulic stimulation. Injectivity changes, thermal profiles and seismicity indicate that fracture permeability in well NWG 55-29 was enhanced. The fifteen-station microseismic array (MSA) located 398 seismic events, ranging in magnitude from M 0 to M 2.26. The next step is to drill a production well into the EGS reservoir. Advanced analysis of the microseismic data including hand picking of first arrivals, moment tensors, relative relocations, and velocity model improvements have resulted new higher-quality microseismic catalogs. These catalogs have been combined by relative weighting and gridding of seismic densities, resulting in probability-based maps and cross-sections, which have been used to plan a production well trajectory. The microseismic locations and times were also used to develop a reservoir diffusivity model, which can be used to evaluate stimulation plans such as dual-well stimulation.

Maui Smart Grid Demonstration Project Managing Distribution System Resources for Improved Service Quality and Reliability, Transmission Congestion Relief, and Grid Support Functions

Energy Technology Data Exchange (ETDEWEB)

none,

2014-09-30

The Maui Smart Grid Project (MSGP) is under the leadership of the Hawaii Natural Energy Institute (HNEI) of the University of Hawaii at Manoa. The project team includes Maui Electric Company, Ltd. (MECO), Hawaiian Electric Company, Inc. (HECO), Sentech (a division of SRA International, Inc.), Silver Spring Networks (SSN), Alstom Grid, Maui Economic Development Board (MEDB), University of Hawaii-Maui College (UHMC), and the County of Maui. MSGP was supported by the U.S. Department of Energy (DOE) under Cooperative Agreement Number DE-FC26-08NT02871, with approximately 50% co-funding supplied by MECO. The project was designed to develop and demonstrate an integrated monitoring, communications, database, applications, and decision support solution that aggregates renewable energy (RE), other distributed generation (DG), energy storage, and demand response technologies in a distribution system to achieve both distribution and transmission-level benefits. The application of these new technologies and procedures will increase MECO’s visibility into system conditions, with the expected benefits of enabling more renewable energy resources to be integrated into the grid, improving service quality, increasing overall reliability of the power system, and ultimately reducing costs to both MECO and its customers.

Advanced Demonstration and Test Reactor Options Study

Energy Technology Data Exchange (ETDEWEB)

Petti, David Andrew [Idaho National Lab. (INL), Idaho Falls, ID (United States); Hill, R. [Argonne National Lab. (ANL), Argonne, IL (United States); Gehin, J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gougar, Hans David [Idaho National Lab. (INL), Idaho Falls, ID (United States); Strydom, Gerhard [Idaho National Lab. (INL), Idaho Falls, ID (United States); Heidet, F. [Argonne National Lab. (ANL), Argonne, IL (United States); Kinsey, J. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Grandy, Christopher [Argonne National Lab. (ANL), Argonne, IL (United States); Qualls, A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Brown, Nicholas [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Powers, J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hoffman, E. [Argonne National Lab. (ANL), Argonne, IL (United States); Croson, D. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2017-01-01

Global efforts to address climate change will require large-scale decarbonization of energy production in the United States and elsewhere. Nuclear power already provides 20% of electricity production in the United States (U.S.) and is increasing in countries undergoing rapid growth around the world. Because reliable, grid-stabilizing, low emission electricity generation, energy security, and energy resource diversity will be increasingly valued, nuclear power’s share of electricity production has a potential to grow. In addition, there are non electricity applications (e.g., process heat, desalination, hydrogen production) that could be better served by advanced nuclear systems. Thus, the timely development, demonstration, and commercialization of advanced nuclear reactors could diversify the nuclear technologies available and offer attractive technology options to expand the impact of nuclear energy for electricity generation and non-electricity missions. The purpose of this planning study is to provide transparent and defensible technology options for a test and/or demonstration reactor(s) to be built to support public policy, innovation and long term commercialization within the context of the Department of Energy’s (DOE’s) broader commitment to pursuing an “all of the above” clean energy strategy and associated time lines. This planning study includes identification of the key features and timing needed for advanced test or demonstration reactors to support research, development, and technology demonstration leading to the commercialization of power plants built upon these advanced reactor platforms. This planning study is consistent with the Congressional language contained within the fiscal year 2015 appropriation that directed the DOE to conduct a planning study to evaluate “advanced reactor technology options, capabilities, and requirements within the context of national needs and public policy to support innovation in nuclear energy�

Advanced Demonstration and Test Reactor Options Study

International Nuclear Information System (INIS)

Petti, David Andrew; Hill, R.; Gehin, J.; Gougar, Hans David; Strydom, Gerhard; Heidet, F.; Kinsey, J.; Grandy, Christopher; Qualls, A.; Brown, Nicholas; Powers, J.; Hoffman, E.; Croson, D.

2017-01-01

Global efforts to address climate change will require large-scale decarbonization of energy production in the United States and elsewhere. Nuclear power already provides 20% of electricity production in the United States (U.S.) and is increasing in countries undergoing rapid growth around the world. Because reliable, grid-stabilizing, low emission electricity generation, energy security, and energy resource diversity will be increasingly valued, nuclear power's share of electricity production has a potential to grow. In addition, there are non electricity applications (e.g., process heat, desalination, hydrogen production) that could be better served by advanced nuclear systems. Thus, the timely development, demonstration, and commercialization of advanced nuclear reactors could diversify the nuclear technologies available and offer attractive technology options to expand the impact of nuclear energy for electricity generation and non-electricity missions. The purpose of this planning study is to provide transparent and defensible technology options for a test and/or demonstration reactor(s) to be built to support public policy, innovation and long term commercialization within the context of the Department of Energy's (DOE's) broader commitment to pursuing an 'all of the above' clean energy strategy and associated time lines. This planning study includes identification of the key features and timing needed for advanced test or demonstration reactors to support research, development, and technology demonstration leading to the commercialization of power plants built upon these advanced reactor platforms. This planning study is consistent with the Congressional language contained within the fiscal year 2015 appropriation that directed the DOE to conduct a planning study to evaluate 'advanced reactor technology options, capabilities, and requirements within the context of national needs and public policy to support innovation in nuclear energy'. Advanced reactors are

The Evritania (Greece) demonstration plant of biomass pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Zabaniotou, A.A.; Karabela, A.J. [Aristotle University of Thessaloniki (Greece). Dept. of Chemical Engineering and Chemical Process Engineering Research Institute

1999-06-01

This paper is focused on describing the Evritania demonstration plant for pyrolysis of forestry biomass. This plant was constructed in the village of Voulpi, district of Evritania, in central Greece, in 1995, with a threefold purpose; development of know-how, forest fire prevention and rural development. The products are charcoal and bio-oil. The plant capacity is 1200-1450 kg/h of wet biomass and the pyrolysis temperature is approx. 400 deg C. The raw material used is Arbutus unedo, which is an evergreen broad-leaf tree which covers the area. Other agricultural waste could also be used, such as olive pits and cuttings, almond shells and cotton kernels. The paper includes the conceptual process flow sheet, the changes and improvements made during the trial phase, data from the start-up phase, and product characteristics. Comparison of the process with the Alten process is presented. Additionally, comparisons are made of product characteristics with those from other pyrolysis processes. In general, the results obtained are encouraging even though several improvements of the pilot plant are required. (author)

Full parabolic trough qualification from prototype to demonstration loop

Science.gov (United States)

Janotte, Nicole; Lüpfert, Eckhard; Pottler, Klaus; Schmitz, Mark

2017-06-01

On the example of the HelioTrough® collector development the full accompanying and supporting qualification program for large-scale parabolic trough collectors for solar thermal power plants is described from prototype to demonstration loop scale. In the evaluation process the actual state and the optimization potential are assessed. This includes the optical and geometrical performance determined by concentrator shape, deformation, assembly quality and local intercept factor values. Furthermore, its mechanical performance in terms of tracking accuracy and torsional stiffness and its thermal system performance on the basis of the overall thermal output and heat loss are evaluated. Demonstration loop tests deliver results of collector modules statistical slope deviation of 1.9 to 2.6 mrad, intercept factor above 98%, peak optical performance of 81.6% and heat loss coefficients from field tests. The benefit of such a closely monitored development lies in prompt feedback on strengths, weaknesses and potential improvements on the new product at any development stage from first module tests until demonstration loop evaluation. The product developer takes advantage of the achieved technical maturity, already before the implementation in a commercial power plant. The well-understood performance characteristics allow the reduction of safety margins making the new HelioTrough collector competitive from the start.

VANTAGE 5 PWR fuel assembly demonstration program at Virgil C. Summer nuclear station

International Nuclear Information System (INIS)

Warner, D.C.; Orr, W.L.

1985-01-01

VANTAGE 5 is an improved PWR fuel product designed and manufactured by Westinghouse Electric Corporation. The VANTAGE 5 fuel design features integral fuel burnable absorbers, intermediate flow mixer grids, axial blankets, high burnup capability, and a reconstitutable top nozzle. A demonstration program for this fuel design commenced in late 1984 in cycle 2 of the Virgil C. Summer Nuclear Station. Objectives for VANTAGE 5 fuel are reduced fuel cycle costs, better core operating margins, and increased design and operating flexibility. Inspections of the VANTAGE 5 demonstration assemblies are planned at each refueling outage

Astronomy LITE Demonstrations

Science.gov (United States)

Brecher, Kenneth

2006-12-01

Project LITE (Light Inquiry Through Experiments) is a materials, software, and curriculum development project. It focuses on light, optics, color and visual perception. According to two recent surveys of college astronomy faculty members, these are among the topics most often included in the large introductory astronomy courses. The project has aimed largely at the design and implementation of hands-on experiences for students. However, it has also included the development of lecture demonstrations that employ novel light sources and materials. In this presentation, we will show some of our new lecture demonstrations concerning geometrical and physical optics, fluorescence, phosphorescence and polarization. We have developed over 200 Flash and Java applets that can be used either by teachers in lecture settings or by students at home. They are all posted on the web at http://lite.bu.edu. For either purpose they can be downloaded directly to the user's computer or run off line. In lecture demonstrations, some of these applets can be used to control the light emitted by video projectors to produce physical effects in materials (e.g. fluorescence). Other applets can be used, for example, to demonstrate that the human percept of color does not have a simple relationship with the physical frequency of the stimulating source of light. Project LITE is supported by Grant #DUE-0125992 from the NSF Division of Undergraduate Education.

Buried Waste Integrated Demonstration

International Nuclear Information System (INIS)

1994-03-01

The Buried Waste Integrated Demonstration (BWID) supports the applied research, development, demonstration, and evaluation of a suite of advanced technologies that offer promising solutions to the problems associated with the remediation of buried waste. BWID addresses the difficult remediation problems associated with DOE complex-wide buried waste, particularly transuranic (TRU) contaminated buried waste. BWID has implemented a systems approach to the development and demonstration of technologies that will characterize, retrieve, treat, and dispose of DOE buried wastes. This approach encompasses the entire remediation process from characterization to post-monitoring. The development and demonstration of the technology is predicated on how a technology fits into the total remediation process. To address all of these technological issues, BWID has enlisted scientific expertise of individuals and groups from within the DOE Complex, as well as experts from universities and private industry. The BWID mission is to support development and demonstration of a suite of technologies that, when integrated with commercially-available technologies, forms a comprehensive, remediation system for the effective and efficient remediation of buried waste throughout the DOE Complex. BWID will evaluate and validate demonstrated technologies and transfer this information and equipment to private industry to support the Office of Environmental Restoration (ER), Office of Waste Management (WM), and Office of Facility Transition (FT) remediation planning and implementation activities

Demonstrating Empathy for Foreign-Born Employees through Openness and Acceptance: A Quasi-Experimental Field Study.

Science.gov (United States)

Stull, James B.

1986-01-01

Reports on a study measuring foreign-born employees' perceptions of supervisors' acceptance of and openness to "open" messages from the employee. Suggests ways to improve supervisory demonstrations of empathy. (MS)

Improving quantitative gas chromatography-electron ionization mass spectrometry results using a modified ion source: demonstration for a pharmaceutical application.

Science.gov (United States)

D'Autry, Ward; Wolfs, Kris; Hoogmartens, Jos; Adams, Erwin; Van Schepdael, Ann

2011-07-01

Gas chromatography-mass spectrometry is a well established analytical technique. However, mass spectrometers with electron ionization sources may suffer from signal drifts, hereby negatively influencing quantitative performance. To demonstrate this phenomenon for a real application, a static headspace-gas chromatography method in combination with electron ionization-quadrupole mass spectrometry was optimized for the determination of residual dichloromethane in coronary stent coatings. Validating the method, the quantitative performance of an original stainless steel ion source was compared to that of a modified ion source. Ion source modification included the application of a gold coating on the repeller and exit plate. Several validation aspects such as limit of detection, limit of quantification, linearity and precision were evaluated using both ion sources. It was found that, as expected, the stainless steel ion source suffered from signal drift. As a consequence, non-linearity and high RSD values for repeated analyses were obtained. An additional experiment was performed to check whether an internal standard compound would lead to better results. It was found that the signal drift patterns of the analyte and internal standard were different, consequently leading to high RSD values for the response factor. With the modified ion source however, a more stable signal was observed resulting in acceptable linearity and precision. Moreover, it was also found that sensitivity improved compared to the stainless steel ion source. Finally, the optimized method with the modified ion source was applied to determine residual dichloromethane in the coating of coronary stents. The solvent was detected but found to be below the limit of quantification. Copyright © 2011 Elsevier B.V. All rights reserved.

Interpretation of gamma-scanning data from the ORR demonstration elements

International Nuclear Information System (INIS)

Bretscher, M.M.; Snelgrove, J.L.; Hobbs, R.W.

1989-01-01

The HEU and LEU fuel elements used in the ORR whole-core demonstration were gamma-scanned to determine the axial distribution of the 140 La and 137 Cs activities. Analysis of this data is now complete. From the 140 La activity distributions cycle-averaged powers were determined while the 137 Cs data provided a measure of the final 235 U burnup in the fuel elements. A method for calculating correction factors for activity gradients transverse to the fuel element axis is presented and is applied to the first mixed core used in the demonstration during the gradual transition to an all LEU core. Results based on the gamma-scanning of the LEU fuel followers are also presented. Improved burnup calculations against which the experimental results are to be compared are now in progress. 7 refs., 21 figs., 3 tabs

Biodiesel Mass Transit Demonstration

Science.gov (United States)

2010-04-01

The Biodiesel Mass Transit Demonstration report is intended for mass transit decision makers and fleet managers considering biodiesel use. This is the final report for the demonstration project implemented by the National Biodiesel Board under a gran...

Continual improvement plan

Science.gov (United States)

1994-01-01

NASA's approach to continual improvement (CI) is a systems-oriented, agency-wide approach that builds on the past accomplishments of NASA Headquarters and its field installations and helps achieve NASA's vision, mission, and values. The NASA of the future will fully use the principles of continual improvement in every aspect of its operations. This NASA CI plan defines a systematic approach and a model for continual improvement throughout NASA, stressing systems integration and optimization. It demonstrates NASA's constancy of purpose for improvement - a consistent vision of NASA as a worldwide leader in top-quality science, technology, and management practices. The CI plan provides the rationale, structures, methods, and steps, and it defines NASA's short term (1-year) objectives for improvement. The CI plan presents the deployment strategies necessary for cascading the goals and objectives throughout the agency. It also provides guidance on implementing continual improvement with participation from top leadership and all levels of employees.

Polarized Light Corridor Demonstrations.

Science.gov (United States)

Davies, G. R.

1990-01-01

Eleven demonstrations of light polarization are presented. Each includes a brief description of the apparatus and the effect demonstrated. Illustrated are strain patterns, reflection, scattering, the Faraday Effect, interference, double refraction, the polarizing microscope, and optical activity. (CW)

Comparing Demonstratives in Kwa

African Journals Online (AJOL)

This paper is a comparative study of demonstrative forms in three K wa languages, ... relative distance from the deictic centre, such as English this and that, here and there. ... Mostly, the referents of demonstratives are 'activated' or at least.

Genetic improvement of tropical acacias: achievements and ...

African Journals Online (AJOL)

The potential for genetic improvement in form traits and wood properties has also been demonstrated. Genetic improvement objectives must now give heavy weighting to improving disease resistance and tolerance. Ganoderma root rot and Ceratocystis stem wilt have destroyed large areas of acacia plantations in Indonesia ...

Tested Demonstrations.

Science.gov (United States)

Gilbert, George L., Ed.

1987-01-01

Describes two demonstrations to illustrate characteristics of substances. Outlines a method to detect the changes in pH levels during the electrolysis of water. Uses water pistols, one filled with methane gas and the other filled with water, to illustrate the differences in these two substances. (TW)

Integrating empowerment evaluation and quality improvement to achieve healthcare improvement outcomes.

Science.gov (United States)

Wandersman, Abraham; Alia, Kassandra Ann; Cook, Brittany; Ramaswamy, Rohit

2015-10-01

While the body of evidence-based healthcare interventions grows, the ability of health systems to deliver these interventions effectively and efficiently lags behind. Quality improvement approaches, such as the model for improvement, have demonstrated some success in healthcare but their impact has been lessened by implementation challenges. To help address these challenges, we describe the empowerment evaluation approach that has been developed by programme evaluators and a method for its application (Getting To Outcomes (GTO)). We then describe how GTO can be used to implement healthcare interventions. An illustrative healthcare quality improvement example that compares the model for improvement and the GTO method for reducing hospital admissions through improved diabetes care is described. We conclude with suggestions for integrating GTO and the model for improvement. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Solar cells. Proposal for a national strategy for research, development and demonstration; Solceller. Oplaeg til en national strategi for forskning, udvikling og demonstration

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

The Danish Energy Authority, Elkraft System and Eltra have initiated collaboration on the development of national R and D strategies for a number of energy technologies including solar cells. The aim is to ensure a coordinated national effort as regards research, development and demonstration within societal and energy political frames, and, furthermore, to ensure coordination with similar international initiatives, especially within the European Union. The overall aim is for the Danish solar cell strategy to contribute to support Danish national energy policy and to ensure and improve Danish competence, which can manifest itself internationally. The efforts within solar cell technology must aim at increasing solar cell systems' efficiency and service life, and furthermore, aim at reducing production costs. Hereby the efforts can contribute to an improvement of solar cell systems' competitive power in relation to other power production technologies with a view to make installation of solar cell systems attractive, both in Denmark and internationally. (BA)

Business process modeling for the Virginia Department of Transportation : a demonstration with the integrated six-year improvement program and the statewide transportation improvement program : executive summary.

Science.gov (United States)

2005-01-01

This effort demonstrates business process modeling to describe the integration of particular planning and programming activities of a state highway agency. The motivations to document planning and programming activities are that: (i) resources for co...

Demonstrating and implementing innovative technologies: Case studies from the USDOE Office of Technology Development

International Nuclear Information System (INIS)

Brouns, T.M.; Koegler, K.J.; Mamiya, L.S.

1995-02-01

This paper describes elements of success for demonstration, evaluation, and transfer for deployment of innovative technologies for environmental restoration. They have been compiled from lessons learned through the US Department of Energy (DOE) Office of Technology Development's Volatile Organic Compounds in Arid Soil Integrated Demonstration (VOC-Arid ID). The success of the VOC-Arid ID program was determined by the rapid development demonstration, and transfer for deployment of technologies to operational sites that improve on safety, cost, and/or schedule of performance over baseline technologies. The VOC-Arid ID successfully fielded more than 25 innovative technology field demonstrations; several of the technologies demonstrated have been successfully transferred for deployment Field demonstration is a critical element in the successful transfer of innovative technologies into environmental restoration operations. The measures of success for technology demonstrations include conducting the demonstration in a safe and controlled environment and generating the appropriate information by which to evaluate the technology. However, field demonstrations alone do not guarantee successful transfer for deployment There are many key elements throughout the development and demonstration process that have a significant impact on the success of a technology. This paper presents key elements for a successful technology demonstration and transfer for deployment identified through the experiences of the VOC-Arid ID. Also, several case studies are provided as examples

Cooled Ceramic Matrix Composite Propulsion Structures Demonstrated

Science.gov (United States)

Jaskowiak, Martha H.; Dickens, Kevin W.

2005-01-01

NASA's Next Generation Launch Technology (NGLT) Program has successfully demonstrated cooled ceramic matrix composite (CMC) technology in a scramjet engine test. This demonstration represented the world s largest cooled nonmetallic matrix composite panel fabricated for a scramjet engine and the first cooled nonmetallic composite to be tested in a scramjet facility. Lightweight, high-temperature, actively cooled structures have been identified as a key technology for enabling reliable and low-cost space access. Tradeoff studies have shown this to be the case for a variety of launch platforms, including rockets and hypersonic cruise vehicles. Actively cooled carbon and CMC structures may meet high-performance goals at significantly lower weight, while improving safety by operating with a higher margin between the design temperature and material upper-use temperature. Studies have shown that using actively cooled CMCs can reduce the weight of the cooled flow-path component from 4.5 to 1.6 lb/sq ft and the weight of the propulsion system s cooled surface area by more than 50 percent. This weight savings enables advanced concepts, increased payload, and increased range. The ability of the cooled CMC flow-path components to operate over 1000 F hotter than the state-of-the-art metallic concept adds system design flexibility to space-access vehicle concepts. Other potential system-level benefits include smaller fuel pumps, lower part count, lower cost, and increased operating margin.

Development, testing, and demonstration of an optimal fine coal cleaning circuit

International Nuclear Information System (INIS)

Mishra, M.; Placha, M.; Bethell, P.

1995-01-01

The overall objective of this project is to improve the efficiency of fine coal cleaning. The project will be completed in two phases: bench-scale testing and demonstration of four advanced flotation cells and; in-plant proof-of-concept (POC) pilot plant testing of two flotation cells individually and in two-stage combinations. The goal is to ascertain if a two-stage circuit can result in reduced capital and operating costs while achieving improved separation efficiency. The plant selected for this project, Cyprus Emerald Coal Preparation plant, cleans 1200 tph of raw coal. The plant produces approximately 4 million tonnes of clean coal per year at an average as received energy content of 30.2 MJ/Kg (13,000 Btu/lb)

Development, testing, and demonstration of an optimal fine coal cleaning circuit

Energy Technology Data Exchange (ETDEWEB)

Mishra, M.; Placha, M.; Bethell, P. [and others

1995-11-01

The overall objective of this project is to improve the efficiency of fine coal cleaning. The project will be completed in two phases: bench-scale testing and demonstration of four advanced flotation cells and; in-plant proof-of-concept (POC) pilot plant testing of two flotation cells individually and in two-stage combinations. The goal is to ascertain if a two-stage circuit can result in reduced capital and operating costs while achieving improved separation efficiency. The plant selected for this project, Cyprus Emerald Coal Preparation plant, cleans 1200 tph of raw coal. The plant produces approximately 4 million tonnes of clean coal per year at an average as received energy content of 30.2 MJ/Kg (13,000 Btu/lb).

Notional Airspace Operations Demonstration Plan

Science.gov (United States)

Trongale, Nicholas A.

2006-01-01

The airspace operations demonstration (AOD) is intended to show that the Access 5 Step 1 functional requirements can be met. The demonstration will occur in two phases. The initial on-range phase will be carried out in restricted airspace to demonstrate the cooperative collision avoidance (CCA) functional requirements and to provide risk-reduction for the AOD by allowing the test team to rehearse some elements of the demonstration mission. The CCA system to be used in these flights is based on Automatic Dependent Surveillance-Broadcast (ADS-B) which is a commercially-available system by which airplanes constantly broadcast their current position and altitude to other aircraft and ground resources over a dedicated radio datalink. The final phase will occur in the national airspace (NAS) and will be the formal demonstration of the remainder of the proposed functional requirements. The general objectives of the AOD are as follows: (1) Demonstrate that the UAS can aviate in the NAS (2) Demonstrate that the UAS can navigate in the NAS (3) Demonstrate that the UAS can communicate with the NAS (4) Demonstrate that the UAS can perform selected collision avoidance functions in the NAS (5) Demonstrate that the UAS can evaluate and avoid weather conflicts in the NAS (6) Demonstrate that the UAS can provide adequate command and control in the NAS In addition to the stated objectives, there are a number of goals for the flight demonstration. The demo can be accomplished successfully without achieving these goals, but these goals are to be used as a guideline for preparing for the mission. The goals are: (1) Mission duration of at least 24 hours (2) Loiter over heavy traffic to evaluate the data block issue identified during the Access 5 Airspace Operations Simulations (3) Document the contingency management process and lessons learned (4) Document the coordination process for Ground Control Stations (GCS) handoff (5) Document lessons learned regarding the process of flying in

E/Z MAS demonstration

International Nuclear Information System (INIS)

Boor, M.G.; Hurford, J.M.; Landry, R.P.; Martinez, B.J.; Solem, A.M.; Whiteson, R.; Zardecki, A.

1998-01-01

Los Alamos National Laboratory has developed E/Z MAS, a new generation nuclear material accountability application based on the latest technology and designed for facilities required to track nuclear materials with a simple-to-use interface. E/Z MAS is based on years of experience spent developing nuclear material accounting systems. E/Z MAS uses a modern relational database with a web server and enables users on a classified local area network to interact with the database with web browsers. The E/Z MAS Demonstration poster session demonstrates the E/Z MAS functions required by an operational nuclear facility to track material as it enters and leaves a facility and to account for the material as it moves through a process. The generation of internal facility reports and external reports for the Russian Federal system will be demonstrated. Bar-code readers will be used to demonstrate the ability of EZ MAS to automate certain functions, such as physical inventories at facilities

Numerical simulations in support of the in situ bioremediation demonstration at Savannah River

International Nuclear Information System (INIS)

Travis, B.J.; Rosenberg, N.D.

1994-06-01

This report assesses the performance of the in situ bioremediation technology demonstrated at the Savannah River Integrated Demonstration (SRID) site in 1992--1993. The goal of the technology demonstration was to stimulate naturally occurring methanotrophic bacteria at the SRID site with injection of methane, air and air-phase nutrients (nitrogen and phosphate) such that significant amounts of the chlorinated solvent present in the subsurface would be degraded. Our approach is based on site-specific numerical simulations using the TRAMP computer code. In this report, we discuss the interactions among the physical and biochemical processes involved in in situ bioremediation. We also investigate improvements to technology performance, make predictions regarding the performance of this technology over long periods of time and at different sites, and compare in situ bioremediation with other remediation technologies

Staunton 1 Reclamation Demonstration Project. Progress report II

Energy Technology Data Exchange (ETDEWEB)

None

1979-07-01

The Staunton 1 Reclamation Demonstration Project involves an evaluation of the reclamation process on a 13.8-ha abandoned deep coal mine refuse site in southwestern Illinois. The procedure included collection of preconstruction environmental data, determination of the site's final land use, and development and implementation of a detailed site development plan. Approximately 9.3 ha of refuse material was recontoured, covered with a minimum of 30 cm of soil obtained on site, and seeded with a mixture of grasses and legumes. Hydrologic investigation indicates some improvement in groundwater quality. Surface water quality also has shown improvement, but development of the aquatic ecosystem in the newly-constructed pond is slow. Revegetation has been successful, and a protective plant cover has been established on most areas of the site. Soil tests indicate that acceptable plant growth media have been constructed; however, continued application of fertilizer and limestone will probably be necessary to maintain the vegetation. The soil microbial community has achieved total numbers equal to those of old fields, but species' diversity is low. Small mammals, birds, reptiles, and amphibians have invaded and are utilizing the site. The economic value of the site and adjacent property has increased substantially, and the area's aesthetic value has been enhanced significantly. The two-year period of intensive monitoring and evaluation has been utilized to develop recommendations for improving the designs of future reclamation efforts.

Demonstration of Femtosecond-Phase Stabilization in 2 km Optical Fiber

International Nuclear Information System (INIS)

Staples, J.W.; Wilcox, R.; Byrd, J.M.

2007-01-01

Long-term phase drifts of less than a femtosecond per hour have been demonstrated in a 2 km length of single-mode optical fiber, stabilized interferometrically at 1530 nm. Recent improvements include a wide-band phase detector that reduces the possibility of fringe jumping due to fast external perturbations of the fiber and locking of the master CW laser wavelength to an atomic absorption line. Mode-locked lasers may be synchronized using two wavelengths of the comb, multiplexed over one fiber, each wavelength individually interferometrically stabilized

Helicopter detection and classification demonstrator

NARCIS (Netherlands)

Koersel, A.C. van

2000-01-01

A technology demonstrator that detects and classifies different helicopter types automatically, was developed at TNO-FEL. The demonstrator is based on a PC, which receives its acoustic input from an all-weather microphone. The demonstrator uses commercial off-the-shelf hardware to digitize the

Design, construction, and operations experience with the SWSA 6 [Solid Waste Storage Area] Tumulus Disposal Demonstration

International Nuclear Information System (INIS)

Van Hoesen, S.D.; Van Cleve, J.E.; Wylie, A.N.; Williams, L.C.; Bolinsky, J.

1988-01-01

Efforts are underway at the Department of Energy facilities in Oak Ridge to improve the performance of radioactive waste disposal facilities. An engineered disposal concept demonstration involving placement of concrete encased waste on a monitored concrete pad with an earthen cover is being conducted. The design, construction, and operations experience with this project, the SWSA 6 Tumulus Disposal Demonstration, is described. 1 fig., 1 tab

Tested Demonstrations.

Science.gov (United States)

Gilbert, George L.

1983-01-01

An apparatus is described in which effects of pressure, volume, and temperature changes on a gas can be observed simultaneously. Includes use of the apparatus in demonstrating Boyle's, Gay-Lussac's, and Charles' Laws, attractive forces, Dalton's Law of Partial pressures, and in illustrating measurable vapor pressures of liquids and some solids.…

Teleoperation for learning by demonstration

DEFF Research Database (Denmark)

Kukliński, Kamil; Fischer, Kerstin; Marhenke, Ilka

2014-01-01

Learning by demonstration is a useful technique to augment a robot's behavioral inventory, and teleoperation allows lay users to demonstrate novel behaviors intuitively to the robot. In this paper, we compare two modes of teleoperation of an industrial robot, the demonstration by means of a data...... glove and by means of a control object (peg). Experiments with 16 lay users, performing assembly task on the Cranfield benchmark objects, show that the control peg leads to more success, more efficient demonstration and fewer errors....

An A BWR demonstration simulator for training and developing technical staff

International Nuclear Information System (INIS)

Powers, J.; Yonezawa, H.; Aoyagi, Y.; Kataoka, K.

2015-09-01

The US-Advanced Boiling Water Reactor (A BWR), certified by the US NRC, is a third generation, evolutionary boiling water reactor design which is the reference for the South Texas Project Units 3 and 4 (STP3-4) Combined License Application (Cola). Nuclear Innovation North America (Nina) is the License Applicant for this new build project, and Toshiba is the selected primary technology contractor. Toshiba has developed a Demonstration Simulator of the A BWR control room that provides a realistic experience for training and education on BWR principles and operations fundamentals. The Demonstration Simulator is located in the Toshiba America Nuclear Energy (Tane) office in Charlotte, North Carolina and is composed of standard office computer equipment set up in a specific arrangement that is representative of the layout of an A BWR control room. The Demonstration Simulator is not intended for licensed operator training, but can provide a framework for encouraging entry level technically oriented nuclear workers to enter the operations field; strengthening the linkage between university energy field curricula and real-life application of theory; and, improving understanding of integrated plant operations for developing station technical staff. This paper describes the A BWR Demonstration Simulator and its applications for training and educating future nuclear workers. (Author)

An A BWR demonstration simulator for training and developing technical staff

Energy Technology Data Exchange (ETDEWEB)

Powers, J. [Toshiba America Nuclear Energy, Charlotte, North Carolina (United States); Yonezawa, H.; Aoyagi, Y.; Kataoka, K., E-mail: jim.powers@toshiba.com [Toshiba Corporation, Kawasaki, Kanagawa (Japan)

2015-09-15

The US-Advanced Boiling Water Reactor (A BWR), certified by the US NRC, is a third generation, evolutionary boiling water reactor design which is the reference for the South Texas Project Units 3 and 4 (STP3-4) Combined License Application (Cola). Nuclear Innovation North America (Nina) is the License Applicant for this new build project, and Toshiba is the selected primary technology contractor. Toshiba has developed a Demonstration Simulator of the A BWR control room that provides a realistic experience for training and education on BWR principles and operations fundamentals. The Demonstration Simulator is located in the Toshiba America Nuclear Energy (Tane) office in Charlotte, North Carolina and is composed of standard office computer equipment set up in a specific arrangement that is representative of the layout of an A BWR control room. The Demonstration Simulator is not intended for licensed operator training, but can provide a framework for encouraging entry level technically oriented nuclear workers to enter the operations field; strengthening the linkage between university energy field curricula and real-life application of theory; and, improving understanding of integrated plant operations for developing station technical staff. This paper describes the A BWR Demonstration Simulator and its applications for training and educating future nuclear workers. (Author)

Demonstration Project 111, ITS/CVO Technology Truck, Final Project Report

Energy Technology Data Exchange (ETDEWEB)

Gambrell, KP

2002-01-11

In 1995, the planning and building processes began to design and develop a mobile demonstration unit that could travel across the nation and be used as an effective outreach tool. In 1997, the unit was completed; and from June 1997 until December 2000, the Federal Highway Administration (FHWA)/Federal Motor Carrier Safety Administration (FMCSA) mobilized the Technology Truck, also known as Demonstration Project No. 111, ''Advanced Motor Carrier Operations and Safety Technologies.'' The project featured the latest available state-of-the-practice intelligent transportation systems (ITS) technologies designed to improve both the efficiency and safety of commercial vehicle operations (CVO). The Technology Truck was designed to inform and educate the motor carrier community and other stakeholders regarding ITS technologies, thus gaining support and buy-in for participation in the ITS program. The primary objective of the project was to demonstrate new and emerging ITS/CVO technologies and programs, showing their impact on motor carrier safety and productivity. In order to meet the objectives of the Technology Truck project, the FHWA/FMCSA formed public/private partnerships with industry and with Oak Ridge National Laboratory to demonstrate and display available ITS/CVO technologies in a cooperative effort. The mobile demonstration unit was showcased at national and regional conferences, symposiums, universities, truck shows and other venues, in an effort to reach as many potential users and decision makers as possible. By the end of the touring phase, the ITS/CVO Technology Truck had been demonstrated in 38 states, 4 Canadian provinces, 88 cities, and 114 events; been toured by 18,099 people; and traveled 115,233 miles. The market penetration for the Technology Truck exceeded 4,000,000, and the website received more than 25,000 hits. In addition to the Truck's visits, the portable ITS/CVO kiosk was demonstrated at 31 events in 23 cites in 15

On-Detector Electronics for the ATLAS TileCal Demonstrator

CERN Document Server

Muschter, Steffen Lothar; The ATLAS collaboration; Anderson, Kelby; Bohm, Christian; Drake, Gary; Oreglia, Mark; Paramonov, Alexander; Tang, Fukun

2014-01-01

In the major upgrade of the LHC and its detectors around year 2023 the beam energy and luminosity will increase significantly. For TileCal, the hadron calorimeter in ATLAS, most of the on-detector and off-detector electronics will be replaced. A new design has been proposed with some alternative solutions for some of the parts. To gain experience with this design, a demonstrator project is on-going aiming at inserting a prototype module in ATLAS this summer or in the next possible shut-down. A caveat is that it must be able to operate seamlessly with the present system. This together with test beam studies will help to finalize the design. The on-detector part of the demonstrator electronics contains five parts: new front-end boards, digitizer boards with a link daughter board, a programmable high voltage power supply and a redundant low voltage power supply. Apart from improved performance reliability is a main concern. This will be achieved by increased modularity so that the consequences of a complete fail...

On-Detector Electronics for the ATLAS TileCal Demonstrator

CERN Document Server

Muschter, Steffen Lothar; The ATLAS collaboration; Akerstedt, Henrik; Anderson, Kelby; Bohm, Christian; Drake, Gary; Oreglia, Mark; Paramonov, Alexander; Tang, Fukun

2016-01-01

In the major upgrade of the LHC and its detectors around year 2023 the beam energy and luminosity will increase significantly. For TileCal, the hadron calorimeter in ATLAS, most of the on-detector and off-detector electronics will be replaced. A new design has been proposed with some alternative solutions for some of the parts. To gain experience with this design, a demonstrator project is on-going aiming at inserting a prototype module in ATLAS this summer or in the next possible shut-down. A caveat is that it must be able to operate seamlessly with the present system. This together with test beam studies will help to finalize the design. The on-detector part of the demonstrator electronics contains five parts: new front-end boards, digitizer boards with a link daughter board, a programmable high voltage power supply and a redundant low voltage power supply. Apart from improved performance reliability is a main concern. This will be achieved by increased modularity so that the consequences of a complete fail...

DEMONSTRATION OF A FULL-SCALE RETROFIT OF THE ADVANCED HYBRID PARTICULATE COLLECTOR TECHNOLOGY

Energy Technology Data Exchange (ETDEWEB)

Tom Hrdlicka; William Swanson

2005-12-01

The Advanced Hybrid Particulate Collector (AHPC), developed in cooperation between W.L. Gore & Associates and the Energy & Environmental Research Center (EERC), is an innovative approach to removing particulates from power plant flue gas. The AHPC combines the elements of a traditional baghouse and electrostatic precipitator (ESP) into one device to achieve increased particulate collection efficiency. As part of the Power Plant Improvement Initiative (PPII), this project was demonstrated under joint sponsorship from the U.S. Department of Energy and Otter Tail Power Company. The EERC is the patent holder for the technology, and W.L. Gore & Associates was the exclusive licensee for this project. The project objective was to demonstrate the improved particulate collection efficiency obtained by a full-scale retrofit of the AHPC to an existing electrostatic precipitator. The full-scale retrofit was installed on an electric power plant burning Powder River Basin (PRB) coal, Otter Tail Power Company's Big Stone Plant, in Big Stone City, South Dakota. The $13.4 million project was installed in October 2002. Project related testing concluded in December 2005. The following Final Technical Report has been prepared for the project entitled ''Demonstration of a Full-Scale Retrofit of the Advanced Hybrid Particulate Collector Technology'' as described in DOE Award No. DE-FC26-02NT41420. The report presents the operation and performance results of the system.

Demonstration of inherent safety features of HTGRs using the HTTR

International Nuclear Information System (INIS)

Tachibana, Yukio; Nakagawa, Shigeaki; Nakazawa, Toshio; Iyoku, Tatsuo

2004-01-01

Safety demonstration tests using the High Temperature Engineering Test Reactor (HTTR) are conducted for the purpose of demonstrating inherent safety features of High Temperature Gas-cooled Reactors (HTGRs) quantitatively as well as providing the core and plant transient data for validation of HTGR analysis codes for safety evaluation. The safety demonstration test are divided to the first phase and second phase tests. In the first phase tests, simulation tests of anticipated operational occurrences and anticipated transients without scram (ATWS) are conducted. The second phase tests will simulate accidents such as a depressurization accident (loss of coolant accident). The first phase test simulating reactivity insertion events and coolant flow reduction events stared in FY 2002. Post-test analyses have been conducted to reproduced the test results by using the core and plant dynamics analysis code, ACCORD and Monte Carlo code, MVP. The analysis results agreed fairly well with the test results of a control rod withdrawal test simulating reactivity insertion, and gas circulators trip test simulating coolant flow reduction, at power levels of 50% and 30% of the rated power, respectively. It is shown that improvement of the ACCORD code by taking into consideration vertical and horizontal temperature distribution gives better analysis results in the control rod withdrawal test. The fist phase safety demonstration tests will continue until FY 2005, and the second phase tests are planned to be started in FY 2006. (author)

Effect of different single-session educational modalities on improving medical students' ability to demonstrate proper pressurized metered dose inhaler technique.

Science.gov (United States)

Dominelli, Giulio S; Dominelli, Paolo B; Rathgeber, Steven L; Webster, Sheila B

2012-05-01

Pressurized metered dose inhalers (pMDIs) remain important therapeutic options for obstructive lung diseases. The ability to instruct and evaluate inhaler technique is a crucial skill that all medical professionals should possess; unfortunately, many professionals lack proficiency with pMDIs. We aimed to determine if brief education interventions of differing modalities can positively affect medical students' skills over the long term. The baseline ability of medical students and first year residents to use pMDIs was scored via a 10-point scoring system. Students were randomized to receive no education, one-on-one instruction, or video instruction. Students were then retested immediately after the education and at the 3-month mark for retention of acquired skills. Video, one-on-one and the placebo groups modalities statistically improved the average medical student's score in the immediate retesting (7.5 and 7.4 vs. 4.7, p grades at the immediate recall significantly improved for both modalities. During retention testing, only video education had a statistically significant improvement in pass rate over the control group, as defined by an average score of 7 or better (8 vs. 1, p improve medical students' ability to use pMDIs in short-term testing. However, only video education retained significant improvement compared with control after 3 months. This suggests that compared with traditional one-on-one teaching, video education is an effective means of teaching medical students how to improve their pMDI technique.

Improving Student Behavior.

Science.gov (United States)

Green, Pamela; Gilbert, Janice T.

This report describes a program for improving the behavior of seventh and eighth grade students with learning disabilities in a self-contained classroom setting. Analysis of probable causes revealed that students demonstrated a lack of problem-solving skills, showed a low frustration tolerance, and exhibited poor self-concepts. Two major…

RIVERTON DOME GAS EXPLORATION AND STIMULATION TECHNOLOGY DEMONSTRATION, WIND RIVER BASIN, WYOMING

International Nuclear Information System (INIS)

Dr. Ronald C. Surdam

1999-01-01

This project will provide a full demonstration of an entirely new package of exploration technologies that will result in the discovery and development of significant new gas reserves now trapped in unconventional low-permeability reservoirs. This demonstration includes the field application of these technologies, prospect definition and well siting, and a test of this new strategy through wildcat drilling. In addition this project includes a demonstration of a new stimulation technology that will improve completion success in these unconventional low permeability reservoirs which are sensitive to drilling and completion damage. The work includes two test wells to be drilled by Snyder Oil Company on the Shoshone/Arapahoe Tribal Lands in the Wind River Basin. This basin is a foreland basin whose petroleum systems include Paleozoic and Cretaceous source beds and reservoirs which were buried, folded by Laramide compressional folding, and subsequently uplifted asymmetrically. The anomalous pressure boundary is also asymmetric, following differential uplift trends

Microgrid Design, Development and Demonstration - Final Report for Phase I and Phase II

Energy Technology Data Exchange (ETDEWEB)

Bose, Sumit [GE Global Research Center, Niskayuna, NY (United States); Krok, Michael [GE Global Research Center, Niskayuna, NY (United States)

2011-02-08

This document constitutes GE’s final report for the Microgrid Design, Development and Demonstration program for DOE’s Office of Electricity Delivery and Energy Reliability, Award DE-FC02-05CH11349. It contains the final report for Phase I in Appendix I, and the results the work performed in Phase II. The program goal was to develop and demonstrate a Microgrid Energy Management (MEM) framework for a broad set of Microgrid applications that provides unified controls, protection, and energy management. This project contributed to the achievement of the U.S. Department of Energy’s Renewable and Distributed Systems Integration Program goals by developing a fully automated power delivery microgrid network that: - Reduces carbon emissions and emissions of other air pollutants through increased use of optimally dispatched renewable energy, - Increases asset use through integration of distributed systems, - Enhances reliability, security, and resiliency from microgrid applications in critical infrastructure protection, constrained areas of the electric grid, etc. - Improves system efficiency with on-site, distributed generation and improved economic efficiency through demand-side management.

Practical experience and lessons learned through implementation of Appendix VIII performance demonstration requirements

International Nuclear Information System (INIS)

Ashwin, P.J.; Becker, F.L.; Latiolais, C.L.; Spanner, J.C.

1996-01-01

To provide the US nuclear industry with a uniform implementation of the Performance Demonstration requirements within the 1989 edition of ASME Section XI, Appendix VIII, representatives from all US nuclear utilities formed the Performance Demonstration Initiative (PDI). The PDI recognized the potential benefits that Appendix VIII offered the nuclear industry and initiated a proactive approach to implement the requirements. In doing so it was expected that performance demonstration of ultrasonic examination procedures would allow for improvement in the efficiency and credibility of inservice inspection to be realized. Explicit within the performance demonstration requirements of Appendix VIII is the need for a Performance Demonstration Administrator, a difficult requirement to fulfill. Not only must the administrator exhibit the attributes of understanding the demonstration requirements, but also have solid technical knowledge, integrity and be able to interface with the industry at all levels, from operations to regulatory. For the nuclear industry, the EPRI NDE Center is an obvious choice to fulfill this position. This paper provides a brief background of the PDI, a nuclear industry-wide initiative to implement the performance demonstration requirements of Appendix VIII. Even though the consensus approach adopted by the PDI is discussed, the paper's primary objective is to provide examples of the lessons learned by the Center through the specific requirements of Appendix VIII

‘Gamma Anna’: a classroom demonstration for teaching the concepts of gamma imaging

Science.gov (United States)

Wolff, Nicola; Griffiths, Jennifer; Yerworth, Rebecca

2017-01-01

Gamma imaging is at the interface of medicine and physics and thus its teaching is important in both fields. Pedagogic literature highlights the benefits of interactive demonstrations in teaching: an increase in enjoyment and interest, as well as improvement in academic achievement. However gamma imaging uses radioactive sources, which are potentially dangerous and thus their use is tightly controlled. We have developed a demonstration which uses a localised exothermic reaction within a rag doll as an analogue of radioactivity. This can be safely used in classrooms to demonstrate the principles of gamma imaging. The tool is easy to make, cheap, robust and portable. The supplementary material in this paper gives teacher notes and a description of how to make the rag doll demonstrator. We have tested the tool using six participants, acting as ‘teachers’, who carried out the demonstration and described the doll as easy to use, and the ‘tumour’ clearly identifiable. The teaching tool was separately demonstrated to a group of 12 GCSE physics students and a group of 12 medical students. Feedback showed increased student engagement, enjoyment and understanding of gamma imaging. Previous research has shown that these benefits have an impact on learning and academic outcomes.

78 FR 10610 - TRICARE; Demonstration Project for Participation in Maryland Multi-Payer Patient Centered Medical...

Science.gov (United States)

2013-02-14

... National Committee on Quality Assurance Patient Centered Medical Home (PPC-PCMH) recognition criteria... quality improvements. TMA Defense Health Cost Assessment and Evaluation (DHCAPE) staff will calculate... Maryland Multi-Payer Patient Centered Medical Home Program (MMPCMHP) Demonstration AGENCY: Department of...

The Relationship of Engagement in Improvement Practices to Outcome Measures in Large-Scale Quality Improvement Initiatives.

Science.gov (United States)

Foster, Gregory L; Kenward, Kevin; Hines, Stephen; Joshi, Maulik S

Hospital engagement networks (HENs) are part of the largest health care improvement initiative ever undertaken. This article explores whether engagement in improvement activities within a HEN affected quality measures. Data were drawn from 1174 acute care hospitals. A composite quality score was created from 10 targeted topic area measures multiplied by the number of qualifying topics. Scores improved from 5.4 (SD = 6.8) at baseline to 4.6 (5.9) at remeasurement; P improvement ( P improvement, whereas hospitals in the West ( P = .0009) did not improve as much as hospitals in other regions. After adjusting for hospital characteristics, hospitals with improvement champions ( P = .008), a higher level of engagement with their state association ( P = .001), and more leadership involvement ( P = .005) in HEN demonstrated greater improvement.

Offsite demonstrations for MWLID technologies

International Nuclear Information System (INIS)

Williams, C.; Gruebel, R.

1995-01-01

The goal of the Offsite Demonstration Project for Mixed Waste Landfill Integrated Demonstration (MWLID)-developed environmental site characterization and remediation technologies is to facilitate the transfer, use, and commercialization of these technologies to the public and private sector. The meet this goal, the project identified environmental restoration needs of mixed waste and/or hazardous waste landfill owners (Native American, municipal, DOE, and DoD); documenting potential demonstration sites and the contaminants present at each site; assessing the environmental regulations that would effect demonstration activities; and evaluating site suitability for demonstrating MWLID technologies at the tribal and municipal sites identified. Eighteen landfill sites within a 40.2-km radius of Sandia National Laboratories are listed on the CERCLIS Site/Event Listing for the state of New Mexico. Seventeen are not located within DOE or DoD facilities and are potential offsite MWLID technology demonstration sites. Two of the seventeen CERCLIS sites, one on Native American land and one on municipal land, were evaluated and identified as potential candidates for off-site demonstrations of MWLID-developed technologies. Contaminants potentially present on site include chromium waste, household/commercial hazardous waste, volatile organic compounds, and petroleum products. MWLID characterization technologies applicable to these sites include Magnetometer Towed Array, Cross-borehole Electromagnetic Imaging, SitePlanner trademark/PLUME, Hybrid Directional Drilling, Seamist trademark/Vadose Zone Monitoring, Stripping Analyses, and x-ray Fluorescence Spectroscopy for Heavy Metals

Alternative-fueled truck demonstration natural gas program: Caterpillar G3406LE development and demonstration

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-06-01

In 1990, the California Energy Commission, the South Coast Air Quality Management District, and the Southern California Gas Company joined together to sponsor the development and demonstration of compressed natural gas engines for Class 8 heavy-duty line-haul trucking applications. This program became part of an overall Alternative-Fueled Truck Demonstration Program, with the goal of advancing the technological development of alternative-fueled engines. The demonstration showed natural gas to be a technically viable fuel for Class 8 truck engines.

Solar renovation demonstration projects

Energy Technology Data Exchange (ETDEWEB)

Bruun Joergensen, O [ed.

1998-10-01

In the framework of the IEA SHC Programme, a Task on building renovation was initiated, `Task 20, Solar Energy in Building Renovation`. In a part of the task, Subtask C `Design of Solar Renovation Projects`, different solar renovation demonstration projects were developed. The objective of Subtask C was to demonstrate the application of advanced solar renovation concepts on real buildings. This report documents 16 different solar renovation demonstration projects including the design processes of the projects. The projects include the renovation of houses, schools, laboratories, and factories. Several solar techniques were used: building integrated solar collectors, glazed balconies, ventilated solar walls, transparent insulation, second skin facades, daylight elements and photovoltaic systems. These techniques are used in several simple as well as more complex system designs. (au)

Commercial incineration demonstration

International Nuclear Information System (INIS)

Borduin, L.C.; Neuls, A.S.

1981-01-01

Low-level radioactive wastes (LLW) generated by nuclear utilities presently are shipped to commercial burial grounds for disposal. Substantially increasing shipping and disposal charges have sparked renewed industry interest in incineration and other advanced volume reduction techniques as potential cost-saving measures. Repeated inquiries from industry sources regarding LLW applicability of the Los Alamos controlled-air incineration (CAI) design led DOE to initiate this commercial demonstration program in FY-1980. The selected program approach to achieving CAI demonstration at a utility site is a DOE sponsored joint effort involving Los Alamos, a nuclear utility, and a liaison subcontractor. Required development tasks and responsibilities of the particpants are described. Target date for project completion is the end of FY-1985

Memory reactivation improves visual perception.

Science.gov (United States)

Amar-Halpert, Rotem; Laor-Maayany, Rony; Nemni, Shlomi; Rosenblatt, Jonathan D; Censor, Nitzan

2017-10-01

Human perception thresholds can improve through learning. Here we report findings challenging the fundamental 'practice makes perfect' basis of procedural learning theory, showing that brief reactivations of encoded visual memories are sufficient to improve perceptual discrimination thresholds. Learning was comparable to standard practice-induced learning and was not due to short training per se, nor to an epiphenomenon of primed retrieval enhancement. The results demonstrate that basic perceptual functions can be substantially improved by memory reactivation, supporting a new account of perceptual learning dynamics.

Speed of light demonstration using Doppler beat

Science.gov (United States)

Bernal, Luis; Bilbao, Luis

2018-05-01

From an apparatus previously designed for measuring the Doppler shift using a rotating mirror, an improved, versatile version was developed for speed of light demonstrations in a classroom or a teaching laboratory. By adding a second detector and adequate beam-splitter and mirrors, three different configurations are easily assembled. One configuration is used for time-of-flight measurements between a near and a far detector, allowing one to measure the speed of light provided that the path length between detectors is known. Another variation is the interferometric method obtained by superposing the far and near signals in such a way that a minimum of the combined signal is obtained when the time delay makes the signals arrive out of phase by π radians. Finally, the standard Doppler configuration allows the measurement of the frequency beat as a function of the rotation frequency. The main advantages of the apparatus are (a) the experimental setup is simple and completely accessible to undergraduate students, (b) the light is visible, students can see the rays, which, with the use of appropriate screens, can be blocked at any point along their paths, (c) the experiment can take place entirely within the teaching laboratory or demonstration room (using the interferometric method, the shortest distance to the far mirror was as small as 0.5 m), and (d) different configurations can be built, including some economical setups within the budget of teaching laboratories.

Case Study for the ARRA-funded GSHP Demonstration at Furman University

Energy Technology Data Exchange (ETDEWEB)

Liu, Xiaobing [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Malhotra, Mini [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-11-01

With funding provided by the American Recovery and Reinvestment Act, 26 ground source heat pump (GSHP) projects were competitively selected in 2009 to demonstrate the benefits of GSHP systems and innovative technologies for cost reduction and/or performance improvement. One of the selected demonstration projects was proposed by Furman University for ten student housing buildings—the North Village located on the campus in Greeneville, South Carolina. All ten buildings are identical in floor plan and construction. Each building is conditioned by an identical GSHP system consisting of 25 water-to-air heat pump (WAHP) units, a closed-loop vertical ground heat exchanger (GHX) installed under an adjacent parking lot, and two redundant 7.5 hp variable-speed pumps to circulate water through the GHX and the WAHPs. The actual performance of the GSHP systems is analyzed with available measured data for 2014. The annual energy performance is compared with a baseline scenario in which the building is conditioned by air-source heat pumps (ASHPs) with the minimum allowed efficiencies specified in ASHRAE Standard 90.1-2013 (SEER 13 for cooling and 7.8 HSPF for heating) and supplemental electric heaters. The comparison is made in terms of energy savings, operating cost savings, cost-effectiveness, and environmental benefits. Finally, limitations in conducting this analysis are identified and recommendations for further improving the operational efficiency of the GSHP systems are made.

The Voice/Data Communications system in the Health, Education, Telecommunications Experiments. Satellite Technology Demonstration, Technical Report No. 0417.

Science.gov (United States)

Janky, James M.; And Others

The diligent use of two-way voice links via satellites substantially improves the quality and the availability of health care and educational services in remote areas. This improvement was demonstrated in several experiments that were sponsored by the Department of Health, Education, and Welfare and the National Aeronautics and Space…

Education Payload Operation - Demonstrations

Science.gov (United States)

Keil, Matthew

2009-01-01

Education Payload Operation - Demonstrations (EPO-Demos) are recorded video education demonstrations performed on the International Space Station (ISS) by crewmembers using hardware already onboard the ISS. EPO-Demos are videotaped, edited, and used to enhance existing NASA education resources and programs for educators and students in grades K-12. EPO-Demos are designed to support the NASA mission to inspire the next generation of explorers.

Regional cancer centre demonstrates voluntary conformity with the national Radiation Oncology Practice Standards.

Science.gov (United States)

Manley, Stephen; Last, Andrew; Fu, Kenneth; Greenham, Stuart; Kovendy, Andrew; Shakespeare, Thomas P

2015-06-01

Radiation Oncology Practice Standards have been developed over the last 10 years and were published for use in Australia in 2011. Although the majority of the radiation oncology community supports the implementation of the standards, there has been no mechanism for uniform assessment or governance. North Coast Cancer Institute's public radiation oncology service is provided across three main service centres on the north coast of NSW. With a strong focus on quality management, we embraced the opportunity to demonstrate conformity with the Radiation Oncology Practice Standards. The Local Health District's Clinical Governance units were engaged to perform assessments of our conformity with the standards and this was signed off as complete on 16 December 2013. The process of demonstrating conformity with the Radiation Oncology Practice Standards has enhanced the culture of quality in our centres. We have demonstrated that self-assessment utilising trained auditors is a viable method for centres to demonstrate conformity. National implementation of the Radiation Oncology Practice Standards will benefit individual centres and the broader radiation oncology community to improve the service delivered to our patients.

Regional cancer centre demonstrates voluntary conformity with the national Radiation Oncology Practice Standards

Energy Technology Data Exchange (ETDEWEB)

Manley, Stephen, E-mail: stephen.manley@ncahs.health.nsw.gov.au; Last, Andrew; Fu, Kenneth; Greenham, Stuart; Kovendy, Andrew; Shakespeare, Thomas P [North Coast Cancer Institute, Lismore, New South Wales (Australia)

2015-06-15

Radiation Oncology Practice Standards have been developed over the last 10 years and were published for use in Australia in 2011. Although the majority of the radiation oncology community supports the implementation of the standards, there has been no mechanism for uniform assessment or governance. North Coast Cancer Institute's public radiation oncology service is provided across three main service centres on the north coast of NSW. With a strong focus on quality management, we embraced the opportunity to demonstrate conformity with the Radiation Oncology Practice Standards. The Local Health District's Clinical Governance units were engaged to perform assessments of our conformity with the standards and this was signed off as complete on 16 December 2013. The process of demonstrating conformity with the Radiation Oncology Practice Standards has enhanced the culture of quality in our centres. We have demonstrated that self-assessment utilising trained auditors is a viable method for centres to demonstrate conformity. National implementation of the Radiation Oncology Practice Standards will benefit individual centres and the broader radiation oncology community to improve the service delivered to our patients.

Regional cancer centre demonstrates voluntary conformity with the national Radiation Oncology Practice Standards

International Nuclear Information System (INIS)

Manley, Stephen; Last, Andrew; Fu, Kenneth; Greenham, Stuart; Kovendy, Andrew; Shakespeare, Thomas P

2015-01-01

Radiation Oncology Practice Standards have been developed over the last 10 years and were published for use in Australia in 2011. Although the majority of the radiation oncology community supports the implementation of the standards, there has been no mechanism for uniform assessment or governance. North Coast Cancer Institute's public radiation oncology service is provided across three main service centres on the north coast of NSW. With a strong focus on quality management, we embraced the opportunity to demonstrate conformity with the Radiation Oncology Practice Standards. The Local Health District's Clinical Governance units were engaged to perform assessments of our conformity with the standards and this was signed off as complete on 16 December 2013. The process of demonstrating conformity with the Radiation Oncology Practice Standards has enhanced the culture of quality in our centres. We have demonstrated that self-assessment utilising trained auditors is a viable method for centres to demonstrate conformity. National implementation of the Radiation Oncology Practice Standards will benefit individual centres and the broader radiation oncology community to improve the service delivered to our patients

Large-scale decontamination and decommissioning technology demonstration project at a former uranium metal production facility

International Nuclear Information System (INIS)

Martineit, R.A.; Borgman, T.D.; Peters, M.S.; Stebbins, L.L.

1997-01-01

The Department of Energy's (DOE) Office of Science and Technology Decontamination and Decommissioning (D ampersand D) Focus Area, led by the Federal Energy Technology Center, has been charged with improving upon baseline D ampersand D technologies with the goal of demonstrating and validating more cost-effective and safer technologies to characterize, deactivate, survey, decontaminate, dismantle, and dispose of surplus structures, buildings, and their contents at DOE sites. The D ampersand D Focus Area's approach to verifying the benefits of the improved D ampersand D technologies is to use them in large-scale technology demonstration (LSTD) projects at several DOE sites. The Fernald Environmental Management Project (FEMP) was selected to host one of the first three LSTD's awarded by the D ampersand D Focus Area. The FEMP is a DOE facility near Cincinnati, Ohio, that was formerly engaged in the production of high quality uranium metal. The FEMP is a Superfund site which has completed its RUFS process and is currently undergoing environmental restoration. With the FEMP's selection to host an LSTD, the FEMP was immediately faced with some challenges. The primary challenge was that this LSTD was to be integrated into the FEMP's Plant 1 D ampersand D Project which was an ongoing D ampersand D Project for which a firm fixed price contract had been issued to the D ampersand D Contractor. Thus, interferences with the baseline D ampersand D project could have significant financial implications. Other challenges include defining and selecting meaningful technology demonstrations, finding/selecting technology providers, and integrating the technology into the baseline D ampersand D project. To date, twelve technologies have been selected, and six have been demonstrated. The technology demonstrations have yielded a high proportion of open-quotes winners.close quotes All demonstrated, technologies will be evaluated for incorporation into the FEMP's baseline D ampersand D

Planning a demonstration

International Nuclear Information System (INIS)

Torok, R.C.; Wilkinson, C.D.

1992-01-01

Operating nuclear power plants are increasingly recognizing the need to upgrade existing plant instrumentation and control systems to address the obsolescence of existing equipment and components. This paper reports that operating problems have provided the initial incentive for upgrading I and C systems. However, obsolescence is not the whole story. Each I and C upgrade offers the promise of improved operating performance by reducing down-time during plant outages and by implementing new features that are possible with computer-based technology. I and C upgrades using modern technology have the potential for: higher system reliability and plant availability; reductions in the number of single failure points; use of fault tolerant and self-diagnosis capabilities; improved control system stability and response time; improved accuracy of performance indictors and control signals; and a measurable reduction in operating and maintenance costs

Distributed picture compilation demonstration

Science.gov (United States)

Alexander, Richard; Anderson, John; Leal, Jeff; Mullin, David; Nicholson, David; Watson, Graham

2004-08-01

A physical demonstration of distributed surveillance and tracking is described. The demonstration environment is an outdoor car park overlooked by a system of four rooftop cameras. The cameras extract moving objects from the scene, and these objects are tracked in a decentralized way, over a real communication network, using the information form of the standard Kalman filter. Each node therefore has timely access to the complete global picture and because there is no single point of failure in the system, it is robust. The demonstration system and its main components are described here, with an emphasis on some of the lessons we have learned as a result of applying a corpus of distributed data fusion theory and algorithms in practice. Initial results are presented and future plans to scale up the network are also outlined.

DEMONSTRATION OF THE DOE INTERIM ENERGY CONSERVATION STANDARDS FOR NEW FEDERAL RESIDENTIAL BUILDINGS

Energy Technology Data Exchange (ETDEWEB)

Lee, A. D.; Baechler, H. C.; Di Massa, F. V.; Lucas, R. G.; Shankle, D. L.

1992-01-01

In accordance with federal legislation, the U.S. Department of Energy (DOE) has sponsored a study to demonstrate use of its Interim Energy Conservation Standards for New Federal Residential Buildings. The demonstration study was conducted by DOE and the Pacific Northwest Laboratory (PNL). The demonstration is the second step in a three-step process: I) development of interim standards, 2) demonstration of the interim standards, and 3) development of final standards. The standards are mandatory for federal agency housing procurements. Nevertheless, PNL found at the start of the demonstration that agency use of the interim standards had been minimal. The purpose of the standards is to improve the energy efficiency of federal housing and increase the use of nondepletable energy sources. In accordance with the legislation, the standards were to be performance-based rather than prescribing specific energy conservation measures. To fulfill this aspect of the legislation, the standards use a computer software program called COSTSAFR which generates a point system that individualizes the standards to specific projects based on climate, housing type, and fuel costs. The standards generate minimum energy-efficiency requirements by applying the life-cycle cost methodology developed for federal projects. For the demonstration, PNL and DOE chose five federal agency housing projects which had been built in diverse geographic and climate regions. Participating agencies were the Air Force, the Army (which provided two case studies), the Navy, and the Department of Health and Human Services. PNL worked with agency housing procurement officials and designers/architects to hypothetically apply the interim standards to the procurement and design of each housing project. The demonstration started at the point in the project where agencies would establish their energyefficiency requirements for the project and followed the procurement process through the designers' use of the point

Airspace Technology Demonstration 2 (ATD-2) Technology Description Document (TDD)

Science.gov (United States)

Ging, Andrew; Engelland, Shawn; Capps, Al; Eshow, Michelle; Jung, Yoon; Sharma, Shivanjli; Talebi, Ehsan; Downs, Michael; Freedman, Cynthia; Ngo, Tyler;

Total Quality Education: Profiles of Schools That Demonstrate the Power of Deming's Management Principles.

Science.gov (United States)

Schmoker, Michael J.; Wilson, Richard B.

This book presents profiles of schools that have demonstrated the power of Deming's Total Quality Management (TQM) principles. It describes schools that have successfully applied those strategies for change. The book explores what public education needs most--a compelling but flexible action plan for improvement. Chapter 1 offers a rationale for…

Demonstration of generic handbooks for assisting in the management of contaminated food production systems and inhabited areas in Europe

DEFF Research Database (Denmark)

Nisbet, A.F.; Andersson, Kasper Grann; Duranova, T.

2010-01-01

Two handbooks have been developed in conjunction with a wide range of stakeholders that provide assistance in the management of contaminated food production systems and inhabited areas following a radiological incident. Emergency centres in Member States not involved in the development...... of these handbooks were invited to take part in demonstration activities to establish whether the handbooks would be useful for the purposes of contingency planning and accident management. Some eight centres took part. Emergency exercises or similar events based on scenarios involving contamination of the foodchain...... and inhabited areas were used. Feedback from all of the demonstrations was positive with constructive criticism given on how to improve the navigation, structure and format of the handbooks. All of the key improvements highlighted during the demonstrations were taken into account and included in version 2...

[DianaWeb: a demonstration project to improve breast cancer prognosis through lifestyles].

Science.gov (United States)

Villarini, Anna; Villarini, Milena; Gargano, Giuliana; Moretti, Massimo; Berrino, Franco

2015-01-01

In the field of cancer prevention, the public ask to be involved more actively in scientific research and in the production of knowledge. This is leading to an increase of participatory projects in the field of epidemiology. Community-based participatory research (CBPR) has received considerable attention in the past 15 years; it is becoming a recognized and important approach in addressing health disparities in cancer prevention. The increasing accessibility of new methods of comparison, discussion and information allows to link a large number of people. The project DianaWeb was born in 2015 at the Department of Predictive Medicine and Prevention of the National Cancer Institute, Milan. This CBPR involves women with diagnosis of breast cancer (BC). DianaWeb communications are based on an interactive online platform developed "ad hoc" (www.dianaweb.org). With very few exceptions, all communication between participants and research team will be on the web. The recruitment is done through Internet, hospitals, physicians, media and word of mouth. Women can join the project independently, under the control of researchers and the aim of the study is to assess whether healthy eating and regular physical activity can improve the quality of life and increase survival rates in women with diagnosis of BC. About 50,000 Italian women with a diagnosis of BC with or without metastasis, local recurrence or second cancers; with in situ or invasive cancer, whatever the disease stage at diagnosis, whatever histological diagnosis, whatever the time elapsed since diagnosis should be recruited in the DianaWeb project. The volunteers are asked to send clinical information about their condition from diagnosis onwards, on their weight and other anthropometric measures, lifestyles and nutrition through online questionnaires. Moreover, the women enrolled in the study, after login, can access evidence-based information and results obtained during the project (individual and whole community

Information Integration Technology Demonstration (IITD)

National Research Council Canada - National Science Library

Loe, Richard

2001-01-01

The objectives of the Information Integration Technology Demonstration (IITD) were to investigate, design a software architecture and demonstrate a capability to display intelligence data from multiple disciplines...

Status of the Integral Fast Reactor fuel cycle demonstration and waste management practices

International Nuclear Information System (INIS)

Benedict, R.W.; Goff, K.M.; McFarlane, H.F.

1994-01-01

Over the past few years, Argonne National Laboratory has been preparing for the demonstration of the fuel cycle for the Integral Fast Reactor (IFR), an advanced reactor concept that takes advantage of the properties of metallic fuel and liquid metal cooling to offer significant improvements in reactor safety and operations, fuel-cycle economics, environmental protection, and safeguards. The IFR fuel cycle, which will be demonstrated at Argonne-West in Idaho, employs a pyrometallurgical process using molten salts and liquid metals to recover actinides from spent fuel. The required facility modifications and process equipment for the demonstration are nearing completion. Their status and the results from initial fuel fabrication work, including the waste management aspects, are presented. Additionally, estimated compositions of the various process waste streams have been made, and characterization and treatment methods are being developed. The status of advanced waste processing equipment being designed and fabricated is described

PV Cz silicon manufacturing technology improvements

Science.gov (United States)

Jester, T.

1995-09-01

This describes work done in the final phase of a 3-y, 3-phase contract to demonstrate cost reductions and improvements in manufacturing technology. The work focused on near-term projects in the SSI (Siemens Solar Industries) Czochralski (Cz) manufacturing facility in Camarillo, CA; the final phase was concentrated in areas of crystal growth, wafer technology, and environmental, safety, and health issues. During this period: (1) The crystal-growing operation improved with increased growth capacity; (2) Wafer processing with wire saws continued to progress; the wire saws yielded almost 50 percent more wafers per inch in production. The wire saws needs less etching, too; (3) Cell processing improvements focused on better handling and higher mechanical yield. The cell electrical distribution improved with a smaller standard deviation in the distribution; and (4) Module designs for lower material and labor costs continued, with focus on a new junction box, larger modules with larger cells, and less costly framing techniques. Two modules demonstrating these cost reductions were delivered during this phase.

Integrated Ground Operations Demonstration Units

Data.gov (United States)

National Aeronautics and Space Administration — The overall goal of the AES Integrated Ground Operations Demonstration Units (IGODU) project is to demonstrate cost efficient cryogenic operations on a relevant...

Biodenitrification demonstration test report

International Nuclear Information System (INIS)

Benear, A.K.; Murray, S.J.; Lahoda, E.J.; Leslie, J.W.; Patton, J.B.; Menako, C.R.

1987-08-01

A two-column biodenitrification (BDN) facility was constructed at the Feed Materials Production Center (FMPC) in 1985 and 1986 to test the feasibility of biological treatment for industrial nitrate-bearing waste water generated at FMPC. This demonstration facility comprises one-half of the proposed four-column production facility. A demonstration test was conducted over a four month period in 1987. The results indicate the proposed BDN production facility can process FMPC industrial wastewater in a continuous manner while maintaining an effluent that will consistently meet the proposed NPDES limits for combined nitrate nitrogen (NO 3 -N) and nitrite nitrogen (NO 2 -N). The proposed NPDES limits are 62 kg/day average and 124 kg/day maximum. These limits were proportioned to determine that the two-column demonstration facility should meet the limits of 31 kg/day average and 62 kg/day maximum

Waste management technology development and demonstration programs at Brookhaven National Laboratory

Science.gov (United States)

Kalb, Paul D.; Colombo, Peter

1991-01-01

Two thermoplastic processes for improved treatment of radioactive, hazardous, and mixed wastes were developed from bench scale through technology demonstration: polyethylene encapsulation and modified sulfur cement encapsulation. The steps required to bring technologies from the research and development stage through full scale implementation are described. Both systems result in durable waste forms that meet current Nuclear Regulatory Commission and Environmental Protection Agency regulatory criteria and provide significant improvements over conventional solidification systems such as hydraulic cement. For example, the polyethylene process can encapsulate up to 70 wt pct. nitrate salt, compared with a maximum of about 20 wt pct. for the best hydraulic cement formulation. Modified sulfur cement waste forms containing as much as 43 wt pct. incinerator fly ash were formulated, whereas the maximum quantity of this waste in hydraulic cement is 16 wt pct.

Sustainability Logistics Basing - Science and Technology Objective - Demonstration; Industry Assessment and Demonstration Final Report

Science.gov (United States)

2017-08-14

TECHNICAL REPORT AD ________________ NATICK/TR-17/019 SUSTAINABILITY ...LOGISTICS BASING – SCIENCE & TECHNOLOGY OBJECTIVE – DEMONSTRATION; INDUSTRY ASSESSMENT AND DEMONSTRATION FINAL REPORT by Elizabeth D. Swisher and...Benjamin J. Campbell August 2017 Final Report December 2014 – February 2016 Approved for public release; distribution is

Plug-In Hybrid Medium-Duty Truck Demonstration and Evaluation

Energy Technology Data Exchange (ETDEWEB)

Miyasato, Matt [Electric Power Research Institute (EPRI), Palo Alto, CA (United States); Kosowski, Mark [Electric Power Research Institute (EPRI), Palo Alto, CA (United States)

2015-10-01

The Plug-In Hybrid Medium-Duty Truck Demonstration and Evaluation Program was sponsored by the United States Department of Energy (DOE) using American Recovery and Reinvestment Act of 2009 (ARRA) funding. The purpose of the program is to develop a path to migrate plug-in hybrid electric vehicle (PHEV) technology to medium-duty vehicles by demonstrating and evaluating vehicles in diverse applications. The program also provided three production-ready PHEV systems—Odyne Systems, Inc. (Odyne) Class 6 to 8 trucks, VIA Motors, Inc. (VIA) half-ton pickup trucks, and VIA three-quarter-ton vans. The vehicles were designed, developed, validated, produced, and deployed. Data were gathered and tests were run to understand the performance improvements, allow cost reductions, and provide future design changes. A smart charging system was developed and produced during the program. The partnerships for funding included the DOE; the California Energy Commission (CEC); the South Coast Air Quality Management District (SCAQMD); the Electric Power Research Institute (EPRI); Odyne; VIA; Southern California Edison; and utility and municipal industry participants. The reference project numbers are DOE FOA-28 award number EE0002549 and SCAQMD contract number 10659.

Demonstration of brain tumors by computer-aided image intensification

International Nuclear Information System (INIS)

Froeder, M.; Herbst, M.; Erlangen-Nuernberg Univ., Erlangen

1987-01-01

It is possible to distinguish cerebral tumours from brain tissue after the injection of contrast by using an X-ray-video chain. Weak contrast situated behind strongly absorbing bone can be demonstrated by a non-tomographic method by reducing the noise level and by using a special subtraction technique designed for optimal iodine contrast. For this examination, four series of images are prepared and stored (one before the administration of contrast and three subsequently). Dynamic studies of the distribution of contrast in the intra- and extra-vascular spaces of brain and tumour are produced by subtracting the stored images. The demonstration of blood-flow dynamics improves the differentiation of the tumour and, in particular, makes it possible to distinguish the tumour from cerebral oedema. The current input into the X-ray tube is low and the skin dose on the entry side is less than 0.6 R for each series. The usefulness of the method in complementing computer tomography for surgical and radiation treatment is illustrated from various types of tumour. Up to the present 35 patients have been examined by this method. (orig.) [de

[Effect of comprehensive control and prevention for chronic disease in demonstration plot of Chongqing].

Science.gov (United States)

Qi, Li; Ding, Xian-bin; Mao, De-qiang; Feng, Lian-gui; Wang, Yu-lin; Jiao, Yan; Zhang, Chun-hua; Lü, Xiao-yan; Li, Hong; Xia, Yi-yin

2013-03-01

To evaluate the effect of comprehensive control and prevention for chronic diseases in demonstration plot of Chongqing. Residents were enrolled through multi-stage stratified random sampling method from 17 districts or counties which had successfully established demonstration plots and 21 districts or counties which had not established demonstration plots (non-demonstration plot for short) yet on May, 2012. Questionnaire was designed to survey awareness of health knowledge, health behaviors and utilization of health supportive tools. The results were analyzed by SPSS 15.0 software. We investigated 15 108 residents, 6156 of which were in demonstration plot and others (8951) were not. The findings revealed the percentage of the people who were aware the national action of health lifestyle in demonstration plot and in non-demonstration plot were 44.4% (2734/6157) and 40.2% (3598/8951), respectively, and the awareness of the hypertension risk of too much sodium were 72.4% (4458/6156) and 67.5% (6042/8951), respectively, and the awareness of the cardinal vascular disease (CVD) risk of obesity and overweight were 77.2% (4753/6157) and 69.6% (6230/8951), respectively. About the residents' health behaviors in demonstration plot and in non-demonstration plot, the utilization rates of salt restriction scoop or pot were 23.5% (1447/6157) and 17.9% (1602/8951), and the utilization rates of oil restriction pot were 16.7% (1028/6157) and 11.8% (1064/8951), respectively. Totally, 33 of the 37 indexes were shown higher in demonstration plot than that in non-demonstration plot (P plot was more effective, and the remarkable improvement of health knowledge and behaviors level had been achieved in demonstration plot.

Environmental process improvement feasibility study and demonstration program

Science.gov (United States)

Martin, Rodger L.

1994-01-01

This report is the final product of an environmental study conducted by Western Commercial Space Center, Inc. under contract to Tennessee-Calspan Center for Space Transportation and Applied Research. The purpose of this investigation is to accurately document the current environmental and permitting processes associated with commercial space launch activity at Vandenberg AFB, and make recommendations to streamline those processes. The particular areas of interest focus on: identifying applicable Federal, state, and local laws, Department of Defense directives, and Air force regulations; defining the environmental process on Vandenberg AFB and how it relates with other agencies, including Federal and state regulatory agencies; and defining the air quality permit process. Study investigation results are applied to an example Pilot Space Launch Vehicle (PSLV) planning to launch from Vandenberg AFB. The PSLV space hardware is analyzed with respect to environmental and permitting issues associated with vehicle processing, facilities required (existing or new), and launch. The PSLV verified the earlier findings of the study and gave insight into streamlining recommendations.

Buried Waste Integrated Demonstration Plan

International Nuclear Information System (INIS)

Kostelnik, K.M.

1991-12-01

This document presents the plan of activities for the Buried Waste Integrated Demonstration (BWID) program which supports the environmental restoration (ER) objectives of the Department of Energy (DOE) Complex. Discussed in this plan are the objectives, organization, roles and responsibilities, and the process for implementing and managing BWID. BWID is hosted at the Idaho National Engineering Laboratory (INEL), but involves participants from throughout the DOE Complex, private industry, universities, and the international community. These participants will support, demonstrate, and evaluate a suite of advanced technologies representing a comprehensive remediation system for the effective and efficient remediation of buried waste. The processes for identifying technological needs, screening candidate technologies for applicability and maturity, selecting appropriate technologies for demonstration, field demonstrating, evaluation of results and transferring technologies to environmental restoration programs are also presented. This document further describes the elements of project planning and control that apply to BWID. It addresses the management processes, operating procedures, programmatic and technical objectives, and schedules. Key functions in support of each demonstration such as regulatory coordination, safety analyses, risk evaluations, facility requirements, and data management are presented

Patient Demonstration Videos in Predoctoral Endodontic Education: Aspects Perceived as Beneficial by Students.

Science.gov (United States)

Edrees, Hadeel Y; Ohlin, Johan; Ahlquist, Michael; Tessma, Mesfin K; Zary, Nabil

2015-08-01

The aim of this study was to assess the perceived benefits of video-mediated demonstrations in learning endodontics. Participants in the study were 75 third-year students enrolled in the undergraduate dentistry program at Karolinska Institute, Stockholm, Sweden. After the endodontic preclinical course, the students were introduced to the treatment protocol in the clinic by watching two live patient-demonstrated videos. The first video demonstrated how to communicate with the patient and perform diagnosis and root canal instrumentation. The second video illustrated how to perform bacterial sampling and root canal filling. After the students watched each video, a questionnaire was used to evaluate their opinions about various steps of the endodontic treatment protocol and the benefit of such educational material for their practice. Of the total 75 students, 72 completed the first questionnaire (96% response rate), and 65 completed the second questionnaire (87% response rate). The results showed that the students perceived high value in the video demonstrations related to treatment procedure. A statistically significant difference was observed between the perceived benefits of the first and second sessions in communication and treatment procedure (p<0.001). Further studies are needed to assess improvement in the design and delivery format for video demonstrations to enhance their effectiveness as a teaching modality for endodontics.

Case study for ARRA-funded ground-source heat pump (GSHP) demonstration at Oakland University

Energy Technology Data Exchange (ETDEWEB)

Im, Piljae [ORNL; Liu, Xiaobing [ORNL

2015-09-01

High initial costs and lack of public awareness of ground-source heat pump (GSHP) technology are the two major barriers preventing rapid deployment of this energy-saving technology in the United States. Under the American Recovery and Reinvestment Act (ARRA), 26 GSHP projects have been competitively selected and carried out to demonstrate the benefits of GSHP systems and innovative technologies for cost reduction and/or performance improvement. This paper highlights the findings of a case study of one of the ARRA-funded GSHP demonstration projects, a ground-source variable refrigerant flow (GS-VRF) system installed at the Human Health Building at Oakland University in Rochester, Michigan. This case study is based on the analysis of measured performance data, maintenance records, construction costs, and simulations of the energy consumption of conventional central heating, ventilation, and air-conditioning (HVAC) systems providing the same level of space conditioning as the demonstrated GS-VRF system. The evaluated performance metrics include the energy efficiency of the heat pump equipment and the overall GS-VRF system, pumping performance, energy savings, carbon emission reductions, and cost-effectiveness of the GS-VRF system compared with conventional HVAC systems. This case study also identified opportunities for reducing uncertainties in the performance evaluation, improving the operational efficiency, and reducing the installed cost of similar GSHP systems in the future.

Demonstration of metallic implants by means of digital luminescence radiography (DLR)

International Nuclear Information System (INIS)

Wiesmann, W.; Reiser, M.; Fiebich, M.; Bick, U.; Peters, P.E.

1990-01-01

DLR makes it possible to integrate conventional radiography into digital communication and storage methods (PACS) into radiology. The use of DLR has been compared with conventional film methods in the demonstration of hip prostheses. The high contrast differences at the edge of the metal implant leads to artifacts, which could result in erroneous interpretation. Suitable image manipulation makes it possible, however, to eliminate these artifacts almost completely. DLR leads to an improvement in diagnosis in those complications not specifically related to the prostheses. (orig.) [de

MR demonstration of spontaneous acute epidural hematoma of the thoracic spine

International Nuclear Information System (INIS)

Avrahami, E.; Tadmor, R.; Feibel, M.; Itzhak, Y.; Tel Aviv Univ.; Ram, Z.; Tel Aviv Univ.

1989-01-01

Two patients with spontaneous epidural hematoma of the thoracic spine are presented. The magnetic resonance (MR) examination performed within the first hours following the onset of symptoms demonstrated an epidural elongated lesion impinging on the spinal cord, compatible with hematoma. In one of the patients this finding was surgically confirmed. The second patient improved under steroid treatment. The MR findings were highly suggestive of the pathological nature of the lesion. The MR examination should replace other diagnostic procedures, such as computerised tomography (CT) and myelography. (orig.)

Articulated inspection arm for ITER, a demonstration in the Tore Supra tokamak

Energy Technology Data Exchange (ETDEWEB)

Cordier, J.J.; Gargiulo, L.; Grisolia, C.; Samaille, F. [Association Euratom-CEA Cadarache, 13 - Saint-Paul-lez-Durance (France). Dept. de Recherches sur la Fusion Controlee; Friconneau, J.P.; Perrot, Y. [CEA Fontenay-aux-Roses, LIST Robotics and Interactive Systems Unit, 92 (France); Palmer, J.D. [Max-Planck-Institut fuer Plasmaphysik Boltzmannstr.2, Garching (Germany)

2003-07-01

The aim of this program is to demonstrate for ITER the feasibility of an in-vessel remote handling inspection using a long reach, limited payload carrier (1 to 10 kg) for penetration of the ITER chamber through the openings. This device is dedicated to close inspection of the Plasma Facing Components (PFC). An articulated demonstrator called articulated inspection arm (AIA) has been manufactured. A feasibility study of a full AIA operation in Tore Supra was performed, taking into account ITER reference requirements. A scale one demonstration of the AIA under ITER relevant condition is feasible on Tore Supra and would give significant improvement in research results for ITER remote Handling equipment. The test of the AIA demonstrator behaviour is foreseen in 2005 in real Tokamak conditions. The paper presents the full robot concept, the results of the first test campaign, the AIA new design and its integration on Tore Supra. Several potential uses of the AIA for the in vessel components inspection are being studied such as PFC visual inspection, water loop leak testing, laser ablation for wall detritiation and carbon dust and flakes removal are foreseen as utilities to be placed at the AIA head. These various systems are described in the paper.

Articulated inspection arm for ITER, a demonstration in the Tore Supra tokamak

International Nuclear Information System (INIS)

Cordier, J.J.; Gargiulo, L.; Grisolia, C.; Samaille, F.; Palmer, J.D.

2003-01-01

The aim of this program is to demonstrate for ITER the feasibility of an in-vessel remote handling inspection using a long reach, limited payload carrier (1 to 10 kg) for penetration of the ITER chamber through the openings. This device is dedicated to close inspection of the Plasma Facing Components (PFC). An articulated demonstrator called articulated inspection arm (AIA) has been manufactured. A feasibility study of a full AIA operation in Tore Supra was performed, taking into account ITER reference requirements. A scale one demonstration of the AIA under ITER relevant condition is feasible on Tore Supra and would give significant improvement in research results for ITER remote Handling equipment. The test of the AIA demonstrator behaviour is foreseen in 2005 in real Tokamak conditions. The paper presents the full robot concept, the results of the first test campaign, the AIA new design and its integration on Tore Supra. Several potential uses of the AIA for the in vessel components inspection are being studied such as PFC visual inspection, water loop leak testing, laser ablation for wall detritiation and carbon dust and flakes removal are foreseen as utilities to be placed at the AIA head. These various systems are described in the paper

Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A phenomenon of excess heat generation through the electrolysis of heavy water using palladium metals as electrode can be recognized as new hydrogen energy. Its mechanism has been investigated for four years since FY 1993. In FY 1993, the New Hydrogen Energy Demonstration Research Center and the New Hydrogen Energy Demonstration Laboratory were organized, and the research was initiated. For the excess heat generation demonstration model tests, two types of electrolysis experimental units were constructed, and the Pd/D-based electrolysis experiments were initiated. For the measurements of excess heat using an open type electrolysis cell, there were rather large errors ranging from -13% to +7%. It is necessary to improve the accuracy. For the measurements using a fuel cell type electrolysis cell, generation of the excess heat ranging from 0% to 6% was observed. For the validity of this, it is required to confirm the long-term stability of calibration and cell components. For the correlation between the increase in absorbing rate and the generation of excess heat, results of 2 to 3% lower were obtained. 28 refs., 89 figs., 26 tabs.

Simulated first operating campaign for the Integral Fast Reactor fuel cycle demonstration

International Nuclear Information System (INIS)

Goff, K.M.; Mariani, R.D.; Benedict, R.W.; Park, K.H.; Ackerman, J.P.

1993-01-01

This report discusses the Integral Fast Reactor (IFR) which is an innovative liquid-metal-cooled reactor concept that is being developed by Argonne National Laboratory. It takes advantage of the properties of metallic fuel and liquid-metal cooling to offer significant improvements in reactor safety, operation, fuel cycle-economics, environmental protection, and safeguards. Over the next few years, the IFR fuel cycle will be demonstrated at Argonne-West in Idaho. Spent fuel from the Experimental Breeder Reactor II (EBR-II) win be processed in its associated Fuel Cycle Facility (FCF) using a pyrochemical method that employs molten salts and liquid metals in an electrorefining operation. As part of the preparation for the fuel cycle demonstration, a computer code, PYRO, was developed at Argonne to model the electrorefining operation using thermodynamic and empirical data. This code has been used extensively to evaluate various operating strategies for the fuel cycle demonstration. The modeled results from the first operating campaign are presented. This campaign is capable of processing more than enough material to refuel completely the EBR-II core

Irvine Smart Grid Demonstration, a Regional Smart Grid Demonstration Project

Energy Technology Data Exchange (ETDEWEB)

Yinger, Robert [Southern California Edison Company, Rosemead, CA (United States); Irwin, Mark [Southern California Edison Company, Rosemead, CA (United States)

2015-12-29

ISGD was a comprehensive demonstration that spanned the electricity delivery system and extended into customer homes. The project used phasor measurement technology to enable substation-level situational awareness, and demonstrated SCE’s next-generation substation automation system. It extended beyond the substation to evaluate the latest generation of distribution automation technologies, including looped 12-kV distribution circuit topology using URCIs. The project team used DVVC capabilities to demonstrate CVR. In customer homes, the project evaluated HAN devices such as smart appliances, programmable communicating thermostats, and home energy management components. The homes were also equipped with energy storage, solar PV systems, and a number of energy efficiency measures (EEMs). The team used one block of homes to evaluate strategies and technologies for achieving ZNE. A home achieves ZNE when it produces at least as much renewable energy as the amount of energy it consumes annually. The project also assessed the impact of device-specific demand response (DR), as well as load management capabilities involving energy storage devices and plug-in electric vehicle charging equipment. In addition, the ISGD project sought to better understand the impact of ZNE homes on the electric grid. ISGD’s SENet enabled end-to-end interoperability between multiple vendors’ systems and devices, while also providing a level of cybersecurity that is essential to smart grid development and adoption across the nation. The ISGD project includes a series of sub-projects grouped into four logical technology domains: Smart Energy Customer Solutions, Next-Generation Distribution System, Interoperability and Cybersecurity, and Workforce of the Future. Section 2.3 provides a more detailed overview of these domains.

Demonstration of fleet trucks fueled with PV hydrogen

International Nuclear Information System (INIS)

Provenzano, J.; Scott, P.B.; Zweig, R.

1998-01-01

The Clean Air Now (CAN) Solar Hydrogen Project has been installed at the Xerox Corporation, El Segundo, California site. Three Ford Ranger trucks have been converted to use hydrogen fuel. The ''stand- alone'' electrolyzer and hydrogen dispensing system is powered by a photovoltaic array with no connection to the power grid. A variable frequency DC/AC converter steps up the voltage to drive the 15 hp motor for the hydrogen compressor. Up to 400 standard cubic meters (SCM) of solar hydrogen is stored, and storage of up to 2300 SCM of commercial hydrogen is collocated. As the hydrogen storage is within 5km of Los Angeles International Airport, pilot operation of a hydrogen fuel cell bus for airport shuttle service has been demonstrated with fueling at the CAN facility. The truck engine conversions are bored to 2.91 displacement, use a Roots type supercharger and CVI (constant volume injection) fuel induction to allow performance similar to that of the gasoline powered truck. Truck fuel storage is done with carbon composite tanks at pressures up to 24.8 MPa (3600 psi). Two tanks are located just behind the driver's cab, and take up nearly half of the truck bed space. The truck highway range is approximately 140 miles. The engine operates in lean burn mode, with nil emissions of CO and HC. NO x emissions vary with load and rpm in the range from 10 to 100 ppm, yielding total emissions at a small fraction of the ULEV standard. Two Xerox fleet trucks have been converted, and one for the City of West Hollywood. The Clean Air Now Program demonstrates that hydrogen powered fleet development is an appropriate safe, and effective strategy for improvement of urban air quality. It further demonstrates that continued technological development and cost reduction will make such implementation competitive. (Author)

ASTRID, Generation IV advanced sodium technological reactor for industrial demonstration

International Nuclear Information System (INIS)

Gauche, F.

2013-01-01

ASTRID (Advanced Sodium Technological Reactor for Industrial Demonstration) is an integrated technology demonstrator designed to demonstrate the operability of the innovative choices enabling fast neutron reactor technology to meet the Generation IV criteria. ASTRID is a sodium-cooled fast reactor with an electricity generating power of 600 MWe. In order to meet the generation IV goals, ASTRID will incorporate the following decisive innovations: -) an improved core with a very low, even negative void coefficient; -) the possible installation of additional safety devices in the core. For example, passive anti-reactivity insertion devices are explored; -) more core instrumentation; -) an energy conversion system with modular steam generators, to limit the effects of a possible sodium-water reaction, or sodium-nitrogen exchangers; -) considerable thermal inertia combined with natural convection to deal with decay heat; -)elimination of major sodium fires by bunkerization and/or inert atmosphere in the premises; -) to take into account off-site hazards (earthquake, airplane crash,...) right from the design stage; -) a complete rethink of the reactor architecture in order to limit the risk of proliferation. ASTRID will also include systems for reducing the length of refueling outages and increasing the burn-up and the duration of the cycle. In-service inspection, maintenance and repair are also taken into account right from the start of the project. The ASTRID prototype should be operational by about 2023. (A.C.)

A process for ensuring regulatory compliance at the INEL`s buried waste integrated demonstrations

Energy Technology Data Exchange (ETDEWEB)

Cannon, P.G.; Watson, L.R.; Blacker, P.B. [EG and G Idaho, Inc., Idaho Falls, ID (United States). Idaho National Engineering Lab.

1993-03-01

The Buried Waste Integrated Demonstration Program is funded by the Department of Energy Office of Technology Development. The mission of this Integrated Demonstration is to identify, evaluate, and demonstrate a suite of innovative technologies for the remediation of radioactive and hazardous waste buried throughout the DOE complex between 1950 and 1970. The program approach to development of a long-range strategy for improving buried waste remediation capabilities is to combine systems analysis with already identified remediation needs for DOE complex buried waste. The systems analysis effort has produced several configuration options (a top-level block diagram of a cradle-to-grave remediation system) capable of remediating the transuranic-contaminated waste pits and trenches at the Idaho National Engineering Laboratory. Technologies for demonstration are selected using three criteria: (a) the ability to satisfy a specific buried waste need, (b) the ability to satisfy functional and operational requirements defined for functional sub-elements in a configuration option, and (c) performance against Comprehensive Environmental Restoration and Compensation Liability Act selection criteria, such as effectiveness, implementability, and cost. Early demonstrations experienced problems with missed requirements, prompting the Buried Waste Integrated Demonstration Program Office to organize a Corrective Action Team to identify the cause and recommend corrective actions. The result of this team effort is the focus of this paper.

Cargo Data Management Demonstration System

Science.gov (United States)

1974-02-01

Delays in receipt and creation of cargo documents are a problem in international trade. The work described demonstrates some of the advantages and capabilities of a computer-based cargo data management system. A demonstration system for data manageme...

The demonstration of the auditory ossicles by high resolution CT

International Nuclear Information System (INIS)

Lloyd, G.A.S.; Boulay, G.H. du; Phelps, P.D.; Pullicino, P.

1979-01-01

The high resolution CT scanning system introduced by EMI in 1978 has added a new dimension to computerised tomography in otology. The apparatus used for this study was an EMI CT 5005 body scanner adapted for head and neck scanning and incorporating a high resolution facility. The latter has proved most advantageous in areas of relatively high differential absorption, so that its application to the demonstration of abnormalities in the petrous temporal bone, and in particular middle ear disease, has been very rewarding. Traumatic ossicular disruptions may now be demonstrated and the high contrast of CT often shows them better than conventional hypocycloidal tomography. The stapes is also better visualised and congenital abnormalities of its superstructure have been recorded. These studies have been achieved with a very acceptable level of radiation to the eye, lens and cornea and the technique is clearly a rival to conventional pluridirectional tomography in the assessment of the petrous temporal bone. With further design improvements high resolution CT could completely replace existing techniques. (orig.) [de

Auditory demonstrations simulating Mayan architecture

Science.gov (United States)

Lubman, David

2005-09-01

Fascination with the ancient temples and ball court at Chichen Itza provide rich opportunities for science education. Children of all ages are delighted to learn that the sound of handclaps scattered from long temple staircases are transformed into bird chirps. Their engagement in such seemingly magical phenomena provides magic moments for teaching acoustical principals, including the picket-fence effect (PFE). PFE transforms impulsive sounds scattered from spatially periodic structures into tonal sounds. PFE is demonstrated with a computer possessing a sound card and a simple sound editing program. The inverse relationship between tonal frequency and the time interval between periodic impulses is easily demonstrated. The number of impulses needed to produce an audible tone is easily demonstrated and compared with the number of steps on the staircase. Transformation of audible tones into downward-gliding chirps is simulated by monotonically increasing the time between impulses. The Great Ball Court also provides opportunities for acoustical demonstration. Observers clapping their hands while standing between the long, tall, and parallel walls of the playing field marvel at the profound flutter echo heard for about 1.5 s. The flutter echo sonogram demonstrates the speed of sound and frequency-selective atmospheric attenuation.

Testing, development and demonstration of large scale solar district heating systems

DEFF Research Database (Denmark)

Furbo, Simon; Fan, Jianhua; Perers, Bengt

2015-01-01

In 2013-2014 the project “Testing, development and demonstration of large scale solar district heating systems” was carried out within the Sino-Danish Renewable Energy Development Programme, the so called RED programme jointly developed by the Chinese and Danish governments. In the project Danish...... know how on solar heating plants and solar heating test technology have been transferred from Denmark to China, large solar heating systems have been promoted in China, test capabilities on solar collectors and large scale solar heating systems have been improved in China and Danish-Chinese cooperation...

How business intelligence can improve value.

Science.gov (United States)

Moore, Keith D; Eyestone, Katie; Coddington, Dean C

2012-10-01

Case studies of three healthcare organizations reinforce the premise that business intelligence--the ability to convert data into actionable information for decision making--is critical to demonstrating improved value.

Advancing the US Department of Energy's Technologies through the Underground Storage Tank: Integrated Demonstration Program

International Nuclear Information System (INIS)

Gates, T.E.

1993-01-01

The principal objective of the Underground Storage Tank -- Integrated Demonstration Program is the demonstration and continued development of technologies suitable for the remediation of waste stored in underground storage tanks. The Underground Storage Tank Integrated Demonstration Program is the most complex of the integrated demonstration programs established under the management of the Office of Technology Development. The Program has the following five participating sites: Oak Ridge, Idaho, Fernald, Savannah River, and Hanford. Activities included within the Underground Storage Tank -- Integrated Demonstration are (1) characterizating radioactive and hazardous waste constituents, (2) determining the need and methodology for improving the stability of the waste form, (3) determining the performance requirements, (4) demonstrating barrier performance by instrumented field tests, natural analog studies, and modeling, (5) determining the need and method for destroying and stabilizing hazardous waste constituents, (6) developing and evaluating methods for retrieving, processing (pretreatment and treatment), and storing the waste on an interim basis, and (7) defining and evaluating waste packages, transportation options, and ultimate closure techniques including site restoration. The eventual objective is the transfer of new technologies as a system to full-scale remediation at the US Department of Energy complexes and sites in the private sector

Prototype scale demonstration of CECE detritiation

International Nuclear Information System (INIS)

Sadhankar Ramesh; Cobanoglu, Macit

2004-01-01

AECL has developed and demonstrated the Combined Electrolysis and Catalytic Exchange (CECE) Process for detritiation of heavy water. Although CECE has been the subject of pilot-scale demonstrations by various organizations, AECL is the first to demonstrate this technology in an industrial prototype plant. AECL designed, built and operated a CECE demonstration facility under CAN/CSA N286 Quality Assurance Program. The facility was licensed by the Canadian nuclear regulator. This was a two-fold demonstration of the CECE technology - for upgrading (removal of light water) and for detritiation of heavy water. In 1998 June, AECL began operating the facility in upgrading mode. The design feed rate ranged up to 25 Mg/a for 95 mol% D 2 O feed water. After 18 months of operation in upgrading mode, the facility was reconfigured and operated for an additional 9 months from 2000 August in detritiation mode. Design capacity for detritiation was 5 Mg/a with a detritiation factor (DF) of 100. However, significantly higher DFs, up to 56 000, were demonstrated. Highlights of the detritiation demonstration were: Proven robustness of AECL's proprietary wetproofed catalyst for Liquid Phase Catalytic Exchange; Demonstration of a trickle-bed-recombiner for stoichiometric combination of deuterium and oxygen; Demonstration of electrolysis of highly tritiated heavy water; High process availability and controllability was demonstrated by a long interrupted run; Low emissions; Demonstration of high DF - up to 56 000 - a significant advantage of the CECE process over other approaches to detritiation; Validation of AECL's simulation code for the CECE process over a range of DFs from 100 to 50 000. Apart from the technology, AECL has expertise in all aspects of setting up a new detritiation facility including design, engineering, safety assessment, licensing support, project management and training. AECL is also the engineering and design contractor for a tritium removal facility that is under

A study on development of Pyro process integrated inactive demonstration facility

International Nuclear Information System (INIS)

Cho, I.; Lee, E.; Choung, W.; You, G.; Kim, H.

2010-10-01

Since 2007, the Pride (Pyro process integrated inactive demonstration facility) has been developed to demonstrate the integrated engineering-scale pyro processing using natural uranium with surrogate materials. In this paper, safety evaluation on hypothetical accident case is carried out to ensure the release of radioactivity being negligible to the environment and the performance of indoor argon flow for the argon cell has been investigated by means of CFD analysis. The worst accident case, even in the firing of the all uranium metal in argon cell, cause dose rate are negligible comparing to 0.25 Sv of effective dose rate to whole body or 3 Sv of equivalent dose rate to the thyroid preliminary CFD analyses show the temperature and velocity distribution of argon cell, and give the information to change the argon exchange rate and displace the argon supply or exhaust duct. CFD will allow design change and improvements in ventilation systems at lower cost. (Author)

[Evaluation on intervention measures of comprehensive control for parasitic diseases in demonstration plot of Xiangyun County].

Science.gov (United States)

Wen-Juan, Li; Shao-Rong, Chen; Yan-Hong, Li; Wen, Fang; Chun-Rong, Ke; Li-Bo, Wang

2011-10-01

To evaluate the effect of comprehensive intervention measures to control and prevent parasitic diseases in the demonstration plot of Xiangyun County, so as to provide the evidence for establishing appropriate measures of parasitic diseases control and prevention. The baseline data of soil-transmitted nematode infections were obtained in 2006. A series of intervention measures, including health education, deworming, drinking water improvement,latrine improvement, and environment reconstruction, were performed for three years and the effect of the comprehensive intervention measures was evaluated by the national expert group in 2009. The awareness rate of parasitic disease knowledge of residents in 2009 (86.96%) was significantly higher than that in 2006 (35.20%) (Chi2 = 122.95, P transmitted nematode infections, the infection rates of Ascaris lumbricoides in both 2006 and 2009 were the highest and the rates were 18.74% and 2.08%, respectively. In the demonstration plots for parasitic diseases control and prevention of Xiangyun County, the effect of the comprehensive intervention measures which take health education as the forerunner and give priority to control source of parasite infection is remarkable. The measures implemented can achieve the purpose to reduce the infection rates of parasites and improve human health.

40 CFR 117.14 - Demonstration projects.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 21 2010-07-01 2010-07-01 false Demonstration projects. 117.14 Section... DETERMINATION OF REPORTABLE QUANTITIES FOR HAZARDOUS SUBSTANCES Applicability § 117.14 Demonstration projects... research or demonstration projects relating to the prevention, control, or abatement of hazardous substance...

Demonstration of a repository performance assessment capability at the US Nuclear Regulatory Commission

International Nuclear Information System (INIS)

Codell, R.; Eisenberg, N.; McCartin, T.; Park, J.

1991-01-01

In order to better review licensing submittals for a High-Level Waste Repository, the US Nuclear Regulatory Commission staff has expanded and improved its capability to conduct performance assessments. A demonstration of this capability used the limited data from Yucca Mountain, Nevada to investigate a small set of scenario classes. Models of release and transport of radionuclides from a repository via the groundwater and direct release pathways provided preliminary estimates of releases to the accessible environment for a 10,000 year simulation time. Latin hypercube sampling of input parameters was used to express results as distributions and to investigate model sensitivities. This methodology demonstration should not be interpreted as an estimate of performance of the proposed repository at Yucca Mountain, Nevada

Safety demonstration test (SR-1/S1C-1) plan of HTTR (Contract research)

Energy Technology Data Exchange (ETDEWEB)

Nakagawa, Shigeaki; Sakaba, Nariaki; Takada, Eiji; Tachibana, Yukio; Saito, Kenji; Furusawa, Takayuki; Sawa, Kazuhiro [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment

2003-03-01

Safety demonstration tests in the HTTR (High Temperature Engineering Test Reactor) will be carried out in order to verify inherent safety features of the HTGR (High Temperature Gas-cooled Reactor). The first phase of the safety demonstration tests includes the reactivity insertion test by the control rod withdrawal and the coolant flow reduction test by the circulator trip. In the second phase, accident simulation tests will be conducted. By comparison of their experimental and analytical results, the prediction capability of the safety evaluation codes such as the core and the plant dynamics codes will be improved and verified, which will contribute to establish the safety design and the safety evaluation technologies of the HTGRs. The results obtained through its safety demonstration tests will be also utilised for the establishment of the safety design guideline, the safety evaluation guideline, etc. This paper describes the test program of the overall safety demonstration tests and the test method, the test conditions and the results of the pre-test analysis of the reactivity insertion test and the partial gas circulator trip test planned in March 2003. (author)

Evolution and outcomes of a quality improvement program.

Science.gov (United States)

Thor, Johan; Herrlin, Bo; Wittlöv, Karin; Øvretveit, John; Brommels, Mats

2010-01-01

The purpose of this paper is to examine the outcomes and evolution over a five-year period of a Swedish university hospital quality improvement program in light of enduring uncertainty regarding the effectiveness of such programs in healthcare and how best to evaluate it. The paper takes the form of a case study, using data collected as part of the program, including quality indicators from clinical improvement projects and participants' program evaluations. Overall, 58 percent of the program's projects (39/67) demonstrated success. A greater proportion of projects led by female doctors demonstrated success (91 percent, n=11) than projects led by male doctors (51 percent, n=55). Facilitators at the hospital continuously adapted the improvement methods to the local context. A lack of dedicated time for improvement efforts was the participants' biggest difficulty. The dominant benefits included an increased ability to see the "bigger picture" and the improvements achieved for patients and employees. Quality measurement, which is important for conducting and evaluating improvement efforts, was weak with limited reliability. Nevertheless, the present study adds evidence about the effectiveness of healthcare improvement programs. Gender differences in improvement team leadership merit further study. Improvement program evaluation should assess the extent to which improvement methods are locally adapted and applied. This case study reports the outcomes of all improvement projects undertaken in one healthcare organization over a five-year period and provides in-depth insight into an improvement program's changeable nature.

Case Study of The ARRA-Funded GSHP Demonstration at the Natural Sources Building, Montana Tech

Energy Technology Data Exchange (ETDEWEB)

Malhotra, Mini [ORNL; Liu, Xiaobing [ORNL

2015-04-01

Under the American Recovery and Reinvestment Act (ARRA), 26 ground source heat pump (GSHP) projects were competitively selected in 2009 to demonstrate the benefits of GSHP systems and innovative technologies for cost reduction and/or performance improvement. One of the selected demonstration projects was proposed by Montana Tech of the University of Montana for a 56,000 sq ft, newly constructed, on-campus research facility – the Natural Resources Building (NRB) located in Butte, Montana. This demonstrated GSHP system consists of a 50 ton water-to-water heat pump and a closed-loop ground heat exchanger with two redundant 7.5 hp constant-speed pumps to use water in the nearby flooded mines as a heat source or heat sink. It works in conjunction with the originally installed steam HX and an aircooled chiller to provide space heating and cooling. It is coupled with the existing hot water and chilled water piping in the building and operates in the heating or cooling mode based on the outdoor air temperature. The ground loop pumps operate in conjunction with the existing pumps in the building hot and chilled water loops for the operation of the heat pump unit. The goal of this demonstration project is to validate the technical and economic feasibility of the demonstrated commercial-scale GSHP system in the region, and illustrate the feasibility of using mine waters as the heat sink and source for GSHP systems. Should the demonstration prove satisfactory and feasible, it will encourage similar GSHP applications using mine water, thus help save energy and reduce carbon emissions. The actual performance of the system is analyzed with available measured data for January through July 2014. The annual energy performance is predicted and compared with a baseline scenario, with the heating and cooling provided by the originally designed systems. The comparison is made in terms of energy savings, operating cost savings, cost-effectiveness, and environmental benefits. Finally

CALDERON COKEMAKING PROCESS/DEMONSTRATION PROJECT

International Nuclear Information System (INIS)

Albert Calderon

1998-01-01

This project deals with the demonstration of a coking process using proprietary technology of Calderon, with the following objectives geared to facilitate commercialization: (1) making coke of such quality as to be suitable for use in hard-driving, large blast furnaces; (2) providing proof that such process is continuous and environmentally closed to prevent emissions; (3) demonstrating that high-coking-pressure (non-traditional) coal blends which cannot be safely charged into conventional by-product coke ovens can be used in the Calderon process; and (4) demonstrating that coke can be produced economically, at a level competitive with coke imports. The activities of the past quarter were focused on the following: Conducting bench-scale tests to produce coke and acceptable tar from the process to satisfy Koppers, a prospective stakeholder; Consolidation of the project team players to execute the full size commercial cokemaking reactor demonstration; and Progress made in advancing the design of the full size commercial cokemaking reactor

Demonstration of Cauchy: Understanding Algebraic

Directory of Open Access Journals (Sweden)

T.L. Costa

2012-11-01

Full Text Available ABSTRACT: In this study we present some considerations about the End of Course Work undergraduate Full Degree in Mathematics / UFMT, drafted in 2011, and by taking title "A story about Cauchy and Euler's theorem on polyhedra" that gave birth to our research project Master of Education, begun in 2012, on the approaches of Euler's theorem on polyhedra in mathematics textbooks. At work in 2011 presented some considerations about the history of Euler's theorem for polyhedra which focus the demonstration presented by Cauchy (1789-1857, who tries to generalize it, relying on assumptions not observable in Euclidean geometry. Therefore, we seek the accessible literature on the history of mathematics; relate some aspects of the demonstration Cauchy with historical events on the development of mathematics in the nineteenth century, which allowed the acceptance of such a demonstration by mathematicians of his time.Keywords: History of Mathematics. Euler's Theorem on Polyhedra. Demonstration of Cauchy.

CALDERON COKEMAKING PROCESS/DEMONSTRATION PROJECT

International Nuclear Information System (INIS)

Albert Calderon

1999-01-01

This project deals with the demonstration of a coking process using proprietary technology of Calderon, with the following objectives geared to facilitate commercialization: (1) making coke of such quality as to be suitable for use in hard-driving, large blast furnaces; (2) providing proof that such process is continuous and environmentally closed to prevent emissions; (3) demonstrating that high-coking-pressure (non-traditional) coal blends which cannot be safely charged into conventional by-product coke ovens can be used in the Calderon process; and (4) demonstrating that coke can be produced economically, at a level competitive with coke imports. The activities of the past quarter were focused on the following: Consolidation of the team of stakeholders; Move the site for the commercial demonstration to LTV Steel, Cleveland, Ohio; Permitting for new site; Site specific engineering; Cost update of the project as it relates to the Cleveland location; FETC update; DCAA audit; and Updated endorsement of Calderon process by Ohio EPA and U.S. EPA, Region 5

Mindtagger: A Demonstration of Data Labeling in Knowledge Base Construction.

Science.gov (United States)

Shin, Jaeho; Ré, Christopher; Cafarella, Michael

2015-08-01

End-to-end knowledge base construction systems using statistical inference are enabling more people to automatically extract high-quality domain-specific information from unstructured data. As a result of deploying DeepDive framework across several domains, we found new challenges in debugging and improving such end-to-end systems to construct high-quality knowledge bases. DeepDive has an iterative development cycle in which users improve the data. To help our users, we needed to develop principles for analyzing the system's error as well as provide tooling for inspecting and labeling various data products of the system. We created guidelines for error analysis modeled after our colleagues' best practices, in which data labeling plays a critical role in every step of the analysis. To enable more productive and systematic data labeling, we created Mindtagger, a versatile tool that can be configured to support a wide range of tasks. In this demonstration, we show in detail what data labeling tasks are modeled in our error analysis guidelines and how each of them is performed using Mindtagger.

Remote monitoring demonstration

International Nuclear Information System (INIS)

Caskey, Susan; Olsen, John

2006-01-01

The recently upgraded remote monitoring system at the Joyo Experimental Reactor uses a DCM-14 camera module and GEMINI software. The final data is compatible both with the IAEA-approved GARS review software and the ALIS software that was used for this demonstration. Features of the remote monitoring upgrade emphasized compatibility with IAEA practice. This presentation gives particular attention to the selection process for meeting network security considerations at the O'arai site. The Joyo system is different from the NNCA's ACPF system, in that it emphasizes use of IAEA standard camera technology and data acquisition and transmission software. In the demonstration itself, a temporary virtual private network (VPN) between the meeting room and the server at Sandia in Albuquerque allowed attendees to observe data stored from routine transmissions from the Joyo Fresh Fuel Storage to Sandia. Image files from a fuel movement earlier in the month showed Joyo workers and IAEA inspectors carrying out a transfer. (author)

Photovoltaic demonstration projects

Energy Technology Data Exchange (ETDEWEB)

Kaut, W [Commission of the European Communities, Brussels (Belgium); Gillett, W B; Hacker, R J [Halcrow Gilbert Associates Ltd., Swindon (GB)

1992-12-31

This publication, comprising the proceedings of the fifth contractor`s meeting organized by the Commission of the European Communities, Directorate-General for Energy, provides an overview of the photovoltaic demonstration projects which have been supported in the framework of the energy demonstration programme since 1983. It includes reports by each of the contractors who submitted proposals in 1987 and 1988, describing progress within their projects. Projects accepted from earlier calls for proposals and not yet completed were reviewed by a rapporteur and are discussed in the summary section. The results of the performance monitoring of all projects and the lessons drawn from the practical experience of the projects are also presented in the summaries and conclusions. Contractors whose projects were submitted in 1989 were also present at the meeting and contributed to the reported discussions. This proceeding is divided into four sessions (General, Housing, technical presentations, other applications) and 24 papers are offered.

AVNG system demonstration

Energy Technology Data Exchange (ETDEWEB)

Thron, Jonathan Louis [Los Alamos National Laboratory; Mac Arthur, Duncan W [Los Alamos National Laboratory; Kondratov, Sergey [VNIIEF; Livke, Alexander [VNIIEF; Razinkov, Sergey [VNIIEF

2010-01-01

An attribute measurement system (AMS) measures a number of unclassified attributes of potentially classified material. By only displaying these unclassified results as red or green lights, the AMS protects potentially classified information while still generating confidence in the measurement result. The AVNG implementation that we describe is an AMS built by RFNC - VNIIEF in Sarov, Russia. To provide additional confidence, the AVNG was designed with two modes of operation. In the secure mode, potentially classified measurements can be made with only the simple red light/green light display. In the open mode, known unclassified material can be measured with complete display of the information collected from the radiation detectors. The AVNG demonstration, which occurred in Sarov, Russia in June 2009 for a joint US/Russian audience, included exercising both modes of AVNG operation using a number of multi-kg plutonium sources. In addition to describing the demonstration, we will show photographs and/or video taken of AVNG operation.

42 CFR 494.110 - Condition: Quality assessment and performance improvement.

Science.gov (United States)

2010-10-01

... facility must maintain and demonstrate evidence of its quality improvement and performance improvement... RENAL DISEASE FACILITIES Patient Care § 494.110 Condition: Quality assessment and performance improvement. The dialysis facility must develop, implement, maintain, and evaluate an effective, data-driven...

A tool for safety evaluations of road improvements.

Science.gov (United States)

Peltola, Harri; Rajamäki, Riikka; Luoma, Juha

2013-11-01

Road safety impact assessments are requested in general, and the directive on road infrastructure safety management makes them compulsory for Member States of the European Union. However, there is no widely used, science-based safety evaluation tool available. We demonstrate a safety evaluation tool called TARVA. It uses EB safety predictions as the basis for selecting locations for implementing road-safety improvements and provides estimates of safety benefits of selected improvements. Comparing different road accident prediction methods, we demonstrate that the most accurate estimates are produced by EB models, followed by simple accident prediction models, the same average number of accidents for every entity and accident record only. Consequently, advanced model-based estimates should be used. Furthermore, we demonstrate regional comparisons that benefit substantially from such tools. Comparisons between districts have revealed significant differences. However, comparisons like these produce useful improvement ideas only after taking into account the differences in road characteristics between areas. Estimates on crash modification factors can be transferred from other countries but their benefit is greatly limited if the number of target accidents is not properly predicted. Our experience suggests that making predictions and evaluations using the same principle and tools will remarkably improve the quality and comparability of safety estimations. Copyright © 2013 Elsevier Ltd. All rights reserved.

Demonstration Project. Consumer reactions to peak prices

International Nuclear Information System (INIS)

Lindskoug, Stefan

2006-06-01

The purpose and aim of the project is to look at the risk of capacity shortage in the Swedish electricity supply system during excessively cold periods of weather. A risk that has increased in recent years. A growing number of analysts emphasize the importance of high spot prices actually leading to a reduction in demand. Through increased consumer sensitivity as regards pricing, the power system can be run safely with smaller generation reserves. In addition, market price fluctuation is estimated to become more stable and predictable. The purpose of the Demonstration Project is to demonstrate methods or business concepts that lead to the demand for electricity on a national level being reduced at times of high spot prices. The need for the measures to be profitable for the parties involved is an important starting point. A general problem associated with research and development projects is that the participants feel selected and special attention is paid them, hence they will make an extra effort to improve the results. We were aware of this fact when setting up the trials, which is why we introduced the trials as an offer from the electricity supplier to take part in a commercial assessment using a new price list. For this reason we concealed the marked research aim with Elforsk as a backer. Evaluating the results of questionnaires and detailed interviews does not give cause to suppose the results are in any way affected by such conditions. The conclusion of this project is that controlling load at the customer end is an economic alternative to the investment of new production resources

PHARUS ASAR demonstrator

NARCIS (Netherlands)

Smith, A.J.E.; Bree, R.J.P. van; Calkoen, C.J.; Dekker, R.J.; Otten, M.P.G.; Rossum, W.L. van

2001-01-01

PHARUS is a polarimetric phased array C-band Synthetic Aperture Radar (SAR), designed and built for airborne use. Advanced SAR (ASAR) data in image and alternating polarization mode have been simulated with PHARUS to demonstrate the use of Envisat for a number of typical SAR applications that are

Gigashot Optical Laser Demonstrator

Energy Technology Data Exchange (ETDEWEB)

Deri, R. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2015-10-13

The Gigashot Optical Laser Demonstrator (GOLD) project has demonstrated a novel optical amplifier for high energy pulsed lasers operating at high repetition rates. The amplifier stores enough pump energy to support >10 J of laser output, and employs conduction cooling for thermal management to avoid the need for expensive and bulky high-pressure helium subsystems. A prototype amplifier was fabricated, pumped with diode light at 885 nm, and characterized. Experimental results show that the amplifier provides sufficient small-signal gain and sufficiently low wavefront and birefringence impairments to prove useful in laser systems, at repetition rates up to 60 Hz.

BWR Servicing and Refueling Improvement Program: Phase I summary report

Energy Technology Data Exchange (ETDEWEB)

Perry, D.R.

1978-09-01

Under the U.S. Department of Energy sponsorship, General Electric Co. (GE) undertook a study of boiling water reactor (BWR) refueling outages for the purpose of recommending the development and demonstration of critical path time savings improvements. The Tennessee Valley Authority (TVA) joined the study as a subcontractor, providing monitoring assistance and making the Browns Ferry Site available for improvement demonstrations. Agreement was also reached with Georgia Power Co., Power Authority of the State of New York, and Commonwealth Edison Co. for monitoring and data collection at Hatch 1, FitzPatrick, and Quad Cities 1 nuclear plants, respectively. The objective was to identify, develop, and demonstrate improved refueling, maintenance, and inspection procedures and equipment. The improvements recommended in this study are applicable to BWR nuclear plants currently in operation as well as those in the design and construction phases. The recommendations and outage information can be used as a basis to plan and conduct the first outages of new plants and to improve the planning and facilities of currently operating plants. Many of the recommendations can readily be incorporated in plants currently in the design and construction phases as well as in the design of future plants. Many of these recommended improvements can be implemented immediately by utilities without further technical development.

BWR Servicing and Refueling Improvement Program: Phase I summary report

International Nuclear Information System (INIS)

Perry, D.R.

1978-09-01

Under the U.S. Department of Energy sponsorship, General Electric Co. (GE) undertook a study of boiling water reactor (BWR) refueling outages for the purpose of recommending the development and demonstration of critical path time savings improvements. The Tennessee Valley Authority (TVA) joined the study as a subcontractor, providing monitoring assistance and making the Browns Ferry Site available for improvement demonstrations. Agreement was also reached with Georgia Power Co., Power Authority of the State of New York, and Commonwealth Edison Co. for monitoring and data collection at Hatch 1, FitzPatrick, and Quad Cities 1 nuclear plants, respectively. The objective was to identify, develop, and demonstrate improved refueling, maintenance, and inspection procedures and equipment. The improvements recommended in this study are applicable to BWR nuclear plants currently in operation as well as those in the design and construction phases. The recommendations and outage information can be used as a basis to plan and conduct the first outages of new plants and to improve the planning and facilities of currently operating plants. Many of the recommendations can readily be incorporated in plants currently in the design and construction phases as well as in the design of future plants. Many of these recommended improvements can be implemented immediately by utilities without further technical development

Technical Note: Asteroid Detection Demonstration from SkySat-3 - B612 Data Using Synthetic Tracking

Science.gov (United States)

Zhai, C.; Shao, M.; Lai, S.; Boerner, P.; Dyer, J.; Lu, E.; Reitsema, H.; Buie, M.

2018-01-01

We report results from analyzing the data taken by the sCMOS cameras on board of SkySat3 using the synthetic tracking technique. The analysis demonstrates the expected sensitivity improvement in the signal-to-noise ratio of the faint asteroids from properly stacking up the short exposure images in post-processing.

Optics Demonstrations Using Cylindrical Lenses

Science.gov (United States)

Ivanov, Dragia; Nikolov, Stefan

2015-01-01

In this paper we consider the main properties of cylindrical lenses and propose several demonstrational experiments that can be performed with them. Specifically we use simple glasses full of water to demonstrate some basic geometrical optics principles and phenomena. We also present some less standard experiments that can be performed with such…

A Comprehensive General Chemistry Demonstration

Science.gov (United States)

Sweeder, Ryan D.; Jeffery, Kathleen A.

2013-01-01

This article describes the use of a comprehensive demonstration suitable for a high school or first-year undergraduate introductory chemistry class. The demonstration involves placing a burning candle in a container adjacent to a beaker containing a basic solution with indicator. After adding a lid, the candle will extinguish and the produced…

Human Resource Management for Continuous Improvement

DEFF Research Database (Denmark)

Jørgensen, Frances; Laugen, Bjørge Timenes; Boer, Harry

2007-01-01

This paper investigates the relationship between HRM practices and Continuous Improvement (CI) activities in order to gain an understanding of how the HRM function may be utilized to improve CI implementation success, and consequently, company performance. The paper begins with a brief review...... of the HRM and CI literature and then presents statistical analyses of data collected from the Continuous Improvement Network Survey (2003), which demonstrate that HRM has a significant effect on CI behaviour and company performance, with the strongest relationship between HRM, CI and performance occurring...

Large-scale demonstration of reliability centered maintenance at two nuclear generating stations

International Nuclear Information System (INIS)

Gaertner, J.P.; Edgar, C.; Rodin, M.E.

1989-01-01

This paper reports that after successful single-system pilot applications of Reliability Centered Maintenance (RCM) at various utilities, EPRI with Rochester Gas and Electric and Southern California Edison is undertaking multiple-system applications of RCM at their respective nuclear plants. The objective is to demonstrate the feasibility and cost-effectiveness of large-scale RCM application. In addition, each utility has plant-specific objectives to improve maintenance and plant availability. Each project has selected a prioritized list of some 15-20 systems on which to perform RCM. Each project is employing somewhat different RCM analysis methods, both of which conform to a global RCM definition applicable to all EPRI RCM work to date. Each project has developed important insights for improving cost and value of future analyses. Both projects will have applied the RCM process, including implementation, on several plant systems by April 1989

NDT performance demonstration in Spain

International Nuclear Information System (INIS)

Bollini, G.J.

1994-01-01

The experience obtained from the in-service inspection of reactor pressure vessels (RPV) of Spanish nuclear power plants and the participation in several international programs, such as PISC, has shown the need for a performance demonstration, not only for the ultrasonic inspection techniques of RPV, but also for other ISI non-destructive techniques as in the case of eddy current inspection of steam generator tubing. Section XI of the ASME Code, which is applied in Spain for ISI, has incorporated recently the Appendix VIII for performance demonstration of ultrasonic inspection techniques. As a direct consequence of this, a Spanish project for performance demonstration of ultrasonic inspection techniques has been launched recently, which includes the manufacturing of full-scale mock-ups of nozzle to vessel welds, reactor vessel welds, wrought austenitic piping welds and ferritic piping welds of PWR and BWR nuclear power plants from different suppliers. This considerable technical effort will let the different Spanish organizations which are part of the project to participate and colaborate with similar international projects and in particular with a European initiative for performance demonstration. (Author)

Small recuperated ceramic microturbine demonstrator concept

International Nuclear Information System (INIS)

McDonald, Colin F.; Rodgers, Colin

2008-01-01

It has been about a decade since microturbines first entered service in the distributed generation market, and the efficiencies of these turbogenerators rated in the 30-100 kW power range have remained essentially on the order of 30%. In this time frame the cost of fuel (natural gas and oil) has increased substantially, and efforts are now underway to increase the efficiency of microturbines to 40% or higher. Various near-term means of achieving this are underway by utilizing established gas turbine technology, but now based on more complex thermodynamic cycles. A longer-term approach of improving efficiency is proposed in this paper based on the retention of the basic recuperated Brayton cycle, but now operating at significantly higher levels of turbine inlet temperature. However, in small low pressure ratio recuperated microturbines embodying radial flow turbomachinery this necessitates the use of ceramic components, including the turbine, recuperator and combustor. A development approach is proposed to design, fabricate and test a 7.5 kW ceramic microturbine demonstrator concept, which for the first time would involve the coupling of a ceramic radial flow turbine, a ceramic combustor, and a compact ceramic fixed-boundary high effectiveness recuperator. In a period of some three years, the major objectives of the proposed small ceramic microturbine R and D effort would be to establish a technology base involving thermal and stress analysis, design methodology, ceramic component fabrication techniques, and component development, these culminating in the assembly and testing to demonstrate engine structural integrity, and to verify performance. This would provide a benchmark for more confidently advancing to increased size ceramic-based turbogenerators with the potential for efficiencies of over 40%. In addition, the power size of the tested prototype could possibly emerge as a viable product, namely as a natural gas-fired turbogenerator with the capability of

Improving Exclusive Breastfeeding in an Urban Academic Hospital.

Science.gov (United States)

Ward, Laura P; Williamson, Susan; Burke, Stephanie; Crawford-Hemphill, Ruby; Thompson, Amy M

2017-02-01

Breastfeeding has many well-established health benefits for infants and mothers. There is greater risk reduction in health outcomes with exclusive breastfeeding (EBF). Our urban academic facility has had long-standing low EBF rates, serving a population with breastfeeding disparities. We sought to improve EBF rates through a Learning Collaborative model by participating in the Best Fed Beginnings project. Formal improvement science methods were used, including the development of a key driver diagram and plan-do-study-act cycles. Improvement activities followed the Ten Steps to Successful Breastfeeding. We demonstrated significant improvement in the median adherence to 2 process measures, rooming in and skin-to-skin after delivery. Subsequently, the proportion of infants exclusively breastfed at hospital discharge in our facility increased from 37% to 59%. We demonstrated an increase in sustained breastfeeding in a subset of patients at a postpartum follow-up visit. These improvements led to Baby-Friendly designation at our facility. This quality improvement initiative resulted in a higher number of infants exclusively breastfed in our patient population at "high risk not to breastfeed." Other hospitals can use these described methods and techniques to improve their EBF rates. Copyright © 2017 by the American Academy of Pediatrics.

Energy conservation demonstration potential in the food and beverage industry in New Brunswick

Energy Technology Data Exchange (ETDEWEB)

Juchymenko, A

1985-01-01

Concerns expressed by the Food and Beverage industry in the past few years over energy supply and prices have prompted many plant managers to direct their attention to the efficiency with which energy is being used in producing goods and services. Industry is attempting to hold down the total cost of energy by increasing efficiency. This increased efficiency in energy use is accomplished by many methods, some of which are as follows: improved housekeeping and maintenance, use of new materials or improved and more efficient processes and equipment, recycling of materials, modification of existing equipment, use of cogeneration, reduction of energy losses in boilers, ovens, steam pipes, retorts, recovery of waste heat from industrial processes. Cogeneration Associates Limited were engaged to identify two demonstration projects in the Food and Beverage industry which would be suitable for Conservation and Renewable Energy Demonstration Assistance Program (CREDA) financing, and to assist the selected plants in preparing a proposal. A survey of thirty-two establishments was undertaken by means of a mail questionnaire and plant visits. Nineteen projects were identifed which showed suitable pay-back periods. Two projects, Connors Bros. and Carapec Ltd., were selected for further study and detailed proposals were prepared. Connors Bros. submitted a proposal for funding and was successful in obtaining 65% of the total capital cost of $202,000 as a contribution from the CREDA progream. The Connors project demonstrates hot air recovery, hot water recover, and electricity load management. The total energy saving of the project will be $80,000 year, giving a pay-back period of 2.5 years. 6 figs., 1 tab.

Brown Grease to Biodiesel Demonstration Project Report

Energy Technology Data Exchange (ETDEWEB)

San Francisco Public Utilities Commission; URS Corporation; Biofuels, Blackgold; Carollo Engineers

2013-01-30

program by other municipal agencies (as applicable). In order to accomplish the goals of the project, the following steps were performed: 1. Operation of a demonstration facility designed to receive 10,000 to 12,000 gallons of raw Trap Waste each day from private Trap Waste hauling companies. The demonstration facility was designed and built by Pacific Biodiesel Technologies (PBTech). The demonstration facility would also recover 300 gallons of Brown Grease per day from the raw Trap Waste. The recovered Brown Grease was expected to contain no more than 2% Moisture, Insolubles, and Unsaponifiables (MIU) combined. 2. Co-digestion of the side streams (generated during the recovery of 300 gallons of Brown Grease from the raw Trap Waste) with wastewater sludge in the WWTP's anaerobic digesters. The effects of the side streams on anaerobic digestion were quantified by comparison with baseline data. 3. Production of 240 gallons per day of ASTM D6751-S15 grade Biodiesel fuel via a Biodiesel conversion demonstration facility, with the use of recovered Brown Grease as a feedstock. The demonstration facility was designed and built by Blackgold Biofuels (BGB). Side streams from this process were also co-digested with wastewater sludge. Bench-scale anaerobic digestion testing was conducted on side streams from both demonstration facilities to determine potential toxicity and/or changes in biogas production in the WWTP anaerobic digester. While there is a lot of theoretical data available on the lab-scale production of Biodiesel from grease Trap Waste, this full-scale demonstration project was one of the first of its kind in the United States. The project's environmental impacts were expected to include: Reduction of greenhouse gas emissions by prevention of the release of methane at landfills. Although the combustion product of Biodiesel and Methane gas produced in the Anaerobic digester, Carbon Dioxide, is also a greenhouse gas; it is 20 times weaker for the same amount

Photovoltaic demonstration projects 2

Energy Technology Data Exchange (ETDEWEB)

Gillett, W B; Hacker, R J [Halcrow (William) and Partners, Swindon (UK); Kaut, W [eds.

1989-01-01

This book, the proceedings of the third Photovoltaic Contractors' Meeting organised by the Commission of the European Communities, Directorate-General for Energy provides an overview of the photovoltaic demonstration projects which have been supported by the Energy Directorate of the Commission of the European Communities since 1983. It includes reports by each of the contractors who submitted proposals in 1983, 1984 and 1985, describing progress with their projects. The different technologies which are being demonstrated concern the modules, the cabling of the array, structure design, storage strategy and power conditioning. The various applications include powering of houses, villages, recreation centres, water desalination, communications, dairy farms, water pumping and warning systems. (author).

Buried Waste Integrated Demonstration Strategy Plan

International Nuclear Information System (INIS)

Kostelnik, K.M.

1993-02-01

The Buried Waste Integrated Demonstration (BWID) supports the applied research, development, demonstration, and evaluation of a suite of advanced technologies that form a comprehensive remediation system for the effective and efficient remediation of buried waste. These efforts are identified and coordinated in support of the US Department of Energy (DOE), Environmental Restoration and Waste Management (ERWM) needs and objectives. The present focus of BWID is to support retrieval and ex situ treatment configuration options. Future activities will explore and support containment and stabilization efforts in addition to the retrieval/ex situ treatment options. Long and short term strategies of the BWID are provided. Processes for identifying technological needs, screening candidate technologies for BWID applicability, researching technical issues, field demonstrating technologies, evaluating demonstration results to determine each technology's threshold of capability, and commercializing successfully demonstrated technologies for implementation for environmental restoration also are presented in this report

Demonstration of blind quantum computing.

Science.gov (United States)

Barz, Stefanie; Kashefi, Elham; Broadbent, Anne; Fitzsimons, Joseph F; Zeilinger, Anton; Walther, Philip

2012-01-20

Quantum computers, besides offering substantial computational speedups, are also expected to preserve the privacy of a computation. We present an experimental demonstration of blind quantum computing in which the input, computation, and output all remain unknown to the computer. We exploit the conceptual framework of measurement-based quantum computation that enables a client to delegate a computation to a quantum server. Various blind delegated computations, including one- and two-qubit gates and the Deutsch and Grover quantum algorithms, are demonstrated. The client only needs to be able to prepare and transmit individual photonic qubits. Our demonstration is crucial for unconditionally secure quantum cloud computing and might become a key ingredient for real-life applications, especially when considering the challenges of making powerful quantum computers widely available.

Savannah River Plant incinerator demonstration

International Nuclear Information System (INIS)

Lewandowski, K.E.

1983-01-01

A full-scale incineration process was demonstrated at the Savannah River Laboratory (SRL) using nonradioactive waste. From October 1981 through September 1982, 15,700 kilograms of solid waste and 5.7 m 3 of solvent were incinerated. Emissions of off-gas components (NO/sub x/, SO 2 , CO, and particulates) were well below South Carolina state standards. Volume reductions of 20:1 for solid waste and 7:1 for Purex solvent/lime slurry were achieved. The process has been relocated and upgraded by the Savannah River Plant to accept low-level beta-gamma combustibles. During a two-year demonstration, the facility will incinerate slightly radioactive ( 3 ) solvent and suspect level (< 1 mR/h at 0.0254 meter) solid wastes. This demonstration will begin in early 1984

Induced mutations for crop improvement

International Nuclear Information System (INIS)

Micke, A.; Donini, B.; Maluszynski, M.

1990-01-01

Mutation induction has become an established tool in plant breeding to supplement existing germ plasma and to improve cultivars in certain specific traits. Hundreds of improved varieties have been released to farmers for many different crop species, demonstrating the economic value of the technology. Limitations arise mainly from the large mutagenized populations to be screened and from the unsatisfactory selection methods. Both limitations may be eased to some extent by advances in techniques of plant in-vitro culture. (author). Refs, 1 fig., 7 tabs

Get SET: aligning anatomy demonstrator programmes with Surgical Education and Training selection criteria.

Science.gov (United States)

Rhodes, Danielle; Fogg, Quentin A; Lazarus, Michelle D

2018-05-01

Prevocational doctors aspiring to surgical careers are commonly recruited as anatomy demonstrators for undergraduate and graduate medical programmes. Entry into Surgical Education and Training (SET) is highly competitive and a unique opportunity exists to align anatomy demonstrator programmes with the selection criteria and core competencies of SET programmes. This study used a qualitative approach to (i) determine what criteria applicants for SET are assessed on and (ii) identify criteria that could be aligned with and enhanced by an anatomy demonstrator programme. The selection guidelines of all nine surgical specialties for the 2017 intake of SET trainees were analysed using qualitative content analysis methodology. The Royal Australasian College of Surgeons adopted a holistic approach to trainee selection that assessed both discipline-specific and discipline-independent skills. Qualitative content analysis identified eight categories of key selection criteria: medical expertise, scholarly activity, professional identity, interpersonal skills, integrity, self-management, insight and self-awareness and community involvement. The structured curriculum vitae was heavily weighted towards discipline-specific skills, such as medical expertise and scholarly activity. Insufficient information was available to determine the weighting of selection criteria assessed by the structured referee reports or interviews. Anatomy demonstrator programmes provide prevocational doctors with unique opportunities to develop surgical skills and competencies in a non-clinical setting. Constructively aligned anatomy demonstrator programmes may be particularly beneficial for prevocational doctors seeking to improve their anatomical knowledge, teaching skills or scholarly activity. © 2017 Royal Australasian College of Surgeons.

IGCC technology and demonstration

Energy Technology Data Exchange (ETDEWEB)

Palonen, J [A. Ahlstrom Corporation, Karhula (Finland). Hans Ahlstrom Lab.; Lundqvist, R G [A. Ahlstrom Corporation, Helsinki (Finland); Staahl, K [Sydkraft AB, Malmoe (Sweden)

1997-12-31

Future energy production will be performed by advanced technologies that are more efficient, more environmentally friendly and less expensive than current technologies. Integrated gasification combined cycle (IGCC) power plants have been proposed as one of these systems. Utilising biofuels in future energy production will also be emphasised since this lowers substantially carbon dioxide emissions into the atmosphere due to the fact that biomass is a renewable form of energy. Combining advanced technology and biomass utilisation is for this reason something that should and will be encouraged. A. Ahlstrom Corporation of Finland and Sydkraft AB of Sweden have as one part of company strategies adopted this approach for the future. The companies have joined their resources in developing a biomass-based IGCC system with the gasification part based on pressurised circulating fluidized-bed technology. With this kind of technology electrical efficiency can be substantially increased compared to conventional power plants. As a first concrete step, a decision has been made to build a demonstration plant. This plant, located in Vaernamo, Sweden, has already been built and is now in commissioning and demonstration stage. The system comprises a fuel drying plant, a pressurised CFB gasifier with gas cooling and cleaning, a gas turbine, a waste heat recovery unit and a steam turbine. The plant is the first in the world where the integration of a pressurised gasifier with a gas turbine will be realised utilising a low calorific gas produced from biomass. The capacity of the Vaernamo plant is 6 MW of electricity and 9 MW of district heating. Technology development is in progress for design of plants of sizes from 20 to 120 MWe. The paper describes the Bioflow IGCC system, the Vaernamo demonstration plant and experiences from the commissioning and demonstration stages. (orig.)

IGCC technology and demonstration

Energy Technology Data Exchange (ETDEWEB)

Palonen, J. [A. Ahlstrom Corporation, Karhula (Finland). Hans Ahlstrom Lab.; Lundqvist, R.G. [A. Ahlstrom Corporation, Helsinki (Finland); Staahl, K. [Sydkraft AB, Malmoe (Sweden)

1996-12-31

Future energy production will be performed by advanced technologies that are more efficient, more environmentally friendly and less expensive than current technologies. Integrated gasification combined cycle (IGCC) power plants have been proposed as one of these systems. Utilising biofuels in future energy production will also be emphasised since this lowers substantially carbon dioxide emissions into the atmosphere due to the fact that biomass is a renewable form of energy. Combining advanced technology and biomass utilisation is for this reason something that should and will be encouraged. A. Ahlstrom Corporation of Finland and Sydkraft AB of Sweden have as one part of company strategies adopted this approach for the future. The companies have joined their resources in developing a biomass-based IGCC system with the gasification part based on pressurised circulating fluidized-bed technology. With this kind of technology electrical efficiency can be substantially increased compared to conventional power plants. As a first concrete step, a decision has been made to build a demonstration plant. This plant, located in Vaernamo, Sweden, has already been built and is now in commissioning and demonstration stage. The system comprises a fuel drying plant, a pressurised CFB gasifier with gas cooling and cleaning, a gas turbine, a waste heat recovery unit and a steam turbine. The plant is the first in the world where the integration of a pressurised gasifier with a gas turbine will be realised utilising a low calorific gas produced from biomass. The capacity of the Vaernamo plant is 6 MW of electricity and 9 MW of district heating. Technology development is in progress for design of plants of sizes from 20 to 120 MWe. The paper describes the Bioflow IGCC system, the Vaernamo demonstration plant and experiences from the commissioning and demonstration stages. (orig.)

Continued maturing of SOFC cell production technology and development and demonstration of SOFC stacks. Final report

Energy Technology Data Exchange (ETDEWEB)

2008-08-15

The overall objective of the 6385 project was to develop stack materials, components and stack technology including industrial relevant manufacturing methods for cells components and stacks. Furthermore, the project should include testing and demonstration of the stacks under relevant operating conditions. A production of 6.829 cells, twenty 75-cell stacks and a number of small stacks was achieved. Major improvements were also made in the manufacturing methods and in stack design. Two test and demonstration activities were included in the project. The first test unit was established at H.C. OErsted power plant at the Copenhagen waterfront in order to perform test of SOFC stacks. The unit will be used for tests in other projects. The second demonstration unit is the alpha prototype demonstration in a system running on natural gas in Finland. The alpha prototype demonstration system with 24 TOFC (Topsoe Fuel Cell) stacks was established and started running in October 2007 and operational experience was gained in the period from October 2007 to February 2008. (auther)

Manufacturing Demonstration Facility (MDF)

Data.gov (United States)

Federal Laboratory Consortium — The U.S. Department of Energy Manufacturing Demonstration Facility (MDF) at Oak Ridge National Laboratory (ORNL) provides a collaborative, shared infrastructure to...

High-Intensity Interval Training for Improving Postprandial Hyperglycemia

Science.gov (United States)

Little, Jonathan P.; Francois, Monique E.

2014-01-01

High-intensity interval training (HIIT) has garnered attention in recent years as a time-efficient exercise option for improving cardiovascular and metabolic health. New research demonstrates that HIIT may be particularly effective for improving postprandial hyperglycemia in individuals with, or at risk for, type 2 diabetes (T2D). These findings…

Improvement of Wind Farm Performance by Means of Spinner Anemometry

DEFF Research Database (Denmark)

Friis Pedersen, Troels; Demurtas, Giorgio; Gottschall, Julia

This report is a project report on the EUDP research project SpinnerFarm. The objectives of the project were to improve software and hardware on the spinner anemometer concept and to demonstrate improvement of wind farm performance by opitmized yaw control. The hardware was improved by a more...

Effect of science magic applied in interactive lecture demonstrations on conceptual understanding

Science.gov (United States)

Taufiq, Muhammad; Suhandi, Andi; Liliawati, Winny

2017-08-01

Research about the application of science magic-assisting Interactive Lecture Demonstrations (ILD) has been conducted. This research is aimed at providing description about the comparison of the improvement of the conceptual understanding of lesson on pressure between students who receive physics lesson through science magic-assisting ILD and students who receive physics lesson through ILD without science magic. This research used a quasi-experiment methods with Control Group Pretest-Posttest Design. The subject of the research is all students of class VIII in one of MTs (Islamic junior high school) in Pekalongan. Research samples were selected using random sampling technique. Data about students' conceptual understanding was collected using test instrument of conceptual understanding in the form of multiple choices. N-gain average calculation was performed in order to determine the improvement of students' conceptual understanding. The result of the research shows that conceptual understanding of students on lesson about pressure who received lesson with ILD using science magic is higher than students who received lesson with ILD without science magic . Therefore, the conclusion is that the application of science magic ILD is more effective to improve the conceptual understanding of lesson on pressure.

Energy Savings Potential and Research, Development, & Demonstration Opportunities for Commercial Building Appliances

Energy Technology Data Exchange (ETDEWEB)

Zogg, Robert [Navigant Consulting, Inc., Burlington, MA (United States); Goetzler, William [Navigant Consulting, Inc., Burlington, MA (United States); Ahlfeldt, Christopher [Navigant Consulting, Inc., Burlington, MA (United States); Hiraiwa, Hirokazu [Navigant Consulting, Inc., Burlington, MA (United States); Sathe, Amul [Navigant Consulting, Inc., Burlington, MA (United States); Sutherland, Timothy [Navigant Consulting, Inc., Burlington, MA (United States)

2009-12-01

This study characterizes and assesses the appliances used in commercial buildings. The primary objectives of this study were to document the energy consumed by commercial appliances and identify research, development and demonstration (RD&D) opportunities for efficiency improvements, excluding product categories such as HVAC, building lighting, refrigeration equipment, and distributed generation systems. The study included equipment descriptions, characteristics of the equipment’s market, national energy consumption, estimates of technical potential for energy-saving technologies, and recommendations for U.S. Department of Energy programs that can promote energy savings in commercial appliances.

Introduction to Methods Demonstrations for Authentication

International Nuclear Information System (INIS)

Kouzes, Richard T.; Hansen, Randy R.; Pitts, W. K.

2002-01-01

During the Trilateral Initiative Technical Workshop on Authentication and Certification, PNNL will demonstrate some authentication technologies. This paper briefly describes the motivation for these demonstrations and provide background on them

Demonstration of Improved Charge Transfer in Graphene/Au Nanorods Plasmonic Hybrids Stabilized by Benzyl Thiol Linkers

Directory of Open Access Journals (Sweden)

Giuseppe Valerio Bianco

2016-01-01

Full Text Available Hybrids based on graphene decorated with plasmonic gold (Au nanostructures are being investigated as possible materials combination to add to graphene functionalities of tunable plasmon resonance and enhanced absorption at selected wavelength in the visible-near-infrared region of the spectrum. Here, we report a solution drop-casting approach for fabricating stable hybrids based on chemical vapor deposition (CVD graphene and Au nanorods, which are able to activate effective charge transfer from graphene. We demonstrate that CVD graphene functionalization by benzyl thiol (BZT provides the linker to strong anchoring, via S-Au bonds, Au nanorods to graphene. Optical measurements by spectroscopic ellipsometry give evidence of the introduction of plasmon resonances at 1.85 and 2.25 eV in the Au nanorods/BZT/graphene hybrids, which enable surface enhanced Raman scattering (SERS detection. Furthermore, an effective electron transfer from graphene to Au nanorods, resulting in an enhancement of p-type doping of graphene with a consequent decrease of its sheet resistance, is probed by Raman spectroscopy and corroborated by electrical measurements.

Intergovernmental Advanced Stationary PEM Fuel Cell System Demonstration Final Report

Energy Technology Data Exchange (ETDEWEB)

Rich Chartrand

2011-08-31

A program to complete the design, construction and demonstration of a PEMFC system fuelled by Ethanol, LPG or NG for telecom applications was initiated in October 2007. Early in the program the economics for Ethanol were shown to be unfeasible and permission was given by DOE to focus on LPG only. The design and construction of a prototype unit was completed in Jun 2009 using commercially available PEM FC stack from Ballard Power Systems. During the course of testing, the high pressure drop of the stack was shown to be problematic in terms of control and stability of the reformer. Also, due to the power requirements for air compression the overall efficiency of the system was shown to be lower than a similar system using internally developed low pressure drop FC stack. In Q3 2009, the decision was made to change to the Plug power stack and a second prototype was built and tested. Overall net efficiency was shown to be 31.5% at 3 kW output. Total output of the system is 6 kW. Using the new stack hardware, material cost reduction of 63% was achieved over the previous Alpha design. During a November 2009 review meeting Plug Power proposed and was granted permission, to demonstrate the new, commercial version of Plug Power's telecom system at CERL. As this product was also being tested as part of a DOE Topic 7A program, this part of the program was transferred to the Topic 7A program. In Q32008, the scope of work of this program was expanded to include a National Grid demonstration project of a micro-CHP system using hightemperature PEM technology. The Gensys Blue system was cleared for unattended operation, grid connection, and power generation in Aug 2009 at Union College in NY state. The system continues to operate providing power and heat to Beuth House. The system is being continually evaluated and improvements to hardware and controls will be implemented as more is learned about the system's operation. The program is instrumental in improving the

The safety of dipyridamole myocardial perfusion scintigraphy (MPS) in patients with end-stage chronic airways limitations (CAL)

International Nuclear Information System (INIS)

Roman, M.R.; Freeman, A.P.; Angelides, S.

2000-01-01

Full text: Dipyridamole MPS is a well-established investigative technique in the diagnosis and pre-operative risk stratification of patients with possible coronary artery disease. However, there remains a concern of its use in patients with end-stage chronic airways limitations (CAL). Lung volume reduction surgery (LVRS) is a recent therapeutic option for such patients. The options for non-invasive pre-operative cardiac assessment in such patients are limited. This study reviewed the safety of dipyridamole use in such a clinical setting. 20 patients (10M, 10F, mean age 64.8 yrs) were evaluated. None had any history of ischaemic heart disease. Dipyridamole was administered intravenously at a dose of 0.05 mg/kg. Six patients remained asymptomatic throughout the procedure, while none experienced any chest pain. Two patients experienced moderate dyspnoea, which was rapidly relieved with aminophylline (100mg IV) during the recovery phase of the study. Two others developed mild dyspnoea; one settled spontaneously, while the other responded promptly to aminophylline. Aminophylline was administered to nine other patients to reverse minor symptoms (headache, flushing sensation). One other patient developed marked hypotension (SBP fell >20mmHg) and bradycardia, but no ECG changes for myocardial ischaemia. He responded well to aminophylline. His myocardial perfusion scan demonstrated extensive reversible myocardial ischaemia. Although the population size was small, dipyridamole appears safe to use in patients with end-stage CAL. Copyright (2000) The Australian and New Zealand Society of Nuclear Medicine Inc

Laser Communications Relay Demonstration

Data.gov (United States)

National Aeronautics and Space Administration — LCRD is a minimum two year flight demonstration in geosynchronous Earth orbit to advance optical communications technology toward infusion into Deep Space and Near...

Spacecraft Fire Safety Demonstration

Data.gov (United States)

National Aeronautics and Space Administration — The objective of the Spacecraft Fire Safety Demonstration project is to develop and conduct large-scale fire safety experiments on an International Space Station...

Achievement report for fiscal 1998. Energy consumption efficiency improvement model business for developing nations (Demonstration research project on new cooling system in cement clinker production); Hatten tojokoku energy shohi koritsuka model jigyo seika hokokusho. Cement clinker reikyaku sochi ni kakawaru jissho kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The project aims at energy saving and CO2 emission reduction for a clinker cooling system (CCS), and a demonstration test was conducted at a demonstration cement plant in Indonesia. The plant started operation using the new CCS aiming for the enhancement of cooling and heat recovery efficiency. The actually achieved heat recovery efficiency attributable to the adoption of the new CCS was 60.8% against the target of 68%, this meaning an improvement of 8% over the value recorded prior to the new CCS adoption. As for increase in recovered heat due to heat recovery efficiency improvement of the CCS itself, it was 31kcal/kg-clinker. The heat reduction rate throughout the system thanks to the new CCS was 40kcal/kg-clinker. The kiln secondary air temperature increased for improved burner combustion performance for a rise of the clinker burning degree to 12kcal/kg in terms of calorie, and thus a reduction of 52kcal/kg-clinker in total was achieved. No mechanical trouble was reported with the new CCS. Investigations were conducted into cement supply/demand and technological trends in Indonesia, Vietnam, and China. Learnings from the investigation of German cement making technologies were fully utilized in the designing of the new system. (NEDO)

Demonstration of Hadoop-GIS: A Spatial Data Warehousing System Over MapReduce.

Science.gov (United States)

Aji, Ablimit; Sun, Xiling; Vo, Hoang; Liu, Qioaling; Lee, Rubao; Zhang, Xiaodong; Saltz, Joel; Wang, Fusheng

2013-11-01

The proliferation of GPS-enabled devices, and the rapid improvement of scientific instruments have resulted in massive amounts of spatial data in the last decade. Support of high performance spatial queries on large volumes data has become increasingly important in numerous fields, which requires a scalable and efficient spatial data warehousing solution as existing approaches exhibit scalability limitations and efficiency bottlenecks for large scale spatial applications. In this demonstration, we present Hadoop-GIS - a scalable and high performance spatial query system over MapReduce. Hadoop-GIS provides an efficient spatial query engine to process spatial queries, data and space based partitioning, and query pipelines that parallelize queries implicitly on MapReduce. Hadoop-GIS also provides an expressive, SQL-like spatial query language for workload specification. We will demonstrate how spatial queries are expressed in spatially extended SQL queries, and submitted through a command line/web interface for execution. Parallel to our system demonstration, we explain the system architecture and details on how queries are translated to MapReduce operators, optimized, and executed on Hadoop. In addition, we will showcase how the system can be used to support two representative real world use cases: large scale pathology analytical imaging, and geo-spatial data warehousing.

Tidd PFBC Demonstration Project, A DOE Assessment

Energy Technology Data Exchange (ETDEWEB)

National Energy Technology Laboratory

2001-08-31

The Clean Coal Technology (CCT) Demonstration Program is a government and industry co-funded technology development effort to demonstrate a new generation of innovative coal utilization processes. One goal of the program is to furnish the energy marketplace with a variety of energy efficient, environmentally superior coal-based technologies. Demonstration projects seek to establish the commercial feasibility of the most promising coal technologies that have proceeded beyond the proof-of-concept stage. This report is a post-project assessment of the DOE CCT Demonstration Program, the Tidd PFBC Demonstration Project. A major objective of the CCT Program is to provide the technical data necessary for the private sector to proceed confidently with the commercial replication of the demonstrated technologies. An essential element of meeting this goal is the dissemination of results from the demonstration projects. This post-project assessment (PPA) report is an independent DOE appraisal of the successes that the completed project had in achieving its objectives and aiding in the commercialization of the demonstrated technology. The report also provides an assessment of the expected technical, environmental, and economic performance of the commercial version of the technology, as well as an analysis of the commercial market.

Definition and compositions of standard wastestreams for evaluation of Buried Waste Integrated Demonstration treatment technologies

International Nuclear Information System (INIS)

Bates, S.O.

1993-06-01

The Buried Waste Integrated Demonstration (BWID) Project was organized at the Idaho National Engineering Laboratory to support research, development, demonstration, testing, and evaluation of emerging technologies that offer promising solutions to remediation of buried waste. BWID will identify emerging technologies, screen them for applicability to the identified needs, select technologies for demonstration, and then evaluate the technologies based on prescribed performance objectives. The technical objective of the project is to establish solutions to Environmental Restoration and Waste Management's technological deficiencies and improve baseline remediation systems. This report establishes a set of standard wastestream compositions that will be used by BWID to evaluate the emerging technologies. Five wastestreams are proposed that use four types of waste and a nominal case that is a homogenized combination of the four wastes. The five wastestreams will provide data on the compositional extremes and indicate the technologies' effectiveness over the complete range of expected wastestream compositions

A strategy for developing representative germplasm sets for systematic QTL validation, demonstrated for apple, peach, and sweet cherry

NARCIS (Netherlands)

Peace, C.P.; Luby, J.; Weg, van de W.E.; Bink, M.C.A.M.; Iezzoni, A.F.

2014-01-01

Horticultural crop improvement would benefit from a standardized, systematic, and statistically robust procedure for validating quantitative trait loci (QTLs) in germplasm relevant to breeding programs. Here, we describe and demonstrate a strategy for developing reference germplasm sets of

An educational approach to improve outcomes in acute kidney injury (AKI): report of a quality improvement project.

Science.gov (United States)

Xu, Gang; Baines, Richard; Westacott, Rachel; Selby, Nick; Carr, Susan

2014-03-20

To assess the impact of a quality improvement project that used a multifaceted educational intervention on how to improve clinician's knowledge, confidence and awareness of acute kidney injury (AKI). 2 large acute teaching hospitals in England, serving a combined population of over 1.5 million people. All secondary care clinicians working in the clinical areas were targeted, with a specific focus on clinicians working in acute admission areas. A multifaceted educational intervention consisting of traditional didactic lectures, case-based teaching in small groups and an interactive web-based learning resource. We assessed clinicians' knowledge of AKI and their self-reported clinical behaviour using an interactive questionnaire before and after the educational intervention. Secondary outcome measures included clinical audit of patient notes before and after the intervention. 26% of clinicians reported that they were aware of local AKI guidelines in the preintervention questionnaire compared to 64% in the follow-up questionnaire (χ²=60.2, pquality improvement project utilising a multifaceted educational intervention improved awareness of AKI as demonstrated by changes in the clinician's self-reported management of patients with AKI. Elements of the project have been sustained beyond the project period, and demonstrate the power of quality improvement projects to help initiate changes in practice. Our findings are limited by confounding factors and highlight the need to carry out formal randomised studies to determine the impact of educational initiatives in the clinical setting.

Exploration of a Method to Assess Children's Understandings of a Phenomenon after Viewing a Demonstration Show

Science.gov (United States)

DeKorver, Brittland K.; Choi, Mark; Towns, Marcy

2017-01-01

Chemical demonstration shows are a popular form of informal science education (ISE), employed by schools, museums, and other institutions in order to improve the public's understanding of science. Just as teachers employ formative and summative assessments in the science classroom to evaluate the impacts of their efforts, it is important to assess…

Didactic demonstrations of superfluidity and superconductivity phenomena

International Nuclear Information System (INIS)

Aniola-Jedrzejak, L.; Lewicki, A.; Pilipowicz, A.; Tarnawski, Z.; Bialek, H.

1980-01-01

In order to demonstrate to students phenomena of superfluidity and superconductivity a special helium cryostat has been constructed. The demonstrated effects, construction of the cryostat and the method of demonstration are described. (author)

The mixed waste landfill integrated demonstration

International Nuclear Information System (INIS)

Burford, T.D.; Williams, C.V.

1994-01-01

The Mixed Waste Landfill Integrated Demonstration (MWLID) focuses on ''in-situ'' characterization, monitoring, remediation, and containment of landfills in arid environments that contain hazardous and mixed waste. The MWLID mission is to assess, demonstrate, and transfer technologies and systems that lead to faster, better, cheaper, and safer cleanup. Most important, the demonstrated technologies will be evaluated against the baseline of conventional technologies and systems. The comparison will include the cost, efficiency, risk, and feasibility of using these innovative technologies at other sites

Case Report: Improved Homonymous Hemianopia with Hyperbaric Oxygen Therapy

Science.gov (United States)

2017-06-29

in the visual fields was noted at 13 treatments, but approximately 50% improvement was demonstrated in the right eye after 30 treatments with less...significant objective improvement of a fixed neurologic deficit following an ischemic brain injury. Various hypotheses exist regarding the recovery of

Improved exercise myocardial perfusion during lidoflazine therapy

International Nuclear Information System (INIS)

Shapiro, W.; Narahara, K.A.; Park, J.

1983-01-01

Lidoflazine is a synthetic drug with calcium-channel blocking effects. In a study of 6 patients with severe classic angina pectoris, single-blind administration of lidoflazine was associated with improved myocardial perfusion during exercise as determined by thallium-201 stress scintigraphy. These studies demonstrate that lidoflazine therapy is associated with relief of angina, an increased physical work capacity, and improved regional myocardial perfusion during exercise

Generalization of the dispersion relations demonstration; Generalisation de la demonstration des relations de dispersion

Energy Technology Data Exchange (ETDEWEB)

Omnes, Roland [Commissariat a l' energie atomique et aux energies alternatives - CEA (France)

1960-07-01

A modification of the dispersion relations demonstration for two-particle collisions in field theory is indicated. The direct study of the holomorphy domain of the reaction amplitude, without any reference to a particular coordinate system, allows to demonstrate the dispersion relations with fixed pulse transfer for any input and output particle mass. Reprint of a paper published in Comptes rendus des seances de l'Academie des Sciences, t. 250, p. 1203-1205, sitting of 15 February 1960 [French] On indique une modification de la demonstration des relations de dispersion pour les collisions a deux particules en theorie des champs. En etudiant directement le domaine d'holomorphie de l'amplitude de reaction sans se referer a un systeme de coordonnees particulier, on demontre les relations de dispersion a transfert d'impulsion fixe dans le cas ou les masses des particules entrantes et sortantes sont quelconques. Reproduction d'un article publie dans les Comptes rendus des seances de l'Academie des Sciences, t. 250, p. 1203-1205, seance du 15 fevrier 1960.

HTI retrieval demonstration project execution plan

International Nuclear Information System (INIS)

Ellingson, D.R.

1997-01-01

This plan describes the process for demonstrating the retrieval of difficult Hanford tank waste forms utilizing commercial technologies and the private sector to conduct the operations. The demonstration is to be conducted in Tank 241-C-106

DOE's annealing prototype demonstration projects

International Nuclear Information System (INIS)

Warren, J.; Nakos, J.; Rochau, G.

1997-01-01

One of the challenges U.S. utilities face in addressing technical issues associated with the aging of nuclear power plants is the long-term effect of plant operation on reactor pressure vessels (RPVs). As a nuclear plant operates, its RPV is exposed to neutrons. For certain plants, this neutron exposure can cause embrittlement of some of the RPV welds which can shorten the useful life of the RPV. This RPV embrittlement issue has the potential to affect the continued operation of a number of operating U.S. pressurized water reactor (PWR) plants. However, RPV material properties affected by long-term irradiation are recoverable through a thermal annealing treatment of the RPV. Although a dozen Russian-designed RPVs and several U.S. military vessels have been successfully annealed, U.S. utilities have stated that a successful annealing demonstration of a U.S. RPV is a prerequisite for annealing a licensed U.S. nuclear power plant. In May 1995, the Department of Energy's Sandia National Laboratories awarded two cost-shared contracts to evaluate the feasibility of annealing U.S. licensed plants by conducting an anneal of an installed RPV using two different heating technologies. The contracts were awarded to the American Society of Mechanical Engineers (ASME) Center for Research and Technology Development (CRTD) and MPR Associates (MPR). The ASME team completed its annealing prototype demonstration in July 1996, using an indirect gas furnace at the uncompleted Public Service of Indiana's Marble Hill nuclear power plant. The MPR team's annealing prototype demonstration was scheduled to be completed in early 1997, using a direct heat electrical furnace at the uncompleted Consumers Power Company's nuclear power plant at Midland, Michigan. This paper describes the Department's annealing prototype demonstration goals and objectives; the tasks, deliverables, and results to date for each annealing prototype demonstration; and the remaining annealing technology challenges

Halloysite reinforced epoxy composites with improved mechanical properties

Directory of Open Access Journals (Sweden)

Saif Muhammad Jawwad

2016-03-01

Full Text Available Halloysite nanotubes (HNTs reinforced epoxy composites with improved mechanical properties were prepared. The prepared HNTs reinforced epoxy composites demonstrated improved mechanical properties especially the fracture toughness and flexural strength. The flexural modulus of nanocomposite with 6% mHNTs loading was 11.8% higher than that of neat epoxy resin. In addition, the nanocomposites showed improved dimensional stability. The prepared halloysite reinforced epoxy composites were characterized by thermal gravimetric analysis (TGA. The improved properties are attributed to the unique characteristics of HNTs, uniform dispersion of reinforcement and interfacial coupling.

Competence of medical students in communicating drug therapy: Value of role-play demonstrations.

Science.gov (United States)

Tayem, Yasin I; Altabtabaei, Abdulaziz S; Mohamed, Mohamed W; Arrfedi, Mansour M; Aljawder, Hasan S; Aldebous, Fahad A; James, Henry; Al Khaja, Khalid A J; Sequeira, Reginald P

2016-01-01

This study used role-play demonstrations to train medical students to communicate drug therapy and evaluated the perceptions on this instructional approach. The second-year medical students who attended a prescription writing session (n = 133), participated in this study. Prescription communication was introduced by using role-play demonstrations. Participant's perceptions were explored by a self-administered questionnaire and focus group discussion. The academic achievement of attendees and nonattendees was compared with an objective structured performance evaluation (OSPE) station that tested students' competence in this skill. Most attendees responded to the questionnaire (81.2%). Almost all respondents expressed their desire to have similar demonstrations in other units. A large proportion of participants reported that role-play demonstrations helped them develop their communication skills, in general, confidence to communicate drug-related information in a prescription, and the ability to explain the aim of drug therapy to patients. Most trainees thought also that they developed skills to communicate instructions on drug use including drug dose, frequency of administration, duration of therapy, adverse drug reactions, and warnings. During the focus group interviews, students thought that role-play was useful but would be more beneficial if conducted frequently in small group as part of the curriculum implementation. The majority of students also reported improved competence in writing a complete prescription. Analysis of attendees and nonattendees grades in the OSPE showed that the former scored higher than the latter group (P = 0.016). Role-play demonstrations were well accepted by medical students and led to the development of their competence in communicating drug therapy to patients.

Hydrocarbon upgrading demonstration program (HUDP): an investment in the future of the oil sands

Energy Technology Data Exchange (ETDEWEB)

Du Plessis, Duke; Isaacs, Eddy [AI-EES (Canada); Hill, Rich; McPhee, Anne; Keesom, Bill; Arnold, Ed [Jacobs Consultancy (Canada)

2011-07-01

Alberta Innovates Energy and Environment Solutions (AIEES), the technology arm of the Alberta Government in terms of energy and the environment, has initiated the hydrocarbon upgrading demonstration program (HUDP). Since lighter products have a better market value, this program aims to develop technologies for upgrading heavy oil into light, transportable fuel. The program also aims to improve SAGD efficiency while reducing greenhouse gas emissions. To do so, the gaps between typical and ideal operations were identified and quantified, life cycle analyses were performed, current studies were reviewed and future issues and opportunities were assessed. With the HUDP program, AIEES is supporting the industry through investment and technology support to develop innovative technologies which will improve margins and the sustainability of oil sands operations.

The Majorana Demonstrator

Energy Technology Data Exchange (ETDEWEB)

Aguayo, Estanislao; Fast, James E.; Hoppe, Eric W.; Keillor, Martin E.; Kephart, Jeremy D.; Kouzes, Richard T.; LaFerriere, Brian D.; Merriman, Jason H.; Orrell, John L.; Overman, Nicole R.; Avignone, Frank T.; Back, Henning O.; Combs, Dustin C.; Leviner, L.; Young, A.; Barabash, Alexander S.; Konovalov, S.; Vanyushin, I.; Yumatov, Vladimir; Bergevin, M.; Chan, Yuen-Dat; Detwiler, Jason A.; Loach, J. C.; Martin, R. D.; Poon, Alan; Prior, Gersende; Vetter, Kai; Bertrand, F.; Cooper, R. J.; Radford, D. C.; Varner, R. L.; Yu, Chang-Hong; Boswell, M.; Elliott, S.; Gehman, Victor M.; Hime, Andrew; Kidd, M. F.; LaRoque, B. H.; Rielage, Keith; Ronquest, M. C.; Steele, David; Brudanin, V.; Egorov, Viatcheslav; Gusey, K.; Kochetov, Oleg; Shirchenko, M.; Timkin, V.; Yakushev, E.; Busch, Matthew; Esterline, James H.; Tornow, Werner; Christofferson, Cabot-Ann; Horton, Mark; Howard, S.; Sobolev, V.; Collar, J. I.; Fields, N.; Creswick, R.; Doe, Peter J.; Johnson, R. A.; Knecht, A.; Leon, Jonathan D.; Marino, Michael G.; Miller, M. L.; Robertson, R. G. H.; Schubert, Alexis G.; Wolfe, B. A.; Efremenko, Yuri; Ejiri, H.; Hazama, R.; Nomachi, Masaharu; Shima, T.; Finnerty, P.; Fraenkle, Florian; Giovanetti, G. K.; Green, M.; Henning, Reyco; Howe, M. A.; MacMullin, S.; Phillips, D.; Snavely, Kyle J.; Strain, J.; Vorren, Kris R.; Guiseppe, Vincente; Keller, C.; Mei, Dong-Ming; Perumpilly, Gopakumar; Thomas, K.; Zhang, C.; Hallin, A. L.; Keeter, K.; Mizouni, Leila; Wilkerson, J. F.

2011-09-03

A brief review of the history and neutrino physics of double beta decay is given. A description of the MAJORANA DEMONSTRATOR research and development program, including background reduction techniques, is presented in some detail. The application of point contact (PC) detectors to the experiment is discussed, including the effectiveness of pulse shape analysis. The predicted sensitivity of a PC detector array enriched to 86% to 76Ge is given.

The buried waste integrated demonstration

International Nuclear Information System (INIS)

Kostelnik, K.M.

1991-01-01

There are numerous locations throughout the Department of Energy (DOE) Complex where wastes have been buried in the ground or stored for future disposal. Much of this buried waste is contaminated with hazardous and radioactive materials. An extensive research program has been initiated at the Idaho National Engineering Laboratory (INEL) to develop and demonstrate advanced remediation techniques for DOE Complex buried waste. The purpose of the Buried Waste Integrated Demonstration (BWID), is to develop a scientifically sound and deployable remediation system consisting of advanced technologies which address the buried waste characteristics of the DOE Complex. This comprehensive remediation system win include technologies for the entire remediation cycle (cradle-to-grave). Technologies developed and demonstrated within the BWID will be transferred to the DOE Complex sites with buried waste, to private industry, and to universities. Multidirectional technology transfer is encouraged by the BWID. Identification and evaluation of plausible technological solutions are an ongoing activity of the BWID. A number of technologies are currently under development throughout the DOE Complex, private industry, and universities. Technology integration mechanisms have been established by BWID to facilitate collaborative research and demonstration of applicable remedial technologies for buried waste. Successful completion of the BWID will result in the development of a proven and deployable system at the INEL and other DOE Complex buried waste sites, thereby supporting the DOE Complex's environmental restoration objectives

Kaolinitic clay-based grouting demonstration

International Nuclear Information System (INIS)

McCloskey, A.L.; Barry, C.J.; Wilmoth, R.

1997-01-01

An innovative Kaolinitic Clay-Based Grouting Demonstration was performed under the Mine Waste Technology Program (MWTP), funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by the EPA and the U.S. Department of Energy (DOE). The objective of the technology was to demonstrate the effectiveness of kaolinitic clay-based grouting in reducing/eliminating infiltration of surface and shallow groundwater through fractured bedrock into underground mine workings. In 1993, the Mike Horse Mine was selected as a demonstration site for the field implementation and evaluation of the grouting technology. The mine portal discharge ranged between 114 to 454 liters per minute (30 to 120 gpm) of water containing iron, zinc, manganese, and cadmium at levels exceeding the National Drinking Water Maximum Contaminant Levels. The grout formulation was designed by the developer Morrison Knudsen Corporation/Spetstamponazhgeologia (MK/STG), in May 1994. Grout injection was performed by Hayward Baker, Inc. under the directive of MSE Technology Applications, Inc. (MSE-TA) during fall of 1994. The grout was injected into directionally-drilled grout holes to form a grout curtain at the project site. Post grout observations suggest the grout was successful in reducing the infiltration of the surface and shallow groundwater from entering the underground mine workings. The proceeding paper describes the demonstration and technology used to form the subsurface barrier in the fracture system

SOx-NOx-Rox Box{trademark} flue gas clean-up demonstration. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

The SNRB{trademark} Flue Gas Cleanup Demonstration Project was cooperatively funded by the U.S. Department of Energy (DOE), the Ohio Coal Development Office (OCDO), B&W, the Electric Power Research Institute (EPRI), Ohio Edison, Norton Chemical Process Products Company and the 3M Company. The SNRB{trademark} technology evolved from the bench and laboratory pilot scale to be successfully demonstrated at the 5-MWe field scale. Development of the SNRB{trademark} process at B&W began with pilot testing of high-temperature dry sorbent injection for SO{sub 2} removal in the 1960`s. Integration of NO{sub x} reduction was evaluated in the 1970`s. Pilot work in the 1980`s focused on evaluation of various NO{sub x} reduction catalysts, SO{sub 2} sorbents and integration of the catalyst with the baghouse. This early development work led to the issuance of two US process patents to B&W - No. 4,309,386 and No. 4,793,981. An additional patent application for improvements to the process is pending. The OCDO was instrumental in working with B&W to develop the process to the point where a larger scale demonstration of the technology was feasible. This report represents the completion of Milestone M14 as specified in the Work Plan. B&W tested the SNRB{trademark} pollution control system at a 5-MWe demonstration facility at Ohio Edison`s R. E. Burger Plant located near Shadyside, Ohio. The design and operation were influenced by the results from laboratory pilot testing at B&W`s Alliance Research Center. The intent was to demonstrate the commercial feasibility of the SNRB{trademark} process. The SNRB{trademark} facility treated a 30,000 ACFM flue gas slipstream from Boiler No. 8. Operation of the facility began in May 1992 and was completed in May 1993.

Improved TOPSIS decision model for NPP emergencies

International Nuclear Information System (INIS)

Zhang Jin; Liu Feng; Huang Lian

2011-01-01

In this paper,an improved decision model is developed for its use as a tool to respond to emergencies at nuclear power plants. Given the complexity of multi-attribute emergency decision-making on nuclear accident, the improved TOPSIS method is used to build a decision-making model that integrates subjective weight and objective weight of each evaluation index. A comparison between the results of this new model and two traditional methods of fuzzy hierarchy analysis method and weighted analysis method demonstrates that the improved TOPSIS model has a better evaluation effect. (authors)

The Optimizing Patient Transfers, Impacting Medical Quality, andImproving Symptoms:Transforming Institutional Care approach: preliminary data from the implementation of a Centers for Medicare and Medicaid Services nursing facility demonstration project.

Science.gov (United States)

Unroe, Kathleen T; Nazir, Arif; Holtz, Laura R; Maurer, Helen; Miller, Ellen; Hickman, Susan E; La Mantia, Michael A; Bennett, Merih; Arling, Greg; Sachs, Greg A

2015-01-01

The Optimizing Patient Transfers, Impacting Medical Quality, and Improving Symptoms: Transforming Institutional Care (OPTIMISTIC) project aims to reduce avoidable hospitalizations of long-stay residents enrolled in 19 central Indiana nursing facilities. This clinical demonstration project, funded by the Centers for Medicare and Medicaid Services Innovations Center, places a registered nurse in each nursing facility to implement an evidence-based quality improvement program with clinical support from nurse practitioners. A description of the model is presented, and early implementation experiences during the first year of the project are reported. Important elements include better medical care through implementation of Interventions to Reduce Acute Care Transfers tools and chronic care management, enhanced transitional care, and better palliative care with a focus on systematic advance care planning. There were 4,035 long-stay residents in 19 facilities enrolled in OPTIMISTIC between February 2013 and January 2014. Root-cause analyses were performed for all 910 acute transfers of these long stay residents. Of these transfers, the project RN evaluated 29% as avoidable (57% were not avoidable and 15% were missing), and opportunities for quality improvement were identified in 54% of transfers. Lessons learned in early implementation included defining new clinical roles, integrating into nursing facility culture, managing competing facility priorities, communicating with multiple stakeholders, and developing a system for collecting and managing data. The success of the overall initiative will be measured primarily according to reduction in avoidable hospitalizations of long-stay nursing facility residents. © 2014, Copyright the Authors Journal compilation © 2014, The American Geriatrics Society.

A Demonstration of Evidence-Based Action Research Using Information Dashboard in Introductory Programming Education

OpenAIRE

Matsuzawa , Yoshiaki; Tanaka , Yoshiki; Kitani , Tomoya; Sakai , Sanshiro

2017-01-01

Part 3: Computer Science Education and Its Future Focus and Development; International audience; In this paper, we demonstrated an evidence-based action research in an introductory programming class with the use of an information dashboard which provides coding metrics to visualize students’ engagement of their assignments. The information dashboard was designed for teachers to improve their classroom teaching using the same coding metrics which was verified in our previous research [9]. The ...

Improved reconstruction for IDEAL spiral CSI

DEFF Research Database (Denmark)

Hansen, Rie Beck; Mariager, Christian; Laustsen, Christoffer

2017-01-01

In this study we demonstrate how reconstruction for IDEAL spiral CSI (spectroscopic imaging scheme developed for hyperpolarized dynamic metabolic MR imaging) can be improved by using regularization with a sparsity constraint. By exploiting sparsity of the spectral domain, IDEAL spiral CSI can...

How to Demonstrate Microgravity in your Classroom

Science.gov (United States)

DeLombard, Richard; Hall, Nancy Rabel

2013-01-01

Learn why zero gravity is a misnomer and learn how to demonstrate microgravity to students and the general public. In this session, a short theory segment will explain and reinforce these concepts so that you may explain to others. Session participants will also see simple equipment that demonstrates microgravity during the session and can just as well be done in the classroom or museum exhibit hall. The hands-on demonstration devices range from a leaky water bottle to an electronic drop tower with an on-board camera. The session will also include demonstration techniques for Physics, Forces & Motion, and orbits. This material is useful for middle school forces and motions instruction, high school physics instruction, public demonstrations at conferences & school open houses, travelling museum exhibits, fixed museum exhibits, and independent student projects or experiments. These activities also connect the terrestrial demonstration with planetary & moon motion, comet trajectory, and more.

Overview about the fuel cell bus demonstration programs CUTE, ECTOS and STEP

International Nuclear Information System (INIS)

Faltenbacher, M.; Fischer, M.; Eyerer, P.; Binder, M.; Schuckert, M.

2004-01-01

'Full text:' The paper will give an overview about the CUTE, ECTOS and STEP projects. The aim of the projects is to develop and demonstrate a emission-free and low-noise transport system, including the accompanying energy infrastructure, which has great potential for reducing the global greenhouse effect according to the Kyoto protocol, improving the quality of the atmosphere and life in densely populated areas and conserving fossil resources. For this purpose the application of the innovative hydrogen-based fuel cell technology is established by using fuel cell powered buses in an urban environment together with novel hydrogen production and support systems as part of a European Union wide demonstration scheme. The project demonstrates also to European Society the availability of the FC technology as a safe and reliable transportation technology. The major objectives are as follows: Demonstration of more than 20 fuel cell powered regular service buses over a period of two years in several European inner city areas to illustrate the different operating conditions to be found in Europe; Design, construction and operation of the necessary infrastructure for hydrogen production, including the required refuelling stations; Collection of findings concerning the construction and operating behaviour of hydrogen production for mobile use, and exchange of experiences including bus operation under differing conditions among the numerous participating companies; and, the research work of IKP and PE comprises the ecological analysis of the entire life cycle and comparison with conventional alternatives (diesel driven buses, CNG-buses). It also includes the economical analysis of the hydrogen infrastructure. First experiences from CUTE and ECTOS were presented. (author)

The ecological impacts of marine debris: unraveling the demonstrated evidence from what is perceived.

Science.gov (United States)

Rochman, Chelsea M; Browne, Mark Anthony; Underwood, A J; van Franeker, Jan A; Thompson, Richard C; Amaral-Zettler, Linda A

2016-02-01

Anthropogenic debris contaminates marine habitats globally, leading to several perceived ecological impacts. Here, we critically and systematically review the literature regarding impacts of debris from several scientific fields to understand the weight of evidence regarding the ecological impacts of marine debris. We quantified perceived and demonstrated impacts across several levels of biological organization that make up the ecosystem and found 366 perceived threats of debris across all levels. Two hundred and ninety-six of these perceived threats were tested, 83% of which were demonstrated. The majority (82%) of demonstrated impacts were due to plastic, relative to other materials (e.g., metals, glass) and largely (89%) at suborganismal levels (e.g., molecular, cellular, tissue). The remaining impacts, demonstrated at higher levels of organization (i.e., death to individual organisms, changes in assemblages), were largely due to plastic marine debris (> 1 mm; e.g., rope, straws, and fragments). Thus, we show evidence of ecological impacts from marine debris, but conclude that the quantity and quality of research requires improvement to allow the risk of ecological impacts of marine debris to be determined with precision. Still, our systematic review suggests that sufficient evidence exists for decision makers to begin to mitigate problematic plastic debris now, to avoid risk of irreversible harm.

Using Daily Horoscopes To Demonstrate Expectancy Confirmation.

Science.gov (United States)

Munro, Geoffrey D.; Munro, James E.

2000-01-01

Describes a classroom demonstration that uses daily horoscopes to show the effect that expectation can have on judgment. Addresses the preparation, procedure, and results of the demonstration, and student evaluations. States that the demonstration appears to be effective for teaching students about expectancy confirmation. (CMK)

Cone penetrometer demonstration standard startup review checklist

International Nuclear Information System (INIS)

KRIEG, S.A.

1998-01-01

Startup readiness for the Cone Penetrometer Demonstration in AX Tank Farm will be verified through the application of a Standard Startup Review Checklist. This is a listing of those items essential to demonstrating readiness to start the Cone Penetrometer Demonstration in AX Tank Farm

Sevoflurane improves gaseous exchange and exerts protective ...

African Journals Online (AJOL)

Sevoflurane improves gaseous exchange and exerts protective effects in ... Lung water content and cell count were estimated by standard protocols. ... It reversed LPS-induced oxidative stress, as demonstrated by increase in total antioxidant ...

Reliability demonstration of imaging surveillance systems

International Nuclear Information System (INIS)

Sheridan, T.F.; Henderson, J.T.; MacDiarmid, P.R.

1979-01-01

Security surveillance systems which employ closed circuit television are being deployed with increasing frequency for the protection of property and other valuable assets. A need exists to demonstrate the reliability of such systems before their installation to assure that the deployed systems will operate when needed with only the scheduled amount of maintenance and support costs. An approach to the reliability demonstration of imaging surveillance systems which employ closed circuit television is described. Failure definitions based on industry television standards and imaging alarm assessment criteria for surveillance systems are discussed. Test methods which allow 24 hour a day operation without the need for numerous test scenarios, test personnel and elaborate test facilities are presented. Existing reliability demonstration standards are shown to apply which obviate the need for elaborate statistical tests. The demonstration methods employed are shown to have applications in other types of imaging surveillance systems besides closed circuit television

Design of helium-gas supplying facility of out-of-pile demonstration test for HTTR heat utilization system

Energy Technology Data Exchange (ETDEWEB)

Hino, Ryutaro; Fujisaki, Katsuo; Kobayashi, Toshiaki [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment] [and others

1996-09-01

One of the objectives of the High-Temperature Engineering Test Reactor (HTTR) is to demonstrate effectiveness of high-temperature heat utilization. Prior to connect a heat utilization system to the HTTR, a series of out-of-pile demonstration test is indispensable to improve components` performance, to demonstrate operation, control and safety technologies and to verify analysis codes for design and safety evaluation. After critical review and discussion on the out-of-pile demonstration test, a test facility have been designed. In this report, a helium-gas supplying facility simulated the HTTR system was described in detail, which supplies High-temperature helium-gas of 900degC to a steam reforming facility mocking-up the HTTR heat utilization system. Components of the Helium Engineering Demonstration Loop (HENDEL) were selected to reuse in the helium-gas supplying facility in order to decrease construction cost. Structures and specifications of new components such as a high-temperature heater and a preheater were decided after evaluation of thermal and hydraulic performance and strength. (author)

Real-time new satellite product demonstration from microwave sensors and GOES-16 at NRL TC web

Science.gov (United States)

Cossuth, J.; Richardson, K.; Surratt, M. L.; Bankert, R.

2017-12-01

The Naval Research Laboratory (NRL) Tropical Cyclone (TC) satellite webpage (https://www.nrlmry.navy.mil/TC.html) provides demonstration analyses of storm imagery to benefit operational TC forecast centers around the world. With the availability of new spectral information provided by GOES-16 satellite data and recent research into improved visualization methods of microwave data, experimental imagery was operationally tested to visualize the structural changes of TCs during the 2017 hurricane season. This presentation provides an introduction into these innovative satellite analysis methods, NRL's next generation satellite analysis system (the Geolocated Information Processing System, GeoIPSTM), and demonstration the added value of additional spectral frequencies when monitoring storms in near-realtime.

Design of an advanced bundle divertor for the Demonstration Tokamak Hybrid Reactor

International Nuclear Information System (INIS)

Yang, T.F.; Lee, A.Y.; Ruck, G.W.; Prevenslik, T.V.; Smeltzer, G.

1979-01-01

The conclusion of this work is that a bundle divertor, using an improved method of designing the magnetic field configuration, is feasible for the Demonstration Tokamak Hybrid Reactor (DTHR) investigated by Westinghouse. The most significant achievement of this design is the reduction in current density (1 kA/cm 2 ) in the divertor coils in comparison to the overall averaged current densities per tesla of field to be nulled for DITE (25 kA/cm 2 ) and for ISX-B 2 (11 kA/cm 2 ). Therefore, superconducting magnets can be built into the tight space available with a sound mechanical structure

Experimental demonstration of multiple-inputs multiple-outputs OFDM/OQAM visible light communications

Science.gov (United States)

Lin, Bangjiang; Tang, Xuan; Ghassemlooy, Zabih; Lin, Chun; Zhang, Min

2017-10-01

We experimentally demonstrate a 2×2 optical multiple-inputs multiple-outputs (MIMO) visible light communications system based on the modified orthogonal frequency-division multiplexing/offset quadrature amplitude modulation scheme. The adjacent subcarrier frequency-domain averaging (ASFA) with the full-loaded (FL) and half-loaded (HL) preamble structures is proposed for demultiplexing and mitigating the intrinsic imaginary interference (IMI) effect. Compared with the conventional channel estimation (CE) method, ASFA offers improved transmission performance. With the FL method, we obtain more accurate MIMO CE to mitigate the IMI effect and the optical noise compared to the HL method.

REFLEX : A metacognitive group treatment to improve insight in psychosis

NARCIS (Netherlands)

Pijnenborg, M.; Van der Meer, L.; De Vos, A.; Bockting, C. L. H.; Van der Gaag, M.; Aleman, A.

2013-01-01

Background: Many people with schizophrenia (50-80%) demonstrate impaired insight. A number of interventions aiming to improve insight have been proposed and evaluated, for example cognitive behavioral therapy and psycho-education. Results of these interventions leave room for improvement. Therefore,

Recovery Act--Class 8 Truck Freight Efficiency Improvement Project

Energy Technology Data Exchange (ETDEWEB)

Trucks, Daimler [Daimler Trucks North America Llc, Portland, OR (United States)

2015-07-26

Daimler Trucks North America completed a five year, $79.6M project to develop and demonstrate a concept vehicle with at least 50% freight efficiency improvement over a weighted average of several drive cycles relative to a 2009 best-in-class baseline vehicle. DTNA chose a very fuel efficient baseline vehicle, the 2009 Freightliner Cascadia with a DD15 engine, yet successfully demonstrated a 115% freight efficiency improvement. DTNA learned a great deal about the various technologies that were incorporated into Super Truck and those that, through down-selection, were discarded. Some of the technologies competed with each other for efficiency, and notably some of the technologies complemented each other. For example, we found that Super Truck’s improved aerodynamic drag resulted in improved fuel savings from eCoast, relative to a similar vehicle with worse aerodynamic drag. However, some technologies were in direct competition with each other, namely the predictive technologies which use GPS and 3D digital maps to efficiently manage the vehicles kinetic energy through controls and software, versus hybrid which is a much costlier technology that essentially targets the same inefficiency. Furthermore, the benefits of a comprehensive, integrated powertrain/vehicle approach was proven, in which vast improvements in vehicle efficiency (e.g. lower aero drag and driveline losses) enabled engine strategies such as downrating and downspeeding. The joint engine and vehicle developments proved to be a multiplier-effect which resulted in large freight efficiency improvements. Although a large number of technologies made the selection process and were used on the Super Truck demonstrator vehicle, some of the technologies proved not feasible for series production.

SunJammer Technology Demonstration

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Sunjammer Project is a NASA funded contract to L?Garde Inc. to fly a solar sail demonstration for a period of approximately one year. L?Garde is also partnered...

Demonstration of SiC Pressure Sensors at 750 C

Science.gov (United States)

Okojie, Robert S.; Lukco, Dorothy; Nguyen, Vu; Savrun, Ender

2014-01-01

We report the first demonstration of MEMS-based 4H-SiC piezoresistive pressure sensors tested at 750 C and in the process confirmed the existence of strain sensitivity recovery with increasing temperature above 400 C, eventually achieving near or up to 100% of the room temperature values at 750 C. This strain sensitivity recovery phenomenon in 4H-SiC is uncharacteristic of the well-known monotonic decrease in strain sensitivity with increasing temperature in silicon piezoresistors. For the three sensors tested, the room temperature full-scale output (FSO) at 200 psig ranged between 29 and 36 mV. Although the FSO at 400 C dropped by about 60%, full recovery was achieved at 750 C. This result will allow the operation of SiC pressure sensors at higher temperatures, thereby permitting deeper insertion into the engine combustion chamber to improve the accurate quantification of combustor dynamics.

Demonstration of a utility industry horizontal drilling system: Horizontal well AMH-5 installation report

International Nuclear Information System (INIS)

1992-01-01

The Department of Energy's Office of Technology Development initiated an integrated demonstration of innovative technologies and systems for cleanup of VOCs in soils and groundwater at the Savannah River Site (SRS) in 1989. The overall goal of the program is demonstration of multiple technologies and systems in the fields of drilling, characterization, monitoring, and remediation at a single test bed. Innovative technologies are compared to one another and to baseline technologies in terms of technical performance and cost effectiveness. Transfer of successfully demonstrated technologies and systems to DOE environmental restoration organizations, to other government agencies, and to industry is a critical part of the program. Directional drilling has been shown to be a successful technique for enhancing access to the subsurface, thus improving remediation systems, especially remediation systems which perform in situ. Demonstration of an innovative directional drilling system at the Integrated Demonstration Site at the SRS, was initiated in June of 1992. The directional drilling system was designed to install an in situ remediation system. The drilling system is an experimental compaction/dry drilling technique developed by Charles Machine Works (Ditch Witch reg-sign) of Perry, Oklahoma. A horizontal well was installed in the M Area of the SRS below and parallel to an abandoned tile process sewer line. The installation of the horizontal well was a two-part process. Part one consisted of drilling the borehole, and part two was the horizontal well completion

Orbital Express fluid transfer demonstration system

Science.gov (United States)

Rotenberger, Scott; SooHoo, David; Abraham, Gabriel

2008-04-01

Propellant resupply of orbiting spacecraft is no longer in the realm of high risk development. The recently concluded Orbital Express (OE) mission included a fluid transfer demonstration that operated the hardware and control logic in space, bringing the Technology Readiness Level to a solid TRL 7 (demonstration of a system prototype in an operational environment). Orbital Express (funded by the Defense Advanced Research Projects Agency, DARPA) was launched aboard an Atlas-V rocket on March 9th, 2007. The mission had the objective of demonstrating technologies needed for routine servicing of spacecraft, namely autonomous rendezvous and docking, propellant resupply, and orbital replacement unit transfer. The demonstration system used two spacecraft. A servicing vehicle (ASTRO) performed multiple dockings with the client (NextSat) spacecraft, and performed a variety of propellant transfers in addition to exchanges of a battery and computer. The fluid transfer and propulsion system onboard ASTRO, in addition to providing the six degree-of-freedom (6 DOF) thruster system for rendezvous and docking, demonstrated autonomous transfer of monopropellant hydrazine to or from the NextSat spacecraft 15 times while on orbit. The fluid transfer system aboard the NextSat vehicle was designed to simulate a variety of client systems, including both blowdown pressurization and pressure regulated propulsion systems. The fluid transfer demonstrations started with a low level of autonomy, where ground controllers were allowed to review the status of the demonstration at numerous points before authorizing the next steps to be performed. The final transfers were performed at a full autonomy level where the ground authorized the start of a transfer sequence and then monitored data as the transfer proceeded. The major steps of a fluid transfer included the following: mate of the coupling, leak check of the coupling, venting of the coupling, priming of the coupling, fluid transfer, gauging

Affordable Development and Demonstration of a Small NTR engine and Stage: A Preliminary NASA, DOE, and Industry Assessment

Science.gov (United States)

Borowski, S. K.; Sefcik, R. J.; Fittje, J. E.; McCurdy, D. R.; Qualls, A. L.; Schnitzler, B. G; Werner, J.; Weitzberg, A.; Joyner, C. R.

2015-01-01

In FY'11, Nuclear Thermal Propulsion (NTP) was identified as a key propulsion option under the Advanced In-Space Propulsion (AISP) component of NASA's Exploration Technology Development and Demonstration (ETDD) program A strategy was outlined by GRC and NASA HQ that included 2 key elements -"Foundational Technology Development" followed by specific "Technology Demonstration" projects. The "Technology Demonstration "element proposed ground technology demonstration (GTD) testing in the early 2020's, followed by a flight technology demonstration (FTD) mission by approx. 2025. In order to reduce development costs, the demonstration projects would focus on developing a small, low thrust (approx. 7.5 -16.5 klb(f)) engine that utilizes a "common" fuel element design scalable to the higher thrust (approx. 25 klb(f)) engines used in NASA's Mars DRA 5.0 study(NASA-SP-2009-566). Besides reducing development costs and allowing utilization of existing, flight proven engine hard-ware (e.g., hydrogen pumps and nozzles), small, lower thrust ground and flight demonstration engines can validate the technology and offer improved capability -increased payloads and decreased transit times -valued for robotic science missions identified in NASA's Decadal Study.

Improved analysis of long-term monitoring data demonstrates marked regional declines of bat populations in the eastern United States

Science.gov (United States)

Thomas E. Ingersoll; Brent J. Sewall; Sybill K. Amelon

2013-01-01

Bats are diverse and ecologically important, but are also subject to a suite of severe threats. Evidence for localized bat mortality from these threats is well-documented in some cases, but long-term changes in regional populations of bats remain poorly understood. Bat hibernation surveys provide an opportunity to improve understanding, but analysis is complicated by...

Improving ED specimen TAT using Lean Six Sigma.

Science.gov (United States)

Sanders, Janet H; Karr, Tedd

2015-01-01

Lean and Six Sigma are continuous improvement methodologies that have garnered international fame for improving manufacturing and service processes. Increasingly these methodologies are demonstrating their power to also improve healthcare processes. The purpose of this paper is to discuss a case study for the application of Lean and Six Sigma tools in the reduction of turnaround time (TAT) for Emergency Department (ED) specimens. This application of the scientific methodologies uncovered opportunities to improve the entire ED to lab system for the specimens. This case study provides details on the completion of a Lean Six Sigma project in a 1,000 bed tertiary care teaching hospital. Six Sigma's Define, Measure, Analyze, Improve, and Control methodology is very similar to good medical practice: first, relevant information is obtained and assembled; second, a careful and thorough diagnosis is completed; third, a treatment is proposed and implemented; and fourth, checks are made to determine if the treatment was effective. Lean's primary goal is to do more with less work and waste. The Lean methodology was used to identify and eliminate waste through rapid implementation of change. The initial focus of this project was the reduction of turn-around-times for ED specimens. However, the results led to better processes for both the internal and external customers of this and other processes. The project results included: a 50 percent decrease in vials used for testing, a 50 percent decrease in unused or extra specimens, a 90 percent decrease in ED specimens without orders, a 30 percent decrease in complete blood count analysis (CBCA) Median TAT, a 50 percent decrease in CBCA TAT Variation, a 10 percent decrease in Troponin TAT Variation, a 18.2 percent decrease in URPN TAT Variation, and a 2-5 minute decrease in ED registered nurses rainbow draw time. This case study demonstrated how the quantitative power of Six Sigma and the speed of Lean worked in harmony to improve

Professor's Page: Do Demonstration Lessons Work?

Science.gov (United States)

Clarke, Doug

2011-01-01

As part of a large research and professional development project funded by the Catholic Education Office Melbourne (CEOM), called "Contemporary Teaching and Learning of Mathematics," the ACU team has been leading demonstration lessons. There is certainly not universal agreement on the worth of demonstration lessons in the mathematics…

Aerospace Communications Security Technologies Demonstrated

Science.gov (United States)

Griner, James H.; Martzaklis, Konstantinos S.

2003-01-01

In light of the events of September 11, 2001, NASA senior management requested an investigation of technologies and concepts to enhance aviation security. The investigation was to focus on near-term technologies that could be demonstrated within 90 days and implemented in less than 2 years. In response to this request, an internal NASA Glenn Research Center Communications, Navigation, and Surveillance Aviation Security Tiger Team was assembled. The 2-year plan developed by the team included an investigation of multiple aviation security concepts, multiple aircraft platforms, and extensively leveraged datalink communications technologies. It incorporated industry partners from NASA's Graphical Weather-in-the-Cockpit research, which is within NASA's Aviation Safety Program. Two concepts from the plan were selected for demonstration: remote "black box," and cockpit/cabin surveillance. The remote "black box" concept involves real-time downlinking of aircraft parameters for remote monitoring and archiving of aircraft data, which would assure access to the data following the loss or inaccessibility of an aircraft. The cockpit/cabin surveillance concept involves remote audio and/or visual surveillance of cockpit and cabin activity, which would allow immediate response to any security breach and would serve as a possible deterrent to such breaches. The datalink selected for the demonstrations was VDL Mode 2 (VHF digital link), the first digital datalink for air-ground communications designed for aircraft use. VDL Mode 2 is beginning to be implemented through the deployment of ground stations and aircraft avionics installations, with the goal of being operational in 2 years. The first demonstration was performed December 3, 2001, onboard the LearJet 25 at Glenn. NASA worked with Honeywell, Inc., for the broadcast VDL Mode 2 datalink capability and with actual Boeing 757 aircraft data. This demonstration used a cockpitmounted camera for video surveillance and a coupling to

Exploration Medical System Demonstration

Science.gov (United States)

Rubin, D. A.; Watkins, S. D.

2014-01-01

BACKGROUND: Exploration class missions will present significant new challenges and hazards to the health of the astronauts. Regardless of the intended destination, beyond low Earth orbit a greater degree of crew autonomy will be required to diagnose medical conditions, develop treatment plans, and implement procedures due to limited communications with ground-based personnel. SCOPE: The Exploration Medical System Demonstration (EMSD) project will act as a test bed on the International Space Station (ISS) to demonstrate to crew and ground personnel that an end-to-end medical system can assist clinician and non-clinician crew members in optimizing medical care delivery and data management during an exploration mission. Challenges facing exploration mission medical care include limited resources, inability to evacuate to Earth during many mission phases, and potential rendering of medical care by non-clinicians. This system demonstrates the integration of medical devices and informatics tools for managing evidence and decision making and can be designed to assist crewmembers in nominal, non-emergent situations and in emergent situations when they may be suffering from performance decrements due to environmental, physiological or other factors. PROJECT OBJECTIVES: The objectives of the EMSD project are to: a. Reduce or eliminate the time required of an on-orbit crew and ground personnel to access, transfer, and manipulate medical data. b. Demonstrate that the on-orbit crew has the ability to access medical data/information via an intuitive and crew-friendly solution to aid in the treatment of a medical condition. c. Develop a common data management framework that can be ubiquitously used to automate repetitive data collection, management, and communications tasks for all activities pertaining to crew health and life sciences. d. Ensure crew access to medical data during periods of restricted ground communication. e. Develop a common data management framework that

A description of the demonstration Integral Fast Reactor fuel cycle facility

International Nuclear Information System (INIS)

Courtney, J.C.; Carnes, M.D.; Dwight, C.C.; Forrester, R.J.

1991-01-01

A fuel examination facility at the Idaho National Engineering Laboratory is being converted into a facility that will electrochemically process spent fuel. This is an important step in the demonstration of the Integral Fast Reactor concept being developed by Argonne National Laboratory. Renovations are designed to bring the facility up to current health and safety and environmental standards and to support its new mission. Improvements include the addition of high-reliability earthquake hardened off-gas and electrical power systems, the upgrading of radiological instrumentation, and the incorporation of advances in contamination control. A major task is the construction of a new equipment repair and decontamination facility in the basement of the building to support operations

INFN Camera demonstrator for the Cherenkov Telescope Array

CERN Document Server

Ambrosi, G; Aramo, C.; Bertucci, B.; Bissaldi, E.; Bitossi, M.; Brasolin, S.; Busetto, G.; Carosi, R.; Catalanotti, S.; Ciocci, M.A.; Consoletti, R.; Da Vela, P.; Dazzi, F.; De Angelis, A.; De Lotto, B.; de Palma, F.; Desiante, R.; Di Girolamo, T.; Di Giulio, C.; Doro, M.; D'Urso, D.; Ferraro, G.; Ferrarotto, F.; Gargano, F.; Giglietto, N.; Giordano, F.; Giraudo, G.; Iacovacci, M.; Ionica, M.; Iori, M.; Longo, F.; Mariotti, M.; Mastroianni, S.; Minuti, M.; Morselli, A.; Paoletti, R.; Pauletta, G.; Rando, R.; Fernandez, G. Rodriguez; Rugliancich, A.; Simone, D.; Stella, C.; Tonachini, A.; Vallania, P.; Valore, L.; Vagelli, V.; Verzi, V.; Vigorito, C.

2015-01-01

The Cherenkov Telescope Array is a world-wide project for a new generation of ground-based Cherenkov telescopes of the Imaging class with the aim of exploring the highest energy region of the electromagnetic spectrum. With two planned arrays, one for each hemisphere, it will guarantee a good sky coverage in the energy range from a few tens of GeV to hundreds of TeV, with improved angular resolution and a sensitivity in the TeV energy region better by one order of magnitude than the currently operating arrays. In order to cover this wide energy range, three different telescope types are envisaged, with different mirror sizes and focal plane features. In particular, for the highest energies a possible design is a dual-mirror Schwarzschild-Couder optical scheme, with a compact focal plane. A silicon photomultiplier (SiPM) based camera is being proposed as a solution to match the dimensions of the pixel (angular size of ~ 0.17 degrees). INFN is developing a camera demonstrator made by 9 Photo Sensor Modules (PSMs...

Combining innovative technology demonstrations with dense nonaqueous phase liquids cleanup

International Nuclear Information System (INIS)

Hagood, M.C.; Koegler, K.J.; Rohay, V.J.; Trent, S.J.; Stein, S.L.; Brouns, T.M.; McCabe, G.H.; Tomich, S.

1993-05-01

Radioactively contaminated acidic aqueous wastes and organic liquids were discharged to the soil column at three disposal sites within the 200 West Area of the Hanford Site, Washington. As a result, a portion of the underlying groundwater is contaminated with carbon tetrachloride several orders of magnitude above the maximum contaminant level accepted for a drinking water supply. Treatability testing and cleanup actions have been initiated to remove the contamination from both the unsaturated soils to minimize further groundwater contamination and the groundwater itself. To expedite cleanup, innovative technologies for (1) drilling, (2) site characterization, (3) monitoring, (4) well field development, and (5) contaminant treatment are being demonstrated and subsequently used where possible to improve the rates and cost savings associated with the removal of carbon tetrachloride from the soils and groundwater

AVN-322 is a Safe Orally Bio-Available Potent and Highly Selective Antagonist of 5-HT6R with Demonstrated Ability to Improve Impaired Memory in Animal Models.

Science.gov (United States)

Ivachtchenko, Alexandre V; Ivanenkov, Yan A; Veselov, Mark S; Okun, I M

2017-01-01

In recent years, 5-hydroxytryptamine subtype 6 receptor (5-HT6 receptor, 5- HT6R) has emerged as a promising therapeutic target for the treatment of neuropathological disorders, including Alzheimer's disease (AD) and schizophrenia. 5-HT6 receptors were hypothesized to be implicated in the processes of learning, memory, and cognition with 5-HT6R antagonists being effective in animal models of cognition and memory impairment. Several selective 5-HT6R ligands are currently undergoing clinical trials for treatment of AD. We describe results of preclinical development of a novel and highly selective and potent 5- HT6R antagonist, AVN-322, as a clinical candidate for the treatment of AD to improve concurrent debilitation of memory and cognition in the AD patients, and schizophrenia as a substance with antipsychotic effect. In the manuscript, we present its in vitro and vivo efficacy, ADME, pharmacokinetics in animals and in humans, and toxicity. While having high binding affinity in medium picomolar range, the lead compound demonstrates substantially better selectivity index then the reference drug candidates currently being tested in clinical studies. AVN-322 showed high oral bioavailability and favorable blood-brain barrier (BBB) penetration. In vivo testing revealed its clear cognition enhancing effect. AVN-322 significantly restored both scopolamine- and MK-801-induced cognitive dysfunction and demonstrated antipsychotic potential. Taking into account its good safety profile and favorable pharmacokinetics, AVN-322 can be reasonably considered as a novel drug candidate for the treatment of neurological disorders such as AD and/or schizophrenia. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Guidance manual for conducting technology demonstration activities

International Nuclear Information System (INIS)

Jolley, R.L.; Morris, M.I.; Singh, S.P.N.

1991-12-01

This demonstration guidance manual has been prepared to assist Martin Marietta Energy Systems, Inc. (Energy Systems), staff in conducting demonstrations. It is prepared in checklist style to facilitate its use and assumes that Energy Systems personnel have project management responsibility. In addition to a detailed step-by-step listing of procedural considerations, a general checklist, logic flow diagram, and several examples of necessary plans are included to assist the user in developing an understanding of the many complex activities required to manage technology demonstrations. Demonstrations are pilot-scale applications of often innovative technologies to determine the commercial viability of the technologies to perform their designed function. Demonstrations are generally conducted on well-defined problems for which existing technologies or processes are less than satisfactory in terms of effectiveness, cost, and/or regulatory compliance. Critically important issues in demonstration management include, but are not limited to, such factors as communications with line and matrix management and with the US Department of Energy (DOE) and Energy Systems staff responsible for management oversight, budgetary and schedule requirements, regulatory compliance, and safety

Guidance manual for conducting technology demonstration activities

Energy Technology Data Exchange (ETDEWEB)

Jolley, Robert L.; Morris, Michael I.; Singh, Suman P.N.

1991-12-01

This demonstration guidance manual has been prepared to assist Martin Marietta Energy Systems, Inc. (Energy Systems), staff in conducting demonstrations. It is prepared in checklist style to facilitate its use and assumes that Energy Systems personnel have project management responsibility. In addition to a detailed step-by-step listing of procedural considerations, a general checklist, logic flow diagram, and several examples of necessary plans are included to assist the user in developing an understanding of the many complex activities required to manage technology demonstrations. Demonstrations are pilot-scale applications of often innovative technologies to determine the commercial viability of the technologies to perform their designed function. Demonstrations are generally conducted on well-defined problems for which existing technologies or processes are less than satisfactory in terms of effectiveness, cost, and/or regulatory compliance. Critically important issues in demonstration management include, but are not limited to, such factors as communications with line and matrix management and with the US Department of Energy (DOE) and Energy Systems staff responsible for management oversight, budgetary and schedule requirements, regulatory compliance, and safety.

Long-term management of high-level radioactive waste. The meaning of a demonstration

International Nuclear Information System (INIS)

1983-01-01

The ''demonstration'' of the safe management of high level radioactive waste is a prerequisite for the further development of nuclear energy. It is therefore essential to be clear about both the meaning of the term ''demonstration'' and the practical means to satisfy this request. In the complex sequence of operations necessary to the safe management of high level waste, short term activities can be directly demonstrated. For longer term activities, such as the long term isolation of radioactive waste in deep undergroung structures, demonstration must be indirect. The ''demonstration'' of deep underground disposal for high level radioactive waste involves two steps: one direct, to prove that the system could be built, operated and closed safely and at acceptable costs, and one indirect, to make a convincing evaluation of the system's performance and long term safety on the basis of predictive analyses confirmed by a body of varied technical and scienfic data, much of it deriving from experimental work. The assessment of the evidence collected from current operations, existing experience in related fields and specific research and development activities, calls for specialized scientific expertise. Uncertainties in far future situations and probabilistic events can be taken into account in a scientific assessment. Competent national authorithies will have to satisfy themselves that the proposed waste management solutions can meet long term safety objectives. An element of judgement will always be needed in determining the acceptability of a waste disposal concept. However, the level of confidence in our ability to predict the performance of waste management systems will increase as supporting evidence is collected from current research and development activities and as our predictive techniques improve

Lunar Water Resource Demonstration

Science.gov (United States)

Muscatello, Anthony C.

2008-01-01

In cooperation with the Canadian Space Agency, the Northern Centre for Advanced Technology, Inc., the Carnegie-Mellon University, JPL, and NEPTEC, NASA has undertaken the In-Situ Resource Utilization (ISRU) project called RESOLVE. This project is a ground demonstration of a system that would be sent to explore permanently shadowed polar lunar craters, drill into the regolith, determine what volatiles are present, and quantify them in addition to recovering oxygen by hydrogen reduction. The Lunar Prospector has determined these craters contain enhanced hydrogen concentrations averaging about 0.1%. If the hydrogen is in the form of water, the water concentration would be around 1%, which would translate into billions of tons of water on the Moon, a tremendous resource. The Lunar Water Resource Demonstration (LWRD) is a part of RESOLVE designed to capture lunar water and hydrogen and quantify them as a backup to gas chromatography analysis. This presentation will briefly review the design of LWRD and some of the results of testing the subsystem. RESOLVE is to be integrated with the Scarab rover from CMIJ and the whole system demonstrated on Mauna Kea on Hawaii in November 2008. The implications of lunar water for Mars exploration are two-fold: 1) RESOLVE and LWRD could be used in a similar fashion on Mars to locate and quantify water resources, and 2) electrolysis of lunar water could provide large amounts of liquid oxygen in LEO, leading to lower costs for travel to Mars, in addition to being very useful at lunar outposts.

42 CFR 416.43 - Conditions for coverage-Quality assessment and performance improvement.

Science.gov (United States)

2010-10-01

..., an ongoing program that demonstrates measurable improvement in patient health outcomes, and improves patient safety by using quality indicators or performance measures associated with improved health outcomes and by the identification and reduction of medical errors. (2) The ASC must measure, analyze, and...

COMMERCIALIZATION DEMONSTRATION OF MID-SIZED SUPERCONDUCTING MAGNETIC ENERGY STORAGE TECHNOLOGY FOR ELECTRIC UTILITYAPPLICATIONS

Energy Technology Data Exchange (ETDEWEB)

CHARLES M. WEBER

2008-06-24

As an outgrowth of the Technology Reinvestment Program of the 1990’s, an Agreement was formed between BWXT and the DOE to promote the commercialization of Superconducting Magnetic Energy Storage (SMES) technology. Business and marketing studies showed that the performance of electric transmission lines could be improved with this SMES technology by stabilizing the line thereby allowing the reserved stability margin to be used. One main benefit sought was to double the capacity and the amount of energy flow on an existing transmission line by enabling the use of the reserved stability margin, thereby doubling revenue. Also, electrical disturbances, power swings, oscillations, cascading disturbances and brown/black-outs could be mitigated and rendered innocuous; thereby improving power quality and reliability. Additionally, construction of new transmission lines needed for increased capacity could be delayed or perhaps avoided (with significant savings) by enabling the use of the reserved stability margin of the existing lines. Two crucial technical aspects were required; first, a large, powerful, dynamic, economic and reliable superconducting magnet, capable of oscillating power flow was needed; and second, an electrical power interface and control to a transmission line for testing, demonstrating and verifying the benefits and features of the SMES system was needed. A project was formed with the goals of commercializing the technology by demonstrating SMES technology for utility applications and to establish a domestic capability for manufacturing large superconducting magnets for both commercial and defense applications. The magnet had very low AC losses to support the dynamic and oscillating nature of the stabilizing power flow. Moreover, to economically interface to the transmission line, the magnet had the largest operating voltage ever made. The manufacturing of that design was achieved by establishing a factory with newly designed and acquired equipment

Tethered elevator and platforms as space station facilities: Systems studies and demonstrative experiments

Science.gov (United States)

1986-01-01

Several key concepts of the science and applications tethered platforms were studied. Some conclusions reached are herein listed. Tether elevator and platform could improve the space station scientific and applicative capabilities. The space elevator presents unique characteristics as microgravity facility and as a tethered platform servicing vehicle. Pointing platforms could represent a new kind of observation facility for large class of payloads. The dynamical, control and technological complexity of these concepts advised demonstrative experiments. The on-going tethered satellite system offers the opportunity to perform such experiments. And feasibility studies are in progress.

Launch Vehicle Demonstrator Using Shuttle Assets

Science.gov (United States)

Threet, Grady E., Jr.; Creech, Dennis M.; Philips, Alan D.; Water, Eric D.

2011-01-01

The Marshall Space Flight Center Advanced Concepts Office (ACO) has the leading role for NASA s preliminary conceptual launch vehicle design and performance analysis. Over the past several years the ACO Earth-to-Orbit Team has evaluated thousands of launch vehicle concept variations for a multitude of studies including agency-wide efforts such as the Exploration Systems Architecture Study (ESAS), Constellation, Heavy Lift Launch Vehicle (HLLV), Heavy Lift Propulsion Technology (HLPT), Human Exploration Framework Team (HEFT), and Space Launch System (SLS). NASA plans to continue human space exploration and space station utilization. Launch vehicles used for heavy lift cargo and crew will be needed. One of the current leading concepts for future heavy lift capability is an inline one and a half stage concept using solid rocket boosters (SRB) and based on current Shuttle technology and elements. Potentially, the quickest and most cost-effective path towards an operational vehicle of this configuration is to make use of a demonstrator vehicle fabricated from existing shuttle assets and relying upon the existing STS launch infrastructure. Such a demonstrator would yield valuable proof-of-concept data and would provide a working test platform allowing for validated systems integration. Using shuttle hardware such as existing RS-25D engines and partial MPS, propellant tanks derived from the External Tank (ET) design and tooling, and four-segment SRB s could reduce the associated upfront development costs and schedule when compared to a concept that would rely on new propulsion technology and engine designs. There are potentially several other additional benefits to this demonstrator concept. Since a concept of this type would be based on man-rated flight proven hardware components, this demonstrator has the potential to evolve into the first iteration of heavy lift crew or cargo and serve as a baseline for block upgrades. This vehicle could also serve as a demonstration

The Simplest Demonstration on Acoustic Beats

Science.gov (United States)

Ganci, Alessio; Ganci, Salvatore

2015-01-01

The classical demonstration experiment on acoustic beats using two signal generators and a dual trace oscilloscope is an important ingredient in teaching the subject. This short laboratory note aims to point out what may be the simplest demonstrative experiment on acoustic beats to carry out in a classroom without employing any lab apparatus.

WiFi RFID demonstration for resource tracking in a statewide disaster drill.

Science.gov (United States)

Cole, Stacey L; Siddiqui, Javeed; Harry, David J; Sandrock, Christian E

2011-01-01

To investigate the capabilities of Radio Frequency Identification (RFID) tracking of patients and medical equipment during a simulated disaster response scenario. RFID infrastructure was deployed at two small rural hospitals, in one large academic medical center and in two vehicles. Several item types from the mutual aid equipment list were selected for tracking during the demonstration. A central database server was installed at the UC Davis Medical Center (UCDMC) that collected RFID information from all constituent sites. The system was tested during a statewide disaster drill. During the drill, volunteers at UCDMC were selected to locate assets using the traditional method of locating resources and then using the RFID system. This study demonstrated the effectiveness of RFID infrastructure in real-time resource identification and tracking. Volunteers at UCDMC were able to locate assets substantially faster using RFID, demonstrating that real-time geolocation can be substantially more efficient and accurate than traditional manual methods. A mobile, Global Positioning System (GPS)-enabled RFID system was installed in a pediatric ambulance and connected to the central RFID database via secure cellular communication. This system is unique in that it provides for seamless region-wide tracking that adaptively uses and seamlessly integrates both outdoor cellular-based mobile tracking and indoor WiFi-based tracking. RFID tracking can provide a real-time picture of the medical situation across medical facilities and other critical locations, leading to a more coordinated deployment of resources. The RFID system deployed during this study demonstrated the potential to improve the ability to locate and track victims, healthcare professionals, and medical equipment during a region-wide disaster.

Flexible-Rotor Balancing Demonstration

Science.gov (United States)

Giordano, J.; Zorzi, E.

1986-01-01

Report describes method for balancing high-speed rotors at relatively low speeds and discusses demonstration of method on laboratory test rig. Method ensures rotor brought up to speeds well over 20,000 r/min smoothly, without excessive vibration amplitude at critical speeds or at operating speed.

A Magnetic Circuit Demonstration.

Science.gov (United States)

Vanderkooy, John; Lowe, June

1995-01-01

Presents a demonstration designed to illustrate Faraday's, Ampere's, and Lenz's laws and to reinforce the concepts through the analysis of a two-loop magnetic circuit. Can be made dramatic and challenging for sophisticated students but is suitable for an introductory course in electricity and magnetism. (JRH)

Large-scale demonstration and deployment project at Los Alamos National Laboratory

International Nuclear Information System (INIS)

Brown, S.; McFee, J.; Broom, C.; Dugger, H.; Stallings, E.

1999-01-01

Established by the US Department of Energy (DOE) Environmental Management program through its Office of Science and Technology, the Deactivation and Decommissioning Focus Area is developing answers to the technological problems that hinder Environmental Management's extensive cleanup efforts. The optimized application of technologies to ongoing nuclear facility decontamination and dismantlement is critical in meeting the challenge of decommissioning approximately 9,000 buildings and structures within the DOE complex. The significant technical and economic concerns in this area underscore a national imperative for the qualification and timely delivery of cost-reduction technologies and management approaches to meet federal and private needs. At Los Alamos National Laboratory (LANL), a Large-Scale Demonstration and Deployment Project (LSDDP) has been established to facilitate demonstration and deployment of technologies for the characterization, decontamination, and volume reduction of oversized metallic waste, mostly in the form of gloveboxes contaminated with transuranic radionuclides. The LANL LSDDP is being managed by an integrated contractor team (ICT) consisting of IT Corporation, ICF Incorporated, and Florida International University and includes representation from LANL's Environmental Management Program Office. The ICT published in the Commerce Business Daily a solicitation for interest for innovative technologies capable of improving cost and performance of the baseline process. Each expression of interest response was evaluated and demonstration contract negotiations are under way for those technologies expected to be capable of meeting the project objectives. This paper discusses management organization and approach, the results of the technology search, the technology selection methodology, the results of the selection process, and future plans for the program

Reactor-vessel-sectioning demonstration

International Nuclear Information System (INIS)

Lundgren, R.A.

1981-09-01

A technical demonstration was successfully completed of simulated reactor vessel sectioning using the combined techniques of air arc gouging and flame cutting. A 4-ft x 3-ft x 9-in. thick sample was fabricated of A36 carbon steel to simulate a reactor vessel wall. A 1/4-in. layer of stainless steel (SS) was tungsten inert gas (TIG)-welded to the carbon steel. Several techniques were considered to section the simulated reactor vessel; air arc gouging was selected to penetrate the stainless steel, and flame cutting was selected to sever the carbon steel. Three sectioning operations were demonstrated. For all three, the operating parameters were the same; but the position of the sample was varied. For the first cut, the sample was placed in a horizontal position, and it was successfully severed from the SS side. For the second cut, the sample was turned over and cut from the carbon steel side. Cutting from the carbon steel side has the advantages of cost reduction

Demonstration of near-real-time accounting: the AGNS 1980-81 miniruns

International Nuclear Information System (INIS)

Dayem, H.A.; Baker, A.L.; Cobb, D.D.; Hakkila, E.A.; Ostenak, C.A.

1984-01-01

Near-real-time nuclear materials accounting was demonstrated in a series of experiments at the Allied-General Nuclear Services (AGNS) Barnwell Nuclear Fuels Plant. For each experiment, the second and third plutonium cycles were operated continuously for 1 wk processing uranium solutions. Process data were collected in near-real time by the AGNS computerized nuclear materials control and accounting system and were analyzed for uranium removals using decision analysis techniques. Although the measurement system primarily consisted of process-monitoring measurements that were not optimized for near-real-time accounting, the results of uranium-removal tests showed that removals and unexpected losses from the process area can be detected. Los Alamos used process-grade measurements to close hourly materials balances. Loss-detection sensitivities for 1 day of between 4 and 18 kg of uranium, at 50% detection probability and 2.5% false-alarm probability, were calculated for selected accounting areas. Using pulsed-column inventory estimators, we calculated a total four-column inventory that was within 10% of column dump measurements. Loss-detection sensitivity could be improved by incorporating online waste stream measurements, improving laboratory measurements for process streams, and refining the pulsed-column inventory estimates

Status of IFR fuel cycle demonstration

International Nuclear Information System (INIS)

Lineberry, M.J.; Phipps, R.D.; McFarlane, H.F.

1993-01-01

The next major step in Argonne's Integral Fast Reactor (IFR) Program is demonstration of the pyroprocess fuel cycle, in conjunction with continued operation of EBR-II. The Fuel Cycle Facility (FCF) is being readied for this mission. This paper will address the status of facility systems and process equipment, the initial startup experience, and plans for the demonstration program

How to demonstrate adequacy of protection against a core melt

International Nuclear Information System (INIS)

Hock, R.

1996-01-01

After the Chernobyl accident the public - and consequently the politicians - in Western countries requested improvements in safety for future reactors even in those designs where the type of accident which had destroyed the Chernobyl plant is excluded by fundamental physics. When the major German and French suppliers of nuclear power stations, Siemens and Framatome, decided to develop jointly a next generation reactor type, this political 'request' had to be taken into account. It was decided to include safety features to mitigate the consequences of a core melt - the severest type of accident in a western light water reactor - should it occur despite the many other safety features which are included in this design in order to reduce the probability of occurrence of this type of event to extremely low values. The question arose: How to demonstrate the adequacy of his additional protection? It was evident that the methodology proposed by ICRP namely to demonstrate that the risk of individual members of the public caused by 'probabilistic events' is sufficiently low, could not be used: Due to the low probability of occurrence the contribution of this kind of accident to the risk of any average member of a critical group would already be sufficiently low even if there were no additional countermeasures. In addition, this approach would not cover severe societal effects potentially caused by such an accident. We therefore introduced a different methodology in order to demonstrate the adequacy of additional design features which are only required 'just in case': The consequences of such an unlikely but nevertheless very severe event shall be restricted to the plant itself. Severe consequences outside the immediate vicinity of the plant shall be excluded by the design. (author)

Improving voluntary medical male circumcision standards ...

African Journals Online (AJOL)

Voluntary medical male circumcision (VMMC) has been demonstrated to reduce the transmission of HIV by 60%. Scaling up VMMC services requires that they be of high quality, socially accepted, and effective. We evaluated an intervention aimed at improving VMMC standards adherence and patient follow-up rates in nine ...

Visual Electricity Demonstrator

Science.gov (United States)

Lincoln, James

2017-09-01

The Visual Electricity Demonstrator (VED) is a linear diode array that serves as a dynamic alternative to an ammeter. A string of 48 red light-emitting diodes (LEDs) blink one after another to create the illusion of a moving current. Having the current represented visually builds an intuitive and qualitative understanding about what is happening in a circuit. In this article, I describe several activities for this device and explain how using this technology in the classroom can enhance the understanding and appreciation of physics.

Test and Demonstration Assets of New Mexico

Energy Technology Data Exchange (ETDEWEB)

None

2008-03-31

This document was developed by the Arrowhead Center of New Mexico State University as part of the National Security Preparedness Project (NSPP), funded by a DOE/NNSA grant. The NSPP has three primary components: business incubation, workforce development, and technology demonstration and validation. The document contains a survey of test and demonstration assets in New Mexico available for external users such as small businesses with security technologies under development. Demonstration and validation of national security technologies created by incubator sources, as well as other sources, are critical phases of technology development. The NSPP will support the utilization of an integrated demonstration and validation environment.

Performance improvement program: goals and experience

International Nuclear Information System (INIS)

Guglielmi, F.

2015-01-01

Following long 54 month refurbishment outage at Point Lepreau Generating Station, operational performance had fallen below industry standards in a number of areas. Leadership development and succession planning had stalled. Operational focus was low primarily due to the construction focus during refurbishment. Condition of balance of plant was poor including several long standing deficiencies. In order to improve performance, the site implemented a framework based on INPO 12-011: Focus on Improving Behaviours; Set common goals and demonstrate results; Align and engage the organization; Drive to achieve high levels of performance and sustain performance.

Performance improvement program: goals and experience

Energy Technology Data Exchange (ETDEWEB)

Guglielmi, F. [Point Lepreau Generating Station, Maces Bay, New Brunswick (Canada)

2015-07-01

Following long 54 month refurbishment outage at Point Lepreau Generating Station, operational performance had fallen below industry standards in a number of areas. Leadership development and succession planning had stalled. Operational focus was low primarily due to the construction focus during refurbishment. Condition of balance of plant was poor including several long standing deficiencies. In order to improve performance, the site implemented a framework based on INPO 12-011: Focus on Improving Behaviours; Set common goals and demonstrate results; Align and engage the organization; Drive to achieve high levels of performance and sustain performance.

Transformed composite sequences for improved qubit addressing

Science.gov (United States)

Merrill, J. True; Doret, S. Charles; Vittorini, Grahame; Addison, J. P.; Brown, Kenneth R.

2014-10-01

Selective laser addressing of a single atom or atomic ion qubit can be improved using narrow-band composite pulse sequences. We describe a Lie-algebraic technique to generalize known narrow-band sequences and introduce sequences related by dilation and rotation of sequence generators. Our method improves known narrow-band sequences by decreasing both the pulse time and the residual error. Finally, we experimentally demonstrate these composite sequences using 40Ca+ ions trapped in a surface-electrode ion trap.

78 FR 11737 - Improving Critical Infrastructure Cybersecurity

Science.gov (United States)

2013-02-19

..., security, business confidentiality, privacy, and civil liberties. We can achieve these goals through a... security measures or controls on business confidentiality, and to protect individual privacy and civil... critical infrastructure demonstrate the need for improved cybersecurity. The cyber threat to critical...

Improving health visitor emollient prescribing using a CQUIN-based approach.

Science.gov (United States)

Brooks, Christina; Khatau, Tejas

2015-12-01

Prescribing is an essential element of health visiting practice. This initiative used the payment framework of Commissioning for Quality and Innovation (CQUIN) to develop health visiting practice across a large health visiting workforce in the East Midlands. A focus on emollient prescribing practice was agreed and a guidance booklet regarding preferred emollient products was produced, based on the local formulary Each health visitor benefitted from receiving additional training and was given a guidance booklet to inform their practice. Targets were set for each quarter to demonstrate an improved prescribing adherence to the preferred product list.The targets were achieved for each quarter. Prescribing rates and confidence improved across the service. Therefore, it was demonstrated that specific guidance and ongoing support can improve prescribing practice within the health visiting service.

Use of the CT component of PET-CT to improve PET-MR registration: demonstration in soft-tissue sarcoma

International Nuclear Information System (INIS)

Somer, Edward J; Benatar, Nigel A; O'Doherty, Michael J; Smith, Mike A; Marsden, Paul K

2007-01-01

We have investigated improvements to PET-MR image registration offered by PET-CT scanning. Ten subjects with suspected soft-tissue sarcomas were scanned with an in-line PET-CT and a clinical MR scanner. PET to CT, CT to MR and PET to MR image registrations were performed using a rigid-body external marker technique and rigid and non-rigid voxel-similarity algorithms. PET-MR registration was also performed using transformations derived from the registration of CT to MR. The external marker technique gave fiducial registration errors of 2.1 mm, 5.1 mm and 5.3 mm for PET-CT, PET-MR and CT-MR registration. Target registration errors were 3.9 mm, 9.0 mm and 9.3 mm, respectively. Voxel-based algorithms were evaluated by measuring the distance between corresponding fiducials after registration. Registration errors of 6.4 mm, 14.5 mm and 9.5 mm, respectively, for PET-CT, PET-MR and CT-MR were observed for rigid-body registration while non-rigid registration gave errors of 6.8 mm, 16.3 mm and 7.6 mm for the same modality combinations. The application of rigid and non-rigid CT to MR transformations to accompanying PET data gives significantly reduced PET-MR errors of 10.0 mm and 8.5 mm, respectively. Visual comparison by two independent observers confirmed the improvement over direct PET-MR registration. We conclude that PET-MR registration can be more accurately and reliably achieved using the hybrid technique described than through direct rigid-body registration of PET to MR

Calderon cokemaking process/demonstration project

International Nuclear Information System (INIS)

Albert Calderon

1998-01-01

This project deals with the demonstration of a coking process using proprietary technology of Calderon, with the following objectives geared to facilitate commercialization: (i) making coke of such quality as to be suitable for use in hard-driving, large blast furnaces; (ii) providing proof that such process is continuous and environmentally closed to prevent emissions; (iii) demonstrating that high-coking-pressure (non-traditional) coal blends which cannot be safely charged into conventional by-product coke ovens can be used in the Calderon process; and (iv) demonstrating that coke can be produced economically, at a level competitive with coke imports. The activities of the past quarter were focused on the following: Consolidation of the project team-players; Recruiting Koppers Industries as an additional stakeholder; Developing a closed system for the production of binder pitch from tar in the Calderon coking process as the incentive for Koppers to join the team; Gathering appropriate equipment for conducting a set of experiments at bench scale to simulate tar quality produced from the Calderon coking process for the production of binder pitch; and Further progress made in the design of the commercial coking reactor

Buried waste integrated demonstration technology integration process

International Nuclear Information System (INIS)

Ferguson, J.S.; Ferguson, J.E.

1992-04-01

A Technology integration Process was developed for the Idaho National Energy Laboratories (INEL) Buried Waste Integrated Demonstration (BWID) Program to facilitate the transfer of technology and knowledge from industry, universities, and other Federal agencies into the BWID; to successfully transfer demonstrated technology and knowledge from the BWID to industry, universities, and other Federal agencies; and to share demonstrated technologies and knowledge between Integrated Demonstrations and other Department of Energy (DOE) spread throughout the DOE Complex. This document also details specific methods and tools for integrating and transferring technologies into or out of the BWID program. The document provides background on the BWID program and technology development needs, demonstrates the direction of technology transfer, illustrates current processes for this transfer, and lists points of contact for prospective participants in the BWID technology transfer efforts. The Technology Integration Process was prepared to ensure compliance with the requirements of DOE's Office of Technology Development (OTD)

Demonstrating the Gas Laws.

Science.gov (United States)

Holko, David A.

1982-01-01

Presents a complete computer program demonstrating the relationship between volume/pressure for Boyle's Law, volume/temperature for Charles' Law, and volume/moles of gas for Avagadro's Law. The programing reinforces students' application of gas laws and equates a simulated moving piston to theoretical values derived using the ideal gas law.…

Improved cosine similarity measures of simplified neutrosophic sets for medical diagnoses.

Science.gov (United States)

Ye, Jun

2015-03-01

In pattern recognition and medical diagnosis, similarity measure is an important mathematical tool. To overcome some disadvantages of existing cosine similarity measures of simplified neutrosophic sets (SNSs) in vector space, this paper proposed improved cosine similarity measures of SNSs based on cosine function, including single valued neutrosophic cosine similarity measures and interval neutrosophic cosine similarity measures. Then, weighted cosine similarity measures of SNSs were introduced by taking into account the importance of each element. Further, a medical diagnosis method using the improved cosine similarity measures was proposed to solve medical diagnosis problems with simplified neutrosophic information. The improved cosine similarity measures between SNSs were introduced based on cosine function. Then, we compared the improved cosine similarity measures of SNSs with existing cosine similarity measures of SNSs by numerical examples to demonstrate their effectiveness and rationality for overcoming some shortcomings of existing cosine similarity measures of SNSs in some cases. In the medical diagnosis method, we can find a proper diagnosis by the cosine similarity measures between the symptoms and considered diseases which are represented by SNSs. Then, the medical diagnosis method based on the improved cosine similarity measures was applied to two medical diagnosis problems to show the applications and effectiveness of the proposed method. Two numerical examples all demonstrated that the improved cosine similarity measures of SNSs based on the cosine function can overcome the shortcomings of the existing cosine similarity measures between two vectors in some cases. By two medical diagnoses problems, the medical diagnoses using various similarity measures of SNSs indicated the identical diagnosis results and demonstrated the effectiveness and rationality of the diagnosis method proposed in this paper. The improved cosine measures of SNSs based on cosine

Supercompaction/grouting demonstration project: Final report

International Nuclear Information System (INIS)

1987-01-01

The purpose of this supercompaction demonstration project was to allow Martin Marietta Energy Systems, Inc. (The Company), to obtain cost analysis and performance information on volume reduction and waste encapsulation of solid, low-level contaminated waste (SLW). Ultimately, this information will be used to help define a waste disposal process for SLW that is acceptable to regulatory agencies and the US Department of Energy, Oak Ridge Operations (DOE/ORO). The technical objectives of the demonstration project were: (1) to obtain detailed performance data on each of the compacted barrels; (2) evaluate operating performance problems that may have occurred; (3) describe in detail the compaction and encapsulation process; and (4) to obtain operating cost data for the performance of this demonstration

Prototypical Consolidation Demonstration Project: Final report

International Nuclear Information System (INIS)

Gili, J.A.; Poston, V.K.

1993-11-01

This is the final report of the Prototypical Consolidation Demonstration Project, which was funded by the US Department of Energy's Office of Civilian Radioactive Waste Management. The project had two objectives: (a) to develop and demonstrate a prototype of production-scale equipment for the dry, horizontal consolidation and packaging of spent nuclear fuel rods from commercial boiling water reactor and pressurized water reactor fuel assemblies, and (b) to report the development and demonstration results to the US Department of Energy, Idaho Operations Office. This report summarizes the activities and conclusions of the project management contractor, EG ampersand G Idaho, Inc., and the fabrication and testing contractor, NUS Corporation (NUS). The report also presents EG ampersand G Idaho's assessments of the equipment and procedures developed by NUS

How to Measure and Interpret Quality Improvement Data.

Science.gov (United States)

McQuillan, Rory Francis; Silver, Samuel Adam; Harel, Ziv; Weizman, Adam; Thomas, Alison; Bell, Chaim; Chertow, Glenn M; Chan, Christopher T; Nesrallah, Gihad

2016-05-06

This article will demonstrate how to conduct a quality improvement project using the change idea generated in "How To Use Quality Improvement Tools in Clinical Practice: How To Diagnose Solutions to a Quality of Care Problem" by Dr. Ziv Harel and colleagues in this Moving Points feature. This change idea involves the introduction of a nurse educator into a CKD clinic with a goal of increasing rates of patients performing dialysis independently at home (home hemodialysis or peritoneal dialysis). Using this example, we will illustrate a Plan-Do-Study-Act (PDSA) cycle in action and highlight the principles of rapid cycle change methodology. We will then discuss the selection of outcome, process, and balancing measures, and the practicalities of collecting these data in the clinic environment. We will also introduce the PDSA worksheet as a practical way to oversee the progress of a quality improvement project. Finally, we will demonstrate how run charts are used to visually illustrate improvement in real time, and how this information can be used to validate achievement, respond appropriately to challenges the project may encounter, and prove the significance of results. This article aims to provide readers with a clear and practical framework upon which to trial their own ideas for quality improvement in the clinical setting. Copyright © 2016 by the American Society of Nephrology.

Improving Family Communication.

Science.gov (United States)

Medrano, Vilma; Bonilla, Gladys; Hernández, Ericka; Romanjek, Mariana Harnecker; Gómez, Adriana; Hernández, Jasón; Reyes, Marcela Ríos; Lindenberg, Cathy Strachan

2017-03-01

TeenSmart International harnesses the power and flexibility of technology to empower youth to take personal responsibility for their health and lifestyle choices. Access to the Internet via mobile phones is often cheaper than paying to connect to a wired broadband service, and in rural areas, mobile networks may be the only means of accessing the Internet. This study assessed the feasibility, acceptability, and impact of "cues to action" or brief motivating cell phone text messages to improve adolescent family communication and relationships. A quasi-experimental design using a voluntary sample of 100 Nicaraguan youth at high risk for poor family communication participated. Pre- and posttest quantitative measures using Student t statistical analysis, a focus group, and a participant testimony provided the evaluation evidence. Findings suggest that there are economic and motivational barriers to the use of text messages, but when barriers are eliminated, the behavioral results are positive. Youth who received two weekly text messages over a 6-month period demonstrated statistically significant improvements in family communication perceptions, attitudes, and behaviors, strengthening their family communications and relationships. Brief and personalized text messaging "cues to action" may be a cost-effective intervention to improve adolescent healthy lifestyle behaviors.

Commercial Demonstration of Wood Recovery, Recycling, and Value Adding Technologies

Energy Technology Data Exchange (ETDEWEB)

Auburn Machinery, Inc.

2004-07-15

This commercial demonstration project demonstrated the technical feasibility of converting low-value, underutilized and waste stream solid wood fiber material into higher valued products. With a growing need to increase product/production yield and reduce waste in most sawmills, few recovery operations and practically no data existed to support the viability of recovery operations. Prior to our efforts, most all in the forest products industry believed that recovery was difficult, extremely labor intensive, not cost effective, and that recovered products had low value and were difficult to sell. This project provided an opportunity for many within the industry to see through demonstration that converting waste stream material into higher valued products does in fact offer a solution. Our work, supported by the U.S. Department of Energy, throughout the project aimed to demonstrate a reasonable approach to reducing the millions of recoverable solid wood fiber tons that are annually treated as and converted into low value chips, mulch and fuel. Consequently sawmills continue to suffer from reduced availability of forest resources, higher raw material costs, growing waste disposal problems, increased global competition, and more pressure to operate in an Environmentally Friendly manner. It is our belief (based upon the experience of this project) that the successful mainstreaming of the recovery concept would assist in alleviating this burden as well as provide for a realistically achievable economic benefit to those who would seriously pursue the concept and tap into the rapidly growing ''GREEN'' building marketplace. Ultimately, with participation and aggressive pursuit of the recovery concept, the public would benefit in that: (1) Landfill/disposal waste volume could be reduced adding greater life to existing municipal landfill sites thereby minimizing the need to prematurely license and open added facilities. Also, there would be a cost

Albemarle Sound demonstration study of the national monitoring network for US coastal waters and their tributaries

Science.gov (United States)

Michelle Moorman; Sharon Fitzgerald; Keith Loftin; Elizabeth Fensin

2016-01-01

The U.S. Geological Survey’s (USGS) is implementing a demonstration project in the Albemarle Sound for the National Monitoring Network for U.S. coastal waters and their tributaries. The goal of the National Monitoring Network is to provide information about the health of our oceans and coastal ecosystems and inland influences on coastal waters for improved resource...

Transuranic material recovery in the Integral Fast Reactor fuel cycle demonstration

International Nuclear Information System (INIS)

Benedict, R.W.; Goff, K.M.

1993-01-01

The Integral Fast Reactor is an innovative liquid metal reactor concept that is being developed by Argonne National Laboratory. It takes advantage of the properties of metallic fuel and liquid metal cooling to offer significant improvements in reactor safety, operation, fuel cycle economics, environmental protection, and safeguards. The plans for demonstrating the IFR fuel cycle, including its waste processing options, by processing irradiated fuel from the Experimental Breeder Reactor-II fuel in its associated Fuel Cycle Facility have been developed for the first refining series. This series has been designed to provide the data needed for the further development of the IFR program. An important piece of the data needed is the recovery of TRU material during the reprocessing and waste operations

Design and Demonstration of Emergency Control Modes for Enhanced Engine Performance

Science.gov (United States)

Liu, Yuan; Litt, Jonathan S.; Guo, Ten-Huei

2013-01-01

A design concept is presented for developing control modes that enhance aircraft engine performance during emergency flight scenarios. The benefits of increased engine performance to overall vehicle survivability during these situations may outweigh the accompanied elevated risk of engine failure. The objective involves building control logic that can consistently increase engine performance beyond designed maximum levels based on an allowable heightened probability of failure. This concept is applied to two previously developed control modes: an overthrust mode that increases maximum engine thrust output and a faster response mode that improves thrust response to dynamic throttle commands. This paper describes the redesign of these control modes and presents simulation results demonstrating both enhanced engine performance and robust maintenance of the desired elevated risk level.

Inseparable Phone Books Demonstration

Science.gov (United States)

Balta, Nuri; Çetin, Ali

2017-01-01

This study is aimed at first introducing a well-known discrepant event; inseparable phone books and second, turning it into an experiment for high school or middle school students. This discrepant event could be used especially to indicate how friction force can be effective in producing an unexpected result. Demonstration, discussion, explanation…

Perchlorate Removal, Destruction, and Field Monitoring Demonstration

National Research Council Canada - National Science Library

Coppola, Edward N; Davis, Andrea

2006-01-01

The objectives of this demonstration were to evaluate and demonstrate a complete perchlorate ion exchange process for groundwater that included a unique, regenerable, perchlorate-selective ion exchange resin...

Multiview Projection Using CADKEY Freeze-Frame Demonstrations.

Science.gov (United States)

Kelso, Robert P.; Ziai, M. Reza

1988-01-01

Describes a three-dimensional computer aided design software package, CADKEY, for demonstrating orthographic orthodirectional projection theory to a classroom. Provides several figures for showing the demonstrations. (Author/YP)

Multi-Sensor Improved Sea Surface Temperature (MISST) for GODAE

National Research Council Canada - National Science Library

Gentemann, Chelle L; Wick, Gary A; Cummings, James; Bayler, Eric

2004-01-01

...) sensors and to then demonstrate the impact of these improved sea surface temperatures (SSTs) on operational ocean models, numerical weather prediction, and tropical cyclone intensity forecasting...

ATM Technology Demonstration 1 (ATD-1): EcoDemonstrator ASTAR Guided Arrival Research (EAGAR)

Science.gov (United States)

Roper, Roy

2015-01-01

In Spring 2013, high level NASA and Boeing management were seeking opportunities to collaborate on a flight test activity involving the ecoDemonstrator. The Airspace Systems Program Office identified FIM as a viable candidate. ATD-1 accepted the challenge. Work began in July for a December 2013 flight test.

Final report : Alberta renewable diesel demonstration

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-02-15

The Alberta renewable diesel demonstration (ARDD) was a demonstration project aimed at providing information and operating experience to stakeholders in the diesel fuel industry. The demonstration took renewable diesel from the lab to the road, providing hands-on experience at 2 and 5 per cent blends (B2 in winter and B5 in shoulder and summer seasons). The ARDD fleet consisted of 59 vehicles running on two types of renewable diesel, notably fatty acid methyl ester (FAME) and hydrogenated-derived renewable diesel (HDRD). This report was a summary of the observations of the ARDD. The report provided a general account of the project scope, methods and observations employed in a multi-stakeholder, real-world demonstration of low-level renewable diesel fuels in challenging winter conditions. The purpose of the report was to provide feedback to stakeholders regarding the use of renewable diesel fuels in Canada's on-road diesel fuel market and to confirm the operability of low level renewable diesel blends under the specific conditions tested ensuring full and continuous compliance with CAN/CGSB 3.520. The report discussed Canada's fuel distribution system in western Canada; the blending facility; blending techniques; fuel retail locations; fuel properties; fuel handling; fuel selection; and fuel testing. It was concluded that the ARDD demonstrated that B2 blends of canola methyl ester and 2 per cent blends of hydrogenation derived renewable diesel were fully operable in winter conditions in the study area when cloud points were adjusted to meet CAN/CGSB requirements. 4 refs., 15 tabs., 20 figs., 2 appendices.

Research, development, and demonstration of nickel-iron batteries for electric vehicle propulsion. Annual report for 1980

Energy Technology Data Exchange (ETDEWEB)

1981-03-01

The FY 1980 program continued to involve full-size, prototype cell, module and battery fabrication and evaluation, aimed at advancing the technical capabilities of the nickel-iron battery, while simultaneously reducing its potential cost in materials and process areas. Improved Electroprecipitation Process (EPP) nickel electrodes of design thickness (2.5 mm) are now being prepared that display stable capacities of 23 to 25 Ah for the C/3 drain rate at 200+ test cycles. Iron electrodes of the composite-type are delivering 24 Ah at the target thickness (1.0 mm). Iron electrodes are displaying capacity stability for > 1000 test cycles in continuing 3 plate cell tests. Finished cells have delivered 57 to 61 Wh/kg at C/3, and have demonstrated cyclic stability to 500+ cycles at 80% depth of discharge profiles at Westinghouse. A 6-cell module that demonstrated 239 Ah, 1735 Wh, 48 Wh/kg at the C/3 drain rate has also been evaluated at the National Battery Test Laboratory, ANL. It operated for 327 test cycles, to a level of 161 Ah at the C/3 rate, before being removed from test. Reduction in nickel electrode swelling (and concurrent stack starvation), to improve cycling, continues to be an area of major effort to reach the final battery cycle life objectives. Pasted nickel electrodes continue to show promise for meeting the life objectives while, simultaneously, providing a low manufacturing cost. Refinements have occurred in the areas of cell hardware, module manifolding and cell interconnections. These improvements have been incorporated into the construction and testing of the cells and modules for this program. Temperature tests at 0/sup 0/C were performed on a 6-cell module and showed a decrease in capacity of only 25% in Ah and .29% in Wh as compared to 25/sup 0/C performance. Additional tests are planned to demonstrate performance at -15/sup 0/C and 40/sup 0/C.

Buried Waste Integrated Demonstration FY-93 Deployment Plan

International Nuclear Information System (INIS)

Bonnenberg, R.W.; Heard, R.E.; Milam, L.M.; Watson, L.R.

1993-02-01

The Buried Waste Integrated Demonstration (BWID) is a program funded by the US Department of Energy Office of Technology Development. BWID supports the applied research, development, demonstration, and evaluation of a suite of advanced technologies that together form a comprehensive remediation system for the effective and efficient remediation of buried waste. The fiscal year 1993 effort will deploy seven major field demonstrations at the Idaho National Engineering Laboratory's (INEL's) Radioactive Waste Management Complex Cold Test Pit. These major demonstrations are Remote Characterization System, Remote Excavation System, Overburden Removal, Waste Isolation, Contamination Control Unit, Rapid Monitoring Unit, and Fixation of Soil Surface Contamination. This document is the basic operational planning document for BWID deployment of the INEL field demonstrations. Additional sections deal briefly with four nonINEL field and laboratory demonstrations (Buried Waste Retrieval, Arc Melter Vitrification, Graphite DC Plasma Arc Melter, and Fixed Hearth Plasma Process) and with four INEL laboratory demonstrations (Electrostatic Curtain, Thermal Kinetics, Multiaxis Crane Control System, and Dig-Face Characterization)

North-South Corridor Demonstration Project: Ethical and Logistical Challenges in the Design of a Demonstration Study of Early Antiretroviral Treatment for Long Distance Truck Drivers along a Transport Corridor through South Africa, Zimbabwe, and Zambia

Directory of Open Access Journals (Sweden)

G. B. Gomez

2013-01-01

Full Text Available Background. Long-distance truck drivers are at risk of acquiring and transmitting HIV and have suboptimal access to care. New HIV prevention strategies using antiretroviral drugs to reduce transmission risk (early antiretroviral therapy (ART at CD4 count >350 cells/μL have shown efficacy in clinical trials. Demonstration projects are needed to evaluate “real world” programme effectiveness. We present the protocol for a demonstration study to evaluate the feasibility, acceptability, and cost of an early ART intervention for HIV-positive truck drivers along a transport corridor across South Africa, Zimbabwe, and Zambia, as part of an enhanced strategy to improve treatment adherence and retention in care. Methods and Analysis. This demonstration study would follow an observational cohort of truck drivers receiving early treatment. Our mixed methods approach includes quantitative, qualitative, and economic analyses. Key ethical and logistical issues are discussed (i.e., choice of drug regimen, recruitment of participants, and monitoring of adherence, behavioural changes, and adverse events. Conclusion. Questions specific to the design of tailored early ART programmes are amenable to operational research approaches but present substantial ethical and logistical challenges. Addressing these in demonstration projects can inform policy decisions regarding strategies to reduce health inequalities in access to HIV prevention and treatment programmes.

Review of the Vortec soil remediation demonstration program

International Nuclear Information System (INIS)

Patten, J.S.

1994-01-01

The principal objective of the METC/Vortec program is to develop and demonstrate the effectiveness of the Vortec CMS in remediating soils contaminated with hazardous materials and/or low levels of radionuclides. To convincingly demonstrate the CMS's capability, a Demonstration Plant will be constructed and operated at a DOE site that has a need for the remediation of contamination soil. The following objectives will be met during the program: (1) establish the glass chemistry requirements to achieve vitrification of contaminated soils found at the selected DOE site; (2) complete the design of a fully integrated soil vitrification demonstration plant with a capacity to process 25 TPD of soil; (3) establish the cost of a fully integrated soil demonstration plant with a capacity to process 25 TPD of soil; (4) construct and operate a fully integrated demonstration plant; (5) analyze all influent and effluent streams to establish the partitioning of contaminants and to demonstrate compliance with all applicable health, safety, and environmental requirements; (6) demonstrate that the CMS technology has the capability to produce a vitrified product that will immobilize the hazardous and radionuclide materials consistent with the needs of the specific DOE waste repositories

UNEP Demonstrations of Mercury Emission Reduction at Two Coal-fired Power Plants in Russia

Directory of Open Access Journals (Sweden)

Jozewicz W.

2013-04-01

Full Text Available The United Nations Environment Programme (UNEP partnership area “Mercury releases from coal combustion” (The UNEP Coal Partnership has initiated demonstrations of mercury air emission reduction at two coal-fired power plants in Russia. The first project has modified the wet particulate matter (PM scrubber installed in Toliatti thermal plant to allow for addition of chemical reagents (oxidants into the closedloop liquid spray system. The addition of oxidant resulted in significant improvement of mercury capture from 20% total mercury removal (without the additive up to 60% removal (with the additive. It demonstrates the effectiveness of sorbent injection technologies in conjunction with an electrostatic precipitator (ESP. ESPs are installed at 60%, while wet PM scrubbers are installed at 30% of total coal-fired capacity in Russia. Thus, the two UNEP Coal Partnership projects address the majority of PM emission control configurations occurring in Russia.

Training to Improve Hearing Speech in Noise: Biological Mechanisms

Science.gov (United States)

Song, Judy H.; Skoe, Erika; Banai, Karen

2012-01-01

We investigated training-related improvements in listening in noise and the biological mechanisms mediating these improvements. Training-related malleability was examined using a program that incorporates cognitively based listening exercises to improve speech-in-noise perception. Before and after training, auditory brainstem responses to a speech syllable were recorded in quiet and multitalker noise from adults who ranged in their speech-in-noise perceptual ability. Controls did not undergo training but were tested at intervals equivalent to the trained subjects. Trained subjects exhibited significant improvements in speech-in-noise perception that were retained 6 months later. Subcortical responses in noise demonstrated training-related enhancements in the encoding of pitch-related cues (the fundamental frequency and the second harmonic), particularly for the time-varying portion of the syllable that is most vulnerable to perceptual disruption (the formant transition region). Subjects with the largest strength of pitch encoding at pretest showed the greatest perceptual improvement. Controls exhibited neither neurophysiological nor perceptual changes. We provide the first demonstration that short-term training can improve the neural representation of cues important for speech-in-noise perception. These results implicate and delineate biological mechanisms contributing to learning success, and they provide a conceptual advance to our understanding of the kind of training experiences that can influence sensory processing in adulthood. PMID:21799207

Managing Cultural Variation in Software Process Improvement

DEFF Research Database (Denmark)

Müller, Sune Dueholm; Kræmmergaard, Pernille; Mathiassen, Lars

The scale and complexity of change in software process improvement (SPI) are considerable and managerial attention to organizational culture during SPI can therefore potentially contribute to successful outcomes. However, we know little about the impact of variations in organizational subculture...... CMMI level 2 as planned, ASY struggled to implement even modest improvements. To explain these differences, we analyzed the underlying organizational culture within ISY and ASY using two different methods for subculture assessment. The study demonstrates how variations in culture across software...

Improvement Performance of the Filling Step in Injection Mold through Vibration

Directory of Open Access Journals (Sweden)

Trejo-Hernández M.

2012-10-01

Full Text Available This paper shows the flow improvement in the filling step of the polymer injection process due to the polymer excitation though vibration. This process can be split up into three main steps: filling, pocking and cooling. Several mechanical and aesthetic properties of the finished product can be changed in the filling step. The objective of this investigation is to demonstrate the improvement in the filling mold under vibration without adding chemical products. To reach this result, an experimental mold was designed and manufactured in which a vibration device was coupled; it was possible to demonstrate the vibration advantage through this process. Moreover, a heuristic methodology was proposed for the experiment which shows an improvement in the filling process with frequencies close to 3 Hz.

Postirradiation examination of ORR demonstration elements

International Nuclear Information System (INIS)

Snelgrove, J.L.; Copeland, G.L.; Hofman, G.L.

1991-01-01

Postirradiation examinations of selected U 3 Si 2 fuel elements fabricated by B and W, CERCA, and NUKEM and irradiated during the whole core demonstration in the Oak Ridge Research Reactor are nearing completion. The results of all tests have shown the demonstration fuel elements, produced under production-line conditions, to have performed in the excellent manner expected from earlier tests of miniature fuel plates and full-sized elements. (orig.)

Final report on Thermally Modified Sand demonstration project

Energy Technology Data Exchange (ETDEWEB)

1994-09-23

The use of salt and salt/sand mixtures on icy roadway surfaces has dramatically increased during the past 30 years. Despite extensive documentation on salt related damage to the roadway improvements, vehicles and the environment, road maintenance departments have continued to rely on this practice. Road maintenance departments in northern climate areas have long recognized the safety benefits for public mobility on icy roadways from the use of sand. As an abrasive material, the sand improves the surface traction that results in more drivable and less hazardous road conditions during the winter months. Stockpiles of pure sand stored during the winter months oftentimes freeze into large unworkable, monolithic piles. To maintain a free-flowing condition, it has been found to be necessary to add salt to the sand. The addition of salt in amounts ranging from 5 to 10 percent to that of sand, is usually sufficient to provide relatively free-flowing abrasive material that could be stored in stockpiles and applied to icy road surfaces with conventional sand spreading trucks. Another alternative for winter storage of pure sand to maintain a free-flowing condition is in humidity-controlled, heated buildings. As would be expected, this method has high capital and operating costs. and not cost effective for general highway maintenance use. The invention demonstrated herein is a method of thermally modifying pure sand that will remain in a free-flowing state throughout the winter season without the need for the salt additive. The thermally modified sand provides an abrasive material that when applied to icy roads does not cause environmental and corrosive damage as done by the application of sand with salt. By employing a very simple process of freezing screened sand particles by forced air convection under subfreezing conditions, the invention creates a product that has significant value in terms of economic and environmental benefits.

Commercial incineration demonstration

International Nuclear Information System (INIS)

Vavruska, J.S.; Borduin, L.C.

1982-01-01

Low-level radioactive wastes (LLW) generated by nuclear utilities presently are shipped to commercial burial grounds for disposal. Increasing transportation and disposal costs have caused industry to consider incineration as a cost-effective means of volume reduction of combustible LLW. Repeated inquiries from the nuclear industry regarding the applicability of the Los Alamos controlled air incineration (CAI) design led the DOE to initiate a commercial demonstration program in FY-1980. Development studies and results in support of this program involving ion exchange resin incineration and fission/activation product distributions within the Los Alamos CAI are described

Radioactive waste incineration system cold demonstration test

Energy Technology Data Exchange (ETDEWEB)

Hozumi, Masahiro; Takaoku, Yoshinobu; Koyama, Shigeru; Nagae, Madoka; Seike, Yasuhiko; Yamanaka, Yasuhiro; Shibata, Kenji; Manabe, Kyoichi

1984-12-01

To demonstrate Waste Incineration System (WIS) which our company has been licensed by Combustion Engineering Inc., USA we installed a demonstration test plant in our Hiratsuka Research Laboratory and started the demonstration test on January 1984. One of the characteristics of this system is to be able to process many kinds of wastes with only one system, and to get high volume reduction factors. In our test plant, we processed paper, cloth, wood, polyethylene sheets as the samples of solid combustible wastes and spent ion exchange resins with incineration and processed condensed liquid wastes with spray drying. We have got good performances and enough Decontamination Factor (DF) data for the dust control equipment. In this paper, we introduce this demonstration test plant and report the test results up to date. (author).

Integrated test schedule for buried waste integrated demonstration

International Nuclear Information System (INIS)

Brown, J.T.; McDonald, J.K.

1992-05-01

The Integrated Test Schedule incorporates the various schedules the Buried Waste Integrated Demonstration (BWID) supports into one document. This document contains the Federal Facilities Agreement and Consent Order schedules for the Idaho National Engineering Laboratory, Hanford Reservation, Oak Ridge Reservation, and Fernald Environmental Materials Center. Included in the Integrated Test Schedule is the Buried Waste Integrated Demonstration ''windows of opportunity'' schedule. The ''windows of opportunity'' schedule shows periods of time in which Buried Waste Integrated Demonstration Program-sponsored technology demonstrations could support key decisions in the Federal Facilities Agreement and Consent Order. Schedules for the Buried Waste Integrated Demonstration-sponsored technology task plans are categorized by technology area and divided by current fiscal year and out-year. Total estimated costs for Buried Waste Integrated Demonstration-sponsored Technology Task Plans for FY-92 through FY-97 are $74.756M

Parents as Teachers Health Literacy Demonstration project: integrating an empowerment model of health literacy promotion into home-based parent education.

Science.gov (United States)

Carroll, Lauren N; Smith, Sandra A; Thomson, Nicole R

2015-03-01

The Parents as Teachers (PAT) Health Literacy Demonstration project assessed the impact of integrating data-driven reflective practices into the PAT home visitation model to promote maternal health literacy. PAT is a federally approved Maternal, Infant, Early Childhood Home Visiting program with the goal of promoting school readiness and healthy child development. This 2-year demonstration project used an open-cohort longitudinal design to promote parents' interactive and reflective skills, enhance health education, and provide direct assistance to personalize and act on information by integrating an empowerment paradigm into PAT's parent education model. Eight parent educators used the Life Skills Progression instrument to tailor the intervention to each of 103 parent-child dyads. Repeated-measures analysis of variance, paired t tests, and logistic regression combined with qualitative data demonstrated that mothers achieved overall significant improvements in health literacy, and that home visitors are important catalysts for these improvements. These findings support the use of an empowerment model of health education, skill building, and direct information support to enable parents to better manage personal and child health and health care. © 2014 Society for Public Health Education.

An ergonomics action research demonstration: integrating human factors into assembly design processes.

Science.gov (United States)

Village, J; Greig, M; Salustri, F; Zolfaghari, S; Neumann, W P

2014-01-01

In action research (AR), the researcher participates 'in' the actions in an organisation, while simultaneously reflecting 'on' the actions to promote learning for both the organisation and the researchers. This paper demonstrates a longitudinal AR collaboration with an electronics manufacturing firm where the goal was to improve the organisation's ability to integrate human factors (HF) proactively into their design processes. During the three-year collaboration, all meetings, workshops, interviews and reflections were digitally recorded and qualitatively analysed to inform new 'actions'. By the end of the collaboration, HF tools with targets and sign-off by the HF specialist were integrated into several stages of the design process, and engineers were held accountable for meeting the HF targets. We conclude that the AR approach combined with targeting multiple initiatives at different stages of the design process helped the organisation find ways to integrate HF into their processes in a sustainable way. Researchers acted as a catalyst to help integrate HF into the engineering design process in a sustainable way. This paper demonstrates how an AR approach can help achieve HF integration, the benefits of using a reflective stance and one method for reporting an AR study.

Spinstand demonstration of areal density enhancement using two-dimensional magnetic recording (invited)

Science.gov (United States)

Lippman, Thomas; Brockie, Richard; Coker, Jon; Contreras, John; Galbraith, Rick; Garzon, Samir; Hanson, Weldon; Leong, Tom; Marley, Arley; Wood, Roger; Zakai, Rehan; Zolla, Howard; Duquette, Paul; Petrizzi, Joe

2015-05-01

Exponential growth of the areal density has driven the magnetic recording industry for almost sixty years. But now areal density growth is slowing down, suggesting that current technologies are reaching their fundamental limit. The next generation of recording technologies, namely, energy-assisted writing and bit-patterned media, remains just over the horizon. Two-Dimensional Magnetic Recording (TDMR) is a promising new approach, enabling continued areal density growth with only modest changes to the heads and recording electronics. We demonstrate a first generation implementation of TDMR by using a dual-element read sensor to improve the recovery of data encoded by a conventional low-density parity-check (LDPC) channel. The signals are combined with a 2D equalizer into a single modified waveform that is decoded by a standard LDPC channel. Our detection hardware can perform simultaneous measurement of the pre- and post-combined error rate information, allowing one set of measurements to assess the absolute areal density capability of the TDMR system as well as the gain over a conventional shingled magnetic recording system with identical components. We discuss areal density measurements using this hardware and demonstrate gains exceeding five percent based on experimental dual reader components.

Spinstand demonstration of areal density enhancement using two-dimensional magnetic recording (invited)

International Nuclear Information System (INIS)

Lippman, Thomas; Brockie, Richard; Contreras, John; Garzon, Samir; Leong, Tom; Marley, Arley; Wood, Roger; Zakai, Rehan; Zolla, Howard; Coker, Jon; Galbraith, Rick; Hanson, Weldon; Duquette, Paul; Petrizzi, Joe

2015-01-01

Exponential growth of the areal density has driven the magnetic recording industry for almost sixty years. But now areal density growth is slowing down, suggesting that current technologies are reaching their fundamental limit. The next generation of recording technologies, namely, energy-assisted writing and bit-patterned media, remains just over the horizon. Two-Dimensional Magnetic Recording (TDMR) is a promising new approach, enabling continued areal density growth with only modest changes to the heads and recording electronics. We demonstrate a first generation implementation of TDMR by using a dual-element read sensor to improve the recovery of data encoded by a conventional low-density parity-check (LDPC) channel. The signals are combined with a 2D equalizer into a single modified waveform that is decoded by a standard LDPC channel. Our detection hardware can perform simultaneous measurement of the pre- and post-combined error rate information, allowing one set of measurements to assess the absolute areal density capability of the TDMR system as well as the gain over a conventional shingled magnetic recording system with identical components. We discuss areal density measurements using this hardware and demonstrate gains exceeding five percent based on experimental dual reader components

Spinstand demonstration of areal density enhancement using two-dimensional magnetic recording (invited)

Energy Technology Data Exchange (ETDEWEB)

Lippman, Thomas, E-mail: Thomas.Lippman@hgst.com; Brockie, Richard; Contreras, John; Garzon, Samir; Leong, Tom; Marley, Arley; Wood, Roger; Zakai, Rehan; Zolla, Howard [HGST, a Western Digital Company, San Jose, California 95119 (United States); Coker, Jon; Galbraith, Rick; Hanson, Weldon [HGST, a Western Digital Company, Rochester, Minnesota 55901 (United States); Duquette, Paul; Petrizzi, Joe [Avago Technologies, San Jose, California 95131 (United States)

2015-05-07

Exponential growth of the areal density has driven the magnetic recording industry for almost sixty years. But now areal density growth is slowing down, suggesting that current technologies are reaching their fundamental limit. The next generation of recording technologies, namely, energy-assisted writing and bit-patterned media, remains just over the horizon. Two-Dimensional Magnetic Recording (TDMR) is a promising new approach, enabling continued areal density growth with only modest changes to the heads and recording electronics. We demonstrate a first generation implementation of TDMR by using a dual-element read sensor to improve the recovery of data encoded by a conventional low-density parity-check (LDPC) channel. The signals are combined with a 2D equalizer into a single modified waveform that is decoded by a standard LDPC channel. Our detection hardware can perform simultaneous measurement of the pre- and post-combined error rate information, allowing one set of measurements to assess the absolute areal density capability of the TDMR system as well as the gain over a conventional shingled magnetic recording system with identical components. We discuss areal density measurements using this hardware and demonstrate gains exceeding five percent based on experimental dual reader components.

Field demonstration of foam injection to confine a chlorinated solvent source zone.

Science.gov (United States)

Portois, Clément; Essouayed, Elyess; Annable, Michael D; Guiserix, Nathalie; Joubert, Antoine; Atteia, Olivier

2018-05-01

A novel approach using foam to manage hazardous waste was successfully demonstrated under active site conditions. The purpose of the foam was to divert groundwater flow, that would normally enter the source zone area, to reduce dissolved contaminant release to the aquifer. During the demonstration, foam was pre generated and directly injected surrounding the chlorinated solvent source zone. Despite the constraints related to the industrial activities and non-optimal position of the injection points, the applicability and effectiveness of the approach have been highlighted using multiple metrics. A combination of measurements and modelling allowed definition of the foam extent surrounding each injection point, and this appears to be the critical metric to define the success of the foam injection approach. Information on the transport of chlorinated solvents in groundwater showed a decrease of contaminant flux by a factor of 4.4 downstream of the confined area. The effective permeability reduction was maintained over a period of three months. The successful containment provides evidence for consideration of the use of foam to improve traditional flushing techniques, by increasing the targeting of contaminants by remedial agents. Copyright © 2018 Elsevier B.V. All rights reserved.

CT Demonstration of Caput Medusae

Science.gov (United States)

Weber, Edward C.; Vilensky, Joel A.

2009-01-01

Maximum intensity and volume rendered CT displays of caput medusae are provided to demonstrate both the anatomy and physiology of this portosystemic shunt associated with portal hypertension. (Contains 2 figures.)

GATEWAY Demonstrations: Trial Demonstration of Area Lighting Retrofit, Yuma Border Patrol, Yuma, Arizona

Energy Technology Data Exchange (ETDEWEB)

Wilkerson, A. M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); McCullough, J. J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2014-12-31

Along the Yuma Sector Border Patrol Area in Yuma, Arizona, the GATEWAY program conducted a trial demonstration in which the incumbent quartz metal halide area lighting was replaced with LED at three pole locations at the Yuma Sector Border Patrol Area in Yuma, Arizona. The retrofit was documented to better understand LED technology performance in high-temperature environments.

Subsurface barrier demonstration test strategy and performance specification

International Nuclear Information System (INIS)

Treat, R.L.; Cruse, J.M.

1994-05-01

This document was developed to help specify a major demonstration test project of subsurface barrier systems supporting the Tank Waste Remediation System (TWRS) Program. The document focuses discussion on requirements applicable to demonstration of three subsurface barrier concepts: (1) Injected Material, (2) Cryogenic, and (3) Desiccant. Detailed requirements are provided for initial qualification of a technology proposal followed by the pre-demonstration and demonstration test requirements and specifications. Each requirement and specification is accompanied by a discussion of the rationale for it. The document also includes information on the Hanford Site tank farms and related data; the related and currently active technology development projects within the DOE's EM-50 Program; and the overall demonstration test strategy. Procurement activities and other preparations for actual demonstration testing are on hold until a decision is made regarding further development of subsurface barriers. Accordingly, this document is being issued for information only

Portal imaging improvement with a low energy un flattened beam in high energy medical accelerators

Energy Technology Data Exchange (ETDEWEB)

Krutman, Y; Faermann, S; Tsechanski, A [Ben-Gurion Univ. of the Negev, Beersheba (Israel)

1996-12-01

In this work we present a further improvement of the portal film option, for a Clinac 18 accelerator with a 10 MV therapeutic x-ray beam. This is done by lowering the nominal photon energy to 4 MV, therefore increasing the relative contribution of the low energy portion of the x-ray spectrum. Improvement of the image quality is demonstrated with a portal film scale tray, and with an anthropomorphic phantom, a graphical analysis demonstrates the improvement on image (authors).

Demonstrator study for micro-ranging-laser device

Science.gov (United States)

Henkel, Hartmut; Bernhardt, Bodo; Pereira do Carmo, J.

2017-11-01

Within ESA's Innovation Triangle Initiative (ITI) a demonstrator breadboard for a micro-ranging-laser device "MYLRAD" has been developed. Its working principle is the measurement of the round-trip delay time of a laser beam as a phase shift. The demonstrator consists of the laser diode (30 mW, square wave AM), optics, APD detector, narrowband preamplifier, limiter, and a phase digitiser based on a novel noise-shaping synchroniser (NSS) circuit; this works without ADCs and can be built from rad-hard components for space. The system timing and the digitiser algorithm are performed by an FPGA. The demonstrator has been tested at ranges from 1 m to 30 m. With a static non-cooperative target an RMS noise of 1 mm at a result rate of 60 Hz was reached. The demonstrator needs less than 2.5 W power.

Large-Scale Demonstration of Liquid Hydrogen Storage with Zero Boiloff for In-Space Applications

Science.gov (United States)

Hastings, L. J.; Bryant, C. B.; Flachbart, R. H.; Holt, K. A.; Johnson, E.; Hedayat, A.; Hipp, B.; Plachta, D. W.

2010-01-01

Cryocooler and passive insulation technology advances have substantially improved prospects for zero-boiloff cryogenic storage. Therefore, a cooperative effort by NASA s Ames Research Center, Glenn Research Center, and Marshall Space Flight Center (MSFC) was implemented to develop zero-boiloff concepts for in-space cryogenic storage. Described herein is one program element - a large-scale, zero-boiloff demonstration using the MSFC multipurpose hydrogen test bed (MHTB). A commercial cryocooler was interfaced with an existing MHTB spray bar mixer and insulation system in a manner that enabled a balance between incoming and extracted thermal energy.

Catalytic hydrotreatment of refinery waste: Demonstration project

Energy Technology Data Exchange (ETDEWEB)

1989-01-01

The object of this project and report is to produce liquid hydrocarbons by the catalytic hydroprocessing of solid refinery wastes (hard pitches) in order to improve the profitability of deep conversion processes and reduce the excess production of heavy fuels. The project was mostly carried out on the ASVAHL demonstration platform site, at Solaize, and hard pitches were produced primarily by deasphalting of atmospheric or vacuum distillation residues. The project includes two experimental phases and an economic evaluation study phase. In Phase 1, two granular catalysts were used to transform pitch into standard low sulfur fuel oil: a continuously moving bed, with demetallation and conversion catalyst; a fixed bed, with hydrorefining catalyst. In Phase 2 of the project, it was proven that a hydrotreatment process using a finely dispersed catalyst in the feedstock, can, under realistic operating conditions, transform with good yields hard pitch into distillates that can be refined through standard methods. In Phase 3 of the project, it was shown that the economics of such processes are tightly linked to the price differential between white'' and black'' oil products, which is expected to increase in the future. Furthermore, the evolution of environmental constraints will impel the use of such methods, thus avoiding the coproduction of polluting solid residues. 11 figs., 1 tab.

Demonstrating diamond wire cutting of the TFTR

International Nuclear Information System (INIS)

Rule, K.; Perry, E.; Larson, S.; Viola, M.

2000-01-01

The Tokamak Fusion Test Reactor (TFTR) ceased operation in April 1997 and decommissioning commenced in October 1999. The deuterium-tritium fusion experiments resulted in contaminating the vacuum vessel with tritium and activating the materials with 14 Mev neutrons. The total tritium content within the vessel is in excess of 7,000 Curies while dose rates approach 50 mRem/hr. These radiological hazards along with the size of the Tokamak (100 cubic meters) present a unique and challenging task for dismantling. Plasma arc cutting is the current baseline technology for the dismantlement of fission reactors. This technology is typically used because of its faster cutting times. Alternatively, an innovative approach for dismantlement of the TFTR is the use of diamond wire cutting technology. Recent improvements in diamond wire technology have allowed the cutting of carbon steel components such as pipe, plate, and tube bundles in heat exchangers. Some expected benefits of this technology include: significantly reduction in airborne contaminates, reduced personnel exposure, a reduced risk of spread of tritium contamination, and reduced overall costs as compared to using plasma arc cutting. This paper will provide detailed results of the diamond wire cutting demonstration that was completed in September of 1999, on a mock-up of this complex reactor. The results will identify cost, safety, industrial and engineering parameters, and the related performance of each situation

Demonstrating diamond wire cutting of the TFTR

Energy Technology Data Exchange (ETDEWEB)

Rule, K.; Perry, E.; Larson, S.; Viola, M. [and others

2000-02-24

The Tokamak Fusion Test Reactor (TFTR) ceased operation in April 1997 and decommissioning commenced in October 1999. The deuterium-tritium fusion experiments resulted in contaminating the vacuum vessel with tritium and activating the materials with 14 Mev neutrons. The total tritium content within the vessel is in excess of 7,000 Curies while dose rates approach 50 mRem/hr. These radiological hazards along with the size of the Tokamak (100 cubic meters) present a unique and challenging task for dismantling. Plasma arc cutting is the current baseline technology for the dismantlement of fission reactors. This technology is typically used because of its faster cutting times. Alternatively, an innovative approach for dismantlement of the TFTR is the use of diamond wire cutting technology. Recent improvements in diamond wire technology have allowed the cutting of carbon steel components such as pipe, plate, and tube bundles in heat exchangers. Some expected benefits of this technology include: significantly reduction in airborne contaminates, reduced personnel exposure, a reduced risk of spread of tritium contamination, and reduced overall costs as compared to using plasma arc cutting. This paper will provide detailed results of the diamond wire cutting demonstration that was completed in September of 1999, on a mock-up of this complex reactor. The results will identify cost, safety, industrial and engineering parameters, and the related performance of each situation.

Transportable Vitrification System Demonstration on Mixed Waste

International Nuclear Information System (INIS)

Zamecnik, J.R.; Whitehouse, J.C.; Wilson, C.N.; Van Ryn, F.R.

1998-01-01

This paper describes preliminary results from the first demonstration of the Transportable Vitrification System (TVS) on actual mixed waste. The TVS is a fully integrated, transportable system for the treatment of mixed and low-level radioactive wastes. The demonstration was conducted at Oak Ridge's East Tennessee Technology Park (ETTP), formerly known as the K-25 site. The purpose of the demonstration was to show that mixed wastes could be vitrified safely on a 'field' scale using joule-heated melter technology and obtain information on system performance, waste form durability, air emissions, and costs

Prototypical consolidation demonstration project - Final fuel recommendation report

International Nuclear Information System (INIS)

Piscitella, R.R.; Paskey, W.R.

1987-01-01

The Prototypical Consolidation Demonstration (PCD) Project will, in its final phase, conduct a demonstration of the equipment's ability to consolidate actual spent commercial fuel. Since budget and schedule limitations do not allow this demonstration to include all types of fuel assemblies, a selection process was utilized to identify the fuel types that would represent predominate fuel inventories and that would demonstrate the equipment's abilities. The Pressurized Water Reactor (PWR) fuel assemblies that were suggested for use in the PCD Project Hot Demonstration were Babcock and Wilcox (B and W) 15 x 15's, and Westinghouse (WE) 15 x 15's. The Boiling Water Reactor (BWR) fuel suggested was the General Electric (GE) 8 x 8

RCRA permit modifications and the functional equivalency demonstration: A case study

International Nuclear Information System (INIS)

Kinker, J.; Lyon, W.; Carnes, R.; Loehr, C.; Elsberry, K.; Garcia, P.

1996-01-01

Hazardous waste operating permits issued under the Resource Conservation and Recovery Act (RCRA) often impose requirements, typically by reference to the original permit application, that specific components and equipment be used. Consequently, changing these items, even for the purpose of routine maintenance, may first require that the owner/operator request a potentially time-consuming and costly permit modification. However, the owner/operator may demonstrate that a modification is not required because the planned changes are functionally equivalent, as defined by RCRA, to the original specifications embodied by the permit. The Controlled-Air Incinerator at Los Alamos National Laboratory is scheduled for maintenance and improvements that involve replacement of components. The incinerator's carbon adsorption unit/high efficiency particulate air filtration system, in particular, was redesigned to improve reliability and minimize maintenance. A study was performed to determine whether the redesigned unit would qualify as functionally equivalent to the original component. in performing this study, the following steps were taken: (a) the key performance factors were identified; (b) performance data describing the existing unit were obtained; (c) performance of both the existing and redesigned units was simulated; and (d) the performance data were compared to ascertain whether the components could qualify as functionally equivalent

Demonstration of hetero-gate-dielectric tunneling field-effect transistors (HG TFETs).

Science.gov (United States)

Choi, Woo Young; Lee, Hyun Kook

2016-01-01

The steady scaling-down of semiconductor device for improving performance has been the most important issue among researchers. Recently, as low-power consumption becomes one of the most important requirements, there have been many researches about novel devices for low-power consumption. Though scaling supply voltage is the most effective way for low-power consumption, performance degradation is occurred for metal-oxide-semiconductor field-effect transistors (MOSFETs) when supply voltage is reduced because subthreshold swing (SS) of MOSFETs cannot be lower than 60 mV/dec. Thus, in this thesis, hetero-gate-dielectric tunneling field-effect transistors (HG TFETs) are investigated as one of the most promising alternatives to MOSFETs. By replacing source-side gate insulator with a high- k material, HG TFETs show higher on-current, suppressed ambipolar current and lower SS than conventional TFETs. Device design optimization through simulation was performed and fabrication based on simulation demonstrated that performance of HG TFETs were better than that of conventional TFETs. Especially, enlargement of gate insulator thickness while etching gate insulator at the source side was improved by introducing HF vapor etch process. In addition, the proposed HG TFETs showed higher performance than our previous results by changing structure of sidewall spacer by high- k etching process.

Poor Demonstration and Knowledge of AED Electrode Placement by Certified and Experienced BLS/AED Instructors

DEFF Research Database (Denmark)

Stærk, Mathilde; Vammen, Lauge; Hansen, Camilla

2017-01-01

to demonstrate correct use of an AED remains to be investigated.Aim: To determine BLS instructors’ competence in using an AED.Methods: Certified BLS instructors were asked to operate a training AED (Lifepak ® CR-T Plus, PhysioControl, default audiotape duration of 67 sec from start to time of shock......Introduction: Use of an automated external defibrillator (AED) improves survival. Incorrect AED electrode placement may affect defibrillation success and survival. During courses in basic life support (BLS), instructors teach laypeople how to use an AED. However, BLS instructors’ ability......) on a resuscitation manikin with arms (AMBU ® Man, AMBU) as they would do in a teaching situation but without any explanations. The demonstration by the instructor was video recorded. After shock delivery the AED electrode position was assessed i.e. the distance from the center of the electrode to the recommended...

Background Model for the Majorana Demonstrator

Science.gov (United States)

Cuesta, C.; Abgrall, N.; Aguayo, E.; Avignone, F. T.; Barabash, A. S.; Bertrand, F. E.; Boswell, M.; Brudanin, V.; Busch, M.; Byram, D.; Caldwell, A. S.; Chan, Y.-D.; Christofferson, C. D.; Combs, D. C.; Detwiler, J. A.; Doe, P. J.; Efremenko, Yu.; Egorov, V.; Ejiri, H.; Elliott, S. R.; Fast, J. E.; Finnerty, P.; Fraenkle, F. M.; Galindo-Uribarri, A.; Giovanetti, G. K.; Goett, J.; Green, M. P.; Gruszko, J.; Guiseppe, V. E.; Gusev, K.; Hallin, A. L.; Hazama, R.; Hegai, A.; Henning, R.; Hoppe, E. W.; Howard, S.; Howe, M. A.; Keeter, K. J.; Kidd, M. F.; Kochetov, O.; Konovalov, S. I.; Kouzes, R. T.; LaFerriere, B. D.; Leon, J.; Leviner, L. E.; Loach, J. C.; MacMullin, J.; MacMullin, S.; Martin, R. D.; Meijer, S.; Mertens, S.; Nomachi, M.; Orrell, J. L.; O'Shaughnessy, C.; Overman, N. R.; Phillips, D. G.; Poon, A. W. P.; Pushkin, K.; Radford, D. C.; Rager, J.; Rielage, K.; Robertson, R. G. H.; Romero-Romero, E.; Ronquest, M. C.; Schubert, A. G.; Shanks, B.; Shima, T.; Shirchenko, M.; Snavely, K. J.; Snyder, N.; Suriano, A. M.; Thompson, J.; Timkin, V.; Tornow, W.; Trimble, J. E.; Varner, R. L.; Vasilyev, S.; Vetter, K.; Vorren, K.; White, B. R.; Wilkerson, J. F.; Wiseman, C.; Xu, W.; Yakushev, E.; Young, A. R.; Yu, C.-H.; Yumatov, V.

The Majorana Collaboration is constructing a system containing 40 kg of HPGe detectors to demonstrate the feasibility and potential of a future tonne-scale experiment capable of probing the neutrino mass scale in the inverted-hierarchy region. To realize this, a major goal of the Majorana Demonstrator is to demonstrate a path forward to achieving a background rate at or below 1 cnt/(ROI-t-y) in the 4 keV region of interest around the Q-value at 2039 keV. This goal is pursued through a combination of a significant reduction of radioactive impurities in construction materials with analytical methods for background rejection, for example using powerful pulse shape analysis techniques profiting from the p-type point contact HPGe detectors technology. The effectiveness of these methods is assessed using simulations of the different background components whose purity levels are constrained from radioassay measurements.

School nurses' role in asthma management, school absenteeism, and cost savings: a demonstration project.

Science.gov (United States)

Rodriguez, Eunice; Rivera, Diana Austria; Perlroth, Daniella; Becker, Edmund; Wang, Nancy Ewen; Landau, Melinda

2013-12-01

With increasing budget cuts to education and social services, rigorous evaluation needs to document school nurses' impact on student health, academic outcomes, and district funding. Utilizing a quasi-experimental design, we evaluated outcomes in 4 schools with added full-time nurses and 5 matched schools with part-time nurses in the San Jose Unified School District. Student data and logistic regression models were used to examine predictors of illness-related absenteeism for 2006-2007 and 2008-2009. We calculated average daily attendance (ADA) funding and parent wages associated with an improvement in illness-related absenteeism. Utilizing parent surveys, we also estimated the cost of services for asthma-related visits to the emergency room (ER; N = 2489). Children with asthma were more likely to be absent due to illness; however, mean absenteeism due to illness decreased when full-time nurses were added to demonstration schools but increased in comparison schools during 2008-2009, resulting in a potential savings of $48,518.62 in ADA funding (N = 6081). Parents in demonstration schools reported fewer ER visits, and the estimated savings in ER services and parent wages were significant. Full-time school nurses play an important role in improving asthma management among students in underserved schools, which can impact school absenteeism and attendance-related economic costs. © 2013, American School Health Association.

National Quality Improvement Center on Early Childhood

Science.gov (United States)

Browne, Charlyn Harper

2014-01-01

The national Quality Improvement Center on early Childhood (QIC-eC) funded four research and demonstration projects that tested child maltreatment prevention approaches. The projects were guided by several key perspectives: the importance of increasing protective factors in addition to decreasing risk factors in child maltreatment prevention…

Demonstration of a 1 MWe biomass power plant at USMC Base Camp Lejeune

International Nuclear Information System (INIS)

Cleland, J.; Purvis, C.R.

1997-01-01

A biomass energy conversion project is being sponsored by the U.S. Environmental Protection Agency (EPA) to demonstrate an environmentally and economically sound electrical power option for government installations, industrial sites, rural cooperatives, small municipalities, and developing countries. Under a cooperative agreement with EPA, Research Triangle Institute is initiating operation of the Camp Lejeune Energy from Wood (CLEW) biomass plant. Wood gasification combined with internal combustion engines was chosen because of (1) recent improvements in gas cleaning, (2) simple, economical operation for units less than 10 MW, and (3) the option of a clean, cheap fuel for the many existing facilities generating expensive electricity from petroleum fuels with reciprocating engines. The plant incorporates a downdraft, moving bed gasifier utilizing hogged waste wood from the Marine Corps Base at Camp Lejeune, NC. A moving bed bulk wood dryer and both spark ignition and diesel engines are included. Unique process design features are briefly described relative to the gasifier, wood drying, tar separation, and process control. A test plan for process optimization and demonstration of reliability, economics, and environmental impact is outlined. (author)

Mixed Waste Landfill Integrated Demonstration

International Nuclear Information System (INIS)

1994-02-01

The mission of the Mixed Waste Landfill Integrated Demonstration (MWLID) is to demonstrate, in contaminated sites, new technologies for clean-up of chemical and mixed waste landfills that are representative of many sites throughout the DOE Complex and the nation. When implemented, these new technologies promise to characterize and remediate the contaminated landfill sites across the country that resulted from past waste disposal practices. Characterization and remediation technologies are aimed at making clean-up less expensive, safer, and more effective than current techniques. This will be done by emphasizing in-situ technologies. Most important, MWLID's success will be shared with other Federal, state, and local governments, and private companies that face the important task of waste site remediation. MWLID will demonstrate technologies at two existing landfills. Sandia National Laboratories' Chemical Waste Landfill received hazardous (chemical) waste from the Laboratory from 1962 to 1985, and the Mixed-Waste Landfill received hazardous and radioactive wastes (mixed wastes) over a twenty-nine year period (1959-1988) from various Sandia nuclear research programs. Both landfills are now closed. Originally, however, the sites were selected because of Albuquerque's and climate and the thick layer of alluvial deposits that overlay groundwater approximately 480 feet below the landfills. This thick layer of ''dry'' soils, gravel, and clays promised to be a natural barrier between the landfills and groundwater

Demonstration of HITEX

International Nuclear Information System (INIS)

Morrison, H.D.; Woodall, K.B.

1993-01-01

A model reactor for HITEX successfully demonstrated the concept of high-temperature isotopic exchange in a closed loop simulating the conditions for fusion fuel cleanup. The catalyst of platinum on alumina pellets provided a surface area large enough to operate the reactor at 400 degrees celsius with flow rates up to 2 L/min. A 15-L tank containing a mixture of 4% CD 4 in H 2 was depleted in deuterium within 75 minutes down to 100 ppm HD above the natural concentration of HD in the make-up hydrogen stream. The application to tritium removal from tritiated impurities in a hydrogen stream will work as well or better

Test plan for the retrieval demonstration

International Nuclear Information System (INIS)

Valentich, D.J.

1993-05-01

This test plan describes a simulated buried waste retrieval demonstration that will be performed at the Caterpillar, Inc., Edwards Training Center located near Peoria, Illinois. The purpose of the demonstration is to determine the effectiveness of using readily available excavation equipment to retrieve, size, and handle various simulated waste forms that are similar in size, structure, and composition to those expected to be found in US Department of Energy contaminated waste pits and trenches. The objectives of this demonstration are to: meet and maintain daily production goals of 80 yd 3 /day; minimize spillage and dust generation through careful and deliberate operations; document and evaluate methods for manipulating, sizing, and/or working around large objects; and document and evaluate requirements for operator augmentation and remote operation for hot test pit excavation operations. Four conditions comprising the range of environments to be evaluated include excavation of random material from below grade; stacked boxes and barrels from below grade; random materials from at grade; and stacked boxes and barrels from at grade. Results of the retrieval demonstration will reduce unknowns in the body of knowledge about retrieval equipment and procedural options for removal of buried transuranic (TRU) waste at the Idaho National Engineering Laboratory. It is anticipated that DOE will factor this information into a remedial investigation/feasibility plan leading to a final record of decision for disposition of buried TRU waste

OVERVIEW OF USEPA'S ARSENIC TECHNOLOGY DEMONSTRATION PROGRAM

Science.gov (United States)

This presentation provides a summary on the Arsenic Treatment Technology Demonstration Program. The information includes the history and the current status of the demonstration projects on both round 1 and round 2 including some photos of the treatment systems. The presentation m...

DEMONSTRATION OF SORBENT INJECTION TECHNOLOGY ON A WALL-FIRED UTILITY BOILER (EDGEWATER LIMB DEMONSTRATION)

Science.gov (United States)

The report gives results of the full-scale demonstration of Limestone Injection Multistage Burner (LIMB) technology on the coal-fired, 105 MW, Unit 4 boiler at Ohio Edison's Edgewater Station. eveloped as a technology aimed at moderate levels of sulfur dioxide (SO2) and nitrogen ...

Improving breast cancer outcome by preoperative systemic therapy and image-guided surgery

NARCIS (Netherlands)

Mieog, Jan Sven David

2011-01-01

This thesis consists of two parts. In part I, we have demonstrated that preoperatively administrated systemic (neoadjuvant) therapy is a feasible treatment strategy in early stage breast cancer to achieve improved surgical options and to assess tumor response. We also demonstrated that

Duodenal diverticula demonstrated by barium examination

Energy Technology Data Exchange (ETDEWEB)

Christiansen, T.; Thommesen, P.

An investigation for biliary tract calculi and food-stimulated gastro-oesophageal reflux was carried out in 37 patients with duodenal diverticula demonstrated by barium examination. Sixty per cent of the diverticula were located in the descending part of the duodenum. Biliary tract calculi were demonstrated in 38 per cent and food-stimulated gastro-oesophageal reflux in 81 per cent of the patients. The detection of a duodenal diverticulum should result in a supplementary investigation for gallstones and gastrooesophageal reflux and its sequelae.

Space Internet-Embedded Web Technologies Demonstration

Science.gov (United States)

Foltz, David A.

2001-01-01

The NASA Glenn Research Center recently demonstrated the ability to securely command and control space-based assets by using the Internet and standard Internet Protocols (IP). This is a significant accomplishment because future NASA missions will benefit by using Internet standards-based protocols. The benefits include reduced mission costs and increased mission efficiency. The Internet-Based Space Command and Control System Architecture demonstrated at the NASA Inspection 2000 event proved that this communications architecture is viable for future NASA missions.

Experimental demonstration of the transmission performance for LDPC-coded multiband OFDM ultra-wideband over fiber system

Science.gov (United States)

He, Jing; Wen, Xuejie; Chen, Ming; Chen, Lin; Su, Jinshu

2015-01-01

To improve the transmission performance of multiband orthogonal frequency division multiplexing (MB-OFDM) ultra-wideband (UWB) over optical fiber, a pre-coding scheme based on low-density parity-check (LDPC) is adopted and experimentally demonstrated in the intensity-modulation and direct-detection MB-OFDM UWB over fiber system. Meanwhile, a symbol synchronization and pilot-aided channel estimation scheme is implemented on the receiver of the MB-OFDM UWB over fiber system. The experimental results show that the LDPC pre-coding scheme can work effectively in the MB-OFDM UWB over fiber system. After 70 km standard single-mode fiber (SSMF) transmission, at the bit error rate of 1 × 10-3, the receiver sensitivities are improved about 4 dB when the LDPC code rate is 75%.

Out-of-tank evaporator demonstration. Final report

International Nuclear Information System (INIS)

Lucero, A.J.; Jennings, H.L.; VanEssen, D.C.

1998-02-01

The project reported here was conducted to demonstrate a skid-mounted, subatmospheric evaporator to concentrate liquid low-level waste (LLLW) stored in underground tanks at Oak Ridge National Laboratory (ORNL). This waste is similar to wastes stored at Hanford and Savannah River. A single-stage subatmospheric evaporator rated to produce 90 gallons of distillate per hour was procured from Delta Thermal, Inc., of Pensacola, Florida, and installed in an existing building. During the 8-day demonstration, 22,000 gal of LLLW was concentrated by 25% with the evaporator system. Decontamination factors achieved averaged 5 x 10 6 (i.e., the distillate contained five million times less Cesium 137 than the feed). Evaporator performance substantially exceeded design requirements and expectations based on bench-scale surrogate test data. Out-of tank evaporator demonstration operations successfully addressed the feasibility of hands-on maintenance. Demonstration activities indicate that: (1) skid-mounted, mobile equipment is a viable alternative for the treatment of ORNL LLLW, and (2) hands-on maintenance and decontamination for movement to another site is achievable. Cost analysis show that 10% of the demonstration costs will be immediately recovered by elimination of solidification and disposal costs. The entire cost of the demonstration can be recovered by processing the inventory of Melton Valley Storage Tank waste and/or sluice water prior to solidifications. An additional savings of approximately $200,000 per year can be obtained by processing newly generated waste through the system. The results indicate that this type of evaporator system should be considered for application across the DOE complex. 25 refs., 11 figs., 2 tabs

A Management Tool for Improvement (Improving) IMS Stations Performance

International Nuclear Information System (INIS)

Mohammad, D.; Pantin, A.; Quintana, E.

2011-01-01

IMS-Maintenance is a software under development by the personnel of ARN-CTBT office, intended for the technical management of IMS stations under ARN's responsibility. This software integrates the whole control of the equipment in an IMS station, including the management of consumables used in daily or periodic operation. It permits an easy retrieval (access) of the technical features, suppliers, etc. of each item of the equipment, as well as its maintenance history and scheduled task. Although this project is still in a starting phase, a preliminary version of this software is being used in radionuclide station RN01 (Buenos Aires), having already demonstrated its usefulness and potential for the improvement of IMS station management. (authors)

Incineration demonstration at Savannah River

International Nuclear Information System (INIS)

Lewandowski, K.E.; Becker, G.W.; Mersman, K.E.; Roberson, W.A.

1983-01-01

A full-scale incineration process for Savannah River Plant (SRP) low level beta-gamma combustible waste was demonstrated at the Savannah River Laboratory (SRL) using nonradioactive wastes. From October 1981 through September 1982, 15,700 kilograms of solid waste and 5.7 m 3 of solvent were incinerated. Emissions of off-gas components (NO/sub x/, SO 2 , CO, and particulates) were well below South Carolina state standards. Volume reductions of 20:1 for solid waste and 7:1 for Purex solvent/lime slurry were achieved. Presently, the process is being upgraded by SRP to accept radioactive wastes. During a two-year SRP demonstration, the facility will be used to incinerate slightly radioactive ( 3 ) solvent and suspect level (<1 mR/hr at 0.0254 meter) solid wastes

HYDROGEN ENERGY: TERCEIRA ISLAND DEMONSTRATION FACILITY

Directory of Open Access Journals (Sweden)

MARIO ALVES

2008-07-01

Full Text Available The present paper gives a general perspective of the efforts going on at Terceira Island in Azores, Portugal, concerning the implementation of an Hydrogen Economy demonstration campus. The major motivation for such a geographical location choice was the abundance of renewable resources like wind, sea waves and geothermal enthalpy, which are of fundamental importance for the demonstration of renewable hydrogen economy sustainability. Three main campus will be implemented: one at Cume Hill, where the majority of renewable hydrogen production will take place using the wind as the primary energy source, a second one at Angra do Heroismo Industrial park, where a cogen electrical – heat power station will be installed, mainly to feed a Municipal Solid Waste processing plant and a third one, the Praia da Vitoria Hydrogenopolis, where several final consumer demonstrators will be installed both for public awareness and intensive study of economic sustainability and optimization. Some of these units are already under construction, particularly the renewable hydrogen generation facilities.

Staunton 1 reclamation demonstration project. Aquatic ecosystems. Final report

Energy Technology Data Exchange (ETDEWEB)

Vinikour, W. S.

1981-02-01

To provide long-term indications of the potential water quality improvements following reclamation efforts at the Staunton 1 Reclamation Demonstration Project, macroinvertebrates were collected from three on-site ponds and from the receiving stream (Cahokia Creek) for site drainage. Implications for potential benthic community differences resulting from site runoff were disclosed, but macroinvertebrate diversity throughout Cahokia Creek was limited due to an unstable, sandy substrate. The three ponds sampled were the New Pond, which was created as part of the reclamation activities; the Shed Pond, which and the Old Pond, which, because it was an existing, nonimpacted pond free of site runoff, served as a control. Comparisons of macroinvertebrates from the ponds indicated the potential for the New Pond to develop into a productive ecosystem. Macroinvertebrates in the New Pond were generally species more tolerant of acid mine drainage conditions. However, due to the present limited faunal densities and the undesirable physical and chemical characteristics of the New Pond, the pond should not be stocked with fish at this time.

Marketing Plan for Demonstration and Validation Assets

Energy Technology Data Exchange (ETDEWEB)

None, None

2008-05-30

The National Security Preparedness Project (NSPP), is to be sustained by various programs, including technology demonstration and evaluation (DEMVAL). This project assists companies in developing technologies under the National Security Technology Incubator program (NSTI) through demonstration and validation of technologies applicable to national security created by incubators and other sources. The NSPP also will support the creation of an integrated demonstration and validation environment. This report documents the DEMVAL marketing and visibility plan, which will focus on collecting information about, and expanding the visibility of, DEMVAL assets serving businesses with national security technology applications in southern New Mexico.

A turtle cognition research demonstration enhances visitor engagement and keeper-animal relationships.

Science.gov (United States)

Alba, Andrew C; Leighty, Katherine A; Pittman Courte, Victoria L; Grand, Alison P; Bettinger, Tamara L

2017-07-01

Environmental enrichment techniques present animals with cognitive challenges while providing them opportunities to make choices and exert control over their environment. In this way, cognitive research and training is enriching to animals and can be used as a form of enrichment in zoos and aquariums. Cognitive research demonstrations also provide an opportunity to enhance visitor experience, as well as foster interactions between animals and keepers. We investigated how cognitive research sessions involving eastern box turtles (Terrapene carolina carolina) at Disney's Animal Kingdom ® impacted both the rate of visitors coming to the exhibit and the amount of time they spent engaged. Further, we used a questionnaire to assess the impact of keeper participation in these sessions on their relationships with and perceptions of the turtles. While visitation rate to the exhibit was not impacted, cognitive research sessions held visitor attention for longer than keeper interpretation or at times during which no keepers or researchers were present. We also found that keepers that had worked with the turtles for longer and keepers that regularly participated in cognitive research sessions reported stronger bonds with the turtles. Our research suggests that use of cognitive research and training demonstrations for guest viewing in zoos and aquariums may enhance visitor learning opportunities by increasing the amount of time they spend at the exhibit. Our study also provides evidence that participation in such demonstrations by zoo and aquarium professionals can be related to improved keeper-animal bonds, potentially resulting in better husbandry and enhanced animal welfare. © 2017 Wiley Periodicals, Inc.

An improved behavioural assay demonstrates that ultrasound vocalizations constitute a reliable indicator of chronic cancer pain and neuropathic pain

Directory of Open Access Journals (Sweden)

Selvaraj Deepitha

2010-03-01

Full Text Available Abstract Background On-going pain is one of the most debilitating symptoms associated with a variety of chronic pain disorders. An understanding of mechanisms underlying on-going pain, i.e. stimulus-independent pain has been hampered so far by a lack of behavioural parameters which enable studying it in experimental animals. Ultrasound vocalizations (USVs have been proposed to correlate with pain evoked by an acute activation of nociceptors. However, literature on the utility of USVs as an indicator of chronic pain is very controversial. A majority of these inconsistencies arise from parameters confounding behavioural experiments, which include novelty, fear and stress due to restrain, amongst others. Results We have developed an improved assay which overcomes these confounding factors and enables studying USVs in freely moving mice repetitively over several weeks. Using this improved assay, we report here that USVs increase significantly in mice with bone metastases-induced cancer pain or neuropathic pain for several weeks, in comparison to sham-treated mice. Importantly, analgesic drugs which are known to alleviate tumour pain or neuropathic pain in human patients significantly reduce USVs as well as mechanical allodynia in corresponding mouse models. Conclusions We show that studying USVs and mechanical allodynia in the same cohort of mice enables comparing the temporal progression of on-going pain (i.e. stimulus-independent pain and stimulus-evoked pain in these clinically highly-relevant forms of chronic pain.

Super resolution PLIF demonstrated in turbulent jet flows seeded with I2

Science.gov (United States)

Xu, Wenjiang; Liu, Ning; Ma, Lin

2018-05-01

Planar laser induced fluorescence (PLIF) represents an indispensable tool for flow and flame imaging. However, the PLIF technique suffers from limited spatial resolution or blurring in many situations, which restricts its applicability and capability. This work describes a new method, named SR-PLIF (super-resolution PLIF), to overcome these limitations and enhance the capability of PLIF. The method uses PLIF images captured simultaneously from two (or more) orientations to reconstruct a final PLIF image with resolution enhanced or blurring removed. This paper reports the development of the reconstruction algorithm, and the experimental demonstration of the SR-PLIF method both with controlled samples and with turbulent flows seeded with iodine vapor. Using controlled samples with two cameras, the spatial resolution in the best case was improved from 0.06 mm in the projections to 0.03 mm in the SR image, in terms of the spreading width of a sharp edge. With turbulent flows, an image sharpness measure was developed to quantify the spatial resolution, and SR reconstruction with two cameras can effectively improve the spatial resolution compared to the projections in terms of the sharpness measure.

An improved plating assay for determination of phage titer | Yang ...

African Journals Online (AJOL)

In this study, an improved plating assay was developed for detection of the number of recombinant phage Cap-T7 present in a test solution at a certain dilution point by counting the plaque forming units. The data demonstrated that the improved plating assay is fast, useful, and convenient for the determination of the phage ...

Advanced Shipboard Communications Demonstrations with ACTS

Science.gov (United States)

Axford, Roy A.; Jedrey, Thomas C.; Rupar, Michael A.

2000-01-01

For ships at sea. satellites provide the only option for high data rate (HDR), long haul communications. Furthermore the demand for HDR satellite communications (SATCOM) for military and commercial ships. and other offshore platforms is increasing. Presently the bulk of this maritime HDR SATCOM connectivity is provided via C-band and X-band. However, the shipboard antenna sizes required to achieve a data rate of, say T 1 (1.544 Mbps) with present C-/X-band SATCOM systems range from seven to ten feet in diameter. This limits the classes of ships to which HDR services can be provided to those which are large enough to accommodate the massive antennas. With its high powered K/Ka-band spot beams, the National Aeronautics and Space Administration's (NASA) Advanced Communications Technology Satellite (ACTS) was able to provide T I and higher rate services to ships at sea using much smaller shipboard antennas. This paper discusses three shipboard HDR SATCOM demonstrations that were conducted with ACTS between 1996 and 1998. The first demonstration involved a 2 Mbps link provided to the seismic survey ship MN Geco Diamond equipped with a 16-inch wide, 4.5-inch tall, mechanically steered slotted waveguide array antenna developed by the Jet Propulsion Laboratory. In this February 1996 demonstration ACTS allowed supercomputers ashore to process Geco Diamond's voluminous oceanographic seismic data in near real time. This capability allowed the ship to adjust its search parameters on a daily basis based on feedback from the processed data, thereby greatly increasing survey efficiency. The second demonstration was conducted on the US Navy cruiser USS Princeton (CG 59) with the same antenna used on Geco Diamond. Princeton conducted a six-month (January-July 1997) Western Hemisphere solo deployment during which time T1 connectivity via ACTS provided the ship with a range of valuable tools for operational, administrative and quality-of-life tasks. In one instance, video

Quality Improvement Initiative in School-Based Health Centers across New Mexico

Science.gov (United States)

Booker, John M.; Schluter, Janette A.; Carrillo, Kris; McGrath, Jane

2011-01-01

Background: Quality improvement principles have been applied extensively to health care organizations, but implementation of quality improvement methods in school-based health centers (SBHCs) remains in a developmental stage with demonstration projects under way in individual states and nationally. Rural areas, such as New Mexico, benefit from the…

Optical Verification Laboratory Demonstration System for High Security Identification Cards

Science.gov (United States)

Javidi, Bahram

1997-01-01

Document fraud including unauthorized duplication of identification cards and credit cards is a serious problem facing the government, banks, businesses, and consumers. In addition, counterfeit products such as computer chips, and compact discs, are arriving on our shores in great numbers. With the rapid advances in computers, CCD technology, image processing hardware and software, printers, scanners, and copiers, it is becoming increasingly easy to reproduce pictures, logos, symbols, paper currency, or patterns. These problems have stimulated an interest in research, development and publications in security technology. Some ID cards, credit cards and passports currently use holograms as a security measure to thwart copying. The holograms are inspected by the human eye. In theory, the hologram cannot be reproduced by an unauthorized person using commercially-available optical components; in practice, however, technology has advanced to the point where the holographic image can be acquired from a credit card-photographed or captured with by a CCD camera-and a new hologram synthesized using commercially-available optical components or hologram-producing equipment. Therefore, a pattern that can be read by a conventional light source and a CCD camera can be reproduced. An optical security and anti-copying device that provides significant security improvements over existing security technology was demonstrated. The system can be applied for security verification of credit cards, passports, and other IDs so that they cannot easily be reproduced. We have used a new scheme of complex phase/amplitude patterns that cannot be seen and cannot be copied by an intensity-sensitive detector such as a CCD camera. A random phase mask is bonded to a primary identification pattern which could also be phase encoded. The pattern could be a fingerprint, a picture of a face, or a signature. The proposed optical processing device is designed to identify both the random phase mask and the

Improving tapping mode atomic force microscopy with piezoelectric cantilevers

International Nuclear Information System (INIS)

Rogers, B.; Manning, L.; Sulchek, T.; Adams, J.D.

2004-01-01

This article summarizes improvements to the speed, simplicity and versatility of tapping mode atomic force microscopy (AFM). Improvements are enabled by a piezoelectric microcantilever with a sharp silicon tip and a thin, low-stress zinc oxide (ZnO) film to both actuate and sense deflection. First, we demonstrate self-sensing tapping mode without laser detection. Similar previous work has been limited by unoptimized probe tips, cantilever thicknesses, and stress in the piezoelectric films. Tests indicate self-sensing amplitude resolution is as good or better than optical detection, with double the sensitivity, using the same type of cantilever. Second, we demonstrate self-oscillating tapping mode AFM. The cantilever's integrated piezoelectric film serves as the frequency-determining component of an oscillator circuit. The circuit oscillates the cantilever near its resonant frequency by applying positive feedback to the film. We present images and force-distance curves using both self-sensing and self-oscillating techniques. Finally, high-speed tapping mode imaging in liquid, where electric components of the cantilever require insulation, is demonstrated. Three cantilever coating schemes are tested. The insulated microactuator is used to simultaneously vibrate and actuate the cantilever over topographical features. Preliminary images in water and saline are presented, including one taken at 75.5 μm/s - a threefold improvement in bandwidth versus conventional piezotube actuators

Code Team Training: Demonstrating Adherence to AHA Guidelines During Pediatric Code Blue Activations.

Science.gov (United States)

Stewart, Claire; Shoemaker, Jamie; Keller-Smith, Rachel; Edmunds, Katherine; Davis, Andrew; Tegtmeyer, Ken

2017-10-16

Pediatric code blue activations are infrequent events with a high mortality rate despite the best effort of code teams. The best method for training these code teams is debatable; however, it is clear that training is needed to assure adherence to American Heart Association (AHA) Resuscitation Guidelines and to prevent the decay that invariably occurs after Pediatric Advanced Life Support training. The objectives of this project were to train a multidisciplinary, multidepartmental code team and to measure this team's adherence to AHA guidelines during code simulation. Multidisciplinary code team training sessions were held using high-fidelity, in situ simulation. Sessions were held several times per month. Each session was filmed and reviewed for adherence to 5 AHA guidelines: chest compression rate, ventilation rate, chest compression fraction, use of a backboard, and use of a team leader. After the first study period, modifications were made to the code team including implementation of just-in-time training and alteration of the compression team. Thirty-eight sessions were completed, with 31 eligible for video analysis. During the first study period, 1 session adhered to all AHA guidelines. During the second study period, after alteration of the code team and implementation of just-in-time training, no sessions adhered to all AHA guidelines; however, there was an improvement in percentage of sessions adhering to ventilation rate and chest compression rate and an improvement in median ventilation rate. We present a method for training a large code team drawn from multiple hospital departments and a method of assessing code team performance. Despite subjective improvement in code team positioning, communication, and role completion and some improvement in ventilation rate and chest compression rate, we failed to consistently demonstrate improvement in adherence to all guidelines.

Hydrogen fueling demonstration projects using compact PSA purification

International Nuclear Information System (INIS)

Ng, E.; Smith, T.

2004-01-01

'Full text:' Hydrogen fueling demonstration projects are critical to the success of hydrogen as an automotive fuel by building public awareness and demonstrating the technology required to produce, store, and dispense hydrogen. Over 75 of these demonstration projects have been undertaken or are in the planning stages world-wide, sponsored by both the public and private sectors. Each of these projects represents a unique combination of sponsors, participants, geographic location, and hydrogen production pathway. QuestAir Technologies Inc., as the industry leader in compact pressure swing adsorption equipment for purifying hydrogen, has participated in four hydrogen fueling demonstration projects with a variety of partners and in North America and Japan. QuestAir's experiences as a participant in the planning, construction, and commissioning of these demonstration projects will be presented in this paper. The unique challenges of each project and the critical success factors that must to be considered for successful deployment of high-profile, international, and multi-vendor collaborations will also be discussed. The paper will also provide insights on the requirements for hydrogen fueling demonstration projects in the future. (author)

Strategies for improving quality and methods for innovation services

Directory of Open Access Journals (Sweden)

Bajić Milan

2009-01-01

Full Text Available Contemporary concepts of business of service organisations, focus their researches on measuring quality of the services and identification of mistakes. The aim of strategies is the improvement of quality. Marketing concepts shows that the constant creation of new products and the modification of characteristics on the old products, makes possible market strategy that stimulates development of activities. This paper is focusing on the improving of service using the strategies that can innovate and improve the services. Paper seeks to demonstrate one of possible observations and importance of performance, combined with blueprinting of services and benchmarking as a useful strategies for improving and innovation of services.

Process Evaluation and Continuous Improvement in Community Youth Programs